19 CFR 11.6 - Distilled spirits, wines, and malt liquors in bulk.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Distilled spirits, wines, and malt liquors in bulk...; DEPARTMENT OF THE TREASURY PACKING AND STAMPING; MARKING Packing and Stamping § 11.6 Distilled spirits, wines... conveying imported distilled spirits, wines, and malt liquors, in accordance with 19 U.S.C. 467. (b) Marks...

Quantitative determination of acid oils in low-temperature coal tar by means of fractional distillation

Energy Technology Data Exchange (ETDEWEB)

Jaeger, A

1950-01-01

The aromatic hydroxy compounds in low-temperature tar were separated, and 75 compounds in the boiling range 180/sup 0/ to 320/sup 0/ isolated by means of fractional distillation in packed columns of at least 45 theoretical plates. Mixtures not separable by fractionation were separated by means of other physicochemical or chemical methods. Hydroxy compounds with boiling point up to 230/sup 0/C were detemined quantitatively, as were the phenols present in low-temperature carbonization liquors. With the Krupp-Lurgi process of low-temperature carbonization, 1.8% phenol, 1.8% o-cresol, and 3.6% m-p-cresols were formed. The tar contained up to 1.3% 1:3:5-xylenol and up to 0.9% 1:2:4-xylenol. Of the 12.1% v/v of phenol, cresols, and xylenols present in tar, 11.2% were determined quantitatively, and 9 hydroxy compounds were identified in the remaining 0.9%. On the basis of these investigations, a technical plant that permitted the recovery of pure low-temperature tar phenols and the preparation of a number of different phenol resins from the mixtures was erected.

Fractional treatment of spent scintillation cocktail with low level tritium by azeotropic distillation

International Nuclear Information System (INIS)

Nishikawa, Masabumi; Kotoh, Kenji; Koga, Keisuke; Katase, Akira

1982-01-01

Among various waste from RI laboratories, one of the most troublesome wastes is the spent liquid scintillation cocktail, because there are no good disposal way but to store in each laboratories. The fractionation of tritiated water, solvent and alkyl detergent from the spent scintillation cocktail by the azeotropic distillation method is examined in this study, and it has been concluded that this method is applicable, It is also found in this study that removal of tritiated water from distilled solvent can be conducted by using adsorption tower with Molecular sieve 3A. Treatment of the spent scintillation cocktail within 3 months after use is recomended because no isotope exchange reaction with solvent or detergent is observed within 3 months after use in this study. No isotope effects are observed in the zeotropic distillation process. (author)

A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions.

Science.gov (United States)

Boczkaj, Grzegorz; Przyjazny, Andrzej; Kamiński, Marian

2011-03-01

The distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures is often investigated by simulated distillation (SIMDIS) using capillary gas chromatography (CGC) with a short capillary column with polydimethylsiloxane as the stationary phase. This paper presents the results of investigations on the possibility of replacing currently used CGC columns for SIMDIS with a deactivated fused silica capillary tube without any stationary phase. The SIMDIS technique making use of such an empty fused silica column allows a considerable lowering of elution temperature of the analytes, which results in a decrease of the final oven temperature while ensuring a complete separation of the mixture. This eliminates the possibility of decomposition of less thermally stable mixture components and bleeding of the stationary phase which would result in an increase of the detector signal. It also improves the stability of the baseline, which is especially important in the determination of the end point of elution, which is the basis for finding the final temperature of distillation. This is the key parameter for the safety process of hydrocracking, where an excessively high final temperature of distillation of a batch can result in serious damage to an expensive catalyst bed. This paper compares the distribution of distillation temperatures of the fraction from vacuum distillation of petroleum obtained using SIMDIS with that obtained by the proposed procedure. A good agreement between the two procedures was observed. In addition, typical values of elution temperatures of n-paraffin standards obtained by the two

Catalytic distillation process

Science.gov (United States)

Smith, L.A. Jr.

1982-06-22

A method is described for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C[sub 4] feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

Anaesthetic effects of Adenia gummifera distillates on Apis mellifera (Honeybee).

Science.gov (United States)

Ngarivhume, T; Dzomba, P; Gwizangwe, I; Zendera, C H; Katsvanga, C A T; Jimu, L; Moyo, M; Chagonda, T

2008-01-01

The anaesthetic activities of steam distillates of Adenia gummifera stem on Apis mellifera were evaluated by a diffusion method. Live, direct and fractional (61-80 degrees C fraction) distillates had greater anaesthetic effect while vacuum distillates were mild. The anaesthetic activity significantly increased with concentration up to 6% (v/v), and then it levelled off, while excessive exposure was lethal. The number of bees in a given volume had no significant effect on anaesthetic activity but container volume (F(cal) = 66.4; F(3,8) = 4.07) and bee-distillate distance (F(cal) = 31.0; F(2,6) = 5.14) did, suggesting the rate of diffusion of active component could be the determining factor. The active component is likely to contain amines and the rest halogenated alkane.

Calculated identification of the output of a refinate in furfurol purification of distillate oil fractions. Raschetnoye opredeleniye vykhoda rafinata pri ochistke furfurolom distillyatnykh maslyanykh fraktsii

Energy Technology Data Exchange (ETDEWEB)

Okhrimenko, N.V.; Dorodnova, V.S.; Martynenko, A.G.; Shiryayeva, G.P.

1983-01-01

The possibility is shown of using an equation proposed by Weigl and Dvayvedi for calculated identification of the outputs of a refinate in furfurol purification of gas oil fractions as applied to the purification of distillate oil fractions (350 to 420 and 420 to 500 degrees of a mixture of Eastern Ukrainian oils from the Druzhba pipeline with a content of 43.6 and 53.8 percent aromatic hydrocarbons (ArU). The deviations between the calculated values of the refinate output and the actual do not exceed 0.5 to 1.5 percent.

Influence of essential oil fractionation by vacuum distillation on acaricidal activity against the cattle tick

Directory of Open Access Journals (Sweden)

Fernando Cidade Torres

2012-08-01

Full Text Available The aim of this work was to study the influence of essential oil fractionation on acaricidal activity against the cattle tick Rhipicephalus (Boophilus microplus. The citronella (Cymbopogon winterianus J. and pepper tree (Schinus molle L. essential oils were fractionated by vacuum distillation yielding fractions that were analyzed by the GC/MS. Laboratory tests were carried out to determine the effect of the total essential oil and fractions on larvae of the cattle tick R. (B. microplus. The fractions 04 and 05 of the C. winterianus essential oil were the most active showing LC50 values of 1.20 and 1.34 μL/mL, respectively. The LC50 of the total oil was 3.30 μL/mL while the effect of the fractions 01, 02 and 03 was less pronounced, with LC50 values of 4.37, 4.24 and 3.49 μL/mL, respectively. The fraction 03 of the S. molle essential oil was the most active showing LC50 value of 8.80 μL/mL while the fractions 01 and 02 did not show toxic effects on the larvae.

Use of a post-production fractionation process improves the nutritional value of wheat distillers grains with solubles for young broiler chicks

OpenAIRE

Thacker, Philip; Deep, Aman; Beltranena, Eduardo

2013-01-01

Background Post-production fractionation of wheat distillers grains with solubles (DDGS) increases their crude protein content and reduces their fiber content. This experiment was conducted to determine the effects of fractionation of wheat DDGS on apparent total tract digestibility (ATTD) and performance when fed to broiler chicks (0?21 d). Methods A total of 150, day-old, male broiler chicks (Ross-308 line; Lilydale Hatchery, Wynyard, Saskatchewan) weighing an average of 49.6 ? 0.8 g were a...

40 CFR 721.7020 - Distillates (petroleum), C(3-6), polymers with styrene and mixed terpenes (generic name).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Distillates (petroleum), C(3-6... CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.7020 Distillates (petroleum... significant new uses subject to reporting. (1) The chemical substance distillates (petroleum), C(3-6...

PLS models for determination of SARA analysis of Colombian vacuum residues and molecular distillation fractions using MIR-ATR

Directory of Open Access Journals (Sweden)

Jorge A. Orrego-Ruiz

2014-06-01

Full Text Available In this work, prediction models of Saturates, Aromatics, Resins and Asphaltenes fractions (SARA from thirty-seven vacuum residues of representative Colombian crudes and eighteen fractions of molecular distillation process were obtained. Mid-Infrared (MIR Attenuated Total Reflection (ATR spectroscopy in combination with partial least squares (PLS regression analysis was used to estimate accurately SARA analysis in these kind of samples. Calibration coefficients of prediction models were for saturates, aromatics, resins and asphaltenes fractions, 0.99, 0.96, 0.97 and 0.99, respectively. This methodology permits to control the molecular distillation process since small differences in chemical composition can be detected. Total time elapsed to give the SARA analysis per sample is 10 minutes.

Advanced distillation curve measurements for corrosive fluids: Application to two crude oils

Energy Technology Data Exchange (ETDEWEB)

Lisa Starkey Ott; Beverly L. Smith; Thomas J. Bruno [National Institute of Standards and Technology, Boulder, CO (United States). Physical and Chemical Properties Division

2008-10-15

We have recently introduced several important improvements in the measurement of distillation curves for complex fluids. The modifications include a composition-explicit data channel for each distillate fraction (for both qualitative and quantitative analysis) and corrosivity assessment of each distillate fraction. The composition-explicit information is achieved with a new sampling approach that allows precise qualitative as well as quantitative analyses of each fraction, on the fly. We have applied the new method to a variety of fluids, including simple n-alkanes, rocket propellant, gasoline, jet fuels, and a hydrocarbon fluid made corrosive with dissolved hydrogen sulfide. In the current contribution, we present the application of the advanced distillation curve method to two samples of crude oil. A primary motivation behind the work is to precisely measure the distillation curves of these oils using our advanced distillation apparatus; these low uncertainty measurements of true thermodynamic state points can be used for equation of state development and differentiation of crude oil samples. Then, the information content of each distillation was extended much further by use of the composition-explicit data channel: gas chromatography-mass spectrometry (GC-MS), infrared spectrophotometry (IR), gas chromatography with sulfur chemiluminescence detection (GC-SCD), and the copper strip corrosion test (CSCT) were used for each distillate volume fraction sampled. Consequently, for each volume fraction of crude oil distillate sampled, we can address the composition, quantitate the total sulfur content, and measure the corrosivity. 39 refs., 6 figs., 2 tabs.

Evaluation of protective effect of deposits formed by naphthenic corrosion and sulfidation on carbon steel and steel 5Cr-0.5Mo exposed in atmospheric distillation fractions

Directory of Open Access Journals (Sweden)

Gloria Duarte

2017-05-01

Full Text Available Refining of so-called opportunity crude oils with a high level of naphthenic acids and sulfur compounds has been increasing interest due to limited availability of light crude oils, however, considerable corrosive effects in the processing to high temperature on pipes and distillation towers mainly by the attack of naphthenic acids and sulfur compounds; sulfur compounds could be corrosive or can reduce the attack of naphthenic acids due to the formation of sulfides layers on the metal surface. In this work was evaluated the performance of deposits formed on the surface of carbon steel AISI SAE 1020 and 5% Cr-0.5% Mo steel exposed in crude oil fractions obtained from atmospheric distillation tower. For this, gravimetric tests were performed in dynamic autoclave using metal samples pre-treated in a crude oil fraction obtained from the atmospheric distillation tower of the Crude Distillation Unit (CDU # 1 in order to form layers of sulfides on the surface of the two materials and subsequently to expose pre-treated and non-pretreated samples in two different crude oil fractions obtained from atmospheric distillation tower of Crude Distillation Unit (CDU # 2. The evaluation showed that the samples pretreated decreased tendency to corrosion by naphthenic acids and sulfidation compared to untreated samples.

Fractionation of distillers dried grains with solubles (DDGS) by sieving and winnowing.

Science.gov (United States)

Liu, KeShun

2009-12-01

Four commercial samples of distillers dried grains with solubles (DDGS) were sieved. All sieved fractions except for the pan fraction, constituting about 90% of original mass, were then winnowed with an air blast seed cleaner. Sieving was effective in producing fractions with varying composition. As the particle size decreased, protein and ash contents increased, and total carbohydrate (CHO) decreased. Winnowing sieved fractions was also effective in shifting composition, particularly for larger particle classes. Heavy sub-fractions were enriched in protein, oil and ash, while light sub-fractions were enriched for CHO. For protein, the combination of the two procedures resulted in a maximum 56.4% reduction in a fraction and maximum 60.2% increase in another fraction. As airflow velocity increased, light sub-fraction mass increased, while the compositional difference between the heavy and light sub-fractions decreased. Winnowing three times at a lower velocity was as effective as winnowing one time at a medium velocity. Winnowing the whole DDGS was much less effective than winnowing sieved fractions in changing composition, but sieving winnowed fractions was more effective than sieving whole DDGS. The two combination sequences gave comparable overall effects but sieving followed by winnowing is recommended because it requires less time. Regardless of combinational sequence, the second procedure was more effective in shifting composition than the first procedure.

Recycling of Waste Acetone by Fractional Distillation

Science.gov (United States)

Weires, Nicholas A.; Johnston, Aubrey; Warner, Don L.; McCormick, Michael M.; Hammond, Karen; McDougal, Owen M.

2011-01-01

Distillation is a ubiquitous technique in the undergraduate organic chemistry curriculum; the technique dates back to ca. 3500 B.C.E. With the emergence of green chemistry in the 1990s, the importance of emphasizing responsible waste management practices for future scientists is paramount. Combining the practice of distillation with the message…

Distillation fraction-specific ecotoxicological evaluation of a paraffin-rich crude oil.

Science.gov (United States)

Erlacher, Elisabeth; Loibner, Andreas P; Kendler, Romana; Scherr, Kerstin E

2013-03-01

Crude oil is a complex mixture of petroleum hydrocarbons (PHC) with distinct chemical, physical and toxicological properties relevant for contaminated site risk assessment. Ecotoxicological effects of crude oil distillation fractions on luminescent bacteria (Vibrio fischeri), earthworms (Dendrobaena hortensis) and invertebrates (Heterocypris incongruens) were tested using two spiked soils and their elutriates. Fraction 2 (F2) had an equivalent carbon number (ECN) range of >10 to 16, and F3 from >16 to 39. F2 showed a substantially higher ecotoxicological effect than F3 for Vibrio and Dendrobaena. In contrast, severe inhibition of Heterocypris by the poorly soluble F3 is attributed to mechanical organ blockage. Immediate sequestration of PHC to the organic matter-rich soil effected reduced toxicity for all organisms. This study indicates that a more differentiated consideration (i) of PHC mixtures based on ECN range and (ii) of model soil properties employed for ecotoxicity testing should be included into PHC-contaminated site risk assessment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Full characterization of compounds obtained from fractional distillation and upgrading of a HTL biocrude

DEFF Research Database (Denmark)

Pedersen, T. H.; Jensen, C. U.; Sandström, L.

2017-01-01

% of the total biocrude composition is determined. It is demonstrated that a total mass fraction of 48.2% of the biocrude is volatile below 350 °C, comprising mainly value-added marketable ketones, oxygenated aromatics and prospective liquid fuel candidates, which are easily fractionated according to boiling...... points. Novel, high resolution pyr-GCxGC-MS analysis of the residue indicates a high molecular weight aromatic structure, valuable for bio-materials production or for further processing into fuels. The distillate fractions are mildly hydrotreated to show the fuel and chemical precursor potential...... of the volatile components. This results in the formation of mainly hydrocarbons and added-value phenolics. This work takes a significant step by going beyond the biocrude as an intermediate bulk energy product and addressing actual applications and pathways to these....

Distilling hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Schulze, J E

1923-03-19

In distilling mineral oils such as petroleum, shale oil, distillates and topped or residual oils, particularly to obtain lubricating oils, the distillation is carried out under reduced pressures below an absolute pressure of 25 mm. of mercury and preferably below about 5 mm. of mercury, and the distillate is collected in fractions determined by the physical characteristics, such as viscosity, flash point, fire point, etc. Superheated steam may be passed through the liquid during distillation. A horizontal cylindrical still provided with cross braces and peripheral ribs interrupted at the base is connected through a condensing coil immersed in a steam chest and a baffled chamber with distillate receiver and is evacuated by a pump. Steam from a boiler and superheater is injected into the still through a perforated pipe. Steam and light oil vapors passing from the chamber are condensed in a coil.

40 CFR 721.10178 - Distillates (Fischer-Tropsch), hydroisomerized middle, C10-13-branched alkane fraction.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Distillates (Fischer-Tropsch... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10178 Distillates (Fischer-Tropsch... to reporting. (1) The chemical substance identified as distillates (Fischer-Tropsch), hydroisomerized...

Evaluation of chemical composition of defect wine distillates

OpenAIRE

Mihaljević Žulj, Marin; Posavec, Barbara; Škvorc, Melanija; Tupajić, Pavica

2016-01-01

The aim of this study was to evaluate the chemical composition of the distillate obtained from wine with off-flavour. The chemical composition of wine distillates obtained by distillation of Chardonnay wine with oxidation off-flavour was investigated. Distillation of wine was carried out using a simple distillation pot still by double distillation and separation the different portion of the first fraction. Volatile compounds of wine and wine distillates (acetaldehyde, ethyl acetate, methanol ...

Sequential Elution of Essential Oil Constituents during Steam Distillation of Hops (Humulus lupulus L.) and Influence on Oil Yield and Antimicrobial Activity.

Science.gov (United States)

Jeliazkova, Ekaterina; Zheljazkov, Valtcho D; Kačániova, Miroslava; Astatkie, Tess; Tekwani, Babu L

2018-06-07

The profile and bioactivity of hops (Humulus lupulus L.) essential oil, a complex natural product extracted from cones via steam distillation, depends on genetic and environmental factors, and may also depend on extraction process. We hypothesized that compound mixtures eluted sequentially and captured at different timeframes during the steam distillation process of whole hop cones would have differential chemical and bioactivity profiles. The essential oil was collected sequentially at 8 distillation time (DT) intervals: 0-2, 2-5, 5-10, 10-30, 30-60, 60-120, 120-180, and 180-240 min. The control was a 4-h non-interrupted distillation. Nonlinear regression models described the DT and essential oil compounds relationship. Fractions yielded 0.035 to 0.313% essential oil, while control yielded 1.47%. The oil eluted during the first hour was 83.2%, 9.6% during the second hour, and only 7.2% during the second half of the distillation. Essential oil (EO) fractions had different chemical profile. Monoterpenes were eluted early, while sequiterpenes were eluted late. Myrcene and linalool were the highest in 0-2 min fraction, β-caryophyllene, β-copaene, β-farnesene, and α-humulene were highest in fractions from middle of distillation, whereas α- bergamotene, γ-muurolene, β- and α-selinene, γ- and δ-cadinene, caryophyllene oxide, humulne epoxide II, τ-cadinol, and 6-pentadecen-2-one were highest in 120-180 or 180-240 min fractions. The Gram-negative Escherichia coli was strongly inhibited by essential oil fractions from 2-5 min and 10-30 min, followed by oil fraction from 0-2 min. The strongest inhibition activity against Gram-negative Yersinia enterocolitica, and Gram-positive Clostridium perfringens, Enterococcus faecalis, and Staphylococcus aureus subs. aureus was observed with the control essential oil. This is the first study to describe significant activity of hops essential oils against Trypanosoma brucei, a parasitic protozoan that causes African

Investigation of the toxicokinetics of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

Science.gov (United States)

Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

2013-04-01

The Canada-wide standards for petroleum hydrocarbons in soils regulate petroleum hydrocarbons based on four distillate ranges: F1 (C6-C10), F2 (>C10-C16), F3 (>C16-C34), and F4 (>C34). Previous toxicity tests with earthworms and F2, as well as two subfractions of F3, F3a (>C16-C23) and F3a (>C23-C34), indicate that test durations might not be sufficiently long to reach threshold effect concentrations, likely because of the differing toxicokinetics for each distillate. A study was conducted to determine the toxicokinetics of both aliphatic and aromatic fractions of F2, F3a, and F3b with the earthworm Eisenia andrei. Peak accumulation curves were observed for F2 aliphatics and aromatics and F3a aromatics, likely as a result of changes in exposure concentration over the test duration via loss or a decrease in the bioavailable fraction. Biota-soil accumulation factors were >1 for total F2 aliphatics and aromatics and F3a aromatics as well as for several individual polyaromatic hydrocarbons for each distillate. Aromatics were disproportionately accumulated over aliphatics and were the main contributors to toxicity; therefore, aromatics and aliphatics should be regulated separately. The toxicokinetics were used to interpret previous toxicity data. Higher molecular weight distillates need longer-than-standard test durations to determine toxicity, so toxicity test results from fixed, standard-duration tests are not strictly comparable for these petroleum distillates. Copyright © 2013 SETAC.

Apparatus for distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Carthaus, E; von Rittersberg, K; Abraham, A

1917-05-03

Apparatus for dry distillation of bituminous material, such as oil shale and brown coal with simultaneous fractional separation of the distillate, consists in the fact, that the domed water-cooled condenser, arranged above the conveyer carrying it, is divided by double vertical partitions in the chamber.

Companded total condensation loxboil air distillation

International Nuclear Information System (INIS)

Erickson, D.C.

1989-01-01

This patent describes a dual pressure cryogenic distillation process for producing gaseous oxygen from a supply of compressed and cleaned air, comprising: a. cooling a major fraction of the compressed and cleaned air; b. rectifying the major fraction in a high pressure rectifier to liquid nitrogen overhead product and kettle liquid bottom product; c. distilling the kettle liquid in a low pressure column to liquid oxygen bottom product and gaseous nitrogen overhead product; d. working expanding a compensating vapor comprised of at least 77% N/sub 2/ thereby producing refrigeration; and e. further compressing the remaining minor fraction comprising no more than about 30% of the compressed, cleaned warm air in a compressor powered by the expansion

Distilling hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

Turner, C

1917-11-23

In the fractional or destructive distillation of hydrocarbon oils or other liquids, the pressure in the still is raised and lowered alternately. The still is closed to raise the pressure, and is opened to lower the pressure rapidly solely by expansion of the vapors. The operation is effected without intermittent cooling, except such as may occur during the lowering of the pressure. In distilling hydrocarbon oil, pressure steam is blown into the oil until the pressure reaches 5 lb/in./sup 2/. The vapor outlet is then opened until the pressure falls to 2 lb/in./sup 2/, whereupon the vapor outlet is closed and steam is again admitted. The operation is continued until the steam, which is of 20 lb pressure, no longer effects distillation; after this stage, superheated steam is used.

Distillation Parameters for Pilot Plant Production of Laurus nobilis Essential oil

Directory of Open Access Journals (Sweden)

Temel Özek

2012-01-01

Full Text Available Essential oils have increasing importance in flavour and fragrance industries. They are obtained by distillation techniques. In order to produce an oil with market potential its optimum production parameters have to be well known prior to its commercial production. Determination of the steam distillation parameters of commercially available Laurel leaves oil in pilot plant scale is described. The effect of steam rate and processing time play a major role in distillation of essential oils. Distillation speed was high in the beginning of the process, then gradually reduced as the distillation proceeded. The main component of the oil of Laurel leaf oil was 1,8-cineole accumulating significantly in the early fractions.

An Investigation into the Relationship Between Distillate Yield and Stable Isotope Fractionation

Science.gov (United States)

Sowers, T.; Wagner, A. J.

2016-12-01

Recent breakthroughs in laser spectrometry have allowed for faster, more efficient analyses of stable isotopic ratios in water samples. Commercially available instruments from Los Gatos Research and Picarro allow users to quickly analyze a wide range of samples, from seawater to groundwater, with accurate isotope ratios of D/H to within ± 0.2 ‰ and 18O/16O to within ± 0.03 ‰. While these instruments have increased the efficiency of stable isotope laboratories, they come with some major limitations, such as not being able to analyze hypersaline waters. The Los Gatos Research Liquid Water Isotope Analyzer (LWIA) can accurately and consistently measure the stable isotope ratios in waters with salinities ranging from 0 to 4 grams per liter (0 to 40 parts per thousand). In order to analyze water samples with salinities greater than 4 grams per liter, however, it was necessary to develop a consistent method through which to reduce salinity while causing as little fractionation as possible. Using a consistent distillation method, predictable fractionation of δ 18O and δ 2 H values was found to occur. This fractionation occurs according to a linear relationship with respect to the percent yield of the water in the sample. Using this method, samples with high salinity can be analyzed using laser spectrometry instruments, thereby enabling laboratories with Los Gatos or Picarro instruments to analyze those samples in house without having to dilute them using labor-intensive in-house standards or expensive premade standards.

High performance liquid chromatographic hydrocarbon group-type analyses of mid-distillates employing fuel-derived fractions as standards

Science.gov (United States)

Seng, G. T.; Otterson, D. A.

1983-01-01

Two high performance liquid chromatographic (HPLC) methods have been developed for the determination of saturates, olefins and aromatics in petroleum and shale derived mid-distillate fuels. In one method the fuel to be analyzed is reacted with sulfuric acid, to remove a substantial portion of the aromatics, which provides a reacted fuel fraction for use in group type quantitation. The second involves the removal of a substantial portion of the saturates fraction from the HPLC system to permit the determination of olefin concentrations as low as 0.3 volume percent, and to improve the accuracy and precision of olefins determinations. Each method was evaluated using model compound mixtures and real fuel samples.

Raman spectroscopy for the characterization of different fractions of hemp essential oil extracted at 130 °C using steam distillation method

Science.gov (United States)

Hanif, Muhammad Asif; Nawaz, Haq; Naz, Saima; Mukhtar, Rubina; Rashid, Nosheen; Bhatti, Ijaz Ahmad; Saleem, Muhammad

2017-07-01

In this study, Raman spectroscopy along with Principal Component Analysis (PCA) is used for the characterization of pure essential oil (pure EO) isolated from the leaves of the Hemp (Cannabis sativa L.,) as well as its different fractions obtained by fractional distillation process. Raman spectra of pure Hemp essential oil and its different fractions show characteristic key bands of main volatile terpenes and terpenoids, which significantly differentiate them from each other. These bands provide information about the chemical composition of sample under investigation and hence can be used as Raman spectral markers for the qualitative monitoring of the pure EO and different fractions containing different active compounds. PCA differentiates the Raman spectral data into different clusters and loadings of the PCA further confirm the biological origin of the different fractions of the essential oil.

The Use of Fuel Gas as Stripping Medium in Atmospheric Distillation of Crude Oil L’utilisation de gaz combustible comme moyen d’extraction des fractions légères en distillation atmosphérique du pétrole brut

Directory of Open Access Journals (Sweden)

Plellis-Tsaltakis C.

2011-09-01

Full Text Available Stripping of petroleum fractions aims to remove the light ends that spoil some of their properties, such as the flash point. Stripping usually employs steam for that purpose. Except for steam, other substances can perform the same function, among them light hydrocarbons. In this article, we investigate the use of refinery fuel gas as stripping medium for a crude oil atmospheric distillation unit. L’extraction des fractions légères du pétrole vise à enlever les produits nuisibles à certaines propriétés comme le point d’éclair. Cette opération utilise habituellement de la vapeur d’eau. D’autres substances peuvent remplir la même fonction, comme les hydrocarbures légers. Dans cet article, on étudie l’utilisation du gaz combustible de la raffinerie comme moyen d’extraction des fractions légères dans une unité de distillation atmosphérique.

27 CFR 27.1 - Imported distilled spirits, wines, and beer.

Science.gov (United States)

2010-04-01

..., wines, and beer. 27.1 Section 27.1 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS IMPORTATION OF DISTILLED SPIRITS, WINES, AND BEER Scope of Regulations § 27.1 Imported distilled spirits, wines, and beer. This part, “Importation of...

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Cosden, S; Cosden, J S

1937-09-08

A means and process are described for the destructive distillation of solid carbonaceous materials in which the process comprises charging the material, in a finely divided condition into a stream of hot combustion gases, and allows the hot gases to act pyrolytically on the organic compounds contained in the material, separating the volatile liberated constituents from residuary constituents. Hot reaction gases are generated by fuel ignition means in a generator and are immediately intermingled with comminuted carbonaceous material from a hopper, in a narrow conduit. The mixture of material and reaction fluid is then passed through an elongated confined path, which is exteriorly heated by the combustion chamber of the furnace, where the destructive distillation is effected. Volatile and solid constituents are separated in the chamber, and the volatile constituents are fractionated and condensed.

Elementary Analysis of Petroleum Distillates by Gc-Aed: Validation and Application to the Calculation of Distillation Profile Properties

Directory of Open Access Journals (Sweden)

Baco F.

1999-07-01

Full Text Available This article describes the development of elementary analysis in the distillation profile of petroleum cuts by gas phase chromatography-atomic emission detection (GC-AED coupling and shows the application perspectives to characterisation of middle distillates of a piece of information unheard of until now on a routine basis. The performances of the analytical assembly used have been studied for carbon, hydrogen, sulphur and nitrogen analysis. Simulated distillation, a gas phase chromatography analysis which enables determining the weight percentage of distilled matter in relation to the boiling point of petroleum cuts, has been adapted to GC-AED coupling. We have developed a method giving access to three types of information: global elementary composition, simulated distillation and elementary composition in distillation profile, i. e. by fraction (% of the distilled product. The analysis of the atmospheric distillates has been assessed in terms of precision and bias for these various types of information. The validation was carried out notably by comparison with the results obtained using reference analytical methods, on preparative distillation cuts of representative samples. The application of GC-AED to characterisation of distillates is discussed, in particular for classification purposes and for predicting petroleum properties in the distillation profile. The cetane number of gas oils was taken as an example to illustrate the latter application.

Surface active agents from Egyptian petroleum distillates

Energy Technology Data Exchange (ETDEWEB)

Kassem, T.M.

Kerosene and solar distillates from local crude petroleum 'Morgan' were fractionated. These fractions were refined with oleum and then distilled. The normal paraffins were separated from the refined fractions by the urea adduction technique. These paraffin cuts were subjected to 50% chlorination and the obtained monochlorinated paraffins were used in the synthesis of alkylbenzenes and alkyldiphenyls which were converted to anionic surfactants by sulphonation with 95% sulphuric acid. The sulphonyl chlorides of alkylbenzenes and of alkyldiphenyls were prepared and then converted to the corresponding sulphonamides. The prepared sulphonamides were then processed to nonionic surfactants through condensation with ethylene oxide. The ethoxylates were sulphated with chlorosulphonic acid and phosphated with phosphorus pentoxide to anionic surfactants. The surface active properties and the biodegradability of all the prepared surfactants were determined.

Effects of reflux ratio and feed conditions for the purification of bioethanol in a continuous distillation column

Science.gov (United States)

Dasan, Y. K.; Abdullah, M. A.; Bhat, A. H.

2014-10-01

Continuous distillation column was used for the purification of bioethanol from fermentation of molasses using Saccharomyces cerevisia. Bioethanol produced was at 8.32% (v/v) level. The efficiency of continuous distillation process was evaluated based on reflux ratio, and feed condition. The lab results were validated using COFE simulation Software. The analyses showed that both reflux ratio and feed condition had significant effects on the distillation process. Stages increased from 1.79 to 2.26 as the reflux ratio was decreased from 90% to 45% and the saturated feed produced lower mole fraction of desired product. We concluded that the lower reflux ratio with cold feed condition was suitable for higher mole fraction of top product.

Contact structure for use in catalytic distillation

Science.gov (United States)

Jones, E.M. Jr.

1984-03-27

A method is described for conducting catalytic chemical reactions and fractionation of the reaction mixture comprising feeding reactants into a distillation column reactor, contracting said reactant in liquid phase with a fixed bed catalyst in the form of a contact catalyst structure consisting of closed porous containers containing the catalyst for the reaction and a clip means to hold and support said containers, which are disposed above, i.e., on the distillation trays in the tower. The trays have weir means to provide a liquid level on the trays to substantially cover the containers. In other words, the trays function in their ordinary manner with the addition thereto of the catalyst. The reaction mixture is concurrently fractionated in the column. 7 figs.

Distilling solid carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1926-12-04

In the distillation of solid carbonaceous materials with by-product recovery by direct heating with a gas such as water gas, producer gas, or combustion gas which is passed in counter-flow to the materials, the volume of the gas used is such as to lower the vapor tension of the volatiles to enable the oil vapor to be liberated at temperatures not exceeding 450 to 500/sup 0/C and so that the gaseous mixture may be cooled to from 80 to 100/sup 0/C without causing the highest boiling oil fraction to condense. Coking coals may be subjected to a preliminary heat treatment with gases containing an oxygen content of from 2 to 8 percent to reduce their coking properties, and oxygen may be added to the heating gases to assist the polymerization of resinous bodies. Lubricating oil may be obtained by treating the primary oil with caustic soda to remove tar acids, refining the residue with sulfuric acid, distilling off 25 percent of the refined oil and passing the remainder through a filter press at -5/sup 0/C to extract the paraffin wax. The residue of wax-free oil is distilled to yield a lubricating oil which at normal temperatures has a static coefficient of friction of from .1 to .185. Other specifications are referred to.

Fate of DDT in grape juice when fermented and distilled into arak

International Nuclear Information System (INIS)

Kawar, N.S.

1975-01-01

Since DDT is still used on grapevines to control insect pests, the fate of this insecticide in grape juice fermented and distilled into arak was investigated. Fermentation of the juice resulted in extensive conversion of DDT to DDD. Distillation of the fermented juice resulted in further conversion of DDT to DDD. Moreover, the major portion of both DDT and DDD remained in the undistilled fraction. The second distillation resulted in further distribution of DDT and DDD among the four fractions, thus leaving very low levels of both compounds in the finished product. DDT residue in arak constituted only 2% of the amount added to the fresh juice. (author)

Ignition delay times of Gasoline Distillation Cuts measured with Ignition Quality Tester

KAUST Repository

Naser, Nimal

2017-04-21

Tailoring fuel properties to maximize the efficiency of internal combustion engines is a way towards achieving cleaner combustion systems. In this work, the ignition properties of various gasoline fuel distillation cuts are analyzed to better understand fuel properties of the full boiling range fuel. An advanced distillation column (ADC) provides a more realistic representation of volatility characteristics, which can be modeled using equilibrium thermodynamic methods. The temperature reported is that of the liquid, as opposed to the vapor temperature in conventional ASTM D86 distillation standard. Various FACE (fuels for advanced combustion engines) gasolines were distilled and various cuts were obtained. The separated fractions were then tested in an ignition quality tester (IQT) to see the effect of chemical composition of different fractions on their ignition delay time. Fuels with lower aromatic content showed decreasing ignition delay time with increasing boiling point (i.e., molecular weight). However, fuels with higher aromatic content showed an initial decrease in ignition delay time with increasing boiling point, followed by drastic increase in ignition delay time due to fractions containing aromatics. This study also provides an understanding on contribution of different fractions to the ignition delay time of the fuel, which provides insights into fuel stratification utilized in gasoline compression ignition (GCI) engines to tailor heat release rates.

Pear distillates from pear juice concentrate: effect of lees in the aromatic composition.

Science.gov (United States)

García-Llobodanin, L; Achaerandio, I; Ferrando, M; Güell, C; López, F

2007-05-02

Pear juice obtained from pear concentrate was fermented at room temperature using Saccharomyces cerevisiae (BDX, ENOFERM, France) as the fermentation microorganism. During the fermentation process, total sugars were measured. High performance liquid chromatography analyses were used to monitor the fermentation process and to characterize the pear wine. The pear wine obtained was distilled with its lees using three different equipments: a glass alembic (a glass pot still coupled to a glass column), a copper alembic, and a glass alembic with the addition of 5 g/L of copper shavings to the pot still. The same distillations were repeated with the wine without its lees (separated by decanting). Several distillation fractions were collected, up to a total of 500 mL of distillate. Gas chromatography was used to identify and quantify the volatile compounds in each fraction, and the methanol and ethanol contents. Based on these results, the heart fraction was defined. ANOVA tests were performed on the heart fractions to determine quantitative differences between some volatile compounds depending on the equipment used and the presence or absence of the wine lees. From this series of ANOVA tests, it can be concluded that the concentrations of the compounds that are considered to have a negative effect on the quality of the distillates (methanol, ethyl acetate, furfural) decrease or do not change when they are distilled in the presence of lees and in the copper alembic. In addition, the concentrations of the positive compounds (ethyl decanoate and ethyl-2-trans-4-cis-decadienoate) increase in the presence of lees for all of the equipment tested. So, it can be assumed that the distillation of pear wine with its lees in copper alembic leads to a better quality product.

Identification of genotoxic compounds in crude oil using fractionation according to distillation, polarity and Kow.

Science.gov (United States)

Park, Shin Yeong; Lee, Hyo Jin; Khim, Jong Seong; Kim, Gi Beum

2017-01-30

We examined the degree of DNA damage caused by fractions of crude oil in accordance with the boiling points, polarity and log K ow . Relatively high DNA damage was observed in the aromatic fraction (290-330°C) and resin and polar fraction (350-400°C). The resin and polar fraction showed relatively high genotoxicity compared with the aliphatic and aromatic fraction at the 1-4 log K ow range. At the 6-7 log K ow range, the aromatic fraction showed relatively high DNA damage compared with the aliphatic and resin and polar fraction. In particular, every detailed fraction in accordance with the log K ow values (aliphatic and aromatic (310-320°C) and resins and polar fractions (370-380°C)) showed one or less than one DNA damage. However, the fractions before separation in accordance with log K ow values (aliphatic and aromatic (310-320°C) and resin and polar (370-380°C) fractions) showed high DNA damage. Thus, we confirm the synergistic action between the detailed compounds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Structural characterization of asphaltenes from vacuum residue distillation

International Nuclear Information System (INIS)

Silva, Ronaldo C.; Seidl, Peter R.; Menezes, Sonia M.C. de; Teixeira, Marco A.G.

2001-01-01

The aim of this work was to do structural characterization of asphaltenes from different vacuum residues distillation. Several average molecular parameters using some analytical techniques were obtained and these techniques were: nuclear magnetic resonance ( 1 H and 13 C NMR), elemental analysis (C,H,N,O and S content), Fourier transform infrared (FT-IR), vapor pressure osmometry and gel permeation chromatography. Particularly from NMR, some important molecular parameters were obtained, such as aromatic carbon fraction, aliphatic carbons fraction, alkyl substituted aromatic carbons, unsubstituted aromatic carbons, etc. Molecular modeling will be employed to build the structure of asphaltenes using the experimental data. (author)

The Use of Fuel Gas as Stripping Medium in Atmospheric Distillation of Crude Oil L’utilisation de gaz combustible comme moyen d’extraction des fractions légères en distillation atmosphérique du pétrole brut

OpenAIRE

Plellis-Tsaltakis C.; Lygeros A.I.

2011-01-01

Stripping of petroleum fractions aims to remove the light ends that spoil some of their properties, such as the flash point. Stripping usually employs steam for that purpose. Except for steam, other substances can perform the same function, among them light hydrocarbons. In this article, we investigate the use of refinery fuel gas as stripping medium for a crude oil atmospheric distillation unit. L’extraction des fractions légères du pétrole vise à enlever les produits nuisibles à cer...

27 CFR 1.83 - Acquiring or receiving distilled spirits in bulk for addition to wine.

Science.gov (United States)

2010-04-01

... distilled spirits in bulk for addition to wine. 1.83 Section 1.83 Alcohol, Tobacco Products and Firearms... UNDER THE FEDERAL ALCOHOL ADMINISTRATION ACT, NONINDUSTRIAL USE OF DISTILLED SPIRITS AND WINE, BULK... Bottling § 1.83 Acquiring or receiving distilled spirits in bulk for addition to wine. Persons holding...

Quality evaluation of agricultural distillates using different types of electronic noses

Science.gov (United States)

Dymerski, Tomasz; Gebicki, Jacek; Namieśnik, Jacek

2014-08-01

The paper presents the results of investigation on quality evaluation of agricultural distillates using a prototype of electronic nose instrument and a commercial electronic nose of Fast/Flash GC type- HERACLES II. The prototype was equipped with TGS type semiconductor sensors. HERACLES II included two chromatographic columns with different polarity of stationary phase and two FID detectors. In case of the prototype volatile fraction of the agricultural distillate was prepared via barbotage process, whereas HERACLES II analysed the headspace fraction. Classification of the samples into three quality classes was performed using: quadratic discriminant function (QDA), supported with cross-validation method. Over 95% correct classification of the agricultural distillates into particular quality classes was observed for the analyses with HERACLES II. The prototype of electronic nose provided correct classification at the level of 70%.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1927-12-23

Oil bearing solids such as coal, tar sands, oil shales, or the like, are distilled in a current of hot gas and are first preheated to a temperature above that at which the heaviest oil fractions in the vapors are liable to condense, for example 100 to 250/sup 0/C, according to the volume of gas passing through the retort, temperature being in inverse proportion to the quantity of oxygen containing constituents in the charge. When the distillation takes place in a controlled volume of hot inert gas of 45,000 cubic feet per ton and the volume of oil recovered is about 20 gallons per ton, the material is preheated to 200 to 250/sup 0/C, when the volume of gas used is 100,000 cubic feet the preheating temperature is 150/sup 0/C. The temperatures of the retort dust extractor etc. do not fall below 100 to 150/sup 0/C until actual condensation of the oil vapor is desired. Specification 287,381 is referred to, and Specification 287,037 also is referred to in the Provisional Specification.

Improving distillation method and device of tritiated water analysis for ultra high decontamination efficiency

International Nuclear Information System (INIS)

Fang, Hsin-Fa; Wang, Chu-Fang; Lin, Chien-Kung

2015-01-01

It is important that monitoring environmental tritiated water for understanding the contamination dispersion of the nuclear facilities. Tritium is a pure beta radionuclide which is usually measured by Liquid Scintillation Counting (LSC). The average energy of tritum beta is only 5.658 keV that makes the LSC counting of tritium easily be interfered by the beta emitted by other radionuclides. Environmental tritiated water samples usually need to be decontaminated by distillation for reducing the interference. After Fukushima Nucleaer Accident, the highest gross beta concentration of groundwater samples obtained around Fukushima Daiichi Nuclear Power Station is over 1,000,000 Bq/l. There is a need for a distillation with ultra-high decontamination efficiency for environmental tritiated water analysis. This study is intended to improve the heating temperature control for better sub-boiling distillation control and modify the height of the container of the air cooling distillation device for better fractional distillation effect. The DF of Cs-137 of the distillation may reach 450,000 which is far better than the prior study. The average loss rate of the improved method and device is about 2.6% which is better than the bias value listed in the ASTM D4107-08. It is proven that the modified air cooling distillation device can provide an easy-handling, water-saving, low cost and effective way of purifying water samples for higher beta radionuclides contaminated water samples which need ultra-high decontamination treatment. - Highlights: • The improvements of method and device make the decontaminatin factor (DF) of Cs-137 of distillation reach over 450,000. • The decontamination factor ( DF) value may be increased about 20 times by increasing the height of the container from 7 cm to 20 cm. • The device provides an easy-handling, water-saving, low cost, stable and effective way for the distillation of triated water analysis.

Simultaneous valorization and biocatalytic upgrading of heavy vacuum gas oil by the biosurfactant-producing Pseudomonas aeruginosa AK6U.

Science.gov (United States)

Ismail, Wael Ahmed; Mohamed, Magdy El-Said; Awadh, Maysoon N; Obuekwe, Christian; El Nayal, Ashraf M

2017-11-01

Heavy vacuum gas oil (HVGO) is a complex and viscous hydrocarbon stream that is produced as the bottom side product from the vacuum distillation units in petroleum refineries. HVGO is conventionally treated with thermochemical process, which is costly and environmentally polluting. Here, we investigate two petroleum biotechnology applications, namely valorization and bioupgrading, as green approaches for valorization and upgrading of HVGO. The Pseudomonas aeruginosa AK6U strain grew on 20% v/v of HVGO as a sole carbon and sulfur source. It produced rhamnolipid biosurfactants in a growth-associated mode with a maximum crude biosurfactants yield of 10.1 g l -1 , which reduced the surface tension of the cell-free culture supernatant to 30.6 mN m -1 within 1 week of incubation. The rarely occurring dirhamnolipid Rha-Rha-C 12 -C 12 dominated the congeners' profile of the biosurfactants produced from HVGO. Heavy vacuum gas oil was recovered from the cultures and abiotic controls and the maltene fraction was extracted for further analysis. Fractional distillation (SimDist) of the biotreated maltene fraction showed a relative decrease in the high-boiling heavy fuel fraction (BP 426-565 °C) concomitant with increase in the lighter distillate diesel fraction (BP 315-426 °C). Analysis of the maltene fraction revealed compositional changes. The number-average (Mn) and weight-average (Mw) molecular weights, as well as the absolute number of hydrocarbons and sulfur heterocycles were higher in the biotreated maltene fraction of HVGO. These findings suggest that HVGO can be potentially exploited as a carbon-rich substrate for production of the high-value biosurfactants by P. aeruginosa AK6U and to concomitantly improve/upgrade its chemical composition. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Thermo-economic performance of inclined solar water distillation systems

Directory of Open Access Journals (Sweden)

Agboola Phillips O.

2015-01-01

Full Text Available This study investigates the thermo-economic performance of different configurations of inclined solar water desalination for parameters such as daily production, efficiency, system cost and distilled water production cost. The four different configurations considered for this study are as follows; 1. Inclined solar water distillation with bare absorber plate (IISWD with daily production of 5.46 kg/m2 day and daily efficiency of 48.3%. 2. Inclined solar water distillation with wick on absorber plate (IISWDW with daily production of 6.41kg/m2 day and daily efficiency 50.3%. 3. Inclined solar water distillation with wire mesh on absorber plate (IISWDWM with daily production n of 3.03 kg/m2 day and daily efficiency 32.6%. 4. Inclined solar water distillation with bare absorber plate (ISWD. (Control System with daily production of 3.25 kg/m2 day and daily efficiency of 40.1%. The systems potable water cost price ranges from 0.03 $/L for IISWDW to 0.06$/L for IISWDWM System. All the systems are economically and technically feasible as a solar distillation system for potable water in Northern Cyprus. The price of potable water from water vendors/hawkers ranges from 0.11-0.16 $/L. It is more economically viable to have the rooftop inclined solar water desalination system than procuring potable water from vendors.`

Use of corn distiller's solubles from an ethanol plant for aquaculture

Energy Technology Data Exchange (ETDEWEB)

Kohler, C.C.

1984-06-01

Wet stillage can economically be separated into two fractions: distiller's grain and distiller's solubles. Wet corn distiller's grain has shown potential as a feed supplement for ruminants, swine, and poultry. However, the soluble fraction (with suspended particles) is of little food value to terrestrial animals because of its high water content; it is not generally economically feasible to concentrate it further. The purpose of this project is to determine if the soluble by-product could potentially be used as a food source in an aquatic environment where its high water content would not necessarily pose an impediment. Studies have shown that corn distiller's solubles are not highly toxic to aquatic organisms at concentrations ranging up to 10,000 ppM. However, the high biological oxygen demand of the material requires that it be administered to ponds at rates less than 2000 ppM on a daily basis. Golden shiners were observed to actively consume the particulates of the corn distiller's solubles. Direct consumption of the particulates by fish makes the use of corn distiller's solubles in aquaculture much more attractive than if the by-product only serves to increase pond fertility. Despite the minimum amount of food material added to the ponds, production of shrimp and fish was favorable over the 4 month growing periods. Golden shiners reared in the same ponds as shrimp had production rates equivalent to 130 kg ha/sup -1/. Monoculture of shrimp at higher densities (3000 to 5000 shrimp stocked per pond versus 2000 in 1982) resulted in an average production equivalent to approximately 228 kg ha/sup -1/, with individual shrimp averaging 10.5 g. Based on estimated wholesale prices of $10.00 and $7.75 per kilogram for frozen shrimp and live fish, respectively, the gross profit margin would have exceeded $2000 ha/sup -1/ both years. 25 references, 13 figures, 13 tables.

Quality Evaluation of Agricultural Distillates Using an Electronic Nose

OpenAIRE

Dymerski, Tomasz; Gębicki, Jacek; Wardencki, Waldemar; Namieśnik, Jacek

2013-01-01

The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing ...

Characterization of corn stover, distiller grains and cattle manure for thermochemical conversion

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijun; Shahbazi, Abolghasem [Department of Natural Resources and Environmental Design, North Carolina Agricultural and Technical State University, Greensboro, NC 27411 (United States); Hanna, Milford A. [Industrial Agricultural Products Center, Department of Biological Systems Engineering, University of Nebraska-Lincoln, Lincoln, NE 68583-0726 (United States)

2011-01-15

Corn stover, distiller grains and cattle manure were characterized to evaluate their acceptability for thermochemical conversion. The energy densities of ground corn stover, distiller grains and cattle manure after totally drying were 3402, 11,813 and 10,374 MJ/m{sup 3}, compared to 37,125 MJ/m{sup 3} for coal. The contents of volatiles in corn stover, distiller grains and cattle manure were 77.4, 82.6 and 82.8%, respectively, on a dry and ash-free basis compared to 43.6% for coal. About 90% of the volatiles in corn stover, distiller grains and cattle manure were released at pyrolysis temperatures of 497, 573 and 565 C, respectively. The combustion of corn stover, distiller grains and cattle manure were completed at 620, 840 and 560 C, respectively. The heat values of the biomass and air mixture for stoichiometric combustion were 2.64, 2.75 and 1.77 MJ/kg for dried corn stover, distiller grains and cattle manure, respectively, as compared to 2.69 MJ/kg for coal. Combustion of 1 kg of dry corn stover, distiller grains and cattle manure generated 5.33, 6.20 and 5.66 Nm{sup 3} of flue gas, respectively, compared to 8.34 Nm{sup 3} for coal. Simulation showed that gasification of 1 kg of dried corn stover, distiller grains and cattle manure at 850 C and ER of 0.3 generated 2.02, 2.37 and 1.44 Nm{sup 3} dry syngas at a heating value of about 4.5 MJ/Nm{sup 3}, compared to 3.52 Nm{sup 3} at 5.8 MJ/Nm{sup 3} for coal. The molecular ratio of H{sub 2} to CO in the biomass-derived syngas was close to 1.0, compared to about 0.5 for the coal-derived syngas. (author)

The applicability of radiotracers for the investigation of the distillation of hydrocarbons

International Nuclear Information System (INIS)

Graczyk, J.; Iller, E.

1976-01-01

The use of radioactive tracers provide valuable methods for the investigation of distillation processes and have been applied to determine the characteristics of material streams, the dynamics of flowing phases and the composition in various parts of the distillation equipment. A method is proposed for testing individual radiotracers emplozemployed for the investigation of the distillation of hydrocarbons. The method consists in laboratory-scale distillation of a tracer together with a multicomponent hydrocarbon mixture, namely a gasoline fraction. The purification efficiency, distillation characteristics, and effective radiochemical purity of several tracers (reactor activated bromobenzene and synthesized C 3 H 7 82 Br, C 4 H 9 82 Br, C 5 H 11 82 Br) have been investigated. The distillation characteristics of bromohydrocarbons labelled with 82 Br and selected hydrocarbons tagged with 14 C (benzene and cumene) have been compared. The radiotracers investigated were employed for the determination of the hydrodynamic parameters of hydrocarbon distillation in laboratory packed columns and a commercial distillation tower. (author)

FRACTIONATION AND CHARACTERISATION OF TECHNICAL AMMONIUM LIGNOSULPHONATE

Directory of Open Access Journals (Sweden)

Cheryl Ann Leger

2010-08-01

Full Text Available It is difficult to use lignin in any analytical methodology without reducing its considerable polydispersity by fractionation. An ammonium lignosulphonate sample was fractionated using a method of partial solubility in solutions of isopropanol increasingly diluted with distilled water, effectively fractionating by polarity. Selected fractions were characterised by gravimetric determination of the fractions, and determination of acid insoluble lignin, soluble lignin, and carbohydrate contents. Acid-insoluble lignin content was very low, and soluble lignin provided the majority of the lignin content, as should be expected from sulphonated lignin. Carbohydrate contents were also fairly low, the highest percentage at 14.5 being in Fraction 2, with the bulk lignin and Fraction 3 having 6.5% and 3.2%, respectively. Differences in the composition of each fraction support the efficacy of the fractionation process and permitted selection of fractions for use in subsequent studies.

Coal distillation plant

Energy Technology Data Exchange (ETDEWEB)

Overton, P C

1937-05-20

To fractionally condense the vapours derived from the distillation of coal or shale, an apparatus comprises a low temperature carbonisation retort having a plurality of differently heating zones therein which connect with a manifold in which said gas oil vapours can expand. A dephlegmator, cold water jacketted and centrally air heated, causes the heavier matters of the vapours to settle out and the lighter oil gas vapours are conveyed to the bottom of an electrically operated fractionating apparatus comprising a column furnished with a plurality of compartments each heated by electrical elements connected to source of current by lead wires. Annular launders in the compartments collect the derived liquids at the various levels and deliver same by pipes to separate sump while pipe at head of column draws off incondensible gases for return to retort.

Microbial Desulfurization of a Crude Oil Middle-Distillate Fraction: Analysis of the Extent of Sulfur Removal and the Effect of Removal on Remaining Sulfur

Science.gov (United States)

Grossman, M. J.; Lee, M. K.; Prince, R. C.; Garrett, K. K.; George, G. N.; Pickering, I. J.

