WorldWideScience

Sample records for dioxide creep etude

  1. Creep of uranium dioxide: bending test and mechanical behaviour; Etude du fluage du dioxyde d'uranium: caracterisation par essais de flexion et modelisation mecanique

    Energy Technology Data Exchange (ETDEWEB)

    Colin, Ch

    2003-09-01

    These PhD work in the frame of Pellet-Cladding Interactions studies, in the fuel assemblies of nuclear plants. Electricite de France (EDF) must well demonstrate and insure the integrity of the cladding. For that purpose, the viscoplastic behaviour of the nuclear fuel has to be known and, if possible, controlled. This PhD work aimed to characterize the creep of uranium dioxide, in conditions of transient power regime. First, a literature survey on mechanical behaviour of UO{sub 2} revealed that the ceramic was essentially studied with compressive tests, and that its creep behaviour is characterized by two domains, depending on the stress level. To estimate the loadings in a fuel pellet, EDF and CEA developed specific global codes. A simulation during a power ramp allowed the order of magnitude of the loadings in the pellet to be determined (temperature, thermal gradients, strains, strain rate...). The stress calculation using a finite element simulation requires the identification of behaviour laws, able to describe the behaviour under small strains, low strain rates, and under tensile stresses. Starting from this observation, three point bending method has been chosen to test the uranium dioxide. As, for representativeness reasons, testing specimens cut in actual fuel pads was required in our study; a ten millimeters span has been used. For this study, a specific three-point testing device has been developed, that can tests specimens up to 2 000 C in a controlled atmosphere (Ar + 5% H{sub 2}). A special care has been taken for the measurement of the deflexion of the sample, which is measured using a laser beam, that allow an accuracy of {+-}2{mu}m to be reached at high temperature. Specimens with 0,5 to 1 mm thickness have been tested using this jig. A Norton's law describe, with respective stress exponent and activation energy values of 1.73 and 540 kJ.mole-1, provided a good description of the stationary creep rate. Then, the mechanical behaviour of the fuel

  2. Microstructural evolution of uranium dioxide following compression creep tests: An EBSD and image analysis study

    Energy Technology Data Exchange (ETDEWEB)

    Iltis, X., E-mail: xaviere.iltis@cea.fr [CEA, DEN, DEC, Cadarache, 13108 Saint-Paul-Lez-Durance (France); Gey, N. [Laboratoire d’Etude des Microstructures et de Mécanique des Matériaux (LEM3), CNRS UMR 7239, Université de Lorraine, Ile du Saulcy, 57045 Metz Cedex 1 (France); Cagna, C. [CEA, DEN, DEC, Cadarache, 13108 Saint-Paul-Lez-Durance (France); Hazotte, A. [Laboratoire d’Etude des Microstructures et de Mécanique des Matériaux (LEM3), CNRS UMR 7239, Université de Lorraine, Ile du Saulcy, 57045 Metz Cedex 1 (France); Sornay, Ph. [CEA, DEN, DEC, Cadarache, 13108 Saint-Paul-Lez-Durance (France)

    2015-01-15

    Highlights: • Image analysis and EBSD are performed on creep tested UO{sub 2} pellets. • Development of intergranular voids, with increasing strain, is quantified. • EBSD evidences a sub-structuration process within the grains and quantifies it. • Creep mechanisms are discussed on the basis of these results. - Abstract: Sintered UO{sub 2} pellets with relatively large grains (∼25 μm) are tested at 1500 °C under a compressive stress of 50 MPa, at different deformation levels up to 12%. Electron Back Scattered Diffraction (EBSD) is used to follow the evolution, with deformation, of grains (size, shape, orientation) and sub-grains. Image analyses of SEM images are performed to characterize emergence of a population of micron size voids. For the considered microstructure and test conditions, the results show that the deformation process of UO{sub 2} globally corresponds to grain boundary sliding, partly accommodated by a dislocational creep within the grains, leading to a highly sub-structured state.

  3. Folds and Etudes

    Science.gov (United States)

    Bean, Robert

    2007-01-01

    In this article, the author talks about "Folds" and "Etudes" which are images derived from anonymous typing exercises that he found in a used copy of "Touch Typing Made Simple". "Etudes" refers to the musical tradition of studies for a solo instrument, which is a typewriter. Typing exercises are repetitive attempts to type words and phrases…

  4. Physical mechanisms of creep

    International Nuclear Information System (INIS)

    Rojtburd, A.L.

    1976-01-01

    The review is devoted to microscopic theories of creep in the range of temperatures where it is determined by self-diffusion. Interactions of vacancies with dislocations resulting in creeping over the latter are considered in detail. It is demonstrated that even at high temperatures the creep is determined by the process which includes creeping over and sliding of dislocations. Specific features of the description of polycrystal creep are considered

  5. FINE-GRAINEDCELLULAR CONCRETE CREEP ANALYSIS TECHNIQUE WITH CONSIDERATION FORCARBONATION

    Directory of Open Access Journals (Sweden)

    M. A. Gaziev

    2015-01-01

    Full Text Available The article considers the creep and creep deformation analysis technique in fine-grainedcellular concrete with consideration for carbonation and assurance requirements for the repairing properties and seismic stability. The procedure for determining the creep of fine-grainedcellular concrete is proposed with account of its carbonationby atmospheric carbon dioxide. It has been found theoretically and experimentally that the proposed technique allows obtaining reproducible results and can be recommended for creep determination of fine-grainedcellular concretes, including repairingones, taking into account their carbonation.

  6. Contribution to the study of the microstructure of uranium dioxide (1962); Contribution a l'etude de la microstructure du dioxyde d'uranium (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Porneuf, A. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1960-05-15

    The microstructure of sintered uranium dioxide is studied in relation with several parameters, specially the sintering temperatures and atmospheres. The external surface and the internal microstructure of the sintered are examined, using fractography and ceramography. Various techniques for preparing surfaces (mechanical and electrolytic polishing) and for revealing the structure (chemical and anodic attack, ionic bombardment oxidation) have been experienced and compared. Patterns similar to those revealed in metals and probably related with interactions between dislocations and vacancies have been observed. (author) [French] La microstructure de frittes d'oxyde d'uranium est etudiee en fonction de divers parametres, en particulier de la temperature et de l'atmosphere de frittage, par examen de la surface externe des frittes, puis de leur microstructure interne (fractographie, ceramographie). Differentes techniques de preparation des surfaces (polissage mecanique ou electrolytique) et de revelation de la structure (attaque chimique ou anodique, bombardement ionique, oxydation preferentielle) ont ete experimentees et comparees. Des figures comparables a celles revelees dans les metaux et liees probablement a des interactions entre dislocations et lacunes ont ete observees. (auteur)

  7. Creep of crystals

    International Nuclear Information System (INIS)

    Poirier, J.-P.

    1988-01-01

    Creep mechanisms for metals, ceramics and rocks, effect of pressure and temperature on deformation processes are considered. The role of crystal defects is analysed, different models of creep are described. Deformation mechanisms maps for different materials are presented

  8. Simultaneous consolidation and creep

    DEFF Research Database (Denmark)

    Krogsbøll, Anette

    1997-01-01

    Materials that exhibit creep under constant effective stress typically also show rate dependent behavior. The creep deformations and the rate sensitive behavior is very important when engineering and geological problems with large time scales are considered. When stress induced compaction (consol...... (consolidation) is retarded by slow drainage of excess pore pressure it is expected that consolidation and creep occur simultaneously. A constitutive model adressing the problems of rate sensitive behavior and simultaneous consolidation and creep is presented....

  9. Creep in ceramics

    CERN Document Server

    Pelleg, Joshua

    2017-01-01

    This textbook is one of its kind, since there are no other books on Creep in Ceramics. The book consist of two parts: A and B. In part A general knowledge of creep in ceramics is considered, while part B specifies creep in technologically important ceramics. Part B covers creep in oxide ceramics, carnides and nitrides. While covering all relevant information regarding raw materials and characterization of creep in ceramics, the book also summarizes most recent innovations and developments in this field as a result of extensive literature search.

  10. Irradiation creep of graphite

    International Nuclear Information System (INIS)

    Kennedy, C.R.

    1990-01-01

    Displacement damage of graphite by neutron irradiation causes graphite to change dimensions. This dimensional instability requires careful attention when graphite is used as as moderator and reflector material in nuclear devices. Natural gradients in flux and temperature result in time-varying differential growth generating stresses similar to thermal stresses with an ever increasing temperature gradient. Graphite, however, does have the ability to creep under irradiation, allowing the stress intensity to relax below the fracture strength of the material. Creep strain also serves to average the radiation-induced strains, thus contributing to the stability of the core. As the dimensional instability is a function of temperature, so are the creep characteristics of graphite, and it is of interest to generalize the available data for extension to more extreme conditions of fluence and temperature. Irradiation creep of graphite is characterized by two stages of creep; a primary stage that saturates with time and a secondary stage that is generally assumed to be linear and constant with time. Virtually all past studies have not considered primary creep in detail primarily because there is limited available data at the very low fluences required to saturate primary creep. It is the purpose of this study to carefully examine primary creep in detail over the irradiation temperature range of 150 to 1000 degree C. These studies also include the combined effects of creep, differential growth, and structural changes in graphite by irradiation. 3 refs., 5 figs

  11. Measuring irradiation creep

    International Nuclear Information System (INIS)

    Pelah, I.

    1981-03-01

    Simulation of fusion-neutron induced damage by beams of light ions is discussed. It is suggested that accelerated creep measurements to determine ''end of life'' of materials may be done by the application of thermal treatment and thermal creep measurements. (author)

  12. Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steel weldments; Etude experimentale et modelisation, du comportement, de l'endommagement et de la rupture en fluage a haute temperature de joint soudes en acier 9Cr1Mo-NbV

    Energy Technology Data Exchange (ETDEWEB)

    Gaffard, V

    2004-12-15

    Chromium martensitic stainless steels are under development since the 70's with the prospect of using them as structural components in thermal and nuclear power plants. The modified 9Cr1Mo-NbV steel is already used, especially in England and Japan, as a material for structural components in thermal power plants where welding is a commonly used joining technique. New generations of chromium martensitic stainless steels with improved mechanical properties for high pressure and temperature use are currently under development. However, observations of several in-service premature failures of welded components in 9Cr1Mo-NbV steel, outline a strong need for understanding the high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steels and weldments. The present study aimed at experimentally determining and then modelling the high temperature creep flow and damage behaviour of both 9Cr1Mo-NbV steels and weldments (typically in the temperature range from 450 C to 650 C). The base metal was first studied as the reference material. It was especially evidenced that tempered chromium martensitic steels exhibit a change in both creep flow and damage behaviour for long term creep exposure. As a consequence, the classically performed extrapolation of 1,000 hours creep data to 100,000 hours creep lifetime predictions might be very hazardous. Based on experimental observations, a new model, integrating and coupling multiple creep flow and damage mechanisms, was developed in the framework of the mechanics of porous media. It was then successfully used to represent creep flow and damage behaviour of the base metal from high to low stress levels even for complex multiaxial loading conditions. Although the high temperature creep properties of the base metal are quite good, the occurrence of premature failure in weldments in high temperature creep conditions largely focused the attention of the scientific community. The lower creep strength of the weld component was also

  13. Spherical Indentation Techniques for Creep Property Evaluation Considering Transient Creep

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Dongkyu; Kim, Minsoo; Lee, Hyungyil [Sogang Univ., Seoul, (Korea, Republic of); Lee, Jin Haeng [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-11-15

    Creep through nanoindentations has attracted increasing research attention in recent years. Many studies related to indentation creep tests, however, have simply focused on the characteristics of steady-state creep, and there exist wide discrepancies between the uniaxial test and the indentation test. In this study, we performed a computational simulation of spherical indentations, and we proposed a method for evaluating the creep properties onsidering transient creep. We investigated the material behavior with variation of creep properties and expressed it using regression equations for normalized variables. We finally developed a program to evaluate the creep properties considering transient creep. By using the proposed method, we successfully obtained creep exponents with an average error less than 1.1 and creep coefficients with an average error less than 2.3 from the load-depth curve.

  14. Spherical Indentation Techniques for Creep Property Evaluation Considering Transient Creep

    International Nuclear Information System (INIS)

    Lim, Dongkyu; Kim, Minsoo; Lee, Hyungyil; Lee, Jin Haeng

    2013-01-01

    Creep through nanoindentations has attracted increasing research attention in recent years. Many studies related to indentation creep tests, however, have simply focused on the characteristics of steady-state creep, and there exist wide discrepancies between the uniaxial test and the indentation test. In this study, we performed a computational simulation of spherical indentations, and we proposed a method for evaluating the creep properties onsidering transient creep. We investigated the material behavior with variation of creep properties and expressed it using regression equations for normalized variables. We finally developed a program to evaluate the creep properties considering transient creep. By using the proposed method, we successfully obtained creep exponents with an average error less than 1.1 and creep coefficients with an average error less than 2.3 from the load-depth curve

  15. Creep properties of discontinuous fibre composites with partly creeping fibres

    International Nuclear Information System (INIS)

    Bilde-Soerensen, J.B.; Lilholt, H.

    1977-05-01

    In a previous report (RISO-M-1810) the creep properties of discontinuous fibre composites with non-creeping fibres were analyzed. In the present report this analysis is extended to include the case of discontinuous composites with partly creeping fibres. It is shown that the creep properties of the composite at a given strain rate, epsilonsub(c), depend on the creep properties of the matrix at a strain rate higher than epsilonsub(c), and on the creep properties of the fibres at epsilonsub(c). The composite creep law is presented in a form which permits a graphical determination of the composite creep curve. This can be constructed on the basis of the matrix and the fibre creep curves by vector operations in a log epsilon vs. log sigma diagram. The matrix contribution to the creep strength can be evaluated by a simple method. (author)

  16. Creep in generation IV nuclear applications

    Energy Technology Data Exchange (ETDEWEB)

    Rissanen, L. (VTT Technical Research Centre of Finland, Espoo (Finland))

    2010-05-15

    Nuclear power has an important role in fulfilling the world's growing energy needs and reducing the carbon dioxide emission. Six new, innovative nuclear energy systems have been identified and selected for further development by the international Generation Four International Forum (GIF). These generation four (Gen IV) nuclear energy systems include a variety of reactor, energy conversion and fuel cycle technologies. The successful development and deployment of these largely depend on the performance and reliability of the available structural materials. These potential materials need to sustain their mechanical properties up to high temperatures, high neutron doses and corrosive environments of the new or enhanced types of coolants. Current knowledge on material properties, material-coolant interaction and especially material degradation processes in these new environments are limited. This paper gives an overview of the Gen IV material issues with special emphasis on European design of supercritical light water reactor concept high performance light water reactor (HPLWR). The challenges for the structural materials and the components most likely to suffer from creep and creep-irradiation are highlighted. Some results from relatively short term creep testing in supercritical water are presented for AISI 316NG, 347H and 1.4970 steels. The 1.4970 steel was superior in creep and oxidation resistance (orig.)

  17. Irradiation Creep in Graphite

    Energy Technology Data Exchange (ETDEWEB)

    Ubic, Rick; Butt, Darryl; Windes, William

    2014-03-13

    An understanding of the underlying mechanisms of irradiation creep in graphite material is required to correctly interpret experimental data, explain micromechanical modeling results, and predict whole-core behavior. This project will focus on experimental microscopic data to demonstrate the mechanism of irradiation creep. High-resolution transmission electron microscopy should be able to image both the dislocations in graphite and the irradiation-induced interstitial clusters that pin those dislocations. The team will first prepare and characterize nanoscale samples of virgin nuclear graphite in a transmission electron microscope. Additional samples will be irradiated to varying degrees at the Advanced Test Reactor (ATR) facility and similarly characterized. Researchers will record microstructures and crystal defects and suggest a mechanism for irradiation creep based on the results. In addition, the purchase of a tensile holder for a transmission electron microscope will allow, for the first time, in situ observation of creep behavior on the microstructure and crystallographic defects.

  18. Biaxial Creep Specimen Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    JL Bump; RF Luther

    2006-02-09

    This report documents the results of the weld development and abbreviated weld qualification efforts performed by Pacific Northwest National Laboratory (PNNL) for refractory metal and superalloy biaxial creep specimens. Biaxial creep specimens were to be assembled, electron beam welded, laser-seal welded, and pressurized at PNNL for both in-pile (JOYO reactor, O-arai, Japan) and out-of-pile creep testing. The objective of this test campaign was to evaluate the creep behavior of primary cladding and structural alloys under consideration for the Prometheus space reactor. PNNL successfully developed electron beam weld parameters for six of these materials prior to the termination of the Naval Reactors program effort to deliver a space reactor for Project Prometheus. These materials were FS-85, ASTAR-811C, T-111, Alloy 617, Haynes 230, and Nirnonic PE16. Early termination of the NR space program precluded the development of laser welding parameters for post-pressurization seal weldments.

  19. Biaxial Creep Specimen Fabrication

    International Nuclear Information System (INIS)

    JL Bump; RF Luther

    2006-01-01

    This report documents the results of the weld development and abbreviated weld qualification efforts performed by Pacific Northwest National Laboratory (PNNL) for refractory metal and superalloy biaxial creep specimens. Biaxial creep specimens were to be assembled, electron beam welded, laser-seal welded, and pressurized at PNNL for both in-pile (JOYO reactor, O-arai, Japan) and out-of-pile creep testing. The objective of this test campaign was to evaluate the creep behavior of primary cladding and structural alloys under consideration for the Prometheus space reactor. PNNL successfully developed electron beam weld parameters for six of these materials prior to the termination of the Naval Reactors program effort to deliver a space reactor for Project Prometheus. These materials were FS-85, ASTAR-811C, T-111, Alloy 617, Haynes 230, and Nirnonic PE16. Early termination of the NR space program precluded the development of laser welding parameters for post-pressurization seal weldments

  20. Seismic Creep, USA Images

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Seismic creep is the constant or periodic movement on a fault as contrasted with the sudden rupture associated with an earthquake. It is a usually slow deformation...

  1. Limit analysis via creep

    International Nuclear Information System (INIS)

    Taroco, E.; Feijoo, R.A.

    1981-07-01

    In this paper it is presented a variational method for the limit analysis of an ideal plastic solid. This method has been denominated as Modified Secundary Creep and enables to find the collapse loads through a minimization of a functional and a limit process. Given an ideal plastic material it is shown how to determinate the associated secundary creep constitutive equation. Finally, as an application, it is found the limit load in an pressurized von Mises rigid plastic sphere. (Author) [pt

  2. Topical Problems and Applications of Creep Theory

    Science.gov (United States)

    Altenbach, H.

    2003-06-01

    A historical review of achievements in creep theory is given. Primary attention is focused on the phenomenological approach. Different constitutive equations are discussed for primary and secondary creep as well as for creep with damage. New creep problems are examined

  3. ORNL irradiation creep facility

    International Nuclear Information System (INIS)

    Reiley, T.C.; Auble, R.L.; Beckers, R.M.; Bloom, E.E.; Duncan, M.G.; Saltmarsh, M.J.; Shannon, R.H.

    1980-09-01

    A machine was developed at ORNL to measure the rates of elongation observed under irradiation in stressed materials. The source of radiation is a beam of 60 MeV alpha particles from the Oak Ridge Isochronous Cyclotron (ORIC). This choice allows experiments to be performed which simulate the effects of fast neutrons. A brief review of irradiation creep and experimental constraints associated with each measurement technique is given. Factors are presented which lead to the experimental choices made for the Irradiation Creep Facility (ICF). The ICF consists of a helium-filled chamber which houses a high-precision mechanical testing device. The specimen to be tested must be thermally stabilized with respect to the temperature fluctuations imposed by the particle beam which passes through the specimen. Electrical resistance of the specimen is the temperature control parameter chosen. Very high precision in length measurement and temperature control are required to detect the small elongation rates relevant to irradiation creep in the test periods available (approx. 1 day). The apparatus components and features required for the above are presented in some detail, along with the experimental procedures. The damage processes associated with light ions are discussed and displacement rates are calculated. Recent irradiation creep results are given, demonstrating the suitability of the apparatus for high resolution experiments. Also discussed is the suitability of the ICF for making high precision thermal creep measurements

  4. Predicting creep strengths and lifetimes of creep resistant engineering alloys

    Science.gov (United States)

    Zhao, Yanrong; Yao, Hongpeng; Song, Xinli; Jia, Juan; Xiang, Zhidong

    2018-01-01

    The physical basis for predicting the long-term creep strengths and lifetimes at application temperatures using creep parameters determined from short-term creep tests is investigated for complex creep resistant engineering alloys. It is shown that the seemingly unpredictable stress and temperature dependence of minimum creep rate of such alloys can be rationalised using an approach based on the new power law creep equation that incorporate the tensile strength. This is demonstrated using the tensile and creep data measured for two completely different types of alloys: steel 11Cr-2W-0.4Mo-1Cu-Nb-V and Ni base superalloy 15Cr-28Co-4Mo-2.5Ti-3Al. For both alloys, the stress exponent n determined does not depend on temperature and activation energy of creep does not depend on stress. Consequently, it becomes possible to use the new power law creep equation in combination with the Monkman-Grant relationship to predict the long term creep rupture strengths and lifetimes and microstructure stability of the two alloys from short term creep test data. The implications of the results for creep mechanism identification and future microstructure analysis are discussed.

  5. Creep of fibrous composite materials

    DEFF Research Database (Denmark)

    Lilholt, Hans

    1985-01-01

    Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions to the cr......Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions...... such as Ni + W-fibres, high temperature materials such as Ni + Ni3Al + Cr3C2-fibres, and medium temperature materials such as Al + SiC-fibres. For the first two systems reasonable consistency is found for the models and the experiments, while for the third system too many unquantified parameters exist...

  6. Micro creep mechanisms of tungsten

    International Nuclear Information System (INIS)

    Levoy, R.; Hugon, I.; Burlet, H.; Baillin, X.; Guetaz, L.

    2000-01-01

    Due to its high melting point (3410 deg C), tungsten offers good mechanical properties at elevated temperatures for several applications in non-oxidizing environment. The creep behavior of tungsten is well known between 1200 and 2500 deg C and 10 -3 to 10 -1 strain. However, in some applications when dimensional stability of components is required, these strains are excessive and it is necessary to know the creep behavior of the material for micro-strains (between 10 -4 and 10 -6 ). Methods and devices used to measure creep micro-strains are presented, and creep equations (Norton and Chaboche laws) were developed for wrought, annealed and recrystallized tungsten. The main results obtained on tungsten under low stresses are: stress exponent 1, symmetry of micro-strains in creep-tension and creep-compression, inverse creep (threshold stress), etc. TEM, SEM and EBSD studies allow interpretation of the micro-creep mechanism of tungsten under low stresses and low temperature (∼0.3 K) like the Harper-Dorn creep. In Harper-Dorn creep, micro-strains are associated with the density and the distribution of dislocations existing in the crystals before creep. At 975 deg C, the initial dislocation structure moves differently whether or not a stress is applied. To improve the micro-creep behavior of tungsten, a heat treatment is proposed to create the optimum dislocation structure. (authors)

  7. Consistent creep and rupture properties for creep-fatigue evaluation

    International Nuclear Information System (INIS)

    Schultz, C.C.

    1978-01-01

    The currently accepted practice of using inconsistent representations of creep and rupture behaviors in the prediction of creep-fatigue life is shown to introduce a factor of safety beyond that specified in current ASME Code design rules for 304 stainless steel Class 1 nuclear components. Accurate predictions of creep-fatigue life for uniaxial tests on a given heat of material are obtained by using creep and rupture properties for that same heat of material. The use of a consistent representation of creep and rupture properties for a mininum strength heat is also shown to provide adequate predictions. The viability of using consistent properties (either actual or those of a minimum heat) to predict creep-fatigue life thus identifies significant design uses for the results of characterization tests and improved creep and rupture correlations

  8. Analysis of indentation creep

    Science.gov (United States)

    Don S. Stone; Joseph E. Jakes; Jonathan Puthoff; Abdelmageed A. Elmustafa

    2010-01-01

    Finite element analysis is used to simulate cone indentation creep in materials across a wide range of hardness, strain rate sensitivity, and work-hardening exponent. Modeling reveals that the commonly held assumption of the hardness strain rate sensitivity (mΗ) equaling the flow stress strain rate sensitivity (mσ...

  9. Creep behavior of submarine sediments

    Science.gov (United States)

    Silva, Armand J.; Booth, J.S.

    1984-01-01

    A series of experiments on drained creep of marine sediment indicates that strength degradation results from the creep process, which implies an associated reduction in slope stability. Furthermore, the highest creep potential of a sediment may be at its preconsolidation stress. Results from the experiments on samples from Georges Bank continental slope were also used in conjunction with a preliminary theoretical model to predict creep displacements. For the case illustrated in this report, steep slopes (>20??) and thick sections (>30 m) give rise to substantial creep and probable creep rupture; as angles or thicknesses decrease, displacements rapidly become negligible. Creep may be a significant geologic process on many marine slopes. Not only can it cause major displacements of surface sediment, but it may also be the precursor to numerous slope failures. ?? 1985 Springer-Verlag New York Inc.

  10. Creep behaviour and creep mechanisms of normal and healing ligaments

    Science.gov (United States)

    Thornton, Gail Marilyn

    Patients with knee ligament injuries often undergo ligament reconstructions to restore joint stability and, potentially, abate osteoarthritis. Careful literature review suggests that in 10% to 40% of these patients the graft tissue "stretches out". Some graft elongation is likely due to creep (increased elongation of tissue under repeated or sustained load). Quantifying creep behaviour and identifying creep mechanisms in both normal and healing ligaments is important for finding clinically relevant means to prevent creep. Ligament creep was accurately predicted using a novel yet simple structural model that incorporated both collagen fibre recruitment and fibre creep. Using the inverse stress relaxation function to model fibre creep in conjunction with fibre recruitment produced a superior prediction of ligament creep than that obtained from the inverse stress relaxation function alone. This implied mechanistic role of fibre recruitment during creep was supported using a new approach to quantify crimp patterns at stresses in the toe region (increasing stiffness) and linear region (constant stiffness) of the stress-strain curve. Ligament creep was relatively insensitive to increases in stress in the toe region; however, creep strain increased significantly when tested at the linear region stress. Concomitantly, fibre recruitment was evident at the toe region stresses; however, recruitment was limited at the linear region stress. Elevating the water content of normal ligament using phosphate buffered saline increased the creep response. Therefore, both water content and fibre recruitment are important mechanistic factors involved in creep of normal ligaments. Ligament scars had inferior creep behaviour compared to normal ligaments even after 14 weeks. In addition to inferior collagen properties affecting fibre recruitment and increased water content, increased glycosaminoglycan content and flaws in scar tissue were implicated as potential mechanisms of scar creep

  11. CHOICE THEORY OF CREEP DEFORMATION FOR EVALUATION OF LONG FINE-GRAINED AUTOCLAVED AERATED CONCRETE IN VIEW OF FACTORS CARBONIZATION

    Directory of Open Access Journals (Sweden)

    D. K-S. Bataev

    2015-01-01

    Full Text Available Experimental data on the effect of the age of autoclaved aerated concrete with and without carbonation factor to change its physical and mechanical characteristics, as well as by the amount of creep deformation and degree of reversibility. It was found that the solution of applied problems creep theory for structures of autoclaved aerated concrete, in accordance with their carbonation from the effects of atmospheric carbon dioxide, it is necessary to use the theory of elastic-creeping body on the basis of function creep measures in the form proposed by prof. S.V. Alexandrovsky. 

  12. Reassembling Surveillance Creep

    DEFF Research Database (Denmark)

    Bøge, Ask Risom; Lauritsen, Peter

    2017-01-01

    We live in societies in which surveillance technologies are constantly introduced, are transformed, and spread to new practices for new purposes. How and why does this happen? In other words, why does surveillance “creep”? This question has received little attention either in theoretical...... development or in empirical analyses. Accordingly, this article contributes to this special issue on the usefulness of Actor-Network Theory (ANT) by suggesting that ANT can advance our understanding of ‘surveillance creep’. Based on ANT’s model of translation and a historical study of the Danish DNA database......, we argue that surveillance creep involves reassembling the relations in surveillance networks between heterogeneous actors such as the watchers, the watched, laws, and technologies. Second, surveillance creeps only when these heterogeneous actors are adequately interested and aligned. However...

  13. Study and simulation of the behaviour under irradiation of helium in uranium dioxide; Etude et modelisation du comportement sous irradiation de l'helium dans le dioxyde d'uranium

    Energy Technology Data Exchange (ETDEWEB)

    Martin, G

    2007-06-15

    Large quantities of helium are produced from {alpha}-decay of actinides in nuclear fuels during its in-pile operating and its storage. It is important to understand the behaviour of helium in these matrix in order to well simulate the evolution and the resistance of the fuel element. During this thesis, we have used nuclear reaction analyses (NRA) to follow the evolution of the helium implanted in polycrystalline and monocrystalline uranium dioxide (UO{sub 2}). An experimental rig was developed to follow the on-line helium release in UO{sub 2} and the evolution of {sup 3}He profiles as a function of annealing temperature. An automated procedure taking into account the evolution of the depth resolution was developed. Analyses performed with a nuclear microprobe allowed to characterise the spatial distribution of helium at the grain scale and to study the influence of the sample microstructure on the helium migration. This work put into evidence the particular role of grain boundaries and irradiation defects in the helium release process. The analyse of experimental results with a diffusion model corroborates these interpretations. It allowed to determine quantitatively physical properties that characterise the helium behaviour in uranium dioxide (diffusion coefficient, activation energy..). (author)

  14. Creep in sodium

    International Nuclear Information System (INIS)

    Charnock, W.; Cordwell, J.E.

    1978-03-01

    Available information on the creep of austenitic, ferritic and Alloy-800 type steels in liquid sodium is critically reviewed. Creep properties of stainless steels can be affected by element transfer and corrosion. At reactor structural component temperatures environmental effects are likely to be less important than changes due to thermal ageing. At high clad temperatures (700 0 C) decarburisation may cause the loss of strength and ductility in unstabilised steels while cavity formation may cause embrittlement in stabilised steels. The properties of Alloy 800 are, in some experiments, found to deteriorate while in others they are enhanced. This may be a consequence of the metallurgical complexity of the material or arise from the nature of the various techniques employed. Low alloy ferritic steels tend to decarburise in sodium at temperatures greater than 500 0 C and this leads to loss of strength and an increase in ductility. High alloy ferritics are immune to this effect and appear to be able to tolerate a degree of carburisation. Although intergranular cracking may be enhanced in liquid sodium the mechanical consequences are not significant and evidence for the existence of an embrittlement effect not associated with element transfer or corrosion is weak. Stress and strain may enhance element transfer at crack tips. However in real cracks the gettering or supply action of the crack faces conditions the chemistry of the cracks in sodium and protects the crack tip from element transfer. Thus creep crack extension rates should be independent of changes in bulk coolant chemistry. (author)

  15. Creep of fibrous composite materials

    DEFF Research Database (Denmark)

    Lilholt, Hans

    1985-01-01

    Models are presented for the creep behaviour of fibrous composite materials with aligned fibres. The models comprise both cases where the fibres remain rigid in a creeping matrix and cases where the fibres are creeping in a creeping matrix. The treatment allows for several contributions...... to the creep strength of composites. The advantage of combined analyses of several data sets is emphasized and illustrated for some experimental data. The analyses show that it is possible to derive creep equations for the (in situ) properties of the fibres. The experiments treated include model systems...... such as Ni + W-fibres, high temperature materials such as Ni + Ni3Al + Cr3C2-fibres, and medium temperature materials such as Al + SiC-fibres. For the first two systems reasonable consistency is found for the models and the experiments, while for the third system too many unquantified parameters exist...

  16. Numerical algorithms in secondary creep

    International Nuclear Information System (INIS)

    Feijoo, R.A.; Taroco, E.

    1980-01-01

    The problem of stationary creep is presented as well as its variational formulation, when weak constraints are established, capable of assuring one single solution. A second, so-called elasto-creep problem, is further analysed, together with its variational formulation. It is shown that its stationary solution coincides with that of the stationary creep and the advantages of this formulation with respect to the former one is emphasized. Some numerical applications showing the efficiency of the method propesed are finally presented [pt

  17. Thermal ratcheting and creep damage

    International Nuclear Information System (INIS)

    Clement, G.; Cousseran, P.; Roche, R.L.

    1983-01-01

    Several proposals have been made to assist adesigners with thermal ratcheting in the creep range, the more known has been made by O'DONNELL and POROWSKY. Unfortunately these methods are not validated by experiments, and they take only inelastic distortion into consideration as creep effects. The aim of the work presented here is to correct these deficiencies - in providing an experimental basis to ratcheting analysis rules in the creep range, - in considering the effect of cyclic straining (like cyclic thermal stresses) on the time to rupture by creep. Experimental tests have been performed on austenitic stainless steel at 650 0 C for the first item. Results of these tests and results available in the open literature have been used to built a practical rule of ratcheting analysis. This rule giving a conservative value of the creep distortion, is based on the concept of effective primary stress which is an amplification of the primary stress really applied. Concerning the second point (time to rupture), it was necessary to obtain real creep rupture and not instability. According to the proposal of Pr LECKIE, tests were performed on specimens made out of copper, and of aluminium alloys at temperatures between 150 0 C and 300 0 C. With such materials creep rupture is obtained without necking. Experimental tests show that cyclic straining reduces the time to creep rupture under load controlled stress. Caution must be given to the designer: cyclic thermal stress can lead to premature creep rupture. (orig./GL)

  18. Carbon dioxide seasonal cycle in the sea euphotic zone - a study in the Sargasso Sea; Cycle saisonnier du CO{sub 2} dans la zone euphotique marine - une etude dans la mer des sargasses

    Energy Technology Data Exchange (ETDEWEB)

    Marchal, O.

    1996-05-28

    Between 1750 and 1990, the human activities (mainly fossil carbon combustion and deforestation) have lead to an increase of the CO{sub 2} concentration in the atmosphere. Nevertheless, the carbon dioxide actively takes part to the greenhouse effect and then to the energetic balance of the climatic system. The study which is carried out consists of the forecasting of the CO{sub 2} future concentrations in the atmosphere (from 10, 100 years). The chosen site (BATS: Bermuda Atlantic Time-series Study) is located in the Sargasso Sea. The factors leading to seasonal variations have been determined. Several bio-geochemical models have been developed in order to on the one hand simulate the seasonal dynamics of the mixture layer observed in the Bats site and on the other hand explain the main characteristics of the observed phytoplankton seasonal cycle, of its nutriments and of the dissolved oxygen. (O.M.). 375 refs.

  19. Creep failure of a spray drier

    CSIR Research Space (South Africa)

    Carter, P

    1998-06-01

    Full Text Available , and creep. The calculations pointed to creep, and no positive metallurgic or physical evidence was discovered to support any of the hypotheses. However, the compression stresses implied that creep deformation could have occurred without inducing discernible...

  20. Experimental apparatus for in-pile studies of: creep of nuclear fuels, and Young's-modulus of structural materials; Dispositifs experimentaux pour etudes en pile du fluage des materiaux combustibles, et du module d'elasticite des materiaux de structure

    Energy Technology Data Exchange (ETDEWEB)

    Gautier, A.; Le Bret, P.; Alfille, L.; Pesenti, P. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Creep test under compression: the apparatus described allows to study, in an horizontal beam hole of a research reactor such as EL2, the creep behaviour of nuclear fuel samples under neutron flux. The maximum stress applied on the specimens is a constant compression chooses between 0.200 and 0.400 kg/mm{sup 2} (285 psi and 570 psi). - Young's Modulus measurement: in another horizontal beam hole of such a reactor, an apparatus allows to study the irradiation effect on Young's Modulus of a structural material specimen. (author)Fren. [French] Essai de fluage en compression: l'appareillage decrit permet d'etudier, dans un canal horizontal d'une pile experimentale type EL2, le fluage en compression d'eprouvettes de materiaux fissiles sous le flux de neutrons, sous une contrainte maximum de 500 g/mm{sup 2}. - Mesure du module d'Young: dans un canal identique au precedent, un appareillage permet de suivre l'influence du rayonnement sur le module d'elasticite d'une eprouvette d'un materiau de structure. (auteur)

  1. Tensile cracks in creeping solids

    International Nuclear Information System (INIS)

    Riedel, H.; Rice, J.R.

    1979-02-01

    The loading parameter determining the stress and strain fields near a crack tip, and thereby the growth of the crack, under creep conditions is discussed. Relevant loading parameters considered are the stress intensity factor K/sub I/, the path-independent integral C*, and the net section stress sigma/sub net/. The material behavior is modelled as elastic-nonlinear viscous where the nonlinear term describes power law creep. At the time t = 0 load is applied to the cracked specimen, and in the first instant the stress distribution is elastic. Subsequently, creep deformation relaxes the initial stress concentration at the crack tip, and creep strains develop rapidly near the crack tip. These processes may be analytically described by self-similar solutions for short times t. Small scale yielding may be defined. In creep problems, this means that elastic strains dominate almost everywhere except in a small creep zone which grows around the crack tip. If crack growth ensues while the creep zone is still small compared with the crack length and the specimen size, the stress intensity factor governs crack growth behavior. If the calculated creep zone becomes larger than the specimen size, the stresses become finally time-independent and the elastic strain rates can be neglected. In this case, the stress field is the same as in the fully-plastic limit of power law hardening plasticity. The loading parameter which determines the near tip fields uniquely is then the path-independent integral C*.K/sub I/ and C* characterize opposite limiting cases. The case applied in a given situation is decided by comparing the creep zone size with the specimen size and the crack length. Besides several methods of estimating the creep zone size, a convenient expression for a characteristic time is derived, which characterizes the transition from small scale yielding to extensive creep of the whole specimen

  2. Vortex pinning and creep experiments

    International Nuclear Information System (INIS)

    Kes, P.H.

    1991-01-01

    A brief review of basic flux-pinning and flux-creep ingredients and a selection of experimental results on high-temperature-superconductivity compounds is presented. Emphasis is put on recent results and on those properties which are central to the emerging understanding of the flux-pinning and flux-creep mechanisms of these fascinating materials

  3. Nanogranular origin of concrete creep.

    Science.gov (United States)

    Vandamme, Matthieu; Ulm, Franz-Josef

    2009-06-30

    Concrete, the solid that forms at room temperature from mixing Portland cement with water, sand, and aggregates, suffers from time-dependent deformation under load. This creep occurs at a rate that deteriorates the durability and truncates the lifespan of concrete structures. However, despite decades of research, the origin of concrete creep remains unknown. Here, we measure the in situ creep behavior of calcium-silicate-hydrates (C-S-H), the nano-meter sized particles that form the fundamental building block of Portland cement concrete. We show that C-S-H exhibits a logarithmic creep that depends only on the packing of 3 structurally distinct but compositionally similar C-S-H forms: low density, high density, ultra-high density. We demonstrate that the creep rate ( approximately 1/t) is likely due to the rearrangement of nanoscale particles around limit packing densities following the free-volume dynamics theory of granular physics. These findings could lead to a new basis for nanoengineering concrete materials and structures with minimal creep rates monitored by packing density distributions of nanoscale particles, and predicted by nanoscale creep measurements in some minute time, which are as exact as macroscopic creep tests carried out over years.

  4. Creep buckling analysis of shells

    International Nuclear Information System (INIS)

    Stone, C.M.; Nickell, R.E.

    1977-01-01

    The current study was conducted in an effort to determine the degree of conservatism or lack of conservatism in current ASME design rules concerning time-dependent (creep) buckling. In the course of this investigation, certain observations were made concerning the numerical solution of creep buckling problems. It was demonstrated that a nonlinear finite element code could be used to solve the time-dependent buckling problem. A direct method of solution was presented which proved to be computationally efficient and provided answers which agreed very well with available analytical solutions. It was observed that the calculated buckling times could vary widely for small errors in computed displacements. The presence of high creep strain rates contributed to the prediction of early buckling times when calculated during the primary creep stage. The predicted time estimates were found to increase with time until the secondary stage was reached and the estimates approached the critical times predicted without primary creep. It can be concluded, therefore, that for most nuclear piping components, whose primary creep stage is small compared to the secondary stage, the effect of primary creep is negligible and can be omitted from the calculations. In an evaluation of the past and current ASME design rules for time-dependent, load controlled buckling, it was concluded that current use of design load safety factors is not equivalent to a safety factor of ten on service life for low creep exponents

  5. Thermal ratcheting and creep damage

    International Nuclear Information System (INIS)

    Clement, G.; Cousseran, P.; Roche, R.L.

    1983-08-01

    Creep is a cause of deformation; it may also result in rupture in time. Although LMFBR structures are not heavily loaded, they are subjected to large thermal transients. Can structure lifetime be shortened by such transients. Several proposals have been made to assist adesigners with thermal ratcheting in the creep range. Unfortunately these methods are not validated by experiments, and they take only inelastic distorsion into consideration as creep effects. The aim of the work presented here is to correct these deficiencies in providing an experimental basis to ratcheting analysis rules in the creep range, and in considering the effect of cyclic straining (like cyclic thermal stresses) on the time to rupture by creep. Experimental tests have been performed on austenitic stainless steel at 650 0 C for the first item. Results of these tests and results available in the open literature have been used to built a practical rule of ratcheting analysis. This rule giving a conservative value of the creep distortion, is based on the concept of effective primary stress which is an amplification of the primary stress really applied. Concerning the second point (time to rupture), it was necessary to obtain real creep rupture and not instability. According to the proposal of Pr LECKIE, tests were performed on specimen made out of copper, and of aluminium alloys at temperatures between 150 0 C and 300 0 C. With such materials creep rupture is obtained without necking. Experimental tests show that cyclic straining reduces the time to creep rupture under load controlled stress. Caution must be given to the designer: cyclic thermal stress can lead to premature creep rupture

  6. Electronic structure of the actinides and their dioxides. Application to the defect formation energy and krypton solubility in uranium dioxide; Etude de la structure electronique des actinides et de leurs dioxydes. Application aux defauts ponctuels et aux gaz de fission dans le dioxyde d`uranium

    Energy Technology Data Exchange (ETDEWEB)

    Petit, T. [CEA Centre d`Etudes Nucleaires de Grenoble, 38 (France)]|[CEA Centre d`Etudes de Grenoble, 38 (France). Dept. de Thermohydraulique et de Physique

    1996-09-28

    Uranium dioxide is the standard nuclear fuel used in French h power plants. During irradiation, fission products such as krypton and xenon are created inside fuel pellets. So, gas release could become, at very high burnup, a limiting factor in the reactor exploitation. To study this subject, we have realised calculations using the Density Functional Theory (DFT) into the Local Density Approximation (LDA) and the Atomic Sphere Approximation (ASA). First, we have validated our approach by calculating cohesive properties of thorium, protactinium and uranium metals. The good agreement between our results and experimental values implies that 5f electrons are itinerant. Calculated lattice parameter, cohesive energy and bulk modulus for uranium and thorium dioxides are in very good agreement with experiment. We show that binding between uranium and oxygen atoms is not completely ionic but partially covalent. The question of the electrical conductivity still remains an open problem. We have been able to calculate punctual defect formation energies in uranium dioxide. Accordingly to experimental observations, we find that it is easier to create a defect in the oxygen sublattice than in the uranium sublattice. Finally, we have been able to predict a probable site of krypton atoms in nuclear fuel: the Schottky trio. Experiences of Extended X-ray Absorption Fine structure Spectroscopy (EXAFS) and X-ray Photoelectron Spectroscopy (XPS) on uranium dioxide doped by ionic implantation will help us in the comprehension of the studied phenomena and the interpretation of our calculations. (author). 256 refs.

  7. Mechanisms of transient radiation-induced creep

    International Nuclear Information System (INIS)

    Pyatiletov, Yu.S.

    1981-01-01

    Radiation-induced creep at the transient stage is investigated for metals. The situation, when several possible creep mechanisms operate simultaneously is studied. Among them revealed are those which give the main contribution and determine thereby the creep behaviour. The time dependence of creep rate and its relation to the smelling rate is obtained. The results satisfactorily agree with the available experimental data [ru

  8. Negative creep in nickel base superalloys

    DEFF Research Database (Denmark)

    Dahl, Kristian Vinter; Hald, John

    2004-01-01

    Negative creep describes the time dependent contraction of a material as opposed to the elongation seen for a material experiencing normal creep behavior. Negative creep occurs because of solid state transformations that results in lattice contractions. For most applications negative creep will h...

  9. Multiaxial creep-fatigue rules

    International Nuclear Information System (INIS)

    Spindler, M.W.; Hales, R.; Ainsworth, R.A.

    1997-01-01

    Within the UK, a comprehensive procedure, called R5, is used to assess the high temperature response of structures. One part of R5 deals with creep-fatigue initiation, and in this paper we describe developments in this part of R5 to cover multiaxial stress states. To assess creep-fatigue, damage is written as the linear sum of fatigue and creep components. Fatigue is assessed using Miner's law with the total endurance split into initiation and growth cycles. Initiation is assessed by entering the curve of initiation cycles vs strain range using a Tresca equivalent strain range. Growth is assessed by entering the curve of growth cycles vs strain range using a Rankine equivalent strain range. The number of allowable cycles is obtained by summing the initiation and growth cycles. In this way the problem of defining an equivalent strain range applicable over a range of endurance is avoided. Creep damage is calculated using ductility exhaustion methods. In this paper we address two aspects; first, the nature of stress relaxation and, hence, accumulated creep strain in multiaxial stress fields; secondly, the effect of multiaxial stress on creep ductility. The effect of multiaxial stress state on creep ductility has been examined using experimental data and mechanistic models. Good agreement is demonstrated between an empirical description of test data and a cavity growth model, provided a simple nucleation criterion is included. A simple scaling factor is applied to uniaxial creep ductility, defined as a function of stress state. The factor is independent of the cavity growth mechanisms and yields a value of equivalent strain which can be conveniently used in determining creep damage by ductility exhaustion. (author). 14 refs, 4 figs

  10. Creep in electronic ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Routbort, J. L.; Goretta, K. C.; Arellano-Lopez, A. R.

    2000-04-27

    High-temperature creep measurements combined with microstructural investigations can be used to elucidate deformation mechanisms that can be related to the diffusion kinetics and defect chemistry of the minority species. This paper will review the theoretical basis for this correlation and illustrate it with examples from some important electronic ceramics having a perovskite structure. Recent results on BaTiO{sub 3}, (La{sub 1{minus}x}Sr){sub 1{minus}y}MnO{sub 3+{delta}}, YBa{sub 2}Cu{sub 3}O{sub x}, Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub x}, (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} and Sr(Fe,Co){sub 1.5}O{sub x} will be presented.

  11. Numerical description of creep of highly creep resistant alloys

    International Nuclear Information System (INIS)

    Preussler, T.

    1991-01-01

    Fatigue tests have been performed with a series of highly creep resistant materials for gas turbines and related applications for gaining better creep data up to long-term behaviour. The investigations were performed with selected individual materials in the area of the main applications down to strains and stresses relevant to design, and have attained trial durations of 25000 to 60000 h. In continuing former research, creep equations for a selection of characterizing individual materials have been improved and partly newly developed on the basis of a differentiated evaluation. Concerning the single materials, there are: one melt each of the materials IN-738 LC, IN-939, IN-100, FSX-414 and Inconel 617. The applied differentiated evaluation is based on the elastoplastical behaviour from the hot-drawing test, the creep behaviour from the non interrupted or the interrupted fatigue test, and the contraction behaviour from the annealing test. The creep equations developed describe the high temperature deformation behaviour taking into account primary, secondary and partly the tertiary creep dependent of temperature, stress and time. These equations are valid for the whole application area of the respective material. (orig./MM) [de

  12. Plasticity and creep of metals

    CERN Document Server

    Rusinko, Andrew

    2011-01-01

    Here is a systematic presentation of the postulates, theorems and principles of mathematical theories of plasticity and creep in metals, and their applications. Special attention is paid to analysis of the advantages and shortcomings of the classical theories.

  13. Creep in an electrodeposited nickel

    Czech Academy of Sciences Publication Activity Database

    Sklenička, Václav; Kuchařová, Květa; Kvapilová, Marie; Svoboda, Milan; Král, Petr; Vidrich, G.

    2013-01-01

    Roč. 48, č. 13 (2013), s. 4780-4788 ISSN 0022-2461 R&D Projects: GA ČR(CZ) GAP108/11/2260; GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : nanocrystalline nickel * electrodeposited metals * nanocomposite * creep behavior * creep mechanisms Subject RIV: JG - Metallurgy Impact factor: 2.305, year: 2013

  14. (Irradiation creep of graphite)

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, C.R.

    1990-12-21

    The traveler attended the Conference, International Symposium on Carbon, to present an invited paper, Irradiation Creep of Graphite,'' and chair one of the technical sessions. There were many papers of particular interest to ORNL and HTGR technology presented by the Japanese since they do not have a particular technology embargo and are quite open in describing their work and results. In particular, a paper describing the failure of Minor's law to predict the fatigue life of graphite was presented. Although the conference had an international flavor, it was dominated by the Japanese. This was primarily a result of geography; however, the work presented by the Japanese illustrated an internal program that is very comprehensive. This conference, a result of this program, was better than all other carbon conferences attended by the traveler. This conference emphasizes the need for US participation in international conferences in order to stay abreast of the rapidly expanding HTGR and graphite technology throughout the world. The United States is no longer a leader in some emerging technologies. The traveler was surprised by the Japanese position in their HTGR development. Their reactor is licensed and the major problem in their graphite program is how to eliminate it with the least perturbation now that most of the work has been done.

  15. Datalogger for the creep laboratory

    International Nuclear Information System (INIS)

    Sambasivan, S.I.; Karthikeyan, T.V.; Chowdhary, D.M.; Anantharaman, P.N.

    1989-01-01

    The creep laboratory, MDL/ICGAR is a facility to study the creep properties of materials which are of interest to the fast reactor programme. The creep test is conducted over a few days to several months and years depending on the test variables employed. In these tests the creep strain and creep rate as a function of time are studied while the load and temperature are kept constant. The datalogger automates the process of recording the strain information as a function of time and also monitors the temperature throughout the test. The system handles 126 temperature channels and 42 strain channels from 27 machines. The temperature inputs are from the thermocouples and for cold junction compensation RTD's are used. An extensometer with a linear variable differential transformer (LVDT) or Super Linear Variable Capacitor (SLVC) form the set up to measure strain. The data logger consists of a front end analog input sub-system (AISS), a 8085 based Data Acquisition System (DAS) communicating to a microcomputer with CP/M operating system. The system responds to the user through the console and outputs of a dot matrix printer. The system, running a real time executive, also allows for on line enabling or disabling of a channel, printing of data, examining the current status and value, setting and getting time etc. (author)

  16. Creep of plasma sprayed zirconia

    Science.gov (United States)

    Firestone, R. F.; Logan, W. R.; Adams, J. W.

    1982-01-01

    Specimens of plasma-sprayed zirconia thermal barrier coatings with three different porosities and different initial particle sizes were deformed in compression at initial loads of 1000, 2000, and 3500 psi and temperatures of 1100 C, 1250 C, and 1400 C. The coatings were stabilized with lime, magnesia, and two different concentrations of yttria. Creep began as soon as the load was applied and continued at a constantly decreasing rate until the load was removed. Temperature and stabilization had a pronounced effect on creep rate. The creep rate for 20% Y2O3-80% ZrO2 was 1/3 to 1/2 that of 8% Y2O3-92% ZrO2. Both magnesia and calcia stabilized ZrO2 crept at a rate 5 to 10 times that of the 20% Y2O3 material. A near proportionality between creep rate and applied stress was observed. The rate controlling process appeared to be thermally activated, with an activation energy of approximately 100 cal/gm mole K. Creep deformation was due to cracking and particle sliding.

  17. Bisphosphine dioxides

    Energy Technology Data Exchange (ETDEWEB)

    Moloy, Kenneth G. (Charleston, WV)

    1990-01-01

    A process for the production of organic bisphosphine dioxides from organic bisphosphonates. The organic bisphosphonate is reacted with a Grignard reagent to give relatively high yields of the organic bisphosphine dioxide.

  18. Bisphosphine dioxides

    Energy Technology Data Exchange (ETDEWEB)

    Moloy, K.G.

    1990-02-20

    A process is described for the production of organic bisphosphine dioxides from organic bisphosphonates. The organic bisphosphonate is reacted with a Grignard reagent to give relatively high yields of the organic bisphosphine dioxide.

  19. Creep of service-aged welds

    OpenAIRE

    Sun, Wei

    1996-01-01

    The creep behaviour of welds in service-aged pipes are studied. The aims of the research have been achieved using analytical, numerical and experimental approaches to the relevant subjects. Several features of the work are presented: (i) a systematic parametric study of the creep of two-material test specimens including a stress singularity analysis, (ii) an impression creep testing method using a rectangular indenter, which can be applied to study the creep properties in welds, and (iii) met...

  20. Influence of variations in creep curve on creep behavior of a high-temperature structure

    International Nuclear Information System (INIS)

    Hada, Kazuhiko

    1986-01-01

    It is one of the key issues for a high-temperature structural design guideline to evaluate the influence of variations in creep curve on the creep behavior of a high-temperature structure. In the present paper, a comparative evaluation was made to clarify such influence. Additional consideration was given to the influence of the relationship between creep rupture life and minimum creep rate, i.e., the Monkman-Grant's relationship, on the creep damage evaluation. The consideration suggested that the Monkman-Grant's relationship be taken into account in evaluating the creep damage behavior, especially the creep damage variations. However, it was clarified that the application of the creep damage evaluation rule of ASME B and P.V. Code Case N-47 to the ''standard case'' which was predicted from the average creep property would predict the creep damage on the safe side. (orig./GL)

  1. Creep and Creep-Fatigue of Alloy 617 Weldments

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Jill K. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Carroll, Laura J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wright, Richard N. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-08-01

    Alloy 617 is the primary candidate material for the heat exchanger of a very high temperature gas cooled reactor intended to operate up to 950°C. While this alloy is currently qualified in the ASME Boiler and Pressure Vessel Code for non-nuclear construction, it is not currently allowed for use in nuclear designs. A draft Code Case to qualify Alloy 617 for nuclear pressure boundary applications was submitted in 1992, but was withdrawn prior to approval. Prior to withdrawal of the draft, comments were received indicating that there was insufficient knowledge of the creep and creep-fatigue behavior of Alloy 617 welds. In this report the results of recent experiments and analysis of the creep-rupture behavior of Alloy 617 welds prepared using the gas tungsten arc process with Alloy 617 filler wire. Low cycle fatigue and creep-fatigue properties of weldments are also discussed. The experiments cover a range of temperatures from 750 to 1000°C to support development of a new Code Case to qualify the material for elevated temperature nuclear design. Properties of the welded material are compared to results of extensive characterization of solution annealed plate base metal.

  2. COMPARISON OF CLADDING CREEP RUPTURE MODELS

    Energy Technology Data Exchange (ETDEWEB)

    P. Macheret

    2000-06-12

    The objective of this calculation is to compare several creep rupture correlations for use in calculating creep strain accrued by the Zircaloy cladding of spent nuclear fuel when it has been emplaced in the repository. These correlations are used to calculate creep strain values that are then compared to a large set of experimentally measured creep strain data, taken from four different research articles, making it possible to determine the best fitting correlation. The scope of the calculation extends to six different creep rupture correlations.

  3. Creep Resistance of VM12 Steel

    Directory of Open Access Journals (Sweden)

    Zieliński A.

    2016-09-01

    Full Text Available This article presents selected material characteristics of VM12 steel used for elements of boilers with super- and ultra-critical steam parameters. In particular, abridged and long-term creep tests with and without elongation measurement during testing and investigations of microstructural changes due to long-term impact of temperature and stress were carried out. The practical aspect of the use of creep test results in forecasting the durability of materials operating under creep conditions was presented. The characteristics of steels with regard to creep tests developed in this paper are used in assessment of changes in functional properties of the material of elements operating under creep conditions.

  4. Negative creep in nickel base superalloys

    DEFF Research Database (Denmark)

    Dahl, Kristian Vinter; Hald, John

    2004-01-01

    Negative creep describes the time dependent contraction of a material as opposed to the elongation seen for a material experiencing normal creep behavior. Negative creep occurs because of solid state transformations that results in lattice contractions. For most applications negative creep...... will have no practical implications but under certain conditions it may become critical. For bolts and fasteners, which are highly constrained during service, negative creep may lead to dramatically increased stresses and eventually to failure. The article was inspired by a recent failure of Nimonic 80A...

