WorldWideScience

Sample records for dish technology analyses

  1. Solar parabolic dish technology evaluation report

    Lucas, J. W.

    1984-01-01

    The activities of the JPL Solar Thermal Power Systems Parabolic Dish Project for FY 1983 are summarized. Included are discussions on designs of module development including concentrator, receiver, and power conversion subsystems together with a separate discussion of field tests, Small Community Experiment system development, and tests at the Parabolic Dish Test Site.

  2. White Paper on Dish Stirling Technology: Path Toward Commercial Deployment

    Andraka, Charles E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Stechel, Ellen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Becker, Peter [Stirling Energy Systems, Scottsdale, AZ (United States); Messick, Brian [Stirling Energy Systems, Scottsdale, AZ (United States)

    2016-07-01

    Dish Stirling energy systems have been developed for distributed and large-scale utility deployment. This report summarizes the state of the technology in a joint project between Stirling Energy Systems, Sandia National Laboratories, and the Department of Energy in 2011. It then lays out a feasible path to large scale deployment, including development needs and anticipated cost reduction paths that will make a viable deployment product.

  3. Dish concentrators for solar thermal energy - Status and technology development

    Jaffe, L. D.

    1981-01-01

    Comparisons are presented of point-focusing, or 'dish' solar concentrator system features, development status, and performance levels demonstrated to date. In addition to the requirements of good optical efficiency and high geometric concentration ratios, the most important future consideration in solar thermal energy dish concentrator design will be the reduction of installed and lifetime costs, as well as the materials and labor costs of production. It is determined that technology development initiatives are needed in such areas as optical materials, design wind speeds and wind loads, structural configuration and materials resistance to prolonged exposure, and the maintenance of optical surfaces. The testing of complete concentrator systems, with energy-converting receivers and controls, is also necessary. Both reflector and Fresnel lens concentrator systems are considered.

  4. Dish concentrators for solar thermal energy: Status and technology development

    Jaffe, L. D.

    1982-01-01

    Point-focusing concentrators under consideration for solar thermal energy use are reviewed. These concentrators differ in such characteristics as optical configuration, optical materials, structure for support of the optical elements and of the receiver, mount, foundation, drive, controls and enclosure. Concentrator performance and cost are considered. Technology development is outlined, including wind loads and aerodynamics; precipitation, sand, and seismic considerations; and maintenance and cleaning.

  5. Summary assessment of solar thermal parabolic dish technology for electrical power generation

    Penda, P. L.; Fujita, T.; Lucas, J. W.

    1985-01-01

    An assessment is provided of solar thermal parabolic dish technology for electrical power generation. The assessment is based on the development program undertaken by the Jet Propulsion Laboratory for the U.S. Department of Energy and covers the period from the initiation of the program in 1976 through mid-1984. The program was founded on developing components and subsystems that are integrated into parabolic dish power modules for test and evaluation. The status of the project is summarized in terms of results obtained through testing of modules, and the implications of these findings are assessed in terms of techno-economic projections and market potential. The techno-economic projections are based on continuation of an evolutionary technological development program and are related to the accomplishments of the program as of mid-1984. The accomplishments of the development effort are summarized for each major subsystem including concentrators, receivers, and engines. The ramifications of these accomplishments are assessed in the context of developmental objectives and strategies.

  6. Enhancing economic competiveness of dish Stirling technology through production volume and localization: Case study for Morocco

    Larchet, Kevin; Guédez, Rafael; Topel, Monika; Gustavsson, Lars; Machirant, Andrew; Hedlund, Maria-Lina; Laumert, Björn

    2017-06-01

    The present study quantifies the reduction in the levelized cost of electricity (LCoE) and capital expenditure (CAPEX) of a dish Stirling power plant (DSPP) through an increase in localization and unit production volume. Furthermore, the localization value of the plant is examined to determine how much investment is brought into the local economy. Ouarzazate, Morocco, was chosen as the location of the study due to the country's favorable regulatory framework with regards to solar power technologies and its established industry in the concentrating solar power (CSP) field. A detailed techno-economic model of a DSPP was developed using KTH's in-house modelling tool DYESOPT, which allows power plant evaluation by means of technical and economic performance indicators. Results on the basis of LCoE and CAPEX were compared between two different cases of production volume, examining both a minimum and maximum level of localization. Thereafter, the DSPP LCoE and localization value were compared against competing solar technologies to evaluate its competitiveness. In addition, a sensitivity analysis was conducted around key design parameters. The study confirms that the LCoE of a DSPP can be reduced to values similar to solar photovoltaic (PV) and lower than other CSP technologies. Furthermore, the investment in the local economy is far greater when compared to PV and of the same magnitude to other CSP technologies. The competiveness of a DSPP has the potential to increase further when coupled with thermal energy storage (TES), which is currently under development.

  7. Fort Huachuca to Benefit from New Solar Technology: Dish-Stirling System Couples Solar Power with Engine to Generate Electricity

    1995-01-01

    ... in partnership with industry. A prototype dish-Stirling solar system, which consists of a large dish of solar concentrators and a Stirling heat engine, will be installed at Fort Huachuca in July and should be in operation about two weeks later...

  8. Disease-in-a-dish: the contribution of patient-specific induced pluripotent stem cell technology to regenerative rehabilitation.

    Mack, David L; Guan, Xuan; Wagoner, Ashley; Walker, Stephen J; Childers, Martin K

    2014-11-01

    Advances in regenerative medicine technologies will lead to dramatic changes in how patients in rehabilitation medicine clinics are treated in the upcoming decades. The multidisciplinary field of regenerative medicine is developing new tools for disease modeling and drug discovery based on induced pluripotent stem cells. This approach capitalizes on the idea of personalized medicine by using the patient's own cells to discover new drugs, increasing the likelihood of a favorable outcome. The search for compounds that can correct disease defects in the culture dish is a conceptual departure from how drug screens were done in the past. This system proposes a closed loop from sample collection from the diseased patient, to in vitro disease model, to drug discovery and Food and Drug Administration approval, to delivering that drug back to the same patient. Here, recent progress in patient-specific induced pluripotent stem cell derivation, directed differentiation toward diseased cell types, and how those cells can be used for high-throughput drug screens are reviewed. Given that restoration of normal function is a driving force in rehabilitation medicine, the authors believe that this drug discovery platform focusing on phenotypic rescue will become a key contributor to therapeutic compounds in regenerative rehabilitation.

  9. Mini-guts in a dish: Perspectives of adult Cystic Fibrosis (CF) patients and parents of young CF patients on organoid technology.

    Boers, Sarah N; de Winter-de Groot, Karin M; Noordhoek, Jacquelien; Gulmans, Vincent; van der Ent, Cornelis K; van Delden, Johannes J M; Bredenoord, Annelien L

    2018-03-06

    Organoid technology enables the cultivation of human tissues in a dish. Its precision medicine potential could revolutionize the Cystic Fibrosis (CF) field. We provide a first thematic exploration of the patient perspective on organoid technology to set the further research agenda, which is necessary for responsible development of this ethically challenging technology. 23 semi-structured qualitative interviews with 14 Dutch adult CF patients and 12 parents of young CF patients to examine their experiences, opinions, and attitudes regarding organoid technology. Four themes emerged: (1) Respondents express a close as well as a distant relationship to organoids; (2) the open-endedness of organoid technology sparks hopes and concerns, (3) commercial use evokes cautiousness. (4) Respondents mention the importance of sound consent procedures, long-term patient engagement, responsible stewardship, and stringent conditions for commercial use. The precision medicine potential of organoid technology can only be realized if the patient perspective is taken adequately into account. Copyright © 2018 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

  10. The phaco machine: analysing new technology.

    Fishkind, William J

    2013-01-01

    The phaco machine is frequently overlooked as the crucial surgical instrument it is. Understanding how to set parameters is initiated by understanding fundamental concepts of machine function. This study analyses the critical concepts of partial occlusion phaco, occlusion phaco and pump technology. In addition, phaco energy categories as well as variations of phaco energy production are explored. Contemporary power modulations and pump controls allow for the enhancement of partial occlusion phacoemulsification. These significant changes in the anterior chamber dynamics produce a balanced environment for phaco; less complications; and improved patient outcomes.

  11. Dish/Stirling for Department of Defense applications final report

    Diver, R.B.; Menicucci, D.F. [Sandia National Labs., Albuquerque, NM (United States). Energy and Environment Div.

    1997-03-01

    This report describes a Strategic Environmental Research and Development Program (SERDP) project to field a dish/Stirling system at a southwestern US military facility. This project entitled ``Dish/Stirling for DoD Applications`` was started in August 1993 and was completed in September 1996. The project`s objective was to assist military facilities to field and evaluate emerging environmentally sound and potentially economical dish/Stirling technology. Dish/Stirling technology has the potential to produce electricity at competitive costs while at the same time providing a secure and environmentally benign source of power. In accordance with the SERDP charter, this project leveraged a US Department of Energy (DOE) cost-shared project between Sandia National Laboratories and Cummins Power Generation, Inc. (CPG). CPG is a wholly owned subsidiary of Cummins Engine Company, a leading manufacturer of diesel engines. To accomplish this objective, the project called for the installation of a dish/Stirling system at a military facility to establish first-hand experience in the operation of a dish/Stirling system. To scope the potential DoD market for dish/Stirling technology and to identify the site for the demonstration, a survey of southwestern US military facilities was also conducted. This report describes the project history, the Cummins dish/Stirling system, results from the military market survey, and the field test results.

  12. γ-ray irradiation of cooked dishes

    Lin Ruotai; Cheng Wei; Wen Shengli; Xiong Guangquan; Ye Lixiu; Chen Yuxia; Zhang Jinmu; He Jianjun; Lin Yong; Zhan Hanping

    2005-01-01

    Ready-to-eat cooked dishes, including stir-fried dishes, steamed dishes, roast meat, deep dried dishes, shrimps and seashells, and dishes of local flavor, etc were irradiated with 60 Co γ-rays, and the decontamination effects were studied. The results showed that most of the cooked dishes are suitable for irradiation. The effective dose is 4 kGy to 8 kGy. Index of microbe of the irradiated dishes was conformed to the National Food-Health standards, and no significant sensory changes was observed with the irradiated dishes. The quality guarantee period (0-5 degree C) is 60 days. (authors)

  13. Technology advancement for integrative stem cell analyses.

    Jeong, Yoon; Choi, Jonghoon; Lee, Kwan Hyi

    2014-12-01

    Scientists have endeavored to use stem cells for a variety of applications ranging from basic science research to translational medicine. Population-based characterization of such stem cells, while providing an important foundation to further development, often disregard the heterogeneity inherent among individual constituents within a given population. The population-based analysis and characterization of stem cells and the problems associated with such a blanket approach only underscore the need for the development of new analytical technology. In this article, we review current stem cell analytical technologies, along with the advantages and disadvantages of each, followed by applications of these technologies in the field of stem cells. Furthermore, while recent advances in micro/nano technology have led to a growth in the stem cell analytical field, underlying architectural concepts allow only for a vertical analytical approach, in which different desirable parameters are obtained from multiple individual experiments and there are many technical challenges that limit vertically integrated analytical tools. Therefore, we propose--by introducing a concept of vertical and horizontal approach--that there is the need of adequate methods to the integration of information, such that multiple descriptive parameters from a stem cell can be obtained from a single experiment.

  14. Theoretical modelling of solar dish concentrator

    Yaaseen Rafeeu; Mohd Zainal Abidin Abdul Kadir; Senan Mohamed Abdulla; Nor Mariah Adam

    2009-01-01

    Full text: Concentrating solar power (CSP) technologies could be one of the major contributor to worlds future energy needs and which would be cheap and clean sources of energy. This would improve energy utilization, higher conversion efficiency with reliable and affordable supply of electricity to the public. The proposed approach is using different size and depth of solar dish concentrators to improve solar fraction using the aluminium foil as reflector. In this paper, different measurement of solar concentrators is investigated and aims to aims to introducing an improved methodology for solar fraction on incoming solar energy in wet climate. (author)

  15. Dysphagia due to diffuseidiopathic skeletal hyperostosis (DISH ...

    Diffuse idiopathic skeletal hyperostosis (DISH) or Forestier's disease isa form of degenerative arthritiswith unique spinal and extra spinal manifestations. Dysphagia due to DISH is uncommon but when present DISH should be suspected. Surgical decompression can relieve some of the symptoms. We report a case of a 60 ...

  16. Performance Analyses in an Assistive Technology Service Delivery Process

    Petersen, Anne Karin

    Performance Analyses in an Assistive Technology Service Delivery Process.Keywords: process model, occupational performance, assistive technologiesThe Poster is about teaching students, using models and theory in education and practice. It is related to Occupational therapy process and professional...... af top-til-bund, klientcentreret og aktivitetsbaseret interventioner, ERGO/MunksgaardFisher, A. &, Griswold, L. A., 2014. Performance Skills. I: B.Schell red.2014 Occupational Therapy. Willard &Spackman’s occupational therapy. -12th ed., p.249-264Cook A.M., Polgar J.M. (2015) Assistive Technologies...

  17. Fifth parabolic dish solar thermal power program annual review: proceedings

    None

    1984-03-01

    The primary objective of the Review was to present the results of activities within the Parabolic Dish Technology and Module/Systems Development element of the Department of Energy's Solar Thermal Energy Systems Program. The Review consisted of nine technical sessions covering overall Project and Program aspects, Stirling and Brayton module development, concentrator and engine/receiver development, and associated hardware and test results to date; distributed systems operating experience; international dish development activities; and non-DOE-sponsored domestic dish activities. A panel discussion concerning business views of solar electric generation was held. These Proceedings contain the texts of presentations made at the Review, as submitted by their authors at the beginning of the Review; therefore, they may vary slightly from the actual presentations in the technical sessions.

  18. Dynamics of energy systems: Methods of analysing technology change

    Neij, Lena

    1999-05-01

    Technology change will have a central role in achieving a sustainable energy system. This calls for methods of analysing the dynamics of energy systems in view of technology change and policy instruments for effecting and accelerating technology change. In this thesis, such methods have been developed, applied, and assessed. Two types of methods have been considered, methods of analysing and projecting the dynamics of future technology change and methods of evaluating policy instruments effecting technology change, i.e. market transformation programmes. Two methods are focused on analysing the dynamics of future technology change; vintage models and experience curves. Vintage models, which allow for complex analysis of annual streams of energy and technological investments, are applied to the analysis of the time dynamics of electricity demand for lighting and air-distribution in Sweden. The results of the analyses show that the Swedish electricity demand for these purposes could decrease over time, relative to a reference scenario, if policy instruments are used. Experience curves are used to provide insight into the prospects of diffusion of wind turbines and photo voltaic (PV) modules due to cost reduction. The results show potential for considerable cost reduction for wind-generated electricity, which, in turn, could lead to major diffusion of wind turbines. The results also show that major diffusion of PV modules, and a reduction of PV generated electricity down to the level of conventional base-load electricity, will depend on large investments in bringing the costs down (through R D and D, market incentives and investments in niche markets) or the introduction of new generations of PV modules (e.g. high-efficiency mass-produced thin-film cells). Moreover, a model has been developed for the evaluation of market transformation programmes, i.e. policy instruments that effect technology change and the introduction and commercialisation of energy

  19. Preparation of environmental analyses for synfuel and unconventional gas technologies

    Reed, R.M. (ed.)

    1982-09-01

    Government agencies that offer financial incentives to stimulate the commercialization of synfuel and unconventional gas technologies usually require an analysis of environmental impacts resulting from proposed projects. This report reviews potentially significant environmental issues associated with a selection of these technologies and presents guidance for developing information and preparing analyses to address these issues. The technologies considered are western oil shale, tar sand, coal liquefaction and gasification, peat, unconventional gas (western tight gas sands, eastern Devonian gas shales, methane from coal seams, and methane from geopressured aquifers), and fuel ethanol. Potentially significant issues are discussed under the general categories of land use, air quality, water use, water quality, biota, solid waste disposal, socioeconomics, and health and safety. The guidance provided in this report can be applied to preparation and/or review of proposals, environmental reports, environmental assessments, environmental impact statements, and other types of environmental analyses. The amount of detail required for any issue discussed must, by necessity, be determined on a case-by-case basis.

  20. Development of core design and analyses technology for integral reactor

    Zee, Sung Quun; Lee, C. C.; Kim, K. Y.

    2002-03-01

    In general, small and medium-sized integral reactors adopt new technology such as passive and inherent safety concepts to minimize the necessity of power source and operator actions, and to provide the automatic measures to cope with any accidents. Specifically, such reactors are often designed with a lower core power density and with soluble boron free concept for system simplification. Those reactors require ultra long cycle operation for higher economical efficiency. This cycle length requirement is one of the important factors in the design of burnable absorbers as well as assurance of shutdown margin. Hence, both computer code system and design methodology based on the today's design technology for the current commercial reactor cores require intensive improvement for the small and medium-sized soluble boron free reactors. New database is also required for the development of this type of reactor core. Under these technical requirements, conceptual design of small integral reactor SMART has been performed since July 1997, and recently completed under the long term nuclear R and D program. Thus, the final objectives of this work is design and development of an integral reactor core and development of necessary indigenous design technology. To reach the goal of the 2nd stage R and D program for basic design of SMART, design bases and requirements adequate for ultra long cycle and soluble boron free concept are established. These bases and requirements are satisfied by the core loading pattern. Based on the core loading pattern, nuclear, and thermal and hydraulic characteristics are analyzed. Also included are fuel performance analysis and development of a core protection and monitoring system that is adequate for the soluble boron free core of an integral reactor. Core shielding design analysis is accomplished, too. Moreover, full scope interface data are produced for reactor safety and performance analyses and other design activities. Nuclear, thermal and

  1. FPGA applications for single dish activity at Medicina radio telescopes

    Bartolini, M.; Naldi, G.; Mattana, A.; Maccaferri, A.; De Biaggi, M.

    FPGA technologies are gaining major attention in the recent years in the field of radio astronomy. At Medicina radio telescopes, FPGAs have been used in the last ten years for a number of purposes and in this article we will take into exam the applications developed and installed for the Medicina Single Dish 32m Antenna: these range from high performance digital signal processing to instrument control developed on top of smaller FPGAs.

  2. Development of core design and analyses technology for integral reactor

    Zee, Sung Quun; Lee, C. C.; Song, J. S. and others

    1999-03-01

    Integral reactors are developed for the applications such as sea water desalination, heat energy for various industries, and power sources for large container ships. In order to enhance the inherent and passive safety features, low power density concept is chosen for the integral reactor SMART. Moreover, ultra-longer cycle and boron-free operation concepts are reviewed for better plant economy and simple design of reactor system. Especially, boron-free operation concept brings about large difference in core configurations and reactivity controls from those of the existing large size commercial nuclear power plants and also causes many differences in the safety aspects. The ultimate objectives of this study include detailed core design of a integral reactor, development of the core design system and technology, and finally acquisition of the system design certificate. The goal of the first stage is the conceptual core design, that is, to establish the design bases and requirements suitable for the boron-free concept, to develop a core loading pattern, to analyze the nuclear, thermal and hydraulic characteristics of the core and to perform the core shielding design. Interface data for safety and performance analyses including fuel design data are produced for the relevant design analysis groups. Nuclear, thermal and hydraulic, shielding design and analysis code systems necessary for the core conceptual design are established through modification of the existing design tools and newly developed methodology and code modules. Core safety and performance can be improved by the technology development such as boron-free core optimization, advaned core monitoring and operational aid system. Feasiblity study on the improvement of the core protection and monitoring system will also contribute toward core safety and performance. Both the conceptual core design study and the related technology will provide concrete basis for the next design phase. This study will also

  3. Development of core design and analyses technology for integral reactor

    Zee, Sung Quun; Lee, C. C.; Song, J. S. and others

    1999-03-01

    Integral reactors are developed for the applications such as sea water desalination, heat energy for various industries, and power sources for large container ships. In order to enhance the inherent and passive safety features, low power density concept is chosen for the integral reactor SMART. Moreover, ultra-longer cycle and boron-free operation concepts are reviewed for better plant economy and simple design of reactor system. Especially, boron-free operation concept brings about large difference in core configurations and reactivity controls from those of the existing large size commercial nuclear power plants and also causes many differences in the safety aspects. The ultimate objectives of this study include detailed core design of a integral reactor, development of the core design system and technology, and finally acquisition of the system design certificate. The goal of the first stage is the conceptual core design, that is, to establish the design bases and requirements suitable for the boron-free concept, to develop a core loading pattern, to analyze the nuclear, thermal and hydraulic characteristics of the core and to perform the core shielding design. Interface data for safety and performance analyses including fuel design data are produced for the relevant design analysis groups. Nuclear, thermal and hydraulic, shielding design and analysis code systems necessary for the core conceptual design are established through modification of the existing design tools and newly developed methodology and code modules. Core safety and performance can be improved by the technology development such as boron-free core optimization, advaned core monitoring and operational aid system. Feasiblity study on the improvement of the core protection and monitoring system will also contribute toward core safety and performance. Both the conceptual core design study and the related technology will provide concrete basis for the next design phase. This study will also

  4. Ideas for future large single dish radio telescopes

    Kärcher, Hans J.; Baars, Jacob W. M.

    2014-07-01

    The existing large single dish radio telescopes of the 100m class (Effelsberg, Green Bank) were built in the 1970s and 1990s. With some active optics they work now down to 3 millimeter wavelength where the atmospheric quality of the site is also a limiting factor. Other smaller single dish telescopes (50m LMT Mexico, 30m IRAM Spain) are located higher and reach sub-millimeter quality, and the much smaller 12m antennas of the ALMA array reach at a very high site the Terahertz region. They use advanced technologies as carbon fiber structures and flexible body control. We review natural limits to telescope design and use the examples of a number of telescopes for an overview of the available state-of-the-art in design, engineering and technologies. Without considering the scientific justification we then offer suggestions to realize ultimate performance of huge single dish telescopes (up to 160m). We provide an outlook on design options, technological frontiers and cost estimates.

  5. Parabolic dish collectors - A solar option

    Truscello, V. C.

    1981-05-01

    A description is given of several parabolic-dish high temperature solar thermal systems currently undergoing performance trials. A single parabolic dish has the potential for generating 20 to 30 kW of electricity with fluid temperatures from 300 to 1650 C. Each dish is a complete power-producing unit, and may function either independently or as part of a group of linked modules. The two dish designs under consideration are of 11 and 12 meter diameters, yielding receiver operating temperatures of 925 and 815 C, respectively. The receiver designs described include (1) an organic working fluid (toluene) Rankine cycle engine; (2) a Brayton open cycle unit incorporating a hybrid combustion chamber and nozzle and a shaft-coupled permanent magnet alternator; and (3) a modified Stirling cycle device originally designed for automotive use. Also considered are thermal buffer energy storage and thermochemical transport and storage.

  6. The Translation of Chinese Dish Names

    龚佳文

    2015-01-01

    The traditional food of a nation reflects its historical and cultural characteristics This thesis begins with an introduction to the translation situation of Chinese dish names and its existing problem nowadays, and proceeds to the translation principles and tactics for English translation of the names of Chinese dishes, based on Eugene A. Nida’ s Functional Equivalence, with an aim to improve translation efficiency and promote cross-cultural communication, and promoting Chinese food culture throughout the globe.

  7. Feasibility study of dish/stirling power systems in Turkey

    Zilanlı, Gülin Acarol; Eray, Aynur

    2017-06-01

    In this study, two different commercial dish/stirling systems, SES (Stirling Energy Systems) and WGA-ADDS (WGAssociates - Advanced Dish Development System), are modeled using the "System Advisor Model" (SAM) modeling software in designated settlement areas. Both systems are modeled for the US state of Albuquerque, where they were designed, and Turkish provinces of Ankara, Van, Muğla, Mersin, Urfa and Konya. At first, the dish/stirling system is optimized according to the power output values and the system loss parameters. Then, the layout of the solar field is designed with an installed capacity of 600kW both of SES and WGA-ADDS systems, Upon securing the most suitable layout, the system is modeled for the aforementioned settlements using the optimum output values gathered from the parametric analysis. As a result of the simulation studies, the applicability of this model is discussed according to the power output and the efficiency. Although Turkey is located in an area called "the sun belt" where solar energy technologies can be used, there is no advanced application of these systems. This study aims to discuss the application of these systems in detail and to pave the way for future studies in this field.

  8. Application of carbon isotope analyses in food technology

    Szanto, Zsuzsa; Svingor, E.; Futo, I.; Palcsu, L.; Molnar, M.

    2001-01-01

    The vast economic size of the food market offers great temptations for the production and sale of fraudulent products, adulterated products and synthetic products that are labeled as natural ones. Conventional techniques of chemical analyses have served the food industry well for many years but are limited in their ability to detect certain types of fraudulent or mislabelled products. The aversion to added sugar and the demand for 'all natural' food products among consumers has led to a great deal of mislabelling on the part of food processors in order to achieve greater economic gain. The nature of deceptions detectable by carbon Stable Isotope Ratio Analysis (SIRA) in food technology falls into three broad categories. The most common is the adulteration of an expensive natural product, such as apple juice, with a much cheaper natural product such as cane sugar or high fructose corn syrup (HFCS). The second is outright falsification of a food. An example is maple syrup produced by simple addition of maple flavoring to a sugar syrup or HFCS. The third general category is the sale of synthetic materials as natural ones or the addition of synthetic materials to natural ones in order to increase the volume of the product. The procedure for using carbon SIRA in monitoring food products involves two stages. It must first be established that the product to be analyzed, or some specific component of it, has a particular isotopic composition that can be distinguished from that of the materials that might be used to adulterate it. Potential adulterating components are then analyzed to establish their isotopic identity. The carbon SIRA method cannot, in general, be used to establish purity unequivocally but it can be used to establish impurity or adulteration with a high degree of success. The overall process of carbon SIRA consists of three stages: selection of the sample or the isolation of the particular compound to be analyzed, conversion of this compound into CO 2 gas

  9. The internationalisation of technology analysed with patent data

    Bruno Van Pottelsberghe; Dominique Guellec

    2001-01-01

    This paper presents three new patent-based indicators of internationalisation of technology reflecting international co-operation in research and the location of research facilities of multinational firms. They witness both an increasing trend towards the globalisation of technology in the OECD area and large cross-country differences in the extent of internationalisation. An empirical analysis shows that the degree of technological internationalisation is higher for small countries and for c...

  10. Analysing Teacher Knowledge for Technology Education in Primary Schools

    Rohaan, Ellen J.; Taconis, Ruurd; Jochems, Wim M. G.

    2012-01-01

    Teacher knowledge guides a teacher's behaviour in the classroom. Teacher knowledge for technology education is generally assumed to play an important role in affecting pupils' learning in technology. There are an abundant number of teacher knowledge models that visualise different domains of teacher knowledge, but clear empirical evidence on how…

  11. Differences in nutrient and energy contents of commonly consumed dishes prepared in restaurants v. at home in Hunan Province, China.

    Jia, Xiaofang; Liu, Jiawu; Chen, Bo; Jin, Donghui; Fu, Zhongxi; Liu, Huilin; Du, Shufa; Popkin, Barry M; Mendez, Michelle A

    2018-05-01

    Eating away from home is associated with poor diet quality, in part due to less healthy food choices and larger portions. However, few studies account for the potential additional contribution of differences in food composition between restaurant- and home-prepared dishes. The present study aimed to investigate differences in nutrients of dishes prepared in restaurants v. at home. Eight commonly consumed dishes were collected in twenty of each of the following types of locations: small and large restaurants, and urban and rural households. In addition, two fast-food items were collected from ten KFC, McDonald's and food stalls. Five samples per dish were randomly pooled from every location. Nutrients were analysed and energy was calculated in composite samples. Differences in nutrients of dishes by preparation location were determined. Hunan Province, China. Na, K, protein, total fat, fatty acids, carbohydrate and energy in dishes. On average, both the absolute and relative fat contents, SFA and Na:K ratio were higher in dishes prepared in restaurants than households (P < 0·05). Protein was 15 % higher in animal food-based dishes prepared in households than restaurants (P<0·05). Quantile regression models found that, at the 90th quantile, restaurant preparation was consistently negatively associated with protein and positively associated with the percentage of energy from fat in all dishes. Moreover, restaurant preparation also positively influenced the SFA content in dishes, except at the highest quantiles. These findings suggest that compared with home preparation, dishes prepared in restaurants in China may differ in concentrations of total fat, SFA, protein and Na:K ratio, which may further contribute, beyond food choices, to less healthy nutrient intakes linked to eating away from home.

  12. Temperature Performance Evaluation of Parabolic Dishes Covered ...

    Aweda

    The parabolic dish with glass material gave the highest temperature of .... 3: Second day variation temperature and time using different materials. 8. 10 .... the sun rays at that particular time. ... especially between 11:00 am and 3:00 pm when.

  13. Temperature Performance Evaluation of Parabolic Dishes Covered ...

    Solar radiation reaching the earth is considered to be affected by some parameters like diffusion. This radiation is reflected or scattered by air molecules, cloud and aerosols (dust). Parabolic dishes made of different materials (glass, foil and painted surface) were used to concentrate energy on a copper calorimeter filled with ...

  14. Overview of ESO Large Single Dish Study

    Testi, Leonardo

    2018-01-01

    In this talk I will briefly summarize the motivation, methodology and outcome of the ESO Submm Single Dish Strategy WG. The WG was established by the ESO Director for Science and completed its work at the end of 2015. I will summarize the status of the report recommendations, which, among other things, led to the organization of the AtLAST workshop.

  15. Experimental studies on solar parabolic dish cooker with porous medium

    Lokeswaran, S.; Eswaramoorthy, M.

    2012-01-01

    The solar cooking is the alternate method of cooking to reduce consumptions of fossil fuels. An affordable, energy efficient solar cooking technology is much need due to the fossil fuels increasing cost and it is the hottest research topic in all over the world. This paper presents an experimental analysis of the heat transfer enhancement of solar parabolic dish cookers by a porous medium made of scrap material. Using the stagnation temperature test and water boiling test are conducted on the cooking vessel with and without porous medium. Experimental results are compared for both cases in terms of thermal performance, optical efficiency, heat loss factor and cooking power. (authors)

  16. Analyses and Forecasting of Smart Grid Technological Dynamics

    I. V. Danilin

    2017-01-01

    Full Text Available Purpose: this paper analyzes and forecasts medium- to long-term dynamics of Smart Grid technology developments considering both patent activity and socio-economic (demand-side issues and requirements of economy and power system factors. Methods: for the analysis of Smart Grid patent data (IIP, USPTO, and WIPO patent databases used we apply syntactic semantic analysis of texts in natural languages and logistic curve-based method. We propose Exactus Patent system for intelligent full-text search and analysis of patents (results verified with Thomson Innovation and TotalPatent patent search systems. For interpretation of revealed dynamics and forecasting of future conditions we identify key long-term socio-economic factors drivers for Smart Grid development. Elements of C. Christensen (disruptive innovations and G. Dosi (technological trajectories theories were applied. Results: the study reveals a fast technological transformation within the Smart Grid domain due to the long-term socio-economic factors such as rise of renewables; energy efficiency and energy security issues; environmental constraints and shift of values; requirements for accelerated grid construction (in developing economies and grid modernization (in developed ones; ongoing economy-wide digitalization. Due to the limited economic effects of Smart Grid roll-outs (considering major requirements of economic agents and society and considering progressions of patent dynamics, authors forecasts technology stagnation (in terms of number of patents growth by the end of 2010-s as end of Gartner`s hype development stage. Conclusions and Relevance: a foreseen change in dynamics of Smart Grid technology development is interpreted as a manifestation of sinusoidal fluctuations in technology development for disruptive technologies (supported with OECD data. A longer cycle (in comparison with other disruptive technologies is interpreted as consequence of technology and industry specifics

  17. Using perceptual control theory to analyse technology integration in teaching

    D W Govender

    2013-07-01

    Full Text Available Contrary to the more traditional scenario of instructor-focused presentation, contemporary education allows individuals to embrace modern technological advances such as computers to concur with, conceptualize and substantiate matters presented before them. Transition from instructor-focused to student-centred presentation is prone to dissension and strife, motivating educators to assess elements of learner-centred teaching in conjunction with traditional teaching mechanisms and how individuals perceive and comprehend information (Andersson, 2008; Kiboss, 2010; United Nations Educational, Scientific and Cultural Organization (UNESCO, 2004. Computers can assist when used in the traditional teacher-student interface, but consideration must be given to teaching method variations and the students embracing these learning applications. If learner-centred teaching is to become accepted certain elements need to be introduced: revision of educators’ learning and teaching applications, time to facilitate knowledge and use of applicable contemporary technologies, and methods compatible with various technologies (Kiboss, 2010. Change is often not easy – while acknowledging the need to alter and revise methods they were taught to instil, educators may fail to embrace incorporation of technology into their teaching platform. Why are educators, who are quite knowledgeable and competent in computer applications and their merits, failing to embrace the benefits of technology in the classroom? A critical assessment of this mandates a transdisciplinary disposition in order to come to an amenable resolution. Perception, inhibition, ignorance and goals are just some reasons why educators are reluctant to incorporate technology despite their proficiency. Perceptual control theory (PCT will be implemented to assess these reasons as a means towards achieving change and assessing how to move forward. Issues associated with educators’ short- and long-term goals as

  18. On the evolution, over four generations of paraboloidal dish solar thermal electric power systems

    Kaneff, S.

    1993-01-01

    After a decade of supplying useful power, the White Cliffs Paraboloidal Dish Solar Thermal Power Station (1100 km west of Sydney) is still operational and has provided major lessons and experience for subsequent developments; particularly for the Molokai/Alburquerque unit built jointly with Power Kinetics Inc (of Troy, USA) for the US Department of Energy. This has, in turn, given valuable guidance for the third generation system now nearing completion in Canberra and employing new collector concepts refined for commercial production and viability. Unlike much dish-oriented R and D, we consider systems of dish arrays supplying central plant as a more attractive proposition than assemblies of dish/engine units, for all but very small systems (<2 MWe). Development has recently commerce on the fourth generation technology which result in a 2 MWe dish system within 2 years, expected to be followed closely by a system of 10 to 20 MWe, preparatory to still larger systems, as the technology evolves and experience is gained. The rationale in this progression in based on the achievement of commercial cost-effectiveness in competition with other energy sources. The direction of evolution is becoming clear and application of the technology to broader spheres than electricity generation is likely. Because of the nature of production methods employed and the ease of installation, system implementation can be rapid. (Author) 29 refs

  19. Analysing Models as a Knowledge Technology in Transport Planning

    Gudmundsson, Henrik

    2011-01-01

    critical analytic literature on knowledge utilization and policy influence. A simple scheme based in this literature is drawn up to provide a framework for discussing the interface between urban transport planning and model use. A successful example of model use in Stockholm, Sweden is used as a heuristic......Models belong to a wider family of knowledge technologies, applied in the transport area. Models sometimes share with other such technologies the fate of not being used as intended, or not at all. The result may be ill-conceived plans as well as wasted resources. Frequently, the blame...... device to illuminate how such an analytic scheme may allow patterns of insight about the use, influence and role of models in planning to emerge. The main contribution of the paper is to demonstrate that concepts and terminologies from knowledge use literature can provide interpretations of significance...

  20. Concentrating Solar Power Projects - Dish/Engine Projects | Concentrating

    Solar Power | NREL Dish/Engine Projects Photo of several flat, octagonal panels arranged together to form a dish-shaped structure. The receiver is supported above the panels by an arm-like of the panels. These dish/Stirling units are being tested at Sandia National Laboratories in

  1. Enabling Detailed Energy Analyses via the Technology Performance Exchange: Preprint

    Studer, D.; Fleming, K.; Lee, E.; Livingood, W.

    2014-08-01

    One of the key tenets to increasing adoption of energy efficiency solutions in the built environment is improving confidence in energy performance. Current industry practices make extensive use of predictive modeling, often via the use of sophisticated hourly or sub-hourly energy simulation programs, to account for site-specific parameters (e.g., climate zone, hours of operation, and space type) and arrive at a performance estimate. While such methods are highly precise, they invariably provide less than ideal accuracy due to a lack of high-quality, foundational energy performance input data. The Technology Performance Exchange was constructed to allow the transparent sharing of foundational, product-specific energy performance data, and leverages significant, external engineering efforts and a modular architecture to efficiently identify and codify the minimum information necessary to accurately predict product energy performance. This strongly-typed database resource represents a novel solution to a difficult and established problem. One of the most exciting benefits is the way in which the Technology Performance Exchange's application programming interface has been leveraged to integrate contributed foundational data into the Building Component Library. Via a series of scripts, data is automatically translated and parsed into the Building Component Library in a format that is immediately usable to the energy modeling community. This paper (1) presents a high-level overview of the project drivers and the structure of the Technology Performance Exchange; (2) offers a detailed examination of how technologies are incorporated and translated into powerful energy modeling code snippets; and (3) examines several benefits of this robust workflow.

  2. Technology application analyses at five Department of Energy Sites

    1995-05-01

    The Hazardous Waste Remedial Actions Program (HAZWRAP), a division of Lockheed Martin Energy Systems, Inc., managing contractor for the Department of Energy (DOE) facilities in Oak Ridge, Tennessee, was tasked by the United States Air Force (USAF) through an Interagency Agreement between DOE and the USAF, to provide five Technology Application Analysis Reports to the USAF. These reports were to provide information about DOE sites that have volatile organic compounds contaminating soil or ground water and how the sites have been remediated. The sites were using either a pump-and-treat technology or an alternative to pump-and-treat. The USAF was looking at the DOE sites for lessons learned that could be applied to Department of Defense (DoD) problems in an effort to communicate throughout the government system. The five reports were part of a larger project undertaken by the USAF to look at over 30 sites. Many of the sites were DoD sites, but some were in the private sector. The five DOE projects selected to be reviewed came from three sites: the Savannah River Site (SRS), the Kansas City Site, and Lawrence Livermore National Laboratory (LLNL). SRS and LLNL provided two projects each. Both provided a standard pump-and-treat application as well as an innovative technology that is an alternative to pump-and-treat. The five reports on these sites have previously been published separately. This volume combines them to give the reader an overview of the whole project

  3. Solar parabolic dish Stirling engine system design, simulation, and thermal analysis

    Hafez, A.Z.; Soliman, Ahmed; El-Metwally, K.A.; Ismail, I.M.

    2016-01-01

    Highlights: • Modeling and simulation for different parabolic dish Stirling engine designs using Matlab®. • The effect of solar dish design features and factors had been taken. • Estimation of output power from the solar dish using Matlab®. • The present analysis provides a theoretical guidance for designing and operating solar parabolic dish system. - Abstract: Modeling and simulation for different parabolic dish Stirling engine designs have been carried out using Matlab®. The effect of solar dish design features and factors such as material of the reflector concentrators, the shape of the reflector concentrators and the receiver, solar radiation at the concentrator, diameter of the parabolic dish concentrator, sizing the aperture area of concentrator, focal Length of the parabolic dish, the focal point diameter, sizing the aperture area of receiver, geometric concentration ratio, and rim angle have been studied. The study provides a theoretical guidance for designing and operating solar parabolic dish Stirling engines system. At Zewail city of Science and Technology, Egypt, for a 10 kW Stirling engine; The maximum solar dish Stirling engine output power estimation is 9707 W at 12:00 PM where the maximum beam solar radiation applied in solar dish concentrator is 990 W/m"2 at 12:00 PM. The performance of engine can be improved by increasing the precision of the engine parts and the heat source efficiency. The engine performance could be further increased if a better receiver working fluid is used. We can conclude that where the best time for heating the fluid and fasting the processing, the time required to heat the receiver to reach the minimum temperature for operating the Solar-powered Stirling engine for different heat transfer fluids; this will lead to more economic solar dish systems. Power output of the solar dish system is one of the most important targets in the design that show effectiveness of the system, and this has achieved when we take

  4. Corned Beef: an Enigmatic Irish Dish

    Mac Con Iomaire, Máirtín; Gallagher, Pádraic Óg

    2011-01-01

    Corned beef and cabbage, which is consumed in America in large quantities each Saint Patrick’s Day (17th March), is considered by most Americans to be the ultimate Irish dish. However, corned beef and cabbage is seldom eaten in modern day Ireland. It is widely reported that Irish immigrants replaced their beloved bacon and cabbage with corned beef and cabbage when they arrived in America, drawing on the corned beef supplied by their neighbouring Jewish butchers, but not all commentators beli...

  5. Effect of soil-structure interaction on the seismic behaviour of pedestal-structure system in large dish antennas

    Bahador Pourhatami

    2017-12-01

    Full Text Available Regarding the progressive improvement in the territory of Space Technology in all developed countries and consequently developing countries including Islamic Republic of Iran, the optimization of design and utilization of the communication equipment has been paid more attention today. For instance, considering recent highly innovative methods, specifically in communication field, developed for design, manufacturing and exploiting dish antenna for specific cases, cooperation of other science and technology experts, like civil engineers, is also necessary. In this way, more delicate design procedure in order to satisfy communication requirement, is achieved. So far, no specific investigation about aforementioned subject, especially the effect of soil-structure interaction (SSI in analysing the seismic behaviour of communication large dish antennas has been conducted in Iran. In this paper, with the aim of investigating the effect of SSI on seismic behavior of pedestal, first an acceptable range for antenna displacement – as the most important parameter in pedestal structure for antenna – in both operational and survival states, has been calculated numerically based on generic formula. Secondly, the modelling of the whole pedestal-structure system has been modelled subjected to the associated loads and other primary conditions. This procedure has been performed once without considering the SSI and once more with it. Comparison of the obtained results shows that considering the SSI would impress the output results with a difference rate more than 50% and 600% respectively at survival and operational condition.

  6. High Efficiency, Low Cost Parabolic Dish System for Cogeneration of Electricity and Heat

    Chayet, Haim; Lozovsky, Ilan; Kost, Ori; Loeckenhoff, Ruediger; Rasch, Klaus-Dieter

    2010-10-01

    Highly efficient combined heat and power generating system based on CPV technology using unique dish design consisting of multiple simple flat mirrors mounted on a plastic parabolic surface. The dish of total aperture area of 11 m2 focuses 10.3 kWp onto a heat and electricity generating receiver. The receiver comprises a water cooled, dense triple junction cell array of 176 cm2 aperture area. A unique arrangement of the cells compensates for the non-uniformity of the reflected flux. Depending on the flow rate, the temperature of the hot water can be adjusted to suit from temperatures for domestic use, to temperatures suited for process heat. The output of 2.3 kWp electrical and 5.5 kWp thermal power from one dish system represent 20 to 21% electrical and 50% thermal conversion efficiency adding to 70% overall system efficiency.

  7. Problems of method of technology assessment. A methodological analysis; Methodenprobleme des Technology Assessment; Eine methodologische Analyse

    Zimmermann, V

    1993-03-01

    The study undertakes to analyse the theoretical and methodological structure of Technology Assessment (TA). It is based on a survey of TA studies which provided an important condition for theoreticall sound statements on methodological aspects of TA. It was established that the main basic theoretical problems of TA are in the field of dealing with complexity. This is also apparent in the constitution of problems, the most elementary and central approach of TA. Scientifically founded constitution of problems and the corresponding construction of models call for interdisciplinary scientific work. Interdisciplinarity in the TA research process is achieved at the level of virtual networks, these networks being composed of individuals suited to teamwork. The emerging network structures have an objective-organizational and an ideational basis. The objective-organizational basis is mainly the result of team composition and the external affiliations of the team members. The ideational basis of the virtual network is represented by the team members` mode of thinking, which is individually located at a multidisciplinary level. The theoretical `skeleton` of the TA knowledge system, which is represented by process knowledge based linkage structures, can be generated and also processed in connection with the knowledge on types of problems, areas of analysis and procedures to deal with complexity. Within this process, disciplinary knowledge is a necessary but not a sufficient condition. Metatheoretical and metadisciplinary knowledge and the correspondingly processes complexity of models are the basis for the necessary methodological awareness, that allows TA to become designable as a research procedure. (orig./HP) [Deutsch] Die Studie stellt sich die Aufgabe, die theoretische und methodische Struktur des Technology Assessment (TA) zu analysieren. Sie fusst auf Erhebungen, die bei Technology-Assessment-Studien vorgenommen wurden und die wesentliche Voraussetzungen fuer

  8. Design, Analysis and Optimization of a Solar Dish/Stirling System

    Seyyed Danial Nazemi

    2016-02-01

    Full Text Available In this paper, a mathematical model by which the thermal and physical behavior of a solar dish/Stirling system was investigated, then the system was designed, analysed and optimized. In this regard, all of heat losses in a dish/Stirling system were calculated, then, the output net-work of the Stirling engine was computed, and accordingly, the system efficiency was worked out. These heat losses include convection and conduction heat losses, radiation heat losses by emission in the cavity receiver, reflection heat losses of solar energy in the parabolic dish, internal and external conduction heat losses, energy dissipation by pressure drops, and energy losses by shuttle effect in displacer piston in the Stirling engine. All of these heat losses in the parabolic dish, cavity receiver and Stirling engine were calculated using mathematical modeling in MatlabTM software. For validation of the proposed model, a 10 kW solar dish/Stirling system was designed and the simulation results were compared with the Eurodish system data with a reasonable degree of agreement. This model is used to investigate the effect of geometric and thermodynamic parameters including the aperture diameter of the parabolic dish and the cavity receiver, and the pressure of the compression space of the Stirling engine, on the system performance. By using the PSO method, which is an intelligent optimization technique, the total design was optimized and the optimal values of decision-making parameters were determined. The optimization has been done in two scenarios. In the first scenario, the optimal value of each designed parameter has been changed when the other parameters are equal to the designed case study parameters. In the second scenario, all of parameters were assumed in their optimal values. By optimization of the modeled dish/Stirling system, the total efficiency of the system improved to 0.60% in the first scenario and it increased from 21.69% to 22.62% in the second

  9. International off-grid market assessment for dish/Stirling systems

    Lilienthal, P.; Campbell, K.

    1998-01-01

    Several features of dish/Stirling technology offer potential advantages for off-grid power generation. Dish/Stirling technology's size, modularity, the ease with which it might be hybridized with a storable fuel, the elimination of batteries and inverters, and the production of pure sine-wave AC power without a diesel all indicate that a reliable dish/Stirling module could fit well into an off-grid electrification scheme. At the same time, a combination of factors makes success in off-grid applications difficult, regardless of the technology under consideration. Obstacles include consumer expectations (formed by a long history of subsidies) that electricity should be cheap, existing support infrastructure, and the economic resources of rural communities. Cost is always a factor, but reliability and access to parts and service have been more significant barriers so far in the establishment of renewables. This paper summarizes a much more extensive market assessment. Initial research indicates that a reliable 25 kW dish/Stirling system with reasonable servicing requirements could compete well with other off-grid power systems at a cost considered achievable at early production levels ($3,500 per kW). However, by itself the off-grid power market in regions with adequate solar insolation and inviting political regimes does not justify an adequate scale of production. It is estimated that the aggregate market in five of the largest and most promising countries for which adequate information was available could be 23,000 to 38,000 units of 25 kW dish/Stirling systems. Including the rest of the developing world could more than double this number. However, at a reasonable initial market penetration rate of 1% per year this market is not sufficient, by itself, for the mass production rates required to achieve the necessary economies of scale

  10. An Automatic High Efficient Method for Dish Concentrator Alignment

    Yong Wang

    2014-01-01

    for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our method.

  11. A parametric investigation on a solar dish-Stirling system

    Gholamalizadeh, Ehsan; Chung, Jae Dong

    2018-06-01

    The aim of this study is to analyze the performance of a solar dish-Stirling system. A mathematical model for the overall thermal efficiency of the solar-powered high-temperature-differential dish-Stirling engine is described. This model takes into account pressure losses due to fluid friction which is internal to the engine, mechanical friction between the moving parts, actual heat transfer includes the effects of both internal and external irreversibilities of the cycle and finite regeneration processes time. Validation was done through comparison with the actual power output of the "EuroDish" system. Moreover, the effects of dish diameter and working fluid on the performance of the system were studied. An increase of about 7.2% was observed for the power output using hydrogen as the working fluid rather than helium. Also, the focal distance for any diameter of dish was calculated.

  12. Comparative analyses of seven technologies to facilitate the integration of fluctuating renewable energy sources

    Mathiesen, Brian Vad; Lund, Henrik

    2009-01-01

    An analysis of seven different technologies is presented. The technologies integrate fluctuating renewable energy sources (RES) such as wind power production into the electricity supply, and the Danish energy system is used as a case. Comprehensive hour-by-hour energy system analyses are conducted...... of a complete system meeting electricity, heat and transport demands, and including RES, power plants, and combined heat and power production (CHP) for district heating and transport technologies. In conclusion, the most fuel-efficient and least-cost technologies are identified through energy system...

  13. Economic performance of the SCE Stirling dish

    Stone, K.W.; Lopez, C.W.; McAlister, R.E.

    1993-01-01

    In 1982 McDonnell Douglas Aerospace Space System (MDA-SS) and United Stirling AB of Sweden formed a joint venture to develop and market a solar Stirling dish unit. Eight modules were built and extensively tested from 1984 to 1988. Power production and daily energy-conversion efficiency as determined by field testing have been characterized and modeled in a computer program. Included in this simulation are models of mirror soiling rate, wind spillage loss, mirror washing and other maintenance outage time, operation and maintenance (O and M) costs and other cost models. An economic model of a hybrid (combustion) receiver has been included in the simulation for illustrating the value of using solar energy when available and other fuels such as methane, natural gas, hydrogen, etc. when solar energy is not available or adequate. This paper describes the simulation and presents comparisons of the simulation to test data. The simulation also estimates both the O and M expenses and levelized energy costs for different production volumes

  14. Economic performance of the SCE Stirling dish

    Stone, K.W.; Lopez, C.W.; McAlister, R.E.

    1995-01-01

    In 1982 McDonnell Douglas Aerospace (MDA) and United Stirling AB (USAB) of Sweden formed a joint venture to develop and market a solar Stirling dish system. Eight modules were built and extensively tested from 1984 to 1988. Power production and daily energy-conversion efficiency as determined by field testing were characterized and modeled into a computer program. Included in this simulation are models of mirror soiling rate, wind spillage loss, mirror washing, and other maintenance outage time, operation and maintenance (O and M) costs, and equipment purchase cost. An economic model of a hybrid (combustion) receiver has been included in the simulation for illustrating the value of using solar energy when available and other fuels such as methane, natural gas, hydrogen, etc. when solar energy is not available or adequate. This paper describes the simulation and presents comparisons of the simulation to test data. The simulation also estimates both the O and M expenses and levelized energy costs for different production volumes

  15. Energy system analyses of the marginal energy technology in life cycle assessments

    Mathiesen, B.V.; Münster, Marie; Fruergaard, Thilde

    2007-01-01

    in historical and potential future energy systems. Subsequently, key LCA studies of products and different waste flows are analysed in relation to the recom- mendations in consequential LCA. Finally, a case of increased waste used for incineration is examined using an energy system analysis model......In life cycle assessments consequential LCA is used as the “state-of-the-art” methodology, which focuses on the consequences of decisions made in terms of system boundaries, allocation and selection of data, simple and dynamic marginal technology, etc.(Ekvall & Weidema 2004). In many LCA studies...... marginal technology? How is the marginal technology identified and used today? What is the consequence of not using energy system analy- sis for identifying the marginal energy technologies? The use of the methodology is examined from three angles. First, the marginal electricity technology is identified...

  16. Design methodologcal analyses as a tool for learning about technological developments in industrial settings

    Vries, de M.J.; Blandow, D.; Dyrenfurth, M.J.

    1995-01-01

    Design processes in industry are influenced by scientific, technological, market, political/juridical and aesthetical factors. In design methodological analyses these factors and their impact on the way a chain of designs is developed are studied. In a piecemeal rationality insight into the

  17. Technology images and concepts of technology in transition. An analysis in the philosophy of technology and general technology; Technikbilder und Technikkonzepte im Wandel. Eine technikphilosophische und allgemeintechnische Analyse

    Banse, G. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (DE). Inst. fuer Technikfolgen-Abschaetzung und Systemanalyse (ITAS); Meier, B. [Potsdam Univ. (Germany). Inst. fuer Arbeitslehre/Technik; Wolffgramm, H. (eds.)

    2002-02-01

    possessing general education in the area of technology, much attention is devoted to the typical ways of thinking and working in technology and the technical sciences. (orig.) [German] Dieser Band enthaelt Beitraege, die aus dem Fachgespraech 'Technikbilder und Technikkonzepte im Wandel - eine technikphilosophische und allgemeintechnische Analyse' hervorgingen. Dieses Fachgespraech fand am 06. Oktober 2000 im Paedagogischen Landesinstitut Brandenburg in Ludwigsfelde-Struveshof statt und wurde in Zusammenarbeit von Forschungszentrum Karlsruhe, Institut fuer Technikfolgenabschaetzung und Systemanalyse, Universitaet Potsdam, Institut fuer Arbeitslehre/Technik, und Professor Horst Wolffgramm, Frankfurt (Oder), konzipiert und organisiert. Anliegen des Fachgespraechs war es, Positionen der Technikphilosophie, der Allgemeinen Technikwissenschaft, der Technikgeschichte und der Technikdidaktik zur 'Konzeptualisierung' des Technischen als Grundlage fuer das generelle Verstaendnis von Technik bzw. eines wissenschaftlich fundierten 'Technikbildes' zusammenzutragen, zu vergleichen, aufeinander zu beziehen und fuer die curriculare Arbeit im Rahmen der Konzeptionierung einer allgemeinen technischen Bildung in allen Schulstufen nutzbar zu machen. Die Beitraege sind entsprechend den zwei Schwerpunkten der Tagung gruppiert: Einerseits geht es um Bestimmungen bezueglich eines zeitgemaessen Technikbegriffs ('Technikbild'). Hier gilt es auch historisch-genetisch den Technikwandel zu charakterisieren und so die Technik als Menschenwerk, als wesentliches Element unserer Kultur zu erschliessen. Dabei muss es zugleich auch gelingen, zukuenftige Entwicklungen zu prognostizieren bzw. moegliche Entwicklungspfade sichtbar zu machen, um den Wandel durch Basisinnovationen zu erfassen. Auf dieser Basis werden dann zweitens, gestuetzt auf die Bildungstheorie, Konsequenzen fuer eine zukunftsorientierte technische Allgemeinbildung fuer alle Schuelerinnen und Schueler

  18. Hygienic status assessment of dish washing waters, utensils, hands ...

    Hygienic status assessment of dish washing waters, utensils, hands and pieces of money from street food processing sites in Ouagadougou (Burkina Faso). N Barro, AR Bello, A Savadogo, CAT Ouattara, AJ Iiboudo, AS Traoré ...

  19. Mechanical design of a low cost parabolic solar dish concentrator

    Hamza Hijazi

    2016-03-01

    Full Text Available The objective of this research was to design a low cost parabolic solar dish concentrator with small-to moderate size for direct electricity generation. Such model can be installed in rural areas which are not connected to governmental grid. Three diameters of the dish; 5, 10 and 20 m are investigated and the focal point to dish diameter ratio is set to be 0.3 in all studied cases. Special attention is given to the selection of the appropriate dimensions of the reflecting surfaces to be cut from the available sheets in the market aiming to reduce both cutting cost and sheets cost. The dimensions of the ribs and rings which support the reflecting surface are optimized in order to minimize the entire weight of the dish while providing the minimum possible total deflection and stresses in the beams. The study applies full stress analysis of the frame of the dish using Autodesk Inventor. The study recommends to use landscape orientation for the reflective facets and increase the ribs angle and the distance between the connecting rings. The methodology presented is robust and can be extended to larger dish diameters.

  20. Computational methods, tools and data for nuclear analyses of fusion technology systems

    Fischer, U.

    2006-01-01

    An overview is presented of the Research and Development work conducted at Forschungszentrum Karlsruhe in co-operation with other associations in the framework of the European Fusion Technology Programme on the development and qualification of computational tools and data for nuclear analyses of Fusion Technology systems. The focus is on the development of advanced methods and tools based on the Monte Carlo technique for particle transport simulations, and the evaluation and qualification of dedicated nuclear data to satisfy the needs of the ITER and the IFMIF projects. (author)

  1. Generación de energía eléctrica en la edificación mediante tecnología de disco Stirling =Electrical energy generation in building by means of Stirling dish technology

    Carlos Morón

    2017-08-01

    Full Text Available La creciente demanda de energía acompañada de los elevados niveles de emisión de gases contaminantes a la atmosfera hace patente la necesidad de encontrar nuevos sistemas de producción de energía. Una de las posibles alternativas se encuentra en la energía solar de concentración, y más concretamente en la tecnología termosolar con motor Stirling que alcanza unos niveles de rendimiento muy superiores a la energía solar fotovoltaica en cuanto a producción de energía eléctrica. En este trabajo se muestra el diseño y la caracterización de un prototipo de captador paraboloidal con motor Stirling, que permite obtener datos reales del funcionamiento de este tipo de sistemas. Esto permitirá modelizar de manera real el comportamiento esperado de equipos comerciales reales antes de abordar su implantación en edificios y viviendas unifamiliares. Abstract The increasing demand for energy accompanied by high level of emission of the contaminating gases into the atmosphere underscores the need to find new energy production systems. One of the possible alternatives is concentrating solar power and, more specifically, solar thermal technology with a Stirling engine that reaches higher performance levels than photovoltaic solar energy in terms of electricity generation. This paper shows the design and characterization of a prototype paraboloidal collector with a Stirling engine that allows obtaining real data of this type of systems functioning. This will allow modelling in a real way of expected performance of real commercial devices before approaching their introduction in buildings and single-family houses.