1999-01-01

Rhodococcus sp. strain ECRD-1 was evaluated for its ability to desulfurize a 232 to 343°C middle-distillate (diesel range) fraction of Oregon basin (OB) crude oil. OB oil was provided as the sole source of sulfur in batch cultures, and the extent of desulfurization and the chemical fate of the residual sulfur in the oil after treatment were determined. Gas chromatography (GC), flame ionization detection, and GC sulfur chemiluminesce detection analysis were used to qualitatively evaluate the effect of Rhodococcus sp. strain ECRD-1 treatment on the hydrocarbon and sulfur content of the oil, respectively. Total sulfur was determined by combustion of samples and measurement of released sulfur dioxide by infrared absorption. Up to 30% of the total sulfur in the middle distillate cut was removed, and compounds across the entire boiling range of the oil were affected. Sulfur K-edge X-ray absorption-edge spectroscopy was used to examine the chemical state of the sulfur remaining in the treated OB oil. Approximately equal amounts of thiophenic and sulfidic sulfur compounds were removed by ECRD-1 treatment, and over 50% of the sulfur remaining after treatment was in an oxidized form. The presence of partially oxidized sulfur compounds indicates that these compounds were en route to desulfurization. Overall, more than two-thirds of the sulfur had been removed or oxidized by the microbial treatment. PMID:9872778

Fractionation and rectification apparatus

Energy Technology Data Exchange (ETDEWEB)

Sauerwald, A

1932-05-25

Fractionation and rectifying apparatus with a distillation vessel and a stirring tube, drainage tubes leading from its coils to a central collecting tube, the drainage tubes being somewhat parallel and attached to the outer half of the stirring tube and partly on the inner half of the central collecting tube, whereby distillation and rectification can be effected in a single apparatus.

Tissue free water tritium separation from foodstuffs by azeotropic distillation

International Nuclear Information System (INIS)

Constantin, F.; Ciubotaru, A.; Popa, D.

1998-01-01

In this paper the tritium separation from tissue free water in foodstuffs by azeotropic distillation is described. Tritium in tissue water is assayed by liquid scintillation counting using well-established quenched correction method. The mean value of the tritium concentration in tissue water from foodstuffs is about 6-12 Bq/l very similar to the tritium mean concentration measured in the surface waters of the area where the samples have been collected (about 12 Bq/l. Therefore, the tritium content in the water fraction of the food samples can be considered in equilibrium with the local environmental water sources. The azeotropic distillation it is an accessible separation method which does not need a sophisticated and expansive distillation apparatus. It is a fast method of separation tissue free water from foodstuffs being very important in the surveillance activity of the environmental within nuclear electric plant. It is suitable for processing a small quantity of samples and for a production type facility when a large number of samples must be processed because the solvent can be purified and reused. The azeotropic distillation has some limits being used to separate water from samples with high content of water (85-90%) and simple a simple chemical structures as: vegetables, fruits, cereal, soil, vegetation. According to the results obtained, the organic substituents of milk, wine, meat (casein, lactose, milk fat, alcohol, esters) may enhance the chemisorption of tritium on through exchange organic hydrogen as -OH, -SH, -NH, -COOH with tritium. Also, the tissue water separation by azeotropic distillation is not complete and can not guarantee the absence of the vaporization isotope effect of the HTO/H 2 O system., However, the azeotropic distillation is the preferred method of the water extraction from food samples, which makes it useful for the tritium transfer from soil to foodstuffs. (authors)

Tissue free water tritium separation from foodstuffs by azeotropic distillation

Energy Technology Data Exchange (ETDEWEB)

Constantin, F; Ciubotaru, A; Popa, D [Inspectorate of Public Health of Bucharest (Romania)

1999-12-31

In this paper the tritium separation from tissue free water in foodstuffs by azeotropic distillation is described. Tritium in tissue water is assayed by liquid scintillation counting using well-established quenched correction method. The mean value of the tritium concentration in tissue water from foodstuffs is about 6-12 Bq/l very similar to the tritium mean concentration measured in the surface waters of the area where the samples have been collected (about 12 Bq/l. Therefore, the tritium content in the water fraction of the food samples can be considered in equilibrium with the local environmental water sources. The azeotropic distillation it is an accessible separation method which does not need a sophisticated and expansive distillation apparatus. It is a fast method of separation tissue free water from foodstuffs being very important in the surveillance activity of the environmental within nuclear electric plant. It is suitable for processing a small quantity of samples and for a production type facility when a large number of samples must be processed because the solvent can be purified and reused. The azeotropic distillation has some limits being used to separate water from samples with high content of water (85-90%) and simple a simple chemical structures as: vegetables, fruits, cereal, soil, vegetation. According to the results obtained, the organic substituents of milk, wine, meat (casein, lactose, milk fat, alcohol, esters) may enhance the chemisorption of tritium on through exchange organic hydrogen as -OH, -SH, -NH, -COOH with tritium. Also, the tissue water separation by azeotropic distillation is not complete and can not guarantee the absence of the vaporization isotope effect of the HTO/H{sub 2}O system., However, the azeotropic distillation is the preferred method of the water extraction from food samples, which makes it useful for the tritium transfer from soil to foodstuffs. (authors) 2 tabs.

Cascade Distillation Subsystem Development: Early Results from the Exploration Life Support Distillation Technology Comparison Test

Science.gov (United States)

Callahan, Michael R.; Patel, Vipul; Pickering, Karen D.

2010-01-01

In 2009, the Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell International, Torrance, California) was assessed in the National Aeronautics and Space Administration (NASA) Exploration Life Support (ELS) distillation comparison test. The purpose of the test was to collect data to support down-selection and development of a primary distillation technology for application in a lunar outpost water recovery system. The CDS portion of the comparison test was conducted between May 6 and August 19, 2009. The system was challenged with two pretreated test solutions, each intended to represent a feasible wastewater generated in a surface habitat. The 30-day equivalent wastewater loading volume for a crew of four was intended to be processed for each wastewater solution. Test Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. Test Solution 2 contained the addition of human-generated hygiene wastewater to the solution 1 waste stream components. Approximately 1500 kg of total wastewater was processed through the CDS during testing. Respective recoveries per solution were 93.4 +/- 0.7 and 90.3 +/- 0.5 percent. The average specific energy of the system during testing was calculated to be less than 120 W-hr/kg. The following paper provides detailed information and data on the performance of the CDS as challenged per the ELS distillation comparison test.

Dry-distillation of experimental animal wastes containing radioisotopes

International Nuclear Information System (INIS)

Miyatake, Hideo; Saito, Kazumi; Kurihara, Norio

1988-01-01

Mice were dry-distilled at 800deg C for 10 min, after [ 32 P]orthophosphate or L-[4,5- 3 H]leucine was intraperitoneally administered. Phosphorus-32 was quantitatively recovered in the residual solid, whereas 95% of 3 H was found in the distillate (condensed water). When 14 C (L-[U- 14 C]malic acid or L-[U- 14 C]leucine) was administered to mice and they were dry-distilled, 14 C-radioactivity was distributed into two fractions; residual solid and exhaust gas. In these cases, the recovery percentage of 14 C in residual solid was not very high but increased as the treating temperature decreased. It reached about 40% of the administered 14 C at 400deg C for 120 min. By the dry-distillation of animals, their weight was reduced to about 10% in every animal tested (mice, rats and rabbits). The volume was reduced to about 20% in cases of mice and rats, and about 30% in case of rabbits. It was concluded that the dry-distillation can be useful as a pre-treatment for disposal of animal wastes containing radioisotopes. (author)

27 CFR 27.40 - Distilled spirits.

Science.gov (United States)

2010-04-01

... OF THE TREASURY LIQUORS IMPORTATION OF DISTILLED SPIRITS, WINES, AND BEER Tax On Imported Distilled Spirits, Wines, and Beer Distilled Spirits § 27.40 Distilled spirits. (a) A tax is imposed on all... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Distilled spirits. 27.40...

PARAFFIN SEPARATION VACUUM DISTILLATION

Directory of Open Access Journals (Sweden)

Zaid A. Abdulrahman

2013-05-01

Full Text Available Simulated column performance curves were constructed for existing paraffin separation vacuum distillation column in LAB plant (Arab Detergent Company/Baiji-Iraq. The variables considered in this study are the thermodynamic model option, top vacuum pressure, top and bottom temperatures, feed temperature, feed composition & reflux ratio. Also simulated columns profiles for the temperature, vapor & liquid flow rates composition were constructed. Four different thermodynamic model options (SRK, TSRK, PR, and ESSO were used, affecting the results within 1-25% variation for the most cases.The simulated results show that about 2% to 8 % of paraffin (C10, C11, C12, & C13 present at the bottom stream which may cause a problem in the LAB plant. The major variations were noticed for the top temperature & the  paraffin weight fractions at bottom section with top vacuum pressure. The bottom temperature above 240 oC is not recommended because the total bottom flow rate decreases sharply, where as  the weight fraction of paraffins decrease slightly. The study gives evidence about a successful simulation with CHEMCAD

Distillation of oil-bearing minerals

Energy Technology Data Exchange (ETDEWEB)

1952-12-03

A process of distilling oil-bearing minerals of the type of oil shale which disintegrate during distillation consists of subjecting the subdivided minerals to a distillation temperature in the form of a highly turbulent dense mass fluidized by an upwardly flowing gasiform medium in a distillation zone and supplying the heat required for the distillation by burning solid distillation residue with a combustion-supporting gas in the form of a fluidized mass of solids in a separate combustion zone at a combustion temperature and returning solid combustion residue substantially at the combustion temperature to the distillation zone. Combustion temperature is positively maintained at a figure not exceeding 1,200/sup 0/F and at a figure which is not substantially more than 50/sup 0/F higher than the distillation temperature.

Determination of 129I using distillation method and liquid scintillation spectrometry

International Nuclear Information System (INIS)

Horvathova, B.; Dulanska, S.; Remenec, B.; Matel, L.; Gardonova, V.

2014-01-01

The conditions for effective distillation of iodine as a screening method for the determination of 129 I by liquid scintillation spectrometry were optimized. By distillation of iodine it is possible to achieve high-purity fraction without interferences needed for measuring 129 I for liquid scintillation spectrometer. Yields of separation were determined gravimetrically using PdI 2 ·H 2 O. The environment that was found to be effective for distillation of iodine is made up of 1 - 2 mol dm -3 HNO 3 together with 0.4 g of NaNO 2 as an oxidizing agent (I . →I 2 ). For testing of distillation, suitable apparatus for distillation of iodine was designed. The apparatus was connected to a vacuum box, which sucks iodine of the distilled solution. Then the iodine was captured in a solution of NaOH at a concentration of 1.5 mol dm -3 . As part of the optimization methodology, it was found that the concentration of NaOH solution for adsorption I 2 (g) does not have any influence on the yields, as opposed to its volume, where it is necessary to use a maximum amount of NaOH in the holding flask for maximum adsorption of iodine. It was determined, that time needed for coagulation PdI 2 ·H 2 O is 24 hours and suitable time for distillation was 20 minutes. Optimized method for the determination of 129 I was applied for various matrices from NPPs in Slovak Republic. Values of 129 I for all analyzed samples were less than the minimum detectable activity (0.043 Bq). The separation yields were in the range (73.14 to 82.04)% and 129 I was measured on a liquid scintillation spectrometer TRI CARB 2900TR with high detection efficiency of 95%. (authors)

Experimental demonstration of fractional-order oscillators of orders 2.6 and 2.7

KAUST Repository

Elwakil, A.S.; Agambayev, Agamyrat; Allagui, A.; Salama, Khaled N.

2017-01-01

The purpose of this work is to provide an experimental demonstration for the development of sinusoidal oscillations in a fractional-order Hartley-like oscillator. Solid-state fractional-order electric double-layer capacitors were first fabricated using graphene-percolated P(VDF-TrFE-CFE) composite structure, and then characterized by using electrochemical impedance spectroscopy. The devices exhibit the fractional orders of 0.6 and 0.74 respectively (using the model Zc=Rs+1/(jω)αCα), with the corresponding pseudocapacitances of approximately 93nFsec−0.4 and 1.5nFsec−0.26 over the frequency range 200kHz–6MHz (Rs < 15Ω). Then, we verified using these fractional-order devices integrated in a Hartley-like circuit that the fractional-order oscillatory behaviors are of orders 2.6 and 2.74.

Experimental demonstration of fractional-order oscillators of orders 2.6 and 2.7

KAUST Repository

Elwakil, A.S.

2017-02-07

The purpose of this work is to provide an experimental demonstration for the development of sinusoidal oscillations in a fractional-order Hartley-like oscillator. Solid-state fractional-order electric double-layer capacitors were first fabricated using graphene-percolated P(VDF-TrFE-CFE) composite structure, and then characterized by using electrochemical impedance spectroscopy. The devices exhibit the fractional orders of 0.6 and 0.74 respectively (using the model Zc=Rs+1/(jω)αCα), with the corresponding pseudocapacitances of approximately 93nFsec−0.4 and 1.5nFsec−0.26 over the frequency range 200kHz–6MHz (Rs < 15Ω). Then, we verified using these fractional-order devices integrated in a Hartley-like circuit that the fractional-order oscillatory behaviors are of orders 2.6 and 2.74.

Mise au point d'un nouvel appareil de "distillation isotherme" Disterm Development of Distherm, a New Isothermal Distillation Apparatus

Directory of Open Access Journals (Sweden)

Mouton M.

2006-11-01

Full Text Available Les études analytiques de distillats pétroliers d'intervalles d'ébullition élevés doivent être réalisées sur des produits préparés dans des conditions de distillation extrêmement douces, de manière à conserver intactes toutes les espèces chimiques initialement contenues dans le pétrole brut en l'état. Pour répondre à cet objectif, le Comité de Distillation du GEC (Groupe d'Études Concertées sur l'analyse des fractions lourdes du pétrole, réunissant Compagnie Francaise de Raffinage (CFR, Société Nationale Elf Aquitaine (SNEA et Institut Français du Pétrole (IFP a mis au point un schéma de préparation spécial de ces distillats, faisant appel à des techniques de distillation continue, de type « isotherme» et « moléculaire ». Dans ce cadre, le Comité de Distillation du GEC a été amené à développer un nouvel appareillage de distillation x isotherme », permettant de réduire, sans craquage, tout pétrole brut jusqu'à une température maximale comprise entre 350 et 380 °C. On décrit dans cet article ce nouvel ensemble de distillation, ainsi que ses conditions opératoires de fonctionnement. On y donne aussi un aperçu de la précision de la méthode de distillation réalisable avec cet appareil, ainsi que de la qualité de fractionnement obtenu.Enfin, à l'aide de quelques exemples particuliers, on montre que le domaine d'application de l'appareil peut être étendu à des produits autres que des pétroles bruts. Analytical examinations of high-boiling-range petroleum distillates must be made with products prepared under extremely mild distillation conditions so as ta maintain intact all the chemical species initially present in the original crude oil.

Hydrocracking of atmospheric distillable residue of Mongolian oil

Directory of Open Access Journals (Sweden)

Ts Tugsuu

2014-09-01

Full Text Available Many catalytic processes to refine heavy part of crude oil have attracted much interest due to declining reserves of light crude oils. This study focused on hydrocracking process of atmospheric distillable residue of Mongolian crude oil in the first time compared to those of other countries. Residue samples were hydrocracked with a commercial catalyst at 450°C, 460°C, 470°C for 2 h under hydrogen pressure of 10 MPa. The amount of residual fraction (350°Cdistillable residue from Tamsagbulag crude oil. When the ME-AR was hydrocracked, the high consumption of hydrogen was related to the lowest H/C atomic ratio of feed atmospheric residue. The amount of liquid fractions (BP<350°C including gaseous products increased from 45.4wt% to 89.2wt%, when the reaction temperature increased from 450°C to 470°C. The highest yield of the middle fraction for each sample was observed at temperature of 460°C. On the other hand, the effect of temperature on the yield of middle fraction was not so high as compared with the yields of other fractions. The contents of n-paraffins on midlle and heavy fractions of TB-AR, DQ-AR were similar, but ME-AR’s was around 2 times lower than other after hydrocracking runs.DOI: http://dx.doi.org/10.5564/mjc.v12i0.166 Mongolian Journal of Chemistry Vol.12 2011: 24-28 

Chemical profile of sugarcane spirits produced by double distillation methodologies in rectifying still

Directory of Open Access Journals (Sweden)

André Ricardo Alcarde

2011-06-01

Full Text Available The objective of this study was to determine the chemical profile of sugarcane spirits produced by different double distillation methodologies in rectifying still. Fermented sugarcane juice was distilled in rectifying still according to three double distillation methodologies: the methodology used for cognac production; the methodology used for whisky production; and the 10-80-10 percentage composition methodology, referring to the volumes of head, heart and tail of the distillate fractions from the second distillation. For comparison purposes, a simple distilled spirit was also produced. The distillates were analyzed for concentrations of ethanol, copper, volatile acidity, furfural and hydroxymethylfurfural, aldehydes, esters, methanol and higher alcohols. The spirits were also evaluated on the sensory attributes of aroma, taste and preference. Compared to simple distillation, double distillation improved the chemical quality of the spirits, since it has reduced the concentrations of acids, aldehydes, esters, methanol, higher alcohols and, consequently, their coefficient of congeners. Regardless of the methodology employed, the double distillation improved the sensory quality of the spirits since they obtained higher sensory acceptance in relation to spirits produced by simple distillation. Among double distilled spirits, the one produced according to whisky methodology obtained the best scores from appraisers on the aroma and flavor parameters and it was also the most preferred.

Infrared spectrophotometry, a rapid and effective tool for characterization of direct distillation naphthas

International Nuclear Information System (INIS)

Baldrich Ferrer, Carlos A; Novoa Mantilla, Luz Angela

2005-01-01

The characterization of naphtha obtained by direct distillation of medium and heavy crude oils is often limited by the low yield of these fractions. Gas chromatography is a technique that allows a complete determination of the chemical composition of this fraction. However, the prediction of properties such as octane rating and RVP from chromatographic data is a difficult task because there are not adequate models to predict the interaction of the different components, and particularly in the case of heavier fractions, there are some problems for the complete separation of components under the gas chromatographic conditions. The IR technology constitutes a rapid and effective tool to predict several properties of naphtha from the correlation of the spectrum in the infrared area and the properties. In this study, prediction models were developed in a Petrospec Cetane 2000 analyzer, in order to predict in a fast and simple way, the density, the antiknock index and the aromatic content of straight run naphtha obtained in a standard crude oil distillation unit. The equipment used was designed in the factory for the exclusive characterization of medium distillation and not for lighter fractions therefore this work constitutes an innovation given the extensive applications of this type of analyzers

Batch distillation column modeling for quality control program

NARCIS (Netherlands)

Betlem, Bernardus H.L.

2000-01-01

For batch distillation, the dynamic composition behaviour can be described by the dominant time constant and the bottom exhaustion. Its magnitude is determined by the change of the composition distribution and is maximal when the inflection point of the molar fraction profile is located in the

Design and construction of a Fresnel linear distiller

International Nuclear Information System (INIS)

Saettone, E.

2014-01-01

It was designed a Fresnel linear distiller based on optical calculations obtained from taking into account Lima's latitude value, Earth inclination angle and heat absorber cavity's dimensions. The 5.6 m 2 reflective surface concentrator of the distiller was constructed with 32 plane rectangular mirrors; the heat absorber cavity was made with a rectangular blackened aluminum tube 1 m long and installed 2.5 m over the plane of mirrors. The Fresnel linear distiller was installed at the University of Lima and experimental tests were performed during no cloudy summer days. There were measured ambient temperature, heat absorber cavity temperature, radiant flux and fresh water volume. From this, it was obtained a production of 0.89 liters/hour and 0.79 L/m 2 , and it was calculated a total performance of 34.5% in desalting sea water. Finally, it is presented a comparison between Fresnel linear distiller (FLD) and parabolic trough distiller (PTD) with similar dimensions and characteristics. It is obtained that the last one produced almost 32% more fresh water than the former, but at the same time, the FLD is almost 20% cheaper than PTD. However, water cost production with both distillers using is almost the same. (author)

¹³⁶ Xe enrichment through cryogenic distillation

Energy Technology Data Exchange (ETDEWEB)

Back, Henning O.; Bottenus, Daniel R.; Clayton, Christopher K.; Stephenson, David E.; TeGrotenhuis, Ward E.

2017-09-01

The next generation of 136Xe neutrinoless double beta decay experiments will require on the order of 5 tons of enriched 136Xe. By estimating the relative volatilities of the xenon isotopes and using standard chemical engineering techniques we explore the feasibility of using cryogenic distillation to produce 5 tons of 80% enriched 136Xe in 5-6 years. With current state-of-the-art distillation column packing materials we can estimate the total height of a traditional cryogenic distillation column. We also, report on how Micro Channel Distillation may reduce the overall size of a distillation system for 136Xe production.

Characteristics of Wet and Dried Distillers Grains on Ruminal Fermentation and Effects of Dietary Wet Distillers Grains on Performance of Hanwoo Steers

Directory of Open Access Journals (Sweden)

Ill Young Kim

2015-05-01

Full Text Available Two experiments were conducted to evaluate the nutrient composition, in vitro dry matter disappearance (IVDMD and organic matter disappearance (IVOMD of three kinds of distillers grains (DG; i wet distillers grains (WDG, KRW 25/kg, ii dried distillers grains (DDG, KRW 280/kg, iii dried distillers grains with solubles (DDGS, KRW 270/kg produced from tapioca 70% and rice 30%, and to evaluate dietary effects of WDG on the performance of Hanwoo steers. In Exp. 1, twelve-WDG, four-DDG and one-DDGS were collected from seven ethanol plants. Average crude protein, crude fiber, neutral detergent fiber, and acid detergent fiber of WDG, DDG, and DDGS were: 32.6%, 17.8%, 57.5%, and 30.2% for WDG, 36.7%, 13.9%, 51.4%, and 30.5% for DDG, and 31.0%, 11.9%, 40.3%, and 21.2% for DDGS (DM basis, respectively. The DDGS had a higher quantity of water-soluble fraction than WDG and DDG and showed the highest IVDMD (p<0.05 in comparison to others during the whole experimental time. The IVDMD at 0 to 12 h incubation were higher (p<0.05 in DDG than WDG, but did not show significant differences from 24 to 72 h. The same tendency was observed in IVOMD, showing that DG made from tapioca and rice (7:3 can be used as a feed ingredient for ruminants. Considering the price, WDG is a more useful feed ingredient than DDG and DDGS. In Exp. 2, 36 Hanwoo steers of 21 months (495.1±91 kg were randomly assigned to one of three dietary treatments for 85 days; i Control (total mixed ration, TMR, ii WDG 10% (TMR containing 10% of WDG, as fed basis, and iii WDG 20% (TMR containing 20% of WDG, as fed basis. With respect to body weight and average daily gain, there were no differences between control and WDG treatments during the whole experimental period. Dry matter intake of control (9.34 kg, WDG 10% (9.21 kg and 20% (8.86 kg and feed conversion ratio of control (13.0, WDG 10% (13.2 and 20% (12.1 did not show differences between control and WDG treatments. Thus, the use of WDG up to 20

Distillation methods

International Nuclear Information System (INIS)

Konecny, C.

1975-01-01

Two main methods of separation using the distillation method are given and evaluated, namely evaporation and distillation in carrier gas flow. Two basic apparatus are described for illustrating the methods used. The use of the distillation method in radiochemistry is documented by a number of examples of the separation of elements in elemental state, volatile halogenides and oxides. Tables give a survey of distillation methods used for the separation of the individual elements and give conditions under which this separation takes place. The suitability of the use of distillation methods in radiochemistry is discussed with regard to other separation methods. (L.K.)

Conceptual design of heterogeneous azeotropic distillation process for ethanol dehydration using 1-butanol as entrainer

Directory of Open Access Journals (Sweden)

Paritta Prayoonyong

2014-12-01

Full Text Available The synthesis of a heterogeneous azeotropic distillation process for ethanol dehydration using 1-butanol as entrainer is presented. The residue curve map of the ethanol/water/1-butanol mixture is computationally generated using non-random twoliquid thermodynamic model. It is found that 1-butanol leads to a residue curve map topological structure different from that generated by typical entrainers used in ethanol dehydration. Synthesised by residue curve map analysis, the distillation flowsheet for ethanol dehydration by 1-butanol comprises a double-feed column integrated with an overhead decanter and a simple column. The double-feed column is used to recover water as the top product, whereas the simple column is used for recovering ethanol and 1-butanol. The separation feasibility and the economically near-optimal designs of distillation columns in the flowsheet are evaluated and identified by using the boundary value design method. The distillation flowsheet using 1-butanol is compared with the conventional process using benzene as entrainer. Based on their total annualised costs, the ethanol dehydration process using 1-butanol is less economically attractive than the process using benzene. However, 1-butanol is less toxic than benzene.

Determination of methanol in Iranian herbal distillates.

Science.gov (United States)

Shirani, Kobra; Hassani, Faezeh Vahdati; Azar-Khiavi, Kamal Razavi; Moghaddam, Zohreh Samie; Karimi, Gholamreza

2016-06-01

Herbal distillates have been used as beverages, for flavoring, or as phytomedicines in many countries for a long time. Recently, the occurrence of blindness after drinking herbal distillates has created concerns in Iran. The aim of this study was to determine the concentrations of methanol in herbal distillates produced in Iran. Eighty-four most commonly used herbal distillates purchased from herbal distillate factories were analyzed for methanol contents by gas chromatography and flame ionization detection, with ethanol as internal standard. In 15 herbal distillates, the methanol concentration was below the limit of quantitation. The methanol concentrations in all samples ranged from 43 to 277 mg/L. Forty-five samples contained methanol in excess of the Iranian standard. The maximum concentration was found in an herbal distillate of Mentha piperita (factory E) (277±12), and the minimum in a distillate of Carum carvi (factory B) (42.6 ± 0.5). Since the 45 Iranian herbal distillates containing methanol levels were beyond the legal limits according to the Iranian standard, it seems necessary to monitor the amount of methanol and give a warning to watch out for the latent risk problem of methanol uptake, and establish a definitive relationship between the degree of intoxication observed and the accumulation of methanol in the blood.

Some remarks on the carrier distillation method; Quelques remarques sur la methode 'carrier distillation'

Energy Technology Data Exchange (ETDEWEB)

Avni, R; Chaput, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-07-01

The method described by SCRIBNER and MULLIN makes possible the spectrographic analysis of the refractory oxides of uranium and plutonium. It uses a distillation of the elements which is more or less selective. The influence of the carrier is the subject of as many hypotheses as there are parameters involved in the process. The measurements of the arc temperature carried out on the leading edges of the vibration bands and of certain copper lines have made it possible to show the influence of the nature of the carrier and to establish a relationship between the values of the excitation potentials of the atoms and the temperatures produced. Further, this result makes it possible to explain certain contradictions between the principle of a fractional distillation in the arc which is incompatible with the refractory properties of certain elements and their spectrographic sensitivity. (author) [French] La methode decrite par SCRIBNER et MULLIN permet l'analyse spectrographique des oxydes refractaires d'uranium et de plutonium. Elle fait appel a une distillation plus ou moins selective des elements. L'influence de l'entraineur est l'objet d'aussi nombreuses hypotheses que les parametres lies au phenomene. Les mesures de la temperature de l'arc, effectuees sur les tetes de bandes de vibration du cyanogene et certaines raies du cuivre ont permis de montrer l'influence de la nature de l'entraineur et de trouver une relation entre les valeurs des potentiels d'excitation des atomes et les temperatures produites. En outre, ce resultat permet d'expliquer certaines contradictions entre le principe d'une distillation fractionnee dans l'arc incompatible avec les proprietes refractaires de certains elements et leur sensibilite spectrographique. (auteur)

Determination of volatile compounds in grape distillates by solid-phase extraction and gas chromatography.

Science.gov (United States)

Lukić, Igor; Banović, Mara; Persurić, Dordano; Radeka, Sanja; Sladonja, Barbara

2006-01-06

Solid-phase extraction (SPE) procedure on octadecylsilica (C18) was developed for accumulation of volatile compounds from grape distillates. The procedure was optimised for final analysis by capillary gas chromatography. At mass concentrations in model solutions ranging from 0.1 to 50 mg/l solid-phase extraction recoveries of all analytes ranged from 69% for 2-phenylethanol to 102% for capric acid, with RSD values from 2 to 9%. SPE recoveries of internal standards to be added in the sample solution prior to extraction, higher alcohols 2-ethyl-1-hexanol and 1-undecanol, were 97 and 93%, respectively, with RSD values of 3%. Detection limits of analyzed compounds in model solutions ranged from 0.011 mg/l for isoamyl acetate to 0.037 mg/l for caproic acid. Method efficiency was tested in relation to acetic acid content, volume fraction of ethanol and possible matrix effects. A significant influence of matrix on SPE efficiency for geraniol, cis-2-hexen-1-ol and cis-3-hexen-1-ol was detected. For the same reason, 2-phenylethanol could not be determined by developed SPE method in samples of grape distillates. The developed solid-phase extraction method was successfully applied to determine the differences in volatile compound content in different grape distillates produced by the distillation of crushed, pressed and fermented grapes.

Thermodynamic analysis of 6xxx series Al alloys: Phase fraction diagrams

Directory of Open Access Journals (Sweden)

Cui S.

2018-01-01

Full Text Available Microstructural evolution of 6xxx Al alloys during various metallurgical processes was analyzed using accurate thermodynamic database. Phase fractions of all the possible precipitate phases which can form in the as-cast and equilibrium states of the Al-Mg-Si-Cu-Fe-Mn-Cr alloys were calculated over the technically useful composition range. The influence of minor elements such as Cu, Fe, Mn, and Cr on the amount of each type of precipitate in the as-cast and equilibrium conditions were analyzed. Phase fraction diagrams at 500 °C were mapped in the composition range of 0-1.1 wt.% Mg and 0-0.7 wt.% Si to investigate the as-homogenized microstructure. In addition, phase fraction diagram of Mg2Si at 177 °C was mapped to understand the microstructure after final annealing of 6xxx Al alloy. Based on the calculated diagrams, the design strategy of 6xxx Al alloy to produce highest strength due to Mg2Si is discussed.

27 CFR 19.322 - Distillates containing extraneous substances.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Distillates containing... Distillates containing extraneous substances. (a) Use in production. Distillates containing substantial... produced. Distillates removed from the distilling system under the provisions of this paragraph shall be...

Process of distilling heavy hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1929-12-03

This invention has for its object the distillation of heavy liquid hydrocarbons for the purpose of obtaining lighter hydrocarbons stable and immediately salable for fuels in combustion motors. The process is distinguished by the fact that the heavy hydrocarbon is distilled by means of heating to a temperature in keeping with the nature of the material to be treated up to 350/sup 0/C under pressure or without pressure the distillation being carried out on catalysts containing successively nickel, copper, and iron (3 parts of nickel, 1 part of copper, and 1 part of iron), the vapors produced by this distillation being exposed in turn to the action of catalysts of the same nature and in the same proportion.

Hydrodeoxygenation of oxidized distilled bio-oil for the production of gasoline fuel type

International Nuclear Information System (INIS)

Luo, Yan; Guda, Vamshi Krishna; Hassan, El Barbary; Steele, Philip H.; Mitchell, Brian; Yu, Fei

2016-01-01

Highlights: • Oxidation had more influence on the yield of total hydrocarbons than distillation. • The highest total hydrocarbon yield was obtained from oxidized distilled bio-oil. • The 2nd-stage hydrocarbons were in the range of gasoline fuel boiling points. • The main products for upgrading of oxidized bio-oil were aliphatic hydrocarbons. • The main products for upgrading of non-oxidized bio-oil were aromatic hydrocarbons. - Abstract: Distilled and oxidized distilled bio-oils were subjected to 1st-stage mild hydrodeoxygenation and 2nd-stage full hydrodeoxygenation using nickel/silica–alumina catalyst as a means to enhance hydrocarbon yield. Raw bio-oil was treated for hydrodeoxygenation as a control to which to compare study treatments. Following two-stage hydrodeoxygenation, four types of hydrocarbons were mainly comprised of gasoline and had water contents, oxygen contents and total acid numbers of nearly zero and higher heating values of 44–45 MJ/kg. Total hydrocarbon yields for raw bio-oil, oxidized raw bio-oil, distilled bio-oil and oxidized distilled bio-oil were 11.6, 16.2, 12.9 and 20.5 wt.%, respectively. The results indicated that oxidation had the most influence on increasing the yield of gasoline fuel type followed by distillation. Gas chromatography/mass spectrometry characterization showed that 66.0–76.6% of aliphatic hydrocarbons and 19.5–31.6% of aromatic hydrocarbons were the main products for oxidized bio-oils while 35.5–38.7% of aliphatic hydrocarbons and 58.2–63.1% of aromatic hydrocarbons were the main products for non-oxidized bio-oils. Both aliphatic and aromatic hydrocarbons are important components for liquid transportation fuels and chemical products.

40 CFR 1065.703 - Distillate diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Distillate diesel fuel. 1065.703... Standards § 1065.703 Distillate diesel fuel. (a) Distillate diesel fuels for testing must be clean and... distillate diesel fuels: (1) Cetane improver. (2) Metal deactivator. (3) Antioxidant, dehazer. (4) Rust...

Dry distillation

Energy Technology Data Exchange (ETDEWEB)

1939-11-30

To heat rapidly, and prevent agglutination of carbonaceous material duriing distillation of shale, a furnace of the tunnel type has four compartments (the preheating chamber, the distillation chamber proper, and two cooling chambers). Waggons, which convey the material through the distilling chamber, have perforated bottoms. Above the waggons in the distilling chamber are three heating sections having pipes which pass through the sections and communicate with the distilling chamber. Fans cause the distillation gases to circulate through the material and the pipes. The heating gases from three fire boxes are introduced into the oven, and circulate around pipes and are drawn to the discharge apertures by the fans. The heating gases introduced at two points travel in the direction of the material being treated, while the gases introduced at a third point travel in counter flow thereto. Gas is discharged by two pipes. Trucks carrying treated material are passed to two cooling chambers.

Evaluation of the effects of active fractions of chinese medicine formulas on IL-1β, IL-6, and TNF-α release from ANA-1 murine macrophages.

Science.gov (United States)

Ni, Li-Jun; Wang, Nan-Nan; Zhang, Li-Guo; Guo, Yan-Zi; Shi, Wan-Zhong

2016-02-17

Yaotongning (YTN) is a traditional Chinese Medicine (TCM) that contains ten component medicinal materials (CMMs) and uses Chinese rice wine as a vehicle to enhance its efficacy. YTN has been used for rheumatoid arthritis (RA) treatment in China for decades and has been reported to have anti-inflammatory and analgesic effects, as well as to strengthen the immune system. The present work quantitatively evaluated the in vitro effects of active fractions from the ten CMMs that make up YTN and eight additional herbs commonly used in TCM formulas for RA treatment, as well as different combinations of these active fractions, on cellular immune response; the findings were used to determine which active fractions are responsible for promoting an immune response, and to assess whether YTN is superior to other similar formulas and whether YTN can be improved by simplifying its formula from the point of its cellular immunomodulatory activity. Using the YTN formulation principles and some concepts in combinatorial chemistry, 27 TCM samples were designed by combining some or all of the active fractions of YTN and other eight herbs used for RA treatment. Release of interleukin-1β (IL-1β), interleukin-6 (IL-6), and tumor necrosis factor-alpha (TNF-α) from ANA-1 murine macrophages was measured using an enzyme-linked immunosorbent assay (ELISA). The immunoregulatory effects of the TCM samples were evaluated by comparing their half-effective concentrations (EC50) for stimulating the release of these cytokines. Among the investigated active fractions, the flavonoids from Carthamus tinctorius (Fct), Davallia mariesii (Fdm), and Cinnamomum cassia Twig volatile oils (Vca) from the eight selected herbs effectively promoted IL-1β and IL-6 release from ANA-1 cells. Saponins from the YTN CMM Glycyrrhiza uralensis (Sgu) were the most potent promoters of IL-1β and TNF-α release. The aqueous extract of YTN CMM Eupolyphaga sinensis (Ves) strongly enhanced the release of IL-1β, IL-6, and

SURFACE-ACTIVE PROPERTIES OF THE DISTILLERS GRAINS AND THE PECTINS ISOLATED FROM THEM

Directory of Open Access Journals (Sweden)

N. S. Kaisheva

2016-01-01

Full Text Available Distillers grains are a huge secondary raw material resource, prospective for different fields, including pharmaceutical use, because of a rich content of biologically active compounds. The purpose of this paper was to estimate possibilities of the pharmaceutical use of distillers grains as the additive agent by means of surface-active properties of distillers grains study as well as pectins, isolated from them. We have established the surface-active properties of the liquid phase of the distillers wheat grains by means of higher pressure of air bubbles with the use of Rehbinder’s apparatus. It contained 6.67 mol/m3 pectins, and pectins isolated from a solid phase of the same distillers grains: surface activity 11.67 and 7.54, saturated surface excess amounted to 1.28×10-5 and 6.25×10-5 mol/m2, critical concentration of micelle formation amounted to 1.32 mol/m3 and 1.48 mol/m3 respectively. Surface-active characteristics of distillers grains and isolated pectins are comparable with well-known natural polysaccharides (sodium alginate, polygalacturonic acid, beet bin pectin, which are used as additive agents in technology of medicinal plants. We have determined the sizes of pectins molecules from distillers grains in the unsaturated adsorption layers, which differed from the well-known polysaccharides by lesser square (2.658 Å2, radius (0.920 Å, diameter of cross-section (1.840 Å and the volume (2727 Å3 at the bigger mass per surface unit (1.031×10-4 кг and a length (1026 Å. The data obtained by the sizes of pectin molecules are the favorable factor, which conduced their high biological availability. 

Comparative acute toxicity of shale and petroleum derived distillates.

Science.gov (United States)

Clark, C R; Ferguson, P W; Katchen, M A; Dennis, M W; Craig, D K

1989-12-01

In anticipation of the commercialization of its shale oil retorting and upgrading process, Unocal Corp. conducted a testing program aimed at better defining potential health impacts of a shale industry. Acute toxicity studies using rats and rabbits compared the effects of naphtha, Jet-A, JP-4, diesel and "residual" distillate fractions of both petroleum derived crude oils and hydrotreated shale oil. No differences in the acute oral (greater than 5 g/kg LD50) and dermal (greater than 2 g/kg LD50) toxicities were noted between the shale and petroleum derived distillates and none of the samples were more than mildly irritating to the eyes. Shale and petroleum products caused similar degrees of mild to moderate skin irritation. None of the materials produced sensitization reactions. The LC50 after acute inhalation exposure to Jet-A, shale naphtha, (greater than 5 mg/L) and JP-4 distillate fractions of petroleum and shale oils was greater than 5 mg/L. The LC50 of petroleum naphtha (greater than 4.8 mg/L) and raw shale oil (greater than 3.95 mg/L) also indicated low toxicity. Results demonstrate that shale oil products are of low acute toxicity, mild to moderately irritating and similar to their petroleum counterparts. The results further demonstrate that hydrotreatment reduces the irritancy of raw shale oil.

Development for a procedure for the determination of 2-phenylethanol in Hellenic wine distillates (Vitis vinifera L. and their changes during distillation

Directory of Open Access Journals (Sweden)

Maria Gerogiannaki-Christopoulou

2009-09-01

Significant and impact study: The knowledge of the impact of the commercial fining agent in 2-phenylethanol content during the distillation in different fractions is important for monovarietal wine spirits in order to produce qualified wine brandies. This study is also particular important for brandies production in commercial distilleries in order to separate at the right alcoholic strenght and to take fractions with the higher concentration of this alcohol which in combination of course with the minor and major other congeners gives an qualified organoleptic character.

Effect of an electron beam on the subsequent pyrogenic distillation of lignin and cellulose

International Nuclear Information System (INIS)

Metreveli, P.K.; Metreveli, A.K.; Kholodkova, E.M.; Ponomarev, A.V.

2014-01-01

The irradiation notably influences responsiveness of cellulose and lignin to the subsequent pyrogenic distillation though both weight and the form of samples do not change almost at doses up to 3 MGy. Decreases in overpoint of lignin and cellulose irradiated at 2.2 MGy are ∼80°and ∼100°, respectively. Third of condensate from cellulose and almost half from lignin are distilled-off at lower temperatures. The thermally instable compounds convertible mainly to furans via subsequent heating are forming in cellulose. Distillation of the irradiated lignin gives less tar which, however, is richer by methoxy-phenols. In distilled-off water–organic fraction the content of soluble organic compounds is increased. - Highlights: • Irradiation facilitates subsequent dry distillation of cellulose and lignin. • Overpoints of irradiated samples are decreasing. • Furans and methoxy-phenols formation improves

Aspirin-Induced Gastric Lesions Alters EGFR and PECAM-1 Immunoreactivity in Wistar Rats: Modulatory Action of Flavonoid Fraction of Musa Paradisiaca.

Science.gov (United States)

Alese, Margaret Olutayo; Adewole, Stephen Olarinde; Akinwunmi, Kemi Feyisayo; Omonisi, Abidemi Emmanuel; Alese, Oluwole Ojo

2017-08-15

In this study, Epithelial Growth Factor Receptor and Platelet Endothelial Cell Adhesion Molecule-1 were localised to investigate the healing effects of a flavonoid-rich fraction of M. paradisiaca fruit in the gastric corpus of Wistar rats following aspirin-induced gastric lesion. Mature, unripe fruits of M. paradisiaca were peeled; air dried, pulverised, extracted with 70% methanol, concentrated and partitioned. Ninety male Wistar rats were randomly assigned into 6 groups of 15 rats each. The gastric lesion was induced in groups B, C, D, E and F rats by administration of 400 mg/kg aspirin in distilled water. Group A received distilled water. After 24 hours, flavonoid fraction of M. paradisiaca was administered to groups C, D and E at 100, 200 and 400 mg/kg respectively for 21 days. Group F rats received omeprazole at 1.8 mg/kg for 21 days. Five rats from each group were anaesthetized with ketamine on days 14, 21 and 28. Gastric tissues were excised and fixed in Neutral buffered formalin. This was followed by paraffin wax embedding method and sections stained with haematoxylin and eosin and for immunolocalisation of EGFR and PECAM-1. Data were analysed using descriptive and inferential statistics. There was a significant difference in the ulcer index in the corpus of control and treated rats throughout the experimental period (p = 0.0001). H&E stained sections showed a gradual restoration of the epithelial lining in the treated groups. Immunohistochemical examination showed that M. paradisiaca significantly increased (p Musa paradisiaca in attenuating the damaging effects of aspirin on the gastric mucosa was observed as there was a significantly increased reactivity for EGFR and PECAM-1 in the gastric corpus in a dose-dependent manner.

Augmentation of a solar still distillate yield via absorber plate coated with black nanoparticles

Directory of Open Access Journals (Sweden)

A.E. Kabeel

2017-12-01

Full Text Available Effects of utilizing nanomaterial on the solar still productivity investigated experimentally. Cuprous oxides (CuO chosen as a nanoparticles material. The nanoparticles added to the black paint of the solar still walls to enhance the solar still performance. Experiments conducted with cuprous oxide nanoparticles weight concentrations ranged from 10% to 40%. It is found that adding nanoparticles to paint increase heat transfer rate and saline water temperature. Solar still productivity of the proposed system is higher than that for the conventional still. Results acquired that utilizing CuO nanoparticles boosted the distillate by 16% and 25% as compared to the conventional solar still (CSS at weight fraction concentration of 10% and 40%, respectively. Payback period of the distillation system for the modified still using CuO nanomaterials is about 96 days, at weight fraction 10%, which is considerable as compared by 89 days for CSS. Keywords: Nanomaterial, Solar still, Distillation, Nanoparticle

Bioactive compounds from palm fatty acid distillate and crude palm oil

Science.gov (United States)

Estiasih, T.; Ahmadi, K.

2018-03-01

Crude palm oil (CPO) and palm fatty acid distillate (PFAD) are rich sources of bioactive compounds. PFAD is a by-product of palm oil refinery that produce palm frying oil. Physical refining of palm oil by deodorization produces palm fatty acid distillate. CPO and PFAD contain some bioactive compounds such as vitamin E (tocopherol and tocotrienols), phytosterol, and squalene. Bioactive compounds of CPO and PFAD are vitamin E, phytosterols, and squalene. Vitamin E of CPO and PFAD mainly comprised of tocotrienols and the remaining is tocopherol. Phytosterols of CPO and PFAD contained beta sitosterol, stigmasterol, and campesterol. Tocotrienols and phytosterols of CPO and PFAD, each can be separated to produce tocotrienol rich fraction and phytosterol rich fraction. Tocotrienol rich fraction from PFAD has both antioxidant and cholesterol lowering properties. Bioactive compounds of PFAD silmultaneously have been proven to improve lipid profile, and have hepatoprotector effect, imunomodulator, antioxidant properties, and lactogenic effect in animal test experiment. It is possible to develop separation of bioactive compounds of CPO and PFAD integratively with the other process that utilizes fatty acid.

Toxicity of petroleum hydrocarbon distillates to soil organisms.

Science.gov (United States)

Cermak, Janet H; Stephenson, Gladys L; Birkholz, Detlef; Wang, Zhendi; Dixon, D George

2010-12-01

Canadian standards for petroleum hydrocarbons in soil are based on four distillate ranges (F1, C6-C10; F2, >C10-C16; F3, >C16-C34; and F4, >C34). Concerns have arisen that the ecological soil contact standards for F3 may be overly conservative. Oil distillates were prepared and characterized, and the toxicity of F3 and two subfractions, F3a (>C16-C23) and F3b (>C23-C34), to earthworms (Eisenia andrei), springtails (Orthonychiurus folsomi), and northern wheatgrass (Elymus lanceolatus), as well as the toxicity of F2 to earthworms, was determined. Clean soil was spiked with individual distillates and measured concentrations were determined for select tests. Results agree with previous studies with these distillates. Reported toxicities of crude and petroleum products to invertebrates were generally comparable to that of F3 and F3a. The decreasing order of toxicity was F3a > F3 > F3b with invertebrates, and F3a > F3b > F3 with plants. The toxicities of F3a and F3b were not sufficiently different to recommend regulating hydrocarbons based on these distillate ranges. The results also suggest that test durations may be insufficient for determining toxicity of higher distillate ranges, and that the selection of species and endpoints may significantly affect interpretation of toxicity test results. Copyright © 2010 SETAC.

Multipartite nonlocality distillation

International Nuclear Information System (INIS)

Hsu, Li-Yi; Wu, Keng-Shuo

2010-01-01

The stronger nonlocality than that allowed in quantum theory can provide an advantage in information processing and computation. Since quantum entanglement is distillable, can nonlocality be distilled in the nonsignalling condition? The answer is positive in the bipartite case. In this article the distillability of the multipartite nonlocality is investigated. We propose a distillation protocol solely exploiting xor operations on output bits. The probability-distribution vectors and matrix are introduced to tackle the correlators. It is shown that only the correlators with extreme values can survive the distillation process. As the main result, the amplified nonlocality cannot maximally violate any Bell-type inequality. Accordingly, a distillability criterion in the postquantum region is proposed.

Volatilization kinetics of secondary compounds from sugarcane spirits during double distillation in rectifying still Cinética de volatilização de componentes secundários da aguardente de cana-de-açúcar durante dupla destilação em alambique retificador

Directory of Open Access Journals (Sweden)

André Ricardo Alcarde

2010-01-01

Full Text Available The qualitative variation of secondary components plays a key role in the aroma and taste of the sugarcane spirit. The objective of this work was to study the volatilization kinetics of secondary components of sugarcane spirits during double distillation process in a rectifying still to verify the cutoff point in ethanol between "head" and "tail" fractions. Fermented sugarcane juice was distilled in rectifying still according to the methodology used for whisky production. Both distillates from first and second distillations were collected in fractions of 500 mL and analyzed for the concentrations of ethanol, copper, volatile acidity, furfural and hydroxymethylfurfural, aldehydes, esters, methanol and higher alcohols. In the first distillation, aldehydes and esters were distilled at the beginning of the distillation, while acetic acid was distilled at the end of the distillation. Methanol was found in the fractions up to almost half of the first distillation. Higher alcohols were distilled during the whole first distillation, but with greater intensity up to the alcoholic degree of 40% v v-1 of the distillate. During the second distillation, aldehydes, esters and methanol were distilled in the first distillate fractions, being collected mainly at alcohol concentrations above 80% v v-1. Acetic acid was distilled in the final distillate fractions, with concentrations in alcohol content below 20% v v-1. Higher alcohols followed a distillation kinetics pattern similar to ethanol, being collected mainly at alcoholic concentrations above 60% v v-1 of the distillate. The presence of copper, furfural and hydroxymethylfurfural was not detected in any fraction of the distillates of the first and second distillation.A variação qualitativa dos componentes secundários é função chave no aroma e sabor da aguardente de cana-de-açúcar. Avaliou-se a cinética de volatilização de componentes secundários da aguardente de cana-de-açúcar ao longo do

FRACTIONATION OF FATTY ACID OMEGA 3, 6 AND 9 FROM SNAIL (Achatina fulica USING COLOUM CHROMATOGRAPHY

Directory of Open Access Journals (Sweden)

Winarto Haryadi

2010-06-01

Full Text Available The extraction of fat from snail has been carried out by Soxhlet extractor with petroleum ether solvent. Fatty product from extraction was transesterificated in BF3/methanol solvent for an hour by reflux procedure, then extracted by n-hexane to produce methyl ester fatty acid. Free water fatty acid methyl ester was analyzed by Gas Chromatography-Mass spectrometer (GC-MS. Fatty acid ester was separated from its fractions use column chromatography in n-hexane, n-hexane:dietil eter (2:1 v/v, dietil eter, aseton, ethanol and methanol. This fractions wer also analized by GC-MS. From GC-MS data sheet can be obtained 5 fractions which details are; fraction 1 contains omega 3: 27.54 %, omega 6: 15.40 % and omega 9: 6.77 %. Fraction 2 contains omega 3: 3.08 %, omega 6: 15.62 % and omega 9: 10.72 %. Fraction 3 contains omega 6: 3.57 %, omega 9: 7.02 % and none omega 3 inside it. Omega 3, 6 and 9 can't be identification in fraction 4 and 5.   Keywords: extraction, transesterification, column chromatography, GC-MS

Quality Evaluation of Agricultural Distillates Using an Electronic Nose

Directory of Open Access Journals (Sweden)

Tomasz Dymerski

2013-11-01

Full Text Available The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing in quality was obtained by barbotage. Interpretation of the results involved three data analysis techniques: principal component analysis, single-linkage cluster analysis and cluster analysis with spheres method. The investigations prove the usefulness of the presented technique in the quality control of agricultural distillates. Optimum measurements conditions were also defined, including volumetric flow rate of carrier gas (15 L/h, thermostat temperature during the barbotage process (15 °C and time of sensor signal acquisition from the onset of the barbotage process (60 s.

Quality evaluation of agricultural distillates using an electronic nose.

Science.gov (United States)

Dymerski, Tomasz; Gębicki, Jacek; Wardencki, Waldemar; Namieśnik, Jacek

2013-11-25

The paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction of the agricultural distillate samples differing in quality was obtained by barbotage. Interpretation of the results involved three data analysis techniques: principal component analysis, single-linkage cluster analysis and cluster analysis with spheres method. The investigations prove the usefulness of the presented technique in the quality control of agricultural distillates. Optimum measurements conditions were also defined, including volumetric flow rate of carrier gas (15 L/h), thermostat temperature during the barbotage process (15 °C) and time of sensor signal acquisition from the onset of the barbotage process (60 s).

Characterization of federated oil fractions used for the PTAC project to study the petroleum fraction-specific toxicity to soils

International Nuclear Information System (INIS)

Wang, Z.; Jokuty, P.; Fingas, M.; Sigouin, L.