  5. Modelling of diffusional creep in polycrystals

    Energy Technology Data Exchange (ETDEWEB)

    Pein, Cornelia; Sommitsch, Christof [Technische Univ. Graz (Austria). Inst. for Materials Science and Welding

    2010-07-01

    To study creep behaviour on a microstructure level is of major importance, because the microstructure of metallic materials and its influence on creep phenomena is complex. Therefore a physically based finite element model is introduced to study the deformation behaviour due to diffusion creep phenomena. The influence of grain boundaries triple junctions and precipitates on creep strains and stresses is simulated. The results indicate that the different microstructure configurations, such as the presence of triple points, second phase particles and the relative orientation of grain boundaries to the loading direction influence the stress distribution and therefore lead to a highly heterogenous creep strain distribution. (orig.)

  6. Creep of ice: further studies

    International Nuclear Information System (INIS)

    Heard, H.C.; Durham, W.B.; Kirby, S.H.

    1987-01-01

    Detailed studies have been done of ice creep as related to the icy satellites, Ganymede and Callisto. Included were: (1) the flow of high-pressure water ices II, III, and V, and (2) frictional sliding of ice I sub h. Work was also begun on the study of the effects of impurities on the flow of ice. Test results are summarized

  7. Low stress creep of stainless steel

    International Nuclear Information System (INIS)

    Crossland, I.G.; Clay, B.D.; Baker, C.

    1976-06-01

    The creep of 20%Cr, 25%Ni, Nb stainless steel has been examined at temperatures from 675 to 775 0 C at sheer stressed below 13 MPa and grain sizes from 6 to 20μm. The results have indicated that the initial creep rates were linearly dependent upon stress but with a threshold stress below which no creep occurred, i.e. Bingham behaviour; in addition, the creep activation energy at small strains was substantially lower than the lattice self-diffusion value and the initial creep rates were approximately related to the grain size through an inverse cube relation. It has been concluded that at low strains (approaching the initial elastic deflection) the creep mechanism was probably that of grain boundary diffusion creep (Coble, 1963) and this is further supported by the close agreement between the observed and theoretically predicted creep rate values. Steady-state creep rates were not observed; initially the creep rates fell rapidly with strain after which a more gradual decrease occurred. Whilst the creep rate - stress relationship continued to be of a Bingham form, the progressive reduction in creep rate with strain was found to be mainly attributable to an increase in the effective viscosity, threshold stress effects being generally of secondary importance. A model has been proposed which explains the initial creep rates as being due to Cable creep with elastic accommodation at grain boundary particles. At higher strains grain boundary collapse caused by vacancy sinking is accommodated at precipitate particles by plastic deformation of the adjacent matrix material. (author)

  8. ETUDE - European Trade Union Distance Education.

    Science.gov (United States)

    Creanor, Linda; Walker, Steve

    2000-01-01

    Describes transnational distance learning activities among European trade union educators carried out as part of the European Trade Union Distance Education (ETUDE) project, supported by the European Commission. Highlights include the context of international trade union distance education; tutor training course; tutors' experiences; and…

  9. Living with creep damage - outside the creep range

    Energy Technology Data Exchange (ETDEWEB)

    Brear, M.; Jarvis, P. [Stress Engineering Services, Europe, Ltd., Esher (United Kingdom)

    2007-06-15

    This paper addresses the effects of creep cavitation damage on other mechanical properties - chiefly those that affect behaviour outside the creep range. Such effects seem not to have been systematically studied, yet they are significant for the understanding and prediction of component integrity and life. The paper presents results obtained mainly as by-products of research programmes on low-alloy steels for both fossil and nuclear power plant and seeks to rationalise the findings to generate an overall picture of the effect. It is seen that a simple loss-of-effective-section model is adequate to describe many of the phenomena observed, but that other factors may also need consideration. (orig.)

  10. Creep in commercially pure metals

    International Nuclear Information System (INIS)

    Nabarro, F.R.N.

    2006-01-01

    The creep of commercially pure polycrystalline metals under constant stress has four stages: a virtually instantaneous extension, decelerating Andrade β creep, almost steady-state Andrade κ creep, and an acceleration towards failure. Little is known about the first stage, and the fourth stage has been extensively reviewed elsewhere. The limited experimental evidence on the physical mechanism of the second stage is reviewed and a critical discussion is given of various theories of this stage. The dependence of strain rate on stress in the third, steady-state, period seems to fall into two regimes, a power law with an exponent of about 4-5, and a rather closely exponential law. The limits of the parameters within which a simple theory of the exponential dependence can be expected to be valid are discussed, and found to be compatible with experiments. Theories of the power-law dependence are discussed, and, appear to be unconvincing. The theoretical models do not relate closely to the metallographic and other physical observations. In view of the weakness of theory, experiments which may indicate the physical processes dominant in steady-state creep are reviewed. It is usually not clear whether they pertain to the power-law or the exponential regime. While the theories all assume that most of the deformation occurs homogeneously within the grains, most experimental observations point strongly to a large deformation at or close to the grain boundaries. However, a detailed study of dislocation processes in a single grain of polycrystalline foil strained in the electron microscope shows that most of the observed strain can be accounted for by the motion of single dislocations through the subgrain structure. There is no clear reconciliation of these two sets of observations. Grain-boundary sliding cannot occur without intragranular deformation. One or other process may dominate the overall deformation; the geometrically dominant process may not be the rate

  11. A study on creep properties of laminated rubber bearings. Pt. 1. Creep properties and numerical simulations of thick rubber bearings

    International Nuclear Information System (INIS)

    Matsuda, Akihiro; Yabana, Shuichi

    2000-01-01

    In this report, to evaluate creep properties and effects of creep deformation on mechanical properties of thick rubber bearings for three-dimensional isolation system, we show results of compression creep test for rubber bearings of various rubber materials and shapes and development of numerical simulation method. Creep properties of thick rubber bearings were obtained from compression creep tests. The creep strain shows steady creep that have logarithmic relationships between strain and time and accelerated creep that have linear relationships. We make numerical model of a rubber material with nonlinear viscoelastic constitutional equations. Mechanical properties after creep loading test are simulated with enough accuracy. (author)

  12. Creep of parylene-C film

    KAUST Repository

    Lin, Jeffrey Chun-Hui

    2011-06-01

    The glass transition temperature of as-deposited parylene-C is first measured to be 50°C with a ramping-temperature-dependent modulus experiment. The creep behavior of parylene-C film in the primary and secondary creep region is then investigated below and above this glass transition temperature using a dynamic mechanical analysis (DMA) machine Q800 from TA instruments at 8 different temperatures: 10, 25, 40, 60, 80, 100, 120 and 150°C. The Burger\\'s model, which is the combined Maxwell model and Kelvin-Voigt model, fits well with our primary and secondary creep data. Accordingly, the results show that there\\'s little or no creep below the glass transition temperature. Above the glass transition temperature, the primary creep and creep rate increases with the temperature, with a retardation time constant around 6 minutes. © 2011 IEEE.

  13. Control of epoxy creep using graphene.

    Science.gov (United States)

    Zandiatashbar, Ardavan; Picu, Catalin R; Koratkar, Nikhil

    2012-06-11

    The creep behavior of epoxy-graphene platelet (GPL) nanocomposites with different weight fractions of filler is investigated by macroscopic testing and nanoindentation. No difference is observed at low stress and ambient temperature between neat epoxy and nanocomposites. At elevated stress and temperature the nanocomposite with the optimal weight fraction, 0.1 wt% GPLs, creeps significantly less than the unfilled polymer. This indicates that thermally activated processes controlling the creep rate are in part inhibited by the presence of GPLs. The phenomenon is qualitatively similar at the macroscale and in nanoindentation tests. The results are compared with the creep of epoxy-single-walled (SWNT) and multi-walled carbon nanotube (MWNT) composites and it is observed that creep in both these systems is similar to that in pure epoxy, that is, faster than creep in the epoxy-GPL system considered in this work. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Room temperature creep in metals and alloys

    Energy Technology Data Exchange (ETDEWEB)

    Deibler, Lisa Anne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Materials Characterization and Performance

    2014-09-01

    Time dependent deformation in the form of creep and stress relaxation is not often considered a factor when designing structural alloy parts for use at room temperature. However, creep and stress relaxation do occur at room temperature (0.09-0.21 Tm for alloys in this report) in structural alloys. This report will summarize the available literature on room temperature creep, present creep data collected on various structural alloys, and finally compare the acquired data to equations used in the literature to model creep behavior. Based on evidence from the literature and fitting of various equations, the mechanism which causes room temperature creep is found to include dislocation generation as well as exhaustion.

  15. Transitional Thermal Creep of Early Age Concrete

    DEFF Research Database (Denmark)

    Hauggaard-Nielsen, Anders Boe; Damkilde, Lars; Freiesleben Hansen, Per

    1999-01-01

    Couplings between creep of hardened concrete and temperature/water effects are well-known. Both the level and the gradients in time of temperature or water content influence the creep properties. In early age concrete the internal drying and the heat development due to hydration increase the effe...... of experimental results for creep of early age and hardened concrete either at different constant temperature levels or for varuing temperature histories illustrate the model....

  16. Tensile creep of beta phase zircaloy-2

    International Nuclear Information System (INIS)

    Burton, B.; Reynolds, G.L.; Barnes, J.P.

    1977-08-01

    The tensile creep and creep rupture properties of beta-phase zircaloy-2 are studied under vacuum in the temperature and stress range 1300-1550 K and 0.5-2 MN/m 2 . The new results are compared with previously reported uniaxial and biaxial data. A small but systematic difference is noted between the uniaxial and biaxial creep data and reasons for this discrepancy are discussed. (author)

  17. Modeling of creep for structural analysis

    Energy Technology Data Exchange (ETDEWEB)

    Naumenko, K.; Altenbach, H. [Halle-Wittenberg Univ., Halle (Germany). Lehrstuhl fuer Technische Mechanik

    2007-07-01

    ''Creep Modeling for Structural Analysis'' develops methods to simulate and analyze the time-dependent changes of stress and strain states in engineering structures up to the critical stage of creep rupture. The principal subjects of creep mechanics are the formulation of constitutive equations for creep in structural materials under multi-axial stress states; the application of structural mechanics models of beams, plates, shells and three-dimensional solids and the utilization of procedures for the solution of non-linear initial-boundary value problems. The objective of this book is to review some of the classical and recently proposed approaches to the modeling of creep for structural analysis applications as well as to extend the collection of available solutions of creep problems by new, more sophisticated examples. In Chapter 1, the book discusses basic features of the creep behavior in materials and structures and presents an overview of various approaches to the modeling of creep. Chapter 2 collects constitutive models that describe creep and damage processes under multi-axial stress states. Chapter 3 deals with the application of constitutive models to the description of creep for several structural materials. Constitutive and evolution equations, response functions and material constants are presented according to recently published experimental data. In Chapter 4 the authors discuss structural mechanics problems. Governing equations of creep in three-dimensional solids, direct variational methods and time step algorithms are reviewed. Examples are presented to illustrate the application of advanced numerical methods to the structural analysis. An emphasis is placed on the development and verification of creep-damage material subroutines inside the general purpose finite element codes. (orig.)

  18. Viscoelastic creep of high-temperature concrete

    International Nuclear Information System (INIS)

    Pfeiffer, P.A.; Marchertas, A.H.; Bazant, Z.P.

    1985-01-01

    Presented in this report is the analytical model for analysis of high temperature creep response of concrete. The creep law used is linear (viscoelastic), the temperature and moisture effects on the creep rate and also aging are included. Both constant and transient temperature as well as constant and transient moisture conditions are considered. Examples are presented to correlate experimental data with parameters of the analytical model by the use of a finite element scheme

  19. Model for transient creep of southeastern New Mexico rock salt

    International Nuclear Information System (INIS)

    Herrmann, W.; Wawersik, W.R.; Lauson, H.S.

    1980-11-01

    In a previous analysis, existing experimental data pertaining to creep tests on rock salt from the Salado formation of S.E. New Mexico were fitted to an exponential transient creep law. While very early time portions of creep strain histories were not fitted very well for tests at low temperatures and stresses, initial creep rates in particular generally being underestimated, the exponential creep law has the property that the transient creep strain approaches a finite limit with time, and is therefore desirable from a creep modelling point of view. In this report, an analysis of transient creep is made. It is found that exponential transient creep can be related to steady-state creep through a universal creep curve. The resultant description is convenient for creep analyses where very early time behavior is not important

  20. Study on the creep constitutive equation of Hastelloy X, (1)

    International Nuclear Information System (INIS)

    Hada, Kazuhiko; Mutoh, Yasushi

    1983-01-01

    A creep constitutive equation of Hastelloy X was obtained from available experimental data. A sensitivity analysis of this creep constitutive equation was carried out. As the result, the following were revealed: (i) Variations in creep behavior with creep constitutive equation are not small. (ii) In a simpler stress change pattern, variations in creep behavior are similar to those in the corresponding fundamental creep characteristics (creep strain curve, stress relaxation curve, etc.). (iii) Cumulative creep damage estimated in accordance with ASME Boiler and Pressure Vessel Code Case N-47 from a stress history predicted by ''the standard creep constitutive equation'' which predicts the average behavior of creep strain curve data is not thought to be on the safe side on account of uncertainties in creep damage caused by variations in creep strain curve. (author)

  1. Creep of Li2O

    International Nuclear Information System (INIS)

    Hollenberg, G.W.; Arthur, B.; Lui, Y.Y.

    1985-01-01

    The objective of this effort was to obtain data on the performance of lithium ceramic materials during fast neutron irradiation in support of solid breeder blanket designs. Li 2 O has been observed to swell (greater than or equal to 4%) under fast reactor irradiation. Fortunately, Li 2 O deforms at low temperatures so that swelling strains may be internally accommodated. Laboratory creep experiments were conducted between 500 to 700 0 C in order to provide data for structural analysis of in-reactor experiments and blanket design studies. A densification model agreed with most of the available data

  2. Creep of Li2O

    International Nuclear Information System (INIS)

    Hollenberg, G.W.; Liu, Y.Y.; Arthur, B.

    1984-11-01

    The tritium breeding material with the highest lithium atom density, Li 2 O has been observed to incur significant swelling (>4%) under fast reactor irradiation. Such swelling, if unrestrained leads to either unacceptable, induced-strains in adjacent structural material or undesirable design compromises. Fortunately, however, Li 2 O deforms at low temperatures so that swelling strains may be internally accommodated. Laboratory dilational creep experiments were conducted on unirradiated Li 2 O between 500 and 700 0 C in order to provide data for structural analysis of in-reactor experiments and blanket design studies. A densification model agreed with most of the available data

  3. Creating Pedagogical Etudes for Interactive Instruments

    OpenAIRE

    Butler, Jennifer

    2008-01-01

    In this paper I discuss the importance of and need forpedagogical materials to support the development of newinterfaces and new instruments for electronic music. I describemy method for creating a graduated series of pedagogicaletudes composed using Max/MSP. The etudes will helpperformers and instrument designers learn the most commonlyused basic skills necessary to perform with interactiveelectronic music instruments. My intention is that the finalseries will guide a beginner from these init...

  4. Thermal Creep Force: Analysis And Application

    Science.gov (United States)

    2016-06-01

    The boundary condition was inflow and outflow so particles whose trajectory took them outside the simulation space would no longer be simulated and...Calhoun: The NPS Institutional Archive Theses and Dissertations Thesis and Dissertation Collection 2016-06 Thermal creep force: analysis and...CALIFORNIA DISSERTATION Approved for public release; distribution is unlimited THERMAL CREEP FORCE: ANALYSIS AND APPLICATION by David

  5. Making Ice Creep in the Classroom

    Science.gov (United States)

    Prior, David; Vaughan, Matthew; Banjan, Mathilde; Hamish Bowman, M.; Craw, Lisa; Tooley, Lauren; Wongpan, Pat

    2017-04-01

    Understanding the creep of ice has direct application to the role of ice sheet flow in sea level and climate change and to modelling of icy planets and satellites of the outer solar system. Additionally ice creep can be used as an analogue for the high temperature creep of rocks, most particularly quartzites. We adapted technologies developed for ice creep experiments in the research lab, to build some inexpensive ( EU200) rigs to conduct ice creep experiments in an undergraduate (200 and 300 level) class in rock deformation. The objective was to give the students an experience of laboratory rock deformation experiments so that they would understand better what controls the creep rate of ice and rocks. Students worked in eight groups of 5/6 students. Each group had one deformation rig and temperature control system. Each group conducted two experiments over a 2 week period. The results of all 16 experiments were then shared so that all students could analyse the mechanical data and generate a "flow law" for ice. Additionally thin sections were made of each deformed sample so that some microstructural analysis could be incorporated in the data analysis. Students were able to derive a flow law that showed the relationship of creep rate to both stress and temperature. The flow law matches with those from published research. The class did provide a realistic introduction to laboratory rock deformation experiments and helped students' understanding of what controls the creep of rocks.

  6. Significance of primary irradiation creep in graphite

    CSIR Research Space (South Africa)

    Erasmus, C

    2013-05-01

    Full Text Available Traditionally primary irradiation creep is introduced into graphite analysis by applying the appropriate amount of creep strain to the model at the initial time-step. This is valid for graphite components that are subjected to high fast neutron flux...

  7. Creep resistant high temperature martensitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Hawk, Jeffrey A.; Jablonski, Paul D.; Cowen, Christopher J.

    2015-11-13

    The disclosure provides a creep resistant alloy having an overall composition comprised of iron, chromium, molybdenum, carbon, manganese, silicon, nickel, vanadium, niobium, nitrogen, tungsten, cobalt, tantalum, boron, and potentially additional elements. In an embodiment, the creep resistant alloy has a molybdenum equivalent Mo(eq) from 1.475 to 1.700 wt. % and a quantity (C+N) from 0.145 to 0.205. The overall composition ameliorates sources of microstructural instability such as coarsening of M.sub.23C.sub.6 carbides and MX precipitates, and mitigates or eliminates Laves and Z-phase formation. A creep resistant martensitic steel may be fabricated by preparing a melt comprised of the overall composition followed by at least austenizing and tempering. The creep resistant alloy exhibits improved high-temperature creep strength in the temperature environment of around 650.degree. C.

  8. Creep resistant high temperature martensitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Hawk, Jeffrey A.; Jablonski, Paul D.; Cowen, Christopher J.

    2017-01-31

    The disclosure provides a creep resistant alloy having an overall composition comprised of iron, chromium, molybdenum, carbon, manganese, silicon, nickel, vanadium, niobium, nitrogen, tungsten, cobalt, tantalum, boron, copper, and potentially additional elements. In an embodiment, the creep resistant alloy has a molybdenum equivalent Mo(eq) from 1.475 to 1.700 wt. % and a quantity (C+N) from 0.145 to 0.205. The overall composition ameliorates sources of microstructural instability such as coarsening of M.sub.23C.sub.6carbides and MX precipitates, and mitigates or eliminates Laves and Z-phase formation. A creep resistant martensitic steel may be fabricated by preparing a melt comprised of the overall composition followed by at least austenizing and tempering. The creep resistant alloy exhibits improved high-temperature creep strength in the temperature environment of around 650.degree. C.

  9. Statistical analysis of concrete creep effects

    International Nuclear Information System (INIS)

    Floris, C.

    1989-01-01

    The principal sources of uncertainty in concrete creep effects are the following: uncertainty in the stochastic evolution in time of the mechanism of creep (internal uncertainty); uncertainty in the prediction of the properties of the materials; uncertainty in the stochastic evolution of environmental conditions; uncertainty of the theoretical models; errors of measurement. Interest in the random nature of concrete creep (and shrinkage) effects is discussed. The late beginning of the studies on this subject is perhaps due to their theoretical and computational complexity: nevertheless, since creep and shrinkage affect features of concrete structures as the residual prestressing force in prestressed sections, the stress redistribution in steel-concrete composite beams, deflections and deformations, stress distributions in non-homogenous structures, reactions due to delayed restraints and creep buckling, these studies are very important. This paper is aimed to find the statistics of some of these effects taking into the account the third type of source of uncertainty

  10. Assessment of concrete creep and shrinkage

    International Nuclear Information System (INIS)

    Trivedi, Neha; Singh, R.K.

    2012-01-01

    B-3 model prediction of concrete creep and shrinkage strains on cylindrical specimen and BARC Containment test model (BARCOM) are presented. Experimental shrinkage strain is shown to be in agreement with B-3 model predictions for cylindrical specimen and BARCOM. Creep strain in cylindrical specimen is found to be in agreement with B-3 model. In BARCOM for wall cast in different pores, creep strain is in agreement with B-3 model in hoop direction however in longitudinal direction, observed creep strain in higher than B-3 model. For dome structure cast in a single pour, experimental creep strain shows confirmity with B-3 model both in hoop and longitudinal directions. The study on concrete aging and average longitudinal shrinkage strain is carried out. (author)

  11. Creep and relaxation behavior of Inconel-617

    International Nuclear Information System (INIS)

    Osthoff, W.; Ennis, P.J.; Nickel, H.; Schuster, H.

    1984-01-01

    The static and dynamic creep behavior of Inconel alloy 617 has been determined in constant load creep tests, relaxation tests, and stress reduction tests in the temperature range 1023 to 1273 K. The results have been interpreted using the internal stress concept: The dependence of the internal stress on the applied stress and test temperature was determined. In a few experiments, the influence of cold deformation prior to the creep test on the magnitude of the internal stress was also investigated. It was found that the experimentally observed relaxation behavior could be more satisfactorily described using the Norton creep equation modified by incorporation of the internal stress than by the conventional Norton creep equation

  12. Deformation mechanisms in cyclic creep and fatigue

    International Nuclear Information System (INIS)

    Laird, C.

    1979-01-01

    Service conditions in which static and cyclic loading occur in conjunction are numerous. It is argued that an understanding of cyclic creep and cyclic deformation are necessary both for design and for understanding creep-fatigue fracture. Accordingly a brief, and selective, review of cyclic creep and cyclic deformation at both low and high strain amplitudes is provided. Cyclic loading in conjunction with static loading can lead to creep retardation if cyclic hardening occurs, or creep acceleration if softening occurs. Low strain amplitude cyclic deformation is understood in terms of dislocation loop patch and persistent slip band behavior, high strain deformation in terms of dislocation cell-shuttling models. While interesting advances in these fields have been made in the last few years, the deformation mechanisms are generally poorly understood

  13. Creep behavior of Zr-Nb alloys

    Energy Technology Data Exchange (ETDEWEB)

    Suh, Yong Chan; Kim, Young Suk; Cheong, Yong Mu; Kwon, Sang Chul; Kim, Sung Soo; Choo, Ki Nam [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-01-01

    The creep characteristics of Zirconium alloy is affected by several parameters. Out-reactor creep increases both with an increasing amount of Nb, Sn and S contained in alpha-Zr and decreases with the increasing volume of alpha-Zr. Especially, the creep of Zr-2.5Nb alloy depends on the solubility of Nb in alpha-Zr, which is associated with the decomposition of beta-Zr. Since Zr of the hcp structure is strongly anisotropic, it shows the characteristics of texture and results in the anisotropy of creep. Due to the circumferential texture of Zr-2.5%Nb alloy (CANDU Pressure tube), the longitudinal slip is easier than the circumferential one, resulting in the high creep rate. The irradiation creep also increases with increasing neutron fluence. The neutron irradiation increases the strength of the zirconium alloys but decreases their creep strength. In contrast to the out-reactor creep, the irradiation creep is little sensitive to temperature, resulting in the lower activation energy. The most important factor to affect the in-reactor and out-reactor creep of niobium containing alloys seems to be the solution hardening by Nb or Sn which is soluble in alpha-zirconium and the texture as well. Irradiation growth is the mechanism which is caused only by the irradiation. It becomes saturated at lower fluence than the critical fluence but beyond it, shows the break-away growth. The onset of accelerated irradiation growth corresponds with the c-dislocation loop formation, though its mechanism needs better understanding. Generally, the irradiation growth of Zr-Nb alloys increases with an increase in fluence, cold working, dislocation, density and temperature, and with a decrease in the grain size. 141 refs., 59 figs., 10 tabs. (Author)

  14. Advances in the assessment of creep data

    Energy Technology Data Exchange (ETDEWEB)

    Holdsworth, S.R.

    2010-07-01

    Many of the classical models representing the creep and rupture behaviour of metals were developed prior to and during the 1950s and 1960s, and their subsequent exploitation, in particular for the assessment of large creep property datasets, was initially limited by the capability of the analytical tools available at the time. The formation of ECCC (the European Creep Collaborative Committee) in 1991, with a main objective of providing reliable peer reviewed long-time creep property values for European Design and Product Standards, led to the development of rigorous assessment procedures such as PD6605 and DESA incorporating post assessment tests to verify: physical realism, effectiveness of model-fit within the range of the source experimental data, and extrapolation credibility. The first ECCC assessment recommendations published in 1996 undoubtedly provided a catalyst for others to exploit the availability of low cost, powerful desktop computers to develop rigorous methodologies for the physically realistic analysis of uniaxial and multi-axial data for the reliable and accurate characterisation of creep strain, and rupture strength and ductility properties. More recent improvements in data assessment methodologies have been driven by the need to effectively model the creep deformation and rupture characteristics of the complex new generation alloys and fabrications being designed to cater for the continually evolving requirements of modern advanced power plant. These advances in the assessment of creep data are reviewed. (orig.)

  15. Creep behavior evaluation of welded joint

    International Nuclear Information System (INIS)

    Susei, Shuzo; Matsui, Shigetomo; Mori, Eisuke; Shimizu, Shigeki; Satoh, Keisuke.

    1980-01-01

    In the creep design of high temperature structural elements, it is necessary to grasp the creep performance of joints as a whole, paying attention to the essential lack of uniformity between the material qualities of parent metals and welds. In this study, the factors controlling the creep performance of butt welded joints were investigated theoretically, when they were subjected to lateral tension and longitudinal tension. It was clarified that the rupture time in the case of laterally pulled joints was determined by the ratio of the creep rupture times of weld metals and parent metals, and the rupture time in the case of longitudinally pulled joints was determined by the ratio of the creep rupture times and the ratio of the creep strain rates of weld metals and parent metals. Moreover, when the joints of the former ratio less than 1 and the latter ratio larger than 1 were investigated experimentally, the rupture time in the case of laterally pulled joints was affected by the relative thickness, and when the relative thickness was large, the theoretical and the experimental values coincided, but the relative thickness was small, the theoretical values gave the evaluation on safe side as compared with the experimental values due to the effect of restricting deformation. In the case of longitudinally pulled joints, the theoretical and the experimental values coincided relatively well. The diagram of classifying the creep performance of welded joints was proposed. (Kako, I.)

  16. A simple model for indentation creep

    Science.gov (United States)

    Ginder, Ryan S.; Nix, William D.; Pharr, George M.

    2018-03-01

    A simple model for indentation creep is developed that allows one to directly convert creep parameters measured in indentation tests to those observed in uniaxial tests through simple closed-form relationships. The model is based on the expansion of a spherical cavity in a power law creeping material modified to account for indentation loading in a manner similar to that developed by Johnson for elastic-plastic indentation (Johnson, 1970). Although only approximate in nature, the simple mathematical form of the new model makes it useful for general estimation purposes or in the development of other deformation models in which a simple closed-form expression for the indentation creep rate is desirable. Comparison to a more rigorous analysis which uses finite element simulation for numerical evaluation shows that the new model predicts uniaxial creep rates within a factor of 2.5, and usually much better than this, for materials creeping with stress exponents in the range 1 ≤ n ≤ 7. The predictive capabilities of the model are evaluated by comparing it to the more rigorous analysis and several sets of experimental data in which both the indentation and uniaxial creep behavior have been measured independently.

  17. Low-temperature creep of austenitic stainless steels

    Science.gov (United States)

    Reed, R. P.; Walsh, R. P.

    2017-09-01

    Plastic deformation under constant load (creep) in austenitic stainless steels has been measured at temperatures ranging from 4 K to room temperature. Low-temperature creep data taken from past and unreported austenitic stainless steel studies are analyzed and reviewed. Creep at cryogenic temperatures of common austenitic steels, such as AISI 304, 310 316, and nitrogen-strengthened steels, such as 304HN and 3116LN, are included. Analyses suggests that logarithmic creep (creep strain dependent on the log of test time) best describe austenitic stainless steel behavior in the secondary creep stage and that the slope of creep strain versus log time is dependent on the applied stress/yield strength ratio. The role of cold work, strain-induced martensitic transformations, and stacking fault energy on low-temperature creep behavior is discussed. The engineering significance of creep on cryogenic structures is discussed in terms of the total creep strain under constant load over their operational lifetime at allowable stress levels.

  18. Creep substructure formation in sodium chloride single crystals in the power law and exponential creep regimes

    Science.gov (United States)

    Raj, S. V.; Pharr, G. M.

    1989-01-01

    Creep tests conducted on NaCl single crystals in the temperature range from 373 to 1023 K show that true steady state creep is obtained only above 873 K when the ratio of the applied stress to the shear modulus is less than or equal to 0.0001. Under other stress and temperature conditions, corresponding to both power law and exponential creep, the creep rate decreases monotonically with increasing strain. The transition from power law to exponential creep is shown to be associated with increases in the dislocation density, the cell boundary width, and the aspect ratio of the subgrains along the primary slip planes. The relation between dislocation structure and creep behavior is also assessed.

  19. Compressive creep of silicon nitride

    International Nuclear Information System (INIS)

    Silva, C.R.M. da; Melo, F.C.L. de; Cairo, C.A.; Piorino Neto, F.

    1990-01-01

    Silicon nitride samples were formed by pressureless sintering process, using neodymium oxide and a mixture of neodymium oxide and yttrio oxide as sintering aids. The short term compressive creep behaviour was evaluated over a stress range of 50-300 MPa and temperature range 1200 - 1350 0 C. Post-sintering heat treatments in nitrogen with a stepwise decremental variation of temperature were performed in some samples and microstructural analysis by X-ray diffraction and transmission electron microscopy showed that the secondary crystalline phase which form from the remnant glass are dependent upon composition and percentage of aditives. Stress exponent values near to unity were obtained for materials with low glass content suggesting grain boundary diffusion accommodation processes. Cavitation will thereby become prevalent with increase in stress, temperature and decrease in the degree of crystallization of the grain boundary phase. (author) [pt

  20. Modelling of cladding creep collapse

    International Nuclear Information System (INIS)

    Koundy, V.; Forgeron, T.; Hivroz, J.

    1993-01-01

    The effects of the initial ovality and pressure level on the collapse time of Zircaloy-4 tubing subjected to uniform external pressure were examined experimentally and analytically. Experiments were performed on end closed tubes with two metallurgical states: stress relieved and recrystallized. Numerical simulations were accomplished with a specific computer program based on an analytical approach and the calculated results were compared with the experimental ones. As a comparison, the finite element method is also partially examined in this analysis. Numerical collapse times are in good agreement with regard to experimental results in the case of stress relieved structure. They seem to be too conservative in the case of a recrystallized metallurgical state and the use of the anisotropic option ameliorates numerical results. Sensibility of numerical solutions to the formulation of primary creep laws are presented

  1. Demonstration of creep during filtration

    DEFF Research Database (Denmark)

    Christensen, Morten Lykkegaard; Bugge, Thomas Vistisen; Kirchheiner, Anders Løvenbalk

    that the production of filtrate also depends on the characteristic time for the filter cake solids to deform. This is formulated in the Terzaghi-Voigt model in which a secondary consolidation is introduced. The secondary consolidation may be visualized by plots of the relative cake deformation (U) v.s. the square...... root of time. Even more clearly it is demonstrated by plotting the liquid pressure at the cake piston interface v.s. the relative deformation (to be shown). The phenomenon of a secondary consolidation processes is in short called creep. Provided that the secondary consolidation rate is of the same......The classical filtration theory assumes a unique relationship between the local filter cake porosity and the local effective pressure. For a number of compressible materials, it has however been observed that during the consolidation stage this may not be the case. It has been found...

  2. Comparison of low stress creep properties of ferritic and austenitic creep resistant steels

    Czech Academy of Sciences Publication Activity Database

    Kloc, Luboš; Sklenička, Václav; Ventruba, J.

    319-321, - (2001), s. 774-778 ISSN 0921-5093. [International Conference on Strength of Materials /12./. Monterey, CA, USA, 27.08.2000-01.09.2000] R&D Projects: GA AV ČR IAA2041702; GA MŠk OC 522.40 Institutional research plan: CEZ:AV0Z2041904 Keywords : viscous creep * power-law creep * creep-resistant steel Subject RIV: JG - Metallurgy Impact factor: 0.978, year: 2001

  3. Etude des comportements rheologiques des melanges de farine ble ...

    African Journals Online (AJOL)

    Etude des comportements rheologiques des melanges de farine ble/sorgho sans tanins issue de trois nouvelles varietes cultivees au Senegal et mise au point de pains a base de farines composees (ble/sorgho)

  4. Instrumental performance of an etude after three methods of practice.

    Science.gov (United States)

    Vanden Ark, S

    1997-12-01

    For 80 fifth-grade students three practice conditions (mental, mental with physical simulation, and physical with singing) produced significant mean differences in instrumental performance of an etude. No significant differences were found for traditional, physical practice.

  5. Slow creep in soft granular packings.

    Science.gov (United States)

    Srivastava, Ishan; Fisher, Timothy S

    2017-05-14

    Transient creep mechanisms in soft granular packings are studied numerically using a constant pressure and constant stress simulation method. Rapid compression followed by slow dilation is predicted on the basis of a logarithmic creep phenomenon. Characteristic scales of creep strain and time exhibit a power-law dependence on jamming pressure, and they diverge at the jamming point. Microscopic analysis indicates the existence of a correlation between rheology and nonaffine fluctuations. Localized regions of large strain appear during creep and grow in magnitude and size at short times. At long times, the spatial structure of highly correlated local deformation becomes time-invariant. Finally, a microscale connection between local rheology and local fluctuations is demonstrated in the form of a linear scaling between granular fluidity and nonaffine velocity.

  6. Implications of Jeffreys-Lomnitz Transient Creep

    Science.gov (United States)

    Strick, Ellis

    1984-01-01

    In 1958 Jeffreys proposed a power law generalization of the logarithmic transient creep earlier attributed to Lomnitz. Although Jeffreys' power law form was admittedly defective in that it became unbounded at infinite time, he did apply it to the viscoelastic behavior of the earth-moon system. Since then it has been successfully applied by many investigators to mantle rehology and Chandler wobble. Experimental seismic studies indicate that most rock types exhibit the almost constant Q behavior which Lomnitz showed to be associated with his logarithmic creep. In this paper, we study not only the Q behavior related to Jeffreys' power law creep but also other mechanical properties such as a precise spring-dashpot ladder network realization are developed. In addition, a very simple physically realizable modification of this ladder network leads to a boundedness at long times of Jeffreys' creep in a manner which does not affect his successful application at finite times.

  7. Creep-fatigue of low cobalt superalloys

    Science.gov (United States)

    Halford, G. R.

    1982-01-01

    Testing for the low cycle fatigue and creep fatigue resistance of superalloys containing reduced amounts of cobalt is described. The test matrix employed involves a single high temperature appropriate for each alloy. A single total strain range, again appropriate to each alloy, is used in conducting strain controlled, low cycle, creep fatigue tests. The total strain range is based upon the level of straining that results in about 10,000 cycles to failure in a high frequency (0.5 Hz) continuous strain-cycling fatigue test. No creep is expected to occur in such a test. To bracket the influence of creep on the cyclic strain resistance, strain hold time tests with ore minute hold periods are introduced. One test per composition is conducted with the hold period in tension only, one in compression only, and one in both tension and compression. The test temperatures, alloys, and their cobalt compositions that are under study are given.

  8. Critical view on the creep modelling procedures

    Czech Academy of Sciences Publication Activity Database

    Kloc, Luboš

    2015-01-01

    Roč. 128, č. 4 (2015), s. 540-542 ISSN 0587-4246. [ISPMA 2014 - International Symposium on Physics of Materials /13./. Praha, 31.08.2014-04.09.2014] R&D Projects: GA MPO FR-TI4/406 Institutional support: RVO:68081723 Keywords : Creep * Creep deformation * Grain boundaries * Phase structure * Strain rate Subject RIV: JJ - Other Materials Impact factor: 0.525, year: 2015

  9. Numerically and experimentally analysis of creep

    International Nuclear Information System (INIS)

    Fontanive, J.A.

    1982-11-01

    The problems of creep in concrete are analyzed experimentally and numerically, comparing with classical methods and suggesting a numerical procedure for the solution of these problems. Firstly, fundamentals of viscoelasticity and its application to concrete behaviour representation are presented. Then the theories of Dischinger and Arutyunyan are studied, and a computing numerical solutions are compared in several examples. Finally, experiences on creep and relaxation are described, and its result are analyzed. Some coments on possible future developments are included. (Author) [pt

  10. Review of recent irradiation-creep results

    International Nuclear Information System (INIS)

    Coghlan, W.A.

    1982-05-01

    Materials deform faster under stress in the presence of irradiation by a process known as irradiation creep. This phenomenon is important to reactor design and has been the subject of a large number of experimental and theoretical investigations. The purpose of this work is to review the recent experimental results to obtain a summary of these results and to determine those research areas that require additional information. The investigations have been classified into four subgroups based on the different experimental methods used. These four are: (1) irradiation creep using stress relaxation methods, (2) creep measurements using pressurized tubes, (3) irradiation creep from constant applied load, and (4) irradiation creep experiments using accelerated particles. The similarity and the differences of the results from these methods are discussed and a summary of important results and suggested areas for research is presented. In brief, the important results relate to the dependence of creep on swelling, temperature, stress state and alloying additions. In each of these areas new results have been presented and new questions have arisen which require further research to answer. 65 references

  11. Creep analysis of silicone for podiatry applications.

    Science.gov (United States)

    Janeiro-Arocas, Julia; Tarrío-Saavedra, Javier; López-Beceiro, Jorge; Naya, Salvador; López-Canosa, Adrián; Heredia-García, Nicolás; Artiaga, Ramón

    2016-10-01

    This work shows an effective methodology to characterize the creep-recovery behavior of silicones before their application in podiatry. The aim is to characterize, model and compare the creep-recovery properties of different types of silicone used in podiatry orthotics. Creep-recovery phenomena of silicones used in podiatry orthotics is characterized by dynamic mechanical analysis (DMA). Silicones provided by Herbitas are compared by observing their viscoelastic properties by Functional Data Analysis (FDA) and nonlinear regression. The relationship between strain and time is modeled by fixed and mixed effects nonlinear regression to compare easily and intuitively podiatry silicones. Functional ANOVA and Kohlrausch-Willians-Watts (KWW) model with fixed and mixed effects allows us to compare different silicones observing the values of fitting parameters and their physical meaning. The differences between silicones are related to the variations of breadth of creep-recovery time distribution and instantaneous deformation-permanent strain. Nevertheless, the mean creep-relaxation time is the same for all the studied silicones. Silicones used in palliative orthoses have higher instantaneous deformation-permanent strain and narrower creep-recovery distribution. The proposed methodology based on DMA, FDA and nonlinear regression is an useful tool to characterize and choose the proper silicone for each podiatry application according to their viscoelastic properties. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Creep buckling problems in fast reactor components

    International Nuclear Information System (INIS)

    Ramesh, R.; Damodaran, S.P.; Chellapandi, P.; Chetal, S.C.; Bhoje, S.B.

    1995-01-01

    Creep buckling analyses for two important components of 500 M We Prototype Fast Breeder Reactor (PFBR), viz. Intermediate Heat Exchanger (IHX) and Inner Vessel (IV), are reported. The INCA code of CASTEM system is used for the large displacement elasto-plastic-creep analysis of IHX shell. As a first step, INCA is validated for a typical benchmark problem dealing with the creep buckling of a tube under external pressure. Prediction of INCA is also compared with the results obtained using Hoff's theory. For IV, considering the prohibitively high computational cost for the actual analysis, a simplified analysis which involves only large displacement elastoplastic buckling analysis is performed using isochronous stress strain curve approach. From both of these analysis is performed using isochronous stress strain curve approach. From both of these analysis, it has been inferred that creep buckling failure mode is not of great concern in the design of PFBR components. It has also been concluded from the analysis that Creep Cross Over Curve given in RCC-MR is applicable for creep buckling failure mode also. (author). 8 refs., 9 figs., 1 tab

  13. Study on the creep constitutive equation of Hastelloy X, (1)

    International Nuclear Information System (INIS)

    Suzuki, Kazuhiko; Mutoh, Yasushi

    1983-01-01

    In order to carry out the structural design of high temperature pipings, intermediate heat exchangers and isolating valves for a multipurpose high temperature gas-cooled reactor, in which coolant temperature reaches 1000 deg C, the creep characteristics of Hastelloy X used as the heat resistant material must be clarified. In addition to usual creep rupture life and the time to reach a specified creep strain, the dependence of creep strain curves on time, temperature and stress must be determined and expressed with equations. Therefore, using the creep data of Hastelloy X given in the literatures, the creep constitutive equation was made. Since the creep strain curves under the same test condition were different according to heats, the sensitivity analysis of the creep constitutive equation was performed. The form of the creep constitutive equation was determined to be Garofalo type. The result of the sensitivity analysis is reported. (Kako, I.)

  14. A creep life assessment method for boiler pipes using small punch creep test

    International Nuclear Information System (INIS)

    Izaki, Toru; Kobayashi, Toshimi; Kusumoto, Junichi; Kanaya, Akihiro

    2009-01-01

    The small punch creep (SPC) test is considered as a highly useful method for creep life assessment for high temperature plant components. SPC uses miniature-sized specimens and does not cause any serious sampling damages, and its assessment accuracy is at a high level. However, in applying the SPC test to the residual creep life assessment of the boiler in service, there are some issues to be studied. In order to apply SPC test to the residual creep life assessment of the 2.25Cr-1Mo steel boiler pipe, the relationship between uniaxial creep stress and the SPC test load has been studied. The virgin material, pre-crept, weldment and service aged samples of 2.25Cr-1Mo steel were tested. It was confirmed that the relationship between uniaxial creep stress and the SPC test load at the same rupture time can be described as a single straight line independent of test conditions and materials. Therefore a life assessment is possible by using SPC test in place of uniaxial creep tests. The creep life assessment using SPC was applied to actual thermal power plant components which are in service.

  15. The investigation of expanded polystyrene creep behaviour

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey

    2017-01-01

    Full Text Available The results obtained in long-term testing under constant compressive stress of the cut from the Slabs EPS 50/100 and EPS 150 with the density ranging from 15 to 24 kg/m3, which were manufactured by the same manufacturer by foaming EPS solid granules (beads in closed volume. The creep strain of the above described specimens was used as a criterion for estimating the deformability of the EPS slabs under long-term compressive stress. It was measured using special stands EN 1606, maintaining constant stress during the fixed time interval tn=122 days. Creep strains were determined by the methods described in EN 1606 for constant stress σc=0.35σ10% (compressive stress σ10% was determined in accordance with EN 826:2013. The long-term compressive stress measurement error did not exceed 1 %, while the creep strain measurement error was not larger than 0,005 mm. The tests were conducted at the ambient temperature of (23±2°С and relative humidity of (50±5 %.The long-term constant compressive load σc=0.35σ10%. The method of mathematical and statistical experimental design optimization models taking into account the thickness of specimens is proposed to determine the creep compliance Ic (tn the creep strain εc (tn and predictive point estimate of creep strain εc (T. Graphical interpretation of the abstained models is also presented. It should be noted that the abstained equations may be used in practice for estimating the creep strains at time tn=122 days and predictive estimates of εc (T for the load time of 10 years.

  16. Unified creep-plasticity model for halite

    International Nuclear Information System (INIS)

    Krieg, R.D.

    1980-11-01

    There are two national energy programs which are considering caverns in geological salt (NaCl) as a storage repository. One is the disposal of nuclear wastes and the other is the storage of oil. Both short-time and long-time structural deformations and stresses must be predictable for these applications. At 300K, the nominal initial temperature for both applications, the salt is at 0.28 of the melting temperature and exhibits a significant time dependent behavior. A constitutive model has been developed which describes the behavior observed in an extensive set of triaxial creep tests. Analysis of these tests showed that a single deformation mechanism seems to be operative over the stress and temperature range of interest so that the secondary creep data can be represented by a power of the stress over the entire test range. This simple behavior allowed a new unified creep-plasticity model to be applied with some confidence. The resulting model recognizes no inherent difference between plastic and creep strains yet models the total inelastic strain reasonably well including primary and secondary creep and reverse loadings. A multiaxial formulation is applied with a back stress. A Bauschinger effect is exhibited as a consequence and is present regardless of the time scale over which the loading is applied. The model would be interpreted as kinematic hardening in the sense of classical plasticity. Comparisons are made between test data and model behavior

  17. Irradiation creep in zirconium single crystals

    International Nuclear Information System (INIS)

    MacEwen, S.R.; Fidleris, V.

    1976-07-01

    Two identical single crystals of crystal bar zirconium have been creep tested in reactor. Both specimens were preirradiated at low stress to a dose of about 4 x 10 23 n/m 2 (E > 1 MeV), and were then loaded to 25 MPa. The first specimen was loaded with reactor at full power, the second during a shutdown. The loading strain for both crystals was more than an order of magnitude smaller than that observed when an identical unirradiated crystal was loaded to the same stress. Both crystals exhibited periods of primary creep, after which their creep rates reached nearly constant values when the reactor was at power. During shutdowns the creep rates decreased rapidly with time. Electron microscopy revealed that the irradiation damage consisted of prismatic dislocation loops, approximately 13.5 nm in diameter. Cleared channels, identified as lying on (1010) planes, were also observed. The results are discussed in terms of the current theories for flux enhanced creep in the light of the microstructures observed. (author)

  18. Analysis of Superheater Work Under Creep Conditions

    Directory of Open Access Journals (Sweden)

    Piotr Duda

    2015-03-01

    Full Text Available The aim of this article is work modelling of superheater SH3. It is made of the austenitic stainless steel Super 304H. Its design temperature T is 604 C, and the design pressure P acting on the inner surface of the pipes is 284 bar. The high temperature is the reason of the superheater work under creep conditions. In this article calculations of the optimally mounted coil superheater SH3 are presented. The calculations are carried out first on the basis of the applicable European standards and with the help of the Auto Pipe program. Then, calculations are performed using the ANSYS program based on conducted creep tests and proposed creep equation. The coefficients in creep equation are determined based on the research conducted at the Instytut Metalurgii Żelaza in Gliwice. The model approximates the creep strain as the function of time and stress and this function is presented in the form of a three-dimensional surface . The results of calculations by both methods will be compared and conclusions will be presented. The performed analyzes can estimate the superheater coil remnant life and the usage after the selected time of its operation.

  19. Non Newtonian gravity creeping flow

    International Nuclear Information System (INIS)

    Gratton, J.; Mahajan, S.M.; Minotti, F.

    1988-11-01

    We derive the governing equations for creeping gravity currents of non Newtonian liquids having a power law rheology, using a lubrication approximation. We consider unidirectional and axisymmetric currents. The equations differ from those for Newtonian liquids, being nonlinear in the spatial derivative of the thickness of the current. However, many solutions are closely analogous to those for Newtonian rheology; in particular the spreading relations can also be expressed as power laws of time, with exponents that depend on the rheological index. Similarity solutions for currents whose volume varies as a power of time are obtained. For the spread of a constant volume of liquid, analytic solutions are found. We also derive solutions of the waiting-time type, as well as the ones describing steady flows from a constant source to a sink. General travelling wave solutions are given, and analytic formulae for a simple case are derived. A phase plane formalism, that allows the systematic derivation of self similar solutions, is introduced. The application of the Boltzmann transform is briefly discussed. Present results are closely analogous to those for Newtonian liquids; all the solutions obtained here have their counterparts in Newtonian flows. This happens because the power law rheology, like the Newtonian constitutive relation, involves a single dimensional parameter. Thus one finds similarity solutions whenever the analogous Newtonian problem is self similar. Although the spreading relations are rheology-dependent, in most cases the dependence is rather weak. The present results may be of interest for geophysics since the lithosphere deforms according to an average power law rheology. (author). 17 refs

  20. Creep Properties of Walikukun (Schouthenia ovata Timber Beams

    Directory of Open Access Journals (Sweden)

    Ali Awaludin

    2016-09-01

    Full Text Available This study presents an evaluation of creep constants of Walikukun (Schoutheniaovata timber beams when rheological model of four solid elements, which is obtained byassembling Kelvin and Maxwell bodies in parallel configuration, was adopted. Creep behaviorobtained by this method was further discussed and compared with creep behavior developedusing phenomenological model of the previous study. Creep data of previous study was deformationmeasurement of Walikukun beams having cross-section of 15 mm by 20 mm with a clearspan of 550 mm loaded for three weeks period under two different room conditions: with andwithout Air Conditioner. Creep behavior given by both four solid elements model and phenomenological(in this case are power functions had good agreement during the period of creepmeasurement, but they give different prediction of creep factor beyond this period. The powerfunction of phenomenological model could give a reasonable creep prediction, while for the foursolid elements model a necessary modification is required to adjust its long-term creep behavior.

  1. Viscoelastic characterization of carbon fiber-epoxy composites by creep and creep rupture tests

    International Nuclear Information System (INIS)

    Farina, Luis Claudio

    2009-01-01

    One of the main requirements for the use of fiber-reinforced polymer matrix composites in structural applications is the evaluation of their behavior during service life. The warranties of the integrity of these structural components demand a study of the time dependent behavior of these materials due to viscoelastic response of the polymeric matrix and of the countless possibilities of design configurations. In the present study, creep and creep rupture test in stress were performed in specimens of unidirectional carbon fiber-reinforced epoxy composites with fibers orientations of 60 degree and 90 degree, at temperatures of 25 and 70 degree C. The aim is the viscoelastic characterization of the material through the creep curves to some levels of constant tension during periods of 1000 h, the attainment of the creep rupture envelope by the creep rupture curves and the determination of the transition of the linear for non-linear behavior through isochronous curves. In addition, comparisons of creep compliance curves with a viscoelastic behavior prediction model based on Schapery equation were also performed. For the test, a modification was verified in the behavior of the material, regarding the resistance, stiffness and deformation, demonstrating that these properties were affected for the time and tension level, especially in work temperature above the ambient. The prediction model was capable to represent the creep behavior, however the determination of the equations terms should be considered, besides the variation of these with the applied tension and the elapsed time of test. (author)

  2. Creep Rupture Life Prediction Based on Analysis of Large Creep Deformation

    Directory of Open Access Journals (Sweden)

    YE Wenming

    2016-08-01

    Full Text Available A creep rupture life prediction method for high temperature component was proposed. The method was based on a true stress-strain elastoplastic creep constitutive model and the large deformation finite element analysis method. This method firstly used the high-temperature tensile stress-strain curve expressed by true stress and strain and the creep curve to build materials' elastoplastic and creep constitutive model respectively, then used the large deformation finite element method to calculate the deformation response of high temperature component under a given load curve, finally the creep rupture life was determined according to the change trend of the responsive curve.The method was verified by durable test of TC11 titanium alloy notched specimens under 500 ℃, and was compared with the three creep rupture life prediction methods based on the small deformation analysis. Results show that the proposed method can accurately predict the high temperature creep response and long-term life of TC11 notched specimens, and the accuracy is better than that of the methods based on the average effective stress of notch ligament, the bone point stress and the fracture strain of the key point, which are all based on small deformation finite element analysis.

  3. Transitional Thermal Creep of Early Age Concrete

    DEFF Research Database (Denmark)

    Hauggaard, A. B.; Damkilde, L.; Hansen, Per Freiesleben

    1999-01-01

    Couplings between creep of hardened concrete and temperature/water effects are well-known. Both the level and the gradients in time of temperature or water content influence the creep properties. In early age concrete the internal drying and the heat development due to hydration increase the effect...... of these couplings. The purpose of this work is to set up a mathematical model for creep of concrete that includes the transitional thermal effect. The model governs both early age concrete and hardened concrete. The development of the material properties in the model is assumed to depend on the hydration process...... and the thermal activation of water in the microstructure. The thermal activation is assumed to be governed by the Arrhenius principle, and the activation energy of the viscosity of water is found applicable in the analysis of the experimental data. Changes in temperature create an imbalance in the microstructure...

  4. Documentation for the viscoplastic and creep program

    DEFF Research Database (Denmark)

    Bellini, Anna

    2004-01-01

    The purpose of this document is to summarize the work done in the workpackage 4 of the IDEAL (Integrated Development Routes for Optimized Cast Aluminium Components) project, financed by the EU in frame work 6 and born in collaboration with the automobile and foundry industries. The objective...... of this workpackage is to simulate creep behavior of aluminum cast samples subjected to high temperature. In this document a two-state variables unified model is applied in order to simulate creep behavior and time-dependent metallurgical changes. The fundamental assumption of the unified theory is that creep...... and viscoplasticity, which are both irreversible strains developed because of dislocations motion in the material structure, can be modelled through the implementation of a similar plastic strain velocity law, generally called flow rule. The document shows how to obtain the material data needed for the simulation...

  5. Transitional Thermal Creep of Early Age Concrete

    DEFF Research Database (Denmark)

    Hauggaard-Nielsen, Anders Boe; Damkilde, Lars; Freiesleben Hansen, Per

    1999-01-01

    of these couplings. The purpose of this work is to set up a mathematical model for creep of concrete which includes the transitional thermal effect. The model govern both early age concrete and hardened concrete. The development of the material properties in the model are assumed to depend on the hydration process......Couplings between creep of hardened concrete and temperature/water effects are well-known. Both the level and the gradients in time of temperature or water content influence the creep properties. In early age concrete the internal drying and the heat development due to hydration increase the effect...... and the thermal activation of the water in the microstructure. The thermal activation is assumed to be governed by the Arrhenius principle and the activation energy of the viscosity of water is found applicable in the analysis of experimental data. Changes in temperature create an imbalance in the microstructure...

  6. Creep fatigue design of FBR components

    International Nuclear Information System (INIS)

    Bhoje, S.B.; Chellapandi, P.

    1997-01-01

    This paper deals with the characteristic features of Fast Breeder Reactor (FBR) with reference to creep fatigue, current creep fatigue design approach in compliance with RCCMR (1987) design code, material data, effects of weldments and neutron irradiation, material constitutive models employed, structural analysis and further R and D required for achieving maturity in creep fatigue design of FBR components. For the analysis reported in this paper, material constitutive models developed based on ORNIb (Oak Ridge National Laboratory) and Chaboche viscoplastic theories are employed to demonstrate the potential of FBR components for higher plant temperatures and/or longer life. The results are presented for the studies carried out towards life prediction of Prototype Fast Breeder Reactor (PFBR) components. (author). 24 refs, 8 figs, 5 tabs

  7. Influence of the phase composition of refractory materials on creep

    OpenAIRE

    Terzić A.; Pavlović Lj.; Milutinović-Nikolić A.

    2006-01-01

    In this paper, the relationship between the creeping effect and mineralogical characteristics of the applied binding phase for various refractory materials (high-alumina materials, with high or low impurity content, tar bonded either magnesite or dolomite materials and silicate bonded chrom-magnesite materials) is presented. The mechanism of creeping is analyzed and the activation energy for creep for each investigated material is obtained and discussed. All investigated materials are creep s...

  8. Accelerated diffusion controlled creep of polycrystalline materials. Communication 1. Model of diffusion controlled creep acceleration

    International Nuclear Information System (INIS)

    Smirnova, E.S.; Chuvil'deev, V.N.

