An Integrated Thermal Compensation System for MEMS Inertial Sensors

Directory of Open Access Journals (Sweden)

Sheng-Ren Chiu

2014-03-01

Full Text Available An active thermal compensation system for a low temperature-bias-drift (TBD MEMS-based gyroscope is proposed in this study. First, a micro-gyroscope is fabricated by a high-aspect-ratio silicon-on-glass (SOG process and vacuum packaged by glass frit bonding. Moreover, a drive/readout ASIC, implemented by the 0.25 µm 1P5M standard CMOS process, is designed and integrated with the gyroscope by directly wire bonding. Then, since the temperature effect is one of the critical issues in the high performance gyroscope applications, the temperature-dependent characteristics of the micro-gyroscope are discussed. Furthermore, to compensate the TBD of the micro-gyroscope, a thermal compensation system is proposed and integrated in the aforementioned ASIC to actively tune the parameters in the digital trimming mechanism, which is designed in the readout ASIC. Finally, some experimental results demonstrate that the TBD of the micro-gyroscope can be compensated effectively by the proposed compensation system.

The moderating effects of job control and selection, optimization, and compensation strategies on the age-work ability relationship

NARCIS (Netherlands)

Weigl, Matthias; Mueller, Andreas; Hornung, Severin; Zacher, Hannes; Angerer, Peter

Work ability describes employees' capability to carry out their work with respect to physical and psychological job demands. This study investigated direct and interactive effects of age, job control, and the use of successful aging strategies called selection, optimization, and compensation (SOC)

Rate dependent direct inverse hysteresis compensation of piezoelectric micro-actuator used in dual-stage hard disk drive head positioning system.

Science.gov (United States)

Rahman, Md Arifur; Al Mamun, Abdullah; Yao, Kui

2015-08-01

The head positioning servo system in hard disk drive is implemented nowadays using a dual-stage actuator—the primary stage consisting of a voice coil motor actuator providing long range motion and the secondary stage controlling the position of the read/write head with fine resolution. Piezoelectric micro-actuator made of lead zirconate titanate (PZT) has been a popular choice for the secondary stage. However, PZT micro-actuator exhibits hysteresis—an inherent nonlinear characteristic of piezoelectric material. The advantage expected from using the secondary micro-actuator is somewhat lost by the hysteresis of the micro-actuator that contributes to tracking error. Hysteresis nonlinearity adversely affects the performance and, if not compensated, may cause inaccuracy and oscillation in the response. Compensation of hysteresis is therefore an important aspect for designing head-positioning servo system. This paper presents a new rate dependent model of hysteresis along with rigorous analysis and identification of the model. Parameters of the model are found using particle swarm optimization. Direct inverse of the proposed rate-dependent generalized Prandtl-Ishlinskii model is used as the hysteresis compensator. Effectiveness of the overall solution is underscored through experimental results.

Non-budgetary expenditure under section 06 27, non-budget item 681 11 - expenditure for indemnification according to the Fair Compensation Directive of June 2, 1986

International Nuclear Information System (INIS)

1986-01-01

The German Federal Government announces non-budgetary funds made available up to a total of DM 90 millions, for compensation to be paid for reasons of equity, in compliance with the Fair Compensation Directive (vegetables) of June 2, 1986. The money will be used for the most part to pay compensation for losses incurred by vegetable gardeners, for a minor part to compensate for losses by vegetable dealers. (orig./HP) [de

Dispersion compensation of fiber optic communication system with direct detection using artificial neural networks (ANNs)

Science.gov (United States)

Maghrabi, Mahmoud M. T.; Kumar, Shiva; Bakr, Mohamed H.

2018-02-01

This work introduces a powerful digital nonlinear feed-forward equalizer (NFFE), exploiting multilayer artificial neural network (ANN). It mitigates impairments of optical communication systems arising due to the nonlinearity introduced by direct photo-detection. In a direct detection system, the detection process is nonlinear due to the fact that the photo-current is proportional to the absolute square of the electric field intensity. The proposed equalizer provides the most efficient computational cost with high equalization performance. Its performance is comparable to the benchmark compensation performance achieved by maximum-likelihood sequence estimator. The equalizer trains an ANN to act as a nonlinear filter whose impulse response removes the intersymbol interference (ISI) distortions of the optical channel. Owing to the proposed extensive training of the equalizer, it achieves the ultimate performance limit of any feed-forward equalizer (FFE). The performance and efficiency of the equalizer is investigated by applying it to various practical short-reach fiber optic communication system scenarios. These scenarios are extracted from practical metro/media access networks and data center applications. The obtained results show that the ANN-NFFE compensates for the received BER degradation and significantly increases the tolerance to the chromatic dispersion distortion.

To the issue of increasing efficiency of VAR compensation

Directory of Open Access Journals (Sweden)

Світлана Костянтинівна Поднебенна

2015-11-01

Full Text Available This article describes the features of VAR compensation of variable loads. One of the most common non-symmetric non-linear power consumers are welding power sources. Time and duration of the work of these sources vary randomly. To compensate the consumption of reactive power on the basis of consumption data from the three-phase electricity meters is inefficient. Compensation devices power should be calculated taking into account the asymmetrical consumption/generation of reactive power per phase and changing consumption patterns. Thyristor-controlled reactor, thyristor-switched capacitors, hybrid VAR compensators, active compensators (STATCOMs, «dynamic capacitors» can be used as the VAR compensation devices. Thyristor-controlled reactors can provide smooth regulation of reactive power, but they have high weight and size parameters and are additional sources of higher harmonics. Thyristor-switched capacitors provide stepwise adjustment of reactive power and are subject to the current higher harmonics. Hybrid VAR compensators make it possible to isolate capacitors from the higher harmonics and ensure smooth regulation, which is achieved by active filter introduction to the reactive power compensation devices based on thyristor-switched capacitors. However, this increases the cost of a compensator and complicates its control system. STATCOMs provide smooth regulation of reactive power, but they are too expensive.Perspective direction in the development of effective VAR compensation devices is «dynamic capacitor». As a result of a feasibility study the prospects for further research of electrical grids power efficiency through the development of effective devices for VAR compensation have been established

On the compensation effect in heterogeneous catalysis

DEFF Research Database (Denmark)

Pedersen, Thomas Bligaard; Honkala, Johanna Karoliina; Logadottir, Ashildur

2003-01-01

For a class of heterogeneously catalyzed reactions, we explain the compensation effect in terms of a switching of kinetic regimes leading to a concomitant change in the apparent activation energy and in the prefactor for the overall rate of the reaction. We first use the ammonia synthesis...

Aeromagnetic Compensation for UAVs

Science.gov (United States)

Naprstek, T.; Lee, M. D.

2017-12-01

Aeromagnetic data is one of the most widely collected types of data in exploration geophysics. With the continuing prevalence of unmanned air vehicles (UAVs) in everyday life there is a strong push for aeromagnetic data collection using UAVs. However, apart from the many political and legal barriers to overcome in the development of UAVs as aeromagnetic data collection platforms, there are also significant scientific hurdles, primary of which is magnetic compensation. This is a well-established process in manned aircraft achieved through a combination of platform magnetic de-noising and compensation routines. However, not all of this protocol can be directly applied to UAVs due to fundamental differences in the platforms, most notably the decrease in scale causing magnetometers to be significantly closer to the avionics. As such, the methodology must be suitably adjusted. The National Research Council of Canada has collaborated with Aeromagnetic Solutions Incorporated to develop a standardized approach to de-noising and compensating UAVs, which is accomplished through a series of static and dynamic experiments. On the ground, small static tests are conducted on individual components to determine their magnetization. If they are highly magnetic, they are removed, demagnetized, or characterized such that they can be accounted for in the compensation. Dynamic tests can include measuring specific components as they are powered on and off to assess their potential effect on airborne data. The UAV is then flown, and a modified compensation routine is applied. These modifications include utilizing onboard autopilot current sensors as additional terms in the compensation algorithm. This process has been applied with success to fixed-wing and rotary-wing platforms, with both a standard manned-aircraft magnetometer, as well as a new atomic magnetometer, much smaller in scale.

An efficient dose-compensation method for proximity effect correction

International Nuclear Information System (INIS)

Wang Ying; Han Weihua; Yang Xiang; Zhang Yang; Yang Fuhua; Zhang Renping

2010-01-01

A novel simple dose-compensation method is developed for proximity effect correction in electron-beam lithography. The sizes of exposed patterns depend on dose factors while other exposure parameters (including accelerate voltage, resist thickness, exposing step size, substrate material, and so on) remain constant. This method is based on two reasonable assumptions in the evaluation of the compensated dose factor: one is that the relation between dose factors and circle-diameters is linear in the range under consideration; the other is that the compensated dose factor is only affected by the nearest neighbors for simplicity. Four-layer-hexagon photonic crystal structures were fabricated as test patterns to demonstrate this method. Compared to the uncorrected structures, the homogeneity of the corrected hole-size in photonic crystal structures was clearly improved. (semiconductor technology)

Three-directional motion compensation-based novel-look-up-table for video hologram generation of three-dimensional objects freely maneuvering in space.

Science.gov (United States)

Dong, Xiao-Bin; Kim, Seung-Cheol; Kim, Eun-Soo

2014-07-14

A new three-directional motion compensation-based novel-look-up-table (3DMC-NLUT) based on its shift-invariance and thin-lens properties, is proposed for video hologram generation of three-dimensional (3-D) objects moving with large depth variations in space. The input 3-D video frames are grouped into a set of eight in sequence, where the first and remaining seven frames in each set become the reference frame (RF) and general frames (GFs), respectively. Hence, each 3-D video frame is segmented into a set of depth-sliced object images (DOIs). Then x, y, and z-directional motion vectors are estimated from blocks and DOIs between the RF and each of the GFs, respectively. With these motion vectors, object motions in space are compensated. Then, only the difference images between the 3-directionally motion-compensated RF and each of the GFs are applied to the NLUT for hologram calculation. Experimental results reveal that the average number of calculated object points and the average calculation time of the proposed method have been reduced compared to those of the conventional NLUT, TR-NLUT and MPEG-NLUT by 38.14%, 69.48%, and 67.41% and 35.30%, 66.39%, and 64.46%, respectively.

Automatic error compensation in dc amplifiers

International Nuclear Information System (INIS)

Longden, L.L.

1976-01-01

When operational amplifiers are exposed to high levels of neutron fluence or total ionizing dose, significant changes may be observed in input voltages and currents. These changes may produce large errors at the output of direct-coupled amplifier stages. Therefore, the need exists for automatic compensation techniques. However, previously introduced techniques compensate only for errors in the main amplifier and neglect the errors induced by the compensating circuitry. In this paper, the techniques introduced compensate not only for errors in the main operational amplifier, but also for errors induced by the compensation circuitry. Included in the paper is a theoretical analysis of each compensation technique, along with advantages and disadvantages of each. Important design criteria and information necessary for proper selection of semiconductor switches will also be included. Introduced in this paper will be compensation circuitry for both resistive and capacitive feedback networks

MTB-USDH Compensation Tracking System (MTB-CTS)

Data.gov (United States)

US Agency for International Development — MTB-USDH Compensation Tracking System: is the USDH Compensation Tracking System (MTB-CTS) to assist managers in monitoring their payroll costs for U.S. direct hires....

[Vestibular compensation studies]. [Vestibular Compensation and Morphological Studies

Science.gov (United States)

Perachio, Adrian A. (Principal Investigator)

1996-01-01

The following topics are reported: neurophysiological studies on MVN neurons during vestibular compensation; effects of spinal cord lesions on VNC neurons during compensation; a closed-loop vestibular compensation model for horizontally canal-related MVN neurons; spatiotemporal convergence in VNC neurons; contributions of irregularly firing vestibular afferents to linear and angular VOR's; application to flight studies; metabolic measures in vestibular neurons; immediate early gene expression following vestibular stimulation; morphological studies on primary afferents, central vestibular pathways, vestibular efferent projection to the vestibular end organs, and three-dimensional morphometry and imaging.

Reactive power compensator

Science.gov (United States)

El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Reactive power compensator

Energy Technology Data Exchange (ETDEWEB)

El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Compensation of non-ideal beam splitter polarization distortion effect in Michelson interferometer

Science.gov (United States)

Liu, Yeng-Cheng; Lo, Yu-Lung; Liao, Chia-Chi

2016-02-01

A composite optical structure consisting of two quarter-wave plates and a single half-wave plate is proposed for compensating for the polarization distortion induced by a non-ideal beam splitter in a Michelson interferometer. In the proposed approach, the optimal orientations of the optical components within the polarization compensator are determined using a genetic algorithm (GA) such that the beam splitter can be treated as a free-space medium and modeled using a unit Mueller matrix accordingly. Two implementations of the proposed polarization controller are presented. In the first case, the compensator is placed in the output arm of Michelson interferometer such that the state of polarization of the interfered output light is equal to that of the input light. However, in this configuration, the polarization effects induced by the beam splitter in the two arms of the interferometer structure cannot be separately addressed. Consequently, in the second case, compensator structures are placed in the Michelson interferometer for compensation on both the scanning and reference beams. The practical feasibility of the proposed approach is introduced by considering a Mueller polarization-sensitive (PS) optical coherence tomography (OCT) structure with three polarization controllers in the input, reference and sample arms, respectively. In general, the results presented in this study show that the proposed polarization controller provides an effective and experimentally-straightforward means of compensating for the polarization distortion effects induced by the non-ideal beam splitters in Michelson interferometers and Mueller PS-OCT structures.

Blind I/Q imbalance compensation technique for direct-conversion digital radio transceivers

CSIR Research Space (South Africa)

De Witt, JJ

2009-05-01

Full Text Available . Digital signal processing techniques have widely been proposed to compensate for these mixer imperfections. Of these techniques, the class of blind compensation techniques seems very attractive since no test signals are required. This paper presents a...

Comparative experiments regarding approaches to feedforward hysteresis compensation for piezoceramic actuators

International Nuclear Information System (INIS)

Gu, Guo-Ying; Zhu, Li-Min

2014-01-01

Piezoceramic actuators (PCAs) are desired devices in many micro/nano-positioning applications. The performance of PCA-based applications is severely limited by the presence of hysteresis nonlinearity. To remedy the hysteresis nonlinearity in such systems, feedforward hysteresis compensation is the most common technique. In the literature, many different feedforward hysteresis compensation approaches have been developed, but there are no comparative studies of these approaches. Focusing on the modified Prandtl-Ishlinskii model (MPIM) for asymmetric hysteresis description of piezoceramic actuators, three feedforward hysteresis compensation approaches—inverse hysteresis compensation (IHC), without inverse hysteresis compensation (WIHC), and direct inverse hysteresis compensation (DIHC)—are developed and compared in this paper. Extensive comparative experiments were conducted on a PCA-actuated stage to verify the effectiveness of the three different feedforward control approaches to hysteresis compensation. The experimental results show that the performances among the three approaches are rather similar, and the main differences among them are due to the specific implementation of each approach. (paper)

Prototype heel effect compensation filter for cone-beam CT

International Nuclear Information System (INIS)

Mori, Shinichiro; Endo, Masahiro; Nishizawa, Kanae; Ohno, Mari; Miyazaki, Hiroaki; Tsujita, Kazuhiko; Saito, Yasuo

2005-01-01

The prototype cone-beam CT (CBCT) has a larger beam width than the conventional multi-detector row CT (MDCT). This causes a non-uniform angular distribution of the x-ray beam intensity known as the heel effect. Scan conditions for CBCT tube current are adjusted on the anode side to obtain an acceptable clinical image quality. However, as the dose is greater on the cathode side than on the anode side, the signal-to-noise ratio on the cathode side is excessively high, resulting in an unnecessary dose amount. To compensate for the heel effect, we developed a heel effect compensation (HEC) filter. The HEC filter rendered the dose distribution uniform and reduced the dose by an average of 25% for free air and by 20% for CTDI phantoms compared to doses with the conventional filter. In addition, its effect in rendering the effective energy uniform resulted in an improvement in image quality. This new HEC filter may be useful in cone-beam CT studies. (note)

Attitudes toward the dubious compensation claim.

Science.gov (United States)

LEGGO, C

1951-07-01

Laws providing for compensation of workmen for occupational injury are a powerful socio-economic force. In settlement of compensation claims the goal, difficult to achieve, is fairness to employee, employer and insurance carrier. Often, medical, legal, economic and social considerations conflict with one another. A "fact" in one field may not be considered so in another. Since medical data and testimony often guide the ultimate decision of a compensation claim, the physician's attitude is a large factor not only immediately and directly in determination of the case at hand but, perhaps more important, in the ultimate direction of the socio-economic forces which spring from the sum of all such determinations. To perpetuate the good in workmen's compensation laws, the next generation of physicians-and of lawyers and business administrators as well, for they, too, are involved-ought to have basic training in the social sciences in order that they may have a broad rather than a segmental view of the problems with which they deal.

Compensation effects in molecular interactions and the quantum chemical le Chatelier principle.

Science.gov (United States)

Mezey, Paul G

2015-05-28

Components of molecular interactions and various changes in the components of total energy changes during molecular processes typically exhibit some degrees of compensation. This may be as prominent as the over 90% compensation of the electronic energy and nuclear repulsion energy components of the total energy in some conformational changes. Some of these compensations are enhanced by solvent effects. For various arrangements of ions in a solvent, however, not only compensation but also a formal, mutual enhancement between the electronic energy and nuclear repulsion energy components of the total energy may also occur, when the tools of nuclear charge variation are applied to establish quantum chemically rigorous energy inequalities.

Digital nonlinearity compensation in high-capacity optical communication systems considering signal spectral broadening effect.

Science.gov (United States)

Xu, Tianhua; Karanov, Boris; Shevchenko, Nikita A; Lavery, Domaniç; Liga, Gabriele; Killey, Robert I; Bayvel, Polina

2017-10-11

Nyquist-spaced transmission and digital signal processing have proved effective in maximising the spectral efficiency and reach of optical communication systems. In these systems, Kerr nonlinearity determines the performance limits, and leads to spectral broadening of the signals propagating in the fibre. Although digital nonlinearity compensation was validated to be promising for mitigating Kerr nonlinearities, the impact of spectral broadening on nonlinearity compensation has never been quantified. In this paper, the performance of multi-channel digital back-propagation (MC-DBP) for compensating fibre nonlinearities in Nyquist-spaced optical communication systems is investigated, when the effect of signal spectral broadening is considered. It is found that accounting for the spectral broadening effect is crucial for achieving the best performance of DBP in both single-channel and multi-channel communication systems, independent of modulation formats used. For multi-channel systems, the degradation of DBP performance due to neglecting the spectral broadening effect in the compensation is more significant for outer channels. Our work also quantified the minimum bandwidths of optical receivers and signal processing devices to ensure the optimal compensation of deterministic nonlinear distortions.

Workers' compensation in Pennsylvania: the effects of delayed contested cases.

Science.gov (United States)

Dawson, S E

1994-01-01

This study examines the effects of delayed workers' compensation cases in the Pennsylvania system. Forty-five claimants of a workers' compensation support group responded to interviews. Delay periods averaged two years with a 68.4% drop in income. Results indicate that claimants endured financial and emotional stress, exhausted personal assets, relied on assistance from relatives, and received public assistance. Implications for social work practice include educating workers about benefits, counseling claimants with delayed claims, and advocating for administrative reforms.

FY 2011 4th Quarter Metric: Estimate of Future Aerosol Direct and Indirect Effects

Energy Technology Data Exchange (ETDEWEB)

Koch, D

2011-09-21

The global and annual mean aerosol direct and indirect effects, relative to 1850 conditions, estimated from CESM simulations are 0.02 W m-2 and -0.39 W m-2, respectively, for emissions in year 2100 under the IPCC RCP8.5 scenario. The indirect effect is much smaller than that for 2000 emissions because of much smaller SO2 emissions in 2100; the direct effects are small due to compensation between warming by black carbon and cooling by sulfate.

Enthalpy - entropy compensation effect in grain boundary phenomena

Czech Academy of Sciences Publication Activity Database

Lejček, Pavel

2005-01-01

Roč. 96, č. 10 (2005), s. 1129-1133 ISSN 0044-3093 R&D Projects: GA MPO(CZ) FF-P2/053 Institutional research plan: CEZ:AV0Z10100520 Keywords : compensation effect * enthalpy * entropy * thermodynamics * grain boundary Subject RIV: BJ - Thermodynamics Impact factor: 0.842, year: 2005

Compensator design using the par scientific miller and ADAC Pinnacle tps

International Nuclear Information System (INIS)

Arthur, G.; White, S.

2001-01-01

Full text: Ideal compensators are designed so that a uniform dose is given to a specific plane within the treatment volume despite variation in surface contour and non-homogeneity within the volume. Traditionally our department has designed compensators based on missing tissue alone and using lead sheet. We have now acquired a Par Scientific compensator miller and ADAC Pinnacle compensator design software. This poster sets out the investigations carried out to design compensators using this equipment. The investigation consisted of four parts. Part one was an evaluation of the Par Scientific miller's ability to accurately and to reproducibly mill various shapes from foam and cerrobend. It also included an examination of the effects due to varying the parameter options available in the software and the use of substitute milling bits. The second part was the choice of material to be used for the compensator. The following were investigated for moulds: steel grit; steel shot and cerrobend and for direct milling: cerrobend. Part three consisted of an investigation into the effects on compensator design with changes in the many parameter options available in ADAC software. For the final part compensators were designed using the ADAC software for both a Head and Neck, and a Mantle case. The compensators were made using the Par Scientific miller. This consisted of milling the required shape in foam and then filling it with cerrobend. TLDs were used to evaluate the compensators. Evaluation consisted of examining the uniformity of dose in the selected plane. The compensators were also compared to the traditional method for the same cases. Finally a comparison was made of the measured dose with that calculated by the ADAC Pinnacle planning system. The Par Scientific was found to be accurate and consistent, however not suitable for milling solid cerrobend directly. Investigations so far have shown that the use of molten cerrobend poured into milled foam moulds is the most

Accurate torque control of a bi-directional magneto-rheological actuator considering hysteresis and friction effects

International Nuclear Information System (INIS)

Nguyen, Phuong-Bac; Choi, Seung-Bok

2013-01-01

This paper presents a novel type of magneto-rheological (MR) actuator called a bi-directional magneto-rheological (BMR) actuator and accurate torque control results considering both hysteresis and friction compensation. The induced torque of this actuator varies from negative to positive values. As a result, it can work as either a brake or a clutch depending on the scheme of current input. In our work, the configuration of the actuator as well as its driving system is presented first. Subsequently, a congruency hysteresis based (CBH) model to take account of the effect of the hysteresis is proposed. After that, a compensator based on this model is developed. In addition, the effect of dry friction, which exists inherently with MR actuators in general, is also considered. In order to assess the effectiveness of the hysteresis compensator, several experiments on modeling and control of the actuator with different waveforms are carried out. (paper)

Accurate torque control of a bi-directional magneto-rheological actuator considering hysteresis and friction effects

Science.gov (United States)

Nguyen, Phuong-Bac; Choi, Seung-Bok

2013-05-01

This paper presents a novel type of magneto-rheological (MR) actuator called a bi-directional magneto-rheological (BMR) actuator and accurate torque control results considering both hysteresis and friction compensation. The induced torque of this actuator varies from negative to positive values. As a result, it can work as either a brake or a clutch depending on the scheme of current input. In our work, the configuration of the actuator as well as its driving system is presented first. Subsequently, a congruency hysteresis based (CBH) model to take account of the effect of the hysteresis is proposed. After that, a compensator based on this model is developed. In addition, the effect of dry friction, which exists inherently with MR actuators in general, is also considered. In order to assess the effectiveness of the hysteresis compensator, several experiments on modeling and control of the actuator with different waveforms are carried out.

Kinetic compensation effect in the thermal desorption of a binary gas mixture

Science.gov (United States)

Zuniga-Hansen, Nayeli; Silbert, Leonardo E.; Calbi, M. Mercedes

The kinetic compensation effect, observed in many different areas of science, is the systematic change in the magnitudes of the Arrhenius parameters Ea, the energy of activation and ν, the preexponential factor, as a response to external perturbing parameters. Its existence continues to be debated as it has not been explicitly demonstrated and its physical origins remain poorly understood. As part of a systematic study of different factors that alter the energy of activation during thermal desorption, we have performed numerical studies of the effects of adsorbate-adsorbate interactions on the Arrhenius parameters, as well as the effects of changes in surface morphology. Our results have consistently shown that there is a partial compensation effect between Ea and lnν and a tendency towards isokinetic equilibrium when the system transitions from an interacting to a non-interacting regime. In the present work we study the effects of the presence of two different chemical species. With our systematic study we expect to provide a deeper insight into the microscopic events that originate compensation effects, not only in our system, but also in other fields where these effects have been reported.

The Motivate Effect of Higher Education Institutions' Compensation System on Faculties

Institute of Scientific and Technical Information of China (English)

GU Qing-liang; SU Jun

2007-01-01

Based on the questionnaire survey, this article reveals the effects of the current university compensation system on faculties in three psychological aspects, namely performance exam effect, work pressure and endurance capability. The results indicate that university faculties have a strong pursuit for self-fulfillment and successful career. Most of them love their teaching career and wish to further improve the fairness and efficiency of university management system by deepening the management systemic reform. Multi-leveled, multi-purposed and multi-modeled managing strategy of university compensation system is proved to be the main methods of improving fairness and efficiency.

Developing fair compensation structures

International Nuclear Information System (INIS)

Trousdale, W.J.

1998-01-01

The issue of finding an effective way to incorporate Aboriginal values into the process of developing fair compensation structures was discussed. This paper discusses pricing intangible values using dollars, but it was emphasized that 'values' are whatever are important to us. Therefore, in order to achieve fair compensation, creative alternatives that are value-focused should be pursued. In addition to the more straight-forward monetary compensation, compensation could also be about avoiding losses, mitigating adverse impacts, achieving better communication, and promoting cultural understanding. 25 refs., 2 tabs

Improvement of vector compensation method for vehicle magnetic distortion field

Energy Technology Data Exchange (ETDEWEB)

Pang, Hongfeng, E-mail: panghongfeng@126.com; Zhang, Qi; Li, Ji; Luo, Shitu; Chen, Dixiang; Pan, Mengchun; Luo, Feilu

2014-03-15

Magnetic distortions such as eddy-current field and low frequency magnetic field have not been considered in vector compensation methods. A new compensation method is proposed to suppress these magnetic distortions and improve compensation performance, in which the magnetic distortions related to measurement vectors and time are considered. The experimental system mainly consists of a three-axis fluxgate magnetometer (DM-050), an underwater vehicle and a proton magnetometer, in which the scalar value of magnetic field is obtained with the proton magnetometer and considered to be the true value. Comparing with traditional compensation methods, experimental results show that the magnetic distortions can be further reduced by two times. After compensation, error intensity and RMS error are reduced from 11684.013 nT and 7794.604 nT to 16.219 nT and 5.907 nT respectively. It suggests an effective way to improve the compensation performance of magnetic distortions. - Highlights: • A new vector compensation method is proposed for vehicle magnetic distortion. • The proposed model not only includes magnetometer error but also considers magnetic distortion. • Compensation parameters are computed directly by solving nonlinear equations. • Compared with traditional methods, the proposed method is not related with rotation angle rate. • Error intensity and RMS error can be reduced to 1/2 of the error with traditional methods.

Improvement of vector compensation method for vehicle magnetic distortion field

International Nuclear Information System (INIS)

Pang, Hongfeng; Zhang, Qi; Li, Ji; Luo, Shitu; Chen, Dixiang; Pan, Mengchun; Luo, Feilu

2014-01-01

Magnetic distortions such as eddy-current field and low frequency magnetic field have not been considered in vector compensation methods. A new compensation method is proposed to suppress these magnetic distortions and improve compensation performance, in which the magnetic distortions related to measurement vectors and time are considered. The experimental system mainly consists of a three-axis fluxgate magnetometer (DM-050), an underwater vehicle and a proton magnetometer, in which the scalar value of magnetic field is obtained with the proton magnetometer and considered to be the true value. Comparing with traditional compensation methods, experimental results show that the magnetic distortions can be further reduced by two times. After compensation, error intensity and RMS error are reduced from 11684.013 nT and 7794.604 nT to 16.219 nT and 5.907 nT respectively. It suggests an effective way to improve the compensation performance of magnetic distortions. - Highlights: • A new vector compensation method is proposed for vehicle magnetic distortion. • The proposed model not only includes magnetometer error but also considers magnetic distortion. • Compensation parameters are computed directly by solving nonlinear equations. • Compared with traditional methods, the proposed method is not related with rotation angle rate. • Error intensity and RMS error can be reduced to 1/2 of the error with traditional methods

Is Trust for Sale? The Effectiveness of Financial Compensation for Repairing Competence- versus Integrity-Based Trust Violations

Science.gov (United States)

Haesevoets, Tessa; Reinders Folmer, Chris; Van Hiel, Alain

2015-01-01

Despite the popularity of financial compensation as a means for addressing trust violations, the question whether (more) money can indeed buy trust back remains largely unexplored. In the present research, we focus on the role of violation type and compensation size. The results of a scenario study and a laboratory experiment show that financial compensation can effectively promote the restoration of trust for transgressions that indicate a lack of competence. Conversely, for transgressions which signal a lack of integrity, financial compensation is not an effective tool to repair trust. Moreover, our findings indicate that for both violation types, overcompensation has no positive effects on top of the impact of equal compensation. These findings therefore show that when it comes to trust, money cannot buy everything. PMID:26714025

Incorporating the effects of lateral spread of the primary fluence, into compensator design

International Nuclear Information System (INIS)

Reece, P.J.; Hoban, P.

2000-01-01

Full text: In this study we extended ideas developed by Faddegon and Pfalzner on the construction of patient specific compensating filters. Their research was essentially focused on formulating a general method for creating compensators using a 3D planning system. In their work Faddegon and Pfalzner utilized a simple attenuation model to convert transmission arrays into filter thickness arrays. The compensators constructed from these arrays produce the primary fluence required to give a uniform dose distribution at a specified depth. This technique does not account for local geometric variations hi compensator scattering conditions. Therefore we have devised a method to incorporate the effects of lateral spread of the primary fluence passing through the compensating filter. A 2D Gaussian kernel, generated from Monte Carlo measurements, was used to model the spread of the primary fluence in the compensating filter. A 'maximum likelihood' optimisation algorithm was employed to deconvolve the kernel from the desired primary fluence to produce a more realistic incident fluence and compensator thickness array. The CMS FOCUS planning system was used to generate transmission maps corresponding to the desired influence of the compensating filter. Two compensating filters were constructed for each map, one using the standard attenuation method and the other with our method. For each method, an assessment was made using film dosimetry, on the degree of correlation between the desired primary fluence and the primary fluence produced by the compensating filter. Our results indicate that for compensating filters which are relatively uniform in thickness, there is good agreement between desired and delivered fluence maps for both methods. For non-uniform compensating filters the attenuation method deviates more notably from the desired fluence map. As expected, both methods also show significant deviations around the edges of the filter. It is anticipated that the work done here

Nonlinear bias compensation of ZiYuan-3 satellite imagery with cubic splines

Science.gov (United States)

Cao, Jinshan; Fu, Jianhong; Yuan, Xiuxiao; Gong, Jianya

2017-11-01

Like many high-resolution satellites such as the ALOS, MOMS-2P, QuickBird, and ZiYuan1-02C satellites, the ZiYuan-3 satellite suffers from different levels of attitude oscillations. As a result of such oscillations, the rational polynomial coefficients (RPCs) obtained using a terrain-independent scenario often have nonlinear biases. In the sensor orientation of ZiYuan-3 imagery based on a rational function model (RFM), these nonlinear biases cannot be effectively compensated by an affine transformation. The sensor orientation accuracy is thereby worse than expected. In order to eliminate the influence of attitude oscillations on the RFM-based sensor orientation, a feasible nonlinear bias compensation approach for ZiYuan-3 imagery with cubic splines is proposed. In this approach, no actual ground control points (GCPs) are required to determine the cubic splines. First, the RPCs are calculated using a three-dimensional virtual control grid generated based on a physical sensor model. Second, one cubic spline is used to model the residual errors of the virtual control points in the row direction and another cubic spline is used to model the residual errors in the column direction. Then, the estimated cubic splines are used to compensate the nonlinear biases in the RPCs. Finally, the affine transformation parameters are used to compensate the residual biases in the RPCs. Three ZiYuan-3 images were tested. The experimental results showed that before the nonlinear bias compensation, the residual errors of the independent check points were nonlinearly biased. Even if the number of GCPs used to determine the affine transformation parameters was increased from 4 to 16, these nonlinear biases could not be effectively compensated. After the nonlinear bias compensation with the estimated cubic splines, the influence of the attitude oscillations could be eliminated. The RFM-based sensor orientation accuracies of the three ZiYuan-3 images reached 0.981 pixels, 0.890 pixels, and 1

Direct comparison of in vivo versus postmortem second-order motion-compensated cardiac diffusion tensor imaging.

Science.gov (United States)

Stoeck, Christian T; von Deuster, Constantin; Fleischmann, Thea; Lipiski, Miriam; Cesarovic, Nikola; Kozerke, Sebastian

2018-04-01

To directly compare in vivo versus postmortem second-order motion-compensated spin-echo diffusion tensor imaging of the porcine heart. Second-order motion-compensated spin-echo cardiac diffusion tensor imaging was performed during systolic contraction in vivo and repeated upon cardiac arrest by bariumchloride without repositioning of the study animal or replaning of imaging slices. In vivo and postmortem reproducibility was assessed by repeat measurements. Comparison of helix, transverse, and sheet (E2A) angulation as well as mean diffusivity and fractional anisotropy was performed. Intraclass correlation coefficients for repeated measurements (postmortem/in vivo) were 0.95/0.96 for helix, 0.70/0.66 for transverse, and 0.79/0.72 for E2A angulation; 0.83/0.72 for mean diffusivity; and 0.78/0.76 for fractional anisotropy. The corresponding 95% levels of agreement across the left ventricle were: helix 14 to 18°/12 to 15°, transverse 9 to 10°/10 to 11°, E2A 15 to 20°/16 to 18°. The 95% levels of agreement across the left ventricle for the comparison of postmortem versus in vivo were 20 to 22° for helix, 13 to 19° for transverse, and 24 to 31° for E2A angulation. Parameters derived from in vivo second-order motion-compensated spin-echo diffusion tensor imaging agreed well with postmortem imaging, indicating sufficient suppression of motion-induced signal distortions of in vivo cardiac diffusion tensor imaging. Magn Reson Med 79:2265-2276, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Apparent Power, Expanded Definitions, Transient Operating Conditions, Network Reactions, Compensation, Papers Presented at ETG Conference (Energy Technology Society), 1979

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

The Proceedings of the Conference comprises 12 papers dealing with the following themes: the history of apparent power; active and apparent power of periodical currents in single-phase and multiphase systems with periodical voltages of any shape of curve; power values in unsteady state processes; power and harmonic relations in mains-controlled direct frequency converters; power electronic devices for apparent power compensation; electric arc effects on power system: characteristics, measurement methods, compensation; harmonic compensation by means of impedance wave trap filters in rectifiers; compensation of apparent power by filter circuits; apparent power effects on ac railroad power systems; effects of apparent power in low-voltage networks of public power supply.

Radiation damage effects on calorimeter compensation

International Nuclear Information System (INIS)

Gabriel, T.A.; Handler, T.

1990-01-01

An important consideration in the design of a detector that is to be used at the Superconducting Super Collider (SSC) is the response of the calorimeter to electromagnetic and hadronic particles and the equality of those responses for different types of particles at equal incident energies, i.e. compensation. However, as the simulations that are reported show, the compensation characteristics of a calorimeter can be seriously compromised over a relatively short period of time due to the large radiation levels that are expected in the SSC environment. 6 refs., 3 figs

Effect of physical exercise prelabyrinthectomy on locomotor balance compensation in the squirrel monkey

Science.gov (United States)

Igarashi, M.; Ohashi, K.; Yoshihara, T.; MacDonald, S.

1989-01-01

This study examines the effectiveness of physical exercise, during a prepathology state, on locomotor balance compensation after subsequent unilateral labyrinthectomy in squirrel monkeys. An experimental group underwent 3 hr. of daily running exercise on a treadmill for 3 mo. prior to the surgery, whereas a control group was not exercised. Postoperatively, the locomotor balance function of both groups was tested for 3 mo. There was no significant difference in gait deviation counts in the acute phase of compensation. However, in the chronic compensation maintenance phase, the number of gait deviation counts was fewer in the exercise group, which showed significantly better performance stability.

The effect of practitioner compensation on HMO consumer satisfaction.

Science.gov (United States)

Scoggins, John F

2002-04-01

To test the hypothesis that a health maintenance organization (HMO) consumer's satisfaction depends on the way his or her health plan compensates practitioners. Consumer Assessment of Health Plans (CAHPS) survey data from 1999 and 2000 were provided by the Office of Public Insurance Counsel for the state of Texas. These data were combined with the Health Plan Employer Data and Information Set (HEDIS) quality measures of managed care health plans in Texas published by the Texas Health Care Information Council. The study fitted the CAHPS survey data to an ordered-probit model. The dependent variable was customer satisfaction with the health plan, using a rating scale from 0-10. The independent variables included the percentage of health plan practitioners compensated with capitated fees, the percentage compensated with a bonus or withholding incentive, and other health plan and consumer characteristics. Consumer satisfaction with HMOs is negatively correlated with the percentage of practitioners who are compensated on a capitated-fee basis and positively correlated with the percentage of practitioners compensated with a fee-withholding incentive (e.g., a fraction of fees that are withheld until specific quality and cost-control goals are reached). Neither the percentage compensated under a bonus incentive system nor the percentage of general practitioners with board certification correlated with HMO consumer satisfaction. A managed health plan's method of practitioner compensation can affect participant satisfaction in a predictable manner.

The Effects of Performance Measurement and Compensation on Motivation

OpenAIRE

Marco van Herpen; C. Mirjam van Praag; Kees Cools

2003-01-01

This paper analyzes empirically the relationship between pay and performance. Economic and psychological theories predict that the design and implementation of a performance measurement and compensation system affect the motivation of employees. Our survey results demonstrate a positive relationship between the perceived characteristics of the complete compensation system and extrinsic motivation. Intrinsic motivation is not affected by the design of monetary compensation, but by promotion op...

Quantum optical effective-medium theory for loss-compensated metamaterials

DEFF Research Database (Denmark)

Amooghorban, Ehsan; Mortensen, N. Asger; Wubs, Martijn

2013-01-01

A central aim in metamaterial research is to engineer subwavelength unit cells that give rise to desired effective-medium properties and parameters, such as a negative refractive index. Ideally one can disregard the details of the unit cell and employ the effective description instead. A popular...... effective parameters are insufficient to describe the propagation of quantum states of light. Furthermore, we propose a quantum optical effective-medium theory instead and show that it correctly predicts the properties of the light emerging from loss-compensated metamaterials. © 2013 American Physical...

Effect of ion compensation of the beam space charge on gyrotron operation

Energy Technology Data Exchange (ETDEWEB)

Fokin, A. P.; Glyavin, M. Yu. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Nusinovich, G. S. [Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20742-3511 (United States)

2015-04-15

In gyrotrons, the coherent radiation of electromagnetic waves takes place when the cyclotron resonance condition between the wave frequency and the electron cyclotron frequency or its harmonic holds. The voltage depression caused by the beam space charge field changes the relativistic cyclotron frequency and, hence, can play an important role in the beam-wave interaction process. In long pulse and continuous-wave regimes, the beam space charge field can be partially compensated by the ions, which appear due to the beam impact ionization of neutral molecules of residual gases in the interaction space. In the present paper, the role of this ion compensation of the beam space charge on the interaction efficiency is analyzed. We also analyze the effect of the electron velocity spread on the limiting currents and discuss some effects restricting the ion-to-beam electron density ratio in the saturation stage. It is shown that the effect of the ion compensation on the voltage depression caused by the beam space charge field can cause significant changes in the efficiency of gyrotron operation and, in some cases, even result in the break of oscillations.

Revisiting perceptual compensation for effects of reverberation in speech identifcation

DEFF Research Database (Denmark)

Nielsen, Jens Bo; Dau, Torsten

2010-01-01

Listeners were given the task to identify the stop-consonant [t] in the test-word "stir" when the word was embedded in a carrier sentence. Reverberation was added to the test-word, but not to the carrier, and the ability to identify the [t] decreased because the amplitude modulations associated...... with the [t] were smeared. When a similar amount of reverberation was also added to the carrier sentence, the listeners' ability to identify the stop-consonant was restored. This phenomenon has in previous research been considered as evidence for an extrinsic compensation mechanism for reverberation...... an interference effect that impedes the identification of the stop-consonant. These findings raise doubts about the existence of the compensation mechanism....

Compensation and wellness: a conflict for veterans' health.

Science.gov (United States)

Ellis, Niki; Mackenzie, Alison; Mobbs, Robyn

2008-05-01

In Australia greater attention is being given to health determinants, and the dominance of treatment in health policy and budgets is giving away some ground to prevention, health promotion, rehabilitation and disability management. This creates a dilemma for compensation systems: should the inclusion criteria be broadened to match the new thinking or should a narrower definition of "disease, injury or death" be retained? This issue is explored in the context of war syndromes among veterans. While veterans experience symptoms more frequently and more severely than military and community controls, their patterns of symptoms are not unique. Current compensation and benefit programs can create iatrogenic effects. It is concluded that compensation systems should be kept as safety nets while resources are provided to improve the capacity of primary health care caregivers, community organisations and veterans with war syndromes and their families to better deal with these problems. Adapting compensation systems to promote wellness through self-management health partnerships is one way of directing resources to individuals and their families. Action research at the community level with veterans, their families, their organisations, primary health care organisations, policy makers and researchers would allow this sector to work out the best way to apply existing efficacious tools to these modern health problems.

Essays on executive equity-based compensation and equity ownership

OpenAIRE

Elsilä, A. (Anna)

2015-01-01

Abstract A major proposition of the agency theory is that the conflict of interests between an agent and a principal is reduced when the agent’s wealth and compensation are tied to the performance of the firm. Apart from the direct predicted relation to corporate performance, compensating managers with equity instruments has implications for corporate risk-taking and payout policy choices. Additionally, equity-based compensation practices are to a large extent shaped by institutional facto...

Theoretical Study of Watershed Eco-Compensation Standards

Science.gov (United States)

Yan, Dandan; Fu, Yicheng; Liu, Biu; Sha, Jinxia

2018-01-01

Watershed eco-compensation is an effective way to solve conflicts over water allocation and ecological destruction problems in the exploitation of water resources. Despite an increasing interest in the topic, the researches has neglected the effect of water quality and lacked systematic calculation method. In this study we reviewed and analyzed the current literature and proposedatheoretical framework to improve the calculation of co-compensation standard.Considering the perspectives of the river ecosystems, forest ecosystems and wetland ecosystems, the benefit compensation standard was determined by the input-output corresponding relationship. Based on the opportunity costs related to limiting development and water conservation loss, the eco-compensation standard was calculated.In order to eliminate the defects of eco-compensation implementation, the improvement suggestions were proposed for the compensation standard calculation and implementation.

Skew quad compensation at PEP

International Nuclear Information System (INIS)

Murray, J.J.

1977-10-01

Rotational and focal effects of solenoids used in PEP detectors will cause severe perturbations of machine beam optics and must be corrected. Ordinarily this would be accomplished by the addition of compensating solenoids and adjustment of insertion quadrupole strengths. It has been found that an arbitrary cross plane coupling representing the effects of solenoids and/or skew quads in any combination can be synthesized (or compensated) exactly using a quartet of skew quads combined with other erect transport elements in a wide variety of configurations. Specific skew quad compensating systems for PEP have been designed and are under study by PEP staff. So far no fundamental flaws have been discovered. In view of that, PEP management has tentatively authorized the use of such a system in the PEP-4, PEP-9 experiments and proposes to leave the question open ''without prejudice'' for other experiments. Use of skew quad compensation involves an imponderable risk, of course, simply because the method is new and untested. But in addition to providing the only known method for dealing with skew quad perturbations, skew quad compensation, as an alternate to compensating solenoids, promises to be much cheaper, to require much less power and to occupy much less space in the IR's. The purpose of this note is to inform potential users of the foregoing situation and to explain skew quad compensation more fully. 2 refs., 1 fig., 1 tab

Active Surface Compensation for Large Radio Telescope Antennas

Directory of Open Access Journals (Sweden)

Congsi Wang

2018-01-01

Full Text Available With the development of radio telescope antennas with large apertures, high gain, and wide frequency bands, compensation methods, such as mechanical or electronic compensation, are obviously essential to ensure the electrical performance of antennas that work in complex environments. Since traditional compensation methods can only adjust antenna pointing but not the surface accuracy, which are limited for obtaining high surface precision and aperture efficiency, active surface adjustment has become an indispensable tool in this field. Therefore, the development process of electrical performance compensation methods for radio telescope antennas is introduced. Further, a series of analyses of the five key technologies of active surface adjustment is presented. Then, four typical large antennas that have been designed with active main reflector technology are presented and compared. Finally, future research directions and suggestions for reflector antenna compensation methods based on active surface adjustment are presented.

Direction-dependent waist-shift-difference of Gaussian beam in a multiple-pass zigzag slab amplifier and geometrical optics compensation method.

Science.gov (United States)

Li, Zhaoyang; Kurita, Takashi; Miyanaga, Noriaki

2017-10-20

Zigzag and non-zigzag beam waist shifts in a multiple-pass zigzag slab amplifier are investigated based on the propagation of a Gaussian beam. Different incident angles in the zigzag and non-zigzag planes would introduce a direction-dependent waist-shift-difference, which distorts the beam quality in both the near- and far-fields. The theoretical model and analytical expressions of this phenomenon are presented, and intensity distributions in the two orthogonal planes are simulated and compared. A geometrical optics compensation method by a beam with 90° rotation is proposed, which not only could correct the direction-dependent waist-shift-difference but also possibly average the traditional thermally induced wavefront-distortion-difference between the horizontal and vertical beam directions.

Beam-pointing error compensation method of phased array radar seeker with phantom-bit technology

Directory of Open Access Journals (Sweden)

Qiuqiu WEN

2017-06-01

Full Text Available A phased array radar seeker (PARS must be able to effectively decouple body motion and accurately extract the line-of-sight (LOS rate for target missile tracking. In this study, the real-time two-channel beam pointing error (BPE compensation method of PARS for LOS rate extraction is designed. The PARS discrete beam motion principium is analyzed, and the mathematical model of beam scanning control is finished. According to the principle of the antenna element shift phase, both the antenna element shift phase law and the causes of beam-pointing error under phantom-bit conditions are analyzed, and the effect of BPE caused by phantom-bit technology (PBT on the extraction accuracy of the LOS rate is examined. A compensation method is given, which includes coordinate transforms, beam angle margin compensation, and detector dislocation angle calculation. When the method is used, the beam angle margin in the pitch and yaw directions is calculated to reduce the effect of the missile body disturbance and to improve LOS rate extraction precision by compensating for the detector dislocation angle. The simulation results validate the proposed method.

Directive concerning compensation payable for reasons of equity for loss incurred with certain vegetable species (Directive on equitableness, vegetables)

International Nuclear Information System (INIS)

Anon.

1986-01-01

For damage in the field of agriculture caused by the Chernobyl reactor accident which is not within the scope of the Atomic Energy Act, but to be treated under the Farming Law, compensation is paid ex gratia, for reasons of equity. Compensation is paid for loss incurred by the 31st of May 1986 at the latest, as a result of decisions or recommendations issued by the competent public authorities, with reference to the following vegetables: Celery, broccoli, Chinese cabbage, savoy cabbage, onions, kohlrabi, parsley, little radish, radish, rhubarb, chives, white cabbage, herbs cultivated like vegetables for large-scale sale. (orig./HP) [de

Effects of weightlessness, gravity compensation and radiation on the flour beetle, Tribolium confusum

International Nuclear Information System (INIS)

Yang, C.H.; Silver, I.L.; Tobias, C.A.