2001-01-01

In 1998, the Petroleum Technology Alliance of Canada (PTAC) and the Canadian Association of Petroleum Producers (CAPP) launched an important research project for the oil and gas industry entitled A Fraction-Specific Toxicity and Derivation of Recommended Soil Quality Guidelines for Crude Oil in Agricultural Soils. The objective was to generate useful and relevant data that could be used to develop soil quality guidelines for petroleum hydrocarbon residuals in agricultural soils. The oil used in the study was Federated crude oil which was fractionated into four fractions using a distillation method. The fraction-based approach was used to support ecologically-relevant, risk-based, soil quality criteria for the protection of environmental health. This paper presented the nominal carbon number and boiling point ranges of these fractions and described the distillation procedures for producing the fractions from the Federated crude oil. The paper also presented the detailed chemical characterization results of each distillation fraction. The toxicity of the crude oil mixture to plants and soil invertebrates was also assessed using standardized toxicity tests. Tests were also conducted to assess the toxicity of fractions of the crude oil and the toxic interactions of the fractions responsible for a significant proportion of the toxicity. Phase 2 of the project was designed to determine if hydrocarbon residuals exceeding 1000 μg/g and weathered for short or long periods of time, posed an ecotoxicological risk or impaired soil physical, chemical and biological properties such that productivity of the agricultural soils was compromised. The objectives of phase 2 were to amend differently textured soils in field plots at sites with fresh crude oil and to monitor their toxicity to terrestrial organisms using laboratory-based ecotoxicity tests. The study showed that because of the nature of the chemical composition of hydrocarbons (such as boiling points, nominal carbon range

Production of uranium metal via electrolytic reduction of uranium oxide in molten LiCl and salt distillation

International Nuclear Information System (INIS)

Eun-Young Choi; Chan Yeon Won; Dae-Seung Kang; Sung-Wook Kim; Ju-Sun Cha; Sung-Jai Lee; Wooshin Park; Hun Suk Im; Jin-Mok Hur

2015-01-01

Recovery of metallic uranium has been achieved by electrolytic reduction of uranium oxide in a molten LiCl-Li 2 O electrolyte at 650 deg C, followed by the removal of the residual salt by vacuum distillation at 850 deg C. Four types of stainless steel mesh baskets, with various mesh sizes (325, 1,400 and 2,300 meshes) and either three or five ply layers, were used both as cathodes and to contain the reduced product in the distillation stage. The recovered uranium had a metal fraction greater than 98.8 % and contained no residual salt. (author)

Sensitivity analysis of a light gas oil deep hydrodesulfurization process via catalytic distillation

Energy Technology Data Exchange (ETDEWEB)

Rosales-Quintero, A.; Vargas-Villamil, F.D. [Prog. de Matematicas Aplicadas y Computacion, Instituto Mexicano del Petroleo, Eje Central Lazaro Cardenas 152, Mexico, D.F. 07330 (Mexico); Arce-Medina, E. [Instituto Politecnico Nacional, ESIQIE, Ed. 8 Col. Lindavista, Mexico, D.F. 07738 (Mexico)

2008-01-30

In this work, a sensitivity analysis of a light gas oil deep hydrodesulfurization catalytic distillation column is presented. The aim is to evaluate the effects of various parameters and operating conditions on the organic sulfur compound elimination by using a realistic light gas oil fraction. The hydrocarbons are modeled using pseudocompounds, while the organic sulfur compounds are modeled using model compounds, i.e., dibenzothiophene (DBT) and 4,6-dimethyl dibenzothiophene (4,6-DMDBT). These are among the most refractive sulfur compounds present in the oil fractions. A sensitivity analysis is discussed for the reflux ratio, bottom flow rate, condenser temperature, hydrogen and gas oil feed stages, catalyst loading, the reactive, stripping, and rectifying stages, feed disturbances, and multiple feeds. The results give insight into the qualitative effect of some of the operating variables and disturbances on organic sulfur elimination. In addition, they show that special attention must be given to the bottom flow rate and LGO feed rate control. (author)

Catalytic distillation structure

Science.gov (United States)

Smith, L.A. Jr.

1984-04-17

Catalytic distillation structure is described for use in reaction distillation columns, and provides reaction sites and distillation structure consisting of a catalyst component and a resilient component intimately associated therewith. The resilient component has at least about 70 volume % open space and is present with the catalyst component in an amount such that the catalytic distillation structure consists of at least 10 volume % open space. 10 figs.

Some remarks on the carrier distillation method

International Nuclear Information System (INIS)

Avni, R.; Chaput, M.

1961-01-01

The method described by SCRIBNER and MULLIN makes possible the spectrographic analysis of the refractory oxides of uranium and plutonium. It uses a distillation of the elements which is more or less selective. The influence of the carrier is the subject of as many hypotheses as there are parameters involved in the process. The measurements of the arc temperature carried out on the leading edges of the vibration bands and of certain copper lines have made it possible to show the influence of the nature of the carrier and to establish a relationship between the values of the excitation potentials of the atoms and the temperatures produced. Further, this result makes it possible to explain certain contradictions between the principle of a fractional distillation in the arc which is incompatible with the refractory properties of certain elements and their spectrographic sensitivity. (author) [fr

Distillation of hydrogen isotopes for polarized HD targets

Energy Technology Data Exchange (ETDEWEB)

Ohta, T., E-mail: takeshi@rcnp.osaka-u.ac.jp [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Bouchigny, S. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); CEA LIST, BP6-92265 Fontenay-aux-Roses, CEDEX (France); Didelez, J.-P. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); Fujiwara, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Fukuda, K. [Kansai University of Nursing and Health Sciences, Shizuki Awaji 656-2131 (Japan); Kohri, H.; Kunimatsu, T.; Morisaki, C.; Ono, S. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Rouille, G. [IN2P3, Institut de Physique Nucleaire, F-91406 Orsay (France); Tanaka, M. [Kobe Tokiwa University, Ohtani-cho 2-6-2, Nagata, Kobe 653-0838 (Japan); Ueda, K.; Uraki, M.; Utsuro, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan); Wang, S.Y. [Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China); Department of Physics, National Kaohsiung Normal University, Kaohsiung 824, Taiwan (China); Yosoi, M. [Research Center for Nuclear Physics, Osaka University, Mihogaoka 10-1, Ibaraki, Osaka 567-0047 (Japan)

2012-02-01

We have developed a new cryogenic distillation system to purify Hydrogen-Deuteride (HD) gas for polarized HD targets in LEPS experiments at SPring-8. A small amount of ortho-H{sub 2} ({approx}0.01%) in the HD gas plays an important role in efficiently polarizing the HD target. Since there are 1-5% impurities of H{sub 2} and D{sub 2} in commercially available HD gases, it is necessary to purify the HD gas up to {approx}99.99%. The distillation system is equipped with a cryogenic distillation unit filled with many small stainless steel cells called 'Heli-pack'. The distillation unit consists of a condenser part, a rectification part, and a reboiler part. The unit is kept at the temperature of 17-21 K. The Heli-pack has a large surface area that makes a good contact between gases and liquids. An amount of 5.2 mol of commercial HD gas is fed into the distillation unit. Three trials were carried out to purify the HD gas by changing temperatures (17.5 K and 20.5 K) and gas extraction speeds (1.3 ml/min and 5.2 ml/min). The extracted gas was analyzed using a gas analyzer system combining a quadrupole mass spectrometer with a gas chromatograph. One mol of HD gas with a purity better than 99.99% has been successfully obtained for the first time. The effective NTP (Number of Theoretical Plates), which is an indication of the distillation performances, is obtained to be 37.2{+-}0.6. This value is in good agreement with a designed value of 37.9. The HD target is expected to be efficiently polarized under a well-controlled condition by adding an optimal amount of ortho-H{sub 2} to the purified HD gas.

ALMA Observations of Gas-rich Galaxies in z ∼ 1.6 Galaxy Clusters: Evidence for Higher Gas Fractions in High-density Environments

Energy Technology Data Exchange (ETDEWEB)

Noble, A. G.; McDonald, M. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Muzzin, A. [Department of Physics and Astronomy, York University, 4700 Keele Street, Toronto, ON MJ3 1P3 (Canada); Nantais, J. [Departamento de Ciencias Físicas, Universidad Andres Bello, Fernandez Concha 700, Las Condes 7591538, Santiago, Región Metropolitana (Chile); Rudnick, G. [The University of Kansas, Department of Physics and Astronomy, 1251 Wescoe Hall Drive, Lawrence, KS 66045 (United States); Van Kampen, E.; Manilla-Robles, A. [European Southern Observatory, Karl-Schwarzschild-Strasse 2, D-85748 Garching bei München (Germany); Webb, T. M. A.; Delahaye, A. [Department of Physics, McGill University, 3600 rue University, Montréal, QC H3A 2T8 (Canada); Wilson, G.; DeGroot, A.; Foltz, R. [Department of Physics and Astronomy, University of California, Riverside, CA 92521 (United States); Yee, H. K. C. [Department of Astronomy and Astrophysics, University of Toronto, 50 St. George Street, Toronto, ON M5S 3H4 (Canada); Boone, K.; Hayden, B.; Perlmutter, S. [Department of Physics, University of California Berkeley, 366 LeConte Hall, MC 7300, Berkeley, CA 94720-7300 (United States); Cooper, M. C. [Department of Physics and Astronomy, University of California, Irvine, 4129 Frederick Reines Hall, Irvine, CA 92697 (United States); Demarco, R. [Departamento de Astronomía, Universidad de Concepción, Casilla 160-C, Concepción, Región del Biobío (Chile); Lidman, C., E-mail: noble@mit.edu [Australian Astronomical Observatory, 105 Delhi Road, North Ryde, NSW 2113 (Australia)

2017-06-20

We present ALMA CO (2–1) detections in 11 gas-rich cluster galaxies at z ∼ 1.6, constituting the largest sample of molecular gas measurements in z > 1.5 clusters to date. The observations span three galaxy clusters, derived from the Spitzer Adaptation of the Red-sequence Cluster Survey. We augment the >5 σ detections of the CO (2–1) fluxes with multi-band photometry, yielding stellar masses and infrared-derived star formation rates, to place some of the first constraints on molecular gas properties in z ∼ 1.6 cluster environments. We measure sizable gas reservoirs of 0.5–2 × 10{sup 11} M {sub ☉} in these objects, with high gas fractions ( f {sub gas}) and long depletion timescales ( τ ), averaging 62% and 1.4 Gyr, respectively. We compare our cluster galaxies to the scaling relations of the coeval field, in the context of how gas fractions and depletion timescales vary with respect to the star-forming main sequence. We find that our cluster galaxies lie systematically off the field scaling relations at z = 1.6 toward enhanced gas fractions, at a level of ∼4 σ , but have consistent depletion timescales. Exploiting CO detections in lower-redshift clusters from the literature, we investigate the evolution of the gas fraction in cluster galaxies, finding it to mimic the strong rise with redshift in the field. We emphasize the utility of detecting abundant gas-rich galaxies in high-redshift clusters, deeming them as crucial laboratories for future statistical studies.

Solar power water distillation unit

International Nuclear Information System (INIS)

Hameed, Kamran; Khan, Muhammad Muzammil; Ateeq, Ijlal Shahrukh; Omair, Syed Muhammad; Ahmer, Muhammad; Wajid, Abdul

2013-01-01

Clean drinking water is the basic necessity for every human being, but about 1.1 billion people in the world lacked proper drinking water. There are many different types of water purification processes such as filtration, reverse osmosis, ultraviolet radiation, carbon absorption, but the most reliable processes are distillation and boiling. Water purification, such as distillation, is especially important in regions where water resources or tap water is not suitable for ingesting without boiling or chemical treatment. In design project It treats the water by combining different methods such as Filtration, Distillation and a technique called concentrated solar power (CSP). Distillation is literally the method seen in nature, whereby: the sun heats the water on the earth's surface, the water is turned into a vapor (evaporation) and rises, leaving contaminants behind, to form clouds. As the upper atmosphere drops in temperature the vapors cool and convert back to water to form water. In this project distillation is achieved by using a parabolic mirror which boils water at high temperature. Filtration is done by sand filter and carbon filter. First sand filter catches the sand particles and the carbon filter which has granules of active carbon is used to remove odor dissolved gases from water. This is the Pre-treatment of water. The filtered water is then collected in a water container at a focus of parabolic mirror where distillation process is done. Another important feature of designed project is the solar tracking of a parabolic mirror which increases the efficiency of a parabolic mirror [1],[2].

Weathering Patterns of Ignitable Liquids with the Advanced Distillation Curve Method.

Science.gov (United States)

Bruno, Thomas J; Allen, Samuel

2013-01-01

One can take advantage of the striking similarity of ignitable liquid vaporization (or weathering) patterns and the separation observed during distillation to predict the composition of residual compounds in fire debris. This is done with the advanced distillation curve (ADC) metrology, which separates a complex fluid by distillation into fractions that are sampled, and for which thermodynamically consistent temperatures are measured at atmospheric pressure. The collected sample fractions can be analyzed by any method that is appropriate. Analytical methods we have applied include gas chromatography (with flame ionization, mass spectrometric and sulfur chemiluminescence detection), thin layer chromatography, FTIR, Karl Fischer coulombic titrimetry, refractometry, corrosivity analysis, neutron activation analysis and cold neutron prompt gamma activation analysis. We have applied this method on product streams such as finished fuels (gasoline, diesel fuels, aviation fuels, rocket propellants), crude oils (including a crude oil made from swine manure) and waste oils streams (used automotive and transformer oils). In this paper, we present results on a variety of ignitable liquids that are not commodity fuels, chosen from the Ignitable Liquids Reference Collection (ILRC). These measurements are assembled into a preliminary database. From this selection, we discuss the significance and forensic application of the temperature data grid and the composition explicit data channel of the ADC.

Weathering Patterns of Ignitable Liquids with the Advanced Distillation Curve Method

Science.gov (United States)

Bruno, Thomas J; Allen, Samuel

2013-01-01

One can take advantage of the striking similarity of ignitable liquid vaporization (or weathering) patterns and the separation observed during distillation to predict the composition of residual compounds in fire debris. This is done with the advanced distillation curve (ADC) metrology, which separates a complex fluid by distillation into fractions that are sampled, and for which thermodynamically consistent temperatures are measured at atmospheric pressure. The collected sample fractions can be analyzed by any method that is appropriate. Analytical methods we have applied include gas chromatography (with flame ionization, mass spectrometric and sulfur chemiluminescence detection), thin layer chromatography, FTIR, Karl Fischer coulombic titrimetry, refractometry, corrosivity analysis, neutron activation analysis and cold neutron prompt gamma activation analysis. We have applied this method on product streams such as finished fuels (gasoline, diesel fuels, aviation fuels, rocket propellants), crude oils (including a crude oil made from swine manure) and waste oils streams (used automotive and transformer oils). In this paper, we present results on a variety of ignitable liquids that are not commodity fuels, chosen from the Ignitable Liquids Reference Collection (ILRC). These measurements are assembled into a preliminary database. From this selection, we discuss the significance and forensic application of the temperature data grid and the composition explicit data channel of the ADC. PMID:26401423

Fouling in Membrane Distillation, Osmotic Distillation and Osmotic Membrane Distillation

Directory of Open Access Journals (Sweden)

Mourad Laqbaqbi

2017-03-01

Full Text Available Various membrane separation processes are being used for seawater desalination and treatment of wastewaters in order to deal with the worldwide water shortage problem. Different types of membranes of distinct morphologies, structures and physico-chemical characteristics are employed. Among the considered membrane technologies, membrane distillation (MD, osmotic distillation (OD and osmotic membrane distillation (OMD use porous and hydrophobic membranes for production of distilled water and/or concentration of wastewaters for recovery and recycling of valuable compounds. However, the efficiency of these technologies is hampered by fouling phenomena. This refers to the accumulation of organic/inorganic deposits including biological matter on the membrane surface and/or in the membrane pores. Fouling in MD, OD and OMD differs from that observed in electric and pressure-driven membrane processes such electrodialysis (ED, membrane capacitive deionization (MCD, reverse osmosis (RO, nanofiltration (NF, ultrafiltration (UF, microfiltration (MF, etc. Other than pore blockage, fouling in MD, OD and OMD increases the risk of membrane pores wetting and reduces therefore the quantity and quality of the produced water or the concentration efficiency of the process. This review deals with the observed fouling phenomena in MD, OD and OMD. It highlights different detected fouling types (organic fouling, inorganic fouling and biofouling, fouling characterization techniques as well as various methods of fouling reduction including pretreatment, membrane modification, membrane cleaning and antiscalants application.

Wound-healing and antimicrobial properties of dichloromethane fraction of Dialium guineense (Wild) fruit coat.

Science.gov (United States)

Okeke, Nnadi Charles; Udeani, Theophilus Kc; Onyebuchi, Ugwu Linus

2016-01-01

This research established the scientific bases for the folkloric use of the neglected Dialium guineense fruit coat in wound and microbial infection management in Nigeria. The phytochemical analysis of the crude extract, fractions and sub-fractions was performed by standard methods. Agar well diffusion protocol was adopted for the antimicrobial assay while the wound healing properties was determined by full thickness skin excision wound model. Phytochemical analysis showed high relative proportion of alkaloids (6.05 ± 0.98 %), saponins (3.91 ± 0.02 %) and tannins (1.86 ± 0.05 %). The only active fraction (DF) and sub-fraction (DF-5) were effective against Gram-positive (inhibition zone diameters, IZDs, 8-10 mm and 11-15 mm) and Gram-negative (IZDs, 15-19 mm and 16-21 mm) bacteria and fungi (6-8 mm) compared with 20-24 mm and 18-19 mm of the standard (ciprofloxacin) respectively. Fifty mg/kg of the DF-5 showed nearly equal percentage wound healing post-surgery days to Cicatrin®. The 50 mg/kg dose of DF and DF-5 showed more than 50 % wound healing at 10(th) day post-surgery, 50 mg/kg crude extract showed 54 % on day 14 while distilled water showed 56 % wound healing on day 17 with no sign of infection in all animal groups. All the treatments were significantly (P<0.01) different from control (distilled water) in wound healing by the 10(th) and 17(th) post-surgery days. The studies revealed that the fruit coat, which hitherto was treated as wastes could be explored for antimicrobial and wound healing properties against the backdrop of continually emerging antibiotic resistant strains of microorganisms.

27 CFR 24.183 - Use of distillates containing aldehydes.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Use of distillates... distillates containing aldehydes. Distillates containing aldehydes may be received on wine premises for use in the fermentation of wine and then returned to the distilled spirits plant from which distillates were...

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1946-08-29

A continuous method of distilling shale to produce valuable hydrocarbon oils is described which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors from the zone, mixing fresh cold shale with the hydrocarbon vapors to quench the same, whereby the fresh shale is preheated, recovering hydrocarbon vapors and product vapors from the mixture and withdrawing preheated shale from the mixture and charging it to a shale distillation zone.

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Heyl, G E

1917-02-06

The yield of oil obtained by distilling shale is increased by first soaking the shale with about 10 percent of its volume of a liquid hydrocarbon for a period of 24 hours or longer. Distillation is carried on up to a temperature of about 220/sup 0/C., and a further 10 percent of hydrocarbon is then added and the distillation continued up to a temperature of about 400/sup 0/C.

Vacuum distillation residue upgrading by an indigenous Bacillus cereus.

Science.gov (United States)

Tabatabaee, Mitra Sadat; Mazaheri Assadi, Mahnaz

2013-07-16

Biological processing of heavy fractions of crude oils offers less severe process conditions and higher selectivity for refining. Biochemical Processes are expected to be low demand energy processes and certainly ecofriendly. A strain of biosurfactant producing bacterium was isolated from an oil contaminated soil at Tehran refinery distillation unit. Based on selected phenotypic and genotypic characteristic including morphology, biochemical proprety, and 16 SrRNA sequencing identified as a novel strain of Bacillus cereus (JQ178332). This bacterium endures a wide range of pH, salinity and temperature. This specific strain utilizes both paraffin and anthracene as samples of aliphatic and polycyclic aromatic hydrocarbons. The ability of this bacterium to acquire all its energy and chemical requirements from Vacuum Distillation Residue (VR), as a net sample of problematic hydrocarbons in refineries, was studied. SARA test ASTM D4124-01 revealed 65.5% decrease in asphaltenic, 22.1% in aliphatics and 30.3% in Aromatics content of the VR in MSM medium. Further results with 0.9% saline showed 55% decrease in asphaltene content and 2.1% Aromatics respectively. Remarkable abilities of this microorganism propose its application in an ecofriendly technology to upgrade heavy crude oils.

Development of a pilot molecular distillation unit; Desenvolvimento de unidade de destilacao molecular nacional e aplicacao na avaliacao de petroleos extrapesados

Energy Technology Data Exchange (ETDEWEB)

Rocha, Erica Roberta Lovo da; Maciel, Maria Regina Wolf; Maciel Filho, Rubens; Batistella, Cesar Benedito [Universidade Estadual de Campinas (UNICAMP), SP (Brazil); Medina, Lilian Carmem [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2008-07-01

Due to the importance and the need in studies with heavy and extra heavy petroleums and their residues, it was designed and built up by the oil research group of LOPCA/LDPS/FEQ/UNICAMP, in partnership with the Laboratory of Valuation Processes of CENPES / PETROBRAS, a pilot plant of falling film molecular distiller (national prototype), where some specific operational facilities were introduced. This project resulted in a suitable system for distillation of products of high molecular weight and thermally sensitive, without degradation of them. This work aims the achievement of distillate fractions of atmospheric residue 400 deg C+, using the new molecular distillation equipment. The experiments were carried out according to factorial design to assess the significant process variables in the molecular distillation prototype. The results showed that the evaporator temperature has high influence on the process and the feed flow rate has minimum influence, as it is desired. Additionally, the equipment showed easy handing operation, high operational stability and results varying around 1%. (author)

40 CFR 721.9635 - Terpene residue distillates.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Terpene residue distillates. 721.9635... Substances § 721.9635 Terpene residue distillates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as terpene residue distillates (PMN P-96-897...

MIKROEMULSIFIKASI FRAKSI TIDAK TERSABUNKAN DISTILAT ASAM LEMAK MINYAK SAWIT [Microemulsification of Unsaponifiable Fractions of Palm Fatty Acid Distillate

Directory of Open Access Journals (Sweden)

Teti Estiasih

2015-12-01

Full Text Available Palm fatty acid distillate (PFAD is a by-product of palm oil refining that contains valuable bioactive compounds such as phytosterols, tocopherol, tocotrienols, and squalene which acummulates in unsaponifiable fraction (USF. In emulsion form, USF will be convenient and easy to use as food supplements or fortificants. Microemulsion is a type of emulsion that has stable droplet sizes of less than 10 m. Hence, the best emulsifier for USF microemulsion is important to be determined. The USF microemulsion was prepared by homogenizing the sample mixtures at 12.000 rpm for 20 min at USF concentration of 10% (w/v with lecithin and tween 80 as the emulsifiers at concentratiosn of 0.5, 1.0, and 1.5% (w/v. The microemulsions were analyzed for their viscosity, stability, and particle size distributions, as well as microstructures. The results showed that characteristics of microemulsion were affected by emulsifier types and concentrations. Tween 80 produced better microemulsion than lecithin as indicated by more stable emulsions, smaller droplet sizes, and narrower ranges of droplet size distributions. Increasing lectihin concentrations resulted in a narrower droplet size distribution but the average droplet size was not always smaller. Conversely, increasing tween 80 concentrations increased the average droplet sizes and ranges of particle size distributions. The most suitable emulsifier for USF microemulsion was tween 80 at concentration of 0.5%. This microemulsion contained bioactive compounds derived from USF, namely vitamin E (mainly tocotrienols, phytosterols, and squalene.

Sodium distiller II

International Nuclear Information System (INIS)

Goncalves, A.C.; Castro, P.M. e; Torres, A.R.; Correa, S.M.

1990-01-01

A sodium distiller allows the evaluation of the sodium purity, contained in plants and circuits of Fast Reactors. The sodium distillers of the IEN Reactor's Department was developed initially as a prototype, for the testing of the distillation process and in a second step, as a equipment dedicated to attendance the operation of these circuits. This last one was build in stainless steel, with external heat, rotating crucible of nickel for four samples, purge system for pipe cleaning and a sight glass that permits the observation of the distillation during all the operation. The major advantage of this equipment is the short time to do a distillation operation, which permits its routine utilization. As a consequence of the development of the distillers and its auxiliary systems an important amount of new information was gathered concerning components and systems behaviour under high temperature, vacuum and sodium. (author)

Distilling tar; distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Brash, P; Young, W

1866-09-17

The tarry residue, which separates on treating crude shale oil with sulfuric acid, is redistilled, in the manner described in Specification No. 1278, A.D. 1866, together with shale. Previous to the distillation, the acid is neutralized with lime, or may be separated by blowing steam into the tar and adding salt. The purified tar thus obtained is absorbed by ashes, or is mixed with lime or other alkaline matter, or the shale may be mixed with lime and distilled with the tar, which is allowed to flow over and through the shale during the process. The tar obtained in the purification of natural paraffin may be similarly utilized.

A comparison of the toluene distillation and vacuum/heat methods for extracting soil water for stable isotopic analysis

Science.gov (United States)

Ingraham, Neil L.; Shadel, Craig

1992-12-01

Hanford Loam, from Richland, Washington, was used as a test soil to determine the precision, accuracy and nature of two methods to extract soil water for stable isotopic analysis: azeotropic distillation using toluene, and simple heating under vacuum. The soil was oven dried, rehydrated with water of known stable isotopic compositions, and the introduced water was then extracted. Compared with the introduced water, initial aliquots of evolved water taken during a toluene extraction were as much as 30 ‰ more depleted in D and 2.7 ‰ more depleted in 18O, whereas final aliquots were as much as 40 ‰ more enriched in D and 14.3 ‰ more enriched in 18O. Initial aliquots collected during the vacuum/heat extraction were as much as 64 ‰ more depleted in D and 8.4 ‰ more depleted in 18O than was the introduced water, whereas the final aliquots were as much as 139 ‰ more enriched in D, and 20.8 ‰ more enriched in 18O. Neither method appears quantitative; however, the difference in stable isotopic composition between the first and last aliquots of water extracted by the toluene method is less than that from the vacuum/heat method. This is attributed to the smaller fractionation factors involved with the higher average temperatures of distillation of the toluene. The average stable isotopic compositions of the extracted water varied from that of the introduced water by up to 1.4 ‰ in δD and 4.2 ‰ in δ18O with the toluene method, and by 11.0 ‰ in δD and 1.8 ‰ in δ18O for the vacuum/heat method. The lack of accuracy of the extraction methods is thought to be due to isotopic fractionation associated with water being weakly bound (not released below 110°C) in the soil. The isotopic effect of this heat-labile water is larger at low water contents (3.6 and 5.2% water by weight) as the water bound in the soil is a commensurately larger fraction of the total. With larger soilwater contents the small volume of water bound with an associated fractionation is

Effects of distillation system and yeast strain on the aroma profile of Albariño (Vitis vinifera L.) grape pomace spirits.

Science.gov (United States)

Arrieta-Garay, Y; Blanco, P; López-Vázquez, C; Rodríguez-Bencomo, J J; Pérez-Correa, J R; López, F; Orriols, I

2014-10-29

Orujo is a traditional alcoholic beverage produced in Galicia (northwest Spain) from distillation of grape pomace, a byproduct of the winemaking industry. In this study, the effect of the distillation system (copper charentais alembic versus packed column) and the yeast strain (native yeast L1 versus commercial yeast L2) on the chemical and sensory characteristics of orujo obtained from Albariño (Vitis vinifera L.) grape pomace has been analyzed. Principal component analysis, with two components explaining 74% of the variance, is able to clearly differentiate the distillates according to distillation system and yeast strain. Principal component 1, mainly defined by C6-C12 esters, isoamyl octanoate, and methanol, differentiates L1 from L2 distillates. In turn, principal component 2, mainly defined by linear alcohols, linalool, and 1-hexenol, differentiates alembic from packed column distillates. In addition, an aroma descriptive test reveals that the distillate obtained with a packed column from a pomace fermented with L1 presented the highest positive general impression, which is associated with the highest fruity and smallest solvent aroma scores. Moreover, chemical analysis shows that use of a packed column increases average ethanol recovery by 12%, increases the concentration of C6-C12 esters by 25%, and reduces the concentration of higher alcohols by 21%. In turn, L2 yeast obtained lower scores in the alembic distillates aroma profile. In addition, with L1, 9% higher ethanol yields were achieved, and L2 distillates contained 34%-40% more methanol than L1 distillates.

Tritium Isotope Separation Using Adsorption-Distillation Column

International Nuclear Information System (INIS)

Fukada, Satoshi

2005-01-01

In order to miniaturize the height of a distillation tower for the detritiation of waste water from fusion reactors, two experiments were conducted: (1) liquid frontal chromatography of tritium water eluting through an adsorption column and (2) water distillation using a column packed with adsorbent particles. The height of the distillation tower depends on the height equivalent to a theoretical plate, HETP, and the equilibrium isotope separation factor, α H-T equi . The adsorption action improved not only HETP but also α H-T equi . Since the adsorption-distillation method proposed here can shorten the tower height with keeping advantages of the distillation, it may bring an excellent way for miniaturizing the distillation tower to detritiate a large amount of waste water from fusion reactors

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Justice, P M

1917-09-19

Light paraffin oils and other oils for motors are obtained from shale, and benzene, toluene, and solvent naphtha are obtained from coal by a process in which the coal or shale is preferably powered to pass through a mesh of 64 to the inch and is heated with a mixture of finely ground carbonate or the like which under the action of heat gives off carbonic acid, and with small iron scrap or its equivalent which is adapted to increase the volume of hydrocarbons evolved. The temperature of the retort is maintained between 175 and 800/sup 0/C., and after all the vapors are given off at the higher temperature a fine jet of water may be injected into the retort and the temperature increased. The produced oil is condensed and purified by fractional distillation, and the gas formed is stored after passing it through a tower packed with coke saturated with a non-volatile oil with recovery of an oil of light specific gravity which is condensed in the tower. The residuum from the still in which the produced oil is fractionated may be treated with carbonate and iron, as in the first stage of the process, and the distillate therefrom passed to a second retort containing manganese dioxide and iron scrap preferably in the proportion of one part or two. The mixture, e.g., one containing shale or oil with six to thirteen percent of oxygen, to which is added three to eight per cent of carbonate, and from one and a half to four per cent of scrap iron, is conveyed by belts and an overhead skip to a hopper of a retort in a furnace heated by burners supplied with producer gas. The retort is fitted with a detachable lid and the vapors formed are led by a pipe to a vertical water-cooled condenser with a drain-cock which leads the condensed oils to a tank, from which a pipe leads to a packed tower for removing light oils and from which the gas passes to a holder.

Phytotoxic activity of crude aqueous extracts and fractions of young leaves of Sapindus saponaria L. (Sapindaceae

Directory of Open Access Journals (Sweden)

Patrícia Umeda Grisi

2013-03-01

Full Text Available The aim of this study was to evaluate the phytotoxic potential of aqueous extract of young leaves of Sapindus saponaria L. (soapberry on the diaspore germination and seedling growth Lactuca sativa L. (lettuce and Allium cepa L. (onion, as well as to determine, by bioassay-guided fractioning, whether the fractionated extracts of those leaves are phytotoxic to Triticum aestivum L. (wheat coleoptiles. The aqueous extract was prepared using 100 g of dried plant material dissolved in 1000 ml of distilled water, resulting in a concentration of 10.0%. Distilled water was added in order to obtain dilutions of 7.5%, 5.0%, and 2.5%. The extraction was carried out with young leaves (in powder form and organic solvents of various polarities. We fractioned the ethyl acetate extract using column chromatography. The phytotoxic potential of the aqueous extract of young leaves S. saponaria varied according to the receiving species and the concentration-dependent inhibitory effect. The ethyl acetate extract, specifically fraction 6 (57-70, had the greatest inhibitory effect on the elongation of wheat coleoptiles, indicating that the compounds responsible for the phytotoxic effect reside within this fraction.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

1938-07-05

A process and apparatus for the destructive distillation at low temperature of mineral or organic material particularly oil shale, is given in which the process comprises distilling the material in a horizontal gaseous stream, subjecting the hot residues to the action of a gaseous stream containing a predetermined amount of oxygen so as to burn, at least partly, the carbon-containing substances, and the process uses the gases from this combustion for the indirect heating of the gases serving for the distillation.

Process modeling and control applied to real-time monitoring of distillation processes by near-infrared spectroscopy.

Science.gov (United States)

de Oliveira, Rodrigo R; Pedroza, Ricardo H P; Sousa, A O; Lima, Kássio M G; de Juan, Anna

2017-09-08

A distillation device that acquires continuous and synchronized measurements of temperature, percentage of distilled fraction and NIR spectra has been designed for real-time monitoring of distillation processes. As a process model, synthetic commercial gasoline batches produced in Brazil, which contain mixtures of pure gasoline blended with ethanol have been analyzed. The information provided by this device, i.e., distillation curves and NIR spectra, has served as initial information for the proposal of new strategies of process modeling and multivariate statistical process control (MSPC). Process modeling based on PCA batch analysis provided global distillation trajectories, whereas multiset MCR-ALS analysis is proposed to obtain a component-wise characterization of the distillation evolution and distilled fractions. Distillation curves, NIR spectra or compressed NIR information under the form of PCA scores and MCR-ALS concentration profiles were tested as the seed information to build MSPC models. New on-line PCA-based MSPC approaches, some inspired on local rank exploratory methods for process analysis, are proposed and work as follows: a) MSPC based on individual process observation models, where multiple local PCA models are built considering the sole information in each observation point; b) Fixed Size Moving Window - MSPC, in which local PCA models are built considering a moving window of the current and few past observation points; and c) Evolving MSPC, where local PCA models are built with an increasing window of observations covering all points since the beginning of the process until the current observation. Performance of different approaches has been assessed in terms of sensitivity to fault detection and number of false alarms. The outcome of this work will be of general use to define strategies for on-line process monitoring and control and, in a more specific way, to improve quality control of petroleum derived fuels and other substances submitted

Biocatalytic desulfurization of petroleum and middle distillates

International Nuclear Information System (INIS)

Monticello, D.J.

1993-01-01

Biocatalytic Desulfurization (BDS) represents an alternative approach to the reduction of sulfur in fossil fuels. The objective is to use bacteria to selectively remove sulfur from petroleum and middle distillate fractions, without the concomitant release of carbon. Recently, bacteria have been developed which have the ability to desulfurize dibenzothiophene (DBT) and other organosulfur molecules. These bacteria are being developed for use in a biocatalyst-based desulfurization process. Analysis of preliminary conceptual engineering designs has shown that this process has the potential to complement conventional technology as a method to temper the sulfur levels in crude oil, or remove the recalcitrant sulfur in middle distillates to achieve the deep desulfurization mandated by State and Federal regulations. This paper describes the results of initial feasibility studies, sensitivity analyses and conceptual design work. Feasibility studies with various crude oils and middle distillates achieved unoptimized desulfurization levels of 40-80%. Sensitivity analyses indicate that total desulfurization costs of about $3.00 per barrel for crude oil and less than $2.00 per barrel for diesel are possible. Key criteria for commercial success of the process include the cost and half-life of the biocatalyst, residence time in the reactor, oil/water ratios required to extract the sulfur and the disposition of the separated sulfur products. 9 refs., 3 figs

Distillation time effect on lavender essential oil yield and composition.

Science.gov (United States)

Zheljazkov, Valtcho D; Cantrell, Charles L; Astatkie, Tess; Jeliazkova, Ekaterina

2013-01-01

Lavender (Lavandula angustifolia Mill.) is one of the most widely grown essential oil crops in the world. Commercial extraction of lavender oil is done using steam distillation. The objective of this study was to evaluate the effect of the length of the distillation time (DT) on lavender essential oil yield and composition when extracted from dried flowers. Therefore, the following distillation times (DT) were tested in this experiment: 1.5 min, 3 min, 3.75 min, 7.5 min, 15 min, 30 min, 60 min, 90 min, 120 min, 150 min, 180 min, and 240 min. The essential oil yield (range 0.5-6.8%) reached a maximum at 60 min DT. The concentrations of cineole (range 6.4-35%) and fenchol (range 1.7-2.9%) were highest at the 1.5 min DT and decreased with increasing length of the DT. The concentration of camphor (range 6.6-9.2%) reached a maximum at 7.5-15 min DT, while the concentration of linalool acetate (range 15-38%) reached a maximum at 30 min DT. Results suggest that lavender essential oil yield may not increase after 60 min DT. The change in essential oil yield, and the concentrations of cineole, fenchol and linalool acetate as DT changes were modeled very well by the asymptotic nonlinear regression model. DT may be used to modify the chemical profile of lavender oil and to obtain oils with differential chemical profiles from the same lavender flowers. DT must be taken into consideration when citing or comparing reports on lavender essential oil yield and composition.

27 CFR 30.1 - Gauging of distilled spirits.

Science.gov (United States)

2010-04-01

... correcting hydrometer indications at temperatures between 0 and 100 degrees Fahrenheit to true proof. If distilled spirits contain dissolved solids, temperature correction of the hydrometer reading by the use of...

Distilling oil shale

Energy Technology Data Exchange (ETDEWEB)

Crozier, R H

1923-04-18

In the fractional distillation of oils from oil shale and similar materials the charge is passed continuously through a vertical retort heated externally by hot combustion gases in flues and internally by the passage of these gases through flues passing through the retort so that zones of increasing temperature are maintained. A vapor trap is provided in each zone having an exit pipe leading through a dust trap to a condenser. The bottoms of the conical vapor traps are provided with annular passages perforated to permit of steam being sprayed into the charge to form screens which prevent the vapors in different zones from mingling, and steam may also be introduced through perforations in an annular steam box. Dampers are provided to control the passage of the heating gases through the flues independently.

Hydrogen solubility measurements of analyzed tall oil fractions and a solubility model

International Nuclear Information System (INIS)

Uusi-Kyyny, Petri; Pakkanen, Minna; Linnekoski, Juha; Alopaeus, Ville

2017-01-01

Highlights: • Hydrogen solubility was measured in four tall oil fractions between 373 and 597 K. • Continuous flow synthetic isothermal and isobaric method was used. • A Henry’s law model was developed for the distilled tall oil fractions. • The complex composition of the samples was analyzed and is presented. - Abstract: Knowledge of hydrogen solubility in tall oil fractions is important for designing hydrotreatment processes of these complex nonedible biobased materials. Unfortunately measurements of hydrogen solubility into these fractions are missing in the literature. This work reports hydrogen solubility measured in four tall oil fractions between 373 and 597 K and at pressures from 5 to 10 MPa. Three of the fractions were distilled tall oil fractions their resin acids contents are respectively 2, 20 and 23 in mass-%. Additionally one fraction was a crude tall oil (CTO) sample containing sterols as the main neutral fraction. Measurements were performed using a continuous flow synthetic isothermal and isobaric method based on the visual observation of the bubble point. Composition of the flow was changed step-wise for the bubble point composition determination. We assume that the tall oil fractions did not react during measurements, based on the composition analysis performed before and after the measurements. Additionally the densities of the fractions were measured at atmospheric pressure from 293.15 to 323.15 K. A Henry’s law model was developed for the distilled tall oil fractions describing the solubility with an absolute average deviation of 2.1%. Inputs of the solubility model are temperature, total pressure and the density of the oil at 323.15 K. The solubility of hydrogen in the CTO sample can be described with the developed model with an absolute average deviation of 3.4%. The solubility of hydrogen increases both with increasing pressure and/or increasing temperature. The more dense fractions of the tall oil exhibit lower hydrogen

Quick assessment of binary distillation efficiency using a heat engine perspective

International Nuclear Information System (INIS)

Blahušiak, M.; Kiss, A.A.; Kersten, S.R.A.; Schuur, B.

2016-01-01

With emphasis on close boiling, (near-)ideal VLE mixtures, this paper links the efficiency of distillation to the binary feed composition and thermal properties of the compounds. The proposed approach, treating the process as a heat engine, allows to directly quantify distillation performance (in terms of energy intensity & efficiency) based on the components boiling points and feed composition. In addition, this approach reviews and formulates simple, approximate and essentially non-iterative calculation procedures to quickly estimate the energy efficiency of distillation. These estimations may be applied to identify opportunities to save significant amounts of energy. The results show that the reboiler duty for low relative volatility is relatively independent of the heat of vaporization and feed composition, while being reciprocally proportional to the Carnot efficiency of the distillation column. The internal efficiency for distillation of mixtures with low relative volatility has a maximum of about 70% for a symmetrical feed (equimolar ratio) and decreases to zero for unsymmetrical feed compositions approaching infinite dilution. With increasing relative volatility, the maximum efficiency is preserved, but the locus shifts towards lower light component fractions. At very high relative volatility, the internal efficiency increases with decreasing concentration of light component, as typical for evaporators. - Highlights: • A heat engine perspective was applied to estimate binary distillation efficiency. • The method was derived from first principles. • Validation on industrial cases showed the strength of the method.

Organic palladium and palladium-magnesium chemical modifiers in direct determination of lead in fractions from distillation of crude oil by electrothermal atomic absorption analysis

Science.gov (United States)

Kowalewska, Zofia; Bulska, Ewa; Hulanicki, Adam

1999-05-01

Platinum reforming catalysts are easily poisoned by increased levels of lead, therefore a sensitive atomic absorption spectrometric procedure for lead determination in fractions from crude oil distillation was developed. Lead was present in organic form in the samples analysed therefore the behaviour of various lead compounds (Pb-alkylarylsulphonate, Pb-4-cyclohexanobutyrate, tetraethyllead, Pb in fuel oil) was studied. The best procedure for the determination of lead in different petroleum products, including those containing asphaltenes includes a pretreatment with iodine and methyltrioctylammonium chloride, followed by the use of an organic Pd-Mg modifier. Under these conditions an effective matrix removal is possible at a pyrolysis temperature up to approximately 1100°C and the behaviour of lead present in different forms is unified. The characteristic mass is 11-12 pg Pb, corresponding to a detection limit of 0.25 ng g -1 for 20 μl sample solution. This can be lowered by multiple injection.

Reoxidation of uranium in electrolytically reduced simulated oxide fuel during residual salt distillation

International Nuclear Information System (INIS)

Eun-Young Choi; Jin-Mok Hur; Min Ku Jeon; University of Science and Technology, Yuseong-gu, Daejeon

2017-01-01

We report that residual salt removal by high-temperature distillation causes partial reoxidation of uranium metal to uranium oxide in electrolytically reduced simulated oxide fuel. Specifically, the content of uranium metal in the above product decreases with increasing distillation temperatures, which can be attributed to reoxidation by Li 2 O contained in residual salt (LiCl). Additionally, we estimate the fractions of Li 2 O reacted with uranium metal under these conditions, showing that they decrease with decreasing temperature, and calculate some thermodynamic parameters of the above reoxidation. (author)

Distillation of oil-bearing minerals

Energy Technology Data Exchange (ETDEWEB)

1952-05-21

In the process of distilling oil-bearing minerals such as oil shale which disintegrates during distillation, wherein the subdivided minerals are subjected to a distillation temperature in the form of a highly turbulent dense mass fluidized by an upwardly flowing gasiform medium in a distillation zone and the heat required by the distillation is supplied by burning solid distillation residue with a combustion-supporting gas in the form of a fluidized mass of solids in a separate combustion zone at a temperature substantially higher than the distillation temperature and returning solid combustion residue substantially at the higher temperature to the distillation zone. The steps of starting up the process which consists of maintaining in the distillation and combustion zones dense turbulent fluidized beds of non-disintegrating solids, circulating the non-disintegrating solids between said beds, heating the circulating solids by an auxiliary heat supply until the bed in the distillation zone has reached at least the distillation temperature, thereafter charging fresh oil-bearing minerals to the bed in the distillation zone, continuing the circulation, withdrawing solids which have passed through the combustion zone at a rate adequate to maintain a solids balance, supplying the combustion-supporting gas to the combustion zone to cause the combustion of the residue, and discontinuing the auxilary heating when sufficient heat for the distillation is being generated in the combustion zone.

In vitro assessment of relief to oxidative stress by different fractions of Boerhavia procumbens.

Science.gov (United States)

Abbasi, Muhammad Athar; Rubab, Kaniz; Rehman, Azizur; Riaz, Tauheeda; Shahzadi, Tayyaba; Khalid, Muniba; Ajaib, Muhammad

2012-04-01

Methanolic extract of Boerhavia procumbens Bank ex Roxb. was partitioned with n-hexane, chloroform, ethyl acetate and n-butanol sequentially after dissolving in distilled water. Phytochemical screening showed presence of phenolics, flavonoides and cardiac glycosides in large amount in chloroform, ethyl acetate and n-butanol soluble fraction. The antioxidant activity of all these fractions and the remaining aqueous fraction was evaluated by four methods such as: 1,1-diphenyl-2-picrylhydrazyl (DPPH) free radical scavenging activity, ferric reducing antioxidant power (FRAP) assay, total antioxidant activity and ferric thiocyanate assay. Total phenolics were also determined. Some fractions showed noteworthy antioxidant activity. The results of the antioxidant activity revealed that the ethyl acetate soluble fraction showed the highest value of percent inhibition of DPPH (82.54 ± 0.62) at the concentration of 125 μ g/ml. The IC(50) of this fraction was 37.11± 0.23 μg/ml, compared with butylated hydroxytoluene (BHT), which have IC(50) of 12.1 ± 0.92 μ/mL. It also showed the highest FRAP value (251.08 ± 1.46 μg of trolox equivalents) as well as the highest value of lipid peroxidation inhibition (57.21 ± 52%), the highest total antioxidant activity (0.549 ± 0.08) and also the highest total phenolic contents (77.1 ± 0.6) as compared to the studied fractions. Phytochemical screening showed high percentage of phenolics, flavonoides and cardiac glycosides in this fraction.

Vacuum Distillation Residue Upgrading by an Indigenous Bacillus Cereus

Directory of Open Access Journals (Sweden)

Mitra Sadat Tabatabaee

2013-07-01

Full Text Available Background:Biological processing of heavy fractions of crude oils offers less severe process conditions and higher selectivity for refining. Biochemical Processes are expected to be low demand energy processes and certainly ecofriendly.Results:A strain of biosurfactant producing bacterium was isolated from an oil contaminated soil at Tehran refinery distillation unit. Based on selected phenotypic and genotypic characteristic including morphology, biochemical proprety, and 16 SrRNA sequencing identified as a novel strain of Bacillus cereus (JQ178332. This bacterium endures a wide range of pH, salinity and temperature. This specific strain utilizes both paraffin and anthracene as samples of aliphatic and polycyclic aromatic hydrocarbons. The ability of this bacterium to acquire all its energy and chemical requirements from Vacuum Distillation Residue (VR, as a net sample of problematic hydrocarbons in refineries, was studied. SARA test ASTM D4124-01 revealed 65.5% decrease in asphaltenic, 22.1% in aliphatics and 30.3% in Aromatics content of the VR in MSM medium. Further results with 0.9% saline showed 55% decrease in asphaltene content and 2.1% Aromatics respectively.Conclusion:Remarkable abilities of this microorganism propose its application in an ecofriendly technology to upgrade heavy crude oils.

Monitoring PAI-1 and VEGF Levels in 6 Human Squamous Cell Carcinoma Xenografts During Fractionated Irradiation

International Nuclear Information System (INIS)

Bayer, Christine; Kielow, Achim; Schilling, Daniela; Maftei, Constantin-Alin; Zips, Daniel; Yaromina, Ala; Baumann, Michael; Molls, Michael; Multhoff, Gabriele

2012-01-01

Purpose: Previous studies have shown that the plasminogen activator inhibitor type-1 (PAI-1) and vascular endothelial growth factor (VEGF) are regulated by hypoxia and irradiation and are involved in neoangiogenesis. The aim of this study was to determine in vivo whether changes in PAI-1 and VEGF during fractionated irradiation could predict for radiation resistance. Methods and Materials: Six xenografted tumor lines from human squamous cell carcinomas (HSCC) of the head and neck were irradiated with 0, 3, 5, 10, and 15 daily fractions of 2 Gy. The PAI-1 and VEGF antigen levels in tumor lysates were determined by enzyme-linked immunosorbent assay kits. The amounts of PAI-1 and VEGF were compared with the dose to cure 50% of tumors (TCD 50 ). Colocalization of PAI-1, pimonidazole (hypoxia), CD31 (endothelium), and Hoechst 33342 (perfusion) was examined by immunofluorescence. Results: Human PAI-1 and VEGF (hVEGF) expression levels were induced by fractionated irradiation in UT-SCC-15, UT-SCC-14, and UT-SCC-5 tumors, and mouse VEGF (msVEGF) was induced only in UT-SCC-5 tumors. High hVEGF levels were significantly associated with radiation sensitivity after 5 fractions (P=.021), and high msVEGF levels were significantly associated with radiation resistance after 10 fractions (P=.007). PAI-1 staining was observed in the extracellular matrix, the cytoplasm of fibroblast-like stroma cells, and individual tumor cells at all doses of irradiation. Colocalization studies showed PAI-1 staining close to microvessels. Conclusions: These results indicate that the concentration of tumor-specific and host-specific VEGF during fractionated irradiation could provide considerably divergent information for the outcome of radiation therapy.

Toxicity and toxicokinetics of binary combinations of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

Science.gov (United States)

Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

2013-04-01

Petroleum hydrocarbons (PHCs) act via narcosis and are expected to have additive toxicity. However, previous work has demonstrated less-than-additive toxicity with PHC distillates and earthworms. A study was initiated to investigate this through toxicity and toxicokinetic studies with the earthworm Eisenia andrei. Three petroleum distillate fractions, F2 (>C10-C16), F3a (>C16-C23), and F3b (>C23-C34), were used in two binary combinations, F2F3a and F3aF3b. In the toxicity study, clean soil was spiked with equitoxic combinations of the two distillates ranging from 0.5 to 2.5 toxic units. In the toxicokinetic study, a binary combination consisting of one concentration of each distillate was used. On a soil concentration basis, the toxicity of the binary combinations of distillates was less than additive. Accumulation of the individual distillates, however, was generally reduced when a second distillate was present, resulting in lower body burden. This is thought to be due to the presence of a nonaqueous-phase liquid at the soil concentrations used. On a tissue concentration basis, toxicity was closer to additive. The results demonstrate that tissue concentrations are the preferred metric for toxicity for earthworms. They also demonstrate that the Canada-wide soil standards based on individual distillates are likely protective. Copyright © 2013 SETAC.

Study of the repartition of phthalate esters during distillation of wine for spirit production.

Science.gov (United States)

Montevecchi, Giuseppe; Masino, Francesca; Di Pascale, Nicolas; Vasile Simone, Giuseppe; Antonelli, Andrea

2017-12-15

Due to health concerns and legal matters, an investigation to limit phthalates esters (PEAs) in spirits is necessary. A lab still was used to perform pilot distillations according to the official method for brandy production in order to explore the repartition into the distilled fractions of each PAE. The process was divided in two steps: a première chauffe and a bonne chauffe. The former step included the cut into heads, heart and tails, while the latter into heads, brandy, secondes, and tails. The behaviour of each PAE during distillation was affected by its own chemical nature. Dibutyl phthalate (DBP) was entirely carried over into the distillate, while bis(2-ethylhexyl) phthalate (DEHP) only partially, and diisononyl phthalate (DINP) accumulated in the stillage. During the bonne chauffe, DBP and DEHP accumulated in the secondes more than in the brandy. A rectification step of the secondes was demonstrated to considerably reduce PAEs concentration. Copyright © 2017. Published by Elsevier Ltd.

Use of refractometry to determine fraction content to 175/sup 0/ in raw coking-chemical benzene

Energy Technology Data Exchange (ETDEWEB)

Lasak, K

1980-01-01

Fraction content to 175/sup 0/C, one of the main quality indicators for benzene, is usually determined via distillation, which requires considerable time and effort. In order to determine this fraction use of refractive index is suggested, using an Abbe or Meopta type refractometer. The refractive index for this fraction is considerably lower than in distillation residue, which contains naphthalene, indene, and higher-boiling compounds. This paper describes technique, calibration curves, and results characterizing accuracy of test, comprising + or - 0.5%.

Cascade Distiller System Performance Testing Interim Results

Science.gov (United States)

Callahan, Michael R.; Pensinger, Stuart; Sargusingh, Miriam J.

2014-01-01

The Cascade Distillation System (CDS) is a rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. Based upon the results of the 2009 distillation comparison test (DCT) and recommendations of the expert panel, the Advanced Exploration Systems (AES) Water Recovery Project (WRP) project advanced the technology by increasing reliability of the system through redesign of bearing assemblies and improved rotor dynamics. In addition, the project improved the CDS power efficiency by optimizing the thermoelectric heat pump (TeHP) and heat exchanger design. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell d International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades as compared to previous system performance. The system was challenged with Solution 1 from the NASA Exploration Life Support (ELS) distillation comparison testing performed in 2009. Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. A secondary objective of this testing is to evaluate the performance of the CDS as compared to the state of the art Distillation Assembly (DA) used in the ISS Urine Processor Assembly (UPA). This was done by challenging the system with ISS analog waste streams. This paper details the results of the AES WRP CDS performance testing.

Influência do dióxido de enxofre e cultivares de videira na formação de alguns compostos voláteis e na qualidade sensorial do destilado de vinho Influence of sulfur dioxide and grape varieties at the formation of some volatile compounds and at the sensory quality of the wine distillate

Directory of Open Access Journals (Sweden)

Marco Antonio SALTON

2000-12-01

distillates was accomplished by the sensory group of EMBRAPA Uva e Vinho. The results showed that the sulfur dioxide helped the formation of ethanal in the grape varieties studied. It was also observed an increase in the fusel oil fraction due to the sulfur dioxide, except for the distillate of the Isabel grape variety. It was showed also that the Isabel’s distillated had a higher fraction of methanol and lower of 1-propanol, possibly due to the vinification process. The Isabel distillate together with the Couderc 13 distillate, showed a lower fraction of 2-methyl-1-propanol and a lower fraction of 3-methyl-1-butanol and the fusel oil fraction as compared with the other distillates. The distillate of Trebbiano presented a higher fraction of 2-methyl-1-propanol and together with the Herbemont distillate a higher fraction of 1-propanol, 2-methyl-1-butanol and fusel oil. The sensory evaluation showed that the SO2 had an influence in the aroma, taste and in the general quality of the Herbemont and Trebbiano distillates. The Herbemont distillate was characterized by presenting a lower aroma, taste and general quality. It presented, also, negativelly the highest score for undesirable aroma and taste.