    1998-01-01

    The model is suggested which describes the influence of large-angle grain boundary migration on a diffusion controlled creep rate in polycrystalline materials (Coble creep). The model is based on the concept about changing the value of migrating boundary free volume when introducing dislocations distributed over the grain bulk into this boundary. Expressions are obtained to calculate the grain boundary diffusion coefficient under conditions of boundary migration and the parameter, which characterized the value of Coble creep acceleration. A comparison is made between calculated and experimental data for Cd, Co and Fe

  9. Contribution to the study of sputtering and damage of uranium dioxide by fast heavy ions; Contribution a l'etude de la pulverisation et de l'endommagement du dioxyde d'uranium par les ions lourds rapides

    Energy Technology Data Exchange (ETDEWEB)

    Schlutig, S

    2001-03-01

    Swift heavy ion-solid interaction leads in volume to track creation and on the surface to the ejection of particles into the vacuum. To learn more about initial mechanisms of track formation, we are focused on the sputtering of uranium dioxide by fast heavy ions. This present study is exclusively devoted to the influence of the electronic stopping power on the emission of neutral particles and especially on their angular distribution. These measurements are completed by those of the ions emitted from UO{sub 2} targets bombarded with swift heavy ions. The whole experimental results give access to: i) the nature of the sputtered particles; ii) the charge state of the emitted particles; iii) the direction of ejection of the sputtered particles ; iv) the sputtering yields deduced from the angular distributions. These results are compared to the prediction of the sputtering models proposed in the literature and it seems that the supersonic gas flow model is well suited to describe our results. Finally, the sputtering yields are compared with a set of earlier experimental data on uranium dioxide damage obtained by T. Wiss and we observe that only a small fraction of UO{sub 2} monolayers are sputtered. (author)

  10. The effect of creep damage formulation on crack tip fields, creep stress intensity factor and crack growth assessments

    Directory of Open Access Journals (Sweden)

    V. Shlyannikov

    2017-07-01

    Full Text Available Fields of stress, strain rate and process zone of a mode I creep crack growth are analyzed by employing damage evolution equations. Damage models for fracture of process zone represented by stress based formulation. Two expressions are presented to describe the stress-sensitive nature of multiaxial rupture behavior. Both damage free and defective creeping solids have been studied. The variation of creep stress and the crack-tip governing parameter in the form of creep In-integral with time and the evolution of creep damage were analyzed by using the FE-model. The effect of the introduced creep stress intensity factor as a function of creep time through the continuum damage mechanics of the creep crack growth are discussed in detail.

  11. A stochastic approach to anelastic creep

    International Nuclear Information System (INIS)

    Venkataraman, G.

    1976-01-01

    Anelastic creep or the time-dependent yielding or a material subjected to external stresses has been found to be of great importantance in technology in the recent years, particularly in engineering structures including nuclear reactors wherein structural members may be under stress. The physics aspects underlying this phenomenon is dealt with in detail. The basics of time-dependent elasticity, constitutive relation, network models, constitutive equation in the frequency domain and its mearurements, and stochastic approach to creep are discussed. (K.B.)

  12. Radiometric study of creep in ingot rolling

    International Nuclear Information System (INIS)

    Kubicek, P.; Zamyslovsky, Z.; Uherek, J.

    The radiometric study of creep during ingot rolling performed in the rolling mill of the Vitkovice Iron and Steel Works and the first results are described. Selected sites in 3 to 8 ton ingots were labelled with 2 to 3.7x10 5 Bq of 60 Co and after rolling into blocks, the transposition of the labelled sites of the ingots was investigated. The results indicate creep during rolling, local extension in certain sites under study and help to determine the inevitable bottom crop incurred in the forming. Finally, the requirements put on the radiometric apparatus for the next stages of technological research are presented. (author)

  13. Influence of relative humidity on tensile and compressive creep of ...

    African Journals Online (AJOL)

    This paper presents an experimental study on the influence of ambient relative humidity on tensile creep of plain concrete amended with Ground Granulated Blast - furnace Slag and compares it with its influence on compressive creep. Tensile and compressive creep tests were carried out on concrete specimens of 34.49 ...

  14. influence of relative humidity on tensile and compressive creep

    African Journals Online (AJOL)

    HOD

    This paper presents an experimental study on the influence of ambient relative humidity on tensile creep of plain concrete amended with Ground Granulated Blast-furnace Slag and compares it with its influence on compressive creep. Tensile and compressive creep tests were carried out on concrete specimens of ...

  15. Crack Tip Creep Deformation Behavior in Transversely Isotropic Materials

    International Nuclear Information System (INIS)

    Ma, Young Wha; Yoon, Kee Bong

    2009-01-01

    Theoretical mechanics analysis and finite element simulation were performed to investigate creep deformation behavior at the crack tip of transversely isotropic materials under small scale creep (SCC) conditions. Mechanical behavior of material was assumed as an elastic-2 nd creep, which elastic modulus ( E ), Poisson's ratio (v ) and creep stress exponent ( n ) were isotropic and creep coefficient was only transversely isotropic. Based on the mechanics analysis for material behavior, a constitutive equation for transversely isotropic creep behavior was formulated and an equivalent creep coefficient was proposed under plain strain conditions. Creep deformation behavior at the crack tip was investigated through the finite element analysis. The results of the finite element analysis showed that creep deformation in transversely isotropic materials is dominant at the rear of the crack-tip. This result was more obvious when a load was applied to principal axis of anisotropy. Based on the results of the mechanics analysis and the finite element simulation, a corrected estimation scheme of the creep zone size was proposed in order to evaluate the creep deformation behavior at the crack tip of transversely isotropic creeping materials

  16. Irradiation creep due to SIPA-induced growth

    International Nuclear Information System (INIS)

    Woo, C.H.

    1980-01-01

    An additional contribution to irradiation creep resulting from the stress-induced preferred adsorption (SIPA) effect is described - SIPA-induced growth (SIG). The mechanism of SIG is discussed and an expression for its contribution to irradiation creep developed. It is shown that SIG is very significant in comparison with SIPA. Enhancement of creep by swelling may also occur. (U.K.)

  17. Modelling of creep damage development in ferritic steels

    Energy Technology Data Exchange (ETDEWEB)

    Sandstroem, R. [Swedish Institute for Metals Research, Stockholm (Sweden)

    1998-12-31

    The physical creep damage, which is observed in fossil-fired power plants, is mainly due to the formation of cavities and their interaction. It has previously been demonstrated that both the nucleation and growth of creep cavities can be described by power functions in strain for low alloy and 12 % CrMoV creep resistant steels. It possible to show that the physical creep damage is proportional to the product of the number of cavities and their area. Hence, the physical creep damage can also be expressed in terms of the creep strain. In the presentation this physical creep damage is connected to the empirical creep damage classes (1-5). A creep strain-time function, which is known to be applicable to low alloy and 12 % CrMoV creep resistant steels, is used to describe tertiary creep. With this creep strain - time model the residual lifetime can be predicted from the observed damage. For a given damage class the remaining life is directly proportional to the service time. An expression for the time to the next inspection is proposed. This expression is a function of fraction of the total allowed damage, which is consumed till the next inspection. (orig.) 10 refs.

  18. Production response of lambs receiving creep feed while grazing ...

    African Journals Online (AJOL)

    Department of Agriculture (Western Cape)

    analysis of variance with treatment (creep feed or no creep feed) and birth status (single and twins) as main factors. Provision a ... At both locations, birth status had no effect on the production parameters for ewes or lambs. Keywords: Creep ... supplementation are of vital importance (De Villiers, 1991; Brand et al., 1999).

  19. Studies of Grain Boundaries in Materials Subjected to Diffusional Creep

    DEFF Research Database (Denmark)

    Nørbygaard, Thomas

    Grain boundaries in crystalline Cu(2%Ni) creep specimens have been studied by use of scanning and transmission electron microscopy in order to establish the mechanism of deformation. Creep rate measurements and dependencies were found to fit reasonably well with the model for diffusional creep...

  20. Plastic creep flow processes in fracture at elevated temperatures

    International Nuclear Information System (INIS)

    Rice, J.R.

    1979-01-01

    Recent theoretical developments on fracture at elevated temperature in the presence of overall plastic (dislocation) creep are discussed. Two topics are considered: stress fields at tips of macroscopic cracks in creeping solids; and diffusive growth of microscopic grain boundary cavities in creeping solids

  1. Nanoindentation creep versus bulk compressive creep of dental resin-composites.

    Science.gov (United States)

    El-Safty, S; Silikas, N; Akhtar, R; Watts, D C

    2012-11-01

    To evaluate nanoindentation as an experimental tool for characterizing the viscoelastic time-dependent creep of resin-composites and to compare the resulting parameters with those obtained by bulk compressive creep. Ten dental resin-composites: five conventional, three bulk-fill and two flowable were investigated using both nanoindentation creep and bulk compressive creep methods. For nano creep, disc specimens (15mm×2mm) were prepared from each material by first injecting the resin-composite paste into metallic molds. Specimens were irradiated from top and bottom surfaces in multiple overlapping points to ensure optimal polymerization using a visible light curing unit with output irradiance of 650mW/cm(2). Specimens then were mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. Following grinding and polishing, specimens were stored in distilled water at 37°C for 24h. Using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius), the nano creep was measured at a maximum load of 10mN and the creep recovery was determined when each specimen was unloaded to 1mN. For bulk compressive creep, stainless steel split molds (4mm×6mm) were used to prepare cylindrical specimens which were thoroughly irradiated at 650mW/cm(2) from multiple directions and stored in distilled water at 37°C for 24h. Specimens were loaded (20MPa) for 2h and unloaded for 2h. One-way ANOVA, Levene's test for homogeneity of variance and the Bonferroni post hoc test (all at p≤0.05), plus regression plots, were used for statistical analysis. Dependent on the type of resin-composite material and the loading/unloading parameters, nanoindentation creep ranged from 29.58nm to 90.99nm and permanent set ranged from 8.96nm to 30.65nm. Bulk compressive creep ranged from 0.47% to 1.24% and permanent set ranged from 0.09% to 0.38%. There was a significant (p=0.001) strong positive non-linear correlation (r(2)=0.97) between bulk

  2. Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy. Part I; Isothermal Creep

    Science.gov (United States)

    Raj, S. V.; Noebe, R. D.

    2013-01-01

    This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

  3. Tin dioxide: synthesis, characterization and study of the interactions with different polluting gases - application to DeNOx catalysis; Dioxyde d'etain: synthese, caracterisation et etude des interactions avec differents gaz polluants - application a la catalyse DeNOx

    Energy Technology Data Exchange (ETDEWEB)

    Sergent, N.

    2003-01-01

    Two high specific surface area tin dioxides after calcination at 600 degrees C under O{sub 2} have been synthesized: SnO{sub 2}-HNO{sub 3} (24 m{sup 2} g{sup -1}) and SnO{sub 2}-N{sub 2}H{sub 4} (101 m{sup 2} g{sup -1}). The surface of the 600 degrees C - calcined SnO{sub 2}-N{sub 2}H{sub 4} sample was found to be more hydroxylated than the 600 degrees C - calcined SnO{sub 2}-HNO{sub 3} one. The thermal treatment under O{sub 2} involves the formation of mono-ionized oxygen vacancies, leading to non-stoichiometric tin dioxides. A specific treatment like outgassing at temperatures above 300-400 degrees C, was found to be necessary to extract surface oxygen atoms. The CO adsorption at liquid N{sub 2} temperature on the SnO{sub 2}-N{sub 2}H{sub 4} sample has shown the existence of two cationic Sn{sup 4+} sites, having different Lewis acidities. Concerning the surface OH groups, it has been observed: i) hydroxyl which are inaccessible to CO, ii) weakly acidic surface hydroxyl and iii) surface hydroxyl having a weak Broensted acidity. Then, a study of the interactions between the 600 degrees C - calcined SnO{sub 2}-N{sub 2}H{sub 4} sample and various pollutant gases has been carried out by transmission FTIR spectroscopy. Carbon dioxide interacts with SnO{sub 2} surface, leading to CO{sub 2} species adsorbed on cationic sites together with carbonates and bicarbonates ad-species. Carbon monoxide involves the partial reduction of SnO{sub 2} surface by reaction of CO with surface oxygens to form carbonate species and CO{sub 2}. Interactions of SnO{sub 2} surface with NO{sub 2} have shown the formation of NO{sup +}, nitrite and nitrate ad-species. The NO adsorption on SnO{sub 2}-N{sub 2}H{sub 4} have shown the formation of electron donor species (nitrite and nitrate species) together with electron acceptor species (nitrosyl species). Finally, in the Selective Catalytic Reduction (SCR) of NO{sub x} by propene in oxygen excess, SnO{sub 2} was found to be active at high

  4. Creep testing and creep loading experiments on friction stir welds in copper at 75 deg C

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Henrik C.M.; Seitisleam, Facredin; Sandstroem, Rolf [Corrosion an d Metals Research Institute, Stockholm (Sweden)

    2007-08-15

    Specimens cut from friction stir welds in copper canisters for nuclear waste have been used for creep experiments at 75 deg C. The specimens were taken from a cross-weld position as well as heat affected zone and weld metal. The parent metal specimens exhibited longer creep lives than the weld specimens by a factor of three in time. They in turn were longer than those for the crossweld and HAZ specimens by an order of magnitude. The creep exponent was in the interval 50 to 69 implying that the material was well inside the power-law breakdown regime. The ductility properties expressed as reduction in area were not significantly different and all the rupture specimens demonstrated values exceeding 80%. Experiments were also carried out on the loading procedure of a creep test. Similar parent metal specimens and test conditions were used and the results show that the loading method has a large influence on the strain response of the specimen.

  5. Application of creep small punch testing in assessment of creep lifetime

    Czech Academy of Sciences Publication Activity Database

    Dobeš, Ferdinand; Milička, Karel

    510-511, Sp. Iss. (2009), s. 440-443 ISSN 0921-5093. [International Conference of Creep and Fracture of Engineering Materials and Structures /11./. Bad Berneck, 04.05.2008-09.05.2008] R&D Projects: GA AV ČR 1QS200410502 Institutional research plan: CEZ:AV0Z20410507 Keywords : Small punch tests * Creep * Rupture * Chromium steel * Extrapolation methods Subject RIV: JG - Metallurgy Impact factor: 1.901, year: 2009

  6. Analysis of available creep and creep-rupture data for commercially heat-treated alloy 718

    International Nuclear Information System (INIS)

    Booker, M.K.; Booker, B.L.P.

    1980-03-01

    The Ni-Cr-Fe-Nb alloy 718 is a widely used material in elevated- temperature applications. Currently, it is approved by the American Society of Mechanical Engineers ASME Boiler and Pressure Vessel Code only as a bolting material for elevated-temperature nuclear service. This report presents analyses of available creep and creep-rupture data for commercially heat-treated alloy 718 toward the development of allowable stress levels for this material in general elevated-temperature nuclear service. Available data came from 14 heats of bar, plate, and forging material over the temperature range from 538 to 704 degrees C. The longest rupture time encompassed by the data was almost 87,000 h. Generalized regression analyses were performed to yield an analytical expression for rupture life as a function of stress and temperature. Heat-to-heat variations were accounted for by ''lot-centering'' the data. Effects of different solution heat treatment temperatures (T s ) were accounted for by normalizing the creep stresses to the data for T s = 954 degrees C. Thus, the results are strictly applicable only for material with this solution treatment. Time and strain to tertiary creep were predicted as functions of rupture life. Creep strain-time data were represented by normalization to the time and strain to tertiary creep and development of ''master creep curves.'' The results allow estimation of time-dependent allowable stress per American Society of Mechanical Engineers Code Class N-47, and the creep strain-time relationships can be used to develop isochronous stress-strain curves. 29 refs., 44 figs., 14 tabs

  7. Study of volumetric properties (PVT) of mixtures made of light hydrocarbons (C1-C4), carbon dioxide and hydrogen sulfide - Experimental measurements through a vibrating tube densimeter and modelling; Etude des proprietes volumetriques (PVT) d'hydrocarbures legers (C1-C4), du dioxyde de carbone et de l'hydrogene sulfure. Mesures par densimetrie a tube vibrant et modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Rivollet, F.

    2005-12-15

    Various pollutant contents (i.e. carbon dioxide, hydrogen sulphide or other sulphur products) are found in produced oils. These latter must undergo a number of transformations and purifications. The design and dimensioning of the corresponding units can well be optimized only if one has reliable and accurate data about phase equilibria and volumetric properties and of course reliable and accurate modeling. This work was devoted partly to measurements of volumetric properties on three binary mixtures (ethane - hydrogen sulphide, ethane - propane and carbon dioxide - hydrogen sulphide). These measurements were carried out using equipment, comprising a vibrating tube densimeter (Paar, model DMA 512 P), which was especially designed and built for this work. The binary mixtures were studied in the 253 to 363 K temperature range from at pressures up to either 20 or 40 MPa. Two calibration methods of the vibrating tube were used: the FPMC method (Forced Path Mechanical Calibration) described in the literature and an original method containing neural network, developed herein. The study undertaken about the modeling of volumetric properties made it possible to highlight the inadequacy of the traditional use of cubic equations of state to represent simultaneously volumetric properties and phase equilibria. Among the equations of state investigated, a close attention however was paid to cubic equations of state because of their very great use in the oil field. A new tool was found to adapt cubic equations of state to the simultaneous and satisfactory representation of volumetric properties and phase equilibria. It concerns the coupling of the cubic Redlich-Kwong-Soave equation of state with volume correction through a neural network. This new model was tested successfully, it makes it possible to benefit from the existing work of representation of phase equilibria (mixing rules and interaction coefficients) while improving calculation of the volumetric data.

  8. Creep rupture behavior of welded Grade 91 steel

    Energy Technology Data Exchange (ETDEWEB)

    Shrestha, Triratna [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Basirat, Mehdi [Department of Mechanical Engineering, University of Idaho, Moscow, ID 83844 (United States); Alsagabi, Sultan; Sittiho, Anumat [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Charit, Indrajit, E-mail: icharit@uidaho.edu [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Potirniche, Gabriel P. [Department of Mechanical Engineering, University of Idaho, Moscow, ID 83844 (United States)

    2016-07-04

    Creep rupture behavior of fusion welded Grade 91 steel was studied in the temperature range of 600 – 700 °C and at stresses of 50–200 MPa. The creep data were analyzed in terms of the Monkman-Grant relation and Larson-Miller parameter. The creep damage tolerance factor was used to identify the origin of creep damage. The creep damage was identified as the void growth in combination with microstructural degradation. The fracture surface morphology of the ruptured specimens was studied by scanning electron microscopy and deformed microstructure examined by transmission electron microscopy, to further elucidate the rupture mechanisms.

  9. Factors influencing the creep strength of hot pressed beryllium

    International Nuclear Information System (INIS)

    Webster, D.; Crooks, D.D.

    1975-01-01

    The parameters controlling the creep strength of hot pressed beryllium block have been determined. Creep strength was improved by a high initial dislocation density, a coarse grain size, and a low impurity content. The impurities most detrimental to creep strength were found to be aluminum, magnesium, and silicon. A uniform distribution of BeO was found to give creep strength which was inferior to a grain boundary distribution. The creep strength of very high purity, hot isostatically pressed beryllium was found to compare favorably with that of other more commonly used high temperature metals

  10. Influence of the phase composition of refractory materials on creep

    Directory of Open Access Journals (Sweden)

    Terzić A.

    2006-01-01

    Full Text Available In this paper, the relationship between the creeping effect and mineralogical characteristics of the applied binding phase for various refractory materials (high-alumina materials, with high or low impurity content, tar bonded either magnesite or dolomite materials and silicate bonded chrom-magnesite materials is presented. The mechanism of creeping is analyzed and the activation energy for creep for each investigated material is obtained and discussed. All investigated materials are creep sensitive under investigated conditions and have similar activation energies for creep except high-alumina refractories with a low impurity content.

  11. Concrete creep at transient temperature: constitutive law and mechanism

    International Nuclear Information System (INIS)

    Chern, J.C.; Bazant, Z.P.; Marchertas, A.H.

    1985-01-01

    A constitutive law which describes the transient thermal creep of concrete is presented. Moisture and temperature are two major parameters in this constitutive law. Aside from load, creep, cracking, and thermal (shrinkage) strains, stress-induced hygrothermal strains are also included in the analysis. The theory agrees with most types of test data which include basic creep, thermal expansion, shrinkage, swelling, creep at cyclic heating or drying, and creep at heating under compression or bending. Examples are given to demonstrate agreement between the theory and the experimental data. 15 refs., 6 figs

  12. Compressive creep of hot pressed silicon carbide

    Energy Technology Data Exchange (ETDEWEB)

    Silva, C.R.M., E-mail: cosmeroberto@gmail.com [Universidade de Brasilia (UnB), Campus Darcy Ribeiro, Brasilia CEP 70736-020, DF (Brazil); Nono, M.C.A. [Instituto de Nacional de Pesquisas Espaciais (INPE-LAS) (Brazil); Reis, D.A.P.; Hwang, M.K. [Instituto de Aeronautica e Espaco (IAE) (Brazil)

    2010-07-15

    Silicon carbide has a good match of chemical, mechanical and thermal properties and therefore is considered an excellent structural ceramic for high temperature applications. The aim of the present work is compressive creep evaluation of liquid phase sintered silicon carbide with aluminum and rare earth oxide as sintering aids. Rare earth oxides are possible additives considering their highly refractory remnant grain-boundary phase and lower synthesis costs compared to high purity rare earth. Samples were prepared with silicon carbide powder (90 wt%) and aluminum oxide (5 wt%) plus rare earth oxide (5 wt%) additions. Powders were mixed, milled and hot pressed at 1800 deg. C in argon atmosphere. Compressive creep tests were carried out under stress from 150 to 300 MPa and temperatures from 1300 to 1400 deg. C. At lower creep test temperatures, the obtained stress exponent values were correlated to mechanisms based on diffusion. At intermediate temperatures, grain-boundary sliding becomes operative, accommodated by diffusion. At higher temperatures cavities are discernible. Oxidation reactions and ionic diffusion result on surface oxidized layer, grain-boundary amorphous and intergranular crystalline Al{sub 6}Si{sub 2}O{sub 13}, {delta}-Y{sub 2}Si{sub 2}O{sub 7} and YAG phases. In this case cavitation and amorphous phases redistribution enhance grain-boundary sliding, not accommodated by diffusion. Coalescence occurs at triple point and multigrain-junctions, with subsequent strain rate acceleration and cavitational creep.

  13. Viscous creep in metals at intermediate temperatures

    Czech Academy of Sciences Publication Activity Database

    Kloc, Luboš; Fiala, J.

    2005-01-01

    Roč. 43, č. 2 (2005), s. 105-112 ISSN 0023-432X R&D Projects: GA AV ČR(CZ) IAA2041101 Institutional research plan: CEZ:AV0Z20410507; CEZ:AV0Z2041904 Keywords : creep * heat resistant steel Subject RIV: JG - Metallurgy Impact factor: 0.973, year: 2005

  14. Creep measurements on curing epoxy systems

    DEFF Research Database (Denmark)

    Kammer, Charlotte; Szabo, Peter

    1998-01-01

    The chemical curing of a stoichiometric mixture of the diglycidyl ether of bisphenol A and a 1,3-bis-(aminomethyl)-cyclohexane is studied.Creep experiments are combined with measurements in a Differential Scanning Calorimeter (DSC) to determine the change in bulk viscosity due to network formation....

  15. Creep of granulated loose-fill insulation

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    with SP-Building Physics in Sweden and VTT Building Technology in Finland. For the round robin test a cellulosic fibre insulation material was used. The proposed standardised method for creep tests and theories are limited to cases when the granulated loose-fill material is exposed to a constant......, Organisation for Testing in Scandinavia funded the Nordtest....

  16. Plasticity - a limiting case of creep

    International Nuclear Information System (INIS)

    Cords, H.; Kleist, G.; Zimmermann, R.

    1986-11-01

    The present work is an attempt to develop further the so-called unified theory for viscoplastic constitutive equations as used for metals or metal alloys. Typically, in similar approaches creep strains and plastic strains are derived from one common stress-strain relationship for inelastic strain rates employing an internal stress function as a back stress. Some novel concepts concerning the definition of the internal stress, plastic yielding and material hardening have been introduced, formulated mathematically and tested for correspondence with a standard type of materials behaviour. As a result of the investigations a system of simultaneous differential equations is defined which has been used to elaborate a common view on a number of different material effects observed in creep and plasticity i.e. normal and inverted primary creep, recoverable creep, incubation time and anelasticity in stress reduction, negative stress relaxation, plastic yielding, perfect plasticity, negative strain rate sensitivity, serrated flow, strain hardening in monotonic and cyclic loading. The theoretical approach is mainly based on a lateral contraction movement not following rigidly the longitudinal extension of the material specimen by a prescribed constant value of Poisson's ratio as usual, but following the axial extension in a process of drag which allows for retardation and which simultaneously impedes the longitudinal straining. (orig.) [de

  17. Creep properties of aluminium processed by ECAP

    Czech Academy of Sciences Publication Activity Database

    Král, Petr; Dvořák, Jiří; Jäger, Aleš; Kvapilová, Marie; Horita, Z.; Sklenička, Václav

    2016-01-01

    Roč. 54, č. 6 (2016), s. 441-451 ISSN 0023-432X R&D Projects: GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 ; RVO:68378271 Keywords : equal channel angular pressing (ECAP) * aluminium * ultrafine-grained microstructure * creep Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) Impact factor: 0.366, year: 2016

  18. Constant structure creep experiments on aluminium

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel

    2011-01-01

    Roč. 49, č. 5 (2011), s. 307-318 ISSN 0023-432X R&D Projects: GA AV ČR IAA2041203 Institutional research plan: CEZ:AV0Z20410507 Keywords : mechanical properties * high temperature deformation * creep * aluminium Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.451, year: 2011

  19. timber joists subjected to creep-rupture

    African Journals Online (AJOL)

    user

    Wood experiences a significant loss of strength and stiffness when loaded over period of time. This phenomenon is known as creep-rupture. Several models were developed for the estimation of the reduction of load carrying capacity of timber with time. In this paper, the results of time dependent structural reliability analysis ...

  20. A constitutive equation of creep based on recoverable creep hardening range

    International Nuclear Information System (INIS)

    Murakami, Sumio; Ohno, Nobutada

    1982-01-01

    In case of the stress reverse test of 304 stainless steel under constant stress, the creep curve after stress reverse is not much different from that for the initial state, accordingly, the state of hardening of the material is restored almost to that in the initial state by stress reverse. Creep depends on past loading history, and essentially is anisotropic phenomenon. In this study, by extending the strain hardening theory to general multi-axial stress condition, a constitutive formula for creep without any difficulty was determined. For the purpose, as the main change of microscopic structure at the time of stress reverse in mono-axial creep, the effect of the reactivation of passive dislocations was considered. At this time, the range of recoverable creep hardening was assumed, in which irreversible dislocation arrangement does not occur after stress reverse. In order to examine the propriety of this theory, the multi-axial creep deformation, of which the principal stress direction changes periodically, was calculated by the derived constitutive formula, and the result was compared with the experimental result of 304 stainless steel tube at 650 deg C and the theoretical result of ORNL. (Kako, I.)

  1. Uniaxial creep behavior of V-4Cr-4Ti alloy

    International Nuclear Information System (INIS)

    Natesan, K.; Soppet, W.K.; Purohit, A.

    2002-01-01

    We are undertaking a systematic study at Argonne National Laboratory to evaluate the uniaxial creep behavior of V-Cr-Ti alloys in a vacuum environment as a function of temperature in the range of 650-800 deg. C and at applied stress levels of 75-380 MPa. Creep strain in the specimens is measured by a linear-variable-differential transducer, which is attached between the fixed and movable pull rods of the creep assembly. Strain is measured at sufficiently frequent intervals during testing to define the creep strain/time curve. A linear least-squares analysis function is used to ensure consistent extraction of minimum creep rate, onset of tertiary creep and creep strain at the onset of tertiary creep. Creep test data, obtained at 650, 700, 725 and 800 deg. C, showed power-law creep behavior. Extensive analysis of the tested specimens is conducted to establish hardness profiles, oxygen content and microstructural characteristics. The data are also quantified by the Larson-Miller approach, and correlations are developed to relate time to rupture, onset of tertiary creep, times for 1% and 2% strain, exposure temperature and applied stress

  2. Nonlinear creep damage constitutive model for soft rocks

    Science.gov (United States)

    Liu, H. Z.; Xie, H. Q.; He, J. D.; Xiao, M. L.; Zhuo, L.

    2017-02-01

    In some existing nonlinear creep damage models, it may be less rigorous to directly introduce a damage variable into the creep equation when the damage variable of the viscous component is a function of time or strain. In this paper, we adopt the Kachanov creep damage rate and introduce a damage variable into a rheological differential constitutive equation to derive an analytical integral solution for the creep damage equation of the Bingham model. We also propose a new nonlinear viscous component which reflects nonlinear properties related to the axial stress of soft rock in the steady-state creep stage. Furthermore, we build an improved Nishihara model by using this new component in series with the correctional Nishihara damage model that describes the accelerating creep, and deduce the rheological constitutive relation of the improved model. Based on superposition principle, we obtain the damage creep equation for conditions of both uniaxial and triaxial compression stress, and study the method for determining the model parameters. Finally, this paper presents the laboratory test results performed on mica-quartz schist in parallel with, or vertical to the schistosity direction, and applies the improved Nishihara model to the parameter identification of mica-quartz schist. Using a comparative analysis with test data, results show that the improved model has a superior ability to reflect the creep properties of soft rock in the decelerating creep stage, the steady-state creep stage, and particularly within the accelerating creep stage, in comparison with the traditional Nishihara model.

  3. Creep-fatigue damage assessment by subsequent fatigue straining

    International Nuclear Information System (INIS)

    Yaguchi, M.; Nakamura, T.; Ishikawa, A.; Asada, Y.

    1993-01-01

    A series of creep-fatigue tests has been conducted with Modified 9Cr-1Mo steel at 600 deg. C in a high vacuum environment of 0.1mPa to assess an accumulation of creep-fatigue damage. In these tests, each test specimen has been subjected to prior creep-fatigue loading followed by subsequent fatigue loading or prior fatigue loading followed by subsequent creep-fatigue loading. A linear summation of cumulative damage of fatigue and creep life fraction is smaller than unity for the former case, and larger than unity for the latter case. SEM observation was conducted and it was shown that in the case of prior creep-fatigue loading, crack mode transforms from transgranular to intergranular type with the increase of the number of cycles of prior creep-fatigue loading, while crack mode is generally intergranular in the case of prior fatigue loading. (author)

  4. Soil creep and historic landscape changes

    Science.gov (United States)

    Lucke, Bernhard

    2017-04-01

    Many erosion models assume that soil sediments are transported grain-by-grain, and thus calculate loss and deposition according to parameters such as bulk density and average grain size. However, clay-rich soils, such as the widespread Red Mediterranean Soils or Terrae Rossae that are often found near important archaeological sites, can behave differently. This is illustrated by a case study of historic landscape changes in Jordan, where evidence for soil creep as main process of soil movement was found in the context of ancient cemeteries. Due to a dominance of smectites, the Red Mediterranean Soils in this area shrink and form cracks during the dry period. Because of the cracks and underlying limestone karst, they can swallow strong rains without high erosion risk. However, when water-saturated, these soils expand and can start creeping. Buried geoarchaeological features like small water channels on formerly cleared rocks suggest that soils can move a few cm uplslope when wet, and buried graves illustrate that soil creep can create new level surfaces, sealing cavities but not completely filling them. Such processes seem associated with slumping and earth flows as instable rocks might collapse under the weight of a creeping soil. While it is very difficult to measure such processes, landscape archaeology offers at least an indirect approach that could be suited to estimate the scale and impact of soil creep. Analogies with modern rainfalls, including record levels of precipitation during the winter 1991/1992, indicate that similar levels of soil moisture have not been reached during times of modern instrumental rainfall monitoring. This suggests that very strong deluges must have occurred during historical periods, that could potentially cause tremendous damage to modern infrastructure if happening again.

  5. Finite element creep buckling analysis of circular cylindrical shell under axial compression taking account of creep damage

    Science.gov (United States)

    Hagihara, Seiya; Miyazaki, Noriyuki

    1998-05-01

    Cylindrical shells are utilized as structural elements of nuclear power plants, heat exchangers or pressure vessels, which are operated under elevated temperature. Creep buckling is one of the failure modes of structures at elevated temperature. In some experiments conducted by other authors, axially compressive cylindrical shells with a large ratio of radius to thickness were observed to buckle with circumferential waves. It is observed that the circumferential waves occur due to bifurcation buckling. But, the critical time and the minimum loading for bifurcation buckling obtained from calculations of finite element analyses are not in very good agreement with those of the experiments. One of the reasons for the disagreement is considered to be that the creep constitutive equations employed in many previous analyses represent the steady creep. The creep phenomena usually have primary creep period, steady creep one and tertiary creep one. A creep strain - time relation through the three periods can be simulated by using a constitutive equation based on creep damage mechanics. In the present analysis, we analyzed the bifurcation creep buckling of circular cylindrical shells subjected to axial compression by the use of the finite element method taking account of the creep damage mechanics proposeol by of Kachanov-Rabotonov.

  6. PENULISAN ETUDE-ETUDE MUSIK TALEMPONG UNGGAN (Sebuah Usaha Pembelajaran Musik Tradisi Berbasis Literatur

    Directory of Open Access Journals (Sweden)

    Asri MK

    2014-12-01

    Full Text Available “Talempong unggan”, a traditional music from Minangkabau community particularly in Unggan, Sumpur Kudus, Sijunjung Regency, West Sumatera Indonesia is classified into genre of “talempong duduak” (rea. Due to its special musical concept and the playing technics, this traditional music is selected as a practising course in the Karawitan Department of Indonesian Institute of Art (ISI Padang Panjang since 1993 till now. In a system of class learning with many students, Talempong Unggan definitely needs supporting methods and learning technics suitable for the course where the students can reach their maximum skills. All the melody of “talempong unggan” that has been made as a material of practice is transcribed to the system of numeric notation and rhythm motive of “gendang” and “aguang” which is written into signs and special notation. All of qualitative data is formulated into finding methods, technics and etude of learning ensamble of Talempong Unggan the traditional music that learned in Karawitan Department of ISI Padang Panjang. Key words: Talempong Unggan, Methods, Technics, Etude

  7. Etude des interactions entre les differents acteurs des interventions ...

    African Journals Online (AJOL)

    Etude des interactions entre les differents acteurs des interventions sous directives communautaires et changements obtenus au Benin et au Togo. P.V. Malou Adom, Ch. P. Makoutode, T Gnaro, A.R. Ouro-Koura, E.M. Ouendo, G Napo-Koura, M Makoutode ...

  8. Influence of phosphorus on the creep ductility of copper

    International Nuclear Information System (INIS)

    Sandström, Rolf; Wu, Rui

    2013-01-01

    Around 1990 it was discovered that pure copper could have extra low creep ductility in the temperature interval 180–250 °C. The material was intended for use in canisters for nuclear waste disposal. Although extra low creep ductility was not observed much below 180 °C and the temperature in the canister will never exceed 100 °C, it was feared that the creep ductility could reach low values at lower temperatures after long term exposure. If 50 ppm phosphorus was added to the copper the low creep ductility disappeared. A creep cavitation model is presented that can quantitatively describe the cavitation behaviour in uniaxial and multiaxial creep tests as well as the observed creep ductility for copper with and without phosphorus. A so-called double ledge model has been introduced that demonstrates why the nucleation rate of creep cavities is often proportional to the creep rate. The phosphorus agglomerates at the grain boundaries and limits their local deformation and thereby reduces the formation and growth of cavities. This explains why extra low creep ductility does not occur in phosphorus alloyed copper

  9. Irradiation creep, stress relaxation and a mechanical equation of state

    International Nuclear Information System (INIS)

    Foster, J.P.

    1976-01-01

    Irradiation creep and stress relaxation data are available from the United Kingdom for 20 percent CW M316, 20 percent CW FV 548 and FHT PE16 using pure torsion in the absence of swelling at 300 0 C. Irradiation creep models were used to calculate the relaxation and permanent deflection of the stress relaxation tests. Two relationships between irradiation creep and stress relaxation were assessed by comparing the measured and calculated stress relaxation and permanent deflection. The results show that for M316 and FV548, the stress relaxation and deflection may be calculated using irradiation creep models when the stress rate term arising from the irradiation creep model is set equal to zero. In the case of PE16, the inability to calculate the stress relaxation and permanent deflection from the irradiation creep data was attributed to differences in creep behavior arising from lot-to-lot variations in alloying elements and impurity content. A modification of the FV548 and PE16 irradiation creep coefficients was necessary in order to calculate the stress relaxation and deflection. The modifications in FV548 and PE16 irradiation creep properties reduces the large variation in the transient or incubation parameter predicted by irradiation creep tests for M316, FV548 and PE16

  10. An anisotropic tertiary creep damage constitutive model for anisotropic materials

    International Nuclear Information System (INIS)

    Stewart, Calvin M.; Gordon, Ali P.; Ma, Young Wha; Neu, Richard W.

    2011-01-01

    When an anisotropic material is subject to creep conditions and a complex state of stress, an anisotropic creep damage behavior is observed. Previous research has focused on the anisotropic creep damage behavior of isotropic materials but few constitutive models have been developed for anisotropic creeping solids. This paper describes the development of a new anisotropic tertiary creep damage constitutive model for anisotropic materials. An advanced tensorial damage formulation is implemented which includes both material orientation relative to loading and the degree of creep damage anisotropy in the model. A variation of the Norton-power law for secondary creep is implemented which includes the Hill's anisotropic analogy. Experiments are conducted on the directionally-solidified bucket material DS GTD-111. The constitutive model is implemented in a user programmable feature (UPF) in ANSYS FEA software. The ability of the constitutive model to regress to the Kachanov-Rabotnov isotropic tertiary creep damage model is demonstrated through comparison with uniaxial experiments. A parametric study of both material orientation and stress rotation are conducted. Results indicate that creep deformation is modeled accurately; however an improved damage evolution law may be necessary. - Highlights: → The deformation of anisotropic creeping solid is directionally dependent. → Few constitutive models have been developed to deal with anisotropic behavior. → A transversely-isotropic nickel base superalloy, DS GTD-111, is studied. → A vector constitutive model based on the Kachanov-Rabotnov formulation is developed. → The new model accurately models deformation at various orientations.

  11. Creep of Posidonia Shale at Elevated Pressure and Temperature

    Science.gov (United States)

    Rybacki, E.; Herrmann, J.; Wirth, R.; Dresen, G.

    2017-12-01

    The economic production of gas and oil from shales requires repeated hydraulic fracturing operations to stimulate these tight reservoir rocks. Besides simple depletion, the often observed decay of production rate with time may arise from creep-induced fracture closure. We examined experimentally the creep behavior of an immature carbonate-rich Posidonia shale, subjected to constant stress conditions at temperatures between 50 and 200 °C and confining pressures of 50-200 MPa, simulating elevated in situ depth conditions. Samples showed transient creep in the semibrittle regime with high deformation rates at high differential stress, high temperature and low confinement. Strain was mainly accommodated by deformation of the weak organic matter and phyllosilicates and by pore space reduction. The primary decelerating creep phase observed at relatively low stress can be described by an empirical power law relation between strain and time, where the fitted parameters vary with temperature, pressure and stress. Our results suggest that healing of hydraulic fractures at low stresses by creep-induced proppant embedment is unlikely within a creep period of several years. At higher differential stress, as may be expected in situ at contact areas due to stress concentrations, the shale showed secondary creep, followed by tertiary creep until failure. In this regime, microcrack propagation and coalescence may be assisted by stress corrosion. Secondary creep rates were also described by a power law, predicting faster fracture closure rates than for primary creep, likely contributing to production rate decline. Comparison of our data with published primary creep data on other shales suggests that the long-term creep behavior of shales can be correlated with their brittleness estimated from composition. Low creep strain is supported by a high fraction of strong minerals that can build up a load-bearing framework.

  12. Creep Behavior of Posidonia Shale at Elevated Pressure and Temperature

    Science.gov (United States)

    Rybacki, E.; Herrmann, J.; Wirth, R.; Dresen, G.

    2017-12-01

    Unconventional reservoir rocks are usually stimulated by repeated hydraulic fracturing operations. However, the production rate often decays with time that may arise from creep-induced fracture closure by proppant embedment. To examine experimentally the creep behavior of shales, we deformed immature carbonate-rich Posidonia shale at constant stress conditions and elevated temperatures between 50° and 200°C and confining pressures of 50 to 200 MPa. Samples showed transient creep in the semibrittle regime with high deformation rates at high differential stress, high temperature, and low confinement. Strain was mainly accommodated by deformation of the weak organic matter and phyllosilicates and by pore space reduction. At relatively low stress the samples deformed in the primary creep regime with continuously decelerating strain rate. The relation between strain and time can be described by an empirical power law equation, where the fitted parameters vary with temperature, pressure and stress. Our results suggest that healing of hydraulic fractures at low stresses by creep-induced proppant embedment is unlikely within a creep period of several years. At high differential stress (85-90% of the triaxial strength), as may be expected in situ at contact areas due to stress concentrations, the shale showed secondary creep, followed by tertiary creep until failure. In this regime, stress corrosion may induce microcrack propagation and coalescence. Secondary creep rates were also described by a power law that predicts faster fracture closure rates than for primary creep and likely contributes to production rate decline. Comparison of our data with published primary creep data on other shales suggest that the long-term creep behavior of shales can be correlated to their brittleness estimated from composition. Low creep strain is supported by a high fraction of strong minerals that can build up a load-bearing framework.

  13. Transient effects in friction fractal asperity creep

    CERN Document Server

    Goedecke, Andreas

    2013-01-01

    Transient friction effects determine the behavior of a wide class of mechatronic systems. Classic examples are squealing brakes, stiction in robotic arms, or stick-slip in linear drives. To properly design and understand mechatronic systems of this type, good quantitative models of transient friction effects are of primary interest. The theory developed in this book approaches this problem bottom-up, by deriving the behavior of macroscopic friction surfaces from the microscopic surface physics. The model is based on two assumptions: First, rough surfaces are inherently fractal, exhibiting roughness on a wide range of scales. Second, transient friction effects are caused by creep enlargement of the real area of contact between two bodies. This work demonstrates the results of extensive Finite Element analyses of the creep behavior of surface asperities, and proposes a generalized multi-scale area iteration for calculating the time-dependent real contact between two bodies. The toolset is then demonstrated both...

  14. Creep rupture behavior of Stirling engine materials

    Science.gov (United States)

    Titran, R. H.; Scheuerman, C. M.; Stephens, J. R.

    1985-01-01

    The automotive Stirling engine, being investigated jointly by the Department of Energy and NASA Lewis as an alternate to the internal combustion engine, uses high-pressure hydrogen as the working fluid. The long-term effects of hydrogen on the high temperature strength properties of materials is relatively unknown. This is especially true for the newly developed low-cost iron base alloy NASAUT 4G-A1. This iron-base alloy when tested in air has creep-rupture strengths in the directionally solidified condition comparable to the cobalt base alloy HS-31. The equiaxed (investment cast) NASAUT 4G-A1 has superior creep-rupture to the equiaxed iron-base alloy XF-818 both in air and 15 MPa hydrogen.

  15. The effect of dissolved magnesium on creep of calcite II: transition from diffusion creep to dislocation creep

    Science.gov (United States)

    Xu, Lili; Renner, Jörg; Herwegh, Marco; Evans, Brian

    2009-03-01

    We extended a previous study on the influence of Mg solute impurity on diffusion creep in calcite to include deformation under a broader range of stress conditions and over a wider range of Mg contents. Synthetic marbles were produced by hot isostatic pressing (HIP) mixtures of calcite and dolomite powders for different intervals (2-30 h) at 850°C and 300 MPa confining pressure. The HIP treatment resulted in high-magnesian calcite aggregates with Mg content ranging from 0.5 to 17 mol%. Both back-scattered electron images and chemical analysis suggested that the dolomite phase was completely dissolved, and that Mg distribution was homogeneous throughout the samples at the scale of about two micrometers. The grain size after HIP varied from 8 to 31 μm, increased with time at temperature, and decreased with increasing Mg content (>3.0 mol%). Grain size and time were consistent with a normal grain growth equation, with exponents from 2.4 to 4.7, for samples containing 0.5-17.0 mol% Mg, respectively. We deformed samples after HIP at the same confining pressure with differential stresses between 20 and 200 MPa using either constant strain rate or stepping intervals of loading at constant stresses in a Paterson gas-medium deformation apparatus. The deformation tests took place at between 700 and 800°C and at strain rates between 10-6 and 10-3 s-1. After deformation to strains of about 25%, a bimodal distribution of large protoblasts and small recrystallized neoblasts coexisted in some samples loaded at higher stresses. The deformation data indicated a transition in mechanism from diffusion creep to dislocation creep. At stresses below 40 MPa, the strength was directly proportional to grain size and decreased with increasing Mg content due to the reductions in grain size. At about 40 MPa, the sensitivity of log strain rate to log stress, ( n), became greater than 1 and eventually exceeded 3 for stresses above 80 MPa. At a given strain rate and temperature, the stress at

  16. Shark skin effect in creeping films

    OpenAIRE

    Scholle, M.; Aksel, N.

    2006-01-01

    If a body in a stream is provided with small ridges aligned in the local flow direction, a remarkable drag reduction can be reached under turbulent flow conditions. This surprising phenomenon is called the 'shark skin effect'. We demonstrate, that a reduction of resistance can also be reached in creeping flows if the ridges are aligned perpendicular to the flow direction. We especially consider in gravity-driven film flows the effect of the bottom topography on the mean transport velocity.

  17. Leidenfrost gas ratchets driven by thermal creep.

    Science.gov (United States)

    Würger, Alois

    2011-10-14

    We show that thermal creep is at the origin of the recently discovered Leidenfrost ratchet, where liquid droplets float on a vapor layer along a heated sawtooth surface and accelerate to velocities of up to 40  cm/s. As the active element, the asymmetric temperature profile at each ratchet summit rectifies the vapor flow in the boundary layer. This mechanism works at low Reynolds number and provides a novel tool for controlling gas flow at nanostructured surfaces.

  18. Finite element analysis of nonlinear creeping flows

    International Nuclear Information System (INIS)

    Loula, A.F.D.; Guerreiro, J.N.C.

    1988-12-01

    Steady-state creep problems with monotone constitutive laws are studied. Finite element approximations are constructed based on mixed Petrov-Galerkin formulations for constrained problems. Stability, convergence and a priori error estimates are proved for equal-order discontinuous stress and continuous velocity interpolations. Numerical results are presented confirming the rates of convergence predicted in the analysis and the good performance of this formulation. (author) [pt

  19. Anisotropy of creep resistance in extruded magnesium

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel; Dobeš, Ferdinand; Peréz, P.; Garcés, G.; Adeva, P.

    2009-01-01

    Roč. 61, č. 12 (2009), s. 1109-1112 ISSN 1359-6462 R&D Projects: GA ČR GA106/06/1354 Grant - others:Ministry of Science and Education of Spain(ES) MAT2006-11731CO2-01 Institutional research plan: CEZ:AV0Z20410507 Keywords : Magnesium * Creep * Texture * Extrusion Subject RIV: JG - Metallurgy Impact factor: 2.949, year: 2009

  20. Magnetic field annealing for improved creep resistance

    Science.gov (United States)

    Brady, Michael P.; Ludtka, Gail M.; Ludtka, Gerard M.; Muralidharan, Govindarajan; Nicholson, Don M.; Rios, Orlando; Yamamoto, Yukinori

    2015-12-22

    The method provides heat-resistant chromia- or alumina-forming Fe-, Fe(Ni), Ni(Fe), or Ni-based alloys having improved creep resistance. A precursor is provided containing preselected constituents of a chromia- or alumina-forming Fe-, Fe(Ni), Ni(Fe), or Ni-based alloy, at least one of the constituents for forming a nanoscale precipitate MaXb where M is Cr, Nb, Ti, V, Zr, or Hf, individually and in combination, and X is C, N, O, B, individually and in combination, a=1 to 23 and b=1 to 6. The precursor is annealed at a temperature of 1000-1500.degree. C. for 1-48 h in the presence of a magnetic field of at least 5 Tesla to enhance supersaturation of the M.sub.aX.sub.b constituents in the annealed precursor. This forms nanoscale M.sub.aX.sub.b precipitates for improved creep resistance when the alloy is used at service temperatures of 500-1000.degree. C. Alloys having improved creep resistance are also disclosed.

  1. Creep and Viscoelastic Behaviour of Human Dentin

    Directory of Open Access Journals (Sweden)

    T.Jafarzadeh

    2004-03-01

    Full Text Available Statement of Problem: Biomechanics of the human dentition is inherently complex.Purpose: The aim of this study is to investigate, in vitro, the creep and the recovery of dentin under static uniaxial compressive stress conditions.Materials and Methods: Specimens of cylindrical morphology were prepared from recently extracted non-carious lower molar teeth, such that the average tubule orientation was axial. Slides of mid- coronal dentin (parallel surfaces, height 1.8 mm were sectionedwith a slow speed diamond saw and then cut into cylindrical discs. Specimens were stored at 4ºC for 24h to restabilize water content. Creep data were then measured by LVDT axially in water for periods of 2h load + 2h recovery on 4 separate groups (n=6: at two stresses (10 & 18 MPa and at two temperatures: 37 & 60ºC. Maximum creep strain, permanent set,strain recovery and initial compressive modulus were reported.Results: Compliance values were also calculated and slight non-linearity found at 60ºC.Two-way ANOVA was performed on results. Dentin exhibited a linear viscoelastic response under 'clinical' compressive stress levels , with a maximum strain ~ 1% and highrecoverability: permanent set<0.3%.Conclusion: This established a performance standard for viscoelastic stability of restorative biomaterials, replacing human dentin.

  2. Experimental studies of fiber concrete creep

    Directory of Open Access Journals (Sweden)

    Korneeva Irina

    2017-01-01

    Full Text Available The results of two-stage experimental studies of the strength and deformation characteristics of fibrous concrete reinforced with steel fiber. In the experiments we used steel fiber with bent ends, which practically does not form "hedgehogs", which allows to achieve an even distribution of the fiber by volume. At the first stage, the cube and prismatic strength, deformability at central compression, a number of special characteristics are determined: water absorption, frost resistance, abrasion; the optimal percentage of fiber reinforcement and the maximum size of the coarse aggregate fraction were selected. Fiber reinforcement led to an increase in the strength of concrete at compression by 1,35 times and an increase in the tensile strength at bending by 3,4 times. At the second stage, the creep of fibrous concrete and plain concrete of similar composition at different stress levels was researched. Creep curves are plotted. It is shown that the use of fiber reinforcement leads to a decrease in creep strain by 21 to 30 percent, depending on the stress level.

  3. Creep as a mechanism for sealing amalgams.

    Science.gov (United States)

    Osborne, John W

    2006-01-01

    Dental amalgam seals itself over time. The reduction of microleakage in amalgam restorations has been explained by corrosion products filling in the interface gap between amalgam and tooth structure in order to seal the restoration interface. This concept has been widely accepted; yet, curiously, there is little research supporting this theory. The creep mechanism may be a plausible alternative to explaining why microleakage is reduced over time in amalgam restorations. Amalgam restorations are confined to the fixed space of the cavity preparation; expansion of the amalgam through internal phase changes in this confined area must be relieved. The resultant creep-expansion of the amalgam restoration fills in the tooth/amalgam interface gap. Once the interfacial gap is filled and amalgam has made intimate contact with the cavity wall, the dental amalgam slides along the tooth preparation plane as predicted by classic metallurgical studies. The results of the creep of amalgam have been observed clinically as the extrusion of amalgam from the cavity preparation. This explanation for amalgam sealing the tooth/amalgam gap fits many clinical observations and certain research data.

  4. Steady-State Creep of Asphalt Concrete

    Directory of Open Access Journals (Sweden)

    Alibai Iskakbayev

    2017-02-01

    Full Text Available This paper reports the experimental investigation of the steady-state creep process for fine-grained asphalt concrete at a temperature of 20 ± 2 °С and under stress from 0.055 to 0.311 MPa under direct tension and was found to occur at a constant rate. The experimental results also determined the start, the end point, and the duration of the steady-state creep process. The dependence of these factors, in addition to the steady-state creep rate and viscosity of the asphalt concrete on stress is satisfactorily described by a power function. Furthermore, it showed that stress has a great impact on the specific characteristics of asphalt concrete: stress variation by one order causes their variation by 3–4.5 orders. The described relations are formulated for the steady-state of asphalt concrete in a complex stressed condition. The dependence is determined between stress intensity and strain rate intensity.

  5. Experimental verification of creep analyses for prestressed concrete reactor vessels

    International Nuclear Information System (INIS)

    Aoyagi, Y.; Abe, H.; Ohnuma, H.

    1977-01-01

    The authors proposed a new method of creep analysis based on the theory of strain hardening, which assumes that accumulated creep at a given time influences the creep after that. This method was applied to calculate step-by-step the behaviors of uniaxial creep of concrete under variable temperatures and stresses, creep in reinforced concrete specimens and the behaviors of prestressed concrete beams under themal gradients. The experimental and calculated results agreed fairly well. Further, this method was incorporated in the finite element creep analysis for the prestressed concrete hollow cylinder and the full scale model. The calculated strain changes with time pursued closely those obtained by experiments. The above led to the conclusion that from the viewpoint of both accuracy and computation time the strain hardening method proposed by the authors may be judged advantageous for practical usages

  6. Creep stresses in a spherical shell under steady state temperature

    Science.gov (United States)

    Verma, Gaurav; Rana, Puneet

    2017-10-01

    The paper investigates the problem of creep of a spherical structure under the influence of steady state temperature. The problem of creep in spherical shell is solved by using the concept of generalized strain measures and transition hypothesis given by Seth. The problem has reduced to non-linear differential equation for creep transition. This paper deals with the non-linear behaviour of spherical shell under thermal condition. The spherical shell structures are easily vulnerable to creep, shrinkage and thermal effects; a thorough understanding of their time-dependent behaviour has been fully established. The paper aims to provide thermal creep analysis to enhance the effective design and long life of shells, and a theoretical model is developed for calculating creep stresses and strains in a spherical shell with purpose. Results obtained for the problem are depicted graphically.

  7. Creep behaviour of macro glass fibre reinforced concrete beams

    Science.gov (United States)

    Löber, P.; Heiden, B.; Holschemacher, K.

    2017-09-01

    This paper aims to present a creep study on structural concrete reinforced with macro glass fibres and wants to contribute to the understanding of creep behaviour of fibre reinforced concrete (FRC). Fibre reinforced concrete beams have been subjected to bending and tested in cracked state under defined stress levels. Therefore, a four-point-bending test setup was chosen and the creep period was 372d. The aim was to determine creep coefficients and to test residual strength values afterwards. Results show a dependence of residual strength and applied stress level. It turned out, that the beams failed due to tertiary creep at stress levels between 65 and 70% of residual crack load at 0.5 mm pre-crack deflection. Nevertheless, all remaining specimens showed increased loads after creep period. Finally, the evaluation is conducted in comparison to other fibre types.

  8. Fatigue and creep at variable temperature. Time dependence forecasting

    International Nuclear Information System (INIS)

    Felsen, M.F.; Mottot, M.; Petrequin, P.

    1984-03-01

    Structure materials for nuclear reactors undergo different types of mechanical and thermal stresses for period reaching 300 000 hours. Rapid change of temperature, stress, frequency can occurs in case of accident. Determination of mechanical properties (elongation, creep, fatigue...) of materials for structure dimensioning requires extrapolation of fatigue and creep tests. The comparison of results obtained on steel 316 shows that for creep forecastings agreement is good between the different methods but it is not the case for creep fatigue. For creep in variable conditions, agreement between experiments and calculus is good only in some cases. For fatigue test with samples previously tested for creep, or vice versa, results depend upon the damage evaluation [fr

  9. MICROSTRUCTURE AND MECHANICAL PROPERTIES DEGRADATION OF CrMo CREEP RESISTANT STEEL OPERATING UNDER CREEP CONDITIONS

    Directory of Open Access Journals (Sweden)

    Ján Micheľ

    2011-07-01

    Full Text Available In this contribution microstructure degradation of a steam tube is analysed. The tube is made of CrMo creep resistant steel and was in service under creep conditions at temperature 530°C and calculated stress level in the tube wall 46.5 MPa. During service life in the steel gradual micro structure changes were observed, first pearlite spheroidization, precipitation, coagulation and precipitate coarsening. Despite the fact that there were evident changes in the micro structure the strength and deformation properties of the steel (Re, Rm, A5, Z, the resistance to brittle fracture and the creep strength limit, were near to unchanged after 2.1x10 5 hours in service. The steam tube is now in service more than 2.6x10 5 h.

  10. Analysis of Simple Creep Stress Calculation Methods for Creep Life Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jun Min; Lee, Han Sang; Kim, Yun Jae [Korea Univ., Daejeon (Korea, Republic of)

    2017-08-15

    Creep analysis takes much more time than elastic or elastic-plastic analysis. In this study, we conducted elastic and elastic-plastic analysis and compared the results with creep analysis results. In the elastic analysis, we used primary stress, which can be classified by the Mα-tangent method and stress intensities recommended in the ASME code. In the elastic-plastic analysis, we calculated the parameters recommended in the R5 code. For the FE models, a bending load, uniaxial load, and biaxial load were applied to the cross shaped welded plate, and a bending load and internal pressure were applied to the elbow pipe. To investigate the element size sensitivity, we conducted FE analysis for various element sizes for the cases where bending load was applied to the cross shaped welded plate. There was no significant difference between the creep.

  11. Stability of MC Carbide Particles Size in Creep Resisting Steels

    Directory of Open Access Journals (Sweden)

    Vodopivec, F.

    2006-01-01

    Full Text Available Theoretical analysis of the dependence microstructure creep rate. Discussion on the effects of carbide particles size and their distribution on the base of accelerated creep tests on a steel X20CrMoV121 tempered at 800 °C. Analysis of the stability of carbide particles size in terms of free energy of formation of the compound. Explanation of the different effect of VC and NbC particles on accelerated creep rate.

  12. Heated mine room and pillar secondary creep response

    International Nuclear Information System (INIS)

    Tillerson, J.R.; Dawson, P.R.

    1980-04-01

    Heated salt mine room and pillar simulations have been performed to provide information regarding parameters affecting room closure rates to designers of radioactive waste isolation facilities. A coupled secondary creep and heat transfer formulation with large strain capabilities was used to assess the effects of variations in creep law parameters, thermal properties, imposed boundary conditions, temporal integration, and meshing resolution on room closure rates. Results indicate that the greatest effect results from variations in parameters appearing in the creep constitutive equation

  13. Application of regression analysis to creep of space shuttle materials

    International Nuclear Information System (INIS)

    Rummler, D.R.

    1975-01-01

    Metallic heat shields for Space Shuttle thermal protection systems must operate for many flight cycles at high temperatures in low-pressure air and use thin-gage (less than or equal to 0.65 mm) sheet. Available creep data for thin sheet under those conditions are inadequate. To assess the effects of oxygen partial pressure and sheet thickness on creep behavior and to develop constitutive creep equations for small sets of data, regression techniques are applied and discussed

  14. Creep behavior of materials for high-temperature reactor application

    International Nuclear Information System (INIS)

    Schneider, K.; Hartnagel, W.; Iischner, B.; Schepp, P.

    1984-01-01

    Materials for high-temperature gas-cooled reactor (HTGR) application are selected according to their creep behavior. For two alloys--Incoloy-800 used for the live steam tubing of the thorium high-temperature reactor and Inconel-617 evaluated for tubings in advanced HTGRs--creep curves are measured and described by equations. A microstructural interpretation is given. An essential result is that nonstable microstructures determine the creep behavior

  15. Control of Early Age Concrete. Phase 3: Creep in Concrete

    DEFF Research Database (Denmark)

    Hauggaard-Nielsen, Anders Boe; Damkilde, Lars; Hansen, Per Freiesleben

    1997-01-01

    The mechanical properties of the "Road Directorate Concrete" at early ages are studied. Creep in tension at 24 and 72 maturity hours are measured on dogbone shaped specimens. The development of tensile modulus of elasticity and strength are measured with a method developed here. The results...... are compared to compression values and splitting strengths. It is found that the properties of creep in tension are similar to the properties in compression. Further the influence form temperature on creep is found to be significant....

  16. Multi-axial Creep and the LICON Methodology for Accelerated Creep Testing

    Energy Technology Data Exchange (ETDEWEB)

    Bowyer, William H. [Meadow End Farm, Farnham (United Kingdom)

    2006-05-15

    The copper-Iron canister for disposal of nuclear waste in the Swedish Programme has a design life exceeding 100,000 years. Whilst the operating temperature (100 deg C max.) and operating stress (50 MPa max.) are modest, the very long design life does require that the likely creep performance of the canister should be investigated. Many studies have been carried out by SKB but these have all involved very short duration tests at relatively high stresses. The process of predicting canister creep life by extrapolation of data from such tests has been challenged for two main reasons. The first is that the deformation and failure mechanisms in the tests employed are different from the mechanism expected under service conditions and the second is that the extrapolation is extreme. It has been recognised that there is usually scope for some increase in test temperatures and stresses which will accelerate the development of creep damage without compromising the use of extrapolation for life prediction. Cane demonstrated that in steels designed for high temperature and pressure applications, conditions of multi-axial stressing could lead to increases or decreases in the rate of damage accumulation without changing the damage mechanism. This provided a third method for accelerating creep testing which has been implemented as the LICON method. This report aims to explain the background to the LICON method and its application to the case of the copper canister. It seems likely that the method could be used to improve our knowledge of the creep resistance of the copper canister. Multiplication factors that may be achieved by the technique could be increased by attention to specimen design but an extensive and targeted programme of data collection on creep of copper would still be needed to implement the method to best advantage.

  17. Multi-axial Creep and the LICON Methodology for Accelerated Creep Testing

    International Nuclear Information System (INIS)

    Bowyer, William H.

    2006-05-01

    The copper-Iron canister for disposal of nuclear waste in the Swedish Programme has a design life exceeding 100,000 years. Whilst the operating temperature (100 deg C max.) and operating stress (50 MPa max.) are modest, the very long design life does require that the likely creep performance of the canister should be investigated. Many studies have been carried out by SKB but these have all involved very short duration tests at relatively high stresses. The process of predicting canister creep life by extrapolation of data from such tests has been challenged for two main reasons. The first is that the deformation and failure mechanisms in the tests employed are different from the mechanism expected under service conditions and the second is that the extrapolation is extreme. It has been recognised that there is usually scope for some increase in test temperatures and stresses which will accelerate the development of creep damage without compromising the use of extrapolation for life prediction. Cane demonstrated that in steels designed for high temperature and pressure applications, conditions of multi-axial stressing could lead to increases or decreases in the rate of damage accumulation without changing the damage mechanism. This provided a third method for accelerating creep testing which has been implemented as the LICON method. This report aims to explain the background to the LICON method and its application to the case of the copper canister. It seems likely that the method could be used to improve our knowledge of the creep resistance of the copper canister. Multiplication factors that may be achieved by the technique could be increased by attention to specimen design but an extensive and targeted programme of data collection on creep of copper would still be needed to implement the method to best advantage

  18. Creep and creep rupture properties of cladding tube (type 316) in high temperature sodium

    International Nuclear Information System (INIS)

    Atsumo, H.

    1977-01-01

    The thin walled small sized seamless AISI 316 steel tubes, which are designated to be domestically used as the fuel cladding tube for sodium cooled fast breeder reactors in Japan, are irradiated in the following sodium of high temperature in the range of 370 deg. C to 700 deg. C, and receive gradually increased internal pressure caused by the fission produced gas generating from the nuclear fuel burn-up inside the cladding tube. Consequently, the creep behavior of fuel cladding tubes under a high temperature sodium environment is an important problem which must be determined and clarified together with their characteristic features under irradiation and in air. In relation to the creep performance of fuel cladding tubes made of AISI 316 steel and other comparable austenitic stainless steels, hardly any studies are found that are made systematically to examine the effect of sodium with sodium purity as parameter or any comparative studies with in-air data at various different temperatures. The present research work was aimed to obtain certain basic design data relating to in-sodium creep performance of the domestic made fuel cladding tubes for fast breeder reactors, and also to gain further date as considered necessary under several sodium conditions. That is, together with establishment of the technology for tensile creep test and internal pressure creep rupture test in flowing sodium of high temperature, a series of tests and studies were performed on the trial made cladding tubes of AISI Type-316 steel. In the first place, two kinds of purity conditions of sodium, close to the actual reactor-operating condition, (oxygen concentration of 10 ppm and 5 ppm respectively) were established, and then uniaxial tensile creep test and rupture test under various temperatures were performed and the resulting data were compared and evaluated against the in-air data. Then, secondly, an internal pressure creep rupture test was conducted under a single purity sodium environment

  19. Creep fracture and creep-fatigue fracture in ceramics and ceramic composites

    International Nuclear Information System (INIS)

    Suresh, S.

    1993-01-01

    This paper summarizes recent advances in the areas of subcritical crack growth in ceramics subjected to static and cyclic loads at elevated temperatures. Attention is devoted to the specific role of pre-existing and in-situ-formed glass films in influencing creep fracture and creep-fatigue fracture. Experimental results on the effects of cyclic frequency and load ratio, along with detailed transmission electron microscopy of crack-tip and crack-wake damage are highlighted. Some general conclusions are drawn about the dependence of high-temperature damage tolerance on interfacial glass films and about the susceptibility of ceramic materials to cyclic fatigue fracture

  20. Implementing Formative Assessment in Engineering Education: The Use of the Online Assessment System Etude

    Science.gov (United States)

    Dopper, Sofia M.; Sjoer, Ellen

    2004-01-01

    This article describes the possibilities offered by the online assessment system Etude to achieve the benefits of formative assessment. In order to find out the way this works in practice, we carried out an experiment with the use of Etude for formative assessment in the course on collaborative report writing. Results show that online formative…

  1. Nondestructive evaluation of creep-fatigue damage: an interim report

    International Nuclear Information System (INIS)

    Nickell, R.E.

    1977-02-01

    In view of the uncertainties involved in designing against creep-fatigue failure and the consequences of such failures in Class 1 nuclear components that operate at elevated temperature, the possibility of intermittent or even continuous non-destructive examination of these components has been considered. In this interim report some preliminary results on magnetic force and ultrasonic evaluation of creep-fatigue damage in an LMFBR steam generator material are presented. These results indicate that the non-destructive evaluation of pure creep damage will be extremely difficult. A set of biaxial creep-fatigue tests that are designed to discriminate between various failure theories is also described

  2. Creep behavior of Ti3Al-Nb intermetallic alloys

    International Nuclear Information System (INIS)

    Yu, T.H.; Yue, W.J.; Koo, C.H.

    1997-01-01

    It is well known that Ti 3 Al-Nb alloys are potential materials for aerospace applications. The creep property is an important consideration when materials are used at high temperature. In this article, the effect of microstructure of Ti-25Al-10Nb alloy on the creep property was investigated, and the creep property of Ti-25Al-10Nb alloy modified by small addition of silicon 0.2 at.% or carbon 0.1 at.% was observed. The alloy with the addition of molybdenum to replace part of niobium 2 at.% was also studied. The experimental results show that the furnace-cooled Ti-25Al-10Nb alloy has superior creep resistance to the air-cooled Ti-25Al-10Nb alloy at 200 MPa, but exhibits poor creep resistance at 250 MPa or above. Small addition of silicon to the Ti-25Al-10Nb alloy may increase creep resistance. Small addition of carbon to the Ti-25Al-10Nb alloy may reduce creep resistance but raise rupture strain. Molybdenum is the most effective alloying element to increase creep resistance for the Ti-25Al-10Nb alloy. The creep mechanism of Ti-25Al-10Nb alloy is governed by dislocation climb. (orig.)

  3. Long-term creep test with finite elements

    International Nuclear Information System (INIS)

    Argyris, J.H.; Szimmat, J.; Willam, K.J.

    1975-01-01

    Following a presentation of concrete creep, a brief summary of the direct and incremental calculation methods for long-term creep behaviour is given. In addition, a survey on the methods of the inner state variables is given which, on the one hand, gives a uniform framework for the various formulations of concrete creep, and on the other hand leads to a computable calculation method. Two examples on long-term creep behaviour illustrate the application field of the calculation method. (orig./LH) [de

  4. STRENGTH SHRINKAGE AND CREEP OF CONCRETE IN TENSION AND COMPRESSION

    Directory of Open Access Journals (Sweden)

    S A Kristiawan

    2006-01-01

    Full Text Available Strength, shrinkage and creep of concrete in tension and compression have been determined and the relationship between those properties was studied. Direct tensile tests were applied to measure those properties in tension. The relationship of creep in tension and compression was determined based on the measurement of creep at similar stress and similar stress/strength ratio. It is found that concrete deforms more in tension than in compression. Except for concrete with a higher water/cement ratio, the use of pulverised fuel ash, ground granulated blast furnace slag, superplasticizer and shrinkage reducing admixture has no effect on strength. However, they affect creep and shrinkage of concrete.

  5. microstructure change in 12 % Cr steel during creep

    International Nuclear Information System (INIS)

    Winatapura, D. S.; Panjaitan, E.; Arslan, A.; Sulistioso, G.S.

    1998-01-01

    The microstructure change in steel containing of 12% Cr or DIN X20CrMoV 12 1 during creep has been studied by means of optical microscopy and Transmission Electron Microscope (TEM). The creep testing at 650 o C was conducted under constant load of 650 Mpa. The heat treatment of the specimen before creep testing was austenization, followed by tempering for 2 hours. The obtained microstructure was tempered martensitic. This microstructure consisted of the martensite laths, and distributed randomly in the matrix. During tempering, chromium carbide particles of Cr 7 C 6 less than 0,2 μmin-size were precipitated on or and in the subgrain and lath martensite grain boundary. During creep testing those particles transformed and precipitated as chrome carbide precipitates of Cr 23 C 6 . At the secondary creep stage, the void formation occurred, and then it developed into the creep cracks. At tertiary creep stage for 3554 hours, the specimen was failure. The creep cracks were informs of transgranular and intergranular modes which propagated almost perpendicular to the stress axis. From this observation, it is suggested that tempering caused the ductility of martensitic microstructure, which increased the creep resistant or Cr 12% steel

  6. Creep behaviour of Cu-30 percent Zn at intermediate temperatures

    Science.gov (United States)

    Raj, S. V.

    1991-01-01

    The present, intermediate-temperature (573-823 K) range investigation of creep properties for single-phase Cu-30 percent Zn alpha-brass observed inverse, linear, and sigmoidal primary-creep transients above 573 K under stresses that yield minimum creep rates in the 10 to the -7th to 2 x 10 to the -4th range; normal primary creep occurred in all other conditions. In conjunction with a review of the pertinent literature, a detailed analysis of these data suggests that no clearly defined, classes M-to-A-to-M transition exists in this alloy notwithstanding the presence of both classes' characteristics under nominally similar stresses and temperatures.

  7. Creep deflection analysis of fuel channels in CANDU nuclear reactors

    International Nuclear Information System (INIS)

    Pettigrew, M.J.; Lambert, S.B.

    1980-01-01

    This paper presents an analysis of the creep deflection of fuel channel assemblies. The analysis considers the following factors: anisotropy of zirconium alloys; non-uniform creep rates due to the neutron flux distribution; asymmetry due to temperature gradients along the tube; effect of possible axial forces; effect of nominal slopes at the rolled joints; and, non-linearities due to nominal assembly clearances. Furthermore the problem is statically indeterminate and time dependent since, as creep deflection occurs, the reaction forces at the support points and the bending moment distribution change with time. The relations between bending creep and the creep behaviour of the material are first established. The deflection is obtained by double integration of both the elastic and creep components of the tube curvature. Simultaneous equations for deformation at each support point are formulated. These are solved exactly for each discrete time interval yielding the reaction forces and the bending moment distribution. The process is repeated until the design life is reached. The creep component of deformation is integrated with time. The analysis is implemented in a dedicated computer code which is easy to use and very efficient. The analysis is illustrated by examples. The effects of several parameters such as number of spacer supports, axial loading, temperature asymmetry and assembly tolerance are presented. It is concluded that creep deflection is not a major problem in fuel channels. By proper analysis, the channels can be designed so that their life is not limited by creep deflection. (auth)

  8. Creep characteristics of precipitation hardened carbon free martensitic alloys

    International Nuclear Information System (INIS)

    Muneki, S.; Igarashi, M.; Abe, F.

    2000-01-01

    A new attempt has been demonstrated using carbon free Fe-Ni-Co martensitic alloys strengthened by Laves phase such as Fe 2 W or Fe 2 Mo to achieve homogeneous creep deformation at high temperatures under low stress levels. Creep behavior of the alloys is found to be completely different from that of the conventional high-Cr ferritic steels. The alloys exhibit gradual change in the creep rate with strain both in the transient and acceleration creep regions, and give a larger strain for the minimum creep rate. In these alloys the creep deformation takes place very homogeneously and no heterogeneous creep deformation is enhanced even at low stress levels. The minimum creep rates of the Fe-Ni-Co alloys at 700 C are found to be much lower than that of the conventional steel, which is due to fine dispersion strengthening useful even at 700 C in these alloys. It is thus concluded that the Fe-Ni-Co martensite strengthened by Laves phase is very useful to increase the creep resistance at elevated temperatures over 650 C. (orig.)

  9. Creep rupture of structures subjected to variable loading and temperature

    International Nuclear Information System (INIS)

    Wojewodzki, W.

    1975-01-01

    The service life of structures operating under the conditions of variable temperature and loading is limited by excessively large deflections or by a material deterioration referred to as creep rupture. Basing on the Kachanov concept of damage, Leckie and Hayhurst suggested constitutive equations which reasonably represent the macroscopic behaviour of creeping material. This paper shows on the basis of these equations and the analysis of creep mechanisms the possibilities of a description of the creep behaviour of material under variable temperature and loading conditions. Also the influence of cyclic proportional loading and temperature gradient upon the rupture life and strains of a thick cylinder is investigated in detail. (Auth.)

  10. Collect Available Creep-Fatigue Data and Study Existing Creep-Fatigue Evaluation Procedures for Grade 91 and Hastelloy XR

    International Nuclear Information System (INIS)

    Asayama, Tai; Tachibana, Yukio

    2007-01-01

    This report describes the results of investigation on Task 5 of DOE/ASME Materials Project based on a contract between ASME Standards Technology, LLC (ASME ST-LLC) and Japan Atomic Energy Agency (JAEA). Task 5 is to collect available creep-fatigue data and study existing creep-fatigue evaluation procedures for Grade 91 steel and Hastelloy XR. Part I of this report is devoted to Grade 91 steel. Existing creep-fatigue data were collected (Appendix A) and analyzed from the viewpoints of establishing a creep-fatigue procedure for VHTR design. A fair amount of creep-fatigue data has been obtained and creep-fatigue phenomena have been clarified to develop design standards mainly for fast breeder reactors. Following this, existing creep-fatigue procedures were studied and it was clarified that the creep-fatigue evaluation procedure of the ASME-NH has a lot of conservatisms and they were analyzed in detail from the viewpoints of the evaluation of creep damage of material. Based on the above studies, suggestions to improve the ASME-NH procedure along with necessary research and development items were presented. Part II of this report is devoted to Hastelloy XR. Existing creep-fatigue data used for development of the high temperature structural design guideline for High Temperature Gas-cooled Reactor (HTGR) were collected. Creep-fatigue evaluation procedure in the design guideline and its application to design of the intermediate heat exchanger (IHX) for High Temperature Engineering Test Reactor (HTTR) was described. Finally, some necessary research and development items in relation to creep-fatigue evaluation for Gen IV and VHTR reactors were presented.

  11. Collect Available Creep-Fatigue Data and Study Existing Creep-Fatigue Evaluation Procedures for Grade 91 and Hastelloy XR

    Energy Technology Data Exchange (ETDEWEB)

    Tai Asayama; Yukio Tachibana

    2007-09-30

    This report describes the results of investigation on Task 5 of DOE/ASME Materials Project based on a contract between ASME Standards Technology, LLC (ASME ST-LLC) and Japan Atomic Energy Agency (JAEA). Task 5 is to collect available creep-fatigue data and study existing creep-fatigue evaluation procedures for Grade 91 steel and Hastelloy XR. Part I of this report is devoted to Grade 91 steel. Existing creep-fatigue data were collected (Appendix A) and analyzed from the viewpoints of establishing a creep-fatigue procedure for VHTR design. A fair amount of creep-fatigue data has been obtained and creep-fatigue phenomena have been clarified to develop design standards mainly for fast breeder reactors. Following this, existing creep-fatigue procedures were studied and it was clarified that the creep-fatigue evaluation procedure of the ASME-NH has a lot of conservatisms and they were analyzed in detail from the viewpoints of the evaluation of creep damage of material. Based on the above studies, suggestions to improve the ASME-NH procedure along with necessary research and development items were presented. Part II of this report is devoted to Hastelloy XR. Existing creep-fatigue data used for development of the high temperature structural design guideline for High Temperature Gas-cooled Reactor (HTGR) were collected. Creep-fatigue evaluation procedure in the design guideline and its application to design of the intermediate heat exchanger (IHX) for High Temperature Engineering Test Reactor (HTTR) was described. Finally, some necessary research and development items in relation to creep-fatigue evaluation for Gen IV and VHTR reactors were presented.

  12. Creep life simulations of EB welded copper overpack

    International Nuclear Information System (INIS)

    Holmstroem, S.; Laukkanen, A.; Andersson, T.

    2013-12-01

    The long term life predictions of copper overpack (sealed by EB welding in Finland) have previously been based on stress estimations that vary over a wide range, typically between 40-100 MPa. These values are usually not based on structural calculation including the EB-weld that increases the complexity of the stress state in the copper overpack. This report will attempt to pinpoint and simulate the stresses and strains developing in the copper overpack during its first decennia of repository service by advanced FEA simulations including the impact of the EB-weld. The main challenge of this work is the extrapolation of the creep strain response of OFP copper to the service relevant loads and temperatures. The uniaxial creep model is translated to a multiaxial constitutive equation form with adequate computational efficiency. The copper overpack strain and stress evolution has been simulated at up to 100 000 years at a conservative constant temperature of 80 deg C with 14 MPa of external pressure. The results indicate rapid creep relaxation in the initial stages after the load has been applied followed by limited creep strain accumulation thereafter. Local elastic-plastic and creep deformation is predicted at the EB weld root with a total strain of below 12 %. The predicted stresses after external loading and short term relaxation are moderate and the impact of weld residual stresses and the lower creep rupture properties of the EB seem not to be detrimental to the predicted long term creep response. The simulation results imply that the most crucial impact on the creep strain accumulation of the copper overpack is related to the OFP copper primary creep properties. The present study predicts sufficiently low creep strains for a 100 000 years canister life with the conservative assumption at a constant temperature of 80 deg C. However a sensitivity study on the impact of primary creep is strongly recommended due to contradicting analysis results from earlier FEA

  13. Creep of trabecular bone from the human proximal tibia

    Energy Technology Data Exchange (ETDEWEB)

    Novitskaya, Ekaterina, E-mail: eevdokim@ucsd.edu [Mechanical and Aerospace Engineering, UC, San Diego, La Jolla, CA 92093 (United States); Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States); Zin, Carolyn [Materials Science and Engineering, Johns Hopkins University, Baltimore, MD 21218 (United States); Chang, Neil; Cory, Esther; Chen, Peter [Departments of Bioengineering and Orthopaedic Surgery, UC, San Diego, La Jolla, CA 92093 (United States); D’Lima, Darryl [Shiley Center for Orthopaedic Research and Education, Scripps Health, La Jolla, CA 92037 (United States); Sah, Robert L. [Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States); Departments of Bioengineering and Orthopaedic Surgery, UC, San Diego, La Jolla, CA 92093 (United States); McKittrick, Joanna [Mechanical and Aerospace Engineering, UC, San Diego, La Jolla, CA 92093 (United States); Materials Science and Engineering Program, UC, San Diego, La Jolla, CA 92093 (United States)

    2014-07-01

    Creep is the deformation that occurs under a prolonged, sustained load and can lead to permanent damage in bone. Creep in bone is a complex phenomenon and varies with type of loading and local mechanical properties. Human trabecular bone samples from proximal tibia were harvested from a 71-year old female cadaver with osteoporosis. The samples were initially subjected to one cycle load up to 1% strain to determine the creep load. Samples were then loaded in compression under a constant stress for 2 h and immediately unloaded. All tests were conducted with the specimens soaked in phosphate buffered saline with proteinase inhibitors at 37 °C. Steady state creep rate and final creep strain were estimated from mechanical testing and compared with published data. The steady state creep rate correlated well with values obtained from bovine tibial and human vertebral trabecular bone, and was higher for lower density samples. Tissue architecture was analyzed by micro-computed tomography (μCT) both before and after creep testing to assess creep deformation and damage accumulated. Quantitative morphometric analysis indicated that creep induced changes in trabecular separation and the structural model index. A main mode of deformation was bending of trabeculae. - Highlights: • Compressive creep tests of human trabecular bone across the tibia were performed. • The creep rate was found to be inversely proportional to the density of the samples. • μ-computed tomography before and after testing identified regions of deformation. • Bending of the trabeculae was found to be the main deformation mode.

  14. Non-linear tensile creep of polypropylene: time-strain superposition and creep prediction

    Czech Academy of Sciences Publication Activity Database

    Kolařík, Jan; Pegoretti, A.

    2006-01-01

    Roč. 47, č. 1 (2006), s. 346-356 ISSN 0032-3861 R&D Projects: GA ČR GA106/04/1051 Institutional research plan: CEZ:AV0Z40500505 Keywords : polypropylene * tensile creep * free volume Subject RIV: JI - Composite Materials Impact factor: 2.773, year: 2006

  15. Contribution on creep polygonization study in crystals. Creep of single crystalline silver chloride and sodium chloride

    International Nuclear Information System (INIS)

    Pontikis, Vassilis

    1977-01-01

    Subgrain formation and their influence on plastic behavior of materials has been studied in the case of single crystals of silver chloride and sodium chloride crept at high temperature (T > 0.5 T melting ). It is shown that the creep rate ε is a function of the mean subgrain diameter d. For secondary creep ε ∝ d k with k = 2 for NaCl and AgCl. During secondary creep, the substructure changes continuously: sub-boundaries migrate and sub-grains rotate. We find that sub-boundaries migration accounts for 35 pc of the total strain and that subgrain misorientation θ increases linearly with strain ε: θ ∝ 0.14 ε. The stability of permanent creep seems related to the power that the substructure is able to dissipate. The possible subgrain formation mechanisms are examined. It is shown that subgrain formation is closely related to the geometrical conditions of deformation and to the heterogeneities of this later. (author) [fr

  16. Creep and Creep Crack Growth Behaviors for SMAW Weldments of Gr. 91 Steel

    International Nuclear Information System (INIS)

    Kim, Woo Gon; Yin, Song Nan; Park, Ji Yeon; Hong, Sung Deok; Kim, Yong Wan; Park, Jae Young

    2010-01-01

    High Cr ferritic resistance steels with tempered martensite microstructures posses enhanced creep strength at the elevated temperatures. Those steels as represented by a modified 9Cr-1Mo steel (ASME Grade 91, hereafter Gr.91) are regarded as main structural materials of sodium-cooled fast reactors (SFR) and reactor pressure vessel materials of very high temperature reactors (VHTR). The SFR and VHTR systems are designed during long-term duration reaching 60 years at elevated temperatures and often subjected to non-uniform stress and temperature distribution during service. These conditions may generate localized creep damage and propagate the cracks and ultimately may cause a fracture. A significant portion of its life is spent in crack propagation. Therefore, a creep crack growth rate (CCGR) due to creep damage should be assessed for both the base metal (BM) and welded metal (WM). Enough CCGR data for them should be provided for assessing their structural integrities. However, their CCGR data for the Gr. 91 steels is still insufficient. In this study, the CCGR for the BM and the WM of the Gr. 91 steel was comparatively investigated. A series of the CCG tests were conducted under different applied loads for the BM and the WM at 600 .deg. C. The CCGR was characterized in terms of the C parameter, and their CCG behavior were compared, respectively

  17. Correlation of creep rate with microstructural changes during high temperature creep

    Science.gov (United States)

    Young, C. T.; Sommers, B. R.; Lytton, J. L.

    1977-01-01

    Creep tests were conducted on Haynes 188 cobalt-base alloy and alpha titanium. The tests on Haynes 188 were conducted at 1600 F and 1800 F for stresses from 3 to 20 ksi, and the as-received, mill-annealed results were compared to specimens given 5%, 10%, and 15% room temperature prestrains and then annealed one hour at 1800 F. The tests on alpha titanium were performed at 7,250 and 10,000 psi at 500 C. One creep test was done at 527 C and 10,000 psi to provide information on kinetics. Results for annealed titanium were compared to specimens given 10% and 20% room temperature prestrains followed by 100 hours recovery at 550 C. Electron microscopy was used to relate dislocation and precipitate structure to the creep behavior of the two materials. The results on Haynes 188 alloy reveal that the time to reach 0.5% creep strain at 1600 F increases with increasing prestrain for exposure times less than 1,000 hours, the increase at 15% prestrain being more than a factor of ten.

  18. Creep, fatigue and creep-fatigue interactions in modified 9% Chromium - 1% Molybdenum (P91) steels

    Science.gov (United States)

    Kalyanasundaram, Valliappa

    Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the proposed research are to characterize the creep, fatigue and C-F behavior of grade P91 steels at 625 C and develop robust constitutive models for simulating/predicting their microstructural response under different loading conditions. This work will utilize experimental data from 16 laboratories worldwide that conducted tests (creep, fatigue and C-F) on grade P91 steel at 625°C in a round-robin (RR) program. Along with 7 creep deformation and rupture tests, 32 pure fatigue and 46 C-F tests from the RR are considered in this work. A phenomenological constitutive model formulated in this work needs just five fitting parameters to simulate/predict the monotonic, pure fatigue and C-F behavior of grade P91 at 625 C. A modified version of an existing constitutive model is also presented for particularly simulating its isothermal creep deformation and rupture behavior. Experimental results indicate that specimen C-F lives, as measured by the 2% load drop criterion, seem to decrease with increasing strain ranges and increasing hold times at 625°C. Metallographic assessment of the tested specimens shows that the damage mode in both pure fatigue and 600 seconds hold time cyclic tests is predominantly transgranular fatigue with some presence of

  19. Jojoba could stop the desert creep

    Energy Technology Data Exchange (ETDEWEB)

    1982-03-25

    The Sahara desert is estimated to be expanding at a rate of 5km a year. The Sudanese government is experimenting with jojoba in six different regions as the bush has the potential to stop this ''desert creep''. The plant, a native to Mexico, is long known for its resistance to drought and for the versatile liquid wax that can be extracted from its seeds. It is estimated that one hectare of mature plants could produce 3000 kg of oil, currently selling at $50 per litre, and so earn valuable foreign currency.

  20. Precise tensile creep measurement with refractory ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Rendtel, A. [GKSS-Forschungszentrum Geesthacht GmbH (Germany). Inst. fuer Werkstofforschung; Huebner, H. [Technische Univ. Hamburg-Harburg, Hamburg (Germany). Arbeitsbereich Werkstoffphysik und -technologie

    2001-08-01

    A recently established facility for tensile creep testing of ceramics at temperatures up to 1600 C in air is described. Displacement measurement is performed by flag-based scanning laser extensometry. A narrow and shielded laser path design and improvements in the furnace insulation were used to obtain a scatter of the displacement measurement of only {+-} 0,2 {mu}m, which is comparable to that obtained at room temperature. This stability of the displacement measurement was demonstrated with a hot-pressed (HP) silicon nitride containing 8 mass% Y{sub 2}O{sub 3} as sintering additive tested at 1500 C. (orig.)

  1. Changes in creep of polymethylmetacrylate after irradiation

    International Nuclear Information System (INIS)

    Peschanskaya, N.N.; Smolyanskij, A.S.; Suvorova, V.Yu.

    1992-01-01

    A study was made on PMMA, irradiated by different doses of 60 Co γ-radiation in vacuum under creep during compression. It is shown that occurence of tendency to failure at +20 degC is observed at doses of D > 100 kGy (> 10 Mrad), whereas sufficient decrease of deformation before failure takes place at D > 350 kGy. Peculiarities of behaviour of irradiated and nonirradiated PMMA under compression and tension were correlated. It is noted that critical irradiation doses may differ sufficiently for different loading conditions, deformation and longevity characteristics

  2. Power series like relation of power law and coupled creep ...

    African Journals Online (AJOL)

    When a solid deforms at high temperature its microstructure may in some sense be altered- holes and cracks may nucleate and grow inside the solid by various mechanism controlled by diffusion and by power law creep or by a combination of these mechanisms. Considering a coupled diffusion power law creep mechanism ...

  3. Creep threshold of a Mg-4Al-1Ca alloy

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel

    2008-01-01

    Roč. 46, č. 6 (2008), s. 323-329 ISSN 0023-432X R&D Projects: GA ČR GA106/06/1354 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * creep * threshold behaviour * threshold stress concept * mechanisms of creep Subject RIV: JG - Metallurgy Impact factor: 1.345, year: 2007

  4. Some numerical approaches of creep, thermal shock, damage and ...

    Indian Academy of Sciences (India)

    Some numerical approaches of creep, thermal shock, damage and delayed failure of ceramics and refractories ... Ceramic; refractories; creep; thermal stock; damage; delayed failure; numerical simulation. Abstract. Numerical simulation is now very often used to predict the behaviour of components in service conditions.

  5. Irradiation creep performance of graphite relevant for pebble bed HTRs

    International Nuclear Information System (INIS)

    Kleist, G.; O'Connor, M.F.

    1980-01-01

    Irradiation - induced creep in the core reflector component graphite of high temperature reactors is of primary importance to the core designer since it provides a mechanism for the relief of internal stresses arising from differential Wigner shrinkage and thermal expansion. The experimental determination of the extent of this creep for conditions relevant to the reactor is thus imperative

  6. Analysis of stress and deformation in non-stationary creep

    International Nuclear Information System (INIS)

    Feijoo, R.A.; Taroco, E.; Guerreiro, J.N.C.

    1980-12-01

    A variational method and its algorithm are presented; they permit the analysis of stress and deformation in non-stationary creep. This algorithm is applied to an infinite cylinder submitted to an internal pressure. The solution obtained is compared with the solution of non-stationary creep problems [pt

  7. Correct Interpretation of Creep Rates: A Case Study of Cu

    Czech Academy of Sciences Publication Activity Database

    Blum, W.; Dvořák, Jiří; Král, Petr; Eisenlohr, P.; Sklenička, V.

    2015-01-01

    Roč. 31, č. 11 (2015), s. 1065-1068 ISSN 1005-0302 R&D Projects: GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : Cu * Creep * Minimum creep rate * Activation energy * Stress exponent Subject RIV: JJ - Other Materials Impact factor: 2.267, year: 2015

  8. Creep mechanisms and constitutive relations in pure metals

    International Nuclear Information System (INIS)

    Nix, W.D.

    1979-01-01

    The mechanisms of creep of pure metals is briefly reviewed and divided into two parts: steady state flow mechanisms, and non-steady state flow mechanisms and constitutive relations. Creep by diffusional flow is now reasonably well understood, with theory and experiment in good agreement. The closely related phenomenon of Harper--Dorn creep can also be understood in terms of diffusion between dislocations. Power law creep involves the climb of edge disloctions controlled by lattice self diffusion. Theoretical treatments of this process invariably give a power law exponent of 3. This natural creep law is compared with the data for FCC and BCC metals. It is suggested that diffusion controlled climb is the controlling process in BCC metals at very high temperatures. Stacking fault energy effects may preclude the possibility that creep is controlled entirely by lattice self diffusion in some FCC metals. The subject of power law breakdown is presented as a natural consequence of the transition to low temperature flow phenomena. The role of core diffusion in this transition is briefly discussed. The mechanisms are presented by which pure metals creep at elevated temperatures. While most of this review deals with the mechanisms of steady state flow, some discussion is devoted to creep flow under non-steady state conditions. This topic is discussed in connection with the development of constitutive equations for describing plastic flow in metals

  9. Thermal activated grain boundary creep in polycrystalline copper ...

    African Journals Online (AJOL)

    Creep deformation in metals and alloys at intermediate temperatures and low stresses are attributed to power-law and diffusion mechanisms. Thermal activation parameters of steady state creep correlate with the macroscopic and microscopic variables, leading to inter-relationships between the apparent and true ...

  10. Irradiation creep experiments on fusion reactor candidate structural materials

    International Nuclear Information System (INIS)

    Hausen, H.; Cundy, M.R.; Schuele, W.

    1991-01-01

    Irradiation creep rates were determined for annealed and cold-worked AMCR- and 316-type steel alloys in the high flux reactor at Petten, for various irradiation temperatures, stresses and for neutron doses up to 4 dpa. Primary creep elongations were found in all annealed materials. A negative creep elongation was found in cold-worked materials for stresses equal to or below about 100 MPa. An increase of the negative creep elongation is found for decreasing irradiation temperatures and decreasing applied stresses. The stress exponent of the irradiation creep rate in annealed and cold-worked AMCR alloys is n = 1.85 and n = 1.1, respectively. The creep rates of cold-worked AMCR alloys are almost temperature independent over the range investigated (573-693 K). The results obtained in the HFR at Petten are compared with those obtained in ORR and EBR II. The smallest creep rates are found for cold-worked materials of AMCR- and US-PCA-type at Petten which are about a factor two smaller than the creep rates obtained of US-316 at Petten or for US-PCA at ORR or for 316L at EBR II. The scatter band factor for US-PCA, 316L, US-316 irradiated in ORR and EBR II is about 1.5 after a temperature and damage rate normalization

  11. Creep strength and ductility of 9 to 12% chromium steels

    DEFF Research Database (Denmark)

    Hald, John

    2004-01-01

    The present paper focuses in on long-term creep properties of parent material of the new 9-12%Cr creep resistant steels, P91, E911 and P92 developed for use in advanced ultrasupercritical power plants. These steels have been at the center of activities in the ECCC Working Group 3A (WG3A) "Ferriti...

  12. Physical hydrodynamic propulsion model study on creeping viscous ...

    Indian Academy of Sciences (India)

    2017-02-16

    Feb 16, 2017 ... Abstract. The present investigation focusses on a mathematical study of creeping viscous flow induced by metachronal wave propagation in a horizontal ciliated tube containing porous media. Creeping flow limitations are imposed, i.e. inertial forces are small compared to viscous forces and therefore a very ...

  13. secondary creep response of hand lay-up grp composites

    African Journals Online (AJOL)

    Dr Obe

    Other factors affecting the composite strength, creep response and fracture and delamination resistance revolve ... Glass/Carbon composite over a range of stress levels and recommended a parameter for creep ... Resistance Heating Chamber, operating with an Electrical Temperature Regulator, a strain. Guage, a Load ...

  14. The role of cobalt on the creep of Waspaloy

    Science.gov (United States)

    Jarrett, R. N.; Chin, L.; Tien, J. K.

    1984-01-01

    Cobalt was systematically replaced with nickel in Waspaloy (which normally contains 13% Co) to determine the effects of cobalt on the creep behavior of this alloy. Effects of cobalt were found to be minimal on tensile strengths and microstructure. The creep resistance and the stress rupture resistance determined in the range from 704 to 760 C (1300 to 1400 C) were found to decrease as cobalt was removed from the standard alloy at all stresses and temperatures. Roughly a ten-fold drop in rupture life and a corresponding increase in minimum creep rate were found under all test conditions. Both the apparent creep activation energy and the matrix contribution to creep resistance were found to increase with cobalt. These creep effects are attributed to cobalt lowering the stacking fault energy of the alloy matrix. The creep resistance loss due to the removal of cobalt is shown to be restored by slightly increasing the gamma' volume fraction. Results are compared to a previous study on Udimet 700, a higher strength, higher gamma' volume fraction alloy with similar phase chemistry, in which cobalt did not affect creep resistance. An explanation for this difference in behavior based on interparticle spacing and cross-slip is presented.

  15. Studies on the creep ratcheting behaviour of tube specimens

    International Nuclear Information System (INIS)

    Zottmaier, R.; Over, H.H.; Schubert, F.; Nickel, H.

    1985-09-01

    By superimposing cyclic secondary stresses sigmasub(T) additionally to a constant primary stress sigmasub(p), significant enhanced creep rates of structural components at very high temperatures may be the result. This effect is known as 'Creep Ratcheting' or 'Incremental Growth'. It may occur due to cyclic variations of thermal stresses in the walls of heat exchanger - or chemical reformer-tubes for example. The creep ratcheting effect was evaluated experimentally by comparing the creep behaviour of metallic tube specimens under constant axial load P with and without superimposed cyclic thermal stresses across the tube wall. For theoretical analysis a numerical computer programme has been developed. The tests on lead specimens at temperatures of up to 100 0 C and on the high temperature alloy X10 NiCrAlTi 32 20 H of up to 950 0 C showed no significant enhanced stationary creep rates for the stress relations sigmasub(T)/sigmasub(p) 2) the creep rate increased up to a factor of 15 compared to the creep behavior with the same primary stress as the only effective load. The results of the numerical computer programme developed for this paper and of a Finite Element Analysis showed good consistency with the experimental data only when the temperature dependence of the stationary creep rate and the shape of the time-temperature cycles of the thermal load variations were considered. (orig.) [de

  16. Creep-fatigue damage assessment by subsequent fatigue straining

    International Nuclear Information System (INIS)

    Yaguchi, Masatsugu; Nakamura, Toshiya; Ishikawa, Akiyoshi; Asada, Yasuhide

    1993-01-01

    A series of creep-fatigue tests has been conducted with Modified 9Cr-1Mo steel at 600 C in a high vacuum environment of 0.1 mPa to assess an accumulation of creep-fatigue damage. In these tests, each test specimen has been subjected to prior creep-fatigue loading followed by subsequent fatigue loading or prior fatigue loading followed by subsequent creep-fatigue loading. A linear summation of cumulative damage of fatigue and creep life fraction was smaller than unity for the former case, and larger than unity for the latter case. Scanning electron microscopic observation showed that in the case of prior creep-fatigue loading, a crack propagated from inclusions around which cavities were observed and its appearance transformed from transgranular to intergranular type with the increase of the number of cycles of prior creep-fatigue loading, while crack mode was predominantly intergranular in the case of prior fatigue loading. It was suggested that in the case of prior creep-fatigue loading, the fatigue life becomes shorter than that predicted by the linear rule due to early initiation of a crack caused from the cavity creation. In the case of prior fatigue loading, the crack propagates different courses in each loading to lead to the life fraction which is larger than unity

  17. New results in the limit analysis by secondary modified creep

    International Nuclear Information System (INIS)

    Feijoo, R.A.; Taroco, E.; Zouain, N.

    1982-03-01

    Two methods for computing upper and lower bounds of colapse loads are proposed by means of generalized creep constitutive relations. The actual material behaviour is rigid-perfectly plastic and the techniques here analized consist in the substitution of this material by a fictitious one which presents steady state creep response. Some analytical examples are also presented. (Author) [pt

  18. 98 Etude Comparative du Systeme Phonematique et Tonal des ...

    African Journals Online (AJOL)

    98. Etude Comparative du Systeme Phonematique et Tonal des. Deux Parlers: Le Yoruba du Nigeria et L'itsa Parle en. Republique du Benin. Ajani Akinwumi Lateef et Ayuba G. Ajibabi http://dx.doi./org/10.4314/ujah.v18i3.5. Résume. En ce début de l'époque ou la mondialisation et la coexistence des peuples dans le ...

  19. Determination of the Creep Parameters of Linear Viscoelastic Materials

    Directory of Open Access Journals (Sweden)

    Alibay Iskakbayev

    2016-01-01

    Full Text Available Creep process of linear viscoelastic materials is described by the integral equation of Boltzmann-Volterra in which creep kernel is approximated by Rabotnov’s fractional exponential function. The creep equation contains four unknown parameters: α, singularity parameter; β, fading parameter; λ, rheological parameter; and ε0, conditionally instantaneous strain. Two-stage determination method of creep parameters is offered. At the first stage, taking into account weak singularity properties of Abel’s function at the initial moment of loading, parameters ε0 and α are determined. At the second stage, using already known parameters ε0 and α, parameters β and λ are determined. Analytical expressions for calculating these parameters are obtained. An accuracy evaluation of the offered method with using experimentally determined creep strains of material Nylon 6 and asphalt concrete showed its high accuracy.

  20. Irradiation creep induced anisotropy in a/2 dislocation populations

    International Nuclear Information System (INIS)

    Gelles, D.S.

    1984-05-01

    The contribution of anisotropy in Burgers vector distribution to irradiation creep behavior has been largely ignored in irradiation creep models. However, findings on Frank loops suggest that it may be very important. Procedures are defined to identify the orientations of a/2 Burgers vectors for dislocations in face-centered cubic crystals. By means of these procedures the anisotropy in Burgers vector populations was determined for three Nimonic PE16 pressurized tube specimens irradiated under stress. Considerable anisotropy in Burgers vector population develops during irradiation creep. It is inferred that dislocation motion during irradiation creep is restricted primarily to a climb of a/2 dislocations on 100 planes. Effect of these results on irradiation creep modeling and deformation induced irradiation growth is considered

  1. Application Of Shakedown Analysis To Cyclic Creep Damage Limits

    Energy Technology Data Exchange (ETDEWEB)

    Carter, Peter [Stress Engineering Services Inc.; Jetter, Robert I [Consultant; Sham, Sam [ORNL

    2012-01-01

    Shakedown analysis may be used to provide a conservative estimate of local rupture and hence cyclic creep damage for use in a creep-fatigue assessment. The shakedown analysis is based on an elastic-perfectly plastic material with a temperature-dependent pseudo yield stress defined to guarantee that a shakedown solution exists which does not exceed rupture stress and temperature for a defined life. The ratio of design life to the estimated maximum cyclic life is the shakedown creep damage. The methodology does not require stress classification and is also applicable to cycles over the full range of temperature above and below the creep regime. Full cyclic creep and damage analysis is the alternative when shakedown analysis appears to be excessively conservative.

  2. Creep damage development in welded X20 and P91

    Energy Technology Data Exchange (ETDEWEB)

    Brett, Steve; Holmstrom, Stefan; Hald, John; Borg, Ulrik; Aakjaer Jensen, Soeren; Vulpen, Rijk Van; Degnan, Craig; Vinter Dahl, Kristian; Vilhelmsen, Tommy

    2011-03-15

    The Martensitic steel X20CrMoV121 (hereinafter called X20) and the modified 9Cr1Mo steel (hereinafter called P91) have been used for a number of years in high temperature applications since they posses superior creep strength compared to low alloyed steels. Due to the simple fact that very few failures were observed, almost no knowledge as to the evolution of creep damage in welds were available despite long operation times exceeding well over 100.000 hours. It has been suggested that X20 will develop creep damage in a different manner compared to low alloyed steel, i.e damage initiation should be slow followed by accelerated growth. The research work presented in this report included systematic investigations of the first components of X20, which has developed creep during long-term operation. All of the investigated components showed creep damage evolution similar to low alloy steels

  3. The creep behavior of In-Ag eutectic solder joints

    International Nuclear Information System (INIS)

    Reynolds, H.L.; Kang, S.H.; Morris, J.W. Jr.; Univ. of California, Berkeley, CA

    1999-01-01

    The addition of 3 wt.% Ag to In results in a eutectic composition with improved mechanical properties while only slightly lowering the melting temperature. Steady-state creep properties of In-Ag eutectic solder joints have been measured using constant load tests at 0, 30, 60, and 90 C. Constitutive equations are derived to describe the creep behavior. The data are well represented by an equation of the form proposed by Dorn: a power-law equation applies to each independent creep mechanism. Two parallel mechanisms were observed for the In-Ag eutectic joints. The high-stress mechanism is a bulk mechanism with a thermal dependence dominated by the thermal dependence of creep in the In-rich matrix. The low-stress mechanism is a grain boundary mechanism. Results of this work are discussed with regard to creep behavior of typical eutectic systems

  4. Tensile and Creep Testing of Sanicro 25 Using Miniature Specimens

    Science.gov (United States)

    Dymáček, Petr; Jarý, Milan; Dobeš, Ferdinand; Kloc, Luboš

    2018-01-01

    Tensile and creep properties of new austenitic steel Sanicro 25 at room temperature and operating temperature 700 °C were investigated by testing on miniature specimens. The results were correlated with testing on conventional specimens. Very good agreement of results was obtained, namely in yield and ultimate strength, as well as short-term creep properties. Although the creep rupture time was found to be systematically shorter and creep ductility lower in the miniature test, the minimum creep rates were comparable. The analysis of the fracture surfaces revealed similar ductile fracture morphology for both specimen geometries. One exception was found in a small area near the miniature specimen edge that was cut by electro discharge machining, where an influence of the steel fracture behavior at elevated temperature was identified. PMID:29337867

  5. Tensile and Creep Testing of Sanicro 25 Using Miniature Specimens.

    Science.gov (United States)

    Dymáček, Petr; Jarý, Milan; Dobeš, Ferdinand; Kloc, Luboš

    2018-01-16

    Tensile and creep properties of new austenitic steel Sanicro 25 at room temperature and operating temperature 700 °C were investigated by testing on miniature specimens. The results were correlated with testing on conventional specimens. Very good agreement of results was obtained, namely in yield and ultimate strength, as well as short-term creep properties. Although the creep rupture time was found to be systematically shorter and creep ductility lower in the miniature test, the minimum creep rates were comparable. The analysis of the fracture surfaces revealed similar ductile fracture morphology for both specimen geometries. One exception was found in a small area near the miniature specimen edge that was cut by electro discharge machining, where an influence of the steel fracture behavior at elevated temperature was identified.

  6. Tensile and Creep Testing of Sanicro 25 Using Miniature Specimens

    Directory of Open Access Journals (Sweden)

    Petr Dymáček

    2018-01-01

    Full Text Available Tensile and creep properties of new austenitic steel Sanicro 25 at room temperature and operating temperature 700 °C were investigated by testing on miniature specimens. The results were correlated with testing on conventional specimens. Very good agreement of results was obtained, namely in yield and ultimate strength, as well as short-term creep properties. Although the creep rupture time was found to be systematically shorter and creep ductility lower in the miniature test, the minimum creep rates were comparable. The analysis of the fracture surfaces revealed similar ductile fracture morphology for both specimen geometries. One exception was found in a small area near the miniature specimen edge that was cut by electro discharge machining, where an influence of the steel fracture behavior at elevated temperature was identified.

  7. Creep closure of an opening in a deep potash mine

    International Nuclear Information System (INIS)

    Montgomery, S.T.

    1983-01-01

    The creep closure of an isolated opening in a deep potash mine at Esterhazy, Canada, has been simulated with finite element calculations. These were done to assess the plausibility of a creep model, developed from laboratory data, for natural rock salt. Since it is difficult to generate and interpret creep data at the low stresses likely to be encountered around underground excavations, the comparison of field measurements with model predictions is valuable in establishing the plausibility of constitutive models for creep over a long time at low stresses. The favorable comparison obtained in this study, between predicted wall convergences, and those measured over a period of eight years in the opening at Esterhazy, helps verify the creep model used. 2 figures

  8. Creep behavior of a nanocrystalline Fe-B-Si alloy

    International Nuclear Information System (INIS)

    Xiao, M.; Kong, Q.P.

    1997-01-01

    The research of nanocrystalline materials has attracted much attention in the world. In recent years, there have been several studies on their creep behavior. Among these, the authors have studied the tensile creep of a nanocrystalline Ni-P alloy (28 nm) at temperatures around 0.5 Tm (Tm is the melting point). The samples were prepared by the method of crystallization of amorphous ribbon. Based on the data of stress exponent and activation energy, they suggested that the creep was controlled by boundary diffusion; while the creep of the same alloy with a larger grain size (257 nm) was controlled by a different mechanism. In the present paper, the authors extend the research to the creep of a nanocrystalline Fe-B-Si alloy. The samples are also prepared by crystallization of amorphous ribbon. The samples such prepared have an advantage that the interfaces are naturally formed without artificial compaction and porosity

  9. Experimental Research on Creep Characteristics of Nansha Soft Soil

    Directory of Open Access Journals (Sweden)

    Qingzi Luo

    2014-01-01

    Full Text Available A series of tests were performed to investigate the creep characteristics of soil in interactive marine and terrestrial deposit of Pearl River Delta. The secondary consolidation test results show that the influence of consolidation pressure on coefficient of secondary consolidation is conditional, which is decided by the consolidation state. The ratio of coefficient of secondary consolidation and coefficient of compressibility Ca/Cc is almost a constant, and the value is 0.03. In the shear-box test, the direct sheer creep failure of soil is mainly controlled by shear stress rather than the accumulation of shear strain. The triaxial creep features are closely associated with the drainage conditions, and consolidation can weaken the effect of creep. When the soft soil has triaxial creep damage, the strain rate will increase sharply.

  10. Creep Behavior and Durability of Cracked CMC

    Science.gov (United States)

    Bhatt, R. T.; Fox, Dennis; Smith, Craig

    2015-01-01

    To understand failure mechanisms and durability of cracked Ceramic matrix composites (CMCs), Melt Infiltration (MI) SiCSiC composites with Sylramic-iBN fibers and full Chemical vapour infiltration SiCSiC composites with Sylramic-ion bombarded BN (iBN) and Hi-Nicalon -S fibers were pre-cracked between 150 to 200 megapascal and then creep and Sustained Peak Low Cycle Fatigue (SPLCF) tested at 13150 C at stress levels from 35 to 103 megapascal for up to 200 hours under furnace and burner rig conditions. In addition creep testing was also conducted on pre-cracked full Chemical vapour infiltration SiCSiC composites at 14500 C between 35 and 103 megapascal for up to 200 hours under furnace conditions. If the specimens survived the 200 hour durability tests, then they were tensile tested at room temperature to determine their residual tensile properties. The failed specimens were examined by Scanning electron microscope (SEM) to determine the failure modes and mechanisms. The influence of crack healing matrix, fiber types, crack density, testing modes and interface oxidation on durability of cracked Ceramic matrix composites (CMCs) will be discussed.

  11. Paths of interactive cracks in creep conditions

    Directory of Open Access Journals (Sweden)

    K. Nowak

    2015-10-01

    Full Text Available The paper contains plane strain analysis of uniformly stretched plate working in creep condition. The plate contains initial defects in forms of central and/or edge cracks working in mode I. These cracks are modelled by attributing critical value of damage parameter to preset points and therefore resulting in stresses set to zero (material does not support any loading. The Continuum Damage Mechanics constitutive equations are used to describe the creep crack growth problem and Finite Element Method Abaqus system is applied to solve corresponding boundary and initial value problem. Analysis of different initial cracks configuration has been performed. The crack path is defined by points in which damage parameter equals to critical one. Time to failure of the plate with single initial crack is achieved when the crack path spans its width. This time is calculated and compared to the time to failure of initially uncracked structure. For the plate with multiple cracks the paths starting from different cracks can develop independently until they merge and/or span the plate width. In each case the damage field is analysed and the direction of crack path development is determined. The analysis of crack propagation allows for determination of a distance between initial cracks for which the interaction between them is negligible. It is demonstrated that Continuum Damage Mechanics approach allows not only to model the development of initially existing cracks but also initiation of new, cross-spanning cracks and their kinking and branching.

  12. Acoustic signal analysis in the creeping discharge

    International Nuclear Information System (INIS)

    Nakamiya, T; Sonoda, Y; Tsuda, R; Ebihara, K; Ikegami, T

    2008-01-01

    We have previously succeeded in measuring the acoustic signal due to the dielectric barrier discharge and discriminating the dominant frequency components of the acoustic signal. The dominant frequency components appear over 20kHz of acoustic signal by the dielectric barrier discharge. Recently surface discharge control technology has been focused from practical applications such as ozonizer, NO X reactors, light source or display. The fundamental experiments are carried to examine the creeping discharge using the acoustic signal. When the high voltage (6kV, f = 10kHz) is applied to the electrode, the discharge current flows and the acoustic sound is generated. The current, voltage waveforms of creeping discharge and the sound signal detected by the condenser microphone are stored in the digital memory scope. In this scheme, Continuous Wavelet Transform (CWT) is applied to discriminate the acoustic sound of the micro discharge and the dominant frequency components are studied. CWT results of sound signal show the frequency spectrum of wideband up to 100kHz. In addition, the energy distributions of acoustic signal are examined by CWT

  13. [Creep of amalgam fillings under clasp rests].

    Science.gov (United States)

    Borchers, L; Jung, T; West, M

    1989-10-01

    A clinically realistic experiment was set up to obtain information on the amount of vertical settling of clasp rests in amalgam restorations under functional loading. Mesioocclusal cavities were prepared in 16 lower molar specimens cast in brass. The cavities were filled with amalgam and provided with a mesial rest seat. A constant load of 100 N was applied via a simplified (experimental) saddle to a cobalt-chromium E-clasp cast to the saddle. The duration of the load corresponded to 160 days of clinical function. The chronological course of vertical displacement was analyzed mathematically. According to this result the process can be divided into three components: settling immediately upon load initiation (mean value 96 microns, transition creep (mean value 25 microns) and creep ata constant rate (mean value 15 microns). The mean overall vertical displacement of the rests was 136 microns, the maximum value 287 microns. These findings suggest that vertical settling of a clasp rest into its seat in an amalgam restoration may eventually result in significant changes in occlusion and may almost completely exhaust gingival resilience.