1975-10-01

Tribolium confusum, the flour beetle; was chosen as a test organism for determination of possible synergistic effects of radiation and space environment in the inertial flight of Biosatellite-II. The organism subjected to weightlessness and radiation during the flight exhibited greater than expected wing abnormalities. However, a postflight vibration control experiment produced anomalous results, and some doubt remained with respect to assigning weightlessness as the sole cause of the increased wing abnormalities. Results are reported from experiments performed on the interaction of gravity compensation, radiation, and Tribolium development. It was found that gravity compensation together with heavy ion irradiation did not cause more wing abnormalities than those caused by radiation alone. However, radiation and gravity compensation plus high temperature did cause an increased percentage of wing abnormalities. Two possible reasons are discussed

Analysis of Faraday Mirror in Auto-Compensating Quantum Key Distribution

International Nuclear Information System (INIS)

Wei Ke-Jin; Ma Hai-Qiang; Li Rui-Xue; Zhu Wu; Liu Hong-Wei; Zhang Yong; Jiao Rong-Zhen

2015-01-01

The ‘plug and play’ quantum key distribution system is the most stable and the earliest commercial system in the quantum communication field. Jones matrix and Jones calculus are widely used in the analysis of this system and the improved version, which is called the auto-compensating quantum key distribution system. Unfortunately, existing analysis has two drawbacks: only the auto-compensating process is analyzed and existing systems do not fully consider laser phase affected by a Faraday mirror (FM). In this work, we present a detailed analysis of the output of light pulse transmitting in a plug and play quantum key distribution system that contains only an FM, by Jones calculus. A similar analysis is made to a home-made auto-compensating system which contains two FMs to compensate for environmental effects. More importantly, we show that theoretical and experimental results are different in the plug and play interferometric setup due to the fact that a conventional Jones matrix of FM neglected an additional phase π on alternative polarization direction. To resolve the above problem, we give a new Jones matrix of an FM according to the coordinate rotation. This new Jones matrix not only resolves the above contradiction in the plug and play interferometric setup, but also is suitable for the previous analyses about auto-compensating quantum key distribution. (paper)

Disturbance estimation and compensation for planar motors on the long-stroke stage of a wafer stage

Directory of Open Access Journals (Sweden)

Bizhong Xia

2015-04-01

Full Text Available This article presents a data-based method to estimate and compensate low-frequency disturbance in planar motors on the long-stroke stage of a wafer stage, which is a typical multiple-input multiple-output system. First, a data-based method is introduced to decouple the multiple-input multiple-output system into multi-single-input single-output system, which is crucial for the design of controller and the correction of disturbance estimation in the scanning direction. Second, dominant low-frequency disturbances in the long-stroke stage are analyzed. Third, estimation and compensation method under moving condition is proposed. The compensation method is based on three feedforward tables, and the tables are indexed by trajectory parameters, including velocity and position instead of time in the iterative learning control method. Finally, experiments are performed on the long-stroke stage of a wafer stage to verify the proposed method. Experimental results show that the proposed method can effectively improve the servo performance by reducing the tracking errors by nearly 1/2 in the forward direction and 1/3 in the backward direction and lowering error difference between the forward and backward directions from 5.1 to 1.2 µm.

No-Reference Stereoscopic IQA Approach: From Nonlinear Effect to Parallax Compensation

Directory of Open Access Journals (Sweden)

Ke Gu

2012-01-01

Full Text Available The last decade has seen a booming of the applications of stereoscopic images/videos and the corresponding technologies, such as 3D modeling, reconstruction, and disparity estimation. However, only a very limited number of stereoscopic image quality assessment metrics was proposed through the years. In this paper, we propose a new no-reference stereoscopic image quality assessment algorithm based on the nonlinear additive model, ocular dominance model, and saliency based parallax compensation. Our studies using the Toyama database result in three valuable findings. First, quality of the stereoscopic image has a nonlinear relationship with a direct summation of two monoscopic image qualities. Second, it is a rational assumption that the right-eye response has the higher impact on the stereoscopic image quality, which is based on a sampling survey in the ocular dominance research. Third, the saliency based parallax compensation, resulted from different stereoscopic image contents, is considerably valid to improve the prediction performance of image quality metrics. Experimental results confirm that our proposed stereoscopic image quality assessment paradigm has superior prediction accuracy as compared to state-of-the-art competitors.

A direct-conversion WLAN transceiver baseband with DC offset compensation and carrier leakage reduction

Energy Technology Data Exchange (ETDEWEB)

Yuan Fang; Yan Jun; Ma Heping; Shi Yin [Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Foster, Dai Fa, E-mail: fyuan@sci-inc.com.c [Department of Electrical and Computer Engineering, Auburn University, Auburn, AL 36849-5201 (United States)

2010-10-15

A dual-band direct-conversion WLAN transceiver baseband compliant with the IEEE 802.11a/b/g standards is described. Several critical techniques for receiver DC offset compensation and transmitter carrier leakage rejection calibration are presented that enable the direct-conversion architecture to meet all WLAN specifications. The receiver baseband VGA provides 62 dB gain range with steps of 2 dB and a DC offset cancellation circuit is introduced to remove the offset from layout and self-mixing. The calibration loop achieves constant high-pass pole when gain changes; and a fast response time by programming the pole to 1 MHz during preamble and to 30 kHz during receiving data. The transmitter baseband employs an auto-calibration loop with on-chip AD and DA to suppress the carrier leakage, and AD can be powered down after calibration to save power consumption. The chip consumes 17.52 mA for RX baseband VGA and DCOC, and 8.3 mA for TX carrier leakage calibration (5.88 mA after calibration) from 2.85 V supply. Implemented in a 0.35 {mu}m SiGe technology, they occupy 0.68 mm{sup 2} and 0.18 mm{sup 2} die size respectively. (semiconductor integrated circuits)

Study on the compensation of electron beam space charge in facilittes with electron cooling

International Nuclear Information System (INIS)

Dikanskij, N.S.; Kudelajnen, V.I.; Parkhomchuk, V.V.; Pestrikov, D.V.

1981-01-01

The results of experimental investigations of a compensated electron beam on the NAP-M facility are presented. The electron beam is compensated by electrostatic plugs preventing ion leakage along the beam. Cut-off electrodes have the shape of cutted cylinders encircling the electron beam. To eliminate electron accumulation around the plugs one of the electrodes has a zero potential, which results in formation of an transverse electric field causing ionization electron drift in the transverse direction to the electric and magnetic fields. The effect of wave damping, in the compensated beam is observed, that demonstrates the possibility of gaining great current densities in long compensated beams necessary for antiproton storage. For the NAP-M at the 10 10 cm/s electron velocity, 300 cm length of ion column, and 1 kOe field intensity the threshold beam current density is 0.96 A/cm 2 [ru

Compensation of dogleg effect in Fermilab Booster

CERN Document Server

Xiao Biao Huang

2003-01-01

The edge focusing of dogleg magnets in Fermilab Booster has been causing severe distortion to the horizontal linear optics. The doglegs are vertical rectangular bends, therefore the vertical edge focusing is canceled by body focusing and the overall effect is focusing in the horizontal plane. The maximum horizontal beta function is changed from 7m to 46.9m and maximum dispersion from 3.19m to 6.14m. Beam size increases accordingly. This is believed to be one of the major reasons of beam loss. In this technote we demonstrate that this effect can be effectively corrected with Booster's quadrupole correctors in short straight sections (QS). There are 24 QS correctors which can alter horizontal linear optics with negligible perturbation to the vertical plane. The currents of correctors are determined by harmonic compensation, i.e., cancellation of dogleg's harmonics that are responsible for the distortion with that of QS correctors. By considering a few leading harmonics, the ideal lattice can be partly restored....

Compensation of F0 and formant frequencies in a real-time pitch-perturbation paradigm

DEFF Research Database (Denmark)

Eckey, Andreas; MacDonald, Ewen

2015-01-01

While producing speech, talkers monitor both somatosensory and auditory feedback. Many studies have demonstrated that if auditory feedback is manipulated in real-time (e.g., using an effects processor to shift the frequency spectrum), subjects compensate by modifying their F0 in the direction opp...

Losses compensation; Compensation des pertes

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

One mission of RTE (Electric Power Transportation), is to watch over the losses compensation resulting from the power transport on the electric power network. Since january 2001, RTE makes good the electric losses by the purchase of energy. To choose the marketers, a consultation has been realized by RTE. This document presents the rules concerning these losses compensation. (A.L.B.)

Climate change and compensation

DEFF Research Database (Denmark)

Jensen, Karsten Klint; Flanagan, Tine Bech

2013-01-01

This paper presents a case for compensation of actual harm from climate change in the poorest countries. First, it is shown that climate change threatens to reverse the fight to eradicate poverty. Secondly, it is shown how the problems raised in the literature for compensation to some extent...... are based on misconceptions and do not apply to compensation of present actual harm. Finally, two arguments are presented to the effect that, in so far as developed countries accept a major commitment to mitigate climate change, they should also accept a commitment to address or compensate actual harm from...... climate change. The first argument appeals to the principle that if it is an injustice to cause risk of incurring harm in the future, then it is also an injustice to cause a similar harm now. The second argument appeals to the principle that if there is moral reason to reduce the risk of specific harms...

Environmental change, phenotypic plasticity, and genetic compensation.

Science.gov (United States)

Grether, Gregory F

2005-10-01

When a species encounters novel environmental conditions, some phenotypic characters may develop differently than in the ancestral environment. Most environmental perturbations of development are likely to reduce fitness, and thus selection would usually be expected to favor genetic changes that restore the ancestral phenotype. I propose the term "genetic compensation" to refer to this form of adaptive evolution. Genetic compensation is a subset of genetic accommodation and the reverse of genetic assimilation. When genetic compensation has occurred along a spatial environmental gradient, the mean trait values of populations in different environments may be more similar in the field than when representatives of the same populations are raised in a common environment (i.e., countergradient variation). If compensation is complete, genetic divergence between populations may be cryptic, that is, not detectable in the field. Here I apply the concept of genetic compensation to three examples involving carotenoid-based sexual coloration and then use these and other examples to discuss the concept in a broader context. I show that genetic compensation may lead to a cryptic form of reproductive isolation between populations evolving in different environments, may explain some puzzling cases in which heritable traits exposed to strong directional selection fail to show the expected evolutionary response, and may complicate efforts to monitor populations for signs of environmental deterioration.

Study on APD real time compensation methods of laser Detection system

International Nuclear Information System (INIS)

Feng Ying; Zhang He; Zhang Xiangjin; Liu Kun

2011-01-01

With the monochromatic and the directional capability of the laser, laser detection system is confidential in anti-jamming. Detection accuracy is improved significantly as the result of laser's good orientation ability. Sensitivity is enhanced as laser's high-brightness characteristic. With the development of laser technology and laser devices, laser detections are developed both in civilian and military areas. In the military field, laser detection system has been widely applied in various types of tactical missiles, the technique is more mature. Because photo detectors receive the backscattering echo signal of target in laser detection system, they are required sensitive enough to weak signal. With APD's salient features of high sensitivity, rapid response speed, high response frequency and low noise equivalent power, etc.; PIN is replaced by APD to improve sensitivity of laser detection system in recent years. The signal magnification is inadequate in laser detection system, the detector output is usually amplified by multistage amplifiers. And then the system noise includes detector noise and latter amplifiers noise. With its high internal gain, APD becomes the primary noise source of receiving system. This point can be attested by analyzing the transfer function of laser detection system receiver. To ensure the system detecting ability, APD noise must be mitigated as low as possible. According to a large number of experiments, the power signal-to-noise (SNR) and the best multiplication factor of APD are mostly affected by background radiation and temperature. In order to make APD operate at state of the best multiplication factor, the optimum bias must be selected due to the actual operating circumstance. Therefore, APD realtime compensation must be adopted. The existing APD compensation includes the constant false alarm rate compensation, the noise compensation and the temperature compensation. The features of these compensations are obtained by analyzing

Study on APD real time compensation methods of laser Detection system

Energy Technology Data Exchange (ETDEWEB)

Feng Ying; Zhang He; Zhang Xiangjin; Liu Kun, E-mail: fy_caimi@163.com [ZNDY of Ministerial Key Laboratory, Nanjing University of Science and Technology, Nanjing 210094 (China)

2011-02-01

With the monochromatic and the directional capability of the laser, laser detection system is confidential in anti-jamming. Detection accuracy is improved significantly as the result of laser's good orientation ability. Sensitivity is enhanced as laser's high-brightness characteristic. With the development of laser technology and laser devices, laser detections are developed both in civilian and military areas. In the military field, laser detection system has been widely applied in various types of tactical missiles, the technique is more mature. Because photo detectors receive the backscattering echo signal of target in laser detection system, they are required sensitive enough to weak signal. With APD's salient features of high sensitivity, rapid response speed, high response frequency and low noise equivalent power, etc.; PIN is replaced by APD to improve sensitivity of laser detection system in recent years. The signal magnification is inadequate in laser detection system, the detector output is usually amplified by multistage amplifiers. And then the system noise includes detector noise and latter amplifiers noise. With its high internal gain, APD becomes the primary noise source of receiving system. This point can be attested by analyzing the transfer function of laser detection system receiver. To ensure the system detecting ability, APD noise must be mitigated as low as possible. According to a large number of experiments, the power signal-to-noise (SNR) and the best multiplication factor of APD are mostly affected by background radiation and temperature. In order to make APD operate at state of the best multiplication factor, the optimum bias must be selected due to the actual operating circumstance. Therefore, APD realtime compensation must be adopted. The existing APD compensation includes the constant false alarm rate compensation, the noise compensation and the temperature compensation. The features of these compensations are obtained

Study on APD real time compensation methods of laser Detection system

Science.gov (United States)

Ying, Feng; He, Zhang; Xiangjin, Zhang; Kun, Liu

2011-02-01

With the monochromatic and the directional capability of the laser, laser detection system is confidential in anti-jamming. Detection accuracy is improved significantly as the result of laser's good orientation ability. Sensitivity is enhanced as laser's high-brightness characteristic. With the development of laser technology and laser devices, laser detections are developed both in civilian and military areas. In the military field, laser detection system has been widely applied in various types of tactical missiles, the technique is more mature. Because photo detectors receive the backscattering echo signal of target in laser detection system, they are required sensitive enough to weak signal. With APD's salient features of high sensitivity, rapid response speed, high response frequency and low noise equivalent power, etc.; PIN is replaced by APD to improve sensitivity of laser detection system in recent years. The signal magnification is inadequate in laser detection system, the detector output is usually amplified by multistage amplifiers. And then the system noise includes detector noise and latter amplifiers noise. With its high internal gain, APD becomes the primary noise source of receiving system. This point can be attested by analyzing the transfer function of laser detection system receiver. To ensure the system detecting ability, APD noise must be mitigated as low as possible. According to a large number of experiments, the power signal-to-noise (SNR) and the best multiplication factor of APD are mostly affected by background radiation and temperature. In order to make APD operate at state of the best multiplication factor, the optimum bias must be selected due to the actual operating circumstance. Therefore, APD realtime compensation must be adopted. The existing APD compensation includes the constant false alarm rate compensation, the noise compensation and the temperature compensation. The features of these compensations are obtained by analyzing

THE EFFECT OF COMPENSATION, LEADERSHIP AND ORGANIZATIONAL CULTURE THROUGH WORK MOTIVATION ON EMPLOYEE PERFORMANCE

Directory of Open Access Journals (Sweden)

Djoko Setyo Widodo

2017-12-01

Full Text Available This study aims to examine the effect of compensation, leadership and organizational culture through work motivation on employee performance. This study uses a quantitative method by distributing questionnaires to employees in the conventional banking environment in Bekasi. The research sample is determined by simple random sampling and the technique analysis is SEM analysis with AMOS ver. 21. This study shows positive and significant results partially from the effect of variable compensation, leadership, organizational culture and motivation on employee performance. On the other hand, the study also find that organizational culture has no effect on work motivation. Based on the results of this study conclude that all hypothesis are supported but one hypotheses that examine the influence of organizational culture has no effect on work motivation.

Do compensation processes impair mental health? A meta-analysis.

Science.gov (United States)

Elbers, Nieke A; Hulst, Liesbeth; Cuijpers, Pim; Akkermans, Arno J; Bruinvels, David J

2013-05-01

Victims who are involved in a compensation processes generally have more health complaints compared to victims who are not involved in a compensation process. Previous research regarding the effect of compensation processes has concentrated on the effect on physical health. This meta-analysis focuses on the effect of compensation processes on mental health. Prospective cohort studies addressing compensation and mental health after traffic accidents, occupational accidents or medical errors were identified using PubMed, EMBASE, PsycInfo, CINAHL, and the Cochrane Library. Relevant studies published between January 1966 and 10 June 2011 were selected for inclusion. Ten studies were included. The first finding was that the compensation group already had higher mental health complaints at baseline compared to the non-compensation group (standardised mean difference (SMD)=-0.38; 95% confidence interval (CI) -0.66 to -0.10; p=.01). The second finding was that mental health between baseline and post measurement improved less in the compensation group compared to the non-compensation group (SMD=-0.35; 95% CI -0.70 to -0.01; p=.05). However, the quality of evidence was limited, mainly because of low quality study design and heterogeneity. Being involved in a compensation process is associated with higher mental health complaints but three-quarters of the difference appeared to be already present at baseline. The findings of this study should be interpreted with caution because of the limited quality of evidence. The difference at baseline may be explained by a selection bias or more anger and blame about the accident in the compensation group. The difference between baseline and follow-up may be explained by secondary gain and secondary victimisation. Future research should involve assessment of exposure to compensation processes, should analyse and correct for baseline differences, and could examine the effect of time, compensation scheme design, and claim settlement on

Creative compensation

International Nuclear Information System (INIS)

Coll, D.

1994-01-01

A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs

Creative compensation

Energy Technology Data Exchange (ETDEWEB)

Coll, D

1994-09-19

A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs.

Sales compensation governance: the last frontier of corporate reform.

Science.gov (United States)

Gundy, Peter R; Gaeta, Elizabeth C

2004-01-01

The area of sales compensation has remained relatively untouched by recent pressures for compensation reform. This article highlights some of the ways that sales organizations stumble in managing their compensation programs, and why it takes more than a simple tactical fix to address these problems effectively. The authors describe a more structured governance framework that not only identifies and resolves key sales compensation issues, but ultimately safeguards the effectiveness and financial integrity of the sales organization itself.

Procedural justice and quality of life in compensation processes.

Science.gov (United States)

Elbers, Nieke A; Akkermans, Arno J; Cuijpers, Pim; Bruinvels, David J

2013-11-01

There is considerable evidence that being involved in compensation processes has a negative impact on claimants' health. Previous studies suggested that this negative effect is caused by a stressful compensation process: claimants suffered from a lack of communication, a lack of information, and feelings of distrust. However, these rather qualitative findings have not been quantitatively investigated yet. This observational study aimed to fill this gap of knowledge, investigating the claimants' perceived fairness of the compensation process, the provided information, and the interaction with lawyers and insurance companies, in relation to the claimants' quality of life. Participants were individuals injured in traffic accidents, older than 18 years, who were involved in a compensation process in the Netherlands. They were recruited by three claims settlement offices. Outcome measures were procedural, interactional, and informational justice, and quality of life. Participants (n=176) perceived the interaction with lawyers to be fairer than the interaction with insurance companies (pquality of life (rs=.22, p=.004). The finding that the interaction with insurance companies was considered less fair than the interaction with lawyers may imply that insurers could improve their interaction with claimants, e.g. by communicating more directly. The result that claimants with mild injuries and with trunk/back injuries considered the compensation process to be less fair than those with respectively severe injuries and injuries to other body parts suggests that especially the former two require an attentive treatment. Finally, the fact that procedural justice was positively correlated with quality of life could implicate that it is possible to improve claimants' health in compensation processes by enhancing procedural justice, e.g. by increasing the ability for claimants to express their views and feelings and by involving claimants in the decision-making process. Copyright �

Characteristics of a laser beam produced by using thermal lensing effect compensation in a fiber-coupled laser-diode-pumped Nd:YAG ceramic laser

International Nuclear Information System (INIS)

Kim, Duck-Lae; Kim, Byung-Tai

2010-01-01

The characteristics of a laser beam produced by using thermal lensing effect compensation in a fiber-coupled laser-diode Nd:YAG ceramic laser were investigated. The thermal lensing effect was compensated for by using a compensator, which was 25 mm away from the laser rod, with a focal length of 30 mm and an effective clear aperture of 22 mm. Using a compensator, the divergence and the beam propagation factor M 2 of the output beam were 5.5 mrad and 2.4, respectively, under a pump power of 12W. The high-frequency components in the compensated laser beam were removed.

The effect of weekend and holiday sleep compensation on childhood overweight and obesity.

Science.gov (United States)

Wing, Yun Kwok; Li, Shirley Xin; Li, Albert Martin; Zhang, Jihui; Kong, Alice Pik Shan

2009-11-01

A growing trend in childhood sleep habits is to compensate for the weekday sleep deficit by longer weekend and holiday sleep duration. We aimed to investigate the effect of weekend/holiday sleep compensation in relation to childhood overweight and obesity. This is a community-based cross-sectional study with 5159 children (49.6% boys), mean age of 9.25 years (SD: 1.78), from 13 primary schools in Hong Kong. Data on sleep patterns, lifestyle, body weight, and height of children were obtained from questionnaires. Sleep durations during weekdays, weekends, and holidays were predictor variables. BMI z scores and obesity/overweight status were the outcome measures. Children slept significantly longer during holidays (mean [SD]: 10.20 (0.92) hours) and weekends (school terms) (10.07 [0.93] hours) than during school weekdays (9.18 [0.95] hours). Children with shorter sleep duration had higher BMI z scores regardless of the sleep parameters used in the analysis. Among children who slept holidays had significantly increased risk of overweight/obesity compared with those children with sleep compensation (odds ratios: 2.59 [95% confidence interval: 1.22-5.48] and 2.32 [95% confidence interval: 1.00-5.53], respectively). There was a prominent difference in sleep duration between weekdays and weekends/holidays among school children. Short sleep duration was associated with higher BMI, but compensation of sleep during weekends/holidays may partly ameliorate the risk of childhood overweight/obesity. Further prospective and interventional study is needed to delineate the risk-benefit effect of these increasingly common sleep habits among children and adolescents.

The effects of performance measurement and compensation on motivation: An empirical study

NARCIS (Netherlands)

van Herpen, M.; van Praag, C.M.; Cools, K.

2003-01-01

The design and implementation of a performance measurement and compensation system can strongly affect the motivation of employees. Building on economic and psychological theory this study develops a conceptual model that is used to empirically test this effect. Our survey results demonstrate a

The Effect of Disability Insurance on Health Investment: Evidence from the Veterans Benefits Administration's Disability Compensation Program

Science.gov (United States)

Singleton, Perry

2009-01-01

I examine whether individuals respond to monetary incentives to detect latent medical conditions. The effect is identified by a policy that deemed diabetes associated with herbicide exposure a compensable disability under the Veterans Benefits Administration's Disability Compensation program. Since a diagnosis is a requisite for benefit…

Global patterns and trends in human-wildlife conflict compensation.

Science.gov (United States)

Ravenelle, Jeremy; Nyhus, Philip J

2017-12-01

Human-wildlife conflict is a major conservation challenge, and compensation for wildlife damage is a widely used economic tool to mitigate this conflict. The effectiveness of this management tool is widely debated. The relative importance of factors associated with compensation success is unclear, and little is known about global geographic or taxonomic differences in the application of compensation programs. We reviewed research on wildlife-damage compensation to determine geographic and taxonomic gaps, analyze patterns of positive and negative comments related to compensation, and assess the relative magnitude of global compensation payments. We analyzed 288 publications referencing wildlife compensation and identified 138 unique compensation programs. These publications reported US$222 million (adjusted for inflation) spent on compensation in 50 countries since 1980. Europeans published the most articles, and compensation funding was highest in Europe, where depredation by wolves and bears was the most frequently compensated damage. Authors of the publications we reviewed made twice as many negative comments as positive comments about compensation. Three-quarters of the negative comments related to program administration. Conversely, three-quarters of the positive comments related to program outcomes. The 3 most common suggestions to improve compensation programs included requiring claimants to employ damage-prevention practices, such as improving livestock husbandry or fencing of crops to receive compensation (n = 25, 15%); modifying ex post compensation schemes to some form of outcome-based performance payment (n = 21, 12%); and altering programs to make compensation payments more quickly (n = 14, 8%). We suggest that further understanding of the strengths and weaknesses of compensation as a conflict-mitigation tool will require more systematic evaluation of the factors driving these opinions and that differentiating process and outcomes and understanding

A nonlinearity compensation method for a matrix converter drive

DEFF Research Database (Denmark)

Lee, Kyo-Beum; Blaabjerg, Frede

2005-01-01

converter model using the direction of current. The proposed method does not need any additional hardware or complicated software and it is easy to realize by applying the algorithm to the conventional vector control. The proposed compensation method is applied for high-performance induction motor drives...... using a 3-kW matrix converter system without a speed sensor. Experimental results show the proposed method provides good compensating characteristics....

Do Compensation Processes Impair Mental Health? A Meta-Analysis Injury

NARCIS (Netherlands)

Elbers, N.A.; Hulst, J.E.; Cuijpers, P.; Akkermans, A.J.; Bruinvels, D.J.

2013-01-01

Background: Victims who are involved in a compensation processes generally have more health complaints compared to victims who are not involved in a compensation process. Previous research regarding the effect of compensation processes has concentrated on the effect on physical health. This

Test and simulation of dynamic phase compensation from Mita-Teknik A/S

Energy Technology Data Exchange (ETDEWEB)

Soerensen, P.; Iov, F.; Blaabjerg, F.; Skaarup, J.

2004-03-01

This report describes the test of a dynamic phase compensation unit for a wind turbine with directly connected induction generators. The compensation unit is based on thyristor switched capacitors, where conventional wind turbine compensations use mechanical contactors to switch the capacitors. The influence on power quality analysed, and influence on component lifetime is discussed. Besides, simulation models in Matlab/Simulink are presented, including a flicker meter model. (au)

Compensation effect in H 2 permeation kinetics of PdAg membranes

KAUST Repository

Zeng, Gaofeng

2012-08-30

Knowledge about the (inter)dependence of permeation kinetic parameters on the stoichiometry of H 2-selective alloys is still rudimentary, although uncovering the underlying systematic correlations will greatly facilitate current efforts into the design of novel high-performance H 2 separation membranes. Permeation measurements with carefully engineered, 2-7 μm thick supported Pd 100-xAg x membranes reveal that the activation energy and pre-exponential factor of H 2 permeation laws vary systematically with alloy composition, and both kinetic parameters are strongly correlated for x ≤ 50. We show that this permeation kinetic compensation effect corresponds well with similar correlations in the hydrogen solution thermodynamics and diffusion kinetics of PdAg alloys that govern H 2 permeation rates. This effect enables the consistent description of permeation characteristics over wide temperature and alloy stoichiometry ranges, whereas hydrogen solution thermodynamics may play a role, too, as a yet unrecognized source of kinetic compensation in, for example, H 2-involving reactions over metal catalysts or hydrogenation/ dehydrogenation of hydrogen storage materials. © 2012 American Chemical Society.

Modified compensation algorithm of lever-arm effect and flexural deformation for polar shipborne transfer alignment based on improved adaptive Kalman filter

International Nuclear Information System (INIS)

Wang, Tongda; Cheng, Jianhua; Guan, Dongxue; Kang, Yingyao; Zhang, Wei

2017-01-01

Due to the lever-arm effect and flexural deformation in the practical application of transfer alignment (TA), the TA performance is decreased. The existing polar TA algorithm only compensates a fixed lever-arm without considering the dynamic lever-arm caused by flexural deformation; traditional non-polar TA algorithms also have some limitations. Thus, the performance of existing compensation algorithms is unsatisfactory. In this paper, a modified compensation algorithm of the lever-arm effect and flexural deformation is proposed to promote the accuracy and speed of the polar TA. On the basis of a dynamic lever-arm model and a noise compensation method for flexural deformation, polar TA equations are derived in grid frames. Based on the velocity-plus-attitude matching method, the filter models of polar TA are designed. An adaptive Kalman filter (AKF) is improved to promote the robustness and accuracy of the system, and then applied to the estimation of the misalignment angles. Simulation and experiment results have demonstrated that the modified compensation algorithm based on the improved AKF for polar TA can effectively compensate the lever-arm effect and flexural deformation, and then improve the accuracy and speed of TA in the polar region. (paper)

Market mechanisms for compensating hazardous work: a critical analysis

International Nuclear Information System (INIS)

Shakow, D.

1984-01-01

Adam Smith's theory that the marketplace can compensate workers for social inequities (i.e., hazards, boredom, etc.) in the work place is applied to the nuclear industry. The author argues that market mechanisms are unlikely to ensure adequate compensation for work-related hazards. He summarizes and critiques the neoclassical compensating-wage hypothesis, then reviews empirical evidence in support of the hypothesis in light of an alternative hypothesis derived from the literature on labor market segmentation. He challenges the assumption of perfect labor mobility and perfect information. A promising direction for further research would be a structural analysis of the emerging market for temporary workers. 13 references, 2 figures

Capital Structure and Managerial Compensation: The Effects of Renumeration Seniority

OpenAIRE

Calcagno, R.; Renneboog, L.D.R.

2004-01-01

We show that the relative seniority of debt and managerial compensation has important implications on the design of remuneration contracts.Whereas the traditional literature assumes that debt is senior to remuneration, we show that this is frequently not the case according to bankruptcy regulation and as observed in practice.We theoretically show that including risky debt changes the incentive to provide the manager with stronger performance-related incentives ("contract substitution" effect)...

Compensation in Swedish infrastructure projects and suggestions on policy improvements

Directory of Open Access Journals (Sweden)

Jesper Persson

2015-07-01

Full Text Available Environmental compensation includes a range of activities intended to counterbalance such negative impacts of development projects that remain in the environment after all preventive and corrective measures have been fully implemented. Sweden, being a member state of the European Union (EU, must implement environmental compensation under EU directives such as the Habitat Directive. However, like in other countries, implementation is not yet widespread in Sweden, and new practices and guidelines remain to be developed both nationally and at European level. This need is all the more urgent considering that the European Commission estimates that, within the EU, about 100,000 hectares of land is converted from its natural state each year. The aim of this paper is to describe current environmental-compensation practices in Swedish road and railway projects and to discuss issues of vital importance to the development of compensation policy, such as what to compensate for, how much, and how. A national inventory was performed, for the first time in Sweden, to identify compensation measures in road and railway projects. Data were collected from a national mailing list including 141 officials at county administrative boards (CABs, internal e-mail correspondence within the Swedish Transport Administration and databases of court decisions. The inventory focused on compensation measures ordered by virtue of the Swedish Environmental Code. In addition, two case studies were carried out to investigate the planning of compensation measures. The results showed that CABs and courts rarely order compensation in infrastructure projects, even though this is possible under Swedish law. Between 1999 and 2012, 37 cases (i.e. permits issued were found for which compensation was ordered. Of these cases, 76% concerned compensation for encroachments on minor habitats such as small ponds and cairns. No CAB ordered compensation for non-protected areas. Compensation ratios

Monetary compensations in climate policy through the lens of a general equilibrium assessment: The case of oil-exporting countries

International Nuclear Information System (INIS)

Waisman, Henri; Rozenberg, Julie; Hourcade, Jean Charles

2013-01-01

This paper investigates the compensations that major oil producers have claimed for since the Kyoto Protocol in order to alleviate the adverse impacts of climate policy on their economies. The amount of these adverse impacts is assessed through a general equilibrium model which endogenizes both the reduction of oil exportation revenues under international climate policy and the macroeconomic effect of carbon pricing on Middle-East's economy. We show that compensating the drop of exportation revenues does not offset GDP and welfare losses because of the time profile of the general equilibrium effects. When considering instead compensation based on GDP losses, the effectiveness of monetary transfers proves to be drastically limited by general equilibrium effects in opened economies. The main channels of this efficiency gap are investigated and its magnitude proves to be conditional upon strategic and policy choices of the Middle-East. This leads us to suggest that other means than direct monetary compensating transfers should be discussed to engage the Middle-East in climate policies. - Highlights: • We endogenize the interplay between climate policy, oil markets and the macroeconomy. • We quantify the transfers to compensate climate policy losses in oil-exporting countries. • We assess the general equilibrium effect of monetary transfers in opened economies. • The macroeconomic efficiency of transfers is altered by general equilibrium effects. • Monetary compensation schemes are not efficient for oil exporters in climate policy

Effects of Proprioceptive Neuromuscular Facilitation Stretching and Kinesiology Taping on Pelvic Compensation During Double-Knee Extension

Directory of Open Access Journals (Sweden)

Lee Seung-Woong

2015-12-01

Full Text Available Shortened hamstrings are likely to restrict the anterior pelvic tilt and induce a slumped posture due to the posterior pelvic tilt. This study was conducted to compare the effects of proprioceptive neuromuscular facilitation (PNF stretching and modified anterior pelvic tilt taping (APTT on hamstring shortness-associated pelvic compensation while executing seated double-knee extension. Male college students (28 healthy young adults; mean age: 21.4 ± 2.1 years with hamstring shortness were recruited as study subjects and randomly assigned to either the PNF stretching group (control group or the APTT group (experimental group. In all the subjects, changes in the movement distance of the centre of gluteal pressure (COGP as well as rectus abdominis (RA and semitendinosus (SEM muscle activities were measured during seated double-knee extension while the respective intervention method was applied. Both groups showed significant decreases in COGP distance and RA muscle activity compared with their respective baseline values (p < 0.05, however, no significant changes were observed in SEM muscle activity. We can infer that not only a direct intervention on the hamstring, such as PNF stretching, but also a modified APTT-mediated pelvic intervention may be used as a method for reducing pelvic compensation induced by hamstring shortness.

Health Insurance Costs and Employee Compensation: Evidence from the National Compensation Survey.

Science.gov (United States)

Anand, Priyanka

2017-12-01

This paper examines the relationship between rising health insurance costs and employee compensation. I estimate the extent to which total compensation decreases with a rise in health insurance costs and decompose these changes in compensation into adjustments in wages, non-health fringe benefits, and employee contributions to health insurance premiums. I examine this relationship using the National Compensation Survey, a panel dataset on compensation and health insurance for a sample of establishments across the USA. I find that total hourly compensation reduces by $0.52 for each dollar increase in health insurance costs. This reduction in total compensation is primarily in the form of higher employee premium contributions, and there is no evidence of a change in wages and non-health fringe benefits. These findings show that workers are absorbing at least part of the increase in health insurance costs through lower compensation and highlight the importance of examining total compensation, and not just wages, when examining the relationship between health insurance costs and employee compensation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Adaptive Robust Motion Control of Direct-Drive DC Motors with Continuous Friction Compensation

Directory of Open Access Journals (Sweden)

Jianyong Yao

2013-01-01

Full Text Available Uncertainties including the structured and unstructured, especially the nonlinear frictions, always exist in physical servo systems and degrade their tracking accuracy. In this paper, a practical method named adaptive robust controller (ARC is synthesized with a continuous differentiable friction model for high accuracy motion control of a direct-drive dc motor, which results in a continuous control input and thus is more suitable for application. To further reduce the noise sensitivity and improve the tracking accuracy, a desired compensation version of the proposed adaptive robust controller is also developed and its stability is guaranteed by a proper robust law. The proposed controllers not only account for the structured uncertainties (e.g., parametric uncertainties but also for the unstructured uncertainties (e.g., unconsidered nonlinear frictions. Furthermore, the controllers theoretically guarantee a prescribed output tracking transient performance and final tracking accuracy in both structured and unstructured uncertainties while achieving asymptotic output tracking in the absence of unstructured uncertainties, which is very important for high accuracy control of motion systems. Extensive comparative experimental results are obtained to verify the high-performance nature of the proposed control strategies.

Non-Cooperative Bistatic SAR Clock Drift Compensation for Tomographic Acquisitions

Directory of Open Access Journals (Sweden)

Mario Azcueta

2017-10-01

Full Text Available In the last years, an important amount of research has been headed towards the measurement of above-ground forest biomass with polarimetric Synthetic Aperture Radar (SAR tomography techniques. This has motivated the proposal of future bistatic SAR missions, like the recent non-cooperative SAOCOM-CS and PARSIFAL from CONAE and ESA. It is well known that the quality of SAR tomography is directly related to the phase accuracy of the interferometer that, in the case of non-cooperative systems, can be particularly affected by the relative drift between onboard clocks. In this letter, we provide insight on the impact of the clock drift error on bistatic interferometry, as well as propose a correction algorithm to compensate its effect. The accuracy of the compensation is tested on simulated acquisitions over volumetric targets, estimating the final impact on tomographic profiles.

Local governments' roles of the compensation for damage by the Tokai JCO criticality accident

International Nuclear Information System (INIS)

Tanabe, Tomoyuki

2003-01-01

The Tokai JCO criticality accident on September 30, 1999 was the first case to which The Law on Compensation for Nuclear Damage was applied. Although the Law on Compensation for Nuclear Damage formulates the outline of the institutional framework for nuclear third party liability together with operator's insurance scheme, details of actual compensation procedure are not specified. By this reason, the compensation procedure in the Tokai accident had been executed without a concrete legal specification and a precedent. In spite of this situation, the compensation procedure with the accident led to an unexpectedly successful result. We observe the several reasons why the compensation procedure was implemented successfully despite the lack of concrete legal specification and a precedent. One of the reasons is that the local governments, Tokai Village and Ibaraki Prefecture, immediately took the leadership in implementing a temporary regime of compensation procedure without wasting time for waiting national government's directives. Upon practicing this compensation procedure, the local governments implemented the following steps. (1) Initial estimation of the amount and scope of damage. (2) Providing the criteria and heads of damage subject to compensation. (3) Unitary compensation procedure at the local levels. (4) Distribution of emergency payments for the victims. (5) Facilitating compensatory negotiation between the victims and JCO as arbitrator. However, some concerns are also pointed out about the fact that the local government directed the whole procedure without sufficient adjustment with the national government for compensation policy. Among all, in the compensation led by the local governments, it was difficult to guarantee fairness of compensation because victims who are influential on the local government such as industrial associations would have unfairly strong negotiation power in the compensatory negotiation, while the operator being responsible for the

Optical compensation device for chest film radiography

Science.gov (United States)

Gould, Robert G.; Hasegawa, Bruce H.; DeForest, Sherman E.; Schmidt, Gregory W.; Hier, Richard G.

1990-07-01

Although chest radiography is the most commonly performed radiographic examination and one of the most valuable and cost-effective studies in medicine it suffers from relatively high error rates in both missing pathology and false positive interpretations. Detectability of lung nodules and other structures in underpenetrated regions of the chest film can be improved by both exposure and optical compensation but current compensation systems require major capital cost or a significant change in normal clinical practice. A new optical compensation system called the " Intelligent X-Ray Illuminator" (IXI) automatically and virtually instantaneously generates a patient-specific optical unsharp mask that is projected directly on a radiograph. When a radiograph is placed on the IXI which looks much like a conventional viewbox it acquires a low-resolution electronic image of this film from which the film transmission is derived. The transmission information is inverted and blurred in an image processor to form an unsharp mask which is fed into a spatial light modulator (SLM) placed between a light source and the radiograph. The SLM tailors the viewbox luminance by decreasing illumination to underexposed (i. e. transmissive) areas of the radiograph presenting the observer with an optically unsharp-masked image. The IXI uses the original radiograph and will allow it to be viewed on demand with conventional (uniform illumination. Potentially the IXI could introduce the known beneficial aspects of optical unsharp masking into radiology at low capital

Compensated-power differential calorimeter -196 deg. C/400 deg. C

International Nuclear Information System (INIS)

Bonjour, E.; Pierre, J.; Agagliate, S.; Bertrand, P.; Faivre, J.; Lagnier, R.

1967-06-01

A differential calorimetric device of original design is described. Its allows direct measurements of thermal effects (adsorption or release) during a linear rise of temperature. The self compensated power method which is applied by means of a very sensitive control system, gives a direct value of the different heat capacity between the sample and a dummy of it. The detection threshold is about ± 100 micro-watts to ± 250 micro-watts. Applications: - Generally measurements of enthalpy changes of massive or powdered samples. - Measurement of Wigner energy after low temperature irradiation (77 deg. K). - Measurements of energy release in low temperature (77 deg. K) cold worked metals. (authors) [fr

Improving dose homogeneity in head and neck radiotherapy with custom 3-D compensation

International Nuclear Information System (INIS)

Brock, Linda K.; Harari, Paul M.; Sharda, Navneet N.; Paliwal, Bhudatt R.; Kinsella, Timothy J.

1996-01-01

Purpose/Objective: Anatomic contour irregularities and tissue inhomogeneities can lead to significant radiation dose variation across complex treatment volumes. Such dose non-uniformity occurs routinely in radiation of the head and neck (H and N) despite beam shaping with blocks or beam modification with wedges. Small dose variations are amplified by the high total doses delivered (often >70 Gy) which can thereby influence late normal tissue complications as well as tumor control. We have therefore implemented the routine use of 3-D custom tissue compensators for our H and N cancer patients fabricated directly from CT scan contour data obtained in the treatment position. The capacity of such compensators to improve dose uniformity in patients with tumors of the H and N is herein reported. Materials and Methods: Between July 1992 and March 1995, 80 patients receiving H and N radiotherapy had 3-D custom compensators fabricated for their treatment course. Detailed dosimetric records have been reviewed for thirty cases to date (60 custom compensators). Dose uniformity across the treatment volume, peak dose delivery and maximum doses to selected, clinically relevant, anatomic subsites were analyzed and compared with uncompensated and wedged plans. Dose-volume histograms were generated and volumes receiving greater than 5% and 10% of the prescribed dose noted. Phantom dose measurements were performed for compensated fields using a water chamber and were compared to calculated doses in order to evaluate the accuracy of isodoses generated by the Theraplan treatment planning system. Accuracy of the fabrication and positioning of the custom compensators was verified by direct measurement. Results: Custom compensators resulted in an average reduction of dose variance across the treatment volume from 13.8% (7-20%) for the uncompensated plans to 4.5% (2-7%) with the compensators. Wedged plans were variable but on average an 8% (3-15%) dose variance was noted. Maximum doses

Emittance compensation of CW DC-gun photoinjector

International Nuclear Information System (INIS)

Li Peng; Wu Dai; Xu Zhou; Li Ming; Yang Xingfan

2011-01-01

Emittance growth induced by space charge effect is very important, especially for CW DC-gun photoinjector. In this work, the linear space charge force and its effect on electron beam transverse emittance are studied, and the principle and properties of emittance compensation by solenoid are analyzed. The CAEP DC-gun photoinjector with a solenoid is also simulated by code Parmela. Simulated results indicate that the normalized transverse emittance of an 80 pC bunch at the 350 keV DC-gun ex-it is 5.14 mm · mrad. And after compensated by a solenoid, it becomes 1.27 mm · mrad. The emittance of beam is well compensated. (authors)

Optimal compensation for neuron loss

Science.gov (United States)

Barrett, David GT; Denève, Sophie; Machens, Christian K

2016-01-01

The brain has an impressive ability to withstand neural damage. Diseases that kill neurons can go unnoticed for years, and incomplete brain lesions or silencing of neurons often fail to produce any behavioral effect. How does the brain compensate for such damage, and what are the limits of this compensation? We propose that neural circuits instantly compensate for neuron loss, thereby preserving their function as much as possible. We show that this compensation can explain changes in tuning curves induced by neuron silencing across a variety of systems, including the primary visual cortex. We find that compensatory mechanisms can be implemented through the dynamics of networks with a tight balance of excitation and inhibition, without requiring synaptic plasticity. The limits of this compensatory mechanism are reached when excitation and inhibition become unbalanced, thereby demarcating a recovery boundary, where signal representation fails and where diseases may become symptomatic. DOI: http://dx.doi.org/10.7554/eLife.12454.001 PMID:27935480

38 CFR 21.3023 - Nonduplication; pension, compensation, and dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Nonduplication; pension, compensation, and dependency and indemnity compensation. 21.3023 Section 21.3023 Pensions, Bonuses, and... Nonduplication; pension, compensation, and dependency and indemnity compensation. (a) Child; age 18. A child who...

Paraxial charge compensator for electron cryomicroscopy

International Nuclear Information System (INIS)

Berriman, John A.; Rosenthal, Peter B.

2012-01-01

We describe a multi-hole condenser aperture for the production of several electron beams in the transmission electron microscope (TEM) making it possible to simultaneously image and irradiate spatially separated regions of a specimen. When the specimen is a thin film of vitreous ice suspended over a holey carbon film, simultaneous irradiation of the adjacent carbon support with the off-axis beam compensates for some of the effects of charging in the image formed by a beam irradiating only the ice. Because the intervening region is not irradiated, charge-neutralization of frozen-hydrated specimens can occur by a through-space mechanism such as the emission of secondary electrons from a grounded carbon support film. We use paraxial charge compensation (PCC) to control the amount of charge build-up on the specimen and observe the effects of charge on images. The multi-hole aperture thus provides a tool for investigating the mechanism of charging and charge mitigation during the imaging of radiation sensitive biological specimens by cryomicroscopy. -- Highlights: ► A multi-hole condenser aperture produces multiple (paraxial) beams in TEM. ► Paraxial charge compensation is used to study electron-optical effects of charging. ► Emission of secondary electrons controls charging by a through space mechanism. ► Paraxial beams compensate for charging effects in frozen-hydrated specimens.

Paraxial charge compensator for electron cryomicroscopy

Energy Technology Data Exchange (ETDEWEB)

Berriman, John A. [Division of Physical Biochemistry, MRC National Institute for Medical Research, The Ridgeway, Mill Hill, London, NW7 1AA (United Kingdom); Rosenthal, Peter B., E-mail: peter.rosenthal@nimr.mrc.ac.uk [Division of Physical Biochemistry, MRC National Institute for Medical Research, The Ridgeway, Mill Hill, London, NW7 1AA (United Kingdom)

2012-05-15

We describe a multi-hole condenser aperture for the production of several electron beams in the transmission electron microscope (TEM) making it possible to simultaneously image and irradiate spatially separated regions of a specimen. When the specimen is a thin film of vitreous ice suspended over a holey carbon film, simultaneous irradiation of the adjacent carbon support with the off-axis beam compensates for some of the effects of charging in the image formed by a beam irradiating only the ice. Because the intervening region is not irradiated, charge-neutralization of frozen-hydrated specimens can occur by a through-space mechanism such as the emission of secondary electrons from a grounded carbon support film. We use paraxial charge compensation (PCC) to control the amount of charge build-up on the specimen and observe the effects of charge on images. The multi-hole aperture thus provides a tool for investigating the mechanism of charging and charge mitigation during the imaging of radiation sensitive biological specimens by cryomicroscopy. -- Highlights: Black-Right-Pointing-Pointer A multi-hole condenser aperture produces multiple (paraxial) beams in TEM. Black-Right-Pointing-Pointer Paraxial charge compensation is used to study electron-optical effects of charging. Black-Right-Pointing-Pointer Emission of secondary electrons controls charging by a through space mechanism. Black-Right-Pointing-Pointer Paraxial beams compensate for charging effects in frozen-hydrated specimens.

Administering the cost of death: organisational perspectives on workers' compensation and common law claims following traumatic death at work in Australia.

Science.gov (United States)

Quinlan, Michael; Fitzpatrick, Scott J; Matthews, Lynda R; Ngo, Mark; Bohle, Philip

2015-01-01

Quite apart from its devastating human and psychological effects, the death of a worker can have significant, life-changing effects on their families. For many affected families, workers' compensation entitlements represent the primary financial safeguard. Where the worker was self-employed, the family will generally be excluded from this remedy and have to take the more problematic option of claiming damages at common law. Despite the centrality of workers' compensation, little attention has been given to how effectively workers' compensation agencies address the needs of bereaved families or the views of other organisations involved, such as safety inspectors, unions, employers and victim advocates. Based on interviews with forty eight organisational representatives in five Australian states, this study examines how workers' compensation regimes deal with work-related death from the perspective of those organisations involved directly or indirectly in the process. The study highlighted a number of problems, including the exclusion of self-employed workers and dealing with 'mixed families'. Copyright © 2015 Elsevier Ltd. All rights reserved.

Tissue compensation using dynamic collimation on a linear accelerator

International Nuclear Information System (INIS)

Gaballa, Hani E.; Mitev, George; Zwicker, Robert D.; Ting, Joseph Y.; Tercilla, Oscar F.

1995-01-01

Purpose: The availability of computer-controlled collimators on some accelerators has led to techniques for dynamic beam modification, mainly to simulate beam wedge filters. This work addresses the practical aspects of dynamic tissue compensation in one dimension using available treatment-planning software. Methods and Materials: Data derived from the treatment-planning program is used with an iterative calculational routine to determine the monitor unit settings needed for the collimator-controlling computer. The method was first tested by simulating a 60 deg. physical wedge. Further studies were carried out on a specially fabricated plastic phantom that modeled the sagittal contour of the upper torso, neck, and lower head regions. Results: Dynamic wedge point doses generated by the planning program agreed within 1% with the values directly measured in a polystyrene phantom. In the patient phantom, dynamic collimation achieved calculated dose uniformity within 0.5% in a reference plane near the phantom midline. A comparison of computer-generated and measured point doses in this case showed agreement within 3%. Conclusions: Dynamic collimation can provide effective compensation for contours that vary primarily along one direction. A conventional treatment-planning program can be used to plan dynamic collimation and deliver a prescribed dose with reliable accuracy

Distributional effects of flood risk management - a cross-country comparison of preflood compensation

Directory of Open Access Journals (Sweden)

Willemijn J. van Doorn-Hoekveld

2016-12-01

Full Text Available We seek to examine the manner in which either the EU member states of France, the Netherlands, Poland, and Sweden or parts of them, such as the country of England in the UK or the Flemish Region in Belgium, deal with the distributional effects of the flood risk management strategies prevention, defense, and mitigation. Measures carried out in each of these strategies can cause preflood harm, as in the devaluation of property or loss of income. However, different member states and authorities address this harm in different ways. A descriptive overview of the different compensation regimes in the field of flood risk management is followed by an analysis of these differences and an explanation of what may cause them, such as the geographical differences that lead to differences in the way that they interfere with private rights and the dominant legal principles that underlie compensation regimes. An elaborated compensation regime could lead to more equitable and legitimate flood risk management because the burdens are fairly spread and all interests - including those of injured parties - are considered in the decision-making process. Our aim is to stimulate the hardly existent discussion on the financial harm that is caused by measures to prevent floods (preflood, in addition to the already existing discussion on the ex post flood distributional effects.