Distilled water nasal provocation in hyperreactive patients.

Science.gov (United States)

Baudoin, T; Anzic, S A; Kalogjera, L

1999-01-01

Nonisotonic aerosol may act as a provocation agent in the upper and lower airways of hyperreactive individuals. The purpose of the study was to compare the results of nasal challenge with distilled water in patients with allergic rhinitis to those with noninfective nonallergic rhinitis (NINAR), with respect to the potential clinical use of the obtained data. A group of 68 ambulatory patients with allergic rhinitis or NINAR (39 perennial allergic, 6 seasonal, 23 NINAR) were challenged with 10 mL of distilled water aerosol after the baseline active anterior rhinomanometry. Patients with nasal polyposis at endoscopy, significant unilateral septal deviation, positive bacteriologic swab, recent nasal surgery, and uncertain anamnestic data about the medication taken 6 weeks before the provocation were excluded from the study. After 10 minutes of nasal provocation, rhinomanometry was repeated to assess the response. In 15 patients of the perennial allergic group, the same measurements were performed after a 2-week oral antihistamine and topical steroid therapy. Nasal resistance was significantly increased on the more patent side of the nose after nasal provocation with distilled water aerosol in allergic patients in comparison to the nasal resistance before provocation. In the patients with NINAR, the provocation resulted in a significant rise on the more patent side, but the total nasal airway resistance (NAR) levels were also significantly increased. The systemic antihistamine and topical steroid 2-week therapy in patients with perennial allergic rhinitis significantly reduced the response to nasal distilled water provocation. Nasal provocation with distilled water aerosol is a cheap, simple, and acceptable method that provides useful clinical data on the level of nonspecific nasal hyperreactivity and the therapy success.

Secondary Aroma Compounds in Fresh Grape Marc Distillates as a Result of Variety and Corresponding Production Technology

Directory of Open Access Journals (Sweden)

Borislav Miličević

2011-01-01

Full Text Available In order to investigate the composition of secondary aroma compounds of fresh grape marc distillates as a result of variety and production technology, 30 samples (6 varieties×5 samples were analysed. White grape marc samples from Malvazija istarska, Chardonnay and Muscat Blanc were obtained as by-products in standard white wine production, while red grape marc samples from Teran and Cabernet Sauvignon were obtained after standard red wine production procedures. Marc from red grape variety Muškat ruža porečki was obtained during the production of rosé wines. All fermented marc samples were distilled using a traditional copper alembic. The obtained distillates were subjected to GC/MS and GC/FID analyses. Malvazija istarska distillates exhibited exceptionally high methanol content. Distillates from white grape varieties were found to be characterized by higher C6 alcohol and 1-propanol concentrations, while red grape distillates contained higher amounts of the majority of alcohols, acids, and esters. In Muškat ruža distillates intermediate concentrations of many important aroma compounds were found. It was concluded that differences in the production technology parameters, depending on the variety, resulted in differences in secondary aroma profiles, most evident between distillates from white and red varieties. These findings were confirmed applying stepwise linear discriminant analysis (SLDA, which resulted in 100 % correct classification of distillates according to the variety and corresponding production technology.

THE CLUSTER AND FIELD GALAXY ACTIVE GALACTIC NUCLEUS FRACTION AT z = 1-1.5: EVIDENCE FOR A REVERSAL OF THE LOCAL ANTICORRELATION BETWEEN ENVIRONMENT AND AGN FRACTION

International Nuclear Information System (INIS)

Martini, Paul; Miller, E. D.; Bautz, M.; Brodwin, M.; Stanford, S. A.; Gonzalez, Anthony H.; Hickox, R. C.; Stern, D.; Eisenhardt, P. R.; Galametz, A.; Norman, D.; Dey, A.; Jannuzi, B. T.; Murray, S.; Jones, C.; Brown, M. J. I.

2013-01-01

The fraction of cluster galaxies that host luminous active galactic nuclei (AGNs) is an important probe of AGN fueling processes, the cold interstellar medium at the centers of galaxies, and how tightly black holes and galaxies co-evolve. We present a new measurement of the AGN fraction in a sample of 13 clusters of galaxies (M ≥ 10 14 M ☉ ) at 1 A = 3.0 +2.4 -1.4 % for AGNs with a rest-frame, hard X-ray luminosity greater than L X, H ≥ 10 44 erg s –1 . This fraction is measured relative to all cluster galaxies more luminous than M * 3.6 (z) + 1, where M * 3.6 (z) is the absolute magnitude of the break in the galaxy luminosity function at the cluster redshift in the IRAC 3.6 μm bandpass. The cluster AGN fraction is 30 times greater than the 3σ upper limit on the value for AGNs of similar luminosity at z ∼ 0.25, as well as more than an order of magnitude greater than the AGN fraction at z ∼ 0.75. AGNs with L X, H ≥ 10 43 erg s –1 exhibit similarly pronounced evolution with redshift. In contrast to the local universe, where the luminous AGN fraction is higher in the field than in clusters, the X-ray and MIR-selected AGN fractions in the field and clusters are consistent at 1 < z < 1.5. This is evidence that the cluster AGN population has evolved more rapidly than the field population from z ∼ 1.5 to the present. This environment-dependent AGN evolution mimics the more rapid evolution of star-forming galaxies in clusters relative to the field.

THE CLUSTER AND FIELD GALAXY ACTIVE GALACTIC NUCLEUS FRACTION AT z = 1-1.5: EVIDENCE FOR A REVERSAL OF THE LOCAL ANTICORRELATION BETWEEN ENVIRONMENT AND AGN FRACTION

Energy Technology Data Exchange (ETDEWEB)

Martini, Paul [Department of Astronomy and Center for Cosmology and Astroparticle Physics, Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States); Miller, E. D.; Bautz, M. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Brodwin, M. [Department of Physics and Astronomy, University of Missouri, 5110 Rockhill Road, Kansas City, MO 64110 (United States); Stanford, S. A. [Department of Physics, University of California, One Shields Avenue, Davis, CA 95616 (United States); Gonzalez, Anthony H. [Department of Astronomy, University of Florida, Gainesville, FL 32611 (United States); Hickox, R. C. [Department of Physics and Astronomy, Dartmouth College, 6127 Wilder Laboratory, Hanover, NH 03755 (United States); Stern, D.; Eisenhardt, P. R. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Galametz, A. [INAF-Osservatorio di Roma, Via Frascati 33, I-00040 Monteporzio (Italy); Norman, D.; Dey, A. [NOAO, 950 North Cherry Avenue, Tucson, AZ 85719 (United States); Jannuzi, B. T. [Department of Astronomy and Steward Observatory, University of Arizona, 933 North Cherry Avenue, Tucson, AZ 85721 (United States); Murray, S.; Jones, C. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Brown, M. J. I., E-mail: martini@astronomy.ohio-state.edu [School of Physics, Monash University, Clayton, Victoria 3800 (Australia)

2013-05-01

The fraction of cluster galaxies that host luminous active galactic nuclei (AGNs) is an important probe of AGN fueling processes, the cold interstellar medium at the centers of galaxies, and how tightly black holes and galaxies co-evolve. We present a new measurement of the AGN fraction in a sample of 13 clusters of galaxies (M {>=} 10{sup 14} M{sub Sun }) at 1 < z < 1.5 selected from the Spitzer/IRAC Shallow Cluster Survey, as well as the field fraction in the immediate vicinity of these clusters, and combine these data with measurements from the literature to quantify the relative evolution of cluster and field AGN from the present to z {approx} 3. We estimate that the cluster AGN fraction at 1 < z < 1.5 is f{sub A} = 3.0{sup +2.4}{sub -1.4}% for AGNs with a rest-frame, hard X-ray luminosity greater than L{sub X,{sub H}} {>=} 10{sup 44} erg s{sup -1}. This fraction is measured relative to all cluster galaxies more luminous than M{sup *}{sub 3.6}(z) + 1, where M{sup *}{sub 3.6}(z) is the absolute magnitude of the break in the galaxy luminosity function at the cluster redshift in the IRAC 3.6 {mu}m bandpass. The cluster AGN fraction is 30 times greater than the 3{sigma} upper limit on the value for AGNs of similar luminosity at z {approx} 0.25, as well as more than an order of magnitude greater than the AGN fraction at z {approx} 0.75. AGNs with L{sub X,{sub H}} {>=} 10{sup 43} erg s{sup -1} exhibit similarly pronounced evolution with redshift. In contrast to the local universe, where the luminous AGN fraction is higher in the field than in clusters, the X-ray and MIR-selected AGN fractions in the field and clusters are consistent at 1 < z < 1.5. This is evidence that the cluster AGN population has evolved more rapidly than the field population from z {approx} 1.5 to the present. This environment-dependent AGN evolution mimics the more rapid evolution of star-forming galaxies in clusters relative to the field.

Early changes produced in mouse skin by the application of three middle distillates.

Science.gov (United States)

Grasso, P; Sharratt, M; Ingram, A J

1988-01-01

It has been reported by the American Petroleum Institute (API) that dermal applications of certain middle distillates of mineral oils can result in high incidences of skin tumours in mice. This was unexpected as the polycyclic aromatic hydrocarbon (PAH) levels in these were below detection limits. To examine the possible role of tissue injury in the induction of tumours, the skin reactions produced by thrice weekly applications of three middle distillates similar to those tested by the API were examined grossly and histopathologically at intervals up to 6 weeks. Various reference materials and oils were used as controls. Preliminary histological examination showed that severe skin damage was present from week 1 onwards in mice treated with the three middle distillates, two of them producing epidermal loss and ulceration. Marked epidermal hyperplasia was produced by all three middle distillates. These findings support the view that regenerative epidermal hyperplasia due to repeated severe skin damage may have exerted a powerful promotional effect in the production of the skin tumours by middle distillates in the API study.

Convenient large-scale synthesis of D-glucaro-1,4:6,3-dilactone.

Science.gov (United States)

Gehret, Troy C; Frobese, A Stephen; Zerbe, James S; Chenault, H Keith

2009-11-06

Calcium D-glucarate was converted into D-glucaro-1,4:6,3-dilactone on 32-g, 1-kg, and 22-kg scale, using azeotropic distillation with methyl isobutyl ketone to drive the dehydration. The crystalline product was > or = 99.5% pure by GC and NMR, and overall yield was as high as 72%.

Distillation apparatus for solid materials

Energy Technology Data Exchange (ETDEWEB)

Lurmann, F

1860-06-26

The distillation room is continuously charged by the charging mechanism with the material to be distilled. The distillation products pass into the chamber, where they are drawn out through the tube for purifying. The distillation residue is finally pushed out by the fresh material from the room and falls in the common room, from which it is removed through the air-tight door. In the canals enclosing the room heating gas circulates, which carries to the room the heat necessary for the distillation.

Simulation and design of distillation units for treatment of sulfite pulping condensates to recover methanol and furfural. Part II. Applicability of multiple-effect distillation using live steam

Energy Technology Data Exchange (ETDEWEB)

Aly, G.; Zacchi, G.

1979-06-01

A distillation unit has been designed for a capacity of 73 t/h of condensate and for at least 90% recovery of the contaminating organics. This unit consists of three columns: a primary stripper to remove volatile organics and two upgrading columns to purify the methanol and furfural byproducts. Three different energy-saving alternatives for satisfying the energy requirements have been studied: utilisation of secondary steam from the evaporation plant, and application of the principle of multi-effect distillation in one-stripper and in two-stripper configurations. Investment cost needed in all alternatives amounts to 5.5 to 6.0 MCr (millions of Swedish Crowns) while operating cost varies between 0.8 to 3.1 MCr. The first design alternative has a payoff period of 2.3 years while the two multi-effect distillation alternatives have a payoff period of about 3 years.

Analysis and Environmental Fate of Air Force Distillate and High Density Fuels

Science.gov (United States)

1981-10-01

728.1 128 0.8 Toluenc 751.3 92 0.6 XTHDCPD 1049.6 136 66.8 NTHDCPD 1079.2 136 1.5HNN 1509.6 186 20.1 JP-1O XTHDCPD 1050.3 136 96.8 ITHDCPD 1079.6 136 1,5...deionized water and the salts listed below. Blanks of both waters were routinely extracted and analyzed for possible 4.nterferences. MNN PXTX XTHDCPD ...through 13; complete data summaries for the distillate fuels may be found in Appendix C. All com- ponents of the high density fuels except XTHDCPD of

Design of Batch Distillation Columns Using Short-Cut Method at Constant Reflux

Directory of Open Access Journals (Sweden)

Asteria Narvaez-Garcia

2013-01-01

Full Text Available A short-cut method for batch distillation columns working at constant reflux was applied to solve a problem of four components that needed to be separated and purified to a mole fraction of 0.97 or better. Distillation columns with 10, 20, 30, 40, and 50 theoretical stages were used; reflux ratio was varied between 2 and 20. Three quality indexes were used and compared: Luyben’s capacity factor, total annual cost, and annual profit. The best combinations of theoretical stages and reflux ratio were obtained for each method. It was found that the best combinations always required reflux ratios close to the minimum. Overall, annual profit was the best quality index, while the best combination was a distillation column with 30 stages, and reflux ratio’s of 2.0 for separation of benzene (i, 5.0 for the separation of toluene (ii, and 20 for the separation of ethylbenzene (iii and purification of o-xylene (iv.

Hypoxic fraction and binding of misonidazole in EMT6/Ed multicellular tumor spheroids

International Nuclear Information System (INIS)

Franko, A.J.

1985-01-01

Misonidazole has been shown to bind selectively to hypoxic cells in tissue culture and to cells which are presumed to be chronically hypoxic in EMT6 spheroids and tumors. Thus it has considerable potential as a marker of hypoxic cells in vivo. To further evaluate this potential EMT6/Ed spheroids were used to quantitate misonidazole binding under conditions which resulted in hypoxic fractions between 0 and 1. The patterns of binding of 14 C-labeled misonidazole determined by autoradiography were consistent with the regions of radiobiological hypoxia as predicted by oxygen diffusion theory. The overall uptake of 3 H-labeled misonidazole by spheroids correlated well with the hypoxic fraction, although binding to aerobic cells and necrotic tissue contributed appreciably to the total label in the spheroids. It is concluded that misonidazole is an excellent marker of hypoxia in EMT6/Ed spheroids at the microscopic level, and the total amount bound per spheroid provides a potentially useful measure of the hypoxic fraction

Barley fibre and wet distillers' solubles in the diet of growing cattle

Directory of Open Access Journals (Sweden)

T. ROOT

2008-12-01

Full Text Available Twenty-eight bulls were used in a 3 × 2 factorial design to study the effects of two by-products from the integrated starch-ethanol process, barley fibre and distillers' solubles, as supplements for grass silage. The animals were divided into five blocks and slaughtered when the average live weight (LW of each block reached 500 kg. The three energy supplements were barley (B, a mixture (1:1 on a dry matter (DM basis of barley and barley fibre (BF, and barley fibre (F, fed without (DS- or with (DS+ wet distillers' solubles (200 g kg-1 concentrate on DM basis. Concentrates were given at the rate of 95 g DM kg-1 LW0.6. Including barley fibre in the diet did not affect feed intake, but distillers' solubles tended to increase both silage and total DM intakes as well as amino acids absorbed in the intestine and energy intake. The protein balance in the rumen increased with the inclusion of barley fibre (P

77 FR 25382 - Proposed Amendment to the Standards of Identity for Distilled Spirits

Science.gov (United States)

2012-04-30

... set forth in Sec. 5.22(f) as follows: Class 6; rum. ``Rum'' is an alcoholic distillate from the..., produced at less than 190[deg] proof in such manner that the distillate possesses the taste, aroma and... mixtures solely of such distillates. The above standard does not currently provide for any subcategories or...

Isobaric vapor-liquid equilibria for the extractive distillation of 2-propanol + water mixtures using 1-ethyl-3-methylimidazolium dicyanamide ionic liquid

International Nuclear Information System (INIS)

Orchillés, A. Vicent; Miguel, Pablo J.; González-Alfaro, Vicenta; Llopis, Francisco J.; Vercher, Ernesto; Martínez-Andreu, Antoni

2017-01-01

Highlights: • VLE of binary and ternary systems of 2-propanol, water and [emim][DCA] at 100 kPa. • The e-NRTL model fits the VLE data of 2-propanol + water + [emim][DCA] system. • [emim][DCA] breaks the 2-propanol + water azeotrope at an IL mole fraction >0.085. - Abstract: Isobaric vapor–liquid equilibria for the binary systems 2-propanol + water, 2-propanol + 1-ethyl-3-methylimidazolium dicyanamide ([emim][DCA]), and water + [emim][DCA] as well as the vapor–liquid equilibria for the 2-propanol + water + [emim][DCA] ternary system have been obtained at 100 kPa using a recirculating still. The electrolyte nonrandom two-liquid (e-NRTL) model was used for fitting successfully the experimental data. The effect of [emim][DCA] on the 2-propanol + water system has been compared with that produced by other ionic liquids reported in the literature. From the results, [emim][DCA] appears as a good entrainer for the extractive distillation of this solvent mixture, causing the azeotrope to disappear at 100 kPa when the ionic liquid mole fraction is greater than 0.085.

21 CFR 184.1848 - Starter distillate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Starter distillate. 184.1848 Section 184.1848 Food... Specific Substances Affirmed as GRAS § 184.1848 Starter distillate. (a) Starter distillate (butter starter distillate) is a steam distillate of the culture of any or all of the following species of bacteria grown on...

Commissioning and operation of distillation column at Madras Atomic Power Station (Paper No. 1.10)

International Nuclear Information System (INIS)

Neelakrishnan, G.; Subramanian, N.

1992-01-01

In Madras Atomic Power Station (MAPS), an upgrading plant based on vacuum distillation was constructed to upgrade the downgraded heavy water collected in vapor recovery dryers. There are two distillation columns and each having a capacity of 77.5 tonne per annum of reactor grade heavy water with average feed concentration of 30% IP. The performance of the distillation columns has been very good. The column I and column II have achieved an operating factor of 92% and 90% respectively. The commissioning activities, and subsequent improvements carried out in the distillation columns are described. (author)

Solar distillation between a simple and double-glazing

Directory of Open Access Journals (Sweden)

Abderrahmane KHECHEKHOUCHE

2017-12-01

Full Text Available The south-east region of Algeria suffers from a great socio-economic problem that affects a large population. Faced with the unavailability of drinking water, solar distillation; which appears to be a suitable and inexpensive solution; was adopted by local researchers. Improving the productivity of a solar greenhouse distiller is the subject of several researches in the world. As it is well known, distiller with simple glazing is wildly studied but unfortunately has feeble efficiency. Double glazing is a method that increases the efficiency of a flat solar collector. The idea is to use the same technique on a single-slope solar distiller (50 x 50 cm. Two glass plates separated by 1 cm between them air is trapped. Experience shows that this technique has a negative effect on the productivity of the distiller with a rate of 88.63%; it means 9 times. So double glazing is not recommended in the single slope solar distiller.

Low temperature distillation

Energy Technology Data Exchange (ETDEWEB)

1937-07-21

To distil mineral or organic material, the material is heated by means of a hot gas entering into contact with and traversing the material in a horizontal direction. The vertical retort is charged with material from the hopper and hot gases from the furnace after traversing the boiler enter the preheating zone, pass through the slots and charge therein and are educted through connection by the blower. The charge passes downwardly to the distillation zone wherein hot gases from the heater are passed via pipe and slots through the chambers and to the pipe controlled by the dampers. These gases are recycled by the fan through the heater and chamber, that portion of the gases corresponding to the amount of vapours evolved from the distillation being evacuated via the pipe to the condensing plant not shown. Steam and/or a limited quantity of water may be admitted to the distillation zone.

Regenerative adsorption distillation system

KAUST Repository

Ng, Kim Choon; Thu, Kyaw; Amy, Gary; Chunggaze, Mohammed; Al-Ghasham, Tawfiq

2013-01-01

There is provided a regenerative adsorption distillation system comprising a train of distillation effects in fluid communication with each other. The train of distillation effects comprises at least one intermediate effect between the first and last distillation effects of the train, each effect comprising a vessel and a condensing tube for flow of a fluid therein. The system further comprises a pair of adsorption-desorption beds in vapour communication with the last effect and at least one intermediate effect, wherein the beds contain an adsorbent that adsorbs vapour from the last effect and transmits desorbed vapour into at least one of the intermediate effect.

Regenerative adsorption distillation system

KAUST Repository

Ng, Kim Choon

2013-12-26

There is provided a regenerative adsorption distillation system comprising a train of distillation effects in fluid communication with each other. The train of distillation effects comprises at least one intermediate effect between the first and last distillation effects of the train, each effect comprising a vessel and a condensing tube for flow of a fluid therein. The system further comprises a pair of adsorption-desorption beds in vapour communication with the last effect and at least one intermediate effect, wherein the beds contain an adsorbent that adsorbs vapour from the last effect and transmits desorbed vapour into at least one of the intermediate effect.

Distillation of bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Seguin, M

1875-02-16

The retort with its accessories constitutes a distillation apparatus for shale composed of a cylindrical, vertical, fixed, tubular, and of ring form metal retort. Also it is comprised of a special hearth of large dimensions in the form of a circular pocket receiving from the retort as heating agent the distilled shale and emitting by radiation the heat that makes the distillation apparatus for the shale act.

Energy optimization and comparative study of pre- and post-fractionator extractive dividing wall column for the CO2–ethane azeotropic process

International Nuclear Information System (INIS)

Tavan, Yadollah; Riazi, Seiied Hadi; Nozohouri, Mostafa

2014-01-01

Graphical abstract: - Highlights: • Two arrangements is proposed for extractive DWC based on pre- and post- fractionator. • Operating parameters are optimized to minimize energy demand. • The pre-fractionator design showed the best performance in comparison to others. - Abstract: Two possible extractive dividing-wall column (DWC) arrangements are explored to find the potential benefits derived from thermally coupled distillations in separation of a mixture including the CO 2 –ethane azeotrope with a low boiling point. It is shown that the process including pre-fractionator in the DWC design in its optimized state leads to 51.6% reduction in total duties in comparison with the conventional process. Furthermore, a comparison between conventional extractive distillation columns and the new DWC process is made in terms of cost estimation, CO 2 removal efficiency and CO 2 emission reduction. Remarkable, the results clearly show that DWC process is interesting/feasible and the novel proposed DWC alternative reduces the steam requirements by 41% and the equipment costs by 31%

Transient simulation of a solar heating system for a small-scale ethanol-water distillation plant: Thermal, environmental and economic performance

International Nuclear Information System (INIS)

Vargas-Bautista, Juan Pablo; García-Cuéllar, Alejandro Javier; Pérez-García, Santiago L.; Rivera-Solorio, Carlos I.

2017-01-01

Highlights: • Thermal simulation of a small solar ethanol distillation plant is performed. • The optimum collector area is obtained for two different thermal collectors types. • Higher solar fraction was found for parabolic trough collectors. • Economic analysis is performed for different scenarios to evaluate feasibility. - Abstract: The thermal, environmental and economic performance of a small-scale ethanol distillation system, where solar energy is used as primary energy source, was studied. Two different concentrations of ethanol at the feed stream (5 wt.% and 10 wt.%) were analysed to obtain a distillate product of 95 wt.% ethanol (hydrous ethanol). Evacuated tube solar collectors (ETC) and parabolic trough collectors (PTC) were considered for the solar heating system. A case of study for a specific geographical place (Monterrey, México) was developed herein to evaluate the solar ethanol distillation system; the results can be extended to other locations, weather conditions and operational parameters. The thermal results from the simulation showed that through an adequate selection of the solar collector area and an appropriate sizing of the different equipment of the solar distillation system, PTC represents a better option where energy savings of 80% and 71% can be achieved for 5 wt.% and 10 wt.% ethanol at the feed stream, respectively. However, the economic feasibility of the solar distillation system is achieved using ETC for a price of hydrous ethanol of 1.75 USD/L and a feed stream of 10 wt.% ethanol, reaching an internal rate of return (IRR) of 18.8% and payback period of 5.2 years. As an important technical result, selected ETC presented advantages over PTC where an average distillate product of 3.6 and 3.4 ml at 95 wt.% ethanol can be obtained per unit of solar energy (kW h) captured per area (m"2) of solar collector using 5 wt.% and 10 wt.% ethanol at the feed stream, respectively (36% more than PTC). The reduction of greenhouse gases (GHG

Energy efficiency of acetone, butanol, and ethanol (ABE) recovery by heat-integrated distillation.

Science.gov (United States)

Grisales Diaz, Victor Hugo; Olivar Tost, Gerard

2018-03-01

Acetone, butanol, and ethanol (ABE) is an alternative biofuel. However, the energy requirement of ABE recovery by distillation is considered elevated (> 15.2 MJ fuel/Kg-ABE), due to the low concentration of ABE from fermentation broths (between 15 and 30 g/l). In this work, to reduce the energy requirements of ABE recovery, four processes of heat-integrated distillation were proposed. The energy requirements and economic evaluations were performed using the fermentation broths of several biocatalysts. Energy requirements of the processes with four distillation columns and three distillation columns were similar (between 7.7 and 11.7 MJ fuel/kg-ABE). Double-effect system (DED) with four columns was the most economical process (0.12-0.16 $/kg-ABE). ABE recovery from dilute solutions by DED achieved energy requirements between 6.1 and 8.7 MJ fuel/kg-ABE. Vapor compression distillation (VCD) reached the lowest energy consumptions (between 4.7 and 7.3 MJ fuel/kg-ABE). Energy requirements for ABE recovery DED and VCD were lower than that for integrated reactors. The energy requirements of ABE production were between 1.3- and 2.0-fold higher than that for alternative biofuels (ethanol or isobutanol). However, the energy efficiency of ABE production was equivalent than that for ethanol and isobutanol (between 0.71 and 0.76) because of hydrogen production in ABE fermentation.

Energy savings in distillation via identification of useful configurations

Science.gov (United States)

Shah, Vishesh Hemanshu

Recent market and environmental forces require the rapid development of better and cheaper separation process solutions. Especially for multicomponent mixtures, there are several feasible separation process solutions differing significantly in cost and energy consumption in spite of carrying out the same overall process. Therefore a systematic method to identify and design optimal multicomponent separation sequences is needed instead of relying on the inventive activity of a few experienced engineers. Even for a commonly perceived "mature" technology such as distillation, until recently there has been an absence of systematic methods to (i) elucidate all possible separation configurations and to (ii) identify energy efficient candidates. This research aims to address these needs. In this work, we focus on the continuous distillation of non-azeotropic mixtures into n distinct composition final product streams. We develop a computationally efficient and easy-to-use mathematical framework to generate all the basic distillation configurations that use exactly (n-1) distillation columns to carry out this n-component separation. We extend the framework to generate all the additional distillation configurations with thermal coupling. We observe that the search space of distillation configurations grows very rapidly as the number of product streams increases. For instance, for a mixture to be separated into 4 product streams, we can choose from 18 basic configurations and 134 additional configurations with thermal coupling; while for a mixture to be separated into 8 product streams, we can choose from 15,767,207 basic configurations and 29,006,926,681 additional configurations with thermal coupling. The next challenge for a process engineer is to be able to quickly prune the search space to a handful of attractive energy efficient candidates that can be studied in greater detail. To this effect, we develop a quick screening optimization tool that identifies configurations

Separation of H-D mixtures by cryogenic distillation

International Nuclear Information System (INIS)

Luo Yangming; Gu Mei; Wang Heyi; Liu Jun; Fu Zhonghua; Xia Xiulong; Liu Yunnu; Weng Kuiping; Xie Bo; Ren Xingbi

2007-01-01

In this paper, separation of hydrogen-deuterium mixtures were performed on a cryogenic distillation apparatus. The results show that the D/H ratio in the reboiler reduced to 1.27x10 -2 at 120h with a flow flux of 5mol/h of the gas mixture in D/H ratio of 1.4xl0 -4 . The enrichment effect increased apparently with D/H ratio of the feeding gas. However, the deuterium content in the top of distillation column increased with the deuterium content in the reboiler, and the de-deuterium efficiencies decreased. In the full reflux experiment, the de-deuterium efficiency increased with heating power of the reboiler, and the inside pressure in the distillation column increased, too. It was necessary that suitable heating power should be chosen in order to control operation pressure in the cryogenic distillation process. (authors)

Study of distillation and degradation of perfluoro polyether

International Nuclear Information System (INIS)

Lopergolo, Lilian Cristine

1997-01-01

Perfluoro-polyethers, PFPE, were first synthesised by Sianesi and collaborators giving rise to a new lubricant oils and greases classes with several applications. Perfluoro polyethers have excellent properties, for instance: high chemical stability and thermal stability, high density, high radiation resistance and excellent lubricating properties. FOMBLIN-Y oil is one of the perfluoro polyethers used as a lubricant in vacuum systems applied in the UF 6 enrichment installations. Due to its excellent properties and for its applications in the nuclear field, IPEN-CNEN/S P had the interest to dominate its production technology with the aim to substitute the commercial FOMBLIN-Y oil used in the national consumption. The FOMBLIN-Y oil synthesis method, adopted in IPEN-CNEN/S P, made by the photooxidation of the hexa fluoro propylene. In this work we study the fraction separation of the national available production with restricted an increased molecular weights which was obtained by fraction distillation in a vacuum according to the ASTM D-1160 norm. We also study the catalytic effect of metals on the thermal stability of perfluoro polyethers. The inertness of perfluoro polyethers at temperatures higher than 300 deg C is strongly affected by presence of some metals. Al and Ti alloys cause fluid degradation at 250 deg C. This degradation is very important because it has a yield increase of the perfluoro polyethers production. (author)

Aromatically enhanced pear distillates from blanquilla and conference varieties using a packed column.

Science.gov (United States)

Arrieta-Garay, Yanine; García-Llobodanin, Laura; Pérez-Correa, José Ricardo; López-Vázquez, Cristina; Orriols, Ignacio; López, Francisco

2013-05-22

Pear distillates are generally produced from the Bartlett variety because of its rich aroma. In this study, a chemical and sensorial comparative examination of pear distillates from the three main varieties grown in Spain (Bartlett, Blanquilla, and Conference) using two distillation systems (copper Charentais alembic and packed column) was undertaken. Volatile compounds were identified by gas chromatography to differentiate the spirits according to pear variety and distillation method. The Bartlett distillates from both distillation systems possessed higher ethyl ester and acetate and lower cis-3-hexen-1-ol and 1-hexanol concentrations. Despite these differences, a sensory analysis panel could distinguish only the Bartlett alembic distillate from the alembic distillates of the other varieties. In contrast, the panel rated the packed-column distillates equally. Therefore, less aromatic pear varieties can be used to produce distillates with aromatic characteristics similar to those of the Bartlett variety if a suitable distillation process is used.

Distilling shale and coal

Energy Technology Data Exchange (ETDEWEB)

Edwards, H; Young, G

1923-01-09

In a process of recovering oil from shale or coal the material is ground and may be subjected to a cleaning or concentrating process of the kind described in Specification 153,663 after which it is distilled in a furnace as described in Specification 13,625/09 the sections of the furnace forming different temperature zones, and the rate of the passage of the material is regulated so that distillation is complete with respect to the temperature of each zone, the whole distillation being accomplished in successive stages. The vapors are taken off at each zone and superheated steam may be passed into the furnace at suitable points and the distillation terminated at any stage of the process.

Fundamental Study on the Separation of Methane Isotopomer by Cryogenic Distillation

Energy Technology Data Exchange (ETDEWEB)

Song, K.M.; Lee, S.K.; Kim, K.S.; Kim, W.S. [Korea Electric Power Research Institute, Taejon (Korea)

2002-07-01

For the purpose of {sup 13}CH{sub 4} production from LNG, the state art of the application of C-13 and the marketing research were investigated. The theoretical number of stages and the number of distillation column required for the separation of {sup 13}CH{sub 4} from {sup 12}CH{sub 4}/{sup 13}CH{sub 4} mixture containing 1%-{sup 13}CH{sub 4} are calculated. Assuming the ideal liquid mixture of {sup 12}CH{sub 4} and {sup 13}CH{sub 4}, the theoretical number of stages are calculated the minimum theorical number of stages are calculated by Smoker equation and FUG method. Using the correlation between the minimum theoretical number of stages and the optimum theoretical number of stages, the number of distillation groups is obtained. From the simulation, we postulate that 6 groups of distillation tower having 600 stages per one column are needed for the production of 90%-{sup 13}CH{sub 4}. (author). 18 refs., 33 figs., 9 tabs.

27 CFR 5.47 - Standards of fill (distilled spirits bottled before January 1, 1980).

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Standards of fill (distilled spirits bottled before January 1, 1980). 5.47 Section 5.47 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF...

Herbal distillates: A new era of grape marc distillates with enriched antioxidant profile.

Science.gov (United States)

Andreou, Vasiliki; Strati, Irini F; Fotakis, Charalambos; Liouni, Maria; Zoumpoulakis, Panagiotis; Sinanoglou, Vassilia J

2018-07-01

Grape marc distillates are traditional alcoholic beverages, produced mostly in the Mediterranean countries. The present study proposes the enrichment of a Greek traditional grape marc distillate (tsikoudia) with selected herbs to enhance its natural antioxidants and functional properties. Total phenolic content, the antiradical and antioxidant activities, as well as the phenolic and sugar profiles using NMR and FT-IR spectroscopy were evaluated. The enrichment of distillates with Syzygium aromaticum L., Jasminum officinale L. and Eucalyptus globulus Labill. exhibited the highest total phenolic content as well as the highest antioxidant and antiradical activities, whereas the lowest values were observed with Hippophae rhamnoides L. and Lycium Barbarum Mill. The implementation of NMR and FT-IR spectroscopies attested to the presence of phenolic compounds and of specific carbohydrates in herbal distillates, postulating their migration from selected herbal species to tsikoudia and probably contributing to their organoleptic characteristics. The target of this approach leads to new added-value distillates with enhanced characteristics. Copyright © 2018 Elsevier Ltd. All rights reserved.

Antioxidant enzyme activity and malondialdehyde levels can be modulated by Piper betle, tocotrienol rich fraction and Chlorella vulgaris in aging C57BL/6 mice.

Science.gov (United States)

Aliahmat, Nor Syahida; Noor, Mohd Razman Mohd; Yusof, Wan Junizam Wan; Makpol, Suzana; Ngah, Wan Zurinah Wan; Yusof, Yasmin Anum Mohd

2012-12-01

The aim of this study was to determine the erythrocyte antioxidant enzyme activity and the superoxide dismutase, catalase, glutathione peroxidase, and plasma malondialdehyde levels in aging mice and to evaluate how these measures are modulated by potential antioxidants, including the tocotrienol-rich fraction, Piper betle, and Chlorella vulgaris. One hundred and twenty male C57BL/6 inbred mice were divided into three age groups: young (6 months old), middle-aged (12 months old), and old (18 months old). Each age group consisted of two control groups (distilled water and olive oil) and three treatment groups: Piper betle (50 mg/kg body weight), tocotrienol-rich fraction (30 mg/kg), and Chlorella vulgaris (50 mg/kg). The duration of treatment for all three age groups was two months. Blood was withdrawn from the orbital sinus to determine the antioxidant enzyme activity and the malondialdehyde level. Piper betle increased the activities of catalase, glutathione peroxidase, and superoxide dismutase in the young, middle, and old age groups, respectively, when compared to control. The tocotrienol-rich fraction decreased the superoxide dismutase activity in the middle and the old age groups but had no effect on catalase or glutathione peroxidase activity for all age groups. Chlorella vulgaris had no effect on superoxide dismutase activity for all age groups but increased glutathione peroxidase and decreased catalase activity in the middle and the young age groups, respectively. Chlorella vulgaris reduced lipid peroxidation (malondialdehyde levels) in all age groups, but no significant changes were observed with the tocotrienol-rich fraction and the Piper betle treatments. We found equivocal age-related changes in erythrocyte antioxidant enzyme activity when mice were treated with Piper betle, the tocotrienol-rich fraction, and Chlorella vulgaris. However, Piper betle treatment showed increased antioxidant enzymes activity during aging.

Antioxidant enzyme activity and malondialdehyde levels can be modulated by Piper betle, tocotrienol rich fraction and Chlorella vulgaris in aging C57BL/6 mice

Directory of Open Access Journals (Sweden)

Nor Syahida Aliahmat

2012-12-01

Full Text Available OBJECTIVE: The aim of this study was to determine the erythrocyte antioxidant enzyme activity and the superoxide dismutase, catalase, glutathione peroxidase, and plasma malondialdehyde levels in aging mice and to evaluate how these measures are modulated by potential antioxidants, including the tocotrienol-rich fraction, Piper betle, and Chlorella vulgaris. METHOD: One hundred and twenty male C57BL/6 inbred mice were divided into three age groups: young (6 months old, middle-aged (12 months old, and old (18 months old. Each age group consisted of two control groups (distilled water and olive oil and three treatment groups: Piper betle (50 mg/kg body weight, tocotrienol-rich fraction (30 mg/kg, and Chlorella vulgaris (50 mg/kg. The duration of treatment for all three age groups was two months. Blood was withdrawn from the orbital sinus to determine the antioxidant enzyme activity and the malondialdehyde level. RESULTS: Piper betle increased the activities of catalase, glutathione peroxidase, and superoxide dismutase in the young, middle, and old age groups, respectively, when compared to control. The tocotrienol-rich fraction decreased the superoxide dismutase activity in the middle and the old age groups but had no effect on catalase or glutathione peroxidase activity for all age groups. Chlorella vulgaris had no effect on superoxide dismutase activity for all age groups but increased glutathione peroxidase and decreased catalase activity in the middle and the young age groups, respectively. Chlorella vulgaris reduced lipid peroxidation (malondialdehyde levels in all age groups, but no significant changes were observed with the tocotrienol-rich fraction and the Piper betle treatments. CONCLUSION: We found equivocal age-related changes in erythrocyte antioxidant enzyme activity when mice were treated with Piper betle, the tocotrienol-rich fraction, and Chlorella vulgaris. However, Piper betle treatment showed increased antioxidant enzymes

27 CFR 26.230 - Containers of distilled spirits to bear closures.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Containers of distilled spirits to bear closures. 26.230 Section 26.230 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO... distilled spirits to bear closures. Containers of 1 gallon (3.785 liters) or less of distilled spirits, upon...

Application of the Advanced Distillation Curve Method to Fuels for Advanced Combustion Engine Gasolines

KAUST Repository

Burger, Jessica L.

2015-07-16

© This article not subject to U.S. Copyright. Published 2015 by the American Chemical Society. Incremental but fundamental changes are currently being made to fuel composition and combustion strategies to diversify energy feedstocks, decrease pollution, and increase engine efficiency. The increase in parameter space (by having many variables in play simultaneously) makes it difficult at best to propose strategic changes to engine and fuel design by use of conventional build-and-test methodology. To make changes in the most time- and cost-effective manner, it is imperative that new computational tools and surrogate fuels are developed. Currently, sets of fuels are being characterized by industry groups, such as the Coordinating Research Council (CRC) and other entities, so that researchers in different laboratories have access to fuels with consistent properties. In this work, six gasolines (FACE A, C, F, G, I, and J) are characterized by the advanced distillation curve (ADC) method to determine the composition and enthalpy of combustion in various distillate volume fractions. Tracking the composition and enthalpy of distillate fractions provides valuable information for determining structure property relationships, and moreover, it provides the basis for the development of equations of state that can describe the thermodynamic properties of these complex mixtures and lead to development of surrogate fuels composed of major hydrocarbon classes found in target fuels.

Production of Methyl Laurate from Coconut Cream through Fractionation of Methyl Ester

Directory of Open Access Journals (Sweden)

Johnner P. Sitompul

2015-10-01

Full Text Available This paper concerns the production of methyl laurate from coconut cream through fractionation of methyl esters. Coconut oil was produced by wet processing of coconut cream. The esters were prepared by reacting coconut oil and methanol using homogeneous catalyst KOH in a batch reactor, followed by fractionation of fatty acid methyl esters (FAME at various reduced pressures applying differential batch vacuum distillation. Experimental data were compared with simulation of a batch distillation employing the simple Raoult’s model and modified Raoult’s model of phase equilibria. Activity coefficients (γi were determined by optimization to refine the models. The modified Rault’s model with activity coefficients gave better agreement with the experimental data, giving the value of γi between 0,56-0,73. For a given boiling temperature, lower operating pressure produced higher purity of C10 and C12 FAME for respective distillates.

Rhamnolipid produced by Pseudomonas aeruginosa USM-AR2 facilitates crude oil distillation.

Science.gov (United States)

Asshifa Md Noh, Nur; Al-Ashraf Abdullah, Amirul; Nasir Mohamad Ibrahim, Mohamad; Ramli Mohd Yahya, Ahmad

2012-01-01

A biosurfactant-producing and hydrocarbon-utilizing bacterium, Pseudomonas aeruginosa USM-AR2, was used to assist conventional distillation. Batch cultivation in a bioreactor gave a biomass of 9.4 g L(-1) and rhamnolipid concentration of 2.4 g L(-1) achieved after 72 h. Biosurfactant activity (rhamnolipid) was detected by the orcinol assay, emulsification index and drop collapse test. Pretreatment of crude oil TK-1 and AG-2 with a culture of P. aeruginosa USM-AR2 that contains rhamnolipid was proven to facilitate the distillation process by reducing the duration without reducing the quality of petroleum distillate. It showed a potential in reducing the duration of the distillation process, with at least 2- to 3-fold decreases in distillation time. This is supported by GC-MS analysis of the distillate where there was no difference between compounds detected in distillate obtained from treated or untreated crude oil. Calorimetric tests showed the calorie value of the distillate remained the same with or without treatment. These two factors confirmed that the quality of the distillate was not compromised and the incubation process by the microbial culture did not over-degrade the oil. The rhamnolipid produced by this culture was the main factor that enhanced the distillation performance, which is related to the emulsification of hydrocarbon chains in the crude oil. This biotreatment may play an important role to improve the existing conventional refinery and distillation process. Reducing the distillation times by pretreating the crude oil with a natural biosynthetic product translates to energy and cost savings in producing petroleum products.

Distillation Calculation for the Separation of {sup 13}CH{sub 4} from LNG

Energy Technology Data Exchange (ETDEWEB)

Song, K.M.; Son, S.H.; Kim, K.S.; Lee, S.K. [Korea Electric Power Research Institute, Taejon (Korea)

2002-07-01

For the purpose of {sup 13}CH{sub 4} production from LNG, the theoretical number of stages and the number of distillation column required for the separation of {sup 13}CH{sub 4} from {sup 12}CH{sub 4}/{sup 13}CH{sub 4} mixture of containing 1%-{sup 13}CH{sub 4} are calculated. Assuming the ideal liquid mixture of containing 1%-{sup 13}CH{sub 4} are calculated. Assuming the ideal liquid mixture of {sup 12}CH{sub 4} and {sup 13}CH{sub 4}, the theoretical number of stages are calculated by smoker equation and FUG method. Using the correlation between the minimum theoretical number of stages and the optimum theoretical number of stages, the number of distillation groups is calculated. From this calculation, we know that 6 groups of distillation tower with 600 stages per one column are needed for the production of 90%-{sup 13}CH{sub 4}. (author). 5 refs., 5 figs., 4 tabs.

Hybrid wind-power-distillation plant

Directory of Open Access Journals (Sweden)

Ninić Neven

2012-01-01

Full Text Available This paper reports and elaborates on the idea of a solar distiller and an offshore wind power plant operating together. The subject under discussion is a single-stage solar distillation plant with vaporization, using adiabatic expansion in the gravitational field inside a wind power plant supporting column. This scheme divides investment costs for electric power and distillate production. In the region of the Adriatic Sea, all electric power produced could be “converted” to hydrogen using less than 10% of the distillate produced.

27 CFR 28.301 - Loss of distilled spirits in transit.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Loss of distilled spirits in transit. 28.301 Section 28.301 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND....301 Loss of distilled spirits in transit. The tax on distilled spirits withdrawn without payment of...

Quantification of tumour initiating effect of jute batching oil and its distillates over mouse skin.

Science.gov (United States)

Agarwal, R; Kumar, S; Shukla, Y; Antony, M; Mehrotra, N K

1985-09-30

In order to identify the tumour initiating constituent(s) of a mineral oil, jute batching oil (JBO), used in the processing of jute fibres, it was fractionally distilled in various boiling range fractions. The latter were then subjected to in vivo assessment of their aryl hydrocarbon hydroxylase (AHH) inducing potential in mouse epidermis. Fractions with almost similar AHH inducing potential were regrouped and studied for their tumour initiating potential over mouse skin following two-stage initiation-promotion protocol and using 12-O-tetradecanoyl phorbol-13-acetate (TPA) as tumour promoter. It was noticed that: (1) JBO as initiator, provoked local development of benign skin tumours over mouse back; (2) fractions of JBO boiling below 335 degrees C and above 399 degrees C accounted for most of the tumour initiating potential of the oil; (3) the histological features of the tumours (i.e. benign papillomas and keratoacanthomas) initiated by these fractions were similar to those developed after being initiated with unfractionated or reconstituted JBO; (4) removal of these fractions from JBO may be attempted which could decontaminate the batch oil from most of its tumorigenic components and make it safer for industrial use.

Distillation with Sublogarithmic Overhead

Science.gov (United States)

Hastings, Matthew B.; Haah, Jeongwan

2018-02-01

It has been conjectured that, for any distillation protocol for magic states for the T gate, the number of noisy input magic states required per output magic state at output error rate ɛ is Ω [log (1 /ɛ )] . We show that this conjecture is false. We find a family of quantum error correcting codes of parameters ⟦ ∑ i =w +1 m (m i ),∑ i =0 w (m i ),∑ i =w +1 r +1 (r +1 i )⟧ for any integers m >2 r , r >w ≥0 , by puncturing quantum Reed-Muller codes. When m >ν r , our code admits a transversal logical gate at the ν th level of Clifford hierarchy. In a distillation protocol for magic states at the level ν =3 (T gate), the ratio of input to output magic states is O (logγ(1 /ɛ )) , where γ =log (n /k )/log (d )<0.678 for some m , r , w . The smallest code in our family for which γ <1 is on ≈258 qubits.

The Effect of Kaffir Lime Leaves Distillation Residue Oleoresin Concentration on Active Paper Packaging Characteristics

Science.gov (United States)

Kawiji; Utami, R.; Ulum, S.; Khasanah, L. U.; Manuhara, G. J.; Atmaka, W.

2018-03-01

Oleoresin of kaffir lime leaves distillation residue still contains some active compounds such as Citronellal, β-Citronellol, and Linalool which potential to incorporated on the active paper packaging. The purposes of this study were to determine the effect of kaffir lime leaves distillation residue oleoresin concentration on the physical characteristics, sensory characteristics, and antimicrobial activity of the active paper packaging incorporated with kaffir lime leaves distillation residue oleoresin and to determine the functional groups of active paper packaging. The concentration of kaffir lime leaves distillation residue oleoresin were varied at 0%, 2%, 4% and 6%. The result showed that the addition of kaffir lime leaves distillation residue oleoresin increased the thickness and moisture content of the paper and decreased the tensile strengths and folding endurances of active paper packaging. The microbial inhibition tends to increase along with the higher oleoresin concentration addition. Aromatic CH group were found at a wavelength of 897.90 cm-1 of on paper packaging with 2% oleoresin indicated as functional aromatic functional group allegedly obtained from the kaffir lime leaves oleoresin.

Mutagenicity and chemical characterization of two petroleum distillates.

Science.gov (United States)

Carver, J H; MacGregor, J A; King, R W

1984-08-01

To investigate if the Salmonella/microsome assay could reliably screen complex petroleum samples for their carcinogenic potential, two high boiling (700-1070 degrees F) petroleum distillates with known activity in a dermal carcinogenesis bioassay were fully characterized with respect to their hydrocarbon composition and polynuclear aromatic hydrocarbon (PNA) content and assayed for mutagenic activity. Mutagenicity assays were also carried out on the aromatic hydrocarbon aggregates separated from these oils by adsorption chromatography. The composition of the distillates differed substantially, and reflected the fact that they were derived from crude oils that were extremely divergent in hydrocarbon character. Both the distillate and aromatic samples consistently induced a very slight increase in revertant TA98 and TA100 colonies; however, an increase of 2-4-fold over background was observed when the S-9 concentration was increased 5-10 times that of the standard assay. The maximal response was less than that expected from the samples' known PNA content and observed potency in the dermal carcinogenesis bioassay. In the Salmonella/microsome assay, all samples inhibited the mutagenic activity of added benzo[a]pyrene. Discordance between the magnitude of the samples' mutagenic activity and their known PNA content may be related to direct or indirect inhibition of sample PNAs by other components of the complex petroleum fractions. Observed inhibitory effects support the use of elevated S-9 concentration in the in vitro assays assessing the carcinogenic potential of petroleum-derived materials.

Zone distillation: a new purification method

International Nuclear Information System (INIS)

Kravchenko, A.I.

2011-01-01

The features of zone distillation (with zone melting of refined material and with pulling of condensate) as a new purification method are shown. The method is based on similarity of equations of distillation and crystallization refining. The analogy between some distillation and condensation methods (particularly between zone distillation and zone recrystallization) is should up

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1948-08-03

A continuous method of distilling shale to produce valuable hydrocarbon oils is described, which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors containing shale fines from the zone, mixing sufficient fresh cold shale with the hydrocarbon vapors to quench the same and to cause condensation of the higher boiling constituents thereof, charging the mixture of vapors, condensate, and cold shale to a separation zone where the shale is maintained in a fluidized condition by the upward movement of the hydrocarbon vapors, withdrawing condensate from the separation zone and recycling a portion of the condensate to the top of the separation zone where it flows countercurrent to the vapors passing therethrough and causes shale fines to be removed from the vapors by the scrubbing action of the condensate, recovering hydrocarbon vapors and product vapors from the separation zone, withdrawing preheated shale from the separation zone and charging it to a shale distillation zone.

Destructive distillation: oils

Energy Technology Data Exchange (ETDEWEB)

West, J; Glover, S

1918-01-31

Canned and other coals are destructively distilled in continuously operated vertical retorts which at their upper portions are maintained at temperatures suitable for low temperature oil distillation such as about 700/sup 0/C, and at their lower portions the temperature is higher and such as to be suitable for the production of gas, e.g., about 1400/sup 0/C. Superheated steam is introduced into the lower portion of the retort, preferably by means of the arrangement described in Specification 120,458, and this is converted into blue water gas which assists the distillation in the center of the coal charge. The retorts are preferably such as are described in Specifications 2663/07 and 7757/14.

Research on the separation properties of empty-column gas chromatography (EC-GC) and conditions for simulated distillation (SIMDIS).

Science.gov (United States)

Boczkaj, Grzegorz; Kamiński, Marian

2013-10-01

Previous studies have revealed it is possible to separate a high-boiling mixture by gas chromatography in empty fused-silica capillary tubing rather than in columns coated with stationary phase. Chromatographic separation occurs solely on the basis of the different boiling points of the substances separated. The high similarity of such separations to those in classic distillation seems advantageous when gas chromatography is used for simulated distillation. This paper presents results from further research on the separation properties of empty fused silica tubing. The efficiency of this chromatographic system has been examined. The usefulness of such conditions has been studied for simulated distillation, i.e. to determine the boiling-point distribution of complex mixtures, mainly petroleum fractions and products, on the basis of their retention relative to reference substances. The results obtained by use of empty-column gas chromatography (EC-GC) and by use of classical simulated distillation columns have been compared for solutes of different polarity. Studies revealed boiling points determined by EC-GC were more accurate than those obtained by the standard method of simulated distillation.

Petroleum distillates suppress in vitro metabolic activation: higher [S-9] required in the Salmonella/microsome mutagenicity assay.

Science.gov (United States)

Carver, J H; Machado, M L; MacGregor, J A

1985-01-01

To determine if standard conditions used in the Salmonella/mammalian microsome mutagenicity assay could reliably screen complex petroleum samples, two high-boiling (700-1,070 degrees F) distillates and their separated aromatic fractions were tested. The initial mutagenic activities were inconsistent with the samples' known polyaromatic hydrocarbon (PAH) contents and observed potencies in a dermal carcinogenesis bioassay. A significant mutagenic response was observed only at S-9 concentrations 5 to 10 times higher than those used in the standard assay, supporting the use of elevated levels of S-9 in the Salmonella/microsome assay to assess the carcinogenic potential of petroleum-derived materials. All four samples masked the expected mutagenic activity of added PAHs (benzo[a]pyrene and perylene). Data suggested that petroleum distillates suppress the functional efficacy of the S-9; possible mechanisms are discussed.

Characterization of commercial ceramic adsorbents and its application on naphthenic acids removal of petroleum distillates

Directory of Open Access Journals (Sweden)

Juliana Pereira Silva

2007-06-01

Full Text Available The mixture of carboxylic acids present in petroleum oil and directly responsible for its acidity and corrosiveness in liquid phase during the refine process is denominated "naphthenic acids". These acids are also present in distilled fraction of petroleum, causing several problems in final products quality. A possible way to remove the carboxilic acids from petroleum distilled fractions is the adsorption in porous materials. However, the results obtained until now indicate that ion exchange resins would be the best adsorbents for this process, which would probably increase its cost. In this work, two commercial adsorbents (clay and activated alumina were characterized by a set of physical-chemistry techniques and evaluated concerning their capacity of removing naphthenic acids from a light petroleum fraction. It was verified the influence of a thermal treatment previous to the adsorption in its physical-chemistry characteristics and its properties. A high reduction of the TAN values was verified in the residual oils from both adsorbent, although there was a competition among all the compounds present in the light oil fraction for the adsorption sites, which can be probably related to the thermal pre-treatment. These results were related to corrosion yield experiments, and it was observed that the adsorbent pretreatment also affected the reduction in corrosion yields for both alumina and clay.