  14. Tension-Compression Asymmetry of Creep and Unilateral Creep Damage in Aluminum for Isothermal and Nonisothermal Processes

    Science.gov (United States)

    Zolochevsky, Alexander; Obataya, Yoichi

    A constitutive model is proposed to describe the damage development in aluminum alloys under creep conditions for both isothermal and nonisothermal processes. Special emphasis is laid on four specific phenomena: tension-compression asymmetry of creep, damage induced anisotropy, unilateral creep damage and damage deactivation. Within the framework of the phenomenological approach in the Continuum Damage Mechanics, the nonlinear tensor constitutive equation for creep deformation and damage evolution equation are proposed to account for different orientation of microcracks in aluminum alloys under tensile and compressive loading types. After a determination of the material parameters in the obtained constitutive equation and damage growth equation, the proposed model is applied to the describing creep behavior of the aluminum alloy under uniaxial nonproportional and multiaxial nonproportional loading for both isothermal and nonisothermal processes.

  15. Diffusion creep in the mantle may create and maintain anisotropy

    Science.gov (United States)

    Wheeler, John

    2014-05-01

    Diffusion creep is thought to play an important role in lower mantle deformation and hence must be understood in detail if Earth behaviour is to be explained. It is commonly claimed that diffusion creep gives rise to equant grain shapes and destroys any crystallographic preferred orientation (CPO), so all physical properties would be isotropic. Some experiments on olivine support the first assertion but other minerals, and polyphase rocks, commonly show inequant grain shapes in nature and experiment even when diffusion creep is thought to be a major contribution to strain. Numerical models allow rigorous exploration of the effects of deformation under conditions not easily reached in experiments. A numerical model named 'DiffForm' (Wheeler & Ford 2007) gives insight into how grain shapes and microstructures evolve during diffusion creep. Modelling shows that whilst grains may initially rotate in apparently chaotic fashion during diffusion creep, such rotations slow down as grains become inequant. Consequently, an initial CPO (formed, for example, by dislocation creep at higher strain rates) will be decreased in intensity but not destroyed. Seismic anisotropy will decrease but not disappear (Wheeler 2009). Diffusion creep is also predicted to have intense mechanical anisotropy. In simple models diffusion creep is controlled entirely by diffusion and sliding along grain boundaries; there is no crystallographic influence. An aggregate of equant grains must then be mechanically isotropic, but a model microstructure with inequant grains has marked mechanical anisotropy (Wheeler 2010) - an effect related to the fact that grain boundary sliding is an intrinsic part of diffusion creep. That work was based on a very simple microstructure with a single inequant grain shape but I present here new results showing that for more complicated microstructures, mechanical anisotropy is intense even for quite modest grain elongations. There will be feedback between strain and

  16. Carbon dioxide as chemical feedstock

    National Research Council Canada - National Science Library

    Aresta, M

    2010-01-01

    ... Dioxide as an Inert Solvent for Chemical Syntheses 15 Alessandro Galia and Giuseppe Filardo Introduction 15 Dense Carbon Dioxide as Solvent Medium for Chemical Processes 15 Enzymatic Catalysis in Dense Carbon Dioxide 18 Other Reactions in Dense Carbon Dioxide 19 Polymer Synthesis in Supercritical Carbon Dioxide 20 Chain Polymerizations: Synt...

  17. Creep and Creep-Fatigue Crack Growth at Structural Discontinuities and Welds

    Energy Technology Data Exchange (ETDEWEB)

    Dr. F. W. Brust; Dr. G. M. Wilkowski; Dr. P. Krishnaswamy; Mr. Keith Wichman

    2010-01-27

    The subsection ASME NH high temperature design procedure does not admit crack-like defects into the structural components. The US NRC identified the lack of treatment of crack growth within NH as a limitation of the code and thus this effort was undertaken. This effort is broken into two parts. Part 1, summarized here, involved examining all high temperature creep-fatigue crack growth codes being used today and from these, the task objective was to choose a methodology that is appropriate for possible implementation within NH. The second part of this task, which has just started, is to develop design rules for possible implementation within NH. This second part is a challenge since all codes require step-by-step analysis procedures to be undertaken in order to assess the crack growth and life of the component. Simple rules for design do not exist in any code at present. The codes examined in this effort included R5, RCC-MR (A16), BS 7910, API 579, and ATK (and some lesser known codes). There are several reasons that the capability for assessing cracks in high temperature nuclear components is desirable. These include: (1) Some components that are part of GEN IV reactors may have geometries that have sharp corners - which are essentially cracks. Design of these components within the traditional ASME NH procedure is quite challenging. It is natural to ensure adequate life design by modeling these features as cracks within a creep-fatigue crack growth procedure. (2) Workmanship flaws in welds sometimes occur and are accepted in some ASME code sections. It can be convenient to consider these as flaws when making a design life assessment. (3) Non-destructive Evaluation (NDE) and inspection methods after fabrication are limited in the size of the crack or flaw that can be detected. It is often convenient to perform a life assessment using a flaw of a size that represents the maximum size that can elude detection. (4) Flaws that are observed using in-service detection

  18. An axisymmetric method of creep analysis for primary and secondary creep

    International Nuclear Information System (INIS)

    Jahed, Hamid; Bidabadi, Jalal

    2003-01-01

    A general axisymmetric method for elastic-plastic analysis was previously proposed by Jahed and Dubey [ASME J Pressure Vessels Technol 119 (1997) 264]. In the present work the method is extended to the time domain. General rate type governing equations are derived and solved in terms of rate of change of displacement as a function of rate of change in loading. Different types of loading, such as internal and external pressure, centrifugal loading and temperature gradient, are considered. To derive specific equations and employ the proposed formulation, the problem of an inhomogeneous non-uniform rotating disc is worked out. Primary and secondary creep behaviour is predicted using the proposed method and results are compared to FEM results. The problem of creep in pressurized vessels is also solved. Several numerical examples show the effectiveness and robustness of the proposed method

  19. Analysis of Indentation-Derived Power-Law Creep Response

    Science.gov (United States)

    Martinez, Nicholas J.; Shen, Yu-Lin

    2016-03-01

    The use of instrumented indentation to characterize power-law creep is studied by computational modeling. Systematic finite element analyses were conducted to examine how indentation creep tests can be employed to retrieve the steady-state creep parameters pertaining to regular uniaxial loading. The constant indentation load hold and constant indentation-strain-rate methods were considered, first using tin (Sn)-based materials as a model system. The simulated indentation-strain rate-creep stress relations were compared against the uniaxial counterparts serving as model input. It was found that the constant indentation-strain-rate method can help establish steady-state creep, and leads to a more uniform behavior than the constant-load hold method. An expanded parametric analysis was then performed using the constant indentation-strain-rate method, taking into account a wide range of possible power-law creep parameters. The indentation technique was found to give rise to accurate stress exponents, and a certain trend for the ratio between indentation strain rate and uniaxial strain rate was identified. A contour-map representation of the findings serves as practical guidance for determining the uniaxial power-law creep response based on the indentation technique.

  20. Cyclic creep and anelastic relaxation analysis of an ODS superalloy

    Science.gov (United States)

    Nardone, Vincent C.; Kimmerle, William L.; Tien, John K.

    1986-09-01

    This paper documents the effect of stress and temperature on the cyclic minimum strain rate at two different loading frequencies for the oxide dispersion strengthened (ODS) superalloy, INCONEL* MA 6000. The apparent stress exponent and activation energy for cyclic creep at both frequencies studied are shown to be greater than values observed for static creep. The large values of the stress exponent and activation energy for cyclic creep are proposed to result from anelastic strain storage delaying nonrecoverable creep during the on-load portion of the cyclic creep loading, such that the “effective stress” driving nonrecoverable creep is only a small fraction of the applied stress. In addition, the temperature dependence of the anelastic relaxation that occurs during the off-load portion of the cyclic creep loading is determined. The activation energy found for the relaxation process is equal to about one-half that for self-diffusion in nickel. A mechanism of localized climb of dislocations over the oxide dispersoids present in INCONEL MA 6000 is postulated to account for the observed activation energy of the relaxation process.

  1. A discrete dislocation dynamics model of creeping single crystals

    Science.gov (United States)

    Rajaguru, M.; Keralavarma, S. M.

    2018-04-01

    Failure by creep is a design limiting issue for metallic materials used in several high temperature applications. Current theoretical models of creep are phenomenological with little connection to the underlying microscopic mechanisms. In this paper, a bottom-up simulation framework based on the discrete dislocation dynamics method is presented for dislocation creep aided by the diffusion of vacancies, known to be the rate controlling mechanism at high temperature and stress levels. The time evolution of the creep strain and the dislocation microstructure in a periodic unit cell of a nominally infinite single crystal is simulated using the kinetic Monte Carlo method, together with approximate constitutive laws formulated for the rates of thermal activation of dislocations over local pinning obstacles. The deformation of the crystal due to dislocation glide between individual thermal activation events is simulated using a standard dislocation dynamics algorithm, extended to account for constant stress periodic boundary conditions. Steady state creep conditions are obtained in the simulations with the predicted creep rates as a function of stress and temperature in good agreement with experimentally reported values. Arrhenius scaling of the creep rates as a function of temperature and power-law scaling with the applied stress are also reproduced, with the values of the power-law exponents in the high stress regime in good agreement with experiments.

  2. Prediction of Asphalt Creep Compliance Using Artificial Neural Networks

    Directory of Open Access Journals (Sweden)

    Zofka A.

    2012-06-01

    Full Text Available Creep compliance of the hot-mix asphalt (HMA is a primary input of the pavement thermal cracking prediction model in the recently developed Mechanistic-Empirical Pavement Design Guide (M-EPDG in the US. The HMA creep compliance is typically determined from the Indirect Tension (IDT tests and requires complex experimental setup. On the other hand, creep compliance of asphalt binders is determined from a relatively simple three- point bending test performed in the Bending Beam Rheometer (BBR device. This paper discusses a process of training an Artificial Neural Network (ANN to correlate the creep compliance values obtained from the IDT with those from an innovative approach of testing HMA beams in the BBR. In addition, ANNs are also trained to predict HMA creep compliance from the creep compliance of asphalt binder and vice versa using the BBR setup. All trained ANNs exhibited a very high correlation of 97 to 99 percent between predicted and measured values. The binder creep compliance curves built on the ANN-predicted values also exhibited good correlation with those obtained from laboratory experiments. However, the simulation of trained ANNs on the independent dataset produced a significant deviation from the expected values which was most likely caused by the differences in material composition, such as aggregate type and gradation, presence of recycled additives, and binder type.

  3. Recent Methodologies for Creep Deformation Analysis and Its Life Prediction

    International Nuclear Information System (INIS)

    Kim, Woo-Gon; Park, Jae-Young; Iung

    2016-01-01

    To design the high-temperature creeping materials, various creep data are needed for codification, as follows: i) stress vs. creep rupture time for base metals and weldments (average and minimum), ii) stress vs. time to 1% total strain (average), iii) stress vs. time to onset of tertiary creep (minimum), and iv) constitutive eqns. for conducting time- and temperature- dependent stress-strain (average), and v) isochronous stress-strain curves (average). Also, elevated temperature components such as those used in modern power generation plant are designed using allowable stress under creep conditions. The allowable stress is usually estimated on the basis of up to 10 5 h creep rupture strength at the operating temperature. The master curve of the “sinh” function was found to have a wider acceptance with good flexibility in the low stress ranges beyond the experimental data. The proposed multi-C method in the LM parameter revealed better life prediction than a single-C method. These improved methodologies can be utilized to accurately predict the long-term creep life or strength of Gen-IV nuclear materials which are designed for life span of 60 years

  4. Interface Evolution During Transient Pressure Solution Creep

    Science.gov (United States)

    Dysthe, D. K.; Podladchikov, Y. Y.; Renard, F.; Jamtveit, B.; Feder, J.

    When aggregates of small grains are pressed together in the presence of small amounts of solvent the aggregate compacts and the grains tend to stick together. This hap- pens to salt and sugar in humid air, and to sediments when buried in the Earths crust. Stress concentration at the grain contacts cause local dissolution, diffusion of the dissolved material out of the interface and deposition on the less stressed faces of the grains{1}. This process, in geology known as pressure solution, plays a cen- tral role during compaction of sedimentary basins{1,2}, during tectonic deformation of the Earth's crust{3}, and in strengthening of active fault gouges following earth- quakes{4,5}. Experimental data on pressure solution has so far not been sufficiently accurate to understand the transient processes at the grain scale. Here we present ex- perimental evidence that pressure solution creep does not establish a steady state inter- face microstructure as previously thought. Conversely, cumulative creep strain and the characteristic size of interface microstructures grow as the cubic root of time. A sim- ilar transient phenomenon is known in metallurgy (Andrade creep) and is explained here using an analogy with spinodal dewetting. 1 Weyl, P. K., Pressure solution and the force of crystallization - a phenomenological theory. J. Geophys. Res., 64, 2001-2025 (1959). 2 Heald, M. T., Cementation of Simpson and St. Peter Sandstones in parts of Okla- homa, Arkansas and Missouri, J. Geol. Chicago, 14, 16-30 (1956). 3 Schwartz, S., Stöckert, B., Pressure solution in siliciclastic HP-LT metamorphic rocks constraints on the state of stress in deep levels of accretionary complexes. Tectonophysics, 255, 203-209 (1996). 4 Renard, F., Gratier, J.P., Jamtveit, B., Kinetics of crack-sealing, intergranular pres- sure solution, and compaction around active faults. J. Struct. Geol., 22, 1395-1407, (2000). 5 Miller, S. A., BenZion, Y., Burg, J. P.,A three-dimensional fluid-controlled earth

  5. Creep-fatigue modelling in structural steels using empirical and constitutive creep methods implemented in a strip-yield model

    Science.gov (United States)

    Andrews, Benjamin J.

    The phenomena of creep and fatigue have each been thoroughly studied. More recently, attempts have been made to predict the damage evolution in engineering materials due to combined creep and fatigue loading, but these formulations have been strictly empirical and have not been used successfully outside of a narrow set of conditions. This work proposes a new creep-fatigue crack growth model based on constitutive creep equations (adjusted to experimental data) and Paris law fatigue crack growth. Predictions from this model are compared to experimental data in two steels: modified 9Cr-1Mo steel and AISI 316L stainless steel. Modified 9Cr-1Mo steel is a high-strength steel used in the construction of pressure vessels and piping for nuclear and conventional power plants, especially for high temperature applications. Creep-fatigue and pure creep experimental data from the literature are compared to model predictions, and they show good agreement. Material constants for the constitutive creep model are obtained for AISI 316L stainless steel, an alloy steel widely used for temperature and corrosion resistance for such components as exhaust manifolds, furnace parts, heat exchangers and jet engine parts. Model predictions are compared to pure creep experimental data, with satisfactory results. Assumptions and constraints inherent in the implementation of the present model are examined. They include: spatial discretization, similitude, plane stress constraint and linear elasticity. It is shown that the implementation of the present model had a non-trivial impact on the model solutions in 316L stainless steel, especially the spatial discretization. Based on these studies, the following conclusions are drawn: 1. The constitutive creep model consistently performs better than the Nikbin, Smith and Webster (NSW) model for predicting creep and creep-fatigue crack extension. 2. Given a database of uniaxial creep test data, a constitutive material model such as the one developed for

  6. Confirmation of Low Stress Creep Regime in 9% Chromium Steel by Stress Change Creep Experiments

    Czech Academy of Sciences Publication Activity Database

    Kloc, Luboš; Sklenička, Václav

    387-389, - (2004), s. 633-638 ISSN 0921-5093. [International Conference on the Strength of Materials /13./. Budapest, 25.08.2003-30.08.2003] R&D Projects: GA AV ČR IAA2041101; GA ČR GA106/02/0608 Institutional research plan: CEZ:AV0Z2041904 Keywords : Low stress creep * 9% Cr steel Subject RIV: JG - Metallurgy Impact factor: 1.445, year: 2004

  7. An Approach for Impression Creep of Lead Free Microelectronic Solders

    Science.gov (United States)

    Anastasio, Onofrio A.

    2002-06-01

    Currently, the microelectronics industry is transitioning from lead-containing to lead-free solders in response to legislation in the EU and Japan. Before an alternative alloy can be designated as a replacement for current Pb-Sn extensive testing must be accomplished. One major characteristic of the alloy that must be considered is creep. Traditionally, creep testing requires numerous samples and a long tin, which thwarts the generation of comprehensive creep databases for difficult to prepare samples such as microelectronic solder joints. However, a relatively new technique, impression creep enables us to rapidly generate creep data. This test uses a cylindrical punch with a flat end to make an impression on the surface of a specimen under constant load. The steady state velocity of the indenter is found to have the same stress and temperature dependence as the conventional unidirectional creep test using bulk specimens. This thesis examines impression creep tests of eutectic Sn-Ag. A testing program and apparatus was developed constructed based on a servo hydraulic test frame. The apparatus is capable of a load resolution of 0.01N with a stability of plus/minus 0.1N, and a displacement resolution of 0.05 microns with a stability of plus/minus 0.1 microns. Samples of eutectic Sn-Ag solder were reflowed to develop the microstructure used in microelectronic packaging. Creep tests were conducted at various stresses and temperatures and showed that coarse microstructures creep more rapidly than the microstructures in the tested regime.

  8. A review of irradiation induced creep in graphite under CAGR conditions

    International Nuclear Information System (INIS)

    Brocklehurst, J.E.; Kelly, B.T.

    1989-06-01

    Graphite irradiation induced creep data have been reviewed in detail and compared with the existing model used for stress calculations under Commercial Advanced Gas Cooled Reactor conditions. The relationship between creep and elastic modulus is well established and allows the creep behaviour of any graphite in any orientation to be predicted. The model predicts the initial build up of creep strain in different graphites extremely well. However, there are differences between prediction and experiment in creep at high doses; a creep test on a pre-irradiated specimen showed rather more creep ductility than predicted, whilst in experiments under a constant stress applied for the whole period of irradiation, the creep rates decreased to lower values than predicted. It is suggested that to obtain better estimates of brick stresses future irradiation experiments should aim to generate creep data under realistic variations in applied stress level, or rather creep strain history. (author)

  9. Creep relaxation of fuel pin bending and ovalling stresses

    International Nuclear Information System (INIS)

    Chan, D.P.; Jackson, R.J.

    1979-06-01

    Analytical methods for calculating fuel pin cladding bending and ovalling stresses due to pin bundle-duct mechanical interaction taking into account nonlinear creep are presented. Calculated results are in close agreement with finite element results by MARC-CDC program. The methods are used to investigate the effect of creep on the FTR fuel cladding bending and ovalling stresses. It is concluded that the cladding of 316 SS 20% CW and reference design has high creep rates in the FTR core region to keep the bending and ovalling stresses to low levels

  10. Creep transients in a nuclear-grade ODS ferritic steel

    Science.gov (United States)

    Evans, R. W.; Preston, J.; Wilshire, B.; Little, E. A.

    1992-10-01

    Inflexions are detected in the steady state creep regime of a nuclear-grade 13% Cr oxide-dispersion-strengthened ferritic alloy when tested at 700-725°C in an annealed condition. This anomalous response can be suppressed by using a two-stage annealing plus ageing heat treatment designed to fully precipitate a stable chi-phase intermetallic. Mechanisms directly related to observed creep-induced precipitation of chi-phase cannot account for the creep transients, but a tentative explanation based on localized grain boundary migration is in accord with the experimental observations.

  11. Creep of Two-Phase Microstructures for Microelectronic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Heidi Linch [Univ. of California, Berkeley, CA (United States)

    1998-12-01

    The mechanical properties of low-melting temperature alloys are highly influenced by their creep behavior. This study investigates the dominant mechanisms that control creep behavior of two-phase, low-melting temperature alloys as a function of microstructure. The alloy systems selected for study were In-Ag and Sn-Bi because their eutectic compositions represent distinctly different microstructure.” The In-Ag eutectic contains a discontinuous phase while the Sn-Bi eutectic consists of two continuous phases. In addition, this work generates useful engineering data on Pb-free alloys with a joint specimen geometry that simulates microstructure found in microelectronic applications. The use of joint test specimens allows for observations regarding the practical attainability of superplastic microstructure in real solder joints by varying the cooling rate. Steady-state creep properties of In-Ag eutectic, Sn-Bi eutectic, Sn-xBi solid-solution and pure Bi joints have been measured using constant load tests at temperatures ranging from O°C to 90°C. Constitutive equations are derived to describe the steady-state creep behavior for In-Ageutectic solder joints and Sn-xBi solid-solution joints. The data are well represented by an equation of the form proposed by Dom: a power-law equation applies to each independent creep mechanism. Rate-controlling creep mechanisms, as a function of applied shear stress, test temperature, and joint microstructure, are discussed. Literature data on the steady-state creep properties of Sn-Bi eutectic are reviewed and compared with the Sn-xBi solid-solution and pure Bi joint data measured in the current study. The role of constituent phases in controlling eutectic creep behavior is discussed for both alloy systems. In general, for continuous, two-phase microstructure, where each phase exhibits significantly different creep behavior, the harder or more creep resistant phase will dominate the creep behavior in a lamellar microstructure. If a

  12. Power law creep of polycarbonate by Berkovich nanoindentation

    Science.gov (United States)

    Gao, Chenghui; Liu, Ming

    2017-10-01

    Power-law creep of polycarbonate was investigated by Berkovich indentation under three different conditions at room temperature, namely: constant displacement rate condition, constant displacement loading condition, and constant ratio of loading rate over load condition. Only the data during the loading process were analysed, and the experiments under different loading conditions gave consistent results that accorded well with theoretical prediction by dimensional analysis of indentation of power-law creep material. Material constants were characterized by curve fitting of the experimental results with theoretical equations, and the power law exponent for the power-law creep relation was found to be about 0.138 for the notably soft polycarbonate.

  13. Timer-based data acquisitioning of creep testing machines

    International Nuclear Information System (INIS)

    Rana, M.A.; Farooq, M.A.; Ali, L.

    1998-01-01

    Duration of a creep test may be short or long term extending over several years. Continuous operation of a computer for automatic data acquisition of creep testing machines is useless. Timer based data acquisitioning of the machines already interface with IBM-Pc/AT and compatibles has been streamlined for economical use of the computer. A locally designed and fabricated timer has been introduced in the system in this regard to meet the requirements of the system. The timer switches on the computer according to pre scheduled interval of time of capture creep data in Real time. The periodically captured data is logged on the hard disk for analysis and report generation. (author)

  14. Interfacing and data acquisitioning of creep testing machines

    International Nuclear Information System (INIS)

    Rana, M.A.; Ahmad, Z.; Farooq, M.A.; Ali, L.; Mushtaq, N.

    1998-05-01

    Automation of DSM-6100-CREEP TESTING MACHINES is made by using an IBM PC/XT/AT compatibles along with DAS-16 High Speed Analog I/O board. Creep test parameters namely force, temperature and LVDTs (Linear Variable Differential Transducer) left and right are calibrated. Empirical formula for each parameter is developed to convert data, which is received in the form of counts, into engineering units. LVDT controller module is designed and fabricated to handle two LVDTs for data acquisition of a creep test required for it. (author)

  15. The constitutive representation of high-temperature creep damage

    Science.gov (United States)

    Chan, K. S.

    1988-01-01

    The elastic-viscoplastic constitutive equations of Bodner-Partom were applied to modeling creep damage in a high temperature Ni-alloy, B1900 + Hf. Both tertiary creep in bulk materials and creep crack growth in flawed materials were considered. In the latter case, the energy rate line integral was used for characterizing the crack driving force, and the rate of crack extension was computed using a local damage formulation that assumed fracture was controlled by cavitation occurring within the crack-tip process zone. The results of this investigation were used to assess the evolution equation for isotropic damage utilized in the Bodner-Partom constitutive equations.

  16. CREEP STRAIN CORRELATION FOR IRRADIATED CLADDING

    International Nuclear Information System (INIS)

    P. Macheret

    2001-01-01

    In an attempt to predict the creep deformation of spent nuclear fuel cladding under the repository conditions, different correlations have been developed. One of them, which will be referred to as Murty's correlation in the following, and whose expression is given in Henningson (1998), was developed on the basis of experimental points related to unirradiated Zircaloy cladding (Henningson 1998, p. 56). The objective of this calculation is to adapt Murty's correlation to experimental points pertaining to irradiated Zircaloy cladding. The scope of the calculation is provided by the range of experimental parameters characterized by Zircaloy cladding temperature between 292 C and 420 C, hoop stress between 50 and 630 MPa, and test time extending to 8000 h. As for the burnup of the experimental samples, it ranges between 0.478 and 64 MWd/kgU (i.e., megawatt day per kilogram of uranium), but this is not a parameter of the adapted correlation

  17. Understanding effects of microstructural inhomogeneity on creep response – New approaches to improve the creep resistance in magnesium alloys

    Directory of Open Access Journals (Sweden)

    Yuanding Huang

    2014-06-01

    Full Text Available Previous investigations indicate that the creep resistance of magnesium alloys is proportional to the stability of precipitated intermetallic phases at grain boundaries. These stable intermetallic phases were considered to be effective to suppress the deformation by grain boundary sliding, leading to the improvement of creep properties. Based on this point, adding the alloying elements to form the stable intermetallics with high melting point became a popular way to develop the new creep resistant magnesium alloys. The present investigation, however, shows that the creep properties of binary Mg–Sn alloy are still poor even though the addition of Sn possibly results in the precipitation of thermal stable Mg2Sn at grain boundaries. That means other possible mechanisms function to affect the creep response. It is finally found that the poor creep resistance is attributed to the segregation of Sn at dendritic and grain boundaries. Based on this observation, new approaches to improve the creep resistance are suggested for magnesium alloys because most currently magnesium alloys have the commonality with the Mg–Sn alloys.

  18. Classification of titanium dioxide

    International Nuclear Information System (INIS)

    Macias B, L.R.; Garcia C, R.M.; Maya M, M.E.; Ita T, A. De; Palacios G, J.

    2002-01-01

    In this work the X-ray diffraction (XRD), Scanning Electron Microscopy (Sem) and the X-ray Dispersive Energy Spectroscopy techniques are used with the purpose to achieve a complete identification of phases and mixture of phases of a crystalline material as titanium dioxide. The problem for solving consists of being able to distinguish a sample of titanium dioxide being different than a titanium dioxide pigment. A standard sample of titanium dioxide with NIST certificate is used, which indicates a purity of 99.74% for the TiO 2 . The following way is recommended to proceed: a)To make an analysis by means of X-ray diffraction technique to the sample of titanium dioxide pigment and on the standard of titanium dioxide waiting not find differences. b) To make a chemical analysis by the X-ray Dispersive Energy Spectroscopy via in a microscope, taking advantage of the high vacuum since it is oxygen which is analysed and if it is concluded that the aluminium oxide appears in a greater proportion to 1% it is established that is a titanium dioxide pigment, but if it is lesser then it will be only titanium dioxide. This type of analysis is an application of the nuclear techniques useful for the tariff classification of merchandise which is considered as of difficult recognition. (Author)

  19. Uranium dioxide pellets

    International Nuclear Information System (INIS)

    Zawidzki, T.W.

    1979-01-01

    Sintered uranium dioxide pellets composed of particles of size > 50 microns suitable for power reactor use are made by incorporating a small amount of sulphur into the uranium dioxide before sintering. The increase in grain size achieved results in an improvement in overall efficiency when such pellets are used in a power reactor. (author)

  20. In-situ Creep Testing Capability Development for Advanced Test Reactor

    Energy Technology Data Exchange (ETDEWEB)

    B. G. Kim; J. L. Rempe; D. L. Knudson; K. G. Condie; B. H. Sencer

    2010-08-01

    Creep is the slow, time-dependent strain that occurs in a material under a constant strees (or load) at high temperature. High temperature is a relative term, dependent on the materials being evaluated. A typical creep curve is shown in Figure 1-1. In a creep test, a constant load is applied to a tensile specimen maintained at a constant temperature. Strain is then measured over a period of time. The slope of the curve, identified in the figure below, is the strain rate of the test during Stage II or the creep rate of the material. Primary creep, Stage I, is a period of decreasing creep rate due to work hardening of the material. Primary creep is a period of primarily transient creep. During this period, deformation takes place and the resistance to creep increases until Stage II, Secondary creep. Stage II creep is a period with a roughly constant creep rate. Stage II is referred to as steady-state creep because a balance is achieved between the work hardening and annealing (thermal softening) processes. Tertiary creep, Stage III, occurs when there is a reduction in cross sectional area due to necking or effective reduction in area due to internal void formation; that is, the creep rate increases due to necking of the specimen and the associated increase in local stress.

  1. Non-contacting creep strain determination at 550 deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Z.; Zarrabi, K.; Humphries, S.; Croker, A.; Small, R

    2003-06-01

    The digital speckle correlation technique (DSCT) is a non-contacting and whole field displacement/strain measurement system that has been successfully applied to a variety of applications. The technique is based on correlating the speckle surface of the object before and after deformation. It is best suited for flat surfaces. Creep deformation may, however, cause decorrelation of the speckle surface. The ability of DSCT to measure creep displacement/strain fields at 550 deg. C using 2.25%Cr 1%Mo steel specimens was evaluated. The specimens were cylindrical so that the effect of a non-flat surface was also included. Results show that DSCT can measure creep displacement and strain fields under laboratory conditions with less than 5% error. Further research and development work are required to assess the applicability of DSCT for creep displacement/strain measurements under field conditions.

  2. Behaviour of Epoxy Silica Nanocomposites Under Static and Creep Loading

    Science.gov (United States)

    Constantinescu, Dan Mihai; Picu, Radu Catalin; Sandu, Marin; Apostol, Dragos Alexandru; Sandu, Adriana; Baciu, Florin

    2017-12-01

    Specific manufacturing technologies were applied for the fabrication of epoxy-based nanocomposites with silica nanoparticles. For dispersing the fillers in the epoxy resin special equipment such as a shear mixer and a high energy sonicator with temperature control were used. Both functionalized and unfunctionalized silica nanoparticles were added in three epoxy resins. The considered filling fraction was in most cases 0.1, 0.3 and 0.5 wt%.. The obtained nanocomposites were subjected to monotonic uniaxial and creep loading at room temperature. The static mechanical properties were not significantly improved regardless the filler percentage and type of epoxy resin. Under creep loading, by increasing the stress level, the nanocomposite with 0.1 wt% silica creeps less than all other materials. Also the creep rate is reduced by adding silica nanofillers.

  3. Accelerated creep of Ni-YSZ anodes during reduction

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Greco, Fabio; Ni, De Wei

    2014-01-01

    load-carrying component. In this work we report on a new creep-reduction phenomenon observed to take place during the reduction process itself, where stresses are relaxed at a rate much faster (~×104) than during operation where the anode is in fully reduced state. Furthermore, samples exposed...... to a very small tensile stress (0.004 MPa) were observed to expand during reduction, which is in contrast with reports in literature [Ref].The “accelerated” creep has a tremendous impact on the stress field in an operating SOFC stack. Creep experiments, where carried out on NiO-YSZ anode support structures...... loaded in three point bending or uniaxial tension and the deformations recorded during the reduction process. The fast creep is observed only during the reduction, but due to the extremely high rate this will effectively relax all the residual compressive stresses in the electrolyte at the reduction...

  4. Does light attract piglets to the creep area?

    DEFF Research Database (Denmark)

    Larsen, Mona Lilian Vestbjerg; Pedersen, Lene Juul

    2015-01-01

    of the creep area and whether light in the creep area works as an attractant on piglets. A total of 39 sows, divided between two batches, were randomly distributed to three heat source treatments: (1) standard infrared heat lamp (CONT, n=19), (2) eHeat with light (EL, n=10) and (3) eHeat without light (ENL, n...... and was lower in batch 1 compared with batch 2. Seen from the present results, neither eHeat nor light worked as an attractant on piglets; in contrast, piglets preferred to sleep in the dark and it would therefore be recommended to turn off the light in the creep area during darkness. Heating up the creep area...

  5. Composite Analysis of Concrete - Creep, Relaxation and Eigenstrain/stress

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    1996-01-01

    results on creep, shrinkage, and internal stresses caused by drying shrinkage reported in the literature on the mechanical behavior of mature concretes.Shrinkage (autogeneous or drying) of mortar and concrete and associated internal stress states are examples of analysis made in this report......A composite-rheological model of concrete is presented by which consistent predictions of creep, relaxation, and internal stresses can be made from known concrete composition, age at loading, and climatic conditions. No other existing "creep prediction method" offers these possibilities in one...... approach.The model is successfully justified comparing predicted results with recent experimental data obtained in tests made at the Danish Technological Institute and at the Technical University of Denmark on creep, relaxation, and shrinkage of very young concretes (hours) - and also with experimental...

  6. Influence of specimen size on the creep of rock salt

    International Nuclear Information System (INIS)

    Senseny, P.E.

    1982-01-01

    Triaxial compression creep data for Avery Island dome salt are analyzed to determine the influence of specimen size on creep deformation. Laboratory experiments were performed on 50- and 100-mm-diameter specimens in the temperature range from 25 to 200 0 C and the axial stress difference range from 2.5 to 31.0 MPa. The strain-vs-time data from each test are divided into transient and steady-state components. Results of statistical analysis of these data show that transient creep of the small specimens is a stronger function of stress, temperature, and time than is transient creep of the larger specimens. Analysis of the steady-state data show no size effect, however. 14 references, 7 figures, 3 tables

  7. Mechanisms for tertiary creep of single crystal superalloy

    Science.gov (United States)

    Staroselsky, Alexander; Cassenti, Brice

    2008-12-01

    During the thermal-mechanical loading of high temperature single crystal turbine components, all three creep—stages: primary, secondary and tertiary, manifest themselves and, hence, none of them can be neglected. The development of a creep law that includes all three stages is especially important in the case of non-homogeneous thermal loading of the component where significant stress redistribution and relaxation will result. Thus, local creep analysis is crucial for proper design of damage tolerant airfoils. We have developed a crystallographic-based constitutive model and fully coupled it with damage kinetics. The model extends existing approaches for cyclic and thermal-cyclic loading of anisotropic elasto-viscoplastic deformation behavior and damage kinetics of single-crystal materials, allowing prediction of tertiary creep and failure initiation of high temperature components. Our damage model bridges the gap between dislocation dynamics and the continuum mechanics scales and can be used to represent tertiary as well as primary and secondary creep.

  8. Development of Creep Constitutive Equation for Low-Alloy Steel

    International Nuclear Information System (INIS)

    Jeong, Kwang J.; Lim, Joon; Hwang, Il S.; Kim, Hee D.; Pilch, Martin M.; Chu, Tze Y.

    2003-01-01

    High-temperature creep tests were performed with an SA533B1 low-alloy steel under both constant load and constant stress conditions. Using the measured minimum creep strain rates as a function of stress and temperature, least-square fittings were made into a Bailey-Norton-type power law equation. Based on the constant stress test results, a constitutive equation was developed for steady-state creep. The constitutive equation was then implemented in elastic-viscoplastic analysis of the lower head of a pressurized water reactor's reactor pressure vessel using a commercial FEM code named ABAQUS 5.8. The FEM model was validated using measured data from the lower head failure experiment conducted at the Sandia National Laboratories. The FEM model using the creep constitutive equation was shown to be capable of accurately predicting the lower head deformation behavior. Additional work, however, is needed to rationalize apparent inconsistency between the constant load data and constant stress data

  9. Review of creep deformation and rupture mechanism of P91 alloy for the development of creep damage constitutive equations under low stress level

    OpenAIRE

    An, Lili; Xu, Qiang; Xu, Donglai; Lu, Zhongyu

    2013-01-01

    This paper presents a review of creep deformation and rupture mechanism of P91 alloy for the development of its creep damage constitutive equations under lower stress level. Creep damage is one of the serious problems for the high temperature industries and computational approach (such as continuum damage mechanics) has been developed and used, complementary to the experimental approach, to assist safe operation. However, there are no ready creep damage constitutive equations to be used for p...

  10. Magnetic measurement of creep damage: modeling and measurement

    Science.gov (United States)

    Sablik, Martin J.; Jiles, David C.

    1996-11-01

    Results of inspection of creep damage by magnetic hysteresis measurements on Cr-Mo steel are presented. It is shown that structure-sensitive parameters such as coercivity, remanence and hysteresis loss are sensitive to creep damage. Previous metallurgical studies have shown that creep changes the microstructure of he material by introducing voids, dislocations, and grain boundary cavities. As cavities develop, dislocations and voids move out to grain boundaries; therefore, the total pinning sources for domain wall motion are reduced.This, together with the introduction of a demagnetizing field due to the cavities, results in the decrease of both coercivity, remanence and hence, concomitantly, hysteresis loss. Incorporating these structural effects into a magnetomechanical hysteresis model developed previously by us produces numerical variations of coercivity, remanence and hysteresis loss consistent with what is measured. The magnetic model has therefore been used to obtain appropriately modified magnetization curves for each element of creep-damaged material in a finite element (FE) calculation. The FE calculation has been used to simulate magnetic detection of non-uniform creep damage around a seam weld in a 2.25 Cr 1Mo steam pipe. In particular, in the simulation, a magnetic C-core with primary and secondary coils was placed with its pole pieces flush against the specimen in the vicinity of the weld. The secondary emf was shown to be reduced when creep damage was present inside the pipe wall at the cusp of the weld and in the vicinity of the cusp. The calculation showed that the C- core detected creep damage best if it spanned the weld seam width and if the current in the primary was such that the C- core was not magnetically saturated. Experimental measurements also exhibited the dip predicted in emf, but the measurements are not yet conclusive because the effects of magnetic property changes of weld materials, heat- affected material, and base material have

  11. Micromechanics of intergranular creep failure under cyclic loading

    DEFF Research Database (Denmark)

    van der Giessen, Erik; Tvergaard, Viggo

    1996-01-01

    boundaries are modelled individually. The model incorporates power-law creep of the grains, viscous grain boundary sliding between grains as well as the nucleation and growth of grain boundary cavities until they coalesce and form microcracks. Study of a limiting case with a facet-size microcrack reveals....... The analyses provide some new understanding that helps to explain the sometimes peculiar behaviour under balanced cyclic creep. Copyright (C) 1996 Acta Metallurgica Inc....

  12. Creep small-punch testing and its numerical simulations

    Czech Academy of Sciences Publication Activity Database

    Dymáček, Petr; Milička, Karel

    2009-01-01

    Roč. 510-511, - (2009), s. 444-449 ISSN 0921-5093. [Creep 2008. Bayreuth, 04.05.2008-09.05.2008] R&D Projects: GA AV ČR(CZ) IAA200410801 Institutional research plan: CEZ:AV0Z20410507 Keywords : creep * small punch test * finite element method Subject RIV: JG - Metallurgy Impact factor: 1.901, year: 2009

  13. Physical mechanisms of radiation induced creep in metals

    International Nuclear Information System (INIS)

    Borodin, V.A.; Ryazanov, A.I.

    1990-01-01

    Analysis of available experimental data has been conducted. It enables to correlate reliably the character of evolution of dislocation structure of irradiated materials with different stages of radiation induced creep. This provides reliable basis for the general conclusions concerning the character of some parametric dependences of deformation rate of these materials. Analysis of different modern theoretical models enables to evaluate regions of their applicability and their relative significance for radiation induced creep description. 20 refs.; 2 figs.; 1 tab

  14. A Creep Model for High-Density Snow

    Science.gov (United States)

    2017-04-01

    plotted as an additional parameter. From these data , I extracted the trend in Y vs. ρ and provide this as a look-up table in ABAQUS (Table 2). Table 2...could be used in the standard ABAQUS creep model. Comparing model-predicted strain and settlement to published data shows that the secondary creep...Available laboratory data helped to determine the parameters for these models. These models were recast into a form compatible with the ABAQUS finite

  15. Creep in jointed rock masses. State of knowledge

    Energy Technology Data Exchange (ETDEWEB)

    Glamheden, Rune (Golder Associates AB (Sweden)); Hoekmark, Harald (Clay Technology AB, Lund (Sweden))

    2010-06-15

    To describe creep behaviour in hard rock masses in a physically realistic way, elaborate models including various combinations of dash pots, spring elements and sliders would be needed. According to our knowledge, there are at present no numerical tools available that can handle such a creep model. In addition, there are no records over sufficient long time periods of tunnel convergence in crystalline rock that could be used to determine or calibrate values for the model parameters. A possible method to perform bounding estimates of creep movements around openings in a repository may be to use distinct element codes with standard built-in elasto-plastic models. By locally reducing the fracture shear strength near the underground openings a relaxation of fracture shear loads is reached. The accumulated displacements may then represent the maximum possible effects of creep that can take place in a jointed rock mass without reference to the actual time it takes to reach the displacements. Estimates based on results from analyses where all shear stresses are allowed to disappear completely will, however, be over-conservative. To be able to set up and analyse reasonably realistic numerical models with the proposed method, further assumptions regarding the creep movements and the creep region around the opening have to be made. The purpose of this report is to present support for such assumptions as found in the literature.

  16. An experimental and theoretical investigation of creep buckling

    International Nuclear Information System (INIS)

    Ohya, H.

    1977-01-01

    The purpose of the present paper is to investigate creep buckling phenomena and the methods of analysis. Creep buckling experiments were performed on aluminum alloy 2024-T4 cylindrical shells having radius to thickness ratios of 16, 25, 50 and 80, in single, double and triple step axial compression at 250 0 C. It was observed that buckling occurred at one of the edges and the buckling mode depended on the radius to thickness ratio and also on the applied stress level. Thicker cylinders buckled in axisymmetric mode. Thinner ones under higher applied stress levels buckled in the asymmetric mode, whereas they under lower applied stress levels buckled in the axisymmetric mode. Creep buckling times were obtained from end shortening record of the cylinders. Experimental results were compared with theoretical values obtained by the following two methods. One is a simplified method to estimate buckling times, proposed by Gerard et al., Papirno et al. and others. The method is based on the fact that the creep buckling solutions are analogous to those of plastic buckling under a certain assumption. It was found that the bukling times could be reasonably estimated by this simplified method. The other is a finite element computer program for axisymmetric thin shells. This program is based on the incremental theory and can treat thermoelastoplastic creep analysis of axisymmetric thin shells with large deflection. Creep deformation behavior of cylindrical shells under axial compression and buckling times were calculated by the program and the effects of plasticity on buckling times were also investigated

  17. Irradiation creep and growth of zircaloy-4 tubes

    International Nuclear Information System (INIS)

    Lansiart, S.; Darchis, L.; Pelchat, J.

    1990-01-01

    The influence of temperature and fast neutron flux on irradiation creep and growth of stress relieved zircaloy-4 pressurized tubes has been derived from experimental irradiations in NaK, performed up to 2.5 10 25 n.m -2 in the temperature range [280, 350] 0 C. A significant influence of temperature on axial growth has been observed: at 280 0 C the elongation can no longer be expressed as a linear function of fluence as for the 350 0 C irradiation temperature; diametral growth, on the other hand, always appears negligible. Irradiation creep obviously depends on temperature too; the diametral strain (including thermal part) has been modelled as a sum of primary and secondary terms, the former being independent of fluence. For the tubing considered it is observed that the ranking of the different batches, with respect to diametral creep resistance, is the same before and under irradiation. Concerning axial creep strain the stress relieved material behaves as does an isotropic tube. This is not the case of recrystallized zircaloy-4 F, which shows a non negligible axial deformation, related to the diametral creep one, even though this diametral irradiation creep strain is strongly reduced comparatively to that of the stress relieved material. The comparison of the two materials growth rates is more complex since their dependence on temperature and flux differs

  18. Creep in jointed rock masses. State of knowledge

    International Nuclear Information System (INIS)

    Glamheden, Rune; Hoekmark, Harald

    2010-06-01

    To describe creep behaviour in hard rock masses in a physically realistic way, elaborate models including various combinations of dash pots, spring elements and sliders would be needed. According to our knowledge, there are at present no numerical tools available that can handle such a creep model. In addition, there are no records over sufficient long time periods of tunnel convergence in crystalline rock that could be used to determine or calibrate values for the model parameters. A possible method to perform bounding estimates of creep movements around openings in a repository may be to use distinct element codes with standard built-in elasto-plastic models. By locally reducing the fracture shear strength near the underground openings a relaxation of fracture shear loads is reached. The accumulated displacements may then represent the maximum possible effects of creep that can take place in a jointed rock mass without reference to the actual time it takes to reach the displacements. Estimates based on results from analyses where all shear stresses are allowed to disappear completely will, however, be over-conservative. To be able to set up and analyse reasonably realistic numerical models with the proposed method, further assumptions regarding the creep movements and the creep region around the opening have to be made. The purpose of this report is to present support for such assumptions as found in the literature

  19. Interlaboratory verification of silicon nitride tensile creep properties

    Energy Technology Data Exchange (ETDEWEB)

    Luecke, W.E.; Wiederhorn, S.M. [National Inst. of Standards and Technology, Gaithersburg, MD (United States). Materials Science and Engineering Lab.

    1997-04-01

    Five laboratories tested NIST-supplied, pin-loaded, 76-mm-long tensile creep specimens at 1,400 C under a 150 MPa load using flag-based, laser extensometry. The laboratories reported failure time and strain and supplied the individual creep curves. Only one of the laboratories produced failure times that were significantly less than the others. It is likely that their reduced failure times resulted from small load calibration and test temperature errors. After steps were taken to ameliorate these problems, three additional tests yielded failure times that agreed with those of the other four laboratories. Although the times to failure from the four laboratories that initially agreed were statistically indistinguishable, their creep curves exhibited subtle differences. These differences probably arose because the laboratories used different gage length definitions. When the authors recalculated the creep curves to the same gage length definition, the differences between the four laboratories whose times to failure agreed, vanished. Although a number of the specimens exhibited edge chips, creep cracks, and obvious chemical interactions with the flags, the presence of these defects did not reduce the time or strain to failure. Two additional creep tests in the laboratory, using specimens that were grossly misaligned, yielded failure times and strains that were commensurate with those from well-aligned specimens.

  20. Magnetic flux creep in HTSC and Anderson-Kim theory

    International Nuclear Information System (INIS)

    Lykov, A.N.

    2014-01-01

    The theoretical and experimental data on flux creep in high-temperature superconductors (HTSC) were analyzed in the review paper. On the one hand, the main attention is paid to the most striking experimental results which have had a significant influence on the investigations of flux creep in HTSC. On the other hand, the analysis of theoretical studies is concentrated on the works, which explain the features of flux creep on the basis of the Anderson-Kim (AK) theory modifications, and received previously unsufficient attention. However, it turned out that the modified AK theory could explain a lot of features of flux creep in HTSC: the scaling behaviour of current-voltage curves of HTSC, the finite rate of flux creep at ultra low temperatures, the logarithmic dependence of effective pinning potential as a function of transport current and its decrease with temperature. The harmonic potential field which is used in this approach makes it possible to solve accurately the both problems: viscous vortex motion and flux creep in this field. Moreover the distribution of pinning potential and the interaction of vortices with each other are taken into account in the approach. Thus, the modification of the AK theory consists, essentially, in its detailed elaboration and approaching to real situations in superconductors

  1. A Critical Analysis of the Conventionally Employed Creep Lifing Methods

    Directory of Open Access Journals (Sweden)

    Zakaria Abdallah

    2014-04-01

    Full Text Available The deformation of structural alloys presents problems for power plants and aerospace applications due to the demand for elevated temperatures for higher efficiencies and reductions in greenhouse gas emissions. The materials used in such applications experience harsh environments which may lead to deformation and failure of critical components. To avoid such catastrophic failures and also increase efficiency, future designs must utilise novel/improved alloy systems with enhanced temperature capability. In recognising this issue, a detailed understanding of creep is essential for the success of these designs by ensuring components do not experience excessive deformation which may ultimately lead to failure. To achieve this, a variety of parametric methods have been developed to quantify creep and creep fracture in high temperature applications. This study reviews a number of well-known traditionally employed creep lifing methods with some more recent approaches also included. The first section of this paper focuses on predicting the long-term creep rupture properties which is an area of interest for the power generation sector. The second section looks at pre-defined strains and the re-production of full creep curves based on available data which is pertinent to the aerospace industry where components are replaced before failure.

  2. ANSYS Creep-Fatigue Assessment tool for EUROFER97 components

    Directory of Open Access Journals (Sweden)

    M. Mahler

    2016-12-01

    Full Text Available The damage caused by creep-fatigue is an important factor for materials at high temperatures. For in-vessel components of fusion reactors the material EUROFER97 is a candidate for structural application where it is subjected to irradiation and cyclic thermo-mechanical loads. To be able to evaluate fusion reactor components reliably, creep-fatigue damage has to be taken into account. In the frame of Engineering Data and Design Integration (EDDI in EUROfusion Technology Work Programme rapid and easy design evaluation is very important to predict the critical regions under typical fusion reactor loading conditions. The presented Creep-Fatigue Assessment (CFA tool is based on the creep-fatigue rules in ASME Boiler Pressure Vessel Code (BPVC Section 3 Division 1 Subsection NH which was adapted to the material EUROFER97 and developed for ANSYS. The CFA tool uses the local stress, maximum elastic strain range and temperature from the elastic analysis of the component performed with ANSYS. For the assessment design fatigue and stress to rupture curves of EUROFER97 as well as isochronous stress vs. strain curves determined by a constitutive model considering irradiation influence are used to deal with creep-fatigue damage. As a result allowable number of cycles based on creep-fatigue damage interaction under given hold times and irradiation rates is obtained. This tool can be coupled with ANSYS MAPDL and ANSYS Workbench utilizing MAPDL script files.

  3. Viscoelastic modelling of Zircaloy cladding in-pile transient creep

    Energy Technology Data Exchange (ETDEWEB)

    Tulkki, Ville, E-mail: ville.tulkki@vtt.fi; Ikonen, Timo

    2015-02-15

    In fuel behaviour modelling accurate description of the cladding stress response is important for both operational and safety considerations. The cladding creep determines in part the width of the gas gap, the duration to pellet-cladding contact and the stresses to the cladding due to the pellet expansion. Conventionally the strain hardening rule has been used to describe the creep response to transient loads in engineering applications. However, it has been well documented that the strain hardening rule does not describe well results of tests with load drops or reversals. In our earlier work we have developed a model for primary creep which can be used to simulate the in- and out-of-pile creep tests. Since then several creep experiments have entered into public domain. In this paper we develop the model formulation based on the theory of viscoelasticity, and show that this model can reproduce the new experimental results. We also show that the creep strain recovery encountered in experimental measurements can be explained by viscoelastic behaviour.

  4. Verification of creep performance of a ceramic gas turbine blade

    Energy Technology Data Exchange (ETDEWEB)

    Lin, H.T.; Becher, P.F.; Ferber, M.K. [Oak Ridge National Lab., TN (United States). Metals and Ceramics Div.; Parthasarathy, V. [Solar Turbines Inc., San Diego, CA (United States)

    1998-03-01

    Tensile creep tests were carried out on a Norton NT164 silicon nitride ceramic turbine blade containing 4 wt. % Y{sub 2}O{sub 3} sintering additive at 1,370 C in air under selected stress levels. The objective of this study was to measure the creep properties of test specimens extracted from a complex shaped ceramic gas turbine blade to verify the response of actual components. The creep results indicated that specimens from both the airfoil and dovetail sections exhibited creep rates that were about 4 to 100 times higher than those obtained from both the buttonhead and dogbone creep specimens machined from the developmental billets fabricated with the same composition and processing procedures. Electron microscopy analyses suggested that high creep rates and short lifetimes observed in specimens extracted from the turbine blade resulted from a higher glassy phase(s) content and smaller number density of elongated grain microstructure. Silicon nitride ceramics with an in-situ reinforced elongated microstructure have been the primary candidates for both advanced automotive and land-based gas turbine engine applications.

  5. Prediction of long time creep rupture properties of welded joints using the results of short duration creep crack incubation tests

    International Nuclear Information System (INIS)

    Hosseini, E.

    2013-01-01

    This dissertation submitted to the Swiss Federal Institute of Technology ETH in Zurich examines the applicability of the LICON methodology for the prediction of long-time creep rupture strength of a dissimilar metal weld. The LICON methodology is an approach for predicting the lifetime of materials under creep loading conditions. It predicts long-time uniaxial creep strength using the results from several short duration creep crack incubation tests in conjunction with the outcome of a mechanical analysis on the test-piece. This study has re-examined the previous application of the LICON methodology for 9%Cr and 1CrMoV steels. It has shown that application of the original Lion method (based on reference stress solutions) for certain materials is not appropriate. This study therefore proposes a new development for the Lion approach which uses finite-element analysis to account for the generated multiaxial stress states within welded uniaxial test-pieces

  6. EFAM GTP-CREEP 02 - the GKSS test procedure for determining the creep crack extension of materials

    International Nuclear Information System (INIS)

    Schwalbe, K.H.

    2002-01-01

    This document describes a fracture mechanics method in procedural form for determining the creep crack extension of materials. It is based on the unified fracture mechanics test method EFAM GTP 02, the ASTM standard E 1457-98, activities of VAMAS TWA 19, and GKSS experience in creep crack extension testing. It introduces novel features such as the rate of the δ 5 crack tip opening displacement, the crack tip opening angle, and the middle cracked tension specimen. (orig.) [de

  7. Microstructural development in tension and compression creep of magnesium alloy AE42

    Energy Technology Data Exchange (ETDEWEB)

    Dieringa, H.; Bowles, A.; Hort, N.; Kainer, K.U. [GKSS Research Center, Center for Magnesium Technology, Geesthacht (Germany)

    2005-07-01

    Investigations on creep resistant magnesium alloy AE42 were performed in creep tests in compressive and tensile mode. Minimum creep rates and stress exponents n were calculated and compared for tests with the same temperature and load. Linear fits of minimum creep rates in log/log plots at all temperatures shows a similar behavior. The higher the load the bigger is the difference between minimum creep rate at tensile and compression tests. At loads around 40 MPa rates adjust to similar values. During creep microstructural evolution is different. Wide twins form during compressive creep tests whereas double-directed fine twins with an angle of approximately 51 are formed during tensile creep test. The difference in twinning is supposed to be one of the reason for different creep rates. (orig.)

  8. Creep behaviour of porous metal supports for solid oxide fuel cells

    DEFF Research Database (Denmark)

    Boccaccini, Dino; Frandsen, Henrik Lund; Sudireddy, Bhaskar Reddy

    2014-01-01

    The creep behaviour of porous ironechromium alloy used as solid oxide fuel cell support was investigated, and the creep parameters are compared with those of dense strips of similar composition under different testing conditions. The creep parameters were determined using a thermo-mechanical anal......The creep behaviour of porous ironechromium alloy used as solid oxide fuel cell support was investigated, and the creep parameters are compared with those of dense strips of similar composition under different testing conditions. The creep parameters were determined using a thermo......-mechanical analyser with applied stresses in the range from 1 to 15 MPa and temperatures between 650 and 800 _C. The GibsoneAshby and Mueller models developed for uniaxial creep of open-cell foams were used to analyse the results. The influence of scale formation on creep behaviour was assessed by comparing the creep...

  9. Comprehensive Creep and Thermophysical Performance of Refractory Materials

    Energy Technology Data Exchange (ETDEWEB)

    Ferber, M.K.; Wereszczak, A.; Hemrick, J.A.

    2006-06-29

    Furnace designers and refractory engineers recognize that optimized furnace superstructure design and refractory selection are needed as glass production furnaces are continually striving toward greater output and efficiencies. Harsher operating conditions test refractories to the limit, while changing production technology (such as the conversion to oxy-fuel from traditional air-fuel firing) can alter the way the materials perform [1-3]. Refractories for both oxy- and air-fuel fired furnace superstructures (see Fig. 1) are subjected to high temperatures that may cause them to creep excessively or subside during service if the refractory material is not creep resistant, or if it is subjected to high stress, or both. Furnace designers can ensure that superstructure structural integrity is maintained if the creep behavior of the refractory material is well understood and well represented by appropriate engineering creep models. Several issues limit the abilities of furnace designers to (1) choose the optimum refractory for their applications, (2) optimize the engineering design, or (3) predict the service mechanical integrity of their furnace superstructures. Published engineering creep data are essentially nonexistent for almost all commercially available refractories used for glass furnace superstructures. The limited data that do exist are supplied by the various refractory suppliers. Unfortunately, the suppliers generally have different ways of conducting their mechanical testing, and they interpret and report their data differently. This inconsistency makes it hard for furnace designers to draw fair comparisons between competing grades of candidate refractories. Furthermore, the refractory suppliers' data are often not available in a form that can be readily used for furnace design or for the prediction and design of long-term structural integrity of furnace superstructures. As a consequence, the U.S. Department of Energy (DOE) Industrial Technology Program

  10. AGC 2 Irradiation Creep Strain Data Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Windes, William E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rohrbaugh, David T. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Swank, W. David [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-08-01

    The Advanced Reactor Technologies Graphite Research and Development Program is conducting an extensive graphite irradiation experiment to provide data for licensing of a high temperature reactor (HTR) design. In past applications, graphite has been used effectively as a structural and moderator material in both research and commercial high temperature gas cooled reactor designs. Nuclear graphite H-451, used previously in the United States for nuclear reactor graphite components, is no longer available. New nuclear graphite grades have been developed and are considered suitable candidates for new HTR reactor designs. To support the design and licensing of HTR core components within a commercial reactor, a complete properties database must be developed for these current grades of graphite. Quantitative data on in service material performance are required for the physical, mechanical, and thermal properties of each graphite grade, with a specific emphasis on data accounting for the life limiting effects of irradiation creep on key physical properties of the HTR candidate graphite grades. Further details on the research and development activities and associated rationale required to qualify nuclear grade graphite for use within the HTR are documented in the graphite technology research and development plan.

  11. Creep test with use of miniaturized specimens

    Science.gov (United States)

    Chvostová, E.; Džugan, J.

    2017-02-01

    Application of the mini samples methods is very common especially for residual service life assessment of the components operating in the energy sector. Residual lifetime of operating device can be evaluated using standard tests, but these usually cannot be performed due to limited material amount that can be extracted from the components. It is possible to use in these cases a semi destructive sampling of materials and testing methods employing miniature specimens. This article deals with comparison of the creep results obtained with the use of on standard test bars and sub sized samples such as Small Punch Test and newly proposed miniature samples that are axially loaded. The experiment was performed on steam line steel CSN 15 128 after operation. Emphasis was put to practical use of the test results and therefore residual life was assessed with the use of standard and new mini specimens. The results obtained for standard and mini samples exhibit very good agreement without necessity of any correlation as in the case of SPT and thus much more straight forward approach can be applied even for “unknown materials”.

  12. Shakedown and ratchetting below the creep range

    International Nuclear Information System (INIS)

    Ponter, A.R.S.

    1983-01-01

    The report reviews current understanding of the behaviour of structure subject to variable mechanical and thermal loading below the creep range through a comparison of theoretical solutions and experimental studies. The particular characteristics of the austenitic stainless steels are emphasized in components subject to moderate primary loads and large thermal loads. The review shows that a clear classification of types of thermal loading is required in design. Two main classes, termed category A and B, exist which arise not from the magnitude of the thermal stresses but their extent through the material volume of the structure. In category A situations, the Bree plate problem being the prime example, the maximum thermal stresses occur over a volume of the structure which does not contain a mechanism of failure. As a result very large thermal stresses may be withstood without ratchetting occurring for sufficiently small mechanical loads. For category B situations, the maximum thermal stress occur within a volume of material which contains a mechanism of deformation. In such cases, the capacity of the structure to withstand thermal loading is limited by a variation of the maximum thermal stress at a material point of 2σsub(γ) where σsub(γ) is a suitably defined yield stress. This situation seems to be the most typical problem of the Liquid Metal Fast Reactor and the ''3Sm'' limit in the ASME III code restriction on secondary stress cannot be exceeded if ratchetting is to be prevented

  13. Creep Deformation and Fracture Processes in OF and OFP Copper

    International Nuclear Information System (INIS)

    Bowyer, William H.

    2004-10-01

    The literature on creep processes in many materials, including copper, has been thoroughly reviewed and complemented by Ashby and co-workers. They have provided physical models which describe the deformation and fracture processes with good qualitative and quantitative agreement with experimental data for many cases. A description of the deformation and fracture models is provided and the relevant equations are included in the appendices. Published data from the canister development programme has been compared with the predictions from the models. The purpose was to improve our understanding of (1) a reported benefit to creep performance which arises from additions of 50 ppm phosphorus to oxygen free (OF) copper, and (2) an observed transition from brittle to ductile failure in OF copper. The models adequately describe the general variations in the observed creep behaviour of the experimental materials. Steady state creep rates for OF copper are observed to be up to one order of magnitude higher than the model predicts for pure copper across a wide range of temperatures and stresses in the power law and power law breakdown regimes. For OF copper with 50ppm of phosphorus added (OFP copper), observed steady state creep rates in the power law breakdown regime are up to one order of magnitude lower than the model predicts for pure copper. Creep lives in the experimental OFP material are also higher than creep lives for OF material under similar conditions. The lower creep deformation rates and the longer creep lives of OFP material are attributed the known effects of phosphorus on recovery in copper. The model predicts that the same mechanism will improve creep lives under repository conditions. It is suggested that the factor of improvement under repository conditions will be less than the factor which is observed in the power law breakdown regime. Predicted creep lives, based on measured steady state creep rates and stress exponents ('n' values) are in good agreement

  14. Carbon dioxide removal process

    Science.gov (United States)

    Baker, Richard W.; Da Costa, Andre R.; Lokhandwala, Kaaeid A.

    2003-11-18

    A process and apparatus for separating carbon dioxide from gas, especially natural gas, that also contains C.sub.3+ hydrocarbons. The invention uses two or three membrane separation steps, optionally in conjunction with cooling/condensation under pressure, to yield a lighter, sweeter product natural gas stream, and/or a carbon dioxide stream of reinjection quality and/or a natural gas liquids (NGL) stream.

  15. Super long-term creep tests of advanced HP and IP rotor steels

    Energy Technology Data Exchange (ETDEWEB)

    Tchizhik, A.A. [The Polzunov Central Boiler and Turbine Institute, Department the Fatigue Life of Materials for Power Plans Equipment, St. Petersburg (Russian Federation)

    1998-12-31

    A creep model has been developed for predicting the long-term creep behavior, in excess of 200,000 h for advanced materials.The new creep theory is based on a continuum microdamage model and is used to calculate the fields of stress and strain and wedge and cavities damage in critical components of steam and gas turbines. The application of this new model increases the reliability and service life of modern turbines. The accuracy of the model to predict long - term creep behavior, creep ductility was verified using the data bank of super long-term creep tests of advanced materials. (orig.) 12 refs.

  16. High-temperature transient creep properties of CANDU pressure tubes

    International Nuclear Information System (INIS)

    Fong, R.W.L.; Chow, C.K.

    2002-06-01

    During a hypothetical large break loss-of-coolant accident (LOCA), the coolant flow would be reduced in some fuel channels and would stagnate and cause the fuel temperature to rise and overheat the pressure tube. The overheated pressure tube could balloon (creep radially) into contact with its moderator-cooled calandria tube. Upon contact, the stored thermal energy in the pressure tube is transferred to the calandria tube and into the moderator, which acts as a heat sink. For safety analyses, the modelling of fuel channel deformation behaviour during a large LOCA requires a sound knowledge of the high-temperature creep properties of Zr-2.5Nb pressure tubes. To this extent, a ballooning model to predict pressure-tube deformation was developed by Shewfelt et al., based on creep equations derived using uniaxial tensile specimens. It has been recognized, however, that there is an inherent variability in the high-temperature creep properties of CANDU pressure tubes. The variability, can be due to different tube-manufacturing practices, variations in chemical compositions, and changes in microstructure induced by irradiation during service in the reactor. It is important to quantify the variability of high-temperature creep properties so that accurate predictions on pressure-tube creep behaviour can be made. This paper summarizes recent data obtained from high-temperature uniaxial creep tests performed on specimens taken from both unirradiated (offcut) and irradiated pressure tubes, suggesting that the variability is attributed mainly to the initial differences in microstructure (grain size, shape and preferred orientation) and also from tube-to-tube variations in chemical composition, rather than due to irradiation exposure. These data will provide safety analysts with the means to quantify the uncertainties in the prediction of pressure-tube contact temperatures during a postulated large break LOCA. (author)

  17. French recent developments in support to rules for creep and creep-fatigue analyses

    International Nuclear Information System (INIS)

    Touboul, F.; Moulin, D.

    1997-01-01

    RCC-MR proposes Design rules for creep and creep-fatigue damage evaluation in zones with no geometrical discontinuities. Rules have been developed, based on the σ d concept, in order to consider zones with geometrical discontinuities. Rule for Weld are proposed in the paragraph relative to shell design rules and reduction coefficient due to material properties are given in Appendix A9. For fatigue analysis, last version of RCC-MR (1993) has proposed a reduction factor on fatigue curves (Jf value), derived from preliminary tests performed within European program. Studies have been carried out in order to have a better understanding of the phenomena involved in these fatigue reduction factors. Tests have been performed on large plates, with varying applied displacements, weld geometry, plate thickness, weld direction. It appears that material effect is not the only purpose to be considered but that it is necessary to think about the geometrical effect, linked to the welded zone dimensions, and the elastic follow-up effect between the two materials: base metal and weld metal. As a first approach, simplified calculations have been achieved with precise material characterization. Roche's method and Zarka method's give conservative result in comparison to tests results. (author). 3 refs, 4 tabs

  18. Steady state creep of Zr-Nb alloys in a temperature interval 350 to 5500C

    International Nuclear Information System (INIS)

    Pahutova, M.; Cadek, J.

    1976-01-01

    Creep of three Zr-Nb alloys (0.5, 2.5 and 4.5 wt% Nb) was investigated in a temperature interval 350 to 550 0 C using the isothermal creep test and transmission electron microscopy techniques. Relations between steady-state creep rate and applied stress were determined; the parameter of applied stress sensitivity of steady-state creep rate increases with the applied stress, reaching values sometimes greater than 30 at 350 0 C. The apparent activation energy of creep was determined and the mean effective stress in steady-state creep measured. Possible creep-rate controlling mechanisms were discussed, with the conclusion that the creep is most probably recovery-controlled. Relations between steady state flow stress and temperature suggest a significant contribution of an athermal deformation mechanism to the measured steady-state strain rate at low temperatures and high applied stresses. The creep-strengthening effect of niobium increases linearly with niobium concentration at high steady-state creep rates, while at low steady-state creep rates the optimum niobium concentration does not exceed 2.5%. This, together with the temperature sensitivity of the strengthening effect of niobium, was explained by structural stability decreasing as niobium concentration increases from 2.5 to 4.5%. Creep-controlling mechanisms for very low creep rates are discussed. (Auth.)

  19. Creep crack growth in phosphorus alloyed oxygen free copper

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Rui; Seitisleam, Facredin (Swerea KIMAB (Sweden)); Sandstroem, Rolf; Jin, Lai-Zhe (Materials Science and Engineering, Royal Inst. of Technology (Sweden))

    2011-01-15

    Using standard compact tension (CT) specimens taken from a pierce and draw cylinder, creep crack growth (CCG) has been studied in phosphorus-alloyed oxygen-free copper (Cu-OFP) parent metal at 22, 75, 175, and 215 deg C. Pre- and post-test metallography are performed. At higher temperatures the rupture time of CCG is shorter by a factor up of 65 than that of uniaxial at same stress/reference stress. At 175 and 215 deg C, crack does grow by creep about 10 mm before final instantaneous failure. In contrast, there is hardly any visible crack growth at 22 and 75 deg C. The tests were interrupted after 5000 to 13000 hours. For ruptured tests at 175 and 215 deg C, strongly elongated and deformed grains are observed adjacent to crack. Extensive and intergranular creep cavities and microcracks are found several mm around crack. For interrupted tests at 22 and 75 deg C, strongly elongated and deformed grains, creep cavities, as well as microcracks are observed close to crack tip. Surface cracks from both sides have initiated and grown about 45 deg to the load direction towards inside. For the interrupted tests, hardness adjacent to crack tip has more than doubled because of work hardening, or heavy deformation. This is consistent with large crack tip opening. The true strain at the crack tip is estimated to 10 and 4 for the tests at 22 and 75 deg C, respectively. The stress state behind the crack tip has been modelled with FEM. Stress relaxation after loading has also been taken into account. A model for the creep damage based on the creep strain rate has been formulated that can describe the uniaxial creep rupture data without fitting parameters. Based on the formulation for the creep damage, a model for the crack propagation has been set up. When the creep damage has reached the value unity in front of the crack tip, the crack is assumed to propagate. Taking multiaxial effects into account the observed life times of the CT specimens can be well described. The multiaxial

  20. Creep Behaviour of Fly Ash-Based Geopolymer Concrete

    Directory of Open Access Journals (Sweden)

    Wallah S.E.

    2010-01-01

    Full Text Available Fly ash-based geopolymer concrete is manufactured using fly ash as its source material and does not use Portland cement at all. Beside fly ash, alkaline solution is also utilized to make geopolymer paste which binds the aggregates to form geopolymer concrete. This paper presents the study of creep behaviour of fly ash-based geopolymer concrete. Four series of specimens with various compressive strengths were prepared to study its creep behaviour for the duration of test up to one year. The test method followed the procedures applied for Ordinary Portland Cement (OPC concrete. Test results show that fly ash-based geopolymer concrete undergoes low creep which is generally less than that of OPC concrete. After one year of loading, the results for specific creep of fly ash-based geopolymer concrete in this study ranges from 15 to 29 microstrain for concrete compressive strength 67–40 MPa respectively. From the test results, it is also found out that the creep coefficient of fly ash-based geopolymer concrete is about half of that predicted using Gilbert’s Method for OPC concrete.

  1. STUDY THE CREEP OF TUBULAR SHAPED FIBER REINFORCED COMPOSITES

    Directory of Open Access Journals (Sweden)

    Najat J. Saleh

    2013-05-01

    Full Text Available Inpresent work tubular –shaped fiber reinforced composites were manufactured byusing two types of resins ( Epoxy and unsaturated polyester and separatelyreinforced with glass, carbon and kevlar-49 fibers (filament and woven roving,hybrid reinforcement composites of these fibers were also prepared. The fiberswere wet wound on a mandrel using a purposely designed winding machine,developed by modifying an ordinary lathe, in winding angle of 55° for filament. A creep test was made of either the fulltube or specimens taken from it. Creep was found to increase upon reinforcementin accordance to the rule of mixture and mainly decided by the type of singleor hybridized fibers. The creep behavior, showed that the observed strain tendsto appear much faster at higher temperature as compared with that exhibited atroom temperate. The creep rate also found to be depending on fiber type, matrixtype, and the fiber /matrix bonding. The creep energy calculated fromexperimental observations was found to exhibit highest value for hybridizedreinforcement.

  2. Creep Behavior of Poly(lactic acid Based Biocomposites

    Directory of Open Access Journals (Sweden)

    Marco Morreale

    2017-04-01

    Full Text Available Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C. The results showed that the creep behavior of the composites is strongly influenced by the temperature and the woven fabrics used. As preliminary characterization, quasi-static tensile tests and dynamic mechanical tests were carried out on the composites. Furthermore, fabrics (both flax and jute were tested as received by means of quasi-static tests and creep tests to evaluate the influence of fabrics mechanical behavior on the mechanical response of the resulting composites. The morphological analysis of the fracture surface of the tensile samples showed the better fiber-matrix adhesion between PLA and jute fabric.

  3. Ferritic Alloys with Extreme Creep Resistance via Coherent Hierarchical Precipitates

    Science.gov (United States)

    Song, Gian; Sun, Zhiqian; Li, Lin; Xu, Xiandong; Rawlings, Michael; Liebscher, Christian H.; Clausen, Bjørn; Poplawsky, Jonathan; Leonard, Donovan N.; Huang, Shenyan; Teng, Zhenke; Liu, Chain T.; Asta, Mark D.; Gao, Yanfei; Dunand, David C.; Ghosh, Gautam; Chen, Mingwei; Fine, Morris E.; Liaw, Peter K.

    2015-11-01

    There have been numerous efforts to develop creep-resistant materials strengthened by incoherent particles at high temperatures and stresses in response to future energy needs for steam turbines in thermal-power plants. However, the microstructural instability of the incoherent-particle-strengthened ferritic steels limits their application to temperatures below 900 K. Here, we report a novel ferritic alloy with the excellent creep resistance enhanced by coherent hierarchical precipitates, using the integrated experimental (transmission-electron microscopy/scanning-transmission-electron microscopy, in-situ neutron diffraction, and atom-probe tomography) and theoretical (crystal-plasticity finite-element modeling) approaches. This alloy is strengthened by nano-scaled L21-Ni2TiAl (Heusler phase)-based precipitates, which themselves contain coherent nano-scaled B2 zones. These coherent hierarchical precipitates are uniformly distributed within the Fe matrix. Our hierarchical structure material exhibits the superior creep resistance at 973 K in terms of the minimal creep rate, which is four orders of magnitude lower than that of conventional ferritic steels. These results provide a new alloy-design strategy using the novel concept of hierarchical precipitates and the fundamental science for developing creep-resistant ferritic alloys. The present research will broaden the applications of ferritic alloys to higher temperatures.

  4. Low ductility creep failure in austenitic weld metals

    International Nuclear Information System (INIS)

    Thomas, R.G.

    Creep tests have been carried out for times of up to approx. 22,000 hrs on three austenitic weld metals of nominal composition 17Cr-8Ni-2Mo, 19Cr-12Ni-3Mo+Nb and 17Cr-10Ni-2Mo. The two former deposits were designed to produce delta-ferrite contents in the range 3-9% while the latter was designed to be fully austenitic. The common feature of all three weld metals was that they all gave very low strains at failure, typically approx. 1%. The microstructures of the failed creep specimens have been studied using optical and electron microscopy and the precipitate structures related to the occurrence of low creep strains. Creep deformation and fracture mechanisms in austenitic materials in general have been reviewed and this has been used as a basis for discussion of the observations of the present work. Finally, some of the factors that can be controlled to improve long-term creep ductility have been appraised

  5. Standard test method for creep-fatigue crack growth testing

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This test method covers the determination of creep-fatigue crack growth properties of nominally homogeneous materials by use of pre-cracked compact type, C(T), test specimens subjected to uniaxial cyclic forces. It concerns fatigue cycling with sufficiently long loading/unloading rates or hold-times, or both, to cause creep deformation at the crack tip and the creep deformation be responsible for enhanced crack growth per loading cycle. It is intended as a guide for creep-fatigue testing performed in support of such activities as materials research and development, mechanical design, process and quality control, product performance, and failure analysis. Therefore, this method requires testing of at least two specimens that yield overlapping crack growth rate data. The cyclic conditions responsible for creep-fatigue deformation and enhanced crack growth vary with material and with temperature for a given material. The effects of environment such as time-dependent oxidation in enhancing the crack growth ra...

  6. Cumulative creep damage for unidirectional composites under step loading

    Science.gov (United States)

    Guedes, Rui Miranda

    2012-11-01

    The creep lifetime prediction of unidirectional composite materials under step loading, based on constant loading durability diagram, is analyzed for the two-step creep loading condition. For this purpose different nonlinear cumulative-damage laws are revisited and applied to predict creep lifetime. One possible approach to accounting for damage accumulation is provided by the continuum-damage mechanics (CDM). However, the CDM lifetime expression obtained for constant loading condition presents some drawbacks. Specifically, the upper stress range is not accommodated by CDM form. A modification of CDM is proposed, forcing the CDM to capture the short-term creep failure. It is proven that this modified CDM (MCDM) does not yield the same predictions as the Linear Cumulative-damage law (Miner's law). Predictions obtained from the nonlinear cumulative-damage laws are compared against synthetic lifetime generated by a micromechanical model that simulates unidirectional composites under two-step creep loading condition. Comparable deviations from Miner's law are obtained by the nonlinear cumulative-damage laws.

  7. Recovery of creep properties of the nickel-base superalloy nimonic 105

    CSIR Research Space (South Africa)

    Girdwood, RB

    1996-01-01

    Full Text Available Uniaxial constant stress creep tests were performed on the wrought nickel-base superalloy Nimonic 105. Entire creep curves were recorded and curve shapes analysed using the Theta Projection Concept. Rejuventive procedures were applied to pre...

  8. Chapter 4. Introduction to the calculation of structures subjected to creep and relaxation

    International Nuclear Information System (INIS)

    Bahuaud, J.; Fauchon, J.; Siarras, G.

    1972-01-01

    The topics covered are: influence of time on metal behavior (tensile tests, creep, relaxation, viscoelastic models): stress-strain relationships (stresses, strains, linear elasticity, plasticity, linear viscoelasticity and creep) [fr

  9. Creep Tests and Modeling Based on Continuum Damage Mechanics for T91 and T92 Steels

    Science.gov (United States)

    Pan, J. P.; Tu, S. H.; Zhu, X. W.; Tan, L. J.; Hu, B.; Wang, Q.

    2017-12-01

    9-11%Cr ferritic steels play an important role in high-temperature and high-pressure boilers of advanced power plants. In this paper, a continuum damage mechanics (CDM)-based creep model was proposed to study the creep behavior of T91 and T92 steels at high temperatures. Long-time creep tests were performed for both steels under different conditions. The creep rupture data and creep curves obtained from creep tests were captured well by theoretical calculation based on the CDM model over a long creep time. It is shown that the developed model is able to predict creep data for the two ferritic steels accurately up to tens of thousands of hours.

  10. Effects of segregation of primary alloying elements on the creep response in magnesium alloys

    DEFF Research Database (Denmark)

    Huang, Y.D.; Dieringa, H.; Hort, N.

    2008-01-01

    The segregation of primary alloying elements deteriorates the high temperature creep resistance of magnesium alloys. Annealing at high temperatures alleviating their segregations can improve the creep resistance. Present investigation on the effect of segregation of primary alloying elements on t...

  11. Mechanical modelling of a structural performance of a pressure vessel submitted to the creep phenomenon

    International Nuclear Information System (INIS)

    Taroco, E.; Feijoo, R.A.; Monteiro, Edson; Freire, J.L.F.; Bevilacqua, L.; Miranda, P.E.V. de; Silveira, T.L. da

    1982-01-01

    A pressure vessel is analized using different mechanical models for the creep phenomenon. The numerical results obtained through these models enable us to recommend on the way verifications of creep damage accumulation is structures should be made. (Author) [pt

  12. Developing of corrosion and creep property test database system

    International Nuclear Information System (INIS)

    Park, S. J.; Jun, I.; Kim, J. S.; Ryu, W. S.

    2004-01-01

    The corrosion and creep characteristics database systems were constructed using the data produced from corrosion and creep test and designed to hold in common the data and programs of tensile, impact, fatigue characteristics database that was constructed since 2001 and others characteristics databases that will be constructed in future. We can easily get the basic data from the corrosion and creep characteristics database systems when we prepare the new experiment and can produce high quality result by compare the previous test result. The development part must be analysis and design more specific to construct the database and after that, we can offer the best quality to customers various requirements. In this thesis, we describe the procedure about analysis, design and development of the impact and fatigue characteristics database systems developed by internet method using jsp(Java Server pages) tool

  13. The effect of phosphorus on creep in copper

    International Nuclear Information System (INIS)

    Sandstroem, Rolf; Andersson, Henrik C.M.

    2008-01-01

    Pure copper with an addition of about 50 ppm phosphorus is the planned material for the outer part of the waste package for spent nuclear fuel in Sweden. Phosphorus is added to improve the creep ductility but it also strongly increases the creep strength. In the present paper the influence of phosphorus on the strength properties of copper is analysed. Using the Labusch-Nabarro model it is demonstrated that 50 ppm has a negligible influence on the yield strength in accordance with observations. For slow moving dislocations, the interaction energy between the P-atoms and the dislocations gives rise to an agglomeration and a locking. The computed break away stresses are in agreement with the difference in creep stress of copper with and without P-additions

  14. Qualification of P91 welds through Small Punch creep testing

    Energy Technology Data Exchange (ETDEWEB)

    Blagoeva, D. [Nuclear Research and Consultancy Group, Westerduinweg 3, P.O. Box 25, 1755 ZG Petten (Netherlands); Li, Y.Z. [KEMA Nederland BV, P.O. Box 9035, NL-6800 ET, Arnhem (Netherlands); Hurst, R.C., E-mail: roger.hurst@ec.europa.eu [Institute for Energy, European Commission Joint Research Centre, P.O. Box 2, 1755 ZG Petten (Netherlands)

    2011-02-15

    The deployment of the martensitic alloy P91 in future nuclear plant components operating in the creep regime depends very much on the performance of joints, found occasionally susceptible to failure in fossil fuel fired plant A completely novel approach is proposed to assess the integrity of P91 weldments which relies on the determination of the creep properties of the different zones of the weldment on a micro-scale based on the Small Punch (SP) testing methodology. Results are presented from the Small Punch creep tests carried out exactly following a CEN Code of Practice for the various constituent zones of the weldment and the potential weaknesses are identified within the heat affected zone. In addition, the SP test is applied to determine the fracture properties of the weld compared to the parent metal, showing the expected shift related to the test method in the ductile brittle transition temperature and the inferior performance of the weld metal.

  15. Microstructural Effects on Creep-Fatigue Life of Alloy 709

    Energy Technology Data Exchange (ETDEWEB)

    McMurtrey, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States); Carroll, Laura [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wright, Jill [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-08-01

    Creep-fatigue tests were performed on plates of Alloy 709 from various heats and processing conditions, but often with inhomogeneous microstructures. After testing, metallographic analysis was performed and the specimens were generally found to either have a uniform grain size or a bimodal grain size distribution with either isolated or groups (bands) of large grains. Creep-fatigue life was characterized with respect to the length of the grain boundary perpendicular to the stress axis, and it was found that large grains (>400 μm) tended to be detrimental to creep-fatigue life, with the exception of elongated (parallel to the stress axis) grains and some specimens that underwent additional annealing.

  16. Investigations on creep fatigue alternating load strength of nickel alloys

    International Nuclear Information System (INIS)

    Raule, G.

    1987-01-01

    On all three nickel based materials examined (IN 713 LC, IN 617 and Nimonic 86), the crack change numbers were considerably reduced by introducing stopping times. The cyclic stresses of the materials IN 713 LC and Nimonic 86 were not affected by the interposed stopping times. The material IN 617 is subject to considerably lower stresses with increasing stopping times than in alternate stressing without stopping times. The determination of equivalent stresses by Berling and Conway's method represents a suitable process for describing the creep fatigue behaviour of the materials examined, using creep results. This material behaviour can be assessed using the linear life proportion rule, if one takes into consideration that the resulting life constants are considerably affected by the method used to determine the time creep proportion. (orig./MM) [de

  17. Ultrasonic creeping wave test technique for dissimilar metal weld

    International Nuclear Information System (INIS)

    Yuan Jianzhong; Shang Junmin; Yan Zhi; Yuan Guanghua; Zhang Guofeng

    2009-01-01

    To solve the problem encountered in the defect inspection of the surface and near-surface of dissimilar metal weld effectively, a new ultrasonic creeping wave test technique is developed. In this paper, the test technique and its experimental verification are mainly described. The verification results show that linear defect, which is similar to the defect found in liquid penetrant test, on the surface and near-surface of dissimilar metal weld can be detected effectively, by using ultrasonic creeping wave test technique. And the depth, length and height of the defect can be determined easily. The effective covering depth of ultrasonic creeping wave test technique will reach 0-9 mm. Meanwhile, the planar defect, with equivalent area more than 3 mm 2 , existed in welds can be detected efficiently. So, accurate measurement, which self height dimension of planar defect is above 2 mm, will be realized. (authors)

  18. Salt creep and wicking counteract hydrophobic organic structures

    Science.gov (United States)

    Burkhardt, Juergen

    2017-04-01

    The hydrophobic nature of many biological and edaphic surfaces prevents wetting and water movement. Already small amounts of salts and other hygroscopic material (e.g. by aerosol deposition to leaf surfaces) may change this situation. Salts attract minute amounts of liquid water to the surface and may dynamically expand on the original surface by creeping (evaporation-driven extension of crystals). Creeping is governed by fluctuations of relative humidity and increases with time. Under high, almost saturated concentrations of the salt solutions, ions from the chaotropic side of the Hofmeister series creep most efficiently. Once established, continuous salt connections may act to channel small water flows along the surface. They may act as wicks if water is removed from one side by evaporation. Stomata may in this way become 'leaky' by the leaf surface accumulation of hygroscopic aerosols.

  19. Standard test method for creep-fatigue testing

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This test method covers the determination of mechanical properties pertaining to creep-fatigue deformation or crack formation in nominally homogeneous materials, or both by the use of test specimens subjected to uniaxial forces under isothermal conditions. It concerns fatigue testing at strain rates or with cycles involving sufficiently long hold times to be responsible for the cyclic deformation response and cycles to crack formation to be affected by creep (and oxidation). It is intended as a test method for fatigue testing performed in support of such activities as materials research and development, mechanical design, process and quality control, product performance, and failure analysis. The cyclic conditions responsible for creep-fatigue deformation and cracking vary with material and with temperature for a given material. 1.2 The use of this test method is limited to specimens and does not cover testing of full-scale components, structures, or consumer products. 1.3 This test method is primarily ...

  20. Creep of thermoplastic polyurethane reinforced with ozone functionalized carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Z. Zhang

    2012-09-01

    Full Text Available This work focused on the mechanical behavior, especially creep resistance, of thermoplastic polyurethane (TPU filled with ozone-treated multi-walled carbon nanotubes (MWCNTs. It was found that the ozone functionalization of MWCNTs could improve their dispersion and interfacial adhesion to the TPU matrix as proved by scanning electron microscope and Raman spectrometer. It finally contributed to the enhancement of Young’s modulus and yield strength of TPU/MWCNT composites. Moreover, the creep resistance and recovery of MWCNT/TPU composites revealed a significant improvement by incorporating ozone functionalized MWCNTs. The strong interaction between the modified MWCNTs and TPU matrix would enhance the interfacial bonding and facilitate the load transfer, resulting in low creep strain and unrecovered strain.

  1. Probability based high temperature engineering creep and structural fire resistance

    CERN Document Server

    Razdolsky, Leo

    2017-01-01

    This volume on structural fire resistance is for aerospace, structural, and fire prevention engineers; architects, and educators. It bridges the gap between prescriptive- and performance-based methods and simplifies very complex and comprehensive computer analyses to the point that the structural fire resistance and high temperature creep deformations will have a simple, approximate analytical expression that can be used in structural analysis and design. The book emphasizes methods of the theory of engineering creep (stress-strain diagrams) and mathematical operations quite distinct from those of solid mechanics absent high-temperature creep deformations, in particular the classical theory of elasticity and structural engineering. Dr. Razdolsky’s previous books focused on methods of computing the ultimate structural design load to the different fire scenarios. The current work is devoted to the computing of the estimated ultimate resistance of the structure taking into account the effect of high temperatur...

  2. Thermomechanical fatigue, oxidation, and Creep: Part II. Life prediction

    Science.gov (United States)

    Neu, R. W.; Sehitoglu, Huseyin

    1989-09-01

    A life prediction model is developed for crack nucleation and early crack growth based on fatigue, environment (oxidation), and creep damage. The model handles different strain-temperature phasings (i.e., in-phase and out-of-phase thermomechanical fatigue, isothermal fatigue, and others, including nonproportional phasings). Fatigue life predictions compare favorably with experiments in 1070 steel for a wide range of test conditions and strain-temperature phasings. An oxide growth (oxide damage) model is based on the repeated microrupture process of oxide observed from microscopic measurements. A creep damage expression, which is stress-based, is coupled with a unified constitutive equation. A set of interrupted tests was performed to provide valuable damage progression information. Tests were performed in air and in helium atmospheres to isolate creep damage from oxidation damage.

  3. The irradiation creep characteristics of graphite to high fluences

    International Nuclear Information System (INIS)

    Kennedy, C.R.; Cundy, M.; Kleist, G.

    1988-01-01

    High-temperature gas-cooled reactors (HTGR) have massive blocks of graphite with thermal and neutron-flux gradients causing high internal stresses. Thermal stresses are transient; however, stresses generated by differential growth due to neutron damage continue to increase with time. Fortunately, graphite also experiences creep under irradiation allowing relaxation of stresses to nominally safe levels. Because of complexity of irradiation creep experiments, data demonstrating this phenomenon are generally limited to fairly low fluences compared to the overall fluences expected in most reactors. Notable exceptions have been experiments at 300/degree/C and 500/degree/C run at Petten under tension and compression creep stresses to fluences greater than 4 /times/ 10 26 (E > 50 keV) neutrons/m 2 . This study complements the previous results by extending the irradiation temperature to 900/degree/C. 2 refs., 3 figs

  4. MICROSTRUCTURAL STABILITY OF Ti-46Al-8Ta DURING CREEP

    Directory of Open Access Journals (Sweden)

    Hana Staneková

    2011-05-01

    Full Text Available The effect of long-term creep exposure on the microstructure stability of a new cast air-hardenable intermetallic alloy with nominal chemical composition Ti-46Al-8Ta (at .% was studied. Constat load creep test were performed at the temperature 750°C and at applied stress 250 MPa up to 3479,3 h. The initial gama(TiAl + alpha2(Ti3Al microstructure of the alloy is unstable and transforms to alpha2 + gama + tau type. During creep the formation of cavities along the lamellar colony and grain boundaries is observed. The specimens fail by the growth and coalescence of such cavities with intergranular type of fracture.

  5. Physical-Mechanism Exploration of the Low-Cycle Unified Creep-Fatigue Formulation

    OpenAIRE

    Dan Liu; Dirk John Pons

    2017-01-01

    Background—Creep-fatigue behavior is identified as the incorporated effects of fatigue and creep. One class of constitutive-based models attempts to evaluate creep and fatigue separately, but the interaction of fatigue and creep is neglected. Other models treat the damage as a single component, but the complex numerical structures that result are inconvenient for engineering application. The models derived through a curve-fitting method avoid these problems. However, the method of curving fit...

  6. Modification and Performance Evaluation of a Low Cost Electro-Mechanically Operated Creep Testing Machine

    OpenAIRE

    John J. MOMOH; Lanre Y. SHUAIB-BABATA; Gabriel O. ADELEGAN

    2010-01-01

    Existing mechanically operated tensile and creep testing machine was modified to a low cost, electro-mechanically operated creep testing machine capable of determining the creep properties of aluminum, lead and thermoplastic materials as a function of applied stress, time and temperature. The modification of the testing machine was necessitated by having an electro-mechanically operated creep testing machine as a demonstration model ideal for use and laboratory demonstrations, which will prov...

  7. Creep and damage in shells of revolution under cyclic loading and heating

    OpenAIRE

    Breslavsky, D.; Morachkovsky, O.; Tatarinova, O.

    2014-01-01

    Creep of cyclically loaded thin shells of revolution and their fracture due to creep and fatigue mechanisms are studied. Creep-damage equations for steels and nickel-based alloys are built by the use of scalar damage parameter. Constitutive equations were derived using the method of asymptotic expansions and averaging over a period of cyclic loading. The cases of fast and slow varying of temperature and loading are regarded. General problem statement and method for solution of creep problems ...

  8. Creep of SiC Hot-Pressed with Al, B, and C

    Energy Technology Data Exchange (ETDEWEB)

    Sixta, Mark Eldon [Univ. of California, Berkeley, CA (United States)

    2000-03-31

    The creep of a high strength, high toughness SiC, sintered with Al, B, and C was investigated. For elevated temperature applications, the time-dependent deformation, creep response, must be fully characterized for candidate materials. The mechanisms responsible for high temperature deformation in ABC-SiC were evaluated. The creep response was compared to materials that have glassy grain boundary phases but do not have interlocked grains. The creep mechanisms were assessed.

  9. Mechanical behaviour of cyclic olefin copolymer/exfoliated graphite nanoplatelets nanocomposites foamed through supercritical carbon dioxide

    Directory of Open Access Journals (Sweden)

    A. Biani

    2016-12-01

    Full Text Available A cycloolefin copolymer matrix was melt mixed with exfoliated graphite nanoplatelets (xGnP and the resulting nanocomposites were foamed by supercritical carbon dioxide. The density of the obtained foams decreased with the foaming pressure. Moreover, xGnP limited the cell growth during the expansion process thus reducing the cell diameter (from 1.08 to 0.22 mm with an XGnP amount of 10 wt% at 150 bar and increasing the cell density (from 12 to 45 cells/mm2 with a nanofiller content of 10 wt% at 150 bar. Electron microscopy observations of foams evidenced exfoliation and orientation of the nanoplatelets along the cell walls. Quasi-static compressive tests and tensile creep tests on foams clearly indicated that xGnP improved the modulus (up to a factor of 10 for a xGnP content of 10 wt% and the creep stability.

  10. Uranium dioxide preparation

    International Nuclear Information System (INIS)

    Watt, G.W.; Baugh, D.W. Jr.

    1977-01-01

    An actinide dioxide, e.g., uranium dioxide, is prepared by reacting an actinide nitrate or hydrate or tetrahydrofuranate thereof, e.g., uranyl nitrate, a hydrate of uranyl nitrate, or a tetrahydrofuranate of uranyl nitrate with an alkali or alkaline earth metal adduct of a monocyclic or polycyclic hydrocarbon in the presence of an inert organic solvent. Typically, the starting material may be uranyl nitrate dihydrate or uranyl nitrate ditetrahydrofuranate (the latter material is a novel composition of matter) with a reactant such as the sodium adduct of naphthalene in the presence of a solvent such as tetrahydrofuran. The resultant uranium dioxide may be further purified by heating it in the presence of hydrogen. 15 claims

  11. On the development of creep damage constitutive equations: modified hyperbolic sine law for minimum creep strain rate and stress and creep fracture criterion based on cavity area fraction along grain\\ud boundary

    OpenAIRE

    Xu, Qiang; Yang, Xin; Lu, Zhongyu

    2017-01-01

    Abstract: This paper reports 1) the latest development and application of modified hyperbolic sine law for minimum creep strain rate and stress for both low Cr and high Cr steels, and 2) the development of creep fracture criterion based on cavity area fraction along grain boundary for high Cr steel. This work is part of the fundamental development of creep damage constitutive equations which were identified through a critical literature review.\\ud In the former the application of the new law ...

  12. Carbon dioxide and climate

    International Nuclear Information System (INIS)

    1991-10-01

    Global climate change is a serious environmental concern, and the US has developed ''An Action Agenda'' to deal with it. At the heart of the US effort is the US Global Change Research Program (USGCRP), which has been developed by the Committee on Earth and Environmental Sciences (CEES) of the Federal Coordinating Council for Sciences, Engineering, and Technology (FCCSET). The USGCRP will provide the scientific basis for sound policy making on the climate-change issue. The DOE contribution to the USGCRP is the Carbon Dioxide Research Program, which now places particular emphasis on the rapid improvement of the capability to predict global and regional climate change. DOE's Carbon Dioxide Research Program has been addressing the carbon dioxide-climate change connection for more than twelve years and has provided a solid scientific foundation for the USGCRP. The expansion of the DOE effort reflects the increased attention that the Department has placed on the issue and is reflected in the National Energy Strategy (NES) that was released in 1991. This Program Summary describes projects funded by the Carbon Dioxide Research Program during FY 1991 and gives a brief overview of objectives, organization, and accomplishments. The Environmental Sciences Division of the Office of Health and Environmental Research, Office of Energy Research supports a Carbon Dioxide Research Program to determine the scientific linkage between the rise of greenhouse gases in the atmosphere, especially carbon dioxide, and climate and vegetation change. One facet is the Core CO 2 Program, a pioneering program that DOE established more than 10 years ago to understand and predict the ways that fossil-fuel burning could affect atmospheric CO 2 concentration, global climate, and the Earth's biosphere. Major research areas are: global carbon cycle; climate detection and models of climate change; vegetation research; resource analysis; and, information and integration

  13. Grain size, stress and creep in polycrystalline solids

    CSIR Research Space (South Africa)

    Nabarro, FRN

    2000-08-01

    Full Text Available creep. Fig. 3. Diagram for aluminum augmented by the line w(s ) determining the dislocation cell size. Where w < L, power- law breakdown occurs at a stress independent of grain size. PHYSICS OF THE SOLID STATE Vol. 42 No. 8 2000 GRAIN SIZE...-7834/00/4208- $20.00 ? 2000 MAIK ?Nauka/Interperiodica? Physics of the Solid State, Vol. 42, No. 8, 2000, pp. 1456?1459. From Fizika Tverdogo Tela, Vol. 42, No. 8, 2000, pp. 1417?1419. Original English Text Copyright ? 2000 by Nabarro. 1. DIFFUSIONAL CREEP...

  14. Creep Behaviour of Fly Ash-Based Geopolymer Concrete

    OpenAIRE

    Wallah S.E.

    2010-01-01

    Fly ash-based geopolymer concrete is manufactured using fly ash as its source material and does not use Portland cement at all. Beside fly ash, alkaline solution is also utilized to make geopolymer paste which binds the aggregates to form geopolymer concrete. This paper presents the study of creep behaviour of fly ash-based geopolymer concrete. Four series of specimens with various compressive strengths were prepared to study its creep behaviour for the duration of test up to one year. The te...

  15. In pile creep measuring rigs for metallic specimens

    International Nuclear Information System (INIS)

    Masson, M.

    1976-01-01

    Two types of creep rigs are described using stainless steel or zircaloy specimens. First, a tensile creep rig allowing continuous length measurement of tubular or solid specimens. The measurement of the specimen length is compared with that of a reference specimen, situated as close as possible to the tensile one. The second rig is used for continuous measurement of the radial strain of pressurised tubes. The measurement is made by a cone and ball system, transforming diameter changes into axial displacements. These rigs are made in two parts: a capsule with NaK, including: specimens, loading bellows microwave measuring system, and a standard 'CHOUCA' furnace with electrical heating [fr

  16. Irradiation creep of the mixed oxide UPuO2

    International Nuclear Information System (INIS)

    Combette, Patrick; Milet, Claude

    1976-01-01

    The irradiation creep under compression of the mixed oxide UO 2 -PuO 2 was studied up to fission yields of 6x10 13 fcm -3 s -1 , under stresses -2 , in the temperature range 700-900 deg C. The creep rate is proportional to the applied stress and fission yield, athermal in the studied temperature range and non-dependent of burnup (up to 30000MWjt -1 ). In a sample under compression, swelling is observed due to the formation of fission products during the irradiation and the swelling rate is of the same order that in a cladded fuel element [fr

  17. Digital signal processing of data from borehole creep closure

    International Nuclear Information System (INIS)

    Chakrabarti, S.; Patrick, W.C.; Duplancic, N.

    1987-01-01

    Digital signal processing, a technique commonly used in the fields of electrical engineering and communication technology, has been successfully used to analyze creep closure data obtained from a 0.91 m diameter by 5.13 deep borehole in bedded salt. By filtering the ''noise'' component of the closure data from a test borehole, important data trends were made more evident and average creep closure rates were able to be calculated. This process provided accurate estimates of closure rates that are used in the design of lined boreholes in which heat-generating transuranic nuclear wastes are emplaced at the Waste Isolation Pilot Plant

  18. Multiaxial creep-fatigue life analysis using strainrange partitioning

    International Nuclear Information System (INIS)

    Manson, S.S.; Halford, G.R.

    1976-01-01

    Strain-Range Partitioning is a recently developed method for treating creep-fatigue interaction at elevated temperature. Most of the work to date has been on uniaxially loaded specimens, whereas practical applications often involve load multiaxiality. This paper shows how the method can be extended to treat multiaxiality through a set of rules for combining the strain components in the three principal directions. Closed hysteresis loops, as well as plastic and creep strain ratcheting, are included. An application to hold-time tests in torsion is used to illustrate the approach

  19. Oxidation resistant high creep strength austenitic stainless steel

    Science.gov (United States)

    Brady, Michael P.; Pint, Bruce A.; Liu, Chain-Tsuan; Maziasz, Philip J.; Yamamoto, Yukinori; Lu, Zhao P.

    2010-06-29

    An austenitic stainless steel displaying high temperature oxidation and creep resistance has a composition that includes in weight percent 15 to 21 Ni, 10 to 15 Cr, 2 to 3.5 Al, 0.1 to 1 Nb, and 0.05 to 0.15 C, and that is free of or has very low levels of N, Ti and V. The alloy forms an external continuous alumina protective scale to provide a high oxidation resistance at temperatures of 700 to 800.degree. C. and forms NbC nanocarbides and a stable essentially single phase fcc austenitic matrix microstructure to give high strength and high creep resistance at these temperatures.

  20. Brittle Creep Failure, Critical Behavior, and Time-to-Failure Prediction of Concrete under Uniaxial Compression

    Directory of Open Access Journals (Sweden)

    Yingchong Wang

    2015-01-01

    Full Text Available Understanding the time-dependent brittle deformation behavior of concrete as a main building material is fundamental for the lifetime prediction and engineering design. Herein, we present the experimental measures of brittle creep failure, critical behavior, and the dependence of time-to-failure, on the secondary creep rate of concrete under sustained uniaxial compression. A complete evolution process of creep failure is achieved. Three typical creep stages are observed, including the primary (decelerating, secondary (steady state creep regime, and tertiary creep (accelerating creep stages. The time-to-failure shows sample-specificity although all samples exhibit a similar creep process. All specimens exhibit a critical power-law behavior with an exponent of −0.51 ± 0.06, approximately equal to the theoretical value of −1/2. All samples have a long-term secondary stage characterized by a constant strain rate that dominates the lifetime of a sample. The average creep rate expressed by the total creep strain over the lifetime (tf-t0 for each specimen shows a power-law dependence on the secondary creep rate with an exponent of −1. This could provide a clue to the prediction of the time-to-failure of concrete, based on the monitoring of the creep behavior at the steady stage.

  1. Modelling creep of pressure vessels with thermal gradients using Theta projection data

    International Nuclear Information System (INIS)

    Law, M.; Payten, W.; Snowden, K.

    2002-01-01

    Pressure vessels are often exposed to through-wall temperature gradients. Thermal stresses occur in addition to pressure stresses. The resulting creep response is calculated using the Theta projection creep algorithm within a finite element code. It was found that the stress and temperature dependence of the creep response may lead to complex stress evolution

  2. Creep Behavior of Porous Supports in Metal-support Solid Oxide Fuel Cells

    DEFF Research Database (Denmark)

    Boccaccini, Dino; Frandsen, Henrik Lund; Blennow Tullmar, Peter

    2013-01-01

    metal supports, where high corrosion resistance is a major design requirement. The four variables affecting creep rate are strain, time, temperature, and stress level and make creep difficult to quantify. In this work, the creep parameters of a SOFC metal support have been determined for the first time...

  3. Consideration on evaluation of internal pressure creep rupture for tube with circumferential joint

    International Nuclear Information System (INIS)

    Nagato, Kotaro; Satoh, Keisuke

    1983-01-01

    The behavior of internal pressure creep rupture of the thin-walled cylinders with circumferential joints is affected by the combination of creep characteristics of parent materials and weld metals. In particular, the compatibility of the creep strain rate of parent materials and weld metals becomes an important controlling factor. The behavior of internal pressure creep of the welded parts in circumferential joint cylinders can be evaluated simply with the uniaxial creep data of parent materials and weld metals, considering it by approximately substituting with the creep behavior of a uniaxial longitudinal joint. The method of evaluation is, first, to analyze the breaking behavior of uniaxial longitudinal joints using the uniaxial creep characteristic values of parent materials and weld metals, and next, by combining the equation for the relation between the rupture times of uniaxial creep and internal pressure creep with the analyzed breaking behavior of uniaxial joints, the internal pressure creep rupture behavior of the cylinders with circumferential joints can be evaluated. The internal pressure creep behavior of the thin-walled cylinders with circumferential joints, their rupture life and the uniaxial creep rupture life of longitudinal joints, and the examination of Hastelloy X cylinders are reported. (Kako, I.)

  4. Deformation Microstructures and Creep Mechanisms in Advanced ZR-Based Cladding Under Biazal Loading

    Energy Technology Data Exchange (ETDEWEB)

    K. Linga (KL) Murty

    2008-08-11

    Investigate creep behavior of Zr-based cladding tubes with attention to basic creep mechanisms and transitions in them at low stresses and/or temperatures and study the dislocation microstructures of deformed samples for correlation with the underlying micromechanism of creep

  5. A fractional derivative approach to full creep regions in salt rock

    Science.gov (United States)

    Zhou, H. W.; Wang, C. P.; Mishnaevsky, L.; Duan, Z. Q.; Ding, J. Y.

    2013-08-01

    Based on the definition of the constant-viscosity Abel dashpot, a new creep element, referred to as the variable-viscosity Abel dashpot, is proposed to characterize damage growth in salt rock samples during creep tests. Ultrasonic testing is employed to determine a formula of the variable viscosity coefficient, indicating that the change of the variable viscosity coefficient with the time meets a negative exponent law. In addition, by replacing the Newtonian dashpot in the classical Nishihara model with the variable-viscosity Abel dashpot, a damage-mechanism-based creep constitutive model is proposed on the basis of time-based fractional derivative. The analytic solution for the fractional-derivative creep constitutive model is presented. The parameters of the fractional derivative creep model are determined by the Levenberg-Marquardt method on the basis of the experimental results of creep tests on salt rock. Furthermore, a sensitivity study is carried out, showing the effects of stress level, fractional derivative order and viscosity coefficient exponent on creep strain of salt rock. It is indicated that the fractional derivative creep model proposed in the paper provides a precise description of full creep regions in salt rock, i.e., the transient creep region (the primary region), the steady-state creep region (the secondary region) and the accelerated creep region (the tertiary region).

  6. Treatment of effluent at the Saclay Centre d'Etudes Nucleaires (1960); Le traitement des effluents du Centre d'Etudes Nucleaires de Saclay (1960)

    Energy Technology Data Exchange (ETDEWEB)

    Wormser, G. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The Centre d'Etudes Nucleaires at Saclay possesses several installations from which liquid radioactive effluent is rejected, and it has thus been found necessary to construct a station for the purification of radioactive liquids and to settle various chemical, analytical and technological problems. This report describes, in the following order: - the disposal possibilities at the Centre d'Etudes Nucleaires, Saclay, - the effluents produced at the centre, - the set-up for collecting effluent, - treatment of the effluent, - results of these treatments. (author) [French] La presence, au Centre d'Etudes Nucleaires de Saclay, de plusieurs installations susceptibles de rejeter des effluents liquides radioactifs a necessite la construction d'une station d'epuration d'eaux radioactives et la mise au point de differents problemes chimiques, analytiques et technologiques. Dans ce rapport, nous exposerons successivement: - les possibilites de rejet du Centre d'Etudes Nucleaires de Saclay, - les effluents du centre, - le dispositif de collecte des effluents, - le traitement de ces effluents, - les resultats de ces traitements. (auteur)

  7. Sequential creep-fatigue interaction in austenitic stainless steel type 316L-SPH

    International Nuclear Information System (INIS)

    Tavassoli, A.A.; Mottot, M.; Petrequin, P.

    1986-01-01

    Influence of a prior creep or fatigue exposure on subsequent fatigue or creep properties of stainless steel type 316 L SPH has been investigated. The results obtained are used to verify the validity of time and cycle fraction rule and to obtain information on the effect of very long intermittent hold times on low cycle fatigue properties, as well as on transitory loads occurring during normal service of some structural components of LMFBR reactors. Creep and fatigue tests have been carried out at 600 0 C and under conditions yielding equal or different fatigue saturation and creep stresses. Prior creep damage levels introduced range from primary to tertiary creep, whilst those of fatigue span from 20 to 70 percent of fatigue life. In both creep-fatigue and fatigue-creep sequences in the absence of a permanent prior damage (cavitation or cracking) the subsequent resistance of 316 L-SPH to fatigue or creep is unchanged, if not improved. Thin foils prepared from the specimens confirmed these observations and showed that the dislocation substructure developed during the first mode of testing is quickly replaced by that of the second mode. Grain boundary cavitation does not occur in 316 L-SPH during creep exposures to well beyond the apparent end of secondary stage and as a result prior creep exposures up to approximately 80% of rupture life do not affect fatigue properties. Conversely, significant surface cracks were found in the prior fatigue tested specimens after above about 50% life. In the presence of such cracks the subsequent creep damage was localized at the tip of the main crack and the remaining creep life was found to be usually proportional to the effective specimen cross section. Creep and fatigue sequential damage are not necessarily additive and this type of loadings are in general less severe than the repeated creep-fatigue cycling. 17 refs.

  8. Creep and creep rupture of laminated graphite/epoxy composites. Ph.D. Thesis. Final Report, 1 Oct. 1979 - 30 Sep. 1980

    Science.gov (United States)

    Dillard, D. A.; Morris, D. H.; Brinson, H. F.

    1981-01-01

    An incremental numerical procedure based on lamination theory is developed to predict creep and creep rupture of general laminates. Existing unidirectional creep compliance and delayed failure data is used to develop analytical models for lamina response. The compliance model is based on a procedure proposed by Findley which incorporates the power law for creep into a nonlinear constitutive relationship. The matrix octahedral shear stress is assumed to control the stress interaction effect. A modified superposition principle is used to account for the varying stress level effect on the creep strain. The lamina failure model is based on a modification of the Tsai-Hill theory which includes the time dependent creep rupture strength. A linear cumulative damage law is used to monitor the remaining lifetime in each ply.

  9. Estimation method on flexural creep fracture strength of satin woven CFRP laminates. Shusuori CFRP sekisoban no mage creep hakai jumyo no yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Miyano, Y.; Hattori, Y. (Kanazawa Institute of Technology, Ishikawa (Japan). Materials System Research Laboratory); Kasamori, M. (Industrial Research Institute of Ishikawa, Ishikawa (Japan)); Otsuka, T. (Kanazawa Institute of Technology, Ishikawa (Japan))

    1992-11-15

    When machines and equipment using CFRP composites as structural material are designed, precise and quick estimation of the creep behavior for a long time is required. This paper is concerned with the prediction of flexural creep fracture for CFRP laminates consisting of satin woven carbon fibers and high temperature epoxy matrix. The flexural creep tests for CFRP were practically carried out under various stress levels at 50 centigrade to be sufficiently lower than its glass transition temperature (236 centigrade). On the other hand, the static flexural tests were carried out under various deflection rates and temperatures. The master curve of flexural strength of CFRP was obtained by applying the reciprocation law between time and temperature to these experimental results. Furthermore, the flexural creep fracture of CFRP was estimated by utilizing the linear cumulative damage rule adapted to this master curve. The creep fracture predicted by the method mentioned above is fairly well agreed with that measured by creep tests. 10 refs., 8 figs.

  10. Carbon dioxide recycling

    Science.gov (United States)

    The recycling of carbon dioxide to methanol and dimethyl ether is seen to offer a substantial route to renewable and environmentally carbon neutral fuels. One of the authors has championed the “Methanol Economy" in articles and a book. By recycling ambient CO2, the authors argue ...

  11. Bench Remarks: Carbon Dioxide.

    Science.gov (United States)

    Bent, Henry A.

    1987-01-01

    Discusses the properties of carbon dioxide in its solid "dry ice" stage. Suggests several demonstrations and experiments that use dry ice to illustrate Avogadro's Law, Boyle's Law, Kinetic-Molecular Theory, and the effects of dry ice in basic solution, in limewater, and in acetone. (TW)

  12. Balancing atmospheric carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Goreau, T.J. (Discovery Bay Marine Laboratory, Univ. of the West Indies (JM))

    1990-01-01

    Rising carbon dioxide and global temperatures are causing increasing worldwide concern, and pressure towards an international law of the atmosphere is rapidly escalating, yet widespread misconceptions about the greenhouse effect's inevitability, time scale, and causes have inhibited effective consensus and action. Observations from Antarctic ice cores, Amazonian rain forests, and Carribean coral reefs suggest that the biological effects of climate change may be more severe than climate models predict. Efforts to limit emissions from fossil-fuel combustion alone are incapable of stabilizing levels of carbon dioxide in the atmosphere. Stabilizing atmospheric carbon dioxide requires coupled measures to balance sources and sinks of the gas, and will only be viable with large-scale investments in increased sustainable productivity on degraded tropical soils, and in long-term research on renewable energy and biomass product development in the developing countries. A mechanism is outlined which directly links fossil-fuel combustion sources of carbon dioxide to removal via increasing biotic productivity and storage. A preliminary cost-benefit analysis suggests that such measures are very affordable, costing far less than inaction. (With 88 refs.).

  13. Investigation on mechanical properties and creep behavior of stir cast AZ91-SiCp composites

    Directory of Open Access Journals (Sweden)

    Abhilash Viswanath

    2015-03-01

    Full Text Available The room temperature mechanical properties and high temperature creep behavior of AZ91 alloy reinforced with SiCp synthesized via stir casting have been evaluated. The mechanical properties showed improvement with respect to the amount of reinforcement content. The creep testing of the composites carried out at a temperature of 175 °C under constant stress of 80, 100 and 120 MPa reveals different creep characteristics depending upon the reinforcement content and the applied load. The true stress exponents of different composites calculated from minimum creep rate indicate the possible mechanisms of creep deformation.

  14. Low-Temperature Fault Creep: Strong vs. Weak, Steady vs. Episodic

    Science.gov (United States)

    Wang, K.; Gao, X.

    2017-12-01

    Unless we understand how faults creep, we do not fully understand how they produce earthquakes. However, most of the physics and geology of low-temperature creep is not known. There are two end-member types of low-temperature creep: weak creep of smooth faults and strong creep of rough faults, with a spectrum of intermediate modes in between. Most conceptual and numerical models deal with weak creep, assuming a very smooth fault with a gouge typically weakened by hydrous minerals (Harris, 2017). Less understood is strong creep. For subduction zones, strong creep appears to be common and is often associated with the subduction of large geometrical irregularities such as seamounts and aseismic ridges (Wang and Bilek, 2014). These irregularities generate fracture systems as they push against the resistance of brittle rocks. The resultant heterogeneous stress and structural environment makes it very difficult to lock the fault. The geodetically observed creep under such conditions is accomplished by the complex deformation of a 3D damage zone. Strong-creeping faults dissipate more heat than faults that produce great earthquakes (Gao and Wang, 2014). Although an integrated frictional strength of the fault is still a useful concept, the creeping mechanism is very different from frictional slip of a velocity-strengthening smooth fault. Cataclasis and pressure-solution creep in the fracture systems must be important processes in strong creep. Strong creep is necessarily non-steady and produces small and medium earthquakes. Strong creep of a megathrust can also promote the occurrence of a very special type of weak creep - episodic slow slip around the mantle wedge corner accompanied with tremor (ETS). An example is Hikurangi, where strong creep causes the frictional-viscous transition along the plate interface to occur much shallower than the mantle wedge corner, a necessary condition for ETS (Gao and Wang, 2017). Gao and Wang (2014), Strength of stick-slip and creeping

  15. High-temperature creep properties and life predictions for T91 and T92 steels

    Science.gov (United States)

    Pan, J. P.; Tu, S. H.; Sun, G. L.; Zhu, X. W.; Tan, L. J.; Hu, B.

    2018-01-01

    9-11%Cr heat-resistant steels are widely used in high-temperature and high-pressure boilers of advanced power plants. In the current paper, high-temperature creep behaviors of T91 and T92 steels have been investigated. Creep tests were performed for both steels at varied temperatures. The creep mechanisms of T91 and T92 steels were elucidated by analyzing the creep rupture data of the two steels. In addition, Manson-Haferd model was employed to predict the creep life of T91 and T92 steels, the results of which indicate that the Manson-Haferd model works well for the two steels.

  16. Creep buckling: an experiment, an 'exact' solution and some simple thoughts

    International Nuclear Information System (INIS)

    Heller, P.; Anderson, R.G.

    1986-01-01

    The paper presents attempts to analyse and understand a carefully conducted creep buckling experiment. The analysis was conducted using the ABAQUS Finite Element Code coupled to a number of plausible creep laws. The results show good agreement between ABAQUS runs and experimental deflections but it is difficult to reproduce the early loads. A simple model of buckling analysis for n-power creep laws is derived as an aid to understanding the development of the deflections for non-linear creep laws. In particular, the model suggests why deflections develop so rapidly and how the creep deflection development relates to the elastic behaviour. (author)

  17. Creep compliance rheology with a probe-like cylindrical geometry.

    Science.gov (United States)

    Connelly, Kelly; Sharif-Kashani, Pooria; Farajzadeh, Matt; Hubschman, Jean-Pierre; Kavehpour, H Pirouz

    2016-01-01

    Rheology experiments have been performed on the vitreous humor, a soft gel that rests inside of the eye, to study its viscoelastic behavior and underlying macromolecular structure. A significant challenge for experimentalists is preserving the macromolecular structure when removing vitreous from in vivo conditions. We have developed a novel probe-like rheometer geometry that allows us to perform shear rheology experiments on the vitreous humor in situ. The aim of this study is to assess the feasibility of the probe geometry. Creep compliance responses of silicone oils, Xanthan gum solutions, and bovine and porcine vitreous humor were measured using the probe geometry and compared to measurements performed with standard geometries. Viscosities calculated from the creep responses of silicone oils closely match between the probe and standard geometry. Viscosities and creep compliance values of Xanthan gum measurements achieve order of magnitude agreement between the probe and standard geometry. Significant differences are detected with the probe between bovine and porcine vitreous (p<0.001). These results suggest the probe may feasibly measure viscosities of Newtonian fluids, and correctly detect differences in the creep response of complex fluids with varying viscoelastic behaviors.

  18. Physical simulations of cavity closure in a creeping material

    Energy Technology Data Exchange (ETDEWEB)

    Sutherland, H.J.; Preece, D.S.

    1985-09-01

    The finite element method has been used extensively to predict the creep closure of underground petroleum storage cavities in rock salt. Even though the numerical modeling requires many simplifying assumptions, the predictions have generally correlated with field data from instrumented wellheads, however, the field data are rather limited. To gain an insight into the behavior of three-dimensional arrays of cavities and to obtain a larger data base for the verification of analytical simulations of creep closure, a series of six centrifuge simulation experiments were performed using a cylindrical block of modeling clay, a creeping material. Three of the simulations were conducted with single, centerline cavities, and three were conducted with a symmetric array of three cavities surrounding a central cavity. The models were subjected to body force loading using a centrifuge. For the single cavity experiments, the models were tested at accelerations of 100, 125 and 150 g's for 2 hours. For the multi-cavity experiments, the simulations were conducted at 100 g's for 3.25 hours. The results are analyzed using dimensional analyses. The analyses illustrate that the centrifuge simulations yield self-consistent simulations of the creep closure of fluid-filled cavities and that the interaction of three-dimensional cavity layouts can be investigated using this technique.

  19. Creeping Viscous Flow around a Heat-Generating Solid Sphere

    DEFF Research Database (Denmark)

    Krenk, Steen

    1981-01-01

    The velocity field for creeping viscous flow around a solid sphere due to a spherically symmetric thermal field is determined and a simple thermal generalization of Stokes' formula is obtained. The velocity field due to an instantaneous heat source at the center of the sphere is obtained in close...... form and an application to the storage of heat-generating nuclear waste is discussed....

  20. Creep in directionally solidified NiAl-Mo eutectics

    Czech Academy of Sciences Publication Activity Database

    Dudová, Marie; Kuchařová, Květa; Barták, Tomáš; Bei, H.; George, E.P.; Somsen, Ch.; Dlouhý, Antonín

    2011-01-01

    Roč. 65, č. 8 (2011), s. 699-702 ISSN 1359-6462 R&D Projects: GA ČR GA202/09/2073 Institutional research plan: CEZ:AV0Z20410507 Keywords : high - temperature creep * NiAl - Mo eutectic * Mo fibres Subject RIV: JG - Metallurgy Impact factor: 2.699, year: 2011

  1. Intermittent flow under constant forcing: Acoustic emission from creep avalanches

    Science.gov (United States)

    Salje, Ekhard K. H.; Liu, Hanlong; Jin, Linsen; Jiang, Deyi; Xiao, Yang; Jiang, Xiang

    2018-01-01

    While avalanches in field driven ferroic systems (e.g., Barkhausen noise), domain switching of martensitic nanostructures, and the collapse of porous materials are well documented, creep avalanches (avalanches under constant forcing) were never observed. Collapse avalanches generate particularly large acoustic emission (AE) signals and were hence chosen to investigate crackling noise under creep conditions. Piezoelectric SiO2 has a strong piezoelectric response even at the nanoscale so that we chose weakly bound SiO2 spheres in natural sandstone as a representative for the study of avalanches under time-independent, constant force. We found highly non-stationary crackling noise with four activity periods, each with power law distributed AE emission. Only the period before the final collapse shows the mean field behavior (ɛ near 1.39), in agreement with previous dynamic measurements at a constant stress rate. All earlier event periods show collapse with larger exponents (ɛ = 1.65). The waiting time exponents are classic with τ near 2.2 and 1.32. Creep data generate power law mixing with "effective" exponents for the full dataset with combinations of mean field and non-mean field regimes. We find close agreement with the predicted time-dependent fiber bound simulations, including events and waiting time distributions. Båth's law holds under creep conditions.

  2. Comparing creep in two stainless steels AISI 316

    International Nuclear Information System (INIS)

    Silveira, T.L. da; Monteiro, S.N.

    1976-07-01

    Two AISI 316 stainless steels, one of Brazilian fabrication (Villares), the other of foreign fabrication (Uddeholm) were submitted to creep tests with temperature ranging from 600 to 800 0 C. Some important differences in the mechanical behaviour of the two steels are pointed out. These differences are due to the particular thermomechanical history of the materials under consideration. (Author) [pt

  3. The Effect of Polymer Pipe Weld Geometry on Creep Lifetime

    Czech Academy of Sciences Publication Activity Database

    Ševčík, Martin; Knésl, Zdeněk; Hutař, Pavel; Náhlík, Luboš

    2011-01-01

    Roč. 465, - (2011), s. 175-178 ISSN 1013-9826 R&D Projects: GA ČR GC101/09/J027 Institutional research plan: CEZ:AV0Z20410507 Keywords : creep * stress concentration factor * lifetime * triaxiality Subject RIV: JL - Materials Fatigue, Friction Mechanics

  4. Production response of lambs receiving creep feed while grazing ...

    African Journals Online (AJOL)

    The aim of the study was to determine the production responses of lambs receiving either creep feed or not while grazing two different pastures. The production of ewes within each treatment was also recorded. The study was conducted at both the Kromme Rhee and Langgewens Research Farms. At Kromme Rhee, sheep ...

  5. Microstructural modelling of creep crack growth from a blunted crack

    NARCIS (Netherlands)

    Onck, P.R.; Giessen, E. van der

    1998-01-01

    The effect of crack tip blunting on the initial stages of creep crack growth is investigated by means of a planar microstructural model in which grains are represented discretely. The actual linking-up process of discrete microcracks with the macroscopic crack is simulated, with full account of the

  6. Creep analysis of boiler tubes by fem | Taye | Zede Journal

    African Journals Online (AJOL)

    In this paper an analysis is developed for the determination of creep deformation of an axisymmetric boiler tubes subjected to axisymmetric loads. The stresses and the permanent strains at a particular time and at the steady state condition, resulting from loading of the tube under constant internal pressure and elevated ...

  7. Shear heating in creeping faults changes the onset of convection

    Science.gov (United States)

    Tung, R.; Poulet, T.; Alevizos, S.; Veveakis, E.; Regenauer-Lieb, K.

    2017-10-01

    The interaction between mechanical deformation of creeping faults and fluid flow in porous media has an important influence on the heat and mass transfer processes in Earth sciences. Creeping faults can act as heat sources due to the effect of shear heating and as such could be expected to alter the conditions for hydrothermal convection. In this work, we provide a finite element-based numerical framework developed to resolve the problem of heat and mass transfer in the presence of creeping faults. This framework extends the analytical approach of the linear stability analysis (LSA) frequently used to determine the bifurcation criterion for onset of convection, allowing us to study compressible cases with the option of complex geometry and/or material inhomogeneities. We demonstrate the impact of creeping faults on the onset of convection and show that shear heating—expressed through its dimensionless group the Gruntfest number Gr—has exponential influence on the critical value of the Lewis number Le (inversely proportional to the Rayleigh number Ra) required for convection: Lec ˜ Lec0 eGr. In this expression, Lec0 is the critical value of Le in the absence of shear heating. This exponential scaling shows that shear heating increases the critical Lewis number and triggers hydrothermal convection at lower permeability than in situations without it. We also show that the effect of shear heating in a fault significantly alters the pattern of convection in and around the fault zone.

  8. Tension and Compression Creep Apparatus for wood-Plastic Composites

    Science.gov (United States)

    Scott E. Hamel; John C. Hermanson; Steven M. Cramer

    2011-01-01

    Design of structural members made of wood-plastic composites (WPC) is not possible without accurate test data for tension and compression. The viscoelastic behavior of these materials means that these data are required for both the quasi-static stress-strain response, and the long-term creep response. Their relative incompressibility causes inherent difficulties in...

  9. Evaluation of creep damage in power plant applications

    Energy Technology Data Exchange (ETDEWEB)

    Auerkari, P.; Salonen, J. [VTT Manufacturing Technology, Espoo (Finland)] McNiven, U. [IVO Generation Services Ltd., Naantali (Finland)] Roennberg, J. [Imatran Voima Oy, Vantaa (Finland)] Borggreen, K. [FORCE Institute, Broendby (Germany)

    1997-12-31

    Metallographic inspection of creep cavitation damage provides routine support for maintenance scheduling of high temperature components in power plants. The available European inspection experience has been reviewed, particularly considering the performance of thick-section steam systems outside the boiler. Applications are highlighted with examples from plant. (orig.) 8 refs.

  10. Damage of multilayer polymer materials under creep loading

    Czech Academy of Sciences Publication Activity Database

    Zouhar, Michal; Hutař, Pavel; Náhlík, Luboš; Knésl, Zdeněk

    2011-01-01

    Roč. 465, - (2011), s. 153-156 ISSN 1013-9826 R&D Projects: GA ČR GA106/09/0279; GA ČR GC101/09/J027 Institutional research plan: CEZ:AV0Z20410507 Keywords : CMOD * material interface * creep * fracture mechanics Subject RIV: JL - Materials Fatigue, Friction Mechanics

  11. Study of creep crack growth behavior of 316LN welds

    International Nuclear Information System (INIS)

    Venugopal, S.; Kumar, Yatindra; Sasikala, G.

    2016-01-01

    Creep crack growth (CCG) behavior plays an important role in the assessment of structural integrity of components operating at elevated temperature under load/stress condition. Integrity of the welded components is decided primarily by that of the weld. Creep crack growth behavior of 316LN welds prepared using consumables developed indigenously for welding the 316L(N) SS components for the Prototype Fast Breeder Reactor has been studied. The composition of the consumable is tailored to ensure about 5 FN (ferrite number) of δ ferrite in the weld deposit. Constant load CCG tests were carried out as per ASTM E1457 at different applied loads at temperatures in the range 823-923 K on CT specimens fabricated from 'V-type' weld joints with notch in the weld centre. The creep crack growth rate (α) is commonly correlated to a time dependent fracture mechanics parameter known as C*. The α3-C* correlations (α=D(C*) φ ) were established in the temperature range 823-923 K. The crack growth rates at different temperature have been compared with that given in RCC-MR. Extensive microstructural and fractographic studies using optical and scanning electron microscopy were carried out on the CCG tested specimens to understand the effect of transformation of delta ferrite on the creep damage and fracture mechanisms associated with CCG in the weld metal at different test conditions. (author)

  12. The influence of supplementary feeding to ewes and creep feeding ...

    African Journals Online (AJOL)

    KARIN KOEP

    2015-03-24

    Mar 24, 2015 ... decrease in the nutrient intake by ewes. Supplementary ... suckled lambs when pastures decline in quality and quantity or when the growth potential of lambs is not being met with ... Mutton Merino ewes and creep feed for suckling lambs grazing wheat stubble during the dry summer period. Item. Content.

  13. Multiregion analysis of creep rupture data of 316 stainless steel

    International Nuclear Information System (INIS)

    Maruyama, Kouichi; Armaki, Hassan Ghassemi; Yoshimi, Kyosuke

    2007-01-01

    A creep rupture data set of 316 stainless steel containing 319 data points at nine heats was subjected to a conventional single-region analysis and a multiregion analysis. In the former, the conventional Larson-Miller analysis was applied to the whole data set. In the latter, a data set of a single heat is divided into several data sets, so that the Orr-Sherby-Dorn (OSD) constant Q takes a unique value in each data set, and the conventional OSD analysis was applied to each divided data set. A region with a low value of Q appears in long-term creep of eight heats. Predicted values of the 10 5 h creep rupture stress of three heats were lower than the 99% confidence limit evaluated by the single-region analysis, suggesting that the single-region analysis is error prone. The multiregion analysis is necessary for the correct evaluation of the long-term creep properties of 316 stainless steel

  14. Measurement of Very Low Creep Strains: A Review

    Czech Academy of Sciences Publication Activity Database

    Kloc, Luboš; Mareček, P.

    2009-01-01

    Roč. 37, č. 1 (2009), s. 53-58 ISSN 0090-3973 R&D Projects: GA AV ČR(CZ) IAA200410701 Institutional research plan: CEZ:AV0Z20410507 Keywords : creep testing techniques * heat resistant steel * intermetallics * structural ceramics Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 0.366, year: 2009

  15. Some numerical approaches of creep, thermal shock, damage and ...

    Indian Academy of Sciences (India)

    Unknown

    steady-state creep described by a Norton type law. The authors essentially examined the relationship between the parameters of this law (stress exponent and activation energy) and the deformation mechanisms acting within the materials (Cannon and Langdon 1983, 1988). From the point of view of mechanics, the study of ...

  16. Secondary Creep Response of Hand Lay-Up GRP Composites ...

    African Journals Online (AJOL)

    Glass Reinforced Plastics (GRP) composite load bearing components are now in common use, quite often at temperatures above the ambient, where creep behaviour may be significant, as in pressurized industrial containers. This is especially true of those composites produced by the Hand Lay-Up Contact Moulding ...

  17. Physical hydrodynamic propulsion model study on creeping viscous ...

    Indian Academy of Sciences (India)

    2017-02-16

    Feb 16, 2017 ... The present investigation focusses on a mathematical study of creeping viscous flow induced by metachronal wave propagation in a horizontal ciliated ... eter and Darcy number on velocity profile, pressure gradient and trapping of bolus are discussed with the aid of graphs. It is found that with increasing ...

  18. INVESTIGATION ON NEW CREEP- AND OXIDATION-RESISTANT MATERIALS

    Czech Academy of Sciences Publication Activity Database

    Khalaj, O.; Mašek, B.; Jirková, H.; Ronešová, A.; Svoboda, Jiří

    2015-01-01

    Roč. 49, č. 4 (2015), s. 645-651 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GA14-24252S Institutional support: RVO:68081723 Keywords : ODS steel * alloys * composite * creep * Fe-Al Subject RIV: JI - Composite Material s Impact factor: 0.439, year: 2015

  19. Micromechanics of creep fracture : Simulation of intergranular crack growth

    NARCIS (Netherlands)

    Onck, Patrick; Giessen, Erik van der

    1998-01-01

    A computational model is presented to analyze intergranular creep crack growth in a polycrystalline aggregate in a discrete manner and based directly on the underlying physical micromechanisms. A crack tip process zone is used in which grains and their grain boundaries are represented discretely,

  20. Creep rupture of structures subjected to variable loading and temperature

    International Nuclear Information System (INIS)

    Wojewodzki, W.

    1975-01-01

    The aim of the present paper is to show on the basis of equations and the analysis of creep mechanisms the possibilities of a description of the creep behavior of material under variable temperature and loading conditions. Also the influence of cyclic proportional loading and temperature gradient upon the rupture life and strains of a thick cylinder is investigated in detail. The obtained theoretical creep curves coincide with the experimental results for investigated steel in the temperature range from 500 0 C to 575 0 C. The constitutive equations together with the functions determined previously are applied to solve the problem of thick cylinder subjected to cyclic proportional pressure and temperature gradient. Numerical results for the thick steel cylinder are presented both in diagrammatical and tabular form. The obtained new results clearly show the significant influence of temperature gradient, cyclic temperature gradient, and cyclic pressure upon the stress redistribution, the magnitude of deformation, the propagation of the front damage and the rupture life. It was found that small temperature fluctuations at elevated temperature can shorten the rupture life very considerably. The introduced description of the creep rupture behavior of material under variable temperature and loading conditions together with the results for the thick cylinder indicate the possibilities of solutions of practical problems encountered in structural mechanics of reactor technology

  1. Double minimum creep of single crystal Ni-base superalloys

    Czech Academy of Sciences Publication Activity Database

    WU, X.; Wollgramm, P.; Somsen, C.; Dlouhý, Antonín; Kostka, A.; Eggeler, G.

    2016-01-01

    Roč. 112, JUN (2016), s. 242-260 ISSN 1359-6454 R&D Projects: GA ČR(CZ) GA14-22834S Institutional support: RVO:68081723 Keywords : Single crystal Ni-base superalloys * Primary creep * Transmission electron microscopy * Dislocations * Stacking fault s Subject RIV: JG - Metallurgy Impact factor: 5.301, year: 2016

  2. Analysis of local microstructure after shear creep deformation

    Czech Academy of Sciences Publication Activity Database

    Peter, D.; Viswanathan, G.B.; Dlouhý, Antonín; Eggeler, G.

    2010-01-01

    Roč. 58, č. 19 (2010), s. 6431-6443 ISSN 1359-6454 R&D Projects: GA ČR GA106/07/0762 Institutional research plan: CEZ:AV0Z20410507 Keywords : Titanium aluminides * Shear creep deformation * Transmission electron microscopy * Dislocations * Twinning Subject RIV: JG - Metallurgy Impact factor: 3.781, year: 2010

  3. Role of small amount of MgO and ZrO2 on creep behaviour of high ...

    Indian Academy of Sciences (India)

    Unknown

    with a similar ionic size, demonstrates that the ionic valency of dopants also plays a crucial role in creep since magnesia does not significantly alter creep whereas zirconia retards creep substantially. Magnesia doped alumina deforms by Coble diffusion creep whereas zirconia doped alumina deforms by an interface ...

  4. Orthotropic creep in polyethylene glycol impregnated archaeological oak from the Vasa ship - Results of creep experiments in a museum-like climate

    Science.gov (United States)

    Vorobyev, Alexey; van Dijk, Nico P.; Kristofer Gamstedt, E.

    2018-02-01

    Creep in archaeological oak samples and planks from the Vasa ship impregnated with polyethylene glycol (PEG) has been studied in museum-like climate. Creep studies of duration up to three years have been performed in nearly constant relative humidity and temperature of the controlled museum climate. Cubic samples were subjected to compressive creep tests in all orthotropic directions. Additionally, the creep behaviour of planks with and without PEG and of recent oak was tested in four-point bending. The experimental results have been summarised and also compared with reference results from recent oak wood. The effect of variable ambient conditions on creep and mass changes is discussed. The experimental results of creep in the longitudinal direction showed deformations even for the low stresses. There is relatively much more scatter in creep behaviour, and not all samples showed linear viscoelastic response. The creep in radial and tangential directions of the cubes and the plank samples showed a strong dependency on the ambient conditions. Some samples showed expansion for decreasing moisture content, possibly caused by the thermal expansion of the PEG component. For the planks, increasing creep deformation was observed induced by changing ambient conditions. Such behaviour may be related to e.g. oscillations in ambient conditions and presence of PEG in the wood cell wall and cell lumen. The behaviour of PEG archaeological wood depends on the level of deterioration that occurred over centuries. However, although the findings presented here apply to this specific case, they provide a unique view on such wood.

  5. Creep deformation in near-γ TiAl. Part 1: The influence of microstructure on creep deformation in Ti-49Al-1V

    International Nuclear Information System (INIS)

    Worth, B.D.; Jones, J.W.; Allison, J.E.

    1995-01-01

    The influence of microstructure on creep deformation was examine in the e near-γ TiAl alloy Ti-49Al-1V. Specifically, microstructures with varying volume fractions of lamellar constituent were produced through thermomechanical processing. Creep studies were conducted on these various microstructures under constant load in air at temperatures between 760 C and 870 C and at stresses ranging from 50 to 200 MPa. Microstructure significantly influences the creep behavior of this alloy, with a fully lamellar microstructure yielding the highest creep resistance of the microstructures examined. Creep resistance is dependent on the volume fraction of lamellar constituent, with the lowest creep resistance observed at intermediate lamellar volume fractions. Examination of the creep deformation structure revealed planar slip of dislocations in the equiaxed γ microstructure, while sub-boundary formation was observed in the duplex microstructure. The decrease in creep resistance of the duplex microstructure, compared with the equiaxed γ microstructure, is attributed to an increase in dislocation mobility within the equiaxed γ constituent, that results from partitioning of oxygen from the γ phase to the α 2 phase. Dislocation motion in the fully lamellar microstructure was confined to the individual lamellae, with no evidence of shearing of γ/γ or γ/α 2 interfaces. This suggests that the high creep resistance of the fully lamellar microstructure is a result of the fine spacing of the lamellar structure, which results in a decreased effective slip length for dislocation motion over that found in duplex and equiaxed γ microstructures

  6. Creep strength of hastelloy X TIG-welded cylinder under internal pressure at elevated temperature

    International Nuclear Information System (INIS)

    Udoguchi, Teruyoshi; Indo, Hirosato; Isomura, Kazuyuki; Kobatake, Kiyokazu; Nakanishi, Tsuneo.

    1981-01-01

    Creep tests on circumferentially TIG-welded Hastelloy x cylinders were carried out under internal pressure for the investigation of structural behavior of welded components in high temperature environment. The creep rupture strength of TIG-welded cylinders was much lower than that of non-welded cylinders, while such reduction was not found in uniaxial creep tests on TIG-welded bars. It was deduced that the reduction was due to the low ductility (ranging from 1 to 5%) of the weld metal to which enhanced creep was induced by the adjacent base metal whose creep strain rate was much higher than that of the weld metal. Therefore, uniaxial creep tests on bar specimens is not sufficient for proper assessment of the creep rupture strength of welded components. Both creep strain rate and creep ductility should be concerned for the assessment. Creep tests by using components such as cylinder under internal pressure are recommendable for the confirmation of creep strength of welded structures and components. (author)

  7. Mechanical modeling of creep, swelling and damage under irradiation for polycrystalline metals

    International Nuclear Information System (INIS)

    Murakami, S.; Mizuno, M.; Okamoto, T.

    1991-01-01

    A constitutive equation of creep, swelling and damage under irradiation for polycrystalline metals applicable to structural analyses in multiaxial state of stress is developed. After reviewing microscopic mechanisms of irradiation creep and swelling, the relevant theories proposed so far from the view point of metallurgical physics and their applicability are discussed first. Then a constitutive model is developed by assuming that creep under irradiation can be decomposed into irradiation-affected thermal creep and irradiation-induced creep. By taking account of the Stress-Induced Preferential Absorption (SIPA) mechanism, the irradiation-induced creep is represented by an isotropic tensor function of order one and zero with respect to stress, which is, at the same time, the function of neutron flux and neutron fluence. The volumetric part of the irradiation-induced creep is identified with swelling. The irradiation-affected thermal creep is described by modifying Kachanov-Rabotnov theory for stress-controlled creep and creep damage by incorporating the effect of irradiation. Finally irradiation creep and swelling of 20% cold-worked type 316 stainless steel at elevated temperature are predicted by the proposed constitutive equations, and the numerical results are compared with the corresponding experimental results. (orig.)

  8. Biaxial thermal creep of Inconel 617 and Haynes 230 at 850 and 950 °C

    International Nuclear Information System (INIS)

    Tung, Hsiao-Ming; Mo, Kun; Stubbins, James F.

    2014-01-01

    The biaxial thermal creep behavior of Inconel 617 and Haynes 230 at 850 and 950 °C was investigated. Biaxial stresses were generated using the pressurized tube technique. The detailed creep deformation and fracture mechanism have been studied. Creep curves for both alloys showed that tertiary creep accounts for a greater portion of the materials’ life, while secondary creep only accounts for a small portion. Fractographic examinations of the two alloys indicated that nucleation, growth, and coalescence of creep voids are the dominant micro-mechanisms for creep fracture. At 850 °C, alloy 230 has better creep resistance than alloy 617. When subjected to the biaxial stress state, the creep rupture life of the two alloys was considerably reduced when compared to the results obtained by uniaxial tensile creep tests. The Monkman–Grant relation proves to be a promising method for estimating the long-term creep life for alloy 617, whereas alloy 230 does not follow the relation. This might be associated with the significant changes in the microstructure of alloy 230 at high temperatures

  9. Carbon dioxide dangers demonstration model

    Science.gov (United States)

    Venezky, Dina; Wessells, Stephen

    2010-01-01

    Carbon dioxide is a dangerous volcanic gas. When carbon dioxide seeps from the ground, it normally mixes with the air and dissipates rapidly. However, because carbon dioxide gas is heavier than air, it can collect in snowbanks, depressions, and poorly ventilated enclosures posing a potential danger to people and other living things. In this experiment we show how carbon dioxide gas displaces oxygen as it collects in low-lying areas. When carbon dioxide, created by mixing vinegar and baking soda, is added to a bowl with candles of different heights, the flames are extinguished as if by magic.

  10. Tensile and Creep-Rupture Evaluation of a New Heat of Haynes Alloy 25

    Energy Technology Data Exchange (ETDEWEB)

    Shingledecker, J.P.; Glanton, D.B.; Martin, R.L.; Sparks, B.L.; Swindeman, R.W.

    2007-02-14

    From 1999 to 2006, a program was undertaken within the Materials Science and Technology Division, formerly the Metals and Ceramics Division, of Oak Ridge National Laboratory to characterize the tensile and creep-rupture properties of a newly produced heat of Haynes alloy 25 (L-605). Tensile properties from room temperature to 1100 C were evaluated for base material and welded joints aged up to 12,000 hours at 675 C. Creep and creep-rupture tests were conducted on base metal and cross-weldments from 650 to 950 C. Pressurized tubular creep tests were conducted to evaluate multiaxial creep-rupture response of the material. Over 800,000 hours of creep test data were generated during the test program with the longest rupture tests extending beyond 38,000 hours, and the longest creep-rate experiments exceeding 40,000 hours.

  11. Study on Flexural Creep Parameters of Overlayed Particleboard by Natural and Melaminated Veneers

    Directory of Open Access Journals (Sweden)

    Abdollah Najafi

    2012-06-01

    Full Text Available In this study, effects of natural and artificial veneer on flexural creep behavior of particleboard was investigated. Particleboard panels were prepared from Pars Neopan industries with 660 kg/m3 density and then overlaid by natural and melamine veneers. Their creep behavior was compared to control particleboard. For evaluating maximum bending load in static flexural test, specimens were cut from panels according to ASTM D 1037 with dimensions of 370×50×16 mm. Then, The flexural creep tests at 20% and 40% of failure bending load was applied to test specimens. Results of flexural tests indicated that the MOR and MOE values of veneered particleboard were highest. Results of creep showed that levels of stresses are effective on all creep parameters, but showed less effect on relative creep. Also, creep parameters less effective on specimens overlaid by natural veneer.

  12. Treatment of effluent at the Saclay Centre d'Etudes Nucleaires (1960)

    International Nuclear Information System (INIS)

    Wormser, G.

    1960-01-01

    The Centre d'Etudes Nucleaires at Saclay possesses several installations from which liquid radioactive effluent is rejected, and it has thus been found necessary to construct a station for the purification of radioactive liquids and to settle various chemical, analytical and technological problems. This report describes, in the following order: - the disposal possibilities at the Centre d'Etudes Nucleaires, Saclay, - the effluents produced at the centre, - the set-up for collecting effluent, - treatment of the effluent, - results of these treatments. (author) [fr

  13. Diffusion Creep of Enstatite at High Pressures Under Hydrous Conditions

    Science.gov (United States)

    Zhang, Guinan; Mei, Shenghua; Song, Maoshuang; Kohlstedt, David L.

    2017-10-01

    Mantle convection and large-scale plate motion depend critically on the nature of the lithosphere-asthenosphere boundary and thus on the viscosity structure of Earth's upper mantle, which is determined by the rheological properties of its constituent minerals. To constrain the flow behavior of orthopyroxene, the second most abundant constituent of the upper mantle, deformation experiments were carried out in triaxial compressive creep on fine-grained ( 6 μm) samples of enstatite at high pressures (3.8-6.3 GPa) and high temperatures (1323-1573 K) using a deformation-DIA apparatus. Based on results from this study, the deformation behavior of enstatite is quantitatively presented in the form of a flow law that describes the dependence of deformation rate on differential stress, water fugacity, temperature, and pressure. Specifically, the creep rate depends approximately linearly on stress, indicating deformation in the diffusion creep regime. A least squares regression fit to our data yielded a flow law for diffusion creep with an activation energy of 200 kJ/mol and an activation volume of 14 × 10-6 m3/mol. The magnitude of the water-weakening effect is similar to that for olivine with a water fugacity exponent of r ≈ 0.7. This strong dependence of viscosity on water fugacity (concentration) indicates that the viscosity of an orthopyroxene-bearing mantle varies from one geological setting to another, depending on the large-scale water distribution. Based on the rheology contrast between olivine and enstatite, we conclude that olivine is weaker than enstatite throughout most of the upper mantle except in some shallow regions in the diffusion creep regime.

  14. Estimation of the controlling stress in creep fracture

    International Nuclear Information System (INIS)

    Henderson, J.; Ferguson, F.R.

    1975-01-01

    The implementation of correct criterion in creep design, has been shown to be of fundamental significance in the assessment of component life. The present report considers the problem of the means whereby the criterion may be derived for a particular metal without the availability of sophisticated complex-stress testing equipment and procedures such as the combined tension and torsion tests on thin walled tubular specimens employed in the earlier fundamental researches on the subject. By investigating a wide spectrum of engineering metals it was established that for homogeneous stress conditions two criteria appeared to be sufficient to cover all the metals studied for complex-stress creep fracture, either the maximum principal stress or the octahedral shear stress criterion. Further, it was found that those metals which developed random and continuous cracking during creep were controlled with respect to fracture time by the maximum principal stress, while metals which showed virtually no cracking were governed by the octahedral shear stress or second order invariant. The physical nature of the final fracture (transcrystalline or inter-crystalline), contrary to considerable current concepts, was found to be unrelated to which criterion was operative. Having reduced the possible fracture criteria to two, it only remained to develop a simple test method exploiting this finding to achieve the precise identification for a particular metal. Seven metals including aluminium, copper, titanium, cast iron and three steels have been investigated in the present report at temperatures where creep conditions are operative. The results have shown that the method leads to sufficiently accurate prediction of the complex stress creep fracture criterion for the metals studied

  15. Long-term performance of ceramic matrix composites at elevated temperatures: Modelling of creep and creep rupture

    Energy Technology Data Exchange (ETDEWEB)

    Curtin, W.A.; Fabeny, B.; Ibnabdeljalil, M.; Iyengar, N.; Reifsnider, K.L. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States). Dept. of Engineering Science and Mechanics

    1996-07-31

    The models developed, contain explicit dependences on constituent material properties and their changes with time, so that composite performance can be predicted. Three critical processes in ceramic composites at elevated temperatures have been modeled: (1) creep deformation of composite vs stress and time-dependent creep of fibers and matrix, and failure of these components; (2) creep deformation of ``interface`` around broken fibers; and (3) lifetime of the composite under conditions of fiber strength loss over time at temperature. In (1), general evolution formulas are derived for relaxation time of matrix stresses and steady-state creep rate of composite; the model is tested against recent data on Ti-MMCs. Calculations on a composite of Hi-Nicalon fibers in a melt-infiltrated SiC matrix are presented. In (2), numerical simulations of composite failure were made to map out time-to-failure vs applied load for several sets of material parameters. In (3), simple approximate relations are obtained between fiber life and composite life that should be useful for fiber developers and testers. Strength degradation data on Hi-Nicalon fibers is used to assess composite lifetime vs fiber lifetime for Hi-Nicalon fiber composites.

  16. Relation between creep compliance and elastic modulus in organic-rich shales observed through laboratory experiments.

    Science.gov (United States)

    Sone, Hiroki; Zoback, Mark

    2013-04-01

    We studied the ductile creep behavior of organic-rich shales from shale gas reservoirs in North America through laboratory triaxial experiments to better understand controls on the physical behavior of these rocks over time and the effect of creep on other rock properties. Laboratory experiments conducted at room-temperature conditions show that creep deformation observed at in-situ differential stress conditions is approximately linear with the applied differential pressure. The creep behavior is also anisotropic such that creep occurs more in the bedding-perpendicular direction than in the bedding-parallel direction. The reduction in sample volume during creep suggests that the creep is accommodated by a small amount of pore compaction occurring in the clay-aggregates and/or the relatively porous kerogen in the rock. Thus, the tendency to creep (creep compliance) is generally observed to increases with clay and kerogen volume. However, the strongest correlation is found between creep compliance and Young's modulus. A strong negative correlation between creep compliance and elastic Young's modulus exists regardless of the sample orientation and despite the wide range of sample mineralogy (5-50% clay, 5-60% quartz-feldspar-pyrite, 0-80% carbonates). This correlation is quite interesting as inelastic creep and elastic stiffness depend on somewhat different physical attributes. We attempt to quantitatively explain the correlation between creep behavior and elastic stiffness by appealing to a stress-partitioning that occurs between the soft components (clay and kerogen) and stiff components (quartz, feldspar, pyrite, carbonates) of the shale rock. First, the stress-partitioning occurring within the soft and stiff components is quantified based on the rock composition, elastic properties of the individual components, and the overall average Young's modulus of the rock. By combining the stress-partitioning behavior with knowledge that the creep behavior is linear

  17. Brittle Creep of Tournemire Shale: Orientation, Temperature and Pressure Dependences

    Science.gov (United States)

    Geng, Zhi; Bonnelye, Audrey; Dick, Pierre; David, Christian; Chen, Mian; Schubnel, Alexandre

    2017-04-01

    Time and temperature dependent rock deformation has both scientific and socio-economic implications for natural hazards, the oil and gas industry and nuclear waste disposal. During the past decades, most studies on brittle creep have focused on igneous rocks and porous sedimentary rocks. To our knowledge, only few studies have been carried out on the brittle creep behavior of shale. Here, we conducted a series of creep experiments on shale specimens coming from the French Institute for Nuclear Safety (IRSN) underground research laboratory located in Tournemire, France. Conventional tri-axial experiments were carried under two different temperatures (26˚ C, 75˚ C) and confining pressures (10 MPa, 80 MPa), for three orientations (σ1 along, perpendicular and 45˚ to bedding). Following the methodology developed by Heap et al. [2008], differential stress was first increased to ˜ 60% of the short term peak strength (10-7/s, Bonnelye et al. 2016), and then in steps of 5 to 10 MPa every 24 hours until brittle failure was achieved. In these long-term experiments (approximately 10 days), stress and strains were recorded continuously, while ultrasonic acoustic velocities were recorded every 1˜15 minutes, enabling us to monitor the evolution of elastic wave speed anisotropy. Temporal evolution of anisotropy was illustrated by inverting acoustic velocities to Thomsen parameters. Finally, samples were investigated post-mortem using scanning electron microscopy. Our results seem to contradict our traditional understanding of loading rate dependent brittle failure. Indeed, the brittle creep failure stress of our Tournemire shale samples was systematically observed ˜50% higher than its short-term peak strength, with larger final axial strain accumulated. At higher temperatures, the creep failure strength of our samples was slightly reduced and deformation was characterized with faster 'steady-state' creep axial strain rates at each steps, and larger final axial strain

  18. CARBON DIOXIDE FIXATION.

    Energy Technology Data Exchange (ETDEWEB)

    FUJITA,E.

    2000-01-12

    Solar carbon dioxide fixation offers the possibility of a renewable source of chemicals and fuels in the future. Its realization rests on future advances in the efficiency of solar energy collection and development of suitable catalysts for CO{sub 2} conversion. Recent achievements in the efficiency of solar energy conversion and in catalysis suggest that this approach holds a great deal of promise for contributing to future needs for fuels and chemicals.

  19. IFMIF - Design Study for in Situ Creep Fatigue Tests

    International Nuclear Information System (INIS)

    Gordeev, S.; Heinzel, V.; Simakov, St.; Stratmanns, E.; Vladimirov, P.; Moeslang, A.

    2006-01-01

    While the high flux volume (20-50 dpa/fpy) of the International Fusion Materials Irradiation Facility (IFMIF) is dedicated to the irradiation of ∼ 1100 qualified specimens that will be post irradiation examined after disassembling in dedicated Hot Cells, various in situ experiments are foreseen in the medium flux volume (1-20 dpa/fpy). Of specific importance for structural lifetime assessments of fusion power reactors are instrumented in situ creep-fatigue experiments, as they can simulate realistically a superposition of thermal fatigue or creep fatigue and irradiation with fusion relevant neutrons. Based on former experience with in situ fatigue tests under high energy light ion irradiation, a design study has been performed to evaluate the feasibility of in situ creep fatigue tests in the IFMIF medium flux position. The vertically arranged test module for such experiments consists basically of a frame similar to a universal testing machine, but equipped with three pulling rods, driven by independent step motors, instrumentation systems and specimen cooling systems. Therefore, three creep fatigue specimens may be tested at one time in this apparatus. Each specimen is a hollow tube with coolant flow in the specimen interior to maintain individual specimen temperatures. The recently established IFMIF global 3D geometry model was used together the latest McDeLicious code for the neutral and charged particle transport calculations. These comprehensive neutronics calculations have been performed with a fine special resolution of 0.25 cm 3 , showing among others that the specimens will be irradiated with a homogeneous damage rate of up to 13(∼ 9%) dpa/fpy and a fusion relevant damage to helium ratio of 10-12 appm He/dpa. In addition, damage and gas production rates as well as the heat deposition in structural parts of the test module have been calculated. Despite of the vertical gradients in the nuclear heating, CFD code calculations with STAR-CD revealed very

  20. The evaluation of the creep properties of ZIRLO cladding using the ring specimen

    International Nuclear Information System (INIS)

    Bae, Bong Kook; Koo, Jae Mean; Seok, Chang Sung

    2004-01-01

    In this study, we suggested the ring creep test using the ring specimen of Arsene for estimating the burst creep properties of the cladding in stead of burst creep test. For this objective, we used the load-displacement conversion relationship of ring specimen called LCRR which had been determined on our previous study at high temperature by performing the ring tensile test and the numerical analysis. Then we carried out both the ring creep test and the burst creep test between 350 .deg. C and 600 .deg. C which were higher then the in-service temperature of the cladding in a reactor. The creep properties from the ring creep test with applying LCRR were compared with those from the burst creep test of closed-end specimens. From the results, it could be seen an very strong relationship between them, especially in Larson-Miller parameter. So, it is expected that we can easily anticipate the creep properties of not only claddings but also various small pressure pipes using the ring creep test

  1. The evaluation of the creep properties of ZIRLO cladding using the ring specimen

    International Nuclear Information System (INIS)

    Bae, Bong Kook; Koo, Jae Mean; Seok, Chang Sung

    2005-01-01

    In this study, we suggested the ring creep test using the ring specimen of Arsene for estimating the burst creep properties of the cladding in stead of burst creep test. For this objective, we used the load-displacement conversion relationship of ring specimen called LCRR which had been determined on our previous study at high temperature by performing the ring tensile test and the numerical analysis. Then we carried out both the ring creep test and the burst creep test between 350 .deg. C and 600 .deg. C which were higher than the in-service temperature of the cladding in a reactor. The creep properties from the ring creep test with applying LCRR were compared with those from the burst creep test of closed-end specimens. From the results, it could be seen an very strong relationship between them, especially in Larson-Miller parameter. So, it is expected that we can easily predict the creep properties of not only claddings but also various small pressure pipes using the ring creep test

  2. Elastic modulus correction term in creep activation energies: applied to oxide dispersion strengthened superalloy

    International Nuclear Information System (INIS)

    Malu, M.; Tien, J.K.

    1975-01-01

    Creep properties of Inconel alloy MA 753 were studied. It was found that below 1500 0 F, where elastic modulus is weakly dependent upon temperature, the modulus correction term to creep activation energy is small. Accordingly, for superalloy systems such as INCONEL alloy MA 753 and Mar-M 200, which show high apparent creep activation energies at this temperature, modulus corrections are unimportant and their true activation energies remain high. In contrast, at very high temperatures, as a consequence of the high temperature values and the sharper changes in the slope of the young modulus vs. temperature curve, the elastic modulus correction term can be significant--it is found to be about -142 kcal/ mole for INCONEL alloy MA 753 at 1900 0 F and thus reducing the creep activation energy at this temperature from 202 kcal/mole to that of vacancy self-diffusion. It is noted that in general and especially at high temperatures the creep equation used to analyze creep data and creep activation energies must include the elastic modulus terms. Up to now, the neglect of these terms have by-in-large been justified. However, with the advent of very high temperature creep tests on the high temperature dispersion strengthened systems, the modulus terms must be taken into consideration. With respect to alloy designing for high temperature creep resistance, in addition to other considerations to obtain high temperature creep resistance, a high value of elastic modulus with a weak dependence on temperature at high temperatures is required

  3. Flexural creep of coated SiC-fiber-reinforced glass-ceramic composites

    International Nuclear Information System (INIS)

    Sun, E.Y.

    1995-01-01

    This study reports the flexural creep behavior of a fiber-reinforced glass-ceramic and associated changes in microstructure. SiC fibers were coated with a dual layer of SiC/BN to provide a weak interface that was stable at high temperatures. Flexural creep, creep-rupture, and creep-strain recovery experiments were conducted on composite material and barium-magnesium aluminosilicate matrix from 1,000 to 1,200 C. Below 1,130 C, creep rates were extremely low (∼10 -9 s -1 ), preventing accurate measurement of the stress dependence. Above 1,130 C, creep rates were in the 10 -8 s -1 range. The creep-rupture strength of the composite at 1,100 C was about 75--80% of the fast fracture strength. Creep-strain recovery experiments showed recovery of up to 90% under prolonged unloading. Experimental creep results from the composite and the matrix were compared, and microstructural observations by TEM were employed to assess the effectiveness of the fiber coatings and to determine the mechanism(s) of creep deformation and damage

  4. A constitutive equation of irradiation creep and swelling under neutron irradiation

    International Nuclear Information System (INIS)

    Murakami, Sumio; Mizuno, Mamoru; Okamoto, Toshiaki.

    1990-01-01

    A constitutive equation of irradiation creep for irradiated materials applicable to structural analyses in a multiaxial state of stress was developed. After reviewing microscopic mechanisms of irradiation creep and swelling, the relevant theories proposed from the view point of metallurgical physics and their applicability were discussed first. Then a constitutive model was developed by assuming that irradiation creep can be decomposed into irradiation-enhanced creep and irradiation-induced creep. By taking account of the SIPA (Stress Induced Preferential Absorption) mechanism, the irradiation-induced creep was represented by an isotropic tensor function of order one and zero with respect to stress, which is, at the same time, the function of neutron flux and neutron fluence. The volumetric part of the irradiation-induced creep was identified with swelling. The irradiation-enhanced creep was described by modifying Kachanov-Rabotnov creep damage theory by incorporating the effect of irradiation. Finally the irradiation creep and swelling of type 316 stainless steel at elevated temperatures were predicted by the proposed constitutive equation, and the numerical results were compared with the corresponding experimental results. (author)

  5. Creep Rupture Properties for Base and Weld Metals of Alloy 617

    International Nuclear Information System (INIS)

    Kim, Woo-Gon; Kim, Min-Hwan; Park, Jae-Young; Ekaputra, I. M. W.

    2015-01-01

    The allowable deformation in the welds is also restricted to half the deformation permitted for the base metal, since the ductility of the welds at elevated temperatures is generally low. For a design use, the data of the tensile and creep properties for Alloy 617 WM should be sufficiently provided, and in particular, to develop a design code of Alloy 617 WM. However, the data for the WM are very rare and limited until now, although the data for the BM are available in the ASME draft code case, which was suspended at the end of the 1980s owing to a lack of support and interes. In this report, the creep data for Alloy 617 WM, which was fabricated by a gas tungsten arc welding (GTAW) procedure, were obtained by a series of creep tests at 800 .deg. C, and the creep properties of the WM were compared with those of the BM. The high-temperature creep properties for Alloy 617 WM, fabricated by a gas tungsten arc welding (GTAW) procedure, were investigated by a series of creep tests with different stress levels at 800 .deg. C, and the creep test data for the WM were compared with those of the BM. From the results, it was found that the WM had a slightly longer creep rupture life and lower creep rate than the BM, and a particularly lower rupture elongation. The lower creep rate in the WM was due to the lower rupture elongation than the BM

  6. Physical-Mechanism Exploration of the Low-Cycle Unified Creep-Fatigue Formulation

    Directory of Open Access Journals (Sweden)

    Dan Liu

    2017-09-01

    Full Text Available Background—Creep-fatigue behavior is identified as the incorporated effects of fatigue and creep. One class of constitutive-based models attempts to evaluate creep and fatigue separately, but the interaction of fatigue and creep is neglected. Other models treat the damage as a single component, but the complex numerical structures that result are inconvenient for engineering application. The models derived through a curve-fitting method avoid these problems. However, the method of curving fitting cannot translate the numerical formulation to underlying physical mechanisms. Need—Therefore, there is a need to develop a new creep-fatigue formulation for metal that accommodates all relevant variables and where the relationships between them are consistent with physical mechanisms of fatigue and creep. Method—In the present work, the main dependencies and relationships for the unified creep-fatigue equation were presented through exploring what the literature says about the mechanisms. Outcomes—This shows that temperature, cyclic time and grain size have significant influences on creep-fatigue behavior, and the relationships between them (such as linear relation, logarithmical relation and power-law relation are consistent with phenomena of diffusion creep and crack growth. Significantly, the numerical form of “1 − x” is presented to show the consumption of creep effect on fatigue capacity, and the introduction of the reference condition gives the threshold of creep effect. Originality—By this means, the unified creep-fatigue equation is linked to physical phenomena, where the influence of different dependencies on creep fatigue was explored and relationships shown in this equation were investigated in a microstructural level. Particularly, a physical explanation of the grain-size exponent via consideration of crack-growth planes was proposed.

  7. Creep strength and microstructural evolution of 9-12% Cr heat resistant steels during creep exposure at 600 C and 650 C

    Energy Technology Data Exchange (ETDEWEB)

    Mendez Martin, Francisca [Graz Univ. of Technology (Austria). Inst. for Materials Science and Welding; Panait, Clara Gabriela [MINES ParisTech, UMR CNRS, Evry (France). Centre des Materiaux; V et M France CEV, Aulnoye-Aymeries (France); Bendick, Walter [Salzgitter Mannesmann Forschung GmbH (SZMF), Duisburg (DE)] (and others)

    2010-07-01

    9-12% Cr heat resistant steels are used for applications at high temperatures and pressures in steam power plants. 12% Cr steels show higher creep strength and higher corrosion resistance compared to 9% Cr steels for short term creep exposure. However, the higher creep strength of 12 %Cr steels drops increasingly after 10,000-20,000 h of creep. This is probably due to a microstructural instability such as the precipitation of new phases (e.g. Laves phases and Z-phases), the growth of the precipitates and the recovery of the matrix. 9% Cr and 12% Cr tempered martensitic steels that have been creep tested for times up to 50,000 h at 600 C and 650 C were investigated using Transmission Electron Microscopy (TEM) on extractive replicas and thin foils together with Backscatter Scanning Electron Microscopy (BSE-SEM) to better understand the different creep behaviour of the two different steels. A significant precipitation of Laves phase and low amounts of Z-phase was observed in the 9% Cr steels after long-term creep exposure. The size distribution of Laves phases was measured by image analysis of SEM-BSE images. In the 12% Cr steel two new phases were identified, Laves phase and Z-phase after almost 30,000 h of creep test. The quantification of the different precipitated phases was studied. (orig.)

  8. Influence of microstructural parameters on the deformation and failure behaviour of the ODS alloy PM 2000 under creep and creep-fatigue loading

    International Nuclear Information System (INIS)

    Bothe, K.; Kussmaul, K.; Maile, K.

    1999-01-01

    The influence of grain size, manufacturing type and specimen direction (anisotropy) with respect to deformation and failure behaviour under creep, fatigue and creep-fatigue load was investigated. Thus, a basis for the correlation between microstructure and mechanical behaviour has been established. The specific damage and failure behaviour could be explained by means of the different microstructures observed. (orig.)

  9. Creep-rupture behavior of candidate Stirling engine iron supperalloys in high-pressure hydrogen. Volume 2: Hydrogen creep-rupture behavior

    Science.gov (United States)

    Bhattacharyya, S.; Peterman, W.; Hales, C.

    1984-01-01

    The creep rupture behavior of nine iron base and one cobalt base candidate Stirling engine alloys is evaluated. Rupture life, minimum creep rate, and time to 1% strain data are analyzed. The 3500 h rupture life stress and stress to obtain 1% strain in 3500 h are also estimated.

  10. Modeling of the non-monotonous viscoplastic behavior of uranium dioxide

    Science.gov (United States)

    Sauter, F.; Leclercq, S.

    2003-10-01

    In order to evaluate the stress level during pellet cladding mechanical interaction (PCMI), Electricité de France is involved in a large program of investigation of the mechanical properties of both fuel pellets and claddings. In this paper, we focus on the mechanical behavior of uranium dioxide. These pellets exhibit a yield point during strain hardening tests and sigmoı̈dal creep curves, that is inflection points characteristic of a non-monotonous viscoplastic flow in the first stages of the tests. Inspired by Alexander and Haasen's work upon single crystal silicon, we develop a dislocation-based model that is able to describe the viscoplasticity of uranium dioxide in the range of temperature and stress of the PCMI. After developing this model, we introduce it into the Pilvin's polycrystalline approach. The self-consistency of the polycrystalline approach in the case of a non-monotonous viscoplastic flow is demonstrated in an independent article.

  11. Etude comparative de deux produits de neem (huile et poudre) sur ...

    African Journals Online (AJOL)

    Etude comparative de deux produits de neem (huile et poudre) sur les stades préimaginaux du moustique Culex quinquefasciatus(Diptera : Culicidae) ... for nymphs only contact effects are showed. Neem oil formulated 1 % appears more effective than neem powder 0.3 % for mosquitoes control in aquatic environment.

  12. Etude morphologique d'un cas de femme XY avec dysgénésie ...

    African Journals Online (AJOL)

    Mots clés : Etude morphologique, femme XY, dysgénésie gonadique pure. The authors describe the morphological features of a twenty years old female, without ambiguous genitalia, presenting a 46,XY karyotype, normal female external genitalia and gonadal dysgenesis. She has an android type of morpho dysplasia and ...

  13. English Department Reforms at the Hautes Etudes Commerciales: Entering the Nineties.

    Science.gov (United States)

    Shanahan, Daniel

    1993-01-01

    Discusses the reforms made in the fall of 1990 in the English department at the Ecole Hautes Etudes Commerciales (Paris, France), which were based on the basis of a combination of literature-culture and second- and foreign-language acquisition pedagogical biases. (four references) (VWL)

  14. Contribution a l'etude des plantes alimentaires mineures dans la ...

    African Journals Online (AJOL)

    Contribution a l'etude des plantes alimentaires mineures dans la prefecture de Dankpen (Togo). AB Kebenzikato, S Akpavi, K Batawila, K Wala, M Dourma, K Kossi-Titrikou, KS Amouzou, I Butare, H Dantsey-Barry, K Akpagana ...

  15. 152 Etude de cas sur l'impact des amendements organiques vis-à ...

    African Journals Online (AJOL)

    john mukalay

    Etude de cas sur l'impact des amendements organiques vis-à-vis de la salinité en culture de bananier. Michel Mazinga KWEY1, Séverin Kalala BANZE2 et John Banza MUKALAY2*. 1Laboratoire des cultures in vitro, Département de phytotechnie, Faculté des sciences agronomiques,. Université de Lubumbashi, BP 1825, ...

  16. Etude de l'influence des modes de transformation sur les teneurs en ...

    African Journals Online (AJOL)

    Etude de l'influence des modes de transformation sur les teneurs en lycopène de quatre variétés de tomates de la région du nord du Burkina Faso. I Sawadogo, M Koala, C Dabire, LP Ouattara, VBEJT Bazie, A Hema, C Gnoula, E Pale, RHC Nebie ...

  17. Etude comparée des paramètres agromorphologiques de dix (10 ...

    African Journals Online (AJOL)

    Etude comparée des paramètres agromorphologiques de dix (10) variétés de patate douce ( Ipomoea batatas (L.) Lam cultivées au champ dans deux (2) conditions climatiques au Tchad et au Burkina Faso.

  18. Etude comparative de la flore aux abords des cours d'eau dans les ...

    African Journals Online (AJOL)

    Etude comparative de la flore aux abords des cours d'eau dans les zones hypo et hyper endémiques d'ulcère de Buruli en Côte d'Ivoire. C. Cisse Boni, E. Ehouman, D. Soro, M.W. Kone, A. Bakayoko, F. Dembele, K. Bauthire, M Dosso ...

  19. Detection and analysis of the stored grain insect creeping sound

    Science.gov (United States)

    Geng, Senlin; Zhang, Xiuqin; Zhao, Wei

    2017-09-01

    With the random acoustic source model as the theory model of the stored grain insects creeping, the sounds, of 20 Alphitobius diaperinus Panzer in wheat and 20 Tribolium castaneum Herbst adults in corn, are detected, respectively. By using Matlab, the original sound signals are reproduced and the de-noised signals are obtained. The power spectrums characteristics analysis are made. It is shown that the random acoustic source model is effective for the stored grain insect creeping sound detection, and their power spectrums are all discrete, where the highest frequency is 1600 Hz, the main frequency 205 Hz in the former, and the highest frequency is 800 Hz, the main frequency 350 Hz the latter, which may be used to distinguish different types insects in grain.

  20. Microstructural observation on helium injected and creep ruptured JPCA

    International Nuclear Information System (INIS)

    Yamamoto, N.; Shiraishi, H.; Hishinuma, A.

    1986-01-01

    Detailed and quantitative TEM observation was performed on high temperature helium injected and creep ruptured JPCA to seek the prominent TiC distribution developed for suppression of helium embrittlement. Three different preinjection treatments were adopted for changing the TiC distribution. Considerable degradation in creep rupture strength by helium occurred in solution-annealed specimens, although there was much less effect of other treatments which included aging prior to injection. The concentration of helium at grain boundaries and the promotion of precipitation by helium during injection were responsible for the degradation. Therefore, the presence of TiC precipitates before helium introduction will help prevent degradation. On the other hand, the rupture elongation was reduced by helium after all treatments, although helium trapping by TiC precipitates in the matrix was successfully achieved. Consequently, the combined use of several methods may be necessary for further suppression of helium embrittlement. (orig.)

  1. Preliminary creep and pillar closure data for shales

    International Nuclear Information System (INIS)

    Lomenick, T.F.; Russell, J.E.

    1987-10-01

    The results of fourteen laboratory creep tests on model pillars of four different shales are reported. Initial pillar stresses range from 6.9 MPa (1000 psi) to 69 MPa (10,000 psi) and temperatures range from ambient to 100 0 C. Laboratory response data are used to evaluate the parameters in the transient power-law pillar closure equation similar to that previously used for model pillars of rock salt. The response of the model pillars of shale shows many of the same characteristics as for rock salt. Deformation is enhanced by higher stresses and temperatures, although the shale pillars are not as sensitive to either stress or temperature as are pillars of rock salt. These test results must be considered very preliminary since they represent the initial, or scoping, phase of a comprehensive model pillar test program that will lead to the development and validation of creep laws for clay-rich rocks. 11 refs., 9 figs., 7 tabs

  2. Uni axial tensile graphite creep capsules with continuous strain registration

    International Nuclear Information System (INIS)

    Hausen, H.; Loelgen, R.; Cundy, M.

    1977-01-01

    Two irradiation devices are described for the in pile measurement of tensile irradiation creep of graphite. In each machine a single sample is maintained under a controlled load by a pneumatic bellows system. Irradiation creep is measured relative to unstressed reference shells which surround the stressed sample. This differential strain is detected by linear displacement transducers, and recorded automatically by the out of pile installation. Irradiation temperatures are in the 800 to 1100 0 C range, and the stresses up to 60% of the U.T.S. One machine has been specifically designed for a flux change experiment, other irradiation parameters remaining fixed. Temperature control is achieved through varying gas mixtures in control gas gaps. The paper details the design principles of the machines and gives an account of the cold and hot commissioning tests, with particular reference to the accuracy of the in pile measuring system. Finally, the early irradiation experience is evaluated

  3. A cycle combining method for creep fatigue analysis

    International Nuclear Information System (INIS)

    Debaene, J.P.; Permezel, P.

    1987-01-01

    In codes such as RCC-Mr (2) or code case N 47, rules are written against the creep fatigue damage. During the design phase, the order of succession of transients is not known. In that case, the codes require to take the order of events which leads to the maximum damage, but they don't give the detailed rules to perform it. The method we present here consists in building the totality of possible loading histories. For each loading history we calculate the creep fatigue damage V+W. The choice of the most severe loading history is done a posteriori. In practice, we are lead to uncouple the calculation of V and W. We proceed as follows: 1. Build all the loading histories able to masimize V. 2. For each of these loading histories, maximize W. 3. Choose a posteriori the most damaging loading history. (orig./GL)

  4. Creep behaviour of near-equiatomic nickel-titanium wires

    Energy Technology Data Exchange (ETDEWEB)

    Eker, Aysegul Akdogan; Kucukyildirim, Bedri Onur [Yildiz Technical Univ., Istanbul (Turkey). Mechanical Engineering Dept.; Sonmez, Deniz

    2013-02-01

    The creep behaviour of near-equiatomic (50.8 at.-% Ni) NiTi wire with a diameter of 0.49 mm is studied between 82 MPa and 127 MPa tensile stress as well as in a temperature range of 575 C to 650 C. For 600 C and between 82-107 MPa a stress exponent of n = 4.5 as well as for 82 MPa between 600-625 C an activation energy of Q = 300 kJ mol-1 have been found, these results have been compared with previous creep studies. In contrast to previous studies, this investigation has been performed with high stresses for thin NiTi wires. Moreover, fracture surfaces and ductility of wires have been investigated. The main reasons for the various results are discussed. (orig.)

  5. A review of experimental methods for determining residual creep life

    International Nuclear Information System (INIS)

    Bolton, C.J.

    1977-11-01

    Experimental methods available for determining how much creep life remains at a particular time in the high temperature service of a component are reviewed. After a brief consideration of the limitations of stress rupture extrapolation techniques, the application of post-exposure creep testing is considered. Ways of assessing the effect of microstructural degradation on residual life are then reviewed. It is pointed out that while this type of work will be useful for certain materials, there are other materials in which 'mechanical damage' such as cavitation will be more important. Cavitation measurement techniques are therefore reviewed. The report ends with a brief consideration of the use of crack growth measurements in assessing the residual life of cracked components. (author)

  6. A metallographic examination of structural degradation during creep-fatigue

    International Nuclear Information System (INIS)

    Hales, R.

    1979-07-01

    A series of specimens of T316 stainless steel, which had been tested under creep-fatigue conditions, has been examined by optical and scanning electron microscopy. The development of cavities which are associated with grain-boundary carbide precipitates has been recorded. These cavities increase in size and number with increasing hold time at peak tensile strain and cause the propagating fatigue crack to follow an intergranular path. At a strain range of +- 0.25% the dominant damage mechanism is due to creep damage when the tensile hold time is greater than one minute. The fatigue crack which causes final failure is nucleated at a stress raiser and it is possible that in a smooth specimen failure may occur without the nucleation of a fatigue crack at all but rather by ductile shearing. (author)

  7. Low-temperature creep of nanocrystalline titanium(IV) oxide

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, H.; Averback, R.S. (Dept. of Materials Sceince and Engineering, Univ. of Illinois, Urbana, IL (United States))

    1991-11-01

    This paper reports that nanocrystalline TiO[sub 2] with densities higher than 99% of rutile has been deformed in compression without fracture at temperatures between 600[degrees] and 800[degrees] C. The total strains exceed 0.6 at strain rates as high as 10[sup [minus]3] s[sup [minus]1]. The original average grain size of 40 nm increases during the creep deformation to final values in the range of 120 to 1000 nm depending on the temperature and total deformation. The stress exponent of the strain rate, n, is approximately 3 and the grain size dependence is d[sup [minus]q] with q in the range of 1 to 1.5. It is concluded that the creep deformation occurs by an interface reaction controlled mechanism.

  8. Inelastic analysis of Battelle-Columbus piping elbow creep test

    International Nuclear Information System (INIS)

    Dhalla, A.K.; Newman, S.Z.

    1979-01-01

    Analytical results are presented for room temperature and 593 deg. C creep bending deformation of a piping elbow structure tested at the Battelle-Columbus Laboratory. This analysis was performed in support of the International Piping Benchmark Problem Program being coordinated by ORNL. Results are presented for both simplified and refined structural models, and compared with test measurements reported by the Battelle-Columbus Laboratory. (author)

  9. Creep and fatigue of alloy 800 in helium

    International Nuclear Information System (INIS)

    Cook, R.H.

    1975-01-01

    Proposals for use of Alloy 800 as a H.T.R. boiler material have prompted studies of its creep and high temperature fatigue properties in impure helium with comparative tests in air. In impure helium, as expected in a H.T.R., reactions of potential importance are selective oxidation (of chromium, aluminium and titanium) and possibly carburisation from carbon monoxide or methane. In air, general oxidation will occur, possibly accompanied by nitridation. The effects of these reactions will depend on specimen geometry and the nature of the deformation. Two important possibilities are: (i) that environment affects the structure and properties of a surface zone of material undegoing uniform deformation (this may modify creep rate and crack nucleation); and (ii) that environment affects behaviour of a small region (e.g. at the root of a notch or ahead of a crack) in a specimen undergoing non-uniform deformation (this will modify crack growth and hence rupture life or fatigue endurance). This paper summarises experimental work demonstrating an influence of the above reactions on mechanical properties of austenitic steels and nickel-based alloys, drawing examples where possible from the limited data available on Alloy 800. Whilst nitridation and carburisation may simply increase creep resistance at the expense of ductility (and possibly of fatigue resistance), the effects of oxidation are complex. A high oxygen pressures (as in air) oxygen may reduce creep and fatigue resistance by promoting cavitation but formation of oxide in cracks can reduce their propagation rate. At low oxygen pressures, as expected in H.T.R. helium, oxygen enhanced cavitation is less likely, but selective oxidation along grain boundaries can sometimes assist crack nucleation. (author)

  10. Creep embrittlement of austenitic stainless steels with titanium addition

    International Nuclear Information System (INIS)

    Felsen, M.F.

    1983-04-01

    Some cold-worked austenitic stainless steels of the 316 type with titanium addition exhibit a low creep ductility and a notch sensitivity in the temperature range of 550 0 C to 750 0 C and for times to rupture from 10 to 10000 hours. It has been shown that this embrittlement increases highly with cold-work percentage, with solution annealing temperature, and depends on chemical composition because these factors can modify the difference of hardness between grains and grain boundaries

  11. Creep deformation of a soft magnetic iron-cobalt alloy

    Science.gov (United States)

    Fingers, R. T.; Coate, J. E.; Dowling, N. E.

    1999-04-01

    The U.S. Air Force is in the process of developing magnetic bearings, as well as an aircraft integrated power unit and an internal starter/generator for main propulsion engines. These developments are the driving force for the new emphasis on the development of high saturation, low loss magnets capable of maintaining structural integrity in high stress and high temperature environments. It is this combination of desired material characteristics that is the motivation of this effort to measure, model, and predict the creep behavior of such advanced magnetic materials. Hiperco® Alloy 50HS, manufactured by Carpenter Technology Corporation, is one of the leading candidates for these applications. Material specimens were subjected to a battery of mechanical tests in order to study and characterize their behaviors. Tensile tests provided stress versus strain behaviors that clearly indicated: a yield point, a heterogeneous deformation described as Lüders elongation, the Portevin-LeChatelier effect at elevated temperatures, and most often a section of homogeneous deformation that concluded with necking and fracture. Creep testing indicated three distinct types of behavior. Two types resembled a traditional response with primary, secondary, and tertiary stages; while the third type can be characterized by an abrupt increase in strain rate that acts as a transition from one steady-state behavior to another. The relationships between the tensile and creep responses are discussed. Analyses of the mechanical behavior include double linear regression of empirically modeled data, and constant strain rate testing to bridge the tensile and creep test parameters.

  12. Creep of cast Fe-36Al-2Ti alloy

    Czech Academy of Sciences Publication Activity Database

    Dobeš, Ferdinand; Kratochvíl, P.; Milička, Karel

    2006-01-01

    Roč. 14, 10-11 (2006), s. 1199-1203 ISSN 0966-9795. [EUROMAT 2005. Praha, 05.09.2005-08.09.2005] R&D Projects: GA ČR(CZ) GA106/05/0409 Institutional research plan: CEZ:AV0Z20410507 Keywords : iron aluminides, based on FeAl * creep * mechanical testing Subject RIV: JG - Metallurgy Impact factor: 1.943, year: 2006

  13. Study of the temperature dependence of the uniaxial creep property of similar material of new soft rock

    Science.gov (United States)

    Wang, Y. Y.; Wu, Y.; Fan, X. Y.; Zhang, J. L.; Guo, P.; Li, J. G.

    2017-11-01

    Using the experimental method, the experimental research of creep properties were conducted under different temperature ranging from 10°C to 60°C. The similar material of new soft rock consists of paraffin, which can obtain that the deformation contains the instantaneous elastic deformation and creep deformation through the uniaxial creep experimental results. And thus the increase of temperature has great influence on the creep characteristics of similar soft rock according to the creep curve of similar soft rock at 10°C to 60°C. With the increase of temperature, the slope of the stress-strain curve of similar soft rock is increasing, while the average of the creep modulus is decreasing, which means that the capacity of resist deformation is reduced. Therefore, the creeps law of high-temperature and short-time can be shown the creep phenomenon of low-temperature and long-time, and further shorten the creep experimental cycle.

  14. The influence of the grain boundary structure on diffusional creep

    International Nuclear Information System (INIS)

    Thorsen, P.A.

    1998-05-01

    An experiment was carried out to quantify the deformation in the diffusional creep domain. It was found that material had indisputably been deposited at grain boundaries in tension. A characterisation of 131 boundaries in terms of their misorientation was carried out and this was correlated to the observed deformation. Twin boundaries below a certain limit of deviation from an exact twin misorientation were totally inactive in the deformation. A large qualitative difference was found in the way general boundaries take part in the deformation. The experiments have taken place at Materials Research Department, Risoe National Laboratory at Roskilde. The present thesis has been submitted in partial fulfillment of the requirements for the Ph.D. degree in physics at the Niels Bohr Institute, University of Copenhagen. Besides the results of the creep experiment the thesis contains a description of the theoretical background to diffusional creep models. Also, the results from an investigation of helium bubble formation in an irradiated copper sample is included. (au)

  15. A knowledge based system for creep-fatigue assessment

    International Nuclear Information System (INIS)

    Holdsworth, S.R.

    1999-01-01

    A knowledge based system was developed in the BRITE-EURAM C-FAT project to store the material property information necessary to perform complex creep-fatigue assessments and to thereby improve the effectiveness of data retrieval for such purposes. The C-FAT KBS incorporates a multi-level database which is structured to contain not only 'reduced' deformation and fracture test data, but also to enable ready access to the derived parameter constants for the constitutive and model equations used in a range of assessment procedures. The data management scheme is reviewed. The C-FAT KBS also has a dynamic worked example module which allows the sensitivity of predicted lifetimes to material property input data to be evaluated by a number of procedures. Complex cycle creep-fatigue endurance predictions are particularly sensitive to the creep property data used in assessment, and this is demonstrated with reference to the results of a number of large single edge notched bend specimen feature tests performed on a 1CrMoV turbine casting steel at 550 C. (orig.)

  16. Short term creep rupture predictions for tantalum alloy T-111

    International Nuclear Information System (INIS)

    Stephens, J.J.

    1991-01-01

    A knowledge of the short term creep rupture behavior of Tantalum alloy T-111 is necessary to predict device integrity in the heat source section of Radioisotope Thermoelectric Generators (RTGs) at the end of service life, in the event of a fuel fire. High pressures exist in RTGs near the end of service life, these are caused by gas generation resulting from radioactive decay of the nuclear fuel. The internal pressure exerts a significant hoop stress on the T-111 alloy structural containment member. This paper analyses the short term creep behavior (rupture times up to ∼2x10 3 hrs.) of cold worked (CW) T-111 alloy, using the existing data of Stephenson (1967). Corellations for the time to rupture, time to 1% strain and minimum creep rate have been obtained from this data using multivariable linear regression analysis. These results are compared to other short term rupture data for T-111 alloy. Finally, at the stress/temperature levels relevant to the RTG fuel fire scenario near the end of service life, the rupture time correlation for T-111 alloy predicts a rupture time of approximately 100 hrs

  17. Comparison of methods for extrapolating breaking creep results

    International Nuclear Information System (INIS)

    Lehmann, Daniel.

    1980-06-01

    Among all the methods of extrapolation, the following have been selected: - parametric methods (Larson-Miller, Dorn, Manson-Haferd); - digital and parametric method (minimum commitment); - digital method (finite differences); - descriptive method (Givar). The Larson-Miller, Dorn and Manson-Haferd methods are commonly used for analyzing the breaking creep results of materials for which the master curves can be described simply. The other methods have been developed in order to analyze the breaking creep results of materials where the structural changes over time modify the creep behaviour. In each case the assessment of the parameters is achieved by the least squares method. These methods were compared with each other on two steels, namely: Z6 CND 17-12 (316) and Z4 CND 35-20 (800 alloy). The various analyses performed show that (a) the predictions made as from the different methods are in good agreement between each other when there is a sufficient number of experimental values and (b) the predictions of the breaking times in the case of the 800 alloy differ from one method to the next. This result is due to the limited sampling data and to the complex behaviour of this alloy, the properties of which change with ageing [fr

  18. Irradiation creep under 60 MeV alpha irradiation

    International Nuclear Information System (INIS)

    Reiley, T.C.; Shannon, R.H.; Auble, R.L.

    1980-01-01

    Accelerator-produced charged-particle beams have advantages over neutron irradiation for studying radiation effects in materials, the primary advantage being the ability to control precisely the experimental conditions and improve the accuracy in measuring effects of the irradiation. An apparatus has recently been built at ORNL to exploit this advantage in studying irradiation creep. These experiments employ a beam of 60 MeV alpha particles from the Oak Ridge Isochronous Cyclotron (ORIC). The experimental approach and capabilities of the apparatus are described. The damage cross section, including events associated with inelastic scattering and nuclear reactions, is estimated. The amount of helium that is introduced during the experiments through inelastic processes and through backscattering is reported. Based on the damage rate, the damage processes and the helium-to-dpa ratio, the degree to which fast reactor and fusion reactor conditions may be simulated is discussed. Recent experimental results on the irradiation creep of type 316 stainless steel are presented, and are compared to light ion results obtained elsewhere. These results include the stress and temperature dependence of the formation rate under irradiation. The results are discussed in relation to various irradiation creep mechanisms and to damage microstructure as it evolves during these experiments. (orig.)

  19. Bias factors for radiation creep, growth and swelling

    International Nuclear Information System (INIS)

    Nichols, F.A.

    1980-01-01

    Central to the present concepts of the origin of the radiation-induced creep, growth and swelling phenomena is the relative interaction of interstitials and vacancies with various sinks. Radiation-induced climb of dislocations, which figures in many theories of radiation creep and growth, requires the absorption of an excess of either vacancies or interstitials. On the other hand, radiation swelling requires the absorption of an excess of vacancies to effect void growth. These relative preferences are normally expressed in theoretical models by certain bias factors, or capture efficiencies, usually assumed to be constant. Several attempts have been made to estimate their magnitude theoretically but all are seen to involve errors or physically unrealistic assumptions. We present here a unified treatment in which these various bias factors are estimated in a self-consistent model which incorporates, for the first time, all the essential physics, i.e., defect production, interactions of both vacancies and interstitials with sinks and the presence of two types of sinks. We present quantitative evaluations for the SIPA creep model and for radiation swelling, and compare with previous estimates of these phenomena. (orig.)

  20. Development of a Generic Creep-Fatigue Life Prediction Model

    Science.gov (United States)

    Goswami, Tarun

    2002-01-01

    The objective of this research proposal is to further compile creep-fatigue data of steel alloys and superalloys used in military aircraft engines and/or rocket engines and to develop a statistical multivariate equation. The newly derived model will be a probabilistic fit to all the data compiled from various sources. Attempts will be made to procure the creep-fatigue data from NASA Glenn Research Center and other sources to further develop life prediction models for specific alloy groups. In a previous effort [1-3], a bank of creep-fatigue data has been compiled and tabulated under a range of known test parameters. These test parameters are called independent variables, namely; total strain range, strain rate, hold time, and temperature. The present research attempts to use these variables to develop a multivariate equation, which will be a probabilistic equation fitting a large database. The data predicted by the new model will be analyzed using the normal distribution fits, the closer the predicted lives are with the experimental lives (normal line 1 to 1 fit) the better the prediction. This will be evaluated in terms of a coefficient of correlation, R 2 as well. A multivariate equation developed earlier [3] has the following form, where S, R, T, and H have specific meaning discussed later.

  1. Ismetpasa and Destek regions; Creeping or accumulating strain

    Science.gov (United States)

    Yavasoglu, Hakan; Alkan, M. Nurullah; Aladogan, Kayhan; Ozulu, I. Murat; Ilci, Veli; Sahin, Murat; Tombus, F. Engin; Tiryakioglu, Ibrahim

    2016-04-01

    The North Anatolian Fault (NAF) is one of the most destructive fault system all over the world. In the last century, many devastating seismic event happened on it and its shear zone (NAFZ). Especially, after the 1999 Izmit and Duzce earthquakes, the earth science studies increase to save human life. To better understand the mechanism of the active fault system, tectonic stress and strain are important phenomena. According to elastic rebound theory, the locked active faults release the accumulated strain abruptly in four periods; interseismic, preseismic, coseismic and postseismic. In the literature, this phase is called the earthquake cycle. On the other hand, there is another scenario (aseismic deformation or creep) to release the strain without any remarkable seismic event. For the creep procedure, the important subject is threshold of the aseismic slip rate. If it is equal or larger than long-term slip rate, the destructive earthquakes will not occur along the fault which has aseismic slip rate. On the contrary, if the creep motion is lower than long-term slip rate along the fault, the fault has potential to produce moderate-to-large size earthquakes. In this study, the regions, Ismetpasa and Destek, have been studied to determine the aseismic deformation using GPS data. The first and second GPS campaigns have been evaluated with GAMIT/GLOBK software. Preliminary results of the project (slip-rate along the NAF in this region and aseismic deformation) will be presented.

  2. Bias factors for radiation creep, growth and swelling

    International Nuclear Information System (INIS)

    Nichols, F.A.

    1979-01-01

    Central to the present concepts of the origin of the radiation-induced creep, growth and swelling phenomena is the relative interaction of interstitials and vacancies with various sinks. Radiation-induced climb of dislocations, which figures in many theories of radiation creep and growth, requires the absorption of an excess of either vacancies or interstitials. On the other hand, radiation swelling requires the absorption of an excess of vacancies to affect void growth. These relative preferences are normally expressed in theoretical models by certain bias factors, or capture efficiencies, usually assumed to be constant. Several attempts have been made to estimate their magnitude theoretically but all are seen to involve errors or physically unrealistic assumptions. We present here a unified treatment in which these various bias factors are estimated in a self-consistent model which incorporates, for the first time, all the essential physics, i.e., defect production, interactions of both vacancies and interstitials with sinks and the presence of two types of sinks. We present quantitative evaluations for the SIPA creep model and for radiation swelling, and compare with previous estimates of these phenomena

  3. Onset of aseismic creep on major strike-slip faults

    KAUST Repository

    Çakir, Ziyadin

    2012-10-02

    Time series analysis of spaceborne synthetic aperture radar (SAR) data, GPS measurements, and fi eld observations reveal that the central section of the Izmit (Turkey) fault that slipped with a supershear rupture velocity in the A.D. 1999, Mw7.4, Izmit earthquake began creeping aseismically following the earthquake. Rapid initial postseismic afterslip decayed logarithmically with time and appears to have reached a steady rate comparable to the preearthquake full fault-crossing rate, suggesting that it may continue for decades and possibly until late in the earthquake cycle. If confi rmed by future monitoring, these observations identify postseismic afterslip as a mechanism for initiating creep behavior along strike-slip faults. Long-term afterslip and/or creep has signifi cant implications for earthquake cycle models, recurrence intervals of large earthquakes, and accordingly, seismic hazard estimation along mature strike-slip faults, in particular for Istanbul which is believed to lie adjacent to a seismic gap along the North Anatolian fault in the Sea of Marmara. © 2012 Geological Society of America.

  4. A Comparative Study on Creep Behavior of Wood Flour-Polypropylene Composite, Medium Density Fiberboard (MDF and Particleboard

    Directory of Open Access Journals (Sweden)

    J. Nikrai

    2009-12-01

    Full Text Available The creep/recovery behavior of wood flour-polypropylene was compared with medium density fiberboard (MDF and particleboard. For this purpose, wood flour-polypropylene composites (with and without compatibilizerwere manufactured by using a laboratory twin-screw extruder. The MDF and particleboard panels were obtained from local producers. Short term flexural creep tests at 30% of ultimate bending load were performed by using flexural creep equipment. The total time to complete every test was 120 min (60 min creep and 60 min recovery. Also Findley creep model was used for the prediction of creep behavior of the materials under study. The results showed that fractional deflection and relative creep in wood flour-polypropylene composites are higher than MDF and particleboard whereas MDF and particleboard exhibited higher percent recovery rather than wood flour-polypropylene composite. Creep modulus at the first phase of creep in wood flour-polypropylene composite was higher than MDF and particleboard but more decreases were observed for creep modulus of wood-plastic composite at the end of creep phase. Coupling agent (MAPP improved creep/recovery behavior of wood flour-polypropylene composite. Also Findley creep model predicted the creep behavior of studied materials very well.

  5. The microstructure and impression creep behavior of cast Mg–4Sn–4Ca alloy

    Energy Technology Data Exchange (ETDEWEB)

    Khalilpour, Hamid, E-mail: Ha.Khalilpoorster@gmail.com [Shahid Rajaee Teacher Training University, Faculty of Mechanical Engineering, Lavizan, Tehran (Iran, Islamic Republic of); Mahdi Miresmaeili, Seyed, E-mail: s_m_miresmaeily@yahoo.com [Shahid Rajaee Teacher Training University, Faculty of Mechanical Engineering, Lavizan, Tehran (Iran, Islamic Republic of); Baghani, Amir, E-mail: amir-baghani@uiowa.edu [University of Iowa, Department of Mechanical and Industrial Engineering, Iowa City, IA (United States)

    2016-01-15

    Because of low creep properties of magnesium–aluminum alloys, magnesium–tin alloys have received much attention in applications where high mechanical properties in high temperatures required. In this study creep properties of Mg–4Sn–4Ca alloy were investigated by the aim of impression creep test, scanning electron microscopy, energy dispersion spectrometry and X-ray diffraction analysis. The impression creep tests were carried out under different shear modulus normalized stress at high temperatures. According to the measured stress exponent values and activation energies the climb-controlled dislocation creep was determined as the dominant mechanism. The creep resistance of this alloy was related to the presence of Ca–Mg–Sn and Mg{sub 2}Ca phases which are distributed uniformly in the matrix and exhibit high thermal stability.

  6. The effect of pre-aging on the creep behaviour of type 321 stainless steel

    International Nuclear Information System (INIS)

    Snowden, K.U.; Stathers, P.A.; Hughes, D.S.

    1983-01-01

    An investigation was made of the influence of prior thermal treatment on the creep behaviour and microstructure of type 321 stainless steel. The material was pre-aged at 750 deg C in vacuum for periods up to approx. 10 3 hours and subsequently creep tested in air at 650 deg C and a stress of 200 MPa. Pre-aging increased the creep rate and the ductility, and decreased the time to failure and the activation energy for creep. Over the aging period examined, the increase in creep rate was proportional to (aging time)sup(0.61). Electron microscopy suggested that the increased creep rate was associated with the growth of precipitates at triple junctions, along grain boundaries and within grains. (author)

  7. Optimum tungsten content in high strength 9 to 12% chromium containing creep resistant steels

    International Nuclear Information System (INIS)

    Hasegawa, Y.; Muraki, T.; Mimura, H.

    2000-01-01

    Tungsten containing ferritic creep resistant steels are the candidate materials for ultra-super-critical fossil power plant because of their high creep rupture strength. But the strengthening mechanisms by tungsten addition have not yet been completely studied. In this report, creep rupture time and creep strain rate measurement decided the optimum tungsten content in 9 to 12% chromium ferritic steels. The precipitation behavior of Laves phase and the precise discussion of creep strain rate analyses explain the contribution of Laves phase at the lath boundary and the contribution of tungsten in solid solution. P92 contains the optimum amount of tungsten and chromium, 1.8 mass% and 9 mass% respectively judging from the creep rupture strength point of view. (orig.)

  8. Secondary creep of porous metal supports for solid oxide fuel cells by a CDM approach

    DEFF Research Database (Denmark)

    Esposito, L.; Boccaccini, D. N.; Pucillo, G. P.

    2017-01-01

    The creep behaviour of porous iron-chromium alloy used in solid oxide fuel cells (SOFCs) becomes relevant under SOFC operating temperatures. In this paper, the secondary creep stage of infiltrated and non-infiltrated porous metal supports (MS) was investigated and theoretically modelled by a cont......The creep behaviour of porous iron-chromium alloy used in solid oxide fuel cells (SOFCs) becomes relevant under SOFC operating temperatures. In this paper, the secondary creep stage of infiltrated and non-infiltrated porous metal supports (MS) was investigated and theoretically modelled...... as function of temperature, determined by the high temperature impulse excitation technique, was directly used to account for the porosity and the related effective stress acting during the creep tests. The proposed creep rate formulation was used to extend the Crofer® 22 APU Monkman-Grant diagram...

  9. Stress Distribution in Layered Elastic Creeping Array with a Vertical Cylindrical Shaft

    Directory of Open Access Journals (Sweden)

    Bobyleva Tatiana

    2017-01-01

    Full Text Available Construction should be taking into account the influence of time factor on the stability of the structures. In the paper hereditary creep and homogenization theories are used to determine stresses in the layered elastic creeping array with a vertical shaft. Volterra correspondence principle was applied. As a result, the reduction of a time-dependent elastic creeping problem to a corresponding elastic problem became possible. The method proposes a way to determine average (effective elastic creeping properties and homogenized stress field from known properties of the layers’ components. Creep kernels are of a convolution type and are taken in the exponential form. The problem of heterogeneous elastic creeping environment is reduced to a problem of homogeneous transversely isotropic medium. Different boundary conditions on the cylindrical shaft’s surface were considered. An analytical solution was obtained. These explicit expressions can be useful for the necessary calculations in the construction practice.

  10. Comparison of stress-based and strain-based creep failure criteria for severe accident analysis

    International Nuclear Information System (INIS)

    Chavez, S.A.; Kelly, D.L.; Witt, R.J.; Stirn, D.P.

    1995-01-01

    We conducted a parametic analysis of stress-based and strain-based creep failure criteria to determine if there is a significant difference between the two criteria for SA533B vessel steel under severe accident conditions. Parametric variables include debris composition, system pressure, and creep strain histories derived from different testing programs and mathematically fit, with and without tertiary creep. Results indicate significant differences between the two criteria. Stress gradient plays an important role in determining which criterion will predict failure first. Creep failure was not very sensitive to different creep strain histories, except near the transition temperature of the vessel steel (900K to 1000K). Statistical analyses of creep failure data of four independent sources indicate that these data may be pooled, with a spline point at 1000K. We found the Manson-Haferd parameter to have better failure predictive capability than the Larson-Miller parameter for the data studied. (orig.)

  11. Creep crack growth predictions in INCO 718 using a continuum damage model

    Science.gov (United States)

    Walker, K. P.; Wilson, D. A.

    1985-01-01

    Creep crack growth tests have been carried out in compact type specimens of INCO 718 at 1200 F (649 C). Theoretical creep crack growth predictions have been carried out by incorporating a unified viscoplastic constitutive model and a continuum damage model into the ARAQUS nonlinear finite element program. Material constants for both the viscoplastic model and the creep continuum damage model were determined from tests carried out on uniaxial bar specimens of INCO 718 at 1200 F (649 C). A comparison of the theoretical creep crack growth rates obtained from the finite element predictions with the experimentally observed creep crack growth rates indicates that the viscoplastic/continuum damage model can be used to successfully predict creep crack growth in compact type specimens using material constants obtained from uniaxial bar specimens of INCO 718 at 1200 F (649 C).

  12. Stability analysis of quasi-brittle materials - creep under multiaxial loading

    Science.gov (United States)

    Challamel, Noël; Lanos, Christophe; Casandjian, Charles

    2006-03-01

    The aim of this paper is to develop a simple time-dependent Continuum Damage Mechanics model applied to quasi-brittle materials such as rock or concrete. The three-dimensional constitutive visco-damage model describes phenomena like relaxation, creep and rate-dependent loading using a unified framework. A material stability analysis devoted to creep tests highlights a general creep stress stability domain. This convex domain is connected to the property of the associated time-independent Continuum Damage Mechanics model. More particularly, the boundary of this domain in the creep stress space coincides with the invertibility condition of the constitutive matrix considering infinitely slow loading. Phenomenon as creep failure under high-sustained load is explained quite simply within stability theory. Creep failure appears as the manifestation of a saddle-node bifurcation phenomenon.

  13. Effects of composition on the in-reactor creep of AISI 316

    International Nuclear Information System (INIS)

    Bates, J.F.; Gilbert, E.R.

    1979-08-01

    In-reactor tests designed to provide information on the relationship between compositional variations and irradiation-induced swelling and creep have achieved an exposure of 4.6 x 10 22 n/cm 2 (E > 0.1 MeV) at 450 0 C. Postirradiation diametral measurements of pressurized tube specimens have indicated that irradiation-induced creep of 316 stainless steel can be modified by compositional variations of minor alloying elements. There is a general trend for specimens with higher swelling to exhibit higher creep. Silicon, phosphorus and molybdenum all retard in-reactor creep and inhibit irradiation-induced swelling as well. However, the relationship between creep and swelling is strongly composition dependent. The data suggest that carbon and nitrogen act synergistically the major influence being the nitrogen concentration. The irradiation-induced creep is insensitive to cobalt variations to the fluences investigated

  14. Effects of composition on the in-reactor creep of AISI 316

    International Nuclear Information System (INIS)

    Bates, J.F.; Gilbert, E.R.

    1980-01-01

    Pre- and postirradiation measurements of pressurized tube specimens irradiated at 450/degree/C to 4.6*10/sup 22/ n/cm/sup 2/(E>0.1 MeV) have indicated that increases in the solute concentrations of silicon, phosphorus, and molybdenum retard irradiation creep. The data suggest that carbon and nitrogen act synergistically with the major influence on creep being the nitrogen concentration. Irradiation-induced creep is insensitive to cobalt variations. There is a trend for specimens with higher swelling to exhibit higher creep. As the shear modulus increases, irradiation creep also increases. This shear modulus correlation is opposite to one observed for thermal creep deformation. 8 refs

  15. SEPA (Service d'etudes, de Procedes et Analyses)

    International Nuclear Information System (INIS)

    2017-01-01

    The SEPA (Service d'etudes, de Procedes et Analyses), is an engineering department specializing in the analysis and processing of uranium ore. It comes from a long tradition of mining in France that began sixty-five years ago with the French Atomic Energy Commission (CEA) and that has been carried on by COGEMA and then Areva. SEPA brings a combination of experience and excellence to its activities thanks to its multidisciplinary staff (mineralogists, chemists, mechanical engineers, instrumentation specialists...), who come from diverse cultural backgrounds. Today, the SEPA draws on its wealth of know-how and expertise to devise and develop new methods for processing and valorizing ores everywhere in the world. Its mission is to: - Develop and conduct laboratory tests on methods for processing uranium and other valuable elements such as molybdenum, vanadium, rare earths, niobium, tantalum and thorium; - Analyze ores obtained during prospecting at locations all over the world; -Serve as an advisor in the commissioning of Areva industrial units and ore processing plants; -Perform environmental analyses during the full period of mining operations; -Conduct audits and provide advice on processes and analysis methods; -Carry out research and development in all aspects of minerals treatment (including the filing of patents). The SEPA combines experience, skills and a global approach to technologies used in ore processing. Its role is to continually improve the processes for extracting, processing and valorizing ores while protecting the environment

  16. Constitutive model of creep in polycrystalline halite based on workhardening and recovery

    International Nuclear Information System (INIS)

    Munson, D.E.

    1993-01-01

    A multimechanism constitutive model of creep has been developed which incorporates the workhardening and recovery transient creep behavior. This model has been applied to the creep of polycrystalline halite. The specific application of the model is in the calculation of the closure of underground rooms in layered salt deposits. Through the use of finite element calculations, this model, with appropriate laboratory material parameters and a Tresca flow potential, has predicted the measured closure of a number of large in situ experimental rooms

  17. Irradiation creep of solution annealed and cold worked 316 stainless steel

    International Nuclear Information System (INIS)

    Boutard, J.L.; Carteret, Y.; Cauvin, R.; Maillard, A.; Guerin, Y.

    1983-01-01

    Irradiation creep strains obtained in-pile on S.A. and C.W. 316 show a linear creep-swelling correlation, the slope of which is rather insensitive to chemical composition and elements in solid solution. The variation of SIPA component resulting only from the evolution of dislocation density and void growth cannot explain such an empirical correlation. The I-creep term has, on the other hand, the right temperature dependence and order of magnitude. (author)

  18. Creep of high-strength Mg-Ni-Y-RE alloys

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel; Peréz, P.; Dobeš, Ferdinand; Garcés, G.; Adeva, P.

    510-511, Sp. Iss. (2009), s. 377-381 ISSN 0921-5093. [International Conference of Creep and Fracture of Engineering Materials and Structures /11./. Bad Berneck, 04.05.2008-09.05.2008] R&D Projects: GA ČR GA106/06/1354 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * creep * Back stress concept * creep mechanisms Subject RIV: JG - Metallurgy Impact factor: 1.901, year: 2009

  19. A SIPA-based theory of irradiation creep in the low swelling rate regime

    International Nuclear Information System (INIS)

    Garner, F.A.; Woo, C.H.

    1991-11-01

    A model is presented which describes the major facets of the relationships between irradiation creep, void swelling and applied stress. The increasing degree of anisotropy in distribution of dislocation Burger's vectors with stress level plays a major role in this model. Although bcc metals are known to creep and swell at lower rates than fcc metals, it is predicted that the creep-swelling coupling coefficient is actually larger

  20. Review of Creep Cavitation and Rupture of Low Cr Alloy and its Weldment

    OpenAIRE

    Xu, Qihua; Xu, Qiang; Pang, Yongxin; Short, Michael

    2013-01-01

    This paper presents a review of creep cavitation and rupture of low Cr alloy and its weldment, particular in the heat-affected zone (HAZ). Creep damage is one of the serious problems for the high temperature industry. One of the computational approaches is continuum damage mechanics which has been developed and applied complementary to the experimental approach and assists in the safe operation. However, the existing creep damage constitutive equations are not developed specifically for low s...

  1. Preliminary analysing of experimental data for the development of high Cr Alloy Creep damage Constitutive Equations

    OpenAIRE

    An, Lili; Xu, Qiang; Xu, Donglai; Lu, Zhongyu

    2012-01-01

    This conference paper presents the current research of preliminary analysing of experimental data for the development of high Cr Alloy Creep damage Constitutive Equations (such as P91 alloy). Firstly, it briefly introduces the background of general creep deformation, rupture and continuum damage mechanics. Secondly, it illustrates the constitutive equations used for P91 alloy or its weldment, especially of the form and deficiencies of two kinds of most widely used typical creep damage constit...

  2. Creep of crystals: High-temperature deformation processes in metals, ceramics and minerals

    Science.gov (United States)

    Poirier, J. P.

    An introductory text describing high-temperature deformation processes in metals, ceramics, and minerals is presented. Among the specific topics discussed are: the mechanical aspects of crystal deformation; lattice defects; and phenomenological and thermodynamical analysis of quasi-steady-state creep. Consideration is also given to: dislocation creep models; the effect of hydrostatic pressure on deformation; creep polygonization; and dynamic recrystallization. The status of experimental techniques for the study of transformation plasticity in crystals is also discussed.

  3. Microstructural evolution and creep behaviour of the modified 9% Cr steel with boron and cobalt

    International Nuclear Information System (INIS)

    Nowakowski, P.; Spiradek-Hahn, K.; Brabetz, M.; Zeiler, G.

    1998-01-01

    In the present study the microstructural evolution of the new 9% Cr with boron and cobalt is shown during creep at 650 o C. The minimum creep rates of the new alloy are significantly lower than those of conventional 12 % Cr steel. This is due to the high stability of M 23 C 6 precipitates with respect to the coarsening and the preservation of high dislocation density in the course of creep exposure. (author)

  4. Comparison of Cu and Ti-52A1 in creep at the same homologous temperature and minimum creep rate

    Czech Academy of Sciences Publication Activity Database

    Orlová, Alena

    2001-01-01

    Roč. 9, - (2001), s. 529-534 ISSN 0966-9795 R&D Projects: GA ČR GA106/98/1369; GA AV ČR IBS2041001 Institutional research plan: CEZ:AV0Z2041904 Keywords : titanium aluminides based on TiAl * creep * dislocation geometry and arrangement Subject RIV: JG - Metallurgy Impact factor: 1.239, year: 2001

  5. Carbon dioxide and climate

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-01

    Scientific and public interest in greenhouse gases, climate warming, and global change virtually exploded in 1988. The Department's focused research on atmospheric CO{sub 2} contributed sound and timely scientific information to the many questions produced by the groundswell of interest and concern. Research projects summarized in this document provided the data base that made timely responses possible, and the contributions from participating scientists are genuinely appreciated. In the past year, the core CO{sub 2} research has continued to improve the scientific knowledge needed to project future atmospheric CO{sub 2} concentrations, to estimate climate sensitivity, and to assess the responses of vegetation to rising concentrations of CO{sub 2} and to climate change. The Carbon Dioxide Research Program's goal is to develop sound scientific information for policy formulation and governmental action in response to changes of atmospheric CO{sub 2}. The Program Summary describes projects funded by the Carbon Dioxide Research Program during FY 1990 and gives a brief overview of objectives, organization, and accomplishments.

  6. Constitutive model for the low temperature creep of salt (with application to WIPP)

    International Nuclear Information System (INIS)

    Munson, D.E.; Dawson, P.R.

    1979-10-01

    While numerous constitutive models have been proposed for the low temperature creep of salt, this work is the first to develop such a model within the framework of rate controlling mechanisms and the deformation-mechanism map. Use of this framework permitted unfolding of the rather complicated low temperature steady-state creep behavior into three simpler responses involving separate regimes with individual controlling mechanisms. The observed total creep rate obeys the rules of additive processes. The creep model incorporates primary (transient) creep as a simple two parameter modificaton to the steady-state creep equations. Application of the model is through a formulation into proper stress and strain measures for use in a large strain finite element code. Extensive analysis of available low-temperature triaxial creep data produced the appropriate material parameters, including activation energies and stress dependencies for the separate regimes. Material variations were observed to produce changes in absolute creep rate, without change in controlling mechanism. Numerous calculations demonstrate the adequacy of the model and numerical method to simulate the results of triaxial creep experiments on Southeastern New Mexico salt from the horizons proposed for the Waste Isolation Pilot Plant

  7. The transient creep of vapor deposited Ti-6Al-4V

    International Nuclear Information System (INIS)

    Warren, J.; Wadley, H.N.G.

    1996-01-01

    Titanium matrix composites can be synthesized by the consolidation of ceramic fibers (for example, alumina and silicon carbide monofilaments) coated with titanium alloy deposited on the fiber by physical vapor deposition (PVD). Consolidation involves deformation of the matrix coating by both transient and steady-state creep. In a recent paper the mechanisms responsible for steady-state creep in PVD Ti-6Al-4V, between 600 and 900 C, were determined. The analysis of the data first presented has been extended here to consider the transient creep behavior of the material and identify an analogous constitutive law for use in simulating the transient creep contribution to consolidation

  8. Relaxation of Shot-Peened Residual Stresses Under Creep Loading (Preprint)

    National Research Council Canada - National Science Library

    Buchanan, Dennis J; John, Reji; Brockman, Robert A

    2008-01-01

    .... Compressive residual stresses retard initiation and growth of fatigue cracks. During the component loading history, loading, or during elevated temperature static loading, such as thermal exposure and creep...

  9. Examination of the creep behaviour of ceramic fuel elements under neutron irradiation

    International Nuclear Information System (INIS)

    Brucklacher, D.

    1978-01-01

    This paper examines the creeping of UO 2 , UO 2 -PuO 2 and UN under neutron irradiation. It starts with the experimental results about the relation between the thermal creep rate and the load, the temperature, as well as characteristic material values, stoichiometry, grain size and porosity. These correlation are first qualitatively discussed and then compared with the statements of actual quantitative equations. From the models and theories on which these equations are based a modified Nabarro-Heering-equation results for the correlation between the creep rate of ceramic fuels, stress, temperature and the fission rate. In the experimental part of the examination, length-changes of creep samples of UO 2 , (U,Pu)O 2 and UN were measured in specially developed irradiation creep casings in different reactors. The measuring data were corrected and evaluated considering the thermal expansion effects, irregular temperature distribution and swelling effects in such a way that the dependences of the creep rate of UO 2 , UO 2 -PuO 2 and UN under irradiation on stress, temperature, fission rate, burn-up and porosity is obtained. It shows that creeping of fuels under irradiation at high temperatures is equivalent to thermally activated creeping, while at low temperature the creep rate induced by irradiation is much higher than the condition without irradiation. The increment of oxidic nuclear fuels is greater than in UN, the stress dependence on low burn-up is proportional in both cases, and the influence of temperature is quite small. (orig.) [de

  10. Application Of Elastic Perfectly Plastic Cyclic Analysis To Assessment Of Creep Strain

    Energy Technology Data Exchange (ETDEWEB)

    Carter, Peter [Stress Engineering Services Inc.; Jetter, Robert I [Consultant; Sham, Sam [ORNL

    2012-01-01

    A cyclic elastic-perfectly plastic analysis method is proposed which provides a conservative estimate to cyclic creep strain accumulation within the ratchet boundary. The method is to check for ratcheting based on an elastic-perfectly material with a temperature-dependent pseudo yield stress defined by temperature, time and stress to give 1% creep strain. It does not require stress classification and is also applicable to a full range of temperature above and below the creep regime. This simplified method could be used as a rapid screening calculation, with full time-dependent creep analysis used if necessary.

  11. Mechanisms of High Temperature/Low Stress Creep of Ni-Based Superalloy Single Crystals

    Energy Technology Data Exchange (ETDEWEB)

    Michael J. Mills

    2009-03-05

    Cast nickel-based superalloys are used for blades in land-based, energy conversion and powerplant applications, as well as in aircraft gas turbines operating at temperatures up to 1100 C, where creep is one of the life-limiting factors. Creep of superalloy single crystals has been extensively studied over the last several decades. Surprisingly, only recently has work focused specifically on the dislocation mechanisms that govern high temperature and low stress creep. Nevertheless, the perpetual goal of better engine efficiency demands that the creep mechanisms operative in this regime be fully understood in order to develop alloys and microstructures with improved high temperature capability. At present, the micro-mechanisms controlling creep before and after rafting (the microstructure evolution typical of high temperature creep) has occurred have yet to be identified and modeled, particularly for [001] oriented single crystals. This crystal orientation is most interesting technologically since it exhibits the highest creep strength. The major goal of the program entitled ''Mechanisms of High Temperature/Low Stress Creep of Ni-Based Superalloy Single Crystals'' (DOE Grant DE-FG02-04ER46137) has been to elucidate these creep mechanisms in cast nickel-based superalloys. We have utilized a combination of detailed microstructure and dislocation substructure analysis combined with the development of a novel phase-field model for microstructure evolution.

  12. Mechanisms Governing the Creep Behavior of High Temperature Alloys for Generation IV Nuclear Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Vasudevan, Vijay [Univ. of Cincinnati, OH (United States); Carroll, Laura [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-04-06

    This research project, which includes collaborators from INL and ORNL, focuses on the study of alloy 617 and alloy 800H that are candidates for applications as intermediate heat exchangers in GEN IV nuclear reactors, with an emphasis on the effects of grain size, grain boundaries and second phases on the creep properties; the mechanisms of dislocation creep, diffusional creep and cavitation; the onset of tertiary creep; and theoretical modeling for long-term predictions of materials behavior and for high temperature alloy design.

  13. Modification and Performance Evaluation of a Low Cost Electro-Mechanically Operated Creep Testing Machine

    Directory of Open Access Journals (Sweden)

    John J. MOMOH

    2010-12-01

    Full Text Available Existing mechanically operated tensile and creep testing machine was modified to a low cost, electro-mechanically operated creep testing machine capable of determining the creep properties of aluminum, lead and thermoplastic materials as a function of applied stress, time and temperature. The modification of the testing machine was necessitated by having an electro-mechanically operated creep testing machine as a demonstration model ideal for use and laboratory demonstrations, which will provide an economical means of performing standard creep experiments. The experimental result is a more comprehensive understanding of the laboratory experience, as the technology behind the creep testing machine, the test methodology and the response of materials loaded during experiment are explored. The machine provides a low cost solution for Mechanics of Materials laboratories interested in creep testing experiment and demonstration but not capable of funding the acquisition of commercially available creep testing machines. Creep curves of strain versus time on a thermoplastic material were plotted at a stress level of 1.95MPa, 3.25MPa and 4.55MPa and temperature of 20oC, 40oC and 60oC respectively. The machine is satisfactory since it is always ready for operation at any given time.

  14. Vortex creep and the internal temperature of neutron stars. I - General theory

    Science.gov (United States)

    Alpar, M. A.; Pines, D.; Anderson, P. W.; Shaham, J.

    1984-01-01

    The theory of a neutron star superfluid coupled to normal matter via thermal creep against pinning forces is developed in some detail. General equations of motion for a pinned rotating superfluid and their form for vortex creep are given. Steady state creep and the way in which the system approaches the steady state are discussed. The developed formalism is applied to the postglitch relaxation of a pulsar, and detailed models are developed which permit explicit calculation of the postglitch response. The energy dissipation associated with creep and glitches is considered.

  15. Microstructure evolution and deformation features of AZ31 Mg-alloy during creep

    International Nuclear Information System (INIS)

    Tian Sugui; Wang Ling; Sohn, Keun Yong; Kim, Kyung Hyun; Xu Yongbo; Hu Zhuangqi

    2006-01-01

    By means of the measurement of the creep curve and the observation of SEM and transmission electron microscope (TEM), an investigation has been made into the microstructure evolution and deformation features of AZ31 Mg-alloy during high temperature creep. Results show that the deformation features of the alloy in the primary stage of creep are that significant amount of dislocation slips are activated on basal and non-basal planes, then these ones are concentrated into the dislocation cells or walls as creep goes on. At the same time, twinning occurs as an additional deformation mechanism in the role of the compatibility stress. During steady state creep, the dislocation cells are transformed into the subgrains, then, the protrusion and coalition of the sub-boundaries results in the occurrence of dynamic recovery (DRV). After the dynamic recrystallization (DRX), the multiple slips in the grain interiors are considered to be the main deformed mechanism in the later stage of the steady state creep. An obvious feature of creep entering the tertiary stage is that the cracks appear on the locations of the triple junction. As creep continues, the cracks are viscous expanded along the grain boundaries; this is taken for being the fracture mechanism of the alloy crept to failure. The multiple slips in the grain interiors and the cracks expanded viscous along the grain boundary occur in whole of specimens, that, together with the twins and dynamic recrystallization, is responsible for the rapid increase of the strain rate in the later stage during creep

  16. Survey of creep properties of copper intended for nuclear waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Andersson-Oestling, Henrik C.M. (Swerea KIMAB AB, Stockholm (Sweden)); Sandstroem, Rolf (Materials Science and Engineering, School of Industrial Engineering and Management, Royal Inst. of Technology (KTH), Stockholm (Sweden))

    2009-12-15

    Creep in copper for application in canisters for nuclear waste disposal is surveyed. The importance of phosphorus doping to obtain adequate properties is demonstrated experimentally as well as explained theoretically. Creep tests results for electron beam and friction stir welds are compared. The latter type of welds has properties that are close to those of parent metal. The relation between slow strain rate tensile and creep is described. Fundamental constitutive equations are presented that are suitable for finite element modelling. These equations are used to simulate creep deformation in canisters

  17. A Numerical Procedure to Obtain the Creep Parameters of the Thermal Barrier Coating

    Directory of Open Access Journals (Sweden)

    Shifeng Wen

    2014-05-01

    Full Text Available Three-point bending creep test was used to understand the creep behavior of typical thin film/substrate systems—thermal barrier coating (TBC systems. Firstly, a simplified model, which does not consider the local effect, has been set up to get an analytical relationship. The important result is that creep stress exponent of materials is equal to the creep load exponent of the steady-state deflection rate of BC specimens. Secondly, in order to consider the local effect of bending, the finite element method (FEM has been carried out. FEM calculation shows that there is a steady stage of the creep deflection under a constant applied load. And the exponent of the steady-state creep deflection rate to the applied load is found to be equal to the creep stress exponent of materials. The creep constant of the materials can be obtained by a set of trials with assumed creep constants of materials and can be finally determined by the best fit method. Finally, the finite element results show that the influences of the friction, the thickness of TBCs, and the modulus ratio of TBC to the substrate on stress distribution are important.

  18. Technique for measuring irradiation creep in polycrystalline SiC fibers

    Energy Technology Data Exchange (ETDEWEB)

    Youngblood, G.E.; Hamilton, M.L.; Jones, R.H. [Pacific Northwest National Lab., Richland, WA (United States)

    1996-10-01

    A bend stress relaxation (BSR) test has been designed to examine irradiation enhanced creep in polycrystalline SiC fibers being considered for fiber reinforcement in SiC/SiC composite. Thermal creep results on Nicalon-CG and Hi-Nicalon were shown to be consistent with previously published data with Hi-Nicalon showing about a 100{degrees}C improvement in creep resistance. Preliminary data was also obtained on Nicalon-S that demonstrated that its creep resistance is greater than that of Hi-Nicalon.

  19. Microstructural changes during creep and life assessment of Mod.9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Sawada, Kota; Maruyama, Kouichi; Komine, Ryuji; Nagae, Yuji.

    1997-01-01

    Several microstructural changes take place in a material during the course of creep. These changes can be a measure of creep life. In this paper, microstructural changes in Mod.9Cr-1Mo steel were studied and it was examined which is a good measure of creep life. Microscopic structural changes, such as void growth, lath structure uniformly oriented to the tensile axis and elongation of grains, are evident only in the necked portion of ruptured specimens. These macroscopic structural changes are not useful for creep life assessment. Lath width increases and dislocation density within lath decreases with increasing creep duration. These changes in dislocation substructure start in the early stage of creep life, and cause the increase of strain rate in the tertiary creep stage. The lath width and the dislocation density reach a saturated value before rupture. The saturated values are independent of temperature, and uniquely related to creep stress normalized by shear modulus. The extent of these microstructural changes are greater at lower stresses under which the material is practically used. These facts suggest that the lath width and the dislocation density within lath can be a useful measure of creep life. Hardness of crept specimens is closely related to the lath width and the dislocation density within lath. The changes of these microstructural features can be evaluated by the measurement of hardness. (author)

  20. Estimation of crack growth in the creep range during plastic cyclic loading

    International Nuclear Information System (INIS)

    Kullik, M.; Maile, K.

    1990-01-01

    Crack growth investigations were performed on the creep-resistant steel 13 CrMo 4 4 in the fatigue and the creep fatigue regime, especially regarding the influence of creep damage on crack growth. To this effect, 2% creep strain was applied to the material at a temperature of 560deg C. The crack propagation rate was determined as a functionof the specimen shape, temperature, test frequency and hold times. In the case of compact tension (CT-)specimens, creep pretreatment does not affect crack growth. For center-cracked tension (CCT-)specimens, however, the creep pretreatment results in a considerable increase in the crack propagation rate. Hold times of 90 minutes at maximum loading cause an increase in da/dN due to further cavity nucleation. The hold time at which cavity nucleation might occur is evaluated. The dependency on frequency of crack growth may be evaluated by means of a linear superposition of creep and fatigue crack growth. The transition frequency above which pure fatigue crack growth occurs is calculated and the regimes of fatigue, creep and creep-fatigue interaction with environmental influences are characterized. (orig.)