WorldWideScience

Sample records for dioxanes

  1. Biodegradation of 1,4-Dioxane

    Science.gov (United States)

    2007-08-01

    widely used as solvents, pesticides , gasoline additives, and a host of other applications. Most recently, the solvent stabilizer 1,4-dioxane has...the Stringfellow FBRs were sent to us to attempt to enrich native 1,4-dioxane degrading microorganisms . For the initial enrichment of bacterial...63:4216-4222. Steffan, R. J., Y. Farhan, C. W. Condee, and S. Drew. 2003. Bioremediation at a New Jersey Site Using Propane-Oxidizing Bacteria

  2. Studies on Metabolism of 1,4-Dioxane

    Science.gov (United States)

    2010-03-01

    likely products of dioxane metabolism-2-hydroxyethoxyacetic acid (HEM or 13- hydroxyethoxyacetic acid ) and 1 ,4-dioxan-2-one (or dioxanone...Mar 10 (2) Hoch-Ligeti and coworkers (Hoch-Ligeti et al. 1974) originally proposed that dioxane was metabolized to oxalic acid by way of diglycolic... acid . This proposal was based upon chemical oxidation experiments on dioxane using nitric acid originally conducted by Fairley and coworkers (Fairley

  3. New Developments in 1,4 Dioxane Site Management

    Science.gov (United States)

    2016-11-01

    developed biomarkers to assess aerobic 1,4-dioxane degradation because it may be an important contributor to site-specific natural attenuation capacity...survey corroborate the results of the lab-based research showing that 1,4-dioxane degradation is favored under aerobic conditions but is inhibited by...oxidative attack. In situ oxidation technologies (e.g., chemical oxidation, enhanced aerobic biodegradation) should degrade 1,4-dioxane but each has

  4. [Extraction of lambda-cyhalothrin from aqueous dioxan solutions].

    Science.gov (United States)

    Shormanov, V K; Chigareva, E N; Belousova, O V

    2011-01-01

    The results of extraction of lambda-cigalotrin from dioxan aqueous solutions by hydrophobic organic solvents are presented. It is shown that the degree of extraction depends on the nature of the extractant, the water to dioxan ratio, and saturation of the water-dioxan layer with the electrolyte. The highest efficiency of lambda-cigalotrin extraction was achieved using chlorophorm as a solvent under desalination conditions. The extraction factor was calculated necessary to obtain the desired amount of lambda-cigalotrin from the water-dioxan solution (4:1) with the help of the extractants being used.

  5. The state of uranyl ions in water-dioxane solvent mixtures

    International Nuclear Information System (INIS)

    Geipel, G.; Nebel, D.; Baraniak, L.

    1985-01-01

    A comparison of the spectra of uranyl ions in HCl and dioxane solutions leads to the conclusion that dioxane promotes complex formation. The investigation of spectra showed that taking into account the hydrolysis of uranyl ions in dioxane containing solutions, two successive equilibrium reactions take place. The formation constants were determined. Conductivity measurements confirmed the spectrophotometrically determined equilibria. In solutions containing up to 60 % dioxane there is no incorporation of dioxane in the solvating envelope of the uranyl ion. (author)

  6. ER-1422: Biodegradation of 1,4-Dioxane

    Science.gov (United States)

    2007-08-01

    widely used as solvents, pesticides , gasoline additives, and a host of other applications. Most recently, the solvent stabilizer 1,4-dioxane has...the Stringfellow FBRs were sent to us to attempt to enrich native 1,4-dioxane degrading microorganisms . For the initial enrichment of bacterial...63:4216-4222. Steffan, R. J., Y. Farhan, C. W. Condee, and S. Drew. 2003. Bioremediation at a New Jersey Site Using Propane-Oxidizing Bacteria

  7. IRIS Toxicological Review of 1,4-Dioxane (with Inhalation ...

    Science.gov (United States)

    EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of 1,4-Dioxane (with inhalation update) that when finalized will appear on the Integrated Risk Information System (IRIS) database. 1,4-Dioxane is commonly used as a solvent, cleaning agent, chemical stabilizer, surface coating, adhesive agent, and an ingredient in chemical manufacture.

  8. Novel 1,3-dioxanes from apple juice and cider.

    Science.gov (United States)

    Kavvadias, D; Beuerle, T; Wein, M; Boss, B; König, T; Schwab, W

    1999-12-01

    Extracts obtained by XAD solid-phase extraction of apple juice and cider were separated by liquid chromatography on silica gel. Several new 1,3-dioxanes including the known 2-methyl-4-pentyl-1,3-dioxane and 2-methyl-4-[2'(Z)-pentenyl]-1,3-dioxane, were identified in the nonpolar fractions by GC/MS analysis and confirmed by chemical synthesis. The enantioselective synthesis of the stereoisomers of the 1,3-dioxanes was performed using (R)- and (R,S)-octane-1,3-diol and (R)- and (R,S)-5(Z)-octene-1,3-diol as starting material. Comparison with the isolated products indicated that the natural products consisted of a mixture of (2S,4R) and (2R,4R) stereoisomers in the ratio of approximately 10:1, except for 1,3-dioxanes generated from acetone and 2-butanone. It is assumed that the 1, 3-dioxanes are chemically formed in the apples and cider from the natural apple ingredients (R)-octane-1,3-diol, (R)-5(Z)-octene-1, 3-diol, (3R,7R)- and (3R,7S)-octane-1,3,7-triol, and the appropriate aldehydes and ketones, which are produced either by the apples or by yeast during fermentation of the apple juice.

  9. Effect of hydration on the amide I band in the binary solvents dioxane-D2O and dioxane-H2O

    International Nuclear Information System (INIS)

    Kobayashi, M.; Kobayashi, M.

    1980-01-01

    Hydration of amides in aqueous solutions has been studied by measuring the infrared spectra of amides (benzamide, p-methoxybenzamide, and ropionamide) in dioxane-D 2 O and dioxane-H 2 O mixtures. The absorption due to the C=O stretching (or amide I band) exhibited a very remarkable red shift accompanied by a characteristic change of the band shape as the water content in the medium increased. The spectral change is attributed to the change of the hydration state at the carbonyl oxygen. In the aqueous mixtures, amide molecules participate in an equilibrium among various states of hydration. The weighted mean frequency of the ν/sub C = O/ absorption, anti ν/sub C = O/, varied in proportion to the water contained in the medium. The difference between the anti ν/sub C = O/ value in pure water and that in pure dioxane,Δ anti ν, was used as a measure of the maximum degree of hydration. It was larger for propionamide than for the aromatic amides, suggesting that the steric effect of the substituents is of major importance in hydration. The isotope effect, Δ anti ν/sub D 2 O//Δ anti ν/sub H 2 O/, in the range from 1.4 to 1.6 for all cases examined, indicated that stronger hydration of amides occurred with D 2 O than with H 2 O

  10. Phytoremediation of 1,4-dioxane-containing recovered groundwater.

    Science.gov (United States)

    Ferro, Ari M; Kennedy, Jean; LaRue, James C

    2013-01-01

    The results of a pilot-scale phytoremediation study are reported in this paper. Small plots of trees established on a closed municipal waste landfill site were irrigated with recovered groundwater containing 1,4-dioxane (dioxane) and other volatile organic compounds (VOCs). The plots were managed to minimize the leaching of irrigation water, and leaching was quantified by the use of bromide tracer. Results indicated that the dioxane (2.5 microg/L) was effectively removed, probably via phytovolatilization, and that a full-scale phytoremediation system could be used. A system is now in place at the site in which the recovered groundwater can be treated using two different approaches. A physical treatment system (PTS) will be used during the winter months, and a 12 ha phytoremediation system (stands of coniferous trees) will be used during the growing season. The PTS removes VOCs using an air-stripper, and destroys dioxane using a photo-catalytic oxidation process. Treated water will be routed to the local sewer system. The phytoremediation system, located on the landfill, will be irrigated with effluent from the PTS air-stripper containing dioxane. Seasonal use of the phytoremediation system will reduce reliance on the photo-catalytic oxidation process that is extremely energy consumptive and expensive to operate.

  11. 5,5-Dihydroxybarbituric acid 1,4-dioxane hemisolvate

    Directory of Open Access Journals (Sweden)

    Thomas Gelbrich

    2010-05-01

    Full Text Available The asymmetric unit of the title compound,, C4H4N2O5·0.5C4H8O2, contains one molecule of 5,5-dihydroxybarbituric acid with a nearly planar barbiturate ring and half a molecule of 1,4-dioxane. The geometry of the centrosymmetric dioxane molecule is close to an ideal chair conformation. The crystal structure exhibits a complex three-dimensional hydrogen-bonded network. Barbiturate molecules are connected to one another via N—H...O=C, O—H...O=C and N—H...O(hydroxy interactions, while the barbituric acid molecule is linked to dioxane by an O—H...O contact.

  12. Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.

    Science.gov (United States)

    Black, R E; Hurley, F J; Havery, D C

    2001-01-01

    Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.

  13. Thermophysical study of 1,4-dioxane with cycloalkane mixtures

    International Nuclear Information System (INIS)

    Romero, C.; Giner, B.; Haro, M.; Artigas, H.; Lafuente, C.

    2006-01-01

    Densities, refractive indices, and surface tension for the binary mixtures 1,4-dioxane with cyclopentane or cylohexane have been determined at ambient pressure and at T = (283.15, 298.15, and 313.15) K. Excess volumes and refractive index and surface tension deviations have been calculated from the experimental data. Several relations between the thermophysical properties studied here have been tested using our experimental results

  14. Neutron Scattering of Residual Hydrogen in 1,4-Dioxane-D8 Liquid. Understanding Measurements with Molecular Dynamics Simulations

    Energy Technology Data Exchange (ETDEWEB)

    de Almeida, Valmor F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Hongjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Herwig, Kenneth W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kidder, Michelle [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-01-25

    That incoherent scattering from protiated molecular liquids adds a constant background to the measured scattering intensity is well known, but less appreciated is the fact that coherent scattering is also induced by the presence of hydrogen in a deuterated liquid. In fact, the scattering intensity can be very sensitive, in the small-q region, with respect to the amounts and distribution of residual H in the system. We used 1,4-dioxane liquid to demonstrate that the partial structure factors of the HD and DD atom pairs contribute significantly to inter-molecular scattering and that uncertainty in the extent of deuteration account for discrepancies between simulations and measurements. Both contributions to uncertainty have similar magnitudes: scattering interference of the hydrogen-deuterium pair, and complementary interference from the deuterium-deuterium pair by virtue of chemical inhomogeneity. This situation arises in practice since deuteration of liquids is often 99% or less. A combined experimental and extensive computational study of static thermal neutron scattering of 1,4-dioxane demonstrates the foregoing. We show, through simulations, that the reason for the differences is the content of protiated dioxane (vendors quote 1%). We estimate that up to 5% (at 298K and at 343K) protiated mole fraction may be involved in generating the scattering differences. Finally, we find that the particular distribution of hydrogen in the protiated molecules affects the results significantly; here we considered molecules to be either fully protiated or fully deuterated. This scenario best reconciles the computational and experimental results, and leads us to speculate that the deuteration synthesis process tends to leave a molecule either fully deuterated or fully protiated. Although we have used 1,4-dioxane as a model liquid, the effects described in this study extend to similar liquids and similar systematic experimental/computational studies can be performed to either

  15. Fluorinated tolane and dioxane liquid crystals for ferroelectric display applications

    International Nuclear Information System (INIS)

    Chu Chuan Dong

    1994-05-01

    The aim of this thesis was to make low viscosity, low birefringence, large negative dielectric anisotropy liquid-crystalline materials for use in ferroelectric liquid crystal mixtures to be used in high speed display devices. Saturated heterocyclic rings, dioxane and dioxaborinane, were chosen separately to be linked with a difluorophenyl system as the main component of the mesogenic core. In order to optimise the physical properties and to reduce the cost of the chiral materials, the strategy of making dopant-host mixtures was used. In addition to the difluorobiphenyl dioxaborinanes, three types of compounds were prepared possessing difluorophenyl rings and a dioxane ring: (i) difluorophenyl dioxanes and difluorobiphenyl dioxanes with the fluorinated ring in the middle of or at the end of the core; (ii) a number of compounds with linking groups, dimethylene (CH 2 CH 2 ), ester (COO), ethenylene (CH=CH) and ethynylene (C≡C) between adjacent benzene rings or between a dioxane ring and a benzene ring; (iii) difluorobiphenyl dioxanes possessing a chiral aliphatic chain were chosen as chiral dopants whose structure matched those of the host materials. Other compounds which have been synthesised are the difluorotolanes and difluorophenyl-ethynyl compounds, which were targeted because of the low viscosity of the tolane compounds and the negative dielectric anisotropy of the difluorophenyl ring. Fifty-six 2-(2,3-difluorobiphenyl-4'-yl)-1,3-dioxanes (n = 5-9, m = 5-10 or O5-O9; or n = 9, R' = OCH 2 CH(CH 3 )C 4 H 9 ) were prepared. Smectic C and nematic phases were observed for most of the alkyl-alkoxy homologues. Conversely, most of the dialkyl compounds exhibited smectic C, smectic A and nematic phases. The birefringences (Δn) and the dielectric anisotropies (Δε) of a number of materials have been determined. Three 2-(2,3-difluorobiphenyl-4-yl)-5-alkyl-1,3-dioxanes (n = 7, m = O7-O9) were prepared and only exhibit nematic phases. Two difluorophenyl dioxanes were

  16. Characterization of newly isolated Pseudonocardia sp. N23 with high 1,4-dioxane-degrading ability.

    Science.gov (United States)

    Yamamoto, Norifumi; Saito, Yuji; Inoue, Daisuke; Sei, Kazunari; Ike, Michihiko

    2018-01-02

    This study was conducted to elucidate the 1,4-dioxane degradation characteristics of a newly isolated 1,4-dioxane-degrading bacterial strain and evaluate the applicability of the strain to biological 1,4-dioxane removal from wastewater. A bacterial strain (designated strain N23) capable of degrading 1,4-dioxane as the sole carbon and energy source was isolated from an enrichment culture prepared from 1,4-dioxane-contaminated groundwater. Strain N23 was phylogenetically identified as belonging to the genus Pseudonocardia, based on 16S rRNA gene sequencing. 1,4-Dioxane degradation experiments revealed that strain N23 is capable of constitutive 1,4-dioxane degradation. Further, this strain exhibited the highest specific 1,4-dioxane degradation rate of 0.230 mg-1,4-dioxane (mg-protein) -1  h -1 among 1,4-dioxane-degrading bacteria with constitutively expressed degrading enzymes reported to date. In addition, strain N23 was shown to degrade up to 1100 mg L -1 of 1,4-dioxane without significant inhibition, and to maintain a high level of 1,4-dioxane degradation activity under a wide pH (pH 3.8-8.2) and temperature (20-35 °C) range. In particular, the specific 1,4-dioxane degradation rate, even at pH 3.8, was 83% of the highest rate at pH 7.0. In addition, strain N23 was capable of utilizing ethylene glycol and diethylene glycol, which are both considered to be present in 1,4-dioxane-containing industrial wastewater, as the sole carbon source. The present results indicate that strain N23 exhibits the potential for 1,4-dioxane removal from industrial wastewater. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  17. Fate of 1,4-dioxane in the aquatic environment: from sewage to drinking water.

    Science.gov (United States)

    Stepien, Daria K; Diehl, Peter; Helm, Johanna; Thoms, Alina; Püttmann, Wilhelm

    2014-01-01

    Potential health effects of 1,4-dioxane and the limited data on its occurrence in the water cycle command for more research. In the current study, mobility and persistence of 1,4-dioxane in the sewage-, surface-, and drinking water was investigated. The occurrence of 1,4-dioxane was determined in wastewater samples from four domestic sewage treatment plants (STP). The influent and effluent samples were collected during weekly campaigns. The average influent concentrations in all four plants ranged from 262 ± 32 ng L(-1) to 834 ± 480 ng L(-1), whereas the average effluent concentrations were between 267 ± 35 ng L(-1) and 62,260 ± 36,000 ng L(-1). No removal of 1,4-dioxane during water treatment was observed. Owing to its strong internal chemical bonding, 1,4-dioxane is considered non-biodegradable under conventional bio-treatment technologies. The source of increased 1,4-dioxane concentrations in the effluents was identified to originate from impurities in the methanol used in the postanoxic denitrification process in one of the STPs. In view of poor biodegradation in STPs, surface water samples were collected to establish an extent of 1,4-dioxane pollution. Spatial and temporal distribution of 1,4-dioxane in the Rivers Main, Rhine, and Oder was examined. Concentrations reaching 2200 ng L(-1) in the Oder River, and 860 ng L(-1) in both Main and Rhine River were detected. The average monthly load of 1,4-dioxane in the Rhine River was calculated to equal to 172 kg d(-1). In all rivers, concentration of 1,4-dioxane increased with distance from the spring and was found to negatively correlate with the discharge of the river. Additionally, bank filtration and drinking water samples from two drinking water facilities were analyzed for the presence of 1,4-dioxane. The raw water contained 650 ng L(-1)-670 ng L(-1) of 1,4-dioxane, whereas the concentration in the drinking water fell only to 600 ng L(-1) and 490 ng L(-1), respectively. Neither of the purification

  18. Implications of matrix diffusion on 1,4-dioxane persistence at contaminated groundwater sites.

    Science.gov (United States)

    Adamson, David T; de Blanc, Phillip C; Farhat, Shahla K; Newell, Charles J

    2016-08-15

    Management of groundwater sites impacted by 1,4-dioxane can be challenging due to its migration potential and perceived recalcitrance. This study examined the extent to which 1,4-dioxane's persistence was subject to diffusion of mass into and out of lower-permeability zones relative to co-released chlorinated solvents. Two different release scenarios were evaluated within a two-layer aquifer system using an analytical modeling approach. The first scenario simulated a 1,4-dioxane and 1,1,1-TCA source zone where spent solvent was released. The period when 1,4-dioxane was actively loading the low-permeability layer within the source zone was estimated to be high effective solubility. While this was approximately an order-of-magnitude shorter than the loading period for 1,1,1-TCA, the mass of 1,4-dioxane stored within the low-permeability zone at the end of the simulation period (26kg) was larger than that predicted for 1,1,1-TCA (17kg). Even 80years after release, the aqueous 1,4-dioxane concentration was still several orders-of-magnitude higher than potentially-applicable criteria. Within the downgradient plume, diffusion contributed to higher concentrations and enhanced penetration of 1,4-dioxane into the low-permeability zones relative to 1,1,1-TCA. In the second scenario, elevated 1,4-dioxane concentrations were predicted at a site impacted by migration of a weak source from an upgradient site. Plume cutoff was beneficial because it could be implemented in time to prevent further loading of the low-permeability zone at the downgradient site. Overall, this study documented that 1,4-dioxane within transmissive portions of the source zone is quickly depleted due to characteristics that favor both diffusion-based storage and groundwater transport, leaving little mass to treat using conventional means. Furthermore, the results highlight the differences between 1,4-dioxane and chlorinated solvent source zones, suggesting that back diffusion of 1,4-dioxane mass may be

  19. 1,4-Dioxane Remediation by Extreme Soil Vapor Extraction (XSVE). Screening-Level Feasibility Assessment and Design Tool in Support of 1,4-Dioxane Remediation by Extreme Soil Vapor Extraction (XSVE) ESTCP Project ER 201326

    Science.gov (United States)

    2017-10-01

    USER GUIDE 1,4-Dioxane Remediation by Extreme Soil Vapor Extraction (XSVE) Screening-Level Feasibility Assessment and Design Tool in...Support of 1,4-Dioxane Remediation by Extreme Soil Vapor Extraction (XSVE) ESTCP Project ER-201326 OCTOBER 2017 Rob Hinchee Integrated Science...Technology, Inc. 1509 Coastal Highway Panacea, FL 32346 8/8/2013 - 8/8/2018 10-2017 1,4-Dioxane Remediation by Extreme Soil Vapor Extraction (XSVE) Screening

  20. Decomposition of 1,4-dioxane by advanced oxidation and biochemical process.

    Science.gov (United States)

    Kim, Chang-Gyun; Seo, Hyung-Joon; Lee, Byung-Ryul

    2006-01-01

    This study was undertaken to determine the optimal decomposition conditions when 1,4-dioxane was degraded using either the AOPs (Advanced Oxidation Processes) or the BAC-TERRA microbial complex. The advanced oxidation was operated with H2O2, in the range 4.7 to 51 mM, under 254 nm (25 W lamp) illumination, while varying the reaction parameters, such as the air flow rate and reaction time. The greatest oxidation rate (96%) of 1,4-dioxane was achieved with H2O2 concentration of 17 mM after a 2-hr reaction. As a result of this reaction, organic acid intermediates were formed, such as acetic, propionic and butyric acids. Furthermore, the study revealed that suspended particles, i.e., bio-flocs, kaolin and pozzolan, in the reaction were able to have an impact on the extent of 1,4-dioxane decomposition. The decomposition of 1,4-dioxane in the presence of bio-flocs was significantly declined due to hindered UV penetration through the solution as a result of the consistent dispersion of bio-particles. In contrast, dosing with pozzolan decomposed up to 98.8% of the 1,4-dioxane after 2 hr of reaction. Two actual wastewaters, from polyester manufacturing, containing 1,4-dioxane in the range 370 to 450 mg/L were able to be oxidized by as high as 100% within 15 min with the introduction of 100:200 (mg/L) Fe(II):H202 under UV illumination. Aerobic biological decomposition, employing BAC-TERRA, was able to remove up to 90% of 1,4-dioxane after 15 days of incubation. In the meantime, the by-products (i.e., acetic, propionic and valeric acid) generated were similar to those formed during the AOPs investigation. According to kinetic studies, both photo-decomposition and biodegradation of 1,4-dioxane followed pseudo first-order reaction kinetics, with k = 5 x 10(-4) s(-1) and 2.38 x 10(-6) s(-1), respectively. It was concluded that 1,4-dioxane could be readily degraded by both AOPs and BAC-TERRA, and that the actual polyester wastewater containing 1,4-dioxane could be successfully

  1. Interaction enthalpies of solid human serum albumin with water-dioxane mixtures: comparison with water and organic solvent vapor sorption

    International Nuclear Information System (INIS)

    Sirotkin, Vladimir A.; Faizullin, Djihanguir A.

    2004-01-01

    Enthalpy changes (ΔH tot ) on the immersion of dehydrated human serum albumin (HSA) into water-dioxane mixtures have been measured using a Setaram BT-2.15 calorimeter at 298 K. Thermodynamic activity of water was varied from 0 to 1. Calorimetric results are discussed together with the FTIR-spectroscopic data on water and organic solvent vapor adsorption/desorption isotherms on solid HSA. Dioxane sorption exhibits a pronounced hysteresis. Calorimetric and dioxane desorption dependencies consist of two parts. No dioxane sorption was observed in low water activity region (a w tot values are close to zero. At water activity about 0.5 the sharp exothermic drop of the interaction enthalpy values was observed. This exothermic drop is accompanied by the sharp increase in the amount of sorbed dioxane and additional water sorption (compared with that for pure water). Dioxane adsorption branch resembles a smooth curve. In this case, solid HSA binds more than 300 mol dioxane/mol HSA at low water activities. By using a water activity-based comparison we distinguished between dioxane-assisted and dioxane-competitive effect on water sorption. The obtained results demonstrate that the hydration 'history' of solid protein is an important factor that controls as the state of protein macromolecule as well as the sorption of low-molecular organic molecules

  2. Low level estimation of 1,4-dioxane in ambient air

    International Nuclear Information System (INIS)

    Pandit, G.G.; Sahu, S.K.; Puranik, V.D.

    2007-05-01

    The chemical, 1,4-dioxane does have much relevance with respect to Indian Nuclear Power Programme for counting of Tritium, which is mainly generated during the operation of nuclear research reactors and power reactors which use heavy water. Tritium analysis is routinely carried out at BARC. The scintillation solutions which are used for tritium counting, consist of mainly 1,4 dioxane and naphthalene along with minor concentration of PPO/POPOP. Each sample analysis generates about 10 ml of tritium contaminated spent scintillation liquid waste. Total generation rate of the waste in a typical PHWR reactor is about 2-3 m 3 /year. Controlled incineration of scintillation liquids has been opted at BARC for the treatment of radioactive organic waste. Now that 1,4-dioxane has shown threat to human health and environment, it is important and necessary to know its levels (concentrations) in different environmental compartments to evaluate the risks associated with it. Standard methods are available for the measurement of 1,4-dioxane in air. Higher concentration can be estimated by direct analysis but estimation at lower levels (parts per billion-ppb) requires pre concentration prior to its analysis. Here an improved method that offers increased sensitivity has been used for determining lower levels of 1,4-dioxane. This report presents (1) the development of the methodology for the estimation of 1,4-dioxane at ppb levels using cryogenic pre-concentration and subsequent analysis by Gas Chromatograph with Electron Capture detector (GC-ECD) (2) techniques to check the incineration efficiency and release of 1,4-dioxane to the environment. The data generated by this study could be further used in the evaluation of risk. (author)

  3. Identification of the intermediates of in vivo oxidation of 1 ,4-dioxane by monooxygenase-containing bacteria.

    Science.gov (United States)

    Mahendra, Shaily; Petzold, Christopher J; Baidoo, Edward E; Keasling, Jay D; Alvarez-Cohen, Lisa

    2007-11-01

    1,4-dioxane is a probable human carcinogen and an emerging water contaminant. Monooxygenase-expressing bacteria have been shown to degrade dioxane via growth-supporting as well as cometabolic mechanisms. In this study, the intermediates of dioxane degradation by monooxygenase-expressing bacteria were determined by triple quadrupole-mass spectrometry and Fourier transform ion cyclotron resonance-mass spectrometry. The major intermediates were identified as 2-hydroxyethoxyacetic acid (HEAA), ethylene glycol, glycolate, and oxalate. Studies with uniformly labeled 14C dioxane showed that over 50% of the dioxane was mineralized to CO2 by CB1190, while 5% became biomass-associated after 48 h. Volatile organic acids and non-volatiles, respectively, accounted for 20 and 11% of the radiolabeled carbon. Although strains cometabolizing dioxane exhibited limited transformation capacities, nearly half of the initial dioxane was recovered as CO2. On the basis of these analytical results, we propose a pathway for dioxane oxidation by monooxygenase-expressing cells in which dioxane is first converted to 2-hydroxy-1,4-dioxane, which is spontaneously oxidized to HEAA. During a second monooxygenation step, HEAA is further hydroxylated, resulting in a mixture of dihydroxyethoxyacetic acids with a hydroxyl group at the ortho or para position. After cleavage of the second ether bond, small organic molecules such as ethylene glycol, glycolate, glyoxalate, and oxalate are progressively formed, which are then mineralized to CO2 via common cellular metabolic pathways. Bioremediation of dioxane via this pathway is not expected to cause an accumulation of toxic compounds in the environment.

  4. Quantitative determination of 1,4-dioxane and tetrahydrofuran in groundwater by solid phase extraction GC/MS/MS.

    Science.gov (United States)

    Isaacson, Carl; Mohr, Thomas K G; Field, Jennifer A

    2006-12-01

    Groundwater contamination by cyclic ethers, 1,4-dioxane (dioxane), a probable human carcinogen, and tetrahydrofuran (THF), a co-contaminant at many chlorinated solvent release sites, are a growing concern. Cyclic ethers are readily transported in groundwater, yet little is known about their fate in environmental systems. High water solubility coupled with low Henry's law constants and octanol-water partition coefficients make their removal from groundwater problematic for both remedial and analytical purposes. A solid-phase extraction (SPE) method based on activated carbon disks was developed for the quantitative determination of dioxane and THF. The method requires 80 mL samples and a total of 1.2 mL of solvent (acetone). The number of steps is minimized due to the "in-vial" elution of the disks. Average recoveries for dioxane and THF were 98% and 95%, respectively, with precision, as indicated by the relative standard deviation of <2% to 6%. The method quantitation limits are 0.31 microg/L for dioxane and 3.1 microg/L for THF. The method was demonstrated by analyzing groundwater samples for dioxane and THF collected during a single sampling campaign at a TCA-impacted site. Dioxane concentrations and areal extent of dioxane in groundwater were greater than those of either TCA or THF.

  5. 1,4-Dioxane drinking water occurrence data from the third unregulated contaminant monitoring rule.

    Science.gov (United States)

    Adamson, David T; Piña, Elizabeth A; Cartwright, Abigail E; Rauch, Sharon R; Hunter Anderson, R; Mohr, Thomas; Connor, John A

    2017-10-15

    This study examined data collected from U.S. public drinking water supplies in support of the recently-completed third round of the Unregulated Contaminant Monitoring Rule (UCMR3) to better understand the nature and occurrence of 1,4-dioxane and the basis for establishing drinking water standards. The purpose was to evaluate whether the occurrence data for this emerging but federally-unregulated contaminant fit with common conceptual models, including its persistence and the importance of groundwater contamination for potential exposure. 1,4-Dioxane was detected in samples from 21% of 4864 PWSs, and was in exceedance of the health-based reference concentration (0.35μg/L) at 6.9% of these systems. In both measures, it ranked second among the 28 UCMR3 contaminants. Although much of the focus on 1,4-dioxane has been its role as a groundwater contaminant, the detection frequency for 1,4-dioxane in surface water was only marginally lower than in groundwater (by a factor of 1.25; pwater (pwater sources tend to be more dilute. Sampling from large systems increased the likelihood that 1,4-dioxane was detected by a factor of 2.18 times relative to small systems (pwater were highly associated with detections of other chlorinated compounds particularly 1,1-dichlorethane (odds ratio=47; pchlorinated solvent stabilizer. Based on aggregated nationwide data, 1,4-dioxane showed evidence of a decreasing trend in concentration and detection frequency over time. These data suggest that the loading to drinking water supplies may be decreasing. However, in the interim, some water supply systems may need to consider improving their treatment capabilities in response to further regulatory review of this compound. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Activated Persulfate Treatment of 1,4-Dioxane in the Presence of Chlorinated Solvent Co-contaminants

    Science.gov (United States)

    Boving, T. T.; Eberle, D. E. H.; Ball, R.

    2014-12-01

    1,4-dioxane is an emerging groundwater contaminant and a likely human carcinogen. Due to its history as a stabilizer in chlorinated solvents, 1,4-dioxane is often found as a co-contaminant at solvent releases sites such as landfills, solvent recycling facilities, vapor decreasing operations, and fire-training areas. Historically, 1,4-dioxane was not routinely analyzed for at solvent release sites. The lack of analyses and the limitations of the analyses that were performed (i.e. high reporting limits) means that the scale of 1,4-dioxane subsurface contamination is still emerging. With the number of known 1,4-dioxane sites increasing, the need for cost effective 1,4-dioxane remediation technologies is rising as well. Remediation strategies that are capable of treating both 1,4-dioxane as well as chlorinated co-contaminants are of particular importance, especially when treating mixed-waste source zones. In the present study, we examined the fate of 1,4-dioxane during the targeted remediation of aqueous phase volatile organic compounds (VOC) using an activated persulfate based ISCO method (OxyZone®). Bench scale laboratory experiments are used to evaluate the treatability of 1,4-dioxane both as a single compound and in the presence of trichloroethene (TCE) and 1,1,1-trichloroethane (1,1,1-TCA). Possible dependencies on oxidant concentration and reaction kinetics were studied. Preliminary results are promising and show that OxyZone® is persistent and long lived, with oxidation of 1,4-dioxane continuing more than 12 days after initial dosage, even at dilute oxidant concentrations. The oxidative destruction of 1,4-dioxane, TCE and 1,1,1-TCA in single compound batch systems followed pseudo first order reaction kinetics. The rate of oxidation for each contaminant increased linearly with increasing persulfate concentration over the range of oxidant concentrations tested. The rate of oxidative destruction, from most easily degraded to least was: TCE > 1,4-Dioxane > 1

  7. Abiotic and bioaugmented granular activated carbon for the treatment of 1,4-dioxane-contaminated water.

    Science.gov (United States)

    Myers, Michelle A; Johnson, Nicholas W; Marin, Erick Zerecero; Pornwongthong, Peerapong; Liu, Yun; Gedalanga, Phillip B; Mahendra, Shaily

    2018-06-04

    1,4-Dioxane is a probable human carcinogen and an emerging contaminant that has been detected in surface water and groundwater resources. Many conventional water treatment technologies are not effective for the removal of 1,4-dioxane due to its high water solubility and chemical stability. Biological degradation is a potentially low-cost, energy-efficient approach to treat 1,4-dioxane-contaminated waters. Two bacterial strains, Pseudonocardia dioxanivorans CB1190 (CB1190) and Mycobacterium austroafricanum JOB5 (JOB5), have been previously demonstrated to break down 1,4-dioxane through metabolic and co-metabolic pathways, respectively. However, both CB1190 and JOB5 have been primarily studied in laboratory planktonic cultures, while most environmental microbes grow in biofilms on surfaces. Another treatment technology, adsorption, has not historically been considered an effective means of removing 1,4-dioxane due to the contaminant's low K oc and K ow values. We report that the granular activated carbon (GAC), Norit 1240, is an adsorbent with high affinity for 1,4-dioxane as well as physical dimensions conducive to attached bacterial growth. In abiotic batch reactor studies, 1,4-dioxane adsorption was reversible to a large extent. By bioaugmenting GAC with 1,4-dioxane-degrading microbes, the adsorption reversibility was minimized while achieving greater 1,4-dioxane removal when compared with abiotic GAC (95-98% reduction of initial 1,4-dioxane as compared to an 85-89% reduction of initial 1,4-dioxane, respectively). Bacterial attachment and viability was visualized using fluorescence microscopy and confirmed by amplification of taxonomic genes by quantitative polymerase chain reaction (qPCR) and an ATP assay. Filtered samples of industrial wastewater and contaminated groundwater were also tested in the bioaugmented GAC reactors. Both CB1190 and JOB5 demonstrated 1,4-dioxane removal greater than that of the abiotic adsorbent controls. This study suggests that

  8. IN SITU OXIDATION FIELD PILOT OF 1,4-DIOXANE AT THE COOPER DRUM SUPERFUND SITE

    Science.gov (United States)

    1,4-Dioxane, a solvent in paints, varnishes, lacquers, cosmetics, deodorants, cleaning and detergent preparations fluids, has attracted a lot of notice recently because its chemical analytical detection limit has recently been lowered from 50 µg/L to 1 µg/L. It is now commonly de...

  9. Short-chain grafting of tetrahydrofuran and 1,4-dioxane cycles on vinylchloride-maleic anhydride copolymer

    Directory of Open Access Journals (Sweden)

    2009-01-01

    Full Text Available Mass increase of vinylchloride-maleic anhydride (VC-MA copolymer samples aged in tetrahydrofuran (THF or in 1,4-dioxane results from chemical interaction of VC-MA macromolecules with 1,4-dioxane or THF. Microstructure of the products of such modification was proved by infrared spectroscopy (IR- and nuclear magnetic resonance spectroscopy (13C NMR and 1H NMR. Mechanism of modification has been proposed. The results of microstructure research of VC-MA samples aged in THF and in 1,4-dioxane coincide with already known data on the reactions of opening of these and other oxygen-containing cycles under mild conditions.

  10. Synthesis of 1, 4-Dioxan-2-one from 1, 3-Dioxolane and Carbon Monoxide over Cation-exchange Resin Catalyst

    OpenAIRE

    Takagi, Hiroyuki; Oumi, Yasunori; Uozumi, Toshiya; Masuda, Takashi; Sano, Tsuneji

    2001-01-01

    The possibility of the synthesis of 1, 4-dioxan-2-one (p-dioxanon) by carbonylation of 1, 3-dioxolane (cyclic ether) over Nafion® NR-50 cation-exchange resin catalyst was investigated. 1, 4-Dioxan-2-one, one of the cyclic esterethers used as a monomer of polyester, was obtained by depolymerization of polyester oligomers. The maximum yield (40%) of 1, 4-dioxan-2-one was achieved under reaction conditions of 25MPa initial PCO, 120°C reaction temperature and 4h reaction time.

  11. Genome Sequence of the 1,4-Dioxane-Degrading Pseudonocardia dioxanivoransStrain CB1190▿

    Science.gov (United States)

    Sales, Christopher M.; Mahendra, Shaily; Grostern, Ariel; Parales, Rebecca E.; Goodwin, Lynne A.; Woyke, Tanja; Nolan, Matt; Lapidus, Alla; Chertkov, Olga; Ovchinnikova, Galina; Sczyrba, Alexander; Alvarez-Cohen, Lisa

    2011-01-01

    Pseudonocardia dioxanivoransCB1190 is the first bacterium reported to be capable of growth on the environmental contaminant 1,4-dioxane and the first member of the genus Pseudonocardiafor which there is an annotated genome sequence. Preliminary analysis of the genome (chromosome and three plasmids) indicates that strain CB1190 possesses several multicomponent monooxygenases that could be involved in the aerobic degradation of 1,4-dioxane and other environmental contaminants. PMID:21725009

  12. In Situ Bioremediation of 1,4-Dioxane by Methane Oxidizing Bacteria in Coupled Anaerobic-Aerobic Zones

    Science.gov (United States)

    2016-02-11

    FINAL REPORT In Situ Bioremediation of 1,4-Dioxane by Methane Oxidizing Bacteria in Coupled Anaerobic-Aerobic Zones SERDP Project ER-2306...volatile organic compound (CVOCs), ethene and ethane in groundwater at Raritan Arsenal Area 18C after in situ bioremediation . 4 List of...aquifers, the bioremediation approach most commonly used for chlorinated solvents. The ability of methanotrophs to biodegrade 1,4-dioxane was

  13. Characterizing the intrinsic bioremediation potential of 1,4-dioxane and trichloroethene using innovative environmental diagnostic tools.

    Science.gov (United States)

    Chiang, Sheau-Yun Dora; Mora, Rebecca; Diguiseppi, William H; Davis, Greg; Sublette, Kerry; Gedalanga, Phillip; Mahendra, Shaily

    2012-09-01

    An intrinsic biodegradation study involving the design and implementation of innovative environmental diagnostic tools was conducted to evaluate whether monitored natural attenuation (MNA) could be considered as part of the remedial strategy to treat an aerobic aquifer contaminated with 1,4-dioxane and trichloroethene (TCE). In this study, advanced molecular biological and stable isotopic tools were applied to confirm in situ intrinsic biodegradation of 1,4-dioxane and TCE. Analyses of Bio-Trap® samplers and groundwater samples collected from monitoring wells verified the abundance of bacteria and enzymes capable of aerobically degrading TCE and 1,4-dioxane. Furthermore, phospholipid fatty acid analysis with stable isotope probes (PLFA-SIP) of the microbial community validated the ability for microbial degradation of TCE and 1,4-dioxane. Compound specific isotope analysis (CSIA) of groundwater samples for TCE resulted in δ(13)C values that indicated likely biodegradation of TCE in three of the four monitoring wells sampled. Results of the MNA evaluation showed that enzymes capable of aerobically degrading TCE and 1,4-dioxane were present, abundant, and active in the aquifer. Taken together, these results provide direct evidence of the occurrence of TCE and 1,4-dioxane biodegradation at the study site, supporting the selection of MNA as part of the final remedy at some point in the future.

  14. Quantitative determination of residual 1,4-dioxane in three-dimensional printed bone scaffold

    Directory of Open Access Journals (Sweden)

    Ling Li

    2018-04-01

    Full Text Available Summary: Background/Objective: A novel porous scaffold poly (lactide-co-glycolide and tricalcium phosphate (PLGA/TCP was developed by three-dimensional printing technology for bone defect repair. As a Class 2 solvent with less severe toxicity, content of residual 1,4-dioxane in this newly developed scaffold should be rigorously controlled when it is translated to clinical use. In this study, a headspace gas chromatography-mass spectrometric (HS-GC-MS method and related testing protocol were developed for quantitative determination of 1,4-dioxane in the PLGA/TCP composite scaffolds. Methods: Matrix effect analysis was used to optimise the pretreatment method of the scaffolds. Then, the procedure for testing 1,4-dioxane using HS-GC-MS was set up. The accuracy, precision, and robustness of this newly developed quantitative method were also validated before quantification of 1,4-dioxane in the scaffolds with different drying procedures. Results: Dimethyl formamide (DMF was the optimal solvent for dissolving scaffolds for GC-MS with proper sensitivity and without matrix effect. Then, the optimised procedure was determined as: the scaffolds were dissolved in DMF and kept at 90°C for 40 minutes, separated on a HP-5MS column, and detected by mass spectroscopy. Recovery experiments gave 97.9–100.7% recovery for 1,4-dioxane. The linear range for 1,4-dioxane was determined as 1–40 ppm with linear correlation coefficient ≥ 0.9999. Intraday and interday precision was determined as being within relative standard deviation of below 0.68%. The passable drying procedure was related to lyophilising (−50°C, 50 Pa the scaffolds for 2 days and drying in vacuum (50 Pa for 7 days. Conclusion: This is the first quantitative method established to test 1,4-dixoane in a novel scaffold. This method was validated with good accuracy and reproducibility, and met the methodological requirements of the Guideline 9101 documented in the Chinese Pharmacopoeia 2015

  15. Oxygenase-Catalyzed Biodegradation of Emerging Water Contaminants: 1,4-Dioxane and N-Nitrosodimethylamine

    Science.gov (United States)

    2012-02-01

    and treat operations (54, 144). Aitchison et al. (1) have reported phytoremediation of dioxane by hybrid poplar trees. In their laboratory studies...world, the microsomal fractions of tulip bulbs (145), spinach, and lettuce (29) had all been shown to metabolize NDMA. In addition, many higher...cDNA was synthesized, fragmented, labeled, and hybridized to arrays according to the protocols outlined in section 3 of the Affymetrix GeneChip

  16. N-(4-Fluorophenyl-2,6-dimethyl-1,3-dioxan-4-amine

    Directory of Open Access Journals (Sweden)

    Gottimukkala Rambabu

    2013-11-01

    Full Text Available In the title compound, C12H16FNO2, the dioxane ring adopts a chair conformation with the methyl substituents and the C—N bond in equatorial orientations. Its mean plane subtends a dihedral angle of 40.17 (6° with the benzene ring. In the crystal, weak N—H...F hydrogen bonds link the molecules into C(7 chains propagating in [100].

  17. Proof-of-Concept Study: Novel Microbially-Driven Fenton Reaction for In Situ Remediation of Groundwater Contaminated with 1,4-Dioxane, Tetrachloroethene (PCE) and Trichloroethene (TCE)

    Science.gov (United States)

    2014-09-17

    with 1,4-Dioxane, Tetrachloroethene (PCE) and Trichloroethene ( TCE ) SERDP Project ER-2305 September 2014 Thomas DiChristina Georgia...HO) radicals that degrade 1,4- dioxane, TCE , and PCE. In comparison to conventional (purely abiotic) Fenton reactions, the microbially-driven Fenton...reaction operates at circumneutral pH and does not require addition of exogenous H2O2 or UV irradiation to regenerate Fe(II). The 1,4-dioxane, TCE

  18. Proton magnetic resonance studies in solutions of o- and p-hydroxy benzoic acids in dioxan

    International Nuclear Information System (INIS)

    Arulmozhi, V.; Srinivasa Rao, A.; Balasubramanian, V.

    1990-01-01

    High resolution proton(NMR) studies were carried out in solutions of o- and p-hydroxy benzoic acids(OHBA and PHBA) in dioxan (D) for several solute concentrations in the range of 0.01 to 0.10 mole fraction (mf). The spectra corresponding to OH and COOH protons could be distinguished in solutions of OHBA in D whereas solution of PHBA in D show only peak in the range of chemical shifts attributable to OH and COOH protons. In the solution of OHBA in dioxan the chemical shift of the proton of the hydroxyl group increases with increase of solute concentration and attains a maximum at a solute concentration of 0.04 mf and then decreases with further increase of solute concentration. For the carboxyl group, the chemical shift increase with increase of solute concentration and attians a maximum at 0.08 mf solute concentration. In solutions of PHBA in D the chemical shift of the single line observed increases with increase of solute concentration and attains a maximum at a solute concentration of 0.05 mf. The data are interpreted as due to formation of hydrogen bonds between the molecule of OHBA and PHBA and dioxan. The proton magnetic relaxation studies in the above solutions also confirm the above findings. (author). 6 refs., 5 figs

  19. Structural and dipolar properties of the voltage-dependent pore former alamethicin in octanol/dioxane.

    Science.gov (United States)

    Schwarz, G; Savko, P

    1982-01-01

    Dielectric constant and loss of the membrane-active peptide alamethicin in octanol/dioxane mixtures have been measured at frequencies between 5 kHz and 50 MHz. On the basis of a rotational mechanism of dipolar orientation, the observed dispersion provides information regarding size, shape, and dipole moment of the structural entities which the solute may assume in media of diverse lipophilicity. Particularly detailed results are obtained in a pure octanol solvent where an apparent molecular weight of alamethicin could be determined. It turns out that in this quite lipophilic medium most of the peptide material exists as a monomer particle that has approximate length and diameter of 35 and 13 A, respectively. It carries a dipole moment of approximately 75 Debye units (directed nearly parallel to the long axis). At our concentrations of a few milligrams per milliliters, appreciable formation of dimers by head-to-tail linkage is indicated. When the octanol content is reduced by adding greater amounts of dioxane, larger particles are encountered. This is accompanied by a decrease of the effective polarity. The inherent increase of hydrophilicity in the dioxane-enriched solvent apparently favors another monomer conformation that has a low dipole moment and easily aggregates to some kind of micelle. PMID:7115881

  20. Hydrate phase equilibria of furan, acetone, 1,4-dioxane, TBAC and TBAF

    International Nuclear Information System (INIS)

    Kamran-Pirzaman, Arash; Pahlavanzadeh, Hassan; Mohammadi, Amir H.

    2013-01-01

    Highlights: • Experimental hydrate dissociation conditions are reported for CO 2 /methane + some water soluble/insoluble hydrate formers. • An isochoric pressure-search method was used to generate the experimental data. • The data are compared with the corresponding literature data in the presence of pure water. • The hydrate promotion effects of acetone, 1,4-dioxane, furan, TBAC and TBAF are discussed. -- Abstract: In this communication, we first report experimental hydrate dissociation pressures for the methane/carbon dioxide + furan/acetone/1,4-dioxane + water and the methane + tetra n-butyl ammonium chloride (TBAC) + water as well as the carbon dioxide + tetra n-butyl ammonium floride (TBAF) + water systems in the temperature ranges of (269.9 to 303.3) K. An isochoric pressure-search method was used to generate the experimental data. The hydrate dissociation data are compared with the corresponding literature data, if exists, and the literature data in the presence of pure water and acceptable agreement is observed. A discussion is made on hydrate promotion effects of acetone, 1,4-dioxane, furan, TBAC and TBAF

  1. Pilot test of biological removal of 1,4-dioxane from a chemical factory wastewater by gel carrier entrapping Afipia sp. strain D1

    Energy Technology Data Exchange (ETDEWEB)

    Isaka, Kazuichi, E-mail: kazuichi.isaka.mp@hitachi.com [Matsudo Research Center, Infrastructure System Company, Hitachi, Ltd., 537 Kami-hongo, Matsudo, Chiba 271-0064 (Japan); Udagawa, Makiko [Matsudo Research Center, Infrastructure System Company, Hitachi, Ltd., 537 Kami-hongo, Matsudo, Chiba 271-0064 (Japan); Sei, Kazunari, E-mail: ksei@kitasato-u.ac.jp [Division of Sustainable Energy and Environmental Engineering, Osaka University, Yamadaoka, 2-1, Suita, Osaka 565-0871 (Japan); Department of Health Science, School of Allied Health Sciences, Kitasato University, 1-15-1 Kitasato, Sagamihara-Minami, Kanagawa 252-0373 (Japan); Ike, Michihiko, E-mail: ike@see.eng.osaka-u.ac.jp [Division of Sustainable Energy and Environmental Engineering, Osaka University, Yamadaoka, 2-1, Suita, Osaka 565-0871 (Japan)

    2016-03-05

    Highlights: • Two pilot-scale biological 1,4-dioxane (1,4-D) treatment systems were operated. • Gel cubes entrapping Afipia sp. strain D1 were used for real wastewater treatment. • The maximum 1,4-dioxane removal rates of 0.72 kg m{sup −3} day{sup −1} was observed. • Monod model describes 1,4-D degradation, showing half saturation constant is 28 mg L{sup −1}. - Abstract: A pilot-scale (120 L) bioreactor system using a gel carrier-entrapped pure bacterial strain, Afipia sp. strain D1, capable of degrading 1,4-dioxane as a sole carbon and energy source was constructed and applied to treat real industrial wastewater containing 1,4-dioxane from a chemical factory. Although the wastewater not only contained high concentrations of 1,4-dioxane but also considerable amounts of other organic compounds (73 mg-TOC L{sup −1} on average), the bioreactor could efficiently remove 1,4-dioxane without significant inhibitory effects. The reactor startup could be completed within approximately 1 month by increasing the 1,4-dioxane loading rate (0.09–0.47 kg-dioxane m{sup −3} d{sup −1}) in a stepwise manner. Effective 1,4-dioxane removal was stably maintained for 3 months with an influent 1,4-dioxane of 570–730 mg L{sup −1}, giving an average effluent concentration and removal rate of 3.4 mg L{sup −1} and 0.46 kg-dioxane m{sup −3} d{sup −1}, respectively. A 1,4-dioxane loading fluctuation between 0.14 and 0.72 kg-dioxane m{sup −3} d{sup −1} did not significantly affect its removal, and more than 99% removal efficiency was constantly maintained. The Monod model could well describe the relationship between the effluent 1,4-dioxane concentration and 1,4-dioxane removal rates of the bioreactors, showing that the half-saturation constant (Ks) was 28 mg L{sup −1}.

  2. Pilot test of biological removal of 1,4-dioxane from a chemical factory wastewater by gel carrier entrapping Afipia sp. strain D1

    International Nuclear Information System (INIS)

    Isaka, Kazuichi; Udagawa, Makiko; Sei, Kazunari; Ike, Michihiko

    2016-01-01

    Highlights: • Two pilot-scale biological 1,4-dioxane (1,4-D) treatment systems were operated. • Gel cubes entrapping Afipia sp. strain D1 were used for real wastewater treatment. • The maximum 1,4-dioxane removal rates of 0.72 kg m"−"3 day"−"1 was observed. • Monod model describes 1,4-D degradation, showing half saturation constant is 28 mg L"−"1. - Abstract: A pilot-scale (120 L) bioreactor system using a gel carrier-entrapped pure bacterial strain, Afipia sp. strain D1, capable of degrading 1,4-dioxane as a sole carbon and energy source was constructed and applied to treat real industrial wastewater containing 1,4-dioxane from a chemical factory. Although the wastewater not only contained high concentrations of 1,4-dioxane but also considerable amounts of other organic compounds (73 mg-TOC L"−"1 on average), the bioreactor could efficiently remove 1,4-dioxane without significant inhibitory effects. The reactor startup could be completed within approximately 1 month by increasing the 1,4-dioxane loading rate (0.09–0.47 kg-dioxane m"−"3 d"−"1) in a stepwise manner. Effective 1,4-dioxane removal was stably maintained for 3 months with an influent 1,4-dioxane of 570–730 mg L"−"1, giving an average effluent concentration and removal rate of 3.4 mg L"−"1 and 0.46 kg-dioxane m"−"3 d"−"1, respectively. A 1,4-dioxane loading fluctuation between 0.14 and 0.72 kg-dioxane m"−"3 d"−"1 did not significantly affect its removal, and more than 99% removal efficiency was constantly maintained. The Monod model could well describe the relationship between the effluent 1,4-dioxane concentration and 1,4-dioxane removal rates of the bioreactors, showing that the half-saturation constant (Ks) was 28 mg L"−"1.

  3. Halogen Oxygen Interactions and Disorder Modes in Pressure Frozen Complexes of 1,2-Dihaloperfluoroethanes with 1,4-Dioxane (Preprint)

    National Research Council Canada - National Science Library

    Olejniczak, Anna; Katrusiak, Andrzej

    2007-01-01

    ...: 1,4-dioxane at 0.62(5) GPa/296 K were determined by single-crystal X-ray diffraction. Also the single-crystal of 1,4-dioxane separated from 1,2-dibromoperfluoroethane, which remained liquid, was investigated at 0.42 GPa/296 K...

  4. The effect of pH on UV-based advanced oxidation technologies - 1,4-Dioxane degradation

    Energy Technology Data Exchange (ETDEWEB)

    Vescovi, Tania [ARC Centre of Excellence for Functional Nanomaterials, School of Chemical Sciences and Engineering, University of New South Wales, NSW 2052 (Australia); Coleman, Heather M., E-mail: h.coleman@unsw.edu.au [UNSW Water Research Centre, School of Civil and Environmental Engineering, University of New South Wales, NSW 2052 (Australia); Amal, Rose [ARC Centre of Excellence for Functional Nanomaterials, School of Chemical Sciences and Engineering, University of New South Wales, NSW 2052 (Australia)

    2010-10-15

    1,4-Dioxane, is a synthetic organic compound used widely throughout industry as a solvent. 1,4-Dioxane causes liver damage and kidney failure and has been shown to be carcinogenic to animals, and is a potential carcinogen to humans. Its recalcitrant nature means that conventional water treatment methods are ineffective in removing it from water. A class of technologies called advanced oxidation technologies has been shown to completely mineralise 1,4-dioxane. In this study the effects of pH on TiO{sub 2} photocatalysis reactor systems were investigated. pH was found to significantly affect the efficiencies of these processes with neutral pH conditions the most effective.

  5. Indomethacin solubility estimation in 1,4-dioxane + water mixtures by the extended hildebrand solubility approach

    Directory of Open Access Journals (Sweden)

    Miller A Ruidiaz

    2011-09-01

    Full Text Available Extended Hildebrand Solubility Approach (EHSA was successfully applied to evaluate the solubility of Indomethacin in 1,4-dioxane + water mixtures at 298.15 K. An acceptable correlation-performance of EHSA was found by using a regular polynomial model in order four of the W interaction parameter vs. solubility parameter of the mixtures (overall deviation was 8.9%. Although the mean deviation obtained was similar to that obtained directly by means of an empiric regression of the experimental solubility vs. mixtures solubility parameters, the advantages of EHSA are evident because it requires physicochemical properties easily available for drugs.

  6. IMPLEMENTATION OF DIOXANE AND DIESEL FUEL BLENDS TO REDUCE EMISSION AND TO IMPROVE PERFORMANCE OF THE COMPRESSION IGNITION ENGINE

    OpenAIRE

    SENDILVELAN S.; SUNDAR RAJ C.

    2017-01-01

    Performance of a compression ignition engine fuelled with 1, 4 Dioxane- diesel blends is evaluated. A single-cylinder, air-cooled, direct injection diesel engine developing a power output of 5.2 kW at 1500 rev/min is used. Base data is generated with standard diesel fuel subsequently; five fuel blends namely 90:10, 80:20, 70:30, 60:40 and 50:50 percentages by volume of diesel and dioxane were prepared and tested in the diesel engine. Engine performance and emission data were used to optimize ...

  7. PERFORMANCE ANALYSIS OF 1,4 DIOXANE-ETHANOL-DIESEL BLENDS ON DIESEL ENGINES WITH AND WITHOUT THERMAL BARRIER COATING

    OpenAIRE

    Chockalingam Sundar Raj; Sambandam Arul; Subramanian Sendilvelan; Ganapathy Saravanan

    2010-01-01

    1,4 dioxane, a new additive allows the splash blending of ethanol in diesel in a clear solution. The objective of this investigation is to first create a stable ethanol-diesel blended fuel with 10% 1,4 dioxane additive, and then to generate performance, combustion and emissions data for evaluation of different ethanol content on a single cylinder diesel engine with and without thermal barrier coating. Results show improved performance with blends compared to neat fuel for all conditions of th...

  8. Field note: irrigation of tree stands with groundwater containing 1,4-dioxane.

    Science.gov (United States)

    Ferro, Ari M; Tammi, Carl E

    2009-07-01

    Coniferous and deciduous tree stands totaling 14 ha were recently planted on a closed landfill, and when mature, the stands are expected to be part of a natural treatment system for recovered groundwater. The trees would be irrigated at the rate of 189 L/min year-round with water containing 1,4-dioxane (trees. The water is moderately saline and contains elevated levels of manganese. This paper describes a concurrent series of preliminary studies, performed prior to the full-scale planting, to assess the feasibility of the phytoremediation system. Greenhouse experiments were carried out to identify tree species that can take up 1,4-dioxane and are tolerant of the water. Estimates were made of the area of the tree stand necessary to transpire the irrigation water plus precipitation. The landfill matrix was characterized in terms of its percolation rate and water holding capacity and based on those results salinity-modeling studies were carried out to estimate the fate and leaching potential of the various inorganic species that would accumulate in the root-zone of the trees. A pilot study, currently in progress on the landfill, suggested that the landfill cap is a suitable matrix for the establishment of large trees, and that the stands could be irrigated without the production of excess drainage.

  9. Degradation of 1,4-dioxane by biochar supported nano magnetite particles activating persulfate.

    Science.gov (United States)

    Ouyang, Da; Yan, Jingchun; Qian, Linbo; Chen, Yun; Han, Lu; Su, Anqi; Zhang, Wenying; Ni, Hao; Chen, Mengfang

    2017-10-01

    Nano magnetite biochar composite (nFe 3 O 4 /biochar) was synthesized and used to activate persulfate for the degradation of 1,4-dioxane. Analytical techniques using X-ray diffraction (XRD), fourier transform infrared analysis (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) indicated that nFe 3 O 4 was spherical and successfully loaded onto the surface of biochar. The results of batch-scale experiments illustrated that the 1,4-dioxane degradation efficiency in aqueous phase was 98.0% after 120 min reaction with the composite mass ratio of 1:1 between nFe 3 O 4 and the pine needle biochar pyrolyzed at 400 °C (P400) under the initial neutral pH. An electron paramagnetic resonance (EPR) study, free radical quenching experiment and XPS analysis were undertaken to illustrate the mechanism of persulfate activation by nFe 3 O 4 /biochar. Under acidic and neutral conditions, the predominant free radical was SO 4 - whereas OH and SO 4 - predominated when the initial pH was 9.0. The XPS analysis indicated that Fe(II) and oxygenated functional groups activated persulfate. In addition, carbon-carbon double bonds would be transformed into ketone and quinone which could activate persulfate during the reaction. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  10. Synthesis of benzyl chlorides and cycloveratrylene macrocycles using benzylic alcohols under homogeneous catalysis by HCl/dioxane

    Directory of Open Access Journals (Sweden)

    Yolanda Marina Vargas-Rodríguez

    2012-01-01

    Full Text Available The synthesis of benzyl chlorides, cyclic derivatives cyclotriveratrylene and cyclotripiperotrylene were carried out in using the HCl/dioxane system as a catalyst. The reaction proceeded with high selectivity and is sensitive to the number of alkyl and methoxy substituent on the aromatic ring.

  11. Kinetics and energy efficiency for the degradation of 1,4-dioxane by electro-peroxone process

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huijiao; Bakheet, Belal; Yuan, Shi; Li, Xiang; Yu, Gang [School of Environment, Tsinghua University, Beijing 100084 (China); Murayama, Seiichi [Power and Industrial Systems R& D Center, Toshiba Corporation, Fuchu-shi, Tokyo (Japan); Wang, Yujue, E-mail: wangyujue@tsinghua.edu.cn [School of Environment, Tsinghua University, Beijing 100084 (China)

    2015-08-30

    Highlights: • E-peroxone couples electrolysis with ozonation to driven peroxone reaction for pollutant degradation. • Significant amounts of ·OH can be efficiently produced in the E-peroxone process. • E-peroxone greatly enhances 1,4-dioxane degradation kinetics compared with ozonation and electrolysis. • E-peroxone consumes less energy for 1,4-dioxane mineralization than ozonation and electrolysis. • E-peroxone offers a cost-effective and energy-efficient alternative to degrade 1,4-dioxane. - Abstract: Degradation of 1,4-dioxane by ozonation, electrolysis, and their combined electro-peroxone (E-peroxone) process was investigated. The E-peroxone process used a carbon-polytetrafluorethylene cathode to electrocatalytically convert O{sub 2} in the sparged ozone generator effluent (O{sub 2} and O{sub 3} gas mixture) to H{sub 2}O{sub 2}. The electro-generated H{sub 2}O{sub 2} then react with sparged O{sub 3} to yield aqueous ·OH, which can in turn oxidize pollutants rapidly in the bulk solution. Using p-chlorobenzoic acid as ·OH probe, the pseudo-steady concentration of ·OH was determined to be ∼0.744 × 10{sup −9} mM in the E-peroxone process, which is approximately 10 and 186 times of that in ozonation and electrolysis using a Pt anode. Thanks to its higher ·OH concentration, the E-peroxone process eliminated 96.6% total organic carbon (TOC) from a 1,4-dioxane solution after 2 h treatment with a specific energy consumption (SEC) of 0.376 kWh g{sup −1} TOC{sub removed}. In comparison, ozonation and electrolysis using a boron-doped diamond anode removed only ∼6.1% and 26.9% TOC with SEC of 2.43 and 0.558 kWh g{sup −1} TOC{sub removed}, respectively. The results indicate that the E-peroxone process can significantly improve the kinetics and energy efficiency for 1,4-dioxane mineralization as compared to the two individual processes. The E-peroxone process may thus offer a highly effective and energy-efficient alternative to treat 1,4-dioxane

  12. Identification and characterization of 1,4-dioxane-degrading microbe separated from surface seawater by the seawater-charcoal perfusion apparatus.

    Science.gov (United States)

    Matsui, Ryotaro; Takagi, Kazuhiro; Sakakibara, Futa; Abe, Tomoko; Shiiba, Kiwamu

    2016-06-01

    To determine the concentration of soluble 1,4-dioxane during biodegradation, a new method using of high-performance liquid chromatography equipped with a hydrophilic interaction chromatography column was developed. The developed method enabled easy and rapid determination of 1,4-dioxane, even in saline medium. Microbes capable of degrading 1,4-dioxane were selected from the seawater samples by the seawater-charcoal perfusion apparatus. Among 32 candidate 1,4-dioxane degraders,, strain RM-31 exhibited the strongest 1,4-dioxane degradation ability. 16S rDNA sequencing and the similarity analysis of strain RM-31 suggested that this organism was most closely related to Pseudonocardia carboxydivorans. This species is similar to Pseudonocardia dioxanivorans, which has previously been reported as a 1,4-dioxane degrader. Strain RM-31 could degrade 300 mg/L within 2 days. As culture incubation times increasing, the residual 1,4-dioxane concentration was decreasing and the total protein contents extracted from growth cells were increasing. The optimum initial pH of the broth medium and incubation temperature for 1,4-dioxane degradation were pH 6-8 and 25 °C. The biodegradation rate of 1,4-dioxane by strain RM-31 at 25 °C in broth medium with 3 % NaCl was almost 20 % faster than that without NaCl. It was probably a first bacteria from the seawater that can exert a strong degrading ability.

  13. Dynamical (e,2e) studies of tetrahydropyran and 1,4-dioxane

    Energy Technology Data Exchange (ETDEWEB)

    Builth-Williams, J. D.; Chiari, L.; Jones, D. B., E-mail: darryl.jones@flinders.edu.au, E-mail: michael.brunger@flinders.edu.au [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, South Australia 5001 (Australia); Silva, G. B. da [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, South Australia 5001 (Australia); Universidade Federal de Mato Grosso, Barra do Garças, MT 78600-000 (Brazil); Chaluvadi, Hari; Madison, D. H. [Department of Physics, Missouri University of Science and Technology, Rolla, Missouri 65409 (United States); Brunger, M. J., E-mail: darryl.jones@flinders.edu.au, E-mail: michael.brunger@flinders.edu.au [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, South Australia 5001 (Australia); Institute of Mathematical Sciences, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2014-06-07

    We present experimental and theoretical results for the electron-impact ionization of the highest occupied molecular orbitals of tetrahydropyran and 1,4-dioxane. Using an (e,2e) technique in asymmetric coplanar kinematics, angular distributions of the slow ejected electron, with an energy of 20 eV, are measured when incident electrons at 250 eV ionize the target and scatter through an angle of either −10° or −15°. The data are compared with calculations performed at the molecular 3-body distorted wave level. Fair agreement between the theoretical model and the experimental measurements was observed. The similar structures for these targets provide key insights for assessing the limitations of the theoretical calculations. This study in turn facilitates an improved understanding of the dynamics in the ionization process.

  14. A general method for tritium labelling of benzimidazole carbamates by catalytic exchange in dioxane solutions

    Energy Technology Data Exchange (ETDEWEB)

    Lacey, E [Commonwealth Scientific and Industrial Research Organization, Glebe, NSW (Australia). Div. of Animal Health, McMaster Lab.; Dawson, M [Sydney Univ. (Australia). Dept. of Pharmacy; Long, M A; Than, C [New South Wales Univ., Kensington (Australia). School of Chemistry

    1989-12-01

    Benzimidazole carbamates (BZCs) act as inhibitors of the tubulin-microtubule equilibria in eukaryotic organisms. Recently drug resistance to this class of compounds in helminth parasites has been shown to be due to a reduced ability of resistant tubulin to bind BZCs. In order to quantitate the nature of the tubulin-BZC interaction a general method for the specific tritium labelling of BZCs has been developed. The BZCs: mebendazole, oxfendazole, parbendazole, oxibendazole, albendazole and fenbendazole were labelled by catalytic exchange using palladium on calcium carbonate in pure dioxane at 60{sup 0}C under tritium gas. The position of label incorporation for tritiated albendazole was determined by tritium-NMR as the 4-position of benzimadazole nucleus. The yields for individual BZCs varied from 8 to 68% for a range of specific activity of 0.44 to 13.4 Ci/mmole. (author).

  15. A general method for tritium labelling of benzimidazole carbamates by catalytic exchange in dioxane solutions

    International Nuclear Information System (INIS)

    Lacey, E.; Dawson, M.; Long, M.A.; Than, C.

    1989-01-01

    Benzimidazole carbamates (BZCs) act as inhibitors of the tubulin-microtubule equilibria in eukaryotic organisms. Recently drug resistance to this class of compounds in helminth parasites has been shown to be due to a reduced ability of resistant tubulin to bind BZCs. In order to quantitate the nature of the tubulin-BZC interaction a general method for the specific tritium labelling of BZCs has been developed. The BZCs: mebendazole, oxfendazole, parbendazole, oxibendazole, albendazole and fenbendazole were labelled by catalytic exchange using palladium on calcium carbonate in pure dioxane at 60 0 C under tritium gas. The position of label incorporation for tritiated albendazole was determined by tritium-NMR as the 4-position of benzimadazole nucleus. The yields for individual BZCs varied from 8 to 68% for a range of specific activity of 0.44 to 13.4 Ci/mmole. (author)

  16. Three-component synthesis of dialkyl 2-(alkylimino-methylene)3- (2,2,5-trimethyl-4,6-dioxo-1,3-dioxan-5-yl)-succinates.

    Science.gov (United States)

    Yavari, Issa; Zare, Hasan; Mohtat, Bita

    2006-05-01

    The adduct produced in the reaction between alkyl isocyanides and dialkyl acetylenedicarboxylates was trapped by 2,2,5-trimethyl-1,3-dioxane-4,6-dione (methyl Meldrum's acid), to afford highly functionalized ketenimines in good yields.

  17. Activation of cellulose by 1,4-dioxane for dissolution in N,N-dimethylacetamide/LiCl

    Czech Academy of Sciences Publication Activity Database

    Raus, Vladimír; Šturcová, Adriana; Dybal, Jiří; Šlouf, Miroslav; Vacková, Taťana; Šálek, Petr; Kobera, Libor; Vlček, Petr

    2012-01-01

    Roč. 19, č. 6 (2012), s. 1893-1906 ISSN 0969-0239 R&D Projects: GA ČR GAP108/12/0703; GA ČR GA106/09/1348 Institutional research plan: CEZ:AV0Z40500505 Institutional support: RVO:61389013 Keywords : cellulose activation * cellulose dissolution * 1,4-dioxane Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.476, year: 2012

  18. IMPLEMENTATION OF DIOXANE AND DIESEL FUEL BLENDS TO REDUCE EMISSION AND TO IMPROVE PERFORMANCE OF THE COMPRESSION IGNITION ENGINE

    Directory of Open Access Journals (Sweden)

    SENDILVELAN S.

    2017-11-01

    Full Text Available Performance of a compression ignition engine fuelled with 1, 4 Dioxane- diesel blends is evaluated. A single-cylinder, air-cooled, direct injection diesel engine developing a power output of 5.2 kW at 1500 rev/min is used. Base data is generated with standard diesel fuel subsequently; five fuel blends namely 90:10, 80:20, 70:30, 60:40 and 50:50 percentages by volume of diesel and dioxane were prepared and tested in the diesel engine. Engine performance and emission data were used to optimize the blends for reducing emission and improving performance. Results show improved performance with B10 blends compared to neat fuel for all conditions of the engine. Other blends recorded marginal decrease in brake thermal efficiency. The maximum efficiency for B30, B50 blends at peak load are 26.3%, 25.2% respectively against 29.1% for sole fuel. NOx emissions were found to be high or the blends. Peak pressure and rate of pressure rise are increased with increase in dioxane ratio due to improved combustion rate. Heat release pattern shows higher premixed combustion rate with the blends. Higher ignition delay and lower combustion duration are found with all blends than neat diesel fuel.

  19. Enthalpy-entropy compensation for the solubility of drugs in solvent mixtures: paracetamol, acetanilide, and nalidixic acid in dioxane-water.

    Science.gov (United States)

    Bustamante, P; Romero, S; Pena, A; Escalera, B; Reillo, A

    1998-12-01

    In earlier work, a nonlinear enthalpy-entropy compensation was observed for the solubility of phenacetin in dioxane-water mixtures. This effect had not been earlier reported for the solubility of drugs in solvent mixtures. To gain insight into the compensation effect, the behavior of the apparent thermodynamic magnitudes for the solubility of paracetamol, acetanilide, and nalidixic acid is studied in this work. The solubility of these drugs was measured at several temperatures in dioxane-water mixtures. DSC analysis was performed on the original powders and on the solid phases after equilibration with the solvent mixture. The thermal properties of the solid phases did not show significant changes. The three drugs display a solubility maximum against the cosolvent ratio. The solubility peaks of acetanilide and nalidixic acid shift to a more polar region at the higher temperatures. Nonlinear van't Hoff plots were observed for nalidixic acid whereas acetanilide and paracetamol show linear behavior at the temperature range studied. The apparent enthalpies of solution are endothermic going through a maximum at 50% dioxane. Two different mechanisms, entropy and enthalpy, are suggested to be the driving forces that increase the solubility of the three drugs. Solubility is entropy controlled at the water-rich region (0-50% dioxane) and enthalpy controlled at the dioxane-rich region (50-100% dioxane). The enthalpy-entropy compensation analysis also suggests that two different mechanisms, dependent on cosolvent ratio, are involved in the solubility enhancement of the three drugs. The plots of deltaH versus deltaG are nonlinear, and the slope changes from positive to negative above 50% dioxane. The compensation effect for the thermodynamic magnitudes of transfer from water to the aqueous mixtures can be described by a common empirical nonlinear relationship, with the exception of paracetamol, which follows a separate linear relationship at dioxane ratios above 50%. The

  20. Enzymes in Commercial Cellulase Preparations Bind Differently to Dioxane Extracted Lignins

    Energy Technology Data Exchange (ETDEWEB)

    Yarbrough, John M.; Mittal, Ashutosh; Katahira, Rui; Mansfield, Elisabeth; Taylor, Larry E.; Decker, Stephen R.; Himmel, Michael E.; Vinzant, Todd

    2017-04-24

    Commercial fungal cellulases used in biomass-to-biofuels processes can be grouped into three general classes: native, augmented, and engineered. To evaluate lignin binding affinities of different enzyme activities in various commercial cellulase formulations in order to determine if enzyme losses due to lignin binding can be modulated by using different enzymes of the same activity We used water:dioxane (1:9) to extract lignin from pretreated corn stover. Commercial cellulases were incubated with lignin and the unbound supernatants were evaluated for individual enzyme loss by SDS=PAGE and these were correlated with activity loss using various pNP-sugar substrates. Colorimetric assays for general glycosyl hydrolase activities showed distinct differences in enzyme binding to lignin for each enzyme activity. Native systems demonstrated low binding of endo- and exo-cellulases, high binding of xylanase, and moderate ..beta..-glucosidase binding. Engineered cellulase mixtures exhibited low binding of exo-cellulases, very strong binding of endocellulases and ..beta..- glucosidase, and mixed binding of xylanase activity. The augmented cellulase had low binding of exocellulase, high binding of endocellulase and xylanase, and moderate binding of ..beta..-glucosidase activities. Bound and unbound activities were correlated with general molecular weight ranges of proteins as measured by loss of proteins bands in bound fractions on SDS-PAGE gels. Lignin-bound high molecular weight bands correlated with binding of ..beta..-glucosidase activity. While ..beta..-glucosidases demonstrated high binding in many cases, they have been shown to remain active. Bound low molecular weight bands correlated with xylanase activity binding. Contrary to other literature, exocellulase activity did not show strong lignin binding. The variation in enzyme activity binding between the three classes of cellulases preparations indicate that it is certainly possible to alter the binding of specific

  1. Method development for the analysis of 1,4-dioxane in drinking water using solid-phase extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Grimmett, Paul E; Munch, Jean W

    2009-01-01

    1,4-Dioxane has been identified as a probable human carcinogen and an emerging contaminant in drinking water. The United States Environmental Protection Agency's (U.S. EPA) National Exposure Research Laboratory (NERL) has developed a method for the analysis of 1,4-dioxane in drinking water at ng/L concentrations. The method consists of an activated carbon solid-phase extraction of 500-mL or 100-mL water samples using dichloromethane as the elution solvent. The extracts are analyzed by gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode. In the NERL laboratory, recovery of 1,4-dioxane ranged from 94-110% in fortified laboratory reagent water and recoveries of 96-102% were demonstrated for fortified drinking water samples. The relative standard deviations for replicate analyses were less than 6% at concentrations exceeding the minimum reporting level.

  2. Acoustical Studies of Some Schiff Bases in 1,4-Dioxane and Dimethylformamide at 318.15 K

    Institute of Scientific and Technical Information of China (English)

    BALUJA Shipra

    2006-01-01

    From experimental data of density, viscosity and ultrasonic velocity, the various acoustical properties, such as specific impedance (Z), isentropic compressibility (κs), Rao's molar sound function (Rm), the van der Waals constant (b), molar compressibility (W), intermolecular free length (Lf), relaxation strength (r), internal pressure (π),free volume (Vf), solvation number (Sn) etc., were calculated for three Schiff bases in 1,4-dioxane and dimethylformamide (DMF) at 318.15 K. The results are interpreted in terms of molecular interactions occurring in the solutions.

  3. Thermodynamic models for determination of 3-chloro-N-phenylphthalimide solubility in binary solvent mixtures of (acetone, ethyl acetate or 1,4-dioxane + methanol)

    International Nuclear Information System (INIS)

    Xie, Yong; Shi, Hongwei; Du, Cunbin; Cong, Yang; Wang, Jian; Zhao, Hongkun

    2016-01-01

    Highlights: • Solubility of 3-chloro-N-phenylphthalimide in binary mixed solvents were determined. • Solubility data were correlated and calculated by five models. • The standard molar enthalpy for the dissolution processes were calculated. - Abstract: The solubility of 3-chloro-N-phenylphthalimide in binary mixed solvents of (acetone + methanol, ethyl acetate + methanol and 1,4-dioxane + methanol) were determined experimentally by using the isothermal dissolution equilibrium method within the temperature range from (288.15 to 323.15) K under atmosphere pressure. For the binary systems of (acetone + methanol) and (1,4-dioxane + methanol), the solubility of 3-chloro-N-phenylphthalimide increased with increasing temperature and mass fraction of acetone or 1,4-dioxane; and for the (ethyl acetate + methanol) system, at a given composition of ethyl acetate, the solubility of 3-chloro-N-phenylphthalimide increased with an increase in temperature; nevertheless at the same temperature, they increased at first and then decreased with increasing mass fraction of 1,4-dioxane. At the same temperature and mass fraction of acetone, ethyl acetate or 1,4-dioxane, the solubility of 3-chloro-N-phenylphthalimide was greater in (1,4-dioxane + methanol) than in the other two mixed solvents. The solubility values were correlated by employing the Jouyban–Acree model, van’t Hoff–Jouyban–Acree model, Apelblat–Jouyban–Acree model, Ma model, and Sun model. On the whole, the Ma model and Sun model were proven to provide good representation of the experimental solubility results. Furthermore, the dissolution enthalpies of the dissolution process were calculated. The dissolution process of 3-chloro-N-phenylphthalimide in these mixed solvents is endothermic. The experimental solubility and the models in this study could be helpful in purifying 3-chloro-N-phenylphthalimide.