Distilling shale and the like

Energy Technology Data Exchange (ETDEWEB)

Gee, H T.P.

1922-02-23

In distilling shale or like bituminous fuels by internal heating with hot gas obtained by the gasifying of the shale residues with air or steam or a mixture of these, the amount and temperature of the gaseous distilling medium is regulated between the gasifying and the distilling chambers, by the introduction of cold gas or air.

Distillation with labelled transition systems

DEFF Research Database (Denmark)

Hamilton, Geoffrey William; Jones, Neil

2012-01-01

In this paper, we provide an improved basis for the " distillation" program transformation. It is known that superlinear speedups can be obtained using distillation, but cannot be obtained by other earlier automatic program transformation techniques such as deforestation, positive supercompilation...... and partial evaluation. We give distillation an improved semantic basis, and explain how superlinear speedups can occur....

Exergy analysis of a distillation tower for crude oil fractionation

International Nuclear Information System (INIS)

Rivero, R.

1990-01-01

In this paper the application of the exergy method to a crude oil atmospheric distillation tower is presented. The fundamentals and procedures are presented as well as the main parameters used to describe the thermodynamic performance of the system, such as Exergy Losses, Effectiveness and Improvement Potential. A parametric analysis of the influence on the effectiveness of the tower is then performed as a function of the number of trays, the amount of stripping steam, the use of reboilers and the operation pressure. The results obtained are discussed. As expected, the effectiveness of the tower increases with the overall number of trays in the tower and in the stripping columns for a constant operation pressure and a constant amount of stripping steam but there is a limit at which the pressure drop across the trays and the stripping steam requirements make the effectiveness decrease. The use of reboilers in the stripping columns adjacent to the main tower allows an increase in the effectiveness basically due to a greater heat integration. Finally, the increase in the operation pressure of the tower produces an increase of the effectiveness but also an increase in the stripping steam requirements

Complete nutrient recovery from source-separated urine by nitrification and distillation.

Science.gov (United States)

Udert, K M; Wächter, M

2012-02-01

In this study we present a method to recover all nutrients from source-separated urine in a dry solid by combining biological nitrification with distillation. In a first process step, a membrane-aerated biofilm reactor was operated stably for more than 12 months, producing a nutrient solution with a pH between 6.2 and 7.0 (depending on the pH set-point), and an ammonium to nitrate ratio between 0.87 and 1.15 gN gN(-1). The maximum nitrification rate was 1.8 ± 0.3 gN m(-2) d(-1). Process stability was achieved by controlling the pH via the influent. In the second process step, real nitrified urine and synthetic solutions were concentrated in lab-scale distillation reactors. All nutrients were recovered in a dry powder except for some ammonia (less than 3% of total nitrogen). We estimate that the primary energy demand for a simple nitrification/distillation process is four to five times higher than removing nitrogen and phosphorus in a conventional wastewater treatment plant and producing the equivalent amount of phosphorus and nitrogen fertilizers. However, the primary energy demand can be reduced to values very close to conventional treatment, if 80% of the water is removed with reverse osmosis and distillation is operated with vapor compression. The ammonium nitrate content of the solid residue is below the limit at which stringent EU safety regulations for fertilizers come into effect; nevertheless, we propose some additional process steps that will increase the thermal stability of the solid product. Copyright © 2011 Elsevier Ltd. All rights reserved.

Simultaneous Distillation Extraction of Some Volatile Flavor Components from Pu-erh Tea Samples—Comparison with Steam Distillation-Liquid/Liquid Extraction and Soxhlet Extraction

Directory of Open Access Journals (Sweden)

Xungang Gu

2009-01-01

Full Text Available A simutaneous distillation extraction (SDE combined GC method was constructed for determination of volatile flavor components in Pu-erh tea samples. Dichloromethane and ethyl decylate was employed as organic phase in SDE and internal standard in determination, respectively. Weakly polar DB-5 column was used to separate the volatile flavor components in GC, 10 of the components were quantitatively analyzed, and further confirmed by GC-MS. The recovery covered from 66.4%–109%, and repeatability expressed as RSD was in range of 1.44%–12.6%. SDE was most suitable for the extraction of the anlytes by comparing with steam distillation-liquid/liquid extraction and Soxhlet extraction. Commercially available Pu-erh tea samples, including Pu-erh raw tea and ripe tea, were analyzed by the constructed method. the high-volatile components, such as benzyl alcohol, linalool oxide, and linalool, were greatly rich in Pu-erh raw teas, while the contents of 1,2,3-Trimethoxylbenzene and 1,2,4-Trimethoxylbenzene were much high in Pu-erh ripe teas.

Low temperature destructive distillation

Energy Technology Data Exchange (ETDEWEB)

1938-07-05

A process is given and apparatus is described for the destructive distillation at low temperature of coal, oil shale, and the like by subjection to the action of a stream of hot gases or superhearted steam, flowing in a closed circuit. Subsequent treatment of the distillation residues with a gas stream containing oxygen results in combustion of the carbon-containing material therein brings to a high temperature the solid residue, in which the process comprises subsequently contacting the hot solid residue with the fluid stream effecting the distillation.

Production of bio-fuel ethanol from distilled grain waste eluted from Chinese spirit making process.

Science.gov (United States)

Tan, Li; Sun, Zhaoyong; Zhang, Wenxue; Tang, Yueqin; Morimura, Shigeru; Kida, Kenji

2014-10-01

Distilled grain waste eluted from Chinese spirit making is rich in carbohydrates, and could potentially serve as feedstock for the production of bio-fuel ethanol. Our study evaluated two types of saccharification methods that convert distilled grain waste to monosaccharides: enzymatic saccharification and concentrated H2SO4 saccharification. Results showed that enzymatic saccharification performed unsatisfactorily because of inefficient removal of lignin during pretreatment. Concentrated H2SO4 saccharification led to a total sugar recovery efficiency of 79.0 %, and to considerably higher sugar concentrations than enzymatic saccharification. The process of ethanol production from distilled grain waste based on concentrated H2SO4 saccharification was then studied. The process mainly consisted of concentrated H2SO4 saccharification, solid-liquid separation, decoloration, sugar-acid separation, oligosaccharide hydrolysis, and continuous ethanol fermentation. An improved simulated moving bed system was employed to separate sugars from acid after concentrated H2SO4 saccharification, by which 95.8 % of glucose and 85.8 % of xylose went into the sugar-rich fraction, while 83.3 % of H2SO4 went into the acid-rich fraction. A flocculating yeast strain, Saccharomyces cerevisiae KF-7, was used for continuous ethanol fermentation, which produced an ethanol yield of 91.9-98.9 %, based on glucose concentration.

Distilling bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Forrest, C N; Hayden, H P

1926-12-28

Bituminous materials such as heavy asphaltic residues from petroleum distillation or natural bitumens such as gilsonite, grahamite, etc. are distilled in presence of a carrier consisting of pieces of inert refractory material and by the heat generated by combustion of the coke which remains on the carrier after distillation. A vertical cylindrical retort, in which a wood and coal fire is first made, is charged with an inert refractory substance such as pumice stone, broken firebrick, burnt fire clay, carborundum, ash, etc. mixed with a bituminous substance, which, if fusible, may be melted and added in a rotary drum. The mixture passes downwards through the retort, first through regions in which the hydrocarbons are distilled and cracked and then through a region in which the remaining carbon is burnt by a limited supply of air and steam admitted through a grate. The inert material is discharged through a water seal and used again. Vapors, withdrawn from the retort though an outlet, pass through a heat intercharger and separator and are treated with a spray of sulfuric acid to separate ammonia in a scrubber, with water sprays to condense oil in scrubbers, and with oil in a scrubber.

Cyclic distillation technology - A mini-review

DEFF Research Database (Denmark)

Bîldea, Costin Sorin; Pătruţ, Cătălin; Jørgensen, Sten Bay

2016-01-01

Process intensification in distillation systems has received much attention during the pastdecades, with the aim of increasing both energy and separation efficiency. Varioustechniques, such as internal heat-integrated distillation, membrane distillation, rotating packedbed, dividing-wall columns...

Techno-economic assessment of hybrid extraction and distillation processes for furfural production from lignocellulosic biomass.

Science.gov (United States)

Nhien, Le Cao; Long, Nguyen Van Duc; Kim, Sangyong; Lee, Moonyong

2017-01-01

hybrid sequence was more favorable than the traditional distillation process when the methanol fraction of the feed stream was <3% and more benefit could be obtained when that fraction decreased.

40 CFR Table 6 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Solvents and Solvent Blends

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Metal Cans Pt. 63, Subpt. KKKK, Table 6 Table 6 to Subpart KKKK of Part 63—Default Organic HAP Mass... blend CAS. No. Averageorganic HAP mass fraction Typical organic HAP, percent by mass 1. Toluene 108-88-3...

Site-specific and multielement approach to the determination of liquid-vapor isotope fractionation parameters. The case of alcohols

International Nuclear Information System (INIS)

Moussa, I.; Naulet, N.; Martin, M.L.; Martin, G.J.

1990-01-01

Isotope fractionation phenomena occurring at the natural abundance level in the course of liquid-vapor transformation have been investigated by using the SNIF-NMR method (site-specific natural isotope fractionation studied by NMR) which has a unique capability of providing simultaneous access to fractionation parameters associated with different molecular isotopomers. This new approach has been combined with the determination of overall carbon and hydrogen fractionation effects by isotope ratio mass spectrometry (IRMS). The results of distillation and evaporation experiments of alcohols performed in technical conditions of practical interest have been analyzed according to the Rayleigh-type model. In order to check the performance of the column, unit fractionation factors were measured beforehand for water and for the hydroxylic sites of methanol and ethanol for which liquid-vapor equilibrium constants were already known. Inverse isotope effects are determined in distillation experiments for the overall carbon isotope ratio and for the site-specific hydrogen isotope ratios associated with the methyl and methylene sites of methanol and ethanol. In contrast, normal isotope effects are produced by distillation for the hydroxylic sites and by evaporation for all the isotopic ratios

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Young, W

1877-03-29

The method consists in agitating or circulating the distillation products inside the retort by means of jets of gas, steam, or vapor, or by means of reciprocating pistons; condensing certain of the heavy hydrocarbons; sealing or luting the doors of retorts or distilling-vessels; and conducting the distillation for the manufacture of oil so that the charging or discharging doors may be fitted with self-sealing lids. Several arrangements are shown and described; a single horizontal retort is divided into two compartments by a perforated plate which supports the coal, shale, or other bituminous substance, beneath which a piston is reciprocated or a jet of steam, gas, or vapor injected; a vertical retort is fitted with a central tube into which steam, gas, or vapor is injected, or it may be divided into two compartments and the jet injected into one of these; a pair of vertical retorts are connected by a horizontal passage at the top and bottom, and into the upper one steam, gas, or vapor is injected, or the lower one is fitted with a piston.

Interleukin-6 and Cyclooxygenase-2 downregulation by fatty-acid fractions of Ranunculus constantinopolitanus.

Science.gov (United States)

Fostok, Sabreen F; Ezzeddine, Rima A; Homaidan, Fadia R; Al-Saghir, Jamal A; Salloum, Ralph G; Saliba, Najat A; Talhouk, Rabih S

2009-11-16

Medicinal plants represent alternative means for the treatment of several chronic diseases, including inflammation. The genus Ranunculus, a representative of the Ranunculaceae family, has been reported to possess anti-inflammatory, analgesic, antiviral, antibacterial, antiparasitic and antifungal activities, possibly due to the presence of anemonin and other. Different studies have shown the occurrence of unusual fatty acids (FAs) in Ranunculaceae; however, their therapeutic role has not been investigated. The purpose of this study is to characterize potential anti-inflammatory bioactivities in Ranunculus constantinopolitanus D'Urv., traditionally used in Eastern Mediterranean folk medicine. The aerial part of R. constantinopolitanus was subjected to methanol (MeOH) extraction and solvent fractionation. The bioactive fraction (I.2) was further fractionated using column chromatography, and the biologically active subfraction (Y2+3) was identified using infrared (IR) spectroscopy, nuclear magnetic resonance (NMR) and gas chromatography-mass spectrometry (GC-MS). The effects of I.2 and Y2+3 on cell viability were studied in mouse mammary epithelial SCp2 cells using trypan blue exclusion method. To study the anti-inflammatory activities of I.2 and Y2+3, their ability to reduce interleukin (IL)-6 levels was assessed in endotoxin (ET)-stimulated SCp2 cells using enzyme-linked immunosorbent assay (ELISA). In addition, the ability of Y2+3 to reduce cyclooxygenase (COX)-2 expression was studied in IL-1-treated mouse intestinal epithelial Mode-K cells via western blotting. Data were analyzed by one-way analysis of variance (ANOVA), Student-Newman-Keuls (SNK), Tukey HSD, two-sample t-test and Dunnett t-tests for multiple comparisons. The chloroform fraction (I.2) derived from crude MeOH extract of the plant, in addition to Y2+3, a FA mix isolated from this fraction and containing palmitic acid, C18:2 and C18:1 isomers and stearic acid (1:5:8:1 ratio), reduced ET-induced IL-6

Interleukin-6 and Cyclooxygenase-2 downregulation by fatty-acid fractions of Ranunculus constantinopolitanus

Directory of Open Access Journals (Sweden)

Al-Saghir Jamal A

2009-11-01

Full Text Available Abstract Background Medicinal plants represent alternative means for the treatment of several chronic diseases, including inflammation. The genus Ranunculus, a representative of the Ranunculaceae family, has been reported to possess anti-inflammatory, analgesic, antiviral, antibacterial, antiparasitic and antifungal activities, possibly due to the presence of anemonin and other. Different studies have shown the occurrence of unusual fatty acids (FAs in Ranunculaceae; however, their therapeutic role has not been investigated. The purpose of this study is to characterize potential anti-inflammatory bioactivities in Ranunculus constantinopolitanus D'Urv., traditionally used in Eastern Mediterranean folk medicine. Methods The aerial part of R. constantinopolitanus was subjected to methanol (MeOH extraction and solvent fractionation. The bioactive fraction (I.2 was further fractionated using column chromatography, and the biologically active subfraction (Y2+3 was identified using infrared (IR spectroscopy, nuclear magnetic resonance (NMR and gas chromatography-mass spectrometry (GC-MS. The effects of I.2 and Y2+3 on cell viability were studied in mouse mammary epithelial SCp2 cells using trypan blue exclusion method. To study the anti-inflammatory activities of I.2 and Y2+3, their ability to reduce interleukin (IL-6 levels was assessed in endotoxin (ET-stimulated SCp2 cells using enzyme-linked immunosorbent assay (ELISA. In addition, the ability of Y2+3 to reduce cyclooxygenase (COX-2 expression was studied in IL-1-treated mouse intestinal epithelial Mode-K cells via western blotting. Data were analyzed by one-way analysis of variance (ANOVA, Student-Newman-Keuls (SNK, Tukey HSD, two-sample t-test and Dunnett t-tests for multiple comparisons. Results The chloroform fraction (I.2 derived from crude MeOH extract of the plant, in addition to Y2+3, a FA mix isolated from this fraction and containing palmitic acid, C18:2 and C18:1 isomers and stearic acid

Chromatographic finger print analysis of anti-inflammatory active extract fractions of aerial parts of Tribulus terrestris by HPTLC technique.

Science.gov (United States)

Mohammed, Mona Salih; Alajmi, Mohamed Fahad; Alam, Perwez; Khalid, Hassan Subki; Mahmoud, Abelkhalig Muddathir; Ahmed, Wadah Jamal

2014-03-01

To develop HPTLC fingerprint profile of anti-inflammatory active extract fractions of Tribulus terrestris (family Zygophyllaceae). The anti-inflammatory activity was tested for the methanol and its fractions (chloroform, ethyl acetate, n-butanol and aqueous) and chloroform extract of Tribulus terrestris (aerial parts) by injecting different groups of rats (6 each) with carrageenan in hind paw and measuring the edema volume before and 1, 2 and 3 h after carrageenan injection. Control group received saline i.p. The extracts treatment was injected i.p. in doses of 200 mg/kg 1 h before carrageenan administration. Indomethacin (30 mg/kg) was used as standard. HPTLC studies were carried out using CAMAG HPTLC system equipped with Linomat IV applicator, TLC scanner 3, Reprostar 3, CAMAG ADC 2 and WIN CATS-4 software for the active fractions of chloroform fraction of methanol extract. The methanol extract showed good antiedematous effect with percentage of inhibition more than 72%, indicating its ability to inhibit the inflammatory mediators. The methanol extract was re-dissolved in 100 mL of distilled water and fractionated with chloroform, ethyl acetate and n-butanol. The four fractions (chloroform, ethyl acetate, n-butanol and aqueous) were subjected to anti-inflammatory activity. Chloroform fraction showed good anti-inflammatory activity at dose of 200 mg/kg. Chloroform fraction was then subjected to normal phase silica gel column chromatography and eluted with petroleum ether-chloroform, chloroform-ethyl acetate mixtures of increasing polarity which produced 15 fractions (F1-F15). Only fractions F1, F2, F4, F5, F7, F9, F11 and F14 were found to be active, hence these were analyzed with HPTLC to develop their finger print profile. These fractions showed different spots with different Rf values. The different chloroform fractions F1, F2, F4, F5, F7, F9, F11 and F14 revealed 4, 7, 7, 8, 9, 7, 7 and 6 major spots, respectively. The results obtained in this experiment

Cyclic distillation technology - A mini-review

NARCIS (Netherlands)

Bîldea, Costin Sorin; Pătruţ, Cătălin; Jørgensen, Sten Bay; Abildskov, Jens; Kiss, Anton A.

2016-01-01

Process intensification in distillation systems has received much attention during past decades, with the aim of increasing both energy and separation efficiency. Various techniques, such as internal heat-integrated distillation, membrane distillation, rotating packed bed, dividing-wall columns and

Sulfur and selenium isotope separation by distillation

International Nuclear Information System (INIS)

Mills, T. R.; McInteer, B. B.; Montoya, J. G.

1988-01-01

Sulfur and selenium isotopes are used for labeled compounds and as precursors for radioisotope production; however, both limited availability and high costs are problems. A new method is needed for large-scale separation of these isotopes. Experimental distillation columns were used to measure isotopic separations for sulfur and selenium compounds. The maximum total isotope separation of 32 S vs. 34 S were 1.127 for H 2 S, 1.048 for COS, 0.838 for SF 4 , and 1.058 for CH 3 SH. Relative volatilities of 32 S vs. 34 S are 1.0006 for COS and 0.9976 for SF 4 . There is a reverse isotope effect for carbon in COS. No isotopic separation was observed for dimethyl selenide. The lower mass selenium isotopes in H 2 Se are more volatile. Distillation is a promising method for separating sulfur isotopes on a production scale. Existing distillation technology produced separated isotopes with an effect similar to that found for sulfur in SF 4 . 8 refs., 2 tabs

Sulfur and selenium isotope separation by distillation

International Nuclear Information System (INIS)

Mills, T.R.; McInteer, B.B.; Montoya, J.G.

1989-01-01

Sulfur and selenium isotopes are used for labeled compounds and as precursors for radioisotope production; however, both limited availability and high costs are problems. A new method is needed for large-scale separation of theses isotopes. Experimental distillation columns were used to measure isotopic separations for sulfur and selenium compounds. The maximum total isotope separations of 32 S vs. 34 S were 1.127 for H 2 S, 1.048 for COS, 0.838 for SF 4 , and 1.058 for CH 3 SH. Relative volatilities of 32 S and 34 S are 1.0006 for COS and 0.9976 for SF 4 . There is a reverse isotope effect for carbon in COS. No isotopic separation was observed for dimethyl selenide. The lower mass selenium isotopes in H 2 Se are more volatile. Distillation is a promising method for separating sulfur isotopes on a production scale. Existing distillation technology produces separated isotopes with an effect similar to that found for sulfur in SF 4 . (author). 8 refs.; 2 tabs

Electron-beam mediated dry distillation of lignin

International Nuclear Information System (INIS)

Chulkov, V.N.; Bludenko, A.V.; Ponomarev, A.V.

2007-01-01

Radiation heating was studied for its application in dry distillation of lignin under high absorbed-dose irradiation with no supplementary heating device used. Commercial preparation Polyphepan containing lignin (90 wt.%) and cellulose (10 wt.%), dried at 102 deg C, was used. The test samples were exposed to 8 MeV electron beams on U-003 linear accelerator under atmospheric pressure, with dose rates of 3.6 and 4.8 kGy/s. It is demonstrated that an increased yield of liquid products of dry lignin distillation is observed under conditions studied with a two-fold decrease in energy consumption due to more favorable heating conditions and intensification of free-radical reactions [ru

OPTIMIZATION OF PATCHOULI OIL (POGOSTEMON CABLIN, BENTH WITH STEAM DISTILLATION ASSISTED BY PULSED ELECTRIC FIELD VIA RESPONSE SURFACE METHODOLOGY

Directory of Open Access Journals (Sweden)

SUKARDI

2017-08-01

Full Text Available The study was aimed to determine the role of pulsed electric field (PEF treatment before hydro-distillation of the patchouli oil. Response Surface Methodology (RSM was employed to optimize PEF treatment (voltages, frequencies and times of distillation of patchouli oil from dried patchouli crops. The experimental design and analysis the result to obtain the optimal processing parameters was a Box-Behnken Design (BBD. Three variables were examined in this study: voltages (1,000-2,000 volt; frequencies (1,000-2,000 Hz; and distillation time (4-8 hours. The results showed that the voltage greatly affects the volume of patchouli oil obtained and optimum condition of PEF was voltages of 2,000 volts, frequencies of 1,874 Hz, and 8 hours distillation. The patchouli oil obtained is 8.037 ml of 300 g of dry material (±2.7%. The verification of the model shows that 96.6% (7.76±0.15 ml can adequately for reflecting the expected optimization.

Changes in the phenolic acid content during commercial dry-grind processing of corn to ethanol and DDGS

Science.gov (United States)

Nine fractions (ground corn-1, cooked slurry-2, liquefied slurry-3, fermented mash-4, whole stillage-5, thin stillage-6, condensed distillers soluble (CDS)-7, distillers wet grains (DWG)-8, and distillers dried grains with solubles (DDGS)-9) were collected from three commercial dry-grind bioethanol ...

Hydrotreatment of middle distillate derived from Australian brown coal (Part 1)

Energy Technology Data Exchange (ETDEWEB)

Miki, Keiji; Yamamoto, Yoshitaka; Saito, Ikuo; Sato, Yoshiki

1987-12-20

Analysis of the composition of liquefied brown coal and changes in composition of oil hydrogenated with 3 kinds of catalysts were studied. Distillates at b.p. 200/420/sup 0/C obtained by the liquefaction of Australian and Victorian brown coals were used as samples. The hydrodenitrogenation (HDN) rates of the hydrotreated oils were 60% for NiMo, 51.9% for CoMo and 57.8% for NiW. The oil from the first stage liquefaction contained phenols of about 21 wt% as its acidic components. In the autoclave treatment under the reaction temperature of 370/sup 0/C and hydrogen pressure of 100 kg/cm/sup 2/G for 1 hour reaction time, it was difficult with any of the catalysts to remove all the phenols. The HDN activities of the catalysts were in the sequence of NiMo>NiW>CoMo, and the phenol conversion rates were in the sequence of NiMo>CoMo>NiW. NiW was less active for hydrogenation and hydrodeoxygenation reaction of phenols in contrast with the high HDM activity. (2 figs, 6 tabs, 14 refs)

Preparation of fuels and chemical products from mixtures of coal and petroleum

Energy Technology Data Exchange (ETDEWEB)

Krichko, A A; Yulin, M K

1973-01-01

The distillate to 320/sup 0/C from the liquid phase hydrogenation of a 1 : 1 coal-Arlan petroleum mixture was processed to yield phenols 3.4 percent, high aromatics gasoline 81.2 percent, C/sub 1/--C/sub 4/ alkanes 13.5 percent, H/sub 2/S 0.5 percent, and water 1.0 percent. Thus, C/sub 6/--C/sub 8/ phenols were separated from the fraction distilling to 240/sup 0/C, and the phenol-free fraction and the 240 to 320/sup 0/C fraction were hydrofined over an aluminum-cobalt-molybdenum catalyst at 400/sup 0/C and 50 atm. Distillation gave a gasoline fraction, which was reformed, and a 180 to 320/sup 0/C fraction, which was hydrocracked at 380/sup 0/C and 40 atm on a zeolite catalyst.

Ethanol dehydration via azeotropic distillation with gasoline fraction mixtures as entrainers: A pilot-scale study with industrially produced bioethanol and naphta

OpenAIRE

Gomis Yagües, Vicente; Pedraza Berenguer, Ricardo; Saquete Ferrándiz, María Dolores; Font, Alicia; Garcia-Cano, Jorge

2015-01-01

Various hydrocarbons (n-hexane, cyclohexane, toluene, isooctane) and mixtures of them (binary, ternary or quaternary), as well as two different types of industrially produced naphtha (one obtained by direct distillation and the other from a catalytic cracking process), have been tested as candidate entrainers to dehydrate ethanol. The tests were carried out in an azeotropic distillation column on a semi pilot plant. The results show that it is possible to dehydrate bioethanol using naphtha as...

Improvement of solar ethanol distillation using ultrasonic waves

Directory of Open Access Journals (Sweden)

Jaruwat Jareanjit

2016-08-01

Full Text Available This report presents a study on the use of ultrasonic waves in solar ethanol distillation to investigate the performance of ultrasonic waves at a frequency of 30 kHz and at 100 Watts that were installed in the inlet area of a 10-litre distillation tank. Based on the non-continuous distillation process (batch distillation, the experiment demonstrated that using ultrasonic waves in solar ethanol distillation caused the average concentration of hourly distilled ethanol to be higher than that of a normal system (solar ethanol distillation without ultrasonic wave at the same or higher distillation rate and hourly distillation volume. The ultrasonic wave was able to enhance the separation of ethanol from the solution (water-ethanol mixture through solar distillation. The amount of pure ethanol product from each distilled batch was clearly larger than the amount of product obtained from a normal system when the initial concentration of ethanol was lower than 50%v/v (% by volume, where an average of approximately 40% and 20% are obtained for an initial ethanol concentration of 10%v/v and 30%v/v, respectively. Furthermore, the distillation rate varied based on the solar radiation value.

Ionic liquid screening for ethylbenzene/styrene separation by extractive distillation

NARCIS (Netherlands)

Jongmans, M.T.G.; Schuur, B.; Haan, de A.B.

2011-01-01

The separation of ethylbenzene from styrene by distillation is very energy-intensive, because of the low relative volatility (1.3–1.4). Extractive distillation is a promising alternative to separate the close boiling mixture, in which the solvent selection is crucial for the process feasibility. In

Method of distillation of alum shale

Energy Technology Data Exchange (ETDEWEB)

Hultman, G H

1920-02-03

A method is given of distilling alum shale by means of preheated gases obtained from the process of distillation in which the gases are circulating within a system consisting of the retort, the condensation apparatus, and generator, each separate. It is characterized by leading the gases produced during the distillation through a condensation apparatus for separation of the condensable products, such as oil, benzene, ammonia, and sulfur, and the noncondensable gases are conveyed through one or more heated generators that have been charged with residue from the process of distillation (any superfluous amount of gas formed during the process being released). The heated gases are thereupon passed to the retort for completion of the distillation process.

Method of distillation of bituminous material

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, E G.T.

1919-11-12

A method is described of dry distillation of bituminous materials by leading warm combustible gases, mixed or not mixed with steam, through the distillation chamber in direct contact with the materials, during which process the distillation chamber may be heated by other means. It is characterized by the mixture of distillation products (formed by the vapors produced by heating the raw materials) and the gas (circulating gas) used for heating in the process, being led through coolers or similar contrivances, in order to separate through condensation the greater part of the content of the products or materials condensable at ordinary temperatures, and also to recover as much as possible of the highly volatile oils in the gas. Thereafter the gas is split, one part is, without further cleaning, and led through the distillation chamber, after this gas has been reheated in suitable apparatus. The other part (surplus gas), which in volume corresponds approximately to the new-formed distillation gases, is treated according to known methods for the extraction of the remaining products of the distillation, such as volatile oils, ammonia, methyl alcohol, sulfuretted hydrogen, and others. The patent contains three other claims.

The Isolation of Sitronellal and Rhodinol from Lemongrass Oil Using Vacuum Distillation Fractination

Directory of Open Access Journals (Sweden)

Fitriana Djafar

2010-06-01

Full Text Available The main componenet of lemongrass oil that is sitronellal and rhodinol (sitronellol and geraniol was isolated by using vacuum of distillation fraksinasi. Variably the research included the variable continue to, that is the sample weight (300 mL and process time (4 hours; and the variable changed, that is the pressure (80, 95 and 100 mbar and the temperature (145, 150, and 160o C. Results of the analysis of the ras material showed that lemongrass oil that came from Kota Panjang, Gayo Lues, Province Aceh had the content sitronellal that was high that is of 51.067% and rhodinol of 30.761%. The characteristics from lemongrass oil was yellow faded, the ray index 1.466, the specific gravity 0.889 solubility in alcohol 1:1 clear and the round of optics 19.15. The distillation sitronellal, 28.87% rhodinol (22.60% geraniol and 6.27% sitronellol and 11% other component. The condition for the process that was good enough in the isolation sitronellol used distillation vacuum of fraksinasi with the temperature and the pressure that were low that is 145o C and 80 mbar. The condition for the process that was quite good in the isolation rhodinol was use to use vacuum of distillation fraksinasi in the temperature and the pressure that were not too high and or low that is 150o C and 95 mbar.

The incorporation of [1-14C] acetate into the methyl ketones that occur in steam-distillates of bovine milk fat.

Science.gov (United States)

Lawrence, R C; Hawke, J C

1966-01-01

1. The (14)C-labelling of the fatty acids and the methyl ketones in steam-distillates of milk fat from a lactating cow that had been injected intravenously with [1-(14)C]acetate was determined. 2. The labelling patterns of the C(6)-C(16) fatty acids and the corresponding methyl ketones with one fewer carbon atoms were similar, particularly so for the C(5)-C(10) compounds at 9 and 22hr. after the injection of [1-(14)C]acetate. The isolation of (14)C-labelled methyl ketones in the range C(3)-C(15) is evidence that the beta-oxo acid precursors, which are glyceride-bound in the milk fat, are synthesized in the mammary gland from acetate. The absence of heptadecan-2-one in steam-distillates and the extremely low specific radioactivity of stearic acid are further evidence for this biosynthetic pathway. 3. The specific radioactivities of the C(5)-C(15) methyl ketones were higher (with the exception of C(9) methyl ketone in the second milking) than the specific activities of the corresponding fatty acids with one more carbon atom. This is consistent with the methyl ketone precursors' being formed during the biosynthesis of fatty acids rather than being products of beta-oxidation of fatty acids.

Evidence for distillation in the formation of HAL and related hibonite inclusions. [from Allende, Dhajala, and Murchison chondrites

Science.gov (United States)

Ireland, Trevor R.; Zinner, Ernst K.; Fahey, Albert J.; Esat, Tezer M.

1992-01-01

New Ca- and Ti-isotopic analyses of DH-H1, 7-404, and 7-971, and Mg-isotopic analyses on DH-H1 and 7-404 are reported. O-isotopic analyses of HAL, 7-404, 7-971, and a variety of other refractory inclusions from Murchison were made in order to establish the presence or absence of FUN O-isotopic systematics. A higonite-rich residue produced by the evaporation of kaersutite was analyzed for its trace-element and isotopic abundances to see if any of the characteristics of FUN hibonite inclusions can be produced by distillation in the laboratory. These data are then used to evaluate for all four inclusions the HAL-type formation models originally proposed by Allen et al. (1980) and Lee et al. (1980). The four inclusions were found to have very similar chemical and isotopic features. All are characterized by large Ce depletions and very low Mg, Ti, and V concentrations compared to other meteoritic hibonites. All four inclusions have delta(C-48) within error of -5 per mil. Ca-, Ti-, and O-isotopic compositions are fractionated with enrichments of the heavy isotopes, and the Ti-isotopic mass fractionation is inversely correlated with Ti concentration. It is concluded that the inclusions formed primarily as distillation residues in accord with the early conclusions.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Newton, A V

1856-04-22

In order to obtain, at the first distillation, from coal, shale, and bituminous substances an oil sufficiently pure for illuminating and other purposes, the material broken into very small pieces and placed on the bottom of the retort, is evenly covered with common sand, about four times greater in weight than the weight of the coal. The coal and sand are then gradually raised to a temperature of 212/sup 0/F. Steam containing carbonaceous impurities first passes to the condenser, and subsequently oil, which rises to the surface of the water in the receiving-vessel. When some bituminous substances are employed, the temperature, after oil ceases to come over, may be gradually raised until the oil produced ceases to be pure. Most kinds of clay and earth, chalk, gypsum, black oxide of manganese, plumbago, or charcoal may be used separately, in combination, or with added chemicals, instead of sand as the medium for filtering the gas or vapor from which the oil is formed. Either the oil obtained by the first distillation or oils obtained by other means may be rectified by distilling with sand.

Fabric protectors. Part II - Propane, 1,1,1-trichloroethane, and petroleum distillates levels in air after application of fabric protectors.

Science.gov (United States)

Otson, R; Williams, D T; Bothwell, P D

1984-01-01

Propane, 1,1,1-trichloroethane, and petroleum distillates levels in air which were generated during the use of aerosol type fabric protectors were monitored by means of the NIOSH charcoal tube, a glass bulb grab sampling, and the GASBADGE passive device techniques. Although 1982 ACGIH TLV-STEL were readily exceeded in an unventilated test room, when fabric was sprayed with 450 g of fabric protector in an unconfined area within a home the generated vapors quickly dispersed and STEL and 8-hour TWA-TLV were not exceeded.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bell, T

1863-09-14

Shales and other bituminous minerals are distilled in horizontal retorts arranged side by side and with furnaces beneath their front ends. The furnace gases pass, preferably through a brickwork grating, into spaces between the retorts and beneath a horizontal partition towards the back ends. They return above the partition to the front of the retorts, and finally enter a horizontal flue leading to a chimney. The front end of each retort is fitted with a hopper for charging and with a door for discharging. The products of distillation pass through perforated partitions inside the retorts and are conveyed away by pipes at the back.

Gels of ferulated arabinoxylans extracted from distillers dried grains with solubles: rheology, structural parameters and microstructure

Science.gov (United States)

One of the major by-products of bioethanol production is distillers dried grains with solubles (DDGS). Maize is one of the main sources for the production of this biofuel. In this way, dietary fiber represents the principal fraction of DDGS, which could be a potential source of added-value biomolecu...

A review of the FT distillate pathway in GHGenius

International Nuclear Information System (INIS)

2006-01-01

Fischer-Tropsch (FT) distillates products are now used throughout the world as a commercial fuel. However, lifecycle greenhouse gas (GHG) emissions from FT distillates fuels are higher than diesel fuel produced from crude oil. This paper provided details of a lifecycle analysis of FT distillates pathways created for GHGenius, a model used to analyze emissions from a variety of combustion sources. The study examined values reported in tests conducted by major oil and gas operators and described the conversion technologies typically used at FT distillates production facilities. Summaries of reports on FT distillates emissions were also provided. Three primary factors were identified that contributed to different results reported for FT distillates emissions: (1) the efficiency of the conversion process; (2) the allocation procedure used in the conventional oil refinery for the emissions of individual products; and (3) the emissions associated with natural gas production. The GHGenius model was used to quantify the impact of the 3 main factors. An alternative system expansion methodology was used to compare crude oil diesel pathways with a high efficiency, low gas leak scenario in order to achieve high values reported by some oil and gas operators. 5 refs., 5 tabs., 5 figs

Towards comprehensive hydrocarbons analysis of middle distillates by LC-GCxGC.

Science.gov (United States)

Adam, Frédérick; Bertoncini, Fabrice; Thiébaut, Didier; Esnault, Sébastien; Espinat, Didier; Hennion, M C

2007-01-01

The detailed characterization of middle distillates is essential for a better understanding of reactions involved in refining processes. Owing to a higher resolution power and an enhanced sensitivity, but especially to a group-type ordering in the chromatographic plane, comprehensive two-dimensional gas chromatography (GCxGC) offers unsurpassed characterization possibilities for petroleum samples. However, GCxGC fails to totally discriminate naphthenes from unsaturates occurring in hydrotreated diesel samples. This article aims at promoting the implementation of LC-GCxGC for the quantitative determination of hydrocarbon distribution in middle distillates, including naphthenes. In this configuration, liquid chromatography (LC) enables the separation of hydrocarbons into two fractions (viz., saturated and unsaturated) before the subsequent analysis of each fraction by GCxGC. In this paper, the choice of GCxGC conditions in order to achieve the separation and identification of hydrocarbons by chemical class is discussed; under these conditions, naphthenes are separated according to the number of saturated rings. For the first time, the presence of di-, tri-, and tetra-naphthenes resulting from the hydroconversion of aromatics can clearly be evidenced. A quantitative procedure for the determination of the distribution of hydrocarbons, including the distribution of naphthenes according to the number of saturated rings, is also proposed and discussed in detail. LC-GCxGC is found to provide an unequalled degree of information that will widely contribute to a better understanding of hydroconversion processes.

27 CFR 19.830 - Application of distilled spirits tax.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Application of distilled spirits tax. 19.830 Section 19.830 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Production of Vinegar by the...

Results and Interpretation of the WFRD ELS Distillation Down-Select Test Data

Science.gov (United States)

Delzeit, Lance Dean; Flynn, Michael; Carter, Layne; Long, David A.

2010-01-01

Testing of the Wiped-film Rotating-disk (WFRD) evaporator was conducted in support of the Exploration Life Support Distillation Down-Select Test. The WFRD was constructed at NASA Ames Research Center (ARC) and tested at NASA Marshall Space Flight Center (MSFC). The WFRD was delivered to MSFC in September 2009, and testing of solution #1 and solution #2 immediately following. Solution #1 was composed of humidity condensate and urine, including flush water and pretreatment chemicals. Solution #2 was composed of hygiene water, humidity condensate, and urine, including flush water and pretreatment chemicals. During the testing, the operational parameters of the WFRD were recorded and samples of the feed, brine, and product were collected and analyzed. The steady-state results of processing 414L of feed solution #1 and 1283L of feed solution #2 demonstrated that running the WFRD at a brine temperature of 50 C gave an average production rate of 16.7 L/hr. The specific energy consumption was 80.5W-hr/L. Data Analysis shows that the water recovery rates were 94% and 91%, respectively. The total mass of the WFRD as delivered to MSFC was 300 Kg. The volume of the tests stand rack was 1m width x 0.7m depth x 1.9m height or 1.5 cu m of which about half of the total volume is occupied by equipment. Chemical analysis of the distillate showed an average TOC of 20ppm, a pH of 3.5, and a conductivity of 98 mho/cm. The conductivity of the distillate, compared to the feed, decreased by 98.9%., the total ion concentration decreased by 99.6%, the total organics decreased 98.6%, and the metals were at or below detection limits

A PROCESS FOR SEPARATING AZEOTROPIC MIXTURES BY EXTRACTIVE AND CONVECTIVE DISTILLATION

Science.gov (United States)

Frazer, J.W.

1961-12-19

A method is described for separating an azeotrope of carbon tetrachloride and 1,1,2,2-tetrafluorodinitroethane boiling at 60 deg C. The ndethod comnprises, specifically, feeding azeotrope vapors admixed with a non- reactive gas into an extractive distillation column heated to a temperature preferably somewhat above the boiling point of the constant boiling mixture. A solvent, di-n-butylphthalate, is metered into the column above the gas inlet and permitted to flow downward, earrying with it the higher bomling fraction, while the constituent having the lower boiling point passes out of the top of the column with the non-reactive gas and is collected in a nitrogen cold trap. Other solvents which alter the vapor pressure relationship may be substituted. The method is generally applicable to azeotropic mixtures. A number of specific mixtures whicb may be separated are disclosed. (AEC)

Conceptual design of heterogeneous azeotropic distillation process for ethanol dehydration using 1-butanol as entrainer

OpenAIRE

Paritta Prayoonyong

2014-01-01

The synthesis of a heterogeneous azeotropic distillation process for ethanol dehydration using 1-butanol as entrainer is presented. The residue curve map of the ethanol/water/1-butanol mixture is computationally generated using non-random twoliquid thermodynamic model. It is found that 1-butanol leads to a residue curve map topological structure different from that generated by typical entrainers used in ethanol dehydration. Synthesis...

Prospective conceptual qualification of hybrid centrifugation/distillator for 6LI nuclear fusion technology scaled supply demands

International Nuclear Information System (INIS)

Sedano, L.; Herranz, J. L.; Casado, J. L.; Castro, P.; Xiberta, J.

2013-01-01

The change in the demand for exploitation of lithium as a resource appears during the last decade, related to the development of the ion-Li batteries market and with the requirements of Nuclear Fusion fuels (deuterium and lithium) as coming energy option. A prospective analysis of synergistic demands of both markets, in its technical and in its economic aspects appears of prospective interest. The civil market 6 Li/ 7 Li enrichment demand is analyzed. Specific technological developments permitting on-line production according to demand is discussed. A [centrifugation /thermal diffusion / combined distillation] technique is selected and qualified as technologically viable option for scaled production of litiated-forms. A conceptual design of a production plant is finally proposed according to the new technical capability.

Active solar distillation - A detailed review

Energy Technology Data Exchange (ETDEWEB)

Sampathkumar, K.; Pitchandi, P. [Department of Mechanical Engineering, Tamilnadu College of Engineering, Coimbatore 641659, Tamilnadu (India); Arjunan, T.V. [Department of Automobile Engineering, PSG College of Technology, Coimbatore 641004, Tamilnadu (India); Senthilkumar, P. [Department of Mechanical Engineering, KSR College of Engineering, Tiruchengode 637215, Tamilnadu (India)

2010-08-15

All over the world, access to potable water to the people are narrowing down day by day. Most of the human diseases are due to polluted or non-purified water resources. Even today, under developed countries and developing countries face a huge water scarcity because of unplanned mechanism and pollution created by manmade activities. Water purification without affecting the ecosystem is the need of the hour. In this context, many conventional and non-conventional techniques have been developed for purification of saline water. Among these, solar distillation proves to be both economical and eco-friendly technique particularly in rural areas. Many active distillation systems have been developed to overcome the problem of lower distillate output in passive solar stills. This article provides a detailed review of different studies on active solar distillation system over the years. Thermal modelling was done for various types of active single slope solar distillation system. This review would also throw light on the scope for further research and recommendations in active solar distillation system. (author)

Comparative study of the essential oil and hydrolate composition of Lythrum salicaria L. obtained by hydro-distillation and microwave distillation methods

Directory of Open Access Journals (Sweden)

A. Manayi

2014-04-01

Full Text Available Essential oils are considered as very complex natural mixtures containing numerous components at quite various concentrations. Lythrum salicaria has not been previously subjected to examination of its volatile oil. The present study was carried out to evaluate the essential oil composition of the flowering aerial parts of the plant by using conventionally hydro-distillation (HD and microwave assisted hydro-distillation (MAH methods along with the aromatic water obtained by hydro-distillation. Components of these three samples were recognized by GC/MS. Identification of components resulted in recognition of 14 (98% oil, 32 (98.4%, and 10 (95.5% compounds for HD, its hydrolate, and MAH samples, respectively. The predominant constituents in the HD oil were bis (2-ethylhexyl phthalate (29.2%, n-hexadecanoic acid (22%, and pentacosane (9.5%. The major constituents of the hydrolate were elucidated as 2(4H-benzofuranone-5,6,7,7a-tetrahydro-4,4,7a-trimethyl (6.4%, neryl acetone (6%, pentanoic acid (5.7%, nonanoic acid (5.6%, and octanoic acid (5.5%. Accordingly, bis (2-ethylhexyl phthalate (43.2%, methyl-cyclopentane (36.5%, and pentacosane (4.7% were assessed as the main components of MAH oil. Comparing the three samples compositions, it was concluded that the extraction procedure led to variations in quality and quantity of volatiles. Besides, bis (2-ethylhexyl phthalate, the common plasticizer, was identified as the main pollutant in both HD and MAH oils. The presence of this substance in the oils provided the evidence of contaminations that was absorbed from water into the plant suggesting GC/MS as a suitable method for its detection in plant materials.

THE EFFECT OF DISTILLATE STORING DISTILLED FROM FRUCTOSE SYRUPS TOWARD ITS ACETALDEHYDE CONCENTRATION MEASURED BY GAS CHROMATOGRAPHY

Directory of Open Access Journals (Sweden)

Maria Monica Sianita Basukiwardojo

2010-06-01

Full Text Available Acetaldehyde is a compound of aldehyde group that is very volatile and toxic. This compound can be found in fructose syrups used in carbonate beverages. The syrups had been distilled then analysed using gas chromatography. The concentration of acetaldehyde was 289.78 g/g in the distillates kept for one week, 295.30 g/g in those kept for two weeks, 429.45 g/g in those kept for three weeks, and 449.38 g/g in those kept for four weeks. The optimum column temperature was programmed with initial temperature of 40 oC held on for four minutes, then increasing by 40 oC/minute to 200 oC. It can be concluded that the longer the distillates have been kept, the greater the concentration of acetaldehyde in the distillates. A further research to investigate the present of microbe in the distillates and the effect of pH should be conducted   Keywords: acetaldehyde, fructose syrup, distillates, gas chromatography.

Distillation of Essential Oils from Pontianak Orange Peel Wastes and Its Utilization for Aromatherapy Soap

Directory of Open Access Journals (Sweden)

Hidayati Hidayati

2012-12-01

Full Text Available Orange (Citrus nobilis var. microcarpa is the main commodities in Pontianak. Production of essential oils from orange peel wastes and its use for soap aromatherapy substance could improve its economic value. This study is aimed to produce the essential oils from orange peel wastes with the highest limonene content by distillation. Its application for aromatherapy soap substance also evaluated. Distillation of essential oils from orange peels was performed at 1000C and 1100C for 4, 5, 6 and 7 hours. The results showed that at 1000C for 7 hours produced the highest limonene content, reach 97.69%. The essential oils color was pale yellow, specific gravity 0.84, refractive index 1.47, solubility in 90% ethanol 1:1 (transparent, acid value 0.143% and ester number 5.37. The aromatherapy soap produced with addition of 3.6% of limonene oils is in accordance with SNI 06-3532-1994 except for water content parameter.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Neilson, A; Renfrewshire, I; Black, W

1889-06-14

The invention relates to a method of, and apparatus for, distilling shale, coal, or other oil or tar-yielding minerals, to obtain gases, liquids, or other products. The distillation is effected in vertical retorts by the combustion of the partially spent material in the lower part of the retorts, to which steam and air are admitted. The retorts are built of firebrick, and provided with iron casings. They are fed through hoppers and discharged through the openings. The discharging is facilitated by a cone, or its equivalent, in the base of each retort. Steam and air are admitted through the pipes. The interior may be viewed through holes. The products are taken off from the space around the hopper.

Separation of free fatty acids from high free fatty acid crude palm oil using short-path distillation

Science.gov (United States)

Japir, Abd Al-Wali; Salimon, Jumat; Derawi, Darfizzi; Bahadi, Murad; Yusop, Muhammad Rahimi

2016-11-01

The separation of free fatty acids (FFAs) was done by using short-path distillation (SPD). The separation parameters was at their boiling points, a feed amount of 2.3 mL/min, an operating pressure of 10 Torr, a condenser temperature of 60°C, and a rotor speed of 300 rpm. The physicochemical characteristics of oil before and after SPD were determined. The results showed that FFA % of 8.7 ± 0.3 and 0.9 ± 0.1 %, iodine value of 53.1 ± 0.4 and 52.7 ± 0.5 g I2/100 g, hydroxyl value of 32.5 ± 0.6 and 13.9 ± 1.1 mg KOH/g, unsaponifiable value of 0.31 ± 0.01 and 0.20 ± 0.15%, moisture content of 0.31 ± 0.01 and 0.24 ± 0.01 % for high free fatty acid crude palm oil before and after distillation, respectively. Gas chromatography (GC) results showed that the major fatty acids in crude palm oil (CPO) were palmitic acid (44.4% - 45%) followed by oleic acid (39.6% - 39.8%). In general, high free fatty acid crude palm oil after molecular distillation (HFFA-CPOAM) showed admirably physicochemical properties.

Comparison of patient-reported acute urinary and sexual toxicity scores in a 6- versus 2-fraction course of high-dose-rate prostate brachytherapy monotherapy

International Nuclear Information System (INIS)

Ragab, Omar; Park, Sang-June; Zhang, Mingle; Wang, Jason; Velez, Maria; Demanes, David J.; Banerjee, Robyn; Patel, Shyamal; Kamrave, Mitchell

2018-01-01

To identify differences in acute urinary and sexual toxicity between a 6-fraction and 2-fraction high-dose-rate brachytherapy monotherapy regimen and correlate dosimetric constraints to short-term toxicity. A single institution retrospective study of 116 men with prostate cancer treated with HDR monotherapy from 2010 to 2015 was conducted. Eighty-one men had 7.25 Gy × 6-fractions and 35 men had 13.5 Gy × 2-fractions. Patients had two CT-planned implants spaced 1–2 weeks apart. Patient baseline characteristics, International Prostate Symptom Scores (IPSS) and Sexual Health Inventory for Men (SHIM) scores were collected pre-treatment and 3, 6 and 12 months post-implantation. Mixed effect modelling was undertaken to compare baseline, 1–6 month and 7–12 month scores between groups. Poisson regression analysis was performed to correlate dosimetric constraints with acute toxicity. There was no difference between baseline and post-implantation IPSS scores between 6-fraction and 2-fraction groups. SHIM scores for men treated with 6-fractions had a steeper decline at 1–6 months, but resolved at 7–12 months. Pre-treatment alpha-blocker use correlated with worse short-term acute urinary toxicity. Worsened SHIM score correlated with increasing age, diabetes mellitus and androgen-deprivation therapy. In a dosimetric analysis of outcomes, prostate V150 dose and bladder wall (D01.cc, D1cc, D2cc) dose correlated with increased IPSS score. No increased acute genitourinary or sexual dysfunction has been observed in men when transitioning from 6-fraction to 2-fraction HDR monotherapy. A dosimetric correlation was found between the V150 and bladder wall doses for acute urinary toxicity. Future research should continue to standardize and validate dose constraints for prostate HDR monotherapy patients.

Vacuum distillation/vapor filtration water recovery, phases 1 and 2

Science.gov (United States)

Honegger, R. J.; Remus, G. A.; Krug, E. K.

1973-01-01

The research is reported on the development of an evaporator for vacuum distillation/vapor filtration VD/VF water reclamation system for use on manned space flights. The design, fabrication, and tests of a six-man evaporator are described. It is concluded that: (1) A condenser with an internal rotating impeller and coolant surfaces directly opposite the condensing surfaces is an effective condenser. (2) The VD/VF evaporator, catalyst unit and condenser function satisfactorily based on thermal, mechanical and recovery performance during a 145-hour evaluation test. (3) The quality of recovered water, as measured by analyses for total organic carbon, pH, conductivity, turbidity, and viable bacteria density was within established limits for potability.

Purification Simulation With Vapor Permeation and Distillation-Adsorption In Bioethanol Plant

Directory of Open Access Journals (Sweden)

Misri Gozan

2017-04-01

Full Text Available High purity of Bioethanol is required in biofuel mixing with gasoline (EXX. In bioethanol production line, the azeotropic property of ethanol-water becomes the barrier for purification process. This study examined two bioethanol separation processes by support of simulation tools, Superpro Designer 9.0 software. Ethanol purity and a low costeconomical process were the major considerations. Purification method of vapor permeation membrane technology was compared with distillation-adsorption method. Data from previous lab experiments and some literatures were used. The results showed that distillation-adsorption method is more economical compared to vapor permeation technology. Payback period of the simulation is 3.9 years and 4.3 years to distillation adsorption and vapor permeation respectively with each IRR value is 20.23% and 17.89%. Initial investment value of vapor permeation is 9.6% higher than distillation method. Significant difference observed in operating costs, since more units involved in vapor permeation require more labors to operate.