  2. Occurrence of heterocyclic amines in several home-cooked meat dishes of the Spanish diet.

    Busquets, R; Bordas, M; Toribio, F; Puignou, L; Galceran, M T

    2004-03-25

    Heterocyclic amines (HAs) were determined in several of the most frequently eaten meat dishes in Spain such as fried beef hamburger, fried pork loin, fried chicken breast, fried pork sausages, griddled chicken breast, griddled lamb steak and griddled beef steak. All of the products tested were household cooked. The HAs were analysed in the selected meat dishes using an analytical method based on solid-phase extraction followed by liquid chromatography coupled to tandem mass spectrometry. DMIP, MeIQx, 4,8-DiMeIQx, Norharman, Harman, PhIP, Trp-P-1, AalphaC and MeAalphaC were the amines most frequently found at concentrations of up to 47 ng g(-1) of cooked meat. Glu-P-2, IQ, MeIQ, Glu-P-1, 7,8-DiMeIQx and Trp-P-2 were only found in a few of the meat dishes and their concentrations were lower than 1 ng g(-1) of cooked meat. The highest amounts of HAs, especially PhIP and DMIP, were formed in fried chicken breast and the lowest were formed in fried beef hamburger and in fried pork sausages. Daily intake of HAs in Spain was estimated at 606 ng of mutagenic HAs per capita and day, DMIP and PhIP being the main contributors.

  3. [Meta-analyses on measurement precision of non-invasive hemodynamic monitoring technologies in adults].

    Pestel, G; Fukui, K; Higashi, M; Schmidtmann, I; Werner, C

    2018-06-01

    An ideal non-invasive monitoring system should provide accurate and reproducible measurements of clinically relevant variables that enables clinicians to guide therapy accordingly. The monitor should be rapid, easy to use, readily available at the bedside, operator-independent, cost-effective and should have a minimal risk and side effect profile for patients. An example is the introduction of pulse oximetry, which has become established for non-invasive monitoring of oxygenation worldwide. A corresponding non-invasive monitoring of hemodynamics and perfusion could optimize the anesthesiological treatment to the needs in individual cases. In recent years several non-invasive technologies to monitor hemodynamics in the perioperative setting have been introduced: suprasternal Doppler ultrasound, modified windkessel function, pulse wave transit time, radial artery tonometry, thoracic bioimpedance, endotracheal bioimpedance, bioreactance, and partial CO 2 rebreathing have been tested for monitoring cardiac output or stroke volume. The photoelectric finger blood volume clamp technique and respiratory variation of the plethysmography curve have been assessed for monitoring fluid responsiveness. In this manuscript meta-analyses of non-invasive monitoring technologies were performed when non-invasive monitoring technology and reference technology were comparable. The primary evaluation criterion for all studies screened was a Bland-Altman analysis. Experimental and pediatric studies were excluded, as were all studies without a non-invasive monitoring technique or studies without evaluation of cardiac output/stroke volume or fluid responsiveness. Most studies found an acceptable bias with wide limits of agreement. Thus, most non-invasive hemodynamic monitoring technologies cannot be considered to be equivalent to the respective reference method. Studies testing the impact of non-invasive hemodynamic monitoring technologies as a trend evaluation on outcome, as well as

  4. A Compendium of Solar Dish/Stirling Technology

    1994-01-01

    systems and Plataforma Solar in Almeria, Spain, with the goal being plans to produce fourteen 7.5-kWe systems for testing to test the system’s long-term...the sun is not a point source, its rays 21 Chapter 3 (a) (b) - N Mounting Ring and CollaraI/ / I/\\ I / Virtual Exit I / Target S• Entrance I 0 L...tptical \\ I Real Exit / Virtual Target \\ Aperture\\ / Cooling \\ / I Coils N - Focal - - - - " Plane 4. Figure 3-2. A secondary concentrator with side view (a

  5. Advanced Materials, Technologies, and Complex Systems Analyses: Emerging Opportunities to Enhance Urban Water Security.

    Zodrow, Katherine R; Li, Qilin; Buono, Regina M; Chen, Wei; Daigger, Glen; Dueñas-Osorio, Leonardo; Elimelech, Menachem; Huang, Xia; Jiang, Guibin; Kim, Jae-Hong; Logan, Bruce E; Sedlak, David L; Westerhoff, Paul; Alvarez, Pedro J J

    2017-09-19

    Innovation in urban water systems is required to address the increasing demand for clean water due to population growth and aggravated water stress caused by water pollution, aging infrastructure, and climate change. Advances in materials science, modular water treatment technologies, and complex systems analyses, coupled with the drive to minimize the energy and environmental footprints of cities, provide new opportunities to ensure a resilient and safe water supply. We present a vision for enhancing efficiency and resiliency of urban water systems and discuss approaches and research needs for overcoming associated implementation challenges.

  6. Advanced computational tools and methods for nuclear analyses of fusion technology systems

    Fischer, U.; Chen, Y.; Pereslavtsev, P.; Simakov, S.P.; Tsige-Tamirat, H.; Loughlin, M.; Perel, R.L.; Petrizzi, L.; Tautges, T.J.; Wilson, P.P.H.

    2005-01-01

    An overview is presented of advanced computational tools and methods developed recently for nuclear analyses of Fusion Technology systems such as the experimental device ITER ('International Thermonuclear Experimental Reactor') and the intense neutron source IFMIF ('International Fusion Material Irradiation Facility'). These include Monte Carlo based computational schemes for the calculation of three-dimensional shut-down dose rate distributions, methods, codes and interfaces for the use of CAD geometry models in Monte Carlo transport calculations, algorithms for Monte Carlo based sensitivity/uncertainty calculations, as well as computational techniques and data for IFMIF neutronics and activation calculations. (author)

  7. Transfer of fibroblast sheets cultured on thermoresponsive dishes with membranes.

    Kawecki, Marek; Kraut, Małgorzata; Klama-Baryła, Agnieszka; Łabuś, Wojciech; Kitala, Diana; Nowak, Mariusz; Glik, Justyna; Sieroń, Aleksander L; Utrata-Wesołek, Alicja; Trzebicka, Barbara; Dworak, Andrzej; Szweda, Dawid

    2016-06-01

    In cell or tissue engineering, it is essential to develop a support for cell-to-cell adhesion, which leads to the generation of cell sheets connected by extracellular matrix. Such supports must be hydrophobic and should result in a detachable cell sheet. A thermoresponsive support that enables the cultured cell sheet to detach using only a change in temperature could be an interesting alternative in regenerative medicine. The aim of this study was to evaluate plates covered with thermoresponsive polymers as supports for the formation of fibroblast sheets and to develop a damage-free procedure for cell sheet transfer with the use of membranes as transfer tools. Human skin fibroblasts were seeded on supports coated with a thermoresponsive polymer: commercial UpCell™ dishes (NUNC™) coated with thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) and dishes coated with thermoresponsive poly(tri(ethylene glycol) monoethyl ether methacrylate) (P(TEGMA-EE)). Confluent fibroblast sheets were effectively cultured and harvested from both commercial PNIPAM-coated dishes and laboratory P(TEGMA-EE)-coated dishes. To transfer a detached cell sheet, two membranes, Immobilon-P(®) and SUPRATHEL(®), were examined. The use of SUPRATHEL for relocating the cell sheets opens a new possibility for the clinical treatment of wounds. This study established the background for implementing thermoresponsive supports for transplanting in vitro cultured fibroblasts.

  8. Radiotreatment of dishes cooked : Royal cutlets of chickens

    Bousselmi, Mehrez

    2006-01-01

    The cooked dishes often present themselves as the complex products of microbiological, biochemival view point and organoleptic.However, the demand of the local and international market stops showing a tendency toward use increased of these cooked dishes of which problems to get round are very delicate. The ionization can be an alternative of conservation since it is characterized bye one fashion of action fundamentally different of the classic techniques: it is about exposing during a determined length, of the wrapped food commodities or in a jumble to doses of ionising radiance carefully controlled in order to get the sought-after effect. The irradiation showed a big efficiency therefore on the plan microbiology.Indeed the dose 1 KGy destroyed all present microorganisms in dishes cooked pasteurized. whereas, for dishes cooked non pasteurized, a dose of 2 KGy destroyed completely the flora of contamination. Besides, the irradiation entails a light reduction of the biochemical composition, while keeping qualities intact organoleptic for all analyzed samples. As a conclusion, the irradiation increases the length of conservation, what confirms the reliability of such a process, in addition of his/her/its weak energizing cost. (author)

  9. Ankylosant spondylitis association and diffuse idiopathic skeletal hyperostosis (DISH)

    Medina, Yimi; Restrepo Suarez, Jose Felix; Calvo Paramo, Enrique

    2000-01-01

    We are presenting a 66 year-old patient complaining of low back pain for the last 3 months and cervical pain for the last 45 days, Review of systems showed long standing lumbar and cervical stiffness, Radiological studies were compatible with ankylosing spondylitis and DISH (Diffuse idiopathic Skeletal Hyperostosis). Associations of those diseases are uncommon and reported only few times in the literature

  10. Analysing the Effects of Flood-Resilience Technologies in Urban Areas Using a Synthetic Model Approach

    Reinhard Schinke

    2016-11-01

    Full Text Available Flood protection systems with their spatial effects play an important role in managing and reducing flood risks. The planning and decision process as well as the technical implementation are well organized and often exercised. However, building-related flood-resilience technologies (FReT are often neglected due to the absence of suitable approaches to analyse and to integrate such measures in large-scale flood damage mitigation concepts. Against this backdrop, a synthetic model-approach was extended by few complementary methodical steps in order to calculate flood damage to buildings considering the effects of building-related FReT and to analyse the area-related reduction of flood risks by geo-information systems (GIS with high spatial resolution. It includes a civil engineering based investigation of characteristic properties with its building construction including a selection and combination of appropriate FReT as a basis for derivation of synthetic depth-damage functions. Depending on the real exposition and the implementation level of FReT, the functions can be used and allocated in spatial damage and risk analyses. The application of the extended approach is shown at a case study in Valencia (Spain. In this way, the overall research findings improve the integration of FReT in flood risk management. They provide also some useful information for advising of individuals at risk supporting the selection and implementation of FReT.

  11. The kinematic Stirling engine as an energy conversion subsystem for paraboloidal dish solar thermal plants

    Bowyer, J. M.

    1984-01-01

    The potential of a suitably designed and economically manufactured Stirling engine as the energy conversion subsystem of a paraboloidal dish-Stirling solar thermal power module was estimated. Results obtained by elementary cycle analyses were shown to match quite well the performance characteristics of an advanced kinematic Stirling engine, the United Stirling P-40, as established by current prototypes of the engine and by a more sophisticated analytic model of its advanced derivative. In addition to performance, brief consideration was given to other Stirling engine criteria such as durability, reliability, and serviceability. Production costs were not considered here.

  12. Outsourcing medical data analyses: can technology overcome legal, privacy, and confidentiality issues?

    Brumen, Bostjan; Heričko, Marjan; Sevčnikar, Andrej; Završnik, Jernej; Hölbl, Marko

    2013-12-16

    Medical data are gold mines for deriving the knowledge that could change the course of a single patient's life or even the health of the entire population. A data analyst needs to have full access to relevant data, but full access may be denied by privacy and confidentiality of medical data legal regulations, especially when the data analyst is not affiliated with the data owner. Our first objective was to analyze the privacy and confidentiality issues and the associated regulations pertaining to medical data, and to identify technologies to properly address these issues. Our second objective was to develop a procedure to protect medical data in such a way that the outsourced analyst would be capable of doing analyses on protected data and the results would be comparable, if not the same, as if they had been done on the original data. Specifically, our hypothesis was there would not be a difference between the outsourced decision trees built on encrypted data and the ones built on original data. Using formal definitions, we developed an algorithm to protect medical data for outsourced analyses. The algorithm was applied to publicly available datasets (N=30) from the medical and life sciences fields. The analyses were performed on the original and the protected datasets and the results of the analyses were compared. Bootstrapped paired t tests for 2 dependent samples were used to test whether the mean differences in size, number of leaves, and the accuracy of the original and the encrypted decision trees were significantly different. The decision trees built on encrypted data were virtually the same as those built on original data. Out of 30 datasets, 100% of the trees had identical accuracy. The size of a tree and the number of leaves was different only once (1/30, 3%, P=.19). The proposed algorithm encrypts a file with plain text medical data into an encrypted file with the data protected in such a way that external data analyses are still possible. The results

  13. Usages des technologies par les élèves professeurs : analyse à partir de questionnaires

    Philippe Le Borgne

    2005-01-01

    Full Text Available Cet article étudie l’appropriation et les usages des technologies chez les élèves professeurs français. La méthodologie utilisée est basée sur l’analyse de réponses à des questionnaires soumis aux professeurs stagiaires de quatre instituts universitaires de formation des maîtres. Les résultats obtenus tendent à prouver que les enseignants en formation sont aujourd’hui bien équipés et disposent de compétences réelles dans le cadre des usages personnels et professionnels en dehors de la classe. Cependant, il apparaît que ces compétences sont peu mobilisées dans le cadre des usages en classe.

  14. Using the ICF in economic analyses of Assistive Technology systems: methodological implications of a user standpoint.

    Schraner, Ingrid; De Jonge, Desleigh; Layton, Natasha; Bringolf, Jane; Molenda, Agata

    2008-01-01

    This paper identifies key methodological issues for economic analyses of costs and effectiveness of Assistive Technology (AT) systems based on the International Classification of Functioning, Disability and Health (ICF). Following the biopsychosocial model of the ICF, the paper explores the consequences for cost-effectiveness analyses of AT systems when a user centred approach is taken. In so doing, the paper questions the fiction of neutrality in economic analyses and discusses the distinction between weak and strong objectivity. Costs are measured as all resources used when providing a particular level of environmental facilitators and reducing environmental barriers for an AT user, while effectiveness is measured in terms of the resulting increase in activities and participation of the AT user. The ICF's fourth qualifier for activities and participation, which denotes performance without assistance is used to identify the additional performance achieved due to the particular environmental factors in the current situation (first qualifier). A fifth qualifier for activities and participation is introduced to denote performance with optimal assistance, and the fourth qualifier is then again used to identify the increase in activities and participation due to the environmental factors in the situation with optimal assistance. The effectiveness that an AT user achieves in his or her current situation can be compared with the effectiveness he or she could achieve when provided with what is considered an optimal AT system based on current technologies and user priorities. This comparison throws into sharp relief the role of AT systems as well as of universal design (UD) in reducing environmental barriers for AT users in a way that is cost-effective for society as a whole. Cost-effectiveness analysis based on the ICF can provide powerful economic evidence for how best to allocate existing funding for AT systems. We can identify three particular scenarios in which clear

  15. To What Extent Do Biology Textbooks Contribute to Scientific Literacy? Criteria for Analysing Science-Technology-Society-Environment Issues

    Calado, Florbela M.; Scharfenberg, Franz-Josef; Bogner, Franz X.

    2015-01-01

    Our article proposes a set of six criteria for analysing science-technology-society-environment (STSE) issues in regular textbooks as to how they are expected to contribute to students' scientific literacy. We chose genetics and gene technology as fields prolific in STSE issues. We derived our criteria (including 26 sub-criteria) from a literature…

  16. Development status of the PDC-1 Parabolic Dish Concentrator

    Thostesen, T.; Soczak, I. F.; Pons, R. L.

    1982-01-01

    The status of development of the 12 m diameter parabolic dish concentrator which is planned for use with the Small Community Solar Thermal Power System. The PDC-1 unit features the use of plastic reflector film bonded to structural plastic gores supported by front-bracing steel ribs. An elevation-over-azimuth mount arrangement is employed, with a conventional wheel-and-track arrangement; outboard trunnions permit the dish to be stored in the face down position, with the added advantage of easy access to the power conversion assembly. The control system is comprised of a central computer (LSI 1123), a manual control panel, a concentrator control unit, two motor controllers, a Sun sensor, and two angular position resolvers. The system is designed for the simultaneous control of several concentrators. The optical testing of reflective panels is described.

  17. Searching for WISPy cold dark matter with a dish antenna

    Horns, Dieter [Hamburg Univ. (Germany). Inst. fuer Experimentalphysik; Jaeckel, Joerg [Heidelberg Univ. (Germany). Inst. fuer Theoretische Physik; Durham Univ. (United Kingdom). Inst. for Particle Physics Phenomenology; Lindner, Axel; Ringwald, Andreas [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Lobanov, Andrei [Max-Planck-Institut fuer Radioastronomie, Bonn (Germany); Redondo, Javier [Muenchen Univ. (Germany). Arnold Sommerfeld Center; Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2012-12-15

    The cold dark matter of the Universe may be comprised of very light and very weakly interacting particles, so-called WISPs. Two prominent examples are hidden photons and axion-like particles. In this note we propose a new technique to sensitively search for this type of dark matter with dish antennas. The technique is broadband and allows to explore a whole range of masses in a single measurement.

  18. Overview of Submm Single Dish: From Observations to Useful Data

    Stanke, Thomas

    2018-03-01

    Observing with single dish telescopes at submillimetre wavelengths adds a number of challenges. The Earth's atmosphere not only absorbs the sky signal with varying amounts as a function of frequency and weather conditions, but it also emits a signal that is many orders of magnitude brighter than the astronomical signal one is interested in. Additional challenges come in the calibration and removal of certain instrumental effects. I will give an overview of present and planned submillimetre telescopes, instrument types, and observing strategies.

  19. Artificial neural networks approach on solar parabolic dish cooker

    Lokeswaran, S.; Eswaramoorthy, M.

    2011-01-01

    This paper presents heat transfer analysis of solar parabolic dish cooker using Artificial Neural Network (ANN). The objective of this study to envisage thermal performance parameters such as receiver plate and pot water temperatures of the solar parabolic dish cooker by using the ANN for experimental data. An experiment is conducted under two cases (1) cooker with plain receiver and (2) cooker with porous receiver. The Back Propagation (BP) algorithm is used to train and test networks and ANN predictions are compared with experimental results. Different network configurations are studied by the aid of searching a relatively better network for prediction. The results showed a good regression analysis with the correlation coefficients in the range of 0.9968-0.9992 and mean relative errors (MREs) in the range of 1.2586-4.0346% for the test data set. Thus ANN model can successfully be used for the prediction of the thermal performance parameters of parabolic dish cooker with reasonable degree of accuracy. (authors)

  20. Numerical and experimental dosimetry of petri dish exposure setups

    Burkhardt, M.; Pokovic, K.; Gnos, M.; Schmid, T.; Kuster, N. [Swiss Federal Inst. of Tech., Zurich (Switzerland)

    1996-12-31

    Crawford TEM cells are often used to exposure cell cultures or small animals in order to study the effects caused by high-frequency fields. They are self-contained, easy-to-use setups that provide a rather homogeneous field distribution in a large area around its center, corresponding approximately to far-field conditions. However, a number of conditions must be met if such TEM cells are intended to be used for in vitro experiments. For instance, poor interaction with the incident field must be maintained to avoid significant field disturbances in the TEM cell. This is best achieved with E-polarization, i.e., when the E-field vector is normal to the investigated cell layer lining the bottom of a synthetic Petri dish. In addition, E-polarization provides the most homogeneous field distribution of all polarizations within the entire layer of cells. In this paper, the authors present a detailed dosimetric assessment for 60 and 100 mm Petri dishes as well as for a 48-well titer plate at 835 MHz. The dosimetry was performed by using numerical computations. The modeling and the simplifications are validated by a second numerical technique and by experimental measurements. For thin liquid layers, an approximation formula is provided with which the induced field strength for many other experiments conducted in Petri dishes can be assessed reliably.

  1. Technologies for forgeries of greek silver drachmas analysed by xrf and pixe

    Constantinescu, B.

    2002-01-01

    The analyses of source materials combined with analyses of archaeological objects could distinguish from pieces produced in different regions and periods. For coins, chemical differences that occur during preparation of alloys will affect the elemental composition and could be used for the identification of technologies and workshops and also to distinguish between originals and counterfeits. We illustrate with the case of Greek Apollonia and Dyrrhachium silver drachmas emitted by these old cities for Pompejus during the First Roman Civil War between Julius Caesar and Pompejus, coins found on the actual territory of Romania (ancient Dacia), probably used as bursaries to pay the Dacian mercenaries allied with Pompejus. To analyze the chemical composition of these coins, we used two methods: Am-241 gamma source based X-Ray Fluorescence (XRF) and in vacuum 3 MeV protons Particle Induced X-ray Emission (PIXE). XRF measurements were done with a spectrometer consisting of a 30 mCi Am-241 annular source, a vertical Si(Li) detector and a conventional electronic chain. For PIXE, we used 3 MeV protons (15-20 nA intensity on the sample using a pile-up rejector system) accelerated at Bucharest 8 MV High Voltage Tandem, a horizontal HPGE detector placed perpendicularly on the beam direction and a conventional electronic chain. Some special measurements on the edge of some coins (to identify plated exemplaires) were done using the ATOMKI Debrecen Van de Graaf 2 MeV protons microprobe, in the frame of European Action COST G1. We analysed approx. 300 drachmas. Five main categories were found: - original coins (similar to drachms emitted before the Civil War) with 97-99 percent silver, low (1-2 percent) copper content, -debased coins with silver content down to 70 percent and copper content from 5 to 25 percent, probably emitted due to inflation problem, normal phenomenon for an economy in war, -official (original dies) counterfeits from bronze (70 percent copper and 30 percent tin

  2. Sparking interest in restaurant dishes? Cognitive and affective processes underlying dish design and ecological origin. An fMRI study.

    Muñoz-Leiva, Francisco; Gómez-Carmona, Diego

    2018-06-14

    The objective of the current paper is to verify to what extent the presentation of a restaurant dish and the origin of its food provoke reactions in the consumer's brain during the visualization and the decision-making process, from an exploratory approach. The two independent variables singled out for study were whether the presentation was well or poorly presented and if the ingredients were ecological or non-ecological. The results applying the functional magnetic resonance image (fMRI) methodology reveal that well-presented dishes activate areas in the brain linked to the network of emotions indicating that the visualization in restaurant menus is not a purely cognitive and self-reflexive process but retains a strong affective component. Furthermore, the presence of this component is kept at the moment of choosing a dish, as observed by the activation of the gyrus cingulate, region linked to the regulatory processes of emotions. Hence, research ratifies the existence of an emotional factor during the entire process of decision-making carried out in a restaurant. Yet it is true that exposure to an ecological menu provokes activation of the medial frontal cortex, a region connected to higher reasoning and attention, suggesting that stimuli from well-presented dishes of ecological origin trigger neuronal responses related to high-level cognitive processes. The practical implications derived, along with its limitations and the future research opportunities, are interesting for both developing theory and also practice. Therefore, scholars are encouraged to further test some research proposals (e.g. moderating role of salubrity or simultaneously eye tracking method). Copyright © 2017. Published by Elsevier Inc.

  3. Exergy Analysis of a Pilot Parabolic Solar Dish-Stirling System

    Ehsan Gholamalizadeh

    2017-09-01

    Full Text Available Energy and exergy analyses were carried out for a pilot parabolic solar dish-Stirling System. The system was set up at a site at Kerman City, located in a sunny desert area of Iran. Variations in energy and exergy efficiency were considered during the daytime hours of the average day of each month in a year. A maximum collector energy efficiency and total energy efficiency of 54% and 12.2%, respectively, were predicted in July, while during the period between November and February the efficiency values were extremely low. The maximum collector exergy efficiency was 41.5% in July, while the maximum total exergy efficiency reached 13.2%. The values of energy losses as a percentage of the total losses of the main parts of the system were also reported. Results showed that the major energy and exergy losses occurred in the receiver. The second biggest portion of energy losses occurred in the Stirling engine, while the portion of exergy loss in the concentrator was higher compared to the Stirling engine. Finally, the performance of the Kerman pilot was compared to that of the EuroDish project.

  4. Operational data and thermodynamic modeling of a Stirling-dish demonstration installation in desert conditions

    Nilsson, Martin; Jamot, Jakob; Malm, Tommy

    2017-06-01

    To field test its Stirling-dish unit, Cleanergy AB of Sweden in Q1 2015 built a ten unit demo park in Dubai. The first STE (Solar Thermal Energy) generation of its Stirling genset, the C11S, had at its core an 11 kWel Stirling engine/generator combination. The genset was mated with a parabolic concentrator developed for the genset by a supplier. Local weather conditions in Dubai provide opportunities to test performance in an environment with high insolation and high ambient temperature. In addition, the conditions in Dubai are windy, salty, humid and dusty, historically challenging for solar technologies [1]. In Q1 2016 one of the C11S Stirling-dish units was replaced by the first prototype of Cleanergy's second generation Stirling genset, the Sunbox, and an in-house developed parabolic concentrator. Operational data from field testing during the spring of 2016 are presented and discussed and show the large performance improvement achieved with the Sunbox unit.

  5. Carbon Footprint Analyses of Mainstream Wastewater Treatment Technologies under Different Sludge Treatment Scenarios in China

    Chunyan Chai

    2015-03-01

    Full Text Available With rapid urbanization and infrastructure investment, wastewater treatment plants (WWTPs in Chinese cities are putting increased pressure on energy consumption and exacerbating greenhouse gas (GHG emissions. A carbon footprint is provided as a tool to quantify the life cycle GHG emissions and identify opportunities to reduce climate change impacts. This study examined three mainstream wastewater treatment technologies: Anaerobic–Anoxic–Oxic (A–A–O, Sequencing Batch Reactor (SBR and Oxygen Ditch, considering four different sludge treatment alternatives for small-to-medium-sized WWTPs. Following the life cycle approach, process design data and emission factors were used by the model to calculate the carbon footprint. Results found that direct emissions of CO2 and N2O, and indirect emissions of electricity use, are significant contributors to the carbon footprint. Although sludge anaerobic digestion and biogas recovery could significantly contribute to emission reduction, it was less beneficial for Oxygen Ditch than the other two treatment technologies due to its low sludge production. The influence of choosing “high risk” or “low risk” N2O emission factors on the carbon footprint was also investigated in this study. Oxygen Ditch was assessed as “low risk” of N2O emissions while SBR was “high risk”. The carbon footprint of A–A–O with sludge anaerobic digestion and energy recovery was more resilient to changes of N2O emission factors and control of N2O emissions, though process design parameters (i.e., effluent total nitrogen (TN concentration, mixed-liquor recycle (MLR rates and solids retention time (SRT and operation conditions (i.e., nitrite concentration are critical for reducing carbon footprint of SBR. Analyses of carbon footprints suggested that aerobic treatment of sludge not only favors the generation of large amounts of CO2, but also the emissions of N2O, so the rationale of reducing aerobic treatment and

  6. Variations in Nutrients Composition of Most Commonly Consumed Cassava (Manihot esculenta Mixed Dishes in South-Eastern Nigeria

    G. I. Davidson

    2017-01-01

    Full Text Available Variations in nutrient composition of most commonly consumed cassava (Manihot esculenta mixed dishes in South-eastern Nigeria were determined. Four communities were randomly selected from each of the five states in the South-east. Focus group discussions (FGD were conducted in each of the communities to determine commonly consumed foods and variations in recipes. 24-Hour dietary recall was conducted using 50 randomly selected households in those communities. Recipes collected during the FGD were standardized, prepared, and chemically analysed using standard methods. Data were analysed using descriptive statistics. Cassava-based dishes were the most commonly consumed in South-eastern Nigeria. Ninety-two percent of the study population ate cassava either in form of “fufu” (fermented cassava meal/garri (fermented and roasted cassava meal with soup or as “abacha” (tapioca salad. Commonly consumed soups were melon (Citrullus vulgaris seeds, “ora” (Pterocarpus soyauxii, and vegetable soups. Seven melon seed, six “ora,” and four vegetable soups and five “abacha” variations were identified. Except for vegetable soup, coefficient of variation for moisture was <10%, while large variations (19–71% were observed for energy and nutrients. These variations in cassava-based dishes need to be reflected in the country-specific food composition database to enable nutrient intake assessment or provision of dietary guidance using such food composition database as a reference material to be more effective.

  7. Water Content in the SW USA Mantle Lithosphere: FTIR Analysis of Dish Hill and Kilbourne Hole Pyroxenites

    Gibler, Robert; Peslier, Anne H.; Schaffer, Lillian Aurora; Brandon, Alan D.

    2014-01-01

    Kilbourne Hole (NM, USA) and Dish Hill (CA, USA) mantle xenoliths sample continental mantle in two different tectonic settings. Kilbourne Hole (KH) is located in the Rio Grande rift. Dish Hill (DH) is located in the southern Mojave province, an area potentially affected by subduction of the Farallon plate beneath North America. FTIR analyses were obtained on well characterized pyroxenite, dunite and wehrlite xenoliths, thought to represent crystallized melts at mantle depths. PUM normalized REE patterns of the KH bulk-rocks are slightly LREE enriched and consistent with those of liquids generated by 6% melting of a spinel peridotite source. Pyroxenite pyroxenes have no detectable water but one DH wehrlite, which bulk-rock is LREE enriched, has 4 ppm H2O in orthopyroxene and 2 Ga. The Farallon subduction appears to have enriched in water the southwestern United States lithospheric mantle further east than DH, beneath the Colorado plateau.

  8. Idea of Identification of Copper Ore with the Use of Process Analyser Technology Sensors

    Jurdziak, Leszek; Kaszuba, Damian; Kawalec, Witold; Król, Robert

    2016-10-01

    The Polish resources of the copper ore exploited by the KGHM S.A. underground mines are considered as one of the most complex in the world and - consequently - the most difficult to be processed. The ore consists of three lithology forms: dolomites, shales and sandstones but in different proportions which has a significant impact on the effectiveness of the grinding and flotation processes. The lithological composition of the ore is generally recognised in-situ but after being mined it is blended on its long way from various mining fields to the processing plant by the complex transportation system consisting of belt conveyors with numerous switching points, ore bunkers and shafts. Identification of the lithological composition of the ore being supplied to the processing plant should improve the adjustments of the ore processing machinery equipment aiming to decrease the specific processing (mainly grinding) energy consumption as well as increase the metal recovery. The novel idea of Process Analyser Technology (PAT) sensors - information carrying pellets, dropped into the transported or processed bulk material which can be read directly when needed - is investigated for various applications within the DISIRE project (a part of the SPIRE initiative, acting under the Horizon2020 framework program) and here is adopted for implementing the annotation the transported copper ore for the needs of ore processing plants control. The identification of the lithological composition of ore blended on its way to the processing plant can be achieved by an information system consisting of pellets that keep the information about the original location of the portions of conveyed ore, the digital, geological database keeping the data of in-situ lithology and the simulation models of the transportation system, necessary to evaluate the composition of the blended ore. The assumptions of the proposed solution and the plan of necessary in-situ tests (with the special respect to harsh

  9. Spondyloarthritis, diffuse idiopathic skeletal hyperostosis (DISH) and chondrocalcinosis.

    Armas, Jácome Brugues; Couto, Ana Rita; Bettencourt, Bruno Filipe

    2009-01-01

    The authors describe the main clinical and radiological findings of common enthesopathic disorders-spondylarthritis (SpA), chondrocalcinosis/calcium pyrophosphate dehydrate crystal deposition disease (CPPD CDD) and diffuse idiopathic skeletal hyperostosis (DISH), stressing similarities and differences which may help in the differential diagnosis. They emphasize the clinical presentation of the "pseudoankylosing spondylitis" forms of CPPD CDD. They also review the most relevant genes and molecular mechanisms associated with these conditions and with another enthesopathic disorder with high prevalence in the Japanese population-ossification of the posterior longitudinal ligament (OPLL).

  10. Gods, Germs, and Petri Dishes: Toward a Nonsecular Medical Anthropology.

    Roberts, Elizabeth F S

    2016-01-01

    This commentary calls on medical anthropology to become programmatically non-secular. Despite recent anthropological critiques of secularity, within and outside of anthropology, most contemporary medical anthropologists continue to leave deities and religiosity out of their examinations of healing practices, especially in their accounts of biomedicine. Through a critical, relational constructionist lens, which traces how all entities are both constructed and real, a non-secular medical anthropology would insist that when deities are part of medical practice, they are integral to analysis. Importantly then, within the symmetrical nature of this same constructionist lens, biomedical entities like germs and petri dishes need to be accounted for just as much as deities.

  11. Overview of software development at the parabolic dish test site

    Miyazono, C. K.

    1985-01-01

    The development history of the data acquisition and data analysis software is discussed. The software development occurred between 1978 and 1984 in support of solar energy module testing at the Jet Propulsion Laboratory's Parabolic Dish Test Site, located within Edwards Test Station. The development went through incremental stages, starting with a simple single-user BASIC set of programs, and progressing to the relative complex multi-user FORTRAN system that was used until the termination of the project. Additional software in support of testing is discussed including software in support of a meteorological subsystem and the Test Bed Concentrator Control Console interface. Conclusions and recommendations for further development are discussed.

  12. Functions of Innovation Systems : A new approach for analysing technological change

    Hekkert, M.P.; Suurs, R.A.A.; Negro, Simona; Kuhlmann, Stefan; Smits, R.E.H.M.

    2007-01-01

    The central idea of this paper is that innovation systems are a very important determinant of technological change. We describe that the emergence of a new innovation system and changes in existing innovation systems co-evolve with the process of technological change. Therefore, it is necessary to

  13. Evaluation of the comprehensive palatability of Japanese sake paired with dishes by multiple regression analysis based on subdomains.

    Nakamura, Ryo; Nakano, Kumiko; Tamura, Hiroyasu; Mizunuma, Masaki; Fushiki, Tohru; Hirata, Dai

    2017-08-01

    Many factors contribute to palatability. In order to evaluate the palatability of Japanese alcohol sake paired with certain dishes by integrating multiple factors, here we applied an evaluation method previously reported for palatability of cheese by multiple regression analysis based on 3 subdomain factors (rewarding, cultural, and informational). We asked 94 Japanese participants/subjects to evaluate the palatability of sake (1st evaluation/E1 for the first cup, 2nd/E2 and 3rd/E3 for the palatability with aftertaste/afterglow of certain dishes) and to respond to a questionnaire related to 3 subdomains. In E1, 3 factors were extracted by a factor analysis, and the subsequent multiple regression analyses indicated that the palatability of sake was interpreted by mainly the rewarding. Further, the results of attribution-dissections in E1 indicated that 2 factors (rewarding and informational) contributed to the palatability. Finally, our results indicated that the palatability of sake was influenced by the dish eaten just before drinking.

  14. Large-area, high-intensity PV arrays for systems using dish concentrating optics

    Ward, J.S.; Duda, A.; Zweibel, K.; Coutts, T.J. [National Renewable Energy Lab., Golden, CO (United States)

    1998-09-01

    In this paper, the authors report on efforts to fabricate monolithic interconnected modules (MIMs) using III-V semiconductors with bandgaps appropriate for the terrestrial solar spectrum. The small size of the component cells comprising the MIM allows for operation at extremely high flux densities and relaxes the requirement for a small spot size to be generated by the optics. This makes possible a PV option for the large dish concentrator systems that have been developed by the solar thermal community for use with Stirling engines. Additionally, the highly effective back-surface reflector integrated into the MIM design is an effective tool for thermal management of the array. Development of this technology would radically alter the projections for PV manufacturing capacity because of the potential for extremely high power generation per unit area of semiconductor material.

  15. Comparative analyses for selected clean coal technologies in the international marketplace

    Szpunar, C.B.; Gillette, J.L.

    1990-07-01

    Clean coal technologies (CCTs) are being demonstrated in research and development programs under public and private sponsorship. Many of these technologies could be marketed internationally. To explore the scope of these international opportunities and to match particular technologies with markets appearing to have high potential, a study was undertaken that focused on seven representative countries: Italy, Japan, Morocco, Turkey, Pakistan, the Peoples' Republic of China, and Poland. The results suggest that there are international markets for CCTs and that these technologies can be cost competitive with more conventional alternatives. The identified markets include construction of new plants and refurbishment of existing ones, especially when decision makers want to decrease dependence on imported oil. This report describes potential international market niches for U.S. CCTs and discusses the status and implications of ongoing CCT demonstration activities. Twelve technologies were selected as representative of technologies under development for use in new or refurbished industrial or electric utility applications. Included are the following: Two generic precombustion technologies: two-stage froth-flotation coal beneficiation and coal-water mixtures (CWMs); Four combustion technologies: slagging combustors, integrated-gasification combined-cycle (IGCC) systems, atmospheric fluidized-bed combustors (AFBCs), and pressurized fluidized-bed combustors (PFBCs); and Six postcombustion technologies: limestone-injection multistage burner (LIMB) systems, gas-reburning sorbent-injection (GRSI) systems, dual-alkali flue-gas desulfurization (FGD), spray-dryer FGD, the NOXSO process, and selective catalytic reduction (SCR) systems. Major chapters of this report have been processed separately for inclusion on the data base.

  16. Regional food dishes in the Brazilian National School Food Program: Acceptability and nutritional composition

    Diogo thimoteo da Cunha

    2014-08-01

    Full Text Available Objective: the objective of this study was to evaluate the nutritional composition and describe the acceptability of regional culinary dishes served to students from public schools of rural and urban areas. Methods: Ten Brazilian regional dishes were evaluated for acceptability and nutritional composition. the survey was conducted in schools located in rural and urban areas of two cities in the state of São Paulo. Dish acceptability was evaluated using leftover analysis and a 5-point facial hedonic scale. the adherence index was calculated and used as an indirect measure of acceptance, and the nutritional composition was calculated based on the technical files of each dish. Results: A total of 2,384 students from 20 schools participated in the study and 1,174 tasted and evaluated the dishes. the test using the 5-point facial hedonic scale demonstrated that five dishes (Caldo verde soup, persimmon jelly, chicken with okra, puréed cornmeal with spinach, and arugula pizza had an acceptability rate above 85.0%. the mean adherence indices were 57.3% and 55.6% in urban and rural environments, respectively. Analysis of the nutritional composition of regional dishes indicates that these dishes can partially meet macronutrient recommendations. Conclusion: the tested dishes can become part of school menus as they were accepted or partly accepted by the students regardless of school location, whether rural or urban. the cultural heritage is an important resource for the food sovereignty of a country and should be constantly encouraged.

  17. Recent developments: PKI square dish for the Soleras Project

    Rogers, W. E.

    1984-03-01

    The Square Dish solar collectors are subjected to rigorous design attention regarding corrosion at the site, and certification of the collector structure. The microprocessor controls and tracking mechanisms are improved in the areas of fail safe operations, durability, and low parasitic power requirements. Prototype testing demonstrates performance efficiency of approximately 72% at 730 F outlet temperature. Studies are conducted that include developing formal engineering design studies, developing formal engineering design drawing and fabrication details, establishing subcontracts for fabrication of major components, and developing a rigorous quality control system. The improved design is more cost effective to product and the extensive manuals developed for assembly and operation/maintenance result in faster field assembly and ease of operation.

  18. Thermal Model of a Dish Stirling Cavity-Receiver

    Rubén Gil

    2015-01-01

    Full Text Available This paper presents a thermal model for a dish Stirling cavity based on the finite differences method. This model is a theoretical tool to optimize the cavity in terms of thermal efficiency. One of the main outcomes of this work is the evaluation of radiative exchange using the radiosity method; for that purpose, the view factors of all surfaces involved have been accurately calculated. Moreover, this model enables the variation of the cavity and receiver dimensions and the materials to determine the optimal cavity design. The tool has been used to study the cavity optimization regarding geometry parameters and material properties. Receiver absorptivity has been identified as the most influential property of the materials. The optimal aperture height depends on the minimum focal space.

  19. Advancing food, nutrition, and health research in Europe by connecting and building research infrastructures in a DISH-RI: Results of the EuroDISH project

    Snoek, Harriëtte M.; Eijssen, Lars M.T.; Geurts, Marjolein

    2018-01-01

    more effectively. Approach In the EuroDISH project we mapped existing RIs in the food and health area in Europe, identified outstanding needs, and synthesised this into a conceptual design of a pan-European DISH-RI. The DISH model was used to describe and structure the research area: Determinants...... of food choice, Intake of foods and nutrients, Status and functional markers of nutritional health, and Health and disease risk. Key findings The need to develop RIs in the food and health domain clearly emerged from the EuroDISH project. It showed the necessity for a unique interdisciplinary and multi......Background Research infrastructures (RIs) are essential to advance research on the relationship between food, nutrition, and health. RIs will facilitate innovation and allow insights at the systems level which are required to design (public health) strategies that will address societal challenges...

  20. Fire and collapse, Faculty of Architecture building, Delft University of Technology: Data collection and preliminary analyses

    Meacham, B.; Park, H.; Engelhardt, M.; Kirk, A.; Kodur, V.; Straalen, IJ.J.; Maljaars, J.; Weeren, K. van; Feijter, R. de; Both, K.

    2010-01-01

    On the morning of May 13, 2008, a fire that started in a coffee vending machine on the 6th floor of the 13-story Faculty of Architecture Building at the Delft University of Technology (TUD), Delft, the Netherlands, quickly developed into an extreme loading event. Although all building occupants

  1. Interactive Whiteboards and All That Jazz: Analysing Classroom Activity with Interactive Technologies

    Tanner, Howard; Beauchamp, Gary; Jones, Sonia; Kennewell, Steve

    2010-01-01

    The term "orchestration", has been used to describe the teacher's role in activity settings incorporating interactive technologies. This musical analogy suggests pre-planned manipulation of events to generate "performance" leading to learning. However, in two recent projects we have observed how effective teaching and learning…

  2. Analysing Production Technology and Risk in Organic and Conventional Dutch Arable Farming using Panel Data

    Gardebroek, C.; Chavez Clemente, M.D.; Oude Lansink, A.G.J.M.

    2010-01-01

    Abstract This paper compares the production technology and production risk of organic and conventional arable farms in the Netherlands. Just–Pope production functions that explicitly account for output variability are estimated using panel data of Dutch organic and conventional farms. Prior

  3. System Analyses of Pneumatic Technology for High Speed Civil Transport Aircraft

    Mavris, Dimitri N.; Tai, Jimmy C.; Kirby, Michelle M.; Roth, Bryce A.

    1999-01-01

    The primary aspiration of this study was to objectively assess the feasibility of the application of a low speed pneumatic technology, in particular Circulation Control (CC) to an HSCT concept. Circulation Control has been chosen as an enabling technology to be applied on a generic High Speed Civil Transport (HSCT). This technology has been proven for various subsonic vehicles including flight tests on a Navy A-6 and computational application on a Boeing 737. Yet, CC has not been widely accepted for general commercial fixed-wing use but its potential has been extensively investigated for decades in wind tunnels across the globe for application to rotorcraft. More recently, an experimental investigation was performed at Georgia Tech Research Institute (GTRI) with application to an HSCT-type configuration. The data from those experiments was to be applied to a full-scale vehicle to assess the impact from a system level point of view. Hence, this study attempted to quantitatively assess the impact of this technology to an HSCT. The study objective was achieved in three primary steps: 1) Defining the need for CC technology; 2) Wind tunnel data reduction; 3) Detailed takeoff/landing performance assessment. Defining the need for the CC technology application to an HSCT encompassed a preliminary system level analysis. This was accomplished through the utilization of recent developments in modern aircraft design theory at Aerospace Systems Design Laboratory (ASDL). These developments include the creation of techniques and methods needed for the identification of technical feasibility show stoppers. These techniques and methods allow the designer to rapidly assess a design space and disciplinary metric enhancements to enlarge or improve the design space. The takeoff and landing field lengths were identified as the concept "show-stoppers". Once the need for CC was established, the actual application of data and trends was assessed. This assessment entailed a reduction of the

  4. Healthier side dishes at restaurants: an analysis of children's perspectives, menu content, and energy impacts.

    Anzman-Frasca, Stephanie; Dawes, Franciel; Sliwa, Sarah; Dolan, Peter R; Nelson, Miriam E; Washburn, Kyle; Economos, Christina D

    2014-07-04

    Children consume restaurant-prepared foods at high rates, suggesting that interventions and policies targeting consumption of these foods have the potential to improve diet quality and attenuate excess energy intake. One approach to encouraging healthier dietary intake in restaurants is to offer fruits and vegetables (FV) as side dishes, as opposed to traditional, energy-dense accompaniments like French fries. The aims of the current study were to examine: children's views about healthier side dishes at restaurants; current side dish offerings on children's menus at leading restaurants; and potential energy reductions when substituting FV side dishes in place of French fries. To investigate children's attitudes, a survey was administered to a nationally representative sample of U.S. 8- to 18-year-olds (n = 1178). To examine current side dish offerings, children's menus from leading quick service (QSR; n = 10) and full service restaurant chains (FSR; n = 10) were analyzed. Energy reductions that could result from substituting commonly-offered FV side dishes for French fries were estimated using nutrition information corresponding to the children's menu items. Two-thirds of children reported that they would not feel negatively about receiving FV sides instead of French fries with kids' meals. Liking/taste was the most common reason that children gave to explain their attitudes about FV side dishes. Nearly all restaurants offered at least 1 FV side dish option, but at most restaurants (60% of QSR; 70% of FSR), FV sides were never served by default. Substituting FV side dishes for French fries yielded an average estimated energy reduction of at least 170 calories. Results highlight some healthy trends in the restaurant context, including the majority of children reporting non-negative attitudes about FV side dishes and the consistent availability of FV side dish options at leading QSR and FSR. Yet the minority of restaurants offer these FV sides by default

  5. Probabilistic Latent Semantic Analyses (PLSA in Bibliometric Analysis for Technology Forecasting

    Wang Zan

    2007-03-01

    Full Text Available Due to the availability of internet-based abstract services and patent databases, bibliometric analysis has become one of key technology forecasting approaches. Recently, latent semantic analysis (LSA has been applied to improve the accuracy in document clustering. In this paper, a new LSA method, probabilistic latent semantic analysis (PLSA which uses probabilistic methods and algebra to search latent space in the corpus is further applied in document clustering. The results show that PLSA is more accurate than LSA and the improved iteration method proposed by authors can simplify the computing process and improve the computing efficiency

  6. The Type and Impact of Evidence Review Group Exploratory Analyses in the NICE Single Technology Appraisal Process.

    Carroll, Christopher; Kaltenthaler, Eva; Hill-McManus, Daniel; Scope, Alison; Holmes, Michael; Rice, Stephen; Rose, Micah; Tappenden, Paul; Woolacott, Nerys

    2017-06-01

    As part of the UK National Institute for Health and Care Excellence (NICE) single technology appraisal process, independent evidence review groups (ERGs) critically appraise a company's submission relating to a specific technology and indication. To explore the type of additional exploratory analyses conducted by ERGs and their impact on the recommendations made by NICE. The 100 most recently completed single technology appraisals with published guidance were selected for inclusion. A content analysis of relevant documents was undertaken to identify and extract relevant data, and narrative synthesis was used to rationalize and present these data. The types of exploratory analysis conducted in relation to companies' models were fixing errors, addressing violations, addressing matters of judgment, and the provision of a new, ERG-preferred base case. Ninety-three of the 100 ERG reports contained at least one of these analyses. The most frequently reported type of analysis in these 93 ERG reports related to the category "Matters of judgment," which was reported in 83 reports (89%). At least one of the exploratory analyses conducted and reported by an ERG is mentioned in 97% of NICE appraisal consultation documents and 94% of NICE final appraisal determinations, and had a clear influence on recommendations in 72% of appraisal consultation documents and 47% of final appraisal determinations. These results suggest that the additional analyses undertaken by ERGs in the appraisal of company submissions are highly influential in the policy-making and decision-making process. Copyright © 2017 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  7. Accounting for Technological Change in Regulatory Impact Analyses: The Learning Curve Technique

    Taylor, Margaret [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fujita, K. Sydny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2013-04-30

    Regulatory impact assessment is formally required by the U.S. and many other nations in order to help governments weigh the costs and benefits of proposed regulations, particularly as they compare to those of alternative actions and other government priorities. 1 One of the “best practices” of regulatory impact assessments, as established by the OECD, is to use estimates of costs that are grounded in economic theory. Economic theory indicates that changes in compliance costs should be expected over time as a result of factors related to technological innovation. But many U.S. regulatory impact assessments have traditionally employed a practice that is in conflict with this expectation: they take current estimates of the costs of complying with a proposed regulation and project that those costs will remain unchanged over the full time period that the regulation would be in effect.

  8. Structural Performance’s Optimally Analysing and Implementing Based on ANSYS Technology

    Han, Na; Wang, Xuquan; Yue, Haifang; Sun, Jiandong; Wu, Yongchun

    2017-06-01

    Computer-aided Engineering (CAE) is a hotspot both in academic field and in modern engineering practice. Analysis System(ANSYS) simulation software for its excellent performance become outstanding one in CAE family, it is committed to the innovation of engineering simulation to help users to shorten the design process, improve product innovation and performance. Aimed to explore a structural performance’s optimally analyzing model for engineering enterprises, this paper introduced CAE and its development, analyzed the necessity for structural optimal analysis as well as the framework of structural optimal analysis on ANSYS Technology, used ANSYS to implement a reinforced concrete slab structural performance’s optimal analysis, which was display the chart of displacement vector and the chart of stress intensity. Finally, this paper compared ANSYS software simulation results with the measured results,expounded that ANSYS is indispensable engineering calculation tools.

  9. Prompt nuclear analytical techniques for material research in accelerator driven transmutation technologies: Prospects and quantitative analyses

    Vacik, J.; Hnatowicz, V.; Cervena, J.; Perina, V.; Mach, R.

    1998-01-01

    Accelerator driven transmutation technology (ADTT) is a promising way toward liquidation of spent nuclear fuel, nuclear wastes and weapon grade Pu. The ADTT facility comprises a high current (proton) accelerator supplying a sub-critical reactor assembly with spallation neutrons. The reactor part is supposed to be cooled by molten fluorides or metals which serve, at the same time, as a carrier of nuclear fuel. Assumed high working temperature (400-600 C) and high radiation load in the subcritical reactor and spallation neutron source put forward the problem of optimal choice of ADTT construction materials, especially from the point of their radiation and corrosion resistance when in contact with liquid working media. The use of prompt nuclear analytical techniques in ADTT related material research is considered and examples of preliminary analytical results obtained using neutron depth profiling method are shown for illustration. (orig.)

  10. Benefit Analyses of Technologies for Automatic Identification to Be Implemented in the Healthcare Sector

    Krey, Mike; Schlatter, Ueli

    The tasks and objectives of automatic identification (Auto-ID) are to provide information on goods and products. It has already been established for years in the areas of logistics and trading and can no longer be ignored by the German healthcare sector. Some German hospitals have already discovered the capabilities of Auto-ID. Improvements in quality, safety and reductions in risk, cost and time are aspects and areas where improvements are achievable. Privacy protection, legal restraints, and the personal rights of patients and staff members are just a few aspects which make the heath care sector a sensible field for the implementation of Auto-ID. Auto-ID in this context contains the different technologies, methods and products for the registration, provision and storage of relevant data. With the help of a quantifiable and science-based evaluation, an answer is sought as to which Auto-ID has the highest capability to be implemented in healthcare business.

  11. Dish-based CPV-T for rooftop generation

    Davila-Peralta, Christian; Hyatt, Justin; Alfred, Dan; Struble, Morgan; Sodari, Frank; Angel, Roger

    2017-09-01

    Hybrid CPV-T with combined electrical and thermal output is well suited to solar generation from fixed limited areas, such as on the roof of an industrial or commercial facility with need for heat. This application will become especially attractive once overall electrical conversion efficiency of 40% is reached, as is projected for REhnu CPV systems using multijunction cells of 50% efficiency, anticipated in a few years. We outline here a configuration of dish- based CPV trackers optimized for close packing on a flat roof in a triangular grid, with a mirror area-to-ground area ratio of 50%. When the geometry of shadowing averaged over a year is taken into account, 80% of all the sunlight that would strike the rooftop is directed into the receivers. Such an array on a given area of flat roof will generate more electrical energy than would be possible with conventional PV panels, even if covering the entire rooftop, because of silicon's relative inefficiency. For example, in Tucson, the annual average global flux of 5.7 kWh/m2/day on a horizontal surface covered with 22% silicon modules will yield 1.25 kWh/m2/day. We show that a CPV system collecting 80% of all the direct sunlight of 7.0 kWh/m2 and converting it with 40% efficiency will yield 2.24 kWh/m2/day of rooftop area, nearly twice as much4. Thermal power will double again the total energy yield. A dual axis CPV-T tracker designed specifically very close spacing has been built to carry a single dish mirror of the standard type used in REhnu's M-8 generator, described by Stalcup et al in these proceedings1,2. Sunlight is collected and focused by a single square paraboloidal mirror, 1.65 × 1.65 m with focal length of 1.5 m. For closest possible packing without mechanical interference, and for broad distribution of load on a rooftop, the mirror and receiver are mounted to a C-ring structure, configured such that the elevation and azimuth axes intersect at a virtual pivot, at the center of the sphere that just

  12. Radiation Exposure Analyses Supporting the Development of Solar Particle Event Shielding Technologies

    Walker, Steven A.; Clowdsley, Martha S.; Abston, H. Lee; Simon, Hatthew A.; Gallegos, Adam M.

    2013-01-01

    NASA has plans for long duration missions beyond low Earth orbit (LEO). Outside of LEO, large solar particle events (SPEs), which occur sporadically, can deliver a very large dose in a short amount of time. The relatively low proton energies make SPE shielding practical, and the possibility of the occurrence of a large event drives the need for SPE shielding for all deep space missions. The Advanced Exploration Systems (AES) RadWorks Storm Shelter Team was charged with developing minimal mass SPE storm shelter concepts for missions beyond LEO. The concepts developed included "wearable" shields, shelters that could be deployed at the onset of an event, and augmentations to the crew quarters. The radiation transport codes, human body models, and vehicle geometry tools contained in the On-Line Tool for the Assessment of Radiation In Space (OLTARIS) were used to evaluate the protection provided by each concept within a realistic space habitat and provide the concept designers with shield thickness requirements. Several different SPE models were utilized to examine the dependence of the shield requirements on the event spectrum. This paper describes the radiation analysis methods and the results of these analyses for several of the shielding concepts.

  13. Additional Development and Systems Analyses of Pneumatic Technology for High Speed Civil Transport Aircraft

    Englar, Robert J.; Willie, F. Scott; Lee, Warren J.

    1999-01-01

    In the Task I portion of this NASA research grant, configuration development and experimental investigations have been conducted on a series of pneumatic high-lift and control surface devices applied to a generic High Speed Civil Transport (HSCT) model configuration to determine their potential for improved aerodynamic performance, plus stability and control of higher performance aircraft. These investigations were intended to optimize pneumatic lift and drag performance; provide adequate control and longitudinal stability; reduce separation flowfields at high angle of attack; increase takeoff/climbout lift-to-drag ratios; and reduce system complexity and weight. Experimental aerodynamic evaluations were performed on a semi-span HSCT generic model with improved fuselage fineness ratio and with interchangeable plain flaps, blown flaps, pneumatic Circulation Control Wing (CCW) high-lift configurations, plain and blown canards, a novel Circulation Control (CC) cylinder blown canard, and a clean cruise wing for reference. Conventional tail power was also investigated for longitudinal trim capability. Also evaluated was unsteady pulsed blowing of the wing high-lift system to determine if reduced pulsed mass flow rates and blowing requirements could be made to yield the same lift as that resulting from steady-state blowing. Depending on the pulsing frequency applied, reduced mass flow rates were indeed found able to provide lift augmentation at lesser blowing values than for the steady conditions. Significant improvements in the aerodynamic characteristics leading to improved performance and stability/control were identified, and the various components were compared to evaluate the pneumatic potential of each. Aerodynamic results were provided to the Georgia Tech Aerospace System Design Lab. to conduct the companion system analyses and feasibility study (Task 2) of theses concepts applied to an operational advanced HSCT aircraft. Results and conclusions from these

  14. [Research on fast classification based on LIBS technology and principle component analyses].

    Yu, Qi; Ma, Xiao-Hong; Wang, Rui; Zhao, Hua-Feng

    2014-11-01

    Laser-induced breakdown spectroscopy (LIBS) and the principle component analysis (PCA) were combined to study aluminum alloy classification in the present article. Classification experiments were done on thirteen different kinds of standard samples of aluminum alloy which belong to 4 different types, and the results suggested that the LIBS-PCA method can be used to aluminum alloy fast classification. PCA was used to analyze the spectrum data from LIBS experiments, three principle components were figured out that contribute the most, the principle component scores of the spectrums were calculated, and the scores of the spectrums data in three-dimensional coordinates were plotted. It was found that the spectrum sample points show clear convergence phenomenon according to the type of aluminum alloy they belong to. This result ensured the three principle components and the preliminary aluminum alloy type zoning. In order to verify its accuracy, 20 different aluminum alloy samples were used to do the same experiments to verify the aluminum alloy type zoning. The experimental result showed that the spectrum sample points all located in their corresponding area of the aluminum alloy type, and this proved the correctness of the earlier aluminum alloy standard sample type zoning method. Based on this, the identification of unknown type of aluminum alloy can be done. All the experimental results showed that the accuracy of principle component analyses method based on laser-induced breakdown spectroscopy is more than 97.14%, and it can classify the different type effectively. Compared to commonly used chemical methods, laser-induced breakdown spectroscopy can do the detection of the sample in situ and fast with little sample preparation, therefore, using the method of the combination of LIBS and PCA in the areas such as quality testing and on-line industrial controlling can save a lot of time and cost, and improve the efficiency of detection greatly.

  15. Valley of Death analysis for polymer PV technology; Valley of Death analyse voor polymere PV technologie

    Schoots, K. [ECN Beleidsstudies, Petten (Netherlands)

    2013-12-15

    This report describes the results of a qualitative study of the barriers that actors involved in the development and commercialization of polymer solar cells, may encounter. The purpose of this socio-economic research is to identify these barriers for the (market) development of thin film polymeric PV technology and to develop strategies for them in order to overcome the constraints. The necessary data are collected from interviews with actors who are active in the development and deployment of conventional solar cells. Based on the results from this study, it is conclude that it is important for the Organic PV industry to carry out many market experiments beyond the built environment. The report provides recommendations with regard to the markets in which these experiments are most likely to succeed and which drivers should be taken into account [Dutch] Dit rapport beschrijft de resultaten van een kwalitatief onderzoek naar de barrieres die actoren, betrokken bij de ontwikkeling en marktintroductie van polymere zonnecellen, kunnen tegenkomen. Het doel van dit sociaal-economische onderzoek is deze barrieres voor de (markt)ontwikkeling van dunne film polymere PV technologie te identificeren en strategieen te ontwikkelen om ze voor te zijn of ze te overbruggen. De benodigde gegevens worden verzameld uit interviews met actoren die actief zijn in de ontwikkeling en uitrol van conventionele zonnecellen. Op basis van de resultaten uit dit onderzoek komen we tot de conclusie dat het voor de Organische PV sector belangrijk is veel marktexperimenten aan te gaan buiten de gebouwde omgeving. Het rapport geeft aanbevelingen in welke soort markten deze experimenten de meeste kans van slagen hebben en met welke drivers van marktpartijen rekening moet worden gehouden.

  16. Issues Related to the Frequency of Exploratory Analyses by Evidence Review Groups in the NICE Single Technology Appraisal Process.

    Kaltenthaler, Eva; Carroll, Christopher; Hill-McManus, Daniel; Scope, Alison; Holmes, Michael; Rice, Stephen; Rose, Micah; Tappenden, Paul; Woolacott, Nerys

    2017-06-01

    Evidence Review Groups (ERGs) critically appraise company submissions as part of the National Institute for Health and Care Excellence (NICE) Single Technology Appraisal (STA) process. As part of their critique of the evidence submitted by companies, the ERGs undertake exploratory analyses to explore uncertainties in the company's model. The aim of this study was to explore pre-defined factors that might influence or predict the extent of ERG exploratory analyses. The aim of this study was to explore predefined factors that might influence or predict the extent of ERG exploratory analyses. We undertook content analysis of over 400 documents, including ERG reports and related documentation for the 100 most recent STAs (2009-2014) for which guidance has been published. Relevant data were extracted from the documents and narrative synthesis was used to summarise the extracted data. All data were extracted and checked by two researchers. Forty different companies submitted documents as part of the NICE STA process. The most common disease area covered by the STAs was cancer (44%), and most ERG reports (n = 93) contained at least one exploratory analysis. The incidence and frequency of ERG exploratory analyses does not appear to be related to any developments in the appraisal process, the disease area covered by the STA, or the company's base-case incremental cost-effectiveness ratio (ICER). However, there does appear to be a pattern in the mean number of analyses conducted by particular ERGs, but the reasons for this are unclear and potentially complex. No clear patterns were identified regarding the presence or frequency of exploratory analyses, apart from the mean number conducted by individual ERGs. More research is needed to understand this relationship.

  17. ArrayWiki: an enabling technology for sharing public microarray data repositories and meta-analyses

    Stokes, Todd H; Torrance, JT; Li, Henry; Wang, May D

    2008-01-01

    (Semantic Agents) such as Google to further enhance data discovery. Conclusions Microarray data and meta information in ArrayWiki are distributed and visualized using a novel and compact data storage format, BioPNG. Also, they are open to the research community for curation, modification, and contribution. By making a small investment of time to learn the syntax and structure common to all sites running MediaWiki software, domain scientists and practioners can all contribute to make better use of microarray technologies in research and medical practices. ArrayWiki is available at . PMID:18541053

  18. [Sodium, potassium and calcium content in regional dishes consumed in Sonora, Mexico].

    Grijalva Haro, M I; Valencia, M E; Wyatt, J

    1990-06-01

    The content of sodium, potassium and calcium was determined in 15 regional dishes, by atomic absorption spectrophotometry. The Na:K ratio was high in most of the dishes due to the high sodium content and low content of potassium found. The higher sources of the studied minerals were "tortilla de harina" with 1,372.8 mg/100 g of sodium; "chorizo con papas" with 466 mg/100 g of potassium, and "calabacitas con queso" with 244.1 mg/100 g of calcium. Two of the dishes considered as desserts, "capirotada" and "arroz con leche" showed the lowest Na:K ratio (0.66 and 0.81, respectively).

  19. Test results on parabolic dish concentrators for solar thermal power systems

    Jaffe, Leonard D.

    1989-01-01

    This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

  20. Differences in nutrient composition and choice of side dishes between red meat and fish dinners in Norwegian adults

    Jannicke Borch Myhre

    2016-01-01

    Full Text Available Background: Food-based dietary guidelines often recommend increased consumption of fish and reduced intake of red and processed meat. However, little is known about how changing the main protein source from red meat to fish may influence the choice of side dishes. Objective: To investigate whether side dish choices differed between red meat and fish dinners. Moreover, to compare intakes of macronutrients and selected micronutrients in red meat and fish dinners and to see whether whole-day intakes of these nutrients differed between days with red meat dinners and days with fish dinners. Design: Data were collected in a cross-sectional nationwide Norwegian dietary survey using two non-consecutive telephone-administered 24-h recalls. The recalls were conducted approximately 4 weeks apart. In total, 2,277 dinners from 1,517 participants aged 18–70 were included in the analyses. Results: Fish dinners were more likely to include potatoes and carrots than red meat dinners, whereas red meat dinners more often contained bread, tomato sauce, and cheese. Red meat dinners contained more energy and iron; had higher percentages of energy (E% from fat, saturated fat, and monounsaturated fat; and a lower E% from protein and polyunsaturated fat than fish dinners. Fish dinners contained more vitamin D, β-carotene, and folate than red meat dinners. Similar differences were found when comparing whole-day intakes of the same nutrients on days with red meat versus fish dinners. Conclusion: Fish dinners were accompanied by different side dishes than red meat dinners. With regard to nutrient content, fish dinners generally had a healthier profile than red meat dinners. However, iron intake was higher for red meat dinners. Information about associated foods will be useful both for developing public health guidelines and when studying associations between dietary factors and health outcomes.

  1. A review of test results on parabolic dish solar thermal power modules with dish-mounted Rankine engines and for production of process steam

    Jaffe, Leonard D.

    1988-11-01

    This paper presents results of development testing of various solar thermal parabolic dish modules and assemblies. Most of the tests were at modules and assemblies that used a dish-mounted, organic Rankine cycle turbine for production of electric power. Some tests were also run on equipment for production of process steam or for production of electricity using dish-mounted reciprocating steam engines. These tests indicate that early modules achieve efficiencies of about 18 percent in converting sunlight to electricity (excluding the inverter but including parasitics). A number of malfunctions occurred. The performance measurements, as well as the malfunctions and other operating experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  2. Computer analyses for the design, operation and safety of new isotope production reactors: A technology status review

    Wulff, W.

    1990-01-01

    A review is presented on the currently available technologies for nuclear reactor analyses by computer. The important distinction is made between traditional computer calculation and advanced computer simulation. Simulation needs are defined to support the design, operation, maintenance and safety of isotope production reactors. Existing methods of computer analyses are categorized in accordance with the type of computer involved in their execution: micro, mini, mainframe and supercomputers. Both general and special-purpose computers are discussed. Major computer codes are described, with regard for their use in analyzing isotope production reactors. It has been determined in this review that conventional systems codes (TRAC, RELAP5, RETRAN, etc.) cannot meet four essential conditions for viable reactor simulation: simulation fidelity, on-line interactive operation with convenient graphics, high simulation speed, and at low cost. These conditions can be met by special-purpose computers (such as the AD100 of ADI), which are specifically designed for high-speed simulation of complex systems. The greatest shortcoming of existing systems codes (TRAC, RELAP5) is their mismatch between very high computational efforts and low simulation fidelity. The drift flux formulation (HIPA) is the viable alternative to the complicated two-fluid model. No existing computer code has the capability of accommodating all important processes in the core geometry of isotope production reactors. Experiments are needed (heat transfer measurements) to provide necessary correlations. It is important for the nuclear community, both in government, industry and universities, to begin to take advantage of modern simulation technologies and equipment. 41 refs

  3. Transparency in practice: Evidence from 'verification analyses' issued by the Polish Agency for Health Technology Assessment in 2012-2015.

    Ozierański, Piotr; Löblová, Olga; Nicholls, Natalia; Csanádi, Marcell; Kaló, Zoltán; McKee, Martin; King, Lawrence

    2018-01-08

    Transparency is recognised to be a key underpinning of the work of health technology assessment (HTA) agencies, yet it has only recently become a subject of systematic inquiry. We contribute to this research field by considering the Polish Agency for Health Technology Assessment (AHTAPol). We situate the AHTAPol in a broader context by comparing it with the National Institute for Health and Care Excellence (NICE) in England. To this end, we analyse all 332 assessment reports, called verification analyses, that the AHTAPol issued from 2012 to 2015, and a stratified sample of 22 Evidence Review Group reports published by NICE in the same period. Overall, by increasingly presenting its key conclusions in assessment reports, the AHTAPol has reached the transparency standards set out by NICE in transparency of HTA outputs. The AHTAPol is more transparent than NICE in certain aspects of the HTA process, such as providing rationales for redacting assessment reports and providing summaries of expert opinions. Nevertheless, it is less transparent in other areas of the HTA process, such as including information on expert conflicts of interest. Our findings have important implications for understanding HTA in Poland and more broadly. We use them to formulate recommendations for policymakers.

  4. Nutritional composition of the commonly consumed composite dishes for the Barbados National Cancer Study.

    Sharma, Sangita; Harris, Rachel; Cao, Xia; Hennis, Anselm J M; Leske, M Cristina; Wu, Suh-Yuh

    2007-09-01

    To provide, for the first time, the calculated nutritional composition of 32 composite dishes commonly consumed in Barbados to enable dietary intake to be calculated from a Quantitative Food Frequency Questionnaire developed specifically for this population to determine associations between diet and risk of prostate and breast cancer. Weighed recipes were collected in up to six different households for each of the 32 composite dishes. The average nutritional composition for these composite dishes was calculated using the US Department of Agriculture National Nutrient Database. One hundred and fifty-two weighed recipes were collected for 32 composite dishes: five were fish based, two were ground beef dishes, two were chicken based, two were offal based, two were lamb dishes, one was pork based, three were rice based, three were commonly consumed home-made drinks, and the remaining were miscellaneous items. A total of 152 weighed recipes were collected and we provide, for the first time, nutritional composition data for 32 commonly consumed food and drink items in Barbados. Such data are essential for assessing nutrient intake and determining associations between diet and prostate and breast cancer in the Barbados National Cancer Study.

  5. Efficient, Low Cost Dish Concentrator for a CPV Based Cogeneration System

    Chayet, Haim; Kost, Ori; Moran, Rani; Lozovsky, Ilan

    2011-12-01

    Zenith Solar Ltd has developed efficient electricity and heat co-generation system based on segmented-parabolic dish of total aperture area of 11 m2 and water cooled dense array module combined of triple junction cells. Conventional parabolic dishes are inherently inefficient in the sense that the radiant flux distribution is non uniform causing inefficient generation by the PV array. Secondary optics improves uniformity but introduces additional complexity and losses to the system. Zenith's dish is assembled of 1200 flat mirrors of approximately 100 cm2 each. Every mirror facet has a unique shape such that the geometrical projection from each mirror on the focal plane is essentially the same. When perfectly aligned, the projected radiation from all mirrors overlaps uniformly on the PV surface. The low cost construction of the dish utilizes plastic mount supported by a precise metal frame. The precision of the metal frame affects the overall optical efficiency of the mirror and hence the efficiency of the system. State of the art dish of 11 m2 active aperture results in output of 2.25 kWp (900 W/m2) electrical and 5 kWp thermal power from one dish system representing 21% electrical and 50% thermal conversion efficiency adding to 71% overall system efficiency.

  6. Analysis of ewe’s milk by FT Near Infrared spectroscopy: measurement of samples on Petri dishes in reflectance mode

    Květoslava Šustová

    2006-01-01

    Full Text Available Our work deals with a possibility of determination of basic composition (dry matter, fat, protein, casein, lactose and urea nitrogen of ewe’s milk and colostrum by FT NIR spectroscopy. Samples of milk were warmed to 40 °C, agitated, cooled to 20 °C, transferred into Petri dishes and analysed by reference methods and by FT NIR in reflectance mode. The measured area was spaced by a metallic mirror. Statistically significant differences between the reference values and the calculated values of NIR were not found (p=0.05. Results of calibration for ewe’s milk determined the highest correlation coefficients: dry matter 0.983, fat 0.989, true protein 0.997, casein 0.977, lactose 0.980 and urea nitrogen 0.973. The study showed that NIRS method, when samples of milk are measured on Petri dishes, is a useful technique for the prediction of dry matter, fat, protein and casein in ewe’s milk.

  7. The influence of the technologically advanced evacuation models on the risk analyses during accidents in LNG terminal

    Stankovicj, Goran; Petelin, Stojan [Faculty for Maritime Studies and Transport, University of Ljubljana, Portorozh (Sierra Leone); others, and

    2014-07-01

    The evacuation of people located in different safety zones of an LNG terminal is a complex problem considering that the accidents involving LNG are very hazardous and post the biggest threat to the safety of the people located near the LNG leakage. The safety risk criteria define the parameters which one LNG terminal should meet in terms of safety. Those criteria also contain an evacuation as an evasive action with the objective to mitigate the influence of the LNG accident on the people at risk. Till date, not a lot of attention has been paid to technologically advanced evacuations intended for LNG terminals. Creating the technologically advanced evacuation influences directly on the decrease of the probability of fatalities P{sub f,i}, thus influencing the calculation of the individual risk as well as the societal risk which results in the positioning of the F-N curve in the acceptable part of the ALARP zone. With this paper, we aim to present the difference between the safety analyses in cases when conservative data for P{sub f,i} is being used while calculating the risk, and in cases when real data for P{sub f,i} is been used. (Author)

  8. Automated water analyser computer supported system (AWACSS) Part I: Project objectives, basic technology, immunoassay development, software design and networking.

    Tschmelak, Jens; Proll, Guenther; Riedt, Johannes; Kaiser, Joachim; Kraemmer, Peter; Bárzaga, Luis; Wilkinson, James S; Hua, Ping; Hole, J Patrick; Nudd, Richard; Jackson, Michael; Abuknesha, Ram; Barceló, Damià; Rodriguez-Mozaz, Sara; de Alda, Maria J López; Sacher, Frank; Stien, Jan; Slobodník, Jaroslav; Oswald, Peter; Kozmenko, Helena; Korenková, Eva; Tóthová, Lívia; Krascsenits, Zoltan; Gauglitz, Guenter

    2005-02-15

    A novel analytical system AWACSS (automated water analyser computer-supported system) based on immunochemical technology has been developed that can measure several organic pollutants at low nanogram per litre level in a single few-minutes analysis without any prior sample pre-concentration nor pre-treatment steps. Having in mind actual needs of water-sector managers related to the implementation of the Drinking Water Directive (DWD) (98/83/EC, 1998) and Water Framework Directive WFD (2000/60/EC, 2000), drinking, ground, surface, and waste waters were major media used for the evaluation of the system performance. The instrument was equipped with remote control and surveillance facilities. The system's software allows for the internet-based networking between the measurement and control stations, global management, trend analysis, and early-warning applications. The experience of water laboratories has been utilised at the design of the instrument's hardware and software in order to make the system rugged and user-friendly. Several market surveys were conducted during the project to assess the applicability of the final system. A web-based AWACSS database was created for automated evaluation and storage of the obtained data in a format compatible with major databases of environmental organic pollutants in Europe. This first part article gives the reader an overview of the aims and scope of the AWACSS project as well as details about basic technology, immunoassays, software, and networking developed and utilised within the research project. The second part article reports on the system performance, first real sample measurements, and an international collaborative trial (inter-laboratory tests) to compare the biosensor with conventional anayltical methods.

  9. Metagenomic data of fungal internal transcribed spacer from serofluid dish, a traditional Chinese fermented food

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture for thousands of years, is made from vegetables by fermentation. In this work, microorganism community of the fermented serofluid dish was investigated by the culture-independent method. The metagenomic data in this article contains the sequences of fungal internal transcribed spacer (ITS regions of rRNA genes from 12 different serofluid dish samples. The metagenome comprised of 50,865 average raw reads with an average of 8,958,220 bp and G + C content is 45.62%. This is the first report on metagenomic data of fungal ITS from serofluid dish employing Illumina platform to profile the fungal communities of this little known fermented food from Gansu Province, China. The Metagenomic data of fungal internal transcribed spacer can be accessed at NCBI, SRA database accession no. SRP067411. Keywords: Serofluid dish, Jiangshui, Fungal ITS, Cultivation-independent, Microbial diversity

  10. Performance comparisons of dish type solar concentrator with mirror arrangements and receiver shapes

    Seo, Joo Hyun; Kim, Yong; Ma, Dae Sung; Seo, Tae Beom [Graduate School, Dept. of Mechanical Engineering, Inha Univ., Inchon (Korea, Republic of); Kang, Yong Heack [Korea Inst. of Energy Research, Daejeon (Korea, Republic of)

    2008-07-01

    The performance comparisons of dish type solar concentrators are numerically investigated. The dish type solar concentrator considered in this paper consists of a receiver and multi-faceted mirrors. In order to investigate the performance comparisons of dish type solar concentrators, six different mirror arrangements and four different receivers are considered. A parabolic-shaped perfect mirror of which diameter is 1.40 m is considered as the reference for the mirror arrangements. The other mirror arrangements consist of twelve identical parabolic-shaped mirror facets of which diameter are 0.405 m. Their total collecting areas, which are 1.545 m{sup 2}, are the same. Four different solar receiver shapes are a conical, a dome, a cylindrical, and a unicorn type. In order to investigate the thermal performance of the dish type solar concentrator, the radiative heat loss in the receiver should be calculated. For calculation, the net radiation method and the Monte-Carlo method are used. Also, because the thermal performance of the dish type solar concentrator can vary as the receiver surface temperature, the various surface temperatures are considered. Based on the calculation, the unicorn type has the best performance in receiver shapes and the STAR has the best performance in mirror arrangements except the perfect mirror. (orig.)

  11. Preliminary Accident Analyses for Conversion of the Massachusetts Institute of Technology Reactor (MITR) from Highly Enriched to Low Enriched Uranium

    Dunn, Floyd E. [Argonne National Lab. (ANL), Argonne, IL (United States); Olson, Arne P. [Argonne National Lab. (ANL), Argonne, IL (United States); Wilson, Erik H. [Argonne National Lab. (ANL), Argonne, IL (United States); Sun, Kaichao S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Newton, Jr., Thomas H. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hu, Lin-wen [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2013-09-30

    The Massachusetts Institute of Technology Reactor (MITR-II) is a research reactor in Cambridge, Massachusetts designed primarily for experiments using neutron beam and in-core irradiation facilities. It delivers a neutron flux comparable to current LWR power reactors in a compact 6 MW core using Highly Enriched Uranium (HEU) fuel. In the framework of its non-proliferation policies, the international community presently aims to minimize the amount of nuclear material available that could be used for nuclear weapons. In this geopolitical context most research and test reactors, both domestic and international, have started a program of conversion to the use of LEU fuel. A new type of LEU fuel based on an alloy of uranium and molybdenum (U-Mo) is expected to allow the conversion of U.S. domestic high performance reactors like MITR. This report presents the preliminary accident analyses for MITR cores fueled with LEU monolithic U-Mo alloy fuel with 10 wt% Mo. Preliminary results demonstrate adequate performance, including thermal margin to expected safety limits, for the LEU accident scenarios analyzed.

  12. Cultivation-independent comprehensive investigations on bacterial communities in serofluid dish, a traditional Chinese fermented food

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture, is made from vegetables by fermentation. In this study, bacterial community of the fermented serofluid dish was assessed by Illumina amplicon sequencing. The metagenome comprised of 49,589 average raw reads with an average 11,497,917 bp and G+C content is 52.46%. This is the first report on V4 hyper-variable region of the 16S rRNA metagenome sequence employing Illumina platform to profile the microbial community of this little known fermented food from Gansu Province, China. The metagenome sequence can be accessed at NCBI, SRA database accession no. SRP065370. Keywords: Serofluid dish, Jiangshui, 16S rRNA, Cultivation-independent, Microbial diversity

  13. Wind load design methods for ground-based heliostats and parabolic dish collectors

    Peterka, J A; Derickson, R G [Colorado State Univ., Fort Collins, CO (United States). Fluid Dynamics and Diffusion Lab.

    1992-09-01

    The purpose of this design method is to define wind loads on flat heliostat and parabolic dish collectors in a simplified form. Wind loads are defined for both mean and peak loads accounting for the protective influence of upwind collectors, wind protective fences, or other wind-blockage elements. The method used to define wind loads was to generalize wind load data obtained during tests on model collectors, heliostats or parabolic dishes, placed in a modeled atmospheric wind in a boundary-layer wind-tunnel at Colorado State University. For both heliostats and parabolic dishes, loads are reported for solitary collectors and for collectors as elements of a field. All collectors were solid with negligible porosity; thus the effects of porosity in the collectors is not addressed.

  14. Preparation of contemporary dishes and a functional drink using Japan's heirloom vegetable, Katsura-uri

    Azusa Sasaki

    2018-03-01

    Full Text Available Background: The fruit of Katsura-uri, traditionally used in the preparation of pickles in Japan, is facing an extinction crisis. In addition to the traditional dishes prepared from Katsura-uri, alternative dishes using the fruit should be devised to increase consumer demands for the protection of the heirloom vegetable. We attempted designing new Katsura-uri contemporary dishes and assessed the application of Katsura-uri juice as a functional drink without raising blood glucose levels. Methods: Cooking experiments were conducted with Katsura-uri in its ripening stages, based on the advice from a licensed chef and a registered dietitian in Japan. In the questionnaire-based sensory evaluation, consumer acceptability of Katsura-uri juice was assessed. The blood glucose levels were measured after healthy volunteers consumed the juice. Results: We demonstrated six new Katsura-uri dishes. In the questionnaire-based sensory evaluation of Katsura-uri juice, the assessment values for taste and fragrance were high. In human trials, the levels of incremental area under the curve and glucose spike were significantly lower after consumption of Katsura-uri juice, as compared to those after consumption of muskmelon juice. Conclusion: Katsura-uri-containing contemporary dishes and juice would help continue the consumption of the vegetable. Based on the results of the questionnaire, we also concluded that the use of Katsura-uri as a functional drink without raising blood glucose levels is superior to its use as contemporary dishes. These findings provide useful strategies to protect Katsura-uri from extinction. Keywords: Blood glucose, Diabetes, Functional food, Heirloom vegetable, Traditional customs

  15. The NOD3 software package: A graphical user interface-supported reduction package for single-dish radio continuum and polarisation observations

    Müller, Peter; Krause, Marita; Beck, Rainer; Schmidt, Philip

    2017-10-01

    Context. The venerable NOD2 data reduction software package for single-dish radio continuum observations, which was developed for use at the 100-m Effelsberg radio telescope, has been successfully applied over many decades. Modern computing facilities, however, call for a new design. Aims: We aim to develop an interactive software tool with a graphical user interface for the reduction of single-dish radio continuum maps. We make a special effort to reduce the distortions along the scanning direction (scanning effects) by combining maps scanned in orthogonal directions or dual- or multiple-horn observations that need to be processed in a restoration procedure. The package should also process polarisation data and offer the possibility to include special tasks written by the individual user. Methods: Based on the ideas of the NOD2 package we developed NOD3, which includes all necessary tasks from the raw maps to the final maps in total intensity and linear polarisation. Furthermore, plot routines and several methods for map analysis are available. The NOD3 package is written in Python, which allows the extension of the package via additional tasks. The required data format for the input maps is FITS. Results: The NOD3 package is a sophisticated tool to process and analyse maps from single-dish observations that are affected by scanning effects from clouds, receiver instabilities, or radio-frequency interference. The "basket-weaving" tool combines orthogonally scanned maps into a final map that is almost free of scanning effects. The new restoration tool for dual-beam observations reduces the noise by a factor of about two compared to the NOD2 version. Combining single-dish with interferometer data in the map plane ensures the full recovery of the total flux density. Conclusions: This software package is available under the open source license GPL for free use at other single-dish radio telescopes of the astronomical community. The NOD3 package is designed to be

  16. 78 FR 59633 - Wireless Telecommunications Bureau Opens Docket To Seek Comment on DISH Network Corporation's...

    2013-09-27

    ... 9, 2013, the DISH Network Corporation, on behalf of its wholly-owned subsidiaries, Gamma Acquisition... held by its wholly-owned subsidiaries, Gamma Acquisition LLC (Call Signs T060430001-T060430176) and New... Commission's Secretary must be delivered to FCC Headquarters at 445 12th Street SW., Room TW-A325, Washington...

  17. Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System

    2013-08-01

    Executive Orders FOB - Forward Operating Base FPSE - Free Piston Stirling Engine GHG - Greenhouse Gas ICC - International Code Council IMA... Stirling Engine (FPSE) for military, commercial, and space applications for almost 30 years. These developments have included multiple fuel types...product for its Free Piston Stirling Engine operating on solar energy for electricity production, called the PowerDishTM, a reasonable extension for

  18. A small scale cell culture system to analyze mechanobiology using reporter gene constructs and polyurethane dishes

    Seefried, Lothar; Mueller-Deubert, Sigrid; Wentzer, Thomas Schwarz

    2010-01-01

    of mechanotransduction and its crosstalk with biochemically induced signal transduction, AP1 and SP1 luciferase reporter gene constructs were cloned and transfected into various cell lines and primary cells. A newly developed bioreactor and small-scale 24-well polyurethane dishes were used to apply cyclic stretching...

  19. Nutritional Quality of School Meals in France: Impact of Guidelines and the Role of Protein Dishes

    Florent Vieux

    2018-02-01

    Full Text Available In France, school meals must comply with 15 frequency criteria (FC expressed as nutritional requirements (e.g., “starters containing more than 15% fat served no more than four times out of 20” in a series of 20 consecutive meals. The objective was to assess, for the first time, the nutritional impact of complying with French school food FC. Based on 40 series of meals actually served in primary schools (“observed series”, several scenarios (1600 series per scenario of compliance or non-compliance with FC were simulated, and nutritional quality was assessed via the mean adequacy ratio (MAR/2000 kcal. In the observed series, only 9.7 FC on average (range 4–14 were fulfilled. In the simulated series: (i MAR was positively associated with FC compliance level, with the highest MAR obtained with complete compliance; (ii MAR decreased when meat or fish-based dishes were replaced by dishes without meat or fish; and (iii removing the protein dish without replacement led to the lowest MAR. This study demonstrates that French school food guidelines ensure good nutritional quality of food services. It also shows that generalizing the service of meals without meat or fish would deteriorate overall nutritional quality, highlighting the need to define the composition of vegetarian dishes and their frequency of service to children.

  20. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

    Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron [MIT Kavli Institute, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bradley, Richard F. [Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA 22904 (United States); DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S. [Department of Astronomy, University of California, Berkeley, CA (United States); Aguirre, James E.; Kohn, Saul A. [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, PA (United States); Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C. [Arizona State University, School of Earth and Space Exploration, Tempe, AZ 85287 (United States); Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J. [National Radio Astronomy Observatory, Charlottesville, VA (United States); and others

    2016-08-01

    The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m{sup 2} in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

  1. Modelling dishes and exploring culinary 'precisions': the two issues of molecular gastronomy.

    This, Hervé

    2005-04-01

    The scientific strategy of molecular gastronomy includes modelling 'culinary definitions' and experimental explorations of 'culinary precisions'. A formalism that describes complex dispersed systems leads to a physical classification of classical sauces, as well as to the invention of an infinite number of new dishes.

  2. Nutritional Quality of School Meals in France: Impact of Guidelines and the Role of Protein Dishes.

    Vieux, Florent; Dubois, Christophe; Duchêne, Christelle; Darmon, Nicole

    2018-02-13

    In France, school meals must comply with 15 frequency criteria (FC) expressed as nutritional requirements (e.g., "starters containing more than 15% fat served no more than four times out of 20") in a series of 20 consecutive meals. The objective was to assess, for the first time, the nutritional impact of complying with French school food FC. Based on 40 series of meals actually served in primary schools ("observed series"), several scenarios (1600 series per scenario) of compliance or non-compliance with FC were simulated, and nutritional quality was assessed via the mean adequacy ratio (MAR/2000 kcal). In the observed series, only 9.7 FC on average (range 4-14) were fulfilled. In the simulated series: (i) MAR was positively associated with FC compliance level, with the highest MAR obtained with complete compliance; (ii) MAR decreased when meat or fish-based dishes were replaced by dishes without meat or fish; and (iii) removing the protein dish without replacement led to the lowest MAR. This study demonstrates that French school food guidelines ensure good nutritional quality of food services. It also shows that generalizing the service of meals without meat or fish would deteriorate overall nutritional quality, highlighting the need to define the composition of vegetarian dishes and their frequency of service to children.

  3. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

    Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron; Bradley, Richard F.; DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S.; Aguirre, James E.; Kohn, Saul A.; Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C.; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J.

    2016-01-01

    The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m 2 in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

  4. Optical analysis and performance evaluation of a solar parabolic dish concentrator

    Pavlović Saša R.

    2016-01-01

    Full Text Available In this study, the optical design of a solar parabolic dish concentrator is presented. The parabolic dish concentrator consists from 11 curvilinear trapezoidal reflective petals made of polymethyl methacrylate with special reflective coating. The dish diameter is equal to 3.8 m and the theoretical focal point distance is 2.26 m. Numerical simulations are made with the commercial software TracePro from Lambda Research, USA, and the final optimum position between absorber and reflector was calculated to 2.075 m; lower than focus distance. This paper presents results for the optimum position and the optimum diameter of the receiver. The decision for selecting these parameters is based on the calculation of the total flux over the flat and corrugated pipe receiver surface; in its central region and in the peripheral region. The simulation results could be useful reference for designing and optimizing of solar parabolic dish concentrators as for as for CFD analysis, heat transfer and fluid flow analysis in corrugated spiral heat absorbers. [Projekat Ministarstva nauke Republike Srbije, br. III42006: Research and development of energy and environmentally highly effective polygeneration systems based on renewable energy resources i br. III45016: Fabrication and characterization of nanophotonic functional structures in biomedicine and informatics

  5. Mobile Satellite Reception with a Virtual Satellite Dish based on a Reconfigurable Multi-Processor Architecture

    van de Burgwal, M.D.; Rovers, K.C.; Blom, K.C.H.; Kokkeler, Andre B.J.; Smit, Gerardus Johannes Maria

    2011-01-01

    Traditionally, mechanically steered dishes or analog phased array beamforming systems have been used for radio frequency receivers, where strong directivity and high performance were much more important than low-cost requirements. Real-time controlled digital phased array beamforming could not be

  6. Healthier side dishes at restaurants: an analysis of children’s perspectives, menu content, and energy impacts

    2014-01-01

    Background Children consume restaurant-prepared foods at high rates, suggesting that interventions and policies targeting consumption of these foods have the potential to improve diet quality and attenuate excess energy intake. One approach to encouraging healthier dietary intake in restaurants is to offer fruits and vegetables (FV) as side dishes, as opposed to traditional, energy-dense accompaniments like French fries. The aims of the current study were to examine: children's views about healthier side dishes at restaurants; current side dish offerings on children's menus at leading restaurants; and potential energy reductions when substituting FV side dishes in place of French fries. Methods To investigate children’s attitudes, a survey was administered to a nationally representative sample of U.S. 8- to 18-year-olds (n = 1178). To examine current side dish offerings, children's menus from leading quick service (QSR; n = 10) and full service restaurant chains (FSR; n = 10) were analyzed. Energy reductions that could result from substituting commonly-offered FV side dishes for French fries were estimated using nutrition information corresponding to the children's menu items. Results Two-thirds of children reported that they would not feel negatively about receiving FV sides instead of French fries with kids' meals. Liking/taste was the most common reason that children gave to explain their attitudes about FV side dishes. Nearly all restaurants offered at least 1 FV side dish option, but at most restaurants (60% of QSR; 70% of FSR), FV sides were never served by default. Substituting FV side dishes for French fries yielded an average estimated energy reduction of at least 170 calories. Conclusions Results highlight some healthy trends in the restaurant context, including the majority of children reporting non-negative attitudes about FV side dishes and the consistent availability of FV side dish options at leading QSR and FSR. Yet the minority of

  7. Negative-ion beam surface modification of tissue-culture polystyrene dishes for changing hydrophilic and cell-attachment properties

    Tsuji, H.; Satoh, H.; Ikeda, S.; Ikemura, S.; Gotoh, Y.; Ishikawa, J.

    1999-01-01

    Negative-silver-ion implantation into tissue-culture polystyrene (TCPS) dishes was investigated and it was found to modify hydrophilic and cell attachment properties of the dishes. Negative-ion implantation has an advantage of being almost free of surface charging, and is a suitable method for implantation into insulators such as polymers. Negative silver ions are used due to the antibacterial property of silver. Ag-implanted TCPS dishes had a contact angle larger than the normal value of 66 deg. of unimplanted dishes. The contact angle of water had a strong dependence on the ion energy rather than the dose. As a cell-culture experiment, human umbilical vascular endothelial cell (HUVEC) was used in unimplanted and Ag-implanted TCPS dishes, the implantation removed the cell-attachment property of the surface. In implantation with a mask with a striped pattern, most attached cells of HUVEC were in the unimplanted region aligned along a stripe direction

  8. Seismic design technology for breeder reactor structures. Volume 2. Special topics in soil/structure interaction analyses

    Reddy, D.P.

    1983-04-01

    This volume is divided into six chapters: definition of seismic input ground motion, review of state-of-the-art procedures, analysis guidelines, rock/structure interaction analysis example, comparison of two- and three-dimensional analyses, and comparison of analyses using FLUSH and TRI/SAC Codes

  9. The use of exploratory analyses within the National Institute for Health and Care Excellence single technology appraisal process: an evaluation and qualitative analysis.

    Kaltenthaler, Eva; Carroll, Christopher; Hill-McManus, Daniel; Scope, Alison; Holmes, Michael; Rice, Stephen; Rose, Micah; Tappenden, Paul; Woolacott, Nerys

    2016-04-01

    As part of the National Institute for Health and Care Excellence (NICE) single technology appraisal (STA) process, independent Evidence Review Groups (ERGs) critically appraise the company submission. During the critical appraisal process the ERG may undertake analyses to explore uncertainties around the company's model and their implications for decision-making. The ERG reports are a central component of the evidence considered by the NICE Technology Appraisal Committees (ACs) in their deliberations. The aim of this research was to develop an understanding of the number and type of exploratory analyses undertaken by the ERGs within the STA process and to understand how these analyses are used by the NICE ACs in their decision-making. The 100 most recently completed STAs with published guidance were selected for inclusion in the analysis. The documents considered were ERG reports, clarification letters, the first appraisal consultation document and the final appraisal determination. Over 400 documents were assessed in this study. The categories of types of exploratory analyses included fixing errors, fixing violations, addressing matters of judgement and the ERG-preferred base case. A content analysis of documents (documentary analysis) was undertaken to identify and extract relevant data, and narrative synthesis was then used to rationalise and present these data. The level and type of detail in ERG reports and clarification letters varied considerably. The vast majority (93%) of ERG reports reported one or more exploratory analyses. The most frequently reported type of analysis in these 93 ERG reports related to the category 'matters of judgement', which was reported in 83 (89%) reports. The category 'ERG base-case/preferred analysis' was reported in 45 (48%) reports, the category 'fixing errors' was reported in 33 (35%) reports and the category 'fixing violations' was reported in 17 (18%) reports. The exploratory analyses performed were the result of issues

  10. Health technologies for the improvement of chronic disease management: a review of the Medical Advisory Secretariat evidence-based analyses between 2006 and 2011.

    Nikitovic, M; Brener, S

    2013-01-01

    As part of ongoing efforts to improve the Ontario health care system, a mega-analysis examining the optimization of chronic disease management in the community was conducted by Evidence Development and Standards, Health Quality Ontario (previously known as the Medical Advisory Secretariat [MAS]). The purpose of this report was to identify health technologies previously evaluated by MAS that may be leveraged in efforts to optimize chronic disease management in the community. The Ontario Health Technology Assessment Series and field evaluations conducted by MAS and its partners between January 1, 2006, and December 31, 2011. Technologies related to at least 1 of 7 disease areas of interest (type 2 diabetes, coronary artery disease, atrial fibrillation, chronic obstructive pulmonary disease, congestive heart failure, stroke, and chronic wounds) or that may greatly impact health services utilization were reviewed. Only technologies with a moderate to high quality of evidence and associated with a clinically or statistically significant improvement in disease management were included. Technologies related to other topics in the mega-analysis on chronic disease management were excluded. Evidence-based analyses were reviewed, and outcomes of interest were extracted. Outcomes of interest included hospital utilization, mortality, health-related quality of life, disease-specific measures, and economic analysis measures. Eleven analyses were included and summarized. Technologies fell into 3 categories: those with evidence for the cure of chronic disease, those with evidence for the prevention of chronic disease, and those with evidence for the management of chronic disease. The impact on patient outcomes and hospitalization rates of new health technologies in chronic disease management is often overlooked. This analysis demonstrates that health technologies can reduce the burden of illness; improve patient outcomes; reduce resource utilization intensity; be cost

  11. Status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators

    Pointner, Winfried; Cuesta Morales, Alejandra; Draeger, Peer; Hartung, Juergen; Jakubowski, Zygmunt; Meyer, Gerhard; Palazzo, Simone; Moner, Guim Pallas; Perin, Yann; Pasichnyk, Ihor

    2014-07-01

    The scope of the work was to elaborate the prerequisites for short term accident analyses including recommendations for the application of new methodologies and computational procedures and technical aspects of safety evaluation. The following work packages were performed: Knowledge base for best estimate accident analyses; analytical studies on the PWR plant behavior in case of multiple safety system failures; extension and maintenance of the data base for plant specific analysis simulators.

  12. Analysing the past and exploring the future of sustainable biomass. Participatory stakeholder dialogue and technological innovation systems research

    Breukers, S.; Hisschemöller, M.; Cuppen, E.; Suurs, R.

    2014-01-01

    This paper explores the potential of combining technological innovation systems research with a participatory stakeholder dialogue, using empirical material from a dialogue on the options of sustainable biomass in the Netherlands and several historical studies into the emerging Dutch biomass

  13. Analysing Changes in Electricity Industries Against Actors and Technologies: Utility to Business Transformations in Denmark, Germany, Finland and Spain

    Mari Ratinen

    2012-07-01

    Full Text Available Liberalization of electricity markets, governmental policies for renewable electricity and technology development are transforming national electricity industries. However, there are considerable national differences in how these industries have changed and which businesses have been developed. We propose a typology for comparing changes in electricity industry based on the changes in the actors and technologies. Wind power and solar photovoltaic are used here as technology examples. A qualitative analysis of the changes in electricity industries in four EU member states is presented. Based on the preliminary findings, we conclude that if the industry consists of many, small firms with relatively loose ties with the government the industry is more likely to change than if it consists of few large firms with strong relations with the government.

  14. Scientometric and patentometric analyses to determine the knowledge landscape in innovative technologies: The case of 3D bioprinting.

    Rodríguez-Salvador, Marisela; Rio-Belver, Rosa María; Garechana-Anacabe, Gaizka

    2017-01-01

    This research proposes an innovative data model to determine the landscape of emerging technologies. It is based on a competitive technology intelligence methodology that incorporates the assessment of scientific publications and patent analysis production, and is further supported by experts' feedback. It enables the definition of the growth rate of scientific and technological output in terms of the top countries, institutions and journals producing knowledge within the field as well as the identification of main areas of research and development by analyzing the International Patent Classification codes including keyword clusterization and co-occurrence of patent assignees and patent codes. This model was applied to the evolving domain of 3D bioprinting. Scientific documents from the Scopus and Web of Science databases, along with patents from 27 authorities and 140 countries, were retrieved. In total, 4782 scientific publications and 706 patents were identified from 2000 to mid-2016. The number of scientific documents published and patents in the last five years showed an annual average growth of 20% and 40%, respectively. Results indicate that the most prolific nations and institutions publishing on 3D bioprinting are the USA and China, including the Massachusetts Institute of Technology (USA), Nanyang Technological University (Singapore) and Tsinghua University (China), respectively. Biomaterials and Biofabrication are the predominant journals. The most prolific patenting countries are China and the USA; while Organovo Holdings Inc. (USA) and Tsinghua University (China) are the institutions leading. International Patent Classification codes reveal that most 3D bioprinting inventions intended for medical purposes apply porous or cellular materials or biologically active materials. Knowledge clusters and expert drivers indicate that there is a research focus on tissue engineering including the fabrication of organs, bioinks and new 3D bioprinting systems. Our

  15. R and D 2005-2015. Energy efficient technologies - analysis; F og U 2005 - 2015. Energieffektive teknologier - analyse

    NONE

    2005-07-01

    The Danish Energy Authority has initiated the making of a strategy that includes research and development efforts within energy efficient technologies in a 10-year perspective. The strategy prioritizes and describes the research and development efforts with a view to obtain the largest possible effect from public funds. Furthermore, the objective is to create synergy between activities and players. This report is part of the second phase of the strategy project. The objective of this phase is to: 1. Lay the groundwork for prioritization, 2. Perform overall priorities, and 3. Draw up road maps for future R and D efforts within energy efficient technologies. (BA)

  16. Large Deployable Reflector (LDR) system concept and technology definition study. Volume 1: Executive summary, analyses and trades, and system concepts

    Agnew, Donald L.; Jones, Peter A.

    1989-01-01

    A study was conducted to define reasonable and representative large deployable reflector (LDR) system concepts for the purpose of defining a technology development program aimed at providing the requisite technological capability necessary to start LDR development by the end of 1991. This volume includes the executive summary for the total study, a report of thirteen system analysis and trades tasks (optical configuration, aperture size, reflector material, segmented mirror, optical subsystem, thermal, pointing and control, transportation to orbit, structures, contamination control, orbital parameters, orbital environment, and spacecraft functions), and descriptions of three selected LDR system concepts. Supporting information is contained in appendices.

  17. A microfluidic-based lid device for conventional cell culture dishes to automatically control oxygen level.

    Lee, Seung Yeob; Yang, Sung

    2018-04-25

    Most conventional hypoxic cell culture systems undergo reoxygenation during experimental manipulations, resulting in undesirable effects including the reduction of cell viability. A lid device was developed herein for conventional cell culture dishes to resolve this limitation. The integration of multilayered microfluidic channels inside a thin membrane was designed to prevent the reoxygenation caused by reagent infusion and automatically control the oxygen level. The experimental data clearly show the reducibility of the dissolved oxygen in the infusing reagent and the controllability of the oxygen level inside the dish. The feasibility of the device for hypoxia studies was confirmed by HIF-1α experiments. Therefore, the device could be used as a compact and convenient hypoxic cell culture system to prevent reoxygenation-related issues.

  18. Effect of radiation on preservation of convenient dish 'bowl-shape packed pig elbow'

    Wang Keqin; Chen Jingping; Li Wenge; Peng Weizheng

    2005-01-01

    The suitable parameters for radiation processing were investiqated by analyzing the microload of material and product, and radiation effect on the preservation of convenient dish 'bowl-shape packed pig elbow'. The results showed the store period of the product could be extended 2-6 month by 4.0-6.0 kGy radiation at different storage temperature. The sensory, physical and chemical index of the products met the requirement of relevant national standard of food hygiene. (authors)

  19. Who should do the dishes now? Revisiting gender and housework in contemporary urban South Wales

    Mannay, Dawn

    2016-01-01

    This chapter revisits Jane Pilcher’s (1994) seminal work ‘Who should do the dishes? Three generations of Welsh women talking about men and housework’, which was originally published in Our Sister’s Land: the changing identities of women in Wales. As discussed in the introductory chapter, I began revisiting classic Welsh studies as part of my doctoral study Mothers and daughters on the margins: gender, generation and education (Mannay, 2012); this lead to the later publication of a revisiting ...

  20. Modeling the small-scale dish-mounted solar thermal Brayton cycle

    Le Roux, Willem G.; Meyer, Josua P.

    2016-05-01

    The small-scale dish-mounted solar thermal Brayton cycle (STBC) makes use of a sun-tracking dish reflector, solar receiver, recuperator and micro-turbine to generate power in the range of 1-20 kW. The modeling of such a system, using a turbocharger as micro-turbine, is required so that optimisation and further development of an experimental setup can be done. As a validation, an analytical model of the small-scale STBC in Matlab, where the net power output is determined from an exergy analysis, is compared with Flownex, an integrated systems CFD code. A 4.8 m diameter parabolic dish with open-cavity tubular receiver and plate-type counterflow recuperator is considered, based on previous work. A dish optical error of 10 mrad, a tracking error of 1° and a receiver aperture area of 0.25 m × 0.25 m are considered. Since the recuperator operates at a very high average temperature, the recuperator is modeled using an updated ɛ-NTU method which takes heat loss to the environment into consideration. Compressor and turbine maps from standard off-the-shelf Garrett turbochargers are used. The results show that for the calculation of the steady-state temperatures and pressures, there is good comparison between the Matlab and Flownex results (within 8%) except for the recuperator outlet temperature, which is due to the use of different ɛ-NTU methods. With the use of Matlab and Flownex, it is shown that the small-scale open STBC with an existing off-the-shelf turbocharger could generate a positive net power output with solar-to-mechanical efficiency of up to 12%, with much room for improvement.

  1. Finite time thermodynamic analysis and optimization of solar-dish Stirling heat engine with regenerative losses

    Sharma Arjun

    2011-01-01

    Full Text Available The present study investigates the performance of the solar-driven Stirling engine system to maximize the power output and thermal efficiency using the non-linearized heat loss model of the solar dish collector and the irreversible cycle model of the Stirling engine. Finite time thermodynamic analysis has been done for combined system to calculate the finite-rate heat transfer, internal heat losses in the regenerator, conductive thermal bridging losses and finite regeneration process time. The results indicate that exergy efficiency of dish system increases as the effectiveness of regenerator increases but decreases with increase in regenerative time coefficient. It is also found that optimal range of collector temperature and corresponding concentrating ratio are 1000 K~1400 K and 1100~1400, respectively in order to get maximum value of exergy efficiency. It is reported that the exergy efficiency of this dish system can reach the maximum value when operating temperature and concentrating ratio are 1150 K and 1300, respectively.

  2. Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

    Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

    2014-01-01

    In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell–NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment. (paper)

  3. Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

    Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

    2014-05-01

    In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell-NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment.

  4. Cascade system using both trough system and dish system for power generation

    Zhang, Cheng; Zhang, Yanping; Arauzo, Inmaculada; Gao, Wei; Zou, Chongzhe

    2017-01-01

    Highlights: • A novel solar cascade system using both trough and dish collectors is proposed. • Heat rejected by the Stirling engines is collected by the condensed water. • The directions to increase the efficiency improvement has been pointed out • Influence of flow type of heating/cooling fluids of Stirling engines is considered. - Abstract: This paper represents a novel solar thermal cascade system using both trough and dish systems for power generation. An effective structure using the condensed fluid of Rankine cycle to cool the Stirling engines to use the heat released by Stirling engines was proposed. The cascade system model with different fluid circuits was developed. The models of some important components of the system, such as dish collector, trough collector and Stirling engine array, are presented with detail explanation in this paper. Corresponding stand-alone systems were also developed for comparison. Simulations were conducted with the models to find out efficiency difference between cascade system and corresponding stand-alone systems. The directions to increase the efficiency difference were also considered. Results show that the cascade system can achieve a higher efficiency with a high solar irradiance (>550 W/m"2). The flow type of fluids between heating and cooling Stirling engine array is also required to concern on designing a cascade system with Stirling engine array.

  5. Nutritional value of traditional Italian meat-based dishes: influence of cooking methods and recipe formulation.

    D'Evoli, L; Salvatore, P; Lucarini, M; Nicoli, S; Aguzzi, A; Gabrielli, P; Lombardi-Boccia, G

    2009-01-01

    The present study provides a picture of the compositional figure and nutritive value of meat-based dishes typical of Italian culinary tradition. Recipes specific for a bovine meat cut (top-side) were selected among the most widespread ones in Italy: in pan, pizzaiola, cutlet, meat ball, and escalope. The total fat and cholesterol content varied depending on the ingredients utilized (extra-virgin olive oil, parmesan, egg). Meat-based dishes that utilized extra-virgin olive oil showed a significant reduction in palmitic and stearic acids and a parallel increase in oleic acid compared with raw meat; furthermore, the ratio among saturated fatty acids, monounsaturated fatty acids and polyunsaturated fatty acids shifted in favour of monounsaturated fatty acids. B vitamins were affected at different extent by heating; by contrast, vitamin E content increased because of the new sources of this vitamin, which masked losses due to heating. Ingredients (parmesan, discretionary salt) induced significant increases in the calcium and sodium concentrations compared with raw meat. The total iron content did not show marked differences in most of the meat-based dishes compared with raw meat; by contrast, losses in the heme-iron concentration were detected depending on the severity of heating treatments. Our findings suggest that heme iron, because of its important health aspects, might be a useful index of the nutritional quality of cooked meats.

  6. Human tissues in a dish : The research and ethical implications of organoid technology

    Bredenoord, Annelien L.; Clevers, Hans; Knoblich, Juergen A.

    2017-01-01

    The ability to generate human tissues in vitro from stem cells has raised enormous expectations among the biomedical research community, patients, and the general public. These organoids enable studies of normal development and disease and allow the testing of compounds directly on human tissue.

  7. RELIGION, TECHNOLOGY AND SOCIAL CHANGE: REPRESENTATIONS OF MUSLIM WORLD IN ACADEMIC ANALYSES OF THE ROLE OF SOCIAL MEDIA IN THE ARAB SPRING

    Adeela Arshad Ayaz

    2015-03-01

    Full Text Available This article deconstructs the dominant constructions and portrayals of the Muslim world in literature on social media and civic engagement in relation to the Arab Spring. A critical reading of literature on social media and ‘Arab Spring’ shows that analyses by Western scholars and commentators are still grounded in ‘modernist dualism’ and orientalist understandings. The article starts by tracing the history of technology to argue that analyses of social media’s educational and civic potential within the Western context in general, is continuation of arguments about earlier technologies in relation to societal development. However, when it comes to analyzing social media and civic engagement particularly in the Muslim world this tendency gets muddled with another well-established trend, that of Orientalism. The overall impact of this tendency results in restricting majority of arguments within the essentialists/determinists paradigm. Such analyses essentialize the technological aspects of social media as universal and constitute the West as civilized, democratic, multicultural, and progressive. On the other hand Muslim world is represented as uncivilized, undemocratic, uncultured, and chained in past traditions. Thus, there is a need for a nuanced understanding of the relationship between the social media and civic engagement in the Muslim world, which can be conceptualized by framing the issues within a postcolonial critique of neoliberal globalization. DOI: 10.15408/tjems.v1i2.1264

  8. Cacophony or Empowerment? Analysing the Impact of New Information Communication Technologies and New Social Media in Southeast Asia

    Jason P. Abbott

    2011-01-01

    Full Text Available The capabilities, tools and websites we associate with new information communication technologies and social media are now ubiquitous. Moreover tools that were designed to facilitate innocuous conversation and social interaction have had unforeseen political impacts. Nowhere was this more visible than during the 2011 uprisings across the Arab World. From Tunis to Cairo, and Tripoli to Damascus protest movements against authoritarian rule openly utilized social networking and file sharing tools to publicize and organize demonstrations and to catalogue human rights abuses. The Arab Spring, or Jasmine Revolution, was an event that was both witnessed and played out in real time online. This article explores the impacts and effects of these technologies on regimes in East Asia, in particular exploring the extent to which they proffer new capabilities upon activists and reformers in the region’s semi-democratic and authoritarian regimes. Drawing on data on Internet and smartphone use, as well as case studies that explore the role of these technologies on the 2008 and 2011 general elections in Malaysia and Singapore respectively, this article suggests that the Internet and social networking platforms do present unique opportunities for activists, citizens and social movements.

  9. Analysing socioeconomic diversity and scaling effects on residential electricity load profiles in the context of low carbon technology uptake

    McKenna, R.; Hofmann, L.; Merkel, E.; Fichtner, W.; Strachan, N.

    2016-01-01

    Adequately accounting for interactions between Low Carbon Technologies (LCTs) at the building level and the overarching energy system means capturing the granularity associated with decentralised heat and power supply in residential buildings. The approach presented here adds novelty in terms of a realistic socioeconomic differentiation by employing dwelling/household archetypes (DHAs) and neighbourhood clusters at the Output Area (OA) level. These archetypes are combined with a mixed integer linear program (MILP) to generate optimum (minimum cost) technology configurations and operation schedules. Even in the baseline case, without any LCT penetration, a substantial deviation from the standard load profile (SLP) is encountered, suggesting that for some neighbourhoods this profile is not appropriate. With the application of LCTs, including heat pumps, micro-CHP and photovoltaic (PV), this effect is much stronger, including more negative residual load, more variability, and higher ramps with increased LCT penetration, and crucially different between neighbourhood clusters. The main policy implication of the study is the importance of understanding electrical load profiles at the neighbourhood level, because of the consequences they have for investment in the overarching energy system, including transmission and distribution infrastructure, and centralised generation plant. Further work should focus on attaining a superior socioeconomic differentiation between households. - Highlights: • Low carbon technologies (LCTs) for heat/electricity in residential buildings. • Socioeconomic effects and interactions with overarching energy system. • Building thermal/electrical model combined with optimisation. • Significant differences between neighbourhood load profiles. • Policy implications: support for LCTs and investment in infrastructure.

  10. Mount for continuously orienting a collector dish in a system adapted to perform both diurnal and seasonal solar tracking

    Brantley, L. W., Jr.; Lawson, B. D. (Inventor)

    1977-01-01

    A collector dish is continuously oriented toward the sun in a system adapted to perform both diurnal and seasonal solar tracking. The mount is characterized by a rigid, angulated axle having a linear midportion supporting a collector dish, and oppositely extended end portions normally related to the midportion of the axle and received in spaced journals. The longitudinal axis of symmetry for the midportion of the axle is coincident with a seasonal axis while the axes of the journals are coincident with a diurnal axis paralleling the earth's polar axis. Drive means are provided for periodically displacing the axle about the diurnal axis at a substantially constant rate, while other drive means are provided for periodically indexing the dish through 1 deg about the seasonal axis whereby the position of the dish relative to the axle is varied for accommodating seasonal tracking as changes in the angle of inclination of the polar axis occurs.

  11. Technological innovations and public politics: social environmental analyses in the context of sugar-ethanol industrial activities in Brazil

    Charlene Maria C. de Ávila Plaza

    2008-08-01

    Full Text Available The present article aims at discussing the importance of the technological innovations as propellers of the economic development of the nations as well as the role of the public politics directed toward the socioeconomics and institutional agents who are a part of the productive and innovative chain of the country. We try to analyze the sugar-ethanol sector and its consequences concerning the environmental aspects, being emphasized the State of Goiás and the “Cerrado” bioma. In the social aspects, we demonstrate the necessity to conciliate economic development with social-environmental sustainability, to propitiate a healthy environment and improvement of the working conditions and life for the citizens who perform the functions of sugar cane cutters of this sector. It is important to emphasize that the article does not intend to underestimate the economic practices of the sugar-ethanol companies, but to analyze certain aspects concerning the environment and the social factor, so that consistent politics is implemented in order to promote sustainability, balanced with enterprise and governmental responsibilities and commitments allied to the tripod: economy, environment and society. Key-words: Technological innovation; Public Politics; Sustainable Development; Sugar-ethanol Sector; Biofuels

  12. MODELLING OF AN INEXPENSIVE 9M SATELLITE DISH FROM 3D POINT CLOUDS CAPTURED BY TERRESTRIAL LASER SCANNERS

    D. Belton

    2012-09-01

    Full Text Available This paper presents the use of Terrestrial laser scanners (TLS to model the surface of satellite dish. In this case, the dish was an inexpensive 9m parabolic satellite dish with a mesh surface, and was to be utilised in radio astronomy. The aim of the modelling process was to determine the deviation of the surface away from its true parabolic shape, in order to estimate the surface efficiency with respect to its principal receiving frequency. The main mathematical problems were the optimal and unbiased estimation the orientation of the dish and the fitting of a parabola to the local orientation or coordinate system, which were done by both orthogonal and algebraic minimization using the least-squares method. Due to the mesh structure of the dish, a classification method was also applied to filter out erroneous points being influenced by the supporting structure behind the dish. Finally, a comparison is performed between the ideal parabolic shape, and the data collected from three different temporal intervals.

  13. Application of LiDAR technology in analyses of the topography of Margum/Morava and Kulič

    Ivanišević Vujadin

    2012-01-01

    Full Text Available Roman Margum and Mediaeval town of Morava, situated on the Orašje site in Dubravica at the confluence of the Velika Morava and the Danube, could not have been analysed more thoroughly in the past because of the damage caused by the river bed displacements and soil erosion on the one hand, and dense vegetation growing on such a moist terrain on the other. Archaeological research has so far failed to produce even a site plan. Available data on this important site are contradictory to a considerable extent, so the information one could obtain from the written and cartographic sources needed to be confronted with the archaeological ones and, especially, those derived from the recent LiDAR scanning of the terrain, conducted within the scope of the Archaeo-Landscapes Europe Project. Among the most important plans of the confluence area are those left by Marsigli in the 18th and Kanitz in the 19th century. Felix Kanitz, the famous Balkan traveler, also provided us with a textual description of his visit to the site in 1887. Our analyses of the two plans have revealed a number of inaccuracies. Through analyses of the obtaineded LiDAR scans, however, the preserved area of the two settlements has been clearly demarcated, measuring 7-8 hectares, and the eastern edge of the Roman agglomeration - presumed already in the course of the 2011 excavations - was confirmed. Most probably it was the eastern rampart of the Roman fortification. Apart from this, the purpose of a canal stretching along the whole plateau, and mentioned by Kanitz, has been established. Given that to the east of the canal there was the presumably Roman rampart, and to the west of it there were recently excavated ruins of Roman buildings, the canal itself must have been of a more recent date. Bearing in mind the established vertical stratigraphy of the site, we conclude that it was in fact a Mediaeval defence trench. The topography of the nearby fort Kulič has been studied as well. It is

  14. New MRI technologies. Diffusion MRI and its application to functional neuroimaging and analyses of white matter integrity

    Kobayashi, Tetsuo

    2010-01-01

    Described is the technological aspect of MRI, MR diffusion-weighted imaging (MR-DWI), principles of its measurement and application for imaging the cerebral function and for aiding the quantitative diagnosis of brain diseases. The author explains the principle of MR imaging process; diffusion properties of water molecules, MR-DWI based on them and DW-fMRI of the brain; MR-diffusion tensor imaging (MR-DTI), its analysis and color acquisition, and tracking of white matter nerve fibers; analysis of white matter lesions by the tracking; and the new tracking method at the chiasm of nerve fascicles. The usual fMRI reflects the blood oxygen level depending (BOLD) signals whereas recently attracted DW-fMRI, the volume changes of nerve cells concomitant to nerve activation accompanying apparent changes of water diffusion coefficients in and out of cells which occur faster than BOLD signs, resulting in higher resolution of time and space. However, DWI requires the higher intensity of static magnetic field like 3T. MR-DTI acquires the anisotropic diffusion of water molecules using MR-DWI technique with application of 6 or more motion probing gradients, thus makes it possible to track the running directions of nerve fibers and capillary vessels, and is proposed to be a useful mean of specific fiber tracking in the white matter when displayed by 3 different colors exhibiting the directions like the right/left (x axis, red), anterior/posterior (y, green) and upper/lower (z, blue) sides of head. Recently, MR-DWI and MR-DTI have been found usable for pathogenic studies of brain diseases such as dementia. Tensor anisotropy is apparently lowered at the chiasm of nerve fascicles, the cause of tracking error, for which authors have developed a new method using the similarity of directional vector, not of tensor, before and behind the chiasm. As exemplified, MRI technology is further advancing even at present. (T.T.)

  15. Facet development for a faceted stretched-membrane dish by Solar Kinetics, Inc

    Schertz, P.T.; Brown, D.C.; Konnerth, A. III (Solar Kinetics, Inc., Dallas, TX (United States))

    1991-07-01

    A 3.6-meter diameter stretched-membrane optical facet for a parabolic dish has been successfully designed and demonstrated under contract with Sandia National Laboratories. Twelve facets identical to them will be used to make the lightweight reflector of the dish. The project goal of 2.5-mrad surface accuracy was met with each of the two full-sized prototypes, and accuracies of as low as 1.1 mrad were achieved. The facet weight is 11.7 kg/m{sup 2} (2.4lbs/ft{sup 2}). The facet is similar in construction to the successful stretched-membrane heliostat; it has two thin metal membranes attached to a ring. However, the front membrane for this facet is plastically formed at the factor in order to achieve a shorter facet f/D (approximately 3.0). A passive tether restrains the from membrane when not in operation, that is, when the stabilizing vacuum is off. The optical surface is achieved with a silvered-acrylic film laminated to the metal membrane. The facet is expected to cost $55.40/m{sup 2} at a production rate of 10,000 facets per year and $115, 000/m{sup 2}-at a production rate of 500 facets a year. Several key issues have been resolved. Stress concentrations due to seams in the reflective laminate did not cause membrane rupture during forming as they have for dishes with lower focal length-to-diameter ratios. The laminate survived the forming process and simulated operation without deterioration. The optical effect of the tether on the membrane was tested and found to be very small. Most important, highly accurate shapes were obtained using a simple forming procedure. Additional tests are needed to demonstrate process repeatablility and facet performance in typical operating conditions. 18 refs., 36 figs., 11 tabs.

  16. Design and implementation of a 38 kW dish-Stirling concentrated solar power system

    Yan, J.; Peng, Y. D.; Cheng, Z. R.; Liu, F. M.; Tang, X. H.

    2017-11-01

    Dish-Stirling concentrated solar power system (DS-CSP) is an important pathway for converting solar energy into electricity at high efficiency. In this study, a rated power 38 kW DS-CSP system was developed (installed in Xiangtan Electric Manufacturing Group). The heat engine adopted the alpha-type four cylinders double-acting Stirling engine (Stirling Biopower Flexgen S260). The absorber flux distribution simulation was conducted using ray tracing method and then the 204 m2 parabolic dish concentrator system (diameter is 17.70 m and focal length is 9.49 m) with single concentrator plus single pillar supporting has been designed and built. A water-cooled disc target and an absorber imitation device were adopted to test the tracking performance of the dish concentrator system, homogeneity of the focal spot and flux distribution of the absorber. Finally, the S260 Stirling engine was installed on the focal position of the dish concentrator and then the net output power date of the 38 kW DS-CSP system was tested. The absorber overheating problem on the DS-CSP system performance was discussed when the DS-CSP system was installed in different locations. The testing result shows that this system achieved the net output power of 38 kW and solar-to-electricity efficiency (SEE) of 25.3% with the direct normal irradiation (DNI) at 750 W/m2. The net output power can further increase to 40.5 kW with the SEE of 26.6% when the DNI reaches up to the maximum of 761 W/m2. The net output power of the 38 kW DS-CSP system has a linear function relationship with the DNI. The fitting function is Net power output=0.1003×DNI-36.129, where DNI is at the range of 460∼761 W/m2. This function could be used to predict the amount of the 38 kW DS-CSP system annual generation power.

  17. Who should do the dishes now? exploring gender and housework in contemporary urban South Wales

    Mannay, Dawn

    2014-01-01

    This paper revisits Jane Pilcher’s (1994) seminal chapter from Our Sisters’ Land: The Changing Identities of Women in Wales - ‘Who should do the dishes? Three generations of Welsh women talking about men and housework’. Two decades on from the original study, the paper explores this question in contemporary south Wales by drawing upon data generated in a study of mothers and daughters residing in a Welsh, marginalised, urban housing area. Mothers of daughters in the two eldest groups tended t...

  18. Flavor Enhancer From Catfish (Clarias batrachus) Bekasam Powder and Angiotensin-I-Converting Enzyme (ACE) Inhibitory Activity in Various Dishes

    Lestari, Yanesti N.; Murwani, Retno; Agustini, Tri W.

    2018-02-01

    Flavor enhancer is characterized by high glutamic acid content and it can be obtained from fermented food such as Bekasam. Fermented food had inhibitory effect on Angiotensin-I-Converting Enzyme (ACE) activity which is advantageous for hypertension. However, such activity was not known to sustain in food system. The aim of this research was to study addition of flavour enhancer from Catfish Bekasam Powder (CBP) in various food systems and to determine the ACE inhibitory (ACEI) activity in the food system. Four food system consisted of carrot, champignon, and chicken meat dishes were boiled in water and added with CBP or MSG. Each food system was added with graded level of CBP (0%; 0.5%; 0.8%; 1.1%; and 1,4%) and for control monosodium glutamate (MSG) was used. ACEI activity in each food system and organoleptic test using multiple comparison differentiation on 15 semi-trained panellists were determined. The results showed that there were fluctuation of ACEI activity in the carrot, champignon, and chicken meat dishes (p=0.017; 0.043; and 0.032). The MSG containing dishes showed the lowest ACEI activity. Addition of graded level of CBP on carrot, champignon, and chicken meat dishes were directly proportional to glutamic acid content but inversely proportional to ACEI activity (pacid content but reduced ACE-inhibitory activity significantly (p<0.05). Comparing CBP to MSG addition in champignon dish revealed that increasing level of CBP increased the flavour preference of the panellists. On the contrary the higher the addition CBP in noodle and chicken meat dishes the worse were the flavour score (p<0.05). It can be concluded that the addition of CBP as flavour enhancer on various dishes can deliver better flavour and ACE-inhibitory activity than the addition of commercial MSG.

  19. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Tunma, Somruthai; Song, Doo-Hoon; Kim, Si-Eun; Kim, Kyoung-Nam; Han, Jeon-Geon; Boonyawan, Dheerawan

    2013-01-01

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N 2 films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiO x films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV–vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of -NH 2 groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  20. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Tunma, Somruthai; Song, Doo-Hoon; Kim, Si-Eun; Kim, Kyoung-Nam; Han, Jeon-Geon; Boonyawan, Dheerawan

    2013-10-01

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N2 films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiOx films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV-vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of sbnd NH2 groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  1. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Tunma, Somruthai [The Graduate School, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Song, Doo-Hoon [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Kim, Si-Eun; Kim, Kyoung-Nam [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Department and Research Institute of Dental Biomaterials and Bioengineering, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Han, Jeon-Geon [Center for Advanced Plasma Surface Technology, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon 440-746 (Korea, Republic of); Boonyawan, Dheerawan [Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand)

    2013-10-15

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N{sub 2} films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiO{sub x} films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV–vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of -NH{sub 2} groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  2. Nutritional composition of commonly consumed composite dishes from rural villages in Empangeni, KwaZulu-Natal, South Africa.

    Spearing, K; Kolahdooz, F; Lukasewich, M; Mathe, N; Khamis, T; Sharma, S

    2013-06-01

    Accurate nutrient composition data for composite dishes unique to a population is essential for the development of a nutrient database and the calculation of dietary intake. The present study aimed to provide the nutritional composition of composite dishes frequently consumed in rural KwaZulu-Natal, South Africa. Commonly consumed composite dishes were identified using 24-h recalls collected from 79 randomly selected community members. Multiple recipes were collected for each reported dish. The mean nutritional composition of each dish was calculated per 100 g using the nutribase clinical nutrition manager (Cybersoft Inc., Phoenix, AZ, USA). A total of 79 recipes were collected for 16 commonly consumed dishes (seven meat-based, five starch-based and four legume/vegetable-based). 'Fried chicken' contained the most energy [1469 kJ (351 kcal)], protein (29.7 g), fat (23.7 g), cholesterol (123 mg) and niacin (8.4 mg). 'Fried beef' contained the most potassium (495 mg) and zinc (6.4 mg), whereas 'fish stew' had the most vitamin D (4.2 μg) and calcium (215 mg). 'Fried cabbage' and 'fried spinach' contained the largest percent energies from fat, at 79% and 76%, respectively. A traditional sweet bread, 'jeqe', made with fortified flour contributed significantly to iron (4.6 mg), niacin (4.5 μg) and folate (129 μg). The sodium content of dishes ranged from 88 to 679 mg per 100 g. The nutritional composition data for commonly consumed dishes in rural KwaZulu-Natal is presented. Although the dishes are good sources of protein, vitamins and minerals, they also contain substantial amounts of fat. This culturally appropriate information will enable the calculation of dietary intake and can be used to encourage the consumption of recipes rich in key nutrients. © 2012 The Authors Journal of Human Nutrition and Dietetics © 2012 The British Dietetic Association Ltd.

  3. Design, simulation and optimization of a solar dish collector with spiral-coil thermal absorber

    Pavlović Saša R.

    2016-01-01

    Full Text Available The efficient conversion of solar radiation into heat at high temperature levels requires the use of concentrating solar collectors. The goal of this paper is to present the optical and the thermal analysis of a parabolic dish concentrator with a spiral coil receiver. The parabolic dish reflector consists of 11 curvilinear trapezoidal reflective petals constructed by PMMA with silvered mirror layer and has a diameter of 3.8 m, while its focal distance is 2.26m. This collector is designed with commercial software SolidWorks and simulated, optically and thermally in its Flow Simulation Studio. The optical analysis proved that the ideal position of the absorber is at 2.1m from the reflector in order to maximize the optical efficiency and to create a relative uniform heat flux over the absorber. In thermal part of the analysis, the energetic efficiency was calculated approximately 65%, while the exergetic efficiency is varied from 4% to 15% according to the water inlet temperature. Moreover, other important parameters as the heat flux and temperature distribution over the absorber are presented. The pressure drop of the absorber coil is calculated at 0.07bar, an acceptable value.

  4. Embryo density may affect embryo quality during in vitro culture in a microwell group culture dish.

    Lehner, Adam; Kaszas, Zita; Murber, Akos; Rigo, Janos; Urbancsek, Janos; Fancsovits, Peter

    2017-08-01

    Culturing embryos in groups is a common practice in mammalian embryology. Since the introduction of different microwell dishes, it is possible to identify oocytes or embryos individually. As embryo density (embryo-to-volume ratio) may affect the development and viability of the embryos, the purpose of this study was to assess the effect of different embryo densities on embryo quality. Data of 1337 embryos from 228 in vitro fertilization treatment cycles were retrospectively analyzed. Embryos were cultured in a 25 μl microdrop in a microwell group culture dish containing 9 microwells. Three density groups were defined: Group 1 with 2-4 (6.3-12.5 μl/embryo), Group 2 with 5-6 (4.2-5.0 μl/embryo), and Group 3 with 7-9 (2.8-3.6 μl/embryo) embryos. Proportion of good quality embryos was higher in Group 2 on both days (D2: 18.9 vs. 31.5 vs. 24.7%; p Culturing 5-6 embryos together in a culture volume of 25 μl may benefit embryo quality. As low egg number, position, and distance of the embryos may influence embryo quality, results should be interpreted with caution.

  5. Analysis of solar water heater with parabolic dish concentrator and conical absorber

    Rajamohan, G.; Kumar, P.; Anwar, M.; Mohanraj, T.

    2017-06-01

    This research focuses on developing novel technique for a solar water heating system. The novel solar system comprises a parabolic dish concentrator, conical absorber and water heater. In this system, the conical absorber tube directly absorbs solar radiation from the sun and the parabolic dish concentrator reflects the solar radiations towards the conical absorber tube from all directions, therefore both radiations would significantly improve the thermal collector efficiency. The working fluid water is stored at the bottom of the absorber tubes. The absorber tubes get heated and increases the temperature of the working fluid inside of the absorber tube and causes the working fluid to partially evaporate. The partially vaporized working fluid moves in the upward direction due to buoyancy effect and enters the heat exchanger. When fresh water passes through the heat exchanger, temperature of the vapour decreases through heat exchange. This leads to condensation of the vapour and forms liquid phase. The working fluid returns to the bottom of the collector absorber tube by gravity. Hence, this will continue as a cyclic process inside the system. The proposed investigation shows an improvement of collector efficiency, enhanced heat transfer and a quality water heating system.

  6. Validation of a Dish-Based Semiquantitative Food Questionnaire in Rural Bangladesh

    Pi-I. D. Lin

    2017-01-01

    Full Text Available A locally validated tool was needed to evaluate long-term dietary intake in rural Bangladesh. We assessed the validity of a 42-item dish-based semi-quantitative food frequency questionnaire (FFQ using two 3-day food diaries (FDs. We selected a random subset of 47 families (190 participants from a longitudinal arsenic biomonitoring study in Bangladesh to administer the FFQ. Two 3-day FDs were completed by the female head of the households and we used an adult male equivalent method to estimate the FD for the other participants. Food and nutrient intakes measured by FFQ and FD were compared using Pearson’s and Spearman’s correlation, paired t-test, percent difference, cross-classification, weighted Kappa, and Bland–Altman analysis. Results showed good validity for total energy intake (paired t-test, p < 0.05; percent difference <10%, with no presence of proportional bias (Bland–Altman correlation, p > 0.05. After energy-adjustment and de-attenuation for within-person variation, macronutrient intakes had excellent correlations ranging from 0.55 to 0.70. Validity for micronutrients was mixed. High intraclass correlation coefficients (ICCs were found for most nutrients between the two seasons, except vitamin A. This dish-based FFQ provided adequate validity to assess and rank long-term dietary intake in rural Bangladesh for most food groups and nutrients, and should be useful for studying dietary-disease relationships.

  7. Primary Beam and Dish Surface Characterization at the Allen Telescope Array by Radio Holography

    Harp, G. R.; Ackermann, R. F.; Nadler, Z. J.; Blair, Samantha K.; Davis, M. M.; Wright, M. C. H.; Forster, J. R.; Deboer, D. R.; Welch, W. J.; Atkinson, Shannon; Backer, D. C.; Backus, P. R.; Barott, William; Bauermeister, Amber; Blitz, Leo; Bock, D. C.-J.; Bower, Geoffrey C.; Bradford, Tucker; Cheng, Calvin; Croft, Steve; Dexter, Matt; Dreher, John; Engargiola, Greg; Fields, E. D.; Heiles, Carl; Helfer, Tamara; Jordan, Jane; Jorgensen, Susan; Kilsdonk, Tom; Gutierrez-Kraybill, Colby; Keating, Garrett; Law, Casey; Lugten, John; MacMahon, D. H. E.; McMahon, Peter; Milgrome, Oren; Siemion, Andrew; Smolek, Ken; Thornton, Douglas; Pierson, Tom; Randall, Karen; Ross, John; Shostak, Seth; Tarter, J. C.; Urry, Lynn; Werthimer, Dan; Williams, Peter K. G.; Whysong, David

    2011-06-01

    The Allen Telescope Array (ATA) is a cm-wave interferometer in California, comprising 42 antenna elements with 6-m diameter dishes. We characterize the antenna optical accuracy using two-antenna interferometry and radio holography. The distortion of each telescope relative to the average is small, with RMS differences of 1% of beam peak value. Holography provides images of dish illumination, characterizing as-built mirror surfaces. Maximal distortions across ~ 2 meter lengths appear to result from mounting stresses or solar radiation. Experimental RMS errors are 0.7 mm at night and 3 mm under worst-case solar illumination. For frequencies 4, 10, and 15 GHz, the nighttime values indicate sensitivity losses of 1, 10 and 20%, respectively. ATA's wide-bandwidth receiver permits observations over a continuous range 0.5-11.2 GHz. We probe the antenna optical gain and beam pattern stability as a function of focus position and observation frequency, concluding that ATA can produce high fidelity images over a decade of simultaneous observation frequencies. We quantify solar heating effects on antenna sensitivity and pointing accuracy. We find that during the day, observations >=5 GHz will suffer some sensitivity loss and it may be necessary to make antenna pointing corrections on a 1-2 hourly basis.

  8. Modification of parabolic dish antenna pattern using two symmetrically placed circular flat plates

    Thorpe, Glen C.

    1987-12-01

    This study aims to formulate a method of predicting the far field pattern of a parabolic dish antenna with two moveable flat plates mounted symmetrically on either side of the feed horn. The approach taken has been to first analyze the radiation pattern of the antenna with the disks at certain heights out from the surface of the dish. To do this the near-field radiation in amplitude and phase was measured over a plane surface in the near-field and the values were then transformed into the far field using a Fast Fourier Transform. Far field pattern values of the antenna were directly measured for each setting of the plates. The results obtained from the Fast Fourier Transform of the near field data were in good agreement with the values obtained by measurement. Finally, an approximate model of the antenna was developed and implemented as a computer program. This model, while relatively unsophisticated, provided some insights into the changes in the near field phase distribution caused by the moveable circular flat plates.

  9. Effect of Tracking Error of Double-Axis Tracking Device on the Optical Performance of Solar Dish Concentrator

    Jian Yan

    2018-01-01

    Full Text Available In this paper, a flux distribution model of the focal plane in dish concentrator system has been established based on ray tracking method. This model was adopted for researching the influence of the mirror slope error, solar direct normal irradiance, and tracking error of elevation-azimuth tracking device (EATD on the focal spot characteristics (i.e., flux distribution, geometrical shape, centroid position, and intercept factor. The tracking error transmission law of the EATD transferred to dish concentrator was also studied. The results show that the azimuth tracking error of the concentrator decreases with the increase of the concentrator elevation angle and it decreases to 0 mrad when the elevation angle is 90°. The centroid position of focal spot along x-axis and y-axis has linear relationship with azimuth and elevation tracking error of EATD, respectively, which could be used to evaluate and calibrate the tracking error of the dish concentrator. Finally, the transmission law of the EATD azimuth tracking error in solar heliostats is analyzed, and a dish concentrator using a spin-elevation tracking device is proposed, which can reduce the effect of spin tracking error on the dish concentrator. This work could provide fundamental for manufacturing precision allocation of tracking devices and developing a new type of tracking device.

  10. Performance tests and efficiency analysis of Solar Invictus 53S - A parabolic dish solar collector for direct steam generation

    Jamil, Umer; Ali, Wajahat

    2016-05-01

    This paper presents the results of performance tests conducted on Solar Invictus 53S `system'; an economically effective solar steam generation solution designed and developed by ZED Solar Ltd. The system consists of a dual axis tracking parabolic solar dish and bespoke cavity type receiver, which works as a Once Through Solar Steam Generator `OTSSG' mounted at the focal point of the dish. The overall performance and efficiency of the system depends primarily on the optical efficiency of the solar dish and thermal efficiency of the OTSSG. Optical testing performed include `on sun' tests using CCD camera images and `burn plate' testing to evaluate the sunspot for size and quality. The intercept factor was calculated using a colour look-back method to determine the percentage of solar rays focused into the receiver. Solar dish tracking stability tests were carried out at different times of day to account for varying dish elevation angles and positions, movement of the sunspot centroid was recorded and logged using a CCD camera. Finally the overall performance and net solar to steam efficiency of the system was calculated by experimentally measuring the output steam parameters at varying Direct Normal Insolation (DNI) levels at ZED Solar's test facility in Lahore, Pakistan. Thermal losses from OTSSG were calculated using the known optical efficiency and measured changes in output steam enthalpy.

  11. Quantitative analyses of impurity silicon-carbide (SiC) and high-purity-titanium by neutron activation analyses based on k0-standardization method. Development of irradiation silicon technology in productivity using research reactor (Joint research)

    Motohashi, Jun; Takahashi, Hiroyuki; Magome, Hirokatsu; Sasajima, Fumio; Tokunaga, Okihiro; Kawasaki, Kozo; Onizawa, Koji; Isshiki, Masahiko

    2009-07-01

    JRR-3 and JRR-4 have been providing neutron-transmutation-doped silicon (NTD-Si) by using the silicon NTD process, which is a method to produce a high quality semiconductor. The domestic supply of NTD-Si is insufficient for the demand, and the market of NTD-Si is significantly growing at present. It is very important to increase achieve the production. To fulfill the requirement, we have been investigating a neutron filter, which is made of high-purity-titanium, for uniform doping. Silicon-carbide (SiC) semiconductor doped with NTD technology is considered suitable for high power devices with superior performances to conventional Si-based devices. We are very interested in the SiC as well. This report presents the results obtained after the impurity contents in the high-purity-titanium and SiC were analyzed by neutron activation analyses (NAA) using k 0 -standardization method. There were 6 and 9 impurity elements detected from the high-purity-titanium and SiC, respectively. Among those Sc from the high-purity-titanium and Fe from SiC were comparatively long half life nuclides. From the viewpoint of exposure in handling them, we need to examine the impurity control of materials. (author)

  12. A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines

    Jaffe, Leonard D.

    1988-01-01

    This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  13. A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines

    Jaffe, Leonard D.

    1988-11-01

    This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  14. Detail design of a 10.4-m stretched-membrane dish. Phase 2, Final report

    1994-01-01

    This report describes efforts conducted under Tasks 3 and 4 of the second phase of the project to develop a single-element stretched-membrane dish concept to reduce the cost of a high-performance concentrating solar collector. We completed the detailed design for such a collector suitable to drive a 25-kWe Stirling motor generator. The design includes the collectors, optical element, the drive, and support systems. The aperture of the optical element was sized to provide the required energy to the engine based on test data and analytical models of the concentrator receiver, and engine. The design of the optical element was improved based on experience gained from the design, fabrication, and testing of several prototypes.

  15. Automatic Evaluation of Colonies Growth rate of Yeasts incubated in Petri dishes using Mobile Platform

    Alecsander Pereira Martins

    2015-10-01

    Full Text Available This paper proposes an automatic method based on computer vision implemented in mobile platform capable of monitoring the growth of microbial colonies incubated in Petri dishes. The developed optimized image processing algorithm performs this task without human intervention from images of colonies of the microorganism in different evolution phases. The contribution of this paper is the development of a fast and robust mobile tool to assist bioprocess experts in monitoring the growth of colonies without using the conventional error prone evaluation techniques. The obtained results successfully demonstrated dimensional alterations in colonies in a faster and more precise fashion when compared with the conventional method, with the additional advantage of versatility in producing reliable estimation of the growth rates with higher statistical significance.

  16. Dispersed solar thermal generation employing parabolic dish-electric transport with field modulated generator systems

    Ramakumar, R.; Bahrami, K.

    1981-01-01

    This paper discusses the application of field modulated generator systems (FMGS) to dispersed solar-thermal-electric generation from a parabolic dish field with electric transport. Each solar generation unit is rated at 15 kWe and the power generated by an array of such units is electrically collected for insertion into an existing utility grid. Such an approach appears to be most suitable when the heat engine rotational speeds are high (greater than 6000 r/min) and, in particular, if they are operated in the variable speed mode and if utility-grade a.c. is required for direct insertion into the grid without an intermediate electric energy storage and reconversion system. Predictions of overall efficiencies based on conservative efficiency figures for the FMGS are in the range of 25 per cent and should be encouraging to those involved in the development of cost-effective dispersed solar thermal power systems.

  17. Optical characterization of nonimaging dish concentrator for the application of dense-array concentrator photovoltaic system.

    Tan, Ming-Hui; Chong, Kok-Keong; Wong, Chee-Woon

    2014-01-20

    Optimization of the design of a nonimaging dish concentrator (NIDC) for a dense-array concentrator photovoltaic system is presented. A new algorithm has been developed to determine configuration of facet mirrors in a NIDC. Analytical formulas were derived to analyze the optical performance of a NIDC and then compared with a simulated result obtained from a numerical method. Comprehensive analysis of optical performance via analytical method has been carried out based on facet dimension and focal distance of the concentrator with a total reflective area of 120 m2. The result shows that a facet dimension of 49.8 cm, focal distance of 8 m, and solar concentration ratio of 411.8 suns is the most optimized design for the lowest cost-per-output power, which is US$1.93 per watt.

  18. Modelling resource consumption for laundry and dish treatment in individual households for various consumer segments

    Stamminger, R. [Institute for Agricultural Engineering, Household and Appliance Technology Section, University of Bonn, Nussallee 5, 53115 Bonn (Germany)

    2011-11-15

    Recent research allocates up to 80% of environmental impact in energy and CO2 terms to direct and indirect consumer activities. Various models discussed how this impact can be assigned to specific lifestyles, production and consumption systems, and psychological motives in order to be able to predict and influence these effects. In this work, another approach is followed by showing on the example of laundry and dish washing how well-known factors of the technical status, consumer practices and demographic data allow building up a model to predict the energy and water consumption for these processes. The results show a variation of a factor of 5 between a more sustainable and a more careless behaviour and allow thus to identify levers to influence it. As results can also be easily transformed into monetary values, this may allow influencing the consumer via this channel as he/she can easily understand what may need to be changed.

  19. Thermal modeling of a pressurized air cavity receiver for solar dish Stirling system

    Zou, Chongzhe; Zhang, Yanping; Falcoz, Quentin; Neveu, Pierre; Li, Jianlan; Zhang, Cheng

    2017-06-01

    A solar cavity receiver model for the dish collector system is designed in response to growing demand of renewable energy. In the present research field, no investigations into the geometric parameters of a cavity receiver have been performed. The cylindrical receiver in this study is composed of an enclosed bottom at the back, an aperture at the front, a helical pipe inside the cavity and an insulation layer on the external surface of the cavity. The influence of several critical receiver parameters on the thermal efficiency is analyzed in this paper: cavity inner diameter and cavity length. The thermal model in this paper is solved considering the cavity dimensions as variables. Implementing the model into EES, each parameter influence is separately investigated, and a preliminary optimization method is proposed.

  20. Trends in IT Innovation to Build a Next Generation Bioinformatics Solution to Manage and Analyse Biological Big Data Produced by NGS Technologies

    Alexandre G. de Brevern

    2015-01-01

    Full Text Available Sequencing the human genome began in 1994, and 10 years of work were necessary in order to provide a nearly complete sequence. Nowadays, NGS technologies allow sequencing of a whole human genome in a few days. This deluge of data challenges scientists in many ways, as they are faced with data management issues and analysis and visualization drawbacks due to the limitations of current bioinformatics tools. In this paper, we describe how the NGS Big Data revolution changes the way of managing and analysing data. We present how biologists are confronted with abundance of methods, tools, and data formats. To overcome these problems, focus on Big Data Information Technology innovations from web and business intelligence. We underline the interest of NoSQL databases, which are much more efficient than relational databases. Since Big Data leads to the loss of interactivity with data during analysis due to high processing time, we describe solutions from the Business Intelligence that allow one to regain interactivity whatever the volume of data is. We illustrate this point with a focus on the Amadea platform. Finally, we discuss visualization challenges posed by Big Data and present the latest innovations with JavaScript graphic libraries.

  1. Trends in IT Innovation to Build a Next Generation Bioinformatics Solution to Manage and Analyse Biological Big Data Produced by NGS Technologies

    de Brevern, Alexandre G.; Meyniel, Jean-Philippe; Fairhead, Cécile; Neuvéglise, Cécile; Malpertuy, Alain

    2015-01-01

    Sequencing the human genome began in 1994, and 10 years of work were necessary in order to provide a nearly complete sequence. Nowadays, NGS technologies allow sequencing of a whole human genome in a few days. This deluge of data challenges scientists in many ways, as they are faced with data management issues and analysis and visualization drawbacks due to the limitations of current bioinformatics tools. In this paper, we describe how the NGS Big Data revolution changes the way of managing and analysing data. We present how biologists are confronted with abundance of methods, tools, and data formats. To overcome these problems, focus on Big Data Information Technology innovations from web and business intelligence. We underline the interest of NoSQL databases, which are much more efficient than relational databases. Since Big Data leads to the loss of interactivity with data during analysis due to high processing time, we describe solutions from the Business Intelligence that allow one to regain interactivity whatever the volume of data is. We illustrate this point with a focus on the Amadea platform. Finally, we discuss visualization challenges posed by Big Data and present the latest innovations with JavaScript graphic libraries. PMID:26125026

  2. Trends in IT Innovation to Build a Next Generation Bioinformatics Solution to Manage and Analyse Biological Big Data Produced by NGS Technologies.

    de Brevern, Alexandre G; Meyniel, Jean-Philippe; Fairhead, Cécile; Neuvéglise, Cécile; Malpertuy, Alain

    2015-01-01

    Sequencing the human genome began in 1994, and 10 years of work were necessary in order to provide a nearly complete sequence. Nowadays, NGS technologies allow sequencing of a whole human genome in a few days. This deluge of data challenges scientists in many ways, as they are faced with data management issues and analysis and visualization drawbacks due to the limitations of current bioinformatics tools. In this paper, we describe how the NGS Big Data revolution changes the way of managing and analysing data. We present how biologists are confronted with abundance of methods, tools, and data formats. To overcome these problems, focus on Big Data Information Technology innovations from web and business intelligence. We underline the interest of NoSQL databases, which are much more efficient than relational databases. Since Big Data leads to the loss of interactivity with data during analysis due to high processing time, we describe solutions from the Business Intelligence that allow one to regain interactivity whatever the volume of data is. We illustrate this point with a focus on the Amadea platform. Finally, we discuss visualization challenges posed by Big Data and present the latest innovations with JavaScript graphic libraries.

  3. Flexible Sheet-Type Sensor for Noninvasive Measurement of Cellular Oxygen Metabolism on a Culture Dish.

    Mari Kojima

    Full Text Available A novel flexible sensor was developed for the noninvasive oxygen metabolism measurement of cultivated cells and tissues. This device is composed of a transparent double-layered polymer sheet of ethylene-vinyl alcohol (EVOH and poly(dimethylsiloxane (PDMS having an array of microhole structures of 90 μm diameter and 50 μm depth on its surface. All the microhole structures were equipped with a 1-μm-thick optical chemical sensing layer of platinum porphyrin-fluoropolymer on their bottom. The three-dimensional microstructures of the sensor were fabricated by a newly developed simple and low-cost production method named self-aligned hot embossing. The device was designed to be attached slightly above the cells cultivated on a dish to form a temporarily closed microspace over the target cells during measurement. Since the change in oxygen concentration is relatively fast in the microcompartmentalized culture medium, a rapid evaluation of the oxygen consumption rate is possible by measuring the phosphorescence lifetime of the platinum porphyrin-fluoropolymer. The combined use of the device and an automated optical measurement system enabled the high-throughput sensing of cellular oxygen consumption (100 points/min. We monitored the oxygen metabolism of the human breast cancer cell line MCF7 on a Petri dish and evaluated the oxygen consumption rate to be 0.72 ± 0.12 fmol/min/cell. Furthermore, to demonstrate the utility of the developed sensing system, we demonstrated the mapping of the oxygen consumption rate of rat brain slices and succeeded in visualizing a clear difference among the layer structures of the hippocampus, i.e., the cornu ammonis (CA1 and CA3 and dentate gyrus (DG.

  4. On-sun performance of an improved dish-based HCPV system

    Stalcup, Thomas; Angel, Roger P.; Coughenour, Blake; Wheelwright, Brian; Connors, Tom; Davison, Warren; Lesser, David; Elliott, Justin; Schaefer, John

    2012-10-01

    The University of Arizona has developed a new dish-based High Concentration Photovoltaic (HCPV) system which is in the process of being commercialized by REhnu, Inc. The basic unit uses a paraboloidal glass reflector 3.1 m x 3.1 m square to bring sunlight to a high power point focus at a concentration of ~20,000x. A unique optical system at the focus reformats the concentrated sunlight so as to uniformly illuminate 36 triple junction cells at 1200x geometric concentration1. The relay optics and cells are integrated with an active cooling system in a self-contained Power Conversion Unit (PCU) suspended above the dish reflector. Only electrical connections are made to the PCU as the active cooling system within is completely sealed. Eight of these reflector/PCU units can be mounted on a single two axis tracking structure2. Our 1st generation prototype reflector/PCU unit consistently generated 2.2 kW of power normalized to 1kW/m2 DNI in over 200 hours of on-sun testing in 20113. Here, we present on-sun performance results for our 2nd generation prototype reflector/PCU unit, which has been in operation since June 2012. This improved system consistently generates 2.7 kW of power normalized to 1kW/m2 DNI and has logged over 100 hours of on-sun testing. This system is currently operating at28% DC net system efficiency with an operating cell temperature of only 20°C above ambient. Having proven this system concept, work on our 3rd generation prototype is underway with a focus on manufacturability, lower cost, and DC efficiency target of 32% or better.

  5. Indonesian consumers' perception of tempe in a restaurant setting traditional and modern tempe version in traditional and innovative dishes

    Fibri, Dwi Larasatie Nur; Frøst, Michael Bom

    by introducing local bean tempe in fine dining. The objective of this research was to study how different raw materials, dishes and gastronomic style affect the perception and appreciation of the food. A restaurant experiment (n=208) was carried out. Three different types of tempe (local soybean tempe, imported...

  6. Recipes and nutritional value of dishes prepared from green-leafy vegetables in an urban district of Antananarivo (Madagascar).

    Randrianatoandro, Verohanitra Annie; Avallone, Sylvie; Picq, Christian; Ralison, Charlotte; Trèche, Serge

    2010-06-01

    The recipes of 50 multi-ingredient dishes consumed by the population in an urban district were noted down. The nutritional value was determined as well as the cook value of the dishes in order to evaluate the severity of the thermal treatment. The recipes were simple and involved steps such as boiling, mixing, and cutting. Fibre contents were rather low except when the leaf stems were included. All the dishes had very high beta-carotene content (15.8-25.0 mg/100 g dry matter) and retinol activity equivalent (RAE) (1.3-2.3 mg RAE/100 g dry matter) because of the high proportion of fresh leafy vegetables (from 41.2% to 58.8% of the total dry matter of the ingredients). When meat was added to the preparation, the micronutrient content (iron, zinc, and retinol) was not increased significantly. In three dishes, a positive correlation was found between the thermal treatment severity and the 13-cis-beta-carotene amount.

  7. Isotopic examination of links between diet, social differentiation, and DISH at the post-medieval Carmelite Friary of Aalst, Belgium.

    Quintelier, Kim; Ervynck, Anton; Müldner, Gundula; Van Neer, Wim; Richards, Michael P; Fuller, Benjamin T

    2014-02-01

    Stable isotope ratios (δ(13) C and δ(15) N) were measured in human burials from the post-medieval (16th-18th c. AD) Carmelite friary burial grounds at Aalst, a town in Flanders, Belgium. Dietary patterns of 39 adult individuals were analyzed, from a mixed monastic and lay population buried in three different locations, reflecting groups with differing social status. The data show significant variation in the consumption of perhaps meat, but certainly also marine protein between females and males. This result represents a remarkable continuity with medieval dietary patterns, suggesting that the social and economic changes of the early modern period had a limited effect on everyday life. When both sexes were examined together, individuals buried in the cloister garth consumed significantly less marine protein compared to people buried in the church, likely reflecting social stratification. No statistical differences were observed between isotopic values from the church and the cloister alley, suggesting a similarly diverse diet of the monastic part of the buried population and that of the richer lay population. Finally, the hypothesis that diffuse idiopathic skeletal hyperostosis (DISH) is linked to a diet rich in animal protein was tested. No systematic or statistically significant differences between pathological and non-pathological bones from the same individuals affected with DISH were observed, and no statistical differences were found between individuals with DISH and individuals without DISH. Copyright © 2013 Wiley Periodicals, Inc.

  8. Phytate/calcium molar ratio does not predict accessibility of calcium in ready-to-eat dishes.

    Erba, Daniela; Manini, Federica; Meroni, Erika; Casiraghi, Maria C

    2017-08-01

    Phytic acid (PA), a naturally occurring compound of plant food, is generally considered to affect mineral bioavailability. The aim of this study was to investigate the reliability of the PA/calcium molar ratio as a predictive factor of calcium accessibility in composed dishes and their ingredients. Dishes were chosen whose ingredients were rich in Ca (milk or cheese) or in PA (whole-wheat cereals) in order to consider a range of PA/Ca ratios (from 0 to 2.4) and measure Ca solubility using an in vitro approach. The amounts of soluble Ca in composed dishes were consistent with the sum of soluble Ca from ingredients (three out of five meals) or higher. Among whole-wheat products, bread showed higher Ca accessibility (71%, PA/Ca = 1.1) than biscuits (23%, PA/Ca = 0.9) and pasta (15%, PA/Ca = 1.5), and among Ca-rich ingredients, semi-skimmed milk displayed higher Ca accessibility (64%) than sliced cheese (50%) and Parmesan (38%). No significant correlation between the PA/Ca ratio and Ca accessibility was found (P = 0.077). The reliability of the PA/Ca ratio for predicting the availability of calcium in composed dishes is unsatisfactory; data emphasized the importance of the overall food matrix influence on mineral accessibility. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  9. Risk factors for contamination of ready-to-eat street-vended poultry dishes in Dakar, Senegal.

    Cardinale, E; Perrier Gros-Claude, J D; Tall, F; Guèye, E F; Salvat, G

    2005-08-25

    Our objective was to investigate the Salmonella and Campylobacter contamination of traditional ready-to-eat street-vended poultry dishes and to assess the association of some restaurant characteristics and cooking practices with the contamination of these meals. One hundred and forty-eight street-restaurants were studied from January 2003 to April 2004 in Dakar. A questionnaire was submitted to the managers, and samples of ready-to-eat poultry dishes were taken. Salmonella spp. was isolated in 20.1% of the 148 street-restaurants studied and in 10.1% samples of poultry dishes. The most prevalent serovars isolated were Salmonella hadar, Salmonella enteritidis and Salmonella brancaster. Campylobacter jejuni was detected in only 3 restaurants and 3 poultry dishes. Not peeling and not cleaning vegetables and other ingredients during meal preparation (OR=3.58), dirty clothing for restaurant employees (OR=4.65), reheating previously cooked foods (OR=5.2), and no kitchen and utensils disinfection (OR=3.47) were associated with an increasing risk of Salmonella contamination. Adequate cooking procedures decreased the risk of Salmonella contamination (OR=0.15).

  10. Observing the Sun with the Atacama Large Millimeter/submillimeter Array (ALMA): Fast-Scan Single-Dish Mapping

    White, S. M.; Iwai, K.; Phillips, N. M.; Hills, R. E.; Hirota, A.; Yagoubov, P.; Siringo, G.; Shimojo, M.; Bastian, T. S.; Hales, A. S.; Sawada, T.; Asayama, S.; Sugimoto, M.; Marson, R. G.; Kawasaki, W.; Muller, E.; Nakazato, T.; Sugimoto, K.; Brajša, R.; Skokić, I.; Bárta, M.; Kim, S.; Remijan, A. J.; de Gregorio, I.; Corder, S. A.; Hudson, H. S.; Loukitcheva, M.; Chen, B.; De Pontieu, B.; Fleishmann, G. D.; Gary, D. E.; Kobelski, A.; Wedemeyer, S.; Yan, Y.

    2017-07-01

    The Atacama Large Millimeter/submillimeter Array (ALMA) radio telescope has commenced science observations of the Sun starting in late 2016. Since the Sun is much larger than the field of view of individual ALMA dishes, the ALMA interferometer is unable to measure the background level of solar emission when observing the solar disk. The absolute temperature scale is a critical measurement for much of ALMA solar science, including the understanding of energy transfer through the solar atmosphere, the properties of prominences, and the study of shock heating in the chromosphere. In order to provide an absolute temperature scale, ALMA solar observing will take advantage of the remarkable fast-scanning capabilities of the ALMA 12 m dishes to make single-dish maps of the full Sun. This article reports on the results of an extensive commissioning effort to optimize the mapping procedure, and it describes the nature of the resulting data. Amplitude calibration is discussed in detail: a path that uses the two loads in the ALMA calibration system as well as sky measurements is described and applied to commissioning data. Inspection of a large number of single-dish datasets shows significant variation in the resulting temperatures, and based on the temperature distributions, we derive quiet-Sun values at disk center of 7300 K at λ = 3 mm and 5900 K at λ = 1.3 mm. These values have statistical uncertainties of about 100 K, but systematic uncertainties in the temperature scale that may be significantly larger. Example images are presented from two periods with very different levels of solar activity. At a resolution of about 25'', the 1.3 mm wavelength images show temperatures on the disk that vary over about a 2000 K range. Active regions and plages are among the hotter features, while a large sunspot umbra shows up as a depression, and filament channels are relatively cool. Prominences above the solar limb are a common feature of the single-dish images.

  11. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed

    Sandria Godwin

    2016-06-01

    Full Text Available Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA recommends cooking egg mixtures until the center reaches 71 °C (160 °F. The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes (n = 226 from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89, browned (76, clean toothpick/knife (60, puffed (27, and jiggled (13. Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and “jiggled” This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish.

  12. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed

    Godwin, Sandria; Maughan, Curtis; Chambers, Edgar

    2016-01-01

    Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA) recommends cooking egg mixtures until the center reaches 71 °C (160 °F). The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes (n = 226) from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each) were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89), browned (76), clean toothpick/knife (60), puffed (27), and jiggled (13). Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole) were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and “jiggled” This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish. PMID:28231140

  13. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed.

    Godwin, Sandria; Maughan, Curtis; Chambers, Edgar

    2016-06-23

    Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA) recommends cooking egg mixtures until the center reaches 71 °C (160 °F). The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes ( n = 226) from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each) were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89), browned (76), clean toothpick/knife (60), puffed (27), and jiggled (13). Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole) were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and "jiggled" This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish.

  14. Differences in nutrient and energy content of commonly-consumed dishes prepared in restaurants vs. at home in Hunan province, China

    Jia, Xiaofang; Liu, Jiawu; Chen, Bo; Jin, Donghui; Fu, Zhongxi; Liu, Huilin; Du, Shufa; Popkin, Barry M.; Mendez, Michelle A.

    2017-01-01

    Objective Eating away from home is associated with poor diet quality, in part due to less healthy food choices and larger portions. However, few studies take into account the potential additional contribution of differences in food composition between restaurant- and home-prepared dishes. This study aimed to investigate differences in nutrients of dishes prepared in restaurants vs. at home. Design Eight commonly consumed dishes were collected in 20 of each of the following types of locations: small and large restaurants, and urban and rural households. In addition, two fast-food items were collected from 10 KFC’s, McDonald’s, and food stalls. Five samples per dish were randomly pooled from every location. Nutrients were analyzed and energy was calculated in composite samples. Differences in nutrients of dishes by preparation location were determined. Setting Urban and rural. Subjects Sodium, potassium, protein, total fat, fatty acids, carbohydrate, and energy in dishes. Results On average, both the absolute and relative fat content, saturated fatty acid (SFA) and sodium/potassium ratio were higher in dishes prepared in restaurants than households (Prestaurants (P restaurant preparation was consistently negatively associated with protein and positively associated with the percentage energy from fat in all dishes. Moreover, restaurant preparation also positively influenced the SFA content in dishes, except at the highest quantiles. Conclusions These findings suggest that compared to home preparation, dishes prepared in restaurants in China may differ in concentrations of total fat, SFA, protein, and sodium/potassium ratio, which may further contribute, beyond food choices, to less healthy nutrient intake linked to eating away from home. PMID:29306339

  15. Open-dish incubator for live cell imaging with an inverted microscope.

    Heidemann, Steven R; Lamoureux, Phillip; Ngo, Kha; Reynolds, Matthew; Buxbaum, Robert E

    2003-10-01

    Here we describe the design and fabrication of an inexpensive cell culture incubator for the stage of an inverted light microscope for use in live cell imaging. This device maintains the temperature of the cell culture at 37 degrees C with great stability and, after reaching equilibrium, provides focal stability of an image for 20-25 min with oil-immersion lenses. We describe two versions of the incubator: one for use with standard 60-mm plastic culture dishes, and the other version for imaging of cells on glass coverslips. Either can be made for less than $400. Most components are widely available commercially, and it requires only simple wiring and 3 h to assemble. Although the device is generally useful for live cell imaging on an inverted microscope, it is particularly suitable for work in which instruments are introduced into the culture, such as electrophysiology or micromanipulation. The design is based on the principle that control performance is limited by the lag time between detection and response. The key element of the design is a heated, temperature-controlled aluminum ring serving as a mini-incubator surrounding the culture vessel. For this reason, we call our design a "ringcubator."

  16. Software used with the flux mapper at the solar parabolic dish test site

    Miyazono, C.

    1984-01-01

    Software for data archiving and data display was developed for use on a Digital Equipment Corporation (DEC) PDP-11/34A minicomputer for use with the JPL-designed flux mapper. The flux mapper is a two-dimensional, high radiant energy scanning device designed to measure radiant flux energies expected at the focal point of solar parabolic dish concentrators. Interfacing to the DEC equipment was accomplished by standard RS-232C serial lines. The design of the software was dicated by design constraints of the flux-mapper controller. Early attemps at data acquisition from the flux-mapper controller were not without difficulty. Time and personnel limitations result in an alternative method of data recording at the test site with subsequent analysis accomplished at a data evaluation location at some later time. Software for plotting was also written to better visualize the flux patterns. Recommendations for future alternative development are discussed. A listing of the programs used in the anaysis is included in an appendix.

  17. A PDMS Device Coupled with Culture Dish for In Vitro Cell Migration Assay.

    Lv, Xiaoqing; Geng, Zhaoxin; Fan, Zhiyuan; Wang, Shicai; Pei, WeiHua; Chen, Hongda

    2018-04-30

    Cell migration and invasion are important factors during tumor progression and metastasis. Wound-healing assay and the Boyden chamber assay are efficient tools to investigate tumor development because both of them could be applied to measure cell migration rate. Therefore, a simple and integrated polydimethylsiloxane (PDMS) device was developed for cell migration assay, which could perform quantitative evaluation of cell migration behaviors, especially for the wound-healing assay. The integrated device was composed of three units, which included cell culture dish, PDMS chamber, and wound generation mold. The PDMS chamber was integrated with cell culture chamber and could perform six experiments under different conditions of stimuli simultaneously. To verify the function of this device, it was utilized to explore the tumor cell migration behaviors under different concentrations of fetal bovine serum (FBS) and transforming growth factor (TGF-β) at different time points. This device has the unique capability to create the "wound" area in parallel during cell migration assay and provides a simple and efficient platform for investigating cell migration assay in biomedical application.

  18. Metabolic Profiling Directly from the Petri Dish Using Nanospray Desorption Electrospray Ionization Imaging Mass Spectrometry

    Watrous, Jeramie D.; Roach, Patrick J.; Heath, Brandi S.; Alexandrov, Theodore; Laskin, Julia; Dorrestein, Pieter C.

    2013-11-05

    Understanding molecular interaction pathways in complex biological systems constitutes a treasure trove of knowledge that might facilitate the specific, chemical manipulation of the countless microbiological systems that occur throughout our world. However, there is a lack of methodologies that allow the direct investigation of chemical gradients and interactions in living biological systems, in real time. Here, we report the use of nanospray desorption electrospray ionization (nanoDESI) imaging mass spectrometry for in vivo metabolic profiling of living bacterial colonies directly from the Petri dish with absolutely no sample preparation needed. Using this technique, we investigated single colonies of Shewanella oneidensis MR-1, Bacillus subtilis 3610, and Streptomyces coelicolor A3(2) as well as a mixed biofilm of S. oneidensis MR-1 and B. subtilis 3610. Data from B. subtilis 3610 and S. coelicolor A3(2) provided a means of validation for the method while data from S. oneidensis MR-1 and the mixed biofilm showed a wide range of compounds that this bacterium uses for the dissimilatory reduction of extracellular metal oxides, including riboflavin, iron-bound heme and heme biosynthetic intermediates, and the siderophore putrebactin.

  19. Performance and cost of energy transport and storage systems for dish applications using reversible chemical reactions

    Schredder, J. M.; Fujita, T.

    1984-01-01

    The use of reversible chemical reactions for energy transport and storage for parabolic dish networks is considered. Performance and cost characteristics are estimated for systems using three reactions (sulfur-trioxide decomposition, steam reforming of methane, and carbon-dioxide reforming of methane). Systems are considered with and without storage, and in several energy-delivery configurations that give different profiles of energy delivered versus temperature. Cost estimates are derived assuming the use of metal components and of advanced ceramics. (The latter reduces the costs by three- to five-fold). The process that led to the selection of the three reactions is described, and the effects of varying temperatures, pressures, and heat exchanger sizes are addressed. A state-of-the-art survey was performed as part of this study. As a result of this survey, it appears that formidable technical risks exist for any attempt to implement the systems analyzed in this study, especially in the area of reactor design and performance. The behavior of all components and complete systems under thermal energy transients is very poorly understood. This study indicates that thermochemical storage systems that store reactants as liquids have efficiencies below 60%, which is in agreement with the findings of earlier investigators.

  20. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study.

    Ducrot, Pauline; Fassier, Philippine; Méjean, Caroline; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2016-07-05

    Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity) was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., "nutritional balance of the dish"), constraints (e.g., "my cooking skills"), pleasure (e.g., "originality of the dish"), specific diets (e.g., "my health status"), and organization (e.g., "what I planned to eat"). A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval): 0.62-0.67)), whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10-1.19)) and specific diets (OR = 1.19 (95% CI: 1.17-1.22)). No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  1. Motives for dish choices during home meal preparation: results from a large sample of the NutriNet-Santé study.

    Ducrot, Pauline; Méjean, Caroline; Allès, Benjamin; Fassier, Philippine; Hercberg, Serge; Péneau, Sandrine

    2015-09-30

    Although culinary practices have strongly evolved over time, few data are available on contemporary dish choices during meal preparation. We therefore sought to determine individual motives when choosing dishes to be prepared during weekdays and on weekends. The importance of 27 criteria related to dish choices was assessed in 53,025 participants in the NutriNet-Santé study. Dimensions of dish choice motives were investigated using exploratory factor analysis. Mean ratings of motives during weekdays and on weekends were compared using Student's t-test. Association between socio-demographic and cooking practice characteristics, and dish choice motives were evaluated using logistic regression models. Five dimensions of dish choice motives emerged: healthy diet (explained variance: 48.3%), constraints (19.0%), pleasure (12.1%), specific diets (11.0%) and organization (9.6%). The healthy diet factor was the most important on weekdays (mean rating 3.93) and weekends (3.90). Pleasure (3.61) had a higher score than constraints (3.54) on weekends (p < 0.0001) while the opposite was observed on weekdays (3.42 vs 3.77, respectively) (p < 0.0001). Organization was more important on weekdays (2.89) than on weekends (2.75) (p < 0.0001). Dish choice motives appeared to be significantly associated with socio-demographic and cooking practice characteristics. This study highlighted factors involved in dish choices in meal preparation on weekdays and weekends, as well as individual characteristics which determine motives for dish choices. From a public health perspective, these findings might help to develop appropriate strategies for promoting home meal preparation.

  2. Thermo-economic multi-objective optimization of solar dish-Stirling engine by implementing evolutionary algorithm

    Ahmadi, Mohammad H.; Sayyaadi, Hoseyn; Mohammadi, Amir H.; Barranco-Jimenez, Marco A.

    2013-01-01

    Highlights: • Thermo-economic multi-objective optimization of solar dish-Stirling engine is studied. • Application of the evolutionary algorithm is investigated. • Error analysis is done to find out the error through investigation. - Abstract: In the recent years, remarkable attention is drawn to Stirling engine due to noticeable advantages, for instance a lot of resources such as biomass, fossil fuels and solar energy can be applied as heat source. Great number of studies are conducted on Stirling engine and finite time thermo-economic is one of them. In the present study, the dimensionless thermo-economic objective function, thermal efficiency and dimensionless power output are optimized for a dish-Stirling system using finite time thermo-economic analysis and NSGA-II algorithm. Optimized answers are chosen from the results using three decision-making methods. Error analysis is done to find out the error through investigation

  3. Mouthwatering but erosive? A preliminary assessment of the acidity of a basic sauce used in many Indian dishes.

    Ghai, Nandini; Burke, F J Trevor

    2012-12-01

    The aim of this study was to assess whether some types of Indian cuisine may contain erosive components. Indian dishes were prepared by a previously published method and their pH measured using a pH probe. The results indicated: (i) that some components of Indian cooking, such as tomatoes and red chilli powder, had the potential to erode enamel; (ii) that the pH of some foods was reduced with increasing temperature; and (iii) that all the basic masalas made and tested had a pH of less than 4.5. Within the limitations of the study, it may be concluded that the basic sauce/masala used in north Indian dishes may have erosive potential. This information could be considered useful when advising patients who eat Indian curries about causes of acid erosion of their teeth.

  4. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong; Say, Yee-How

    2012-01-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respect...

  5. Dish/Stirling Hybrid-Receiver Sub-Scale Tests and Full-Scale Design

    Andraka, Charles; Bohn, Mark S.; Corey, John; Mehos, Mark; Moreno, James; Rawlinson, Scott

    1999-01-01

    We have designed and tested a prototype dish/Stirling hybrid-receiver combustion system. The system consists of a pre-mixed natural-gas burner heating a pin-finned sodium heat pipe. The design emphasizes simplicity, low cost, and ruggedness. Our test was on a 1/6 th -scale device, with a nominal firing rate of 18kWt, a power throughput of 13kWt, and a sodium vapor temperature of 750 ampersand deg;C. The air/fuel mixture was electrically preheated to 640 ampersand deg;C to simulate recuperation. The test rig was instrumented for temperatures, pressures, flow rates, overall leak rate, and exhaust emissions. The data verify our burner and heat-transfer models. Performance and post-test examinations validate our choice of materials and fabrication methods. Based on the 1/6 th -scale results, we are designing a till-scale hybrid receiver. This is a fully-integrated system, including burner, pin-fin primary heat exchanger, recuperator (in place of the electrical pre-heater used in the prototype system), solar absorber, and sodium heat pipe. The major challenges of the design are to avoid pre-ignition, achieve robust heat-pipe performance, and attain long life of the burner matrix, recuperator, and flue-gas seals. We have used computational fluid dynamics extensively in designing to avoid pre-ignition and for designing the heat-pipe wick, and we have used individual component tests and results of the 1/6 th -scale test to optimize for long life. In this paper, we present our design philosophy and basic details of our design. We describe the sub-scale test rig and compare test results with predictions. Finally, we outline the evolution of our full-scale design, and present its current status

  6. Analyse that

    Smith, Maurice

    2011-06-15

    The oil industry is starting to implement new technologies such as horizontal drilling and multistage fracking to light oil production. Most of the producers are copying what is done by their coounterparts. Experts say that another approach should be taken because you can get quicker results with a technical analysis using an analytical model than by drilling a lot of wells. In general, producers are also eager to put too many fracs into the ground to inflate initial production rates but this does not increase the cumulative recovery so they are spending more money to end up with the same result. The oil industry still has to work to find a way to optimize production and reservoir management and costs.

  7. Spatially Extended and High-Velocity Dispersion Molecular Component in Spiral Galaxies: Single-Dish Versus Interferometric Observations

    Caldú-Primo, Anahi; Schruba, Andreas; Walter, Fabian; Leroy, Adam; Bolatto, Alberto D.; Vogel, Stuart

    2015-02-01

    Recent studies of the molecular medium in nearby galaxies have provided mounting evidence that the molecular gas can exist in two phases: one that is clumpy and organized as molecular clouds and another one that is more diffuse. This last component has a higher velocity dispersion than the clumpy one. In order to investigate these two molecular components further, we compare the fluxes and line widths of CO in NGC 4736 and NGC 5055, two nearby spiral galaxies for which high-quality interferometric as well as single-dish data sets are available. Our analysis leads to two main results: (1) employing three different methods, we determine the flux recovery of the interferometer as compared to the single-dish to be within a range of 35%-74% for NGC 4736 and 81%-92% for NGC 5055, and (2) when focusing on high (S/N ≥ 5) lines of sight (LOSs), the single-dish line widths are larger by ˜(40 ± 20)% than the ones derived from interferometric data, which is in agreement with stacking all LOSs. These results point to a molecular gas component that is distributed over spatial scales larger than 30″(˜1 kpc), and is therefore filtered out by the interferometer. The available observations do not allow us to distinguish between a truly diffuse gas morphology and a uniform distribution of small clouds that are separated by less than the synthesized beam size (˜3″ or ˜100 pc), as they would both be invisible for the interferometer. This high velocity dispersion component has a dispersion similar to what is found in the atomic medium, as traced through observations of the H i line.

  8. Spatially extended and high-velocity dispersion molecular component in spiral galaxies: Single-dish versus interferometric observations

    Caldú-Primo, Anahi; Walter, Fabian; Schruba, Andreas; Leroy, Adam; Bolatto, Alberto D.; Vogel, Stuart

    2015-01-01

    Recent studies of the molecular medium in nearby galaxies have provided mounting evidence that the molecular gas can exist in two phases: one that is clumpy and organized as molecular clouds and another one that is more diffuse. This last component has a higher velocity dispersion than the clumpy one. In order to investigate these two molecular components further, we compare the fluxes and line widths of CO in NGC 4736 and NGC 5055, two nearby spiral galaxies for which high-quality interferometric as well as single-dish data sets are available. Our analysis leads to two main results: (1) employing three different methods, we determine the flux recovery of the interferometer as compared to the single-dish to be within a range of 35%–74% for NGC 4736 and 81%–92% for NGC 5055, and (2) when focusing on high (S/N ≥ 5) lines of sight (LOSs), the single-dish line widths are larger by ∼(40 ± 20)% than the ones derived from interferometric data, which is in agreement with stacking all LOSs. These results point to a molecular gas component that is distributed over spatial scales larger than 30″(∼1 kpc), and is therefore filtered out by the interferometer. The available observations do not allow us to distinguish between a truly diffuse gas morphology and a uniform distribution of small clouds that are separated by less than the synthesized beam size (∼3″ or ∼100 pc), as they would both be invisible for the interferometer. This high velocity dispersion component has a dispersion similar to what is found in the atomic medium, as traced through observations of the H i line.

  9. 48{sup th} Annual meeting on nuclear technology (AMNT 2017). Key topic / Enhanced safety and operation excellence. Focus session: Uncertainty analyses in reactor core simulations

    Zwermann, Winfried [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Garching (Germany). Forschungszentrum

    2017-12-15

    The supplementation of reactor simulations by uncertainty analyses is becoming increasingly important internationally due to the fact that the reliability of simulation calculations can be significantly increased by the quantification of uncertainties in comparison to the use of so-called conservative methods (BEPU- ''Best-Estimate plus Uncertainties''). While systematic uncertainty analyses for thermo-hydraulic calculations have been performed routinely for a long time, methods for taking into account uncertainties in nuclear data, which are the basis for neutron transport calculations, are under development. The Focus Session Uncertainty Analyses in Reactor Core Simulations was intended to provide an overview of international research and development with respect to supplementing reactor core simulations with uncertainty and sensitivity analyses, in research institutes as well as within the nuclear industry. The presented analyses not only focused on light water reactors, but also on advanced reactor systems. Particular emphasis was put on international benchmarks in the field. The session was chaired by Winfried Zwermann (Gesellschaft fuer Anlagen- und Reaktorsicherheit).

  10. Vegetables and Mixed Dishes Are Top Contributors to Phylloquinone Intake in US Adults: Data from the 2011-2012 NHANES.

    Harshman, Stephanie G; Finnan, Emily G; Barger, Kathryn J; Bailey, Regan L; Haytowitz, David B; Gilhooly, Cheryl H; Booth, Sarah L

    2017-07-01

    Background: Phylloquinone is the most abundant form of vitamin K in US diets. Green vegetables are considered the predominant dietary source of phylloquinone. As our food supply diversifies and expands, the food groups that contribute to phylloquinone intake are also changing, which may change absolute intakes. Thus, it is important to identify the contributors to dietary vitamin K estimates to guide recommendations on intakes and food sources. Objective: The purpose of this study was to estimate 1 ) the amount of phylloquinone consumed in the diet of US adults, 2 ) to estimate the contribution of different food groups to phylloquinone intake in individuals with a high or low vegetable intake (≥2 or vegetables/d), and 3 ) to characterize the contribution of different mixed dishes to phylloquinone intake. Methods: Usual phylloquinone intake was determined from NHANES 2011-2012 (≥20 y old; 2092 men and 2214 women) and the National Cancer Institute Method by utilizing a complex, stratified, multistage probability-cluster sampling design. Results: On average, 43.0% of men and 62.5% of women met the adequate intake (120 and 90 μg/d, respectively) for phylloquinone, with the lowest self-reported intakes noted among men, especially in the older age groups (51-70 and ≥71 y). Vegetables were the highest contributor to phylloquinone intake, contributing 60.0% in the high-vegetable-intake group and 36.1% in the low-vegetable-intake group. Mixed dishes were the second-highest contributor to phylloquinone intake, contributing 16.0% in the high-vegetable-intake group and 28.0% in the low-vegetable-intake group. Conclusion: Self-reported phylloquinone intakes from updated food composition data applied to NHANES 2011-2012 reveal that fewer men than women are meeting the current adequate intake. Application of current food composition data confirms that vegetables continue to be the primary dietary source of phylloquinone in the US diet. However, mixed dishes and convenience

  11. Technology.

    Online-Offline, 1998

    1998-01-01

    Focuses on technology, on advances in such areas as aeronautics, electronics, physics, the space sciences, as well as computers and the attendant progress in medicine, robotics, and artificial intelligence. Describes educational resources for elementary and middle school students, including Web sites, CD-ROMs and software, videotapes, books,…

  12. Special report for UNDP on regional RCA project for Asia and the Pacific on industrial applications of isotopes and radiation technology. Technical, economic and commercial analyses

    1980-01-01

    The report contains seven sub-projects for RCA countries on the following problems: tracer technology in industry; non-destructive testing practice; radiation processing; nucleonic control systems for paper manufacture and steel manufacture; mineral exploration, mining and process control; nuclear instruments maintenance practices

  13. Distance distribution of bystander effects in alpha-particle irradiated cell populations using a CR-39-based culture dish

    Gaillard, S.; Pusset, D.; Toledo, S.M. de; Azzam, E.I.; Fromm, M.

    2008-01-01

    Propagation of induced biological effects from irradiated to non-irradiated cells is known to occur in cell cultures exposed to low fluences of charged particles. These bystander effects are currently investigated using microbeam or non-microbeam (broad beams) irradiation techniques. Identification of the targeted and non-targeted bystander cells is critical to our understanding of mechanisms underlying such effects. We developed a novel cell culture dish where the base consists of a thin CR-39 sheet grafted on a thin polyethylene terephthalate (PET) foil. The validity of this device in identifying not only irradiated cells, but also the cellular compartment traversed by the particle track is described. We have optimized track etch parameters that do not interfere with measurement of induced biological endpoints under normal incident irradiation. Thus the culture dishes can be used to determine distance distributions for the propagation of induced biological effects from a hit cell to bystander cells. We describe the computer code developed to determine the distance distributions of propagated biological stress responses in normal human fibroblast cells exposed to very low fluences of alpha particles

  14. Technology

    Xu Jing

    2016-01-01

    Full Text Available The traditional answer card reading method using OMR (Optical Mark Reader, most commonly, OMR special card special use, less versatile, high cost, aiming at the existing problems proposed a method based on pattern recognition of the answer card identification method. Using the method based on Line Segment Detector to detect the tilt of the image, the existence of tilt image rotation correction, and eventually achieve positioning and detection of answers to the answer sheet .Pattern recognition technology for automatic reading, high accuracy, detect faster

  15. Application of the monazite radiation source to the petri dish-type cloud chamber and the influence of several factors on occurrence of tracks

    Hayakawa, Issei; Sago, Yutaka; Mori, Chizuo

    2012-01-01

    Monazite radiation source (2.5 mmΦ) proved to be useful as a radiation source of cloud chamber without the dispersion of powder or its adhesion because of a sintered body. After the track appeared within one minute after having put the petri dish on the dry ice, the number increased rapidly followed by the tendency to decrease gradually after that. The tracks can be observed for about 20 minutes after cooled with dry ice. The size of dry ice should be chosen to enter the inside of the bottom edge of the petri dish. The same number of tracks as using conventional mantle radiation source was obtained by utilizing 3 pieces of monazite sintered body separated mutually by about 7.5 mm. Hence the petri dish-type cloud chamber with the monazite sintered body as radiation source revealed to make the observation of track easy and prompt. (author)

  16. In vivo cardiac nano-imaging: A new technology for high-precision analyses of sarcomere dynamics in the heart.

    Shimozawa, Togo; Hirokawa, Erisa; Kobirumaki-Shimozawa, Fuyu; Oyama, Kotaro; Shintani, Seine A; Terui, Takako; Kushida, Yasuharu; Tsukamoto, Seiichi; Fujii, Teruyuki; Ishiwata, Shin'ichi; Fukuda, Norio

    2017-03-01

    The cardiac pump function is a result of a rise in intracellular Ca 2+ and the ensuing sarcomeric contractions [i.e., excitation-contraction (EC) coupling] in myocytes in various locations of the heart. In order to elucidate the heart's mechanical properties under various settings, cardiac imaging is widely performed in today's clinical as well as experimental cardiology by using echocardiogram, magnetic resonance imaging and computed tomography. However, because these common techniques detect local myocardial movements at a spatial resolution of ∼100 μm, our knowledge on the sub-cellular mechanisms of the physiology and pathophysiology of the heart in vivo is limited. This is because (1) EC coupling occurs in the μm partition in a myocyte and (2) cardiac sarcomeres generate active force upon a length change of ∼100 nm on a beat-to-beat basis. Recent advances in optical technologies have enabled measurements of intracellular Ca 2+ dynamics and sarcomere length displacements at high spatial and temporal resolution in the beating heart of living rodents. Future studies with these technologies are warranted to open a new era in cardiac research. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Sizing a solar dish Stirling micro-CHP system for residential application in diverse climatic conditions based on 3E analysis

    Moghadam, Ramin Shabanpour; Sayyaadi, Hoseyn; Hosseinzade, Hadi

    2013-01-01

    Highlights: • 3E analysis was performed on solar CHP systems. • Significant primary energy saving and greenhouse gas reduction were obtained. • The engine was sized so that it had the best economic sound. • Various criteria at different weathers were used for sizing the engine. - Abstract: A solar dish Stirling cogeneration system is considered to provide energy demands of a residential building. As energy demands of the building and output power of the engine are functions of weather condition and solar irradiation flux, the benchmark building was considered to be located in five different cities in Iran with diverse climatic and solar irradiation conditions. The proposed solar dish Stirling micro-CHP system was analyzed based on 3E analysis. The 3E analysis evaluated primary energy saving analysis (energy analysis), carbon dioxide emission reduction (environmental analysis) and payback period for return of investment (economic analysis) and was compared to a reference building that utilized primary energy carriers for its demands. Three scenarios were considered for assessment and sizing the solar dish Stirling engine. In the first scenario, size of the solar dish Stirling engine was selected based on the lowest annual electric power demand while, in second, the highest annual electric power consumption was considered to specify size of the engine. In the third scenario, a solar dish Stirling engine with constant output capacity was considered for the five locations. It was shown that implementing the solar dish Stirling micro-CHP system had good potential in primary energy saving and carbon dioxide emission reduction in all scenarios and acceptable payback period for return of the investment in some scenarios. Finally, the best scenario for selecting size of the engine in each city was introduced using the TOPSIS decision making method. It was demonstrated that, for dry weather, the first scenario was the best while, for hot and humid cities and

  18. Fuel pin transient behavior technology applied to safety analyses. Presentation to AEC Regulatory Staff 4th Regulatory Briefing on safety technology, Washington, D.C., November 19--20, 1974

    1974-11-01

    Information is presented concerning LMFBR fuel pin performance requirements and evaluation; fuels behavior codes with safety interfaces; performance evaluations; ex-reactor materials and simulation tests; models for fuel pin failure; and summary of continuing fuels technology tasks. (DCC)

  19. Translation of Human iPSCs: From Clinical Trial in a Dish to Precision Medicine

    Sayed, Nazish; Liu, Chun; Wu, Joseph C.

    2016-01-01

    The prospect of changing the plasticity of terminally differentiated cells toward pluripotency has completely altered the outlook of biomedical research. Human induced pluripotent stem cells (iPSCs) provide a new source of therapeutic cells free from the ethical issues or immune barriers of human embryonic stem cells. iPSCs also confer considerable advantages over conventional methods of studying human diseases. Since its advent, iPSC technology has expanded, with 3 major applications: disease modeling; regenerative therapy; and drug discovery. Here we discuss, in a comprehensive manner, the recent advances in iPSC technology in relation to basic, clinical, and population health. PMID:27151349

  20. Association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" (Staple food, main dish, and side dish) and intake of nutrients and food groups among Japanese young adults aged 18-24 years: a cross-sectional study.

    Kakutani, Yuya; Kamiya, Saori; Omi, Naomi

    2015-01-01

    "Shushoku," "Shusai," and "Hukusai" are staple food, main dish, and side dish, respectively. The recommended meal in Japan is a combination of "Shushoku," "Shusai," and "Hukusai"; however, it remains unclear whether there is an association between the frequency of these meals and intake of nutrients and food groups. This cross-sectional study examined the association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" and intake of nutrients and food groups among 664 Japanese young adults aged 18-24 y. The dietary habits of the subjects during the preceding month were assessed using a validated brief-type self-administered diet history questionnaire. The frequency of meals combining "Shushoku, Shusai, and Hukusai" was self-reported according to four categories: "less than 1 d or 1 d/wk," "2 or 3 d/wk," "4 or 5 d/wk," and "every day." In both women and men, there was an association between the higher frequency of these meals and higher intake of the following food groups: pulses, green and yellow vegetables, other vegetables, mushrooms, seaweeds, fish and shellfish, and eggs. Moreover, there was an association with higher intake of protein, polyunsaturated fat, n-6 and n-3 polyunsaturated fat, total dietary fiber, soluble and insoluble dietary fiber, β-carotene, α-tocopherol, vitamin K, thiamin, riboflavin, folate, pantothenic acid, vitamin C, potassium, calcium, magnesium, iron, and copper, and lower intake of carbohydrate in both women and men. Our findings support the hypothesis that the meals combining "Shushoku, Shusai, and Hukusai" may be associated with intake of many food groups and nutrients among Japanese young adults.

  1. Child and parent perspectives on healthier side dishes and beverages in restaurant kids' meals: results from a national survey in the United States.

    Shonkoff, Eleanor T; Anzman-Frasca, Stephanie; Lynskey, Vanessa M; Chan, Grace; Glenn, Meaghan E; Economos, Christina D

    2017-07-25

    Children frequently consume foods from restaurants; considering the quick-service sector alone, 1/3 of children eat food from these restaurants on a given day, and among these consumers, 1/3 of their daily calories come from fast food. Restaurant foods and beverages are second only to grocery store foods and beverages in their contribution to total energy intake of U.S. 4- to 11-year-olds. Shifting their restaurant consumption in healthier directions could have a positive impact on child health. In 2014 this study examined self-reported child receptivity and parent awareness of child receptivity to ordering a fruit or vegetable side dish instead of French fries; and milk, water, or flavored water instead of soda/pop with a kids' meal when eating out. Child receptivity to side dishes was compared between 2010 and 2014. An online survey was administered by Nielsen via their Harris Poll Online to a national panel of 711 parents and their 8- to 12-year-old child, as part of a larger study. Frequencies, logistic regressions, t-tests, chi-square tests, and percent agreement were used to evaluate child likelihood of ordering certain side dishes; receptivity to healthier side dish and beverage alternatives; changes in receptivity to healthier sides across years; and parent awareness. A majority of children said they were likely to order a meal with a vegetable (60%), fruit (78%), or French fry (93%) side dish. They were receptive to receiving a fruit or vegetable (FV) side dish instead of French fries (68%); or milk, water, or flavored water instead of soda (81%) with their restaurant kids' meal. Liking/taste was the most common reason for children's feelings. Child receptivity to a FV side dish instead of French fries was high in both years and significantly higher in 2014 (t = -2.12, p = 0.034). The majority of parent and child reports of child receptivity were concordant (85%). These national survey results indicate that children are receptive to FV side dishes and

  2. Assessing intake of spices by pattern of spice use, frequency of consumption and portion size of spices consumed from routinely prepared dishes in southern India.

    Siruguri, Vasanthi; Bhat, Ramesh V

    2015-01-11

    Measurement of dietary intake of spices is gaining significance because of recognition of their health promoting benefits as well as its use for risk assessment of contaminant exposures. Estimating intake of spices at the individual level, presents several challenges since various spices are used as an integrated part of a prepared food and consumed in amounts much smaller than other dietary components. The objective of the present study is to assess intake of spices at the household and individual level on the basis of pattern of spice use and portion size of spice consumed from routinely prepared dishes in Hyderabad city in Southern India. The study was conducted in 100 households in urban areas of Hyderabad city in India with the help of a spice intake questionnaire that was prepared to collect information on the pattern of spice use, frequency, and quantity of spice consumption of 17 spices routinely used in Indian cuisine. The quantity of spice intake was assessed by measuring portion size of spice consumed from the quantity of i) spices added in routinely prepared dishes and ii) the prepared dish consumed by an individual. Based on the type of dish prepared and frequency of preparing the dishes, 11 out of 17 spices were found to be consumed by more than 50% of the households. Maximum number of spices was consumed at weekly frequencies. Red chillies and turmeric were the most frequently consumed spices by 100% of the households. The mean total intake of spices was observed to be higher through dishes consumed daily (10.4 g/portion) than from those consumed at weekly or monthly frequencies. Highest portion size intake was observed for chillies (mean 3.0 g; range 0.05-20.2 g) and lowest for nutmeg (mean 0.14 g; range 0.02-0.64 g) and mace (mean 0.21 g; range: 0.02-0.6 g). The study suggested that assessment of intake of spices varies with frequency of use of spices and type of dish consumed. Portion size estimations of spices consumed and the frequency of

  3. Child and parent perspectives on healthier side dishes and beverages in restaurant kids’ meals: results from a national survey in the United States

    Eleanor T. Shonkoff

    2017-07-01

    Full Text Available Abstract Background Children frequently consume foods from restaurants; considering the quick-service sector alone, 1/3 of children eat food from these restaurants on a given day, and among these consumers, 1/3 of their daily calories come from fast food. Restaurant foods and beverages are second only to grocery store foods and beverages in their contribution to total energy intake of U.S. 4- to 11-year-olds. Shifting their restaurant consumption in healthier directions could have a positive impact on child health. In 2014 this study examined self-reported child receptivity and parent awareness of child receptivity to ordering a fruit or vegetable side dish instead of French fries; and milk, water, or flavored water instead of soda/pop with a kids’ meal when eating out. Child receptivity to side dishes was compared between 2010 and 2014. Methods An online survey was administered by Nielsen via their Harris Poll Online to a national panel of 711 parents and their 8- to 12-year-old child, as part of a larger study. Frequencies, logistic regressions, t-tests, chi-square tests, and percent agreement were used to evaluate child likelihood of ordering certain side dishes; receptivity to healthier side dish and beverage alternatives; changes in receptivity to healthier sides across years; and parent awareness. Results A majority of children said they were likely to order a meal with a vegetable (60%, fruit (78%, or French fry (93% side dish. They were receptive to receiving a fruit or vegetable (FV side dish instead of French fries (68%; or milk, water, or flavored water instead of soda (81% with their restaurant kids’ meal. Liking/taste was the most common reason for children’s feelings. Child receptivity to a FV side dish instead of French fries was high in both years and significantly higher in 2014 (t = −2.12, p = 0.034. The majority of parent and child reports of child receptivity were concordant (85%. Conclusions These national survey

  4. The Flexitarian Flip™ : Testing the Modalities of Flavor as Sensory Strategies to Accomplish the Shift from Meat-Centered to Vegetable-Forward Mixed Dishes.

    Spencer, Molly; Guinard, Jean-Xavier

    2018-01-01

    The American diet is lacking in plant-based foods and vegetables, higher in protein than necessary, and too centered on meat and poultry. Two major dietary shifts recommended by the 2015-2020 U.S. Dietary Guidelines are to increase vegetable intake and to increase the variety of protein food sources. One suggested strategy for doing this is to partially replace meat and poultry with vegetables and plant-based ingredients in mixed dishes. This research tested the potential of flavor modalities (taste, aroma, trigeminal, and their combination) as strategies to increase the sensory appeal of plant-forward dishes. Consumer testing (n = 141) was conducted in a cross-sectional design in a laboratory setting on 24 recipe variations. Three factors were tested: cuisine (Latin American, Mediterranean, and Asian), meat proportion (high-meat/low-vegetable versus low-meat/high-vegetable), and flavor strategy (taste, aroma, trigeminal, and a reduced-intensity trimodal combination). Statistical analysis was performed in R and XLSTAT-Sensory ® 2017. Four consumer preference segments were uncovered. The low-meat dishes achieved parity or higher in consumer acceptance across all recipes and flavor strategies. The taste and trigeminal strategies both had higher overall acceptability scores than the aroma strategy, and the differences were significant (P meat with vegetables in mixed dishes. The trigeminal and trimodal combination strategies were found to be the most promising flavor modalities to use to implement this shift. There is little knowledge of American consumer preferences regarding vegetables in mixed dishes. Mixed dishes are a strategy recommended by the U.S. Dietary Guidelines to increase vegetable consumption and variety of protein sources. This research explores various flavor and culinary strategies with which to carry out the mixed dish meat-vegetable swap and to test the potential of the Flexitarian Flip ™ (the shift from meat-centric to plant-centric diets

  5. FINEDAN - an explicit finite-element calculation code for two-dimensional analyses of fast dynamic transients in nuclear reactor technology

    Adamik, V.; Matejovic, P.

    1989-01-01

    The problems are discussed of nonstationary, nonlinear dynamics of the continuum. A survey is presented of calculation methods in the given area with emphasis on the area of impact problems. A description is presented of the explicit finite elements method and its application to two-dimensional Cartesian and cylindrical configurations. Using the method the explicit calculation code FINEDAN was written which was tested in a series of verification calculations for different configurations and different types of continuum. The main characteristics are presented of the code and of some, of its practical applications. Envisaged trends of the development of the code and its possible applications in the technology of nuclear reactors are given. (author). 9 figs., 4 tabs., 10 refs

  6. Book Review: It's Not You, It's the Dishes: How to Minimize Conflict and Maximize Happiness in Your Relationship

    Derek Lawson

    2014-08-01

    Full Text Available It’s Not You, It’s The Dishes brings economic principles and theory into the married life of couples. The authors simplify economics by providing fundamental concepts while removing technical jargon in a funny, yet intuitive way. Readers are introduced to the basics of comparative advantage, game theory, and eight other economic principles, all while learning lessons on how to resourcefully allocate their limited units of time, money, and energy to yield a better return on their biggest investment of their lives, their marriage. At its core, this is a self-help book aimed at married couples. Nevertheless, financial professionals and academics may benefit from reading the book, particularly because it may be beneficial helping to brainstorm potential solutions with their clients or as “homework” for client couples.

  7. Directed midbrain and spinal cord neurogenesis from pluripotent stem cells to model development and disease in a dish.

    Allodi, Ilary; Hedlund, Eva

    2014-01-01

    Induction of specific neuronal fates is restricted in time and space in the developing CNS through integration of extrinsic morphogen signals and intrinsic determinants. Morphogens impose regional characteristics on neural progenitors and establish distinct progenitor domains. Such domains are defined by unique expression patterns of fate determining transcription factors. These processes of neuronal fate specification can be recapitulated in vitro using pluripotent stem cells. In this review, we focus on the generation of dopamine neurons and motor neurons, which are induced at ventral positions of the neural tube through Sonic hedgehog (Shh) signaling, and defined at anteroposterior positions by fibroblast growth factor (Fgf) 8, Wnt1, and retinoic acid (RA). In vitro utilization of these morphogenic signals typically results in the generation of multiple neuronal cell types, which are defined at the intersection of these signals. If the purpose of in vitro neurogenesis is to generate one cell type only, further lineage restriction can be accomplished by forced expression of specific transcription factors in a permissive environment. Alternatively, cell-sorting strategies allow for selection of neuronal progenitors or mature neurons. However, modeling development, disease and prospective therapies in a dish could benefit from structured heterogeneity, where desired neurons are appropriately synaptically connected and thus better reflect the three-dimensional structure of that region. By modulating the extrinsic environment to direct sequential generation of neural progenitors within a domain, followed by self-organization and synaptic establishment, a reductionist model of that brain region could be created. Here we review recent advances in neuronal fate induction in vitro, with a focus on the interplay between cell intrinsic and extrinsic factors, and discuss the implications for studying development and disease in a dish.

  8. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. II. CHARACTERIZATION OF SPECTRAL STRUCTURE WITH ELECTROMAGNETIC SIMULATIONS AND ITS SCIENCE IMPLICATIONS

    Ewall-Wice, Aaron; Hewitt, Jacqueline; Neben, Abraham R. [MIT Kavli Institute for Cosmological Physics, Cambridge, MA, 02139 (United States); Bradley, Richard; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia [National Radio Astronomy Observatory, Charlottesville, VA (United States); Deboer, David; Parsons, Aaron; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S. [Department of Astronomy, University of California, Berkeley, CA (United States); Aguirre, James [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, PA (United States); Bowman, Judd; Thyagarajan, Nithyanandan [Arizona State University, School of Earth and Space Exploration, Tempe, AZ 85287 (United States); Venter, Mariet [Department of Electrical and Electronic Engineering, Stellenbosch University, Stellenbosch, SA (South Africa); Acedo, Eloy de Lera [Cavendish Laboratory, University of Cambridge, Cambridge (United Kingdom); and others

    2016-11-10

    We use time-domain electromagnetic simulations to determine the spectral characteristics of the Hydrogen Epoch of Reionization Arrays (HERA) antenna. These simulations are part of a multi-faceted campaign to determine the effectiveness of the dish’s design for obtaining a detection of redshifted 21 cm emission from the epoch of reionization. Our simulations show the existence of reflections between HERA’s suspended feed and its parabolic dish reflector that fall below -40 dB at 150 ns and, for reasonable impedance matches, have a negligible impact on HERA’s ability to constrain EoR parameters. It follows that despite the reflections they introduce, dishes are effective for increasing the sensitivity of EoR experiments at a relatively low cost. We find that electromagnetic resonances in the HERA feed’s cylindrical skirt, which is intended to reduce cross coupling and beam ellipticity, introduces significant power at large delays (-40 dB at 200 ns), which can lead to some loss of measurable Fourier modes and a modest reduction in sensitivity. Even in the presence of this structure, we find that the spectral response of the antenna is sufficiently smooth for delay filtering to contain foreground emission at line-of-sight wave numbers below k {sub ∥} ≲ 0.2 h Mpc{sup -1}, in the region where the current PAPER experiment operates. Incorporating these results into a Fisher Matrix analysis, we find that the spectral structure observed in our simulations has only a small effect on the tight constraints HERA can achieve on parameters associated with the astrophysics of reionization.

  9. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects.

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong; Say, Yee-How

    2012-06-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respectively, while salted fish was least preferred and least frequently consumed. Males had a significantly higher intake frequency of at least 6 of the salty foods, but the preference of most salty foods was not significantly different between genders. Ethnic Chinese significantly preferred more and took more frequently traditional and conventional Malaysian foods like asam laksa (a Malaysian salty-sour-spicy noodle in fish stock), salted biscuits and salted vegetable, while Indians have more affinity and frequency towards eating salty Western foods. Body Mass Index was significantly negatively correlated with the intake frequency of canned/packet soup and salted fish while waist circumference was significantly positively correlated with the preference of instant noodle. Also, an increased preference of potato chips and intake frequency of salted biscuits seemed to lead to a decreased WHR. Other than these, all the other overweight/obesity indicators did not seem to fully correlate with the salty food preference and intake frequency. Nevertheless, the preference and intake frequency of asam laksa seemed to be significant negative predictors for blood pressures. Finally, increased preference and intake frequency of high sodium shrimp paste (belacan)-based foods like asam laksa and belacan fried rice seemed to discourage discretionary salt use. In conclusion, the preference and intake frequency of the high sodium belacan-based dish asam laksa seems to be a good predictor for ethnic

  10. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. II. CHARACTERIZATION OF SPECTRAL STRUCTURE WITH ELECTROMAGNETIC SIMULATIONS AND ITS SCIENCE IMPLICATIONS

    Ewall-Wice, Aaron; Hewitt, Jacqueline; Neben, Abraham R.; Bradley, Richard; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia; Deboer, David; Parsons, Aaron; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S.; Aguirre, James; Bowman, Judd; Thyagarajan, Nithyanandan; Venter, Mariet; Acedo, Eloy de Lera

    2016-01-01

    We use time-domain electromagnetic simulations to determine the spectral characteristics of the Hydrogen Epoch of Reionization Arrays (HERA) antenna. These simulations are part of a multi-faceted campaign to determine the effectiveness of the dish’s design for obtaining a detection of redshifted 21 cm emission from the epoch of reionization. Our simulations show the existence of reflections between HERA’s suspended feed and its parabolic dish reflector that fall below -40 dB at 150 ns and, for reasonable impedance matches, have a negligible impact on HERA’s ability to constrain EoR parameters. It follows that despite the reflections they introduce, dishes are effective for increasing the sensitivity of EoR experiments at a relatively low cost. We find that electromagnetic resonances in the HERA feed’s cylindrical skirt, which is intended to reduce cross coupling and beam ellipticity, introduces significant power at large delays (-40 dB at 200 ns), which can lead to some loss of measurable Fourier modes and a modest reduction in sensitivity. Even in the presence of this structure, we find that the spectral response of the antenna is sufficiently smooth for delay filtering to contain foreground emission at line-of-sight wave numbers below k ∥ ≲ 0.2 h Mpc -1 , in the region where the current PAPER experiment operates. Incorporating these results into a Fisher Matrix analysis, we find that the spectral structure observed in our simulations has only a small effect on the tight constraints HERA can achieve on parameters associated with the astrophysics of reionization.

  11. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong

    2012-01-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respectively, while salted fish was least preferred and least frequently consumed. Males had a significantly higher intake frequency of at least 6 of the salty foods, but the preference of most salty foods was not significantly different between genders. Ethnic Chinese significantly preferred more and took more frequently traditional and conventional Malaysian foods like asam laksa (a Malaysian salty-sour-spicy noodle in fish stock), salted biscuits and salted vegetable, while Indians have more affinity and frequency towards eating salty Western foods. Body Mass Index was significantly negatively correlated with the intake frequency of canned/packet soup and salted fish while waist circumference was significantly positively correlated with the preference of instant noodle. Also, an increased preference of potato chips and intake frequency of salted biscuits seemed to lead to a decreased WHR. Other than these, all the other overweight/obesity indicators did not seem to fully correlate with the salty food preference and intake frequency. Nevertheless, the preference and intake frequency of asam laksa seemed to be significant negative predictors for blood pressures. Finally, increased preference and intake frequency of high sodium shrimp paste (belacan)-based foods like asam laksa and belacan fried rice seemed to discourage discretionary salt use. In conclusion, the preference and intake frequency of the high sodium belacan-based dish asam laksa seems to be a good predictor for ethnic

  12. Preliminary designs for 25 kWe advanced Stirling conversion systems for dish electric applications

    Shaltens, Richard K.; Schreiber, Jeffrey G.

    Under the Department of Energy's (DOE) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for terrestrial Solar Distributed Heat Receivers. The Stirling engine has been identified by Sandia as one of the most promising engines for terrestrial applications. The Stirling engine also has the potential to meet DOE's performance and cost goals. The NASA Lewis Research Center is conducting Stirling engine technology development activities directed toward a dynamic power source for space applications. Space power systems requirements include high reliability, very long life, low vibration and high efficiency. The free-piston Stirling engine has the potential for future high power space conversion systems, either nuclear or solar powered. Although both applications appear to be quite different, their requirements complement each other. Preliminary designs feature a free-piston Stirling engine, a liquid metal heat transport system, and a means to provide nominally 25 kW electric power to a utility grid while meeting DOE's performance and long term cost goals. The Cummins design incorporates a linear alternator to provide the electrical output, while the STC design generates electrical power indirectly through a hydraulic pump/motor coupled to an induction generator. Both designs for the ASCS's will use technology which can reasonably be expected to be available in the early 1990's.

  13. Bridging health technology assessment (HTA with multicriteria decision analyses (MCDA: field testing of the EVIDEM framework for coverage decisions by a public payer in Canada

    Tony Michèle

    2011-11-01

    Full Text Available Abstract Background Consistent healthcare decisionmaking requires systematic consideration of decision criteria and evidence available to inform them. This can be tackled by combining multicriteria decision analysis (MCDA and Health Technology Assessment (HTA. The objective of this study was to field-test a decision support framework (EVIDEM, explore its utility to a drug advisory committee and test its reliability over time. Methods Tramadol for chronic non-cancer pain was selected by the health plan as a case study relevant to their context. Based on extensive literature review, a by-criterion HTA report was developed to provide synthesized evidence for each criterion of the framework (14 criteria for the MCDA Core Model and 6 qualitative criteria for the Contextual Tool. During workshop sessions, committee members tested the framework in three steps by assigning: 1 weights to each criterion of the MCDA Core Model representing individual perspective; 2 scores for tramadol for each criterion of the MCDA Core Model using synthesized data; and 3 qualitative impacts of criteria of the Contextual Tool on the appraisal. Utility and reliability of the approach were explored through discussion, survey and test-retest. Agreement between test and retest data was analyzed by calculating intra-rater correlation coefficients (ICCs for weights, scores and MCDA value estimates. Results The framework was found useful by the drug advisory committee in supporting systematic consideration of a broad range of criteria to promote a consistent approach to appraising healthcare interventions. Directly integrated in the framework as a "by-criterion" HTA report, synthesized evidence for each criterion facilitated its consideration, although this was sometimes limited by lack of relevant data. Test-retest analysis showed fair to good consistency of weights, scores and MCDA value estimates at the individual level (ICC ranging from 0.676 to 0.698, thus lending some

  14. Combined approach for finding susceptibility genes in DISH/chondrocalcinosis families: whole-genome-wide linkage and IBS/IBD studies.

    Couto, Ana Rita; Parreira, Bruna; Thomson, Russell; Soares, Marta; Power, Deborah M; Stankovich, Jim; Armas, Jácome Bruges; Brown, Matthew A

    2017-01-01

    Twelve families with exuberant and early-onset calcium pyrophosphate dehydrate chondrocalcinosis (CC) and diffuse idiopathic skeletal hyperostosis (DISH), hereafter designated DISH/CC, were identified in Terceira Island, the Azores, Portugal. Ninety-two (92) individuals from these families were selected for whole-genome-wide linkage analysis. An identity-by-descent (IBD) analysis was performed in 10 individuals from 5 of the investigated pedigrees. The chromosome area with the maximal logarithm of the odds score (1.32; P =0.007) was not identified using the IBD/identity-by-state (IBS) analysis; therefore, it was not investigated further. From the IBD/IBS analysis, two candidate genes, LEMD3 and RSPO4 , were identified and sequenced. Nine genetic variants were identified in the RSPO4 gene; one regulatory variant (rs146447064) was significantly more frequent in control individuals than in DISH/CC patients ( P =0.03). Four variants were identified in LEMD3 , and the rs201930700 variant was further investigated using segregation analysis. None of the genetic variants in RSPO4 or LEMD3 segregated within the studied families. Therefore, although a major genetic effect was shown to determine DISH/CC occurrence within these families, the specific genetic variants involved were not identified.

  15. 3D intestinal organoids in metabolic research: virtual reality in a dish.

    Tsakmaki, Anastasia; Fonseca Pedro, Patricia; Bewick, Gavin A

    2017-12-01

    The advent of near physiological organoid technology has produced a step change in our understanding of stem cells and has provided the research community with a powerful new cell based tool to model human physiology and disease. We review the pros and cons of intestinal organoid culture systems. The molecular and genetic tools to manipulate them and how they are being used to answer fundamental questions in metabolic research, including the function of enteroendocrine cells in health and disease. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Prevalence of diffuse idiopathic skeletal hyperostosis (DISH) of the whole spine and its association with lumbar spondylosis and knee osteoarthritis: the ROAD study.

    Kagotani, Ryohei; Yoshida, Munehito; Muraki, Shigeyuki; Oka, Hiroyuki; Hashizume, Hiroshi; Yamada, Hiroshi; Enyo, Yoshio; Nagata, Keiji; Ishimoto, Yuyu; Teraguchi, Masatoshi; Tanaka, Sakae; Nakamura, Kozo; Kawaguchi, Hiroshi; Akune, Toru; Yoshimura, Noriko

    2015-03-01

    We aimed to assess the prevalence of diffuse idiopathic skeletal hyperostosis (DISH) and its association with lumbar spondylosis (LS) and knee osteoarthritis (KOA) using a population-based cohort study entitled Research on Osteoarthritis/osteoporosis Against Disability (ROAD). In the baseline ROAD study, which was performed between 2005 and 2007, 1,690 participants in mountainous and coastal areas underwent anthropometric measurements and radiographic examinations of the whole spine (cervical, thoracic, and lumbar) and both knees. They also completed an interviewer-administered questionnaire. Presence of DISH was diagnosed according to Resnick criteria, and LS and KOA were defined as Kellgren-Lawrence (KL) grade ≥3. Among the 1,690 participants, whole-spine radiographs of 1,647 individuals (97.5%; 573 men, 1,074 women; mean age, 65.3 years) were evaluated. Prevalence of DISH was 10.8% (men 22.0%, women 4.8%), and was significantly higher in older participants (presence of DISH 72.3 years, absence of DISH 64.4 years) and mainly distributed at the thoracic spine (88.7%). Logistic regression analysis revealed that presence of DISH was significantly associated with older age [+1 year, odds ratio (OR): 1.06, 95% confidence interval (CI): 1.03-1.14], male sex (OR: 5.55, 95% CI: 3.57-8.63), higher body mass index (+1 kg/m(2), OR: 1.08, 95% CI: 1.02-1.14), presence of LS (KL2 vs KL0: 1, OR: 5.50, 95% CI: 2.81-10.8) (KL ≥3 vs KL0: 1, OR: 4.09, 95% CI: 2.08-8.03), and presence of KOA (KL ≥3 vs KL0: 1, OR: 1.89, 95% CI: 1.14-3.10) after adjusting for smoking, alcohol consumption, and residential area (mountainous vs coastal). This cross-sectional population-based study clarified the prevalence of DISH in general inhabitants and its significant association with LS and severe KOA.

  17. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study

    Pauline Ducrot

    2016-07-01

    Full Text Available Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., “nutritional balance of the dish”, constraints (e.g., “my cooking skills”, pleasure (e.g., “originality of the dish”, specific diets (e.g., “my health status”, and organization (e.g., “what I planned to eat”. A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval: 0.62–0.67, whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10–1.19 and specific diets (OR = 1.19 (95% CI: 1.17–1.22. No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  18. A Dish-based Semi-quantitative Food Frequency Questionnaire for Assessment of Dietary Intakes in Epidemiologic Studies in Iran: Design and Development.

    Keshteli, Ah; Esmaillzadeh, Ahmad; Rajaie, Somayeh; Askari, Gholamreza; Feinle-Bisset, Christine; Adibi, Peyman

    2014-01-01

    Earlier forms of food frequency questionnaire (FFQ) used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ). Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a novel FFQ using Harvard FFQ as a model. THE FOLLOWING STEPS WERE TAKEN TO DEVELOP THE QUESTIONNAIRE: Construction of a list of commonly consumed Iranian foods, definition of portion sizes, design of response options for consumption frequency of each food item and finally a pilot test of the preliminary DFQ. From a comprehensive list of foods and mixed dishes, we included those that were nutrient-rich, consumed reasonably often or contributed to between-person variations. We focused on mixed dishes, rather than their ingredients, along with foods. To shorten the list, the related food items or mixed dishes were categorized together in one food group. These exclusions resulted in a list of 106 foods or dishes in the questionnaire. The portion sizes used in the FFQ were obtained from our earlier studies that used dietary recalls and food records. The frequency response options for the food list varied from 6-9 choices from "never or less than once a month" to "12 or more times per day". The DFQ could be a reasonable dietary assessment tool for future epidemiological studies in the country. Validation studies are required to assess the validity and reliability of this newly developed questionnaire.

  19. A Dish-based Semi-quantitative food frequency questionnaire for assessment of dietary intakes in epidemiologic studies in Iran: Design and development

    Ammar Hassanzadeh Keshteli

    2014-01-01

    Full Text Available Background: Earlier forms of food frequency questionnaire (FFQ used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ. Methods: Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a novel FFQ using Harvard FFQ as a model. Results: The following steps were taken to develop the questionnaire: Construction of a list of commonly consumed Iranian foods, definition of portion sizes, design of response options for consumption frequency of each food item and finally a pilot test of the preliminary DFQ. From a comprehensive list of foods and mixed dishes, we included those that were nutrient-rich, consumed reasonably often or contributed to between-person variations. We focused on mixed dishes, rather than their ingredients, along with foods. To shorten the list, the related food items or mixed dishes were categorized together in one food group. These exclusions resulted in a list of 106 foods or dishes in the questionnaire. The portion sizes used in the FFQ were obtained from our earlier studies that used dietary recalls and food records. The frequency response options for the food list varied from 6-9 choices from "never or less than once a month" to "12 or more times per day". Conclusions: The DFQ could be a reasonable dietary assessment tool for future epidemiological studies in the country. Validation studies are required to assess the validity and reliability of this newly developed questionnaire.

  20. Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation

    Qui, Songgang [Temple University; Galbraith, Ross [Infinia

    2013-01-23

    This final report summarizes the final results of the Phase II Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation project being performed by Infinia Corporation for the U.S. Department of Energy under contract DE-FC36-08GO18157 during the project period of September 1, 2009 - August 30, 2012. The primary objective of this project is to demonstrate the practicality of integrating thermal energy storage (TES) modules, using a suitable thermal salt phase-change material (PCM) as its medium, with a dish/Stirling engine; enabling the system to operate during cloud transients and to provide dispatchable power for 4 to 6 hours after sunset. A laboratory prototype designed to provide 3 kW-h of net electrical output was constructed and tested at Infinia's Ogden Headquarters. In the course of the testing, it was determined that the system's heat pipe network - used to transfer incoming heat from the solar receiver to both the Stirling generator heater head and to the phase change salt - did not perform to expectations. The heat pipes had limited capacity to deliver sufficient heat energy to the generator and salt mass while in a charging mode, which was highly dependent on the orientation of the device (vertical versus horizontal). In addition, the TES system was only able to extract about 30 to 40% of the expected amount of energy from the phase change salt once it was fully molten. However, the use of heat pipes to transfer heat energy to and from a thermal energy storage medium is a key technical innovation, and the project team feels that the limitations of the current device could be greatly improved with further development. A detailed study of manufacturing costs using the prototype TES module as a basis indicates that meeting DOE LCOE goals with this hardware requires significant efforts. Improvement can be made by implementing aggressive cost-down initiatives in design and materials

  1. SQUID-based Nondestructive Testing Instrument of Dished Niobium Sheets for SRF Cavities

    Q. S. Shu; I. Ben-Zvi; G. Cheng; I. M. Phipps; J. T. Susta; P. Kneisel; G. Myneni; J. Mast; R. Selim

    2007-01-01

    Currently available technology can only inspect flat sheets and allow the elimination of defective flat sheets before the expensive forming and machining of the SRF cavity half-cells, but it does not eliminate the problem of remaining or uncovered surface impurities after partial chemical etching of the half-cells, nor does it detect any defects that may have been added during the fabrication of the half-cells. AMAC has developed a SQUID scanning system based on eddy current technique that allows the scanning of curved Nb samples that are welded to make superconducting RF cavity half-cells. AMAC SQUID scanning system successfully located the defects (Ta macro particles about 100 mm diameter) in a flat Nb sample (top side) and was able to also locate the defects in a cylindrical surface sample (top side). It is more significant that the system successfully located the defects on the backside of the flat sample and curved sample or 3-mm from the top surface. The 3-D SQUID-based Nondestructive instrument will be further optimized and improved in making SRF cavities and allow inspection and detection during cavity manufacturing for achieving highest accelerating fields

  2. Phage-mediated counting by the naked eye of miRNA molecules at attomolar concentrations in a Petri dish

    Zhou, Xin; Cao, Peng; Zhu, Ye; Lu, Wuguang; Gu, Ning; Mao, Chuanbin

    2015-10-01

    The ability to count biomolecules such as cancer-biomarker miRNAs with the naked eye is seemingly impossible in molecular diagnostics. Here, we show an ultrasensitive naked-eye-counting strategy for quantifying miRNAs by employing T7 phage--a bacteria-specific virus nanoparticle--as a surrogate. The phage is genetically engineered to become fluorescent and capable of binding a miRNA-capturing gold nanoparticle (GNP) in a one-to-one manner. Target miRNAs crosslink the resultant phage-GNP couple and miRNA-capturing magnetic microparticles, forming a sandwich complex containing equimolar phage and miRNA. The phage is then released from the complex and developed into one macroscopic fluorescent plaque in a Petri dish by plating it in a host bacterial medium. Counting the plaques by the naked eye enables the quantification of miRNAs with detection limits of ~3 and ~5 aM for single-target and two-target miRNAs, respectively. This approach offers ultrasensitive and convenient quantification of disease biomarkers by the naked eye.

  3. Effect of lime juice on Vibrio parahaemolyticus and Salmonella enterica inactivation during the preparation of the raw fish dish ceviche.

    Mathurand, Prateek; Schaffner, Donald W

    2013-06-01

    Ceviche is a raw fish dish common in Peru and other Latin American counties. The most characteristic feature of ceviche is the use of lime juice for marinating or "cooking" the raw fish. Confirmed cases of cholera in Peru, New Jersey, and Florida have been associated with ceviche. Although the effect of organic acids on pathogenic bacteria has been well characterized, few data exist on the effect of these acids in seafood systems. The objective of the study was to evaluate the effects of lime juice marination on pathogens likely to be present in ceviche. Tilapia (Oreochromis niloticus) fillet pieces were inoculated with Vibrio parahaemolyticus and Salmonella enterica (>7 log CFU/g) and incubated at 25 and 4°C for 30 or 120 min in the presence of fresh lime juice at concentrations typical for the preparation of ceviche. Similar levels of cells were also inoculated into fresh lime juice without tilapia. Surviving cells were enumerated on selective (xylose lysine Tergitol 4 and thiosulfate-bile-citrate-sucrose) and nonselective (tryptic soy agar) media. V. parahaemolyticus levels were reduced to below detection limits (∼5-log reduction) under all conditions studied. Salmonella strains on tilapia were much more resistant to inactivation and were only slightly reduced (∼1- to 2-log reduction). Salmonella and V. parahaemolyticus inoculated directly into lime juice without tilapia were all reduced to below detection limits (∼5-log reduction). A typical ceviche recipe reduces V. parahaemolyticus risk significantly but is less effective for control of S. enterica.

  4. Liquid dish washing soap: An excellent substitute for xylene and alcohol in hematoxylin and eosin staining procedure

    Surekha Ramulu

    2012-01-01

    Full Text Available Aims: Liquid dish washing solution (DWS was used as a substitute for xylene to dewax tissue sections during hematoxylin and eosin (H and E staining. The aim was to test and compare the hypothesis that xylene-ethanol free (XEF sections deparaffinized with diluted DWS are better than or at par with the conventional H and E sections. Materials and Methods: Fifty paraffin-embedded tissue blocks was included. One section was stained with conventional HandE (group A and the other with XEF HandE (group B staining method. Slides were scored for parameters: nuclear, cytoplasmic, clarity, uniformity, and crispness of staining. Z test was used for statistical analysis. For accuracy of diagnosis, sensitivity, specificity, positive predictive value, and negative predictive value were tested. Results: Adequate nuclear staining was noted in 94% in group A and 96% in group B, -adequate cytoplasmic staining in 92% in group A and 86% in group B, clarity in 94% of group A and 96% of group B sections, uniform staining in 92% of group A and 80% of group B sections, crisp stain in 96% of group A and 88% of group B sections, and 94% of group A sections stained adequately for diagnosis as compared with 90% in group B sections. Conclusion: Liquid DWS can be used as an alternative and effective substitute to xylene and ethanol in routine HandE staining procedure.

  5. Formation of dish-like holes and a channel structure in electrodeposition of copper under hydrogen co-deposition

    Nikolic, N.D.; Pavlovic, Lj.J.; Pavlovic, M.G.; Popov, K.I.

    2007-01-01

    Copper electrodeposition from acid sulfate solutions at an overpotential of 1000 mV, which is about 250 mV outside the plateau of the limiting diffusion current density, was examined by the determination of the average current efficiency of hydrogen evolution and by the scanning electron microscopic (SEM) analysis of the morphology of the formed copper deposits. Craters or holes formed due to the attachment hydrogen bubbles were the dominant morphological forms of copper deposits obtained at this overpotential. In dependence of the concentration of Cu (II) ions in the plating solution, the two types of holes or craters were formed. One type of holes is obtained by electrodeposition from a solution with a concentration of Cu (II) ions of 0.075 M CuSO 4 in 0.50 M H 2 SO 4 , and a honeycomb-like structure was formed from these holes. The other types of holes are formed from a solution with a higher concentration of Cu (II) ions (0.60 M CuSO 4 in 0.50 M H 2 SO 4 ) and the formed holes were dish-like. A mixture of both types of holes was obtained by electrodeposition from 0.30 M CuSO 4 in 0.50 M H 2 SO 4 . The obtained morphologies of copper deposits are discussed in terms of the effect of hydrogen evolution on the hydrodynamic conditions in the plating solution

  6. Studying effects of Magnolol on alpha-particle induced bystander effects using PADC-film based dishes

    Wong, T.P.W.; Tse, A.K.W.; Fong, W.F.; Yu, K.N.

    2009-01-01

    Radiation-induced bystander effect refers to the biological response found in cells (called bystander cells) which are not irradiated directly by ionizing radiation but are next to cells irradiated directly by ionizing radiation. In the present paper, the effects of Magnolol, an extract from the bark of Magnolia officinalis which is used as a traditional Chinese medicine, were studied on alpha-particle induced bystander effects. In our experiments, Chinese hamster ovary (CHO) cells were cultured in PADC-film based dishes and were irradiated with low fluences of alpha particles passing through the PADC films. The precise number of cells traversed or missed by alpha particles could be determined by studying the alpha-particle tracks developed on the PADC films upon subsequent chemical etching. TdT-mediated dUTP Nick-End Labeling (TUNEL) assay was employed to analyze the biological response of bystander cells in terms of DNA strand breaks. With the pretreatment of Magnolol, the DNA strand breaks in bystander cells were reduced, which showed that the alpha-particle induced bystander effects were suppressed with the presence of Magnolol. Since Magnolol is an antioxidant which can scavenge reactive oxygen species (ROS), our results give support to that ROS play a role in the bystander signal transmission in our experiments.

  7. Studying effects of Magnolol on alpha-particle induced bystander effects using PADC-film based dishes

    Wong, T.P.W. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon Tong (Hong Kong); Tse, A.K.W.; Fong, W.F. [Research and Development Division, School of Chinese Medicine, Hong Kong Baptist University, Baptist University Road, Kowloon Tong (Hong Kong); Yu, K.N., E-mail: peter.yu@cityu.edu.h [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon Tong (Hong Kong)

    2009-10-15

    Radiation-induced bystander effect refers to the biological response found in cells (called bystander cells) which are not irradiated directly by ionizing radiation but are next to cells irradiated directly by ionizing radiation. In the present paper, the effects of Magnolol, an extract from the bark of Magnolia officinalis which is used as a traditional Chinese medicine, were studied on alpha-particle induced bystander effects. In our experiments, Chinese hamster ovary (CHO) cells were cultured in PADC-film based dishes and were irradiated with low fluences of alpha particles passing through the PADC films. The precise number of cells traversed or missed by alpha particles could be determined by studying the alpha-particle tracks developed on the PADC films upon subsequent chemical etching. TdT-mediated dUTP Nick-End Labeling (TUNEL) assay was employed to analyze the biological response of bystander cells in terms of DNA strand breaks. With the pretreatment of Magnolol, the DNA strand breaks in bystander cells were reduced, which showed that the alpha-particle induced bystander effects were suppressed with the presence of Magnolol. Since Magnolol is an antioxidant which can scavenge reactive oxygen species (ROS), our results give support to that ROS play a role in the bystander signal transmission in our experiments.

  8. Effect of the phase change material in a solar receiver on thermal performance of parabolic dish collector

    Senthil Ramalingam

    2017-01-01

    Full Text Available In this work, the use of phase change material in the circular tank solar receiver is proposed for a 16 m2 Scheffler parabolic dish solar concentrator to improve the heat transfer in the receiver. Magnesium chloride hexahydrate with melting temperature of 117°C is selected as the phase change material in the annular space of the receiver with rectangular fins inside the phase change material. Experimental work is carried out to analyze heat transfer from the receiver to heat transfer fluid with and without phase change material in the inner periphery. Energy and exergy efficiency are determined from the measurements of solar radiation intensity, receiver temperature, surroundings temperature, heat transfer fluid inlet and outlet temperatures, storage tank temperature, and wind speed. The experiments were conducted in SRM University, Chennai, India (latitude: 13° 5′ N, longitude: 80°16′ E in April 2014. Use of phase change material in receiver periphery increased energy efficiency by 5.62%, exergy efficiency by 12.8% and decreased time to reach the boiling point of water by 20% when compared with the receiver without phase change material.

  9. Performance analysis of dish solar stirling power system; Stirling engine wo mochiita taiyonetsu hatsuden system no seino yosoku

    Tsuchiya, K; Yamaguchi, I [Meiji University, Tokyo (Japan); Naito, Y; Momose, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

    1996-10-27

    In order to estimate the performance of the dish solar Stirling power system, matching and control of each component system were studied, and the performance of the 25kWe class power system was estimated on the basis of direct solar radiation measured in Miyako island, Okinawa. Application of a Stirling engine to solar heat power generation is highly effective in spite of its small scale. The total system is composed of a converging system, heat receiver, engine/generator system and control system. As the simulation result, the generator output is nearly proportional to direct solar radiation, and the system efficiency approaches to a certain constant value with an increase in direct solar radiation. As accumulated solar radiation is large, the influence of slope error of the converging mirror is comparatively small. The optimum aperture opening ratio of the heat receiver determined on the basis of mean direct solar radiation (accumulated solar radiation/{Delta}t (simulated operation time of the system)), corresponds to the primary approximation of the opening ratio for a maximum total generated output under variable direct solar radiation. 6 refs., 6 figs., 1 tab.

  10. Solar reforming of methane in a direct absorption catalytic reactor on a parabolic dish. 2: Modeling and analysis

    Skocypec, Russell D.; Hogan, Roy E., Jr.; Muir, James F.

    1991-01-01

    The catalytically enhanced solar absorption receiver (CAESAR) experiment was conducted to determine the thermal, chemical, and mechanical performance of a commercial-scale, dish-mounted, direct catalytic absorption receiver (DCAR) reactor over a range of steady state and transient (cloud) operating conditions. The focus of the experiment is on global performance such as receiver efficiencies and overall methane conversion; it was not intended to provide data for code validation. A numerical model was previously developed to provide guidance in the design of the absorber. The one-dimensional, planar and steady-state model incorporates, the following energy transfer mechanisms: solar and infrared radiation, heterogeneous chemical reaction, conduction in the solid phase, and convection between the fluid and solid phases. A number of upgrades to the model and improved property values are presented here. Model predictions are shown to bound the experimental axial thermocouple data when experimental uncertainties are included. Global predictions are made using a technique in which the incident solar flux distribution is subdivided into flux contour bands. Model predictions for each band are then spatially integrated to provide global predictions such as reactor efficiencies and methane conversions. Global predictions are shown to compare well with experimental data. Reactor predictions for anticipated operating conditions suggest a further decrease in optical density at the front of the absorber inner disk may be beneficial. The need to conduct code-validation experiments is identified as being essential in improving the confidence in the capability to predict large-scale reactor operation.

  11. A simple beam analyser

    Lemarchand, G.

    1977-01-01

    (ee'p) experiments allow to measure the missing energy distribution as well as the momentum distribution of the extracted proton in the nucleus versus the missing energy. Such experiments are presently conducted on SACLAY's A.L.S. 300 Linac. Electrons and protons are respectively analysed by two spectrometers and detected in their focal planes. Counting rates are usually low and include time coincidences and accidentals. Signal-to-noise ratio is dependent on the physics of the experiment and the resolution of the coincidence, therefore it is mandatory to get a beam current distribution as flat as possible. Using new technologies has allowed to monitor in real time the behavior of the beam pulse and determine when the duty cycle can be considered as being good with respect to a numerical basis

  12. Pathway-based analyses.

    Kent, Jack W

    2016-02-03

    New technologies for acquisition of genomic data, while offering unprecedented opportunities for genetic discovery, also impose severe burdens of interpretation and penalties for multiple testing. The Pathway-based Analyses Group of the Genetic Analysis Workshop 19 (GAW19) sought reduction of multiple-testing burden through various approaches to aggregation of highdimensional data in pathways informed by prior biological knowledge. Experimental methods testedincluded the use of "synthetic pathways" (random sets of genes) to estimate power and false-positive error rate of methods applied to simulated data; data reduction via independent components analysis, single-nucleotide polymorphism (SNP)-SNP interaction, and use of gene sets to estimate genetic similarity; and general assessment of the efficacy of prior biological knowledge to reduce the dimensionality of complex genomic data. The work of this group explored several promising approaches to managing high-dimensional data, with the caveat that these methods are necessarily constrained by the quality of external bioinformatic annotation.

  13. Chefs move to schools. A pilot examination of how chef-created dishes can increase school lunch participation and fruit and vegetable intake.

    Just, David R; Wansink, Brian; Hanks, Andrew S

    2014-12-01

    To demonstrate the feasibility of introducing a main dish designed by a professional chef in the National School Lunch Program and to document the impact on child participation, a chef was recruited to design pizza to be served in an upstate New York school district. The pizza was designed to meet both the cost and ingredient requirements of the NSLP. High school students were significantly more likely to select the pizza prepared by the chef. While the chef had no significant impact on main dish consumption given selection, more students took a vegetable and vegetable consumption increased by 16.5%. This pilot study demonstrates the plausibility of using chefs to boost participation in the school lunch program, and potentially increase nutrition through side selection, among high school students. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. A Dish-based Semi-quantitative food frequency questionnaire for assessment of dietary intakes in epidemiologic studies in Iran: Design and development

    Ammar Hassanzadeh Keshteli; Ahmad Esmaillzadeh; Somayeh Rajaie; Gholamreza Askari; Christine Feinle-Bisset; Peyman Adibi

    2014-01-01

    Background: Earlier forms of food frequency questionnaire (FFQ) used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ). Methods: Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a nove...

  15. Associations between motives for dish choice during home-meal preparation and diet quality in French adults: findings from the NutriNet-Santé study.

    Ducrot, Pauline; Méjean, Caroline; Fassier, Philippine; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2017-03-01

    A number of motives such as constraints or pleasure have been suggested to influence dish choices during home-meal preparation. However, no study has evaluated how the importance conferred to these motives potentially influence diet quality. The present study aims at investigating the difference in diet quality according to the importance attached by individuals to various dish choice motives. The importance of twenty-seven criteria related to dish choices on weekdays was evaluated among 48 010 French adults from the NutriNet-Santé study. ANCOVA and logistic regression models, adjusted for sociodemographic and lifestyle factors, were used to evaluate the association between the importance attached to dish choice motives (yes v. no) and energy and food group intakes, as well as adherence to French nutritional guidelines (modified Programme National Nutrition Santé-Guideline Score (mPNNS-GS)). A higher adherence to nutritional guidelines was observed in individuals attaching importance to a healthy diet (mPNNS-GS score 7·87 (sd 0·09) v. 7·39 (sd 0·09)) and specific diets (mPNNS-GS score 7·73 (sd 0·09) v. 7·53 (sd 0·09)), compared with those who attached little/no importance (all Pfoods compared with their respective counterparts (all Pmotives, that is, constraints, pleasure and organisation, only small differences were observed. The main difference in diet quality was related to the importance placed on a healthy diet. Although a causal link should be demonstrated, our findings suggested that strategies aiming at enabling people to take into account diet quality during home-meal preparation might be effective levers to promote healthy eating.

  16. Performance evaluation of a stand-alone solar dish Stirling system for power generation suitable for off-grid rural electrification

    Kadri, Y.; Hadj Abdallah, H.

    2016-01-01

    Highlights: • Estimation of the output temperature reached by 2 m parabolic dish. • Output power estimation for uncontrollable load was done using Matlab®. • Validation of the proposed system under Tunisian conditions for rural electrification. - Abstract: The development of green power generation such as solar systems that have become a great interest for several countries especially for Tunisia as it presents a significant solar potential. For this purpose, this research has investigated the feasibility and the performance of standalone solar dish/Stirling micro generation plant for rural electrification. The considered hybrid system includes solar dish/Stirling engine, permanent magnet synchronous generator and a storage battery. To start with, thermal modeling and simulation have been carried out using Matlab® for the solar-driven Stirling heat engine system composed of an Alpha Stirling engine, a solar collector and a receiver, in which the radiation, convection, conduction and radiation heat loss have been taken into consideration for the selected design. For numerical validation of the receiver’s thermal model, simulation results were compared with experimental measurements reported for the EURODISH system with a reasonable degree of agreement. Second, the generated torque driving the generator has been estimated by the Adiabatic model of URIELI based on the classical fourth-order Runge-Kutta. In order for an autonomous control, the dish generator is connected to the load via power electronic converters where the bidirectional power flow is possible by the use of two voltage source converters in a back-to-back configuration. They are referred to as Stirling/generator side converter and load side inverter, both are oriented control by space vector pulse width modulation. In this context, the Stirling side converter is used to adjust the synchronous generator while the inverter controls the power flow between the direct current bus and the

  17. Psychiatry in a Dish

    Ilieva, Mirolyba; Fex Svenningsen, Åsa; Thorsen, Morten

    2018-01-01

    , disturbances in cell-cell communication, and an unbalanced ratio between certain neuronal populations. All those processes are highly dependent on the interconnectivity and three-dimensional organizations of the brain. Moreover, in order to gain a deeper understanding of the complex neurobiology of autism......Autism spectrum disorders are a group of pervasive neurodevelopmental conditions with heterogeneous etiology, characterized by deficits in social cognition, communication, and behavioral flexibility. Despite an increasing scientific effort to find the pathophysiological explanations for the disease...

  18. From soil to dish

    Preuthun, J.; Brink, M.; Rantavaara, A.; Runolfsson, H.; Salbu, B.

    1997-12-01

    EKO-3,4 is the first step towards a regular Nordic cooperation within nuclear emergency preparedness in the area of agriculture and foodstuffs. A collective Nordic handbook concerning limitation of nuclear release consequences in agriculture and food products is in preparation. Maximum permissible doses in foodstuffs, administrative procedures in case of a nuclear accident, the communication system among the respective national emergency centers, are a few examples of problems the handbook would cover. (EG)

  19. Workload analyse of assembling process

    Ghenghea, L. D.

    2015-11-01

    The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

  20. The Comparison of Photovoltaic with Small Solar Dish Stirling for Solar Home System 50 W{sub p} in Thailand, Medium Insolation Nature

    Snidvongs, E. S.; Jindaruj, S.

    2006-07-01

    The Thai government initiated a project entitled Solar Home System which involved the provision of standalone Photovoltaic 50 Wp for houses without transmission lines in remote areas, 300,000 units. These units are provided at a low price with the government supporting half of the cost and the rest paid by the owners in installments. So far, more than 150,000 units have been installed and it is expected that the whole project would be completed by the end of the year 2005. A purpose of this research is to compare the original Thai government's Solar Home PV System with the new 50 Wp Small Solar Thermal Dish Stirling System in terms of their advantages and disadvantages for Thailand. The result of this would serve as a guide for the users to select the most suitable system in terms of price, maintenance, cost, economy, performance, reliability, and efficiency. Such comparison will be presented in the form of descriptive, photographs, statistics, and tables. As for the data involved, part of this is based on active fact such as construction cost, material cost, labor cost, rate of inflation, rate of interest. While some of these derives from the experience of researcher as well as facts and figures from Thai governments publications such as operation and maintenance cost. In addition to that some data are taken from basic experiments conducted either by the various universities and the researcher own laboratory. These include solar insolation, PV data and Stirling engine test with electric heater. And, of course, some data are based on simple estimation and prediction. Thailand is a country of 550 w/m2 with high humidity, soft-land and medium insolation. It locates near the equator at latitude 5 12 N, longitude 96 106 E. By using a parabolic shape satellite dish with solar tracker and a 60 W Four Cylinders gamma type Stirling engine with sinusoidal gear linear link, low offset space, and solid thermal storage to act as buffer between the solar energy and the

  1. Manufacturing cost analysis of a parabolic dish concentrator (General Electric design) for solar thermal electric power systems in selected production volumes

    1981-01-01

    The manufacturing cost of a General Electric 12 meter diameter concentrator was estimated. This parabolic dish concentrator for solar thermal system was costed in annual production volumes of 100 - 1,000 - 5,000 - 10,000 - 50,000 100,000 - 400,000 and 1,000,000 units. Presented for each volume are the costs of direct labor, material, burden, tooling, capital equipment and buildings. Also presented is the direct labor personnel and factory space requirements. All costs are based on early 1981 economics.

  2. Enumeration of Salmonellae in Table Eggs, Pasteurized Egg Products, and Egg-Containing Dishes by Using Quantitative Real-Time PCR

    Jakočiūnė, Džiuginta; Pasquali, Frédérique; da Silva, Cristiana Soares

    2014-01-01

    PCR) was employed for enumeration of salmonellae in different matrices: table eggs, pasteurized egg products, and egg-containing dishes. Salmonella enterica serovar Enteritidis and S. enterica serovar Tennessee were used to artificially contaminate these matrices. The results showed a linear regression between...... the numbers of salmonellae and the quantification cycle (Cq) values for all matrices used, with the exception of pasteurized egg white. Standard curves were constructed by using both stationary-phase cells and heat-stressed cells, with similar results. Finally, this method was used to evaluate the fate...

  3. Open-Ended Waveguide Measurement and Numerical Simulation of the Reflectivity of Petri Dish Supported Skin Cell Monolayers in the mm-wave Range

    Beneduci, Amerigo; Chidichimo, Giuseppe

    2012-05-01

    Open-ended waveguide reflectometry is a promising tool for permittivity and other material properties calculation at mm-waves (30-300 GHz). Measurement of the reflection coefficient does not require sample manipulation, allowing in vivo and in vitro non destructive studies on cells. Here we used this technique for measuring the power reflection coefficient (reflectivity) of water and Petri dish supported human skin melanoma and keratinocyte cell cultures, in the 53-72 GHz frequency range. The dependence of the reflectivity on polystyrene or glass thickness of the Petri base plate and on the cell layer thickness was analyzed. Permittivity data were then easily retrieved by using a plane wave-dominant mode approach for formulating the reflectivity at the aperture of the flange-mounted open-ended rectangular waveguide probe. Limits and validity of such an approximate approach were analyzed and compared with full-wave near field formulations for which magnitude and phase of the reflection coefficient must be measured and solved using complicated systems of integral equations and extensive numerical calculation. Finally, Petri dish reflectivity measured by the open-ended waveguide method was compared with that numerically simulated under far-field exposure conditions used in a large number of in vitro studies. Such an analysis showed that, under certain conditions, open-ended reflectivity values approach the far field ones.

  4. Mitogenomic analyses from ancient DNA

    Paijmans, Johanna L. A.; Gilbert, Tom; Hofreiter, Michael

    2013-01-01

    The analysis of ancient DNA is playing an increasingly important role in conservation genetic, phylogenetic and population genetic analyses, as it allows incorporating extinct species into DNA sequence trees and adds time depth to population genetics studies. For many years, these types of DNA...... analyses (whether using modern or ancient DNA) were largely restricted to the analysis of short fragments of the mitochondrial genome. However, due to many technological advances during the past decade, a growing number of studies have explored the power of complete mitochondrial genome sequences...... yielded major progress with regard to both the phylogenetic positions of extinct species, as well as resolving population genetics questions in both extinct and extant species....

  5. L'analyse ergonomique des besoins en amont de la conception de technologies émergente: le cas de la Réalité Augmentée pour la formation à la maintenance automobile

    Anastassova, Margarita

    2006-01-01

    The goal of this PhD work is to compare the advantages and the disadvantages of different methods used for user-needs analysis in early design of an emerging technology, namely Augmented Reality (AR). This technology should be applied to the training of automotive maintenance technicians. After a literature review on the ergonomics issues of AR for maintenance and training, we present four studies using three methods for user-needs analysis (semi-directed interviews, observation-based task an...

  6. Wet Gas Airfoil Analyses

    Larsen, Tarjei Thorrud

    2011-01-01

    Subsea wet gas compression renders new possibilities for cost savings and enhanced gas recovery on existing gas wells. Technology like this opens to make traditional offshore processing plants redundant. With new technology, follows new challenges. Multiphase flows is regarded as a complex field of study, and increased knowledge on the fundamental mechanisms regarding wet gas flow is of paramount importance to the efficiency and stability of the wet gas compressor. The scope of this work was ...

  7. Study on the radiation flux and temperature distributions of the concentrator-receiver system in a solar dish/Stirling power facility

    Li Zhigang; Tang Dawei; Du Jinglong; Li Tie

    2011-01-01

    Uniform heater temperature and high optical-thermal efficiency are crucial for the reliable and economical operation of a Solar Dish/Stirling engine facility. The Monte-Carlo ray-tracing method is utilized to predict the radiation flux distributions of the concentrator-receiver system. The ray-tracing method is first validated by experiment, then the radiation flux profiles on the solar receiver surface for faceted real concentrator and ideal paraboloidal concentrator, irradiated by Xe-arc lamps and real sun, for different aperture positions and receiver shapes are analyzed, respectively. The resulted radiation flux profiles are subsequently transferred to a CFD code as boundary conditions to numerically simulate the fluid flow and conjugate heat transfer in the receiver cavity by coupling the radiation, natural convection and heat conduction together, and the CFD method is also validated through experiment. The results indicate that a faceted concentrator in combination with a solar simulator composed of 12 Xe-arc lamps is advantageous to drive the solar Stirling engine for all-weather indoor tests. Based on the simulation results, a solar receiver-Stirling heater configuration is designed to achieve a considerably uniform temperature distribution on the heater head tubes while maintaining a high efficiency of 60.7%. - Highlights: → Radiation flux in Dish/Stirling system is analyzed by validated ray-tracing method. → Temperature field on the solar receiver is analyzed by a validated CFD method. → Effects of Xe-arc lamp solar simulator and faceted real concentrator are analyzed. → Effects of different receiver positions and receiver shapes are investigated. → A Stirling heater configuration is presented with uniform temperature field.

  8. Translation of Human-Induced Pluripotent Stem Cells: From Clinical Trial in a Dish to Precision Medicine.

    Sayed, Nazish; Liu, Chun; Wu, Joseph C

    2016-05-10

    The prospect of changing the plasticity of terminally differentiated cells toward pluripotency has completely altered the outlook for biomedical research. Human-induced pluripotent stem cells (iPSCs) provide a new source of therapeutic cells free from the ethical issues or immune barriers of human embryonic stem cells. iPSCs also confer considerable advantages over conventional methods of studying human diseases. Since its advent, iPSC technology has expanded with 3 major applications: disease modeling, regenerative therapy, and drug discovery. Here we discuss, in a comprehensive manner, the recent advances in iPSC technology in relation to basic, clinical, and population health. Copyright © 2016 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

  9. CRISPR/Cas9 genome editing in human pluripotent stem cells: Harnessing human genetics in a dish.

    González, Federico

    2016-07-01

    Because of their extraordinary differentiation potential, human pluripotent stem cells (hPSCs) can differentiate into virtually any cell type of the human body, providing a powerful platform not only for generating relevant cell types useful for cell replacement therapies, but also for modeling human development and disease. Expanding this potential, structures resembling human organs, termed organoids, have been recently obtained from hPSCs through tissue engineering. Organoids exhibit multiple cell types self-organizing into structures recapitulating in part the physiology and the cellular interactions observed in the organ in vivo, offering unprecedented opportunities for human disease modeling. To fulfill this promise, tissue engineering in hPSCs needs to be supported by robust and scalable genome editing technologies. With the advent of the CRISPR/Cas9 technology, manipulating the genome of hPSCs has now become an easy task, allowing modifying their genome with superior precision, speed, and throughput. Here we review current and potential applications of the CRISPR/Cas9 technology in hPSCs and how they contribute to establish hPSCs as a model of choice for studying human genetics. Developmental Dynamics 245:788-806, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  10. Laser Beam Focus Analyser

    Nielsen, Peter Carøe; Hansen, Hans Nørgaard; Olsen, Flemming Ove

    2007-01-01

    the obtainable features in direct laser machining as well as heat affected zones in welding processes. This paper describes the development of a measuring unit capable of analysing beam shape and diameter of lasers to be used in manufacturing processes. The analyser is based on the principle of a rotating......The quantitative and qualitative description of laser beam characteristics is important for process implementation and optimisation. In particular, a need for quantitative characterisation of beam diameter was identified when using fibre lasers for micro manufacturing. Here the beam diameter limits...... mechanical wire being swept through the laser beam at varying Z-heights. The reflected signal is analysed and the resulting beam profile determined. The development comprised the design of a flexible fixture capable of providing both rotation and Z-axis movement, control software including data capture...

  11. Evaluation of the status of science and technology concerning the performance and interpretation of accident analyses using analysis simulators; Ermittlung des Standes von Wissenschaft und Technik bei der Durchfuehrung und Bewertung von Stoerfallanalysen und der Verwendung von Analysesimulatoren

    Pointner, Winfried; Cuesta Morales, Alejandra; Koppers, Vera; Kowalik, Michael; Broecker, Annette; Li, Tianqi; Mayer, Gerhard; Palazzo, Simone; Perin, Yann

    2017-03-15

    The aim of the project is to develop the methodology to perform short-term accident analyses and to clarify scientific-technical questions concerning the reactor and behavior in case of an accident. For short-term reactions it is necessary to provide appropriate analysis tools data and results for the plant specific behavior (reactor core, cooling circuits, containment) for abnormal operation and accidents (design-based and beyond-design accidents). The qualification of the data base and severe accident analyses is part of the project. The analysis simulators were actualized to the most recent version of ATHLET 3.1A.

  12. Contesting Citizenship: Comparative Analyses

    Siim, Birte; Squires, Judith

    2007-01-01

    importance of particularized experiences and multiple ineequality agendas). These developments shape the way citizenship is both practiced and analysed. Mapping neat citizenship modles onto distinct nation-states and evaluating these in relation to formal equality is no longer an adequate approach....... Comparative citizenship analyses need to be considered in relation to multipleinequalities and their intersections and to multiple governance and trans-national organisinf. This, in turn, suggests that comparative citizenship analysis needs to consider new spaces in which struggles for equal citizenship occur...

  13. Status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators. Final report; Ermittlung des Standes von Wissenschaft und Technik bei der Durchfuehrung und Bewertung von Stoerfallanalysen und der Verwendung von Analysesimulatoren. Abschlussbericht

    Draeger, P.; Cester, F.; Erdmann, W.; and others

    2011-12-15

    The final report on the status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators includes the following work packages: uncertainty analysis for an incident in BWR, preparation and evaluation of accident analyses considering the requirements in the reviewed standards, safeguarding of the mixing modeling for the evaluation of re-criticality accidents, answering of recent questions concerning reactor and containment behavior during incidents and accidents, actualization and refinement of data bases for plant specific analysis simulators.

  14. Risico-analyse brandstofpontons

    Uijt de Haag P; Post J; LSO

    2001-01-01

    Voor het bepalen van de risico's van brandstofpontons in een jachthaven is een generieke risico-analyse uitgevoerd. Er is een referentiesysteem gedefinieerd, bestaande uit een betonnen brandstofponton met een relatief grote inhoud en doorzet. Aangenomen is dat de ponton gelegen is in een

  15. Fast multichannel analyser

    Berry, A; Przybylski, M M; Sumner, I [Science Research Council, Daresbury (UK). Daresbury Lab.

    1982-10-01

    A fast multichannel analyser (MCA) capable of sampling at a rate of 10/sup 7/ s/sup -1/ has been developed. The instrument is based on an 8 bit parallel encoding analogue to digital converter (ADC) reading into a fast histogramming random access memory (RAM) system, giving 256 channels of 64 k count capacity. The prototype unit is in CAMAC format.

  16. A fast multichannel analyser

    Berry, A.; Przybylski, M.M.; Sumner, I.

    1982-01-01

    A fast multichannel analyser (MCA) capable of sampling at a rate of 10 7 s -1 has been developed. The instrument is based on an 8 bit parallel encoding analogue to digital converter (ADC) reading into a fast histogramming random access memory (RAM) system, giving 256 channels of 64 k count capacity. The prototype unit is in CAMAC format. (orig.)

  17. A History of Rotorcraft Comprehensive Analyses

    Johnson, Wayne

    2013-01-01

    A history of the development of rotorcraft comprehensive analyses is presented. Comprehensive analyses are digital computer programs that calculate the aeromechanical behavior of the rotor and aircraft, bringing together the most advanced models of the geometry, structure, dynamics, and aerodynamics available in rotary wing technology. The development of the major codes of the last five decades from industry, government, and universities is described. A number of common themes observed in this history are discussed.

  18. Composition of flavonoids in fresh herbs and calculation of flavonoid intake by use of herbs in traditional Danish dishes

    Justesen, U.; Knuthsen, Pia

    2001-01-01

    , coriander, cress, dill, lemon balm, lovage, oregano, parsley, rosemary, sage, spearmint, tarragon, thyme, and watercress) were analysed by HPLC and mass spectrometry. Five major flavonoid aglycones were detected and quantified by HPLC after acid hydrolysis: apigenin, isorhamnetin, kaempferol, luteolin......Many herbs are known as excellent sources of natural antioxidants, and consumption of fresh herbs in the diet may therefore contribute to the daily antioxidant intake. The present study was performed in order to quantify flavonoids in commonly eaten fresh herbs. Fifteen fresh herbs (basil, chives......, and quercetin. The highest levels of flavonoids were found in parsley (510-630 mg apigenin /100 g), lovage (170 mg quercetin/100g), mint (18-100 mg apigenin/ 100 g), and dill (48-110 mg quercetin/100 g). Mass spectrometric detection, using atmospheric pressure chemical ionisation (APCI), was used to verify...

  19. Probabilistic risk model for staphylococcal intoxication from pork-based food dishes prepared in food service establishments in Korea.

    Kim, Hyun Jung; Griffiths, Mansel W; Fazil, Aamir M; Lammerding, Anna M

    2009-09-01

    Foodborne illness contracted at food service operations is an important public health issue in Korea. In this study, the probabilities for growth of, and enterotoxin production by, Staphylococcus aureus in pork meat-based foods prepared in food service operations were estimated by the Monte Carlo simulation. Data on the prevalence and concentration of S. aureus as well as compliance to guidelines for time and temperature controls during food service operations were collected. The growth of S. aureus was initially estimated by using the U.S. Department of Agriculture's Pathogen Modeling Program. A second model based on raw pork meat was derived to compare cell number predictions. The correlation between toxin level and cell number as well as minimum toxin dose obtained from published data was adopted to quantify the probability of staphylococcal intoxication. When data gaps were found, assumptions were made based on guidelines for food service practices. Baseline risk model and scenario analyses were performed to indicate possible outcomes of staphylococcal intoxication under the scenarios generated based on these data gaps. Staphylococcal growth was predicted during holding before and after cooking, and the highest estimated concentration (4.59 log CFU/g for the 99.9th percentile value) of S. aureus was observed in raw pork initially contaminated with S. aureus and held before cooking. The estimated probability for staphylococcal intoxication was very low, using currently available data. However, scenario analyses revealed an increased possibility of staphylococcal intoxication when increased levels of initial contamination in the raw meat, andlonger holding time both before and after cooking the meat occurred.

  20. 3D culture models of Alzheimer's disease: a road map to a "cure-in-a-dish".

    Choi, Se Hoon; Kim, Young Hye; Quinti, Luisa; Tanzi, Rudolph E; Kim, Doo Yeon

    2016-12-09

    Alzheimer's disease (AD) transgenic mice have been used as a standard AD model for basic mechanistic studies and drug discovery. These mouse models showed symbolic AD pathologies including β-amyloid (Aβ) plaques, gliosis and memory deficits but failed to fully recapitulate AD pathogenic cascades including robust phospho tau (p-tau) accumulation, clear neurofibrillary tangles (NFTs) and neurodegeneration, solely driven by familial AD (FAD) mutation(s). Recent advances in human stem cell and three-dimensional (3D) culture technologies made it possible to generate novel 3D neural cell culture models that recapitulate AD pathologies including robust Aβ deposition and Aβ-driven NFT-like tau pathology. These new 3D human cell culture models of AD hold a promise for a novel platform that can be used for mechanism studies in human brain-like environment and high-throughput drug screening (HTS). In this review, we will summarize the current progress in recapitulating AD pathogenic cascades in human neural cell culture models using AD patient-derived induced pluripotent stem cells (iPSCs) or genetically modified human stem cell lines. We will also explain how new 3D culture technologies were applied to accelerate Aβ and p-tau pathologies in human neural cell cultures, as compared the standard two-dimensional (2D) culture conditions. Finally, we will discuss a potential impact of the human 3D human neural cell culture models on the AD drug-development process. These revolutionary 3D culture models of AD will contribute to accelerate the discovery of novel AD drugs.

  1. Nuclear enterprises at the Institute for Energy Technology - IFE. A socio-economic cost/benefit analysis; Nukleaere virksomheter ved Institutt for energiteknikk - IFE. En samfunnsoekonomisk kost/nytte-analyse

    2008-03-15

    A cost-benefit analysis concerning the research reactors JEEP II at Kjeller and the Halden Reactor in Halden, operated by the Institute for Energy Technology. It is concluded for both of the reactors that the benefits of continued operations are outweigh the cost. Financing, accident risk, waste management and nuclear competence are some of the aspects treated. The Norwegian Ministry of Trade and Industry initiated the evaluation on behalf of the Norwegian Government

  2. Possible future HERA analyses

    Geiser, Achim

    2015-12-01

    A variety of possible future analyses of HERA data in the context of the HERA data preservation programme is collected, motivated, and commented. The focus is placed on possible future analyses of the existing ep collider data and their physics scope. Comparisons to the original scope of the HERA pro- gramme are made, and cross references to topics also covered by other participants of the workshop are given. This includes topics on QCD, proton structure, diffraction, jets, hadronic final states, heavy flavours, electroweak physics, and the application of related theory and phenomenology topics like NNLO QCD calculations, low-x related models, nonperturbative QCD aspects, and electroweak radiative corrections. Synergies with other collider programmes are also addressed. In summary, the range of physics topics which can still be uniquely covered using the existing data is very broad and of considerable physics interest, often matching the interest of results from colliders currently in operation. Due to well-established data and MC sets, calibrations, and analysis procedures the manpower and expertise needed for a particular analysis is often very much smaller than that needed for an ongoing experiment. Since centrally funded manpower to carry out such analyses is not available any longer, this contribution not only targets experienced self-funded experimentalists, but also theorists and master-level students who might wish to carry out such an analysis.

  3. Biomass feedstock analyses

    Wilen, C.; Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1996-12-31

    The overall objectives of the project `Feasibility of electricity production from biomass by pressurized gasification systems` within the EC Research Programme JOULE II were to evaluate the potential of advanced power production systems based on biomass gasification and to study the technical and economic feasibility of these new processes with different type of biomass feed stocks. This report was prepared as part of this R and D project. The objectives of this task were to perform fuel analyses of potential woody and herbaceous biomasses with specific regard to the gasification properties of the selected feed stocks. The analyses of 15 Scandinavian and European biomass feed stock included density, proximate and ultimate analyses, trace compounds, ash composition and fusion behaviour in oxidizing and reducing atmospheres. The wood-derived fuels, such as whole-tree chips, forest residues, bark and to some extent willow, can be expected to have good gasification properties. Difficulties caused by ash fusion and sintering in straw combustion and gasification are generally known. The ash and alkali metal contents of the European biomasses harvested in Italy resembled those of the Nordic straws, and it is expected that they behave to a great extent as straw in gasification. Any direct relation between the ash fusion behavior (determined according to the standard method) and, for instance, the alkali metal content was not found in the laboratory determinations. A more profound characterisation of the fuels would require gasification experiments in a thermobalance and a PDU (Process development Unit) rig. (orig.) (10 refs.)

  4. Technology transfer by multinationals

    Kostyantyn Zuzik

    2003-01-01

    The paper analyses the issue of technology transfer by multinational corporations. The following questions are explored: (a) world market of technologies, the role of MNCs (b) Choice of the technology transfer mode, Dunning's OLI-theory as a factor of the choice of the mode of transfer (c) measurement and profitability of technology transfer (d) transfer of technology through partnerships, JVs, alliances and through M&As (e) aspects of technology transfer by services multinationals. Paper uti...

  5. Performance and cost benefits associated with nonimaging secondary concentrators used in point-focus dish solar thermal applications

    Ogallagher, J.; Winston, R.

    1987-09-01

    Using nonimaging secondary concentrators in point-focus applications may permit the development of more cost-effective concentrator systems by either improving performance or reducing costs. Secondaries may also increase design flexibility. The major objective of this study was to develop as complete an understanding as possible of the quantitative performance and cost effects associated with deploying nonimaging secondary concentrators at the focal zone of point-focus solar thermal concentrators. A performance model was developed that uses a Monte Carlo ray-trace procedure to determine the focal plane distribution of a paraboloidal primary as a function of optical parameters. It then calculates the corresponding optimized concentration and thermal efficiency as a function of temperature with and without the secondary. To examine the potential cost benefits associated with secondaries, a preliminary model for the rational optimization of performance versus cost trade-offs was developed. This model suggests a possible 10 to 20 percent reduction in the cost of delivered energy when secondaries are used. This is a lower limit, and the benefits may even be greater if using a secondary permits the development of inexpensive primary technologies for which the performance would not otherwise be viable.

  6. Theorising and Analysing Academic Labour

    Thomas Allmer

    2018-01-01

    Full Text Available The aim of this article is to contextualise universities historically within capitalism and to analyse academic labour and the deployment of digital media theoretically and critically. It argues that the post-war expansion of the university can be considered as medium and outcome of informational capitalism and as a dialectical development of social achievement and advanced commodification. The article strives to identify the class position of academic workers, introduces the distinction between academic work and labour, discusses the connection between academic, information and cultural work, and suggests a broad definition of university labour. It presents a theoretical model of working conditions that helps to systematically analyse the academic labour process and to provide an overview of working conditions at universities. The paper furthermore argues for the need to consider the development of education technologies as a dialectics of continuity and discontinuity, discusses the changing nature of the forces and relations of production, and the impact on the working conditions of academics in the digital university. Based on Erik Olin Wright’s inclusive approach of social transformation, the article concludes with the need to bring together anarchist, social democratic and revolutionary strategies for establishing a socialist university in a commons-based information society.

  7. CFD analyses in regulatory practice

    Bloemeling, F.; Pandazis, P.; Schaffrath, A.

    2012-01-01

    Numerical software is used in nuclear regulatory procedures for many problems in the fields of neutron physics, structural mechanics, thermal hydraulics etc. Among other things, the software is employed in dimensioning and designing systems and components and in simulating transients and accidents. In nuclear technology, analyses of this kind must meet strict requirements. Computational Fluid Dynamics (CFD) codes were developed for computing multidimensional flow processes of the type occurring in reactor cooling systems or in containments. Extensive experience has been accumulated by now in selected single-phase flow phenomena. At the present time, there is a need for development and validation with respect to the simulation of multi-phase and multi-component flows. As insufficient input by the user can lead to faulty results, the validity of the results and an assessment of uncertainties are guaranteed only through consistent application of so-called Best Practice Guidelines. The authors present the possibilities now available to CFD analyses in nuclear regulatory practice. This includes a discussion of the fundamental requirements to be met by numerical software, especially the demands upon computational analysis made by nuclear rules and regulations. In conclusion, 2 examples are presented of applications of CFD analysis to nuclear problems: Determining deboration in the condenser reflux mode of operation, and protection of the reactor pressure vessel (RPV) against brittle failure. (orig.)

  8. AMS analyses at ANSTO

    Lawson, E.M. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia). Physics Division

    1998-03-01

    The major use of ANTARES is Accelerator Mass Spectrometry (AMS) with {sup 14}C being the most commonly analysed radioisotope - presently about 35 % of the available beam time on ANTARES is used for {sup 14}C measurements. The accelerator measurements are supported by, and dependent on, a strong sample preparation section. The ANTARES AMS facility supports a wide range of investigations into fields such as global climate change, ice cores, oceanography, dendrochronology, anthropology, and classical and Australian archaeology. Described here are some examples of the ways in which AMS has been applied to support research into the archaeology, prehistory and culture of this continent`s indigenous Aboriginal peoples. (author)

  9. AMS analyses at ANSTO

    Lawson, E.M.

    1998-01-01

    The major use of ANTARES is Accelerator Mass Spectrometry (AMS) with 14 C being the most commonly analysed radioisotope - presently about 35 % of the available beam time on ANTARES is used for 14 C measurements. The accelerator measurements are supported by, and dependent on, a strong sample preparation section. The ANTARES AMS facility supports a wide range of investigations into fields such as global climate change, ice cores, oceanography, dendrochronology, anthropology, and classical and Australian archaeology. Described here are some examples of the ways in which AMS has been applied to support research into the archaeology, prehistory and culture of this continent's indigenous Aboriginal peoples. (author)

  10. Analyses of MHD instabilities

    Takeda, Tatsuoki

    1985-01-01

    In this article analyses of the MHD stabilities which govern the global behavior of a fusion plasma are described from the viewpoint of the numerical computation. First, we describe the high accuracy calculation of the MHD equilibrium and then the analysis of the linear MHD instability. The former is the basis of the stability analysis and the latter is closely related to the limiting beta value which is a very important theoretical issue of the tokamak research. To attain a stable tokamak plasma with good confinement property it is necessary to control or suppress disruptive instabilities. We, next, describe the nonlinear MHD instabilities which relate with the disruption phenomena. Lastly, we describe vectorization of the MHD codes. The above MHD codes for fusion plasma analyses are relatively simple though very time-consuming and parts of the codes which need a lot of CPU time concentrate on a small portion of the codes, moreover, the codes are usually used by the developers of the codes themselves, which make it comparatively easy to attain a high performance ratio on the vector processor. (author)

  11. Uncertainty Analyses and Strategy

    Kevin Coppersmith

    2001-01-01

    The DOE identified a variety of uncertainties, arising from different sources, during its assessment of the performance of a potential geologic repository at the Yucca Mountain site. In general, the number and detail of process models developed for the Yucca Mountain site, and the complex coupling among those models, make the direct incorporation of all uncertainties difficult. The DOE has addressed these issues in a number of ways using an approach to uncertainties that is focused on producing a defensible evaluation of the performance of a potential repository. The treatment of uncertainties oriented toward defensible assessments has led to analyses and models with so-called ''conservative'' assumptions and parameter bounds, where conservative implies lower performance than might be demonstrated with a more realistic representation. The varying maturity of the analyses and models, and uneven level of data availability, result in total system level analyses with a mix of realistic and conservative estimates (for both probabilistic representations and single values). That is, some inputs have realistically represented uncertainties, and others are conservatively estimated or bounded. However, this approach is consistent with the ''reasonable assurance'' approach to compliance demonstration, which was called for in the U.S. Nuclear Regulatory Commission's (NRC) proposed 10 CFR Part 63 regulation (64 FR 8640 [DIRS 101680]). A risk analysis that includes conservatism in the inputs will result in conservative risk estimates. Therefore, the approach taken for the Total System Performance Assessment for the Site Recommendation (TSPA-SR) provides a reasonable representation of processes and conservatism for purposes of site recommendation. However, mixing unknown degrees of conservatism in models and parameter representations reduces the transparency of the analysis and makes the development of coherent and consistent probability statements about projected repository

  12. “A por gauchos in chiripá...”. Expresiones criollistas en el teatro ídish argentino (1910-1930

    Susana Skura

    2014-06-01

    Full Text Available En Argentina, entre 1890 y 1920, se desarrolló el fenómeno criollista, consistente en la difusión del gusto por lo gaucho como moda popular de consumos y usos culturales. Coincidió con el auge del proceso inmigratorio y atravesó los debates sobre el primer nacionalismo cultural y los festejos del centenario patrio. A partir del reciente hallazgo de una colección de textos dramáticos escritos en ídish con abundantes préstamos del español rioplatense trasliterados, y reunidos por la Fundación Iwo de Buenos Aires, se explora la inclusión de prácticas y terminología de la cultura dominante en un teatro escrito y actuado en la lengua de inmigración, como un aspecto del proceso de transculturación de los inmigrantes ashkenazíes y de las primeras generaciones nacidas en las colonias agrícolas judías argentinas.

  13. A comparative study to evaluate liquid dish washing soap as an alternative to xylene and alcohol in deparaffinization and hematoxylin and eosin staining.

    Pandey, Pinki; Dixit, Alok; Tanwar, Aparna; Sharma, Anuradha; Mittal, Sanjeev

    2014-07-01

    Our study presents a new deparaffinizing and hematoxylin and eosin (H and E) staining method that involves the use of easily available, nontoxic and eco-friendly liquid diluted dish washing soap (DWS) by completely eliminating expensive and hazardous xylene and alcohol from deparaffinizing and rehydration prior to staining, staining and from dehydration prior to mounting. The aim was to evaluate and compare the quality of liquid DWS treated xylene and alcohol free (XAF) sections with that of the conventional H and E sections. A total of 100 paraffin embedded tissue blocks from different tissues were included. From each tissue block, one section was stained with conventional H and E (normal sections) and the other with XAF H and E (soapy sections) staining method. Slides were scored using five parameters: Nuclear, cytoplasmic, clarity, uniformity, and crispness of staining. Z-test was used for statistical analysis. Soapy sections scored better for cytoplasmic (90%) and crisp staining (95%) with a statistically significant difference. Whereas for uniformity of staining, normal sections (88%) scored over soapy sections (72%) (Z = 2.82, P 0.05). Liquid DWS is a safe and efficient alternative to xylene and alcohol in deparaffinization and routine H and E staining procedure. We are documenting this project that can be used as a model for other histology laboratories.

  14. EEG analyses with SOBI.

    Glickman, Matthew R.; Tang, Akaysha (University of New Mexico, Albuquerque, NM)

    2009-02-01

    The motivating vision behind Sandia's MENTOR/PAL LDRD project has been that of systems which use real-time psychophysiological data to support and enhance human performance, both individually and of groups. Relevant and significant psychophysiological data being a necessary prerequisite to such systems, this LDRD has focused on identifying and refining such signals. The project has focused in particular on EEG (electroencephalogram) data as a promising candidate signal because it (potentially) provides a broad window on brain activity with relatively low cost and logistical constraints. We report here on two analyses performed on EEG data collected in this project using the SOBI (Second Order Blind Identification) algorithm to identify two independent sources of brain activity: one in the frontal lobe and one in the occipital. The first study looks at directional influences between the two components, while the second study looks at inferring gender based upon the frontal component.

  15. Analysing Access Control Specifications

    Probst, Christian W.; Hansen, René Rydhof

    2009-01-01

    When prosecuting crimes, the main question to answer is often who had a motive and the possibility to commit the crime. When investigating cyber crimes, the question of possibility is often hard to answer, as in a networked system almost any location can be accessed from almost anywhere. The most...... common tool to answer this question, analysis of log files, faces the problem that the amount of logged data may be overwhelming. This problems gets even worse in the case of insider attacks, where the attacker’s actions usually will be logged as permissible, standard actions—if they are logged at all....... Recent events have revealed intimate knowledge of surveillance and control systems on the side of the attacker, making it often impossible to deduce the identity of an inside attacker from logged data. In this work we present an approach that analyses the access control configuration to identify the set...

  16. Outline of sustainable energy technology for flower bulb businesses. An economic analysis of decentralized energy production options; Verkenning duurzame energietechnieken toepasbaar op bloembollenbedrijven. Een economische analyse van decentrale opwekkingsmogelijkheden

    Van der Putten, K. [Praktijkonderzoek Plant en Omgeving PPO, Bloembollen, Boomkwekerij en Fruit, Lisse (Netherlands)

    2011-05-15

    An overview is offered of the available sustainable energy sources and techniques that are available for decentralized energy generation in the flower bulb sector. By comparing the expected increase of gas and electricity prices to the expected price decrease of new, sustainable technologies, an estimate was made regarding the year in which these techniques will become financially appealing for flower bulb businesses. This comparison takes into account the various growth scenarios and the allocation of subsidies [Dutch] Een overzicht wordt gegeven van beschikbare duurzame energiebronnen en technieken waarmee decentraal energie kan worden opgewekt in de bloembollensector. Door de verwachte stijging van de gas en elektriciteitsprijzen uit te zetten tegen de verwachte prijsdaling van de nieuwe, duurzame technologieen, is een schatting gemaakt van het jaar waarin deze technieken financieel aantrekkelijk worden voor bloembollenbedrijven. Hierbij is rekening gehouden met verschillende groeiscenario's en het wel of niet verkrijgen van subsidie.

  17. Network class superposition analyses.

    Carl A B Pearson

    Full Text Available Networks are often used to understand a whole system by modeling the interactions among its pieces. Examples include biomolecules in a cell interacting to provide some primary function, or species in an environment forming a stable community. However, these interactions are often unknown; instead, the pieces' dynamic states are known, and network structure must be inferred. Because observed function may be explained by many different networks (e.g., ≈ 10(30 for the yeast cell cycle process, considering dynamics beyond this primary function means picking a single network or suitable sample: measuring over all networks exhibiting the primary function is computationally infeasible. We circumvent that obstacle by calculating the network class ensemble. We represent the ensemble by a stochastic matrix T, which is a transition-by-transition superposition of the system dynamics for each member of the class. We present concrete results for T derived from boolean time series dynamics on networks obeying the Strong Inhibition rule, by applying T to several traditional questions about network dynamics. We show that the distribution of the number of point attractors can be accurately estimated with T. We show how to generate Derrida plots based on T. We show that T-based Shannon entropy outperforms other methods at selecting experiments to further narrow the network structure. We also outline an experimental test of predictions based on T. We motivate all of these results in terms of a popular molecular biology boolean network model for the yeast cell cycle, but the methods and analyses we introduce are general. We conclude with open questions for T, for example, application to other models, computational considerations when scaling up to larger systems, and other potential analyses.

  18. Supporting analyses and assessments

    Ohi, J. [National Renewable Energy Lab., Golden, CO (United States)

    1995-09-01

    Supporting analysis and assessments can provide a sound analytic foundation and focus for program planning, evaluation, and coordination, particularly if issues of hydrogen production, distribution, storage, safety, and infrastructure can be analyzed in a comprehensive and systematic manner. The overall purpose of this activity is to coordinate all key analytic tasks-such as technology and market status, opportunities, and trends; environmental costs and benefits; and regulatory constraints and opportunities-within a long-term and systematic analytic foundation for program planning and evaluation. Within this context, the purpose of the project is to help develop and evaluate programmatic pathway options that incorporate near and mid-term strategies to achieve the long-term goals of the Hydrogen Program. In FY 95, NREL will develop a comprehensive effort with industry, state and local agencies, and other federal agencies to identify and evaluate programmatic pathway options to achieve the long-term goals of the Program. Activity to date is reported.

  19. Efficiency of advanced wastewater treatment technologies for the reduction of hormonal activity in effluents and connected surface water bodies by means of vitellogenin analyses in rainbow trout (Oncorhynchus mykiss) and brown trout (Salmo trutta f. fario).

    Henneberg, Anja; Triebskorn, Rita

    2015-01-01

    Endocrine effects in the aquatic environment are in the focus of scientists and media along with debates on the necessity of further steps in wastewater treatment. In the present study VTG responses were compared to evaluate upgrades at wastewater treatment plants (WWTPs). We investigated several advanced sewage treatment technologies at two WWTPs connected to the Schussen, a tributary of Lake Constance, for the reduction of hormonal activity: (1) a powdered activated charcoal filter at the WWTP Langwiese; and (2) a combination of ozonation, sand filter, and granulated activated carbon filter at the WWTP Eriskirch. Rainbow trout and brown trout were either directly exposed to the effluents in aquaria or cages, or in a bypass system flown through by surface water of the Schussen. As a reference, trout were kept in bypass aquaria at the Argen River, which is less influenced by micropollutants. As a biomarker for estrogenicity, we analyzed the yolk precursor protein vitellogenin in immature rainbow trout and brown trout and in trout larvae (100 days post-fertilization) prior to and after the upgrade with the new technologies. Trout of different ages and species were used to detect differences in their sensitivity. At both bypass stations, larvae of brown trout showed significantly higher vitellogenin levels prior to the upgrade compared to negative control levels. Female brown trout exposed at the bypass station downstream of the WWTP showed decreased vitellogenin levels after the upgrade. In 1-year-old immature trout directly exposed to the respective effluents, no significant effects of the upgrades on vitellogenin levels were found. In general, larger effects were observed in brown trout than in rainbow trout, indicating that they are more sensitive test organisms.

  20. Seismic fragility analyses

    Kostov, Marin

    2000-01-01

    In the last two decades there is increasing number of probabilistic seismic risk assessments performed. The basic ideas of the procedure for performing a Probabilistic Safety Analysis (PSA) of critical structures (NUREG/CR-2300, 1983) could be used also for normal industrial and residential buildings, dams or other structures. The general formulation of the risk assessment procedure applied in this investigation is presented in Franzini, et al., 1984. The probability of failure of a structure for an expected lifetime (for example 50 years) can be obtained from the annual frequency of failure, β E determined by the relation: β E ∫[d[β(x)]/dx]P(flx)dx. β(x) is the annual frequency of exceedance of load level x (for example, the variable x may be peak ground acceleration), P(fI x) is the conditional probability of structure failure at a given seismic load level x. The problem leads to the assessment of the seismic hazard β(x) and the fragility P(fl x). The seismic hazard curves are obtained by the probabilistic seismic hazard analysis. The fragility curves are obtained after the response of the structure is defined as probabilistic and its capacity and the associated uncertainties are assessed. Finally the fragility curves are combined with the seismic loading to estimate the frequency of failure for each critical scenario. The frequency of failure due to seismic event is presented by the scenario with the highest frequency. The tools usually applied for probabilistic safety analyses of critical structures could relatively easily be adopted to ordinary structures. The key problems are the seismic hazard definitions and the fragility analyses. The fragility could be derived either based on scaling procedures or on the base of generation. Both approaches have been presented in the paper. After the seismic risk (in terms of failure probability) is assessed there are several approaches for risk reduction. Generally the methods could be classified in two groups. The

  1. Comprendre le processus d'adaptation des demarches d'enseignement en classe de sciences et technologies a l'ecole secondaire: Analyse des besoins percus par les personnes enseignantes en milieu defavorise

    Houde, Sylvie

    Since the implementation of the latest reform in the education programs of Quebec, the adaptation of teaching has taken on an important place in the concerns of all actors in education. However, this adjustment towards the adoption of teaching practices that require more participation on the part of the pupil is not accomplished so easily, particularly in the field of science and technology (ST). In order to gain a better understanding of these processes of adaptation, it is opportune to question ourselves on the factors and dynamics of interest at stake, especially in disadvantaged environments. Such environments are faced with situations where other difficulties coexist: integration of pupils, lack of interest, problems in classroom management, multi-ethnicity, etc. As a result, such difficulties give rise to particular limitations, expressed in the form of needs, by pupils and teachers, likely to have a restrictive effect on the adaptation of teaching practices. Accordingly, our research focuses on the needs perceived by teachers in high school ST classrooms in disadvantaged school environments, since they present a privileged means to better understand the processes involved in the adaptation of practices. The adoption of an ecosystemic perspective, centered on these needs and their contribution towards the dynamics of decision-making, enabled us to better apprehend the complexity of these processes in ST classrooms. We were able to identify the needs perceived by teachers by following the methodology of conceptanalysis of needs, and by combining focus groups with the DRAP software. The results account for the large variety of needs to be considered in the equation of adaptation of teaching practices. These needs generally belong to the classroom system (microsystem). For pupils, they are mainly cognitive needs, but for teachers, they pertain to organization and structure. The influence of these needs on the adaptation processes depends on the interpretation by

  2. Website-analyse

    Thorlacius, Lisbeth

    2009-01-01

    eller blindgyder, når han/hun besøger sitet. Studier i design og analyse af de visuelle og æstetiske aspekter i planlægning og brug af websites har imidlertid kun i et begrænset omfang været under reflektorisk behandling. Det er baggrunden for dette kapitel, som indleder med en gennemgang af æstetikkens......Websitet er i stigende grad det foretrukne medie inden for informationssøgning,virksomhedspræsentation, e-handel, underholdning, undervisning og social kontakt. I takt med denne voksende mangfoldighed af kommunikationsaktiviteter på nettet, er der kommet mere fokus på at optimere design og...... planlægning af de funktionelle og indholdsmæssige aspekter ved websites. Der findes en stor mængde teori- og metodebøger, som har specialiseret sig i de tekniske problemstillinger i forbindelse med interaktion og navigation, samt det sproglige indhold på websites. Den danske HCI (Human Computer Interaction...

  3. A channel profile analyser

    Gobbur, S.G.

    1983-01-01

    It is well understood that due to the wide band noise present in a nuclear analog-to-digital converter, events at the boundaries of adjacent channels are shared. It is a difficult and laborious process to exactly find out the shape of the channels at the boundaries. A simple scheme has been developed for the direct display of channel shape of any type of ADC on a cathode ray oscilliscope display. This has been accomplished by sequentially incrementing the reference voltage of a precision pulse generator by a fraction of a channel and storing ADC data in alternative memory locations of a multichannel pulse height analyser. Alternative channels are needed due to the sharing at the boundaries of channels. In the flat region of the profile alternate memory locations are channels with zero counts and channels with the full scale counts. At the boundaries all memory locations will have counts. The shape of this is a direct display of the channel boundaries. (orig.)

  4. Which is the best solar thermal collection technology for electricity generation in north-west India? Evaluation of options using the analytical hierarchy process

    Nixon, J.D.; Davies, P.A. [Sustainable Environment Research Group, School of Engineering and Applied Science, Aston University, Aston Triangle, Birmingham, B4 7ET (United Kingdom); Dey, P.K. [Aston Business School, Aston University, Aston Triangle, Birmingham, B4 7ET (United Kingdom)

    2010-12-15

    This study of concentrating solar thermal power generation sets out to evaluate the main existing collection technologies using the framework of the Analytical Hierarchy Process (AHP). It encompasses parabolic troughs, heliostat fields, linear Fresnel reflectors, parabolic dishes, compound parabolic concentrators and linear Fresnel lenses. These technologies are compared based on technical, economic and environmental criteria. Within these three categories, numerous sub-criteria are identified; similarly sub-alternatives are considered for each technology. A literature review, thermodynamic calculations and an expert workshop have been used to arrive at quantitative and qualitative assessments. The methodology is applied principally to a case study in Gujarat in north-west India, though case studies based on the Sahara Desert, Southern Spain and California are included for comparison. A sensitivity analysis is carried out for Gujarat. The study concludes that the linear Fresnel lens with a secondary compound parabolic collector, or the parabolic dish reflector, is the preferred technology for north-west India. (author)

  5. Which is the best solar thermal collection technology for electricity generation in north-west India? Evaluation of options using the analytical hierarchy process

    Nixon, J.D.; Dey, P.K.; Davies, P.A.

    2010-01-01

    This study of concentrating solar thermal power generation sets out to evaluate the main existing collection technologies using the framework of the Analytical Hierarchy Process (AHP). It encompasses parabolic troughs, heliostat fields, linear Fresnel reflectors, parabolic dishes, compound parabolic concentrators and linear Fresnel lenses. These technologies are compared based on technical, economic and environmental criteria. Within these three categories, numerous sub-criteria are identified; similarly sub-alternatives are considered for each technology. A literature review, thermodynamic calculations and an expert workshop have been used to arrive at quantitative and qualitative assessments. The methodology is applied principally to a case study in Gujarat in north-west India, though case studies based on the Sahara Desert, Southern Spain and California are included for comparison. A sensitivity analysis is carried out for Gujarat. The study concludes that the linear Fresnel lens with a secondary compound parabolic collector, or the parabolic dish reflector, is the preferred technology for north-west India.

  6. Molecular ecological network analyses.

    Deng, Ye; Jiang, Yi-Huei; Yang, Yunfeng; He, Zhili; Luo, Feng; Zhou, Jizhong

    2012-05-30

    Understanding the interaction among different species within a community and their responses to environmental changes is a central goal in ecology. However, defining the network structure in a microbial community is very challenging due to their extremely high diversity and as-yet uncultivated status. Although recent advance of metagenomic technologies, such as high throughout sequencing and functional gene arrays, provide revolutionary tools for analyzing microbial community structure, it is still difficult to examine network interactions in a microbial community based on high-throughput metagenomics data. Here, we describe a novel mathematical and bioinformatics framework to construct ecological association networks named molecular ecological networks (MENs) through Random Matrix Theory (RMT)-based methods. Compared to other network construction methods, this approach is remarkable in that the network is automatically defined and robust to noise, thus providing excellent solutions to several common issues associated with high-throughput metagenomics data. We applied it to determine the network structure of microbial communities subjected to long-term experimental warming based on pyrosequencing data of 16 S rRNA genes. We showed that the constructed MENs under both warming and unwarming conditions exhibited topological features of scale free, small world and modularity, which were consistent with previously described molecular ecological networks. Eigengene analysis indicated that the eigengenes represented the module profiles relatively well. In consistency with many other studies, several major environmental traits including temperature and soil pH were found to be important in determining network interactions in the microbial communities examined. To facilitate its application by the scientific community, all these methods and statistical tools have been integrated into a comprehensive Molecular Ecological Network Analysis Pipeline (MENAP), which is open

  7. Enhanced migration of murine fibroblast-like 3T3-L1 preadipocytes on type I collagen-coated dish is reversed by silibinin treatment.

    Liu, Xiaoling; Xu, Qian; Liu, Weiwei; Yao, Guodong; Zhao, Yeli; Xu, Fanxing; Hayashi, Toshihiko; Fujisaki, Hitomi; Hattori, Shunji; Tashiro, Shin-Ichi; Onodera, Satoshi; Yamato, Masayuki; Ikejima, Takashi

    2018-04-01

    Migration of fibroblast-like preadipocytes is important for the development of adipose tissue, whereas excessive migration is often responsible for impaired adipose tissue related with obesity and fibrotic diseases. Type I collagen (collagen I) is the most abundant component of extracellular matrix and has been shown to regulate fibroblast migration in vitro, but its role in adipose tissue is not known. Silibinin is a bioactive natural flavonoid with antioxidant and antimetastasis activities. In this study, we found that type I collagen coating promoted the proliferation and migration of murine 3T3-L1 preadipocytes in a dose-dependent manner, implying that collagen I could be an extracellular signal. Regarding the mechanisms of collagen I-stimulated 3T3-L1 migration, we found that NF-κB p65 is activated, including the increased nuclear translocation of NF-κB p65 as well as the upregulation of NF-κB p65 phosphorylation and acetylation, accompanied by the increased expressions of proinflammatory factors and the generation of reactive oxygen species (ROS). Reduction of collagen I-enhanced migration of cells by treatment with silibinin was associated with suppression of NF-κB p65 activity and ROS generation, and negatively correlated with the increasing sirt1 expression. Taken together, the enhanced migration of 3T3-L1 cells induced on collagen I-coated dish is mediated by the activation of NF-κB p65 function and ROS generation that can be alleviated with silibinin by upregulation of sirt1, leading to the repression of NF-κB p65 function and ROS generation.

  8. Effects of Indole-3-Acetic Acid on Germination in Lead Polluted Petri Dish of Citrullus lanatus (Thunberg Matsumura and Nakai, Cucurbitaceae

    Matthew Chidozie Ogwu

    2015-12-01

    Full Text Available Watermelon, Citrullus lanatus (Thunberg Matsumura and Nakai is a tropical fruit vegetable. Indole-3-acetic acid (IAA is a popular phytohormone while lead (Pb is a common environmental pollutant in urban and sub-urban centers. C. lanatus were obtained from Benin City with a view to study the effects of IAA on their germination in Pb polluted environment.  Germination percentage without IAA and Pb treatment in petri dish was significant after ten days. Hastened germination was observed when IAA and lead were used. About 100 % germination was recorded after seven days. This suggests that water melon seeds can initiate growth even in lead polluted environment. Optimum level of 5 ppm IAA with the different levels of lead treatments may be recommended. Most important was that higher concentrations of Pb in the control (without IAA did not inhibit seedling shoot nor root growth. Longest seedling shoot length (cm was 10.33 ± 1.24 and 12.13 ± 2.06 on the seventh and eighth day respectively with the combined treatment levels of 1 ppm IAA and 15 ppm Pb. On the ninth day, 15.27 ± 0.96 was obtained from 1 ppm IAA and 20 ppm Pb. Longest seedling root length (cm values were recorded from the combined treatment levels of 0 ppm IAA and 10 ppm Pb for the seventh (9.10 ± 0.47 and ninth (10.37 ± 1.81 day respectively and 0 ppm and 15 ppm Pb on the eighth (9.37 ± 0.84 day. Significant means were also obtained with the treatment level of 0 and 20 ppm IAA. This present study suggest the germination of C. lanatus under Pb polluted environment may be rescued with optimum IAA.

  9. A model-based analysis for the improvement of electrical energy supply of future offshore windparks by means of biogas technology; Modellbasierte Analyse zur Verbesserung der elektrischen Energiebereitstellung zukuenftiger Offshore-Windparks mittels Biogastechnologie

    Tigges, Martin

    2010-09-06

    Since the beginning of industrial revolution energy supply in Germany was based on fossil fuels. Climatic change, the greenhouse effect, the growth of population on the one hand and shortage on fossil fuels on the other hand and the will to be independent from importing resources from political instable countries are calling for serious changes. The primary modernisation of the current energy supply needs to target a sustainable, generation comprehensive solution. The use of renewable fuels is necessary. Wind energy usage is one of the most promising alternatives within the short-term to middle-term planning of environmental policy. As in Germany nearly all potential habitats on mainland already are tapped, significant development potential is seen at offshore habitats in North as well as Baltic Sea. Germany aims for the allotment of up to 25 GW of offshore wind energy in the North and Baltic Sea till 2025. Electricity generation by wind energy plants subjects to the conditions the volatile characteristics of the wind. Within the planned big offshore wind energy farms comprising more than 80 plants changes in wind velocity as well as directions will lead to fluctuations in energy supply. Up to now the plant resource scheduling needed to react on the users demand. The further development of wind energy and the differences between forecasted and actual wind energy feeds do and will hinder this resource scheduling. New approaches need to be found to be able to ensure the security of energy supplies in Germany. These approaches should be sustainable and therefore be based on the usage of renewable fuels. Within this dissertation possible solutions as well as constraints of the usage of biogas as a nearly CO2 neutral fuel in combination with micro gas turbines adapted to the usage with biogas plants to be able to align the differences between forecasted and actual wind energy supply for a future offshore wind energy plant park are analysed. This combination allows an

  10. NOAA's National Snow Analyses

    Carroll, T. R.; Cline, D. W.; Olheiser, C. M.; Rost, A. A.; Nilsson, A. O.; Fall, G. M.; Li, L.; Bovitz, C. T.

    2005-12-01

    NOAA's National Operational Hydrologic Remote Sensing Center (NOHRSC) routinely ingests all of the electronically available, real-time, ground-based, snow data; airborne snow water equivalent data; satellite areal extent of snow cover information; and numerical weather prediction (NWP) model forcings for the coterminous U.S. The NWP model forcings are physically downscaled from their native 13 km2 spatial resolution to a 1 km2 resolution for the CONUS. The downscaled NWP forcings drive an energy-and-mass-balance snow accumulation and ablation model at a 1 km2 spatial resolution and at a 1 hour temporal resolution for the country. The ground-based, airborne, and satellite snow observations are assimilated into the snow model's simulated state variables using a Newtonian nudging technique. The principle advantages of the assimilation technique are: (1) approximate balance is maintained in the snow model, (2) physical processes are easily accommodated in the model, and (3) asynoptic data are incorporated at the appropriate times. The snow model is reinitialized with the assimilated snow observations to generate a variety of snow products that combine to form NOAA's NOHRSC National Snow Analyses (NSA). The NOHRSC NSA incorporate all of the available information necessary and available to produce a "best estimate" of real-time snow cover conditions at 1 km2 spatial resolution and 1 hour temporal resolution for the country. The NOHRSC NSA consist of a variety of daily, operational, products that characterize real-time snowpack conditions including: snow water equivalent, snow depth, surface and internal snowpack temperatures, surface and blowing snow sublimation, and snowmelt for the CONUS. The products are generated and distributed in a variety of formats including: interactive maps, time-series, alphanumeric products (e.g., mean areal snow water equivalent on a hydrologic basin-by-basin basis), text and map discussions, map animations, and quantitative gridded products

  11. Moralizing Food Technology

    Coff, Christian Eyde

    2015-01-01

    Food technologies are common on many levels in society and used by both food professionals and consumers. Food technologies are not neutral. They inform and shape the behaviour of people. This paper presents a theoretical framework for analysing the mediating role of food technology and its influ...

  12. Teaching with Technology

    Attard, Catherine

    2011-01-01

    New technologies continue to change every aspect of home, life and work: the way people communicate, calculate, analyse, shop, make presentations and socialise. "The Australian Curriculum" acknowledges the importance of teaching and learning with technology by including the use of information and communication technology (ICT) as one of…

  13. Photovoltaic concentrator technology development project. Sixth project integration meeting

    None

    1980-10-01

    Thirty-three abstracts and short papers are presented which describe the current status of research, development, and demonstration of concentrator solar cell technology. Solar concentrators discussed include the parabolic trough, linear focus Fresnel lens, point focus Fresnel lens, and the parabolic dish. Solar cells studied include silicon, GaAs, and AlGaAs. Research on multiple junction cells, combined photovoltaic/thermal collectors, back contact solar cells, and beam splitter modules is described. Concentrator solar cell demonstration programs are reported. Contractor status summaries are given for 33 US DOE concentrator solar cell contracts; a description of the project, project status, and key results to date is included. (WHK)

  14. Here comes the sun. Solar energy technology in the USA

    Van der Wees, G.

    1998-01-01

    An overview is given of the energy policy in the USA with respect to solar energy technology and the marketing of solar energy applications. In particular, attention is paid to the Million Solar Roofs programme, small-scale and medium-scale photovoltaic (PV) systems (Residential PV and Utility Scale PV), solar thermal systems (Parabolic Trough, Power tower, and Solar Dish/Engine). Also examples of passive solar systems are given. Finally, a number of aspects with regard to market implementation, e.g. net-metering. 9 refs

  15. Application of cell sheet technology to bone marrow stromal cell transplantation for rat brain infarct.

    Ito, Masaki; Shichinohe, Hideo; Houkin, Kiyohiro; Kuroda, Satoshi

    2017-02-01

    Bone marrow stromal cells (BMSC) transplantation enhances functional recovery after cerebral infarct, but the optimal delivery route is undetermined. This study was aimed to assess whether a novel cell-sheet technology non-invasively serves therapeutic benefits to ischemic stroke. First, the monolayered cell sheet was engineered by culturing rat BMSCs on a temperature-responsive dish. The cell sheet was analysed histologically and then transplanted onto the ipsilateral neocortex of rats subjected to permanent middle cerebral artery occlusion at 7 days after the insult. Their behaviours and histology were compared with those in the animals treated with direct injection of BMSCs or vehicle over 4 weeks post-transplantation. The cell sheet was 27.9 ± 8.0 μm thick and was composed of 9.8 ± 2.4 × 10 5 cells. Cell sheet transplantation significantly improved motor function when compared with the vehicle-injected animals. Histological analysis revealed that the BMSCs were densely distributed to the neocortex adjacent to the cerebral infarct and expressed neuronal phenotype in the cell sheet-transplanted animals. These findings were almost equal to those for the animals treated with direct BMSC injection. The attachment of the BMSC sheet to the brain surface did not induce reactive astrocytes in the adjacent neocortex, although direct injection of BMSCs profoundly induced reactive astrocytes around the injection site. These findings suggest that the BMSCs in cell sheets preserve their biological capacity of migration and neural differentiation. Cell-sheet technology may enhance functional recovery after ischaemic stroke, using a less invasive method. Copyright © 2014 John Wiley & Sons, Ltd. Copyright © 2014 John Wiley & Sons, Ltd.

  16. MOTION CAPTURE AS A MODERN TECHNOLOGY FOR ANALYSING ERGOMETER ROWING

    Maria Skublewska-Paszkowska

    2016-03-01

    Full Text Available The paper presents a purpose-built laboratory stand consisting of a Vicon motion capture system with reference video cameras, wireless EMG system, Concept 2 Indoor Rower ergometer, wireless heart rate monitor and the Nexus software. A pilot study of people who exercise on the ergometer helped to create a proper configuration of all the components of the laboratory. Moreover, a procedure for carrying out research was developed, which consists of several steps divided into 4 stages: preparation of the motion acquisition system; preparation of the participant; familiarising participants with the technique of rowing, recording their movements and acquiring other measurement signals. Preliminary analysis of the results obtained from heterogeneous signals from various devices showed that all the components of the research stand are mutually compatible and the received signals do not interfere with one another.

  17. Technology Corner: Analysing E-mail Headers For Forensic Investigation

    M. Tariq Banday

    2011-06-01

    Full Text Available Electronic Mail (E-Mail, which is one of the most widely used applications of Internet, has become a global communication infrastructure service.  However, security loopholes in it enable cybercriminals to misuse it by forging its headers or by sending it anonymously for illegitimate purposes, leading to e-mail forgeries. E-mail messages include transit handling envelope and trace information in the form of structured fields which are not stripped after messages are delivered, leaving a detailed record of e-mail transactions.  A detailed header analysis can be used to map the networks traversed by messages, including information on the messaging software and patching policies of clients and gateways, etc. Cyber forensic e-mail analysis is employed to collect credible evidence to bring criminals to justice. This paper projects the need for e-mail forensic investigation and lists various methods and tools used for its realization. A detailed header analysis of a multiple tactic spoofed e-mail message is carried out in this paper. It also discusses various possibilities for detection of spoofed headers and identification of its originator. Further, difficulties that may be faced by investigators during forensic investigation of an e-mail message have been discussed along with their possible solutions.

  18. Efficacy of 1.5% Dish Washing Solution and 95% Lemon Water in Substituting Perilous Xylene as a Deparaffinizing Agent for Routine H and E Staining Procedure: A Short Study

    Anuradha Ananthaneni

    2014-01-01

    Full Text Available Aim. To assess the efficacy of dish washing solution and diluted lemon water in deparaffinizing sections during conventional hematoxylin and eosin staining technique. Objective. The objective is to utilize eco-friendly economical substitute for xylene. Materials and Methods. Using twenty paraffin embedded tissue blocks, three sections each were prepared. One section was stained with conventional H and E method (Group A and the other two sections with xylene-free (XF H and E (Groups B and C. Staining characteristics were compared with xylene and scoring was given. Total score of 3–5 was regarded as adequate for diagnosis and less than that inadequate for diagnosis. Statistical Analysis. Chi-square test, Kruskal Wallis ANOVA test, and Mann-Whitney U test were used. Results. Adequacy of nuclear staining, crispness, and staining for diagnosis were greater in both Groups A and C (100% than Group B (95%. Adequacy of cytoplasmic staining was similar in all the three groups (100%. Group B showed comparatively superior uniform staining and less retention of wax. Conclusion. Dish washing solution or diluted lemon water can be replaced for xylene as deparaffinizing agent in hematoxylin and eosin procedure.

  19. Analyse that! : understanding sustainable design

    Brand, van den G.J.W.; Wit, de M.H.

    2004-01-01

    This paper describes a method for the analysis of sustainable building projects. Sustainable technology measures can easily be misinterpreted, consequently leading to unsustainable building solutions. Our research and educations aims at discovering new approaches for sustainable design. For building

  20. Danish Approaches in Social Studies of Technology

    Munch, Birgitte

    1995-01-01

    Danish contribution to a EU-COST A4 action analysing the emergence of social studies of technology, the Science-Technology-Society field and the 'new sociology' of technology in Europe.......Danish contribution to a EU-COST A4 action analysing the emergence of social studies of technology, the Science-Technology-Society field and the 'new sociology' of technology in Europe....

  1. Sample preparation in foodomic analyses.

    Martinović, Tamara; Šrajer Gajdošik, Martina; Josić, Djuro

    2018-04-16

    Representative sampling and adequate sample preparation are key factors for successful performance of further steps in foodomic analyses, as well as for correct data interpretation. Incorrect sampling and improper sample preparation can be sources of severe bias in foodomic analyses. It is well known that both wrong sampling and sample treatment cannot be corrected anymore. These, in the past frequently neglected facts, are now taken into consideration, and the progress in sampling and sample preparation in foodomics is reviewed here. We report the use of highly sophisticated instruments for both high-performance and high-throughput analyses, as well as miniaturization and the use of laboratory robotics in metabolomics, proteomics, peptidomics and genomics. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  2. Descriptive Analyses of Mechanical Systems

    Andreasen, Mogens Myrup; Hansen, Claus Thorp

    2003-01-01

    Forord Produktanalyse og teknologianalyse kan gennmføres med et bredt socio-teknisk sigte med henblik på at forstå kulturelle, sociologiske, designmæssige, forretningsmæssige og mange andre forhold. Et delområde heri er systemisk analyse og beskrivelse af produkter og systemer. Nærværende kompend...

  3. Analysing and Comparing Encodability Criteria

    Kirstin Peters

    2015-08-01

    Full Text Available Encodings or the proof of their absence are the main way to compare process calculi. To analyse the quality of encodings and to rule out trivial or meaningless encodings, they are augmented with quality criteria. There exists a bunch of different criteria and different variants of criteria in order to reason in different settings. This leads to incomparable results. Moreover it is not always clear whether the criteria used to obtain a result in a particular setting do indeed fit to this setting. We show how to formally reason about and compare encodability criteria by mapping them on requirements on a relation between source and target terms that is induced by the encoding function. In particular we analyse the common criteria full abstraction, operational correspondence, divergence reflection, success sensitiveness, and respect of barbs; e.g. we analyse the exact nature of the simulation relation (coupled simulation versus bisimulation that is induced by different variants of operational correspondence. This way we reduce the problem of analysing or comparing encodability criteria to the better understood problem of comparing relations on processes.

  4. Analysing Children's Drawings: Applied Imagination

    Bland, Derek

    2012-01-01

    This article centres on a research project in which freehand drawings provided a richly creative and colourful data source of children's imagined, ideal learning environments. Issues concerning the analysis of the visual data are discussed, in particular, how imaginative content was analysed and how the analytical process was dependent on an…

  5. Impact analyses after pipe rupture

    Chun, R.C.; Chuang, T.Y.

    1983-01-01

    Two of the French pipe whip experiments are reproduced with the computer code WIPS. The WIPS results are in good agreement with the experimental data and the French computer code TEDEL. This justifies the use of its pipe element in conjunction with its U-bar element in a simplified method of impact analyses

  6. Millifluidic droplet analyser for microbiology

    Baraban, L.; Bertholle, F.; Salverda, M.L.M.; Bremond, N.; Panizza, P.; Baudry, J.; Visser, de J.A.G.M.; Bibette, J.

    2011-01-01

    We present a novel millifluidic droplet analyser (MDA) for precisely monitoring the dynamics of microbial populations over multiple generations in numerous (=103) aqueous emulsion droplets (100 nL). As a first application, we measure the growth rate of a bacterial strain and determine the minimal

  7. Analyser of sweeping electron beam

    Strasser, A.

    1993-01-01

    The electron beam analyser has an array of conductors that can be positioned in the field of the sweeping beam, an electronic signal treatment system for the analysis of the signals generated in the conductors by the incident electrons and a display for the different characteristics of the electron beam

  8. Analysing Information Systems Security In Higher Learning Institutions Of Uganda

    Mugyenyi Raymond

    2017-01-01

    Information communication technology has increased globalisation in higher learning institution all over the world. This has been achieved through introduction of systems that ease operations related to information handling in the institutions. The paper assessed and analysed the information systems security performance status in higher learning institutions of Uganda. The existing policies that govern the information security have also been analysed together with the current status of inform...

  9. Design of the support structure, drive pedestal, and controls for a solar concentrator

    Goldberg, V.R.; Ford, J.L.; Anderson, A.E. (WG Associates, Dallas, TX (United States))

    1991-08-01

    The glass/metal McDonnell-Douglas dish is the state-of-the-art of parabolic dish concentrators. Because of the perceived high production cost of this concentrator, the Department of Energy's Solar Thermal Program is developing stretch-membrane technology for large (75 kWt) solar concentrators for integration with receivers and engines in 25 kWe dish-Stirling systems. The objective of this development effort is to reduce the cost of the concentrator while maintaining the high levels of performance characteristic of glass-metal dishes. Under contract to Sandia National Laboratories, Science Applications International Corporation, Solar Kinetics Inc. and WG Associates are developing a faceted stretched-membrane heliostat technology. This design will result in a low-risk, near-term concentrator for dish-Stirling systems. WG Associates has designed the support structure, drives and tracking controls for this dish. The structure is configured to support 12 stretched-membrane, 3.5-meter diameter facets in a shaped dish configuration. The dish design is sized to power a dish-Stirling system capable of producing 25 kW (electric). In the design of the structure, trade-off studies were conducted to determine the best'' facet arrangement, dish contour, dish focal length, tracking control and walk-off protection. As part of the design, in-depth analyses were performed to evaluate pointing accuracy, compliance with AISC steel design codes, and the economics of fabrication and installation. Detailed fabrication and installation drawings were produced, and initial production cost estimates for the dish were developed. These issues, and the final dish design, are presented in this report. 7 refs., 33 figs., 18 tabs.

  10. Promoting renewable energy technologies

    Grenaa Jensen, S.

    2004-06-01

    Technologies using renewable energy sources are receiving increasing interest from both public authorities and power producing companies, mainly because of the environmental advantages they procure in comparison with conventional energy sources. These technologies can be substitution for conventional energy sources and limit damage to the environment. Furthermore, several of the renewable energy technologies satisfy an increasing political goal of self-sufficiency within energy production. The subject of this thesis is promotion of renewable technologies. The primary goal is to increase understanding on how technological development takes place, and establish a theoretical framework that can assist in the construction of policy strategies including instruments for promotion of renewable energy technologies. Technological development is analysed by through quantitative and qualitative methods. (BA)

  11. Effects of irradiation distance on supply of reactive oxygen species to the bottom of a Petri dish filled with liquid by an atmospheric O{sub 2}/He plasma jet

    Kawasaki, Toshiyuki, E-mail: kawasaki@nbu.ac.jp; Kusumegi, Shota; Kudo, Akihiro; Sakanoshita, Tomohiro; Tsurumaru, Takuya; Sato, Akihiro [Department of Mechanical and Electrical Engineering, Nippon Bunri University, Oita, Oita 870-0397 (Japan); Uchida, Giichiro [Joining and Welding Research Institute, Osaka University, Ibaraki, Osaka 567-0047 (Japan); Koga, Kazunori; Shiratani, Masaharu [Graduate School of Information Science and Electrical Engineering, Kyushu University, Fukuoka, Fukuoka 819-0395 (Japan)

    2016-05-07

    The impact of irradiation distances on plasma jet-induced specific effects on the supply of reactive oxygen species (ROS) to the bottom of a Petri dish filled with liquid was investigated using a KI-starch gel reagent that can be employed as a ROS indicator even in water. O{sub 3} exposure experiments without plasma irradiation were also performed to elucidate the specific effects of the plasma jet. Relative concentrations of ROS transported to the bottom were evaluated using absorbance measurements. The results indicated that ROS supply to the bottom is markedly enhanced by the plasma jet irradiation at shorter irradiation distances, whereas similar results could not be obtained for the O{sub 3} exposure. In these cases, the liquid mixing in the depth direction was also enhanced by the plasma jet irradiation only, and the supply of reactive atomic oxygen to the liquid surface was markedly increased as well.

  12. Laser Technology.

    Gauger, Robert

    1993-01-01

    Describes lasers and indicates that learning about laser technology and creating laser technology activities are among the teacher enhancement processes needed to strengthen technology education. (JOW)

  13. Economic aspects of Solar Thermal Technologies for electricity generation

    Meinecke, W.

    1993-01-01

    Economic results of German studies are presented, which compare the four solar thermal technologies for electricity generation (parabolic trough collector system, central receiver system, parabolic dish/Stirling system, solar chimney plant). These studies were carried out by Interatom (today Siemens/KWU) in Bergisch Gladbach, Flachglas Solartechnik in Koln and Schlaich Bergermann and Partner in Stuggart under contract of DLR in Koln. Funds were made available by the German Ministry of Research and Development (BMFT). The results indicate that all of the investigated technologies have the potential to reduce the generating costs and that in the future costs of below 0.30 DM/kWh could be expected under excellent insolation conditions (e.G. 2850 kWh/m''2 a direct insolation as in California/USA). (Author) 25 refs

  14. United States Department of Energy solar receiver technology development

    Klimas, P. C.; Diver, R. B.; Chavez, J. M.

    The United States Department of Energy (DOE), through Sandia National Laboratories, has been conducting a Solar Thermal Receiver Technology Development Program, which maintains a balance between analytical modeling, bench and small scale testing, and experimentation conducted at scales representative of commercially-sized equipment. Central receiver activities emphasize molten salt-based systems on large scales and volumetric devices in the modeling and small scale testing. These receivers are expected to be utilized in solar power plants rated between 100 and 200 MW. Distributed receiver research focuses on liquid metal refluxing devices. These are intended to mate parabolic dish concentrators with Stirling cycle engines in the 5 to 25 kW(sub e) power range. The effort in the area of volumetric receivers is less intensive and highly cooperative in nature. A ceramic foam absorber of Sandia design was successfully tested on the 200 kW(sub t) test bed at Plataforma Solar during 1989. Material integrity during the approximately 90-test series was excellent. Significant progress has been made with parabolic dish concentrator-mounted receivers using liquid metals (sodium or a potassium/sodium mixture) as heat transport media. Sandia has successfully solar-tested a pool boiling reflux receiver sized to power a 25 kW Stirling engine. Boiling stability and transient operation were both excellent. This document describes these activities in detail and will outline plans for future development.

  15. Moralizing Food Technology

    Coff, Christian Eyde

    2015-01-01

    Food technologies are common on many levels in society and used by both food professionals and consumers. Food technologies are not neutral. They inform and shape the behaviour of people. This paper presents a theoretical framework for analysing the mediating role of food technology and its...... influence on food ethics. Post-phenomenology and the idea of a technologically mediated morality are central theoretical approaches. Four elements are included in the analytical framework: perception, interpretation, intentionality, and mediated morality. The framework is applied to two cases; food safety...

  16. Technology for Boundaries

    Bødker, Susanne; Kristensen, Jannie Friis; Nielsen, Christina

    2003-01-01

    .After analysing the history and the current boundary work, the paper will propose new technological support for boundary work. In particular the paper will suggest means of supporting boundaries when these are productive and for changing boundaries when this seems more appropriate. In total, flexible technologies......This paper presents a study of an organisation, which is undergoing a process transforming organisational and technological boundaries. In particular, we shall look at three kinds of boundaries: the work to maintain and change the boundary between the organisation and its customers; boundaries...... seem a core issue when dealing with technology for boundaries....

  17. Disruptive Technologies in Higher Education

    Flavin, Michael

    2012-01-01

    This paper analyses the role of "disruptive" innovative technologies in higher education. In this country and elsewhere, Higher Education Institutions (HEIs) have invested significant sums in learning technologies, with Virtual Learning Environments (VLEs) being more or less universal, but these technologies have not been universally…

  18. Recriticality analyses for CAPRA cores

    Maschek, W.; Thiem, D.

    1995-01-01

    The first scoping calculation performed show that the energetics levels from recriticalities in CAPRA cores are in the same range as in conventional cores. However, considerable uncertainties exist and further analyses are necessary. Additional investigations are performed for the separation scenarios of fuel/steel/inert and matrix material as a large influence of these processes on possible ramp rates and kinetics parameters was detected in the calculations. (orig./HP)

  19. Recriticality analyses for CAPRA cores

    Maschek, W.; Thiem, D.

    1995-08-01

    The first scoping calculation performed show that the energetics levels from recriticalities in CAPRA cores are in the same range as in conventional cores. However, considerable uncertainties exist and further analyses are necessary. Additional investigations are performed for the separation scenarios of fuel/steel/inert and matrix material as a large influence of these processes on possible ramp rates and kinetics parameters was detected in the calculations. (orig./HP)

  20. Technical center for transportation analyses

    Foley, J.T.

    1978-01-01

    A description is presented of an information search/retrieval/research activity of Sandia Laboratories which provides technical environmental information which may be used in transportation risk analyses, environmental impact statements, development of design and test criteria for packaging of energy materials, and transportation mode research studies. General activities described are: (1) history of center development; (2) environmental information storage/retrieval system; (3) information searches; (4) data needs identification; and (5) field data acquisition system and applications

  1. Methodology of cost benefit analyses

    Patrik, M.; Babic, P.

    2000-10-01

    The report addresses financial aspects of proposed investments and other steps which are intended to contribute to nuclear safety. The aim is to provide introductory insight into the procedures and potential of cost-benefit analyses as a routine guide when making decisions on costly provisions as one of the tools to assess whether a particular provision is reasonable. The topic is applied to the nuclear power sector. (P.A.)

  2. Spatial Analyses of Harappan Urban Settlements

    Hirofumi Teramura

    2006-12-01

    Full Text Available The Harappan Civilization occupies a unique place among the early civilizations of the world with its well planned urban settlements, advanced handicraft and technology, religious and trade activities. Using a Geographical Information Systems (GIS, this study presents spatial analyses that locate urban settlements on a digital elevation model (DEM according to the three phases of early, mature and late. Understanding the relationship between the spatial distribution of Harappan sites and the change in some factors, such as topographic features, river passages or sea level changes, will lead to an understanding of the dynamism of this civilization. It will also afford a glimpse of the factors behind the formation, development, and decline of the Harappan Civilization.

  3. Towards sustainable innovation : analysing and dealing with systemic problems in innovation systems

    Wieczorek, Anna

    2014-01-01

    Technological Innovation System (TIS) perspective became a popular tool to analyse and understand the diffusion of particular, mostly renewable, technologies and their contribution to sustainability transitions. The core of the current TIS studies comprise of the analyses of the emergent structural

  4. Development of an approach for the analysis of network technologies in safety related instrumentation and control systems with respect to the propagation and effect of postulated failures; Entwicklung eines Ansatzes zur Analyse der Netzwerktechnologien in sicherheitsrelevanten Leittechniksystemen hinsichtlich Verbreitung und Auswirkung postulierter Fehler

    Herb, Joachim; Jopen, Manuela; Lindner, Falk; Piljugin, Ewgenij; Vogt, Pascal

    2015-06-15

    So far, safety related instrumentation and control (I and C) functions in nuclear power plants, such as controlling of safety systems, were mostly performed by conventional (analog) I and C equipment. For some years now, I and C systems and equipment in nuclear power plants worldwide, but also in Germany, are modernized by computer-based I and C systems. In signal processing of the computer-based I and C systems, modern network technologies are used both for internal and external communication, whereas the reliability and safety for information transfer and processing plays an important role. National and interna-tional operational experience shows a significant influence of communication in a net-worked I and C system on its reliability. The aim of the GRS within the project 361R01351 ''Development of an approach for an analysis of network technologies in safety related I and C systems in view of distribution and effect of postulated failures'' was to improve the expertise in the field of network communication, to investigate phenomenologically potential sources of failures and fault propagation paths (Network failures) in a generic I and C system as well as to develop methodic approaches for analyses of propagation and effect of postulated failures in typical networks. The GRS conducted extensive research in the field of ''Data communication in digital I and C systems''. In this report, the basic principles of data communication of computer-based I and C systems are presented. This includes, among other things, network topolo-gies, communication protocols and standards as well as generic failures. Additionally, the properties of different analysis methods and its applicability for reliability analyses of network communication in computer-based I and C systems are discussed. Based on state of the art evaluation, an analysis approach was developed, which takes into account the specific properties of network communication and

  5. Chapter No.4. Safety analyses

    2002-01-01

    In 2001 the activity in the field of safety analyses was focused on verification of the safety analyses reports for NPP V-2 Bohunice and NPP Mochovce concerning the new profiled fuel and probabilistic safety assessment study for NPP Mochovce. The calculation safety analyses were performed and expert reviews for the internal UJD needs were elaborated. An important part of work was performed also in solving of scientific and technical tasks appointed within bilateral projects of co-operation between UJD and its international partnership organisations as well as within international projects ordered and financed by the European Commission. All these activities served as an independent support for UJD in its deterministic and probabilistic safety assessment of nuclear installations. A special attention was paid to a review of probabilistic safety assessment study of level 1 for NPP Mochovce. The probabilistic safety analysis of NPP related to the full power operation was elaborated in the study and a contribution of the technical and operational improvements to the risk decreasing was quantified. A core damage frequency of the reactor was calculated and the dominant initiating events and accident sequences with the major contribution to the risk were determined. The target of the review was to determine the acceptance of the sources of input information, assumptions, models, data, analyses and obtained results, so that the probabilistic model could give a real picture of the NPP. The review of the study was performed in co-operation of UJD with the IAEA (IPSART mission) as well as with other external organisations, which were not involved in the elaboration of the reviewed document and probabilistic model of NPP. The review was made in accordance with the IAEA guidelines and methodical documents of UJD and US NRC. In the field of calculation safety analyses the UJD activity was focused on the analysis of an operational event, analyses of the selected accident scenarios

  6. Analysing the Wrongness of Killing

    Di Nucci, Ezio

    2014-01-01

    This article provides an in-depth analysis of the wrongness of killing by comparing different versions of three influential views: the traditional view that killing is always wrong; the liberal view that killing is wrong if and only if the victim does not want to be killed; and Don Marquis‟ future...... of value account of the wrongness of killing. In particular, I illustrate the advantages that a basic version of the liberal view and a basic version of the future of value account have over competing alternatives. Still, ultimately none of the views analysed here are satisfactory; but the different...

  7. Methodological challenges in carbohydrate analyses

    Mary Beth Hall

    2007-07-01

    Full Text Available Carbohydrates can provide up to 80% of the dry matter in animal diets, yet their specific evaluation for research and diet formulation is only now becoming a focus in the animal sciences. Partitioning of dietary carbohydrates for nutritional purposes should reflect differences in digestion and fermentation characteristics and effects on animal performance. Key challenges to designating nutritionally important carbohydrate fractions include classifying the carbohydrates in terms of nutritional characteristics, and selecting analytical methods that describe the desired fraction. The relative lack of information on digestion characteristics of various carbohydrates and their interactions with other fractions in diets means that fractions will not soon be perfectly established. Developing a system of carbohydrate analysis that could be used across animal species could enhance the utility of analyses and amount of data we can obtain on dietary effects of carbohydrates. Based on quantities present in diets and apparent effects on animal performance, some nutritionally important classes of carbohydrates that may be valuable to measure include sugars, starch, fructans, insoluble fiber, and soluble fiber. Essential to selection of methods for these fractions is agreement on precisely what carbohydrates should be included in each. Each of these fractions has analyses that could potentially be used to measure them, but most of the available methods have weaknesses that must be evaluated to see if they are fatal and the assay is unusable, or if the assay still may be made workable. Factors we must consider as we seek to analyze carbohydrates to describe diets: Does the assay accurately measure the desired fraction? Is the assay for research, regulatory, or field use (affects considerations of acceptable costs and throughput? What are acceptable accuracy and variability of measures? Is the assay robust (enhances accuracy of values? For some carbohydrates, we

  8. Responsible technology acceptance

    Toft, Madeleine Broman; Schuitema, Geertje; Thøgersen, John

    2014-01-01

    As a response to climate change and the desire to gain independence from imported fossil fuels, there is a pressure to increase the proportion of electricity from renewable sources which is one of the reasons why electricity grids are currently being turned into Smart Grids. In this paper, we focus...... on private consumers’ acceptance of having Smart Grid technology installed in their home. We analyse acceptance in a combined framework of the Technology Acceptance Model and the Norm Activation Model. We propose that individuals are only likely to accept Smart Grid technology if they assess usefulness...... in terms of a positive impact for society and the environment. Therefore, we expect that Smart Grid technology acceptance can be better explained when the well-known technology acceptance parameters included in the Technology Acceptance Model are supplemented by moral norms as suggested by the Norm...

  9. Severe accident recriticality analyses (SARA)

    Frid, W.; Højerup, C.F.; Lindholm, I.

    2001-01-01

    with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

  10. Hydrogen Analyses in the EPR

    Worapittayaporn, S.; Eyink, J.; Movahed, M.

    2008-01-01

    In severe accidents with core melting large amounts of hydrogen may be released into the containment. The EPR provides a combustible gas control system to prevent hydrogen combustion modes with the potential to challenge the containment integrity due to excessive pressure and temperature loads. This paper outlines the approach for the verification of the effectiveness and efficiency of this system. Specifically, the justification is a multi-step approach. It involves the deployment of integral codes, lumped parameter containment codes and CFD codes and the use of the sigma criterion, which provides the link to the broad experimental data base for flame acceleration (FA) and deflagration to detonation transition (DDT). The procedure is illustrated with an example. The performed analyses show that hydrogen combustion at any time does not lead to pressure or temperature loads that threaten the containment integrity of the EPR. (authors)

  11. Uncertainty and Sensitivity Analyses Plan

    Simpson, J.C.; Ramsdell, J.V. Jr.

    1993-04-01

    Hanford Environmental Dose Reconstruction (HEDR) Project staff are developing mathematical models to be used to estimate the radiation dose that individuals may have received as a result of emissions since 1944 from the US Department of Energy's (DOE) Hanford Site near Richland, Washington. An uncertainty and sensitivity analyses plan is essential to understand and interpret the predictions from these mathematical models. This is especially true in the case of the HEDR models where the values of many parameters are unknown. This plan gives a thorough documentation of the uncertainty and hierarchical sensitivity analysis methods recommended for use on all HEDR mathematical models. The documentation includes both technical definitions and examples. In addition, an extensive demonstration of the uncertainty and sensitivity analysis process is provided using actual results from the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC). This demonstration shows how the approaches used in the recommended plan can be adapted for all dose predictions in the HEDR Project

  12. The hemispherical deflector analyser revisited

    Benis, E.P. [Institute of Electronic Structure and Laser, P.O. Box 1385, 71110 Heraklion, Crete (Greece)], E-mail: benis@iesl.forth.gr; Zouros, T.J.M. [Institute of Electronic Structure and Laser, P.O. Box 1385, 71110 Heraklion, Crete (Greece); Department of Physics, University of Crete, P.O. Box 2208, 71003 Heraklion, Crete (Greece)

    2008-04-15

    Using the basic spectrometer trajectory equation for motion in an ideal 1/r potential derived in Eq. (101) of part I [T.J.M. Zouros, E.P. Benis, J. Electron Spectrosc. Relat. Phenom. 125 (2002) 221], the operational characteristics of a hemispherical deflector analyser (HDA) such as dispersion, energy resolution, energy calibration, input lens magnification and energy acceptance window are investigated from first principles. These characteristics are studied as a function of the entry point R{sub 0} and the nominal value of the potential V(R{sub 0}) at entry. Electron-optics simulations and actual laboratory measurements are compared to our theoretical results for an ideal biased paracentric HDA using a four-element zoom lens and a two-dimensional position sensitive detector (2D-PSD). These results should be of particular interest to users of modern HDAs utilizing a PSD.

  13. The hemispherical deflector analyser revisited

    Benis, E.P.; Zouros, T.J.M.

    2008-01-01

    Using the basic spectrometer trajectory equation for motion in an ideal 1/r potential derived in Eq. (101) of part I [T.J.M. Zouros, E.P. Benis, J. Electron Spectrosc. Relat. Phenom. 125 (2002) 221], the operational characteristics of a hemispherical deflector analyser (HDA) such as dispersion, energy resolution, energy calibration, input lens magnification and energy acceptance window are investigated from first principles. These characteristics are studied as a function of the entry point R 0 and the nominal value of the potential V(R 0 ) at entry. Electron-optics simulations and actual laboratory measurements are compared to our theoretical results for an ideal biased paracentric HDA using a four-element zoom lens and a two-dimensional position sensitive detector (2D-PSD). These results should be of particular interest to users of modern HDAs utilizing a PSD

  14. Analysing Protocol Stacks for Services

    Gao, Han; Nielson, Flemming; Nielson, Hanne Riis

    2011-01-01

    We show an approach, CaPiTo, to model service-oriented applications using process algebras such that, on the one hand, we can achieve a certain level of abstraction without being overwhelmed by the underlying implementation details and, on the other hand, we respect the concrete industrial...... standards used for implementing the service-oriented applications. By doing so, we will be able to not only reason about applications at different levels of abstractions, but also to build a bridge between the views of researchers on formal methods and developers in industry. We apply our approach...... to the financial case study taken from Chapter 0-3. Finally, we develop a static analysis to analyse the security properties as they emerge at the level of concrete industrial protocols....

  15. Analysing performance through value creation

    Adrian TRIFAN

    2015-12-01

    Full Text Available This paper draws a parallel between measuring financial performance in 2 variants: the first one using data offered by accounting, which lays emphasis on maximizing profit, and the second one which aims to create value. The traditional approach to performance is based on some indicators from accounting data: ROI, ROE, EPS. The traditional management, based on analysing the data from accounting, has shown its limits, and a new approach is needed, based on creating value. The evaluation of value based performance tries to avoid the errors due to accounting data, by using other specific indicators: EVA, MVA, TSR, CVA. The main objective is shifted from maximizing the income to maximizing the value created for shareholders. The theoretical part is accompanied by a practical analysis regarding the creation of value and an analysis of the main indicators which evaluate this concept.

  16. Focus on Technologies: Worry or Technology?

    Saulius Kanišauskas

    2015-10-01

    Full Text Available The paper analyses different attitudes towards technologies in contemporary philosophical discourses. It points out that classical notion of technology formulated by Martin Heidegger seems to be more and more often questioned and even forgotten. As a result, it is being replaced by the theory of determinism, according to which the change of technologies determines the changes in social systems, the human being including. This happens this way and not vice versa. Nowadays technē, or “technika” (in English: technology is mostly understood in the instrumental meaning or in the meaning of power. It is considered to be a powerful means, tool or mechanism to influence, change, control and manipulate human consciousness and human feelings. Despite the fact that technologies have already been tamed, the problem of huge responsibility for using and developing them arises. It is questioned whether the increasing society’s attention to modern technologies is not a particular “technology” of the postmodern capitalism to manipulate social consciousness. In parallel with “yes” answer to this question, Albert Borgmann’s idea that the causes of technological development have an ontological dimension, i.e. the causes are rooted in the nature of human beings themselves and their desire to adore own creativity, is discussed. Thus, it becomes necessary to probe deeper into the nature of creativity.

  17. Sport Technology

    Kirkbride, T

    2007-11-01

    Full Text Available Technology is transforming the games themselves and at times with dire consequences. Tony Kirkbride, Head: CSIR Technology Centre said there are a variety of sports technologies and there have been advances in material sciences and advances...

  18. Assistive Technology

    ... Page Resize Text Printer Friendly Online Chat Assistive Technology Assistive technology (AT) is any service or tool that helps ... be difficult or impossible. For older adults, such technology may be a walker to improve mobility or ...

  19. Interpretation of Internet technology

    Madsen, Charlotte Øland

    2001-01-01

    Research scope: The topic of the research project is to investigate how new internet technologies such as e-trade and customer relation marketing and management are implemented in Danish food processing companies. The aim is to use Weick's (1995) sensemaking concept to analyse the strategic...... processes leading to the use of internet marketing technologies and to investigate how these new technologies are interpreted into the organisation. Investigating the organisational socio-cognitive processes underlying the decision making processes will give further insight into the socio...

  20. Proteins analysed as virtual knots

    Alexander, Keith; Taylor, Alexander J.; Dennis, Mark R.

    2017-02-01

    Long, flexible physical filaments are naturally tangled and knotted, from macroscopic string down to long-chain molecules. The existence of knotting in a filament naturally affects its configuration and properties, and may be very stable or disappear rapidly under manipulation and interaction. Knotting has been previously identified in protein backbone chains, for which these mechanical constraints are of fundamental importance to their molecular functionality, despite their being open curves in which the knots are not mathematically well defined; knotting can only be identified by closing the termini of the chain somehow. We introduce a new method for resolving knotting in open curves using virtual knots, which are a wider class of topological objects that do not require a classical closure and so naturally capture the topological ambiguity inherent in open curves. We describe the results of analysing proteins in the Protein Data Bank by this new scheme, recovering and extending previous knotting results, and identifying topological interest in some new cases. The statistics of virtual knots in protein chains are compared with those of open random walks and Hamiltonian subchains on cubic lattices, identifying a regime of open curves in which the virtual knotting description is likely to be important.

  1. Digital image analyser for autoradiography

    Muth, R.A.; Plotnick, J.

    1985-01-01

    The most critical parameter in quantitative autoradiography for assay of tissue concentrations of tracers is the ability to obtain precise and accurate measurements of optical density of the images. Existing high precision systems for image analysis, rotating drum densitometers, are expensive, suffer from mechanical problems and are slow. More moderately priced and reliable video camera based systems are available, but their outputs generally do not have the uniformity and stability necessary for high resolution quantitative autoradiography. The authors have designed and constructed an image analyser optimized for quantitative single and multiple tracer autoradiography which the authors refer to as a memory-mapped charged-coupled device scanner (MM-CCD). The input is from a linear array of CCD's which is used to optically scan the autoradiograph. Images are digitized into 512 x 512 picture elements with 256 gray levels and the data is stored in buffer video memory in less than two seconds. Images can then be transferred to RAM memory by direct memory-mapping for further processing. Arterial blood curve data and optical density-calibrated standards data can be entered and the optical density images can be converted automatically to tracer concentration or functional images. In double tracer studies, images produced from both exposures can be stored and processed in RAM to yield ''pure'' individual tracer concentration or functional images. Any processed image can be transmitted back to the buffer memory to be viewed on a monitor and processed for region of interest analysis

  2. Nano technology

    Lee, In Sik

    2002-03-01

    This book is introduction of nano technology, which describes what nano technology is, alpha and omega of nano technology, the future of Korean nano technology and human being's future and nano technology. The contents of this book are nano period is coming, a engine of creation, what is molecular engineering, a huge nano technology, technique on making small things, nano materials with exorbitant possibility, the key of nano world the most desirable nano technology in bio industry, nano development plan of government, the direction of development for nano technology and children of heart.

  3. Rover Technologies

    National Aeronautics and Space Administration — Develop and mature rover technologies supporting robotic exploration including rover design, controlling rovers over time delay and for exploring . Technology...

  4. Making technology public

    Winthereik, Brit Ross; Johannsen, Nis; Strand, Dixi Louise

    2008-01-01

    the transformative potential of the portal presentation for reconfiguring relationships between citizens, health care systems, and information and communication technology (ICT). The analysis is guided by Haraway's notion of diffraction. Findings – The analysis demonstrates the particular way in which the user...... secure the future of the technology and organisation behind it. Research limitations/implications – The paper extends the script metaphor beyond a limited designer-technology-user configuration and argues that scripts in the paraphernalia of technologies also can and should be “de......Purpose – Through an analysis of a demonstration video presenting a new national e-health portal, this paper aims to explore the assumptions and limitations of the concept of “script” and suggests a different approach to analysing the moral order of technology design. Design...

  5. Technologies in organic farming

    Lassen, Jesper

    2015-01-01

    the nutrient gap by recycling sewage sludge, and in particular the criteria applied when these technologies are assessed, are analysed. This part of the analysis shows how organic consumers base their assessment of alternative strategies and technologies primarily on concerns about environmental risks...... to phase out their use of conventional manure before 2021. This, however, raises a number of questions about consumers’ acceptance of the alternative technologies that have been proposed to close the nutrient gap. Drawing on qualitative interviews with Danish organic consumers, this paper first discusses...... what, from a consumers perspective, characterizes the technologies consumers associate with organic production. This part of the analysis shows that by and large consumers regard organic technologies as the opposite of conventional farming. Second, consumers’ perceptions of solutions suggested to close...

  6. Technical analysis of a 400 W{sub p} solar Stirling plant; Technische Analyse einer 400 W{sub p} Solar-Stirling-Anlage

    Mueller, Reinhard; Rackwitz, Axel [Hochschule fuer Technik, Wirtschaft und Kultur Leipzig (HTWK), Markkleeberg (DE). Fakultaet Maschinenbau und Energietechnik (Montenegro)

    2012-07-01

    It is advisable to analyse different alternatives of the generation and supply of electrical energy and thermoelectricity with renewable forms of energy, because the demand of fuels (e.g. coal and oil) and the energy costs rise continuously. Technical optimization and cost-effectiveness of the different alternatives are the most important points of tests. This was the reason why at the Department of Mechanical and Energy Engineering of the Leipzig University of Applied Science a test ground ''renewable forms of energy'' has been built up step by step for thirteen years including two photovoltaic systems with different tracking systems, two wind-mills, an air-water-heat-pump and a dish-stirling-system. (orig.)

  7. Severe Accident Recriticality Analyses (SARA)

    Frid, W. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Hoejerup, F. [Risoe National Lab. (Denmark); Lindholm, I.; Miettinen, J.; Puska, E.K. [VTT Energy, Helsinki (Finland); Nilsson, Lars [Studsvik Eco and Safety AB, Nykoeping (Sweden); Sjoevall, H. [Teoliisuuden Voima Oy (Finland)

    1999-11-01

    Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B{sub 4}C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

  8. Severe accident recriticality analyses (SARA)

    Frid, W. E-mail: wiktor.frid@ski.se; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H

    2001-11-01

    Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s{sup -1} injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g{sup -1}, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s{sup -1}. In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated

  9. Severe accident recriticality analyses (SARA)

    Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H.

    2001-01-01

    Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s -1 injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g -1 , was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s -1 . In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated quasi steady

  10. Severe Accident Recriticality Analyses (SARA)

    Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Puska, E.K.; Nilsson, Lars; Sjoevall, H.

    1999-11-01

    Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B 4 C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

  11. Science and technology policy

    Who is responsible for environmental and technological policy in Denmark? And how are those "policy-makers" made accountable to the public for their decisions?   This report attempts to answer these important questions by presenting the Danish contribution to the EU-funded project, Analysing Public...

  12. Technology programme

    2007-01-01

    The technology activities carried out by the EURATOM-ENEA Association concern the continuation of the European Fusion Development Agreement (EFDA) as well as the ITER activities coordinated by the ITER International Office and Fusion for Energy. Also included in the activities are design and RD under the Broader Approach Agreement between the EU and Japan. In order to better contribute to the programme a number of consortium agreements among the Associations are being signed. Collaboration with industries in view of their participation in the construction of ITER was further strengthened, mainly in the field of magnet and divertor components. The new European Test Blanket Facility at ENEA Brasimone was completed; the design of the ITER radial neutron camera was optimised and the performance achievable with the in-vessel viewing system was further assessed by experimental trials. Design activities for the JT-60SA magnet and power supply system as well as the design and experimental activities related to the target of the International Fusion Materials Irradiation Facility were continued. Significant work was done to define quality assurance for neutronics analyses. Mockups of the ITER pre-compression ring made in glass fibre epoxy were tested. The activities and results documented in the following illustrate ENEA's efforts to support fusion development

  13. Statistical analyses of extreme food habits

    Breuninger, M.; Neuhaeuser-Berthold, M.

    2000-01-01

    This report is a summary of the results of the project ''Statistical analyses of extreme food habits'', which was ordered from the National Office for Radiation Protection as a contribution to the amendment of the ''General Administrative Regulation to paragraph 45 of the Decree on Radiation Protection: determination of the radiation exposition by emission of radioactive substances from facilities of nuclear technology''. Its aim is to show if the calculation of the radiation ingested by 95% of the population by food intake, like it is planned in a provisional draft, overestimates the true exposure. If such an overestimation exists, the dimension of it should be determined. It was possible to prove the existence of this overestimation but its dimension could only roughly be estimated. To identify the real extent of it, it is necessary to include the specific activities of the nuclides, which were not available for this investigation. In addition to this the report shows how the amounts of food consumption of different groups of foods influence each other and which connections between these amounts should be taken into account, in order to estimate the radiation exposition as precise as possible. (orig.) [de

  14. Electronic technology

    Kim, Jin Su

    2010-07-01

    This book is composed of five chapters, which introduces electronic technology about understanding of electronic, electronic component, radio, electronic application, communication technology, semiconductor on its basic, free electron and hole, intrinsic semiconductor and semiconductor element, Diode such as PN junction diode, characteristic of junction diode, rectifier circuit and smoothing circuit, transistor on structure of transistor, characteristic of transistor and common emitter circuit, electronic application about electronic equipment, communication technology and education, robot technology and high electronic technology.

  15. Pawnee Nation Energy Option Analyses

    Matlock, M.; Kersey, K.; Riding In, C.

    2009-07-21

    Pawnee Nation of Oklahoma Energy Option Analyses In 2003, the Pawnee Nation leadership identified the need for the tribe to comprehensively address its energy issues. During a strategic energy planning workshop a general framework was laid out and the Pawnee Nation Energy Task Force was created to work toward further development of the tribe’s energy vision. The overarching goals of the “first steps” project were to identify the most appropriate focus for its strategic energy initiatives going forward, and to provide information necessary to take the next steps in pursuit of the “best fit” energy options. Description of Activities Performed The research team reviewed existing data pertaining to the availability of biomass (focusing on woody biomass, agricultural biomass/bio-energy crops, and methane capture), solar, wind and hydropower resources on the Pawnee-owned lands. Using these data, combined with assumptions about costs and revenue streams, the research team performed preliminary feasibility assessments for each resource category. The research team also reviewed available funding resources and made recommendations to Pawnee Nation highlighting those resources with the greatest potential for financially-viable development, both in the near-term and over a longer time horizon. Findings and Recommendations Due to a lack of financial incentives for renewable energy, particularly at the state level, combined mediocre renewable energy resources, renewable energy development opportunities are limited for Pawnee Nation. However, near-term potential exists for development of solar hot water at the gym, and an exterior wood-fired boiler system at the tribe’s main administrative building. Pawnee Nation should also explore options for developing LFGTE resources in collaboration with the City of Pawnee. Significant potential may also exist for development of bio-energy resources within the next decade. Pawnee Nation representatives should closely monitor

  16. Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

    Jantzen, Carol M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, David M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Guenther, Chris P. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Shekhawat, Dushyant [National Energy Technology Lab. (NETL), Morgantown, WV (United States); VanEssendelft, Dirk T. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Means, Nicholas C. [AECOM Technology Corp., Oak Ridge, TN (United States)

    2015-04-23

    in process piping and materials, in excessive off-gas absorbent loading, and in undesired process emissions. The ash content of the coal is important as the ash adds to the DMR and other vessel products which affect the final waste product mass and composition. The amount and composition of the ash also affects the reaction kinetics. Thus ash content and composition contributes to the mass balance. In addition, sodium, potassium, calcium, sulfur, and maybe silica and alumina in the ash may contribute to wall-scale formation. Sodium, potassium, and alumina in the ash will be overwhelmed by the sodium, potassium, and alumina from the feed but the impact from the other ash components needs to be quantified. A maximum coal particle size is specified so the feed system does not plug and a minimum particle size is specified to prevent excess elutriation from the DMR to the Process Gas Filter (PGF). A vendor specification was used to procure the calcined coal for IWTU processing. While the vendor supplied a composite analysis for the 22 tons of coal (Appendix A), this study compares independent analyses of the coal performed at the Savannah River National Laboratory (SRNL) and at the National Energy Technology Laboratory (NETL). Three supersacks a were sampled at three different heights within the sack in order to determine within bag variability and between bag variability of the coal. These analyses were also compared to the vendor’s composite analyses and to the coal specification. These analyses were also compared to historic data on Bestac coal analyses that had been performed at Hazen Research Inc. (HRI) between 2004-2011.

  17. In the Presence of Technology

    Nortvig, Anne-Mette

    2013-01-01

    Abstract: In a hybrid synchronous classroom that includes both on line and on campus students, technology plays a big part in the teaching. This paper attempts to analyse and discuss how the transparency of technology affects opportunities for the students to interact and for the teacher to be pr...

  18. Health Educational Potentials of Technologies.

    Magnussen, Rikke; Aagaard-Hansen, Jens

    2012-01-01

    The field of health promotion technology has been in an exponential growth in recent years and smart phone applications, exer-games and self-monitoring devices has become part of fitness activities and health education. In this work-in-progress-paper theoretical perspectives for categorising and analysing health educational potentials of technologies are presented.

  19. The necessity for comparative risk analyses as seen from the political point of view

    Steger, U.

    1981-01-01

    The author describes the current insufficient utilization of risk analyses in the political decision process and investigates if other technologies encounter the same difficulties of acceptance as in the nuclear energy field. This being likely he is trying to find out which contribution comparative risk analyses could make to the process of democratic will-formation so that new technologies are accepted. Firstly the author establishes theses criticizing the recent scientific efforts made in the field of risk analyses and their usability for the political decision process. He then defines the criteria risk analyses have to meet in order to serve as scientific elements for consultative political discussions. (orig./HP) [de

  20. APPLYING SPECTROSCOPIC METHODS ON ANALYSES OF HAZARDOUS WASTE

    Dobrinić, Julijan; Kunić, Marija; Ciganj, Zlatko

    2000-01-01

    Abstract The paper presents results of measuring the content of heavy and other metals in waste samples from the hazardous waste disposal site of Sovjak near Rijeka. The preliminary design elaboration and the choice of the waste disposal sanification technology were preceded by the sampling and physico-chemical analyses of disposed waste, enabling its categorization. The following spectroscopic methods were applied on metal content analysis: Atomic absorption spectroscopy (AAS) and plas...

  1. Why to use mobile technology?

    Bolat, Elvira

    2014-01-01

    No holistic portrayal exists to map and discuss values deriving from mobile technology use. This empirical paper addresses this gap. To address research purpose adapted grounded theory approach is applied to collect and analyse in-depth interviews with twenty-eight SME managers. This study concludes that mobile technology represents novel and unique category of technology. Whether MT is a simple mean to advanced communication with no physical boundaries of time and location or a business tool...

  2. Structural analyses of ITER toroidal field coils under fault conditions

    Jong, C.T.J.

    1992-04-01

    ITER (International Thermonuclear Experimental Reactor) is intended to be an experimental thermonuclear tokamak reactor testing the basic physics performance and technologies essential to future fusion reactors. The magnet system of ITER consists essentially of 4 sub-systems, i.e. toroidal field coils (TFCs), poloidal field coils (PFCs), power supplies, and cryogenic supplies. These subsystems do not contain significant radioactivity inventories, but the large energy inventory is a potential accident initiator. The aim of the structural analyses is to prevent accidents from propagating into vacuum vessel, tritium system and cooling system, which all contain significant amounts of radioactivity. As part of design process 3 conditions are defined for PF and TF coils, at which mechanical behaviour has to be analyzed in some detail, viz: normal operating conditions, upset conditions and fault conditions. This paper describes the work carried out by ECN to create a detailed finite element model of 16 TFCs as well as results of some fault condition analyses made with the model. Due to fault conditions, either electrical or mechanical, magnetic loading of TFCs becomes abnormal and further mechanical failure of parts of the overall structure might occur (e.g. failure of coil, gravitational supports, intercoil structure). The analyses performed consist of linear elastic stress analyses and electro-magneto-structural analyses (coupled field analyses). 8 refs.; 5 figs.; 5 tabs

  3. Scanning electron microscopy and micro-analyses

    Brisset, F.; Repoux, L.; Ruste, J.; Grillon, F.; Robaut, F.

    2008-01-01

    Scanning electron microscopy (SEM) and the related micro-analyses are involved in extremely various domains, from the academic environments to the industrial ones. The overall theoretical bases, the main technical characteristics, and some complements of information about practical usage and maintenance are developed in this book. high-vacuum and controlled-vacuum electron microscopes are thoroughly presented, as well as the last generation of EDS (energy dispersive spectrometer) and WDS (wavelength dispersive spectrometer) micro-analysers. Beside these main topics, other analysis or observation techniques are approached, such as EBSD (electron backscattering diffraction), 3-D imaging, FIB (focussed ion beams), Monte-Carlo simulations, in-situ tests etc.. This book, in French language, is the only one which treats of this subject in such an exhaustive way. It represents the actualized and totally updated version of a previous edition of 1979. It gathers the lectures given in 2006 at the summer school of Saint Martin d'Heres (France). Content: 1 - electron-matter interactions; 2 - characteristic X-radiation, Bremsstrahlung; 3 - electron guns in SEM; 4 - elements of electronic optics; 5 - vacuum techniques; 6 - detectors used in SEM; 7 - image formation and optimization in SEM; 7a - SEM practical instructions for use; 8 - controlled pressure microscopy; 8a - applications; 9 - energy selection X-spectrometers (energy dispersive spectrometers - EDS); 9a - EDS analysis; 9b - X-EDS mapping; 10 - technological aspects of WDS; 11 - processing of EDS and WDS spectra; 12 - X-microanalysis quantifying methods; 12a - quantitative WDS microanalysis of very light elements; 13 - statistics: precision and detection limits in microanalysis; 14 - analysis of stratified samples; 15 - crystallography applied to EBSD; 16 - EBSD: history, principle and applications; 16a - EBSD analysis; 17 - Monte Carlo simulation; 18 - insulating samples in SEM and X-ray microanalysis; 18a - insulating

  4. Disruptive technologies in higher education

    Michael Flavin

    2012-08-01

    Full Text Available This paper analyses the role of “disruptive” innovative technologies in higher education. In this country and elsewhere, Higher Education Institutions (HEIs have invested significant sums in learning technologies, with Virtual Learning Environments (VLEs being more or less universal, but these technologies have not been universally adopted and used by students and staff. Instead, other technologies not owned or controlled by HEIs are widely used to support learning and teaching. According to Christensen's theory of Disruptive Innovation, these disruptive technologies are not designed explicitly to support learning and teaching in higher education, but have educational potential. This study uses Activity Theory and Expansive Learning to analyse data regarding the impact of disruptive technologies. The data were obtained through a questionnaire survey about awareness and use of technologies, and through observation and interviews, exploring participants’ actual practice. The survey answers tended to endorse Disruptive Innovation theory, with participants establishing meanings for technologies through their use of them, rather than in keeping with a designer's intentions. Observation revealed that learners use a narrow range of technologies to support learning, but with a tendency to use resources other than those supplied by their HEIs. Interviews showed that participants use simple and convenient technologies to support their learning and teaching. This study identifies a contradiction between learning technologies made available by HEIs, and technologies used in practice. There is no evidence to suggest that a wide range of technologies is being used to support learning and teaching. Instead, a small range of technologies is being used for a wide range of tasks. Students and lecturers are not dependent on their HEIs to support learning and teaching. Instead, they self-select technologies, with use weighted towards established brands. The

  5. 2008 Solar Technologies Market Report

    Price, S.; Margolis, R.; Barbose, G.; Bartlett, J.; Cory, K.; Couture, T.; DeCesaro, J.; Denholm, P.; Drury, E.; Frickel, M.; Hemmeline, C.; Mendelsohn, T.; Ong, S.; Pak, A.; Poole, L.; Peterman, C.; Schwabe, P.; Soni, A.; Speer, B.; Wiser, R.; Zuboy, J.; James, T.

    2010-01-01

    The focus of this report is the U.S. solar electricity market, including photovoltaic (PV) and concentrating solar power (CSP) technologies. The report is organized into five chapters. Chapter 1 provides an overview of global and U.S. installation trends. Chapter 2 presents production and shipment data, material and supply chain issues, and solar industry employment trends. Chapter 3 presents cost, price, and performance trends. Chapter 4 discusses policy and market drivers such as recently passed federal legislation, state and local policies, and developments in project financing. Chapter 5 provides data on private investment trends and near-term market forecasts. Highlights of this report include: (1) The global PV industry has seen impressive growth rates in cell/module production during the past decade, with a 10-year compound annual growth rate (CAGR) of 46% and a 5-year CAGR of 56% through 2008. (2) Thin-film PV technologies have grown faster than crystalline silicon over the past 5 years, with a 10-year CAGR of 47% and a 5-year CAGR of 87% for thin-film shipments through 2008. (3) Global installed PV capacity increased by 6.0 GW in 2008, a 152% increase over 2.4 GW installed in 2007. (4) The United States installed 0.34 GW of PV capacity in 2008, a 63% increase over 0.21 GW in 2007. (5) Global average PV module prices dropped 23% from $4.75/W in 1998 to $3.65/W in 2008. (6) Federal legislation, including the Emergency Economic Stabilization Act of 2008 (EESA, October 2008) and the American Recovery and Reinvestment Act (ARRA, February 2009), is providing unprecedented levels of support for the U.S. solar industry. (7) In 2008, global private-sector investment in solar energy technology topped $16 billion, including almost $4 billion invested in the United States. (8) Solar PV market forecasts made in early 2009 anticipate global PV production and demand to increase fourfold between 2008 and 2012, reaching roughly 20 GW of production and demand by 2012. (9

  6. Improving word coverage using unsupervised morphological analyser

    To enable a computer to process information in human languages, ... vised morphological analyser (UMA) would learn how to analyse a language just by looking ... result for English, but they did remarkably worse for Finnish and Turkish.

  7. Techniques for Analysing Problems in Engineering Projects

    Thorsteinsson, Uffe

    1998-01-01

    Description of how CPM network can be used for analysing complex problems in engineering projects.......Description of how CPM network can be used for analysing complex problems in engineering projects....

  8. Casting Technology.

    Wright, Michael D.; And Others

    1992-01-01

    Three articles discuss (1) casting technology as it relates to industry, with comparisons of shell casting, shell molding, and die casting; (2) evaporative pattern casting for metals; and (3) high technological casting with silicone rubber. (JOW)

  9. Living Technology

    2010-01-01

    This book is aimed at anyone who is interested in learning more about living technology, whether coming from business, the government, policy centers, academia, or anywhere else. Its purpose is to help people to learn what living technology is, what it might develop into, and how it might impact...... our lives. The phrase 'living technology' was coined to refer to technology that is alive as well as technology that is useful because it shares the fundamental properties of living systems. In particular, the invention of this phrase was called for to describe the trend of our technology becoming...... increasingly life-like or literally alive. Still, the phrase has different interpretations depending on how one views what life is. This book presents nineteen perspectives on living technology. Taken together, the interviews convey the collective wisdom on living technology's power and promise, as well as its...

  10. Technology transfer

    1998-01-01

    On the base of technological opportunities and of the environmental target of the various sectors of energy system this paper intend to conjugate the opportunity/objective with economic and social development through technology transfer and information dissemination [it

  11. Some failure analyses of South African Air Force aircraft engine and airframe components

    Benson, JM

    1998-06-01

    Full Text Available Failure analyses of various engine and airframe components from South African Air Force aircraft have been performed by the Division of Materials Science and Technology over several years and these have ranged from crash investigations to minor...

  12. Automatic incrementalization of Prolog based static analyses

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic prog...

  13. Earthing Technology

    Blok, Vincent

    2017-01-01

    In this article, we reflect on the conditions under which new technologies emerge in the Anthropocene and raise the question of how to conceptualize sustainable technologies therein. To this end, we explore an eco-centric approach to technology development, called biomimicry. We discuss opposing

  14. Technology Tiers

    Karlsson, Christer

    2015-01-01

    A technology tier is a level in a product system: final product, system, subsystem, component, or part. As a concept, it contrasts traditional “vertical” special technologies (for example, mechanics and electronics) and focuses “horizontal” feature technologies such as product characteristics...

  15. Sensemaking technologies

    Madsen, Charlotte Øland

    Research scope: The scope of the project is to study technological implementation processes by using Weick's sensemaking concept (Weick, 1995). The purpose of using a social constructivist approach to investigate technological implementation processes is to find out how new technologies transform......, Orlikowski 2000). Viewing the use of technology as a process of enactment opens up for investigating the social processes of interpreting new technology into the organisation (Orlikowski 2000). The scope of the PhD project will therefore be to gain a deeper understanding of how the enactment of new...... & Brass, 1990; Kling 1991; Orlikowski 2000). It also demonstrates that technology is a flexible variable adapted to the organisation's needs, culture, climate and management philosophy, thus leading to different uses and outcomes of the same technology in different organisations (Barley 1986; 1990...

  16. Technology roadmaps

    Pearson, B. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy Technology Centre

    2003-07-01

    The purpose of a technology road map is to define the state of a current technology, relevant market issues, and future market needs; to develop a plan that industry can follow to provide these new products and services; and to map technology pathways and performance goals for bringing these products and services to market. The three stages (planning, implementation, and reviewing and updating), benefits, and status of the Clean Coal Technology Roadmap are outlined. Action Plan 2000, a $1.7 million 2000 Climate Change Technology and Innovation Program, which uses the technology roadmapping process, is described. The members of the management steering committee for the Clean Coal Technology Roadmap are listed. A flowsheet showing activities until November 2004, when the final clean coal road map is due, is included.

  17. Dish/stirling hybrid-receiver

    Mehos, Mark S.; Anselmo, Kenneth M.; Moreno, James B.; Andraka, Charles E.; Rawlinson, K. Scott; Corey, John; Bohn, Mark S.

    2002-01-01

    A hybrid high-temperature solar receiver is provided which comprises a solar heat-pipe-receiver including a front dome having a solar absorber surface for receiving concentrated solar energy, a heat pipe wick, a rear dome, a sidewall joining the front and the rear dome, and a vapor and a return liquid tube connecting to an engine, and a fossil fuel fired combustion system in radial integration with the sidewall for simultaneous operation with the solar heat pipe receiver, the combustion system comprising an air and fuel pre-mixer, an outer cooling jacket for tangentially introducing and cooling the mixture, a recuperator for preheating the mixture, a burner plenum having an inner and an outer wall, a porous cylindrical metal matrix burner firing radially inward facing a sodium vapor sink, the mixture ignited downstream of the matrix forming combustion products, an exhaust plenum, a fossil-fuel heat-input surface having an outer surface covered with a pin-fin array, the combustion products flowing through the array to give up additional heat to the receiver, and an inner surface covered with an extension of the heat-pipe wick, a pin-fin shroud sealed to the burner and exhaust plenums, an end seal, a flue-gas diversion tube and a flue-gas valve for use at off-design conditions to limit the temperature of the pre-heated air and fuel mixture, preventing pre-ignition.

  18. Design rules against buckling of dished heads

    Roche, R.L.; Alix, M.; Autrusson, B.

    1984-01-01

    The aim of this paper is to present the validation of the rules of the French code of presure vessels CODAP. First, it is shown that the theories of buckling cannot give alone a sufficient base of validation and that the experimental justification is necessary. Then, the admissible pressure values corresponding to the CODAP formules are compared with the experimental results. This comparison furnishes the safety margins given by the CODAP formules. Finally, buckling tests of torispherical shells carried out at the CEA Saclay (France) are presented. The results obtained can be represented by a simple semi-empiric formula [fr

  19. Dishing the dirt: Gossiping in organizations

    Clegg, S.R.; van Iterson, A

    2009-01-01

    In an exercise in social theory, rather than an empirical investigation, we concentrate on the role of gossip - spreading 'news about the affairs of another' - in relation to the dynamics of power in organizations. Gossip has often been seen in functional terms, as both positive and negative for the

  20. The dish on the Solar Decathlon

    Meehan, Chris

    2011-07-01

    Within only one week, 19 collegiate teams had to build their technically-advanced, solar-powered, energy-efficient houses to wow judges and the public at this year's US Department of Energy's (DOE's) Solar Decathlon. The unassembled homes began arriving at the West Potomac Park of the National Mall in Washington, DC, at 11 p.m. on September 13. From then on it was a marathon to finish construction and compete in gauntlet of 10 events to test the designs. (orig.)

  1. Proceedings of the 8. Banska Stiavnica Days 2006. Measurements and analyses in environmental sciences and radioenvironmental sciences. Medium-term perspectives of energetic development in the Slovak Republic and in the European Union. Application of nuclear technologies; Zbornik 8. Banskostiavnicke dni 2006. Merania a analyzy v environmentalistike a radioenvironmentalistike. Strednedobe perspektivy rozvoja energetiky v SR a EU. Aplikacie nuklearnych technologii

    Lalik, V; Hybler, P; Schwarz, M [Katedra environmentalneho inzinierstva, Fakulta ekologie a environmentalistiky, Technicka univerzita Zvolen, Banska Stiavnica (Slovakia)

    2006-12-15

    Scientific conference deals with problems in environmental sciences and radio-environmental sciences. The conference proceeded in two sections: (A) Nuclear technologies; (B) Environmental engineering. Forty participants and further fifty guests took part in conference. Twenty-seven lectures and four posters were presented. Proceedings contain fifteen papers from which 8 papers deal with the scope of INIS.

  2. The development of information technologies

    Kostúr Karol

    2002-12-01

    Full Text Available The contribution analyses the tasks information technologies in industry. At present time is the problem of connecting mutual variously levels of management. Therefore, first priority is an integration of information technologies. The information technologies for enterprise management are analysed. The product SAP R/3 appears as suitable for top management. The SAP R/3 Enterprise has a new technology so call web-server. This server enables the integration with e-business. The development my SAP is based on application of Business information warehouse (BW and Strategic enterprise management (SEM. The cheaper products (SPIN + EVIS are characterized too. Whitness Miner is very interesting system. The contribution this technology is programming realization of method KDD – knowledge discovery in databases.

  3. Technology transfer and catch-up; Lessons from the commercial aircraft industry

    Steenhuis, H.J.; de Bruijn, E.J.; Heerkens, Johannes M.G.

    2007-01-01

    This paper analyses the technology development and technology transfer strategies in the aircraft manufacturing industry for four industrially developing countries. It is concluded from four case studies that technology catch-up is extremely difficult due to aircraft technology characteristics.

  4. Appropriate Technology as Indian Technology.

    Barry, Tom

    1979-01-01

    Describes the mounting enthusiasm of Indian communities for appropriate technology as an inexpensive means of providing much needed energy and job opportunities. Describes the development of several appropriate technology projects, and the goals and activities of groups involved in utilizing low scale solar technology for economic development on…

  5. Recent activity on the post-irradiation analyses of nuclear fuels and actinide samples at JAERI

    Shinohara, Nobuo; Nakahara, Yoshinori; Kohno, Nobuaki; Tsujimoto, Kazufumi

    2003-01-01

    Radiochemical analyses of spent fuels have been carried out at JAERI for contributing to the development of nuclear technologies, where several samples from research reactors and nuclear power plants were analyzed to obtain isotopic compositions and burnups. The history and procedures of the radiochemical analyses are depicted and some recent results are given in this paper. (author)

  6. Technology '90

    1991-01-01

    The US Department of Energy (DOE) laboratories have a long history of excellence in performing research and development in a number of areas, including the basic sciences, applied-energy technology, and weapons-related technology. Although technology transfer has always been an element of DOE and laboratory activities, it has received increasing emphasis in recent years as US industrial competitiveness has eroded and efforts have increased to better utilize the research and development resources the laboratories provide. This document, Technology '90, is the latest in a series that is intended to communicate some of the many opportunities available for US industry and universities to work with the DOE and its laboratories in the vital activity of improving technology transfer to meet national needs. Technology '90 is divided into three sections: Overview, Technologies, and Laboratories. The Overview section describes the activities and accomplishments of the DOE research and development program offices. The Technologies section provides descriptions of new technologies developed at the DOE laboratories. The Laboratories section presents information on the missions, programs, and facilities of each laboratory, along with a name and telephone number of a technology transfer contact for additional information. Separate papers were prepared for appropriate sections of this report

  7. 7 CFR 98.3 - Analyses performed and locations of laboratories.

    2010-01-01

    ... the special laboratory analyses rendered by the Science and Technology as a result of an agreement... Sausage Fat, salt 4 Pork Sausage Fat, moisture 4 Pork Sausage Fat 4 Mil-P-44131A (Pork Steaks, Flaked... performed at any one of the Science and Technology (S&T) field laboratories as follows: (1) USDA, AMS...

  8. Wireless technologies for the Construction Sector

    Heller, Alfred; Orthmann, Christian

    2014-01-01

    the building sector and is therefore used to analyse requirements for alternative technologies. The motivation of the current work is to find upcoming technologies that bring improvements into the sector, for example improved life cycle costs and energy efficiencies, increasing quality, construction...... and operation efficiency and reducing faults and losses. The paper also lays out requirements expected by the sector. It will be shown that the wireless sensor network technology is a strong competitor that may meet the requirements. By analysing the application of such technologies throughout the building...... that follow the wireless sensor network, the paper will line up the requirements that the new technology has to meet to be introduced successfully....

  9. Digital Technologies as Education Innovation at Universities

    Kryukov, Vladimir; Gorin, Alexey

    2017-01-01

    This paper analyses the use of digital technology-based education innovations in higher education. It demonstrated that extensive implementation of digital technologies in universities is the main factor conditioning the acceleration of innovative changes in educational processes, while digital technologies themselves become one of the key…

  10. Soulful Technologies

    Fausing, Bent

    2010-01-01

    Samsung introduced in 2008 a mobile phone called "Soul" made with a human touch and including itself a "magic touch". Through the analysis of a Nokia mobile phone TV-commercials I want to examine the function and form of digital technology in everyday images. The mobile phone and its digital camera...... and other devices are depicted by everyday aesthetics as capable of producing a unique human presence and interaction. The medium, the technology is a necessary helper of this very special and lost humanity. Without the technology, no special humanity, no soul - such is the prophecy. This personification...... or anthropomorphism is important for the branding of new technology. Technology is seen as creating a techno-transcendence towards a more qualified humanity which is in contact with fundamental human values like intuition, vision, and sensing; all the qualities that technology, industrialization, and rationalization...

  11. Fracture analyses of WWER reactor pressure vessels

    Sievers, J.; Liu, X.

    1997-01-01

    In the paper first the methodology of fracture assessment based on finite element (FE) calculations is described and compared with simplified methods. The FE based methodology was verified by analyses of large scale thermal shock experiments in the framework of the international comparative study FALSIRE (Fracture Analyses of Large Scale Experiments) organized by GRS and ORNL. Furthermore, selected results from fracture analyses of different WWER type RPVs with postulated cracks under different loading transients are presented. 11 refs, 13 figs, 1 tab

  12. Fracture analyses of WWER reactor pressure vessels

    Sievers, J; Liu, X [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Koeln (Germany)

    1997-09-01

    In the paper first the methodology of fracture assessment based on finite element (FE) calculations is described and compared with simplified methods. The FE based methodology was verified by analyses of large scale thermal shock experiments in the framework of the international comparative study FALSIRE (Fracture Analyses of Large Scale Experiments) organized by GRS and ORNL. Furthermore, selected results from fracture analyses of different WWER type RPVs with postulated cracks under different loading transients are presented. 11 refs, 13 figs, 1 tab.

  13. Graphic-based musculoskeletal model for biomechanical analyses and animation.

    Chao, Edmund Y S

    2003-04-01

    The ability to combine physiology and engineering analyses with computer sciences has opened the door to the possibility of creating the 'Virtual Human' reality. This paper presents a broad foundation for a full-featured biomechanical simulator for the human musculoskeletal system physiology. This simulation technology unites the expertise in biomechanical analysis and graphic modeling to investigate joint and connective tissue mechanics at the structural level and to visualize the results in both static and animated forms together with the model. Adaptable anatomical models including prosthetic implants and fracture fixation devices and a robust computational infrastructure for static, kinematic, kinetic, and stress analyses under varying boundary and loading conditions are incorporated on a common platform, the VIMS (Virtual Interactive Musculoskeletal System). Within this software system, a manageable database containing long bone dimensions, connective tissue material properties and a library of skeletal joint system functional activities and loading conditions are also available and they can easily be modified, updated and expanded. Application software is also available to allow end-users to perform biomechanical analyses interactively. This paper details the design, capabilities, and features of the VIMS development at Johns Hopkins University, an effort possible only through academic and commercial collaborations. Examples using these models and the computational algorithms in a virtual laboratory environment are used to demonstrate the utility of this unique database and simulation technology. This integrated system will impact on medical education, basic research, device development and application, and clinical patient care related to musculoskeletal diseases, trauma, and rehabilitation.

  14. Stress analyses of ITER toroidal field coils under fault conditions

    Jong, C.T.J.

    1990-02-01

    The International Thermonuclear Experimental Reactor (ITER) is intended as an experimental thermonuclear tokamak reactor for testing the basic physics, performance and technologies essential to future fusion reactors. The ITER design will be based on extensive new design work, supported by new physical and technological results, and on the great body of experience built up over several years from previous national and international reactor studies. Conversely, the ITER design process should provide the fusion community with valuable insights into what key areas need further development or clarification as we move forward towards practical fusion power. As part of the design process of the ITER toroidal field coils the mechanical behaviour of the magnetic system under fault conditions has to be analysed in more detail. This paper describes the work carried out to create a detailed finite element model of two toroidal field coils as well as some results of linear elastic analyses with fault conditions. The analyses have been performed with the finite element code ANSYS. (author). 5 refs.; 8 figs.; 2 tabs

  15. Globalization & technology

    Narula, Rajneesh

    Technology and globalization are interdependent processes. Globalization has a fundamental influence on the creation and diffusion of technology, which, in turn, affects the interdependence of firms and locations. This volume examines the international aspect of this interdependence at two levels...... of innovation" understanding of learning. Narula and Smith reconcile an important paradox. On the one hand, locations and firms are increasingly interdependent through supranational organisations, regional integration, strategic alliances, and the flow of investments, technologies, ideas and people...

  16. Army Technology

    2015-02-01

    that allows them to perform applied research under the Institute for Biotechnology research team 1 2 3 20 | ARMY TECHNOLOGY MAGAZINE ...DASA(R&T) Deputy Assistant Secretary of the Army for Research and Technology Download the magazine , view online or read each individual story with...Army photo by Conrad Johnson) Front and back cover designs by Joe Stephens EXECUTIVE DEPUTY TO THE COMMANDING GENERAL Army Technology Magazine is an

  17. Technology alliances

    Torgerson, D.F.; Boczar, P.G.; Kugler, G.

    1991-10-01

    In the field of nuclear technology, Canada and Korea developed a highly successful relationship that could serve as a model for other high-technology industries. This is particularly significant when one considers the complexity and technical depth required to design, build and operate a nuclear reactor. This paper will outline the overall framework for technology transfer and cooperation between Canada and Korea, and will focus on cooperation in nuclear R and D between the two countries

  18. Technological risks

    Klinke, A.; Renn, O.

    1998-01-01

    The empirical part about the technological risks deals with different technologies: nuclear energy, early warning systems of nuclear weapons and NBC-weapons, and electromagnetic fields. The potential of damage, the contemporary management strategies and the relevant characteristics will be described for each technology: risks of nuclear energy; risks of early warning systems of nuclear weapons and NBC-weapons; risks of electromagnetic fields. (authors)

  19. Technological risks

    Klinke, A.; Renn, O. [Center of Technology Assessment in Baden-Wuerttemberg, Stuttgart (Germany)

    1998-07-01

    The empirical part about the technological risks deals with different technologies: nuclear energy, early warning systems of nuclear weapons and NBC-weapons, and electromagnetic fields. The potential of damage, the contemporary management strategies and the relevant characteristics will be described for each technology: risks of nuclear energy; risks of early warning systems of nuclear weapons and NBC-weapons; risks of electromagnetic fields. (authors)

  20. [Anne Arold. Kontrastive Analyse...] / Paul Alvre

    Alvre, Paul, 1921-2008

    2001-01-01

    Arvustus: Arold, Anne. Kontrastive analyse der Wortbildungsmuster im Deutschen und im Estnischen (am Beispiel der Aussehensadjektive). Tartu, 2000. (Dissertationes philologiae germanicae Universitatis Tartuensis)

  1. Chemistry Technology

    Federal Laboratory Consortium — Chemistry technology experts at NCATS engage in a variety of innovative translational research activities, including:Design of bioactive small molecules.Development...

  2. Developing human technology curriculum

    Teija Vainio

    2012-10-01

    Full Text Available During the past ten years expertise in human-computer interaction has shifted from humans interacting with desktop computers to individual human beings or groups of human beings interacting with embedded or mobile technology. Thus, humans are not only interacting with computers but with technology. Obviously, this shift should be reflected in how we educate human-technology interaction (HTI experts today and in the future. We tackle this educational challenge first by analysing current Master’s-level education in collaboration with two universities and second, discussing postgraduate education in the international context. As a result, we identified core studies that should be included in the HTI curriculum. Furthermore, we discuss some practical challenges and new directions for international HTI education.

  3. Technology Catalogue

    1994-02-01

    The Department of Energy's Office of Environmental Restoration and Waste Management (EM) is responsible for remediating its contaminated sites and managing its waste inventory in a safe and efficient manner. EM's Office of Technology Development (OTD) supports applied research and demonstration efforts to develop and transfer innovative, cost-effective technologies to its site clean-up and waste management programs within EM's Office of Environmental Restoration and Office of Waste Management. The purpose of the Technology Catalogue is to provide performance data on OTD-developed technologies to scientists and engineers assessing and recommending technical solutions within the Department's clean-up and waste management programs, as well as to industry, other federal and state agencies, and the academic community. OTD's applied research and demonstration activities are conducted in programs referred to as Integrated Demonstrations (IDs) and Integrated Programs (IPs). The IDs test and evaluate.systems, consisting of coupled technologies, at specific sites to address generic problems, such as the sensing, treatment, and disposal of buried waste containers. The IPs support applied research activities in specific applications areas, such as in situ remediation, efficient separations processes, and site characterization. The Technology Catalogue is a means for communicating the status. of the development of these innovative technologies. The FY93 Technology Catalogue features technologies successfully demonstrated in the field through IDs and sufficiently mature to be used in the near-term. Technologies from the following IDs are featured in the FY93 Technology Catalogue: Buried Waste ID (Idaho National Engineering Laboratory, Idaho); Mixed Waste Landfill ID (Sandia National Laboratories, New Mexico); Underground Storage Tank ID (Hanford, Washington); Volatile organic compound (VOC) Arid ID (Richland, Washington); and VOC Non-Arid ID (Savannah River Site, South Carolina)

  4. An MDE Approach for Modular Program Analyses

    Yildiz, Bugra Mehmet; Bockisch, Christoph; Aksit, Mehmet; Rensink, Arend

    Program analyses are an important tool to check if a system fulfills its specification. A typical implementation strategy for program analyses is to use an imperative, general-purpose language like Java, and access the program to be analyzed through libraries that offer an API for reading, writing

  5. Random error in cardiovascular meta-analyses

    Albalawi, Zaina; McAlister, Finlay A; Thorlund, Kristian

    2013-01-01

    BACKGROUND: Cochrane reviews are viewed as the gold standard in meta-analyses given their efforts to identify and limit systematic error which could cause spurious conclusions. The potential for random error to cause spurious conclusions in meta-analyses is less well appreciated. METHODS: We exam...

  6. Diversity of primary care systems analysed.

    Kringos, D.; Boerma, W.; Bourgueil, Y.; Cartier, T.; Dedeu, T.; Hasvold, T.; Hutchinson, A.; Lember, M.; Oleszczyk, M.; Pavlick, D.R.

    2015-01-01

    This chapter analyses differences between countries and explains why countries differ regarding the structure and process of primary care. The components of primary care strength that are used in the analyses are health policy-making, workforce development and in the care process itself (see Fig.

  7. Approximate analyses of inelastic effects in pipework

    Jobson, D.A.

    1983-01-01

    This presentation shows figures concerned with analyses of inelastic effects in pipework as follows: comparison of experimental and calculated simplified analyses results for free end rotation and for circumferential strain; interrupted stress relaxation; regenerated relaxation caused by reversed yield; buckling of straight pipe under combined bending and torsion; results of fatigues test of pipe bend

  8. Thermally activated technologies: Technology Roadmap

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  9. Technology Exhibition

    Anon.

    1979-09-15

    Linked to the 25th Anniversary celebrations, an exhibition of some of CERN's technological achievements was opened on 22 June. Set up in a new 600 m{sup 2} Exhibition Hall on the CERN site, the exhibition is divided into eight technology areas — magnets, vacuum, computers and data handling, survey and alignment, radiation protection, beam monitoring and handling, detectors, and workshop techniques.

  10. Radiation Technology

    1990-01-01

    The conference was organized to evaluate the application directions of radiation technology in Vietnam and to utilize the Irradiation Centre in Hanoi with the Co-60 source of 110 kCi. The investigation and study of technico-economic feasibility for technology development to various items of food and non-food objects was reported. (N.H.A)

  11. Technology Transformation

    Scott, Heather; McGilll, Toria

    2011-01-01

    Social networking and other technologies, if used judiciously, present the means to integrate 21st century skills into the classroom curriculum. But they also introduce challenges that educators must overcome. Increased concerns about plagiarism and access to technology can test educators' creativity and school resources. Air Academy High School,…

  12. Maritime Technology

    Sørensen, Herman

    1997-01-01

    Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text.......Elementary introduction to the subject "Maritime Technology".The contents include drawings, sketches and references in English without any supplementary text....

  13. Energy and exergy analyses of electrolytic hydrogen production

    Rosen, M A [Ryerson Polytechnic Univ., Toronto, ON (Canada). Dept. of Mechanical Engineering

    1995-07-01

    The thermodynamic performance is investigated of a water-electrolysis process for producing hydrogen, based on current-technology equipment. Both energy and exergy analyses are used. Three cases are considered in which the principal driving energy inputs are (i) electricity, (ii) the high-temperature heat used to generate the electricity, and (iii) the heat source used to produce the high-temperature heat. The nature of the heat source (e.g.) fossil fuel, nuclear fuel, solar energy, (etc.) is left as general as possible. The analyses indicate that, when the main driving input is the hypothetical heat source, the principal thermodynamic losses are associated with water splitting, electricity generation and heat production; the losses are mainly due to the irreversibilities associated with converting a heat source to heat, and heat transfer across large temperature differences. The losses associated with the waste heat in used cooling water, because of its low quality, are not as significant as energy analysis indicates. (Author)

  14. Sensemaking technology

    Madsen, Charlotte Øland

    Research objective: The object of the LOK research project is to gain a better understanding of the technological strategic processes in organisations by using the concept/metaphor of sensemaking. The project will investigate the technological strategies in organisations in order to gain a deeper...... understanding of the cognitive competencies and barriers towards implementing new technology in organisations. The research will therefore concentrate on researching the development process in the organisation's perception of the external environmental elements of customers, suppliers, competitors, internal...... and external technology and legislation and the internal environmental elements of structure, power relations and political arenas. All of these variables have influence on which/how technologies are implemented thus creating different outcomes all depending on the social dynamics that are triggered by changes...

  15. A review of bioinformatic methods for forensic DNA analyses.

    Liu, Yao-Yuan; Harbison, SallyAnn

    2018-03-01

    Short tandem repeats, single nucleotide polymorphisms, and whole mitochondrial analyses are three classes of markers which will play an important role in the future of forensic DNA typing. The arrival of massively parallel sequencing platforms in forensic science reveals new information such as insights into the complexity and variability of the markers that were previously unseen, along with amounts of data too immense for analyses by manual means. Along with the sequencing chemistries employed, bioinformatic methods are required to process and interpret this new and extensive data. As more is learnt about the use of these new technologies for forensic applications, development and standardization of efficient, favourable tools for each stage of data processing is being carried out, and faster, more accurate methods that improve on the original approaches have been developed. As forensic laboratories search for the optimal pipeline of tools, sequencer manufacturers have incorporated pipelines into sequencer software to make analyses convenient. This review explores the current state of bioinformatic methods and tools used for the analyses of forensic markers sequenced on the massively parallel sequencing (MPS) platforms currently most widely used. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Medical Isotope Production Analyses In KIPT Neutron Source Facility

    Talamo, Alberto; Gohar, Yousry

    2016-01-01

    Medical isotope production analyses in Kharkov Institute of Physics and Technology (KIPT) neutron source facility were performed to include the details of the irradiation cassette and the self-shielding effect. An updated detailed model of the facility was used for the analyses. The facility consists of an accelerator-driven system (ADS), which has a subcritical assembly using low-enriched uranium fuel elements with a beryllium-graphite reflector. The beryllium assemblies of the reflector have the same outer geometry as the fuel elements, which permits loading the subcritical assembly with different number of fuel elements without impacting the reflector performance. The subcritical assembly is driven by an external neutron source generated from the interaction of 100-kW electron beam with a tungsten target. The facility construction was completed at the end of 2015, and it is planned to start the operation during the year of 2016. It is the first ADS in the world, which has a coolant system for removing the generated fission power. Argonne National Laboratory has developed the design concept and performed extensive design analyses for the facility including its utilization for the production of different radioactive medical isotopes. 99 Mo is the parent isotope of 99m Tc, which is the most commonly used medical radioactive isotope. Detailed analyses were performed to define the optimal sample irradiation location and the generated activity, for several radioactive medical isotopes, as a function of the irradiation time.

  17. Medical Isotope Production Analyses In KIPT Neutron Source Facility

    Talamo, Alberto [Argonne National Lab. (ANL), Argonne, IL (United States); Gohar, Yousry [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-01

    Medical isotope production analyses in Kharkov Institute of Physics and Technology (KIPT) neutron source facility were performed to include the details of the irradiation cassette and the self-shielding effect. An updated detailed model of the facility was used for the analyses. The facility consists of an accelerator-driven system (ADS), which has a subcritical assembly using low-enriched uranium fuel elements with a beryllium-graphite reflector. The beryllium assemblies of the reflector have the same outer geometry as the fuel elements, which permits loading the subcritical assembly with different number of fuel elements without impacting the reflector performance. The subcritical assembly is driven by an external neutron source generated from the interaction of 100-kW electron beam with a tungsten target. The facility construction was completed at the end of 2015, and it is planned to start the operation during the year of 2016. It is the first ADS in the world, which has a coolant system for removing the generated fission power. Argonne National Laboratory has developed the design concept and performed extensive design analyses for the facility including its utilization for the production of different radioactive medical isotopes. 99Mo is the parent isotope of 99mTc, which is the most commonly used medical radioactive isotope. Detailed analyses were performed to define the optimal sample irradiation location and the generated activity, for several radioactive medical isotopes, as a function of the irradiation time.

  18. Level II Ergonomic Analyses, Dover AFB, DE

    1999-02-01

    IERA-RS-BR-TR-1999-0002 UNITED STATES AIR FORCE IERA Level II Ergonomie Analyses, Dover AFB, DE Andrew Marcotte Marilyn Joyce The Joyce...Project (070401881, Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE 4. TITLE AND SUBTITLE Level II Ergonomie Analyses, Dover...1.0 INTRODUCTION 1-1 1.1 Purpose Of The Level II Ergonomie Analyses : 1-1 1.2 Approach 1-1 1.2.1 Initial Shop Selection and Administration of the

  19. Automatic incrementalization of Prolog based static analyses

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

  20. Cost-Benefit Analyses of Transportation Investments

    Næss, Petter

    2006-01-01

    This paper discusses the practice of cost-benefit analyses of transportation infrastructure investment projects from the meta-theoretical perspective of critical realism. Such analyses are based on a number of untenable ontological assumptions about social value, human nature and the natural......-to-pay investigations. Accepting the ontological and epistemological assumptions of cost-benefit analysis involves an implicit acceptance of the ethical and political values favoured by these assumptions. Cost-benefit analyses of transportation investment projects tend to neglect long-term environmental consequences...

  1. Energy consumption and technological developments

    Okorokov, V.R.

    1990-02-01

    The paper determines an outline of the world energy prospects based on principal trends of the development of energy consumption analysed over the long past period. According to the author's conclusion the development of energy systems will be determined in the nearest future (30 - 40 years) by contemporary energy technologies based on the exploitation of traditional energy resources but in the far future technologies based on the exploitation of thermonuclear and solar energy will play the decisive role. (author)

  2. Ergonomics technology

    Jones, W. L.

    1977-01-01

    Major areas of research and development in ergonomics technology for space environments are discussed. Attention is given to possible applications of the technology developed by NASA in industrial settings. A group of mass spectrometers for gas analysis capable of fully automatic operation has been developed for atmosphere control on spacecraft; a version for industrial use has been constructed. Advances have been made in personal cooling technology, remote monitoring of medical information, and aerosol particle control. Experience gained by NASA during the design and development of portable life support units has recently been applied to improve breathing equipment used by fire fighters.

  3. Comparison with Russian analyses of meteor impact

    Canavan, G.H.

    1997-06-01

    The inversion model for meteor impacts is used to discuss Russian analyses and compare principal results. For common input parameters, the models produce consistent estimates of impactor parameters. Directions for future research are discussed and prioritized.

  4. 7 CFR 94.102 - Analyses available.

    2010-01-01

    ... analyses for total ash, fat by acid hydrolysis, moisture, salt, protein, beta-carotene, catalase... glycol, SLS, and zeolex. There are also be tests for starch, total sugars, sugar profile, whey, standard...

  5. Anthocyanin analyses of Vaccinium fruit dietary supplements

    Vaccinium fruit ingredients within dietary supplements were identified by comparisons with anthocyanin analyses of known Vaccinium profiles (demonstration of anthocyanin fingerprinting). Available Vaccinium supplements were purchased and analyzed; their anthocyanin profiles (based on HPLC separation...

  6. Analyse of Maintenance Cost in ST

    Jenssen, B W

    2001-01-01

    An analyse has been carried out in ST concerning the total costs for the division. Even though the target was the maintenance costs in ST, the global budget over has been analysed. This has been done since there is close relation between investments & consolidation and the required level for maintenance. The purpose of the analyse was to focus on maintenance cost in ST as a ratio of total maintenance costs over the replacement value of the equipment, and to make some comparisons with other industries and laboratories. Families of equipment have been defined and their corresponding ratios calculated. This first approach gives us some "quantitative" measurements. This analyse should be combined with performance indicators (more "qualitative" measurements) that are telling us how well we are performing. This will help us in defending our budget, make better priorities, and we will satisfy the requirements from our external auditors.

  7. Technology Innovation

    EPA produces innovative technologies and facilitates their creation in line with the Agency mission to create products such as the stormwater calculator, remote sensing, innovation clusters, and low-cost air sensors.

  8. Technology | FNLCR

    The Frederick National Laboratory develops and applies advanced, next-generation technologies to solve basic and applied problems in the biomedical sciences, and serves as a national resource of shared high-tech facilities.

  9. Plasma technology

    Drouet, M.G.

    1984-03-01

    IREQ was contracted by the Canadian Electrical Association to review plasma technology and assess the potential for application of this technology in Canada. A team of experts in the various aspects of this technology was assembled and each team member was asked to contribute to this report on the applications of plasma pertinent to his or her particular field of expertise. The following areas were examined in detail: iron, steel and strategic-metals production; surface treatment by spraying; welding and cutting; chemical processing; drying; and low-temperature treatment. A large market for the penetration of electricity has been identified. To build up confidence in the technology, support should be provided for selected R and D projects, plasma torch demonstrations at full power, and large-scale plasma process testing

  10. Exploration technology

    Roennevik, H.C. [Saga Petroleum A/S, Forus (Norway)

    1996-12-31

    The paper evaluates exploration technology. Topics discussed are: Visions; the subsurface challenge; the creative tension; the exploration process; seismic; geology; organic geochemistry; seismic resolution; integration; drilling; value creation. 4 refs., 22 figs.

  11. Safety analyses for reprocessing and waste processing

    1983-03-01

    Presentation of an incident analysis of process steps of the RP, simplified considerations concerning safety, and safety analyses of the storage and solidification facilities of the RP. A release tree method is developed and tested. An incident analysis of process steps, the evaluation of the SRL-study and safety analyses of the storage and solidification facilities of the RP are performed in particular. (DG) [de

  12. Risk analyses of nuclear power plants

    Jehee, J.N.T.; Seebregts, A.J.

    1991-02-01

    Probabilistic risk analyses of nuclear power plants are carried out by systematically analyzing the possible consequences of a broad spectrum of causes of accidents. The risk can be expressed in the probabilities for melt down, radioactive releases, or harmful effects for the environment. Following risk policies for chemical installations as expressed in the mandatory nature of External Safety Reports (EVRs) or, e.g., the publication ''How to deal with risks'', probabilistic risk analyses are required for nuclear power plants

  13. Technological risk

    Dierkes, M; Coppock, R; Edwards, S

    1980-01-01

    The book begins with brief statements from representatives of political organizations. Part II presents an overview of the discussion about the control and management of technological progress. Parts III and IV discuss important elements in citizens' perception of technological risks and the development of consensus on how to deal with them. In Part V practical problems in the application of risk assessment and management, and in Part VI additional points are summarized.

  14. Lasers technology

    2014-01-01

    The Laser Technology Program of IPEN is developed by the Center for Lasers and Applications (CLA) and is committed to the development of new lasers based on the research of new optical materials and new resonator technologies. Laser applications and research occur within several areas such as Nuclear, Medicine, Dentistry, Industry, Environment and Advanced Research. Additional goals of the Program are human resource development and innovation, in association with Brazilian Universities and commercial partners

  15. Technological risk

    Dierkes, M.; Coppock, R.; Edwards, S.

    1980-01-01

    The book begins with brief statements from representatives of political organizations. Part II presents an overview of the discussion about the control and management of technological progress. Parts III and IV discuss important elements in citizens' perception of technological risks and the development of consensus on how to deal with them. In Part V practical problems in the application of risk assessment and management, and in Part VI additional points are summarized. (DG)

  16. Cognitive technologies

    Mello, Alan; Figueiredo, Fabrício; Figueiredo, Rafael

    2017-01-01

    This book focuses on the next generation optical networks as well as mobile communication technologies. The reader will find chapters on Cognitive Optical Network, 5G Cognitive Wireless, LTE, Data Analysis and Natural Language Processing. It also presents a comprehensive view of the enhancements and requirements foreseen for Machine Type Communication. Moreover, some data analysis techniques and Brazilian Portuguese natural language processing technologies are also described here. .

  17. The conceptual and practical challenges to technology categorisation in the preparation of technology needs assessments

    Nygaard, Ivan; Hansen, Ulrich Elmer

    2015-01-01

    the technology focus in the project, practice shows that the questions of what a technology is and how the key concepts of technology transfer and diffusion should be understood and operationalized remain diffuse. This paper explores the reasons for this by analysing the experience of the TNA project in using...... comprising varying degrees of software, orgware and hardware; ii) technologies appearing as whole systems of production; iii) technologies covering different application markets; and iv) technologies situated on a continuum between research, development and diffusion. These challenges are proxies...... be misleading. We therefore call for an increased focus on clarifying the technology concept in the training for the next generation of TNAs....

  18. Embodied energy and emergy analyses of a concentrating solar power (CSP) system

    Zhang Meimei; Wang Zhifeng; Xu Chao; Jiang Hui

    2012-01-01

    Although concentrating solar power (CSP) technology has been projected as one of the most promising candidates to replace conventional power plants burning fossil fuels, the potential advantages and disadvantages of the CSP technology have not been thoroughly evaluated. To better understand the performance of the CSP technology, this paper presents an ecological accounting framework based on embodied energy and emergy analyses methods. The analyses are performed for the 1.5 MW Dahan solar tower power plant in Beijing, China and different evaluation indices used in the embodied energy and emergy analyses are employed to evaluate the plant performance. Our analysis of the CSP plant are compared with six Italian power plants with different energy sources and an American PV plant, which demonstrates the CSP is the superior technology. - Highlights: ► Embodied energy and emergy analyses are employed to evaluate the first solar tower power plant in China. ► Different evaluation indices are quantitatively analyzed to show the advantages of CSP technology. ► This analysis provides insights for making energy policy and investment decisions about CSP technology.

  19. Technology cycles and technology revolutions

    Paganetto, Luigi; Scandizzo, Pasquale Lucio

    2010-09-15

    Technological cycles have been characterized as the basis of long and continuous periods economic growth through sustained changes in total factor productivity. While this hypothesis is in part consistent with several theories of growth, the sheer magnitude and length of the economic revolutions experienced by humankind seems to indicate surmise that more attention should be given to the origin of major technological and economic changes, with reference to one crucial question: role of production and use of energy in economic development.

  20. Technological change and social change

    Janshen, D.; Keck, O.; Webler, W.D.

    1981-01-01

    Political disputes about the risks and social consequences of modern technologies let many people ask whether society still has an independent capacity to act on the technological change or whether it is not rather the passive object of an obscure development. Modern technology is a challenge not only to the analytical capacity of social sciences. This volume describes the contributions of a conference which took place in April 1979. The first part deals with the social consequences of new technologies. Hereby new communication technologies are the main theme. The contributions of the second part deal with political, organizational, and methodical problems of the sociologic accessory research of technical and social innovations. The texts of the third part analyse experience so far made in the state support of research and technical development. (orig./HP) [de

  1. A Review of Some Superconducting Technologies for AtLAST: Parametric Amplifiers, Kinetic Inductance Detectors, and On-Chip Spectrometers

    Noroozian, Omid

    2018-01-01

    The current state of the art for some superconducting technologies will be reviewed in the context of a future single-dish submillimeter telescope called AtLAST. The technologies reviews include: 1) Kinetic Inductance Detectors (KIDs), which have now been demonstrated in large-format kilo-pixel arrays with photon background-limited sensitivity suitable for large field of view cameras for wide-field imaging. 2) Parametric amplifiers - specifically the Traveling-Wave Kinetic Inductance (TKIP) amplifier - which has enormous potential to increase sensitivity, bandwidth, and mapping speed of heterodyne receivers, and 3) On-chip spectrometers, which combined with sensitive direct detectors such as KIDs or TESs could be used as Multi-Object Spectrometers on the AtLAST focal plane, and could provide low-medium resolution spectroscopy of 100 objects at a time in each field of view.

  2. Climate and Electricity Annual 2011 - Data and Analyses

    NONE

    2011-05-27

    Electricity use is growing worldwide, providing a range of energy services: lighting, heating and cooling, specific industrial uses, entertainment, information technologies, and mobility. Because its generation remains largely based on fossil fuels, electricity is also the largest and the fastest-growing source of energy-related CO2 emissions, the primary cause of human-induced climate change. Forecasts from the IEA and others show that 'decarbonising' electricity and enhancing end-use efficiency can make major contributions to the fight against climate change. Global and regional trends on electricity supply and demand indicate the magnitude of the decarbonisation challenge ahead. As climate concerns become an essential component of energy policy-making, the generation and use of electricity will be subject to increasingly strong policy actions by governments to reduce their associated CO2 emissions. Despite these actions, and despite very rapid growth in renewable energy generation, significant technology and policy challenges remain if this unprecedented essential transition is to be achieved. This publication provides an authoritative resource on progress to date in this area, with statistics related to CO2 and the electricity sector across ten regions of the world. It also presents topical analyses on meeting the challenge of rapidly curbing CO2 emissions from electricity, from both a policy and technology perspective.

  3. Mass separated neutral particle energy analyser

    Takeuchi, Hiroshi; Matsuda, Toshiaki; Miura, Yukitoshi; Shiho, Makoto; Maeda, Hikosuke; Hashimoto, Kiyoshi; Hayashi, Kazuo.

    1983-09-01

    A mass separated neutral particle energy analyser which could simultaneously measure hydrogen and deuterium atoms emitted from tokamak plasma was constructed. The analyser was calibrated for the energy and mass separation in the energy range from 0.4 keV to 9 keV. In order to investigate the behavior of deuteron and proton in the JFT-2 tokamak plasma heated with ion cyclotron wave and neutral beam injection, this analyser was installed in JFT-2 tokamak. It was found that the energy spectrum could be determined with sufficient accuracy. The obtained ion temperature and ratio of deuteron and proton density from the energy spectrum were in good agreement with the value deduced from Doppler broadening of TiXIV line and the line intensities of H sub(α) and D sub(α) respectively. (author)

  4. Advanced toroidal facility vaccuum vessel stress analyses

    Hammonds, C.J.; Mayhall, J.A.

    1987-01-01

    The complex geometry of the Advance Toroidal Facility (ATF) vacuum vessel required special analysis techniques in investigating the structural behavior of the design. The response of a large-scale finite element model was found for transportation and operational loading. Several computer codes and systems, including the National Magnetic Fusion Energy Computer Center Cray machines, were implemented in accomplishing these analyses. The work combined complex methods that taxed the limits of both the codes and the computer systems involved. Using MSC/NASTRAN cyclic-symmetry solutions permitted using only 1/12 of the vessel geometry to mathematically analyze the entire vessel. This allowed the greater detail and accuracy demanded by the complex geometry of the vessel. Critical buckling-pressure analyses were performed with the same model. The development, results, and problems encountered in performing these analyses are described. 5 refs., 3 figs

  5. Thermal and stress analyses with ANSYS program

    Kanoo, Iwao; Kawaguchi, Osamu; Asakura, Junichi.

    1975-03-01

    Some analyses of the heat conduction and elastic/inelastic stresses, carried out in Power Reactor and Nuclear Fuel Development Corporation (PNC) in fiscal 1973 using ANSYS (Engineering Analysis System) program, are summarized. In chapter I, the present state of structural analysis programs available for a FBR (fast breeder reactor) in PNC is explained. Chapter II is a brief description of the ANSYS current status. In chapter III are presented 8 examples of the steady-state and transient thermal analyses for fast-reactor plant components, and in chapter IV 5 examples of the inelastic structural analysis. With the advance in the field of finite element method, its applications in design study should extend progressively in the future. The present report, it is hoped, will contribute as references in similar analyses and at the same time help to understand the deformation and strain behaviors of structures. (Mori, K.)

  6. Periodic safety analyses; Les essais periodiques

    Gouffon, A; Zermizoglou, R

    1990-12-01

    The IAEA Safety Guide 50-SG-S8 devoted to 'Safety Aspects of Foundations of Nuclear Power Plants' indicates that operator of a NPP should establish a program for inspection of safe operation during construction, start-up and service life of the plant for obtaining data needed for estimating the life time of structures and components. At the same time the program should ensure that the safety margins are appropriate. Periodic safety analysis are an important part of the safety inspection program. Periodic safety reports is a method for testing the whole system or a part of the safety system following the precise criteria. Periodic safety analyses are not meant for qualification of the plant components. Separate analyses are devoted to: start-up, qualification of components and materials, and aging. All these analyses are described in this presentation. The last chapter describes the experience obtained for PWR-900 and PWR-1300 units from 1986-1989.

  7. Smart technology

    Bruckner, D.G.

    1991-01-01

    The success of smart technology in the pursuit of the Gulf War has accentuated the awareness of how the Safeguards and Security disciplines are changing in response to new weaponry. Throughout the Department of Energy Integrated Complex (IC) Safeguards and Security efforts such as: Protection Programs Operations; Materials, Controls and Accountability; Information Security; Computer Security; Operational Security; Personnel Security, Safeguards and/or Security (S and S) surveys, and Inspections and Evaluations are undergoing a reassessment and refocusing. Some of this is in response to such things as the DOE initiated Freeze Report and the Drell Report. An important aspect is also technological, adjusting the way business is done in light of the weapons, tools and processes/procedures becoming available. This paper addresses the S and S issues with the promise of using smart technology to develop new approaches and equipment across the IC

  8. Seafood Technology

    Børresen, Torger

    This presentation will fill the total picture of this conference between fisheries and aquaculture, blue biotech and bioconservation, by considering the optimal processing technology of marine resources from the raw material until the seafood reaches the plate of the consumer. The situation today...... must be performed such that total traceability and authenticity of the final products can be presented on demand. The most important aspects to be considered within seafood technology today are safety, healthy products and high eating quality. Safety can be divided into microbiological safety...... and not presenting any safety risk per se. Seafood is healthy due to the omega-3 fatty acids and the nutritional value of vitamins, peptides and proteins. The processing technology must however be performed such that these valuable features are not lost during production. The same applies to the eating quality. Any...

  9. Persuasive Technology

    This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included in this vol......This book constitutes the proceedings of the 5th International Conference on Persuasive Technology, PERSUASIVE 2010, held in Copenhagen Denmark in June 2010. The 25 papers presented were carefully reviewed and selected from 80 submissions. In addition three keynote papers are included...... in this volume. The topics covered are emotions and user experience, ambient persuasive systems, persuasive design, persuasion profiles, designing for health, psychology of persuasion, embodied and conversational agents, economic incentives, and future directions for persuasive technology....

  10. Technology Management

    Pilkington, Alan

    2014-01-01

    This paper reports a bibliometric analysis (co-citation network analysis) of 10 journals in the management of technology (MOT) field. As well as introducing various bibliometric ideas, network analysis tools identify and explore the concepts covered by the field and their inter-relationships. Spe......This paper reports a bibliometric analysis (co-citation network analysis) of 10 journals in the management of technology (MOT) field. As well as introducing various bibliometric ideas, network analysis tools identify and explore the concepts covered by the field and their inter......-relationships. Specific results from different levels of analysis show the different dimensions of technology management: • Co-word terms identify themes • Journal co-citation network: linking to other disciplines • Co-citation network show concentrations of themes The analysis shows that MOT has a bridging role...

  11. Superconducting technology

    2010-01-01

    Superconductivity has a long history of about 100 years. Over the past 50 years, progress in superconducting materials has been mainly in metallic superconductors, such as Nb, Nb-Ti and Nb 3 Sn, resulting in the creation of various application fields based on the superconducting technologies. High-T c superconductors, the first of which was discovered in 1986, have been changing the future vision of superconducting technology through the development of new application fields such as power cables. On basis of these trends, future prospects of superconductor technology up to 2040 are discussed. In this article from the viewpoints of material development and the applications of superconducting wires and electronic devices. (author)

  12. Cogeneration technologies, optimisation and implementation

    Frangopoulos, Christos A

    2017-01-01

    Cogeneration refers to the use of a power station to deliver two or more useful forms of energy, for example, to generate electricity and heat at the same time. This book provides an integrated treatment of cogeneration, including a tour of the available technologies and their features, and how these systems can be analysed and optimised.

  13. Touch technologies in primary education

    Davidsen, Jacob

    This paper presents findings from a longitude project on children‘s use of interactive touchscreens in classroom-settings. By exploring and analysing interaction among pairs, children‘s collaborative activities are under study, and it is highlighted how touch technologies invites for a more...

  14. A Simple, Reliable Precision Time Analyser

    Joshi, B. V.; Nargundkar, V. R.; Subbarao, K.; Kamath, M. S.; Eligar, S. K. [Atomic Energy Establishment Trombay, Bombay (India)

    1966-06-15

    A 30-channel time analyser is described. The time analyser was designed and built for pulsed neutron research but can be applied to other uses. Most of the logic is performed by means of ferrite memory core and transistor switching circuits. This leads to great versatility, low power consumption, extreme reliability and low cost. The analyser described provides channel Widths from 10 {mu}s to 10 ms; arbitrarily wider channels are easily obtainable. It can handle counting rates up to 2000 counts/min in each channel with less than 1% dead time loss. There is a provision for an initial delay equal to 100 channel widths. An input pulse de-randomizer unit using tunnel diodes ensures exactly equal channel widths. A brief description of the principles involved in core switching circuitry is given. The core-transistor transfer loop is compared with the usual core-diode loops and is shown to be more versatile and better adapted to the making of a time analyser. The circuits derived from the basic loop are described. These include the scale of ten, the frequency dividers and the delay generator. The current drivers developed for driving the cores are described. The crystal-controlled clock which controls the width of the time channels and synchronizes the operation of the various circuits is described. The detector pulse derandomizer unit using tunnel diodes is described. The scheme of the time analyser is then described showing how the various circuits can be integrated together to form a versatile time analyser. (author)

  15. CIEMAT analyses of transition fuel cycle scenarios

    Alvarez-Velarde, F.; Gonzalez-Romero, E.M.

    2010-01-01

    The efficient design of strategies for the long-term sustainability of nuclear energy or the phase-out of this technology is possible after the study of transition scenarios from the current fuel cycle to a future one with advanced technologies and concepts. CIEMAT has participated in numerous fuel cycle scenarios studies for more than a decade and, from some years ago, special attention has been put in the study of transition scenarios. In this paper, the main characteristics of each studied transition scenario are described. The main results and partial conclusions of each scenario are also analyzed. As general conclusions of transition studies, we highlight that the advantages of advanced technologies in transition scenarios can be obtained by countries or regions with sufficiently large nuclear parks, with a long-term implementation of the strategy. For small countries, these advantages are also accessible with an affordable cost, by means of the regional collaboration during several decades. (authors)

  16. Technology Transfer

    Smith, Nanette R.

    1995-01-01

    The objective of this summer's work was to attempt to enhance Technology Application Group (TAG) ability to measure the outcomes of its efforts to transfer NASA technology. By reviewing existing literature, by explaining the economic principles involved in evaluating the economic impact of technology transfer, and by investigating the LaRC processes our William & Mary team has been able to lead this important discussion. In reviewing the existing literature, we identified many of the metrics that are currently being used in the area of technology transfer. Learning about the LaRC technology transfer processes and the metrics currently used to track the transfer process enabled us to compare other R&D facilities to LaRC. We discuss and diagram impacts of technology transfer in the short run and the long run. Significantly, it serves as the basis for analysis and provides guidance in thinking about what the measurement objectives ought to be. By focusing on the SBIR Program, valuable information regarding the strengths and weaknesses of this LaRC program are to be gained. A survey was developed to ask probing questions regarding SBIR contractors' experience with the program. Specifically we are interested in finding out whether the SBIR Program is accomplishing its mission, if the SBIR companies are providing the needed innovations specified by NASA and to what extent those innovations have led to commercial success. We also developed a survey to ask COTR's, who are NASA employees acting as technical advisors to the SBIR contractors, the same type of questions, evaluating the successes and problems with the SBIR Program as they see it. This survey was developed to be implemented interactively on computer. It is our hope that the statistical and econometric studies that can be done on the data collected from all of these sources will provide insight regarding the direction to take in developing systematic evaluations of programs like the SBIR Program so that they can

  17. Technological Innovations from NASA

    Pellis, Neal R.

    2006-01-01

    The challenge of human space exploration places demands on technology that push concepts and development to the leading edge. In biotechnology and biomedical equipment development, NASA science has been the seed for numerous innovations, many of which are in the commercial arena. The biotechnology effort has led to rational drug design, analytical equipment, and cell culture and tissue engineering strategies. Biomedical research and development has resulted in medical devices that enable diagnosis and treatment advances. NASA Biomedical developments are exemplified in the new laser light scattering analysis for cataracts, the axial flow left ventricular-assist device, non contact electrocardiography, and the guidance system for LASIK surgery. Many more developments are in progress. NASA will continue to advance technologies, incorporating new approaches from basic and applied research, nanotechnology, computational modeling, and database analyses.

  18. Fundamental data analyses for measurement control

    Campbell, K.; Barlich, G.L.; Fazal, B.; Strittmatter, R.B.

    1987-02-01

    A set of measurment control data analyses was selected for use by analysts responsible for maintaining measurement quality of nuclear materials accounting instrumentation. The analyses consist of control charts for bias and precision and statistical tests used as analytic supplements to the control charts. They provide the desired detection sensitivity and yet can be interpreted locally, quickly, and easily. The control charts provide for visual inspection of data and enable an alert reviewer to spot problems possibly before statistical tests detect them. The statistical tests are useful for automating the detection of departures from the controlled state or from the underlying assumptions (such as normality). 8 refs., 3 figs., 5 tabs

  19. A theoretical framework for analysing preschool teaching

    Chaiklin, Seth

    2014-01-01

    This article introduces a theoretical framework for analysing preschool teaching as a historically-grounded societal practice. The aim is to present a unified framework that can be used to analyse and compare both historical and contemporary examples of preschool teaching practice within and across...... national traditions. The framework has two main components, an analysis of preschool teaching as a practice, formed in relation to societal needs, and an analysis of the categorical relations which necessarily must be addressed in preschool teaching activity. The framework is introduced and illustrated...

  20. Power System Oscillatory Behaviors: Sources, Characteristics, & Analyses

    Follum, James D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tuffner, Francis K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dosiek, Luke A. [Union College, Schenectady, NY (United States); Pierre, John W. [Univ. of Wyoming, Laramie, WY (United States)

    2017-05-17

    This document is intended to provide a broad overview of the sources, characteristics, and analyses of natural and forced oscillatory behaviors in power systems. These aspects are necessarily linked. Oscillations appear in measurements with distinguishing characteristics derived from the oscillation’s source. These characteristics determine which analysis methods can be appropriately applied, and the results from these analyses can only be interpreted correctly with an understanding of the oscillation’s origin. To describe oscillations both at their source within a physical power system and within measurements, a perspective from the boundary between power system and signal processing theory has been adopted.