  4. Solubility and phase separation of 4-morpholinepropanesulfonic acid (MOPS), and 3-morpholino-2-hydroxypropanesulfonic acid (MOPSO) in aqueous 1,4-dioxane and ethanol solutions

    International Nuclear Information System (INIS)

    Taha, Mohamed; Lee, Ming-Jer

    2011-01-01

    Highlights: → Solubilities of MOPS and MOPSO buffers in aqueous 1,4-dioxane and ethanol solutions. → We found that MOPS-induced phase separation of aqueous solution of 1,4-dioxane. → The phase diagram of (MOPS + water + 1,4-dioxane) system at 298.15 K is documented. → The tie-lines within the two-liquid phase region were also determined at 298.15 K. → The effective excluded volume theory was applied to correlate the binodal LLE data. - Abstract: The buffers 4-morpholinepropanesulfonic acid (MOPS) and 3-morpholino-2-hydroxypropanesulfonic acid (MOPSO) are useful biological zwitterionic buffers within the pH range of 6.5 to 7.9 and 6.2 to 7.6, respectively. The solubilities of these buffers were determined in binary mixtures (1,4-dioxane + water) and (ethanol + water) at T = 298.15 K by using the results of density measurements. It has been observed that MOPS induced liquid-liquid phase splitting for the mixtures of 40% to 90% (w/w) 1,4-dioxane in water. The two-liquid phase formation was visualized with disperse orange 25. The phase equilibrium boundaries, including the regions of one liquid, two liquids, (one liquid + one solid) and (two liquids + one solid), for the (MOPS + water + 1,4-dioxane) system have been determined experimentally at T = 298.15 K. The tie lines of the (liquid + liquid) equilibrium were also measured. The Othmer-Tobias and Bancroft equation were used to evaluate the reliability of the tie-line data. The binodal curve was fitted to an empirical equation and the effective excluded volume (EEV) model. The apparent free energies of transfer (ΔG tr ' ) of MOPS and MOPSO from water to 1,4-dioxane and ethanol solutions have been calculated from the solubility data. These ΔG tr ' values were compared with those of some related biological buffers (TRIS, TAPS, TAPSO, and TABS). Furthermore, we also calculated the contribution of transfer free energies (Δg tr ' ) of -OH group from water to 1,4-dioxane and ethanol solutions.

  5. PERFORMANCE ANALYSIS OF 1,4 DIOXANE-ETHANOL-DIESEL BLENDS ON DIESEL ENGINES WITH AND WITHOUT THERMAL BARRIER COATING

    Directory of Open Access Journals (Sweden)

    Chockalingam Sundar Raj

    2010-01-01

    Full Text Available 1,4 dioxane, a new additive allows the splash blending of ethanol in diesel in a clear solution. The objective of this investigation is to first create a stable ethanol-diesel blended fuel with 10% 1,4 dioxane additive, and then to generate performance, combustion and emissions data for evaluation of different ethanol content on a single cylinder diesel engine with and without thermal barrier coating. Results show improved performance with blends compared to neat fuel for all conditions of the engine. Drastic reduction in smoke density is found with the blends as compared to neat diesel and the reduction is still better for coated engine. NOx emissions were found to be high for coated engines than the normal engine for the blends. The oxygen enriched fuel increases the peak pressure and rate of pressure rise with increase in ethanol ratio and is still superior for coated engine. Heat release pattern shows higher premixed combustion rate with the blends. Longer ignition delay and shorter combustion duration are found with all blends than neat diesel fuel.

  6. Spectroscopic methods for aqueous cyclodextrin inclusion complex binding measurement for 1,4-dioxane, chlorinated co-contaminants, and ozone

    Science.gov (United States)

    Khan, Naima A.; Johnson, Michael D.; Carroll, Kenneth C.

    2018-03-01

    Recalcitrant organic contaminants, such as 1,4-dioxane, typically require advanced oxidation process (AOP) oxidants, such as ozone (O3), for their complete mineralization during water treatment. Unfortunately, the use of AOPs can be limited by these oxidants' relatively high reactivities and short half-lives. These drawbacks can be minimized by partial encapsulation of the oxidants within a cyclodextrin cavity to form inclusion complexes. We determined the inclusion complexes of O3 and three common co-contaminants (trichloroethene, 1,1,1-trichloroethane, and 1,4-dioxane) as guest compounds within hydroxypropyl-β-cyclodextrin. Both direct (ultraviolet or UV) and competitive (fluorescence changes with 6-p-toluidine-2-naphthalenesulfonic acid as the probe) methods were used, which gave comparable results for the inclusion constants of these species. Impacts of changing pH and NaCl concentrations were also assessed. Binding constants increased with pH and with ionic strength, which was attributed to variations in guest compound solubility. The results illustrate the versatility of cyclodextrins for inclusion complexation with various types of compounds, binding measurement methods are applicable to a wide range of applications, and have implications for both extraction of contaminants and delivery of reagents for treatment of contaminants in wastewater or contaminated groundwater.

  7. Molecular Interactions in 1,4-Dioxane, Tetrahydrofuran, and Ethyl Acetate Solutions of 1,1'-Bis(4-isopropyloxyacetylphenoxy)cyclohexane on Reological, Density, and Acoustic Behavior

    Science.gov (United States)

    Dhaduk, B. B.; Patel, Ch. B.; Parsania, P. H.

    2017-12-01

    Various thermo-acoustical parameters of 1,4-dioxane, tetrahydofuran and ethylacetae solutions of 1,1'-bis(4-isopropyloxyacetylphenoxy)cyclohexane were determined at different temperatures using density, viscosity and ultrasonic speed and correlated with concentration. Linear increase of ultrasonic speed, specific acoustical impedance, Rao's molar sound function, Van der Waals constant and free volume with concentration C and decreased with temperature. Linear decrease of adiabatic compressibility, internal pressure, intermolecular free path length, classical absorption coefficient, and viscous relaxation time with concentration and increased with temperature indicated existence of strong molecular interactions in solutions and further supported by positive values of solvation number. Gibbs free energy of activation decreased with C in all three systems. It is decreased with T in 1,4-dioxane, while increased in tetrahydrofuran and ethyl acetate. Both enthalpy of activation and entropy of activation are increased gradually with C in 1,4-dioxane, while they are negative and remained practically independent of concentration in 1,4-dioxane and tetrahydofuran systems.

  8. Influence of Conductivity and Dielectric Constant of Water–Dioxane Mixtures on the Electrical Response of SiNW-Based FETs

    NARCIS (Netherlands)

    Mescher, M.; Brinkman, A.G.M.; Bosma, D.; Klootwijk, J.H.; Sudhölter, E.J.R.; De Smet, L.C.P.M.

    2014-01-01

    In this study, we report on the electrical response of top-down, p-type silicon nanowire field-effect transistors exposed to water and mixtures of water and dioxane. First, the capacitive coupling of the back gate and the liquid gate via an Ag/AgCl electrode were compared in water. It was found that

  9. Concentration and trend of 1,4-dioxane in wells sampled during 2002–2017 in the vicinity of the Tucson International Airport Area Superfund Site, Arizona

    Science.gov (United States)

    Tillman, Fred D.

    2017-09-25

    Industrial activities causing extensive groundwater contamination led to the listing of the Tucson International Airport Area (TIAA) as a Superfund Site in 1983. Early groundwater investigations identified volatile organic compounds (VOCs), including the chlorinated solvents trichloroethylene (TCE) and perchloroethylene (PCE), in wells in the area. Several responsible parties were identified and cleanup activities began in the late 1980s. In 2002, the compound 1,4-dioxane was discovered in wells in the area and has since been detected in measurable concentrations throughout the site. The U.S. Environmental Protection Agency (USEPA) classifies 1,4-dioxane as a likely human carcinogen.The purpose of this map is to present 1,4-dioxane concentrations in wells sampled from 2002 through mid-2017 in the TIAA Superfund Site area to indicate both the current status and trends in 1,4-dioxane groundwater contamination. This map includes data from wells in the commercial and residential community in the TIAA and does not include data from wells in suspected or confirmed source areas, such as Air Force Plant 44 and Tucson International Airport, or from wells within treatment facilities.

  10. Synthesis of Novel Homo-N-Nucleoside Analogs Composed of a Homo-1,4-Dioxane Sugar Analog and Substituted 1,3,5-Triazine Base Equivalents

    Directory of Open Access Journals (Sweden)

    Qiang Yu

    2008-12-01

    Full Text Available Enantioselective syntheses from dimethyl tartrate of 1,3,5-triazine homo-N-nucleoside analogs, containing a 1,4-dioxane moiety replacing the sugar unit in natural nucleosides, were accomplished. The triazine heterocycle in the nucleoside analogs was further substituted with combinations of NH2, OH and Cl in the 2,4-triazine positions.

  11. Effect of dioxan and toluene as solvents on: Polycondensation leading to poly (2.5-furylene vinylene)s

    International Nuclear Information System (INIS)

    Al-Hariri, S. N.

    2008-01-01

    This paper describes the influence of two different solvents, on a synthetic route leading to linear poly (2.5-furylene vinylene)s PFV, which involves the polycondensation of 5-methyl furfural in a basic medium, and on the characterization of PFV. The replacement of benzene by dioxan gives a linear polymeric structure possessing a high degree of conjugation, a good degree of polymerization, a remarkable stability to storage under ordinary condition and a partial solubility in common solvents, especially methylene chloride. Casting films from solution polymer gives brittle material, without any mechanical strength. However, the product obtained by using the toluene differs from the expected polymer. The results indicate that the raising of the degree of polymerization was done by increasing the time of reaction and successively introducing the monomer. Monomer, and dimer are isolated and characterized from the sub-product (oligomer) of the reaction. (author)

  12. Simultaneous Transformation of Commingled Trichloroethylene, Tetrachloroethylene, and 1,4-Dioxane by a Microbially Driven Fenton Reaction in Batch Liquid Cultures

    Science.gov (United States)

    Sekar, Ramanan; Taillefert, Martial

    2016-01-01

    ABSTRACT Improper disposal of 1,4-dioxane and the chlorinated organic solvents trichloroethylene (TCE) and tetrachloroethylene (also known as perchloroethylene [PCE]) has resulted in widespread contamination of soil and groundwater. In the present study, a previously designed microbially driven Fenton reaction system was reconfigured to generate hydroxyl (HO˙) radicals for simultaneous transformation of source zone levels of single, binary, and ternary mixtures of TCE, PCE, and 1,4-dioxane. The reconfigured Fenton reaction system was driven by fed batch cultures of the Fe(III)-reducing facultative anaerobe Shewanella oneidensis amended with lactate, Fe(III), and contaminants and exposed to alternating anaerobic and aerobic conditions. To avoid contaminant loss due to volatility, the Fe(II)-generating, hydrogen peroxide-generating, and contaminant transformation phases of the microbially driven Fenton reaction system were separated. The reconfigured Fenton reaction system transformed TCE, PCE, and 1,4-dioxane either as single contaminants or as binary and ternary mixtures. In the presence of equimolar concentrations of PCE and TCE, the ratio of the experimentally derived rates of PCE and TCE transformation was nearly identical to the ratio of the corresponding HO˙ radical reaction rate constants. The reconfigured Fenton reaction system may be applied as an ex situ platform for simultaneous degradation of commingled TCE, PCE, and 1,4-dioxane and provides valuable information for future development of in situ remediation technologies. IMPORTANCE A microbially driven Fenton reaction system [driven by the Fe(III)-reducing facultative anaerobe S. oneidensis] was reconfigured to transform source zone levels of TCE, PCE, and 1,4-dioxane as single contaminants or as binary and ternary mixtures. The microbially driven Fenton reaction may thus be applied as an ex situ platform for simultaneous degradation of at least three (and potentially more) commingled contaminants

  13. A potentiometric study of molecular heteroconjugation equilibria in (n-butylamine+acetic acid) systems in binary (acetonitrile +1,4-dioxane) solvent mixtures

    International Nuclear Information System (INIS)

    Czaja, Malgorzata; Makowski, Mariusz; Chmurzynski, Lech

    2006-01-01

    By using the potentiometric method the following quantities have been determined: acidity constants of molecular acid, K a (HA), of cationic acid, K a (BH + ), anionic and cationic homoconjugation constants, K AHA - and K BHB + , respectively, as well as molecular heteroconjugation constants, K AHB , in (n-butylamine+acetic acid) systems without proton transfer in binary (acetonitrile+1,4-dioxane), AN+D, solvent mixtures. The results of these measurements have shown that the magnitudes of the molecular heteroconjugation constants do not depend on the 1,4-dioxane content in the mixed solvent, i.e., on solvent polarity. It has also been found that in the (acid+base) systems without proton transfer, the manner of carrying out the titration (direct B+HA vs. reverse HA+B) does not affect the magnitudes of the molecular heteroconjugation constants

  14. A potentiometric study of molecular heteroconjugation equilibria in (n-butylamine+acetic acid) systems in binary (acetonitrile +1,4-dioxane) solvent mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Czaja, Malgorzata [Department of General Chemistry, University of Gdansk, Sobieskiego 18, 80-952 Gdansk (Poland); Makowski, Mariusz [Department of General Chemistry, University of Gdansk, Sobieskiego 18, 80-952 Gdansk (Poland); Chmurzynski, Lech [Department of General Chemistry, University of Gdansk, Sobieskiego 18, 80-952 Gdansk (Poland)]. E-mail: lech@chem.univ.gda.pl

    2006-05-15

    By using the potentiometric method the following quantities have been determined: acidity constants of molecular acid, K{sub a}(HA), of cationic acid, K{sub a}(BH{sup +}), anionic and cationic homoconjugation constants, K{sub AHA{sup -}} and K{sub BHB{sup +}}, respectively, as well as molecular heteroconjugation constants, K{sub AHB}, in (n-butylamine+acetic acid) systems without proton transfer in binary (acetonitrile+1,4-dioxane), AN+D, solvent mixtures. The results of these measurements have shown that the magnitudes of the molecular heteroconjugation constants do not depend on the 1,4-dioxane content in the mixed solvent, i.e., on solvent polarity. It has also been found that in the (acid+base) systems without proton transfer, the manner of carrying out the titration (direct B+HA vs. reverse HA+B) does not affect the magnitudes of the molecular heteroconjugation constants.

  15. Developing and Validating Genetic Catabolic Probes for Monitored Natural Attenuation of 1,4-Dioxane with a One-Year Timeframe

    Science.gov (United States)

    2014-04-01

    exceeds root penetration and hinders the feasibility of phytoremediation . Furthermore, dioxane’s heterocyclic ether structure makes it recalcitrant...keto-1,4- dioxane, which is cleaved by a hydrolase or a spontaneous decomposition [44, 50]. 8 CB1190 has been used to augment phytoremediation ...Scientific, Fair Lawn, NJ. Anhydrous sodium sulfate and anhydrous mercury chloride were purchased from Thermo Fisher Scientific, Waltham, MA. 16

  16. About the singular behavior of the ionic condensation of sodium chondroitin sulfate: Conductivity study in water and water dioxane mixture

    Science.gov (United States)

    M'halla, Jalel; Besbes, Rafik; Bouazzi, Ramzi; Boughammoura, Sondes

    2006-01-01

    sulfate in water ( bS = 5.72 Å). The addition of dioxane increases Lb, consequently, α is shifted from its Manning's value. In order to verify this dioxane effect, we have compared experimental equivalent conductibilities Λexp of sodium chondroitin sulfate in water ( no shift) and water-dioxane (60 wt%) mixture ( positive shift), to their theoretical values ΛM, ΛcthandΛsth corresponding, respectively, to the Manning, cylindrical and spherical models. This comparison allows also, to explain the conformation "chosen" by the polyion, in order to minimizing the friction effects (due to: viscosity; ionic and dielectric relaxations) and therefore, to optimize its mobility by the shift of its rate of ionic condensation α.

  17. The synthesis and the spectroscopic, thermal, and structural properties of the M2[(fumarate)Ni(CN)4]·2(1,4-Dioxane) clathrate (M = Co, Ni, Cd and Hg)

    Science.gov (United States)

    Kartal, Zeki; Yavuz, Abdülkerim

    2018-03-01

    In this study, the clathrates of fumarate-tetracyanonickel-dioxane, given by the formula M2[(fumarate)Ni(CN)4]·2(1,4-Dioxane) (M = Co, Ni, Cd and Hg), have been obtained for the first time through chemical methods. These clathrates have been characterized by elemental, thermal, FT-IR, and FT-Raman spectroscopies. The parameters of structures of clathrates have been determined by X-ray powder diffraction. The thermal behaviors of these clathrates have been also investigated by thermo-gravimetric analysis (TGA), differential thermal analysis (DTA), and derivative thermal gravimetric analysis (DTG) in the range of 20-900 °C. X-ray powder diffraction data have been recorded at ambient temperature in the 2θ range 5-50°. The FT-IR and FT-Raman spectra of clathrates have been recorded in the region of 4000-400 cm-1 and 4000-100 cm-1, respectively. The results of the spectral and thermal analyses of the newly synthesized clathrates of fumarate-tetracyanonickel-dioxane suggest that these clathrates are new examples of the Hofmann-type dioxane clathrates. In our study, the Hofmann-type dioxane clathrates, which are formed by bounding electrons of oxygen-donor atoms of fumarate ion ligand molecule to transition metal atoms, consist of the corrugated |M-Ni(CN)4|∞ polymeric layers, which are held in parallel through the chain of (-M-fumarate-M-).

  18. Potential for cometabolic biodegradation of 1,4-dioxane in aquifers with methane or ethane as primary substrates.

    Science.gov (United States)

    Hatzinger, Paul B; Banerjee, Rahul; Rezes, Rachael; Streger, Sheryl H; McClay, Kevin; Schaefer, Charles E

    2017-12-01

    The objective of this research was to evaluate the potential for two gases, methane and ethane, to stimulate the biological degradation of 1,4-dioxane (1,4-D) in groundwater aquifers via aerobic cometabolism. Experiments with aquifer microcosms, enrichment cultures from aquifers, mesophilic pure cultures, and purified enzyme (soluble methane monooxygenase; sMMO) were conducted. During an aquifer microcosm study, ethane was observed to stimulate the aerobic biodegradation of 1,4-D. An ethane-oxidizing enrichment culture from these samples, and a pure culture capable of growing on ethane (Mycobacterium sphagni ENV482) that was isolated from a different aquifer also biodegraded 1,4-D. Unlike ethane, methane was not observed to appreciably stimulate the biodegradation of 1,4-D in aquifer microcosms or in methane-oxidizing mixed cultures enriched from two different aquifers. Three different pure cultures of mesophilic methanotrophs also did not degrade 1,4-D, although each rapidly oxidized 1,1,2-trichloroethene (TCE). Subsequent studies showed that 1,4-D is not a substrate for purified sMMO enzyme from Methylosinus trichosporium OB3b, at least not at the concentrations evaluated, which significantly exceeded those typically observed at contaminated sites. Thus, our data indicate that ethane, which is a common daughter product of the biotic or abiotic reductive dechlorination of chlorinated ethanes and ethenes, may serve as a substrate to enhance 1,4-D degradation in aquifers, particularly in zones where these products mix with aerobic groundwater. It may also be possible to stimulate 1,4-D biodegradation in an aerobic aquifer through addition of ethane gas. Conversely, our results suggest that methane may have limited importance in natural attenuation or for enhancing biodegradation of 1,4-D in groundwater environments.

  19. Crystal structures of the dioxane hemisolvates of N-(7-bromomethyl-1,8-naphthyridin-2-ylacetamide and bis[N-(7-dibromomethyl-1,8-naphthyridin-2-ylacetamide

    Directory of Open Access Journals (Sweden)

    Robert Rosin

    2017-10-01

    Full Text Available The syntheses and crystal structures of N-(7-bromomethyl-1,8-naphthyridin-2-ylacetamide dioxane hemisolvate, C11H10BrN3O·0.5C4H8O2, (I, and bis[N-(7-dibromomethyl-1,8-naphthyridin-2-ylacetamide] dioxane hemisolvate, 2C11H9Br2N3O·0.5C4H8O2, (II, are described. The molecules adopt a conformation with the N—H hydrogen pointing towards the lone electron pair of the adjacent naphthyridine N atom. The crystals of (I are stabilized by a three-dimensional supramolecular network comprising N—H...N, C—H...N and C—H...O hydrogen bonds, as well as C—Br...π halogen bonds. The crystals of compound (II are stabilized by a three-dimensional supramolecular network comprising N—H...N, C—H...N and C—H...O hydrogen bonds, as well as C—H...π contacts and C—Br...π halogen bonds. The structure of the substituent attached in the 7-position of the naphthyridine skeleton has a fundamental influence on the pattern of intermolecular noncovalent bonding. While the Br atom of (I participates in weak C—Br...Oguest and C—Br...π contacts, the Br atoms of compound (II are involved in host–host interactions via C—Br...O=C, C—Br...N and C—Br...π bonding.

  20. Correct liquid scintillation counting of steroids and glycosides in RIA samples: a comparison of xylene-based, dioxane-based and colloidal counting systems. Chapter 14

    International Nuclear Information System (INIS)

    Spolders, H.

    1977-01-01

    In RIA, the following parameters are important for accurate liquid scintillation counting. (1) Absence of chemiluminescence. (2) Stability of count rate. (3) Dissolving properties for the sample. For samples with varying colours, a quench correction must be applied. For any type of accurate quench correction, a homogeneous sample is necessary. This can be obtained if proteins and the buffer can be dissolved completely in the scintillator solution. In this paper, these criteria are compared in xylene-based, dioxane-based and colloidal scintillation solutions for either bound or free antigens of different polarity. The labelling radioisotope used was 3 H. Using colloidal scintillators with plasma and buffer samples, phasing or sedimentation of salt or proteins sometimes occurs. The influence of sedimentation or phasing on count rate stability and correct quench correction is illustrated by varying the ratio between the scintillator solution and a RIA sample containing a semi-polar steroid aldosterone. (author)

  1. Densities and viscosities of binary and ternary mixtures of cyclohexanone, 1,4-dioxane and isooctane from T = (288.15 to 313.15) K

    International Nuclear Information System (INIS)

    Rafiee, Hamid Reza; Ranjbar, Shahram; Poursalman, Fariborz

    2012-01-01

    Graphical abstract: For binary and ternary mixtures of the following liquids the densities and viscosities have been determined at several temperatures and over the entire range of composition. Also the Δη and excess molar volumes for binary mixtures determined and have been fitted to the Redlich–Kister equation. The interaction parameters, G 12 in the Grunberg–Nissan equation have been found to be negative for all binary mixtures which indicates decreasing the interaction between unlike molecules. Highlights: ► Experimental data for viscosity and density of binary and ternary mixtures reported. ► The considered solvents are Cyclohexanone, 1,4-Dioxane and Isooctane. ► Temperature ranges from 288.15 to 313.15 K and entire range of composition is considered. ► G 12 , in Grunberg–Nissan equation was negative in all binary mixtures at all temperatures. ► V E and Δη for binary mixtures have been fitted to Redlich–Kister equation. - Abstract: Densities and viscosities of binary and ternary mixtures of cyclohexanone, 1,4-dioxane and isooctane have been measured at temperatures from 288.15 K to 313.15 K and over the entire composition range, under atmospheric pressure. From these binary data, the excess molar volumes have been determined and then fitted to Redlich–Kister equation to determine the appropriate coefficients. This work also provides a test of the Grunberg and Nissan equation for correlation the dynamic viscosities of binary mixtures with mole fractions. The interaction parameters for this equation, G 12 were negative for all binary mixtures at different temperatures over entire range of composition which attributed to decreasing the strength of interaction between unlike molecules in mixture.

  2. Studies on the self-catalyzed Knoevenagel condensation, characterization, DPPH radical scavenging activity, cytotoxicity, and molecular properties of 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones using single crystal XRD and DFT techniques

    Science.gov (United States)

    Suresh Kumar, G. S.; Antony Muthu Prabhu, A.; Bhuvanesh, N.

    2014-10-01

    We have studied the self-catalyzed Knoevenagel condensation, spectral characterization, DPPH radical scavenging activity, cytotoxicity, and molecular properties of 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones using single crystal XRD and DFT techniques. In the absence of any catalyst, a series of novel 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones were synthesized using Meldrum’s acid and formylphenoxyaliphatic acid(s) in water. These molecules are arranged in the dimer form through intermolecular H-bonding in the single crystal XRD structure. Compounds have better DPPH radical scavenging activity and cytotoxicity against A431 cancer cell line. The optimized molecular structure, natural bond orbital analysis, electrostatic potential map, HOMO-LUMO energies, molecular properties, and atomic charges of these molecules have been studied by performing DFT/B3LYP/3-21G(*) level of theory in gas phase.

  3. Endoperoxide polyketides from a Chinese Plakortis simplex: further evidence of the impact of stereochemistry on antimalarial activity of simple 1,2-dioxanes.

    Science.gov (United States)

    Chianese, Giuseppina; Persico, Marco; Yang, Fan; Lin, Hou-Wen; Guo, Yue-Wei; Basilico, Nicoletta; Parapini, Silvia; Taramelli, Donatella; Taglialatela-Scafati, Orazio; Fattorusso, Caterina

    2014-09-01

    Chemical investigation of the organic extract obtained from the sponge Plakortis simplex collected in the South China Sea afforded five new polyketide endoperoxides (2 and 4-7), along with two known analogues (1 and 3). The stereostructures of these metabolites have been deduced on the basis of spectroscopic analysis and chemical conversion. The isolated endoperoxide derivatives have been tested for their in vitro antimalarial activity against Plasmodium falciparum strains, showing IC50 values in the low micromolar range. The structure-activity relationships were analyzed by means of a detailed computational investigation and rationalized in the light of the mechanism of action proposed for this class of simple antimalarials. The relative orientation of the atoms involved in the putative radical generation and transfer reaction was demonstrated to have a great impact on the antimalarial activity. The resulting 3D pharmacophoric model can be a useful guide to design simple and effective antimalarial lead compounds belonging to the class of 1,2-dioxanes. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Photolysis of Mono- and Dichloramines in UV/Hydrogen Peroxide: Effects on 1,4-Dioxane Removal and Relevance in Water Reuse.

    Science.gov (United States)

    Patton, Samuel; Romano, Mariano; Naddeo, Vincenzo; Ishida, Kenneth P; Liu, Haizhou

    2018-06-05

    Growing demands and increasing scarcity of fresh water resources necessitate potable water reuse, which has been implemented with the aid of UV-based advanced oxidation processes (UV/AOPs) that remove potentially hazardous trace organic contaminants from reclaimed water. During the potable reuse treatment process, chloramines are added to prevent membrane fouling that are carried over to the UV/AOP, where hydrogen peroxide (H 2 O 2 ) is commonly added. However, the impact of chloramines on the photolysis of H 2 O 2 and the overall performance of the UV/AOP remains unknown. This study investigated the impacts of the photochemistry of monochloramine (NH 2 Cl) and dichloramine (NHCl 2 ) associated with the photolysis of H 2 O 2 on the degradation of 1,4-dioxane (1,4-D), a trace organic contaminant ubiquitous in recycled water. Results indicated that NH 2 Cl and NHCl 2 alone functioned as oxidants upon UV photolysis, which produced HO • and Cl 2 •- as the two primary oxidative radicals. The speciation of chloramines did not have a significant impact on the degradation kinetics. The inclusion of monochloramine in UV/H 2 O 2 greatly decreased 1,4-D removal efficiency. HO • was the major radical in the mixed H 2 O 2 /chloramine system. Results from this study suggest that recognizing the existence of chloramines in UV/H 2 O 2 systems is important for predicting UV/AOP performance in the treatment train of potable reuse.

  5. Experimental Investigation and Thermodynamic Assessment of Phase Equilibria in the PLLA/Dioxane/Water Ternary System for Applications in the Biomedical Field.

    Science.gov (United States)

    Ruggiero, Flavia; Netti, Paolo Antonio; Torino, Enza

    2015-12-01

    Fundamental understanding of thermodynamic of phase separation plays a key role in tuning the desired features of biomedical devices. In particular, phase separation of ternary solution is of remarkable interest in processes to obtain biodegradable and biocompatible architectures applied as artificial devices to repair, replace, or support damaged tissues or organs. In these perspectives, thermally induced phase separation (TIPS) is the most widely used technique to obtained porous morphologies and, in addition, among different ternary systems, polylactic acid (PLLA)/dioxane/water has given promising results and has been largely studied. However, to increase the control of TIPS-based processes and architectures, an investigation of the basic energetic phenomena occurring during phase separation is still required. Here we propose an experimental investigation of the selected ternary system by using isothermal titration calorimetric approach at different solvent/antisolvent ratio and a thermodynamic explanation related to the polymer-solvents interactions in terms of energetic contribution to the phase separation process. Furthermore, relevant information about the phase diagrams and interaction parameters of the studied systems are furnished in terms of liquid-liquid miscibility gap. Indeed, polymer-solvents interactions are responsible for the mechanism of the phase separation process and, therefore, of the final features of the morphologies; the knowledge of such data is fundamental to control processes for the production of membranes, scaffolds and several nanostructures. The behavior of the polymer at different solvent/nonsolvent ratios is discussed in terms of solvation mechanism and a preliminary contribution to the understanding of the role of the hydrogen bonding in the interface phenomena is also reported. It is the first time that thermodynamic data of a ternary system are collected by mean of nano-isothermal titration calorimetry (nano-ITC). Supporting

  6. Densities and speeds of sound for binary mixtures of (1,3-dioxolane or 1,4-dioxane) with (2-methyl-1-propanol or 2-methyl-2-propanol) at the temperatures (298.15 and 313.15) K

    International Nuclear Information System (INIS)

    Villares, A.; Martin, S.; Haro, M.; Giner, B.; Artigas, H.

    2004-01-01

    This paper reports densities and speeds of sound for the binary mixtures of (1,3-dioxolane or 1,4-dioxane) with (2-methyl-1-propanol or 2-methyl-2-propanol) at the temperatures (298.15 and 313.15) K. Excess volumes and excess isentropic compressibility coefficients have been calculated from experimental data and fitted by means of a Redlich-Kister type equation. The ERAS model has been used to calculate the excess volumes of the four systems at both temperatures

  7. Hythane (H2 and CH4) production from unsaturated polyester resin wastewater contaminated by 1,4-dioxane and heavy metals via up-flow anaerobic self-separation gases reactor

    International Nuclear Information System (INIS)

    Mahmoud, Mohamed; Elreedy, Ahmed; Pascal, Peu; Sophie, Le Roux; Tawfik, Ahmed

    2017-01-01

    Highlights: • Bio-hythane production from polyester wastewater via UASG reactor was assessed. • Impacts of influent contamination by 1,4-dioxane and heavy metals were discussed. • Maximum volumetric H 2 and CH 4 productions of 0.12 and 1.06 L/L/d were achieved. • Significant drop in CH 4 production was resulted at OLR up to 1.07 ± 0.06 gCOD/L/d. • Bioenergy recovery through UASG economically achieved a net profit of 10,231 $/y. - Abstract: A long-term evaluation of hythane generation from unsaturated polyester resin wastewater contaminated by 1,4-dioxane and heavy metals was investigated in a continuous up-flow anaerobic self- separation gases (UASG) reactor inoculated with mixed culture. The reactor was operated at constant hydraulic retention time (HRT) of 96 h and different organic loading rates (OLRs) of 0.31 ± 0.04, 0.71 ± 0.08 and 1.07 ± 0.06 gCOD/L/d. Available data showed that volumetric hythane production rate was substantially increased from 0.093 ± 0.021 to 0.245 ± 0.016 L/L/d at increasing OLR from 0.31 ± 0.04 to 0.71 ± 0.08 gCOD/L/d. However, at OLR exceeding 1.07 ± 0.06 gCOD/L/d, it was dropped to 0.114 ± 0.016 L/L/d. The reactor achieved 1,4-dioxane removal efficiencies of 51.8 ± 2.8, 35.9 ± 1.6 and 26.3 ± 1.6% at initial 1,4-dioxane concentrations of 1.14 ± 0.28, 1.97 ± 0.41 and 4.21 ± 0.30 mg/L, respectively. Moreover, the effect and potential removal of the contaminated by heavy metals (i.e., Cu 2+ , Mn 2+ , Cr 3+ , Fe 3+ and Ni 2+ ) were highlighted. Kinetic modelling and microbial community dynamics were studied, according to each OLR, to carefully describe the UASG performance. The economic analysis showed a stable operation for the anaerobic digestion of unsaturated polyester resin wastewater using UASG, and the maximum net profit was achieved at OLR of 0.71 ± 0.08 gCOD/L/d.

  8. Identification of 1,3-dioxane and 1,3-dioxolanes as compounds causing tastes and odors in drinking water supplies; Identificacion de 1,3-dioxanos y 1,3-dioxolanos como compuestos causantes de gustos y olores en aguas destinadas a abastecimiento publico

    Energy Technology Data Exchange (ETDEWEB)

    Ventura, F.; Romero, J.; Caixach, J.; Rivera, J.; Gode, L. X.; Ninerola, J. M.; Costa, C.

    1998-12-31

    A study of organic compounds imparting odor problems in river and groundwater has been conducted. The Tordera aquifer was polluted by 2-alkyl-5,5-dimethyl-1,3-dioxanes and 2-alkyl-4-methyl-1,3-dioxolanes coming from a resin manufacturing plant in the upper course of the river. This study shows the evolution of the groundwater quality after two years of the incidents and how the concentration levels of dioxanes and dioxolanes were lowered after a better treatment of wastewaters by the company. Additional improvements of the analytical methodology are also shown. (Author) 18 refs.

  9. UV Photolysis of Chloramine and Persulfate for 1,4-Dioxane Removal in Reverse-Osmosis Permeate for Potable Water Reuse.

    Science.gov (United States)

    Li, Wei; Patton, Samuel; Gleason, Jamie M; Mezyk, Stephen P; Ishida, Kenneth P; Liu, Haizhou

    2018-06-05

    A sequential combination of membrane treatment and UV-based advanced oxidation processes (UV/AOP) has become the industry standard for potable water reuse. Chloramines are used as membrane antifouling agents and therefore carried over into the UV/AOP. In addition, persulfate (S 2 O 8 2- ) is an emerging oxidant that can be added into a UV/AOP, thus creating radicals generated from both chloramines and persulfate for water treatment. This study investigated the simultaneous photolysis of S 2 O 8 2- and monochloramine (NH 2 Cl) on the removal of 1,4-dioxane (1,4-D) for potable-water reuse. The dual oxidant effects of NH 2 Cl and S 2 O 8 2- on 1,4-D degradation were examined at various levels of oxidant dosage, chloride, and solution pH. Results showed that a NH 2 Cl-to-S 2 O 8 2- molar ratio of 0.1 was optimal, beyond which the scavenging by NH 2 Cl of HO • , SO 4 •- , and Cl 2 •- radicals decreased the 1,4-D degradation rate. At the optimal ratio, the degradation rate of 1,4-D increased linearly with the total oxidant dose up to 6 mM. The combined photolysis of NH 2 Cl and S 2 O 8 2- was sensitive to the solution pH due to a disproportionation of NH 2 Cl at pH lower than 6 into less-photoreactive dichloramine (NHCl 2 ) and radical scavenging by NH 4 + . The presence of chloride transformed HO • and SO 4 •- to Cl 2 •- that is less-reactive with 1,4-D, while the presence of dissolved O 2 promoted gaseous nitrogen production. Results from this study suggest that the presence of chloramines can be beneficial to persulfate photolysis in the removal of 1,4-D; however, the treatment efficiency depends on a careful control of an optimal NH 2 Cl dosage and a minimal chloride residue.

  10. Characterization of Meldrum's acid derivative 5-(5-Ethyl-1,3,4-thiadiazol-2-ylamino)methylene-2,2-dimethyl-1,3-dioxane-4,6-dione by Raman and FT-IR spectroscopy and DFT calculations

    Science.gov (United States)

    de Toledo, T. A.; da Silva, L. E.; Teixeira, A. M. R.; Freire, P. T. C.; Pizani, P. S.

    2015-07-01

    In this study, the structural and vibrational properties of Meldrum's acid derivative 5-(5-Ethyl-1,3,4-thiadiazol-2-ylamino)methylene-2,2-dimethyl-1,3-dioxane-4,6-dione, C11H13N3O4S were studied combining experimental techniques such as Raman and FT-IR spectroscopy and density functional theory (DFT) calculations. The Raman and FT-IR spectra were recorded at room conditions in the regions from 80 to 3400 cm-1 and 400 to 4000 cm-1, respectively. Vibrational wavenumbers were predicted using DFT calculations with the hybrid functional B3LYP and basis set 6-31G(d,p). A comparison between experimental and theoretical data is provided for the Raman and FT-IR spectra. The descriptions of the normal modes were carried by means of potential energy distribution (PED).

  11. Synthesis, structure characterization and biological studies on a new aromatic hydrazone, 5-(2-(1,5-dimethyl-3-oxo-2-phenyl-2,3-dihydro-1H-pyrazol-4-yl)hydrazono)-2,2-dimethyl-1,3-dioxane-4,6-dione, and its transition metal complexes

    Science.gov (United States)

    Kumar, Shubha S.; Biju, S.; Sadasivan, V.

    2018-03-01

    A new aromatic hydrazone 5-(2-(1,5-dimethyl-3-oxo-2-phenyl-2,3-dihydro-1H-pyrazol-4-yl)hydrazono)-2,2-dimethyl-1,3-dioxane-4,6-dione has been synthesized by Japp-Klingemann reaction from diazotized 4-aminoantipyrine and Meldrum's acid. A few 3d-metal ion complexes of this hydrazone were synthesized. The compound and its complexes were characterized by UV-Visible, 1H NMR, ESR, Mass spectral, molar conductance and magnetic susceptibility measurements. The compound was found to exist in hydrazone form in solid state and solution from SXRD and 1H NMR study. The influence of pH on the molecule was studied and found that it shows azo/enol-hydrazone tautomerism in solution. This molecule act as a univalent tridentate ligand and the complexes were assigned to have a 1:2 stoichiometry (M:L). The antioxidant properties of the compounds were explored by DPPH assay and found that the ligand possesses better free radical scavenging effect than the complexes. Antimicrobial activities of these compounds were investigated and were found to be active.

  12. Apparent molar volumes and apparent molar heat capacities of aqueous tetrahydrofuran, dimethyl sulfoxide, 1,4-dioxane, and 1,2-dimethoxyethane at temperatures from 278.15 K to 393.15 K and at the pressure 0.35 MPa

    International Nuclear Information System (INIS)

    Swenson, D.M.; Blodgett, M.B.; Ziemer, S.P.; Woolley, E.M.

    2008-01-01

    We determined apparent molar volumes V φ at 278.15 ≤ (T/K) ≤ 368.15 and apparent molar heat capacities C p,φ at 278.15 ≤ (T/K) ≤ 393.15 at p = 0.35 MPa for aqueous solutions of tetrahydrofuran at m from (0.016 to 2.5) mol . kg -1 , dimethyl sulfoxide at m from (0.02 to 3.0) mol . kg -1 , 1,4-dioxane at m from (0.015 to 2.0) mol . kg -1 , and 1,2-dimethoxyethane at m from (0.01 to 2.0) mol . kg -1 . Values of V φ were determined from densities measured with a vibrating-tube densimeter, and values of C p,φ were determined with a twin fixed-cell, differential, temperature-scanning calorimeter. Empirical functions of m and T for each compound were fitted to our V φ and C p,φ results

  13. Thermodynamics of the amalgam cells {l_brace}Cs-amalgam|CsX (m)|AgX|Ag{r_brace} (X=Cl, Br, I) and primary medium effects in (methanol+water) (acetonitrile+water), and (1,4-dioxane+water) solvent mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Falciola, Luigi [Department of Physical Chemistry and Electrochemistry, University of Milan, Via Golgi 19, I-20133 Milan (Italy)]. E-mail: luigi.falciola@unimi.it; Longoni, Giorgio [Department of Physical Chemistry and Electrochemistry, University of Milan, Via Golgi 19, I-20133 Milan (Italy); Mussini, Patrizia R. [Department of Physical Chemistry and Electrochemistry, University of Milan, Via Golgi 19, I-20133 Milan (Italy)]. E-mail: patrizia.mussini@unimi.it; Mussini, Torquato [Department of Physical Chemistry and Electrochemistry, University of Milan, Via Golgi 19, I-20133 Milan (Italy)]. E-mail: torquato.mussini@unimi.it

    2006-06-15

    The potential difference E of the amalgam cell {l_brace}Cs{sub x}Hg{sub 1-x}|CsX (m)|AgX|Ag{r_brace} (X=Cl, Br, I) has been measured as a function of the mole fraction x{sub Cs} of Cs metal in amalgams and of the molality m of CsX in (methanol+water) (acetonitrile+water), and (1,4-dioxane+water) solvent mixtures containing up to 0.75 mass fraction of the organic component, at the temperature 298.15K. The respective standard molal potential differences E{sub m}{sup o} have been determined together with the relevant activity coefficients {gamma}{sub +}/- as functions of the CsX molality. The found E{sub m}{sup o} values show a parabolic decrease with increasing proportion of the organic component in the solvent mixture. Analysis of the relevant primary medium effects upon CsX shows that the CsX transfer from the standard state in water to the standard state in the (aqueous+organic) mixture is always unfavoured, and the acetonitrile is the least unfavoured co-solvent studied. Analysis of the primary medium effect upon CsI in terms of Feakins and French's theory leads to a primary hydration number close to zero, which is consistent with the results of supplementary EXAFS experiments on Cs{sup +} and I{sup -} in (acetonitrile+water) solvent mixtures.

  14. Oligonucleotides with 1,4-dioxane-based nucleotide monomers

    DEFF Research Database (Denmark)

    Madsen, Andreas S; Wengel, Jesper

    2012-01-01

    An epimeric mixture of H-phosphonates 5R and 5S has been synthesized in three steps from known secouridine 1. Separation of the epimers has been accomplished by RP-HPLC, allowing full characterization and incorporation of monomers X and Y into 9-mer oligonucleotides using H-phosphonates building...... blocks 5R and 5S, respectively. A single incorporation of either monomer X or monomer Y in the central position of a DNA 9-mer results in decreased thermal affinity toward both DNA and RNA complements (ΔT(m) = -3.5 °C/-3.5 °C for monomer X and ΔT(m) = -11.0 °C/-6.5 °C for monomer Y). CD measurements do...

  15. New chiral liquid crystal with unconventional dioxane terminal unit

    Czech Academy of Sciences Publication Activity Database

    Perkowski, P.; Bubnov, Alexej; Mrukiewicz, M.; Pociecha, D.; Piecek, W.; Hamplová, Věra; Kašpar, Miroslav

    2014-01-01

    Roč. 87, 10-11 (2014), s. 1024-1037 ISSN 0141-1594 R&D Projects: GA MŠk 7AMB13PL041; GA MŠk(CZ) LD14007; GA MŠk(CZ) 7AMB14PL035; GA ČR GA13-14133S Grant - others:AV ČR(CZ) M100101211; AVČR(CZ) M100101204; EU - ICT (XE) COST Action IC1208 Institutional support: RVO:68378271 Keywords : chiral liquid crysta * pentaglyform unit * structural properties * smectic phase * hexagonal ordering * self-assembling Subject RIV: JJ - Other Materials Impact factor: 0.954, year: 2014

  16. In Situ Treatment and Management Strategies for 1,4-Dioxane-Contaminated Groundwater

    Science.gov (United States)

    2017-05-05

    and Figure 71). The surviving microorganisms that were tolerant of catalysis treatment were able to thrive in the post-catalysis biodegradation phase... microorganisms thrived during the biodegradation process. This was consistent with oxidation process that biodiversity was inhibited by the chemical reaction...During the biodegradation phase, microorganisms were able to grow in relatively suitable conditions and thus more species thrived after biodegradation

  17. Investigation of REE perchlorates complexing with benzimidazole in aqua-dioxane media

    International Nuclear Information System (INIS)

    Akhrimenko, Z.M.; Panyushkin, V.T.; Ishbulatova, S.K.

    1992-01-01

    Stability constant (K 1 ) of complexes of rare earth perchlorates with benzimidazole were determined by the method of pH-metric titration. Nonmonotonous change in lgK 1 with rare earth ordinal number increase was revealed

  18. Liquid Crystalline Polymers Containing Heterocycloalkane Mesogens. 2. Side-Chain Liquid Crystalline Polysiloxanes Containing 2,5-Disubstituted-1,3-Dioxane Mesogens.

    Science.gov (United States)

    1986-10-01

    groups. In the previous paper from this series (47) we presented the synthesis and characterization of several polyacrylates and polymethacrylates based...dilute sulfuric acid (14.5 ml of concentrated sulfuric acid in 250 ml of water). An almost colorless oil separated from the aqueous phase. The two...of 10% sulfuric acid and extracted with chloroform. The organic phase was washed with 2% aqueous sodium bicarbonate, water and dried over anhydrous

  19. Investigation of REE perchlorates complexing with benzimidazole in aqua-dioxane media. Issledovanie kompleksoobrazovaniya perkhloratov RZEh s benzimidazolom v vodno-dioksanovoj srede

    Energy Technology Data Exchange (ETDEWEB)

    Akhrimenko, Z M; Panyushkin, V T; Ishbulatova, S K [Kubanskij Gosudarstvennyj Univ., Krasnodar (Russian Federation)

    1992-01-01

    Stability constant (K[sub 1]) of complexes of rare earth perchlorates with benzimidazole were determined by the method of pH-metric titration. Nonmonotonous change in lgK[sub 1] with rare earth ordinal number increase was revealed.

  20. Interpolymer complexes based on the core/shell micelles. Interaction of polystyrene-block-poly(methacrylic acid) micelles with linear poly(2-vinylpyridine) in 1,4-dioxane water mixtures and in aqueous media

    Czech Academy of Sciences Publication Activity Database

    Matějíček, P.; Uchman, M.; Lokajová, J.; Štěpánek, M.; Procházka, K.; Špírková, Milena

    2007-01-01

    Roč. 111, č. 29 (2007), s. 8394-8401 ISSN 1520-6106. [International Symposium on Polyelectrolytes /6./. Dresden, 04.09.2006-08.09.2006] R&D Projects: GA ČR GA203/04/0490; GA AV ČR IAA400500505 Institutional research plan: CEZ:AV0Z40500505 Keywords : polystyrene-block-poly(methacrylic acid) * poly(2-vinylpyridine) * core/shell micelles * light scattering * atomic force microscopy Subject RIV: CD - Macromolecular Chemistry Impact factor: 4.086, year: 2007

  1. Stability of rare earth complexes with 2-(o-hydroxyphenyl)benzimidazole in aqueous-dioxane medium. Ustojchivost' kompleksnykh soedinenij RZEh s 2-(o-oksifenil)benzimidazolom v vodno-dioksanovoj srede

    Energy Technology Data Exchange (ETDEWEB)

    Akhrimenko, Z M; Panyushkin, V T; Fedorova, M V [Kubanskij Gosudarstvennyj Univ., Krasnodar (USSR)

    1990-01-01

    Method of potentiometric titration was used to determine protonation constants of 2-(-hydroxyphenyl)benzimidazole (pK{sub 1}=4.5; pK{sub 2}=11.30) and stability constants of Pr,Nd,Sm,Eu,Tb,Dy complexes with this ligand. Nonmonotonous change of lgK{sub 1} with increase of ordinal number of rare earth element was revealed.

  2. STABILITY OF BINARY COMPLEXES OF L-ASPARTIC ACID IN ...

    African Journals Online (AJOL)

    Preferred Customer

    KEY WORDS: Binary complexes, Stability constants, Aspartic acid, Speciation, Dioxan. INTRODUCTION. 1,4-Dioxan (Dox) is ... It is miscible with water, oils, and most organic solvents, including aromatic .... of mineral acid in metal ion and ligand solutions was determined using the Gran plot method. [28, 29]. To assess the ...

  3. Preparation of butadiene D{sub 6} -1-1-2-3-4-4; Preparation du butadiene D{sub 6} -1-1-2-3-4-4

    Energy Technology Data Exchange (ETDEWEB)

    Pichat, L; Chatelain, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    A description of the preparation of butadiene D{sub 6} by dehalogenation of perchlorobutadiene by zinc and heavy water in dioxane. (author) [French] Description de la preparation du butadiene D{sub 6} par reduction deshalogenante du perchlorobutadiene par le zinc et l'eau lourde dans le dioxane. (auteur)

  4. Geohydrology, water quality, and simulation of ground-water flow in the vicinity of a former waste-oil refinery near Westville, Indiana, 1997-2000

    Science.gov (United States)

    Duwelius, Richard F.; Yeskis, Douglas J.; Wilson, John T.; Robinson, Bret A.

    2002-01-01

    Geohydrologic and water-quality data collected during 1997 through 2000 in the vicinity of a former waste-oil refinery near Westville, Indiana, define a plume of 1,4-dioxane in ground water that extends to the southwest approximately 0.8 miles from the refinery site. Concentrations of 1,4-dioxane in the plume ranged from 3 to 31,000 micrograms per liter. Ground water containing 1,4-dioxane is discharged to Crumpacker Ditch, approximately one-half mile west of the refinery site. Concentrations of 1,4-dioxane detected in surface water ranged from 8 to 140 micrograms per liter; 1,4-dioxane also is transported in ground water beneath the ditch.

  5. Biodegradation of lignin by Shiitake Lentinus edodes (berk. ) sing

    Energy Technology Data Exchange (ETDEWEB)

    Oki, T.; Watanabe, H.; Ishikawa, H.

    1981-01-01

    Each strain of L. edodes destroyed all of the structural components of wood (Fagus crenata) at almost the same rate during the loss of approximately 30% of the total weight of wood. The activities of the extracellular enzymes, i.e. peroxidase, laccase, and polyphenol oxidase, in the wood powder and lignin-containing cultures increased during the early period of mycelial growth, and then declined rapidly, while the activity of Beta-glucosidase increased gradually throughout the growth period. Functional group analysis, nitrobenzene oxidation, and spectroscopic characterization showed that dioxane lignin from F. crenata degraded by L. edodes or in crude enzyme solution isolated from wood-containing culture had a higher content of carboxyl groups than the sound dioxane lignin, whereas the content of methoxyl group was lower in the degraded dioxane lignin than in sound dioxane lignin. The building units of dioxane lignin, which yield aromatic aldehydes on nitrobenzene oxidation, were attacked preferentially by L. edodes under the above conditions.

  6. M(4-PridinkarboksialdehidNi(CN4.nG Hofmann Tipi Konak-Konuk Bileşiklerinin Kırmızıaltı Spektroskopik Özelliklerinin İncelenmesi (M = Ni, Cd ve G = 1,4-Dioksan

    Directory of Open Access Journals (Sweden)

    Zeki KARTAL

    2014-12-01

    M(4-PyridinecarboxaldehydeNi(CN4.nG Hofmann Type Clathrates (M = Ni, Cd and G = 1,4-Dioxane Abstract: In this study, clathrate of 4-pyridinecarboxaldehyde tetracyanonickel-dioxane, given by the formula M(4-PyridinecarboxaldehydeNi(CN4 nG (m = Ni, Cd and G = 1,4-dioxane, is obtained for the first time through chemical methods. The FT-IR spectroscopic data in the region of (3000–400 cm-1 was recorded and the IR vibrational modes frequencies were given and explained in detail. The spectral analyzes results of the newly synthesized clathrate of 4-pyridinecarboxaldehyde tetracyanonickel- dioxane suggests that these clathrates are new examples of the Hofmann-type dioxane clathrates. In our study, the Hofmann-type dioxane clathrates formed by bounding electrons of nitrogen-donor atom of pyridine ring and electrons of oxygen-donor atom of aldehyde group (-CH=O of 4-pyridinecarboxaldehyde ligand molecule to transition metal atoms consist of the corrugated |M–Ni(CN4|ï‚¥ polymeric layers which are held in parallel through the chain of (–M–4PCA–M–. Key words: Infrared Spectroscopy, Hofmann Types Clathrates, Tetracyanonickelate, 4-pyridinecarboxaldehyde, 1,4-dioxane

  7. Pramana – Journal of Physics | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    propanediol, 1,4-dioxane and their mixtures have been studied using time domain reflectometry (TDR). The excess permittivity, excess inverse relaxation time and Kirkwood correlation factor have also been determined at various concentrations of ...

  8. Author Index 991..998

    Indian Academy of Sciences (India)

    dioxanes using polyaniline supported acid as reusable catalyst. 623. Bose P ... silica sulfuric acid. 453. Ghosh A .... /KI or cerium ammonium .... sulfate micelles. 909. Pednekar S .... Computational study on decomposition kinetics of. CH3CFClO ...

  9. Radical fragmentation of six-membered oxygen-containing heterocycles

    International Nuclear Information System (INIS)

    Petryaev, E.P.; Kosobutskij, V.S.; Shadyro, O.I.

    1982-01-01

    Using chromatography, the composition and radiation-chemical yields of final products of desctruction of six-member saturated oxygen-containing heterocycles (the effect of #betta#-radiation on aqueous solutions of tetrahydropyran, 1,3-dioxane, 2,2 dimethyl-1,3 dioxane, 1,4-dioxane, paraldehyde) have been determined. It is established that the identified products are formed at the expense of decomposition of primary radicals of the initial compounds and point to the realization of the following fragmentation ways: 1) #betta#-scattering, 2) #betta#-scattering with a subsequent 1,5 migration of an H atom, 3) simultaneous rupture of two vicinal, relative to the radical center, bonds. A formation mechanism of the substances desctruction products is suggested. Material balance of the product yields of 1,3-dioxane radical synchronous decomposition is presented

  10. Cryochemistry: freezing effect on peptide coupling in different organic solutions.

    Science.gov (United States)

    Vajda, T; Szókán, G; Hollósi, M

    1998-06-01

    The freezing effect on peptide coupling in organic solutions of different polarity has been investigated and compared with the results obtained in liquid phase. The model reaction of DCC-activated coupling of Boc-Ala-Phe-OH with H-Ala-OBu(t) has been carried out in dioxane, dimethylsulfoxide and formamide, as well as in mixtures (90%/10%, v/v) of dioxane with acetonitrile, dimethylformamide, dimethylsulfoxide and formamide. The reactions have been traced and evaluated by RP-HPLC analysis. Freezing the reaction mixture resulted in all cases in a significant suppression of the N-dipeptidylurea side-product formation together with a slight decrease of tripeptide epimerization. The coupling yields and the side effects depended on the solvent, with the dioxane and dioxane/acetonitrile mixture produced the best results. The role of freezing and solvent in the improved results is discussed.

  11. Evaluation of antibacterial activity and phytochemical analysis of ...

    African Journals Online (AJOL)

    defatted plant material as well as the defatted plant material was then individually extracted in different solvents with increasing polarity viz. 1,4-dioxan, acetone, methanol, dimethylformamide (DMF) and distilled water respectively. The extractive ...

  12. Administration of Chemistry, Research Department

    African Journals Online (AJOL)

    ), kobs varies non linearly with the soivent composition, passing through a minimum in the region of equimolar portions of the two components. This is in contradiction to the behaviour in ethanol - dioxane and ethanol. - propan-2-ol mixtures, ...

  13. Effect of strong electrolytes on edible oils part II: vViscosity of maize ...

    African Journals Online (AJOL)

    DR. MIKE HORSFALL

    dioxane in the presence of HCl, NaOH and NaCl at different temperatures. 1A. RASHEED KHAN; 2SHAMA, REHANA SAEED; 2*FAHIM UDDIN. 1Department of Chemistry, Federal Urdu University of Arts, Science & Technology,. Karachi Pakistan.

  14. Dihydroxylation of 4-substituted 1,2-dioxines

    DEFF Research Database (Denmark)

    Robinson, Tony V; Pedersen, Daniel Sejer; Taylor, Dennis K

    2009-01-01

    The synthesis of 2-C-branched erythritol derivatives, including the plant sugar (+/-)-2-C-methylerythritol 2, was achieved through a dihydroxylation/reduction sequence on a series of 4-substituted 1,2-dioxines 3. The asymmetric dihydroxylation of 1,2-dioxines was examined, providing access...... to optically enriched dihydroxy 1,2-dioxanes 4. The synthesized 1,2-dioxanes were converted to other erythro sugar analogues and tetrahydrofurans through controlled cleavage of the endoperoxide linkage....

  15. The effect of processing and composition on the properties of polylactide–multiwall carbon nanotube composites prepared by solvent casting

    International Nuclear Information System (INIS)

    Rizvi, Reza; Naguib, Hani; Kim, Jae-Kyung

    2010-01-01

    This study investigates the effects of processing solvent and filler concentration on the thermal, electrical and mechanical properties of polylactide (PLA)–multiwall carbon nanotube (MWNT) composites. PLA–MWNT composites were prepared by a solvent casting method using two different solvents, chloroform and 1,4-dioxane, in compositions of 0, 0.5, 2 and 5 wt% MWNTs. The dispersion of the MWNTs in PLA was examined using a scanning electron microscope and was found to be improved when 1,4-dioxane was used as the solvent as compared with when chloroform was used. Owing to their better MWNT dispersion, composites prepared using 1,4-dioxane displayed a greater dependence on the MWNT concentration of the thermal, electrical and mechanical properties. Composites prepared using 1,4-dioxane had a greater effect on PLA's decomposition temperature and displayed faster crystallization kinetics than those prepared using chloroform. Not only was the conductivity of 1,4-dioxane prepared composites greater than that of chloroform prepared composites, but also the filler percolation point was observed to be reduced as well (less than 0.5 wt% MWNTs). At 5 wt% MWNT composition, a 31% increase in Young's modulus was observed in 1,4-dioxane prepared composites while a 14% improvement was observed in chloroform prepared composites, as compared with neat PLA. On the basis of the results, it is believed that the chemical interaction between the carboxylated MWNTs and 1,4-dioxane allows for a better dispersion of the MWNTs in PLA

  16. A comparative study of 19-iodo cholesterol-125I 3-acetate and Na 125I in liquid scintillation measurements; Estudio comparativo del acetato de 19-iodocolesterol- -125I con Nal25I en medidas por centelleo liquido

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Barquero, L.; Grau Malonda, A.; Los Arcos Merino, J. M.; Grau Carles, A.

    1994-07-01

    A comparative study of performance of 19-iodo cholesterol {sup 1}25I 3-acetate and sodium iodide samples labeled with 125I is presented for liquid scintillation counting measurements. Quench effect, count rate stability and spectral evolution of samples have been followed for several weeks in Toluene, Hisafe II, Instagel, Dioxane-naphthalene and Toluene-alcohol scintillators. Organic samples have negligible quench effect in the interval of I concentration of 0-90 {mu}g and inorganic samples only show a very small variation, lower than 12%, for Dioxane-naphthalene, in the same range of concentration. Satisfactory stability is obtained in general for both, organic and inorganic samples, but small counting losses, 0.03% for 19-iodocholesterol 1 I 3-acetate samples in Tolue ne-alcohol and 0 .04% for Na 125I samples in Dioxane-naphthalene and Toluene-alcohol, have been reported. (Author) 8 refs.

  17. A comparative study of 19-iodocholesterol-''125I 3-acetate and Na''125I in liquid scintillation measurements

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Grau Malonda, A.; Los Arcos Merino, J.M.; Grau Carles, A.

    1994-01-01

    A comparative study of performance of 19-iodocholesterol-''125I 3-acetate and sodium iodine samples labelled with ''125 I is presented for liquid scintillation counting measurements. Quench effect, count rate stability and spectral evolution of samples have been followed for several weeks in Toluene, Hisafe II, Instagel, Dioxane-naphthalene and Toluene-alcohol scintillators. Organic samples have negligible quench effect in the interval of I''-concentration of 0-90 ug and inorganic samples only show a very small variation, lower than 12%, for Dioxane-naphthalene, in the same range of concentration. Satisfactory stability is obtained in general for both, organic and inorganic samples, but small counting losses, 0.03% for 19-iodocholesterol-''125I 3-acetate samples in Toluene-alcohol and 0.04% for Na''125I samples in Dioxane-naphthalene and Toluene-alcohol, have been reported. (Author) 8 refs

  18. A comparative study of 19-iodo cholesterol-125I 3-acetate and Na 125I in liquid scintillation measurements

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Grau Malonda, A.; Los Arcos Merino, J. M.; Grau Carles, A.

    1994-01-01

    A comparative study of performance of 19-iodo cholesterol 1 25I 3-acetate and sodium iodide samples labeled with 125I is presented for liquid scintillation counting measurements. Quench effect, count rate stability and spectral evolution of samples have been followed for several weeks in Toluene, Hisafe II, Instagel, Dioxane-naphthalene and Toluene-alcohol scintillators. Organic samples have negligible quench effect in the interval of I concentration of 0-90 μg and inorganic samples only show a very small variation, lower than 12%, for Dioxane-naphthalene, in the same range of concentration. Satisfactory stability is obtained in general for both, organic and inorganic samples, but small counting losses, 0.03% for 19-iodocholesterol 1 I 3-acetate samples in Tolue ne-alcohol and 0 .04% for Na 125I samples in Dioxane-naphthalene and Toluene-alcohol, have been reported. (Author) 8 refs

  19. Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare γ-Valerolactone

    Directory of Open Access Journals (Sweden)

    Jie Fu

    2015-12-01

    Full Text Available Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3 with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA to prepare γ-valerolactone (GVL. The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.

  20. From Symmetric Glycerol Derivatives to Dissymmetric Chlorohydrins

    Directory of Open Access Journals (Sweden)

    Gemma Villorbina

    2011-03-01

    Full Text Available The anticipated worldwide increase in biodiesel production will result in an accumulation of glycerol for which there are insufficient conventional uses. The surplus of this by-product has increased rapidly during the last decade, prompting a search for new glycerol applications. We describe here the synthesis of dissymmetric chlorohydrin esters from symmetric 1,3-dichloro-2-propyl esters obtained from glycerol. We studied the influence of two solvents: 1,4-dioxane and 1-butanol and two bases: sodium carbonate and 1-butylimidazole, on the synthesis of dissymmetric chlorohydrin esters. In addition, we studied the influence of other bases (potassium and lithium carbonates in the reaction using 1,4-dioxane as the solvent. The highest yield was obtained using 1,4-dioxane and sodium carbonate.

  1. Mechanistic Insights into Solvent and Ligand Dependency in Cu(I)-Catalyzed Allylic Alkylation with gem-Diborylalkanes.

    Science.gov (United States)

    Zhang, Qi; Wang, Bing; Liu, Jia-Qin; Fu, Yao; Wu, Yu-Cheng

    2018-01-19

    The recent Cu-catalyzed allylic substitution reaction between gem-diboryalkane and allyl electrophiles shows intriguing solvent and ligand-controlled regioselectivity. The α-alkylation product was obtained in DMF solvent, while γ-alkylation product was obtained in dioxane solvent and the dioxane and NHC ligand situation. In the present study, density functional theory calculations have been used to investigate the reaction mechanism and origin of the regioselectivity. For both dioxane and DMF, γ-alkylation undergoes successive oxidative addition (CH 2 Bpin trans to leaving group) and direct Cγ-C reductive elimination. The α-alkylation is found to undergo oxidative addition (CH 2 Bpin trans to leaving group), isomerization, and Cα-C reductive elimination rather than the previously proposed oxidative addition (-CH 2 Bpin cis to the leaving group) and Cα-C reductive elimination. The γ-alkylation and α-alkylation is, respectively, favorable for dioxane and DMF solvent, which is consistent with the γ- and α-selectivity in experiment. The solvent interferes the isomerization step, thereby affects the relative facility of the α- and γ-alkylation. Further investigation shows that η 1 -intermediate formation promoted by solvent is the rate-determining step of the isomerization. The stronger electron-donating ability of DMF than dioxane facilitates the η 1 -intermediate formation and finally results in the easier isomerization in DMF. For dioxane and NHC situation, in the presence of neutral NHC ligand, the -PO 4 Et 2 group tightly coordinates with the Cu center after the oxidative addition, preventing the isomerization process. The regioselectivity is determined by the relative facility of the oxidative addition step. Therefore, the favorable oxidative addition (in which -CH 2 Bpin trans to the leaving group) results in the facility of γ-alkylation.

  2. Self-assembly in casting solutions of block copolymer membranes

    KAUST Repository

    Marques, Debora S.; Vainio, Ulla; Moreno Chaparro, Nicolas; Calo, Victor M.; Bezahd, Ali Reza; Pitera, Jed W.; Peinemann, Klaus; Nunes, Suzana Pereira

    2013-01-01

    Membranes with exceptional pore regularity and high porosity were obtained from block copolymer solutions. We demonstrate by small-angle X-ray scattering that the order which gives rise to the pore morphology is already incipient in the casting solution. Hexagonal order was confirmed in PS-b-P4VP 175k-b-65k solutions in DMF/THF/dioxane with concentrations as high as 24 wt%, while lamellar structures were obtained in more concentrated solutions in DMF or DMF/dioxane. The change in order has been understood with the support of dissipative particle dynamic modeling. © 2013 The Royal Society of Chemistry.

  3. An Organic Puzzle Using Meldrum's Acid

    Science.gov (United States)

    Crouch, R. David; Holden, Michael S.

    2002-04-01

    Meldrum's acid or 2,2-dimethyl-1,3-dioxane-4,6-dione undergoes a Knoevenagel condensation with formaldehyde to form an active Michael acceptor for a second molecule of Meldrum's acid. The structure of the resulting product is determined by correlation of the products of possible reactions of Meldrum's acid and formaldehyde with the NMR spectrum of the product.

  4. Journal of Chemical Sciences | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Chemical Sciences. Ruli Borah. Articles written in Journal of Chemical Sciences. Volume 123 Issue 5 September 2011 pp 623-630. Investigation of Prins reaction for the synthesis of 2, 4- disubstituted tetrahydropyran derivatives and 1, 3-dioxanes using polyaniline supported acid as reusable ...

  5. Nitrous Acid as an Oxidant in Acidic Media

    Science.gov (United States)

    1979-09-25

    current work is the account of Ogsts and Sawski3 who studied the oxidation of benzyl ethers at 90C in acidic, aqueous dioxane. They found an increase in...and G. Tobin, Chem. Com., 180 (1978); (b) J. Hoggett , R. Moodie, and K. Schofield, Chem. Comm., 605 (1969). 15. (a) B. Challis and A. Lawson. J. Chem

  6. Untitled

    African Journals Online (AJOL)

    Proceeds through a pentacovalent phosphorus intermediate (9) (scheme 1), except ... The base-nucleophiles may be expected to become highly reactive in non-polar dioxane owing to the lack of hydrogen bond stabilization (11). Methoxide ion, ... metal (BDH) and methanol, the concentrations were determined by titration.

  7. Development of wet-dry reversible reverse osmosis membrane with high performance from cellulose acetate and cellulose triactate blend

    NARCIS (Netherlands)

    Vasarhelyi, K.; Ronner, J.A.; Mulder, M.H.V.; Smolders, C.A.

    1987-01-01

    Wet-dry reversible membrane were prepared bt a two-step coagulation procedure. A cast film containing a blend of cellulose triacetate as polymers, dioxane and acetone as solvents and maleic acid and methanol as additives was immersed consecutively in two aqueous coagulation baths, the first bath

  8. 40 CFR Table 3 to Subpart Ggg of... - Soluble HAP

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Soluble HAP 3 Table 3 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... HAP Compound 1,1-Dimethylhydrazine. 1,4-Dioxane. Acetonitrile. Acetophenone. Diethyl sulfate. Dimethyl...

  9. Preparation of radioactive labelled compounds. Pt. 2. 82Br labelled organic bromine compounds by isotopic exchange

    International Nuclear Information System (INIS)

    Otto, R.

    1988-05-01

    Studies on isotopic exchange between organic bromine compounds and 82 Br labelled dioxane dibromide in the presence of AlCl 3 are described. The results obtained enable to develop a simple and quick preparation method for the labelling with 82 Br [fr

  10. Formation of binary complexes of Co(II), Ni(II) and Cu(II) with L ...

    African Journals Online (AJOL)

    The trend in the variation of stability constants with change in the mole fraction of the medium was explained based on electrostatic and non-electrostatic forces. Distribution of the species with pH at different compositions of dioxan-water mixtures was also presented. KEY WORDS: Binary species, Stability constants, Metal, ...

  11. FY 2009 SERDP Annual Report

    Science.gov (United States)

    2010-02-01

    Response Program NDMA N-nitrosodimethylamine NEPA National Environmental Policy Act NESHAP National Emission Standards for Hazardous Air Pollutants...emerging contaminant. Specific emerging contaminants of interest include 1,4-dioxane, N-nitrosodimethylamine ( NDMA ) and 1,2,3- trichloropropane (TCP

  12. Pramana – Journal of Physics | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    dioxan have been estimated from the measured static relative permittivity 0 and high-frequency permittivity ∞ at different weight fractions s of polar solute at 35°C under static electric field using Debye model of polar liquid molecule.

  13. Synthesis of acyclic nucleoside 5-o-carboranyl uracil derivative ...

    African Journals Online (AJOL)

    carboranyl uracil 7 as potentially antiviral agent and a suitable candidate for BNCT is described starting from 5,5- dihydroxymethyl-1,3-dioxane 1, an intermediate 2,2,2-triacetoxymethyl ethoxymethyl acetyl 2 was synthesized and coupled with ...

  14. Solvation study of the non-specific lipid transfer protein from wheat by intermolecular NOEs with water and small organic molecules

    International Nuclear Information System (INIS)

    Liepinsh, Edvards; Sodano, Patrick; Tassin, Severine; Marion, Didier; Vovelle, Francoise; Otting, Gottfried

    1999-01-01

    Intermolecular nuclear Overhauser effects (NOEs) were measured between the protons of various small solvent or gas molecules and the non-specific lipid transfer protein (ns-LTP) from wheat. Intermolecular NOEs were observed with the hydrophobic pocket in the interior of wheat ns-LTP, which grew in intensity in the order cyclopropane (saturated solution) < methane (140 bar) < ethane (40 bar) < acetonitrile (5% in water) < cyclohexane (saturated solution) < benzene (saturated solution). No intermolecular NOEs were observed with dioxane (5% in water). The intermolecular NOEs were negative for all of the organic molecules tested. Intermolecular NOEs between wheat ns-LTP and water were weak or could not be distinguished from exchange-relayed NOEs. As illustrated by the NOEs with cyclohexane versus dioxane, the hydrophobic pocket in wheat ns-LTP preferably binds non-polar molecules. Yet, polar molecules like acetonitrile can also be accommodated. The pressure dependence of the NOEs between methane and wheat ns-LTP indicated incomplete occupancy, even at 190 bar methane pressure. In general, NOE intensities increased with the size of the ligand molecule and its vapor pressure. NMR of the vapor phase showed excellent resolution between the signals from the gas phase and those from the liquid phase. The vapor concentration of cyclohexane was fivefold higher than that of the dioxane solution, supporting the binding of cyclohexane versus uptake of dioxane

  15. Epoxidation and oxidation reactions using 1,4-butanediol ...

    Indian Academy of Sciences (India)

    Unknown

    and aryl halides to hydroxy compounds through a .... Epoxidation of olefins using 1,4-BDDMA-crosslinked polystyrene supported t- butyl hydroperoxide. Reaction. Isolated. Olefina timeb (h). Productc yield (%). Cinnamic acid. 39 ... aCinnamic acid; bcyclohexene; csubstrate to resin 1 : 2; solvent, dioxan, temperature, 70°C.

  16. Structures, chemotaxonomic significance, cytotoxic and Na(+),K(+)-ATPase inhibitory activities of new cardenolides from Asclepias curassavica.

    Science.gov (United States)

    Zhang, Rong-Rong; Tian, Hai-Yan; Tan, Ya-Fang; Chung, Tse-Yu; Sun, Xiao-Hui; Xia, Xue; Ye, Wen-Cai; Middleton, David A; Fedosova, Natalya; Esmann, Mikael; Tzen, Jason T C; Jiang, Ren-Wang

    2014-11-28

    Five new cardenolide lactates (1–5) and one new dioxane double linked cardenolide glycoside (17) along with 15 known compounds (6–16 and 18–21) were isolated from the ornamental milkweed Asclepias curassavica. Their structures were elucidated by extensive spectroscopic methods (IR, UV, MS, 1D- and 2D-NMR). The molecular structures and absolute configurations of 1–3 and 17 were further confirmed by single-crystal X-ray diffraction analysis. Simultaneous isolation of dioxane double linked cardenolide glycosides (17–21) and cardenolide lactates (1–5) provided unique chemotaxonomic markers for this genus. Compounds 1–21 were evaluated for the inhibitory activities against DU145 prostate cancer cells. The dioxane double linked cardenolide glycosides showed the most potent cytotoxic effect followed by normal cardenolides and cardenolide lactates, while the C21 steroids were non-cytotoxic. Enzymatic assay established a correlation between the cytotoxic effects in DU145 cancer cells and the Ki for the inhibition of Na(+),K(+)-ATPase. Molecular docking analysis revealed relatively strong H-bond interactions between the bottom of the binding cavity and compounds 18 or 20, and explained why the dioxane double linked cardenolide glycosides possessed higher inhibitory potency on Na(+),K(+)-ATPase than the cardenolide lactate.

  17. Facile synthesis of α-hydroxy carboxylic acids from the corresponding α-amino acids

    DEFF Research Database (Denmark)

    Stuhr-Hansen, Nicolai; Padrah, Shahrokh; Strømgaard, Kristian

    2014-01-01

    An effective and improved procedure is developed for the synthesis of α-hydroxy carboxylic acids by treatment of the corresponding protonated α-amino acid with tert-butyl nitrite in 1,4-dioxane-water. The amino moiety must be protonated and located α to a carboxylic acid function in order...

  18. ANALYSIS OF THE KINETICS OF SOLVOLYSIS OF P-NITROPHENYLSULFONYLMETHYL PERCHLORATE IN BINARY ALCOHOLIC MIXTURES IN TERMS OF THE THERMODYNAMIC PROPERTIES OF THE SOLVENT MIXTURES

    NARCIS (Netherlands)

    Wijnen, J W; Engberts, J B F N; Blandamer, Michael J

    Rate constants are reported for the solvolysis of p-nitrophenylsulfonylmethyl perchlorate in binary ethanolic and methanolic mixtures at 298.2 K. Co-solvents include hydrocarbons, chlorinated hydrocarbons and 1,4-dioxane. The kinetic data are examined in terms of the effect of decreasing mole

  19. Cu(I)/Diamine-catalyzed Aryl-alkyne Coupling Reactions

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    CuI/ethylene diamine/K2CO3/dioxane is shown to be a useful system for the cross coupling reactions of various aryl iodides and bromides with aryl and alkyl alkynes. Compared to the conventional Sonogashira reactions, the new procedure is free of palladium and phosphines.

  20. 75 FR 63827 - Integrated Risk Information System (IRIS); Request for Chemical Substance Nominations for 2011...

    Science.gov (United States)

    2010-10-18

    ... provides oral reference doses (RfDs) and inhalation reference concentrations (RfCs) for chronic noncancer...-3 4,4'-dimethyl-3-oxahexane (TAEE).. 919-94-8 1,4-dioxane (inhalation) 123-91-1 dipentyl phthalate... petroleum and are present in gasoline. Common alkylates found in gasoline for which IRIS assessments have...

  1. Polymerization of different lignins by laccase

    NARCIS (Netherlands)

    Mattinen, M.L.; Suortti, T.; Gosselink, R.J.A.; Argyropoulos, D.S.; Evtuguin, D.; Suurnäkki, A.; Jong, de E.; Tamminen, T.

    2008-01-01

    In this study the oxidative polymerization of different lignins, i.e. Flax Soda lignin, Spruce EMAL, and Eucalyptus Dioxane lignin by Trametes hirsuta laccase was compared. Initially the structures of the different lignins were compared by Fourier transform infrared spectroscopy. The reactivity of

  2. Hydrolysis of 4-Acetoxystyrene Polymers Prepared by Atom Transfer Radical Polymerization

    DEFF Research Database (Denmark)

    Chen, Xianyi; Jankova, Katja; Kops, Jørgen

    1999-01-01

    Hydrolysis of 4-acetoxystyrene polymers prepared by atom transfer radical polymerization was carried out under various reaction conditions. It was found that hydrazinolysis of 4-acetoxystyrene homopolymers, random and block copolymers with styrene in 1,4-dioxane, afforded the corresponding narrow...

  3. Effect of Calcium chloride and Cadmium chloride on the enthalpy of ...

    African Journals Online (AJOL)

    This paper presents the effect of two dissolved inorganic salts, CaCl2 and CdCl2 on the enthalpy of mixing of the binary 1,4 dioxane + water system has been investigated at 303.15 K in an isothermal displacement calorimeter with vapour space. A significantly increasing trend in the endothermic excess enthalpy values for ...

  4. Preparation of H3-labelled methyl ethers of saturated fatty acids by heterogeneous catalytic isotope exchange in solution with gaseous tritium

    International Nuclear Information System (INIS)

    Shevchenko, V.P.; Myasoedov, N.F.

    1980-01-01

    A simple method of preparing 3 H-labelled methyl ethers of saturated fatty acids in the dioxane solution using the method of isotopic heterogenous catalytic exchange with gaseous tritium, is suggested. 3 H-labelled natural fatty acids (C 12 -C 18 ) are prepared by alkaline hydrolysis [ru

  5. Dependence of protein binding capacity of dimethylamino-γ-butyric-acid (DMGABA)-immobilized porous membrane on composition of solvent used for DMGABA immobilization

    International Nuclear Information System (INIS)

    Iwanade, Akio; Umeno, Daisuke; Saito, Kyoichi; Sugo, Takanobu

    2013-01-01

    Dimethylamino-γ-butyric acid (DMGABA) as an ampholite was reacted with the epoxy group of the poly-glycidyl methacrylate chain grafted onto the pore surface of a porous hollow-fiber polyethylene membrane by radiation-induced graft polymerization. DMGABA was dissolved in a mixture of dioxane and water at various dioxane volume fractions, defined by dividing the dioxane volume by the total volume. The equilibrium binding capacity (EBC) of the DMGABA-immobilized porous hollow-fiber membrane for lysozyme was evaluated in the permeation mode. The EBC was varied from a 1/50-fold monolayer binding capacity to a 10-fold monolayer binding capacity by controlling the composition of the solvent used for DMGABA immobilization and the molar conversion of the epoxy group into the DMGABA group. - Highlights: ► A DMGABA membrane was immobilized by irradiation induced graft polymerization. ► The DMGABA was immobilized in a mixture of dioxane and water of various compositions. ► Lysozyme adsorptivity of DMGABA-immobilized membranes evaluated in the permeation mode. ► The composition of the DMGABA immobilized solvent can control adsorptivity

  6. Reduction of Aldehydes and Ketones by Sodium Dithionite

    NARCIS (Netherlands)

    Vries, Johannes G. de; Kellogg, Richard M.

    1980-01-01

    Conditions have been developed for the effective reduction of aldehydes and ketones by sodium dithionite, Na2S2O4. Complete reduction of simple aldehydes and ketones can be achieved with excess Na2S2O4 in H2O/dioxane mixtures at reflux temperature. Some aliphatic ketones, for example, pentanone and

  7. 2-[(4-Bromophenyliminomethyl]-5-pentadecylphenol

    Directory of Open Access Journals (Sweden)

    Basavaraj Padmashali

    2012-08-01

    Full Text Available 2-[(4-Bromophenyliminomethyl]-5-pentadecylphenol has been synthesized by reaction of 2-hydroxy-4-pentadecylbenzaldehyde with 4-bromoaniline in 1,4-dioxane and its IR, 1H-NMR, 13C-NMR and MS spectroscopic data are presented.

  8. 2-[(4-Bromophenylimino)methyl]-5-pentadecylphenol

    OpenAIRE

    Basavaraj Padmashali; Patchanita Thamyongkit; Amorn Petsom; Gadada Naganagowda

    2012-01-01

    2-[(4-Bromophenylimino)methyl]-5-pentadecylphenol has been synthesized by reaction of 2-hydroxy-4-pentadecylbenzaldehyde with 4-bromoaniline in 1,4-dioxane and its IR, 1H-NMR, 13C-NMR and MS spectroscopic data are presented.

  9. Variations in the heterogeneity of the decay of the fluorescence in six procyanidin dimers

    Science.gov (United States)

    Donghwan Cho; Rujiang Tian; Lawrence J. Porter; Richard W. Hemingway; Wayne L. Mattice

    1990-01-01

    The decay of the fluorescence has been measured in 1,4-dioxane for six dimers of (2R,3R)-(-)-epicatechin and (2R,3S)-(+)-catechin, hereafter denoted simply epicatechin and catechin. The dimers are epicatechin-(4β→8)-catechin, epicatechin-(4β→8)-epicatechin...

  10. Use of the fluorescence quantum yield for the determination of the number-average molecular weight of polymers of epicatechin with 4β→8 interflavin bonds

    Science.gov (United States)

    D. Cho; W.L. Mattice; L.J. Porter; Richard W. Hemingway

    1989-01-01

    Excitation at 280 nm produces a structureless emission band with a maximum at 321-324 nm for dilute solutions of catechin, epicatechin, and their oligomers in l,4-dioxane or water. The fluorescence quantum yield, Q, has been measured in these two solvents for five dimers, a trimer, a tetramer, a pentamer, a hexamer, and a polymer in which the monomer...

  11. Mechanism of Prototropy. V. Arrhenius parameters of the tautomerization of Benzylidene Benzylamine and its {alpha}-{alpha}-alkyl derivatives; Mecanismo de la prototropia V. Parametros de Arrhenius de la toutomerizacion de benciliden-bencilamina y sus {alpha}- y {alpha}-alquilderivados

    Energy Technology Data Exchange (ETDEWEB)

    Perez Ossorio, R; Gomez Herrera, F; Utrilla, R M; Hidalgo, A; Gamboa, J M

    1961-07-01

    The reactions were conducted in ethyl alcohol-dioxan, in the presence of EtONa, as catalyst. Rates were followed by a radioactive tracer method when R=H and by spectroscopic method when R= alkyl as described in previous papers. The results suggest that polar effects alone cannot account for the relative Arrhenius parameters obtained. (Author) 3 refs.

  12. Synthesis and reactivity ratios of regioisomeric vinyl-1,2,3-triazoles with styrene

    NARCIS (Netherlands)

    Lartey, M; Gillissen, M.A.J.; Adzima, B.J.; Takizawa, K.; Luebke, D.R.; Nulwala, H.B.

    2013-01-01

    The free radical reactivity ratios between styrene and different vinyl-1,2,3-triazole regioisomeric monomers in 1,4-dioxane at 65 degrees C have been established using nonlinear least square method. The results obtained for the reactivity ratio between regioisomers show exceptionally different

  13. Mechanism of Prototropy. V. Arrhenius parameters of the tautomerization of Benzylidene Benzylamine and its α-α-alkyl derivatives

    International Nuclear Information System (INIS)

    Perez Ossorio, R.; Gomez Herrera, F.; Utrilla, R. M.; Hidalgo, A.; Gamboa, J. M.

    1961-01-01

    The reactions were conducted in ethyl alcohol-dioxan, in the presence of EtONa, as catalyst. Rates were followed by a radioactive tracer method when R=H and by spectroscopic method when R= alkyl as described in previous papers. The results suggest that polar effects alone cannot account for the relative Arrhenius parameters obtained. (Author) 3 refs

  14. Solution small-angle x-ray scattering as a screening and predictive tool in the fabrication of asymmetric block copolymer membranes

    KAUST Repository

    Dorin, Rachel Mika; Marques, Debora S.; Sai, Hiroaki; Vainio, Ulla; Phillip, William A.; Peinemann, Klaus; Nunes, Suzana Pereira; Wiesner, Ulrich B.

    2012-01-01

    Small-angle X-ray scattering (SAXS) analysis of the diblock copolymer poly(styrene-b-(4-vinyl)pyridine) in a ternary solvent system of 1,4-dioxane, tetrahydrofuran, and N,N-dimethylformamide, and the triblock terpolymer poly(isoprene-b-styrene-b-(4-vinyl)-pyridine) in a binary solvent system of 1,4-dioxane and tetrahydrofuran, reveals a concentration-dependent onset of ordered structure formation. Asymmetric membranes fabricated from casting solutions with polymer concentrations at or slightly below this ordering concentration possess selective layers with the desired nanostructure. In addition to rapidly screening possible polymer solution concentrations, solution SAXS analysis also predicts hexagonal and square pore lattices of the final membrane surface structure. These results suggest solution SAXS as a powerful tool for screening casting solution concentrations and predicting surface structure in the fabrication of asymmetric ultrafiltration membranes from self-assembled block copolymers. (Figure presented) © 2012 American Chemical Society.

  15. Near-infrared Raman spectroscopy using a diode laser and CCD detector for tissue diagnostics

    International Nuclear Information System (INIS)

    Gustafsson, U.

    1993-09-01

    This paper surveys the possibility to observe high-quality NIR Raman spectra of both fluorescent and non-fluorescent samples with the use of a diode laser, a fibre optic sample, a single spectrometer and a charge-coupled device (CCD) detector. A shifted excitation difference technique was implemented for removing the broad-band fluorescence emission from Raman spectra of the highly fluorescent samples. Raman spectra of 1.4-dioxane, toluene, rhodamine 6G, and HITCI in the 640 to 1840 cm -1 spectral region and 1.4-dioxane and toluene in the 400 to 3400 cm -1 spectral region have been recorded. The results open the field of sensitive tissue characterisation and the possibility of optical biopsy in vivo by using NIR Raman spectroscopy with fibre optic sampling, a single spectrometer, and a CCD detector

  16. The solvation of L-serine in mixtures of water with some aprotic solvents at 298.15 K

    Science.gov (United States)

    Mezhevoi, I. N.; Badelin, V. G.

    2009-03-01

    The integral enthalpies of solution Δsol H m of L-serine in mixtures of water with acetonitrile, 1,4-dioxane, dimethylsulfoxide (DMSO), and acetone were measured by solution calorimetry at organic component concentrations up to 0.31 mole fractions. The standard enthalpies of solution (Δsol H°), transfer (Δtr H°), and solvation (Δsolv H°) of L-serine from water into mixed solvents were calculated. The dependences of Δsol H°, Δsolv H°, and Δtr H° on the composition of aqueous-organic solvents contained extrema. The calculated enthalpy coefficients of pair interactions of the amino acid with cosolvent molecules were positive and increased in the series acetonitrile, 1,4-dioxane, DMSO, acetone. The results obtained were interpreted from the point of view of various types of interactions in solutions and the influence of the nature of organic solvents on the thermochemical characteristics of solutions.

  17. Thermodynamics of the second-stage dissociation of 2-[N-(2-hydroxyethyl)-N-methylaminomethyl]-propenoic acid (HEMPA) in water at different ionic strength and different solvent mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Taha, Mohamed [Department of Chemistry, Faculty of Science, Cairo University, Beni-Suef Branch, Beni-Suef (Egypt)]. E-mail: mtaha978@yahoo.com; Fazary, Ahmed E. [Department of Chemistry, Faculty of Science, Cairo University, Beni-Suef Branch, Beni-Suef (Egypt)

    2005-01-01

    The second stage dissociation constant pK{sub 2} of 2-[N-(2-hydroxyethyl)-N-methylaminomethyl]-propenoic acid (HEMPA) has been determined in aqueous solution at different ionic strengths and different temperatures, using pH-metric technique. The thermodynamic quantities ({delta}G{sup 0}, {delta}H{sup 0}, and {delta}S{sup 0}) have been studied and discussed. Evaluation of the effect of organic solvent of the medium on the dissociation processes have also been reported and discussed. The organic solvents used were methanol, dimethylformamide (DMF), dimethylsulfoxide (DMSO), acetone and dioxane. The pK{sub 2} for the ionization in water +10, +20, +30, +40 and +50 wt% dioxane has been determined at five different temperatures from T = (288.15 to 308.15) K at intervals of 5 K. The thermodynamic quantities were calculated. The implications of the results with regard to specific (solute + solvent) interactions (particularly stabilization of zwitterionic species) are also discussed.

  18. Thermodynamics of the second-stage dissociation of 2-[N-(2-hydroxyethyl)-N-methylaminomethyl]-propenoic acid (HEMPA) in water at different ionic strength and different solvent mixtures

    International Nuclear Information System (INIS)

    Taha, Mohamed; Fazary, Ahmed E.

    2005-01-01

    The second stage dissociation constant pK 2 of 2-[N-(2-hydroxyethyl)-N-methylaminomethyl]-propenoic acid (HEMPA) has been determined in aqueous solution at different ionic strengths and different temperatures, using pH-metric technique. The thermodynamic quantities (ΔG 0 , ΔH 0 , and ΔS 0 ) have been studied and discussed. Evaluation of the effect of organic solvent of the medium on the dissociation processes have also been reported and discussed. The organic solvents used were methanol, dimethylformamide (DMF), dimethylsulfoxide (DMSO), acetone and dioxane. The pK 2 for the ionization in water +10, +20, +30, +40 and +50 wt% dioxane has been determined at five different temperatures from T = (288.15 to 308.15) K at intervals of 5 K. The thermodynamic quantities were calculated. The implications of the results with regard to specific (solute + solvent) interactions (particularly stabilization of zwitterionic species) are also discussed

  19. Solution small-angle x-ray scattering as a screening and predictive tool in the fabrication of asymmetric block copolymer membranes

    KAUST Repository

    Dorin, Rachel Mika

    2012-05-15

    Small-angle X-ray scattering (SAXS) analysis of the diblock copolymer poly(styrene-b-(4-vinyl)pyridine) in a ternary solvent system of 1,4-dioxane, tetrahydrofuran, and N,N-dimethylformamide, and the triblock terpolymer poly(isoprene-b-styrene-b-(4-vinyl)-pyridine) in a binary solvent system of 1,4-dioxane and tetrahydrofuran, reveals a concentration-dependent onset of ordered structure formation. Asymmetric membranes fabricated from casting solutions with polymer concentrations at or slightly below this ordering concentration possess selective layers with the desired nanostructure. In addition to rapidly screening possible polymer solution concentrations, solution SAXS analysis also predicts hexagonal and square pore lattices of the final membrane surface structure. These results suggest solution SAXS as a powerful tool for screening casting solution concentrations and predicting surface structure in the fabrication of asymmetric ultrafiltration membranes from self-assembled block copolymers. (Figure presented) © 2012 American Chemical Society.

  20. Complex formation of hypoxanthine and 6-mercaptopurine with Cd(II) ion

    International Nuclear Information System (INIS)

    Perello, L.; Borras, J.; Soto, L.; Gordo, F.J.; Gordo, J.C.

    1984-01-01

    Reaction of Cd(II) ion with hypoxanthine (H 2 Y) and with 6-mercaptopurine (H 2 MP) in dioxane-water (50%) leads to the formation of CdY x 2H 2 O and Cd(HMP) 2 x 2H 2 O, respectively. In methanolic medium Cd(II) and H 2 MP give Cd(MP) x H 2 O. These compounds have been characterized by chemical analysis, IR spectra and thermogravimetric analysis. The stability constant of CdY complex at 25 +- 0.1 0 C and 1M ionic strength with NaClO 4 in dioxane-water medium is logβ = 10.25 +- 0.05. (Author)

  1. Complex formation of hypoxanthine and 6-mercaptopurine with Cd(II) ion

    Energy Technology Data Exchange (ETDEWEB)

    Perello, L.; Borras, J.; Soto, L.; Gordo, F.J.; Gordo, J.C. (Valencia Univ. (Spain))

    1984-01-01

    Reaction of Cd(II) ion with hypoxanthine (H/sub 2/Y) and with 6-mercaptopurine (H/sub 2/MP) in dioxane-water (50%) leads to the formation of CdY x 2H/sub 2/O and Cd(HMP)/sub 2/ x 2H/sub 2/O, respectively. In methanolic medium Cd(II) and H/sub 2/MP give Cd(MP) x H/sub 2/O. These compounds have been characterized by chemical analysis, IR spectra and thermogravimetric analysis. The stability constant of CdY complex at 25 +- 0.1/sup 0/C and 1M ionic strength with NaClO/sub 4/ in dioxane-water medium is log..beta.. = 10.25 +- 0.05.

  2. Immobilization of enzymes by radiation-induced polymerization of glass-forming monomers

    International Nuclear Information System (INIS)

    Yoshida, M.; Kumakura, M.; Kaetsu, I.

    1979-01-01

    The effect of cooling rate of a monomeric system on the porosity and activity of an immobilized enzyme prepared by radiation-induced polymerization of 2-hydroxyethyl methacrylate at low temperatures has been studied. Slow cooling gave the same effect on porosity of the polymer as decreasing the monomer concentration. A glass-forming solvent such as diethylene glycol was added to water to study the effect of the supercooling tendency of the solvent. Addition of diethylene glycol decreased porosity and also enzymic activity. Water was replaced by the miscible solvent p-dioxane and the immiscible solvent n-decane in order to clarify the effect of solvent. p-Dioxane had a similar effect to water on the relation between the monomer concentration, porosity and activity. On the other hand, polymer prepared from the system containing n-decane showed different immobilization properties owing to the presence of independent pores in the matrix. (author)

  3. 5-Arylidene derivatives of Meldrum's acid: Synthesis, structural characterization using single crystal and powder crystal X-ray diffraction, and electronic properties

    Science.gov (United States)

    Dey, Tanusri; Ghosh, Soumen; Ghosh, Somnath; Mukherjee, Alok Kumar

    2015-07-01

    Four 5-arylidene derivatives of Meldrum's acid, 5-(4-chlorobenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (2), 5-(3-hydroxybenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (3), 5-(3,4-dimethoxybenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (4) and 5-(2,4-dimethoxy benzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (5) have been synthesized and their crystal structures have been determined using single crystal X-ray diffractometry for 2, 4 and 5 and X-ray powder diffraction for 3. The nature of intermolecular interactions in 2-5 has been analyzed through Hirshfeld surfaces and 2D fingerprint plots. The DFT optimized molecular geometries in 2-5 agree closely with those obtained from the crystallographic studies. The crystal packing in 2-5 exhibits an interplay of Osbnd H⋯O, Csbnd H⋯O, Csbnd H⋯Cl and Csbnd H⋯π (arene) hydrogen bonds and π⋯π interactions, which assemble molecules into three-dimensional architecture in 2, 3 and 5 and two-dimensional framework in 4. The Hirshfeld surface analyses of 2-5, Meldrum's acid (1) and a few related 5-arylidene derivatives of Meldrum's acid retrieved from the Cambridge Structural Database (CSD) indicate that about 85% of the Hirshfeld surface area (72% in 2 where H⋯Cl contribution is about 13%) in this class of compounds are due to H⋯H, O⋯H and C⋯H contacts. The HOMO-LUMO energy gap (>2.2 eV) in 2-5 indicates a significant degree of internal charge transfer within the molecule.

  4. Zwitterionic and free forms of arylmethyl Meldrum's acids.

    Science.gov (United States)

    Mierina, Inese; Mishnev, Anatoly; Jure, Mara

    2015-09-01

    C-Alkyl (including C-arylmethyl) derivatives of Meldrum's acids are attractive building blocks in organic synthesis, mainly due to the unusually high acidity of the resulting compounds. Three examples, namely 5-[4-(diethylamino)benzyl]-2,2-dimethyl-1,3-dioxane-4,6-dione, C17H23NO4, (I), 2,2-dimethyl-5-(2,4,6-trimethoxybenzyl)-1,3-dioxane-4,6-dione, C16H20O7, (II), and 5-(4-hydroxy-3,5-dimethoxybenzyl)-2,2-dimethyl-1,3-dioxane-4,6-dione, C15H18O7, (III), have been synthesized, characterized by NMR and IR spectroscopy, and studied by single-crystal X-ray structure analysis. The nature of the different substituents resulted in remarkable differences in both the molecular conformations and the crystal packing arrangements. The presence of a substituent with a basic centre in compound (I) leads to the formation of an inner salt accompanied by drastic changes in the conformation of the 1,3-dioxane-4,6-dione fragment. By virtue of strong N-H···O hydrogen bonds, the residues are assembled into infinite chains with the graph-set descriptor C(10). Compound (II) contains methoxy groups in both the ortho- and para-positions of the arylmethyl fragment. Because of the absence of classical hydrogen-bond donors in this structure, the crystal packing is controlled by van der Waals forces and weak C-H···O interactions. Compound (III) contains methoxy groups in both meta-positions and a hydroxy group in the para-position. Supramolecular tetrameric synthons which comprise hydrogen-bonded dimers associated into tetramers through π-π interactions of overlapping benzene rings were observed.

  5. Informal Conference on Photochemistry Held in Atlanta, Georgia on 26 April-1 May, 1992

    Science.gov (United States)

    1992-05-01

    of the kinetics of such reactions. We have measured rate constants for the neopentyl peroxy radical, generating the alkyl radical by laser flash... glycol diacetate) > Ketones(acetone.acetophenone) > Ethers(tetrahydrofuran. dioxane). Nltrlles(acetonltrlle).Halogenated hydrocarbons (carbon...the best solvent to synthesis of CBDA. especially ethyl acetate (Y63% /KW Hr) and ethylene glycol diacetate (Y55,/lW Hr).i (2) TEMPERATURE CBDA yield

  6. Kinetics and mechanism of polymerization of methyl methacrylate ...

    Indian Academy of Sciences (India)

    Homopolymerization of methyl methacrylate (MMA) was carried out in the presence of triphenylstibonium 1,2,3,4-tetraphenyl-cyclopentadienylide as an initiator in dioxane at 65°C ± 0·1°C. The system follows non-ideal radical kinetics ( ∝ [M]1.4 [I]0.44) due to primary radical termination as well as degradative ...

  7. Preparation of 45Ca(HDEHP)n and (CaH1502)2 samples for liquid scintillation counting, compared to 45caCl2 results

    International Nuclear Information System (INIS)

    Rodriguez, L.; Arcos, J. M. los; Grau Malonda, A.

    1994-01-01

    A procedure for preparation of liquid scintillation counting organic samples of the Di-2-ethylhexyl phosphate calcium complex and the 2-ethylhexanoate calcium salt, labelled with 45Ca, is described. The chemical quench, the counting stability and spectral evolution of both compounds is studied in six scintillators,Toluene-alcohol, Dioxane-naphtalene, Hi safe II, Ultimate-Gold and Instagel, and compared to results obtained from a commercial solution of 4 5CaCl2. (Author) 7 refs

  8. Preparation of 45 Ca (HDEHP)n and (C8H15O2)2 samples for liquid scintillation counting, compared to 45CaCl2 results

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Los Arcos Merino, J.M.; Grau Malonda, A.

    1994-01-01

    A procedure for preparation of liquid scintillation counting organic samples of the Di-2-ethylhexyl phosphate calcium complex and the 2-ethyhexanoate calcium salt, labelled with ''45 Ca, is described. The chemical quench, the counting stability and spectral evolution of both compounds is studied in six scintillators, Toluene, Toluene-alcohol, Dioxane-napthalhene, Hisafe II, Ultima-Gold and Instagel, and compared to results obtained from a commercial solution of ''45 CaCl 2

  9. Preparation of 45Ca(HDEHP)n and (CaH{sub 1}50{sub 2})2 samples for liquid scintillation counting, compared to 45caCl{sub 2} results; Preparacion de Ca (HDEHP)n y (C{sub 8}H{sub 1}50{sub 2})2 marcados con 45Ca y estudio comparativo con 4 5ca Cl2 en medidas por centelleo liquido

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, L.; Arcos, J. M. los; Grau Malonda, A.

    1994-07-01

    A procedure for preparation of liquid scintillation counting organic samples of the Di-2-ethylhexyl phosphate calcium complex and the 2-ethylhexanoate calcium salt, labelled with 45Ca, is described. The chemical quench, the counting stability and spectral evolution of both compounds is studied in six scintillators,Toluene-alcohol, Dioxane-naphtalene, Hi safe II, Ultimate-Gold and Instagel, and compared to results obtained from a commercial solution of 4 5CaCl2. (Author) 7 refs.

  10. SERDP and ESTCP Workshop on Long Term Management of Contaminated Groundwater Sites

    Science.gov (United States)

    2013-11-01

    contaminant level MNA monitored natural attenuation NDMA N-nitrosodimethylamine NRC National Research Council ORP oxidation reduction potential...of importance, were per- and polyfluoroalkyl substances (PFASs), 1,4-dioxane, 1,2,3-trichloropropane (1,2,3-TCP) and N-nitrosodimethylamine ( NDMA ...significant concern. Similarly, SERDP and ESTCP have funded several studies on NDMA , but recently released reports have revealed new data on NDMA occurrence

  11. Effect of hydrostatic pressure, temperature, and solvent on the rate of the Diels-Alder reaction between 9,10-anthracenedimethanol and maleic anhydride

    Science.gov (United States)

    Kiselev, V. D.; Kornilov, D. A.; Anikin, O. V.; Latypova, L. I.; Konovalov, A. I.

    2017-03-01

    The rate of the reaction between 9,10-anthracenedimethanol and maleic anhydride in 1,4-dioxane, acetonitrile, trichloromethane, and toluene is studied at 25, 35, 45°C in the pressure range of 1-1772 bar. The rate constants, enthalpies, entropies and activation volumes are determined. It is shown that the rate of reaction with 9,10-anthracenedimethanol is approximately one order of magnitude higher than with 9-anthracenemethanol.

  12. Cubane Derivatives for Propellant Applicationsxb

    Science.gov (United States)

    1989-07-03

    cycloperitanone ketal containing 2-3% cyclopentanone and trace amounts of toluene. Approximately 4 liters of purified cyclopentanone ketal per day could be...such as reaction with trimethyl phosphite , also gave inconsistent results. In reactions involving 45 moles of ketal in a 20 gallon Pfaudler reactor...Dioxane treated with trimethyl phosphite Dehydrohalogenation and Dimerization of the Tribromo Ketal to the Bisketal. In-0 0 stop 3 0 Gr r or [to"t

  13. Novel, Solvent-Free, Single Ion Conductive Polymer Electrolytes

    Science.gov (United States)

    2008-01-20

    liquid oligomeric analogue PEODME (ε = 8, dioxane:CH3CN mass ratio 48:7). The choice of the solvent mixture was a compromise between the...trifluoride – a derivative of Lewis acid properties. An increase in the degree of dissociation, decrease in the share of ionic associates and increase in...diphenylphosphinate this product is a solid, and in reaction with lithium diphenylphosphate the second fraction is a viscous, light-brown liquid , and

  14. Interaction probability value calculi for some scintillators

    International Nuclear Information System (INIS)

    Garcia-Torano Martinez, E.; Grau Malonda, A.

    1989-01-01

    Interaction probabilities for 17 gamma-ray energies between 1 and 1.000 KeV have been computed and tabulated. The tables may be applied to the case of cylindrical vials with radius 1,25 cm and volumes 5, 10 and 15 ml. Toluene, Toluene/Alcohol, Dioxane-Naftalen, PCS, INSTAGEL and HISAFE II scintillators are considered. Graphical results for 10 ml are also given. (Author) 11 refs

  15. Gamma-Ray interaction probabilities for some liquid scintillators

    International Nuclear Information System (INIS)

    Garcia-Torano Martinez, E.; Grau Malonda, A.

    1989-01-01

    Interaction probabilities for 17 gamma-Ray energies between 1 and 1.000 KeV have been computed and tabulated. The tables may be applied to the case of cylindrical vials with radius 1,25 cm and volumes 5, 10 and 15 ml. Toluene, Toluene/Alcohol, Dioxane-Naftalene, PCS, INSTAGEL and HISAFE II scintillators are considered. Graphical results for 10 ml are also given. (Author)

  16. Preparation of manganese salts of carboxylic acids labelled with ''54Mn and comparison with ''54 MnCl2 in liquid scintillation counting

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Arcos Merino, J. M. los; Grau Malonda, A.

    1992-01-01

    Procedures for liquid scintillation sample preparation of manganese dimethylbutirate, decanoate and palmitate, labelled with 54 Mn are described. their quenching effect, spectral evolution and counting stability along several weeks are analysed in liquid scintillation measurements with Toluene. HISafe II. PCS, instagel. Dioxane-naphtalene and Toluene-alcohol. For comparison, Inorganic 54 MnCl-2 samples are also studied, resulting in acceptable counting stability but showing greater quenching and signs of little spectral degradation against the organic samples. (Author)

  17. Thermal Decomposition Reaction of Acetophenone Cyclic Diperoxide in Solvents of Different Physicochemical Properties

    Directory of Open Access Journals (Sweden)

    C. M. Mateo

    2000-03-01

    Full Text Available The thermal decomposition reaction of acetophenone cyclic diperoxide (trans-3,6-dimethyl-3,6-diphenyl-1,2,4,5-tetroxane; APDP at the initial concentration of c.a. 0.01 mol kg-1 and temperature ranges of 135.5 to 185.0° C has been investigated in dioxane and acetonitrile solutions, and in an 2-propanol/benzene mixture.

  18. Synthesis of dye/fluorescent functionalized dendrons based on cyclotriphosphazene

    Directory of Open Access Journals (Sweden)

    Aurélien Hameau

    2011-11-01

    Full Text Available Functionalized phenols based on tyramine were synthesized in order to be selectively grafted on to hexachlorocyclotriphosphazene, affording a variety of functionalized dendrons of type AB5. The B functions comprised fluorescent groups (dansyl or dyes (dabsyl, whereas the A function was provided by either an aldehyde or an amine. The characterization of these dendrons is reported. An unexpected behaviour of a fluorescent and water-soluble dendron based on dansyl groups in mixtures of dioxane/water was observed.

  19. Preparation of manganese salts of carboxylic acids labelled with ''54Mn and comparison with ''54 MnCl{sub 2} in liquid scintillation counting; Preparacion de sales manganosas de acidos alifaticos monocarboxilicos marcados con ''54 MnCl{sub 2} en medidas por centelleo liquido

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Barquero, L.; Arcos Merino, J. M. los; Grau Malonda, A.

    1992-07-01

    Procedures for liquid scintillation sample preparation of manganese dimethylbutirate, decanoate and palmitate, labelled with 54 Mn are described. their quenching effect, spectral evolution and counting stability along several weeks are analysed in liquid scintillation measurements with Toluene. HISafe II. PCS, instagel. Dioxane-naphtalene and Toluene-alcohol. For comparison, Inorganic 54 MnCl-2 samples are also studied, resulting in acceptable counting stability but showing greater quenching and signs of little spectral degradation against the organic samples. (Author)

  20. Surface study of mixtures containing cyclic ethers and isomeric chlorobutanes

    International Nuclear Information System (INIS)

    Royo, F.M.; Villares, A.; Martin, S.; Giner, B.; Lafuente, C.

    2007-01-01

    Experimental surface tensions and the corresponding surface tensions deviations for the mixtures containing 1,3-dioxolane or 1,4-dioxane and 1-chlorobutane, 2-chlorobutane, 1-chloro-2-methylpropane or 2-chloro-2-methylpropane, measured with a drop volume tensiometer, are reported at the temperatures of 298.15 K and 313.15 K. The excess surface concentrations of isomeric chlorobutanes are also evaluated using a monolayer model

  1. Solid–liquid equilibria for binary and ternary systems with the Cubic-Plus-Association (CPA) equation of state

    DEFF Research Database (Denmark)

    Fettouhi, André; Thomsen, Kaj

    2010-01-01

    A systematic investigation of the CPA model's performance within solid-liquid equilibria (SLE) in binary mixtures (methane + ethane, methane + heptane, methane + benzene, methane + CO2, ethane + heptane, ethane + CO2, 1-propanol + 1,4-dioxane, ethanol + water, 2-propanol + water) is presented. Th....... The results from the binary mixtures are used to predict SLE behaviour in ternary mixtures (methane + ethane + heptane, methane + ethane + CO2). Our results are compared with experimental data found in the literature....

  2. Preparation and mechanical property of polymer-based biomaterials

    International Nuclear Information System (INIS)

    Zhang, P; Chen, G; Zheng, X F

    2010-01-01

    The porous polymer-based biomaterial has been synthesized from PLGA, dioxane and tricalcium phosphate (TCP) by low-temperature deposition process. The deformation behaviours and fracture mechanism of polymer-based biomaterials were investigated using the compression test and the finite element (FE) simulation. The results show that the stress-strain curve of compression process includes linear elastic stage I, platform stage II and densification stage III, and the fracture mechanism can be considered as brittle fracture.

  3. Iodine-catalyzed sp³ C-H bond activation by selenium dioxide: synthesis of diindolylmethanes and di(3-indolyl)selanides.

    Science.gov (United States)

    Naidu, P Seetham; Majumder, Swarup; Bhuyan, Pulak J

    2015-11-01

    An efficient reaction protocol was developed for the synthesis of several diindolylmethane derivatives via the [Formula: see text] C-H bond activation of aryl methyl ketones by [Formula: see text] and indoles in the presence of catalytic amounts of [Formula: see text] at 80 [Formula: see text] using dioxane as solvent. Unexpectedly, an interesting class of di(3-indolyl)selenide compounds was isolated when the reaction was carried out at room temperature.

  4. Glycerol acetals, kinetic study of the reaction between glycerol and formaldehyde

    International Nuclear Information System (INIS)

    Agirre, I.; Garcia, I.; Requies, J.; Barrio, V.L.; Gueemez, M.B.; Cambra, J.F.; Arias, P.L.

    2011-01-01

    The acetalization reaction between glycerol and formaldehyde using Amberlyst 47 acidic ion exchange resin was studied. These acetals can be obtained from renewable sources (bioalcohols and bioalcohol derived aldehydes) and seem to be good candidates for different applications such as oxygenated diesel additives. A preliminary kinetic study was performed in a batch stirred tank reactor studying the influence of different process parameters like temperature, feed composition and the stirring speed. A pseudo homogenous kinetic model able to explain the reaction mechanism was adjusted. Thus, the corresponding order of reaction was determined. Amberlyst 47 acidic ion exchange resin showed a fairly good behavior allowing 100% of selectivity towards acetals formation. However, the studied acetalization reaction showed high thermodynamic limitations achieving glycerol conversions around 50% using a stoichiometric feed ratio at 353 K. The product is a mixture of two isomers (1,3-Dioxan-5-ol and 1,3-dioxolane-4-methanol) and the conversion of 1,3-dioxolane-4-methanol into 1,3-Dioxan-5-ol was also observed. -- Highlights: → The reaction between glycerol and acetaldehyde shows thermodynamic limitations. → Amberlyst 47 ion exchange resins show 100% of selectivity. → A pseudo-homogeneous kinetic model is able to predict the reaction progress. → Isomerization reactions were observed from dioxalanes to dioxanes.

  5. Alkaline and Organosolv Lignins from Furfural Residue: Structural Features and Antioxidant Activity

    Directory of Open Access Journals (Sweden)

    Xue-Fei Cao

    2013-12-01

    Full Text Available Furfural residue (FR, composed mainly of cellulose and lignin, is an industrial waste produced during furfural manufacture. In this study, dioxane, alkali, ethanol, alkali-ethanol, and alkaline hydrogen peroxide (AHP were used to extract lignins from FR. The structural features of these lignins obtained were characterized by sugar analysis, GPC, UV, FT-IR, and HSQC spectra. As compared to dioxane lignin (DL, other lignins showed lower molecular weights (Mw owing to the partial cleavage of the linkages between lignin units. Results from HSQC spectra revealed that β-O-4' and β-5' were still the major linkages of the FR lignin. Moreover, p-coumaric and ferulic acids were released and co-precipitated in the lignin preparations extracted with alkali and AHP, whereas part of the esters in DL were preserved during the dioxane extraction. Antioxidant activity investigation indicated that the antioxidant property of the alkali and alkali-ethanol lignins was higher than that of the commercial antioxidant, butylated hydroxytoluene.

  6. Kinetic α secondary deuterium isotope effects for O-ethyl S-phenyl benzaldehyde acetal hydrolysis

    International Nuclear Information System (INIS)

    Ferraz, J.P.; Cordes, E.H.

    1979-01-01

    The rate of hydrolysis of O-ethyl S-phenyl benzaldehyde acetal at 25 0 C in 20% dioxane--80% water is independent of pH over the range pH6-12; k/sub obsd/ = 1.9 x 10 -7 s -1 . Under more acidic conditions, the rate increases linearly with the activity of the hydrated proton; k 2 = 2.95 x 10 -2 M -1 s -1 . The kinetic α secondary deuterium isotope effect for acid-catalyzed hydrolysis of O-ethyl S-phenyl benzaldehyde acetal, measured at 25 0 C in 20% aqueous dioxane containing 0.05 M HCl, is k/sub H//k/sub D/ = 1.038 +- 0.008, a value consistent with a transition state in which the C--S bond is stretched rather little. In contrast, the corresponding isotope effect for the pH-independent hydrolysis of this substrate, measured at 42.5 0 C in 20% dioxane, is 1.13 +- 0.02, a value consistent with complete C--S bond cleavage in the transition state and rate-determining diffusion apart of the ion-pair formed as the initial intermediate, in accord with the suggestion of Jensen and Jencks. 1 figure, 4 tables

  7. Proposing nanofiltration as acceptable barrier for organic contaminants in water reuse

    KAUST Repository

    Yangali-Quintanilla, Victor

    2010-10-01

    For water reuse applications, " tight" nanofiltration (NF) membranes (of polyamide) as an alternative to reverse osmosis (RO) can be an effective barrier against pharmaceuticals, pesticides, endocrine disruptors and other organic contaminants. The use of RO in existing water reuse facilities is addressed and questioned, taking into consideration that tight NF can be a more cost-effective and efficient technology to target the problem of organic contaminants. It was concluded that tight NF is an acceptable barrier for organic contaminants because its removal performance approaches that of RO, and because of reduced operation and maintenance (O&M) costs in long-term project implementation. Average removal of neutral compounds (including 1,4-dioxane) was about 82% and 85% for NF and RO, respectively, and average removal of ionic compounds was about 97% and 99% for NF and RO, respectively. In addition, " loose" NF after aquifer recharge and recovery (ARR) can be an effective barrier against micropollutants with removals over 90%. When there is the presence of difficult to remove organic contaminants such as NDMA and 1,4-dioxane; for 1,4-dioxane, source control or implementation of treatment processes in wastewater treatment plants will be an option; for NDMA, a good strategy is to limit its formation during wastewater treatment, but there is evidence that biodegradation of NDMA can be achieved during ARR. © 2010 Elsevier B.V.

  8. Electronic spectra and DFT calculations of some pyrimido[1,2-a]benzimidazole derivatives

    Science.gov (United States)

    Elshakre, Mohamed E.; Moustafa, H.; Hassaneen, Huwaida. M. E.; Moussa, Abdelrahim. Z.

    2015-06-01

    Ground state properties of 2,4-diphenyl-1,4-dihydrobenzo[4,5]imidazo[1,2-a]pyrimidine, compound 1, and its derivatives are investigated experimentally and theoretically in Dioxane and DMF. The calculations show that all the studied compounds (1-7) are non-planar, resulting in a significant impact on the electronic and structural properties. The ground state properties of compounds 1-7 at B3LYP/6-311G (d, p) show that compound 5 has the lowest EHOMO, ELUMO, and ΔE indicating highest reactivity. Compound 7 is found to have the highest polarity. The observed UV spectra in Dioxane and DMF of compounds 1-4 show 2 bands, while compounds 5-7 show 4 bands in both solvents. Band maxima (λmax) and intensities of the spectra are found to have solvent dependence reflected as blue and red shifts. The theoretical spectra computed at TD-B3LYP/6-311G (d, p) in gas phase, Dioxane and DMF indicate a good agreement with the observed spectra.

  9. Structural and Magnetic Diversity in Alkali-Metal Manganate Chemistry: Evaluating Donor and Alkali-Metal Effects in Co-complexation Processes.

    Science.gov (United States)

    Uzelac, Marina; Borilovic, Ivana; Amores, Marco; Cadenbach, Thomas; Kennedy, Alan R; Aromí, Guillem; Hevia, Eva

    2016-03-24

    By exploring co-complexation reactions between the manganese alkyl Mn(CH2SiMe3)2 and the heavier alkali-metal alkyls M(CH2SiMe3) (M=Na, K) in a benzene/hexane solvent mixture and in some cases adding Lewis donors (bidentate TMEDA, 1,4-dioxane, and 1,4-diazabicyclo[2,2,2] octane (DABCO)) has produced a new family of alkali-metal tris(alkyl) manganates. The influences that the alkali metal and the donor solvent impose on the structures and magnetic properties of these ates have been assessed by a combination of X-ray, SQUID magnetization measurements, and EPR spectroscopy. These studies uncover a diverse structural chemistry ranging from discrete monomers [(TMEDA)2 MMn(CH2SiMe3)3] (M=Na, 3; M=K, 4) to dimers [{KMn(CH2SiMe3)3 ⋅C6 H6}2] (2) and [{NaMn(CH2SiMe3)3}2 (dioxane)7] (5); and to more complex supramolecular networks [{NaMn(CH2SiMe3)3}∞] (1) and [{Na2Mn2 (CH2SiMe3)6 (DABCO)2}∞] (7)). Interestingly, the identity of the alkali metal exerts a significant effect in the reactions of 1 and 2 with 1,4-dioxane, as 1 produces coordination adduct 5, while 2 forms heteroleptic [{(dioxane)6K2Mn2 (CH2SiMe3)4(O(CH2)2OCH=CH2)2}∞] (6) containing two alkoxide-vinyl anions resulting from α-metalation and ring opening of dioxane. Compounds 6 and 7, containing two spin carriers, exhibit antiferromagnetic coupling of their S=5/2 moments with varying intensity depending on the nature of the exchange pathways. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Aqueous foam toxicology evaluation and hazard review

    Energy Technology Data Exchange (ETDEWEB)

    Archuleta, M.M.

    1995-10-01

    Aqueous foams are aggregates of bubbles mechanically generated by passing air or other gases through a net, screen, or other porous medium that is wetted by an aqueous solution of surface-active foaming agents (surfactants). Aqueous foams are important in modem fire-fighting technology, as well as for military uses for area denial and riot or crowd control. An aqueous foam is currently being developed and evaluated by Sandia National Laboratories (SNL) as a Less-Than-Lethal Weapon for the National Institute of Justice (NIJ). The purpose of this study is to evaluate the toxicity of the aqueous foam developed for the NIJ and to determine whether there are any significant adverse health effects associated with completely immersing individuals without protective equipment in the foam. The toxicity of the aqueous foam formulation developed for NIJ is determined by evaluating the toxicity of the individual components of the foam. The foam is made from a 2--5% solution of Steol CA-330 surfactant in water generated at expansion ratios ranging from 500:1 to 1000:1. SteoI CA-330 is a 35% ammonium laureth sulfate in water and is produced by Stepan Chemical Company and containing trace amounts (<0.1%) of 1,4-dioxane. The results of this study indicate that Steol CA-330 is a non-toxic, mildly irritating, surfactant that is used extensively in the cosmetics industry for hair care and bath products. Inhalation or dermal exposure to this material in aqueous foam is not expected to produce significant irritation or systemic toxicity to exposed individuals, even after prolonged exposure. The amount of 1,4-dioxane in the surfactant, and subsequently in the foam, is negligible and therefore, the toxicity associated with dioxane exposure is not significant. In general, immersion in similar aqueous foams has not resulted in acute, immediately life-threatening effects, or chronic, long-term, non-reversible effects following exposure.

  11. Studies on the decomposition of ethyl diazoacetate and its reaction with coal. Formation of a new tetrameric product and reagent access within the coal

    Energy Technology Data Exchange (ETDEWEB)

    Pomerantz, M.; Rooney, P.

    A new tetrameric pyrazoline, 10, has been observed in the thermal and Fe/sub 2/O/sub 3/-catalyzed decomposition of ethyl diazoacetate (2) as well as when several coal samples were treated thermally with 2 under various conditions. Identification of 10 was based on spectral properties and an independent synthesis. A comparison of the amounts of diethyl fumarate (3), diethyl maleate (4), the trimeric pyrazoline 5, triethyl trans-cyclopropane-1,2,3-tricarboxylate (8), and the tetrameric pyrazoline 10 formed in the coal reactions with the relative quantities produced in the thermal and Fe/sub 2/O/sub 3/-catalyzed reactions of 2, both neat and diluted with p-xylene, showed that there were several successive and competing reactions occurring, one of which was independent of the concentration of 2. Further, on the basis of the observation that the product distribution of 3-5, 8, and 10 in the Fe/sub 2/O/sub 3/-catalyzed decomposition of 2 in relatively dilute solution is similar to that observed in the coal reactions, with cyclopropane 8 being the major product in both cases, and that 2 is reacting mainly with the coal, it is concluded that 2 is fairly well dispersed within the coal. In addition, it is clear that swelling of the coal with dioxane did very little to facilitate access of 2 into the coal. Instead the dioxane merely acted to allow for more complete extraction of the products after 2 had reacted with the coal, presumably by keeping the matrix structure more open, than when the dioxane was not used. 26 refs., 2 tabs.

  12. Temperature-Invariant Aqueous Microgels as Hosts for Biomacromolecules.

    Science.gov (United States)

    Mastour Tehrani, Sepehr; Lu, Yijie; Guerin, Gerald; Soleimani, Mohsen; Pichugin, Dmitry; Winnik, Mitchell A

    2015-10-12

    Immobilization of enzymes on solid supports has been widely used to improve enzyme recycling, enzyme stability, and performance. We are interested in using aqueous microgels (colloidal hydrogels) as carriers for enzymes used in high-temperature reactions. These microgels should maintain their volume and colloidal stability in aqueous media up to 100 °C to serve as thermo-stable supports for enzymes. For this purpose, we prepared poly(N-hydroxyethyl acrylamide) (PHEAA) microgels via a two-step synthesis. First, we used precipitation polymerization in water to synthesize colloidal poly(diethylene glycol-ethyl ether acrylate) (PDEGAC) particles as a precursor. PDEGAC forms solvent swollen microgels in organic solvents such as methanol and dioxane and in water at temperatures below 15 °C. In the second step, these PDEGAC particles were transformed to PHEAA microgels through aminolysis in dioxane with ethanolamine and a small amount of ethylenediamine. Dynamic laser scattering studies confirmed that the colloidal stability of microgels was maintained during the aminolysis in dioxane and subsequent transfer to water. Characterization of the PHEAA microgels indicated about 9 mol % of primary amino groups. These provide functionality for bioconjugation. As proof-of-concept experiments, we attached the enzyme horseradish peroxidase (HRP) to these aqueous microgels through (i) N-(3-(dimethylamino)propyl)-N'-ethylcarbodiimide hydrochloride (EDC) coupling to the carboxylated microgels or (ii) bis-aryl hydrazone (BAH) coupling to microgels functionalized with 6-hydrazinonicotinate acetone (PHEAA-HyNic). Our results showed that HRP maintained its catalytic activity after covalent attachment (87% for EDC coupling, 96% for BAH coupling). The microgel enhanced the stability of the enzyme to thermal denaturation. For example, the residual activity of the microgel-supported enzyme was 76% after 330 min of annealing at 50 °C, compared to only 20% for the free enzyme under these

  13. Syntheses of [6-14C] and [5-carboxy, 6-14C2]nitrendipine

    International Nuclear Information System (INIS)

    Maul, N.; Scherling, D.

    1989-01-01

    [6- 14 C]Nitrendipine synthesis started from barium[ 14 ]carbonate, which was converted to [1- 14 C]acetyl chloride. The acid chloride was condensed with Meldrum's acid (2,2-dimethyl-1,3-dioxane-4,6-dione). The resulting intermediate was treated with boiling methanol to give methyl [3- 14 C]acetoacetate. The reaction with gaseous ammonia in toluene yielded the corresponding methyl 3-amino[3- 14 C]crotonate which was condensed with ethyl 2-(3-nitro-benzylidene) acetoacetate to obtain [6- 14 C]nitrendipine. (author)

  14. Syntheses of (6- sup 14 C) and (5-carboxy, 6- sup 14 C sub 2 )nitrendipine

    Energy Technology Data Exchange (ETDEWEB)

    Maul, N.; Scherling, D. (Bayer AG, Wuppertal (Germany, F.R.). Inst. fuer Pharmakologie)

    1989-04-01

    (6-{sup 14}C)Nitrendipine synthesis started from barium({sup 14})carbonate, which was converted to (1-{sup 14}C)acetyl chloride. The acid chloride was condensed with Meldrum's acid (2,2-dimethyl-1,3-dioxane-4,6-dione). The resulting intermediate was treated with boiling methanol to give methyl (3-{sup 14}C)acetoacetate. The reaction with gaseous ammonia in toluene yielded the corresponding methyl 3-amino(3-{sup 14}C)crotonate which was condensed with ethyl 2-(3-nitro-benzylidene) acetoacetate to obtain (6-{sup 14}C)nitrendipine. (author).

  15. Evaluation of the ionization quenching correction for several liquid scintillators

    International Nuclear Information System (INIS)

    Los Arcos, J. M.; Borras, C.

    1990-01-01

    The most appropriate computational model for the ionization quenching function Q(E) is analyzed for electrons in liquid scintillators. A numerical evaluation of Q(E) from 0.1 keV to 3 MeV which the kB parameter varying between 0.005 and 0.010 cm/MeV is presented for seven scintillators; Toluene, Toluene-Alcohol, PCS, Toluene-CCl4, INSTAGEL, Dioxane-Naphtalene and HISAFE II. The numerical result are summarized as tables of Ieast squares fitting coefficient which make easy the computation of Q(E). (Author)

  16. Evaluation of the ionization quenching correction for several liquid scintillators

    International Nuclear Information System (INIS)

    Los Arcos, J.M.; Borras, C.

    1990-01-01

    The most appropiate computational model for the ionization quench-ing function Q(E) is analyzed for electrons in liquid scintillators. A numerical evaluation of Q(E) from 0.1 keV to 3 MeV which the kB parameter varying between 0.005 and 0.010 cm/MeV is presented for seven scintillators; Toluene, Toluene-Alcohol, PCS, Toluene-CC14, INSTAGEL, Dioxane-Naphtalene and HISAFE II. The numerical result are summarized as tables of least squares fitting coefficient which make easy the computation of Q(E).(Author)

  17. Conformational analysis of six- and twelve-membered ring compounds by molecular dynamics

    DEFF Research Database (Denmark)

    Christensen, I T; Jørgensen, Flemming Steen

    1997-01-01

    . A series of methyl-substituted 1,3-dioxanes were investigated at 1000 K, and the number of chair-chair interconversions could be quantitatively correlated to the experimentally determined ring inversion barrier. Similarly, the distribution of sampled minimum-energy conformations correlated with the energy......-derived Boltzmann distribution. The macrocyclic ring system cyclododecane was subjected to an MD simulation at 1000 K and 71 different conformations could be sampled. These conformations were compared with the results of previously reported conformational analyses using stochastic search methods, and the MD method...

  18. Radical-mediated reduction of the dithiocarbamate group under tin-free conditions.

    Science.gov (United States)

    McMaster, Claire; Bream, Robert N; Grainger, Richard S

    2012-06-28

    Reductive desulfurisation of dithiocarbamates is conveniently achieved using H(3)PO(2)-Et(3)N-ACCN in refluxing dioxane. Fused and spirocyclic β-lactams, prepared through 4-exo trig carbamoyl radical cyclisation-dithiocarbamate group transfer reactions, are reduced without fragmentation of the strained 4-membered ring. Diethyl tetraacetyl-d-glucopyranosyl dithiocarbamate is selectively reduced with or without acyloxy group migration depending on reaction conditions and choice of reductant. Deuterium incorporation from D(3)PO(2)-Et(3)N is observed for a system involving a nucleophilic radical intermediate, but not in the case of the electrophilic radical obtained through acyloxy group migration on a glucose derivative.

  19. The effect of organic water-miscible solvents on the extraction of uranium by TOA

    International Nuclear Information System (INIS)

    Shi Xiukun; Shen Xinghai; Pen Qixiu; Gao Hongchen

    1989-01-01

    The effect of organic water-miscible solvents, such as methanol, ethanol, acetone, dioxane, glycol, dimethylsulfoxide (DMSO), dimethylformamide (DMF), tetrahydrofurance (THF) in aqueous phase on the extraction of uranyl sulphate by tri-n-octylamine (TOA) has been investigated. All data obtained showed that the addition of alcohols, ketones etc. into aqueous phase brings about an increase of distribution ratio of uranium, whereas the addition of DMSO, DMF etc. brings about a decrease of distribution ratio of uranium. In the present study, the regularity and mechanism of extraction with TOA are further studied and discussed from the measurements of some physical properties, such as dielectric constant, interface tension etc

  20. Evaluation of the ionization quenching correction for several liquid scintillators; Evaluacion de la extincion por ionizacion para diversos liquidos centelleadores

    Energy Technology Data Exchange (ETDEWEB)

    Los Arcos, J M; Borras, C

    1990-07-01

    The most appropriate computational model for the ionization quenching function Q(E) is analyzed for electrons in liquid scintillators. A numerical evaluation of Q(E) from 0.1 keV to 3 MeV which the kB parameter varying between 0.005 and 0.010 cm/MeV is presented for seven scintillators; Toluene, Toluene-Alcohol, PCS, Toluene-CCl4, INSTAGEL, Dioxane-Naphtalene and HISAFE II. The numerical result are summarized as tables of Ieast squares fitting coefficient which make easy the computation of Q(E). (Author)

  1. RDT&E for Emerging Contaminants

    Science.gov (United States)

    2010-06-01

    Perchlorate ● NDMA ● 1,4-Dioxane ● PFCs 8 Perchlorate Issue ● Broad Use & Occurrence  DoD - Rocket propellant - Insensitive munitions  Pyrotechnics and...and 18O -20 -15 -10 -5.0 0.0 5.0 -30 -25 -20 -15 -10 -5 0 5 10 Laboratory Military Natural Herbicides Gunpowder Road Flares Taiwan 3 7 C l 18 O 27 NDMA ...Toxicology  NDMA is a potent mutagen, teratogen, & carcinogen.  EPA 10-6 Lifetime Cancer Risk = 0.7 ng/L.  California DHS; 10 ng/L Action

  2. Hydrogen transfer reduction of polyketones catalyzed by iridium complexes: a novel route towards more biocompatible materials.

    Science.gov (United States)

    Milani, Barbara; Crottib, Corrado; Farnetti, Erica

    2008-09-14

    Transfer hydrogenation from 2-propanol to CO/4-methylstyrene and CO/styrene polyketones was catalyzed by [Ir(diene)(N-N)X] (N-N = nitrogen chelating ligand; X = halogen) in the presence of a basic cocatalyst. The reactions were performed using dioxane as cosolvent, in order to overcome problems due to low polyketone solubility. The polyalcohols were obtained in yields up to 95%, the conversions being markedly dependent on the nature of the ligands coordinated to iridium as well as on the experimental conditions.

  3. Desenvolvimento de um método de MEFS com CG-DIC para determinação de 1,4 dioxana em amostras de cosméticos

    Directory of Open Access Journals (Sweden)

    Silva Fernando C.

    2001-01-01

    Full Text Available A headspace solid-phase microextraction (HS-SPME for the determination of 1,4 dioxane in cosmetics by gas chromatography is described. A manual SPME holder with 85 µm polyacrylate coating is utilized. The method is determined to have good resolution, satisfactory linerity (correlation coefficient r=0.997 for 0.20-10.00 mg Kg-1 range, a relative standard deviation of 6.3% and a detection limit of 5.00 µg Kg-1. Some cosmectic products were analyzed.

  4. Synthesis and characterization of novel organotin carboxylate maleimide monomers and copolymers

    Directory of Open Access Journals (Sweden)

    2009-06-01

    Full Text Available Two novel tributyltin carboxylate maleimide monomers, tributyltin(maleimidoacetate and tributyltin(4-maleimidobenzoate, were synthesized by condensation reaction of maleimidoacetic acid or 4-maleimidobenzoic acid with bis(tributyltin oxide. Copolymerization of these monomers with styrene was carried in dioxane at 70°C using asobisisobutyronitrile as free radical initiator. The structures of monomers and copolymers were confirmed by FT-IR (Fourier Transform Infrared, 1H and 13C NMR (nuclear magnetic resonance spectroscopy and elemental analysis. The copolymers were characterized by solubility and thermal analysis.

  5. Effect of organic solvents on desorption and atomic absorption determination of heavy metal ions after ion exchange concentration

    International Nuclear Information System (INIS)

    Pilipenko, A.T.; Safronova, V.G.; Zakrevskaya, L.V.

    1986-01-01

    The effect of organic solvents (acetone, methylethylketone, dioxane, ethanol) on desorption of Cu, Mn, Co, Cd, Zn, Pb, Ni from cationite KU-23 ion exchange resin and on the detection limits of their atomic absorption determination has been examined. Cobalt and cadmium can be separated quantitatively using desorption by a mixture of HCl and acetone. Addition of an organic solvent results in a higher absorbance, mainly due to a high rate and efficiency of atomization. Acetone has proved to be the best solvent: addition of 60 vol. % of this solvent to the concentrate provides 2 times lower detection limits for the heavy metas in water

  6. One-pot synthesis of 4′-alkyl-4-cyanobiaryls on the basis of the terephthalonitrile dianion and neutral aromatic nitrile cross-coupling

    Directory of Open Access Journals (Sweden)

    Roman Yu. Peshkov

    2016-07-01

    Full Text Available A convenient one-pot approach to alkylcyanobiaryls is described. The method is based on biaryl cross-coupling between the sodium salt of the terephthalonitrile dianion and a neutral aromatic nitrile in liquid ammonia, and successive alkylation of the long-lived anionic intermediate with alkyl bromides. The reaction is compatible with benzonitriles that contain methyl, methoxy and phenyl groups, fluorine atoms, and a 1-cyanonaphthalene residue. The variety of ω-substituted alkyl bromides, including an extra bromine atom, a double bond, cyano and ester groups, as well as a 1,3-dioxane fragment are suitable as alkylation reagents.

  7. Preparatory on manganose salts of carboxilic acids labelled with 54Mn and comparison with 54MnCl2 in liquid scintillation counting

    International Nuclear Information System (INIS)

    Rodriguez, L.; Los Arcos, J.M.; Grau, A.

    1992-01-01

    Procedures for scintillation sample preparation of manganose dimethylbutirate, decanoate and palmitate, labelled with 54 Mn are described. Their quenching effect, spectral evolution and counting stability along several weeks are analysed in liquid scintillation measurements with Toluene, HlSafe II, PCS, Instagel, Dioxane-naphtalene and Toluene-alcohol. For comparison, inorganic 54 MnCl 2 samples are also studied, resulting in acceptable counting stability but showing greater quenching and signs of little spectral degradation against the organic samples. (author) 14 fig. 15 ref

  8. Construção de um calorímetro isotérmico diferencial de alta sensibilidade e baixo custo Construction of a differential isothermal calorimeter of high sensitivity and low cost

    Directory of Open Access Journals (Sweden)

    Rafael Bergamo Trinca

    2009-01-01

    Full Text Available The high cost of sensitivity commercial calorimeters may represent an obstacle for many calorimetric research groups. This work describes the construction and calibration of a batch differential heat conduction calorimeter with sample cells volumes of about 400 μL. The calorimeter was built using two small high sensibility square Peltier thermoelectric sensors and the total cost was estimated to be about US$ 500. The calorimeter was used to study the excess enthalpy of solution of binary mixtures of liquids, as a function of composition, for the following binary systems of solvents: water + 1,4-dioxane or + dimethylsulfoxide at 298,2 ± 0,5 K.

  9. Recent progress in electron scattering from atoms and molecules

    Energy Technology Data Exchange (ETDEWEB)

    Brunger, M. J. [Centre for Antimatter-Matter Studies, CAPS, Flinders University, GPO Box 2100, Adelaide, SA 5001, Australia and Institute of Mathematical Sciences, University of Malaya, Kuala Lumpur (Malaysia); Buckman, S. J. [Institute of Mathematical Sciences, University of Malaya, Kuala Lumpur, Malaysia and Centre for Antimatter-Matter Studies, AMPL, Australian National University, Canberra, ACT 0200 (Australia); Sullivan, J. P.; Palihawadana, P. [Centre for Antimatter-Matter Studies, AMPL, Australian National University, Canberra, ACT 0200 (Australia); Jones, D. B. [School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Chiari, L.; Pettifer, Z. [Centre for Antimatter-Matter Studies, CAPS, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Silva, G. B. da [Centre for Antimatter-Matter Studies, CAPS, Flinders University, GPO Box 2100, Adelaide, SA 5001, Australia and Universidade Federal de Mato Grosso, Barra do Garças, Mato Grosso (Brazil); Lopes, M. C. A. [Centre for Antimatter-Matter Studies, CAPS, Flinders University, GPO Box 2100, Adelaide, SA 5001, Australia and Departamento de Fisica, Universidade Federal de Juiz de Fora, Juiz de Fora, MG (Brazil); Duque, H. V. [Departamento de Fisica, Universidade Federal de Juiz de Fora, Juiz de Fora, MG (Brazil); Masin, Z.; Gorfinkiel, J. D. [Department of Physical Sciences, The Open University, Walton Hall, Milton Keynes, MK7 6AA (United Kingdom); Garcia, G. [Instituto de Fisica Fundamental, CSIC, Madrid E-28006 (Spain); Hoshino, M.; Tanaka, H. [Department of Physics, Sophia University, Tokyo, 102-8554 (Japan); Limão-Vieira, P. [Laboratório de Colisões Atómicas e Moleculares, CEFITEC, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal)

    2014-03-05

    We present and discuss recent results, both experimental and theoretical (where possible), for electron impact excitation of the 3s[3/2 ]{sub 1} and 3s′[1/2 ]{sub 1} electronic states in neon, elastic electron scattering from the structurally similar molecules benzene, pyrazine, and 1,4-dioxane and excitation of the electronic states of the important bio-molecule analogue α-tetrahydrofurfuryl alcohol. While comparison between theoretical and experimental results suggests that benchmarked cross sections for electron scattering from atoms is feasible in the near-term, significant further theoretical development for electron-molecule collisions, particularly in respect to discrete excitation processes, is still required.

  10. Neutral complexes of the indium dihalides

    Energy Technology Data Exchange (ETDEWEB)

    Sinclair, I.; Worrall, I.J. (Lancaster Univ. (UK))

    1982-03-15

    The neutral complexes In/sub 2/X/sub 4/.2L (X=Cl, Br, I; L 1,4-dioxan, tetrahydropyran, tetrahydrofuran, tetrahydrothiophene), In/sub 2/X/sub 4/.2L (X=Br, I; Ldimethylsulphide), In/sub 2/X/sub 4/.4L (X=Cl, Br, I; Lpiperidine, piperazine, morpholine), and In/sub 2/X/sub 4/.4L (X=Br, I; L=pyridine, dimethylsulphoxide) have been prepared. Solid state Raman spectra indicate that the compounds contain indium-indium bonds.

  11. Molecular determinants for drug-receptor interactions. Part 2. An ab initio molecular orbital and dipole moment study of the novel nootropic agent piracetam (2-oxopyrrolidin-1-ylacetamide)

    Science.gov (United States)

    Lumbroso, H.; Liégeois, C.; Pappalardo, G. C.; Grassi, A.

    From the ab initio molecular energies of the possible conformers and from a classical dipole moment analysis of 2-oxopyrrolidin-l-ylacetamide (μ = 4.02 D in dioxan at 30.0°C), the preferred conformation in solution of this novel nootropic agent has been determined. The exocyclic N-CH 2 bond is rotated in one sense by 90° and the exocyclic CH 2-C bond rotated in the same sense by 120° from the "planar" ( OO)- cis conformation. The structures of the two enantiomers in solution differ from that of the crystalline molecule.

  12. Caracterização de membranas assimétricas de acetato de celulose produzidas a partir do aproveitamento do resíduo da palha de milho para uso em ultrafiltração

    Directory of Open Access Journals (Sweden)

    Elaine Angélica Mundim Ribeiro

    2014-06-01

    Full Text Available Cellulose acetates (CA with different degrees of acetylation were synthesized from cellulose extracted from corn stover. Membranes were prepared for the ultrafiltration process with pure polymers and blend form of CA utilizing a dioxane/acetone system. The membranes were characterized according to their transport properties. The blend form materials presented the best results for application in ultrafiltration experiments. M-TAC/DAC (corn stover triacetate and diacetate and M-TAC/DAC-Rho (corn stover triacetate and Rhodia diacetate presented rejection to egg albumin protein of 87.39% and 80.50%, respectively. Thus, MWCO of 45 kDa was determined for these materials.

  13. Potentiometric study of Nd3+ chelates of substituted salicylhydroxamic acids

    International Nuclear Information System (INIS)

    Deshpande, R.G.; Jahagirdar, D.V.

    1976-01-01

    The interaction of Nd 3+ ion with salicylhydroxamic acid and 5-methyl, 5-chloro, 5-bromo, 5-nitro, 4-chloro, 4-bromo and 3-chloro salicylhydroxamic acids is investigated potentiometrically by Calvin-Bjerrum titration technique at 30 0 +- 0.1 0 and ionic strength μ=0.1 M(NaClO 4 ) in 50% v/v dioxane-water mixtures. Nd 3+ forms only 1:1 chelates with these ligands. The validity of the log K= apk + b relationship is examined for these chelates. (author)

  14. Stability Constants of Some Biologically Important Pyrazoles and Their Ni2+ Complexes in Different Dielectric Constant of Medium

    Directory of Open Access Journals (Sweden)

    S. D. Deosarkar

    2012-01-01

    Full Text Available The proton-ligand stability constants of some biologically important new pyrazoles and formation constants of their complexes with Ni(II were determined at 0.1 mol dm-3 ionic strength and at 303.15 K in different dielectric constant of dioxane-water mixture by potentiometric method. The Calvin-Bjerrum's pH-titration technique as used by Irving and Rossotti was used for determination of stability constants. The results enabled to study the electrostatic forces of attraction between metal ion and ligand with changes in dielectric constant of the medium.

  15. Lupane, friedelane, oleanane, and ursane triterpenes from the stem of Siphonodon celastrineus Griff.

    Science.gov (United States)

    Kaweetripob, Wirongrong; Mahidol, Chulabhorn; Prawat, Hunsa; Ruchirawat, Somsak

    2013-12-01

    Twenty-one triterpenes consisting of a lupane derivative, two friedelanes, an oleanane derivative, and 17 ursane-type triterpenoids, together with three known triterpenes, three sterols, a fatty acid, a sesquiterpene alkaloid, and a glycerol derivative, were isolated from the stem of Siphonodon celastrineus. Their structures were characterized by various spectroscopic techniques, as well as comparison with literature data. Twenty-seven metabolites of these were evaluated for cytotoxic activity against six human cancer cell lines. The biosynthetic formation of a 1,4-dioxane bridge is also discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Visible-Light-Promoted Metal-Free Aerobic Oxidation of Primary Amines to Acids and Lactones.

    Science.gov (United States)

    Cheng, Xiaokai; Yang, Bo; Hu, Xingen; Xu, Qing; Lu, Zhan

    2016-12-05

    A unique metal-free aerobic oxidation of primary amines via visible light photocatalytic double carbon-carbon bonds cleavage and multi carbon-hydrogen bonds oxidation was observed. Aerobic oxidation of primary amines could be controlled to afford acids by using dioxane with 18 W CFL, and lactones by using DMF with 8 W green LEDs, respectively. A plausible mechanism was proposed based on control experiments. This observation showed direct evidences for the fragmentation in the aerobic oxidation of aliphatic primary amines. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Dynamic structurization in solutions of hydrodynamically active polymers

    International Nuclear Information System (INIS)

    Pogrebnyak, V.G.; Tverdokhleb, S.V.; Naumchuk, N.V.

    1993-01-01

    The processes of ordering and self-regulation in nonlinear systems have attracted great attention because understanding the principles of self-regulation and its thermodynamics can become a clue to many physical phenomena. In this work, it is experimentally established that, under the condition of elongational flows, dynamic structurization and periodic processes may originate in the solutions of flexible, hydrodynamically-active polymers due to self-regulation in these systems. The hydrodynamic elongational field was created using the flow of a Newtonian liquid (water, acetone, dioxane) converging to a small opening. The hydrodynamically-active polymers were polyethylene oxide or hydrolyzed polyacrylamide

  18. Morphology-tunable and photoresponsive properties in a self-assembled two-component gel system.

    Science.gov (United States)

    Zhou, Yifeng; Xu, Miao; Yi, Tao; Xiao, Shuzhang; Zhou, Zhiguo; Li, Fuyou; Huang, Chunhui

    2007-01-02

    Photoresponsive C3-symmetrical trisurea self-assembling building blocks containing three azobenzene groups (LC10 and LC4) at the rim were designed and synthesized. By introducing a trisamide gelator (G18), which can self-aggregate through hydrogen bonds of acylamino moieties to form a fibrous network, the mixture of LC10 (or LC4) and G18 forms an organogel with coral-like supramolecular structure from 1,4-dioxane. The cooperation of hydrogen bonding and the hydrophobic diversity between these components are the main contributions to the specific superstructure. The two-component gel exhibits reversible photoisomerization from trans to cis transition without breakage of the gel state.

  19. Effect of mineral acid on polymer produced during radiation-induced grafting of styrene monomer

    International Nuclear Information System (INIS)

    Garnett, J.L.; Jankiewicz, S.V.; Sangster, D.F.

    1982-01-01

    The inclusion of mineral acid in a solution of styrene in methanol subjected to 60 Co γ irradiation markedly enhances the yield of monomer grafted to cellulose and other radiation grafting systems. Results were reported from a preliminary investigation into the mechanism of this acid effect through a study of the action of acid during the solution polymerization process. It was found that the presence of acid in a monomer solution such as styrene in 1, 4-dioxan led to an enhancement in the homopolymer yield of styrene; and it was showed that the acid also effected the number-average molecular weight of this homopolymer. 1 figure, 4 tables

  20. STUDY OF EPOXIDE DECYCLISATION OF CARYOPHYLENE OXIDE WITH SYNTHETIC ZEOLITE AS CATALYSTS

    Directory of Open Access Journals (Sweden)

    Winarto Haryadi

    2010-06-01

    Full Text Available The reaction of epoxide ring opening of caryophillene oxide has been done using zeolite H-Y, H-sodalit, and H-ZSM-5 as catalysts. The reactions were done in two types, there were in dioxane solvent at temperature of 110 oC and without solvent at temperature of 175 oC. The catalyst weight was 10 % from caryophillene oxide weight, and the time of reaction was four hours. The product of reaction was analyzed using GC, FTIR, and GC-MS. The reactions of caryophillene oxide in dioxane solvent with the three kinds of zeolites did not give any targeted product. Whereas, the reactions without solvent gave three main products, there was one compound with one group of secondary hidroxyl (secondary alcohol, and two compounds of ketone from caryophillene. The reaction product of caryophillene oxide obtained without using solvent with the three type of catalysts were then compared. Conversion of three main products produced by H-ZSM-5 catalyst, H-sodalit catalyst and H-Y catalyst were 82.11 %, 54.92 % and 38.53 % respectively. For that reason, the transformation of caryophillene oxide using H-ZSM-5 catalyst was considered to be the best selective product. The alcohol product was resulted from reaction between caryophillene oxide and Bronsted acid, and  the ketone products was resulted from the reaction with Lewis acid in zeolite.   Keywords: Epoxide ring opening, HY, H-sodalit and HZSM-5

  1. Characteristics of Lignin Fractions from Dilute Acid Pretreated Switchgrass and Their Effect on Cellobiohydrolase from Trichoderma longibrachiatum

    Directory of Open Access Journals (Sweden)

    Lan Yao

    2018-02-01

    Full Text Available To investigate the interactions between acid pretreated switchgrass lignin and cellobiohydrolase (CBH, three different lignin fractions were isolated from dilute acid pretreated switchgrass by (i ethanol extraction, followed by (ii dioxane/H2O extraction, and (iii cellulase treatment, respectively. Structural properties of each lignin fraction were elucidated by GPC, 13C-NMR, and 2D-HSQC NMR analyses. The adsorptions of CBH to the isolated lignin fractions were also studied by Langmuir adsorption isotherms. Ethanol-extractable lignin fraction, mainly composed of syringyl (S and guaiacyl (G units, had the lowest molecular weight, while dioxane/H2O-extracted lignin fraction had the lowest S/G ratio with higher content of p-coumaric acid (pCA unit. The residual lignin fraction after enzymatic treatment had the highest S/G ratio without hydroxyphenyl (H unit. Strong associations were found between lignin properties such as lignin composition and S/G ratio and its non-productive enzyme adsorption factors including the maximum adsorption capacity and binding strength.

  2. Emerging Water Contaminants: Technical, Legal and Policy Challenges

    Science.gov (United States)

    Deeb, R. A.; Kresic, N.; Laugier, M. C.; Kavanaugh, M. C.

    2002-12-01

    Approximately 120 new chemicals are created each year due to ever-improving industry and technology markets. Releases of new contaminants into the environment can occur during production, use and disposal of these chemicals thereby leading to potential contamination of water supply sources. Very few emerging contaminants are regulated. In addition, knowledge gaps regarding emerging contaminants include lack health effects, occurrence (either because these compounds are not measured or because concentrations are below detection limits of readily available analytical techniques) and fate and transport in the environment especially with regards to mobility and persistence. The sources of these compounds are numerous. One source is treated wastewater, which is re-injected into groundwater aquifers for indirect potable reuse purposes. Emerging compounds of concern can be classified in various classes. This presentation will focus on contaminants, which have emerged in the last 10 years including pharmaceuticals (antibiotics/drugs), personal care products (polycyclic musks), pesticides/herbicides, industrial solvents (1,4-dioxane), gasoline additives (MTBE), disinfection byproducts such as NDMA (N-nitrosodimethylamine), and inorganic compounds such as perchlorate and arsenic. This presentation will present technical, legal and legislative challenges posed by the presence of these contaminants in water. Background information including chemical's history of use, sources in the environments, nationwide occurrence, physical and chemical properties, behavior in the environment and technologies for removal from soil and water will be presented. In addition, case studies on MTBE, pharmaceuticals and personal care products, 1,4-dioxane, arsenic and NDMA will be discussed.

  3. Viscosity of binary mixtures of 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid with four organic solvents

    International Nuclear Information System (INIS)

    Ciocirlan, Oana; Croitoru, Oana; Iulian, Olga

    2016-01-01

    Highlights: • Viscosities of four binary mixtures of [Emim][BF4] with organic solvents. • Viscosity models based on Eyring’s theory. • Excess functions calculated. • Data for binaries new in the literature, except for system with DMSO. - Abstract: This paper reports experimental values of dynamic viscosity for four binary systems of 1-ethyl-3-methylimidazolium tetrafluoroborate, [Emim][BF4], with dimethyl sulfoxide (DMSO), acetonitrile (ACN), ethylene glycol (EG) and 1,4-dioxane over the temperature ranges from 293.15 K to 353.15 K at p = 0.1 MPa. All binary mixtures were completely miscible over the entire range of mole fraction, except the system with 1,4-dioxane. The viscosity results have been correlated by the one parameter Grunberg–Nissan and Fang and He equations and the two-parameter McAllister, Eyring-UNIQUAC, Eyring-NRTL and Eyring-Wilson models and the results were compared. Additionally, the viscosity deviations, Δη, and the excess Gibbs energy of activation for viscous flow, G"∗"E, were calculated and fitted to the Redlich–Kister equation. The results show that all Δη values are negative over the whole composition range and the G"∗"E values are positive, except for the system with EG. The results of the excess functions are discussed in terms of molecular interactions.

  4. Removal of phosphate using copper-loaded polymeric ligand exchanger prepared by radiation grafting of polypropylene/polyethylene (PP/PE) nonwoven fabric

    Science.gov (United States)

    Barsbay, Murat; Kavaklı, Pınar Akkaş; Güven, Olgun

    2010-03-01

    A novel polymeric ligand exchanger (PLE) was prepared for the removal of phosphate ions from water. 2,2'-dipyridylamine (DPA), a bidentate ligand forming compound with high coordination capacity with a variety of metal ions was bound to glycidyl methacrylate (GMA) grafted polypropylene/polyethylene (PP/PE) nonwoven fabric synthesized by radiation-induced grafting technique. DPA attachment on epoxy ring of GMA units was tested in different solvents, i.e. methanol, ethanol, dioxane and dimethylsulfoxide (DMSO). The highest amount of modification was achieved in dioxane. In order to prepare the corresponding PLE for the removal of phosphate, DPA-immobilized fabric was loaded with Cu(II) ions. Phosphate adsorption experiments were performed in batch mode at different pH (5-9) and phosphate concentrations. The fabric was found to be effective for the removal of phosphate ions. At every stage of preparation and use, the nonwoven fabric was characterized by thermal (i.e. DSC and TGA) and spectroscopic (FTIR) methods. Competitive adsorption experiments were also carried out using two solutions with different concentration levels at pH 7 to see the effect of competing ions. Phosphate adsorption was found to be effective and selective from solutions having trace amounts of competitive anions. It is expected that the novel PLE synthesized can be used for the removal of phosphate ions in low concentrations over a large range of pH.

  5. Polymer Vesicles as Robust Scaffolds for the Directed Assembly of Highly Crystalline Nanocrystals †

    KAUST Repository

    Wang, Mingfeng

    2009-12-15

    We report the incorporation of various inorganic nanoparticles (NPs) (PbS, LaOF, LaF3, and TiO2, each capped by oleic acid, and CdSe/ZnS core/shell QDs capped by trioctylphosphine oxide) into vesicles (d = 70-150 nm) formed by a sample of poly(styrene-b-acrylic acid) (PS4o4-b-PAA 62, where the subscripts refer to the degree of polymerization) in mixtures of tetrahydrofuran (THF), dioxane, and water. The block copolymer formed mixtures of crew-cut micelles and vesicles with some enhancement of the vesicle population when the NPs were present. The vesicle fraction could be isolated by selective sedimentation via centrifugation, followed by redispersion in water. The NPs appeared to be incorporated into the PAA layers on the internal and external walls of the vesicles (strongly favoring the former). NPs on the exterior surface of the vesicles could be removed completely by treating the samples with a solution of ethylenediaminetetraacetate (EDTA) in water. The triangular nanoplatelets of LaF3 behaved differently. Stacks of these platelets were incorporated into solid colloidal entities, similar in size to the empty vesicles that accompanied them, during the coassembly as water was added to the polymer/LaF3/THF/ dioxane mixture. © 2009 American Chemical Society.

  6. Evaluation of Stability of Complexes of Inner Transition Metal Ions with 2-Oxo-1-pyrrolidine Acetamide and Role of Systematic Errors

    Directory of Open Access Journals (Sweden)

    Sangita Sharma

    2011-01-01

    Full Text Available BEST FIT models were used to study the complexation of inner transition metal ions like Y(III, La(III, Ce(III, Pr(III, Nd(III, Sm(III, Gd(III, Dy(III and Th(IV with 2-oxo-1-pyrrolidine acetamide at 30 °C in 10%, 20, 30, 40, 50% and 60% v/v dioxane-water mixture at 0.2 M ionic strength. Irving Rossotti titration method was used to get titration data. Calculations were carried out with PKAS and BEST Fortran IV computer programs. The expected species like L, LH+, ML, ML2 and ML(OH3, were obtained with SPEPLOT. Stability of complexes has increased with increasing the dioxane content. The observed change in stability can be explained on the basis of electrostatic effects, non electrostatic effects, solvating power of solvent mixture, interaction between ions and interaction of ions with solvents. Effect of systematic errors like effect of dissolved carbon dioxide, concentration of alkali, concentration of acid, concentration of ligand and concentration of metal have also been explained here.

  7. Synthesis and antibacterial activity of some Schiff bases derived from 4-aminobenzoic acid

    Directory of Open Access Journals (Sweden)

    JIGNA PAREKH

    2005-10-01

    Full Text Available The following Schiff bases have been synthesized: (1 4-[(2-chlorobenzylidene amino]benzoic acid [JP1], (2 4-[(furan-2-ylmethyleneamino]benzoic acid [JP2], (3 4-[(3-phenylallylideneamino]benzoic acid [JP3], (4 4-[(2-hydroxybenzylidene amino]benzoic acid [JP4], (5 4-[(4-hydroxy-3-methoxybenzylideneamino]benzoic acid [JP5] and (6 4-[(3-nitrobenzylideneamino]benzoic acid [JP6]. They were screened as potential antibacterial agents against a number of medically important bacterial strains. The antibacterial activity was studied against A. faecalis ATCC 8750, E. aerogenes ATCC 13048, E. coli ATCC 25922, K. pneumoniae NCIM 2719, S. aureus ATCC 25923, P. vulgaris NCIM 8313, P. aeruginosa ATCC 27853 and S. typhimurium ATCC 23564. The antibacterial activity was evaluated using the Agar Ditch method. The solvents used were 1,4-dioxane and dimethyl sulfoxide. Different effects of the compounds were found in the bacterial strains investigated and the solvents used, suggesting, once again, that the antibacterial activity is dependent on the molecular structure of the compound, the solvent used and the bacterial strain under consideration. In the present work, 1,4-dioxane proved to be a good solvent in inhibiting the above stated bacterial strains.

  8. Amperometric biosensor for the detection of hydrogen peroxide using catalase modified electrodes in polyacrylamide.

    Science.gov (United States)

    Varma, Shailly; Mattiasson, Bo

    2005-09-23

    A simple biosensor for the detection of hydrogen peroxide in organic solvents has been developed and coupled to a flow injection analysis (FIA) system. Catalase was entrapped in polyacrylamide gel and placed on the surface of platinum (working electrode) fixed in a Teflon holder with Ag-wire (auxiliary electrode), followed by addition of filter paper soaked in KCl. The entrapped catalase gel was held on the electrode using membranes. The effects of cellulose and polytetrafluroethylene (PTFE) membranes on the electrode response towards hydrogen peroxide have been studied. The modified electrode has been used to study the detection of hydrogen peroxide in solvents like water, dimethyl sulfoxide (DMSO), and 1,4-dioxane using amperometric techniques like cyclic voltammetry (CV) and FIA. The CV of modified catalase electrode showed a broad oxidation peak at -150 mV and a clear reduction peak at -212 mV in the presence of hydrogen peroxide. Comparison of CV with hydrogen peroxide in various solvents has been carried out. The electrode showed an irreversible kinetics with DMSO as the solvent. A flow cell has been designed in order to carry on FIA studies to obtain calibration plots for hydrogen peroxide with the modified electrode. The calibration plots in several solvents such as water, dimethyl sulfoxide, 1,4-dioxane have been obtained. The throughput of the enzyme electrode was 10 injections per hour. Due to the presence of membrane the response time of the electrode is concentration dependent.

  9. Comparison of the acetyl bromide spectrophotometric method with other analytical lignin methods for determining lignin concentration in forage samples.

    Science.gov (United States)

    Fukushima, Romualdo S; Hatfield, Ronald D

    2004-06-16

    Present analytical methods to quantify lignin in herbaceous plants are not totally satisfactory. A spectrophotometric method, acetyl bromide soluble lignin (ABSL), has been employed to determine lignin concentration in a range of plant materials. In this work, lignin extracted with acidic dioxane was used to develop standard curves and to calculate the derived linear regression equation (slope equals absorptivity value or extinction coefficient) for determining the lignin concentration of respective cell wall samples. This procedure yielded lignin values that were different from those obtained with Klason lignin, acid detergent acid insoluble lignin, or permanganate lignin procedures. Correlations with in vitro dry matter or cell wall digestibility of samples were highest with data from the spectrophotometric technique. The ABSL method employing as standard lignin extracted with acidic dioxane has the potential to be employed as an analytical method to determine lignin concentration in a range of forage materials. It may be useful in developing a quick and easy method to predict in vitro digestibility on the basis of the total lignin content of a sample.

  10. Secondary deuterium isotope effects in the hydrolysis of some acetals

    International Nuclear Information System (INIS)

    Paterson, R.V.

    Secondary α-deuterium kinetic isotope effects have been determined in the hydrolyses of some acetals. Benzaldehyde dimethyl acetal and 2-phenyl-1,3-dioxolan show isotope effects in agreement with an A1 mechanism. 2-Phenyl-4,4,5,5-tetramethyl-1,3-dioxolan, which has been shown to undergo hydrolysis by an A2 type mechanism, has an isotope effect in agreement with participation by water in the transition state. Hydrolysis of benzylidene norbornanediols, although complicated by isomerisation, has an isotope effect in agreement with an A2 mechanism. Kinetic isotope effects in acetals which have a neighbouring carboxyl group have also been determined. Hydrolysis of 2-carboxybenzaldehyde dimethyl acetal in aqueous and 82% w/w dioxan-water buffers has isotope effects in agreement with a large degree of carbonium ion character in the transition state. Anderson and Capon proposed nucleophilic participation in the hydrolysis of this acetal in 82% dioxan-water. The isotope effect determined in this study is not in agreement with this finding. Hydrolysis of 2-(2'-carboxyphenyl)-4,4,5,5-tetramethyl-1,3-dioxolan shows an isotope effect larger than the corresponding dioxolan without the carboxyl group in agreement with some carbonium ion character in the transition state. A new synthesis of a deuterated aldehyde is described which might be general for aldehydes which will not form benzoins readily. (author)

  11. In-liquid Plasma. A stable light source for advanced oxidation processes in environmental remediation

    Science.gov (United States)

    Tsuchida, Akihiro; Shimamura, Takeshi; Sawada, Seiya; Sato, Susumu; Serpone, Nick; Horikoshi, Satoshi

    2018-06-01

    A microwave-inspired device that generates stable in-liquid plasma (LP) in aqueous media and emits narrow light emission lines at 280-320 nm, 660 nm and 780 nm is examined as a light source capable of driving photochemical reactions and advanced oxidation processes in wastewater treatments. The microwave-driven lighting efficiency was improved by decompressing the inside of the reaction vessel, which resulted in lowering the incident power of the microwaves and suppressed the deterioration of the microwave irradiation antenna. This protocol made it possible to generate continuous stable plasma in water. Evaluation of the LP device was carried out by revisiting the decomposition of 1,4-dioxane in aqueous media against the use of such other conventional water treatment processes as (i) UV irradiation alone, (ii) TiO2-assisted photocatalysis with UV irradiation (UV/TiO2), (iii) oxidation with sodium hypochlorite (NaClO), and (iv) UV-assisted decomposition in the presence of NaClO (UV/NaClO). The in-liquid plasma technique proved superior to these four other methods. The influence of pH on the LP protocol was ascertained through experiments in acidified (HCl and H2SO4) and alkaline (NaOH and KOH) aqueous media. Except for H2SO4, decomposition of 1,4-dioxane was enhanced in both acidic and alkaline media.

  12. Quantitative determination of deoxyribonucleic acid in rat brain

    Science.gov (United States)

    Penn, N. W.; Suwalski, R.

    1969-01-01

    1. A procedure is given for spectrophotometric analysis of rat brain DNA after its resolution into component bases. Amounts of tissue in the range 50–100mg. can be used. 2. The amount of DNA obtained by the present method is 80% greater than that reported for rat brain by a previous procedure specific for DNA thymine. Identity of the material is established by the base ratios of purines and pyrimidines. The features responsible for the higher yield are the presence of dioxan during alkaline hydrolysis of tissue, the determination of the optimum concentration of potassium hydroxide in this step and omission of organic washes of the initial acid-precipitated residues. 3. The requirement for dioxan during alkaline hydrolysis suggests a possible association of brain DNA with lipid. The concentration of potassium hydroxide that gives maximum yield is 0·1m, indicating that there may be internucleotide linkages in this DNA that are more sensitive to alkali than those of liver or thymus DNA. 4. This procedure gives low yields of DNA from liver. It is not suitable for analysis of the DNA from this tissue. PMID:5353529

  13. Halogen-bonded network of trinuclear copper(II 4-iodopyrazolate complexes formed by mutual breakdown of chloroform and nanojars

    Directory of Open Access Journals (Sweden)

    Stuart A. Surmann

    2016-11-01

    Full Text Available Crystals of bis(tetrabutylammonium di-μ3-chlorido-tris(μ2-4-iodopyrazolato-κ2N:N′tris[chloridocuprate(II] 1,4-dioxane hemisolvate, (C16H36N2[Cu3(C3H2IN23Cl5]·0.5C4H8O or (Bu4N2[CuII3(μ3-Cl2(μ-4-I-pz3Cl3]·0.5C4H8O, were obtained by evaporating a solution of (Bu4N2[{CuII(μ-OH(μ-4-I-pz}nCO3] (n = 27–31 nanojars in chloroform/1,4-dioxane. The decomposition of chloroform in the presence of oxygen and moisture provides HCl, which leads to the breakdown of nanojars to the title trinuclear copper(II pyrazolate complex, and possibly CuII ions and free 4-iodopyrazole. CuII ions, in turn, act as catalyst for the accelerated decomposition of chloroform, ultimately leading to the complete breakdown of nanojars. The crystal structure presented here provides the first structural description of a trinuclear copper(II pyrazolate complex with iodine-substituted pyrazoles. In contrast to related trinuclear complexes based on differently substituted 4-R-pyrazoles (R = H, Cl, Br, Me, the [Cu3(μ-4-I-pz3Cl3] core in the title complex is nearly planar. This difference is likely a result of the presence of the iodine substituent, which provides a unique, novel feature in copper pyrazolate chemistry. Thus, the iodine atoms form halogen bonds with the terminal chlorido ligands of the surrounding complexes [mean length of I...Cl contacts = 3.48 (1 Å], leading to an extended two-dimensional, halogen-bonded network along (-110. The cavities within this framework are filled by centrosymmetric 1,4-dioxane solvent molecules, which create further bridges via C—H...Cl hydrogen bonds with terminal chlorido ligands of the trinuclear complex not involved in halogen bonding.

  14. Advanced oxidation of five contaminants in water by UV/TiO2: Reaction kinetics and byproducts identification.

    Science.gov (United States)

    Alvarez-Corena, Jose R; Bergendahl, John A; Hart, Fred L

    2016-10-01

    The extent and kinetics of degradation of 1,4 dioxane, n-nitrosodimethylamine (NDMA), tris-2-chloroethyl phosphate (TCEP), gemfibrozil, and 17β estradiol in a prepared aqueous matrix by means of UV/TiO2 (ultraviolet light/titanium dioxide) oxidation was evaluated. Degussa P25 TiO2 was employed as a photocatalyst excited by UV light in a 1 L water-jacketed batch photoreactor. The rate of degradation was modeled using a pseudo-first order rate model and the Langmuir-Hinshelwood rate model with a high correlation. Degradation rate constants were found to be maximum at pH 5.0 and 1.5 g L(-)(1) TiO2 dose. For these conditions first order rate constants, values were as follows: 0.29 min(-1) for 1,4 dioxane, 0.50 min(-1) for NDMA, 0.12 min(-1) for TCEP, 0.61 min(-1) for gemfibrozil, and 0.53 min(-1) for 17β estradiol. While for the Langmuir-Hinshelwood rate model, the following constants were found: 0.11 Lmg(-1) and 2.81 mgL(-1) min(-1) for 1,4 dioxane, 0.12 Lmg(-1) and 4.35 mgL(-1) min(-1) for NDMA, 0.06 Lmg(-1) and 1.79 mgL(-1) min(-1) for TCEP, 0.21 Lmg(-1) and 3.27 mgL(-1) min(-1) for gemfibrozil, and 0.15 Lmg(-1) and 3.43 mgL(-1) min(-1) for 17β estradiol. In addition, specific byproducts of degradation were identified using GC/MS analysis. The results obtained from the kinetics analysis showed that UV/TiO2 oxidation is a promising process for treating trace organic contaminants in water, but further research is needed to better understand how to incorporate these findings into pilot and full-scale designs. The toxicity of oxidation byproducts, and their potential for interacting with other compounds should be considered in the treatment of contaminated waters using the UV/TiO2 oxidation process. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Synthesis, crystal structure, vibrational spectra and theoretical calculations of quantum chemistry of a potential antimicrobial Meldrum's acid derivative

    Science.gov (United States)

    Campelo, M. J. M.; Freire, P. T. C.; Mendes Filho, J.; de Toledo, T. A.; Teixeira, A. M. R.; da Silva, L. E.; Bento, R. R. F.; Faria, J. L. B.; Pizani, P. S.; Gusmão, G. O. M.; Coutinho, H. D. M.; Oliveira, M. T. A.

    2017-10-01

    A new derivative of Meldrum's acid 5-((5-chloropyridin-2-ylamino)methylene)-2,2-dimethyl-1,3-dioxane-4,6-dione (CYMM) of molecular formula C12H11ClN2O4 was synthesized and structurally characterized using single crystal X-ray diffraction technique. The vibrational properties of the crystal were studied by Fourier Transform infrared (FT-IR), Fourier Transform Raman (FT-Raman) techniques and theoretical calculations of quantum chemistry using Density functional theory (DFT) and Density functional perturbation theory (DFPT). A comparison with experimental spectra allowed the assignment of all the normal modes. The descriptions of the normal modes were carried by means of potential energy distribution (PED). Additionally, analysis of the antimicrobial activity and antibiotic resistance modulatory activity was carried out to evaluate the antibacterial potential of the CYMM.

  16. The influence of solvent stress on MMS-induced genetic change in Saccharomyces cerevisiae.

    Science.gov (United States)

    Zimmermann, F K; Rohlfs, A

    1991-01-01

    MMS induced mitotic recombination but not mitotic chromosome loss when tested in pure form in strain D61.M of Saccharomyces cerevisiae, confirming previous results of Albertini (1991), whereas in Aspergillus nidulans it also induced chromosomal malsegregation in addition to mitotic recombination (Käfer, 1988). However, induction of mitotic chromosome loss was observed in combination with strong inducers of chromosome loss such as the aprotic polar solvents ethyl acetate and to a lesser extent methyl ethyl ketone but not with gamma-valerolactone and propionitrile. In addition to this, 4 solvents, dimethyl formamide, dimethyl sulfoxide, dioxane and pyridine, enhanced the MMS-induced mitotic recombination in strain D61.M. An enhancement of MMS-induced mitotic recombination and reverse mutation could be demonstrated for ethyl acetate and gamma-valerolactone in yeast strain D7.

  17. A Study on Copolymer Systems of Styrene with Diethanolamine Side Group and Methyl Methacrylate

    Directory of Open Access Journals (Sweden)

    Aslisah Acikses

    2018-01-01

    Full Text Available 4-Diethanolaminomethyl styrene (DEAMSt monomer was prepared by the modification of 4-chloromethyl styrene with diethanolamine. The copolymers in different combinations (0.11, 0.19, and 0.30 by mole of DEAMSt and methyl methacrylate (MMA were prepared by free radical polymerization method at 60°C in the presence of 1,4-dioxane and AIBN as initiator. The structures of DEAMSt and DEAMSt-MMA copolymer were characterized by FT-IR and 1H-NMR. The glass transition temperature (Tg of the copolymers was measured by DSC. Thermal decomposition behavior of the copolymers was investigated by TGA. The average molecular weights of the copolymers were determined by GPC. The dye uptaking properties of the copolymers were investigated using bromocresol green. Then, the dielectric constant, dielectric loss factor, and conductivity of copolymers were investigated as a function of temperature and frequency. The activation energies (Ea of the copolymers were determined by impedance analyzer.

  18. From micelle supramolecular assemblies in selective solvents to isoporous membranes

    KAUST Repository

    Nunes, Suzana Pereira

    2011-08-16

    The supramolecular assembly of PS-b-P4VP copolymer micelles induced by selective solvent mixtures was used to manufacture isoporous membranes. Micelle order in solution was confirmed by cryo-scanning electron microscopy in casting solutions, leading to ordered pore morphology. When dioxane, a solvent that interacts poorly with the micelle corona, was added to the solution, polymer-polymer segment contact was preferential, increasing the intermicelle contact. Immersion in water gave rise to asymmetric porous membranes with exceptional pore uniformity and high porosity. The introduction of a small number of carbon nanotubes to the casting solution improved the membrane stability and the reversibility of the gate response in the presence of different pH values. © 2011 American Chemical Society.

  19. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-[(1H-benzimidazol-2-yl-methylene) amino] phenol

    International Nuclear Information System (INIS)

    Omprakash, K.L.; Chandra Pal, A.V.; Reddy, M.L.N.

    1982-01-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO 4 ) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (logβ 2 ) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III). (author)

  20. Stability constant for thorium(IV) complexes with aryl bis-(5-hydroxy-3-methyl-1-phenyl-4-pyrazolyl)-methane ligands

    Energy Technology Data Exchange (ETDEWEB)

    Stefan, L.S. [Ain Shams Univ., Cairo (Egypt)

    1995-09-01

    Chelate stability constants of aryl bis(5-hydroxy-3-methyl-1-phenyl-4-pyrazolyl)methane (ABPM) derivatives with thorium(IV) ion were determined by the potentiometric method at 30 C and 0.1 mol dm{sup -3} (KNO{sub 3}) in 75% (v/v) dioxane-water solvent. The computation of the titration data indicated that four kinds of complexes [ThL]{sup 2+}, [ThL(OH)]{sup +}, [ThL{sub 2}] and [ThL(OH){sub 2}] were formed. The appropriate formation constants for all of the 1:1 species and 2:1 complexes have been calculated are probable ligand-banding sites of the complexes were proposed. In addition, the applicability of the Hammett equation for correlation of the stability constants of [Th(IV)-ABPM] complexes was discussed. (author). 19 refs, 5 figs, 1 tab.

  1. Stability constant for thorium(IV) complexes with aryl bis-(5-hydroxy-3-methyl-1-phenyl-4-pyrazolyl)-methane ligands

    International Nuclear Information System (INIS)

    Stefan, L.S.

    1995-01-01

    Chelate stability constants of aryl bis(5-hydroxy-3-methyl-1-phenyl-4-pyrazolyl)methane (ABPM) derivatives with thorium(IV) ion were determined by the potentiometric method at 30 C and 0.1 mol dm -3 (KNO 3 ) in 75% (v/v) dioxane-water solvent. The computation of the titration data indicated that four kinds of complexes [ThL] 2+ , [ThL(OH)] + , [ThL 2 ] and [ThL(OH) 2 ] were formed. The appropriate formation constants for all of the 1:1 species and 2:1 complexes have been calculated are probable ligand-banding sites of the complexes were proposed. In addition, the applicability of the Hammett equation for correlation of the stability constants of [Th(IV)-ABPM] complexes was discussed. (author). 19 refs, 5 figs, 1 tab

  2. Imidazolium-Based Ionic Liquids as Efficient Reagents for the C-O Bond Cleavage of Lignin.

    Science.gov (United States)

    Thierry, Marina; Majira, Amel; Pégot, Bruce; Cezard, Laurent; Bourdreux, Flavien; Clément, Gilles; Perreau, François; Boutet-Mercey, Stéphanie; Diter, Patrick; Vo-Thanh, Giang; Lapierre, Catherine; Ducrot, Paul-Henri; Magnier, Emmanuel; Baumberger, Stéphanie; Cottyn, Betty

    2018-01-23

    The demethylation of lignin in ionic liquids (ILs) was investigated by using pure lignin model monomers and dimers together with dioxane-isolated lignins from poplar, miscanthus, and maize. Different methylimidazolium ILs were compared and the samples were treated with two different heating processes: microwave irradiation and conventional heating in a sealed tube. The conversion yield and influence of the treatment on the lignin structure were assessed by 31 P NMR spectroscopy, size-exclusion chromatography, and thioacidolysis. The acidic methylimidazolium IL [HMIM]Br was shown to be an effective combination of solvent and reagent for the demethylation and depolymerization of lignin. The relatively mild reaction conditions, the clean work-up, and the ability to reuse the IL makes the described procedure an attractive and new green method for the conversion of lignin to produce phenol-rich lignin oligomers. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Preparation and LSC Standardization of ''89Sr (DNP) Using the CIEMAT/NIST Method; Preparacion del ''89Sr(DNP) y calibracion por centelleo liquido, mediante el metodo CIEMAT/NIST

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Barquero, L.; Los Arcos Merino, J. M.; Grau Malonda, A.

    1994-07-01

    A procedure for preparation of liquid scintillation counting samples of the strontium DNP complex, labelled with ''89Sr, is described, the chemical quench, the counting stability and spectral evolution of this compound is studied in six scintillators, Toluene, Toluene-alcohol, Dioxane-naphthalene, HiSafe II, Ultima- Gold and Instagel. The liquid scintillation standardization of 89Sr-DNP by the CIEMAT/NIST method, using HiSafe II and Ultima-Gold scintillators, has been carried out. The discrepancies between experimental and computed efficiencies are lower than 0.38% and 0.48%, respectively. The solution has been standardized in terms of activity concentration to an overall uncertainty of 0,38%. (Author) 10 refs.

  4. Reversed-phase thin-layer chromatography behavior of aldopentose derivatives

    Directory of Open Access Journals (Sweden)

    Malbaša Radomir V.

    2012-01-01

    Full Text Available Quantitative structure-retention relationships (QSRR have been used to study the chromatographic behavior of some aldopentose. The behavior of aldopentose derivatives was investigated by means of the reversed-phase thin-layer chromatography (RP TLC on the silica gel impregnated with paraffin oil stationary phases. Binary mixtures of methanol-water, acetone-water and dioxane-water were used as mobile phases. Retention factors, RM0, corresponding to zero percent organic modifier in the aqueous mobile phase was determined. Lipophilicity C0 was calculated as the ratio of the intercept and slope values. There was satisfactory correlation between them and log P values calculated using different theoretical procedures. Some of these correlations offer very good predicting models, which are important for a better understanding of the relationships between chemical structure and retention. The study showed that the hydrophobic parameters RM0 and C0 can be used as a measures of lipophilicity of investigated compounds.

  5. Nano-ZnO Catalyzed Multicomponent One-Pot Synthesis of Novel Spiro(indoline-pyranodioxine Derivatives

    Directory of Open Access Journals (Sweden)

    Harshita Sachdeva

    2014-01-01

    Full Text Available A simple catalytic protocol for the synthesis of novel spiro[indoline-pyranodioxine] derivatives has been developed using ZnO nanoparticle as an efficient, green, and reusable catalyst. The derivatives are obtained in moderate to excellent yield by one-pot three-component reaction of an isatin, malononitrile/ethylcyanoacetate, and 2,2-dimethyl-1,3-dioxane-4,6-dione in absolute ethanol under conventional heating and microwave irradiation. The catalyst was recovered by filtration from the reaction mixture and reused during five consecutive runs without any apparent loss of activity for the same reaction. The mild reaction conditions and recyclability of the catalyst make it environmentally benign synthetic procedure.

  6. Behaviour of polycrystalline fluoride-selective membrane electrode in aqueous-organic media

    International Nuclear Information System (INIS)

    Manakova, L.I.; Bausova, N.V.; Moiseev, V.E.; Bamburov, V.G.; Sivoplyas, A.P.

    1978-01-01

    The behaviour of polycrystalline fluoride membrane electrode (RFME) in aqueous-organic media has been studied when the content of the organic component (methanol, ethanol, acetone, dioxane) has been changed from 20 to 80 mass%. Since LaF 3 is the base of the membrane, its solubility has been studied depending on the organic component content in the solution. It has been established that LaF 3 solubility decreases with increasing content of of the organic component. This explains the effect of the composition of an aqueous-organic solvent on the electrode sensitivity. The electrode sensitivity rises with increasing content of the organic component in an aqueous-organic solvent. A greater decrease of LaF 3 solubility in aqueous-organic solvents as compared with that of LaCl 3 , La(NO 3 ) 3 , and La 2 (SO 4 ) 3 causes a higher selectivity of RFME with respect to the anions under study

  7. Acid- and base-catalysis in the mononuclear rearrangement of some (Z)-arylhydrazones of 5-amino-3-benzoyl-1,2,4-oxadiazole in toluene: effect of substituents on the course of reaction.

    Science.gov (United States)

    D'Anna, Francesca; Frenna, Vincenzo; Ghelfi, Franco; Marullo, Salvatore; Spinelli, Domenico

    2011-04-15

    The reaction rates for the rearrangement of eleven (Z)-arylhydrazones of 5-amino-3-benzoyl-1,2,4-oxadiazole 3a-k into the relevant (2-aryl-5-phenyl-2H-1,2,3-triazol-4-yl)ureas 4a-k in the presence of trichloroacetic acid or of piperidine have been determined in toluene at 313.1 K. The results have been related to the effect of the aryl substituent by using Hammett and/or Ingold-Yukawa-Tsuno correlations and have been compared with those previously collected in a protic polar solvent (dioxane/water) as well as with those on the analogous rearrangement of the corresponding (Z)-arylhydrazones of 3-benzoyl-5-phenyl-1,2,4-oxadiazole 1a-k in benzene. Some light can thus be shed on the general differences of chemical reactivity between protic polar (or dipolar aprotic) and apolar solvents.

  8. Fiscal 1998 R and D on original advanced material creation technology (development of precise structure control materials for oil refinery improvement). R and D result report on multi-dimensional polymers; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho. Tajigen kukan polymer no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of radical-controlled synthesis technology of aromatic compounds using enzyme-related catalysts and synthesis technology of ordered compounds, and development of synthesis technology of new polymer groups with non-covalent bond linkages and new topological structures, this R and D on multi-dimensional polymers is promoting 2 research themes, (1) precise polymer synthesis technology using enzyme-related catalysts, and (2) chemical synthesis technology for polymers with non-covalent bond linkages and new topological structures. The joint research on (1) precise polymer synthesis technology using enzyme-related catalysts established the high-yield synthesis technology of phenol dimer first in the world. The joint research first studied the synthesis using 2,6-dimethylphenol as monomer through synthesis of phenol groups using ferrosalen, and obtained the mixture of polymer components more than 10,000 in molecular weight and low-molecular weight components by using 1,4- dioxane as solvent. (NEDO)

  9. First-principles quantum-mechanical investigations: The role of water in catalytic conversion of furfural on Pd(111)

    Science.gov (United States)

    Xue, Wenhua; Borja, Miguel Gonzalez; Resasco, Daniel E.; Wang, Sanwu

    2015-03-01

    In the study of catalytic reactions of biomass, furfural conversion over metal catalysts with the presence of water has attracted wide attention. Recent experiments showed that the proportion of alcohol product from catalytic reactions of furfural conversion with palladium in the presence of water is significantly increased, when compared with other solvent including dioxane, decalin, and ethanol. We investigated the microscopic mechanism of the reactions based on first-principles quantum-mechanical calculations. We particularly identified the important role of water and the liquid/solid interface in furfural conversion. Our results provide atomic-scale details for the catalytic reactions. Supported by DOE (DE-SC0004600). This research used the supercomputer resources at NERSC, of XSEDE, at TACC, and at the Tandy Supercomputing Center.

  10. Direct Alkynylation of 3H-Imidazo[4,5-b]pyridines Using gem-Dibromoalkenes as Alkynes Source.

    Science.gov (United States)

    Aziz, Jessy; Baladi, Tom; Piguel, Sandrine

    2016-05-20

    C2 direct alkynylation of 3H-imidazo[4,5-b]pyridine derivatives is explored for the first time. Stable and readily available 1,1-dibromo-1-alkenes, electrophilic alkyne precursors, are used as coupling partners. The simple reaction conditions include an inexpensive copper catalyst (CuBr·SMe2 or Cu(OAc)2), a phosphine ligand (DPEphos) and a base (LiOtBu) in 1,4-dioxane at 120 °C. This C-H alkynylation method revealed to be compatible with a variety of substitutions on both coupling partners: heteroarenes and gem-dibromoalkenes. This protocol allows the straightforward synthesis of various 2-alkynyl-3H-imidazo[4,5-b]pyridines, a valuable scaffold in drug design.

  11. Lignin and related compounds. VIII. Lignin monomers and dimers from hydrogenolysis of aspen wood using rhodium-on-charcoal catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Sudo, K; Mullord, D J; Pepper, J M

    1981-04-01

    Aspen poplar wood meal has been subjected to catalytic hydrogenolysis in dioxane-water (9:1) at 500 psig initial pressure of hydrogen over a 5% rhodium-on-charcoal catalyst for five hours at 195 plus or minus 5 degrees C. The resulting chloroform-soluble lignin degradation products were separated by cellulose and silica gel column chromatography. The following compounds were isolated and identified: 4-hydroxybenzoic acid, 1-(4-hydroxy-3,4-dimethoxyphenyl)-1-propanone (propiosyringone), 2,2'-dihydroxy-3,3'-dimethoxy- 5,5'-dipropylbiphenyl, 2,3-bis(4-hydroxy-3,5- dimethoxyphenyl)-1-propanol, and a mixture of 3-(4-hydroxy-3,5-dimethoxyphenyl)-2(4-hydroxy- 3-methoxyphenyl)-1-propan and 3-(4-hydroxy-3- methoxyphenyl)-2-(4-hydroxy-3,5-dimethoxyphenyl)-1- propanol. 9 references.

  12. From micelle supramolecular assemblies in selective solvents to isoporous membranes

    KAUST Repository

    Nunes, Suzana Pereira; Karunakaran, Madhavan; Neelakanda, Pradeep; Behzad, Ali Reza; Hooghan, Bobby; Sougrat, Rachid; He, Haoze; Peinemann, Klaus-Viktor

    2011-01-01

    The supramolecular assembly of PS-b-P4VP copolymer micelles induced by selective solvent mixtures was used to manufacture isoporous membranes. Micelle order in solution was confirmed by cryo-scanning electron microscopy in casting solutions, leading to ordered pore morphology. When dioxane, a solvent that interacts poorly with the micelle corona, was added to the solution, polymer-polymer segment contact was preferential, increasing the intermicelle contact. Immersion in water gave rise to asymmetric porous membranes with exceptional pore uniformity and high porosity. The introduction of a small number of carbon nanotubes to the casting solution improved the membrane stability and the reversibility of the gate response in the presence of different pH values. © 2011 American Chemical Society.

  13. An overview of the Environmental Response Team's air surveillance procedures at emergency response activities

    Energy Technology Data Exchange (ETDEWEB)

    Turpin, R.D.; Campagna, P.R. (U.S. Environmental Protection Agency, Edison, NJ (USA))

    The Safety and Air Surveillance Section of the United States Environmental Protection Agency's Environmental Response Team responds to emergency air releases such as tire fires and explosions. The air surveillance equipment and procedures used by the organization are described, and case studies demonstrating the various emergency response activities are presented. Air response activities include emergency air responses, occupational and human health air responses and remedial air responses. Monitoring and sampling equipment includes photoionization detectors, combustible gas meters, real-time aerosol monitors, personal sampling pumps, and high flow pumps. Case histories presented include disposal of dioxane from a cotton plant, response to oil well fires in Kuwait, disposal of high pressure cylinders in American Samoa, and response to hurricane Hugo. 3 refs., 1 tab.

  14. The Pd-catalyzed hydrodechlorination of chlorophenols in aqueous solutions under mild conditions: A promising approach to practical use in wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Xia Chuanhai, E-mail: chuanhaixia@gmail.com [Yantai Institute of Coastal Zone Research for Sustainable Development, CAS, Yantai 264003 (China); Liu Ying; Zhou Shiwei; Yang Cuiyun; Liu Sujing [Yantai Institute of Coastal Zone Research for Sustainable Development, CAS, Yantai 264003 (China); Xu Jie [Dalian Institute of Chemical Physics, CAS, Dalian, 116021 (China); Yu Junbao [Yantai Institute of Coastal Zone Research for Sustainable Development, CAS, Yantai 264003 (China); Chen Jiping; Liang Xinmiao [Dalian Institute of Chemical Physics, CAS, Dalian, 116021 (China)

    2009-09-30

    Catalytic hydrotreating of chlorophenols was carried out in water with Pd/C at 25 deg. C under atmospheric pressure. 1.0% (w/w) monocholophenols was completely dechlorinated within 60 min. Phenol, cyclohexanone and cyclohexanol were formed. In contrast to the dechlorination of monochlorophenols, the hydrogenation reaction of polychlorinated phenols became difficult and reaction rates were strongly dependent upon the number of the chlorine atoms. The solvent property had a considerably important influence on the dechlorination reaction. Water as a solvent showed more advantages than organic solvents. It was much easier to be hydrodechlorinated for chlorophenols in aqueous solutions. However, the presence of THF, dioxane, DMSO or DMF in water was disadvantageous to the reaction and easily to cause Pd/C deactivation. Additionally, when different halogenated organic compounds were present in aqueous solution, the dehalogenation reaction was the competitive hydrogenation process.

  15. Activity measurement of 33P and 32P radionuclide mixture

    International Nuclear Information System (INIS)

    Hanker, I.; Kansky, Z.

    1984-01-01

    The possibilities are briefly summed up of measuring mixtures of 33 P and 32 P with special regard to the method of simultaneous determination of both radionuclides in a liquid scintillator. This method was experimentally tested for special detection sensitivity and intended special applications in plant physiology and biochemistry using a dioxane scintillator (SLD-31, Spolana Neratovice, CSSR) and a Packard Tri-Carb 300 C, USA. The method gave erroneous results. The main cause of the errors in measurements of the 33 P and 32 P mixture in the SLD-31 was the adsorption of radionuclides on the inner wall of glass tubes. This phenomenon is not accompanied by changes in the quenching index. However, the effectiveness of measurement dropped and the relative contribution of the spectra of the two radionuclides changed with the time following sample preparation. The said effects were removed by adding 0.4% silicon dioxide (Cab-O-Sil M5, Serva) to the liquid scintillator. (author)

  16. Gas chromatographic-mass spectrometric determination of hydrophilic compounds in environmental water by solid-phase extraction with activated carbon fiber felt.

    Science.gov (United States)

    Kawata, K; Ibaraki, T; Tanabe, A; Yagoh, H; Shinoda, A; Suzuki, H; Yasuhara, A

    2001-03-09

    Simple gas chromatographic-mass spectrometric determination of hydrophilic organic compounds in environmental water was developed. A cartridge containing activated carbon fiber felt was made by way of trial and was evaluated for solid-phase extraction of the compounds in water. The hydrophilic compounds investigated were acrylamide, N,N-dimethylacetamide, N,N-dimethylformamide, 1,4-dioxane, furfural, furfuryl alcohol, N-nitrosodiethylamine and N-nitrosodimethylamine. Overall recoveries were good (80-100%) from groundwater and river water. The relative standard deviations ranged from 4.5 to 16% for the target compounds. The minimum detectable concentrations were 0.02 to 0.03 microg/l. This method was successfully applied to several river water samples.

  17. Preparation and LSC standardization of ''89 Sr (DNP) using the CIEMAT/NIST method

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Arcos Merino, J.M. Los; Grau Malonda, A.

    1994-01-01

    A procedure for preparation of liquid scintillation counting samples of the strontium DNP complex, labelled with ''89 Sr, is described. The chemical quench, the counting stability and spectral evolution of this compound is studied in six scintillators, Toluene, Toluene-alcohol, Dioxane-naphthalene, HiSafe II, Ultima-Gold and Instagel. The liquid scintillation standardization of ''89Sr-DNP by the CIEMAT/NIST method, using Hisafe II and Ultima-Gold scintillators, has been carried out. The discrepancies between experimental and computed efficiencies are lower than 0.38% and 0.48%, respectively. The solution has been standardized in terms of activity concentration to an overall uncertainty of 0.38%. (Author)

  18. Configurational properties of aromatic polyesters with sulfur atoms in their structure

    International Nuclear Information System (INIS)

    Riande, E.; Guzman, J.; Roman, J.S.

    1980-01-01

    The dipole moments of poly (thiodiethylene glycol terephthalate) chains were determined as a function of temperature by means of dielectric constant measurements in dioxane. The experimental results were found to be in fair agreement with theoretical results based on a rotational isomeric state model in which the required conformational energies were obtained from previous configurational analysis on poly(ethylene terephthalate), poly(diethylene glycol terephthalate) and poly(thiodiethylene glycol). Since poly(thiodiethylene glycol terephthalate) can be considered an alternating copolymer of ethylene terephthalate and thioethylene units, its configuration-dependent properties were compared with those of poly(ethylene terephthalate) and poly(ethylene sulfide). It was found the flexibility of the copolymer, as expressed by the partition function, intermediate to that of its parent homopolymers. The theoretical results also indicate that the dimensions of poly(thiodiethylene glycol) are similar to those of poly(ethylene terephthalate) while its dipole moment ratio resembles that of poly

  19. Extraction of carbon 14-labeled compounds from plant tissue during processing for electron microscopy

    International Nuclear Information System (INIS)

    Coetzee, J.; van der Merwe, C.F.

    1989-01-01

    Loss of 14 C-labeled compounds from bean leaf tissue was monitored during all the stages of routine specimen preparation. No significant differences in extraction were associated with the use of acetone, ethanol, or dioxane as dehydration fluids. Fixation at low temperature increased the loss of label. Prolonged fixation in glutaraldehyde increased the loss, but fixation in osmium solutions for periods as long as 4 hr had no influence on extraction. Buffer rinses and dehydration fluids caused appreciable amounts of label to be extracted. The use of propylene oxide as transition fluid resulted in low extraction. Some embedding media caused the loss of small amounts of labeled compounds, but one of the media tested (LR-white) extracted significant amounts of label

  20. Singlet oxygen reactivity in water-rich solvent mixtures

    Directory of Open Access Journals (Sweden)

    Cristina Sousa

    2008-01-01

    Full Text Available The 3-methylindole (3MI oxygenation sensitized by psoralen (PSO has been investigated in 100%, 20% and 5% O2-saturated water/dioxane (H2O/Dx mixtures. The lowering of the ¹O2* chemical rate when water (k chem∆3MI = 1.4 × 109 M-1 s-1 is replaced by deuterated water (k chem∆3MI = 1.9 × 108 M-1 s-1 suggests that hydrogen abstraction is involved in the rate determining step. A high dependence of the chemical rate constant on water concentration in H2O/Dx mixtures was found showing that water molecules are absolutely essential for the success of the 3MI substrate oxidation by ¹O2* in water-rich solvent mixtures.

  1. Measurement of the quantity of water in organic solvents by infrared absorption an measurement of the dielectric constants

    International Nuclear Information System (INIS)

    Desnoyer, M.

    1959-06-01

    Some chemical methods for the analysis of the quantity of water in solvents are first described, their object being the determination of the maximum error for cases where the water content is less than 1 per cent. - The first part of the work consists in describing infrared spectrometry as applied to the analysis of water in carbon tetrachloride, chloroform aniline, acetone and dioxane. A method based on isotopic exchange between heavy and light water is used on the one hand for determining the solubility of water in carbon tetrachloride and on the other hand for establishing standard solutions (sensitivity of the method). - In the second part the dielectric constant of water solvent solutions is measured. A table is presented giving the precision obtained by the two principal methods. These are comparable and further than that the appearance of the spectra suggests an interpretation of the anomalies observed in calibration curves obtained by the dielectric constant method. (author) [fr

  2. Chemical models of chains electron transfer in hydroxylating ferment systems

    International Nuclear Information System (INIS)

    Akhrem, A.A.; Kiselev, P.A.; Metelitsa, D.I.

    1977-01-01

    The rate constants are measured of consumption of nicotineamidedinucleotide (NAD-N) during its oxidation by molecular oxygen with the participation of Ti 4+ , Sn 4+ , Cu 2+ , Fe 3+ , VO 2+ , and Ce 4+ ions in mixtures of acetonitrile with water and of dioxane with water taken in a volume ratio of 1:1 (46 deg C). The kinetics of oxidation of NAD-N with the participation of Ti 4+ at 37 deg C in a water-acetonitrile medium is studied in detail. The hydroxylating capacity of the system NAD-N - Ti 4+ - O 2 with respect to naphthalene is proved. The reaction mechanism and its relationship with the microsomal chains of electron transport are discussed

  3. Synthesis and Characterization of Some New Thermal Stable Polymers - Polymerization of N-[4-N´ -(Benzylamino-carbonylphenyl]maleimide

    Directory of Open Access Journals (Sweden)

    B. L. Hiran

    2007-01-01

    Full Text Available This article describes the synthesis and characterization of homopolymer (H-BCPM of N-[4-N'-(benzylamino-carbonyl phenyl] maleimide (N-BACPMI and copolymer (C-BCPM of N-BACPMI with n-butyl acrylate (BA. The new monomer was synthesized from p-aminobenzoic acid, maleic anhydride and benzylamine. The homopolymerization of N-BACPMI is initiated by free radical using AIBN in THF solvent at 65°C. Radical copolymerization of N-BACPMI with BA, initiated by AIBN, was performed in THF solvent using equimolar amount. Effect of the different free radical initiator AIBN, BPO and solvents p-Dioxane, THF, DMF and DMSO was studied. Homopolymer and Copolymer were characterized by intrinsic viscosity, solubility test, FT-IR, 1H-NMR spectral analysis and elemental analysis. Thermal behaviour was studied by Thermo gravimetric analysis.

  4. Hydrogenation of Isophthalonitrile with 1-Methylimidazole as an Effective Solvent for m-Xylenediamine Production

    Energy Technology Data Exchange (ETDEWEB)

    Chae, Tae Young; Row, Sung Wook; Yoo, Kye Sang; Lee, Sang Duek [Environment and Process Technology Division, Seoul (Korea, Republic of); Lee, Do Weon [University of Seoul, Seoul (Korea, Republic of)

    2006-03-15

    1-methylimidazole was shown to outperform the other organic solvents in this reaction. Moreover, amount of ammonia with using 1-methylimidazole as a solvent was lower than other processes. Thus, 1-methylimidazole is an attractive solvent in IPN hydrogenation for the production of MXDA. The correct choice of a solvent is a critical factor to govern the catalytic activity with desirable hydrogenation. Conventionally, organic materials such as aromatic hydrocarbons, aliphatic alcohols, aliphatic hydrocarbons, dimethylformamide and dioxane were employed in this reaction. Several MXDA producing processes with the organic solvent including m-xylene, pseudocumene, mesitylene, ethylbenzene, methylpyridine, benzonitrile, m-tolunitrile, MXDA and cyanopyridine were disclosed. However, the solvents and ammonia were vaporized under the operation conditions leading to amine cleavage with the resulting formation of methylbenzyl amines or the consumption of ammonia was still significant. Recently, some researchers reported that a high yield of MXDA was achieved using isopropanol under relatively low pressure condition; however, the consumption of ammonia was very significant.

  5. Comparative Analysis of Milled Wood Lignins (MWLs Isolated from Sugar Maple (SM and Hot-Water Extracted Sugar Maple (ESM

    Directory of Open Access Journals (Sweden)

    Mangesh J. Goundalkar

    2014-03-01

    Full Text Available To further elucidate the advantageous effects of hot-water extraction (HWE on delignification, milled wood lignin (MWL was isolated from sugar maple (SM and from hot-water extracted sugar maple (ESM. Ball-milled wood was analyzed for particle size distribution (PSD before and after dioxane:water (DW extraction. The MWL samples were analyzed by analytical and spectral methods. The results indicated that the MWL isolated from SM and ESM was mainly released from the middle lamella (ML and the secondary wall (SW, respectively. The cleavage of dibenzodioxocin (DB and spirodienone (SD lignin substructures during HWE is suggested. The removal of lignin during acetone:water (AW extraction of hot-water extracted wood indicates that including an additional operation in a hardwood HWE-based biorefinery would be beneficial for processing of wood.

  6. Compatibility of nitrilotriacetic acid and 3-acetyl-4-hydroxy-6-methyl-2-pyrone in the coordination sphere of lanthanon ions

    International Nuclear Information System (INIS)

    Kadian, R.K.; Garg, B.S.; Singh, R.P.

    1982-01-01

    A study of the competetion of 3-acetyl-4-hydroxy-6-methyl-2-pyrone (dehydracetic acid, DHA) and nitrilotriacetic acid (NTA) in the coordination sphere of lanthanon ions has been carried out by calculating reproportionation constant which relates the stability of the mixed ligand complex to those of the parent complexes formed by the same ligands. It has been found that NTA and DHA are incompatible ligands and mixed ligand complexes formed are less stable than either of the parent complexes. The fact is also supported by the observed change in free energy occuring during mixed ligand complex formation. All these studies have been carried out at 30.0 +- 0.5 0 and μ-0.01 (NaClO 4 ) in 50 percent v/v aqueous dioxane medium. (author)

  7. The Pd-catalyzed hydrodechlorination of chlorophenols in aqueous solutions under mild conditions: A promising approach to practical use in wastewater

    International Nuclear Information System (INIS)

    Xia Chuanhai; Liu Ying; Zhou Shiwei; Yang Cuiyun; Liu Sujing; Xu Jie; Yu Junbao; Chen Jiping; Liang Xinmiao

    2009-01-01

    Catalytic hydrotreating of chlorophenols was carried out in water with Pd/C at 25 deg. C under atmospheric pressure. 1.0% (w/w) monocholophenols was completely dechlorinated within 60 min. Phenol, cyclohexanone and cyclohexanol were formed. In contrast to the dechlorination of monochlorophenols, the hydrogenation reaction of polychlorinated phenols became difficult and reaction rates were strongly dependent upon the number of the chlorine atoms. The solvent property had a considerably important influence on the dechlorination reaction. Water as a solvent showed more advantages than organic solvents. It was much easier to be hydrodechlorinated for chlorophenols in aqueous solutions. However, the presence of THF, dioxane, DMSO or DMF in water was disadvantageous to the reaction and easily to cause Pd/C deactivation. Additionally, when different halogenated organic compounds were present in aqueous solution, the dehalogenation reaction was the competitive hydrogenation process.

  8. Cyanoacetanilides intermediates in heterocyclic synthesis. Part 6: Preparation of some hitherto unknown 2-oxopyridine, bipyridine, isoquinoline and chromeno[3,4-c]pyridine containing sulfonamide moiety

    Directory of Open Access Journals (Sweden)

    Yousry A. Ammar

    2014-11-01

    Full Text Available Treatment of cyanoacetanilide derivative 1 with tetracyanoethylene (2 in dioxane/triethylamine furnished 2-pyridone derivative 6. Aminopyridine 9 was obtained by cyclization of compound 1 with ketene dithioacetal 7/EtONa. Cyclocondensation of 1 with malononitrile and/or acetylacetone (1:1 M ratio gave pyridine derivatives 11 and 13. Ternary condensation of compound 1, aliphatic aldehydes and malononitrile (1:1:1 M ratio yielded the 2-pyridones 20a and b. Bipyridines 22a–c were prepared by refluxing of compound 21 with active methylene reagents. Cyclization of chromene derivatives 24 and 28 with malononitrile produced the novel chromeno[3,4-c]pyridine 26 and pyrano[3′,2′:6,7]chromeno[3,4-c]pyridine 29.

  9. An Efficient Synthesis of Novel Pyrazole-Based Heterocycles as Potential Antitumor Agents

    Directory of Open Access Journals (Sweden)

    Magda A. Abdallah

    2017-08-01

    Full Text Available A new series of pyrazolylpyridines was prepared by reaction of ethyl-3-acetyl-1,5-diphenyl-1H-pyrazole-4-carboxylate with the appropriate aldehyde, malononitrile, or ethyl acetoacetate and an excess of ammonium acetate under reflux in acetic acid. Similarly, two novel bipyridine derivatives were prepared by the above reaction using terephthaldehyde in lieu of benzaldehyde derivatives. In addition, a series of 1,2,4-triazolo[4,3-a]pyrimidines was synthesized by a reaction of 6-(pyrazol-3-ylpyrimidine-2-thione with a number of hydrazonoyl chlorides in dioxane and in the presence of triethylamine. The structure of the produced compounds was established by elemental analyses and spectral methods, and the mechanisms of their formation was discussed. Furthermore, the pyrazolyl-pyridine derivatives were tested as anticancer agents and the results obtained showed that some of them revealed high activity against human hepatocellular carcinoma (HEPG2 cell lines.

  10. Low level scintillation counting of 239Pu

    International Nuclear Information System (INIS)

    Fueloep, M.; Minarik, F.; Cierna, V.

    1984-01-01

    For measuring the content of 239 Pu in samples taken from the working or living environment, methods should be used which are sufficiently sensitive for determining activities of the order of 10 -3 Bq. It is useful to use liquid scintillators for reasons of their 4π geometry and the exclusion of kinetic energy losses of particles detected in the sample and on the path between the sample and the detector. The method of background discrimination according to pulse shape may be used to suppress gamma background in the area of alpha particle peaks to the level 2.5x10 -4 s -1 . The diagram is given of electronic circuits for shape discrimination. The scintillator used was a SLS-31 with a PBD activator, a POPOP spectrum shifter and a mixture of solvents: toluene, dioxane and methanol. The efficiency of 239 Pu alpha particle detection is estimated at 78% and may further be improved by improving shape discrimination. (M.D.)

  11. Synthesis, catalytic and biological activity of novel dinuclear copper complex with Schiff base

    Institute of Scientific and Technical Information of China (English)

    WEI Danyi; LI Ning; LU Gui; YAO Kemin

    2006-01-01

    A novel dinuclear copper complex with tetraglycol aldehyde-phenylalanine Schiff base has been synthesized. It was characterized and formulated as [Cu2L(NO3)]NO3 by elemental analysis,magnetic susceptibility, TG-DTA, IR, EPR and 1H NMR spectra. The obtained complex can be used as a good catalyst for the polymerization of methyl methacrylate (MMA). The optimum polymerization conditions are: MMNcatalyst = 500 (molar ratio); [catalyst] = 7.5×10-3 mol. L-1; dioxane as solvent;80℃; 6 h. Polymethyl methacrylate (PMMA) with 80% conversion, 7.2×105 viscosity-average molecular weight and 60.5% syndiotacticity was obtained. This complex has also been shown to play an important role in scavenging O-·2.

  12. Furfural production from Eucalyptus wood using an Acidic Ionic Liquid.

    Science.gov (United States)

    Peleteiro, Susana; Santos, Valentín; Garrote, Gil; Parajó, Juan Carlos

    2016-08-01

    Eucalyptus globulus wood samples were treated with hot, compressed water to separate hemicelluloses (as soluble saccharides) from a solid phase mainly made up of cellulose and lignin. The liquid phase was dehydrated, and the resulting solids (containing pentoses as well as poly- and oligo- saccharides made up of pentoses) were dissolved and reacted in media containing an Acidic Ionic Liquid (1-butyl-3-methylimidazolium hydrogen sulfate) and a co-solvent (dioxane). The effects of the reaction time on the product distribution were studied at temperatures in the range 120-170°C for reaction times up to 8h, and operational conditions leading to 59.1% conversion of the potential substrates (including pentoses and pentose structural units in oligo- and poly- saccharides) into furfural were identified. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Solvent extraction of hafnium(IV) by dinonylnaphthalene sulfonic acid from mixed aqueous-organic media

    International Nuclear Information System (INIS)

    Hala, J.; Piperkovova, H.

    1979-01-01

    The extraction of hafnium(IV) by heptane and toluene solutions of dinonylnaphthalene sulfonic acid (HD) from mixed aqueous-organic solutions has been studied. Alcohols, ketones, carboxylic acids, cyclic ethers, dimethylsulfoxide and dimethylformamide were used as the organic component of the mixed phase. Methanol, ethanol, formic acid and dioxane increased the extractability of Hf(IV) whereas other solvents showed only an antagonistic effect. The results were discussed from the point of view of the changes in micellar structure of HD, and compared with the uptake of Hf(IV) by resinous cation exchangers. The solubilization by HD of alcohols, carboxylic acids and dimethylsulfoxide was demonstrated by using the corresponding 14 C and 35 S labelled compounds. (author)

  14. Dielectric relaxation studies of dilute solutions of amides

    Energy Technology Data Exchange (ETDEWEB)

    Malathi, M.; Sabesan, R.; Krishnan, S

    2003-11-15

    The dielectric constants and dielectric losses of formamide, acetamide, N-methyl acetamide, acetanilide and N,N-dimethyl acetamide in dilute solutions of 1,4-dioxan/benzene have been measured at 308 K using 9.37 GHz, dielectric relaxation set up. The relaxation time for the over all rotation {tau}{sub (1)} and that for the group rotation {tau}{sub (2)} of (the molecules were determined using Higasi's method. The activation energies for the processes of dielectric relaxation and viscous flow were determined by using Eyring's rate theory. From relaxation time behaviour of amides in non-polar solvent, solute-solvent and solute-solute type of molecular association is proposed.

  15. Improvements in and environmental applications of double-vial radiorespirometry for the study of microbial mineralization

    International Nuclear Information System (INIS)

    McKinley, V.L.; Federle, T.W.; Vestal, J.R.

    1983-01-01

    Several variations in the scintillation mixture and the filter paper arrangements for double-vial radiorespirometry were compared. Improved efficiencies (44%) and shorter response times were found by adding wetting agents and methanotic NaOH to the scintillation mixture in the filter paper. The scintillation chemicals used did not contain dioxane and were found to be nontoxic to the test microbiota in this system. Covering the inner reaction vial with aluminum foil minimized the reduction in counting efficiency when testing colored or dense environmenal samples. Mineralization rates were determined with 14 C-labeled glucose, acetate, and glutamate and [ 14 C]cellulose- and [ 14 C]lignin-labeled lignocellulose for composting cow manure, forest soil, and arctic lake sediment microbiota. This improved method can be used in a variety of procedures involving the measurement of microbial mineralizations of organic compounds. Since no liquid scintillation cocktail is used for counting, the radioactive wastes are aqueous or can be incinerated, making disposal easy

  16. Synthesis, physical-chemical and biological properties of 1.8-disubstituted of theobromine. V. 8-Benzylidenhydrazino-1-p-methylbenzyltheobromines

    Directory of Open Access Journals (Sweden)

    D. G. Ivanchenko

    2015-10-01

    Full Text Available The problem of searching biologically active compounds amidst xanthine derivatives is a crucial one and is an issue for long-term investigation. Aim. In order to find new biologically active compounds among xanthine derivatives, undescribed earlier 8-benzylidenhydrazino-1-p-methylbenzyltheobromines have been synthesized. Methods and results. Reaction of 1-p-methylbenzyl-8-bromoxanthine with the excess of hydrazine hydrate in the aqueous dioxane is implemented through formation of 8-hydrazine-1(4-methylbenzyltheobromine. Through the interaction of 8-hydrazinetheobromine with aldehydes in aqueous propan-2-ol respective 8-benzylidenhydrazino-1-p-methylbenzyltheobromines have been obtained. Structure of synthesized compounds has been definitely proved by NMR-spectroscopy. Conclusions. Molecular and pharmacological descriptors of obtained substances have been calculated. The antioxidant activity of the obtained compounds has been explored. Priorities for further search of biologically active compounds in a range of xanthine derivatives have been set out.

  17. Heterocyclic Analogues of Xanthone and Xanthione. 1H-Pyrano[2,3-c:6,5-c]dipyrazol-4(7H-ones and Thiones: Synthesis and NMR Data

    Directory of Open Access Journals (Sweden)

    Wolfgang Holzer

    2010-09-01

    Full Text Available The synthesis of the title compounds is described. Reaction of 1-substituted 2-pyrazolin-5-ones with 5-chloro-1-phenyl-1H-pyrazole-4-carbonyl chloride or 5-chloro-3-methyl-1-phenyl-1H-pyrazole-4-carbonyl chloride, respectively, using calcium hydroxide in refluxing 1,4-dioxane gave the corresponding 4-heteroaroylpyrazol-5-ols, which were cyclized into 1H-pyrano[2,3-c:6,5-c]dipyrazol-4(7H-ones by treatment with K2CO3/DMF. The latter were converted into the corresponding thiones upon reaction with Lawesson’s reagent. Detailed NMR spectroscopic investigations (1H, 13C, 15N of the ring systems and their precursors are presented.

  18. Bonded exciplex formation: electronic and stereoelectronic effects.

    Science.gov (United States)

    Wang, Yingsheng; Haze, Olesya; Dinnocenzo, Joseph P; Farid, Samir; Farid, Ramy S; Gould, Ian R

    2008-12-18

    As recently proposed, the singlet-excited states of several cyanoaromatics react with pyridine via bonded-exciplex formation, a novel concept in photochemical charge transfer reactions. Presented here are electronic and steric effects on the quenching rate constants, which provide valuable support for the model. Additionally, excited-state quenching in poly(vinylpyridine) is strongly inhibited both relative to that in neat pyridine and also to conventional exciplex formation in polymers, consistent with a restrictive orientational requirement for the formation of bonded exciplexes. Examples of competing reactions to form both conventional and bonded exciplexes are presented, which illustrate the delicate balance between these two processes when their reaction energetics are similar. Experimental and computational evidence is provided for the formation of a bonded exciplex in the reaction of the singlet excited state of 2,6,9,10-tetracyanoanthracene (TCA) with an oxygen-substituted donor, dioxane, thus expanding the scope of bonded exciplexes.

  19. Preparation of amidoxime-fiber adsorbents based on poly(methacrylonitrile) for recovery of uranium from seawater

    International Nuclear Information System (INIS)

    Kabay, N.

    1994-01-01

    Polymerization of methacrylonitrile was performed with anionic initiators as reported in the literature. The molecular weight of the polymer produced using BuLi as initiator at 0 ± 2 degrees C was on the order of 10 5 . Maximum conversion was 97% with BuLi initiator. For comparison, methacrylonitrile was polymerized with diethylmagnesium in dioxane at 70 degrees C. High-molecular weight polymers with 50-60% conversions were produced by diethylmagnesium initiator. The polymethacrylonitrile obtained by BuLi initiator was used for the fiber production process. The conversion of nitrile was performed by treatment with 3% NH 2 OH in MeOH at 80 degrees C. The amidoxime-fiber adsorbent gave a large adsorption rate, such as 176 μg of U/g of adsorbent/day, in a batchwise seawater adsorption test. 36 refs., 1 fig., 3 tabs

  20. Reference value standards and primary standards for pH measurements in D2O and aqueous-organic solvent mixtures: new accessions and assessments

    International Nuclear Information System (INIS)

    Mussini, P.R.; Mussini, T.; Rondinini, S.

    1997-01-01

    Recommended Reference Value Standards based on the potassium hydro-genphthalate buffer at various temperatures are reported for pH measurements in various binary solvent mixtures of water with eight organic solvents: methanol, ethanol, 2-propanol, 1,2-ethanediol, 2-methoxyethanol (''methylcellosolve''), acetonitrile, 1,4-dioxane, and dimethyl sulfoxide, together with Reference Value Standard based on the potassium deuterium phthalate buffer for pD measurements in D 2 O. In addition are reported Primary Standards for pH based on numerous buffers in various binary solvent mixtures of water with methanol, ethanol, and dimethyl sulfoxide, together with Primary Standards for pD in D 2 O based on the citrate, phosphate and carbonate buffers. (author)

  1. Molar extinction coefficients of some commonly used solvents

    International Nuclear Information System (INIS)

    Kumar, Ashok; Singh, Sukhpal; Singh Mudahar, Gurmel; Singh Thind, Kulwant

    2006-01-01

    Molar extinction coefficients of some commonly used solvents (ethanol (C 2 H 5 OH), methanol (CH 3 OH), propanol (C 3 H 7 OH), butanol (C 4 H 9 OH), water (H 2 O), toluene (C 7 H 8 ), benzene (C 6 H 6 ), carbontetrachloride (CCl 4 ), acetonitrile (C 4 H 3 N), chlorobenzene (C 6 H 5 Cl), diethylether (C 4 H 1 O) and dioxane (C 4 H 8 O 2 )) have been determined by a well-collimated narrow beam transmission geometry at 279, 356, 662, 1173, 1252 and 1332 keV γ rays. The total γ ray interaction cross sections of these solvents have also been determined. A good agreement has been obtained between the experimental results with the theoretical values evaluated through XCOM calculations

  2. A preliminary study on the thermal conductivity and flammability of WPC based on some tropical woods

    International Nuclear Information System (INIS)

    Chia, L.H.L.; Chua, P.H.; Lee, E.E.N.

    1985-01-01

    Selected local woods and their wood-polymer combinations or composites (WPC) were tested for their thermal conductivity and their fire resistance. WPC were prepared by polymerizing monomers 'in situ' in oven dried woods by gamma radiation. The monomers included acrylonitrile (AN), 60% styrene-40% acrylonitrile (STAN), methyl methacrylate (MMA), 95% methyl methacrylate-5% dioxane (MD), and vinylidene chloride (VDC). A reduction in thermal conductivity was exhibited by all the composites prepared. W-PAN showed the greatest reduction in thermal conductivity and W-PSTAN in general showed the least. An explanation is suggested for this behaviour. The polymers PMMA and PMD were found to enhance flammability of the woods while PVDC, PAN, and PSTAN imparted fire resistance to the woods. Of the six local woods studied, Ramin-and-Keruing-polymer composites showed the highest flammable tendencies obtained. The correlation of thermal conductivity to flammability is discussed. (author)

  3. PET studies of potential chemotherapeutic agents: Pt. 10; Synthesis of ''no-carrier-added'' ( sup 11 C)-HECNU: the hydroxyethyl analog of the chemotherapeutic agent BCNU

    Energy Technology Data Exchange (ETDEWEB)

    Conway, T.; Diksic, M. (Montreal Neurological Inst. and Hospital, PQ (Canada). McConnell Brain Imaging Centre McGill Univ., Montreal, PQ (Canada). Dept. of Neurology and Neurosurgery)

    1991-01-01

    Carbon-11-labeled HECNU (1-(2-chloroethyl)-1-nitroso-3-(2-hydroxyethyl) urea) a potential chemotherapeutic agent, has been prepared by the nitrosation of the corresponding carbon-11-labeled urea, HECU, (1-(2-chloroethyl)-3-(2-hydroxyethyl) urea). The isomeric byproduct of nitrosation, 1-(2-chloroethyl)-3-nitroso-3-(2-hydroxyethyl) urea can be efficiently removed by preparative scale HPLC on a Partisil column. ({sup 11}C)-HECU was prepared by reacting ethanolamine with ({sup 11}C)-2-chloroethyl-isocyanate which was itself prepared by reacting ({sup 11}C)-phosgene with 2-chloroethylamine hydrochloride suspended in dioxane at 60-65{sup o}C. This synthesis yielded ({sup 11}C)-HECNU with an average radiochemical purity of 98% in an average radiochemical yield of 18% relative to the radioactivity measured at the end of the {sup 11}C-phosgene introduction. (author).

  4. PET studies of potential chemotherapeutic agents: Pt. 10

    International Nuclear Information System (INIS)

    Conway, T.; Diksic, M.; McGill Univ., Montreal, PQ

    1991-01-01

    Carbon-11-labeled HECNU [1-(2-chloroethyl)-1-nitroso-3-(2-hydroxyethyl) urea] a potential chemotherapeutic agent, has been prepared by the nitrosation of the corresponding carbon-11-labeled urea, HECU, [1-(2-chloroethyl)-3-(2-hydroxyethyl) urea]. The isomeric byproduct of nitrosation, 1-(2-chloroethyl)-3-nitroso-3-(2-hydroxyethyl) urea can be efficiently removed by preparative scale HPLC on a Partisil column. ( 11 C)-HECU was prepared by reacting ethanolamine with ( 11 C)-2-chloroethyl-isocyanate which was itself prepared by reacting ( 11 C)-phosgene with 2-chloroethylamine hydrochloride suspended in dioxane at 60-65 o C. This synthesis yielded ( 11 C)-HECNU with an average radiochemical purity of 98% in an average radiochemical yield of 18% relative to the radioactivity measured at the end of the 11 C-phosgene introduction. (author)

  5. Preparation and LSC Standardization of ''89Sr (DNP) Using the CIEMAT/NIST Method

    International Nuclear Information System (INIS)

    Rodriguez Barquero, L.; Los Arcos Merino, J. M.; Grau Malonda, A.

    1994-01-01

    A procedure for preparation of liquid scintillation counting samples of the strontium DNP complex, labelled with ''89Sr, is described, the chemical quench, the counting stability and spectral evolution of this compound is studied in six scintillators, Toluene, Toluene-alcohol, Dioxane-naphthalene, HiSafe II, Ultima- Gold and Instagel. The liquid scintillation standardization of 89Sr-DNP by the CIEMAT/NIST method, using HiSafe II and Ultima-Gold scintillators, has been carried out. The discrepancies between experimental and computed efficiencies are lower than 0.38% and 0.48%, respectively. The solution has been standardized in terms of activity concentration to an overall uncertainty of 0,38%. (Author) 10 refs

  6. Synthesis and in Vitro Antifungal Activity against Botrytis cinerea of Geranylated Phenols and Their Phenyl Acetate Derivatives

    Science.gov (United States)

    Chávez, María I.; Soto, Mauricio; Taborga, Lautaro; Díaz, Katy; Olea, Andrés F.; Bay, Camila; Peña-Cortés, Hugo; Espinoza, Luis

    2015-01-01

    The inhibitory effects on the mycelial growth of plant pathogen Botritys cinerea have been evaluated for a series of geranylphenols substituted with one, two and three methoxy groups in the aromatic ring. The results show that the antifungal activity depends on the structure of the geranylphenols, increasing from 40% to 90% by increasing the number of methoxy groups. On the other hand, the acetylation of the –OH group induces a change of activity that depends on the number of methoxy groups. The biological activity of digeranyl derivatives is lower than that exhibited by the respective monogeranyl compound. All tested geranylphenols have been synthesized by direct coupling of geraniol and the respective phenol. The effect of solvent on yields and product distribution is discussed. For monomethoxyphenols the reaction gives better yields when acetonitrile is used as a solvent and AgNO3 is used as a secondary catalyst. However, for di- and trimethoxyphenols the reaction proceeds only in dioxane. PMID:26287171

  7. New phenanthrene and 9, 10-dihydrophenanthrene derivatives from the stems of Dendrobium officinale with their cytotoxic activities.

    Science.gov (United States)

    Zhao, Gui-Yun; Deng, Bo-Wen; Zhang, Chong-Yu; Cui, Yi-Da; Bi, Jia-Yi; Zhang, Guo-Gang

    2018-01-01

    Two new phenanthrene and 9, 10-dihydrophenanthrene derivatives (1-2) with six known congeners (3-8) were isolated from the extraction of stems of Dendrobium officinale. Compounds 1 and 2 were based on carbon skeleton in which phenanthrene and 9, 10-dihydrophenanthrene moiety were linked with a phenylpropane unit through a dioxane bridge, respectively. Their structures were determined by comprehensive NMR spectroscopic data, the absolute configuration of new compounds were determined by comparing their experimental and calculated ECD for the first time. All the compounds were investigated contains two cancer cell lines (HI-60, THP-1). All the isolates showed cytotoxicity, especially compound 4 showed markedly cytotoxic activities against HI-60 and THP-1 cell lines with IC 50 values of 11.96 and 8.92 μM.

  8. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-((1H-benzimidazol-2-yl-methylene) amino) phenol

    Energy Technology Data Exchange (ETDEWEB)

    Omprakash, K L; Chandra Pal, A V; Reddy, M L.N. [Osmania Univ., Hyderabad (India). Dept. of Chemistry

    1982-03-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO/sub 4/) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (log..beta../sub 2/) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III).

  9. Formation constants of binary complexes of lanthanides with 2-hydroxymethyl-benzimidazole

    Energy Technology Data Exchange (ETDEWEB)

    Nagendram, A; Omprakash, K L; Chandra Pal, A V; Reddy, M L.N.

    1988-03-01

    Proton-ligand and metal-ligand formation constants of binary complexes of La(III), Pr(III), Nd(III), Gd(III), Dy(III) and Y(III) with 2-hydroxymethylbenzimidazole have been determined pH-metrically in 50 per cent v/v aq dioxane medium at 30deg, 40deg and 50degC and I=0.1 M (NaClO/sub 4/). The theromdynamic parameters of complex formation have been evaluated. Stabilities (log ..beta../sub 2/ values) of the chelates increase with decrease in ionic radius of the metal (Dy(III) > Gd(III) > Y(III) > Nd(III) > Pr(III) > La(III)). (author). 7 refs.

  10. Effects of hydroxylated benzaldehyde derivatives on radiation-induced reactions involving various organic radicals

    Science.gov (United States)

    Ksendzova, G. A.; Samovich, S. N.; Sorokin, V. L.; Shadyro, O. I.

    2018-05-01

    In the present paper, the effects of hydroxylated benzaldehyde derivatives and gossypol - the known natural occurring compound - on formation of decomposition products resulting from radiolysis of ethanol and hexane in deaerated and oxygenated solutions were studied. The obtained data enabled the authors to make conclusions about the effects produced by the structure of the compounds under study on their reactivity towards oxygen- and carbon-centered radicals. It has been found that 2,3-dihydroxybenzaldehyde, 4,6-di-tert-butyl-2,3-dihydroxybenzaldehyde and 4,6-di-tert-butyl-3-(1,3-dioxane-2-yl)-1,2-dihydroxybenzene are not inferior in efficiency to butylated hydroxytoluene - the industrial antioxidant - as regards suppression of the radiation-induced oxidation processes occurring in hexane. The derivatives of hydroxylated benzaldehydes were shown to have a significant influence on radiation-induced reactions involving α-hydroxyalkyl radicals.

  11. Spectrophotometric determination of fluoride with alizarin complexone

    Energy Technology Data Exchange (ETDEWEB)

    Marczenko, Z; Lenarczyk, L [Politechnika Warszawska (Poland)

    1976-01-01

    The modification of direct spectrophotometric method of fluoride determination by alizarin complexone has been developed. It was shown that the lanthanum alizarin complexone chelate is more convenient than that of cerium (3). The influence of acetone, dioxane and dimethyl sulphoxide in water solution on the increase of sensitivity of the method and the rate of colour reaction has been determined. The optimal pH ranges for the reaction with lanthanum and cerium (3) have been estimated. Some amines having a large molecule are useful for extraction of blue fluoride complex with isobutanol. Dioctylamine was applied in a new extraction spectrophotometric procedure of fluoride determination. Conditions in reagent have been established. Both variants of the method have been applied to the fluoride determination in several chemicals. The obtained results show a good precision and accuracy.

  12. The disposal of radioactive solvent waste

    International Nuclear Information System (INIS)

    Dean, B.; Baker, W.T.

    1976-01-01

    As the use of radioisotope techniques increases, laboratories are faced with the problem of disposing of considerable quantities of organic solvent and aqueous liquid wastes. Incineration or collection by a waste contractor both raise problems. Since most of the radiochemicals are preferentially water soluble, an apparatus for washing the radiochemicals out into water and discharging into the normal drainage system in a high diluted form is described. Despite the disadvantages (low efficiency, high water usuage, loss of solvent in presence of surface active agents, precipitation of phosphors from dioxan based liquids) it is felt that the method has some merit if a suitably improved apparatus can be designed at reasonable cost. (U.K.)

  13. 18-Membered cyclic esters derived from glycolide and lactide: preparations, structures and coordination to sodium ions

    Energy Technology Data Exchange (ETDEWEB)

    Chisholm, Malcolm H.; Gallucci, Judith C.; Yin, Hongfeng (OSU)

    2008-06-30

    From reactions between glycolide or lactide (4 equiv.) with 4-dimethylaminopyridine, DMAP (1 equiv.) and NaBPh4 (1 equiv.) in benzene at 70 C the cyclic ester adducts (CH{sub 2}C(O)O){sub 6}NaBPh{sub 4} and (CHMeC(O)O){sub 6}NaBPh{sub 4} are formed respectively. The structures of the salts Na[(S,R,S,R,S,R)-(CH{sub 3}CHC(O)O){sub 6}]{sub 2}BPh{sub 4} {center_dot} CH{sub 3}CN and (CH{sub 2}C(O)O){sub 6}NaBPh{sub 4} {center_dot} (CH{sub 3}CN){sub 2} are reported. The cyclic esters were separated by chromatography and the structures of (CH{sub 2}C(O)O){sub 6}, (S,R,R,R,R,R)-(CHMeC(O)O){sub 6} and (S,S,R,R,R,R)-(CHMeC(O)O){sub 6} were determined. The {sup 1}H and {sup 13}C NMR data are reported for one of each of the six enantiomers of (CHMeC(O)O){sub 6} and the two meso isomers. The mechanism for the formation of these 18-membered rings is discussed in terms of an initial reaction between DMAP and NaBPh{sub 4} in hot benzene that produces NaPh and DMAP:BPh{sub 3} in the presence of the monomer lactide. The cyclic esters (CHMeC(O)O){sub 6} can also be obtained from the reaction between polylactide, PLA, in the presence of DMAP and NaBPh{sub 4}. The cyclic esters 3-methyl-1,4-dioxane-2,5-dione and 3,6,6-trimethyl-1,4-dioxane-2,5-dione undergo similar ring enlarging reactions to give cyclic 18-membered ring esters as determined by ESI-MS.

  14. Polymer scaffolds with no skin-effect for tissue engineering applications fabricated by thermally induced phase separation

    International Nuclear Information System (INIS)

    Kasoju, Naresh; Kubies, Dana; Sedlačík, Tomáš; Kumorek, Marta M.; Rypáček, František; Janoušková, Olga; Koubková, Jana

    2016-01-01

    Thermally induced phase separation (TIPS) based methods are widely used for the fabrication of porous scaffolds for tissue engineering and related applications. However, formation of a less-/non-porous layer at the scaffold’s outer surface at the air–liquid interface, often known as the skin-effect, restricts the cell infiltration inside the scaffold and therefore limits its efficacy. To this end, we demonstrate a TIPS-based process involving the exposure of the just quenched poly(lactide-co-caprolactone):dioxane phases to the pure dioxane for a short time while still being under the quenching strength, herein after termed as the second quenching (2Q). Scanning electron microscopy, mercury intrusion porosimetry and contact angle analysis revealed a direct correlation between the time of 2Q and the gradual disappearance of the skin, followed by the widening of the outer pores and the formation of the fibrous filaments over the surface, with no effect on the internal pore architecture and the overall porosity of scaffolds. The experiments at various quenching temperatures and polymer concentrations revealed the versatility of 2Q in removing the skin. In addition, the in vitro cell culture studies with the human primary fibroblasts showed that the scaffolds prepared by the TIPS based 2Q process, with the optimal exposure time, resulted in a higher cell seeding and viability in contrast to the scaffolds prepared by the regular TIPS. Thus, TIPS including the 2Q step is a facile, versatile and innovative approach to fabricate the polymer scaffolds with a skin-free and fully open porous surface morphology for achieving a better cell response in tissue engineering and related applications. (paper)

  15. RAFT Dispersion Alternating Copolymerization of Styrene with N-Phenylmaleimide: Morphology Control and Application as an Aqueous Foam Stabilizer

    Science.gov (United States)

    2016-01-01

    We report a new nonaqueous polymerization-induced self-assembly (PISA) formulation based on the reversible addition–fragmentation chain transfer (RAFT) dispersion alternating copolymerization of styrene with N-phenylmaleimide using a nonionic poly(N,N-dimethylacrylamide) stabilizer in a 50/50 w/w ethanol/methyl ethyl ketone (MEK) mixture. The MEK cosolvent is significantly less toxic than the 1,4-dioxane cosolvent reported previously [YangP.; Macromolecules2013, 46, 8545−8556]. The core-forming alternating copolymer block has a relatively high glass transition temperature (Tg), which leads to vesicular morphologies being observed during PISA, as well as the more typical sphere and worm phases. Each of these copolymer morphologies has been characterized by transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS) studies. TEM studies reveal micrometer-sized elliptical particles with internal structure, with SAXS analysis suggesting an oligolamellar vesicle morphology. This structure differs from that previously reported for a closely related PISA formulation utilizing a poly(methacrylic acid) stabilizer block for which unilamellar platelet-like particles are observed by TEM and SAXS. This suggests that interlamellar interactions are governed by the nature of the steric stabilizer layer. Moreover, using the MEK cosolvent also enables access to a unilamellar vesicular morphology, despite the high Tg of the alternating copolymer core-forming block. This was achieved by simply conducting the PISA synthesis at a higher temperature for a longer reaction time (80 °C for 24 h). Presumably, MEK solvates the core-forming block more than the previously utilized 1,4-dioxane cosolvent, which leads to greater chain mobility. Finally, preliminary experiments indicate that the worms are much more efficient stabilizers for aqueous foams than either the spheres or the oligolamellar elliptical vesicles. PMID:27708458

  16. Retinoid quantification by HPLC/MS(n)

    Science.gov (United States)

    McCaffery, Peter; Evans, James; Koul, Omanand; Volpert, Amy; Reid, Kevin; Ullman, M. David

    2002-01-01

    Retinoic acid (RA) mediates most of the biological effects of vitamin A that are essential for vertebrate survival. It acts through binding to receptors that belong to the nuclear receptor transcription factor superfamily (Mangelsdorf et al. 1994). It is also a highly potent vertebrate teratogen. To determine the function and effects of endogenous and exogenous RA, it is important to have a highly specific, sensitive, accurate, and precise analytical procedure. Current analyses of RA and other retinoids are labor intensive, of poor sensitivity, have limited specificity, or require compatibility with RA reporter cell lines (Chen et al. 1995. BIOCHEM: Pharmacol. 50: 1257-1264; Creech Kraft et al. 1994. BIOCHEM: J. 301: 111-119; Lanvers et al. 1996. J. Chromatogr. B Biomed. Appl. 685: 233-240; Maden et al. 1998. DEVELOPMENT: 125: 4133-4144; Wagner et al. 1992. DEVELOPMENT: 116: 55-66). This paper describes an HPLC/mass spectrometry/mass spectrometry product ion scan (HPLC/MS(n)) procedure for the analysis of retinoids that employs atmospheric pressure chemical ionization MS. The retinoids are separated by normal-phase column chromatography with a linear hexane-isopropanol-dioxane gradient. Each retinoid is detected by a unique series of MS(n) functions set at optimal collision-induced dissociation energy (30% to 32%) for all MS(n) steps. The scan events are divided into three segments, based on HPLC elution order, to maximize the mass spectrometer duty cycle. The all-trans, 9-cis, and 13-cis RA isomers are separated, if desired, by an isocratic hexane-dioxane-isopropanol mobile phase. This paper describes an HPLC/MS(n) procedure possessing high sensitivity and specificity for retinoids.

  17. Thermodynamic functions for solubility of 3-nitro-o-toluic acid in nine organic solvents from T = (283.15 to 318.15) K and apparent thermodynamic properties of solutions

    International Nuclear Information System (INIS)

    Li, Xinbao; Wang, Mingju; Du, Cunbin; Cong, Yang; Zhao, Hongkun

    2017-01-01

    Highlights: • Solubilities of 3-nitro-o-toluic acid in nine organic solvents were determined. • The solubilities were correlated by using four thermodynamic models. • The mixing properties of solution were computed based on Wilson model. - Abstract: Separation of 3-nitro-o-toluic acid from its isomeric mixtures has essential significance in industry. In this work, by using isothermal saturation method, the solid-liquid equilibrium for 3-nitro-o-toluic acid in nine organic solvents (acetonitrile, methanol, ethanol, n-propanol, isopropanol, ethyl acetate, acetone, 1,4-dioxane and 2-butanone) were obtained experimentally within a temperature range from (283.15 to 318.15) K under atmosphere pressure of 101.2 kPa, and the solubility values of 3-nitro-o-toluic acid in these solvents were determined by a high-performance liquid chromatography. Within the studied temperature range, the mole fraction solubility of 3-nitro-o-toluic acid in selected organic solvents increased with increasing temperature. Except for ethyl acetate, the descending order of the mole fraction solubility values were as follow: 1,4-dioxane > acetone > 2-butanone > methanol > ethanol > isopropanol > n-propanol > acetonitrile. The solubility values determined for 3-nitro-o-toluic acid in the selected solvents were correlated and back calculated with the modified Apelblat equation, λh equation, Wilson model and NRTL model. The largest values of RAD and RMSD obtained with the four models were 0.67% and 4.02 × 10 −4 , respectively. In general, the four thermodynamic models were all acceptable for describing the solubility behaviour of 3-nitro-o-toluic acid in these solvents. In addition, the apparent mixing Gibbs energy, mixing enthalpy, mixing entropy, activity coefficient at infinitesimal concentration and reduced excess enthalpy were calculated. The acquired solubility data and thermodynamic studies would be very important in optimizing the separation process of 3-nitro-o-toluic acid from

  18. Long Range Polymer Chain Dynamics of Highly Flexible Polysiloxane in Solution Probed by Pyrene Excimer Fluorescence

    Directory of Open Access Journals (Sweden)

    Janine L. Thoma

    2018-03-01

    Full Text Available A poly(dimethylsiloxane-co-(3-aminopropylmethylsiloxane polymer (PDMS with 20.3 mol % of (3-aminopropylmethyl siloxane monomer has been labeled randomly with 1-pyreneacetyl groups to generate a series of polysiloxanes (Py-PDMS with pyrenyl contents ranging from 0.7 mol % to 5.2 mol % of the total number of structural units. The remainder of the amino groups were acetylated to avoid intra-chain quenching of the excited singlet states of pyrene via exciplex formation with free amino groups while allowing the formation of excimers to proceed. The fluorescence spectra and temporal decays of the Py-PDMS samples were acquired in tetrahydrofuran (THF, N,N-dimethylformamide (DMF, and dioxane. blob, the average rate constant for intra-chain pyrene excimer formation, was determined from the analysis of the fluorescence decays. blob was found to equal 1.16 (±0.13 × 109, 1.14 (±0.12 × 109, and 0.99 (±0.10 × 109 s−1 in THF, DMF, and dioxane, respectively, at room temperature. They are the largest values found to date for any polymeric backbone in these solvents. The qualitative relationship found here between blob and the chemical structures of the polymers indicates that the luminescence characteristics of randomly labeled polymers is a very useful method to probe the long range dynamics of chains of almost any polymer that is amenable to substitution by a lumophore.

  19. Measurement of the quantity of water in organic solvents by infrared absorption an measurement of the dielectric constants; Dosage de l'eau dans les solvants organiques par absorption infra-rouge et mesure des constantes dielectriques

    Energy Technology Data Exchange (ETDEWEB)

    Desnoyer, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1959-06-15

    Some chemical methods for the analysis of the quantity of water in solvents are first described, their object being the determination of the maximum error for cases where the water content is less than 1 per cent. - The first part of the work consists in describing infrared spectrometry as applied to the analysis of water in carbon tetrachloride, chloroform aniline, acetone and dioxane. A method based on isotopic exchange between heavy and light water is used on the one hand for determining the solubility of water in carbon tetrachloride and on the other hand for establishing standard solutions (sensitivity of the method). - In the second part the dielectric constant of water solvent solutions is measured. A table is presented giving the precision obtained by the two principal methods. These are comparable and further than that the appearance of the spectra suggests an interpretation of the anomalies observed in calibration curves obtained by the dielectric constant method. (author) [French] Quelques methodes chimiques d'analyses de l'eau dissoute dans les solvants sont decrites tout d'abord en vue de determiner l'erreur maxima dans le cas ou la teneur en eau ne depasse pas 1 pour cent. - Une premiere partie du travail expose la technique utilisee en spectrometrie infrarouge pour doser l'eau dans le tetrachlorure de carbone, chloroforme, aniline, acetone et le dioxane. Une methode basee sur l'echange isotopique entre l'eau legere et l'eau lourde permet de determiner d'une part la solubilite de l'eau dans le tetrachlorure de carbone et le chloroforme et d'autre part le titre en valeur absolue des solutions etalons (sensibilite de la methode). - Dans une deuxieme partie, on mesure la constante dielectrique des solutions eau-solvant. On dresse un tableau des precisions obtenues par les deux methodes principales. Celles-ci sont comparables et en outre, l'aspect du spectre suggere une interpretation des anomalies observees dans les courbes d'etalonnage tracees par la

  20. Assessment of potential aluminum chelators in an octanol/aqueous system and in the aluminum-loaded rabbit.

    Science.gov (United States)

    Yokel, R A; Kostenbauder, H B

    1987-11-01

    Aluminum (Al) solubilization from Al borate and its distribution in an octanol/aqueous system (Do/w) were determined in the absence and presence of 12 potential Al chelators. Citrate, N,N'-bis-(2-hydroxybenzyl)ethylenediamine- N,N'-diacetic acid (HBED), cyclohexane-1,2-diaminotetraacetic acid (CDTA), diethylenetriaminepentaacetic acid (DTPA), nitrilotriacetic acid (NTA), desferrioxamine, and ethylenediamine-N,N'-bis(2-dihydroxyphenylacetic acid) (EDDHA) were 55 to over 100% efficient in solubilizing equimolar amounts of Al. Tetracycline, EDTA, and 2,3-dihydroxybenzoic acid (DHBA) were less than 20% efficient. 1,4-Dioxane and fluoride were ineffective. The Do/w of Al averaged 0.005. The Do/w of the Al.chelator complex was generally less than that of Al, except for HBED and tetracycline (0.04 and 0.96, respectively). The Do/w of DHBA, desferrioxamine, EDDHA, and HBED were not influenced by Al, but tetracycline became more lipophilic. These compounds were tested for their ability to increase urinary Al excretion in Al-loaded rabbits. Chelators were given po weekly beginning 2 weeks after Al loading. Urine was obtained hourly from 3 hr prior to 6 hr after chelator administration and analyzed for Al. Fluoride and tetracycline (450 and 4500 mumol/kg) and citrate, NTA, EDTA, CDTA, DTPA, DHBA, HBED, and 1,4-dioxane (150 and 1500 mumol/kg) were ineffective. Following HBED administration, some of the Al-loaded rabbits died, presumably due to redistribution of Al within the rabbit. Following DTPA administration, some of the Al-loaded rabbits died, presumably due to DTPA. Oral EDDHA (1500 mumol/kg) significantly increased urinary Al excretion. EDDHA and desferrioxamine (150 mumol/kg) were administered by po, sc, and iv routes and were found to have comparable potency. The in vitro results may explain some of the in vivo findings. The in vitro methods may be useful to screen out compounds with no chelation potential. EDDHA-like compounds may have potential as alternatives to

  1. Solubility and solution thermodynamics of 2-methyl-6-nitroaniline in ten organic solvents at elevated temperatures

    International Nuclear Information System (INIS)

    Cong, Yang; Wang, Jian; Du, Cunbin; Han, Shuo; Zhao, Hongkun

    2016-01-01

    Highlights: • Solubility of 2-methyl-6-nitroaniline in ten solvents were determined. • The solubility were correlated with four thermodynamic models. • Standard dissolution enthalpy and excess enthalpy of the solutions were computed. - Abstract: Knowledge of solubility for 2-methyl-6-nitroaniline in different solvents is essential for its purification and further theoretical studies. In this paper, the solid-liquid equilibrium for 2-methyl-6-nitroaniline in ten pure organic solvents (methanol, ethanol, n-propanol, isopropanol, toluene, ethyl acetate, acetonitrile, acetone, cyclohexane and 1,4-dioxane) was established using the isothermal saturation method at temperatures T = (278.15–313.15) K under pressure of 101.2 kPa, and the solubility of 2-methyl-6-nitroaniline in these solvents were determined by a high-performance liquid chromatography (HPLC). In general, the mole fraction solubility followed the following order from high to low in different solvents: 1,4-dioxane (0.1799–0.3390) > acetone (0.1128–0.3010) > ethyl acetate (0.08414–0.2654) > acetonitrile (0.04179–0.2027) > toluene (0.02367–0.1104) > n-propanol (0.01080–0.04514) > ethanol (0.01020–0.04202) > isopropanol (0.008595–0.03763) > methanol (0.007391–0.03198) > cyclohexane (0.001027–0.005617). The modified Apelblat equation, λh equation, Wilson model and NRTL model were employed to correlate the measured solubility data of 2-methyl-6-nitroaniline in the selected solvents. Results indicated that the largest values of RAD and RMSD acquired by the four models were less than 0.76% and 9.13 × 10"−"4, respectively. The modified Apelblat equation provided better results than the other three models. Furthermore, the standard dissolution enthalpy and excess enthalpy of the solutions were computed from the solubility values. The standard dissolution enthalpies vary within the range from (14.88 to 45.57) kJ·mol"−"1 and are all positive, the dissolution process of 2-methyl-6

  2. Fluorophore appended saccharide cyclophane: self-association, fluorescent properties, heterodimers with cyclodextrins, and cross-linking behavior with peanut agglutinin of dansyl-modified saccharide cyclophane.

    Science.gov (United States)

    Hayashida, Osamu; Hamachi, Itaru

    2004-05-14

    A saccharide cyclophane bearing an environment-sensitive fluorophore (1) was prepared by introducing not only three branches with a terminal galactose residue but also one with a dansyl moiety into a tetraaza[6.1.6.1]paracyclophane skeleton. Self-association behavior of the dansyl-appended saccharide cyclophane was characterized in aqueous media by fluorescence spectroscopy and dynamic light scattering measurements. At least in the concentrations below 1.0 x 10(-5) M, saccharide cyclophane 1 existed in a monomeric state, whereas it tended to form self-aggregated complexes in the higher concentration. Solvent polarity dependency on the emission spectra of 1 was examined by fluorescence spectroscopy. With increasing dioxane contents in dioxane/water solvents, the fluorescence intensity originating from the dansyl moiety of 1 increased along with a concomitant blue shift of the fluorescence maximum (lambda(em)). In the monomeric state of 1 in water, the dansyl moiety of 1 was not fully included into its cyclophane cavity but partially exposed to the bulk aqueous phase. In the higher concentration ranges in an aggregate state, however, the dansyl group of 1 was located in the apolar cyclophane cavity whose microenvironment was equivalent to the polarity of 1-butanol evaluated on the basis of a correlation between lambda(em) and solvent polarity. This indicates an intermolecular inclusion of the dansyl moiety within the cyclophane. When cyclodextrin (CD) was mixed with 1, the dansyl group of 1 was bound to an internal cavity of CD such as gamma-CD, beta-CD, 6-O-alpha-glucosyl-beta-CD, and 6-O-alpha-maltosyl-beta-CD with binding constants of 7.5 x 10(2), 7.8 x 10(2), 7.7 x 10(2), and 6.0 x 10(2) M(-1), respectively. Such a supramolecular assembling of dansyl-modified cyclophane 1 and CDs caused changes of the fluorescence spectra as well as appearance of induced CD bands in aqueous media. Furthermore, saccharide cyclophane 1 was selectively bound to peanut agglutinin

  3. Surface recognition and fluorescence sensing of histone by dansyl-appended cyclophane-based resorcinarene trimer.

    Science.gov (United States)

    Hayashida, Osamu; Ogawa, Naoyuki; Uchiyama, Masaki

    2007-11-07

    A cyclophane-based resorcinarene trimer (3) bearing a dansyl moiety as an environmentally sensitive fluorophore was prepared by stepwise condensation of a tetraaza[6.1.6.1]paracyclophane skeleton with a dansyl moiety and three resorcinarene derivatives having heptacarboxylic acid residues in this sequence. The dansyl-appended cyclophane exhibited the following fluorescence properties regarding solvent polarity dependency and histone surface recognition: With increasing dioxane contents in dioxane/water solvents, the fluorescence intensity originating from the dansyl moiety of 3 increased along with a concomitant blue shift of the fluorescence maximum (lambdaem). The microenvironmentally sensitive fluorescence properties of dansyl fluorophore were maintained, even when the dansyl moiety was covalently attached to a cyclophane. Most interestingly, the cyclophane-based resorcinarene trimer exhibited recognition and fluorescence sensing capabilities toward histone, a small basic protein of eukaryotic chromatins. The fluorescence intensity originating from 3 increased along with a concomitant blue shift of lambdaem upon the addition of histone, reflecting the formation of 3-histone complexes. A relatively large fluorescence polarization (P) value was obtained for the 3-histone complexes (0.15), reflecting highly restricted conformations of 3, and the obtained P value was much larger than that of 3 alone in aqueous medium (0.07). The binding constant (K) of 3 with histone (unit basis) was estimated to be 2.1 x 106 M-1. On the other hand, upon the addition of acetylated histone (Ac-histone) to an aqueous solution containing 3, the extent of change in fluorescence intensity originating from the dansyl group of 3 was almost negligible, indicating that the electrostatic interactions between 3 and Ac-histone were weak. In addition, the fluorescence spectral changes were also small or negligible upon the addition of other proteins such as albumin, ovalbumin, peanut agglutinin

  4. Synthesis, Characterization and Application of Poly (Styrene-4- Vinyl Pyridine) Membranes Assembled With Single-Wall Carbon Nanotubes

    KAUST Repository

    He, Haoze

    2011-06-01

    Poly(styrene‐4‐vinylpyridine) (PS‐P4VP) isoporous membranes were prepared and their properties were evaluated in this research. The solution was prepared by dissolving PS‐P4VP polymer with necessary additives into a 1:1:1 1,4‐dioxane – N,N‐dimethyl formamide – tetrahydrofuran (DOX‐DMF‐THF, DDT) solvent. Then 0.5‐1.0 mL of the primary solution was cast onto the non‐woven substrate membrane on a glass slide, evaporated for 15‐20 sec and immersed into de‐ionized water for more than 30 min for the solidification of isoporous structure and for the formation of the primary films, which could be post‐processed in different ways for different tests. The membrane surface presents a well‐ordered, hexagonal self‐assembly structure, which is fit for aqueous and gaseous filtration. The pore size of the isoporous surface is 30~40 nm. The pore size is also sensitive to [H+] in the solution and a typical pair of S‐shape pH‐correlation curves with significant hysteresis was found. Four techniques were tried to improve the properties of the membranes in this research: 1) 1,4‐diiodobutane was introduced to chemically change the structure as a cross‐linking agent. 2) single‐wall carbon nanotube (SWCNT) was linked to the membranes in order to strengthen the stability and rigidity and to reduce the hysteresis. 3) Homo‐poly(4‐vinylpyridine) (homo‐P4VP) was added and inserted into the PS‐P4VP micelles to affect the pore size and surface structure. 4) Copper acetate (Cu(Ac)2) was used as substitute of dioxane to prepare the Cu(Ac)2‐DMF‐THF (CDT) mixed solvent, for a better SWCNT dispersion. All the possible improvements were judged by the atomic force microscopy (AFM) images, water and gas flux tests and pH‐correlation curves. The introduction of SWCNT was the most important innovation in this research and is promising in future applications.

  5. Studies in reactive extrusion processing of biodegradable polymeric materials

    Science.gov (United States)

    Balakrishnan, Sunder

    Various reaction chemistries such as Polymerization, Polymer cross-linking and Reactive grafting were investigated in twin-screw extruders. Poly (1,4-dioxan-2-one) (PPDX) was manufactured in melt by the continuous polymerization of 1,4-dioxan-2-one (PDX) monomer in a twin-screw extruder using Aluminum tri-sec butoxide (ATSB) initiator. Good and accurate control over molecular weight was obtained by controlling the ratio of monomer to initiator. A screw configuration consisting of only conveying elements was used for the polymerization. The polymerization reaction was characterized by a monomer-polymer dynamic equilibrium, above the melting temperature of the polymer, limiting the equilibrium conversion to 78-percent. Near complete (˜100-percent) conversion was obtained on co-polymerizing PDX monomer with a few mol-percent (around 8-percent) Caprolactone (CL) monomer in a twin-screw extruder using ATSB initiator. The co-polymers exhibited improved thermal stability with reduction in glass transition temperature. The extruder was modeled as an Axial Dispersed Plug Flow Reactor for the polymerization of CL monomer using Residence Time Distribution (RTD) Analysis. The model provided a good fit to the experimental RTD and conversion data. Aliphatic and aliphatic-aromatic co-polyesters, namely Polycaprolactone (PCL) and Poly butylenes (adipate-co-terephthalate) (Ecoflex) were cross-linked in a twin-screw extruder using radical initiator to form micro-gel reinforced biodegradable polyesters. Cross-linked Ecoflex was further extrusion blended with talc to form blends suitable to be blown into films. A screw configuration consisting of conveying and kneading elements was found to be effective in dispersion of the talc particles (5--10 microns) in the polyester matrix. While the rates of crystallization increased for the talc filled polyester blends, overall crystallinity reduced. Mechanical, tear and puncture properties of films made using the talc filled polyester blends

  6. Application of polymeric macroporous supports for temperature-responsive chromatography of pharmaceuticals.

    Science.gov (United States)

    Lamprou, Alexandros; Gavriilidou, Agni-Faviola-Mika; Storti, Giuseppe; Soos, Miroslav; Morbidelli, Massimo

    2015-08-14

    A macroporous particulate support prepared previously by reactive gelation under shear and functionalized with poly(N-isopropylacrylamide), PNIPAM, brushes of variable length is applied for temperature-responsive chromatography, whereby temperature modulates hydrophobic interactions. Several different analytes, including small pharmaceuticals, peptides, proteins and monoclonal antibodies are employed. Contrary to the most commonly observed behavior in conventional chromatography, increasing retention is observed at elevated temperatures. Peak broadening is quantified using the peak standard deviation, which depends on both the polymer chain conformation and analyte adsorptivity. The favorable effect of grafted polymer thickness on retention becomes progressively less pronounced for thicker grafted PNIPAM layers. The effect of eluent composition on solute-sorbent interactions was investigated by introducing NaCl, methanol, dioxane and by varying the pH. Salt or organic solvent addition affects apart from the analytes solution properties, the hydrophobicity of the stationary phase itself. Frontal analyses performed at different temperatures to determine dynamic binding capacities, indicate small mass transfer resistances imposed by this novel packing material. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Transesterification Synthesis of Chloramphenicol Esters with the Lipase from Bacillus amyloliquefaciens

    Directory of Open Access Journals (Sweden)

    Fengying Dong

    2017-09-01

    Full Text Available This work presents a synthetic route to produce chloramphenicol esters by taking advantage the high enantio- and regio-selectivity of lipases. A series of chloramphenicol esters were synthesized using chloramphenicol, acyl donors of different carbon chain length and lipase LipBA (lipase cloned from Bacillus amyloliquefaciens. Among acyl donors with different carbon chain lengths, vinyl propionate was found to be the best. The influences of different organic solvents, reaction temperature, reaction time, enzyme loading and water content on the synthesis of the chloramphenicol esters were studied. The synthesis of chloramphenicol propionate (0.25 M with 4.0 g L−1 of LipBA loading gave a conversion of ~98% and a purity of ~99% within 8 h at 50 °C in 1,4-dioxane as solvent. The optimum mole ratio of vinyl propionate to chloramphenicol was increased to 5:1. This is the first report of B. amyloliquefaciens lipase being used in chloramphenicol ester synthesis and a detailed study of the synthesis of chloramphenicol propionate using this reaction. The high enzyme activity and selectivity make lipase LipBA an attractive catalyst for green chemical synthesis of molecules with complex structures.

  8. AMEC GEOMATRIX/ARA GROUNDWATER REMEDIAITON TRIP REPORT

    Energy Technology Data Exchange (ETDEWEB)

    SIMMONS SA

    2008-08-07

    City of Rialto, Well No.3 Demonstration System Integration Project, and Baldwin Park Operable Unit, Baldwin Park, California. The groundwater remediation contractors are AMEC Geomatrix and ARA. The sites were visited on July 22, 2008. Fluor Hanford and the U.S. Department of Energy are currently looking at a variety of alternatives to capture carbon tetrachloride, nitrates, and other COCs from 200-ZP-l groundwater. A few of the more important objectives of our visits were to: (1) Evaluate the treatment systems being used by AMEC Geomatrix to address VOCs, perchlorate, NDMA, 1,4,-Dioxane, and 1,2,3 TCP in a drinking water source; (2) Evaluate how effective these treatment methods have been; (3) Determine the types of problems they have encountered with these treatment systems and how they addressed these problems; (4) Determine the types of secondary wastes being generated by the system; (5) Determine how clean of an operation these companies run; and (6) Determine if the site is worth being visited by DOE-RL at a later date.

  9. Comparison of UVC/S2O8 2- with UVC/H2O2 in terms of efficiency and cost for the removal of micropollutants from groundwater

    DEFF Research Database (Denmark)

    Antoniou, Maria; Andersen, Henrik Rasmus

    2015-01-01

    ' concentrations were tested with atrazine alone and in the micropollutants' mixture and it was decided to use 11.8mgL(-1) S2O8(2-) and 14.9mgL(-1) H2O2 for further testing since is closer to industrial applications and to minimize the residual oxidant concentration. Changes of the matrix composition......This study compared the UVC/S2O8(2-) system with the more commonly used AOP in water industry, UVC/H2O2, and examined whether the first one can be an economically feasible alternative technology. Atrazine and 4 volatile compounds (methyl tert-butyl ether, cis-dichlorethen, 1,4-dioxane and 1......-through reactor to simulate industrial applications. Initial experiments on the activation of oxidants with a LP lamp indicated that S2O8(2-) is photolysed about 2.3times faster than H2O2 and that the applied treatment times were not sufficient to utilize the majority of the oxidant. The effect of oxidants...

  10. A novel technique for producing antibody-coated microprobes using a thiol-terminal silane and a heterobifunctional crosslinker.

    Science.gov (United States)

    Routh, V H; Helke, C J

    1997-02-01

    Antibody-coated microprobes are used to measure neuropeptide release in the central nervous system. Although they are not quantitative, they provide the most precise spatial resolution of the location of in vivo release of any currently available method. Previous methods of coating antibody microprobes are difficult and time-consuming. Moreover, using these methods we were unable to produce evenly coated antibody microprobes. This paper describes a novel method for the production of antibody microprobes using thiol-terminal silanes and the heterobifunctional crosslinker, 4-(4-N-maleimidophenyl)butyric acid hydrazide HCl 1/2 dioxane (MPBH). Following silation, glass micropipettes are incubated with antibody to substance P (SP) that has been conjugated to MPBH. This method results in a dense, even coating of antibody without decreasing the biological activity of the antibody. Additionally, this method takes considerably less time than previously described methods without sacrificing the use of antibody microprobes as micropipettes. The sensitivity of the microprobes for SP is in the picomolar range, and there is a linear correlation between the log of SP concentration (M) and B/B0 (r2 = 0.98). The microprobes are stable for up to 3 weeks when stored in 0.1 M sodium phosphate buffer with 50 mM NaCl (pH 7.4) at 5 degrees C. Finally, insertion into the exposed spinal cord of an anesthetized rat for 15 min produces no damage to the antibody coating.

  11. Preparation and characterization of biopolymers comprising chitosan-grafted-ENR via acid-induced reaction of ENR50 with chitosan

    Directory of Open Access Journals (Sweden)

    M. R. H. Mas Haris

    2014-02-01

    Full Text Available This paper describes the first detailed tailored-approach for the preparation of biopolymers comprising chitosan (CTS grafted onto the backbone of epoxidized natural rubber (CTS-g-ENR. In a typical experiment, appropriate amount of CTS and AlCl3•6H2O was added to a specified amount of ENR50 (ENR with about 50% epoxy content dissolved in a dual-solvent consisting of 1,4-dioxane and water (97.5:2.5% v/v and the resulting mixture refluxed with continuous stirring for 6 hours. Nuclear magnetic resonance (NMR spectral analysis of a biocomposite, CTS-g-ENR-P1, revealed that its epoxy content is 22.36% which is considerably lower than 44.93% as determined for ENR50-control (ENR50 derivative obtained under similar experimental condition but in the absence of CTS. This means that the grafting of CTS onto the backbone of ENR had occurred. The revelation is affirmed by the presence of the characteristic absorption bands of CTS and ENR, and the appearance of new bands at 1219, 902 and 733 cm–1 in the Fourier transform infrared (FTIR spectrum of CTS-g-ENR-P1. Further evidence that CTS had been successfully grafted onto the backbone of ENR can be deduced and described in this paper from the data obtained by means of Differential Scanning Calorimetric analysis, Thermogravimetric analysis and Variable Pressure Scanning Electron Microscopy.

  12. Protective effect of black seed oil of nigella sativa in rats during tumour induction and radiotherapy

    International Nuclear Information System (INIS)

    Hussein, H.I.M.

    2007-01-01

    the present study was conducted to evaluate the potency of nigella sativa freshly crushed seeds (0.42 g/kg body weight) or oil ( 2.5 ml/kg body weight) for preventing tumor induction through exposure of rats to a common pollutant (1,4- dioxane) as a promoter under condition of the presence of an initiator ( N-nitrosodiethylamine). the antitumor effect was evaluated alone or in combination with low doses of γ-irradiation as a route of cancer treatment. female swiss albino rats were administered orally twice weekly with nigella sativa before and during exposure of rats to the carcinogenic compounds. animals were exposed to 3 doses of radiation (3 Gy/dose) day after day 2 weeks before the end of the experiment . the animals were sacrificed after one week of radiation, homocysteine, glutathione, lipid peroxide, GGT activity, nitric oxide, total protein, albumin and bilirubin levels were estimated in blood after 7 and 12 months from the start of the experiment .this work also includes histopathological study.rats injected with the carcinogenic compounds showed marked elevation in homocysteine, GGT activity, nitric oxide, bilirubin and lipid peroxide levels accompanied by a significant decrease in glutathione, total proteins and albumin levels

  13. Charge ordered insulating phases of DODHT salts with octahedral anions and a new radical salt, β''-(DODHT)2TaF6

    Science.gov (United States)

    Nishikawa, H.; Oshio, H.; Higa, M.; Kondo, R.; Kagoshima, S.; Nakao, A.; Sawa, H.; Yasuzuka, S.; Murata, K.

    2008-10-01

    Physical properties of isostructural β''-(DODHT)2X [DODHT = (l,4-dioxane-2,3-diyldithio)dihydrotetrathiafulvalene; X = PF6, AsF6, and SbF6] at ambient pressure have been compared. The insulating phase of β''-(DODHT)2PF6 salt has already been revealed to be a charge ordering (CO) state by X-ray diffraction study and magnetic behavior. CO in this salt was also confirmed by the observation of satellite reflections in oscillation photograph using synchrotron radiation. Transport property of β''-(DODHT)2SbF6 salt was reinvestigated up to the pressure of 3.7 GPa applied by a cubic anvil apparatus. Although the SbF6 salt turned to be metallic above 2.0 GPa, no superconductivity was observed. In order to examine the anion size dependence of DODHT salts with octahedral anions, we prepared a new DODHT salt, β''-(DODHT)2TaF6, which has the larger counter anion compared with the previous salts. Crystal structure of this salt was isostructural to the other DODHT salts. The electrical and magnetic properties of this salt were similar to those of β''-(DODHT)2SbF6 salt.

  14. Charge ordered insulating phases of DODHT salts with octahedral anions and a new radical salt, {beta}''-(DODHT){sub 2}TaF{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, H; Oshio, H; Yasuzuka, S [Graduate School of Pure and Applied Sciences, University of Tsukuba, Tsukuba, Ibaraki 305-8571 (Japan); Higa, M; Kondo, R; Kagoshima, S [Department of Basic Science, University of Tokyo, Tokyo 153-8902 (Japan); Nakao, A; Sawa, H [Photon Factory, Institute of Material Structure Science, High Energy Accelerator Research Organization, Tsukuba, Ibaraki 305-0801 (Japan); Murata, K [Graduate School of Science, Osaka City University, Osaka 558-8585 (Japan)], E-mail: nishikaw@chem.tsukuba.ac.jp

    2008-10-15

    Physical properties of isostructural {beta}''-(DODHT){sub 2}X [DODHT = (l,4-dioxane-2,3-diyldithio)dihydrotetrathiafulvalene; X = PF{sub 6}, AsF{sub 6}, and SbF{sub 6}] at ambient pressure have been compared. The insulating phase of {beta}''-(DODHT){sub 2}PF{sub 6} salt has already been revealed to be a charge ordering (CO) state by X-ray diffraction study and magnetic behavior. CO in this salt was also confirmed by the observation of satellite reflections in oscillation photograph using synchrotron radiation. Transport property of {beta}''-(DODHT){sub 2}SbF{sub 6} salt was reinvestigated up to the pressure of 3.7 GPa applied by a cubic anvil apparatus. Although the SbF{sub 6} salt turned to be metallic above 2.0 GPa, no superconductivity was observed. In order to examine the anion size dependence of DODHT salts with octahedral anions, we prepared a new DODHT salt, {beta}''-(DODHT){sub 2}TaF{sub 6}, which has the larger counter anion compared with the previous salts. Crystal structure of this salt was isostructural to the other DODHT salts. The electrical and magnetic properties of this salt were similar to those of {beta}''-(DODHT){sub 2}SbF{sub 6} salt.

  15. Low Operational Stability of Enzymes in Dry Organic Solvents: Changes in the Active Site Might Affect Catalysis

    Directory of Open Access Journals (Sweden)

    Gabriel Barletta

    2012-02-01

    Full Text Available The potential of enzyme catalysis in organic solvents for synthetic applications has been overshadowed by the fact that their catalytic properties are affected by organic solvents. In addition, it has recently been shown that an enzyme’s initial activity diminishes considerably after prolonged exposure to organic media. Studies geared towards understanding this last drawback have yielded unclear results. In the present work we decided to use electron paramagnetic resonance spectroscopy (EPR to study the motion of an active site spin label (a nitroxide free radical during 96 h of exposure of the serine protease subtilisin Carlsberg to four different organic solvents. Our EPR data shows a typical two component spectra that was quantified by the ratio of the anisotropic and isotropic signals. The isotropic component, associated with a mobile nitroxide free radical, increases during prolonged exposure to all solvents used in the study. The maximum increase (of 43% was observed in 1,4-dioxane. Based on these and previous studies we suggest that prolonged exposure of the enzyme to these solvents provokes a cascade of events that could induce substrates to adopt different binding conformations. This is the first EPR study of the motion of an active-site spin label during prolonged exposure of an enzyme to organic solvents ever reported.

  16. Kinetics of hydrogen isotope exchange reactions

    International Nuclear Information System (INIS)

    Gold, V.; McAdam, M.E.

    1975-01-01

    Under the influence of tritium β-radiation, 1,4-dioxan undergoes hydrogen exchange with the solvent water. The inhibition of the reaction by known electron scavengers (Ag + , Cu 2+ , Ni 2+ , Co 2+ , Zn 2+ , H 3 + O) and also by species with high reactivity towards hydroxyl radicals but negligible reactivity towards solvated electrons (N 3 - , Br - , SCN - ) has been examined in detail. γ-irradiation similarly induces hydrogen exchange. The action of scavengers is interpreted as requiring the involvement of two separately scavengeable primary radiolysis products in the sequence of reactions leading to exchange. The presence of electron scavengers, even at high concentration, does not totally inhibit the exchange, and a secondary exchange route, involving a low vacancy state of inhibitor cations, is considered responsible for the 'unscavengeable' portion of the reaction, by providing an alternative exchange route. Analogies are drawn between the exchange reaction and other radiation-induced reactions that are thought to involve spur processes. Some implication of radiation-chemical studies in water-alcohol mixtures are indicated. (author)

  17. Evaluation of mechanical and morphologic features of PLLA membranes as supports for perfusion cells culture systems

    Energy Technology Data Exchange (ETDEWEB)

    Montesanto, S., E-mail: salvatore.montesanto1985@gmail.com [Department of Civil, Environmental, Aerospace, Materials Engineering (DICAM), University of Palermo, Viale delle Scienze Ed. 8, 90128 Palermo (Italy); Brucato, V. [Department of Civil, Environmental, Aerospace, Materials Engineering (DICAM), University of Palermo, Viale delle Scienze Ed. 8, 90128 Palermo (Italy); La Carrubba, V. [Department of Civil, Environmental, Aerospace, Materials Engineering (DICAM), University of Palermo, Viale delle Scienze Ed. 8, 90128 Palermo (Italy); Euro-Mediterranean Institute of Science and Technology (IEMEST), Via Michele Miraglia, 20, 90128 Palermo (Italy)

    2016-12-01

    Porous biodegradable PLLA membranes, which can be used as supports for perfusion cell culture systems were designed, developed and characterized. PLLA membranes were prepared via diffusion induced phase separation (DIPS). A glass slab was coated with a binary PLLA–dioxane solution (8 wt.% PLLA) via dip coating, then pool immersed in two subsequent coagulation baths, and finally dried in a humidity-controlled environment. Surface and mechanical properties were evaluated by measuring pore size, porosity via scanning electron microscopy, storage modulus, loss modulus and loss angle by using a dynamic mechanical analysis (DMA). Cell adhesion assays on different membrane surfaces were also performed by using a standard count method. Results provide new insights into the foaming methods for producing polymeric membranes and supply indications on how to optimise the fabrication parameters to design membranes for tissue cultures and regeneration. - Highlights: • Design, development and characterization of porous biodegradable PLLA membranes via DIPS technology. • Easy-to-tune processing parameters in terms of surface and volumetric properties and cell adhesion. • Evaluation of the impact of the interconnection degree on membrane's mechanical properties. • Evaluation of cell adhesion on different membrane surface textures.

  18. Acoustic wave propagation in fluids with coupled chemical reactions

    International Nuclear Information System (INIS)

    Margulies, T.S.; Schwarz, W.H.

    1984-08-01

    This investigation presents a hydroacoustic theory which accounts for sound absorption and dispersion in a multicomponent mixture of reacting fluids (assuming a set of first-order acoustic equations without diffusion) such that several coupled reactions can occur simultaneously. General results are obtained in the form of a biquadratic characteristic equation (called the Kirchhoff-Langevin equation) for the complex propagation variable chi = - (α + iω/c) in which α is the attenuation coefficient, c is the phase speed of the progressive wave and ω is the angular frequency. Computer simulations of sound absorption spectra have been made for three different chemical systems, each comprised of two-step chemical reactions using physico-chemical data available in the literature. The chemical systems studied include: (1) water-dioxane, (2) aqueous solutions of glycine and (3) cobalt polyphosphate mixtures. Explicit comparisons are made between the exact biquadratic characteristic solution and the approximate equation (sometimes referred to as a Debye equation) previously applied to interpret the experimental data for the chemical reaction contribution to the absorption versus frequency. The relative chemical reaction and classical viscothermal contributions to the sound absorption are also presented. Several discrepancies that can arise when estimating thermodynamic data (chemical reaction heats or volume changes) for multistep chemical reaction systems when making dilute solution or constant density assumptions are discussed

  19. TEMPO addition into pre-irradiated fluoropolymers and living-radical graft polymerization of styrene for preparation of polymer electrolyte membranes

    Energy Technology Data Exchange (ETDEWEB)

    Sawada, Shin-ichi, E-mail: sawada.shinnichi@jaea.go.j [Conducting Polymer Materials Research Group, Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Department of Nuclear Engineering and Management, Graduate School of Engineering, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Suzuki, Akihiro; Terai, Takayuki [Department of Nuclear Engineering and Management, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Maekawa, Yasunari, E-mail: maekawa.yasunari@jaea.go.j [Conducting Polymer Materials Research Group, Quantum Beam Science Directorate, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan)

    2010-04-15

    We prepared proton exchange membranes (PEMs) by 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO)-mediated living-radical graft polymerization (LRGP) of styrene into fluoropolymer films and subsequent sulfonation. Poly(vinylidene fluoride) (PVDF) and poly(ethylene-co-tetrafluoroethylene) (ETFE) films were first irradiated and then treated with TEMPO solutions in various solvents. TEMPO addition was confirmed by the test of styrene grafting into TEMPO-treated films at 60 deg. C, at which the LRGP never proceeds. This test enabled us to differentiate the LRGP from the conventional graft polymerization. In order to gain a deep insight about TEMPO-addition reaction, the TEMPO-penetration behavior into the base polymer films was examined by a permeation experiment and computer simulation. Xylene and dioxane were appropriate solvents for the complete introduction of TEMPO into PVDF and ETFE films, respectively. Then, the LRGP of styrene was performed based on the fully TEMPO-capped films at 125 deg. C with various solvents. By using an alcoholic solvent, the degree of grafting was enhanced and it reached a maximum of 38%. This grafted film was sulfonated to prepare a PEM showing an ion exchange capacity of 2.2 meq/g and proton conductivity of 1.6x10{sup -1} S/cm.

  20. A facile degradable linkage for timed drug delivery

    International Nuclear Information System (INIS)

    Kenawy, E.; Abdel-Hay, F.I.; El-Newehy, M.H.; Ottenbrite, R.M.

    2005-01-01

    New drug delivery systems based on hydroxamic acid polymers were evaluated. The system support was the poly acryloyl chloride which was synthesized via free radical polymerization of acryloyl chloride in 1,4-dioxane, initiated with 2,2-azobisisobutyronitrile. Poly(N-alkyl substituted acrylamide) were synthesized in Poly(acryloyl chloride) was modified in two steps, the first is with N-hydroxysuccinimide to give the imide ester of poly(acryloyl). In the second step, the imide ester of poly(acryloyl) was reacted either with hydroxylamine or with (N-methyl hydroxylamine), respectively. The hydroxamic polymers were reacted with, the model drug, ketoprofen, in the presence of dicyclohexylcarbodiimide at -5 degree C. All products were characterized by elemental analysis, FTIR and 1 HNMR spectra. In vitro drug release study was performed at various ph and temperature to elucidate the influence of temperature and ph on the hydrolysis rate of the amido-ester bond that links the drug to the macromolecule. The amount of drug released from N-methyl hydroxamic acid polymers was higher than from hydroxamic acid polymers. All polymers showed higher drug release at 37 degree C than at room temperature (25 degree C) and at higher ph

  1. Ion exchange studies with ferrocyanide molybdate and zirconium phosphate in mixed solvent media. Part 1: Synthesis of the exchangers

    International Nuclear Information System (INIS)

    Ramaswamy, M.; Sunder Rajan, N.S.

    1979-01-01

    The present research forms the first part of the series on the investigation of the ion exchange behaviour of ferrocyanide molybdate(FeMo) and zirconium phosphate(ZrP) in water-alcohol and water-dioxane media. Since the above exchangers are not available indigenously, they were synthesized following published methods. That the reported methods of synthesis yield products with reproducible characteristics, were checked. pH titration of these two preparations in aqueous media showed that FeMo is a stronger acid than ZrP, the former, moreover, in its Cs + and Na + forms commence dissolving at pH values close to 5 and 2 respectively, and are completely dissolved at pH values 7.5 and 2.85 respectively. Titration curves with ZrP further indicated that as the pH increases, there occurs a reversal in the order of arrangement of Na + and Cs + curves, which reversal is attributed to a corresponding reversal of selectivity. Finally, both the chemical analysis and pH titration of FeMo confirm the existence of 4 replaceable H + ions corresponding to H 4 Fe(CN) 6 , a constituent of ferrocyanide molybdate, while those of ZrP are consistent with the empirical formula Zr(HPO 4 ) 2 .4.5 H 2 O, having two replaceable H + ions. (auth.)

  2. Cyanoketene and Iminopropadienones.

    Science.gov (United States)

    Moloney, Daniel W. J.; Wong, Ming Wah; Flammang, Robert; Wentrup, Curt

    1997-06-27

    Cyanoketene (8) is generated in high yields on flash vacuum thermolysis (FVT) of suitably substituted Meldrum's acid derivatives (5-[(alkylamino)(methylthio or alkylamino)methylene]-2,2-dimethyl-1,3-dioxane-4,6-diones) (3e-j), and also on FVT of cyanoacetic acid derivatives 9e,f,g,j,k,m. The major reaction pathway from 3 proceeds via ketenimines 6 and (alkylimino)propadienones 7, the latter undergoing a retro-ene reaction to 8. A minor pathway is via imidoylketenes 4e,h and oxoketenimines 5e,h, which undergo retro-ene reactions to 9. All intermediates were characterized by Ar matrix FTIR and tandem mass spectrometry (collisional activation MS). Trapping of 4, 5, and 8 with nucleophiles is also reported. The preference of 1,3-X shifts over 1,5-H shifts in imidoylketenes 12 (X = SMe or NMe(2)) is corroborated by the calculated activation barriers. Neat cyanoketene is highly reactive, reacting at or below 80 K, and this is attributed to the availability of a low-lying ketene LUMO. The IR spectrum of cyanoketene (Ar, 14 K) is dominated by two absorptions at 2163 (s; C=C=O) and 2239 (w; CN) cm(-)(1) in excellent agreement with density functional (B3-LYP/6-31G) and ab initio (QCISD/6-31G) calculations.

  3. Investigation of Different Colloidal Porous Silicon Solutions and Their Composite Solid Matrix Rods by Optical Techniques

    Science.gov (United States)

    Khan, M. Naziruddin; Aldalbahi, Ali; Almohammedi, Abdullah

    2018-03-01

    Colloidal porous silicon (PSi) in different solvents was synthesized by simple chemical etching. Colloidal solutions were then prepared using different quantities of silicon wafer pieces (Pcs) and chloroplatinic (Pt) acid in catalyst solution. The effect on the properties of the colloidal solutions and composite rods were investigated using various optical characterization techniques. Absorption and photoluminescence (PL) intensity of the colloidal PSi solutions are observed to depend on the quantity of wafer Pcs, the Pt-solution, and the porosity formation on the wafer surface. The morphological structure of the PSi in a solvent and the solid-rod environments were studied using field-emission scanning electron microscopy (FE-SEM) and were observed to have different structures. A mono-oriented structure of PSi exists in tetrahydrofuran, which has stereo orientation in dioxane and dimethylsulfoxide (approximately 5-8 nm as confirmed using high resolution transmission electron microscopy). Subsequently, some colloidal PSi solutions were directly embedded in three types of sol-gel-based matrices, silica, ormosils (or organically modified silica) and polymer, which easily generated solid rods. Spontaneous emission (SE) of the PSi solutions and their composite rods were examined using a high power picosecond 355 nm laser source. The emitted PL and SE signals of the colloidal PSi solutions were dependent on the Pt volume, nature of the solvent, quantity of Si wafer piece, and pumping energy. The response of SE signals from the PSi composites rods is an interesting phenomenon, and such nanocomposites may be used for future research on light amplification.

  4. Porous asymmetric SiO2-g-PMMA nanoparticles produced by phase inversion

    KAUST Repository

    Munirasu, Selvaraj

    2014-07-22

    A new kind of asymmetric organic-inorganic porous structure has been proposed. Asymmetric lattices of polymer grafted silica nanoparticles were manufactured by casting and phase inversion in water. Silica nanoparticles were first functionalized with 3-(dimethylethoxysilyl)propyl-2-bromoisobutyrate, followed by grafting of poly(methylmethacrylate) (PMMA) segments, performed by atom-transfer radical polymerization. Mechanically stable self-standing films were prepared by casting a dispersion of functionalized nanoparticles in different solvents and immersion in water. The resulting asymmetrically porous morphology and nanoparticle assembly was characterized by scanning electron and atomic force microscopy. The PMMA functionalized SiO2 hybrid material in acetone or acetone/dioxane led to the best-assembled structures. Porous asymmetric membranes were prepared by adding free PMMA and PMMA terminated with hydrophilic hydroxyl group. Nitrogen flow of 2800 L m-2 h -1 was measured at 1.3 bar demonstrating the porosity and potential application for membrane technology. © 2014 Springer Science+Business Media New York.

  5. Eco-friendly Synthesis of Organics and Nanomaterials ...

    Science.gov (United States)

    The presentation summarizes our recent activity in chemical synthesis involving benign alternatives, such as the use of supported reagents, and greener reaction medium in aqueous or solvent-free conditions.1 The synthesis of heterocyclic compounds, coupling reactions, and a variety of name reactions2 are the primary beneficiaries as exemplified by the synthesis of N-aryl azacycloalkanes, isoindoles, and dihydropyrazoles, 1,3,4-oxadiazoles, 1,3,4-thiadiazoles, 1,3-dioxanes, pyrazoles, catalyzed by basic water or polystyrene sulfonic acid (PSSA) in conjunction with microwave (MW) irradiation.2 Vitamins B1, B2, C, and tea and wine polyphenols which function both as reducing and capping agents, provide extremely simple, one-pot, green synthetic methods to bulk quantities of nanomaterials in water.3a Shape-controlled synthesis of noble nanostructures via MW-assisted spontaneous reduction of noble metal salts using sugars will be presented.3b A general method has been developed for the cross-linking reaction of poly (vinyl alcohol) (PVA) with metallic systems; bimetallic systems,3c and SWNT, MWNT, and C-60.3d The strategy is extended to the formation of biodegradable carboxymethylcellulose (CMC) composite films with noble nanometals;3e such metal decoration and alignment of carbon nanotubes in CMC is possible using MW approach3f which also enables the shape-controlled bulk synthesis of Ag and Fe nanorods in poly (ethylene glycol).3g MW hydrothermal process delivers m

  6. Synthesis, characterization and physiological activity of some novel isoxazoles.

    Directory of Open Access Journals (Sweden)

    NITIN G. GHODILE

    2012-07-01

    Full Text Available Hushare VJ, Rajput PR, Malpani MO, Ghodile NG. 2012. Synthesis, characterization and physiological activity of some novel isoxazoles. Nusantara Bioscience 4: 81-85. A series of chlorosubstituted 4-aroylisoxazoles have been synthesized by refluxing chlorosubstituted-3-aroylflavones and 3-alkoylchromone with hydroxylamine hydrochloride in dioxane medium containing 0.5 mL piperidine. Chlorosubstituted-3-aroylflavones and chlorosubstituted-3-alkoylchromone were prepared by refluxing them separately with iodine crystal in ethanol. Initially chlorosubstituted-3-aroylflavanones and 3-alkoylchromanone were prepared by the interaction of different aromatic and aliphatic aldehydes with 1-(2’-hydroxy-3’,5’-dichlorophenyl-3-phenyl-1,3-propanedione. Constitutions of synthesized compounds were confirmed on the basis of elemental analysis, molecular weight determination, UV-Visible, I.R. and 1H-NMR spectral data. The titled compounds were evaluated for their growth promoting activity on some flowering plants viz. Papaver rhoeas, Calendula officinalise, Gladiola tristis, Gaillardia aristata, Dianthus chinensis, and Iberis sp. (candytuft. The results indicate that applicated plants had higher shoots and more number of leaves.

  7. Changes in the classification of carcinogenic chemicals in the work area. (Section III of the German List of MAK and BAT values).

    Science.gov (United States)

    Neumann, H G; Thielmann, H W; Filser, J G; Gelbke, H P; Greim, H; Kappus, H; Norpoth, K H; Reuter, U; Vamvakas, S; Wardenbach, P; Wichmann, H E

    1998-01-01

    Carcinogenic chemicals in the work area were previously classified into three categories in section III of the German List of MAK and BAT values (the list of values on maximum workplace concentrations and biological tolerance for occupational exposures). This classification was based on qualitative criteria and reflected essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. In the new classification scheme the former sections IIIA1, IIIA2, and IIIB are retained as categories 1, 2, and 3, to correspond with European Union regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, these three categories are supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not contribute significantly to the risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. Chemicals known to act typically by non-genotoxic mechanisms, and for which information is available that allows evaluation of the effects of low-dose exposures, are classified in category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose/response relationships and toxicokinetics and for which risk at low doses can be assessed are classified in category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for category 4 (1,4-dioxane) and category 5 (styrene) are presented.

  8. Changes in the classification of carcinogenic chemicals in the work area. Section III of the German List of MAK and BAT Values.

    Science.gov (United States)

    Neumann, H G; Vamvakas, S; Thielmann, H W; Gelbke, H P; Filser, J G; Reuter, U; Greim, H; Kappus, H; Norpoth, K H; Wardenbach, P; Wichmann, H E

    1998-11-01

    Carcinogenic chemicals in the work area are currently classified into three categories in section III of the German List of MAK and BAT Values (list of values on maximum workplace concentrations and biological tolerance for occupational exposures). This classification is based on qualitative criteria and reflects essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. It is proposed that these categories - IIIA1, IIIA2, IIIB - be retained as Categories 1, 2, and 3, to correspond with European Union regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, these three categories are supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not contribute significantly to risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. Chemicals known to act typically by nongenotoxic mechanisms and for which information is available that allows evaluation of the effects of low-dose exposures, are classified in Category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose-response relationships and toxicokinetics, and for which risk at low doses can be assessed are classified in Category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for Category 4 (1,4-dioxane) and Category 5 (styrene) are presented.

  9. A new luminescent terbium 4-methylsalicylate complex as a novel sensor for detecting the purity of methanol.

    Science.gov (United States)

    Zeng, Cheng-Hui; Yang, Yang-Yi; Zhu, Yi-Min; Wang, Hong-Ming; Chu, Tian-Shu; Ng, Seik Weng

    2012-01-01

    A new dinuclear terbium complex [Tb(2)(4-msal)(6)(H(2)O)(4)]·6H(2)O (1) (4-msal = 4-methylsalcylate) was synthesized. Its structure was determined by single crystal X-ray diffraction, and the complex was characterized by PXRD, FT-IR, fluorescence, TGA and DTA. Complex 1 exists as discrete molecules that are linked by extensive O-H … O hydrogen bonds into a 3D network. The luminescence lifetimes of 3 μM methanol solution and solid sample of 1 are 1.321 and 1.009 ms, respectively. The quantum yield of solid sample is 6.0%. The luminescence quenched more than 50% when 3% (vol/vol) different impurities (acetone, acetonitrile, chloroform, dichloromethane, dioxane, DMF, DMSO, ethanol, ether, ethyl acetate, glycol, H(2)O, hexane, TEA, THF and toluene or their mixture) were added. The inverse linear relationship between the Lg value of fluorescence intensity and the volume ratio of the minor component (to a maximum of 20%) is interpreted in terms of LgI = a-bX (I: luminescence intensity; X: volume ratio of impurities in methanol; a, b are constants). So 1 is a potential luminescent sensor for analyzing the purity of methanol. © 2012 Wiley Periodicals, Inc. Photochemistry and Photobiology © 2012 The American Society of Photobiology.

  10. Crystallization and preliminary X-ray characterization of two thermostable DNA nucleases

    International Nuclear Information System (INIS)

    Kuettner, E. Bartholomeus; Pfeifer, Sven; Keim, Antje; Greiner-Stöffele, Thomas; Sträter, Norbert

    2006-01-01

    Two thermostable DNA nucleases from archaea were crystallized in different space groups; the crystals were suitable for X-ray analysis. Temperature-tolerant organisms are an important source to enhance the stability of enzymes used in biotechnological processes. The DNA-cleaving enzyme exonuclease III from Escherichia coli is used in several applications in gene technology. A thermostable variant could expand the applicability of the enzyme in these methods. Two homologous nucleases from Archaeoglobus fulgidus (ExoAf) and Methanothermobacter thermoautrophicus (ExoMt) were studied for this purpose. Both enzymes were crystallized in different space groups using (poly)ethylene glycols, 2,4-methyl pentandiol, dioxane, ethanol or 2-propanol as precipitants. The addition of a 10-mer DNA oligonucleotide was important to obtain monoclinic crystals of ExoAf and ExoMt that diffracted to resolutions better than 2 Å using synchrotron radiation. The crystal structures of the homologous proteins can serve as templates for genetic engineering of the E. coli exonuclease III and will aid in understanding the different catalytic properties of the enzymes

  11. Problems associated with scintillation counting of NaH14CO3 and gel suspension counting of Ba14CO3

    International Nuclear Information System (INIS)

    MacRae, J.C.; Wilson, S.

    1978-01-01

    Liquid NaH 14 CO 3 was assayed in emulsion-type (NE260 and Unisolve) and dioxan-based (NE250) scintillation cocktails contained in glass or polyethylene vials kept at 2 0 or 24-30 0 C. Different particle size ranges of standard Ba 14 CO 3 were assayed by gel suspension counting in Cabosil scintillation cocktail and in NE260 following solubilisation in EDTA-tetrasodium salt. Initial detectable activities of NaH 14 CO 3 in glass and polyethylene vials in NE250, NE260 and Unisolve were 97 and 96, 68 and 83, 71 and 89% of the true value respectively. Subsequent losses of activity over 7 days with the emulsion-type scintillators was greater from the polyethylene vials. Addition of phenylethylamine to the NE260 and Unisolve cocktails gave the true activity levels for all vials with no loss of activity over 6 days. When different particle size ranges of Standard Ba 14 CO 3 were suspended in Cabosil scintillation cocktail there was considerable variation in counting efficiency (77-88%) with little relationship between particle size and counting efficiency. The relationship between counting efficiency and channels ratio was not sufficiently precise for predictive purposes. Solubilisation of Ba 14 CO 3 in EDTA-tetrasodium salt gave similar counting efficiency and channels ratio values for all samples. (U.K.)

  12. Rutin from Ruta graveolens L

    Directory of Open Access Journals (Sweden)

    Dj. Afshar

    1994-08-01

    Full Text Available Quantitative determination of rutin in Ruta Graveolens, L. which is easily cultivated in Iran, is necessary for its economic importance, diversity of specialities and their pharmacological activity in blood vessels disorders. For this purpose, the plant was cultivated in botanical garden of Tabriz University of Medical Sciences and rutin was determinated at different stages of plant growth. The extraction was done from the crude plants by ethanol, boiling water and hydroalcoholic solvents. Rutin was subsequently purified by crystalization."nStructure elucidation was confirmed by the U.V spectrum in the presence of shift-producing reagents, and TLC by using different systems, HPLC and HPTLC in the presence of standard."nSugars and their sequence of bonding to genine were known by acidic hydrolysis, sequential hydrolysis and TLC in the presence of standards. For quantitative determinations of rutin two methods were selected i.e. HPLC and colorimetery. In the colorimetrey method, cyanidin reaction was used for color producing and the absorbances of other compounds of extract were eliminated in coincidence with rutin absorption.. In the HPLC method, separation was done on CN- column with mobile phase including dioxan/phosphate bnffer (pH=2.6; 2:8. In the end the results of two methods were compared.

  13. Deuterium isotope fractionation between ortho-alkyl substituted phenols and t-butylthiol in oxygen bases

    International Nuclear Information System (INIS)

    Wawer, A.; Jelenska-Kazimierczuk, M.; Szydlowski, J.

    1998-01-01

    Equilibrium isotope effect in the exchange reaction of deuterium between phenol(P), 2-isopropyl phenol (IPP), 2,6-diisopropyl phenol (DIPP), 2,6-diterbutyl phenol (DTBP) and tertbutylthiol (TBT) has been studied in 296 K. The fractionation factors (α) have been measured in cyclohexane and carbon tetrachloride solutions and in a few oxygen bases: acetone, 1,4-dioxane, ethyl formate, ethyl ether, tetrahydrofurane, N,N-dimethylformamide, dimethylsulfoxide and hexamethylphosphoramide. Using chemical shifts of phenol OH protons, the thermodynamic parameters of complex formation with the oxygen bases have been determined. The experimental data show that lnα correlates with the formation enthalpy of the phenol-oxygen base complex in DIPP-TBT-base system but there is no simple correlation in IPP-TBT-base system. Furthermore, it was found that in DTBT-TBT-base system lnα depends linearly on the basicity of the solvent (DN parameters). On the other hand, lnα correlates with acidic parameters of the solvents (AN) in IPP-TBT-base and P-TBT-base systems. All above correlations are explained by taking into account two competition processes: self association of phenol molecules and their solvation by oxygen bases. (author)

  14. Fabricating a pearl/PLGA composite scaffold by the low-temperature deposition manufacturing technique for bone tissue engineering

    International Nuclear Information System (INIS)

    Xu Mingen; Li Yanlei; Suo Hairui; Wang Qiujun; Ge Yakun; Xu Ying; Yan Yongnian; Liu Li

    2010-01-01

    Here we developed a composite scaffold of pearl/poly(lactic-co-glycolic acid) (pearl/PLGA) utilizing the low-temperature deposition manufacturing (LDM). LDM makes it possible to fabricate scaffolds with designed microstructure and macrostructure, while keeping the bioactivity of biomaterials by working at a low temperature. Process optimization was carried out to fabricate a mixture of pearl powder, PLGA and 1,4-dioxane with the designed hierarchical structures, and freeze-dried at a temperature of -40 deg. C. Scaffolds with square and designated bone shape were fabricated by following the 3D model. Marrow stem cells (MSCs) were seeded on the pearl/PLGA scaffold and then cultured in a rotating cell culture system. The adhesion, proliferation and differentiation of MSCs into osteoblasts were determined using scanning electronic microscopy, WST-1 assay, alkaline phosphatase activity assay, immunofluorescence staining and real-time reverse transcription polymerase chain reaction. The results showed that the composite scaffold had high porosity (81.98 ± 3.75%), proper pore size (micropores: <10 μm; macropore: 495 ± 54 μm) and mechanical property (compressive strength: 0.81 ± 0.04 MPa; elastic modulus: 23.14 ± 0.75 MPa). The pearl/PLGA scaffolds exhibited better biocompatibility and osteoconductivity compared with the tricalcium phosphate/PLGA scaffold. All these results indicate that the pearl/PLGA scaffolds fulfill the basic requirements of bone tissue engineering scaffold.

  15. Rh(I)-Catalyzed Arylation of Heterocycles via C-H Bond Activation: Expanded Scope Through Mechanistic Insight

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, Jared; Berman, Ashley; Bergman, Robert; Ellman, Jonathan

    2007-07-18

    A practical, functional group tolerant method for the Rh-catalyzed direct arylation of a variety of pharmaceutically important azoles with aryl bromides is described. Many of the successful azole and aryl bromide coupling partners are not compatible with methods for the direct arylation of heterocycles using Pd(0) or Cu(I) catalysts. The readily prepared, low molecular weight ligand, Z-1-tert-butyl-2,3,6,7-tetrahydrophosphepine, which coordinates to Rh in a bidentate P-olefin fashion to provide a highly active yet thermally stable arylation catalyst, is essential to the success of this method. By using the tetrafluoroborate salt of the corresponding phosphonium, the reactions can be assembled outside of a glove box without purification of reagents or solvent. The reactions are also conducted in THF or dioxane, which greatly simplifies product isolation relative to most other methods for direct arylation of azoles employing high-boiling amide solvents. The reactions are performed with heating in a microwave reactor to obtain excellent product yields in two hours.

  16. Synthesis and in Vitro Antifungal Activity against Botrytis cinerea of Geranylated Phenols and Their Phenyl Acetate Derivatives

    Directory of Open Access Journals (Sweden)

    María I. Chávez

    2015-08-01

    Full Text Available The inhibitory effects on the mycelial growth of plant pathogen Botritys cinerea have been evaluated for a series of geranylphenols substituted with one, two and three methoxy groups in the aromatic ring. The results show that the antifungal activity depends on the structure of the geranylphenols, increasing from 40% to 90% by increasing the number of methoxy groups. On the other hand, the acetylation of the –OH group induces a change of activity that depends on the number of methoxy groups. The biological activity of digeranyl derivatives is lower than that exhibited by the respective monogeranyl compound. All tested geranylphenols have been synthesized by direct coupling of geraniol and the respective phenol. The effect of solvent on yields and product distribution is discussed. For monomethoxyphenols the reaction gives better yields when acetonitrile is used as a solvent and AgNO3 is used as a secondary catalyst. However, for di- and trimethoxyphenols the reaction proceeds only in dioxane.

  17. Tautomerism of 4-hydrazinoquinazolines: vibrational spectra and computational study

    Directory of Open Access Journals (Sweden)

    Tetiana Yu. Sergeieva

    2014-03-01

    Full Text Available The tautomerism of 4-hydrazinoquinazoline and its derivatives was investigated. Geometry and thermodynamic parameters were computed theoretically using Gaussian 03 software. All calculations were performed at the MP2 level of theory using the standard 6-31G(d basis. Energetics and relative stabilities of tautomers were compared and analyzed in a gas phase. The effect of solvents (1,4-dioxane, acetic acid, ethanol and water on the tautomeric equlibria was evaluated using PCM. It was determined that solvents induced slight changes in the relative stability. In all cases 4-hydrazinoquinazoline exists predominantly as the amino form. The variation of dipole moments was studied. The anharmonic vibrational wavenumbers for unsubstituted 4-hydrazinoquinazoline were calculated at MP2/6-31G(d level and compared with experimental data. The modes of IR spectra were assigned. The calculated herein wavenumbers and intensities of amino form are in good agreement with those observed experimentally.      

  18. The synthesis of taurine-conjugated bile acids and bile acid sulfates labeled with {sup 14}C or {sup 3}H in the taurine moiety

    Energy Technology Data Exchange (ETDEWEB)

    Jie Zhang; Griffiths, W.J.; Sjoevall, Jan [Karolinska Inst., Medical Biochemistry and Biophysics Dept., Stockholm (Sweden)

    1997-02-01

    Studies of bile acid transport systems require radio-labeled taurine-conjugated bile acids with high specific activity. An established procedure was optimized to provide mild, fast, and effective conjugation of radio-labeled taurine with different types of bile acids, including those with labile 7{alpha}-hydroxy-3-oxo-{Delta}{sup 4} or 3{beta}, 7{alpha}-dihydroxy-{Delta}{sup 5} structures. Taurine labeled with {sup 14}C or {sup 3}H was reacted with excess bile acid anhydride formed from the tributylamine salt and ethylchloroformate (2/1 M/M) in aqueous dioxane for 15 min at room temperature. The yields were higher than 95% and less than 2% side products were formed. Bile acid sulfates were conjugated with {sup 14}C- or {sup 3}H-labeled taurine by using N-ethoxycarbonyl-2-ethoxy-1,2-dihydroquinoline as the coupling reagent. The products were effectively purified by chromatography of the sodium salts on Sephadex LH-20. The yields of taurine-conjugated bile acid sulfates were 65-70%. (author).

  19. Desalination by electrodialysis with the ion-exchange membrane prepared by radiation-induced graft polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Seong-Ho; Han Jeong, Young; Jeong Ryoo, Jae; Lee, Kwang-Pill E-mail: kplee@kyungpook.ac.kr

    2001-07-01

    Ion-exchange membranes modified with the triethylamine [-N(CH{sub 2}CH{sub 3}){sub 3}] and phosphoric acid (-PO{sub 3} H) groups were prepared by radiation-induced grafting of glycidyl methacrylate (GMA) onto the polyolefin nonwavon fabric (PNF) and subsequent chemical modification of poly(GMA) graft chains. The physical and chemical properties of the GMA-grafted PNF and the PNF modified with ion-exchange groups were investigated by SEM, XPS, TGA, and DSC. Furthermore, electrochemical properties such as specific electric resistance, transport number of K{sup +}, and desalination were examined. The grafting yield increased with increasing reaction time and reaction temperature. The maximum grafting yield was obtained with 40% (vol.%) monomer concentration in dioxane at 60 deg. C. The content of the cation- and anion-exchange group increased with increasing grafting yield. Electrical resistance of the PNF modified with TEA and -PO{sub 3} H group decreased, while the water uptake (%) increased with increasing ion-exchange group capacities. Transport number of the PNF modified with ion-exchange group were the range of ca. 0.82-0.92. The graft-type ion-exchange membranes prepared by radiation-induced graft copolymerization were successfully applied as separators for electrodialysis. (author)

  20. Antagonism of acetylcholine by adrenaline antagonists

    Science.gov (United States)

    Benfey, B. G.; Grillo, S. A.

    1963-01-01

    Phenoxybenzamine antagonized the inhibitory action of acetylcholine on the guinea-pig isolated atrium. The antagonism was slow in onset, very slowly reversible, and could be overcome by increased concentrations of acetylcholine. In contrast, atropine inhibited the action of acetylcholine quickly, and the effect disappeared soon after withdrawal. The pA10 of phenoxybenzamine (2 hr of contact) was 6.8, and that of atropine (30 min of contact) was 8.4. In the presence of atropine phenoxybenzamine did not exert a slowly reversible antagonism, and the dose-ratio of acetylcholine returned to normal soon after withdrawal of both drugs. Phenoxybenzamine also antagonized acetylcholine in the guinea-pig isolated ileum, but with higher concentrations acetylcholine did not overcome the antagonism. The pA10 (60 min of contact) was 6.6. The pA10 of chlorpromazine in the atrium (2 hr of contact) and ileum (60 min of contact) was 5.9. Phentolamine, 2-diethylaminomethylbenzo-1,4-dioxan hydrochloride (883 F), and yohimbine antagonized acetylcholine in the atrium and ileum but required higher concentrations than chlorpromazine. PMID:13967429

  1. METHODS ELABORATION ON DETECTION OF SOME ATYPICAL NEUROLYTIC AGENTS FOR CHEMICAL AND TOXICOLOGICAL ANALYSIS

    Directory of Open Access Journals (Sweden)

    I. P. Remezova

    2014-01-01

    Full Text Available It is necessary to elaborate methods of atypical neuroleptic agents detection as individual substances and in different combinations as well for diagnosis of poisoning by some of them: clozapine, risperidone, sertindole, olanzapine, aripiprazole. The purpose of this work is methods elaboration of detection of clozapine, risperidone, sertindole, olanzapine, aripiprazole, haloperidol, oxazepam, carbamazapine using TLC, HPLC and UV spectrophotometry methods. During this work we used tablet forms of clozapine, risperidone, sertindole, olanzapine, aripiprazole. It is possible to use solution systems like ethanol-water-25% ammonia solution (8:1:1, toluolacetone-ethanol-25% ammonia solution (45:45:7.5:2.5, dioxan-chloroform-acetone-25% ammonia solution (47.5:45:5:2.5 for preliminary examination of atypical neuroleptic agents under study in combination with typical neuroleptics and tranquilizers with undirected analysis (general screening. System of solvents ethyl-acetate-chloroform-25% ammonia solution (85:10:5 is recommended to use for individual screening of risperidone, sertindole, olanzapine, haloperidol, benzol-ethanol-25% ammonia solution (50:10:0.5 system to use for clozapine, sertindole, olanzapine. Ethanol-25% ammonia solution (100:1.5 system is reasonable to use for chromatographic clearance of extracts from biological substances under study. We recommend using HPLC method and UV spectrophotometry for carrying out of a principal examination of clozapine, risperidone, sertindole, olanzapine and aripiprazole in case one of the substances under study is determined in the object.

  2. Simultaneous spectrophotometric determination of trimethoprim and sulphamethoxazole following charge-transfer complexation with chloranilic acid

    Directory of Open Access Journals (Sweden)

    Olajire A. Adegoke

    2017-05-01

    Full Text Available A simple, accurate and precise simultaneous spectrophotometric method has been developed for the analysis of trimethoprim–sulphamethoxazole combination in pure and tablet dosage forms. The method involves direct charge transfer complexation of trimethoprim (TMP with chloranilic acid (CAA in acetonitrile–dioxane solvent mixture and complexation of sulphamethoxazole (SMZ after its hydrolysis in dilute H2SO4. Optimization of temperature and time revealed the superiority of room temperature and 20 and 30 min respectively for TMP and SMZ. Optimal detector responses were obtained at 520 and 440 nm and were therefore selected as working wavelength maxima for SMZ and TMP respectively. TMP and hydrolysed SMZ were combined with CAA at mole ratios of 1:1 and 1:3 respectively. Accuracies were generally less than 4% (estimated as degree of inaccuracy or error with a precision of the order of less than 2% on a three-day assessment. Physicochemical factors responsible for complex stability were estimated and related to the observed data. The method was successfully applied to the determination of TMP and SMZ in tablet dosage forms with accuracies comparable to the official BP method. There were no interferences from common tablet excipients and TMP complex did not interfere with the assay of SMZ. The developed method could find application in routine quality control of TMP–SMZ combination. It is the first reported full simultaneous colorimetric assay of TMP and SMZ using the same analytical reagent.

  3. The synthesis of [U-14C phenyl] LS 840606, an agricultural fungicide

    International Nuclear Information System (INIS)

    Madegard, G.; Mestre, P.; Raimond, P.; Noel, J.-P.

    1995-01-01

    2,2',4'-Trichloro-[ring U- 14 C]acetophenone was the key intermediate of this synthesis patterned after the industrial route. An unexpected poor yield was observed during the preparation by the Friedel-Crafts reaction of chloroacetyl chloride with 1,3-dichloro-[U- 14 C]benzene, possibly the result of an isotope effect although this poor yield might be explained by other factors. Two routes were checked for the preparation of 1,3-dichloro-[U- 14 C]benzene. The action of CCl 4 with 1,3-dinitro-[U- 14 C]benzene at 280 o C was entailed with explosions. A safer route started from [U- 14 C]aniline via 2,4-dichloro-[ring U- 14 C]acetanilide. Friedel-Crafts reaction with acetyl chloride gave rise in 52% yield to 2',4'-dichloro-[ring U- 14 C]acetophenone which was brominated to 2-bromo-2',4'-dichloro-[ring U- 14 C]acetophenone; was condensed with 2,2-ethylenedioxy)etylmagnesium bromide to compound, was condensed with 1,2,4-triazole then successively treated with HCl:water:dioxane and 2,2,2-trifluoroethanol/HCl. Separation of the two diastereomers by medium pressure liquid chromatography. 7% overall radioactivity yield from [U- 14 C]aniline. Radiochemical purity 99%. (author)

  4. Behavior of soluble and immobilized acid phosphatase in hydro-organic media.

    Science.gov (United States)

    Wan, H; Horvath, C

    1975-11-20

    The hydrolysis of p-nitrophenyl phosphate by wheat germ acid phosphatase (orthophosphoric monoester phosphohydrolase, EC 3.1.3.2) has been investigated in mixtures of aqueous buffers with acetone, dioxane and acetonitrile. The enzyme was either in free solution or immobilized on a pellicular support which consisted of a porous carbonaceous layer on solid glass beads. The highest enzyme activity was obtained in acetone and acetonitrile mixed with citrate buffer over a wide range of organic solvent concentration. In 50% (v/v) acetone both V and Km of the immobilized enzyme were about half of the values in the neat aqueous buffer, but the Ki for inorganic phosphate was unchanged. In 50% (v/v) mixtures of various solvents and citrate buffers of different pH, the enzymic activity was found to depend on the pH of the aqueous buffer component rather than the pH of the hydro-organic mixture as measured with the glass-calomel electrode. The relatively high rates of p-nitrophenol liberation in the presence of glucose even at high organic solvent concentrations suggest that transphosphorylation is facilitated at low water activity.

  5. In Situ GISAXS Study on Solvent Vapour Induced Orientation Switching in PS-b-P4VP Block Copolymer Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Gowd, E Bhoje; Boehme, Marcus; Stamm, Manfred, E-mail: gowd@ipfdd.de, E-mail: bhojegowd@yahoo.com [Department of Nanostructured Materials Leibniz Institute of Polymer Research Dresden Hohe Strasse 6, 01069, Dresden (Germany)

    2010-11-15

    We investigated the orientation changes of cylindrical P4VP microdomains in PS-b-P4VP thin films upon annealing in different solvent vapours using the time-resolved in situ grazing-incidence small-angle X-ray scattering (GISAXS) for the first time. Swelling of perpendicular cylinders (C perpendicular) in a non-selective solvent vapours (chloroform) leads to the orientation change to in-plane cylinders (C//) and it occurs through a disordered state. On the other hand, swelling of perpendicular cylinders (C perpendicular) in a selective solvent vapours (1,4-dioxane) leads the morphological change from cylindrical to BCC spherical morphology. Solvent evaporation results in shrinkage of the matrix in the vertical direction and subsequently merges the spheres into the perpendicularly aligned cylinders. The selectivity of the solvent to constituting blocks and the solvent evaporation rate may be mainly responsible for such orientation change of cylindrical P4VP microdomains in PS-b-P4VP thin films.

  6. Further characterization of 4-bromomisonidazole as a potential detector of hypoxic cells

    International Nuclear Information System (INIS)

    Rasey, J.S.; Krohn, K.A.; Grunbaum, Z.; Conroy, P.J.; Bauer, K.; Sutherland, R.M.

    1985-01-01

    [ 14 C]Bromomisonidazole was prepared by direct bromination of [ring-2] [ 14 C]misonidazole in dioxane. The uptake and binding of the two labeled sensitizers were compared in vitro in 1-mm EMT-6 spheroids which contain a necrotic core. Using liquid scintillation counting it was shown that spheroids incubated with 50 μM [ 14 C]bromomisonidazole concentrated drug above levels in the medium by 1 1/2 hr and achieved maximum concentration by 10 hr with no further increase at 23 hr. Spheroids incubated with 50 μM[ 14 C]misonidazole may concentrate the sensitizer more slowly but ultimately reached the same fivefold increase over levels in the medium by 23 hr as was observed for bromomisonidazole. Autoradiographs prepared from spheroids after incubation with [ 14 C]misonidazole or [ 14 C]bromomisonidazole showed silver grains preferentially located over viable hypoxic cells in the inner half of the spheroid rim adjacent to the necrotic center, with lower grain density over nonviable necrotic areas and many fewer grains over oxic cells at the periphery of the spheroid. The data support the potential of radiolabled bromomisonidazole for in vivo imaging pending additional studies of the metabolism of this agent

  7. Amorphous Solid Dispersion of Epigallocatechin Gallate for Enhanced Physical Stability and Controlled Release.

    Science.gov (United States)

    Cao, Yizheng; Teng, Jing; Selbo, Jon

    2017-11-09

    Epigallocatechin gallate (EGCG) has been recognized as the most prominent green tea extract due to its healthy influences. The high instability and low bioavailability, however, strongly limit its utilization in food and drug industries. This work, for the first time, develops amorphous solid dispersion of EGCG to enhance its bioavailability and physical stability. Four commonly used polymeric excipients are found to be compatible with EGCG in water-dioxane mixtures via a stepwise mixing method aided by vigorous mechanical interference. The dispersions are successfully generated by lyophilization. The physical stability of the dispersions is significantly improved compared to pure amorphous EGCG in stress condition (elevated temperature and relative humidity) and simulated gastrointestinal tract environment. From the drug release tests, one of the dispersions, EGCG-Soluplus ® 50:50 ( w / w ) shows a dissolution profile that only 50% EGCG is released in the first 20 min, and the remains are slowly released in 24 h. This sustained release profile may open up new possibilities to increase EGCG bioavailability via extending its elimination time in plasma.

  8. Attachment chemistry of aromatic compounds on a Silicon(100) surface

    Science.gov (United States)

    Henriksson, Anders; Nishiori, Daiki; Maeda, Hiroaki; Miyachi, Mariko; Yamanoi, Yoshinori; Nishihara, Hiroshi

    2018-03-01

    A mild method was developed for the chemical attachment of aromatic compounds directly onto a hydrogen-terminated Si(100) (H-Si(100)) surface. In the presence of palladium catalyst and base, 4-iodophenylferrocene and a π-conjugated iron complex were attached to H-Si(100) electrodes and hydrogen-terminated silicon nanowires (H-SiNWs), both of which have predominant dihydride species on their surfaces. The reactions were conducted in 1,4-dioxane at 100 °C and the immobilization of both 4-ferrocenylphenyl group and π-conjugated molecular wires were confirmed and quantified by XPS and electrochemical measurements. We reported densely packed monolayer whose surface coverage (Γ), estimated from the electrochemical measurements are in analogue to similar monolayers prepared via thermal or light induced hydrosilylation reactions with alkenes or alkynes. The increase in electrochemical response observed on nanostructured silicon surfaces corresponds well to the increase in surface area, those strongly indicating that this method may be applied for the functionalization of electrodes with a variety of surface topographies.

  9. Structural characterization of lignin from grape stalks (Vitis vinifera L.).

    Science.gov (United States)

    Prozil, Sónia O; Evtuguin, Dmitry V; Silva, Artur M S; Lopes, Luísa P C

    2014-06-18

    The chemical structure of lignin from grape stalks, an abundant waste of winemaking, has been studied. The dioxane lignin was isolated from extractive- and protein-free grape stalks (Vitis vinifera L.) by modified acidolytic procedure and submitted to a structural analysis by wet chemistry (nitrobenzene and permanganate oxidation (PO)) and spectroscopic techniques. The results obtained suggest that grape stalk lignin is an HGS type with molar proportions of p-hydroxyphenyl (H), guaiacyl (G) and syringyl (S) units of 3:71:26. Structural analysis by (1)H and (13)C NMR spectroscopy and PO indicates the predominance of β-O-4' structures (39% mol) in grape stalk lignin together with moderate amounts of β-5', β-β, β-1', 5-5', and 4-O-5' structures. NMR studies also revealed that grape lignin should be structurally associated with tannins. The condensation degree of grape stalks lignin is higher than that of conventional wood lignins and lignins from other agricultural residues.

  10. Preparation and characterization of standardized pomegranate extract-phospholipid complex as an effective drug delivery tool

    Directory of Open Access Journals (Sweden)

    Amisha Kamlesh Vora

    2015-01-01

    Full Text Available Punicalagins, a pair of anomeric ellagitannins, present in Punica granatum (Pomegranates are known to possess excellent antioxidant activity in vitro, but poor oral bioavailability. The reasons cited for poor bioavailability are their large molecular size, poor lipophilicity, and degradation by colonic microflora into less active metabolites. The objective of the present research work was to complex the standardized pomegranate extract (SPE with phospholipid to formulate standardized pomegranate extract-phospholipid complex (SPEPC, characterize it and check its permeability through an ex vivo everted gut sac experiment. SPEPC was prepared by mixing SPE (30% punicalagins and soya phosphatidylcholine (PC in 1:1 v/v mixture of methanol and dioxane and spray-drying the mixture. The complex was characterized by infrared spectroscopy, differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy. It was evaluated for its octanol solubility, dissolution, and permeability by everted the gut sac technique. The characterization methods confirmed the formation of complex. Increased n-octanol solubility of the complex proved its increased lipophilicity. Dissolution studies revealed that the phospholipid covering may prevent the punicalagins to be released in gastro-intestinal tract, thus preventing their colonic microbial degradation. SPEPC showed better apparent permeability than SPE in an everted gut sac technique. Hence, it could be concluded that phospholipid complex of SPE may be of potential use in increasing the permeability and hence the bioavailability of punicalagins.

  11. A new process for fabricating nanodot arrays on selective regions with diblock copolymer thin film

    Energy Technology Data Exchange (ETDEWEB)

    Park, Dae-Ho [Department of Materials Science and Engineering, Polymer Research Institute, Pohang University of Science and Technology, San 31, Hyoja-Dong, Nam-Gu, Pohang 790-784 (Korea, Republic of)

    2007-09-12

    A procedure for micropatterning a single layer of nanodot arrays in selective regions is demonstrated by using thin films of polystyrene-b-poly(t-butyl acrylate) (PS-b-PtBA) diblock copolymer. The thin-film self-assembled into hexagonally arranged PtBA nanodomains in a PS matrix on a substrate by solvent annealing with 1,4-dioxane. The PtBA nanodomains were converted into poly(acrylic acid) (PAA) having carboxylic-acid-functionalized nanodomains by exposure to hydrochloric acid vapor, or were removed by ultraviolet (UV) irradiation to generate vacant sites without any functional groups due to the elimination of PtBA domains. By sequential treatment with aqueous sodium bicarbonate and aqueous zinc acetate solution, zinc cations were selectively loaded only on the carboxylic-acid-functionalized nanodomains prepared via hydrolysis. Macroscopic patterning through a photomask via UV irradiation, hydrolysis, sequential zinc cation loading and calcination left a nanodot array of zinc oxide on a selectively UV-shaded region.

  12. Real-time mass spectroscopy analysis of Li-ion battery electrolyte degradation under abusive thermal conditions

    Science.gov (United States)

    Gaulupeau, B.; Delobel, B.; Cahen, S.; Fontana, S.; Hérold, C.

    2017-02-01

    The lithium-ion batteries are widely used in rechargeable electronic devices. The current challenges are to improve the capacity and safety of these systems in view of their development to a larger scale, such as for their application in electric and hybrid vehicles. Lithium-ion batteries use organic solvents because of the wide operating voltage. The corresponding electrolytes are usually based on combinations of linear, cyclic alkyl carbonates and a lithium salt such as LiPF6. It has been reported that in abusive thermal conditions, a catalytic effect of the cathode materials lead to the formation fluoro-organics compounds. In order to understand the degradation phenomenon, the study at 240 °C of the interaction between positive electrode materials (LiCoO2, LiNi1/3Mn1/3Co1/3O2, LiMn2O4 and LiFePO4) and electrolyte in dry and wet conditions has been realized by an original method which consists in analyzing by mass spectrometry in real time the volatile molecules produced. The evolution of specific gases channels coupled to the NMR reveal the formation of rarely discussed species such as 2-fluoroethanol and 1,4-dioxane. Furthermore, it appears that the presence of water or other protic impurities greatly influence their formation.

  13. Evaluation of mechanical and morphologic features of PLLA membranes as supports for perfusion cells culture systems

    International Nuclear Information System (INIS)

    Montesanto, S.; Brucato, V.; La Carrubba, V.

    2016-01-01

    Porous biodegradable PLLA membranes, which can be used as supports for perfusion cell culture systems were designed, developed and characterized. PLLA membranes were prepared via diffusion induced phase separation (DIPS). A glass slab was coated with a binary PLLA–dioxane solution (8 wt.% PLLA) via dip coating, then pool immersed in two subsequent coagulation baths, and finally dried in a humidity-controlled environment. Surface and mechanical properties were evaluated by measuring pore size, porosity via scanning electron microscopy, storage modulus, loss modulus and loss angle by using a dynamic mechanical analysis (DMA). Cell adhesion assays on different membrane surfaces were also performed by using a standard count method. Results provide new insights into the foaming methods for producing polymeric membranes and supply indications on how to optimise the fabrication parameters to design membranes for tissue cultures and regeneration. - Highlights: • Design, development and characterization of porous biodegradable PLLA membranes via DIPS technology. • Easy-to-tune processing parameters in terms of surface and volumetric properties and cell adhesion. • Evaluation of the impact of the interconnection degree on membrane's mechanical properties. • Evaluation of cell adhesion on different membrane surface textures.

  14. The synthesis of taurine-conjugated bile acids and bile acid sulfates labeled with 14C or 3H in the taurine moiety

    International Nuclear Information System (INIS)

    Jie Zhang; Griffiths, W.J.; Sjoevall, Jan

    1997-01-01

    Studies of bile acid transport systems require radio-labeled taurine-conjugated bile acids with high specific activity. An established procedure was optimized to provide mild, fast, and effective conjugation of radio-labeled taurine with different types of bile acids, including those with labile 7α-hydroxy-3-oxo-Δ 4 or 3β, 7α-dihydroxy-Δ 5 structures. Taurine labeled with 14 C or 3 H was reacted with excess bile acid anhydride formed from the tributylamine salt and ethylchloroformate (2/1 M/M) in aqueous dioxane for 15 min at room temperature. The yields were higher than 95% and less than 2% side products were formed. Bile acid sulfates were conjugated with 14 C- or 3 H-labeled taurine by using N-ethoxycarbonyl-2-ethoxy-1,2-dihydroquinoline as the coupling reagent. The products were effectively purified by chromatography of the sodium salts on Sephadex LH-20. The yields of taurine-conjugated bile acid sulfates were 65-70%. (author)

  15. Coumarin- and Carboxyl-Functionalized Supramolecular Polybenzoxazines Form Miscible Blends with Polyvinylpyrrolidone

    Directory of Open Access Journals (Sweden)

    Ruey-Chorng Lin

    2017-04-01

    Full Text Available In this study, we synthesized a novel multifunctional benzoxazine monomer (Coumarin-COOH BZ, possessing both coumarin and COOH groups, through the reaction of 4-methyl-7-hydroxycoumarin, 4-aminobenzoic acid, and paraformaldehyde in 1,4-dioxane, with the structure confirmed using 1H and 13C nuclear magnetic resonance and Fourier transform infrared (FTIR spectroscopy. Differential scanning calorimetry (DSC, FTIR spectroscopy, and thermogravimetric analysis were then employed to monitor the thermal curing behavior of Coumarin-COOH BZ and its blends with poly(N-vinyl-2-pyrrolidone (PVP, both before and after photodimerization of the coumarin moieties. DSC revealed a single glass transition temperature for each Coumarin-COOH BZ/PVP blend composition; a large positive deviation based on the Kwei equation suggested that strong hydrogen bonding existed between the Coumarin-COOH BZ and PVP segments, confirmed through FTIR spectroscopic analyses. The thermal properties improved (i.e., increased glass transition and thermal degradation temperatures as a result of the increased crosslinking density after photodimerization under UV exposure.

  16. Synthesis of Functional Polyester Based on Polylactic Acid and Its Effect on PC12 Cells after Coupling with Small Peptides

    Directory of Open Access Journals (Sweden)

    Na Qiang

    2016-01-01

    Full Text Available Polyesters containing functional groups are a suitable candidate matrix for cell culture in tissue engineering. Three types of semicrystalline copolymer poly(L-lactide-co-β-malic acid [P(LA-co-BMD] with pendent carboxyl groups were synthesized in this study. The functional monomer 3(S-[(benzyloxycarbonylmethyl]-1,4-dioxane-2,5-dione (BMD was synthesized using L-aspartic acid. The copolymer P(LA-co-BMD was then synthesized through ring-opening copolymerization of L-LA and BMD, with dodecanol as initiator and stannous octoate as catalyst. Copolymer structure was characterized by 1H nuclear magnetic resonance (1H NMR, gel permeation chromatography (GPC, and differential scanning calorimetry (DSC analyses. Results of 1H NMR and GPC analyses showed that the copolymers were synthesized successfully. DSC curves showed that the crystal melting peak and enthalpy decreased with increased BMD. The crystallinity of the copolymer was destroyed by the presence of the functional monomer. After deprotection, carboxyl groups were coupled with the isoleucine-lysine-valine-alanine-valine peptide through N-hydroxysuccinimide/dicyclohexylcarbodiimide method. The small peptide was beneficial to the axon growth of PC12 cells.

  17. Anti-L. donovani activity in macrophage/amastigote model of palmarumycin CP18 and its large scale production.

    Science.gov (United States)

    Ortega, Humberto E; Teixeira, Eliane de Morais; Rabello, Ana; Higginbotham, Sarah; Cubilla-Ríos, Luis

    2014-01-01

    Palmarumycin CP18, isolated from an extract of the fermentation broth and mycelium of the Panamanian endophytic fungus Edenia sp., was previously reported with strong and specific activity against Leishmania donovani. Here we report that when the same strain was cultured on different solid media--Harrold Agar, Leonian Agar, Potato dextrose Agar (PDA), Corn Meal Agar, Honey Peptone Agar, and eight vegetables (V8) Agar--in order to determine the optimal conditions for isolation of palmarumycin CP18, no signal for this compound was observed in any of the 1H NMR spectra of fractions obtained from these extracts. However, one extract, prepared from the fungal culture in PDA contained significant amounts of CJ-12,372, a possible biosynthetic precursor of palmarumycin CP18. Edenia sp. was cultivated on a large scale on PDA and CJ-12,372 was converted to palmarumycin CP18 by oxidation of its p-hydroquinone moiety with DDQ in dioxane. Palmarumycin CP18 showed anti-leishmanial activity against L. donovani in a macrophage/amastigote model, with IC50 values of 23.5 microM.

  18. Influence of different environments on the excited-state proton transfer and dual fluorescence of fisetin

    Science.gov (United States)

    Guharay, Jayanti; Dennison, S. Moses; Sengupta, Pradeep K.

    1999-05-01

    The influence of different protic and aprotic solvent environments on the excited-state intramolecular proton transfer (ESIPT) leading to a dual fluorescence behaviour of a biologically important, naturally occurring, polyhydroxyflavone, fisetin (3,3',4',7-tetrahydroxyflavone), has been investigated. The normal fluorescence band, in particular, is extremely sensitive to solvent polarity with νmax shifting from 24 510 cm -1 in dioxane ( ET(30)=36.0) to 20 790 cm -1 in methanol ( ET(30)=55.5). This is rationalized in terms of solvent dipolar relaxation process, which also accounts for the red edge excitation shifts (REES) observed in viscous environments such as glycerol at low temperatures. Significant solvent dependence of the tautomer fluorescence properties ( νmax, yield and decay kinetics) reveals the influence of external hydrogen bonding perturbation on the internal hydrogen bond of the molecule. These excited-state relaxation phenomena and their relevant parameters have been used to probe the microenvironment of fisetin in a membrane mimetic system, namely AOT reverse micelles in n-heptane at different water/surfactant molar ratio ( w0).

  19. Molecular imprinting of enzymes with water-insoluble ligands for nonaqueous biocatalysis.

    Science.gov (United States)

    Rich, Joseph O; Mozhaev, Vadim V; Dordick, Jonathan S; Clark, Douglas S; Khmelnitsky, Yuri L

    2002-05-15

    Attaining higher levels of catalytic activity of enzymes in organic solvents is one of the major challenges in nonaqueous enzymology. One of the most successful strategies for enhancing enzyme activity in organic solvents involves tuning the enzyme active site by molecular imprinting with substrates or their analogues. Unfortunately, numerous imprinters of potential importance are poorly soluble in water, which significantly limits the utility of this method. In the present study, we have developed strategies that overcome this limitation of the molecular-imprinting technique and that thus expand its applicability beyond water-soluble ligands. The solubility problem can be addressed either by converting the ligands into a water-soluble form or by adding relatively high concentrations of organic cosolvents, such as tert-butyl alcohol and 1,4-dioxane, to increase their solubility in the lyophilization medium. We have succeeded in applying both of these strategies to produce imprinted thermolysin, subtilisin, and lipase TL possessing up to 26-fold higher catalytic activity in the acylation of paclitaxel and 17beta-estradiol compared to nonimprinted enzymes. Furthermore, we have demonstrated for the first time that molecular imprinting and salt activation, applied in combination, produce a strong additive activation effect (up to 110-fold), suggesting different mechanisms of action involved in these enzyme activation techniques.

  20. Extractive process for preparing high purity magnesium chloride hexahydrate

    Directory of Open Access Journals (Sweden)

    Fezei Radouanne

    2012-01-01

    Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

  1. Hydroperoxide Traces in Common Cyclic Ethers as Initiators for Controlled RAFT Polymerizations.

    Science.gov (United States)

    Eggers, Steffen; Abetz, Volker

    2018-04-01

    Herein, a reversible addition-fragmentation chain transfer (RAFT) polymerization is introduced for reactive monomers like N-acryloylpyrrolidine or N,N-dimethylacrylamide working without a conventional radical initiator. As a very straightforward proof of principle, the method takes advantage of the usually inconvenient radical-generating hydroperoxide contaminations in cyclic ethers like tetrahydrofuran or 1,4-dioxane, which are very common solvents in polymer sciences. The polymerizations are surprisingly well controlled and the polymers can be extended with a second block, indicating their high livingness. "Solvent-initiated" RAFT polymerizations hence prove to be a feasible access to tailored materials with minimal experimental effort and standard laboratory equipment, only requiring the following ingredients: hydroperoxide-contaminated solvent, monomer, and RAFT agent. In other respects, however, the potential coinitiating ability of the used solvent is to be considered when investigating the kinetics of RAFT polymerizations or aiming for the synthesis of high-livingness polymers, e.g., multiblock copolymers. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. 4f-4f absorption spectral analysis of complexation of Pr(IlI) and Nd(IlI) with fumaric acid and maleic acid in different solvents

    International Nuclear Information System (INIS)

    Singh, Th. David; Taru Taru, T.; Nimita, L.; Singh, N. Rajmuhon

    2008-01-01

    Full text: Dimensions to lanthanide co-ordination chemistry in solution become a new age with the increase use of lanthanides as PROBES in the exploration of the structural function of biomolecular reactions. Absorption difference and comparative absorption spectrophotometric studies involving 4f-4f transitions for the complexation of Pr(III)/Nd(lIl) with fumaric acid and maleic acid have been carried out in CH 3 OH,CH 3 CN, dioxane and DMF. The small chemical and structural differences due to the ligands and solvents are shown to produce significant red shift and variation in the intensities of observed 4f-4f absorption bands. The variation in the spectral energy parameters - Slater Condon (F K ), Lande spin orbit coupling constant (ζ 4f ), nephelauxetic ratio (β), bonding parameter (b 1/2 ) and percent covalency (δ) are calculated and correlated with binding of the ligands with Pr(III)/Nd(III). In addition to this experimentally calculated oscillator strengths (P) and calculated values of Judd-Ofelt electric dipole intensity parameters, T λ (λ=2,4,6) are discussed for different 4f-4f transitions in different experimental conditions to discuss the nature of bonding between Ln(lIl) and ligands. The participation of π-electron density of ligands with complexation is also discussed

  3. Synthesis and characterization of polyphosphazene electrolytes including cyclic ether side groups

    Science.gov (United States)

    Fiedler, Carsten; Luerssen, Bjoern; Lucht, Brett; Janek, Juergen

    2018-04-01

    This paper presents the synthesis and detailed characterization of two polyphosphazene based polymers, including different cyclic ether side groups. The final polymers were obtained by a well-known method employing a living cationic polymerization and subsequent nucleophilic substitution. The synthesized polymers Poly [(1,3-dioxane-5-oxy) (1,3-dioxolane-4-methoxy)phosphazene] (DOPP) and Poly[bis(2-Tetrahydro-3-furanoxy)phosphazene] (THFPP) were mixed with varied amounts of lithium bis(trifluoromethane)sulfonamide (LiTFSI) and the interactions between the salt and the polymer chains were studied by Fourier transform infrared (FT-IR) and differential scanning calorimetry (DSC) measurements. Electrochemical characterization was performed by electrochemical impedance spectroscopy (EIS) and direct current polarization in the temperature range of 20-60 °C. These measurements were utilized to calculate the lithium transference number (t+), the lithium conductivity (σ) and its activation energy in order to elucidate the lithium transport behavior. Relatively high lithium transference numbers of 0.6 (DOPP) and 0.7 (THFPP) at 60 °C are found and reveal maximum lithium conductivities of 2.8·10-6 Sṡcm-1 and 9.0·10-7 Sṡcm-1 for DOPP and THFPP at 60 °C, respectively.

  4. Cometabolic bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Hazen, Terry C.

    2009-02-15

    Cometabolic bioremediation is probably the most under appreciated bioremediation strategy currently available. Cometabolism strategies stimulate only indigenous microbes with the ability to degrade the contaminant and cosubstrate e.g. methane, propane, toluene and others. This highly targeted stimulation insures that only those microbes that can degrade the contaminant are targeted, thus reducing amendment costs, well and formation plugging, etc. Cometabolic bioremediation has been used on some of the most recalcitrant contaminants, e.g. PCE, TCE, MTBE, TNT, dioxane, atrazine, etc. Methanotrophs have been demonstrated to produce methane monooxygense, an oxidase that can degrade over 300 compounds. Cometabolic bioremediation also has the advantage of being able to degrade contaminants to trace concentrations, since the biodegrader is not dependent on the contaminant for carbon or energy. Increasingly we are finding that in order to protect human health and the environment that we must remediate to lower and lower concentrations, especially for compounds like endocrine disrupters, thus cometabolism may be the best and maybe the only possibility that we have to bioremediate some contaminants.

  5. Differential measurement of low level HTO and HT leak rates

    International Nuclear Information System (INIS)

    Sheehan, W.E.; Muldoon, K.M.

    1976-08-01

    Leak rates of 5 x 10 -17 cm 3 /sec and greater can be measured by a very simple technique that will also differentiate tritium oxide (HTO) from tritium gas (HT). Because of the much greater health hazard of tritium oxide (200 to 1), the determination of chemical form is significant. The method involves flushing a gas collection chamber, containing the item being measured, with dry air. The flushed air is passed through an ethylene glycol bubbler which removes only the HTO. The outlet of the ethylene glycol bubbler is connected to a heated (400 0 C) palladium sponge catalyst which converts the HT to HTO and then to a second ethylene glycol bubbler for collection of the oxidized tritium gas. Liquid scintillation (p-dioxane base) counting solution is added directly to the bubblers and counted for tritium in a Liquid Scintillation Spectrometer. Advantages, method validation, operational experience, and data obtained by this technique are discussed. The sensitivity of the method is dependent on the time allowed between bubbler changes, the liquid scintillation spectrometer counting efficiency, background, and counting times employed

  6. Ethylene/ethane permeation, diffusion and gas sorption properties of carbon molecular sieve membranes derived from the prototype ladder polymer of intrinsic microporosity (PIM-1)

    KAUST Repository

    Salinas, Octavio

    2016-01-05

    Fine-tuning the microporosity of PIM-1 by heat treatment was applied to develop a suitable carbon molecular sieve membrane for ethylene/ethane separation. Pristine PIM-1 films were heated from 400 to 800 °C under inert N2 atmosphere (< 2 ppm O2). At 400 °C, PIM-1 self-cross-linked and developed polar carbonyl and hydroxyl groups due to partial dioxane splitting in the polymer backbone. Significant degradation occurred at 600 °C due to carbonization of PIM-1 and resulted in 30% increase in cumulative surface area compared to its cross-linked predecessor. In addition, PIM-1-based CMS developed smaller ultramicropores with increasing pyrolysis temperature, which enhanced their molecular sieving capability by restricted diffusion of ethylene and ethane through the matrix due to microstructural carbon densification. Consequently, the pure-gas ethylene permeability (measured at 35 °C and 2 bar) decreased from 1600 Barrer for the pristine PIM-1 to 1.3 Barrer for the amorphous carbon generated at 800 °C, whereas the ethylene/ethane pure-gas selectivity increased significantly from 1.8 to 13.

  7. In Situ GISAXS Study on Solvent Vapour Induced Orientation Switching in PS-b-P4VP Block Copolymer Thin Films

    International Nuclear Information System (INIS)

    Gowd, E Bhoje; Boehme, Marcus; Stamm, Manfred

    2010-01-01

    We investigated the orientation changes of cylindrical P4VP microdomains in PS-b-P4VP thin films upon annealing in different solvent vapours using the time-resolved in situ grazing-incidence small-angle X-ray scattering (GISAXS) for the first time. Swelling of perpendicular cylinders (C perpendicular) in a non-selective solvent vapours (chloroform) leads to the orientation change to in-plane cylinders (C//) and it occurs through a disordered state. On the other hand, swelling of perpendicular cylinders (C perpendicular) in a selective solvent vapours (1,4-dioxane) leads the morphological change from cylindrical to BCC spherical morphology. Solvent evaporation results in shrinkage of the matrix in the vertical direction and subsequently merges the spheres into the perpendicularly aligned cylinders. The selectivity of the solvent to constituting blocks and the solvent evaporation rate may be mainly responsible for such orientation change of cylindrical P4VP microdomains in PS-b-P4VP thin films.

  8. The synthesis of [U-{sup 14}C phenyl] LS 840606, an agricultural fungicide

    Energy Technology Data Exchange (ETDEWEB)

    Madegard, G.; Mestre, P.; Raimond, P.; Noel, J.-P. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France)

    1995-12-01

    2,2`,4`-Trichloro-[ring U-{sup 14}C]acetophenone was the key intermediate of this synthesis patterned after the industrial route. An unexpected poor yield was observed during the preparation by the Friedel-Crafts reaction of chloroacetyl chloride with 1,3-dichloro-[U-{sup 14}C]benzene, possibly the result of an isotope effect although this poor yield might be explained by other factors. Two routes were checked for the preparation of 1,3-dichloro-[U-{sup 14} C]benzene. The action of CCl{sub 4} with 1,3-dinitro-[U-{sup 14} C]benzene at 280{sup o}C was entailed with explosions. A safer route started from [U-{sup 14}C]aniline via 2,4-dichloro-[ring U-{sup 14}C]acetanilide. Friedel-Crafts reaction with acetyl chloride gave rise in 52% yield to 2`,4`-dichloro-[ring U-{sup 14}C]acetophenone which was brominated to 2-bromo-2`,4`-dichloro-[ring U-{sup 14}C]acetophenone; was condensed with 2,2-(ethylenedioxy)etylmagnesium bromide to compound, was condensed with 1,2,4-triazole then successively treated with HCl:water:dioxane and 2,2,2-trifluoroethanol/HCl. Separation of the two diastereomers by medium pressure liquid chromatography. 7% overall radioactivity yield from [U-{sup 14}C]aniline. Radiochemical purity 99%. (author).

  9. The influence of irradiation of gamma-rays on the pulping and paper making, (3)

    International Nuclear Information System (INIS)

    Mori, Kenji; Sasaki, Toru; Hasegawa, Kunihiko.

    1979-01-01

    Dissolving pulp (DP) containing no lignin and cold soda pulp containing much amount of lignin were used for the study of the influence of gamma irradiation. Experiments were made in the presence of air, water, methanol, acetic anhydride, acetic anhydride + methanol, dioxane, dimethyl sulfoxide and 1% NaOH solution. Irradiation was made for 100 hours at 20 - 21 deg. C; total irradiation dose was 1.47 x 10 7 R. (1) In case of dimethyl sulfoxide, and especially in case of 1% NaOH solution, the yield decreased by irradiation, with cold soda pulp particularly. (2) In case of the pulp immersed in water, the brightness of pulp was not improved by irradiation, but in methanol, it was remarkably improved. Since the improvement was observed in both DP and cold soda pulps, it is caused by the action of oxidizing bleach with small amount of oxygen in the air remaining in the material, instead of the change in the quality of lignin. (3) By infrared analysis, methanol did not react with the lignin in cold soda pulp even under irradiation. (4) The acetylation was accelerated by irradiation. (J.P.N.)

  10. Amorphous Solid Dispersion of Epigallocatechin Gallate for Enhanced Physical Stability and Controlled Release

    Directory of Open Access Journals (Sweden)

    Yizheng Cao

    2017-11-01

    Full Text Available Epigallocatechin gallate (EGCG has been recognized as the most prominent green tea extract due to its healthy influences. The high instability and low bioavailability, however, strongly limit its utilization in food and drug industries. This work, for the first time, develops amorphous solid dispersion of EGCG to enhance its bioavailability and physical stability. Four commonly used polymeric excipients are found to be compatible with EGCG in water-dioxane mixtures via a stepwise mixing method aided by vigorous mechanical interference. The dispersions are successfully generated by lyophilization. The physical stability of the dispersions is significantly improved compared to pure amorphous EGCG in stress condition (elevated temperature and relative humidity and simulated gastrointestinal tract environment. From the drug release tests, one of the dispersions, EGCG-Soluplus® 50:50 (w/w shows a dissolution profile that only 50% EGCG is released in the first 20 min, and the remains are slowly released in 24 h. This sustained release profile may open up new possibilities to increase EGCG bioavailability via extending its elimination time in plasma.

  11. Review of the evolution of safety, ecological and economical aspects of liquid scintillation counting materials and techniques

    International Nuclear Information System (INIS)

    Kalbhen, D.A.

    1983-01-01

    The wide applicability of liquid scintillation techniques for counting weak β-emitters and other radionuclides has led to the daily use of a large number of liquid scintillation counter instruments in research and control laboratories. Of the solvents used in liquid scintillators, xylene, toluene and trimethyl benzene are most common. To a minor extent, dioxane, methylglycol, ethanol and methanol are also used. The estimated annual total volume is around 2-3 million liters of scintillation cocktails. The present situation demonstrates a problem in laboratory safety and concomitant cost for waste treatment, usually not recognized. The use and handling of these inflammable and irritant solvents can induce certain risks to personnel and laboratory safety. A significant reduction of the ecological and health risks is important. In recent years, some progress has been made by using smaller volumes and smaller sizes of vials. The introduction of non-flammable scintillator solvents, which do not penetrate through polyethylene vials and do not escape into the laboratory atmosphere, also adds to the safety process

  12. Fragranced consumer products and undisclosed ingredients

    International Nuclear Information System (INIS)

    Steinemann, Anne C.

    2009-01-01

    Fragranced consumer products-such as air fresheners, laundry supplies, personal care products, and cleaners-are widely used in homes, businesses, institutions, and public places. While prevalent, these products can contain chemicals that are not disclosed to the public through product labels or material safety data sheets (MSDSs). What are some of these chemicals and what limits their disclosure? This article investigates these questions, and brings new pieces of evidence to the science, health, and policy puzzle. Results from a regulatory analysis, coupled with a chemical analysis of six best-selling products (three air fresheners and three laundry supplies), provide several findings. First, no law in the U.S. requires disclosure of all chemical ingredients in consumer products or in fragrances. Second, in these six products, nearly 100 volatile organic compounds (VOCs) were identified, but none of the VOCs were listed on any product label, and one was listed on one MSDS. Third, of these identified VOCs, ten are regulated as toxic or hazardous under federal laws, with three (acetaldehyde, chloromethane, and 1,4-dioxane) classified as Hazardous Air Pollutants (HAPs). Results point to a need for improved understanding of product constituents and mechanisms between exposures and effects

  13. Comparative studies of bile salts. A new type of bile salt from Arapaima gigas (Cuvier) (family Osteoglossidae).

    Science.gov (United States)

    Haslewood, G A; Tökés, L

    1972-03-01

    1. Arapaima gigas bile salts were hydrolysed by alkali or cleaved with dioxan-trichloroacetic acid to give cholic acid, arapaimic acid, arapaimol-A and arapaimol-B. 2. I.r., n.m.r. and mass spectroscopy and [alpha](D) measurements indicated that arapaimic acid and arapaimol-A and -B are respectively 2alpha,3alpha,7alpha,12alpha-tetrahydroxy-5beta,25in-cholestan-26-oic acid, 5beta,25R-cholestane-2beta,3alpha,7alpha,12alpha,26-pentol and 5beta-cholestane-2beta,3alpha,7alpha,12alpha,26,27-hexol. 3. Partial synthesis of 2beta,3alpha,7alpha,12alpha-tetrahydroxy-5alpha- and -5beta-cholan-24-oic acid and their spectral examination fully confirmed these conclusions. 4. A. gigas bile salts show primitive features in that they comprise alcohol sulphates and a C(27) acid; they are also specialized in showing 2beta-hydroxylation.

  14. NANOBIOCATALYTIC SYSTEMS BASED ON LIPASE-Fe3O4 AND CONVENTIONAL SYSTEMS FOR ISONIAZID SYNTHESIS: A COMPARATIVE STUDY

    Directory of Open Access Journals (Sweden)

    V. M. Costa

    Full Text Available Abstract Superparamagnetic nanomaterials have attracted interest in many areas due to the high saturation magnetization and surface area. For enzyme immobilization, these properties favor the enzyme-support contact during the immobilization reaction and easy separation from the reaction mixture by use of low-cost magnetic processes. Iron oxide magnetic nanoparticles (Fe3O4, MNPs, produced by the co-precipitation method, functionalized with 3-aminopropyltriethoxysilane (APTES and glutaraldehyde (GLU, were evaluated as a solid support for Candida antarctica lipase B (CALB immobilization. The nanomagnetic derivative (11nm obtained after CALB immobilization (MNPs/APTES/GLU/CALB was evaluated as biocatalyst in isoniazide (INH synthesis using ethyl isonicotinate (INE and hydrazine hydrate (HID as substrates, in 1,4-dioxane. The results showed that MNPs/APTES/CALB had a similar performance when compared to a commercial enzyme Novozym 435, showing significant advantages over other biocatalysts, such as Rhizhomucor miehei lipase (RML and CALB immobilized on non-conventional, low-cost, chitosan-based supports.

  15. Synthesis of New Hydrated Geranylphenols and in Vitro Antifungal Activity against Botrytis cinerea

    Science.gov (United States)

    Soto, Mauricio; Espinoza, Luis; Chávez, María I.; Díaz, Katy; Olea, Andrés F.; Taborga, Lautaro

    2016-01-01

    Geranylated hydroquinones and other geranylated compounds isolated from Aplydium species have shown interesting biological activities. This fact has prompted a number of studies where geranylated phenol derivatives have been synthesized in order to assay their bioactivities. In this work, we report the synthesis of a series of new hydrated geranylphenols using two different synthetic approaches and their inhibitory effects on the mycelial growth of Botrytis cinerea. Five new hydrated geranylphenols were obtained by direct coupling reaction between geraniol and phenol in dioxane/water and using BF3·Et2O as the catalyst or by the reaction of a geranylated phenol with BF3·Et2O. Two new geranylated quinones were also obtained. The synthesis and structural elucidation of all new compounds is presented. All hydrated geranylphenols efficiently inhibit the mycelial growth of B. cinerea. Their activity is higher than that observed for non-hydrated compounds. These results indicate that structural modification on the geranyl chain brings about an enhancement of the inhibition effect of geranylated phenol derivatives. PMID:27271604

  16. Influence of the solvents on the γ-ray polymerization of acrylic acid. II

    International Nuclear Information System (INIS)

    Laborie, F.

    1977-01-01

    The presence of plurimolecular H-bonded aggregates in the acrylic acid allows the polymer to involve some stereoregular sequences. This effect is made easier when some polymer is already formed in the reacting medium: the aggregates are stabilized by hydrogen bonds with the polymer which gives rise to a matrix effect. Two groups of solvents have been characterized by examination of the monomer's association forms in solution. In a first group of solvents (methanol--dioxan--water), the aggregates are maintained and reinforced; in the second one, acrylic acid exists only as cyclic dimers (hydrocarbons--chlorinated solvents). The difference between the association forms of the monomer involves some important modifications on the kinetics of polymerization and the structure of the obtained polymers. In the solvents of the first group, the obtained polymers are crystallizable and may involve syndiotactic sequences, while in the presence of the solvents of the second group no crystallization or stereoregularity of the polymer can occur. A very close correlation is thus found between the aggregated structure of the monomer, the polymerization kinetics, and the structure of the polymers

  17. Synthesis of dexamethasone-4-14C

    International Nuclear Information System (INIS)

    Rao, P.N.; Cessac, J.W.; Hill, K.A.

    1982-01-01

    The bismethylenedioxy (BMD) derivative of dexamethasone 2 was silylated with trimethylchlorosilane and imidazole in dimethylformamide to give the 11β-trimethylsilyloxy BMD derivative 3. The Δ 1 -double bond in 3 was hydrogenated over 5% palladium on carbon to give the Δ 4 -3-oxo steroid 4. Oxidation of 4 with potassium permanganate-sodium metaperiodate gave the seco-acid 5 which on subsequent treatment with acetic anhydride; sodium acetate and triethylamine gave the enol-lactone 6. The enol-lactone 6 was reacted with 14 C-methylmagnesium iodide to give an adduct 7a which on heating at reflux with lithium 2,6-di-t-butylphenoxide in dioxane gave the Δ 4 -3-oxo derivative 8. Compound 8 was heated at reflux with m-iodylbenzoic acid and diphenyl diselenide in toluene to give the Δsup(1,4)-3-oxo steroid 9. The protecting BMD and silyl groups were removed in a single step by reaction with aqueous trifluoroacetic acid containing 2N hydrochloric acid at room temperature to give dexamethasone-4- 14 C 10. (author)

  18. The introduction of tritium label into natural and modified prostaglandins

    International Nuclear Information System (INIS)

    Shevchenko, V.P.; Bezuglov, V.V.; Nagayev, I.Y.; Myasoedov, N.F.

    1989-01-01

    Studies on the role of the nature of both heterogeneous catalysts and the solvent on the reduction selectively of 5,6-double bonds showed that the largest yield could be obtained by using the Lindlar catalyst and ethyl acetate. The use of different isotopes of hydrogen in the protium-deuterium-tritium series markedly decreased the hydrogenation reaction rate, but the selectivity of the process practically remained unaltered. Homogeneous catalysts were also used in the production of natural tritium-labelled prostaglandins and of their fluorine and deoxy analogues. The label was introduced by selective hydrogenation in the presence of (Ph 3 P) 3 RhCl and dioxane as solvent. Different ways have been studied of tritium-label introduction into prostaglandins modified at the carboxyl group. The synthesis of similar preparations was performed either by selective dehalogenation in the presence of heterogeneous catalysts treated with quinoline or triethylamine, or by condensation of prostaglandins at the carboxyl group by tritium-labelled amino acid. (author). 4 refs.; 1 fig

  19. Effects of the tumor-vasculature-disrupting agent verubulin and two heteroaryl analogues on cancer cells, endothelial cells, and blood vessels.

    Science.gov (United States)

    Mahal, Katharina; Resch, Marcus; Ficner, Ralf; Schobert, Rainer; Biersack, Bernhard; Mueller, Thomas

    2014-04-01

    Two analogues of the discontinued tumor vascular-disrupting agent verubulin (Azixa®, MPC-6827, 1) featuring benzo-1,4-dioxan-6-yl (compound 5 a) and N-methylindol-5-yl (compound 10) residues instead of the para-anisyl group on the 4-(methylamino)-2-methylquinazoline pharmacophore, were prepared and found to exceed the antitumor efficacy of the lead compound. They were antiproliferative with single-digit nanomolar IC50 values against a panel of nine tumor cell lines, while not affecting nonmalignant fibroblasts. Indole 10 surpassed verubulin in seven tumor cell lines including colon, breast, ovarian, and germ cell cancer cell lines. In line with docking studies indicating that compound 10 may bind the colchicine binding site of tubulin more tightly (Ebind =-9.8 kcal mol(-1) ) than verubulin (Ebind =-8.3 kcal mol(-1) ), 10 suppressed the formation of vessel-like tubes in endothelial cells and destroyed the blood vessels in the chorioallantoic membrane of fertilized chicken eggs at nanomolar concentrations. When applied to nude mice bearing a highly vascularized 1411HP germ cell xenograft tumor, compound 10 displayed pronounced vascular-disrupting effects that led to hemorrhages and extensive central necrosis in the tumor. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Biodegradation of softwood lignin and guaiacylglycerol-beta-guiacyl ether by extracellular enzyme in shiitake Lentinus edodes (Berk) Sing

    Energy Technology Data Exchange (ETDEWEB)

    Oki, T.; Senba, Y.; Ishikawa, H.

    1982-01-01

    In order to explain the biodegradation of softwood lignin by shiitake (Lentinus edodes Berk. Sing.), akamatsu (Pinus densiflora Sekb. and Zucc.) dioxane lignin (NDL) and guaicylglycerol-beta-guaiacyl ether (I) were degraded by extracellular enzyme from the NDL-contained potato and malt extracts cultures of shiitake TMI-563 and 655 at 25 degrees C for a prolonged period. The main results on the basis of a functional group analysis and gel-filtration of NDL before and after the enzymatic degradation showed that the degraded DL had a higher content of phenolic OH groups than sound lignin, whereas the methoxyl or aromatic aldehyde-yielding group content was lower in the degraded lignin. The main degradation products formed from I in a crude enzyme solution were guaiacol, guaiacylglycerol, guaiacylglycol-beta-guaiacyl ether (II), and guaiacoxyacetoguaiacone (III), although the polymer was formed at pH 4.0, which is the optimum pH of peroxidase and laccase. It also was clarified that the oxidative polymerization of NDL and I occurred preferably in a crude enzyme solution at pH 4.0, and that these compounds were degraded to lower molecular fragments at pH 6.8 under the same conditions. From the above results, it is suggested that softwood lignin is more effectively degraded by the other enzyme than polyphenoloxidase, such as laccase and peroxidase, in a crude enzyme solution of L. edodes. (Refs. 9).

  1. Lithium alkyl anions of uranium(IV) and uranium(V)

    International Nuclear Information System (INIS)

    Sigurdson, E.R.; Wilkinson, G.

    1977-01-01

    Organouranium compounds with six or eight uranium-to-carbon sigma-bonds have been synthesized for the first time. The interaction of uranium tetrachloride with lithium alkyls in diethyl ether leads to the isolation of unstable lithium alkyluranate(IV) compounds of stoicheiometry Li 2 UR 6 .8Et 2 0 (R = Me, CH 2 SiMe 3 . Ph, and o-Me 2 NCH 2 C 6 H 4 ). These lithium salts can also be obtained with other donor solvents, such as tetrahydrofuran or NNN'N'-tetramethylethylenediamine. From uranium pentaethoxide similar lithium salts of stoicheiometry Li 3 UR 8 .3 dioxan (R = Me, CH 2 CMe 3 , and CH 2 SiMe 3 ) can be obtained. The interaction of uranium(VI) hexaisopropoxide with lithium, magnesium, or aluminium alkyls does not give compounds containing U-C bonds, but green oils, e.g. U(OPrsup(i)) 6 (MgMe 2 ) 3 , that appear to be adducts in which the oxygen atom of the isopropoxide group bound to uranium is acting as a donor. I.r. and n.m.r. spectroscopy and analytical data for the new compounds are presented. (author)

  2. Optimization of the fabrication of novel stealth PLA-based nanoparticles by dispersion polymerization using D-optimal mixture design.

    Science.gov (United States)

    Adesina, Simeon K; Wight, Scott A; Akala, Emmanuel O

    2014-11-01

    Nanoparticle size is important in drug delivery. Clearance of nanoparticles by cells of the reticuloendothelial system has been reported to increase with increase in particle size. Further, nanoparticles should be small enough to avoid lung or spleen filtering effects. Endocytosis and accumulation in tumor tissue by the enhanced permeability and retention effect are also processes that are influenced by particle size. We present the results of studies designed to optimize cross-linked biodegradable stealth polymeric nanoparticles fabricated by dispersion polymerization. Nanoparticles were fabricated using different amounts of macromonomer, initiators, crosslinking agent and stabilizer in a dioxane/DMSO/water solvent system. Confirmation of nanoparticle formation was by scanning electron microscopy (SEM). Particle size was measured by dynamic light scattering (DLS). D-optimal mixture statistical experimental design was used for the experimental runs, followed by model generation (Scheffe polynomial) and optimization with the aid of a computer software. Model verification was done by comparing particle size data of some suggested solutions to the predicted particle sizes. Data showed that average particle sizes follow the same trend as predicted by the model. Negative terms in the model corresponding to the cross-linking agent and stabilizer indicate the important factors for minimizing particle size.

  3. Ultrafast vibronic dynamics of dye molecules studied by the induced grating method

    International Nuclear Information System (INIS)

    Liu, C.H.; Troeger, P.; Laubereau, A.

    1985-08-01

    Previous work on transient polarization spectroscopy applying the induced grating technique concentrated on the time scale > 10 -11 s. Only one earlier study on a shorter time scale showed the occurrence of the so-called coherence peak without a detailed explanation for this phenomena. We report new theoretical and experimental data on a polarization effect that occurs in the nonlinear Rayleigh scattering of delayed probing pulses from induced population gratings. The periodic population changes are generated by two synchronized pumping pulses of the same frequency. Model calculations are presented, which carefully evaluate the orientational distribution and give quantitative information on the scattering signal for various polarization conditions. The scattering mechanism for the coherence peak is explained as a two step process with one photon absorption and emission process; it depends on the vibronic relaxation of the terminating level in the excited electronic state. Experimental results are reported for the vibrational and orientational relaxation times. For example values of tausub(v)=0.2+-0.2 ps and tausub(v)=0.8+-0.3 ps are measured respectively for Rhodamine 6G in ethanol and phenoxazone 9 in dioxane. Our three-beam transient grating technique under general polarization conditions can be used for the study of a variety of dynamic processes of molecules in the excited electronic or ground state. An important advantage compared to nonlinear absorption or induced dichroism techniques is that the scattering method avoids undesirable background signals. (author)

  4. Thermophysical properties of binary mixtures of N,N-dimethylformamide with three cyclic ethers

    Directory of Open Access Journals (Sweden)

    Sinha Biswajit

    2013-01-01

    Full Text Available Densities and viscosities of the binary mixtures consisting of tetrahydrofuran (THF, 1,3-dioxolane (1,3-DO and 1,4-dioxane (1,4-DO with N,N-dimethylformamide (DMF over the entire range of composition were measured at temperatures 298.15, 308.15 and 318.15 K and at atmospheric pressure. Ultrasonic speeds of sound of these binary mixtures were measured at ambient temperature and atmospheric pressure (T = 298.15 K and P = 1.01×105 Pa. The various experimental data were utilized to derive excess molar volumes (VmE, excess viscosities (ηE, and excess isentropic compressibilities (κsE. Using the excess molar volumes (VmE, excess partial molar volumes (and and excess partial molar volumes at infinite dilution (and of each liquid component in the mixtures were derived and discussed. Excess molar volumes (VmE as a function of composition at ambient temperature and atmospheric pressure were used further to test the applicability of the Prigogine-Flory-Patterson (PFP theory to the experimental binaries. The excess properties were found to be either negative or positive depending on the nature of molecular interactions and structural effects of liquid mixtures. Em,1V Em,2VE0,m,1VE0,m,2V.

  5. Phosphazene-catalyzed ring-opening polymerization of ε-caprolactone: Influence of solvents and initiators

    KAUST Repository

    Alamri, Haleema; Zhao, Junpeng; Pahovnik, David; Hadjichristidis, Nikolaos

    2014-01-01

    Phosphazene base (t-BuP2) catalysed metal-free ring-opening polymerization of ε-caprolactone (ε-CL) at room temperature with various protic initiators in different solvents was investigated. The polymerization proceeded, in most cases, in a controlled manner to afford poly(ε-caprolactone) with low dispersities and expected molecular weights. Kinetic studies showed that when a primary alcohol was used as an initiator the polymerization rate in different solvents followed the order of dichloromethane ≫ toluene > 1,4-dioxane ≈ tetrahydrofuran. Extremely fast polymerization of l-lactide (LLA), which was added as a second monomer, was observed in different solvents giving rise to poly(ε-caprolactone)-b- poly(l-lactide) diblock copolymers with neat PLLA blocks despite incomplete conversion of ε-CL. The dependence of polymerization rate on the concentrations of ε-CL and t-BuP2 was also revealed. In addition to primary alcohol, the feasibility of using other protic initiators, such as secondary alcohol (either on a small molecule or a polymer chain-end), (aliphatic/aromatic) amide, carboxylic acid, phenol and thiophenol, was also investigated. These studies provided important information for designing a metal-free route towards polyester-based (bio)materials. © 2014 the Partner Organisations.

  6. Poly(ethylene glycol)-grafted cyclic acetals based polymer networks with non-water-swellable, biodegradable and surface hydrophilic properties

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Ruixue, E-mail: qdruinyan@hotmail.com [Complex and Intelligent Research Center, School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai (China); Zhang, Nan; Wu, Wentao [School of Materials Science and Engineering, Changzhou University, Changzhou 213164 (China); Wang, Kemin, E-mail: kemin-wang@hotmail.com [School of Materials Science and Engineering, Changzhou University, Changzhou 213164 (China)

    2016-05-01

    Cyclic acetals based biomaterial without acidic products during hydrolytic degradation is a promising candidate for tissue engineering applications; however, low hydrophilicity is still one limitation for its biomedical application. In this work, we aim to achieve non-water-swellable cyclic acetal networks with improved hydrophilicity and surface wettability by copolymerization of cyclic acetal units based monomer, 5-ethyl-5-(hydroxymethyl)-β,β-dimethyl-1, 3-dioxane-2-ethanol diacrylate (EHD) and methoxy poly(ethylene glycol) monoacrylate (mPEGA) under UV irradiation, to avoid swelling of conventional hydrogels which could limit their applicability in particular of the mechanical properties and geometry integrity. Various EHD/mPEGA networks were fabricated with different concentrations of mPEGA from 0 to 30%, and the results showed photopolymerization behavior, mechanical property and thermal stability could not be significantly affected by addition of mPEGA, while the surface hydrophilicity was dramatically improved with the increase of mPEGA and could achieve a water contact angle of 37° with 30% mPEGA concentration. The obtained EHD/mPEGA network had comparative degradation rate to the PECA hydrogels reported previously, and MTT assay indicated it was biocompatible to L929 cells. - Highlights: • Cyclic acetals contained EHD/mPEGA networks were fabricated by photopolymerization. • It can be degraded under simulated physiological condition without acidic products. • Surface hydrophilicity was increased without swelling in water.

  7. Fabrication and Characterization of 3D-Printed Highly-Porous 3D LiFePO4 Electrodes by Low Temperature Direct Writing Process

    Directory of Open Access Journals (Sweden)

    Changyong Liu

    2017-08-01

    Full Text Available LiFePO4 (LFP is a promising cathode material for lithium-ion batteries. In this study, low temperature direct writing (LTDW-based 3D printing was used to fabricate three-dimensional (3D LFP electrodes for the first time. LFP inks were deposited into a low temperature chamber and solidified to maintain the shape and mechanical integrity of the printed features. The printed LFP electrodes were then freeze-dried to remove the solvents so that highly-porous architectures in the electrodes were obtained. LFP inks capable of freezing at low temperature was developed by adding 1,4 dioxane as a freezing agent. The rheological behavior of the prepared LFP inks was measured and appropriate compositions and ratios were selected. A LTDW machine was developed to print the electrodes. The printing parameters were optimized and the printing accuracy was characterized. Results showed that LTDW can effectively maintain the shape and mechanical integrity during the printing process. The microstructure, pore size and distribution of the printed LFP electrodes was characterized. In comparison with conventional room temperature direct ink writing process, improved pore volume and porosity can be obtained using the LTDW process. The electrochemical performance of LTDW-fabricated LFP electrodes and conventional roller-coated electrodes were conducted and compared. Results showed that the porous structure that existed in the printed electrodes can greatly improve the rate performance of LFP electrodes.

  8. Preparation and Characterization of Styrene Bearing Diethanolamine Side Group, Styrene Copolymer Systems, and Their Metal Complexes

    Directory of Open Access Journals (Sweden)

    Aslışah Açıkses

    2018-01-01

    Full Text Available The two copolymer systems of styrene bearing diethanol amine side group and styrene were prepared by free radical polymerization method at 60°C in presence of 1,4-dioxane as solvent and AIBN as initiator. Their metal complexes were prepared by reaction of the copolymer used as ligand P(DEAMSt-co-StL′′ and Ni(II and Co(II metal ions, which was carried out in presence of ethanol and NaOH at 65°C for 48 h in pH = 7.5. The structures of the copolymers used as ligand and metal complexes were identified by FT-IR, 1H-NMR spectra, and elemental analysis. The properties of the copolymers used as ligand and metal complexes were characterized by SEM-EDX, AAS, DSC, TGA, and DTA techniques. Then, the electrical properties of the copolymers and metal complexes were examined as a function of the temperature and frequency, and the activation energies (Ea were estimated with conductivity measurements.

  9. Supramolecular Assemblies from Poly(styrene-block-poly(4-vinylpyridine Diblock Copolymers Mixed with 6-Hydroxy-2-naphthoic Acid

    Directory of Open Access Journals (Sweden)

    Jean-François Gohy

    2013-06-01

    Full Text Available Supramolecular assemblies involving interaction of a small organic molecule, 2-hydroxy-6-Naphthoic acid (HNA, with poly(styrene-block-poly(4-vinylpyridine (PS-b-P4VP diblock copolymers are utilized to obtain micellar structures in solution, nanostructured thin films on flat substrates and, finally, nanoporous thin films. The formation of hydrogen bonds between HNA and the poly(4-vinylpyridine (P4VP blocks is confirmed by spectroscopic measurements. The accordingly P4VP/HNA hydrogen-bonded complexes are poorly soluble in 1,4-dioxane, resulting in the formation of micellar structures with a P4VP/HNA core and a polystyrene (PS corona. Those micelles have been spin-coated onto silicon wafers, resulting in nanostructured thin films consisting of P4VP/HNA dot-like features embedded in a PS matrix. The morphology of those films has been tuned by solvent annealing. Selective dissolution of HNA by methanol results in the formation of a nanoporous thin film. The P4VP/HNA nanodomains have been also cross-linked by borax, and the thin films have been further dissolved in a good solvent for PS, leading to micelles with a structure reminiscent of the thin films.

  10. In vitro toxicities of experimental jet fuel system ice-inhibiting agents.

    Science.gov (United States)

    Geiss, K T; Frazier, J M

    2001-07-02

    One research emphasis within the Department of Defense has been to seek the replacement of operational compounds with alternatives that pose less potential risk to human and ecological systems. Alternatives to glycol ethers, such as diethylene glycol monomethyl ether (M-DE), were investigated for use as jet fuel system ice-inhibiting agents (FSIIs). This group of chemicals includes three derivatives of 1,3-dioxolane-4-methanol (M-1, M-2, and M-3) and a 1,3-dioxane (M-27). In addition, M-DE was evaluated as a reference compound. Our approach was to implement an in vitro test battery based on primary rat hepatocyte cultures to perform initial toxicity evaluations. Hepatocytes were exposed to experimental chemicals (0, 0.001, 0.01, 0.1, 1, 10 mM dosages) for periods up to 24 h. Samples were assayed for lactate dehydrogenase (LDH) release, MTT dye reduction activity, glutathione level, and rate of protein synthesis as indicators of toxicity. Of the compounds tested, M-1, especially at the 10-mM dose, appeared to be more potent than the other chemicals, as measured by these toxicity assays. M-DE, the current FSII, elicited little response in the toxicity assays. Although some variations in toxicity were observed at the 10-mM dose, the in vitro toxicities of the chemicals tested (except for M-1) were not considerably greater than that of M-DE.

  11. Occupational exposure to airborne chemical substances in paintings conservators

    Directory of Open Access Journals (Sweden)

    Anna Jeżewska

    2014-02-01

    Full Text Available Background: This paper presents the results of the quantitative study of the airborne chemical substances detected in the conservator's work environment. Material and Methods: The quantitative tests were carried out in 6 museum easel paintings conservation studios. The air test samples were taken at various stages of restoration works, such as cleaning, doubling, impregnation, varnishing, retouching, just to name a few. The chemical substances in the sampled air were measured by the GC-FID (gas chromatography with flame ionization detector test method. Results: The study results demonstrated that concentrations of airborne substances, e.g., toluene, 1,4-dioxane, turpentine and white spirit in the work environment of paintings conservators exceeded the values allowed by hygiene standards. It was found that exposure levels to the same chemical agents, released during similar activities, varied for different paintings conservation studios. It is likely that this discrepancy resulted from the indoor air exchange system for a given studio (e.g. type of ventilation and its efficiency, the size of the object under maintenance, and also from the methodology and protection used by individual employees. Conclusions: The levels of organic solvent vapors, present in the workplace air in the course of painting conservation, were found to be well above the occupational exposure limits, thus posing a threat to the worker's health. Med Pr 2014;65(1:33–41

  12. Structural and functional characterization of the CAP domain of pathogen-related yeast 1 (Pry1) protein

    Science.gov (United States)

    Darwiche, Rabih; Kelleher, Alan; Hudspeth, Elissa M.; Schneiter, Roger; Asojo, Oluwatoyin A.

    2016-06-01

    The production, crystal structure, and functional characterization of the C-terminal cysteine-rich secretory protein/antigen 5/pathogenesis related-1 (CAP) domain of pathogen-related yeast protein-1 (Pry1) from Saccharomyces cerevisiae is presented. The CAP domain of Pry1 (Pry1CAP) is functional in vivo as its expression restores cholesterol export to yeast mutants lacking endogenous Pry1 and Pry2. Recombinant Pry1CAP forms dimers in solution, is sufficient for in vitro cholesterol binding, and has comparable binding properties as full-length Pry1. Two crystal structures of Pry1CAP are reported, one with Mg2+ coordinated to the conserved CAP tetrad (His208, Glu215, Glu233 and His250) in spacegroup I41 and the other without divalent cations in spacegroup P6122. The latter structure contains four 1,4-dioxane molecules from the crystallization solution, one of which sits in the cholesterol binding site. Both structures reveal that the divalent cation and cholesterol binding sites are connected upon dimerization, providing a structural basis for the observed Mg2+-dependent sterol binding by Pry1.

  13. Fabrication and Characterization of 3D-Printed Highly-Porous 3D LiFePO₄ Electrodes by Low Temperature Direct Writing Process.

    Science.gov (United States)

    Liu, Changyong; Cheng, Xingxing; Li, Bohan; Chen, Zhangwei; Mi, Shengli; Lao, Changshi

    2017-08-10

    LiFePO₄ (LFP) is a promising cathode material for lithium-ion batteries. In this study, low temperature direct writing (LTDW)-based 3D printing was used to fabricate three-dimensional (3D) LFP electrodes for the first time. LFP inks were deposited into a low temperature chamber and solidified to maintain the shape and mechanical integrity of the printed features. The printed LFP electrodes were then freeze-dried to remove the solvents so that highly-porous architectures in the electrodes were obtained. LFP inks capable of freezing at low temperature was developed by adding 1,4 dioxane as a freezing agent. The rheological behavior of the prepared LFP inks was measured and appropriate compositions and ratios were selected. A LTDW machine was developed to print the electrodes. The printing parameters were optimized and the printing accuracy was characterized. Results showed that LTDW can effectively maintain the shape and mechanical integrity during the printing process. The microstructure, pore size and distribution of the printed LFP electrodes was characterized. In comparison with conventional room temperature direct ink writing process, improved pore volume and porosity can be obtained using the LTDW process. The electrochemical performance of LTDW-fabricated LFP electrodes and conventional roller-coated electrodes were conducted and compared. Results showed that the porous structure that existed in the printed electrodes can greatly improve the rate performance of LFP electrodes.

  14. Surface-modified functionalized polycaprolactone scaffolds for bone repair

    DEFF Research Database (Denmark)

    Jensen, Jonas; Rölfing, Jan Hendrik Duedal; Svend Le, Dang Quang

    2014-01-01

    A porcine calvaria defect study was carried out to investigate the bone repair potential of three-dimensional (3D)-printed poly-ε-caprolactone (PCL) scaffolds embedded with nanoporous PCL. A microscopic grid network was created by rapid prototyping making a 3D-fused deposition model (FDM-PCL). Af......A porcine calvaria defect study was carried out to investigate the bone repair potential of three-dimensional (3D)-printed poly-ε-caprolactone (PCL) scaffolds embedded with nanoporous PCL. A microscopic grid network was created by rapid prototyping making a 3D-fused deposition model (FDM......-PCL). Afterward, the FDM-PCL scaffolds were infused with a mixture of PCL, water, and 1,4-dioxane and underwent a thermal-induced phase separation (TIPS) followed by lyophilization. The TIPS process lead to a nanoporous structure shielded by the printed microstructure (NSP-PCL). Sixteen Landrace pigs were divided...... into two groups with 8 and 12 weeks follow-up, respectively. A total of six nonpenetrating holes were drilled in the calvaria of each animal. The size of the cylindrical defects was h 10 mm and Ø 10 mm. The defects were distributed randomly using following groups: (a) NSP-PCL scaffold, (b) FDM-PCL scaffold...

  15. Thin nanostructured crystalline TiO{sub 2} films and their applications in solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Cheng Yajun

    2007-06-15

    Research on thin nanostructured crystalline TiO{sub 2} films has attracted considerable interests because of their intriguing physical properties and potential applications in photovoltaics. Nanostructured TiO{sub 2} film plays an important role in the TiO{sub 2} based dye-sensitized solar cells because they act as a substrate for the adsorption of dye molecules and a matrix for the transportation of electrons as well. Thus they can influence the solar cell performance significantly. Consequently, the control of the morphology including the shape, size and size distribution of the TiO{sub 2} nanostructures is critical to tune and optimize the performance of the solar cells. To control the TiO{sub 2} morphology, a strategy using amphiphilic block copolymer as templating agent coupled with sol-gel chemistry has been applied. Especially, a good-poor solvent pair induced phase separation process has been developed to guide the microphase separation behavior of the block copolymers. The amphiphilic block copolymers used include polystyrene-block-poly (ethylene oxide) (PS-b-PEO), poly (methyl methacrylate)-block-poly (ethylene oxide) (PMMA-b-PEO), and poly (ethylene oxide)-block-polystyrene-block-poly (ethylene oxide) (PEO-b-PS-b-PEO). The block copolymer undergoes a good-poor-solvent pair induced phase separation in a mixed solution of 1, 4-dioxane or N, N-dimethyl formamide (DMF), concentrated hydrochloric acid (HCl) and Titanium tetraisopropoxide (TTIP). Specifically, in the system of PS-b-PEO, a morphology phase diagram of the inorganic-copolymer composite films was mapped by adjusting the weight fractions among 1, 4-dioxane, HCl, and TTIP in solution. The amorphous TiO{sub 2} within the titania-block copolymer composite films was crystallized by calcination at temperatures above 400 C, where the organic block copolymer was simultaneously burned away. This strategy is further extended to other amphiphilic block copolymers of PMMA-b-PEO and PEO-b-PS-b-PEO, where the

  16. Effects of iron type in Fenton reaction on mineralization and biodegradability enhancement of hazardous organic compounds.

    Science.gov (United States)

    Khan, Eakalak; Wirojanagud, Wanpen; Sermsai, Nawarat

    2009-01-30

    The mineralization and biodegradability increase and their combination of two traditional and two relatively new organic contaminants by Fenton reagents with three different types of iron, Fe(2+), Fe(3+), and Fe(0) were investigated. The traditional contaminants examined were trichloroethene (TCE) and 2,4-dichlorophenol (2,4-DCP) while 1,4-dioxane (1,4-D) and 1,2,3-trichloropropane (TCP) were studied for the relatively new contaminants. The mineralization and biodegradability were represented by dissolved organic carbon (DOC) reduction and the ratio of biodegradable dissolved organic carbon and DOC, respectively. For all four contaminants, Fenton reagent using Fe(2+) was more effective in the DOC reduction than Fenton reagents using Fe(3+) and Fe(0) in most cases. The types of Fe that provided maximum biodegradability increase were not the same for all four compounds, Fe(3+) for TCE, Fe(0) for 2,4-DCP, Fe(2+) for 1,4-D, and Fe(3+) for TCP. When the combination of DOC elimination and biodegradability increase (least refractory fraction) was considered, Fe(2+) was the best choice except for 2,4-DCP which was susceptible to Fe(0) catalyzed Fenton reagent the most. The least refractory fractions remaining after 120 min of reaction were 20-25% for TCE, 2,4-DCP, and TCP and 30-40% for 1,4-D. The iron type in Fenton reaction also affected the type of mineralization kinetics of TCE, 2,4-DCP, and TCP as well as the types of degradation by-products of these contaminants. Some of the by-products found, such as isopropanol and propionic aldehyde, which were produced from Fe(0) catalyzed Fenton degradation of TCP, have not been previously reported.

  17. Research on the structure in solution of optically active synthetic polymers (propylene polysulphide, propylene polyoxide, tertio-butyl polysulphide)

    International Nuclear Information System (INIS)

    Sarrazin, Brigitte

    1971-03-01

    It was proposed to study the structure of sulphur-containing synthetic polymers, stereo-regular, optically active in solution and able to adopt a spiral conformation, with special reference to propylene polysulphide. Two methods were used, the first mathematical (conformational energy calculations) and the second physico-chemical, essentially spectroscopic. By conformational analysis it is possible to choose the most probable structures liable to be adopted by a given polymer in solution while the spectro-polarimetric study should, in principle, invalidate or confirm certain of these hypotheses. The conformational energy calculations showed that in fact there is no energy conformation low enough to be stable in solution. Strictly speaking however we can refer to a region of stability in which steric hindrance is low and many energy minima exist. These minima are indistinguishable both by their energy values and by their spatial localizations and are all enclosed in the region bounded by the barriers due to steric hindrance. This uncertainty does not arise from approximations made in the calculations, but from the multitude of stereochemical structure possible. Investigations into the variation of the optical rotary dispersion and the circular dichroism as a function of temperature indicated the existence of three or more equilibrium states in the dioxane. The spectra appear to be the summation of the optical activities of the numerous simultaneously possible conformations. It appears that polymers, such as propylene polysulphide or propylene polyoxide do not have stable structures in solution. These are molecules of great flexibility possessing a large number of degrees of freedom. These properties distinguish them from the natural polymers, carrying precise information, such as DNA which must consequently have stable conformations. (author) [fr

  18. Characterizing the selectivity of stationary phases and organic modifiers in reversed-phase high-performance liquid chromatographic systems by a general solvation equation using gradient elution.

    Science.gov (United States)

    Du, C M; Valko, K; Bevan, C; Reynolds, D; Abraham, M H

    2000-11-01

    Retention data for a set of 69 compounds using rapid gradient elution are obtained on a wide range of reversed-phase stationary phases and organic modifiers. The chromatographic stationary phases studied are Inertsil (IN)-ODS, pentafluorophenyl, fluoro-octyl, n-propylcyano, Polymer (PLRP-S 100), and hexylphenyl. The organic solvent modifiers are 2,2,2-trifluoroethanol (TFE); 1,1,1,3,3,3-hexafluoropropan-2-ol (HFIP); isopropanol; methanol (MeOH); acetonitrile (AcN); tetrahydrofuran; 1,4-dioxane; N,N-dimethylformamide; and mixed solvents of dimethylsulfoxide (DMSO) with AcN and DMSO with MeOH (1:1). A total of 25 chromatographic systems are analyzed using a solvation equation. In general, most of the systems give reasonable statistics. The selectivity of the reversed phase-high-performance liquid chromatographic (HPLC) systems with respect to the solute's dipolarity-polarity, hydrogen-bond acidity, and basicity are reflected in correspondingly large coefficients in the solvation equation. We wanted to find the most orthogonal HPLC systems, showing the highest possible selectivity difference in order to derive molecular descriptors using the gradient retention times of a compound. We selected eight chromatographic systems that have a large range of coefficients of interest (s, a, and b) similar to those found in water-solvent partitions used previously to derive molecular descriptors. The systems selected are IN-ODS phases with AcN, MeOH, TFE, and HFIP as mobile phase, PLRP-S 100 phase with AcN, propylcyano phase with AcN and MeOH, and fluorooctyl phase with TFE. Using the retention data obtained for a compound in the selected chromatographic systems, we can estimate the molecular descriptors with the faster and simpler gradient elution method.

  19. [Application of predictive model to estimate concentrations of chemical substances in the work environment].

    Science.gov (United States)

    Kupczewska-Dobecka, Małgorzata; Czerczak, Sławomir; Jakubowski, Marek; Maciaszek, Piotr; Janasik, Beata

    2010-01-01

    Based on the Estimation and Assessment of Substance Exposure (EASE) predictive model implemented into the European Union System for the Evaluation of Substances (EUSES 2.1.), the exposure to three chosen organic solvents: toluene, ethyl acetate and acetone was estimated and compared with the results of measurements in workplaces. Prior to validation, the EASE model was pretested using three exposure scenarios. The scenarios differed in the decision tree of pattern of use. Five substances were chosen for the test: 1,4-dioxane tert-methyl-butyl ether, diethylamine, 1,1,1-trichloroethane and bisphenol A. After testing the EASE model, the next step was the validation by estimating the exposure level and comparing it with the results of measurements in the workplace. We used the results of measurements of toluene, ethyl acetate and acetone concentrations in the work environment of a paint and lacquer factory, a shoe factory and a refinery. Three types of exposure scenarios, adaptable to the description of working conditions were chosen to estimate inhalation exposure. Comparison of calculated exposure to toluene, ethyl acetate and acetone with measurements in workplaces showed that model predictions are comparable with the measurement results. Only for low concentration ranges, the measured concentrations were higher than those predicted. EASE is a clear, consistent system, which can be successfully used as an additional component of inhalation exposure estimation. If the measurement data are available, they should be preferred to values estimated from models. In addition to inhalation exposure estimation, the EASE model makes it possible not only to assess exposure-related risk but also to predict workers' dermal exposure.

  20. Protective Effect of Nigella Sativa Black Seed Oil And Freshly Crushed Seeds In Rats During Tumour Induction And Radiotherapy

    International Nuclear Information System (INIS)

    Abdallah, N.M.; Eldosoky, H.M.; Mohamed, H.E.; Noaman, E.

    2006-01-01

    The present study was conducted to evaluate the potency of Nigella sativa freshly crushed seeds (0.42 g/ kg body weight) or oil (2.5 ml/kg body weight) for preventing tumor induction through exposure of rats to a common pollutant (1,4- Dioxane) as a promoter under condition of the presence of an initiator (N-nitrosodiethylamine). The antitumor effect was evaluated alone or in combination with low doses of irradiation as a route of cancer treatment. Female Swiss albino rats were administrated orally twice weekly with Nigella sativa before and during exposure of rats to the carcinogenic compounds. Animals were exposed to 3 doses of radiation (3 Gy/ dose) day after day 2 weeks before the end of the experiment. The animals were scarified after one week of radiation. Homocysteine,'glutathione, lipid peroxide, GGT activity, nitric oxide, total protein, albumin and bilirubin levels were estimated in blood after 7 and 12 months from the start of the experiment. Rats injected with the carcinogenic compounds showed marked elevation in homocysteine, GGT activity, nitric oxide, bilirubin and lipid peroxide levels accompanied by a significant decrease in glutathione, total proteins and albumin levels. Pretreatment with Nigella sativa alone or combined with γ- irradiation potentially reversed the investigated parameters. Moreover, Nigella sativa significantly suppressed the growth of the tumor and efficiently produced synergistic effect with γ-irradiation. Therefore, Nigella sativa may be a good candidate to prevent tumor induction and so, it is advicable to use freshly crushed seeds during irradiation treatment in cancer patients as they gave more effective protection than the oil extract.

  1. Di-hydroxyurea-a Promising Reducing Reagent for the U/Pu split in the PUREX process

    Energy Technology Data Exchange (ETDEWEB)

    Taihong, Yan; Weifang, Zheng; Guoan, Ye; Yu, Zhang; Liang, Xian; Ying, Di; Xiaoyan, Bian [Department of Radiochemistry, China Institute of Atomic Energy - CIAE, Beijing 102413 (China)

    2009-06-15

    In the reprocessing of spent nuclear fuel by the Purex process, the separation of U and Pu is a major stage. This is commonly achieved by a redox process, in which a reducing agent (e.g. U(IV) or (FeII)) and a stabiliser (e.g. N{sub 2}H{sub 4} or NH{sub 2}SO{sub 3}H) are added to reduce extractable Pu{sup 4+} to un-extractable Pu{sup 3+}. The stabiliser prevents the nitrous acid catalysed re-oxidation of Pu(III) back to Pu(IV). One of the key objectives is to reduce both the number of solvent extraction cycles and the waste stream volumes [1]. One option for Advanced Purex flowsheets is to adopt a new salt-free reductant in the U/Pu split. Di-hydroxyurea(DHU)-a new Reducing reagent was synthesized with tri-associated solid phosgene (Bis(trichloromethyl)Carbonate) solved in dioxane and hydroxylamine hydrochloride solved in potassium acetate solution. The Reduction of Pu(IV) by DHU was investigated using UV-Vis spectrophotometer. The reduction back-extraction behavior of Pu(IV) in 30%TBP /OK was firstly investigated under conditions of different temperature, different concentration of DHU and HNO{sub 3} and various phase contract time respectively.The results showed that Pu(IV) in organic phase can be stripped rapidly to aqueous phase by DHU. Simulating the 1B contactor of the Purex process by DHU with nitric acid solution as the stripping agent,the separation factors of uranium/plutonium can reach 2.1 10{sup 4}. This indicates that DHU is a promising salt free agent for uranium/plutonium separation. (authors)

  2. In-situ burning of spilled oil

    International Nuclear Information System (INIS)

    Tennyson, E.J.

    1992-01-01

    This presentation provided an overview of results from the Minerals Management Service's (MMS) funded research on in situ burning of spilled oil. The program began in 1983 to determine the limitations of this innovative response strategies. Specific physical variables evaluated were slick thickness, degree of weathering (sparging), sea state, wind velocities, air and water temperatures, degrees of emulsification and degree of ice-coverage. All of the oils tested burned with 50 to 95 percent removal ratios as long as emulsification had not occurred. Slick thickness of 3mm or thicker were required to sustain ignition and extinguishment occurred when the slick reached approximately 1mm thick. The next phase of the research involved quantitative analysis of the pollutants created by in situ burning including chemical composition of the parent oil, burn residue, and airborne constituents. These studies were conducted at the National Institute of Standards and Technology (NIST) with emphasis on particulate, and gaseous components created by the burning process. Research efforts over several years, and a variety of crude oils, yielded data which indicated that aldehydes ketones, dioxans, furans, and polyaromatic compounds (PAHS) were not formed in the burning process. The airborne pollutants reflected similar concentrations of these compounds that were present in the parent oil. Lighter molecular weight PAHs tended to be converted to higher molecular weight compounds. Heavier molecular weight compounds are considered less acutely toxic than lighter molecular weight PAHS. Predominant burn products released into the air were by weight: 75% carbon dioxide, 12% water vapor, 10% soot, 3% carbon monoxide and 0.2% other products including those listed above

  3. Millimeter wave and terahertz dielectric properties of biological materials

    Science.gov (United States)

    Khan, Usman Ansar

    Broadband dielectric properties of materials can be employed to identify, detect, and characterize materials through their unique spectral signatures. In this study, millimeter wave, submillimeter wave, and terahertz dielectric properties of biological substances inclusive of liquids, solids, and powders were obtained using Dispersive Fourier Transform Spectroscopy (DFTS). Two broadband polarizing interferometers were constructed to test materials from 60 GHz to 1.2 THz. This is an extremely difficult portion of the frequency spectrum to obtain a material's dielectric properties since neither optical nor microwave-based techniques provide accurate data. The dielectric characteristics of liquids such as cyclohexane, chlorobenzene, benzene, ethanol, methanol, 1,4 dioxane, and 10% formalin were obtained using the liquid interferometer. Subsequently the solid interferometer was utilized to determine the dielectric properties of human breast tissues, which are fixed and preserved in 10% formalin. This joint collaboration with the Tufts New England Medical Center demonstrated a significant difference between the dielectric response of tumorous and non-tumorous breast tissues across the spectrum. Powders such as anthrax, flour, talc, corn starch, dry milk, and baking soda have been involved in a number of security threats and false alarms around the globe in the last decade. To be able to differentiate hoax attacks and serious security threats, the dielectric properties of common household powders were also examined using the solid interferometer to identify the powders' unique resonance peaks. A new sample preparation kit was designed to test the powder specimens. It was anticipated that millimeter wave and terahertz dielectric characterization will enable one to clearly distinguish one powder from the other; however most of the powders had relatively close dielectric responses and only Talc had a resonance signature recorded at 1.135 THz. Furthermore, due to

  4. A Simple Spectrophotometric Method for the Determination of Copper in Some Real, Environmental, Biological, Food and Soil Samples Using Salicylaldehyde Benzoyl Hydrazone

    Directory of Open Access Journals (Sweden)

    M. Jamaluddin Ahmed

    2012-06-01

    Full Text Available A very simple, ultra-sensitive, highly selective and non-extractive spectrophotometric method for the determination of trace amounts copper(II has been developed. Salicylaldehy debenzoyl hydrazone (SAL-BH has been proposed as a new analytical reagent for the direct non-extractive spectrophotometric determination of copper(II. SAL-BH reacts with copper in a slightly acidic (0.0001-0.005 M H2SO4 in 40% 1,4-dioxane media with copper(II to give a highly absorbent greenish yellow chelate with a molar ratio 1:1(CuII: SAL-BH The reaction is instantaneous and the maximum absorption was obtained at 404 nm and remains stable for 72 h. The average molar absorptivity and Sandell’s sensitivity were found to be 1.4×105 L mol-1 cm-1 and 5.0 ng cm-2 of copper(II, respectively. Linear calibration graphs were obtained for 0.01 – 18 mg L-1 of CuII. The detection limit and quantification limit of the reaction system were found to be 1 ng mL-1 and 10 µg L-1, respectively. A large excess of over 50 cations, anions and complexing agents (e.g., tartrate, oxalate, citrate, phosphate, thiocyanate etc. do not interfere in the determination. The method is highly selective for copper and was successfully used for the determination of copper in several standard reference materials (steels and alloys as well as in some environmental waters (portable and polluted, biological (human blood and urine, food and soil samples and solutions containing both copper(I and copper(II as well as some complex synthetic mixtures. The results of the proposed method for biological and food samples were comparable with AAS and were found to be in good agreement. The method has high precision and accuracy (s = ± 0.01 for 0.5 mg L-1.

  5. Micellization behaviour and thermodynamic parameters of 12-2-12 gemini surfactant in (water + organic solvent) mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Batigoec, Cigdem [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Akbas, Halide, E-mail: hakbas34@yahoo.com [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Boz, Mesut [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey)

    2011-09-15

    Highlights: > The cmc and {alpha} values of surfactant increased with increasing solvent content and temperature. > The values of ({Delta}G{sub m}{sup 0}) are negative in all cases for the micelle formation becomes less favourable. > The values of negative enthalpy indicate importance of the London dispersion forces for the micellization. > The positive entropy is due to a contribution supplied from the solvent. - Abstract: The effect of organic solvents on micellization behaviour and thermodynamic parameters of a cationic gemini (dimeric) surfactant, C{sub 12}H{sub 25}(CH{sub 3}){sub 2}N{sup +}-(CH{sub 2}){sub 2}-N{sup +}(CH{sub 3}){sub 2}C{sub 12}H{sub 25}.2Br{sup -}, (12-2-12) was studied in aqueous solutions over the range of T = (293.15 to 323.15) K using the conductometric technique. Ethylene glycol (EG), dimethylsulfoxide (DMSO) and 1,4-dioxan (DO) were used as organic solvents with three different contents. The critical micelle concentration (cmc) and the degree of counter ion dissociation ({alpha}) of micelles in the water and in the (water + organic solvent) mixtures including 10%, 20%, and 30% solvent contents were determined. The standard Gibbs free energy ({Delta}G{sub m}{sup 0}), enthalpy ({Delta}H{sub m}{sup 0}) and entropy ({Delta}S{sub m}{sup 0}) of micellization were estimated from the temperature dependence of the cmc values. It was observed that the critical micelle concentration of the gemini surfactant and the degree of counter ion dissociation of the micelle increased as the volume percentage of organic solvent, and temperature increased. The standard Gibbs free energy of micellization was found to be less negative with the increase in the organic solvent content and temperature.

  6. Peptide self-association in aqueous trifluoroethanol monitored by pulsed field gradient NMR diffusion measurements

    Energy Technology Data Exchange (ETDEWEB)

    Yao Shenggen [Biomolecular Research Institute (Australia); Howlett, Geoffrey J. [University of Melbourne, Department of Biochemistry and Molecular Biology (Australia); Norton, Raymond S. [Biomolecular Research Institute (Australia)

    2000-02-15

    Defining the self-association state of a molecule in solution can be an important step in NMR-based structure determination. This is particularly true of peptides, where there can be a relatively small number of long-range interactions and misinterpretation of an intermolecular NOE as an intramolecular contact can have a dramatic influence on the final calculated structure. In this paper, we have investigated the use of translational self-diffusion coefficient measurements to detect self-association in aqueous trifluoroethanol of three peptides which are analogues of the C-terminal region of human neuropeptide Y. Experimentally measured diffusion coefficients were extrapolated to D{sup 0}, the limiting value as the peptide concentration approaches zero, and then converted to D{sub 20,w}, the diffusion coefficient after correction for temperature and the viscosity of the solvent. A decrease in D{sub 20,w} of about 16% was found for all three peptides in aqueous TFE (30% by volume) compared with water, which is in reasonable agreement with the expected decrease upon dimerisation, the presence of which was indicated by sedimentation equilibrium measurements. Apparent molecular masses of these peptides in both solutions were also calculated from their diffusion coefficients and similar results were obtained. Several potential internal standards, including acetone, acetonitrile, dimethylsulfoxide and dioxane, were assessed as monitors of solution viscosity over a range of trifluoroethanol concentrations. Compared with independent measurements of viscosity, acetonitrile was the most accurate standard among these four. The practical limitations of a quantitative assessment of peptide self-association from translational diffusion coefficients measured by PFGNMR, including the calculation of apparent molecular mass, are also discussed.

  7. Assessment of the thermodynamic properties of poly(2,2,2-trifluoroethyl methacrylate) by inverse gas chromatography.

    Science.gov (United States)

    Papadopoulou, Stella K; Panayiotou, Costas

    2014-01-10

    The thermodynamic properties of poly(2,2,2-trifluoroethyl methacrylate) (PTFEMA) were determined by the aid of the inverse gas chromatography technique (IGC), at infinite dilution. The interactions between the polymer and 15 solvents were examined in the temperature range of 120-150 °C via the estimation of the thermodynamic sorption parameters, the parameters of mixing at infinite dilution, the weight fraction activity coefficients and the Flory-Huggins interaction parameters. Additionally, the total and the partial solubility parameters of PTFEMA were estimated. The findings of this work indicate that the type and strength of the intermolecular interactions between the polymer and the solvents are strongly depended on the functional groups of the polymer and the solvents. The proton acceptor character of the polymer is responsible for the preferential solubility of PTFEMA in chloroform which acts as a proton donor solvent. The results also reveal that the polymer is insoluble in alkanes and alcohols whereas it presents good miscibility with polar solvents, especially with 2-butanone, 2-pentanone and 1,4-dioxane. Furthermore, the total and dispersive solubility parameters appear diminishing upon temperature rise, whereas the opposite behavior is noticed for the polar and hydrogen bonding solubility parameters. The latter increase with temperature, probably, due to conformational changes of the polymer on the solid support. Finally, comparison of the solubilization profiles of fluorinated methacrylic polymers studied by IGC, leads to the conclusion that PTFEMA is more soluble compared to polymers with higher fluorine content. Copyright © 2013 Elsevier B.V. All rights reserved.

  8. Proposed changes in the classification of carcinogenic chemicals in the work area.

    Science.gov (United States)

    Neumann, H G; Thielmann, H W; Filser, J G; Gelbke, H P; Greim, H; Kappus, H; Norpoth, K H; Reuter, U; Vamvakas, S; Wardenbach, P; Wichmann, H E

    1997-12-01

    Carcinogenic chemicals in the work area are currently classified into three categories in Section III of the German List of MAK and BAT Values. This classification is based on qualitative criteria and reflects essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. It is proposed that these Categories--IIIA1, IIIA2, and IIIB--be retained as Categories 1, 2, and 3, to conform with EU regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, it is now proposed that these three categories be supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not convey a significant risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. It is proposed that chemicals known to act typically by nongenotoxic mechanisms and for which information is available that allows evaluation of the effects of low-dose exposures be classified in Category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose-response relationships and toxicokinetics and for which risk at low doses can be assessed will be classified in Category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for Category 4 (1,4-dioxane) and Category 5 (styrene) are presented. The proposed changes in classifying carcinogenic chemicals in the work area are presented for further discussion.

  9. Study on the decomposition mechanism of alkyl carbonate on lithium metal by pyrolysis-gas chromatography-mass spectroscopy

    Science.gov (United States)

    Mogi, Ryo; Inaba, Minoru; Iriyama, Yasutoshi; Abe, Takeshi; Ogumi, Zempachi

    The surface films formed on deposited lithium in electrolyte solutions based on ethylene carbonate (EC), diethyl carbonate (DEC), and dimethyl carbonate (DMC) were analyzed by pyrolysis-gas chromatography-mass spectroscopy (Py-GC-MS). In 1 M LiClO 4/EC, the main component of the surface film was easily hydrolyzed to give ethylene glycol after exposure to air, and hence was considered to have a chemical structure of ROCH 2CH 2OR', of which OR and OR' are OLi or OCO 2Li. Ethylene oxide, acetaldehyde, and 1,4-dioxane were detected in decomposition products, and they were considered to have been formed by pyrolysis of ROCH 2CH 2OR' in the pyrolyzer. The presence of ethanol in decomposition products confirmed that ring cleavage at the CH 2O bonds of EC occurs by one electron reduction. In addition, the presence of methanol implied the cleavage of the CC bond of EC upon reduction. From the surface films formed in 1 M LiClO 4/DEC and /DMC, ethanol and methanol, respectively, were detected, which suggested that corresponding lithium alkoxides and/or lithium alkyl carbonates were the main components. In 1 M LiClO 4/EC+DEC (1:1), EC dominantly decomposed to form the surface film. The surface film formed in 1 M LiPF 6/EC+DEC (1:1) contained a much smaller amount of organic compounds.

  10. Biodegradable copolymers carrying cell-adhesion peptide sequences.

    Science.gov (United States)

    Proks, Vladimír; Machová, Lud'ka; Popelka, Stepán; Rypácek, Frantisek

    2003-01-01

    Amphiphilic block copolymers are used to create bioactive surfaces on biodegradable polymer scaffolds for tissue engineering. Cell-selective biomaterials can be prepared using copolymers containing peptide sequences derived from extracellular-matrix proteins (ECM). Here we discuss alternative ways for preparation of amphiphilic block copolymers composed of hydrophobic polylactide (PLA) and hydrophilic poly(ethylene oxide) (PEO) blocks with cell-adhesion peptide sequences. Copolymers PLA-b-PEO were prepared by a living polymerisation of lactide in dioxane with tin(II)2-ethylhexanoate as a catalyst. The following approaches for incorporation of peptides into copolymers were elaborated. (a) First, a side-chain protected Gly-Arg-Gly-Asp-Ser-Gly (GRGDSG) peptide was prepared by solid-phase peptide synthesis (SPPS) and then coupled with delta-hydroxy-Z-amino-PEO in solution. In the second step, the PLA block was grafted to it via a controlled polymerisation of lactide initiated by the hydroxy end-groups of PEO in the side-chain-protected GRGDSG-PEO. Deprotection of the peptide yielded a GRGDSG-b-PEO-b-PLA copolymer, with the peptide attached through its C-end. (b) A protected GRGDSG peptide was built up on a polymer resin and coupled with Z-carboxy-PEO using a solid-phase approach. After cleavage of the delta-hydroxy-PEO-GRGDSG copolymer from the resin, polymerisation of lactide followed by deprotection of the peptide yielded a PLA-b-PEO-b-GRGDSG block copolymer, in which the peptide is linked through its N-terminus.

  11. Port wine oxidation management: a multiparametric kinetic approach.

    Science.gov (United States)

    Martins, Rui Costa; Monforte, Ana Rita; Silva Ferreira, António

    2013-06-05

    Port wine is a flagship fortified wine of Portugal, which undergoes a particularly long aging period, developing a dynamic sensory profile over time, responsible for several wine categories, which is dependent upon the type of aging (bottle or barrel). Therefore, the quality of the product is dependent upon the chemical mechanisms occurring during the aging process, such as oxidation or Maillard reactions. To attain the desired quality management, it is necessary to understand how technological parameters, such as temperature or oxygen exposure, affect the kinetics of the formation of key odorants, such as sotolon. There is a lack of information about the impact of the storage conditions (oxygen and temperature) on Port wine quality. In this study, the effect of these two parameters were investigated to increase the knowledge database concerning aging management of Port wines. It was found that sotolon formation is highly dependent upon oxygen and temperature. There is however a synergistic effect between these two parameters that could significantly increase the concentration. The kinetic parameters of oxygen, sotolon, and other compounds related to Port aging (cis- and trans-5-hydroxy-2-methyl-1,3-dioxan, 2-furfural, 5-hydroxy-methyl-furfural, and 5-methyl-furfural) are also reported. Kinetic models with Monte Carlo simulations, where the oxygen permeability dispersion and temperature are the parameters under evaluation, were applied. On the basis of the modeling predictions, it would seem that the temperature of a cellar would have a more significant impact on the Port wines stored in containers where the oxygen intake is higher (barrels) when compared to containers with low oxygen permeability (bottles using cork stoppers).

  12. Combined use of titration calorimetry and spectrofluorimetry for the screening of the acidity of solid catalysts in different liquids

    International Nuclear Information System (INIS)

    Gervasini, Antonella; Auroux, Aline

    2013-01-01

    Graphical abstract: Measurements of acidity of oxides of catalytic importance in various liquids open the possibility to know their effective acidity, which is related with their activity in liquid-heterogeneous catalysis. Titration-calorimetry alone or in connection with spectrofluorimetry is efficient for this scope. - Highlights: • Measurements of acidity of oxides of catalytic importance in various liquids. • Titration-calorimetry alone or in connection with spectrofluorimetry is efficient for this scope. • Effective acidities are expressed by given sample in various liquids. • Nb-containing samples are able to maintain acidity in protic liquids. - Abstract: The effective acid and base surface properties of selected acidic and basic samples of catalytic interest (alumina, titania, zirconia, silica–alumina, niobium oxide, niobium phosphate, boron nitride, and hydrotalcite) were measured by titration with basic and acidic molecular probes (aniline, 2-phenylethylamine, and phenol) in various liquids (cyclohexane, 1,4-dioxane, isopropanol, n-decane, and toluene) with different polar and protic characteristics. The combined use of a reaction calorimeter and a spectrofluorimeter has been performed. The set-up of the coupled technique and the most interesting results are shown here. The study confirmed that the acid–base properties of solids are deeply affected by the nature and properties of the liquid surrounding the samples. Few oxides are able to maintain their surface acidity in highly polar and protic solvents, in particular whose containing niobium. In general, the solvating and coordinative ability of the most polar and protic liquids caused remarkable loss of acidity/basicity of the oxide surfaces

  13. Combined use of titration calorimetry and spectrofluorimetry for the screening of the acidity of solid catalysts in different liquids

    Energy Technology Data Exchange (ETDEWEB)

    Gervasini, Antonella, E-mail: antonella.gervasini@unimi.it [Dipartimento di Chimica, Università degli Studi di Milano, via Camillo Golgi, 19, 20133 Milano (Italy); Auroux, Aline, E-mail: aline.auroux@ircelyon.univ-lyon1.fr [Université Lyon 1, CNRS, UMR 5256, Institut de Recherches sur la Catalyse et l‘Environnement de Lyon (IRCELYON), 2 Avenue A. Einstein, 69626 Villeurbanne (France)

    2013-09-10

    Graphical abstract: Measurements of acidity of oxides of catalytic importance in various liquids open the possibility to know their effective acidity, which is related with their activity in liquid-heterogeneous catalysis. Titration-calorimetry alone or in connection with spectrofluorimetry is efficient for this scope. - Highlights: • Measurements of acidity of oxides of catalytic importance in various liquids. • Titration-calorimetry alone or in connection with spectrofluorimetry is efficient for this scope. • Effective acidities are expressed by given sample in various liquids. • Nb-containing samples are able to maintain acidity in protic liquids. - Abstract: The effective acid and base surface properties of selected acidic and basic samples of catalytic interest (alumina, titania, zirconia, silica–alumina, niobium oxide, niobium phosphate, boron nitride, and hydrotalcite) were measured by titration with basic and acidic molecular probes (aniline, 2-phenylethylamine, and phenol) in various liquids (cyclohexane, 1,4-dioxane, isopropanol, n-decane, and toluene) with different polar and protic characteristics. The combined use of a reaction calorimeter and a spectrofluorimeter has been performed. The set-up of the coupled technique and the most interesting results are shown here. The study confirmed that the acid–base properties of solids are deeply affected by the nature and properties of the liquid surrounding the samples. Few oxides are able to maintain their surface acidity in highly polar and protic solvents, in particular whose containing niobium. In general, the solvating and coordinative ability of the most polar and protic liquids caused remarkable loss of acidity/basicity of the oxide surfaces.

  14. Quantitative mapping of chemical compositions with MRI using compressed sensing.

    Science.gov (United States)

    von Harbou, Erik; Fabich, Hilary T; Benning, Martin; Tayler, Alexander B; Sederman, Andrew J; Gladden, Lynn F; Holland, Daniel J

    2015-12-01

    In this work, a magnetic resonance (MR) imaging method for accelerating the acquisition time of two dimensional concentration maps of different chemical species in mixtures by the use of compressed sensing (CS) is presented. Whilst 2D-concentration maps with a high spatial resolution are prohibitively time-consuming to acquire using full k-space sampling techniques, CS enables the reconstruction of quantitative concentration maps from sub-sampled k-space data. First, the method was tested by reconstructing simulated data. Then, the CS algorithm was used to reconstruct concentration maps of binary mixtures of 1,4-dioxane and cyclooctane in different samples with a field-of-view of 22mm and a spatial resolution of 344μm×344μm. Spiral based trajectories were used as sampling schemes. For the data acquisition, eight scans with slightly different trajectories were applied resulting in a total acquisition time of about 8min. In contrast, a conventional chemical shift imaging experiment at the same resolution would require about 17h. To get quantitative results, a careful weighting of the regularisation parameter (via the L-curve approach) or contrast-enhancing Bregman iterations are applied for the reconstruction of the concentration maps. Both approaches yield relative errors of the concentration map of less than 2mol-% without any calibration prior to the measurement. The accuracy of the reconstructed concentration maps deteriorates when the reconstruction model is biased by systematic errors such as large inhomogeneities in the static magnetic field. The presented method is a powerful tool for the fast acquisition of concentration maps that can provide valuable information for the investigation of many phenomena in chemical engineering applications. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  15. Dual Inhibition of AChE and BChE with the C-5 Substituted Derivative of Meldrum’s Acid: Synthesis, Structure Elucidation, and Molecular Docking Studies

    Directory of Open Access Journals (Sweden)

    Haroon Mehfooz

    2017-07-01

    Full Text Available Alzheimer’s disease (AD lies in the category of those diseases which are still posing challenges to medicinal chemists, and the search for super-effective drugs for the treatment of AD is a work in progress. The inhibition of cholinesterase is considered a viable strategy to enhance the level of acetylcholine in the brain. The C-5 substituted derivative of Meldrum’s acid was synthesized and screened against acetylcholinesterase (AChE and butyrylcholinesterase (BChE enzyme inhibition activity. The simple and unique structure of synthesized derivative 3 was found to be good for the dual inhibition of both enzymes (AChE and BChE. 2,2-Dimethyl-5-(([2-(trifluoromethyl phenyl]aminomethylidene-1,3-dioxane-4,6-dione (3 showed significant inhibition against AChE, with an IC50 value of 1.13 ± 0.03 µ M (Standard Neostigmine 22.2 ± 3.2 µM, and moderate inhibition against BChE, with an IC50 value of 2.12 ± 1.22 µM (Standard Neostigmine 49.6 ± 6.11 µM. The structural insights reveal that compound 3 possesses intriguing reactive groups, which can potentially evoke the non-covalent interactions and possibly assist by binding in the active site of the target protein. Docking simulations revealed that the compound 3 showed binding inside the active site gorges of both AChE and BChE. An excellent agreement was obtained, as the best docked poses showed important binding features mostly based on interactions due to oxygen atoms and the aromatic moieties of the compound. The docking computations coupled with the experimental findings ascertained that the compound 3 can serve as a scaffold for the dual inhibitors of the human acetylcholine esterases.

  16. Synthesis, characterization and in vitro studies of doxorubicin-loaded magnetic nanoparticles grafted to smart copolymers on A549 lung cancer cell line.

    Science.gov (United States)

    Akbarzadeh, Abolfazl; Samiei, Mohammad; Joo, Sang Woo; Anzaby, Maryam; Hanifehpour, Younes; Nasrabadi, Hamid Tayefi; Davaran, Soodabeh

    2012-12-18

    The aim of present study was to develop the novel methods for chemical and physical modification of superparamagnetic iron oxide nanoparticles (SPIONs) with polymers via covalent bonding entrapment. These modified SPIONs were used for encapsulation of anticancer drug doxorubicin. At first approach silane-grafted magnetic nanoparticles was prepared and used as a template for polymerization of the N-isopropylacrylamide (NIPAAm) and methacrylic acid (MAA) via radical polymerization. This temperature/pH-sensitive copolymer was used for preparation of DOX-loaded magnetic nanocomposites. At second approach Vinyltriethoxysilane-grafted magnetic nanoparticles were used as a template to polymerize PNIPAAm-MAA in 1, 4 dioxan and methylene-bis-acrylamide (BIS) was used as a cross-linking agent. Chemical composition and magnetic properties of Dox-loaded magnetic hydrogel nanocomposites were analyzed by FT-IR, XRD, and VSM. The results demonstrate the feasibility of drug encapsulation of the magnetic nanoparticles with NIPAAm-MAA copolymer via covalent bonding. The key factors for the successful prepardtion of magnetic nanocomposites were the structure of copolymer (linear or cross-linked), concentration of copolymer and concentration of drug. The influence of pH and temperature on the release profile of doxorubicin was examined. The in vitro cytotoxicity test (MTT assay) of both magnetic DOx-loaded nanoparticles was examined. The in vitro tests showed that these systems are no toxicity and are biocompatible. IC50 of DOx-loaded Fe3O4 nanoparticles on A549 lung cancer cell line showed that systems could be useful in treatment of lung cancer.

  17. Candida antartica lipase B catalyzed polycaprolactone synthesis: effects of organic media and temperature.

    Science.gov (United States)

    Kumar, A; Gross, R A

    2000-01-01

    Engineering of the reaction medium and study of an expanded range of reaction temperatures were carried out in an effort to positively influence the outcome of Novozyme-435 (immobilized Lipase B from Candida antarctica) catalyzed epsilon-CL polymerizations. A series of solvents including acetonitrile, dioxane, tetrahydrofuran, chloroform, butyl ether, isopropyl ether, isooctane, and toluene (log P from -1.1 to 4.5) were evaluated at 70 degrees C. Statistically (ANOVA), two significant regions were observed. Solvents having log P values from -1.1 to 0.49 showed low propagation rates (< or = 30% epsilon-CL conversion in 4 h) and gave products of short chain length (Mn < or = 5200 g/mol). In contrast, solvents with log P values from 1.9 to 4.5 showed enhanced propagation rates and afforded polymers of higher molecular weight (Mn = 11,500-17,000 g/mol). Toluene, a preferred solvent for this work, was studied at epsilon-CL to toluene (wt/vol) ratios from 1:1 to 10:1. The ratio 1:2 was selected since, for polymerizations at 70 degrees C, 0.3 mL of epsilon-CL and 4 h, gave high monomer conversions and Mn values (approximately 85% and approximately 17,000 g/mol, respectively). Increasing the scale of the reaction from 0.3 to 10 mL of CL resulted in a similar isolated product yield, but the Mn increased from 17,200 to 44,800 g/mol. Toluene appeared to help stabilize Novozyme-435 so that lipase-catalyzed polymerizations could be conducted effectively at 90 degrees C. For example, within only 2 h at 90 degrees C (toluene-d8 to epsilon-CL, 5:1, approximately 1% protein), the % monomer conversion reached approximately 90%. Also, the controlled character of these polymerizations as a function of reaction temperature was evaluated.

  18. Surfactant-Free RAFT Emulsion Polymerization of Styrene Using Thermoresponsive macroRAFT Agents: Towards Smart Well-Defined Block Copolymers with High Molecular Weights

    Directory of Open Access Journals (Sweden)

    Steffen Eggers

    2017-12-01

    Full Text Available The combination of reversible addition–fragmentation chain transfer (RAFT and emulsion polymerization has recently attracted much attention as a synthetic tool for high-molecular-weight block copolymers and their micellar nano-objects. Up to recently, though, the use of thermoresponsive polymers as both macroRAFT agents and latex stabilizers was impossible in aqueous media due to their hydrophobicity at the usually high polymerization temperatures. In this work, we present a straightforward surfactant-free RAFT emulsion polymerization to obtain thermoresponsive styrenic block copolymers with molecular weights of around 100 kDa and their well-defined latexes. The stability of the aqueous latexes is achieved by adding 20 vol % of the cosolvent 1,4-dioxane (DOX, increasing the phase transition temperature (PTT of the used thermoresponsive poly(N-acryloylpyrrolidine (PAPy macroRAFT agents above the polymerization temperature. Furthermore, this cosolvent approach is combined with the use of poly(N,N-dimethylacrylamide-block-poly(N-acryloylpiperidine-co-N-acryloylpyrrolidine (PDMA-b-P(APi-co-APy as the macroRAFT agent owning a short stabilizing PDMA end block and a widely adjustable PTT of the P(APi-co-APy block in between 4 and 47 °C. The temperature-induced collapse of the latter under emulsion polymerization conditions leads to the formation of RAFT nanoreactors, which allows for a very fast chain growth of the polystyrene (PS block. In dynamic light scattering (DLS, as well as cryo-transmission electron microscopy (cryoTEM, moreover, all created latexes indeed reveal a high (temperature stability and a reversible collapse of the thermoresponsive coronal block upon heating. Hence, this paper pioneers a versatile way towards amphiphilic thermoresponsive high-molecular-weight block copolymers and their nano-objects with tailored corona switchability.

  19. A Convenient Approach to Heterocyclic Building Blocks: Synthesis of Novel Ring Systems Containing a [5,6]Pyrano[2,3-c]pyrazol-4(1H-one Moiety

    Directory of Open Access Journals (Sweden)

    Wolfgang Holzer

    2007-01-01

    Full Text Available Starting from commercially available educts, a straightforward synthetic route to new heterocyclic building blocks is exemplified with the one- or two-step synthesis of tri-, tetra-, or pentacyclic ring systems. Representatives of the following novel ring systems are prepared from 3-methyl-1-phenyl-2-pyrazolin-5-one and the corresponding o-halo-arenecarbonyl chloride using calcium hydroxide in refluxing 1,4-dioxane: pyrimidino[4',5':5,6]pyrano[2,3-c]pyrazol-4(1H-one, thieno[3',2':5,6]pyrano[2,3c]pyrazol- 4-(1H-one, thieno[3',4':5,6]pyrano[2,3-c]pyrazol-4(1H-one, thieno[3'',2'':4',5']thieno[2',3':5,6]-pyrano[2,3-c]pyrazol-4(1H-one, [1,3]dioxolo[5',6'][1]benzothieno[2',3':5,6]pyrano-[2,3-c]- pyrazol-4(1H-one, pyridazino[4',3':5,6]pyrano[2,3-c]pyrazol-4(1H-one and pyrazolo-[4'',3'':5',6']pyrido[3',4':5,6]pyrano[2,3-c]pyrazol-4(1H-one. While the latter two ring systems are directly obtained due to a spontaneous intramolecular substitution reaction, in the other reactions uncyclised 4-aroylpyrazol-5-ols are produced, which are cyclised into the target heterocycles in a subsequent synthetic step (i.e. treatment with NaH in DMF. Detailed NMR spectroscopic investigations (1H-, 13C-, 15N- with the obtained compounds were undertaken to unambiguously prove the new structures.

  20. Generation of ROS mediated by mechanical waves (ultrasound) and its possible applications.

    Science.gov (United States)

    Duco, Walter; Grosso, Viviana; Zaccari, Daniel; Soltermann, Arnaldo T

    2016-10-15

    The thermal decomposition of 9,10 diphenylanthracene peroxide (DPAO 2 ) generates DPA and a mix of triplet and singlet molecular oxygen. For DPAO 2 the efficiency to produce singlet molecular oxygen is 0.35. On the other hand, it has shown that many thermal reactions can be carried out through the interaction of molecules with ultrasound. Ultrasound irradiation can create hydrodynamic stress (sonomechanical process), inertial cavitation (pyrolitic process) and long range effects mediated by radicals or ROS. Sonochemical reactions can be originated by pyrolytic like process, shock mechanical waves, thermal reactions and radical and ROS mediated reactions. Sonolysis of pure water can yield hydrogen or hydroxyl radicals and hydrogen peroxide (ROS). When DPAO 2 in 1,4 dioxane solution is treated with 20 or 24kHz and different power intensity the production of molecular singlet oxygen is observed. Specific scavengers like tetracyclone (TC) are used to demonstrate it. The efficiency now is 0.85 showing that the sonochemical process is much more efficient that the thermal one. Another endoperoxide, artemisinin was also studied. Unlike the concept of photosensitizer of photodynamic therapy, in spite of large amount of reported results in literature, the term sonosensitizer and the sonosensitization process are not well defined. We define sonosensitized reaction as one in which a chemical species decompose as consequence of cavitation phenomena producing ROS or other radicals and some other target species does undergo a chemical reaction. The concept could be reach rapidly other peroxides which are now under experimental studies. For artemisinin, an important antimalarian and anticancer drug, was established that ultrasound irradiation increases the effectiveness of the treatment but without any explanation. We show that artemisinin is an endoperoxide and behaves as a sonosensitizer in the sense of our definition. Copyright © 2016 Elsevier Inc. All rights reserved.

  1. Preparation and self-assembly behavior of polystyrene-block-poly (dimethylaminoethyl methacrylate amphiphilic block copolymer using atom transfer radical polymerization

    Directory of Open Access Journals (Sweden)

    2008-03-01

    Full Text Available Asymmetric and semi-symmetric amphiphilic diblock copolymers polystyrene-block-poly (dimethylaminoethyl methacrylate (PS-b-PDMAEMA with the same PS block length of 62 repeat units and quite short (3 repeat units or equivalent (47 repeat units length of PDMAEMA have been prepared simply by varying the ratio of the bromine-terminated macroinitiator polystyrene (PS-Br to DMAEMA using atom transfer radical polymerization (ATRP. The chemical structures and compositions of the PS-b-PDMAEMA block copolymers are studied by nuclear magnetic resonance (NMR spectroscopy, gel permeation chromatography (GPC, and elementary analysis (EA. The self-assembly behaviors of copolymers in N,N-dimethyl formamide (DMF with different pH and dioxane/water binary solvent mixture by direct dissolution method (DD, are studied by transmission electron microscopy (TEM, electron diffracting analysis (EDA, and energy-dispersive analysis of X-rays (EDAX techniques. Transmission electron microscopy results suggest that asymmetric block copolymer PS62-b-PDMAEMA3 (the numbers in the form of footnotes represent repeated units of each monomer in the copolymer can form spherical core-shell micelles, large compound reverse micelles (LCRMs, hexagonal/rhombic phases, reverse hexagonal/rhombic phases, vesicles, reverse vesicles and necklace-like reverse micelles, controlled by common or selective solvent and pH, while most of the aggregates of semi-symmetric PS62-b-PDMAEMA47 are simply spherical, such as spherical core-shell micelles and reverse spherical core-shell micelles, besides hexagonal/rhombic phases. All above structures are controlled by three components of the free energy of aggregation: core-chain stretching, interfacial energy and intercoronal chain interaction.

  2. Study of the levels of air pollution by heavy metals on an urban site of Algiers using neutron activation analysis (NAA)

    International Nuclear Information System (INIS)

    Khodja, Z.; Nedjar, A.; Azli, T.; Zergoug, Z.; Mouhouche, F.; Belamri, M.; Omari, L.; Lakhdar, C.C.

    2010-01-01

    Today, the high threshold reached by air pollution makes us become aware of the importance of the problem and the dangers which it represents for the health of the living beings and man in particular. The list of the atmospheric pollutants is long. To traditional usual but always real pollutants such as dust, SO 2 , Nox, CO, heavy metals, etc came to be added gradually to other substances such as gases for greenhouse effect: C0 2 , the CH 4 , the N 2 0, CFC, HFC, PFC and SF 6 and other substances such as ozone, the organochlorinated ones (dioxanes and furans), the HAP (Polycyclic Aromatic Hydrocarbons), etc. In Algeria, the lack of relative data to air quality makes that the impact of this form of pollution on the environment very badly known. The sources of pollution are numerous and the harmful effects are already perceived, but their direct relationship or indirect with the environmental pollution is not established. It is in this context and in continuity with work under development at the Nuclear Research Center of Algiers that we propose by this study the levels of air pollution by the fine particles and more particularly by heavy metals on the level of an urban site of Algiers with force directly exposed population density with the transmitting sources of pollution. We have used a nuclear method: neutron activation analysis technique (NAA), for the detection of traces of heavy metals in our samples of filters collected throughout one year at a rate of approximately a sample per week. One will note that this pollution varies considerably according to the components, in particular for Chromium (Cr), Iron (Fe), Mercury (Hg) and Cobalt (Co). The results were compared with other results obtained with other techniques and show a better sensitivity.

  3. PMP, a novel solute for liquid and plastic scintillation counting

    International Nuclear Information System (INIS)

    Gusten, Hans

    1983-01-01

    The excellent fluorescence properties of PMP ( 11-phenyl-3-mesityl-2-pyrazoline) such as long wavelength emission of over 400 nm, and high fluorescence quantum yield with a short decay time together with a solubility of more than one Mol/L in toluene make this compound a promising solute for scintillation counting. The Stokes' shift of PMP of over 10,000 cm -1 is twice as large as that of the commonly used PPO. Due to this unusually large Stokes' shift PMP can be used as a primary solute without requiring a secondary solute as wavelength shifter. A comparison of the scintillation properties of PMP and PPO in toluene reveals that the counting efficiency for 14 C is better for PMP while the 3 H efficiency is equally good. Due to the large Stokes' shift, PMP is about 50 percent less sensitive to color quenching than PPO. Compared to the solute combinations PPO/secondary solutes, the scintillation counting efficiency of PMP for 14 C in toluene or xylene is the same, while the absolute 3 H efficiency of PPO/secondary solutes in cocktails with emulsifiers is about 10 percent higher. The PMP scintillation efficiency for 14 C as well as 3 H in chemical quenching by urine is more or less the same as for PPO/dimethyl-POPOP. PMP is more sensitive to quenching by halogenated solvents. In the dioxane-based scintillation, this sensitivity to chemical quenching by CHCl 3 vanishes and the counting efficiencies for 14 C and 3 H are as good as for PPO/dimethyl-POPOP or PPO/bis-MSB. Due to the large Stokes' shift, the self-absorption of the scintillation light by PMP is lower than in conventional scintillators. This offers good possibilities in very large-volume applications of liquid as well as plastic scintillators

  4. Polymersomes from dual responsive block copolymers: drug encapsulation by heating and acid-triggered release.

    Science.gov (United States)

    Qiao, Zeng-Ying; Ji, Ran; Huang, Xiao-Nan; Du, Fu-Sheng; Zhang, Rui; Liang, De-Hai; Li, Zi-Chen

    2013-05-13

    A series of well-defined thermoresponsive diblock copolymers (PEO45-b-PtNEAn, n=22, 44, 63, 91, 172) were prepared by the atom transfer radical polymerization of trans-N-(2-ethoxy-1,3-dioxan-5-yl) acrylamide (tNEA) using a poly(ethylene oxide) (PEO45) macroinitiator. All copolymers are water-soluble at low temperature, but upon quickly heating to 37 °C, laser light scattering (LLS) and transmission electron microscopy (TEM) characterizations indicate that these copolymers self-assemble into aggregates with different morphologies depending on the chain length of PtNEA and the polymer concentration; the morphologies gradually evolved from spherical solid nanoparticles to a polymersome as the degree of polymerization ("n") of PtNEA block increased from 22 to 172, with the formation of clusters with rod-like structure at the intermediate PtNEA length. Both the spherical nanoparticle and the polymersome are stable at physiological pH but susceptible to the mildly acidic medium. Acid-triggered hydrolysis behaviors of the aggregates were investigated by LLS, Nile red fluorescence, TEM, and (1)H NMR spectroscopy. The results revealed that the spherical nanoparticles formed from PEO45-b-PtNEA44 dissociated faster than the polymersomes of PEO45-b-PtNEA172, and both aggregates showed an enhanced hydrolysis under acidic conditions. Both the spherical nanoparticle and polymersome are able to efficiently load the hydrophobic doxorubicin (DOX), and water-soluble fluorescein isothiocyanate-lysozyme (FITC-Lys) can be conveniently encapsulated into the polymersome without using any organic solvent. Moreover, FITC-Lys and DOX could be coloaded in the polymersome. The drugs loaded either in the polymersome or in the spherical nanoparticle could be released by acid triggering. Finally, the DOX-loaded assemblies display concentration-dependent cytotoxicity to HepG2 cells, while the copolymers themselves are nontoxic.

  5. Surface-modified functionalized polycaprolactone scaffolds for bone repair: in vitro and in vivo experiments.

    Science.gov (United States)

    Jensen, Jonas; Rölfing, Jan Hendrik Duedal; Le, Dang Quang Svend; Kristiansen, Asger Albaek; Nygaard, Jens Vinge; Hokland, Lea Bjerre; Bendtsen, Michael; Kassem, Moustapha; Lysdahl, Helle; Bünger, Cody Eric

    2014-09-01

    A porcine calvaria defect study was carried out to investigate the bone repair potential of three-dimensional (3D)-printed poly-ε-caprolactone (PCL) scaffolds embedded with nanoporous PCL. A microscopic grid network was created by rapid prototyping making a 3D-fused deposition model (FDM-PCL). Afterward, the FDM-PCL scaffolds were infused with a mixture of PCL, water, and 1,4-dioxane and underwent a thermal-induced phase separation (TIPS) followed by lyophilization. The TIPS process lead to a nanoporous structure shielded by the printed microstructure (NSP-PCL). Sixteen Landrace pigs were divided into two groups with 8 and 12 weeks follow-up, respectively. A total of six nonpenetrating holes were drilled in the calvaria of each animal. The size of the cylindrical defects was h 10 mm and Ø 10 mm. The defects were distributed randomly using following groups: (a) NSP-PCL scaffold, (b) FDM-PCL scaffold, (c) autograft, (d) empty defect, (a1) NSP-PCL scaffold + autologous mononuclear cells, and (a2) NSP-PCL scaffold + bone morphogenetic protein 2. Bone volume to total volume was analyzed using microcomputed tomography (µCT) and histomorphometry. The µCT and histological data showed significantly less bone formation in the NSP-PCL scaffolds in all three variations after both 8 and 12 weeks compared to all other groups. The positive autograft control had significantly higher new bone formation compared to all other groups except the FDM-PCL when analyzed using histomorphometry. The NSP-PCL scaffolds were heavily infiltrated with foreign body giant cells suggesting an inflammatory response and perhaps active resorption of the scaffold material. The unmodified FDM-PCL scaffold showed good osteoconductivity and osseointegration after both 8 and 12 weeks. © 2013 Wiley Periodicals, Inc.

  6. π–π-Induced aggregation and single-crystal fluorescence anisotropy of 5,6,10b-triazaacephenanthrylene

    Directory of Open Access Journals (Sweden)

    Katarzyna Ostrowska

    2018-05-01

    Full Text Available The structural origin of absorption and fluorescence anisotropy of the single crystal of the π-conjugated heterocyclic system 5,6,10b-triazaacephenanthrylene, TAAP, is presented in this study. X-ray analysis shows that the crystal framework in the space group P\\overline{1} is formed by centrosymmetric dimers of face-to-face mutually oriented TAAP molecules joined by π–π non-covalent interactions. The conformation of the TAAP molecule is stabilized by intramolecular C—H...N(sp2, N(sp2H...π(CN, and C—H...O(sp2 hydrogen bonds. The presence of weak π–π interactions is confirmed by quantum theory of atoms in molecules (QTAIM and non-covalent interaction (NCI analysis. The analysis of the optical spectra of TAAP in solution and in the solid state does not allow the specification of the aggregation type. DFT calculations for the dimer in the gas phase indicate that the lowest singlet excitation is forbidden by symmetry, suggesting H-type aggregation, even though the overall absorption spectrum is bathochromically shifted as for the J-type. The experimental determination of the permanent dipole moment of a TAAP molecule in 1,4-dioxane solution indicates the presence of the monomer form. The calculated absorption and emission spectra of the crystal in a simple approximation are consistent with the experimentally determined orientation of the absorption and emission transition dipole moments in TAAP single crystals. The electrostatic interaction between monomers with a permanent dipole moment (ca 4 D each could result in the unusual spectroscopic JH-aggregate behaviour of the TAAP dimer.

  7. The effects of waste leachates on the hydraulic conductivity of natural clays

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, F

    1989-01-01

    Sanitary land filling remains a viable alternative for disposal of the ever increasing volumes of municipal solid waste. Current landfill design practice requires the presence of a clay barrier (liner) that may consist of either a natural stratum or compacted clay borrow. The liner acts as a hydraulic barrier to control the flux of contaminants from the waste into the adjacent groundwater. In order to do this clay liners are required to have low hydraulic conductivity, k (typically 10{sup {minus}8} cm/s) that shall not increase during exposure to waste leachate. This thesis reports the assessment of compatibility between natural clays from Sarnia, Ontario, and various leachates ranging from municipal solid waste leachate to concentrated organic solvents. The studies were performed using specially designed fixed-ring permeameters that allowed controlling confining effective stresses, volume changes in the soil specimen and chemistry of the influent and effluent permeants. The Sarnia clays appeared to be compatible with domestic waste leachate, showing slight reductions in k. Extensive retardation of potassium from the leachate required long testing periods (up to twelve pore volumes) before the soils were deemed to be in chemical equilibrium. Concentrated, water-soluble organics (ethanol and dioxane) increased the hydraulic conductivity of compacted clays by 100 to 1,000-fold, thus destroying their effectiveness as liners. Water-compacted clays appeared remarkably resistant to penetration by concentrated hydrophobic solvents such as cyclohexane. Large hydraulic gradients (up to {approximately}900) were required to produce breakthrough along compaction induced fractures. However, alcohols and surfactants can facilitate the entry of hydrophobic liquids into the double layers causing large increased in k.

  8. Cooperativity of halogen, chalcogen, and pnictogen bonds in infinite molecular chains by electronic structure theory.

    Science.gov (United States)

    George, Janine; Deringer, Volker L; Dronskowski, Richard

    2014-05-01

    Halogen bonds (XBs) are intriguing noncovalent interactions that are frequently being exploited for crystal engineering. Recently, similar bonding mechanisms have been proposed for adjacent main-group elements, and noncovalent "chalcogen bonds" and "pnictogen bonds" have been identified in crystal structures. A fundamental question, largely unresolved thus far, is how XBs and related contacts interact with each other in crystals; similar to hydrogen bonding, one might expect "cooperativity" (bonds amplifying each other), but evidence has been sparse. Here, we explore the crucial step from gas-phase oligomers to truly infinite chains by means of quantum chemical computations. A periodic density functional theory (DFT) framework allows us to address polymeric chains of molecules avoiding the dreaded "cluster effects" as well as the arbitrariness of defining a "large enough" cluster. We focus on three types of molecular chains that we cut from crystal structures; furthermore, we explore reasonable substitutional variants in silico. We find evidence of cooperativity in chains of halogen cyanides and also in similar chalcogen- and pnictogen-bonded systems; the bonds, in the most extreme cases, are amplified through cooperative effects by 79% (I···N), 90% (Te···N), and 103% (Sb···N). Two experimentally known organic crystals, albeit with similar atomic connectivity and XB characteristics, show signs of cooperativity in one case but not in another. Finally, no cooperativity is observed in alternating halogen/acetone and halogen/1,4-dioxane chains; in fact, these XBs weaken each other by up to 26% compared to the respective gas-phase dimers.

  9. Antioxidant Activity of Flaxseed Extracts in Lipid Systems

    Directory of Open Access Journals (Sweden)

    Adriana Slavova-Kazakova

    2015-12-01

    Full Text Available The aim of this work was to compare the antioxidant activity of the extract of flaxseed and its alkaline hydrolysate in two model systems: lipid autoxidation of triacylglycerols of sunflower oil (TGSO—in a homogeneous lipid media and during β-carotene-linoleate emulsion system. In addition, pure lignans were tested. The material was defatted with hexane and then phenolic compounds were extracted using dioxane-ethanol (50:50, v/v mixture. Carbohydrates were removed from the crude extract using an Amberlite XAD-16 column chromatography. The content of total phenolic compounds in the crude extract and after alkaline hydrolysis was determined using a Folin-Ciocalteu’s phenol reagent. Individual phenolic compounds were determined by nordihydroguaiaretic acid (RP-HPLC method in gradient system. The alkaline hydrolysis increased the content of total phenolics in the extract approximately by 10%. In the extracts of flaxseed, phenolic compounds were present in the form of macromolecular complex. In the alkaline hydrolysate, secoisolariciresinol diglucoside (SDG was found as the main phenolic compound. Small amounts of p-coumaric and ferulic acids were also determined. SDG and both extracts were not able to inhibit effectively lipid autoxidation. The kinetics of TGSO autoxidation at 80 °C in absence and in presence of the extract before hydrolysis (EBH and after hydrolysis (EAH was monitored and compared with known standard antioxidants. Ferulic acid (FA and butylated hydroxyl toluene (BHT showed much higher antioxidant efficiency and reactivity than that of both extracts. Secoisolariciresinol (SECO showed a higher activity in both model systems than SDG. However, the activity of SECO was much lower than that of nordihydroquaiaretic acid (NDGA.

  10. A novel nano-structured porous polycaprolactone scaffold improves hyaline cartilage repair in a rabbit model compared to a collagen type I/III scaffold: in vitro and in vivo studies.

    Science.gov (United States)

    Christensen, Bjørn Borsøe; Foldager, Casper Bindzus; Hansen, Ole Møller; Kristiansen, Asger Albæk; Le, Dang Quang Svend; Nielsen, Agnete Desirée; Nygaard, Jens Vinge; Bünger, Cody Erik; Lind, Martin

    2012-06-01

    To develop a nano-structured porous polycaprolactone (NSP-PCL) scaffold and compare the articular cartilage repair potential with that of a commercially available collagen type I/III (Chondro-Gide) scaffold. By combining rapid prototyping and thermally induced phase separation, the NSP-PCL scaffold was produced for matrix-assisted autologous chondrocyte implantation. Lyophilizing a water-dioxane-PCL solution created micro and nano-pores. In vitro: The scaffolds were seeded with rabbit chondrocytes and cultured in hypoxia for 6 days. qRT-PCR was performed using primers for sox9, aggrecan, collagen type 1 and 2. In vivo: 15 New Zealand White Rabbits received bilateral osteochondral defects in the femoral intercondylar grooves. Autologous chondrocytes were harvested 4 weeks prior to surgery. There were 3 treatment groups: (1) NSP-PCL scaffold without cells. (2) The Chondro-Gide scaffold with autologous chondrocytes and (3) NSP-PCL scaffold with autologous chondrocytes. Observation period was 13 weeks. Histological evaluation was made using the O'Driscoll score. In vitro: The expressions of sox9 and aggrecan were higher in the NSP-PCL scaffold, while expression of collagen 1 was lower compared to the Chondro-Gide scaffold. In vivo: Both NSP-PCL scaffolds with and without cells scored significantly higher than the Chondro-Gide scaffold when looking at the structural integrity and the surface regularity of the repair tissue. No differences were found between the NSP-PCL scaffold with and without cells. The NSP-PCL scaffold demonstrated higher in vitro expression of chondrogenic markers and had higher in vivo histological scores compared to the Chondro-Gide scaffold. The improved chondrocytic differentiation can potentially produce more hyaline cartilage during clinical cartilage repair. It appears to be a suitable cell-free implant for hyaline cartilage repair and could provide a less costly and more effective treatment option than the Chondro-Gide scaffold with cells.

  11. Intramolecular, Exciplex-Mediated, Proton-Coupled, Charge-Transfer Processes in N,N-Dimethyl-3-(1-pyrenyl)propan-1-ammonium Cations: Influence of Anion, Solvent Polarity, and Temperature.

    Science.gov (United States)

    Safko, Trevor M; Faleiros, Marcelo M; Atvars, Teresa D Z; Weiss, Richard G

    2016-06-16

    An intramolecular exciplex-mediated, proton-coupled, charge-transfer (PCCT) process has been investigated for a series of N,N-dimethyl-3-(1-pyrenyl)propan-1-ammonium cations with different anions (PyS) in solvents of low to intermediate polarity over a wide temperature range. Solvent mediates both the equilibrium between conformations of the cation that place the pyrenyl and ammonium groups in proximity (conformation C) or far from each other (conformation O) and the ability of the ammonium group to transfer a proton adiabatically in the PyS excited singlet state. Thus, exciplex emission, concurrent with the PCCT process, was observed only in hydrogen-bond accepting solvents of relatively low polarity (tetrahydrofuran, ethyl acetate, and 1,4-dioxane) and not in dichloromethane. From the exciplex emission and other spectroscopic and thermodynamic data, the acidity of the ammonium group in conformation C of the excited singlet state of PyS (pKa*) has been estimated to be ca. -3.4 in tetrahydrofuran. The ratios between the intensities of emission from the exciplex and the locally excited state (IEx/ILE) appear to be much more dependent on the nature of the anion than are the rates of exciplex formation and decay, although the excited state data do not provide a quantitative measure of the anion effect on the C-O equilibrium. The activation energies associated with exciplex formation in THF are calculated to be 0.08 to 0.15 eV lower than for the neutral amine, N,N-dimethyl-3-(1-pyrenyl)propan-1-amine. Decay of the exciplexes formed from the deprotonation of PyS is hypothesized to occur through charge-recombination processes. To our knowledge, this is the first example in which photoacidity and intramolecular exciplex formation (i.e., a PCCT reaction) are coupled.

  12. Computational Elucidation of a Role That Brønsted Acidification of the Lewis Acid-Bound Water Might Play in the Hydrogenation of Carbonyl Compounds with H2 in Lewis Basic Solvents.

    Science.gov (United States)

    Heshmat, Mojgan; Privalov, Timofei

    2017-08-25

    Brønsted acidification of water by Lewis acid (LA) complexation is one of the fundamental principles in chemistry. Using transition-state calculations (TS), herein we investigate the role that Brønsted acidification of the LA-bound water might play in the mechanism of the hydrogenation of carbonyl compounds in Lewis basic solvents under non-anhydrous conditions. The potential energy scans and TS calculations were carried out with a series of eight borane LAs as well as the commonly known strong LA AlCl 3 in 1,4-dioxane or THF as Lewis basic solvents. Our molecular model consists of the dative LA-water adduct with hydrogen bonds to acetone and a solvent molecule plus one additional solvent molecule that participates is the TS structure describing the cleavage of H 2 at acetone's carbonyl carbon atom. In all the molecular models applied here, acetone (O=CMe 2 ) is the archetypical carbonyl substrate. We demonstrate that Brønsted acidification of the LA-bound water can indeed lower the barrier height of the solvent-involving H 2 -cleavage at the acetone's carbonyl carbon atom. This is significant because at present it is believed that the mechanism of the herein considered reaction is described by the same mechanism regardless of whether the reaction conditions are strictly anhydrous or non-anhydrous. Our results offer an alternative to this belief that warrants consideration and further study. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Quinolinone and pyridopyrimidinone inhibitors of DNA-dependent protein kinase.

    Science.gov (United States)

    Barbeau, Olivier R; Cano-Soumillac, Celine; Griffin, Roger J; Hardcastle, Ian R; Smith, Graeme C M; Richardson, Caroline; Clegg, William; Harrington, Ross W; Golding, Bernard T

    2007-08-21

    8-Substituted 2-morpholin-4-yl-quinolin-4-ones and 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones with selected aryl and heteroaryl groups as the substituent have been synthesised as potential inhibitors of DNA-dependent protein kinase. A multiple-parallel approach, employing Suzuki cross-coupling methodology, was utilised in the preparation of 8-substituted 2-morpholin-4-yl-quinolin-4-ones. For this purpose 8-bromo-2-morpholin-4-yl-quinolin-4-one was required as an intermediate. This compound was obtained by adapting a literature route in which thermal cyclocondensation of (2-bromoanilino)-morpholin-4-yl-5-methylene-2,2-dimethyl[1,3]dioxane-4,6-dione afforded 8-bromo-2-morpholin-4-yl-quinolin-4-one. A multiple-parallel approach, employing Suzuki cross-coupling methodology, was also utilised to prepare 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones using 9-hydroxy-2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-one O-trifluoromethanesulfonate as an intermediate. 8-Substituted 2-morpholin-4-yl-quinolin-4-ones and 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones were both inhibitors of DNA-dependent protein kinase. When the substituent was dibenzothiophen-4-yl, dibenzofuran-4-yl or biphen-3-yl, IC50 values in the low nanomolar range were observed. Interestingly, the pyridopyrimidinones and quinolinones were essentially equipotent with the corresponding 8-substituted 2-morpholin-4-yl-chromen-4-ones previously reported (I. R. Hardcastle, X. Cockcroft, N. J. Curtin, M. Desage El-Murr, J. J. J. Leahy, M. Stockley, B. T. Golding, L. Rigoreau, C. Richardson, G. C. M. Smith and R. J. Griffin, J. Med. Chem., 2005, 48, 7829-7846).

  14. Surface biofunctionalization of three-dimensional porous poly(lactic acid) scaffold using chitosan/OGP coating for bone tissue engineering.

    Science.gov (United States)

    Zeng, Sen; Ye, Jianhua; Cui, Zhixiang; Si, Junhui; Wang, Qianting; Wang, Xiaofeng; Peng, Kaiping; Chen, Wenzhe

    2017-08-01

    As one of the stimulators on bone formation, osteogenic growth peptide (OGP) improves both proliferation and differentiation of the bone cells in vitro and in vivo. The aim of this work was the preparation of three dimensional porous poly(lactic acid) (PLA) scaffold with high porosity from PLA-dioxane-water ternary system with the use of vacuum-assisted solvent casting, phase separation, solvent extraction and particle leaching methods. Then, by surface coating of PLA scaffold with chitosan (CS)/OGP solution, biofunctionalization of PLA scaffold had been completed for application in bone regeneration. The effects of frozen temperature (-20, -50, -80°C) and PLA solution concentration (10, 12, 14wt%) on the microstructure, water absorption, porosity, hydrophilicity, mechanical properties, and biocompatibility of PLA and CS/OGP/PLA scaffold were investigated. Results showed that both PLA and CS/OGP/PLA scaffolds have an interconnected network structure and a porosity of up to 96.1% and 91.5%, respectively. The CS/OGP/PLA scaffold exhibited better hydrophilicity and mechanical properties than that of uncoated PLA scaffold. Moreover, the results of cell culture test showed that CS/OGP coating could stimulate the proliferation and growth of osteoblast cells on CS/OGP/PLA scaffold. These finding suggested that the surface biofunctionalization by CS/OGP coating layer could be an effective method on enhancing cell adhesion to synthetic polymer-based scaffolds in tissue engineering application and the developed porous CS/OGP/PLA scaffold should be considered as alternative biomaterials for bone regeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Synthesis, DFT band structure calculations, optical and photoelectrical characterizations of the novel 5-hydroxy-4-methoxy-7-oxo-7H-furo[3,2-g]chromene-6-carbonitrile (HMOFCC)

    Science.gov (United States)

    Ibrahim, Magdy A.; Halim, Shimaa Abdel; Roushdy, N.; Farag, A. A. M.; El-Gohary, Nasser M.

    2017-11-01

    Reaction of 4-methoxy-5-oxo-5H-furo[3,2-g]chromene-6-carboxaldehyde (1) with hydroxylamine hydrochloride resulted in ring transformation producing the novel 5-hydroxy-4-methoxy-7-oxo-7H-furo[3,2-g]chromene-6-carbonitrile (HMOFCC). The structure was deduced based on its correct elemental analysis and spectral data (IR, 1H NMR, 13C NMR and mass spectra). The geometries of the HMOFCC were completely optimized by means of DFT-B3LYP/6-311++G (d,p) theoretical level. The ground state properties such as; total energy, the energy of HOMO and LUMO and Mulliken atomic charges were also determined. In addition, the two solvents; polar (methanol) and nonpolar (dioxane) were utilized to extract the electronic absorption spectra. The assignment of the detected bands was discussed by TD-DFT calculations. A cauliflower-like, as well as, needle-like leaves morphologies were observed using scanning electron microscope images. Two direct optical band gaps were extracted from the photon energy dependence of absorption coefficient at the band edges and found to be 1.16 and 2.56 eV. A characteristic emission peak of photoluminescence spectrum was observed and shifted depending on the solvent type. A remarkable rectification characteristic of HMOFCC/p-Si heterojunction confirms the diode-like behavior. The main important parameters like series resistance, shunt resistance and reverse saturation current show illumination dependence under influence of the illumination intensity range 20-100 mW/cm2. The heterojunction based HMOFCC showed phototransient properties under various illumination intensities which give the recommendation for the studied heterojunction in the field of optoelectronic device application.

  16. Modulation of physical and biological properties of a composite PLLA and polyaspartamide derivative obtained via thermally induced phase separation (TIPS) technique

    Energy Technology Data Exchange (ETDEWEB)

    Carfì Pavia, Francesco [Department of Civil, Environmental, Aerospace, Materials Engineering, University of Palermo, 90142 Palermo (Italy); Palumbo, Fabio Salvatore, E-mail: fabiosalvatore.palumbo@unipa.it [Dipartimento di Scienze e Tecnologie Biologiche Chimiche e Farmaceutiche, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123 Palermo (Italy); La Carrubba, Vincenzo [Department of Civil, Environmental, Aerospace, Materials Engineering, University of Palermo, 90142 Palermo (Italy); Istituto Euro Mediterraneo di Scienza e Tecnologia (IEMEST) Via Michele Miraglia, 20 - 90139, Palermo (Italy); Bongiovì, Flavia [Dipartimento di Scienze e Tecnologie Biologiche Chimiche e Farmaceutiche, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123 Palermo (Italy); Brucato, Valerio [Department of Civil, Environmental, Aerospace, Materials Engineering, University of Palermo, 90142 Palermo (Italy); Pitarresi, Giovanna; Giammona, Gaetano [Dipartimento di Scienze e Tecnologie Biologiche Chimiche e Farmaceutiche, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123 Palermo (Italy)

    2016-10-01

    In the present study, blend of poly L-lactic acid (PLLA) with a graft copolymer based on α,β-poly(N-hydroxyethyl)-DL-aspartamide and PLA named PHEA-PLA, has been used to design porous scaffold by using Thermally Induced Phase Separation (TIPS) technique. Starting from a homogeneous ternary solution of polymers, dioxane and deionised water, PLLA/PHEA-PLA porous foams have been produced by varying the polymers concentration and de-mixing temperature in metastable region. Results have shown that scaffolds prepared with a polymer concentration of 4% and de-mixing temperature of 22.5 °C are the best among those assessed, due to their optimal pore size and interconnection. SEM and DSC analysis have been carried out respectively to study scaffold morphology and the influence of PHEA-PLA on PLLA crystallization, while DMF extraction has been carried out in order to quantify PHEA-PLA into the final scaffolds. To evaluate scaffold biodegradability, a hydrolysis study has been performed until 56 days by incubating systems in a media mimicking physiological environment (pH 7.4). Results obtained have highlighted a progressive increase in weight loss with time in PLLA/PHEA-PLA scaffolds, conceivably due to the presence of PHEA-PLA and polymers interpenetration. Viability and adhesion of bovine chondrocytes seeded on the scaffolds have been studied by MTS test and SEM analysis. From results achieved it appears that the presence of PHEA-PLA increases cells affinity, allowing a faster adhesion and proliferation inside the scaffold. - Highlights: • Blended scaffolds of PLLA and PHEA-PLA were successfully obtained with TIPS technique. • Scaffolds with an open porosity and a good interconnection were formed. • PHEA-PLA improved water affinity accelerating rate of hydrolysis of blended scaffold. • Preliminary assay suggests that PHEA-PLA improved chondrocytes uptake and viability.

  17. Development and validation of a stability-indicating RP-HPLC method for assay of betamethasone and estimation of its related compounds.

    Science.gov (United States)

    Fu, Qiang; Shou, Minshan; Chien, Dwight; Markovich, Robert; Rustum, Abu M

    2010-02-05

    Betamethasone (9alpha-fluoro-16beta-methylprednisolone) is one of the members of the corticosteriod family of active pharmaceutical ingredient (API), which is widely used as an anti-inflammatory agent and also as a starting material to manufacture various esters of betamethasone. A stability-indicating reverse-phase high performance liquid chromatography (RP-HPLC) method has been developed and validated which can separate and accurately quantitate low levels of 26 betamethasone related compounds. The stability-indicating capability of the method was demonstrated through adequate separation of all potential betamethasone related compounds from betamethasone and also from each other that are present in aged and stress degraded betamethasone stability samples. Chromatographic separation of betamethasone and its related compounds was achieved by using a gradient elution at a flow rate of 1.0mL/min on a ACE 3 C18 column (150mmx4.6mm, 3microm particle size, 100A pore size) at 40 degrees C. Mobile phase A of the gradient was 0.1% methanesulfonic acid in aqueous solution and mobile phase B was a mixture of tert-butanol and 1,4-dioxane (7:93, v/v). UV detection at 254nm was employed to monitor the analytes. For betamethasone 21-aldehyde, the QL and DL were 0.02% and 0.01% respectively. For betamethasone and the rest of the betamethasone related compounds, the QL and DL were 0.05% and 0.02%. The precision of betamethasone assay is 0.6% and the accuracy of betamethasone assay ranged from 98.1% to 99.9%.

  18. Modulation of physical and biological properties of a composite PLLA and polyaspartamide derivative obtained via thermally induced phase separation (TIPS) technique

    International Nuclear Information System (INIS)

    Carfì Pavia, Francesco; Palumbo, Fabio Salvatore; La Carrubba, Vincenzo; Bongiovì, Flavia; Brucato, Valerio; Pitarresi, Giovanna; Giammona, Gaetano

    2016-01-01

    In the present study, blend of poly L-lactic acid (PLLA) with a graft copolymer based on α,β-poly(N-hydroxyethyl)-DL-aspartamide and PLA named PHEA-PLA, has been used to design porous scaffold by using Thermally Induced Phase Separation (TIPS) technique. Starting from a homogeneous ternary solution of polymers, dioxane and deionised water, PLLA/PHEA-PLA porous foams have been produced by varying the polymers concentration and de-mixing temperature in metastable region. Results have shown that scaffolds prepared with a polymer concentration of 4% and de-mixing temperature of 22.5 °C are the best among those assessed, due to their optimal pore size and interconnection. SEM and DSC analysis have been carried out respectively to study scaffold morphology and the influence of PHEA-PLA on PLLA crystallization, while DMF extraction has been carried out in order to quantify PHEA-PLA into the final scaffolds. To evaluate scaffold biodegradability, a hydrolysis study has been performed until 56 days by incubating systems in a media mimicking physiological environment (pH 7.4). Results obtained have highlighted a progressive increase in weight loss with time in PLLA/PHEA-PLA scaffolds, conceivably due to the presence of PHEA-PLA and polymers interpenetration. Viability and adhesion of bovine chondrocytes seeded on the scaffolds have been studied by MTS test and SEM analysis. From results achieved it appears that the presence of PHEA-PLA increases cells affinity, allowing a faster adhesion and proliferation inside the scaffold. - Highlights: • Blended scaffolds of PLLA and PHEA-PLA were successfully obtained with TIPS technique. • Scaffolds with an open porosity and a good interconnection were formed. • PHEA-PLA improved water affinity accelerating rate of hydrolysis of blended scaffold. • Preliminary assay suggests that PHEA-PLA improved chondrocytes uptake and viability.

  19. Synthesis and investigation of the physicochemical properties of 2-(5-((theophylline-7'-ylmethyl-4-phenyl-4H-1,2,4-triazole-3-ylthio-acetic acid salts

    Directory of Open Access Journals (Sweden)

    A. S. Gotsulya

    2014-02-01

    spectrometer “Mercury 400” (solvent - DMSO-d6 or DMSO-d6 + CCl4, the internal standard - tetramethylsilane. Chromatography-mass spectral researches were performed on the instrument Agilent 1100 Series LC/MSD System, method of ionization - chemical ionization at the atmospheric pressure (APCI. Propyl ester of the theophylline-7-acetic acid. To the 0,055 mol of sodium hydrogencarbonate in 150 ml of DMF adds 0,05 mole of the theophylline and heated with stirring 5 - 10 minutes. To the reaction compound adds 0,055 mole of the monochloracetate acid propyl ester and boil with constant stirring 5 - 6 hours. After cooling to the reaction mixture with stirring, adds an equal volume of water. The precipitate dissolves, then falles again. Ester precipitate is filtered, washed with water, then with a small amount of methanol and dried. White crystalline solid, insoluble in water, soluble in organic solvents (alcohols, dioxane, DMF, DMSO. For the analysis is purified from 1-propanol. Yield 82%. Hydrazide of the theophylline -7-acetic acid. To the heated 0,03 mole solution of the propyl ester theophylline -7- acetic acid in 200 ml of ethanol adds 0.3 mole of hydrazine hydrate. Reactionary compound leave at room temperature for 12 hours. Hydrazide precipitate is filtered, washed with water, acetone and dried. Output 79%. White, amorphous substance, insoluble in water, acetone, soluble in alcohols, dioxane, soluble in DMF, DMSO. Crystallized from a mixture DMF-water (1:1. Tm. = 210-211 ºC. 2-(2-(theophylline-7'-ylacetyl-N-phenylhydrazinecarbothioamide. 0,05 mol of phenylisothiocyanate, 130 ml of dioxane and 90 ml of water heated up to boiling for 1 hour, cooled, add 100 ml of water, the precipitate is filtered, washed with water, 2-propanol and crystallized from a mixture water- dioxane, dimethylformamide. Output - 71 %. Tm . = 262-265 ºC. 7-((5-mercapto-4-phenyl-4H-1,2,4-triazoles-3-ylmethyltheophylline. 0,01 mol of compound 2 -(2-(theophyllineacetyl-N-phenylhydrazyncarbothio-amide, 0

  20. α-Tocopherol-5-Me-T. Synthesis, purification and characterization

    International Nuclear Information System (INIS)

    Corol-Cucu, Delia-Irina; Chiper, Diana; Mihaila, V.; Negoita, N.

    2000-01-01

    The E vitamine is named 'vitamine of antisterility' because it is essential for good functioning of genital organs. It is involved in cellular oxidation processes, in muscle creatinine metabolism and metabolism of saccharides encouraging glycogen deposition in tissues. The name of E vitamine is given to eight different compounds which have a ring with methyl and hydroxyl groups. Four of them, named tocopherols, contain a lateral saturated chain which derives from fitol and the others, named tocotrienols, have three double bonds in the lateral chain.This paper refers to synthesis, purification and characterization of α-tocopherol labelled with tritium in 5-methyl position. Tritium is different by the other hydrogen isotopes because it is the only radioactive isotope of hydrogen. The α-tocopherol-5-Me-T. The dry HCl is bubbled in a mixture of γ-tocopherol, paraformaldehyde and ZnCl 2 powder in dry Et 2 O. This solution remains at a standstill for a few hours and after that water is slowly added under stirring at low temperature ( 2 SO 4 . The next step is filtration and evaporation of ether stratum under nitrogen environment. One obtains 5-Cl-Me-α-tocopherol. For synthesis of α-tocopherol-5-Me-T the replacement of chlorine with tritium is done through catalytic dechlorination with Pd/C or Pd/CaCO 3 (10% Pd) as catalysts. One half of 5-Me-Cl compound is solved in dioxane and then the catalyst and deuterium are added under stirring, for 2 hours at room temperature. After filtration and washing with MeOH, the solvent is eliminated under vacuum conditions. Thus one obtains α-tocopherol-5-Me-T. The purification has been carried out through thin layer chromatography with C 6 H 6 as solvent (Al 2 O 3 as support) or solvent system C 6 H 6 : CH 3 OH (98:2, v/v) (silicagel as support). The determination of activity is carried out with LSC (Liquid Scintillation Counter). A 98% purity was determined through TLC in the same conditions while determination of activity

  1. Ex situ generation of stoichiometric HCN and its application in the Pd-catalysed cyanation of aryl bromides: evidence for a transmetallation step between two oxidative addition Pd-complexes.

    Science.gov (United States)

    Kristensen, Steffan K; Eikeland, Espen Z; Taarning, Esben; Lindhardt, Anders T; Skrydstrup, Troels

    2017-12-01

    A protocol for the Pd-catalysed cyanation of aryl bromides using near stoichiometric and gaseous hydrogen cyanide is reported for the first time. A two-chamber reactor was adopted for the safe liberation of ex situ generated HCN in a closed environment, which proved highly efficient in the Ni-catalysed hydrocyanation as the test reaction. Subsequently, this setup was exploited for converting a range of aryl and heteroaryl bromides (28 examples) directly into the corresponding benzonitriles in high yields, without the need for cyanide salts. Cyanation was achieved employing the Pd(0) precatalyst, P( t Bu) 3 -Pd-G3 and a weak base, potassium acetate, in a dioxane-water solvent mixture. The methodology was also suitable for the synthesis of 13 C-labelled benzonitriles with ex situ generated 13 C-hydrogen cyanide. Stoichiometric studies with the metal complexes were undertaken to delineate the mechanism for this catalytic transformation. Treatment of Pd(P( t Bu) 3 ) 2 with H 13 CN in THF provided two Pd-hydride complexes, (P( t Bu) 3 ) 2 Pd(H)( 13 CN), and [(P( t Bu) 3 )Pd(H)] 2 Pd( 13 CN) 4 , both of which were isolated and characterised by NMR spectroscopy and X-ray crystal structure analysis. When the same reaction was performed in a THF : water mixture in the presence of KOAc, only (P( t Bu) 3 ) 2 Pd(H)( 13 CN) was formed. Subjection of this cyano hydride metal complex with the oxidative addition complex (P( t Bu) 3 )Pd(Ph)(Br) in a 1 : 1 ratio in THF led to a transmetallation step with the formation of (P( t Bu) 3 ) 2 Pd(H)(Br) and 13 C-benzonitrile from a reductive elimination step. These experiments suggest the possibility of a catalytic cycle involving initially the formation of two Pd(ii)-species from the oxidative addition of L n Pd(0) into HCN and an aryl bromide followed by a transmetallation step to L n Pd(Ar)(CN) and L n Pd(H)(Br), which both reductively eliminate, the latter in the presence of KOAc, to generate the benzonitrile and L n Pd(0).

  2. Forest Irrigation of Tritiated Water: A Proven Tritiated Water Management Tool - 13357

    Energy Technology Data Exchange (ETDEWEB)

    Prater, Phil; Blount, Gerald; Kmetz, Thomas; Vangelas, Karen [Savannah River National Laboratory, Bldg. 773-42A, Aiken, SC 29808 (United States)

    2013-07-01

    Tritium releases from the Old Radioactive Waste Burial Ground (ORWBG) at the SRS in South Carolina has impacted groundwater and surface water. Tritiated groundwater plumes discharge into Fourmile Branch which is a small tributary of the Savannah River, a regional water resource. Taking advantage of the groundwater flow paths and the local topography a water collection and irrigation system was constructed and has been used at the SRS for over a decade to reduce these tritiated water releases to Fourmile Branch. The tritiated water is transferred to the atmosphere by evaporation from the pond surface, and after irrigation, wetted surface evaporation and evapotranspiration through the forest vegetation. Over the last decade SRS has irrigated over 120,000,000 gallons of tritiated water, which diverted over 6000 curies away from Fourmile Branch and the Savannah River. The system has been effective in reducing the flux of tritiated groundwater by approximately 70%. Mass balance studies of tritium in the forest soils before operations and over the last decade indicate that approximately 90% of the tritiated water that is irrigated is transferred to the atmosphere. Dose studies indicate that exposure to site workers and offsite maximally exposed individual is very low, approximately 6 mrem/year and 0.004 mrem/year, respectively. To consistently meet the flux reduction goal of tritium into Fourmile Branch optimization activities are proposed. These efforts will increase irrigation capacity and area. An additional 17 acres are proposed for an expansion of the area to be irrigated and a planting of approximately 40 acres of pine forest plantations is underway to expand irrigation capacity. Co-mingled with the tritiated groundwater are low concentrations of chlorinated volatile organic compounds (cVOCs), and 1,4-dioxane. Research studies and SRS field data indicate the forest irrigation system may have an added benefit of reducing the mass of these co-contaminants via

  3. Reduction of VOC emission from natural flours filled biodegradable bio-composites for automobile interior.

    Science.gov (United States)

    Kim, Ki-Wook; Lee, Byoung-Ho; Kim, Sumin; Kim, Hyun-Joong; Yun, Ju-Ho; Yoo, Seung-Eul; Sohn, Jong Ryeul

    2011-03-15

    Various experiments, such as the thermal extract (TE) method, field and emission cell (FLEC) method and 20 L small chamber, were performed to examine the total volatile organic compound (TVOC) emissions from bio-composites. The TVOC of neat poly(lactic acid) (PLA) was ranged from 0.26 mg/m(2)h to 4.11 mg/m(2)h with increasing temperature. For both PLA bio-composites with pineapple flour and destarched cassava flour, the temperature increased from 0.30 mg/m(2)h to 3.72 mg/m(2)h and from 0.19 mg/m(2)h to 8.74 mg/m(2)h, respectively. The TVOC emission factors of all samples increased gradually with increasing temperature. Above 70°C, both PLA-P and PLA-C composites had higher TVOC emission factors than neat PLA due to the rapid emission of natural volatile organic compounds (VOCs), such as furfural (2-furancarboxyaldehyde). PLA composites containing 30 wt% flour had high 1,4-dioxane reduction ability, >50%. The TVOC of poly(butylene succinate) (PBS) was emitted rapidly from 50 °C to 90 °C due to succinic acid from the pyrolysis of PBS. The TVOC emission factors of PLA bio-composite and PBS bio-composites were reduced using the bake-out method (temperature at 70 °C and baking time 5h). The initial TVOC emission factors of the PLA and PBS bio-composites with pineapple flour and destarched cassava flour were reduced by the baking treatment using FLEC. The TVOC factors from PLA and PBS decreased until 5 days and were commonly maintained a relatively constant value after 5 days using 20L small chamber. The decrease in TVOC emission showed a similar trend to that of the TE and FLEC method. This method confirmed the beneficial effect of the baking treatment effect for polypropylene and linear density polyethylene (LDPE). Copyright © 2010 Elsevier B.V. All rights reserved.

  4. Studies on /sup 13/C-NMR spectroscopy of carbohydrates. Application of selective deuteration

    Energy Technology Data Exchange (ETDEWEB)

    Mizutani, Kenji; Kajita, Hitomi; Tashima, Takako; Tanaka, Osamu (Hiroshima Univ. (Japan). School of Medicine)

    1982-10-01

    Recently, Stuart et al. have reported that on heating with deuterated Raney nickel in D/sub 2/O, hexopyranosides and oligosaccharides were deuterated selectively at carbon atoms bound to a free hydroxyl group. For the application of this procedure to chemistry and biochemistry of more complex carbohydrates, further study on this reaction was conducted. On prolonged treatment with Raney nickel (24h), methyl ..cap alpha..-L-arabinopyranoside (4) and ..beta..-D-xylopyranoside (5) were partially epimerized to give (5) and methyl ..cap alpha..-L-lyxopyranoside (6) from (4), and methyl ..beta..-D-ribopyranoside (7) and (4) from (5), respectively. Methyl ..cap alpha..-L-rhamnopyranoside (8) was epimerized more slowly to yield methyl 6-deoxy-..cap alpha..-L-glucopyranoside (9). The best conditions for the deuteration under minimizing the epimerization was refluxing with W-7 type deuterated Raney nickel in D/sub 2/O-dioxane (1 : 1) or methanol-d/sub 4/-D/sub 2/O (1 : 1) for about 9h. Methyl ..beta..-sophoroside (13), methyl ..beta..-cellobioside (23) and ..beta..-sophorosyl and ..beta..-gentiobiosyl units of ginsenoside-Rb/sub 1/ (24), a Ginseng-saponin, were deuterated as expected under these conditions, while C-2 and 4 of the inner ..beta..-glucopyranosyl moiety of methyl ..beta..-laminaribioside (18) and C-4 of the inner ..beta..-glucopyranosyl moiety of methyl 2,3-di-O-..beta..-D-glucopyranosyl-..beta..-D-glucopyranoside (22) remained almost undeuterated. Deuteration of ..cap alpha..-1,6-glucan (25) proceeded rather slowly than those of mono- and oligosaccharide to obtain the expected deuteration after treatment for 24h. In the case of the deuteration of cis- and dl-trans-1, 2-cyclohexanediols (11) and ( (12), both deuteration and epimerization proceeded very fast to give an equilibrated mixture of (11-d/sub 2/) and (12-d/sub 2/) within 9h, while the isolated carbinyl carbon (C-12) of (24) was not deuterated. Further, by means of the above selective deuteration, /sup 13

  5. Quantitative evaluation of inhibitory effect of various substances on anaerobic ammonia oxidation (anammox).

    Science.gov (United States)

    Nakamura, Tomotaka; Harigaya, Yuhki; Kimura, Yuya; Kuroiwa, Megumi; Kurata, Yuhri; Isaka, Kazuichi; Suwa, Yuichi

    2017-09-01

    The inhibitory effect of 20 substances of various chemical species on the anaerobic ammonia oxidation (anammox) activity of an enrichment culture, predominated by Candidatus Brocadia, was determined systematically by using a 15 N tracer technique. The initial anammox rate was determined during first 25 min with a small-scale anaerobic batch incubation supplemented with possible inhibitors. Although Cu 2+ and Mn 2+ did not inhibit anammox, the remaining 18 substances [Ni 2+ , Zn 2+ , Co 2+ , [Formula: see text] , Fe 2+ , 4 amines, ethylenediaminetetraacetic acid (EDTA), ethylenediamine-N,N'-bis (2-hydroxyphenylacetic acid) (EDDHA), citric acid, nitrilotriacetic acid (NTA), N,N-dimethylacetamide (DMA), 1,4-dioxane, dimethyl sulfoxide (DMSO), N,N-dimethylformamide (DMF) and tetrahydrofuran (THF)] were inhibitory. Inhibitory effect of NTA, EDDHA, THF, DMF, DMA and amines on anammox was first determined in this study. Inhibitory effects of metals were re-evaluated because chelators, which may interfere inhibitory effect, have been used to dissolve metal salts into assay solution. The relative anammox activities as a function of concentration of each substance were described successfully (R 2  > 0.91) either with a linear inhibition model or with a Michaelis-Menten-based inhibition model. IC 50 values were estimated based on either model, and were compared. The IC 50 values of the 4 chelators (0.06-2.7 mM) and 5 metal ions (0.02-1.09 mM) were significantly lower than those of the 4 amines (10.6-29.1 mM) and 5 organic solvents (3.5-82 mM). Although it did not show any inhibition within 25 min, 0.1 mM Cu 2+ completely inhibited anammox activity in 240 min, suggesting that the inhibitory effect caused by Cu 2+ is time-dependent. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  6. A structured understanding of cellobiohydrolase I binding to poplar lignin fractions after dilute acid pretreatment.

    Science.gov (United States)

    Yao, Lan; Yoo, Chang Geun; Meng, Xianzhi; Li, Mi; Pu, Yunqiao; Ragauskas, Arthur J; Yang, Haitao

    2018-01-01

    Cellulase adsorption to lignin is considered a cost barrier for bioethanol production; however, its detailed association mechanism is still not fully understood. In this study, two natural poplar variants with high and low sugar release performance were selected as the low and high recalcitrant raw materials (named L and H , respectively). Three different lignin fractions were extracted using ethanol, followed by p -dioxane and then cellulase treatment from the dilute acid pretreated poplar solids (fraction 1, 2, and 3, respectively). Each lignin fraction had different physicochemical properties. Ethanol-extracted lignin had the lowest weight average molecular weight, while the molecular weights for the other two lignin fractions were similar. 31 P NMR analysis revealed that lignin fraction with higher molecular weight contained more aliphatic hydroxyl groups and less phenolic hydroxyl groups. Semi-quantitative analysis by 2D HSQC NMR indicated that the lignin fractions isolated from the natural variants had different contents of syringyl (S), guaiacyl (G) and interunit linkages. Lignin extracted by ethanol contained the largest amount of S units, the smallest amounts of G and p -hydroxybenzoate (PB) subunits, while the contents of these lignin subunits in the other two lignin fractions were similar. The lignin fraction obtained after cellulase treatment was primarily comprised of β- O -4 linkages with small amounts of β-5 and β-β linkages. The binding strength of these three lignin fractions obtained by Langmuir equations were in the order of L 1  >  L 3  >  L 2 for the low recalcitrance poplar and H 1  >  H 2  >  H 3 for the high recalcitrance poplar. Overall, adsorption ability of lignin was correlated with the sugar release of poplar. Structural features of lignin were associated with its binding to CBH. For natural poplar variants, lignin fractions with lower molecular weight and polydispersity index (PDI) exhibited more CBH adsorption

  7. Theoretical study of the reaction kinetics of atomic bromine with tetrahydropyran

    KAUST Repository

    Giri, Binod

    2015-02-12

    A detailed theoretical analysis of the reaction of atomic bromine with tetrahydropyran (THP, C5H10O) was performed using several ab initio methods and statistical rate theory calculations. Initial geometries of all species involved in the potential energy surface of the title reaction were obtained at the B3LYP/cc-pVTZ level of theory. These molecular geometries were reoptimized using three different meta-generalized gradient approximation (meta-GGA) functionals. Single-point energies of the stationary points were obtained by employing the coupled-cluster with single and double excitations (CCSD) and fourth-order Møller-Plesset (MP4 SDQ) levels of theory. The computed CCSD and MP4(SDQ) energies for optimized structures at various DFT functionals were found to be consistent within 2 kJ mol-1. For a more accurate energetic description, single-point calculations at the CCSD(T)/CBS level of theory were performed for the minimum structures and transition states optimized at the B3LYP/cc-pVTZ level of theory. Similar to other ether + Br reactions, it was found that the tetrahydropyran + Br reaction proceeds in an overall endothermic addition-elimination mechanism via a number of intermediates. However, the reactivity of various ethers with atomic bromine was found to vary substantially. In contrast with the 1,4-dioxane + Br reaction, the chair form of the addition complex (c-C5H10O-Br) for THP + Br does not need to undergo ring inversion to form a boat conformer (b-C4H8O2-Br) before the intramolecular H-shift can occur to eventually release HBr. Instead, a direct, yet more favorable route was mapped out on the potential energy surface of the THP + Br reaction. The rate coefficients for all relevant steps involved in the reaction mechanism were computed using the energetics of coupled cluster calculations. On the basis of the results of the CCSD(T)/CBS//B3LYP/cc-pVTZ level of theory, the calculated overall rate coefficients can be expressed as kov.,calc.(T) = 4.60 × 10

  8. Angiopep-2-conjugated poly(ethylene glycol-co-poly(ε-caprolactone polymersomes for dual-targeting drug delivery to glioma in rats

    Directory of Open Access Journals (Sweden)

    Lu F

    2017-03-01

    Full Text Available Fei Lu,1,2 Zhiyong Pang,2,3 Jingjing Zhao,2 Kai Jin,4 Haichun Li,2 Qiang Pang,2 Long Zhang,2 Zhiqing Pang2 1Department of Pharmacy, Xianju People’s Hospital, Xianju, Zhejiang, 2Department of Pharmaceutics, Key Laboratory of Smart Drug Delivery, Ministry of Education and PLA, School of Pharmacy, Fudan University, Shanghai, 3Chongyang Center for Disease Control and Prevention, Xianning, Hubei, 4School of Life Science, Fudan University, Shanghai, People’s Republic of China Abstract: The blood–brain barrier is a formidable obstacle for glioma chemotherapy due to its compact structure and drug efflux ability. In this study, a dual-targeting drug delivery system involving Angiopep-2-conjugated biodegradable polymersomes loaded with doxorubicin (Ang-PS-DOX was developed to exploit transport by the low-density lipoprotein receptor-related protein 1 (LRP1, which is overexpressed in both blood–brain barrier and glioma cells. The polymersomes (PS were prepared using a thin-film hydration method. The PS were loaded with doxorubicin using the pH gradient method (Ang-PS-DOX. The resulting PS were uniformly spherical, with diameters of ~135 nm and with ~159.9 Angiopep-2 molecules on the surface of each PS. The drug-loading capacity and the encapsulation efficiency for doxorubicin were 7.94%±0.17% and 95.0%±1.6%, respectively. Permeability tests demonstrated that the proton diffusion coefficient across the PS membrane was far slower than that across the liposome membrane, and the common logarithm value was linearly dependent on the dioxane content in the external phase. Compared with PS-DOX, Ang-PS-DOX demonstrated significantly higher cellular uptake and stronger cytotoxicity in C6 cells. In vivo pharmacokinetics and brain distribution experiments revealed that Ang-PS-DOX achieved a more extensive distribution and more abundant accumulation in glioma cells than PS-DOX. Moreover, the survival time of glioma-bearing rats treated with Ang-PS-DOX was

  9. Structure and properties of silver sulfate complexes derived from dipyridyl methylthio ligands with secondary donor site

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wen-Hua; Yan, Hao-Jie; Chen, Hui; Liu, Rui-Heng; Li, Ai-Min; Wang, Guo [Beijing Key Laboratory for Optical Materials and Photonic Devices, Department of Chemistry, Capital Normal University, Beijing 100048 (China); Wan, Chong-Qing, E-mail: wancq@cnu.edu.cn [Beijing Key Laboratory for Optical Materials and Photonic Devices, Department of Chemistry, Capital Normal University, Beijing 100048 (China); State Key Laboratory of Structural Chemistry in China, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China)

    2017-06-15

    Dipyridyl sulphide ligands 4-(pyridin-4-ylmethylthio)pyridine (abbreviated as L1) and 3-(pyridin-4-ylmethylthio)pyridine (abbreviated as L2) have been designed and used as μ-{sub N},{sub N}-bridging linkages to construct coordination polymers with free –S–CH{sub 2}– groups as secondary donor sites. By use solvent control method, coordination polymers ([Ag{sub 3}SO{sub 4}(L1){sub 3}](Cl)·4.5H{sub 2}O){sub ∞}(1), ([Ag{sub 2}SO{sub 4}(L1){sub 2}]·6H{sub 2}O·2CH{sub 3}OH){sub ∞}(2), ([Ag{sub 2}SO{sub 4}(L2){sub 2}]·H{sub 2}O){sub ∞}(3) and ([Ag{sub 4}(SO{sub 4}){sub 2}(L2){sub 4}]·5H{sub 2}O){sub ∞}(4) with different architectures were obtained. Complexes 1, 3 and 4 feature 1D channel with different sizes and structures. Complex 1 exhibits guest exchange by THF and 1,4-dioxane, and Hg{sup 2+} sorption ability from solution due to its relative larger channel and available bonding sites of –S– exposed to the channel region. All complexes have been characterized through single-crystal and powder X-ray diffraction (PXRD), FT-IR spectra, X-ray photoelectron spectroscopy (XPS), elemental and thermogravimetric analyses. The guest exchange and Hg{sup 2+} sorption were monitored and identified, and the structure-property relationship of coordination polymers 1–4 are discussed. - Graphical abstract: Coordination polymers of silver(I) sulfate with secondary donor sites are shown guest exchange property and Hg{sup 2+} absorb ability from solution. This work provides a new method to construct functional materials with potential application. - Highlights: • New example of constructing functional coordination polymer with secondary donor methylthio group. • Guest exchange and interesting Hg(II) absorb ability from solution are investigated. • New method to construct functional materials with potential application.

  10. Olefins metathesis, synthesis and properties of homogeneous models of the Re{sub 2}O{sub 7}/Al{sub 2}O{sub 3} catalyst; Methathese des olefines, synthese et proprietes des modeles homogenes du catalyseur Re{sub 2}O{sub 7}/Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Doledec, G.

    1999-10-05

    The aim of this work was to synthesize and to study homogeneous models of the rhenium oxide on alumina catalyst in order to better understand the influence of the alumina environment over the activity in olefin metathesis. A series of aluminium complexes (ArO){sub 2}Al-Y have been synthesised, where ArO is a 4-substituted-2,6-di-tert-butyl-phenoxy, or (ArO){sub 2} is a CH{sub 2{sup -}} or S-ortho bridged-4,4'-di-tert-butyl-di-phenoxy, and Y is an alkyl or chlorine ligand. The reaction of (ArO){sub 2}Al-Cl with AgReO{sub 4} led to new complexes (ArO){sub 2}Al-OReO{sub 3} (A). These complexes exhibit a low to moderate activity in metathesis of 2-pentene (TOF = 0,5 min{sup -1} at 25 deg. C in a toluene solution). Complexes (ArO){sub 2}Al-R (R = iBu, Et) react with Re{sub 2}O{sub 7} in THF or dioxane giving type B complexes including oligomeric linkages like O{sub 3}Re-[Al(OAr)-O){sub 2}-ReO{sub 3}. They show a fairly high activity in the metathesis of 2-pentene, with TOF values as high as 100 min{sup -1}. As far as we know, these are the most active rhenium-based homogeneous metathesis catalysts. Complexes type A may be converted into type B complexes upon reaction with (ArO){sub 2}Al-R in an ether solvent. The high activity of B complexes is tentatively related to the Al-O-Al linkages that are molecular in the homogeneous models or present at the surface of the alumina in the heterogeneous catalyst. These results bear out again the role of the Lewis acidity in these catalysts. We used (ArO){sub 2}Al-R complexes to modify the heterogenous catalyst. It appears that it is an excellent way to reduce the rhenium loading without any loss of activity. (author)

  11. The optical behavior of amorphous microribbons for hydroxy-naphthol based Schiff bases

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Ping; Liu, Chunlin; Yang, Wei; Liu, Xuan; Du, Jinya [College of Biological and Pharmaceutical Science, China Three Gorges University, Yichang 443002 (China); Liu, Yi [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Yang, Changying, E-mail: changying.yang@ctgu.edu.cn [College of Biological and Pharmaceutical Science, China Three Gorges University, Yichang 443002 (China)

    2017-05-15

    The optical behaviors of three hydroxy-naphthol based Schiff bases, L1, L2 and L3, in aggregated states in 1,4-dioxane (Diox) – H{sub 2}O mixture, were investigated. The intermolecular hydrogen bond between luminogen and water resulted in the twisting of benzothiazole group, which is favorable for the assembly of organic molecules into J-aggregates. And also a bathochromic shift in absorption and enhancement of the fluorescence emission (aggregation-induced enhanced emission, AIEE) can be observed. L1 and L2 in Diox-H{sub 2}O mixture with water volume fractions (f{sub w}) 95% assembled into microribbons with 40–50 nm thickness, twisted together to make amorphous supramolecular organogels. Whereas L3 assembled into needle-like nanorods with the thickness up to ~200 nm, consistence with its lower emission intensity compared to L1, L2 aggregates. Moreover, a drastic blue-shift and an enhancement of emission efficiency of L1-L3 were also observed in solid states with the morphology change from the crystalline to the amorphous state by grinding. It was found that L1 aggregates showed fluorescence switch-off sensing towards Cu{sup 2+}, with higher selectivity and sensitivity compared to L1 in Diox solution. - Graphical abstract: Three Schiff bases derivatives, L1, L2 and L3, consisting of hydroxy-naphthol and thiazole group, exhibited AIEE effect in Diox-H{sub 2}O mixture with f{sub w} 95% (for L1 and L2) or 99% (for L3). The formation of amorphous nanoparticles is advantageous for emission enhancement. The drastic blue-shift and an enhancement of emission efficiency were also observed in L1-L3 with the morphology change from the crystalline to the amorphous state in solid by grinding. It was found that L1 AIEE system could be constructed as a chemoprobe towards Cu{sup 2+} fluorescence recognition, with higher selectivity and sensitivity compared to L1 in Diox solution.

  12. Strong and long-lasting antinociceptive and anti-inflammatory conjugate of naturally occurring oleanolic acid and aspirin

    Directory of Open Access Journals (Sweden)

    Barbara Bednarczyk-Cwynar

    2016-07-01

    Full Text Available The conjugate 8 was obtained as a result of condensation of 3-hydroxyiminooleanolic acid morfolide (7 and aspirin in dioxane. Analgesic effect of OAO-ASA (8 for the range of doses 0.3 – 300.0 mg/kg (p.o. was performed in mice using a hot plate test. Anti-inflammatory activity was assessed on carrageenan-induced paw edema in rats for the same range of doses. The conjugate OAO-ASA (8 did not significantly change locomotor activity of mice, therefore sedative properties of the compound should be excluded. The compound 8 proved a simple, proportional, dose-dependent analgesic action and expressed strong anti-inflammatory activity showing a reversed U-shaped, dose-dependent relation with its maximum at 30.0 mg/kg. After its combined administration with morphine (MF, 5.0 mg/kg, s.c. the lowering of antinociceptive activity was found; however, the interaction with naloxone (NL, 3.0 mg/kg, s.c. did not affect the antinociceptive effect of OAO-ASA (8, therefore its opioid mechanism of action should be rather excluded. After combined administration with acetylsalicylic acid (ASA, 300.0 mg/kg, p.o. in hot-plate test, the examined compound 8 enhanced the antinociceptive activity in significant way. It also shows that rather the whole molecule is responsible for the antinociceptive and anti-inflammatory effect of the tested compound 8, however it cannot be excluded that the summarizing effect is produced by ASA released from the compound 8 and the rest of triterpene derivative. The occurrence of tolerance for triterpenic derivative 8 was not observed, since the analgesic and anti-inflammatory effects after chronic administration of the conjugate OAO-ASA (8 was on the same level as after its single treatment. It seemed that the anti-inflammatory mechanism of action of OAO-ASA (8 is not simple, even its chronic administration lowered both blood concentration of IL-6 and mRNA IL-6 expression. However, the effects of the conjugate OAO-ASA (8 on TNF-α level

  13. Preparation of 99mTc-HYNIC-PEG-liposomes for imaging of the focal sites infection

    International Nuclear Information System (INIS)

    Hong, Jun Pyo; Awh, Ok Doo; Kim, Hyun Suk; Lee, Eun Sook; Lee, Tae Sup; Choi, Tae Hyun; Choi, Chang Woon; Lim, Sang Moo

    2002-01-01

    A new linker, hydrazino nicotinamide (HYNIC), was recently introduced for labelling of liposome with 99m Tc. In this study we synthesized HYNIC derivatized PEG (polyethylene glycol)-liposomes radiolabeled with 99m Tc. In order to synthesize HYNIC-DSPE (distearoyl phosphatidyl ethanolamine) which is a crucial component for 99m Tc chelation, first of all succinimidyl 6-BOC-hydrazinopyridine-3-carboxylic acid was synthesized from 6-chloronicotinic acid by three sequential reactions. A DSPE derivative of succinimidyl 6-BOC-hydrazinopyridine-3-carboxylic acid was transformed into HYNIC-DSPE by HCI/dioxane. HYNIC-PEG-liposomes were prepared by hydration of the dried lipid mixture of EPC (egg phosphatidyl choline): PEG-DSPE : HYNIC-DSPE: cholesterol (1.85:0.15:0.07:1, molar ratio). The HYNIC-PEG-liposomes were labeled with 99m Tc in the presence of SnCl 2 ·2H 2 O (a reducing agent) and tricine (a colignad). To investigate the level of in vivo transchelation of 99m Tc in the liposomes, the 99m Tc-HYNIC-PEG-liposomes were incubated with a molar excess of DTPA, cysteine or glutathione solutions at 37 .deg. C for 24 hours. 6-BOC-hydrazinopyridine-3-carboxylic acid was synthesized with 77.3% overall yield. The HYNIC concentration in the PEG-coated liposome dispersion was 1.08 mM. In condition of considering the measured liposome size of 106 nm, the phospholipid concentration of 77.5 μmol/ ml and the liposomal particle number of 5.2x10 14 liposomes/ml, it is corresponded to approximate 1,250 nicotinyl hydrazine group per liposome in HYNIC-PEG-liposome. The removal of free 99m Tc was not necessary because the labeling efficiency were above 99%. The radiolabeled liposomes maintained 98%, 96% and 99%, respectively, of radioactivity after incubation with transchelators. The radiolabeled liposomes possessed above 90% of the radioactivity in serum. These results suggest that the HYNIC can be synthesized easily and applied in labelling of PEG-liposomes with 99m Tc

  14. Cefazolin-containing poly(ε-caprolactone sponge pad to reduce pin tract infection rate in rabbits

    Directory of Open Access Journals (Sweden)

    Hirotaka Mutsuzaki

    2014-04-01

    Full Text Available In our previous study, a fibroblast growth factor-2 (FGF-2–apatite composite layer coated on titanium screws effectively prevented pin tract infection in rabbits because of enhanced wound healing; however, the FGF-2–apatite composite layers did not completely prevent pin tract infection. Thus, we recently developed a poly(ε-caprolactone (PCL sponge pad embedded with cefazolin sodium (+CEZ, which has a fast-acting bactericidal effect. The pad is placed on the skin around the screws. The purpose of this study was to determine the anti-infective efficacy of the +CEZ pad on the pin–skin interface of the FGF-2–apatite-coated titanium screws. The +CEZ pads were prepared by mixing PCL and CEZ in 1,4-dioxane, followed by freeze-drying and compaction. They were analyzed regarding their surface structure, in vitro CEZ release profile, and bactericidal activity. The FGF-2–apatite-coated screws were implanted percutaneously in bilateral rabbit proximal tibial metaphyses—with and without the +CEZ pad—for 4 weeks (n = 20. The + CEZ pads consisted of a porous matrix of PCL in which CEZ was embedded. The CEZ-release profile showed an initial burst on Day 1 and a sustained release lasting for 30 days. The +CEZ pad retained its bactericidal activity against Staphylococcus aureus after preincubation on an agar plate for 7 days. Based on visual inspection, the pin tract infection rate was successfully reduced from 72.2% to 15.0% with the +CEZ pad (p < 0.05, which reduced the bacterial count, especially S. aureus (p < 0.05. The histological inflammation rate of the soft tissues was also significantly lower with the +CEZ pad than without it (p < 0.05. The pin tract infection rate was reduced to one-fifth with the +CEZ pad. Using it as described improves infection resistance during percutaneous implantation.

  15. Scintillating Cocktail Mixtures and the Role of Water on the Optophysical Properties.

    Energy Technology Data Exchange (ETDEWEB)

    Cordaro, Joseph Gabriel [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Feng, Patrick L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Mengesha, Wondwosen [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Murtagh, Dustin [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Anstey, Mitchell [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-10-01

    Two types of water - containing liquid scinti llation mixtures were prepared in the present work. In the first, m ixtures of 2 - phenylethanol, water, diphenyl phosphate, sodium phenyl phosphate dibasic dihydrate, and the dye 2,5 - diphenyloxazole (PPO) have been investigated as liquid scintillators. In th e second system, nonionic and mixed surfactant systems were investigated in conjunction with water and small amounts of toluene. In both cases, increasing amounts of water led to reductions in the scintillation light yield. Understanding what factors contr ibute to this phenomenon is the focus of this report. Changes in the solution microphase structure, diminishing aromatic content of the cocktail mixtures, and inefficient energy transfer to the dye a ppear to be responsible for the decreased light yield as more water is added . In the 2 - phenylethanol system, the observed experimental results are consistent with the formation of a bicontinuous microemulsion at higher water concentrations, which incorporates PPO and shields it from the quenching effects of the increasing polar matrix. Evidence for this proposed phase chan ge c ome s from light scattering data, photo - and x - ray luminescence measurements, and optical transparency measurements . In the surfactant - based system, the quenching effect of water was found to be less than both commercially - available dioxane - naphthalene mixtures used for scintillation counting as well as the 2 - phenylethanol mixtures described above. The effect of different surfactant mixtures and concentrations were studied, revealing a benefic ial effect upon the scintillation light yield for mixed surfactant mixtures. These results are interpreted in the context of r eactive radical species formation following water ionization , which leads to light - yield quenching in aqueous systems . The presenc e of surfactant(s) in these mixtures enables the formation of organic - rich regions that are spatially separated from the

  16. Tautomeric and Microscopic Protonation Equilibria of Anthranilic Acid and Its Derivatives.

    Science.gov (United States)

    Zapała, Lidia; Woźnicka, Elżbieta; Kalembkiewicz, Jan

    2014-01-01

    The acid-base chemistry of three zwitterionic compounds, namely anthranilic (2-aminobenzoic acid), N -methylanthranilic and N -phenylanthranilic acid has been characterized in terms of the macroconstants K a1 , K a2 , the isoelectric point p H I , the tautomerization constant K z and microconstants k 11 , k 12 , k 21 , k 22 . The potentiometric titration method was used to determine the macrodissociation constants. Due to the very poor water solubility of N -phenylanthranilic acid the dissociation constants p K a1 and p K a2 were determined in MDM-water mixtures [MDM is a co-solvent mixture, consisting of equal volumes of methanol (MeOH), dioxane and acetonitrile (MeCN)]. The Yasuda-Shedlovsky extrapolation procedure has been used to obtain the values of p K a1 and p K a2 in aqueous solutions. The p K a1 and p K a2 values obtained by this method are 2.86 ± 0.01 and 4.69 ± 0.03, respectively. The tautomerization constant K z describing the equilibrium between unionized form ⇌ zwitterionic form was evaluated by the K z method based on UV-VIS spectrometry. The method uses spectral differences between the zwitterionic form (found at isoelectric pH in aqueous solution) and the unionized form (formed in an organic solvent of low dielectric constant). The highest value of the K z constant has been observed in the case of N -methylantranilic acid (log 10 K z  = 1.31 ± 0.04). The values of log 10 K z for anthranilic and N -phenylanthranilic acids are similar and have values of 0.93 ± 0.03 and 0.90 ± 0.05, respectively. The results indicate that the tested compounds, in aqueous solution around the isoelectric point pH I , occur mainly in the zwitterionic form. Moreover, the influence of the type of substituent and pH of the aqueous phase on the equilibrium were analyzed with regard to the formation and the coexistence of different forms of the acids in the examined systems.

  17. Cobalt bis(dicarbollide) ions with covalently bonded CMPO groups as selective extraction agents for lanthanide and actinide cations from highly acidic nuclear waste solutions

    International Nuclear Information System (INIS)

    Gruner, B.; Plesek, J.; Baca, J.; Cisarova, I.; Dozol, J.F.; Rouquette, H.; Vinas, C.; Selucky, P.; Rais, J.

    2002-01-01

    A new series of boron substituted cobalt bis(dicarbollide)(1-) ion (1) derivatives of the general formula [(8-CMPO-(CH 2 -CH 2 O) 2 -1,2-C 2 B 9 H 10 )(1',2'-C 2 B 9 H 11 )-3,3'-Co] - (CMPO = Ph 2 P(O)-CH 2 C(O)NR, R = C 4 H 9 (3b), -C 12 H 25 (4b), -CH 2 -C 6 H 5 (5b)) was prepared by ring cleavage of the 8-dioxane-cobalt bis(dicarbollide) (2) bi-polar compound by the respective primary amines and by subsequent reaction of the resulting amino derivatives (3a-5a) with the nitrophenyl ester of diphenyl-phosphoryl-acetic acid. The compounds were synthesized with the aim to develop a new class of more efficient extraction agents for liquid/liquid extraction of polyvalent cations, i.e. lanthanides and actinides, from high-level activity nuclear waste. All compounds were characterized by a combination of 11 B NMR, 1 H high field NMR, Mass Spectrometry with Electro-spray and MALDI TOF ionisation, HPLC and other techniques. The molecular structure of the supramolecular Ln 3+ complex of the anion 5b was determined by single crystal X-ray diffraction analysis. Crystallographic results proved that the Ln(m) atom is bonded to three functionalized cobalt bis(dicarbollide) anions in a charge compensated complex. The cation is tightly coordinated by six oxygen atoms of the CMPO terminal groups (two of each ligand) and by three water molecules completing the metal coordination number to 9. Atoms occupying the primary coordination sphere form a tri-capped trigonal prismatic arrangement. Very high liquid-liquid extraction efficiency of all anionic species was observed. Moreover, less polar toluene can be applied as an auxiliary solvent replacing the less environmentally friendly nitro- and chlorinated solvents used in the current dicarbollide liquid-liquid extraction process. The extraction coefficients are sufficiently high for possible technological applications. (authors)

  18. Kinetic analysis of the reactivity of aliphatic cyclic alcohols and carboxylic acids in the T-for-H exchange reaction

    International Nuclear Information System (INIS)

    Tamura, Kiyoshi; Imaizumi, Hiroshi; Kano, Naoki

    2007-01-01

    aliphatic normal carboxylic acid. (7) The reactivity of these materials dissolved in 1,4-dioxane is smaller than that in p-xylene. (8) Using both the MOPAC and the A''-McKay plot methods, the actual analysis of aliphatic cyclic alcohols can be more possible. (9) The method used in this work is useful for evaluating influence of T on environment. (author)

  19. Determination of diffusion and adsorption coefficients for some contaminants in clayey soil and rock: Laboratory determination and field evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Barone, F S

    1990-01-01

    A laboratory diffusion test determination of diffusion coefficient (D) and adsorption coefficient (K{sub d}) for various inorganic and organic species in a saturated, undisturbed, clayey soil is presented. Diffusion tests conducted for inorganic species (Cl{sup {minus}} , Na{sup +}, K{sup +}, Mg{sup 2+}, and Ca{sup 2+}), involved placing domestic landfill leachate on top of a layer of clay and allowing the chemical constituents to diffuse into the soil. The mathematical model POLLUTE was then used to back-figure (D) and (K{sub d}) for each species. Diffusion tests conducted for organic species (acetone, 1,4-dioxane, aniline, chloroform, and toluene), involved diffusion of the species from a source solution placed on one side of a clay plug, into a distilled water collector solution on the opposite side. Using POLLUTE, D and K{sub d} were then determined by fitting the measured concentration variation with time in both the source and collector solution. In addition to the laboratory study, an investigation of inorganic contaminant diffusion below an existing industrial landfill site was conducted by analyzing soil and pore water specimens from the clay layer underlying the waste. Concentration profiles for Cl{sup {minus}}, So{sub 4}{sup 2{minus}}, Na+, Ca{sup 2+} and Mg{sup 2+}, showed above background levels to a depth of 1.4 m below the waste after 11 years of migration. K{sup +}, B, and NH{sub 3}-N profiles, penetrated to less than 0.5 m below the waste. Field profiles for Na{sup +}, K{sup +}, Cl{sup {minus}}, and SO{sub 4}{sup 2{minus}} were then compared with those predicted using POLLUTE with D and K{sub d} values obtained from diffusion tests using leachate and natural uncontaminated clay from the site. Finally, a laboratory diffusion test determination of Cl{sup {minus}} diffusion coefficient in samples of intact, saturated shale and mudstone is presented.

  20. Preparation and isolation of dithiolene thiophosphoryl molecules as stable, protected forms of dithiolene ligands.

    Science.gov (United States)

    Arumugam, Kuppuswamy; Bollinger, James E; Fink, Mark; Donahue, James P

    2007-04-16

    The reaction of P4S10 with acyloins, RC(O)CH(OH)R, in refluxing dioxane, followed by the addition of alkylating agents, forms dithiolene thiophosphoryl thiolate compounds, (R2C2S2)P(S)(SR'), which are readily isolated and purified. The compounds that have been prepared and identified spectroscopically are those with R = p-anisyl, R' = Me (1); R = p-anisyl, R' = Bz (2); R = Ph, R' = Me (4); R = Et, R' = Bz (5). Compounds 1, 2, and 4 were structurally characterized by X-ray crystallography and found to possess a tetrahedral coordination geometry about the phosphorus atom, with overall Cs symmetry. In each case, the mirror plane bisects the dithiolene S-P-S chelate and contains the thiophosphoryl bond, which ranges in length from 1.9241(8) to 1.9361(7) A. The use of 2-(bromomethyl)naphthalene as organic electrophile in the P4S10/acyloin reaction produced bis(2-methylnaphthalenyl) disulfide as the only identifiable product. The substitution of Lawesson's reagent for P4S10 in reactions with acyloins produced deoxy acyloin rather than products resulting from chalcogen exchange. Compounds 1-2 and 4-5 are Group 5 analogues of 1,3-dithiol-2-ones, (R2C2S2)C=O, and undergo a similar hydrolysis in aqueous base to liberate ene-1,2-dithiolate dianions from which corresponding metal dithiolene complexes may be prepared. Deprotection of 1 in MeO-/MeOH, followed by the addition of NiCl2.6H2O and then I2, produces square planar [Ni(S2C2(C6H4-p-OCH3)2)2] (8) in 93% yield. A high-resolution structure of 8 (P) reveals dithiolene C-C and C-S bond lengths that are clearly indicative of the thionyl radical monoanionic nature of the ligand. The use of isolated (R2C2S2)P(S)(SR') compounds as a dithiolene ligand source for the preparation of metal dithiolene complexes offers the advantages of clean reactivity and high yield.

  1. Safety assessment on polyethylene glycols (PEGs) and their derivatives as used in cosmetic products

    International Nuclear Information System (INIS)

    Fruijtier-Poelloth, Claudia

    2005-01-01

    , however, considered safe as they are not expected to be systemically available. As all PEGs and PEG derivatives, they must not be applied to damaged skin. Manufacturers of PEGs and PEG derivatives must continue their efforts to remove impurities and by-products such as ethylene oxide and 1,4-dioxane. Overall, it is concluded, that the PEGs covered in this review are safe for use in cosmetics under the present conditions of intended use

  2. Enhanced Ga2O3-photocatalyzed and photochemical degradation of the Fipronil insecticide by UVC irradiation in mixed aqueous/organic media under an inert atmosphere.

    Science.gov (United States)

    Hidaka, Hisao; Tsukamoto, Tohru; Mitsutsuka, Yoshihiro; Oyama, Toshiyuki; Serpone, Nick

    2015-05-01

    Agrochemicals such as the insecticide Fipronil that bear fluoro groups are generally fat-soluble and nearly insoluble in water, so that their photodegradation in a heterogeneous aqueous gallium oxide dispersion presents some challenges. This article examined the photodegradation of this insecticide by solubilizing it through the addition of organic solvents (EtOH, MeOH, THF, 1,4-dioxane and ethylene glycol) to an aqueous medium and then subjecting the insecticide to 254 nm UVC radiation under photocatalytically inert (Ga2O3/N2) and air-equilibrated (Ga2O3/O2) conditions, as well as photochemically in the absence of Ga2O3 but also under inert and air-equilibrated conditions. Defluorination, dechlorination, desulfonation and denitridation of Fipronil were examined in mixed aqueous/organic media (10, 25 and 50 vol% in organic solvent). After 3 h of UVC irradiation (50 vol% mixed media) defluorination with Ga2O3/N2 was ∼65% greater than in aqueous media, and ca. 80% greater than the direct photolysis of Fipronil under inert (N2) conditions; under air-equilibrated conditions both Ga2O3-photocatalyzed and photochemical defluorination were significantly lower than in aqueous media. Dechlorination of Fipronil was ∼160% (Ga2O3/N2) and 140% (photochemically, N2) greater than in aqueous media; under air-equilibrated conditions, both photocatalyzed and photochemical formation of Cl(-) ions in mixed media fell rather short relative to aqueous media. The photocatalyzed (Ga2O3/N2) and photochemical (N2) conversion of the sulfur group in Fipronil to SO4(2(-)) ions was ca. 20% and 30% greater, respectively, in mixed media, while under air-equilibrated conditions photocatalyzed desulfonation was nearly twofold less than in the aqueous phase; direct photolysis showed little variations in mixed media. Denitridation of the nitrogens in Fipronil occurred mostly through the formation of ammonia (as NH4(+)) under all conditions with negligible quantities of NO3(-); again mixed media

  3. Toxicological risk assessment and prioritization of drinking water relevant contaminants of emerging concern.

    Science.gov (United States)

    Baken, Kirsten A; Sjerps, Rosa M A; Schriks, Merijn; van Wezel, Annemarie P

    2018-06-13

    Toxicological risk assessment of contaminants of emerging concern (CEC) in (sources of) drinking water is required to identify potential health risks and prioritize chemicals for abatement or monitoring. In such assessments, concentrations of chemicals in drinking water or sources are compared to either (i) health-based (statutory) drinking water guideline values, (ii) provisional guideline values based on recent toxicity data in absence of drinking water guidelines, or (iii) generic drinking water target values in absence of toxicity data. Here, we performed a toxicological risk assessment for 163 CEC that were selected as relevant for drinking water. This relevance was based on their presence in drinking water and/or groundwater and surface water sources in downstream parts of the Rhine and Meuse, in combination with concentration levels and physicochemical properties. Statutory and provisional drinking water guideline values could be derived from publically available toxicological information for 142 of the CEC. Based on measured concentrations it was concluded that the majority of substances do not occur in concentrations which individually pose an appreciable human health risk. A health concern could however not be excluded for vinylchloride, trichloroethene, bromodichloromethane, aniline, phenol, 2-chlorobenzenamine, mevinphos, 1,4-dioxane, and nitrolotriacetic acid. For part of the selected substances, toxicological risk assessment for drinking water could not be performed since either toxicity data (hazard) or drinking water concentrations (exposure) were lacking. In absence of toxicity data, the Threshold of Toxicological Concern (TTC) approach can be applied for screening level risk assessment. The toxicological information on the selected substances was used to evaluate whether drinking water target values based on existing TTC levels are sufficiently protective for drinking water relevant CEC. Generic drinking water target levels of 37 μg/L for

  4. Carbonyl Activation by Borane Lewis Acid Complexation: Transition States of H2 Splitting at the Activated Carbonyl Carbon Atom in a Lewis Basic Solvent and the Proton-Transfer Dynamics of the Boroalkoxide Intermediate.

    Science.gov (United States)

    Heshmat, Mojgan; Privalov, Timofei

    2017-07-06

    By using transition-state (TS) calculations, we examined how Lewis acid (LA) complexation activates carbonyl compounds in the context of hydrogenation of carbonyl compounds by H 2 in Lewis basic (ethereal) solvents containing borane LAs of the type (C 6 F 5 ) 3 B. According to our calculations, LA complexation does not activate a ketone sufficiently enough for the direct addition of H 2 to the O=C unsaturated bond; but, calculations indicate a possibly facile heterolytic cleavage of H 2 at the activated and thus sufficiently Lewis acidic carbonyl carbon atom with the assistance of the Lewis basic solvent (i.e., 1,4-dioxane or THF). For the solvent-assisted H 2 splitting at the carbonyl carbon atom of (C 6 F 5 ) 3 B adducts with different ketones, a number of TSs are computed and the obtained results are related to insights from experiment. By using the Born-Oppenheimer molecular dynamics with the DFT for electronic structure calculations, the evolution of the (C 6 F 5 ) 3 B-alkoxide ionic intermediate and the proton transfer to the alkoxide oxygen atom were investigated. The results indicate a plausible hydrogenation mechanism with a LA, that is, (C 6 F 5 ) 3 B, as a catalyst, namely, 1) the step of H 2 cleavage that involves a Lewis basic solvent molecule plus the carbonyl carbon atom of thermodynamically stable and experimentally identifiable (C 6 F 5 ) 3 B-ketone adducts in which (C 6 F 5 ) 3 B is the "Lewis acid promoter", 2) the transfer of the solvent-bound proton to the oxygen atom of the (C 6 F 5 ) 3 B-alkoxide intermediate giving the (C 6 F 5 ) 3 B-alcohol adduct, and 3) the S N 2-style displacement of the alcohol by a ketone or a Lewis basic solvent molecule. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Status of groundwater quality in the Coastal Los Angeles Basin, 2006-California GAMA Priority Basin Project

    Science.gov (United States)

    Goldrath, Dara; Fram, Miranda S.; Land, Michael; Belitz, Kenneth

    2012-01-01

    -concentration greater than (>) 1.0 indicates a concentration greater than a benchmark, and a relative-concentration less than or equal to (≤) 1.0 indicates a concentration equal to or less than a benchmark. Relative-concentrations of organic and special-interest constituents [perchlorate, N-nitrosodimethylamine (NDMA), 1,2,3-trichloropropane (1,2,3-TCP), and 1,4-dioxane] were classified as "high" (relative-concentration>1.0), "moderate" (0.5status assessment for evaluating regional-scale groundwater quality. High aquifer-scale proportion is defined as the percentage of the area of the primary aquifer system with a relative-concentration greater than 1.0 for a particular constituent or class of constituents; percentage is based on an areal rather than a volumetric basis. Moderate and low aquifer-scale proportions were defined as the percentage of the primary aquifer system with moderate and low relative-concentrations, respectively. Two statistical approaches-grid-based and spatially weighted-were used to evaluate aquifer-scale proportions for individual constituents and classes of constituents. Grid-based and spatially weighted estimates were comparable in the CLAB study unit (within 90-percent confidence intervals). Inorganic constituents with human-health benchmarks were detected at high relative-concentrations in 5.6 percent of the primary aquifer system and moderate in 26 percent. High aquifer-scale proportion of inorganic constituents primarily reflected high aquifer-scale proportions of arsenic (1.9 percent), nitrate (1.9 percent), and uranium (1.2 percent). Inorganic constituents with secondary maximum contaminant levels (SMCL) were detected at high relative-concentrations in 18 percent of the primary aquifer system and moderate in 47 percent. The constituents present at high relative-concentrations included total dissolved solids (1.9 percent), manganese (15 percent), and iron (9.4 percent). Relative-concentrations of organic constituents (one or more) were high in 3

  6. Influence of methoxy- and nitro-substitutions in the aromatic ring on proton donation ability in hydrogen bond and on the amino group parameters of free and H-bonded molecules of 2-aminopyrimidine

    Science.gov (United States)

    Borisenko, V. E.; Krekov, S. A.; Fomenko, M. Yu.; Koll, A.; Lipkovski, P.

    2008-06-01

    Amino- and imino- forms of pyrimidine are widely presented as part of antibiotics, corrective medications for heart failures and metabolic stimulators. Hydrogen bonding is one of the fundamental interactions between biologically active molecules. This type of interactions provides flexibility, speed and variety of the biochemical processes. Proton donation properties of aminopyrimidines significantly depend on the position, number and kind of the substituent in its aromatic ring. In present work we studied the influence of the methoxy- and nitro-substitutions in the phenyl radical of pyridine and pyrimidine cycles on the proton donation ability of the amino group in hydrogen bonds as well as on its geometrical, force, electro-optical and thermodynamical characteristics in free and H-bonded (1:1 and 1:2, with various proton acceptors) molecules of primary aromatic amines. Acetonitrile, dioxane, tetrahydrofourane, dimethylformamide, dimethylsulfoxide and hexamethylphosphoramide (whose proton accepting properties vary within a wide range) were used as proton acceptors in our research. In the region of the amino group stretching and deformation vibrations the IR spectra of free and H-bonded (1:1) molecules of 2-amino-4,6-dimethoxy- and 2-amino-5-nitropyrimidine were studied in complexes with proton acceptors in CCl 4 within the temperature range 288-328 K. The spectra of 1:2 complexes were studied in undiluted aprotic solvents. The following spectral characteristics of absorption bands in amino group stretching vibrations were determined: M(0) (zero spectral moment, integrated intensity B); M(1) (first spectral moment, band "centre of gravity"); effective half width, related to the second central moment (Δ ν1/2) eff = 2( M(2)) 1/2, frequencies of the deformation vibrations δ(HNH) of free and H-bonded molecules. It was shown that changes of the absorption band spectral characteristics of the amino group stretching and deformation vibrations in the analyzed

  7. Safety assessment of poloxamers 101, 105, 108, 122, 123, 124, 181, 182, 183, 184, 185, 188, 212, 215, 217, 231, 234, 235, 237, 238, 282, 284, 288, 331, 333, 334, 335, 338, 401, 402, 403, and 407, poloxamer 105 benzoate, and poloxamer 182 dibenzoate as used in cosmetics.

    Science.gov (United States)

    Singh-Joy, Subhashni D; McLain, Valerie C

    2008-01-01

    Poloxamers are polyoxyethlyene, polyoxypropylene block polymers. The impurities of commercial grade Poloxamer 188, as an example, include low-molecular-weight substances (aldehydes and both formic and acetic acids), as well as 1,4-dioxane and residual ethylene oxide and propylene oxide. Most Poloxamers function in cosmetics as surfactants, emulsifying agents, cleansing agents, and/or solubilizing agents, and are used in 141 cosmetic products at concentrations from 0.005% to 20%. Poloxamers injected intravenously in animals are rapidly excreted in the urine, with some accumulation in lung, liver, brain, and kidney tissue. In humans, the plasma concentration of Poloxamer 188 (given intravenously) reached a maximum at 1 h, then reached a steady state. Poloxamers generally were ineffective in wound healing, but were effective in reducing postsurgical adhesions in several test systems. Poloxamers can cause hypercholesterolemia and hypertriglyceridemia in animals, but overall, they are relatively nontoxic to animals, with LD(50) values reported from 5 to 34.6 g/kg. Short-term intravenous doses up to 4 g/kg of Poloxamer 108 produced no change in body weights, but did result in diffuse hepatocellular vacuolization, renal tubular dilation in kidneys, and dose-dependent vacuolization of epithelial cells in the proximal convoluted tubules. A short-term inhalation toxicity study of Poloxamer 101 at 97 mg/m(3) identified slight alveolitis after 2 weeks of exposure, which subsided in the 2-week postexposure observation period. A short-term dermal toxicity study of Poloxamer 184 in rabbits at doses up to 1000 mg/kg produced slight erythema and slight intradermal inflammatory response on histological examination, but no dose-dependent body weight, hematology, blood chemistry, or organ weight changes. A 6-month feeding study in rats and dogs of Poloxamer 188 at exposures up to 5% in the diet produced no adverse effects. Likewise, Poloxamer 331 (tested up to 0.5 g/kg day(-1

  8. Synthesis and physical-chemical properties of 8-benzylidenhydrazino-1-(4-fluorobenzyltheobromine derivatives

    Directory of Open Access Journals (Sweden)

    D. G. Ivanchenko

    2014-12-01

    Full Text Available The aim of the work is thesynthesis and research of physical and chemical properties of earlier undescribed 1,8-disubstituted of theobromine, which are potential biologically active compounds. Materials and Methods of Research The melting point has been determined with the help of an open capillary method with TAP device (M. Elemental analysis has been performed with the help of the instrument ElementarVario L cube, NMR-spectra have been taken on a spectrometer Bruker SF-400 (operating frequency of 400 MHz, solvent DMSO-d6, internal standard – TMS. IR-spectra have been taken on Bruker Alpha Device Company in the 4000-400 cm-1area using console ATR (direct input material.These data correspond to thecalculated elemental analysis. Results and their discussion To achieve our goal, 8-bromotheobromine (1, obtained by the established method [9] of oxidizing theobrominebromination, has been selected as initial compound.8-Bromo-1-(4-fluorobenzyltheobromine (2has been synthesized with high entrance by bromotheobromine(1 and p-fluorobenzylchlorideboiling in dimethylformamide, in the presence of anequimolaramount of potassium caronate. Through the interaction of bromoxanthine (2 with the excess of hydrazine hydrate in the aqueous dioxanean 8-hydrazine-1(4-fluorobenzyltheobromine (3has been obtained, which under short-time heating up with aldehydes, isatin or 5-bromoisatin in aqueous dioxane, also presented with equimolaramount of НClconcentr.form respective ylidenhydrazine derivatives of 1-(4-fluorobenzyltheobromine(4-13,which represent coloured crystalline compounds, insoluble in water, diethyl ether and lower alcohols, whilesoluble in hot dioxane, dimethylformamide and dimethylsulphoxide. To prove the structure of synthesized compounds, their NMR spectrahave beenrecorded and interpreted. In bromoxanthine spectrum (2 the presence of p-fluorobenzyl group in position 1 is clearly demonstrated by2 triplets of aromatic protons at 7.34 ppm and 7.09ppm with

  9. Final report on the safety assessment of octoxynol-1, octoxynol-3, octoxynol-5, octoxynol-6, octoxynol-7, octoxynol-8, octoxynol-9, octoxynol-10, octoxynol-11, octoxynol-12, octoxynol-13, octoxynol-16, octoxynol-20, octoxynol-25, octoxynol-30, octoxynol-33, octoxynol-40, octoxynol-70, octoxynol-9 carboxylic acid, octoxynol-20 carboxylic acid, potassium octoxynol-12 phosphate, sodium octoxynol-2 ethane sulfonate, sodium octoxynol-2 sulfate, sodium octoxynol-6 sulfate, and sodium octoxynol-9 sulfate.

    Science.gov (United States)

    Johnson, Wilbur

    2004-01-01

    Octoxynols are ethoxylated alkylphenols in which the size of the molecule is related to the number of moles of ethylene oxide used in synthesis. Reactions are performed at elevated temperature, under pressure, and in the presence of NaOH. It is possible that the synthesis may leave trace amounts of ethylene oxide, 1,4-dioxane, and unreacted C9 phenols. Octoxynols of various chain lengths as well as octoxynol salts and organic acids function in cosmetics either as surfactants--emulsifying agents, surfactants--cleansing agents, surfactant--solubilizing agents, or surfactants--hydrotropes in a wide variety of cosmetic products at concentrations ranging from 0.0008% to 25%, with most less than 5.0%. The octoxynols are chemically similar to nonoxynols, the safety of which were previously considered. Long-chain nonoxynols (9 and above) were considered safe as used, whereas short-chain nonoxynols (8 and below) were considered safe as used in rinse-off products and safe at concentrations less than 5% in leave-on formulations. Acute exposure of hamsters to Octoxynol-9 by bronchopulmonary lavage produced pneumonia, pulmonary edema, and intra-alveolar hemorrhage. Octoxynol-9 at doses over 1 g/kg was toxic in rats and in mice in acute oral toxicity studies. No significant effects were noted in short-term oral studies of Octoxynol-9 in rats, in subchronic oral studies of Octoxynol-40 in rats and dogs, or in chronic oral studies of Octoxynol-40 in rats. The intraperitoneal LD50 of Octoxynol-9 in rats and mice was around 100 mg/kg. In skin irritation studies, octoxynols ranged from nonirritating to moderately irritating. Octoxynols were not ocular irritants in one rabbit study, but in others there was ocular irritation. No immune system toxicity in CF-1 female mice was noted following the intraperitoneal injection of Octoxynol-9 followed by subcutaneous immunization with sheep red blood cells (SRBCs). Octoxynol-9 produced no humoral and cell-mediated immune responses, or

  10. Research on the structure in solution of optically active synthetic polymers (propylene polysulphide, propylene polyoxide, tertio-butyl polysulphide); Recherche de la structure en solution de polymeres synthetiques, optiquement actifs (polysulfure de propylene, polyoxyde de propylene, polysulfure de tertiobutyle)

    Energy Technology Data Exchange (ETDEWEB)

    Sarrazin, Brigitte

    1971-03-15

    It was proposed to study the structure of sulphur-containing synthetic polymers, stereo-regular, optically active in solution and able to adopt a spiral conformation, with special reference to propylene polysulphide. Two methods were used, the first mathematical (conformational energy calculations) and the second physico-chemical, essentially spectroscopic. By conformational analysis it is possible to choose the most probable structures liable to be adopted by a given polymer in solution while the spectro-polarimetric study should, in principle, invalidate or confirm certain of these hypotheses. The conformational energy calculations showed that in fact there is no energy conformation low enough to be stable in solution. Strictly speaking however we can refer to a region of stability in which steric hindrance is low and many energy minima exist. These minima are indistinguishable both by their energy values and by their spatial localizations and are all enclosed in the region bounded by the barriers due to steric hindrance. This uncertainty does not arise from approximations made in the calculations, but from the multitude of stereochemical structure possible. Investigations into the variation of the optical rotary dispersion and the circular dichroism as a function of temperature indicated the existence of three or more equilibrium states in the dioxane. The spectra appear to be the summation of the optical activities of the numerous simultaneously possible conformations. It appears that polymers, such as propylene polysulphide or propylene polyoxide do not have stable structures in solution. These are molecules of great flexibility possessing a large number of degrees of freedom. These properties distinguish them from the natural polymers, carrying precise information, such as DNA which must consequently have stable conformations. (author) [French] On s'est propose d'etudier la structure de polymeres synthetiques soufres, stereoreguliers, optiquement actifs en

  11. Donor-acceptor interaction between non-aqueous solvents and I{sub 2} to generate I{sup -}{sub 3}, and its implication in dye sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Kebede, Zerihun [Department of Chemistry, Kotebe College of Teacher Education, P.O. Box 31248, Addis Ababa (Ethiopia); Lindquist, Sten-Eric [Department of Physical Chemistry, Uppsala University, P.O. Box 532, S-751 21 Uppsala (Sweden)

    1999-03-16

    The spectrophotometric properties of I{sup -}, I{sub 2} and the I{sup -}/I{sub 2} mixture were studied in 1,2-dichloroethane (DCE), acetone (AC), acetonitrile (ACN), ethanol (EtOH), methanol (MeOH), tertiary-butanol (t-BuOH), dimethylformamide (DMF), propylenecarbonate (PC), 3-methoxypropionitrile (MePN), dimethylsulfoxide (DMSO), dioxane (DIO) and pyridine (PY) solutions. From the investigation it has been realized that in DCE, I{sup -}, I{sub 2} and I{sup -}/I{sub 2} mixture have the same absorption peak at 500 nm. I{sup -} gives rise to the absorption spectra at about 220, 290 and 360 nm in t-BuOH and in PY solutions. However, in all other solvents the I{sup -} generates peaks only around 220 nm. Similarly I{sub 2} and the I{sup -}/I{sub 2} mixture in all solvents except DCE have indicated similar absorption peaks around 220, 290 and 360 nm. On the other hand, except in PC and DMF, I{sub 2} shows the additional peaks in the range of 380-500 nm which are assigned to the formation of a I{sub 2}-solvent complex. The peaks around 290 and 360 nm indicate the presence of I{sup -}{sub 3} and around 220 nm is the peak of I{sup -}. The spectral shift of the I{sub 2} solutions in the visible region is interesting and is the core of this report. It points to the importance of donor-acceptor interaction between solvents and iodine. The data obtained in these solvents were well correlated to the donor number (DN) of the solvents. From this correlation the DN of MePN was estimated to 14.6. The absorption peak of I{sub 2} in DCE(DN=0.0) is 500 nm and in PY(DN=33.1) is 378 nm. This peak shift due to solvent effects corresponds to an energy difference close to 0.8 eV. The absorption peak shift due to addition of the 0.0080 vol%. PY(1 mM) in 1 mM I{sub 2}-ACN solutions corresponds to ca. 0.6 eV. The blue shift of I{sub 2} absorption in basic solvents indicates the tendency to form a complex. The increase of the efficiency of the dye-sensitized solar cell by addition of PY to I

  12. Ground-Water Quality Data in the Upper Santa Ana Watershed Study Unit, November 2006-March 2007: Results from the California GAMA Program

    Science.gov (United States)

    Kent, Robert; Belitz, Kenneth

    2009-01-01

    Ground-water quality in the approximately 1,000-square-mile Upper Santa Ana Watershed study unit (USAW) was investigated from November 2006 through March 2007 as part of the Priority Basin Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin project was developed in response to the Groundwater Quality Monitoring Act of 2001, and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The Upper Santa Ana Watershed study was designed to provide a spatially unbiased assessment of raw ground-water quality within USAW, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 99 wells in Riverside and San Bernardino Counties. Ninety of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study unit (grid wells). Nine wells were selected to provide additional understanding of specific water-quality issues identified within the basin (understanding wells). The ground-water samples were analyzed for a large number of organic constituents (volatile organic compounds [VOCs], pesticides and pesticide degradates, pharmaceutical compounds, and potential wastewater-indicator compounds), constituents of special interest (perchlorate, N-nitrosodimethylamine [NDMA], 1,4-dioxane, and 1,2,3-trichloropropane [1,2,3-TCP]), naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), radioactive constituents, and microbial indicators. Naturally occurring isotopes (tritium, carbon-14, and stable isotopes of hydrogen and oxygen in water) and dissolved noble gases also were measured to help identify sources and ages of the sampled ground water. Dissolved gases, and isotopes of nitrogen gas and of dissolved nitrate also were measured in order to investigate the sources and occurrence of

  13. Ground-Water Quality Data in the Coastal Los Angeles Basin Study Unit, 2006: Results from the California GAMA Program

    Science.gov (United States)

    Mathany, Timothy M.; Land, Michael; Belitz, Kenneth

    2008-01-01

    Ground-water quality in the approximately 860 square-mile Coastal Los Angeles Basin study unit (CLAB) was investigated from June to November of 2006 as part of the Statewide Basin Assessment Project of the Ground-Water Ambient Monitoring and Assessment (GAMA) Program. The GAMA Statewide Basin Assessment was developed in response to the Ground-Water Quality Monitoring Act of 2001, and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The Coastal Los Angeles Basin study was designed to provide a spatially unbiased assessment of raw ground-water quality within CLAB, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 69 wells in Los Angeles and Orange Counties. Fifty-five of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study area (?grid wells?). Fourteen additional wells were selected to evaluate changes in ground-water chemistry or to gain a greater understanding of the ground-water quality within a specific portion of the Coastal Los Angeles Basin study unit ('understanding wells'). Ground-water samples were analyzed for: a large number of synthetic organic constituents [volatile organic compounds (VOCs), gasoline oxygenates and their degradates, pesticides, polar pesticides, and pesticide degradates, pharmaceutical compounds, and potential wastewater-indicators]; constituents of special interest [perchlorate, N-nitrosodimethylamine (NDMA), 1,4-dioxane, and 1,2,3-trichloropropane (1,2,3-TCP)]; inorganic constituents that can occur naturally [nutrients, major and minor ions, and trace elements]; radioactive constituents [gross-alpha and gross-beta radiation, radium isotopes, and radon-222]; and microbial indicators. Naturally occurring isotopes [stable isotopic ratios of hydrogen and oxygen, and activities of tritium and carbon-14

  14. SYNTHESIS AND PHYSICAL-CHEMICAL PROPERTIES OF WATER-SOLUBLE 3-BENZYLXANTHINE DERIVATIVES

    Directory of Open Access Journals (Sweden)

    K. V. Аleksandrova

    2015-04-01

    of water-soluble salts of 3-benzyl-8-methylxanthine. Reflux of 3-benzyl-8-methylxanthine 1 with sodium hydrooxide or ammonium hydroxide in the aqueous solution and ethanolamine, diaethylamine or morpholine in the aqueous propanol-2 led to formation of 3-benzyl-8-methylxanthinides-7 2a-e. The next stage of our study was synthesis of 3-benzyl-8-methylxanthinyl-7-acetic acid 3 with the next obtaining of acetates 5a-h. Acid 3 were synthesized by direct interaction of 3-benzyl-8-methylxanthine 1 or xanthinides-7 2a-e with chloroacetic acid and by hydrolysis of its amide 4 or propyl ester 6. Water-soluble 3-benzyl-8-methylxanthinyl-7-acetates 5а-h were obtained by heating acid 3 with primary, secondary and tertiary amines and ammonium in aqueous or aqueous-alcohol solutions. We also developed alternative method of synthesis of propyl 3-benzyl-8-methylxanthinyl-7-acetate 6, by reflux of acid 3 in propanol-1 with catalytic quantity of dioxane and sulfuric acid. Conclusions Methodic of synthesis of novel water-soluble 3-benzyl-8-methylxanthinides-7 has been developed by interaction of 3-benzyl-8-methylxanthine with bases in aqueous or aqueous alcohol solution. We developed universal method of obtaining of 3-benzyl-8-methylxanthilnyl-7-acetic acid, its amide and water-soluble salts. On example of 3-benzyl-8-methylxanthinyl-7-acetic acid we proposed alternative method of synthesis of alkyl esters – convenient objects for next chemical modification. Structure and identity of all synthesized compounds has been proved by elemental analysis, IR-, 1Н NMR-spectroscopy data and by thin layer chromatography.

  15. Groundwater-Quality Data in the Colorado River Study Unit, 2007: Results from the California GAMA Program

    Science.gov (United States)

    Goldrath, Dara A.; Wright, Michael T.; Belitz, Kenneth

    2010-01-01

    Groundwater quality in the 188-square-mile Colorado River Study unit (COLOR) was investigated October through December 2007 as part of the Priority Basin Project of the California State Water Resources Control Board (SWRCB) Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin Project was developed in response to the Groundwater Quality Monitoring Act of 2001, and the U.S. Geological Survey (USGS) is the technical project lead. The Colorado River study was designed to provide a spatially unbiased assessment of the quality of raw groundwater used for public water supplies within COLOR, and to facilitate statistically consistent comparisons of groundwater quality throughout California. Samples were collected from 28 wells in three study areas in San Bernardino, Riverside, and Imperial Counties. Twenty wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the Study unit; these wells are termed 'grid wells'. Eight additional wells were selected to evaluate specific water-quality issues in the study area; these wells are termed `understanding wells.' The groundwater samples were analyzed for organic constituents (volatile organic compounds [VOC], gasoline oxygenates and degradates, pesticides and pesticide degradates, pharmaceutical compounds), constituents of special interest (perchlorate, 1,4-dioxane, and 1,2,3-trichlorpropane [1,2,3-TCP]), naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), and radioactive constituents. Concentrations of naturally occurring isotopes (tritium, carbon-14, and stable isotopes of hydrogen and oxygen in water), and dissolved noble gases also were measured to help identify the sources and ages of the sampled groundwater. In total, approximately 220 constituents and water-quality indicators were investigated. Quality-control samples (blanks, replicates, and matrix spikes) were collected at

  16. SYNTHESIS AND ANTIMICROBIAL PROPERTIES OF 8-BENZYLIDENHYDRAZINO-1-n-PROPYLTHEOBROMINES

    Directory of Open Access Journals (Sweden)

    D. G. Ivanchenko

    2015-04-01

    cube, NMR-spectra have been taken on a spectrometer Bruker SF-200 (operating frequency of 200 MHz, solvent DMSO, internal standard – TMS. These data correspond to thecalculated elemental analysis.For the initial screening study of the new synthesized substances there has been usedthebenchmarkscultureasgram-positiveandgram-negativebacteriawhich belongtodifferentmorphologicalpropertiesofclinicallyimportantgroupsof infectiousagents.AsasetofstandardteststrainswehavetakenEscherichiacoli ATSS 25922, Staphylococcus aureus ATSS 25923, Pseudomonas aeruginosa ATSS27853, Candida albicans ATSS 885-653. All test strains have been obtained from thelaboratorycalled"ZaporizhzhyaRegionalLaboratoryCenteroftheState epidemiological station of Ukraine." The sensitivity of microorganisms to promising antimicrobialnewsynthesizedsubstanceshasbeendeterminedaccordingtothe guidelines.Duringthestudiestherehavebeenpreparedtheserialtwo-fold dilutions of the drug in Mueller-Hinton broth in a volume of 1 ml, and then added to each tube 0.1 ml of microbial curtain (106 CFU / ml. We havedeterminedtheminimuminhibitoryconcentration(MIC.Asthe solvent compounds we have used dimethylsulfoxidein the studies, the initial solution hasbeenadjustedtoaconcentrationof1mg/ml.Additionallywehaveheldthe control of culture media and solvent by the conventional methods. Results Heating of 8-bromo-1-n-propyltheobromine with an excess of hydrazine hydrate in aqueous dioxane leads to the formation of 8-hydrazino-1-n-propyltheobromine. Interaction of 8-hydrazinoptheobromine with aldehydes has lead to formation of a range of respective 8-benzylidenhydrazinoderivatives. Structure of synthesized compounds has been definitely proved by NMR-spectroscopy.It has beenfound, that synthesized 8-benzylidenhydrazino-1-n-propyltheobrominesexhibit mild effect.Index of antibacterial activity of some compoundsagainstStaphylococcus aureus and Candida albicans is approaching toAmpicillin andNystatin. Conclusion Suggesting laboratory method

  17. Espectros de duas formas de lignina obtidos por ressonância magnética nuclear Nuclear magnetic resonance spectra of two types of lignin

    Directory of Open Access Journals (Sweden)

    Romualdo Shigueo Fukushima

    2003-04-01

    Full Text Available O conteúdo de lignina pode ser útil na estimativa da digestão da fibra de plantas forrageiras. A determinação quantitativa da lignina pelo método espectrofotométrico pressupõe a existência de um padrão de referência satisfatório. O objetivo deste trabalho foi avaliar, por meio da ressonância magnética nuclear (RMN, duas ligninas, uma extraída com brometo de acetila (LBrAc e outra com solução ácida de dioxano (LDiox, para utilização como padrão de referência em análises espectrofotométricas. A ressonância de próton acusou altos teores de carboidratos contaminantes nas amostras de LBrAc. Como a cromatografia líquida já havia indicado menor presença de carboidratos contaminantes na LDiox, os espectros por ressonância de carbono, mais rica em detalhes do que a espectroscopia anterior, porém mais demorada, foram realizados somente nas ligninas LDiox. Este espectro revelou picos típicos, comuns à maioria das ligninas. Os achados da RMN foram condizentes com a análise química, a qual identificou que o carboidrato da parede celular que acompanha a LBrAc seria possivelmente a celulose, ao passo que a pequena contaminação da LDiox teria origem nas pentosanas. A LDiox pode ser considerada melhor padrão de referência para as análises espectrofotométricas do que a LBrAc.Lignin content can be useful to estimate fiber digestion of forage plants. Quantitative determination of lignin by the spectrophotometric method presumes an efficient standard. The objective of this work was to evaluate, by the nuclear magnetic resonance (NMR, two lignins, one extracted with acetyl bromide (AcBrL and another with acidic dioxane solution (DL, as standards in spectrophotometric analysis. Proton resonance revealed high presence of carbohydrates in the AcBrL residues. Because liquid chromatograph had already shown low contamination with carbohydrates in the DL samples, only carbon resonance, which is lengthier, but richer in details than

  18. One barbiturate and two solvated thiobarbiturates containing the triply hydrogen-bonded ADA/DAD synthon, plus one ansolvate and three solvates of their coformer 2,4-diaminopyrimidine.

    Science.gov (United States)

    Hützler, Wilhelm Maximilian; Egert, Ernst; Bolte, Michael

    2016-09-01

    A path to new synthons for application in crystal engineering is the replacement of a strong hydrogen-bond acceptor, like a C=O group, with a weaker acceptor, like a C=S group, in doubly or triply hydrogen-bonded synthons. For instance, if the C=O group at the 2-position of barbituric acid is changed into a C=S group, 2-thiobarbituric acid is obtained. Each of the compounds comprises two ADA hydrogen-bonding sites (D = donor and A = acceptor). We report the results of cocrystallization experiments of barbituric acid and 2-thiobarbituric acid, respectively, with 2,4-diaminopyrimidine, which contains a complementary DAD hydrogen-bonding site and is therefore capable of forming an ADA/DAD synthon with barbituric acid and 2-thiobarbituric acid. In addition, pure 2,4-diaminopyrimidine was crystallized in order to study its preferred hydrogen-bonding motifs. The experiments yielded one ansolvate of 2,4-diaminopyrimidine (pyrimidine-2,4-diamine, DAPY), C4H6N4, (I), three solvates of DAPY, namely 2,4-diaminopyrimidine-1,4-dioxane (2/1), 2C4H6N4·C4H8O2, (II), 2,4-diaminopyrimidine-N,N-dimethylacetamide (1/1), C4H6N4·C4H9NO, (III), and 2,4-diaminopyrimidine-1-methylpyrrolidin-2-one (1/1), C4H6N4·C5H9NO, (IV), one salt of barbituric acid, viz. 2,4-diaminopyrimidinium barbiturate (barbiturate is 2,4,6-trioxopyrimidin-5-ide), C4H7N4(+)·C4H3N2O3(-), (V), and two solvated salts of 2-thiobarbituric acid, viz. 2,4-diaminopyrimidinium 2-thiobarbiturate-N,N-dimethylformamide (1/2) (2-thiobarbiturate is 4,6-dioxo-2-sulfanylidenepyrimidin-5-ide), C4H7N4(+)·C4H3N2O2S(-)·2C3H7NO, (VI), and 2,4-diaminopyrimidinium 2-thiobarbiturate-N,N-dimethylacetamide (1/2), C4H7N4(+)·C4H3N2O2S(-)·2C4H9NO, (VII). The ADA/DAD synthon was succesfully formed in the salt of barbituric acid, i.e. (V), as well as in the salts of 2-thiobarbituric acid, i.e. (VI) and (VII). In the crystal structures of 2,4-diaminopyrimidine, i.e. (I)-(IV), R2(2)(8) N-H...N hydrogen-bond motifs are preferred and, in two

  19. Chemical Modification and Structure-property Relationships of Acrylic and Ionomeric Thermoplastic Elastomer Gels

    Science.gov (United States)

    Vargantwar, Pruthesh Hariharrao

    of EAPs. The unique copolymer investigated here (i) retains its mechanical integrity when highly solvated by polar solvents, (ii) demonstrates a high degree of actuation when tested in a cantilever configuration, and (iii) avoids the shortcomings of back-relaxation/overshoot within the testing conditions when used in combination with an appropriate solvent. In the second part of this work, two chemical strategies to design midblock sulfonated block ionomers are explored. In one case, selective sulfonation of the midblocks in triblock copolymers is achieved via a dioxane:sulfur trioxide chemistry, while in the other acetyl sulfate is used for the same purpose. Excellent control on the degree of sulfonation (DOS) is achieved. The block ionomers swell in different solvents while retaining their mechanical integrity. They show disorder-order, order-order, and order-reduced order morphological transitions as DOS varies. These transitions in morphologies are reflected in their thermal behavior as well. The microstructures show periodicity, which is, again, a function of DOS. The transitions are explained in terms of the molar volume expansion and volume densification of the blocks on sulfonation. The ionic levels, morphology and periodicity in microstructure are important for applications such as actuators, sensors and fuel cell membranes. The ability to tune these aspects in the ionomers designed in this work make them potential candidates for these applications.

  20. Recent Advances in Low-Level Scintillation Counting of Tritium; Progres recents dans le comptage a scintillations de faibles teneurs en tritium; Poslednie dostizheniya v oblasti stsintillyatsionnogo scheta tritiya nizkogo urovnya; Progresos recientes en el recuento por centelleo de bajas concentraciones de tritio

    Energy Technology Data Exchange (ETDEWEB)

    Kaufman, W J; Nir, A; Parks, G; Hours, R M [University of California, Berkeley, CA (United States)

    1962-01-15

    Studies have been made of the liquid scintillation counting system with the objective of optimizing detection sensitivity as expressed by a function of sample volume, efficiency and background. The investigation included a review of scintillator composition. A dioxane-naphthalene-water system having a water content of 18.6% was selected as the most satisfactory composition. Further studies of counting cell geometry and scintillator volume have led to the use of a cylindrical container of 'Teflon' with high gain quartz face photomultipliers in direct contact with the solution. This system gave a tritium detection sensitivity corresponding to a concentration of 0.55 x 10{sup -12} c/ml at an efficiency of 6.9% and a background of 52 cpm. A water sample volume of 31.6 ml was used with total scintillator volume of 170 ml. An internal Co{sup 57} source was found to be a suitable monitor of tritium-counting efficiency in the range 2 to 7% with a standard deviation of 0.1%. It has the advantage over previous methods in that it provided a rapid efficiency determination without modification of the sample. Studies of background reduction were made to evaluate the contribution of luminous interaction and cosmic radiation. A plastic envelope anticoincidence shield was used in the study. Long term effects on stability of the system caused by sample deterioration and counting equipment drifts were evaluated. (author) [French] Les auteurs ont etudie un dispositif de comptage a scintillateur liquide, en vue de rendre optimum la sensibilite de la detection, definie en fonction du volume de l'echantillon, du rendement de comptage et du bruit de fond. Les recherches ont porte notamment sur la composition du scintillateur. On a choisi un melange dioxane-naphthalene-eau, dans lequel cette derniere entrait pour 18,6%, parce que sa composition s'est revelee la plus satisfaisante. D'autres etudes, qui portaient sur la geometrie de la cellule de comptage et le volume du scintillateur, ont

  1. Ground-Water Quality Data in the San Fernando-San Gabriel Study Unit, 2005 - Results from the California GAMA Program

    Science.gov (United States)

    Land, Michael; Belitz, Kenneth

    2008-01-01

    Ground-water quality in the approximately 460 square mile San Fernando-San Gabriel study unit (SFSG) was investigated between May and July 2005 as part of the Priority Basin Assessment Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin Assessment Project was developed in response to the Groundwater Quality Monitoring Act of 2001 and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The San Fernando-San Gabriel study was designed to provide a spatially unbiased assessment of raw ground-water quality within SFSG, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 52 wells in Los Angeles County. Thirty-five of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study area (grid wells), and seventeen wells were selected to aid in the evaluation of specific water-quality issues or changes in water chemistry along a historic ground-water flow path (understanding wells). The ground-water samples were analyzed for a large number of synthetic organic constituents [volatile organic compounds (VOCs), pesticides and pesticide degradates], constituents of special interest [perchlorate, N-nitrosodimethylamine (NDMA), 1,2,3-trichloropropane (1,2,3-TCP), and 1,4-dioxane], naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), radioactive constituents, and microbial indicators. Naturally occurring isotopes (tritium, and carbon-14, and stable isotopes of hydrogen, oxygen, and carbon), and dissolved noble gases also were measured to help identify the source and age of the sampled ground water. Quality-control samples (blanks, replicates, samples for matrix spikes) were collected at approximately one-fifth (11 of 52) of the wells, and the results for these

  2. A Development of Rapid, Practical and Selective Process for Preparation of Z-Oximes

    International Nuclear Information System (INIS)

    Kim, Bo Ram; Sung, Gi Hyeon; Yoon, Yongjin; Kim, Jeumjong

    2013-01-01

    hydrochloride in the presence of potassium carbonate in refluxing 1,4-dioxane to afford the corresponding ketoxime 2a in excellent yield. Acetophenone oxime (2a) was also obtained by the use of ethanol or methanol as the solvent at room temperature or at reflux temperature in excellent yields (Entries 9-12 in Table 1), whereas the side reaction was detected for the reaction of 1a with hydroxylamine hydrochloride in the presence of potassium carbonate in refluxing water. According to our preliminary results, we selected the methanol as the solvent due to short reaction time and low price. As shown in Table 2, aliphatic and aromatic ketones except for benzophenone (1f) were rapidly and selectively converted to the corresponding Z-oximes in good yields. Also, various types of aromatic aldehydes 1g. with electron donating and withdrawing groups were rapidly and selectively converted to the corresponding Zaldoximes in good to excellent yields. In our condition, the oximation of aldehydes is more Z-selective than the oximation of ketones. In order to evaluate the utility of industrial process, we examined the one mole scale reaction. Treatment of one mole acetophenone (1a) and benzaldehyde (1g) with hydroxylamine hydrochloride and potassium carbonate in methanol afforded the corresponding oximes 2a (E/Z ratio = 15:85, 92%) and 2g (E/Z ratio = 10:90, 92%). The structures of the oximes were established by IR and NMR. In the case of ketoximes, we distinguished two isomers by using the carbon chemical shifts of C=NOH, that is, the chemical shifts of the Z-isomer are detected higher field than the chemical shifts of the E-isomer. In the case of aldoximes, E/Z-isomers were distinguished by using the proton chemical shifts of HC=N for aldoximes, that is, the proton chemical shifts of the Z-isomer are detected lower field than the chemical shifts of the E-isomer. In summury, we have demonstrated the rapid and convenient oximation of ketones and aldehydes with potassium carbonate in methanol

  3. A Development of Rapid, Practical and Selective Process for Preparation of Z-Oximes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Bo Ram; Sung, Gi Hyeon; Yoon, Yongjin [Gyeongsang National Univ., Jinju (Korea, Republic of); Kim, Jeumjong [Electronic and Telecommunications Research Institute, Daejeon (Korea, Republic of)

    2013-04-15

    Table 1, compound 1a was treated with hydroxylamine hydrochloride in the presence of potassium carbonate in refluxing 1,4-dioxane to afford the corresponding ketoxime 2a in excellent yield. Acetophenone oxime (2a) was also obtained by the use of ethanol or methanol as the solvent at room temperature or at reflux temperature in excellent yields (Entries 9-12 in Table 1), whereas the side reaction was detected for the reaction of 1a with hydroxylamine hydrochloride in the presence of potassium carbonate in refluxing water. According to our preliminary results, we selected the methanol as the solvent due to short reaction time and low price. As shown in Table 2, aliphatic and aromatic ketones except for benzophenone (1f) were rapidly and selectively converted to the corresponding Z-oximes in good yields. Also, various types of aromatic aldehydes 1g. with electron donating and withdrawing groups were rapidly and selectively converted to the corresponding Zaldoximes in good to excellent yields. In our condition, the oximation of aldehydes is more Z-selective than the oximation of ketones. In order to evaluate the utility of industrial process, we examined the one mole scale reaction. Treatment of one mole acetophenone (1a) and benzaldehyde (1g) with hydroxylamine hydrochloride and potassium carbonate in methanol afforded the corresponding oximes 2a (E/Z ratio = 15:85, 92%) and 2g (E/Z ratio = 10:90, 92%). The structures of the oximes were established by IR and NMR. In the case of ketoximes, we distinguished two isomers by using the carbon chemical shifts of C=NOH, that is, the chemical shifts of the Z-isomer are detected higher field than the chemical shifts of the E-isomer. In the case of aldoximes, E/Z-isomers were distinguished by using the proton chemical shifts of HC=N for aldoximes, that is, the proton chemical shifts of the Z-isomer are detected lower field than the chemical shifts of the E-isomer. In summury, we have demonstrated the rapid and convenient oximation of

  4. Synthesis, characterization, and properties of peroxo-based oxygen-rich compounds for potential use as greener high energy density materials

    Science.gov (United States)

    Gamage, Nipuni-Dhanesha Horadugoda

    HEDMs. Oxygen-rich (0.80--1.00) geminal hydroperoxides have detonation velocities in the range of 6150--7130 m/s. These impressive detonation velocities are greater than the detonation velocities of the known peroxo-based explosives. The highest detonation velocity (7130 m/s) was obtained for 1,4-bis(dihydroperoxymethyl)benzene, which has the highest crystalline density (1.648 g/cm3). This detonation velocity is greater than the secondary explosive 2,4,6-trinitrotoluene (TNT). The sensitivities of these oxygen-rich geminal hydroperoxides are lower than the known peroxo-based explosives due to the O--H•••O hydrogen bonds and O•••O contacts, which stabilize the weak O--O bonds in the crystalline lattice. They could be useful as primary HEDMs. Dihydroperoxy dioxane and dioxolanes have impressive detonation velocities in the range of 6350--6694 m/s. However, their extremely high sensitivities render them unsafe for HEDM applications. Interestingly, hydroperoxy dioxanol and dioxolanols also have high detonation velocities in the range of 6100--6461 m/s even with the lower oxygen contents. The hydroperoxy compounds with one less O--O bond were much less sensitive than the dihydroperoxy compounds. These hydroperoxy compounds could be useful as primary HEDMs. We observed that the ring strain was useful in increasing the detonation velocities, since it led to compounds with higher crystalline densities. However, increasing the steric strain using bulky groups led to lower crystalline densities and lower detonation velocities. Higher steric strain not only resulted in higher sensitivities but also lower thermal stabilities. Peroxy acids have high detonation velocities in the range of 5262--7885 m/s. The detonation velocity of 3,5-dinitrobenzoperoxoic acid (7217 m/s) was the highest detonation velocity obtained for the peroxo-based compounds synthesized in our study, which is greater than the detonation velocity of TNT. The detonation velocity of 2

  5. Coupling of Plasmas and Liquids

    Science.gov (United States)

    Lindsay, Alexander David

    the design and characterization of our plasma-liquid systems, we illustrate their applications to plant fertilization and wastewater disinfection. In a four-week collaborative experiment with the NCSU greenhouse, plants that received plasma-treated water grew significantly larger than plants that received tap water. This is directly attributable to the approximately hundred mg/L of NO-3 dissolved into solution by the plasma. The VHF source also proved effective at removing several aqueous contaminants designated harmful to humans by the EPA. Air plasma treatment of solutions contaminated with 1,4-dioxane showed log reduction times competitive with other advanced oxidative processes (AOP). Argon treatment of dixoane was an order of magnitude more effective in terms of log reduction time, although the associated costs are significantly higher. Perfluorooctanesulfonic acid (PFOS) proved resistant to several VHF design iterations. However, the water electrode design introduced in the passage above achieved a log reduction in low level PFOS concentrations over the course of twenty five minutes, suggesting that it may be viable as an advanced technology for degradation of persistent perfluorinated compounds. (Abstract shortened by ProQuest.).