Microbubble Distillation for Ethanol-Water Separation

Directory of Open Access Journals (Sweden)

Atheer Al-yaqoobi

2016-01-01

Full Text Available In the current study, a novel approach for separating ethanol-water mixture by microbubble distillation technology was investigated. Traditional distillation processes require large amounts of energy to raise the liquid to its boiling point to effect removal of volatile components. The concept of microbubble distillation by comparison is to heat the gas phase rather than the liquid phase to achieve separation. The removal of ethanol from the thermally sensitive fermentation broths was taken as a case of study. Consequently the results were then compared with those which could be obtained under equilibrium conditions expected in an “ideal” distillation unit. Microbubble distillation has achieved vapour compositions higher than that which could be obtained under traditional equilibrium conditions. The separation was achieved at liquid temperature significantly less than the boiling point of the mixture. In addition, it was observed that the separation efficiency of the microbubble distillation could be increased by raising the injected air temperature, while the temperature of the liquid mixture increased only moderately. The separation efficiency of microbubble distillation was compared with that of pervaporation for the recovery of bioethanol from the thermally sensitive fermentation broths. The technology could be controlled to give high separation and energy efficiency. This could contribute to improving commercial viability of biofuel production and other coproducts of biorefinery processing.

Efficiency of fermionic quantum distillation

Energy Technology Data Exchange (ETDEWEB)

Herbrych, Jacek W. [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Feiguin, Adrian E. [Northeastern Univ., Boston, MA (United States); Dagotto, Elbio R. [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Heidrich-Meisner, F. [Ludwig-Maximilians-Univ. Munchen, Munchen (Germany)

2017-09-13

Here, we present a time-dependent density-matrix renormalization group investigation of the quantum distillation process within the Fermi-Hubbard model on a quasi-one-dimensional ladder geometry. The term distillation refers to the dynamical, spatial separation of singlons and doublons in the sudden expansion of interacting particles in an optical lattice, i.e., the release of a cloud of atoms from a trapping potential. Remarkably, quantum distillation can lead to a contraction of the doublon cloud, resulting in an increased density of the doublons in the core region compared to the initial state. As a main result, we show that this phenomenon is not limited to chains that were previously studied. Interestingly, there are additional dynamical processes on the two-leg ladder such as density oscillations and self-trapping of defects that lead to a less efficient distillation process. An investigation of the time evolution starting from product states provides an explanation for this behavior. Initial product states are also considered since in optical lattice experiments, such states are often used as the initial setup. We propose configurations that lead to a fast and efficient quantum distillation.

Distilling coal, etc

Energy Technology Data Exchange (ETDEWEB)

Nelson, J

1917-12-21

Coals of various kinds such as shales, bitumens, and oil sand, peat, etc. are distilled at 350 to 450/sup 0/C and in the presence of vapors and gases obtained by cracking hydrocarbon oils, or the gases obtained by separating the condensable hydrocarbons therefrom, and, if desired, with the addition of superheated steam. The hydrocarbons are properly cracked by passing through molten lead as described in Specification 116,304. According to the Provisional Specification, superheated steam alone may be used to effect the distillation.

Biodiesel of distilled hydrogenated fat and biodiesel of distilled residual oil: fuel consumption in agricultural tractor

Energy Technology Data Exchange (ETDEWEB)

Camara, Felipe Thomaz da; Lopes, Afonso; Silva, Rouverson Pereira da; Oliveira, Melina Cais Jejcic; Furlani, Carlos Eduardo Angeli [Universidade Estadual Paulista (UNESP), Jaboticabal, SP (Brazil); Dabdoub, Miguel Joaquim [Universidade de Sao Paulo (USP), Ribeirao Preto (Brazil)

2008-07-01

Great part of the world-wide oil production is used in fry process; however, after using, such product becomes an undesirable residue, and the usual methods of discarding of these residues, generally contaminate the environment, mainly the rivers. In function of this, using oil and residual fat for manufacturing biodiesel, besides preventing ambient contamination, turning up an undesirable residue in to fuel. The present work had as objective to evaluate the fuel consumption of a Valtra BM100 4x2 TDA tractor functioning with methylic biodiesel from distilled hydrogenated fat and methylic biodiesel from distilled residual oil, in seven blends into diesel. The work was conducted at the Department of Agricultural Engineering, at UNESP - Jaboticabal, in an entirely randomized block statistical design, factorial array of 2 x 7, with three repetitions. The factors combinations were two types of methylic distilled biodiesel (residual oil and hydrogenated fat) and seven blends (B{sub 0}, B{sub 5}, B{sub 1}5, B{sub 2}5, B{sub 5}0, B{sub 7}5 and B{sub 1}00). The results had evidenced that additioning 15% of biodiesel into diesel, the specific consumption was similar, and biodiesel of residual oil provided less consumption than biodiesel from hydrogenated fat. (author)

Deep desulfurization of middle distillates. Process adaptation to oil fractions' compositions

Energy Technology Data Exchange (ETDEWEB)

Pedernera, Esteban; Reimert, Rainer; Nguyen, Ngoc Luan; Van Buren, Vincent [Division of Fuel Technology, Universitat Karlsruhe TH, Engler-Bunte-Ring 1, 76131 Karlsruhe (Germany)

2003-04-30

The influence of oil fractions' compositions on the conversion of sulfurous components was investigated in a trickle-bed reactor in laboratory scale. A commercially available NiMo/{gamma}-Al{sub 2}O{sub 3} catalyst was used throughout the investigations. Experimental results including sulfur conversion of different oil fractions and residence time distributions under reacting conditions are presented. The hydrogen consumption is ascribed to the conversion of sulfur and of nitrogen, to the hydrogenation of aromatics and to hydrocracking based on a simulation applying ASPEN Plus. Various configurations of the desulfurization process are evaluated but no advantage is found by separate treatment of individual oil fractions. In addition, experiments were carried out to determine liquid distribution and wetting efficiency in a catalyst bed by using magnetic resonance imaging (MRI) technique.

Membrane distillation for milk concentration

NARCIS (Netherlands)

Moejes, S.N.; Romero Guzman, Maria; Hanemaaijer, J.H.; Barrera, K.H.; Feenstra, L.; Boxtel, van A.J.B.

2015-01-01

Membrane distillation is an emerging technology to concentrate liquid products while producing high quality water as permeate. Application for desalination has been studied extensively the past years, but membrane distillation has also potential to produce concentrated food products like

Refining shale-oil distillates

Energy Technology Data Exchange (ETDEWEB)

Altpeter, J

1952-03-17

A process is described for refining distillates from shale oil, brown coal, tar, and other tar products by extraction with selective solvents, such as lower alcohols, halogen-hydrins, dichlorodiethyl ether, liquid sulfur dioxide, and so forth, as well as treating with alkali solution, characterized in that the distillate is first treated with completely or almost completely recovered phenol or cresotate solution, the oil is separated from the phenolate with solvent, for example concentrated or adjusted to a determined water content of lower alcohol, furfural, halogen-hydrin, dichlorodiethyl ether, liquid sulfur dioxide, or the like, extracted, and the raffinate separated from the extract layer, if necessary after distillation or washing out of solvent, and freeing with alkali solution from residual phenol or creosol.

Comparison of procedures for reducing cross-contamination during steam distillations in nitrogen-15 tracer research

International Nuclear Information System (INIS)

Mulvaney, R.L.

1986-01-01

A study was conducted to compare the effectiveness of various procedures for reduction of cross-contamination errors when unenriched samples of (NH 4 ) 2 SO 4 containing 0.5 mg of N were steam-distilled in a glass distillation apparatus following samples enriched with 50 atom % 15 N. Twelve procedures were compared in this study, including most of those previously proposed in the literature. None of the procedures completely eliminated cross-contamination; however, some were considerably more effective than others. The results suggest that, when a glass distillation apparatus is used in 15 N-tracer research, the best way to reduce cross-contamination error is to distill two aliquots of each sample whenever possible, discarding the first distillate and retaining the second for isotope-ratio analysis. When this is not possible, it is recommended that 1 mL of 1M formic acid be distilled for 1 min and 25 mL of 16.4 M (95%) ethanol be distilled for 3 min between samples. This procedure can be made more effective by increasing the amount of formic acid used and extending distillation beyond 1 min

Physicochemical properties and analysis of Malaysian palm fatty acid distilled

Science.gov (United States)

Jumaah, Majd Ahmed; Yusoff, Mohamad Firdaus Mohamad; Salimon, Jumat

2018-04-01

Palm fatty acid distillate (PFAD) is cheap and valuable byproduct of edible oil processing industries. This study was carried out to determine the physicochemical properties of Malaysian palm fatty acid distilled (PFAD). The physicochemical properties showed that the free fatty acid (FFA %), acid value, iodine value, saponification value, unsaponifiable matter, hydroxyl value, specific gravity at 28°C, moisture content, viscosity at 40°C and colour at 28°C values were 87.04± 0.1 %, 190.6± 1 mg/g, 53.3±0.2 mg/g, 210.37±0.8 mg/g, 1.5±0.1%, 47±0.2 mg/g, 0.87 g/ml, 0.63 %, 30 cSt and yellowish respectively. Gas chromatography (GC) was used to determine the fatty acid (FA) composition in PFAD. The fatty acids were found to be comprised mostly with 48.9 % palmitic acid (C16:0), 37.4 % oleic acid (C18:1), 9.7 % linoleic acid (C18:2), 2.7 % stearic acid (C18:0) and 1.1 % myristic acid (C14:0). The analysis of high performance liquid chromatography (HPLC) has resulted with 99.2 % of FFA, while diacylglycerol and monoacylglycerol were 0.69 and 0.062 % respectively.

Investigation on the effect of heavy diesel fraction properties on product sulphur during ultra deep diesel hydrodesulphurization

Energy Technology Data Exchange (ETDEWEB)

Stratiev, D.; Tzingov, T. [Research and Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria); Galkin, V. [Future Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria)

2006-02-01

This work investigates the hydrotreatment of heavy diesel fractions in order to achieve product sulphurs of 50 and 10 ppm. The heavy diesel fractions were obtained in the Lukoil Neftochim Bulgaria (LNB) crude distillation and vacuum distillation units (SRGO1, SRGO2, AGO, LVGO ASTM D-86 95%vol. of 360, 392 395, and 377 C respectively) by distillation of crude oil type ''Ural'', containing some quantities of naphtha, atmospheric residue, vacuum gas oil and low sulphur crude oil, in the mild hydrocracking unit (MHC diesel 95%vol. of 389 C) and in the fluid catalytic cracking unit - heavy cycle oil (FCC HCO; 95%vol. of 360 C). The diesel fractions were hydrotreated in a trickle bed pilot plant at following conditions: reactor inlet temperature range of 300-380 C; liquid hourly space velocity (LHSV) range of 0.5-3.0 h{sup -1}, total reactor pressure range of 3.5- 7.0 MPa; treating gas/feedstock ratio of 250 Nm{sup 3}/m{sup 3}. It was found that in the investigated range of operating conditions the product sulphur depended linearly on the LHSV. As a measure of the diesel hydrodesulphurization (HDS) reactivity the LHSV at 360 C reactor inlet temperature was interpolated at a constant product sulphur level of 50 ppm and extrapolated at 10 ppm sulphur. It was found that the most refractory feedstock was the diesel mixture 80%SRGO1 / 20%FCCHCO (LHSV of 0.4 h{sup -1} for 50 ppm and 0.2 h{sup -1} for 10 ppm sulphur). The catalyst volume increase required to reduce the product sulphur from 50 to 10 ppm was found to be as high as twice for all diesel fractions except the MHC diesel. This material required five times the catalyst volume for the product sulphur reduction from 50 to 10 ppm. The total reactor pressure was found to have less impact on the product sulphur than the LHSV. Doubling the reactor pressure from 3.5 to 7.0 MPa by hydrotreatment of LVGO reduced the product sulphur as low as twice while the reduction of the LHSV from 1 to 0.5 h{sup -1} at a

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Trumble, M J

1925-06-29

Carbonaceous materials such as coal, oil shale, peat, or wood are destructively distilled while being subjected to the action of superheated steam and hydrogen, the latter being provided by dissociating a part of the superheated steam. The materials are charged into a retort heated by a burner and superheated steam and hydrogen are passed in by a pipe and nozzles. The distillates enter a dust extractor through openings and escape through openings shielded by cones into an outlet pipe leading to condensers. The dust which settles in the bottom of the apparatus is periodically removed.

Spectrophotometric method for quantitative measuring essential oil in aromatic water and distillate with rose smell

International Nuclear Information System (INIS)

Semenova, E; Moiseeva, I; Presnyakova, V; Goncharov, D; Goncharov, M; Presnyakova, E; Presnyakov, S; Kolesnikova, S

2017-01-01

In this connection, we improved the express methods of determining the mixture of volatile aromatic substances by the spectrophotometry of aromatic water and steam distillate of essential oil raw materials (traditional or biotechnological with rose smell). Direct spectrophotometry of distillation water is impossible because it is a colloid of liquid oil and law is not observed. Therefore, it is necessary to dissolve 1 ml of distillate in ethanol in the ratio 1:4, in this case we take real solution with no lipophilic fall-out on the walls of cuvette, also the light absorption law is observed. There are stable maximums in spectrums of studied oils. Optical density of these maximums is a result of summary absorption of terpenoid components (aromatic and monoterpene alcohols, its ethers). Optical density of tested and standard solutions is measured in appropriate wavelengths. Spectrophotometric method of determination of essential oil quantity in aromatic water with rose smell differs with high sensitivity (10 -5 -10 -6 gmol/l) and allows to determine oil concentration from 0,900 to 0,008 mg with an error less than 1%. At that, 1 ml is enough for analysis. It’s expedient to apply this method while operating with small quantity of water distillate in biochemical and biotechnological researches and also as express control for extraction and hydrodistillation of essential oil raw material (rose petals and flowers from different origin, eremothecium cultural liquid etc.). (paper)

Studies in Petroleum Composition the Distribution of Nitrogen Species, Metals and Coke Precursors During High Vacuum Distillation of Petroleum Étude de composition du pétrole Répartition des espèces azotées, des métaux et des précurseurs du coke pendant la distillation sous vide poussé du pétrole

Directory of Open Access Journals (Sweden)

Long R. B.

2006-11-01

Full Text Available Application of separation techniques to residua and other heavy feedstocks raises the issue of the most appropriate distillation cut-point for the maximum yield of useful (gas-oil type liquids. This publication addresses this specific issue and describes the influence of deepdistillation (to 1289°F+ on the composition and quality of the volatiles/nonvolatiles from a 950°F+ residuum. The techniques employed to estimate the composition/quality of the 950-1289°F and 1289°F+ fractions are deasphalting and clay-adsorption separation of each whole fraction. The data show that further distillation of the 950°F+ residuum can recover essentially all of the saturate content of the feed in the overhead product at 1289°F atmos. equiv. cut point. However, appreciable amounts of oxygen- and nitrogen-containing polar compounds are also taken overhead leading to a carbon residue value for the distillate of 8. 2 wt%. The metals and the coke precursors in the distillate lie mainly in the polar fraction along with the nitrogen compounds. However, at these high molecular weights the distillate also shows coke precursors in the saturate fraction and more extensively in the aromatic fraction. Distillation is an impurity (carbon precursors, heteroatoms, metals concentrating process. As the cut-point increases, the impurity content of the distillate increases but to a lesser extent than that of the corresponding residuum. L'application des techniques de séparation aux résidus et autres matières lourdes conduit à s'interroger sur le point de coupe de distillation adéquat qui va permettre d'obtenir le rendement maximum en liquides utiles (type gazole. Il faut reconnaître que la distillation est un processus de concentration des impuretés (produits de tête, hétéroatomes, métaux. Lorsque le point de coupe s'élève, le contenu en impuretés du distillat augmente, mais il augmente moins que celui du résidu correspondant. La présente publication �

Method of distilling organic materials

Energy Technology Data Exchange (ETDEWEB)

Gustafsson, E G.T.

1921-11-11

In the distillation of organic materials, by means of coursing heated gases through the distillation chamber, that can be heated by other means also, a method is given by which the hot gases coming from the distillation chamber are cooled in one or more heat-absorbent devices (for example, in spray coolers, condensers and/or water). The greater part of the products or constituents condensable at ordinary temperature are separated from the vapors and gases, and thereafter the gases should be passed through the distillation chamber after the necessary additional heating in special heaters, as one or more heat producers, suitably of the same construction as the heat absorbers, for heating and saturation with steam by means of warm condensate and/or water obtained fully or partly from the heat absorbers, possibly after separation of tar or oil from them. The patent has 11 other claims.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Urquhart, D

1882-08-19

Manufacture of ammonia and purification of shale oils are described. In the distillation of shales, increase of ammonia is obtained and the oils are less contaminated by sulfur, by mixing a small proportion, about two to three percent, of lime or slaked line with the shale. The same process is used with other carbonaceous substances containing nitrogen, such as peat, coal, or the like; but a smaller proportion of lime is used than in the former case, and the lime is slaked with caustic soda solution. When slack or waste coal or other carbonaceous substances are distilled by heated air or gases arising from imperfect combustion, as in furnaces on the gas producer principle, slaked lime is added to the slack or other material.

Distilling oils

Energy Technology Data Exchange (ETDEWEB)

Leffer, L G

1912-01-29

In a process for converting heavy hydrocarbons, such as petroleum or shale oil, into light hydrocarbons by distilling under the pressure of an inert gas, the operation is conducted at a temperature not exceeding 410/sup 0/C and under an accurately regulated pressure, the gas being circulated through the still and the condenser by means of a pump. The oil in the still may be agitated by stirring vanes or by blowing the gas through it. Hydrogen, nitrogen, carbon dioxide, methane, or gases generated in the distillation may be used as pressure media; the gas is heated before its admission to the still. A pressure of from 11 to 12 atmospheres is used in treating gas oil. Specification 10,277/89 is referred to.

Tritium isotope separation by water distillation column packed with silica-gel beads

International Nuclear Information System (INIS)

Fukada, Satoshi

2004-01-01

Tritium enrichment or depletion by water distillation was investigated using a glass column of 32cm in height packed with silica-gel beads of 3.4mm in average diameter. The total separation factor of the silica-gel distillation column, α H-T , was compared with those of an open column distillation tower and of a column packed with stainless-steel Dixon rings. Depletion of the tritium activity in the distillate was enhanced by isotopic exchange with water absorbed on silica-gel beads that have a higher affinity for HTO than for H 2 O. The value of α H-T -1 of the silica-gel distillation column was about four times larger than that of a column without any packing and about two times larger than that of the Dixon-ring column. The improvement of α H-T by the silica-gel adsorbent indicated that the height of the distillation-adsorption column becomes shorter than that of the height of conventional distillation columns. (author)

A totally heat-integrated distillation column (THIDiC) - the effect of feed pre-heating by distillate

Energy Technology Data Exchange (ETDEWEB)

Huang Kejin [School of Information Science and Technology, Beijing University of Chemical Technology, Beijing 100029 (China)], E-mail: huangkj@mail.buct.edu.cn; Shan Lan; Zhu Qunxiong [School of Information Science and Technology, Beijing University of Chemical Technology, Beijing 100029 (China); Qian Jixin [School of Information Science and Technology, Zhejiang University, Zhejiang 300027 (China)

2008-06-15

An ideal heat-integrated distillation column (ideal HIDiC) is characterized by external zero-reflux and zero-reboil ratio operation. Since the distillate is a high-pressure vapor phase flow, it can be used to pre-heat the feed to be separated, thereby giving rise to a totally heat-integrated distillation column (THIDiC). Although the THIDiC is more thermodynamically efficient than the ideal HIDiC, it is found that the heat integration between the distillate and feed turns it into an open-loop integrating process and poses additional difficulties to process operation. Therefore, a careful decision must be made on the selection between the ideal HIDiC and the THIDiC during process development. In this paper, separation of a binary equimolar mixture of benzene and toluene is selected as an illustrative example. Both process design and operability analysis are conducted, with special emphasis focused on the characteristics of feed pre-heating with distillate. The results obtained show deep insight into the design and operation of the THIDiC.

A totally heat-integrated distillation column (THIDiC) - the effect of feed pre-heating by distillate

International Nuclear Information System (INIS)

Huang Kejin; Shan Lan; Zhu Qunxiong; Qian Jixin

2008-01-01

An ideal heat-integrated distillation column (ideal HIDiC) is characterized by external zero-reflux and zero-reboil ratio operation. Since the distillate is a high-pressure vapor phase flow, it can be used to pre-heat the feed to be separated, thereby giving rise to a totally heat-integrated distillation column (THIDiC). Although the THIDiC is more thermodynamically efficient than the ideal HIDiC, it is found that the heat integration between the distillate and feed turns it into an open-loop integrating process and poses additional difficulties to process operation. Therefore, a careful decision must be made on the selection between the ideal HIDiC and the THIDiC during process development. In this paper, separation of a binary equimolar mixture of benzene and toluene is selected as an illustrative example. Both process design and operability analysis are conducted, with special emphasis focused on the characteristics of feed pre-heating with distillate. The results obtained show deep insight into the design and operation of the THIDiC

Three-phase fluidized distillation

International Nuclear Information System (INIS)

Ravagnani, T.M.K.; Pereira, J.A.F.R.

2001-01-01

Separation efficiency in distillation operations can be improved by modifying the characteristics of the dispersions formed on the trays. The present work reports on the hydrodynamic and mass transfer characteristics of liquid-solid-vapour dispersions formed on sieve trays without downcomers of a distillation column operating under total reflux conditions. Murphree efficiency and the operating limits of distillation using the ethanol-n-butanol system are analyzed for a large range of vapour velocities and liquid mixture compositions, utilising wettable PVC particles and non-wettable silicone, PE, and Teflon((R)) particles. It was verified that wettable particles show a drastic reduction in the upper operating limit of vapour velocity, but this does not occur for non-wettable particles. Tray efficiency can be increased when non-wettable particles are used, mainly for high vapour velocity operations. (author)

Chromatographic finger print analysis of anti-inflammatory active extract fractions of aerial parts of Tribulus terrestris by HPTLC technique

Science.gov (United States)

Mohammed, Mona Salih; Alajmi, Mohamed Fahad; Alam, Perwez; Khalid, Hassan Subki; Mahmoud, Abelkhalig Muddathir; Ahmed, Wadah Jamal

2014-01-01

Objective To develop HPTLC fingerprint profile of anti-inflammatory active extract fractions of Tribulus terrestris (family Zygophyllaceae). Methods The anti-inflammatory activity was tested for the methanol and its fractions (chloroform, ethyl acetate, n-butanol and aqueous) and chloroform extract of Tribulus terrestris (aerial parts) by injecting different groups of rats (6 each) with carrageenan in hind paw and measuring the edema volume before and 1, 2 and 3 h after carrageenan injection. Control group received saline i.p. The extracts treatment was injected i.p. in doses of 200 mg/kg 1 h before carrageenan administration. Indomethacin (30 mg/kg) was used as standard. HPTLC studies were carried out using CAMAG HPTLC system equipped with Linomat IV applicator, TLC scanner 3, Reprostar 3, CAMAG ADC 2 and WIN CATS-4 software for the active fractions of chloroform fraction of methanol extract. Results The methanol extract showed good antiedematous effect with percentage of inhibition more than 72%, indicating its ability to inhibit the inflammatory mediators. The methanol extract was re-dissolved in 100 mL of distilled water and fractionated with chloroform, ethyl acetate and n-butanol. The four fractions (chloroform, ethyl acetate, n-butanol and aqueous) were subjected to anti-inflammatory activity. Chloroform fraction showed good anti-inflammatory activity at dose of 200 mg/kg. Chloroform fraction was then subjected to normal phase silica gel column chromatography and eluted with petroleum ether-chloroform, chloroform-ethyl acetate mixtures of increasing polarity which produced 15 fractions (F1-F15). Only fractions F1, F2, F4, F5, F7, F9, F11 and F14 were found to be active, hence these were analyzed with HPTLC to develop their finger print profile. These fractions showed different spots with different Rf values. Conclusions The different chloroform fractions F1, F2, F4, F5, F7, F9, F11 and F14 revealed 4, 7, 7, 8, 9, 7, 7 and 6 major spots, respectively. The

Irreversibility of entanglement distillation for a class of symmetric states

International Nuclear Information System (INIS)

Vollbrecht, Karl Gerd H.; Wolf, Michael M.; Werner, Reinhard F.

2004-01-01

We investigate the irreversibility of entanglement distillation for a symmetric (d+1)-parameter family of mixed bipartite quantum states acting on Hilbert spaces of arbitrary dimension dxd. We prove that in this family the entanglement cost is generically strictly larger than the distillable entanglement, so that the set of states for which the distillation process is asymptotically reversible is of measure zero. This remains true even if the distillation process is catalytically assisted by pure-state entanglement and every operation is allowed, which preserves the positivity of the partial transpose. It is shown that reversibility occurs only in cases where the state is a tagged mixture. The reversible cases are shown to be completely characterized by minimal uncertainty vectors for entropic uncertainty relations

7 CFR 160.8 - Steam distilled wood turpentine.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Steam distilled wood turpentine. 160.8 Section 160.8... STANDARDS FOR NAVAL STORES General § 160.8 Steam distilled wood turpentine. The designation “steam distilled wood turpentine” shall refer to the kind of spirits of turpentine obtained by steam distillation from...

Ekstraksi Minyak Atsiri Dari Akar Wangi Menggunakan Metode Steam - Hydro distillation dan Hydro distilation dengan Pemanas Microwave

Directory of Open Access Journals (Sweden)

Maulana M Al Hanief

2013-09-01

Full Text Available Penelitian ini bertujuan untuk memperoleh minyak atsiri dari akar wangi dengan modifikasi metode steam-hydro distillation dan hydro distillation yaitu menggunakan pemanasan microwave kemudian membandingkan hasilnya dengan penelitian sebelumnya. Modifikasi ini diharapkan lebih efisien dalam masalah lama penyulingan dan kualitas serta kuantitas rendemen minyak yang lebih baik dan banyak. Penelitian ini menggunakan dua metode yaitu steam-hydro distillation dan hydro distillation dengan pemanfaatan gelombang mikro. Bahan baku yang digunakan dalam penelitian adalah akar wangi jenis pulus wangi yang tumbuh di Kabupaten Garut, Jawa Barat. Variabel yang digunakan adalah bahan baku yang dicacah dan bahan baku utuh dengan variasi massa bahan 50 gr, 60, gr, 70 gr, 80 gr, dan 90 gr dengan pelarut air sebanyak 450 ml dalam labau distiller berukuran 1000 ml. Lama penyulingan adalah lima jam dengan pengamatan tiap 30 menit serta daya yang digunakan adalah 400 Watt. Analisa terhadap hasil minyak atsiri yang diperoleh antara lain analisa GC-MS, spesific gravity, indeks bias, dan bilangan asam. Hasil dari penelitian ini dibandingkan dengan hasil penelitian terdahulu yang tidak memanfaatkan gelombang mikro. Dari hasil penelitian diperoleh % rendemen kumulatif, sifat fisik, sifat kimia, dan kandungan komponen minyak dari metode steam-hydro distillation lebih baik dibandingkan metode hydro distillation ditandai dengan kuantitas dan kualitas yang sesuai dengan SNI.  Sementara itu jika dibandingkan dengan metode terdahulu dapat disimpulkan bahwa penggunaan gelombang mikro lebih efisien dalam waktu dan kuantitas serta kualitas minyak yang lebih baik dibandingkan tanpa penggunaan gelombang mikro

40 CFR Appendix A to Part 419 - Processes Included in the Determination of BAT Effluent Limitations for Total Chromium...

Science.gov (United States)

2010-07-01

..., and Phenolic Compounds (4AAP) Crude Processes 1. Atmospheric Crude Distillation 2. Crude Desalting 3. Vacuum Crude Distillation Cracking and Coking Processes 4. Visbreaking 5. Thermal Cracking 6. Fluid... Oil Manufacture 23. Propane Dewaxing, Propane Deasphalting, Propane Fractioning, Propane Deresining 24...

Low temperature distillation of coal, shale, etc

Energy Technology Data Exchange (ETDEWEB)

1938-08-12

A process is disclosed for the low temperature distillation of solid carbonaceous fuels, such as coal, lignite, shale or the like, which comprises feeding or supplying the comminuted fuel in the form of a layer of shallow depth to drying and distilling zones in succession moving the fuel forward through the zones, submitting it to progressively increasing nonuniform heating therein by combustion gases supplied to the distillation zone and traveling thence to the drying zone, the gases heating the distillation zone indirectly and the drying zone both indirectly and then directly such that the fuel retains its solid discrete form during substantially the whole of its travel through the drying and distillation zones, subjecting the fuel for a portion of its travel to a zigzag ploughing and propelling movement on a heated sole, and increasing the heating so as to cause fusion of the fuel immediately prior to its discharge from the distillation zone.

Method of producing pitch (distillation residue)

Energy Technology Data Exchange (ETDEWEB)

Stepanenko, M.A.; Belkina, T.V.; Krysin, V.P.

1979-08-15

A method is proposed for producing pitch by mixing hard coal pitch with anthracene fraction and thermal treatment of the mixture. The method is distinguished in that in order to increase the quality of the pitch, the anthracene fraction is subjected to thermal treatment at 250-300/sup 0/ for 10-13 hours in the presence of air. This duration of heat treatment allows one to build up in the anthracene fraction up to 20-24% of material which is not soluble and toluene, without the formation of products which are not soluble in quinoline. The fraction prepared in this manner is inserted into the initial pitch in the ratio 1:2 up to 1:9, the mixture is subject to heat treatment at temperature 360-380/sup 0/ and air consumption 7-91/kgX hours until the production of pitch with softening temperature of 85-90/sup 0/. As the initial raw material we used pitch with softening temperature of 60/sup 0/, content of substances which are not soluble in quinoline, 2.0% which are not soluble and toluene 20.6% and coking residue of 49.2%. Example. 80 grams of anthracene fraction is added to 320 grams of pitch. The anthracene fraction is subjected previously to heat treatment at 300/sup 0/ for 13 hours in the presence of air, supplied in the amount of 9 liters per hour. As a result of the heat treatment of the content of materials which are not soluble in toluence in the anthracene fraction is 24.0%, in quinoline it is 0.1%. The ratio of a pitch and thermally treated anthracene fraction in the mixture was 4:l. The produced mixture was subjected to heat treatment at 360/sup 0/ for 1.5 hours with air supply in the amount of 7 liters/ kilograms/hours. Pitch is produced with the following characteristics: softening temperature 88/sup 0/, content of substances which are not soluble in toluene 32.5%, in quinilone, 6.0%, coking residue, 56.7%. The invention can be used in the chemical coking and petrochemical industry.

27 CFR 26.135 - Containers of distilled spirits to bear closures.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Containers of distilled spirits to bear closures. 26.135 Section 26.135 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO... to bear closures. Containers of 1 gallon (3.785 liters) or less of distilled spirits, upon which all...

Quantum Entanglement: Separability, Measure, Fidelity of Teleportation, and Distillation

Directory of Open Access Journals (Sweden)

Ming Li

2010-01-01

Full Text Available Quantum entanglement plays crucial roles in quantum information processing. Quantum entangled states have become the key ingredient in the rapidly expanding field of quantum information science. Although the nonclassical nature of entanglement has been recognized for many years, considerable efforts have been taken to understand and characterize its properties recently. In this review, we introduce some recent results in the theory of quantum entanglement. In particular separability criteria based on the Bloch representation, covariance matrix, normal form and entanglement witness, lower bounds, subadditivity property of concurrence and tangle, fully entangled fraction related to the optimal fidelity of quantum teleportation, and entanglement distillation will be discussed in detail.

Dynamic effects of diabatization in distillation columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2013-01-01

The dynamic effects of diabatization in distillation columns are investigated in simulation emphasizing the heat-integrated distillation column (HIDiC). A generic, dynamic, first-principle model has been formulated, which is flexible enough to describe various diabatic distillation configurations....... Dynamic Relative Gain Array and Singular Value Analysis have been applied in a comparative study of a conventional distillation column and a HIDiC. The study showed increased input-output coupling due to diabatization. Feasible SISO control structures for the HIDiC were also found and control...

Dynamic Effects of Diabatization in Distillation Columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2012-01-01

The dynamic eects of diabatization in distillation columns are investigated in simulation with primary focus on the heat-integrated distillation column (HIDiC). A generic, dynamic, rst-principle model has been formulated, which is exible to describe various diabatic distillation congurations....... Dynamic Relative Gain Array and Singular Value Analysis have been applied in a comparative study of a conventional distillation column and a HIDiC. The study showed increased input-output coupling due to diabatization. Feasible SISO control structures for the HIDiC were also found. Control...

DESIGN AND CONSTRUCTION OF A REFLUX COLUMN DISTILLATION UNIT FOR BIO-ETHANOL PRODUCTION FROM SUGARCANE SUBSTRATE

Directory of Open Access Journals (Sweden)

J. O. Olaoye

2011-06-01

Full Text Available A bio-ethanol distilling tank was designed and constructed to distil ethanol from sugarcane substrate. The machine has a capacity to process 200 litres of substrate at full load of the boiler. The distiller has mlntemalReflux Still Condenser (IRSC that controls the internal re-distillation process and the separation of the final output. The column diameter was 40 mm. An anaerobic fermentation of substrate was adopted before distillation could be carried out. The fermented substrate was adjusted to an optimum pH level value of 4-5 by addition of 0.1 M HjSQ, and the optimum temperature was within the temperature range of 29-38°C. A charcoal pot was used as heat source. The results of the machine evaluation showed that optimum yield occurred at 0.0325 ratio of substrate to ethanol yield. An average distilled product of 2.1 litres was obtained at highest ratio of substrate to ethanol yield of 0.033 when the distillation time was 45 minutes. The total distilled products after 1XA hours of distillation was estimated at 4.25 litres. It was observed that the fermentation and distillation processes were done in situ, and could definitely affect clear separation of the fermentable portion of the fermented sugar solution.

Submerged membrane distillation for seawater desalination

KAUST Repository

Francis, Lijo; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Amy, Gary L.

2014-01-01

A submerged membrane distillation (SMD) process for fresh water production from Red Sea water using commercially available hollow fiber membranes has been successfully employed and compared with the conventional direct contact membrane distillation (DCMD) process. The hollow fiber membranes have been characterized for its morphology using field effect scanning electron microscope. In SMD process, a bunch of hollow fiber membranes are glued together at both ends to get a simplified open membrane module assembly submerged into the coolant tank equipped with a mechanical stirrer. Hot feed stream is allowed to pass through the lumen side of the membrane using a feed pump. Continuous stirring at the coolant side will reduce the temperature and concentration polarization. During the conventional DCMD process, using feed-coolant streams with co-current and counter-current flows has been tested and the results are compared in this study. In SMD process, a water vapor flux of 10.2 kg m-2 h-1 is achieved when using a feed inlet temperature of 80°C and coolant temperature of 20°C. Under the same conditions, during conventional DCMD process, a water vapor flux of 11.6 and 10.1 kg m-2 h-1 were observed during counter-current and co-current flow streams, respectively. Results show that the water production in the SMD process is comparable with the conventional DCMD process, while the feed-coolant flow streams are in the co-current direction. During conventional DCMD operation, a 15% increase in the water production is observed when feed-coolant streams are in the counter-current direction compared to the co-current direction. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

Submerged membrane distillation for seawater desalination

KAUST Repository

Francis, Lijo

2014-08-11

A submerged membrane distillation (SMD) process for fresh water production from Red Sea water using commercially available hollow fiber membranes has been successfully employed and compared with the conventional direct contact membrane distillation (DCMD) process. The hollow fiber membranes have been characterized for its morphology using field effect scanning electron microscope. In SMD process, a bunch of hollow fiber membranes are glued together at both ends to get a simplified open membrane module assembly submerged into the coolant tank equipped with a mechanical stirrer. Hot feed stream is allowed to pass through the lumen side of the membrane using a feed pump. Continuous stirring at the coolant side will reduce the temperature and concentration polarization. During the conventional DCMD process, using feed-coolant streams with co-current and counter-current flows has been tested and the results are compared in this study. In SMD process, a water vapor flux of 10.2 kg m-2 h-1 is achieved when using a feed inlet temperature of 80°C and coolant temperature of 20°C. Under the same conditions, during conventional DCMD process, a water vapor flux of 11.6 and 10.1 kg m-2 h-1 were observed during counter-current and co-current flow streams, respectively. Results show that the water production in the SMD process is comparable with the conventional DCMD process, while the feed-coolant flow streams are in the co-current direction. During conventional DCMD operation, a 15% increase in the water production is observed when feed-coolant streams are in the counter-current direction compared to the co-current direction. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

PERFORMANCE INDICES TO DESIGN A MULTICOMPONENT BATCH DISTILLATION COLUMN USING A SHORTCUT METHOD

Directory of Open Access Journals (Sweden)

A. Narvaes-Garcia

2015-06-01

Full Text Available AbstractIn this paper, three quality or performance indices (Luyben's capacity factor, total annual costs, and annual profit were applied for the design of a batch distillation column working at variable reflux. This work used the Fenske-Underwood-Gilliland short-cut method to solve a problem of four components (benzene, toluene, ethyl-benzene, and ortho-xylene that needed to be separated and purified to a mole fraction of 0.97 or better. The performance of the system was evaluated using distillation columns with 10, 20, 30, 40 and 50 theoretical stages with a boil-up vapor flow set at 100 kmol/h. It was found that the annual profit was the best quality index, while the best case for variable reflux was the column with 50 stages. It was confirmed that the best case always required a reflux ratio close to the minimum.

Destructive distillation under pressure

Energy Technology Data Exchange (ETDEWEB)

1932-09-08

A process of destructive distillation of distillable carbonaceous material under pressure is described, consisting of regulating the temperature by introducing the carbonaceous materials to a point where the reaction of hydrogenation has begun but has not stopped, by placing it in indirect heat-exchange with a cooling agent at a critical temperature below the reaction temperature, the agent being under pressure and introduced in the liquid state. Water is used as the cooling agent.

Secret key distillation from shielded two-qubit states

International Nuclear Information System (INIS)

Bae, Joonwoo

2010-01-01

The quantum states corresponding to a secret key are characterized using the so-called private states, where the key part consisting of a secret key is shielded by the additional systems. Based on the construction, it was shown that a secret key can be distilled from bound entangled states. In this work, I consider the shielded two-qubit states in a key-distillation scenario and derive the conditions under which a secret key can be distilled using the recurrence protocol or the two-way classical distillation, advantage distillation together with one-way postprocessing. From the security conditions, it is shown that a secret key can be distilled from bound entangled states in a much wider range. In addition, I consider the case that in which white noise is added to quantum states and show that the classical distillation protocol still works despite a certain amount of noise although the recurrence protocol does not.

Ethanol dehydration via azeotropic distillation with gasoline fractions as entrainers: A pilot-scale study of the manufacture of an ethanol–hydrocarbon fuel blend

OpenAIRE

Gomis Yagües, Vicente; Pedraza Berenguer, Ricardo; Saquete Ferrándiz, María Dolores; Font, Alicia; Garcia-Cano, Jorge

2015-01-01

We establish experimentally and through simulations the economic and technical viability of dehydrating ethanol by means of azeotropic distillation, using a hydrocarbon as entrainer. The purpose of this is to manufacture a ready-to-use ethanol–hydrocarbon fuel blend. In order to demonstrate the feasibility of this proposition, we have tested an azeotropic water–ethanol feed mixture, using a hydrocarbon as entrainer, in a semi pilot-plant scale distillation column. Four different hydrocarbons ...

One Adaptive Synchronization Approach for Fractional-Order Chaotic System with Fractional-Order 1 < q < 2

Science.gov (United States)

Zhou, Ping; Bai, Rongji

2014-01-01

Based on a new stability result of equilibrium point in nonlinear fractional-order systems for fractional-order lying in 1 < q < 2, one adaptive synchronization approach is established. The adaptive synchronization for the fractional-order Lorenz chaotic system with fractional-order 1 < q < 2 is considered. Numerical simulations show the validity and feasibility of the proposed scheme. PMID:25247207

Performance of different hollow fiber membranes for seawater desalination using membrane distillation

KAUST Repository

Francis, Lijo; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Amy, Gary L.

2014-01-01

Membrane distillation requires a highly porous hydrophobic membrane with low surface energy. In this paper, we compare the direct contact membrane distillation (DCMD) performances of four different types of in-house fabricated hollow fiber membranes and two different commercially available hollow fiber membranes. Hollow fiber membranes are fabricated using wet-jet phase inversion technique and the polymeric matrices used for the fabrication are polyvinylidine fluoride (PVDF) and polyvinyl chloride (PVC). Commercial hollow fiber membrane materials are made of polytetrafluoroethylene (PTFE) and polypropylene (PP). PVDF hollow fibers showed a superior performance among all the hollow fibers tested in the DCMD process and gave a water vapor flux of 31 kg m-2h-1 at a feed and coolant inlet temperatures of 80 and 20°C, respectively. Under the same conditions, the water vapor flux observed for PP, PTFE, and PVC hollow fiber membranes are 13, 11, and 6 kg m-2h-1, respectively, with 99.99% salt rejection observed for all membranes used.

Performance of different hollow fiber membranes for seawater desalination using membrane distillation

KAUST Repository

Francis, Lijo

2014-08-11

Membrane distillation requires a highly porous hydrophobic membrane with low surface energy. In this paper, we compare the direct contact membrane distillation (DCMD) performances of four different types of in-house fabricated hollow fiber membranes and two different commercially available hollow fiber membranes. Hollow fiber membranes are fabricated using wet-jet phase inversion technique and the polymeric matrices used for the fabrication are polyvinylidine fluoride (PVDF) and polyvinyl chloride (PVC). Commercial hollow fiber membrane materials are made of polytetrafluoroethylene (PTFE) and polypropylene (PP). PVDF hollow fibers showed a superior performance among all the hollow fibers tested in the DCMD process and gave a water vapor flux of 31 kg m-2h-1 at a feed and coolant inlet temperatures of 80 and 20°C, respectively. Under the same conditions, the water vapor flux observed for PP, PTFE, and PVC hollow fiber membranes are 13, 11, and 6 kg m-2h-1, respectively, with 99.99% salt rejection observed for all membranes used.

Effect of hydroprocessing severity on characteristics of jet fuel from OSCO 2 and Paraho distillates

Science.gov (United States)

Prok, G. M.; Flores, F. J.; Seng, G. T.

1981-01-01

Jet A boiling range fuels and broad-property research fuels were produced by hydroprocessing shale oil distillates, and their properties were measured to characterize the fuels. The distillates were the fraction of whole shale oil boiling below 343 C from TOSCO 2 and Paraho syncrudes. The TOSCO 2 was hydroprocessed at medium severity, and the Paraho was hydroprocessed at high, medium, and low severities. Fuels meeting Jet A requirements except for the freezing point were produced from the medium severity TOSCO 2 and the high severity Paraho. Target properties of a broad property research fuel were met by the medium severity TOSCO 2 and the high severity Paraho except for the freezing point and a high hydrogen content. Medium and low severity Paraho jet fuels did not meet thermal stability and freezing point requirements.

Synthesis of Faujasite from Fly Ash and its Applications for Hydrocracking of Petroleum Distillates

Directory of Open Access Journals (Sweden)

Sutarno Sutarno

2007-10-01

Full Text Available The synthesis of faujasite from fly ash and its application for hydrocracking catalyst of heavy petroleum distillates have been performed. Faujasite was synthesized from fly ash by hydrothermal reaction in alkaline solution via combination of reflux pretreatment of fly ash with HCl and fusion with NaOH. The preparation of nickel containing catalysts by ion exchange method under similar initial concentration of nickel resulted higher amount of nickel loaded on faujasite than those on zeolite Y, however, the structural damage of faujasite was higher than those of zeolite Y. In the hydrocracking of heavy petroleum distillates over Ni-faujasite and Ni-zeolite Y catalysts, the conversion of heavy gas oil fraction was the most pronounced. The selectivity toward hydrocarbons in the range of gasoline and kerosene obtained over Ni-faujasite catalyst was lower compared to those of Ni-zeolite Y reference catalyst. © 2007 BCREC UNDIP. All rights reserved.[Presented at Symposium and Congress of MKICS 2007, 18-19 April 2007, Semarang, Indonesia][How to Cite: S. Sutarno, Y. Arryanto. (2007. Synthesis of Faujasite from Fly Ash and its Applications for Hydrocracking of Petroleum Distillates. Bulletin of Chemical Reaction Engineering and Catalysis, 2 (2-3: 45-51.  doi:10.9767/bcrec.2.2-3.9.45-51][How to Link/DOI: http://dx.doi.org/10.9767/bcrec.2.2-3.9.45-51 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/9][Cited by: Scopus 1 | ScienceAsia |

Vapor pressure isotope effect in 13CClF3/12CClF3 by cryogenic distillation kinetics

International Nuclear Information System (INIS)

Wieck, H.J.; Ishida, T.

1975-08-01

The vapor pressure of 13 CClF 3 relative to the vapor pressure of 12 CClF 3 was measured as a function of temperature between 169 0 and 206 0 K by using a modified Bigeleisen distillation column. The transient build-up of the isotopic concentration gradient along the length of the packed column during the start-up period was monitored by taking samples from the condenser section as a function of time. The gaseous samples were completely oxidized to carbon dioxide in the presence of a platinum catalyst and a large excess of oxygen at temperatures between 1050 and 1100 0 C. The combustion products were purified by means of gas chromatography, and the purified carbon dioxide samples were analyzed in a Nier-type isotope-ratio mass spectrometer. The data of each distillation run were reduced in the light of Cohen's theory of the kinetics of square cascade of close-separation stages. The vapor pressure isotope effect for the carbon substitution in CClF 3 at temperatures between 169 0 and 206 0 K was found to be an inverse effect and to be rather insensitive to changes in temperature. The relative vapor pressure may be expressed 1n(P'/P) = [(1.5 +- 14.1)/T 2 ] - [(0.159 +- 0.076)/T], or 1n(P'/P) = [(0.173 +- 0.098)/T] - [(0.11 +- 0.53) x 10 -3 ], where P' and P are the vapor pressures of 12 CClF 3 and 13 CClF 3 , respectively. To the first-order, the presence of chlorine isotopes would not affect the fractionation of carbon isotopes by the distillation of CClF 3

Phytochemical composition, cytotoxicity and in vitro antiplasmodial activity of fractions from Alafia barteri olive (Hook F. Icon-Apocynaceae

Directory of Open Access Journals (Sweden)

A.A. Lasisi

2016-01-01

Full Text Available The ethanolic extract of Alafia barteri (Hook F. Icon was dissolved in distilled water and successively partitioned in n-hexane, chloroform, ethyl acetate and n-butanol. The fractions were evaluated for phytochemical composition, lethality against brine shrimp larvae and in vitro antiplasmodial activity against Plasmodium falciparum strain. The obtained results revealed that the roots and leaf extracts of A. barteri exhibited broad spectrum of antiplasmodial activity (IC50 1.5 ± 0.7–6.2 ± 0.80 μg/mL. The aqueous leaf fractions displayed the most potent antiplasmodial activity with an IC50 value of 1.5 ± 0.7 μg/mL, which is comparable to reference antimalarial drug (IC50 value of 1.3 ± 0.2 μg/mL. The leaf fractions displayed higher activity than the root extracts. The highest minimum lethal concentration (105.2 ± 0.8 ppm was exhibited by the aqueous leaf extract followed closely by the root extract (120.2 ± 1.1 ppm. The leaf extracts contained higher polyphenols (45.3 ± 0.85 mgGAE/g and flavonoids (18.10 ± 0.2 mgCTE/g than the root extracts. The n-hexane and EtOAc extracts/fractions displayed lower activity on brine shrimp larvae.

27 CFR 1.62 - Use of distilled spirits or wine for experimental purposes and in manufacture of nonbeverage...

Science.gov (United States)

2010-04-01

... or wine for experimental purposes and in manufacture of nonbeverage products. 1.62 Section 1.62... experimental purposes and in manufacture of nonbeverage products. The use of distilled spirits or wine for experimental purposes and in the manufacture of (a) medicinal, pharmaceutical, or antiseptic products...

One Adaptive Synchronization Approach for Fractional-Order Chaotic System with Fractional-Order 1

Directory of Open Access Journals (Sweden)

Ping Zhou

2014-01-01

Full Text Available Based on a new stability result of equilibrium point in nonlinear fractional-order systems for fractional-order lying in 1fractional-order Lorenz chaotic system with fractional-order 1

Optimization of Palmitic Acid Composition in Crude Oleic Acid to Provide Specifications of Titer and Cloud Point of Distillate Oleic Acid using a Flash Distiller

OpenAIRE

Muhammad Yusuf Ritonga

2010-01-01

Titer and cloud point Distilled Oleic Acid’s higher than standard on feed composition palmitic acid (C15H31COOH) or C16 11.2 %. Feed composition C16, top temperature precut and bottom main distiller column were optimized to produce DOA. A factorial design 3 independent variables 3 X 2 X 3, twice repeating’s applied to observe effects of feed composition C16 to quality parameters. On the optimum C16 feed composition at 5.20 % was produced DOA with titer 6.8 oC, cloud point 5.0 oC (inside it...

Distillation of shale in situ

Energy Technology Data Exchange (ETDEWEB)

de Ganahl, C F

1922-07-04

To distill buried shale or other carbon containing compounds in situ, a portion of the shale bed is rendered permeable to gases, and the temperature is raised to the point of distillation. An area in a shale bed is shattered by explosives, so that it is in a relatively finely divided form, and the tunnel is then blocked by a wall, and fuel and air are admitted through pipes until the temperature of the shale is raised to such a point that a portion of the released hydrocarbons will burn. When distillation of the shattered area takes place and the lighter products pass upwardly through uptakes to condensers and scrubbers, liquid oil passes to a tank and gas to a gasometer while heavy unvaporized products in the distillation zone collect in a drain, flow into a sump, and are drawn off through a pipe to a storage tank. In two modifications, methods of working are set out in cases where the shale lies beneath a substantially level surface.

EASTERN DODDER (CUSCUTA MONOGYNA VAHL.) SEED GERMINATION AFFECTED BY SOME HERBACEOUS DISTILLATES.

Science.gov (United States)

Movassaghi, M; Hassannejad, S

2015-01-01

Eastern dodder (Cuscuta monogyna Vahl.) is one of the noxious parasitic weeds that infected many ornamental trees in green spaces and gardens. Our purpose is to find natural inhibitors for prevention of its seed germination. In order to reach this aim, laboratory studies were conducted by using of herbaceous distillates of Dracocephalum moldavica, Nasturtium officinalis, Malva neglecta, Mentha piperita, Mentha pulegium, Rosa damascene, Ziziphora tenuior, and Urtica dioica on seed germination of C. monogyna. Z. tenuior distillate stimulated C. monogyna seed germination, whereas others reduced this parasitic weed's seed germination. D. moldavica caused maximum inhibition on weed seed germination. Seedling growth of C. monogyna was more affected than its seed germination. All of these herbaceous distillates reduced C. monogyna seedling length so that the latter decreased from 28.2 mm in distilled water to 4.5, 3.97, 3.85, 3.67, 3.1, 2.87, 2.57, 1.9, and 1.17 in M. pulegium, M. piperita, F. officinalis, Z. tenuior, N. officinalis, M. neglecta, R. damascene, U. dioica and D. moldavica, respectively. By using these medicinal plants distillates instead of herbicides, the parasitic weed seedling length and host plant infection will reduce.

Operation and Design of Diabatic Distillation Processes

DEFF Research Database (Denmark)

Bisgaard, Thomas

Diabatic operation of a distillation column implies that heat is exchanged in one or more stages in the column. The most common way of realising diabatic operation is by internal heat integration resulting in a heat-integrated distillation column (HIDiC). When operating the rectifying section...... at a higher pressure, a driving forcefor transferring heat from the rectifying section to the stripping section is achieved. As a result, the condenser and reboiler duties can be significantly reduced. For two-product distillation, the HIDiC is a favourable alternative to the conventional distillation column....... Energy savings up to 83% are reported for the HIDiC compared to the CDiC, while the reported economical savings are as high as 40%. However, a simpler heat-integrated distillation column configuration exists, which employs compression in order to obtain a direct heat integration between the top vapour...

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1922-07-21

In the distillation of shale and similar materials the shale is ground and briquetted and the briquettes are placed in a retort so that air passages are left between them, after which they are uniformly and slowly heated to at least 700/sup 0/C, the air passages facilitating the escape of the oil vapors, and the slow heating preventing fusion of the flux forming constituents. After the bitumen has been driven off, air is passed into the retort and heating continued to about 1050/sup 0/C, the result being a porous product suitable for insulating purposes or as a substitute for kieselguhr. The ground shale may be mixed prior to distillation with peat, sawdust, or the like, and with substances which yield acids, such as chlorides, more particularly magnesium chloride, the acids acting on the bitumen.

Distilling coal

Energy Technology Data Exchange (ETDEWEB)

Blythe, F C

1914-09-14

In the destructive distillation of bituminous coal, heavy hydrocarbon oil, such as petroleum, kerosine, shale oil, and heavy tar oil, obtained in some cases during the process, is added to the coal, which is then distilled under pressure and at a comparatively low temperature regulated so as to produce a large proportion of hydrocarbon oils and a small proportion of permanent gas. In one method, about 5 to 10 parts of hydrocarbon oil are mixed with 100 parts of crushed or ground coal, and the mixture is heated in a closed vessel, provided in some cases with an agitator, under a pressure of about 60 lb/in/sup 2/, and the temperature may be gradually raised to 350/sup 0/C and then to about 500/sup 0/C. The heating may be by means of superheated steam with or without external heat.

