Direct asymmetric vinylogous aldol reaction of allyl ketones with isatins: Divergent synthesis of 3-hydroxy-2-oxindole derivatives

KAUST Repository

Zhu, Bo

2013-05-03

6 in 1: The highly enantioselective title reaction is mediated by a bifunctional catalyst and leads to E-configured vinylogous aldol products (see scheme). These products are used as common intermediates in the synthesis of six biologically active 3-hydroxy-2-oxindole derivatives (e.g., CPC-1). Computational studies indicated that the observed stereoselectivity is a result of favorable secondary π-π* and H-bonding interactions in the transition state. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Modified calcium oxide as stable solid base catalyst for Aldol ...

Indian Academy of Sciences (India)

A highly efficient and stable solid-base catalyst for Aldol condensation was ... was bonded on surface of CaO chemically and almost no Ca(OH)2 formed during the modification process. ... cation, corrosion and waste generation attract great.

Catalyst-free aldol reaction of N-substituted rhodanines on aqueous ...

Indian Academy of Sciences (India)

N S DEVI

2018-02-07

Feb 7, 2018 ... catalytic aldol reaction is very common in organic sol- vents and ... −1. ). 1H NMR and 13C NMR spectra were recorded at 400 and 100 MHz in CDCl3. Chemical shifts ... 2.2 General procedure for the synthesis of rhodanine.

An overview of dehydration, aldol-condensation and hydrogenation processes for production of liquid alkanes from biomass-derived carbohydrates

Energy Technology Data Exchange (ETDEWEB)

Chheda, Juben N.; Dumesic, James A. [University of Wisconsin-Madison, Department of Chemical and Biological Engineering, Madison, WI 53706 (United States)

2007-05-30

We present results for the conversion of carbohydrate feedstocks to liquid alkanes by the combination of dehydration, aldol-condensation/hydrogenation, and dehydration/hydrogenation processing. With respect to the first dehydration step, we demonstrate that HMF can be produced in good selectivity from abundantly available polysaccharides (such as inulin, sucrose) containing fructose monomer units using a biphasic batch reactor system. The reaction system can be optimized to achieve good yields to 5-hydroxymethylfurfural (HMF) from fructose by varying the contents of aqueous-phase modifiers such as dimethylsulfoxide (DMSO) and 1-methyl-2-pyrrolidinone (NMP). Regarding the aldol-condensation/hydrogenation step, we present the development of stable, solid base catalysts in aqueous environments. We address the effects of various reaction parameters such as the molar ratio of reactants and temperature on overall product yield for sequential aldol-condensation and hydrogenation steps. Overall, our results show that it is technically possible to convert carbohydrate feedstocks to produce liquid alkanes by the combination of dehydration, aldol-condensation/hydrogenation, and dehydration/hydrogenation processing; however, further optimization of these processes is required to decrease the overall number of separate steps (and reactors) required in this conversion. (author)

Aggregation and Cooperative Effects in the Aldol Reactions of Lithium Enolates

NARCIS (Netherlands)

Larrañaga, O.; de Cózar, A.; Bickelhaupt, F.M.; Zangi, R.; Cossío, F.P.

2013-01-01

Density functional theory and Car-Parrinello molecular dynamics simulations have been carried out for model aldol reactions involving aggregates of lithium enolates derived from acetaldehyde and acetone. Formaldehyde and acetone have been used as electrophiles. It is found that the geometries of the

Aldol Reactions of Axially Chiral 5-Methyl-2-(o-arylimino-3-(o-aryl-thiazolidine-4-ones

Directory of Open Access Journals (Sweden)

Sule Erol Gunal

2016-06-01

Full Text Available Axially chiral 5-methyl-2-(o-arylimino-3-(o-aryl-thiazolidine-4-ones have been subjected to aldol reactions with benzaldehyde to produce secondary carbinols which have been found to be separable by HPLC on a chiral stationary phase. Based on the reaction done on a single enantiomer resolved via a chromatographic separation from a racemic mixture of 5-methyl-2-(α-naphthylimino-3-(α-naphthyl-thiazolidine-4-one by HPLC on a chiral stationary phase, the aldol reaction was shown to proceed via an enolate intermediate. The axially chiral enolate of the thiazolidine-4-one was found to shield one face of the heterocyclic ring rendering face selectivity with respect to the enolate. The selectivities observed at C-5 of the ring varied from none to 11.5:1 depending on the size of the ortho substituent. Although the aldol reaction proceeded with a lack of face selectivity with respect to benzaldehyde, recrystallization returned highly diastereomerically enriched products.

Cooperative Effects Between Arginine and Glutamic Acid in the Amino Acid-Catalyzed Aldol Reaction.

Science.gov (United States)

Valero, Guillem; Moyano, Albert

2016-08-01

Catalysis of the aldol reaction between cyclohexanone and 4-nitrobenzaldehyde by mixtures of L-Arg and of L-Glu in wet dimethyl sulfoxide (DMSO) takes place with higher enantioselectivity (up to a 7-fold enhancement in the anti-aldol for the 1:1 mixture) than that observed when either L-Glu or L-Arg alone are used as the catalysts. These results can be explained by the formation of a catalytically active hydrogen-bonded complex between both amino acids, and demonstrate the possibility of positive cooperative effects in catalysis by two different α-amino acids. Chirality 28:599-605, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Synthesis of D-manno-heptulose via a cascade aldol/hemiketalization reaction

Directory of Open Access Journals (Sweden)

Yan Chen

2017-04-01

Full Text Available A [4 + 3] synthesis of D-manno-heptulose is described. The cascade aldol/hemiketalization reaction of a C4 aldehyde with a C3 ketone provides the differentially protected ketoheptose building block, which can be further reacted to furnish target D-manno-heptulose.

Enantioselective H-atom transfer reaction: a strategy to synthesize formaldehyde aldol products.

Science.gov (United States)

Sibi, Mukund P; Patil, Kalyani

2005-04-14

[reaction: see text] Enantioselective radical alkylation of Baylis-Hillman adducts furnished aldol products in good yield and selectivity. The results illustrate that the selectivity in the hydrogen atom transfer is dependent on the size of the ester substituent, with smaller substituents providing better enantioselectivity.

1,5-Asymmetric induction in the boron-mediated aldol reaction of β-oxygenated methyl ketones

International Nuclear Information System (INIS)

Dias, Luiz C.

2007-01-01

High levels of substrate-based 1,5-stereo induction are obtained in the boron-mediated aldol reactions of β-oxygenated methyl ketones with achiral and chiral aldehydes. Remote induction from the boron enolates gives the 1,5-anti adducts, with the enolate pi-facial selectivity critically dependent upon the nature of the beta-alkoxy protecting group. This 1,5-anti aldol methodology has been strategically employed in the total synthesis of several natural products. At present, the origin of the high level of 1,5-anti induction obtained with the boron enolates is unclear, although a model based on a hydrogen bonding between the alkoxy oxygen and the formyl hydrogen has been recently proposed. (author)

A green route to methyl acrylate and acrylic acid by an aldol condensation reaction over H-ZSM-35 zeolite catalysts.

Science.gov (United States)

Ma, Zhanling; Ma, Xiangang; Liu, Hongchao; He, Yanli; Zhu, Wenliang; Guo, Xinwen; Liu, Zhongmin

2017-08-10

A one-step aldol condensation reaction to produce MA and AA is a green and promising strategy. Here, the aldol condensation reaction was first conducted with DMM and MAc over different types of zeolite catalysts. The H-ZSM-35 zeolite demonstrates excellent catalytic performance with a DMM conversion of 100% and a MA + AA selectivity of up to 86.2% and superior regeneration ability, with great potential for industrial operation.

Regio- and Stereoselective Cascades via Aldol Condensation and 1,3-Dipolar Cycloaddition for Construction of Functional Pyrrolizidine Derivatives.

Science.gov (United States)

Mao, Zhuo-Ya; Liu, Yi-Wen; Han, Pan; Dong, Han-Qing; Si, Chang-Mei; Wei, Bang-Guo; Lin, Guo-Qiang

2018-02-16

An efficient and step-economical approach to access functionalized pyrrolizidine derivatives by a one-pot tandem sequence, including an aldol condensation and subsequent 1,3-dipolar cycloaddition process, has been developed, starting from acetone, aldehyde, and proline. A number of substituted aromatic aldehydes were amenable to this transformation, and the desired products, racemic 7a-7w and chiral 9a-9m, were obtained with excellent regioselectivities and outstanding diastereoselectivities. Moreover, in situ NMR studies revealed MgSO 4 could effectively promote the aldol condensation pathway in this tandem process.

Molecular shape selectivity of hydrotalcite in mixed aldol condensations of aldehydes and ketones

Czech Academy of Sciences Publication Activity Database

Červený, J.; Šplíchalová, J.; Kačer, P.; Kovanda, F.; Kuzma, Marek; Červený, L.

2008-01-01

Roč. 285, 1-2 (2008), s. 150-154 ISSN 1381-1169 R&D Projects: GA ČR GA104/07/1239 Institutional research plan: CEZ:AV0Z50200510 Keywords : hydrocalcite * aldol condensation * molecular modeling Subject RIV: EE - Microbiology, Virology Impact factor: 2.814, year: 2008

Cross-Aldol condensation of isobutyraldehyde and formaldehyde using phase transfer catalyst

Directory of Open Access Journals (Sweden)

Azhar Hashmi

2016-09-01

Full Text Available The hydroxypivaldehyde (HPA precursor intermediate for the synthesis of neopentyl glycol (NPG is prepared by novel cross Aldol condensation of isobutyraldehyde and formaldehyde at 20 °C using benzyltrimethylammonium hydroxide, a basic phase transfer catalyst. A feed mole ratio of 1.1:1.0:0.04 (isobutyraldehyde:formaldehyde:benzyltrimethylammonium hydroxide afforded hydroxypivaldehyde as white solid in almost quantitative yield with ∼100% selectivity.

Cross-Aldol condensation of isobutyraldehyde and formaldehyde using phase transfer catalyst

OpenAIRE

Azhar Hashmi

2016-01-01

The hydroxypivaldehyde (HPA) precursor intermediate for the synthesis of neopentyl glycol (NPG) is prepared by novel cross Aldol condensation of isobutyraldehyde and formaldehyde at 20 °C using benzyltrimethylammonium hydroxide, a basic phase transfer catalyst. A feed mole ratio of 1.1:1.0:0.04 (isobutyraldehyde:formaldehyde:benzyltrimethylammonium hydroxide) afforded hydroxypivaldehyde as white solid in almost quantitative yield with ∼100% selectivity.

Pd/NbOPO₄ multifunctional catalyst for the direct production of liquid alkanes from aldol adducts of furans.

Science.gov (United States)

Xia, Qi-Neng; Cuan, Qian; Liu, Xiao-Hui; Gong, Xue-Qing; Lu, Guan-Zhong; Wang, Yan-Qin

2014-09-08

Great efforts have been made to convert renewable biomass into transportation fuels. Herein, we report the novel properties of NbO(x)-based catalysts in the hydrodeoxygenation of furan-derived adducts to liquid alkanes. Excellent activity and stability were observed with almost no decrease in octane yield (>90% throughout) in a 256 h time-on-stream test. Experimental and theoretical studies showed that NbO(x) species play the key role in C-O bond cleavage. As a multifunctional catalyst, Pd/NbOPO4 plays three roles in the conversion of aldol adducts into alkanes: 1) The noble metal (in this case Pd) is the active center for hydrogenation; 2) NbO(x) species help to cleave the C-O bond, especially of the tetrahydrofuran ring; and 3) a niobium-based solid acid catalyzes the dehydration, thus enabling the quantitative conversion of furan-derived adducts into alkanes under mild conditions. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

ALDOL- AND MANNICH-TYPE REACTIONS VIA IN SITU OLEFIN MIGRATION IN IONIC LIQUID

Science.gov (United States)

An aldol-type and a Mannich-type reaction via the cross-coupling of aldehydes and imines with allylic alcohols catalyzed by RuCl2(PPh3)3 was developed with ionic liquid as the solvent. The solvent/catalyst system could be reused for at least five times with no loss of reactiv...

Aldol Condensation of Citral with Acetone on Basic Solid Catalysts

Directory of Open Access Journals (Sweden)

NODA C.

1998-01-01

Full Text Available The catalytic performance of solids with basic properties, such as CaO, MgO and hydrotalcites, was evaluated in the aldol condensation of citral and acetone, the first step in the synthesis of ionones from citral. The best results were obtained with CaO and hydrotalcite with high conversions (98% and selectivities (close to 70% for the main product observed for both of the catalyst. Such pseudoionone yields were greater than those reported in the literature for the homogeneous reaction.

RUTHENIUM-CATALYZED TANDEM OLEFIN MIGRATION-ALDOL AND MANNICH-TYPE REACTIONS IN IONIC LIQUID.

Science.gov (United States)

In the presence of a catalytic amount of RuCl2(PPh3)3, a cross-coupling of 3-buten-2-ol with aldehydes and imines was developed via a tandem olefin migration--aldol--Mannich reaction in bmim[PF6]. With In(OAc)3 as a co-catalyst, a-vinylbenzyl alcohol and aldehydes underwent sim...

Operando Spectroscopy of the Gas-Phase Aldol Condensation of Propanal over Solid Base Catalysts

NARCIS (Netherlands)

Hernández-giménez, Ana M.; Ruiz-martínez, Javier; Puértolas, Begoña; Pérez-ramírez, Javier; Bruijnincx, Pieter C. A.; Weckhuysen, Bert M.

2017-01-01

The gas-phase aldol condensation of propanal, taken as model for the aldehyde components in bio-oils, has been studied with a combined operando set-up allowing to perform FT-IR & UV–Vis diffuse reflectance spectroscopy (DRS) with on-line mass spectrometry (MS). The selected solid base catalysts, a

Cooperative organocatalysis of Mukaiyama-type aldol reactions by thioureas and nitro compounds

KAUST Repository

Bukhriakov, Konstantin; Desyatkin, Victor G.; Rodionov, Valentin

2016-01-01

A unique organocatalytic system for Mukaiyama-type aldol reactions based on the cooperative action of nitro compounds and thioureas has been identified. This system is compatible with a wide range of substrates and does not require low temperatures, inert atmospheres, or an aqueous workup. A catalytic mechanism based on nitro group-mediated silyl cation transfer has been proposed. © The Royal Society of Chemistry 2016.

Cooperative organocatalysis of Mukaiyama-type aldol reactions by thioureas and nitro compounds

KAUST Repository

Bukhriakov, Konstantin

2016-05-16

A unique organocatalytic system for Mukaiyama-type aldol reactions based on the cooperative action of nitro compounds and thioureas has been identified. This system is compatible with a wide range of substrates and does not require low temperatures, inert atmospheres, or an aqueous workup. A catalytic mechanism based on nitro group-mediated silyl cation transfer has been proposed. © The Royal Society of Chemistry 2016.

Heterogeneously Catalysed Aldol Reactions in Supercritical Carbon Dioxide as Innovative and Non-Flammable Reaction Medium

DEFF Research Database (Denmark)

Musko, Nikolai; Grunwaldt, Jan-Dierk

2011-01-01

Aldol reactions of several aldehydes have been investigated over acidic and basic catalysts in supercritical carbon dioxide at 180 bar and 100 °C. Both acidic (Amberlyst-15, tungstosilicic acid (TSA) on SiO2 and MCM-41) and basic (hydrotalcite) materials showed interesting performance in this pre...

Enantioselective organocatalyzed Oxa-Michael-Aldol cascade reactions: Construction of chiral 4H-chromenes with a trifluoromethylated tetrasubstituted carbon stereocenter

KAUST Repository

Zhang, Jing; Ajitha, Manjaly John; He, Lin; Liu, Kai; Dai, Bin; Huang, Kuo-Wei

2015-01-01

The first organocatalytic asymmetric synthesis of 4H-chromenes bearing a trifluoromethylated tetrasubstituted carbon center is presented. Chiral secondary amines promote the oxa-Michael-aldol cascade reaction between alkynals and 2

Halogeno Aldol Reaction of Ethyl Vinyl Ketone and Aldehydes Mediated by Titanium Tetrachloride

Directory of Open Access Journals (Sweden)

Guigen Li

2000-12-01

Full Text Available A three-component halogeno aldol reaction has been developed by using titanium tetrachloride as the halogen source as well as the Lewis acid mediator. The dehydration and elimination of hydrogen chloride were inhibited by conducting the reaction at 0 °C in dichloromethane or at room temperature with a shortened reaction time. Seven examples were examined, giving good to high yields (61 - 92% and modest stereoselectivity (syn/anti: 2.2/1.0 - 8.4/1.0.

N-Heterocyclic Carbene-Catalyzed Vinylogous Mukaiyama Aldol Reaction of α-Keto Esters and α-Trifluoromethyl Ketones

KAUST Repository

Du, Guang-Fen; Wang, Ying; Xing, Fen; Xue, Mei; Guo, Xu-Hong; Huang, Kuo-Wei; Dai, Bin

2015-01-01

© Georg Thieme Verlag Stuttgart · New York · Synthesis 2016. N-Heterocyclic carbene (NHC)-catalyzed vinylogous Mukaiyama aldol reaction of ketones was developed. Under the catalysis of 5 mol% NHC, α-keto esters and α-trifluoromethyl ketones reacted with 2-(trimethysilyloxy)furan efficiently to produce γ-substituted butenolides containing adjacent quaternary and tertiary carbon centers in high yields with good diastereoselectivities.

Forging Fluorine‐Containing Quaternary Stereocenters by a Light‐Driven Organocatalytic Aldol Desymmetrization Process

Science.gov (United States)

Cuadros, Sara; Dell'Amico, Luca

2017-01-01

Abstract Reported herein is a light‐triggered organocatalytic strategy for the desymmetrization of achiral 2‐fluoro‐substituted cyclopentane‐1,3‐diketones. The chemistry is based on an intermolecular aldol reaction of photochemically generated hydroxy‐o‐quinodimethanes and simultaneously forges two adjacent fully substituted carbon stereocenters, with one bearing a stereogenic carbon–fluorine unit. The method uses readily available substrates, a simple chiral organocatalyst, and mild reaction conditions to afford an array of highly functionalized chiral 2‐fluoro‐3‐hydroxycyclopentanones. PMID:28746742

Forging Fluorine-Containing Quaternary Stereocenters by a Light-Driven Organocatalytic Aldol Desymmetrization Process.

Science.gov (United States)

Cuadros, Sara; Dell'Amico, Luca; Melchiorre, Paolo

2017-09-18

Reported herein is a light-triggered organocatalytic strategy for the desymmetrization of achiral 2-fluoro-substituted cyclopentane-1,3-diketones. The chemistry is based on an intermolecular aldol reaction of photochemically generated hydroxy-o-quinodimethanes and simultaneously forges two adjacent fully substituted carbon stereocenters, with one bearing a stereogenic carbon-fluorine unit. The method uses readily available substrates, a simple chiral organocatalyst, and mild reaction conditions to afford an array of highly functionalized chiral 2-fluoro-3-hydroxycyclopentanones. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Theoretical insights into the sites and mechanisms for base catalyzed esterification and aldol condensation reactions over Cu.

Science.gov (United States)

Neurock, Matthew; Tao, Zhiyuan; Chemburkar, Ashwin; Hibbitts, David D; Iglesia, Enrique

2017-04-28

Condensation and esterification are important catalytic routes in the conversion of polyols and oxygenates derived from biomass to fuels and chemical intermediates. Previous experimental studies show that alkanal, alkanol and hydrogen mixtures equilibrate over Cu/SiO 2 and form surface alkoxides and alkanals that subsequently promote condensation and esterification reactions. First-principle density functional theory (DFT) calculations were carried out herein to elucidate the elementary paths and the corresponding energetics for the interconversion of propanal + H 2 to propanol and the subsequent C-C and C-O bond formation paths involved in aldol condensation and esterification of these mixtures over model Cu surfaces. Propanal and hydrogen readily equilibrate with propanol via C-H and O-H addition steps to form surface propoxide intermediates and equilibrated propanal/propanol mixtures. Surface propoxides readily form via low energy paths involving a hydrogen addition to the electrophilic carbon center of the carbonyl of propanal or via a proton transfer from an adsorbed propanol to a vicinal propanal. The resulting propoxide withdraws electron density from the surface and behaves as a base catalyzing the activation of propanal and subsequent esterification and condensation reactions. These basic propoxides can readily abstract the acidic C α -H of propanal to produce the CH 3 CH (-) CH 2 O* enolate, thus initiating aldol condensation. The enolate can subsequently react with a second adsorbed propanal to form a C-C bond and a β-alkoxide alkanal intermediate. The β-alkoxide alkanal can subsequently undergo facile hydride transfer to form the 2-formyl-3-pentanone intermediate that decarbonylates to give the 3-pentanone product. Cu is unique in that it rapidly catalyzes the decarbonylation of the C 2n intermediates to form C 2n-1 3-pentanone as the major product with very small yields of C 2n products. This is likely due to the absence of Brønsted acid sites

Application of a new tandem isomerization-aldolization reaction of allylic alcohols to the synthesis of three diastereoisomers of (2R)-1,2-O-isopropylidene-4-methylpentane-1,2,3,5-tetraol.

Science.gov (United States)

Cuperly, David; Crévisy, Christophe; Grée, René

2003-08-08

The tandem isomerization-aldolization reaction of (2R)-1,2-O-isopropylidene-4-penten-1,2,3-triol 3 and formaldehyde gives a mixture of two aldol products 2a and 2b. The stereoselective reduction of each compound by l-Selectride affords two diastereoisomers of (2R)-1,2-O-Isopropylidene-4-methylpentane-1,2,3,5-tetraol while a third diastereoisomer is obtained by stereoselective reduction with Me(4)NHB(OAc)(3).

Toward understanding of the role of Lewis acidity in aldol condensation of acetone and furfural using MOF and zeolite catalysts

Czech Academy of Sciences Publication Activity Database

Kikhtyanin, O.; Kubička, D.; Čejka, Jiří

2015-01-01

Roč. 243, APR 2015 (2015), s. 158-162 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : metal organic framework * aldol condensation * acidic catalysis Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.312, year: 2015

Expedient synthesis of C-aryl carbohydrates by consecutive biocatalytic benzoin and aldol reactions.

Science.gov (United States)

Hernández, Karel; Parella, Teodor; Joglar, Jesús; Bujons, Jordi; Pohl, Martina; Clapés, Pere

2015-02-16

The introduction of aromatic residues connected by a C-C bond into the non-reducing end of carbohydrates is highly significant for the development of innovative structures with improved binding affinity and selectivity (e.g., C-aril-sLex). In this work, an expedient asymmetric "de novo" synthetic route to new aryl carbohydrate derivatives based on two sequential stereoselectively biocatalytic carboligation reactions is presented. First, the benzoin reaction of aromatic aldehydes to dimethoxyacetaldehyde is conducted, catalyzed by benzaldehyde lyase from Pseudomonas fluorescens biovar I. Then, the α-hydroxyketones formed are reduced by using NaBH4 yielding the anti diol. After acetal hydrolysis, the aldol addition of dihydroxyacetone, hydroxyacetone, or glycolaldehyde catalyzed by the stereocomplementary D-fructose-6-phosphate aldolase and L-rhamnulose-1-phosphate aldolase is performed. Both aldolases accept unphosphorylated donor substrates, avoiding the need of handling the phosphate group that the dihydroxyacetone phosphate-dependent aldolases require. In this way, 6-C-aryl-L-sorbose, 6-C-aryl-L-fructose, 6-C-aryl-L-tagatose, and 5-C-aryl-L-xylose derivatives are prepared by using this methodology. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tandem Aldol-Michael Reactions in Aqueous Diethylamine Medium: A Greener and Efficient Approach to Bis-Pyrimidine Derivatives

Directory of Open Access Journals (Sweden)

Abdullah M. Al-Majid

2013-12-01

Full Text Available A simple protocol, involving the green synthesis for the construction of novel bis-pyrimidine derivatives, 3a–i and 4a–e are accomplished by the aqueous diethylamine media promoted tandem Aldol-Michael reaction between two molecules of barbituric acid derivatives 1a,b with various aldehydes. This efficient synthetic protocol using an economic and environmentally friendly reaction media with versatility and shorter reaction time provides bis-pyrimidine derivatives with high yields (88%–99%.

Convergent fabrication of a nanoporous two-dimensional carbon network from an aldol condensation on metal surfaces

International Nuclear Information System (INIS)

Landers, John; De Santis, Maurizio; Bendiab, Nedjma; Magaud, Laurence; Coraux, Johann; Chérioux, Frédéric; Lamare, Simon

2014-01-01

We report a convergent surface polymerization reaction scheme on Au(111), based on a triple aldol condensation, yielding a carbon-rich, covalent nanoporous two-dimensional network. The reaction is not self-poisoning and proceeds up to a full surface coverage. The deposited precursor molecules 1, 3, 5-tri(4’-acetylphenyl) first form supramolecular assemblies that are converted to the porous covalent network upon heating. The formation and structure of the network and of the intermediate steps are studied with scanning tunneling microscopy, Raman spectroscopy and density functional theory. (paper)

Enantioselective organocatalyzed Oxa-Michael-Aldol cascade reactions: Construction of chiral 4H-chromenes with a trifluoromethylated tetrasubstituted carbon stereocenter

KAUST Repository

Zhang, Jing

2015-03-13

The first organocatalytic asymmetric synthesis of 4H-chromenes bearing a trifluoromethylated tetrasubstituted carbon center is presented. Chiral secondary amines promote the oxa-Michael-aldol cascade reaction between alkynals and 2-trifluoroacetylphenols via iminium-allenamine activation to produce pharmaceutically important heterocycles with excellent enantioselectivities. The proposed reaction can be scaled-up easily with maintenance of the excellent enantioselectivity. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cross-Aldol Reaction of Activated Carbonyls with Nitrosocarbonyl Intermediates: Stereoselective Synthesis toward α-Hydroxy-β-amino Esters and Amides.

Science.gov (United States)

Mallik, Sumitava; Bhajammanavar, Vinod; Ramakrishna, Isai; Baidya, Mahiuddin

2017-07-21

A practical and flexible strategy toward α-hydroxy-β-amino esters and amides, which are important biological motifs, based on an organocatalytic cross-aldol reaction of in situ-generated nitrosocarbonyl intermediates followed by hydrogenation is presented. The protocol features operational simplicity, high yields, a wide substrate scope, and high regio- and diastereoselectivity profiles. The utility of this method was showcased through the synthesis of bestatin analogues and indole formation.

Free-radical-mediated conjugate additions. Enantioselective synthesis of butyrolactone natural products: (-)-enterolactone, (-)-arctigenin, (-)-isoarctigenin, (-)-nephrosteranic acid, and (-)-roccellaric acid.

Science.gov (United States)

Sibi, Mukund P; Liu, Pingrong; Ji, Jianguo; Hajra, Saumen; Chen, Jian-xie

2002-03-22

Lewis acid-mediated conjugate addition of alkyl radicals to a differentially protected fumarate 10 produced the monoalkylated succinates with high chemical efficiency and excellent stereoselectivity. A subsequent alkylation or an aldol reaction furnished the disubstituted succinates with syn configuration. The chiral auxiliary, 4-diphenylmethyl-2-oxazolidinone, controlled the stereoselectivity in both steps. Manipulation of the disubstituted succinates obtained by alkylation furnished the natural products (-)-enterolactone, (-)-arctigenin, and (-)-isoarctigenin. The overall yields for the target natural products were 20-26% over six steps. Selective functionalization of the disubstituted succinates obtained by aldol condensation gave the paraconic acid natural products (-)-nephrosteranic acid (8) and (-)-roccellaric acid (9). The overall yield of the natural products 8 and 9 over four steps was 53% and 42%, respectively.

Production of Low-Freezing-Point Highly Branched Alkanes through Michael Addition.

Science.gov (United States)

Jing, Yaxuan; Xia, Qineng; Liu, Xiaohui; Wang, Yanqin

2017-12-22

A new approach for the production of low-freezing-point, high-quality fuels from lignocellulose-derived molecules was developed with Michael addition as the key step. Among the investigated catalysts, CoCl 2 ⋅6 H 2 O was found most active for the Michael addition of 2,4-pentanedione with FA (single aldol adduct of furfural and acetone, 4-(2-furanyl)-3-butene-2-one). Over CoCl 2 ⋅6 H 2 O, a high carbon yield of C 13 oxygenates (about 75 %) can be achieved under mild conditions (353 K, 20 h). After hydrodeoxygenation, low-freezing-point (hydrodeoxygenation, high density (0.8415 g mL -1 ) and low-freezing-point (<223 K) branched alkanes with 18, 23 carbons within lubricant range were also obtained over a Pd/NbOPO 4 catalyst. These highly branched alkanes can be directly used as transportation fuels or additives. This work opens a new strategy for the synthesis of highly branched alkanes with low freezing point from renewable biomass. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Additive direct-write microfabrication for MEMS: A review

Science.gov (United States)

Teh, Kwok Siong

2017-12-01

Direct-write additive manufacturing refers to a rich and growing repertoire of well-established fabrication techniques that builds solid objects directly from computer- generated solid models without elaborate intermediate fabrication steps. At the macroscale, direct-write techniques such as stereolithography, selective laser sintering, fused deposition modeling ink-jet printing, and laminated object manufacturing have significantly reduced concept-to-product lead time, enabled complex geometries, and importantly, has led to the renaissance in fabrication known as the maker movement. The technological premises of all direct-write additive manufacturing are identical—converting computer generated three-dimensional models into layers of two-dimensional planes or slices, which are then reconstructed sequentially into threedimensional solid objects in a layer-by-layer format. The key differences between the various additive manufacturing techniques are the means of creating the finished layers and the ancillary processes that accompany them. While still at its infancy, direct-write additive manufacturing techniques at the microscale have the potential to significantly lower the barrier-of-entry—in terms of cost, time and training—for the prototyping and fabrication of MEMS parts that have larger dimensions, high aspect ratios, and complex shapes. In recent years, significant advancements in materials chemistry, laser technology, heat and fluid modeling, and control systems have enabled additive manufacturing to achieve higher resolutions at the micrometer and nanometer length scales to be a viable technology for MEMS fabrication. Compared to traditional MEMS processes that rely heavily on expensive equipment and time-consuming steps, direct-write additive manufacturing techniques allow for rapid design-to-prototype realization by limiting or circumventing the need for cleanrooms, photolithography and extensive training. With current direct-write additive

Boehmite-An Efficient and Recyclable Acid-Base Bifunctional Catalyst for Aldol Condensation Reaction.

Science.gov (United States)

Reshma, P C Rajan; Vikneshvaran, Sekar; Velmathi, Sivan

2018-06-01

In this work boehmite was used as an acid-base bifunctional catalyst for aldol condensation reactions of aromatic aldehydes and ketones. The catalyst was prepared by simple sol-gel method using Al(NO3)3·9H2O and NH4OH as precursors. The catalyst has been characterized by X-ray diffraction (XRD), Fourier Transform Infrared (FTIR), Scanning Electron Microscopy (SEM), UV-visible spectroscopy (DRS), BET surface area analyses. Boehmite is successfully applied as catalyst for the condensation reaction between 4-nitrobenzaldehyde and acetone as a model substrate giving α, β-unsaturated ketones without any side product. The scope of the reaction is extended for various substituted aldehydes. A probable mechanism has been suggested to explain the cooperative behavior of the acidic and basic sites. The catalyst is environmentally friendly and easily recovered from the reaction mixture. Also the catalyst is reusable up to 3 catalytic cycles.

21 CFR 172.5 - General provisions for direct food additives.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true General provisions for direct food additives. 172.5... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION General Provisions § 172.5 General provisions for direct food additives. (a...

Catalytic Routes for the Conversion of Biomass Derivatives to Hydrocarbons and/or Platform Chemicals

Energy Technology Data Exchange (ETDEWEB)

Silks, III, Louis A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-10-07

Unprotected carbohydrates were reacted in amine-catalyzed cascade reactions with various methyl ketones to give a direct access to C-glycosides by an operationally simple protocol. As the reaction mechanism,an aldol condensation followed by an intramolecular conjugate addition is assumed.

EncM, a versatile enterocin biosynthetic enzyme involved in Favorskii oxidative rearrangement, aldol condensation, and heterocycle-forming reactions

Science.gov (United States)

Xiang, Longkuan; Kalaitzis, John A.; Moore, Bradley S.

2004-01-01

The bacteriostatic natural product enterocin from the marine microbe “Streptomyces maritimus” has an unprecedented carbon skeleton that is derived from an aromatic polyketide biosynthetic pathway. Its caged tricyclic, nonaromatic core is derived from a linear poly-β-ketide precursor that formally undergoes a Favorskii-like oxidative rearrangement. In vivo characterization of the gene encM through mutagenesis and heterologous biosynthesis demonstrated that its protein product not only is solely responsible for the oxidative C—C rearrangement, but also facilitates two aldol condensations plus two heterocycle forming reactions. In total, at least five chiral centers and four rings are generated by this multifaceted flavoprotein. Heterologous expression of the enterocin biosynthesis genes encABCDLMN in Streptomyces lividans resulted in the formation of the rearranged metabolite desmethyl-5-deoxyenterocin and the shunt products wailupemycins D-G. Addition of the methyltransferase gene encK, which was previously proposed through mutagenesis to additionally assist EncM in the Favorskii rearrangement, shifted the production to the O-methyl derivative 5-deoxyenterocin. The O-methyltransferase EncK seems to be specific for the pyrone ring of enterocin, because bicyclic polyketides bearing pyrone rings are not methylated in vivo. Expression of encM with different combinations of homologous actinorhodin biosynthesis genes did not result in the production of oxidatively rearranged enterocin-actinorhodin hybrid compounds as anticipated, suggesting that wild-type EncM may be specific for its endogenous type II polyketide synthase or for benzoyl-primed polyketide precursors. PMID:15505225

One-pot aldol condensation and hydrodeoxygenation of biomass-derived carbonyl compounds for biodiesel synthesis.

Science.gov (United States)

Faba, Laura; Díaz, Eva; Ordóñez, Salvador

2014-10-01

Integrating reaction steps is of key interest in the development of processes for transforming lignocellulosic materials into drop-in fuels. We propose a procedure for performing the aldol condensation (reaction between furfural and acetone is taken as model reaction) and the total hydrodeoxygenation of the resulting condensation adducts in one step, yielding n-alkanes. Different combinations of catalysts (bifunctional catalysts or mechanical mixtures), reaction conditions, and solvents (aqueous and organic) have been tested for performing these reactions in an isothermal batch reactor. The results suggest that the use of bifunctional catalysts and aqueous phase lead to an effective integration of both reactions. Therefore, selectivities to n-alkanes higher than 50% were obtained using this catalyst at typical hydrogenation conditions (T=493 K, P=4.5 MPa, 24 h reaction time). The use of organic solvent, carbonaceous supports, or mechanical mixtures of monofunctional catalysts leads to poorer results owing to side effects; mainly, hydrogenation of reactants and adsorption processes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

76 FR 41687 - Food Additives Permitted for Direct Addition to Food for Human Consumption; Hydroxypropyl Cellulose

Science.gov (United States)

2011-07-15

... Organization and the World Health Organization (FAO/WHO) Expert Committee for Food Additives (JECFA) has... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 172 [Docket No. FDA-2010-F-0103] Food Additives Permitted for Direct Addition to Food for Human Consumption...

Peculiar behavior of MWW materials in aldol condensation of furfural and acetone.

Science.gov (United States)

Kikhtyanin, Oleg; Chlubná, Pavla; Jindrová, Tereza; Kubička, David

2014-07-21

MWW family of different structural types (MCM-22, MCM-49, MCM-56 and MCM-36) was used as catalysts for aldol condensation of furfural and acetone studied in a batch reactor at 100 °C, autogenous pressure and a reaction time of 0-4 h. To establish a relation between physico-chemical and catalytic properties of microporous materials, the samples were characterized by XRD, SEM, N2 adsorption, FTIR and TGA. It was found that the acidic solids possessed appreciable activity in the reaction and resulted in the formation of products of aldehyde-ketone interaction. Surprisingly, MCM-22 and MCM-49, i.e. three-dimensional materials containing internal supercages, exhibited higher activity than two MCM-36 catalysts with two-dimensional character having larger accessible external surface area due to expansion of the interlayer space by swelling and pillaring treatments. Moreover, all MWW family catalysts gave higher conversion than the large-pore zeolite BEA. Nevertheless, furfural conversion decreased rapidly for all the studied materials due to coke formation. Unexpectedly, the deactivation was found to be more severe for MCM-36 catalysts than for MCM-22 and MCM-49, which was attributed to the reaction taking place also in supercages that are protected by 10-ring channels from severe coking. In contrast the cups located on the external surface were coked rapidly.

Mechanochemically synthesized LiAlOx catalyst for aqueous aldol condensation of furfural with acetone

Directory of Open Access Journals (Sweden)

Stepanova L. N.

2017-10-01

Full Text Available In the present study, the mechanochemical method is proposed for synthesis of LiAl-layered double hydroxides (LDHs. This method is eco-friendly and allows obtaining LiAl-LDH under relatively mild conditions (centripetal acceleration of milling bodies 300 m s-2 and in a short period of time (15 minutes. The structures of as-prepared LiAl-LDH, LiAl-mixed oxide (calcined LDH and “activated” LiAl-LDH obtained after rehydration of the corresponding mixed oxide were confirmed by X-ray diffraction. The basicity of LiAlOx was measured by temperature-programmed desorption of CO2 and double isotherm technique. According to data obtained, LiAl-mixed oxide has a significant higher carbon dioxide adsorption capacity compared to MgAlmixed oxides prepared by conventional co-precipitation method. This indicates a large amount of basic surface sites with different strength (strong, medium and weak for Li-containing systems. The formation of “activated” LiAl-LDH having Bronsted basic sites (OH groups in the interlayer space provides an increased catalytic activity of LiAlOx in the reaction of aqueous-phase aldol condensation between furfural and acetone.

Direct observation of lubricant additives using tomography techniques

Energy Technology Data Exchange (ETDEWEB)

Chen, Yunyun [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Sanchez, Carlos [Mechanical Engineering, Texas A& M University, College Station, Texas 77843 (United States); Parkinson, Dilworth Y. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Liang, Hong, E-mail: hliang@tamu.edu [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Mechanical Engineering, Texas A& M University, College Station, Texas 77843 (United States)

2016-07-25

Lubricants play important roles in daily activities such as driving, walking, and cooking. The current understanding of mechanisms of lubrication, particularly in mechanical systems, has been limited by the lack of capability in direct observation. Here, we report an in situ approach to directly observe the motion of additive particles in grease under the influence of shear. Using the K-edge tomography technique, it is possible to detect particular additives in a grease and observe their distribution through 3D visualization. A commercial grease as a reference was studied with and without an inorganic additive of Fe{sub 3}O{sub 4} microparticles. The results showed that it was possible to identify these particles and track their movement. Under a shear stress, Fe{sub 3}O{sub 4} particles were found to adhere to the edge of calcium complex thickeners commonly used in grease. Due to sliding, the grease formed a film with increased density. This approach enables in-line monitoring of a lubricant and future investigation in mechanisms of lubrication.

The effect of the distance between acidic site and basic site immobilized on mesoporous solid on the activity in catalyzing aldol condensation

Science.gov (United States)

Yu, Xiaofang; Yu, Xiaobo; Wu, Shujie; Liu, Bo; Liu, Heng; Guan, Jingqi; Kan, Qiubin

2011-02-01

Acid-base bifunctional heterogeneous catalysts containing carboxylic and amine groups, which were immobilized at defined distance from one another on the mesoporous solid were synthesized by immobilizing lysine onto carboxyl-SBA-15. The obtained materials were characterized by X-ray diffraction (XRD), N 2 adsorption, Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), scanning electron micrographs (SEM), transmission electron micrographs (TEM), elemental analysis, and back titration. Proximal-C-A-SBA-15 with a proximal acid-base distance was more active than maximum-C-A-SBA-15 with a maximum acid-base distance in aldol condensation reaction between acetone and various aldehydes. It appears that the distance between acidic site and basic site immobilized on mesoporous solid should be an essential factor for catalysis optimization.

Amine-catalyzed direct aldol reactions of hydroxy- and dihydroxyacetone: biomimetic synthesis of carbohydrates.

Science.gov (United States)

Popik, Oskar; Pasternak-Suder, Monika; Leśniak, Katarzyna; Jawiczuk, Magdalena; Górecki, Marcin; Frelek, Jadwiga; Mlynarski, Jacek

2014-06-20

This article presents comprehensive studies on the application of primary, secondary, and tertiary amines as efficient organocatalysts for the de novo synthesis of ketoses and deoxyketoses. Mimicking the actions of aldolase enzymes, the synthesis of selected carbohydrates was accomplished in aqueous media by using proline- and serine-based organocatalysts. The presented methodology also provides direct access to unnatural L-carbohydrates from the (S)-glyceraldehyde precursor. Determination of the absolute configuration of all obtained sugars was feasible using a methodology consisting of concerted ECD and VCD spectroscopy.

Sensitivity of directed networks to the addition and pruning of edges and vertices

Science.gov (United States)

Goltsev, A. V.; Timár, G.; Mendes, J. F. F.

2017-08-01

Directed networks have various topologically different extensive components, in contrast to a single giant component in undirected networks. We study the sensitivity (response) of the sizes of these extensive components in directed complex networks to the addition and pruning of edges and vertices. We introduce the susceptibility, which quantifies this sensitivity. We show that topologically different parts of a directed network have different sensitivity to the addition and pruning of edges and vertices and, therefore, they are characterized by different susceptibilities. These susceptibilities diverge at the critical point of the directed percolation transition, signaling the appearance (or disappearance) of the giant strongly connected component in the infinite size limit. We demonstrate this behavior in randomly damaged real and synthetic directed complex networks, such as the World Wide Web, Twitter, the Caenorhabditis elegans neural network, directed Erdős-Rényi graphs, and others. We reveal a nonmonotonic dependence of the sensitivity to random pruning of edges or vertices in the case of C. elegans and Twitter that manifests specific structural peculiarities of these networks. We propose the measurements of the susceptibilities during the addition or pruning of edges and vertices as a new method for studying structural peculiarities of directed networks.

Direct and Maternal Additive Effects on Rabbit Growth and Linear ...

African Journals Online (AJOL)

Growth and linear body measurements of rabbits which consisted of 17 ew Zealand White (ZW), 19 Chinchilla (CH), 29 ZW x CH and 33 CH x ZW kittens were compared. The aim of the experiment was to evaluate the crossbreeding effects (i.e direct and maternal additive effect) for growth (individual body weight, IBW) and ...

Direct Conversion of Cellulose into Ethyl Lactate in Supercritical Ethanol-Water Solutions.

Science.gov (United States)

Yang, Lisha; Yang, Xiaokun; Tian, Elli; Lin, Hongfei

2016-01-08

Biomass-derived ethyl lactate is a green solvent with a growing market as the replacement for petroleum-derived toxic organic solvents. Here we report, for the first time, the production of ethyl lactate directly from cellulose with the mesoporous Zr-SBA-15 silicate catalyst in a supercritical mixture of ethanol and water. The relatively strong Lewis and weak Brønsted acid sites on the catalyst, as well as the surface hydrophobicity, were beneficial to the reaction and led to synergy during consecutive reactions, such as depolymerization, retro-aldol condensation, and esterification. Under the optimum reaction conditions, ∼33 % yield of ethyl lactate was produced from cellulose with the Zr-SBA-15 catalyst at 260 °C in supercritical 95:5 (w/w) ethanol/water. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cost-effectiveness of additional catheter-directed thrombolysis for deep vein thrombosis

Science.gov (United States)

ENDEN, T.; RESCH, S.; WHITE, C.; WIK, H. S.; KLØW, N. E.; SANDSET, P. M.

2013-01-01

Summary Background Additional treatment with catheter-directed thrombolysis (CDT) has recently been shown to reduce post-thrombotic syndrome (PTS). Objectives To estimate the cost effectiveness of additional CDT compared with standard treatment alone. Methods Using a Markov decision model, we compared the two treatment strategies in patients with a high proximal deep vein thrombosis (DVT) and a low risk of bleeding. The model captured the development of PTS, recurrent venous thromboembolism and treatment-related adverse events within a lifetime horizon and the perspective of a third-party payer. Uncertainty was assessed with one-way and probabilistic sensitivity analyzes. Model inputs from the CaVenT study included PTS development, major bleeding from CDT and utilities for post DVT states including PTS. The remaining clinical inputs were obtained from the literature. Costs obtained from the CaVenT study, hospital accounts and the literature are expressed in US dollars ($); effects in quality adjusted life years (QALY). Results In base case analyzes, additional CDT accumulated 32.31 QALYs compared with 31.68 QALYs after standard treatment alone. Direct medical costs were $64 709 for additional CDT and $51 866 for standard treatment. The incremental cost-effectiveness ratio (ICER) was $20 429/QALY gained. One-way sensitivity analysis showed model sensitivity to the clinical efficacy of both strategies, but the ICER remained < $55 000/QALY over the full range of all parameters. The probability that CDT is cost effective was 82% at a willingness to pay threshold of $50 000/QALY gained. Conclusions Additional CDT is likely to be a cost-effective alternative to the standard treatment for patients with a high proximal DVT and a low risk of bleeding. PMID:23452204

Direct conversion of bio-ethanol to isobutene on nanosized Zn(x)Zr(y)O(z) mixed oxides with balanced acid-base sites.

Science.gov (United States)

Sun, Junming; Zhu, Kake; Gao, Feng; Wang, Chongmin; Liu, Jun; Peden, Charles H F; Wang, Yong

2011-07-27

We report the design and synthesis of nanosized Zn(x)Zr(y)O(z) mixed oxides for direct and high-yield conversion of bio-ethanol to isobutene (~83%). ZnO is addded to ZrO(2) to selectively passivate zirconia's strong Lewis acidic sites and weaken Brönsted acidic sites, while simultaneously introducing basicity. As a result, the undesired reactions of bio-ethanol dehydration and acetone polymerization/coking are suppressed. Instead, a surface basic site-catalyzed ethanol dehydrogenation to acetaldehyde, acetaldehyde to acetone conversion via a complex pathway including aldol-condensation/dehydrogenation, and a Brönsted acidic site-catalyzed acetone-to-isobutene reaction pathway dominates on the nanosized Zn(x)Zr(y)O(z) mixed oxide catalyst, leading to a highly selective process for direct conversion of bio-ethanol to isobutene.

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone

Directory of Open Access Journals (Sweden)

Oleg Kikhtyanin

2018-05-01

Full Text Available MgGa layered double hydroxides (Mg/Ga = 2–4 were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH3-TPD, CO2-TPD, SEM, and DRIFT and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO2-TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO2-TPD curve was attributed to the decomposition of carbonates newly formed by CO2 interaction with interlayer carbonates rather than to CO2 desorption from basic sites. Accordingly, CO2-TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone.

Science.gov (United States)

Kikhtyanin, Oleg; Čapek, Libor; Tišler, Zdeněk; Velvarská, Romana; Panasewicz, Adriana; Diblíková, Petra; Kubička, David

2018-01-01

MgGa layered double hydroxides (Mg/Ga = 2-4) were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH 3 -TPD, CO 2 -TPD, SEM, and DRIFT) and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO 2 -TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO 2 -TPD curve was attributed to the decomposition of carbonates newly formed by CO 2 interaction with interlayer carbonates rather than to CO 2 desorption from basic sites. Accordingly, CO 2 -TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had practically

Calibration-free absolute frequency response measurement of directly modulated lasers based on additional modulation.

Science.gov (United States)

Zhang, Shangjian; Zou, Xinhai; Wang, Heng; Zhang, Yali; Lu, Rongguo; Liu, Yong

2015-10-15

A calibration-free electrical method is proposed for measuring the absolute frequency response of directly modulated semiconductor lasers based on additional modulation. The method achieves the electrical domain measurement of the modulation index of directly modulated lasers without the need for correcting the responsivity fluctuation in the photodetection. Moreover, it doubles measuring frequency range by setting a specific frequency relationship between the direct and additional modulation. Both the absolute and relative frequency response of semiconductor lasers are experimentally measured from the electrical spectrum of the twice-modulated optical signal, and the measured results are compared to those obtained with conventional methods to check the consistency. The proposed method provides calibration-free and accurate measurement for high-speed semiconductor lasers with high-resolution electrical spectrum analysis.

The Reduction of Nitriles to Aldehydes: Applications of Raney Nickel ...

African Journals Online (AJOL)

NJD

The selective reduction of a nitrile to an aldehyde, especially when the substrate ..... prelude to reductive amination chemistry was thwarted by a rapid aldol ... and allowed the direct incorporation of the α-methylbenzylamine chiral auxiliary.

Advanced Methods for Direct Ink Write Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Compel, W. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lewicki, J. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2018-01-24

Lawrence Livermore National Laboratory is one of the world’s premier labs for research and development of additive manufacturing processes. Out of these many processes, direct ink write (DIW) is arguably one of the most relevant for the manufacture of architected polymeric materials, components and hardware. However, a bottleneck in this pipeline that has largely been ignored to date is the lack of advanced software implementation with respect to toolpath execution. There remains to be a convenient, automated method to design and produce complex parts that is user-friendly and enabling for the realization of next generation designs and structures. For a material to be suitable as a DIW ink it must possess the appropriate rheological properties for this process. Most importantly, the material must exhibit shear-thinning in order to extrude through a print head and have a rapid recovery of its static shear modulus. This makes it possible for the extrudate to be self-supporting upon exiting the print head. While this and other prerequisites narrow the scope of ‘offthe- shelf’ printable materials directly amenable to DIW, the process still tolerates a wide range of potential feedstock materials. These include metallic alloys, inorganic solvent borne dispersions, polymeric melts, filler stabilized monomer compositions, pre-elastomeric feedstocks and thermoset resins each of which requires custom print conditions tailored to the individual ink. As such, an ink perfectly suited for DIW may be prematurely determined to be undesirable for the process if printed under the wrong conditions. Defining appropriate print conditions such as extrusion rate, layer height, and maximum bridge length is a vital first step in validating an ink’s DIW capability.

Estimation of direct effects for survival data by using the Aalen additive hazards model

DEFF Research Database (Denmark)

Martinussen, Torben; Vansteelandt, Stijn; Gerster, Mette

2011-01-01

We extend the definition of the controlled direct effect of a point exposure on a survival outcome, other than through some given, time-fixed intermediate variable, to the additive hazard scale. We propose two-stage estimators for this effect when the exposure is dichotomous and randomly assigned...... Aalen's additive regression for the event time, given exposure, intermediate variable and confounders. The second stage involves applying Aalen's additive model, given the exposure alone, to a modified stochastic process (i.e. a modification of the observed counting process based on the first...

Direct enantioselective conjugate addition of carboxylic acids with chiral lithium amides as traceless auxiliaries.

Science.gov (United States)

Lu, Ping; Jackson, Jeffrey J; Eickhoff, John A; Zakarian, Armen

2015-01-21

Michael addition is a premier synthetic method for carbon-carbon and carbon-heteroatom bond formation. Using chiral dilithium amides as traceless auxiliaries, we report the direct enantioselective Michael addition of carboxylic acids. A free carboxyl group in the product provides versatility for further functionalization, and the chiral reagent can be readily recovered by extraction with aqueous acid. The method has been applied in the enantioselective total synthesis of the purported structure of pulveraven B.

Feasibility of using Big Area Additive Manufacturing to Directly Manufacture Boat Molds

Energy Technology Data Exchange (ETDEWEB)

Post, Brian K. [ORNL; Chesser, Phillip C. [ORNL; Lind, Randall F. [ORNL; Sallas, Matthew R. [ORNL; Love, Lonnie J. [ORNL

2018-01-01

The goal of this project was to explore the feasibility of using Big Area Additive Manufacturing (BAAM) to directly manufacture a boat mold without the need for coatings. All prior tooling projects with BAAM required the use to thick coatings to overcome the surface finish limitations of the BAAM process. While the BAAM process significantly lowers the cost of building the mold, the high cost element rapidly became the coatings (cost of the material, labor on coating, and finishing). As an example, the time and cost to manufacture the molds for the Wind Turbine project with TPI Composites Inc. and the molds for the submarine project with Carderock Naval Warfare Systems was a fraction of the time and cost of the coatings. For this project, a catamaran boat hull mold was designed, manufactured, and assembled with an additional 0.15” thickness of material on all mold surfaces. After printing, the mold was immediately machined and assembled. Alliance MG, LLC (AMG), the industry partner of this project, experimented with mold release agents on the carbon-fiber reinforced acrylonitrile butadiene styrene (CF ABS) to verify that the material can be directly used as a mold (rather than needing a coating). In addition, for large molds (such as the wind turbine mold with TPI Composites Inc.), the mold only provided the target surface. A steel subframe had to be manufactured to provide structural integrity. If successful, this will significantly reduce the time and cost necessary for manufacturing large resin infusion molds using the BAAM process.

Engineering Neurospora crassa for cellobionate production directly from cellulose without any enzyme addition

Science.gov (United States)

A previously engineered strain of N. crassa F5'ace-1'cre-1'ndvB) with six out of seven ß-glucosidase (bgl) genes, two transcription factors (cre1 and ace-1) and cellobionate phosphorylase (ndvB) deleted was able to produce cellobiose and cellobionate directly from cellulose without the addition of e...

Direct Enantioselective Conjugate Addition of Carboxylic Acids with Chiral Lithium Amides as Traceless Auxiliaries

Science.gov (United States)

2016-01-01

Michael addition is a premier synthetic method for carbon–carbon and carbon–heteroatom bond formation. Using chiral dilithium amides as traceless auxiliaries, we report the direct enantioselective Michael addition of carboxylic acids. A free carboxyl group in the product provides versatility for further functionalization, and the chiral reagent can be readily recovered by extraction with aqueous acid. The method has been applied in the enantioselective total synthesis of the purported structure of pulveraven B. PMID:25562717

Independent and additive repetition priming of motion direction and color in visual search.

Science.gov (United States)

Kristjánsson, Arni

2009-03-01

Priming of visual search for Gabor patch stimuli, varying in color and local drift direction, was investigated. The task relevance of each feature varied between the different experimental conditions compared. When the target defining dimension was color, a large effect of color repetition was seen as well as a smaller effect of the repetition of motion direction. The opposite priming pattern was seen when motion direction defined the target--the effect of motion direction repetition was this time larger than for color repetition. Finally, when neither was task relevant, and the target defining dimension was the spatial frequency of the Gabor patch, priming was seen for repetition of both color and motion direction, but the effects were smaller than in the previous two conditions. These results show that features do not necessarily have to be task relevant for priming to occur. There is little interaction between priming following repetition of color and motion, these two features show independent and additive priming effects, most likely reflecting that the two features are processed at separate processing sites in the nervous system, consistent with previous findings from neuropsychology & neurophysiology. The implications of the findings for theoretical accounts of priming in visual search are discussed.

77 FR 71695 - Secondary Direct Food Additives Permitted in Food for Human Consumption; Sodium...

Science.gov (United States)

2012-12-04

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 173 [Docket No. FDA-2011-F-0853] Secondary Direct Food Additives Permitted in Food for Human Consumption; Sodium... dodecylbenzenesulfonate (CAS No. 25155-30-0) as an antimicrobial agent for use in wash water for fruits and vegetables...

Tandem ring-closing metathesis/isomerization reactions for the total synthesis of violacein

DEFF Research Database (Denmark)

Petersen, Mette Terp; Nielsen, Thomas Eiland

2013-01-01

A series of 5-substituted 2-pyrrolidinones was synthesized through a one-pot ruthenium alkylidene-catalyzed tandem RCM/isomerization/nucleophilic addition sequence. The intermediates resulting from RCM/isomerization showed reactivity toward electrophiles in aldol condensation reactions which...

Ketone Body Acetoacetate Buffers Methylglyoxal via a Non-enzymatic Conversion during Diabetic and Dietary Ketosis

DEFF Research Database (Denmark)

Salomon, Trine; Sibbersen, Christian; Hansen, Jakob

2017-01-01

now demonstrate that during ketosis, another meta- bolic route is operative via direct non-enzymatic aldol reaction between methylglyoxal and the ke- tone body acetoacetate, leading to 3-hydroxyhex- ane-2,5-dione. This novel metabolite is present at a concentration of 10%–20% of the methylglyoxal...

Characterization of additive manufacturing processes for polymer micro parts productions using direct light processing (DLP) method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

The process capability of additive manufacturing (AM) for direct production of miniaturized polymer components with micro features is analyzed in this work. The consideration of the minimum printable feature size and obtainable tolerances of AM process is a critical step to establish a process...... chains for the production of parts with micro scale features. A specifically designed direct light processing (DLP) AM machine suitable for precision printing has been used. A test part is designed having features with different sizes and aspect ratios in order to evaluate the DLP AM machine capability...

Preparation and characterization of Mg-Zr mixed oxide aerogels and their application as aldol condensation catalysts.

Science.gov (United States)

Sádaba, Irantzu; Ojeda, Manuel; Mariscal, Rafael; Richards, Ryan; López Granados, Manuel

2012-10-08

A series of Mg-Zr mixed oxides with different nominal Mg/(Mg+Zr) atomic ratios, namely 0, 0.1, 0.2, 0.4, 0.85, and 1, is prepared by alcogel methodology and fundamental insights into the phases obtained and resulting active sites are studied. Characterization is performed by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, N(2) adsorption-desorption isotherms, and thermal and chemical analysis. Cubic Mg(x)Zr(1-x)O(2-x) solid solution, which results from the dissolution of Mg(2+) cations within the cubic ZrO(2) structure, is the main phase detected for the solids with theoretical Mg/(Mg+Zr) atomic ratio ≤0.4. In contrast, the cubic periclase (c-MgO) phase derived from hydroxynitrates or hydroxy precursors predominates in the solid with Mg/(Mg+Zr)=0.85. c-MgO is also incipiently detected in samples with Mg/(Mg+Zr)=0.2 and 0.4, but in these solids the c-MgO phase mostly arises from the segregation of Mg atoms out of the alcogel-derived c-Mg(x)Zr(1-x)O(2-x) phase during the calcination process, and therefore the species c-MgO and c-Mg(x)Zr(1-x)O(2-x) are in close contact. Regarding the intrinsic activity in furfural-acetone aldol condensation in the aqueous phase, these Mg-O-Zr sites located at the interface between c-Mg(x)Zr(1-x)O(2-x) and segregated c-MgO display a much larger intrinsic activity than the other noninterface sites that are present in these catalysts: Mg-O-Mg sites on c-MgO and Mg-O-Zr sites on c-Mg(x)Zr(1-x)O(2-x). The very active Mg-O-Zr sites rapidly deactivate in the furfural-acetone condensation due to the leaching of active phases, deposition of heavy hydrocarbonaceous compounds, and hydration of the c-MgO phase. Nonetheless, these Mg-Zr materials with very high specific surface areas would be suitable solid catalysts for other relevant reactions catalyzed by strong basic sites in nonaqueous environments. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of novel chromeno-annulated cis-fused pyrano[3,4-c]benzopyran and naphtho pyran derivatives via domino aldol-type/hetero Diels-Alder reaction and their cytotoxicity evaluation.

Science.gov (United States)

Madda, Jyothi; Venkatesham, Akkaladevi; Naveen Kumar, Bejjanki; Nagaiah, Kommu; Sujitha, Pombala; Ganesh Kumar, C; Rao, Tadikamalla Prabhakar; Jagadeesh Babu, Nanubolu

2014-09-15

New chromeno-annulated cis-fused pyrano[3,4-c]benzopyran and naphtho pyran derivatives have been synthesized by domino aldol-type reaction/hetero Diels-Alder reaction generated from o-quinone methide in situ from 7-O-prenyl derivatives of 8-formyl-2,3-disubstituted chromenones with resorcinols/naphthols in the presence of 20 mol% ethylenediamine diacetate (EDDA), triethylamine (2 mL) as co-catalyst in CH3CN under reflux conditions in good yields. The structures were established based on spectroscopic data, and further confirmed by X-ray diffraction analysis. The results showed that compounds 4h and 4j exhibited very potent cytotoxicity against human cervical cancer cell line (HeLa). Compound 4h displayed good inhibitory activity against both breast cancer cell lines, MDA-MB-231 and MCF-7. Further, the compound 4i exhibited good cytotoxicity against only MDA-MB-231, and compound 4j showed promising activity against human lung cancer cell line, A549 with IC50 value of 2.53±0.07 μM, which was comparable to the standard doxorubicin (IC50=1.21±0.1 μM). Copyright © 2014 Elsevier Ltd. All rights reserved.

Atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry of friction modifier additives analyzed directly from base oil solutions.

Science.gov (United States)

Widder, Lukas; Brennerb, Josef; Huttera, Herbert

2014-01-01

To develop new products and to apply measures of quality control quick and simple accessibility of additive composition in automo- tive lubrication is important. The aim of this study was to investigate the possibility of analyzing organic friction modifier additives by means of atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry [AP-MALDI-MS] from lubricant solu- tions without the use of additional separation techniques. Analyses of selected friction modifier ethoxylated tallow amines and oleic acid amide were compared using two ionization methods, positive-ion electrospray ionization (ESI) and AP-MALDI, using a LTQ Orbitrap mass spectrometer. Pure additives were characterized from solvent solutions, as well as from synthetic and mineral base oil mixtures. Detected ions of pure additive samples consisted mainly of [M + H]+, but also alkaLi metal adducts [M + Na]+ and [M + K]+ could be seen. Characterizations of blends of both friction modifiers from the base oil mixtures were carried out as well and showed significant inten- sities for several additive peaks. Thus, this work shows a method to directly analyze friction modifier additives used in the automotive industry from an oil blend via the use of AP-MALDI without any further separation steps. The method presented will further simplify the acquisition of data on lubricant composition and additives. Furthermore, it allows the perspective of analyzing additive reaction products directly from formulated oil blends.

An Ionic Liquid Solution of Chitosan as Organocatalyst

Directory of Open Access Journals (Sweden)

René Wilhelm

2013-11-01

Full Text Available Chitosan, which is derived from the biopolymer chitin, can be readily dissolved in different ionic liquids. The resulting homogeneous solutions were applied in an asymmetric Aldol reaction. Depending on the type of ionic liquid used, high asymmetric inductions were found. The influence of different additives was also studied. The best results were obtained in [BMIM][Br] without an additive.

Direct fabrication of bio-inspired gecko-like geometries with vat polymerization additive manufacturing method

DEFF Research Database (Denmark)

Davoudinejad, A.; M. Ribo, M.; Pedersen, D. B.

2018-01-01

on. The geometry and fabrication of these surfaces are still under research. In this study, the feasibility of using direct fabrication of microscale features by Additive Manufacturing (AM) processes was investigated. The investigation was carried out using a specifically designed vat...... photopolymerization AM machine-tool suitable for precision manufacturing at the micro dimensional scale which has previously been developed, built and validated at the Technical University of Denmark. It was shown that it was possible to replicate a simplified surface inspired by the Tokay gecko, the geometry...

One-pot conversion of biomass-derived xylose and furfural into levulinate esters via acid catalysis.

Science.gov (United States)

Hu, Xun; Jiang, Shengjuan; Wu, Liping; Wang, Shuai; Li, Chun-Zhu

2017-03-07

Direct conversion of biomass-derived xylose and furfural into levulinic acid, a platform molecule, via acid-catalysis has been accomplished for the first time in dimethoxymethane/methanol. Dimethoxymethane acted as an electrophile to transform furfural into 5-hydroxymethylfurfural (HMF). Methanol suppressed both the polymerisation of the sugars/furans and the Aldol condensation of levulinic acid/ester.

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

A new class of organocatalysts involving a primary amine as the only functional group is developed for catalytic asymmetric aldol reaction of cyclohexanone/ cyclopentanone with various aryl aldehydes in thepresence of benzoic acid as an additive at −10◦C. In an unexpected observation, the primary amine catalyzed ...

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

An efficient synthesis of (-)-wodeshiol 1 is described. The key reactions include highly stereoselective aldol condensation of piperonal with the dianion of chiral oxazolidinone, subsequent intramolecular ring cyclization of the aldol product 8 and a diastereocontrolled oxygenation of dilactone 7 in good yield.

Structural Mass Saving Potential of a 5-MW Direct-Drive Generator Designed for Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Fingersh, Lee J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dykes, Katherine L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hayes, Austin [Rochester Institute of Technology

2017-11-09

As wind turbine blade diameters and tower height increase to capture more energy in the wind, higher structural loads results in more structural support material increasing the cost of scaling. Weight reductions in the generator transfer to overall cost savings of the system. Additive manufacturing facilitates a design-for-functionality approach, thereby removing traditional manufacturing constraints and labor costs. The most feasible additive manufacturing technology identified for large, direct-drive generators in this study is powder-binder jetting of a sand cast mold. A parametric finite element analysis optimization study is performed, optimizing for mass and deformation. Also, topology optimization is employed for each parameter-optimized design.The optimized U-beam spoked web design results in a 24 percent reduction in structural mass of the rotor and 60 percent reduction in radial deflection.

Effects of Saccharomyces cerevisiae at direct addition or pre-incubation on in vitro gas production kinetics and degradability of four fibrous feeds

Directory of Open Access Journals (Sweden)

Mona M.Y. Elghandour

2014-04-01

Full Text Available The objective of this study was to evaluate the effects of Saccharomyces cerevisiae on in vitro gas production (GP kinetics and degradability of corn stover, oat straw, sugarcane bagasse and sorghum straw. Feedstuffs were incubated with different doses of yeast [0, 4, 8 and 12 mg/g dry matter (DM] at direct addition or 72 h pre-incubation. Rumen GP was recorded at 2, 4, 6, 8, 10, 12, 14, 24, 30, 48, 54 and 72 h of incubation. After 72 h, rumen pH and methane were determined and contents were filtrated for DM, neutral (NDF and acid detergent fibre (ADF degradability. Fibrous species×method of application×yeast interactions occurred (P<0.001 for all measured ruminal GP parameters and degradability. The direct addition or 72 h pre-incubation of S. cerevisiae with corn stover improved (P<0.05 GP and methane and decreased (P<0.05 the lag time (L and NDF degradability (NDFD. The direct addition of S. cerevisiae to oat straw increased (P<0.05 rate of GP (c and decreased (P<0.05 asymptotic GP (b. However, 72 h pre-incubation increased (P<0.05 c with linearly decreased b, DM degradability (DMD and NDFD. Applying S. cerevisiae for 72 h pre-incubation decreased (P<0.001 methane emission. The direct addition or 72 h pre-incubation of S. cerevisiae to sorghum straw increased (P<0.05 b, c, L, DMD and NDFD. Overall, the effect of dose varied among different feedstuffs and different application methods. Results suggested that the direct addition of S. cerevisiae could support and improve ruminal fermentation of lowquality forages at 4 to 12 g/kg DM.

Influence of additional heat exchanger block on directional solidification system for growing multi-crystalline silicon ingot - A simulation investigation

Science.gov (United States)

Nagarajan, S. G.; Srinivasan, M.; Aravinth, K.; Ramasamy, P.

2018-04-01

Transient simulation has been carried out for analyzing the heat transfer properties of Directional Solidification (DS) furnace. The simulation results revealed that the additional heat exchanger block under the bottom insulation on the DS furnace has enhanced the control of solidification of the silicon melt. Controlled Heat extraction rate during the solidification of silicon melt is requisite for growing good quality ingots which has been achieved by the additional heat exchanger block. As an additional heat exchanger block, the water circulating plate has been placed under the bottom insulation. The heat flux analysis of DS system and the temperature distribution studies of grown ingot confirm that the established additional heat exchanger block on the DS system gives additional benefit to the mc-Si ingot.

76 FR 16285 - Food Additives Permitted for Direct Addition to Food for Human Consumption; Bacteriophage...

Science.gov (United States)

2011-03-23

... mammalian cells. (See discussion at 71 FR 47729 at 47730). As such, traditional animal testing of the... 51758 at 51759, August 25, 2000). Suitability relates to the effectiveness of the ingredient in... additive be shown to be safe prior to marketing. Under Sec. 170.3(i), a food additive is ``safe'' if...

Studies towards the synthesis of radiolabeled R106-1(LY295337)

International Nuclear Information System (INIS)

Rodriguez, M.J.; Zweifel, M.J.

1996-01-01

A unique semisynthetic pathway has been used as a route to acquire radiolabeled material of a complex natural product, R106. The retro-aldol reaction of R106-1 gave a key intermediate R106-sarcosine that was used in a subsequent aldol reaction to incorporate acetone--[2- 14 C]. (author)

Determination of metal impurities in MOX powder by direct current arc atomic emission spectroscopy. Application of standard addition method for direct analysis of powder sample

International Nuclear Information System (INIS)

Furuse, Takahiro; Taguchi, Shigeo; Kuno, Takehiko; Surugaya, Naoki

2016-12-01

Metal impurities in MOX powder obtained from uranium and plutonium recovered from reprocessing process of spent nuclear fuel have to be determined for its characterization. Direct current arc atomic emission spectroscopy (DCA-AES) is one of the useful methods for direct analysis of powder sample without dissolving the analyte into aqueous solution. However, the selection of standard material, which can overcome concerns such as matrix matching, is quite important to create adequate calibration curves for DCA-AES. In this study, we apply standard addition method using the certified U_3O_8 containing known amounts of metal impurities to avoid the matrix problems. The proposed method provides good results for determination of Fe, Cr and Ni contained in MOX samples at a significant quantity level. (author)

Food Additives Permitted for Direct Addition to Food for Human Consumption; Folic Acid. Final rule.

Science.gov (United States)

2016-04-15

The Food and Drug Administration (FDA or we) is amending the food additive regulations to provide for the safe use of folic acid in corn masa flour. We are taking this action in response to a food additive petition filed jointly by Gruma Corporation, Spina Bifida Association, March of Dimes Foundation, American Academy of Pediatrics, Royal DSM N.V., and National Council of La Raza.

Multicomponent Synthesis of Isoindolinone Frameworks via RhIII -Catalysed in situ Directing Group-Assisted Tandem Oxidative Olefination/Michael Addition.

Science.gov (United States)

Wang, Liang; Liu, Xi; Liu, Jian-Biao; Shen, Jun; Chen, Qun; He, Ming-Yang

2018-04-04

A Rh III -catalysed three-component synthesis of isoindolinone frameworks via direct assembly of benzoyl chlorides, o-aminophenols and activated alkenes has been developed. The process involves in situ generation of o-aminophenol (OAP)-based bidentate directing group (DG), Rh III -catalysed tandem ortho C-H olefination and subsequent cyclization via aza-Michael addition. This protocol exhibits good chemoselectivity and functional group tolerance. Computational studies showed that the presence of hydroxyl group on the N-aryl ring could enhance the chemoselectivity of the reaction. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Environmentally friendly paint and varnish additives based on isobutyrate aldehyde condensation products

Science.gov (United States)

Guziałowska-Tic, Joanna; Jan Tic, Wilhelm

2017-10-01

The demand for exploitation of new plasticizers and coalescents to be used for production of water dispersion adhesives based on poli(vinyl acetate), turned to be recently of particular significance because the use of all kind of toxic phthalates was banned and certain restrictions were made to use glycol derivatives classified as volatile organic compounds. An alternative for toxic plasticizers used for production of adhesives is hydroxyester (HE-1) obtained from isobutanal during the process of aldol condensation under subsequent Cannizaro and Tischenko reactions. The paper presents selected results of ecotoxicological tests on the environmental impact of hydroxyester HE-1. It was found that the substance is biodegradable and has no negative impact on algae growth rate, however it may inhibit algae biomass growth. The results of Daphnia immobilization test shows that the substance is safe for the aquatic environment. Whereas, at higher concentrations, hydroxyester HE-1 may exhibit acute toxicity to rainbow trout.

A Comparative Study of Basic, Amphoteric, and Acidic Catalysts in the Oxidative Coupling of Methanol and Ethanol for Acrolein Production.

Science.gov (United States)

Lilić, Aleksandra; Wei, Tiantian; Bennici, Simona; Devaux, Jean-François; Dubois, Jean-Luc; Auroux, Aline

2017-09-11

The impact of acid/base properties (determined by adsorption microcalorimetry) of various catalysts on the cross-aldolization of acetaldehyde and formaldehyde leading to acrolein was methodically studied in oxidizing conditions starting from a mixture of methanol and ethanol. The aldol condensation and further dehydration to acrolein were carried out on catalysts presenting various acid/base properties (MgO, Mg-Al oxides, Mg/SiO 2 , NbP, and heteropolyanions on silica, HPA/SiO 2 ). Thermodynamic calculations revealed that cross-aldolization is always favored compared with self-aldolization of acetaldehyde, which leads to crotonaldehyde formation. The presence of strong basic sites is shown to be necessary, but a too high amount drastically increases CO x production. On strong acid sites, production of acrolein and carbon oxides (CO x ) does not increase with temperature. The optimal catalyst for this process should be amphoteric with a balanced acid/base cooperation of medium strength sites and a small amount (150 kJ mol -1 ). © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of trace boron addition on the directional solidification characteristics of Ti-6Al-4V

International Nuclear Information System (INIS)

Srinivasan, Raghavan; Tamirisakandala, Sesh

2010-01-01

Trace boron addition to several titanium alloys results in a reduction in the as-cast grain size by an order of magnitude. TiB needles are observed along the prior beta grain boundaries and not the grain interior in these alloys, indicating that TiB needles are not sites for the heterogeneous nucleation of beta grains. This study seeks to understand the influence of the growth rate R on microstructure evolution and grain refinement in Ti-6Al-4V-0.1B alloy using directional solidification experiments and microstructural characterization.

Assessing direct analysis in real-time-mass spectrometry (DART-MS) for the rapid identification of additives in food packaging.

Science.gov (United States)

Ackerman, L K; Noonan, G O; Begley, T H

2009-12-01

The ambient ionization technique direct analysis in real time (DART) was characterized and evaluated for the screening of food packaging for the presence of packaging additives using a benchtop mass spectrometer (MS). Approximate optimum conditions were determined for 13 common food-packaging additives, including plasticizers, anti-oxidants, colorants, grease-proofers, and ultraviolet light stabilizers. Method sensitivity and linearity were evaluated using solutions and characterized polymer samples. Additionally, the response of a model additive (di-ethyl-hexyl-phthalate) was examined across a range of sample positions, DART, and MS conditions (temperature, voltage and helium flow). Under optimal conditions, molecular ion (M+H+) was the major ion for most additives. Additive responses were highly sensitive to sample and DART source orientation, as well as to DART flow rates, temperatures, and MS inlet voltages, respectively. DART-MS response was neither consistently linear nor quantitative in this setting, and sensitivity varied by additive. All additives studied were rapidly identified in multiple food-packaging materials by DART-MS/MS, suggesting this technique can be used to screen food packaging rapidly. However, method sensitivity and quantitation requires further study and improvement.

Cyclopentanone: A raw material for production of C15 and C17 fuel precursors

International Nuclear Information System (INIS)

Hronec, Milan; Fulajtárova, Katarína; Liptaj, Tibor; Štolcová, Magdaléna; Prónayová, Naďa; Soták, Tomáš

2014-01-01

The synthesis of diesel or jet fuels intermediates from furfural or 5-hydroxymethylfurfural (HMF) via aqueous aldol-condensation with cyclopentanone was studied. Cyclopentanone is the product of furfural rearrangement in an aqueous system. Since the aldol-condensation reaction is conducted in an aqueous solution all these biomass-derived reactants can be applied as water solutions formed in the processes of their preparation. The aldol condensation of furfural with cyclopentanone is at low concentration of base and molar ratio of reactants 2:1 highly selective and after 40–80 min of reaction at a temperature of 40–100 °C more than 95 mol% yield of 2,5-bis (2-furylmethylidene) cyclopentan-1-one (F 2 C) was obtained. When instead of furfural as a reactant HMF was used higher than 98 mol% yield of 2,5-bis (5-hydroxymethyl-2-furylmethylidene) cyclopentan-1-one was achieved. The final products of aldol condensation of furfural and HMF are exclusively corresponding dimers, what enables to obtain after subsequent hydrogenation/hydrodeoxygenation step dialkylcyclopentane type of diesel or jet fuels having C 15 or C 17 molecules. - Highlights: • The aldol condensation of biomass derived cyclopentanone with furfural and HMF. • More than 95 mol % yields of products are achieved. • The products are compounds having exclusively 15 or 17 carbon atoms in molecule. • Reactants can be used as diluted aqueous solutions. • The products are separated as solids insoluble in water

Catalytic Upgrading of 5-Hydroxymethylfurfural to Drop-in Biofuels by Solid Base and Bifunctional Metal-Acid Catalysts.

Science.gov (United States)

Bohre, Ashish; Saha, Basudeb; Abu-Omar, Mahdi M

2015-12-07

Design and synthesis of effective heterogeneous catalysts for the conversion of biomass intermediates into long chain hydrocarbon precursors and their subsequent deoxygenation to hydrocarbons is a viable strategy for upgrading lignocellulose into distillate range drop-in biofuels. Herein, we report a two-step process for upgrading 5-hydroxymethylfurfural (HMF) to C9 and C11 fuels with high yield and selectivity. The first step involves aldol condensation of HMF and acetone with a water tolerant solid base catalyst, zirconium carbonate (Zr(CO3 )x ), which gave 92 % C9 -aldol product with high selectivity at nearly 100 % HMF conversion. The as-synthesised Zr(CO3 )x was analysed by several analytical methods for elucidating its structural properties. Recyclability studies of Zr(CO3 )x revealed a negligible loss of its activity after five consecutive cycles over 120 h of operation. Isolated aldol product from the first step was hydrodeoxygenated with a bifunctional Pd/Zeolite-β catalyst in ethanol, which showed quantitative conversion of the aldol product to n-nonane and 1-ethoxynonane with 40 and 56 % selectivity, respectively. 1-Ethoxynonane, a low oxygenate diesel range fuel, which we report for the first time in this paper, is believed to form through etherification of the hydroxymethyl group of the aldol product with ethanol followed by opening of the furan ring and hydrodeoxygenation of the ether intermediate. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cobalt Oxide Porous Nanofibers Directly Grown on Conductive Substrate as a Binder/Additive-Free Lithium-Ion Battery Anode with High Capacity.

Science.gov (United States)

Liu, Hao; Zheng, Zheng; Chen, Bochao; Liao, Libing; Wang, Xina

2017-12-01

In order to reduce the amount of inactive materials, such as binders and carbon additives in battery electrode, porous cobalt monoxide nanofibers were directly grown on conductive substrate as a binder/additive-free lithium-ion battery anode. This electrode exhibited very high specific discharging/charging capacities at various rates and good cycling stability. It was promising as high capacity anode materials for lithium-ion battery.

Symptom burden and job absenteeism after treatment with additional catheter-directed thrombolysis for deep vein thrombosis

Directory of Open Access Journals (Sweden)

Enden T

2013-09-01

Full Text Available Tone Enden,1–3 Nils-Einar Kløw,2,3 Per Morten Sandset1,3 1Department of Hematology, Oslo University Hospital, Oslo, Norway; 2Department of Radiology and Nuclear Medicine, Oslo University Hospital, Oslo, Norway; 3Institute of Clinical Medicine, University of Oslo, Oslo, Norway Introduction: Additional catheter-directed thrombolysis (CDT for acute deep vein thrombosis (DVT reduces long-term postthrombotic syndrome and is likely to represent a cost-effective alternative treatment compared to the standard treatment of anticoagulation and elastic compression stockings. Accelerated thrombus resolution has also been suggested to improve symptoms and patient function in the acute phase. We aimed to investigate whether additional CDT led to fewer symptoms and job absenteeism during the first 6 months after initiation of DVT treatment compared to standard treatment alone. Methods: The Catheter-directed Venous Thrombolysis (CaVenT study was a multicenter open label, randomized controlled trial of patients ages 18 years to 75 years with a verified high proximal DVT,<21 days of symptoms, and no apparent bleeding risk. Patients were allocated to additional CDT or to standard treatment only. Symptoms were assessed at baseline and at 6 months using items from the generic and disease-specific quality of life questionnaires EQ-5D and VEINES-QOL/Sym, respectively. Individual data on sickness benefits related to venous thromboembolic disease were obtained from the national welfare service. Results: A total of 90 patients allocated additional CDT and 99 control patients completed long-term follow-up and were included in the analyses. Twenty-four in the CDT arm and 40 controls received sick leave (P = 0.046. When considering working patients only (54 in the CDT arm and 72 controls this difference was no longer statistically significant. Mean duration of job absenteeism was 86.4 days (95% confidence interval 59.4–113.5 in the CDT arm and 60.1 days (95% confidence

Complex chemical composition of colored surface films formed from reactions of propanal in sulfuric acid at upper troposphere/lower stratosphere aerosol acidities.

Science.gov (United States)

Van Wyngarden, A L; Pérez-Montaño, S; Bui, J V H; Li, E S W; Nelson, T E; Ha, K T; Leong, L; Iraci, L T

Particles in the upper troposphere and lower stratosphere (UT/LS) consist mostly of concentrated sulfuric acid (40-80 wt %) in water. However, airborne measurements have shown that these particles also contain a significant fraction of organic compounds of unknown chemical composition. Acid-catalyzed reactions of carbonyl species are believed to be responsible for significant transfer of gas phase organic species into tropospheric aerosols and are potentially more important at the high acidities characteristic of UT/LS particles. In this study, experiments combining sulfuric acid (H 2 SO 4 ) with propanal and with mixtures of propanal with glyoxal and/or methylglyoxal at acidities typical of UT/LS aerosols produced highly colored surface films (and solutions) that may have implications for aerosol properties. In order to identify the chemical processes responsible for the formation of the surface films, attenuated total reflectance-Fourier transform infrared (ATR-FTIR) and 1 H nuclear magnetic resonance (NMR) spectroscopies were used to analyze the chemical composition of the films. Films formed from propanal were a complex mixture of aldol condensation products, acetals and propanal itself. The major aldol condensation products were the dimer (2-methyl-2-pentenal) and 1,3,5-trimethylbenzene that was formed by cyclization of the linear aldol condensation trimer. Additionally, the strong visible absorption of the films indicates that higher-order aldol condensation products must also be present as minor species. The major acetal species were 2,4,6-triethyl-1,3,5-trioxane and longer-chain linear polyacetals which are likely to separate from the aqueous phase. Films formed on mixtures of propanal with glyoxal and/or methylglyoxal also showed evidence of products of cross-reactions. Since cross-reactions would be more likely than self-reactions under atmospheric conditions, similar reactions of aldehydes like propanal with common aerosol organic species like glyoxal

Comparison of sugar molecule decomposition through glucose and fructose: a high-level quantum chemical study.

Energy Technology Data Exchange (ETDEWEB)

Assary, R. S.; Curtiss, L. A. (Center for Nanoscale Materials); ( MSD); (Northwestern Univ.)

2012-02-01

Efficient chemical conversion of biomass is essential to produce sustainable energy and industrial chemicals. Industrial level conversion of glucose to useful chemicals, such as furfural, hydroxymethylfurfural, and levulinic acid, is a major step in the biomass conversion but is difficult because of the formation of undesired products and side reactions. To understand the molecular level reaction mechanisms involved in the decomposition of glucose and fructose, we have carried out high-level quantum chemical calculations [Gaussian-4 (G4) theory]. Selective 1,2-dehydration, keto-enol tautomerization, isomerization, retro-aldol condensation, and hydride shifts of glucose and fructose molecules were investigated. Detailed kinetic and thermodynamic analyses indicate that, for acyclic glucose and fructose molecules, the dehydration and isomerization require larger activation barriers compared to the retro-aldol reaction at 298 K in neutral medium. The retro-aldol reaction results in the formation of C2 and C4 species from glucose and C3 species from fructose. The formation of the most stable C3 species, dihydroxyacetone from fructose, is thermodynamically downhill. The 1,3-hydride shift leads to the cleavage of the C-C bond in the acyclic species; however, the enthalpy of activation is significantly higher (50-55 kcal/mol) than that of the retro-aldol reaction (38 kcal/mol) mainly because of the sterically hindered distorted four-membered transition state compared to the hexa-membered transition state in the retro-aldol reaction. Both tautomerization and dehydration are catalyzed by a water molecule in aqueous medium; however, water has little effect on the retro-aldol reaction. Isomerization of glucose to fructose and glyceraldehyde to dihydroxyacetone proceeds through hydride shifts that require an activation enthalpy of about 40 kcal/mol at 298 K in water medium. This investigation maps out accurate energetics of the decomposition of glucose and fructose molecules

Protein conjugated with aldehydes derived from lipid peroxidation as an independent parameter of the carbonyl stress in the kidney damage

Directory of Open Access Journals (Sweden)

Medina-Navarro Rafael

2011-11-01

Full Text Available Abstract Background One of the well-defined and characterized protein modifications usually produced by oxidation is carbonylation, an irreversible non-enzymatic modification of proteins. However, carbonyl groups can be introduced into proteins by non-oxidative mechanisms. Reactive carbonyl compounds have been observed to have increased in patients with renal failure. In the present work we have described a procedure designed as aldehyde capture to calculate the protein carbonyl stress derived solely from lipid peroxidation. Methods Acrolein-albumin adduct was prepared as standard at alkaline pH. Rat liver microsomal membranes and serum samples from patients with diabetic nephropathy were subjected to the aldehyde capture procedure and aldol-protein formation. Before alkalinization and incubation, samples were precipitated and redisolved in 6M guanidine. The absorbances of the samples were read with a spectrophotometer at 266 nm against a blank of guanidine. Results Evidence showed abundance of unsaturated aldehydes derived from lipid peroxidation in rat liver microsomal membranes and in the serum of diabetic patients with advanced chronic kidney disease. Carbonyl protein and aldol-proteins resulted higher in the diabetic nephropathy patients (p Conclusion The aldehyde-protein adduct represents a non oxidative component of carbonyl stress, independent of the direct amino acid oxidation and could constitute a practical and novelty strategy to measure the carbonyl stress derived solely from lipid peroxidation and particularly in diabetic nephropathy patients. In addition, we are in a position to propose an alternative explanation of why alkalinization of urine attenuates rhabdomyolysis-induced renal dysfunction.

An In-Depth Review on Direct Additive Manufacturing of Metals

Science.gov (United States)

Azam, Farooq I.; Rani, Ahmad Majdi Abdul; Altaf, Khurram; Rao, T. V. V. L. N.; Aimi Zaharin, Haizum

2018-03-01

Additive manufacturing (AM), also known as 3D Printing, is a revolutionary manufacturing technique which has been developing rapidly in the last 30 years. The evolution of this precision manufacturing process from rapid prototyping to ready-to-use parts has significantly alleviated manufacturing constraints and design freedom has been outstandingly widened. AM is a non-conventional manufacturing technique which utilizes a 3D CAD model data to build parts by adding one material layer at a time, rather than removing it and fulfills the demand for manufacturing parts with complex geometric shapes, great dimensional accuracy, and easy to assemble parts. Additive manufacturing of metals has become the area of extensive research, progressing towards the production of final products and replacing conventional manufacturing methods. This paper provides an insight to the available metal additive manufacturing technologies that can be used to produce end user products without using conventional manufacturing methods. The paper also includes the comparison of mechanical and physical properties of parts produced by AM with the parts manufactured using conventional processes.

The reaction of organocerium reagents with easily enolizable ketones

International Nuclear Information System (INIS)

Imamoto, Tsuneo; Kusumoto, Tetsuo; Sugiura, Yasushi; Suzuki, Nobuyo; Takiyama, Nobuyuki

1985-01-01

Organocerium (III) reagents were conveniently generated by the reaction of organolithium compounds with anhydrous cerium (III) chloride. The reagents are less basic than organolithiums and Grignard reagents, and they react readily at -78 deg C with easily enolizable ketones such as 2-tetralone to afford addition products in high yields. Cerium (III) enolates were also generated from lithium enolates and cerium (III) chloride. The cerium (III) enolates undergo aldol addition with ketones or sterically crowded aldehyde to give the corresponding β-hydroxy ketones in good to high yields. (author)

Nonenzymatic gluconeogenesis-like formation of fructose 1,6-bisphosphate in ice.

Science.gov (United States)

Messner, Christoph B; Driscoll, Paul C; Piedrafita, Gabriel; De Volder, Michael F L; Ralser, Markus

2017-07-11

The evolutionary origins of metabolism, in particular the emergence of the sugar phosphates that constitute glycolysis, the pentose phosphate pathway, and the RNA and DNA backbone, are largely unknown. In cells, a major source of glucose and the large sugar phosphates is gluconeogenesis. This ancient anabolic pathway (re-)builds carbon bonds as cleaved in glycolysis in an aldol condensation of the unstable catabolites glyceraldehyde 3-phosphate and dihydroxyacetone phosphate, forming the much more stable fructose 1,6-bisphosphate. We here report the discovery of a nonenzymatic counterpart to this reaction. The in-ice nonenzymatic aldol addition leads to the continuous accumulation of fructose 1,6-bisphosphate in a permanently frozen solution as followed over months. Moreover, the in-ice reaction is accelerated by simple amino acids, in particular glycine and lysine. Revealing that gluconeogenesis may be of nonenzymatic origin, our results shed light on how glucose anabolism could have emerged in early life forms. Furthermore, the amino acid acceleration of a key cellular anabolic reaction may indicate a link between prebiotic chemistry and the nature of the first metabolic enzymes.

[Development of boomerang-type intramolecular cascade reactions and application to natural product synthesis].

Science.gov (United States)

Takasu, K

2001-12-01

Intramolecular cascade reaction has received much attention as a powerful methodology to construct a polycyclic framework in organic synthesis. We have been developing "boomerang-type cascade reaction" to construct a variety of polycyclic skeletons efficiently. In the above reactions, a nucleophilic function of substrates changes the character into an electrophile after the initial reaction, and the electrophilic group acts as a nucleophile in the second reaction. That is, the reaction center stepwise moves from one functional group back to the same one via other functional groups. The stream of the electron concerning the cascade reaction is like a locus of boomerang. We show here three different boomerang-type reactions via ionic species or free radicals. 1) Diastereoselective Michael-aldol reaction based on the chiral auxiliary method and enantioselective Michael-aldol reaction by the use of external chiral sources. 2) Short and efficient total syntheses of longifolane sesquiterpenes utilizing intramolecular double Michael addition as a key step. 3) Development of boomerang-type radical cascade reaction of halopolyenes to construct terpenoid skeletons and its regioselectivity.

Asymmetric Total Synthesis of Ieodomycin B

Directory of Open Access Journals (Sweden)

Shuangjie Lin

2017-01-01

Full Text Available Ieodomycin B, which shows in vitro antimicrobial activity, was isolated from a marine Bacillus species. A novel asymmetric total synthetic approach to ieodomycin B using commercially available geraniol was achieved. The approach involves the generation of 1,3-trans-dihydroxyl at C-3 and C-5 positions via a Crimmins-modified Evans aldol reaction and a chelation-controlled Mukaiyama aldol reaction of a p-methoxybenzyl-protected aldehyde, as well as the generation of a lactone ring in a deprotection–lactonization one-pot reaction.

Effect of rare earth oxide addition on microstructures of ultra-fine WC-Co particulate reinforced Cu matrix composites prepared by direct laser sintering

International Nuclear Information System (INIS)

Gu Dongdong; Shen Yifu; Zhao Long; Xiao Jun; Wu Peng; Zhu Yongbing

2007-01-01

This paper presents a detailed investigation into the influence of the rare earth (RE) oxide (La 2 O 3 ) addition upon the densification and the resultant microstructural characteristics of the submicron WC-Co particulate reinforced Cu matrix composites prepared by direct laser sintering. It is found that the relative density of the laser sintered sample with 1 wt.% La 2 O 3 addition increased by 11.5% as compared with the sample without RE addition. The addition of RE element favored the microstructural refinement and improved the particulate dispersion homogeneity and the particulate/matrix interfacial coherence. The metallurgical functions of the RE element in improving the sinterability were also addressed. It shows that due to the unique properties of RE element such as high surface activity and large atomic radius, the addition of trace RE element can decrease the surface tension of the melt, resist the grain growth coarsening and increase the heterogeneous nucleation rate during laser sintering

Tin-Containing Silicates: Identification of a Glycolytic Pathway via 3-Deoxyglucosone

DEFF Research Database (Denmark)

Tolborg, Søren; Meier, Sebastian; Sádaba, I.

2016-01-01

a cascade of four to five sequential steps. Currently, there is a limited understanding of the competing glycolytic pathways within these systems. Here we identify dehydration of glucose to 3-deoxyglucosone as an important pathway that occurs in addition to retro-aldol reaction of hexoses when using tin......-containing silicates. It is possible to influence the relative carbon flux through these pathways by controlling the amount of alkali metal salts present in the reaction mixture. In the absence of added potassium carbonate, at least 15–30% carbon flux via 3-deoxyglucosone is observed. Addition of just a few ppm...

Breaking the Dogma of Aldolase Specificity: Simple Aliphatic Ketones and Aldehydes are Nucleophiles for Fructose-6-phosphate Aldolase.

Science.gov (United States)

Roldán, Raquel; Sanchez-Moreno, Israel; Scheidt, Thomas; Hélaine, Virgil; Lemaire, Marielle; Parella, Teodor; Clapés, Pere; Fessner, Wolf-Dieter; Guérard-Hélaine, Christine

2017-04-11

d-Fructose-6-phosphate aldolase (FSA) was probed for extended nucleophile promiscuity by using a series of fluorogenic substrates to reveal retro-aldol activity. Four nucleophiles ethanal, propanone, butanone, and cyclopentanone were subsequently confirmed to be non-natural substrates in the synthesis direction using the wild-type enzyme and its D6H variant. This exceptional widening of the nucleophile substrate scope offers a rapid entry, in good yields and high stereoselectivity, to less oxygenated alkyl ketones and aldehydes, which was hitherto impossible. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Direct Democracy

DEFF Research Database (Denmark)

Beramendi, Virginia; Ellis, Andrew; Kaufman, Bruno

While many books on direct democracy have a regional or national approach, or simply focus on one of the many mechanisms associated with direct democracy, this Handbook delves into a global comparison of direct democracy mechanisms, including referendums, citizens' initiatives, agenda initiatives...... learned. In addition, the uniquely comprehensive world survey outlines direct democracy provisions in 214 countries and territories and indicates which, if any, of these provisions are used by each country or territory at both the national and sub-national levels. Furthermore, the world survey includes...

Additives In Meat and Poultry Products

Science.gov (United States)

... Fact Sheets / Additives in Meat and Poultry Products / Additives in Meat and Poultry Products Z7_0Q0619C0JGR010IFST1G5B10H3 ... Affairs Recalls and Public Health Alerts Regulatory Compliance Regulations, Directives and Notices Rulemaking ...

The influence of the speed of the down-ward leader channel in computation of additional charge for protection against direct lightning strike by charge transfer system in 'ultra-corona' mode

International Nuclear Information System (INIS)

Talevski, V.

2012-01-01

In this paper computation of additional charge is done for protection against direct lightning strike, by charge transfer system, by point electrode, in 'ultra-corona' mode. The influence of the voltage increase in a very small time interval is computed and the influence is taken into consideration in the computation of the additional space charge on the object used for protection. The model of the electrical thundercloud is taken into consideration with all the electrical charge in it with its corresponding heights above ground. Plotted values are presented of the speed of the down-ward leader from the cloud versus the additional space charge, needed to be placed on the top of the object protected by direct lightning. Plotted values are also presented of different position of the horizontal distance of the protected object and its height versus the additional space charge. (Authors)

Sn-Beta catalysed conversion of hemicellulosic sugars

DEFF Research Database (Denmark)

Holm, Martin; Pagán-Torres, Yomaira J.; Shunmugavel, Saravanamurugan

2012-01-01

are observed for the pentoses. This finding is in accordance to a reaction pathway that involves the retro aldol condensation of the sugars to form a triose and glycolaldehyde for the pentoses, and two trioses for hexoses. When reacting glycolaldehyde (formally a C2-sugar) in the presence of Sn-Beta, aldol...... condensation occurs, leading to the formation of methyl lactate, methyl vinylglycolate and methyl 2-hydroxy-4-methoxybutanoate. In contrast, when converting the sugars in water at low temperatures (100 °C), Sn-Beta catalyses the isomerisation of sugars (ketose–aldose epimers), rather than the formation...

Use of fused deposit modeling for additive manufacturing in hospital facilities: European certification directives.

Science.gov (United States)

Otero, Joel J; Vijverman, An; Mommaerts, Maurice Y

2017-09-01

The goal of this study was to identify current European Union regulations governing hospital-based use of fused deposit modeling (FDM), as implemented via desktop three-dimensional (3D) printers. Literature and Internet sources were screened, searching for official documents, regulations/legislation, and views of specialized attorneys or consultants regarding European regulations for 3D printing or additive manufacturing (AM) in a healthcare facility. A detailed review of the latest amendment (2016) of the European Parliament and Council legislation for medical devices and its classification was performed, which has regularly updated published guidelines for medical devices, that are classified by type and duration of patient contact. As expected, regulations increase in accordance with the level (I-III) of classification. Custom-made medical devices are subject to different regulations than those controlling serially mass-produced items, as originally specified in 98/79/EC European Parliament and Council legislation (1993) and again recently amended (2016). Healthcare facilities undertaking in-house custom production are not obliged to fully follow the directives as stipulated, given an exception for this scenario (Article 4.4a, 98/79/EC). Patient treatment and diagnosis with the aid of customized 3D printing in a healthcare facility can be performed without fully meeting the European Parliament and Council legislation if the materials used are ISO 10993 certified and article 4.4a applies. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

Energy Technology Data Exchange (ETDEWEB)

Chen, Chuanmin [School of Environmental Science and Engineering, North China Electric Power University, Baoding 071003, Hebei Province (China); Zhuang, Ye [Energy and Environmental Research Center, University of North Dakota, 15 North 23rd Street, Grand Forks, ND 58203 (United States); Wang, Chunbo [Department of Power engineering, North China Electric Power University, Baoding 071003, Hebei Province (China)

2009-07-15

For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. (author)

Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

Energy Technology Data Exchange (ETDEWEB)

Chuanmin Chen; Ye Zhuang; Chunbo Wang [North China Electric Power University, Baoding (China). School of Environmental Science & Engineering

2009-07-15

For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. 33 refs., 7 figs., 2 tabs.

76 FR 11328 - Secondary Direct Food Additives Permitted in Food for Human Consumption

Science.gov (United States)

2011-03-02

... amending the food additive regulations to permit the use of hydrogen peroxide as an antimicrobial agent in... Group, 801 N. Orange Ave., suite 710, Orlando, FL 32801 filed a food additive petition (FAP 0A4781). The... as an antimicrobial agent in the manufacture of modified whey by ultrafiltration methods. In...

Experimental analysis on semi-finishing machining of Ti6Al4V additively manufactured by direct melting laser sintering

Science.gov (United States)

Imbrogno, Stano; Bordin, Alberto; Bruschi, Stefania; Umbrello, Domenico

2016-10-01

The Additive Manufacturing (AM) techniques are particularly appealing especially for titanium aerospace and biomedical components because they permit to achieve a strong reduction of the buy-to-fly ratio. However, finishing machining operations are often necessary to reduce the uneven surface roughness and geometrics because of local missing accuracy. This work shows the influence of the cutting parameters, cutting speed and feed rate, on the cutting forces as well as on the thermal field observed in the cutting zone, during a turning operation carried out on bars made of Ti6Al4V obtained by the AM process called Direct Metal Laser Sintering (DMLS). Moreover, the sub-surface microstructure alterations due to the process are also showed and commented.

Additive operator-difference schemes splitting schemes

CERN Document Server

Vabishchevich, Petr N

2013-01-01

Applied mathematical modeling isconcerned with solving unsteady problems. This bookshows how toconstruct additive difference schemes to solve approximately unsteady multi-dimensional problems for PDEs. Two classes of schemes are highlighted: methods of splitting with respect to spatial variables (alternating direction methods) and schemes of splitting into physical processes. Also regionally additive schemes (domain decomposition methods)and unconditionally stable additive schemes of multi-component splitting are considered for evolutionary equations of first and second order as well as for sy

24 CFR 235.1218 - Additional eligibility requirements.

Science.gov (United States)

2010-04-01

...; Direct Endorsement § 235.1218 Additional eligibility requirements. (a) Mortgage amount. It must be in an... par on one of the following dates, whichever rate is higher: (i) The date the Direct Endorsement mortgagee's underwriter signs the Mortgage Credit Analysis Worksheet (form HUD-92900 WS); or (ii) The date...

Influence of polymer additives on turbulent energy cascading in forced homogeneous isotropic turbulence studied by direct numerical simulations

International Nuclear Information System (INIS)

Li Feng-Chen; Cai Wei-Hua; Zhang Hong-Na; Wang Yue

2012-01-01

Direct numerical simulations (DNS) were performed for the forced homogeneous isotropic turbulence (FHIT) with/without polymer additives in order to elaborate the characteristics of the turbulent energy cascading influenced by drag-reducing effects. The finite elastic non-linear extensibility-Peterlin model (FENE-P) was used as the conformation tensor equation for the viscoelastic polymer solution. Detailed analyses of DNS data were carried out in this paper for the turbulence scaling law and the topological dynamics of FHIT as well as the important turbulent parameters, including turbulent kinetic energy spectra, enstrophy and strain, velocity structure function, small-scale intermittency, etc. A natural and straightforward definition for the drag reduction rate was also proposed for the drag-reducing FHIT based on the decrease degree of the turbulent kinetic energy. It was found that the turbulent energy cascading in the FHIT was greatly modified by the drag-reducing polymer additives. The enstrophy and the strain fields in the FHIT of the polymer solution were remarkably weakened as compared with their Newtonian counterparts. The small-scale vortices and the small-scale intermittency were all inhibited by the viscoelastic effects in the FHIT of the polymer solution. However, the scaling law in a fashion of extended self-similarity for the FHIT of the polymer solution, within the presently simulated range of Weissenberg numbers, had no distinct differences compared with that of the Newtonian fluid case

Modelling the role of intrinsic electric fields in microtubules as an additional control mechanism of bi-directional intracellular transport.

Science.gov (United States)

Sataric, M V; Budinski-Petkovic, L; Loncarevic, I; Tuszynski, J A

2008-01-01

Active transport is essential for cellular function, while impaired transport has been linked to diseases such as neuronal degeneration. Much long distance transport in cells uses opposite polarity molecular motors of the kinesin and dynein families to move cargos along microtubules. It is clear that many types of cargo are moved by both sets of motors, and frequently in a reverse direction. The general question of how the direction of transport is regulated is still open. The mechanism of the cell's differential control of diverse cargos within the same cytoplasmic background is still unclear as is the answer to the question how endosomes and mitochondria move to different locations within the same cell. To answer these questions we postulate the existence of a local signaling mechanism used by the cell to specifically control different cargos. In particular, we propose an additional physical mechanism that works through the use of constant and alternating intrinsic (endogenous) electric fields as a means of controlling the speed and direction of microtubule-based transport. A specific model is proposed and analyzed in this paper. The model involves the rotational degrees of freedom of the C-termini of tubulin, their interactions and the coupling between elastic and dielectric degrees of freedom. Viscosity of the solution is also included and the resultant equation of motion is found as a nonlinear elliptic equation with dissipation. A particular analytical solution of this equation is obtained in the form of a kink whose properties are analyzed. It is concluded that this solution can be modulated by the presence of electric fields and hence may correspond to the observed behavior of motor protein transport along microtubules.

Chiral metal-organic frameworks bearing free carboxylic acids for organocatalyst encapsulation.

Science.gov (United States)

Liu, Yan; Xi, Xiaobing; Ye, Chengcheng; Gong, Tengfei; Yang, Zhiwei; Cui, Yong

2014-12-08

Two chiral carboxylic acid functionalized micro- and mesoporous metal-organic frameworks (MOFs) are constructed by the stepwise assembly of triple-stranded heptametallic helicates with six carboxylic acid groups. The mesoporous MOF with permanent porosity functions as a host for encapsulation of an enantiopure organic amine catalyst by combining carboxylic acids and chiral amines in situ through acid-base interactions. The organocatalyst-loaded framework is shown to be an efficient and recyclable heterogeneous catalyst for the asymmetric direct aldol reactions with significantly enhanced stereoselectivity in relative to the homogeneous organocatalyst. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Application of Carbohydrate-Templated Asymmetric Diels-Alder Reaction to the Syntheses of ent-Penicillones A and B.

Science.gov (United States)

Weng, Chia-Hao; Hsu, Day-Shin; Liao, Chun-Chen

2016-11-18

Total syntheses of ent-penicillones A (ent-1) and B (ent-2) from 3,5-dimethylcatechol (3) were accomplished in 10 and 9 synthetic steps, respectively. A carbohydrate-templated asymmetric intramolecular Diels-Alder reaction of a masked o-benzoquinone (MOB) 9 and an aqueous acid-catalyzed intramolecular aldol reaction are the key synthetic steps. In addition, the absolute configurations of the bicyclo[2.2.2]oct-5-en-2-one core obtained from the per-O-benzylated α-d-glucopyranosyl as a carbohydrate template in the intramolecular Diels-Alder reaction of MOBs were revised.

New degradation compounds from lignocellulosic biomass pretreatment: routes for formation of potent oligophenolic enzyme inhibitors

DEFF Research Database (Denmark)

Rasmussen, H.; Tanner, David Ackland; Sørensen, H. R.

2017-01-01

-condensation reactions involving aldol condensations, 1,4 additions to α,β unsaturated carbonyl compounds, 3-keto acid decarboxylations and oxidations. Furthermore, pentose reactions with phenolic lignin components are suggested. The identification of the central role of xylose in the reaction routes for oligophenolic...... inhibitor formation led to the solution to protect the reactive anomeric center in xylose. It is shown that protection of the anomeric center in in situ generated xylose with ethylene glycol monobutyl ether, during pretreatment of wheat straw, reduces the level of oligophenols by 73%. The results pave...

Evolution of solidification texture during additive manufacturing

Science.gov (United States)

Wei, H. L.; Mazumder, J.; DebRoy, T.

2015-01-01

Striking differences in the solidification textures of a nickel based alloy owing to changes in laser scanning pattern during additive manufacturing are examined based on theory and experimental data. Understanding and controlling texture are important because it affects mechanical and chemical properties. Solidification texture depends on the local heat flow directions and competitive grain growth in one of the six preferred growth directions in face centered cubic alloys. Therefore, the heat flow directions are examined for various laser beam scanning patterns based on numerical modeling of heat transfer and fluid flow in three dimensions. Here we show that numerical modeling can not only provide a deeper understanding of the solidification growth patterns during the additive manufacturing, it also serves as a basis for customizing solidification textures which are important for properties and performance of components. PMID:26553246

Conversion of raw lignocellulosic biomass into branched long-chain alkanes through three tandem steps.

Science.gov (United States)

Li, Chunrui; Ding, Daqian; Xia, Qineng; Liu, Xiaohui; Wang, Yanqin

2016-07-07

Synthesis of branched long-chain alkanes from renewable biomass has attracted intensive interest in recent years, but the feedstock for this synthesis is restricted to platform chemicals. Here, we develop an effective and energy-efficient process to convert raw lignocellulosic biomass (e.g., corncob) into branched diesel-range alkanes through three tandem steps for the first time. Furfural and isopropyl levulinate (LA ester) were prepared from hemicellulose and cellulose fractions of corncob in toluene/water biphasic system with added isopropanol, which was followed by double aldol condensation of furfural with LA ester into C15 oxygenates and the final hydrodeoxygenation of C15 oxygenates into branched long-chain alkanes. The core point of this tandem process is the addition of isopropanol in the first step, which enables the spontaneous transfer of levulinic acid (LA) into the toluene phase in the form of LA ester through esterification, resulting in LA ester co-existing with furfural in the same phase, which is the basis for double aldol condensation in the toluene phase. Moreover, the acidic aqueous phase and toluene can be reused and the residues, including lignin and humins in aqueous phase, can be separated and carbonized to porous carbon materials. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The selective addition of water

NARCIS (Netherlands)

Resch, V.; Hanefeld, U.

2014-01-01

Water is omnipresent and essential. Yet at the same time it is a rather unreactive molecule. The direct addition of water to C[double bond, length as m-dash]C double bonds is therefore a challenge not answered convincingly. In this perspective we critically evaluate the selectivity and the

Anisotropic microstructure and superelasticity of additive manufactured NiTi alloy bulk builds using laser directed energy deposition

Energy Technology Data Exchange (ETDEWEB)

Bimber, Beth A. [Department of Engineering Science and Mechanics, The Pennsylvania State University, 212 Earth-Engineering Sciences Building, University Park, PA 16802 (United States); Hamilton, Reginald F., E-mail: rfh13@psu.edu [Department of Engineering Science and Mechanics, The Pennsylvania State University, 212 Earth-Engineering Sciences Building, University Park, PA 16802 (United States); Keist, Jayme; Palmer, Todd A. [Applied Research Laboratory, The Pennsylvania State University, State College, PA 16804 (United States)

2016-09-30

The microstructure and superelasticity in additive manufactured NiTi shape memory alloys (SMAs) were investigated. Using elementally blended Ni and Ti powder feedstock, Ni-rich build coupons were fabricated via the laser-based directed energy deposition (LDED) technique. The build volumes were large enough to extract tensile and compressive test specimens from selected locations for spatially resolving microconstituents and the underlying stress-induced martensitic phase transformation (SIMT) morphology. In the as-deposited condition, X-ray diffraction identified the B2 atomic crystal structure of the austenitic parent phase in NiTi SMAs, and Ni{sub 4}Ti{sub 3} precipitates were the predominant microconstituent identified through scanning electron microscopy. The microstructure exhibited anisotropy, which was characterized by the Ni{sub 4}Ti{sub 3} precipitate morphology being coarsest nearest the substrate, while a finer morphology was observed farthest from the substrate. In-situ full-field deformation measurements calculated using digital image correlation confirmed that the SIMT predominately occurred in the finer precipitate morphology. Heat treatment reduced the degree of anisotropy, and DIC analysis revealed localized SIMT strains increased compared to the as-deposited condition.

Evolution of the additive genetic variance–covariance matrix under continuous directional selection on a complex behavioural phenotype

Science.gov (United States)

Careau, Vincent; Wolak, Matthew E.; Carter, Patrick A.; Garland, Theodore

2015-01-01

Given the pace at which human-induced environmental changes occur, a pressing challenge is to determine the speed with which selection can drive evolutionary change. A key determinant of adaptive response to multivariate phenotypic selection is the additive genetic variance–covariance matrix (G). Yet knowledge of G in a population experiencing new or altered selection is not sufficient to predict selection response because G itself evolves in ways that are poorly understood. We experimentally evaluated changes in G when closely related behavioural traits experience continuous directional selection. We applied the genetic covariance tensor approach to a large dataset (n = 17 328 individuals) from a replicated, 31-generation artificial selection experiment that bred mice for voluntary wheel running on days 5 and 6 of a 6-day test. Selection on this subset of G induced proportional changes across the matrix for all 6 days of running behaviour within the first four generations. The changes in G induced by selection resulted in a fourfold slower-than-predicted rate of response to selection. Thus, selection exacerbated constraints within G and limited future adaptive response, a phenomenon that could have profound consequences for populations facing rapid environmental change. PMID:26582016

Evolution of the additive genetic variance-covariance matrix under continuous directional selection on a complex behavioural phenotype.

Science.gov (United States)

Careau, Vincent; Wolak, Matthew E; Carter, Patrick A; Garland, Theodore

2015-11-22

Given the pace at which human-induced environmental changes occur, a pressing challenge is to determine the speed with which selection can drive evolutionary change. A key determinant of adaptive response to multivariate phenotypic selection is the additive genetic variance-covariance matrix ( G: ). Yet knowledge of G: in a population experiencing new or altered selection is not sufficient to predict selection response because G: itself evolves in ways that are poorly understood. We experimentally evaluated changes in G: when closely related behavioural traits experience continuous directional selection. We applied the genetic covariance tensor approach to a large dataset (n = 17 328 individuals) from a replicated, 31-generation artificial selection experiment that bred mice for voluntary wheel running on days 5 and 6 of a 6-day test. Selection on this subset of G: induced proportional changes across the matrix for all 6 days of running behaviour within the first four generations. The changes in G: induced by selection resulted in a fourfold slower-than-predicted rate of response to selection. Thus, selection exacerbated constraints within G: and limited future adaptive response, a phenomenon that could have profound consequences for populations facing rapid environmental change. © 2015 The Author(s).

Solvent Isotope-induced Equilibrium Perturbation for Isocitrate Lyase

Science.gov (United States)

Quartararo, Christine E.; Hadi, Timin; Cahill, Sean M.; Blanchard, John S.

2014-01-01

Isocitrate lyase (ICL) catalyzes the reversible retro-aldol cleavage of isocitrate to generate glyoxylate and succinate. ICL is the first enzyme of the glyoxylate shunt, which allows for the anaplerosis of citric acid cycle intermediates under nutrient limiting conditions. In Mycobacterium tuberculosis, the source of ICL for these studies, ICL is vital for the persistence phase of the bacteria’s life cycle. Solvent kinetic isotope effects (KIEs) in the direction of isocitrate cleavage of D2OV = 2.0 ± 0.1 and D2O[V/Kisocitrate] = 2.2 ± 0.3 arise from the initial deprotonation of the C2 hydroxyl group of isocitrate or the protonation of the aci-acid of succinate product of the isocitrate aldol cleavage by a solvent-derived proton. This KIE suggested that an equilibrium mixture of all protiated isocitrate, glyoxylate and succinate prepared in D2O, would undergo transient changes in equilibrium concentrations as a result of the solvent KIE and solvent-derived deuterium incorporation into both succinate and isocitrate. No change in the isotopic composition of glyoxylate was expected or observed. We have directly monitored the changing concentrations of all isotopic species of all reactants and products using a combination of NMR spectroscopy and mass spectrometry. Continuous monitoring of glyoxylate by 1H NMR spectroscopy shows a clear equilibrium perturbation in D2O. The final equilibrium isotopic composition of reactants in D2O revealed di-deuterated succinate, protiated glyoxylate, and mono-deuterated isocitrate, with the transient appearance and disappearance of mono-deuterated succinate. A model for the equilibrium perturbation of substrate species, and their time-dependent isotopic composition is presented. PMID:24261638

Multiscale 3D manufacturing: combining thermal extrusion printing with additive and subtractive direct laser writing

Science.gov (United States)

Malinauskas, Mangirdas; Lukoševičius, Laurynas; MackevičiÅ«tÄ--, DovilÄ--; BalčiÅ«nas, Evaldas; RekštytÄ--, Sima; Paipulas, Domas

2014-05-01

A novel approach for efficient manufacturing of three-dimensional (3D) microstructured scaffolds designed for cell studies and tissue engineering applications is presented. A thermal extrusion (fused filament fabrication) 3D printer is employed as a simple and low-cost tabletop device enabling rapid materialization of CAD models out of biocompatible and biodegradable polylactic acid (PLA). Here it was used to produce cm- scale microporous (pore size varying from 100 to 400 µm) scaffolds. The fabricated objects were further laser processed in a direct laser writing (DLW) subtractive (ablation) and additive (lithography) manners. The first approach enables precise surface modification by creating micro-craters, holes and grooves thus increasing the surface roughness. An alternative way is to immerse the 3D PLA scaffold in a monomer solution and use the same DLW setup to refine its inner structure by fabricating dots, lines or a fine mesh on top as well as inside the pores of previously produced scaffolds. The DLW technique is empowered by ultrafast lasers - it allows 3D structuring with high spatial resolution in a great variety of photosensitive materials. Structure geometry on macro- to micro- scales could be finely tuned by combining these two fabrication techniques. Such artificial 3D substrates could be used for cell growth or as biocompatible-biodegradable implants. This combination of distinct material processing techniques enables rapid fabrication of diverse functional micro- featured and integrated devices. Hopefully, the proposed approach will find numerous applications in the field of ms, microfluidics, microoptics and many others.

Decisions Concerning Directional Dependence

Science.gov (United States)

von Eye, Alexander; DeShon, Richard P.

2012-01-01

In this rejoinder, von Eye and DeShon discuss the decision strategies proposed in their original article ("Directional Dependence in Developmental Research," this issue), as well as the ones proposed by the authors of the commentary (Pornprasertmanit and Little, "Determining Directional Dependency in Causal Associations," this issue). In addition,…

Effect of Additives on the Physicochemical and Drug Release ...

African Journals Online (AJOL)

Purpose: To prepare and evaluate spherical agglomerates of pioglitazone hydrochloride (PGH) for direct compression with different additives. Method: Spherical agglomerates of pioglitazone hydrochloride were prepared by emulsion solvent diffusion method with and without additives (polyethylene glycol 6000, polyvinyl ...

Metal Additive Manufacturing: A Review of Mechanical Properties

Science.gov (United States)

Lewandowski, John J.; Seifi, Mohsen

2016-07-01

This article reviews published data on the mechanical properties of additively manufactured metallic materials. The additive manufacturing techniques utilized to generate samples covered in this review include powder bed fusion (e.g., EBM, SLM, DMLS) and directed energy deposition (e.g., LENS, EBF3). Although only a limited number of metallic alloy systems are currently available for additive manufacturing (e.g., Ti-6Al-4V, TiAl, stainless steel, Inconel 625/718, and Al-Si-10Mg), the bulk of the published mechanical properties information has been generated on Ti-6Al-4V. However, summary tables for published mechanical properties and/or key figures are included for each of the alloys listed above, grouped by the additive technique used to generate the data. Published values for mechanical properties obtained from hardness, tension/compression, fracture toughness, fatigue crack growth, and high cycle fatigue are included for as-built, heat-treated, and/or HIP conditions, when available. The effects of test orientation/build direction on properties, when available, are also provided, along with discussion of the potential source(s) (e.g., texture, microstructure changes, defects) of anisotropy in properties. Recommendations for additional work are also provided.

Ruthenium-catalyzed self-coupling of primary and secondary alcohols with the liberation of dihydrogen

DEFF Research Database (Denmark)

Makarov, Ilya; Madsen, Robert

2013-01-01

The dehydrogenative self-condensation of primary and secondary alcohols has been studied in the presence of RuCl2(IiPr)(p-cymene). The conversion of primary alcohols into esters has been further optimized by using magnesium nitride as an additive, which allows the reaction to take place...... at a temperature and catalyst loading lower than those described previously. Secondary alcohols were dimerized into racemic ketones by a dehydrogenative Guerbet reaction with potassium hydroxide as the additive. The transformation gave good yields of the ketone dimers with a range of alkan-2-ols, whereas more...... substituted secondary alcohols were unreactive. The reaction proceeds by dehydrogenation to the ketone, followed by an aldol reaction and hydrogenation of the resulting enone. © 2013 American Chemical Society....

Histological and biomechanical analysis of porous additive manufactured implants made by direct metal laser sintering: a pilot study in sheep.

Science.gov (United States)

Stübinger, Stefan; Mosch, Isabel; Robotti, Pierfrancesco; Sidler, Michéle; Klein, Karina; Ferguson, Stephen J; von Rechenberg, Brigitte

2013-10-01

It was the aim of this study to analyze osseointegrative properties of porous additive manufactured titanium implants made by direct metal laser sintering in a sheep model after an implantation period of 2 and 8 weeks. Three different types of implants were placed in the pelvis of six sheep. In each sheep were placed three standard machined (M), three sandblasted and etched (SE), and three porous additive manufactured (AM) implants. Of these three implants (one per type) were examined histologically and six implants were tested biomechanically. Additionally a semiquantitative histomorphometrical and qualitative fluorescent microscopic analysis were performed. After 2 and 8 weeks bone-to-implant-contact (BIC) values of the AM surface (2w: 20.49% ± 5.18%; 8w: 43.91% ± 9.69%) revealed no statistical significant differences in comparison to the M (2w: 20.33% ± 11.50%; 8w: 25.33% ± 4.61%) and SE (2w: 43.67 ± 12.22%; 8w: 53.33 ± 8.96%) surfaces. AM surface showed the highest increase of the BIC between the two observation time points. Considering the same implantation period histomorphometry and fluorescent labelling disclosed no significant differences in the bone surrounding the three implants groups. In contrast Removal-torque-test showed a significant improve in fixation strength (P ≤ 0.001) for the AM (1891.82 ± 308, 44 Nmm) surface after eight weeks in comparison to the M (198.93±88,04 Nmm) and SE (730.08 ± 151,89 Nmm) surfaces. All three surfaces (M, SE, and AM) showed sound osseointegration. AM implants may offer a possible treatment option in clinics for patients with compromised bone situations. Copyright © 2013 Wiley Periodicals, Inc., a Wiley Company.

Freeze-dried formulation for direct 99mTc-labeling ior-egf/r3 MAb: additives, biodistribution, and stability

International Nuclear Information System (INIS)

Morales, Alejo A. Morales; Nunez-Gandolff, Gilda; Perez, Niuvis Perez; Veliz, Belkis Chico; Caballero-Torres, Idania; Duconge, Jorge; Fernandez, Eduardo; Crespo, Francisco Zayas; Veloso, Ana; Iznaga-Escobar, Normando

1999-01-01

Monoclonal antibodies (MAbs) have been useful for immunoscintigraphic applications in clinical diagnosis since they were introduced in nuclear medicine practice. The MAb ior egf/r3 developed at the Center of Molecular Immunology (Havana, Cuba) is a murine antibody that recognizes the human epidermal growth factor receptor (EGF-R) and has been used widely in the radioimmunodiagnosis of tumors of epithelial origin. Based on the direct Schwarz method, the present report describes the preparation of a freeze-dried formulation for radiolabeling the MAb ior egf/r3 with 99m Tc for immunoscintigraphic applications. Radiolabeling efficiency, effects on immunoreactivity, biodistribution, pharmacokinetic, and stability of the formulation are reported. The study demonstrated that the freeze-dried formulation can be labeled with 99m Tc at high yield. The resulting 99m Tc-labeled ior egf/r3 MAb can be used to visualize in vivo human tumors of epithelial origin by immunoscintigraphy studies. The kit does not need any other addition or purification at the time of tagging other than the requisite amount of pertechnetate (40-50 mCi). Because the contents of the kit are lyophilized, no special storage or transportation is required

Nitrogen turnover in fresh Douglas fir litter directly after additions of moisture and inorganic nitrogen

NARCIS (Netherlands)

Raat, K.J.; Tietema, A.; Verstraten, J.M.

2010-01-01

The effects of wetting and drying and inorganic nitrogen (N) addition on carbon (C) and N turnover in fresh Douglas fir litter (Speuld forest, the Netherlands) were investigated. Litter was incubated for 9 days in the laboratory, receiving different moisture and N addition treatments. Following the

77 FR 5201 - Ecolab, Inc.; Filing of Food Additive Petition

Science.gov (United States)

2012-02-02

.... FDA-2011-F-0853] Ecolab, Inc.; Filing of Food Additive Petition AGENCY: Food and Drug Administration... Ecolab, Inc., has filed a petition proposing that the food additive regulations be amended to provide for...-1390. The petition proposes to amend the food additive regulations in 21 CFR part 173, Secondary Direct...

7 CFR 766.112 - Additional security for restructured loans.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Additional security for restructured loans. 766.112..., DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS DIRECT LOAN SERVICING-SPECIAL Loan Servicing Programs § 766.112 Additional security for restructured loans. (a) If the borrower is delinquent prior to restructuring, the...

Evolution of genetic architecture under directional selection.

Science.gov (United States)

Hansen, Thomas F; Alvarez-Castro, José M; Carter, Ashley J R; Hermisson, Joachim; Wagner, Günter P

2006-08-01

We investigate the multilinear epistatic model under mutation-limited directional selection. We confirm previous results that only directional epistasis, in which genes on average reinforce or diminish each other's effects, contribute to the initial evolution of mutational effects. Thus, either canalization or decanalization can occur under directional selection, depending on whether positive or negative epistasis is prevalent. We then focus on the evolution of the epistatic coefficients themselves. In the absence of higher-order epistasis, positive pairwise epistasis will tend to weaken relative to additive effects, while negative pairwise epistasis will tend to become strengthened. Positive third-order epistasis will counteract these effects, while negative third-order epistasis will reinforce them. More generally, gene interactions of all orders have an inherent tendency for negative changes under directional selection, which can only be modified by higher-order directional epistasis. We identify three types of nonadditive quasi-equilibrium architectures that, although not strictly stable, can be maintained for an extended time: (1) nondirectional epistatic architectures; (2) canalized architectures with strong epistasis; and (3) near-additive architectures in which additive effects keep increasing relative to epistasis.

Studies on the Model Synthesis of the Brassinolide and Dolicholide Side Chains

Institute of Scientific and Technical Information of China (English)

Li Zeng PENG; Feng Zhi ZHANG; Tian Sheng MEI; Yu Lin LI

2003-01-01

A stereoselective synthesis of brassinolide and dolicholide, which involves constructionof the side chain enantiomers by a highly stereoselective aldol reaction of aldehyde 5 with theanion of α-silyloxy ketone 6 is described.

A CATALYTIC METHOD FOR THE SYNTHESIS OF 4-ALKYL(ARYL ...

African Journals Online (AJOL)

Preferred Customer

)-pyridinones and their 2-imino ... synthesis of milrinone analogues as a series of nonglycosidic, non-sympathomimetic, cardiotonic .... from dimethoxyacetophenone and ammonia adds to the aldol condensation product of the aldehyde and ...

High-performance ion mobility spectrometry with direct electrospray ionization (ESI-HPIMS) for the detection of additives and contaminants in food

International Nuclear Information System (INIS)

Midey, Anthony J.; Camacho, Amanda; Sampathkumaran, Jayanthi; Krueger, Clinton A.; Osgood, Mark A.; Wu, Ching

2013-01-01

Graphical abstract: -- Highlights: •A new ESI source was built for direct ionization from syringe. •Phthalates, food dyes, and sweeteners detected with high-performance IMS. •Phthalates directly detected in cola, soy bubble tea matrices with simple treatment. -- Abstract: High-performance ion mobility spectrometry (HPIMS) with an electrospray ionization (ESI) source detected a series of food contaminants and additive compounds identified as critical to monitoring the safety of food samples. These compounds included twelve phthalate plasticizers, legal and illegal food and cosmetic dyes, and artificial sweeteners that were all denoted as detection priorities. HPIMS separated and detected the range of compounds with a resolving power better than 60 in both positive and negative ion modes, comparable to the commonly used high-performance liquid chromatography (HPLC) methods, but with most acquisition times under a minute. The reduced mobilities, K 0 , have been determined, as have the linear response ranges for ESI-HPIMS, which are 1.5–2 orders of magnitude for concentrations down to sub-ng μL −1 levels. At least one unique mobility peak was seen for two subsets of the phthalates grouped by the country where they were banned. Furthermore, ESI-HPIMS successfully detected low nanogram levels of a phthalate at up to 30 times lower concentration than international detection levels in both a cola matrix and a soy-based bubble tea beverage using only a simplified sample treatment. A newly developed direct ESI source (Directspray) was combined with HPIMS to detect food-grade dyes and industrial dye adulterants, as well as the sweeteners sodium saccharin and sodium cyclamate, with the same good performance as with the phthalates. However, the Directspray method eliminated sources of carryover and decreased the time between sample runs. Limits-of-detection (LOD) for the analyte standards were estimated to be sub-ng μL −1 levels without extensive sample handling

High-performance ion mobility spectrometry with direct electrospray ionization (ESI-HPIMS) for the detection of additives and contaminants in food

Energy Technology Data Exchange (ETDEWEB)

Midey, Anthony J., E-mail: anthony.midey@excellims.com; Camacho, Amanda; Sampathkumaran, Jayanthi; Krueger, Clinton A.; Osgood, Mark A.; Wu, Ching

2013-12-04

Graphical abstract: -- Highlights: •A new ESI source was built for direct ionization from syringe. •Phthalates, food dyes, and sweeteners detected with high-performance IMS. •Phthalates directly detected in cola, soy bubble tea matrices with simple treatment. -- Abstract: High-performance ion mobility spectrometry (HPIMS) with an electrospray ionization (ESI) source detected a series of food contaminants and additive compounds identified as critical to monitoring the safety of food samples. These compounds included twelve phthalate plasticizers, legal and illegal food and cosmetic dyes, and artificial sweeteners that were all denoted as detection priorities. HPIMS separated and detected the range of compounds with a resolving power better than 60 in both positive and negative ion modes, comparable to the commonly used high-performance liquid chromatography (HPLC) methods, but with most acquisition times under a minute. The reduced mobilities, K{sub 0}, have been determined, as have the linear response ranges for ESI-HPIMS, which are 1.5–2 orders of magnitude for concentrations down to sub-ng μL{sup −1} levels. At least one unique mobility peak was seen for two subsets of the phthalates grouped by the country where they were banned. Furthermore, ESI-HPIMS successfully detected low nanogram levels of a phthalate at up to 30 times lower concentration than international detection levels in both a cola matrix and a soy-based bubble tea beverage using only a simplified sample treatment. A newly developed direct ESI source (Directspray) was combined with HPIMS to detect food-grade dyes and industrial dye adulterants, as well as the sweeteners sodium saccharin and sodium cyclamate, with the same good performance as with the phthalates. However, the Directspray method eliminated sources of carryover and decreased the time between sample runs. Limits-of-detection (LOD) for the analyte standards were estimated to be sub-ng μL{sup −1} levels without extensive

Synthesis, characterization and catalytic activity of acid-base bifunctional materials through protection of amino groups

Energy Technology Data Exchange (ETDEWEB)

Shao, Yanqiu [College of Chemistry, Jilin University, Changchun 130023 (China); College of Chemistry, Mudanjiang Normal University, Mudanjiang 157012 (China); Liu, Heng; Yu, Xiaofang [College of Chemistry, Jilin University, Changchun 130023 (China); Guan, Jingqi, E-mail: guanjq@jlu.edu.cn [College of Chemistry, Jilin University, Changchun 130023 (China); Kan, Qiubin, E-mail: qkan@mail.jlu.edu.cn [College of Chemistry, Jilin University, Changchun 130023 (China)

2012-03-15

Graphical abstract: Acid-base bifunctional mesoporous material SO{sub 3}H-SBA-15-NH{sub 2} was successfully synthesized under low acidic medium through protection of amino groups. Highlights: Black-Right-Pointing-Pointer The acid-base bifunctional material SO{sub 3}H-SBA-15-NH{sub 2} was successfully synthesized through protection of amino groups. Black-Right-Pointing-Pointer The obtained bifunctional material was tested for aldol condensation. Black-Right-Pointing-Pointer The SO{sub 3}H-SBA-15-NH{sub 2} catalyst containing amine and sulfonic acid groups exhibited excellent acid-basic properties. -- Abstract: Acid-base bifunctional mesoporous material SO{sub 3}H-SBA-15-NH{sub 2} was successfully synthesized under low acidic medium through protection of amino groups. X-ray diffraction (XRD), N{sub 2} adsorption-desorption, transmission electron micrographs (TEM), back titration, {sup 13}C magic-angle spinning (MAS) NMR and {sup 29}Si magic-angle spinning (MAS) NMR were employed to characterize the synthesized materials. The obtained bifunctional material was tested for aldol condensation reaction between acetone and 4-nitrobenzaldehyde. Compared with monofunctional catalysts of SO{sub 3}H-SBA-15 and SBA-15-NH{sub 2}, the bifunctional sample of SO{sub 3}H-SBA-15-NH{sub 2} containing amine and sulfonic acid groups exhibited excellent acid-basic properties, which make it possess high activity for the aldol condensation.

3D metal droplet printing development and advanced materials additive manufacturing

Directory of Open Access Journals (Sweden)

Lawrence E. Murr

2017-01-01

Full Text Available While commercial additive manufacturing processes involving direct metal wire or powder deposition along with powder bed fusion technologies using laser and electron beam melting have proliferated over the past decade, inkjet printing using molten metal droplets for direct, 3D printing has been elusive. In this paper we review the more than three decades of development of metal droplet generation for precision additive manufacturing applications utilizing advanced, high-temperature metals and alloys. Issues concerning process optimization, including product structure and properties affected by oxidation are discussed and some comparisons of related additive manufactured microstructures are presented.

Additive manufacturing with polypropylene microfibers.

Science.gov (United States)

Haigh, Jodie N; Dargaville, Tim R; Dalton, Paul D

2017-08-01

The additive manufacturing of small diameter polypropylene microfibers is described, achieved using a technique termed melt electrospinning writing. Sequential fiber layering, which is important for accurate three-dimensional fabrication, was achieved with the smallest fiber diameter of 16.4±0.2μm obtained. The collector speed, temperature and melt flow rate to the nozzle were optimized for quality and minimal fiber pulsing. Of particular importance to the success of this method is appropriate heating of the collector plate, so that the electrostatically drawn filament adheres during the direct-writing process. By demonstrating the direct-writing of polypropylene, new applications exploiting the favorable mechanical, stability and biocompatible properties of this polymer are envisaged. Copyright © 2017. Published by Elsevier B.V.

Template-directed addition of nucleosides to DNA by the BfiI restriction enzyme

OpenAIRE

Sasnauskas, Giedrius; Connolly, Bernard A.; Halford, Stephen E.; Siksnys, Virginijus

2008-01-01

Restriction endonucleases catalyse DNA cleavage at specific sites. The BfiI endonuclease cuts DNA to give staggered ends with 1-nt 3′-extensions. We show here that BfiI can also fill in the staggered ends: while cleaving DNA, it can add a 2′-deoxynucleoside to the reaction product to yield directly a blunt-ended DNA. We propose that nucleoside incorporation proceeds through a two-step reaction, in which BfiI first cleaves the DNA to make a covalent enzyme–DNA intermediate and then resolves it...

Directed network modules

International Nuclear Information System (INIS)

Palla, Gergely; Farkas, Illes J; Pollner, Peter; Derenyi, Imre; Vicsek, Tamas

2007-01-01

A search technique locating network modules, i.e. internally densely connected groups of nodes in directed networks is introduced by extending the clique percolation method originally proposed for undirected networks. After giving a suitable definition for directed modules we investigate their percolation transition in the Erdos-Renyi graph both analytically and numerically. We also analyse four real-world directed networks, including Google's own web-pages, an email network, a word association graph and the transcriptional regulatory network of the yeast Saccharomyces cerevisiae. The obtained directed modules are validated by additional information available for the nodes. We find that directed modules of real-world graphs inherently overlap and the investigated networks can be classified into two major groups in terms of the overlaps between the modules. Accordingly, in the word-association network and Google's web-pages, overlaps are likely to contain in-hubs, whereas the modules in the email and transcriptional regulatory network tend to overlap via out-hubs

Additional costs for Norwegian power companies from the OED-proposed implementation of the Electricity Directive II; Merkostnader for norske kraftselskaper ved OEDs forslag til implementering av Eldirektiv II

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

The cost-related consequences for Norwegian vertically integrated power companies caused by the proposed implementation of Electricity Directive II by OED (Norwegian Oil and Energy Department) are considered. Electricity Directive II demands a company and functional division between the network activities and the activities exposed to competition. The OED proposition aims at lowering the limit for which network companies are included by the new demands, from 100.000 to either 20.000 or 10.000 network clients. Moreover, they propose measures that ensure the network companies' independence, and these exceed by far the minimum requirements of Electricity Directive II. The additional costs may be significant in some aspects. Especially the requirement of an independent management in parent- and subsidiary company will lead to added costs of about Nok 320 million for the Norwegian power business. Further, a split-up management structure may be poorly compatible with the mind set behind the corporate model, something which potentially can lead to bad investments or a weaker utilization of potential cost synergies. The motive for proposing stricter demands on Norwegian power business is among other to limit cross-subsidies so that the competition in the market is reinforced. In light of substantial, quantified additional costs and other negative effects, the proposition's effect on the competition should be investigated further, including alternative measures that may be more cost-effective and/or more accurate (ml)

Enantioselective total synthesis of (+)-brefeldin A and 7-epi-brefeldin A.

Science.gov (United States)

Wu, Yikang; Shen, Xin; Yang, Yong-Qing; Hu, Qi; Huang, Jia-Hui

2004-05-28

A convergent enantioselective route to brefeldin A (BFA) and 7-epi-BFA was developed. The key C-4/C-5 chiral centers were established by using chiral auxiliary induced intermolecular asymmetric aldolization in the presence of TiCl(4) and TMEDA. The results with the thiazolidinethione/TiCl(4) mediated intermolecular asymmetric aldolization added some new information about the scope and limitations to the existing knowledge of that type of reactions (which so far was essentially limited to the reactions with N-propionyl thiazolidinethiones). During the course a method for protecting the liable aldol hydroxyl groups by using inexpensive TBSCl in DMF with 2,6-lutidine as the base was developed to replace the otherwise unavoidable TBSOTf procedure. Due to the excessive steric hindrance, removal of the auxiliary was much more difficult than most literature cases. Cleavage of the oxazolidinone by reduction was almost impossible. The thiazolidinethione auxiliary was relatively easier to remove. However, several reactions reported for facile removal of thiazolidinethione auxiliaries in the literature still failed. Reductive removal of the thiazolidinethione auxiliary was most effectively realized with LiBH(4) in diethyl ether in the presence of 1 equiv of MeOH (a modification of a literature procedure for removal of oxazolidinone auxiliaries in less hindered substrates). Apart from the auxiliary removal, oxidation of the alcohol into aldehyde and the deprotection of the dithiolane protecting group were also rather difficult in the present context. A range of methods were screened before final solutions were found. The five-membered ring was constructed by employing an intramolecular Mukaiyama reaction after many attempts with the intramolecular aldolization under a variety of conditions failed. The rate of elimination of the alkoxyl to form the alpha,beta-double bond of the key intermediate cyclopentenone 49 with DBU was highly solvent dependent (very sluggish in CH(2)Cl(2

Calcium(ii)-catalyzed enantioselective conjugate additions of amines.

Science.gov (United States)

Uno, Brice E; Dicken, Rachel D; Redfern, Louis R; Stern, Charlotte M; Krzywicki, Greg G; Scheidt, Karl A

2018-02-14

The direct enantioselective chiral calcium(ii)·phosphate complex (Ca[CPA] 2 )-catalyzed conjugate addition of unprotected alkyl amines to maleimides was developed. This mild catalytic system represents a significant advance towards the general convergent asymmetric amination of α,β-unsaturated electrophiles, providing medicinally relevant chiral aminosuccinimide products in high yields and enantioselectivities. Furthermore, the catalyst can be reused directly from a previously chromatographed reaction and still maintain both high yield and selectivity.

Development of coatings for ultrasonic additive manufacturing sonotrode using laser direct metal deposition process

Energy Technology Data Exchange (ETDEWEB)

Niyanth S, Niyanth [ORNL; Dehoff, Ryan R [ORNL; Jordan, Brian H [ORNL; Babu, Sudarsanam Suresh [ORNL

2016-10-01

ORNL partnered with Fabrisonic, LLC to develop galling resistant hard facing coatings on sonotrodes used to fabricate 3D printed materials using ultrasonic additive manufacturing. The development and deployment of a coated sonotrode is expected to push the existing state of the art to facilitate the solidstate additive manufacturing of hard steels and titanium alloys. To this effect a structurally amorphous stainless steel material and cobalt chrome material were deposited on the sonotrode material. Both the deposits showed good adhesion to the substrate. The coatings made using the structurally amorphous steel materials showed cracking during the initial trials and cracking was eliminated by deposition on a preheated substrate. Both the coatings show hardness in excess of 600 HVN. Thus the phase 1 of this project has been used to identify suitable materials to use to coat the sonotrode. Despite the fact that successful deposits were obtained, the coatings need to be evaluated by performing detailed galling tests at various temperatures. In addition field tests are also necessary to test the stability of these coatings in a high cycle ultrasonic vibration mode. If awarded, phase 2 of the project would be used to optimize the composition of the deposit material to maximize galling resistance. The industrial partner would then use the coated sonotrode to fabricate builds made of austenitic stainless steel to test the viability of using a coated sonotrode.

Freeze-dried formulation for direct {sup 99m}Tc-labeling ior-egf/r3 MAb: additives, biodistribution, and stability

Energy Technology Data Exchange (ETDEWEB)

Morales, Alejo A. Morales; Nunez-Gandolff, Gilda; Perez, Niuvis Perez; Veliz, Belkis Chico; Caballero-Torres, Idania; Duconge, Jorge; Fernandez, Eduardo; Crespo, Francisco Zayas; Veloso, Ana; Iznaga-Escobar, Normando E-mail: normando@ict.sld.cu

1999-08-01

Monoclonal antibodies (MAbs) have been useful for immunoscintigraphic applications in clinical diagnosis since they were introduced in nuclear medicine practice. The MAb ior egf/r3 developed at the Center of Molecular Immunology (Havana, Cuba) is a murine antibody that recognizes the human epidermal growth factor receptor (EGF-R) and has been used widely in the radioimmunodiagnosis of tumors of epithelial origin. Based on the direct Schwarz method, the present report describes the preparation of a freeze-dried formulation for radiolabeling the MAb ior egf/r3 with {sup 99m}Tc for immunoscintigraphic applications. Radiolabeling efficiency, effects on immunoreactivity, biodistribution, pharmacokinetic, and stability of the formulation are reported. The study demonstrated that the freeze-dried formulation can be labeled with {sup 99m}Tc at high yield. The resulting {sup 99m}Tc-labeled ior egf/r3 MAb can be used to visualize in vivo human tumors of epithelial origin by immunoscintigraphy studies. The kit does not need any other addition or purification at the time of tagging other than the requisite amount of pertechnetate (40-50 mCi). Because the contents of the kit are lyophilized, no special storage or transportation is required.

Advanced Material Studies for Additive Manufacturing in terms of Future Gear Application

Directory of Open Access Journals (Sweden)

Jan Bräunig

2014-06-01

Full Text Available Additive manufacturing by laser beam melting is predestined for complex component geometry like integrated cooling channels without enormous posttreatment processing. To investigate the influence of build-up direction in terms of later tooth excitation of gear-wheels, first fundamental material analyses were accomplished in this publication. Therefore, additively produced specimens were used to determine the build-up direction dependent elastic properties of the material in all three spatial directions based on tensile and torsion tests. The anisotropies of elastic limits and breaking points of previous studies were confirmed in this paper. Furthermore, torsion values were also determined depending on build-up direction. Laser beam melted X3NiCoMoTi18-9-5 (hot-work tool steel was shown to exhibit extremely high performance under shear loading in comparison to conventionally processed steel. The influence of build-up direction on torsional strength was also shown.

Organolanthanide reagents and the Mukaiyama reaction

International Nuclear Information System (INIS)

Gong, L.

1989-01-01

The bis(pentamethylcyclopentadienyl) lutetium halide complex [(C 5 Me 5 ) 2 LuCl/center dot/THF] was synthesized and characterized. The crystal structure of this complex shows that the Lu is at the center of a distorted tetrahedron consisting of the centroids of two cyclopentadienyl rings, the oxygen atom of a tetrahydrofuran molecule and a chlorine atom. 1 H NMR studies of toluene-d 8 solutions of (C 5 Me 5 LuCl(THF) + THF, (TMS 2 CP) 2 LuCl(THF) + THF, and (MeCp) 2 LuCl(THF) + THF at various temperatures showed exchange processes between co- ordinated THF and free THF with average values of ΔG/sup ne/ of 13.0 /+-/ 0.3 kcal/mol, 11.1 /+-/ 0.1 kcal/mol and 2 Cp) 2 YbCl dimer, silyl enol ethers (R 1 R 2 C = C(OR 3 )OSiMe 3 )) react with benzaldehyde smoothly in dichloromethane at room temperature, giving >99% of the aldol silyl ether (isolated yield: 90%) within 3 h. At /minus/78/degrees/C, the reaction gives kinetically controlled diastereoselectivity, which was not observed in the TiCl 4 -mediated aldol reaction. The use of organoytterbium enolates shows promise result with respect to increased stereoselectivity, and indicates the importance of the bulky ligands on the metal center. In addition, Yb(III) species can retard retroaldol reaction owing to its mild Lewis acidity. 118 refs., 14 figs., 30 tabs

A chiral analog of the bicyclic guanidine TBD: synthesis, structure and Brønsted base catalysis

Directory of Open Access Journals (Sweden)

Mariano Goldberg

2016-08-01

Full Text Available Starting from (S-β-phenylalanine, easily accessible by lipase-catalyzed kinetic resolution, a chiral triamine was assembled by a reductive amination and finally cyclized to form the title compound 10. In the crystals of the guanidinium benzoate salt the six membered rings of 10 adopt conformations close to an envelope with the phenyl substituents in pseudo-axial positions. The unprotonated guanidine 10 catalyzes Diels–Alder reactions of anthrones and maleimides (25–30% ee. It also promotes as a strong Brønsted base the retro-aldol reaction of some cycloadducts with kinetic resolution of the enantiomers. In three cases, the retro-aldol products (48–83% ee could be recrystallized to high enantiopurity (≥95% ee. The absolute configuration of several compounds is supported by anomalous X-ray diffraction and by chemical correlation.

PicPrint: Embedding pictures in additive manufacturing

DEFF Research Database (Denmark)

Nielsen, Jannik Boll; Eiríksson, Eyþór Rúnar; Lyngby, Rasmus Ahrenkiel

2017-01-01

Here  we  present  PicPrint,  a  method  and  tool  for  producing  an  additively  manufactured  lithophane,  enabling  transferring  and embedding  2D  information  into  additively  manufactured  3D  objects.  The  method  takes  an  input  image  and  converts  it  to  a......, after which  the mesh is  ready  for either  direct  print  on an additive manufacturing system, or transfer to other geometries via Boolean mesh operations. ...

Geometrical shape assessment of additively manufactured features by direct light processing vat polymerization method

DEFF Research Database (Denmark)

Péreza, Lucia C. Díaz; Davoudinejad, Ali; Quagliotti, Danilo

The importance of Additive Manufacturing (AM) in the field of micro manufacturing is increasing. Vat Polymerization Methods are one of the lead AM technologies to produce polymer micro parts. In the Technical University of Denmark (DTU), a vat photopolymerization AM machine able to print features...

Advances in 3D printing & additive manufacturing technologies

CERN Document Server

Pandey, Pulak; Kumar, L

2017-01-01

This edited volume comprises select chapters on advanced technologies for 3D printing and additive manufacturing and how these technologies have changed the face of direct, digital technologies for rapid production of models, prototypes and patterns. Because of its wide applications, 3D printing and additive manufacturing technology has become a powerful new industrial revolution in the field of manufacturing. The evolution of 3D printing and additive manufacturing technologies has changed design, engineering and manufacturing processes across industries such as consumer products, aerospace, medical devices and automotives. The objective of this book is to help designers, R&D personnel, and practicing engineers understand the state-of-the-art developments in the field of 3D Printing and Additive Manufacturing. .

Cyclopalladated complexes in enantioselective catalysis

Energy Technology Data Exchange (ETDEWEB)

Dunina, Valeria V; Gorunova, Olga N; Zykov, P A; Kochetkov, Konstantin A

2011-01-31

The results of the use of optically active palladacycles in enantioselective catalysis of [3,3]-sigmatropic rearrangements, aldol condensation, the Michael reaction and cross-coupling are analyzed. Reactions with allylic substrates or reagents and some other transformations are considered.

Additive effect of Ce, Mo and K to nickel-cobalt aluminate supported solid oxide fuel cell for direct internal reforming of methane

International Nuclear Information System (INIS)

Kwak, Bu Ho; Park, Jungdeok; Yoon, Heechul; Kim, Hyeon Hui; Kim, Lim; Chung, Jong Shik

2014-01-01

Direct internal reforming of methane (steam/carbon=0.031, 850 .deg. C) is tested using button cells of Ni-YSZ/YSZ/LSM in which the anode layer is supported either on Ni-YSZ or on Ni-CoAl 2 O 4 . The Ni-CoAl 2 O 4 supported cell shows little degradation with operating time, as a result of higher resistance against carbon deposition, whereas the Ni-YSZ supported cell deactivates quickly and suffers fracture in 50 h. Upon incorporation of additives such as K, Ce, or Mo into the Ni-CoAl 2 O 4 support, cells with 0.5 wt% CeO 2 exhibit the best stable performance as a result of reduced coke formation. Cells with 0.5 wt% Mo exhibit the lowest performance. Although no carbon deposit is detected in the cells with K 2 CO 3 additives, their performance is worse than that in the CeO 2 case, and, in constant-current mode, there is a sudden voltage drop to zero after a certain period of time; this time becomes shorter with increasing K content. The injection of potassium into the anode side facilitates the generation of OH - and CO 3 2- in the anode and promotes the diffusion of these ions to the cathode. Increased polarization resistance at the cathode and increased electrolyte resistance result in such a sudden failure

Estimating directional epistasis

Science.gov (United States)

Le Rouzic, Arnaud

2014-01-01

Epistasis, i.e., the fact that gene effects depend on the genetic background, is a direct consequence of the complexity of genetic architectures. Despite this, most of the models used in evolutionary and quantitative genetics pay scant attention to genetic interactions. For instance, the traditional decomposition of genetic effects models epistasis as noise around the evolutionarily-relevant additive effects. Such an approach is only valid if it is assumed that there is no general pattern among interactions—a highly speculative scenario. Systematic interactions generate directional epistasis, which has major evolutionary consequences. In spite of its importance, directional epistasis is rarely measured or reported by quantitative geneticists, not only because its relevance is generally ignored, but also due to the lack of simple, operational, and accessible methods for its estimation. This paper describes conceptual and statistical tools that can be used to estimate directional epistasis from various kinds of data, including QTL mapping results, phenotype measurements in mutants, and artificial selection responses. As an illustration, I measured directional epistasis from a real-life example. I then discuss the interpretation of the estimates, showing how they can be used to draw meaningful biological inferences. PMID:25071828

Additive manufacturing of tunable lenses

Science.gov (United States)

Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

2017-02-01

Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

F/Cl + C2H2 reactions: Are the addition and hydrogen abstraction direct processes?

International Nuclear Information System (INIS)

Li Jilai; Geng Caiyun; Huang Xuri; Zhan Jinhui; Sun Chiachung

2006-01-01

The reactions of atomic radical F and Cl with acetylene have been studied theoretically using ab initio quantum chemistry methods and transition state theory. The doublet potential energy surfaces were calculated at the CCSD(T)/aug-cc-pVDZ//CCSD/6-31G(d,p), CCSD(T)/aug-cc-pVDZ//UMP2/6-311++G(d,p) and compound method Gaussian-3 levels. Two reaction mechanisms including the addition-elimination and the hydrogen abstraction reaction mechanisms are considered. In the addition-elimination reactions, the halogen atoms approach C 2 H 2 , perpendicular to the C≡C triple bond, forming the pre-reactive complex C1 at the reaction entrance. C1 transforms to intermediate isomer I1 via transition state TSC1/1 with a negative/small barrier for C 2 H 2 F/C 2 H 2 Cl system, which can proceed by further eliminating H atom endothermally. While the hydrogen abstraction reactions also involve C1 for the fluorine atom abstraction of hydrogen, yet the hydrogen abstraction by chlorine atom first forms a collinear hydrogen-bonded complex C2. The other reaction pathways on the doublet PES are less competitive due to thermodynamical or kinetic factors. According to our results, the presence of pre-reactive complexes indicates that the simple hydrogen abstraction and addition in the halogen atoms reaction with unsaturated hydrocarbon should be more complex. Furthermore, based on the analysis of the kinetics of all channels through which the addition and abstraction reactions proceed, we expect that the actual feasibility of the reaction channels may depend on the reaction conditions in the experiment. The present study may be helpful for probing the mechanisms of the title reactions and understanding the halogen chemistry

SYNTHESIZING DERIVATIVES FROM CYCLOPENTANONE ANALOGUE CURCUMIN AND THEIR TOXIC, ANTIOXIDANT AND ANTI-INFLAMMATORY ACTIVITIES

Directory of Open Access Journals (Sweden)

Adel Zamri1

2011-11-01

Full Text Available Three types of cyclopentanone derivatives have been synthesized from aromatic aldehyde and ketone derivatives undera base condition through aldol condensation. These cyclopentanone products were 2,5-dibenzylidene-cyclopentanone(a, 2,5-bis-(4-hydroxy-benzylidene-cyclopentanone (b, and 2,5-bis-(4-hydroxy-benzylidene-cyclopentanone (cwhich has a yield of 63-99%. The chemical structure of these compounds were determined using UV, IR and NMRspectroscopy. In order to clarify the role of hydroxyl and amine moieties, toxic, antioxidant and anti-inflammatoryactivities were carried out. The toxic test indicated that the compounds showed strong toxicity. In addition, the presenceof hydroxyl and amine groups on both rings of curcumin increased the antioxidant and anti-inflammatory activities

Configuring NIF for direct drive experiments

International Nuclear Information System (INIS)

Eimerl, D.; Rothenberg, J.; Key, M.

1995-01-01

The National Ignition Facility (NIF) is a proposed 1.8 MJ laser facility for carrying out experiments in inertial confinement fusion, currently designed for indirect drive experiments. The direct drive approach is being pursued at the 30 kJ Omega facility at the University of Rochester. In this paper we discuss the modifications to the NIF laser that would be required for both indirect and direct drive experiments. A primary concern is the additional cost of adding direct drive capability to the facility

Additive derivations on algebras of measurable operators

International Nuclear Information System (INIS)

Ayupov, Sh.A.; Kudaybergenov, K.K.

2009-08-01

Given a von Neumann algebra M we introduce the so-called central extension mix(M) of M. We show that mix(M) is a *-subalgebra in the algebra LS(M) of all locally measurable operators with respect to M, and this algebra coincides with LS(M) if and only if M does not admit type II direct summands. We prove that if M is a properly infinite von Neumann algebra then every additive derivation on the algebra mix(M) is inner. This implies that on the algebra LS(M), where M is a type I ∞ or a type III von Neumann algebra, all additive derivations are inner derivations. (author)

3D FE simulation of semi-finishing machining of Ti6Al4V additively manufactured by direct metal laser sintering

Science.gov (United States)

Imbrogno, Stano; Rinaldi, Sergio; Raso, Antonio; Bordin, Alberto; Bruschi, Stefania; Umbrello, Domenico

2018-05-01

The Additive Manufacturing techniques are gaining more and more interest in various industrial fields due to the possibility of drastically reduce the material waste during the production processes, revolutionizing the standard scheme and strategies of the manufacturing processes. However, the metal parts shape produced, frequently do not satisfy the tolerances as well as the surface quality requirements. During the design phase, the finite element simulation results a fundamental tool to help the engineers in the correct decision of the most suitable process parameters, especially in manufacturing processes, in order to produce products of high quality. The aim of this work is to develop a 3D finite element model of semi-finishing turning operation of Ti6Al4V, produced via Direct Metal Laser Sintering (DMLS). A customized user sub-routine was built-up in order to model the mechanical behavior of the material under machining operations to predict the main fundamental variables as cutting forces and temperature. Moreover, the machining induced alterations are also studied by the finite element model developed.

Reconsidering Money: Monetary Exchange with Additive Transaction Costs

DEFF Research Database (Denmark)

Schröder, Philipp

2001-01-01

Under the assumption of purely additive transaction costs in exchange, the literature on money has a standard example of direct exchange dominating indirect (monetary) exchange. From here it is frequently concluded that subadditive costs (e.g. search costs) must be examined in order to explain...... money. In contrast, this paper presents an additive transaction costs model in which the mere absence of double coincidences of wants suffices to motivate monetary exchange. Furthermore it is found that not all commodity moneys, that are collectively desirable, qualify for the core, but that all fiat...

Additive effect of Ce, Mo and K to nickel-cobalt aluminate supported solid oxide fuel cell for direct internal reforming of methane

Energy Technology Data Exchange (ETDEWEB)

Kwak, Bu Ho; Park, Jungdeok; Yoon, Heechul; Kim, Hyeon Hui; Kim, Lim; Chung, Jong Shik [POSTECH, Pohang (Korea, Republic of)

2014-01-15

Direct internal reforming of methane (steam/carbon=0.031, 850 .deg. C) is tested using button cells of Ni-YSZ/YSZ/LSM in which the anode layer is supported either on Ni-YSZ or on Ni-CoAl{sub 2}O{sub 4}. The Ni-CoAl{sub 2}O{sub 4} supported cell shows little degradation with operating time, as a result of higher resistance against carbon deposition, whereas the Ni-YSZ supported cell deactivates quickly and suffers fracture in 50 h. Upon incorporation of additives such as K, Ce, or Mo into the Ni-CoAl{sub 2}O{sub 4} support, cells with 0.5 wt% CeO{sub 2} exhibit the best stable performance as a result of reduced coke formation. Cells with 0.5 wt% Mo exhibit the lowest performance. Although no carbon deposit is detected in the cells with K{sub 2}CO{sub 3} additives, their performance is worse than that in the CeO{sub 2} case, and, in constant-current mode, there is a sudden voltage drop to zero after a certain period of time; this time becomes shorter with increasing K content. The injection of potassium into the anode side facilitates the generation of OH{sup -} and CO{sub 3}{sup 2-} in the anode and promotes the diffusion of these ions to the cathode. Increased polarization resistance at the cathode and increased electrolyte resistance result in such a sudden failure.

Ultrasound-assisted synthesis of curcumin analogs promoted by activated chicken eggshells

Science.gov (United States)

Mardiana, L.; Ardiansah, B.; Septiarti, A.; Bakri, R.; Kosamagi, G.

2017-07-01

Curcumin has been widely known as a multifunctional natural product which has many biological activities. However, the biggest limitation for the large scale application of curcumin is its poor bioavailability. This research presented a cheap, mild and efficient solvent-free synthesis of monocarbonyl analogs of curcumin via Aldol condensation using activated chicken eggshells (ACE). Dibenzalpropanone as a product of Aldol condensation was prepared by mixing benzaldehyde and acetone using a simple glass tube in the presence of ACE under ultrasound irradiation (78 % yield), while dibenzalcyclohexanone was produced from the reaction of benzaldehyde with cyclohenxanone (81 %). The products have been characterized by FTIR, UV-Vis spectrophotometer and GC-MS instruments. The FTIR spectra show a significant absorption of carbonyl group that attached to the double bond in α,β-position at 1630-1660 cm-1. The molecular cation of m/z of 234 and 274 is in agreement with the products structures.

Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS.

Science.gov (United States)

Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

2014-07-01

Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives.

Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS

Science.gov (United States)

Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

2014-01-01

Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives. PMID:25473499

Some additional results on the directional relationships between forces and accelerations in special relativity

International Nuclear Information System (INIS)

Gonzalez-Diaz, P.F.

1979-01-01

Some directional relationships between forces and accelerations in special relativity have been studied by considering the most general case of a body having x, y and z components of velocity, which is acted upon by a force with nonzero components. The behaviour of asub(y)/asub(x) and asub(y)/asub(z) vs. velocity for different force component ratios is studied in the general situation in which vsub(x) is unequal to vsub(y) is unequal to vsub(z). It is shown that one or two, suddenly varying, negative acceleration components can result for the body at sufficiently high velocities, and an explanation is given. (author)

Some additional results on the directional relationships between forces and accelerations in special relativity

International Nuclear Information System (INIS)

Gonzales-Diaz, P.F.

1979-01-01

Some directional relationships between forces and accelerations in special relativity have been studied by considering the most general case of a body having x, y and z components of velocity, which is acted upon by a force with nonzero components. The behaviour of a sub(y)/ a sub(x) and a sub(y)/ a sub(z) vs. velocity for different force component ratios is studied in the general situation in which vsub(x) different from Vsub(y)different from vsub(z). It is shown that one or two, suddently varying, negative acceleration components can result for the body at sufficiently high velocities, and an explanation is given

Synthesis of acid-base bifunctional mesoporous materials by oxidation and thermolysis

Energy Technology Data Exchange (ETDEWEB)

Yu, Xiaofang [College of Chemistry, Jilin University, Jiefang Road 2519, Changchun 130023 (China); Zou, Yongcun [State Key Laboratory of Inoranic Synthesis and Preparative Chemistryg, College of Chemistry, Jilin University, Changchun 130012 (China); Wu, Shujie; Liu, Heng [College of Chemistry, Jilin University, Jiefang Road 2519, Changchun 130023 (China); Guan, Jingqi, E-mail: guanjq@jlu.edu.cn [College of Chemistry, Jilin University, Jiefang Road 2519, Changchun 130023 (China); Kan, Qiubin, E-mail: qkan@jlu.edu.cn [College of Chemistry, Jilin University, Jiefang Road 2519, Changchun 130023 (China)

2011-06-15

Graphical abstract: A novel and efficient method has been developed for the synthesis of acid-base bifunctional catalyst. The obtained sample of SO{sub 3}H-MCM-41-NH{sub 2} containing amine and sulfonic acids exhibits excellent catalytic activity in aldol condensation reaction. Research highlights: {yields} Synthesize acid-base bifunctional mesoporous materials SO{sub 3}H-MCM-41-NH{sub 2}. {yields} Oxidation and then thermolysis to generate acidic site and basic site. {yields} Exhibit good catalytic performance in aldol condensation reaction between acetone and various aldehydes. -- Abstract: A novel and efficient method has been developed for the synthesis of acid-base bifunctional catalyst SO{sub 3}H-MCM-41-NH{sub 2}. This method was achieved by co-condensation of tetraethylorthosilicate (TEOS), 3-mercaptopropyltrimethoxysilane (MPTMS) and (3-triethoxysilylpropyl) carbamicacid-1-methylcyclohexylester (3TAME) in the presence of cetyltrimethylammonium bromide (CTAB), followed by oxidation and then thermolysis to generate acidic site and basic site. X-ray diffraction (XRD) and transmission electron micrographs (TEM) show that the resultant materials keep mesoporous structure. Thermogravimetric analysis (TGA), X-ray photoelectron spectra (XPS), back titration, solid-state {sup 13}C CP/MAS NMR and solid-state {sup 29}Si MAS NMR confirm that the organosiloxanes were condensed as a part of the silica framework. The bifunctional sample (SO{sub 3}H-MCM-41-NH{sub 2}) containing amine and sulfonic acids exhibits excellent acid-basic properties, which make it possess high activity in aldol condensation reaction between acetone and various aldehydes.

Computer Modeling of Direct Metal Laser Sintering

Science.gov (United States)

Cross, Matthew

2014-01-01

A computational approach to modeling direct metal laser sintering (DMLS) additive manufacturing process is presented. The primary application of the model is for determining the temperature history of parts fabricated using DMLS to evaluate residual stresses found in finished pieces and to assess manufacturing process strategies to reduce part slumping. The model utilizes MSC SINDA as a heat transfer solver with imbedded FORTRAN computer code to direct laser motion, apply laser heating as a boundary condition, and simulate the addition of metal powder layers during part fabrication. Model results are compared to available data collected during in situ DMLS part manufacture.

Chiral 1,3,2-oxazaborolidines in asymmetric synthesis: recent advances

International Nuclear Information System (INIS)

Glushkov, Vladimir A; Tolstikov, Alexander G

2004-01-01

The use of chiral 1,3,2-oxazaborolidines in asymmetric organic synthesis, particularly, in enantioselective reduction of ketones, imines and oxime ethers, asymmetric Diels-Alder reactions, aldol condensation and atroposelective reduction of lactones is reviewed. Reactions of immobilised 1,3,2-oxazaborolidines are also considered.

Annual Letter Report on ONR (Office of Naval Research) Contract Number N00014-85-K-0228.

Science.gov (United States)

1985-12-02

olefination, ".. and thioketalization, are currently under way. Stabilization of these polyketones _ with respect to aldolization is particularly important for...11 NaH High Dilution 67 ..- expected that a knotted polyketone will be especially prone to intramolecular trans-annular reactions. The four-rung THYME

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Rhodanine derivatives are highly valuable heterocycles in drug discovery. Here, we developed aldol reaction of N-substituted rhodanines and aromatic aldehydes on water. The reaction was performed at room temperature affording the products in good to high yield. This synthetic protocol uses simple experimental ...

Calcium Oxide Supported on Monoclinic Zirconia as a Highly Active Solid Base Catalyst

NARCIS (Netherlands)

Frey, A.M.; Haasterecht, van T.; Jong, de K.P.; Bitter, J.H.

2013-01-01

Calcium oxide supported on ZrO2 is a highly active catalyst for base-catalyzed reactions such as aldol-type reactions and transesterification reactions. The role of key parameters during preparation, that is, impregnation versus precipitation, heat treatment, and metal oxide loading on the basicity

Direct marketing and market communication process

Directory of Open Access Journals (Sweden)

Jovović Sanja

2007-01-01

Full Text Available Direct marketing is marketing which demands immediate reply. That reply can be an order, a request for an additional information, a registration, a telephone call or a visit. This work presents direct marketing as the most contemporary method of company communications with environs. A concept of direct marketing is made and aimed for complete identification of existing customers and for finding out potential customers. Mail, printed documents e-mail and new medias are used as modern communications channels. It is especially emphasizes the Internet as an important media.

Laser Additive Manufacturing of Magnetic Materials

Science.gov (United States)

Mikler, C. V.; Chaudhary, V.; Borkar, T.; Soni, V.; Jaeger, D.; Chen, X.; Contieri, R.; Ramanujan, R. V.; Banerjee, R.

2017-03-01

While laser additive manufacturing is becoming increasingly important in the context of next-generation manufacturing technologies, most current research efforts focus on optimizing process parameters for the processing of mature alloys for structural applications (primarily stainless steels, titanium base, and nickel base alloys) from pre-alloyed powder feedstocks to achieve properties superior to conventionally processed counterparts. However, laser additive manufacturing or processing can also be applied to functional materials. This article focuses on the use of directed energy deposition-based additive manufacturing technologies, such as the laser engineered net shaping (LENS™) process, to deposit magnetic alloys. Three case studies are presented: Fe-30 at.%Ni, permalloys of the type Ni-Fe-V and Ni-Fe-Mo, and Fe-Si-B-Cu-Nb (derived from Finemet) alloys. All these alloys have been processed from a blend of elemental powders used as the feedstock, and their resultant microstructures, phase formation, and magnetic properties are discussed in this paper. Although these alloys were produced from a blend of elemental powders, they exhibited relatively uniform microstructures and comparable magnetic properties to those of their conventionally processed counterparts.

Culture and neuroscience: additive or synergistic?

Science.gov (United States)

Dapretto, Mirella; Iacoboni, Marco

2010-01-01

The investigation of cultural phenomena using neuroscientific methods—cultural neuroscience (CN)—is receiving increasing attention. Yet it is unclear whether the integration of cultural study and neuroscience is merely additive, providing additional evidence of neural plasticity in the human brain, or truly synergistic, yielding discoveries that neither discipline could have achieved alone. We discuss how the parent fields to CN: cross-cultural psychology, psychological anthropology and cognitive neuroscience inform the investigation of the role of cultural experience in shaping the brain. Drawing on well-established methodologies from cross-cultural psychology and cognitive neuroscience, we outline a set of guidelines for CN, evaluate 17 CN studies in terms of these guidelines, and provide a summary table of our results. We conclude that the combination of culture and neuroscience is both additive and synergistic; while some CN methodologies and findings will represent the direct union of information from parent fields, CN studies employing the methodological rigor required by this logistically challenging new field have the potential to transform existing methodologies and produce unique findings. PMID:20083533

The direct asymmetric vinylogous aldol reaction of furanones with α-ketoesters: Access to chiral γ-Butenolides and glycerol derivatives

KAUST Repository

Luo, Jie; Wang, Haifei; Han, Xiao; Xu, Liwen; Kwiatkowski, Jacek; Huang, Kuo-Wei; Lu, Yixin

2011-01-01

Twice as good: The title reaction using the tryptophan-derived bifunctional organic catalyst 1 has been developed. The reported method led to the synthesis of chiral γ-substituted butenolides in excellent yields, with high diastereo- and enantioselectivities. Facile synthesis of chiral glycerol derivatives containing a tertiary hydroxy group has also been demonstrated. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The direct asymmetric vinylogous aldol reaction of furanones with α-ketoesters: Access to chiral γ-Butenolides and glycerol derivatives

KAUST Repository

Luo, Jie

2011-01-11

Twice as good: The title reaction using the tryptophan-derived bifunctional organic catalyst 1 has been developed. The reported method led to the synthesis of chiral γ-substituted butenolides in excellent yields, with high diastereo- and enantioselectivities. Facile synthesis of chiral glycerol derivatives containing a tertiary hydroxy group has also been demonstrated. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Highly enantio- and diastereoselective reactions of γ-substituted butenolides through direct vinylogous conjugate additions

KAUST Repository

Zhang, Wen; Tan, Davin; Lee, Richmond; Tong, Guanghu; Chen, Wenchao; Qi, Baojian; Huang, Kuo-Wei; Tan, Choonhong; Jiang, Zhiyong

2012-01-01

The strength of the weak: An L-tert-leucine-derived amine-thiourea catalyst (see scheme, green box) promotes the asymmetric vinylogous conjugate addition reaction between γ-aryl- and alkyl-substituted butenolides with the butenamides and enoates shown. Computational studies show the preference for the observed stereochemistry is a result of favourable weak non-bonding interactions, which stabilize the transition state. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Highly enantio- and diastereoselective reactions of γ-substituted butenolides through direct vinylogous conjugate additions

KAUST Repository

Zhang, Wen

2012-09-05

The strength of the weak: An L-tert-leucine-derived amine-thiourea catalyst (see scheme, green box) promotes the asymmetric vinylogous conjugate addition reaction between γ-aryl- and alkyl-substituted butenolides with the butenamides and enoates shown. Computational studies show the preference for the observed stereochemistry is a result of favourable weak non-bonding interactions, which stabilize the transition state. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Toward Additive-Free Small-Molecule Organic Solar Cells: Roles of the Donor Crystallization Pathway and Dynamics

KAUST Repository

Abdelsamie, Maged

2015-09-29

The ease with which small-molecule donors crystallize during solution processing is directly linked to the need for solvent additives. Donor molecules that get trapped in disordered (H1) or liquid crystalline (T1) mesophases require additive processing to promote crystallization, phase separation, and efficient light harvesting. A donor material (X2) that crystallizes directly from solution yields additive-free solar cells with an efficiency of 7.6%. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Some recent results in finitely additive white noise theory

NARCIS (Netherlands)

Bagchi, Arunabha; Mazumdar, Ravi

1994-01-01

We present a short survey of some very recent results on the finitely additive white noise theory. We discuss the Markov property of the solution of a stochastic differential equation driven directly by a white noise, study the Radon-Nikodym derivative of the measure induced by nonlinear

Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints

DEFF Research Database (Denmark)

Thompson, Mary Kathryn; Moroni, Giovanni; Vaneker, Tom

2016-01-01

The past few decades have seen substantial growth in Additive Manufacturing (AM) technologies. However, this growth has mainly been process-driven. The evolution of engineering design to take advantage of the possibilities afforded by AM and to manage the constraints associated with the technology...... has lagged behind. This paper presents the major opportunities, constraints, and economic considerations for Design for Additive Manufacturing. It explores issues related to design and redesign for direct and indirect AM production. It also highlights key industrial applications, outlines future...

Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints

DEFF Research Database (Denmark)

Thompson, Mary Kathryn; Moroni, Giovanni; Vaneker, Tom

2016-01-01

has lagged behind. This paper presents the major opportunities, constraints, and economic considerations for Design for Additive Manufacturing. It explores issues related to design and redesign for direct and indirect AM production. It also highlights key industrial applications, outlines future......The past few decades have seen substantial growth in Additive Manufacturing (AM) technologies. However, this growth has mainly been process-driven. The evolution of engineering design to take advantage of the possibilities afforded by AM and to manage the constraints associated with the technology...

Direct Numerical Simulations of Microstructure Effects During High-Rate Loading of Additively Manufactured Metals

Science.gov (United States)

Battaile, Corbett; Owen, Steven; Moore, Nathan

2017-06-01

The properties of most engineering materials depend on the characteristics of internal microstructures and defects. In additively manufactured (AM) metals, these can include polycrystalline grains, impurities, phases, and significant porosity that qualitatively differ from conventional engineering materials. The microscopic details of the interactions between these internal defects, and the propagation of applied loads through the body, act in concert to dictate macro-observable properties like strength and compressibility. In this work, we used Sandia's ALEGRA finite element software to simulate the high-strain-rate loading of AM metals from laser engineered net shaping (LENS) and thermal spraying. The microstructural details of the material were represented explicitly, such that internal features like second phases and pores are captured and meshed as individual entities in the computational domain. We will discuss the dependence of the high-strain-rate mechanical properties on microstructural characteristics such as the shapes, sizes, and volume fractions of second phases and pores. In addition, we will examine how the details of the microstructural representation affect the microscopic material response to dynamic loads, and the effects of using ``stair-step'' versus conformal interfaces smoothed via the SCULPT tool in Sandia's CUBIT software. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the US DOE NNSA under contract DE-AC04-94AL85000.

21 CFR 70.25 - Labeling requirements for color additives (other than hair dyes).

Science.gov (United States)

2010-04-01

... for the use of the color additive, such as “for food use only”; “for food, drug, and cosmetic use... limitations for a general or specific use of a straight color, the amount of each such straight color in terms... or specific use of a color additive, the label shall in addition provide directions for use of the...

Laser direct writing using submicron-diameter fibers.

Science.gov (United States)

Tian, Feng; Yang, Guoguang; Bai, Jian; Xu, Jianfeng; Hou, Changlun; Liang, Yiyong; Wang, Kaiwei

2009-10-26

In this paper, a novel direct writing technique using submicron-diameter fibers is presented. The submicron-diameter fiber probe serves as a tightly confined point source and it adopts micro touch mode in the process of writing. The energy distribution of direct writing model is analyzed by Three-Dimension Finite-Difference Time-Domain method. Experiments demonstrate that submicron-diameter fiber direct writing has some advantages: simple process, 350-nm-resolution (lower than 442-nm-wavelength), large writing area, and controllable width of lines. In addition, by altering writing direction of lines, complex submicron patterns can be fabricated.

Synthesis of the C1-C28 Portion of Spongistatin 1 (Altohyrtin A).

Science.gov (United States)

Claffey, Michelle M.; Hayes, Christopher J.; Heathcock, Clayton H.

1999-10-29

A synthetic approach was developed to the C1-C28 subunit of spongistatin 1 (altohyrtin A, 65). The key step was the coupling of the AB and CD spiroketal moieties via an anti-aldol reaction of aldehyde 62 and ethyl ketone 57. The development of a method for the construction of the AB spiroketal fragment is described and included the desymmetrization of C(2)-symmetric diketone 10 and the differentiation of the two primary alcohols of 16. Further elaboration of this advanced intermediate to the desired aldehyde 62 included an Evans' syn-aldol reaction and Tebbe olefination. The synthesis of the CD spiroketal fragment 56 involved the ketalization of a triol-dione, generated in situ by deprotection of 45, to provide a favorable ratio (6-7:1) of spiroketal isomers 46 and 47, respectively. The overall protecting group strategy, involving many selective manipulations of silyl protecting groups, was successfully developed to provide the desired C1-C28 subunit of spongistatin 1 (altohyrtin A) (65).

Direct use in Hawaii

International Nuclear Information System (INIS)

Beck, A.G.

1990-01-01

This paper reports on a public laboratory, Noi'i O Puna, that was established in Hawaii to support direct use research in 1985, tapping the previously unutilized heat in brines from the HGP-A well. Two rounds of small grants were offered to entrepreneurs. With the closure of the HGP-A power plant in late 1989, Noi'i O Puna is expanding its facilities. When the HGP-A well is back in service, Noi'i O Puna will be able to support additional research and development projects, as well as pre-commercial ventures. Direct use industries, which support existing agricultural activities in the region have good potential

Evaluation of Advanced Polymers for Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Rios, Orlando [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Carter, William G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kutchko, Cindy [PPG Industries, Pittsburgh, PA (United States); Fenn, David [PPG Industries, Pittsburgh, PA (United States); Olson, Kurt [PPG Industries, Pittsburgh, PA (United States)

2017-09-08

The goal of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Oak Ridge National Laboratory (ORNL) and PPG Industries, Inc. (PPG) was to evaluate the feasibility of using conventional coatings chemistry and technology to build up material layer-by-layer. The PPG-ORNL study successfully demonstrated that polymeric coatings formulations may overcome many limitations of common thermoplastics used in additive manufacturing (AM), allow lightweight nozzle design for material deposition, and increase build rate. The materials effort focused on layer-by-layer deposition of coatings with each layer fusing together. The combination of materials and deposition results in an additively manufactured build that has sufficient mechanical properties to bear the load of additional layers, yet is capable of bonding across the z-layers to improve build direction strength. The formulation properties were tuned to enable a novel, high-throughput deposition method that is highly scalable, compatible with high loading of reinforcing fillers, and inherently low-cost.

[Trends in the utilization of food additives].

Science.gov (United States)

Szűcs, Viktória; Bánáti, Diána

2013-11-17

The frequent media reports on food additives weakened consumers' trust in food producers and food control authorities as well. Furthermore, consumers' uncertainty is also raised by the fact that they obtain their information from inadequate, mistrustful sources and, therefore, consumers might avoid the consumption of certain foodstuffs. While food producers may react by replacing artificial components by natural ones, they try to emphasize the favourable characteristics of their products. The authors describe the main trends and efforts related to food additives. On the basis of the overview it can be concluded that - besides taking into consideration consumers' needs - product development and research directions are promising. Food producers' efforts may help to restore consumer confidence and trust and they may help them to have informed choice.

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Additional requirements for special dipping and coating... Dipping and Coating Operations § 1910.126 Additional requirements for special dipping and coating... requirements apply to flow coating? (1) You must use a direct low-pressure pumping system or a 10-gallon (38 L...

Additive Manufactured Very Light Weight Diamond Turned Aspheric Mirror, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Selective laser melting, referred to as "Direct Metal Laser Sintering"(DMLS), "Metal Powder Bed Fusion" or "3D Printing" is an additive manufacturing process which...

1,1-Dimetallic reagents for the elaboration of stereoselectively di- or trisubstituted linear substrates.

Science.gov (United States)

Normant, J F

2001-08-01

Although gem-dimetallic species have been known for a long time, and reacted once or twice with electrophiles, the allyl zincation of substituted vinyl metals has emerged as a particularly efficient access to such species. This is due to a high face selectivity, in the addition to the C=C bond, which can be governed by vicinal or more remote heteroatoms. This strategy has some aspects in common with the well-known allylations or aldol condensations to carbonyl derivatives. But in the present case, the C=C bond has a low polarity. We present here some examples which lead to di- or polysubstituted linear substrates, of given geometry, where the organodimetallic obtained has been doubly protonated by water. Further elaborations (to alkenes, ketones, etc.) are possible.

Total synthesis and structural validation of cyclodepsipeptides solonamide A and B

DEFF Research Database (Denmark)

Kitir, Betül; Baldry, Mara; Ingmer, Hanne

2014-01-01

, autoinducing peptide I (AIP-I). To enable more comprehensive studies, we embarked on the chemical synthesis of solonamides A and B. The key synthetic steps were formation of the (R)-β-hydroxy-fatty-acids by stereo-selective aldol reactions and a cyclative macrolactamization, which proceeded under highly dilute...

A Multistep Synthesis Featuring Classic Carbonyl Chemistry for the Advanced Organic Chemistry Laboratory

Science.gov (United States)

Duff, David B.; Abbe, Tyler G.; Goess, Brian C.

2012-01-01

A multistep synthesis of 5-isopropyl-1,3-cyclohexanedione is carried out from three commodity chemicals. The sequence involves an aldol condensation, Dieckmann-type annulation, ester hydrolysis, and decarboxylation. No purification is required until after the final step, at which point gravity column chromatography provides the desired product in…

Synthesis and in vitro anticancer activity of 23(23′)E-benzylidenespirostanols derived from steroid sapogenins

Czech Academy of Sciences Publication Activity Database

Ramos-Enríquez, M. A.; Vargas-Romero, K.; Rárová, L.; Strnad, Miroslav; Iglesias-Arteaga, M. A.

2017-01-01

Roč. 128, DEC (2017), s. 85-88 ISSN 0039-128X R&D Projects: GA ČR GA17-14007S Institutional support: RVO:61389030 Keywords : Aldol condensation * Benzylidenespirostanols * Cancer cell lines * Cytotoxicity * Fibroblasts Subject RIV: FD - Oncology ; Hematology OBOR OECD: Oncology Impact factor: 2.282, year: 2016

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Direct electromechanical driving systems: diversity, constraints and solutions; Les entrainements electromecaniques directs: diversite, contraintes et solutions

Energy Technology Data Exchange (ETDEWEB)

Multon, B. [Ecole Normale Superieure, 94 - Cachan (France); Bonal, J. [Promethee Groupe Schneider Electric S.A., 92 - Boulogne-Billancourt (France)

1999-11-01

Direct electromechanical drives are the simplest possible transmission systems requiring no additional mechanical components such as gearboxes or rotary to linear converters. This simplicity leads a number of advantages including greater reliability, less maintenance, improved dynamic characteristics and reduced weight and volume. However, the performance specification of direct drives is usually high, with a correspondingly high cost, and often this cannot be justified in complete systems where the other components limit the overall performance. This factor alone has been sufficient to restrict the market penetration of direct drives. The majority of applications are in linear actuators, and in motors operating at very high or very low speeds. New developments are constantly being introduced, especially in relation to structures.

Cost estimation of a specifically designed direct light processing (DLP) additive manufacturing machine for precision printing

DEFF Research Database (Denmark)

Charalambis, Alessandro; Davoudinejad, Ali; Tosello, Guido

2017-01-01

creating new opportunities for manufacturers in a variety of industrial sectors. AM is an essentialprototyping technique for product design and development that is used in many different fields. However, the suitability of AMapplications in actual production in an industrial context needs to be determined......Additive Manufacturing (AM) refers to a portfolio of novel manufacturing technologies based on a layer-by-layer fabrication method.The market and industrial application of additive manufacturing technologies as an established manufacturing process have increasedexponentially in the last years....... This study, presents a cost estimation model forprecision printing with a specifically designed Digital Light Processing (DLP) AM machine built and validated at the Technical Universityof Denmark. The model presented in this study can be easily adapted and applied to estimate within a high level...

Fatigue crack propagation in additively manufactured porous biomaterials.

Science.gov (United States)

Hedayati, R; Amin Yavari, S; Zadpoor, A A

2017-07-01

Additively manufactured porous titanium implants, in addition to preserving the excellent biocompatible properties of titanium, have very small stiffness values comparable to those of natural bones. Although usually loaded in compression, biomedical implants can also be under tensional, shear, and bending loads which leads to crack initiation and propagation in their critical points. In this study, the static and fatigue crack propagation in additively manufactured porous biomaterials with porosities between 66% and 84% is investigated using compact-tension (CT) samples. The samples were made using selective laser melting from Ti-6Al-4V and were loaded in tension (in static study) and tension-tension (in fatigue study) loadings. The results showed that displacement accumulation diagram obtained for different CT samples under cyclic loading had several similarities with the corresponding diagrams obtained for cylindrical samples under compression-compression cyclic loadings (in particular, it showed a two-stage behavior). For a load level equaling 50% of the yield load, both the CT specimens studied here and the cylindrical samples we had tested under compression-compression cyclic loading elsewhere exhibited similar fatigue lives of around 10 4 cycles. The test results also showed that for the same load level of 0.5F y , the lower density porous structures demonstrate relatively longer lives than the higher-density ones. This is because the high bending stresses in high-density porous structures gives rise to local Mode-I crack opening in the rough external surface of the struts which leads to quicker formation and propagation of the cracks. Under both the static and cyclic loading, all the samples showed crack pathways which were not parallel to but made 45 ° angles with respect to the notch direction. This is due to the fact that in the rhombic dodecahedron unit cell, the weakest struts are located in 45 ° direction with respect to the notch direction

new spiro (thio) barbiturates based on cyclohexanone and bicyclo

African Journals Online (AJOL)

Preferred Customer

condensation can be operated with the aid of strong acids or bases [2, 13]. Several catalytic methods have been achieved for crossed-aldol condensation [4, 14-31]. Several spiro-(thio)barbituric acid derivatives in which the active methylene carbon of. (thio)barbituric acid is substituted by an unsubstituted cyclobutane or ...

7 CFR 1951.240 - State Director's additional authorizations and guidance.

Science.gov (United States)

2010-01-01

... the recipient's legal organizational structure must be approved by OGC. (2) Consent to requests by the...) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE... Servicing of Community and Direct Business Programs Loans and Grants § 1951.240 State Director's additional...

Non-Archimedean Hyers-Ulam Stability of an Additive-Quadratic Mapping

Directory of Open Access Journals (Sweden)

Hassan Azadi Kenary

2012-01-01

Full Text Available Using fixed point method and direct method, we prove the Hyers-Ulam stability of the following additive-quadratic functional equation 2((++/+2((−+/+2((+−/+2((−++/=4(+4(+4(, where is a positive real number, in non-Archimedean normed spaces.

Additive Manufacturing of Metastable Beta Titanium Alloys

Science.gov (United States)

Yannetta, Christopher J.

Additive manufacturing processes of many alloys are known to develop texture during the deposition process due to the rapid reheating and the directionality of the dissipation of heat. Titanium alloys and with respect to this study beta titanium alloys are especially susceptible to these effects. This work examines Ti-20wt%V and Ti-12wt%Mo deposited under normal additive manufacturing process parameters to examine the texture of these beta-stabilized alloys. Both microstructures contained columnar prior beta grains 1-2 mm in length beginning at the substrate with no visible equiaxed grains. This microstructure remained constant in the vanadium system throughout the build. The microstructure of the alloy containing molybdenum changed from a columnar to an equiaxed structure as the build height increased. Eighteen additional samples of the Ti-Mo system were created under different processing parameters to identify what role laser power and travel speed have on the microstructure. There appears to be a correlation in alpha lath size and power density. The two binary alloys were again deposited under the same conditions with the addition of 0.5wt% boron to investigate the effects an insoluble interstitial alloying element would have on the microstructure. The size of the prior beta grains in these two alloys were reduced with the addition of boron by approximately 50 (V) and 100 (Mo) times.

Silage review: Recent advances and future uses of silage additives.

Science.gov (United States)

Muck, R E; Nadeau, E M G; McAllister, T A; Contreras-Govea, F E; Santos, M C; Kung, L

2018-05-01

to apply a direct-fed microbial strain at ensiling, have it survive ensiling, and multiply during feed out. Chemical additives traditionally have fallen in 2 groups. Formic acid causes direct acidification, suppressing clostridia and other undesired bacteria and improving protein preservation during ensiling. On the other hand, sorbic, benzoic, propionic, and acetic acids improve silage aerobic stability at feed out through direct inhibition of yeasts and molds. Current research has focused on various combinations of these chemicals to improve both aerobic stability and animal productivity. Enzyme additives have been added to forage primarily to breakdown plant cell walls at ensiling to improve silage fermentation by providing sugars for the LAB and to enhance the nutritive value of silage by increasing the digestibility of cell walls. Cellulase or hemicellulase mixtures have been more successful at the former than the latter. A new approach focused on Lb. buchneri producing ferulic acid esterase has also had mixed success in improving the efficiency of silage digestion. Another new enzyme approach is the application of proteases to corn silage to improve starch digestibility, but more research is needed to determine the feasibility. Future silage additives are expected to directly inhibit clostridia and other detrimental microorganisms, mitigate high mycotoxin levels on harvested forages during ensiling, enhance aerobic stability, improve cell wall digestibility, increase the efficiency of utilization of silage nitrogen by cattle, and increase the availability of starch to cattle. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Quantum-chemical study of antioxidant additives for jet fuels

Energy Technology Data Exchange (ETDEWEB)

Poletaeva, O.Yu. [Ufa State Petroleum Technological Univ., Ufa (Russian Federation); Karimova, R.I. [Bashkir State Agrarian Univ., Ufa (Russian Federation); Movsumzade, E.M. [Institute of Education of Indigenous Small-Numbered Peoples of the North RAE, Moscow (Russian Federation)

2012-07-01

To obtain the necessary quality of jet fuels it can be used technological methods (hydrocracking, deep hydration, hydrogenation) that increases the cost of the finished product. The second way is to use less purified raw materials with the introduction of effective additives. Fuels obtained by direct distillation, in ambient air are oxidized with great difficulty and oxidation products accumulate in them is very slow. Fuels derived by hydrogenation processes, have high susceptibility to oxidation, as a result in 1-2 years of storage considerably reduced their quality. Antioxidant additives play an important role in improving the quality of jet fuel. (orig.)

Dominance genetic variance for traits under directional selection in Drosophila serrata.

Science.gov (United States)

Sztepanacz, Jacqueline L; Blows, Mark W

2015-05-01

In contrast to our growing understanding of patterns of additive genetic variance in single- and multi-trait combinations, the relative contribution of nonadditive genetic variance, particularly dominance variance, to multivariate phenotypes is largely unknown. While mechanisms for the evolution of dominance genetic variance have been, and to some degree remain, subject to debate, the pervasiveness of dominance is widely recognized and may play a key role in several evolutionary processes. Theoretical and empirical evidence suggests that the contribution of dominance variance to phenotypic variance may increase with the correlation between a trait and fitness; however, direct tests of this hypothesis are few. Using a multigenerational breeding design in an unmanipulated population of Drosophila serrata, we estimated additive and dominance genetic covariance matrices for multivariate wing-shape phenotypes, together with a comprehensive measure of fitness, to determine whether there is an association between directional selection and dominance variance. Fitness, a trait unequivocally under directional selection, had no detectable additive genetic variance, but significant dominance genetic variance contributing 32% of the phenotypic variance. For single and multivariate morphological traits, however, no relationship was observed between trait-fitness correlations and dominance variance. A similar proportion of additive and dominance variance was found to contribute to phenotypic variance for single traits, and double the amount of additive compared to dominance variance was found for the multivariate trait combination under directional selection. These data suggest that for many fitness components a positive association between directional selection and dominance genetic variance may not be expected. Copyright © 2015 by the Genetics Society of America.

Ionic liquids as lubricant additives: A review

International Nuclear Information System (INIS)

Zhou, Yan; Qu, Jun

2016-01-01

In pursuit of energy efficiency and durability throughout human history, advances in lubricants have always played important roles. Ionic liquids (ILs) are room-temperature molten salts that possess unique physicochemical properties and have shown great potential in many applications with lubrication as one of the latest. While earlier work (2001–2011) primarily explored the feasibility of using ILs as neat or base lubricants, using ILs as lubricant additives has become the new focal research topic since the breakthrough in ILs’ miscibility in nonpolar hydrocarbon oils in early 2012. This work reviews the recent advances in developing ILs as additives for lubrication with an attempt to correlate among the cationic and anionic structures, oil-solubility, and other relevant physicochemical properties, and lubricating behavior. Effects of the concentration of ILs in lubricants and the compatibility between ILs and other additives in the lubricant formulation on the tribological performance are described followed by a discussion of wear protection mechanism based on tribofilm characterization. As a result, future research directions are suggested at the end.

Validation of Reverse-Engineered and Additive-Manufactured Microsurgical Instrument Prototype.

Science.gov (United States)

Singh, Ramandeep; Suri, Ashish; Anand, Sneh; Baby, Britty

2016-12-01

With advancements in imaging techniques, neurosurgical procedures are becoming highly precise and minimally invasive, thus demanding development of new ergonomically aesthetic instruments. Conventionally, neurosurgical instruments are manufactured using subtractive manufacturing methods. Such a process is complex, time-consuming, and impractical for prototype development and validation of new designs. Therefore, an alternative design process has been used utilizing blue light scanning, computer-aided designing, and additive manufacturing direct metal laser sintering (DMLS) for microsurgical instrument prototype development. Deviations of DMLS-fabricated instrument were studied by superimposing scan data of fabricated instrument with the computer-aided designing model. Content and concurrent validity of the fabricated prototypes was done by a group of 15 neurosurgeons by performing sciatic nerve anastomosis in small laboratory animals. Comparative scoring was obtained for the control and study instrument. T test was applied to the individual parameters and P values for force (P direct application of these additive-manufactured instruments in the operating room requires further validation. © The Author(s) 2016.

Current reversal in a continuously periodic system driven by an additive noise and a multiplicative noise

International Nuclear Information System (INIS)

Wang Canjun; Chen Shibo; Mei Dongcheng

2006-01-01

We study the noise-induce transport and current reversal of Brownian particles in a continuously periodic potential driven by cross correlation between a multiplicative white noise and an additive white noise. We find that directed motion of the Brownian particles can be induced by the correlation between the additive noise and the multiplicative noise. The current reversal and the direction of the current is controlled by the values of the intensity (λ) of the correlated noises and a dimensionless parameter R (R=α/D, D is the intensity of multiplicative noise and α is the intensity of additive noise)

Additive Manufacturing and Business Models: Current Knowledge and Missing Perspectives

Directory of Open Access Journals (Sweden)

Christina Öberg

2018-06-01

Full Text Available Additive manufacturing, that is 3D printing technology, may change the way companies operate their businesses. This article adopts a business model perspective to create an understanding of what we know about these changes. It summarizes current knowledge on additive manufacturing within management and business research, and it discusses future research directions in relation to business models for additive manufacturing. Using the scientific database Web of Science, 116 journal articles were identified. The literature review reveals that most research concerns manufacturing optimization. A more holistic view of the changes that additive manufacturing may bring about for firms is needed, as is more research on changed value propositions, and customer/sales-related issues. The article contributes to previous research by systematically summarizing additive manufacturing research in the business and management literature, and by highlighting areas for further investigation related to the business models of individual firms.

Characterization of Starch Edible Films with Different Essential Oils Addition

Directory of Open Access Journals (Sweden)

Šuput Danijela

2016-12-01

Full Text Available This study investigated properties of starch-based edible films with oregano and black cumin essential oil addition. Essential oils addition positively affected film swelling (decreased due to essential oil addition, mechanical properties (tensile strength decreased while elongation at break increased, and water vapor barrier properties (decreased along with essential oils addition. Control film did not have any biological activity, which proves the need for essential oils addition in order to obtain active packaging. Oregano oil was more effective in terms of biological activity. Endothermal peak, above 200°C, represents total thermal degradation of edible films. Diffraction pattern of control film showed significant destruction of A-type crystal structure. Addition of essential oils resulted in peak shape change: diffraction peaks became narrower. Principal Component Analysis has been used to assess the effect of essential oils addition on final starch-based edible films characteristics with the aim to reveal directions for the film characteristics improvement, since the next phase will be optimal film application for food packaging.

Does the addition of deep breathing exercises to physiotherapy-directed early mobilisation alter patient outcomes following high-risk open upper abdominal surgery? Cluster randomised controlled trial.

Science.gov (United States)

Silva, Y R; Li, S K; Rickard, M J F X

2013-09-01

To investigate whether the inclusion of deep breathing exercises in physiotherapy-directed early mobilisation confers any additional benefit in reducing postoperative pulmonary complications (PPCs) when patients are treated once daily after elective open upper abdominal surgery. This study also compared postoperative outcomes following early and delayed mobilisation. Cluster randomised controlled trial. Single-centre study in a teaching hospital. Eighty-six high-risk patients undergoing elective open upper abdominal surgery. Three groups: early mobilisation (Group A), early mobilisation plus breathing exercises (Group B), and delayed mobilisation (mobilised from third postoperative day) plus breathing exercises (Group C). PPCs and postoperative outcomes [number of days until discharge from physiotherapy, physiotherapy input and length of stay (LOS)]. There was no significant difference in PPCs between Groups A and B. The LOS for Group A {mean 10.7 [standard deviation (SD) 5.0] days} was significantly shorter than the LOS for Groups B [mean 16.7 (SD 9.7) days] and C [mean 15.2 (SD 9.8) days; P=0.036]. The greatest difference was between Groups A and B (mean difference -5.93, 95% confidence interval -10.22 to -1.65; P=0.008). Group C had fewer smokers (26%) and patients with chronic obstructive pulmonary disease (0%) compared with Group B (53% and 14%, respectively). This may have led to fewer PPCs in Group C, but the difference was not significant. Despite Group C having fewer PPCs and less physiotherapy input, the number of days until discharge from physiotherapy and LOS were similar to Group B. The addition of deep breathing exercises to physiotherapy-directed early mobilisation did not further reduce PPCs compared with mobility alone. PPCs can be reduced with once-daily physiotherapy if the patients are mobilised to a moderate level of exertion. Delayed mobilisation tended to increase physiotherapy input and the number of days until discharge from physiotherapy

Modulation of orientation-selective neurons by motion: when additive, when multiplicative?

Directory of Open Access Journals (Sweden)

Torsten eLüdge

2014-06-01

Full Text Available The recurrent interaction among orientation-selective neurons in the primary visual cortex (V1 is suited to enhance contours in a noisy visual scene. Motion is known to have a strong pop-up effect in perceiving contours, but how motion-sensitive neurons in V1 support contour detection remains vastly elusive. Here we suggest how the various types of motion-sensitive neurons observed in V1 should be wired together in a micro-circuitry to optimally extract contours in the visual scene. Motion-sensitive neurons can be selective about the direction of motion occurring at some spot or respond equally to all directions (pandirectional. We show that, in the light of figure-ground segregation, direction-selective motion neurons should additively modulate the corresponding orientation-selective neurons with preferred orientation orthogonal to the motion direction. In turn, to maximally enhance contours, pandirectional motion neurons should multiplicatively modulate all orientation-selective neurons with co-localized receptive fields. This multiplicative modulation amplifies the local V1-circuitry among co-aligned orientation-selective neurons for detecting elongated contours. We suggest that the additive modulation by direction- specific motion neurons is achieved through synaptic projections to the somatic region, and the multiplicative modulation by pandirectional motion neurons through projections to the apical region of orientation-specific pyramidal neurons. For the purpose of contour detection, the V1- intrinsic integration of motion information is advantageous over a downstream integration as it exploits the recurrent V1-circuitry designed for that task.

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences. Ying Tang. Articles written in Journal of Chemical Sciences. Volume 125 Issue 2 March 2013 pp 313-320. Modified calcium oxide as stable solid base catalyst for Aldol condensation reaction · Ying Tang Jingfang Xu Xuefan Gu · More Details Abstract Fulltext PDF. A highly ...

Effects of additives on solidification of API separator sludge.

Science.gov (United States)

Faschan, A; Tittlebaum, M; Cartledge, F; Eaton, H

1991-08-01

API separator sludge was solidified with various combinations of binders and absorbent soil additives. The binders utilized were Type I Portland Cement, Type C Flyash, and a 1:1 combination of the two. The soil additives used were bentonite, diatomite, Fuller's earth, and two brands of chemically altered bentonites, or organoclays. The effectiveness of the solidification materials was based on their effect on the physical and leaching characteristics of the sludge.It was determined the Portland cement and combination binders provided the sludge with adequate physical and strength characteristics. It was also determined the affinity of each additive for water had an important influence on the physical characteristics of the solidified sludge. The results of the leaching procedure indicated the binders alone reduced the leachability of organic constituents from the sludge by 1/5 to 1/10. It appeared the use of the additives with the binders may have further reduced the leachability of constituents from sludge, with the incorporation of the organoclay additives further reducing leachability by up to 1/2. Also, it appeared the absorbing capacity of the additives was directly related to their ability to reduce the leachability of organic constituents from the sludge.

In-Line Inspection of Additive Manufactured Parts Using Laser Ultrasonics, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Additive manufacturing (AM) is an increasingly popular technique for rapid, low-cost production of parts directly from a CAD file. AM is especially appealing for...

Grain Structure Control of Additively Manufactured Metallic Materials

Directory of Open Access Journals (Sweden)

Fuyao Yan

2017-11-01

Full Text Available Grain structure control is challenging for metal additive manufacturing (AM. Grain structure optimization requires the control of grain morphology with grain size refinement, which can improve the mechanical properties of additive manufactured components. This work summarizes methods to promote fine equiaxed grains in both the additive manufacturing process and subsequent heat treatment. Influences of temperature gradient, solidification velocity and alloy composition on grain morphology are discussed. Equiaxed solidification is greatly promoted by introducing a high density of heterogeneous nucleation sites via powder rate control in the direct energy deposition (DED technique or powder surface treatment for powder-bed techniques. Grain growth/coarsening during post-processing heat treatment can be restricted by presence of nano-scale oxide particles formed in-situ during AM. Grain refinement of martensitic steels can also be achieved by cyclic austenitizing in post-processing heat treatment. Evidently, new alloy powder design is another sustainable method enhancing the capability of AM for high-performance components with desirable microstructures.

Characterization of plastic and boron carbide additive manufactured neutron collimators

Science.gov (United States)

Stone, M. B.; Siddel, D. H.; Elliott, A. M.; Anderson, D.; Abernathy, D. L.

2017-12-01

Additive manufacturing techniques allow for the production of materials with complicated geometries with reduced costs and production time over traditional methods. We have applied this technique to the production of neutron collimators for use in thermal and cold neutron scattering instrumentation directly out of boron carbide. We discuss the design and generation of these collimators. We also provide measurements at neutron scattering beamlines which serve to characterize the performance of these collimators. Additive manufacturing of parts using neutron absorbing material may also find applications in radiography and neutron moderation.

Additivity of entropic uncertainty relations

Directory of Open Access Journals (Sweden)

René Schwonnek

2018-03-01

Full Text Available We consider the uncertainty between two pairs of local projective measurements performed on a multipartite system. We show that the optimal bound in any linear uncertainty relation, formulated in terms of the Shannon entropy, is additive. This directly implies, against naive intuition, that the minimal entropic uncertainty can always be realized by fully separable states. Hence, in contradiction to proposals by other authors, no entanglement witness can be constructed solely by comparing the attainable uncertainties of entangled and separable states. However, our result gives rise to a huge simplification for computing global uncertainty bounds as they now can be deduced from local ones. Furthermore, we provide the natural generalization of the Maassen and Uffink inequality for linear uncertainty relations with arbitrary positive coefficients.

Direct Methanol Fuel Cell, DMFC

Directory of Open Access Journals (Sweden)

Amornpitoksuk, P.

2003-09-01

Full Text Available Direct Methanol Fuel Cell, DMFC is a kind of fuel cell using methanol as a fuel for electric producing. Methanol is low cost chemical substance and it is less harmful than that of hydrogen fuel. From these reasons it can be commercial product. The electrocatalytic reaction of methanol fuel uses Pt-Ru metals as the most efficient catalyst. In addition, the property of membrane and system designation are also effect to the fuel cell efficient. Because of low power of methanol fuel cell therefore, direct methanol fuel cell is proper to use for the energy source of small electrical devices and vehicles etc.

Additions to the barnacle (Crustacea: Cirripedia) fauna of South Africa

African Journals Online (AJOL)

The purpose of this paper is to document recent additions to the South African barnacle (Cirripedia) fauna. New species records were obtained by examining accumulated collections of unidentified material in the Iziko South African Museum, as well as via material collected directly by the authors. Fourteen species, none of ...

A method for additive bias correction in cross-cultural surveys

DEFF Research Database (Denmark)

Scholderer, Joachim; Grunert, Klaus G.; Brunsø, Karen

2001-01-01

additive bias from cross-cultural data. The procedure involves four steps: (1) embed a potentially biased item in a factor-analytic measurement model, (2) test for the existence of additive bias between populations, (3) use the factor-analytic model to estimate the magnitude of the bias, and (4) replace......Measurement bias in cross-cultural surveys can seriously threaten the validity of hypothesis tests. Direct comparisons of means depend on the assumption that differences in observed variables reflect differences in the underlying constructs, and not an additive bias that may be caused by cultural...... differences in the understanding of item wording or response category labels. However, experience suggests that additive bias can be found more often than not. Based on the concept of partial measurement invariance (Byrne, Shavelson and Muthén, 1989), the present paper develops a procedure for eliminating...

What Is Direct-to-Consumer Genetic Testing?

Science.gov (United States)

... consumer genetic testing. Additional information about direct-to-consumer marketing of genetic tests and related research questions are ... for Links Data Files & API Site Map Subscribe Customer Support USA.gov Copyright Privacy Accessibility FOIA Viewers & ...

Biodiesel production from tall oil with synthesized Mn and Ni based additives: effects of the additives on fuel consumption and emissions

Energy Technology Data Exchange (ETDEWEB)

Ali Keskin; Metin Guru; Duran Altiparmak [Mersin University, Mersin (Turkey). Technical Education Faculty

2007-05-15

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO{sub 2} stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 {mu}mol/l and 12 {mu}mol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NOx emission was also observed in general for the biodiesel fuels. 28 refs., 4 figs., 3 tabs.

Infinite additional symmetries in the two-dimensional conformal quantum field theory

International Nuclear Information System (INIS)

Apikyan, S.A.

1987-01-01

Additional symmetries in the two-dimensional conformal field theory, generated by currents (2,3/2,5/2) and (2,3/2,3) have been studied. It has been shown that algebra (2,3/2,5/2) is the direct product of algebras (2,3/2) and (2,5/2), and algebra (2,3/2,3) is the direct product of algebras (2,3/2) and (2,3). Associative algebra, formed by multicomponent symmetry generators of spin 3 for SO(3) has also been found

The Additional Professional Training in the Late Russian Empire

Directory of Open Access Journals (Sweden)

Timur A. Magsumov

2015-06-01

Full Text Available The article reveals the experience of intensive organization and functioning of the system of additional professional training in the late imperial period of the Russian history, generated by the need of unfolded modernization in the country. The article is written on the basis of mass sources, including the regional archives of record keeping documentation and working in the mainstream of the study of basic organizational forms of additional training - agricultural courses, shopping classes and courses of technical drawing, also the author produces a macro shot of trends and directions, successes and challenges in its development. The additional professional training as a specific element of the education system of 20th century focusing on the real sector of economy has implemented the free practice-training based on the principles of interdisciplinarity, variability and the high role of self-education.

In-situ acoustic signature monitoring in additive manufacturing processes

Science.gov (United States)

Koester, Lucas W.; Taheri, Hossein; Bigelow, Timothy A.; Bond, Leonard J.; Faierson, Eric J.

2018-04-01

Additive manufacturing is a rapidly maturing process for the production of complex metallic, ceramic, polymeric, and composite components. The processes used are numerous, and with the complex geometries involved this can make quality control and standardization of the process and inspection difficult. Acoustic emission measurements have been used previously to monitor a number of processes including machining and welding. The authors have identified acoustic signature measurement as a potential means of monitoring metal additive manufacturing processes using process noise characteristics and those discrete acoustic emission events characteristic of defect growth, including cracks and delamination. Results of acoustic monitoring for a metal additive manufacturing process (directed energy deposition) are reported. The work investigated correlations between acoustic emissions and process noise with variations in machine state and deposition parameters, and provided proof of concept data that such correlations do exist.

Additive Biotech-Chances, challenges, and recent applications of additive manufacturing technologies in biotechnology.

Science.gov (United States)

Krujatz, Felix; Lode, Anja; Seidel, Julia; Bley, Thomas; Gelinsky, Michael; Steingroewer, Juliane

2017-10-25

The diversity and complexity of biotechnological applications are constantly increasing, with ever expanding ranges of production hosts, cultivation conditions and measurement tasks. Consequently, many analytical and cultivation systems for biotechnology and bioprocess engineering, such as microfluidic devices or bioreactors, are tailor-made to precisely satisfy the requirements of specific measurements or cultivation tasks. Additive manufacturing (AM) technologies offer the possibility of fabricating tailor-made 3D laboratory equipment directly from CAD designs with previously inaccessible levels of freedom in terms of structural complexity. This review discusses the historical background of these technologies, their most promising current implementations and the associated workflows, fabrication processes and material specifications, together with some of the major challenges associated with using AM in biotechnology/bioprocess engineering. To illustrate the great potential of AM, selected examples in microfluidic devices, 3D-bioprinting/biofabrication and bioprocess engineering are highlighted. Copyright © 2017 Elsevier B.V. All rights reserved.

Direct and semi-direct radiative forcing of smoke aerosols over clouds

Directory of Open Access Journals (Sweden)

E. M. Wilcox

2012-01-01

Full Text Available Observations from Earth observing satellites indicate that dark carbonaceous aerosols that absorb solar radiation are widespread in the tropics and subtropics. When these aerosols mix with clouds, there is generally a reduction of cloudiness owing to absorption of solar energy in the aerosol layer. Over the subtropical South Atlantic Ocean, where smoke from savannah burning in southern Africa resides above a persistent deck of marine stratocumulus clouds, radiative heating of the smoke layer leads to a thickening of the cloud layer. Here, satellite observations of the albedo of overcast scenes of 25 km² size or larger are combined with additional satellite observations of clouds and aerosols to estimate the top-of-atmosphere direct radiative forcing attributable to presence of dark aerosol above bright cloud, and the negative semi-direct forcing attributable to the thickening of the cloud layer. The average positive direct radiative forcing by smoke over an overcast scene is 9.2±6.6 W m⁻² for cases with an unambiguous signal of absorbing aerosol over cloud in passive ultraviolet remote sensing observations. However, cloud liquid water path is enhanced by 16.3±7.7 g m⁻² across the range of values for sea surface temperature for cases of smoke over cloud. The negative radiative forcing associated with this semi-direct effect of smoke over clouds is estimated to be −5.9±3.5 W m⁻². Therefore, the cooling associated with the semi-direct cloud thickening effect compensates for greater than 60 % of the direct radiative effect. Accounting for the frequency of occurrence of significant absorbing aerosol above overcast scenes leads to an estimate of the average direct forcing of 1.0±0.7 W m⁻² contributed by these scenes averaged over the subtropical southeast Atlantic Ocean during austral winter. The regional average of the negative semi-direct forcing is −0.7±0.4 W m⁻²

On the tandem Morita-Baylis-Hillman/transesterification processes. Mechanistic insights for the role of protic solvents

Science.gov (United States)

Carpanez, Arthur G.; Coelho, Fernando; Amarante, Giovanni W.

2018-02-01

Despite the remarkable rate acceleration under protic solvents such as alcohols and water, the use of acrylates as activated alkenes places a problem due to the possibility of ester hydrolysis or transesterification. Therefore, the tandem transesterification/Morita-Baylis-Hillman (MBH) reactions were investigated by ESI(+)-MS/(MS) and 1H NMR techniques. For the first time, the MBH back-reaction was fully examined by ESI(+)-MS/(MS) using labelling reagents revealed the complex equilibrium involving the Michael-type addition step of DABCO to acrylate. C- and O-protonation were observed at this stage, showing the transesterification process occurs previous to the aldol step, which is the rate-determining step of the mechanism. At this stage, a short-lived tetrahedral intermediate might be involved and should be considered in these processes.

Influence of Catalyst Acid/Base Properties in Acrolein Production by Oxidative Coupling of Ethanol and Methanol.

Science.gov (United States)

Lilić, Aleksandra; Bennici, Simona; Devaux, Jean-François; Dubois, Jean-Luc; Auroux, Aline

2017-05-09

Oxidative coupling of methanol and ethanol represents a new route to produce acrolein. In this work, the overall reaction was decoupled in two steps, the oxidation and the aldolization, by using two consecutive reactors to investigate the role of the acid/base properties of silica-supported oxide catalysts. The oxidation of a mixture of methanol and ethanol to formaldehyde and acetaldehyde was performed over a FeMoO x catalyst, and then the product mixture was transferred without intermediate separation to a second reactor, in which the aldol condensation and dehydration to acrolein were performed over the supported oxides. The impact of the acid/base properties on the selectivity towards acrolein was investigated under oxidizing conditions for the first time. The acid/base properties of the catalysts were investigated by NH 3 -, SO 2 -, and methanol-adsorption microcalorimetry. A MgO/SiO 2 catalyst was the most active in acrolein production owing to an appropriate ratio of basic to acidic sites. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of Renewable Lubricant Alkanes from Biomass-Derived Platform Chemicals.

Science.gov (United States)

Gu, Mengyuan; Xia, Qineng; Liu, Xiaohui; Guo, Yong; Wang, Yanqin

2017-10-23

The catalytic synthesis of liquid alkanes from renewable biomass has received tremendous attention in recent years. However, bio-based platform chemicals have not to date been exploited for the synthesis of highly branched lubricant alkanes, which are currently produced by hydrocracking and hydroisomerization of long-chain n-paraffins. A selective catalytic synthetic route has been developed for the production of highly branched C 23 alkanes as lubricant base oil components from biomass-derived furfural and acetone through a sequential four-step process, including aldol condensation of furfural with acetone to produce a C 13 double adduct, selective hydrogenation of the adduct to a C 13 ketone, followed by a second condensation of the C 13 ketone with furfural to generate a C 23 aldol adduct, and finally hydrodeoxygenation to give highly branched C 23 alkanes in 50.6 % overall yield from furfural. This work opens a general strategy for the synthesis of high-quality lubricant alkanes from renewable biomass. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Additive Cellular Automata and Volume Growth

Directory of Open Access Journals (Sweden)

Thomas B. Ward

2000-08-01

Full Text Available Abstract: A class of dynamical systems associated to rings of S-integers in rational function fields is described. General results about these systems give a rather complete description of the well-known dynamics in one-dimensional additive cellular automata with prime alphabet, including simple formulæ for the topological entropy and the number of periodic configurations. For these systems the periodic points are uniformly distributed along some subsequence with respect to the maximal measure, and in particular are dense. Periodic points may be constructed arbitrarily close to a given configuration, and rationality of the dynamical zeta function is characterized. Throughout the emphasis is to place this particular family of cellular automata into the wider context of S-integer dynamical systems, and to show how the arithmetic of rational function fields determines their behaviour. Using a covering space the dynamics of additive cellular automata are related to a form of hyperbolicity in completions of rational function fields. This expresses the topological entropy of the automata directly in terms of volume growth in the covering space.

75 FR 37733 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-06-30

... Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program AGENCY... direct final rule to amend the Renewable Fuel Standard program requirements on May 10, 2010. Because EPA... Fuel Standard program requirements, published on May 10, 2010. We stated in that direct final rule that...

Apparent directional selection by biased pleiotropic mutation.

Science.gov (United States)

Tanaka, Yoshinari

2010-07-01

Pleiotropic effects of deleterious mutations are considered to be among the factors responsible for genetic constraints on evolution by long-term directional selection acting on a quantitative trait. If pleiotropic phenotypic effects are biased in a particular direction, mutations generate apparent directional selection, which refers to the covariance between fitness and the trait owing to a linear association between the number of mutations possessed by individuals and the genotypic values of the trait. The present analysis has shown how the equilibrium mean value of the trait is determined by a balance between directional selection and biased pleiotropic mutations. Assuming that genes act additively both on the trait and on fitness, the total variance-standardized directional selection gradient was decomposed into apparent and true components. Experimental data on mutation bias from the bristle traits of Drosophila and life history traits of Daphnia suggest that apparent selection explains a small but significant fraction of directional selection pressure that is observed in nature; the data suggest that changes induced in a trait by biased pleiotropic mutation (i.e., by apparent directional selection) are easily compensated for by (true) directional selection.

The Development of High Temperature Thermoplastic Composite Materials for Additive Manufactured Autoclave Tooling

Energy Technology Data Exchange (ETDEWEB)

Kunc, Vlastimil [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Duty, Chad E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lindahl, John M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hassen, Ahmed A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

In this work, ORNL and Techmer investigated and screened different high temperature thermoplastic reinforced materials to fabricate composite molds for autoclave processes using Additive Manufacturing (AM) techniques. This project directly led to the development and commercial release of two printable, high temperature composite materials available through Techmer PM. These new materials are targeted for high temperature tooling made via large scale additive manufacturing.

Physico-mechanical and dissolution behaviours of ibuprofen crystals crystallized in the presence of various additives

Directory of Open Access Journals (Sweden)

A Nokhodchi

2010-06-01

Full Text Available "n  "n Background and the purpose of the study: The success of any direct-tableting procedure is strongly affected by the quality of the crystals used in the process. Ibuprofen is a poorly compactible drug with a high tendency for capping. In order to use ibuprofen in direct compression formulations, physico-mechanical properties of ibuprofen should be improved considerably. The aim of the present investigation was to employ crystallization techniques in order to improve the physico-mechanical properties of ibuprofen for direct compression. "nMethods:The experimental methods involved the preparation of ibuprofen crystals by solvent change technique. Ibuprofen was dissolved in ethanol and crystallized out with water in the absence or presence of various hydrophilic additives (PEG 6000, 8000, Brij 98P and polyvinyl alcohol 22000, PVA 22000 with different concentrations. The physico-mechanical properties of the ibuprofen crystals were studied in terms of flow, density, tensile strength and dissolution behaviour. Morphology of ibuprofen crystals was studied by scanning electron microscopic (SEM. Solid state of the recrystallized particles was also investigated using differential scanning calorimeter (DSC and FT-IR. "nResults:Ibuprofen samples crystallized in the presence of PEG 6000 and 8000 and PVA showed remarkable increase in the tensile strengths of the directly compressed tablets, while some other additives, i.e. Brij 98P did not produce improved ibuprofen crystals. Ibuprofen powders made from particles obtained in the presence of PVA and Brij 98P showed similar dissolution profiles to the commercial ibuprofen particles. DSC and FT-IR results ruled out any significant interaction between ibuprofen and additives except for the samples crystallized in the presence of PEG 8000. Conclusion:The crystal habit of ibuprofen can be altered successfully by the crystallization technique which was developed in this study. The crystals developed in the

Characterization of Metal Powders Used for Additive Manufacturing.

Science.gov (United States)

Slotwinski, J A; Garboczi, E J; Stutzman, P E; Ferraris, C F; Watson, S S; Peltz, M A

2014-01-01

Additive manufacturing (AM) techniques can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process.

Characterization of Metal Powders Used for Additive Manufacturing

Science.gov (United States)

Slotwinski, JA; Garboczi, EJ; Stutzman, PE; Ferraris, CF; Watson, SS; Peltz, MA

2014-01-01

Additive manufacturing (AM) techniques1 can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process. PMID:26601040

Reduced Nutrient Excretion and Environmental Microbial Load with the Addition of a Combination of Enzymes and Direct-Fed Microbials to the Diet of Broiler Chickens

Directory of Open Access Journals (Sweden)

MFFM Praes

2016-03-01

Full Text Available Abstract This study evaluated the effects of the dietary inclusion of an enzyme blend and a direct-fed microbials in broiler diets on litter production and quality. In total, 900 Cobb 500(r broiler chicks were distributed according to a completely randomized design into 4 treatments and 9 replicates of 25 birds each. Broilers were reared from 1 to 42 days of age. The treatments consisted of the following diets: NC: negative control; DFM: NC + 500 ppm of direct-fed microbials product (DFM, containing Bacillus subtilis and Bacillus licheniformis; ENZ: diet formulated with an enzyme blend (20 ppm phytase, 200 ppm protease and 200 ppm of xylanase; DFM+E: ENZ + DFM. Birds and litter were weighed at the start and end of the rearing period, for litter production and waste ratio (Rw determination. Litter samples were analyzed for dry matter (DM content, total and thermotolerant coliform counts, nutrient composition (nitrogen (N, phosphorous (P and potassium (K, and fiber fraction (neutral detergent fiber (NDF, acid detergent fiber (ADF and lignin. The dietary inclusion of the evaluated additivesdid not influence litter production or Rw; however, ADF (%, NDF (kg and kg/kg DM litter, and total and thermotolerant coliform counts were reduced, and N content increased in the litter. The diets containing enzymes (ENZ and DFM+E reduced litter P content. The addition of exogenous enzymes and their combination with a DFM based on Bacillus spp .Did not affect waste production, and reduced litter microbial load, and the contents of P and insoluble fiber in the litter.

Facile Condensation of Aromatic Aldehydes with Chroman-4-ones and 1-Thiochroman-4-ones Catalysed by Amberlyst-15 under Microwave Irradiation Condition

Directory of Open Access Journals (Sweden)

Tapas K. Mandal

2011-01-01

Full Text Available Different aromatic aldehydes and cinnamaldehyde undergo cross-aldol condensation with chroman-4-ones and1-thiochroman-4-ones in the presence of amberlyst-15 under microwave irradiation in solvent free condition to afford rapidly the corresponding E-3-arylidene and E-3-cinnamylidene derivatives, respectively, in high yield. This process is simple, efficient and environmentally benign.

Total synthesis of (3S, 5R, 3'S, 5'R)-capsorubin

International Nuclear Information System (INIS)

Frederico, Daniel; Constantino, Mauricio G.; Donate, Paulo M.

2009-01-01

The total synthesis of enantiomerically enriched (3S, 5R, 3'S, 5'R)-capsorubin (1) by aldol condensation of (1R, 4S)-1-(4-hydroxy-1,2,2-trimethyl-cyclopentyl)ethanone (2a) and crocetindial (3) is described. An alternative, short eight-step synthesis of the optically active compound 2a (ee 89%) is also reported. (author)

Current limiting characteristics of transformer type SFCL with coupled secondary windings according to its winding direction

Energy Technology Data Exchange (ETDEWEB)

Lim, Sung Hun [Dept. of Electrical Engineering, Soongsil University, Seoul (Korea, Republic of); Han, Tae Hee [Dept. of Aero Materials Engineering, Jungwon University, Goesan (Korea, Republic of)

2017-06-15

In this paper, the current limiting characteristics of the transformer type superconducting fault current limiter (SFCL) with the two coupled secondary windings due to its winding direction were analyzed. To analyze the dependence of transient fault current limiting characteristics on the winding direction of the additional secondary winding, the fault current limiting tests of the SFCL with an additional secondary winding, wound as subtractive polarity winding and additive polarity winding, were carried out. The time interval of quench occurrence between two superconducting elements comprising the transformer type SFCL with the additional secondary winding was confirmed to be affected by the winding direction of the additional secondary winding. In case of the subtractive polarity winding of the additional secondary winding, the time interval of the quench occurrence in two superconducting elements was shorter than the case of the additive polarity winding.

Current limiting characteristics of transformer type SFCL with coupled secondary windings according to its winding direction

International Nuclear Information System (INIS)

Lim, Sung Hun; Han, Tae Hee

2017-01-01

In this paper, the current limiting characteristics of the transformer type superconducting fault current limiter (SFCL) with the two coupled secondary windings due to its winding direction were analyzed. To analyze the dependence of transient fault current limiting characteristics on the winding direction of the additional secondary winding, the fault current limiting tests of the SFCL with an additional secondary winding, wound as subtractive polarity winding and additive polarity winding, were carried out. The time interval of quench occurrence between two superconducting elements comprising the transformer type SFCL with the additional secondary winding was confirmed to be affected by the winding direction of the additional secondary winding. In case of the subtractive polarity winding of the additional secondary winding, the time interval of the quench occurrence in two superconducting elements was shorter than the case of the additive polarity winding

Direct Amination of alpha-Hydroxy Amides

NARCIS (Netherlands)

Chandgude, Ajay L.; Dömling, Alexander

A TiCl4-mediated reaction for the direct amination of alpha-hydroxy amides has been developed. This simple, general, additive/base/ligand-free reaction is mediated by economical TiCl4. The reaction runs under mild conditions. This highly efficient C-N bond formation protocol is valid for diverse

Towards direction dependent fluxes with AMS-02

Energy Technology Data Exchange (ETDEWEB)

Zeissler, Stefan; Andeen, Karen; Boer, Wim de; Gebauer, Iris; Merx, Carmen; Nikonov, Nikolay; Vagelli, Valerio [Karlsruher Institut fuer Technologie KIT (Germany)

2015-07-01

The Alpha Magnetic Spectrometer (AMS-02) is a state-of-the-art particle physics detector designed to operate as an external module on the International Space Station (ISS). In the unique space environment cosmic particles can be measured with high precision over an energy range from GeV up to TeV. In 2014 electron and positron flux measurements where published which indicate an additional source of positrons among the various cosmic particles. The arrival directions of energetic positrons and electrons convey fundamental information on their origin. We evaluate the AMS-02 detector acceptance for each incoming particle direction and show preliminary results of a direction dependent measurement of the AMS-02 lepton flux.

Effect of Refiner Addition Level on Zirconium-Containing Aluminium Alloys

International Nuclear Information System (INIS)

Jaradeh, M M R; Carlberg, T

2012-01-01

It is well known that in aluminium alloys containing Zr, grain refiner additions do not function as desired, producing an effect often referred to as nuclei poisoning. This paper investigates the structure of direct chill-cast ingots of commercial AA3003 aluminium alloys, with and without Zr, at various addition levels of Al5Ti1B master alloy. In Bridgman experiments simulating ingot solidification, Zr-containing alloys were studied after the addition of various amounts of Ti. It could be demonstrated, in both ingot casting and simulation experiments, that Zr poisoning can be compensated for by adding more Ti and/or Al5Ti1B. The results confirm better refinement behaviour with the addition of Ti + B than of only Ti. The various combinations of Zr and Ti also influenced the formation of AlFeMn phases, and the precipitation of large Al 6 (Mn,Fe) particles was revealed. AlZrTiSi intermetallic compounds were also detected.

Effect of Refiner Addition Level on Zirconium-Containing Aluminium Alloys

Science.gov (United States)

Jaradeh, M. M. R.; Carlberg, T.

2012-01-01

It is well known that in aluminium alloys containing Zr, grain refiner additions do not function as desired, producing an effect often referred to as nuclei poisoning. This paper investigates the structure of direct chill-cast ingots of commercial AA3003 aluminium alloys, with and without Zr, at various addition levels of Al5Ti1B master alloy. In Bridgman experiments simulating ingot solidification, Zr-containing alloys were studied after the addition of various amounts of Ti. It could be demonstrated, in both ingot casting and simulation experiments, that Zr poisoning can be compensated for by adding more Ti and/or Al5Ti1B. The results confirm better refinement behaviour with the addition of Ti + B than of only Ti. The various combinations of Zr and Ti also influenced the formation of AlFeMn phases, and the precipitation of large Al6(Mn,Fe) particles was revealed. AlZrTiSi intermetallic compounds were also detected.

Defense Forensics: Additional Planning and Oversight Needed to Establish an Enduring Expeditionary Forensic Capability

Science.gov (United States)

2013-06-01

forensic pathology, forensic anthropology, and forensic toxicology . 13DOD’s forensic directive defines DOD components as the Office of the...DEFENSE FORENSICS Additional Planning and Oversight Needed to Establish an Enduring Expeditionary Forensic ...COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE Defense Forensics : Additional Planning and Oversight Needed to Establish an Enduring

DIRECT SALES IN THE CONTEXT OF ROMANIA'S UE INTEGRATION

Directory of Open Access Journals (Sweden)

Gherman Cristina

2010-12-01

Full Text Available More recently, direct sales business is stimulated by the difficult market conditions. While retailers hardly bear fixed costs such as rent, administrative costs and tend to raise prices, customers fall back to products offered by direct sale. In addition, labour market conditions made more and more Romanians (who were left without incomes to move towards this system. On the other hand, the direct sales field doesnt concern only those who remained without a job, but rather those who want to round their incomes.

The behaviour of molybdenum dialkyldithiocarbamate friction modifier additives

International Nuclear Information System (INIS)

Graham, Jocelyn Claire Herries

2001-01-01

In recent years there has been growing concern to produce energy-efficient lubricated components and modem engine oil specifications require lubricants to demonstrate fuel efficiency in standardised engine tests. One important method of producing low friction and thus fuel-efficient lubricants is to use oil-soluble, molybdenum-containing, friction modifier additives. In optimal conditions these additives are able to produce very low friction coefficients, in the range 0.045 to 0.075 in boundary lubrication conditions. Very little is known about the chemical and physical mechanisms by which oil soluble molybdenum additives form low friction films in tribological contacts. Information about their activity could lead to optimal use of these additives in lubricants and, therefore, more efficient engine running. The work outlined in this thesis investigated the behaviour of oil-soluble molybdenum additives and showed that these additives were able to effectively reduce friction in the absence of other additives such as ZnDTP. Their activity was shown to be highly concentration and temperature dependent and was also found to be sensitive to the roughness of the contacting surfaces. Raman spectroscopy was used to analyse the chemical nature of molybdenum-containing reaction films and found that friction reduction indubitably arises from the local formation of platelets (diameter 30-50 nm) of MoS 2 . The formation of MoS 2 -rich films was found to occur only during direct asperity-asperity rubbing of the contacting surfaces (this type of contact being especially prevalent in pure sliding contacts). At elevated temperatures and in the presence of oxidising gases the consumption of MoDTC was monitored. MoDTC concentration dropped until the total value fell below a critical level to reduce friction. The study showed that decay rate of molybdenum-containing species was reduced by the addition of peroxide-decomposing antioxidants. (author)

Directed Forgetting in Direct and Indirect Tests of Memory: Seeking Evidence of Retrieval Inhibition Using Electrophysiological Measures

Science.gov (United States)

Van Hooff, Johanna C.; Whitaker, T. Aisling; Ford, Ruth M.

2009-01-01

We investigated whether directed forgetting as elicited by the item-cueing method results solely from "differential rehearsal" of to-be-remembered vs. to-be-forgotten words or, additionally, from "inhibitory" processes that actively impair retrieval of to-be-forgotten words. During study, participants (N = 24) were instructed to remember half of a…

A procedure for eliminating additive bias from cross-cultural survey data

DEFF Research Database (Denmark)

Scholderer, Joachim; Grunert, Klaus G.; Brunsø, Karen

2005-01-01

additive bias from cross-cultural data. The procedure involves four steps: (1) embed a potentially biased item in a factor-analytic measurement model, (2) test for the existence of additive bias between populations, (3) use the factor-analytic model to estimate the magnitude of the bias, and (4) replace......Measurement bias in cross-cultural surveys can seriously threaten the validity of hypothesis tests. Direct comparisons of means depend on the assumption that differences in observed variables reflect differences in the underlying constructs, and not an additive bias that may be caused by cultural...... differences in the understanding of item wording or response category labels. However, experience suggests that additive bias can be found more often than not. Based on the concept of partial measurement invariance (Byrne, Shavelson and Muthén 1989), the present paper develops a procedure for eliminating...

Additive Manufacturing Design Considerations for Liquid Engine Components

Science.gov (United States)

Whitten, Dave; Hissam, Andy; Baker, Kevin; Rice, Darron

2014-01-01

The Marshall Space Flight Center's Propulsion Systems Department has gained significant experience in the last year designing, building, and testing liquid engine components using additive manufacturing. The department has developed valve, duct, turbo-machinery, and combustion device components using this technology. Many valuable lessons were learned during this process. These lessons will be the focus of this presentation. We will present criteria for selecting part candidates for additive manufacturing. Some part characteristics are 'tailor made' for this process. Selecting the right parts for the process is the first step to maximizing productivity gains. We will also present specific lessons we learned about feature geometry that can and cannot be produced using additive manufacturing machines. Most liquid engine components were made using a two-step process. The base part was made using additive manufacturing and then traditional machining processes were used to produce the final part. The presentation will describe design accommodations needed to make the base part and lessons we learned about which features could be built directly and which require the final machine process. Tolerance capabilities, surface finish, and material thickness allowances will also be covered. Additive Manufacturing can produce internal passages that cannot be made using traditional approaches. It can also eliminate a significant amount of manpower by reducing part count and leveraging model-based design and analysis techniques. Information will be shared about performance enhancements and design efficiencies we experienced for certain categories of engine parts.

Development of oxygen scavenger additives for jet fuels

Energy Technology Data Exchange (ETDEWEB)

Beaver, B.D.; Demunshi, R.; Sharief, V.; Tian, D.; Teng, Y. [Duquesne Univ., Pittsburgh, PA (United States)

1995-05-01

Our current research program is in response to the US Air Force`s FY93 New Initiative entitled {open_quotes}Advanced Fuel Composition and Use.{close_quotes} The critical goal of this initiative is to develop aircraft fuels which can operate at supercritical conditions. This is a vital objective since future aircraft designs will transfer much higher heat loads into the fuel as compared with current heat loads. In this paper it is argued that the thermal stability of most jet fuels would be dramatically improved by the efficient in flight-removal of a fuel`s dissolved oxygen. It is proposed herein to stabilize the bulk fuel by the addition of an additive which will be judiciously designed and programmed to react with oxygen and produce an innocuous product. It is envisioned that a thermally activated reaction will occur, between the oxygen scavenging additive and dissolved oxygen, in a controlled and directed manner. Consequently formation of insoluble thermal degradation products will be limited. It is believed that successful completion of this project will result in the development of a new type of jet fuel additive which will enable current conventional jet fuels to obtain sufficient thermal stability to function in significantly higher temperature regimes. In addition, it is postulated that the successful development of thermally activated oxygen scavengers will also provide the sub-critical thermal stability necessary for future development of endothermic fuels.

Additive manufacturing of RF absorbers

Science.gov (United States)

Mills, Matthew S.

The ability of additive manufacturing techniques to fabricate integrated electromagnetic absorbers tuned for specific radio frequency bands within structural composites allows for unique combinations of mechanical and electromagnetic properties. These composites and films can be used for RF shielding of sensitive electromagnetic components through in-plane and out-of-plane RF absorption. Structural composites are a common building block of many commercial platforms. These platforms may be placed in situations in which there is a need for embedded RF absorbing properties along with structural properties. Instead of adding radar absorbing treatments to the external surface of existing structures, which adds increased size, weight and cost; it could prove to be advantageous to integrate the microwave absorbing properties directly into the composite during the fabrication process. In this thesis, a method based on additive manufacturing techniques of composites structures with prescribed electromagnetic loss, within the frequency range 1 to 26GHz, is presented. This method utilizes screen printing and nScrypt micro dispensing to pattern a carbon based ink onto low loss substrates. The materials chosen for this study will be presented, and the fabrication technique that these materials went through to create RF absorbing structures will be described. The calibration methods used, the modeling of the RF structures, and the applications in which this technology can be utilized will also be presented.

Synthesis of N,N-Bis(nonaflyl) Squaric Acid Diamide and its Application to Organic Reactions

International Nuclear Information System (INIS)

Cheon, Cheol Hong; Yamamoto, Hisashi

2010-01-01

We have developed a new strong Brφnsted acid bearing two nonaflyl groups based on the squaric acid scaffold. The Brφnsted acid 2 showed the almost same reactivity as bistriflyl squaramide 1 in Mukaiyama aldol and Michael reactions of benzaldehyde with silyl enol ether. Moreover, the utility of Brφnsted acid 2 could be expanded to carbonyl ene reaction of rac-citronellal. Further application of this new Brφnsted acid to organic reactions and to flow system reactors is currently underway in our laboratory. Brφnsted acid catalysis is one of the growing fields in modern organic synthesis.1 Although several Brφnsted acids, such as urea/thiourea, TADDOL, and phosphoric acid, have been applied to a variety of organic reactions, other Brφnsted acid scaffolds have been much less explored. Recently, Rawal et al have developed a Brφnsted acid catalyst based on squaric acid moiety and successfully applied it as a catalyst for conjugate addition of 1,3-dicarbonyl compounds to nitroolefins. More recently, we have developed a strong Brφnsted acid derived from squaric acid by introducing a strong electron withdrawing trifluoromethanesulfonyl (Tf) group and applied it to Mukaiyama aldol and Michael reaction of a variety of aldehydes, ketones, and α,β-unsaturated ketones. As a continuing effort to develop strong Brφnsted acids based on the squaric acid scaffold, it was expected that replacement of Tf group with a longer perfluoro-alkanesulfonyl group would be able to tune the physical properties, such as solubilities in organic solvents and fluoro-philicity, without loss of reactivity. Herein, we report the development of a new Brφnsted acid based on the squaric acid scaffold carrying two nonafluorobutanesulfonyl (Nf) groups and the preliminary results of its reactivity to various organic reactions

Potential for GPC-based laser direct writing

DEFF Research Database (Denmark)

Bañas, Andrew; Glückstad, Jesper

2016-01-01

lasers for such applications by using phase modulation as opposed to amplitude truncating masks. Here, we explore GPC’s potential for increasing the yield of micropscopic 3D printing also known as direct laser writing. Many light based additive manufacturing techniques, adopt a point scanning approach...

Hydroxide Self-Feeding High-Temperature Alkaline Direct Formate Fuel Cells.

Science.gov (United States)

Li, Yinshi; Sun, Xianda; Feng, Ying

2017-05-22

Conventionally, both the thermal degradation of the anion-exchange membrane and the requirement of additional hydroxide for fuel oxidation reaction hinder the development of the high-temperature alkaline direct liquid fuel cells. The present work addresses these two issues by reporting a polybenzimidazole-membrane-based direct formate fuel cell (DFFC). Theoretically, the cell voltage of the high-temperature alkaline DFFC can be as high as 1.45 V at 90 °C. It has been demonstrated that a proof-of-concept alkaline DFFC without adding additional hydroxide yields a peak power density of 20.9 mW cm -2 , an order of magnitude higher than both alkaline direct ethanol fuel cells and alkaline direct methanol fuel cells, mainly because the hydrolysis of formate provides enough OH - ions for formate oxidation reaction. It was also found that this hydroxide self-feeding high-temperature alkaline DFFC shows a stable 100 min constant-current discharge at 90 °C, proving the conceptual feasibility. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Perceptions of self-determination by special education and rehabilitation practitioners based on viewing a self-directed IEP versus an external-directed IEP meeting.

Science.gov (United States)

Branding, Dave; Bates, Paul; Miner, Craig

2009-01-01

This study investigated perception of self-determination by special education and rehabilitation practitioners following their exposure to a videotaped simulation of a self-directed IEP meeting and an external-directed IEP meeting involving an adolescent with mild mental retardation. Groups of special education practitioners and rehabilitation practitioners did not differ from each other in their perceptions of self-determination before or after viewing either the self-directed or external-directed IEP meeting simulation. However, both groups of respondents had higher perceptions of the self-determination capability of the confederate student when they viewed her in a self-directed meeting. In addition, respondents consistently rated the self-directed meeting simulation as being of higher overall quality than the external-directed meeting. Results are discussed in relation to practitioner recommendations and future research in regard to the development and enabling of self-determination skills involving persons with disabilities.

Sodium borohydride as an additive to enhance the performance of direct ethanol fuel cells

Energy Technology Data Exchange (ETDEWEB)

Wang, Lianqin; Fang, Xiang; Shen, Pei Kang [The Key Laboratory of Low-carbon Chemistry and Energy Conservation of Guangdong Province, The State Key Laboratory of Optoelectronic Materials and Technologies, Sun Yat-sen University, Guangzhou 510275 (China); Bambagioni, Valentina; Bevilacqua, Manuela; Bianchini, Claudio; Filippi, Jonathan; Lavacchi, Alessandro; Marchionni, Andrea; Vizza, Francesco [Istituto di Chimica dei Composti Organometallici (ICCOM-CNR), via Madonna del Piano 10, 50019 Sesto Fiorentino, Florence (Italy)

2010-12-15

The effect of adding small quantities (0.1-1 wt.%) of sodium borohydride (NaBH{sub 4}) to the anolyte solution of direct ethanol fuel cells (DEFCs) with membrane-electrode assemblies constituted by nanosized Pd/C anode, Fe-Co cathode and anion-exchange membrane (Tokuyama A006) was investigated by means of various techniques. These include cyclic voltammetry, in situ FTIR spectroelectrochemistry, a study of the performance of monoplanar fuel cells and an analysis of the ethanol oxidation products. A comparison with fuel cells fed with aqueous solutions of ethanol proved unambiguously the existence of a promoting effect of NaBH{sub 4} on the ethanol oxidation. Indeed, the potentiodynamic curves of the ethanol-NaBH{sub 4} mixtures showed higher power and current densities, accompanied by a remarkable increase in the fuel consumption at comparable working time of the cell. A {sup 13}C and {sup 11}B {l_brace}{sup 1}H{r_brace}NMR analysis of the cell exhausts and an in situ FTIR spectroelectrochemical study showed that ethanol is converted selectively to acetate while the oxidation product of NaBH{sub 4} is sodium metaborate (NaBO{sub 2}). The enhancement of the overall cell performance has been explained in terms of the ability of NaBH{sub 4} to reduce the PdO layer on the catalyst surface. (author)

High Temperature 300°C Directional Drilling System

Energy Technology Data Exchange (ETDEWEB)

Chatterjee, Kamalesh [Baker Hughes Oilfield Operations, Houston, TX (United States); Aaron, Dick [Baker Hughes Oilfield Operations, Houston, TX (United States); Macpherson, John [Baker Hughes Oilfield Operations, Houston, TX (United States)

2015-07-31

Many countries around the world, including the USA, have untapped geothermal energy potential. Enhanced Geothermal Systems (EGS) technology is needed to economically utilize this resource. Temperatures in some EGS reservoirs can exceed 300°C. To effectively utilize EGS resources, an array of injector and production wells must be accurately placed in the formation fracture network. This requires a high temperature directional drilling system. Most commercial services for directional drilling systems are rated for 175°C while geothermal wells require operation at much higher temperatures. Two U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) projects have been initiated to develop a 300°C capable directional drilling system, the first developing a drill bit, directional motor, and drilling fluid, and the second adding navigation and telemetry systems. This report is for the first project, “High Temperature 300°C Directional Drilling System, including drill bit, directional motor and drilling fluid, for enhanced geothermal systems,” award number DE-EE0002782. The drilling system consists of a drill bit, a directional motor, and drilling fluid. The DOE deliverables are three prototype drilling systems. We have developed three drilling motors; we have developed four roller-cone and five Kymera® bits; and finally, we have developed a 300°C stable drilling fluid, along with a lubricant additive for the metal-to-metal motor. Metal-to-metal directional motors require coatings to the rotor and stator for wear and corrosion resistance, and this coating research has been a significant part of the project. The drill bits performed well in the drill bit simulator test, and the complete drilling system has been tested drilling granite at Baker Hughes’ Experimental Test Facility in Oklahoma. The metal-to-metal motor was additionally subjected to a flow loop test in Baker Hughes’ Celle Technology Center in Germany, where it ran for more than 100

Bioinspired one-dimensional materials for directional liquid transport.

Science.gov (United States)

Ju, Jie; Zheng, Yongmei; Jiang, Lei

2014-08-19

the direction of water droplet's movement on the prepared A-SSs. In addition, the A-SSs with nonuniform spindle-knots, such as multilevel sized spindle-knots and gradient spindle-knots, further demonstrate integrated directional transport ability for water droplets. Through mimicking the main principle of cactus spines in transporting water droplets, we were able to fabricate both single and array A-CSs, which are able to transport liquid droplets directionally both in air and under water. Lastly, we demonstrated some applications of this directional liquid transport, from aspects of efficient fog collection to oil/water separation. In addition, we showed some potential applications in smart catalysis, tracer substance enrichment, smog removal, and drug delivery.

The total synthesis of calcium atorvastatin.

Science.gov (United States)

Dias, Luiz C; Vieira, Adriano S; Barreiro, Eliezer J

2016-02-21

A practical and convergent asymmetric route to calcium atorvastatin (1) is reported. The synthesis of calcium atorvastatin (1) was performed using the remote 1,5-anti asymmetric induction in the boron-mediated aldol reaction of β-alkoxy methylketone (4) with pyrrolic aldehyde (3) as a key step. Calcium atorvastatin was obtained from aldehyde (3) after 6 steps, with a 41% overall yield.

Plasma dark matter direct detection

Energy Technology Data Exchange (ETDEWEB)

Clarke, J.D.; Foot, R., E-mail: j.clarke5@pgrad.unimelb.edu.au, E-mail: rfoot@unimelb.edu.au [ARC Centre of Excellence for Particle Physics at the Terascale, School of Physics, University of Melbourne, Victoria 3010 Australia (Australia)

2016-01-01

Dark matter in spiral galaxies like the Milky Way may take the form of a dark plasma. Hidden sector dark matter charged under an unbroken U(1)' gauge interaction provides a simple and well defined particle physics model realising this possibility. The assumed U(1)' neutrality of the Universe then implies (at least) two oppositely charged dark matter components with self-interactions mediated via a massless 'dark photon' (the U(1)' gauge boson). In addition to nuclear recoils such dark matter can give rise to keV electron recoils in direct detection experiments. In this context, the detailed physical properties of the dark matter plasma interacting with the Earth is required. This is a complex system, which is here modelled as a fluid governed by the magnetohydrodynamic equations. These equations are numerically solved for some illustrative examples, and implications for direct detection experiments discussed. In particular, the analysis presented here leaves open the intriguing possibility that the DAMA annual modulation signal is due primarily to electron recoils (or even a combination of electron recoils and nuclear recoils). The importance of diurnal modulation (in addition to annual modulation) as a means of probing this kind of dark matter is also emphasised.

Improvement of aquaponic performance through micro- and macro-nutrient addition.

Science.gov (United States)

Ru, Dongyun; Liu, Jikai; Hu, Zhen; Zou, Yina; Jiang, Liping; Cheng, Xiaodian; Lv, Zhenting

2017-07-01

Aquaponics is one of the "zero waste" industry in the twenty-first century, and is considered to be one of the major trends for the future development of agriculture. However, the low nitrogen utilization efficiency (NUE) restricted its widely application. To date, many attempts have been conducted to improve its NUE. In the present study, effect of micro- and macro-nutrient addition on performance of tilapia-pak choi aquaponics was investigated. Results showed that the addition of micro- and macro-nutrients improved the growth of plant directly and facilitated fish physiology indirectly, which subsequently increased NUE of aquaponics from 40.42 to 50.64%. In addition, remarkable lower total phosphorus concentration was obtained in aquaponics with micro- and macro-nutrient addition, which was attributed to the formation of struvite. Most of the added micro-nutrients were enriched in plant root, while macro-nutrients mainly existed in water. Moreover, no enrichment of micro- and macro-nutrients in aquaponic products (i.e., fish and plant leaves) was observed, indicating that it had no influence on food safety. The findings here reported manifest that appropriate addition of micro- and macro-nutrients to aquaponics is necessary, and would improve its economic feasibility.

Effect of Hypoeutectic Boron Additions on the Grain Size and Mechanical Properties of Ti-6Al-4V Manufactured with Powder Bed Electron Beam Additive Manufacturing

Science.gov (United States)

Mahbooba, Zaynab; West, Harvey; Harrysson, Ola; Wojcieszynski, Andrzej; Dehoff, Ryan; Nandwana, Peeyush; Horn, Timothy

2017-03-01

In additive manufacturing, microstructural control is feasible via processing parameter alteration. However, the window for parameter variation for certain materials, such as Ti-6Al-4V, is limited, and alternative methods must be employed to customize microstructures. Grain refinement and homogenization in cast titanium alloys has been demonstrated through the addition of hypoeutectic concentrations of boron. This work explores the influence of 0.00 wt.%, 0.25 wt.%, 0.50 wt.%, and 1.0 wt.% boron additions on the microstructure and bulk mechanical properties of Ti-6Al-4V samples fabricated in an Arcam A2 electron beam melting (EBM) system with commercial processing parameters for Ti-6Al-4V. Analyses of EBM fabricated Ti-6Al-4V + B indicate that the addition of 0.25-1.0 wt.% boron progressively refines the grain structure, and it improves hardness and elastic modulus. Despite a reduction in size, the β grain structure remained columnar as a result of directional heat transfer during EBM fabrication.

Laboratory directed research and development 2006 annual report.

Energy Technology Data Exchange (ETDEWEB)

Westrich, Henry Roger

2007-03-01

This report summarizes progress from the Laboratory Directed Research and Development (LDRD) program during fiscal year 2006. In addition to a programmatic and financial overview, the report includes progress reports from 430 individual R&D projects in 17 categories.

Divergent Total Syntheses of (-)-Huperzine Q, (+)-Lycopladine B, (+)-Lycopladine C, and (-)-4-epi-Lycopladine D.

Science.gov (United States)

Hong, Benke; Hu, Dachao; Wu, Jinbao; Zhang, Jing; Li, Houhua; Pan, Yingming; Lei, Xiaoguang

2017-07-04

We report herein our synthetic efforts towards the divergent syntheses of (-)-huperzine Q (1), (+)-lycopladine B (2), (+)-lycopladine C (3), and (-)-lycopladine D (4). The 10-step total synthesis of (-)-huperzine Q (1) and the first total syntheses of (+)-lycopladines B (2) and C (3) were accomplished through a series of cascade reactions. Our approach involved a Michael addition/aldol/intramolecular C-alkylation sequence to forge the 6/9 spirocycle ring, and this was followed by an ethylene-accelerated carbonyl-olefin metathesis to construct the common 6/5/9 ring system. Finally, late-stage enamine bromofunctionalization enabled us to access (-)-huperzine Q (1), (+)-lycopladine B (2), and (+)-lycopladine C (3), and a tandem C4-epimerization/retro-Claisen condensation furnished (-)-4-epi-lycopladine D (63). © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Laboratory-directed research and development

International Nuclear Information System (INIS)

Gerstl, S.A.W.; Caughran, A.B.

1992-05-01

This report summarizes progress from the Laboratory-Directed Research and Development (LDRD) program during fiscal year 1991. In addition to a programmatic and financial overview, the report includes progress reports from 230 individual R ampersand D projects in 9 scientific categories: atomic and molecular physics; biosciences; chemistry; engineering and base technologies; geosciences; space sciences, and astrophysics; materials sciences; mathematics and computational sciences; nuclear and particle physics; and plasmas, fluids, and particle beams

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.

1994-03-01

This report presents the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1993. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1993-03-01

This report present the results of the NRC Direct Radiation Monitoring Network for the fourth quarter of 1992. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program

Direction selectivity in the larval zebrafish tectum is mediated by asymmetric inhibition

Directory of Open Access Journals (Sweden)

Abhinav eGrama

2012-09-01

Full Text Available The extraction of the direction of motion is an important computation performed by many sensory systems and in particular, the mechanism by which direction selective ganglion cells (DS-RGCs in the retina acquire their selective properties, has been studied extensively. However, whether DS-RGCs simply relay this information to downstream areas or whether additional and potentially de-novo processing occurs in these recipient structures is a matter of great interest. Neurons in the larval zebrafish tectum, the largest retino-recipent area in this animal, show direction selective responses to moving visual stimuli but how these properties are acquired is still unknown. In order to study this, we first used two-photon calcium imaging to classify the population responses of tectal cells to bars moving at different speeds and in different directions. Subsequently, we performed in-vivo whole cell electrophysiology on these direction selective tectal neurons and we found that their inhibitory inputs were strongly biased towards the null direction of motion, whereas the excitatory inputs showed little selectivity. In addition, we found that excitatory currents evoked by a stimulus moving in the preferred direction occurred before the inhibitory currents whereas a stimulus moving in the null direction evoked currents in the reverse temporal order. The membrane potential modulations resulting from these currents were enhanced by the spike generation mechanism to generate amplified direction selectivity in the spike output. Thus our results implicate a local inhibitory circuit in generating direction selectivity in tectal neurons.

Additive Manufacturing of Biomedical Constructs with Biomimetic Structural Organizations.

Science.gov (United States)

Li, Xiao; He, Jiankang; Zhang, Weijie; Jiang, Nan; Li, Dichen

2016-11-09

Additive manufacturing (AM), sometimes called three-dimensional (3D) printing, has attracted a lot of research interest and is presenting unprecedented opportunities in biomedical fields, because this technology enables the fabrication of biomedical constructs with great freedom and in high precision. An important strategy in AM of biomedical constructs is to mimic the structural organizations of natural biological organisms. This can be done by directly depositing cells and biomaterials, depositing biomaterial structures before seeding cells, or fabricating molds before casting biomaterials and cells. This review organizes the research advances of AM-based biomimetic biomedical constructs into three major directions: 3D constructs that mimic tubular and branched networks of vasculatures; 3D constructs that contains gradient interfaces between different tissues; and 3D constructs that have different cells positioned to create multicellular systems. Other recent advances are also highlighted, regarding the applications of AM for organs-on-chips, AM-based micro/nanostructures, and functional nanomaterials. Under this theme, multiple aspects of AM including imaging/characterization, material selection, design, and printing techniques are discussed. The outlook at the end of this review points out several possible research directions for the future.

NRC TLD Direct Radiation Monitoring Network

International Nuclear Information System (INIS)

Struckmeyer, R.; McNamara, N.

1991-04-01

This report presents the results of the NRC [Nuclear Regulatory Commission] Direct Radiation Monitoring Network for the fourth quarter of 1990. It provides the ambient radiation levels measured in the vicinity of 75 sites throughout the United States. In addition, it describes the equipment used, monitoring station selection criteria, characterization of the dosimeter response, calibration procedures, statistical methods, intercomparison, and quality assurance program. 3 figs., 4 tabs

Laser assisted hybrid additive manufacturing of thermoelectric modules

Science.gov (United States)

Zhang, Tao; Tewolde, Mahder; Longtin, Jon P.; Hwang, David J.

2017-02-01

Thermoelectric generators (TEGs) are an attractive means to produce electricity, particular from waste heat applications. However, TEGs are almost exclusively manufactured as flat, rigid modules of limited size and shape, and therefore an appropriate mounting for intimate contact of TEGs modules onto arbitrary surfaces represents a significant challenge. In this study, we introduce laser assisted additive manufacturing method to produce multi-layered thermoelectric generator device directly on flat and non-flat surfaces for waste heat recovery. The laser assisted processing spans from laser scribing of thermal sprayed thin films, curing of dispensed thermoelectric inks and selective laser sintering to functionalize thermoelectric materials.

Nonparametric additive regression for repeatedly measured data

KAUST Repository

Carroll, R. J.

2009-05-20

We develop an easily computed smooth backfitting algorithm for additive model fitting in repeated measures problems. Our methodology easily copes with various settings, such as when some covariates are the same over repeated response measurements. We allow for a working covariance matrix for the regression errors, showing that our method is most efficient when the correct covariance matrix is used. The component functions achieve the known asymptotic variance lower bound for the scalar argument case. Smooth backfitting also leads directly to design-independent biases in the local linear case. Simulations show our estimator has smaller variance than the usual kernel estimator. This is also illustrated by an example from nutritional epidemiology. © 2009 Biometrika Trust.

Theory of direct interparticle action

International Nuclear Information System (INIS)

Vladimirov, Yu.S.; Turygin, A.Yu.

1986-01-01

Unusual point of view on the physical picture of the Universe and ratio between main physical categories is considered. Principal moments and theory peculiarities based on the conception of direct interparticle action are underlined. The direct interparticle action theory (DIAT) is considered from the position of choosing one or another axiomatics. At first the Fokker action principle is postulated there and then identical satisfiability of field equations is proved. All that relates to vacuum DIAT ignores and actions of matter formations are used as the basis. DIAT bears up against a global factor-account of absrbers of all surroundings (the Mach principle). The DIAT pretended to relativistic description of only additional concepts with the previously asigned space-time ratios. Concept for construction of the physical picture of the Universe, where classical space-time ratios being of secondary character, is suggested

Mechanistic Study of Electrolyte Additives to Stabilize High-Voltage Cathode–Electrolyte Interface in Lithium-Ion Batteries

Energy Technology Data Exchange (ETDEWEB)

Gao, Han [Chemical; Maglia, Filippo [BMW Group, Munich 80788, Germany; Lamp, Peter [BMW Group, Munich 80788, Germany; Amine, Khalil [Chemical; Chen, Zonghai [Chemical

2017-12-13

Current developments of electrolyte additives to stabilize electrode-electrolyte interface in Li-ion batteries highly rely on a trial-and-error search, which involves repetitive testing and intensive amount of resources. The lack of understandings on the fundamental protection mechanisms of the additives significantly increases the difficulty for the transformational development of new additives. In this study, we investigated two types of individual protection routes to build a robust cathode-electrolyte interphase at high potentials: (i) a direct reduction in the catalytic decomposition of the electrolyte solvent; and (ii) formation of a “corrosion inhibitor film” that prevents severely attack and passivation from protons that generated from the solvent oxidation, even the decomposition of solvent cannot not mitigated. Effect of three exemplary electrolyte additives: (i) lithium difluoro(oxalato)borate (LiDFOB); (ii) 3-hexylthiophene (3HT); and (iii) tris(hexafluoro-iso-propyl)phosphate (HFiP), on LiNi0.6Mn0.2Co0.2O2 (NMC 622) cathode were investigated to validate our hypothesis. It is demonstrated that understandings of both electrolyte additives and solvent are essential and careful balance between the cathode protection mechanism of additives and their side effects is critical to obtain optimum results. More importantly, this study opens up new directions of rational design of functional electrolyte additives for the next generation high-energy density lithium-ion chemistries.

Biocompatibility of hydroxyapatite scaffolds processed by lithography-based additive manufacturing.

Science.gov (United States)

Tesavibul, Passakorn; Chantaweroad, Surapol; Laohaprapanon, Apinya; Channasanon, Somruethai; Uppanan, Paweena; Tanodekaew, Siriporn; Chalermkarnnon, Prasert; Sitthiseripratip, Kriskrai

2015-01-01

The fabrication of hydroxyapatite scaffolds for bone tissue engineering applications by using lithography-based additive manufacturing techniques has been introduced due to the abilities to control porous structures with suitable resolutions. In this research, the use of hydroxyapatite cellular structures, which are processed by lithography-based additive manufacturing machine, as a bone tissue engineering scaffold was investigated. The utilization of digital light processing system for additive manufacturing machine in laboratory scale was performed in order to fabricate the hydroxyapatite scaffold, of which biocompatibilities were eventually evaluated by direct contact and cell-culturing tests. In addition, the density and compressive strength of the scaffolds were also characterized. The results show that the hydroxyapatite scaffold at 77% of porosity with 91% of theoretical density and 0.36 MPa of the compressive strength are able to be processed. In comparison with a conventionally sintered hydroxyapatite, the scaffold did not present any cytotoxic signs while the viability of cells at 95.1% was reported. After 14 days of cell-culturing tests, the scaffold was able to be attached by pre-osteoblasts (MC3T3-E1) leading to cell proliferation and differentiation. The hydroxyapatite scaffold for bone tissue engineering was able to be processed by the lithography-based additive manufacturing machine while the biocompatibilities were also confirmed.

Direct methods in protein crystallography.

Science.gov (United States)

Karle, J

1989-11-01

It is pointed out that the 'direct methods' of phase determination for small-structure crystallography do not have immediate applicability to macromolecular structures. The term 'direct methods in macromolecular crystallography' is suggested to categorize a spectrum of approaches to macromolecular structure determination in which the analyses are characterized by the use of two-phase and higher-order-phase invariants. The evaluation of the invariants is generally obtained by the use of heavy-atom techniques. The results of a number of the more recent algebraic and probabilistic studies involving isomorphous replacement and anomalous dispersion thus become valid subjects for discussion here. These studies are described and suggestions are also presented concerning future applicability. Additional discussion concerns the special techniques of filtering, the use of non-crystallographic symmetry, some features of maximum entropy and attempts to apply phase-determining formulas to the refinement of macromolecular structure. It is noted that, in addition to the continuing remarkable progress in macromolecular crystallography based on the traditional applications of isomorphous replacement and anomalous dispersion, recent valuable advances have been made in the application of non-crystallographic symmetry, in particular, to virus structures and in applications of filtering. Good progress has also been reported in the application of exact linear algebra to multiple-wavelength anomalous-dispersion investigations of structures containing anomalous scatterers of only moderate scattering power.

Toward (-)-Enterocin: An Improved Cuprate Barbier Protocol To Overcome Strain and Sterical Hindrance.

Science.gov (United States)

Rizzo, Antonio; Trauner, Dirk

2018-04-06

An approach toward (-)-enterocin, an antibiotic isolated from Streptomyces hygroscopicus, is described. Its compact, heavily oxidized protoadamantane core represents a daunting challenge for an efficient synthesis. Convergent assembly of its 2-oxabicyclo[3.3.1]nonane core with a cuprate-mediated Barbier reaction is disclosed. Its functionalization to a suitable substrate for a biomimetic aldol to close the final ring of the natural product is evaluated.

Two new labdane diterpenes from fresh leaves of Leonurus japonicus and their degradation during drying.

Science.gov (United States)

Fuchino, Hiroyuki; Daikonya, Akihiro; Kumagai, Takeo; Goda, Yukihiro; Takahashi, Yutaka; Kawahara, Nobuo

2013-01-01

Degradation of the components of Leonurus Herb was examined during drying. Compounds 1 and 2 were detected on TLC at lower temperature, but not at higher temperature. Their chemical structures were determined by spectral methods. They immediately decomposed even at 40°C in chloroform solution. They are believed to be transformed through a retro-aldol reaction. Compounds 1 and 2 have not been previously reported.

Biological and structure-activity evaluation of chalcone derivatives against bacteria and fungi

Energy Technology Data Exchange (ETDEWEB)

Silva, Wender A.; Andrade, Carlos Kleber Z.; Napolitano, Hamilton B., E-mail: wender@unb.br, E-mail: ckleber@unb.br [Universidade de Brasilia (LaQMOS/UnB), DF (Brazil). Inst. de Quimica; Vencato, Ivo; Castro, Miriam R.C. de; Camargo, Ademir J. [Universidade Estadual de Goias (UEG), Anapolis, GO (Brazil). Ciencias Exatas e Tecnologicas; Lariucci, Carlito [Universidade Estadual de Goias (UEG), Goiania, GO (Brazil). Inst. de Fisica

2013-01-15

The present work describes the antibacterial and antifungal activities of several chalcones obtained by a straight Claisen-Schmidt aldol condensation determined by the minimal inhibitory concentration against different microorganisms (Gram-positive and Gram-negative bacteria and fungi). Solid state crystal structures of seven chalcones were determined by X-ray diffraction (XRD) analysis. Chemometric studies were carried out in order to identify a potential structure activity relationship. (author)

A facile approach for the synthesis of C13-C24 fragments of maltepolides A, C and D.

Science.gov (United States)

Rao, P Sankara; Srihari, P

2016-10-12

A linear, chiron approach for the synthesis of C13-C24 fragments of cytostatic maltepolides A, C and D consisting of a tetrahydrofuran subunit and a chiral alkenyl/alkyl substituent is achieved from (+)-diethyl l-tartrate. The other chiral stereocenters were generated by employing key reactions such as Crimmins aldol, alkynylation and CeCl 3 ·7H 2 O mediated Luche reduction reactions.

Synthesis of jet fuel range branched cycloalkanes with mesityl oxide and 2-methylfuran from lignocellulose

Science.gov (United States)

Li, Shanshan; Li, Ning; Wang, Wentao; Li, Lin; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2016-09-01

Jet fuel range branched cycloalkanes with high density (0.82 g mL-1) and low freezing point (217-219 K) was first prepared by the solvent-free intramolecular aldol condensation of the trione from the hydrolysis of the alkylation product of mesityl oxide and 2-methylfuran (or the one-pot reaction of mesityl oxide, 2-methylfuran and water), followed by hydrodeoxygenation (HDO).

Solvent-free synthesis of C10 and C11 branched alkanes from furfural and methyl isobutyl ketone.

Science.gov (United States)

Yang, Jinfan; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Wang, Xiaodong; Cong, Yu; Zhang, Tao

2013-07-01

Our best results jet: C10 and C11 branched alkanes, with low freezing points, are synthesized through the aldol condensation of furfural and methyl isobutyl ketone from lignocellulose, which is then followed by hydrodeoxygenation. These jet-fuel-range alkanes are obtained in high overall yields (≈90%) under solvent-free conditions. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Estimating the impact of structural directionality: How reliable are undirected connectomes?

Directory of Open Access Journals (Sweden)

Penelope Kale

2018-06-01

Full Text Available Directionality is a fundamental feature of network connections. Most structural brain networks are intrinsically directed because of the nature of chemical synapses, which comprise most neuronal connections. Because of the limitations of noninvasive imaging techniques, the directionality of connections between structurally connected regions of the human brain cannot be confirmed. Hence, connections are represented as undirected, and it is still unknown how this lack of directionality affects brain network topology. Using six directed brain networks from different species and parcellations (cat, mouse, C. elegans, and three macaque networks, we estimate the inaccuracies in network measures (degree, betweenness, clustering coefficient, path length, global efficiency, participation index, and small-worldness associated with the removal of the directionality of connections. We employ three different methods to render directed brain networks undirected: (a remove unidirectional connections, (b add reciprocal connections, and (c combine equal numbers of removed and added unidirectional connections. We quantify the extent of inaccuracy in network measures introduced through neglecting connection directionality for individual nodes and across the network. We find that the coarse division between core and peripheral nodes remains accurate for undirected networks. However, hub nodes differ considerably when directionality is neglected. Comparing the different methods to generate undirected networks from directed ones, we generally find that the addition of reciprocal connections (false positives causes larger errors in graph-theoretic measures than the removal of the same number of directed connections (false negatives. These findings suggest that directionality plays an essential role in shaping brain networks and highlight some limitations of undirected connectomes. Most brain networks are inherently directed because of the nature of chemical synapses

THE DIRECTIVE SPEECH ACTS USED IN ENGLISH SPEAKING CLASS

Directory of Open Access Journals (Sweden)

Muhammad Khatib Bayanuddin

2016-12-01

Full Text Available This research discusses about an analysis of the directive speech acts used in english speaking class at the third semester of english speaking class of english study program of IAIN STS Jambi. The aims of this research are to describe the types of directive speech acts and politeness strategies that found in English speaking class. This research used descriptive qualitative method. This method used to describe clearly about the types and politeness strategies of directive speech acts based on the data in English speaking class. The result showed that in English speaking class that there are some types and politeness strategies of directive speech acts, such as: requestives, questions, requirements, prohibitives, permissives, and advisores as types, as well as on-record indirect strategies (prediction statement, strong obligation statement, possibility statement, weaker obligation statement, volitional statement, direct strategies (imperative, performative, and nonsentential strategies as politeness strategies. The achievement of this research are hoped can be additional knowledge about linguistics study, especially in directive speech acts and can be developed for future researches. Key words: directive speech acts, types, politeness strategies.

Food additives used in meat processing according to the Polish and European Union legislation.

Science.gov (United States)

Uradziński, J; Weiner, M

2003-01-01

This paper presents the legal regulations related to the use of food additives in meat production in Poland and the European Union. The Polish legal definition of food additives is given as well as the classification of permitted food additives added to food and stimulants by their technological function. In addition, a definition of processing aids in the food industry is included. It shows that Polish legislation includes food additives used to ensure or improve food nutritional value, whereas in the EU legislation, these substances are not included in the list of food additives. Moreover, the Council Directives include food additive specific purity criteria, whereas the Polish regulations do not mention the legal regulations of this issue in practice. The European Union use mechanisms and procedures for the introduction of new food additives into internal markets as well as controlling the circulation of additives. The Polish legislation in practice, however, does not determine approval or methods for the introduction of new food additives to the market. Legal regulations on the monitoring of food additives no exist.

Synthesis of organolanthanides by metal addition on insaturated substrates in ether and reactivity

International Nuclear Information System (INIS)

Olivier, H.

1988-01-01

The aim of the study is the extension to rare earths of the synthesis, well known for alkaline or alkaline earth metals, by direct metal addition to insaturated substrates in ether and where the metal is directly bound to carbon. A definition of formation conditions and affinity rules is attempled, both with substrates (essentially aromatic hydrocarbons and ketones) and with metals: Yb, Sm, Ce, Nd and others. The nature of obtained products by reaction of electrophiles on synthetised organometallics, allows investigations specific reactivity and structure. Potential catalytic transformation of olefins is precised [fr

Additive manufacturing: Characterization of TI-6AI-4V alloy intended for biomedical application

CSIR Research Space (South Africa)

Ramosoeu, ME

2010-10-01

Full Text Available Direct Metal Laser Sintering (DMLS) is one of the new Laser Additive Manufacturing (LAM) techniques used for producing complex topology components mostly found in medical applications. The work presented in this paper focuses on metallographic...

Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

Science.gov (United States)

Law, S L; Newman, J H; Ptak, F L

1990-02-01

A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

Activated carbon addition affects substrate pH and germination of six plant species

NARCIS (Netherlands)

Kabouw, P.; Nab, M.; Dam, van M.

2010-01-01

Activated carbon (AC) is widely used in ecological studies for neutralizing allelopathic compounds. However, it has been suggested that AC has direct effects on plants because it alters substrate parameters such as nutrient availability and pH. These side-effects of AC addition may interfere with

Activated carbon addition affects soil pH and germination of six plant species

NARCIS (Netherlands)

Kabouw, P.; Nab, M.R.; Van Dam, N.M.

2010-01-01

Activated carbon (AC) is widely used in ecological studies for neutralizing allelopathic compounds. However, it has been suggested that AC has direct effects on plants because it alters substrate parameters such as nutrient availability and pH. These side-effects of AC addition may interfere with

Additive manufacturing of titanium alloys state of the art, challenges and opportunities

CERN Document Server

Dutta, Bhaskar

2016-01-01

Additive Manufacturing of Titanium Alloys: State of the Art, Challenges and Opportunities provides alternative methods to the conventional approach for the fabrication of the majority of titanium components produced via the cast and wrought technique, a process which involves a considerable amount of expensive machining. In contrast, the Additive Manufacturing (AM) approach allows very close to final part configuration to be directly fabricated minimizing machining cost, while achieving mechanical properties at least at cast and wrought levels. In addition, the book offers the benefit of significant savings through better material utilization for parts with high buy-to-fly ratios (ratio of initial stock mass to final part mass before and after manufacturing). As titanium additive manufacturing has attracted considerable attention from both academicians and technologists, and has already led to many applications in aerospace and terrestrial systems, as well as in the medical industry, this book explores the un...

Fatigue performance of additively manufactured meta-biomaterials : The effects of topology and material type

NARCIS (Netherlands)

Ahmadi, S.M.; Hedayati, R.; Li, Y; Lietaert, K.; Tümer, N.; Fatemi, A.; Rans, C.D.; Pouran, B.; Weinans, H.H.; Zadpoor, A.A.

2018-01-01

Additive manufacturing (AM) techniques enable fabrication of bone-mimicking meta-biomaterials with unprecedented combinations of topological, mechanical, and mass transport properties. The mechanical performance of AM meta-biomaterials is a direct function of their topological design. It is,

Evaluation of polymer micro parts produced by additive manufacturing processes using vat photopolymerization method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

2017-01-01

Micro manufacturing scale feature production by Additive Manufacturing (AM) processes for the direct production of miniaturized polymer components is analysed in this work. The study characterizes the AM processes for polymer micro parts productions using the vat photopolymerization method...

Self-Cleaning Photocatalytic Polyurethane Coatings Containing Modified C60 Fullerene Additives

Directory of Open Access Journals (Sweden)

Jeffrey G. Lundin

2014-08-01

Full Text Available Surfaces are often coated with paint for improved aesthetics and protection; however, additional functionalities that impart continuous self-decontaminating and self-cleaning properties would be extremely advantageous. In this report, photochemical additives based on C60 fullerene were incorporated into polyurethane coatings to investigate their coating compatibility and ability to impart chemical decontaminating capability to the coating surface. C60 exhibits unique photophysical properties, including the capability to generate singlet oxygen upon exposure to visible light; however, C60 fullerene exhibits poor solubility in solvents commonly employed in coating applications. A modified C60 containing a hydrophilic moiety was synthesized to improve polyurethane compatibility and facilitate segregation to the polymer–air interface. Bulk properties of the polyurethane films were analyzed to investigate additive–coating compatibility. Coatings containing photoactive additives were subjected to self-decontamination challenges against representative chemical contaminants and the effects of additive loading concentration, light exposure, and time on chemical decontamination are reported. Covalent attachment of an ethylene glycol tail to C60 improved its solubility and dispersion in a hydrophobic polyurethane matrix. Decomposition products resulting from oxidation were observed in addition to a direct correlation between additive loading concentration and decomposition of surface-residing contaminants. The degradation pathways deduced from contaminant challenge byproduct analyses are detailed.

The development of catalytic nucleophilic additions of terminal alkynes in water.

Science.gov (United States)

Li, Chao-Jun

2010-04-20

One of the major research endeavors in synthetic chemistry over the past two decades is the exploration of synthetic methods that work under ambient atmosphere with benign solvents, that maximize atom utilization, and that directly transform natural resources, such as renewable biomass, from their native states into useful chemical products, thus avoiding the need for protecting groups. The nucleophilic addition of terminal alkynes to various unsaturated electrophiles is a classical (textbook) reaction in organic chemistry, allowing the formation of a C-C bond while simultaneously introducing the alkyne functionality. A prerequisite of this classical reaction is the stoichiometric generation of highly reactive metal acetylides. Over the past decade, our laboratory and others have been exploring an alternative, the catalytic and direct nucleophilic addition of terminal alkynes to unsaturated electrophiles in water. We found that various terminal alkynes can react efficiently with a wide range of such electrophiles in water (or organic solvent) in the presence of simple and readily available catalysts, such as copper, silver, gold, iron, palladium, and others. In this Account, we describe the development of these synthetic methods, focusing primarily on results from our laboratory. Our studies include the following: (i) catalytic reaction of terminal alkynes with acid chloride, (ii) catalytic addition of terminal alkynes to aldehydes and ketones, (iii) catalytic addition of alkynes to C=N bonds, and (iv) catalytic conjugate additions. Most importantly, these reactions can tolerate various functional groups and, in many cases, perform better in water than in organic solvents, clearly defying classical reactivities predicated on the relative acidities of water, alcohols, and terminal alkynes. We further discuss multicomponent and enantioselective reactions that were developed. These methods provide an alternative to the traditional requirement of separate steps in

Boosting the Performance of Ionic-Liquid-Based Supercapacitors with Polar Additives

Energy Technology Data Exchange (ETDEWEB)

Liu, Kun [Univ. of California, Riverside, CA (United States). Dept. of Chemical and Environmental Engineering; Wu, Jianzhong [Univ. of California, Riverside, CA (United States). Dept. of Chemical and Environmental Engineering

2016-10-05

Recent years have witnessed growing interests in both the fundamentals and applications of electric double layer capacitors (EDLCs), also known as supercapacitors. A number of strategies have been explored to optimize the device performance in terms of both the energy and power densities. Because the properties of electric double layers (EDL) are sensitive to ion distributions in the close vicinity of the electrode surfaces, the supercapacitor performance is sensitive to both the electrode pore structure and the electrolyte composition. In this paper, we study the effects of polar additives on EDLC capacitance using the classical density functional theory within the framework of a coarse-grained model for the microscopic structure of the porous electrodes and room-temperature ionic liquids. The theoretical results indicate that a highly polar, low-molecular-weight additive is able to drastically increase the EDLC capacitance at low bulk concentration. Additionally, the additive is able to dampen the oscillatory dependence of the capacitance on the pore size, thereby boosting the performance of amorphous electrode materials. Finally, the theoretical predictions are directly testable with experiments and provide new insights into the additive effects on EDL properties.

Prebiotic synthesis of 2-deoxy-d-ribose from interstellar building blocks promoted by amino esters or amino nitriles.

Science.gov (United States)

Steer, Andrew M; Bia, Nicolas; Smith, David K; Clarke, Paul A

2017-09-25

Understanding the prebiotic genesis of 2-deoxy-d-ribose, which forms the backbone of DNA, is of crucial importance to unravelling the origins of life, yet remains open to debate. Here we demonstrate that 20 mol% of proteinogenic amino esters promote the selective formation of 2-deoxy-d-ribose over 2-deoxy-d-threopentose in combined yields of ≥4%. We also demonstrate the first aldol reaction promoted by prebiotically-relevant proteinogenic amino nitriles (20 mol%) for the enantioselective synthesis of d-glyceraldehyde with 6% ee, and its subsequent conversion into 2-deoxy-d-ribose in yields of ≥ 5%. Finally, we explore the combination of these two steps in a one-pot process using 20 mol% of an amino ester or amino nitrile promoter. It is hence demonstrated that three interstellar starting materials, when mixed together with an appropriate promoter, can directly lead to the formation of a mixture of higher carbohydrates, including 2-deoxy-d-ribose.

Use of direct marketing in nonprofit organizations

Directory of Open Access Journals (Sweden)

Popović Ana

2010-01-01

Full Text Available Non profit organizations represent very heterogenus group of organizations which can be determined by the fact that they are being used as forums for creation and distribution of new ideas. Their aim is to raise public awareness on the purpose they promote and get the reply for their initiatives for gaining support in form of monetary sources for charities, vote for political candidate or achieving a communicational goal. Non governmental organizations, as the dominant form of non profit organizations, are being founded with mission to raise public awareness on some issue or provide help to certain marginalized group. The direct marketing instruments and techniques are considered to be very useful for achieving mission formulated that way. They are, by their nature, precisely targeted and objective-oriented and require direct reply. Apart from that, direct marketing activities are cost-efficient, costs that they generate can be shown in financial reports, and results of undertaken initiatives are directly measurable. All the mentioned lead to conclusion that direct marketing is, for additional reasons, even more appropriate for NPOs having in mind that they usually have limited available resources. In the relevant literature two main roles of direct marketing in non profit organizations are mentioned - managing relations with representatives of stakeholder groups and fundraising. In this paper, therefore, after the facts referring functioning of NPOs, direct marketing strategies used for mentioned purposes will be presented consequently.

The ADR Directive: designed to fail? A hole-ridden stairway to consumer justice

NARCIS (Netherlands)

Luzak, J.

2016-01-01

The European legislator adopted the new Alternative Dispute Resolution (ADR) Directive with an aim to create an additional, attractive stairway to consumer justice. As such, the ADR Directive intends to encourage more consumers to invoke their consumer rights and thus strengthen consumer law

Brown spider dermonecrotic toxin directly induces nephrotoxicity

International Nuclear Information System (INIS)

Chaim, Olga Meiri; Sade, Youssef Bacila; Bertoni da Silveira, Rafael; Toma, Leny; Kalapothakis, Evanguedes; Chavez-Olortegui, Carlos; Mangili, Oldemir Carlos; Gremski, Waldemiro; Dietrich, Carl Peter von; Nader, Helena B.; Sanches Veiga, Silvio

2006-01-01

Brown spider (Loxosceles genus) venom can induce dermonecrotic lesions at the bite site and systemic manifestations including fever, vomiting, convulsions, disseminated intravascular coagulation, hemolytic anemia and acute renal failure. The venom is composed of a mixture of proteins with several molecules biochemically and biologically well characterized. The mechanism by which the venom induces renal damage is unknown. By using mice exposed to Loxosceles intermedia recombinant dermonecrotic toxin (LiRecDT), we showed direct induction of renal injuries. Microscopic analysis of renal biopsies from dermonecrotic toxin-treated mice showed histological alterations including glomerular edema and tubular necrosis. Hyalinization of tubules with deposition of proteinaceous material in the tubule lumen, tubule epithelial cell vacuoles, tubular edema and epithelial cell lysis was also observed. Leukocytic infiltration was neither observed in the glomerulus nor the tubules. Renal vessels showed no sign of inflammatory response. Additionally, biochemical analyses showed such toxin-induced changes in renal function as urine alkalinization, hematuria and azotemia with elevation of blood urea nitrogen levels. Immunofluorescence with dermonecrotic toxin antibodies and confocal microscopy analysis showed deposition and direct binding of this toxin to renal intrinsic structures. By immunoblotting with a hyperimmune dermonecrotic toxin antiserum on renal lysates from toxin-treated mice, we detected a positive signal at the region of 33-35 kDa, which strengthens the idea that renal failure is directly induced by dermonecrotic toxin. Immunofluorescence reaction with dermonecrotic toxin antibodies revealed deposition and binding of this toxin directly in MDCK epithelial cells in culture. Similarly, dermonecrotic toxin treatment caused morphological alterations of MDCK cells including cytoplasmic vacuoles, blebs, evoked impaired spreading and detached cells from each other and from

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

Science.gov (United States)

O’Neal, T. Derek

2016-01-01

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

Directional sound radiation from substation transformers

International Nuclear Information System (INIS)

Maybee, N.

2009-01-01

This paper presented the results of a study in which acoustical measurements at two substations were analyzed to investigate the directional behaviour of typical arrays having 2 or 3 transformers. Substation transformers produce a characteristic humming sound that is caused primarily by vibration of the core at twice the frequency of the power supply. The humming noise radiates predominantly from the tank enclosing the core. The main components of the sound are harmonics of 120 Hz. Sound pressure level data were obtained for various directions and distances from the arrays, ranging from 0.5 m to over 100 m. The measured sound pressure levels of the transformer tones displayed substantial positive and negative excursions from the calculated average values for many distances and directions. The results support the concept that the directional effects are associated with constructive and destructive interference of tonal sound waves emanating from different parts of the array. Significant variations in the directional sound pattern can occur in the near field of a single transformer or an array, and the extent of the near field is significantly larger than the scale of the array. Based on typical dimensions for substation sites, the distance to the far field may be much beyond the substation boundary and beyond typical setbacks to the closest dwellings. As such, the directional sound radiation produced by transformer arrays introduces additional uncertainty in the prediction of substation sound levels at dwellings within a few hundred meters of a substation site. 4 refs., 4 figs.

Direct assay for urine cortisol with cortisol kit TFB

Energy Technology Data Exchange (ETDEWEB)

Manaka, Yukiko; Watanabe, Michiko; Hosoya, Takaaki [Yamagata Univ. (Japan). Hospital

2002-05-01

We examined Cortisol Kit TFB for direct assay of urine cortisol. And the multiplication by dilution factor of urine cortisol values in this kit was examined. The coefficient of correlation of cortisol levels (46 urine samples) between Cortisol Kit TFB and Chemilumi ACS-Cortisol II, which is another kit for direct assay of urine cortisol, was r=0.858, y=1.86x+38.2 (p<0.001). There were differences between the both cortisol levels of each urine sample in spite of the good coefficient of correlation. The urine cortisol values obtained from the standard curve in addition of 50 {mu}l of zero standard were 50-80% of the values obtained from the standard curve in the package insert. These results suggest that the specificity of the antibodies of both direct assay kits for urine cortisol may be different each other, and the multiplication by 1.09, the dilution factor due to the addition of zero standard to only urine sample, is unnecessary although it is indispensable for urine samples to add zero standard. Cortisol Kit TFB was very convenient for its easy assay procedure and short incubation. (author)

Direct assay for urine cortisol with cortisol kit TFB

International Nuclear Information System (INIS)

Manaka, Yukiko; Watanabe, Michiko; Hosoya, Takaaki

2002-01-01

We examined Cortisol Kit TFB for direct assay of urine cortisol. And the multiplication by dilution factor of urine cortisol values in this kit was examined. The coefficient of correlation of cortisol levels (46 urine samples) between Cortisol Kit TFB and Chemilumi ACS-Cortisol II, which is another kit for direct assay of urine cortisol, was r=0.858, y=1.86x+38.2 (p<0.001). There were differences between the both cortisol levels of each urine sample in spite of the good coefficient of correlation. The urine cortisol values obtained from the standard curve in addition of 50 μl of zero standard were 50-80% of the values obtained from the standard curve in the package insert. These results suggest that the specificity of the antibodies of both direct assay kits for urine cortisol may be different each other, and the multiplication by 1.09, the dilution factor due to the addition of zero standard to only urine sample, is unnecessary although it is indispensable for urine samples to add zero standard. Cortisol Kit TFB was very convenient for its easy assay procedure and short incubation. (author)

Agricultural insurance under the Solvency II Directive

Directory of Open Access Journals (Sweden)

Njegomir Vladimir

2014-01-01

Full Text Available Solvency II Directive represents a new framework of unique solvency regulation of insurance and reinsurance companies in the European Union. Although it has not yet been implemented in national legislations, it can be concluded, based on the directive wording and conducted quantitative studies, that it will have implications on agricultural producers since they are the users of insurance services. The aim of the research presented in this paper is to analyse the implications of the new directive to agricultural producers since they are the insureds and the main actors of agribusiness. Firstly, the paper gives an overview of the basic features of the new regulatory framework and then it points at the issues and the needs for intensive application of Directive in order to improve the insurance business in Serbia. The process will direct the settlement of major claims, the ones that are typical of catastrophic risks in agriculture, towards the insurance, while the expectations from the government will be directed towards the regulation of the setting and economic measures (development and investment subsidies, cooperative movement. In addition, the paper points at the demands of the new regulation and analyses the implications of the new regulation regarding the settlement of claims resulting from major flood since it represents the example that proves the basic postulate.

Understanding the role of marketing communications in direct marketing

NARCIS (Netherlands)

P. Naik; N. Piersma (Nanda)

2002-01-01

textabstractThe standard RFM models used by direct marketers include behavioral variables, but ignore the role of marketing communications. In addition, RFM models allow customer responsiveness to vary across different customers, but not across diiferent time periods. Hence, the authors first

Concentrated energy addition for active drag reduction in hypersonic flow regime

Science.gov (United States)

Ashwin Ganesh, M.; John, Bibin

2018-01-01

Numerical optimization of hypersonic drag reduction technique based on concentrated energy addition is presented in this study. A reduction in wave drag is realized through concentrated energy addition in the hypersonic flowfield upstream of the blunt body. For the exhaustive optimization presented in this study, an in-house high precision inviscid flow solver has been developed. Studies focused on the identification of "optimum energy addition location" have revealed the existence of multiple minimum drag points. The wave drag coefficient is observed to drop from 0.85 to 0.45 when 50 Watts of energy is added to an energy bubble of 1 mm radius located at 74.7 mm upstream of the stagnation point. A direct proportionality has been identified between energy bubble size and wave drag coefficient. Dependence of drag coefficient on the upstream added energy magnitude is also revealed. Of the observed multiple minimum drag points, the energy deposition point (EDP) that offers minimum wave drag just after a sharp drop in drag is proposed as the most optimum energy addition location.

The effect of dendrimer on cotton dyeability with direct dyes

Directory of Open Access Journals (Sweden)

Khakzar Bafrooei F.

2014-01-01

Full Text Available Pretreatment of cotton fabric with poly(propylene imine dendrimer enhanced its colour strength using C.I. Direct Red 81 and C.I. Direct Blue 78. Application of this dendrimer and the direct dye simultaneously on cotton fabric by the exhaust and the continuous dyeing method were studied; slight improvements in the dyeing results were obtained. Pretreatment of the cotton fabric with dendrimer in an emulsion form using the pad-dry method followed by continuous dyeing markedly increased the colour strength. In addition, level dyeing was obtained, and no negative effects on the fastness properties of the dyes used were observed.

Problem of data privacy protection in direct marketing

Directory of Open Access Journals (Sweden)

Markov Jasmina

2011-01-01

Full Text Available The dynamism of modern business conditions, as well as increasing competition, call for companies to change their usual ways of doing business and communicating with consumers. Therefore, today's direct marketing industry is experiencing explosive growth, as more and more companies include these activities in their communication mix. Many companies benefit from the development and usage of direct marketing, but at the same time, its growing usage led to numerous problems for companies as well as for the consumers. Direct marketing, advanced information technologies and Internet, on whose use it is more and more based, caused a number of legal and ethical questions without precedent. One of the issues that is making consumers more and more worried is concerning the privacy of their personal data and information which is being collected by a large number of companies. In addition, consumers are often not aware of this data collecting, which is adding even more gravity to this problem. The remainder of this paper will point to the necessity and great importance of careful and responsible use of consumer's personal data by direct marketers, with the aim of build long-term partnership relationships between the two. In addition, special attention will be paid to major problems that consumers face today in the field of data protection, as well as to the efforts committed in order to bring these problems to a minimum by getting consumers more involved in making decisions about usage of their personal data and information.

Delphi's new direct acting common rail injection system; Das neue Direct Acting Common Rail System von Delphi

Energy Technology Data Exchange (ETDEWEB)

Schoeppe, Detlev; Zuelch, Stefan; Geurts, Derk; Gris, Christian; Jorach, Rainer W. [Delphi Diesel Systems, Europe (United Kingdom)

2009-07-01

With the serial start of the Direct Acting Common Rail injection system with 2.000 bar Delphi Diesel Systems could supplement its product portfolio with a valuable component. In Delphi's directly propelled Common Rail injector, the Injection needle directly is set in operation with the help of a piezo-ceramic actuator instead of only controlling this with a conventional servo-hydraulic circuit indirectly. This enables a fast opening and closing of the nozzle needle possible independently from the rail pressure. The process of injection is controllable accurately at any time with the again developed two-stage needle movement amplifier. The additionally in the injector integrated fuel storage works as a 'Rail in the Injector' and improves the quality particularly during multiple injection. The injector completely works leakage-free and thereby helps to reach the future CO{sub 2} targets. The use of piezo-actuators as driving force behind the directly working injector leads to a set of requirements to the electronics. A control electronics was developed in order to head optimally the Direct Acting Injector. The sum of all advantages of the Direct Acting of CR systems enables lowest emissions with simultaneously small fuel consumption while new dimensions are reached with power density and engine torque. The authors of the contribution under consideration report on the construction, on the work principle of the Direct Acting CR system and on its performance characteristics as a basis for the premium diesel engine.

Preferences for Advance Directives in Korea

Directory of Open Access Journals (Sweden)

So-Sun Kim

2012-01-01

Full Text Available Background. The goal of advance directives is to help patients retain their dignity and autonomy by making their own decisions regarding end-stage medical treatment. The purpose of this study was to examine preferences of advance directives among general population in Korea. Method. A descriptive cross-sectional survey was performed from October 2007 to June 2008 in Seoul, Korea. A total of 336 city-dwelling adults self-administered the questionnaire and returned it via mail. Data analyses were conducted using SPSS 17.0. Results. Subjects reported the need for healthcare providers' detailed explanations and recommendations regarding end-of-life care. When there is no hope of recovery and death is imminent, most subjects did not want to receive cardiopulmonary resuscitation nor an IV or tube feeding. However, most of the subjects wanted pain management care. Conclusions. The present study showed that many Korean people have an interest in advance directives. The results show that the autonomy and dignity of patient have increased in importance. To provide better end-of-life care, there is a need to educate patients on the definition and intent of an advance directive. Additional proactive communication between patients and their caregivers should be educated to healthcare providers.

Influence of metallic based fuel additives on performance and exhaust emissions of diesel engine

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin, E-mail: mguru@gazi.edu.t [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

2011-01-15

In this experimental study, influence of the metallic-based additives on fuel consumption and exhaust emissions of diesel engine were investigated. The metallic-based additives were produced by synthesizing of resin acid (abietic acid) with MnO{sub 2} or MgO. These additives were doped into diesel fuel at the rate of 8 {mu}mol/l and 16 {mu}mol/l for preparing test fuels. Both additives improved the properties of diesel fuel such as viscosity, flash point, cloud point and pour point. The fuels with and without additives were tested in a direct injection diesel engine at full load condition. Maximum reduction of specific fuel consumption was recorded as 4.16%. CO emission and smoke opacity decreased by 16.35% and by 29.82%, respectively. NO{sub x} emission was measured higher and CO{sub 2} emission was not changed considerably with the metallic-based additives.

Defining an additivity framework for mixture research in inducible whole-cell biosensors

DEFF Research Database (Denmark)

Martin-Betancor, K; Ritz, Christian; Fernández-Piñas, F

2015-01-01

A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts for differe......A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts...... for differential maximal effects among analytes and response inhibition beyond the maximum permissive concentrations. This allows a multivariate extension of Loewe additivity, enabling direct application in a biphasic dose-response framework. The proposed additivity definition was validated, and its applicability...... illustrated by studying the response of the cyanobacterial biosensor Synechococcus elongatus PCC 7942 pBG2120 to binary mixtures of Zn, Cu, Cd, Ag, Co and Hg. The novel method allowed by the first time to model complete dose-response profiles of an inducible whole cell biosensor to mixtures. In addition...

OCT evaluation of directional atherectomy compared to balloon angioplasty

International Nuclear Information System (INIS)

Marmagkiolis, Konstantinos; Lendel, Vasili; Cilingiroglu, Mehmet

2015-01-01

Directional atherectomy (DA) is one of the most commonly used modalities for the treatment of obstructive femoropopliteal peripheral arterial disease (PAD), especially in patients with large and calcified atherosclerotic plaques. The effect of directional atherectomy to the vascular wall compared to balloon angioplasty by optical coherence tomography (OCT) has not been previously described. We present the first case of OCT after directional atherectomy with SilverHawk followed by angiosculpt balloon angioplasty. - Highlights: • Directional atherectomy avoids the vascular mechanical damage caused by angioplasty balloons and the exposure of stent struts or the potential of stent fracture with stents. • OCT can accurately assess the effect of endovacular interventions to the vessel wall. • Although angiographic results after directional atherectomy are acceptable, OCT use demonstrated suboptimal improvement of the MLA requiring additional balloon angioplasty. • Longer studies are needed to define whether the improved OCT results with angioplasty compared to DA may offer better clinical outcomes.

OCT evaluation of directional atherectomy compared to balloon angioplasty

Energy Technology Data Exchange (ETDEWEB)

Marmagkiolis, Konstantinos [Citizens Memorial Hospital Heart and Vascular Institute, Bolivar, MO (United States); Lendel, Vasili [Arkansas Heart Hospital, Peripheral Vascular Institute, Little Rock, AR (United States); Cilingiroglu, Mehmet, E-mail: mcilingiroglu@yahoo.com [Arkansas Heart Hospital, Peripheral Vascular Institute, Little Rock, AR (United States); Koc University, School of Medicine, Istanbul (Turkey)

2015-09-15

Directional atherectomy (DA) is one of the most commonly used modalities for the treatment of obstructive femoropopliteal peripheral arterial disease (PAD), especially in patients with large and calcified atherosclerotic plaques. The effect of directional atherectomy to the vascular wall compared to balloon angioplasty by optical coherence tomography (OCT) has not been previously described. We present the first case of OCT after directional atherectomy with SilverHawk followed by angiosculpt balloon angioplasty. - Highlights: • Directional atherectomy avoids the vascular mechanical damage caused by angioplasty balloons and the exposure of stent struts or the potential of stent fracture with stents. • OCT can accurately assess the effect of endovacular interventions to the vessel wall. • Although angiographic results after directional atherectomy are acceptable, OCT use demonstrated suboptimal improvement of the MLA requiring additional balloon angioplasty. • Longer studies are needed to define whether the improved OCT results with angioplasty compared to DA may offer better clinical outcomes.

Concentric artificial impedance surface for directional sound beamforming

Directory of Open Access Journals (Sweden)

Kyungjun Song

2017-03-01

Full Text Available Utilizing acoustic metasurfaces consisting of subwavelength resonant textures, we design an artificial impedance surface by creating a new boundary condition. We demonstrate a circular artificial impedance surface with surface impedance modulation for directional sound beamforming in three-dimensional space. This artificial impedance surface is implemented by revolving two-dimensional Helmholtz resonators with varying internal coiled path. Physically, the textured surface has inductive surface impedance on its inner circular patterns and capacitive surface impedance on its outer circular patterns. Directional receive beamforming can be achieved using an omnidirectional microphone located at the focal point formed by the gradient-impeding surface. In addition, the uniaxial surface impedance patterning inside the circular aperture can be used for steering the direction of the main lobe of the radiation pattern.

3D Printing, Additive Manufacturing, and Solid Freeform Fabrication: The Technologies of the Past, Present and Future

Science.gov (United States)

Beaman, Joseph

2015-03-01

Starting in the late 1980's, several new technologies were created that have the potential to revolutionize manufacturing. These technologies are, for the most part, additive processes that build up parts layer by layer. In addition, the processes that are being touted for hard-core manufacturing are primarily laser or e-beam based processes. This presentation gives a brief history of Additive Manufacturing and gives an assessment for these technologies. These technologies initially grew out of a commercial need for rapid prototyping. This market has a different requirement for process and quality control than traditional manufacturing. The relatively poor process control of the existing commercial Additive Manufacturing equipment is a vestige of this history. This presentation discusses this history and improvements in quality over time. The emphasis will be on Additive Manufacturing processes that are being considered for direct manufacturing, which is a different market than the 3D Printing ``Makerbot'' market. Topics discussed include past and present machine sensors, materials, and operational methods that were used in the past and those that are used today to create manufactured parts. Finally, a discussion of new methods and future directions of AM is presented.

Synthesis of γ-Nitro Aliphatic Methyl Esters Via Michael Additions Promoted by Microwave Irradiation

OpenAIRE

Escalante, Jaime; Díaz-Coutiño, Francisco D.

2009-01-01

A simple and efficient protocol has been developed for the direct synthesis of γ-nitrobutyric acid methyl esters under microwave irradiation. This methodology reduces reaction times from days to minutes, compared to conventional conditions. Additionally, these conditions increased yields and provided cleaner reactions.

Mechanical Behavior of Additive Manufactured Layered Materials, Part 2: Stainless Steels

Science.gov (United States)

2015-04-30

materials. Elsevier, Oxford; 2007: 416 -420. [19] Deng, D., Chen, R., Sun, Q. and Li, X. Microstructural study of 17-4PH stainless steel after plasma...1 Mechanical Behavior of Additive Manufactured Layered Materials, Part 2: Stainless Steels * Todd M. Mower † and Michael J. Long M.I.T. Lincoln... stainless steel alloys produced with Direct Metal Laser Sintering (DMLS) was measured and is compared to that of similar conventional materials

Additive manufacturing.

Science.gov (United States)

Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

2018-04-01

Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

Targeted Structural Optimization with Additive Manufacturing of Metals

Science.gov (United States)

Burt, Adam; Hull, Patrick

2015-01-01

The recent advances in additive manufacturing (AM) of metals have now improved the state-of-the-art such that traditionally non-producible parts can be readily produced in a cost-effective way. Because of these advances in manufacturing technology, structural optimization techniques are well positioned to supplement and advance this new technology. The goal of this project is to develop a structural design, analysis, and optimization framework combined with AM to significantly light-weight the interior of metallic structures while maintaining the selected structural properties of the original solid. This is a new state-of-the-art capability to significantly reduce mass, while maintaining the structural integrity of the original design, something that can only be done with AM. In addition, this framework will couple the design, analysis, and fabrication process, meaning that what has been designed directly represents the produced part, thus closing the loop on the design cycle and removing human iteration between design and fabrication. This fundamental concept has applications from light-weighting launch vehicle components to in situ resource fabrication.

Directional atherectomy for treatment of restenosis within coronary stents: clinical, angiographic and histologic results

NARCIS (Netherlands)

B.H. Strauss (Bradley); V.A.W.M. Umans (Victor); R-J. van Suylen (Robert-Jan); P.J. de Feyter (Pim); J. Marco (Jean); G. Robertson; J. Renkin; G.R. Heyndrickx (Guy); V.D. Vuzevski (Vojislav); F.T.B. Bosman (Fré); P.W.J.C. Serruys (Patrick)

1992-01-01

textabstractAbstract OBJECTIVES: The safety and long-term results of directional coronary atherectomy in stented coronary arteries were determined. In addition, tissue studies were performed to characterize the development of restenosis. METHODS: Directional coronary atherectomy was performed in

Direct Coal Oxidation in Modified Solid Oxide Fuel Cells

DEFF Research Database (Denmark)

Deleebeeck, Lisa; Gil, Vanesa; Ippolito, Davide

2017-01-01

Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon-carbonate s......Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon......-carbonate slurry or anode layer. The nature of the coal affects both open circuit voltage and power output. Highest OCV and power densities were observed for bituminous coal and by adding manganese oxide or praseodymium-doped ceria to the carbon/carbonate mixture. Comparing the carbon black fueled performance...... bituminous coal (73 mW/cm2)....

Molybdenum-containing acidic catalysts to convert cellulosic biomass to glycolic acid

KAUST Repository

Han, Yu

2014-09-30

Embodiments of the present invention include methods and compositions related to catabolic conversion of cellulosic biomass to glycolic acid using molybdenum-containing acidic catalysts. The invention includes the use of heteropoly and isopoly acids and salts as the molybdenum-containing multi-functional catalysts for biomass conversion. In embodiments of the invention, the reactions employ successive hydrolysis, retro-aldol fragmentation, and selective oxidation in a noble metal-free system.

(E-3-Methyl-6-(3-oxo-3-(3,4,5-trimethoxyphenylprop-1-en-1-yl-2(3H-benzothiazolone

Directory of Open Access Journals (Sweden)

Yordanka Ivanova

2016-09-01

Full Text Available The title compound, (E-3-methyl-6-(3-oxo-3-(3,4,5-trimethoxyphenylprop-1-en-1-yl-2(3H-benzothiazolone, was synthesized by both an acid- and base-catalyzed aldol condensation of 3-methyl-6-acetyl-2(3H-benzothiazolone and 3,4,5-trimethoxyacetophenone. The structure of the target compound was confirmed using 1H-NMR, 13C-NMR, IR, MS, and elemental analysis.

Directed polymers versus directed percolation

Science.gov (United States)

Halpin-Healy, Timothy

1998-10-01

Universality plays a central role within the rubric of modern statistical mechanics, wherein an insightful continuum formulation rises above irrelevant microscopic details, capturing essential scaling behaviors. Nevertheless, occasions do arise where the lattice or another discrete aspect can constitute a formidable legacy. Directed polymers in random media, along with its close sibling, directed percolation, provide an intriguing case in point. Indeed, the deep blood relation between these two models may have sabotaged past efforts to fully characterize the Kardar-Parisi-Zhang universality class, to which the directed polymer belongs.

No detectable fertility benefit from a single additional mating in wild stalk-eyed flies.

Directory of Open Access Journals (Sweden)

Elisabeth Harley

2010-12-01

Full Text Available Multiple mating by female insects is widespread, and the explanation(s for repeated mating by females has been the subject of much discussion. Females may profit from mating multiply through direct material benefits that increase their own reproductive output, or indirect genetic benefits that increase offspring fitness. One particular direct benefit that has attracted significant attention is that of fertility assurance, as females often need to mate multiply to achieve high fertility. This hypothesis has never been tested in a wild insect population.Female Malaysian stalk-eyed flies (Teleopsis dalmanni mate repeatedly during their lifetime, and have been shown to be sperm limited under both laboratory and field conditions. Here we ask whether receiving an additional mating alleviates sperm limitation in wild females. In our experiment one group of females received a single additional mating, while a control group received an interrupted, and therefore unsuccessful, mating. Females that received an additional mating did not lay more fertilised eggs in total, nor did they lay proportionately more fertilised eggs. Female fertility declined significantly through time, demonstrating that females were sperm limited. However, receipt of an additional mating did not significantly alter the rate of this decline.Our data suggest that the fertility consequences of a single additional mating were small. We discuss this effect (or lack thereof, and suggest that it is likely to be attributed to small ejaculate size, a high proportion of failed copulations, and the presence of X-linked meiotic drive in this species.

Additively Manufactured IN718 Components with Wirelessly Powered and Interrogated Embedded Sensing

Energy Technology Data Exchange (ETDEWEB)

Attridge, Paul [United Technologies Research Center, East Hartford, CT (United States); Bajekal, Sanjay [United Technologies Research Center, East Hartford, CT (United States); Klecka, Michael [United Technologies Research Center, East Hartford, CT (United States); Wu, Xin [United Technologies Research Center, East Hartford, CT (United States); Savulak, Steve [United Technologies Research Center, East Hartford, CT (United States); Viens, Dan [United Technologies Research Center, East Hartford, CT (United States); Carey, Michael [United Technologies Research Center, East Hartford, CT (United States); Miano, John [United Technologies Research Center, East Hartford, CT (United States); Rioux, William [United Technologies Research Center, East Hartford, CT (United States); Zacchio, Joseph [United Technologies Research Center, East Hartford, CT (United States); Dunst, Richard [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Straub, Doug [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Mantese, Joseph [United Technologies Research Center, East Hartford, CT (United States)

2017-07-14

A methodology is described for embedding commercial-off-the-shelf sensors together with wireless communication and power circuit elements using direct laser metal sintered additively manufactured components. Physics based models of the additive manufacturing processes and sensor/wireless level performance models guided the design and embedment processes. A combination of cold spray deposition and laser engineered net shaping was used to fashion the transmitter/receiving elements and embed the sensors, thereby providing environmental protection and component robustness/survivability for harsh conditions. By design, this complement of analog and digital sensors were wirelessly powered and interrogated using a health and utilization monitoring system; enabling real-time, in situ prognostics and diagnostics.

5 CFR 8301.103 - Additional rules for employees of the Farm Service Agency.

Science.gov (United States)

2010-01-01

... SUPPLEMENTAL STANDARDS OF ETHICAL CONDUCT FOR EMPLOYEES OF THE DEPARTMENT OF AGRICULTURE § 8301.103 Additional... estate purchases. (1) No FSA employee, or spouse or minor child of an FSA employee, may directly or indirectly purchase real estate held in the FSA inventory, for sale under forfeiture to FSA, or from an FSA...

Laser-based direct-write techniques for cell printing

Energy Technology Data Exchange (ETDEWEB)

Schiele, Nathan R; Corr, David T [Biomedical Engineering Department, Rensselaer Polytechnic Institute, Troy, NY (United States); Huang Yong [Department of Mechanical Engineering, Clemson University, Clemson, SC (United States); Raof, Nurazhani Abdul; Xie Yubing [College of Nanoscale Science and Engineering, University at Albany, SUNY, Albany, NY (United States); Chrisey, Douglas B, E-mail: schien@rpi.ed, E-mail: chrisd@rpi.ed [Material Science and Engineering Department, Rensselaer Polytechnic Institute, Troy, NY (United States)

2010-09-15

Fabrication of cellular constructs with spatial control of cell location ({+-}5 {mu}m) is essential to the advancement of a wide range of applications including tissue engineering, stem cell and cancer research. Precise cell placement, especially of multiple cell types in co- or multi-cultures and in three dimensions, can enable research possibilities otherwise impossible, such as the cell-by-cell assembly of complex cellular constructs. Laser-based direct writing, a printing technique first utilized in electronics applications, has been adapted to transfer living cells and other biological materials (e.g., enzymes, proteins and bioceramics). Many different cell types have been printed using laser-based direct writing, and this technique offers significant improvements when compared to conventional cell patterning techniques. The predominance of work to date has not been in application of the technique, but rather focused on demonstrating the ability of direct writing to pattern living cells, in a spatially precise manner, while maintaining cellular viability. This paper reviews laser-based additive direct-write techniques for cell printing, and the various cell types successfully laser direct-written that have applications in tissue engineering, stem cell and cancer research are highlighted. A particular focus is paid to process dynamics modeling and process-induced cell injury during laser-based cell direct writing. (topical review)

Laser-based direct-write techniques for cell printing

International Nuclear Information System (INIS)

Schiele, Nathan R; Corr, David T; Huang Yong; Raof, Nurazhani Abdul; Xie Yubing; Chrisey, Douglas B

2010-01-01

Fabrication of cellular constructs with spatial control of cell location (±5 μm) is essential to the advancement of a wide range of applications including tissue engineering, stem cell and cancer research. Precise cell placement, especially of multiple cell types in co- or multi-cultures and in three dimensions, can enable research possibilities otherwise impossible, such as the cell-by-cell assembly of complex cellular constructs. Laser-based direct writing, a printing technique first utilized in electronics applications, has been adapted to transfer living cells and other biological materials (e.g., enzymes, proteins and bioceramics). Many different cell types have been printed using laser-based direct writing, and this technique offers significant improvements when compared to conventional cell patterning techniques. The predominance of work to date has not been in application of the technique, but rather focused on demonstrating the ability of direct writing to pattern living cells, in a spatially precise manner, while maintaining cellular viability. This paper reviews laser-based additive direct-write techniques for cell printing, and the various cell types successfully laser direct-written that have applications in tissue engineering, stem cell and cancer research are highlighted. A particular focus is paid to process dynamics modeling and process-induced cell injury during laser-based cell direct writing. (topical review)

Study on thermal effects & sulfurized additives, in lubricating greases

Science.gov (United States)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Study on the combustion and hydrocarbon emission characteristics of direct injection spark-ignition engines during the direct-start process

International Nuclear Information System (INIS)

Shi, Lei; Xiao, Maoyu; Deng, Kangyao

2015-01-01

Highlights: • Mixture concentration in first-combustion cylinder of direct start is measured. • Factors that affect direct start performances are investigated. • Combustion characteristics of first-combustion cylinder are analyzed. • Hydrocarbon emission is considered to determined control strategies of direct start. - Abstract: This study was conducted to investigate the combustion and emissions characteristics of the first-combustion cylinder in a direct-start process. The explosive energy of the first combustion is important for the success of a direct start, but this combustion was rarely addressed in recent research. For a 2.0 L direct-injection spark-ignition engine, the in-cylinder mixture concentration, cylinder pressure, engine speed and exhaust hydrocarbon concentration were detected to analyze the fuel evaporation, combustion, engine movement and engine emissions, respectively. In the first-combustion cylinder of the direct-start process, the injected fuel was often enriched to ensure that an appropriate mixture concentration was obtained for ignition without misfiring. Approximately one-third of the injected fuel would not participate in the combustion process and would therefore reduce the exhaust hydrocarbon emissions. The start position determined the amount of the total explosive energy in the first-combustion cylinder, and an optimal start position for a direct start was found to be at a 70–80° crank angle before the top dead center to obtain a better combustion performance and lower emissions. A lower coolant temperature increased the maximum explosion energy of the first combustion, but additional hydrocarbon emissions were generated. Because there was almost no problem in the direct-start capability with different coolant temperatures after an idling stop, it was necessary to maintain the coolant temperature when the engine was stopped

Genomic Model with Correlation Between Additive and Dominance Effects.

Science.gov (United States)

Xiang, Tao; Christensen, Ole Fredslund; Vitezica, Zulma Gladis; Legarra, Andres

2018-05-09

Dominance genetic effects are rarely included in pedigree-based genetic evaluation. With the availability of single nucleotide polymorphism markers and the development of genomic evaluation, estimates of dominance genetic effects have become feasible using genomic best linear unbiased prediction (GBLUP). Usually, studies involving additive and dominance genetic effects ignore possible relationships between them. It has been often suggested that the magnitude of functional additive and dominance effects at the quantitative trait loci are related, but there is no existing GBLUP-like approach accounting for such correlation. Wellmann and Bennewitz showed two ways of considering directional relationships between additive and dominance effects, which they estimated in a Bayesian framework. However, these relationships cannot be fitted at the level of individuals instead of loci in a mixed model and are not compatible with standard animal or plant breeding software. This comes from a fundamental ambiguity in assigning the reference allele at a given locus. We show that, if there has been selection, assigning the most frequent as the reference allele orients the correlation between functional additive and dominance effects. As a consequence, the most frequent reference allele is expected to have a positive value. We also demonstrate that selection creates negative covariance between genotypic additive and dominance genetic values. For parameter estimation, it is possible to use a combined additive and dominance relationship matrix computed from marker genotypes, and to use standard restricted maximum likelihood (REML) algorithms based on an equivalent model. Through a simulation study, we show that such correlations can easily be estimated by mixed model software and accuracy of prediction for genetic values is slightly improved if such correlations are used in GBLUP. However, a model assuming uncorrelated effects and fitting orthogonal breeding values and dominant

Machinability of Al 6061 Deposited with Cold Spray Additive Manufacturing

Science.gov (United States)

Aldwell, Barry; Kelly, Elaine; Wall, Ronan; Amaldi, Andrea; O'Donnell, Garret E.; Lupoi, Rocco

2017-10-01

Additive manufacturing techniques such as cold spray are translating from research laboratories into more mainstream high-end production systems. Similar to many additive processes, finishing still depends on removal processes. This research presents the results from investigations into aspects of the machinability of aluminum 6061 tubes manufactured with cold spray. Through the analysis of cutting forces and observations on chip formation and surface morphology, the effect of cutting speed, feed rate, and heat treatment was quantified, for both cold-sprayed and bulk aluminum 6061. High-speed video of chip formation shows changes in chip form for varying material and heat treatment, which is supported by the force data and quantitative imaging of the machined surface. The results shown in this paper demonstrate that parameters involved in cold spray directly impact on machinability and therefore have implications for machining parameters and strategy.

Direct seeding woody species for restoration of bottomlands

Science.gov (United States)

Twedt, D.J.; Connor, Kristina F

2006-01-01

I direct seeded (broadcast) seeds of 39 species of trees and shrubs using an ATV-mounted rotary spreader to initiate restoration of bottomland forest on retired agricultural sites. Four sites were planted during February, 2000, and 13 additional sites were planted during April and May, 2001. After two growing seasons, stem density of direct-seeded species varied greatly among study plots (range = 0 to 888 stems/ha) but averaged only 110 stems/ha. I recommend that future efforts at direct seeding focus on seven shrub species (Amorpha fruticosa L., Cephalanthus occidentalis L., Cornus spp., Crataegus spp., Ilex decidua Walt., Morus rubra L., and Prunus spp.) and seven tree species (Celtis laevigata Willd., Diospyros virginiana L., Fraxinus spp., Gleditsia triacanthos L., Robinia pseudoacacia L., Taxodium distichum (L.) Rich, and Ulmus spp.) that successfully established in these trials.

Synthesis of γ-Nitro Aliphatic Methyl Esters Via Michael Additions Promoted by Microwave Irradiation

Directory of Open Access Journals (Sweden)

Francisco D. Díaz-Coutiño

2009-04-01

Full Text Available A simple and efficient protocol has been developed for the direct synthesis of γ-nitrobutyric acid methyl esters under microwave irradiation. This methodology reduces reaction times from days to minutes, compared to conventional conditions. Additionally, these conditions increased yields and provided cleaner reactions.

Hybrid fabrication process of additive manufacturing and direct writing for a 4 X 4 mm matrix flexible tactile sensor

Energy Technology Data Exchange (ETDEWEB)

Woo, Sang Gu; Lee, In Hwan [Chungbuk National University, Chungju (Korea, Republic of); Lee, Kyong Chang [Pukyong National University, Busan (Korea, Republic of)

2015-09-15

Various machines require data from their external environments for safety and/or accuracy. In this respect, many sensors that mimic the human sensory system have been investigated. Among these, tactile sensors may be useful for obtaining data on the roughness of, and external forces acting upon, an object. Several tactile sensors have been developed; however, these are typically fabricated via a series of complex processes, and hence are unsuitable for volume manufacturing. In this paper, we report a fabrication process for a 4 X 4 mm matrix flexible sensor element using layered manufacturing and direct-write technology. A composite composed of photocurable resin and Multi-walled carbon nanotubes (MWCNTs) was used as the sensing material. The MWCNTs were mixed with the photocurable resin using ultrasonic dispersion, and the liquid mixture exhibited excellent piezoresistive properties following curing using ultraviolet light. The used photocurable resin is flexible and elastic after curing. Therefore, the composite material can be bent and deformed. To use this composite material with the flexible sensor, dispensing characteristics were examined using direct-write technology. For the acquisition of sensor data, a commercial pin-header was inserted and photocurable resin was filled up to the height of pin-header and cured . Then, the composite material was dispensed onto the pin-header as a sensing material. Using this process, a flexible sensor with piezoresistive properties was formed.

Hybrid fabrication process of additive manufacturing and direct writing for a 4 X 4 mm matrix flexible tactile sensor

International Nuclear Information System (INIS)

Woo, Sang Gu; Lee, In Hwan; Lee, Kyong Chang

2015-01-01

Various machines require data from their external environments for safety and/or accuracy. In this respect, many sensors that mimic the human sensory system have been investigated. Among these, tactile sensors may be useful for obtaining data on the roughness of, and external forces acting upon, an object. Several tactile sensors have been developed; however, these are typically fabricated via a series of complex processes, and hence are unsuitable for volume manufacturing. In this paper, we report a fabrication process for a 4 X 4 mm matrix flexible sensor element using layered manufacturing and direct-write technology. A composite composed of photocurable resin and Multi-walled carbon nanotubes (MWCNTs) was used as the sensing material. The MWCNTs were mixed with the photocurable resin using ultrasonic dispersion, and the liquid mixture exhibited excellent piezoresistive properties following curing using ultraviolet light. The used photocurable resin is flexible and elastic after curing. Therefore, the composite material can be bent and deformed. To use this composite material with the flexible sensor, dispensing characteristics were examined using direct-write technology. For the acquisition of sensor data, a commercial pin-header was inserted and photocurable resin was filled up to the height of pin-header and cured . Then, the composite material was dispensed onto the pin-header as a sensing material. Using this process, a flexible sensor with piezoresistive properties was formed.

Explosion-proof actuators according to EU directive 94/9/EC (ATEX)

Energy Technology Data Exchange (ETDEWEB)

Herbstritt, M. [AUMA Riester GmbH und Co. KG. Muellheim (Germany)

2004-07-01

Since July, 1, 2003 only explosion-proof devices which conform to the new EU Directive 94/9/EC, better known as the ATEX Directive, are introduced to the market. Especially the explosion protection of non-electrical equipment is a completely new task for many manufacturers. AUMA has qualified its electric actuators for the automation of industrial valves in accordance with the new regulations. In addition the design has been improved. (orig.)

Predictive modeling of solidification during laser additive manufacturing of nickel superalloys: recent developments, future directions

Science.gov (United States)

Ghosh, Supriyo

2018-01-01

Additive manufacturing (AM) processes produce parts with improved physical, chemical, and mechanical properties compared to conventional manufacturing processes. In AM processes, intricate part geometries are produced from multicomponent alloy powder, in a layer-by-layer fashion with multipass laser melting, solidification, and solid-state phase transformations, in a shorter manufacturing time, with minimal surface finishing, and at a reasonable cost. However, there is an increasing need for post-processing of the manufactured parts via, for example, stress relieving heat treatment and hot isostatic pressing to achieve homogeneous microstructure and properties at all times. Solidification in an AM process controls the size, shape, and distribution of the grains, the growth morphology, the elemental segregation and precipitation, the subsequent solid-state phase changes, and ultimately the material properties. The critical issues in this process are linked with multiphysics (such as fluid flow and diffusion of heat and mass) and multiscale (lengths, times and temperature ranges) challenges that arise due to localized rapid heating and cooling during AM processing. The alloy chemistry-process-microstructure-property-performance correlation in this process will be increasingly better understood through multiscale modeling and simulation.

Direct Coal Oxidation in Modified Solid Oxide Fuel Cells

DEFF Research Database (Denmark)

Deleebeeck, Lisa; Gil, Vanesa; Ippolito, Davide

2015-01-01

Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon-carbonate s......Hybrid direct carbon fuel cells employ a classical solid oxide fuel cell together with carbon dispersed in a carbonate melt on the anode side. In a European project, the utilization of various coals has been investigated with and without addition of an oxidation catalyst to the carbon......-carbonate slurry or anode layer. The nature of the coal affects both open circuit voltage and power output. Highest OCV and power densities were observed for bituminous coal and by adding manganese oxide or praseodymium-doped ceria to the carbon/carbonate mixture. Comparing the carbon black fueled performance...... bituminous coal (73 mW/cm2). © 2015 ECS - The Electrochemical Society...

Diffusion properties of active particles with directional reversal

International Nuclear Information System (INIS)

Großmann, R; Bär, M; Peruani, F

2016-01-01

The diffusion properties of self-propelled particles which move at constant speed and, in addition, reverse their direction of motion repeatedly are investigated. The internal dynamics of particles triggering these reversal processes is modeled by a stochastic clock. The velocity correlation function as well as the mean squared displacement is investigated and, furthermore, a general expression for the diffusion coefficient for self-propelled particles with directional reversal is derived. Our analysis reveals the existence of an optimal, finite rotational noise amplitude which maximizes the diffusion coefficient. We comment on the relevance of these results with regard to biological systems and suggest further experiments in this context. (paper)

effects of sulphur addition on addition on and mechanical properties

African Journals Online (AJOL)

User

234-8034714355. 8034714355. 1. EFFECTS OF SULPHUR ADDITION ON. ADDITION ON. 2. AND MECHANICAL PROPERTIES O. 3. 4. C. W. Onyia. 5. 1DEPT. OF METALLURGICAL AND MATERIALS. 6. 2, 4DEPT. OF METALLURGICAL ...

Temporal correlation coefficient for directed networks.

Science.gov (United States)

Büttner, Kathrin; Salau, Jennifer; Krieter, Joachim

2016-01-01

Previous studies dealing with network theory focused mainly on the static aggregation of edges over specific time window lengths. Thus, most of the dynamic information gets lost. To assess the quality of such a static aggregation the temporal correlation coefficient can be calculated. It measures the overall possibility for an edge to persist between two consecutive snapshots. Up to now, this measure is only defined for undirected networks. Therefore, we introduce the adaption of the temporal correlation coefficient to directed networks. This new methodology enables the distinction between ingoing and outgoing edges. Besides a small example network presenting the single calculation steps, we also calculated the proposed measurements for a real pig trade network to emphasize the importance of considering the edge direction. The farm types at the beginning of the pork supply chain showed clearly higher values for the outgoing temporal correlation coefficient compared to the farm types at the end of the pork supply chain. These farm types showed higher values for the ingoing temporal correlation coefficient. The temporal correlation coefficient is a valuable tool to understand the structural dynamics of these systems, as it assesses the consistency of the edge configuration. The adaption of this measure for directed networks may help to preserve meaningful additional information about the investigated network that might get lost if the edge directions are ignored.

Direct currents produced by hf heating of plasma

International Nuclear Information System (INIS)

Klima, R.

1974-01-01

In addition to the well-known diffusion currents, toroidal direct currents arise in h.f. heated plasmas as a result of a momentum transfer from the h.f. field to plasma particles. The estimates of steady-state conditions are given for these currents. Particularly, the possibility of stationary operation of a Tokamak device is analyzed. (author)

Analysis of primary cilia in directional cell migration in fibroblasts

DEFF Research Database (Denmark)

Christensen, Søren Tvorup; Veland, Iben; Schwab, Albrecht

2013-01-01

summarize selected methods in analyzing ciliary function in directional cell migration, including immunofluorescence microscopy, scratch assay, and chemotaxis assay by micropipette addition of PDGFRα ligands to cultures of fibroblasts. These methods should be useful not only in studying cell migration....... In particular, platelet-derived growth factor receptor alpha (PDGFRα) is compartmentalized to the primary cilium to activate signaling pathways that regulate reorganization of the cytoskeleton required for lamellipodium formation and directional migration in the presence of a specific ligand gradient. We...

Kinetics of Hydrogen Abstraction and Addition Reactions of 3-Hexene by ȮH Radicals.

Science.gov (United States)

Yang, Feiyu; Deng, Fuquan; Pan, Youshun; Zhang, Yingjia; Tang, Chenglong; Huang, Zuohua

2017-03-09

Rate coefficients of H atom abstraction and H atom addition reactions of 3-hexene by the hydroxyl radicals were determined using both conventional transition-state theory and canonical variational transition-state theory, with the potential energy surface (PES) evaluated at the CCSD(T)/CBS//BHandHLYP/6-311G(d,p) level and quantum mechanical effect corrected by the compounded methods including one-dimensional Wigner method, multidimensional zero-curvature tunneling method, and small-curvature tunneling method. Results reveal that accounting for approximate 70% of the overall H atom abstractions occur in the allylic site via both direct and indirect channels. The indirect channel containing two van der Waals prereactive complexes exhibits two times larger rate coefficient relative to the direct one. The OH addition reaction also contains two van der Waals complexes, and its submerged barrier results in a negative temperature coefficient behavior at low temperatures. In contrast, The OH addition pathway dominates only at temperatures below 450 K whereas the H atom abstraction reactions dominate overwhelmingly at temperature over 1000 K. All of the rate coefficients calculated with an uncertainty of a factor of 5 were fitted in a quasi-Arrhenius formula. Analyses on the PES, minimum reaction path and activation free Gibbs energy were also performed in this study.

Multi-Pole HTS Generators for Direct Drive Wind Turbines

DEFF Research Database (Denmark)

Jensen, Bogi Bech; Abrahamsen, Asger Bech; Seiler, Eugen

or the performance of the coated conductor has to improve significantly (by a factor of 10 or more) in order for HTS generators to become feasible in direct drive offshore wind turbines. This price/performance improvement is not unrealistic in the coming decade. Additionally the reliability of such machines...

Direct adaptive control using feedforward neural networks

OpenAIRE

Cajueiro, Daniel Oliveira; Hemerly, Elder Moreira

2003-01-01

ABSTRACT: This paper proposes a new scheme for direct neural adaptive control that works efficiently employing only one neural network, used for simultaneously identifying and controlling the plant. The idea behind this structure of adaptive control is to compensate the control input obtained by a conventional feedback controller. The neural network training process is carried out by using two different techniques: backpropagation and extended Kalman filter algorithm. Additionally, the conver...

Enhanced motor learning with bilateral transcranial direct current stimulation: Impact of polarity or current flow direction?

Science.gov (United States)

Naros, Georgios; Geyer, Marc; Koch, Susanne; Mayr, Lena; Ellinger, Tabea; Grimm, Florian; Gharabaghi, Alireza

2016-04-01

Bilateral transcranial direct current stimulation (TDCS) is superior to unilateral TDCS when targeting motor learning. This effect could be related to either the current flow direction or additive polarity-specific effects on each hemisphere. This sham-controlled randomized study included fifty right-handed healthy subjects in a parallel-group design who performed an exoskeleton-based motor task of the proximal left arm on three consecutive days. Prior to training, we applied either sham, right anodal (a-TDCS), left cathodal (c-TDCS), concurrent a-TDCS and c-TDCS with two independent current sources and return electrodes (double source (ds)-TDCS) or classical bilateral stimulation (bi-TDCS). Motor performance improved over time for both unilateral (a-TDCS, c-TDCS) and bilateral (bi-TDCS, ds-TDCS) TDCS montages. However, only the two bilateral paradigms led to an improvement of the final motor performance at the end of the training period as compared to the sham condition. There was no difference between the two bilateral stimulation conditions (bi-TDCS, ds-TDCS). Bilateral TDCS is more effective than unilateral stimulation due to its polarity-specific effects on each hemisphere rather than due to its current flow direction. This study is the first systematic evaluation of stimulation polarity and current flow direction of bi-hemispheric motor cortex TDCS on motor learning of proximal upper limb muscles. Copyright © 2016 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

Increasing of visibility on the pedestrian crossing by the additional lighting systems

Science.gov (United States)

Baleja, Richard; Bos, Petr; Novak, Tomas; Sokansky, Karel; Hanusek, Tomas

2017-09-01

Pedestrian crossings are critical places for road accidents between pedestrians and motor vehicles. For this reason, it is very important to increase attention when the pedestrian crossings are designed and it is necessary to take into account all factors that may contribute to higher safety. Additional lighting systems for pedestrian crossings are one of them and the lighting systems must fulfil the requirements for higher visibility from the point of view of car drivers from both directions. This paper describes the criteria for the suitable additional lighting system on pedestrian crossings. Generally, it means vertical illuminance on the pedestrian crossing from the driver’s view, horizontal illuminance on the crossing and horizontal illuminance both in front of and behind the crossing placed on the road and their acceptable ratios. The article also describes the choice of the colours of the light (correlated colour temperature) and its influence on visibility. As a part of the article, there are case designs of additional lighting systems for pedestrian crossings and measurements from realized additional lighting systems by luxmeters and luminance cameras and their evaluation.

Additive manufacturing technology (direct metal laser sintering) as a novel approach to fabricate functionally graded titanium implants: preliminary investigation of fabrication parameters.

Science.gov (United States)

Lin, Wei-Shao; Starr, Thomas L; Harris, Bryan T; Zandinejad, Amirali; Morton, Dean

2013-01-01

This article describes the preliminary findings of the mechanical properties of functionally graded titanium with controlled distribution of porosity and a reduced Young's modulus on the basis of a computeraided design (CAD) file, using the rapid-prototyping, direct metal laser sintering (DMLS) technique. Sixty specimens of Ti-6Al-4V were created using a DMLS machine (M270) following the standard for tensile testing of metals. One group was fabricated with only 170 W of laser energy to create fully dense specimens (control group). The remaining specimens all featured an outer fully dense "skin" layer and a partially sintered porous inner "core" region. The outer "skin" of each specimen was scanned at 170 W and set at a thickness of 0.35, 1.00, or 1.50 mm for different specimen groups. The inner "core" of each specimen was scanned at a lower laser power (43 or 85 W). The partially sintered core was clearly visible in all specimens, with somewhat greater porosity with the lower laser power. However, the amount of porosity in the core region was not related to the laser power alone; thinner skin layers resulted in higher porosity for the same power values in the core structure. The lowest Young's modulus achieved, 35 GPa, is close to that of bone and was achieved with a laser power of 43 W and a skin thickness of 0.35 mm, producing a core that comprised 74% of the total volume. Additive manufacturing technology may provide an efficient alternative way to fabricate customized dental implants based on a CAD file with a functionally graded structure that may minimize stress shielding and improve the long-term performance of dental implants.

Influence of additive laser manufacturing parameters on surface using density of partially melted particles

Science.gov (United States)

Rosa, Benoit; Brient, Antoine; Samper, Serge; Hascoët, Jean-Yves

2016-12-01

Mastering the additive laser manufacturing surface is a real challenge and would allow functional surfaces to be obtained without finishing. Direct Metal Deposition (DMD) surfaces are composed by directional and chaotic textures that are directly linked to the process principles. The aim of this work is to obtain surface topographies by mastering the operating process parameters. Based on experimental investigation, the influence of operating parameters on the surface finish has been modeled. Topography parameters and multi-scale analysis have been used in order to characterize the DMD obtained surfaces. This study also proposes a methodology to characterize DMD chaotic texture through topography filtering and 3D image treatment. In parallel, a new parameter is proposed: density of particles (D p). Finally, this study proposes a regression modeling between process parameters and density of particles parameter.

Direct production of high pt leptons and search for additional heavy bosons at 1.8 TeV

International Nuclear Information System (INIS)

Gold, M.

1991-10-01

We have studied the production of high p t electrons and muons and searched for additional heavy charged (W') and neutral (Z') vector bosons. We find no evidence for such bosons and set limits of M w ' > 520 GeV and M Z ' > 412 GeV (95% confidence level) assuming Standard Model couplings. The production of high mass electron and muon pairs is consistent with the Standard Model prediction for the Drell-Yan production mechanism. Lower limits of 2.2 TeV and 1.6 TeV (95% confidence level) are set on electron-quark and muon-quark compositeness scale parameters Λ LL - associated with an effective contact interaction

Feature based Weld-Deposition for Additive Manufacturing of Complex Shapes

Science.gov (United States)

Panchagnula, Jayaprakash Sharma; Simhambhatla, Suryakumar

2018-06-01

Fabricating functional metal parts using Additive Manufacturing (AM) is a leading trend. However, realizing overhanging features has been a challenge due to the lack of support mechanism for metals. Powder-bed fusion techniques like, Selective Laser Sintering (SLS) employ easily-breakable-scaffolds made of the same material to realize the overhangs. However, the same approach is not extendible to deposition processes like laser or arc based direct energy deposition processes. Although it is possible to realize small overhangs by exploiting the inherent overhanging capability of the process or by blinding some small features like holes, the same cannot be extended for more complex geometries. The current work presents a novel approach for realizing complex overhanging features without the need of support structures. This is possible by using higher order kinematics and suitably aligning the overhang with the deposition direction. Feature based non-uniform slicing and non-uniform area-filling are some vital concepts required in realizing the same and are briefly discussed here. This method can be used to fabricate and/or repair fully dense and functional components for various engineering applications. Although this approach has been implemented for weld-deposition based system, the same can be extended to any other direct energy deposition processes also.

Short-term salivary acetaldehyde increase due to direct exposure to alcoholic beverages as an additional cancer risk factor beyond ethanol metabolism

Directory of Open Access Journals (Sweden)

Monakhova Yulia B

2011-01-01

Full Text Available Abstract Background An increasing body of evidence now implicates acetaldehyde as a major underlying factor for the carcinogenicity of alcoholic beverages and especially for oesophageal and oral cancer. Acetaldehyde associated with alcohol consumption is regarded as 'carcinogenic to humans' (IARC Group 1, with sufficient evidence available for the oesophagus, head and neck as sites of carcinogenicity. At present, research into the mechanistic aspects of acetaldehyde-related oral cancer has been focused on salivary acetaldehyde that is formed either from ethanol metabolism in the epithelia or from microbial oxidation of ethanol by the oral microflora. This study was conducted to evaluate the role of the acetaldehyde that is found as a component of alcoholic beverages as an additional factor in the aetiology of oral cancer. Methods Salivary acetaldehyde levels were determined in the context of sensory analysis of different alcoholic beverages (beer, cider, wine, sherry, vodka, calvados, grape marc spirit, tequila, cherry spirit, without swallowing, to exclude systemic ethanol metabolism. Results The rinsing of the mouth for 30 seconds with an alcoholic beverage is able to increase salivary acetaldehyde above levels previously judged to be carcinogenic in vitro, with levels up to 1000 μM in cases of beverages with extreme acetaldehyde content. In general, the highest salivary acetaldehyde concentration was found in all cases in the saliva 30 sec after using the beverages (average 353 μM. The average concentration then decreased at the 2-min (156 μM, 5-min (76 μM and 10-min (40 μM sampling points. The salivary acetaldehyde concentration depends primarily on the direct ingestion of acetaldehyde contained in the beverages at the 30-sec sampling, while the influence of the metabolic formation from ethanol becomes the major factor at the 2-min sampling point. Conclusions This study offers a plausible mechanism to explain the increased risk for oral

Additive Design and Manufacturing of Jet Engine Parts

Directory of Open Access Journals (Sweden)

Pinlian Han

2017-10-01

Full Text Available The additive design (AD and additive manufacturing (AM of jet engine parts will revolutionize the traditional aerospace industry. The unique characteristics of AM, such as gradient materials and micro-structures, have opened up a new direction in jet engine design and manufacturing. Engineers have been liberated from many constraints associated with traditional methodologies and technologies. One of the most significant features of the AM process is that it can ensure the consistency of parts because it starts from point(s, continues to line(s and layer(s, and ends with the competed part. Collaboration between design and manufacturing is the key to success in fields including aerodynamics, thermodynamics, structural integration, heat transfer, material development, and machining. Engineers must change the way they design a part, as they shift from the traditional method of “subtracting material” to the new method of “adding material” in order to manufacture a part. AD is not the same as designing for AM. A new method and new tools are required to assist with this new way of designing and manufacturing. This paper discusses in detail what is required in AD and AM, and how current problems can be solved.

Bioinspired synthesis of pentalene-based chromophores from an oligoketone chain.

Science.gov (United States)

Saito, Yuki; Higuchi, Masayuki; Yoshioka, Shota; Senboku, Hisanori; Inokuma, Yasuhide

2018-04-24

We report a bioinspired synthesis of 2,5-dihydropentalene-based chromophores from an aliphatic oligoketone bearing 1,3- and 1,4-diketone subunits. Unlike the natural polyketone sequence, fused five-membered rings were formed via an intramolecular aldol condensation. A subsequent Knoevenagel condensation reaction with malononitrile furnished a multiply cross-conjugated π-system with low-lying LUMO levels. Furthermore, pentalenes obtained from a non-conjugated aliphatic chain exhibited visible absorption and solid-state fluorescence.

Design Preliminaries for Direct Drive under Water Wind Turbine Generator

DEFF Research Database (Denmark)

Leban, Krisztina Monika; Ritchie, Ewen; Argeseanu, Alin

2012-01-01

This paper focuses on the preliminary design process of a 20 MW electric generator. The application calls for an offshore, vertical axis, direct drive wind turbine. Arguments for selecting the type of electric machine for the application are presented and discussed. Comparison criteria for deciding...... on a type of machine are listed. Additional constraints emerging from the direct drive, vertical axis concepts are considered. General rules and a preliminary algorithm are discussed for the machine selected to be most suitable for the imposed conditions....

Novel robotic systems and future directions

Directory of Open Access Journals (Sweden)

Ki Don Chang

2018-01-01

Full Text Available Robot-assistance is increasingly used in surgical practice. We performed a nonsystematic literature review using PubMed/MEDLINE and Google for robotic surgical systems and compiled information on their current status. We also used this information to predict future about the direction of robotic systems based on various robotic systems currently being developed. Currently, various modifications are being made in the consoles, robotic arms, cameras, handles and instruments, and other specific functions (haptic feedback and eye tracking that make up the robotic surgery system. In addition, research for automated surgery is actively being carried out. The development of future robots will be directed to decrease the number of incisions and improve precision. With the advent of artificial intelligence, a more practical form of robotic surgery system can be introduced and will ultimately lead to the development of automated robotic surgery system.

Incommensurate crystallography without additional dimensions.

Science.gov (United States)

Kocian, Philippe

2013-07-01

It is shown that the Euclidean group of translations, when treated as a Lie group, generates translations not only in Euclidean space but on any space, curved or not. Translations are then not necessarily vectors (straight lines); they can be any curve compatible with the parameterization of the considered space. In particular, attention is drawn to the fact that one and only one finite and free module of the Lie algebra of the group of translations can generate both modulated and non-modulated lattices, the modulated character being given only by the parameterization of the space in which the lattice is generated. Moreover, it is shown that the diffraction pattern of a structure is directly linked to the action of that free and finite module. In the Fourier transform of a whole structure, the Fourier transform of the electron density of one unit cell (i.e. the structure factor) appears concretely, whether the structure is modulated or not. Thus, there exists a neat separation: the geometrical aspect on the one hand and the action of the group on the other, without requiring additional dimensions.

Children’s Non-symbolic, Symbolic Addition and Their Mapping Capacity at 4–7 Years Old

Directory of Open Access Journals (Sweden)

Yanjun Li

2017-07-01

Full Text Available The study aimed to examine the developmental trajectories of non-symbolic and symbolic addition capacities in children and the mapping ability between these two. We assessed 106 4- to 7-year-old children and found that 4-year-olds were able to do non-symbolic addition but not symbolic addition. Five-year-olds and older were able to do symbolic addition and their performance in symbolic addition exceeded non-symbolic addition in grade 1 (approximate age 7. These results suggested non-symbolic addition ability emerges earlier and is less affected by formal mathematical education than symbolic addition. Meanwhile, we tested children’s bi-directional mapping ability using a novel task and found that children were able to map between symbolic and non-symbolic representations of number at age 5. Their ability in mapping non-symbolic to symbolic number became more proficient in grade 1 (approximate age 7. This suggests children at age 7 have developed a relatively mature symbolic representation system.

Working memory capacity predicts listwise directed forgetting in adults and children.

Science.gov (United States)

Aslan, Alp; Zellner, Martina; Bäuml, Karl-Heinz T

2010-05-01

In listwise directed forgetting, participants are cued to forget previously studied material and to learn new material instead. Such cueing typically leads to forgetting of the first set of material and to memory enhancement of the second. The present study examined the role of working memory capacity in adults' and children's listwise directed forgetting. Working memory capacity was assessed with complex span tasks. In Experiment 1 working memory capacity predicted young adults' directed-forgetting performance, demonstrating a positive relationship between working memory capacity and each of the two directed-forgetting effects. In Experiment 2 we replicated the finding with a sample of first and a sample of fourth-grade children, and additionally showed that working memory capacity can account for age-related increases in directed-forgetting efficiency between the two age groups. Following the view that directed forgetting is mediated by inhibition of the first encoded list, the results support the proposal of a close link between working memory capacity and inhibitory function.

75 FR 76630 - Direct Investment Surveys: BE-577, Quarterly Survey of U.S. Direct Investment Abroad-Direct...

Science.gov (United States)

2010-12-09

....S. Direct Investment Abroad--Direct Transactions of U.S. Reporter With Foreign Affiliate.'' The..., Quarterly Survey of U.S. Direct Investment Abroad--Direct Transactions of U.S. Reporter With Foreign...] RIN 0691--AA75 Direct Investment Surveys: BE-577, Quarterly Survey of U.S. Direct Investment Abroad...

Optimal directional view angles for remote-sensing missions

Science.gov (United States)

Kimes, D. S.; Holben, B. N.; Tucker, C. J.; Newcomb, W. W.

1984-01-01

The present investigation is concerned with the directional, off-nadir viewing of terrestrial scenes using remote-sensing systems from aircraft and satellite platforms, taking into account advantages of such an approach over strictly nadir viewing systems. Directional reflectance data collected for bare soil and several different vegetation canopies in NOAA-7 AVHRR bands 1 and 2 were analyzed. Optimum view angles were recommended for two strategies. The first strategy views the utility of off-nadir measurements as extending spatial and temporal coverage of the target area. The second strategy views the utility of off-nadir measurements as providing additional information about the physical characteristics of the target. Conclusions regarding the two strategies are discussed.

Comparison between direct transesterification of microalgae and hydrochar

Directory of Open Access Journals (Sweden)

Vo Thanh Phuoc

2017-07-01

Full Text Available Hydrothermal carbonization (HTC of microalgae is one of processes that can effectively remove moisture from microalgae. In addition, the hydrochar retains most of fatty acids from microalgae feedstock, and the content of fatty acids in hydrochar is doubled. This research concentrates on the comparison between direct transesterification of microalgae and hydrochar. The result shows that the biodiesel yields of hydrochar were higher than those of microalgae at the same reaction conditions due to the higher extraction rate of fatty acids from hydrochar. Finally, the amount of methanol and catalyst which is required for a given amount of microalgae can be reduced to a half through the direct transesterification of hydrochar.

Mucus: An Underestimated Gut Target for Environmental Pollutants and Food Additives.

Science.gov (United States)

Gillois, Kévin; Lévêque, Mathilde; Théodorou, Vassilia; Robert, Hervé; Mercier-Bonin, Muriel

2018-06-15

Synthetic chemicals (environmental pollutants, food additives) are widely used for many industrial purposes and consumer-related applications, which implies, through manufactured products, diet, and environment, a repeated exposure of the general population with growing concern regarding health disorders. The gastrointestinal tract is the first physical and biological barrier against these compounds, and thus their first target. Mounting evidence indicates that the gut microbiota represents a major player in the toxicity of environmental pollutants and food additives; however, little is known on the toxicological relevance of the mucus/pollutant interplay, even though mucus is increasingly recognized as essential in gut homeostasis. Here, we aimed at describing how environmental pollutants (heavy metals, pesticides, and other persistent organic pollutants) and food additives (emulsifiers, nanomaterials) might interact with mucus and mucus-related microbial species; that is, “mucophilic” bacteria such as mucus degraders. This review highlights that intestinal mucus, either directly or through its crosstalk with the gut microbiota, is a key, yet underestimated gut player that must be considered for better risk assessment and management of environmental pollution.

Revised Mechanism and Improved Efficiency of the QuikChange Site-Directed Mutagenesis Method.

Science.gov (United States)

Xia, Yongzhen; Xun, Luying

2017-01-01

Site-directed mutagenesis has been widely used for the substitution, addition or deletion of nucleotide residues in a defined DNA sequence. QuikChange™ site-directed mutagenesis and its related protocols have been widely used for this purpose because of convenience and efficiency. We have recently demonstrated that the mechanism of the QuikChange™ site-directed mutagenesis process is different from that being proposed. The new mechanism promotes the use of partially overlapping primers and commercial PCR enzymes for efficient PCR and mutagenesis.

Additivity of Pyrethroid Actions on Sodium Influx in Cortical Neurons in Cerebrocortical Neurons in Primary Culture

Science.gov (United States)

BACKGROUND: Pyrethroid insecticides bind to voltage-gated sodium channels and modify their gating kinetics, thereby disrupting neuronal function. Although previous work has tested the additivity of pyrethroids in vivo, this has not been assessed directly at the primary molecular ...

Magnetostrictive performance of additively manufactured CoFe rods using the LENSTM system

Science.gov (United States)

Jones, Nicholas J.; Yoo, Jin-Hyeong; Ott, Ryan T.; Lambert, Paul K.; Petculescu, Gabriela; Simsek, Emrah; Schlagel, Deborah; Lograsso, Thomas A.

2018-05-01

Magnetostrictive materials exhibit a strain in the presence of a variable magnetic field. While they normally require large, highly oriented crystallographic grains for high strain values, metal additive manufacturing (3D printing) may be able to produce highly textured polycrystalline rods, with properties comparable to those manufactured using the more demanding free standing zone melting (FSZM) technique. Rods of Co75.8Fe24.2 and Co63.7Fe36.3 have been fabricated using the Laser engineered net shaping (LENSTM) system to evaluate the performance of additively manufactured magnetic and magnetostrictive materials. The 76% Co sample showed an average magnetostriction (λ) of 86 ppm at a stress of 124 MPa; in contrast, the 64% Co sample showed only 27 ppm at the same stress. For direct comparison, a Co67Fe33 single crystal disk, also measured as part of this study, exhibited a magnetostriction value of 131 and 91 microstrain in the [100] and [111] directions, respectively, with a calculated polycrystalline value (λs) of 107 microstrain. Electron back scattered diffraction (EBSD) has been used to qualitatively link the performance with crystallographic orientation and phase information, showing only the BCC phase in the 76% Co sample, but three different phases (BCC, FCC, and HCP) in the 64% Co sample.

Magnetostrictive performance of additively manufactured CoFe rods using the LENSTM system

Directory of Open Access Journals (Sweden)

Nicholas J. Jones

2018-05-01

Full Text Available Magnetostrictive materials exhibit a strain in the presence of a variable magnetic field. While they normally require large, highly oriented crystallographic grains for high strain values, metal additive manufacturing (3D printing may be able to produce highly textured polycrystalline rods, with properties comparable to those manufactured using the more demanding free standing zone melting (FSZM technique. Rods of Co75.8Fe24.2 and Co63.7Fe36.3 have been fabricated using the Laser engineered net shaping (LENSTM system to evaluate the performance of additively manufactured magnetic and magnetostrictive materials. The 76% Co sample showed an average magnetostriction (λ of 86 ppm at a stress of 124 MPa; in contrast, the 64% Co sample showed only 27 ppm at the same stress. For direct comparison, a Co67Fe33 single crystal disk, also measured as part of this study, exhibited a magnetostriction value of 131 and 91 microstrain in the [100] and [111] directions, respectively, with a calculated polycrystalline value (λs of 107 microstrain. Electron back scattered diffraction (EBSD has been used to qualitatively link the performance with crystallographic orientation and phase information, showing only the BCC phase in the 76% Co sample, but three different phases (BCC, FCC, and HCP in the 64% Co sample.

Design, Development and Hotfire Testing of Monolithic Copper and Bimetallic Additively Manufactured Combustion Chambers

Science.gov (United States)

Gradl, Paul; Barnett, Greg; Brandsmeier, Will; Greene, Sandy Elam; Protz, Chris

2016-01-01

NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM) otherwise commonly referred to as additive manufacturing. The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for the GRCop-84 copper-alloy commensurate with powder bed additive manufacturing, evaluate bimetallic deposition and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. As a direct spin off of this program, NASA is working with industry partners to further develop the printing process for the GRCop-84 material in addition to the C-18150 (CuCrZr) material. To advance the process further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic additively manufactured chambers. A 1.2k sized thrust-chamber was designed and developed to compare the printing process of the GRCop-84 and C-18150 SLM materials. A series of similar MCC liners also completed development with an Inconel 625 jacket bonded to the GRcop-84 liner evaluating direct metal deposition (DMD) laser and arc-based techniques. This paper describes the design, development, manufacturing and testing of these combustion chambers and associated lessons learned throughout the design and development process.

Direct photon production and jet energy-loss in small systems

Energy Technology Data Exchange (ETDEWEB)

Shen, Chun; Park, Chanwook [Department of Physics, McGill University, 3600 University Street, Montreal, QC, H3A 2T8 (Canada); Paquet, Jean-François [Department of Physics, McGill University, 3600 University Street, Montreal, QC, H3A 2T8 (Canada); Department of Physics & Astronomy, Stony Brook University, Stony Brook, NY 11733 (United States); Denicol, Gabriel S. [Department of Physics, McGill University, 3600 University Street, Montreal, QC, H3A 2T8 (Canada); Physics Department, Brookhaven National Laboratory, Upton, NY 11973 (United States); Jeon, Sangyong; Gale, Charles [Department of Physics, McGill University, 3600 University Street, Montreal, QC, H3A 2T8 (Canada)

2016-12-15

Two types of penetrating probes, direct photon and QCD jets, are investigated in the background of a small and rapidly expanding droplet of quark-gluon plasma. The additional thermal electromagnetic radiation results in a ∼50% enhancement of the direct photons. In high multiplicity p+Pb collisions, jets can lose a sizeable fraction of their initial energy, leading to a charged hadron R{sub pA} of ∼0.8 at a transverse momentum around 10 GeV. Those two proposed measurements can help understand the apparent collective behaviour observed in small collision systems.

Toward Additive-Free Small-Molecule Organic Solar Cells: Roles of the Donor Crystallization Pathway and Dynamics

KAUST Repository

Abdelsamie, Maged; Treat, Neil D.; Zhao, Kui; McDowell, Caitlin; Burgers, Mark A.; Li, Ruipeng; Smilgies, Detlef M.; Stingelin, Natalie; Bazan, Guillermo C.; Amassian, Aram

2015-01-01

processing to promote crystallization, phase separation, and efficient light harvesting. A donor material (X2) that crystallizes directly from solution yields additive-free solar cells with an efficiency of 7.6%. © 2015 WILEY-VCH Verlag GmbH & Co. KGa

Directing the public to evidence-based online content.

Science.gov (United States)

Cooper, Crystale Purvis; Gelb, Cynthia A; Vaughn, Alexandra N; Smuland, Jenny; Hughes, Alexandra G; Hawkins, Nikki A

2015-04-01

To direct online users searching for gynecologic cancer information to accurate content, the Centers for Disease Control and Prevention's (CDC) 'Inside Knowledge: Get the Facts About Gynecologic Cancer' campaign sponsored search engine advertisements in English and Spanish. From June 2012 to August 2013, advertisements appeared when US Google users entered search terms related to gynecologic cancer. Users who clicked on the advertisements were directed to relevant content on the CDC website. Compared with the 3 months before the initiative (March-May 2012), visits to the CDC web pages linked to the advertisements were 26 times higher after the initiative began (June-August 2012) (padvertisements were supplemented with promotion on television and additional websites (September 2012-August 2013) (padvertisements can direct users to evidence-based content at a highly teachable moment--when they are seeking relevant information. © The Author 2014. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Direct uptake and degradation of DNA by lysosomes

Science.gov (United States)

Fujiwara, Yuuki; Kikuchi, Hisae; Aizawa, Shu; Furuta, Akiko; Hatanaka, Yusuke; Konya, Chiho; Uchida, Kenko; Wada, Keiji; Kabuta, Tomohiro

2013-01-01

Lysosomes contain various hydrolases that can degrade proteins, lipids, nucleic acids and carbohydrates. We recently discovered “RNautophagy,” an autophagic pathway in which RNA is directly taken up by lysosomes and degraded. A lysosomal membrane protein, LAMP2C, a splice variant of LAMP2, binds to RNA and acts as a receptor for this pathway. In the present study, we show that DNA is also directly taken up by lysosomes and degraded. Like RNautophagy, this autophagic pathway, which we term “DNautophagy,” is dependent on ATP. The cytosolic sequence of LAMP2C also directly interacts with DNA, and LAMP2C functions as a receptor for DNautophagy, in addition to RNautophagy. Similarly to RNA, DNA binds to the cytosolic sequences of fly and nematode LAMP orthologs. Together with the findings of our previous study, our present findings suggest that RNautophagy and DNautophagy are evolutionarily conserved systems in Metazoa. PMID:23839276

Photoelectrochemical based direct conversion systems for hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Kocha, S.; Peterson, M.; Arent, D. [National Renewable Energy Lab., Golden, CO (United States)] [and others

1996-10-01

Photon driven, direct conversion systems consist of a light absorber and a water splitting catalyst as a monolithic system; water is split directly upon illumination. This one-step process eliminates the need to generate electricity externally and subsequently feed it to an electrolyzer. These configurations require only the piping necessary for transport of hydrogen to an external storage system or gas pipeline. This work is focused on multiphoton photoelectrochemical devices for production of hydrogen directly using sunlight and water. Two types of multijunction cells, one consisting of a-Si triple junctions and the other GaInP{sub 2}/GaAs homojunctions, were studied for the photoelectrochemical decomposition of water into hydrogen and oxygen from an aqueous electrolyte solution. To catalyze the water decomposition process, the illuminated surface of the device was modified either by addition of platinum colloids or by coating with ruthenium dioxide. These colloids have been characterized by gel electrophoresis.

Ontogeny of additive and maternal genetic effects: lessons from domestic mammals.

Science.gov (United States)

Wilson, Alastair J; Reale, Denis

2006-01-01

Evolution of size and growth depends on heritable variation arising from additive and maternal genetic effects. Levels of heritable (and nonheritable) variation might change over ontogeny, increasing through "variance compounding" or decreasing through "compensatory growth." We test for these processes using a meta-analysis of age-specific weight traits in domestic ungulates. Generally, mean standardized variance components decrease with age, consistent with compensatory growth. Phenotypic convergence among adult sheep occurs through decreasing environmental and maternal genetic variation. Maternal variation similarly declines in cattle. Maternal genetic effects are thus reduced with age (both in absolute and relative terms). Significant trends in heritability (decreasing in cattle, increasing in sheep) result from declining maternal and environmental components rather than from changing additive variation. There was no evidence for increasing standardized variance components. Any compounding must therefore be masked by more important compensatory processes. While extrapolation of these patterns to processes in natural population is difficult, our results highlight the inadequacy of assuming constancy in genetic parameters over ontogeny. Negative covariance between direct and maternal genetic effects was common. Negative correlations with additive and maternal genetic variances indicate that antagonistic pleiotropy (between additive and maternal genetic effects) may maintain genetic variance and limit responses to selection.

Friction-induced nano-structural evolution of graphene as a lubrication additive

Science.gov (United States)

Zhao, Jun; Mao, Junyuan; Li, Yingru; He, Yongyong; Luo, Jianbin

2018-03-01

Graphene has attracted enormous attention in the field of lubrication based on its excellent physical and chemical properties. Although many studies have obtained thermally or chemically- exfoliated graphene and investigated their wide and important application, few studies have reported their physical nano-structural evolution under friction. In this study, we investigated the lubrication properties of graphene additives with different layer numbers and interlayer spacing by exfoliating. The additives with a higher degrees of exfoliation changed to ordering under friction, and had better lubrication properties, while that with a lower degrees exhibited obvious structural defects and high friction. Therefore, the original degrees of exfoliation plays a key role in the structural evolution of graphene and superior lubrication can be achieved through the physical nano-structure changing to ordering, even graphitization. Furthermore, the ordered tribofilm on the frictional interfaces was parallel to the sliding direction, meaning the highly exfoliated graphene indeed reaching slippage between its layers, which wasn't experimentally discovered in previous studies. This work provides a new understanding of the relationship between friction-induced nano-structural evolution and lubrication properties of graphene as a lubrication additive, and has great potential for the structural design of graphene as a lubrication additive.

Report From BPTCS Project Team On Evaluation Of Additive Manufacturing For Pressure Retaining Equipment

Energy Technology Data Exchange (ETDEWEB)

Rawls, G. [Savannah River Site (SRS), Aiken, SC (United States)

2016-09-22

ASME is evaluating the use of additive manufacturing (AM) for the construction of pressure equipment. The information in this report assesses available AM technologies for direct metal fabrication of pressure equipment. Background information is included in the report to provide context for those not experienced in AM technology. Only commercially available technologies for direct metal fabrication are addressed in the report because these AM methods are the only viable approaches for the construction of pressure equipment. Metal AM technologies can produce near-net shape parts by using multiple layers of material from a three dimensional (3D) design model of the geometry. Additive manufacturing of metal components was developed from polymer based rapid prototyping or 3D printing. At the current maturity level, AM application for pressure equipment has the potential to reduce delivery times and costs for complex shapes. AM will also lead to a reduction in the use of high cost materials, since parts can be created with corrosion resistant layers of high alloy material and structural layers of lower cost materials.

Mechanical and Fatigue Properties of Additively Manufactured Metallic Materials

Science.gov (United States)

Yadollahi, Aref

This study aims to investigate the mechanical and fatigue behavior of additively manufactured metallic materials. Several challenges associated with different metal additive manufacturing (AM) techniques (i.e. laser-powder bed fusion and direct laser deposition) have been addressed experimentally and numerically. Experiments have been carried out to study the effects of process inter-layer time interval--i.e. either building the samples one-at-a-time or multi-at-a-time (in-parallel)--on the microstructural features and mechanical properties of 316L stainless steel samples, fabricated via a direct laser deposition (DLD). Next, the effect of building orientation--i.e. the orientation in which AM parts are built--on microstructure, tensile, and fatigue behaviors of 17-4 PH stainless steel, fabricated via a laser-powder bed fusion (L-PBF) method was investigated. Afterwards, the effect of surface finishing--here, as-built versus machined--on uniaxial fatigue behavior and failure mechanisms of Inconel 718 fabricated via a laser-powder bed fusion technique was sought. The numerical studies, as part of this dissertation, aimed to model the mechanical behavior of AM materials, under monotonic and cyclic loading, based on the observations and findings from the experiments. Despite significant research efforts for optimizing process parameters, achieving a homogenous, defect-free AM product--immediately after fabrication--has not yet been fully demonstrated. Thus, one solution for ensuring the adoption of AM materials for application should center on predicting the variations in mechanical behavior of AM parts based on their resultant microstructure. In this regard, an internal state variable (ISV) plasticity-damage model was employed to quantify the damage evolution in DLD 316L SS, under tensile loading, using the microstructural features associated with the manufacturing process. Finally, fatigue behavior of AM parts has been modeled based on the crack-growth concept

Identification of flavour additives in tobacco products to develop a flavour library

Science.gov (United States)

Krüsemann, Erna JZ; Visser, Wouter F; Cremers, Johannes WJM; Pennings, Jeroen LA; Talhout, Reinskje

2018-01-01

Objectives This study combines chemical analysis and flavour descriptions of flavour additives used in tobacco products, and provides a starting point to build an extensive library of flavour components, useful for product surveillance. Methods Headspace gas chromatography-mass spectrometry (GC-MS) was used to compare 22 commercially available tobacco products (cigarettes and roll-your-own) expected to have a characterising flavour and 6 commercially available products not expected to have a characterising flavour with 5 reference products (natural tobacco leaves and research cigarettes containing no flavour additives). The flavour components naturally present in the reference products were excluded from components present in commercially available products containing flavour additives. A description of the remaining flavour additives was used for categorisation. Results GC-MS measurements of the 33 tobacco products resulted in an overview of 186 chemical compounds. Of these, 144 were solely present in commercially available products. These 144 flavour additives were described using 62 different flavour descriptors extracted from flavour databases, which were categorised into eight groups largely based on the definition of characterising flavours from the European Tobacco Product Directive: fruit, spice, herb, alcohol, menthol, sweet, floral and miscellaneous. Conclusions We developed a method to identify and describe flavour additives in tobacco products. Flavour additives consist of single flavour compounds or mixtures of multiple flavour compounds, and different combinations of flavour compounds can cause a certain flavour. A flavour library helps to detect flavour additives that are characteristic for a certain flavour, and thus can be useful for regulation of flavours in tobacco and related products. PMID:28190004

[Food additives and healthiness].

Science.gov (United States)

Heinonen, Marina

2014-01-01

Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects.

Reactivity descriptors for direct methanol fuel cell anode catalysts

DEFF Research Database (Denmark)

Ferrin, Peter; Nilekar, Anand Udaykumar; Greeley, Jeff

2008-01-01

oxidation to CO2 are investigated: an indirect mechanism that goes through a CO intermediate and a direct mechanism where methanol is oxidized to CO2 without the formation of a CO intermediate. For the direct mechanism, we find that, because of CO poisoning, only a small current will result on all non......We have investigated the anode reaction in direct methanol fuel cells using a database of adsorption free energies for 16 intermediates on 12 close-packed transition metal surfaces calculated with periodic, self-consistent, density functional theory (DFT-GGA). This database, combined with a simple...... electrokinetic model of the methanol electrooxidation reaction, yields mechanistic insights that are consistent with previous experimental and theoretical studies on Pt, and extends these insights to a broad spectrum of other transition metals. In addition, by using linear scaling relations between...

Direct metal brazing to cermet feedthroughs

International Nuclear Information System (INIS)

Hopper, A.C. Jr.

1984-01-01

An improved method for brazing metallic components to a cermet surface in an alumina substrate eliminates the prior art metallized layer over the cermet via and adjoining alumina surfaces. Instead, a nickel layer is applied over the cermet surface only and metallic components are brazed directly to this nickel coated cermet surface. As a result, heretofore unachievable tensile strength joints are produced. In addition, cermet vias with their brazed metal components can be spaced more closely in the alumina substrate because of the elimination of the prior art metallized alumina surfaces

Polar-Direct-Drive Experiments on OMEGA

International Nuclear Information System (INIS)

Marshall, F.J.; Craxton, R.S.; Bonino, M.J.; Epstein, R.; Glebov, V.Yu.; Jacobs-Perkins, D.; Knauer, J.P.; Marozas, J.A.; McKenty, P.W.; Noyes, S.G.; Radha, P.B.; Seka, W.; Skupsky, S.; Smalyuk

2006-01-01

Polar direct drive (PDD), a promising ignition path for the NIF while the beams are in the indirect-drive configuration, is currently being investigated on the OMEGA laser system by using 40 beams in six rings repointed to more uniformly illuminate the target. The OMEGA experiments are being performed with standard, ''warm'' targets with and without the use of an equatorial ''Saturn-like'' toroidally shaped CH ring. Target implosion symmetry is diagnosed with framed x-ray backlighting using additional OMEGA beams and by time-integrated x-ray imaging of the stagnating core

Development of Direct-Use Projects: Preprint

Energy Technology Data Exchange (ETDEWEB)

Lund, J.

2011-01-01

A geothermal direct-use project utilizes a natural resource, a flow of geothermal fluid at elevated temperatures, which is capable of providing heat and/or cooling to buildings, greenhouses, aquaculture ponds, and industrial processes. Geothermal utilization requires matching the varied needs of the user and characteristics of the resource in order to development a successful project. Each application is unique; guidelines are provided for the logical steps required to implement a project. Recommended temperature and flows are suggested for spas and pools, space and district heating, greenhouse and aquaculture pond heating, and industrial applications. Guidelines are provided for selecting the necessary equipment for successfully implementing a direct-use project, including downhole pumps, piping, heat exchangers, and heat convectors. Additionally, the relationship between temperature, flow rate, and the use of heat exchangers to provide heat to a space with hot water or hot air is provided for a number of applications, with suggested 'rules of thumb'.

Direct utilization of geothermal energy

International Nuclear Information System (INIS)

Lund, J. W.

2010-01-01

The worldwide application of geothermal energy for direct utilization is reviewed. This paper is based on the world update for direct-use presented at the World Geothermal Congress 2010 in Bali, Indonesia (WGC2010) which also includes material presented at three world geothermal congresses in Italy, Japan and Turkey (WGC95, WGC2000 and WGC2005). This report is based on country update papers prepared for WGC2010 and data from other sources. Final update papers were received from 70 countries of which 66 reported some direct utilization of geothermal energy for WGC2010. Twelve additional countries were added to the list based on other sources of information. The 78 countries having direct utilization of geothermal energy, is a significant increase from the 72 reported in 2005, the 58 reported in 2000, and the 28 reported in 1995. An estimate of the installed thermal power for direct utilization at the end of 2009, reported from WGC2010 is 48,493 MW th , almost a 72 % increased over the 2005 data, growing at a compound rate of 11.4% annually with a capacity factor of 0.28. The thermal energy used is 423,830 TJ/year (117,740 GWh/yr), about a 55% increase over 2005, growing at a compound rate of 9.2% annually. The distribution of thermal energy used by category is approximately 47.2% for ground-source heat pumps, 25.8% for bathing and swimming (including balneology), 14.9% for space heating (of which 85% is for district heating), 5.5% for greenhouses and open ground heating, 2.8% for industrial process heating, 2.7% for aquaculture pond and raceway heating, 0.4% for agricultural drying, 0.5% for snow melting and cooling, and 0.2% for other uses. Energy savings amounted to 250 million barrels (38 million tonnes) of equivalent oil annually, preventing 33 million tonnes of carbon and 107 million tonnes of CO 2 being released to the atmosphere which includes savings in geothermal heat pump cooling (compared to using fuel oil to generate electricity). (author)

Direct Utilization of Geothermal Energy

Directory of Open Access Journals (Sweden)

John W. Lund

2010-08-01

Full Text Available The worldwide application of geothermal energy for direct utilization is reviewed. This paper is based on the world update for direct-use presented at the World Geothermal Congress 2010 in Bali, Indonesia (WGC2010 [1] which also includes material presented at three world geothermal congresses in Italy, Japan and Turkey (WGC95, WGC2000 and WGC2005. This report is based on country update papers prepared for WGC2010 and data from other sources. Final update papers were received from 70 countries of which 66 reported some direct utilization of geothermal energy for WGC2010. Twelve additional countries were added to the list based on other sources of information. The 78 countries having direct utilization of geothermal energy, is a significant increase from the 72 reported in 2005, the 58 reported in 2000, and the 28 reported in 1995. An estimate of the installed thermal power for direct utilization at the end of 2009, reported from WGC2010 is 48,493 MWt, almost a 72 % increased over the 2005 data, growing at a compound rate of 11.4% annually with a capacity factor of 0.28. The thermal energy used is 423,830 TJ/year (117,740 GWh/yr, about a 55% increase over 2005, growing at a compound rate of 9.2% annually. The distribution of thermal energy used by category is approximately 47.2% for ground-source heat pumps, 25.8% for bathing and swimming (including balneology, 14.9% for space heating (of which 85% is for district heating, 5.5% for greenhouses and open ground heating, 2.8% for industrial process heating, 2.7% for aquaculture pond and raceway heating, 0.4% for agricultural drying, 0.5% for snow melting and cooling, and 0.2% for other uses. Energy savings amounted to 250 million barrels (38 million tonnes of equivalent oil annually, preventing 33 million tonnes of carbon and 107 million tonnes of CO2 being release to the atmosphere which includes savings in geothermal heat pump cooling (compared to using fuel oil to generate electricity.

Determining if a change to a proposal requires additional NEPA documentation: the Smithsonian Solution; TOPICAL

International Nuclear Information System (INIS)

ECCLESTON, C.H.

1999-01-01

Proposed actions tend to evolve over time. Once National Environmental Policy Act (NEPA) documentation is completed, agencies are at risk that subsequent changes may not be adequately covered or that existing NEPA documentation maybe completely invalidated. Neither NEPA nor its subsequent regulations provide sufficient direction for determining the degree to which a proposed action may change before preparation of new or supplemental documentation is necessary. Yet, decisionmakers are routinely involved in determining if a change to a proposed action departs, to such an extent, from the description presented in the NEPA document that additional documentation is necessary. Experience demonstrates that no two decisionmakers will completely agree, one decisionmaker might believe that a particular change would not require additional documentation, while the other concludes the exact opposite. Lacking definitive direction, decisionmakers and critics alike may point to a universe of potential considerations as the basis for defending their claim that a change in an action does or does not require new or additional NEPA documentation. Assertions are often based on equivocal opinions that can be neither proved nor disproved. Moreover, decisionmakers are frequently placed in an arduous dilemma of justifying a decision, for which there is no generally accepted methodology on which to base the decision. Lack of definitive direction can prolong the decisionmaking process, resulting in project delays. This can also lead to inappropriate levels of NEPA documentation, inconsistencies in decisionmaking, and increased risk of a legal challenge because of insufficient documentation. Clearly, a more systematic and less subjective approach is needed, A tool for streamlining the NEPA process, by reducing this degree of subjectivity, is presented in this paper

The Strength of Direct Ties

DEFF Research Database (Denmark)

Claussen, Jörg; Falck, Oliver; Grosjean, Thorsten

2012-01-01

We analyze the economic effects of a developer's connectedness in the electronic game industry. Knowledge spillovers between developers are likely to be of special relevance in this knowledge-intensive and regionally concentrated industry. We calculate social network measures for a developer......'s connectedness to other developers at multiple points in time. In a regression in which we exploit within-career variation in social network measures, we find that the number of direct ties a developer has to other developers has a strong effect on both a game's revenues and critics' scores. The quality...... of indirect ties makes no additional contribution to the game's success....

Ultra-high temperature direct propulsion

International Nuclear Information System (INIS)

Araj, K.J.; Slovik, G.; Powell, J.R.; Ludewig, H.

1987-01-01

Potential advantages of ultra-high exhaust temperature (3000 K - 4000 K) direct propulsion nuclear rockets are explored. Modifications to the Particle Bed Reactor (PBR) to achieve these temperatures are described. Benefits of ultra-high temperature propulsion are discussed for two missions - orbit transfer (ΔV = 5546 m/s) and interplanetary exploration (ΔV = 20000 m/s). For such missions ultra-high temperatures appear to be worth the additional complexity. Thrust levels are reduced substantially for a given power level, due to the higher enthalpy caused by partial disassociation of the hydrogen propellant. Though technically challenging, it appears potentially feasible to achieve such ultra high temperatures using the PBR

Bright metal coatings from sustainable electrolytes: the effect of molecular additives on electrodeposition of nickel from a deep eutectic solvent.

Science.gov (United States)

Abbott, Andrew P; Ballantyne, Andrew; Harris, Robert C; Juma, Jamil A; Ryder, Karl S

2017-01-25

Organic and inorganic additives are often added to nickel electroplating solutions to improve surface finish, reduce roughness and promote uniform surface morphology of the coatings. Such additives are usually small molecules and often referred to as brighteners or levellers. However, there have been limited investigations into the effect of such additives on electrodeposition from ionic liquids (ILs) and deep eutectic solvents (DESs). Here we study the effect of four additives on electrolytic nickel plating from an ethyleneglycol based DES; these are nicotinic acid (NA), methylnicotinate (MN), 5,5-dimethylhydantoin (DMH) and boric acid (BA). The additives show limited influence on the bulk Ni(ii) speciation but have significant influence on the electrochemical behaviour of Ni deposition. Small concentrations (ca. 15 mM) of NA and MN show inhibition of Ni(ii) reduction whereas high concentrations of DMH and BA are required for a modest difference in behaviour from the additive free system. NA and MN also show that they significantly alter the nucleation and growth mechanism when compared to the additive free system and those with DMH and BA. Each of the additive systems had the effect of producing brighter and flatter bulk electrodeposits with increased coating hardness but XRD shows that NA and MN direct crystal growth to the [111] orientation whereas DMH and BA direct crystal growth to the [220] orientation.

An Inventory of Methods for the Assessment of Additive Increased Addictiveness of Tobacco Products.

Science.gov (United States)

van de Nobelen, Suzanne; Kienhuis, Anne S; Talhout, Reinskje

2016-07-01

Cigarettes and other forms of tobacco contain the addictive drug nicotine. Other components, either naturally occurring in tobacco or additives that are intentionally added during the manufacturing process, may add to the addictiveness of tobacco products. As such, these components can make cigarette smokers more easily and heavily dependent.Efforts to regulate tobacco product dependence are emerging globally. Additives that increase tobacco dependence will be prohibited under the new European Tobacco Product Directive. This article provides guidelines and recommendations for developing a regulatory strategy for assessment of increase in tobacco dependence due to additives. Relevant scientific literature is summarized and criteria and experimental studies that can define increased dependence of tobacco products are described. Natural tobacco smoke is a very complex matrix of components, therefore analysis of the contribution of an additive or a combination of additives to the level of dependence on this product is challenging. We propose to combine different type of studies analyzing overall tobacco product dependence potential and the functioning of additives in relation to nicotine. By using a combination of techniques, changes associated with nicotine dependence such as behavioral, physiological, and neurochemical alterations can be examined to provide sufficient information.Research needs and knowledge gaps will be discussed and recommendations will be made to translate current knowledge into legislation. As such, this article aids in implementation of the Tobacco Product Directive, as well as help enable regulators and researchers worldwide to develop standards to reduce dependence on tobacco products. This article provides an overall view on how to assess tobacco product constituents for their potential contribution to use and dependence. It provides guidelines that help enable regulators worldwide to develop standards to reduce dependence on tobacco products

Polylactides in additive biomanufacturing.

Science.gov (United States)

Poh, Patrina S P; Chhaya, Mohit P; Wunner, Felix M; De-Juan-Pardo, Elena M; Schilling, Arndt F; Schantz, Jan-Thorsten; van Griensven, Martijn; Hutmacher, Dietmar W

2016-12-15

New advanced manufacturing technologies under the alias of additive biomanufacturing allow the design and fabrication of a range of products from pre-operative models, cutting guides and medical devices to scaffolds. The process of printing in 3 dimensions of cells, extracellular matrix (ECM) and biomaterials (bioinks, powders, etc.) to generate in vitro and/or in vivo tissue analogue structures has been termed bioprinting. To further advance in additive biomanufacturing, there are many aspects that we can learn from the wider additive manufacturing (AM) industry, which have progressed tremendously since its introduction into the manufacturing sector. First, this review gives an overview of additive manufacturing and both industry and academia efforts in addressing specific challenges in the AM technologies to drive toward AM-enabled industrial revolution. After which, considerations of poly(lactides) as a biomaterial in additive biomanufacturing are discussed. Challenges in wider additive biomanufacturing field are discussed in terms of (a) biomaterials; (b) computer-aided design, engineering and manufacturing; (c) AM and additive biomanufacturing printers hardware; and (d) system integration. Finally, the outlook for additive biomanufacturing was discussed. Copyright © 2016 Elsevier B.V. All rights reserved.

Exploring light mediators with low-threshold direct detection experiments

Energy Technology Data Exchange (ETDEWEB)

Kahlhoefer, Felix [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); RWTH Aachen Univ. (Germany). Inst. for Theoretical Particle Physics and Cosmology; Kulkarni, Suchita [Oesterreichische Akademie der Wissenschaften, Vienna (Austria). Inst. fuer Hochenergiephysik; Wild, Sebastian [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2017-11-15

We explore the potential of future cryogenic direct detection experiments to determine the properties of the mediator that communicates the interactions between dark matter and nuclei. Due to their low thresholds and large exposures, experiments like CRESST-III, SuperCDMS SNOLAB and EDELWEISS-III will have excellent capability to reconstruct mediator masses in the MeV range for a large class of models. Combining the information from several experiments further improves the parameter reconstruction, even when taking into account additional nuisance parameters related to background uncertainties and the dark matter velocity distribution. These observations may offer the intriguing possibility of studying dark matter self-interactions with direct detection experiments.

Exploring light mediators with low-threshold direct detection experiments

International Nuclear Information System (INIS)

Kahlhoefer, Felix

2017-11-01

We explore the potential of future cryogenic direct detection experiments to determine the properties of the mediator that communicates the interactions between dark matter and nuclei. Due to their low thresholds and large exposures, experiments like CRESST-III, SuperCDMS SNOLAB and EDELWEISS-III will have excellent capability to reconstruct mediator masses in the MeV range for a large class of models. Combining the information from several experiments further improves the parameter reconstruction, even when taking into account additional nuisance parameters related to background uncertainties and the dark matter velocity distribution. These observations may offer the intriguing possibility of studying dark matter self-interactions with direct detection experiments.

Research on Producing Green Dimension Directly From Hardwood Logs

Science.gov (United States)

Philip A. Araman

1995-01-01

Because of rising timber costs and an increasing demand for high-grade timber, suppliers of solid wood products need additional material options. We feel that European and Japanese processing concepts of producing green dimension and other clear material directly from logs could provide an answer. In this paper we present a brief overview of our research results on...

Collecting Societies, Competition and the Services Directive

DEFF Research Database (Denmark)

Riis, Thomas

2011-01-01

the harms to cultural diversity. In addition to the competition law complications, the Services Directive puts significant restrictions on the member states to adopt or maintain national rules for collecting societies and that creates an urgent need for adopting a framework directive for collecting......The market for collective management of copyrights in the EU is in transition and the collecting societies are facing a number of challenges primarily based on the EU rules on competition and the freedom to provide services. Some of the major right holders are withdrawing their rights from...... the system of reciprocal representation agreements which fragments the repertoire. This is partly due to the market evolution and the emergence of new business models but also promoted by the European Commission initiatives intended to introduce a certain degree of competition in the collective management...

(2E-3-(3,5-Dimethyl-1-phenyl-1H-pyrazol-4-yl-1-(2,5-dimethyl-3-thienylprop-2-en-1-one

Directory of Open Access Journals (Sweden)

Salman A. Khan

2010-04-01

Full Text Available The title compound, (2E-3-(3,5-dimethyl-1-phenyl-1H-pyrazol-4-yl-1-(2,5-dimethyl-3-thienylprop-2-en-1-one (3 was synthesized in high yield by aldol condensation of 3-acetyl-2,5-dimethylthiophene and 3,5-dimethyl-1-phenylpyrazole-4-carboxaldehyde in ethanolic NaOH at room temperature. Its structure was fully characterized by elemental analysis, IR, 1H NMR, 13C NMR and EI-MS spectral analysis.

Synthesis of high surface area nanomaterials and their application in catalysis

Energy Technology Data Exchange (ETDEWEB)

Chaudhary, Umesh [Iowa State Univ., Ames, IA (United States)

2016-05-01

The dissertation is organized in 4 chapters. Chapter 1 highlights the motivations behind our research along with a general introduction on ceria and carbon catalysts. Chapter 2 reports the investigations on Copper-Ceria catalysts for the selective hydrogenation of fatty acids into fatty alcohols. Chapter 3 discusses the development of nitrogen containing mesoporous carbon. The chapter also reports the catalytic investigations for aldol condensation and nitrobenzene hydrogenation reactions. Finally, Chapter 4 is a general conclusion summarizing this dissertation.

Organic chemistry experiment

International Nuclear Information System (INIS)

Mun, Seok Sik

2005-02-01

This book deals with organic chemistry experiments, it is divided five chapters, which have introduction, the way to write the experiment report and safety in the laboratory, basic experiment technic like recrystallization and extraction, a lot of organic chemistry experiments such as fischer esterification, ester hydrolysis, electrophilic aromatic substitution, aldol reaction, benzoin condensation, wittig reaction grignard reaction, epoxidation reaction and selective reduction. The last chapter introduces chemistry site on the internet and way to find out reference on chemistry.

Searching for additional Higgs bosons via Higgs cascades

Science.gov (United States)

Gao, Christina; Luty, Markus A.; Mulhearn, Michael; Neill, Nicolás A.; Wang, Zhangqier

2018-04-01

The discovery of a 125 GeV Higgs boson at the Large Hadron Collider strongly motivates direct searches for additional Higgs bosons. In a type I two Higgs doublet model there is a large region of parameter space at tan β ≳5 that is currently unconstrained experimentally. We show that the process g g →H →A Z →Z Z h can probe this region, and can be the discovery mode for an extended Higgs sector at the LHC. We analyze 9 promising decay modes for the Z Z h state, and we find that the most sensitive final states are ℓℓℓℓb b , ℓℓj j b b , ℓℓν ν γ γ and ℓℓℓℓ+ missing energy.

Education and training requirements in the revised European Basic Safety Standards Directive

International Nuclear Information System (INIS)

Mundigl, S.

2009-01-01

The European Commission is currently developing a modified European Basic Safety Standards Directive covering two major objectives: the consolidation of existing European Radiation Protection legislation, and the revision of the European Basic Safety Standards. The consolidation will merge the following five Directives into one single Directive: the Basic Safety Standards Directive, the Medical Exposures Directive, the Public Information Directive, the Outside Workers Directive, and the Directive on the Control of high-activity sealed radioactive sources and orphan sources. The revision of the European Basic Safety Standards will take account of the latest recommendations by the International Commission on Radiological Protection (ICRP) and shall improve clarity of the requirements where appropriate. It is planned to introduce more binding requirements on natural radiation sources, on criteria for clearance, and on the cooperation between Member States for emergency planning and response, as well as a graded approach for regulatory control. One additional goal is to achieve greater harmonisation between the European BSS and the international BSS. Following a recommendation from the Article 31 Group of Experts, the current draft of the modified BSS will highlight the importance of education and training by dedicating a specific title to radiation protection education, training and information. This title will include a general requirement on the Member States to ensure the establishment of an adequate legislative and administrative framework for providing appropriate radiation protection education, training and information. In addition, there will be specific requirements on training in the medical field, on information and training of workers in general, of workers potentially exposed to orphan sources, and to emergency workers. The revised BSS directive will include requirements on the competence of a radiation protection expert (RPE) and of a radiation protection

Direct activation of allylic alcohols in palladium catalyzed coupling reactions

NARCIS (Netherlands)

Gümrükçü, Y.

2014-01-01

The direct use of allylic alcohols in substitution reactions without pre-activation of the hydroxyl-group into a better leaving group or the use of additional stoichiometric in situ activators remains challenging due to the poor leaving group ability of the hydroxyl-group. Hence, it is important to

On the dynamic response of additively manufactured 316L

Science.gov (United States)

Smith, Liam; Eakins, Daniel; Chapman, David; Hooper, Paul

2017-06-01

Understanding the dynamic performance of Additively Manufactured (AM) materials is important when designing components for real-world applications. A series of Taylor tests were carried out on AM and conventionally manufactured 316L Stainless Steel. AM specimens were produced with a Renishaw AM250 selective laser melting machine. Taylor tests were conducted in a reverse anvil-on-rod configuration with soft capture and post loading measurements used to corroborate high speed deformation imaging. The influence of microstructure orientation and surface roughness was investigated by manufacturing samples parallel and perpendicular to build direction and with both as-built and machined finishes. Results were compared with optimised Johnson-Cook and Zerilli-Armstrong constitutive models within AUTODYN FE software.

Experimental Analysis of DI Diesel Engine Performance with Blend Fuels of Oxygenated Additive and COME Biodiesel

OpenAIRE

P. Venkateswara Rao; B.V. Appa Rao; D. Radhakrishna

2012-01-01

An experimental investigation was carried out to evaluate the effect of using Triacetin (T) as an additive with biodiesel on direct injection diesel engine for performance and combustion characteristics. Normally in the usage of diesel fuel and neat biodiesel, knocking can be detected to some extent. By adding triacetin [C9H14O6] additive to biodiesel, this problem can be alleviated to some extent and the tail pipe emissions are reduced. Comparative study was conducted using petro-diesel, bio...

Enhanced flux pinning in MOCVD-YBCO films through Zr additions: systematic feasibility studies

International Nuclear Information System (INIS)

Aytug, T; Paranthaman, M; Specht, E D; Zhang, Y; Kim, K; Zuev, Y L; Cantoni, C; Goyal, A; Christen, D K; Maroni, V A; Chen, Y; Selvamanickam, V

2010-01-01

Systematic effects of Zr additions on the structural and flux pinning properties of YBa 2 Cu 3 O 7-δ (YBCO) films deposited by metal-organic chemical vapor deposition (MOCVD) have been investigated. Detailed characterization, conducted by coordinated transport, x-ray diffraction, scanning and transmission electron microscopy analyses, and imaging Raman microscopy have revealed trends in the resulting property/performance correlations of these films with respect to varying mole percentages (mol%) of added Zr. For compositions ≤7.5 mol%, Zr additions lead to improved in-field critical current density, as well as extra correlated pinning along the c-axis direction of the YBCO films via the formation of columnar, self-assembled stacks of BaZrO 3 nanodots.

Direct plasma interaction with living tissue

Science.gov (United States)

Fridman, Gregory

For some time, plasma has been used in medicine to cauterize or cut tissue using heat and mechanical energy. In the recent decade, some researchers around the world have started to investigate how gas jets that pass through thermal plasma can be employed in medicine. This thesis presents the first investigation of biomedical uses of non-thermal plasma discharge which comes in direct contact with living tissue. It is demonstrated that the direct application of non-thermal plasma in air can cause rapid deactivation of bacteria on surfaces of tissues without causing any visible tissue damage. Medical need for such a device is discussed. Construction and operation of various types of non-thermal plasma power supplies and many types of treatment electrodes are presented as well. Application of this plasma to living organisms is shown to be safe from both the electrical perspective and from the biological perspective. Biological safety is revealed through a series of differential skin toxicity trials on human cadaver tissue, live hairless mouse skin tissue, live pig skin tissue, and finally in an open wound model on pigs. Direct non-thermal plasma in air is shown to deactivate bacteria about 100 times faster than indirect application using jets. A series of experiments reveal that this effectiveness is due to the ability of direct discharge to bring charges to tissue surfaces. It is demonstrated that neither ultraviolet (UV) radiation nor neutral active species such as hydroxyl radicals or ozone produced in plasma are responsible for the main effect on bacteria. Although much additional work remains on establishing detailed mechanism by which charges from plasma achieve this effect, the work carried out in this thesis clearly demonstrates that direct application of non-thermal plasma in air can be a very useful tool in medicine.

Direct and indirect effects of organizational justice on work ability.

Science.gov (United States)

Spanier, K; Radoschewski, F M; Gutenbrunner, C; Bethge, M

2014-12-01

Organizational justice (OJ), involving transparent workplace procedures and treating staff members with respect, has been of growing concern in recent epidemiological research as a determinant of health-related outcomes. To examine the factorial validity of the German version of Moorman's Organizational Justice Questionnaire (OJQ), to investigate the direct cross-sectional effect of OJ on self-rated work ability and to analyse if there is an additional indirect effect of OJ on work ability mediated by effort-reward imbalance. An analysis of cross-sectional data from the Second German Sociomedical Panel of Employees, involving white-collar workers employed at least half time. We performed confirmatory factor analyses to test the factorial validity of the OJQ and analysed the direct and indirect associations of OJ and self-rated work ability by path model analysis. Of the 1217 participants (47% female; mean age: 51) 36% had poor work ability. Factor analyses confirmed the two-factor structure of the German OJQ. Work ability was explained directly by OJ (β = 0.30) and effort-reward imbalance (β = -0.27). Additionally, we identified an indirect effect of OJ that was mediated by effort-reward imbalance (β = 0.14). The total effect of OJ on work ability was remarkably strong (β = 0.44). Associations remained unchanged after adjustment for socio-demographic parameters. This study showed the importance of considering additional indirect pathways when examining the impact of OJ on the work ability of employees. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Immobilization of radioactive waste through cementation using Cuban zeolitic rock as additive

International Nuclear Information System (INIS)

Chales Suarez, G.; Castillo Gomez, R.