75 FR 76079 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-12-07

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

75 FR 53023 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-08-30

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

75 FR 22679 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-04-29

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

Digital, electromagnetic rod position indicator with compensation

International Nuclear Information System (INIS)

Feilchenfeld, M.M.; Geis, C.G.

1985-01-01

A digital rod position indicator having discrete coils L 0 , L 1 , L 2 ..... spaced along the travel path of an elongate magnetically permeable member stores in digital form compensation signals for automatically adjusting the location relative to the coils at which a digital output signal representative of the position of the end of the elongate member transitions from one code to the next. The appropriate compensation signal is addressed using the digital output signal and a correction factor which takes into account the direction of movement including reversals. Reference is made to the positioning of the control rods in a pressurized water reactor. (author)

Complexities in understanding the role of compensation-related factors on recovery from whiplash-associated disorders: discussion paper 2.

Science.gov (United States)

Carroll, Linda J; Connelly, Luke B; Spearing, Natalie M; Côté, Pierre; Buitenhuis, Jan; Kenardy, Justin

2011-12-01

Focused discussion. To present some of the complexities in conducting research on the role of compensation and compensation-related factors in recovery from whiplash-associated disorders (WAD) and to suggest directions for future research. There is divergence of opinion, primary research findings, and systematic reviews on the role of compensation and/or compensation-related factors in WAD recovery. The topic of research of compensation/compensation-related factors was discussed at an international summit meeting of 21 researchers from diverse fields of scientific enquiry. This article summarizes the main points raised in that discussion. Traffic injury compensation is a complex sociopolitical construct, which varies widely across jurisdictions. This leads to conceptual and methodological challenges in conducting and interpreting research in this area. It is important that researchers and their audiences be clear about what aspect of the compensation system is being addressed, what compensation-related variables are being studied, and what social/economic environment the compensation system exists in. In addition, summit participants also recommended that nontraditional, sophisticated study designs and analysis strategies be employed to clarify the complex causal pathways and mechanisms of effects. Care must be taken by both researchers and their audiences not to overgeneralize or confuse different aspects of WAD compensation. In considering the role of compensation/compensation-related factors on WAD and WAD recovery, it is important to retain a broad-based conceptualization of the range of biological, psychological, social, and economic factors that combine and interact to define and determine how people recover from WAD.

Integrated hybrid vibration isolator with feedforward compensation for fast high-precision positioning X/Y tables

International Nuclear Information System (INIS)

Yan, T H; Li, Q; Xu, C; Pu, H Y; Chen, X D

2010-01-01

The design, realization and control technologies of a high-performance hybrid microvibration isolator for ultra-high-precision high-speed moving X/Y tables are presented in this paper—the novel isolator with integrated passive–active high level of damping. The passive damping was implemented using air-springs in both vertical and horizontal directions, with parallel linear motors in two directions to realize the active damping and the positioning functions. It is an actual hybrid isolation system because its air-spring can also be controlled through the pneumatic loop. The isolation servo system also has fast positioning capability via the feedforward compensation for the moving tables. Compared with the conventional filtered reference type control algorithms that rely on the assumption for the adaptive filter and the controlled system, in which the disturbance is estimated from the residual signal, the feedforward compensation here shows high effectiveness of vibration isolation and high-precision positioning performance for its platform. The performance of feedforward compensation has been enhanced via an efficient state estimation adaptive algorithm, the fast Kalman filter. Finally, experimental demonstration has been shown for the prototype system and the results have verified the effectiveness of the proposed isolator system design and the adaptive control algorithm for substantially enhanced damping of the platform system with the moving X/Y tables

Implementation of a symmetric surface-electrode ion trap with field compensation using a modulated Raman effect

International Nuclear Information System (INIS)

Allcock, D T C; Sherman, J A; Stacey, D N; Burrell, A H; Curtis, M J; Imreh, G; Linke, N M; Szwer, D J; Webster, S C; Steane, A M; Lucas, D M

2010-01-01

We describe a new electrode design for a surface-electrode Paul trap, which allows rotation of the normal modes out of the trap plane, and a technique for micromotion compensation in all directions using a two-photon process, which avoids the need for an ultraviolet laser directed to the trap plane. The fabrication and characterization of the trap are described, as well as its implementation for the trapping and cooling of single Ca + ions. We also propose a repumping scheme that increases ion fluorescence and simplifies heating rate measurements obtained by time-resolved ion fluorescence during Doppler cooling.

Implementation of a symmetric surface-electrode ion trap with field compensation using a modulated Raman effect

Science.gov (United States)

Allcock, D. T. C.; Sherman, J. A.; Stacey, D. N.; Burrell, A. H.; Curtis, M. J.; Imreh, G.; Linke, N. M.; Szwer, D. J.; Webster, S. C.; Steane, A. M.; Lucas, D. M.

2010-05-01

We describe a new electrode design for a surface-electrode Paul trap, which allows rotation of the normal modes out of the trap plane, and a technique for micromotion compensation in all directions using a two-photon process, which avoids the need for an ultraviolet laser directed to the trap plane. The fabrication and characterization of the trap are described, as well as its implementation for the trapping and cooling of single Ca+ ions. We also propose a repumping scheme that increases ion fluorescence and simplifies heating rate measurements obtained by time-resolved ion fluorescence during Doppler cooling.

Influence of gravity compensation on kinematics and muscle activation patterns during reach and retrieval in subjects with cervical spinal cord injury: An explorative study

OpenAIRE

Marieke G . M. Kloosterman, PT, MSc; Govert J. Snoek, MD, PhD; Mirjam Kouwenhoven, MD; Anand V. Nene, MD, PhD; Michiel J. A. Jannink, PhD

2010-01-01

Many interventions in upper-limb rehabilitation after cervical spinal cord injury (CSCI) use arm support (gravity compensation); however, its specific effects on kinematics and muscle activation characteristics in subjects with a CSCI are largely unknown. We conducted a cross-sectional explorative study to study these effects. Nine subjects with a CSCI performed two goal-directed arm movements (maximal reach, reach and retrieval) with and without gravity compensation. Angles at elbow and shou...

OLT-centralized sampling frequency offset compensation scheme for OFDM-PON.

Science.gov (United States)

Chen, Ming; Zhou, Hui; Zheng, Zhiwei; Deng, Rui; Chen, Qinghui; Peng, Miao; Liu, Cuiwei; He, Jing; Chen, Lin; Tang, Xionggui

2017-08-07

We propose an optical line terminal (OLT)-centralized sampling frequency offset (SFO) compensation scheme for adaptively-modulated OFDM-PON systems. By using the proposed SFO scheme, the phase rotation and inter-symbol interference (ISI) caused by SFOs between OLT and multiple optical network units (ONUs) can be centrally compensated in the OLT, which reduces the complexity of ONUs. Firstly, the optimal fast Fourier transform (FFT) size is identified in the intensity-modulated and direct-detection (IMDD) OFDM system in the presence of SFO. Then, the proposed SFO compensation scheme including phase rotation modulation (PRM) and length-adaptive OFDM frame has been experimentally demonstrated in the downlink transmission of an adaptively modulated optical OFDM with the optimal FFT size. The experimental results show that up to ± 300 ppm SFO can be successfully compensated without introducing any receiver performance penalties.

Comparison of the effect of BCAA granules on between decompensated and compensated cirrhosis.

Science.gov (United States)

Habu, Daiki; Nishiguchi, Shuhei; Nakatani, Shinji; Lee, Chulyoo; Enomoto, Masaru; Tamori, Akihiro; Takeda, Tadashi; Ohfuji, Satoko; Fukushima, Wakaba; Tanaka, Takashi; Kawamura, Etsuji; Shiomi, Susumu

2009-01-01

We designed a randomized trial to examine whether increase or preservation of serum albumin levels was attained with administration of branched-chain amino acid (BCAA) granules for compensated cirrhosis, compared with decompensated cirrhosis. Sixty-five patients with HCV-related cirrhosis with serum albumin level less than 4.0 g/dl were enrolled in this study. Half of the patients were randomly assigned to receive 14.22 g/day of BCAA granules orally, and half were assigned to a control group. Patients were evaluated at entry and at 1-year intervals for at least 2 years. The parameters were divided into 3 categories. Class 1 was decompensated cirrhosis with serum albumin level less than 3.5 mg/dl. Class 2 was compensated cirrhosis with serum albumin level over 3.6 mg/dl and molar ratio of BCAA to tyrosine (BTR) less than 4. Class 3 was compensated cirrhosis with serum albumin level over 3.6 mg/dl and BTR over 4. In class 1 and class 2, the BCAA group exhibited significantly higher rates of maintaining serum albumin level than the control group for 2 years. In contrast, there was no significant difference between the BCAA group and control group in rate of maintaining serum albumin levels in class 3. Those results suggested that if cirrhotic patients were in the compensated stage at the entry but with lower BTR, as for decompensated cirrhosis, oral BCAA supplementation might be effective in maintaining serum albumin level for 2 years.

Local governments' roles of the compensation for damage by the Tokai JCO criticality accident

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Tomoyuki [Central Research Inst. of Electric Power Industry, Tokyo (Japan). Socio-Economic Research Center

2003-03-01

The Tokai JCO criticality accident on September 30, 1999 was the first case to which The Law on Compensation for Nuclear Damage was applied. Although the Law on Compensation for Nuclear Damage formulates the outline of the institutional framework for nuclear third party liability together with operator's insurance scheme, details of actual compensation procedure are not specified. By this reason, the compensation procedure in the Tokai accident had been executed without a concrete legal specification and a precedent. In spite of this situation, the compensation procedure with the accident led to an unexpectedly successful result. We observe the several reasons why the compensation procedure was implemented successfully despite the lack of concrete legal specification and a precedent. One of the reasons is that the local governments, Tokai Village and Ibaraki Prefecture, immediately took the leadership in implementing a temporary regime of compensation procedure without wasting time for waiting national government's directives. Upon practicing this compensation procedure, the local governments implemented the following steps. (1) Initial estimation of the amount and scope of damage. (2) Providing the criteria and heads of damage subject to compensation. (3) Unitary compensation procedure at the local levels. (4) Distribution of emergency payments for the victims. (5) Facilitating compensatory negotiation between the victims and JCO as arbitrator. However, some concerns are also pointed out about the fact that the local government directed the whole procedure without sufficient adjustment with the national government for compensation policy. Among all, in the compensation led by the local governments, it was difficult to guarantee fairness of compensation because victims who are influential on the local government such as industrial associations would have unfairly strong negotiation power in the compensatory negotiation, while the operator being

The art of directing a workers' compensation claim: personal observations on the role of the workers' compensation claim adjuster.

Science.gov (United States)

Wendt, Chris; Emmett, Ted

2004-05-01

Workers' compensation claims are becoming more complex and expensive every day. One of the contributing factors for the increase is the aging workforce as well as federal legislation such as the Americans with Disabilities Act (ADA) and the Family and Medical Leave Act (FMLA). The workforce is aging, mobile, and educated about their rights. The key to avoiding spiraling costs is a strong safety and claims program that is sponsored by senior management,valued by the employees, and implemented by the entire company.

Re-Planning for Compensator-Based IMRT with Original Compensators

International Nuclear Information System (INIS)

Zhang, Geoffrey; Feygelman, Vladimir; Stevens, Craig; Li Weiqi; Leuthold, Susan; Springett, Gregory; Hoffe, Sarah

2011-01-01

Compared with multileaf collimator (MLC)-based intensity-modulated radiotherapy (IMRT) for moving targets, compensator-based IMRT has advantages such as shorter beam-on time, fewer monitor units with potentially decreased secondary carcinogenesis risk, better optimization-to-deliverable dose conversion, and often better dose conformity. Some of the disadvantages include additional time for the compensators to be built and delivered, as well as extra cost. Patients undergoing treatment of abdominal cancers often experience weight loss. It would be necessary to account for this change in weight with a new plan and a second set of compensators. However, this would result in treatment delays and added costs. We have developed a method to re-plan the patient using the same set of compensators. Because the weight changes seen with the treatment of abdominal cancers are usually relatively small, a new 4D computed tomography (CT) acquired in the treatment position with markers on the original isocenter tattoos can be registered to the original planning scan. The contours of target volumes from the original scans are copied to the new scan after fusion. The original compensator set can be used together with a few field-in-field (FiF) beams defined by the MLC (or beams with cerrobend blocks for accelerators not equipped with a MLC). The weights of the beams with compensators are reduced so that the FiF or blocked beams can be optimized to mirror the original plan and dose distribution. Seven abdominal cancer cases are presented using this technique. The new plan on the new planning CT images usually has the same dosimetric quality as the original. The target coverage and dose uniformity are improved compared with the plan without FiF/block modification. Techniques combining additional FiF or blocked beams with the original compensators optimize the treatment plans when patients lose weight and save time and cost compared with generating plans with a new set of compensators.

US-LHC IR magnet error analysis and compensation

International Nuclear Information System (INIS)

Wei, J.; Ptitsin, V.; Pilat, F.; Tepikian, S.; Gelfand, N.; Wan, W.; Holt, J.

1998-01-01

This paper studies the impact of the insertion-region (IR) magnet field errors on LHC collision performance. Compensation schemes including magnet orientation optimization, body-end compensation, tuning shims, and local nonlinear correction are shown to be highly effective

Is there a clinical benefit with a smooth compensator design compared with a plunged compensator design for passive scattered protons?

Energy Technology Data Exchange (ETDEWEB)

Tabibian, Art A., E-mail: art.tabibian@gmail.com [University of Texas School of Allied Health-Medical Dosimetry, Houston, TX (United States); Powers, Adam; Dolormente, Keith; Oommen, Sneha; Tiwari, Akhil [University of Texas School of Allied Health-Medical Dosimetry, Houston, TX (United States); Palmer, Matt [MD Anderson Department of Radiation Oncology, Houston, TX (United States); Zhu, Xiaorong R.; Li, Heng; Sahoo, Narayan; Wisdom, Paul [MD Anderson Department of Radiation Physics, Houston, TX (United States); Velasco, Kyle [Radiation Oncology Resources, Goshen, IN (United States); Erhart, Kevin; Stanley, Henry [Decimal, Inc, Sanford, FL (United States); Nguyen, Bao-Ngoc T. [MD Anderson Department of Radiation Oncology, Houston, TX (United States)

2015-04-01

In proton therapy, passive scattered proton plans use compensators to conform the dose to the distal surface of the planning volume. These devices are custom made from acrylic or wax for each treatment field using either a plunge-drilled or smooth-milled compensator design. The purpose of this study was to investigate if there is a clinical benefit of generating passive scattered proton radiation treatment plans with the smooth compensator design. We generated 4 plans with different techniques using the smooth compensators. We chose 5 sites and 5 patients for each site for the range of dosimetric effects to show adequate sample. The plans were compared and evaluated using multicriteria (MCA) plan quality metrics for plan assessment and comparison using the Quality Reports [EMR] technology by Canis Lupus LLC. The average absolute difference for dosimetric metrics from the plunged-depth plan ranged from −4.7 to +3.0 and the average absolute performance results ranged from −6.6% to +3%. The manually edited smooth compensator plan yielded the best dosimetric metric, +3.0, and performance, + 3.0% compared to the plunged-depth plan. It was also superior to the other smooth compensator plans. Our results indicate that there are multiple approaches to achieve plans with smooth compensators similar to the plunged-depth plans. The smooth compensators with manual compensator edits yielded equal or better target coverage and normal tissue (NT) doses compared with the other smooth compensator techniques. Further studies are under investigation to evaluate the robustness of the smooth compensator design.

Analysis and Compensation of Dead-Time Effect of a ZVT PWM Inverter Considering the Rise- and Fall-Times

Directory of Open Access Journals (Sweden)

Hailin Zhang

2016-11-01

Full Text Available The dead-time effect, as an intrinsic problem of the converters based on the half-bridge unit, leads to distortions in the converter output. Although several dead-time effect compensation or elimination methods have been proposed, they cannot fully remove the dead-time effect of blanking delay error, because the output current polarity is difficult detect accurately. This paper utilizes the zero-voltage-switching (ZVT technique to eliminate the blanking delay error, which is the main drawback of the hard-switching inverter, although the technique initially aims to improve the efficiency. A typical ZVT inverter—the auxiliary resonant snubber inverter (ARSI is analyzed. The blanking delay error is completely eliminated in the ARSI. Another error source caused by the finite rise- and fall-times of the voltage is analyzed, which was not considered in the hard-switching inverter. A compensation method based on the voltage error estimation is proposed to compensate the rise- and fall-error. A prototype was developed to verify the effectiveness of the proposed control. Both the simulation and experimental results demonstrate that the qualities of the output current and voltage in the ARSI are better than that in the hard-switching inverter due to the elimination of the blanking delay error. The total harmonic distortion (THD of the output is further reduced by using the proposed compensation method in the ARSI.

Compensations to Local Communities in the Krsko NPP Decommissioning Program

International Nuclear Information System (INIS)

Levanat, I.; Knapp, A.; Lokner, V.

2010-01-01

In Slovenia, direct financial compensations (for 'limited land use') to local communities hosting nuclear facilities were initially specified by a government Decree from 2003. In Croatia, a possibility of direct financial compensations had been indicated in the land use plan in conjunction with the prospective RW repository siting about a decade earlier, but the topic was subsequently abandoned together with the repository project. In 2004, the joint Slovenian-Croatian Decommissioning and LILW and SF management program for NPP Krsko from 2004 (the 1st revision of the joint Program) conservatively included the compensation amounts from the Slovenian Decree into the cost estimates of LILW and SF repositories, although their location was entirely unspecified ('in Slovenia or in Croatia'). Shortly before the 2nd revision of the joint Program started in the fall of 2008, the Slovenian government had amended its Decree, practically doubling the amounts of the repository compensations. Assuming that some (or possibly all) nuclear facilities and waste, dealt with in the Program, may be located in Slovenia, the revision has adopted a conservative approach to include all compensations to local communities that may be required by the Slovenian regulations into the Program costs. This paper discusses the Slovenian government Decree, its impact on the joint Program costs, and its implications on RW and SF management in the region. The Decree suffers from the lack of self-consistency, clarity, and consistency with the more general legal provisions on which it should have been based, but it may have an important supporting role in the process of RW and SF management facilities siting. The Decree introduced significant additional costs into the joint Program, which have grown from about one hundred million eur in the 1st revision to about half a billion in this revision (depending on the Program scenario). Besides, application of the Decree in the joint Program has set a precedent

The unconstitutionality of the environmental compensation: an analyse of the ADIn (Direct Action of Unconstitutionality) 3378; A inconstitucionalidade da compensacao ambiental: uma analise da ADIn (Acao Direta de Inconstitucionalidade) 3378

Energy Technology Data Exchange (ETDEWEB)

Reis, Marcio Monteiro; Masseli, Sandro [Siqueira Castro Advogados, Sao Paulo, SP (Brazil). Setor Regulatorio e Ambiental

2008-07-01

The following paper aims to analyze the judgment of a specific Direct Action of Unconstitutionality ('ADI') filed by the Brazilian National Industry Confederation regarding the constitutionality of environmental compensation fee as disposed by Law 9.985. Such ADI was also sponsored by the Brazilian Oil, Gas and Biofuels Institute ('IBP') as 'amicus curiae'. In light of this, an environmental compensation timeline will be presented in order to support its charging evolution. By doing this we will be in a position to balance economic development and environment. (author)

Flywheels Would Compensate for Rotor Imbalance

Science.gov (United States)

Hrastar, J. A. S.

1982-01-01

Spinning flywheels within rotor can null imbalance forces in rotor. Flywheels axes are perpendicular to each other and to rotor axis. Feedback signals from accelerometers or strain gages in platform control flywheel speeds and rotation directions. Concept should be useful for compensating rotating bodies on Earth. For example, may be applied to large industrial centrifuge, particularly if balance changes during operation.

[Study on the Effects and Compensation Effect of Recording Parameters Error on Imaging Performance of Holographic Grating in On-Line Spectral Diagnose].

Science.gov (United States)

Jiang, Yan-xiu; Bayanheshig; Yang, Shuo; Zhao, Xu-long; Wu, Na; Li, Wen-hao

2016-03-01

To making the high resolution grating, a numerical calculation was used to analyze the effect of recording parameters on groove density, focal curve and imaging performance of the grating and their compensation. Based on Fermat' s principle, light path function and aberration, the effect on imaging performance of the grating was analyzed. In the case of fixed using parameters, the error of the recording angle has a greater influence on imaging performance, therefore the gain of the weight of recording angle can improve the accuracy of the recording angle values in the optimization; recording distance has little influence on imaging performance; the relative errors of recording parameters cause the change of imaging performance of the grating; the results indicate that recording parameter errors can be compensated by adjusting its corresponding parameter. The study can give theoretical guidance to the fabrication for high resolution varied-line-space plane holographic grating in on-line spectral diagnostic and reduce the alignment difficulty by analyze the main error effect the imaging performance and propose the compensation method.

Automatic Detection of Compensation During Robotic Stroke Rehabilitation Therapy.

Science.gov (United States)

Zhi, Ying Xuan; Lukasik, Michelle; Li, Michael H; Dolatabadi, Elham; Wang, Rosalie H; Taati, Babak

2018-01-01

Robotic stroke rehabilitation therapy can greatly increase the efficiency of therapy delivery. However, when left unsupervised, users often compensate for limitations in affected muscles and joints by recruiting unaffected muscles and joints, leading to undesirable rehabilitation outcomes. This paper aims to develop a computer vision system that augments robotic stroke rehabilitation therapy by automatically detecting such compensatory motions. Nine stroke survivors and ten healthy adults participated in this study. All participants completed scripted motions using a table-top rehabilitation robot. The healthy participants also simulated three types of compensatory motions. The 3-D trajectories of upper body joint positions tracked over time were used for multiclass classification of postures. A support vector machine (SVM) classifier detected lean-forward compensation from healthy participants with excellent accuracy (AUC = 0.98, F1 = 0.82), followed by trunk-rotation compensation (AUC = 0.77, F1 = 0.57). Shoulder-elevation compensation was not well detected (AUC = 0.66, F1 = 0.07). A recurrent neural network (RNN) classifier, which encodes the temporal dependency of video frames, obtained similar results. In contrast, F1-scores in stroke survivors were low for all three compensations while using RNN: lean-forward compensation (AUC = 0.77, F1 = 0.17), trunk-rotation compensation (AUC = 0.81, F1 = 0.27), and shoulder-elevation compensation (AUC = 0.27, F1 = 0.07). The result was similar while using SVM. To improve detection accuracy for stroke survivors, future work should focus on predefining the range of motion, direct camera placement, delivering exercise intensity tantamount to that of real stroke therapies, adjusting seat height, and recording full therapy sessions.

Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

Energy Technology Data Exchange (ETDEWEB)

Le Coroller, Y. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-09-01

A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux

Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

Energy Technology Data Exchange (ETDEWEB)

Le Coroller, Y [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-09-01

A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux millimetres fonctionnent

Study on Compensation Control of STATCOM Based on MMC

Directory of Open Access Journals (Sweden)

Xie Yan

2016-01-01

Full Text Available This paper introduced modular multi-level converter (MMC, which could enhance the voltage and power level by sub-converter modules in series and was easy to extend to any level of output. Its structure and working mechanism were described. By analyzing the energy transfer performance of STATCOM based on MMC working conditions in the compensation, a comprehensive compensation control strategy was proposed based on direct current control mode. By analyzing the higher harmonic components circulation generated by the inconsistencies in the three-phase upper and lower arm voltage, a loop control strategy is proposed for the suppression of the circulation in the arms of the M-STATCOM. The simulation results show the strategy has a better tracking precision and response speed for the compensation control.

Lock-in thermography measurements of the spin Peltier effect in a compensated ferrimagnet and its comparison to the spin Seebeck effect

Science.gov (United States)

Yagmur, A.; Iguchi, R.; Geprägs, S.; Erb, A.; Daimon, S.; Saitoh, E.; Gross, R.; Uchida, K.

2018-05-01

The spin Peltier effect (SPE) in a junction comprising a gadolinium-iron-garnet (GdIG) slab and a Pt film has been investigated around the magnetization compensation temperature of GdIG by means of the lock-in thermography method. When a charge current is applied to the Pt layer, a spin current is generated across the Pt/GdIG interface via the spin Hall effect in Pt. This spin current induces a heat current and a measurable temperature change near the Pt/GdIG interface due to the SPE. The SPE signal in the Pt/GdIG junction shows a sign change around the magnetization compensation temperature, demonstrating the similar temperature dependence of the SPE and the spin Seebeck effect for the Pt/GdIG hybrid system.

Reactive power compensating system

Energy Technology Data Exchange (ETDEWEB)

Williams, Timothy J. (Redondo Beach, CA); El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Seattle, WA)

1987-01-01

The reactive power of an induction machine is compensated by providing fixed capacitors on each phase line for the minimum compensation required, sensing the current on one line at the time its voltage crosses zero to determine the actual compensation required for each phase, and selecting switched capacitors on each line to provide the balance of the compensation required.

Compensation techniques for non-linearities in H-bridge inverters

Directory of Open Access Journals (Sweden)

Daniel Zammit

2016-12-01

Full Text Available This paper presents compensation techniques for component non-linearities in H-bridge inverters as those used in grid-connected photovoltaic (PV inverters. Novel compensation techniques depending on the switching device current were formulated to compensate for the non-linearities in inverter circuits caused by the voltage drops on the switching devices. Both simulation and experimental results will be presented. Testing was carried out on a PV inverter which was designed and constructed for this research. Very satisfactory results were obtained from all the compensation techniques presented, however the exact compensation method was the most effective, providing the highest reduction in harmonics.

Improvement of the matrix effect compensation in active neutron measurement by simulated annealing algorithm (June 2009)

International Nuclear Information System (INIS)

Raoux, A. C.; Loridon, J.; Mariani, A.; Passard, C.

2009-01-01

Active neutron measurements such as the Differential Die-Away (DDA) technique involving pulsed neutron generator, are widely applied to determine the fissile content of waste packages. Unfortunately, the main drawback of such techniques is coming from the lack of knowledge of the waste matrix composition. Thus, the matrix effect correction for the DDA measurement is an essential improvement in the field of fissile material content determination. Different solutions have been developed to compensate the effect of the matrix on the neutron measurement interpretation. In this context, this paper describes an innovative matrix correction method we have developed with the goal of increasing the accuracy of the matrix effect correction and reducing the measurement time. The implementation of this method is based on the analysis of the raw signal with an optimisation algorithm called the simulated annealing algorithm. This algorithm needs a reference data base of Multi-Channel Scaling (MCS) spectra, to fit the raw signal. The construction of the MCS library involves a learning phase to define and acquire the DDA signals. This database has been provided by a set of active signals from experimental matrices (mock-up waste drums of 118 litres) recorded in a specific device dedicated to neutron measurement research and development of the Nuclear Measurement Laboratory of CEA-Cadarache, called PROMETHEE 6. The simulated annealing algorithm is applied to make use of the effect of the matrices on the total active signal of DDA measurement. Furthermore, as this algorithm is directly applied to the raw active signal, it is very useful when active background contributions can not be easily estimated and removed. Most of the cases tested during this work which represents the feasibility phase of the method, are within a 4% agreement interval with the expected experimental value. Moreover, one can notice that without any compensation of the matrix effect, the classical DDA prompt

Improvement of the matrix effect compensation in active neutron measurement by simulated annealing algorithm (June 2009)

Energy Technology Data Exchange (ETDEWEB)

Raoux, A. C.; Loridon, J.; Mariani, A.; Passard, C. [French Atomic Energy Commission, DEN, Cadarache, F-3108 Saint-Paul-Lez-Durance (France)

2009-07-01

Active neutron measurements such as the Differential Die-Away (DDA) technique involving pulsed neutron generator, are widely applied to determine the fissile content of waste packages. Unfortunately, the main drawback of such techniques is coming from the lack of knowledge of the waste matrix composition. Thus, the matrix effect correction for the DDA measurement is an essential improvement in the field of fissile material content determination. Different solutions have been developed to compensate the effect of the matrix on the neutron measurement interpretation. In this context, this paper describes an innovative matrix correction method we have developed with the goal of increasing the accuracy of the matrix effect correction and reducing the measurement time. The implementation of this method is based on the analysis of the raw signal with an optimisation algorithm called the simulated annealing algorithm. This algorithm needs a reference data base of Multi-Channel Scaling (MCS) spectra, to fit the raw signal. The construction of the MCS library involves a learning phase to define and acquire the DDA signals. This database has been provided by a set of active signals from experimental matrices (mock-up waste drums of 118 litres) recorded in a specific device dedicated to neutron measurement research and development of the Nuclear Measurement Laboratory of CEA-Cadarache, called PROMETHEE 6. The simulated annealing algorithm is applied to make use of the effect of the matrices on the total active signal of DDA measurement. Furthermore, as this algorithm is directly applied to the raw active signal, it is very useful when active background contributions can not be easily estimated and removed. Most of the cases tested during this work which represents the feasibility phase of the method, are within a 4% agreement interval with the expected experimental value. Moreover, one can notice that without any compensation of the matrix effect, the classical DDA prompt

Robotic Assistance by Impedance Compensation for Hand Movements While Manual Welding.

Science.gov (United States)

Erden, Mustafa Suphi; Billard, Aude

2016-11-01

In this paper, we present a robotic assistance scheme which allows for impedance compensation with stiffness, damping, and mass parameters for hand manipulation tasks and we apply it to manual welding. The impedance compensation does not assume a preprogrammed hand trajectory. Rather, the intention of the human for the hand movement is estimated in real time using a smooth Kalman filter. The movement is restricted by compensatory virtual impedance in the directions perpendicular to the estimated direction of movement. With airbrush painting experiments, we test three sets of values for the impedance parameters as inspired from impedance measurements with manual welding. We apply the best of the tested sets for assistance in manual welding and perform welding experiments with professional and novice welders. We contrast three conditions: 1) welding with the robot's assistance; 2) with the robot when the robot is passive; and 3) welding without the robot. We demonstrate the effectiveness of the assistance through quantitative measures of both task performance and perceived user's satisfaction. The performance of both the novice and professional welders improves significantly with robotic assistance compared to welding with a passive robot. The assessment of user satisfaction shows that all novice and most professional welders appreciate the robotic assistance as it suppresses the tremors in the directions perpendicular to the movement for welding.

Criteria for emittance compensation in high-brightness photoinjectors

Directory of Open Access Journals (Sweden)

Chun-xi Wang

2007-10-01

Full Text Available A critical process in high-brightness photoinjectors is emittance compensation, which brings under control the correlated transverse emittance growth due to the linear space-charge force. Although emittance compensation has been used and studied for almost two decades, the exact criteria to achieve emittance compensation is not as clear as it should be. In this paper, a perturbative analysis of slice envelopes and emittance evolution close to any reference envelope is developed, via which space-charge and chromatic effects are investigated. A new criterion for emittance compensation is found, which is complementary to the well-known matching condition for the invariant envelope and agrees very well with simulations.

Research on the Mechanism of Cross Regional Grassland Ecological Compensation

Science.gov (United States)

Yang, Ran; Ma, Jun

2018-01-01

In recent years, grassland environmental damage has become serious, and grassland resources protection task has become heavy, grassland ecological compensation has become an effective way to solve this problem; but the current grassland ecological compensation standards were low, the effect is poor. The fundamental reason is the model of administrative division destroys the integrity of grassland. Based on the analysis of the status quo of grassland compensation, this paper tries to protect the grassland integrity, breaks the administrative division restriction, implements the space regulation, constructs the framework of cross-regional grassland ecological compensation mechanism, describes its operation process. It provides new way to realize the sustainable development of the grassland environment.

Accommodating practical constraints for intensity modulated radiation therapy by means of compensators

International Nuclear Information System (INIS)

Meyer, Juergen

2002-01-01

The thesis deals with the practical implementation of intensity modulated radiation therapy (IMRT) generated by means of patient specific metal compensators. An elaborate comparison between several compensator-machining techniques, with respect to their suitability for production within a hospital workshop, is presented. The limitations associated with the selected compensator manufacturing technique are identified and implemented as constraints in an existing inverse treatment-planning algorithm. In order to obtain the profile of a compensator, which produces a desired intensity distribution, inverse modeling of the radiation attenuation within the compensator is required. Two novel and independent approaches, based on deconvolution and system identification, are proposed to accomplish this. To compare the approach with the 'rival' state of the art beam modulation technique, a theoretical and experimental examination of the modulated fields generated by manufactured compensators and multileaf collimators is presented. This comparison focused on the achievable resolution of the intensity modulated beams in lateral and longitudinal directions. To take into account the characteristics of a clinical environment the suitability of the most common commercially available treatment couch systems for IMRT treatments is studied. An original rule based advisory system is developed to alert the operator of any potential collision of the beam with the movable supporting structures of the treatment couch. The system is capable of finding alternative positions for the supporting frames and, if necessary, can suggest alternative beam directions. Finally, a head and neck phantom is designed for gel dosimetry to assess IMRT treatment delivery techniques. The phantom is based on a simplistic but realistic design and contains the main anatomical features

A Novel Time-Varying Friction Compensation Method for Servomechanism

Directory of Open Access Journals (Sweden)

Bin Feng

2015-01-01

Full Text Available Friction is an inevitable nonlinear phenomenon existing in servomechanisms. Friction errors often affect their motion and contour accuracies during the reverse motion. To reduce friction errors, a novel time-varying friction compensation method is proposed to solve the problem that the traditional friction compensation methods hardly deal with. This problem leads to an unsatisfactory friction compensation performance and the motion and contour accuracies cannot be maintained effectively. In this method, a trapezoidal compensation pulse is adopted to compensate for the friction errors. A generalized regression neural network algorithm is used to generate the optimal pulse amplitude function. The optimal pulse duration function and the pulse amplitude function can be established by the pulse characteristic parameter learning and then the optimal friction compensation pulse can be generated. The feasibility of friction compensation method was verified on a high-precision X-Y worktable. The experimental results indicated that the motion and contour accuracies were improved greatly with reduction of the friction errors, in different working conditions. Moreover, the overall friction compensation performance indicators were decreased by more than 54% and this friction compensation method can be implemented easily on most of servomechanisms in industry.

Dynamic Compensation for Two-Axis Robot Wrist Force Sensors

Directory of Open Access Journals (Sweden)

Junqing Ma

2013-01-01

Full Text Available To improve the dynamic characteristic of two-axis force sensors, a dynamic compensation method is proposed. The two-axis force sensor system is assumed to be a first-order system. The operation frequency of the system is expanded by a digital filter with backward difference network. To filter high-frequency noises, a low-pass filter is added after the dynamic compensation network. To avoid overcompensation, parameters of the proposed dynamic compensation method are defined by trial and error. Step response methods are utilized in dynamic calibration experiments. Compared to experiment data without compensation, the response time of the dynamic compensated data is reduced by 30%~40%. Experiments results demonstrate the effectiveness of our method.

Space Charge Compensation in the Linac4 Low Energy Beam Transport Line with Negative Hydrogen Ions

CERN Document Server

Valerio-Lizarraga, C; Leon-Monzon, I; Lettry, J; Midttun, O; Scrivens, R

2014-01-01

The space charge effect of low energy, unbunched ion beams can be compensated by the trapping of ions or electrons into the beam potential. This has been studied for the 45 keV negative hydrogen ion beam in the CERN Linac4 Low Energy Beam Tranport (LEBT) using the package IBSimu1, which allows the space charge calculation of the particle trajectories. The results of the beam simulations will be compared to emittance measurements of an H- beam at the CERN Linac4 3 MeV test stand, where the injection of hydrogen gas directly into the beam transport region has been used to modify the space charge compensation degree.

Simulation and Analysis of Passive Rolling Compensation of High Sea Salvage System

Directory of Open Access Journals (Sweden)

Lin Liqun

2017-01-01

Full Text Available Method and device of a flexible interception and salvage system was introduced in this paper. In order to study the effect of wave motion on salvage operation, we proposed a passive wave compensation scheme that utilizes a combination of variable-pitch cylinders and accumulators, and established the mathematical vibration model of the rolling motion of the salvage compensation system. With the relationships between the stiffness coefficient and the accumulator parametric of passive compensated gas-liquid system, we determined the effective compensation stiffness range through Mathematica simulation analysis. The relationship between the roll displacement of the salvage arm and the initial volume Vo of the accumulator has been analysed. The results show that the accumulatorVo in a certain range has a great influence on the passive compensation. However, when the volume is greater than 20m3, the compensation effect is weakened, and tend to a certain value, irrespective of the passive system accumulator volume capacity, it does not achieve full compensation. The results have important guidance on the design and optimization of rolling passive compensation of the practical high sea salvage system.

Understanding the positive effect of financial compensation on trust after norm violations: Evidence from fMRI in favor of forgiveness.

Science.gov (United States)

Haesevoets, Tessa; De Cremer, David; Van Hiel, Alain; Van Overwalle, Frank

2018-05-01

Norm violations are ubiquitous in organizations and often result in tangible harm and a loss of trust. One possible response to enhance trust involves the provision of financial compensation. Unfortunately, little is known about the processes that underlie the effect of such a tangible response to increase trust. We employed techniques in cognitive neuroscience (functional magnetic resonance imaging) to examine these processes. Participants placed in the scanner played the role of recipient in a series of dictator games with different allocators who (unknown to them) were preprogrammed. An unequal division of resources was used as a norm violation that resulted in a financial loss. Afterward the inflicted harm was restored through equal financial compensation. Our neuroimaging data indicate that financial compensation activates forgiveness-related brain areas and that this activation mediates the positive effect of financial compensation on trust. We discuss the theoretical and managerial implications of using tangible responses to increase trust in organizational settings. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

How much should customers be compensated for interruptions in the drinking water supply?

Science.gov (United States)

Molinos-Senante, María; Sala-Garrido, Ramon

2017-05-15

Water supply interruptions directly affect customers, and customers should be compensated accordingly. However, few water regulators have applied compensation policies given the difficulty of estimating the economic value of compensation to customers. In this study, a pioneering approach based on the concept of shadow prices is proposed to determine the compensation that customers should receive for unplanned water interruptions. The Chilean water industry was selected as a case study because there is an ongoing policy discussion between the use of penalties or compensation as an incentive to prevent water supply interruptions. The estimated results indicate that for 2014, the value of compensation ranges between 2.4% and 35.4% of the fixed charge of the water tariff. The methodology and findings of this study are of great relevance to water regulators in defining incentives to prompt water companies to provide reliable water service. Copyright © 2017 Elsevier B.V. All rights reserved.

Teacher Compensation and Organization.

Science.gov (United States)

Kelley, Carolyn

1997-01-01

Examines changes in the conceptualization of schooling over time from an organizational perspective. Explores how compensation systems might be better designed to match alternative organizational designs, considering scientific management, effective schools, content-driven schooling, and high standards/high involvement schools as organizational…

Feasibility of compensating for EUV field edge effects through OPC

Science.gov (United States)

Maloney, Chris; Word, James; Fenger, Germain L.; Niroomand, Ardavan; Lorusso, Gian F.; Jonckheere, Rik; Hendrickx, Eric; Smith, Bruce W.

2014-04-01

implementation of these measurements allow for further mitigation, i.e., compensation by OPC. Mentor Graphics' Calibre software uses the scanner's point spread function and convolves it with the mask layout to generate a flare map. It also has the capability to add additional dose to the image border which can be optimized to fit the experimental data. This includes the transition region between the image field and border that results in a linear rolloff of dose due to partial shadowing of the REMA blades. By applying this flaremap that accounts for neighboring die to the already calibrated optical and resist models, OPC can now be enabled to compensate for field edge effects. This study has two goals. First, we will show that OPC can be used to compensate both for field edge effects with and without a etched ML border. The second is to investigate the limitations that exist for OPC in the areas altered by neighboring die. This will predict when a process to mitigate the field edge effect is needed to enable EUV HVM.

Depolarization artifacts in dual rotating-compensator Mueller matrix ellipsometry

International Nuclear Information System (INIS)

Li, Weiqi; Zhang, Chuanwei; Jiang, Hao; Chen, Xiuguo; Liu, Shiyuan

2016-01-01

Noticeable depolarization effects are observed in the measurement of the air using an in-house developed dual rotating-compensator Mueller matrix ellipsometer. We demonstrate that these depolarization effects are essentially artifacts and mainly induced when the compensator with wavelength-dependent optical properties is integrated with the finite bandwidth detector. We define a general formula to represent the actual Mueller matrix of the compensator by taking into account the depolarization artifacts. After incorporating this formula into the system model, a correction method is further proposed, and consequently, improved accuracy can be achieved in the Mueller matrix measurement. (paper)

Essays in Executive Compensation

NARCIS (Netherlands)

D. Zhang (Dan)

2012-01-01

textabstractThis dissertation focuses on how executive compensation is designed and its implications for corporate finance and government regulations. Chapter 2 analyzes several proposals to restrict CEO compensation and calibrates two models of executive compensation that describe how firms would

Exploring the importance of different items as reasons for leaving emergency medical services between fully compensated, partially compensated, and non-compensated/volunteer samples.

Science.gov (United States)

Blau, Gary; Chapman, Susan; Gibson, Gregory; Bentley, Melissa A

2011-01-01

The purpose of our study was to investigate the importance of different items as reasons for leaving the Emergency Medical Service (EMS) profession. An exit survey was returned by three distinct EMS samples: 127 full compensated, 45 partially compensated and 72 non-compensated/volunteer respondents, who rated the importance of 17 different items for affecting their decision to leave EMS. Unfortunately, there were a high percentage of "not applicable" responses for 10 items. We focused on those seven items that had a majority of useable responses across the three samples. Results showed that the desire for better pay and benefits was a more important reason for leaving EMS for the partially compensated versus fully compensated respondents. Perceived lack of advancement opportunity was a more important reason for leaving for the partially compensated and volunteer groups versus the fully compensated group. Study limitations are discussed and suggestions for future research offered.

Neuromuscular compensation mechanisms in vocal fold paralysis and paresis.

Science.gov (United States)

Dewan, Karuna; Vahabzadeh-Hagh, Andrew; Soofer, Donna; Chhetri, Dinesh K

2017-07-01

Vocal fold paresis and paralysis are common conditions. Treatment options include augmentation laryngoplasty and voice therapy. The optimal management for this condition is unclear. The objective of this study was to assess possible neuromuscular compensation mechanisms that could potentially be used in the treatment of vocal fold paresis and paralysis. In vivo canine model. In an in vivo canine model, we examined three conditions: 1) unilateral right recurrent laryngeal nerve (RLN) paresis and paralysis, 2) unilateral superior laryngeal nerve (SLN) paralysis, and 3) unilateral vagal nerve paresis and paralysis. Phonatory acoustics and aerodynamics were measured in each of these conditions. Effective compensation was defined as improved acoustic and aerodynamic profile. The most effective compensation for all conditions was increasing RLN activation and decreasing glottal gap. Increasing RLN activation increased the percentage of possible phonatory conditions that achieved phonation onset. SLN activation generally led to decreased number of total phonation onset conditions within each category. Differential effects of SLN (cricothyroid [CT] muscle) activation were seen. Ipsilateral SLN activation could compensate for RLN paralysis; normal CT compensated well in unilateral SLN paralysis; and in vagal paresis/paralysis, contralateral SLN and RLN displayed antagonistic relationships. Methods to improve glottal closure should be the primary treatment for large glottal gaps. Neuromuscular compensation is possible for paresis. This study provides insights into possible compensatory mechanisms in vocal fold paresis and paralysis. NA Laryngoscope, 127:1633-1638, 2017. © 2017 The American Laryngological, Rhinological and Otological Society, Inc.

Whiplash and the compensation hypothesis.

Science.gov (United States)

Spearing, Natalie M; Connelly, Luke B

2011-12-01

Review article. To explain why the evidence that compensation-related factors lead to worse health outcomes is not compelling, either in general, or in the specific case of whiplash. There is a common view that compensation-related factors lead to worse health outcomes ("the compensation hypothesis"), despite the presence of important, and unresolved sources of bias. The empirical evidence on this question has ramifications for the design of compensation schemes. Using studies on whiplash, this article outlines the methodological problems that impede attempts to confirm or refute the compensation hypothesis. Compensation studies are prone to measurement bias, reverse causation bias, and selection bias. Errors in measurement are largely due to the latent nature of whiplash injuries and health itself, a lack of clarity over the unit of measurement (specific factors, or "compensation"), and a lack of appreciation for the heterogeneous qualities of compensation-related factors and schemes. There has been a failure to acknowledge and empirically address reverse causation bias, or the likelihood that poor health influences the decision to pursue compensation: it is unclear if compensation is a cause or a consequence of poor health, or both. Finally, unresolved selection bias (and hence, confounding) is evident in longitudinal studies and natural experiments. In both cases, between-group differences have not been addressed convincingly. The nature of the relationship between compensation-related factors and health is unclear. Current approaches to testing the compensation hypothesis are prone to several important sources of bias, which compromise the validity of their results. Methods that explicitly test the hypothesis and establish whether or not a causal relationship exists between compensation factors and prolonged whiplash symptoms are needed in future studies.

Use of compensation and incentives in siting low-level radioactive waste disposal facilities

International Nuclear Information System (INIS)

Smith, T.P.; Jaffe, M.

1984-09-01

In discussing the use of compensation and incentives in siting low-level radioactive waste disposal facilities, chapters are devoted to: compensation and incentives in disposal facility siting (definitions and effects of compensation and incentives and siting decisions involving the use of compensation and incentives); the impacts of regional and state low-level radioactive waste facilities; the legal framework of compensation; and recommendations regarding the use of compensation

Harmonic Resonance Damping with a Hybrid Compensation System in Power Systems with Dispersed Generation

DEFF Research Database (Denmark)

Chen, Zhe; Pedersen, John Kim; Blaabjerg, Frede

2004-01-01

A hybrid compensation system consisting of an active filter and a group of distributed passive filters has been studied previously. The passive filters are used for each distorting load or Dispersed Generation (DG) unit to remove major harmonics and provide reactive power compensation. The active...... filter is connected in parallel with the distributed passive filters and loads/DGs to correct the system unbalance and remove the remaining harmonic components. The effectiveness of the presented compensation system has also been demonstrated. This paper studies the performance of the hybrid compensation...... demonstrated that the harmonic resonance can be damped effectively. The hybrid filter system is an effective compensation system for dispersed generation systems. In the compensation system, the passive filters are mainly responsible for main harmonic and reactive power compensation of each individual load/ DG...

Compensation and benefit sharing: Why resettlement policies and practices must be reformed

Institute of Scientific and Technical Information of China (English)

Michael M. Cernea

2008-01-01

Many public and private sector projects, such as hydropower dams or mines, trigger forced population displacement but fail to resettle people sustainably and instead cause their impoverishment. Social science research has found that one root cause of such failures and of impoverishment is asset dispossession and the insufficient financing of resettlement. Most governments, however, state that (1) compensation alone is sufficient for restoring the income and livelihood of those displaced, and (2) resources to supplement compensation with additional financing are not available. The author critiques and rejects these positions. He offers a theoretical analysis of the limits and flaws of compensation payments for expropriated assets, and argues that resources are available for supplementing compensation with financial investments for resettlers' development. The sources for supplementary financing are the economic rent (windfall profits) generated by natural resource projects such as hydropower or mining and the regular stream of benefits generated by all projects that require resettlement. Further, the author argues that financial investments in resettlers' welfare are indispensable and that benefit sharing is feasible. Therefore, both should become basic principles of resettlement legislation and practice. In addition to theoretical analysis, the author documents with empirical evidence that some countries (China, Brazil, Canada, Columbia and Japan) already make investments additional to compensation for post-displacement reconstruction. The author sums up his argument in these key points:(1) Compensation alone cannot prevent the impoverishment of resettlers and cannot in itself restore and improve their livelihoods;(2) Additional financing is needed for direct investments in resettlement with development;(3) Compensation levels must be increased;(4) Financing resources are available in most cases for investing in resettlers' development, but allocation of

Compensation and benefit sharing: Why resettlement policies and practices must be reformed

Directory of Open Access Journals (Sweden)

Michael M. Cernea

2008-03-01

Full Text Available Many public and private sector projects, such as hydropower dams or mines, trigger forced population displacement but fail to resettle people sustainably and instead cause their impoverishment. Social science research has found that one root cause of such failures and of impoverishment is asset dispossession and the insufficient financing of resettlement. Most governments, however, state that (1 compensation alone is sufficient for restoring the income and livelihood of those displaced, and (2 resources to supplement compensation with additional financing are not available. The author critiques and rejects these positions. He offers a theoretical analysis of the limits and flaws of compensation payments for expropriated assets, and argues that resources are available for supplementing compensation with financial investments for resettlers’ development. The sources for supplementary financing are the economic rent (windfall profits generated by natural resource projects such as hydropower or mining and the regular stream of benefits generated by all projects that require resettlement. Further, the author argues that financial investments in resettlers’ welfare are indispensable and that benefit sharing is feasible. Therefore, both should become basic principles of resettlement legislation and practice. In addition to theoretical analysis, the author documents with empirical evidence that some countries (China, Brazil, Canada, Columbia and Japan already make investments additional to compensation for post-displacement reconstruction. The author sums up his argument in these key points: (1Compensation alone cannot prevent the impoverishment of resettlers and cannot in itself restore and improve their livelihoods; (2Additional financing is needed for direct investments in resettlement with development; (3Compensation levels must be increased; (4Financing resources are available in most cases for investing in resettlers’ development, but

Manufacture of sockets of volume compensators in nuclear power plants

International Nuclear Information System (INIS)

Andreev, V.P.; Tshekotilo, L.V.; Shevtshenko, N.T.; Sevruk, A.N.; Wolacek, W.J.; Irsicek, L.; Vrbensky, J.

1982-01-01

Experience is reported with regard to electroslag casting of sockets of volume compensators or steam separators used in nuclear power plants. According to the method the raw pieces are casted directly at the surface of the enclosures

National regulations for diagnostics in health surveillance, therapy and compensation of hand-transmitted vibration injury in Japan.

Science.gov (United States)

Yamada, Shin'ya

2002-01-01

During the period of technological innovation and rapid economic development, portable power tools were introduced on a large scale in Japan. Vibration disease from the operation of those tools and its prevention and therapy became urgent social problems in the 1970s. This paper aims to introduce national regulations in Japan for diagnostics in the health surveillance, certification, therapy and compensation of vibration disease and evaluates them in the present perspective. Relevant laws, regulations and administrative directives were described in chronological order. Effect of those laws, regulations and directives were evaluated by statistics. Relevant regulations were established in 1947 and were revised in the 1960s and 1970s. According to those regulations, administrative directives were issued. Relevant vibration-disease statistics improved from the 1970s to 1990s. The annual ratio of workers examined was 95% to 100% in national forests (NFs), 47.3% in 1980 and 40.8% in 1990 in private industry (PI). The number of workers certified in NFs was 1,796 from 1971-1975, with a decrease to nine from 1991-1995, while in PI there were 9,783 from 1976-1980, decreasing to 2,331 from 1991-1995. However, in the construction industry the number increased again in the 1990s. The top four workers certified by the type of tool from 1994-1997 were operators of rock drills, chainsaws, pick hammers and concrete vibrators. The annual number of workers under treatment (at highest level) was 3,605 (1982; NFs) and 13,501 (1987; PI), with a decrease to 3,481 (1997; NFs) and 8,958 (1997; PI). Regulations for compensation covered 3,670 workers from 1965 to 1997 (NFs) and 22,723 from 1976 to 1997 (PI) in medical treatment benefits, and 189 (NFs) and 15,448 (PI) in disability benefits during the same term. The national regulations developed in Japan since 1965 for health surveillance, certification, therapy and compensation of hand-transmitted vibration disease have proven effective for

Procedural justice and quality of life in compensation processes

NARCIS (Netherlands)

Elbers, N.A.; Akkermans, A.J.; Cuijpers, P.; Bruinvels, D.J.

2013-01-01

Background: There is considerable evidence that being involved in compensation processes has a negative impact on claimants' health. Previous studies suggested that this negative effect is caused by a stressful compensation process: claimants suffered from a lack of communication, a lack of

Evaluation and compensation of steady gas flow force on the high-pressure electro-pneumatic servo valve direct-driven by voice coil motor

International Nuclear Information System (INIS)

Li, Baoren; Gao, Longlong; Yang, Gang

2013-01-01

Highlights: ► A novel energy saving high-pressure electro-pneumatic servo valve is presented. ► An evaluated method for steady gas flow forces on pneumatic valves is proposed. ► Gas jet angles at the orifices for the valve are larger than 69° commonly used. ► The steady gas flow force is strongly nonlinear with valve opening. ► The steady gas flow force is compensated and the aim at energy saving is realized. - Abstract: A novel voice coil motor (VCM) direct drive single stage high-pressure pneumatic servo valve is designed, and then the steady gas flow force acting on the spool of the servo valve is investigated by numerical simulation and experimental methods in this paper. At present, many studies about flow force are concentrated mainly on hydraulic valves, but rarely on pneumatic valves. However, the velocity of gas is up to sonic when high-pressure gas flows through the servo valve orifice. And therefore, the steady gas flow force, generated by high pressure and high speed gas flow, cannot be neglected and is an important disturbance for the VCM direct-drive single stage high-pressure pneumatic servo valve. Consequently, the numerical simulation with computational fluid dynamics (CFD) is adopted to analyze the flow filed, jet angles, and steady gas flow forces for the servo valve with different valve openings and inlet pressures. The experimental study is performed to evaluate and confirm the numerical analysis. Then the compensated approach is proposed to reduce the steady gas flow force for the servo valve, changing the angle of non-metering port designed in the valve sleeve to the spool axis. The results demonstrate that the presented numerical analysis method is validated, the gas jet angle for the servo valve orifice is more than 69° and varies with different spool openings, and the steady gas flow force is nonlinear with valve opening and linear with inlet pressure when the outlet boundary is atmospheric pressure. Moreover, the steady gas

Forest Ecosystem Services and Eco-Compensation Mechanisms in China

Science.gov (United States)

Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

2011-12-01

Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

Forest ecosystem services and eco-compensation mechanisms in China.

Science.gov (United States)

Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

2011-12-01

Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

Stock-based Compensation Plans and Employee Incentives

OpenAIRE

Jan Zabojnik

2014-01-01

Standard principal-agent theory predicts that large firms should not use employee stock options and other stock-based compensation to provide incentives to non-executive employees. Yet, business practitioners appear to believe that stock-based compensation improves incentives, and mounting empirical evidence points to the same conclusion. This paper provides an explanation for why stock-based incentives can be effective. In the model of this paper, employee stock options complement individual...

Compensation of the detector capacitance presented to charge-sensitive preamplifiers using the Miller effect

Energy Technology Data Exchange (ETDEWEB)

Kwon, Inyong, E-mail: iykwon@umich.edu [University of Michigan, Ann Arbor, MI (United States); Kang, Taehoon, E-mail: thnkang@umich.edu [University of Michigan, Ann Arbor, MI (United States); Wells, Byron T., E-mail: wells@galtresearch.com [Galt LLC, Ypsilanti, MI (United States); D’Aries, Lawrence J., E-mail: lawrence.j.daries.civ@mail.mil [Picatinny Arsenal, Rockaway Township, NJ (United States); Hammig, Mark D., E-mail: hammig@umich.edu [University of Michigan, Ann Arbor, MI (United States)

2015-06-01

This paper describes an integrated circuit design for a modified charge-sensitive amplifier (CSA) that compensates for the effect of capacitance presented by nuclear radiation detectors and other sensors. For applications that require large area semiconductor detectors or for those semiconductor sensors derived from high permittivity materials such as PbSe, the detector capacitance can degrade the system gain and bandwidth of a front-end preamplifier, resulting in extended rise times and attenuated output voltage signals during pulse formation. In order to suppress the effect of sensor capacitance, we applied a bootstrap technique into a traditional CSA. The technique exploits the Miller effect by reducing the effective voltage difference between the two sides of a radiation detector which minimizes the capacitance presented to the differential common-source amplifier. This new configuration is successfully designed to produce effective gain even at high detector capacitance. The entire circuit, including a core CSA with feedback components and a bootstrap amplifier, are implemented in a 0.18 μm CMOS process with a 3.3 V supply voltage. - Highlights: • A modified CSA was implemented for detector capacitance compensation. • Increasing detector capacitance degrades gain and rise time. • A bootstrap amplifier exploiting the Miller effect is described. • It allows using large area radiation sensors for high radiation-interaction rates. • Intensive noise analyses show that SNR is much better with the technique.

Directive concerning compensation payable for reasons of equity for loss incurred with certain vegetable species (Directive on equitableness, vegetables) as of June 2, 1986

Energy Technology Data Exchange (ETDEWEB)

1986-06-12

For damage in the field of agriculture caused by the Chernobyl reactor accident which is not within the scope of the Atomic Energy Act, but to be treated under the Farming Law, compensation is paid ex gratia, for reasons of equity. Compensation is paid for loss incurred by the 31st of May 1986 at the latest, as a result of decisions or recommendations issued by the competent public authorities, with reference to the following vegetables: Celery, broccoli, Chinese cabbage, savoy cabbage, onions, kohlrabi, parsley, little radish, radish, rhubarb, chives, white cabbage, herbs cultivated like vegetables for large-scale sale.

Illumination compensation in ground based hyperspectral imaging

Science.gov (United States)

Wendel, Alexander; Underwood, James

2017-07-01

Hyperspectral imaging has emerged as an important tool for analysing vegetation data in agricultural applications. Recently, low altitude and ground based hyperspectral imaging solutions have come to the fore, providing very high resolution data for mapping and studying large areas of crops in detail. However, these platforms introduce a unique set of challenges that need to be overcome to ensure consistent, accurate and timely acquisition of data. One particular problem is dealing with changes in environmental illumination while operating with natural light under cloud cover, which can have considerable effects on spectral shape. In the past this has been commonly achieved by imaging known reference targets at the time of data acquisition, direct measurement of irradiance, or atmospheric modelling. While capturing a reference panel continuously or very frequently allows accurate compensation for illumination changes, this is often not practical with ground based platforms, and impossible in aerial applications. This paper examines the use of an autonomous unmanned ground vehicle (UGV) to gather high resolution hyperspectral imaging data of crops under natural illumination. A process of illumination compensation is performed to extract the inherent reflectance properties of the crops, despite variable illumination. This work adapts a previously developed subspace model approach to reflectance and illumination recovery. Though tested on a ground vehicle in this paper, it is applicable to low altitude unmanned aerial hyperspectral imagery also. The method uses occasional observations of reference panel training data from within the same or other datasets, which enables a practical field protocol that minimises in-field manual labour. This paper tests the new approach, comparing it against traditional methods. Several illumination compensation protocols for high volume ground based data collection are presented based on the results. The findings in this paper are

effect of land policy on compensation for environmental damage

African Journals Online (AJOL)

Osondu

2013-02-21

Feb 21, 2013 ... The paper argues that compensation for compulsory acquisition as ... industry activities on environmental assets in the .... the oil companies operating in the Niger Delta ... Air Quality, Precipitation and Corrosion Studies of.

On the compensating filter in pulmonary hilar tomography

International Nuclear Information System (INIS)

Okayama, Akio; Nakanishi, Takashi; Fujikawa, Tsuyoshi

1980-01-01

It is difficult to make the optimal density for all area of the pulmonary hilar region on a same film in conventional tomography. But, it is possible to observe all area of the pulmonary hilar region on a same film by equalizing the uneven density of pulmonary hilar region with compensating filter. On this study, the filter which could compensated density in all shifts of Polytome U was constructed and discussed about diagnostic evaluation for those shifts. As a results, by using this filter, the density for all area of the pulmonary hilar region in all shifts of Polytome U could be compensated and grasp the mutral relation of its region. As a conclusion, using this filter is useful method to diagnose pulmonary hilar region. If it is possible to make a patient enough hold a breath, using circular shift is better than other's. If it is difficult to do so, it can not help using linear shift. In such a case, it shall be taken a tomograph in direction of linear shift fitting the object. (author)

Reactive Balance Control in Response to Perturbation in Unilateral Stance: Interaction Effects of Direction, Displacement and Velocity on Compensatory Neuromuscular and Kinematic Responses.

Directory of Open Access Journals (Sweden)

Kathrin Freyler

Full Text Available Unexpected sudden perturbations challenge postural equilibrium and require reactive compensation. This study aimed to assess interaction effects of the direction, displacement and velocity of perturbations on electromyographic (EMG activity, centre of pressure (COP displacement and joint kinematics to detect neuromuscular characteristics (phasic and segmental and kinematic strategies of compensatory reactions in an unilateral balance paradigm. In 20 subjects, COP displacement and velocity, ankle, knee and hip joint excursions and EMG during short (SLR, medium (MLR and long latency response (LLR of four shank and five thigh muscles were analysed during random surface translations varying in direction (anterior-posterior (sagittal plane, medial-lateral (frontal plane, displacement (2 vs. 3 cm and velocity (0.11 vs. 0.18 m/s of perturbation when balancing on one leg on a movable platform. Phases: SLR and MLR were scaled to increased velocity (P<0.05; LLR was scaled to increased displacement (P<0.05. Segments: phasic interrelationships were accompanied by segmental distinctions: distal muscles were used for fast compensation in SLR (P<0.05 and proximal muscles to stabilise in LLR (P<0.05. Kinematics: ankle joints compensated for both increasing displacement and velocity in all directions (P<0.05, whereas knee joint deflections were particularly sensitive to increasing displacement in the sagittal (P<0.05 and hip joint deflections to increasing velocity in the frontal plane (P<0.05. COP measures increased with increasing perturbation velocity and displacement (P<0.05. Interaction effects indicate that compensatory responses are based on complex processes, including different postural strategies characterised by phasic and segmental specifications, precisely adjusted to the type of balance disturbance. To regain balance after surface translation, muscles of the distal segment govern the quick regain of equilibrium; the muscles of the proximal limb

Inertia compensated force and pressure sensors

Energy Technology Data Exchange (ETDEWEB)

Bill, B.; Engeler, P.; Gossweiler, C. [Kistler Instrumente AG, Winterthur (Switzerland)

2001-07-01

Any moving structure is affected by inertial effects. In case of force and pressure sensors, inertial effects cause measurement errors. The paper deals with novel signal conditioning methods and mechanical design features to minimize inertial effects. A novel solution for passive compensation of pressure sensors is presented. (orig.)

Effect of high-pitch dual-source CT to compensate motion artifacts: a phantom study.

Science.gov (United States)

Farshad-Amacker, Nadja A; Alkadhi, Hatem; Leschka, Sebastian; Frauenfelder, Thomas

2013-10-01

To evaluate the potential of high-pitch, dual-source computed tomography (DSCT) for compensation of motion artifacts. Motion artifacts were created using a moving chest/cardiac phantom with integrated stents at different velocities (from 0 to 4-6 cm/s) parallel (z direction), transverse (x direction), and diagonal (x and z direction combined) to the scanning direction using standard-pitch (SP) (pitch = 1) and high-pitch (HP) (pitch = 3.2) 128-detector DSCT (Siemens, Healthcare, Forchheim, Germany). The scanning parameters were (SP/HP): tube voltage, 120 kV/120 kV; effective tube current time product, 300 mAs/500 mAs; and a pitch of 1/3.2. Motion artifacts were analyzed in terms of subjective image quality and object distortion. Image quality was rated by two blinded, independent observers using a 4-point scoring system (1, excellent; 2, good with minor object distortion or blurring; 3, diagnostically partially not acceptable; and 4, diagnostically not acceptable image quality). Object distortion was assessed by the measured changes of the object's outer diameter (x) and length (z) and a corresponding calculated distortion vector (d) (d = √(x(2) + z(2))). The interobserver agreement was excellent (k = 0.91). Image quality using SP was diagnostically not acceptable with any motion in x direction (scores 3 and 4), in contrast to HP DSCT where it remained diagnostic up to 2 cm/s (scores 1 and 2). For motion in the z direction only, image quality remained diagnostic for SP and HP DSCT (scores 1 and 2). Changes of the object's diameter (x), length (z), and distortion vectors (d) were significantly greater with SP (overall: x = 1.9 cm ± 1.7 cm, z = 0.6 cm ± 0.8 cm, and d = 1.4 cm ± 1.5 cm) compared to HP DSCT (overall: x = 0.1 cm ± 0.1 cm, z = 0.0 cm ± 0.1 cm, and d = 0.1 cm ± 0.1 cm; each P pitch DSCT significantly decreases motion artifacts in various directions and improves image quality. Copyright © 2013 AUR. Published by Elsevier Inc. All rights reserved.

The relationship between motivation, monetary compensation, and data quality among US- and India-based workers on Mechanical Turk.

Science.gov (United States)

Litman, Leib; Robinson, Jonathan; Rosenzweig, Cheskie

2015-06-01

In this study, we examined data quality among Amazon Mechanical Turk (MTurk) workers based in India, and the effect of monetary compensation on their data quality. Recent studies have shown that work quality is independent of compensation rates, and that compensation primarily affects the quantity but not the quality of work. However, the results of these studies were generally based on compensation rates below the minimum wage, and far below a level that was likely to play a practical role in the lives of workers. In this study, compensation rates were set around the minimum wage in India. To examine data quality, we developed the squared discrepancy procedure, which is a task-based quality assurance approach for survey tasks whose goal is to identify inattentive participants. We showed that data quality is directly affected by compensation rates for India-based participants. We also found that data were of a lesser quality among India-based than among US participants, even when optimal payment strategies were utilized. We additionally showed that the motivation of MTurk users has shifted, and that monetary compensation is now reported to be the primary reason for working on MTurk, among both US- and India-based workers. Overall, MTurk is a constantly evolving marketplace where multiple factors can contribute to data quality. High-quality survey data can be acquired on MTurk among India-based participants when an appropriate pay rate is provided and task-specific quality assurance procedures are utilized.

Optimization Of Chromaticity Compensation And Dynamic Aperture In MEIC Collider Rings

International Nuclear Information System (INIS)

Lin, Fanglei; Derbenev, Yaroslav; Morozov, Vasiliy; Zhang, Yuhong; Beard, Kevin

2012-01-01

The conceptual design of the Medium-energy Electron-Ion Collider (MEIC) at Jefferson Lab relies on an ultra-small beta-star to achieve high luminosities of up to 10 34 cm -2 s -1 . A low-beta insertion for interaction regions unavoidably induces large chromatic effects that demand a proper compensation. The present approach of chromatic compensation in the MEIC collider rings is based on a local correction scheme using two symmetric chromatic compensation blocks that includes families of sextupoles, and are placed in a beam extension area on both sides of a collision point. It can simultaneously compensate the first order chromaticity and chromatic beam smear at the IP without inducing significant second order aberrations. In this paper, we investigate both the momentum acceptance and dynamic aperture in the MEIC ion collider ring by considering the aberration effects up to the third order, such as amplitude dependent tune shift. We also explore the compensation of the third order effects by introducing families of octupoles in the extended beam area.

Verification and compensation of respiratory motion using an ultrasound imaging system

International Nuclear Information System (INIS)

Chuang, Ho-Chiao; Hsu, Hsiao-Yu; Chiu, Wei-Hung; Tien, Der-Chi; Wu, Ren-Hong; Hsu, Chung-Hsien

2015-01-01

Purpose: The purpose of this study was to determine if it is feasible to use ultrasound imaging as an aid for moving the treatment couch during diagnosis and treatment procedures associated with radiation therapy, in order to offset organ displacement caused by respiratory motion. A noninvasive ultrasound system was used to replace the C-arm device during diagnosis and treatment with the aims of reducing the x-ray radiation dose on the human body while simultaneously being able to monitor organ displacements. Methods: This study used a proposed respiratory compensating system combined with an ultrasound imaging system to monitor the compensation effect of respiratory motion. The accuracy of the compensation effect was verified by fluoroscopy, which means that fluoroscopy could be replaced so as to reduce unnecessary radiation dose on patients. A respiratory simulation system was used to simulate the respiratory motion of the human abdomen and a strain gauge (respiratory signal acquisition device) was used to capture the simulated respiratory signals. The target displacements could be detected by an ultrasound probe and used as a reference for adjusting the gain value of the respiratory signal used by the respiratory compensating system. This ensured that the amplitude of the respiratory compensation signal was a faithful representation of the target displacement. Results: The results show that performing respiratory compensation with the assistance of the ultrasound images reduced the compensation error of the respiratory compensating system to 0.81–2.92 mm, both for sine-wave input signals with amplitudes of 5, 10, and 15 mm, and human respiratory signals; this represented compensation of the respiratory motion by up to 92.48%. In addition, the respiratory signals of 10 patients were captured in clinical trials, while their diaphragm displacements were observed simultaneously using ultrasound. Using the respiratory compensating system to offset, the diaphragm

Hydro-Quebec to complete series compensation protection by 1995

Energy Technology Data Exchange (ETDEWEB)

Champagne, L

1991-09-01

Hydro-Quebec's 735-kV transmission system is characterized by remote hydroelectric power plants located far north of main load centers, making it difficult to maintain dynamic stability of the system in the case of faults. The utility is planning to install series compensation on its 735-kV network from 1992 to 1995 in order to correct for the reactive impedance of the transmission lines, thereby removing load electrically closer to the points of generation. Series compensation in the form of capacitor banks with overvoltage protection will be installed at line ends and will replace large numbers of conventional electromagnetic or electronic distance relays currently used as line protection equipment. Three Manicouagan-Levis lines and the Micoua-Laurentides line will be center-compensated at 17%. A total of thirty-seven 735-kV lines will be series-compensated at ca 40%. Two separate sets of tests were conducted to select the new series compensation system. Following a market study, eight systems of line protection relays were selected as most likely to operate on a series compensated system. All were performance tested on a transient network analyzer in a simulation involving all components of the 735-kV system with some exceptions. Relays singled out in standard tests were put to a series of more specific tests on the Abitibi-LaVerendrye line, where the largest number of relay malfunctions had been recorded. A current differential relay and a superimposed directional relay were recommended as the two primary protective systems to be installed. Backup protection will be provided by using one of the distance relays with memory polarization. 3 figs.

A study on multi-point gravity compensation of mirror bending system

International Nuclear Information System (INIS)

Sun Fuquan; Fu Yuan; Zhu Wanqian; Xue Song

2011-01-01

The sag of mirror due to gravity induces unacceptable slope errors in beamline mirror-bending system of a synchrotron radiation facility, and approaches must be found to eliminate the unwanted gravity effect. According to the beam bending theory, the multi-point gravity compensation method is applicable. Taking an example of the bent collimating mirror for the XAFS beam-line (BL14W) at Shanghai Synchrotron Radiation Facility (SSRF), the best position and value of the equilibrant were calculated through minimizing the gravity effect. With two, three and four points gravity compensation, slope errors were 0.179, 0.067 and 0.032 μrad,respectively, i.e.the multi-point gravity compensation is better than the two-point gravity compensation, which is used for the Phase I beamlines of SSRF. The four-point gravity compensation method reduces more slope error and stress due to four support points. (authors)

Kinetics and compensation effects during steam gasification of Fujian anthracite using viscose liquor as catalyst

Energy Technology Data Exchange (ETDEWEB)

Lin Ju; Zhang Ji-yu; Zhong Xue-qing [Fuzhou University, Fuzhou (China). Institute of Chemical Engineering and Technology

2009-08-15

Catalytic steam gasification kinetics of Fujian Youxi anthracite using viscose liquor as catalyst was investigated in an isothermal thermo-gravimetric analyzer under ambient pressure. Coal conversions versus reaction time with different viscose liquor concentrations (0-12% NaOH) were measured at the temperature range from 850 to 950{sup o}C. The research shows that the viscose liquor can greatly improve the gasification rate and carbon conversion. The Loading Saturation Level (LSL) of the viscose liquor within the experimental conditions was also determined. The catalytic steam gasification reaction can be well fitted by a shrinking-core model (SCM) and the reaction rate constants are obtained. The kinetic analysis indicates that the catalytic gasification exhibits a prominent compensation effect between the activation energy and the pre-exponential factor. The kinetic equation including the compensation effects for the catalytic steam gasification of Fujian Youxi anthracite using viscose liquor as catalyst is presented. 23 refs., 7 figs., 3 tabs.

Reactive Balance Control in Response to Perturbation in Unilateral Stance: Interaction Effects of Direction, Displacement and Velocity on Compensatory Neuromuscular and Kinematic Responses

Science.gov (United States)

Freyler, Kathrin; Gollhofer, Albert; Colin, Ralf; Brüderlin, Uli; Ritzmann, Ramona

2015-01-01

Unexpected sudden perturbations challenge postural equilibrium and require reactive compensation. This study aimed to assess interaction effects of the direction, displacement and velocity of perturbations on electromyographic (EMG) activity, centre of pressure (COP) displacement and joint kinematics to detect neuromuscular characteristics (phasic and segmental) and kinematic strategies of compensatory reactions in an unilateral balance paradigm. In 20 subjects, COP displacement and velocity, ankle, knee and hip joint excursions and EMG during short (SLR), medium (MLR) and long latency response (LLR) of four shank and five thigh muscles were analysed during random surface translations varying in direction (anterior-posterior (sagittal plane), medial-lateral (frontal plane)), displacement (2 vs. 3cm) and velocity (0.11 vs. 0.18m/s) of perturbation when balancing on one leg on a movable platform. Phases: SLR and MLR were scaled to increased velocity (Pjoints compensated for both increasing displacement and velocity in all directions (Pjoint deflections were particularly sensitive to increasing displacement in the sagittal (Pjoint deflections to increasing velocity in the frontal plane (P<0.05). COP measures increased with increasing perturbation velocity and displacement (P<0.05). Interaction effects indicate that compensatory responses are based on complex processes, including different postural strategies characterised by phasic and segmental specifications, precisely adjusted to the type of balance disturbance. To regain balance after surface translation, muscles of the distal segment govern the quick regain of equilibrium; the muscles of the proximal limb serve as delayed stabilisers after a balance disturbance. Further, a kinematic distinction regarding the compensation for balance disturbance indicated different plane- and segment-specific sensitivities with respect to the determinants displacement and velocity. PMID:26678061

Joint adaptive modulation and diversity combining with feedback error compensation

KAUST Repository

Choi, Seyeong; Hong-Chuan, Yang; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2009-01-01

This letter investigates the effect of feedback error on the performance of the joint adaptive modulation and diversity combining (AMDC) scheme which was previously studied with an assumption of error-free feedback channels. We also propose to utilize adaptive diversity to compensate for the performance degradation due to feedback error. We accurately quantify the performance of the joint AMDC scheme in the presence of feedback error, in terms of the average number of combined paths, the average spectral efficiency, and the average bit error rate. Selected numerical examples are presented and discussed to illustrate the effectiveness of the proposed feedback error compensation strategy with adaptive combining. It is observed that the proposed compensation strategy can offer considerable error performance improvement with little loss in processing power and spectral efficiency in comparison with the no compensation case. Copyright © 2009 IEEE.

Joint adaptive modulation and diversity combining with feedback error compensation

KAUST Repository

Choi, Seyeong

2009-11-01

This letter investigates the effect of feedback error on the performance of the joint adaptive modulation and diversity combining (AMDC) scheme which was previously studied with an assumption of error-free feedback channels. We also propose to utilize adaptive diversity to compensate for the performance degradation due to feedback error. We accurately quantify the performance of the joint AMDC scheme in the presence of feedback error, in terms of the average number of combined paths, the average spectral efficiency, and the average bit error rate. Selected numerical examples are presented and discussed to illustrate the effectiveness of the proposed feedback error compensation strategy with adaptive combining. It is observed that the proposed compensation strategy can offer considerable error performance improvement with little loss in processing power and spectral efficiency in comparison with the no compensation case. Copyright © 2009 IEEE.

An effective temperature compensation approach for ultrasonic hydrogen sensors

Science.gov (United States)

Tan, Xiaolong; Li, Min; Arsad, Norhana; Wen, Xiaoyan; Lu, Haifei

2018-03-01

Hydrogen is a kind of promising clean energy resource with a wide application prospect, which will, however, cause a serious security issue upon the leakage of hydrogen gas. The measurement of its concentration is of great significance. In a traditional approach of ultrasonic hydrogen sensing, a temperature drift of 0.1 °C results in a concentration error of about 250 ppm, which is intolerable for trace amount of gas sensing. In order to eliminate the influence brought by temperature drift, we propose a feasible approach named as linear compensation algorithm, which utilizes the linear relationship between the pulse count and temperature to compensate for the pulse count error (ΔN) caused by temperature drift. Experimental results demonstrate that our proposed approach is capable of improving the measurement accuracy and can easily detect sub-100 ppm of hydrogen concentration under variable temperature conditions.

Rehabilitation of compensable workplace injuries: effective payment models for quality vocational rehabilitation outcomes in a changing social landscape.

Science.gov (United States)

Matthews, Lynda R; Hanley, Francine; Lewis, Virginia; Howe, Caroline

2015-01-01

With social and economic costs of workplace injury on the increase, efficient payment models that deliver quality rehabilitation outcomes are of increasing interest. This paper provides a perspective on the issue informed by both refereed literature and published research material not available commercially (gray literature). A review of payment models, workers' compensation and compensable injury identified relevant peer-reviewed and gray literature that informed our discussion. Fee-for-service and performance-based payment models dominate the health and rehabilitation literature, each described as having benefits and challenges to achieving quality outcomes for consumers. There appears to be a movement toward performance-based payments in compensable workplace injury settings as they are perceived to promote time-efficient services and support innovation in rehabilitation practice. However, it appears that the challenges that arise for workplace-based rehabilitation providers and professionals when working under the various payment models, such as staff retention and quality of client-practitioner relationship, are absent from the literature and this could lead to flawed policy decisions. Robust evidence of the benefits and costs associated with different payment models - from the perspectives of clients/consumers, funders and service providers - is needed to inform best practice in rehabilitation of compensable workplace injuries. Available but limited evidence suggests that payment models providing financial incentives for stakeholder-agreed vocational rehabilitation outcomes tend to improve service effectiveness in workers' compensation settings, although there is little evidence of service quality or client satisfaction. Working in a system that identifies payments for stakeholder-agreed outcomes may be more satisfying for rehabilitation practitioners in workers' compensation settings by allowing more clinical autonomy and innovative practice. Researchers

Options in Compensation

DEFF Research Database (Denmark)

Flor, Christian Riis; Frimor, Hans; Munk, Claus

2014-01-01

We derive the optimal compensation contract in a principal–agent setting in which outcome is used to provide incentives for both effort and risky investments. To motivate investment, optimal compensation entails rewards for high as well as low outcomes, and it is increasing at the mean outcome...

RELIABILITY OF LENTICULAR EXPANSION COMPENSATORS

Directory of Open Access Journals (Sweden)

Gabriel BURLACU,

2011-11-01

Full Text Available Axial lenticular compensators are made to take over the longitudinal heat expansion, shock , vibration and noise, made elastic connections for piping systems. In order to have a long life for installations it is necessary that all elements, including lenticular compensators, have a good reliability. This desire can be did by technology of manufactoring and assembly of compensators, the material for lenses and by maintenance.of compensator

On techniques for angle compensation in nonideal iris recognition.

Science.gov (United States)

Schuckers, Stephanie A C; Schmid, Natalia A; Abhyankar, Aditya; Dorairaj, Vivekanand; Boyce, Christopher K; Hornak, Lawrence A

2007-10-01

The popularity of the iris biometric has grown considerably over the past two to three years. Most research has been focused on the development of new iris processing and recognition algorithms for frontal view iris images. However, a few challenging directions in iris research have been identified, including processing of a nonideal iris and iris at a distance. In this paper, we describe two nonideal iris recognition systems and analyze their performance. The word "nonideal" is used in the sense of compensating for off-angle occluded iris images. The system is designed to process nonideal iris images in two steps: 1) compensation for off-angle gaze direction and 2) processing and encoding of the rotated iris image. Two approaches are presented to account for angular variations in the iris images. In the first approach, we use Daugman's integrodifferential operator as an objective function to estimate the gaze direction. After the angle is estimated, the off-angle iris image undergoes geometric transformations involving the estimated angle and is further processed as if it were a frontal view image. The encoding technique developed for a frontal image is based on the application of the global independent component analysis. The second approach uses an angular deformation calibration model. The angular deformations are modeled, and calibration parameters are calculated. The proposed method consists of a closed-form solution, followed by an iterative optimization procedure. The images are projected on the plane closest to the base calibrated plane. Biorthogonal wavelets are used for encoding to perform iris recognition. We use a special dataset of the off-angle iris images to quantify the performance of the designed systems. A series of receiver operating characteristics demonstrate various effects on the performance of the nonideal-iris-based recognition system.

12 CFR 715.9 - Assistance from outside, compensated person.

Science.gov (United States)

2010-01-01

... behalf of a credit union shall not be related by blood or marriage to any management employee, member of... credit union. (b) Engagement letter. The engagement of a compensated auditor to perform all or a portion... engagement letter. In all cases, the engagement must be contracted directly with the Supervisory Committee...

effect of land policy on compensation for environmental damage

African Journals Online (AJOL)

Osondu

2013-02-21

Feb 21, 2013 ... compensation based on the provisions of Nigeria's Land Use Act of 1978, which is the .... material wealth. ... either by the grant of an oil pipeline licence or by ... Table 2 Estimated lifespan of selected tree crops in Nigeria.

Private equity fund compensation contracts and their incentive effects

NARCIS (Netherlands)

Phalippou, L.

2009-01-01

This article describes compensation contracts in private equity. It shows that they may not align interest between the investors and fund managers as much as commonly thought. Certain clauses appear as potentially hazardous for investors and others exacerbate conflicts of interest.

Space charge compensation in the Linac4 low energy beam transport line with negative hydrogen ions

Energy Technology Data Exchange (ETDEWEB)

Valerio-Lizarraga, Cristhian A., E-mail: cristhian.alfonso.valerio.lizarraga@cern.ch [CERN, Geneva (Switzerland); Departamento de Investigación en Física, Universidad de Sonora, Hermosillo (Mexico); Lallement, Jean-Baptiste; Lettry, Jacques; Scrivens, Richard [CERN, Geneva (Switzerland); Leon-Monzon, Ildefonso [Facultad de Ciencias Fisico-Matematicas, Universidad Autónoma de Sinaloa, Culiacan (Mexico); Midttun, Øystein [CERN, Geneva (Switzerland); University of Oslo, Oslo (Norway)

2014-02-15

The space charge effect of low energy, unbunched ion beams can be compensated by the trapping of ions or electrons into the beam potential. This has been studied for the 45 keV negative hydrogen ion beam in the CERN Linac4 Low Energy Beam Transport using the package IBSimu [T. Kalvas et al., Rev. Sci. Instrum. 81, 02B703 (2010)], which allows the space charge calculation of the particle trajectories. The results of the beam simulations will be compared to emittance measurements of an H{sup −} beam at the CERN Linac4 3 MeV test stand, where the injection of hydrogen gas directly into the beam transport region has been used to modify the space charge compensation degree.

Nuclear damage compensation and energy reform

International Nuclear Information System (INIS)

Yokemoto, Masafumi

2013-01-01

Nuclear damage compensation and energy reform were closely related. Nuclear damage compensation cost should be part of generation cost of nuclear power. Extend of nuclear damage compensation was limited by compensation standard of Tokyo Electric Power Co. (TEPCO) following guidelines of Dispute Reconciliation Committee for Nuclear Damage Compensation. TEPCO had already paid compensation of about two trillion yen until now, which was only a part of total damage compensation cost. TEPCO had been provided more than 3.4 trillion yen by Nuclear Damage Liability Facilitation Cooperation, which would be put back by nuclear operators including TEPCO. TEPCO could obtain present raising funds and try to reconstruct business with restart of nuclear power, which might disturb energy reform. Present nuclear damage compensation scheme had better be reformed with learning more from Minamata disease case in Japan. (T. Tanaka)

Price Elasticities of Food Demand: Compensated vs Uncompensated.

Science.gov (United States)

Clements, Kenneth W; Si, Jiawei

2016-11-01

Two recent studies have provided a comprehensive review/summary of a large number of estimates of the price elasticity of food consumption using a meta-regression approach. In this letter, we introduce a way of removing the income effect from these elasticities to recover the compensated elasticities. Although the income effect is small, the compensated elasticities vary by income group. Both types of elasticity should possibly be considered when assessing the impact of policy changes on food consumption. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Depth compensating calculation method of computer-generated holograms using symmetry and similarity of zone plates

Science.gov (United States)

Wei, Hui; Gong, Guanghong; Li, Ni

2017-10-01

Computer-generated hologram (CGH) is a promising 3D display technology while it is challenged by heavy computation load and vast memory requirement. To solve these problems, a depth compensating CGH calculation method based on symmetry and similarity of zone plates is proposed and implemented on graphics processing unit (GPU). An improved LUT method is put forward to compute the distances between object points and hologram pixels in the XY direction. The concept of depth compensating factor is defined and used for calculating the holograms of points with different depth positions instead of layer-based methods. The proposed method is suitable for arbitrary sampling objects with lower memory usage and higher computational efficiency compared to other CGH methods. The effectiveness of the proposed method is validated by numerical and optical experiments.

Poster - 49: Assessment of Synchrony respiratory compensation error for CyberKnife liver treatment

International Nuclear Information System (INIS)

Liu, Ming; Cygler, Joanna; Vandervoort, Eric

2016-01-01

The goal of this work is to quantify respiratory motion compensation errors for liver tumor patients treated by the CyberKnife system with Synchrony tracking, to identify patients with the smallest tracking errors and to eventually help coach patient’s breathing patterns to minimize dose delivery errors. The accuracy of CyberKnife Synchrony respiratory motion compensation was assessed for 37 patients treated for liver lesions by analyzing data from system logfiles. A predictive model is used to modulate the direction of individual beams during dose delivery based on the positions of internally implanted fiducials determined using an orthogonal x-ray imaging system and the current location of LED external markers. For each x-ray pair acquired, system logfiles report the prediction error, the difference between the measured and predicted fiducial positions, and the delivery error, which is an estimate of the statistical error in the model overcoming the latency between x-ray acquisition and robotic repositioning. The total error was calculated at the time of each x-ray pair, for the number of treatment fractions and the number of patients, giving the average respiratory motion compensation error in three dimensions. The 99 th percentile for the total radial error is 3.85 mm, with the highest contribution of 2.79 mm in superior/inferior (S/I) direction. The absolute mean compensation error is 1.78 mm radially with a 1.27 mm contribution in the S/I direction. Regions of high total error may provide insight into features predicting groups of patients with larger or smaller total errors.

Poster - 49: Assessment of Synchrony respiratory compensation error for CyberKnife liver treatment

Energy Technology Data Exchange (ETDEWEB)

Liu, Ming [Carleton University (Canada); Cygler, Joanna [The Ottawa Hospital Cancer Centre, Carleton University, Ottawa University (Canada); Vandervoort, Eric [The Ottawa Hospital Cancer Centre, Ottawa University (Canada)

2016-08-15

The goal of this work is to quantify respiratory motion compensation errors for liver tumor patients treated by the CyberKnife system with Synchrony tracking, to identify patients with the smallest tracking errors and to eventually help coach patient’s breathing patterns to minimize dose delivery errors. The accuracy of CyberKnife Synchrony respiratory motion compensation was assessed for 37 patients treated for liver lesions by analyzing data from system logfiles. A predictive model is used to modulate the direction of individual beams during dose delivery based on the positions of internally implanted fiducials determined using an orthogonal x-ray imaging system and the current location of LED external markers. For each x-ray pair acquired, system logfiles report the prediction error, the difference between the measured and predicted fiducial positions, and the delivery error, which is an estimate of the statistical error in the model overcoming the latency between x-ray acquisition and robotic repositioning. The total error was calculated at the time of each x-ray pair, for the number of treatment fractions and the number of patients, giving the average respiratory motion compensation error in three dimensions. The 99{sup th} percentile for the total radial error is 3.85 mm, with the highest contribution of 2.79 mm in superior/inferior (S/I) direction. The absolute mean compensation error is 1.78 mm radially with a 1.27 mm contribution in the S/I direction. Regions of high total error may provide insight into features predicting groups of patients with larger or smaller total errors.

Autonomous Voltage Unbalance Compensation in an Islanded Droop-Controlled Microgrid

DEFF Research Database (Denmark)

Savaghebi, Mehdi; Jalilian, Alireza; Vasquez, Juan Carlos

2013-01-01

Recently, there is an increasing interest in using distributed generators (DGs) not only to inject power into the grid, but also to enhance the power quality. In this paper, a stationary-frame control method for voltage unbalance compensation in an islanded microgrid is proposed. This method...... is based on the proper control of DGs interface converters. The DGs are controlled to compensate voltage unbalance autonomously while share the compensation effort and also active and reactive power, properly. The control system of the DGs mainly consists of active and reactive power droop controllers......, virtual impedance loop, voltage and current controllers and unbalance compensator. The design approach of the control system is discussed in detail and simulation and experimental results are presented. The results demonstrate the effectiveness of the proposed method in compensation of voltage unbalance....

Does whom you work with matter? Effects of referent group gender and age composition on managers' compensation.

Science.gov (United States)

Ostroff, Cheri; Atwater, Leanne E

2003-08-01

Much research has examined gender and age effects on compensation, concluding that a wage gap exists favoring men and negative stereotypes against older workers persist. Although the effect of an employee's gender or age has been widely studied, little work has examined the impact of the demographic characteristics of a focal employee's immediate referent groups (e.g., subordinates, peers, or supervisors) on pay. The effect of the gender and age composition of a focal manager's subordinates, peers, and supervisor on the manager's compensation levels was investigated in a sample of 2,178 managers across a wide range of organizations and functional areas. After controlling for a number of human capital variables, results indicated that not only does a wage gap favoring men exist, but also managerial pay is lower when managers' referent groups are largely female, when subordinates are outside the prime age group, and when peers and supervisors are younger.

Dimensional verification and location of the reactive static compensator in 220 kV; Verificacion del dimensionamiento y ubicacion del compensador estatico de reactivos en 220 kV

Energy Technology Data Exchange (ETDEWEB)

Fernandez Krekeler, Ubaldo [Administracion Nacional de Electricidad (ANDE), Asuncion (Paraguay)]. E-mail: ufernandez@ieee.org; Cardozo Sanchez, Freddy [Mirant Americas (United States)

2001-07-01

This work presents a determination verification of the compensation range and the location of reactive static compensator (RSC) in 220 kV. The verification is accomplished by analyses of the RSC effects in relation to the losses, loading and system voltage stability. The needed compensation range is investigated in full details, whereas that the required conversion level is directly related to this range. It is concluded that the RSC installation, foreseen for 2002, might be postponed for 2005/10 still without reinforcements in 500 kV. The Limpio substation seems to be the more suitable location in relation to the most analysed cases.

Coordination mechanism of SaaS service supply chain: Based on compensation contracts

Directory of Open Access Journals (Sweden)

Yanli Guo

2013-09-01

Full Text Available Purpose: The purpose of this paper is to build new contracts theories of SaaS service supply chain. Software as a Service (SaaS has become a hot topic in this industry . Compared with traditional manufacturing supply chain and general service supply chain, the new IT service supply chain which based on SaaS has characteristics of both service and IT. And SaaS is completely different from traditional software package model. Therefore the classic contracts, which be widely used in traditional manufacturing supply chain, can’t be directly applied in SaaS service supply chain. The necessary way of IT services developing is to study the SaaS service supply chain combining with characteristics of SaaS. Therefore, It focuses on the coordination of SaaS service supply chain. Design/methodology/approach: It tries to answer the following question: how do the ISV motivate SaaS operators to improve the service level through effective contracts mechanism under conditions of asymmetric information. In order to answer these questions, this paper does some researches including: Under the conditions of information asymmetry, supposing the service level (is related to the degree of effort of SaaS operator was private information, we construct model of compensation contract, i.e., to motivate SaaS operator to improve service level through transfer payments of compensation price. Findings and Originality/value: The study finds out that when ISV get to “positive feedback”, instead of the traditional market equilibrium, compensation contract (linear can coordinate satisfactorily the SaaS service supply chain. In the point of “positive feedback”, the marginal revenue equals the marginal cost, but it is not the equilibrium of ISV’profit-maximization. Research limitations/implications: There are some limitations in this research. In the linear compensation contracts, the compensation price is fixed value. If in the contract, we can create a change value

voltage compensation using artificial neural network

African Journals Online (AJOL)

Offor Theophilos

Simulation results showed that DVR is effective in compensating for ... shutdown of heavy equipment, switching operations etc, ... station were carried out in MatLab 2013 application. ... semiconductor in a pulse width modulation (PWM).

Springback Simulation and Tool Surface Compensation Algorithm for Sheet Metal Forming

International Nuclear Information System (INIS)

Shen Guozhe; Hu Ping; Zhang Xiangkui; Chen Xiaobin; Li Xiaoda

2005-01-01

Springback is an unquenchable forming defect in the sheet metal forming process. How to calculate springback accurately is a big challenge for a lot of FEA software. Springback compensation makes the stamped final part accordant with the designed part shape by modifying tool surface, which depends on the accurate springback amount. How ever, the meshing data based on numerical simulation is expressed by nodes and elements, such data can not be supplied directly to tool surface CAD data. In this paper, a tool surface compensation algorithm based on numerical simulation technique of springback process is proposed in which the independently developed dynamic explicit springback algorithm (DESA) is used to simulate springback amount. When doing the tool surface compensation, the springback amount of the projected point can be obtained by interpolation of the springback amount of the projected element nodes. So the modified values of tool surface can be calculated reversely. After repeating the springback and compensation calculations for 1∼3 times, the reasonable tool surface mesh is gained. Finally, the FEM data on the compensated tool surface is fitted into the surface by CAD modeling software. The examination of a real industrial part shows the validity of the present method

An examination of compensation effects in accelerometer-measured occupational and non-occupational physical activity

Directory of Open Access Journals (Sweden)

Jennifer L. Gay

2017-12-01

Full Text Available Self-report data suggests a large proportion of total physical activity (PA occurs at work. However, adults with higher levels of occupational PA may compensate by engaging in less non-occupational PA. The study aims were to 1 estimate the intensity, volume, and duration of PA in American adults that occurs at work, and 2 determine if those more active at work are less active outside of work. A cross-sectional sample of full-time employed adults (N=510 was recruited from Georgia city and county governments in 2013–2015. Participants wore an Actigraph GT3X+ accelerometer for two weeks. In 2016, for 442 participants with complete data including work schedules and self-reported job titles, accelerometer wear minutes were classified as either occupational or non-occupational, and as sedentary, LPA (light-intensity PA, or MVPA (moderate-to-vigorous intensity PA. The proportion of daily PA that occurred during work was 41.2% for total PA, 41.0% for LPA, and 39.5% for MVPA. Higher levels of occupational LPA were associated with lower levels of non-occupational LPA (r=−0.38, P<0.0001. However, higher levels of occupational MVPA were associated with higher levels of non-occupational MVPA (r=0.17, P<0.0001. These associations remained significant in a MANOVA adjusting for labor sector and other covariates. On average, employed adults get more LPA and MVPA outside of work. Adults who do more occupational MVPA do not compensate by doing less non-occupational MVPA. In contrast, adults who do more occupational LPA do compensate by doing less non-occupational LPA. Evaluations of interventions to reduce sedentary behavior should be designed to detect compensation effects. Keywords: Intensity, Work, Accelerometer

Total body irradiation with an arc and a gravity-oriented compensator

International Nuclear Information System (INIS)

Chui, C.-S.; Fontenla, Doracy P.; Mullokandov, Edward; Kapulsky, Alex; Lo, Y.-C.; Lo, C.-J.

1997-01-01

Purpose: To deliver uniform dose distributions for total-body irradiation (TBI) with an arc field and a gravity-oriented compensator. This technique allows the patient to be treated lying on the floor in a small treatment room. Methods and Materials: Through the sweeping motion of the gantry, a continuous arc field can deliver a large field to a patient lying on the floor. The dose profile, however, would not be uniform if no compensator were used, due to the effects of inverse square variation of beam intensity with distance as well as the slanted depth in patient. To solve this problem, a gravity-oriented compensator made of cerrobend alloy was designed. This compensator has a cross-section of an inverted isosceles triangle, with the apex always pointing downward, due to gravity. By properly selecting the thickness of the compensator, the width of the base, and the distance between the pivots to the base, the difference in the path length through the compensator can be made just right to compensate the effects of inverse-square and slanted depth, thus producing a uniform dose profile. Results: Arc fields with a gravity-oriented compensator were used for 6, 10, 15, and 18 MV photon beams. The arc field can cover a patient with a height up to 180 cm. The field width was chosen from 32 to 40 cm at the machine isocenter. The optimal thickness of the compensator was found to be 2.5 cm, and its base was 25 cm wide. The distance from the pivot points to the flat surface of the compensator proximal to the beam ranges from 13 to 14 cm for different beam energies. The dose uniformity at a depth of 10 cm is within ±5% for all beam energies used in this study. Conclusion: Highly uniform dose profiles for TBI treatments can be delivered with an arc and a gravity-oriented compensator. The proposed technique is simple and versatile. A single compensator can be used for all energies, because the amount of compensation can be adjusted by changing the distance to the pivot and

The background factor of the driving compensation behavior among elderly drivers

OpenAIRE

Usui, Shinnosuke; Taishi, Nozomi

2016-01-01

The purpose of this study is to examine what factors lead to driving compensation behavior among elderly drivers, particularly focusing on the effect of self-reported driving performance, and to investigate the relationship between driving compensation behavior and traffic accidents or violations. After analyzing 237 elderly drivers, the results showed that whereas self-reported driving performances influenced driving compensation behaviors, the relationship between self-reported driving perf...

48 CFR 970.2270 - Unemployment compensation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to the...

38 CFR 3.351 - Special monthly dependency and indemnity compensation, death compensation, pension and spouse's...

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Special monthly dependency and indemnity compensation, death compensation, pension and spouse's compensation ratings. 3.351 Section 3.351 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension...

Complexities in understanding the role of compensation-related factors on recovery from whiplash-associated disorders : discussion paper 2

NARCIS (Netherlands)

Carroll, Linda J.; Connelly, Luke B.; Spearing, Natalie M.; Cote, Pierre; Buitenhuis, Jan; Kenardy, Justin

2011-01-01

Study Design. Focused discussion. Objective. To present some of the complexities in conducting research on the role of compensation and compensation-related factors in recovery from whiplash-associated disorders (WAD) and to suggest directions for future research. Summary of Background Data. There

Effects of chronic infusion of a GABAA receptor agonist or antagonist into the vestibular nuclear complex on vestibular compensation in the guinea pig.

Science.gov (United States)

Gliddon, Catherine M; Darlington, Cynthia L; Smith, Paul F

2005-06-01

The aim of this study was to determine the effects of chronic infusion of a GABA(A) receptor agonist/antagonist into the ipsilateral or contralateral vestibular nuclear complex (VNC) on vestibular compensation, the process of behavioral recovery that occurs after unilateral vestibular deafferentation (UVD). This was achieved by a mini-osmotic pump that infused, over 30 h, muscimol or gabazine into the ipsilateral or contralateral VNC. Spontaneous nystagmus (SN), yaw head tilt (YHT), and roll head tilt (RHT) were measured. Infusion of muscimol or gabazine into either the ipsilateral or the contralateral VNC had little effect on SN compensation. In contrast, infusion of muscimol (250, 500, and 750 ng) into the contralateral VNC and gabazine (31.25, 62.5, and 125 ng) into the ipsilateral VNC significantly affected YHT and RHT (p 0.05). Interestingly, the effects of muscimol and gabazine on YHT and RHT were consistent throughout the first 30 h post-UVD. Infusion of muscimol (62.5, 125, and 250 ng) into the ipsilateral VNC and gabazine (125, 375, and 750 ng) into the contralateral VNC had little effect on YHT and RHT or their rate of compensation. These results suggest that the ipsilateral gabazine and contralateral muscimol infusions are modifying the expression of the symptoms without altering the mechanism of compensation. Furthermore, the neurochemical mechanism responsible for vestibular compensation can cope with the both the GABA(A) receptor-mediated and the UVD-induced decrease in resting activity.

Remuneration Committee, Board Independence and Top Executive Compensation

Directory of Open Access Journals (Sweden)

Chii-Shyan Kuo

2014-04-01

Full Text Available In this study, we examine whether the levels and structures of top executive compensation vary discernibly with different levels of board independence. We also examine how the newly mandated adoption of the remuneration committee (RC in Taiwan affects the board independence-executive pay relation. The mandatory establishment of RC for Taiwanese public firms, starting in 2011, is intended to strengthen the reasonableness and effectiveness of the executive compensation structure; thus, it is timely and of interest for practitioners and regulators to understand whether the establishment of RCs can effectively discipline top executive compensation policies. We first find that CEOs of firms that do not appoint independent directors have greater levels of annual pay than is the case for firms that have appointed independent directors, after controlling for the effect of CEO pay determinants. Second, we find that CEO pay for early RC adopters is more closely related to firm performance. Third, we find that the establishing of RCs may decrease CEO pay and enhance the pay-performance association, in particular for firms that have not appointed independent directors; however, this effect is not found to be statistically significant.

29 CFR 525.6 - Compensable time.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those hours...

Motion-compensated processing of image signals

NARCIS (Netherlands)

2010-01-01

In a motion-compensated processing of images, input images are down-scaled (scl) to obtain down-scaled images, the down-scaled images are subjected to motion- compensated processing (ME UPC) to obtain motion-compensated images, the motion- compensated images are up-scaled (sc2) to obtain up-scaled

Compensation Consultants and CEO Pay

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Minhat, Marizah

2014-01-01

The study examines the practice of employing multiple compensation consultants. Examining data of a sample of UK companies over the period 2003–2006 we find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant. An increase in the number of compensation

Performance trade-offs in disturbance feedforward compensation of active hard-mounted vibration isolators

NARCIS (Netherlands)

Beijen, M.A.; Heertjes, M.F.; Butler, H.; Steinbuch, M.

2015-01-01

With disturbance feedforward compensation (DFC), input disturbances are measured and compensated to cancel the effect of the disturbance. Perfect cancellation is not possible in practice due to the causal nature of DFC, in which the compensation generally comes too late. Therefore, non-perfect plant

Radiological properties of a wax-gypsum compensator material

International Nuclear Information System (INIS)

Plessis, F.C.P. du; Willemse, C.A.

2005-01-01

In this paper the radiological properties of a compensator material consisting of wax and gypsum is presented. Effective attenuation coefficients (EACs) have been determined from transmission measurements with an ion chamber in a Perspex phantom. Measurements were made at 80 and 100 cm source-to-skin distance (SSD) for beam energies of 6, 8, and 15 MV, for field sizes ranging from narrow beam geometries up to 40x40 cm 2 , and at measurement depths of maximum dose build-up, 5 and 10 cm. A parametrization equation could be constructed to predict the EAC values within 4% uncertainty as a function of field size and depth of measurement. The EAC dependence on off-axis position was also quantified at each beam energy and SSD. It was found that the compensator material reduced the required thickness for compensation by 26% at 8 MV when compared to pure paraffin wax for a 10x10 cm 2 field. Relative surface ionization (RSI) measurements have been made to quantify the effect of scattered electrons from the wax-gypsum compensator. Results indicated that for 80 cm SSD the RSI would exceed 50% for fields larger than 15x15 cm 2 . At 100 cm SSD the RSI values were below 50% for all field sizes used

Optimal coordination of distance and over-current relays in series compensated systems based on MAPSO

International Nuclear Information System (INIS)

Moravej, Zahra; Jazaeri, Mostafa; Gholamzadeh, Mehdi

2012-01-01

Highlight: ► Optimal coordination problem between distance relays and Directional Over-Current Relays (DOCRs) is studied. ► A new problem formulation for both uncompensated and series compensated system is proposed. ► In order to solve the coordination problem a Modified Adaptive Particle Swarm Optimization (MAPSO) is employed. ► The optimum results are found in both uncompensated and series compensated systems. - Abstract: In this paper, a novel problem formulation for optimal coordination between distance relays and Directional Over-Current Relays (DOCRs) in series compensated systems is proposed. The integration of the series capacitor (SC) into the transmission line makes the coordination problem more complex. The main contribution of this paper is a new systematic method for computing the optimal second zone timing of distance relays and optimal settings of DOCRs, in series compensated and uncompensated transmission systems, which have a combined protection scheme with DOCRs and distance relays. In order to solve this coordination problem, which is a nonlinear and non-convex problem, a Modified Adaptive Particle Swarm Optimization (MAPSO) is employed. The new proposed method is supported by obtained results from a typical test case and a real power system network.

Thermal-Induced Errors Prediction and Compensation for a Coordinate Boring Machine Based on Time Series Analysis

Directory of Open Access Journals (Sweden)

Jun Yang

2014-01-01

Full Text Available To improve the CNC machine tools precision, a thermal error modeling for the motorized spindle was proposed based on time series analysis, considering the length of cutting tools and thermal declined angles, and the real-time error compensation was implemented. A five-point method was applied to measure radial thermal declinations and axial expansion of the spindle with eddy current sensors, solving the problem that the three-point measurement cannot obtain the radial thermal angle errors. Then the stationarity of the thermal error sequences was determined by the Augmented Dickey-Fuller Test Algorithm, and the autocorrelation/partial autocorrelation function was applied to identify the model pattern. By combining both Yule-Walker equations and information criteria, the order and parameters of the models were solved effectively, which improved the prediction accuracy and generalization ability. The results indicated that the prediction accuracy of the time series model could reach up to 90%. In addition, the axial maximum error decreased from 39.6 μm to 7 μm after error compensation, and the machining accuracy was improved by 89.7%. Moreover, the X/Y-direction accuracy can reach up to 77.4% and 86%, respectively, which demonstrated that the proposed methods of measurement, modeling, and compensation were effective.

Motion Estimation and Compensation Strategies in Dynamic Computerized Tomography

Science.gov (United States)

Hahn, Bernadette N.

2017-12-01

A main challenge in computerized tomography consists in imaging moving objects. Temporal changes during the measuring process lead to inconsistent data sets, and applying standard reconstruction techniques causes motion artefacts which can severely impose a reliable diagnostics. Therefore, novel reconstruction techniques are required which compensate for the dynamic behavior. This article builds on recent results from a microlocal analysis of the dynamic setting, which enable us to formulate efficient analytic motion compensation algorithms for contour extraction. Since these methods require information about the dynamic behavior, we further introduce a motion estimation approach which determines parameters of affine and certain non-affine deformations directly from measured motion-corrupted Radon-data. Our methods are illustrated with numerical examples for both types of motion.

The Nature of Whiplash in a Compensable Environment: Injury, Disability, Rehabilitation, and Compensation Systems.

Science.gov (United States)

Connelly, Luke B

2017-07-01

Synopsis Whiplash is a compensable injury in many jurisdictions, but there is considerable heterogeneity in the compensation arrangements that apply across jurisdictions, even within some countries. These compensation schemes have, however, been subject to a common set of interrelated concerns, chiefly concerning the incentives, behaviors, and outcomes that may arise when financial compensation for injuries is available to injured parties. This article provides a nontechnical overview of some of those concerns through the lens of economics: principally, insurance economics and health economics, including related subsets such as information economics and agency theory, as well as economics and the law. It notes that because it is generally infeasible to randomize the treatment (ie, compensation) via trials, analyses of observational data are necessary to discover more about the relationship between compensation and health outcomes. This poses the analytical challenge of discovering causal connections between phenomena from nonrandomized data sets. The present article calls for further research that would enable convincing causal interpretations of such relationships via the careful analysis of rich observational data sets using modern econometric methods. J Orthop Sports Phys Ther 2017;47(7):503-508. Epub 16 Jun 2017. doi:10.2519/jospt.2017.7533.

A primer for workers' compensation.

Science.gov (United States)

Bible, Jesse E; Spengler, Dan M; Mir, Hassan R

2014-07-01

A physician's role within a workers' compensation injury extends far beyond just evaluation and treatment with several socioeconomic and psychological factors at play compared with similar injuries occurring outside of the workplace. Although workers' compensation statutes vary among states, all have several basic features with the overall goal of returning the injured worker to maximal function in the shortest time period, with the least residual disability and shortest time away from work. To help physicians unfamiliar with the workers' compensation process accomplish these goals. Review. Educational review. The streamlined review addresses the topics of why is workers' compensation necessary; what does workers' compensation cover; progression after work injury; impairment and maximum medical improvement, including how to use the sixth edition of American Medical Association's (AMA) Guides to the evaluation of permanent impairment (Guides); completion of work injury claim after impairment rating; independent medical evaluation; and causation. In the "no-fault" workers' compensation system, physicians play a key role in progressing the claim along and, more importantly, getting the injured worker back to work as soon as safely possible. Physicians should remain familiar with the workers' compensation process, along with how to properly use the AMA Guides. Copyright © 2014 Elsevier Inc. All rights reserved.

A new method for compensation of the effect of charging transformer's leakage inductance on PFN voltage regulation in Klystron pulse modulators

Energy Technology Data Exchange (ETDEWEB)

Patel, Akhil, E-mail: akhilpatel@rrcat.gov.in; Kale, Umesh; Shrivastava, Purushottam

2017-04-21

The Line type modulators have been widely used to generate high voltage rectangular pulses to power the klystron for high power RF generation. In Line type modulator, the Pulse Forming Network (PFN) which is a cascade combination of lumped capacitors and inductors is used to store the electrical energy. The charged PFN is then discharged into a klystron by firing a high voltage Thyratron switch. This discharge generates a high voltage rectangular pulse across the klystron electrodes. The amplitude and phase of Klystron's RF output is governed by the high voltage pulse amplitude. The undesired RF amplitude and phase stability issues arises at the klystron's output due to inter-pulse and during the pulse amplitude variations. To reduce inter-pulse voltage variations, the PFN is required to be charged at the same voltage after every discharge cycle. At present, the combination of widely used resonant charging and deQing method is used to regulate the pulse to pulse PFN voltage variations but the charging transformer's leakage inductance puts an upper bound on the regulation achievable by this method. Here we have developed few insights of the deQing process and devised a new compensation method to compensate this undesired effect of charging transformer's leakage inductance on the pulse to pulse PFN voltage stability. This compensation is accomplished by the controlled partial discharging of the split PFN capacitor using a low voltage MOSFET switch. Theoretically, very high values of pulse to pulse voltage stability may be achieved using this method. This method may be used in deQing based existing modulators or in new modulators, to increase the pulse to pulse voltage stability, without having a very tight bound on charging transformer's leakage inductance. Given a stable charging power supply, this method may be used to further enhance the inter-pulse voltage stability of modulators which employ the direct charging, after replacing the

The Potential Effects of Federal Health Insurance Reforms on Employment Arrangements and Compensation

OpenAIRE

Marcus Dillender; Carolyn J. Heinrich; Susan N. Houseman

2015-01-01

The Affordable Care Act (ACA) presents an opportunity to significantly improve compensation for American workers. A potential concern, though, is that employers will circumvent the employer mandate by increasing their use of workers in staffing arrangements that are not covered by the mandate: workers averaging less than 30 hours per week, working on a temporary basis, or working in organizations with fewer than 50 full-time employees. In this paper, we shed light on the likely effects that t...

Compensation of PVT Variations in ToF Imagers with In-Pixel TDC.

Science.gov (United States)

Vornicu, Ion; Carmona-Galán, Ricardo; Rodríguez-Vázquez, Ángel

2017-05-09

The design of a direct time-of-flight complementary metal-oxide-semiconductor (CMOS) image sensor (dToF-CIS) based on a single-photon avalanche-diode (SPAD) array with an in-pixel time-to-digital converter (TDC) must contemplate system-level aspects that affect its overall performance. This paper provides a detailed analysis of the impact of process parameters, voltage supply, and temperature (PVT) variations on the time bin of the TDC array. Moreover, the design and characterization of a global compensation loop is presented. It is based on a phase locked loop (PLL) that is integrated on-chip. The main building block of the PLL is a voltage-controlled ring-oscillator (VCRO) that is identical to the ones employed for the in-pixel TDCs. The reference voltage that drives the master VCRO is distributed to the voltage control inputs of the slave VCROs such that their multiphase outputs become invariant to PVT changes. These outputs act as time interpolators for the TDCs. Therefore the compensation scheme prevents the time bin of the TDCs from drifting over time due to the aforementioned factors. Moreover, the same scheme is used to program different time resolutions of the direct time-of-flight (ToF) imager aimed at 3D ranging or depth map imaging. Experimental results that validate the analysis are provided as well. The compensation loop proves to be remarkably effective. The spreading of the TDCs time bin is lowered from: (i) 20% down to 2.4% while the temperature ranges from 0 °C to 100 °C; (ii) 27% down to 0.27%, when the voltage supply changes within ±10% of the nominal value; (iii) 5.2 ps to 2 ps standard deviation over 30 sample chips, due to process parameters' variation.

Direction of travel can influence canine gait characteristics

DEFF Research Database (Denmark)

Miles, James Edward; Vitger, Anne Désiré; Poulsen, Helle Harding

Objectives To describe the effect of direction of travel on measurements of peak vertical force (PVF) and vertical impulse (VI) obtained using a Tekscan walkway system. Methods Following acclimatisation, recordings were obtained for six healthy dogs walking twice in in each direction along the wa...... between measurements at different times, and to compensate for the effect of direction of travel on outcome measures.......Objectives To describe the effect of direction of travel on measurements of peak vertical force (PVF) and vertical impulse (VI) obtained using a Tekscan walkway system. Methods Following acclimatisation, recordings were obtained for six healthy dogs walking twice in in each direction along...... the walkway. PVF and VI measurements were normalised and used to calculate left:right symmetry ratios for forelimb and hindlimb loading in each travel direction and for all recordings. Results Mean walking speed was 1.2 ± 0.14 m/s. Mean body mass was 25 ± 5 kg. No gross evidence of pulling to left or right...

A novel technique for compensation of space charge effects in the LUPIN-II detector

Energy Technology Data Exchange (ETDEWEB)

Cassell, C., E-mail: cc878@uowmail.edu.au [Politecnico of Milan, Department of Energy, Via la Masa 34, 20154 Milan (Italy); University of Wollongong, Centre for Medical Physics, NSW 2522 (Australia); Ferrarini, M. [Fondazione CNAO, via Caminadella16, 20123 Milano (Italy); Rosenfeld, A. [University of Wollongong, Centre for Medical Physics, NSW 2522 (Australia); Caresana, M. [Politecnico of Milan, Department of Energy, Via la Masa 34, 20154 Milan (Italy)

2015-12-21

A new method for improving REM counter performance in Pulsed Neutron Fields (PNFs) has been developed. This method uses an analysis of the build-up of space charge in the counter to compensate for an underestimation of Ambient Dose Equivalent (H*(10)) in intense pulsed fields. It was applied to three sets of experimental data acquired using the LUPIN-II REM counter device, which is designed for use in PNFs. The data was acquired using the cyclotron at Helmholtz-Zentrum Berlin für Materialien und Energie GmbH (HZB), at the HiRadMat facility at CERN and at the ‘Elettra Sincrotrone Trieste’ (ELETTRA), Italy. A comparison of the data with and without this compensation method is used to highlight its effectiveness. The LUPIN-II performance, which has already been shown to be able to cope with fields of up to hundreds of nSv/burst, is improved by at least one order of magnitude, with further potential for improvement.

42 CFR 413.102 - Compensation of owners.

Science.gov (United States)

2010-10-01

...) Definitions—(1) Compensation. Compensation means the total benefit received by the owner for the services he... 42 Public Health 2 2010-10-01 2010-10-01 false Compensation of owners. 413.102 Section 413.102... § 413.102 Compensation of owners. (a) Principle. A reasonable allowance of compensation for services of...

Skew quad compensation for SPEAR minibeta optics

International Nuclear Information System (INIS)

Wille, K.

1984-06-01

With the new minibeta insertion for SPEAR the betatron coupling and the perturbations of beam optics caused by the solenoid field of the MARK III detector can't be compensated by the simple coils used so far. Therefore another scheme with four skew quads arranged in two families has been chosen. Even though this scheme doesn't compensate the effect of the solenoid on the beam completely, the residual emittance coupling is much less than 1% which should be sufficient under all running conditions. The major advantage of this concept is its simplicity

Harmonic currents Compensator Grid-Connected Inverter at the Microgrid

DEFF Research Database (Denmark)

Asuhaimi Mohd Zin, A.; Naderipour, A.; Habibuddin, M.H.

2016-01-01

The main challenge associated with the grid-connected inverter in distributed generation (DG) systems is to maintain the harmonic contents in output current below the specified values and compensates for unbalanced loads even when the grid is subject to disturbances such as harmonic distortion...... and unbalanced loads. To overcome these challenges, a current control strategy for a three-phase grid-connected inverter under unbalanced and nonlinear load conditions is presented. It enables grid-connected inverter by the proposed control method to inject balanced clean currents to the grid even when the local...... loads are unbalanced and/or nonlinear and also compensate of the harmonic currents and control the active and reactive power. The main advantage and objective of this method is to effectively compensate for the harmonic currents content of the grid current and microgrid without using any compensation...

Analysis and compensation for the joint effects of HPA nonlinearity, I/Q imbalance and crosstalk in MIMO beamforming systems

KAUST Repository

Qi, Jian

2011-03-01

In this paper, we investigate the joint effects of high-power amplifier (HPA) nonlinearity, in-phase/quadrature-phase (I/Q) imbalance and crosstalk, on the performance of multiple-input multiple-output (MIMO) transmit beamforming (TB) systems, and propose a compensation method for the three impairments together. The performance of the MIMO TB system equipped with the proposed compensation scheme is evaluated in terms of average symbol error probability and capacity when transmissions are performed over uncorrelated Rayleigh fading channels. Numerical results are provided and show the effects on performance of several system parameters, namely, the HPA parameters, image-leakage ratio, crosstalk, numbers of antennas, length of pilot symbols and phase-shift keying modulation order. © 2011 IEEE.

Robust finite-time tracking control for nonlinear suspension systems via disturbance compensation

Science.gov (United States)

Pan, Huihui; Jing, Xingjian; Sun, Weichao

2017-05-01

This paper focuses on the finite-time tracking control with external disturbance for active suspension systems. In order to compensate unknown disturbance efficiently, a disturbance compensator with finite-time convergence property is studied. By analyzing the discontinuous phenomenon of classical disturbance compensation techniques, this study presents a simple approach to construct a continuous compensator satisfying the finite-time disturbance rejection performance. According to the finite-time separation principle, the design procedures of the nominal controller for the suspension system without disturbance and the disturbance compensator can be implemented in a completely independent manner. Therefore, the overall control law for the closed-loop system is continuous, which offers some distinct advantages over the existing discontinuous ones. From the perspective of practical implementation, the continuous controller can avoid effectively the unexpected chattering in active suspension control. Comparative experimental results are presented and discussed to illustrate the advantage and effectiveness of the proposed control strategy.

Deformation compensation in dynamic tomography; Compensation de deformations en tomographie dynamique

Energy Technology Data Exchange (ETDEWEB)

Desbat, L. [Universite Joseph Fourier, UMR CNRS 5525, 38 - Grenoble (France); Roux, S. [Universite Joseph Fourier, TIMC-IMAG, In3S, Faculte de Medecine, 38 - Grenoble (France)]|[CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France); Grangeat, P. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France)

2005-07-01

This work is a contribution to the compensation of motion in tomography. New classes of deformation are proposed, that compensates analytically by an algorithm of a F.B.P. type reconstruction. This work makes a generalisation of the known results for affine deformations, in parallel geometry and fan-beam, to deformation classes of infinite dimension able to include strong non linearities. (N.C.)

Hybrid VAR compensator with improved efficiency

Directory of Open Access Journals (Sweden)

V. V. Burlaka

2015-03-01

Full Text Available In modern electrical networks thyristor-switched capacitors (TSC are most used devices for VAR compensation. These devices don’t contain rotating parts and mechanical contacts, provide a stepwise control of reactive power and no generation of harmonics to the network. However, with the help of TSC it’s not possible to ensure smooth control of reactive power and capacitor banks (CB are exposed to the negative impact of higher harmonic components of the network voltage. Hybrid VAR compensator don’t have such drawbacks. It consists of active filter (AF and capacitor bank with discrete regulation. The main drawback of such systems is the necessity of accessing all six terminals of CB, while most of them are manufactured with three terminals, internally delta-connected. In the article, the topology and control system of hybrid VAR compensator free from beforementioned drawback, is proposed. The control system provides operating modes of overcompensation or undercompensation reactive power. VAR distribution regulator performs redistribution of reactive power between active filter and capacitor banks with the condition to minimize active filter’s power. Scheme of the hybrid VAR compensator, which includes a three-phase three-terminal delta-connected capacitor banks, is shown. Proposed approach allows to provide smooth control of reactive power, isolate the capacitor bank from harmonic currents and use a more effective low-voltage power components

Effect in Protecting Cultivated Land of New Construction Land Compensation Fee%新增建设用地使用费的耕地保护绩效测算

Institute of Scientific and Technical Information of China (English)

丁宁; 金晓斌; 唐健; 张志宏; 赵婕; 宋佳楠; 周寅康

2011-01-01

论文以农用地转用环节征收数额较大、改革相对较早的新增建设用地土地有偿使用费为研究对象,应用2003—2008年省级面板数据,建立土地有偿使用费征收率与建设占用耕地面积间动态变化的计量经济函数,采用混合OLS模型加以估计,并在此基础上对土地有偿使用费政策的耕地保护绩效进行测算。研究结果表明：①2003—2008年间,土地有偿使用费征收率每提高1元/m2,每省每年约能减少耕地占用面积47.26 hm2;②2003—2008年土地有偿使用费政策实施累计抑制建设占用耕地面积152 410.00 hm2,其耕地保护%Land taxes and fees have played an important role in protecting farmland and improving the efficiency of land use.This paper studies new construction land compensation fee,which is charged in comparatively large amounts and has experienced a long term of reform.Its effects in cultivated land protection can make a good reference to the improvement and perfection of the land taxes and fees system.The province-level panel data from 2003 to 2008 was used in the research to establish the econometric model that describes the dynamic changes between the charging rate of new construction compensation fee and cultivated land occupation area by construction.The mixed OLS model was applied to estimate the equations and the cultivated land preservation effect of new construction compensation fee was assessed by computing estimated decreased areas of cultivated land occupation with and without new construction land compensation fee policy in effect.The estimated results of model shows that the variables’ sign symbols were consistent with expected and the t test was significant at 10% level.The model can be used to calculate the direct effects and relative effects of new construction land compensation fee on cultivated land preservation.The main conclusions of the research are： 1） The cultivated land occupation reduced by about 47.26 hm2 with

Asbestos-related occupational cancers compensated under the Industrial Accident Compensation Insurance in Korea.

Science.gov (United States)

Ahn, Yeon-Soon; Kang, Seong-Kyu

2009-04-01

Compensation for asbestos-related cancers occurring in occupationally-exposed workers is a global issue; this is also an issue in Korea. To provide basic information regarding compensation for workers exposed to asbestos, 60 cases of asbestos-related occupational lung cancer and mesothelioma that were compensated during 15 yr; from 1993 (the year the first case was compensated) to 2007 by the Korea Labor Welfare Corporation (KLWC) are described. The characteristics of the cases were analyzed using the KLWC electronic data and the epidemiologic investigation data conducted by the Occupational Safety and Health Research Institute (OSHRI) of the Korea Occupational Safety and Health Agency (KOSHA). The KLWC approved compensation for 41 cases of lung cancer and 19 cases of mesothelioma. Males accounted for 91.7% (55 cases) of the approved cases. The most common age group was 50-59 yr (45.0%). The mean duration of asbestos exposure for lung cancer and mesothelioma cases was 19.2 and 16.0 yr, respectively. The mean latency period for lung cancer and mesothelioma cases was 22.1 and 22.6 yr, respectively. The major industries associated with mesothelioma cases were shipbuilding and maintenance (4 cases) and manufacture of asbestos textiles (3 cases). The major industries associated with lung cancer cases were shipbuilding and maintenance (7 cases), construction (6 cases), and manufacture of basic metals (4 cases). The statistics pertaining to asbestos-related occupational cancers in Korea differ from other developed countries in that more cases of mesothelioma were compensated than lung cancer cases. Also, the mean latency period for disease onset was shorter than reported by existing epidemiologic studies; this discrepancy may be related to the short history of occupational asbestos use in Korea. Considering the current Korean use of asbestos, the number of compensated cases in Korea is expected to increase in the future but not as much as developed countries.

Carbon Dioxide Compensation Values in Citronella and Lemongrass 1

Science.gov (United States)

Herath, H. M. Walter; Ormrod, Douglas P.

1977-01-01

Carbon dioxide compensation values of mature leaves from 10 selections of citronella (Cymbopogon nardus [L.] Rendle) grown at 32/27 or 27/21 C day/night temperatures and three strains of lemongrass (Cymbopogon citratus [D.C.] Stapf. and Cymbopogon flexuosus [D.C.] Stapf.) grown at 8- or 15-hour photoperiods were measured in a controlled environment at 25 C. All leaves had low compensation values but citronella varied from 1.3 to 9.7 μl/liter and lemongrass from 0.7 to 3.5 μl/liter. Lower growing temperature generally resulted in lower compensation values for citronella but there was no consistent photoperiod effect on lemongrass. PMID:16659935

Study of SPM tolerances of electronically compensated DML based systems.

Science.gov (United States)

Papagiannakis, I; Klonidis, D; Birbas, Alexios N; Kikidis, J; Tomkos, I

2009-05-25

This paper experimentally investigates the effectiveness of electronic dispersion compensation (EDC) for signals limited by self phase modulation (SPM) and various dispersion levels. The sources considered are low-cost conventional directly modulated lasers (DMLs), fabricated for operation at 2.5 Gb/s but modulated at 10 Gb/s. Performance improvement is achieved by means of electronic feed-forward and decision-feedback equalization (FFE/DFE) at the receiver end. Experimental studies consider both transient and adiabatic chirp dominated DMLs sources. The improvement is evaluated in terms of required optical signal-to-noise ratio (ROSNR) for bit-error-rate (BER) values of 10(-3) versus launch power over uncompensated links of standard single mode fiber (SSMF).

Die Face Engineering based Springback Compensation Strategy and Implementation

International Nuclear Information System (INIS)

Tang, Arthur; Lee Wing; He, Jeanne; Xu Jinbo; Liu Kesu; Chen Chinchun

2005-01-01

Springback or shape change has been one of the major challenges in sheet metal fabrication, particularly with increase application of high strength steel (HSS) and aluminum alloys in automotive stamping. Springback, an elastic material recovery after the unloading of stamping tools, causes variations and inconsistencies of final part dimensions. Minor or mild springback usually can be corrected in the re-strike process. Excessive springback must be corrected so the part will be produced within the given design tolerance and dimension. The commonly used Spring Forward approaches and shape compensations such as over-crown and over-bending are proven effective to alleviate excessive springback. To enhance these approaches, a new strategy of Die Face Engineering (DFE) based processing is proposed to quickly and easily to achieve the maximum allowable compensation using the under cut (or die lock) as the primary criteria. The implementation of the die face compensation through iterative FEA calculation, automatic surface mapping, projection and manual morphing are crucial to meet production environment requirements in terms of generating NC quality CAD surfaces of the compensated or morphed die face. In this paper, the strategy of the die face compensation with the consideration of the under cut criteria is presented. The implementation of various processes to enable user to perform the die face compensation task in a production environment is also discussed. Finally, two examples are shown to demonstrate the implementation of the proposed springback compensation scheme based on the combined CAE/CAD methodology

Fuzzy Control of Cold Storage Refrigeration System with Dynamic Coupling Compensation

Directory of Open Access Journals (Sweden)

Xiliang Ma

2018-01-01

Full Text Available Cold storage refrigeration systems possess the characteristics of multiple input and output and strong coupling, which brings challenges to the optimize control. To reduce the adverse effects of the coupling and improve the overall control performance of cold storage refrigeration systems, a control strategy with dynamic coupling compensation was studied. First, dynamic model of a cold storage refrigeration system was established based on the requirements of the control system. At the same time, the coupling between the components was studied. Second, to reduce the adverse effects of the coupling, a fuzzy controller with dynamic coupling compensation was designed. As for the fuzzy controller, a self-tuning fuzzy controller was served as the primary controller, and an adaptive neural network was adopted to compensate the dynamic coupling. Finally, the proposed control strategy was employed to the cold storage refrigeration system, and simulations were carried out in the condition of start-up, variable load, and variable degree of superheat, respectively. The simulation results verify the effectiveness of the fuzzy control method with dynamic coupling compensation.

Illumination robust face recognition using spatial adaptive shadow compensation based on face intensity prior

Science.gov (United States)

Hsieh, Cheng-Ta; Huang, Kae-Horng; Lee, Chang-Hsing; Han, Chin-Chuan; Fan, Kuo-Chin

2017-12-01

Robust face recognition under illumination variations is an important and challenging task in a face recognition system, particularly for face recognition in the wild. In this paper, a face image preprocessing approach, called spatial adaptive shadow compensation (SASC), is proposed to eliminate shadows in the face image due to different lighting directions. First, spatial adaptive histogram equalization (SAHE), which uses face intensity prior model, is proposed to enhance the contrast of each local face region without generating visible noises in smooth face areas. Adaptive shadow compensation (ASC), which performs shadow compensation in each local image block, is then used to produce a wellcompensated face image appropriate for face feature extraction and recognition. Finally, null-space linear discriminant analysis (NLDA) is employed to extract discriminant features from SASC compensated images. Experiments performed on the Yale B, Yale B extended, and CMU PIE face databases have shown that the proposed SASC always yields the best face recognition accuracy. That is, SASC is more robust to face recognition under illumination variations than other shadow compensation approaches.

New York State's landmark policies on oversight and compensation for egg donation to stem cell research.

Science.gov (United States)

Roxland, Beth E

2012-05-01

In 2009, New York became the first US state to implement a policy permitting researchers to use public funds to reimburse women who donate oocytes directly and solely to stem cell research, not only for the woman's out-of-pocket expenses, but also for the time, burden and discomfort associated with the donation process. The debate about the propriety of such compensation was recently renewed with the publication of a stem cell study in which women were provided with compensation for donating their eggs. This article explores the scientific and ethical rationales that led to New York's decision to allow donor compensation. The multifaceted deliberation process and comprehensive policies may serve as a model for other states and countries considering the issue of oocyte donor compensation.

Ecological compensation: From general guidance and expertise to specific proposals for road developments

International Nuclear Information System (INIS)

Villarroya, Ana; Persson, Jesper; Puig, Jordi

2014-01-01

The main scientific bibliography addressing the rationale behind ecological compensation is reviewed in order to examine general guidelines. This contains interesting general guidance on how to implement compensation, and provides the basis for future developments in compensation practice. On this basis, we propose a further step in compensation practice, advancing compensation proposals or rules for specific kinds of projects and contexts, focusing on road projects in the Spanish Environmental Impact Assessment (EIA). Three main residual impacts of roads are identified which usually remain uncompensated for: the loss of natural and semi-natural land use, the increase in emissions resulting from any new road, and the fragmentation, severance or barrier effect on the landscape and its wildlife. To counteract these, four proposals, or “rules”, are advanced: conservation of natural and semi-natural land use area, conservation of dominant plant species physiognomy, compensation for emissions, and the rule of positive defragmentation. -- Highlights: • Ecological compensation theory does not specify guidelines for types of projects. • EIA practitioners lack valuable specific guidance on how to implement compensation. • Specific guidance for road project ecological compensation is proposed. • Compensation proposals should have in mind present-day compensation practice level. • Specific ways to compensate for habitat loss, emissions, and fragmentation are shown

Ecological compensation: From general guidance and expertise to specific proposals for road developments

Energy Technology Data Exchange (ETDEWEB)

Villarroya, Ana, E-mail: avillarroya@alumni.unav.es [Department of Zoology and Ecology, University of Navarra, c/Irunlarrea s/n, 31008 Pamplona, Navarra (Spain); Persson, Jesper, E-mail: jesper.persson@slu.se [Department of Landscape Management, Design and Construction, Swedish University of Agricultural Sciences (SLU), P.O. Box 66, SE-230 53 Alnarp (Sweden); Puig, Jordi, E-mail: jpbaguer@unav.es [Department of Zoology and Ecology, University of Navarra, c/Irunlarrea s/n, 31008 Pamplona, Navarra (Spain)

2014-02-15

The main scientific bibliography addressing the rationale behind ecological compensation is reviewed in order to examine general guidelines. This contains interesting general guidance on how to implement compensation, and provides the basis for future developments in compensation practice. On this basis, we propose a further step in compensation practice, advancing compensation proposals or rules for specific kinds of projects and contexts, focusing on road projects in the Spanish Environmental Impact Assessment (EIA). Three main residual impacts of roads are identified which usually remain uncompensated for: the loss of natural and semi-natural land use, the increase in emissions resulting from any new road, and the fragmentation, severance or barrier effect on the landscape and its wildlife. To counteract these, four proposals, or “rules”, are advanced: conservation of natural and semi-natural land use area, conservation of dominant plant species physiognomy, compensation for emissions, and the rule of positive defragmentation. -- Highlights: • Ecological compensation theory does not specify guidelines for types of projects. • EIA practitioners lack valuable specific guidance on how to implement compensation. • Specific guidance for road project ecological compensation is proposed. • Compensation proposals should have in mind present-day compensation practice level. • Specific ways to compensate for habitat loss, emissions, and fragmentation are shown.

Is clinician refusal to treat an emerging problem in injury compensation systems?

Science.gov (United States)

Brijnath, Bianca; Mazza, Danielle; Kosny, Agnieszka; Bunzli, Samantha; Singh, Nabita; Ruseckaite, Rasa; Collie, Alex

2016-01-01

Objective The reasons that doctors may refuse or be reluctant to treat have not been widely explored in the medical literature. To understand the ethical implications of reluctance to treat there is a need to recognise the constraints of doctors working in complex systems and to consider how these constraints may influence reluctance. The aim of this paper is to illustrate these constraints using the case of compensable injury in the Australian context. Design Between September and December 2012, a qualitative investigation involving face-to-face semistructured interviews examined the knowledge, attitudes and practices of general practitioners (GPs) facilitating return to work in people with compensable injuries. Setting Compensable injury management in general practice in Melbourne, Australia. Participants 25 GPs who were treating, or had treated a patient with compensable injury. Results The practice of clinicians refusing treatment was described by all participants. While most GPs reported refusal to treat among their colleagues in primary and specialist care, many participants also described their own reluctance to treat people with compensable injuries. Reasons offered included time and financial burdens, in addition to the clinical complexities involved in compensable injury management. Conclusions In the case of compensable injury management, reluctance and refusal to treat is likely to have a domino effect by increasing the time and financial burden of clinically complex patients on the remaining clinicians. This may present a significant challenge to an effective, sustainable compensation system. Urgent research is needed to understand the extent and implications of reluctance and refusal to treat and to identify strategies to engage clinicians in treating people with compensable injuries. PMID:26792215

Cooperation, compensation and transition

NARCIS (Netherlands)

Ju, Y.

2004-01-01

Cooperation and compensation are two important and well-linked issues in economics. The central question in cooperation is how to share the joint gains among participating players. Compensation is a specific aspect of surplus sharing problems providing incentives for agents to sacrifice their own

How to avoid deferred-compensation troubles.

Science.gov (United States)

Freeman, Todd I

2005-06-01

Executive compensation packages have long included stock options and deferred compensation plans in order to compete for talent. Last year, Congress passed a law in response to the Enron debacle, in which executives were perceived to be protecting their deferred compensation at the expense of employees, creditors, and investors. The new law is designed to protect companies and their shareholders from being raided by the very executives that guided the company to financial ruin. Physicians who are part owners of medical practices need to know about the changes in the law regarding deferred compensation and how to avoid costly tax penalties. This article discusses how the changes affect medical practices as well as steps physician-owned clinics can take to avoid the risk of penalty, such as freezing deferred compensation and creating a new deferred compensation plan.

Downplaying Positive Impressions: Compensation Between Warmth and Competence in Impression Management.

Science.gov (United States)

Holoien, Deborah Son; Fiske, Susan T

2013-01-01

The compensation effect demonstrates a negative relationship between the dimensions of warmth and competence in impression formation in comparative contexts. However, does compensation between warmth and competence extend to impression management? Two studies examined whether people actively downplay their warmth in order to appear competent and downplay their competence in order to appear warm. In Studies 1a and 1b, participants selected words pretested to be high or low in warmth and competence to include in an e-mail message to people they wanted to impress. As predicted, participants downplayed their competence when they wanted to appear warm (Study 1a) and downplayed their warmth when they wanted to appear competent (Study 1b). In Studies 2a and 2b, compensation also occurred when participants introduced themselves to another person, as evidenced by the questions they selected to answer about themselves, their self-reported goals, and their open-ended introductions. Compensation occurred uniquely between warmth and competence and not for other dimensions, such as healthiness (Study 2a) and political interest (Study 2b), which suggests that the compensation effect extends beyond a mere zero-sum exchange between dimensions.

A Smart High Accuracy Silicon Piezoresistive Pressure Sensor Temperature Compensation System

Directory of Open Access Journals (Sweden)

Guanwu Zhou

2014-07-01

Full Text Available Theoretical analysis in this paper indicates that the accuracy of a silicon piezoresistive pressure sensor is mainly affected by thermal drift, and varies nonlinearly with the temperature. Here, a smart temperature compensation system to reduce its effect on accuracy is proposed. Firstly, an effective conditioning circuit for signal processing and data acquisition is designed. The hardware to implement the system is fabricated. Then, a program is developed on LabVIEW which incorporates an extreme learning machine (ELM as the calibration algorithm for the pressure drift. The implementation of the algorithm was ported to a micro-control unit (MCU after calibration in the computer. Practical pressure measurement experiments are carried out to verify the system’s performance. The temperature compensation is solved in the interval from −40 to 85 °C. The compensated sensor is aimed at providing pressure measurement in oil-gas pipelines. Compared with other algorithms, ELM acquires higher accuracy and is more suitable for batch compensation because of its higher generalization and faster learning speed. The accuracy, linearity, zero temperature coefficient and sensitivity temperature coefficient of the tested sensor are 2.57% FS, 2.49% FS, 8.1 × 10−5/°C and 29.5 × 10−5/°C before compensation, and are improved to 0.13%FS, 0.15%FS, 1.17 × 10−5/°C and 2.1 × 10−5/°C respectively, after compensation. The experimental results demonstrate that the proposed system is valid for the temperature compensation and high accuracy requirement of the sensor.

Mutual compensation of wakefield and chromatic effects of intense linac bunches

International Nuclear Information System (INIS)

Seeman, J.T.; Merminga, N.

1990-05-01

Mutual compensation of transverse and chromatic effects for intense electron bunches in a high-energy linac is a recent Novosibirsk idea which provides a new control of emittance enlargement. In this paper we elaborate on the principles and constraints for this new technique which requires careful matching of internal bunch parameters with external forces. With species values of the bunch length, bunch intensity, and klystron phasing, the transverse-wakefield-induced forces within the bunch can be cancelled by energy-dependent forces from the quadrupole lattice at all positions along the linac. Under these conditions the tolerances for quadrupole alignment, dipole stability, and injection launch errors are significantly relaxed. 7 refs., 8 figs

Examining the Gap: Compensation Disparities between Male and Female Physician Assistants.

Science.gov (United States)

Smith, Noël; Cawley, James F; McCall, Timothy C

Compensation disparities between men and women have been problematic for decades, and there is considerable evidence that the gap cannot be entirely explained by nongender factors. The current study examined the compensation gap in the physician assistant (PA) profession. Compensation data from 2014 was collected by the American Academy of PAs in 2015. Practice variables, including experience, specialty, and hours worked, were controlled for in an ordinary least-squares sequential regression model to examine whether there remained a disparity in total compensation. In addition, the absolute disparity in compensation was compared with historical data collected by American Academy of PAs over the previous 1.5 decades. Without controlling for practice variables, a total compensation disparity of $16,052 existed between men and women in the PA profession. Even after PA practice variables were controlled for, a total compensation disparity of $9,695 remained between men and women (95% confidence interval, $8,438-$10,952). A 17-year trend indicates the absolute disparity between men and women has not lessened, although the disparity as a percent of male compensation has decreased in recent years. There remain challenges to ensuring pay equality in the PA profession. Even when compensation-relevant factors such as experience, hours worked, specialty, postgraduate training, region, and call are controlled for, there is still a substantial gender disparity in PA compensation. Remedies that may address this pay inequality include raising awareness of compensation disparities, teaching effective negotiation skills, assisting employers as they develop equitable compensation plans, having less reliance on past salary in position negotiation, and professional associations advocating for policies that support equal wages and opportunities, regardless of personal characteristics. Copyright © 2017 Jacobs Institute of Women's Health. Published by Elsevier Inc. All rights reserved.

In defense of a regulated system of compensation for living donation.

Science.gov (United States)

Matas, Arthur J; Hippen, Benjamin; Satel, Sally

2008-08-01

The organ shortage is the major problem in kidney transplantation today. Despite aggressive organ procurement efforts, the supply of donated kidneys, living and deceased, has not matched the growing demand; as a consequence, more and more qualified candidates are suffering on dialysis and then dying before being transplanted. Herein, we provide justification for a regulated system of compensation for donation. The main argument in favor of compensation is simple-financial incentives will increase donation, so fewer transplant candidates will suffer and die while waiting. In addition, development of a regulated system of compensation is the most effective means of crippling the core economic support for transplant tourism. Because dialysis is so much more expensive than a transplant, compensated donation could be cost-neutral to the healthcare system. Importantly, opinion polls suggest that the public would support compensation. As uncompensated kidney donation is widely accepted, persuasive arguments against compensation must explain why such a system would be morally distinguishable from uncompensated donation. We suggest that the potential advantages of a regulated system of compensation for donation far outweigh any potential disadvantages. It is time to advocate for a change in the law so that trials can be done.

33 CFR 136.217 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.217 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.217...

33 CFR 136.205 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.205 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.205...

33 CFR 136.113 - Other compensation.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT General Procedure § 136.113 Other compensation. A... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Other compensation. 136.113...

20 CFR 211.2 - Definition of compensation.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Definition of compensation. 211.2 Section 211.2 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD RETIREMENT ACT CREDITABLE RAILROAD COMPENSATION § 211.2 Definition of compensation. (a) The term compensation means any form...

Annual compensation for pipelines in Alberta

International Nuclear Information System (INIS)

2008-11-01

The Surface Rights Board (SRB) in Alberta held a hearing in November 2007 to address three issues involving a pipeline for Enbridge Pipelines (Athabasca) Inc. as well as several land owner issues in Townships 66-68 and Ranges 17-19, all west of the 4th Meridian. The issues the SRB examined were the appropriate amount (i.e. magnitude) of compensation payable under right of entry orders under consideration; the appropriate structure of the compensation award; and to whom the compensation was payable. This document presented a review by the Farmer's Advocate Office (FAO) of the published decision of the SRB. The verbatim decision and rationale used by the SRB to award annual compensation for loss and/or ongoing nuisance and inconvenience was presented. The document could be useful to landowners as they determine their negotiation strategy when faced with considering future pipeline access agreements. The document included a discussion of the context for the decision and a case review. Specific topics that were covered included the rationale for the decision; long term effects of pipeline arguments and SRB commentary; the award and determination; and what still needs to be done. It was concluded that the SRB requires evidence in order to answer several questions regarding the magnitude of any losses, and to what degree, if any, had the nuisance, inconvenience, and loss of rights already been anticipated and factored into the operator's final offer

Motion estimation and compensation in dynamic spiral CT reconstruction; Estimation et compensation de mouvement en reconstruction dynamique de tomodensitometrie helicoidale

Energy Technology Data Exchange (ETDEWEB)

Kimdon, J.; Grangeat, P.; Koenig, A.; Bonnet, St

2004-07-01

Respiratory and cardiac motion causes blurring in dynamic X-ray Computed Tomography (CT). Fast scans reduce this problem, but they require a higher radiation dose per time period to maintain the signal to noise ratio of the resulting images, thereby magnifying the health risk to the patient. As an alternative to increased radiation, our team has already developed a cone-beam reconstruction algorithm based on a dynamic particle model that estimates, predicts, and compensates for respiratory motion in circular X-ray CT. The current paper presents an extension of this method to spiral CT, applicable to modern multi-slice scanners that take advantage of the speed and dose benefits of helical trajectories. We adapted all three main areas of the algorithm: backprojection, prediction, and compensation/accumulation. In backprojection, we changed the longitudinal re-binning technique, filter direction, and the method of enforcing the data sufficiency requirements. For prediction, we had to be careful of objects appearing and disappearing as the scanner bed advanced. For compensation/accumulation, we controlled the reconstruction time and combined images to cover a greater longitudinal extent for each phase in the respiratory or cardiac cycle. Tests with moving numerical phantoms demonstrate that the algorithm successfully improves the temporal resolution of the images without increasing the dose or reducing the signal-to-noise ratio. (authors)

Is clinician refusal to treat an emerging problem in injury compensation systems?

Science.gov (United States)

Brijnath, Bianca; Mazza, Danielle; Kosny, Agnieszka; Bunzli, Samantha; Singh, Nabita; Ruseckaite, Rasa; Collie, Alex

2016-01-20

The reasons that doctors may refuse or be reluctant to treat have not been widely explored in the medical literature. To understand the ethical implications of reluctance to treat there is a need to recognise the constraints of doctors working in complex systems and to consider how these constraints may influence reluctance. The aim of this paper is to illustrate these constraints using the case of compensable injury in the Australian context. Between September and December 2012, a qualitative investigation involving face-to-face semistructured interviews examined the knowledge, attitudes and practices of general practitioners (GPs) facilitating return to work in people with compensable injuries. Compensable injury management in general practice in Melbourne, Australia. 25 GPs who were treating, or had treated a patient with compensable injury. The practice of clinicians refusing treatment was described by all participants. While most GPs reported refusal to treat among their colleagues in primary and specialist care, many participants also described their own reluctance to treat people with compensable injuries. Reasons offered included time and financial burdens, in addition to the clinical complexities involved in compensable injury management. In the case of compensable injury management, reluctance and refusal to treat is likely to have a domino effect by increasing the time and financial burden of clinically complex patients on the remaining clinicians. This may present a significant challenge to an effective, sustainable compensation system. Urgent research is needed to understand the extent and implications of reluctance and refusal to treat and to identify strategies to engage clinicians in treating people with compensable injuries. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Center for Worker's Compensation Studies

Data.gov (United States)

Federal Laboratory Consortium — The mission of the NIOSH Center for Workers’ Compensation Studies (CWCS) is to use workers’ compensation data and systems to improve workplace safety and health....

A Novel Temperature Compensation Method for a MEMS Gyroscope Oriented on a Periphery Circuit

Directory of Open Access Journals (Sweden)

Huiliang Cao

2013-09-01

Full Text Available This paper investigates temperature compensation methods used for the scale factor and bias of the MEMS gyroscope within the temperature range from − 40°C to 60°C. The structure and periphery monitor circuit are introduced. Then the determinant elements of the MEMS gyroscope's scale factor are analysed and the results indicate that scale factor is directly proportional to drive amplitude and sense loop gain and is inversely proportional to the frequency gap between two modes. After that, the compensation methods are proposed, the thermal resistor's positive temperature coefficient (tempco is utilized to calibrate the scale factor's tempco through regulating the drive mode amplitude and the sense loop gain, and each method is applied respectively and the results are contrasted. The test results of the two specimens express that the most effective compensation method could decrease the scale factor's tempco from 693ppm/°C (640ppm/°C to 250ppm/°C (257ppm/°C, improving it by 63.9% (59.8%. Finally, a method of declining bias's tempco is investigated and implemented after scale factor compensation. A summator with a thermal resistor is utilized at the output level and decreases the bias's tempco from 103.89°/h/°C (100.78°/h/°C to 9.70°/h/°C (12°/h/°C improving it by 90.7% (88%. Repeat tests are performed based on two specimens to prove the repeatability and reproducibility of the methods.

Capital Structure and Managerial Compensation : The Effects of Renumeration Seniority

NARCIS (Netherlands)

Calcagno, R.; Renneboog, L.D.R.

2004-01-01

We show that the relative seniority of debt and managerial compensation has important implications on the design of remuneration contracts.Whereas the traditional literature assumes that debt is senior to remuneration, we show that this is frequently not the case according to bankruptcy regulation

Capital Structure and Managerial Compensation: the Effects of Remuneration Seniority

NARCIS (Netherlands)

Calcagno, R.; Renneboog, L.

2007-01-01

We show that the relative seniority of debt and managerial compensation has important implications for the design of remuneration contracts. Whereas the traditional literature assumes that debt is senior to remuneration, there are in reality many cases in which remuneration contracts are de facto

Plasticity during vestibular compensation: the role of saccades

Directory of Open Access Journals (Sweden)

Hamish Gavin MacDougall

2012-02-01

Full Text Available This paper is focussed on one major aspect of compensation: the recent behavioural findings concerning oculomotor responses in human vestibular compensation and their possible implications for recovery after unilateral vestibular loss (UVL. New measurement techniques have provided new insights into how patients recover after UVL and have given clues for vestibular rehabilitation. Prior to this it has not been possible to quantify the level of function of all the peripheral vestibular sense organs. Now it is. By using vestibular-evoked myogenic potentials to measure utricular and saccular function and by new video head impulse testing to measure semicircular canal function to natural values of head accelerations. With these new video procedures it is now possible to measure both slow phase eye velocity and also saccades during natural head movements. The present evidence is that there is little or no recovery of slow phase eye velocity responses to natural head accelerations. It is doubtful as to whether the modest changes in slow phase eye velocity to small angular accelerations are functionally effective during compensation. On the other hand it is now clear that saccades can play a very important role in helping patients compensate and return to a normal lifestyle. Preliminary evidence suggests that different patterns of saccadic response may predict how well patients recover. It may be possible to train patients to produce more effective saccadic patterns in the first days after their unilateral loss. Some patients do learn new strategies, new behaviours, to conceal their inadequate VOR but when those strategies are prevented from operating by using passive, unpredictable, high acceleration natural head movements, as in the head impulse test, their vestibular loss can be demonstrated. It is those very strategies which the tests exclude, which may be the cause of their successful compensation.

Compensation Services Advisor | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Job Summary The Compensation Services Advisor is accountable for the effective ... Coordinates the annual Performance Review and Assessment System ... by IDRC and the broader financial and social implications of working in Canada. ... in areas such as mortgages, credit and so on to individuals not accustomed to ...

Compliance Modeling and Error Compensation of a 3-Parallelogram Lightweight Robotic Arm

DEFF Research Database (Denmark)

Wu, Guanglei; Guo, Sheng; Bai, Shaoping

2015-01-01

This paper presents compliance modeling and error compensation for lightweight robotic arms built with parallelogram linkages, i.e., Π joints. The Cartesian stiffness matrix is derived using the virtual joint method. Based on the developed stiffness model, a method to compensate the compliance...... error is introduced, being illustrated with a 3-parallelogram robot in the application of pick-and-place operation. The results show that this compensation method can effectively improve the operation accuracy....

Springback Compensation Based on FDM-DTF Method

International Nuclear Information System (INIS)

Liu Qiang; Kang Lan

2010-01-01

Stamping part error caused by springback is usually considered to be a tooling defect in sheet metal forming process. This problem can be corrected by adjusting the tooling shape to appropriate shape. In this paper, springback compensation based on FDM-DTF method is proposed to be used for design and modification of the tooling shape. Firstly, based on FDM method, the tooling shape is designed by reversing inner force's direction at the end of forming simulation, the required tooling shape can be got through some iterations. Secondly actual tooling is produced based on results got in the first step. When the tooling and part surface discrete data are investigated, the transfer function between numerical springback error and real springback error can be calculated based on wavelet transform results, which can be used in predicting the tooling shape for the desired product. Finally the FDM-DTF method is proved to control springback effectively after it has been applied in the 2D irregular product springback control.

Compensations for increased rotational inertia during human cutting turns.

Science.gov (United States)

Qiao, Mu; Brown, Brian; Jindrich, Devin L

2014-02-01

Locomotion in a complex environment is often not steady state, but unsteady locomotion (stability and maneuverability) is not well understood. We investigated the strategies used by humans to perform sidestep cutting turns when running. Previous studies have argued that because humans have small yaw rotational moments of inertia relative to body mass, deceleratory forces in the initial velocity direction that occur during the turning step, or 'braking' forces, could function to prevent body over-rotation during turns. We tested this hypothesis by increasing body rotational inertia and testing whether braking forces during stance decreased. We recorded ground reaction force and body kinematics from seven participants performing 45 deg sidestep cutting turns and straight running at five levels of body rotational inertia, with increases up to fourfold. Contrary to our prediction, braking forces remained consistent at different rotational inertias, facilitated by anticipatory changes to body rotational speed. Increasing inertia revealed that the opposing effects of several turning parameters, including rotation due to symmetrical anterior-posterior forces, result in a system that can compensate for fourfold changes in rotational inertia with less than 50% changes to rotational velocity. These results suggest that in submaximal effort turning, legged systems may be robust to changes in morphological parameters, and that compensations can involve relatively minor adjustments between steps to change initial stance conditions.

28 CFR 104.21 - Filing for compensation.

Science.gov (United States)

2010-07-01

... “Personal Injury Compensation Form” or a “Death Compensation Form.” A claim shall be deemed “filed” for... filing either a “Personal Injury Compensation Form” or a “Death Compensation Form,” the claim shall be..., when a Claims Evaluator determines that both the Eligibility Form and either a Personal Injury...

The Influence of No Fault Compensation on Functional Outcomes After Lumbar Spine Fusion.

Science.gov (United States)

Montgomery, Alexander Sheriff; Cunningham, John Edward; Robertson, Peter Alexander

2015-07-15

Prospective cohort study and systematic literature review. To compare the functional outcomes for lumbar spinal fusion in both compensation and noncompensation patients in an environment of universal no fault compensation and then to compare these outcomes with those in worker's compensation and nonworkers compensation cohorts from other countries. Compensation has an adverse effect on outcomes in spine fusion possibly based on adversarial environment, delayed resolution of claims and care, and increased compensation associated with prolonged disability. It is unclear whether a universal no fault compensation system would provide different outcomes for these patients. New Zealand's Accident Compensation Corporation (ACC) provides universal no fault compensation for personal injury secondary to accident and offers an opportunity to compare results with differing provision of compensation. A total of 169 patients undergoing lumbar spinal fusion were assessed preoperatively, at 1 year, and at long-term follow-up out to 14 years, using functional outcome measures and health-related quality-of-life measures. Comparison was made between those covered and not covered by ACC for 3 distinct diagnostic categories. A systematic literature review comparing outcomes in Worker's Compensation and non-Compensation cohorts was also performed. The functional outcomes for both ACC and non-ACC cohorts were similar, with significant and comparable improvements over the first year that were then sustained out to long-term follow-up for both cohorts. At long-term follow-up, the health-related quality-of-life measures were the same between the 2 cohorts.The literature review revealed a marked difference in outcomes between worker's compensation and non-worker's compensation cohorts with a near universal inferior outcome for the compensation group. The similarities in outcomes of patients undergoing lumbar spine fusion under New Zealand's universal no fault compensation system, when

Structuring competitive physician compensation models.

Science.gov (United States)

Mobley, Kim; Turcotte, Claire

2010-12-01

When developing and reviewing their physician compensation programs, healthcare organizations should: Understand the market data. Test outcomes of incentive plans for fair market value. Check total compensation for fair market value and reasonableness.

ARCC Teacher Compensation Initiative: Literature Review

Science.gov (United States)

Appalachia Regional Comprehensive Center, 2014

2014-01-01

In February 2014, the Tennessee State Board of Education (SBE) requested that the Appalachia Regional Comprehensive Center (ARCC) provide assistance to the SBE's Basic Education Program (BEP) Review Committee. The SBE requested additional information on the use and effectiveness of market-based teacher compensation and market-based incentives by…

4D in-beam positron emission tomography for verification of motion-compensated ion beam therapy

International Nuclear Information System (INIS)

Parodi, Katia; Saito, Nami; Chaudhri, Naved; Richter, Christian; Durante, Marco; Enghardt, Wolfgang; Rietzel, Eike; Bert, Christoph

2009-01-01

Purpose: Clinically safe and effective treatment of intrafractionally moving targets with scanned ion beams requires dedicated delivery techniques such as beam tracking. Apart from treatment delivery, also appropriate methods for validation of the actual tumor irradiation are highly desirable. In this contribution the feasibility of four-dimensionally (space and time) resolved, motion-compensated in-beam positron emission tomography (4DibPET) was addressed in experimental studies with scanned carbon ion beams. Methods: A polymethyl methracrylate block sinusoidally moving left-right in beam's eye view was used as target. Radiological depth changes were introduced by placing a stationary ramp-shaped absorber proximal of the moving target. Treatment delivery was compensated for motion by beam tracking. Time-resolved, motion-correlated in-beam PET data acquisition was performed during beam delivery with tracking the moving target and prolonged after beam delivery first with the activated target still in motion and, finally, with the target at rest. Motion-compensated 4DibPET imaging was implemented and the results were compared to a stationary reference irradiation of the same treatment field. Data were used to determine feasibility of 4DibPET but also to evaluate offline in comparison to in-beam PET acquisition. Results: 4D in-beam as well as offline PET imaging was found to be feasible and offers the possibility to verify the correct functioning of beam tracking. Motion compensation of the imaged β + -activity distribution allows recovery of the volumetric extension of the delivered field for direct comparison with the reference stationary condition. Observed differences in terms of lateral field extension and penumbra in the direction of motion were typically less than 1 mm for both imaging strategies in comparison to the corresponding reference distributions. However, in-beam imaging retained a better spatial correlation of the measured activity with the delivered

Hall mobility reduction in single-crystalline silicon gradually compensated by thermal donors activation

Science.gov (United States)

Veirman, J.; Dubois, S.; Enjalbert, N.; Garandet, J. P.; Heslinga, D. R.; Lemiti, M.

2010-06-01

This letter focuses on the variation of the Hall majority carrier mobility with the dopant compensation level in purely Boron-doped Czochralski grown silicon single crystals. Compensation was varied continuously at the sample scale via a step by step activation of the oxygen-based thermal donors. At room temperature, we show a strong drop in mobility for high compensation levels in both p- and n-type Si. Mobility models taking into account carrier scattering on ionized impurities and phonons could not reproduce this drop. We conclude that a specific effect of compensation must be taken into account to explain the observed behaviour. We qualitatively discuss physical mechanisms susceptible to reduce mobility in highly compensated Si.

Does CEO compensation impact patient satisfaction?

Science.gov (United States)

Akingbola, Kunle; van den Berg, Herman A

2015-01-01

This study examines the relationship between CEO compensation and patient satisfaction in Ontario, Canada. The purpose of this paper is to determine what impact hospital CEO compensation has on hospital patient satisfaction. The analyses in this study were based on data of 261 CEO-hospital-year observations in a sample of 103 nonprofit hospitals. A number of linear regressions were conducted, with patient satisfaction as the dependent variable and CEO compensation as the independent variable of interest. Controlling variables included hospital size, type of hospital, and frequency of adverse clinical outcomes. CEO compensation does not significantly influence hospital patient satisfaction. Both patient satisfaction and CEO compensation appear to be driven primarily by hospital size. Patient satisfaction decreases, while CEO compensation increases, with the number of acute care beds in a hospital. In addition, CEO compensation does not even appear to moderate the influence of hospital size on patient satisfaction. There are several limitations to this study. First, observations of CEO-hospital-years in which annual nominal CEO compensation was below $100,000 were excluded, as they were not publicly available. Second, this research was limited to a three-year range. Third, this study related the compensation of individual CEOs to a measure of performance based on a multitude of patient satisfaction surveys. Finally, this research is restricted to not-for-profit hospitals in Ontario, Canada. The findings seem to suggest that hospital directors seeking to improve patient satisfaction may find their efforts frustrated if they focus exclusively on the hospital CEO. The findings highlight the need for further research on how CEOs may, through leading and supporting those hospital clinicians and staff that interact more closely with patients, indirectly enhance patient satisfaction. To the best of the authors' knowledge, no research has examined the relationship between

Mandatory IFRS adoption and executive compensation: Evidence from China

Directory of Open Access Journals (Sweden)

Qingchuan Hou

2014-03-01

Full Text Available This study investigates how the mandatory adoption of International Financial Reporting Standards (IFRS affects the contractual benefits of using accounting information to determine executive compensation in China. After controlling for firm and corporate governance characteristics, we find strong evidence supporting the positive role of mandatory IFRS adoption on the accounting-based performance sensitivity of executive compensation. Subsample analysis suggests that improvements in accounting-based performance sensitivity after IFRS adoption differ across regions with various levels of institutional quality and across firms that are affected to a different extent by the adoption. Additional analysis supports the argument that the positive effects of IFRS adoption on the use of accounting performance in executive compensation are driven by the reduction in accounting conservatism associated with IFRS adoption.

Ion-beam plasma and propagation of intense compensated ion beams

Energy Technology Data Exchange (ETDEWEB)

Gabovich, M D [AN Ukrainskoj SSR, Kiev. Inst. Fiziki

1977-02-01

Discussed are the results of investigation of plasma properties received by neutralization of intense ion beam space charge. Considered is the process of ion beam compensation by charges, formed as a result of gas ionization by this beam or by externally introduced ones. Emphasis is placed on collective phenomena in ion-beam plasma, in particular on non-linear effects limiting amplitude of oscillations. It is shown that not only dynamic decompensation but the Coulomb collisions of ions with electrons as well as other collective oscillations significantly affects the propagation of compensated ion beams. All the processes are to be taken into account in solving the problem of obtaining ''superdense'' compensated beams.

Ion-beam plasma and propagation of intense compensated ion beams

International Nuclear Information System (INIS)

Gabovich, M.D.

1977-01-01

Discussed are the results of investigation of plasma properties recieved by neutralization of intensive ion beam space charge. Considered is the process of ion beam compensation by charges, formed as a result of gas ionization by this beam or by externally introduced ones. Emphasis is placed on collective phenomena in ion-beam plasma, in particular on non-linear effects limiting amplitude of oscillations. It is shown, that not only dinamic decompensation but the Coulomb collisions of ions with electrons as well as other collective oscillations significantly affects the propagation of compensated ion beams. All the processes are to be taken into account at solving the problem of obtaining ''superdense'' compensated beams

Compensation for oil pollution damage caused by oil spills from ships and the International Oil Pollution Compensation Fund

International Nuclear Information System (INIS)

Jacobsson, M.

1994-01-01

Liability and compensation for pollution damage caused by oil spills from laden tankers is governed by two international conventions: the 1969 Civil Liability Convention and the 1971 Fund Convention. The Civil Liability Convention established a system of strict liability for tanker owners and introduced compulsory liability insurance. The Fund Convention created a system of supplementary compensation administered by an intergovernmental organization, the International Oil Pollution Compensation Fund (IOPC Fund), which at present has 56 member states (August 1993). The IOPC Fund pays compensation to victims of oil pollution in member states when the compensation from the ship owner and his insurer is insufficient. (author)

Vertical vibration analysis for elevator compensating sheave

Science.gov (United States)

Watanabe, Seiji; Okawa, Takeya; Nakazawa, Daisuke; Fukui, Daiki

2013-07-01

Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified.

Vertical vibration analysis for elevator compensating sheave

International Nuclear Information System (INIS)

Watanabe, Seiji; Nakazawa, Daisuke; Fukui, Daiki; Okawa, Takeya

2013-01-01

Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified

TopSPICE Simulations for Temperature Compensation of ISFET/MEMFET Micro-Sensor

Directory of Open Access Journals (Sweden)

Sawsen AZZOUZI

2014-05-01

Full Text Available In this work, an ISFET (Ion Sensitive Field Effect Transistor/MEMFET (Membrane Field Effect Transistor interface circuit with temperature compensation has been successfully designed and simulated. In each interface, we used the macro-model of ISFET/MEMFET based chemical sensors simulated in TopSPICE. The simulation results of the different sensing circuits of ISFET/MEMFETs for temperature compensation show that the readout configuration for ISFET/MEMFET sensors based on Wheatstone-Bridge connection is the most effective with a temperature drift 5´10-6 mV/°C.

The demand-induced strain compensation model : renewed theoretical considerations and empirical evidence

NARCIS (Netherlands)

de Jonge, J.; Dormann, C.; van den Tooren, M.; Näswall, K.; Hellgren, J.; Sverke, M.

2008-01-01

This chapter presents a recently developed theoretical model on jobrelated stress and performance, the so-called Demand-Induced Strain Compensation (DISC) model. The DISC model predicts in general that adverse health effects of high job demands can best be compensated for by matching job resources

THE EFFECTS OF STOCK OPTION COMPENSATION ONMANAGERIAL RISK TAKING BEHAVIOR AND FIRM FINANCIALPERFORMANCETHE GLOBAL FINANCIAL CRISIS FROM ADIFFERENT PERSPECTIVE

Directory of Open Access Journals (Sweden)

Guler Aras

2012-07-01

Full Text Available The aim of this study is to figure out whether managerial risk taking behaviourand firm financial performance is effected by stock option compensation.Inliterature stock optioncompensationismentionedasa meansto solve agencyproblems. It is analysed how stock option compensation aligns theshareholders’andmanagers’ interestsand its effects on firm financialperformance. Additionally, it isinvestigatedwhether this effecthas a link to theglobal financial crisis which hasobviously related to the managers’extreme riskseeking behaviourespecially in financial sector. Inthis study, 189 firms fromS P index are analysedutilizingthe panel dataanalysismethod between years1998-2009. Additionally, regression method is used to measureeach year. Thedata set is grouped as financial and non financial sector tobetterpresent theeffects of global financial crisis.According to the results of this study, stockoption compensation is positively related to investment magnitudes which aretaken as indicators of risk taking behavior.On the other hand, it is negativelyrelated to firm financial performance.According to the results of yearlycomparison, in financial sector the invesment magnitudes are bigger than the nonfinancial sector just two years before the financial crisis and net cash flow fromthe investing activities is significantly negative when compared with non financialsector.Therefore,it is aimed to findoutthe relation between the extreme riskseeking behaviorbefore the global financial crisisand the incentive compensationstructures.

23 CFR 751.15 - Just compensation.

Science.gov (United States)

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Just compensation. 751.15 Section 751.15 Highways... AND ACQUISITION § 751.15 Just compensation. (a) Just compensation shall be paid the owner for the... nonconforming junkyard as provided in § 751.11 must pertain at the time of the taking or removal in order to...

Radiotherapy dose compensation for lung patients

International Nuclear Information System (INIS)

Piyaratna, N.; Arnold, A.; Metcalfe, P.

1999-01-01

The purpose of the present paper is to provide a more homogeneous dose distribution in the target volume from compensated anterior and posterior fields while the healthy lung is spared by de-weighting the lateral fields. A compensation computation which used linear iterations to compute the most homogeneous dose distribution across the target volume was applied to produce optimum compensator designs. The equivalent tissue-air ratio (E-TAR) inhomogeneity correction was applied for the computations using a GE target series 11 planning computer. The compensators designed were tested for accuracy in a modified water/lung phantom using a scanning diode and an anthropomorphic phantom using thermoluminescent dosimeters. A comparison has been made between the compensated and uncompensated plans for the first nine patients who we have treated with this technique. The dose profiles produced by the computation agreed with the prediction of the computed isodose plans to within ± 2% at the target depth. The thermoluminescent dosimeter (TLD)-measured results in the anthropomorphic phantom agreed with the planning computer within ± 3%. A comparison of nine compensated plans of radiotherapy patients for large-volume targets in the lung region showed a maximum variation in the target to be 19% uncompensated versus 10% compensated. By providing compensated treatment fields from anterior and posterior treatment portals, a homogeneous dose that conforms well to the target volume is provided. As an added bonus, this enables the lateral lung fields to be significantly de-weighted and the healthy lung is spared considerable dose. Copyright (1999) Blackwell Science Pty Ltd

Model-Free Adaptive Control Algorithm with Data Dropout Compensation

Directory of Open Access Journals (Sweden)

Xuhui Bu

2012-01-01

Full Text Available The convergence of model-free adaptive control (MFAC algorithm can be guaranteed when the system is subject to measurement data dropout. The system output convergent speed gets slower as dropout rate increases. This paper proposes a MFAC algorithm with data compensation. The missing data is first estimated using the dynamical linearization method, and then the estimated value is introduced to update control input. The convergence analysis of the proposed MFAC algorithm is given, and the effectiveness is also validated by simulations. It is shown that the proposed algorithm can compensate the effect of the data dropout, and the better output performance can be obtained.

Enthalpy-entropy compensation in protein unfolding

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

Enthalpy-entropy compensation was found to be a universal law in protein unfolding based on over 3 000 experimental data. Water molecular reorganization accompanying the protein unfolding was suggested as the origin of the enthalpy-entropy compensation in protein unfolding. It is indicated that the enthalpy-entropy compensation constitutes the physical foundation that satisfies the biological need of the small free energy changes in protein unfolding, without the sacrifice of the bio-diversity of proteins. The enthalpy-entropy compensation theory proposed herein also provides valuable insights into the Privalov's puzzle of enthalpy and entropy convergence in protein unfolding.

Paid to Perform: Aligning Total Military Compensation With Talent Management. Volume 8

Science.gov (United States)

2015-06-01

study upon which a wider compensation model can be built, we propose a system that thoughtfully integrates rede - signed basic pays and pensions...Taken together, these basic pay and pension rede - sign components will create a far more cost-effective total compensation system than the one

Eco-compensation in China: Theory, practices and suggestions for the future.

Science.gov (United States)

Shang, Wenxiu; Gong, Yicheng; Wang, Zhongjing; Stewardson, Michael J

2018-03-15

Eco-compensation is the most important form of compensatory conservation in China. However, this compensatory mechanism is criticized for vague definition and massive government participation. For better understanding of eco-compensation in China, this paper compares theories and practices of compensatory mechanisms in China and abroad. The analysis of theoretical backgrounds shows that eco-compensation in China is a combination of 'ecological compensation' and 'payments for ecosystem services'. Ten compensatory projects in China and abroad are assessed to reveal characteristics and problems of eco-compensation in China. The results show that compensatory projects in China lagged behind mature foreign compensatory projects in clarity of property rights, responsibility fulfillment, executive efficiency, effectiveness, sustainability and equality. The massive participation of the government is the major reason for the poor performance of compensatory projects in China. However, government participation is necessary at the present stage in China for the income gap and beneficiaries' low willingness to pay. For the improvement of eco-compensation in China, suggestions are given on the choice of non-market valuation methods, the creation of property rights and the establishment of market mechanisms. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects of Target Positioning Error on Motion Compensation for Airborne Interferometric SAR

Directory of Open Access Journals (Sweden)

Li Yin-wei

2013-12-01

Full Text Available The measurement inaccuracies of Inertial Measurement Unit/Global Positioning System (IMU/GPS as well as the positioning error of the target may contribute to the residual uncompensated motion errors in the MOtion COmpensation (MOCO approach based on the measurement of IMU/GPS. Aiming at the effects of target positioning error on MOCO for airborne interferometric SAR, the paper firstly deduces a mathematical model of residual motion error bring out by target positioning error under the condition of squint. And the paper analyzes the effects on the residual motion error caused by system sampling delay error, the Doppler center frequency error and reference DEM error which result in target positioning error based on the model. Then, the paper discusses the effects of the reference DEM error on the interferometric SAR image quality, the interferometric phase and the coherent coefficient. The research provides theoretical bases for the MOCO precision in signal processing of airborne high precision SAR and airborne repeat-pass interferometric SAR.

Trophic compensation reinforces resistance: herbivory absorbs the increasing effects of multiple disturbances.

Science.gov (United States)

Ghedini, Giulia; Russell, Bayden D; Connell, Sean D

2015-02-01

Disturbance often results in small changes in community structure, but the probability of transitioning to contrasting states increases when multiple disturbances combine. Nevertheless, we have limited insights into the mechanisms that stabilise communities, particularly how perturbations can be absorbed without restructuring (i.e. resistance). Here, we expand the concept of compensatory dynamics to include countervailing mechanisms that absorb disturbances through trophic interactions. By definition, 'compensation' occurs if a specific disturbance stimulates a proportional countervailing response that eliminates its otherwise unchecked effect. We show that the compounding effects of disturbances from local to global scales (i.e. local canopy-loss, eutrophication, ocean acidification) increasingly promote the expansion of weedy species, but that this response is countered by a proportional increase in grazing. Finally, we explore the relatively unrecognised role of compensatory effects, which are likely to maintain the resistance of communities to disturbance more deeply than current thinking allows. © 2015 John Wiley & Sons Ltd/CNRS.

The feasibility of the auto tuning respiratory compensation system with ultrasonic image tracking technique.

Science.gov (United States)

Chuang, Ho-Chiao; Hsu, Hsiao-Yu; Nieh, Shu-Kan; Tien, Der-Chi

2015-01-01

The purpose of this study is to assess the feasibility of using the analytical technique of ultrasound images in combination with an auto tumor localization system. During respiration, the activity of breathing in and out causes organs displacement at the lower lobe of the lung, and the maximum displacement range happens in the Superior-Inferior (SI) direction. Therefore, in this study all the tumor positioning is in SI direction under respiratory compensation, in which the compensations are carried out to the organs at the lower lobe and adjacent to the lower lobe of lung.In this research, due to the processes of ultrasound imaging generation, image analysis and signal transmission, when the captured respiratory signals are sent to auto tumor localization system, there was a signal time delay. The total delay time of the entire signal transmission process was 0.254 ± 0.023 seconds (with the lowest standard deviation) after implementing a series of analyses. To compensate for this signal delay time (0.254 ± 0.023 sec), a phase lead compensator (PLC) was designed and built into the auto tumor localization system. By analyzing the impact of the delay time and the respiratory waveforms under different frequencies on the phase lead compensator, an overall system delay time can be configured. Results showed as the respiratory frequency increased, variable value ``a'' and the subsequent gain ``k'' in the controller becomes larger. Moreover, value ``a'' and ``k'' increased as the system delay time increased when the respiratory frequency was fixed. The relationship of value ``a'' and ``k'' to the respiratory frequency can be obtained by using the curve fitting method to compensate for the respiratory motion for tumor localization. Through the comparison of the uncompensated signal and the compensated signal performed by the auto tumor localization system on the simulated respiratory signal, the feasibility of using ultrasound image analysis technology combined with the

Flexible Compensation of Voltage and Current Unbalance and Harmonics in Microgrids

DEFF Research Database (Denmark)

Mousazadeh, Seyyed Yousef; Jalilian, Alireza; Savaghebi, Mehdi

2017-01-01

In recent years, the harmonics and unbalance problem endanger the voltage and current quality of power systems due to increasing usage of nonlinear and unbalance loads. Using DG interfacing inverters is proposed for voltage or current compensation. In this paper, a flexible control method...... is proposed to compensate voltage and current unbalance and harmonics using the Distributed Generation (DG) interfacing inverters. This method is applicable to both grid-connected and islanded microgrids. In the proposed method, not only the proper control of active and reactive powers can be achieved......) frame. An extensive simulation study has been performed and the results demonstrate the effectiveness of the proposed control scheme. The results show that depending on the compensation mode, the harmonics and unbalance compensation of DGs’ output current, MG’s injected current to the grid as well...

A motion-compensated cone-beam CT using electrical impedance tomography imaging

International Nuclear Information System (INIS)

Pengpan, T; Smith, N D; Qiu, W; Yao, A; Mitchell, C N; Soleimani, M

2011-01-01

Cone-beam CT (CBCT) is an imaging technique used in conjunction with radiation therapy. For example CBCT is used to verify the position of lung cancer tumours just prior to radiation treatment. The accuracy of the radiation treatment of thoracic and upper abdominal structures is heavily affected by respiratory movement. Such movement typically blurs the CBCT reconstruction and ideally should be removed. Hence motion-compensated CBCT has recently been researched for correcting image artefacts due to breathing motion. This paper presents a new dual-modality approach where CBCT is aided by using electrical impedance tomography (EIT) for motion compensation. EIT can generate images of contrasts in electrical properties. The main advantage of using EIT is its high temporal resolution. In this paper motion information is extracted from EIT images and incorporated directly in the CBCT reconstruction. In this study synthetic moving data are generated using simulated and experimental phantoms. The paper demonstrates that image blur, created as a result of motion, can be reduced through motion compensation with EIT

Addressing inadequate compensation | IDRC - International ...

International Development Research Centre (IDRC) Digital Library (Canada)

2016-08-12

Aug 12, 2016 ... The issue LSLAs raise a number of concerns regarding compensation, including ... at a meeting with traders in Lamu, Kenya, where a new port is planned. ... compensation and a fair share of benefits and risks in land deals.

Voltage Sag Compensator for CAR and SOR of HANARO

International Nuclear Information System (INIS)

Kim, Hyung-Kyoo; Jung, Hoan-Sung; Wu, Jong-Sup

2007-01-01

HANARO is designed so as to be tripped automatically by insertion of control absorber rods(CAR) and shut-off rods(SOR) and the process systems, such as primary cooling system, secondary cooling system and reflector cooling system, etc., stop whenever the off-site power failure occurs, the reactor trips automatically. When voltage sag or momentary interruption occurs, the process systems are in operation but the reactor has an unwanted trip by insertion of CARs and SORs. We installed the voltage sag compensator on the power supply for CARs and SORs so as to prevent a nuisance trip. The compensated time is decided not to exceed 1 sec in consideration of reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator

Apparent directional selection by biased pleiotropic mutation.

Science.gov (United States)

Tanaka, Yoshinari

2010-07-01

Pleiotropic effects of deleterious mutations are considered to be among the factors responsible for genetic constraints on evolution by long-term directional selection acting on a quantitative trait. If pleiotropic phenotypic effects are biased in a particular direction, mutations generate apparent directional selection, which refers to the covariance between fitness and the trait owing to a linear association between the number of mutations possessed by individuals and the genotypic values of the trait. The present analysis has shown how the equilibrium mean value of the trait is determined by a balance between directional selection and biased pleiotropic mutations. Assuming that genes act additively both on the trait and on fitness, the total variance-standardized directional selection gradient was decomposed into apparent and true components. Experimental data on mutation bias from the bristle traits of Drosophila and life history traits of Daphnia suggest that apparent selection explains a small but significant fraction of directional selection pressure that is observed in nature; the data suggest that changes induced in a trait by biased pleiotropic mutation (i.e., by apparent directional selection) are easily compensated for by (true) directional selection.

THE INFLUENCE OF JOB STRESS AND COMPENSATION TO JOB SATISFACTION AT PT. TRI MEGAH MAKMUR

Directory of Open Access Journals (Sweden)

I Ketut R Sudiarditha

2016-09-01

Full Text Available The purpose of this research are: 1 To know description and how picture level job stress, compensation and job satisfaction at PT Tri Megah Makmur. 2 To know the influence of job stress tojob satisfaction at PT Tri Megah Makmur. 3 To know the influence of compensation to job satisfaction at PT Tri Megah Makmur. 4 To know empirically the influence of job stress and compensation tojob satisfaction at PT Tri Megah Makmur. 5 To know how far the contribution of job stress and compensation to job satisfaction at PT Tri Megah Makmur. This research is using descriptive and explanatory survey analysis. This research is taken to 70 sales employees at PT Tri Megah Makmur, While the data collection technique was carried out by spreading kuisioner, which are then processed using SPSS versi 21.00.The analysis shows that: 1 level of compensation and job satisfaction are on a lower level, while the job stress are high. 2Job stress have negative effects and significantly on job satisfaction. 3 compensation have positive effect and significantly on job satisfaction. 4 job stress and compensation significantly influence on job satisfaction.

Tumor tracking and motion compensation with an adaptive tumor tracking system (ATTS): System description and prototype testing

International Nuclear Information System (INIS)

Wilbert, Juergen; Meyer, Juergen; Baier, Kurt; Guckenberger, Matthias; Herrmann, Christian; Hess, Robin; Janka, Christian; Ma Lei; Mersebach, Torben; Richter, Anne; Roth, Michael; Schilling, Klaus; Flentje, Michael

2008-01-01

A novel system for real-time tumor tracking and motion compensation with a robotic HexaPOD treatment couch is described. The approach is based on continuous tracking of the tumor motion in portal images without implanted fiducial markers, using the therapeutic megavoltage beam, and tracking of abdominal breathing motion with optical markers. Based on the two independently acquired data sets the table movements for motion compensation are calculated. The principle of operation of the entire prototype system is detailed first. In the second part the performance of the HexaPOD couch was investigated with a robotic four-dimensional-phantom capable of simulating real patient tumor trajectories in three-dimensional space. The performance and limitations of the HexaPOD table and the control system were characterized in terms of its dynamic behavior. The maximum speed and acceleration of the HexaPOD were 8 mm/s and 34.5 mm/s 2 in the lateral direction, and 9.5 mm/s and 29.5 mm/s 2 in longitudinal and anterior-posterior direction, respectively. Base line drifts of the mean tumor position of realistic lung tumor trajectories could be fully compensated. For continuous tumor tracking and motion compensation a reduction of tumor motion up to 68% of the original amplitude was achieved. In conclusion, this study demonstrated that it is technically feasible to compensate breathing induced tumor motion in the lung with the adaptive tumor tracking system

What Constitutes Fair Compensation for Unfair Dismissal

African Journals Online (AJOL)

user

Generally the monetary compensation is perceived to be a solatium. 19 .... compensation for non-patrimonial loss in the context of an unfair labour practice. 41 .... awards of compensation where a person's dignity is impaired in the course of an.

Compensating citizens for poor service delivery: experimental research in public and private settings

OpenAIRE

Thomassen, JP; Leliveld, MC; Van de Walle, Steven; Ahaus, K

2017-01-01

After a service failure, citizens expect a recovery strategy that restores perceived justice and places a reasonable value on their loss. Offering monetary compensation is a strategy commonly used in private settings, but less so in public settings. To date compensation effects have not been researched in public settings. To investigate citizens’ evaluations of perceived justice, negative emotions and post-recovery satisfaction we used a 2 (sector: public, private) by 2 (compensation promised...

Compensative hypertrophy of the kidney

International Nuclear Information System (INIS)

Raynaud, C.

1976-01-01

Several measurement methods are available to practitioners to reveal a compensative hypertrophy. Mensuration of the kidney has the advantage of simplicity but is in fact an unreliable and inaccurate method. Separate clearances in their traditional form have never entered into routine use because of the disadvantages of ureteral catheterism. The use of radioactive tracers avoids this drawback, but clearances calculated in this way are only valid in the absence of obstructive urinary disorders. Solutions have been proposed, but the values obtained are no longer identical with the clearances. The Hg uptake test quantifies quite accurately the function of each kidney. From the results obtained a complete compensative hypertrophy developed on a healthy kidney and an incomplete compensative hypertrophy developed on the diseased kidney have been described. In each of these situations the degree to which compensative hypertrophy develops seems to be fixed at a given level peculiar to each patient [fr

Defining Compensable Injury in Biomedical Research.

Science.gov (United States)

Larkin, Megan E

2015-01-01

Biomedical research provides a core social good by enabling medical progress. In the twenty-first century alone, this includes reducing transmission of HIV/AIDS, developing innovative therapies for cancer patients, and exploring the possibilities of personalized medicine. In order to continue to advance medical science, research relies on the voluntary participation of human subjects. Because research is inherently uncertain, unintended harm is an inevitable part of the research enterprise. Currently, injured research participants in the United States must turn to the “litigation lottery” of the tort system in search of compensation. This state of affairs fails research participants, who are too often left uncompensated for devastating losses, and makes the United States an outlier in the international community. In spite of forty years’ worth of Presidential Commissions and other respected voices calling for the development of a no-fault compensation system, no progress has been made to date. One of the reasons for this lack of progress is the failure to develop a coherent ethical basis for an obligation to provide compensation for research related injuries. This problem is exacerbated by the lack of a clear definition of “compensable injury” in the biomedical research context. This article makes a number of important contributions to the scholarship in this growing field. To begin, it examines compensation systems already in existence and concludes that there are four main definitional elements that must be used to define “compensable injury.” Next, it examines the justifications that have been put forth as the basis for an ethical obligation to provide compensation, and settles on retrospective nonmaleficence and distributive and compensatory justice as the most salient and persuasive. Finally, it uses the regulatory elements and the justifications discussed in the first two sections to develop a well-rounded definition of “compensable injury�

[Incentive for Regional Risk Selection in the German Risk Structure Compensation Scheme].

Science.gov (United States)

Wende, Danny

2017-10-01

The introduction of the new law GKV-FQWG strengthens the competition between statutory health insurance. If incentives for risk selection exist, they may force a battle for cheap customers. This study aims to document and discuss incentives for regional risk selection in the German risk structure compensation scheme. Identify regional autocorrelation with Moran's l on financial parameters of the risk structure compensation schema. Incentives for regional risk selection do indeed exist. The risk structure compensation schema reduces 91% of the effect and helps to reduce risk selection. Nevertheless, a connection between regional situation and competition could be shown (correlation: 69.5%). Only the integration of regional control variables into the risk compensation eliminates regional autocorrelation. The actual risk structure compensation is leading to regional inequalities and as a consequence to risk selection and distortion in competition. © Georg Thieme Verlag KG Stuttgart · New York.

Joint compensation of multiple RF impairments in MIMO STBC systems

KAUST Repository

Qi, Jian

2011-09-01

In this paper, we propose a compensation method for the joint effect of high-power amplifier (HPA) nonlinearity, in-phase/quadrature-phase (I/Q) imbalance and crosstalk in multiple-input multiple-output (MIMO) orthogonal space-time block coding (OSTBC) systems. The performance of the MIMO OSTBC equipped with the proposed compensation mechanism is evaluated in terms of average symbol error probability and system capacity, in Rayleigh fading channels. Numerical results are provided and show the effects on performance of several system parameters, namely, the HPA parameters, image-leakage ratio, crosstalk, numbers of antennas, and phase-shift keying modulation order. © 2011 IEEE.

Robust Nonlinear Control with Compensation Operator for a Peltier System

Directory of Open Access Journals (Sweden)

Sheng-Jun Wen

2014-01-01

Full Text Available Robust nonlinear control with compensation operator is presented for a Peltier actuated system, where the compensation operator is designed by using a predictive model on heat radiation. For the Peltier system, the heat radiation is related to the fourth power of temperature. So, the heat radiation is affected evidently by the temperature when it is high and temperature difference between the system and environment is large. A new nonlinear model with the heat radiation is set up for the system according to some thermal conduction laws. To ensure robust stability of the nonlinear system, operator based robust right coprime factorization design is considered. Also, a compensation operator based on a predictive model is proposed to cancel effect of the heat radiation, where the predictive model is set up by using radial basis kernel function based SVM (support vector machine method. Finally, simulation results are given to show the effectiveness of the proposed scheme.

38 CFR 3.5 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation General § 3.5 Dependency and indemnity compensation. (a) Dependency and indemnity compensation. This term means a monthly payment made by...

Refractive index sensor based on optical fiber end face using pulse reference-based compensation technique

Science.gov (United States)

Bian, Qiang; Song, Zhangqi; Zhang, Xueliang; Yu, Yang; Chen, Yuzhong

2018-03-01

We proposed a refractive index sensor based on optical fiber end face using pulse reference-based compensation technique. With good compensation effect of this compensation technique, the power fluctuation of light source, the change of optic components transmission loss and coupler splitting ratio can be compensated, which largely reduces the background noise. The refractive index resolutions can achieve 3.8 × 10-6 RIU and1.6 × 10-6 RIU in different refractive index regions.

AN IMPROVED CONTROL ALGORITHM FOR «DYNAMIC CAPACITOR» VAR COMPENSATOR

Directory of Open Access Journals (Sweden)

S.K. Podnebennaya

2015-11-01

Full Text Available Purpose. Modern approaches of VAR compensation are: using compensators with stepped regulation, STATCOMs, active power filters. Recently, more attention is paid to VAR compensator’s design based on the direct AC / AC converters, which are called dynamic capacitors. Methodology. The dynamic capacitor (D-CAP is the capacitor bank, which is connected to the mains through direct AC / AC buck converter. By varying the duty cycle of bidirectional switches, smooth control of reactive power can be achieved. However, in case of distorted mains voltage, D-CAP mains current will have a high THD. This is due to the fact that the D-CAP affects the frequency response of electric grid thus leading to the appearance of resonances. With non-sinusoidal mains voltage, capacitors are affected by harmonics. This reduces the reliability of the D-CAP, increasing the probability of their failure. To eliminate these drawbacks it is suggested to improve the D-CAP control system so that the input current of the dynamic capacitor is forced to be close to sinusoidal. This can be achieved if the duty cycle of the switching bi-directional switches is changed according to the proposed expression. Results. The research is done on a single-phase D-CAP with the proposed control system, its input current diagrams are shown. In contrast to the D-CAP with a constant duty cycle control, the resulting THD of its input current is much lower. Thus, the control system provides a form of the input current that is close to a sine wave. This reduces the influence of mains voltage harmonics on the D-CAP operation, increases its reliability and improves power quality. Originality. The proposed D-CAP control system ensures reliable operation with non-sinusoidal mains voltage. Practical value. Application of D-CAPs with the proposed control system allows for improved energy efficiency of electrical mains by providing VAR compensation and improving power quality.

Compensating customer-generators: a taxonomy describing methods of compensating customer-generators for electricity supplied to the grid

International Nuclear Information System (INIS)

Hughes, Larry; Bell, Jeff

2006-01-01

The increasing popularity of on-site power generation is driving the demand for methods to compensate customer-generators that supply electricity to the grid. Although many practices exist for providing such compensation, confusion surrounds the terms often used to describe such practices (notably, net metering and net billing). To help clarify this situation, the following paper proposes a taxonomy that distinguishes between 16 distinct compensation practices

Hysteresis and compensation behaviors of spin-3/2 cylindrical Ising nanotube system

International Nuclear Information System (INIS)

Kocakaplan, Yusuf; Keskin, Mustafa

2014-01-01

The hysteresis and compensation behaviors of the spin-3/2 cylindrical Ising nanotube system are studied within the framework of the effective-field theory with correlations. The effects of the Hamiltonian parameters are investigated on the magnetic and thermodynamic quantities, such as the total magnetization, hysteresis curves, and compensation behaviors of the system. Depending on the Hamiltonian parameters, some characteristic hysteresis behaviors are found, such as the existence of double and triple hysteresis loops. According to Néel classification nomenclature, the system displays Q-, R-, P-, N-, M-, and S- types of compensation behaviors for the appropriate values of the system parameters. We also compare our results with some recently published theoretical and experimental works and find a qualitatively good agreement

Hysteresis and compensation behaviors of spin-3/2 cylindrical Ising nanotube system

Energy Technology Data Exchange (ETDEWEB)

Kocakaplan, Yusuf [Graduate School of Natural and Applied Sciences, Erciyes University, 38039 Kayseri (Turkey); Keskin, Mustafa, E-mail: keskin@erciyes.edu.tr [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)

2014-09-07

The hysteresis and compensation behaviors of the spin-3/2 cylindrical Ising nanotube system are studied within the framework of the effective-field theory with correlations. The effects of the Hamiltonian parameters are investigated on the magnetic and thermodynamic quantities, such as the total magnetization, hysteresis curves, and compensation behaviors of the system. Depending on the Hamiltonian parameters, some characteristic hysteresis behaviors are found, such as the existence of double and triple hysteresis loops. According to Néel classification nomenclature, the system displays Q-, R-, P-, N-, M-, and S- types of compensation behaviors for the appropriate values of the system parameters. We also compare our results with some recently published theoretical and experimental works and find a qualitatively good agreement.

Induction motor IFOC based speed-controlled drive with asymptotic disturbance compensation

Directory of Open Access Journals (Sweden)

Stojić Đorđe M.

2012-01-01

Full Text Available This paper presents the design of digitally controlled speed electrical drive, with the asymptotic compensation of external disturbances, implemented by using the IFOC (Indirect Field Oriented Control torque controlled induction motor. The asymptotic disturbance compensation is achieved by using the DOB (Disturbance Observer with the IMP (Internal Model Principle. When compared to the existing IMP-based DOB solutions, in this paper the robust stability and disturbance compensation are improved by implementing the minimal order DOB filter. Also, the IMP-based DOB design is improved by employing the asymptotic compensation of all elemental or more complex external disturbances. The dynamic model of the IFOC torque electrical drive is, also, included in the speed-controller and DOB section design. The simulation and experimental measurements presented in the paper illustrate the effectiveness and robustness of the proposed control scheme.

Takeovers and (Excess) CEO Compensation

NARCIS (Netherlands)

Feito Ruiz, Isabel; Renneboog, Luc

2017-01-01

We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

Takeovers and (excess) CEO compensation

NARCIS (Netherlands)

Feito Ruiz, Isabel; Renneboog, Luc

We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

Intensity modulated radiotherapy (IMRT) with compensators

International Nuclear Information System (INIS)

Salz, H.; Wiezorek, T.; Scheithauer, M.; Kleen, W.; Schwedas, M.; Wendt, T.G.

2002-01-01

The irradiation with intensity-modulated fields is possible with static as well as dynamic methods. In our university hospital, the intensity-modulated radiotherapy (IMRT) with compensators was prepared and used for the first time for patient irradiation in July 2001. The compensators consist of a mixture of tin granulate and wax, which is filled in a milled negative mould. The treatment planning is performed with Helax-TMS (MDS Nordion). An additional software is used for editing the modulation matrix ('Modifix'). Before irradiation of the first patient, extensive measurements have been carried out in terms of quality assurance of treatment planning and production of compensators. The results of the verification measurements have shown that IMRT with compensators possesses high spatial and dosimetric exactness. The calculated dose distributions are applied correctly. The accuracy of the calculated monitor units is normally better than 3%; in small volumes, further dosimetric inaccuracies between calculated and measured dose distributions are mostly less than 3%. Therefore, the compensators contribute to the achievement of high-level IMRT even when apparatuses without MLC are used. This paper describes the use of the IMRT with compensators, presents the limits of this technology, and discusses the first practical experiences. (orig.) [de

Multipurpose Compensation Scheme for Voltage Sag/Swell and Selective Harmonics Elimination in Distribution Systems

Directory of Open Access Journals (Sweden)

Mustafa Inci

2018-01-01

Full Text Available Voltage harmonics, sag, and swell are the most harmful disturbances in distribution systems. This paper introduces a novel effective controller method for simultaneous compensation of both voltage sag/swell and voltage harmonics by using multifunctional dynamic voltage restorer. In proposed controller method called FFT with integrated ISRF, ISRF detects the magnitudes of voltage sag/swell quickly and precisely, and FFT extracts the selective components of voltage harmonics very effectively. The proposed method integrates the superior properties of ISRF and FFT methods. FFT integrated ISRF is applied for the first time to provide the compensation of both sag/swell and selective harmonics together. The proposed system has ability to compensate symmetrical/asymmetrical sag/swell and symmetrical/asymmetrical selective harmonics which are 5th, 7th, 11th and 13th. The controlled system is modelled in PSCAD/EMDTC and compared with conventional methods. The performance results verify that the proposed method compensates voltage disturbances effectively in the system.

Quasi-eccentricity error modeling and compensation in vision metrology

Science.gov (United States)

Shen, Yijun; Zhang, Xu; Cheng, Wei; Zhu, Limin

2018-04-01

Circular targets are commonly used in vision applications for its detection accuracy and robustness. The eccentricity error of the circular target caused by perspective projection is one of the main factors of measurement error which needs to be compensated in high-accuracy measurement. In this study, the impact of the lens distortion on the eccentricity error is comprehensively investigated. The traditional eccentricity error turns to a quasi-eccentricity error in the non-linear camera model. The quasi-eccentricity error model is established by comparing the quasi-center of the distorted ellipse with the true projection of the object circle center. Then, an eccentricity error compensation framework is proposed which compensates the error by iteratively refining the image point to the true projection of the circle center. Both simulation and real experiment confirm the effectiveness of the proposed method in several vision applications.

50 CFR 296.4 - Claims eligible for compensation.

Science.gov (United States)

2010-10-01

... compensation. (a) Claimants. Damage or loss eligible for Fund compensation must be suffered by a commercial fisherman. (b) Damage or loss of fishing gear. Damage or loss is eligible for Fund compensation if it was... is not eligible for Fund compensation: (1) If the damage or loss was caused by the negligence or...

Economic compensation standard for irrigation processes to safeguard environmental flows in the Yellow River Estuary, China

Science.gov (United States)

Pang, Aiping; Sun, Tao; Yang, Zhifeng

2013-03-01

SummaryAgriculture and ecosystems are increasingly competing for water. We propose an approach to assess the economic compensation standard required to release water from agricultural use to ecosystems while taking into account seasonal variability in river flow. First, we defined agricultural water shortage as the difference in water volume between agricultural demands and actual supply after maintaining environmental flows for ecosystems. Second, we developed a production loss model to establish the relationship between production losses and agricultural water shortages in view of seasonal variation in river discharge. Finally, we estimated the appropriate economic compensation for different irrigation stakeholders based on crop prices and production losses. A case study in the Yellow River Estuary, China, demonstrated that relatively stable economic compensation for irrigation processes can be defined based on the developed model, taking into account seasonal variations in river discharge and different levels of environmental flow. Annual economic compensation is not directly related to annual water shortage because of the temporal variability in river flow rate and environmental flow. Crops that have stable planting areas to guarantee food security should be selected as indicator crops in economic compensation assessments in the important grain production zone. Economic compensation may be implemented by creating funds to update water-saving measures in agricultural facilities.

Compensating citizens for poor service delivery : Experimental research in public and private settings

NARCIS (Netherlands)

Thomassen, Jean Pierre; Leliveld, Marijke C.; Van de Walle, Steven; Ahaus, Kees

2017-01-01

After a service failure, citizens expect a recovery strategy that restores perceived justice and places a reasonable value on their loss. Offering monetary compensation is a strategy commonly used in private settings, but less so in public settings. To date, compensation effects have not been

Executive Compensation and the Cost of Debt

NARCIS (Netherlands)

Kabir, Rezaul; Liu, Hao; Veld-Merkoulova, Yulia V.

2013-01-01

This study examines how different components of executive compensation affect the cost of debt. We find that debt-like and equity-like pay components have differing effects: an increase in defined benefit pensions is associated with lower bond yield spread, while higher share holdings lead to higher

Neuroendocrine and renal effects of intravascular volume expansion in compensated heart failure

DEFF Research Database (Denmark)

Gabrielsen, A; Bie, P; Holstein-Rathlou, N H

2001-01-01

To examine if the neuroendocrine link between volume sensing and renal function is preserved in compensated chronic heart failure [HF, ejection fraction 0.29 +/- 0.03 (mean +/- SE)] we tested the hypothesis that intravascular and central blood volume expansion by 3 h of water immersion (WI) elicits...... sustained angiotensin-converting enzyme inhibitor therapy, n = 9) absolute and fractional sodium excretion increased (P Renal free water clearance increased during WI in control subjects but not in HF......, albeit plasma vasopressin concentrations were similar in the two groups. In conclusion, the neuroendocrine link between volume sensing and renal sodium excretion is preserved in compensated HF. The natriuresis of WI is, however, modulated by the prevailing ANG II and Aldo concentrations. In contrast...

14 CFR 250.8 - Denied boarding compensation.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Denied boarding compensation. 250.8 Section... PROCEEDINGS) ECONOMIC REGULATIONS OVERSALES § 250.8 Denied boarding compensation. (a) Every carrier shall tender to a passenger eligible for denied boarding compensation, on the day and place the denied boarding...

10 CFR 39.53 - Energy compensation source.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Energy compensation source. 39.53 Section 39.53 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.53 Energy compensation source. The licensee may use an energy compensation source (ECS) which is...

Experimental evaluation of voltage unbalance compensation in an islanded microgrid

DEFF Research Database (Denmark)

Savaghebi, Mehdi; Guerrero, Josep M.; Jalilian, Alireza

2011-01-01

In this paper, a method for voltage unbalance compensation in an islanded microgrid based on the proper control of distributed generators (DGs) interface converter is proposed. In this method, active and reactive power control loops are considered to control the power sharing among the DGs. Also......, a virtual impedance loop and voltage and current proportional-resonant controllers are included. Experimental results show the effectiveness of the proposed method for compensating voltage unbalance to an acceptable level....

Technology of VAr Compensators for Induction Generator Applications in Wind Energy Conversion Systems

Directory of Open Access Journals (Sweden)

A. F. Zobaa

2006-09-01

Full Text Available Many of today utility interconnected wind farms use induction generator (IG to convert the captured wind mechanical power into electricity. Induction generator has some advantages over the synchronous generator (SG. The main advantages are its robustness and its capability to be synchronized directly to the grid. The main disadvantage, however, is its dependency on the grid for supplying its own reactive power ‘VAr’. Whether fixed or adjustable VAr systems are connected across its terminal, IG must operate at unity power factor at the rated loading while the wind power varies. With supervised control and appropriate coordination, VAr can be used to the benefits of both the wind farm developer and the hosting utility. The incorporation of today adjustable reactive power compensators such as the Static VAr Compensation (SVC and Static Synchronous Compensator (STATCOM with IG are vital ingredient toward a successful penetration of wind energy in today distribution grid to ensure voltage stability during the steady state and transient periods.

State responsibility and compensation for climate change damages - a legal and economic assessment

International Nuclear Information System (INIS)

Tol, R.S.J.; Institute for Environmental Studies, Amsterdam; Carnegie Mellon University, Pittsburgh, PA; Verheyen, R.

2004-01-01

Customary international law has that countries may do each other no harm. A country violates this rule if an activity under its control does damage to another country, and if this is done on purpose or due to carelessness. Impacts of climate change fall under this rule, which is reinforced by many declarations and treaties,including the UNFCCC. Compensation for the harm done depends on many parameters, such as emission scenarios, climate change, climate change impacts and its accounting. The compensation paid by the OECD may run up to 4% of its GDP, far exceeding the costs of climate change to the OECD directly. However, the most crucial issues are, first, from when countries can be held responsible and, second, which emissions are acceptable and which careless. This may even be interpreted such that the countries of the OECD are entitled to compensation, rather than be obliged to pay. State responsibility could substantially change international climate policy. (author)

Motion estimation and compensation in dynamic spiral CT reconstruction

International Nuclear Information System (INIS)

Kimdon, J.; Grangeat, P.; Koenig, A.; Bonnet, St.

2004-01-01

Respiratory and cardiac motion causes blurring in dynamic X-ray Computed Tomography (CT). Fast scans reduce this problem, but they require a higher radiation dose per time period to maintain the signal to noise ratio of the resulting images, thereby magnifying the health risk to the patient. As an alternative to increased radiation, our team has already developed a cone-beam reconstruction algorithm based on a dynamic particle model that estimates, predicts, and compensates for respiratory motion in circular X-ray CT. The current paper presents an extension of this method to spiral CT, applicable to modern multi-slice scanners that take advantage of the speed and dose benefits of helical trajectories. We adapted all three main areas of the algorithm: backprojection, prediction, and compensation/accumulation. In backprojection, we changed the longitudinal re-binning technique, filter direction, and the method of enforcing the data sufficiency requirements. For prediction, we had to be careful of objects appearing and disappearing as the scanner bed advanced. For compensation/accumulation, we controlled the reconstruction time and combined images to cover a greater longitudinal extent for each phase in the respiratory or cardiac cycle. Tests with moving numerical phantoms demonstrate that the algorithm successfully improves the temporal resolution of the images without increasing the dose or reducing the signal-to-noise ratio. (authors)

Thin hybrid pixel assembly fabrication development with backside compensation layer

Energy Technology Data Exchange (ETDEWEB)

Bates, R., E-mail: richard.bates@glasgow.ac.uk [Experimental Particle Physics Group, SUPA School of Physics and Astronomy, The University of Glasgow, Glasgow G12 8QQ (United Kingdom); Buttar, C.; McMullen, T.; Cunningham, L.; Ashby, J.; Doherty, F. [Experimental Particle Physics Group, SUPA School of Physics and Astronomy, The University of Glasgow, Glasgow G12 8QQ (United Kingdom); Pares, G.; Vignoud, L.; Kholti, B. [CEA Leti, MINATEC, 17 rue des Martyrs, F38054, Grenoble (France); Vahanen, S. [Advacam Oy, Tietotie 3, 02150 Espoo (Finland)

2017-02-11

The ATLAS and CMS experiments will both replace their entire tracking systems for operation at the HL-LHC in 2026. This will include a significantly larger pixel systems, for example, for ATLAS approximately 15 m{sup 2}. To keep the tracker material budget low it is crucial to minimize the mass of the pixel modules via thinning both the sensor and readout chip to about 150 μm each. The bump yield of thin module assemblies using solder based bump bonding can be problematic due to wafer bowing during solder reflow at high temperature. A new bump-bonding process using backside compensation on the readout chip to address the issue of low yield will be presented. The objective is to compensate dynamically the stress of the front side stack by adding a compensating layer to the backside of the wafer. A SiN and Al:Si stack has been chosen for the backside layer. The bow reducing effect of applying a backside compensation layer will be demonstrated using the FE-I4 wafer. The world's first results from assemblies produced from readout wafers thinned to 100 μm with a stress compensation layer are presented with bond yields close to 100% measured using the FE-I4 readout chip.

Hydration of mineral shrinkage-compensating admixture for concrete : an experimental and numerical study

NARCIS (Netherlands)

Chen, Wei; Brouwers, H.J.H.

2012-01-01

The use of shrinkage-compensating admixture in concrete has been proven to be an effective way to mitigate the shrinkage of concrete. The hydration of a shrinkage-compensating admixture in cement paste and concrete is investigated in this paper with numerical simulation and experimental study. An

Installation of the sag compensator for HANARO

International Nuclear Information System (INIS)

Kim, Hyung Kyoo; Jung, Hoan Sung; Lim, In Cheol; Ahn, Guk Hoon

2008-01-01

Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extent of sags occur. HANARO has the reactor regulation system(RRs) and reactor protection system(RPS). HANARO is designed so as to be tripped automatically by insertion of control absorber rods(CAR) and shut off rods(SOR). When voltage sag or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator

Independent versus non-independent outside directors in European companies: Who has a say on CEO compensation?

Directory of Open Access Journals (Sweden)

Pablo de Andrés

2017-04-01

Full Text Available Our study reveals how two separate dimensions of board composition—the proportion of independent directors and of non-independent directors—influence CEO compensation in Western European firms. Controlling for the simultaneous determination of CEO pay structure and board design, we find that firms with a higher proportion of non-independent outsiders on their boards pay less direct compensation (salary + bonus and less equity-linked compensation to their CEOs. By contrast, CEOs working for firms with more independent boards receive more equity based-pay. When we control for the fact that equity linked is not granted systematically in Europe we find that firms with more independent directors on the board tend to grant equity-linked compensation more often than firms with more non independent outside directors. Our results challenge the commonly accepted view of independent directors as safeguards of shareholder value, uncovering the relevance of non-independent outsiders for pay moderation and incentives.

Standard compensation for power cuts. Working group report

International Nuclear Information System (INIS)

2002-07-01

The Working Group was commissioned to draw up a proposal in the form of a Government Bill for provisions to be included in the Electricity Market Act on imposing an obligation on the distribution net operator to pay a standard compensation to the users of electricity for the event that they get no access to electricity. The Working Group should consider especially a model of standard compensation presented in the final report by Mr. Jarl Forsten, Deputy Director General of the Technical Research Centre of Finland VTT, published on 30 April 2002 that the amount of standard compensation should not depend on the reason for the power cut. The Working Group proposes that the Electricity Market Act should be amended by provisions providing that a distribution net operator shall pay to the user of electricity a standard compensation for power cuts lasting over 12 hours. The amount of compensation shall be based on the annual network service fee and a sliding scale of compensation related to the duration of the power cut shall be applied. The maximum compensation shall be paid when the power cut lasts more than five days. The maximum amount of individual compensations shall be fixed at EUR 700. The proposed provisions on standard compensation in the event of power cuts are aimed at amending the provisions in Chapter 6a of the Electricity Market Act on price reduction and compensation because of fault in the supply of electricity. The aim of the introduction of standard compensation for power cuts is to persuade distribution net operators to make an effort to minimize the time for power cuts. (orig.)

Lithium compensation of GaAs

International Nuclear Information System (INIS)

Alexiev, D.; Tavendale, A.J.

1988-08-01

Defects generated following Li diffusion into GaAs were studied by optical deep level transient spectroscopy (ODLTS) and deep level transient spectroscopy (DLTS). In an exploratory series of experiments, the effect of Li diffusion on existing trap spectra, defect generation and as a means for the compensation of GaAs was studied. The variables included diffusion temperature, initial trap spectra of GaAs and annealing periods. Detailed measurements of trap energies were made

Engineering Compensations in Web Service Environment

DEFF Research Database (Denmark)

Schäfer, Micahel; Dolog, Peter; Nejdl, Wolfgang

2007-01-01

Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure in such a......Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure...... in such an environment occurs, a compensation can be initiated to recover from the failure. However, current environments have only limited capabilities for compensations, and are usually based on backward recovery. In this paper, we introduce an engineering approach and an environment to deal with advanced...... compensations based on forward recovery principles. We extend the existing Web service transaction coordination architecture and infrastructure in order to support flexible compensation operations. A contract-based approach is being used, which allows the specification of permitted compensations at runtime. We...

Radiative and non-radiative relaxation of excitons in strain-compensated quantum dots

International Nuclear Information System (INIS)

Kujiraoka, M.; Ishi-Hayase, J.; Akahane, K.; Yamamoto, Y.; Ema, K.; Sasaki, M.

2008-01-01

We have investigated the population dynamics of excitons in strain-compensated InAs quantum dots (QDs) using a pump-probe technique under resonant excitation. Precise control of polarization directions of incident pulses enabled us to selectively estimate population lifetimes for two orthogonally polarized exciton ground states according to polarization selection rules. Measured decay times of the probe transmissions were highly dependent on the polarization directions of the exciton states. We found that the ratio of the decay times for the orthogonally polarized states is in quantitative agreement with the ratio of square of the transition dipole moments. This indicates that radiative recombination processes have a dominant effect on the population dynamics and that non-radiative and spin relaxations are negligible in our QDs. As a result, we can estimate the radiative lifetimes to be 1.0±0.1 and 1.7±0.2 ns for orthogonally polarized exciton ground states

Changing Conceptions of Employee Compensation

Science.gov (United States)

Dixon, Mark R.; Hayes, Linda J.

2004-01-01

This paper reviews and discusses many differing forms of incentive compensation systems that are being used in today's organizations. The review traces the roots of bonus compensation from individual piece-work plans through the adoption of organization-wide gain sharing plans to the growing recognition of open-book management. Reasons for the…

29 CFR 505.3 - Prevailing minimum compensation.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Prevailing minimum compensation. 505.3 Section 505.3 Labor... HUMANITIES § 505.3 Prevailing minimum compensation. (a)(1) In the absence of an alternative determination...)(2) of this section, the prevailing minimum compensation required to be paid under the Act to the...

A flexible and cost-effective compensation method for leveling using large-scale coordinate measuring machines and its application in aircraft digital assembly

Science.gov (United States)

Deng, Zhengping; Li, Shuanggao; Huang, Xiang

2018-06-01

In the assembly process of large-size aerospace products, the leveling and horizontal alignment of large components are essential prior to the installation of an inertial navigation system (INS) and the final quality inspection. In general, the inherent coordinate systems of large-scale coordinate measuring devices are not coincident with the geodetic horizontal system, and a dual-axis compensation system is commonly required for the measurement of difference in heights. These compensation systems are expensive and dedicated designs for different devices at present. Considering that a large-size assembly site usually needs more than one measuring device, a compensation approach which is versatile for different devices would be a more convenient and economic choice for manufacturers. In this paper, a flexible and cost-effective compensation method is proposed. Firstly, an auxiliary measuring device called a versatile compensation fixture (VCF) is designed, which mainly comprises reference points for coordinate transformation and a dual-axis inclinometer, and a kind of network tighten points (NTPs) are introduced and temporarily deployed in the large measuring space to further reduce transformation error. Secondly, the measuring principle of height difference is studied, based on coordinate transformation theory and trigonometry while considering the effects of earth curvature, and the coordinate transformation parameters are derived by least squares adjustment. Thirdly, the analytical solution of leveling uncertainty is analyzed, based on which the key parameters of the VCF and the proper deployment of NTPs are determined according to the leveling accuracy requirement. Furthermore, the proposed method is practically applied to the assembly of a large helicopter by developing an automatic leveling and alignment system. By measuring four NTPs, the leveling uncertainty (2σ) is reduced by 29.4% to about 0.12 mm, compared with that without NTPs.

Person-based differences in pay reactions: A compensation-activation theory and integrative conceptual review.

Science.gov (United States)

Fulmer, Ingrid Smithey; Shaw, Jason D

2018-06-07

Compensation research has focused traditionally on how pay design characteristics (e.g., pay level, individual or group incentives) relate to average employee outcomes and, in toto, on how these outcomes affect organizational performance. Recently, scholars have begun to pay more attention to how individuals vary in the strength of their reactions to pay. Empirical research in several disciplines examines how the interplay of pay systems and person-based characteristics (psychological individual differences, demographics, and relative performance or position in a group) relate to important work-related outcomes. We develop a compensation-activation theory that frames compensation design characteristics as workplace "situations" providing cues that activate individuals' corresponding fundamental social motives made salient due to chronic or transient person-based characteristics. Where activation occurs, stronger-than-average responses to the compensation "situation" are expected. Using the theory as a lens, we synthesize and reinterpret existing research on person-based reactions to pay characteristics, including sorting, incentive/motivational effects, and effects on collective pay system reactions and unit/organizational outcomes. We conclude with a research agenda aimed at refining compensation-activation theory and advancing the study of compensation as it affects individual and organizational outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Joint compensation scheme of polarization crosstalk, intersymbol interference, frequency offset, and phase noise based on cascaded Kalman filter

Science.gov (United States)

Zhang, Qun; Yang, Yanfu; Xiang, Qian; Zhou, Zhongqing; Yao, Yong

2018-02-01

A joint compensation scheme based on cascaded Kalman filter is proposed, which can implement polarization tracking, channel equalization, frequency offset, and phase noise compensation simultaneously. The experimental results show that the proposed algorithm can not only compensate multiple channel impairments simultaneously but also improve the polarization tracking capacity and accelerate the convergence speed. The scheme has up to eight times faster convergence speed compared with radius-directed equalizer (RDE) + Max-FFT (maximum fast Fourier transform) + BPS (blind phase search) and can track up polarization rotation 60 times and 15 times faster than that of RDE + Max-FFT + BPS and CMMA (cascaded multimodulus algorithm) + Max-FFT + BPS, respectively.

The Availability of Residential Real Estate Increasing by Means of State Compensation of Prices

Directory of Open Access Journals (Sweden)

Vitaly Viktorovich Ivanitskiy

2015-12-01

Full Text Available The article analyzes the influence of natural monopolies on the value of residential property, discusses the basic energy resources affecting it. Oil is defined as the main energy resource, its main brands, and their features are considered. The different authors’ perspectives of the impact of oil prices on the real estate prices are considered (“no effect”, “direct effect” and “indirect effect”. Schemes (models, clearly demonstrating the cause-and-effect relations of the impact of prices of the main energy resources on each other and on the value of residential property, are provided. The stability of relations between the prices of the major energy recourses (between each other as well as between each resource and real estate prices and residential property prices in the primary market are analyzed. The interval of “crisis” and “crisis-free” time is defined. The impact of the energy in “crisis” and “crisis-free” time is analyzed. The impact of oil prices on the residential property prices is proved through the cement as the main price-determining element in the construction. The introduction of the state target compensation allowing to increase the availability of residential property is proposed as one of the elements of a comprehensive solution of the “housing question”. The size of the state target compensation in absolute (in rubles and relative (% prices for residential real estate values is determined, taking into account the sufficient reproduction of the population, and restrictions on the right to use it are introduced. The total value of the state target compensation per total number of homebuyers is calculated, and its share in the expenditures of the consolidated budget and budgets of state extra-budgetary funds is determined. The realization of the state target compensation based on an average annual growth among the major countries of the world is grounded.

Analysis of emittance compensation and simulation results to photo-cathode RF gun

CERN Document Server

LiuShengGuang

2002-01-01

The emittance compensation technology will be used on the photo-cathode RF gun for Shanghai SDUV-FEL. The space charge force and its effect on electron beam transverse emittance in RF gun is studied, the principle of emittance compensation in phase-space is discussed. The authors have designed a compensation solenoid and calculated its magnetic field distribution. Its performance has been studied by the code PARMELA. A simulation result indicates that the normalized transverse RMS emittance for electron beam of 1.5 nC is 1.612 pi mm centre dot mrad, electron energy E = 5.71 MeV

Does injury compensation lead to worse health after whiplash? A systematic review.

Science.gov (United States)

Spearing, Natalie M; Connelly, Luke B; Gargett, Susan; Sterling, Michele

2012-06-01

One might expect that injury compensation would leave injured parties better off than they would otherwise have been, yet many believe that compensation does more harm than good. This study systematically reviews the evidence on this "compensation hypothesis" in relation to compensable whiplash injuries. PubMed, CINAHL, EMBASE, PEDro, PsycInfo, CCTR, Lexis, and EconLit were searched from the date of their inception to April 2010 to locate longitudinal studies, published in English, comparing the health outcomes of adults exposed/not exposed to compensation-related factors. Studies concerning serious neck injuries, using claimants only, or using proxy measures of health outcomes were excluded. Eleven studies were included. These examined the effect of lawyer involvement, litigation, claim submission, or previous claims on pain and other health outcomes. Among the 16 results reported were 9 statistically significant negative associations between compensation-related factors and health outcomes. Irrespective of the compensation-related factor involved and the health outcome measured, the quality of these studies was similar to studies that did not find a significant negative association: most took some measures to address selection bias, confounding, and measurement bias, and none resolved the potential for reverse causality bias that arises in the relationship between compensation-related factors and health. Unless ambiguous causal pathways are addressed, one cannot draw conclusions from statistical associations, regardless of their statistical significance and the extent of measures to address other sources of bias. Consequently, there is no clear evidence to support the idea that compensation and its related processes lead to worse health. Copyright © 2012 International Association for the Study of Pain. Published by Elsevier B.V. All rights reserved.

Temporal Scalability of Dynamic Volume Data using Mesh Compensated Wavelet Lifting.

Science.gov (United States)

Schnurrer, Wolfgang; Pallast, Niklas; Richter, Thomas; Kaup, Andre

2017-10-12

Due to their high resolution, dynamic medical 2D+t and 3D+t volumes from computed tomography (CT) and magnetic resonance tomography (MR) reach a size which makes them very unhandy for teleradiologic applications. A lossless scalable representation offers the advantage of a down-scaled version which can be used for orientation or previewing, while the remaining information for reconstructing the full resolution is transmitted on demand. The wavelet transform offers the desired scalability. A very high quality of the lowpass sub-band is crucial in order to use it as a down-scaled representation. We propose an approach based on compensated wavelet lifting for obtaining a scalable representation of dynamic CT and MR volumes with very high quality. The mesh compensation is feasible to model the displacement in dynamic volumes which is mainly given by expansion and contraction of tissue over time. To achieve this, we propose an optimized estimation of the mesh compensation parameters to optimally fit for dynamic volumes. Within the lifting structure, the inversion of the motion compensation is crucial in the update step. We propose to take this inversion directly into account during the estimation step and can improve the quality of the lowpass sub-band by 0.63 dB and 0.43 dB on average for our tested dynamic CT and MR volumes at the cost of an increase of the rate by 2.4% and 1.2% on average.

A Cenozoic record of the equatorial Pacific carbonate compensation depth.

Science.gov (United States)

Pälike, Heiko; Lyle, Mitchell W; Nishi, Hiroshi; Raffi, Isabella; Ridgwell, Andy; Gamage, Kusali; Klaus, Adam; Acton, Gary; Anderson, Louise; Backman, Jan; Baldauf, Jack; Beltran, Catherine; Bohaty, Steven M; Bown, Paul; Busch, William; Channell, Jim E T; Chun, Cecily O J; Delaney, Margaret; Dewangan, Pawan; Dunkley Jones, Tom; Edgar, Kirsty M; Evans, Helen; Fitch, Peter; Foster, Gavin L; Gussone, Nikolaus; Hasegawa, Hitoshi; Hathorne, Ed C; Hayashi, Hiroki; Herrle, Jens O; Holbourn, Ann; Hovan, Steve; Hyeong, Kiseong; Iijima, Koichi; Ito, Takashi; Kamikuri, Shin-ichi; Kimoto, Katsunori; Kuroda, Junichiro; Leon-Rodriguez, Lizette; Malinverno, Alberto; Moore, Ted C; Murphy, Brandon H; Murphy, Daniel P; Nakamura, Hideto; Ogane, Kaoru; Ohneiser, Christian; Richter, Carl; Robinson, Rebecca; Rohling, Eelco J; Romero, Oscar; Sawada, Ken; Scher, Howie; Schneider, Leah; Sluijs, Appy; Takata, Hiroyuki; Tian, Jun; Tsujimoto, Akira; Wade, Bridget S; Westerhold, Thomas; Wilkens, Roy; Williams, Trevor; Wilson, Paul A; Yamamoto, Yuhji; Yamamoto, Shinya; Yamazaki, Toshitsugu; Zeebe, Richard E

2012-08-30

Atmospheric carbon dioxide concentrations and climate are regulated on geological timescales by the balance between carbon input from volcanic and metamorphic outgassing and its removal by weathering feedbacks; these feedbacks involve the erosion of silicate rocks and organic-carbon-bearing rocks. The integrated effect of these processes is reflected in the calcium carbonate compensation depth, which is the oceanic depth at which calcium carbonate is dissolved. Here we present a carbonate accumulation record that covers the past 53 million years from a depth transect in the equatorial Pacific Ocean. The carbonate compensation depth tracks long-term ocean cooling, deepening from 3.0-3.5 kilometres during the early Cenozoic (approximately 55 million years ago) to 4.6 kilometres at present, consistent with an overall Cenozoic increase in weathering. We find large superimposed fluctuations in carbonate compensation depth during the middle and late Eocene. Using Earth system models, we identify changes in weathering and the mode of organic-carbon delivery as two key processes to explain these large-scale Eocene fluctuations of the carbonate compensation depth.

The effect of animal health compensation on 'positive' behaviours towards exotic disease reporting and implementing biosecurity: A review, a synthesis and a research agenda.

Science.gov (United States)

Barnes, Andrew Peter; Moxey, Andrew Paul; Vosough Ahmadi, Bouda; Borthwick, Fiona Ann

2015-11-01

With an increasing burden on public sector budgets, increased responsibility and cost sharing mechanisms for animal diseases are being considered. To achieve this, fiscal and non-fiscal intervention policies need to be designed such that they consistently promote positive disease risk management practices by animal keepers. This paper presents a review of the available evidence towards whether and how the level and type of funding mechanism affects change within biosecurity behaviours and the frequency of disease reporting. A Nuffield Health Ladder of Interventions approach is proposed as a way to frame the debate surrounding both current compensation mechanisms and how it is expected to change behaviour. Results of the review reveal a division between economic modelling approaches, which implicitly assume a causal link between payments and positive behaviours, and socio-geographic approaches which tend to ignore the influence of compensation mechanisms on influencing behaviours. Generally, economic studies suggest less than full compensation rates will encourage positive behaviours, but the non-economic literature indicate significant variation in response to compensation reflecting heterogeneity of livestock keepers in terms of their values, goals, risk attitudes, size of operation, animal species and production chain characteristics. This may be of encouragement to Western Governments seeking to shift cost burdens as it may induce greater targeting of non-fiscal mechanisms, or suggest more novel ways to augment current compensation mechanisms to both increase responsibility sharing and reduce this cost burden. This review suggests that a range of regulatory, fiscal and nudging policies are required to achieve socially optimal results with respect to positive behaviour change. However, the lack of directly available evidence which proves these causal links may hinder progress towards this optimal mixture of choice and non-choice based interventions. Copyright �

Enthalpy-entropy compensation: the role of solvation.

Science.gov (United States)

Dragan, Anatoliy I; Read, Christopher M; Crane-Robinson, Colyn

2017-05-01

Structural modifications to interacting systems frequently lead to changes in both the enthalpy (heat) and entropy of the process that compensate each other, so that the Gibbs free energy is little changed: a major barrier to the development of lead compounds in drug discovery. The conventional explanation for such enthalpy-entropy compensation (EEC) is that tighter contacts lead to a more negative enthalpy but increased molecular constraints, i.e., a compensating conformational entropy reduction. Changes in solvation can also contribute to EEC but this contribution is infrequently discussed. We review long-established and recent cases of EEC and conclude that the large fluctuations in enthalpy and entropy observed are too great to be a result of only conformational changes and must result, to a considerable degree, from variations in the amounts of water immobilized or released on forming complexes. Two systems exhibiting EEC show a correlation between calorimetric entropies and local mobilities, interpreted to mean conformational control of the binding entropy/free energy. However, a substantial contribution from solvation gives the same effect, as a consequence of a structural link between the amount of bound water and the protein flexibility. Only by assuming substantial changes in solvation-an intrinsically compensatory process-can a more complete understanding of EEC be obtained. Faced with such large, and compensating, changes in the enthalpies and entropies of binding, the best approach to engineering elevated affinities must be through the addition of ionic links, as they generate increased entropy without affecting the enthalpy.

39 CFR 3.2 - Compensation of Board.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Compensation of Board. 3.2 Section 3.2 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE BOARD OF GOVERNORS (ARTICLE III) § 3.2 Compensation of Board. Section 202(a)(1) of title 39 provides for the compensation of...

26 CFR 31.3231(e)-1 - Compensation.

Science.gov (United States)

2010-04-01

.... (a) Definition—(1) The term compensation has the same meaning as the term wages in section 3121(a... regarding the inclusion of fringe benefits in compensation, see § 31.3121(a)-1T. (6) Split-dollar life... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Compensation. 31.3231(e)-1 Section 31.3231(e)-1...

Executive Compensation and the Cost of Debt

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Li, Hao; Veld-Merkoulova, Yulia V.

2010-01-01

We examine how executive compensation affects the cost of debt financing. Analyzing CEO pay data from the UK, we find that debt-like and equity-like pay components have opposite effects on the cost of debt. An increase in defined benefit pensions is associated with lower bond yield spread, while an

Flexible Compensation of Voltage and Current Unbalance and Harmonics in Microgrids

Directory of Open Access Journals (Sweden)

Seyyed Yousef Mousazadeh Mousavi

2017-10-01

Full Text Available In recent years, the harmonics and unbalance problems endanger the voltage and current quality of power systems, due to increasing usage of nonlinear and unbalanced loads. Use of Distributed Generation (DG-interfacing inverters is proposed for voltage or current compensation. In this paper, a flexible control method is proposed to compensate voltage and current unbalance and harmonics using the distributed generation (DG-interfacing inverters. This method is applicable to both grid-connected and islanded Microgrids (MGs. In the proposed method, not only the proper control of active and reactive powers can be achieved, but also there is flexibility in compensating the voltage or current quality problems at DG terminals or Points of Common Coupling (PCCs. This control strategy consists of active and reactive power controllers and a voltage/current quality-improvement block. The controller is designed in a stationary (αβ frame. An extensive simulation study has been performed and the results demonstrate the effectiveness of the proposed control scheme. Depending on the compensation modes, the harmonics and unbalance compensation of DG output current, MG-injected current to the grid, as well as PCC and DG voltages, can be achieved in grid-connected operation of MG while in the islanded operation, and the PCC and DG voltages compensation can be obtained through the proposed control scheme.

Development of a pressurizer level compensator for use on N Reactor

International Nuclear Information System (INIS)

Bussell, J.H.

1985-07-01

The instrument described in this report has been developed to compensate the measured water level in the N Reactor pressurizer for temperature effects. N Reactor is a pressurized water nuclear reactor (PWR). The instrument is defined as a pressurizer level compensator (PLC). A pressurizer is used in a PWR to control the primary coolant pressure and provide a surge volume for primary coolant expansion and contraction. A means of compensating for water and steam density is required because of the wide range of pressure and temperature that result from different steady state and transient reactor power levels. The uncompensated level is determined by measurement of differential pressure between the top of the level measurement zone and the bottom of the level measurement zone. Temperature of the water in the pressurizer is the parameter that is used to determine the proper level compensation since water and steam density are primarily functions of temperature in this case. The PLC uses a microprocessor to calculate the compensated level from temperature and differential pressure measurements. This report includes a description of the design, development, and implementation of software and hardware that are in the PLC. 9 refs., 51 figs., 17 tabs

Directions in low-level radioactive-waste management. Incentives and compensation: providing resources for communities hosting low-level waste facilities

International Nuclear Information System (INIS)

1982-10-01

State responsibility for the management of low-level radioactive waste necessitates the selection of candidate locations for a disposal facility. Concern over potential impacts can be expected from segments of the citizenry neighboring a proposed site. A number of national organizations comprising state and local officials have recommended the use of incentives and compensation to help offset the negative local impacts. This document explores that concept. Discussion provides background information on potential local impacts from a low-level waste facility and considers the nature and types of incentives and compensation benefits that could be provided. The document then examines realistic options for planning and implementing the benefit program. This information is intended, primarily, to assist state officials - executive, legislative, and agency - in planning for and managing low-level waste disposal facilities

33 CFR 136.223 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS... allowable under paragraph (a) of this section must be reduced by— (1) All compensation made available to the... under § 136.235. Government Revenues ...

How Can Women Escape the Compensation Negotiation Dilemma? Relational Accounts Are One Answer

Science.gov (United States)

Bowles, Hannah Riley; Babcock, Linda

2013-01-01

Policy makers, academics, and media reports suggest that women could shrink the gender pay gap by negotiating more effectively for higher compensation. Yet women entering compensation negotiations face a dilemma: They have to weigh the benefits of negotiating against the social consequences of having negotiated. Research shows that women are…

A compound control strategy combining velocity compensation with ADRC of electro-hydraulic position servo control system.

Science.gov (United States)

Gao, Bingwei; Shao, Junpeng; Yang, Xiaodong

2014-11-01

In order to enhance the anti-jamming ability of electro-hydraulic position servo control system at the same time improve the control precision of the system, a compound control strategy that combines velocity compensation with Active Disturbance Rejection Controller (ADRC) is proposed, and the working principle of the compound control strategy is given. ADRC controller is designed, and the extended state observer is used for observing internal parameters uncertainties and external disturbances, so that the disturbances of the system are suppressed effectively. Velocity compensation controller is designed and the compensation model is derived to further improve the positioning accuracy of the system and to achieve the velocity compensation without disturbance. The compound control strategy is verified by the simulation and experiment respectively, and the simulation and experimental results show that the electro-hydraulic position servo control system with ADRC controller can effectively inhibit the external disturbances, the precise positioning control is realized after introducing the velocity compensation controller, and verify that the compound control strategy is effective. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Compensation of Disadvantages in University Examination Procedures

Directory of Open Access Journals (Sweden)

Ulrike Quapp

2016-08-01

Full Text Available Active social participation of disabled people is one of the major tasks of modern society. That also includes access to the academic community by higher education. Universities all over the world work hard to give handicapped students a chance to graduate. In this context, compensation of disadvantages in examination procedures is an important matter. But, also chronic illness may impair the student's examination performance. To ensure equal examination opportunities for all students, responsible university officials must be creative to find individual compensation solutions. The paper analyzes examination regulations at universities in different countries and offers solutions to compensate disabled and chronic ill students' disadvantages. It discusses the necessity of compensation for different types of disability and chronic illness. Finally, an overview of current German case law and solutions for compensation problems are provided.

Identification of amino acid substitutions with compensational effects in the attachment protein of canine distemper virus.

Science.gov (United States)

Sattler, Ursula; Khosravi, Mojtaba; Avila, Mislay; Pilo, Paola; Langedijk, Johannes P; Ader-Ebert, Nadine; Alves, Lisa A; Plattet, Philippe; Origgi, Francesco C

2014-07-01

The hemagglutinin (H) gene of canine distemper virus (CDV) encodes the receptor-binding protein. This protein, together with the fusion (F) protein, is pivotal for infectivity since it contributes to the fusion of the viral envelope with the host cell membrane. Of the two receptors currently known for CDV (nectin-4 and the signaling lymphocyte activation molecule [SLAM]), SLAM is considered the most relevant for host susceptibility. To investigate how evolution might have impacted the host-CDV interaction, we examined the functional properties of a series of missense single nucleotide polymorphisms (SNPs) naturally accumulating within the H-gene sequences during the transition between two distinct but related strains. The two strains, a wild-type strain and a consensus strain, were part of a single continental outbreak in European wildlife and occurred in distinct geographical areas 2 years apart. The deduced amino acid sequence of the two H genes differed at 5 residues. A panel of mutants carrying all the combinations of the SNPs was obtained by site-directed mutagenesis. The selected mutant, wild type, and consensus H proteins were functionally evaluated according to their surface expression, SLAM binding, fusion protein interaction, and cell fusion efficiencies. The results highlight that the most detrimental functional effects are associated with specific sets of SNPs. Strikingly, an efficient compensational system driven by additional SNPs appears to come into play, virtually neutralizing the negative functional effects. This system seems to contribute to the maintenance of the tightly regulated function of the H-gene-encoded attachment protein. Importance: To investigate how evolution might have impacted the host-canine distemper virus (CDV) interaction, we examined the functional properties of naturally occurring single nucleotide polymorphisms (SNPs) in the hemagglutinin gene of two related but distinct strains of CDV. The hemagglutinin gene encodes the

The Report on Part-Time Faculty Compensation and Salary Survey, House Bill 384

Science.gov (United States)

New Mexico Higher Education Department, 2007

2007-01-01

In the 2007 Legislative Session, House Bill 384 (HB 384) directed the New Mexico Higher Education Department to produce an Annual Accountability Report in collaboration with each public postsecondary educational institution in the state of New Mexico. The report contains information pertaining to: (1) faculty compensation and benefits practices;…

Compensator design for improved counterbalancing in high speed atomic force microscopy

Science.gov (United States)

Bozchalooi, I. S.; Youcef-Toumi, K.; Burns, D. J.; Fantner, G. E.

2011-11-01

High speed atomic force microscopy can provide the possibility of many new scientific observations and applications ranging from nano-manufacturing to the study of biological processes. However, the limited imaging speed has been an imperative drawback of the atomic force microscopes. One of the main reasons behind this limitation is the excitation of the AFM dynamics at high scan speeds, severely undermining the reliability of the acquired images. In this research, we propose a piezo based, feedforward controlled, counter actuation mechanism to compensate for the excited out-of-plane scanner dynamics. For this purpose, the AFM controller output is properly filtered via a linear compensator and then applied to a counter actuating piezo. An effective algorithm for estimating the compensator parameters is developed. The information required for compensator design is extracted from the cantilever deflection signal, hence eliminating the need for any additional sensors. The proposed approach is implemented and experimentally evaluated on the dynamic response of a custom made AFM. It is further assessed by comparing the imaging performance of the AFM with and without the application of the proposed technique and in comparison with the conventional counterbalancing methodology. The experimental results substantiate the effectiveness of the method in significantly improving the imaging performance of AFM at high scan speeds.

Quantitative Evaluation of Range Degradation According to the Gradient of the Compensator in Passive Scattering Proton Therapy

Energy Technology Data Exchange (ETDEWEB)

Shin, Wook Geun; Min, Chul Hee [Radiation Convergence Engineering, Yonsei University, Seoul (Korea, Republic of); Kim, Chan Kyu; Kim, Hak Soo; Jeong, Jong Hwi; Lee, Se Byeong [Proton Therapy Center, National Center Center, Seoul (Korea, Republic of)

2017-04-15

The Bragg peak enables proton therapy to deliver a high conformal target dose without exit dose. The passive scattering proton therapy employees patient-specific aperture and range compensator to shape the lateral and distal beam, and to deliver conformal dose to the target volume. The inaccurate dose calculation could cause underdose in the target volume and overdose in the normal tissues. The purpose of this study is to quantitatively evaluate the range degradation due to the slope of the range compensator using TOPAS Monte Carlo (MC) tool. The current study quantitatively evaluates the scattering effect due to the compensator slope with MC method. Our results show that not only patient geometry but also range compensator significantly contributes to the dose degradation. The current study quantitatively evaluates the scattering effect due to the compensator slope with MC method. Our results show that not only patient geometry but also range compensator significantly contributes to the dose degradation.

“Jump Start and Gain” Model for Dosage Compensation in Drosophila Based on Direct Sequencing of Nascent Transcripts

Directory of Open Access Journals (Sweden)

Francesco Ferrari

2013-11-01

Full Text Available Dosage compensation in Drosophila is mediated by the MSL complex, which increases male X-linked gene expression approximately 2-fold. The MSL complex preferentially binds the bodies of active genes on the male X, depositing H4K16ac with a 3′ bias. Two models have been proposed for the influence of the MSL complex on transcription: one based on promoter recruitment of RNA polymerase II (Pol II, and a second featuring enhanced transcriptional elongation. Here, we utilize nascent RNA sequencing to document dosage compensation during transcriptional elongation. We also compare X and autosomes from published data on paused and elongating polymerase in order to assess the role of Pol II recruitment. Our results support a model for differentially regulated elongation, starting with release from 5′ pausing and increasing through X-linked gene bodies. Our results highlight facilitated transcriptional elongation as a key mechanism for the coordinated regulation of a diverse set of genes.

Testing Long-Range Beam-Beam Compensation for the LHC Luminosity Upgrade

CERN Document Server

Rijoff, T L

2012-01-01

The performance of the Large Hadron Collider (LHC) at CERN and its minimum crossing angle are limited by the effect of long-range beam-beam collisions. A wire compensators can mitigate part of the long-range effects and may allow for smaller crossing angles, or higher beam intensity. A prototype long-range wire compensator could be installed in the LHC by 2014/15. Since the originally reserved position for such a wire compensator is not available for this first step, we explore other possible options. Our investigations consider various longitudinal and transverse locations, different wire shapes, different optics configurations and several crossing angles between the two colliding beams. Simulations are carried out with the weak-strong code BBtrack. New postprocessing tools are introduced to analyse tune footprints and particle stability. In particular, a new method for the Lyapunov coefficient calculation is implemented. Submitted as "Tesi di laurea" at the University of Milano, 2012.

Compensation for nuclear damage in the OECD member countries

International Nuclear Information System (INIS)

1977-01-01

The study aims to describe briefly the main features of the system for compensation of nuclear damage in OECD Member Countries, emphasising the practical arrangements for compensating such damage, with illustrations drawn from various national legal provisions applicable to such cases. The study indicates and compares legislative provisions which are specifically nuclear, without going into the substantive and procedural rules of the general law, reference to which frequently occurs in enactments relating to nuclear third party liability. The references to national nuclear legislation illustrate the manner in which effect has been given to international Conventions. (Auth.) [fr

The effects of betatron phase advances on beam-beam and its compensation in RHIC

Energy Technology Data Exchange (ETDEWEB)

Luo, Y.; Fischer, W.; Gu, X.; Tepikian, S.; Trbojevic, D.

2011-03-28

In this article we perform simulation studies to investigate the effects of betatron phase advances between the beam-beam interaction points on half-integer resonance driving term, second order chromaticty and dynamic aperture in RHIC. The betatron phase advances are adjusted with artificial matrices inserted in the middle of arcs. The lattices for the 2011 RHIC polarized proton (p-p) run and 2010 RHIC Au-Au runs are used in this study. We also scan the betatron phase advances between IP8 and the electron lens for the proposed Blue ring lattice with head-on beam-beam compensation.

Global compensation of long-range beam-beam effects with octupole magnets: dynamic aperture simulations for the HL-LHC case and possible usage in LHC and FCC.

CERN Document Server

Barranco Garcia, Javier; CERN. Geneva. ATS Department

2017-01-01

The Large Hadron Collider has shown with various experimental verifications that one of the main limitations to the collider performance and to a possible upgrade can come from the long-range beam-beam effects which will define the operational parameters (intensities and emittances) and machine set-up (crossing angles and the minimum beta function at the interaction points). The High Luminosity project aims at very high intensities and will therefore need much larger separations to keep the long range effects weak. In the past several studies of possible active compensators have been carried out and experimental studies are planned to explore such schemes in the LHC. In this note we show the feasibility of using octupole magnets to compensate the effects of long range beam-beam interactions by use of dynamical aperture simulations. A prove of principle of such a compensation scheme is shown for the HL-LHC optics. Preliminary studies for the LHC optics ATS and standard are also presented pointing to the import...

[Effect of charge compensation on emission spectrum of Sr2SiO4 : Dy3+ phosphor].

Science.gov (United States)

Li, Pan-Lai; Wang, Zhi-Jun; Yang, Zhi-Ping; Guo, Qing-Lin

2009-01-01

The Sr2SiO4 : Dy3+ phosphor was synthesized by the high temperature solid-state reaction method in air. Dy2O3 (99.9%), SiO2 (99.9%), SrCO3 (99.9%), Li2CO3 (99.9%), Na2CO3 (99.9%) and K2CO3 (99.9%) were used as starting materials, and the Dy3+ doping concentration was 2 mol%. The emission spectrum was measured by a SPEX1404 spectrophotometer, and all the characterization of the phosphors was conducted at room temperature. The emission spectrum of Sr2 SiO4 : Dy3+ phosphor showed several bands centered at 486, 575 and 665 nm under the 365 nm excitation. The effect of Li+, Na+ and K+ on the emission spectra of Sr2SiO4 : Dy3+ phosphor was studied. The results show that the location of the emission spectrum of Sr2SiO4 : Dy3+ phosphor was not influenced by Li+, Na+ and K+. However, the emission spectrum intensity was greatly influenced by Li+, Na+ and K+, and the evolvement trend was monotone with different charge compensation, i. e. the emission spectrum intensity of Sr2SiO4 : Dy3+ phosphor firstly increased with increasing Li+ concentration, then decreased. However the charge compensation concentration corresponding to the maximum emission intensity was different with different charge compensation, and the concentration is 4, 3 and 3 mol% corresponding to Li+, Na+ and K+, respectively. And the theoretical reason for the above results was analyzed.

Dose compensation of the total body irradiation therapy

International Nuclear Information System (INIS)

Lin, J.-P.; Chu, T.-C.; Liu, M.-T.

2001-01-01

The aim of the study is to improve dose uniformity in the body by the compensator-rice and to decrease the dose to the lung by the partial lung block. Rando phantom supine was set up to treat bilateral fields with a 15 MV linear accelerator at 415 cm treatment distance. The experimental procedure included three parts. The first part was the bilateral irradiation without rice compensator, and the second part was with rice compensator. In the third part, rice compensator and partial lung block were both used. The results of thermoluminescent dosimeters measurements indicated that without rice compensator the dose was non-uniform. Contrarily, the average dose homogeneity with rice compensator was measured within ±5%, except for the thorax region. Partial lung block can reduce the dose which the lung received. This is a simple method to improve the dose homogeneity and to reduce the lung dose received. The compensator-rice is cheap, and acrylic boxes are easy to obtain. Therefore, this technique is suitable for more studies

RTtxGap: An android radiobiological tool for compensation of radiotherapy treatment interruption

International Nuclear Information System (INIS)

Yusoff, A L; Mohamad, M; Bhavaraju, V M K; Idris, N R Nik; Abdullah, R

2016-01-01

Treatment interruption is not uncommon in radiotherapy. Common reasons for treatment interruption include machine breakdown, holidays and patient severe radiation reactions. Here RTtxGap, an Android application to assist calculations of compensation for treatment gap, is reported. It uses linear quadratic (LQ) model to calculate the biological effective dose (BED) that is used to solve for treatment gap compensations. Solutions are calculated using BED equation, with consideration for tissue proliferation. The accuracy of results has been verified using LQL Equiv software to be accurate within 1%. Five treatment interruption examples were used to illustrate the capability of the software to calculate the treatment compensation schedules. Solving these examples also illustrates the general consensus regarding compensating for unscheduled treatment interruptions, which ultimately involves balancing the BEDs of tumour and organ at risk. In addition to compensation for treatment gap, RTtxGap can also be used to calculate equivalent total dose in 2-Gy fraction (EQD2), to modify treatment schedule and to calculate alternative dose prescriptions having the same isoeffect. (paper)

Aeromagnetic Compensation Algorithm Based on Principal Component Analysis

Directory of Open Access Journals (Sweden)

Peilin Wu

2018-01-01

Full Text Available Aeromagnetic exploration is an important exploration method in geophysics. The data is typically measured by optically pumped magnetometer mounted on an aircraft. But any aircraft produces significant levels of magnetic interference. Therefore, aeromagnetic compensation is important in aeromagnetic exploration. However, multicollinearity of the aeromagnetic compensation model degrades the performance of the compensation. To address this issue, a novel aeromagnetic compensation method based on principal component analysis is proposed. Using the algorithm, the correlation in the feature matrix is eliminated and the principal components are using to construct the hyperplane to compensate the platform-generated magnetic fields. The algorithm was tested using a helicopter, and the obtained improvement ratio is 9.86. The compensated quality is almost the same or slightly better than the ridge regression. The validity of the proposed method was experimentally demonstrated.

Secondary control for voltage unbalance compensation in an islanded microgrid

DEFF Research Database (Denmark)

Savaghebi, Mehdi; Guerrero, Josep M.; Jalilian, Alireza

2011-01-01

In this paper, the concept of secondary control is applied for voltage unbalance compensation in an islanded microgrid. The aim of the proposed control approach is to enhance the voltage quality at the point of common coupling (PCC). Unbalance compensation is achieved by proper control...... of distributed generators (DGs). The DGs control structure mainly consists of active and reactive power controllers, virtual impedance loop and voltage and current proportional-resonant controllers. Simulation results are presented for different cases. The results show the effectiveness of the proposed approach...

No-fault vaccine insurance: lessons from the National Vaccine Injury Compensation Program.

Science.gov (United States)

Ridgway, D

1999-02-01

During the first eight years of the National Vaccine Injury Compensation Program (NVICP), 786 contested claims were resolved through published judicial opinions. The likelihood of compensation dependent in part on the closeness of the match between the described injury and a specified list of acknowledged untoward vaccine side effects. In addition, the chances of applicant success were influenced by the applicant's choice of attorney and expert witnesses, by the assignment of the Special Master to decide the case, and increasingly over time, by the applicant's ability to comply with procedural requirements. The majority of contested claims arose from pertussis immunizations. For pertussis claims, the goal of insulating manufacturers from product liability suits has been achieved by granting compensation to applicants whose injuries are not scientifically recognized effects of the vaccine. In spite of (or because of) this jarring contradiction between the legal and medical understanding of causation, vaccine availability and childhood immunization rates improved during the early years of the plan. The apparent success of the program may encourage the substitution of no-fault compensation plans for tort-based consumer protection for other products, both medical and nonmedical.

Caloric compensation for sugar-sweetened beverages in meals: A population-based study in Brazil.

Science.gov (United States)

Gombi-Vaca, Maria Fernanda; Sichieri, Rosely; Verly, Eliseu

2016-03-01

Sugar-sweetened beverage (SSB) consumption can cause positive energy balance, therefore leading to weight gain. A plausible biological mechanism to explain this association is through weak caloric compensation for liquid calories. However, there is an ongoing debate surrounding SSB calorie compensation. The body of evidence comes from a diversity of study designs and highly controlled settings assessing food and beverage intake. Our study aimed to test for caloric compensation of SSB in the free-living setting of daily meals. We analyzed two food records of participants (age 10 years or older) from the 2008-2009 National Dietary Survey (Brazil, N = 34,003). We used multilevel analyses to estimate the within-subject effects of SSB on food intake. Sugar-sweetened beverage calories were not compensated for when comparing daily energy intake over two days for each individual. When comparing meals, we found 42% of caloric compensation for breakfast, no caloric compensation for lunch and zero to 22% of caloric compensation for dinner, differing by household per capita income. In conclusion, SSB consumption contributed to higher energy intake due to weak caloric compensation. Discouraging the intake of SSB especially during lunch and dinner may help reduce excessive energy intake and lead to better weight management. Copyright © 2015 Elsevier Ltd. All rights reserved.

Compensation phenomena of a mixed spin-2 and spin-12 Heisenberg ferrimagnetic model: Green function study

International Nuclear Information System (INIS)

Li Jun; Wei Guozhu; Du An

2005-01-01

The compensation and critical behaviors of a mixed spin-2 and spin-12 Heisenberg ferrimagnetic system on a square lattice are investigated theoretically by the two-time Green's function technique, which takes into account the quantum nature of Heisenberg spins. The model can be relevant for understanding the magnetic behavior of the new class of organometallic ferromagnetic materials that exhibit spontaneous magnetic properties at room temperature. We carry out the calculation of the sublattice magnetizations and the spin-wave spectra of the ground state. In particular, we have studied the effects of the nearest, next-nearest-neighbor interactions, the crystal field and the external magnetic field on the compensation temperature and the critical temperature. When only the nearest-neighbor interactions and the crystal field are included, no compensation temperature exists; when the next-nearest-neighbor interaction between spin-12 is taken into account and exceeds a minimum value, a compensation point appears and it is basically unchanged for other parameters in Hamiltonian fixed. The next-nearest-neighbor interactions between spin-2 and the external magnetic field have the effects of changing the compensation temperature and there is a narrow range of parameters of the Hamiltonian for which the model has the compensation temperatures and compensation temperature exists only for a small value of them

Improving dose homogeneity in routine head and neck radiotherapy with custom 3-D compensation

International Nuclear Information System (INIS)

Harari, P.M.; Sharda, N.N.; Brock, L.K.; Paliwal, B.R.

1998-01-01

Background and purpose: Anatomic contour irregularity and tissue inhomogeneity can lead to significant radiation dose variation across the complex treatment volumes found in the head and neck (HandN) region. This dose inhomogeneity can routinely create focal hot or cold spots of 10-20% despite beam shaping with blocks or beam modification with wedges. Since 1992, we have implemented the routine use of 3-D custom tissue compensators fabricated directly from CT scan contour data obtained in the treatment position in order to improve dose uniformity in patients with tumors of the HandN. Materials and methods: Between July 1992 and January 1997, 160 patients receiving comprehensive HandN radiotherapy had 3-D custom compensators fabricated for their treatment course. Detailed dosimetric records have been analyzed for 30 cases. Dose uniformity across the treatment volume and clinically relevant maximum doses to selected anatomic sub-sites were examined with custom-compensated, uncompensated and optimally-wedged plans. Results: The use of 3-D custom compensators resulted in an average reduction of dose variance across the treatment volume from 19±4% for the uncompensated plans to 5±2% with the use of 3-D compensators. Optimally-wedged plans were variable, but on average a 10±3% dose variance was noted. For comprehensive HandN treatment which encompassed the larynx within the primary field design, the peak doses delivered were reduced by 5-15% with 3-D custom compensation as compared to optimal wedging. Conclusions: The use of 3-D custom tissue compensation can improve dose homogeneity within the treatment volume for HandN cancer patients. Maximum doses to clinically important structures which often receive greater than 105-110% of the prescribed dose are routinely reduced with the use of 3-D custom compensators. Improved dose uniformity across the treatment volume can reduce normal tissue complication profiles and potentially allow for delivery of higher total doses in

Study on a Mechanical Semi-Active Heave Compensation System of Drill String for Use on Floating Drilling Platform

Science.gov (United States)

Liu, Qingyou; Tang, Yang; Huang, Chongjun; Xie, Chong

2015-01-01

There are some disadvantages for existing heave compensation systems of drill string used for the Floating Drilling Platform (FDP), including high energy consumption, large and complex structure, and expensive manufacturing and maintenance costs. In view of the above, we present a streamlined mechanical semi-active heave compensation system (MSAHC) in this study. This system consists of active compensation part with the pinion and rack and passive compensation part. In order to evaluate system performance of the MSAHC, we establish its simulation model with AMEsim software. In the process of simulation, displacement of rotary hook and energy consumption is regarded as performance parameters of the system. And the change rule of two performance parameters are analyzed by changing these design parameters including gear radius of the pinion and rack, scale coefficient of PID, rotary hook load, heave height and heave period of the FDP, and accumulator volume. Then, based on the simulation results of the MSAHC system performance, we have selected out a best set of design parameters from them. Moreover, the feasibility of the design scheme of the MSAHC is effectively verified by comparison with the existing three heave compensation system. The result shows that the energy consumption of the MSAHC is lower than the active heave compensation system (AHC) and the semi-active heave compensation system (SAHC) when achieving a same compensation effect as well as the accumulator volume of MSAHC is half of the passive heave compensation system (PHC). Therefore, the new designed MSAHC not only ensure compensation effect but also lower energy consumption, and its structure is simplified by adopting the simple mechanical structure to decrease manufacturing cost, maintenance cost and floor space. PMID:26186620

Two-stage open-loop velocity compensating method applied to multi-mass elastic transmission system

Directory of Open Access Journals (Sweden)

Zhang Deli

2014-02-01

Full Text Available In this paper, a novel vibration-suppression open-loop control method for multi-mass system is proposed, which uses two-stage velocity compensating algorithm and fuzzy I + P controller. This compensating method is based on model-based control theory in order to provide a damping effect on the system mechanical part. The mathematical model of multi-mass system is built and reduced to estimate the velocities of masses. The velocity difference between adjacent masses is calculated dynamically. A 3-mass system is regarded as the composition of two 2-mass systems in order to realize the two-stage compensating algorithm. Instead of using a typical PI controller in the velocity compensating loop, a fuzzy I + P controller is designed and its input variables are decided according to their impact on the system, which is different from the conventional fuzzy PID controller designing rules. Simulations and experimental results show that the proposed velocity compensating method is effective in suppressing vibration on a 3-mass system and it has a better performance when the designed fuzzy I + P controller is utilized in the control system.

The effects of performance measurement and compensation on motivation : an empirical study

NARCIS (Netherlands)

van Herpen, M.; van Praag, M.; Cools, K.

2005-01-01

This paper analyzes empirically the relationship between pay and performance. Economic and psychological theories predict that the design and implementation of a performance measurement and compensation system affect the motivation of employees. Our survey results demonstrate a positive relationship

The effects of performance measurement and compensation on motivation : An empirical study

NARCIS (Netherlands)

Van Herpen, M; Van Praag, M; Cools, K

This paper analyzes empirically the relationship between pay and performance. Economic and psychological theories predict that the design and implementation of a performance measurement and compensation system affect the motivation of employees. Our survey results demonstrate a positive relationship

Influence of Gravity Compensation on Muscle Activation Patterns During Different Temporal Phases of Arm Movements of Stroke Patients

NARCIS (Netherlands)

Prange, Grada Berendina; Jannink, M.J.A.; Stienen, Arno; van der Kooij, Herman; IJzerman, Maarten Joost; Hermens, Hermanus J.

2009-01-01

Background. Arm support to help compensate for the effects of gravity may improve functional use of the shoulder and elbow during therapy after stroke, but gravity compensation may alter motor control. Objective. To obtain quantitative information on how gravity compensation influences muscle

Dynamic Viscosity and Compensation Effect in Hydrocarbon Media with a High Content of Resins and Paraffins

Science.gov (United States)

Boitsova, A. A.; Kondrasheva, N. K.; Dolomatov, M. Yu.

2017-11-01

Linear dependences have been obtained for multicomponent hydrocarbon media (oils and high-boiling fractions), which relate the preexponent and the activation energy of viscous flow in the Arrhenius equation. A distinctive feature of the established kinetic compensation effect is it existing before and after the phase-transition temperature. The obtained results have been confirmed by statistical data and make it possible to predict the dynamic viscosity of multicomponent hydrocarbon systems, such as oil and high-boiling fractions.

Radiobiological compensation: A case study of uterine cervix cancer with concurrent chemotherapy

Energy Technology Data Exchange (ETDEWEB)

Herrera, Higmar; Yanez, Elvia; Lopez, Jesus [Centro Estatal de Cancerologia de Durango, Victoria de Durango, Durango (Mexico); ISSSTE General Hospital Dr. Santiago Ramon y Cajal, Victoria de Durango, Durango (Mexico)

2012-10-23

The case of a patient diagnosed with uterine cervix cancer is presented as an example of the clinical application of the radiobiological compensation method implemented at Centro Estatal de Cancerologia de Durango. Radiotherapy treatment was initially modified to compensate for the chemotherapy component and, as medical complications arose during treatment delivery resulting in an 18 days gap, new compensation followed. All physical and radiobiological assumptions to calculate the Biologically Effective Dose in the external beam and brachytherapy parts of the treatment are presented. Good local control of the tumor was achieved, the theoretical tolerance limits for the organs at risk were not surpassed and the patient manifested no extensive morbidity.

Compensating Unknown Time-Varying Delay in Opto-Electronic Platform Tracking Servo System

Directory of Open Access Journals (Sweden)

Ruihong Xie

2017-05-01

Full Text Available This paper investigates the problem of compensating miss-distance delay in opto-electronic platform tracking servo system. According to the characteristic of LOS (light-of-sight motion, we setup the Markovian process model and compensate this unknown time-varying delay by feed-forward forecasting controller based on robust H∞ control. Finally, simulation based on double closed-loop PI (Proportion Integration control system indicates that the proposed method is effective for compensating unknown time-varying delay. Tracking experiments on the opto-electronic platform indicate that RMS (root-mean-square error is 1.253 mrad when tracking 10° 0.2 Hz signal.

33 CFR 136.211 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.211 Compensation... that amount required to accomplish the activities for which the claim was paid. Real or Personal...

X chromosome dosage compensation via enhanced transcriptional elongation in Drosophila.

Science.gov (United States)

Larschan, Erica; Bishop, Eric P; Kharchenko, Peter V; Core, Leighton J; Lis, John T; Park, Peter J; Kuroda, Mitzi I

2011-03-03

The evolution of sex chromosomes has resulted in numerous species in which females inherit two X chromosomes but males have a single X, thus requiring dosage compensation. MSL (Male-specific lethal) complex increases transcription on the single X chromosome of Drosophila males to equalize expression of X-linked genes between the sexes. The biochemical mechanisms used for dosage compensation must function over a wide dynamic range of transcription levels and differential expression patterns. It has been proposed that the MSL complex regulates transcriptional elongation to control dosage compensation, a model subsequently supported by mapping of the MSL complex and MSL-dependent histone 4 lysine 16 acetylation to the bodies of X-linked genes in males, with a bias towards 3' ends. However, experimental analysis of MSL function at the mechanistic level has been challenging owing to the small magnitude of the chromosome-wide effect and the lack of an in vitro system for biochemical analysis. Here we use global run-on sequencing (GRO-seq) to examine the specific effect of the MSL complex on RNA Polymerase II (RNAP II) on a genome-wide level. Results indicate that the MSL complex enhances transcription by facilitating the progression of RNAP II across the bodies of active X-linked genes. Improving transcriptional output downstream of typical gene-specific controls may explain how dosage compensation can be imposed on the diverse set of genes along an entire chromosome.

Installation of the sag compensator for HANARO

International Nuclear Information System (INIS)

Kim, Hyungkyoo; Jung, Hoansung; Lim, Incheol; Ahn, Gukhoon

2008-01-01

Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30 MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extent of sags occur. HANARO has the reactor regulation system(RRS) and reactor protection system(RPS). HANARO is designed so as to be tripped automatically by insertion of control absorber rods(CAR) and shut-off rods(SOR). When voltage sag or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator on the power supply for CARs and SORs so as to prevent an unwanted trip. We undertook voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator. (author)

Installation of the sag compensator for HANARO

International Nuclear Information System (INIS)

Kim, H. K.; Jung, H. S.; Ahn, G. H.; Lim, I. C.

2008-01-01

Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extents of sags occur. HANARO has the reactor regulation system (RRS) and reactor protection system (RPS). HANARO is designed so as to tripped automatically by insertion of control absorber rods (CAR) and shut-off rods (SOR). When voltage or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator on the power supply for CARs and SORs so as to prevent an unwanted trip. We undertook voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator

A Model of Gravity Vector Measurement Noise for Estimating Accelerometer Bias in Gravity Disturbance Compensation.

Science.gov (United States)

Tie, Junbo; Cao, Juliang; Chang, Lubing; Cai, Shaokun; Wu, Meiping; Lian, Junxiang

2018-03-16

Compensation of gravity disturbance can improve the precision of inertial navigation, but the effect of compensation will decrease due to the accelerometer bias, and estimation of the accelerometer bias is a crucial issue in gravity disturbance compensation. This paper first investigates the effect of accelerometer bias on gravity disturbance compensation, and the situation in which the accelerometer bias should be estimated is established. The accelerometer bias is estimated from the gravity vector measurement, and a model of measurement noise in gravity vector measurement is built. Based on this model, accelerometer bias is separated from the gravity vector measurement error by the method of least squares. Horizontal gravity disturbances are calculated through EGM2008 spherical harmonic model to build the simulation scene, and the simulation results indicate that precise estimations of the accelerometer bias can be obtained with the proposed method.

A Model of Gravity Vector Measurement Noise for Estimating Accelerometer Bias in Gravity Disturbance Compensation

Science.gov (United States)

Cao, Juliang; Cai, Shaokun; Wu, Meiping; Lian, Junxiang

2018-01-01

Compensation of gravity disturbance can improve the precision of inertial navigation, but the effect of compensation will decrease due to the accelerometer bias, and estimation of the accelerometer bias is a crucial issue in gravity disturbance compensation. This paper first investigates the effect of accelerometer bias on gravity disturbance compensation, and the situation in which the accelerometer bias should be estimated is established. The accelerometer bias is estimated from the gravity vector measurement, and a model of measurement noise in gravity vector measurement is built. Based on this model, accelerometer bias is separated from the gravity vector measurement error by the method of least squares. Horizontal gravity disturbances are calculated through EGM2008 spherical harmonic model to build the simulation scene, and the simulation results indicate that precise estimations of the accelerometer bias can be obtained with the proposed method. PMID:29547552

Crime victims‘ right to compensation

Directory of Open Access Journals (Sweden)

Mrvić-Petrović Nataša

2012-01-01

Full Text Available This paper analyzes the most important documents of the United Nations, Council of Europe and the European Union relating to rights to damage compensation (restitution from offender and state compensation. The analysis shows that there is a gradual move from the concept of exercising the rights of victims in favor of a solidaristic model that takes less into account the rights of victims, and more the need to satisfy their legitimate interests. The economic crisis that is undermining the foundations of the welfare state could jeopardize the realization of this concept, especially in those European countries where the criminal justice system focuses solely on the offender, as is the case in Serbia. In such circumstances, regulation which protects the right to compensation, other rights and interests of victims, shall apply only to the extent that serves crime prevention. So it happens that in spite of a suitable normative framework and developments regarding the protection of victims of domestic violence and trafficking, the right to compensation and other rights of the victims do not actually get actualized in practice. In order to overcome this, a systemic reform to the criminal justice system should be undertaken with the aim to redirect the system towards the victim of the offense. Within these reforms a public fund for compensation of the victims of violence should be established and the process of mediation between the victim and the offender with the goal to make a settlement should be regulated, because these mechanisms do not exist in Serbia.

Effect of Principal Managerial Leadership and Compensation towards Physics Teacher Performance in Senior High School in Baguala District-Ambon

Science.gov (United States)

Wenno, Izaak Hendrik

2017-01-01

The performance of teachers is an important factor that must be considered in efforts to improve the quality of education. Teacher's performance is affected by many factors. Factors that affect the performance of teachers are principals' managerial leadership and compensation. The purpose of this study was to determine the effect of principals'…

20 CFR 25.101 - How is compensation for death paid?

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false How is compensation for death paid? 25.101... EMPLOYEES' COMPENSATION ACT COMPENSATION FOR DISABILITY AND DEATH OF NONCITIZEN FEDERAL EMPLOYEES OUTSIDE THE UNITED STATES The Special Schedule of Compensation § 25.101 How is compensation for death paid? If...

Combining of Direct Search and Signal-to-Noise Ratio for economic dispatch optimization

International Nuclear Information System (INIS)

Lin, Whei-Min; Gow, Hong-Jey; Tsai, Ming-Tang

2011-01-01

This paper integrated the ideas of Direct Search and Signal-to-Noise Ratio (SNR) to develop a Novel Direct Search (NDS) method for solving the non-convex economic dispatch problems. NDS consists of three stages: Direct Search (DS), Global SNR (GSNR) and Marginal Compensation (MC) stages. DS provides a basic solution. GSNR searches the point with optimization strategy. MC fulfills the power balance requirement. With NDS, the infinite solution space becomes finite. Furthermore, a same optimum solution can be repeatedly reached. Effectiveness of NDS is demonstrated with three examples and the solutions were compared with previously published results. Test results show that the proposed method is simple, robust, and more effective than many other previously developed algorithms.

45 CFR 302.65 - Withholding of unemployment compensation.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Withholding of unemployment compensation. 302.65... HUMAN SERVICES STATE PLAN REQUIREMENTS § 302.65 Withholding of unemployment compensation. The State plan... State agency charged with the administration of the State unemployment compensation laws in accordance...

38 CFR 3.461 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.461 Dependency...'s award of dependency and indemnity compensation will be apportioned where there is a child or...

38 CFR 3.702 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Concurrent Benefits and Elections § 3.702 Dependency and indemnity compensation. (a) Right to elect. A person who is eligible for death...

Compensation packages: a strategic tool for employees’ performance and retention

Directory of Open Access Journals (Sweden)

Omotayo Adewale OSIBANJO

2014-02-01

Full Text Available The rate at which employees in private universities in Nigeria jump from one university to the other is becoming more disturbing and this could be as a result of compensation packages of different universities to attract competent employees. The aim of this study was to examine the effect of compensation packages on employees’ job performance and retention in a selected private University in Ogun State, South-West Nigeria. A model was developed and tested using one hundred and eleven valid questionnaires which were completed by academics and non-academic staff of the university. The collected data were carefully analyzed using simple percentage supported by structural equation modelling to test the hypotheses and relationships that may exist among the variables under consideration. The results showed strong relationship between compensation packages and employees’ performance and retention. The summary of the findings indicates that there is strong correlation between the tested dependent and independent variables (salary, bonus, incentives, allowances, and fringe benefits. However, management and decision makers should endeavour to review compensation packages at various levels in order to earn employees’ satisfaction and prevention of high labour turnover among the members of staff.

Adaptive compensation control for attitude adjustment of quad-rotor unmanned aerial vehicle.

Science.gov (United States)

Song, Zhankui; Sun, Kaibiao

2017-07-01

A compensation control strategy based on adaptive back-stepping technique is presented to address the problem of attitude adjustment for a quad-rotor unmanned aerial vehicle (QR- UAV) with inertia parameter uncertainties, the limited airflow disturbance and the partial loss of rotation speed effectiveness. In the design process of control system, adaptive estimation technique is introduced into the closed loop system in order to compensate the lumped disturbance term. More specifically, the designed controller utilizes "prescribed performance bounds" method, and therefore guarantees the transient performance of tracking errors, even in the presence of the lumped disturbance. Adaptive compensation algorithms under the proposed closed loop system structure are derived in the sense of Lyapunov stability analysis such that the attitude tracking error converge to a small neighborhood of equilibrium point. Finally, the simulation results demonstrate the effectiveness of the proposed controller. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Geographic variation in expenditures for Workers' Compensation hospitalized claims.

Science.gov (United States)

Miller, T R; Levy, D T

1999-02-01

Past literature finds considerable variation in the cost of physician care and in the utilization of medical procedures. Variation in the cost of hospitalized care has received little attention. We examine injury costs of hospitalized claims across states. Multivariate regression analysis is used to isolate state variations, while controlling for personal and injury characteristics, and state characteristics. Injuries to workers filing Workers' Compensation lost workday claims. About 35,000 randomly sampled Workers' Compensation claims from 17 states filed between 1979 and 1988. Medical payments per episode of three injury groups: upper and lower extremity fractures and dislocations, other upper extremity injuries, and back strains and sprains. Statistical analyses reveal considerable variation in expenditures for hospitalized injuries across states, even after controlling for case mix and state characteristics. A substantial portion of the variation is explained by state rate regulations; regulated states have lower costs. The large variation in costs suggests a potential to affect the costs of hospitalized care. Efforts should be directed at those areas that have higher costs without sufficient input price, quality, or case mix justification.

The big bang? An eventful year in workers' compensation.

Science.gov (United States)

Guidotti, Tee L

2006-01-01

Workers' compensation in the past two years has been dominated by events in California, which have been so fundamental as to merit the term big bang. Passage of Senate Bill 899 has led to a comprehensive program of reform in access to medical care, access to rehabilitation services, temporary and permanent disability, evidence-based management, dispute resolution, and system innovation. Two noteworthy developments thus arose: a new requirement for apportionment by cause in causation analysis, and the adoption of evidence-based criteria for impairment assessment, treatment guidelines, and, soon, utilization review. Elsewhere in the United States, changes were modest, but extensive legislative activity in Texas suggests that Texas will be next to make major changes. In Canada, the Workers' Compensation Board of British Columbia has adopted an ambitious strategic initiative, and there is a Canadawide movement to establish presumption for certain diseases in firefighters. Suggestions for future directions include an increased emphasis on prevention, integration of programs, worker participation, enhancing the expertise of health care professionals, evidence-based management, process evaluation, and opportunities for innovation.

A controllable resistor and its applications in pole-zero tracking frequency compensation methods for LDOs

Energy Technology Data Exchange (ETDEWEB)

Wang Yi; He Lenian; Ning Zhihua; Shao Yali, E-mail: wangyi@vlsi.zju.edu.c [Institute of VLSI Design, Zhejiang University, Hangzhou 310027 (China)

2009-09-15

This paper presents a controllable resistor, which is formed by a MOS-resistor working in the deep triangle region and an auxiliary circuit. The auxiliary circuit can generate the gate-source voltage which is proportional to the output current of an low dropout regulator for the MOS-resistor. Thus, the equivalent output resistance of the MOS-resistor is inversely proportional to the output current, which is a suitable feature for pole-zero tracking frequency compensation methods. By switching the type of the MOS-resistor and current direction through the auxiliary circuit, the controllable resistor can be suitable for different applications. Three pole-zero tracking frequency compensation methods based on a single Miller capacitor with nulling resistor, unit-gain compensation cell and pseudo-ESR (equivalent serial resistor of load capacitor) power stage have been realized by this controllable resistor. Their advantages and limitations are discussed and verified by simulation results.

A controllable resistor and its applications in pole-zero tracking frequency compensation methods for LDOs

International Nuclear Information System (INIS)

Wang Yi; He Lenian; Ning Zhihua; Shao Yali

2009-01-01

This paper presents a controllable resistor, which is formed by a MOS-resistor working in the deep triangle region and an auxiliary circuit. The auxiliary circuit can generate the gate-source voltage which is proportional to the output current of an low dropout regulator for the MOS-resistor. Thus, the equivalent output resistance of the MOS-resistor is inversely proportional to the output current, which is a suitable feature for pole-zero tracking frequency compensation methods. By switching the type of the MOS-resistor and current direction through the auxiliary circuit, the controllable resistor can be suitable for different applications. Three pole-zero tracking frequency compensation methods based on a single Miller capacitor with nulling resistor, unit-gain compensation cell and pseudo-ESR (equivalent serial resistor of load capacitor) power stage have been realized by this controllable resistor. Their advantages and limitations are discussed and verified by simulation results.

Preserved speech abilities and compensation following prefrontal damage.

Science.gov (United States)

Buckner, R L; Corbetta, M; Schatz, J; Raichle, M E; Petersen, S E

1996-02-06

Lesions to left frontal cortex in humans produce speech production impairments (nonfluent aphasia). These impairments vary from subject to subject and performance on certain speech production tasks can be relatively preserved in some patients. A possible explanation for preservation of function under these circumstances is that areas outside left prefrontal cortex are used to compensate for the injured brain area. We report here a direct demonstration of preserved language function in a stroke patient (LF1) apparently due to the activation of a compensatory brain pathway. We used functional brain imaging with positron emission tomography (PET) as a basis for this study.

On the feedback error compensation for adaptive modulation and coding scheme

KAUST Repository

Choi, Seyeong

2011-11-25

In this paper, we consider the effect of feedback error on the performance of the joint adaptive modulation and diversity combining (AMDC) scheme which was previously studied with an assumption of perfect feedback channels. We quantify the performance of two joint AMDC schemes in the presence of feedback error, in terms of the average spectral efficiency, the average number of combined paths, and the average bit error rate. The benefit of feedback error compensation with adaptive combining is also quantified. Selected numerical examples are presented and discussed to illustrate the effectiveness of the proposed feedback error compensation strategy with adaptive combining. Copyright (c) 2011 John Wiley & Sons, Ltd.

Multiple Compensation Consultants and CEO Pay

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Minhat, Marizah

The study examines the practice of employing multiple compensation consultants. Data for a sample of UK companies over the period 2003-2006 are analyzed using a variety of econometric methods. We find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant.

Assessment of Wetland Valuation Processes for Compensation in ...

African Journals Online (AJOL)

The issue of compensation has been debated in various fora; however compensation on wetland resources has not been given the primary place. Wetland valuation like any other type of valuation requires going through stages, which may be more complex than real estate valuation for compensation. This study therefore ...

28 CFR 301.301 - Compensable and noncompensable injuries.

Science.gov (United States)

2010-07-01

... only those injuries suffered during the performance of an inmate's regular work assignment. However... institution, when such work has been approved by staff, may also be compensable. (c) Compensation is not paid... in any activity not related to the actual performance of the work assignment are not compensable, and...

Motion compensated beamforming in synthetic aperture vector flow imaging

DEFF Research Database (Denmark)

Oddershede, Niels; Jensen, Jørgen Arendt

2006-01-01

. In this paper, these motion effects are considered. A number of Field II simulations of a single scatterer moving at different velocities are performed both for axial and lateral velocities from 0 to 1 m/s. Data are simulated at a pulse repetition frequency of 5 kHz. The signal-to-noise ratio (SNR....... Here the SNR is -10 dB compared to the stationary scatterer. A 2D motion compensation method for synthetic aperture vector flow imaging is proposed, where the former vector velocity estimate is used for compensating the beamforming of new data. This method is tested on data from an experimental flow...

CEO Compensation and Disclosure Policy

OpenAIRE

Zhang, Weijia; Zhang, Kun

2016-01-01

This paper examines the relationship between CEO compensation and disclosure policy related to corporate governance information within S&P 500 index. Our sample consists of 456 companies for the period from 2005 to 2015. Most previous researchers mainly put their attention on various corporate governance characteristics such as board size, board independence, and executive ownership when analysing CEO compensation. Our paper extends the previous study by dividing corporate governance into...

Compensator design for improved counterbalancing in high speed atomic force microscopy.

Science.gov (United States)

Bozchalooi, I S; Youcef-Toumi, K; Burns, D J; Fantner, G E

2011-11-01

High speed atomic force microscopy can provide the possibility of many new scientific observations and applications ranging from nano-manufacturing to the study of biological processes. However, the limited imaging speed has been an imperative drawback of the atomic force microscopes. One of the main reasons behind this limitation is the excitation of the AFM dynamics at high scan speeds, severely undermining the reliability of the acquired images. In this research, we propose a piezo based, feedforward controlled, counter actuation mechanism to compensate for the excited out-of-plane scanner dynamics. For this purpose, the AFM controller output is properly filtered via a linear compensator and then applied to a counter actuating piezo. An effective algorithm for estimating the compensator parameters is developed. The information required for compensator design is extracted from the cantilever deflection signal, hence eliminating the need for any additional sensors. The proposed approach is implemented and experimentally evaluated on the dynamic response of a custom made AFM. It is further assessed by comparing the imaging performance of the AFM with and without the application of the proposed technique and in comparison with the conventional counterbalancing methodology. The experimental results substantiate the effectiveness of the method in significantly improving the imaging performance of AFM at high scan speeds. © 2011 American Institute of Physics

Compensation for gravitational sag of bent mirror

Energy Technology Data Exchange (ETDEWEB)

Mao, Chengwen; Jiang, Hui; He, Yan; Liang, Dongxu; Lan, Xuying; Yan, Shuai [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, CAS, Shanghai 201800 (China); Shu, De-ming [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Li, Aiguo, E-mail: aiguo.li@sinap.ac.cn [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, CAS, Shanghai 201800 (China)

2017-05-01

The gravitational sag of aspheric bent mirrors with face-up or face-down geometry produces a nonnegligible optical error. As an effective compensation, width optimization is used to match the combined effects of the gravitational and bending moments. This method is described by analytical expressions and two calculation algorithms. The results of theoretical simulations and finite element analysis have proved that this method can reduce the slope error resulting from gravitational sag to the level of nano radians.

Compensation for gravitational sag of bent mirror

International Nuclear Information System (INIS)

Mao, Chengwen; Jiang, Hui; He, Yan; Liang, Dongxu; Lan, Xuying; Yan, Shuai; Shu, De-ming; Li, Aiguo

2017-01-01

The gravitational sag of aspheric bent mirrors with face-up or face-down geometry produces a nonnegligible optical error. As an effective compensation, width optimization is used to match the combined effects of the gravitational and bending moments. This method is described by analytical expressions and two calculation algorithms. The results of theoretical simulations and finite element analysis have proved that this method can reduce the slope error resulting from gravitational sag to the level of nano radians.

12 CFR 918.2 - Annual directors' compensation policy.

Science.gov (United States)

2010-01-01

... § 918.3. At a minimum, such policy shall address the activities or functions for which attendance is... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Annual directors' compensation policy. 918.2... HOME LOAN BANKS BANK DIRECTOR COMPENSATION AND EXPENSES § 918.2 Annual directors' compensation policy...

Performance of an Orifice Compensated Two-Lobe Hole-Entry Hybrid Journal Bearing

Directory of Open Access Journals (Sweden)

J. Sharana Basavaraja

2008-01-01

Full Text Available The work presented in this paper aims to study the performance of a two-lobe hole-entry hybrid journal bearing system compensated by orifice restrictors. The Reynolds equation governing the flow of lubricant in the clearance space between the journal and bearing together with the equation of flow through an orifice restrictor has been solved using FEM and Galerkin's method. The bearing performance characteristics results have been simulated for an orifice compensated nonrecessed two-lobe hole-entry hybrid journal bearing symmetric configuration for the various values of offset factor (, restrictor design parameter (2, and the value of external load (0. Further, a comparative study of the performance of a two-lobe hole-entry hybrid journal bearing system with a circular hole-entry symmetric hybrid journal bearing system has also been carried out so that a designer has a better flexibility in choosing a suitable bearing configuration. The simulated numerical results indicate that for the two-lobe symmetric hole-entry hybrid journal bearing system with an offset factor ( greater than one provides 30 to 50 percent larger values of direct stiffness and direct damping coefficients as compared to a circular symmetric hole-entry hybrid journal bearing system.

Passive Resistor Temperature Compensation for a High-Temperature Piezoresistive Pressure Sensor.

Science.gov (United States)

Yao, Zong; Liang, Ting; Jia, Pinggang; Hong, Yingping; Qi, Lei; Lei, Cheng; Zhang, Bin; Li, Wangwang; Zhang, Diya; Xiong, Jijun

2016-07-22

The main limitation of high-temperature piezoresistive pressure sensors is the variation of output voltage with operating temperature, which seriously reduces their measurement accuracy. This paper presents a passive resistor temperature compensation technique whose parameters are calculated using differential equations. Unlike traditional experiential arithmetic, the differential equations are independent of the parameter deviation among the piezoresistors of the microelectromechanical pressure sensor and the residual stress caused by the fabrication process or a mismatch in the thermal expansion coefficients. The differential equations are solved using calibration data from uncompensated high-temperature piezoresistive pressure sensors. Tests conducted on the calibrated equipment at various temperatures and pressures show that the passive resistor temperature compensation produces a remarkable effect. Additionally, a high-temperature signal-conditioning circuit is used to improve the output sensitivity of the sensor, which can be reduced by the temperature compensation. Compared to traditional experiential arithmetic, the proposed passive resistor temperature compensation technique exhibits less temperature drift and is expected to be highly applicable for pressure measurements in harsh environments with large temperature variations.

Simulation of wire-compensation of long range beam beam interaction in high energy accelerators

International Nuclear Information System (INIS)

Dorda, U.; )

2006-01-01

Full text: We present weak-strong simulation results for the effect of long-range beam-beam (LRBB) interaction in LHC as well as for proposed wire compensation schemes or wire experiments, respectively. In particular, we discuss details of the simulation model, instability indicators, the effectiveness of compensation, the difference between nominal and PACMAN bunches for the LHC, beam experiments, and wire tolerances. The simulations are performed with the new code BBTrack. (author)

Control of a hybrid compensator in a power network by an artificial neural network

Directory of Open Access Journals (Sweden)

I. S. Shaw

1998-07-01

Full Text Available Increased interest in the elimination of distortion in electrical power networks has led to the development of various compensator topologies. The increasing cost of electrical energy necessitates the cost-effective operation of any of these topologies. This paper considers the development of an artificial neural network based controller, trained by means of the backpropagation method, that ensures the cost-effective operation of the hybrid compensator consisting of various converters and filters.

Impact of beacon wavelength on phase-compensation performance

Science.gov (United States)

Enterline, Allison A.; Spencer, Mark F.; Burrell, Derek J.; Brennan, Terry J.

2017-09-01

This study evaluates the effects of beacon-wavelength mismatch on phase-compensation performance. In general, beacon-wavelength mismatch occurs at the system level because the beacon-illuminator laser (BIL) and high-energy laser (HEL) are often at different wavelengths. Such is the case, for example, when using an aperture sharing element to isolate the beam-control sensor suite from the blinding nature of the HEL. With that said, this study uses the WavePlex Toolbox in MATLAB® to model ideal spherical wave propagation through various atmospheric-turbulence conditions. To quantify phase-compensation performance, we also model a nominal adaptive-optics (AO) system. We achieve correction from a Shack-Hartmann wavefront sensor and continuous-face-sheet deformable mirror using a least-squares phase reconstruction algorithm in the Fried geometry and a leaky integrator control law. To this end, we plot the power in the bucket metric as a function of BIL-HEL wavelength difference. Our initial results show that positive BIL-HEL wavelength differences achieve better phase compensation performance compared to negative BIL-HEL wavelength differences (i.e., red BILs outperform blue BILs). This outcome is consistent with past results.

'Aharonov-Bohm antiferromagnetism' and compensation points in the lattice of quantum rings

International Nuclear Information System (INIS)

Meleshenko, Peter A.; Klinskikh, Alexander F.

2011-01-01

We investigate the magnetic properties of the lattice of non-interacting quantum rings using the 2D rotator model. The exact analytic expressions for the free energy as well as for the magnetization and magnetic susceptibility are found and analyzed. It is shown that such a system can be considered as a system with antiferromagnetic-like properties. We have shown also that all observable quantities in this case (free energy, entropy, magnetization) are periodic functions of the magnetic flux through the ring's area (as well known, such a behavior is typical for the Aharonov-Bohm effect). For the lattice of quantum rings with two different geometric parameters we investigate the ordinary compensation points ('temperature compensation points', i.e. points at which the magnetization vanishes at fixed values of the magnetic field strength). It is shown that the positions of compensation points in the temperature scale are very sensitive to small changes in the magnetic field strength. - Highlights: → The lattice of quantum rings as a system with antiferromagnetic-like properties. → In considered system the 'temperature compensation points' take place. → The 'temperature compensation points' positions depend on the Aharonov-Bohm flux.

Radiobiological compensation: A case study of uterine cervix cancer with concurrent chemotherapy

International Nuclear Information System (INIS)

Herrera, Higmar; Yañez, Elvia; López, Jesús

2012-01-01

The case of a patient diagnosed with uterine cervix cancer is presented as an example of the clinical application of the radiobiological compensation method implemented at Centro Estatal de Cancerología de Durango. Radiotherapy treatment was initially modified to compensate for the chemotherapy component and, as medical complications arose during treatment delivery resulting in an 18 days gap, new compensation followed. All physical and radiobiological assumptions to calculate the Biologically Effective Dose in the external beam and brachytherapy parts of the treatment are presented. Good local control of the tumor was achieved, the theoretical tolerance limits for the organs at risk were not surpassed and the patient manifested no extensive morbidity.

Radiobiological compensation: A case study of uterine cervix cancer with concurrent chemotherapy

Science.gov (United States)

Herrera, Higmar; Yañez, Elvia; López, Jesús

2012-10-01

The case of a patient diagnosed with uterine cervix cancer is presented as an example of the clinical application of the radiobiological compensation method implemented at Centro Estatal de Cancerología de Durango. Radiotherapy treatment was initially modified to compensate for the chemotherapy component and, as medical complications arose during treatment delivery resulting in an 18 days gap, new compensation followed. All physical and radiobiological assumptions to calculate the Biologically Effective Dose in the external beam and brachytherapy parts of the treatment are presented. Good local control of the tumor was achieved, the theoretical tolerance limits for the organs at risk were not surpassed and the patient manifested no extensive morbidity.

Research on the critical parameters initialization of optical PMD compensator in high bit-rate systems

Science.gov (United States)

Zhao, Wenyu; Zhang, Haiyi; Ji, Yuefeng; Xu, Daxiong

2004-05-01

Based on the proposed polarization mode dispersion (PMD) compensation simulation model and statistical analysis method (Monte-Carlo), the critical parameters initialization of two typical optical domain PMD compensators, which include optical PMD method with fixed compensation differential group delay (DGD) and that with variable compensation DGD, are detailedly investigated by numerical method. In the simulation, the line PMD values are chosen as 3ps, 4ps and 5ps and run samples are set to 1000 in order to achieve statistical evaluation for PMD compensated systems, respectively. The simulation results show that for the PMD value pre-known systems, the value of the fixed DGD compensator should be set to 1.5~1.6 times of line PMD value in order to reach the optimum performance, but for the second kind of PMD compensator, the DGD range of lower limit should be 1.5~1.6 times of line PMD provided that of upper limit is set to 3 times of line PMD, if no effective ways are chosen to resolve the problem of local minimum in optimum process. Another conclusion can be drawn from the simulation is that, although the second PMD compensator holds higher PMD compensation performance, it will spend more feedback loops to look up the optimum DGD value in the real PMD compensation realization, and this will bring more requirements on adjustable DGD device, not only wider adjustable range, but rapid adjusting speed for real time PMD equalization.

Theoretical and numerical characterization of a 40 Gbps long-haul multi-channel transmission system with dispersion compensation

Directory of Open Access Journals (Sweden)

Kaikai Xu

2015-08-01

Full Text Available When updating the 10 Gbps optical transmission system to 40 Gbps, the main limits are chromatic dispersion, nonlinear effect, especially the interactions of dispersion and intra-channel nonlinearity. To optimize the performance of standard WDM in a 40 Gbps four-channel transmission system, numerical simulations are carried out to compare three different dispersion compensation techniques (without compensation; periodic dispersion compensation at the front end; and dispensation compensation all at the end of the system by means of highly dispersed pulses for chromatic dispersion on a terrestrial 40 Gbps system. Both the loss and dispersion of the transmission fiber are periodically compensated, since two dispersive elements are placed at the input and the output ends of a compensation period. Due to the interplay between dispersion, nonlinearity and signal power, and the effect of dispersion on the pulse evolution, the pulse compress can be optimized and the system performance can be improved to compare with the system with either pre- or post-dispersion compensation. On comparing pre- and post-compensation methods, it is found that the latter is superior to the former. Further performance optimization includes how to properly match the EDFA power and length of the fiber.

Knockout of the Gnrh genes in zebrafish: effects on reproduction and potential compensation by reproductive and feeding-related neuropeptides.

Science.gov (United States)

Marvel, Miranda; Spicer, Olivia Smith; Wong, Ten-Tsao; Zmora, Nilli; Zohar, Yonathan

2018-04-04

Gonadotropin-releasing hormone (GnRH) is known as a pivotal upstream regulator of reproduction in vertebrates. However, reproduction is not compromised in the hypophysiotropic Gnrh3 knockout line in zebrafish (gnrh3-/-). In order to determine if Gnrh2, the only other Gnrh isoform in zebrafish brains, is compensating for the loss of Gnrh3, we generated a double Gnrh knockout zebrafish line. Surprisingly, the loss of both Gnrh isoforms resulted in no major impact on reproduction, indicating that a compensatory response, outside of the Gnrh system, was evoked. A plethora of factors acting along the reproductive hypothalamus-pituitary axis were evaluated as possible compensators based on neuroanatomical and differential gene expression studies. In addition, we also examined the involvement of feeding factors in the brain as potential compensators for Gnrh2, which has known anorexigenic effects. We found that the double knockout fish exhibited upregulation of several genes in the brain, specifically gonadotropin-inhibitory hormone (gnih), secretogranin 2 (scg2), tachykinin 3a (tac3a), and pituitary adenylate cyclase-activating peptide 1 (pacap1), and downregulation of agouti-related peptide 1 (agrp1), indicating the compensation occurs outside of Gnrh cells and therefore is a non-cell autonomous response to the loss of Gnrh. While the differential expression of gnih and agrp1 in the double knockout line was confined to the periventricular nucleus and hypothalamus, respectively, the upregulation of scg2 corresponded with a broader neuronal redistribution in the lateral hypothalamus and hindbrain. In conclusion, our results demonstrate the existence of a redundant reproductive regulatory system that comes into play when Gnrh2 and Gnrh3 are lost.

Optimizing Fuzzy Rule Base for Illumination Compensation in Face Recognition using Genetic Algorithms

Directory of Open Access Journals (Sweden)

Bima Sena Bayu Dewantara

2014-12-01

Full Text Available Fuzzy rule optimization is a challenging step in the development of a fuzzy model. A simple two inputs fuzzy model may have thousands of combination of fuzzy rules when it deals with large number of input variations. Intuitively and trial‐error determination of fuzzy rule is very difficult. This paper addresses the problem of optimizing Fuzzy rule using Genetic Algorithm to compensate illumination effect in face recognition. Since uneven illumination contributes negative effects to the performance of face recognition, those effects must be compensated. We have developed a novel algorithmbased on a reflectance model to compensate the effect of illumination for human face recognition. We build a pair of model from a single image and reason those modelsusing Fuzzy.Fuzzy rule, then, is optimized using Genetic Algorithm. This approachspendsless computation cost by still keepinga high performance. Based on the experimental result, we can show that our algorithm is feasiblefor recognizing desired person under variable lighting conditions with faster computation time. Keywords: Face recognition, harsh illumination, reflectance model, fuzzy, genetic algorithm

Vibration-Driven Microrobot Positioning Methodologies for Nonholonomic Constraint Compensation

Directory of Open Access Journals (Sweden)

Kostas Vlachos

2015-03-01

Full Text Available This paper presents the formulation and practical implementation of positioning methodologies that compensate for the nonholonomic constraints of a mobile microrobot that is driven by two vibrating direct current (DC micromotors. The open-loop and closed-loop approaches described here add the capability for net sidewise displacements of the microrobotic platform. A displacement is achieved by the execution of a number of repeating steps that depend on the desired displacement, the speed of the micromotors, and the elapsed time. Simulation and experimental results verified the performance of the proposed methodologies.

Can money heal all wounds? Social exchange norm modulates the preference for monetary versus social compensation

Directory of Open Access Journals (Sweden)

Yulong eCao

2015-09-01

Full Text Available Compensation is a kind of pro-social behavior that can restore a social relationship jeopardized by interpersonal transgression. The effectiveness of a certain compensation strategy (e.g., repaying money, sharing loss, etc. may vary as a function of the social norm/relationship. Previous studies have shown that two types of norms (or relationships, monetary/exchange and social/communal, differentially characterize people’s appraisal of and response to social exchanges. In this study, we investigated how individual differences in preference for these norms affect individuals’ perception of others’ as well as the selection of their own reciprocal behaviors. In a two-phase experiment with interpersonal transgression, we asked the participant to perform a dot-estimation task with two partners who occasionally and unintentionally inflict noise stimulation upon the participant (first phase. As compensation one partner give money to the participant 80% of the time (the monetary partner and the other bear the noise for the participant 80% of the time (the social partner. Results showed that the individuals’ preference for compensation (repaying money versus bearing harm affected their relationship (exchange versus communal with the partners adopting different compensation strategies: participants tended to form communal relationships and felt closer to the partner whose compensation strategy matched their own preference. The participants could be differentiated into a social group, who tended to form communal relationship with the social partner, and a monetary group, who tended to form communal relationship with the monetary partner. In the second phase of the experiment, when the participants became transgressors and were asked to compensate for their transgression with money, the social group offered more compensation to the social partners than to the monetary partners, while the monetary group compensated less than the social group in

Can money heal all wounds? Social exchange norm modulates the preference for monetary versus social compensation.

Science.gov (United States)

Cao, Yulong; Yu, Hongbo; Wu, Yanhong; Zhou, Xiaolin

2015-01-01

Compensation is a kind of pro-social behavior that can restore a social relationship jeopardized by interpersonal transgression. The effectiveness of a certain compensation strategy (e.g., repaying money, sharing loss, etc.) may vary as a function of the social norm/relationship. Previous studies have shown that two types of norms (or relationships), monetary/exchange and social/communal, differentially characterize people's appraisal of and response to social exchanges. In this study, we investigated how individual differences in preference for these norms affect individuals' perception of others' as well as the selection of their own reciprocal behaviors. In a two-phase experiment with interpersonal transgression, we asked the participant to perform a dot-estimation task with two partners who occasionally and unintentionally inflicted noise stimulation upon the participant (first phase). As compensation one partner gave money to the participant 80% of the time (the monetary partner) and the other bore the noise for the participant 80% of the time (the social partner). Results showed that the individuals' preference for compensation (repaying money versus bearing noise) affected their relationship (exchange versus communal) with the partners adopting different compensation strategies: participants tended to form communal relationships and felt closer to the partner whose compensation strategy matched their own preference. The participants could be differentiated into a social group, who tended to form communal relationship with the social partner, and a monetary group, who tended to form communal relationship with the monetary partner. In the second phase of the experiment, when the participants became transgressors and were asked to compensate for their transgression with money, the social group offered more compensation to the social partners than to the monetary partners, while the monetary group compensated less than the social group in general and showed no

Towards Compensation Correctness in Interactive Systems

Science.gov (United States)

Vaz, Cátia; Ferreira, Carla

One fundamental idea of service-oriented computing is that applications should be developed by composing already available services. Due to the long running nature of service interactions, a main challenge in service composition is ensuring correctness of failure recovery. In this paper, we use a process calculus suitable for modelling long running transactions with a recovery mechanism based on compensations. Within this setting, we discuss and formally state correctness criteria for compensable processes compositions, assuming that each process is correct with respect to failure recovery. Under our theory, we formally interpret self-healing compositions, that can detect and recover from failures, as correct compositions of compensable processes.

Charge compensation and the incorporation of cerium in zirconolite and perovskite

International Nuclear Information System (INIS)

Begg, B.D.; Vance, E.R.; Lumpkin, G.R.

1998-01-01