Thermal distillation system utilizing biomass energy burned in stove by means of heat pipe

Directory of Open Access Journals (Sweden)

Hiroshi Tanaka

2016-09-01

Full Text Available A thermal distillation system utilizing a part of the thermal energy of biomass burned in a stove during cooking is proposed. The thermal energy is transported from the stove to the distiller by means of a heat pipe. The distiller is a vertical multiple-effect diffusion distiller, in which a number of parallel partitions in contact with saline-soaked wicks are set vertically with narrow gaps of air. A pilot experimental apparatus was constructed and tested with a single-effect and multiple-effect distillers to investigate primarily whether a heat pipe can transport thermal energy adequately from the stove to the distiller. It was found that the temperatures of the heated plate and the first partition of the distiller reached to about 100 °C and 90 °C, respectively, at steady state, showing that the heat pipe works sufficiently. The distilled water obtained was about 0.75 and 1.35 kg during the first 2 h of burning from a single-effect and multiple-effect distillers, respectively.

Binary and ternary LLE data of the system (ethylbenzene + styrene + 1-ethyl-3-methylimidazolium thiocyanate) and binary VLE data of the system (styrene + 1-ethyl-3-methylimidazolium thiocyanate)

International Nuclear Information System (INIS)

Jongmans, Mark T.G.; Schuur, Boelo; Haan, André B. de

2012-01-01

Highlights: ► LLE data have been measured for the system {ethylbenzene + styrene + [EMIM][SCN]}. ► VLE was determined for the system {styrene + [EMIM][SCN]} at vacuum conditions. ► All experimental data were correlated well with the NRTL model. ► [EMIM][SCN] has a much larger selectivity than the benchmark solvent sulfolane. - Abstract: The distillation of close boiling mixtures may be improved by adding a proper affinity solvent, and thereby creating an extractive distillation process. An example of a close boiling mixture that may be separated by extractive distillation is the mixture ethylbenzene/styrene. The ionic liquid 1-ethyl-3-methylimidazolium thiocyanate ([EMIM][SCN]) is a promising solvent to separate ethylbenzene and styrene by extractive distillation. In this study, (vapour + liquid) equilibrium data have been measured for the binary system (styrene + [EMIM][SCN]) over the pressure range of (3 to 20) kPa and binary and ternary (liquid + liquid) equilibrium data of the system (ethylbenzene + styrene + [EMIM][SCN]) at temperatures (313.2, 333.2 and 353.2) K. Due to the low solubility of ethylbenzene in [EMIM][SCN], it was not possible to measure accurately VLE data of the binary system (ethylbenzene + [EMIM][SCN]) and of the ternary system (ethylbenzene + styrene + [EMIM][SCN]) using the ebulliometer. Because previous work showed that the LLE selectivity is a good measure for the selectivity in VLE, we determined the selectivity with LLE. The selectivity of [EMIM][SCN] to styrene in LLE measurements ranges from 2.1 at high styrene raffinate purity to 2.6 at high ethylbenzene raffinate purity. The NRTL model can properly describe the experimental results. The rRMSD in temperature, pressure and mole fraction for the binary VLE data are respectively (0.1, 0.12 and 0.13)%. The rRMSD is only 0.7% in mole fraction for the LLE data.

On Entropy Generation and the Effect of Heat and Mass Transfer Coupling in a Distillation Process

Science.gov (United States)

Burgos-Madrigal, Paulina; Mendoza, Diego F.; López de Haro, Mariano

2018-01-01

The entropy production rates as obtained from the exergy analysis, entropy balance and the nonequilibrium thermodynamics approach are compared for two distillation columns. The first case is a depropanizer column involving a mixture of ethane, propane, n-butane and n-pentane. The other is a weighed sample of Mexican crude oil distilled with a pilot scale fractionating column. The composition, temperature and flow profiles, for a given duty and operating conditions in each column, are obtained with the Aspen Plus V8.4 software by using the RateFrac model with a rate-based nonequilibrium column. For the depropanizer column the highest entropy production rate is found in the central trays where most of the mass transfer occurs, while in the second column the highest values correspond to the first three stages (where the vapor mixture is in contact with the cold liquid reflux), and to the last three stages (where the highest temperatures take place). The importance of the explicit inclusion of thermal diffusion in these processes is evaluated. In the depropanizer column, the effect of the coupling between heat and mass transfer is found to be negligible, while for the fractionating column it becomes appreciable.

The composition-explicit distillation curve technique: Relating chemical analysis and physical properties of complex fluids.

Science.gov (United States)

Bruno, Thomas J; Ott, Lisa S; Lovestead, Tara M; Huber, Marcia L

2010-04-16

The analysis of complex fluids such as crude oils, fuels, vegetable oils and mixed waste streams poses significant challenges arising primarily from the multiplicity of components, the different properties of the components (polarity, polarizability, etc.) and matrix properties. We have recently introduced an analytical strategy that simplifies many of these analyses, and provides the added potential of linking compositional information with physical property information. This aspect can be used to facilitate equation of state development for the complex fluids. In addition to chemical characterization, the approach provides the ability to calculate thermodynamic properties for such complex heterogeneous streams. The technique is based on the advanced distillation curve (ADC) metrology, which separates a complex fluid by distillation into fractions that are sampled, and for which thermodynamically consistent temperatures are measured at atmospheric pressure. The collected sample fractions can be analyzed by any method that is appropriate. The analytical methods we have applied include gas chromatography (with flame ionization, mass spectrometric and sulfur chemiluminescence detection), thin layer chromatography, FTIR, corrosivity analysis, neutron activation analysis and cold neutron prompt gamma activation analysis. By far, the most widely used analytical technique we have used with the ADC is gas chromatography. This has enabled us to study finished fuels (gasoline, diesel fuels, aviation fuels, rocket propellants), crude oils (including a crude oil made from swine manure) and waste oils streams (used automotive and transformer oils). In this special issue of the Journal of Chromatography, specifically dedicated to extraction technologies, we describe the essential features of the advanced distillation curve metrology as an analytical strategy for complex fluids. Published by Elsevier B.V.

Process for distilling shales, peats, etc

Energy Technology Data Exchange (ETDEWEB)

Felizat, G

1922-01-09

The invention has for its object: a process for the distillation of shales, peats, and analogous products characterized by injecting across the substance a very rapid stream of superheated steam under pressure in order to effect a rapid removal of the products of distillation, to lower also the temperature at which it distills, to equalize the temperature throughout the mass, to hydrogenate the heavy hydrocarbons. An apparatus is put into operation characterized by the combination of a retort receiving the material to be distilled with a superheater for the steam, the combustion products which escape from the hearth of the superheater going to encircle the retort while the steam which comes off the superheater traverses this retort, the pressure of the steam being regulated by a convenient regulator; the products of the distillation result from the simultaneous action of the hot gases and steam on the contents of the retort being, on the other hand, separated at the outlet of this retort by means of cooling in a gas separator, a condenser, and part of the gas after being separated serving to heat the mentioned superheater.

Model predictive control in light naphtha distillation column of gasoline hydrogenation process

Directory of Open Access Journals (Sweden)

Kornkrit Chiewchanchairat

2015-03-01

Full Text Available The main scope of this research is for designing and implementing of model predictive control (MPC on the light naphtha distillation column of gasoline hydrogenation process. This model is designed by using robust multivariable predictive control technology (RMPCT. The performance of MPC controller is better than PID controllers 32.1 % those are comparing by using as the same of objective function and also in the MPC controller can be used for steam optimization that is shown in this research, stream consumption is reduced 6.6 Kg/ m3 of fresh feed.

Hydrotreatment of bio-oil distillates produced from pyrolysis and hydrothermal liquefaction of duckweed: A comparison study.

Science.gov (United States)

Wang, Feng; Tian, Ye; Zhang, Cai-Cai; Xu, Yu-Ping; Duan, Pei-Gao

2018-09-15

A comprehensive comparison of hydrothermal liquefaction (HTL) to the pyrolysis of duckweed was conducted to determine the yields and components of the crude bio-oils and their distillates. The upgrading behaviors of the distillates were thoroughly investigated with the use of used engine oil as a solvent. With all other variables fixed, HTL produced crude bio-oil with a lower H/C ratio (1.28 ± 0.03) than pyrolysis did (1.45 ± 0.04). However, its distillates had a higher H/C ratio (1.60 ± 0.05) and total yield (66.1 ± 2.0 wt%) than pyrolysis (1.46 ± 0.04 and 47.2 ± 1.4 wt%, respectively). Phenolics and nitrogenous heterocycles constituted relatively major proportions of the two crude bio-oils and most of their distillates. Obvious differences in molecular composition between the two crude bio-oils and their distillates were ascribed to the distinct impacts of HTL and pyrolysis and were affected by the distillate temperature. Co-hydrotreating with used engine oil (UEO) provided the upgraded bio-oils much higher H/C ratios (~1.78 ± 0.05) and higher heating values (~45.5 ± 1.4 MJ·kg -1 ), as well as much lower contents of N, O and S compared to their initial distillates. Aromatics and alkanes constituted a large proportion in most of upgraded bio-oils. N removal from the pyrolysis distillates was easier than from the HTL distillates. Distinct differences in yields and molecular compositions for the upgraded bio-oils were also attributed to the different influences associated with the two conversion routes. Copyright © 2018 Elsevier B.V. All rights reserved.

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

Preprototype vapor compression distillation subsystem. [recovering potable water from wastewater

Science.gov (United States)

Ellis, G. S.; Wynveen, R. A.; Schubert, F. H.

1979-01-01

A three-person capacity preprototype vapor compression distillation subsystem for recovering potable water from wastewater aboard spacecraft was designed, assembled, and tested. The major components of the subsystem are: (1) a distillation unit which includes a compressor, centrifuge, central shaft, and outer shell; (2) a purge pump; (3) a liquids pump; (4) a post-treat cartridge; (5) a recycle/filter tank; (6) an evaporator high liquid level sensor; and (7) the product water conductivity monitor. A computer based control monitor instrumentation carries out operating mode change sequences, monitors and displays subsystem parameters, maintains intramode controls, and stores and displays fault detection information. The mechanical hardware occupies 0.467 m3, requires 171 W of electrical power, and has a dry weight of 143 kg. The subsystem recovers potable water at a rate of 1.59 kg/hr, which is equivalent to a duty cycle of approximately 30% for a crew of three. The product water has no foul taste or odor. Continued development of the subsystem is recommended for reclaiming water for human consumption as well as for flash evaporator heat rejection, urinal flushing, washing, and other on-board water requirements.

Seawater desalination with solar-energy-integrated vacuum membrane distillation system

Directory of Open Access Journals (Sweden)

Fang Wang

2017-03-01

Full Text Available This study designed and tested a novel type of solar-energy-integrated vacuum membrane distillation (VMD system for seawater desalination under actual environmental conditions in Wuhan, China. The system consists of eight parts: a seawater tank, solar collector, solar cooker, inclined VMD evaporator, circulating water vacuum pump, heat exchanger, fresh water tank, and brine tank. Natural seawater was used as feed and a hydrophobic hollow-fiber membrane module was used to improve seawater desalination. The experiment was conducted during a typical summer day. Results showed that when the highest ambient temperature was 33 °C, the maximum value of the average solar intensity was 1,080 W/m2. The system was able to generate 36 kg (per m2 membrane module distilled fresh water during 1 day (7:00 am until 6:00 pm, the retention rate was between 99.67 and 99.987%, and electrical conductivity was between 0.00276 and 0.0673 mS/cm. The average salt rejection was over 90%. The proposed VMD system shows favorable potential application in desalination of brackish waters or high-salt wastewater treatment, as well.

The features of ultrapurification of cadium by distillation method

International Nuclear Information System (INIS)

Kozin, L.F.; Berezhnoj, E.O.; Kozin, K.L.

1996-01-01

The linear dependence of the coefficients of interphase distribution of liquid-vapour is found in the systems cadmium-accompanying impurities upon the evaporation enthalpy. The values of α are calculated for 52 accompanying impurities. The vacuum distillation of cadmium at different experimental conditions. It is shown that during distillation of cadmium at the optimum conditions the content of 14 accompanying impurities is 1.78x10 -7 mass. %, and the assumed content of the main metal is 8N8 of cadmium. The total separation coefficient is 2.1x10 4

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Armour, J; Armour, H

1889-05-07

The invention relates to retorts and accessory apparatus for distilling shale or other oil-yielding minerals. A series of long vertical retorts, composed of fire-brick or similar refractory material, are arranged in two rows in a bench, being divided into groups of four by transverse vertical partitions. The retorts are surmounted by metal casings or hoppers into which the fresh mineral is charged, and from which the distillate passes off through lateral pipes. Any uncondensed gases from the retorts may be passed into the flues surrounding them by the pipe and burned. The products of combustion from a furnace pass through a series of horizontal flues, being compelled to pass completely round each retort before entering the flue above. The products from two or more sets pass from the upper flues into flues running along the top of the bench, and return through a central flue to the chimney.

Thermodynamic evaluation of distillation columns using exergy loss profiles: a case study on the crude oil atmospheric distillation column

Energy Technology Data Exchange (ETDEWEB)

Tarighaleslami, Amir Hossein [Mahshahr Branch, Islamic Azad University, Chemical Engineering Faculty, Mahshar, Khouzestan (Iran, Islamic Republic of); Omidkhah, Mohammad Reza [Tarbiat Modares University, Chemical Engineering Department, Faculty of Engineering, Tehran (Iran, Islamic Republic of); Ghannadzadeh, Ali [University of Toulouse, Department of Process and System Engineering, Chemical Engineering Laboratory, Toulouse (France); Hoseinzadeh Hesas, Roozbeh [University of Malaya, Chemical Engineering Department, Faculty of Engineering, Kuala Lumpur (Malaysia)

2012-06-15

This paper presents a case study on the crude oil atmospheric distillation column of Tabriz refinery plant to show the applicability of exergy loss profiles in thermodynamic examination of the different retrofit options. The atmospheric distillation column of Tabriz refinery has been revamped as a consequence of increase of the plant capacity to 100,000 bpd. To cover the deficit of feedstock of the revamped unit, a blend of the existing feedstock with imported crude oil is used as a feedstock. However, to investigate how the blend of these two different types of crudes as a feedstock has an influence on the operating conditions, the examination of the column is needed. Exergy as a comprehensive thermodynamic property which translates the temperature, pressure and composition change into a common unit has been chosen to evaluate the distillation column thermodynamically. Furthermore, the exergy loss profile of the base case serves as a scoping tool to pinpoint the source of inefficiencies. Then, the exergy loss profile as a screening tool has found the retrofit options which are likely to yield greatest energy saving from a list of retrofit options proposed by the industrial partner. In the presented case study, the exergy loss profile identifies the best retrofit option with 17.16% reduction in exergy losses, which finally lead to 3.6% reduction of primary fuel demand. (orig.)

New method dynamically models hydrocarbon fractionation

Energy Technology Data Exchange (ETDEWEB)

Kesler, M.G.; Weissbrod, J.M.; Sheth, B.V. [Kesler Engineering, East Brunswick, NJ (United States)

1995-10-01

A new method for calculating distillation column dynamics can be used to model time-dependent effects of independent disturbances for a range of hydrocarbon fractionation. It can model crude atmospheric and vacuum columns, with relatively few equilibrium stages and a large number of components, to C{sub 3} splitters, with few components and up to 300 equilibrium stages. Simulation results are useful for operations analysis, process-control applications and closed-loop control in petroleum, petrochemical and gas processing plants. The method is based on an implicit approach, where the time-dependent variations of inventory, temperatures, liquid and vapor flows and compositions are superimposed at each time step on the steady-state solution. Newton-Raphson (N-R) techniques are then used to simultaneously solve the resulting finite-difference equations of material, equilibrium and enthalpy balances that characterize distillation dynamics. The important innovation is component-aggregation and tray-aggregation to contract the equations without compromising accuracy. This contraction increases the N-R calculations` stability. It also significantly increases calculational speed, which is particularly important in dynamic simulations. This method provides a sound basis for closed-loop, supervisory control of distillation--directly or via multivariable controllers--based on a rigorous, phenomenological column model.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bennett, J M

1884-06-03

The invention relates to retorts for the destructive distillation of shale, dross, and other carbonaceous or oleaginous materials, and for the distillation and carbonization of sawdust, shavings, tan bark, and the like. The material is fed from a trapped hopper on a series of trays or casings of cast iron or other material, separated by flue spaces and arranged in a tier round a vertical rotating shaft passing through tubular pieces cast on the casings. The shaft is fitted with arms which carry stirring-blades so disposed that the material is shifted from side to side and slowly fed towards the ducts through which it passes to the casing next below, and is finally withdrawn from the apparatus by a pipe, which may be trapped or otherwise. Furnace gases are admitted through openings in the enclosing brickwork having settings to support the casings, the lowermost of which may be fitted below the inlet for furnace gases and their contents cooled by the circulation of cold water round them. The gaseous or volatile products of distillation pass to a condenser by means of openings and the pipe, which may be formed in sections to obtain access to the casings, or doors may be provided for this purpose. The ducts may be arranged alternately at the edge and center of the casings, which may be jacketed, and heated air or steam may be employed instead of furnace gases. Means may also be provided for admitting superheated steam into one or more of the casings.

Patchouli Oil Production for Fixative Aromatheraphy: A Case Study Design of Condenser for Steam Distillation

Directory of Open Access Journals (Sweden)

Egi Agustian

2015-06-01

Full Text Available Patchouli oil is an important material for aromatherapy industries and made from patchouli leaves by steam distillation. The important parts of steam distillation is condenser. The problem is process of farmer's patchouli based on experience not used chemical process of steam distillation cause not effective and efficient. The study was designed of condensers on steam distillation for patchouli leaves. Specification of condenser type is shell and tube, stainless steel material and water as coolant. Tubing sized is ¼ inch with 500 mm of length and 24 pieces. Shell measuring 2.5 inch and 600 mm of length. The performance of condenser gave the efficiency at 94.51%. The process condition of ratio stems to leaves is 5:6 and 4.5 hours was considered ideal for steam distillation. The used of energy is lowest cause the efficiency condenser and yield will be higher. Patchouli oil yield of 2.39% and patchouli alcohol content is 35.65%.

7 CFR 160.9 - Destructively distilled wood turpentine.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Destructively distilled wood turpentine. 160.9 Section... REGULATIONS AND STANDARDS FOR NAVAL STORES General § 160.9 Destructively distilled wood turpentine. The designation “destructively distilled wood turpentine” shall refer to the kind of spirits of turpentine...

Use of solar distillation for olive mill wastewater drying and recovery of polyphenolic compounds.

Science.gov (United States)

Sklavos, Sotirios; Gatidou, Georgia; Stasinakis, Athanasios S; Haralambopoulos, Dias

2015-10-01

Olive mill wastewater (OMW) is characterized by its high organic load and the presence of phenolic compounds. For first time, a solar distillator was used to investigate the simultaneous solar drying of OMW and the recovery of phenolic compounds with antioxidant properties in the distillate. Two experiments were conducted and the role of thermal insulation on the performance of the distiller was studied. The use of insulation resulted to higher temperatures in the distillator (up to 84.3 °C and 78.5 °C at the air and sludge, respectively), shorter period for OMW dewatering (14 days), while it increased the performance of distillator by 26.1%. Chemical characterization of the distillate showed that pH and COD concentration gradually decreased during the experiments, whereas an opposite trend was noticed for conductivity and total phenols concentration. Almost 4% of the total phenols found initially in OMW were transferred to the distillate when an insulated solar distillator was used. Gas chromatographic analysis of collected distillates confirmed the presence of tyrosol in all samples; whereas hydroxytyrosol was found only in fresh collected distillate samples. Further experiments should be conducted to optimize the process and quantify the concentrations of recovered phenolic compounds. Copyright © 2015 Elsevier Ltd. All rights reserved.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Irvine, R

1884-04-04

In obtaining paraffin by distillation of shales, etc., containing sulfur, the steam used for heating is charged with ammonia or ammonium carbonate in suspension. This prevents the sulfur from decomposing the paraffin. The ammonia, etc., may also be used alone or in solution in water.

Removal of salt from rare earth precipitates by vacuum distillation

International Nuclear Information System (INIS)

Yang, Hee-Chul; Eun, Hee-Chul; Cho, Yong-Zun; Park, Hwan-Seo; Kim, In-Tae

2008-01-01

This study investigated the distillation rates of LiCl-KCl eutectic salt from the rare earth (RE) precipitates originating from the oxygen-sparging RE precipitation process. The first part study investigated distillation rates of eutectic salt under different vacuums at high temperatures by using thermo-gravimetric furnace system. The second part study tested the removal efficiency of eutectic salt from RE precipitates by using the laboratory vacuum distillation furnace system. Investigated variables were the temperature, the degree of vacuum and the time. Salt distillation operation with a moderated distillation rate of 10 -4 - 10 -5 mole sec -1 cm -2 is possible at temperature less than 1300 K and vacuums of 5-50 Torr, by minimizing the potentials of the RE particle entrainment. An increase in the vaporizing surface area is relatively effective for removing the residual salt in pores of bulk of the precipitated RE particles, when compared to that for the vaporizing time. Over 99.9% of the salt removal from the salt-RE precipitate mixture could be achieved by increasing the vaporizing surface area under moderate vacuum conditions of 50 Torr at 1200 K. (author)

A method for refining oil

Energy Technology Data Exchange (ETDEWEB)

Bruskin, Yu.A.; Gorokhov, V.V.; Kotler, L.D.; Kovalenko, N.F.; Spasskiy, Yu.B.; Titov, A.M.; Vlasenko, V.Ye.; Vytnov, V.A.

1983-01-01

In the method for refining oil through its distillation with the isolation of directly distilled gases and a benzine fraction (BS) with the use of a benzine fraction pyrolysis, in order to increase the output of the lower olefines and to reduce the energy expenditures, the distillation is conducted with the isolation of 10 to 40 percent of the benzine fraction from its potential content along with the directly distilled gases. The obtained mixture of the remaining part of the benzine fraction is absorbed at a pressure of 1.5 to 6 atmospheres with the feeding of the obtained saturated absorbent to pyrolysis and subsequent mixing of the obtained pyrolysis gas with the unabsorbed product and their joint gas division. As compared to the known method, the proposed method makes it possible to reduce the energy expenditures which is achieved through a reduction in the volume of irrigation in the tower, and to increase the output of the olefines through processing of the steam and gas mixture of the benzine and the directly distilled gases.

Optimization of Palmitic Acid Composition in Crude Oleic Acid to Provide Specifications of Titer and Cloud Point of Distillate Oleic Acid using a Flash Distiller

Directory of Open Access Journals (Sweden)

Muhammad Yusuf Ritonga

2010-11-01

Full Text Available Titer and cloud point of Distilled Oleic Acid is higher than is the standard on feed composition palmitic acid (C15H31COOH or C16 11.2 %. Feed composition C16, top temperature precut and bottom main distiller column were optimized to produce DOA. A factorial design with 3 independent variables, 3 X 2 X 3, repeated twice as much, is applied to observe effects of feed composition C16 to quality parameters. In the optimum C16, feed composition at 5.20 % produced DOA with titer 6.8 oC, cloud point 5.0 oC (inside its specification.

Distillation process using microchannel technology

Science.gov (United States)

Tonkovich, Anna Lee [Dublin, OH; Simmons, Wayne W [Dublin, OH; Silva, Laura J [Dublin, OH; Qiu, Dongming [Carbondale, IL; Perry, Steven T [Galloway, OH; Yuschak, Thomas [Dublin, OH; Hickey, Thomas P [Dublin, OH; Arora, Ravi [Dublin, OH; Smith, Amanda [Galloway, OH; Litt, Robert Dwayne [Westerville, OH; Neagle, Paul [Westerville, OH

2009-11-03

The disclosed invention relates to a distillation process for separating two or more components having different volatilities from a liquid mixture containing the components. The process employs microchannel technology for effecting the distillation and is particularly suitable for conducting difficult separations, such as the separation of ethane from ethylene, wherein the individual components are characterized by having volatilities that are very close to one another.

Determination of Methanol Content in Herbal Distillates Produced in Urmia Using Spectrophotometry

Directory of Open Access Journals (Sweden)

Mohammad Delirrad

2012-05-01

Full Text Available Background: Herbal distillates have been used for many centuries as drinks, flavors, and herbal medicine in Iran, especially in the city of Urmia. Recently, some studies claimed the presence of methanol in different types of herbal distillates. Methanol is a highly toxic compound which can cause acute or chronic toxicity in humans. Acute poisoning with methanol can cause different complications and even death while chronic methanol exposure has a wide range of nonspecific and misleading findings. The main purpose of this study was to determine methanol content in the commonly-used industrial herbal distillates produced in Urmia. Methods: Five samples of six types of most commonly used herbal distillates (peppermint, musk willow, lemon balm, pennyroyal, dill, and rose water were purchased from five active herbal distillates manufacturers in Urmia. All samples were transferred to the laboratory and methanol content of each sample was measured two times according to the standard method of analysis using spectrophotometer. Results: The lowest and highest concentration of methanol were found in rose water (mean=72.4±32.1 ppm and musk willow (mean=278.3±106 ppm samples, respectively. One-way ANOVA showed statistically significant differences among methanol concentrations in the studied herbal distillates (F=60.9, P <0.001. Discussion: Different amounts of methanol were found in herbal distillates and it seems that there are statistically significant differences in methanol concentrations of various types of herbal distillates. Therefore, considering the harmful effects of methanol on human health, further studies are required for determining permitted levels of methanol in herbal distillates.

Study of the properties of the anthracene fraction by the thermogravimetric method

Energy Technology Data Exchange (ETDEWEB)

Belkina, T.V.; Chernyak, P.E.; Ulanovskii, M.L.

1980-01-01

With the use of the TGA method, the effect of temperature, thermal exposure time, a179975d the medium on the relation of the rates and the intensity of the processes of distillation and synthesis during thermal treatment of the anthracene fraction were determined.

Fate of Fumonisin B1 in Naturally Contaminated Corn during Ethanol Fermentation

Science.gov (United States)

Bothast, R. J.; Bennett, G. A.; Vancauwenberge, J. E.; Richard, J. L.

1992-01-01

Two lots of corn naturally contaminated with fumonisin B1 (15 and 36 ppm) and a control lot (no fumonisin B1 detected) were used as substrates for ethanol production in replicate 8.5-liter yeast fermentations. Ethanol yields were 8.8% for both the control and low-fumonisin corn, while the high-fumonisin corn contained less starch and produced 7.2% ethanol. Little degradation of fumonisin occurred during fermentation, and most was recovered in the distillers' grains, thin stillage, and distillers' solubles fractions. No toxin was detected in the distilled alcohol or centrifuge solids. Ethanol fermentation of fumonisin-contaminated corn coupled with effective detoxification of distillers' grains and aqueous stillage is suggested as a practical process strategy for salvaging contaminated corn. PMID:16348623

Performance indicators of bioethanol distillation

International Nuclear Information System (INIS)

Marriaga, Nilson

2009-01-01

The increase of biofuels demand accelerates the construction of new production plants and technological improvements in the process so the development of versatile tools for evaluating alternatives becomes an undeniable challenge. It was established through heuristic rules, thermodynamic analysis and simulation computer the energy consumption and performance indicators that govern, from fermented mash (ethanol 8.5 % v/v), the distillation of various capacities for bioethanol production: 20, 60, 100 and 150 KLD (kiloliters / day) through Aspen PlusTM simulator. It was found that the distillation demand nearly 30% of heat that would be obtained by burning alcohol fuel produced thus it is necessary the use of raw materials that generate enough biomass to produce the steam required. In addition, correlations were found to allow for easy diameters of distillation columns in terms of production capacity.

7 CFR 58.331 - Starter distillate.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Starter distillate. 58.331 Section 58.331 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.331 Starter distillate. The refined flavor components when used to flavor butter and related...

Performance simulation of the JPL solar-powered distiller. Part 1: Quasi-steady-state conditions. [for cooling microwave equipment

Science.gov (United States)

Yung, C. S.; Lansing, F. L.

1983-01-01

A 37.85 cu m (10,000 gallons) per year (nominal) passive solar powered water distillation system was installed and is operational in the Venus Deep Space Station. The system replaced an old, electrically powered water distiller. The distilled water produced with its high electrical resistivity is used to cool the sensitive microwave equipment. A detailed thermal model was developed to simulate the performance of the distiller and study its sensitivity under varying environment and load conditions. The quasi-steady state portion of the model is presented together with the formulas for heat and mass transfer coefficients used. Initial results indicated that a daily water evaporation efficiency of 30% can be achieved. A comparison made between a full day performance simulation and the actual field measurements gave good agreement between theory and experiment, which verified the model.

Use of an Electronic Tongue to Detect Geosmin in Distilled Water

Science.gov (United States)

Braga, Guilherme S.; Paterno, Leonardo G.; Fonseca, Fernando J.

2011-11-01

An electronic tongue (ET) system consisting of conducting polymer sensors was employed to detect geosmin (GSM) in distilled water. GSM is a tainting compound and known to cause undesirable tastes and odors in water and aquaculture farming. Diluted solutions of GSM were prepared in distilled water at different concentrations. The electrical response (capacitance) of the sensors was analyzed using principal analysis component (PCA). The data obtained were separated into different clusters indicating a good sensibility of the ET system to this compound in distilled water. The ET showed signal saturation for concentrations higher than 300 ng.L-1. So far, the detection limit of our system is 25 ng.L-1. Nevertheless, close grouping between repeated tests indicated that the ET system response is reproducible.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Allison, C A

1906-05-22

The invention relates to an apparatus in which the destructive distillation or coking of coal, peat, shale, etc., is carried out by means of a current of hot gases at a temperature of 700--800/sup 0/F., as described in Specification No. 11,925, A.D. 1906.

Optimization study of distillation column based on Type I absorption heat pump

International Nuclear Information System (INIS)

Li, Yan; Wang, Lu; Zhu, Meng; Wang, Weiqin

2017-01-01

Highlights: • Propose a new distillation system based on Type I absorption heat pump. • The optimum condition of the system is obtained. • The energy consumption of the system is reduced by 23.3% significantly. • The benefits of economy and energy-saving for the new distillation system are distinct. - Abstract: Due to the thermodynamic deficiencies in general pressurized distillation process, a new distillation system based on Type I AHP (absorption heat pump) is proposed in this paper. The proposed system uses AHP to recover the waste heat from column condenser and reheat the feed materials of column; meanwhile, the cooling capacity of column condenser can be increased, which leads to the decrease of the pressure in distillation column. With general distillation system of depropanizing column (C-101) as an example, using numerical simulation software Aspen Plus, the effect of inner parameters on the energy consumption has been conducted to approach the general rules of energy saving in distillation. Then the new distillation system is adopted and the optimization of its energy consumption is conducted to determine the optimum operating condition. The numerical simulation results show that the steam consumption can be decreased by 23.3% compared with general C-101 system, reaching the minimum. Moreover, the extra heat output of AHP is treated as the heat source for the reboilers of deethanization column (C-102) and refined propylene column (C-103), which reduces the total steam consumption of three-column processes by 22.1%.

Wine distillates: practical operating recipe formulation for stills.

Science.gov (United States)

Osorio, Daniel; Pérez-Correa, J Ricardo; Biegler, Lorenz T; Agosin, Eduardo

2005-08-10

Consumer perceptions of flavors are associated with the chemical composition of foods. However, consumer preferences change; therefore, it is necessary for food manufacturers to be able to adapt their products. Unlike in aged spirits, the chemical composition of young spirits is determined during distillation; therefore, this is where distillers must tailor their operating recipes to the new trends. Even for an experienced distiller, the complexity of the process makes adapting the operating recipe far from straightforward. In this study, we developed a methodology for generating practical recipes that makes use of computer simulations and optimization techniques. We used Pisco Brandy, a young Muscat wine distillate from Chile and Peru as our case study. Even so, because our methodology is independent of the chemical composition of the broth, it can be applied throughout the industry. Drawing on the experience and preferences of industry enologists, we designed a preferred distillate and used our methodology to obtain the appropriate recipe. This recipe was validated in lab scale experiments, and we obtained a much closer distillate to the desired prescription than commercial products.

The use of tomato aminoaldehyde dehydrogenase 1 for the detection of aldehydes in fruit distillates.

Science.gov (United States)

Frömmel, Jan; Tarkowski, Petr; Kopečný, David; Šebela, Marek

2016-09-25

Plant NAD(+)-dependent aminoaldehyde dehydrogenases (AMADHs, EC 1.2.1.19) belong to the family 10 of aldehyde dehydrogenases. They participate in the metabolism of polyamines or osmoprotectants. The enzymes are characterized by their broad substrate specificity covering ω-aminoaldehydes, aliphatic and aromatic aldehydes as well as nitrogen-containing heterocyclic aldehydes. The isoenzyme 1 from tomato (Solanum lycopersicum; SlAMADH1) oxidizes aliphatic aldehydes very efficiently and converts also furfural, its derivatives or benzaldehyde, which are present at low concentrations in alcoholic distillates such as fruit brandy. In this work, SlAMADH1 was examined as a bioanalytical tool for their detection. These aldehydes arise from fermentation processes or thermal degradation of sugars and their presence is related to health complications after consumption including nausea, emesis, sweating, decrease in blood pressure, hangover headache, among others. Sixteen samples of slivovitz (plum brandy) from local producers in Moravia, Czech Republic, were analyzed for their aldehyde content using a spectrophotometric activity assay with SlAMADH1. In all cases, there were oxidative responses observed when monitoring NADH production in the enzymatic reaction. Aldehydes in the distillate samples were also subjected to a standard determination using reversed-phase HPLC with spectrophotometric and tandem mass spectrometric detection after a derivatization with 2,4-dinitrophenylhydrazine. Results obtained by both methods were found to correlate well for a majority of the analyzed samples. The possible applicability of SlAMADH1 for the evaluation of aldehyde content in food and beverages has now been demonstrated. Copyright © 2015 Elsevier B.V. All rights reserved.

Vacuum distillation of plutonium pyrochemical salts

International Nuclear Information System (INIS)

Bourges, Gilles; Faure, S.; Fiers, B.; Saintignon, S.; Lemoine, O.; Cardona-Barrau, D.; Devillard, D.

2012-01-01

A pyrochemical process is developed to upgrade the safety of plutonium spent salts interim storage. The feed material, consisting of alkali or alkali-earth chlorides containing various Pu and Am species, is first oxidized to convert the actinides into oxides. Then the chlorides are removed by vacuum distillation which requires temperature from 750 degrees C to 1100 degrees C. After a comprehensive R and D program, full-scale equipment was built to test the distillation of active salts. Tests with NaCl/KCl oxidized spent salt give decontamination factor of chlorides higher than 20000. The distilled salt meets the radiologic requirements to be discarded as low level waste. (authors)

Method and arrangement of distillation of shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1920-03-29

A method is given of distilling shale and other bituminous materials utilizing the heat from the combustion of the residue, possibly with additional heat from other fuels. It is characterized by the shale, which is arranged in layers, being first submitted to a process of distillation utilizing the heat mentioned, and at the same time recovering the products of distillation, and second the shale being burned without disturbing the layers to any appreciable extent. The patent has 16 more claims.

Upgrading of syngas hydrotreated fractionated oxidized bio-oil to transportation grade hydrocarbons

International Nuclear Information System (INIS)

Luo, Yan; Hassan, El Barbary; Guda, Vamshi; Wijayapala, Rangana; Steele, Philip H.

2016-01-01

Highlights: • Hydrotreating of fractionated oxidized bio-oil with syngas was feasible. • Hydrocarbon properties were similar with all syngas H_2/CO molar ratios except viscosity. • Syngas with H_2/CO molar ratio of (4:6) produced the highest hydrocarbon yield. • The produced hydrocarbons were in the range of gasoline, jet fuel and diesel boiling points. - Abstract: Fast pyrolysis bio-oils have the potential to replace a part of transportation fuels obtained from fossil. Bio-oil can be successfully upgraded into stable hydrocarbons (gasoline, jet fuel and diesel) through a two-stage hydrodeoxygenation process. Consumption large amount of expensive hydrogen during this process is the major hurdle for commercialization of this technology. Applying syngas in the hydrotreating step can significantly reduce the cost of the whole process and make it competitive. In this study, four different models of syngas with different H_2 concentrations (H_2/CO molar ratios = 2:8, 4:6, 6:4 and 8:2) were used for the 1st-stage hydrotreating step of oxidized fractionated bio-oil (OFB). The 2nd-stage hydrocracking step was performed on the produced organic liquid products (OLPs) by using pure H_2 gas. The effect of syngas H_2 concentrations on the yields and properties of OLPs and the 2nd-stage hydrocarbons (HCs) was investigated. Physical and chemical properties of the 2nd-stage hydrocarbons were similar regardless syngas H_2 content, with the exception of the viscosity. Syngas with H_2/CO molar ratio of 4:6 gave significantly highest HCs yield (24.8 wt.%) based on the OFB. Simulated distillation analysis proved that all 2nd-stage hydrocarbons were mixture from a wide range boiling point fuels. These results also indicated that the successful 1st-stage syngas hydrotreating step was having the potential to produce different hydrocarbons.

KINETIC MODELS STUDY OF HYDRODESULPHURIZATION VACUUM DISTILLATE REACTION

Directory of Open Access Journals (Sweden)

AbdulMunem A. Karim

2013-05-01

Full Text Available    This study deals with  kinetics of hydrodesulphurization (HDS reaction of vacuum gas oil (611-833 K which was distillated from Kirkuk crude oil and which was obtained by blending the fractions, light vacuum gas oil (611 - 650 K, medium vacuum gas oil (650-690 K, heavy vacuum gas oil (690-727 K and very heavy vacuum gas oil (727-833 K.   The vacuum gas oil was hydrotreated on a commercial cobalt-molybdenum alumina catalyst presulfied at specified conditions in a laboratory trickle bed reactor. The reaction temperature range (583-643 K,liquid hourly space velocity range (1.5-3.75 h-1 and hydrogen pressure was kept constant at 3.5 MPa with hydrogen to oil ratio about 250 lt/lt.           The conversion results for desulphurization reaction appeared to obey the second order reaction. According to this model, the rate constants for desulphurization reaction were determined. Finally, the apparent activation energy (Ea, enthalpy of activation ( H* and entropy ( S* were calculated based on the values of rate constant (k2 and were equal 80.3792 KJ/mole, 75.2974 KJ/mole and 197.493 J/mole, respectively.

Membrane distillation against a pressure difference

NARCIS (Netherlands)

Keulen, L.; Ham, L.V. van der; Kuipers, N.J.M.; Hanemaaijer, J.H.; Vlugt, T.J.H.; Kjelstrup, S.

2017-01-01

Membrane distillation is an attractive technology for production of fresh water from seawater. The MemPower® concept, studied in this work, uses available heat (86 °C) to produce pressurized water (2.2 bar and 46 °C) by membrane distillation, which again can be used to power a turbine for

In vitro anthelmintic effects of Spigelia anthelmia protein fractions against Haemonchus contortus.

Directory of Open Access Journals (Sweden)

Sandra Alves Araújo

Full Text Available Gastrointestinal nematodes are a significant concern for animal health and well-being, and anthelmintic treatment is mainly performed through the use of chemical products. However, bioactive compounds produced by plants have shown promise for development as novel anthelmintics. The aim of this study is to assess the anthelmintic activity of protein fractions from Spigelia anthelmia on the gastrointestinal nematode Haemonchus contortus. Plant parts were separated into leaves, stems and roots, washed with distilled water, freeze-dried and ground into a fine powder. Protein extraction was performed with sodium phosphate buffer (75 mM, pH 7.0. The extract was fractionated using ammonium sulfate (0-90% and extensively dialyzed. The resulting fractions were named LPF (leaf protein fraction, SPF (stem protein fraction and RPF (root protein fraction, and the protein contents and activities of the fractions were analyzed. H. contortus egg hatching (EHA, larval exsheathment inhibition (LEIA and larval migration inhibition (LMIA assays were performed. Proteomic analysis was conducted, and high-performance liquid chromatography (HPLC chromatographic profiles of the fractions were established to identify proteins and possible secondary metabolites. S. anthelmia fractions inhibited H. contortus egg hatching, with LPF having the most potent effects (EC50 0.17 mg mL-1. During LEIA, SPF presented greater efficiency than the other fractions (EC50 0.25 mg mL-1. According to LMIA, the fractions from roots, stems and leaves also reduced the number of larvae, with EC50 values of 0.11, 0.14 and 0.21 mg mL-1, respectively. Protein analysis indicated the presence of plant defense proteins in the S. anthelmia fractions, including protease, protease inhibitor, chitinase and others. Conversely, secondary metabolites were absent in the S. anthemia fractions. These results suggest that S. anthelmia proteins are promising for the control of the gastrointestinal nematode H

Scatter fractions from linear accelerators with x-ray energies from 6 to 24 MV.

Science.gov (United States)

Taylor, P L; Rodgers, J E; Shobe, J

1999-08-01

Computation of shielding requirements for a linear accelerator must take into account the amount of radiation scattered from the patient to areas outside the primary beam. Currently, the most frequently used data are from NCRP 49 that only includes data for x-ray energies up to 6 MV and angles from 30 degrees to 135 degrees. In this work we have determined by Monte Carlo simulation the scattered fractions of dose for a wide range of energies and angles of clinical significance including 6, 10, 18, and 24 MV and scattering angles from 10 degrees to 150 degrees. Calculations were made for a 400 cm2 circular field size impinging onto a spherical phantom. Scattered fractions of dose were determined at 1 m from the phantom. Angles from 10 degrees to 30 degrees are of concern for higher energies where the scatter is primarily in the forward direction. An error in scatter fraction may result in too little secondary shielding near the junction with the primary barrier. The Monte Carlo code ITS (Version 3.0) developed at Sandia National Laboratory and NIST was used to simulate scatter from the patient to the barrier. Of significance was the variation of calculated scattered dose with depth of measurement within the barrier indicating that accurate values may be difficult to obtain. Mean energies of scatter x-ray spectra are presented.

Evolution of Volatile Compounds during the Distillation of Cognac Spirit.

Science.gov (United States)

Awad, Pierre; Athès, Violaine; Decloux, Martine Esteban; Ferrari, Gérald; Snakkers, Guillaume; Raguenaud, Patrick; Giampaoli, Pierre

2017-09-06

Cognac wine spirit has a complex composition in volatile compounds which contributes to its organoleptic profile. This work focused on the batch distillation process and, in particular, on volatile compounds specifically produced by chemical reactions during the distillation of Cognac wine spirit, traditionally conducted in two steps with charentais pot stills. The aim of this study was to characterize these volatile compounds formed during distillation. Sampling has been performed on the distillates and inside the boiler during a typical Cognac distillation. The analysis of these samples allowed us to perform a mass balance and to point out several types of volatile compounds whose quantities strongly increased during the distillation process. These compounds were distinguished by their chemical family. It has been found that the first distillation step was decisive for the formation of volatile compounds. Moreover, 2 esters, 3 aldehydes, 12 norisoprenoids, and 3 terpenes were shown to be generated during the process. These results suggest that some volatile compounds found in Cognac spirit are formed during distillation due to chemical reactions induced by high temperature. These findings give important indications to professional distillers in order to enhance the product's quality.

Influence of fractionation and time on local control of T1 and T2 glottic carcinoma

International Nuclear Information System (INIS)

Le, Quynh-Thu; Krieg, Richard M.; Quivey, Jeanne M.; Fu, Karen K.; Meyler, Thomas S.; Stuart, Alex A.; Phillips, Theodore L.

1996-01-01

Purpose: To evaluate the influence of fraction size and overall time on local control of T1 and T2 glottic carcinoma Methods and Materials: Between 1956 and 1995, 318 consecutive patients with early glottic carcinoma (250 T1, 68 T2) were treated with definitive megavoltage radiotherapy at UCSF. Treatment was delivered using conventional fractionation at one fraction/day, 5 days/week. Minimum tumor dose ranged from 50 to 81Gy (median: 61Gy). The fraction size was 200cGy. Conclusions: Risk of tumor recurrence increased with higher T-stage, smaller fraction size, and longer overall time. Our results suggest that for optimal local control, radiotherapy for early glottic carcinoma should be completed as soon as possible, preferably within 6 weeks, using a fraction size ≥ 225cGy. Our current policy is to treat T1 and T2 vocal cord carcinomas with 225cGy/fraction/day, 5 days/week to a total dose of 63-65Gy

From batch to continuous extractive distillation using thermodynamic insight: class 1.0-2 case B

OpenAIRE

Shen, Weifeng; Benyounes, Hassiba; Gerbaud, Vincent

2011-01-01

A systematic feasibility analysis is presented for the separation azeotropic mixtures by batch and continuous extractive distillation. Based on batch feasibility knowledge, batch and continuous separation feasibility is studied under reflux ratio and entrainer flow-rate for the ternary system chloroform-vinyl acetate-butyl acetate, which belongs to the class 1.0-2 separating maximum boiling temperature azeotropes using a heavy entrainer. How information on feasibility of batch mode could be e...

Membrane distillation against a pressure difference

NARCIS (Netherlands)

Keulen, L.; van der Ham, LV; Kuipers, N.J.M.; Hanemaaijer, J.H.; Vlugt, T.J.H.; Kjelstrup, S

2017-01-01

Membrane distillation is an attractive technology for production of fresh water from seawater. The MemPower®MemPower® concept, studied in this work, uses available heat (86 °C) to produce pressurized water (2.2 bar and 46 °C) by membrane distillation, which again can be used to power a turbine for

Process of distillation of oil shale

Energy Technology Data Exchange (ETDEWEB)

Saxton, A L

1968-08-16

In an oil-shale distillation apparatus with a single retort, in which separate zones of preheating, distillation, combustion, and cooling are maintained, the operation is conducted at a presssure higher than the atmospheric pressure, preferably at a gage pressure between about 0.35 and 7.0 bars. This permits increasing the capacity of the installation.

Thermodynamic analysis of multicomponent distillation columns: identifying optimal feed conditions

Directory of Open Access Journals (Sweden)

M. L.O. Maia

2000-12-01

Full Text Available A new methodology for the optimisation of feed conditions as well as the calculation of minimum reflux ratio of distillation columns is presented. The reversible profile approach used for saturated liquid feeds is extended to consider other feed conditions. For flashed feed, the liquid fraction of the feed stream is used to compute the column pinch conditions and the minimum reflux ratio. The modifications required for subcooled liquid and superheated vapor feed are discussed, and a procedure to estimate the minimum reflux for those conditions is proposed. The methodology presented allows the identification of the optimal feed condition, without having to resort to a full stage-by-stage procedure.

Low grade bioethanol for fuel mixing on gasoline engine using distillation process

Science.gov (United States)

Abikusna, Setia; Sugiarto, Bambang; Suntoro, Dedi; Azami

2017-03-01

Utilization of renewable energy in Indonesia is still low, compared to 34% oil, 20% coal and 20% gas, utilization of energy sources for water 3%, geothermal 1%, 2% biofuels, and biomass 20%. Whereas renewable energy sources dwindling due to the increasing consumption of gasoline as a fuel. It makes us have to look for alternative renewable energy, one of which is bio ethanol. Several studies on the use of ethanol was done to the researchers. Our studies using low grade bio ethanol which begins with the disitillation independently utilize flue gas heat at compact distillator, produces high grade bio ethanol and ready to be mixed with gasoline. Stages of our study is the compact distillator design of the motor dynamic continued with good performance and emission testing and ethanol distilled. Some improvement is made is through the flue gas heat control mechanism in compact distillator using gate valve, at low, medium, and high speed engine. Compact distillator used is kind of a batch distillation column. Column design process using the shortcut method, then carried the tray design to determine the overall geometry. The distillation is done by comparing the separator with a tray of different distances. As well as by varying the volume of the feed and ethanol levels that will feed distilled. In this study, we analyzed the mixing of ethanol through variation between main jet and pilot jet in the carburetor separately interchangeably with gasoline. And finally mixing mechanism bio ethanol with gasoline improved with fuel mixer for performance.

Potential Health Risk of Herbal Distillates and Decoctions Consumption in Shiraz, Iran.

Science.gov (United States)

Moore, F; Akhbarizadeh, R; Keshavarzi, B; Tavakoli, F

2015-10-01

Concentration of 26 elements in 16 different herbal distillates and 5 herbal decoctions, were determined using inductively coupled plasma-mass spectrometry (ICP-MS). The elemental content of five raw herbal materials used for making decoctions and seven distilled and boiled residues were also evaluated by inductively coupled plasma optical emission spectrometry (ICP-OES). The results indicated that herbal products display a wide range of elemental concentrations. Compared with world health regulations, the concentrations of the elements in herbal distillates and decoctions did not exceed the recommended limits. The analysis of herbal extracts did not show a significant transfer of toxic elements during decoction preparation. Comparison of elemental content among fresh herbal material and herbal distillate and decoction of the same herb showed that, besides the elemental abundance of herbal organs, the ionic potential of elements also play an important role in elemental content of herbal products. Based on the results of the research, it seems that most health benefits attributed to herbal products (especially herbal distillates) are more related to their organic compounds rather than elemental composition. Calculated hazard quotient (HQ) and hazard index (HI) were used to evaluate the noncarcinogenic health risk from individual and combined metals via daily consumption of 100 ml of herbal distillates and 250 ml of herbal decoctions. Both HQs and HI through consumption of herbal distillates and herbal decoctions (except Valerian) were below 1. Apparently, daily consumption of herbal distillates and decoctions at the indicated doses poses no significant health risk to a normal adult.

Phase behaviour of heavy petroleum fractions in pure propane and n-butane and with methanol as co-solvent

International Nuclear Information System (INIS)

Canziani, D.; Ndiaye, P.M.; Franceschi, Elton; Corazza, Marcos L.; Vladimir Oliveira, J.

2009-01-01

This work reports phase equilibrium experimental results for heavy petroleum fractions in pure propane and n-butane as primary solvents and using methanol as co-solvent. Three kinds of oils were investigated from Marlim petroleum: a relatively light fraction coming from the first distillation of crude petroleum at atmospheric pressure (GOP - heavy gas oil of petroleum), the residue of such distillation (RAT) and the crude petroleum sample. Phase equilibrium measurements were performed in a high-pressure, variable-volume view cell, following the static synthetic method, over the temperature range of 323 K to 393 K, pressures up to 10 MPa and overall compositions of heavy component varying from 1 wt% to 40 wt%. Transition pressures for low methanol and oil concentrations were very close for GOP, RAT, and crude Marlim when using propane as the primary solvent. Close to propane critical temperature, two and three-phase transitions were observed for GOP and Marlim when methanol was increased. When n-butane was used as primary solvent, all transitions observed were of (vapour + liquid) type with transition pressure values smaller than those obtained for propane.

Retorts for distilling carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Lutz, H E

1921-09-12

A retort for distilling carbonaceous material is described in which a mass of such material is retained in a pocket formed between an outer wall and an internal wall which is perforated to permit the free escape of distilled products, the retorts having heating means that directly heat the retort but are so related to the pocket that the material therein is heated indirectly and simultaneously from all sides entirely by heat conducted thereto by the walls.

Three methods to distill multipartite entanglement over bipartite noisy channels

International Nuclear Information System (INIS)

Lee, Soojoon; Park, Jungjoon

2008-01-01

We first assume that there are only bipartite noisy qubit channels in a given multipartite system, and present three methods to distill the general Greenberger-Horne-Zeilinger state. By investigating the methods, we show that multipartite entanglement distillation by bipartite entanglement distillation has higher yield than ones in the previous multipartite entanglement distillations

Impact of Grape Varieties on Wine Distillates Flavour

Directory of Open Access Journals (Sweden)

Mara Banović

2002-01-01

Full Text Available Aroma is a phenomenon that occurrs when food and live organism mutually react during the process of consumption. Many factors influence the making of aroma of wine distillates (e.g. cognac during the technological process of distillation. It is extremely difficult to bring an objective judgement on the influence of individual factors since aroma is very subjective in its nature. The possibility of objective assessment of the influence of grape varieties on wine distillate was performed in this work using a computer in processing the results of cromatographic analyses of aroma substances. The given results were verified by sensor analyses. The achieved results have shown that mathematical model for calculating aroma chromatogram similarity can be successfully used for objective assessment of the influence of individual factors on aroma of wine distillates and that grape varieties have significant impact on aroma and the quality of wine distillates.

Source book for planning nuclear dual-purpose electric/distillation desalination plants

International Nuclear Information System (INIS)

Reed, S.A.

1981-02-01

A source book on nuclear dual-purpose electric/distillation desalination plants was prepared to assist government and other planners in preparing broad evaluations of proposed applications of dual-purpose plants. The document is divided into five major sections. Section 1 presents general discussions relating to the benefits of dual-purpose plants, and spectrum for water-to-power ratios. Section 2 presents information on commercial nuclear plants manufactured by US manufacturers. Section 3 gives information on distillation desalting processes and equipment. Section 4 presents a discussion on feedwater pretreatment and scale control. Section 5 deals with methods for coupling the distillation and electrical generating plants to operate in the dual mode

Source book for planning nuclear dual-purpose electric/distillation desalination plants

Energy Technology Data Exchange (ETDEWEB)

Reed, S.A.