1997-01-01

The cementation of both simulated and real low level aqueous wastes using Cuban zeolite as additive is described. Mechanical characteristics and leach testing of the cemented waste forms has been studied. The results obtained have shown that the presence of zeolite in the cemented waste for reduces considerably the leach rates of Cs and Co and moreover, mechanical characteristics (set time and compressive strength) are better when compared with direct cementation of aqueous wastes. (author). 13 refs, 8 tabs

Additives in yoghurt production

Directory of Open Access Journals (Sweden)

Milna Tudor

2008-02-01

Full Text Available In yoghurt production, mainly because of sensory characteristics, different types of additives are used. Each group, and also each substance from the same group has different characteristics and properties. For that reason, for improvement of yoghurt sensory characteristics apart from addition selection, the quantity of the additive is very important. The same substance added in optimal amount improves yoghurt sensory attributes, but too small or too big addition can reduce yoghurt sensory attributes. In this paper, characteristics and properties of mostly used additives in yoghurt production are described; skimmed milk powder, whey powder, concentrated whey powder, sugars and artificial sweeteners, fruits, stabilizers, casein powder, inulin and vitamins. Also the impact of each additive on sensory and physical properties of yoghurt, syneresis and viscosity, are described, depending on used amount added in yoghurt production.

Effect of surface roughness on the fatigue life of laser additive manufactured Ti6Al4V alloy

Czech Academy of Sciences Publication Activity Database

Bača, A.; Konečná, R.; Nicoletto, G.; Kunz, Ludvík

2015-01-01

Roč. 15, č. 4 (2015), s. 498-502 ISSN 1213-2489 Institutional support: RVO:68081723 Keywords : Additive manufacturing * direct metal laser sintering * Fatigue life Subject RIV: JL - Materials Fatigue, Friction Mechanics

Direct and vicarious violent victimization and juvenile delinquency: an application of general strain theory.

Science.gov (United States)

Lin, Wen-Hsu; Cochran, John K; Mieczkowski, Thomas

2011-01-01

Using a national probability sample of adolescents (12–17), this study applies general strain theory to how violent victimization, vicarious violent victimization, and dual violent victimization affect juvenile violent/property crime and drug use. In addition, the mediating effect and moderating effect of depression, low social control, and delinquent peer association on the victimization–delinquency relationship is also examined. Based on SEM analyses and contingency tables, the results indicate that all three types of violent victimization have significant and positive direct effects on violent/property crime and drug use. In addition, the expected mediating effects and moderating effects are also found. Limitations and future directions are discussed.

Additive Manufacturing Infrared Inspection

Science.gov (United States)

Gaddy, Darrell; Nettles, Mindy

2015-01-01

The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

Multifunctional four-port directional control valve constructed from logic valves

International Nuclear Information System (INIS)

Lisowski, E.; Czyżycki, W.; Rajda, J.

2014-01-01

Highlights: • Directional valve with standard ISO 440-08 has been constructed from logic valves. • Only one innovative valve may replace whole family of the standard valves. • CFD analysis and bench tests of the innovative valve has been carried. • Parameters of the innovative valve are equaling or surpassing the standard ones. • The innovative valve has additional possibilities of pressure and flow control. - Abstract: The paper refers to four-port solenoid pilot operated valves, which are subplate mounted in a hydraulic system in accordance with the ISO 4401 standard. Their widespread use in many machines and devices causes a continuing interest in the development of their design by both the scientific centers and the industry. This paper presents an innovative directional control valve based on the use of logic valves and a methodology followed for the design of it by using Solid Edge CAD and ANSYS/Fluent CFD software. The valve design methodology takes into account the need to seek solutions that minimize flow resistance through the valve. For this purpose, the flow paths are prepared by means of CAD software and pressure-flow curves are determined as a result of CFD analysis. The obtained curves are compared with the curves available in the catalogs of spool type directional control valves. The new solution allows to replace the whole family of spool type four-port directional control valves by one valve built of logic valves. In addition, the innovative directional control valve provides leak-proof shutting the flow paths off and also it can control flow rate and even pressure of working liquid. A prototype of the valve designed by the presented method has been made and tested on the test bench. The results quoted in the paper confirm that the developed logic type directional control valve is able to meet all designed connection configurations, and the obtained pressure-flow curves show very good conformity with the results of CFD analysis

Physician Self-directed Learning and Education

Directory of Open Access Journals (Sweden)

Masami Tagawa

2008-07-01

Full Text Available Physicians are expected to be life-long learners because updated and effective patient care should be provided while medical and clinical knowledge and skills and social requirements for patient care are rapidly changing. Also, qualified clinical competence needs long periods of training and each physician has to continually learn as long as he/she works as a professional. Self-directed learning is an important factor in adult learning. Medical students' readiness for self-directed learning is not high, and should be improved by medical school and postgraduate training curricula. Garrison proposed a comprehensive model of self-directed learning, and it has dimensions of motivation (entering and task, self-monitoring (responsibility, and self-management (responsibility. To teach individual self-directed learning competencies, the following are important: (1 situate learners to experience “real” problems; (2 encourage learners to reflect on their own performance; (3 create an educational atmosphere in clinical training situations. In 2005, a 2-year mandatory residency program was implemented in Japan, and fewer medical school graduates took residency programs in medical school hospitals and advanced specialty programs provided by medical school departments. Medical school departments provide traditional, but life-long clinical training opportunities. Under the new residency program, an additional postgraduate and continuing medical training system has to be built up to maintain and confirm a physician's competencies. If physicians do clinical work using a scholarly way of thinking with critical analysis of their own competencies and improvement by reflection, they will become an excellent life-long learner.

Computational Fluid Dynamics and Additive Manufacturing to Diagnose and Treat Cardiovascular Disease.

Science.gov (United States)

Randles, Amanda; Frakes, David H; Leopold, Jane A

2017-11-01

Noninvasive engineering models are now being used for diagnosing and planning the treatment of cardiovascular disease. Techniques in computational modeling and additive manufacturing have matured concurrently, and results from simulations can inform and enable the design and optimization of therapeutic devices and treatment strategies. The emerging synergy between large-scale simulations and 3D printing is having a two-fold benefit: first, 3D printing can be used to validate the complex simulations, and second, the flow models can be used to improve treatment planning for cardiovascular disease. In this review, we summarize and discuss recent methods and findings for leveraging advances in both additive manufacturing and patient-specific computational modeling, with an emphasis on new directions in these fields and remaining open questions. Copyright © 2017 Elsevier Ltd. All rights reserved.

From energy efficiency towards resource efficiency within the Ecodesign Directive

DEFF Research Database (Denmark)

Bundgaard, Anja Marie; Mosgaard, Mette; Remmen, Arne

2017-01-01

on the most significant environmental impact has often resulted in a focus on energy efficiency in the use phase. Therefore, the Ecodesign Directive should continue to target resource efficiency aspects but also consider environ- mental aspects with a large improvement potential in addition to the most...... significant environmental impact. For the introduction of resource efficiency requirements into the Ecodesign Directive, these requirements have to be included in the preparatory study. It is therefore recommended to broaden the scope of the Methodology for the Ecodesign of Energy-related products and the Eco......The article examines the integration of resource efficiency into the European Ecodesign Directive. The purpose is to analyse the processes and stakeholder interactions, which formed the basis for integrating resource efficiency requirements into the implementing measure for vacuum cleaners...

Direct numerical simulation of fractal-generated turbulence

International Nuclear Information System (INIS)

Suzuki, H; Hasegawa, Y; Ushijima, T; Nagata, K; Sakai, Y; Hayase, T

2013-01-01

We simulate fractal-generated turbulence (Hurst and Vassilicos 2007 Phys. Fluids 19 035103)) by means of a direct numerical simulation and address its fundamental characteristics. We examine whether the fractal-generated turbulence in the upstream region has a nature similar to that of a wake. We propose an equation for predicting peak values of the velocity fluctuation intensity and devise a method for formulating the functional form of the quantity of interest by focusing on the time scale of decaying turbulence, and we examine those forms for the turbulent kinetic energy and rms of pressure fluctuation through this method. By using the method, both of these functional forms are found to be power-law functions in the downstream region, even though these profiles follow exponential functions around these peaks. In addition, decay exponents of these quantities are estimated. The integral length scales of velocity fluctuations for transverse as well as streamwise directions are essentially constant in the downstream direction. Decaying turbulence having both these characteristics conflicts with decaying turbulence described by the theory predicting exponential decay. We discuss a factor causing the difference by focusing on the functional form of the transfer function of homogeneous, isotropic turbulence. (paper)

76 FR 33121 - List of Approved Spent Fuel Storage Casks: HI-STORM Flood/Wind Addition

Science.gov (United States)

2011-06-08

... Storage Casks: HI-STORM Flood/Wind Addition AGENCY: Nuclear Regulatory Commission. ACTION: Direct final... regulations to add the Holtec HI-STORM Flood/Wind cask system to the ``List of Approved Spent Fuel Storage... Title 10 of the Code of Federal Regulations Section 72.214 to add the Holtec HI- STORM Flood/Wind cask...

Additive manufacturing of tools for lapping glass

Science.gov (United States)

Williams, Wesley B.

2013-09-01

Additive manufacturing technologies have the ability to directly produce parts with complex geometries without the need for secondary processes, tooling or fixtures. This ability was used to produce concave lapping tools with a VFlash 3D printer from 3D Systems. The lapping tools were first designed in Creo Parametric with a defined constant radius and radial groove pattern. The models were converted to stereolithography files which the VFlash used in building the parts, layer by layer, from a UV curable resin. The tools were rotated at 60 rpm and used with 120 grit and 220 grit silicon carbide lapping paste to lap 0.750" diameter fused silica workpieces. The samples developed a matte appearance on the lapped surface that started as a ring at the edge of the workpiece and expanded to the center. This indicated that as material was removed, the workpiece radius was beginning to match the tool radius. The workpieces were then cleaned and lapped on a second tool (with equivalent geometry) using a 3000 grit corundum aluminum oxide lapping paste, until a near specular surface was achieved. By using lapping tools that have been additively manufactured, fused silica workpieces can be lapped to approach a specified convex geometry. This approach may enable more rapid lapping of near net shape workpieces that minimize the material removal required by subsequent polishing. This research may also enable development of new lapping tool geometry and groove patterns for improved loose abrasive finishing.

Spatially dependent properties in a laser additive manufactured Ti–6Al–4V component

Energy Technology Data Exchange (ETDEWEB)

Palanivel, S.; Dutt, A.K. [Center for Friction Stir Processing, Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States); Faierson, E.J. [Quad City Manufacturing Laboratory, Western Illinois University, Rock Island, IL 61201 (United States); Mishra, R.S., E-mail: Rajiv.Mishra@unt.edu [Center for Friction Stir Processing, Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States)

2016-01-27

Automotive and aerospace sectors have provided a strong product pull for advancing powder bed fusion technologies. However, as these technologies mature towards large-scale production, issues of build consistency and surface finish are of concern. In order to study these issues, a Ti–6Al–4V mini impeller was fabricated using laser additive manufacturing. The primary objective of this work was to quantify and correlate the variation in mechanical properties and microstructure across and along different locations in the component. Hardness measured at various build locations revealed a stronger hub (highest value: 428 HV) with lower spatial variations in comparison to the blade (highest value: 415 HV). Additional examinations to assess anisotropy showed an average hardness of 397±11 and 385±8 HV along the blade build (Z) and longitudinal (X) directions respectively. Region and direction specific uniaxial tensile testing of the samples indicated a strong hub bottom with yield strength (YS) of 1193 MPa, ultimate tensile strength (UTS) of 1310 MPa, and a total elongation of 5.5% in the longitudinal direction. Although the low elongation value correlates well with previous studies, strength is significantly higher and is attributed to having a complete martensitic structure induced by the high cooling rates experienced at the build–substrate interface. On the other hand, YS, UTS and total elongation in the blade were recorded as 978 MPa, 1096 MPa and 9.12%, respectively, along the build direction. Microstructure in the blade region consisted of α′ and α+β. When compared to the polished specimen in the blade, its unpolished counterpart yielded at 896 MPa, had UTS of 1018 MPa, and elongation of 6.24%. An understanding of the reduction in performance of the unfinished blade would help in deciding the need for surface finishing operations after fabrication.

Spatially dependent properties in a laser additive manufactured Ti–6Al–4V component

International Nuclear Information System (INIS)

Palanivel, S.; Dutt, A.K.; Faierson, E.J.; Mishra, R.S.

2016-01-01

Automotive and aerospace sectors have provided a strong product pull for advancing powder bed fusion technologies. However, as these technologies mature towards large-scale production, issues of build consistency and surface finish are of concern. In order to study these issues, a Ti–6Al–4V mini impeller was fabricated using laser additive manufacturing. The primary objective of this work was to quantify and correlate the variation in mechanical properties and microstructure across and along different locations in the component. Hardness measured at various build locations revealed a stronger hub (highest value: 428 HV) with lower spatial variations in comparison to the blade (highest value: 415 HV). Additional examinations to assess anisotropy showed an average hardness of 397±11 and 385±8 HV along the blade build (Z) and longitudinal (X) directions respectively. Region and direction specific uniaxial tensile testing of the samples indicated a strong hub bottom with yield strength (YS) of 1193 MPa, ultimate tensile strength (UTS) of 1310 MPa, and a total elongation of 5.5% in the longitudinal direction. Although the low elongation value correlates well with previous studies, strength is significantly higher and is attributed to having a complete martensitic structure induced by the high cooling rates experienced at the build–substrate interface. On the other hand, YS, UTS and total elongation in the blade were recorded as 978 MPa, 1096 MPa and 9.12%, respectively, along the build direction. Microstructure in the blade region consisted of α′ and α+β. When compared to the polished specimen in the blade, its unpolished counterpart yielded at 896 MPa, had UTS of 1018 MPa, and elongation of 6.24%. An understanding of the reduction in performance of the unfinished blade would help in deciding the need for surface finishing operations after fabrication.

Identification of additives in poly(vinylacetate) artist's paints using PY-GC-MS.

Science.gov (United States)

Silva, Miguel F; Doménech-Carbó, Maria Teresa; Fuster-López, Laura; Mecklenburg, Marion F; Martin-Rey, Susana

2010-05-01

Commercial poly(vinyl acetate) (PVAc) paint formulations for artists include a number of compounds in addition to the PVAc polymer and pigments to improve the physical and chemical properties of the resulting product. Among the most common additives are surfactants, coalescing agents, defoamers, freeze-thaw agents and thickeners. These products significantly influence the behaviour of the dried film. Nevertheless, they are usually difficult to detect with conventional analytical methods given their low concentration. In order to identify these additives, present in the dried film as minor components, an analytical method based on in situ thermally assisted pyrolysis-silylation gas chromatography-mass spectrometry (GC-MS) using hexamethyldisilazane as a derivatisation reagent is proposed. This method improves the conventional GC-MS analysis performed by direct pyrolysis and enables the simultaneous identification of the PVAc binding medium and the additives included by the manufacturer in the commercial paint. Five different commercial PVAc paints have been analysed, namely, armour green, burnt umber, oriental red, raw umber and white from Flashe. Internal plasticiser VeoVa consisting of C(10) fatty acids with highly branched chains has been recognised from the MS spectra. On the other hand, the differences found in the additive content of the studied paints, in particular the poly(ethylene glycol)-type surfactant, are in good agreement with their mechanical properties.

CT image segmentation methods for bone used in medical additive manufacturing.

Science.gov (United States)

van Eijnatten, Maureen; van Dijk, Roelof; Dobbe, Johannes; Streekstra, Geert; Koivisto, Juha; Wolff, Jan

2018-01-01

The accuracy of additive manufactured medical constructs is limited by errors introduced during image segmentation. The aim of this study was to review the existing literature on different image segmentation methods used in medical additive manufacturing. Thirty-two publications that reported on the accuracy of bone segmentation based on computed tomography images were identified using PubMed, ScienceDirect, Scopus, and Google Scholar. The advantages and disadvantages of the different segmentation methods used in these studies were evaluated and reported accuracies were compared. The spread between the reported accuracies was large (0.04 mm - 1.9 mm). Global thresholding was the most commonly used segmentation method with accuracies under 0.6 mm. The disadvantage of this method is the extensive manual post-processing required. Advanced thresholding methods could improve the accuracy to under 0.38 mm. However, such methods are currently not included in commercial software packages. Statistical shape model methods resulted in accuracies from 0.25 mm to 1.9 mm but are only suitable for anatomical structures with moderate anatomical variations. Thresholding remains the most widely used segmentation method in medical additive manufacturing. To improve the accuracy and reduce the costs of patient-specific additive manufactured constructs, more advanced segmentation methods are required. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Scheduling and Topology Design in Networks with Directional Antennas

Science.gov (United States)

2017-05-19

Scheduling and Topology Design in Networks with Directional Antennas Thomas Stahlbuhk, Nathaniel M. Jones, Brooke Shrader Lincoln Laboratory...controllers must choose which pairs of nodes should communicate in order to establish a topology over which traffic can be sent. Additionally...interacting effects of topology design and transmission scheduling in wireless networks, in particular focusing on networks where nodes are divided into

The value relevance of direct cash flows under international financial reporting standards

OpenAIRE

Clacher, I; de Ricquebourg, AD; Hodgson, A

2013-01-01

This study examines if there has been a change in the value relevance of direct cash flow components since the adoption of International Financial Reporting Standards (IFRS) in Australia. Our results show that for both industrial and extractive firms direct cash flow statements are value relevant under Australian Generally Accepted Accounting Principles (AGAAP) and remain so after the adoption of IFRS. In addition, for industrial firms there is a significant increase in the value relevance of...

Direct marketing of electricity from biogas plants; Direktvermarktung von Strom aus Biogasanlagen. Chancen und Risiken aus rechtlicher Sicht

Energy Technology Data Exchange (ETDEWEB)

Falke, Iris; Schlichting, Julia [Schnutenhaus und Kollegen, Rechtsanwaelte, Berlin (Germany)

2013-10-01

The German Renewable Energy Sources Act of January, 1{sup st} 2012 contains new possibilities of direct selling electricity to the market, to promote and to improve market integration of electricity generated from renewable energies. The core is the introduction of a market premium for electricity which has actually been fed into the grid system and purchased by a third party. In addition to his market revenues, the installation operator receives the market premium. The market premium replaces the guaranteed EEG feed-in tariff. The market premium should cover the difference between the proceeds from direct selling and the EEG feed-in tariff. In addition, installation operators receive a management premium to compensate their transaction costs. As a supplement to the market premium model the EEG 2012 introduces a flexibility premium to create an economic incentive for providing additional capacities and encourage a demand-oriented electricity production. Further possibilities of direct marketing are the ''green electricity privilege'' and the non-subsided direct marketing. This article provides an over-view of the different forms of direct-marketing that are included in EEG 2012 with a focus on the market premium and the flexibility premium. These two instruments are of high importance to operators of installations generating electricity from biogas. A further emphasis is put on risks and chances in contract negotiation in the context of direct marketing. (orig.)

Enhancement of the anaerobic hydrolysis and fermentation of municipal solid waste in leachbed reactors by varying flow direction during water addition and leachate recycle

Energy Technology Data Exchange (ETDEWEB)

Uke, Matthew N., E-mail: cnmnu@leeds.ac.uk [Department of Civil Engineering, University of Leeds, Leeds LS2 9JT (United Kingdom); Stentiford, Edward [Department of Civil Engineering, University of Leeds, Leeds LS2 9JT (United Kingdom)

2013-06-15

Highlights: ► Combined downflow and upflow water addition improved hydraulic conductivity. ► Upflow water addition unclogged perforated screen leading to more leachate flow. ► The volume of water added and transmitted positively correlated with hydrolysis process. ► Combined downflow and upflow water addition increased COD production and yield. ► Combined downflow and upflow leachate recycle improved leachate and COD production. - Abstract: Poor performance of leachbed reactors (LBRs) is attributed to channelling, compaction from waste loading, unidirectional water addition and leachate flow causing reduced hydraulic conductivity and leachate flow blockage. Performance enhancement was evaluated in three LBRs M, D and U at 22 ± 3 °C using three water addition and leachate recycle strategies; water addition was downflow in D throughout, intermittently upflow and downflow in M and U with 77% volume downflow in M, 54% volume downflow in U while the rest were upflow. Leachate recycle was downflow in D, alternately downflow and upflow in M and upflow in U. The strategy adopted in U led to more water addition (30.3%), leachate production (33%) and chemical oxygen demand (COD) solubilisation (33%; 1609 g against 1210 g) compared to D (control). The total and volatile solids (TS and VS) reductions were similar but the highest COD yield (g-COD/g-TS and g-COD/g-VS removed) was in U (1.6 and 1.9); the values were 1.33 and 1.57 for M, and 1.18 and 1.41 for D respectively. The strategy adopted in U showed superior performance with more COD and leachate production compared to reactors M and D.

Genetic parameters for direct and maternal calving ease in Walloon dairy cattle based on linear and threshold models.

Science.gov (United States)

Vanderick, S; Troch, T; Gillon, A; Glorieux, G; Gengler, N

2014-12-01

Calving ease scores from Holstein dairy cattle in the Walloon Region of Belgium were analysed using univariate linear and threshold animal models. Variance components and derived genetic parameters were estimated from a data set including 33,155 calving records. Included in the models were season, herd and sex of calf × age of dam classes × group of calvings interaction as fixed effects, herd × year of calving, maternal permanent environment and animal direct and maternal additive genetic as random effects. Models were fitted with the genetic correlation between direct and maternal additive genetic effects either estimated or constrained to zero. Direct heritability for calving ease was approximately 8% with linear models and approximately 12% with threshold models. Maternal heritabilities were approximately 2 and 4%, respectively. Genetic correlation between direct and maternal additive effects was found to be not significantly different from zero. Models were compared in terms of goodness of fit and predictive ability. Criteria of comparison such as mean squared error, correlation between observed and predicted calving ease scores as well as between estimated breeding values were estimated from 85,118 calving records. The results provided few differences between linear and threshold models even though correlations between estimated breeding values from subsets of data for sires with progeny from linear model were 17 and 23% greater for direct and maternal genetic effects, respectively, than from threshold model. For the purpose of genetic evaluation for calving ease in Walloon Holstein dairy cattle, the linear animal model without covariance between direct and maternal additive effects was found to be the best choice. © 2014 Blackwell Verlag GmbH.

DESAIN DAN SINTESIS SENYAWA ACES (ANALOG CURCUMIN SERIES DENGAN METODE SOLID PHASE REACTION SEBAGAI SENYAWA ANTIKANKER POTEN DENGAN MEKANISME MENGHAMBAT PROTEIN NF-kB

Directory of Open Access Journals (Sweden)

Monica Sabrina Widiapranolo

2016-04-01

Full Text Available Abstract: Analog of curcumin in forms of enone and dienone aromatic is known for their activity as an NF-κB inhibitor. In this study, will be synthesize 2-(4'-N, N-dimethylamino benzilidine cyclohexane-1,3-dione as an analog that predicted has an activity as an NF-κB inhibitor. This research was conducted based on the crossed aldol condensation reaction by reacting 3 mmole pN,N-dimethylamino benzaldehide and 6 mmole cyclohexane-1,3-dione with hydrochloric acid as the catalyst using solid phase reaction method. Based on computational analysis, 2-(4'-N,Ndimethylamino benzilidine cyclohexane-1,3-dione showed a better interaction with NF-κB protein with PLANTSPLP score was -69,7895. The outcome of the reaction was yellow colored powder, no odor and soluble in hydrochloric acid 3N. The yield value was 78.8%. Liquid chromatography showed 100% purity. The melting point range was 237.5-240.3°C. The results of structure elucidation by 1H-NMR, infrared and mass spectroscopy tests indicated the compound was 2-(4-(dimetilaminobenzilidena-4-(3-oksosiklohex-1-enil sikloheksana-1,3-dion. Key words: 2-(4'-N, N-dimethylamino benzilidine cyclohexane-1,3-dione, crossed aldol condensation, solid phase reaction.

Synthesis and Antiplasmodial Activity of 2-(4-Methoxyphenyl-4-Phenyl-1,10-Phenanthroline Derivative Compounds

Directory of Open Access Journals (Sweden)

Nazudin

2012-08-01

Full Text Available A unique of synthetic methods was employed to prepare 2-(4-methoxyphenyl-4-phenyl-1,10-phenanthroline (5 derivatives from 4-methoxy-benzaldehyde (1, acetophenone (2, and 8-aminoquinoline (4 with aldol condensation and cyclization reactions. The derivatives were tested through antiplasmodial test. The synthesis of derivatives compound 5 was conducted in three steps. The 3-(4-methoxyphenyl-1-phenylpropenone 3 was synthesized through aldol condensation of 1 and 2 which has a yield of 96.42%. The compound 5 was synthesized through cyclization of compound 4 and 3 with 84.55% yield. The derivative of compound 5 was synthesized from compound 5 using DMS and DES reagents which refluxed for 21 and 22 h, to produce (1-N-methyl-9-(4-methoxyphenyl-7-phenyl-1,10-phenanthrolinium sulfate (6 and (1-N-ethyl-9-(4-methoxyphenyl-7-phenyl-1,10-phenanthrolinium sulfate (7 with 91.42 and 86.36% yields, respectively. Results of in vitro testing of antiplasmodial activity of compound 5 derivatives (i.e., compound 6 and 7 against chloroquine-resistant P. falciparum FCR3 strain showed that compound 7 had higher antimalarial activity than compounds 5 and 6. Whereas, results of in vitro testing against chloroquine-sensitive P. falciparum D10 strain showed that compound 6 has higher antimalarial activity than compounds 5 and 7.

On the adsorption/reaction of acetone on pure and sulfate-modified zirconias.

Science.gov (United States)

Crocellà, Valentina; Cerrato, Giuseppina; Morterra, Claudio

2013-08-28

In situ FTIR spectroscopy was employed to investigate some aspects of the ambient temperature (actually, IR-beam temperature) adsorption of acetone on various pure and sulfate-doped zirconia specimens. Acetone uptake yields, on all examined systems and to a variable extent, different types of specific molecular adsorption, depending on the kind/population of available surface sites: relatively weak H-bonding interaction(s) with surface hydroxyls, medium-strong coordinative interaction with Lewis acidic sites, and strong H-bonding interaction with Brønsted acidic centres. Moreover acetone, readily and abundantly adsorbed in molecular form, is able to undergo the aldol condensation reaction (yielding, as the main reaction product, adsorbed mesityl oxide) only if the adsorbing material possesses some specific surface features. The occurrence/non-occurrence of the acetone self-condensation reaction is discussed, and leads to conclusions concerning the sites that catalyze the condensation reaction that do not agree with either of two conflicting interpretations present in the literature of acetone uptake/reaction on, mainly, zeolitic systems. In particular, what turns out to be actually necessary for the acetone aldol condensation reaction to occur on the examined zirconia systems is the presence of coordinatively unsaturated O(2-) surface sites of basicity sufficient to lead to the extraction of a proton from one of the CH3 groups of adsorbed acetone.

Compressed Sensing-Based Direct Conversion Receiver

DEFF Research Database (Denmark)

Pierzchlewski, Jacek; Arildsen, Thomas; Larsen, Torben

2012-01-01

Due to the continuously increasing computational power of modern data receivers it is possible to move more and more processing from the analog to the digital domain. This paper presents a compressed sensing approach to relaxing the analog filtering requirements prior to the ADCs in a direct......-converted radio signals. As shown in an experiment presented in the article, when the proposed method is used, it is possible to relax the requirements for the quadrature down-converter filters. A random sampling device and an additional digital signal processing module is the price to pay for these relaxed...

Direct imaging and spectrophotometry of Comet P/Tempel 2

International Nuclear Information System (INIS)

Boehnhardt, H.; Beisser, K.; Vanysek, V.; Mueller, B.E.A.; Weiss, M.

1990-01-01

Both direct imaging and spectrophotometry of Comet P/Tempel 2 during May-November 1988 have led to a nuclear diameter determination of the order of about 10 km. Sekanina's (1987) spin-vector model for this comet is judged capable of qualitatively accounting for both the visual light curve of the comet during this period, which exhibited a steep increase perihelion despite the normal, moderate-decrease perihelion, and an asymmetric extension of the fanlike coma in the solar direction. The late activity onset, the possible constant visual brightness immediately afterward, and the deviation of the fan axis orientation from the predicted value in May 1988, may all furnish additional constraints for P/Tempel 2 nucleus modeling. 24 refs

Superlattices assembled through shape-induced directional binding

Science.gov (United States)

Lu, Fang; Yager, Kevin G.; Zhang, Yugang; Xin, Huolin; Gang, Oleg

2015-04-01

Organization of spherical particles into lattices is typically driven by packing considerations. Although the addition of directional binding can significantly broaden structural diversity, nanoscale implementation remains challenging. Here we investigate the assembly of clusters and lattices in which anisotropic polyhedral blocks coordinate isotropic spherical nanoparticles via shape-induced directional interactions facilitated by DNA recognition. We show that these polyhedral blocks--cubes and octahedrons--when mixed with spheres, promote the assembly of clusters with architecture determined by polyhedron symmetry. Moreover, three-dimensional binary superlattices are formed when DNA shells accommodate the shape disparity between nanoparticle interfaces. The crystallographic symmetry of assembled lattices is determined by the spatial symmetry of the block's facets, while structural order depends on DNA-tuned interactions and particle size ratio. The presented lattice assembly strategy, exploiting shape for defining the global structure and DNA-mediation locally, opens novel possibilities for by-design fabrication of binary lattices.

3D Volume Rendering and 3D Printing (Additive Manufacturing).

Science.gov (United States)

Katkar, Rujuta A; Taft, Robert M; Grant, Gerald T

2018-07-01

Three-dimensional (3D) volume-rendered images allow 3D insight into the anatomy, facilitating surgical treatment planning and teaching. 3D printing, additive manufacturing, and rapid prototyping techniques are being used with satisfactory accuracy, mostly for diagnosis and surgical planning, followed by direct manufacture of implantable devices. The major limitation is the time and money spent generating 3D objects. Printer type, material, and build thickness are known to influence the accuracy of printed models. In implant dentistry, the use of 3D-printed surgical guides is strongly recommended to facilitate planning and reduce risk of operative complications. Copyright © 2018 Elsevier Inc. All rights reserved.

75 FR 53611 - Direct Investment Surveys: BE-577, Quarterly Survey of U.S. Direct Investment Abroad-Direct...

Science.gov (United States)

2010-09-01

...] RIN 0691-AA75 Direct Investment Surveys: BE-577, Quarterly Survey of U.S. Direct Investment Abroad--Direct Transactions of U.S. Reporter With Foreign Affiliate AGENCY: Bureau of Economic Analysis, Commerce...-577 quarterly survey of U.S. direct investment abroad. The survey is conducted quarterly and obtains...

Differential contribution of visual and auditory information to accurately predict the direction and rotational motion of a visual stimulus.

Science.gov (United States)

Park, Seoung Hoon; Kim, Seonjin; Kwon, MinHyuk; Christou, Evangelos A

2016-03-01

Vision and auditory information are critical for perception and to enhance the ability of an individual to respond accurately to a stimulus. However, it is unknown whether visual and auditory information contribute differentially to identify the direction and rotational motion of the stimulus. The purpose of this study was to determine the ability of an individual to accurately predict the direction and rotational motion of the stimulus based on visual and auditory information. In this study, we recruited 9 expert table-tennis players and used table-tennis service as our experimental model. Participants watched recorded services with different levels of visual and auditory information. The goal was to anticipate the direction of the service (left or right) and the rotational motion of service (topspin, sidespin, or cut). We recorded their responses and quantified the following outcomes: (i) directional accuracy and (ii) rotational motion accuracy. The response accuracy was the accurate predictions relative to the total number of trials. The ability of the participants to predict the direction of the service accurately increased with additional visual information but not with auditory information. In contrast, the ability of the participants to predict the rotational motion of the service accurately increased with the addition of auditory information to visual information but not with additional visual information alone. In conclusion, this finding demonstrates that visual information enhances the ability of an individual to accurately predict the direction of the stimulus, whereas additional auditory information enhances the ability of an individual to accurately predict the rotational motion of stimulus.

Degree of multicollinearity and variables involved in linear dependence in additive-dominant models

Directory of Open Access Journals (Sweden)

Juliana Petrini

2012-12-01

Full Text Available The objective of this work was to assess the degree of multicollinearity and to identify the variables involved in linear dependence relations in additive-dominant models. Data of birth weight (n=141,567, yearling weight (n=58,124, and scrotal circumference (n=20,371 of Montana Tropical composite cattle were used. Diagnosis of multicollinearity was based on the variance inflation factor (VIF and on the evaluation of the condition indexes and eigenvalues from the correlation matrix among explanatory variables. The first model studied (RM included the fixed effect of dam age class at calving and the covariates associated to the direct and maternal additive and non-additive effects. The second model (R included all the effects of the RM model except the maternal additive effects. Multicollinearity was detected in both models for all traits considered, with VIF values of 1.03 - 70.20 for RM and 1.03 - 60.70 for R. Collinearity increased with the increase of variables in the model and the decrease in the number of observations, and it was classified as weak, with condition index values between 10.00 and 26.77. In general, the variables associated with additive and non-additive effects were involved in multicollinearity, partially due to the natural connection between these covariables as fractions of the biological types in breed composition.

Direct Regulation of Mitochondrial RNA Synthesis by Thyroid Hormone

Science.gov (United States)

Enríquez, José A.; Fernández-Silva, Patricio; Garrido-Pérez, Nuria; López-Pérez, Manuel J.; Pérez-Martos, Acisclo; Montoya, Julio

1999-01-01

We have analyzed the influence of in vivo treatment and in vitro addition of thyroid hormone on in organello mitochondrial DNA (mtDNA) transcription and, in parallel, on the in organello footprinting patterns at the mtDNA regions involved in the regulation of transcription. We found that thyroid hormone modulates mitochondrial RNA levels and the mRNA/rRNA ratio by influencing the transcriptional rate. In addition, we found conspicuous differences between the mtDNA dimethyl sulfate footprinting patterns of mitochondria derived from euthyroid and hypothyroid rats at the transcription initiation sites but not at the mitochondrial transcription termination factor (mTERF) binding region. Furthermore, direct addition of thyroid hormone to the incubation medium of mitochondria isolated from hypothyroid rats restored the mRNA/rRNA ratio found in euthyroid rats as well as the mtDNA footprinting patterns at the transcription initiation area. Therefore, we conclude that the regulatory effect of thyroid hormone on mitochondrial transcription is partially exerted by a direct influence of the hormone on the mitochondrial transcription machinery. Particularly, the influence on the mRNA/rRNA ratio is achieved by selective modulation of the alternative H-strand transcription initiation sites and does not require the previous activation of nuclear genes. These results provide the first functional demonstration that regulatory signals, such as thyroid hormone, that modify the expression of nuclear genes can also act as primary signals for the transcriptional apparatus of mitochondria. PMID:9858589

Future directions and emerging techniques for ISOL systems

International Nuclear Information System (INIS)

Talbert, W.L. Jr.; Bunker, M.E.

1986-01-01

The current status and future promise of ISOL systems are discussed, with emphasis on newly conceived experimental capabilities and interests. In addition to studies of nuclear structure using traditional or new on-line approaches, such as on-line nuclear orientation, the possibilities for studies with accelerated radioactive beams that have direct application to basic problems in materials science and astrophysics as well as to nuclear theory are pointed out. 43 refs., 3 figs., 1 tab

Critical issues and future directions in sintering science

International Nuclear Information System (INIS)

Brook, R.J.; Tuan, W.H.; Xue, L.A.

1988-01-01

The quality of available powders and the emphasis on direct microstructural observation have continued to improve the value of sintering studies for the processing of ceramics. Future concerns will relate to mechanisms for the correction of microstructural inhomogeneity so that pressureless processing of composites can be reliably achieved and to more systematic exploitation of dopants (sintering additives). These themes are illustrated using examples from the processing of alumina composites and doped barium titanate compositions

Direct Heat

Energy Technology Data Exchange (ETDEWEB)

Lienau, P J

1990-01-01

Potential resources and applications of earth heat in the form of geothermal energy are large. United States direct uses amount to 2,100 MWt thermal and worldwide 8,850 MWt above a reference temperature of 35 degrees Celsius. Space and district heating are the major direct uses of geothermal energy. Equipment employed in direct use projects is of standard manufacture and includes downhole and circulation pumps, transmission and distribution pipelines, heat exchangers and convectors, heat pumps and chillers. Direct uses of earth heat discussed are space and district heating, greenhouse heating and fish farming, process and industrial applications. The economic feasibility of direct use projects is governed by site specific factors such as location of user and resource, resource quality, system load factor and load density, as well as financing. Examples are presented of district heating in Klamath Falls, and Elko. Further developments of direct uses of geothermal energy will depend on matching user needs to the resource, and improving load factors and load density.

77 FR 72746 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel...

Science.gov (United States)

2012-12-06

... Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel Sulfur Programs AGENCY... Fuel Standard (``RFS'') program under section 211(o) of the Clean Air Act. The direct final rule also... marine diesel fuel produced by transmix processors, and the fuel marker requirements for 500 ppm sulfur...

Enhanced flux pinning in MOCVD-YBCO films through Zr additions : systematic feasibility studies.

Energy Technology Data Exchange (ETDEWEB)

Aytug, T.; Paranthaman, M.; Specht, E. D.; Zhang, Y.; Kim, K.; Zuev, Y. L.; Cantoni, C.; Goyal, A.; Christen, D. K.; Maroni, V. A.; Chen, Y.; Selvamanickam, V.; ORNL; SuperPower, Inc.

2010-01-01

Systematic effects of Zr additions on the structural and flux pinning properties of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films deposited by metal-organic chemical vapor deposition (MOCVD) have been investigated. Detailed characterization, conducted by coordinated transport, x-ray diffraction, scanning and transmission electron microscopy analyses, and imaging Raman microscopy have revealed trends in the resulting property/performance correlations of these films with respect to varying mole percentages (mol%) of added Zr. For compositions {le} 7.5 mol%, Zr additions lead to improved in-field critical current density, as well as extra correlated pinning along the c-axis direction of the YBCO films via the formation of columnar, self-assembled stacks of BaZrO{sub 3} nanodots.

Enhanced flux pinning in MOCVD-YBCO films through Zr additions: systematic feasibility studies

Energy Technology Data Exchange (ETDEWEB)

Aytug, T; Paranthaman, M; Specht, E D; Zhang, Y; Kim, K; Zuev, Y L; Cantoni, C; Goyal, A; Christen, D K [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Maroni, V A [Argonne National Laboratory, Argonne, IL 60439 (United States); Chen, Y; Selvamanickam, V, E-mail: aytugt@ornl.go [SuperPower, Incorporated, 450 Duane Avenue, Schenectady, NY 12304 (United States)

2010-01-15

Systematic effects of Zr additions on the structural and flux pinning properties of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films deposited by metal-organic chemical vapor deposition (MOCVD) have been investigated. Detailed characterization, conducted by coordinated transport, x-ray diffraction, scanning and transmission electron microscopy analyses, and imaging Raman microscopy have revealed trends in the resulting property/performance correlations of these films with respect to varying mole percentages (mol%) of added Zr. For compositions {<=}7.5 mol%, Zr additions lead to improved in-field critical current density, as well as extra correlated pinning along the c-axis direction of the YBCO films via the formation of columnar, self-assembled stacks of BaZrO{sub 3} nanodots.

Biodiesel production by direct transesterification of microalgal biomass with co-solvent.

Science.gov (United States)

Zhang, Yan; Li, Ya; Zhang, Xu; Tan, Tianwei

2015-11-01

In this study, a direct transesterification process using 75% ethanol and co-solvent was studied to reduce the energy consumption of lipid extraction process and improve the conversion yield of the microalgae biodiesel. The addition of a certain amount of co-solvent (n-hexane is most preferable) was required for the direct transesterification of microalgae biomass. With the optimal reaction condition of n-hexane to 75% ethanol volume ratio 1:2, mixed solvent dosage 6.0mL, reaction temperature 90°C, reaction time 2.0h and catalyst volume 0.6mL, the direct transesterification process of microalgal biomass resulted in a high conversion yield up to 90.02±0.55wt.%. Copyright © 2015 Elsevier Ltd. All rights reserved.

Direct UV-written broadband directional broadband planar waveguide couplers

DEFF Research Database (Denmark)

Olivero, Massimo; Svalgaard, Mikael

2005-01-01

We report the fabrication of broadband directional couplers by direct UV-writing. The fabrication process is shown to be beneficial, robust and flexible. The components are compact and show superior performance in terms of loss and broadband operation.......We report the fabrication of broadband directional couplers by direct UV-writing. The fabrication process is shown to be beneficial, robust and flexible. The components are compact and show superior performance in terms of loss and broadband operation....

Identification of flavour additives in tobacco products to develop a flavour library.

Science.gov (United States)

Krüsemann, Erna Jz; Visser, Wouter F; Cremers, Johannes Wjm; Pennings, Jeroen LA; Talhout, Reinskje

2018-01-01

This study combines chemical analysis and flavour descriptions of flavour additives used in tobacco products, and provides a starting point to build an extensive library of flavour components, useful for product surveillance. Headspace gas chromatography-mass spectrometry (GC-MS) was used to compare 22 commercially available tobacco products (cigarettes and roll-your-own) expected to have a characterising flavour and 6 commercially available products not expected to have a characterising flavour with 5 reference products (natural tobacco leaves and research cigarettes containing no flavour additives). The flavour components naturally present in the reference products were excluded from components present in commercially available products containing flavour additives. A description of the remaining flavour additives was used for categorisation. GC-MS measurements of the 33 tobacco products resulted in an overview of 186 chemical compounds. Of these, 144 were solely present in commercially available products. These 144 flavour additives were described using 62 different flavour descriptors extracted from flavour databases, which were categorised into eight groups largely based on the definition of characterising flavours from the European Tobacco Product Directive: fruit, spice, herb, alcohol, menthol, sweet, floral and miscellaneous. We developed a method to identify and describe flavour additives in tobacco products. Flavour additives consist of single flavour compounds or mixtures of multiple flavour compounds, and different combinations of flavour compounds can cause a certain flavour. A flavour library helps to detect flavour additives that are characteristic for a certain flavour, and thus can be useful for regulation of flavours in tobacco and related products. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

ACOG Committee Opinion No. 409: Direct-to-consumer marketing of genetic testing.

Science.gov (United States)

2008-06-01

Marketing of genetic testing, although similar to direct-to-consumer advertising of prescription drugs, raises additional concerns and considerations. These include issues of limited knowledge among patients and health care providers of available genetic tests, difficulty in interpretation of genetic testing results, lack of federal oversight of companies offering genetic testing, and issues of privacy and confidentiality. Until all of these considerations are addressed, direct or home genetic testing should be discouraged because of the potential harm of a misinterpreted or inaccurate result.

"Compacted" procedures for adults' simple addition: A review and critique of the evidence.

Science.gov (United States)

Chen, Yalin; Campbell, Jamie I D

2018-04-01

We review recent empirical findings and arguments proffered as evidence that educated adults solve elementary addition problems (3 + 2, 4 + 1) using so-called compacted procedures (e.g., unconscious, automatic counting); a conclusion that could have significant pedagogical implications. We begin with the large-sample experiment reported by Uittenhove, Thevenot and Barrouillet (2016, Cognition, 146, 289-303), which tested 90 adults on the 81 single-digit addition problems from 1 + 1 to 9 + 9. They identified the 12 very-small addition problems with different operands both ≤ 4 (e.g., 4 + 3) as a distinct subgroup of problems solved by unconscious, automatic counting: These items yielded a near-perfectly linear increase in answer response time (RT) yoked to the sum of the operands. Using the data reported in the article, however, we show that there are clear violations of the sum-counting model's predictions among the very-small addition problems, and that there is no real RT boundary associated with addends ≤4. Furthermore, we show that a well-known associative retrieval model of addition facts-the network interference theory (Campbell, 1995)-predicts the results observed for these problems with high precision. We also review the other types of evidence adduced for the compacted procedure theory of simple addition and conclude that these findings are unconvincing in their own right and only distantly consistent with automatic counting. We conclude that the cumulative evidence for fast compacted procedures for adults' simple addition does not justify revision of the long-standing assumption that direct memory retrieval is ultimately the most efficient process of simple addition for nonzero problems, let alone sufficient to recommend significant changes to basic addition pedagogy.

The effect of additives in silages of pure timothy and timothy mixed with red clover on chemical composition and in vitro rumen fermentation characteristics

NARCIS (Netherlands)

Hetta, M.; Cone, J.W.; Gustavsson, A.M.; Martinsson, K.

2003-01-01

The aim was to compare the effects of additives on direct cut silages of pure timothy and timothy mixed with tetraploid red clover. First and second growth cuts were ensiled during three consecutive years, 1994, 1995 and 1996, either without any additive or with the addition of formic acid, or

Model Additional Protocol

International Nuclear Information System (INIS)

Rockwood, Laura

2001-01-01

Since the end of the cold war a series of events has changed the circumstances and requirements of the safeguards system. The discovery of a clandestine nuclear weapons program in Iraq, the continuing difficulty in verifying the initial report of Democratic People's Republic of Korea upon entry into force of their safeguards agreement, and the decision of the South African Government to give up its nuclear weapons program and join the Treaty on the Non-Proliferation of Nuclear Weapons have all played a role in an ambitious effort by IAEA Member States and the Secretariat to strengthen the safeguards system. A major milestone in this effort was reached in May 1997 when the IAEA Board of Governors approved a Model Protocol Additional to Safeguards Agreements. The Model Additional Protocol was negotiated over a period of less than a year by an open-ended committee of the Board involving some 70 Member States and two regional inspectorates. The IAEA is now in the process of negotiating additional protocols, State by State, and implementing them. These additional protocols will provide the IAEA with rights of access to information about all activities related to the use of nuclear material in States with comprehensive safeguards agreements and greatly expanded physical access for IAEA inspectors to confirm or verify this information. In conjunction with this, the IAEA is working on the integration of these measures with those provided for in comprehensive safeguards agreements, with a view to maximizing the effectiveness and efficiency, within available resources, the implementation of safeguards. Details concerning the Model Additional Protocol are given. (author)

Synthesis of I-125 labeled photoaffinity rapamycin analogs

International Nuclear Information System (INIS)

Shu, A.Y.L.; Yamashita, D.S.; Holt, D.A.; Heys, J.R.

1996-01-01

Two no-carrier-added 125 I-labelled photoaffinity rapamycin analogs were prepared: 7-demethoxy-7-(4-azido-3- 125 I-benzyloxy) rapamycin and its C 28 -C 29 seco analog. The key reactions of the synthesis were substitution of the C 7 methoxyl of rapamycin with 4-azido-3-tributylstannylbenzyloxy group, exchange of tributyltin with 125 I using Na 125 I and Chloramine-T, and a ZnCl 2 mediated retro-Aldol cleavage of the C 28 -C 29 bond of rapamycin. (author)

Crystal Structure of a Trapped Catalytic Intermediate Suggests that Forced Atomic Proximity Drives the Catalysis of mIPS

OpenAIRE

Neelon, Kelly; Roberts, Mary F.; Stec, Boguslaw

2011-01-01

1-L-myo-inositol-phosphate synthase (mIPS) catalyzes the first step of the unique, de novo pathway of inositol biosynthesis. However, details about the complex mIPS catalytic mechanism, which requires oxidation, enolization, intramolecular aldol cyclization, and reduction, are not fully known. To gain further insight into this mechanism, we determined the crystal structure of the wild-type mIPS from Archaeoglobus fulgidus at 1.7 Å, as well as the crystal structures of three active-site mutant...

A Highly Efficient Method for Synthesis of Bisarylmethylidenes of Cyclic Ketones in [BMIm]Cl/NaOH System as New and Recyclable Catalyst

Directory of Open Access Journals (Sweden)

Shahrzad Javanshir

2014-03-01

Full Text Available An ionic liquid 1-Butyl-3-methylimidazoliumchloride[BMIm]Cl/sodium hydroxide system, was employed as a catalyst for the fast and one-pot crossed aldol-condensation of various aromatic aldehydes and cyclic ketones, to produce a variety of substituted α,α'-bis(benzylidene-cycloalkanones under neat conditions. This process is simple, efficient and environmentally benign and proceeds in high yield and short reaction times. The ionic liquid can be recycled for subsequent reactions without any appreciable loss of efficiency.

Antisolvent precipitation of novel xylitol-additive crystals to engineer tablets with improved pharmaceutical performance.

Science.gov (United States)

Kaialy, Waseem; Maniruzzaman, Mohammad; Shojaee, Saeed; Nokhodchi, Ali

2014-12-30

The purpose of this work was to develop stable xylitol particles with modified physical properties, improved compactibility and enhanced pharmaceutical performance without altering polymorphic form of xylitol. Xylitol was crystallized using antisolvent crystallization technique in the presence of various hydrophilic polymer additives, i.e., polyethylene glycol (PEG), polyvinylpyrrolidone (PVP) and polyvinyl alcohol (PVA) at a range of concentrations. The crystallization process did not influence the stable polymorphic form or true density of xylitol. However, botryoidal-shaped crystallized xylitols demonstrated different particle morphologies and lower powder bulk and tap densities in comparison to subangular-shaped commercial xylitol. Xylitol crystallized without additive and xylitol crystallized in the presence of PVP or PVA demonstrated significant improvement in hardness of directly compressed tablets; however, such improvement was observed to lesser extent for xylitol crystallized in the presence of PEG. Crystallized xylitols produced enhanced dissolution profiles for indomethacin in comparison to original xylitol. The influence of additive concentration on tablet hardness was dependent on the type of additive, whereas an increased concentration of all additives provided an improvement in the dissolution behavior of indomethacin. Antisolvent crystallization using judiciously selected type and concentration of additive can be a potential approach to prepare xylitol powders with promising physicomechanical and pharmaceutical properties. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of Bi Addition on the Microstructure and Mechanical Properties of Nanocrystalline Ag Coatings

Directory of Open Access Journals (Sweden)

Yuxin Wang

2017-08-01

Full Text Available In this study we investigated the effects of Bi addition on the microstructure and mechanical properties of an electrodeposited nanocrystalline Ag coating. Microstructural features were investigated with transmission electron microscopy (TEM. The results indicate that the addition of Bi introduced nanometer-scale Ag-Bi solid solution particles and more internal defects to the initial Ag microstructures. The anisotropic elastic-plastic properties of the Ag nanocrystalline coating with and without Bi addition were examined with nanoindentation experiments in conjunction with the recently-developed inverse method. The results indicate that the as-deposited nanocrystalline Ag coating contained high mechanical anisotropy. With the addition of 1 atomic percent (at% Bi, the anisotropy within Ag-Bi coating was very small, and yield strength of the nanocrystalline Ag-Bi alloy in both longitudinal and transverse directions were improved by over 100% compared to that of Ag. On the other hand, the strain-hardening exponent of Ag-Bi was reduced to 0.055 from the original 0.16 of the Ag coating. Furthermore, the addition of Bi only slightly increased the electrical resistivity of the Ag-Bi coating in comparison to Ag. Results of our study indicate that Bi addition is a promising method for improving the mechanical and physical performances of Ag coating for electrical contacts.

Influence of an additional ballast volume on a pulsed ICP discharge

International Nuclear Information System (INIS)

Bogdanov, E A; Jr, C A DeJoseph; Demidov, V I; Kudryavtsev, A A; Serditov, K Yu

2007-01-01

A spatial and temporal numerical simulation has been carried out of a pulsed (100% modulated), rf inductively coupled plasma discharge in argon, connected to an additional (ballast) diffusion chamber of much larger volume. It is demonstrated that during the active phase, the presence of the large ballast volume has a small impact on the parameters of the plasma in the smaller discharge chamber. In this case the plasma parameters in the discharge chamber can be estimated separately from the diffusion chamber by a standard method using the characteristic ambipolar diffusion time (for example, using a global model). However, during the afterglow phase, the situation is changed significantly. In the afterglow, the densities of charged particles in the discharge chamber become lower than in the large ballast chamber due to more rapid diffusion loss. As a result, the reverse of the active phase situation occurs, namely, the plasma does not flow from the small to the large chamber, but in the opposite direction, from diffusive to discharge volume, and both the plasma density gradient and the self-consistent ambipolar electric field in the small chamber change directions. This phenomenon leads to new effects in the discharge volume, in particular a decreasing rate of decay of densities of charged particles and electron temperature. Thus, in the afterglow the presence of a large additional ballast volume has a significant impact on the plasma transport. In this case, a simple treatment of the plasma in the discharge chamber in the framework of a spatially averaged model (for example, the global model) is inadequate

Monoclonal antibodies directed to E1 glycoprotein of rubella virus

International Nuclear Information System (INIS)

Umino, Y.; Sato, A.; Katow, S.; Matsuno, T.; Sugiura, A.

1985-01-01

We have prepared four monoclonal antibodies to rubella virus E1 glycoprotein. Three nonoverlapping antigenic sites were delineated on E1 protein by competitive binding assays. Antibodies binding to one site were characterized by high hemagglutination inhibition (HI) titer but poor neutralizing activity. The addition of antiglobulin conferred neutralizing activity. Antibodies directed to two other antigenic sites had modest hemolysis inhibition but little or no HI and neutralizing activities. The addition of antiglobulin markedly augmented HI activity but had little effect on neutralizing activity. Epitopes defined by three antibodies were conserved among four rubella virus strains examined. (Author)

Surface modification of biomaterials and biomedical devices using additive manufacturing.

Science.gov (United States)

Bose, Susmita; Robertson, Samuel Ford; Bandyopadhyay, Amit

2018-01-15

The demand for synthetic biomaterials in medical devices, pharmaceutical products and, tissue replacement applications are growing steadily due to aging population worldwide. The use for patient matched devices is also increasing due to availability and integration of new technologies. Applications of additive manufacturing (AM) or 3D printing (3DP) in biomaterials have also increased significantly over the past decade towards traditional as well as innovative next generation Class I, II and III devices. In this review, we have focused our attention towards the use of AM in surface modified biomaterials to enhance their in vitro and in vivo performances. Specifically, we have discussed the use of AM to deliberately modify the surfaces of different classes of biomaterials with spatial specificity in a single manufacturing process as well as commented on the future outlook towards surface modification using AM. It is widely understood that the success of implanted medical devices depends largely on favorable material-tissue interactions. Additive manufacturing has gained traction as a viable and unique approach to engineered biomaterials, for both bulk and surface properties that improve implant outcomes. This review explores how additive manufacturing techniques have been and can be used to augment the surfaces of biomedical devices for direct clinical applications. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Improved flux pinning behaviour in bulk MgB2 achieved by nano-SiO2 addition

International Nuclear Information System (INIS)

Rui, X F; Zhao, Y; Xu, Y Y; Zhang, L; Sun, X F; Wang, Y Z; Zhang, H

2004-01-01

Bulk MgB 2 with SiO 2 nanoparticles added has been synthesized using a simple solid-state reaction route. The lattice constant in the c direction increases with additive content due to a small amount of Si being doped into the lattice of the MgB 2 ; however, T c is almost fixed at 37.2 K. The addition of SiO 2 nanoparticles also improves the J c -H and H irr -T characteristics of MgB 2 when the additive content is lower than 7%. At 20 K and 1 T, J c for the sample with 7% additive content reaches 2.5 x 10 5 A cm -2 . Microstructural analysis reveals that a high density of MgSi 2 nanoparticles (10-50 nm) exists inside the MgB 2 grains, leading to the formation of a nanocomposite superconductor