1981-02-01

A source book on nuclear dual-purpose electric/distillation desalination plants was prepared to assist government and other planners in preparing broad evaluations of proposed applications of dual-purpose plants. The document is divided into five major sections. Section 1 presents general discussions relating to the benefits of dual-purpose plants, and spectrum for water-to-power ratios. Section 2 presents information on commercial nuclear plants manufactured by US manufacturers. Section 3 gives information on distillation desalting processes and equipment. Section 4 presents a discussion on feedwater pretreatment and scale control. Section 5 deals with methods for coupling the distillation and electrical generating plants to operate in the dual mode.

Laboratory sol-gel preparation of fine fraction of sintered uranium dioxide spheres

International Nuclear Information System (INIS)

Landspersky, H.; Tympl, M.

1984-01-01

The results are summed up of the laboratory investigation of preparing the fine fraction of sintered uranium dioxide particles from uranyl gel using the method of the mixed reactor and the method of the dual-liquid nozzle, processed by leaching, drying, calcination and sintering. None of the two methods provides monodispersion particles under the given conditions but better control of the throughflow of the liquid media may improve results. Leaching of the fine fraction is very quick and the leaching of most components takes no longer than 5 minutes. In view of the fact that leaching of all components does not proceed at the same rate it is recommended that leaching time be doubled, or that leaching take place in two stages. Azeotropic distillation with chlorinated hydrocarbons is a favourable procedure for obtaining quality material; it is, however, necessary to prevent dried particles from comino. into contact with the water phase condensing on the walls of the distillation vessel and running down onto the surface of the distilling mixture. Calcination at a temperature of 500 degC in a thin layer and sintering at temperatures between 1350 and 1550 degC at an adequate rate of inflow of gaseous media and adequate rate of outflow of reaction wastes results in the production of high quality material whose density exceeds 97 to 98% theoretical density. (author)

Energy consumption maps for quaternary distillation sequences

DEFF Research Database (Denmark)

Gomez-Castro, F.I.; Ramírez-Vallejo, N.E.; Segovia-Hernandez, J.G.

2016-01-01

Thermally coupled distillation columns represent a very interesting option for the intensification of distillation systems in order to reduce the energy consumption, and, as a consequence, the environmental impact of the separation process. Several thermally coupled distillation schemes can......, for a given mixture, depends on the nature of the mixture, usually quantified for ternary mixtures through the ease of separation index (ESI), and also on the feed composition. As can be noticed, the size of the design and optimization problem increases when these variables are considered in the generation...

Surface tension and wetting properties of rapeseed oil to biofuel conversion by-products

Science.gov (United States)

Muszyński, Siemowit; Sujak, Agnieszka; Stępniewski, Andrzej; Kornarzyński, Krzysztof; Ejtel, Marta; Kowal, Natalia; Tomczyk-Warunek, Agnieszka; Szcześniak, Emil; Tomczyńska-Mleko, Marta; Mleko, Stanisław

2018-04-01

This work presents a study on the surface tension, density and wetting behaviour of distilled glycerol, technical grade glycerol and the matter organic non-glycerin fraction. The research was conducted to expand the knowledge about the physical properties of wastes from the rapeseed oil biofuel production. The results show that the densities of technical grade glycerol (1.300 g cm-3) and distilled glycerol (1.267 g cm-3) did not differ and were significantly lower than the density of the matter organic non-glycerin fraction (1.579 g cm-3). Furthermore, the surface tension of distilled glycerol (49.6 mN m-1) was significantly higher than the matter organic non-glycerin fraction (32.7 mN m-1) and technical grade glycerol (29.5 mN m-1). As a result, both technical grade glycerol and the matter organic non-glycerin fraction had lower contact angles than distilled glycerol. The examined physical properties of distilled glycerol were found to be very close to that of the commercially available pure glycerol. The results suggest that technical grade glycerol may have potential application in the production of glycerol/fuel blends or biosurfactants. The presented results indicate that surface tension measurements are more useful when examining the quality of biofuel wastes than is density determination, as they allow for a more accurate analysis of the effects of impurities on the physical properties of the biofuel by-products.

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Byrom, W A; Bennett, J A.B.

1884-02-22

Effecting the separation of the various products of the distillation of coal, shale, etc., by taking advantage of the graduated temperature of successive portions of the length of mechanical retorts is described. The substances entering from the hopper are gradually heated in their progress and give off a series of products in their order of volatilization, which pass from openings in the retort through a series of ascension pipes into collecting-vessels. The vessels are designed to contain different portions of the distillate and are sealed against the escape of uncondensed vapor or gas by the condensed liquid. Each of the ascension pipes communicates above its vessel with a common pipe to convey away permanent gases. The flues for heating the retort may be so arranged as to give the greatest heat at the end farthest from the point of entrance, or the stages of heat may be self-regulated by the time necessary for the material to acquire heat as it travels. If necessary the pipes may be fitted with refrigerating-appliances.

Development of High Throughput Salt Separation System with Integrated Liquid Salt Separation - Salt Distillation Assembly

Energy Technology Data Exchange (ETDEWEB)

Kwon, Sangwoon; Park, K. M.; Kim, J. G.; Jeong, J. H.; Lee, S. J.; Park, S. B.; Kim, S. S.

2013-01-15

The capacity of a salt distiller should be sufficiently large to reach the throughput of uranium electro-refining process. In this study, an assembly composing a liquid separation sieve and a distillation crucible was developed for the sequential operation of a liquid salt separation and a vacuum distillation in the same tower. The feasibility of the sequential salt separation was examined by the rotation test of the sieve-crucible assembly and sequential operation of a liquid salt separation and a vacuum distillation. The adhered salt in the uranium deposits was removed successfully. The salt content in the deposits was below 0.1 wt% after the sequential operation of the liquid salt separation - salt distillation. From the results of this study, it could be concluded that efficient salt separation can be realized by the sequential operation of liquid salt separation and vacuum distillation in one distillation tower since the operation procedures are simplified and no extra operation of cooling and reheating is necessary.

Cascade Distillation Subsystem Development: Progress Toward a Distillation Comparison Test

Science.gov (United States)

Callahan, M. R.; Lubman, A.; Pickering, Karen D.

2009-01-01

Recovery of potable water from wastewater is essential for the success of long-duration manned missions to the Moon and Mars. Honeywell International and a team from NASA Johnson Space Center (JSC) are developing a wastewater processing subsystem that is based on centrifugal vacuum distillation. The wastewater processor, referred to as the Cascade Distillation Subsystem (CDS), utilizes an innovative and efficient multistage thermodynamic process to produce purified water. The rotary centrifugal design of the system also provides gas/liquid phase separation and liquid transport under microgravity conditions. A five-stage subsystem unit has been designed, built, delivered and integrated into the NASA JSC Advanced Water Recovery Systems Development Facility for performance testing. A major test objective of the project is to demonstrate the advancement of the CDS technology from the breadboard level to a subsystem level unit. An initial round of CDS performance testing was completed in fiscal year (FY) 2008. Based on FY08 testing, the system is now in development to support an Exploration Life Support (ELS) Project distillation comparison test expected to begin in early 2009. As part of the project objectives planned for FY09, the system will be reconfigured to support the ELS comparison test. The CDS will then be challenged with a series of human-gene-rated waste streams representative of those anticipated for a lunar outpost. This paper provides a description of the CDS technology, a status of the current project activities, and data on the system s performance to date.

Transport phenomena and fouling in vacuum enhanced direct contact membrane distillation: Experimental and modelling

KAUST Repository

Naidu, Gayathri

2016-08-27

The application of vacuum to direct contact membrane distillation (vacuum enhanced direct contact membrane distillation, V-DCMD) removed condensable gasses and reduced partial pressure in the membrane pores, achieving 37.6% higher flux than DCMD at the same feed temperature. Transfer mechanism and temperature distribution profile in V-DCMD were studied. The empirical flux decline (EFD) model represented fouling profiles of V-DCMD. In a continuous V-DCMD operation with moderate temperature (55 degrees C) and permeate pressure (300 mbar) for treating wastewater ROC, a flux of 16.0 +/- 0.3 L/m(2) h and high quality distillate were achieved with water flushing, showing the suitability of V-DCMD for ROC treatment. (C) 2016 Elsevier B.V. All rights reserved.

Transport phenomena and fouling in vacuum enhanced direct contact membrane distillation: Experimental and modelling

KAUST Repository

Naidu, Gayathri; Shim, Wang Geun; Jeong, Sanghyun; Choi, YoungKwon; Ghaffour, NorEddine; Vigneswaran, Saravanamuthu

2016-01-01

The application of vacuum to direct contact membrane distillation (vacuum enhanced direct contact membrane distillation, V-DCMD) removed condensable gasses and reduced partial pressure in the membrane pores, achieving 37.6% higher flux than DCMD at the same feed temperature. Transfer mechanism and temperature distribution profile in V-DCMD were studied. The empirical flux decline (EFD) model represented fouling profiles of V-DCMD. In a continuous V-DCMD operation with moderate temperature (55 degrees C) and permeate pressure (300 mbar) for treating wastewater ROC, a flux of 16.0 +/- 0.3 L/m(2) h and high quality distillate were achieved with water flushing, showing the suitability of V-DCMD for ROC treatment. (C) 2016 Elsevier B.V. All rights reserved.

A comparative evaluation of nitrogen compounds in petroleum distillates

Energy Technology Data Exchange (ETDEWEB)

Singh, Dheer; Chopra, Anju; Patel, Mitra Bhanu; Sarpal, Amarjit Singh [Indian Oil Corporation Limited, Faridabad (India). Research and Development Centre

2011-07-15

Although the concentration of nitrogen compounds in crude oil is relatively low, they can become more concentrated in petroleum distillates and poison the catalysts used in refining processes. They cause undesirable deposits, color formation and odor in products; they also contribute to air pollution and some are highly carcinogenic. The poisoned catalyst becomes deactivated for hydrodesulfurization and unable to remove sulfur from middle distillates. In order to understand the effect on catalytic processes, it is desirable to identify the nitrogen compounds in various petroleum distillates. This paper compares the nitrogen species profiles in different petroleum distillates using a nitrogen chemiluminescence detector. In addition, four different petroleum distillate samples from different refineries were analyzed to find the variation in their nitrogen profiles. The nitrogen compounds in petroleum distillate samples were identified as anilines, quinolines, indoles, and carbazoles and their alkyl derivatives. Quantitation was carried out against known reference standards. The quantitative data were compared to the total nitrogen content determined by elemental analysis. (orig.)

Fractional Multistage Hydrothermal Liquefaction of Biomass and Catalytic Conversion into Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Cortright, Randy [Virent, Inc., Madison, WI (United States); Rozmiarek, Robert [Virent, Inc., Madison, WI (United States); Dally, Brice [Virent, Inc., Madison, WI (United States); Holland, Chris [Virent, Inc., Madison, WI (United States)

2017-08-31

The objective of this project was to develop an improved multistage process for the hydrothermal liquefaction (HTL) of biomass to serve as a new front-end, deconstruction process ideally suited to feed Virent’s well-proven catalytic technology, which is already being scaled up. This process produced water soluble, partially de-oxygenated intermediates that are ideally suited for catalytic finishing to fungible distillate hydrocarbons. Through this project, Virent, with its partners, demonstrated the conversion of pine wood chips to drop-in hydrocarbon distillate fuels using a multi-stage fractional conversion system that is integrated with Virent’s BioForming® process. The majority of work was in the liquefaction task and included temperature scoping, solvent optimization, and separations.

Crude oil and its’ distillation: an experimental approach in High School using conceptual maps

Directory of Open Access Journals (Sweden)

Dionísio Borsato

2006-02-01

Full Text Available Conceptual maps are representations of ideas organized in the form of bidimensional diagrams. In the present work the theme of oil fractional distillation was explored, and the conceptual maps were elaborated both before and after the activities by 43 students from the 1st and 3rd High School grades of a public school in Londrina – PR. The study was conducted theoretically and in practice, with a daily life approach. The use of the motivational theme and the opening text as previous organizers, enabled the establishment of a cognitive link between the students’ previous knowledge and the new concepts. Differences between the maps were verified before and after the activities as well as among the work groups. The students, stimulated by the technique, created better structured maps.

Development of an Exploration-Class Cascade Distillation Subsystem: Performance Testing of the Generation 1.0 Prototype

Science.gov (United States)

Callahan, Michael R.; Sargusingh, Miriam J.

2015-01-01

The ability to recover and purify water is crucial for realizing long-term human space missions. The National Aeronautics and Space Admininstration and Honeywell co-developed a five-stage vacuum rotary distillation water recovery system referred to as the Cascade Distillation Subsystem (CDS). Over the past three years, NASA's Advanced Exploration Systems (AES) Water Recovery Project (WRP) has been working toward the development of a flight-forward CDS design. In 2012 the original CDS prototype underwent a series of incremental upgrades and tests intened to both demonstrate the feasibility of a on-orbit demonstration of the system and to collect operational and performance data to be used to inform a second generation design. The latest testing of the CDS Generation 1.0 prototype was conducted May 29 through July 2, 2014. Initial system performance was benchmarked by processing deionized water and sodium chloride. Following, the system was challenged with analogue urine waste stream solutions stabilized with an Oxone-based and the two International Space Station baseline and alternative pretreatment solutions. During testing, the system processed more than 160 kilograms of wastewater with targeted water recoveries between 75 and 85% depending on the specific waste stream tested. For all wastewater streams, contaminant removals from wastewater feed to product water distillate, were estimated at greater than 99%. The average specific energy of the system was less than 120 Watt-hours/kilogram. The following paper provides detailed information and data on the performance of the CDS as challenged per the WRP test objectives.

Asymptotic speedups, bisimulation and distillation (Work in progress)

DEFF Research Database (Denmark)

Jones, Neil; Hamilton, G. W.

2015-01-01

Distillation is a fully automatic program transformation that can yield superlinear program speedups. Bisimulation is a key to the proof that distillation is correct, i.e., preserves semantics. However the proof, based on observational equivalence, is insensitive to program running times....... This paper shows how distillation can give superlinear speedups on some “old chestnut” programs well-known from the early program transformation literature: naive reverse, factorial sum, and Fibonacci....

MEASUREMENT OF THE B0 ---> D*- A+(1) BRANCHING FRACTION WITH PARTIALLY RECONSTRUCTED D*

Energy Technology Data Exchange (ETDEWEB)

Salvatore, Pasquale F

2002-07-26

The B{sup 0} {yields} D*{sup -} a{sub 1}{sup +} branching fraction has been measured with data collected by the BaBar experiment in 1999 and 2000 corresponding to a total integrated luminosity of 20.6 fb{sup -1}. Signal events have been selected using a partial reconstruction technique, in which only the a{sub 1}{sup +} and the slow pion ({pi}{sub s}) from the D*{sup -} decay are identified. A signal yield of 18400 {+-} 1200 events has been found, corresponding to a preliminary branching fraction of (1.20 {+-} 0.07(stat) {+-} 0.14(syst))%.

Refreshment topics II: Design of distillation columns

Directory of Open Access Journals (Sweden)

Milojević Svetomir

2006-01-01

Full Text Available For distillation column design it is necessary to define all the variable parameters such as component concentrations in different streams temperatures, pressures, mass and energy flow, which are used to represent the separation process of some specific system. They are related to each other according to specific laws, and if the number of such parameters exceeds the number of their relationships, in order to solve a problem some of them must be specified in advance or some constraints assumed for the mass balance, the balance of energy, phase equilibria or chemical equilibria. Knowledge of specific elements which are the constituents of a distillation unit must be known to define the number of design parameters as well as some additional apparati also necessary to realize the distilation. Each separate apparatus might be designed and constructed only if all the necessary and variable parameters for such a unit are defined. This is the right route to solve a distilation unit in many different cases. The construction of some distillation unit requires very good knowledge of mass, heat and momentum transfer phenomena. Moreover, the designer needs to know which kind of apparatus will be used in the distillation unit to realize a specific production process. The most complicated apparatus in a rectification unit is the distillation column. Depending on the complexity of the separation process one, two or more columns are often used. Additional equipment are heat exchangers (reboilers, condensers, cooling systems, heaters, separators, tanks for reflux distribution, tanks and pumps for feed transportation, etc. Such equipment is connected by pipes and valves, and for the normal operation of a distillation unit other instruments for measuring the flow rate, temperature and pressure are also required. Problems which might arise during the determination and selection of such apparati and their number requires knowledge of the specific systems which must

Effect of process distillation on mutagenicity and cell-transformation activity of solvent-refined, coal-derived liquids

Energy Technology Data Exchange (ETDEWEB)

Pelroy, R.A.; Frazier, M.E.; Later, D.W.; Wright, C.W.; Wilson, B.W.

1985-05-01

Blended SRC-II process streams, representing a full boiling range distillate material, were fractionally distilled into non-overlapping 50 F cuts with bp between 300 and 850 C and another set with bp ranging between 138 and 1055 F. Distillate cuts were assayed for mutagenic activity using the histidine reversion assay with Salmonella typhimurium strains TA98, TA100, TA1535 and TA1537, as well as for mammalian-cell transformation (mct) activity in the Syrian hamster embryo test, and DNA damage in the prophage induction assay (pia). Samples were also separated into chemical class fractions by alumina column chromatography and analysed by high resolution gas chromatography. In the met and microbial mutagenicity assays, significant activity was found almost exclusively in cuts with bp> above 700 F, with the highest activity in the mct assay observed for cuts above 800 F. All of the cuts showed increased levels of DNA damage as expressed by lambda pia in Escherichia coli 8177. However, the greatest activity was associated with cuts with bp in the 800 F+ range. Chemical analysis of the 50 F cuts showed a variety of polycyclic aromatic hydrocarbons (PAH) and amino-PAH compounds to be present in the cuts with bp> above 700 F and essentially absent from cuts with bp< 700 F. The sample set of non-overlapping (50 F) cuts were reblended according to the proportions of each cut found in the original blend material. These reblended composites were then assayed to compare their activity with that predicted from the activities of the component cuts. The results indicated the microbial mutagenicity response was essentially additive. Met activities were non-additive, indicating a compositional effect on the expression of transforming agents in the complex mixture. 18 references.

Fundamental Study on a Distillation Separation of a LiCl-KCl Eutectic Salt from Rare Earth Precipitates

International Nuclear Information System (INIS)

Yang, Hee Chul; Eun, Hee Chul; Kim, In Tae

2010-01-01

The distillation rate on LiCl-KCl eutectic salt under different vacuums from 0.5-50 mmHg was first investigated by using both a non-isothermal and a isothermal thermogravimetric (TG) analysis. Based on the non-isothermal TG data, distillation rate equations as a function of the temperature could be derived. Calculated flux by these model flux equations was in agreement with the distillation rate obtained from isothermal TG analysis. A distillation rate of 10 -4 -10 -5 mole cm -2 sec -1 is obtainable at temperatures less than 1300 K and vacuums of 0.5-50 mmHg. About a 99% salt distillation efficiency was obtained after an hour at a temperature above 1150 K under 50 mmHg in a small scale distillation test system. An increase in the vaporizing surface area is relatively effective for removing residual salt in the remaining particles, when compared to that for the vaporizing time. Over 99.95% of total distillation efficiency was obtained for a 1-h distillation operation by increasing the inner surface area from 4.52 cm 2 to 12.56 cm 2 .

27 CFR 26.40 - Marking containers of distilled spirits.

Science.gov (United States)

2010-04-01

... spirits. The distiller, rectifier, or bottler shall serially number each case, barrel, cask, or similar... the container, the distiller, rectifier, or bottler shall plainly print, stamp, or stencil with... barrel, cask or similar container or on one side of each case, as follows: (a) The name of the distiller...

Distillation modeling for a uranium refining process

International Nuclear Information System (INIS)

Westphal, B.R.

1996-01-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed open-quotes cathode processingclose quotes. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process

Distillation modeling for a uranium refining process

Energy Technology Data Exchange (ETDEWEB)

Westphal, B.R.

1996-03-01

As part of the spent fuel treatment program at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, containing a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a simple batch operation and is termed {open_quotes}cathode processing{close_quotes}. The incremental distillation of electrolyte salt will be modeled by an equilibrium expression and on a molecular basis since the operation is conducted under moderate vacuum conditions. As processing continues, the two models will be compared and analyzed for correlation with actual operating results. Possible factors that may contribute to aberrations from the models include impurities at the vapor-liquid boundary, distillate reflux, anomalous pressure gradients, and mass transport phenomena at the evaporating surface. Ultimately, the purpose of either process model is to enable the parametric optimization of the process.

Study on Salting out-Steam Distillation Extraction Technology and Antibacterial Activities of Essential Oil from Cumin Seeds

Directory of Open Access Journals (Sweden)

Hong Zhang

2014-11-01

Full Text Available The effects of different factors on the yield of essential oil from were discussed, and the extraction conditions of essential oil from cumin seeds by salting out-steam distillation technology based on single-factor test and orthogonal experiment, as well as its antibacterial activities on several common food spoilage bacteria were studied in this paper. The results showed that, the impact order of the influence factors was liquid/solid ratio > distilling time > NaCl concentration, and optimized extraction conditions were as follows, liquid to material ratio 15:1, soaking time 1 h, 4% NaCl, steam distilling time 3 h. The yield of essential oil was up to 4.48% under these conditions. The results of antibacterial activity assays showed that the essential oil from cumin seeds exhibited the different antibacterial activities against some food borne pathogens, especially it presented the best inhibitory effect against Bacillus subtilis with the minimum inhibitory concentration (MIC and minimum bactericidal concentration (MBC values of 6.25 and 12.5 mg/mL respectively, followed by Staphylococcus albus and Staphylococcus aureus, the lowest for Pseudomonas aeruginosa and Shigella dysenteriae

Deuterium fractionation mechanisms in interstellar clouds

International Nuclear Information System (INIS)

Dalgarno, A.; Lepp, S.

1984-01-01

The theory of the fractionation of deuterated molecules is extended to include reactions with atomic deuterium. With the recognition that dissociative recombination of H + 3 is not rapid, observational data can be used in conjunction with the theory to derive upper and lower bounds to the cosmic deuterium-hydrogen abundance ratio. We find that [D]/[H] is at least 3.4 x 10 -6 and at most 4.0 x 10 -5 with a probable value of 1 x 10 -5 . Because of the reaction HCO + +D→DCO + +H, upper limits can be derived for the fractional ionization which depend only weakly on the cosmic ray flux, zeta. In four clouds, the upper limits to the fractional ionization lie between 1.1 x 10 -6 and 1.5 x 10 -6 if zeta = 10 -7 s -1 and between 3.1 x 10 -6 and 1.8 x 10 -6 if zeta = 10 -16 s -1

Chronic consumption of distilled sugarcane spirit induces anxiolytic-like effects in mice.

Science.gov (United States)

Sena, Maria Clecia P; Nunes, Fabíola C; Salvadori, Mirian G S Stiebbe; Carvalho, Cleyton Charles D; Morais, Liana Clebia S L; Braga, Valdir A

2011-01-01

Chronic ethanol consumption is a major public health problem throughout the world. We investigated the anxiolytic-like effects and the possible ever injury induced by the chronic consumption of ethanol or sugarcane spirit in mice. Adult mice were exposed to a two-bottle free-choice paradigm for 6 weeks. The mice in Group A (n = 16) had access to sugarcane spirit + distilled water, the mice in Group B (n = 15) had access to ethanol + distilled water, and the mice in Group C (control, n = 14) had access to distilled water + distilled water. The ethanol content in the beverages offered to Groups A and B was 2% for the first week, 5% for the second week and 10% for the remaining four weeks. At the end of the experimental period, the mice were evaluated using the elevated-plus maze and the hole-board test to assess their anxiety-related behaviors. We also determined the serum aspartate aminotransferase and alanine aminotransferase levels. In the elevated-plus maze, the time spent in the open arms was increased in the mice exposed to chronic ethanol (32 ± 8 vs. 7 ± 2 s, n = 9) or sugarcane spirit (36 ± 9 vs. 7 ± 2 s, n = 9) compared to the controls. In the hole-board test, the mice exposed to ethanol or sugarcane spirit displayed increases in their head-dipping frequency (16 ± 1 for the control group, 27 ± 2 for the ethanol group, and 31 ± 3 for the sugarcane-spirit group; n = 9 for each group). In addition, the mice exposed to sugarcane spirit displayed an increase in the aspartate aminotransferase / alanine aminotransferase ratio compared to the ethanol group (1.29 ± 0.17 for the control group and 2.67 ± 0.17 for the sugarcane spirit group; n = 8 for each group). The chronic consumption of sugarcane-spirit produces liver injury and anxiolytic-like effects and the possible liver injury in mice.

Chronic consumption of distilled sugarcane spirit induces anxiolytic-like effects in mice

Directory of Open Access Journals (Sweden)

Maria Clecia P. Sena

2011-01-01

Full Text Available OBJECTIVE: Chronic ethanol consumption is a major public health problem throughout the world. We investigated the anxiolytic-like effects and the possible ever injury induced by the chronic consumption of ethanol or sugarcane spirit in mice. METHOD: Adult mice were exposed to a two-bottle free-choice paradigm for 6 weeks. The mice in Group A (n = 16 had access to sugarcane spirit + distilled water, the mice in Group B (n = 15 had access to ethanol + distilled water, and the mice in Group C (control, n = 14 had access to distilled water + distilled water. The ethanol content in the beverages offered to Groups A and B was 2% for the first week, 5% for the second week and 10% for the remaining four weeks. At the end of the experimental period, the mice were evaluated using the elevated-plus maze and the hole-board test to assess their anxiety-related behaviors. We also determined the serum aspartate aminotransferase and alanine aminotransferase levels. RESULTS: In the elevated-plus maze, the time spent in the open arms was increased in the mice exposed to chronic ethanol (32 + 8 vs. 7 + 2 s, n = 9 or sugarcane spirit (36 + 9 vs. 7 + 2 s, n = 9 compared to the controls. In the hole-board test, the mice exposed to ethanol or sugarcane spirit displayed increases in their head-dipping frequency (16 + 1 for the control group, 27 + 2 for the ethanol group, and 31 + 3 for the sugarcane-spirit group; n = 9 for each group. In addition, the mice exposed to sugarcane spirit displayed an increase in the aspartate aminotransferase / alanine aminotransferase ratio compared to the ethanol group (1.29 + 0.17 for the control group and 2.67 + 0.17 for the sugarcane spirit group; n = 8 for each group. CONCLUSION: The chronic consumption of sugarcane-spirit produces liver injury and anxiolytic-like effects and the possible liver injury in mice.

Driving Force Based Design of Cyclic Distillation

DEFF Research Database (Denmark)

Nielsen, Rasmus Fjordbak; Huusom, Jakob Kjøbsted; Abildskov, Jens

2017-01-01

with mixed phase feeds. A range of binary test cases, benzene toluene, methanol water, and ethanol water, are evaluated. The advantage of the design approach in cyclic distillation is shown to be analogous to the advantages obtained in conventional continuous distillation, including a minimal utility...

Search for fractional charge

International Nuclear Information System (INIS)

Turner, R.E.

1984-01-01

A search was made for fractional charges of the form Z plus two-thirds e, where Z is an integer. It was assumed that the charges exist in natural form bound with other fractional charges in neutral molecules. It was further assumed that these neutral molecules are present in air. Two concentration schemes were employed. One sample was derived from the waste gases from a xenon distillation plant. This assumes that high mass, low vapor pressure components of air are concentrated along with the xenon. The second sample involved ionizing air, allowing a brief recombination period, and then collecting residual ions on the surface of titanium discs. Both samples were analyzed at the University of Rochester in a system using a tandem Van de Graff to accelerate particles through an essentially electrostatic beam handling system. The detector system employed both a Time of Flight and an energy-sensitive gas ionization detector. In the most sensitive mode of analysis, a gas absorber was inserted in the beam path to block the intense background. The presence of an absorber limited the search to highly penetrating particles. Effectively, this limited the search to particles with low Z and masses greater than roughly fifty GeV. The final sensitivities attained were on the order of 1 x 10 -20 for the ionized air sample and 1 x 10 -21 for the gas sample. A discussion of the caveats that could reduce the actual level of sensitivity is included

Vapor compression distiller and membrane technology for water revitalization

Science.gov (United States)

Ashida, A.; Mitani, K.; Ebara, K.; Kurokawa, H.; Sawada, I.; Kashiwagi, H.; Tsuji, T.; Hayashi, S.; Otsubo, K.; Nitta, K.

1987-01-01

Water revitalization for a space station can consist of membrane filtration processes and a distillation process. Water recycling equipment using membrane filtration processes was manufactured for ground testing. It was assembled using commercially available components. Two systems for the distillation are studied: one is absorption type thermopervaporation cell and the other is a vapor compression distiller. Absorption type thermopervaporation, able to easily produce condensed water under zero gravity, was investigated experimentally and through simulated calculation. The vapor compression distiller was studied experimentally and it offers significant energy savings for evaporation of water.

DESIGN, DEVELOPMENT AND TESTING OF MULTIEFFECT DISTILLER/EVAPORATOR USING SCHEFFLER SOLAR CONCENTRATORS

Directory of Open Access Journals (Sweden)

AJAY CHANDAK

2009-09-01

Full Text Available Authors designed and experimented with multistage evaporation system for production of distilled water. Two Scheffler concentrators of 16 sqm each were used for generating steam in the first stage at 8 bar pressure and the pressure is gradually brought down to 1 bar, in four stage distillation unit. Total yield obtained in the project was 2.3 times that of single stage distillation. Temperature drop in every subsequent stage was designed to 25 degree centigrade. Heat of condensation in the last stage and also sensible heat of the condensate in all the stages were used for preheating of water in the next batch. The system has great potential in food processing industry for applications of juice thickening, sauces, jams, salt concentrating systems and distilled water applications, desalination etc. Results of the project are very encouraging for commercial scale application.

Exergy Analysis of Air-Gap Membrane Distillation Systems for Water Purification Applications

Directory of Open Access Journals (Sweden)

Daniel Woldemariam

2017-03-01

Full Text Available Exergy analyses are essential tools for the performance evaluation of water desalination and other separation systems, including those featuring membrane distillation (MD. One of the challenges in the commercialization of MD technologies is its substantial heat demand, especially for large scale applications. Identifying such heat flows in the system plays a crucial role in pinpointing the heat loss and thermal integration potential by the help of exergy analysis. This study presents an exergetic evaluation of air-gap membrane distillation (AGMD systems at a laboratory and pilot scale. A series of experiments were conducted to obtain thermodynamic data for the water streams included in the calculations. Exergy efficiency and destruction for two different types of flat-plate AGMD were analyzed for a range of feed and coolant temperatures. The bench scale AGMD system incorporating condensation plate with more favorable heat conductivity contributed to improved performance parameters including permeate flux, specific heat demand, and exergy efficiency. For both types of AGMD systems, the contributions of the major components involved in exergy destruction were identified. The result suggested that the MD modules caused the highest fraction of destructions followed by re-concentrating tanks.

A Modelling Framework for Conventional and Heat Integrated Distillation Columns

DEFF Research Database (Denmark)

Bisgaard, Thomas; Huusom, Jakob Kjøbsted; Abildskov, Jens

2013-01-01

of hydrocarbons such as separations of equimolar mixtures of benzene/toluene or propane/propene described by simple models, a generic, modular, model framework is presented in this work. At present, the framework is able to describe a conventional distillation column, a mechanical vapor recompression column......Diabatic operation of distillation columns can lead to signicant reductions in energy utilization and operation cost compared to conventional (adiabatic) distillation columns, at an expense of an increased complexity of design and operation. The earliest diabatic distillation conguration dates back...... to the late 70s, and various dierent congurations have appeared since. However, at present, no full-scale diabatic distillation columns are currently operating in the industry. Current studies related to alternative distillation congurations report very dierent gures for potential energy savings which...

Energy saving in crude oil atmospheric distillation columns by modifying the vapor feed inlet tray

Energy Technology Data Exchange (ETDEWEB)

Arjmand, M. [Royal Institute of Technology (KTH), Graduate School of Chemical Engineering, Stockholm (Sweden); Moreno, L.; Liu, L. [Royal Institute of Technology (KTH), Department of Chemical Engineering and Technology, Stockholm (Sweden)

2011-08-15

Optimization of a typical crude oil atmospheric distillation unit and reduction of energy conservation were carried out through modifying the implementation and change in the flash zone of the tower. A conventional procedure in such units involves the combination of liquid and vapor product of the prefractionation train surge drum upon introduction to the tower. However, it is theoretically illustrated and represented by simulation means that introducing the vapor feed into the upper stages of the distillation column separately can lead to an energy saving of 12.6 % in the condenser duty, an increased liquid-to-gas flow (L/G) at certain points of the column, and hence to a reduction in diameter and investment costs of new tower designs of approximately US$ 0.7 million a{sup -1}. The proposal can be put into practice without the need of additional equipments or additional cost of difficult rerouting the streams. An industrial case study of a steady-state crude oil distillation unit is given by simulation provision of AspenHysys trademark. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The separation of benzene and cyclohexane by the batch extractive distillation

International Nuclear Information System (INIS)

Zhang Weijiang; Gui Xia

2006-01-01

The separation of the mixture is very important in environmental protection engineering and productive department. Azeotropic liquid mixture can not be separated by conventional distillation. But extractive distillation or combination of the two can be valid for them. In this paper, an experiment to separate benzene and Cyclohexane by batch extractive distillation was carried out with N,N-dimethylformide (DMF), dimethyl sulfoxide (DMSO) and their mixture as extractive solvent in this paper. The effect of operation parameter such as solvent flow rate and Reflux ratio on the separation was studied in the same operating condition. The results showed that the separation effect was improved with the increase of solvent flow rate and the Reflux ratio. All the three extractive solvent can separate benzene and cyclohexane to some extent, But the best was N,N- dimethylformide (DMF), the next was the mixture, and the last was dimethyl sulfoxide (DMSO). In the experiment the best operation condition was with N,N-dimethylformide(DMF) as extractive solvent, the solvent flow rate being 12.33ml/min, the Reflux ratio being 6. (authors)

Transient behavior of enrichment of tritium water in adsorption-distillation column

International Nuclear Information System (INIS)

Fukada, Satoshi

2006-01-01

Enrichment of tritium in an adsorption-distillation column was experimentally investigated under the two processes of simple distillation and total-reflux distillation. Adsorption of water on silica-gel pellets enhanced the total isotope separation factor in the water distillation column. The transient behavior of tritium enrichment was analyzed using material balance equations of tritium and water in each cell with a height corresponding to HETP. The experimental transient behavior was well simulated by the material balance equations with additional assumptions on vapor and liquid flow rates regardless of the different processes of simple distillation and total-reflux distillation. (author)

Process and apparatus to distil petroleum. Verfahren und Vorrichtung zur Erdoel-Destillation

Energy Technology Data Exchange (ETDEWEB)

Buchenau, R.; Fauser, F.; Fischer, W.

1982-12-23

In a process to distil petroleum the raw petroleum is distilled in the first instance at atmospheric pressure to separate the low-boiling components and subsequently under vacuum to separate the remaining components. The vacuum distillation is carried out as a flash distillation using a shortway distiller.

Fractional nonablative 1,540-nm laser resurfacing of atrophic acne scars. A randomized controlled trial with blinded response evaluation

DEFF Research Database (Denmark)

Hedelund, Lene; Moreau, Karen Estell R; Beyer, Ditte M

2010-01-01

The efficacy of nonablative fractional laser resurfacing of acne scars has been described in case reports and uncontrolled trials. The present study is the first randomized controlled trial in this field. The aim of this study was to examine the efficacy and adverse effects of 1,540-nm nonablative...... fractional laser treatment of acne scars. Ten patients with acne scars were included. Two intraindividual areas of similar size and appearance within contralateral anatomical regions were randomized to (1) 3-monthly laser treatments with a StarLux 1,540-nm fractional handpiece, and (2) no treatment. Blinded...... appeared more even and smooth than untreated control areas (4.5, 2-6.5, versus 6.5, 4.5-8, P=0.0156, at 4 weeks; 4.5, 2.5-6.5, versus 6.5, 4.5-8, at 12 weeks; P=0.0313). Patients were satisfied with the treatment (5.5, 1-7, after 12 weeks) and five of the ten patients evaluated their acne scars...

Development of a sealed source radiation detector system for gamma ray scanning of petroleum distillation columns

International Nuclear Information System (INIS)

Vasquez Salvador, Pablo Antonio

2004-01-01

Gamma Ray Scanning is an online technique to 'view' the hydraulic performance of an operating column, with no disruption to operating processes conditions (pressure and temperature), as a cost-effective solution. The principle of this methodology consists of a small suitably sealed gamma radiation source and a radiation detector experimentally positioned to the column, moving concurrently in small increments on opposite sides and the quantity of gamma transmitted. The source-detector system consists of: a sealed ''6 0 Co radioactive source in a panoramic lead radiator, a scintillator detector coupled to a ratemeter / analyzer and a mobile system. In this work, a gamma scanning sealed source-detector system for distillation columns, was developed, comparing two scintillator detectors: NaI(Tl) (commercial) and CsI(Tl) (IPEN). In order to project the system, a simulated model of a tray-type distillation column was used. The equipment developed was tested in an industrial column for water treatment (6.5 m diameter and 40 m height). The required activities of 6 ''0Co, laboratory (11.1 MBq) and industrial works (1.48 TBq) were calculated by simulation software. Both, the NaI(Tl) and the CsI(Tl) detectors showed good proprieties for gamma scanning applications, determining the position and presence or absence of trays. (author)

Numerical simulation of solar-assisted multi-effect distillation (SMED) desalination systems

KAUST Repository

Kim, Youngdeuk

2013-01-01

We present a simulation model for the transient behavior of solar-assisted seawater desalination plant that employs the evacuated-tube collectors in conjunction with a multieffect distillation plant of nominal water production capacity of 16m3/day. This configuration has been selected due to merits in terms of environment-friendliness and energy efficiency. The solar-assisted multi-effect distillation system comprises 849 m2 of evacuated-tube collectors, 280 m3 water storage tanks, auxiliary heater, and six effects and a condenser. The present analysis employs a baseline configuration, namely; (i) the local solar insolation input (Jeddah, Saudi Arabia), (ii) a coolant flow rate through the headers of collector based on ASHRAE standards, (iii) a heating water demand, and (iv) the augmentation of water temperature by auxiliary when the supply temperature from the solar tank drops below the set point. It is observed that the annual collector efficiency and solar fraction decrease from 57.3 to 54.8% and from 49.4 to 36.7%, respectively, with an increase in the heating water temperature from 80 to 90 °C. The overall water production rate and the performance ratio increase slightly from 0.18 to 0.21 kg/s and from 4.11 to 4.13, respectively. © 2013 Desalination Publications.

Teaching and learning distillation in chemistry laboratory courses

Science.gov (United States)

van Keulen, Hanno; Mulder, Theo H. M.; Goedhart, Martin J.; Verdonk, Adri H.

This study investigates the problems chemistry majors have with learning distillation in traditional chemistry laboratory courses. Using an interpretive cyclic research design, we collected and interpreted data, mainly in the form of observation notes and transcriptions of the discourse that takes place during laboratory courses. It was found that students experience numerous problems; these are described and interpreted. We summarize students' problems in four categories: (a) students use an independent component conception; (b) they have insufficient understanding of the properties of vapor; (c) they regard distillation from a physical point of view; and (d) they do not have a practical understanding of thermodynamics. The main origin of these problems was found to lie with the traditional curriculum structure. Lecture courses and textbooks treat distillation in a generalized and decontextualized way, whereas decisions in actual distillations are always based on contextual features. It was found that textbooks and teachers often do not discriminate carefully and explicitly among five different contexts for distillation: organic synthesis, chemical analysis, analytical chemistry, physical chemistry, and preparation of products. Students take the generalized concepts at face value and apply them to all distillations regardless of context. They cannot interpret their observations or make reasoned decisions based on the theoretical framework of a specific context.Received: 2 May 1994; Revised: 14 December 1994;

Sample distillation/graphitization system for carbon pool analysis by accelerator mass spectrometry (AMS)

International Nuclear Information System (INIS)

Pohlman, J.W.; Knies, D.L.; Grabowski, K.S.; DeTurck, T.M.; Treacy, D.J.; Coffin, R.B.

2000-01-01

A facility at the Naval Research Laboratory (NRL), Washington, DC, has been developed to extract, trap, cryogenically distill and graphitize carbon from a suite of organic and inorganic carbon pools for analysis by accelerator mass spectrometry (AMS). The system was developed to investigate carbon pools associated with the formation and stability of methane hydrates. However, since the carbon compounds found in hydrate fields are ubiquitous in aquatic ecosystems, this apparatus is applicable to a number of oceanographic and environmental sample types. Targeted pools are dissolved methane, dissolved organic carbon (DOC), dissolved inorganic carbon (DIC), solid organic matrices (e.g., seston, tissue and sediments), biomarkers and short chained (C 1 -C 5 ) hydrocarbons from methane hydrates. In most instances, the extraction, distillation and graphitization events are continuous within the system, thus, minimizing the possibility of fractionation or contamination during sample processing. A variety of methods are employed to extract carbon compounds and convert them to CO 2 for graphitization. Dissolved methane and DIC from the same sample are sparged and cryogenically separated before the methane is oxidized in a high temperature oxygen stream. DOC is oxidized to CO 2 by 1200 W ultraviolet photo-oxidation lamp, and solids oxidized in sealed, evacuated tubes. Hydrocarbons liberated from the disassociation of gas hydrates are cryogenically separated with a cryogenic temperature control unit, and biomarkers separated and concentrated by preparative capillary gas chromatography (PCGC). With this system, up to 20 samples, standards or blanks can be processed per day

Vacuum membrane distillation of liquid desiccants Utilizing Hollow Fiber Membranes

KAUST Repository

Lefers, Ryan

2018-01-31

This paper documents the testing of a vacuum membrane distillation system intended for use with liquid desiccants. Liquid desiccants offer the possibility for low-energy, ambient temperature dehumidification. Effective desalination and purification of diluted desiccants outputs two important products: a concentrated desiccant for reuse in dehumidification and fresh water. In this study, vacuum membrane distillation was used in the laboratory to purify diluted liquid desiccants. Calcium chloride and magnesium chloride were the desiccants selected for testing. Desiccant solutions were pumped through the lumens of poly(vinylidene fluoride) (PVDF) hollow fiber membranes at varying feed inlet temperatures, solution velocity rates and vacuum set points during membrane distillation. An average flux of 8 kg m-2 h-1 was obtained using 30 wt% magnesium chloride solution at a temperature of 50 °C while applying vacuum to achieve 25 mbar absolute pressure on the air side of the membrane. The results are promising for the development of a full-scale vacuum membrane distillation process for desiccant solution regeneration and fresh water recovery. In addition, the recovered condensate was of sufficient quality for use in agricultural irrigation or drinking water.

Vacuum membrane distillation of liquid desiccants Utilizing Hollow Fiber Membranes

KAUST Repository

Lefers, Ryan; Srivatsa Bettahalli, N.M.; Fedoroff, Nina V.; Nunes, Suzana Pereira; Leiknes, TorOve

2018-01-01

This paper documents the testing of a vacuum membrane distillation system intended for use with liquid desiccants. Liquid desiccants offer the possibility for low-energy, ambient temperature dehumidification. Effective desalination and purification of diluted desiccants outputs two important products: a concentrated desiccant for reuse in dehumidification and fresh water. In this study, vacuum membrane distillation was used in the laboratory to purify diluted liquid desiccants. Calcium chloride and magnesium chloride were the desiccants selected for testing. Desiccant solutions were pumped through the lumens of poly(vinylidene fluoride) (PVDF) hollow fiber membranes at varying feed inlet temperatures, solution velocity rates and vacuum set points during membrane distillation. An average flux of 8 kg m-2 h-1 was obtained using 30 wt% magnesium chloride solution at a temperature of 50 °C while applying vacuum to achieve 25 mbar absolute pressure on the air side of the membrane. The results are promising for the development of a full-scale vacuum membrane distillation process for desiccant solution regeneration and fresh water recovery. In addition, the recovered condensate was of sufficient quality for use in agricultural irrigation or drinking water.

27 CFR 19.643 - Brand name, kind, alcohol content, and State of distillation.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Brand name, kind, alcohol... Bottle and Label Requirements Bottle Label Requirements § 19.643 Brand name, kind, alcohol content, and State of distillation. (a) Brand name and kind. The label of distilled spirits shall state the brand...

Carbon isotope fractionation of 1,1,1-trichloroethane during base-catalyzed persulfate treatment

International Nuclear Information System (INIS)

Marchesi, Massimo; Thomson, Neil R.; Aravena, Ramon; Sra, Kanwartej S.; Otero, Neus; Soler, Albert

2013-01-01

Highlights: • Treatability and C fractionation of 1,1,1-TCA by base-catalyzed S 2 O 8 2− was studied. • The rate of degradation of 1,1,1-TCA increased with a higher OH − :S 2 O 8 2− ratio. •Base-catalyzed S 2 O 8 2− can potentially treat recalcitrant compound like 1,1,1-TCA. • An enrichment factor of −7.0‰ independent of the OH − :S 2 O 8 2− ratio was obtained. • Carbon isotope can potentially be used to estimate the ISCO treatment efficacy. -- Abstract: The extent of carbon isotope fractionation during degradation of 1,1,1-trichloroethane (1,1,1-TCA) by a base-catalyzed persulfate (S 2 O 8 2− ) treatment system was investigated. Significant destruction of 1,1,1-TCA was observed at a pH of ∼12. An increase in the NaOH:S 2 O 8 2− molar ratio from 0.2:1 to 8:1 enhanced the reaction rate of 1,1,1-TCA by a factor of ∼5 to yield complete (>99.9%) destruction. An average carbon isotope enrichment fractionation factor which was independent of the NaOH:S 2 O 8 2− molar ratio of −7.0 ± 0.2‰ was obtained. This significant carbon isotope fractionation and the lack of dependence on changes in the NaOH:S 2 O 8 2− molar ratio demonstrates that carbon isotope analysis can potentially be used in situ as a performance assessment tool to estimate the degradation effectiveness of 1,1,1-TCA by a base-catalyzed persulfate system

Distillation irrigation: a low-energy process for coupling water purification and drip irrigation

Science.gov (United States)

Constantz, J.

1989-01-01

A method is proposed for combining solar distillation and drip irrigation to simultaneously desalinize water and apply this water to row crops. In this paper, the basic method is illustrated by a simple device constructed primarily of sheets of plastic, which uses solar energy to distill impaired water and apply the distillate to a widely spaced row crop. To predict the performance of the proposed device, an empirical equation for distillate production, dp, is developed from reported solar still production rates, and a modified Jensen-Haise equation is used to calculate the potential evapotranspiration, et, for a row crop. Monthly values for et and dp are calculated by using a generalized row crop at five locations in the Western United States. Calculated et values range from 1 to 22 cm month-1 and calculated dp values range from 2 to 11 cm month-1, depending on the location, the month, and the crop average. When the sum of dp plus precipitation, dp + P, is compared to et for the case of 50% distillation irrigation system coverage, the results indicate that the crop's et is matched by dp + P, at the cooler locations only. However, when the system coverage is increased to 66%, the crop's et is matched by dp + P even at the hottest location. Potential advantages of distillation irrigation include the ability: (a) to convert impaired water resources to water containing no salts or sediments; and (b) to efficiently and automatically irrigate crops at a rate that is controlled primarily by radiation intensities. The anticipated disadvantages of distillation irrigation include: (a) the high costs of a system, due to the large amounts of sheeting required, the short lifetime of the sheeting, and the physically cumbersome nature of a system; (b) the need for a widely spaced crop to reduce shading of the system by the crop; and (c) the production of a concentrated brine or precipitate, requiring proper off-site disposal. ?? 1989.

Characterization of commercial ceramic adsorbents and their application on naphthenic acids removal of petroleum distillates; Caracterizacao de adsorventes ceramicos comerciais e sua aplicacao na remocao de acidos naftenicos de destilados de petroleo

Energy Technology Data Exchange (ETDEWEB)

Silva, J.P.; Senna, L.F. de; Lago, D.C.B. do; Silva Junior, P.F. da; Figueiredo, M.A.G. de; Dias, E.G. [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)], e-mail: julia_psi@yahoo.com.br; Chiaro, S.S.X. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2006-07-01

One denominates 'naphthenic acids' to the mixture of carboxylic acids that is present in petroleum oil, and is directly responsible for its acidity and corrosiveness in liquid phase during the refine process. These acids are also presents in distilled fraction of petroleum, causing several problems in final products quality. A possible way to remove them from petroleum distilled fractions is the adsorption in porous materials. However, the published results indicate that ion exchange resins would be the best adsorbents for this process, which would probably increase its cost. In this work, two commercial adsorbents (clay and activated alumina) were characterized by a set of physical-chemistry techniques and evaluated concerning their capacity of removing naphthenic acids from a light petroleum fraction. It was also verified the influence of a previous thermal treatment to the adsorption in their physical-chemistry characteristics and its properties. (author)

Simulators of tray distillation columns as tools for interpreting gamma-ray scan profile signal

International Nuclear Information System (INIS)

Offei-Mensah, P.S.; Gbadago, J.K.; Dagadu, C.P.K.; Danso, K.A.

2008-01-01

Simulators of tray distillation columns were used to provide technical guidelines for interpreting signals from gamma ray scans used for analysing malfunctions in distillation columns. The transmitted radiation intensities at 0.05 m intervals were determined from top to bottom of simulators of tray distillation columns exposed to 20 mCi of '1'3'7 Cs. Signals generated from the simulators were identical with the experimental signals obtained from the stabilizer column of the crude oil distillation unit at the Tema Oil Refinery Ghana Limited. Changes in the signal level were observed with changes in diameter, type of material (gasoline, air, debris, steel) and orientation of scan line. The analysis provided accurate interpretation of gamma scan profiles. (au)

The usefulness of intermediate products of plum processing for alcoholic fermentation and chemical composition of the obtained distillates.

Science.gov (United States)

Balcerek, Maria; Pielech-Przybylska, Katarzyna; Patelski, Piotr; Sapińska, Ewelina; Księżopolska, Mirosława

2013-05-01

In this study, an evaluation of intermediate products of plum processing as potential raw materials for distillates production was performed. Effects of composition of mashes on ethanol yield, chemical composition and taste, and flavor of the obtained spirits were determined. The obtained results showed that spontaneous fermentations of the tested products of plum processing with native microflora of raisins resulted in lower ethanol yields, compared to the ones fermented with wine yeast Saccharomyces bayanus. The supplementation of mashes with 120 g/L of sucrose caused an increase in ethanol contents from 6.2 ± 0.2 ÷ 6.5 ± 0.2% v/v in reference mashes (without sucrose addition, fermented with S. bayanus) to ca. 10.3 ± 0.3% v/v, where its highest yields amounted to 94.7 ± 2.9 ÷ 95.6 ± 2.9% of theoretical capacity, without negative changes in raw material originality of distillates. The concentrations of volatile compounds in the obtained distillates exceeding 2000 mg/L alcohol 100% v/v and low content of methanol and hydrocyanic acid, as well as their good taste and aroma make the examined products of plum processing be very attractive raw materials for the plum distillates production. © 2013 Institute of Food Technologists®

Preparation of 6,6,1',1',6',6'-hexadeutero sucrose.

Science.gov (United States)

Gouy, Marie-Hélène; Danel, Mathieu; Gayral, Maud; Bouchu, Alain; Queneau, Yves

2007-11-05

The preparation of 6,6,1',1',6',6'-hexadeutero sucrose is reported. The synthesis is based on a triple oxidation of a protected sucrose 6,1',6'-triol to the corresponding 6,1',6'-tricarboxylic acid or ester, followed by reduction with lithium aluminium deuteride. This triple oxidation could be achieved either using cat. TEMPO-NaOCl (to the acid) or PDC-Ac(2)O-t-BuOH (to the t-butyl carboxylic ester).

Towards energy efficient distillation technologies – Making the right choice

International Nuclear Information System (INIS)

Kiss, Anton A.; Flores Landaeta, Servando J.; Infante Ferreira, Carlos A.

2012-01-01

In spite of claiming around half of the operational costs of chemical plants, distillation is still the most popular separation technology. Distillation has low thermodynamic efficiency, requiring the input of high quality energy in the reboiler – while rejecting a similar amount of heat at lower temperature, in the condenser. Several heat pump concepts have been proposed to upgrade that thermal energy and reduce the consumption of valuable utilities. Under certain conditions, the energy savings of heat pump assisted distillation is usually around 20–50%. This study proposes a novel selection scheme of energy efficient distillation technologies, with a special focus on heat pumps. The most promising technologies selected are vapor compression, mechanical or thermal vapor recompression, absorption, compression–resorption and thermo-acoustic heat pumps, multi-effect distillation, heat integrated distillation column, cyclic distillation, Kaibel and dividing-wall column. The scheme considers as the main selection criteria the type of separation tasks, product flow and specifications, operating pressure, difference in boiling points, reboiler duty and its temperature level. Moreover, this scheme is very practical, allowing major time and resources savings in the design of eco-efficient processes. -- Highlights: ► Heat pump assisted distillation with energy savings of 20–50%. ► Novel and practical selection scheme of energy efficient distillation technologies. ► Evaluation of promising technologies: VC, MVR, TVR, AHP, CHRP, TAHP, HIDiC, DWC, CyDist. ► Selection criteria include: ΔT b , ΔT lift , P, T reb , Q reb , volatility. ► Design of eco-efficient processes with high COP, and lower TIC and TAC.

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow