Dissolution of Platinum in Hydrochloric Acid Under Industrial-Scale Alternating Current Polarization

Science.gov (United States)

Myrzabekov, B. E.; Bayeshov, A. B.; Makhanbetov, A. B.; Mishra, B.; Baigenzhenov, O. S.

2018-02-01

The electrochemical behavior of platinum in a hydrochloric acid solution under polarization by an industrial-scale alternating current has been investigated. For the electrical dissolution of platinum, titanium is used as an auxiliary electrode, which increases the yield of platinum dissolution by 12.5 pct. The influence of the concentration of hydrochloric acid, the current densities of the platinum and titanium electrodes, and the temperature of the electrolyte on the efficiency of the process of dissolving platinum have all been studied.

Corrosion inhibitors for aluminium in hydrochloric acid. Vanilline on aluminium 2S, 57S and 65S

Energy Technology Data Exchange (ETDEWEB)

Desai, M.N.

1972-12-01

So far, the only aldehyde reported in literature for the inhibition of the corrosion of aluminum in hydrochloric acid, is furfuraldehyde. This study reports vanilline as a corrosion inhibitor for aluminum alloys 2S, 57S, and 65S. These specifications for the alloys are listed. The influence of inhibitor concentration and time on inhibitor efficiency is given in tabular data and illustrated graphically. The corrosion of aluminum alloys 2S, 57S, and 65S increases with time and hydrochloric acid concentration. Polarization measurements indicate that the corrosion of aluminum alloys in hydrochloric acid is cathodically controlled. The behavior of vanilline as a corrosion inhibitor is very interesting. In 2.0N solution of hydrochloric acid, vanilline affords nearly complete protection (97 to 99%) to all the 3 aluminum alloys investigated up to 60 min. However, in 1.0N solutions of hydrochloric acid, the corrosion of aluminum 2S is severely accelerated by vanilline.

Decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid

International Nuclear Information System (INIS)

Mamatov, E.D.; Khomidi, A.K.

2015-01-01

Present article is devoted to decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminosilicate ores were studied by means of X-ray phase, differential-thermal analysis methods. The chemical and mineral composition of aluminosilicate ores was considered. The kinetics of acid decomposition of aluminosilicate ores composed of two stages was studied as well. The flowsheets of complex processing of aluminium comprising ores by means of chloric and acid methods were proposed.

Leachability of nitrided ilmenite in hydrochloric acid

OpenAIRE

Swanepoel, J.J.; van Vuuren, D.S.; Heydenrych, M.

2011-01-01

Titanium nitride in upgraded nitrided ilmenite (bulk of iron removed) can selectively be chlorinated to produce titanium tetrachloride. Except for iron, most other components present during this low temperature (ca. 200°C) chlorination reaction will not react with chlorine. It is therefore necessary to remove as much iron as possible from the nitrided ilmenite. Hydrochloric acid leaching is a possible process route to remove metallic iron from nitrided ilmenite without excessive dissolution o...

1.6. The kinetics of hydrochloric acid decomposition of argillite of Chashma-Sang Deposit

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Mirzoev, D.Kh.; Boboev, Kh.E.

2016-01-01

Present article of book is devoted to kinetics of hydrochloric acid decomposition of argillite of Chashma-Sang Deposit. It was defined that with temperature increasing the extraction rate of Al_2O_3 and Fe_2O_3 increases. The dependence of extraction rate of Al_2O_3 and Fe_2O_3 on process duration at hydrochloric acid decomposition of argillite was studied. The activation energy of the process was defined.

On-line Determination of Hydrochloric Acid in Process Effluent ...

African Journals Online (AJOL)

Prof Van Staden

The sample is sandwiched between two titrants in a holding coil, with the volume of the first base being twice to that of the second one and channeled by flow reversal through a reaction coil to the potentiometric sensor. A linear relationship between peak width and logarithm of the hydrochloric acid concentration was.

Nontoxic corrosion inhibitors for N80 steel in hydrochloric acid

Directory of Open Access Journals (Sweden)

M. Yadav

2016-11-01

Full Text Available The purpose of this paper is to evaluate the protective ability of 1-(2-aminoethyl-2-oleylimidazoline (AEOI and 1-(2-oleylamidoethyl-2-oleylimidazoline (OAEOI as corrosion inhibitors for N80 steel in 15% hydrochloric acid, which may find application as eco-friendly corrosion inhibitors in acidizing processes in petroleum industry. Different concentrations of synthesized inhibitors AEOI and OAEOI were added to the test solution (15% HCl and the corrosion inhibition of N80 steel in hydrochloric acid medium containing inhibitors was tested by weight loss, potentiodynamic polarization and AC impedance measurements. Influence of temperature (298–323 K on the inhibition behavior was studied. Surface studies were performed by using FTIR spectra and SEM. Both the inhibitors, AEOI and OAEOI at 150 ppm concentration show maximum efficiency 90.26% and 96.23%, respectively at 298 K in 15% HCl solution. Both the inhibitors act as mixed corrosion inhibitors. The adsorption of the corrosion inhibitors at the surface of N80 steel is the root cause of corrosion inhibition.

Heavy metal recovery from electric arc furnace steel slag by using hydrochloric acid leaching

Science.gov (United States)

Wei, Lim Jin; Haan, Ong Teng; Shean Yaw, Thomas Choong; Chuah Abdullah, Luqman; Razak, Mus'ab Abdul; Cionita, Tezara; Toudehdehghan, Abdolreza

2018-03-01

Electric Arc Furnace steel slag (EAFS) is the waste produced in steelmaking industry. Environmental problem such as pollution will occur when dumping the steel slag waste into the landfill. These steel slags have properties that are suitable for various applications such as water treatment and wastewater. The objective of this study is to develop efficient and economical chlorination route for EAFS extraction by using leaching process. Various parameters such as concentration of hydrochloric acid, particle size of steel slag, reaction time and reaction temperature are investigated to determine the optimum conditions. As a result, the dissolution rate can be determined by changing the parameters, such as concentration of hydrochloric acid, particle size of steel slag, reaction time and reaction temperature. The optimum conditions for dissolution rates for the leaching process is at 3.0 M hydrochloric acid, particle size of 1.18 mm, reaction time of 2.5 hour and the temperature of 90°C.

Separation of molybdenum(VI) by extraction with n-octylaniline from hydrochloric acid medium

International Nuclear Information System (INIS)

Sawant, S.S.; Anuse, M.A.; Chavan, M.B.

1997-01-01

N-Octylaniline in benzene was used for the extractive separation of molybdenum(VI) from hydrochloric acid medium. Molybdenum(VI) was extracted quantitatively from 10 ml aqueous solution 1.5M in hydrochloric acid and 10M in lithium chloride into 10 ml of 10% n-octylaniline in benzene. It was stripped from the organic phase with 5% aqueous ammonia solution and estimated spectrophotometrically with thiocyanate at 465 nm. The interference of various ions has been studied in detail and conditions have been established for the determination of molybdenum(VI) in synthetic mixtures and alloy samples. (author)

Potential for the use of hydrochloric acid in fission reactor fuel recycle

International Nuclear Information System (INIS)

Mailen, J.C.; Bell, J.T.

1985-01-01

The chemistry and the effects of the use of hydrochloric acid as the aqueous phase in fuel recycle are surveyed. Available data are sufficient to suggest that separations of actinides and fission products can be at least as good in an HCl-trialkyl amine system as in Purex. Advantages of the HCl system are simpler operations of the off-gas system, better separation of neptunium from uranium and plutonium, better control of oxidation states of the dissolved species, and simpler recycle of the acid. A possible advantage is the more complete dissolution of the fission products, leaving very little insoluble residue. Disadvantages include lack of development of methods for dissolution of oxide fuel in hydrochloric acid, the requirement for processing equipment constructed of titanium, possible complications in the waste-handling system, and the dissolution of much of the cladding in the case of stainless-steel clad fuel

Polarography of niobium in hydrochloric acid

International Nuclear Information System (INIS)

Henrion, G.; Adler, F.; Andreas, B.

1978-01-01

Dependence between the limiting current and the concentration of niobium and hydrochloric acid has been investigated. With the decrease of niobium concentration the hydrolysis and condensation reactions proceed slower. The time dependence of condensation is shown using ethylene glycol which delays the condensation because of complexation of Nb(5). Hydroxylamine hydrochloride increases the limiting current by a kinetic effect by one order of magnitude which was observed clearly by cyclic voltammetry. Even small amounts of ethylene glycol suppress the kinetic effect. Polarographic determination of niobium in HCl as a supporting electrolyte is possible in concentration above 10 M only. Addition of ethylene glycol and hydroxylamine hydrochloride enables determination of small amounts of niobium in 4 M HCl. (author)

Nontoxic corrosion inhibitors for N80 steel in hydrochloric acid

OpenAIRE

M. Yadav; Debasis Behera; Usha Sharma

2016-01-01

The purpose of this paper is to evaluate the protective ability of 1-(2-aminoethyl)-2-oleylimidazoline (AEOI) and 1-(2-oleylamidoethyl)-2-oleylimidazoline (OAEOI) as corrosion inhibitors for N80 steel in 15% hydrochloric acid, which may find application as eco-friendly corrosion inhibitors in acidizing processes in petroleum industry. Different concentrations of synthesized inhibitors AEOI and OAEOI were added to the test solution (15% HCl) and the corrosion inhibition of N80 steel in hydroch...

Kinetics of the Leaching Process of an Australian Gibbsitic Bauxite by Hydrochloric Acid

Directory of Open Access Journals (Sweden)

Aichun Zhao

2016-01-01

Full Text Available Gibbsitic bauxite from Australia was leached by hydrochloric acid in this work. Analysis on kinetics for the extraction of Al2O3 was quantitatively studied. It was concluded that the hydrochloric acid leaching process of gibbsitic bauxite was controlled by chemical reaction. Moreover, the mechanism for the dissolution followed the equation, ln⁡k=39.44-1.66×104(1/T, with an apparent activation energy of 137.90 kJ/mol, according to the equation of k=Ae-Ea/RT. This work aims to provide a good theory support for the process control by using a new method of alumina production from the low grade bauxite.

The role of octanol in the extraction of hydrochloric acid by trilaurylamine dissolved in benzene

International Nuclear Information System (INIS)

Muhammed, M.A.

1976-01-01

The extraction of hydrochloric acid by trilaurylamine (TLA) dissolved in benzene was studied in the presence and in absence of n-octanol. The extraction of HCl was found to be enhanced by the addition of octanol to the organic phase. In order to explain this effect by means of the law of mass action, the systems TLA-HCl-benzene and n-octanol-HCl-benzene as well as TLA-octanol-benzene were also studied. It was found that TLA reacts with octanol to form a complex TLAROH, while the octanol itself associates in benzene to form dimers and tetramers, although it does not extract HCl alone from the dilute solutions used in the present study. The enhancement of the extraction of HCl by TLA upon the addition of n-octanol could be described by the formation of the species TLA.ROH.HCl and its stability constant was determined. (author)

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution

International Nuclear Information System (INIS)

Liu, Hu; Zhang, Shengen; Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin; Volinsky, Alex A.

2014-01-01

Highlights: • The article provides a new method for recycling rare earth (RE) from waste phosphor. • When compared with the traditional methods, leach rate was much higher. • Y–Eu concentrate and Tb–Ce concentrate were obtained successively. • It would reduce the burden of later extraction, separation and purification. - Abstract: This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y 0.95 Eu 0.05 ) 2 O 3 in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce 0.67 Tb 0.33 MgAl 11 O 19 ) and the Blue phosphor (Ba 0.9 Eu 0.1 MgAl 10 O 17 ) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO 2 are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications

Determination of sulfur in steels by isotope dilution mass spectrometry after dissolution with sealed tube

International Nuclear Information System (INIS)

Watanabe, Kazuo

1981-01-01

The scaled tube dissolution technique was studied for the complete conversion of sulfur in steels to sulfate. Isotope dilution mass spectrometry was used for the determination of sulfur in the sulfate. Sample (0.5 g) was dissolved in nitric acid (7 ml) and hydrochloric acid (3 ml) in a scaled borosilicate glass tube on being heated above 180 0 C overnight. Nitrate ions were removed by repeated evaporation with hydrochloric acid. The residue was dissolved in hydrochloric acid. Sulfate was reduced with a mixture of hydrochloric, hydroiodic and hypophosphorous acids; hydrogen sulfide evolved was absorbed in cadmium acetate solution, then converted to silver sulfide, which was burned to sulfur dioxide in pure oxygen at low pressure, for isotopic analysis. Analytical blank in whole procedure was 0.8 μg of sulfur. This technique was applied to the determination of sulfur in NBS low alloy steels. The principal cause of low values obtained by the open beaker dissolution technique was evaporation losses of sulfur as sulfur dioxide during the dissolution. (author)

Extraction of magnesium from calcined dolomite ore using hydrochloric acid leaching

Science.gov (United States)

Royani, Ahmad; Sulistiyono, Eko; Prasetiyo, Agus Budi; Subagja, Rudi

2018-05-01

Magnesium is widely used in varieties industrial sector. Dolomite is one source of magnesium besides seawater. The extraction of magnesium from dolomite ores can be done by leaching process. In this work, the dolomite leaching to extract magnesium by hydrochloric acid was investigated. The leaching experiments were performed in a spherical glass batch reactor having a capacity of 1000 ml. The effects of the stirring speed, acid concentration, reaction temperature and liquid-solid ratio for each reaction time of 1; 2; and 3 h on the Mg leaching have been evaluated. 5 ml of solution sample were collected from the leached solutions, then it was filtered prior to analysis by ICP OES. The experimental results show that the magnesium extraction increases along with the increase of acid concentration, liquid-solid ratio and temperature. The optimum conditions for magnesium extraction were achieved at temperature 75 °C, extraction time 3 h, the HCl concentration of 2 M, the liquid-solid ratio 20 ml/g and stirring speed of 400 rpm. At this condition 98, 82 % of magnesium were extracted from dolomite. The conclusion obtained from this leaching process is that the magnesium can be extracted from dolomite by using hydrochloric acid solutions.

Adsorption and purification of radiogallium in hydrochloric acid and metal chloride solutions by non-ionic resin of macro-reticular type

International Nuclear Information System (INIS)

Imai, Kiyoko; Watari, Kazuo; Ohno, Shigeru; Ohmiya, Toshinobu; Kuroda, Emi; Izawa, Masami.

1986-01-01

Adsorption behavior of radiogallium ( 67 Ga, 68 Ga) on non-ionic MR resin (XAD-7) from hydrochloric acid, lithium chloride and other metal chloride solutions, and purification of 68 Ga by this resin were studied. Radiogallium was adsorbed on XAD-7 rapidly and quantitatively from the solution of higher chloride concentration than 6M. The adsorption behavior is similar to that obtained with 59 Fe and 195 Au previously. Based on adsorption data, elimination of trace amount of 68 Ge commonly contained in 68 Ga milked from a 68 Ge/ 68 Ga generator was tried. When 68 Ga-6M hydrochloric acid solution containing 68 Ge was passed through a XAD-7 column, all the activity was transferred on the column. After eliminating 68 Ge fraction with 3M hydrochloric acid, 68 Ga was obtained in high purity by eluting with 0.1M hydrochloric acid. (author)

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution

Energy Technology Data Exchange (ETDEWEB)

Liu, Hu [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhang, Shengen, E-mail: zhangshengen@mater.ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Volinsky, Alex A. [Department of Mechanical Engineering, University of South Florida, Tampa, FL 33620 (United States)

2014-05-01

Highlights: • The article provides a new method for recycling rare earth (RE) from waste phosphor. • When compared with the traditional methods, leach rate was much higher. • Y–Eu concentrate and Tb–Ce concentrate were obtained successively. • It would reduce the burden of later extraction, separation and purification. - Abstract: This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y{sub 0.95}Eu{sub 0.05}){sub 2}O{sub 3} in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce{sub 0.67}Tb{sub 0.33}MgAl{sub 11}O{sub 19}) and the Blue phosphor (Ba{sub 0.9}Eu{sub 0.1}MgAl{sub 10}O{sub 17}) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO{sub 2} are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications.

Hydrochloric acid leaching of uranium, thorium, radium and rare-earth elements, from an Elliot lake radioactive ore

International Nuclear Information System (INIS)

Mahdy, M.A.

1988-01-01

Extraction of uranium by commercial methods using sulphuric acid developed a lot of environmental problems. To avoid such problems, other uranium extraction techniques have been adopted including fluorination, chlorination, chlorine assisted leaching, hydrochloric acid leaching, etc. This work is oriented towards the study of the factors controlling the hydrochloric acid leaching. The target of the study is to extract the total amount of U, Th, Ra-226 and rare earth elements. By using a suitable combination of the leaching factors, it was possible to achieve the designed target

Extraction of rare earths and hydrochloric acid by trialkylphosphine oxide

International Nuclear Information System (INIS)

Mikhajlichenko, A.I.; Karmannikov, V.P.; Klimenko, M.A.; Fedulova, T.V.

1983-01-01

Extraction of rare earth chlorides and hydrochloric acid by trialkylphosphine oxide with different radicals (POR) (RR' 2 PO-POR, where RR'=alkyl of a normal structure, containing 7 to 9 carbon atoms, R=isoamyl) has been studied. Distribution of lanthanum-, neodymium-, lutetium- and yttrium chlorides during extraction with 1.28 mol/l POR solution in white spirit is investigated in the salt concentration range in the equilibrium aqueous phase from 0 to 2.8 mol/l. Lanthanide distribution coefficients increase with an increase in the order number of elements, with the separation coefficients of two extreme members of the series (Lu and La) for chlorides and nitrates constituting 100 and 80, respectively microquantities of Ln against the background of macroquantities of La is 2.6 mol/l. According to the results of measurements of viscosity, electric conductivity and water content in the extracts a conclusion is made on the state of salt in the organic phase. In the systems POR-LnCl 3 -HCl-H 2 O the hydrochloric acid extraction increases with an increase in the rare earth chloride concentration and order number of the element

Inhibitive Effect of Butyltin Trichloride on Dissolution and Localized Corrosion of Aluminium in Sodium Hydroxide and Hydrochloric Acid

OpenAIRE

Mourad, M.Y.; Ibrahim, E.H.; Seliman, S.A.

1990-01-01

The dissolution of aluminium in sodium hydroxide and hydrochloric acid in the presence of butyltin trichloride as corrosion inhibitor has been studied by hydrogen evolution and thermometric methods. Experimental findings indicate that the inhibition effect of butyltin trichloride takes place through an adsorption mechanism following the Frumkin's isotherm. Butyltin trichloride acts as a weakly adsorbed inhibitor in NaOH and as a strongly adsorbed inhibitor in hydrochloric acid medium. Wile...

Investigation of rare earths sorption from sulfuric- and hydrochloric media

International Nuclear Information System (INIS)

Nikonov, V.N.; Mikhlin, E.B.; Norina, T.M.; Afonina, T.A.

1978-01-01

A rate of equilibrium attainment has been studied during REE sorption from sulfuric and hydrochloric acid solutions and pulps. It has been shown that equilibrium upon sorption from hydrochloric acid solutions is attained faster than from sulfuric acid solutions. Equilibrium upon sorption from pulps is attained considerably slower than upon sorption from solutions. In all cases REM of cerium subgroup are sorbed better. An effect has been studied of the medium acidity on sorbability of REM and elements of iron and calcium impurities. It has been established that sorbability of these elements decreases with increasing acid concentration. Selectivity of REM sorption from sulfuric acid solutions decreases with a rise in H 2 SO 4 concentration in the solution. For hydrochloric acid solutions it remains constant in a wide range of HCl concentrations. Sorption leaching of REM from concentrates and cakes of sulfuric and hydrochloric acids in the presence of KU-2 leads to high technical and economic indexes: extraction with respect to the total amount of REM and yttrium into a commercial product is 76-86% for sulfuric acid solutions and 81-90% for hydrochloric solutions

Inhibitory effect of some carbazides on corrosion of aluminium in hydrochloric acid and sodium hydroxide solutions

Energy Technology Data Exchange (ETDEWEB)

Fouda, A.S. [El-Mansoura Univ. (Egypt). Dept. of Chemistry; Madkour, L.H. [Tanta Univ. (Egypt). Dept. of Chemistry; Elshafei, A.A. [El-Mansoura Univ. (Egypt). Dept. of Chemistry; Elasklany, A.H. [El-Mansoura Univ. (Egypt). Dept. of Chemistry

1995-06-01

The dissolution of aluminium in hydrochloric acid and sodium hydroxide solutions in the presence of semicarbazide, thiosemicarbazide and sym.diphenylcarbazide as corrosion inhibitors has been studied using thermometric, weight-loss and polarization methods. The three methods gave consistent results. The higher inhibition efficiency of these compounds in acidic than in alkaline madia may be due to the less negative potential of aluminium in hydrochloric acid solution, favouring adsorption of the additive. The adsorption of these compounds were found to obey Frumkin adsorption isotherm. Cathodic polarization measurements showed that these compounds are cathodic inhibitors and their adsorption in the double layer does not change the mechanism of the hydrogen evolution reaction. The results are analysed in terms of both molecular and cationic adsorption. (orig.)

Model Experiment of Thermal Runaway Reactions Using the Aluminum-Hydrochloric Acid Reaction

Science.gov (United States)

Kitabayashi, Suguru; Nakano, Masayoshi; Nishikawa, Kazuyuki; Koga, Nobuyoshi

2016-01-01

A laboratory exercise for the education of students about thermal runaway reactions based on the reaction between aluminum and hydrochloric acid as a model reaction is proposed. In the introductory part of the exercise, the induction period and subsequent thermal runaway behavior are evaluated via a simple observation of hydrogen gas evolution and…

Studies on the solvent extraction behaviour of Pu(IV) from nitric acid, nitric-perchloric acid and hydrochloric acids, by di,2-ethylhexyl phosphoric acid (HDEHP)

International Nuclear Information System (INIS)

Phal, D.G.; Kannan, S.K.; Ramakrishna, V.V.

1994-01-01

Extraction of plutonium (IV) from aqueous nitric acid, nitric-perchloric acid and hydrochloric acids by di,2-ethylhexyl phosphoric acid, the dimeric form of which is represented as H 2 Y 2 , in different diluents (dodecane, toluene and chloroform) was investigated. The composition of the extracted Pu(IV) species were found to be Pu(NO 3 ) 2 (HY) 2 , Pu(NO 3 )(ClO 4 )(HY 2 ) 2 , PuClY(HY 2 ) 2 and PuCl 2 (HY 2 ) 2 from nitric, nitric-perchloric and hydrochloric acids respectively, the last one being pre-dominant at high aqueous acidities (i.e. 5M HCl). Synergic enhancement in the extraction of Pu(IV) from different aqueous media, by the addition of thenoyltrifluoroacetone (HTTA) to HDEHP was also investigated and was attributed to the formation and extraction of the species PuX(TTA)(HY 2 ) 2 , and Pu(TTA) 2 (HY 2 ) 2 where X=Cl - or NO 3 - . The addition of the neutral extractant TOPO to H 2 Y 2 also resulted in synergism. The possible equilibria in these systems were inferred and the corresponding equilibrium constants determined. (author). 24 refs., 10 figs., 10 tabs

Electrochemical studies of novel corrosion inhibitor for mild steel in 1 M hydrochloric acid

Directory of Open Access Journals (Sweden)

Ahmed A. Al-Amiery

2018-06-01

Full Text Available The electrochemical performance of a novel organic corrosion inhibitor 6-(4-hydroxyphenyl-3-mercapto-7,8-dihydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazine [HT3], for mild steel in 1 M hydrochloric acid is evaluated by potentiodynamic curves. The experimental results show that the investigated inhibitor [HT3], which can effectively retard the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing a protective coating for the mild steel that, can be weakened by increasing the temperature. Furthermore, the inhibition efficiency of [HT3] increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. Keywords: Corrosion, Inhibitor, Mild steel, Potentiodynamic polarization, HT3, NMR, FT-IR

Dilute acid/metal salt hydrolysis of lignocellulosics

Science.gov (United States)

Nguyen, Quang A.; Tucker, Melvin P.

2002-01-01

A modified dilute acid method of hydrolyzing the cellulose and hemicellulose in lignocellulosic material under conditions to obtain higher overall fermentable sugar yields than is obtainable using dilute acid alone, comprising: impregnating a lignocellulosic feedstock with a mixture of an amount of aqueous solution of a dilute acid catalyst and a metal salt catalyst sufficient to provide higher overall fermentable sugar yields than is obtainable when hydrolyzing with dilute acid alone; loading the impregnated lignocellulosic feedstock into a reactor and heating for a sufficient period of time to hydrolyze substantially all of the hemicellulose and greater than 45% of the cellulose to water soluble sugars; and recovering the water soluble sugars.

Ginger extract as green corrosion inhibitor of mild steel in hydrochloric acid solution

Science.gov (United States)

Fidrusli, A.; Suryanto; Mahmood, M.

2018-01-01

Ginger extract as corrosion inhibitor from natural resources was studied to prevent corrosion of mild steel in acid media. Ginger rhizome was extracted to produce green corrosion inhibitor (G-1) while ginger powder bought at supermarket was also extract to form green corrosion inhibitor (G-2). Effectiveness of inhibitor in preventing corrosion process of mild steel was studied in 1.0 M of hydrochloric acid. The experiment of weight loss method and polarization technique were conducted to measure corrosion rate and inhibition efficiency of mild steel in solution containing 1.0 M of hydrochloric acid with various concentration of inhibitor at room temperature. The results showed that, the rate of corrosion dropped from 8.09 mmpy in solution containing no inhibitor to 0.72 mmpy in solution containing 150g/l inhibitor while inhibition efficiency up to 91% was obtained. The polarization curve in polarization experiments shows that the inhibition efficiency is 86% with high concentration of inhibitor. The adsorption of ginger extract on the surface of mild steel was observed by using optical microscope and the characterization analysis was done by using pH measurement method. When high concentration of green inhibitor in the acid solution is used, the pH at the surface of steel is increasing.

The criteria of critical runaway and stable temperatures of catalytic decomposition of hydrogen peroxide in the presence of hydrochloric acid

International Nuclear Information System (INIS)

Lu, K.-T.; Yang, C.-C.; Lin, P.-C.

2006-01-01

The hydrogen peroxide and hydrochloric acid are used in close proximity in the computer chip manufacture. The hydrochloric acid catalyzes an exothermic decomposition of hydrogen peroxide into oxygen and water. The accumulation of heat and non-condensable gas increases temperature and pressure in this reaction process always lead to runaway reaction and accident owing to inadvertent mixing. Thus, the chemical reaction hazard has to be clearly identified. Its critical runaway temperatures and unstable reaction criteria in this reaction process have to be determined urgently. In this investigation, we estimated its kinetic parameters at various volumetric ratios of the hydrogen peroxide to hydrochloric acid. Then, used these kinetic parameters to evaluate their critical temperatures and stable criteria in each reaction processes. The analytic results are important and useful for the design of safety system in the computer chip manufacture

Inhibition of the corrosion of mild steel in hydrochloric acid by isatin ...

African Journals Online (AJOL)

The inhibition of corrosion of mild steel in hydrochloric acid by isatin glycine (ING) and isatin (IN) at 30-60 oC and concentrations of 0.0001 M to 0.0005 M was studied via weight loss method. At the highest inhibitor concentration studied ING exhibited inhibition efficiency of 87% while IN exhibited 84% at 60 oC. A chemical ...

The extraction of vanadium (IV) from hydrochloric acid solutions by tricaprylmethylammonium chloride and trioctylamine

International Nuclear Information System (INIS)

Nakamura, Takato; Sato, Taichi

1980-01-01

The extraction of vanadium (IV) from hydrochloric acid solutions by tricaprylmethylammonium chloride (R 3 RNCl, Aliquat-336) and trioctylamine (R 3 N, TOA) in benzene has been investigated under various conditions. In addition, the extraction behaviour of vanadium into the organic phase has been examined by spectrophotometry and electron spin resonance (ESR) spectroscopy. From the distribution data, it is concluded that the extractions of vanadium (IV) from hydrochloric acid solutions by Aliquat-336 and TOA are expressed as VOCl 3 - (aq) + R 3 R'NCl(org) reversible R 3 R'NVOCl 3 (org) + Cl - (aq) and VOCl 2 (aq) + R 3 NHCl(org) reversible R 3 NHVOCl 3 (org) The electronic spectral and ESR results suggest that the complexes, R 3 R'NVOCl 3 and R 3 NH.VOCl 3 , formed in the organic phase are not always stable, but easily hydrolized or oxidized. (author)

Effect of beverages on bovine dental enamel subjected to erosive challenge with hydrochloric acid.

Science.gov (United States)

Amoras, Dinah Ribeiro; Corona, Silmara Aparecida Milori; Rodrigues, Antonio Luiz; Serra, Mônica Campos

2012-01-01

This study evaluated by an in vitro model the effect of beverages on dental enamel previously subjected to erosive challenge with hydrochloric acid. The factor under study was the type of beverage, in five levels: Sprite® Zero Low-calorie Soda Lime (positive control), Parmalat® ultra high temperature (UHT) milk, Ades® Original soymilk, Leão® Ice Tea Zero ready-to-drink low-calorie peach-flavored black teaand Prata® natural mineral water (negative control). Seventy-five bovine enamel specimens were distributed among the five types of beverages (n=15), according to a randomized complete block design. For the formation of erosive wear lesions, the specimens were immersed in 10 mL aqueous solution of hydrochloric acid 0.01 M for 2 min. Subsequently, the specimens were immersed in 20 mL of the beverages for 1 min, twice daily for 2 days at room temperature. In between, the specimens were kept in 20 mL of artificial saliva at 37ºC. The response variable was the quantitative enamel microhardness. ANOVA and Tukey's test showed highly significant differences (penamel exposed to hydrochloric acid and beverages. The soft drink caused a significantly higher decrease in microhardness compared with the other beverages. The black tea caused a significantly higher reduction in microhardness than the mineral water, UHT milk and soymilk, but lower than the soft drink. Among the analyzed beverages, the soft drink and the black tea caused the most deleterious effects on dental enamel microhardness.

2.4. The kinetics of hydrochloric-acid decomposition of calcined concentrate of boron raw material of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

2015-01-01

Present article is devoted to kinetics of hydrochloric-acid decomposition of calcined concentrate of boron raw material of Ak-Arkhar Deposit. The experimental data of dependence of hydrochloric-acid decomposition of calcined boron raw material for boron oxide extraction on temperature (20-80 deg C) and process duration (15-60 min) were considered. It was defined that at temperature increasing the boron oxide extraction from borosilicate raw material increases from 24.1 till 86.8%. The constants of decomposition rate of boron raw material were calculated.

Acid hydrolysis of corn stover using hydrochloric acid: Kinetic modeling and statistical optimization

Directory of Open Access Journals (Sweden)

Sun Yong

2014-01-01

Full Text Available The hydrolysis of corn stover using hydrochloric acid was studied. The kinetic parameters of the mathematical models for predicting the yields of xylose, glucose, furfural and acetic acid were obtained, and the corresponding xylose generation activation energy of 100 kJ/mol was determined. The characterization of corn stover using with different techniques during hydrolysis indicated an effective removal of xylan and the slightly alteration on the structures of cellulose and lignin. A 23five levels Central Composite Design (CCD was used to develop a statistical model for the optimization of process variables including acid concentration, pretreatment temperature and time. The optimum conditions determined by this model were found to be 108ºC for 80 minutes with acid concentration of 5.8%. Under these conditions, the maximised results are the following: xylose 19.93 g/L, glucose 1.2 g/L, furfural 1.5 g/L, acetic acid 1.3 g/L. The validation of the model indicates a good agreement between the experimental results and the predicted values.

The Comparison of Hydrochloric Acid and Phosphoric Acid Treatments in the Preparation of Montmorillonite Catalysts for RNA Synthesis

Science.gov (United States)

Aldersley, Michael Frank; Joshi, Prakash C.; Huang, Yixing

2017-09-01

The treatment of clay minerals with a preliminary acid wash and titration to pH 7 has proven to generate catalysts for the most interesting of oligomerization reactions in which activated RNA-nucleotides generate oligomers up to 40-mers. Significantly, not all clay minerals become catalytic following this treatment and none are catalytic in the absence of such treatment. The washing procedure has been modified and explored further using phosphoric acid and the outcomes are compared to those obtained when clay samples are prepared following a hydrochloric acid wash.

Selection of suitable mineral acid and its concentration for biphasic dilute acid hydrolysis of the sodium dithionite delignified Prosopis juliflora to hydrolyze maximum holocellulose.

Science.gov (United States)

Naseeruddin, Shaik; Desai, Suseelendra; Venkateswar Rao, L

2016-02-01

Two grams of delignified substrate at 10% (w/v) level was subjected to biphasic dilute acid hydrolysis using phosphoric acid, hydrochloric acid and sulfuric acid separately at 110 °C for 10 min in phase-I and 121 °C for 15 min in phase-II. Combinations of acid concentrations in two phases were varied for maximum holocellulose hydrolysis with release of fewer inhibitors, to select the suitable acid and its concentration. Among three acids, sulfuric acid in combination of 1 & 2% (v/v) hydrolyzed maximum holocellulose of 25.44±0.44% releasing 0.51±0.02 g/L of phenolics and 0.12±0.002 g/L of furans, respectively. Further, hydrolysis of delignified substrate using selected acid by varying reaction time and temperature hydrolyzed 55.58±1.78% of holocellulose releasing 2.11±0.07 g/L and 1.37±0.03 g/L of phenolics and furans, respectively at conditions of 110 °C for 45 min in phase-I & 121 °C for 60 min in phase-II. Copyright © 2015 Elsevier Ltd. All rights reserved.

Growth and membrane fluidity of food-borne pathogen Listeria monocytogenes in the presence of weak acid preservatives and hydrochloric acid

Directory of Open Access Journals (Sweden)

Ioannis eDiakogiannis

2013-06-01

Full Text Available This study addresses a major issue in microbial food safety, the elucidation of correlations between acid stress and changes in membrane fluidity of the pathogen Listeria monocytogenes. In order to assess the possible role that membrane fluidity changes play in L. monocytogenes tolerance to antimicrobial acids (acetic, lactic, hydrochloric acid at low pH or benzoic acid at neutral pH, the growth of the bacterium and the gel-to-liquid crystalline transition temperature point (Tm of cellular lipids of each adapted culture was measured and compared with unexposed cells. The Tm of extracted lipids was measured by Differential Scanning Calorimetry (DSC. A trend of increasing Tm values but not of equal extent was observed upon acid tolerance for all samples and this increase is not directly proportional to each acid antibacterial action. The smallest increase in Tm value was observed in the presence of lactic acid, which presented the highest antibacterial action. In the presence of acids with high antibacterial action such as acetic, hydrochloric acid or low antibacterial action such as benzoic acid, increased Tm values were measured. The Tm changes of lipids were also correlated with our previous data about fatty acid changes to acid adaptation. The results imply that the fatty acid changes are not the sole adaptation mechanism for decreased membrane fluidity (increased Tm. Therefore, this study indicates the importance of conducting an in-depth structural study on how acids commonly used in food systems affect the composition of individual cellular membrane lipid molecules.

Interaction of Benzimidazoles and Benzotriazole: Its Corrosion Protection Properties on Mild Steel in Hydrochloric Acid

Science.gov (United States)

Ramya, K.; Mohan, Revathi; Joseph, Abraham

2014-11-01

Synergistic hydrogen-bonded interaction of alkyl benzimidazoles and 1,2,3-benzotrizole and its corrosion protection properties on mild steel in hydrochloric acid at different temperatures have been studied using polarization, EIS, adsorption, surface studies, and computational methods. The extent of synergistic interaction increases with temperature. Quantum chemical approach is used to calculate some electronic properties of the molecules and to ascertain the synergistic interaction, inhibitive effect, and molecular structures. The corrosion inhibition efficiencies and the global chemical reactivity relate to some parameters, such as total energy, E HOMO, E LUMO, and gap energy (Δ E). 1,2,3-Benzotrizole interacts with benzimidazoles derivatives up to a bond length of approximately 1.99 Å. This interaction represents the formation of a hydrogen bond between the 1,2,3-benzotrizole and benzimidazoles. This synergistic interaction of 1,2,3-benzotrizole and benzimidazole derivatives offers extended inhibition efficiency toward mild steel in hydrochloric acid.

Synthesis and characterization of a novel organic corrosion inhibitor for mild steel in 1 M hydrochloric acid

Science.gov (United States)

Ahmed, Mohammed H. Othman; Al-Amiery, Ahmed A.; Al-Majedy, Yasmin K.; Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Gaaz, Tayser Sumer

2018-03-01

The synthesis and characterization of a novel organic corrosion inhibitor (4-(3-mercapto-5,6,7,8-tetrahydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazin-6-yl)phenol), for mild steel in 1 M hydrochloric acid (HCl) has been successfully reported for the first time. The inhibitor evaluated as corrosion inhibitor for mild steel in 1 M of Hydrochloric acid solution using electrochemical impedance spectroscopy (EIS), and electrochemical frequency modulation (EFM) measurement techniques. Changes in the impedance parameters suggested an adsorption of the inhibitor onto the mild steel surface, leading to the formation of protective films. The results show that the inhibition efficiencies increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. The maximum inhibition efficiency up to 67% at the maximum concentration 0.5 mM. This shows that those inhibitors are effective in helping to reduce and slowing down the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing an organic inhibitor for the mild steel that can be weakened by increasing the temperature. The adsorption process of the synthesized organic inhibitor depends on its electronic characteristics in addition to steric effects and the nature of metal surface, temperature degree and the varying degrees of surface-site activity. The synthesized inhibitor molecules were absorbed by metal surface and follow Langmuir isotherms.

The Comparison of Hydrochloric Acid and Phosphoric Acid Treatments in the Preparation of Montmorillonite Catalysts for RNA Synthesis.

Science.gov (United States)

Aldersley, Michael Frank; Joshi, Prakash C; Huang, Yixing

2017-09-01

The treatment of clay minerals with a preliminary acid wash and titration to pH 7 has proven to generate catalysts for the most interesting of oligomerization reactions in which activated RNA-nucleotides generate oligomers up to 40-mers. Significantly, not all clay minerals become catalytic following this treatment and none are catalytic in the absence of such treatment. The washing procedure has been modified and explored further using phosphoric acid and the outcomes are compared to those obtained when clay samples are prepared following a hydrochloric acid wash.

Controlled-potential coulometric determination of plutonium with a hydrochloric acid-sulfamic acid electrolyte and phosphate complexing

International Nuclear Information System (INIS)

Jackson, D.D.; Hollen, R.M.; Roensch, F.R.; Rein, J.E.

1981-01-01

Total plutonium is selectively determined by a controlled-potential coulometric method in which plutonium is reduced to Pu(III) at 0.25 V (vs. SCE) in a 5.5 M hydrochloric acid-0.015 M sulfamic acid electrolyte, diverse ions are oxidized at 0.57 V, phosphate is added to reduce the Pu(III)-Pu(IV) potential, and Pu(III) is oxidized to Pu(IV) at 0.68 V. None of more than 50 metal ions present in nuclear fuel-cycle material interferes. Many anions are without effect and most interfering ones are removed by preliminary fuming with perchloric acid. The apparatus described consists mainly of commercial components. The relative standard deviation is < 0.1% at the 5-mg plutonium level

Green approach to corrosion inhibition of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves

Energy Technology Data Exchange (ETDEWEB)

Quraishi, M.A., E-mail: maquraishi@rediffmail.com [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India); Singh, Ambrish; Singh, Vinod Kumar [Udai Pratap Autonomous College, Varanasi 221002 (India); Yadav, Dileep Kumar; Singh, Ashish Kumar [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India)

2010-07-01

The inhibition of the corrosion of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves has been studied using weight loss, electrochemical impedance spectroscopy (EIS), linear polarization and potentiodynamic polarization techniques. Inhibition was found to increase with increasing concentration of the leaves extract. The effect of temperature, immersion time and acid concentration on the corrosion behavior of mild steel in 1 M HCl and 0.5 M H{sub 2}SO{sub 4} with addition of extract was also studied. The inhibition was assumed to occur via adsorption of the inhibitor molecules on the metal surface. The adsorption of the extract on the mild steel surface obeys the Langmuir adsorption isotherm. The activation energy as well as other thermodynamic parameters (Q, {Delta}H*, and {Delta}S*) for the inhibition process was calculated. These thermodynamic parameters show strong interaction between inhibitor and mild steel surface. The results obtained show that the extract of the leaves of M. koenigii could serve as an effective inhibitor of the corrosion of mild steel in hydrochloric and sulphuric acid media.

Intramolecular synergistic effect of glutamic acid, cysteine and glycine against copper corrosion in hydrochloric acid solution

International Nuclear Information System (INIS)

Zhang Daquan; Xie Bin; Gao Lixin; Cai Qirui; Joo, Hyung Goun; Lee, Kang Yong

2011-01-01

The corrosion protection of copper by glutamic acid, cysteine, glycine and their derivative (glutathione) in 0.5 M hydrochloric acid solution has been studied by the electrochemical impedance spectroscopy and cyclic voltammetry. The inhibition efficiency of the organic inhibitors on copper corrosion increases in the order: glutathione > cysteine > cysteine + glutamic acid + glycine > glutamic acid > glycine. Maximum inhibition efficiency for cysteine reaches about 92.9% at 15 mM concentration level. The glutathione can give 96.4% inhibition efficiency at a concentration of 10 mM. The molecular structure parameters were obtained by PM3 (Parametric Method 3) semi-empirical calculation. The intramolecular synergistic effect of glutamic acid, cysteine and glycine moieties in glutathione is attributed to the lower energy of the lowest unoccupied molecular orbital (E LUMO ) level and to the excess hetero-atom adsorption centers and the bigger coverage on the copper surface.

Impact of α-amylase combined with hydrochloric acid hydrolysis on structure and digestion of waxy rice starch.

Science.gov (United States)

Li, Hongyan; Zhu, Yanqiao; Jiao, Aiquan; Zhao, Jianwei; Chen, Xiaoming; Wei, Benxi; Hu, Xiuting; Wu, Chunsen; Jin, Zhengyu; Tian, Yaoqi

2013-04-01

The structure and in vitro digestibility of native waxy rice starch by the combined hydrolysis of α-amylase and hydrochloric acid were investigated in this study. The combined hydrolysis technique generated higher hydrolysis rate and extent than the enzymatic hydrolysis. The granular appearance and chromatograph profile demonstrated that α-amylase and hydrochloric acid exhibited different patterns of hydrolysis. The rise in the ratio of absorbance 1047/1022cm(-1), the melting temperature range (Tc-To), and the melting enthalpy (ΔH) were observed during the combined hydrolysis. These results suggest that α-amylase simultaneously cleaves the amorphous and crystalline regions, whereas the amorphous regions of starch granules are preferentially hydrolyzed during the acid hydrolysis. Furthermore, the combined hydrolysis increased rapidly digestible starch (RDS) while decreased slowly digestible starch (SDS) and resistant starch (RS), indicating that the hydrolysis mode affected the digestion property of native waxy rice starch. Copyright © 2013 Elsevier B.V. All rights reserved.

Cefuroxime axetil: A commercially available drug as corrosion inhibitor for aluminum in hydrochloric acid solution

OpenAIRE

Ameh, Paul O.; Sani, Umar M.

2016-01-01

Cefuroxime axetil (CA) a prodrug was tested as corrosion inhibitor for aluminum in hydrochloric acid solution using thermometric, gasometric weight loss and scanning electron microscope (SEM) techniques. Results obtained showed that this compound has a good inhibiting properties for aluminum corrosion in acidic medium, with inhibition efficiencies values reaching 89.87 % at 0.5 g / L . It was also found out that the results from weight loss method are highly consistent with those obtained by ...

Corrosion Inhibition of Mild Steel in Hydrochloric Acid by Sodium Lauryl Sulfate (SLS)

OpenAIRE

Atul Kumar

2008-01-01

Effect of Sodium Lauryl Sulfate (SLS), a surfactant on corrosion of mild steel in 1 M hydrochloric acid was studied using three techniques namely: weight loss, electrochemical polarization and metallurgical research microscopy. Results obtained reveal that SLS is good inhibitor and shows very good corrosion inhibition efficiency (IE). The IE was found to vary with concentration of inhibitor and temperature. The electrochemical polarization result revealed that SLS is anodic in nature.

ESR study of /sup 99/Tc(II) complex formed by reduction of ammonium pertechnetate with ascorbic acid in concentrated hydrochloric acid

Energy Technology Data Exchange (ETDEWEB)

Kudo, T; Tsuchihashi, N; Ogata, T

1987-07-30

Paramagnetic /sup 99/Tc complex formed by the reduction of ammonium pertechnetate by ascorbic acid with excess sodium nitrite in concentrated hydrochloric acid was investigated by ESR technique. This complex had total electron spin S=1/2 and the obtained ESR parameters are 2.032, 2.043; and 264, 108 gauss, respectively. It was concluded that the formed species was low spin /sup 99/Tc(II) complex. (author) 13 refs.

Corrosion Inhibition of Mild Steel in Hydrochloric Acid by Sodium Lauryl Sulfate (SLS

Directory of Open Access Journals (Sweden)

Atul Kumar

2008-01-01

Full Text Available Effect of Sodium Lauryl Sulfate (SLS, a surfactant on corrosion of mild steel in 1 M hydrochloric acid was studied using three techniques namely: weight loss, electrochemical polarization and metallurgical research microscopy. Results obtained reveal that SLS is good inhibitor and shows very good corrosion inhibition efficiency (IE. The IE was found to vary with concentration of inhibitor and temperature. The electrochemical polarization result revealed that SLS is anodic in nature.

Separation of Rhenium from Lead-Rich Molybdenite Concentrate via Hydrochloric Acid Leaching Followed by Oxidative Roasting

Directory of Open Access Journals (Sweden)

Guanghui Li

2016-11-01

Full Text Available Lead-rich molybdenite is a typical rhenium-bearing molybdenum resource in China, which has not been efficiently utilized due to its high contents of lead and gangue minerals. In this study, hydrochloric acid was used for preliminarily removing lead and calcite from a lead-rich molybdenite concentrate. Oxidative roasting-ammonia leaching was then carried out for separation of rhenium and extraction of molybdenum. The hydrochloric acid leaching experiments revealed that 93.6% Pb and 97.4% Ca were removed when the leaching was performed at 95 °C for 10 min with HCl concentration of 8 wt. % and liquid-solid ratio of 5 (mL/g. The results of direct oxidative roasting indicated that 89.3% rhenium was volatilized from the raw concentrate after roasting at 600 °C for 120 min in air. In contrast, the rhenium volatilization was enhanced distinctly to 98.0% after the acid-leached concentrate (leaching residue was roasted at 550 °C for 100 min. By the subsequent ammonia leaching, 91.5% molybdenum was leached out from the calcine produced from oxidative roasting of the acid-leached concentrate, while only 79.3% Mo was leached from the calcine produced by roasting molybdenite concentrate without pretreatment.

Isolation of living Algae growing in the shells of Molluscs and Barnacles with EDTA (ethylenediaminetetraacetic acid)

NARCIS (Netherlands)

Prud’homme van Reine, W.F.; Hoek, van den C.

1966-01-01

Several decalcifying mixtures or aqueous solutions of inorganic or organic acids are generally used for releasing algae growing in the shells of molluscs and barnacles, for instance dilute hydrochloric, nitric, citric, or acetic acid (4), a mixture of nitric acid, chromic acid and alcolhol (1),

Synthesis and characterization of a novel organic corrosion inhibitor for mild steel in 1 M hydrochloric acid

Directory of Open Access Journals (Sweden)

Mohammed H. Othman Ahmed

2018-03-01

Full Text Available The synthesis and characterization of a novel organic corrosion inhibitor (4-(3-mercapto-5,6,7,8-tetrahydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazin-6-ylphenol, for mild steel in 1 M hydrochloric acid (HCl has been successfully reported for the first time. The inhibitor evaluated as corrosion inhibitor for mild steel in 1 M of Hydrochloric acid solution using electrochemical impedance spectroscopy (EIS, and electrochemical frequency modulation (EFM measurement techniques. Changes in the impedance parameters suggested an adsorption of the inhibitor onto the mild steel surface, leading to the formation of protective films. The results show that the inhibition efficiencies increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. The maximum inhibition efficiency up to 67% at the maximum concentration 0.5 mM. This shows that those inhibitors are effective in helping to reduce and slowing down the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing an organic inhibitor for the mild steel that can be weakened by increasing the temperature. The adsorption process of the synthesized organic inhibitor depends on its electronic characteristics in addition to steric effects and the nature of metal surface, temperature degree and the varying degrees of surface-site activity. The synthesized inhibitor molecules were absorbed by metal surface and follow Langmuir isotherms. Keywords: Corrosion, Inhibitor, Mild steel, EIS spectroscopy

Stepwise hydrochloric acid extraction of monazite hydroxides for the recovery of cerium lean rare earths, cerium, uranium and thorium

International Nuclear Information System (INIS)

Swaminathan, T.V.; Nair, V.R.; John, C.V.

1988-01-01

Monazite sand is normally processed by the caustic soda route to produce mixed rare earth chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earth chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earth chloride rather than the natural rare earth chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earth chloride, cerium, thorium and uranium from rare earth + thorium hydroxide obtained by treating monazite, based on stepwise hydrochloric acid extraction, was developed in the authors laboratory. The process involves drying of the mixed rare earth-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions

Investigation of copper(I sulphide leaching in oxidative hydrochloric acid solution

Directory of Open Access Journals (Sweden)

Branislav Marković

2015-12-01

Full Text Available Present work is focused on the copper (I sulphide leaching with sodium chloride in hydrochloric acid solution and with introduction of gaseous oxygen. Chemical reactions of leaching and their thermodynamic probabilities are predicted based on the literature data and products which were formed during the process and the overall leaching reaction was defined. The influence of temperature and time on the leaching degree of copper was experimentally determined. The quantity of dissolved copper increases with the increase of both investigated parameters. Elemental sulphur was formed as the main leaching product, precipitated at the particle surfaces and chloride ions have a role to disrupt the creation of this passive layer.

Comparison of sulfuric and hydrochloric acids as catalysts in hydrolysis of Kappaphycus alvarezii (cottonii).

Science.gov (United States)

Meinita, Maria Dyah Nur; Hong, Yong-Ki; Jeong, Gwi-Taek

2012-01-01

In this study, hydrolysis of marine algal biomass Kappaphhycus alvarezii using two different acid catalysts was examined with the goal of identifying optimal reaction conditions for the formation of sugars and by-products. K. alvarezii were hydrolyzed by autoclave using sulfuric acid or hydrochloric acid as catalyst with different acid concentrations (0.1-1.0 M), substrate concentrations (1.0-13.5%), hydrolysis time (10-90 min) and hydrolysis temperatures (100-130 (°)C). A difference in galactose, glucose, reducing sugar and total sugar content was observed under the different hydrolysis conditions. Different by-product compounds such as 5-hydroxymethylfurfural and levulinic acid were also observed under the different reaction conditions. The optimal conditions for hydrolysis were achieved at a sulfuric acid concentration, temperature and reaction time of 0.2 M, 130 °C and 15 min, respectively. These results may provide useful information for the development of more efficient systems for biofuel production from marine biomass.

Extraction of copper zinc and iron from hydrochloric acid solutions by means of different extractants

Energy Technology Data Exchange (ETDEWEB)

Zhivkova, Svetlana [Institute of Chemical Engineering - Bulgarian Academy of Sciences, Sofia (Bulgaria)

2011-07-01

The extraction of copper, zinc and iron from hydrochloric acid solutions has been studied. The experiments have been carried out using various solvents, involving different extraction mechanisms – solvating, anion-exchange, cation-exchange, bifunctional . Mixtures of these extractants have been also used. The extraction properties of these extractant mixtures toward copper, zinc and iron, the effect of used modifiers and diluents have been also investigated. Key words: Copper, Zinc, Iron, Extraction, Extractant, Modifier, Diluent.

Simultaneous Recovery of Hydrogen and Chlorine from Industrial Waste Dilute Hydrochloric Acid

Directory of Open Access Journals (Sweden)

N. Paidimarri

2016-01-01

Full Text Available Recovery of chlorine from byproduct HCl has inevitable commercial importance in industries lately because of insufficient purity or too low concentration to recycle it. Instead it is being neutralized in industries before disposing to meet stringent environmental conditions. Although recovery through catalytic oxidation processes is studied since the 19th century, their high operating conditions combined with sluggish reaction kinetics and low single pass conversions make electrolysis a better alternative. The present motive of this work is to develop a novel electrolysis process which in contrast to traditional processes effectively recovers both hydrogen and chlorine from dilute HCl. For this, an electrolytic cell with an Anionic Exchange Membrane has been designed which only allows the passage of chlorine anions from catholyte to anolyte separating the gasses in a single step. The catholyte can be as low as 3.59 wt% because of fixed anolyte concentration of 1.99 wt% which minimizes oxygen formation. Preliminary results show that the simultaneous recovery of hydrogen and chlorine is possible with high conversion up to 98%. The maximum current density value for 4.96 cm2 membrane surface area (70% active surface area is 2.54 kAm−2, which is comparable with reported commercial processes. This study is expected to be useful for process intensification of the same in a continuous process environment.

Quantitative Leaching of a Spent Cell Phone Printed Circuit Board by Hydrochloric acid

Directory of Open Access Journals (Sweden)

Alafara A. Baba

2014-07-01

Full Text Available This paper presents a kinetic data on the hydrometallurgical recovery of some metal ions from a printed circuit board (PCB of a spent cell phone by hydrochloric acid leaching. The effects of acid concentration, temperature and particle diameter on the dissolution efficiency at various leaching time intervals were examined. The results of the leaching investigations showed that the powdered cell phone dissolution increases with increasing acid concentration, system temperature with decreasing particle diameter at 360 rpm. With 2M HCl solution, about 88.49% of the sample was dissolved within 120 minutes using 0.075-0.112 mm particle diameter at 800 C. The results of the study indicated that the dissolution reaction could be represented by a shrinking core model with surface chemical reaction. A value of 0.61, 60.67 kJ/mol and 12.9s-1 were calculated as reaction order, activation energy and frequency factor, respectively for the dissolution process.

Leaching of Titanium and Silicon from Low-Grade Titanium Slag Using Hydrochloric Acid Leaching

Science.gov (United States)

Zhao, Longsheng; Wang, Lina; Qi, Tao; Chen, Desheng; Zhao, Hongxin; Liu, Yahui; Wang, Weijing

2018-05-01

Acid-leaching behaviors of the titanium slag obtained by selective reduction of vanadium-bearing titanomagnetite concentrates were investigated. It was found that the optimal leaching of titanium and silicon were 0.7% and 1.5%, respectively. The titanium and silicon in the titanium slag were firstly dissolved in the acidic solution to form TiO2+ and silica sol, and then rapidly reprecipitated, forming hydrochloric acid (HCl) leach residue. Most of the silicon presented in the HCl leach residue as floccules-like silica gel, while most of the titanium was distributed in the nano-sized rod-like clusters with crystallite refinement and intracrystalline defects, and, as such, 94.3% of the silicon was leached from the HCl leach residue by alkaline desilication, and 96.5% of the titanium in the titanium-rich material with some rutile structure was then digested by the concentrated sulfuric acid. This provides an alternative route for the comprehensive utilization of titanium and silicon in titanium slag.

Studies on the interference of hydrofluoric acid and phosphoric acid in the determination of uranium using Ti(III) reduction method-biamperometry end point

International Nuclear Information System (INIS)

Shiny, T.S.; Rajalakshmi, A.; Phal, D.G.; Charyulu, M.M.; Ramakumar, K.L.

2007-01-01

Accurate and precise determination of uranium in nuclear materials is necessary for chemical quality control as well as for nuclear material accounting purposes. Different types of uranium samples are received for the measurements. Depending upon the nature of the sample dissolution procedure is selected. Mixed oxide samples of uranium and plutonium, for example, are dissolved in nitric acid containing hydrofluoric acid under IR lamp. The fluoride ions are removed by repeated evaporation of the solution. However, some fluoride ions are left in the solutions depending on the conditions of evaporation. Uranium samples and alloy samples are dissolved in dilute hydrochloric acid. The rate of dissolution depends on concentration of acid. Sometimes a mixture of hydrochloric acid and hydrofluoric acid is used for the dissolution metal alloy samples, which may contain silica. Another method of dissolution of these samples is using a mixture of phosphoric acid and 1% hydrofluoric acid. It is necessary to study the interference of hydrofluoric acid and phosphoric acid on the determination of uranium

Comparison of bile acid synthesis determined by isotope dilution versus fecal acidic sterol output in human subjects

International Nuclear Information System (INIS)

Duane, W.C.; Holloway, D.E.; Hutton, S.W.; Corcoran, P.J.; Haas, N.A.

1982-01-01

Fecal acidic sterol output has been found to be much lower than bile acid synthesis determined by isotope dilution. Because of this confusing discrepancy, we compared these 2 measurements done simultaneously on 13 occasions in 5 normal volunteers. In contrast to previous findings, bile acid synthesis by the Lindstedt isotope dilution method averaged 16.3% lower than synthesis simultaneously determined by fecal acidic sterol output (95% confidence limit for the difference - 22.2 to -10.4%). When one-sample determinations of bile acid pools were substituted for Lindstedt pools, bile acid synthesis by isotope dilution averaged 5.6% higher than synthesis by fecal acidic sterol output (95% confidence limits -4.9 to 16.1%). These data indicate that the 2 methods yield values in reasonably close agreement with one another. If anything, fecal acidic sterol outputs are slightly higher than synthesis by isotope dilution

Furfuryl alcohol as corrosion inhibitor for N80 steel in hydrochloric acid

International Nuclear Information System (INIS)

Vishwanatham, S.; Haldar, N.

2008-01-01

The ability of furfuryl alcohol (FA) as corrosion inhibitor in controlling corrosion of N80 steel in 15% hydrochloric acid has been investigated. It is found that the percentage inhibition of FA increases almost linearly with its concentration (in the range 10 mM-80 mM) and attains about 91% at 80 mM. FA shows significant inhibition at higher temperatures also (∼82% at 60 deg. C;∼74% at 110 deg. C with 80 mM concentration). FA undergoes acid catalyzed polymerization under the experimental conditions to give polyfurfuryl alcohols (PFA) as evidenced by FTIR and NMR spectral data. Thermodynamic parameters for the corrosion of steel in presence and absence of the inhibitor have been calculated. The inhibitive action may be attributed to adsorption of inhibitor molecules on the active sites of the metal surface following Temkin adsorption isotherm. Potentiodynamic polarization curves indicate that FA acts as mixed type inhibitor. A plausible mechanism for the mode of inhibition has been proposed

Kinetic Aspects of Leaching Zinc from Waste Galvanizing Zinc by Using Hydrochloric Acid Solutions

Science.gov (United States)

Sminčáková, Emília; Trpčevská, Jarmila; Pirošková, Jana

2017-10-01

In this work, the results of acid leaching of flux skimmings coming from two plants are presented. Sample A contained two phases, Zn(OH)Cl and NH4Cl. In sample B, the presence of three phases, Zn5(OH)8Cl2·H2O, (NH4)2(ZnCl4) and ZnCl2(NH3)2, was proved. The aqueous solution of hydrochloric acid and distilled water was used as the leaching medium. The effects of the leaching time, temperature and concentration of the leaching medium on the zinc extraction were investigated. The apparent activation energy, E a = 4.61 kJ mol-1, and apparent reaction order n = 0.18 for sample A, and the values E a = 6.28 kJ mol-1 and n = 0.33 for sample B were experimentally determined. Zinc leaching in acid medium is a diffusion-controlled process.

Solvent Extraction of Tungsten(VI) from Moderate Hydrochloric Acid Solutions with LIX 63

Energy Technology Data Exchange (ETDEWEB)

Truong, Hoai Thanh; Lee, Man Seung [Mokpo National University, Jeollanamdo (Korea, Republic of); Kim, Yong Hwan [Incheon Technology Service Centre, Incheon (Korea, Republic of)

2017-06-15

The solvent extraction of tungsten(VI) from hydrochloric acid solutions using 5,8-diethyl-7-hydroxydodecan-6-one oxime (LIX 63) was analyzed in solutions having an initial pH range from 2 to 5, by varying the concentration of metal and extractant. In our experimental range, the cationic exchange reaction as well as the solvation reaction occurred simultaneously. The cation exchange reaction was identified by applying a slope analysis method to the extraction data. The existence of cationic tungsten(VI) species was confirmed by ion exchange experiments with Diphonix resin at pH 3. Further study is needed to identify the nature of this tungsten cationic species.

Investigating the Acid Failure of Aluminium Alloy in 2 M Hydrochloric Acid Using Vernonia amygdalina

Directory of Open Access Journals (Sweden)

Olugbenga A. Omotosho

2012-04-01

Full Text Available The acid failure of aluminium alloy in 2 M hydrochloric acid solution in the presence of Vernonia amygdalina extract was investigated using gasometric technique. Aluminium alloy coupons of dimension 4 cm by 1 cm were immersed in test solutions of free acid and also those containing extract volumes of 2, 3, 4 and 5 cm3 at ambient temperature for 30 minutes. The volumes of hydrogen gas evolved as a result of the rate of reaction were recorded and analyzed. Analysis revealed that maximum inhibitor efficiency which corresponds to the lowest corrosion rate was obtained at optimum inhibitor volumes of 5 cm3, with reduction in the corrosion rate observed to follow in order of increasing extract volumes. Adsorption study revealed that Temkin isotherm best described the metal surface interaction with the extract phytochemicals, with 12 minutes becoming the best exposure time for the phytochemicals to adsorb to the metal surface at all volumes. Statistical modelling of the corrosion rate yielded an important relationship suitable for estimating corrosion rate values once volumes of the extract is known. Microstructural studies, showed an indirect relationship between crack growth rates and extract volumes, while consistency of the irregular intermetallic phases increases with increasing extract volumes.

FERMENTABLE SUGARS FROM Lupinus rotundiflorus BIOMASS BY HYDROCHLORIC ACID HYDROLYSIS

Directory of Open Access Journals (Sweden)

Mario A. Ruiz-López

2011-02-01

Full Text Available It is of general interest to produce fermentable carbohydrates from plant biomass. However, obtaining monosaccharides requires some effort, due to the intricate structure of the cell wall lignocellulosic complex. The aim of this study was to apply a simple two-stage hydrolysis process, using only concentrated hydrochloric acid, to generate fermentable carbohydrates from L. rotundiflorus biomass. First and second stage acid concentrations were 32% and 42.6%. Total monosaccharide yields with respect to dry matter after the first stage, second stage, and the overall process, were 27.5%, 21.0% and 48.4%, respectively. Xylose was the main first stage carbohydrate in the hydrolysate, followed by glucose, arabinose, and galactose. After the second stage only glucose and a small amount of xylose were detected. The polysaccharide hydrolysis was eased by overall low lignin content. Some advantages of this method were the use of a single hydrolyzing agent and that most of the polysaccharides were hydrolyzed in reasonably high yields. The acceptable yield, relative simplicity, the use of most of the biomass along with the wide availability, low cost of the chemicals, and the ample supply of lupines, would facilitate the scaling of these laboratory studies to pilot and industrial levels.

Hydrochloric acid: an overlooked driver of environmental change.

Science.gov (United States)

Evans, Chris D; Monteith, Don T; Fowler, David; Cape, J Neil; Brayshaw, Susan

2011-03-01

Research on the ecosystem impacts of acidifying pollutants, and measures to control them, has focused almost exclusively on sulfur (S) and nitrogen (N) compounds. Hydrochloric acid (HCl), although emitted by coal burning, has been overlooked as a driver of ecosystem change because most of it was considered to redeposit close to emission sources rather than in remote natural ecosystems. Despite receiving little regulatory attention, measures to reduce S emissions, and changes in energy supply, have led to a 95% reduction in United Kingdom HCl emissions within 20 years. Long-term precipitation, surface water, and soil solution data suggest that the near-disappearance of HCl from deposition could account for 30-40% of chemical recovery from acidification during this time, affecting both near-source and remote areas. Because HCl is highly mobile in reducing environments, it is a more potent acidifier of wetlands than S or N, and HCl may have been the major driver of past peatland acidification. Reduced HCl loadings could therefore have affected the peatland carbon cycle, contributing to increases in dissolved organic carbon leaching to surface waters. With many regions increasingly reliant on coal for power generation, HCl should be recognized as a potentially significant constituent of resulting emissions, with distinctive ecosystem impacts.

Ruthenium (4) and ruthenium (3) state in hydrochloric acid solutions under microwave irradiation

International Nuclear Information System (INIS)

Bashilov, A.V.; Kuz'min, N.M.; Nesterov, A.A.; Runov, V.K.

2000-01-01

Reactions of hydration, poly- and depolymerization, oxidation-reduction processes with ruthenium (4) and ruthenium (3) participation are investigated in hydrochloric acid solutions under microwave irradiation by the methods of molecular absorption spectroscopy in UV visible region taking K 4 [Ru 2 OCl 10 ] as an example. Content of state forms of ruthenium (4) and ruthenium (3), absorption characteristics of forming complexes are calculated. Variation of microwave irradiation parameters and HCl concentration permits to prepare solutions containing [RuCl 6 ] 2+ (95 %) and [(RuOH) 2 (H 2 O) 6 (OH) 2 ] 4+ (98 %) preeminently predominant forms. The role of microwave effect directly is established taking as an example the process of ruthenium (4) hydration [ru

Multistage dilute acid leaching of a medium grade iron ore to super-concentrate

Directory of Open Access Journals (Sweden)

Adeleke A.A.

2014-01-01

Full Text Available The phosphorous laden Koton Karfe iron ore is a medium grade iron ore deposit in Nigeria that can be upgraded as a super-concentrate for use at the Aladja Steel Midrex plant. The 75 μm size sample fraction of the ore was preconcentrated with shaking table and leached in the oven at atmospheric pressure with dilute hydrochloric acid in single and multistage leaching sequences of H2O-HCl-H2O and HCl-H2O-H2O. The as-received, as-tabled and asleached samples were then subjected to X-ray fluorescence and microscopic analyses. The results obtained showed that the H2O-HCl-H2O route produced a higher grade concentrate that assayed 68.54% Fe indicating about 58% upgrade in iron content; while the phosphorus and sulphur contents were reduced by about 77 and 99.6% respectively. In addition, the silicon, manganese, and titanium contents were drastically reduced, while potassium was completely eliminated. The upgrade of iron content in the ore to 68.54% and the drastic reduction in phosphorous and sulphur contents has thus rendered the Koton Karfe iron ore suitable for use as a super concentrate for the Aladja steel plant direct reduction iron making process.

Highly improved synthesis of gold nanobipyramids by tuning the concentration of hydrochloric acid

Energy Technology Data Exchange (ETDEWEB)

Qi, Ying; Zhu, Jian; Li, Jianjun; Zhao, Junwu, E-mail: nanoptzhao@163.com [Xi’an Jiaotong University, The Key Laboratory of Biomedical Information Engineering of Ministry of Education, School of Life Science and Technology (China)

2016-07-15

Fabrication of gold nanobipyramids (Au BPs) has attracted great attention because they exhibit more advantageous plasmonic properties. In this study, Au BPs were synthesized by the well-known seeded growth in the presence of hydrochloric acid (HCl). The effects of the ingredients, including HCl, silver nitrate (AgNO{sub 3}), l-Ascorbic acid (AA), and seeds on the structure and yield of the Au BPs were systemically investigated. The results showed that the abundant HCl could improve the yield of Au BPs and decrease the longitudinal surface plasmon resonance wavelength. Under the circumstance of higher concentration of AA and AgNO{sub 3}, more byproducts were resulted. In addition, the effect of HCl under different ratios of seed solution to AA has also been studied. The results showed that the yield was less sensitive to HCl when the amount of seed solution was small. If substantial AA was added to the system, then abundant HCl should be introduced correspondingly to improve the yield of Au BPs.

Sodium phthalamates as corrosion inhibitors for carbon steel in aqueous hydrochloric acid solution

International Nuclear Information System (INIS)

Flores, Eugenio A.; Olivares, Octavio; Likhanova, Natalya V.; Dominguez-Aguilar, Marco A.; Nava, Noel; Guzman-Lucero, Diego; Corrales, Monica

2011-01-01

Highlights: → N-Alkyl-sodium phthalamates as corrosion inhibitors for industry in acidic medium. → Compounds behaved as mixed type inhibitors and followed Langmuir adsorption isotherm. → Efficiencies were proportional to aliphatic chain length and inhibitor concentration. → Iron complexes and chelates with phthalamates contributed to carbon steel protection. - Abstract: Three compounds of N-alkyl-sodium phthalamates were synthesized and tested as corrosion inhibitors for carbon steel in 0.5 M aqueous hydrochloric acid. Tests showed that inhibitor efficiencies were related to aliphatic chain length and dependent on concentration. N-1-n-tetradecyl-sodium phthalamate displayed moderate efficiency against uniform corrosion, 42-86% at 25 deg. C and 25-60% at 40 o C. Tests indicated that compounds behave as mixed type inhibitors where molecular adsorption on steel followed Langmuir isotherm, whereas thermodynamic suggested that a physisorption process occurred. XPS analysis confirmed film formation on surface, where Fe +2 complexes and Fe +2 chelates with phthalamates prevented steel from further corrosion.

Contribution to the study of the physico-chemical mechanisms of metallic cation extraction by alkylphosphoric acids. Extraction of zirconium (IV) by di-2-ethylhexyl phosphoric acid (DEHPA)

International Nuclear Information System (INIS)

Carbonnier, J.-L.

1979-02-01

Extraction of zirconium, especially at high concentration (0.1M), by dodecane diluted DEHPA (HA) from hydrochloric or nitric aqueous phases of 0.1 to 10 M acidity was studied. The composition, structure and polymerisation of the complexes extracted were determined by chemical analysis, viscosimetry, infrared spectrometry and light scattering. A Zr(OH) 2 A 2 .2HNO 3 , type structure is proposed for these complexes instead of the generally accepted form: Zr(OH) 2 (NO 3 ) 2 .2HA. Similarly in hydrochloric solution: Zr(OH) 2 A 2 .2HCl. Polymerisation in the organic phase results from the juxtaposition of two factors; firstly zirconium saturation (formation of bridges by DEHPA between zirconium atoms) and secondly the nature the equeous phase. In slightly acid hydrochloric solution (pH = 1.3) the aqueous plymers of zirconium are extracted in the organic phase as polynuclear complexes; in nitric solution no polynuclear complexes are observed but the nitric acid molecules extracted set up hydrogen bonds which explain the increased viscosity and gelification of the organic phases [fr

Interaction Studies of Dilute Aqueous Oxalic Acid

Directory of Open Access Journals (Sweden)

Kiran Kandpal

2007-01-01

Full Text Available Molecular conductance λm, relative viscosity and density of oxalicacid at different concentration in dilute aqueous solution were measured at 293 K.The conductance data were used to calculate the value association constant.Viscosity and density data were used to calculate the A and B coefficient ofJone-Dole equation and apparent molar volume respectively. The viscosityresults were utilized for the applicability of Modified Jone-Dole equation andStaurdinger equations. Mono oxalate anion acts, as structure maker and thesolute-solvent interaction were present in the dilute aqueous oxalic acid.

Optimisation of Dilute Sulphuric Acid Hydrolysis of Waste ...

African Journals Online (AJOL)

Dilute sulphuric acid hydrolysis of waste paper was investigated in this study. The effects of acid concentration, time, temperature and liquid to solid ratio on the total reducing sugar concentration were studied over three levels using a four variable Box-Behnken design (BBD). A statistical model was developed for the ...

Characterization of Polyamide 66 membranes prepared by phase inversion using formic acid and hydrochloric acid such as solvents

Directory of Open Access Journals (Sweden)

Patrícia Poletto

2011-12-01

Full Text Available The membranes properties prepared from water/formic acid (FA/ polyamide 66 (PA66 and water/hydrochloric acid (HCl/polyamide 66 (PA 66 systems has been studied. The different solvents interact distinctly with the polymer, affecting the membrane morphology. The asymmetric structure of the membranes showed a dense top layer and a porous sublayer. The membranes M-HCl prepared from HCl/PA 66 system showed a larger dense layer (around 23 μm in compared to those prepared from FA/PA 66 system (M-FA (around 10 μm. The membrane morphology was a determinant factor in results of water absorption, porosity and pure water flux. The lower thickness of dense layer in M-FA membranes resulted in a higher water absorption and, consequently, porosity, approximately 50%, compared with M-HCl membranes, approximately 15%. The same trend was observed to permeate flux, the lower thickness of dense layer higher pure water flux.

Inhibitive effect of a naturally-occurring substance, tobacco, on the dissolution of mild steel in hydrochloric acid

Energy Technology Data Exchange (ETDEWEB)

Srivastava, K; Srivastava, P

1980-12-01

A number of naturally-occurring substances has been found to be effective inhibitors for the dissolution of mild steel in hydrochloric acid. The alkaloids nicotine and papaverine, contained in natural products such as tobacco leaves and black pepper, have proved themselves as excellent inhibitors. Considering the low cost of tobacco leaves, detailed studies were made with these, and they have been found to form an effective inhibitor under all practical conditions. Adsorption studies based on weight-loss measurements showed that adsorption of inhibitor obeys Freundlich's adsorption isoth

The liquid-liquid extraction of chloro-(trichlorostannato)-rhodium(I/III) and -ruthenium (II) complexes from dilute hydrochloric acid into 4-methylpentan-2-one

International Nuclear Information System (INIS)

Wyrley-Birch, J.M.

1984-10-01

The effect of stannous chloride on the liquid-liquid extraction of rhodium and ruthenium from hydrochloric acid solutions into 4-methyl-pentan-2-one (MIBK)/hexane mixtures was studied in detail. Stannous chloride concentrations were found to considerably increase the efficiency of the extraction of rhodium and ruthenium into the organic phase. Chloro-(trichlorostannato)-rhodium (I/III) complexes were formed at room temperature. The rate of chloro-(trichlorostannato)-ruthenium (II) complex formation was extremely slow at room temperature, but increased on heating of the aqueous solutions. The amount of rhodium and ruthenium extracted into the organic phase depend on the Sn(II):M molar ratio, the HCl, H sup(+) and Cl sup(-) concentrations, as well as the equilibration time. A 119 Sn NMR study of the MIBK extracts, showed that the stoichiometry of the chloro-(trichlorostannato)-rhodium (I/III) complexes extracted into the organic phase was dependent on the Sn(II):Rh(III) molar ratio as well as the HCl, H sup(+) and Cl sup(-) concentrations in the aqueous phase. The predominant species observed in the organic phase from HCl solutions containing Sn(II):Rh(III) ratios >= 5:1, was shown to be an hydrido complex having the form [RhH(SnCl 3 ) 4 Cl] 3 sup(-) or [RhH(SnCl 3 ) 4 ]2 sup(-). An essentially quantitative separation of rhodium and ruthenium was achieved utilising the variation in the rates of rhodium-tin and ruthenium-tin complex formation

Physicochemical aspects of decomposition of silica-alumina ores of argillites and green clays of Chashma-Sang Deposit of the Republic of Tajikistan by hydrochloric and nitric acids

International Nuclear Information System (INIS)

Kayumov, A.M.

2018-01-01

The purpose of work is to study the processes of decomposition of silica-alumina ores of argillites and green clays of Chashma-Sang Deposit of the Republic of Tajikistan by hydrochloric and nitric acids in temperature interval 20-98 deg C with the using of methods of selective extraction of valuable materials; elaboration of rational conditions of decomposition of raw material. Physicochemical properties of initial aluminium comprising ores, intermediate and final products of processing of argillites and green clays have been studied. Kinetic parameters of processes at acidic decomposition of argillites and green clays have been studied as well. The kinetic parameters of processes of decomposition of green clays and argillites by nitric and hydrochloric acids have been calculated. The flowsheet of complex processing of green clays and argillites of Chashma-Sang Deposit has been elaborated.

Selective liquid-liquid extraction of antimony(III from hydrochloric acid media by N-n-octylaniline in xylene

Directory of Open Access Journals (Sweden)

M. A. ANUSE

2004-04-01

Full Text Available N-n-Octylaniline in xylene was used for the extraction separation of antimony(III from hydrochloric acid media. Antimony(III was extracted quantitatively with 10 mL 4 % N-n-octylaniline in xylene. It was stripped from the organic phase with 0.5 M ammonia and estimated photometrically by the iodide method. The effect of metal ion, acid, reagent concentration and various foreign ions was investigated. The method affords binary and ternary separation of antimony(III from tellurium(IV, selenium(IV, lead(II, bismuth(III, tin(IV, germanium(IV, copper(II, gold(III, iron(III and zinc(II. The method is applicable for the analysis of synthetic mixtures, alloys and semiconductor thin films. It is fast, accurate and precise.

Extraction of Sm(IIIand Nd(III with N,N,N’,N’-tetrabutyl-3-oxy-diglycolamidefrom hydrochloric acid

Directory of Open Access Journals (Sweden)

Yang J.H.

2013-01-01

Full Text Available The extraction behavior of Sm(III and Nd(III with N,N,N’,N’-tetrabutyl-3-oxa-diglycolamide (TBDGA in 70% kerosene-30% n-octanol from hydrochloride acid wasstudied. The effect of hydrochloric acid concentration, extractant concentration,and temperature on the distribution of rare earth elementswas investigated. The extraction mechanism was established and the stoichiometry of the main extracted species was confirm to be SmCl3•2TBDGA and NdCl3•2TBDGA for Sm(III and Nd(III, respectively. The extraction distribution ratio decreases with an increase in temperature, which demonstrates that the extraction reaction is exothermic. The IR spectra of the loaded organic phase and free extractant were recorded and discussed.

Physicochemical and in vitro antioxidant properties of pectin extracted from hot pepper (Capsicum annuum L. var. acuminatum (Fingerh.)) residues with hydrochloric and sulfuric acids.

Science.gov (United States)

Xu, Honggao; Tai, Kedong; Wei, Tong; Yuan, Fang; Gao, Yanxiang

2017-11-01

Transformation of hot pepper residues to value-added products with concomitant benefits on environmental pollution would be of great value to capsicum oleoresin manufacturers. Pectin, a soluble dietary fiber with multiple functions, from hot pepper residues was investigated in this study. The extraction of hot pepper pectin using hydrochloric acid was first optimized using response surface methodology (RSM). The most efficient parameters for maximum hot pepper pectin yield (14.63%, dry basis) were a pH of 1.0, a temperature of 90 °C, an extraction time of 2 h and a liquid-to-solid ratio of 20 L g -1 . The pectin was mainly composed of uronic acids, and the major neutral sugars were galactose and glucose. The structure of hot pepper pectin was characterized by homogalacturonan and rhamnogalacturonan I elements. The physicochemical properties of hot pepper pectin extracted by sulfuric acid and hydrochloric acid were further investigated. The content of protein and degree of esterification in hot pepper pectin extracted with sulfuric acid solution (SP) were higher (P hot pepper pectin, hot pepper residues would be a new source to obtain pectin, and SP would be more preferred than HP. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid

International Nuclear Information System (INIS)

Kurbanov, A.R.; Sharipov, D.Sh.

1993-01-01

Present article is devoted to calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid. The calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid was carried out in order to determine the thermal effects of reactions. The results of interaction of Ba(OH) 4 ·8H 2 O with 5, 10, and 20% solution of hydrofluoric acid were considered.

Kinetics of Ni3S2 sulfide dissolution in solutions of sulfuric and hydrochloric acids

Science.gov (United States)

Palant, A. A.; Bryukvin, V. A.; Vinetskaya, T. N.; Makarenkova, T. A.

2008-02-01

The kinetics of Ni3S2 sulfide (heazlewoodite) dissolution in solutions of hydrochloric and sulfuric acids is studied. The process under study in the temperature range of 30 90°C is found to occur in a kinetic regime and is controlled by the corresponding chemical reactions of the Ni3S2 decomposition by solutions of inorganic acids ( E a = 67 92 kJ/mol, or 16 22 kcal/mol). The only exception is the Ni3S2-HCl system at elevated temperatures (60 90°C). In this case, the apparent activation energy decreases sharply to 8.8 kJ/mol (2.1 kcal/mol), which is explained by the catalytic effect of gaseous chlorine formed under these conditions. The studies performed are related to the physicochemical substantiation of the hydrometallurgical processing of the copper-nickel converter mattes produced in the industrial cycle of the Norilsk Mining Company.

Modification of ntezi bentonite structure by hydrochloric acid: process kinetics and structural properties of the modified samples

International Nuclear Information System (INIS)

Ajemba, R.O.

2014-01-01

Bentonite from Ntezi was modified by reacting it with different concentrations of hydrochloric acid solutions. The modified samples were analysed by x-ray fluorescence. The kinetics of the modification reaction was studied by performing the experiment at different temperatures and times. Results of the analysis of the modified samples showed that the octahedral cations were removed which altered the chemical composition of the bentonite. The surface area and adsorptive capacity of the bentonite were improved after the modification. The kinetic studies showed that the acid modification reaction is controlled by the product layer diffusion and can be represented by (1-(l-X)/sup 1/3)/sup 2/ = k t; where, X is the fraction of the bentonite dissolved at time t. The activation energy was determined to be 24.98 kJ/mol. (author)

Di-n-butylamine as an inhibitor for the corrosion of aluminium alloys in hydrochloric acid solutions

Energy Technology Data Exchange (ETDEWEB)

Unni, V K.V.; Rama Char, T L

1965-01-01

Di-n-butylamine is a satisfactory inhibitor for the corrosion of aluminum-manganese alloy in hydrochloric acid solutions. Polarization studies indicate that the anode polarization is negligible, whereas the cathode polarization is appreciable and is increased by the inhibitor. The Tafel plot holds good in this case. The dissolution of the metal is electrochemical in character; the corrosion process appears to be under cathodic control. The efficiency increases with time, the effect being quite significant up to about 3 hr. It increases with increases in concentration of the inhibitor up to a certain value beyond which it is constant. The values increase with acid concentration up to 1.25 N., and remain practically unchanged thereafter. An acid concentration of 1.25 N. and an inhibitor concentration of 0.5 g per liter of nitrogen can be regarded as the optimum from the viewpoint of efficiency, the value being in the range 57-84%. The efficiency of the inhibitor for the aluminum-manganese alloy is about the same order as for pure aluminum. (10 refs.)

Physical and chemical mechanism underlying ultrasonically enhanced hydrochloric acid leaching of non-oxidative roasting of bastnaesite.

Science.gov (United States)

Zhang, Dongliang; Li, Mei; Gao, Kai; Li, Jianfei; Yan, Yujun; Liu, Xingyu

2017-11-01

In this study, we investigated an alternative to the conventional hydrochloric acid leaching of roasted bastnaesite. The studies suggested that the rare earth oxyfluorides in non-oxidatively roasted bastnaesite can be selectively leached only at elevated temperatures Further, the Ce(IV) in oxidatively roasted bastnaesite does not leach readily at low temperatures, and it is difficult to induce it to form a complex with F - ions in order to increase the leaching efficiency. Moreover, it is inevitably reduced to Ce(III) at elevated temperatures. Thus, the ultrasonically-assisted hydrochloric acid leaching of non-oxidatively roasted bastnaesite was studied in detail, including, the effects of several process factors and the, physical and chemical mechanisms underlying the leaching process. The results show that the leaching rate for the ultrasonically assisted process at 55°C (65% rare earth oxides) is almost the same as that for the conventional leaching process at 85°C. Based on the obtained results, it is concluded that ultrasonic cavitation plays a key role in the proposed process, resulting not only in a high shear stress, which damages the solid surface, but also in the formation of hydroxyl radicals (OH) and hydrogen peroxide (H 2 O 2 ). Standard electrode potential analysis and experimental results indicate that Ce(III) isoxidized by the hydroxyl radicals to Ce(IV), which can be leached with F - ions in the form of a complex, and that the Ce(IV) can subsequently be reduced to Ce(III) by the H 2 O 2. This prevents the Cl - ions in the solution from being oxidized to form chlorine. These results imply that the ultrasonically-assisted process can be used for the leaching of non-oxidatively roasted bastnaesite at low temperatures in the absence of a reductant. Copyright © 2017 Elsevier B.V. All rights reserved.

Study of Enzymatic Hydrolysis of Dilute Acid Pretreated Coconut Husk

Directory of Open Access Journals (Sweden)

Rudy Agustriyanto

2012-12-01

Full Text Available Coconut husk is classified as complex lignocellulosic material that contains cellulose, hemicellulose, lignin, and some other extractive compounds. Cellulose from coconut husk can be used as fermentation substrate after enzymatic hydrolysis. In contrary, lignin content from the coconut husk will act as an inhibitor in this hydrolysis process. Therefore, a pretreatment process is needed to enhance the hydrolysis of cellulose. The objective of this research is to investigate the production of the glucose through dilute acid pretreatment and to obtain its optimum operating conditions. In this study, the pretreatment was done using dilute sulfuric acid in an autoclave reactor. The pretreatment condition were varied at 80°C, 100°C, 120°C and 0.9%, 1.2%, 1.5% for temperature and acid concentration respectively. The acid pretreated coconut husk was then hydrolyzed using commercial cellulase (celluclast and β-glucosidase (Novozyme 188. The hydrolysis time was 72 hours and the operating conditions were varied at several temperature and pH. From the experimental results it can be concluded that the delignification temperature variation has greater influence than the acid concentration. The optimum operating condition was obtained at pH 4 and 50°C which was pretreated at 100°C using 1.5% acid concentration. Copyright © 2012 by BCREC UNDIP. All rights reserved. (Selected Paper from International Conference on Chemical and Material Engineering (ICCME 2012Received: 28th September 2012, Revised: 2nd October 2012, Accepted: 4th October 2012[How to Cite: R. Agustriyanto, A. Fatmawati, Y. Liasari. (2012. Study of Enzymatic Hydrolysis of Dilute Acid Pretreated Coconut Husk. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 137-141. doi:10.9767/bcrec.7.2.4046.137-141] [How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.4046.137-141 ] | View in 

Extraction of gold(III) from hydrochloric acid solutions by CTAB/n-heptane/iso-amyl alcohol/Na{sub 2}SO{sub 3} microemulsion

Energy Technology Data Exchange (ETDEWEB)

Lu Wenjuan; Lu Yanmin; Liu Fei; Shang Kai; Wang Wei [Key Laboratory for Special Functional Aggregated Materials of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Yang Yanzhao, E-mail: yzhyang@sdu.edu.cn [Key Laboratory for Special Functional Aggregated Materials of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

2011-02-28

The extraction of Au(III) from hydrochloric acid solutions by microemulsion was studied. The extraction experiments were carried out using cetyltrimethylammonium bromide (CTAB) as surfactant and iso-amyl alcohol as co-surfactant. Au(III) was found to be extracted into the microemulsion phase due to ion pair formation such as AuCl{sub 4}{sup -}CTAB{sup +}. The influence of temperature on the extraction of Au(III) has been investigated at temperatures ranging from 288 to 313 K. Temperature was found to decrease the distribution of Au(III). Thermodynamic parameters like enthalpy and entropy of the extraction, calculated by applying Van't Hoff equation, were -36.76 kJ mol{sup -1} and -84.87 J mol{sup -1} K{sup -1}, respectively. Furthermore, the influence of the concentrations of hydrogen ion and chloride anion on the extraction efficiency (E%) were verified. Au(III) was extracted quantitatively (E% > 99%) and selectively at the whole range of HCl concentrations (0.2-5 M). Recovery of gold from electrical waste and treatment of CTAB wastewater generated from the extraction were also discussed. Thus, the extraction of Au(III) from hydrochloric acid solutions by microemulsion is an effective approach.

A simple procedure for preparing chitin oligomers through acetone precipitation after hydrolysis in concentrated hydrochloric acid.

Science.gov (United States)

Kazami, Nao; Sakaguchi, Masayoshi; Mizutani, Daisuke; Masuda, Tatsuhiko; Wakita, Satoshi; Oyama, Fumitaka; Kawakita, Masao; Sugahara, Yasusato

2015-11-05

Chitin oligomers are of interest because of their numerous biologically relevant properties. To prepare chitin oligomers containing 4-6 GlcNAc units [(GlcNAc)4-6], α- and β-chitin were hydrolyzed with concentrated hydrochloric acid at 40 °C. The reactant was mixed with acetone to recover the acetone-insoluble material, and (GlcNAc)4-6 was efficiently recovered after subsequent water extraction. Composition analysis using gel permeation chromatography and MALDI-TOF mass spectrometry indicated that (GlcNAc)4-6 could be isolated from the acetone-insoluble material with recoveries of approximately 17% and 21% from the starting α-chitin and β-chitin, respectively. The acetone precipitation method is highly useful for recovering chitin oligomers from the acid hydrolysate of chitin. The changes in the molecular size and higher-order structure of chitin during the course of hydrolysis were also analyzed, and a model that explains the process of oligomer accumulation is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Inhibitive Action Of Sodium Soya Sulphonate Towards The Corrosion Of Aluminium In Hydrochloric Acid

OpenAIRE

Mourad, M. Y.; Mead, A. I.; Seliman, S. A.

1993-01-01

The dissolution of aluminium in 2M hydrochloric acid in the presence of sodium soya sulphonate (SSS) as corrosion inhibitor has been studied using hydrogen evolution and thermometric methods. The two methods gave consistent results. The results obtained indicate that the inhibitive effect of the sulphonated mixture relates to chemisorption mechanism on the metal surface via the n electrons in the double bonds. تمت دراسة ذوبان الألمونيوم في محلول 2 مولارى من حمض الهيدروكلوريك في وجود سلفونا...

Ion exchange separation of carrier-free 140Ba and 140La from their equilibrium mixture using nitrilotriacetic acid and ascorbic acid as eluents

International Nuclear Information System (INIS)

Das, N.R.; Bhattacharyya, S.N.

1982-01-01

A simple cation exchange procedure for separation of 140 Ba- 140 La using Dowex 50W-X8 and nitrilotriacetic acid or ascorbic acid as the eluent has been described. The optimal separation of the daughter from the parent has been achieved using a 4% Na-nitrilotriacetate or Na-ascorbate solution at pH 7. The parent, 140 Ba, left in the column can be eluted with dilute hydrochloric acid or it can be retained in the column for milking off the daughter, 140 La, when needed. The radiochemical purity of the separated isotopes, 140 Ba and 140 La, were verified by γ-ray spectrometry. (author)

Laboratory studies of 2H evaporator scale dissolution in dilute nitric acid

International Nuclear Information System (INIS)

Oji, L.

2014-01-01

The rate of 2H evaporator scale solids dissolution in dilute nitric acid has been experimentally evaluated under laboratory conditions in the SRNL shielded cells. The 2H scale sample used for the dissolution study came from the bottom of the evaporator cone section and the wall section of the evaporator cone. The accumulation rate of aluminum and silicon, assumed to be the two principal elemental constituents of the 2H evaporator scale aluminosilicate mineral, were monitored in solution. Aluminum and silicon concentration changes, with heating time at a constant oven temperature of 90 deg C, were used to ascertain the extent of dissolution of the 2H evaporator scale mineral. The 2H evaporator scale solids, assumed to be composed of mostly aluminosilicate mineral, readily dissolves in 1.5 and 1.25 M dilute nitric acid solutions yielding principal elemental components of aluminum and silicon in solution. The 2H scale dissolution rate constant, based on aluminum accumulation in 1.5 and 1.25 M dilute nitric acid solution are, respectively, 9.21E-04 ± 6.39E-04 min -1 and 1.07E-03 ± 7.51E-05 min -1 . Silicon accumulation rate in solution does track the aluminum accumulation profile during the first few minutes of scale dissolution. It however diverges towards the end of the scale dissolution. This divergence therefore means the aluminum-to-silicon ratio in the first phase of the scale dissolution (non-steady state conditions) is different from the ratio towards the end of the scale dissolution. Possible causes of this change in silicon accumulation in solution as the scale dissolution progresses may include silicon precipitation from solution or the 2H evaporator scale is a heterogeneous mixture of aluminosilicate minerals with several impurities. The average half-life for the decomposition of the 2H evaporator scale mineral in 1.5 M nitric acid is 12.5 hours, while the half-life for the decomposition of the 2H evaporator scale in 1.25 M nitric acid is 10.8 hours

Effect of temperature on the dilution enthalpies of α,ω-amino acids in aqueous solutions

International Nuclear Information System (INIS)

Romero, C.M.; Cadena, J.C.; Lamprecht, I.

2011-01-01

Highlights: → The dilution of 3-amino propanoic acid, 4-amino butanoic acid, 5-amino pentanoic acid, and 6-amino hexanoic acid in water is an exothermic process at T = (293.15, 298.15, 303.15, and 308.15) K. → The limiting experimental slopes of the enthalpies of dilution with respect to the molality change Δm, are negative suggesting that the solutes interact with water primarily through their alkyl groups. → The value of the pairwise coefficient is positive at the temperatures considered, and the magnitude increases linearly with the number of methylene groups. → The comparison between the pairwise interaction coefficients for α,ω-amino acids and α-amino acids shows that the change in the enthalpic interaction coefficient is related to the relative position of the polar groups. - Abstract: Dilution enthalpies of aqueous solutions of 3-amino propanoic acid, 4-amino butanoic acid, 5-amino pentanoic acid, and 6-amino hexanoic acid were determined at T = (293.15, 298.15, 303.15, and 308.15) K using an LKB flow microcalorimeter. The homotactic interaction coefficients were obtained according to the McMillan-Mayer theory from the experimental data. For all the systems studied, the dilution of α,ω-amino acids in water is an exothermic process; the pair coefficients have positive values which increases with chain length. The obtained values of the interaction coefficients are interpreted in terms of solute-solvent and solute-solute interactions and are used as indicative of hydrophobic behavior of the amino acid studied.

Benzaldehyde, 2-hydroxybenzoyl hydrazone derivatives as inhibitors of the corrosion of aluminium in hydrochloric acid.

Science.gov (United States)

Fouda, A S; Gouda, M M; El-Rahman, S I

2000-05-01

The effect of benzaldehyde, 2-hydroxybenzoyl hydrazone derivatives on the corrosion of aluminium in hydrochloric acid has been investigated using thermometric and polarization techniques. The inhibitive efficiency ranking of these compounds from both techniques was found to be: 2>3>1>4. The inhibitors acted as mixed-type inhibitors but the cathode is more polarized. The relative inhibitive efficiency of these compounds has been explained on the basis of structure of the inhibitors and their mode of interaction at the surface. Results show that these additives are adsorbed on an aluminium surface according to the Langmuir isotherm. Polarization measurements indicated that the rate of corrosion of aluminium rapidly increases with temperature over the range 30-55 degrees C both in the absence and in the presence of inhibitors. Some thermodynamic data of the adsorption process are calculated and discussed.

Activation of Graphene Oxide with Hydrochloric Acid for Nitrate Removal from Aqueous Solutions

Directory of Open Access Journals (Sweden)

Abolghasem Alighardashi

2017-11-01

Full Text Available Long-term drinking of nitrate-contaminated water poses a serious risk to human health. The present study explores the possibility of enhancing the adsorption capacity of graphene oxide via activation with hydrochloric acid for nitrate removal from aqueous solutions. Experiments were performed in a batch reactor in which such major factors as pH, reaction time, and concentrations of both graphene oxide (GO and activated graphene oxide (AGO were used as variables. Nitrate removal efficiency was investigated using the One-Way ANOVA statistical test and SPSS-16 software. The chemical composition and solid structure of the synthesized AGO were analyzed using FE-SEM coupled with energy dispersive spectrometry (EDS. The micropore volumes of the samples were determined using the BET and BJH. The predominant composition (52% of the synthesized AGO was C and its mean pore diameter was 26.896 nm. The maximum adsorption capacity of AGO was estimated at 3333.33 mg/g. Based on the results, the AGO nano-structure may be recomended as a new means for nitrate removal from aqueous solutions.

Characterization of the Unusual Product from the Reaction between Cobalt(II) Chloride, Ethane-1,2-diamine, and Hydrochloric Acid: An Undergraduate Project Involving an Unknown Metal Complex.

Science.gov (United States)

Curtis, Neil F.; And Others

1986-01-01

Discusses the need for student research-type chemistry projects based upon "unknown" metal complexes. Describes an experiment involving the product from the reaction between cobalt(II) chloride, ethane-1,2-diamine (en) and concentrated hydrochloric acid. Outlines the preparation of the cobalt complex, along with procedure, results and…

Surface chemical compositions and dispersity of starch nanocrystals formed by sulfuric and hydrochloric acid hydrolysis.

Science.gov (United States)

Wei, Benxi; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

2014-01-01

Surface chemical compositions of starch nanocrystals (SNC) prepared using sulfuric acid (H2SO4) and hydrochloric acid (HCl) hydrolysis were analyzed by X-ray photoelectron spectroscopy (XPS) and FT-IR. The results showed that carboxyl groups and sulfate esters were presented in SNC after hydrolysis with H2SO4, while no sulfate esters were detected in SNC during HCl-hydrolysis. TEM results showed that, compared to H2SO4-hydrolyzed sample, a wider size distribution of SNC prepared by HCl-hydrolysis were observed. Zeta-potentials were -23.1 and -5.02 mV for H2SO4- and HCl-hydrolyzed SNC suspensions at pH 6.5, respectively. Nevertheless, the zeta-potential values decreased to -32.3 and -10.2 mV as the dispersion pH was adjusted to 10.6. After placed 48 h at pH 10.6, zeta-potential increased to -24.1 mV for H2SO4-hydrolyzed SNC, while no change was detected for HCl-hydrolyzed one. The higher zeta-potential and relative small particle distribution of SNC caused more stable suspensions compared to HCl-hydrolyzed sample.

Surface chemical compositions and dispersity of starch nanocrystals formed by sulfuric and hydrochloric acid hydrolysis.

Directory of Open Access Journals (Sweden)

Benxi Wei

Full Text Available Surface chemical compositions of starch nanocrystals (SNC prepared using sulfuric acid (H2SO4 and hydrochloric acid (HCl hydrolysis were analyzed by X-ray photoelectron spectroscopy (XPS and FT-IR. The results showed that carboxyl groups and sulfate esters were presented in SNC after hydrolysis with H2SO4, while no sulfate esters were detected in SNC during HCl-hydrolysis. TEM results showed that, compared to H2SO4-hydrolyzed sample, a wider size distribution of SNC prepared by HCl-hydrolysis were observed. Zeta-potentials were -23.1 and -5.02 mV for H2SO4- and HCl-hydrolyzed SNC suspensions at pH 6.5, respectively. Nevertheless, the zeta-potential values decreased to -32.3 and -10.2 mV as the dispersion pH was adjusted to 10.6. After placed 48 h at pH 10.6, zeta-potential increased to -24.1 mV for H2SO4-hydrolyzed SNC, while no change was detected for HCl-hydrolyzed one. The higher zeta-potential and relative small particle distribution of SNC caused more stable suspensions compared to HCl-hydrolyzed sample.

Surface Chemical Compositions and Dispersity of Starch Nanocrystals Formed by Sulfuric and Hydrochloric Acid Hydrolysis

Science.gov (United States)

Wei, Benxi; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

2014-01-01

Surface chemical compositions of starch nanocrystals (SNC) prepared using sulfuric acid (H2SO4) and hydrochloric acid (HCl) hydrolysis were analyzed by X-ray photoelectron spectroscopy (XPS) and FT-IR. The results showed that carboxyl groups and sulfate esters were presented in SNC after hydrolysis with H2SO4, while no sulfate esters were detected in SNC during HCl-hydrolysis. TEM results showed that, compared to H2SO4-hydrolyzed sample, a wider size distribution of SNC prepared by HCl-hydrolysis were observed. Zeta-potentials were −23.1 and −5.02 mV for H2SO4- and HCl-hydrolyzed SNC suspensions at pH 6.5, respectively. Nevertheless, the zeta-potential values decreased to −32.3 and −10.2 mV as the dispersion pH was adjusted to 10.6. After placed 48 h at pH 10.6, zeta-potential increased to −24.1 mV for H2SO4-hydrolyzed SNC, while no change was detected for HCl-hydrolyzed one. The higher zeta-potential and relative small particle distribution of SNC caused more stable suspensions compared to HCl-hydrolyzed sample. PMID:24586246

Direct anodic hydrochloric acid and cathodic caustic production during water electrolysis

Science.gov (United States)

Lin, Hui-Wen; Cejudo-Marín, Rocío; Jeremiasse, Adriaan W.; Rabaey, Korneel; Yuan, Zhiguo; Pikaar, Ilje

2016-02-01

Hydrochloric acid (HCl) and caustic (NaOH) are among the most widely used chemicals by the water industry. Direct anodic electrochemical HCl production by water electrolysis has not been successful as current commercially available electrodes are prone to chlorine formation. This study presents an innovative technology simultaneously generating HCl and NaOH from NaCl using a Mn0.84Mo0.16O2.23 oxygen evolution electrode during water electrolysis. The results showed that protons could be anodically generated at a high Coulombic efficiency (i.e. ≥ 95%) with chlorine formation accounting for 3 ~ 5% of the charge supplied. HCl was anodically produced at moderate strengths at a CE of 65 ± 4% together with a CE of 89 ± 1% for cathodic caustic production. The reduction in CE for HCl generation was caused by proton cross-over from the anode to the middle compartment. Overall, this study showed the potential of simultaneous HCl and NaOH generation from NaCl and represents a major step forward for the water industry towards on-site production of HCl and NaOH. In this study, artificial brine was used as a source of sodium and chloride ions. In theory, artificial brine could be replaced by saline waste streams such as Reverse Osmosis Concentrate (ROC), turning ROC into a valuable resource.

Elucidating the role of ferrous ion cocatalyst in enhancing dilute acid pretreatment of lignocellulosic biomass

Directory of Open Access Journals (Sweden)

Wei Hui

2011-11-01

Full Text Available Abstract Background Recently developed iron cocatalyst enhancement of dilute acid pretreatment of biomass is a promising approach for enhancing sugar release from recalcitrant lignocellulosic biomass. However, very little is known about the underlying mechanisms of this enhancement. In the current study, our aim was to identify several essential factors that contribute to ferrous ion-enhanced efficiency during dilute acid pretreatment of biomass and to initiate the investigation of the mechanisms that result in this enhancement. Results During dilute acid and ferrous ion cocatalyst pretreatments, we observed concomitant increases in solubilized sugars in the hydrolysate and reducing sugars in the (insoluble biomass residues. We also observed enhancements in sugar release during subsequent enzymatic saccharification of iron cocatalyst-pretreated biomass. Fourier transform Raman spectroscopy showed that major peaks representing the C-O-C and C-H bonds in cellulose are significantly attenuated by iron cocatalyst pretreatment. Imaging using Prussian blue staining indicated that Fe2+ ions associate with both cellulose/xylan and lignin in untreated as well as dilute acid/Fe2+ ion-pretreated corn stover samples. Analyses by scanning electron microscopy and transmission electron microscopy revealed structural details of biomass after dilute acid/Fe2+ ion pretreatment, in which delamination and fibrillation of the cell wall were observed. Conclusions By using this multimodal approach, we have revealed that (1 acid-ferrous ion-assisted pretreatment increases solubilization and enzymatic digestion of both cellulose and xylan to monomers and (2 this pretreatment likely targets multiple chemistries in plant cell wall polymer networks, including those represented by the C-O-C and C-H bonds in cellulose.

Dilute oxalic acid pretreatment for biorefining giant reed (Arundo donax L.)

Science.gov (United States)

Danilo Scordia; Salvatore L. Cosentino; Jae-Won Lee; Thomas W. Jeffries

2011-01-01

Biomass pretreatment is essential to overcome recalcitrance of lignocellulose for ethanol production. In the present study we pretreated giant reed (Arundo donax L.), a perennial, rhizomatous lignocellulosic grass with dilute oxalic acid. The effects of temperature (170-190 ºC), acid loading (2-10% w/w) and reaction time (15-40 min) were handled as a single...

Rinsing with antacid suspension reduces hydrochloric acid-induced erosion.

Science.gov (United States)

Alves, Maria do Socorro Coelho; Mantilla, Taís Fonseca; Bridi, Enrico Coser; Basting, Roberta Tarkany; França, Fabiana Mantovani Gomes; Amaral, Flávia Lucisano Botelho; Turssi, Cecilia Pedroso

2016-01-01

Mouthrinsing with antacids, following erosive episodes, have been suggested as a preventative strategy to minimize tooth surface loss due to their neutralizing effect. The purpose of this in situ study was to evaluate the effect of an antacid suspension containing sodium alginate, sodium bicarbonate and calcium carbonate in controlling simulated erosion of enamel of intrinsic origin. The experimental units were 48 slabs (3×3×2mm) of bovine enamel, randomly divided among 12 volunteers who wore palatal appliances with two enamel slabs. One of them was exposed extra-orally twice a day to 25mL of a hydrochloric acid (HCl) solution (0.01M, pH 2) for 2min. There were two independent phases, lasting 5 days each. In the first phase, according to a random scheme, half of the participants rinsed with 10mL of antacid suspension (Gaviscon(®), Reckitt Benckiser Healthcare Ltd.), while the remainder was rinsed with deionized water, for 1min. For the second phase, new slabs were inserted and participants switched to the treatment not received in the first stage. Therefore, the groups were as follows: (a) erosive challenge with HCl+antacid suspension; (b) erosive challenge with HCl+deionized water (DIW); (c) no erosive challenge+antacid suspension; (d) no erosive challenge+DIW. Specimens were assessed in terms of surface loss using optical profilometry and Knoop microhardness. The data were analyzed using repeated measures two-way analysis of variance and Tukey's tests. Compared to DIW rinses, surface loss of enamel was significantly lower when using an antacid rinse following erosive challenges (p=0.015). The Knoop microhardness of the enamel was significantly higher when the antacid rinse was used (p=0.026). The antacid suspension containing sodium alginate, sodium bicarbonate and calcium carbonate, rinsed after erosive challenges of intrinsic origin, reduced enamel surface loss. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effect of dilute acid pre-treatment process in bioethanol production from durian (Durio zibethinus) seeds waste

Science.gov (United States)

Ghazali, K. A.; Salleh, S. F.; Riayatsyah, T. M. I.; Aditiya, H. B.; Mahlia, T. M. I.

2016-03-01

Lignocellulosic biomass is one of the promising feedstocks for bioethanol production. The process starts from pre-treatment, hydrolysis, fermentation, distillation and finally obtaining the final product, ethanol. The efficiency of enzymatic hydrolysis of cellulosic biomass depends heavily on the effectiveness of the pre-treatment step which main function is to break the lignin structure of the biomass. This work aims to investigate the effects of dilute acid pre-treatment on the enzymatic hydrolysis of durian seeds waste to glucose and the subsequent bioethanol fermentation process. The yield of glucose from dilute acid pre-treated sample using 0.6% H2SO4 and 5% substrate concentration shows significant value of 23.4951 g/L. Combination of dilute acid pre-treatment and enzymatic hydrolysis using 150U of enzyme able to yield 50.0944 g/L of glucose content higher compared to normal pre-treated sample of 8.1093 g/L. Dilute acid pre-treatment sample also shows stable and efficient yeast activity during fermentation process with lowest glucose content at 2.9636 g/L compared to 14.7583g/L for normal pre-treated sample. Based on the result, it can be concluded that dilute acid pre-treatment increase the yield of ethanol from bioethanol production process.

Molecular and crystal structures of the products of crystallization of (N'-furfurylidene)isonicotinoylhydrazide from aqueous solutions of hydrochloric and acetic acids

International Nuclear Information System (INIS)

Chuev, I.I.; Nikonova, L.A.; Atovmyan, E.G.; Utenyshev, A.N.; Aldoshin, S.M.

2001-01-01

Crystals of (N ' -furfurylidene)isonicotinoylhydrazide (I), which have been isolated from a water-methanol solution of hydrochloric acid (Ia) and an aqueous solution (∼50%) of acetic acid (Ib), are studied by X-ray diffraction. In Ia, the nitrogen atom of the pyridine ring is protonated. In the crystal, the intermolecular C=O···HN(Py) hydrogen bonds link the I · H + cations into chains which are bound through centrosymmetric NH···W···Cl - ···W ' ···H ' N ' bridges. In molecule Ib, no protonation occurs; however, its pyridine N atom is blocked by the hydroxyl H atom of a solvate molecule of acetic acid. Crystals Ib have a layered structure. The crystallization water molecule is involved in the formation of three intermolecular hydrogen bonds, namely, those with the H atom of the amide group and the carbonyl O atoms of molecule I and an acetic acid molecule of the neighboring layer

Investigation of the oxidation states of Pu isotopes in a hydrochloric acid solution

Energy Technology Data Exchange (ETDEWEB)

Lee, M.H. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)], E-mail: mhlee@kaeri.re.kr; Kim, J.Y.; Kim, W.H.; Jung, E.C.; Jee, K.Y. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)

2008-12-15

The characteristics of the oxidation states of Pu in a hydrochloric acid solution were investigated and the results were applied to a separating of Pu isotopes from IAEA reference soils. The oxidation states of Pu(III) and Pu(IV) were prepared by adding hydroxylamine hydrochloride and sodium nitrite to a Pu stock solution, respectively. Also, the oxidation state of Pu(VI) was adjusted with concentrated HNO{sub 3} and HClO{sub 4}. The stability of the various oxidation states of plutonium in a HCl solution with elapsed time after preparation were found to be in the following order: Pu(III){approx}Pu(VI)>Pu(IV)>Pu(V). The chemical recoveries of Pu(IV) in a 9 M HCl solution with an anion exchange resin were similar to those of Pu(VI). This method for the determination of Pu isotopes with an anion exchange resin in a 9 M HCl medium was applied to IAEA reference soils where the activity concentrations of {sup 239,240}Pu and {sup 238}Pu in IAEA-375 and IAEA-326 were consistent with the reference values reported by the IAEA.

Corrosion Behavior of Ni3(Si,Ti + 2Mo in Hydrochloric Acid Solution

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2013-10-01

Full Text Available The corrosion behavior of Ni3(Si,Ti + 2Mo intermetallic compound (L12 and (L12 + Niss mixture region has been investigated using an immersion test, polarization method and surface analytical method (scanning electron microscope and energy-dispersive X-Ray spectrometry in 0.5 kmol/m3 hydrochloric acid (HCl solution at 303 K.  In addition, the results obtained were compared to those of the L12 single-phase Ni3(Si,Ti intermetallic compound and C 276 alloy.  It was found that Ni3(Si,Ti + 2Mo had the preferential dissolution of L12 with a lower Mo concentration compared to (L12 + Niss mixture region.  From the immersion test and polarization curves, Ni3(Si,Ti + 2Mo and C276 showed the lowest corrosion resistance and the highest corrosion resistance in the solution, respectively.  From this work, It implied that unlike C276, Ni3(Si,Ti +2Mo intermetallic compound was difficult to form a stable passive film in HCl solution as well as Ni3(Si,Ti in the same solution.

Densities, molar volumes, and isobaric expansivities of (d-xylose+hydrochloric acid+water) systems

International Nuclear Information System (INIS)

Zhang Qiufen; Yan Zhenning; Wang Jianji; Zhang Hucheng

2006-01-01

Densities of (d-xylose+HCl+water) have been measured at temperature in the range (278.15 to 318.15) K as a function of concentration of both d-xylose and hydrochloric acid. The densities have been used to estimate the molar volumes and isobaric expansivity of the ternary solutions. The molar volumes of the ternary solutions vary linearly with mole fraction of d-xylose. The standard partial molar volumes V 2,φ - bar for d-xylose in aqueous solutions of molality (0.2, 0.4, 0.7, 1.1, 1.6, and 2.1) mol.kg -1 HCl have been determined. In the investigated temperature range, the relation: V 2,φ - bar =c 1 +c 2 {(T/K)-273.15} 1/2 , can be used to describe the temperature dependence of the standard partial molar volumes. These results have, in conjunction with the results obtained in water, been used to deduce the standard volumes of transfer, Δ t V - bar , of d-xylose from water to aqueous HCl solutions. An increase in the transfer volume of d-xylose with increasing HCl concentrations has been explained by the stronger interactions of H + with the hydrophilic groups of d-xylose

Inhibition of the corrosion of mild steel in hydrochloric acid by isatin and isatin glycine

Directory of Open Access Journals (Sweden)

B.I. Ita

2006-12-01

Full Text Available The inhibition of corrosion of mild steel in hydrochloric acid by isatin glycine (ING and isatin (IN at 30-60 oC and concentrations of 0.0001 M to 0.0005 M was studied via weight loss method. At the highest inhibitor concentration studied ING exhibited inhibition efficiency of 87% while IN exhibited 84% at 60 oC. A chemical adsorption mechanism was proposed on the basis of the temperature effect and obtained average activation energy values of 143.9 kJ/mol for ING and 118.5 kJ/mol for IN. The two inhibitors were confirmed to obey the Langmuir adsorption isotherm equation at the concentrations studied. Also a first-order type of mechanism was proposed from the kinetic treatment of the result. The difference in the inhibitory properties of the inhibitors was explained in terms of the difference in their molecular structures and solubility rather than difference in molecular weights alone.

Enzymatic saccharification of dilute acid pretreated saline crops for fermentable sugar production

Energy Technology Data Exchange (ETDEWEB)

Zheng, Yi; Zhang, Ruihong [Biological and Agricultural Engineering Department, University of California, Davis One Shields Avenue, Davis, CA 95616 (United States); Pan, Zhongli [Biological and Agricultural Engineering Department, University of California, Davis One Shields Avenue, Davis, CA 95616 (United States); Processed Foods Research Unit, USDA-ARS-WRRC, 800 Buchanan Street, Albany, CA 94710 (United States); Wang, Donghai [Biological and Agricultural Engineering Department, Kansas State University, Manhattan, KS 66506 (United States)

2009-11-15

Four saline crops [athel (Tamarix aphylla L), eucalyptus (Eucalyptus camaldulensis), Jose Tall Wheatgrass (Agropyron elongatum), and Creeping Wild Ryegrass (Leymus triticoides)] that are used in farms for salt uptake from soil and drainage irrigation water have the potential for fuel ethanol production because they don't take a large number of arable lands. Dilute sulfuric acid pretreatment and enzymatic hydrolysis were conducted to select the optimum pretreatment conditions and the best saline crop for further enzymatic hydrolysis research. The optimum dilute acid pretreatment conditions included T = 165 C, t = 8 min, and sulfuric acid concentration 1.4% (w/w). Creeping Wild Ryegrass was decided to be the best saline crop. Solid loading, cellulase and {beta}-glucosidase concentrations had significant effects on the enzymatic hydrolysis of dilute acid pretreated Creeping Wild Ryegrass. Glucose concentration increased by 36 mg/mL and enzymatic digestibility decreased by 20% when the solid loading increased from 4 to 12%. With 8% solid loading, enzymatic digestibility increased by over 30% with the increase of cellulase concentration from 5 to 15 FPU/g-cellulose. Under given cellulase concentration of 15 FPU/g-cellulose, 60% increase of enzymatic digestibility of pretreated Creeping Wild Ryegrass was obtained with the increase of {beta}-glucosidase concentration up to 15 CBU/g-cellulose. With a high solid loading of 10%, fed-batch operation generated 12% and 18% higher enzymatic digestibility and glucose concentration, respectively, than batch process. (author)

Interaction between amylose and 1-butanol during 1-butanol-hydrochloric acid hydrolysis of normal rice starch.

Science.gov (United States)

Hu, Xiuting; Wei, Benxi; Zhang, Bao; Li, Hongyan; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

2013-10-01

The aim of this study was to examine the interaction between amylose and 1-butanol during the 1-butanol-hydrochloric acid (1-butanol-HCl) hydrolysis of normal rice starch. The interaction model between amylose and 1-butanol was proposed using gas chromatography-mass spectrometry (GC-MS), (13)C cross polarization and magic angle spinning NMR analysis ((13)C CP/MAS NMR), differential scanning calorimetry (DSC), and thermalgravimetric analysis (TGA). GC-MS data showed that another form of 1-butanol existed in 1-butanol-HCl-hydrolyzed normal rice starch, except in the form of free molecules absorbed on the starch granules. The signal of 1-butanol-HCl-hydrolyzed starch at 100.1 ppm appeared in the (13)C CP/MAS NMR spectrum, indicating that the amylose-1-butanol complex was formed. DSC and TGA data also demonstrated the formation of the complex, which significantly affected the thermal properties of normal rice starch. These findings revealed that less dextrin with low molecular weight formed might be attributed to resistance of this complex to acid during 1-butanol-HCl hydrolysis. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Study on tea leaves extract as green corrosion inhibitor of mild steel in hydrochloric acid solution

Science.gov (United States)

Hamdan, A. B.; Suryanto; Haider, F. I.

2018-01-01

Corrosion inhibitor from extraction of plant has been considered as the most preferable and most chosen technique to prevent corrosion of metal in acidic medium because of the environmental friendly factor. In this study, black tea leaves extraction was tested as corrosion inhibitor for mild steel in 0.1M of hydrochloric acid (HCl) with the absence and presence of corrosion inhibitor. The efficiency and effectiveness of black tea as corrosion inhibitor was tested by using corrosion weight loss measurement experiment was carried out with varies parameters which with different concentration of black tea extract solution. The extraction of black tea solution was done by using aqueous solvent method. The FT-IR result shows that black tea extract containing compounds such as catechin, caffeine and tannins that act as anti-corrosive reagents and responsible to enhance the effectiveness of black tea extract as corrosion inhibitor by forming the hydrophobic thin film through absorption process. As a result of weight loss measurement, it shows that loss in weight of mild steel reduces as the concentration of inhibitor increases. The surface analysis was done on the mild steel samples by using SEM.

Study and characterization of powder mackerel (Scomberomorus commerson) bone gelatin through hydrolysis of hydrochloric acid

Science.gov (United States)

Mardawati, E.; Sugandi, H.; Kayaputri, I. L.; Cahyana, Y.; Wira, D. W.; Pujianto, T.; Kastaman, R.

2018-02-01

Gelatin is one of the most common food additives in the food and beverage industry. Gelatin is generally made of leather or pig bones, causing concerns about the halal and safety of its product. Mackerel fish bone (Scomberomorus commerson) is a waste fish that has not been utilized well and it contains 18.6% of collagen so that it can be made into gelatin. The purpose of this research is to know the relation between HCl concentration with physical and chemical characteristics of gelatin and to know the best HCl concentration for gelatin production. Based on the physical and chemical analysis of gelatin, it is known that the concentration of hydrochloric acid influences the yield, viscosity, gel strength and pH produced. The higher HCl concentration there will be decrease in the pH value, gel strength, viscosity and protein. The yield will rise to the optimum point then decrease with respect to the high HCl concentration. Gelatin with 2% HCl concentration was the best treatment, with pH value 3.83, viscosity 3.65cP, gel strength 190.50 blooms which fulfilled British Standard, yield 10.16%, protein content 43.34%. It has functional group such as amino acids glycine, proline and hydroxyproline and 15 other amino acids, the gelatin group uptake in the region of amide wave numbers A, amides I, II and III, with a gelatin molecular weight of 290.35 g/mol.

Conversion of rice straw to sugars by dilute-acid hydrolysis

International Nuclear Information System (INIS)

Karimi, Keikhosro; Kheradmandinia, Shauker; Taherzadeh, Mohammad J.

2006-01-01

Hydrolysis of rice straw by dilute sulfuric acid at high temperature and pressure was investigated in one and two stages. The hydrolyses were carried out in a 10-l reactor, where the hydrolysis retention time (3-10 min), pressure (10-35 bar) and acid concentration (0-1%) were examined. Optimization of first stage hydrolysis is desirable to achieve the highest yield of the sugars from hemicellulose and also as a pretreatment for enzymatic hydrolysis. The results show the ability of first stage hydrolysis to depolymerize xylan to xylose with a maximum yield of 80.8% at hydrolysis pressure of 15 bar, 10 min retention time and 0.5% acid concentration. However, the yield of glucose from glucan was relatively low in first stage hydrolysis at a maximum of 25.8%. The solid residuals were subjected to further dilute-acid hydrolysis in this study. This second-stage hydrolysis without addition of the acid could not increase the yield of glucose from glucan beyond 26.6%. On the other hand, the best results of the hydrolysis were achieved, when 0.5% sulfuric acid was added prior to each stage in two-stage hydrolysis. The best results of the second stage of the hydrolysis were achieved at the hydrolysis pressure and the retention time of 30 bar and 3 min in the second stage hydrolysis, where a total of 78.9% of xylan and 46.6% of glucan were converted to xylose and glucose, respectively in the two stages. Formation of furfural and HMF were functions of the hydrolysis pressure, acid concentration, and retention time, whereas the concentration of acetic acid was almost constant at pressure of higher than 10 bar and a total retention time of 10 min

Response of citrus and other selected plant species to simulated HCL - acid rain

Science.gov (United States)

Knott, W. M.; Heagle, A. S.

1980-01-01

Mature valencia orange trees were sprayed with hydrochloric acid solutions (pH 7.8, 2.0, 1.0, and 0.5) in the field at the full bloom stage and at one month after fruit set. Potted valencia orange and dwarf citrus trees, four species of plants native to Merritt Island, and four agronomic species were exposed to various pH levels of simulated acid rain under controlled conditions. The acid rain was generated from dilutions of hydrochloric acid solutions or by passing water through an exhaust generated by burning solid rocket fuel. The plants were injured severely at pH levels below 1.0, but showed only slight injury at pH levels of 2.0 and above. Threshold injury levels were between 2.0 and 3.0 pH. The sensitivity of the different plant species to acid solutions was similar. Foliar injury symptoms were representative of acid rain including necrosis of young tissue, isolated necrotic spots or patches, and leaf abscission. Mature valencia orange trees sprayed with concentrations of 1.0 pH and 0.5 pH in the field had reduced fruit yields for two harvests after the treatment. All experimental trees were back to full productivity by the third harvest after treatment.

Kinetic study of dilute nitric acid treatment of corn stover at relatively high temperature

Energy Technology Data Exchange (ETDEWEB)

Zhang, R.; Lu, X.; Liu, Y.; Wang, X.; Zhang, S. [Tianjin University, School of Environmental Science and Technology, Tianjin (China)

2011-03-15

Corn stover was hydrolyzed using dilute nitric acid at 150 C. Several concentrations of HNO{sub 3} (0.2, 0.4 and 0.6 wt-%) and reaction times (0-60 min) were evaluated. The kinetic parameters of mathematical models for predicting the concentrations of xylose, glucose, arabinose, acetic acid, and furfural in the hydrolysates were determined. The hydrolysates obtained from corn stover can be used to produce methane by an anaerobic fermentation process. Thus, the hydrolysis process of corn stover using dilute nitric acid can be conceived as the first stage of an integrated strategy for corn stover utilization. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Separation of uranium and other metals from commercial phosphoric acid by ion-exchange and voltammetric determination of uranium

International Nuclear Information System (INIS)

Ferreira, J.B.C.; Carvalho, F.M.S. de; Abrao, A.

1985-11-01

The separation of metals from crude commercial phosphoric acid is achieved by simple dilution and percolation through a strong cationic ion exchanger. Uranium, calcium, magnesium, manganese, iron and aluminum are quantitatively fixed by the exchanger and can be detected or analysed after their complete elution with 6 M HCI. Titanium and zirconium are only partially retained. Specially for its separation and determination uranium is retained selectively by the resin from the phosphoric acid-EDTA solution, the column is washed with water and then eluted with hydrochloric acid. Uranium is analyzed by voltametry with the hanging drop mercury electrode. (Author) [pt

Determination of uranium isotopes in environmental samples by anion exchange in sulfuric and hydrochloric acid media

International Nuclear Information System (INIS)

Popov, L.

2016-01-01

Method for determination of uranium isotopes in various environmental samples is presented. The major advantages of the method are the low cost of the analysis, high radiochemical yields and good decontamination factors from the matrix elements, natural and man-made radionuclides. The separation and purification of uranium is attained by adsorption with strong base anion exchange resin in sulfuric and hydrochloric acid media. Uranium is electrodeposited on a stainless steel disk and measured by alpha spectrometry. The analytical method has been applied for the determination of concentrations of uranium isotopes in mineral, spring and tap waters from Bulgaria. The analytical quality was checked by analyzing reference materials. - Highlights: • The method allows cost-effective determination of U isotopes. • High amounts of environmental samples can be analyzed. • High chemical yields, energy resolution and decontamination factors were achieved. • Uranium isotope concentrations in mineral waters from Bulgaria are presented.

CORROSION INHIBITIVE PROPERTIES OF EXTRACT OF JATROPHA CURCAS LEAVES ON MILD STEEL IN HYDROCHLORIC ACID ENVIRONMENT

Directory of Open Access Journals (Sweden)

J. Odusote

2016-09-01

Full Text Available Jatropha curcas leaves extract was tested as a green corrosion inhibitor for mild steel in aqueous hydrochloric acid solution using gravimetric and thermometric techniques. The results reveal that the inhibition efficiency vary with concentration of the leaf extract and the time of immersion. Maximum inhibition efficiency was found to be 95.92% in 2M HCl with 0.5 g/l concentration of the extract in gravimetric method, while 87.04% was obtained in thermometric method. The inhibiting effect was attributed to the presence of alkaloids, flavonoids, saponins, tannins and phenol in the extract. The adsorption processes of the Jatropha curcas leaves extract onto the mild steel is consistent with the assumptions of Langmuir isotherm model and also found to be spontaneous. From the results, a physical adsorption mechanism is proposed for the adsorption of Jatropha curcas leaves extract onto mild steel surface.

Separation of uranium(VI) by liquid-solid extraction with tri-n-octylphosphine oxide diluted with naphthalene

International Nuclear Information System (INIS)

Shigetomi, Y.; Kojima, T.; Kamba, H.; Yamamoto, Y.

1980-01-01

Liquid-liquid distribution with tri-n-octylphosphine oxide (TOPO) and molten naphthalene has been investigated for the extraction of 20 metals from nitric acid and hydrochloric acid solutions. Uranium is quantitatively extracted from 1 M nitric acid or hydrochloric acid by using 100 mg of TOPO and 200 mg of naphthalene and shaking for 5 min at 80 0 C, and separated from transition metals, alkaline earth metals and rare earth metals (except scandium). Addition of naphthalene increases the extraction efficiency. (Auth.)

Hydrolysis of dilute acid-pretreated cellulose under mild hydrothermal conditions.

Science.gov (United States)

Chimentão, R J; Lorente, E; Gispert-Guirado, F; Medina, F; López, F

2014-10-13

The hydrolysis of dilute acid-pretreated cellulose was investigated in a conventional oven and under microwave heating. Two acids--sulfuric and oxalic--were studied. For both hydrothermal conditions (oven and microwave) the resultant total organic carbon (TOC) values obtained by the hydrolysis of the cellulose pretreated with sulfuric acid were higher than those obtained by the hydrolysis of the cellulose pretreated with oxalic acid. However, the dicarboxylic acid exhibited higher hydrolytic efficiency towards glucose. The hydrolysis of cellulose was greatly promoted by microwave heating. The Rietveld method was applied to fit the X-ray patterns of the resultant cellulose after hydrolysis. Oxalic acid preferentially removed the amorphous region of the cellulose and left the crystalline region untouched. On the other hand, sulfuric acid treatment decreased the ordering of the cellulose by partially disrupting its crystalline structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Nucleic acid-binding glycoproteins which solubilize nucleic acids in dilute acid: re-examination of the Ustilago maydis glycoproteins

Energy Technology Data Exchange (ETDEWEB)

Unrau, P.; Champ, D.R.; Young, J.L.; Grant, C.E.

1980-01-01

Holloman reported the isolation from Ustilago maydis of a glycoprotein which prevented the precipitation of nucleic acids in cold 5% trichloroacetic acid. Two glycoprotein fractions from U. maydis with this nucleic acid-solubilizing activity were isolated in our laboratory using improved purification procedures. The activity was not due to nuclease contamination. The glycoproteins are distinguished by: their ability to bind to concanavalin A-Sepharose; their differential binding to double- and single-stranded deoxyribonucleic acid, and to ribonucleic acid; their molecular weights (46,000 and 69,000); and the relative amounts present in growing versus nongrowing cells. Both fractions required sulfhydryl-reducing conditions for optimal yields, specific activity, and stability. Nucleic acid binding was cooperative, the minimum number of glycoproteins required to make a native T7 DNA molecule soluble in dilute acid being estimated at 2 and 15, respectively.

Dilute-acid pretreatment of barley straw for biological hydrogen production using Caldicellulosiruptor saccharolyticus

NARCIS (Netherlands)

Panagiotopoulos, I.A.; Bakker, R.R.C.; Vrije, de G.J.; Claassen, P.A.M.; Koukios, E.G.

2012-01-01

The main objective of this study was to use the fermentability test to investigate the feasibility of applying various dilute acids in the pretreatment of barley straw for biological hydrogen production. At a fixed acid loading of 1% (w/w dry matter) 28-32% of barley straw was converted to soluble

Liquid-liquid extraction/separation of platinum(IV) and rhodium(III) from acidic chloride solutions using tri-iso-octylamine

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin-Young, E-mail: jinlee@kigam.re.kr [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of); Rajesh Kumar, J., E-mail: rajeshkumarphd@rediffmail.com [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of); Kim, Joon-Soo; Park, Hyung-Kyu; Yoon, Ho-Sung [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of)

2009-08-30

Liquid-liquid extraction/separation of platinum(IV) and rhodium(III) from acidic chloride solutions was carried out using tri-iso-octylamine (Alamine 308) as an extractant diluted in kerosene. The percentage extraction of platinum(IV) and rhodium(III) increased with increase in acid concentration up to 8 mol L{sup -1}. However, at 10 mol L{sup -1} HCl concentration, the extraction behavior was reversed, indicating the solvation type mechanism during extraction. The quantitative extraction of {approx}98% platinum(IV) and 36% rhodium(III) was achieved with 0.01 mol L{sup -1} Alamine 308. The highest separation factor (S.F. = 184.7) of platinum(IV) and rhodium(III) was achieved with 0.01 mol L{sup -1} Alamine 308 at 1.0 mol L{sup -1} of hydrochloric acid concentration. Alkaline metal salts like sodium chloride, sodium nitrate, sodium thiocyanate, lithium chloride, lithium nitrate, potassium chloride and potassium thiocyanate used for the salting-out effect. LiCl proved as best salt for the extraction of platinum(IV). Temperature effect demonstrates that the extraction process is exothermic. Hydrochloric acid and thiourea mixture proved to be better stripping reagents when compared with other mineral acids and bases.

Determination of tungsten in high-alloy steels and heat resisting alloys by isotope dilution-spark source mass spectrometry

International Nuclear Information System (INIS)

Saito, Morimasa; Yamada, Kei; Okochi, Haruno; Hirose, Fumio

1983-01-01

Tungsten in high-alloy steels and heat-resisting alloys was determined by isotope dilution method combined with spark source mass spectrometry by using 183 W enriched tungsten. The spike solution was prepared by fusing tungsten trioxide in sodium carbonate. A high-alloy steel sample was dissolved in the mixture of sulfuric acid and phosphoric acid together with the spike solution; a sample of heat resisting alloy was similarly dissolved in the mixture of hydrochloric acid, nitric acid, sulfuric acid, and phosphoric acid. The solution was evaporated to give dense white fumes. Tungsten was separated from the residue by a conventional cinchonine salt-precipitation method. The salt was ignited, and the residue was mixed with graphite powder and pressed into electrodes. The isotope 183 W and 184 W were measured. The method was applied to the determination of tungsten in JSS and NBS standard high-alloy steels and JAERI standard nickel- and NBS standard cobalt-base heat resisting alloys containing more than 0.05% tungsten. The results were obtained with satisfactory precision and accuracy. However, the results obtained for JSS standard high- speed steels containing molybdenum tended to be significantly lower than the certified values. (author)

A kinetic study of plutonium dioxide dissolution in hydrochloric acid using iron (II) as an electron transfer catalyst

International Nuclear Information System (INIS)

Fife, K.W.

1996-09-01

Effective dissolution of plutonium dioxide has traditionally been accomplished by contact with strong nitric acid containing a small amount of fluoride at temperatures of ∼ 100 C. In spite of these aggressive conditions, PuO 2 dissolution is sometimes incomplete requiring additional contact with the solvent. This work focused on an alternative to conventional dissolution in nitric acid where an electron transfer catalyst, Fe(II), was used in hydrochloric acid. Cyclic voltammetry was employed as an in-situ analytical technique for monitoring the dissolution reaction rate. The plutonium oxide selected for this study was decomposed plutonium oxalate with > 95% of the material having a particle diameter (< 70 microm) as determined by a scanning laser microscopy technique. Attempts to dry sieve the oxide into narrow size fractions prior to dissolution in the HCl-Fe(II) solvent system failed, apparently due to significant interparticle attractive forces. Although sieve splits were obtained, subsequent scanning laser microscopy analysis of the sieve fractions indicated that particle segregation was not accomplished and the individual sieve fractions retained a particle size distribution very similar to the original powder assemblage. This phenomena was confirmed through subsequent dissolution experiments on the various screen fractions which illustrated no difference in kinetic behavior between the original oxide assemblage and the sieve fractions

Alteration of the phospho- or neutral lipid content and fatty acid composition in Listeria monocytogenes due to acid adaptation mechanisms for hydrochloric, acetic and lactic acids at pH 5.5 or benzoic acid at neutral pH.

Science.gov (United States)

Mastronicolis, Sofia K; Berberi, Anita; Diakogiannis, Ioannis; Petrova, Evanthia; Kiaki, Irene; Baltzi, Triantafillia; Xenikakis, Polydoros

2010-10-01

This study provides a first approach to observe the effects on Listeria monocytogenes of cellular exposure to acid stress at low or neutral pH, notably how phospho- or neutral lipids are involved in this mechanism, besides the fatty acid profile alteration. A thorough investigation of the composition of polar and neutral lipids from L. monocytogenes grown at pH 5.5 in presence of hydrochloric, acetic and lactic acids, or at neutral pH 7.3 in presence of benzoic acid, is described relative to cells grown in acid-free medium. The results showed that only low pH values enhance the antimicrobial activity of an acid. We suggest that, irrespective of pH, the acid adaptation response will lead to a similar alteration in fatty acid composition [decreasing the ratio of branched chain/saturated straight fatty acids of total lipids], mainly originating from the neutral lipid class of adapted cultures. Acid adaptation in L. monocytogenes was correlated with a decrease in total lipid phosphorus and, with the exception of cells adapted to benzoic acid, this change in the amount of phosphorus reflected a higher content of the neutral lipid class. Upon acetic or benzoic acid stress the lipid phosphorus proportion was analysed in the main phospholipids present: cardiolipin, phosphatidylglycerol, phosphoaminolipid and phosphatidylinositol. Interestingly only benzoic acid had a dramatic effect on the relative quantities of these four phospholipids.

A dilute chemical decontaminant formulation containing gallic acid as a reductant

International Nuclear Information System (INIS)

Kishore, K.; Rajesh, P.; Kumbhar, A.G.

2001-01-01

Gallic acid (GA) was tried as a reductant in place of ascorbic acid in dilute chemical decontaminant (DCD) formulations. Dissolution of magnetite in GA based DCD formulations was studied at 50 C as well as 80 C. It was found to be a good substitute for ascorbic acid in EDTA/ascorbic acid/citric acid, i.e., EAC formulation. The efficiency of EDTA/GA/CA formulation was as good as that of EAC formulation. 2.8 was found to be the optimum pH for this formulation and dissolution decreased at lower as well as higher pHs. The ion exchange behaviour of GA is also appropriate for using it in a regenerating type of formulation. Being an aromatic compound, Gallic acid has inherent stability against radiation degradation. (orig.)

The separation and determination of fatty acids by isotopic dilution and radiogas-liquid chromatography

International Nuclear Information System (INIS)

Beardsley, D.A.

1981-01-01

A number of static phases have been evaluated for the GLC separation of fatty acids. Of those investigated, only AT 1200 was capable of resolving the isomeric forms of the acids. A radiogas-liquid chromatographic method incorporating isotopic dilution analysis has been developed for the determination of n-butyric acid. The proposed method has been applied to the determination of the acid in hydrolysed butter fat and milk chocolate extracts. (author)

Novel texturing method for sputtered zinc oxide films prepared at high deposition rate from ceramic tube targets

Directory of Open Access Journals (Sweden)

Hüpkes J.

2011-10-01

Full Text Available Sputtered and wet-chemically texture etched zinc oxide (ZnO films on glass substrates are regularly applied as transparent front contact in silicon based thin film solar cells. In this study, chemical wet etching in diluted hydrofluoric acid (HF and subsequently in diluted hydrochloric acid (HCl on aluminum doped zinc oxide (ZnO:Al films deposited by magnetron sputtering from ceramic tube targets at high discharge power (~10 kW/m target length is investigated. Films with thickness of around 800 nm were etched in diluted HCl acid and HF acid to achieve rough surface textures. It is found that the etching of the films in both etchants leads to different surface textures. A two steps etching process, which is especially favorable for films prepared at high deposition rate, was systematically studied. By etching first in diluted hydrofluoric acid (HF and subsequently in diluted hydrochloric acid (HCl these films are furnished with a surface texture which is characterized by craters with typical diameter of around 500 − 1000 nm. The resulting surface structure is comparable to etched films sputtered at low deposition rate, which had been demonstrated to be able to achieve high efficiencies in silicon thin film solar cells.

New Acid Combination for a Successful Sandstone Acidizing

Science.gov (United States)

Shafiq, M. U.; Mahmud, H. K. B.; Rezaee, R.

2017-05-01

With the development of new enhanced oil recovery techniques, sandstone acidizing has been introduced and played a pivotal role in the petroleum industry. Different acid combinations have been applied, which react with the formation, dissolve the soluble particles; thus increase the production of hydrocarbons. To solve the problems which occurred using current preflush sandstone acidizing technology (hydrochloric acid); a new acid combination has been developed. Core flooding experiments on sandstone core samples with dimensions 1.5 in. × 3 in. were conducted at a flow rate of 2 cm3/min. A series of hydrochloric-acetic acid mixtures with different ratios were tested under 150°F temperature. The core flooding experiments performed are aimed to dissolve carbonate, sodium, potassium and calcium particles from the core samples. These experiments are followed by few important tests which include, porosity-permeability, pH value, Inductively Coupled Plasma (ICP) analysis and Nuclear Magnetic Resonance (NMR measurements). All the results are compared with the results of conventional hydrochloric acid technology. NMR and porosity analysis concluded that the new acid combination is more effective in creating fresh pore spaces and thus increasing the reservoir permeability. It can be seen from the pore distribution before and after the acidizing. Prior applying acid; the large size of pores appears most frequently in the pore distribution while with the applied acid, it was found that the small pore size is most the predominant of the pore distribution. These results are validated using ICP analysis which shows the effective removal of calcium and other positive ions from the core sample. This study concludes that the combination of acetic-hydrochloric acid can be a potential candidate for the preflush stage of sandstone acidizing at high temperature reservoirs.

Quantification of γ-Aminobutyric Acid in Cerebrospinal Fluid Using Liquid Chromatography-Electrospray Tandem Mass Spectrometry.

Science.gov (United States)

Arning, Erland; Bottiglieri, Teodoro

2016-01-01

We describe a simple stable isotope dilution method for accurate and precise measurement of γ-aminobutyric acid (GABA), a major inhibitory neurotransmitter in human cerebrospinal fluid (CSF) as a clinical diagnostic test. Determination of GABA in CSF (50 μL) was performed utilizing high performance liquid chromatography coupled with electrospray positive ionization tandem mass spectrometry (HPLC-ESI-MS/MS). Analysis of free and total GABA requires two individual sample preparations and mass spectrometry analyses. Free GABA in CSF is determined by a 1:2 dilution with internal standard (GABA-D2) and injected directly onto the HPLC-ESI-MS/MS system. Determination of total GABA in CSF requires additional sample preparation in order to hydrolyze all the bound GABA in the sample to the free form. This requires hydrolyzing the sample by boiling in acidic conditions (hydrochloric acid) for 4 h. The sample is then further diluted 1:10 with a 90 % acetonitrile/0.1 % formic acid solution and injected into the HPLC-ESI-MS/MS system. Each assay is quantified using a five-point standard curve and is linear from 6 nM to 1000 nM and 0.63 μM to 80 μM for free and total GABA, respectively.

Hydrothermal synthesis of highly crystalline RuS2 nanoparticles as cathodic catalysts in the methanol fuel cell and hydrochloric acid electrolysis

International Nuclear Information System (INIS)

Li, Yanjuan; Li, Nan; Yanagisawa, Kazumichi; Li, Xiaotian; Yan, Xiao

2015-01-01

Highlights: • Highly crystalline RuS 2 nanoparticles have been first synthesized by a “one-step” hydrothermal method. • The product presents a pure cubic phase of stoichiometric ratio RuS 2 with average particle size of 14.8 nm. • RuS 2 nanoparticles were used as cathodic catalysts in methanol fuel cell and hydrochloric acid electrolysis. • The catalyst outperforms commercial Pt/C in methanol tolerance and stability towards Cl − . - Abstract: Highly crystalline ruthenium sulfide (RuS 2 ) nanoparticles have been first synthesized by a “one-step” hydrothermal method at 400 °C, using ruthenium chloride and thiourea as reactants. The products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy/energy disperse spectroscopy (SEM/EDS), thermo gravimetric-differential thermal analyze (TG-DTA), transmission electron microscopy equipped with selected area electron diffraction (TEM/SAED). Fourier transform infrared spectra (IR), and X-ray photoelectron spectroscopy (XPS). XRD result illustrates that the highly crystalline product presents a pure cubic phase of stoichiometric ratio RuS 2 and the average particle size is 14.8 nm. SEM and TEM images display the products have irregular shape of 6–25 nm. XPS analyst indicates that the sulfur exists in the form of S 2 2− . Cyclic voltammetry (CV), rotating disk electrode (RDE), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) measurements are conducted to evaluate the electrocatalytic activity and stability of the highly crystalline RuS 2 nanoparticles in oxygen reduction reaction (ORR) for methanol fuel cell and hydrochloric acid electrolysis. The results illustrate that RuS 2 is active towards oxygen reduction reaction. Although the activity of RuS 2 is lower than that of Pt/C, the RuS 2 catalyst outperforms commercial Pt/C in methanol tolerance and stability towards Cl −

Influence of several nonferrous metals in the treatment of residual liquors from hydrochloric acid pickling processes. Influencia de diversos metales no ferreos en el tratamiento de lejias residuales de decapado con acido clorhidrico

Energy Technology Data Exchange (ETDEWEB)

Negro, C.; Cobos, M.A.; Latorre, R.; Dufour, J.; Formoso, A.; Lopez, F.

1994-01-01

In the oxiprecipitation of waste liquors from siderurgical processes of pickling with hydrochloric acid, several kinds of iron oxides and oxihydroxides are obtained: alpha-FeOOH, gamma-FeOOH, Fe[sub 3]O[sub 4], gamma-Fe[sub 2]O[sub 3]. Fe[sub 2]O[sub 3].1,2H[sub 2]O, etc. These products can be used like pigments in the painting industry and like raw materials for the obtaining of ferrites. Varying the operation conditions, the presence of these products can be changed greatly, obtaining different mixtures of them. The presence of non-ferrous metals catalyzes and modifies the mechanism of the reaction, yielding pure products. This simplifies their later industrial applications. The aim of this work is to determine the influence of Cu(II), Zn(II), Mo(VI) and Al(III) on the oxiprecipitation of residual liquors from hydrochloric acid pickling processes, selecting the most favourable operation conditions at which it is possible to obtain products for industrial applications.

Electrochemical measurements for the corrosion inhibition of mild steel in 1 M hydrochloric acid by using an aromatic hydrazide derivative

Directory of Open Access Journals (Sweden)

P. Preethi Kumari

2017-07-01

Full Text Available The influence of an aromatic hydrazide derivative, 2-(3,4,5-trimethoxybenzylidene hydrazinecarbothioamide (TMBHC as corrosion inhibitor on mild steel in 1 M hydrochloric acid was studied by Tafel polarization and electrochemical impedance spectroscopy (EIS technique. The results showed that the inhibition efficiency (% IE of TMBHC increased with increasing inhibitor concentrations and also with increase in temperatures. TMBHC acted as a mixed type of inhibitor and its adsorption on mild steel surface was found to follow Langmuir’s adsorption isotherm. The evaluation of thermodynamic and activation parameters indicated that the adsorption of TMBHC takes place through chemisorption. The formation of protective film was further confirmed by scanning electron microscopy (SEM.

Effect of foods and drinks on primary tooth enamel after erosive challenge with hydrochloric acid

Directory of Open Access Journals (Sweden)

Késsia Suênia Fidelis de MESQUITA-GUIMARÃES

2015-01-01

Full Text Available The aim of this study was to evaluate the effect of industrialised foods and drinks on primary tooth enamel previously eroded with hydrochloric acid (HCl. The crowns of one hundred two specimens were subjected to an erosive challenge with HCl and randomly divided into six groups (n = 17: Chocolate Milk (Toddynho® - Pepsico - negative control; Petit Suisse Yogurt (Danoninho® - Danone; Strawberry Yogurt (Vigor; Apple puree (Nestlé; Fermented Milk (Yakult® - Yakult; and Home Squeezed Style Orange Juice (del Valle - positive control. The 28-day immersion cycles for the test products were performed twice daily and were interspersed with exposure of the test substrate to artificial saliva. Measurements of enamel surface microhardness (SMH were performed initially, after immersion in HCl and at 7, 14, 21 and 28 days of experimentation. A two-way ANOVA, according to a split-plot design, followed by the sum of squares decomposition and Tukey’s test, revealed a significant effect for the interaction between Foods and Drinks and Length of Exposure (p < 0.00001. Orange juice resulted in greater mineral loss of enamel after 28 days. None of the test products was associated with recovery of tooth enamel microhardness.

Two pyrazine derivatives as inhibitors of the cold rolled steel corrosion in hydrochloric acid solution

Energy Technology Data Exchange (ETDEWEB)

Deng Shuduan, E-mail: dengshuduan@163.co [Faculty of Wood Science and Decoration Technology, Southwest Forestry University, Kunming 650224 (China); Li Xianghong; Fu Hui [Department of Fundamental Courses, Southwest Forestry University, Kunming 650224 (China)

2011-02-15

Research highlights: Two pyrazine derivatives of 2-aminopyrazine (AP) and 2-amino-5-bromopyrazine (ABP) are good inhibitors for the corrosion of steel in 1.0 M HCl solution. The inhibition efficiency follows the order: ABP > AP. The substitution Br of ABP is the additional centre of adsorption and increases the electron density of pyrazine ring, which can facilitate its adsorption on the metal surface. For either ABP or AP, the adsorption obeys Langmuir adsorption isotherm. Both ABP and AP act as mixed-type inhibitors. - Abstract: The inhibition effect of two pyrazine derivatives of 2-aminopyrazine (AP) and 2-amino-5-bromopyrazine (ABP) on the corrosion of cold rolled steel (CRS) in 1.0 M hydrochloric acid (HCl) was studied by weight loss, potentiodynamic polarization curves, and electrochemical impedance spectroscopy (EIS) methods. The results show that both AP and ABP are good inhibitors, and inhibition efficiency follows the order: ABP > AP. The adsorption of each inhibitor on CRS surface obeys Langmuir adsorption isotherm. Potentiodynamic polarization curves show that two pyrazine derivatives act as mixed-type inhibitors. EIS spectra exhibit one capacitive loop and confirm the inhibitive ability.

Two pyrazine derivatives as inhibitors of the cold rolled steel corrosion in hydrochloric acid solution

International Nuclear Information System (INIS)

Deng Shuduan; Li Xianghong; Fu Hui

2011-01-01

Research highlights: → Two pyrazine derivatives of 2-aminopyrazine (AP) and 2-amino-5-bromopyrazine (ABP) are good inhibitors for the corrosion of steel in 1.0 M HCl solution. → The inhibition efficiency follows the order: ABP > AP. The substitution Br of ABP is the additional centre of adsorption and increases the electron density of pyrazine ring, which can facilitate its adsorption on the metal surface. → For either ABP or AP, the adsorption obeys Langmuir adsorption isotherm. → Both ABP and AP act as mixed-type inhibitors. - Abstract: The inhibition effect of two pyrazine derivatives of 2-aminopyrazine (AP) and 2-amino-5-bromopyrazine (ABP) on the corrosion of cold rolled steel (CRS) in 1.0 M hydrochloric acid (HCl) was studied by weight loss, potentiodynamic polarization curves, and electrochemical impedance spectroscopy (EIS) methods. The results show that both AP and ABP are good inhibitors, and inhibition efficiency follows the order: ABP > AP. The adsorption of each inhibitor on CRS surface obeys Langmuir adsorption isotherm. Potentiodynamic polarization curves show that two pyrazine derivatives act as mixed-type inhibitors. EIS spectra exhibit one capacitive loop and confirm the inhibitive ability.

Repletion of branched chain amino acids reverses mTORC1 signaling but not improved metabolism during dietary protein dilution

DEFF Research Database (Denmark)

Maida, Adriano; Chan, Jessica S K; Sjøberg, Kim Anker

2017-01-01

OBJECTIVE: Dietary protein dilution (PD) has been associated with metabolic advantages such as improved glucose homeostasis and increased energy expenditure. This phenotype involves liver-induced release of FGF21 in response to amino acid insufficiency; however, it has remained unclear whether...... dietary dilution of specific amino acids (AAs) is also required. Circulating branched chain amino acids (BCAAs) are sensitive to protein intake, elevated in the serum of obese humans and mice and thought to promote insulin resistance. We tested whether replenishment of dietary BCAAs to an AA-diluted (AAD......) diet is sufficient to reverse the glucoregulatory benefits of dietary PD. METHODS: We conducted AA profiling of serum from healthy humans and lean and high fat-fed or New Zealand obese (NZO) mice following dietary PD. We fed wildtype and NZO mice one of three amino acid defined diets: control, total...

Exploring orange peel treatment with deep eutectic solvents and diluted organic acids

NARCIS (Netherlands)

van den Bruinhorst, A.; Kouris, P.; Timmer, J.M.K.; de Croon, M.H.J.M.; Kroon, M.C.

2016-01-01

The disintegration of orange peel waste in deep eutectic solvents and diluted organic acids is presented in this work. The albedo and flavedo layers of the peel were studied separately, showing faster disintegration of the latter. Addition of water to the deep eutectic solvents lowered the amount of

CHEMICAL EVALUATION OF THE NUTRITIVE\\ i\\Lt:J<: OF ...

African Journals Online (AJOL)

BSN

All essential amino acids were present with phenylanine, leucine. ly ine. .... binding with the substrate to be digested, inhibiting digestive enzymes or heing anti- ... the absence of effective glucosidase, neither saliva nor dilute hydrochloric acid ...

Preservation of urine free catecholamines and their free O-methylated metabolites with citric acid as an alternative to hydrochloric acid for LC-MS/MS-based analyses.

Science.gov (United States)

Peitzsch, Mirko; Pelzel, Daniela; Lattke, Peter; Siegert, Gabriele; Eisenhofer, Graeme

2016-01-01

Measurements of urinary fractionated metadrenalines provide a useful screening test to diagnose phaeochromocytoma. Stability of these compounds and their parent catecholamines during and after urine collection is crucial to ensure accuracy of the measurements. Stabilisation with hydrochloric acid (HCl) can promote deconjugation of sulphate-conjugated metadrenalines, indicating a need for alternative preservatives. Urine samples with an intrinsically acidic or alkaline pH (5.5-6.9 or 7.1-8.7, respectively) were used to assess stability of free catecholamines and their free O-methylated metabolites over 7 days of room temperature storage. Stabilisation with HCl was compared with ethylenediaminetetraacetic acid/metabisulphite and monobasic citric acid. Catecholamines and metabolites were measured by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Free catecholamines and their O-methylated metabolites were stable in acidic urine samples over 7 days of room temperature storage, independent of the presence or absence of any stabilisation method. In contrast, free catecholamines, but not the free O-methylated metabolites, showed rapid degradation within 24 h and continuing degradation over 7 days in urine samples with an alkaline pH. Adjustment of alkaline urine samples to a pH of 3-5 with HCl or 4.8-5.4 with citric acid completely blocked degradation of catecholamines. Ethylenediaminetetraacetic acid/metabisulphite, although reducing the extent of degradation of catecholamines in alkaline urine, was largely ineffectual as a stabiliser. Citric acid is equally effective as HCl for stabilisation of urinary free catecholamines and minimises hazards associated with use of strong inorganic acids while avoiding deconjugation of sulphate-conjugated metabolites during simultaneous LC-MS/MS measurements of free catecholamines and their free O-methylated metabolites.

Studies on rapid ion-exchange separation of the transplutonium elements with mineral acid-methanol mixed media

International Nuclear Information System (INIS)

Usuda, Shigekazu

1989-03-01

In order to study properties of short-lived transplutonium nuclides synthesized by heavy-ion bombardment, three methods for rapid separation of tri-valent transplutonium elements by ion-exchange chromatography with mineral acid-methanol mixed media at elevated temperature were investigated. The first separation method was anion-exchange chromatography with nitric acid-methanol mixed media. The second method was anion-exchange choromatography with dilute hydrochloric acid-methanol mixed media. The third method was improved cation-exchange chromatography with single-column operation using the mixed media of hydrochloric acid and methanol. The separation methods developed were found applicable to studies on synthesis of the trans-plutonium nuclides, 250 Fm (T 1/2 :30 min), 244,245,246 Cf (T 1/2 :20 min, 46 min and 35.7 h, respectively) from the 16 O + 238 U and 12 C + 242 Pu reactions, and on the decay property of 245 Cf. Attempts to search for new actinide nuclides, such as 240 U and neutron deficient nuclides of Am, Cm and Bk, were made by a quick purification. The separation system was also applied to the rapid and effective separation of Nd, Am and Cm from spent nuclear fuel samples, for burn-up determination. (J.P.N.) 242 refs

The Corrosion Behavior of Nickel and Inconel 600 in Sodium Hydroxide and Hydrochloric Acid Solution at 280 .deg. C

International Nuclear Information System (INIS)

Lee, Ihh Chong; Suk, Tae Won

1980-01-01

The corrosion behavior of nickel and Inconel 600 has been investigated by the weight change measurement method at pH ranges 3∼13 of the solution. The specimens were exposed to aqueous solutions in a static autoclave at 280 .deg. C for 210 hours. The pH of the solutions was adjusted by hydrochloric acid and sodium hydroxide and the dissolved oxygen concentration was fixed as 10 ppb by using pure nitrogen gas. Weight loss of Inconel 600 was much less than that of nickel over the tested pH ranges. At pH 9.5, nickel and Inconel 600 showed the minimum weight loss phenomenon and the values of weight loss were 1.5mg/dm 2 and 0.9mg/dm 2 , respectively. Microscopic examination showed that nickel surface was attacked uniformly, whereas Inconel 600 surface was not greatly

Bioconversion of dilute-acid pretreated sorghum bagasse to ethanol by Neurospora crassa

Energy Technology Data Exchange (ETDEWEB)

Dogaris, Ioannis; Gkounta, Olga; Mamma, Diomi; Kekos, Dimitris [National Technical Univ. of Athens, Zografou (Greece). Biotechnology Lab.

2012-07-15

Bioethanol production from sweet sorghum bagasse (SB), the lignocellulosic solid residue obtained after extraction of sugars from sorghum stalks, can further improve the energy yield of the crop. The aim of the present work was to evaluate a cost-efficient bioconversion of SB to ethanol at high solids loadings (16 % at pretreatment and 8 % at fermentation), low cellulase activities (1-7 FPU/g SB) and co-fermentation of hexoses and pentoses. The fungus Neurospora crassa DSM 1129 was used, which exhibits both depolymerase and co-fermentative ability, as well as mixed cultures with Saccharomyces cerevisiae 2541. A dilute-acid pretreatment (sulfuric acid 2 g/100 g SB; 210 C; 10 min) was implemented, with high hemicellulose decomposition and low inhibitor formation. The bioconversion efficiency of N. crassa was superior to S. cerevisiae, while their mixed cultures had negative effect on ethanol production. Supplementing the in situ produced N. crassa cellulolytic system (1.0 FPU/g SB) with commercial cellulase and {beta}-glucosidase mixture at low activity (6.0 FPU/g SB) increased ethanol production to 27.6 g/l or 84.7 % of theoretical yield (based on SB cellulose and hemicellulose sugar content). The combined dilute-acid pretreatment and bioconversion led to maximum cellulose and hemicellulose hydrolysis 73.3 % and 89.6 %, respectively. (orig.)

Hydrogen isotope exchange of organic compounds in dilute acid at elevated temperatures

International Nuclear Information System (INIS)

Werstiuk, N.H.

1987-01-01

Introduction of one or more deuterium (or tritium) atoms into organic molecules can be accomplished in many ways depending on the nature of the substrate and the extent and sterochemistry of deuteriation or tritiation required. Some of the common methods include acid- and base-catalyzed exchange of carbonyl compounds, metal hydride reductions, dissolving metal reductions, catalytic reduction of double bonds, chromatographic exchange, homogeneous and heterogeneous metal-catalyzed exchange, base-catalyzed exchange of carbon acids other than carbonyl compounds and acid-catalyzed exchange via electrophilic substitution. Only the latter three methods have been used for perdeuteriation of organic compounds. A very useful compendium of labeling methods with examples has been available to chemists for some time. Although metal-catalyzed exchange has been used extensively, the method suffers from some deficiencies: irreproducibility of catalyst surfaces, catalyst poisoning, side reactions such as coupling and hydrogenolysis of labile groups and low deuterium incorporation. Usually a number of cycles are required with fresh catalyst and fresh deuterium source to achieve substantial isotope incorporation. Acid-catalyzed exchange of aromatics and alkenes, strongly acidic media such as liquid DBr, concentrated DBr, acetic acid/stannic chloride, concentrated D 3 PO 4 , concentrated DC1, D 3 PO 4 /BF 3 SO 2 , 50-80% D 2 SO 4 and DFSO 4 /SbF 5 at moderate temperatures (<100 degrees) have been used to effect exchange. The methods are not particularly suitable for large scale deuteriations because of the cost and the fact that the recovery and upgrading of the diluted deuterium pool is difficult. This paper describes the hydrogen isotope exchange of a variety of organic compounds in dilute aqueous acid (0.1-0.5 M) at elevated temperatures (150-300 degrees)

Xylanase supplementation on enzymatic saccharification of dilute acid pretreated poplars at different severities

Science.gov (United States)

Chao Zhang; Xinshu Zhuang; Zhao Jiang Wang; Fred Matt; Franz St. John; J.Y. Zhu

2013-01-01

Three pairs of solid substrates from dilute acid pretreatment of two poplar wood samples were enzymatically hydrolyzed by cellulase preparations supplemented with xylanase. Supplementation of xylanase improved cellulose saccharification perhaps due to improved cellulose accessibility by xylan hydrolysis. Total xylan removal directly affected enzymatic cellulose...

Transpassive dissolution of alloy 625, chromium, nickel, and molybdenum in high-temperature solutions containing hydrochloric acid and oxygen

International Nuclear Information System (INIS)

Kritzer, P.; Boukis, N.; Dinjus, E.

2000-01-01

Coupons of nickel, molybdenum, chromium, and the nickel-based Alloy 625 (UNS 06625) were corroded in strongly oxidizing hydrochloric acid (HCl) solutions at 350 C and a pressure (p) of 24 MPa, with reaction times between 0.75 h and 50 h. For Alloy 625, the effect of surface roughness also was investigated. Nickel and molybdenum showed strong material loss after only 5 h of reaction as a result of the instability of the solid oxides formed under experimental conditions. The attack on chromium started at the grain boundaries. At longer reaction times, thick, spalling oxide layers formed on the surface. The attack on Alloy 625 also started at the grain boundaries and at inclusions leading to the formation of small pits. On polished surfaces, the growth of these pits occurred faster than on nonpolished surfaces, but fewer pits grew. Corrosion products formed at the surface consisted of oxygen and chromium. On isolated spots, nickel- and chlorine-containing products also were found

Extraction of metal cations by polyterephthalamide microcapsules containing a poly(acrylic acid) gel.

Science.gov (United States)

Laguecir, A; Ernst, B; Frère, Y; Danicher, L; Burgard, M

2002-01-01

Polyterephthalamide microcapsules containing a poly(acrylic acid) gel as a macromolecular ligand (PAA-CAPS) were prepared using an original two step polymerization process in a water-in-oil inverse emulsion system. A polyamide microcapsule containing acrylic acid, initiator and cross-linking agent, is formed by interfacial polycondensation of terephthaloyl dichloride with hexamethylenediamine. In situ radical polymerization of the microcapsule core acrylic acid is initiated to obtain encapsulated poly(acrylic acid) gel. Reference polyamide microcapsules, i.e. without ligand (CAPS), were also synthesized. The mean diameter of synthesized microcapsules was 210 microm, and the microcapsule wall thickness was evaluated by SEM and TEM observations of microcapsule cross-section cuts. The microcapsule water content was determined by thermogravimetric experiments. The extractabilities of Cu(II), Ni(II), Co(II) and Zn(II) into PAA-CAPS were examined. The stripping of the various cations can be promoted in diluted hydrochloric acid solutions.

Ethanol production from industrial hemp: effect of combined dilute acid/steam pretreatment and economic aspects

DEFF Research Database (Denmark)

Gunnarsson, Ingólfur Bragi; Svensson, Sven-Erik; Prade, Thomas

2014-01-01

In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis and etha......In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis...... pretreated at the optimal conditions showed positive economic results. The type of hemp cultivation (organic or conventional) did not influence significantly the effectiveness of the pretreatment and subsequent enzymatic hydrolysis and ethanol fermentation....

STUDY ON THE EFFECTS OF ACID ETCHING ON AFFECTED ENAMEL

Directory of Open Access Journals (Sweden)

Simona Stoleriu

2011-12-01

Full Text Available The purpose of the study was to establish and compare the effects of ortophosphoric and hydrochloric acids on the enamel affected by incipient carious lesions with different evolution. Materials and method. 20 teeth with acute and chronic non-cavitary carious lesions were considered for the study. The teeth were sectioned in two halves through the middle of the non-cavitary lesions. The halves of 5 white spot-type lesions and of 5 brown spot-type ones were analyzed as to their surface roughness, on an atomic force microscope (AFM. 5 halves with white spot-type lesions and 5 halves with brown spot-type ones were subjected to acid etching with 37% ortophosphoric acid (Scotchbond etchant gel, 3M ESPE, and an equal number of samples was subjected to the action of 15% hydrochloric acid (ICON-etch, DMG Dental Products Ltd for 2 min, then washed with water and analyzed by AFM. Results. The initial surface roughness of the enamel was higher in the white spot–type carious lesions, comparatively with the brown spot-type ones. For both types of carious non-cavitary lesions, acid etching with phosphoric and hydrochloric acid significantly increased the surface roughness of the enamel, comparatively with the status of the enamel surface prior to etching. The hydrochloric acid led to a surface roughness significantly higher than in the case of ortophosphoric acid, in both acute and chronic non-cavitary carious lesions. The roughness values obtained through etching with ortophosphoric and hydrochloric acid were higher in the white spot-type carious lesions, comparatively with the brown spot-type ones. Conclusions. Both the 37% ortophosphoric acid and the 15% hydrochloric acid determined a significantly higher surface roughness of the enamel affected by acute and chronic non-cavitary carious lesions. The surface condition of the brown spot-type carious lesions was less significantly modified, comparatively with that of the white spot-type lesions, by the

Materials for making coke

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1936-08-19

In the preparation of carbonized fuel briquettes, material such as bituminous, lignitic, or anthracitic coal, slack, waste or shale is treated with an electropositive solution such as hydrochloric acid or an acidic chloride to bring ash-forming constituents into colloidal form. The mixture is pressed with a colloid precipitating electro-negative solution such as sodium hydroxide, and moulded, the product being heated in the absence of air and coked. In an example bituminous coal is ground and then masticated with dilute hydrochloric acid. Some dilute manganese chloride is added followed by a solution of sodium hydroxide which precipitates the metals and silica as colloidal gels while the mixture is thoroughly agitated. The plastic mass is briquetted and dried at about 125/sup 0/C and then coked in vertical ovens at 700/sup 0/C. Chlorides recovered with the distillate gases may be utilized as solvent instead of hydrochloric acid. If the coal contains a large amount of sulfur acidified manganese chloride including a large proportion of iron is used as colloid forming material, the oxides of manganese and iron subsequently precipitated forming stable compounds with the non-volatile sulfur on coking or combustion.

High-Yield Production of Levulinic Acid from Pretreated Cow Dung in Dilute Acid Aqueous Solution

Directory of Open Access Journals (Sweden)

Jialei Su

2017-02-01

Full Text Available Agricultural waste cow dung was used as feedstock for the production of a high value–added chemical levulinic acid (LA in dilute acid aqueous solutions. A high LA yield of 338.9 g/kg was obtained from the pretreated cow dung, which was much higher than that obtained from the crude cow dung (135 g/kg, mainly attributed to the breakage of the lignin fraction in the lignocellulose structure of the cow dung by potassium hydroxide (KOH pretreatment, and thus enhanced the accessibility of cow dung to the acid sites in the catalytic reaction. Meanwhile, another value-added chemical formic acid could be obtained with a yield of ca. 160 g/kg in the process, implying a total production of ca. 500 g/kg yield for LA and formic acid from the pretreated cow dung with the proposed process. The developed process was shown to be tolerant to high initial substrate loading with a satisfied LA yield. This work provides a promising strategy for the value-increment utilization of liglocellulosic agricultural residues.

Effects of SPORL and dilute acid pretreatment on substrate morphology, cell physical and chemical wall structures, and subsequent enzymatic hydrolysis of lodgepole pine.

Science.gov (United States)

Li, Xinping; Luo, Xiaolin; Li, Kecheng; Zhu, J Y; Fougere, J Dennis; Clarke, Kimberley

2012-11-01

The effects of pretreatment by dilute acid and sulfite pretreatment to overcome recalcitrance of lignocellulose (SPORL) on substrate morphology, cell wall physical and chemical structures, along with the subsequent enzymatic hydrolysis of lodgepole pine substrate were investigated. FE-SEM and TEM images of substrate structural morphological changes showed that SPORL pretreatment resulted in fiber separation, where SPORL high pH (4.2) pretreatment exhibited better fiber separation than SPORL low pH (1.9) pretreatment. Dilute acid pretreatment produced very poor fiber separation, consisting mostly of fiber bundles. The removal of almost all hemicelluloses in the dilute acid pretreated substrate did not overcome recalcitrance to achieve a high cellulose conversion when lignin removal was limited. SPORL high pH pretreatment removed more lignin but less hemicellulose, while SPORL low pH pretreatment removed about the same amount of lignin and hemicelluloses in lodgepole pine substrates when compared with dilute acid pretreatment. Substrates pretreated with either SPORL process had a much higher cellulose conversion than those produced with dilute acid pretreatment. Lignin removal in addition to removal of hemicellulose in SPORL pretreatment plays an important role in improving the cellulose hydrolysis of the substrate.

Optimisation of dilute acid pre-treatment of artisan rice hulls for ethanol production

International Nuclear Information System (INIS)

Lopez, Yoney; Martin, Carlos; Gullon, Beatriz; Parajo, Juan Carlos

2011-01-01

Rice hulls are potential low-cost feedstocks for fuel ethanol production in many countries. In this work, the dilute-acid pre-treatment of artisan rice hulls was investigated using a central composite rotatable experimental design. The experimental variables were temperature (140-210 C), biomass load (5-20%) and sulphuric acid concentration (0.5-1.5 g per 100 g of reaction mixture). A total of 16 experimental runs, including a 23-plan, two replicates at the central point and six star points, were carried out. Low temperatures were found to be favourable for the hydrolysis of xylan and of the easily hydrolyzable glucan fraction. High glucose formation (up to 15.3 g/100 g), attributable to starch hydrolysis, was detected in the hydrolysates obtained under the least severe pre-treatment conditions. Using the experimental results, several models for predicting the effect of the operational conditions on the yield of pretreated solids, xylan and glucan conversion upon pre-treatment, and on enzymatic convertibility of cellulose were developed. Optimum results were predicted for the conversion of easily-hydrolyzable glucan in the material pretreated at 140.7 C, and for the enzymatic saccharification of cellulose in the material pretreated at 169 C. These results suggested the use of two-step acid hydrolysis as future pre-treatment strategy for artisan rice hulls. Key words: Dilute acid hydrolysis, enzymatic hydrolysis, pre-treatment, rice hulls. (author)

Process for recovery and purification of lithium from dilute sources

International Nuclear Information System (INIS)

Kunugita, Eiichi; Kim, Jong-Hwa; Komasawa, Isao

1990-01-01

A process was studied for recovery and purification of lithium from hot spring water and leachate of coal fly ash in which lithium is present at very low concentration in a mixture of high concentration of less desirable species such as alkali metals, alkaline earth metals and others. Lithium is, as a first step, adsorbed selectively by an ion-sieve type adsorbent, λ-MnO 2 , which can effect separation by adsorbing lithium alone in its intraparticle spaces while adsorbing most metals on its surface. Stagewise elutions are performed, employing two elutrients: NH 4 NO 3 and then HNO 3 solution. The concentration ratio of lithium and sodium is 1/70∼1/120 in the original feed stream, and this is upgraded to 300/1 in the pregnant elutrient. Some impurities in the pregnant elutrient is removed by a solvent extraction technique, employing a mixed extractant of a β-diketone (LIX51) and tri-n-octyl-phosphine oxide in kerosene. A lithium solution with an undetectable amount of impurities is obtained by single extraction followed by single scrubbing with dilute hydrochloric acid of carefully controlled concentration. (author)

Removing hydrochloric acid exhaust products from high performance solid rocket propellant using aluminum-lithium alloy

Energy Technology Data Exchange (ETDEWEB)

Terry, Brandon C., E-mail: terry13@purdue.edu [School of Aeronautics and Astronautics, Purdue University, Zucrow Laboratories, 500 Allison Rd, West Lafayette, IN 47907 (United States); Sippel, Travis R. [Department of Mechanical Engineering, Iowa State University, 2025 Black Engineering, Ames, IA 50011 (United States); Pfeil, Mark A. [School of Aeronautics and Astronautics, Purdue University, Zucrow Laboratories, 500 Allison Rd, West Lafayette, IN 47907 (United States); Gunduz, I.Emre; Son, Steven F. [School of Mechanical Engineering, Purdue University, Zucrow Laboratories, 500 Allison Rd, West Lafayette, IN 47907 (United States)

2016-11-05

Highlights: • Al-Li alloy propellant has increased ideal specific impulse over neat aluminum. • Al-Li alloy propellant has a near complete reduction in HCl acid formation. • Reduction in HCl was verified with wet bomb experiments and DSC/TGA-MS/FTIR. - Abstract: Hydrochloric acid (HCl) pollution from perchlorate based propellants is well known for both launch site contamination, as well as the possible ozone layer depletion effects. Past efforts in developing environmentally cleaner solid propellants by scavenging the chlorine ion have focused on replacing a portion of the chorine-containing oxidant (i.e., ammonium perchlorate) with an alkali metal nitrate. The alkali metal (e.g., Li or Na) in the nitrate reacts with the chlorine ion to form an alkali metal chloride (i.e., a salt instead of HCl). While this technique can potentially reduce HCl formation, it also results in reduced ideal specific impulse (I{sub SP}). Here, we show using thermochemical calculations that using aluminum-lithium (Al-Li) alloy can reduce HCl formation by more than 95% (with lithium contents ≥15 mass%) and increase the ideal I{sub SP} by ∼7 s compared to neat aluminum (using 80/20 mass% Al-Li alloy). Two solid propellants were formulated using 80/20 Al-Li alloy or neat aluminum as fuel additives. The halide scavenging effect of Al-Li propellants was verified using wet bomb combustion experiments (75.5 ± 4.8% reduction in pH, ∝ [HCl], when compared to neat aluminum). Additionally, no measurable HCl evolution was detected using differential scanning calorimetry coupled with thermogravimetric analysis, mass spectrometry, and Fourier transform infrared absorption.

Removing hydrochloric acid exhaust products from high performance solid rocket propellant using aluminum-lithium alloy

International Nuclear Information System (INIS)

Terry, Brandon C.; Sippel, Travis R.; Pfeil, Mark A.; Gunduz, I.Emre; Son, Steven F.

2016-01-01

Highlights: • Al-Li alloy propellant has increased ideal specific impulse over neat aluminum. • Al-Li alloy propellant has a near complete reduction in HCl acid formation. • Reduction in HCl was verified with wet bomb experiments and DSC/TGA-MS/FTIR. - Abstract: Hydrochloric acid (HCl) pollution from perchlorate based propellants is well known for both launch site contamination, as well as the possible ozone layer depletion effects. Past efforts in developing environmentally cleaner solid propellants by scavenging the chlorine ion have focused on replacing a portion of the chorine-containing oxidant (i.e., ammonium perchlorate) with an alkali metal nitrate. The alkali metal (e.g., Li or Na) in the nitrate reacts with the chlorine ion to form an alkali metal chloride (i.e., a salt instead of HCl). While this technique can potentially reduce HCl formation, it also results in reduced ideal specific impulse (I_S_P). Here, we show using thermochemical calculations that using aluminum-lithium (Al-Li) alloy can reduce HCl formation by more than 95% (with lithium contents ≥15 mass%) and increase the ideal I_S_P by ∼7 s compared to neat aluminum (using 80/20 mass% Al-Li alloy). Two solid propellants were formulated using 80/20 Al-Li alloy or neat aluminum as fuel additives. The halide scavenging effect of Al-Li propellants was verified using wet bomb combustion experiments (75.5 ± 4.8% reduction in pH, ∝ [HCl], when compared to neat aluminum). Additionally, no measurable HCl evolution was detected using differential scanning calorimetry coupled with thermogravimetric analysis, mass spectrometry, and Fourier transform infrared absorption.

Bioconversion of dilute-acid pretreated sorghum bagasse to ethanol by Neurospora crassa.

Science.gov (United States)

Dogaris, Ioannis; Gkounta, Olga; Mamma, Diomi; Kekos, Dimitris

2012-07-01

Bioethanol production from sweet sorghum bagasse (SB), the lignocellulosic solid residue obtained after extraction of sugars from sorghum stalks, can further improve the energy yield of the crop. The aim of the present work was to evaluate a cost-efficient bioconversion of SB to ethanol at high solids loadings (16 % at pretreatment and 8 % at fermentation), low cellulase activities (1-7 FPU/g SB) and co-fermentation of hexoses and pentoses. The fungus Neurospora crassa DSM 1129 was used, which exhibits both depolymerase and co-fermentative ability, as well as mixed cultures with Saccharomyces cerevisiae 2541. A dilute-acid pretreatment (sulfuric acid 2 g/100 g SB; 210 °C; 10 min) was implemented, with high hemicellulose decomposition and low inhibitor formation. The bioconversion efficiency of N. crassa was superior to S. cerevisiae, while their mixed cultures had negative effect on ethanol production. Supplementing the in situ produced N. crassa cellulolytic system (1.0 FPU/g SB) with commercial cellulase and β-glucosidase mixture at low activity (6.0 FPU/g SB) increased ethanol production to 27.6 g/l or 84.7 % of theoretical yield (based on SB cellulose and hemicellulose sugar content). The combined dilute-acid pretreatment and bioconversion led to maximum cellulose and hemicellulose hydrolysis 73.3 % and 89.6 %, respectively.

The pitting resistance of AISI 316 stainless steel passivated in diluted nitric acid

International Nuclear Information System (INIS)

Barbosa, M.A.

1983-01-01

The pitting resistance of AISI 316 stainless steel after passivation in diluted nitric acid was studied in comparison with that of non-passivated specimens. The passivation treatment increased the pitting potential but decreased the resistance to crevice corrosion under open circuit conditions in aerated sea water. Immersion in the nitric acid solution was found to remove the sulphide inclusions from the metal surface, thus eliminating the most susceptible sites for attack. In the absence of sulphide particles pitting nucleated at aluminium-rich oxides. (author)

Copper-promoted cementation of antimony in hydrochloric acid system: A green protocol

Energy Technology Data Exchange (ETDEWEB)

Wu, Lian-Kui; Li, Ying-Ying; Cao, Hua-Zhen; Zheng, Guo-Qu, E-mail: zhenggq@zjut.edu.cn

2015-12-15

Highlights: • Antimony can be efficiently removed by cementation with copper powder. • Cemented antimony is in the form of Cu{sub 2}Sb. • Consumed copper powder is transformed to CuCl. • The cementation is a chemically controlled step. • No toxic stibine generates during the cementation process. - Abstract: A new method of recovering antimony in hydrochloric acid system by cementation with copper powder was proposed and carried out at laboratory scale. Thermodynamic analysis and cyclic voltammetry test were conducted to study the cementation process. This is a novel antimony removal technology and quite meets the requirements of green chemistry. The main cement product Cu{sub 2}Sb is a promising anodic material for lithium and sodium ion battery. And nearly all consumed copper powder are transformed into CuCl which is an important industrial material. The effect of reaction temperature, stoichiometric ratio of Cu to Sb(III), stirring rate and concentration of HCl on the cementation efficiency of antimony were investigated in detail. Optimized cementation condition is obtained at 60 °C for 120 min and stirring rate of 600 rpm with Cu/Sb(III) stoichiometric ratio of 6 in 3 mol L{sup −1} HCl. At this time, nearly all antimony can be removed by copper powder and the cementation efficiency is over 99%. The structure and morphologies of the cement products were characterized by X-ray diffraction and scanning electron microscopy, respectively. Results show that the reaction temperature has little influence on the morphology of the cement products which consist of particles with various sizes. The activation energy of the cementation antimony on copper is 37.75 kJ mol{sup −1}, indicating a chemically controlled step. Inductively coupled plasma mass spectrometry results show that no stibine generates during the cementation process.

Separation and preconcentration of actinides from acidic media by extraction chromatography

International Nuclear Information System (INIS)

Horwitz, E. Philip; Chiarizia, Renato; Dietz, Mark L.; Diamond, Herbert; Nelson, Donald M.

1993-01-01

A systematic examination of the effect of nitric and hydrochloric acid concentrations and of macro levels of selected elements on the sorption of actinide ions by a novel extraction chromatographic resin comprised of a solution of octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide in tri-n-butyl phosphate supported on an inert polymeric substrate is described. Actinide sorption is demonstrated to be most efficient at high (>1 M) nitric acid concentrations, although tetra- and hexavalent actinides are strongly retained even from dilute (e.g., 0.05 M) nitric acid solutions. Macro concentrations of several common anions (e.g., PO 4 3- and SO 4 2- ) or complexing agents (e.g., oxalic acid) are shown not to adversely affect the sorption of trivalent actinides, while reducing the sorption of tetravalents. Such effects, together with oxidation state adjustments, are shown to provide a basis for the sequential elution of individual actinides and for actinide isolation from environmental and biological matrices

Effect of dilution and L-malic acid addition on bio-hydrogen production with Rhodopseudomonas palustris from effluent of an acidogenic anaerobic reactor

International Nuclear Information System (INIS)

Azbar, N.; Tuba, F.; Dokgoz, C.

2009-01-01

In this study, H 2 was produced in a two-stage biological process: I) first stage; the dark fermentation of cheese whey wastewater, which is rich in lactose, by mixed anaerobic culture grown at thermophilic temperature in a continuously running fermentor and ii) second stage; the photo-fermentation of the residual medium by R. palustris strain (DSM 127) at 31 o C under illumination of 150 W in batch mode, respectively. In the first part of the study, the effluent from the dark fermentation reactor was used either as it is (no dilution) or after dilution with distilled water at varying ratios such as 1/2 , 1/5, 1/10 (1 volume effluent/5 volume distilled water) before used in photo-fermentation experiments. In the second part of the study, L-malic acid at varying amounts was added into the hydrogen production medium in order to have L-malic acid concentrations ranging from 0 to 4 g/l. Non-diluted and pre-diluted mediums with or without L-malic acid addition were also tested for comparison purpose (as controls). Prior to the hydrogen production experiments, all samples were subjected to pH adjustment, (pH 6.7) and sterilized by autoclave at 121 o C for 15 min. In regards to the experiments in which the effect of dilution of the effluent from dark fermentation was studied, it was observed that dilution of the effluent from dark fermentation resulted in much better hydrogen productions. Among the dilution rates used, the experiments operated with 1/5 dilution ratio produced the best hydrogen production (241 ml H 2 / g COD fed ). On the other hand, it was seen that the mixing the effluent with L-malic acid (0 - 4 g/l) at increasing ratios (studied from 0% L-malic acid up to 100% by volume in the mixture) had further positive effect and improved the hydrogen production. The bioreactors containing only L-malic acid media resulted in the best hydrogen production (438 ml H 2 / g COD fed ). It was found that, undiluted raw cheese whey wastewater effluent from dark hydrogen

Removing hydrochloric acid exhaust products from high performance solid rocket propellant using aluminum-lithium alloy.

Science.gov (United States)

Terry, Brandon C; Sippel, Travis R; Pfeil, Mark A; Gunduz, I Emre; Son, Steven F

2016-11-05

Hydrochloric acid (HCl) pollution from perchlorate based propellants is well known for both launch site contamination, as well as the possible ozone layer depletion effects. Past efforts in developing environmentally cleaner solid propellants by scavenging the chlorine ion have focused on replacing a portion of the chorine-containing oxidant (i.e., ammonium perchlorate) with an alkali metal nitrate. The alkali metal (e.g., Li or Na) in the nitrate reacts with the chlorine ion to form an alkali metal chloride (i.e., a salt instead of HCl). While this technique can potentially reduce HCl formation, it also results in reduced ideal specific impulse (ISP). Here, we show using thermochemical calculations that using aluminum-lithium (Al-Li) alloy can reduce HCl formation by more than 95% (with lithium contents ≥15 mass%) and increase the ideal ISP by ∼7s compared to neat aluminum (using 80/20 mass% Al-Li alloy). Two solid propellants were formulated using 80/20 Al-Li alloy or neat aluminum as fuel additives. The halide scavenging effect of Al-Li propellants was verified using wet bomb combustion experiments (75.5±4.8% reduction in pH, ∝ [HCl], when compared to neat aluminum). Additionally, no measurable HCl evolution was detected using differential scanning calorimetry coupled with thermogravimetric analysis, mass spectrometry, and Fourier transform infrared absorption. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydrothermal synthesis of highly crystalline RuS{sub 2} nanoparticles as cathodic catalysts in the methanol fuel cell and hydrochloric acid electrolysis

Energy Technology Data Exchange (ETDEWEB)

Li, Yanjuan [Key Laboratory of Marine Chemistry Theory and Technology, Minisry of Education Ocean University of China, Qingdao, 266100 (China); College of Material Science and Engineering, Key Laboratory of Automobile Materials of Ministry of Education, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Li, Nan, E-mail: lin@jlu.edu.cn [College of Material Science and Engineering, Key Laboratory of Automobile Materials of Ministry of Education, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Yanagisawa, Kazumichi [Research Laboratory of Hydrothermal Chemistry, Kochi University, Kochi 780-8520 (Japan); Li, Xiaotian [College of Material Science and Engineering, Key Laboratory of Automobile Materials of Ministry of Education, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Yan, Xiao [Key Laboratory of Physics and Technology for Advanced Batteries (Ministry of Education), College of Physics, Jilin University, Changchun 130012 (China)

2015-05-15

Highlights: • Highly crystalline RuS{sub 2} nanoparticles have been first synthesized by a “one-step” hydrothermal method. • The product presents a pure cubic phase of stoichiometric ratio RuS{sub 2} with average particle size of 14.8 nm. • RuS{sub 2} nanoparticles were used as cathodic catalysts in methanol fuel cell and hydrochloric acid electrolysis. • The catalyst outperforms commercial Pt/C in methanol tolerance and stability towards Cl{sup −}. - Abstract: Highly crystalline ruthenium sulfide (RuS{sub 2}) nanoparticles have been first synthesized by a “one-step” hydrothermal method at 400 °C, using ruthenium chloride and thiourea as reactants. The products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy/energy disperse spectroscopy (SEM/EDS), thermo gravimetric-differential thermal analyze (TG-DTA), transmission electron microscopy equipped with selected area electron diffraction (TEM/SAED). Fourier transform infrared spectra (IR), and X-ray photoelectron spectroscopy (XPS). XRD result illustrates that the highly crystalline product presents a pure cubic phase of stoichiometric ratio RuS{sub 2} and the average particle size is 14.8 nm. SEM and TEM images display the products have irregular shape of 6–25 nm. XPS analyst indicates that the sulfur exists in the form of S{sub 2}{sup 2−}. Cyclic voltammetry (CV), rotating disk electrode (RDE), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) measurements are conducted to evaluate the electrocatalytic activity and stability of the highly crystalline RuS{sub 2} nanoparticles in oxygen reduction reaction (ORR) for methanol fuel cell and hydrochloric acid electrolysis. The results illustrate that RuS{sub 2} is active towards oxygen reduction reaction. Although the activity of RuS{sub 2} is lower than that of Pt/C, the RuS{sub 2} catalyst outperforms commercial Pt/C in methanol tolerance and stability towards Cl{sup −}.

High temperature dilute phosphoric acid pretreatment of corn stover for furfural and ethanol production

Science.gov (United States)

Furfural was produced from corn stover by one stage pretreatment process using dilute H3PO4 and solid residues following furfural production were used for ethanol production by Saccharomyces cerevisiae NRRL- Y2034. A series of experiments were conducted at varied temperatures (140-200 oC) and acid ...

Efflux of inorganic substances from young barley roots. I. Efflux in water culture under various conditions

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H; Kojima, S [Radiation Center of Osaka Prefecture, Sakai (Japan)

1977-09-01

The efflux of elements from the roots of hydropomically grown young barley plants was studied. The effects of different mutrient compositions and pH values of the solutions was also studied using /sup 22/Na and /sup 45/Ca as the indexes. In all culture conditions, there was efflux of both elements. In two media with dilute hydrochloric acid and AlCl/sub 3/, respectively, the tendencies of Na and Ca efflux were similar in both media at first, but after 72 hr, the Na efflux in AlCl/sub 3/ decreased and that in dilute hydrochloric acid medium increased. The Ca efflux was high in AlCl/sub 3/ medium,however. The efflux of both Na and Ca was higher in the standard medium than in the media with some bases of high concentrations.

Influence of the use of acids and films in post-harvest lychee conservation

Directory of Open Access Journals (Sweden)

Danielle Fabíola Pereira da Silva

2012-12-01

Full Text Available Lychee (Litchi chinensis Sonn. has a high commercial value; however, it has a short shelf-life because of its rapid pericarp browning. The objective of this study was to evaluate the shelf-life of 'Bengal' lychee fruits stored after treatment with hydrochloric acid and citric acid, associated with cassava starch and plastic packaging. Uniformly red pericarp fruits were submitted to treatments: 1-(immersion in citric acid 100 mM for 5 minutes + cassava starch 30 g L-1 for 5 minutes, 2-(immersion in hydrochloric acid 1 M for 2 minutes + starch cassava 30 g L-1 for 5 minutes, 3-(immersion in citric acid 100 mM for 5 minutes + polyvinyl chloride film (PVC, 14 µm thick and 4-(immersion in hydrochloric acid 1 M for 2 minutes + PVC film. During 20 days, the fruits were evaluated for mass loss, pericarp color, pH, soluble solids and titratable acidity, vitamin C of the pulp and pericarp and activities of polyphenol oxidase and peroxidase of the pericarp. The treatment with hydrochloric acid associated with PVC was the most effective in maintaining the red color of the pericarp for a period of 20 days and best preservation of the fruit. The cassava starch associated with citric acid, and hydrochloric acid did not reduce the mass loss and did not prevent the browning of lychee fruit pericarp.

Effect of dilution and L-malic acid addition on bio-hydrogen production with Rhodopseudomonas palustris from effluent of an acidogenic anaerobic reactor

Energy Technology Data Exchange (ETDEWEB)

Azbar, N.; Tuba, F.; Dokgoz, C. [Bioengineering Dept., Faculty of Engineering, Ege Univ., Izmir (Turkey)], E-mail: nuri.azbar@ege.edu.tr

2009-07-01

In this study, H{sub 2} was produced in a two-stage biological process: I) first stage; the dark fermentation of cheese whey wastewater, which is rich in lactose, by mixed anaerobic culture grown at thermophilic temperature in a continuously running fermentor and ii) second stage; the photo-fermentation of the residual medium by R. palustris strain (DSM 127) at 31{sup o}C under illumination of 150 W in batch mode, respectively. In the first part of the study, the effluent from the dark fermentation reactor was used either as it is (no dilution) or after dilution with distilled water at varying ratios such as 1/2 , 1/5, 1/10 (1 volume effluent/5 volume distilled water) before used in photo-fermentation experiments. In the second part of the study, L-malic acid at varying amounts was added into the hydrogen production medium in order to have L-malic acid concentrations ranging from 0 to 4 g/l. Non-diluted and pre-diluted mediums with or without L-malic acid addition were also tested for comparison purpose (as controls). Prior to the hydrogen production experiments, all samples were subjected to pH adjustment, (pH 6.7) and sterilized by autoclave at 121{sup o}C for 15 min. In regards to the experiments in which the effect of dilution of the effluent from dark fermentation was studied, it was observed that dilution of the effluent from dark fermentation resulted in much better hydrogen productions. Among the dilution rates used, the experiments operated with 1/5 dilution ratio produced the best hydrogen production (241 ml H{sub 2}/ g COD{sub fed}). On the other hand, it was seen that the mixing the effluent with L-malic acid (0 - 4 g/l) at increasing ratios (studied from 0% L-malic acid up to 100% by volume in the mixture) had further positive effect and improved the hydrogen production. The bioreactors containing only L-malic acid media resulted in the best hydrogen production (438 ml H{sub 2} / g COD{sub fed}). It was found that, undiluted raw cheese whey wastewater

Production of spent mushroom substrate hydrolysates useful for cultivation of Lactococcus lactis by dilute sulfuric acid, cellulase and xylanase treatment.

Science.gov (United States)

Qiao, Jian-Jun; Zhang, Yan-Fei; Sun, Li-Fan; Liu, Wei-Wei; Zhu, Hong-Ji; Zhang, Zhijun

2011-09-01

Spent mushroom substrate (SMS) was treated with dilute sulfuric acid followed by cellulase and xylanase treatment to produce hydrolysates that could be used as the basis for media for the production of value added products. A L9 (3(4)) orthogonal experiment was performed to optimize the acid treatment process. Pretreatment with 6% (w/w) dilute sulfuric acid at 120°C for 120 min provided the highest reducing sugar yield of 267.57 g/kg SMS. No furfural was detected in the hydrolysates. Exposure to 20PFU of cellulase and 200 XU of xylanase per gram of pretreated SMS at 40°C resulted in the release of 79.85 g/kg or reducing sugars per kg acid pretreated SMS. The dilute sulfuric acid could be recycled to process fresh SMS four times. SMS hydrolysates neutralized with ammonium hydroxide, sodium hydroxide, or calcium hydroxide could be used as the carbon source for cultivation of Lactococcus lactis subsp. lactis W28 and a cell density of 2.9×10(11)CFU/mL could be obtained. The results provide a foundation for the development of value-added products based on SMS. Copyright © 2011 Elsevier Ltd. All rights reserved.

Revealing the Molecular Structural Transformation of Hardwood and Softwood in Dilute Acid Flowthrough Pretreatment

Energy Technology Data Exchange (ETDEWEB)

Zhang, Libing; Pu, Yunqiao; Cort, John R.; Ragauskas, Arthur J.; Yang, Bin

2016-12-05

To better understand the intrinsic recalcitrance of lignocellulosic biomass, the main hurdle to its efficient deconstruction, the effects of dilute acid flowthrough pretreatment on the dissolution chemistry of hemicellulose, cellulose, and lignin for both hardwood (e.g. poplar wood) and softwood (e.g. lodgepole pine wood) were investigated at temperatures of 200 °C to 270 °C and a flow rate of 25 mL/minute with 0.05% (w/w) H2SO4. Results suggested that the softwood cellulose was more readily to be degraded into monomeric sugars than that of hardwood under same pretreatment conditions. However, while the hardwood lignin was completely removed into hydrolysate, ~30% of the softwood lignin remained as solid residues under identical conditions, which was plausibly caused by vigorous C5-active recondensation reactions (C-C5). Unique molecular structural features that pronounced the specific recalcitrance of hardwood and softwood to dilute acid pretreatment were identified for the first time in this study, providing important insights to establish the effective biomass pretreatment.

Synthesis of a-amino amides via a-amino imidoylbenzotriazoles

Directory of Open Access Journals (Sweden)

ALAN R. KATRITZKY

2005-03-01

Full Text Available Reactions of isonitriles 11a-c with N-(a-aminoalkylbenzotriazoles 10a-k afford N-(a-aminoimidoylbenzotriazoles 12a-q which on hydrolysis by dilute hydrochloric acid gave a-amino amides 14a-j.

Comparison of Dilute Acid and Ionic Liquid Pretreatment of Switchgrass: Biomass Recalcitrance, Delignification and Enzymatic Saccharification

Science.gov (United States)

The efficiency of two biomass pretreatment technologies, dilute acid hydrolysis and dissolution in an ionic liquid, are compared in terms of delignification, saccharification efficiency and saccharide yields with switchgrass serving as a model bioenergy crop. When subject to ionic liquid pretreatme...

Variation of structures of ingredients of desiccated coconut during hydrolysis by hydrochloric acid at low temperature

Directory of Open Access Journals (Sweden)

Jian XIONG

2017-10-01

Full Text Available Abstract Owing to the high content of lignocellulose, desiccated coconut become a healthy material for dietary fiber supplementation. In this study, the changes in solubility of the fibers of desiccated coconut were evaluated. The changes of the pHs and weight losses were studied. Furthermore, variations of the ingredient structures of desiccated coconut by hydrolysis by hydrochloric acid were characterized by Fourier transform infrared spectroscopy (FTIR, X-ray diffraction (XRD and scanning electron microscopy (SEM. After hydrolysis 30 s, the pHs of all systems increased, while six hours later, the pH of only system with initial pH = 1.00 decreased. The decline of pH only existed in hydrolysis systems with initial pH = 1.00, there is no relevant with the quantities of desiccated coconut. The lower initial pH of hydrolysis system was, the less the intrinsic viscosity of the desiccated coconut after hydrolysis was, the small the crystallinity was. After hydrolysis, the microstructure of the desiccated coconut become looser, and the secondary structure of the coconut protein became more stable and ordered. The results suggest that the hydrolysis of desiccated coconut mainly occurred in the branched chain and the non-crystalline region of lignocellulose, which transforms some insoluble dietary fiber into soluble dietary fiber. This improves the nutritional value of desiccated coconut.

Inhibiting Effect of Nicotinic Acid Hydrazide on Corrosion of Aluminum and Mild Steel in Acidic Medium

Energy Technology Data Exchange (ETDEWEB)

Bhat, J. Ishwara [Mangalore Univ., Karnataka (India); Alva, Vijaya D. P. [Shree Devi Institute of Technology, Karnataka (India)

2014-02-15

The corrosion behavior of aluminum and mild steel in hydrochloric acid medium was studied using a nicotinic acid hydrazide as inhibitor by potentiodynamic polarization, electrochemical impedance spectroscopy technique and gravimetric methods. The effects of inhibitor concentration and temperature were investigated. The experimental results suggested, nicotinic acid hydrazide is a good corrosion inhibitor for both aluminum and mild steel in hydrochloric acid medium and the inhibition efficiency increased with increase in the inhibitor concentration. The polarization studies revealed that nicotinic acid hydrazide exhibits mixed type of inhibition. The inhibition was assumed to occur via adsorption of the inhibitor molecules on the aluminum and mild steel surface and inhibits corrosion by blocking the reaction sites on the surface of aluminum.

Inhibiting Effect of Nicotinic Acid Hydrazide on Corrosion of Aluminum and Mild Steel in Acidic Medium

International Nuclear Information System (INIS)

Bhat, J. Ishwara; Alva, Vijaya D. P.

2014-01-01

The corrosion behavior of aluminum and mild steel in hydrochloric acid medium was studied using a nicotinic acid hydrazide as inhibitor by potentiodynamic polarization, electrochemical impedance spectroscopy technique and gravimetric methods. The effects of inhibitor concentration and temperature were investigated. The experimental results suggested, nicotinic acid hydrazide is a good corrosion inhibitor for both aluminum and mild steel in hydrochloric acid medium and the inhibition efficiency increased with increase in the inhibitor concentration. The polarization studies revealed that nicotinic acid hydrazide exhibits mixed type of inhibition. The inhibition was assumed to occur via adsorption of the inhibitor molecules on the aluminum and mild steel surface and inhibits corrosion by blocking the reaction sites on the surface of aluminum

Dilute-acid hydrolysis of apple, orange, apricot and peach pomaces as potential candidates for bioethanol production

OpenAIRE

Üçüncü, Can; Tarı, Canan; Demir, Hande; Büyükkileci, Ali Oğuz; Özen, Banu

2013-01-01

Chemical composition of four selected fruit pomaces (agro-industrial wastes) was evaluated. The effect of temperature, time, acid concentration and solid:liquid (S:L) ratio on dilute-acid hydrolysis of selected pomaces were investigated using 24 factorial and central composite design and optimum hydrolysis conditions were determined. A preliminary study was initiated using apple hydrolysate and the fungus Tricoderma harzianum in order to explore and demonstrate their potential uses in bioetha...

Synthesis of Furfural from Water Hyacinth (Eichornia croassipes)

Science.gov (United States)

Ismiyarto; Ngadiwiyana; windarti, T.; Purbowatiningrum, RS; Hapsari, M.; Rafi'ah, FH; Suyanti; Haq, MS

2017-02-01

Furfural has been prepared from hydrolysis of dried biomass of water hyacinth (Eichornia crassipes) by using diluted hydrochloric acid and sulphuric acid as catalysts. This process involved the conversion of the pentosane fraction in water hyacinth into pentose, and then pentose was cyclodehydrated into furfural. The reaction was conducted in a distillation set with receiving the flask that contains chloroform. Furfural was identified by fehling test which was then characterized using Fourier Transform Infra Red (FTIR) and Proton Nuclear Magnetic Resonance (1H-NMR), followed by Gas Chromatography with Mass Spectroscopy (GC-MS). The yield of furfural obtained using sulphuric acid catalyst was 0.38% and hydrochloric acid catalyst was 0.01% of dried biomass.

Preliminary Study on the Kinetics and Mechanism of the Oxidation of Naphthol Green B by Dichromate Ion in Aqueous Hydrochloric Acid Medium

Directory of Open Access Journals (Sweden)

Bako Myek

2014-04-01

Full Text Available The kinetics of the oxidation of naphthol green B (NGB3- by Cr2O7 2- has been studied in aqueous hydrochloric acid medium at an ionic strength, I = 0.50 mol dm-3 (NaCl, H+ =1.0  10-4 mol dm-3 (HCl and T = 25  1C. The redox reaction displayed a stoichiometry of 1:1 and obeys the rate law: -dNGB3-/dt = k2NGB3-]Cr2O7 2- . The second order rate constant increases with increase in acid concentration and in the ionic strength of reaction medium. The rates of reaction displayed a positive salt effect. Addition of acrylonitrile to a partially reacted mixture in the presence of excess methanol did not lead to gel formation. Added cations and anions inhibited the naphthol green B - Cr2O7 2- reaction. Results of the Michaelis – Menten plot gave no evidence of intermediate complex formation during the course of the reaction. Based on the results obtained, the reaction is believed to proceed through the outersphere mechanistic pathway.

Dilute acid pretreatment of rye straw and bermudagrass for ethanol production

Energy Technology Data Exchange (ETDEWEB)

Ye Sun; Jay J Cheng [North Carolina State Univ., Dept. of Biological and Agricultural Engineering, Raleigh, NC (United States)

2005-09-01

Ethanol production from lignocellulosic materials provides an alternative energy production system. Rye and bermudagrass that are used in hog farms for nutrient uptake from swine wastewater have the potential for fuel ethanol production because they have a relative high cellulose and hemicellulose content. Dilute sulfuric acid pretreatment of rye straw and bermudagrass before enzymatic hydrolysis of cellulose was investigated in this study. The biomass at a solid loading rate of 10% was pretreated at 121 deg C with different sulfuric acid concentrations (0.6, 0.9, 1.2 and 1.5%, w/w) and residence times (30, 60, and 90 min). Total reducing sugars, arabinose, galactose, glucose, and xylose in the prehydrolyzate were analyzed. In addition, the solid residues were hydrolyzed by cellulases to investigate the enzymatic digestibility. With the increasing acid concentration and residence time, the amount of arabinose and galactose in the filtrates increased. The glucose concentration in the prehydrolyzate of rye straw was not significantly influenced by the sulfuric acid concentration and residence time, but it increased in the prehydrolyzate of bermudagrass with the increase of pretreatment severity. The xylose concentration in the filtrates increased with the increase of sulfuric acid concentration and residence time. Most of the arabinan, galactan and xylan in the biomass were hydrolyzed during the acid pretreatment. Cellulose remaining in the pretreated feedstock was highly digestible by cellulases from Trichoderma reesei. (Author)

Dissolution of magnetite in a dilute chemical decontaminant formulation containing gallic acid as a reductant

International Nuclear Information System (INIS)

Kishore, Kamal; Rajesh, Puspalata; Dey, G.R.

2000-01-01

Gallic acid (GA) was tried as a reductant in place of ascorbic acid in dilute chemical decontaminant (DCD) formulations. Dissolution of magnetite in GA based DCD formulations was studied at 50 deg as well as 80 degC. It was found to be a good substitute for ascorbic acid in EDTA/ascorbic acid/citric acid i.e. EAC formulation. The efficiency of EDTA/GA/CA formulation was as good as that of EAC formulation. 2.8 was found to be the optimum pH for this formulation and dissolution decreased at lower as well as higher pHs. The ion-exchange behaviour of GA is also appropriate for using it in a regenerating type of formulation. Being an aromatic compound, gallic acid has inherent stability against radiation degradation. (author)

Separation of glycols from dilute aqueous solutions via complexation with boronic acids

Energy Technology Data Exchange (ETDEWEB)

Randel, L.A.; King, C.J.

1991-07-01

This work examines methods of separating low molecular weight glycols from dilute aqueous solution. Extraction into conventional solvents is generally not economical, since, in the literature reviewed, distribution ratios for the two- to four-carbon glycols are all less than one. Distribution ratios can be increased, however, by incorporating into the organic phase an extracting agent that will complex with the solute of interest. The extracting agent investigated in this work is 3-nitrophenylboronic acid (NPBA). NPBA, a boric acid derivative, reversibly complexes with many glycols. The literature on complexation of borate and related compounds with glycols, including mechanistic data, measurement techniques, and applications to separation processes, provides information valuable for designing experiments with NPBA and is reviewed herein. 88 refs., 15 figs., 24 tabs.

Titanium leaching from red mud by diluted sulfuric acid at atmospheric pressure

International Nuclear Information System (INIS)

Agatzini-Leonardou, S.; Oustadakis, P.; Tsakiridis, P.E.; Markopoulos, Ch.

2008-01-01

Laboratory-scale research has focused on the recovery of titanium from red mud, which is obtained from bauxite during the Bayer process for alumina production. The leaching process is based on the extraction of this element with diluted sulfuric acid from red mud under atmospheric conditions and without using any preliminary treatment. Statistical design and analysis of experiments were used, in order to determine the main effects and interactions of the leaching process factors, which were: acid normality, temperature and solid to liquid ratio. The titanium recovery efficiency on the basis of red mud weight reached 64.5%. The characterization of the initial red mud, as well as this of the leached residues was carried out by X-ray diffraction, TG-DTA and scanning electron microscopy

Fermentative utilization of glycerol residue for the production of acetic acid

Science.gov (United States)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

Beech wood Fagus sylvatica dilute-acid hydrolysate as a feedstock to support Chlorella sorokiniana biomass, fatty acid and pigment production.

Science.gov (United States)

Miazek, Krystian; Remacle, Claire; Richel, Aurore; Goffin, Dorothee

2017-04-01

This work evaluates the possibility of using beech wood (Fagus sylvatica) dilute-acid (H 2 SO 4 ) hydrolysate as a feedstock for Chlorella sorokiniana growth, fatty acid and pigment production. Neutralized wood acid hydrolysate, containing organic and mineral compounds, was tested on Chlorella growth at different concentrations and compared to growth under phototrophic conditions. Chlorella growth was improved at lower loadings and inhibited at higher loadings. Based on these results, a 12% neutralized wood acid hydrolysate (Hyd12%) loading was selected to investigate its impact on Chlorella growth, fatty acid and pigment production. Hyd12% improved microalgal biomass, fatty acid and pigment productivities both in light and in dark, when compared to photoautotrophic control. Light intensity had substantial influence on fatty acid and pigment composition in Chlorella culture during Hyd12%-based growth. Moreover, heterotrophic Chlorella cultivation with Hyd12% also showed that wood hydrolysate can constitute an attractive feedstock for microalgae cultivation in case of lack of light. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cotton nanofibers obtained by different acid conditions

International Nuclear Information System (INIS)

Teixeira, Eliangela de M.; Oliveira, Caue Ribeiro de; Mattoso, Luiz H.C.; Correa, Ana Carolina; Palladin, Priscila

2009-01-01

The thermal stability of cellulose nanofibers is related to their application and especially to polymer processing which temperatures of processing are around 200 deg C. In this work, nanofibers of commercial cotton were obtained by acid hydrolysis employing different acids: sulfuric, hydrochloric and a mixture (2:1; sulfuric acid: hydrochloric acid).The morphology of the nanofibers were characterized by transmission microscopy (TEM), crystallinity by x-ray diffraction (XRD) and thermal stability in air atmosphere by thermogravimetric analysis (TGA). The results indicated a very similar morphology and crystallinity among them. The main differences were relative to aggregation state e and thermal stability. The aggregation state of the suspensions decreases in the order HCl 2 SO 4 :HCl 2 SO 4- . The hydrolysis with a mix of HCl and H 2 SO 4 resulted in cellulose nanofibers with higher thermal stability than those hydrolyzed with H 2 SO 4 . The hydrolysis employed with a mixture of sulphuric and hydrochloric acids also showed a better dispersion than those suspensions of nanofibers obtained by hydrolysis with only HCl. (author)

Rare earth element recycling from waste nickel-metal hydride batteries.

Science.gov (United States)

Yang, Xiuli; Zhang, Junwei; Fang, Xihui

2014-08-30

With an increase in number of waste nickel-metal hydride batteries, and because of the importance of rare earth elements, the recycling of rare earth elements is becoming increasingly important. In this paper, we investigate the effects of temperature, hydrochloric acid concentration, and leaching time to optimize leaching conditions and determine leach kinetics. The results indicate that an increase in temperature, hydrochloric acid concentration, and leaching time enhance the leaching rate of rare earth elements. A maximum rare earth elements recovery of 95.16% was achieved at optimal leaching conditions of 70°C, solid/liquid ratio of 1:10, 20% hydrochloric acid concentration, -74μm particle size, and 100min leaching time. The experimental data were best fitted by a chemical reaction-controlled model. The activation energy was 43.98kJ/mol and the reaction order for hydrochloric acid concentration was 0.64. The kinetic equation for the leaching process was found to be: 1-(1-x)(1/3)=A/ρr0[HCl](0.64)exp-439,8008.314Tt. After leaching and filtration, by adding saturated oxalic solution to the filtrate, rare earth element oxalates were obtained. After removing impurities by adding ammonia, filtering, washing with dilute hydrochloric acid, and calcining at 810°C, a final product of 99% pure rare earth oxides was obtained. Copyright © 2014 Elsevier B.V. All rights reserved.

Recovery of acids from dilute streams : A review of process technologies

International Nuclear Information System (INIS)

Talnikar, Vivek Digambar; Mahajan, Yogesh Shankar

2014-01-01

Chemical process industries convert raw materials into useful products. Acids, among other chemicals, are used in many industries as reactants, solvents and also as catalysts in a few instances as well. Resulting streams are dilute, from which the acids must be recovered. For recovery, many technologies can be used by which acids can be regained as such or can be converted into other value-added products like esters. Membrane processes and biological processes are being researched academically and practiced industrially. These have their own advantages and disadvantages in view of conversion, energy consumption etc. These are not always advantageous and hence an alternate process technology is necessary like reactive separation (RS). RS is advantageous especially when the acid is to be converted to other useful products by reaction, due to additional advantages or because no other technology is well suited or due to cost considerations alone. Conventional process technologies use the reactor configuration followed by the subsequent separation sequence. This approach can sometimes suffer from lesser conversion, difficulties in separation etc. To overcome these problems, RS has an edge over other processes in terms of the recovery of the useful compounds. Reactive distillation (RD), reactive extraction (RE) and reactive chromatography (RC) are the separation technologies that can be useful for acid recovery in an economically feasible way. This review covers the various processes of acid recovery along with the recent work in the field of reactive separations

Performance of Different Acids on Sandstone Formations

Directory of Open Access Journals (Sweden)

M. A. Zaman

2013-12-01

Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

Gold Cleaning Methods for Electrochemical Detection Applications

DEFF Research Database (Denmark)

Fischer, Lee MacKenzie; Tenje, Maria; Heiskanen, Arto

2009-01-01

; hydrochloric acid potential cycling; dimethylamine borane reducing agent solutions at 25 and 65 degrees C; and a dilute form of Aqua Regia. Peak-current potential-differences obtained from cyclic voltammetry and charge transfer resistance obtained from electrochemical impedance spectroscopy, as well as X...

Designing of high-resolution photoresists: use of modern NMR ...

Indian Academy of Sciences (India)

Unknown

Novolac copolymers were prepared by both one- and two- step procedures ... ture was diluted with hydrochloric acid (1 : 1) in an ice bath and the ..... spectrum of the negative photoresist. The almost super-. +. O. N2. SO2. O. O. DNQO. DNQO.

The urinary excretion of orotic acid and orotidine, measured by an isotope dilution assay

International Nuclear Information System (INIS)

Tax, W.J.M.; Veerkamp, J.H.; Schretlen, E.D.A.M.

1978-01-01

Unknown concentrations of orotic acid can be measured by competition with a known amount of [carboxyl- 14 C]orotic acid for reaction with a limiting amount of phosphoribosylpyrophosphate in the presence of orotate phosphoribosyltransferase and orotidine monophosphate decarboxylase. The dilution of the specific radioactivity in the product 14 CO 2 is a sensitive and accurate measure of the amount of orotic acid present in the sample. Orotidine can also be determined after hydrolytic cleavage to orotic acid. The method was used to measure orotic acid and orotidine in urine samples from newborns, healthy controls and patients with gout or deficiency of hypoxanthine-guanine phosphoribosyltransferase receiving allopurinol. Urinary excretion of orotic acid and orotidine in newborns was similar whether the infants were breast-fed or received milk powder. The excretion of orotidine was increased in all patients receiving allopurinol. After allopurinol administration orotic acid excretion was increased in gouty patients but close to normal values in patients with deficiency of hypoxanthine-guanine phosphoribosyltransferase. The results are discussed in relation to the mechanism by which allopurinol inhibits pyrimidine metabolism. (Auth.)

Facile preparation of super-hydrophilic poly(ethylene terephthalate) fabric using dilute sulfuric acid under microwave irradiation

Energy Technology Data Exchange (ETDEWEB)

Xu, Fang [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China); Zhang, Guangxian, E-mail: zgx656472@sina.com.cn [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China); Zhang, Fengxiu [College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Zhang, Yuansong [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China)

2015-09-15

Highlights: • A durable super-hydrophilic PET fabric was prepared using dilute H{sub 2}SO{sub 4} under microwave irradiation. • Dilute sulfuric acid was gradually concentrated enough to sulfonate PET fabric. • Microwave irradiation made PET fabric modification highly efficient. • The mechanical properties of modified PET fibers were kept well. • The method was novel, rapid, and eco-friendly. - Abstract: The hydrophilicity of a poly(ethylene terephthalate) (PET) fabric was greatly modified by using dilute sulfuric acid, which gradually became concentrated enough to sulfonate the fabric when microwave irradiation (MW) was applied. The modified PET fabric was super-hydrophilic. Modifying the fabric caused the water contact angle to decrease from 132.46 (for the unmodified fabric) to 0°, the water absorption rate to increase from 36.45 to 119.78%, and the capillary rise height to increase from 0.4 to 14.4 cm. The hydrophilicity of the modified PET fabric was not affected by washing it many times. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed that there were sulfonic acid groups on the modified fibers. Almost no difference between the surfaces of the unmodified and modified PET fibers was found using scanning electron microscopy. Analysis by differential scanning calorimetry showed that the unmodified and modified fabrics had similar thermostabilities. X-ray diffraction analysis of the crystalline structures of the unmodified and modified fibers showed that they were almost the same. The strength, elasticity, and rigidity of the unmodified fabric were retained by the modified fabric. The modified fabric had better dyeing properties than the unmodified fabric.

Structural features of dilute acid, steam exploded, and alkali pretreated mustard stalk and their impact on enzymatic hydrolysis.

Science.gov (United States)

Kapoor, Manali; Raj, Tirath; Vijayaraj, M; Chopra, Anju; Gupta, Ravi P; Tuli, Deepak K; Kumar, Ravindra

2015-06-25

To overcome the recalcitrant nature of biomass several pretreatment methodologies have been explored to make it amenable to enzymatic hydrolysis. These methodologies alter cell wall structure primarily by removing/altering hemicelluloses and lignin. In this work, alkali, dilute acid, steam explosion pretreatment are systematically studied for mustard stalk. To assess the structural variability after pretreatment, chemical analysis, surface area, crystallinity index, accessibility of cellulose, FT-IR and thermal analysis are conducted. Although the extent of enzymatic hydrolysis varies upon the methodologies used, nevertheless, cellulose conversion increases from adsorption capacity. However, no such relationship is observed for xylose yield. Mass balance of the process is also studied. Dilute acid pretreatment is the best methodology in terms of maximum sugar yield at lower enzyme loading. Copyright © 2015 Elsevier Ltd. All rights reserved.

Dilute chemical decontamination program review

International Nuclear Information System (INIS)

Anstine, L.D.; Blomgren, J.C.; Pettit, P.J.

1980-01-01

The objective of the Dilute Chemical Decontamination Program is to develop and evaluate a process which utilizes reagents in dilute concentrations for the decontamination of BWR primary systems and for the maintenance of dose rates on the out-of-core surfaces at acceptable levels. A discussion is presented of the process concept, solvent development, advantages and disadvantages of reagent systems, and VNC loop tests. Based on the work completed to date it is concluded that (1) rapid decontamination of BWRs using dilute reagents is feasible; (2) reasonable reagent conditions for rapid chemical decontamination are: 0.01M oxalic acid + 0.005M citric acid, pH3.0, 90/degree/C, 0.5 to 1.0 ppm dissolved oxygen; (3) control of dissolved oxygen concentration is important, since high levels suppress the rate of decontamination and low levels allow precipitation of ferrous oxalate. 4 refs

Behavior of GaSb (100) and InSb (100) surfaces in the presence of H{sub 2}O{sub 2} in acidic and basic cleaning solutions

Energy Technology Data Exchange (ETDEWEB)

Seo, Dongwan; Na, Jihoon; Lee, Seunghyo; Lim, Sangwoo, E-mail: swlim@yonsei.ac.kr

2017-03-31

Highlights: • Surface behavior of GaSb and InSb was investigated in acidic and basic solutions. • H{sub 2}O{sub 2} plays a key role in the surface oxidation of GaSb and InSb in acidic hydrochloric acid/hydrogen peroxide mixture (HPM) solution. • GaSb and InSb surfaces were hardly oxidized in basic ammonium hydroxide/hydrogen peroxide mixture (APM) solution in the presence of H{sub 2}O{sub 2}. • The effect of dilution of APM solution on the oxidation of the InSb surface was minimal. • Surface characteristics of GaSb and InSb in HPM and APM solutions are mainly determined by the behaviors of the group III elements rather than the group V element. - Abstract: Gallium antimonide (GaSb) and indium antimonide (InSb) have attracted strong attention as new channel materials for transistors due to their excellent electrical properties and lattice matches with various group III–V compound semiconductors. In this study, the surface behavior of GaSb (100) and InSb (100) was investigated and compared in hydrochloric acid/hydrogen peroxide mixture (HPM) and ammonium hydroxide/hydrogen peroxide mixture (APM) solutions. In the acidic HPM solution, surface oxidation was greater and the etching rates of the GaSb and InSb surfaces increased when the solution is concentrated, which indicates that H{sub 2}O{sub 2} plays a key role in the surface oxidation of GaSb and InSb in acidic HPM solution. However, the GaSb and InSb surfaces were hardly oxidized in basic APM solution in the presence of H{sub 2}O{sub 2} because gallium and indium are in the thermodynamically stable forms of H{sub 2}GaO{sub 3}{sup −} and InO{sub 2}{sup −}, respectively. When the APM solution was diluted, however, the Ga on the GaSb surface was oxidized by H{sub 2}O, increasing the etching rate. However, the effect of dilution of the APM solution on the oxidation of the InSb surface was minimal; thus, the InSb surface was less oxidized than the GaSb surface and the change in the etching rate of In

Dilute Sulfuric Acid Pretreatment of Agricultural and Agro-Industrial Residues for Ethanol Production

Science.gov (United States)

Martin, Carlos; Alriksson, Björn; Sjöde, Anders; Nilvebrant, Nils-Olof; Jönsson, Leif J.

The potential of dilute-acid prehydrolysis as a pretreatment method for sugarcane bagasse, rice hulls, peanut shells, and cassava stalks was investigated. The prehydrolysis was performed at 122°C during 20, 40, or 60 min using 2% H2SO4 at a solid-to-liquid ratio of 1∶10. Sugar formation increased with increasing reaction time. Xylose, glucose, arabinose, and galactose were detected in all of the prehydrolysates, whereas mannose was found only in the prehydrolysates of peanut shells and cassava stalks. The hemicelluloses of bagasse were hydrolyzed to a high-extent yielding concentrations of xylose and arabinose of 19.1 and 2.2 g/L, respectively, and a xylan conversion of more than 80%. High-glucose concentrations (26-33.5 g/L) were found in the prehydrolysates of rice hulls, probably because of hydrolysis of starch of grain remains in the hulls. Peanut shells and cassava stalks rendered low amounts of sugars on prehydrolysis, indicating that the conditions were not severe enough to hydrolyze the hemicelluloses in these materials quantitatively. All prehydrolysates were readily fermentable by Saccharomyces cerevisiae. The dilute-acid prehydrolysis resulted in a 2.7-to 3.7-fold increase of the enzymatic convertibility of bagasse, but was not efficient for improving the enzymatic hydrolysis of peanut shells, cassava stalks, or rice hulls.

Development and validation of an SPE HG-AAS method for determination of inorganic arsenic in samples of marine origin

DEFF Research Database (Denmark)

Rasmussen, Rie Romme; Hedegaard, Rikke Susanne Vingborg; Larsen, Erik Huusfeldt

2012-01-01

The present paper describes a novel method for the quantitative determination of inorganic arsenic (iAs) in food and feed of marine origin. The samples were subjected to microwave-assisted extraction using diluted hydrochloric acid and hydrogen peroxide, which solubilised the analytes and oxidised...

Changes in lignocellulosic supramolecular and ultrastructure during dilute acid pretreatment of Populus and switchgrass

International Nuclear Information System (INIS)

Foston, Marcus; Ragauskas, Art J.

2010-01-01

Dilute acid pretreatment (DAP) is commonly employed prior to enzymatic deconstruction of cellulose to increase overall sugar and subsequent ethanol yields from downstream bioconversion processes. Typically optimization of pretreatment is evaluated by determining hemicellulose removal, subsequent reactivity towards enzymatic deconstruction, and recoverable polysaccharide yields. In this study, the affect of DAP on the supramolecular and ultrastructure of lignocellulosic biomass was evaluated. A series of dilute acidic pretreatments, employing ∼0.10-0.20 mol/m 3 H 2 SO 4 at ∼160-180 o C, for varying residence times were conducted on both Populus and switchgrass samples. The untreated and pretreated biomass samples were characterized by carbohydrate and lignin analysis, gel permeation chromatography (GPC) and 13 C cross polarization magic angle spinning (CPMAS) NMR spectroscopy. GPC analysis shows a reduction in the molecular weight of cellulose and change in its polydispersity index (PDI) with increasing residence time, indicating that pretreatment is actually degrading the cellulose chains. 13 C CPMAS and non-linear line-fitting of the C 4 region in the carbon spectrum of the isolated cellulose not only showed that the crystallinity index increases with residence time, but that the lateral fibril dimension (LFD) and lateral fibril aggregate dimension (LFAD) increase as well.

Solvent extraction of no-carrier-added 103Pd from irradiated rhodium target with α-furyldioxime

International Nuclear Information System (INIS)

Mahdi Sadeghi; Behrouz Shirazi; Nami Shadanpour

2006-01-01

Solvent extraction of no-carrier-added 103 Pd was investigated from irradiated rhodium target with a-furyldioxime in chloroform from diluted hydrochloric acid. Extraction yield was 85.3% for a single extraction from 0.37M HCl and 103 Pd purity was better than 99%. (author)

Understanding longitudinal wood fiber ultra-structure for producing cellulose nanofibrils using disk milling with diluted acid prehydrolysis

Science.gov (United States)

Yanlin Qin; Xueqing Qiu; Junyong Zhu

2016-01-01

Here we used dilute oxalic acid to pretreat a kraft bleached Eucalyptus pulp (BEP) fibers to facilitate mechanical fibrillation in producing cellulose nanofibrils using disk milling with substantial mechanical energy savings. We successfully applied a reaction kinetics based combined hydrolysis factor (CHFx) as a severity factor to quantitatively...

The impacts of pretreatment on the fermentability of pretreated lignocellulosic biomass: a comparative evaluation between ammonia fiber expansion and dilute acid pretreatment

Directory of Open Access Journals (Sweden)

Dale Bruce E

2009-12-01

Full Text Available Abstract Background Pretreatment chemistry is of central importance due to its impacts on cellulosic biomass processing and biofuels conversion. Ammonia fiber expansion (AFEX and dilute acid are two promising pretreatments using alkaline and acidic pH that have distinctive differences in pretreatment chemistries. Results Comparative evaluation on these two pretreatments reveal that (i AFEX-pretreated corn stover is significantly more fermentable with respect to cell growth and sugar consumption, (ii both pretreatments can achieve more than 80% of total sugar yield in the enzymatic hydrolysis of washed pretreated solids, and (iii while AFEX completely preserves plant carbohydrates, dilute acid pretreatment at 5% solids loading degrades 13% of xylose to byproducts. Conclusion The selection of pretreatment will determine the biomass-processing configuration, requirements for hydrolysate conditioning (if any and fermentation strategy. Through dilute acid pretreatment, the need for hemicellulase in biomass processing is negligible. AFEX-centered cellulosic technology can alleviate fermentation costs through reducing inoculum size and practically eliminating nutrient costs during bioconversion. However, AFEX requires supplemental xylanases as well as cellulase activity. As for long-term sustainability, AFEX has greater potential to diversify products from a cellulosic biorefinery due to lower levels of inhibitor generation and lignin loss.

Selection of anion exchangers for detoxification of dilute-acid hydrolysates from spruce.

Science.gov (United States)

Horváth, Ilona Sárvári; Sjöde, Anders; Nilvebrant, Nils-Olof; Zagorodni, Andrei; Jönsson, Leif J

2004-01-01

Six anion-exchange resins with different properties were compared with respect to detoxification of a dilute-acid hydrolysate of spruce prior to ethanolic fermentation with Saccharomyces cerevisiae. The six resins encompassed strong and weak functional groups as well as styrene-, phenol-, and acrylic-based matrices. In an analytical experimental series, fractions from columns packed with the different resins were analyzed regarding pH, glucose, furfural, hydroxymethylfurfural, phenolic compounds, levulinic acid, acetic acid, formic acid, and sulfate. An initial adsorption of glucose occurred in the strong alkaline environment and led to glucose accumulation at a later stage. Acetic and levulinic acid passed through the column before formic acid, whereas sulfate had the strongest affinity. In a preparative experimental series, one fraction from each of six columns packed with the different resins was collected for assay of the fermentability and analysis of glucose, mannose, and fermentation inhibitors. The fractions collected from strong anion-exchange resins with styrene-based matrices displayed the best fermentability: a sevenfold enhancement of ethanol productivity compared with untreated hydrolysate. Fractions from a strong anion exchanger with acrylic-based matrix and a weak exchanger with phenol-based resin displayed an intermediate improvement in fermentability, a four- to fivefold increase in ethanol productivity. The fractions from two weak exchangers with styrene- and acrylic-based matrices displayed a twofold increase in ethanol productivity. Phenolic compounds were more efficiently removed by resins with styrene- and phenol-based matrices than by resins with acrylic-based matrices.

Converting Eucalyptus biomass into ethanol: Financial and sensitivity analysis in a co-current dilute acid process. Part II

International Nuclear Information System (INIS)

Gonzalez, R.; Treasure, T.; Phillips, R.; Jameel, H.; Saloni, D.; Wright, J.; Abt, R.

2011-01-01

The technical and financial performance of high yield Eucalyptus biomass in a co-current dilute acid pretreatment followed by enzymatic hydrolysis process was simulated using WinGEMS registered and Excel registered . Average ethanol yield per dry Mg of Eucalyptus biomass was approximately 347.6 L of ethanol (with average carbohydrate content in the biomass around 66.1%) at a cost of 0.49 L -1 of ethanol, cash cost of ∝0.46 L -1 and CAPEX of 1.03 L -1 of ethanol. The main cost drivers are: biomass, enzyme, tax, fuel (gasoline), depreciation and labor. Profitability of the process is very sensitive to biomass cost, carbohydrate content (%) in biomass and enzyme cost. Biomass delivered cost was simulated and financially evaluated in Part I; here in Part II the conversion of this raw material into cellulosic ethanol using the dilute acid process is evaluated. (author)

Interaction of magnesium diboride with HΛ2O, HΛ2OΛ2 and with acids

International Nuclear Information System (INIS)

Lyashenko, V.I.; Kosolapova, T.Ya.; Serebryakova, T.I.

1985-01-01

Chemical stability of magnesium diboride in some agressive media is investigated. It is shown that magnesium diboride possesses high chemical activity in relation to acids (nitric, phosphoric, hydrochloric, sulphuric). The fluohydric acid and hydrogen peroxide completely decompose magnesium boride. The kinetics of MgB 2 decomposition in aqueous solutions of acids (hydrochloric, sulphuric, nitric) and in water is studied. Activation energies and solubility rate constants are calculated

An overview the boron dilution issue in PWRs

International Nuclear Information System (INIS)

Hyvaerinen, J.

1994-01-01

The presentation is an overview of boron (boric acid) dilution in pressurized water reactors (PWRs). Boric acid has been widely used in PWRs as a dissolved poison, as one of the main reactivity controlling means, for a long time, from nearly but not quite from the beginning of the design, construction and operation of PWRs in the present-day sense. The specific safety issue, namely the risk of uncontrolled reactivity insertion due to inadvertent boron dilution, is discussed first, followed by a brief look on the history of boron usage in PWRs. A discussion of boron dilution phenomenology is presented next in general terms. Some particular concerns that boron dilution phenomena arouse in the minds of a regulator will also be presented before concluding with a brief look on the future of dissolved poisons. (11 refs.)

Rare earth element recycling from waste nickel-metal hydride batteries

International Nuclear Information System (INIS)

Yang, Xiuli; Zhang, Junwei; Fang, Xihui

2014-01-01

Highlights: • Leaching kinetics of REEs has rarely been reported. • A new method, including hydrochloric acid leaching and oxalic acid precipitation, was proposed. • REEs recovery rate of 95.16% and pure rare earth oxides of 99% were obtained. • Leaching process was controlled by chemical reaction. • The kinetic equation was determined. - Abstract: With an increase in number of waste nickel-metal hydride batteries, and because of the importance of rare earth elements, the recycling of rare earth elements is becoming increasingly important. In this paper, we investigate the effects of temperature, hydrochloric acid concentration, and leaching time to optimize leaching conditions and determine leach kinetics. The results indicate that an increase in temperature, hydrochloric acid concentration, and leaching time enhance the leaching rate of rare earth elements. A maximum rare earth elements recovery of 95.16% was achieved at optimal leaching conditions of 70 °C, solid/liquid ratio of 1:10, 20% hydrochloric acid concentration, −74 μm particle size, and 100 min leaching time. The experimental data were best fitted by a chemical reaction-controlled model. The activation energy was 43.98 kJ/mol and the reaction order for hydrochloric acid concentration was 0.64. The kinetic equation for the leaching process was found to be: 1−(1−x) 1/3 =A/ρr 0 [HCl] 0.64 exp((−439,800)/(8.314T) )t. After leaching and filtration, by adding saturated oxalic solution to the filtrate, rare earth element oxalates were obtained. After removing impurities by adding ammonia, filtering, washing with dilute hydrochloric acid, and calcining at 810 °C, a final product of 99% pure rare earth oxides was obtained

WO₃ nano-ribbons: their phase transformation from tungstite (WO₃·H₂O) to tungsten oxide (WO₃)

DEFF Research Database (Denmark)

Ahmadi, Majid; Sahoo, Satyaprakash; Younesi, Reza

2014-01-01

Tungsten oxide (WO3) nano-ribbons (NRs) were obtained by annealing tungstite (WO3·H2O) NRs. The latter was synthesized below room temperature using a simple, environmentally benign, and low cost aging treatment of precursors made by adding hydrochloric acid to diluted sodium tungstate solutions (...

A study of marine pollution caused by the release of metals into seawater following acid spills.

Science.gov (United States)

Cabon, Jean-Yves; Giamarchi, Philippe; Le Floch, Stephane

2010-07-01

This study examined the potential metal pollution induced by the accidental spill of different acids into seawater. The acids sink to the bottom according to their densities and subsequently react with marine sediments. The acids selected for this study were acetic, hydrochloric, nitric, sulfuric, and phosphoric acids; the metallic elements selected were Cr, Cu, Fe, Mn, Pb and Zn. The sediment was collected in Brest Harbour. The percentages of metals released from this sediment in the presence of various concentrations of acids in seawater were important; concentrations of approximately 7 mg L(-1) for Mn and 60 mg L(-1) for Zn were observed under our experimental conditions. We also examined the rate of release of these metals from the sediment into the seawater in the presence of the different acids and under different experimental conditions. We found that most of the metallic elements were released from the sediments into the seawater during the first fifteen minutes of exposure. After this time, a high degree of pollution was induced if acids leached into seawater were not rapidly diluted. Copyright 2010 Elsevier Ltd. All rights reserved.

Acid-base strengths in pyridine

NARCIS (Netherlands)

Bos, M.; Dahmen, E.A.M.F.

1971-01-01

Although pyridine is a solvent with a low dielectric constant, spectrophotometric determinations show simple dissociation without ion pairs as intermediates for some sulfonphthaleins and polynitrophenols in pyridine. The salts of a number of amines and hydrochloric acid, perchloric acid and picric

A sulfuric-lactic acid process for efficient purification of fungal chitosan with intact molecular weight.

Science.gov (United States)

Naghdi, Mitra; Zamani, Akram; Karimi, Keikhosro

2014-02-01

The most recent method of fungal chitosan purification, i.e., two steps of dilute sulfuric acid treatment, pretreatment of cell wall at room temperature for phosphate removal and extraction of chitosan from the phosphate free cell wall at high temperature, significantly reduces the chitosan molecular weight. This study was aimed at improvement of this method. In the pretreatment step, to choose the best conditions, cell wall of Rhizopus oryzae, containing 9% phosphate, 10% glucosamine, and 21% N-acetyl glucosamine, was treated with sulfuric, lactic, acetic, nitric, or hydrochloric acid, at room temperature. Sulfuric acid showed the best performance in phosphate removal (90%) and cell wall recovery (89%). To avoid depolymerisation of chitosan, hot sulfuric acid extraction was replaced with lactic acid treatment at room temperature, and a pure fungal chitosan was obtained (0.12 g/g cell wall). Similar pretreatment and extraction processes were conducted on pure shrimp chitosan and resulted in a chitosan recovery of higher than 87% while the reduction of chitosan viscosity was less than 15%. Therefore, the sulfuric-lactic acid method purified the fungal chitosan without significant molecular weight manipulation. Copyright © 2013 Elsevier B.V. All rights reserved.

The separation of trace elements in manganese dioxide

International Nuclear Information System (INIS)

Jones, E.A.; Dixon, K.

1981-01-01

Separations from manganese are discribed for (a)Al(III), Mo(VI), V(V), and Ti(IV), and (b)trace elements in general. In the first separation, a combined anion-cation exchange, the oxalate complexes are absorbed onto the anionic BIO.RAD 1-X8 resin. V(V) and Al(III) are then eluted into a cation-exchange column from which they are eluted successively, Mo(VI) and Ti(IV) then being eluted from the anionic resin. In the second separation, up to 2g of manganese is absorbed onto BIO.RAD AG 50W-X8 resin, from which V(V) is eluted with dilute hydrochloric acid prior to the elution of Co(II), Cu(II), Zn(II), Cd(II), Fe(III), As(III), Sb(III), Mo(VI), W(VI), and Sn(II) with a mixture of 1 M hydrochloric acid, 80 per cent acetone, and 0,1 per cent hydrogen peroxide. Mn(11) is eluted next with a mixture of 0,75M hydrochloric acid and 90 per cent acetone, after which the remaining cations are eluted with 4M hydrochloric acid. Satisfactory recoveries ranging from 0,8 to 60 mg/l were obtained for 18 of the 21 elements tested. After concentration by evaporation, final measurements were made by the use of atomic-absorption spectrophotometry, or direct-reading spectrometry with excitation from an inductively coupled plasma source. Comparative results were obtained with atomic-absorption procedures where the manganese was not separated. However, the separation procedure can reduce the time required for analysis by the direct method because it limits the number of dilutions necessary and eliminates the need for the use of the method of additions to compensate for interferences from manganese

Evaluation of various techniques for the pretreatment of sewage sludges prior to trace metal analysis by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Smith, R.

1983-01-01

Six techniques were evaluated for their suitability for the pretreatment of dried sewage sludge prior to trace metal analysis by atomic absorption spectrophotometry. The evaluation comprised analysis of two prepared samples of dried sludge for aluminium, cadmium, chromium, copper, iron, lead, manganese, nickel and zinc, after the following pretreatment: dry ashing at 500 degrees Celsius followed by extraction with dilute hydrochloric acid; dry ashing at 500 degrees Celsius followed by extraction with aqua regia; nitric acid digestion followed by extraction with hydrochloric acid; extraction with aqua regia; ashing with magnesium nitrate solution at 550 degrees Celsius followed by digestion with hydrochloric acid and extraction with nitric acid; extraction with nitric acid. Procedures involving the use of perchloric acid, hydrofluoric acid and hydrogen peroxide were not considered for reasons of safety. Except in the case of aluminium the direct mineral acid digestion and/or extraction methods generally gave higher recoveries than the procedures incorporating an ashing step. Direct extraction of the sample with aqua regia was recommended as a rapid and simple general method of sample pretreatment prior to analysis for all the metals investigated except aluminium. For this metal, more drastic sample pretreatment will be required, for example fusion or hydrofluoric acid digestion

Adsorption characteristics of lithium in sea water with coprecipitated alumina-magnesia gel

International Nuclear Information System (INIS)

Kaneko, Shoji; Takahashi, Wataru

1988-01-01

Alumina-magnesia mixed-oxide gel exhibited adsorptive ability for lithium in sea water attributed to weak acidic sites and micropores of diameter 20-30 A. The adsorption of lithium proceeded predominantly by the mechanism of ion-exchange, on which the facility was shown in the order of Na + > H + > NH 4 + . The elution of lithium adsorbed on the gel was complete with dilute hydrochloric acid. (author)

Application of a continuous twin screw-driven process for dilute acid pretreatment of rape straw.

Science.gov (United States)

Choi, Chang Ho; Oh, Kyeong Keun

2012-04-01

Rape straw, a processing residue generated from the bio-oil industry, was used as a model biomass for application of continuous twin screw-driven dilute acid pretreatment. The screw rotation speed and feeding rate were adjusted to 19.7rpm and 0.5g/min, respectively to maintain a residence time of 7.2min in the reaction zone, respectively. The sulfuric acid concentration was 3.5wt% and the reaction temperature was 165°C. The enzymatic digestibility of the glucan in the pretreated solids was 70.9%. The continuous process routinely gave around 28.8% higher yield for glucan digestibility than did the batch processing method. Copyright © 2012 Elsevier Ltd. All rights reserved.

In vivo synthesized 34S enriched amino acid standards for species specific isotope dilution of proteins

DEFF Research Database (Denmark)

Hermann, Gerrit; Moller, Laura Hyrup; Gammelgaard, Bente

2016-01-01

(ICP-MS) combined to anion exchange showed that very high concentrated spike material could be produced with [small mu ]mol amounts of proteinogenic sulfur containing amino acids per g cell dry weight. An enrichment of 34S to 96.3 +/- 0.4% (n = 3) and 98.5 +/- 0.4% (n = 3) for cysteic acid...... with the concept of species specific isotope dilution analysis (IDA). The method relies on the determination of the two sulfur containing amino acids, cysteine and methionine by sulfur speciation analysis and is hence applicable to any protein containing sulfur. In vivo synthesis using 34S as sulfur source...... and methionine sulfone, respectively, was assessed. The established IDA method was validated for the absolute quantification of commercially available lysozyme and ceruloplasmin standards including the calculation of a total combined uncertainty budget....

Evaluation of continuous ethanol fermentation of dilute-acid corn stover hydrolysate using thermophilic anaerobic bacterium Thermoanaerobacter BG1L1

DEFF Research Database (Denmark)

Georgieva, Tania I.; Ahring, Birgitte Kiær

2007-01-01

Dilute sulfuric acid pretreated corn stover is potential feedstock of industrial interest for second generation fuel ethanol production. However, the toxicity of corn stover hydrolysate (PCS) has been a challenge for fermentation by recombinant xylose fermenting organisms. In this work...

A whole cell biocatalyst for cellulosic ethanol production from dilute acid-pretreated corn stover hydrolyzates

Energy Technology Data Exchange (ETDEWEB)

Ryu, Seunghyun; Karim, Muhammad Nazmul [Texas Tech Univ., Lubbock, TX (United States). Dept. of Chemical Engineering

2011-08-15

In this research, a recombinant whole cell biocatalyst was developed by expressing three cellulases from Clostridium cellulolyticum - endoglucanase (Cel5A), exoglucanase (Cel9E), and {beta}-glucosidase - on the surface of the Escherichia coli LY01. The modified strain is identified as LY01/pRE1H-AEB. The cellulases were displayed on the surface of the cell by fusing with an anchor protein, PgsA. The developed whole cell biocatalyst was used for single-step ethanol fermentation using the phosphoric acid-swollen cellulose (PASC) and the dilute acid-pretreated corn stover. Ethanol production was 3.59 {+-} 0.15 g/L using 10 g/L of PASC, which corresponds to a theoretical yield of 95.4 {+-} 0.15%. Ethanol production was 0.30 {+-} 0.02 g/L when 1 g/L equivalent of glucose in the cellulosic fraction of the dilute sulfuric acid-pretreated corn stover (PCS) was fermented for 84 h. A total of 0.71 {+-} 0.12 g/L ethanol was produced in 48 h when the PCS was fermented in the simultaneous saccharification and co-fermentation mode using the hemicellulosic (1 g/L of total soluble sugar) and as well as the cellulosic (1 g/L of glucose equivalent) parts of PCS. In a control experiment, 0.48 g/L ethanol was obtained from 1 g/L of hemicellulosic PCS. It was concluded that the whole cell biocatalyst could convert both cellulosic and hemicellulosic substrates into ethanol in a single reactor. The developed C. cellulolyticum-E. coli whole cell biocatalyst also overcame the incompatible temperature problem of the frequently reported fungal-yeast systems. (orig.)

Inhibitor efficiency in long-time protection of steel tanks for the chemical surface preparation against local corrosion by process solutions containing hydrochloric acid; Inhibitorwirksamkeit beim Langzeitschutz von Stahlbehaeltern fuer die chemische Oberflaechenvorbereitung gegen oertliche Korrosion durch salzsaeurehaltige Prozessloesungen

Energy Technology Data Exchange (ETDEWEB)

Stieglitz, U.; Schulz, W.D. [Institut fuer Korrosionsschutz Dresden GmbH, Gostritzer Str. 61-63, D-01217 Dresden (Germany)

2004-02-01

The efficiency of prevailing acid inhibitors is examined by age hardening heavy tank-steel plates in technically usual hot-galvanizing solutions for 1000 hours. With acid inhibitors local corrosion emerged as shallow pit formation first and foremost in hydrochlorid acid pickles (20 g/l HCl) at ambient temperature as well as in cleaners containing hydrochloric acid (10-30 g/l HCl) at 40 C when other conditions also applied. Above all, local corrosion was produced if the inhibitor concentration became too low (0.2 g/l) in connection with a minimum hydrochloric acid concentration (10-30 g/l). However, oxidizing agents like iron(III)-ions (5-10 g/l), atmospheric oxygen and free chlorine (100-1000 mg/l) lead to local corrosion, too. Local corrosion did not emerge in rinse baths (2-10 g/l HCl) and fluxing material solutions of zinc chloride and ammonium chloride (pH value: 2.0-5.5). Here uniform corrosion developed. Acid inhibitors turned out to be very effective against uniform corrosion in the examined long-time period (inhibiting values up to 99%). (Abstract Copyright [2004], Wiley Periodicals, Inc.) [German] Die Wirksamkeit handelsueblicher Saeureinhibitoren wird durch eine Auslagerung von Grobblechen aus Behaelterstahl ueber 1000 Stunden in technisch gebraeuchlichen Loesungen der Feuerverzinkung untersucht. Oertliche Korrosion ist als Muldenkorrosion in Gegenwart von Saeureinhibitoren vor allem in Salzsaeurebeizen (20 g/l HCl) bei Raumtemperatur und in salzsaeurehaltigen Reinigern (10-30 g/l HCl) bei 40 C aufgetreten, wenn Zusatzbedingungen erfuellt sind. Oertliche Korrosion wird vorwiegend durch eine Unterschreitung der Inhibitorkonzentration (0,2 g/l) in Verbindung mit einer minimalen Salzsaeurekonzentration (10-30 g/l) ausgeloest. Aber auch Oxidationsmittel wie Eisen(III)-Ionen (5-10 g/l), Luftsauerstoff und freies Chlor (100-1000 mg/l) fuehren zu oertlicher Korrosion. In Spuelbaedern (2-10 g/l HCl) und Flussmittelloesungen aus Zinkchlorid und Ammoniumchlorid (p

Determination of natural uranium in urine (233U)

International Nuclear Information System (INIS)

Jeanmaire, L.; Jammet, H.

1959-01-01

A procedure for the quantitative analysis of uranium in urine is described. The residue obtained by mineralization is dissolved in diluted hydrochloric acid. Uranium is separated by fixation on a permutit 50 column, elution with 0,2 M oxalic acid and electrodeposition on nickel. Uranium is then measured by α counting. It is thus possible to detect less than 1 pico-curie of uranium in the sample. (author) [fr

Investigation of cleaning reagents for calcium chromate spills

International Nuclear Information System (INIS)

Dillard, B.M.

1979-01-01

Cleaning of calcium chromate spills can be a problem due to the insolubility of the material and the corrosiveness of several possible cleaning agents on the stainless steel equipment. Because of OSHA Standards for Cr(VI) exposure, it is necessary to remove spills as efficiently as possible in order to prevent the contaminant from becoming airborne. This study involved the comparison of several possible cleaning agents by studying the solubility of calcium chromate in each reagent. Two general types of reagents for dissolution of calcium chromate were investigated; those which act by conversion of the insoluble calcium chromate to a more soluble salt and to H 2 CrO 4 , and those which appear to act as complexing agents and thereby dissolve the calcium chromate. The most efficient of the reagents investigated was hydrochloric acid. However, even dilute solutions of halide acids destroy passivity of stainless steel causing pitting and stress-corrosion. Acetic acid and nitric acid were somewhat less efficient than hydrochloric acid in dissolving calcium chromate. However, both reagents are noncorrosive with stainless steel, nitric acid tending to favor passivity of the materials. Therefore, it is recommended that dilute solutions of either of these two acids be used for removal of calcium chromate spills in conjunction with mechanical methods that might be necessary, depending on the magnitude of the spill

Kinetic characterization for hemicellulose hydrolysis of corn stover in a dilute acid cycle spray flow-through reactor at moderate conditions

International Nuclear Information System (INIS)

Jin, Qiang; Zhang, Hongman; Yan, Lishi; Qu, Liang; Huang, He

2011-01-01

The kinetic characterization of hemicellulose hydrolysis of corn stover was investigated using a new reactor of dilute acid cycle spray flow-through (DCF) pretreatment. The primary purpose was to obtain kinetic data for hemicellulose hydrolysis with sulfuric acid concentrations (10-30 kg m -3 ) at relatively low temperatures (90-100 o C). A simplified kinetic model was used to describe its performance at moderate conditions. The results indicate that the rates of xylose formation and degradation are sensitive to flow rate, temperature and acid concentration. Moreover, the kinetic data of hemicellulose hydrolysis fit a first-order reaction model and the experimental data with actual acid concentration after accounting for the neutralization effect of the substrates at different temperatures. Over 90% of the xylose monomer yield and below 5.5% of degradation product (furfural) yield were observed in this reactor. Kinetic constants for hemicellulose hydrolysis models were analyzed by an Arrhenius-type equation, and the activation energy of xylose formation were 111.6 kJ mol -1 , and 95.7 kJ mol -1 for xylose degradation, respectively. -- Highlights: → Investigating a novel pretreatment reactor of dilute acid cycle spray flow-through. → Xylose yield is sensitive to flow rate, temperature and acid concentration. → Obtaining relatively higher xylose monomer yield and lower fermentation inhibitor. → Lumping hemicellulose and xylan oligmers together in the model is a valid way. → The kinetic model as a guide for reactor design, and operation strategy optimization.

Over production of fermentable sugar for bioethanol production from carbohydrate-rich Malaysian food waste via sequential acid-enzymatic hydrolysis pretreatment.

Science.gov (United States)

Hafid, Halimatun Saadiah; Nor 'Aini, Abdul Rahman; Mokhtar, Mohd Noriznan; Talib, Ahmad Tarmezee; Baharuddin, Azhari Samsu; Umi Kalsom, Md Shah

2017-09-01

In Malaysia, the amount of food waste produced is estimated at approximately 70% of total municipal solid waste generated and characterised by high amount of carbohydrate polymers such as starch, cellulose, and sugars. Considering the beneficial organic fraction contained, its utilization as an alternative substrate specifically for bioethanol production has receiving more attention. However, the sustainable production of bioethanol from food waste is linked to the efficient pretreatment needed for higher production of fermentable sugar prior to fermentation. In this work, a modified sequential acid-enzymatic hydrolysis process has been developed to produce high concentration of fermentable sugars; glucose, sucrose, fructose and maltose. The process started with hydrothermal and dilute acid pretreatment by hydrochloric acid (HCl) and sulphuric acid (H 2 SO 4 ) which aim to degrade larger molecules of polysaccharide before accessible for further steps of enzymatic hydrolysis by glucoamylase. A kinetic model is proposed to perform an optimal hydrolysis for obtaining high fermentable sugars. The results suggested that a significant increase in fermentable sugar production (2.04-folds) with conversion efficiency of 86.8% was observed via sequential acid-enzymatic pretreatment as compared to dilute acid pretreatment (∼42.4% conversion efficiency). The bioethanol production by Saccharomyces cerevisiae utilizing fermentable sugar obtained shows ethanol yield of 0.42g/g with conversion efficiency of 85.38% based on the theoretical yield was achieved. The finding indicates that food waste can be considered as a promising substrate for bioethanol production. Copyright © 2017. Published by Elsevier Ltd.

Separation of rare earths from solutions of phosphoric acid

International Nuclear Information System (INIS)

Jones, E.A.

1977-01-01

Rare earths are separated from 6M phosphoric acid by adsorption onto cation resin BIORAD AG50W-X8. The phosphoric acid is then washed from the column, and the rare earths are eluted with 4M hydrochloric acid

Mild-temperature dilute acid pretreatment for integration of first and second generation ethanol processes.

Science.gov (United States)

Nair, Ramkumar B; Kalif, Mahdi; Ferreira, Jorge A; Taherzadeh, Mohammad J; Lennartsson, Patrik R

2017-12-01

The use of hot-water (100°C) from the 1st generation ethanol plants for mild-temperature lignocellulose pretreatment can possibly cut down the operational (energy) cost of 2nd generation ethanol process, in an integrated model. Dilute-sulfuric and -phosphoric acid pretreatment at 100°C was carried out for wheat bran and whole-stillage fibers. Pretreatment time and acid type influenced the release of sugars from wheat bran, while acid-concentration was found significant for whole-stillage fibers. Pretreatment led up-to 300% improvement in the glucose yield compared to only-enzymatically treated substrates. The pretreated substrates were 191-344% and 115-300% richer in lignin and glucan, respectively. Fermentation using Neurospora intermedia, showed 81% and 91% ethanol yields from wheat bran and stillage-fibers, respectively. Sawdust proved to be a highly recalcitrant substrate for mild-temperature pretreatment with only 22% glucose yield. Both wheat bran and whole-stillage are potential substrates for pretreatment using waste heat from the 1st generation process for 2nd generation ethanol. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of sub-microgram amounts of selenium in geological materials by atomic-absorption spectrophotometry with electrothermal atomisation after solvent extraction

Science.gov (United States)

Sanzolone, R.F.; Chao, T.T.

1981-01-01

An atomic-absorption spectrophotometric method with electrothermal atomisation has been developed for the determination of selenium in geological materials. The sample is decomposed with a mixture of nitric, perchloric and hydrofluoric acids and heated with hydrochloric acid to reduce selenium to selenium (IV). Selenium is then extracted into toluene from a hydrochloric acid - hydrobromic acid medium containing iron. A few microlitres of the toluene extract are injected into a carbon rod atomiser, using a nickel solution as a matrix modifier. The limits of determination are 0.2-200 p.p.m. of selenium in a geological sample. For concentrations between 0.05 and 0.2 p.p.m., back-extraction of the selenium into dilute hydrochloric acid is employed before atomisation. Selenium values for reference samples obtained by replicate analysis are in general agreement with those reported by other workers, with relative standard deviations ranging from 4.1 to 8.8%. Recoveries of selenium spiked at two levels were 98-108%. Major and trace elements commonly encountered in geological materials do not interfere. Arsenic has a suppressing effect on the selenium signals, but only when its concentration is greater than 1000 p.p.m. Nitric acid interferes seriously with the extraction of selenium and must be removed by evaporation in the sample-digestion step.

The role of acid anion on the inhibition of the acidic corrosion of steel by lupine extract

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)], E-mail: ashrafmoustafa@yahoo.com; Abd-El-Nabey, B.A.; Saadawy, M. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)

2009-05-15

The inhibitive effect of lupine (Lupinous albus L.) extract on the corrosion of steel in aqueous solution of 1 M sulphuric and 2 M hydrochloric acids was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization curves indicated that the lupine extract acts as a mixed-type inhibitor. EIS measurements showed that the dissolution process is under activation control. The inhibition efficiency of the extract obtained from impedance and polarization measurements was in a good agreement and was found to increase with increasing concentration of the extract. The obtained results showed that, the lupine extract could serve as an effective inhibitor for the corrosion of steel in acid media and the extract was more effective in case of hydrochloric acid. Theoretical fitting of the corrosion data to the kinetic-thermodynamic model was tested to show the nature of adsorption.

Impact of recycling stillage on conversion of dilute sulfuric acid pretreated corn stover to ethanol.

Science.gov (United States)

Mohagheghi, Ali; Schell, Daniel J

2010-04-01

Both the current corn starch to ethanol industry and the emerging lignocellulosic biofuels industry view recycling of spent fermentation broth or stillage as a method to reduce fresh water use. The objective of this study was to understand the impact of recycling stillage on conversion of corn stover to ethanol. Sugars in a dilute-acid pretreated corn stover hydrolysate were fermented to ethanol by the glucose-xylose fermenting bacteria Zymomonas mobilis 8b. Three serial fermentations were performed at two different initial sugar concentrations using either 10% or 25% of the stillage as makeup water for the next fermentation in the series. Serial fermentations were performed to achieve near steady state concentration of inhibitors and other compounds in the corn stover hydrolysate. Little impact on ethanol yields was seen at sugar concentrations equivalent to pretreated corn stover slurry at 15% (w/w) with 10% recycle of the stillage. However, ethanol yields became progressively poorer as the sugar concentration increased and fraction of the stillage recycled increased. At an equivalent corn stover slurry concentration of 20% with 25% recycled stillage the ethanol yield was only 5%. For this microorganism with dilute-acid pretreated corn stover, recycling a large fraction of the stillage had a significant negative impact on fermentation performance. Although this finding is of concern for biochemical-based lignocellulose conversion processes, other microorganism/pretreatment technology combinations will likely perform differently. (c) 2009 Wiley Periodicals, Inc.

pH effect on the enthalpy of dilution and volumetric properties of protocatechuic acid at T = 298.15 K

International Nuclear Information System (INIS)

Zheng, Yan; Liu, Min; Wang, Yong; Wang, Chunmei; Sun, Dezhi; Wang, Bingquan

2014-01-01

Graphical abstract: The dilution thermal power of PCA in potassium phosphate buffer solutions at different pHs and apparent molar volumes were determined in order to investigate the interactions of PCA with the coexistent spicies. - Highlights: • Enthalpies of dilution and apparent molar volumes of PCA in PBS at different pHs were measured. • Enthalpic interaction coefficients, limiting partial molar volumes and experimental slopes of PCA were determined. • The pH dependence of the weak interactions in the investigated system was obtained. • (Solute + solvent) interactions and structure making/breaking ability of solutes in the given system were discussed. - Abstract: The enthalpies of dilution of protocatechuic acid, a natural anti-cancer substance, in sodium phosphate and potassium phosphate buffer solutions with different pH values were measured by using a mixing-flow microcalorimeter at T = 298.15 K. Densities of the pseudo binary system (phosphate buffer + protocatechuic acid) were also measured with a quartz vibrating-tube densimeter. The enthalpic interaction coefficients (h 2 , h 3 and h 4 ) were computed according to the McMillan–Mayer model. Apparent molar volumes of the system were calculated from the data of densities, which have been used to deduce limiting partial molar volumes (V ϕ 0 ) of protocatechuic acid at different pH values. The aim of the experiments and data process is to investigate the interaction between the molecules of the important drug and that of the drug molecule with coexistent species in aqueous solutions as well as the influences on these interactions of such factors as pH and ion strength. Change trends of the enthalpic pair wise interaction coefficient h 2 and V ϕ 0 of protocatechuic acid with pH increasing in the both phosphate buffer solutions were obtained. The thermodynamic properties, h 2 and V ϕ 0 in potassium phosphate buffer solutions were compared with those in sodium phosphate buffer solutions at

Dilution Confusion: Conventions for Defining a Dilution

Science.gov (United States)

Fishel, Laurence A.

2010-01-01

Two conventions for preparing dilutions are used in clinical laboratories. The first convention defines an "a:b" dilution as "a" volumes of solution A plus "b" volumes of solution B. The second convention defines an "a:b" dilution as "a" volumes of solution A diluted into a final volume of "b". Use of the incorrect dilution convention could affect…

Comparing oxidative and dilute acid wet explosion pretreatment of Cocksfoot grass at high dry matter concentration for cellulosic ethanol production

DEFF Research Database (Denmark)

Njoku, Stephen Ikechukwu; Uellendahl, Hinrich; Ahring, Birgitte Kiær

2013-01-01

into cellulose monomeric C6 sugars was achieved for WEx condition AC-E (180°C, 15 min, and 0.2% sulfuric acid). For that condition, the highest ethanol yield of 197 g/kg DM (97% of theoretical maximum value) was achieved for SSF process by Saccharomyces cerevisiae. However, the highest concentration...... of hemicellulose C5 sugars was found for WEx pretreatment condition O2-A (160°C, 15 min, and 6 bar O2) which means that the highest potential ethanol yield was found at this moderate pretreatment condition with oxygen added. Increasing the pretreatment temperature to 180–190°C with addition of oxygen or dilute...... was investigated for cellulosic ethanol production. The biomass raw materials were pretreated using wet explosion (WEx) at 25% dry matter concentration with addition of oxygen or dilute sulfuric acid. The enzymatic hydrolysis of cellulose was significantly improved after pretreatment. The highest conversion...

Pretreatment by radiation and acids of chaff and its effect on enzymatic hydrolysis of cellulose

International Nuclear Information System (INIS)

Kumakura, M.; Kaetsu, I.

1984-01-01

The effect of pretreatment by radiation and acids—sulfuric, hydrochloric and acetic—on the enzymatic hydrolysis of chaff was studied. The combination of radiation and acids accelerates subsequent crushing and enzymatic hydrolysis. The percentage of fine powder below 115 mesh, after the crushing and the glucose yield on subsequent enzymatic hydrolysis, increased with increasing acid concentration, treatment time and irradiation dose. Radiation and hydrochloric acid pretreatment was the most effective in giving a high glucose conversion yield (about 90%). Irradiation dose, acid concentration, treatment temperature and treatment time were 20 Mrad, 0·5%, 70°C, and 5 h, respectively

Rapid and Precise Measurement of Serum Branched-Chain and Aromatic Amino Acids by Isotope Dilution Liquid Chromatography Tandem Mass Spectrometry

OpenAIRE

Yang, Ruiyue; Dong, Jun; Guo, Hanbang; Li, Hongxia; Wang, Shu; Zhao, Haijian; Zhou, Weiyan; Yu, Songlin; Wang, Mo; Chen, Wenxiang

2013-01-01

BACKGROUND: Serum branched-chain and aromatic amino acids (BCAAs and AAAs) have emerged as predictors for the future development of diabetes and may aid in diabetes risk assessment. However, the current methods for the analysis of such amino acids in biological samples are time consuming. METHODS: An isotope dilution liquid chromatography tandem mass spectrometry (ID-LC/MS/MS) method for serum BCAAs and AAAs was developed. The serum was mixed with isotope-labeled BCAA and AAA internal standar...

The sorption of acids in cellular side of apple pressing

International Nuclear Information System (INIS)

Asoev, M.G.; Mukhiddinov, Z.K.

1994-01-01

Equilibrium swell of sample refuse after separation of water is use for study of sorption of hydrochloric acid. Quantity adsorb acids set a price to difference her concentration before and after equilibrium sorption

A comparative evaluation of a dipicolinic acid based dilute chemical decontaminant formulation with respect to its efficacy for dissolution of iron oxides

Energy Technology Data Exchange (ETDEWEB)

Kamal Kishore; Dey, G.R.; Naik, D.B.; Moorthy, P.N. [Applied Chemistry Division, Bhabha Atomic Research Centre, Mumbai-400 085 (India)

1998-12-31

A dilute chemical decontamination formulation containing dipicolinic acid (2,6-pyridine dicarboxylic acid PDCA) and ascorbic acid (AA) has been found to be effective in dissolving magnetite, nickel ferrite and haemetite. Its main advantages arise because of (i) good solubility of the two constituents (ii) lack of absorption on the cation exchanger from acidic media during regenerative decontamination process (iii) stability to ionizing radiation and (iv) low corrosion rate for carbon steel. Dissolution rates of iron oxides in this formulation are as good as or better than in other well known formulations. (author)

Volumetric properties of ascorbic acid (vitamin C) and thiamine hydrochloride (vitamin B1) in dilute HCl and in aqueous NaCl solutions at (283.15, 293.15, 298.15, 303.15, 308.15, and 313.15) K

International Nuclear Information System (INIS)

Ayranci, Guler; Sahin, Melike; Ayranci, Erol

2007-01-01

Apparent molar volumes and apparent molar isentropic compressibilities of ascorbic acid (vitamin C) and thiamine hydrochloride (vitamin B 1 ) were determined from accurately measured density and sound velocity data in water and in aqueous NaCl solutions at (283.15, 293.15, 298.15, 303.15, 308.15, and 313.15) K. These volume and compressibility data were extrapolated to zero concentration using suitable empirical or theoretical equations to determine the corresponding infinite dilution values. Apparent molar expansibilities at infinite dilution were determined from slopes of apparent molar volume vs. temperature plots. Ionization of both ascorbic acid and thiamine hydrochloride were suppressed using sufficiently acidic solutions. Apparent molar volumes at infinite dilution for ascorbic acid and thiamine hydrochloride were found to increase with temperature in acidic solutions and in the presence of co-solute, NaCl. Apparent molar expansibility at infinite dilution were found to be constant over the temperature range studied and were all positive, indicating the hydrophilic character of the two vitamins studied in water and in the presence of co-solute, NaCl. Apparent molar isentropic compressibilities of ascorbic acid at infinite dilution were positive in water and in the presence of co-solute, NaCl, at low molalities. Those of thiamine hydrochloride at infinitive dilution were all negative, consistent with its ionic nature. Transfer apparent molar volumes of vitamins at infinite dilution from water solutions to NaCl solutions at various temperatures were determined. The results were interpreted in terms of complex vitamin-water-co-solute (NaCl) interactions

3-D Topo Surface Visualization of Acid-Base Species Distributions: Corner Buttes, Corner Pits, Curving Ridge Crests, and Dilution Plains

Science.gov (United States)

Smith, Garon C.; Hossain, Md Mainul

2017-01-01

Species TOPOS is a free software package for generating three-dimensional (3-D) topographic surfaces ("topos") for acid-base equilibrium studies. This upgrade adds 3-D species distribution topos to earlier surfaces that showed pH and buffer capacity behavior during titration and dilution procedures. It constructs topos by plotting…

Analysis of nifursol residues in turkey and chicken meat using liquid chromatography-tandem mass spectrometry

DEFF Research Database (Denmark)

Gabrielsen, Martin Vahl

2005-01-01

on conversion of nifursol and its metabolites with an intact 3,5-dinitrosalicylic acid hydrazide (DNSH) side chain to the 2-nitrophenyl analogue of nifursol (NPDNSH) by treatment with dilute hydrochloric acid and 2-nitrobenzaldehyde. Nifuroxazide (salicylic acid (5-nitrofurfurylidene) hydrazide) added......Nifursol (3,5-dinitrosalicylic acid (5-nitrofurfurylidene) hydrazide) is mainly used as a feed additive for the prevention of blackhead disease in turkeys. The objective of the present work was to establish information on nifursol residues in turkey and chicken meat. The analytical method was based...

Towards integrated biorefinery from dried distillers grains: Selective extraction of pentoses using dilute acid hydrolysis

International Nuclear Information System (INIS)

Fonseca, Dania A.; Lupitskyy, Robert; Timmons, David; Gupta, Mayank; Satyavolu, Jagannadh

2014-01-01

The abundant availability and high level of hemicellulose content make dried distillers grains (DDG) an attractive feedstock for production of pentoses (C5) and conversion of C5 to bioproducts. One target of this work was to produce a C5 extract (hydrolyzate) with high yield and purity with a low concentration of C5 degradation products. A high selectivity towards pentoses was achieved using dilute acid hydrolysis of DDG in a percolation reactor with liquid recirculation. Pretreatment of starting material using screening and ultrasonication resulted in fractional increase of the pentose yield by 42%. A 94% yield of pentoses on the DDG (280.9 g kg −1 ) was obtained. Selective extraction of individual pentoses has been achieved by using a 2-stage hydrolysis process, resulting in arabinose-rich (arabinose 81.5%) and xylose-rich (xylose 85.2%) streams. A broader impact of this work is towards an Integrated Bio-Refinery based on DDG – for production of biofuels, biochemical intermediates, and other bioproducts. - Highlights: • A process for selective extraction of pentoses from DDG was presented as a part of integrated biorefinery approach. • The selectivity for pentoses was high using dilute acid hydrolysis in a percolation reactor with liquid recirculation. • Pretreatment of DDG using screening and ultrasonication resulted in fractional increase of the pentose yield by 42 %. • A 94% yield in pentoses (280.9 g kg −1 of DDG) was obtained. • A 2-stage hydrolysis process, developed to extract individual pentoses, resulted in arabinose and xylose rich streams

Preparation of an sup(113m) indium generator

International Nuclear Information System (INIS)

Ling, H.W.

1979-01-01

This paper describes the features related to the preparation of sup(113m) In from a generator for nuclear medicine application. 113 Sn radioisotope is adsorbed on a hidrated zirconium oxide column and sup(113m) In generated from the decay of 113 Sn is eluted with diluted hydrochloric acid. This procedure is simple and appropriate for the separation of the desired radionuclide. Parameters which may affect the adsorption of 113 Sn like tin and hydrochloric acid concentration and temperature are studied. The influence of eluent concentration and temperature and flow rate of elution on sup(113m) In separation yields are observed. The purity of eluted sup(113m) In is analysed and variation of elution yield in a generator prepared with enriched tin is studied. (Author) [pt

Formic acid hydrolysis/liquid chromatography isotope dilution mass spectrometry: An accurate method for large DNA quantification.

Science.gov (United States)

Shibayama, Sachie; Fujii, Shin-Ichiro; Inagaki, Kazumi; Yamazaki, Taichi; Takatsu, Akiko

2016-10-14

Liquid chromatography-isotope dilution mass spectrometry (LC-IDMS) with formic acid hydrolysis was established for the accurate quantification of λDNA. The over-decomposition of nucleobases in formic acid hydrolysis was restricted by optimizing the reaction temperature and the reaction time, and accurately corrected by using deoxynucleotides (dNMPs) and isotope-labeled dNMPs as the calibrator and the internal standard, respectively. The present method could quantify λDNA with an expanded uncertainty of 4.6% using 10fmol of λDNA. The analytical results obtained with the present method were validated by comparing with the results of phosphate-base quantification by inductively coupled plasma-mass spectrometry (ICP-MS). The results showed good agreement with each other. We conclude that the formic acid hydrolysis/LC-IDMS method can quantify λDNA accurately and is promising as the primary method for the certification of DNA as reference material. Copyright © 2016 Elsevier B.V. All rights reserved.

MX Siting Investigation. Geotechnical Evaluation. Volume I. Arizona Verification Studies, FY 79, and Geotechnical Data, La Posa CDP, Arizona.

Science.gov (United States)

1979-11-15

INDEX 27-46 [2] 15 1260-5700 COMPRESSIONAL WAVE VELOCITY fps (mps) (384-1137) 1,61 HDA SHEAR STRENGTH DATA UNCONFINED COMPRESSION S, - ksf (kN. M2...carbonate; presence of calcium carbonate is commonly identified on the basis of reaction with dilute hydrochloric acid . CALICHE - Gravel, sand, or...pass through soil and/or rock material. pH - An index of the acidity or alkalinity of a soil in terms of the logarithm of the reciprocal of the

MX Siting Investigation Geotechnical Evaluation. Volume IB. Nevada-Utah Verification Studies, FY 79.

Science.gov (United States)

1979-08-24

Range. The southern tip of the range is composed of flows and intrusive masses of interme- diate to acidic composition (Cornwall, 1972). The east...suitable ’.7-10.0 18 O _(o. 2-3. [) 𔃼.2 NA [we 0] ,o,. 3: * [1 - Number of tests performed "CHARACTERISTICS OF SURFICIALAI SOIL: N HDA - No data available...commonly identified on the basis of reaction with dilute hydrochloric acid . CALICHE - Gravel, sand, or other material cemented principally by calcium

EFFECTIVENESS OF USING DILUTE OXALIC ACID TO DISSOLVE HIGH LEVEL WASTE IRON BASED SLUDGE SIMULANT

International Nuclear Information System (INIS)

Ketusky, E

2008-01-01

At the Savannah River Site (SRS), near Aiken South Carolina, there is a crucial need to remove residual quantities of highly radioactive iron-based sludge from large select underground storage tanks (e.g., 19,000 liters of sludge per tank), in order to support tank closure. The use of oxalic acid is planned to dissolve the residual sludge, hence, helping in the removal. Based on rigorous testing, primarily using 4 and 8 wt% oxalic acid solutions, it was concluded that the more concentrated the acid, the greater the amount of residual sludge that would be dissolved; hence, a baseline technology on using 8 wt% oxalic acid was developed. In stark contrast to the baseline technology, reports from other industries suggest that the dissolution will most effectively occur at 1 wt% oxalic acid (i.e., maintaining the pH near 2). The driver for using less oxalic acid is that less (i.e., moles) would decrease the severity of the downstream impacts (i.e., required oxalate solids removal efforts). To determine the initial feasibility of using 1 wt% acid to dissolve > 90% of the sludge solids, about 19,000 liters of representative sludge was modeled using about 530,000 liters of 0 to 8 wt% oxalic acid solutions. With the chemical thermodynamic equilibrium based software results showing that 1 wt% oxalic acid could theoretically work, simulant dissolution testing was initiated. For the dissolution testing, existing simulant was obtained, and an approximate 20 liter test rig was built. Multiple batch dissolutions of both wet and air-dried simulant were performed. Overall, the testing showed that dilute oxalic acid dissolved a greater fraction of the stimulant and resulted in a significantly larger acid effectiveness (i.e., grams of sludge dissolved/mole of acid) than the baseline technology. With the potential effectiveness confirmed via simulant testing, additional testing, including radioactive sludge testing, is planned

Pretreatment of Dried Distiller Grains with Solubles by Soaking in Aqueous Ammonia and Subsequent Enzymatic/Dilute Acid Hydrolysis to Produce Fermentable Sugars.

Science.gov (United States)

Nghiem, Nhuan P; Montanti, Justin; Kim, Tae Hyun

2016-05-01

Dried distillers grains with solubles (DDGS), a co-product of corn ethanol production in the dry-grind process, was pretreated by soaking in aqueous ammonia (SAA) using a 15 % w/w NH4OH solution at a solid/liquid ratio of 1:10. The effect of pretreatment on subsequent enzymatic hydrolysis was studied at two temperatures (40 and 60 °C) and four reaction times (6, 12, 24, and 48 h). Highest glucose yield of 91 % theoretical was obtained for the DDGS pretreated at 60 °C and 24 h. The solubilized hemicellulose in the liquid fraction was further hydrolyzed with dilute H2SO4 to generate fermentable monomeric sugars. The conditions of acid hydrolysis included 1 and 4 wt% acid, 60 and 120 °C, and 0.5 and 1 h. Highest yields of xylose and arabinose were obtained at 4 wt% acid, 120 °C, and 1 h. The fermentability of the hydrolysate obtained by enzymatic hydrolysis of the SAA-pretreated DDGS was demonstrated in ethanol fermentation by Saccharomyces cerevisiae. The fermentability of the hydrolysate obtained by consecutive enzymatic and dilute acid hydrolysis was demonstrated using a succinic acid-producing microorganism, strain Escherichia coli AFP184. Under the fermentation conditions, complete utilization of glucose and arabinose was observed, whereas only 47 % of xylose was used. The succinic acid yield was 0.60 g/g total sugar consumed.

Application of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry for children with hyperopia

Directory of Open Access Journals (Sweden)

Hong-Ping Yin

2016-02-01

Full Text Available AIM:To observe and study the comprehensive application effect of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry for children with hyperopia.METHODS:Eighty-four children with hyperopia who were intervened with mydriasis test and optometry in our hospital from February 2014 to March 2015 were selected as the research object,and they were intervened with mydriasis test and optometry by tropicamide or hydrochloric cyclopentolate eye drops. The diopter, pupil diameter and residual regulation before administration and at different time after administration of the two methods were compared,and the detected results of the two groups with different severity degree were compared too.RESULTS:The diopter, pupil diameter and residual regulation before administration of the two eye drops had no significant differences(all P>0.05,while the residual regulation after using hydrochloric cyclopentolate eye drops at 20, 40, 60min and 24h were all smaller than those after using tropicamide(all PP>0.05. The pupil diameter of the two groups at 48h after administration both had no significant differences to those before administration(all P>0.05.CONCLUSION:The comprehensive application effect of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry of children with hyperopia is better,and its paralysis effect for ciliaris is obvious.

Uracil in formic acid hydrolysates of deoxyribonucleic acid

Science.gov (United States)

Schein, Arnold H.

1966-01-01

1. When DNA is hydrolysed with formic acid for 30min. at 175° and the hydrolysate is chromatographed on paper with propan-2-ol–2n-hydrochloric acid, in addition to expected ultraviolet-absorbing spots corresponding to guanine, adenine, cytosine and thymine, an ultraviolet-absorbing region with RF similar to that of uracil can be detected. Uracil was separated from this region and identified by its spectra in acid and alkali, and by its RF in several solvent systems. 2. Cytosine, deoxyribocytidine and deoxyribocytidylic acid similarly treated with formic acid all yielded uracil, as did a mixture of deoxyribonucleotides. 3. Approx. 4% of deoxyribonucleotide cytosine was converted into uracil by the formic acid treatment. ImagesFig. 1. PMID:5949371

Incorporation of Mg and Ca into nanostructured Fe2O3 improves Fe solubility in dilute acid and sensory characteristics in foods.

Science.gov (United States)

Hilty, Florentine M; Knijnenburg, Jesper T N; Teleki, Alexandra; Krumeich, Frank; Hurrell, Richard F; Pratsinis, Sotiris E; Zimmermann, Michael B

2011-01-01

Iron deficiency is one of the most common micronutrient deficiencies worldwide. Food fortification can be an effective and sustainable strategy to reduce Fe deficiency but selection of iron fortificants remains a challenge. Water-soluble compounds, for example, FeSO(4), usually demonstrate high bioavailability but they often cause unacceptable sensory changes in foods. On the other hand, poorly acid-soluble Fe compounds, for example FePO(4), may cause fewer adverse sensory changes in foods but are usually not well bioavailable since they need to be dissolved in the stomach prior to absorption. The solubility and the bioavailability of poorly acid-soluble Fe compounds can be improved by decreasing their primary particle size and thereby increasing their specific surface area. Here, Fe oxide-based nanostructured compounds with added Mg or Ca were produced by scalable flame aerosol technology. The compounds were characterized by nitrogen adsorption, X-ray diffraction, transmission electron microscopy, and Fe solubility in dilute acid. Sensory properties of the Fe-based compounds were tested in 2 highly reactive, polyphenol-rich food matrices: chocolate milk and fruit yoghurt. The Fe solubility of nanostructured Fe(2)O(3) doped with Mg or Ca was higher than that of pure Fe(2)O(3). Since good solubility in dilute acid was obtained despite the inhomogeneity of the powders, inexpensive precursors, for example Fe- and Ca-nitrates, can be used for their manufacture. Adding Mg or Ca lightened powder color, while sensory changes when added to foods were less pronounced than for FeSO(4). The combination of high Fe solubility and low reactivity in foods makes these flame-made nanostructured compounds promising for food fortification. Practical Application: The nanostructured iron-containing compounds presented here may prove useful for iron fortification of certain foods; they are highly soluble in dilute acid and likely to be well absorbed in the gut but cause less severe

Corrosion Behaviour of Sn-based Lead-Free Solders in Acidic Solution

Science.gov (United States)

Nordarina, J.; Mohd, H. Z.; Ahmad, A. M.; Muhammad, F. M. N.

2018-03-01

The corrosion properties of Sn-9(5Al-Zn), Sn-Cu and SAC305 were studied via potentiodynamic polarization method in an acidic solution of 1 M hydrochloric acid (HCl). Sn-9(5Al-Zn) produced different polarization profile compared with Sn-Cu and SAC305. The morphological analysis showed that small, deep grooves shaped of corrosion product formed on top of Sn-9(5Al-Zn) solder while two distinctive structures of closely packed and loosely packed corrosion product formed on top of Sn-Cu and SAC305 solder alloys. Phase analysis revealed the formations of various corrosion products such as SnO and SnO2 mainly dominant on surface of solder alloys after potentiodynamic polarization in 1 M hydrochloric acid (HCl).

90Sr-90Y radionuclide generator based on ionex chromatography. Part 1 - project

International Nuclear Information System (INIS)

Miler, V.; Budsky, F.; Malek, Z.

2003-09-01

This part contains a proposal for the generator column design, materials to be used (chemicals, ionexes) and technological procedures. The proposal was inspired by the 90 Sr- 90 Y generator operated by Zfk Rossendorf. The aim was to develop and launch a generator for the preparation of carrier-free 90 Y in the form of [ 90 Y] chloride solution in dilute hydrochloric acid. The separation of Y from Sr is based on ionex chromatography by sorbing the two radionuclides on a catex. While Sr remains sorbed, 90 Y is eluted with lithium citrate. During this process, 90 Y is bonded in a citrate complex which, having a negative charge, is subsequently trapped by an anex. A guard column is inserted before the anex column to trap any traces of 90 Sr. 90 Y is eluted from the anex in the yttrium chloride form by using dilute hydrochloric acid. The product from the generator can be used for the preparation of [ 90 Y] - Fe colloid injection or [ 90 Y] - yttrium citrate injection for intra-articular application or for the development of monoclonal antibodies and peptides

Determination of microamounts of potassium in sodium iodide by atomic absorption spectrometry

International Nuclear Information System (INIS)

Ogasawara, Ken; Ohta, Masatoshi; Abe, Kenzo

1980-01-01

Microdetermination of potassium in sodium iodide was developed by the standard addition method. Twenty grams of sample were dissolved in 50 ml of water in a quartz beaker. To the solution, 30 ml of concentrated hydrochloric acid and 30 ml of 30% hydrogen peroxide were added, and evaporated to dryness. By this process sodium iodide was converted into sodium chloride. The cake thus obtained was dissolved in water and diluted to exactly 200 ml. To 25 ml aliquots of the solution, the standard potassium and cesium chloride solutions were added and diluted to 50 ml with water; the concentration of potassium was 0 -- 1 mg/l and that of cesium 4 mM. These solutions were introduced into an air-propane flame and the absorbances were measured at 769.9 nm. During the conversion reaction, hydrochloric acid was completely decomposed, and remained hydrogen peroxide had no influence for absorbance, and other backgrounds were negligible. The linear calibration curve was obtained in the range 0 -- 2 mg of potassium per liter. Potassium in sodium iodide was determined by this method within the coefficient of variation of +-(20 -- 3)% in the range (1.7 -- 32.5) ppm. (author)

The extraction of trace amounts of gold from different aqueous mineral acid solutions by diphenyl-2-pyridylmethane dissolved in chloroform

International Nuclear Information System (INIS)

Iqbal, M.; Ejaz, M.; Chaudhri, S.A.; Zamiruddin

1978-01-01

Diphenyl-2-pyridylmethane, a high-molecular-weight substituted pyridine has been examined. Its behaviour is similar to that of amines in that it forms salts with mineral acids. The acid ionization constant (pKsub(BHsup(+)) is 4.4+-0.06 at 25 deg C. A study of the partition behaviour of trace amounts of gold between mineral acid solutions and 0.1 M diphenyl-2-pyridylmethane dissolved in chloroform indicates that the metal can be quantitatively extracted from dilute mineral acid solutions and also from concentrated hydrochloric acid media in a single extraction. Common anions have little effect on extraction in concentrations up to 1 M. Separation factors of a number of metal ions relative to gold are reported for three mineral acid systems. Gold has been estimated in some synthetic samples using a neutron-activation technique by prior extraction with 0.1 M solution of diphenyl-2-pyridylmethane dissolved in chloroform. Distribution of the test elements between aqueous and organic phase was followed radiometrically. The solutions (usually 1 cm 3 ) were shaken in stoppered vials for 5 minutes using a mechanical shaker. After separation of the layers, 500 μl of each phase were taken for radiochemical analysis. The standard deviation did not exceed 1%. (T.G.)

Regularities of praseodymium oxide dissolution in acids

International Nuclear Information System (INIS)

Savin, V.D.; Elyutin, A.V.; Mikhajlova, N.P.; Eremenko, Z.V.; Opolchenova, N.L.

1989-01-01

The regularities of Pr 2 O 3 , Pr 2 O 5 and Pr(OH) 3 interaction with inorganic acids are studied. pH of the solution and oxidation-reduction potential registrated at 20±1 deg C are the working parameters of studies. It is found that the amount of all oxides dissolved increase in the series of acids - nitric, hydrochloric and sulfuric, in this case for hydrochloric and sulfuric acid it increases in the series of oxides Pr 2 O 3 , Pr 2 O 5 and Pr(OH) 3 . It is noted that Pr 2 O 5 has a high value of oxidation-reduction potential with a positive sign in the whole disslolving range. A low positive value of a redox potential during dissolving belongs to Pr(OH) 3 and in the case of Pr 2 O 3 dissloving redox potential is negative. The schemes of dissolving processes which do not agree with classical assumptions are presented

The removal of uranium from acidic media using ion exchange and/or extraction chromatography

International Nuclear Information System (INIS)

FitzPatrick, J.R.; Schake, B.S.; Murphy, J.; Holmes, K.; West, M.H.

1996-06-01

The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-addition, waste stream polishing is associated with this effort in order to achieve more complete removal of uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps

Characteristics of Lignin Fractions from Dilute Acid Pretreated Switchgrass and Their Effect on Cellobiohydrolase from Trichoderma longibrachiatum

Directory of Open Access Journals (Sweden)

Lan Yao

2018-02-01

Full Text Available To investigate the interactions between acid pretreated switchgrass lignin and cellobiohydrolase (CBH, three different lignin fractions were isolated from dilute acid pretreated switchgrass by (i ethanol extraction, followed by (ii dioxane/H2O extraction, and (iii cellulase treatment, respectively. Structural properties of each lignin fraction were elucidated by GPC, 13C-NMR, and 2D-HSQC NMR analyses. The adsorptions of CBH to the isolated lignin fractions were also studied by Langmuir adsorption isotherms. Ethanol-extractable lignin fraction, mainly composed of syringyl (S and guaiacyl (G units, had the lowest molecular weight, while dioxane/H2O-extracted lignin fraction had the lowest S/G ratio with higher content of p-coumaric acid (pCA unit. The residual lignin fraction after enzymatic treatment had the highest S/G ratio without hydroxyphenyl (H unit. Strong associations were found between lignin properties such as lignin composition and S/G ratio and its non-productive enzyme adsorption factors including the maximum adsorption capacity and binding strength.

Alginate biopolymer as green corrosion inhibitor for copper in 1 M hydrochloric acid: Experimental and theoretical approaches

Science.gov (United States)

Jmiai, A.; El Ibrahimi, B.; Tara, A.; El Issami, S.; Jbara, O.; Bazzi, L.

2018-04-01

The anti-corrosion behavior of sodium alginate (SA) on copper in the 1 M hydrochloric medium was carried out using weight loss and electrochemical measurements. The obtained results show that the inhibition increases with SA concentration and then reaches a maximum of 83% at a concentration of 0.1 mg L-1. The effect of temperature on the reactions of copper corrosion inhibition and analyzing the thermodynamic parameters revealed that the mode of adsorption has a physical nature and obeys the Langmuir isotherm. The surface morphology was performed by scanning electron microscopy coupled with energy dispersive X-ray spectrometry and atomic force microscopy. To better understand the adsorption mechanism, describing the relationship between inhibitory ability and the molecular structure of SA, quantum calculations using density functional theory were performed. Monte Carlo simulation approache was performed to know well of the relationship between the inhibition ability and molecular structure of alginate.

Gluconeogenesis from labeled carbon: estimating isotope dilution

International Nuclear Information System (INIS)

Kelleher, J.K.

1986-01-01

To estimate the rate of gluconeogenesis from steady-state incorporation of labeled 3-carbon precursors into glucose, isotope dilution must be considered so that the rate of labeling of glucose can be quantitatively converted to the rate of gluconeogenesis. An expression for the value of this isotope dilution can be derived using mathematical techniques and a model of the tricarboxylic acid (TCA) cycle. The present investigation employs a more complex model than that used in previous studies. This model includes the following pathways that may affect the correction for isotope dilution: 1) flux of 3-carbon precursor to the oxaloacetate pool via acetyl-CoA and the TCA cycle; 2) flux of 4- or 5-carbon compounds into the TCA cycle; 3) reversible flux between oxaloacetate (OAA) and pyruvate and between OAA and fumarate; 4) incomplete equilibrium between OAA pools; and 5) isotope dilution of 3-carbon tracers between the experimentally measured pool and the precursor for the TCA-cycle OAA pool. Experimental tests are outlined which investigators can use to determine whether these pathways are significant in a specific steady-state system. The study indicated that flux through these five pathways can significantly affect the correction for isotope dilution. To correct for the effects of these pathways an alternative method for calculating isotope dilution is proposed using citrate to relate the specific activities of acetyl-CoA and OAA

Acidic Attack Resistance of Cement Mortar Treated with Alkaline

Directory of Open Access Journals (Sweden)

Nadia Nazhat Sabeeh

2017-12-01

Full Text Available The negative effect of acidic attack on the properties of concrete and cement mortar is a topic of increasing significance in the recent years. Many attempts has occurred to mitigate this negative impact by improving the properties of concrete and increase resistance to acids by using additives. The present study includes treatment of sand by alkaline material and examine the effect of treatment on cement mortar resistance towards hydrochloric and sulfuric acid. Results show that sand treatment by alkaline material significantly enhance mortar ability to resist acids. In terms of loss weight, the maximum weight rate gain was 25.54% for specimens immersed in Hydrochloric acid with water cement ratio 40%. For specimens immersed in HCl, the average gain in compressive strength is (20.15-19.433% for w/c (40-45% respectively. The average gain in modulus of rupture toward the influence of H2SO4 is (18.37–17.99% for w/c (40-45%, respectively.

Isolation and structural characterization of sugarcane bagasse lignin after dilute phosphoric acid plus steam explosion pretreatment and its effect on cellulose hydrolysis

Science.gov (United States)

Jijiao Zeng; Zhaohui Tong; Letian Wang; J.Y. Zhu; Lonnie Ingram

2014-01-01

The structure of lignin after dilute phosphoric acid plus steam explosion pretreatment process of sugarcane bagasse in a pilot scale and the effect of the lignin extracted by ethanol on subsequent cellulose hydrolysis were investigated. The lignin structural changes caused by pretreatment were identified using advanced nondestructive techniques such as gel permeation...

Solubilization of tea seed oil in a food-grade water-dilutable microemulsion.

Directory of Open Access Journals (Sweden)

Lingli Deng

Full Text Available Food-grade microemulsions containing oleic acid, ethanol, Tween 20, and water were formulated as a carrier system for tea seed oil (Camellia oleifera Abel.. The effect of ethanol on the phase behavior of the microemulsion system was clearly reflected in pseudo-ternary diagrams. The solubilization capacity and solubilization efficiency of tea seed oil dispersions were measured along the dilution line at a 70/30 surfactant/oil mass ratio with Tween 20 as the surfactant and oleic acid and ethanol (1:3, w/w as the oil phase. The dispersed phase of the microemulsion (1.5% weight ratio of tea seed oil to the total amount of oil, surfactant, and tea seed oil could be fully diluted with water without phase separation. Differential scanning calorimetry and viscosity measurements indicated that both the carrier and solubilized systems underwent a similar microstructure transition upon dilution. The dispersion phases gradually inverted from the water-in-oil phase ( 45% water along the dilution line.

Direct determination of mercury in cosmetic samples by isotope dilution inductively coupled plasma mass spectrometry after dissolution with formic acid

Energy Technology Data Exchange (ETDEWEB)

Gao, Ying; Shi, Zeming; Zong, Qinxia; Wu, Peng; Su, Jing [Sichuan Provincial Key Laboratory of Nuclear Technology in Geology, College of Nuclear Technology and Automation Engineering, Chengdu University of Technology, Chengdu 610059 (China); Liu, Rui, E-mail: liur.ray@gmail.com [Mineral Resources Chemistry Key Laboratory of Sichuan Higher Education Institutions, College of Materials and Chemistry and Chemical Engineering, Chengdu University of Technology, Chengdu 610059 (China)

2014-02-17

Graphical abstract: -- Highlights: •Simple, sensitive, and accurate method is established for mercury determination in cosmetics. •The sample preparation procedure is highly simplified. •Isotope dilution efficiently eliminates matrix effect. •First report of using formic acid based method in combination with PVG-ID-ICP MS for mercury quantitation in cosmetics. -- Abstract: A new method was proposed for the accurate determination of mercury in cosmetic samples based on isotopic dilution (ID)-photochemical vapor generation (PVG)-inductively coupled plasma mass spectrometry (ICP MS) measurement. Cosmetic samples were directly dissolved in formic acid solution and subsequently subjected to PVG for the reduction of mercury into vapor species following by ICP MS detection. Therefore, the risks of analyte contamination and loss were avoided. Highly enriched {sup 201}Hg isotopic spike is added to cosmetics and the isotope ratios of {sup 201}Hg/{sup 202}Hg were measured for the quantitation of mercury. With ID calibration, the influences originating from sample matrixes for the determination of mercury in cosmetic samples have been efficiently eliminated. The effects of several experimental parameters, such as the concentration of the formic acid, and the flow rates of carrier gas and sample were investigated. The method provided good reproducibility and the detection limits were found to be 0.6 pg mL{sup −1}. Finally, the developed method was successfully applied for the determination of mercury in six cosmetic samples and a spike test was performed to verify the accuracy of the method.

A review on methods of recovery of acid(s) from spent pickle liquor of steel industry.

Science.gov (United States)

Ghare, N Y; Wani, K S; Patil, V S

2013-04-01

Pickling is the process of removal of oxide layer and rust formed on metal surface. It also removes sand and corrosion products from the surface of metal. Acids such as sulfuric acid, hydrochloric acid are used for pickling. Hydrofluoric acid-Nitric acid mixture is used for stainless steel pickling. Pickling solutions are spent when acid concentration in pickling solutions decreases by 75-85%, which also has metal content up to 150-250 g/ dm3. Spent pickling liquor (SPL) should be dumped because the efficiency of pickling decreases with increasing content of dissolved metal in the bath. The SPL content depends on the plant of origin and the pickling method applied there. SPL from steel pickling in hot-dip galvanizing plants contains zinc(II), iron, traces of lead, chromium. and other heavy metals (max. 500 mg/dm3) and hydrochloric acid. Zinc(II) passes tothe spent solution after dissolution of this metal from zinc(II)-covered racks, chains and baskets used for transportation of galvanized elements. Unevenly covered zinc layers are usually removed in another pickling bath. Due to this, zinc(II) concentration increases even up to 110 g/dm3, while iron content may reach or exceed even 80 g/dm3 in the same solution. This review presents an overview on different aspects of generation and treatment of SPL with recourse to recovery of acid for recycling. Different processes are described in this review and higher weightage is given to membrane processes.

Selection of refractory materials for acid tanks at the CSN continuous pickling line

International Nuclear Information System (INIS)

Silva, Sidiney Nascimento; Marques, Oscar Rosa; Bueno, Mauricio Chaves; Longo, Elson; Silva Pinheiro, Adriano da

1997-01-01

Aiming at the revamping of the CSN continuous pickling line 4 acid tanks, a Post Mortem study of the refractory lining was carried out. The collected samples were characterized through techniques such as chemical analysis, mercury porosimetry, X-ray diffraction and scanning electronic microscopy. Trying to reproduce the operational conditions closely, laboratorial simulations were carried out. Such simulations lead to the addition of some alterations on the test method proposed by ABNT. Primarily, the sulfuric acid was substituted by hydrochloric acid (30%), containing iron in solution (130g/l). As result, it was concluded that acid resistant refractories containing a smaller alumina and /or corundum and mullite concentrations, presenting a smaller open porosity and average pore diameter, have a better performance face to corrosion due to hydrochloric acid solution. In addition, abrasion wear resistance tests, according to the ASTM-G65-85 standard were carried out in order to select different materials to the acid tanks cells. (author)

Disruption of sugarcane bagasse lignocellulosic structure by means of dilute sulfuric acid pretreatment with microwave-assisted heating

International Nuclear Information System (INIS)

Chen, Wei-Hsin; Tu, Yi-Jian; Sheen, Herng-Kuang

2011-01-01

Highlights: → Pretreatment of dilute sulfuric acid on bagasse using microwave heating. → An increase in reaction temperature destroyed bagasse significantly. → Pretreated bagasse particles were characterized by fragmentation and swelling. → When the temperature was 190 o C, the fragmentation of particles became pronounced. → The influence of heating time on bagasse structure was not significant. - Abstract: Disruption of lignocellulosic structure of biomass plays a key role in producing bioethanol from lignocelluloses. This study investigated the impact of dilute sulfuric acid pretreatment on bagasse structure using microwave heating. Three reaction temperatures of 130, 160 and 190 o C with two heating times of 5 and 10 min were considered and a number of instruments were employed to analyze the properties of the bagasse particles. On account of microwave irradiation into the solution with dielectric heating, the experiments indicated that an increase in reaction temperature destroyed the lignocellulosic structure of bagasse in a significant way. The pretreated bagasse particles were simultaneously characterized by fragmentation and swelling. When the reaction temperature was as high as 190 o C, the fragmentation of particles became fairly pronounced so that the specific surface area of the pretreated material grew substantially. Meanwhile, almost all hemicellulose was removed from bagasse and the crystalline structure of cellulose disappeared. In contrast, the feature of lignin was remained clearly. However, a comparison between the heating times of 5 and 10 min revealed that the influence of the heating time on the lignocellulosic structure was not significant, indicating that the pretreatment with 5 min was sufficiently long.

Effects of SPORL and dilute acid pretreatment on substrate morphology, cell physical and chemical wall structures, and subsequent enzymatic hydrolysis of lodgepole pine

Science.gov (United States)

Xinping Li; Xiaolin Luo; Kecheng Li; J.Y. Zhu; J. Dennis Fougere; Kimberley Clarke

2012-01-01

The effects of pretreatment by dilute acid and sulfite pretreatment to overcome recalcitrance of lignocellulose (SPORL) on substrate morphology, cell wall physical and chemical structures, along with the subsequent enzymatic hydrolysis of lodgepole pine substrate were investigated. FE-SEM and TEM images of substrate structural morphological changes showed that SPORL...

Adsorption properties and porous structure of sulfuric acid treated bentonites determined - SHORT COMMUNICATION

Directory of Open Access Journals (Sweden)

SNEZANA BREZOVSKA

2005-02-01

Full Text Available In a previous paper adsorption isotherms of benzene vapor on natural bentonite from Ginovci, Macedonia, and forms acid activated with 10 % and 15 % solutions of hydrochloric were interpreted by means of the Dubinin–Radushkevich–Stoeckli and Dubinin–Astakhov equations; the investigation has been continued with bentonites acid activated with 10 % and 15 % solutions of sulfuric acid where X-ray analysis indicates smaller structural changes. Using the above equations, the heterogeneity of the micropores and the energetic heterogeneity of the bentonites were determined from the differential distribution of the micropore volume with respect to the structural parameter of the equations characterizing the microporous structure and to the molar free energy of adsorption. Activated bentonites obtain bigger pores but also a certain quantity of new small pores appear during acid activation with the higher concentration of acid. The micropore volumes, determined from the adsorption of benzene vapor, of bentonites activated with 10 % and 15 % solution of hydrochloric acid (144.60 cm3 kg-1 and 110.06 cm3 kg-1, respectively, decrease in comparison with that of natural bentonite (162.55 cm3 kgv.1 In contrast, the values of the micropore volume for bentonities treated with 10 % and 15 % solutions of sulfuric acids increase (169.19 cm3 kg-1 and 227.74 cm3 kg-1. That is due to the difference in the structural changes occurring during activation with hydrochloric and sulfuric acids. The values of the free energy of adsorption of benzene vapor for natural bentonite are higher than those of the acid acitivated bentonities, what is in accordance with the structural and porosity changes.

Involvement of tyrosine residues, N-terminal amino acids, and beta-alanine in insect cuticular sclerotization.

Science.gov (United States)

Andersen, Svend Olav

2007-09-01

During sclerotization of insect cuticle the acyldopamines, N-acetyldopamine (NADA) and N-beta-alanyldopamine (NBAD), are oxidatively incorporated into the cuticular matrix, thereby hardening and stabilizing the material by forming crosslinks between the proteins in the cuticular matrix and by forming polymers filling the intermolecular spaces in the cuticle. Sclerotized cuticle from the locust, Schistocerca gregaria, and the beetle, Tenebrio molitor, was hydrolyzed in dilute hydrochloric acid, and from the hydrolysates some components presumably degradation products of cuticular crosslinks were isolated. In two of the components, the sidechain of 3,4-dihydroxyacetophenone was linked to the amino groups of glycine and beta-alanine, respectively, and in the third component to the phenolic group of tyrosine. These three compounds, glycino-dihydroxyacetophenone, beta-alanino-dihydroxyacetophenone, and O-tyrosino-dihydroxyacetophenone, as well as the previously reported compound, lysino-dihydroxyacetophenone [Andersen, S.O., Roepstorff, P., 2007. Aspects of cuticular sclerotization in the locust, Schistocerca gregaria, and the beetle, Tenebrio molitor. Insect Biochem. Mol. Biol. 37, 223-234], are suggested to be degradation products of cuticular crosslinks, in which amino acid residues formed linkages to both the alpha- and beta-positions of the sidechain of acyldopamines.

Acid-catalyzed kinetics of indium tin oxide etching

Energy Technology Data Exchange (ETDEWEB)

Choi, Jae-Hyeok; Kim, Seong-Oh; Hilton, Diana L. [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Centre for Biomimetic Sensor Science, Nanyang Technological University, 50 Nanyang Drive, 637553 (Singapore); Cho, Nam-Joon, E-mail: njcho@ntu.edu.sg [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Centre for Biomimetic Sensor Science, Nanyang Technological University, 50 Nanyang Drive, 637553 (Singapore); School of Chemical and Biomedical Engineering, Nanyang Technological University, 62 Nanyang Drive, 637459 (Singapore)

2014-08-28

We report the kinetic characterization of indium tin oxide (ITO) film etching by chemical treatment in acidic and basic electrolytes. It was observed that film etching increased under more acidic conditions, whereas basic conditions led to minimal etching on the time scale of the experiments. Quartz crystal microbalance was employed in order to track the reaction kinetics as a function of the concentration of hydrochloric acid and accordingly solution pH. Contact angle measurements and atomic force microscopy experiments determined that acid treatment increases surface hydrophilicity and porosity. X-ray photoelectron spectroscopy experiments identified that film etching is primarily caused by dissolution of indium species. A kinetic model was developed to explain the acid-catalyzed dissolution of ITO surfaces, and showed a logarithmic relationship between the rate of dissolution and the concentration of undisassociated hydrochloric acid molecules. Taken together, the findings presented in this work verify the acid-catalyzed kinetics of ITO film dissolution by chemical treatment, and support that the corresponding chemical reactions should be accounted for in ITO film processing applications. - Highlights: • Acidic conditions promoted indium tin oxide (ITO) film etching via dissolution. • Logarithm of the dissolution rate depended linearly on the solution pH. • Acid treatment increased ITO surface hydrophilicity and porosity. • ITO film etching led to preferential dissolution of indium species over tin species.

Effect of surface acidic oxides of activated carbon on adsorption of ammonia.

Science.gov (United States)

Huang, Chen-Chia; Li, Hong-Song; Chen, Chien-Hung

2008-11-30

The influence of surface acidity of activated carbon (AC) was experimentally studied on adsorption of ammonia (NH(3)). Coconut shell-based AC was modified by various acids at different concentrations. There were five different acids employed to modified AC, which included nitric acid, sulfuric acid, hydrochloric acid, phosphoric acid, and acetic acid. Acidic functional groups on the surface of ACs were determined by a Fourier transform infrared spectrograph (FTIR) and by the Boehm titration method. Specific surface area and pore volume of the ACs were measured by a nitrogen adsorption apparatus. Adsorption amounts of NH(3) onto the ACs were measured by a dynamic adsorption system at room temperature according to the principle of the ASTM standard test method. The concentration of NH(3) in the effluent stream was monitored by a gas-detecting tube technique. Experimental results showed that adsorption amounts of NH(3) on the modified ACs were all enhanced. The ammonia adsorption amounts on various activated carbons modified by different acids are in the following order: nitric acid>sulfuric acid>acetic acid approximately phosphoric acid>hydrochloric acid. It is worth to note that the breakthrough capacity of NH(3) is linearly proportional to the amount of acidic functional groups of the ACs.

High School Forum: "Invitations to Enquiry": The Calcite/Acid Reaction.

Science.gov (United States)

Herron, J. Dudley, Ed.; Driscoll, D. R.

1979-01-01

Describes a high school chemistry experiment which involves the reaction between calcite and hydrochloric and sulfuric acids. This reaction can be carried out as a projected demonstration and on an individual basis. (HM)

An evaluation of dilute acid and ammonia fiber explosion pretreatment for cellulosic ethanol production.

Science.gov (United States)

Mathew, Anil Kuruvilla; Parameshwaran, Binod; Sukumaran, Rajeev Kumar; Pandey, Ashok

2016-01-01

The challenge associated with cellulosic ethanol production is maximizing sugar yield at low cost. Current research is being focused to develop a pretreatment method to overcome biomass recalcitrance in an efficient way. This review is focused on two major pretreatments: dilute acid (DA) and ammonia fiber explosion (AFEX) pretreatment of corn stover and how these pretreatment cause morphological and chemical changes to corn stover in order to overcome the biomass recalcitrance. This review highlights the key differences of these two pretreatments based on compositional analysis, cellulose and its crystallinity, morphological changes, structural changes to lignin, enzymatic reactivity and enzyme adsorption onto pretreated solids and finally cellulosic ethanol production from the hydrolysate of DA and AFEX treated corn stover. Each stage of the process, AFEX pretreated corn stover was superior to DA treated corn stover. Copyright © 2015 Elsevier Ltd. All rights reserved.

Methods of increasing the harshness of texture of old concrete pavements--acid etching.

Science.gov (United States)

1975-01-01

Of the four acids tested in the laboratory, the nitric and hydrochloric types were selected for field experiments. These two acids performed about equally well, the choice as to which to use is dictated by price and availability. In the field experim...

Stable isotope dilution HILIC-MS/MS method for accurate quantification of glutamic acid, glutamine, pyroglutamic acid, GABA and theanine in mouse brain tissues.

Science.gov (United States)

Inoue, Koichi; Miyazaki, Yasuto; Unno, Keiko; Min, Jun Zhe; Todoroki, Kenichiro; Toyo'oka, Toshimasa

2016-01-01

In this study, we developed the stable isotope dilution hydrophilic interaction liquid chromatography with tandem mass spectrometry (HILIC-MS/MS) technique for the accurate, reasonable and simultaneous quantification of glutamic acid (Glu), glutamine (Gln), pyroglutamic acid (pGlu), γ-aminobutyric acid (GABA) and theanine in mouse brain tissues. The quantification of these analytes was accomplished using stable isotope internal standards and the HILIC separating mode to fully correct the intramolecular cyclization during the electrospray ionization. It was shown that linear calibrations were available with high coefficients of correlation (r(2)  > 0.999, range from 10 pmol/mL to 50 mol/mL). For application of the theanine intake, the determination of Glu, Gln, pGlu, GABA and theanine in the hippocampus and central cortex tissues was performed based on our developed method. In the region of the hippocampus, the concentration levels of Glu and pGlu were significantly reduced during reality-based theanine intake. Conversely, the concentration level of GABA increased. This result showed that transited theanine has an effect on the metabolic balance of Glu analogs in the hippocampus. Copyright © 2015 John Wiley & Sons, Ltd.

Evaluation of the physico-chemical properties of acid thinned ...

African Journals Online (AJOL)

From the investigation, the acid modification of cassava starch at 60°C with 0.1M hydrochloric acid solutions for 1hr and 2hr gave pastes that are stable, and have workable viscosities and can form gel in food processing. Therefore, the results suggest that they are suitable for the food industry as food emulsifiers/stabilizers.

Inhibition Effect of Deanol on Mild Steel Corrosion in Dilute ...

African Journals Online (AJOL)

NICOLAAS

2014-06-23

Jun 23, 2014 ... The influence of deanol on the corrosion behaviour of mild steel in dilute sulphuric acid with sodium ... the formation of a complex precipitate of protective film, which ... silicon carbide abrasive papers of 80, 120, 220, 800 and 1000 grit ...... ions in sulphuric acid on the corrosion behaviour of stainless steel,.

Bioethanol productions from rice polish by optimization of dilute acid ...

African Journals Online (AJOL)

Lignocellulose materials are abundant renewable resource for the production of biofuel from fermentative organism (Sacchromyces cervesiae). Rice polish is cheapest and abundant lignocelluloses resource and has potential to produce bioethanol. The main steps for the conversion of biomass into glucose required dilute ...

Study of radium extraction mechanisms from scales by leaching in different acidic and alkaline media

International Nuclear Information System (INIS)

Al-Masri, M. S.; Gafar, M.; Al-Kurdi, H.

2002-07-01

The present report shows the results of leaching experiments for scales containing naturally occuring radioactive materials using different acidic and alkaline media. The obtained result can be used for defining the method of safe disposal of such waste. Leaching solutions used in this study were distilled water, mineral acids (sulpharic acid, hydrochloric acid and nitric acid), sodium, potassium hydroxides, ammonium oxalate EDTA, sodium carbonate, potassium acetate, and a mixture of potassium chloride and hydrochloric acid. The results have shown that the extraction ratio of radium-226, the most abundant isotope in scales, is very low and even negligible using all different media. This indicates that all scales produced in Syrian oil fields do not require any chemical preparation before disposal. In addition, the effect of both stirring time of phrases and concentration of leaching media that may affect the radium transfer process from solid phase to aqueous phase have been investigated were no measurable amount being observed in the leachate. (author)

Soil washing of chromium- and cadmium-contaminated sludge using acids and ethylenediaminetetra acetic acid chelating agent.

Science.gov (United States)

Gitipour, Saeid; Ahmadi, Soheil; Madadian, Edris; Ardestani, Mojtaba

2016-01-01

In this research, the effect of soil washing in the removal of chromium- and cadmium-contaminated sludge samples collected from Pond 2 of the Tehran Oil Refinery was investigated. These metals are considered as hazardous substances for human health and the environment. The carcinogenicity of chromate dust has been established for a long time. Cadmium is also a potential environmental toxicant. This study was carried out by collecting sludge samples from different locations in Pond 2. Soil washing was conducted to treat the samples. Chemical agents, such as acetic acid, ethylenediaminetetra acetic acid (EDTA) and hydrochloric acid, were used as washing solutions to remove chromium and cadmium from sludge samples. The results of this study indicated that the highest removal efficiencies from the sludge samples were achieved using a 0.3 M HCl solution with 82.69% and 74.47% for chromium and cadmium, respectively. EDTA (0.1 M) in the best condition extracted 66.81% of cadmium and 72.52% of chromium from the sludges. The lowest efficiency values for the samples, however, were achieved using 3 M acetic acid with 41.7% and 46.96% removals for cadmium and chromium, respectively. The analysis of washed sludge indicated that the heavy metals removal decreased in the order of 3 M acetic acid < 0.1 M EDTA<0.3 M HCl, thus hydrochloric acid appears to offer a greater potential as a washing agent in remediating the sludge samples.

The effect of pH on the erosion of dentine and enamel by dietary acids in vitro.

Science.gov (United States)

West, N X; Hughes, J A; Addy, M

2001-09-01

The reported incidence of tooth erosion caused by acidic soft drinks has been increasingly documented. Citric and phosphoric acids are the two main dietary acids present in these soft drinks. Many variables need to be determined in order to assess risk factors for dental erosion caused by beverage consumption including pH, titratable acidity, pKa, buffering capacity, hence the aim of these in vitro investigations. Methodologies included profiling flat enamel and dentine samples (acidic solutions adjusted with alkali over the available pH range; citric, phosphoric and hydrochloric acid were adjusted with sodium hydroxide and citric acid with trisodium citrate. Tissue loss was calculated by profilometry. Results showed that under these conditions citric acid caused far more erosion over the pH range employed than phosphoric acid for both tissue types. Citric acid compared with hydrochloric acid highlighted dissolution and chelation effects. Phosphoric acid caused minimal erosion over pH 3 for enamel and pH 4 for dentine. These factors could be considered in order to reduce the erosivity of acidic soft drinks.

Introducing AAA-MS, a rapid and sensitive method for amino acid analysis using isotope dilution and high-resolution mass spectrometry.

Science.gov (United States)

Louwagie, Mathilde; Kieffer-Jaquinod, Sylvie; Dupierris, Véronique; Couté, Yohann; Bruley, Christophe; Garin, Jérôme; Dupuis, Alain; Jaquinod, Michel; Brun, Virginie

2012-07-06

Accurate quantification of pure peptides and proteins is essential for biotechnology, clinical chemistry, proteomics, and systems biology. The reference method to quantify peptides and proteins is amino acid analysis (AAA). This consists of an acidic hydrolysis followed by chromatographic separation and spectrophotometric detection of amino acids. Although widely used, this method displays some limitations, in particular the need for large amounts of starting material. Driven by the need to quantify isotope-dilution standards used for absolute quantitative proteomics, particularly stable isotope-labeled (SIL) peptides and PSAQ proteins, we developed a new AAA assay (AAA-MS). This method requires neither derivatization nor chromatographic separation of amino acids. It is based on rapid microwave-assisted acidic hydrolysis followed by high-resolution mass spectrometry analysis of amino acids. Quantification is performed by comparing MS signals from labeled amino acids (SIL peptide- and PSAQ-derived) with those of unlabeled amino acids originating from co-hydrolyzed NIST standard reference materials. For both SIL peptides and PSAQ standards, AAA-MS quantification results were consistent with classical AAA measurements. Compared to AAA assay, AAA-MS was much faster and was 100-fold more sensitive for peptide and protein quantification. Finally, thanks to the development of a labeled protein standard, we also extended AAA-MS analysis to the quantification of unlabeled proteins.

Comparison of extraction fluids used with contaminated soils

International Nuclear Information System (INIS)

Erickson, D.C.; White, E.; Loehr, R.C.

1991-01-01

Five separate solutions were evaluated for use as leaching fluids with soils containing petroleum refining waste residues. The extraction fluids were: (a) water, (b) dilute hydrochloric acid, (c) 0.05 molar EDTA, (d) acetate buffer and (e) a dilute sulfuric/nitric acid mixture. The soils were collected from former refinery land treatment sites which had been used to treat petroleum refining wastes. The extractions were performed using a rotary tumbler (30 RPM, 18 hours) and the resulting solutions were analyzed for polynuclear aromatic hydrocarbons (PAHs) and metals. Concentrations of the PAHs in each of the five solutions were near or below the analytical quantitation limits. Metal concentrations were highest in the HCL and EDTA extracts, although only a small fraction of the total available metal present in the soils was extracted by the solutions evaluated

Utilizing ultrasonic energy for reduction of free fatty acids in crude ...

African Journals Online (AJOL)

Ultrasonic energy was used for the reduction of FFA in CPO. FFA content was measured at different sonication intervals, and the optimum time was determined. Hydrochloric acid showed the highest catalytic activity in the reduction of FFA content in CPO, as well as in converting FFA to fatty acid methyl ester (FAME).

Kinetic and Modeling Investigation to Provide Design Guidelines for the NREL Dilute-Acid Process Aimed at Total Hydrolysis/Fractionation of Lignocellulosic Biomass: July 1998

Energy Technology Data Exchange (ETDEWEB)

Lee, Y. Y.; Iyer, P.; Xiang, Q.; Hayes, J.

2004-08-01

Following up on previous work, subcontractor investigated three aspects of using NREL ''pretreatment'' technology for total hydrolysis (cellulose as well as hemicellulose) of biomass. Whereas historic hydrolysis of biomass used either dilute acid or concentrated acid technology for hydrolysis of both hemicellulose and cellulose, NREL has been pursuing very dilute acid hydrolysis of hemicellulose followed by enzymatic hydrolysis of cellulose. NREL's countercurrent shrinking-bed reactor design for hemicellulose hydrolysis (pretreatment) has, however, shown promise for total hydrolysis. For the first task, subcontractor developed a mathematical model of the countercurrent shrinking bed reactor operation and, using yellow poplar sawdust as a feedstock, analyzed the effect of: initial solid feeding rate, temperature, acid concentration, acid flow rate, Peclet number (a measure of backmixing in liquid flow), and bed shrinking. For the second task, subcontractor used laboratory trials, with yellow poplar sawdust and 0.07 wt% sulfuric acid at various temperatures, to verify the hydrolysis of cellulose to glucose (desired) and decomposition of glucose (undesired) and determine appropriate parameters for use in kinetic models. Unlike cellulose and hemicellulose, lignins, the third major component of biomass, are not carbohydrates that can be broken down into component sugars. They are, however, aromatic complex amorphous phenolic polymers that can likely be converted into low-molecular weight compounds suitable for production of fuels and chemicals. Oxidative degradation is one pathway for such conversion and hydrogen peroxide would be an attractive reagent for this, as it would leave no residuals. For the third task, subcontractor reacted lignin with hydrogen peroxide under various conditions and analyzed the resulting product mix.

Degradation of chitosan hydrogel dispersed in dilute carboxylic acids by solution plasma and evaluation of anticancer activity of degraded products

Science.gov (United States)

Chokradjaroen, Chayanaphat; Rujiravanit, Ratana; Theeramunkong, Sewan; Saito, Nagahiro

2018-01-01

Chitosan is a polysaccharide that has been extensively studied in the field of biomedicine, especially its water-soluble degraded products called chitooligosaccharides (COS). In this study, COS were produced by the degradation of chitosan hydrogel dispersed in a dilute solution (i.e., 1.55 mM) of various kinds of carboxylic acids using a non-thermal plasma technology called solution plasma (SP). The degradation rates of chitosan were influenced by the type of carboxylic acids, depending on the interaction between chitosan and each carboxylic acid. After SP treatment, the water-soluble degraded products containing COS could be easily separated from the water-insoluble residue of chitosan hydrogel by centrifugation. The production yields of the COS were mostly higher than 55%. Furthermore, the obtained COS products were evaluated for their inhibitory effect as well as their selectivity against human lung cancer cells (H460) and human lung normal cells (MRC-5).

Ex Vivo Liver Experiment of Hydrochloric Acid-Infused and Saline-Infused Monopolar Radiofrequency Ablation: Better Outcomes in Temperature, Energy, and Coagulation

Energy Technology Data Exchange (ETDEWEB)

Jiang, Xiong-ying; Gu, Yang-kui; Huang, Jin-hua, E-mail: huangjh@sysucc.org.cn; Gao, Fei; Zou, Ru-hai; Zhang, Tian-qi [Collaborative Innovation Center for Cancer Medicine, Sun Yat-sen University Cancer Center, State Key Laboratory of Oncology in South China (China)

2016-04-15

ObjectiveTo compare temperature, energy, and coagulation between hydrochloric acid-infused radiofrequency ablation (HAIRFA) and normal saline-infused radiofrequency ablation (NSIRFA) in ex vivo porcine liver model.Materials and Methods30 fresh porcine livers were excised in 60 lesions, 30 with HAIRFA and the other 30 with NSIRFA. Both modalities used monopolar perfusion electrode connected to a RF generator set at 103 °C and 30 W. In each group, ablation time was set at 10, 20, or 30 min (10 lesions from each group at each time). We compared tissue temperatures (at 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 cm away from the electrode tip), average power, deposited energy, deposited energy per coagulation volume (DEV), coagulation diameters, coagulative volume, and spherical ratio between the two groups.ResultsTemperature–time curves showed that HAIRFA provided progressively greater heating than that of NSIRFA. At 30 min, mean average power, deposited energy, coagulation volumes (113.67 vs. 12.28 cm{sup 3}) and diameters, and increasing in tissue temperature were much greater with HAIRFA (P < 0.001 for all), except DEV was lower (456 vs. 1396 J/cm{sup 3}, P < 0.001). The spherical ratio was closer to 1 with HAIRFA (1.23 vs. 1.46). Coagulation diameters, volume, and average power of HAIRFA increased significantly with longer ablation times. While with NSIRFA, these characteristics were stable till later 20 min, except the power decreased with longer ablation times.ConclusionsHAIRFA creates much larger and more spherical lesions by increasing overall energy deposition, modulating thermal conductivity, and transferring heat during ablation.

Spectroscopic analysis of hot-water- and dilute-acid-extracted hardwood and softwood chips

Science.gov (United States)

Lehto, Joni; Louhelainen, Jarmo; Huttunen, Marko; Alén, Raimo

2017-09-01

Hot-water and dilute sulfuric acid pretreatments were performed prior to chemical pulping for silver/white birch (Betula pendula/B. pubescens) and Scots pine (Pinus sylvestris) chips to determine if varying pretreatment conditions on the original wood material were detectable via attenuated total reflectance (ATR) infrared spectroscopy. Pretreatment conditions varied with respect to temperature (130 °C and 150 °C) and treatment time (from 30 min to 120 min). The effects of the pretreatments on the composition of wood chips were determined by ATR infrared spectroscopy. The spectral data were compared to those determined by common wood chemistry analyses to evaluate the suitability of ATR spectroscopy method for rapid detection of changes in the wood chemical composition caused by different pretreatment conditions. In addition to determining wood species-dependent differences in the wood chemical composition, analytical results indicated that most essential lignin- and carbohydrates-related phenomena taking place during hot-water and acidic pretreatments could be described by applying this simple spectral method requiring only a small sample amount and sample preparation. Such information included, for example, the cleavage of essential lignin bonds (i.e., mainly β-O-4 linkages in guaiacyl and syringyl lignin) and formation of newly condensed lignin structures under different pretreatment conditions. Carbohydrate analyses indicated significant removal of hemicelluloses (especially hardwood xylan) and hemicelluloses-derived acetyl groups during the pretreatments, but they also confirmed the highly resistant nature of cellulose towards mild pretreatments.

Diglycolic acid modified zirconium phosphate and studies on the extraction of Am(III) and Eu(III) from dilute nitric acid medium

Energy Technology Data Exchange (ETDEWEB)

Selvan, B. Robert; Suneesh, A.S.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Division; Dasthaiah, K.; Gardas, R.L. [Indian Institute of Technology - Madras, Chennai (India). Dept. of Chemistry

2017-06-01

Diglycolic acid modified zirconium phosphate (ZrP-DGA) was prepared and studied for the extraction of Am(III) and Eu(III) from dilute nitric acid medium. The distribution coefficient (K{sub d}, mL.g{sup -1}) of Am(III) and Eu(III) was measured as a function of time, pH and concentration of Eu(III) ion etc. The K{sub d} of Am(III) and Eu(III) increased with increase of pH, reached a maximum value of distribution coefficient at pH 1.5 - 2, followed by decrease in K{sub d} values. Rapid extraction of Am(III) and Eu(III) in ZrP-DGA was observed followed by the establishment of equilibrium occurred in 100 min. Kinetics of extraction was fitted in to pseudo second order rate equation. The amount of Eu(III) loaded in ZrP-DGA increased with increase in the concentration of Eu(III) ion in aqueous phase and the isotherm was fitted in to Langmuir and Freundlich adsorption models. The extraction of Am(III) in ZrP-DGA was higher as compared to Eu(III) and the interference of Eu(III) on the extraction of Am(III) was studied. The distribution coefficient of some lanthanides in ZrP-DGA was measured and the K{sub d} of lanthanides increased across the lanthanide series. The extracted trivalent metal ions were recovered in three contacts of loaded ZrP-DGA with 0.5 M nitric acid.

Quantitation of 5-Methyltetrahydrofolic Acid in Dried Blood Spots and Dried Plasma Spots by Stable Isotope Dilution Assays.

Directory of Open Access Journals (Sweden)

Markus Kopp

Full Text Available Because of minimal data available on folate analysis in dried matrix spots (DMSs, we combined the advantages of stable isotope dilution assays followed by LC-MS/MS analysis with DMS sampling to develop a reliable method for the quantitation of plasma 5-methyltetrahydrofolic acid in dried blood spots (DBSs and dried plasma spots (DPSs as well as for the quantitation of whole blood 5-methyltetrahydrofolic acid in DBSs. We focused on two diagnostically conclusive parameters exhibited by the plasma and whole blood 5-methyltetrahydrofolic acid levels that reflect both temporary and long-term folate status. The method is performed using the [2H4]-labeled isotopologue of the vitamin as the internal standard, and three steps are required for the extraction procedure. Elution of the punched out matrix spots was performed using stabilization buffer including Triton X-100 in a standardized ultrasonication treatment followed by enzymatic digestion (whole blood only and solid-phase extraction with SAX cartridges. This method is sensitive enough to quantify 27 nmol/L whole blood 5-methyltetrahydrofolic acid in DBSs and 6.3 and 4.4 nmol/L plasma 5-methyltetrahydrofolic acid in DBSs and DPSs, respectively. The unprecedented accurate quantification of plasma 5-methyltetrahydrofolic acid in DBSs was achieved by thermal treatment prior to ultrasonication, inhibiting plasma conjugase activity. Mass screenings are more feasible and easier to facilitate for this method in terms of sample collection and storage compared with conventional clinical sampling for the assessment of folate status.

Rapid and precise measurement of serum branched-chain and aromatic amino acids by isotope dilution liquid chromatography tandem mass spectrometry.

Directory of Open Access Journals (Sweden)

Ruiyue Yang

Full Text Available BACKGROUND: Serum branched-chain and aromatic amino acids (BCAAs and AAAs have emerged as predictors for the future development of diabetes and may aid in diabetes risk assessment. However, the current methods for the analysis of such amino acids in biological samples are time consuming. METHODS: An isotope dilution liquid chromatography tandem mass spectrometry (ID-LC/MS/MS method for serum BCAAs and AAAs was developed. The serum was mixed with isotope-labeled BCAA and AAA internal standards and the amino acids were extracted with acetonitrile, followed by analysis using LC/MS/MS. The LC separation was performed on a reversed-phase C18 column, and the MS/MS detection was performed via the positive electronic spray ionization in multiple reaction monitoring mode. RESULTS: Specific analysis of the amino acids was achieved within 2 min. Intra-run and total CVs for the amino acids were less than 2% and 4%, respectively, and the analytical recoveries ranged from 99.6 to 103.6%. CONCLUSION: A rapid and precise method for the measurement of serum BCAAs and AAAs was developed and may serve as a quick tool for screening serum BCAAs and AAAs in studies assessing diabetes risk.

Microtensile strength of spruce pine after exposure to acids and bases

Science.gov (United States)

Floyd G. Manwiller; Paul R. Godfrey

1972-01-01

Earlywood and latewood microtensile specimens from 12 trees of Pinus glabra Wal. were subjected to 10-percent solution of 5 acids and 3 bases at 90oC for up to 3 hours. Hydrochloric and sulfuric acids were the most damaging, lowering maximum tensile strength 27 and 17 percent in earlywood and 36 and 39 percent in latewood; they...

Lower pressure heating steam is practical for the distributed dry dilute sulfuric acid pretreatment.

Science.gov (United States)

Shao, Shuai; Zhang, Jian; Hou, Weiliang; Qureshi, Abdul Sattar; Bao, Jie

2017-08-01

Most studies paid more attention to the pretreatment temperature and the resulted pretreatment efficiency, while ignored the heating media and their scalability to an industry scale. This study aimed to use a relative low pressure heating steam easily provided by steam boiler to meet the requirement of distributed dry dilute acid pretreatment. The results showed that the physical properties of the pretreated corn stover were maintained stable using the steam pressure varying from 1.5, 1.7, 1.9 to 2.1MPa. Enzymatic hydrolysis and high solids loading simultaneous saccharification and fermentation (SSF) results were also satisfying. CFD simulation indicated that the high injection velocity of the low pressure steam resulted in a high steam holdup and made the mixing time of steam and solid corn stover during pretreatment much shorter in comparison with the higher pressure steam. This study provides a design basis for the boiler requirement in distributed pretreatment concept. Copyright © 2017 Elsevier Ltd. All rights reserved.

Acid hydrolysis of kallar grass (leptochloa fusca) for the production

International Nuclear Information System (INIS)

Chughtai, F.A.; Shah, M.H.

1993-01-01

Acid hydrolysis of kallar grass (leptochloa fusca) was carried of with various concentrations of sulphuric acid, ortho phosphoric acid and hydrochloric acid to produce furfural. The study revealed that activity of various hydrolysing acids to produce furfural from kallar grass was of the following order H/sub 2/SO/sub 4/ > H/sub 3/PO/sub 4/ > HCl. Optimum yield (4.78%) of the produce was obtained when the material was digested with 19% H/sub 2/SO/sub 4/ for a period of 20 minutes. (author)

Magnesium hydroxide as the neutralizing agent for radioactive hydrochloric acid solutions

International Nuclear Information System (INIS)

Palmer, M.J.; Fife, K.W.

1995-10-01

The current technology at Los Alamos for removing actinides from acidic chloride waste streams is precipitation with approximately 10 M potassium hydroxide. Although successful, there are many inherent drawbacks to this precipitation technique which will be detailed in this paper. Magnesium hydroxide (K sp = 1.3 x 10 -11 ) has limited solubility in water and as a result of the common ion effect, cannot generate a filtrate with a pH greater than 9. At a pH of 9, calcium (K sp = 5.5 x 10 -6 ) will not coprecipitate as the hydroxide. This is an important factor since many acidic chloride feeds to hydroxide precipitation contain significant amounts of calcium. In addition, neutralization with Mg(OH) 2 produces a more filterable precipitate because neutralization occurs as the Mg(OH) 2 is dissolved by the acid rather than as a result of the much faster liquid/liquid reaction of KOH with the waste acid. This slower solid/liquid reaction allows time for crystal growth to occur and produces more easily filterable precipitates. On the other hand, neutralization of spent acid with strong KOH that yields numerous hydroxide ions in solution almost instantaneously forming a much larger volume of small crystallites that result in gelatinous, slow-filtering precipitates. Magnesium hydroxide also offers a safety advantage. Although mildly irritating, it is a weak base and safe and easy to handle. From a waste minimization perspective, Mg(OH) 2 offers many advantages. First, the magnesium hydroxide is added as a solid. This step eliminates the diluent water used in KOH neutralizations. Secondly, because the particle size of the precipitate is larger, more actinides are caught on the filter paper resulting in a smaller amount of actinide being transferred to the TA-50 Liquid Waste Treatment Facility. Third, the amount of solids that must be reprocessed is significantly smaller resulting in less waste generation from the downstream processes

Photo-oxidation of gaseous ethanol on photocatalyst prepared by acid leaching of titanium oxide/hydroxyapatite composite

International Nuclear Information System (INIS)

Ono, Y.; Rachi, T.; Yokouchi, M.; Kamimoto, Y.; Nakajima, A.; Okada, K.

2013-01-01

Highlights: ► Photocatalyst powder was prepared by acid leaching of TiO 2 /apatite composite. ► The photocatalytic activity was evaluated from in situ FT-IR study using ethanol. ► Apatite in the composite had positive effect for the photo-oxidation of ethanol. ► The enhanced oxidation rate was explained by the difference in deactivation rate. - Abstract: Highly active photocatalysts were synthesized by leaching of heat-treated titanium dioxide (TiO 2 )/hydroxyapatite (HAp) powder with hydrochloric acid at 0.25, 0.50, 0.75 mol/l, and their photocatalytic activities were evaluated from in situ Fourier transform infrared (FT-IR) study of photo-oxidation of gaseous ethanol. By changing the acid concentration, the TiO 2 /HAp composite had different atomic ratios of Ca/Ti (0.0–2.8) and P/Ti (0.3–2.1). It was found that phosphate group remained on the surface of TiO 2 particle even in the sample treated with concentrated acid (0.75 mol/l). These acid-treated samples showed higher rates for ethanol photo-oxidation than the commercial TiO 2 powder, Degussa P25. The highest rate was obtained in the TiO 2 /HAp composite treated with the dilute (0.25 mol/l) acid in spite of its low content of TiO 2 photocatalyst. This enhanced photocatalytic activity was attributed to the result that the deactivation with repeated injections of ethanol gas was suppressed in the TiO 2 /HAp composites compared with the TiO 2 powders

Synthesis of tungsten oxide nanoparticles using a hydrothermal method at ambient pressure

DEFF Research Database (Denmark)

Ahmadi, Majid; Younesi, Reza; Guinel, Maxime J-F

2014-01-01

) nanoparticles were synthesized using a simple and inexpensive low temperature and low pressure hydrothermal (HT) method. The precursor solution used for the HT process was prepared by adding hydrochloric acid to diluted sodium tungstate solutions (Na2WO4 center dot 2H(2)O) at temperatures below 5 degrees C...... and then dissolved using oxalic acid. This HT process yielded tungstite (WO3 center dot H2O) nanoparticles with the orthorhombic structure. A heat treatment at temperatures at or above 300 degrees C resulted in a phase transformation to monoclinic WO3, while preserving the nanoparticles morphology. The production...

Method of decontaminating radioactive-contaminated instruments

Energy Technology Data Exchange (ETDEWEB)

Urata, M; Fujii, M; Kitaguchi, H

1982-03-29

Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode.

Comparison of isotope dilution and excretion methods for determining the half-life of ascorbic acid in the guinea pig

International Nuclear Information System (INIS)

Kipp, D.E.; Rivers, J.M.

1984-01-01

The half-life of ascorbic acid (AA) in guinea pigs was investigated by the isotope dilution and excretion methods. The dilution method measures [1-14C]AA disappearance from the plasma, whereas the excretion method measures the elimination of [1-14C]AA and the metabolites from the body. Two groups of animals underwent both isotope studies in reverse order. Animals were conditioned to the experimental procedures and fed 2.5 mg AA/100 g body weight orally to maintain a daily intake of the vitamin independent of food consumption. The two isotope procedures imposed similar stress on the animals, as determined by plasma cortisol levels and body weight changes. The AA half-life calculations of the rapidly exchangeable pool by the isotope dilution method yielded values of 1.23 and 0.34 hours for the two groups, respectively. The half-life of the slowly exchangeable pool for the two groups was 60.2 and 65.8 hours, respectively. The half-life of AA in the rapidly exchangeable pool, as measured by the excretion studies, was 4.57-8.75 hours. For the slowly exchangeable pool, it was 146-149 hours. The longer half-life of both pools obtained with the excretion method indicates that the isotope is disappearing from the plasma more rapidly than it is being excreted. This suggests that a portion of the [1-14C]AA leaving the plasma is removed to a body pool that is not sampled by the isotope excretion method

Lauric Acid Hybridizing Fly Ash Composite for Thermal Energy Storage

Directory of Open Access Journals (Sweden)

Dawei Xu

2018-04-01

Full Text Available Fly ash includes different mineral phases. This paper reported on the preparation of a novel lauric acid (LA/fly ash (FA composite by vacuum impregnation as a form-stable phase change material (PCM for thermal energy, and especially investigated the effect of the hydrochloric acid-treated fly ash (FAh on the thermal energy storage performance of the composites. The morphology, crystalline structure, and porous textures of the samples were characterized by scanning electron microscopy (SEM, X-ray diffraction (XRD, Brunauer–Emmett–Teller (BET, X-ray fluorescence (XRF, and differential scanning calorimetry (DSC. The results indicated that hydrochloric acid treatment was beneficial to the increase of loading capacity and crystallinity of LA in the LA/FAh composite, which caused an enhanced thermal storage capacity with latent heats for melting and freezing of LA/FAh (80.94 and 77.39 J/g, higher than those of LA/FA (34.09 and 32.97 J/g, respectively. Furthermore, the mechanism of enhanced thermal storage properties was investigated in detail.

Process Design and Economics for the Conversion of Lignocellulosic Biomass to Hydrocarbons: Dilute-Acid and Enzymatic Deconstruction of Biomass to Sugars and Biological Conversion of Sugars to Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Davis, R.; Tao, L.; Tan, E. C. D.; Biddy, M. J.; Beckham, G. T.; Scarlata, C.; Jacobson, J.; Cafferty, K.; Ross, J.; Lukas, J.; Knorr, D.; Schoen, P.

2013-10-01

This report describes one potential conversion process to hydrocarbon products by way of biological conversion of lingnocellulosic-dervied sugars. The process design converts biomass to a hydrocarbon intermediate, a free fatty acid, using dilute-acid pretreatement, enzymatic saccharification, and bioconversion. Ancillary areas--feed handling, hydrolysate conditioning, product recovery and upgrading (hydrotreating) to a final blendstock material, wastewater treatment, lignin combusion, and utilities--are also included in the design.

Effects of chopping, and soaking in water, hydrochloric acidic and calcium hydroxide solutions on the nutritional value of Acacia villosa for goats

International Nuclear Information System (INIS)

Wina, E.; Tangendjaja, B.; Susana, I.W.R.

2005-01-01

Acacia villosa, a thornless shrub legume, has potential as a feed supplement for ruminants if anti-nutritional factors, especially tannins, can be overcome. The effects of chopping and soaking the leaves on the amounts of tannin in the extracting solution and that left in the recovered leaves were studied. The tannin and non-tannin phenolics were solubilized in the extracting solution and the amount was increased with the soaking time. Soaking in calcium hydroxide solution, hydrochloric acid or water removed 41-76% of tannin and total phenolics removed from the recovered leaves. Soaking of the leaves also removed fermentable materials and reduced the gas production. In the first of two digestibility experiments, three groups of goats received one of these diets, those were: (1) sugar cane tops: unsoaked Acacia leaves (7:3), (2) sugar cane tops: water soaked Acacia leaves (7:3) and (3) sugar cane tops: water soaked Acacia leaves (7:3) + 100 g/day of cassava flour. Live weight of goats was measured every 2 weeks and a large increase in average daily gain was obtained for goats fed diet containing water soaked leaves and cassava flour (71 g/day) compared to those fed diet containing unsoaked leaves and water soaked leaves (38.9 and 44.7 g/day, respectively) (P 0.05) found in intake or digestibility between unsoaked and soaked leaves. In conclusion, soaking reduced tannin in Acacia leaves, improved digestibility and intake of Acacia leaves. In the presence of cassava flour, soaking improved average daily gain. Diets supplemented with water soaked Acacia leaves probably also need an energy supplement and cassava flour is one of the feed ingredients that is satisfactory. (author)

Effect of low severity dilute-acid pretreatment of barley straw and decreased enzyme loading hydrolysis on the production of fermentable substrates and the release of inhibitory compounds

NARCIS (Netherlands)

Panagiotopoulos, I.A.; Lignos, G.D.; Bakker, R.R.C.; Koukios, E.G.

2012-01-01

The objective of this work was to investigate the feasibility of combining low severity dilute-acid pretreatment of barley straw and decreased enzyme loading hydrolysis for the high production of fermentable substrates and the low release of inhibitory compounds. For most of the pretreatments at 160

Inductively coupled plasma optical emission spectrometry analysis of lanthanum, samarium and gadolinium oxides for rare earths impurities

International Nuclear Information System (INIS)

Reino, L.C.P.; Lordello, A.R.

1990-09-01

An inductively coupled plasma optical emission spectrometry method is described for the determination of Sm, Eu, La, Gd, Dy, Pr, Ho, Nd, Tb and Y in purified oxides of lanthanum, samarium and gadolinium. The method enables a simple, precise and readily available determination. Dissolution of the samples is achieved with diluted hydrochloric acid (1:1). The solutions are diluted to volume for a concentration of 1mg/ml. The lowest determination limit is 0,01% for most elements and 0,05 or 0,1% for a few rare earths in samarium and gadolinium matrices. Lanthanum, Samarium and Gadolinium concentrates with purity grade of 99,9%, 99,6% and 99,8%, respectively, can be analysed by this procedure. (author)

Corrosion Inhibition of Aluminium in Acid Media By Citrullus Colocynthis Extract

OpenAIRE

Chauhan, Rajkiran; Garg, Urvija; Tak, R. K.

2011-01-01

Inhibition of corrosion of aluminium in acid solution by methanol extract of Citrullus colocynthis plant has been studied using mass loss and thermometric measurements. It has been found that the plant extract act as a good corrosion inhibitor for aluminium in all concentrations of sulphuric and hydrochloric acid solution. The inhibition action depends on the concentration of acid and inhibitor. Results for mass loss and thermometric measurement indicate that inhibition efficiency increase wi...

Corrosion behaviour of WC-VC-Co hardmetals in acidic media

CSIR Research Space (South Africa)

Konadu, DS

2010-09-01

Full Text Available The effect of increasing vanadium carbide (VC) content on the corrosion behaviour of tungsten carbide – 10 wt% cobalt hard metals was investigated in 1 M hydrochloric (HCl), and sulphuric (H2SO4) acids solutions. Increasing VC content makes the open...

An AFM and XPS study of corrosion caused by micro-liquid of dilute sulfuric acid on stainless steel

International Nuclear Information System (INIS)

Wang Rongguang

2004-01-01

Micro-liquid of dilute sulfuric acid deposited on SUS304 steel surface were observed with the ac non-contact mode of an atomic force microscopy (AFM), and the detail of the corrosion process caused by them was investigated with the contact mode of the AFM, X-ray photoelectron spectroscopy (XPS) and wavelength dispersive X-ray spectroscopy (WDXS). As a result, even not applying bias voltages between the tip of the cantilever and the specimen, micro-liquid of sulfuric acid can be successfully imaged using the ac non-contact mode of AFM. Two shapes of micro-acid, i.e., micro-droplets and micro-films, were found to co-exist on the specimen surface. On areas covered by micro-films of acid, only small corrosion product particles appeared and no corrosion pits were found. Beneath micro-droplets, corrosion reaction continue to produce pits until they were all consumed to form a corrosion product (mainly iron oxides) with almost the same shape with the droplet. The total corrosion reaction time was speculated to be between 690 and 1500 ks. The corrosion product formed from micro-droplets was believed to be a process of accumulating small corrosion product particles from the liquid/substrate interface to the surface of the formerly produced corrosion product. The XPS and WDXS analysis also supports the above results

Determination of chlorine in nuclear-grade uranium compounds

International Nuclear Information System (INIS)

Yang Chunqing; Liu Fuyun; Huang Dianfan

1988-01-01

The determination of chlorine in nuclear-grade uranium compounds is discribed. Chlorine is separated from uranium oxide pyrohydrolytically with stream of wet oxygen in a furnace at 800 ∼ 900 deg C. Chlorine is volatilized as hydrochloric acid, absorbed in a dilute alkaline solution and measured with chlorine-selective electrode. This method covers the concentration range of 10 ∼ 500 pm chlorine in uranium oxide. Precision of at least ± 10% and recovery of 85 ∼ 108% have been reported

Determination of chlorine in nuclear-grade uranium compounds by ion-selective electrode

International Nuclear Information System (INIS)

Yang Chunqing; Liu Fuyun; Huang Dianfan.

1989-01-01

The determination of microamount chlorine in nuclear-grade uranium compounds is described. Chlorine is separated from uranium oxide pyrohydrolytically with stream of wet oxygen in a furnace at 800-900 deg C. Chlorine is volatilized as hydrochloric acid, which then is absorbed in a dilute alkaline solution and measured with chlorine selective electrode. This method covers the concentration range of 10-500 ppm chlorine in uranium oxide. The relative standard diviation is better than 10% and recovery of 85-108% has been reported

Optimization of dilute acid hydrolysis of Enteromorpha

Science.gov (United States)

Feng, Dawei; Liu, Haiyan; Li, Fuchao; Jiang, Peng; Qin, Song

2011-11-01

Acid hydrolysis is a simple and direct way to hydrolyze polysaccharides in biomass into fermentable sugars. To produce fermentable sugars effectively and economically for fuel ethanol, we have investigated the hydrolysis of Enteromorpha using acids that are typically used to hydrolyze biomass: H2SO4, HCl, H3PO4 and C4H4O4 (maleic acid). 5%(w/w) Enteromorpha biomass was treated for different times (30, 60, and 90 min) and with different acid concentrations (0.6, 1.0, 1.4, 1.8, and 2.2%, w/w) at 121°C. H2SO4 was the most effective acid in this experiment. We then analyzed the hydrolysis process in H2SO4 in detail using high performance liquid chromatography. At a sulfuric acid concentration of 1.8% and treatment time of 60 min, the yield of ethanol fermentable sugars (glucose and xylose) was high, (230.5 mg/g dry biomass, comprising 175.2 mg/g glucose and 55.3 mg/g xylose), with 48.6% of total reducing sugars being ethanol fermentable. Therefore, Enteromorpha could be a good candidate for production of fuel ethanol. In future work, the effects of temperature and biomass concentration on hydrolysis, and also the fermentation of the hydrolysates to ethanol fuel should be focused on.

Hydrothermal Conversion of Giant Reed to Furfural and Levulinic Acid: Optimization of the Process under Microwave Irradiation and Investigation of Distinctive Agronomic Parameters

Directory of Open Access Journals (Sweden)

Claudia Antonetti

2015-11-01

Full Text Available The hydrothermal conversion of giant reed (Arundo donax L. to furfural (FA and levulinic acid (LA was investigated in the presence of dilute hydrochloric acid. FA and LA yields were improved by univariate optimization of the main reaction parameters: concentration of the acid catalyst, solid/liquid ratio of the reaction mixture, hydrolysis temperature, and reaction time. The catalytic performances were investigated adopting the efficient microwave (MW irradiation, allowing significant energy and time savings. The best FA and LA yields were further confirmed using a traditionally heated autoclave reactor, giving very high results, when compared with the literature. Hydrolysis temperature and time were the main reaction variables to be carefully optimized: FA formation needed milder reaction conditions, while LA more severe ones. The effect of the crop management (e.g., harvest time on FA/LA production was discussed, revealing that harvest time was not a discriminating parameter for the further optimization of both FA and LA production, due to the very high productivity of the giant reed throughout the year. The promising results demonstrate that giant reed represents a very interesting candidate for a very high contemporary production of FA and LA of up to about 70% and 90% of the theoretical yields, respectively.

Desorption of uranium from titanium-activated carbon composite adsorbent with acidic eluent, 2

International Nuclear Information System (INIS)

Hirotsu, Takahiro; Fujii, Ayako; Sakane, Kohji; Katoh, Shunsaku; Sugasaka, Kazuhiko

1984-01-01

The desorption of uranium from the granular titanium-activated carbon composite adsorbent (concentration of uranium: 25.5 mg/1-Ad), which adsorbed uranium from natural sea water, was examined by the column process with acidic eluent at room temperature. The column operation was able to be carried out without destruction of the granular adsorbent by the generation of the carbon dioxide, and free from disturbance of the eluent flow by precipitate of calcium sulfate dihydrate with sulfuric acid eluent. The amount of acid consumption by the adsorbent was 0.87 eq/1-Ad. The alkaline earth metals were eluted in the range of elution volume below 2 1/1-Ad, whereas uranium, iron, and titanium were eluted above 2 1/1-Ad. Therefore, uranium was separable from the alkaline earth metals which were adsorbed in the most quantity in the adsorbent. In the range of elution volume 2 to 12 1/1-Ad, the percentage of desorbed uranium and the concentration ratio of uranium were 80 %, 680 with 0.5 N sulfuric acid, and 59 %, 490 with 0.5 N hydrochloric acid, respectively. The percentage of dissolved titanium (DTI) was 0.3 % with 0.5 N sulfuric acid, 0.26 % with 0.5 N hydrochloric acid in the same range. (author)

Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben; Hamid, Mohamed Ali

2015-01-01

The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H 3 PO 4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid. (paper)

Microtensile strength of spruce pine after exposure to acids and bases

Science.gov (United States)

F.G. Manwiller; P.R. Godfrey

1973-01-01

Earlywood and latewood microtensile specimens from 12 trees of Pinus glabra Walt. were subjected to 10-percent solution of 5 acids and 3 bases at good for up to 3 hours. Hydrochloric and sulfuric acids were the most damaging, lowering maximum tensile strength 27 and 17 percent in earlywood and 36 and 39 percent in latewood; they reduced work to maximum load 40 percent...

A Study of ext ration equilibrium in the system:phosphoric acid produced in Aqaba-uranium-0.5 M de pa-0.125M TOPO diluted in kerosene

International Nuclear Information System (INIS)

Al-Matar, K.A.; Rawajfeh, M.K.

1995-01-01

The extraction of uranium from purified wet process Jordanian phosphoric acid by synergistic solvent 0.5 M de pa and 0.125 M TOPO diluted in kerosene has been studied as a function of temperature and electro-motive force. The uranium distribution coefficient was found to be directly proportional to the electro-motive force up to a limiting point. The uranium distribution coefficient was found to decrease with temperature.Distribution coefficients for the Jordanian acid were found to be higher than those for similar acids from elsewhere.An Aqueous to Organic phase ratio (A/O) recommended for use with the Jordanian acid is 2.5. 11 refs., 6 figs., 2 tab.(Author)

Ethanol and xylitol production by fermentation of acid hydrolysate from olive pruning with Candida tropicalis NBRC 0618.

Science.gov (United States)

Mateo, Soledad; Puentes, Juan G; Moya, Alberto J; Sánchez, Sebastián

2015-08-01

Olive tree pruning biomass has been pretreated with pressurized steam, hydrolysed with hydrochloric acid, conditioned and afterwards fermented using the non-traditional yeast Candida tropicalis NBRC 0618. The main aim of this study was to analyse the influence of acid concentration on the hydrolysis process and its effect on the subsequent fermentation to produce ethanol and xylitol. From the results, it could be deduced that both total sugars and d-glucose recovery were enhanced by increasing the acid concentration tested; almost the whole hemicellulose fraction was hydrolysed when 3.77% was used. It has been observed a sequential production first of ethanol, from d-glucose, and then xylitol from d-xylose. The overall ethanol and xylitol yields ranged from 0.27 to 0.38kgkg(-1), and 0.12 to 0.23kgkg(-1) respectively, reaching the highest values in the fermentation of the hydrolysates obtained with hydrochloric acid 2.61% and 1.11%, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inhibition Effect of Deanol on Mild Steel Corrosion in Dilute ...

African Journals Online (AJOL)

The influence of deanol on the corrosion behaviour of mild steel in dilute sulphuric acid with sodium chloride addition was studied by means of mass-loss, potentiodynamic polarization, electrode potential monitoring, scanning electron microscopy and statistical analysis. Results show that deanol performed excellently with ...

Crude oil polycyclic aromatic hydrocarbons removal via clay-microbe-oil interactions: Effect of acid activated clay minerals.

Science.gov (United States)

Ugochukwu, Uzochukwu C; Fialips, Claire I

2017-07-01

Acid treatment of clay minerals is known to modify their properties such as increase their surface area and surface acidity, making them suitable as catalysts in many chemical processes. However, the role of these surface properties during biodegradation processes of polycyclic aromatic hydrocarbons (PAHs) is only known for mild acid (0.5 M Hydrochloric acid) treated clays. Four different clay minerals were used for this study: a montmorillonite, a saponite, a palygorskite and a kaolinite. They were treated with 3 M hydrochloric acid to produce acid activated clay minerals. The role of the acid activated montmorillonite, saponite, palygorskite and kaolinite in comparison with the unmodified clay minerals in the removal of PAHs during biodegradation was investigated in microcosm experiments. The microcosm experiments contained micro-organisms, oil, and clays in aqueous medium with a hydrocarbon degrading microorganism community predominantly composed of Alcanivorax spp. Obtained results indicated that acid activated clays and unmodified kaolinite did not enhance the biodegradation of the PAHs whereas unmodified montmorillonite, palygorskite and saponite enhanced their biodegradation. In addition, unmodified palygorskite adsorbed the PAHs significantly due to its unique channel structure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Procedure for the preparation of a radiodiagnostic agent for skeletal scintigraphy

International Nuclear Information System (INIS)

Budsky, F.; Kopecky, P.; Prokop, J.

1997-01-01

The procedure for the preparation of a radiodiagnostic agent based on an aminomethylphosphonic acid and 99m Tc is as follows: One mol of high-purity diethylenetriamine trihydrochloride, which is obtained by precipitating diethylenetriamine in methanol with azeotropic hydrochloric acid, and 5.3 mol of orthophosphoric acid are dissolved in 2 mol of azeotropic hydrochloric acid at 100-110 degC and reacted with a 34%-36% formaldehyde solution (5.6 mol) at the same temperature for a minimum of 60 min. The mixture is purified by repeated extraction with pentanol at 50 degC and evaporated to dryness. The residue is suspended in isopropanol and the suspension is evaporated to dryness again. The residue is boiled consecutively with dimethylformamide and with glacial acetic acid, dissolved in water, and precipitated with methanol to obtain diethylenetriamino-N,N,N',N',N''-pentakis(methylenephosphonic) acid (DTPMP). This product is filtered out, rinsed with methanol, and dried over sulfuric acid at 3 kPa for 3-5 days. The medical form is prepared by dissolving calcium carbonate in 0.1-1M aqueous DTPMP so that the two chemicals are in the molar ratio 1:1, and the solution is neutralized with sodium hydroxide so that the hydroxide-to-DTPMP molar ratio is 3:1. To the solution, freed from dissolved oxygen, a solution of tin dichloride in dilute hydrochloric acid is added so that the tin-to-DTPMP molar ratio is 1:10 to 2:10. Sodium hydroxide is added in order to exactly neutralize the hydrochloric acid, and the solution is subjected to sterile filtration and filled in vials. Each vial will contain 15-25 μmol DTPMP. The medical form is a lyophilisate of the monocalcium-trisodium salt of diethyleneamino-N,N,N',N',N''-pentakis(methylenephosphonic) salt and its complex with divalent tin. The radiodiagnostic agent is prepared by dissolving in the vial the eluate from a 99m Tc generator (0.25-5 ml) at activities of 250-2500 MBq. The Tc complex so obtained will be stable for a minimum

LIXIVIAÇÃO ÁCIDA DE BATERIAS ÍON-LÍTIO

Directory of Open Access Journals (Sweden)

Rafael Gundim Silva

Full Text Available This paper describes a route for recovering cobalt and lithium from spent Li-ion batteries via acidic leaching. Sulfuric, hydrochloric, hydrofluoric and formic acids were used as leachants. Hydrogen peroxide was added as reductant, except for formic acid since it is itself a reductant. Experiments were run at 25-40 ºC for 1-3 h. Under the best optimal conditions, the leaching efficiency order was HCl ≈ HF > H2SO4 > HCOOH. Over 90 wt.% of cobalt and lithium were leached by the inorganic acids. The insoluble matter corresponds mainly to the carbon from the cathode. Co(II was extracted with D2EHPA 16 vol.% diluted in n-hexane at pH ~5 (A/O ratio 1/1 vol/vol, one stage, 25 ºC. Co(II striping was possible using a dilute leachant (1-2 mol L-1 HCl or H2SO4, 4-5 mol L-1 HF or HCOOH. Lithium was isolated from the raffinate by precipitation as carbonate or phosphate.

Enrichment of boron 10

International Nuclear Information System (INIS)

Coutinho, C.M.M.; Rodrigues Filho, J.S.R.; Umeda, K.; Echternacht, M.V.

1990-01-01

A isotopic separation pilot plant with five ion exchange columns interconnected in series were designed and built in the IEN. The columns are charged with a strong anionic resin in its alkaline form. The boric acid solution is introduced in the separation columns until it reaches a absorbing zone length which is sufficient to obtain the desired boron-10 isotopic concentration. The boric acid absorbing zone movement is provided by the injection of a diluted hydrochloric acid solution, which replace the boric acid throughout the columns. The absorbing zone equilibrium length is proportional to its total length. The enriched boron-10 and the depleted boron are located in the final boundary and in the initial position of the absorbing zones, respectively. (author)

Extraction of some acids using aliphatic amines

International Nuclear Information System (INIS)

Matutano, L.

1964-06-01

Hydrochloric, nitric, sulphuric, perchloric, phosphoric, acetic and formic acids in aqueous solution (0.05 to 10 M) are extracted by amberlite LA2 and trilaurylamine in solution, 5 per cent by volume, in kerosene and xylene respectively. The extraction process consists of: neutralization of the amine salt; a 'molecular extraction', i.e. an extraction using an excess of acid with respect to the stoichiometry of the amine salt. According to the behaviour of the acid during the extraction, three groups may be distinguished: completely dissociated acids, carboxylic acids, phosphoric acid. This classification is also valid for the extraction of the water which occurs simultaneously with that of the acid. An extraction mechanism is put forward for formic acid and the formation constant of its amine salt is calculated. (author) [fr

Method of decontaminating radioactive-contaminated instruments

International Nuclear Information System (INIS)

Urata, Megumu; Fujii, Masaaki; Kitaguchi, Hiroshi.

1982-01-01

Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode. (Yoshino, Y.)

Photo-oxidation of gaseous ethanol on photocatalyst prepared by acid leaching of titanium oxide/hydroxyapatite composite

Energy Technology Data Exchange (ETDEWEB)

Ono, Y., E-mail: ono-y@kanagawa-iri.go.jp [Mechanical and Material Engineering Division, Kanagawa Industrial Technology Center, Ebina, Kanagawa 243-0435 (Japan); Rachi, T.; Yokouchi, M.; Kamimoto, Y. [Mechanical and Material Engineering Division, Kanagawa Industrial Technology Center, Ebina, Kanagawa 243-0435 (Japan); Nakajima, A. [Department of Metallurgy and Ceramics Science, Tokyo Institute of Technology, Meguro, Tokyo 152-8552 (Japan); Okada, K. [Materials and Structures Laboratory, Tokyo Institute of Technology, Midori, Yokohama, Kanagawa 226-8503 (Japan)

2013-06-01

Highlights: ► Photocatalyst powder was prepared by acid leaching of TiO{sub 2}/apatite composite. ► The photocatalytic activity was evaluated from in situ FT-IR study using ethanol. ► Apatite in the composite had positive effect for the photo-oxidation of ethanol. ► The enhanced oxidation rate was explained by the difference in deactivation rate. - Abstract: Highly active photocatalysts were synthesized by leaching of heat-treated titanium dioxide (TiO{sub 2})/hydroxyapatite (HAp) powder with hydrochloric acid at 0.25, 0.50, 0.75 mol/l, and their photocatalytic activities were evaluated from in situ Fourier transform infrared (FT-IR) study of photo-oxidation of gaseous ethanol. By changing the acid concentration, the TiO{sub 2}/HAp composite had different atomic ratios of Ca/Ti (0.0–2.8) and P/Ti (0.3–2.1). It was found that phosphate group remained on the surface of TiO{sub 2} particle even in the sample treated with concentrated acid (0.75 mol/l). These acid-treated samples showed higher rates for ethanol photo-oxidation than the commercial TiO{sub 2} powder, Degussa P25. The highest rate was obtained in the TiO{sub 2}/HAp composite treated with the dilute (0.25 mol/l) acid in spite of its low content of TiO{sub 2} photocatalyst. This enhanced photocatalytic activity was attributed to the result that the deactivation with repeated injections of ethanol gas was suppressed in the TiO{sub 2}/HAp composites compared with the TiO{sub 2} powders.

Cellulose with a High Fractal Dimension Is Easily Hydrolysable under Acid Catalysis

Directory of Open Access Journals (Sweden)

Mariana Díaz

2017-05-01

Full Text Available The adsorption of three diverse amino acids couples onto the surface of microcrystalline cellulose was studied. Characterisation of modified celluloses included changes in the polarity and in roughness. The amino acids partially break down the hydrogen bonding network of the cellulose structure, leading to more reactive cellulose residues that were easily hydrolysed to glucose in the presence of hydrochloric acid or tungstophosphoric acid catalysts. The conversion of cellulose and selectivity for glucose was highly dependent on the self-assembled amino acids adsorbed onto the cellulose and the catalyst.

Comparison of aqueous ammonia and dilute acid pretreatment of bamboo fractions: Structure properties and enzymatic hydrolysis.

Science.gov (United States)

Xin, Donglin; Yang, Zhong; Liu, Feng; Xu, Xueru; Zhang, Junhua

2015-01-01

The effect of two pretreatments methods, aqueous ammonia (SAA) and dilute acid (DA), on the chemical compositions, cellulose crystallinity, morphologic change, and enzymatic hydrolysis of bamboo fractions (bamboo yellow, timber, green, and knot) was compared. Bamboo fractions with SAA pretreatment had better hydrolysability than those with DA pretreatment. High crystallinity index resulted in low hydrolysis yield in the conversion of SAA pretreated bamboo fractions, not DA pretreated fractions. The increase of cellulase loading had modestly positive effect in the hydrolysis of both SAA and DA pretreated bamboo fractions, while supplement of xylanase significantly increased the hydrolysis of the pretreated bamboo fractions, especially after SAA pretreatment. The results indicated that SAA pretreatment was more effective than DA pretreatment in conversion of bamboo fractions, and supplementation of xylanase was necessary in effective conversion of the SAA pretreated fractions into fermentable sugars. Copyright © 2014 Elsevier Ltd. All rights reserved.

Determination of cadmium in aluminium by atomic absorption spectrometry

International Nuclear Information System (INIS)

Batistoni, D.A.; Erlijman, L.H.

1978-12-01

A direct method for the determination of cadmium in elemental aluminium is described. Metal samples are dissolved in diluted hydrochloric acid and cadmium is determined by atomic absorption spectrometry in an air-acetylene flame. Interference by non-specific absorption observed at the analytical wavelength incorrected for by means of a non-absorbing line emitted by the hollow-cathode lamp. Relatively large amounts of arsenic do not interfere. The minimun determinable concentration of cadmium for this procedure is 2-3 ppm, expressed on aluminium basis. (author) [es

Removal of cobalt ion from bentonite using diffusion dialysis

International Nuclear Information System (INIS)

Takase, Hisao; Tamura, Kouichi; Katoh, Naotake

1995-01-01

A radioactive metal ion must be removed from contaminated soil which accidentally adsorbs the radioactive metal ion. With this situation, the authors examined the diffusion dialysis as a removal process of the radioactive ion from fine particles of the soil. In a dialyzer, the one side of the solution including fine particles of soil was referred to as diluting cell and the other side stripping was referred to as concentrating cell. The experiments by batch operations were carried out by interposing a cation exchange membrane (CMV) between both cells. The high separation of the ion from the soil could be achieved by the experiments when the aqueous solution of hydrochloric acid was used as stripping solution. Equations for batch diffusion dialysis system were set up and calculated. From the results of simulation, it was noted that the concentration of hydrochloric acid in the stripping solution, the selections of the membrane, and mass transfer coefficient at the surface of the membrane strongly affect the removal efficiency of the ion. (author)

Dissolution mechanism of aluminum hydroxides in acid media

Science.gov (United States)

Lainer, Yu. A.; Gorichev, I. G.; Tuzhilin, A. S.; Gololobova, E. G.

2008-08-01

The effects of the concentration, temperature, and potential at the hydroxide/electrolyte interface on the aluminum hydroxide dissolution in sulfuric, hydrochloric, and perchloric acids are studied. The limiting stage of the aluminum hydroxide dissolution in the acids is found to be the transition of the complexes that form on the aluminum hydroxide surface from the solid phase into the solution. The results of the calculation of the acid-base equilibrium constants at the oxide (hydroxide)/solution interface using the experimental data on the potentiometric titration of Al2O3 and AlOOH suspensions are analyzed. A mechanism is proposed for the dissolution of aluminum hydroxides in acid media.

Brewing Bokashi: Strengthening Student Skills in Dilution Theory through Fermentation Analysis

Directory of Open Access Journals (Sweden)

Robert E. Zdor

2016-05-01

Full Text Available One of the basic microbiological techniques that students should master is that of using dilution theory to calculate the levels of bacteria in a fluid. This tip reports on using a rice water-milk fermentation mixture termed Bokashi as an easily implemented exercise in the basic microbiological lab to give students multiple opportunities to use dilution theory. Due to the shifts in bacterial community composition over time, a variety of microbes can be cultured using selective and nonselective media. Microscopic observation and the use of GEN III microplates to determine the collective phenotypic pattern of the mixture both give additional opportunities for students to hone their skills in bacterial analysis. Due to the decrease in the pH of the mixture over time, the notion of acid tolerance in bacteria can be explored and assessed using the microplate. By performing multiple rounds of serial dilutions and spread plating, students can practice their skill at using dilution theory several times over the course of the exercise.

Molecular analysis of two mouse dilute locus deletion mutations: Spontaneous dilute lethal20J and radiation-induced dilute prenatal lethal Aa2 alleles

International Nuclear Information System (INIS)

Strobel, M.C.; Seperack, P.K.; Copeland, N.G.; Jenkins, N.A.

1990-01-01

The dilute (d) coat color locus of mouse chromosome 9 has been identified by more than 200 spontaneous and mutagen-induced recessive mutations. With the advent of molecular probes for this locus, the molecular lesion associated with different dilute alleles can be recognized and precisely defined. In this study, two dilute mutations, dilute-lethal20J (dl20J) and dilute prenatal lethal Aa2, have been examined. Using a dilute locus genomic probe in Southern blot analysis, we detected unique restriction fragments in dl20J and Aa2 DNA. Subsequent analysis of these fragments showed that they represented deletion breakpoint fusion fragments. DNA sequence analysis of each mutation-associated deletion breakpoint fusion fragment suggests that both genomic deletions were generated by nonhomologous recombination events. The spontaneous dl20J mutation is caused by an interstitial deletion that removes a single coding exon of the dilute gene. The correlation between this discrete deletion and the expression of all dilute-associated phenotypes in dl20J homozygotes defines the dl20J mutation as a functional null allele of the dilute gene. The radiation-induced Aa2 allele is a multilocus deletion that, by complementation analysis, affects both the dilute locus and the proximal prenatal lethal-3 (pl-3) functional unit. Molecular analysis of the Aa2 deletion breakpoint fusion fragment has provided access to a previously undefined gene proximal to d. Initial characterization of this new gene suggests that it may represent the genetically defined pl-3 functional unit

What infusion flow should be used for mid-dilution hemodiafiltration?

Science.gov (United States)

Maduell, Francisco; Arias, Marta; Fontseré, Néstor; Vera, Manel; Masso, Elisabeth; Garro, Julia; Barros, Xoana; Martina, Maria N; Elena, Montserrat; Bergadá, Eduardo; Cases, Aleix; Bedini, Jose Luis; Campistol, Josep M

2010-01-01

There is still no consensus on the optimal infusion flow (Qi) in mid-dilution hemodiafiltration. The aim of this study was to compare mid-dilution with varying Qi. Prospective study in 25 patients who underwent seven hemodialysis sessions with a Qi of 0, 50, 100, 150, 200, 250 and 300 ml/min. All sessions were well tolerated except Qi 300 ml/min. No significant differences in urea, creatinine, alpha(1)-microglobulin or alpha(1)-acid glycoprotein reduction ratios were observed. beta(2)-Microglobulin, myoglobin and prolactin reduction ratios were higher with Qi 150, 200, 250 and 300 ml/min in comparison with Qi of 0, 50 and 100 ml/min. There were no differences in the removal of small or larger molecules when Qi was 150 ml/min or higher. Optimal Qi in mid-dilution appears to be in the range of 150-250 ml/min since good clinical outcomes, similar efficiency and no technical complications up to a Qi of 250 ml/min were observed.

Effect of Oxidation Degree on Valence Change and Distribution of Octahedral Fe Element in Biotite

Directory of Open Access Journals (Sweden)

Li Ziqian

2017-01-01

Full Text Available In this paper, the valence change and distribution of iron elements in octahedral vacancies of biotite were studied in the oxidation process. The biotite and saturated barium nitrate solution were mixed in dilute hydrochloric acid under hydrothermal reaction conditions, the solid after reaction was used as the test sample. Firstly, the remainder potassium and iron content were measured by atomic absorption spectrometry(AAS. Secondly, the state of iron along with oxidation degree increased was analyzed, in addition, the phase composition and the change of layer spacing in samples was detected by X-ray diffraction(XRD. Thirdly, The variation mode of Si-O bond were characterized by Fourier transform infrared spectroscopy(FT-IR.This research was adopted hydrogen ions in diluted hydrochloric acid and nitrate ions in barium nitrate to provide oxidation environment for reaction, and the oxidation degree was controlled by adjusted the amount of hydrogen ion introduced. We found out that the amount of hydrogen ion is positively correlated with oxidation degree in biotite, and the deeper oxidation degree in biotite, the lower electronegativity of singer layer. Potassium and iron element would be release out of micaceous structure during the biotite oxidation. The higher the oxidation degree is, the greater the releasing happen. The charge density combining Fe oxidation and releasing firstly increased then decreased with the oxidation degree turned greater. During the oxidation, the Si-O vibrated would change from parallel layer vibration model to vertical vibration model.

Desorption of uranium from titanium-activated carbon composite adsorbent with acidic eluent, 1

International Nuclear Information System (INIS)

Hirotsu, Takahiro; Fujii, Ayako; Sakane, Kohji; Katoh, Shunsaku; Sugasaka, Kazuhiko

1984-01-01

An investigation was carried out on the desorption of uranium from titanium-activated carbon composite adsorbent with acidic eluent by the batch process. The rate of desorption of uranium with acidic eluent depended on temperature, showing an increase as the temperature was raised. But the rate of desorption with acidic eluent was less dependent on temperature than that obtained when mixed eluent of sodium carbonate-sodium hydrogencarbonate was used. The rate of desorption of uranium did not vary in the range of concentration from 0.3 to 0.5 N, and the rate of desorption with sulfuric acid was slightly higher than that obtained when hydrochloric acid was used. The amount of dissolved titanium decreased as the ratio of adsorbent to eluent (RAE) was increased. At RAE of 10 %, the percentage of dissolved titanium (DTI) was below 0.38 % with sulfuric acid, below 0.7 % with hydrochloric acid. These values were found to be higher than the ones with the carbonate eluent. The elements except uranium, which were adsorbed on the adsorbent, were eluted simultaneously with acidic eluent. The regeneration of the adsorbent after desorption, therefore, was found to be unnecessary. In a repeated test of adsorption-desorption treatment up to five times, the percentage of uranium adsorbed from natural sea water was approximately constant of 85 %. From these results, the application of column process to the desorption of uranium with acidic eluent at room temperature was proposed to be feasible. (author)

Desorption of uranium from titanium-activated carbon composite adsorbent with acidic eluent, (1)

International Nuclear Information System (INIS)

Hirotsu, Takahiro; Fujii, Ayako; Sakane, Kohji; Katoh, Shunsaku; Sugasaka, Kazuhiko

1983-01-01

An investigation was carried out on the desorption of uranium from titanium-activated carbon composite adsorbent with acidic eluent by the batch process. The rate of desorption of uranium with acidic eluent depended on temperature, showing an increase as the temperature was raised. But the rate of desorption with acidic eluent was less dependent on temperature than that obtained when mixed eluent of sodium carbonate-sodium hydrogencarbonate was used. The difference of the rate of desorption of uranium in the range of concentration from 0.3 to 0.5N was not found, and the rate of desorption with sulfuric acid was slightly higher than that obtained when hydrochloric acid was used. The amount of dissolved titanium decreased as the ratio of adsorbent to eluent (RAE) was increased. At RAE of 10%, the percentage of dissolved titanium (DTI) was below 0.38% with sulfuric acid, below 0.7% with hydrochloric acid. These values were found to be higher than the ones with the carbonate eluent. The elements except uranium, which were adsorbed on the adsorbent, were eluted simultaneously with acidic eluent. The regeneration of the adsorbent after desorption, therefore, was found to be unnecessary. In a repeated test of adsorption-desorption treatment up to five times, the percentage of uranium adsorbed from natural sea water was approximately constant of 85%. From these results, the application of column process to the desorption of uranium with acidic eluent at room temperature was proposed to be feasible. (author)

Hybridizing pines with diluted pollen

Science.gov (United States)

Robert Z. Callaham

1967-01-01

Diluted pollens would have many uses by the tree breeder. Dilutions would be particularly advantageous in making many controlled pollinations with a limited amount of pollen. They also would be useful in artificial mass pollinations of orchards or single trees. Diluted pollens might help overcome troublesome genetic barriers to crossing. Feasibility o,f using diluted...

Acetic acid extraction from aqueous solutions using fatty acids

NARCIS (Netherlands)

IJmker, H.M.; Gramblicka, M.; Kersten, Sascha R.A.; van der Ham, Aloysius G.J.; Schuur, Boelo

2014-01-01

A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

Semicarbazide in Canadian bakery products.

Science.gov (United States)

Becalski, A; Lau, B P-Y; Lewis, D; Seaman, S

2006-02-01

Levels of semicarbazide were determined by liquid chromatography-tandem mass spectrometry using isotope dilution ((13)C(15)N(2)-semicarbazide) methodology, and they were measured, after hydrolysis in 0.125 M hydrochloric acid and derivatization with 2-nitrobenzaldehyde, as a sum of free and bound semicarbazide. Levels of semicarbazide in 11 bakery products, which were sampled at three time intervals from the same source, varied from not detected (product, at times more than tenfold, suggesting that the addition of azodicarbonamide to the same product is not standardized in many baking establishments.

Neutron activation analysis for antimetabolites. [in food samples

Science.gov (United States)

1973-01-01

Determination of metal ion contaminants in food samples is studied. A weighed quantity of each sample was digested in a concentrated mixture of nitric, hydrochloric and perchloric acids to affect complete solution of the food products. The samples were diluted with water and the pH adjusted according to the specific analysis performed. The samples were analyzed by neutron activation analysis, polarography, and atomic absorption spectrophotometry. The solid food samples were also analyzed by neutron activation analysis for increased sensitivity and lower levels of detectability. The results are presented in tabular form.

Tantalum-178 - a short-lived nuclide for nuclear medicine: development of a potential generator system

International Nuclear Information System (INIS)

Neirinckx, R.D.; Jones, A.G.; Davis, M.A.; Harris, G.I.; Holman, B.L.

1978-01-01

We describe a chemical separation that may form the basis of a generator system for the short-lived radionuclide Ta-178 (T/sub 1/2/ = 9 min). The parent nuclide W-178 (T/sub 1/2/ = 21.7 days) is loaded on an anion-exchange column and the daughter eluted with a mixture of dilute hydrochloric acid and hydrogen peroxide. The yields of tantalum and the breakthrough of the tungsten parent as a function of the eluting conditions are discussed, and preliminary animal distribution data are presented for various treatments of the eluant solution

Gastroesophageal scintigraphy in patients with gastroesophageal reflux: comparison with manometry and with acid reflux test

International Nuclear Information System (INIS)

Bouvard, G.; Baptiste, J.C.; Peres, J.C.; Segol, P.; Fernandez, Y.

1985-01-01

Gastroesophageal scintiscanning offers several advantages: it is more physiological and more convenient than acid reflux test, does not require nasogastric intubation or installation of hydrochloric acid into the stomach; its diagnostic value is satisfactory (very good specificity and sensitivity); it can be easily repeated and permits a semi-quantitative evaluation of the reflux and a discrimination between physiological and pathological gastroesophageal reflux [fr

Gastroesophageal scintigraphy in patients with gastroesophageal reflux: comparison with manometry and with acid reflux test

Energy Technology Data Exchange (ETDEWEB)

Bouvard, G.; Baptiste, J.C.; Peres, J.C.; Segol, P.; Fernandez, Y.

1985-01-01

Gastroesophageal scintiscanning offers several advantages: it is more physiological and more convenient than acid reflux test, does not require nasogastric intubation or installation of hydrochloric acid into the stomach; its diagnostic value is satisfactory (very good specificity and sensitivity); it can be easily repeated and permits a semi-quantitative evaluation of the reflux and a discrimination between physiological and pathological gastroesophageal reflux.

Determination of the Thermodynamic Properties of Poly [2-(3-phenyl-3-methylcyclobutyl)-2-hydroxyethyl methacrylate-co-methacrylic acid] at Infinite Dilution by Inverse Gas Chromatography

OpenAIRE

KAYA, İsmet

2014-01-01

Some thermodynamic quantities were obtained for the interactions of poly [2-(3-phenyl -3- methylcyclobutyl)-2-hydroxyethyl methacrylate-co-methacrylic acid] Poly (PCHEMA-co-MA) with alcohols, ketones, acetates, aromatics and n-alkanes by inverse gas chromatography in the temperature range of 150-180oC. The specific retention volumes, Vgo, weight fraction activity coefficients of solute probes at infinite dilution, W1\\infty and Flory-Huggins thermodynamic interaction parameters, c12...

The effects of alfalfa particle size and acid treated protein on ruminal ...

African Journals Online (AJOL)

This study was conducted to investigate the effects of alfalfa particle size (long vs. fine) and canola meal treated with hydrochloric acid solution (untreated vs treated) on ruminal chemical composition, liquid, particulate, escapable and non escapable phases in Zel sheep. Four ruminally cannulated sheep received a mixed ...

Optimization of Alkaline and Dilute Acid Pretreatment of Agave Bagasse by Response Surface Methodology

Science.gov (United States)

Ávila-Lara, Abimael I.; Camberos-Flores, Jesus N.; Mendoza-Pérez, Jorge A.; Messina-Fernández, Sarah R.; Saldaña-Duran, Claudia E.; Jimenez-Ruiz, Edgar I.; Sánchez-Herrera, Leticia M.; Pérez-Pimienta, Jose A.

2015-01-01

Utilization of lignocellulosic materials for the production of value-added chemicals or biofuels generally requires a pretreatment process to overcome the recalcitrance of the plant biomass for further enzymatic hydrolysis and fermentation stages. Two of the most employed pretreatment processes are the ones that used dilute acid (DA) and alkaline (AL) catalyst providing specific effects on the physicochemical structure of the biomass, such as high xylan and lignin removal for DA and AL, respectively. Another important effect that need to be studied is the use of a high solids pretreatment (≥15%) since offers many advantaged over lower solids loadings, including increased sugar and ethanol concentrations (in combination with a high solids saccharification), which will be reflected in lower capital costs; however, this data is currently limited. In this study, several variables, such as catalyst loading, retention time, and solids loading, were studied using response surface methodology (RSM) based on a factorial central composite design of DA and AL pretreatment on agave bagasse using a range of solids from 3 to 30% (w/w) to obtain optimal process conditions for each pretreatment. Subsequently enzymatic hydrolysis was performed using Novozymes Cellic CTec2 and HTec2 presented as total reducing sugar (TRS) yield. Pretreated biomass was characterized by wet-chemistry techniques and selected samples were analyzed by calorimetric techniques, and scanning electron/confocal fluorescent microscopy. RSM was also used to optimize the pretreatment conditions for maximum TRS yield. The optimum conditions were determined for AL pretreatment: 1.87% NaOH concentration, 50.3 min and 13.1% solids loading, whereas DA pretreatment: 2.1% acid concentration, 33.8 min and 8.5% solids loading. PMID:26442260

Determination of diphenylarsinic acid, phenylarsonic acid and inorganic arsenic in drinking water by graphite-furnace atomic-absorption spectrometry after simultaneous separation and preconcentration with solid-phase extraction disks.

Science.gov (United States)

Hagiwara, Kenta; Inui, Tetsuo; Koike, Yuya; Nakamura, Toshihiro

2013-01-01

A simple method of graphite-furnace atomic-absorption spectrometry (GFAAS) after solid-phase extraction (SPE) was developed for the determination of diphenylarsinic acid (DPAA), phenylarsonic acid (PAA), and inorganic arsenic (iAs) in drinking water. This method involves the simultaneous collection of DPAA, PAA, and iAs using three stacked SPE disks, i.e., an Empore SDB-XD disk (the upper layer), an activated carbon disk (the middle layer), and a Cation-SR disk loaded with Zr and Ca (ZrCa-CED; the lower layer). A 200-mL aqueous sample was adjusted to pH 3 with nitric acid and passed through the SPE disks at a flow rate of 15 mL min(-1), to concentrate DPAA on the SDB-XD disk, PAA on the activated carbon disk, and iAs on the ZrCa-CED. The As compounds were eluted from the disks with 10 mL of ethanol containing 0.5 mol L(-1) ammonia solution for DPAA, 20 mL of 1 mol L(-1) ammonia solution for PAA, and 20 mL of 6 mol L(-1) hydrochloric acid for iAs. The eluates of DPAA, PAA, and iAs were diluted to 20, 25, and 25 mL, respectively, with deionized water, and then analyzed by GFAAS. The detection limits of As (three-times the standard deviation (n = 3) of the blank values) were 0.13 and 0.16 μg L(-1) at enrichment factors of 10 and 8, respectively, using a 200-mL water sample. Spike tests with 2 μg (10 μg L(-1)) of DPAA, PAA, and iAs in 200 mL of tap water and bottled drinking water showed good recoveries (96.1-103.8%).

An Effective Acid Combination for Enhanced Properties and Corrosion Control of Acidizing Sandstone Formation

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben

2016-01-01

To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing. (paper)

Recovery of calcium carbonate from steelmaking slag and utilization for acid mine drainage pre-treatment

CSIR Research Space (South Africa)

Mulopo, J

2012-06-01

Full Text Available The conversion of steelmaking slag (a waste product of the steelmaking process) to calcium carbonate (CaCO3) was tested using hydrochloric acid, ammonium hydroxide and carbon dioxide via a pH-swing process. Batch reactors were used to assess...

An on-line dilution system for spectrometry using an inductively coupled plasma source

International Nuclear Information System (INIS)

Moore, G.L.; Watson, A.E.; Humphries-Cuff, P.J.

1982-01-01

An on-line dilution system that uses a two-channel peristaltic pump to feed a GMK Babington type of nebulizer is described. By the use of a diluent containing the appropriate concentrations of acid, sodium, and internal standard element, which was fed at a constant rate to the nebulizer, the system produced analytical results that are not significantly different (less than 3 per cent relative) from those obtained with the normal dilution technique. However, a considerable saving in time is achieved, as well as a saving in the use of expensive reagents

Bias due to Preanalytical Dilution of Rodent Serum for Biochemical Analysis on the Siemens Dimension Xpand Plus

Directory of Open Access Journals (Sweden)

Jennifer L. Johns

2018-02-01

Full Text Available Clinical pathology testing of rodents is often challenging due to insufficient sample volume. One solution in clinical veterinary and exploratory research environments is dilution of samples prior to analysis. However, published information on the impact of preanalytical sample dilution on rodent biochemical data is incomplete. The objective of this study was to evaluate the effects of preanalytical sample dilution on biochemical analysis of mouse and rat serum samples utilizing the Siemens Dimension Xpand Plus. Rats were obtained from end of study research projects. Mice were obtained from sentinel testing programs. For both, whole blood was collected via terminal cardiocentesis into empty tubes and serum was harvested. Biochemical parameters were measured on fresh and thawed frozen samples run straight and at dilution factors 2–10. Dilutions were performed manually, utilizing either ultrapure water or enzyme diluent per manufacturer recommendations. All diluted samples were generated directly from the undiluted sample. Preanalytical dilution caused clinically unacceptable bias in most analytes at dilution factors four and above. Dilution-induced bias in total calcium, creatinine, total bilirubin, and uric acid was considered unacceptable with any degree of dilution, based on the more conservative of two definitions of acceptability. Dilution often caused electrolyte values to fall below assay range precluding evaluation of bias. Dilution-induced bias occurred in most biochemical parameters to varying degrees and may render dilution unacceptable in the exploratory research and clinical veterinary environments. Additionally, differences between results obtained at different dilution factors may confound statistical comparisons in research settings. Comparison of data obtained at a single dilution factor is highly recommended.

Determination of gamma-aminobutyric acid in food matrices by isotope dilution hydrophilic interaction chromatography coupled to mass spectrometry.

Science.gov (United States)

Zazzeroni, Raniero; Homan, Andrew; Thain, Emma

2009-08-01

The estimation of the dietary intake of gamma-aminobutyric acid (GABA) is dependent upon the knowledge of its concentration values in food matrices. To this end, an isotope dilution liquid chromatography-mass spectrometry method has been developed employing the hydrophilic interaction chromatography technique for analyte separation. This approach enabled accurate quantification of GABA in apple, potato, soybeans, and orange juice without the need of a pre- or post-column derivatization reaction. A selective and precise analytical measurement has been obtained with a triple quadrupole mass spectrometer operating in multiple reaction monitoring using the method of standard additions and GABA-d(6) as an internal standard. The concentrations of GABA found in the matrices tested are 7 microg/g of apple, 342 microg/g of potatoes, 211 microg/g of soybeans, and 344 microg/mL of orange juice.

Spectroscopic studies and thermal analysis of mononuclear metal complexes with moxifloxacin and 2,2‧-bipyridine and their effects on acute lung injury induced by hydrochloric acid in rats

Science.gov (United States)

El-Hamid, S. M. Abd; El-Demerdash, R. S.; Arafat, H. F. H.; Sadeek, S. A.

2017-12-01

The article describes the interaction of Y(III), Zr(IV), La(III), Ce(IV) and U(VI) with moxifloxacin hydrochloride and 2,2‧-bipyridine. Characterization of complexes was made by elemental analyses, molar conductivity, magnetic moment measurements and spectral measurements e.g. IR, UV-Vis., 1H NMR and mass as well as thermal analyses (TG and DTG). The molar conductivity shows that the complexes are electrolytes nature. Spectroscopic investigation of the solid complexes studied here indicate that moxifloxacin hydrochloride and 2,2‧-bipyridine are coordinated to the metal ions in a neutral bidentate manner. After complete characterization, the chemical formulae of the complexes were established. The calculated bond length and force constant, F(Udbnd O), in the uranyl complex are 1.756 Å and 637.90 Nm-1, respectively. Kinetic and thermodynamic parameters were determined using Coats-Redfern and Horowitz-Metzger equations. Establishment of hydrochloric acid that induce acute lung injury (ALI) in rats by intratracheal administration through damaging the alveolar epithelium and activation of the neutrophil and subsequent oxidative stress by increasing malondialdehyde (MDA), tumor necrosis factor (TNF-α) and neutrophil, which were confirmed by histopathological investigation while decreasing in antioxidant enzymes and lymphocytes. Whereas treatment with mixed-ligand metal complexes significantly decrease MDA, TNF-α and neutrophils and increase antioxidant and lymphocytes.

Extraction of Collagen from Chicken Feet with Various Acidic Solutions and Soaking Time

Directory of Open Access Journals (Sweden)

Prayitno Prayitno

2007-05-01

Full Text Available The objective of this research was to know the ability of various acidic solutions on dissolving collagen  chicken feet, with different soaked time.  Each acid 5 percent (v/v, collagen extraction was done by washing chicken feet and then cutted into small pieces and finally grinded.  Every 100 gram treatment was soaked in acetic acid (a1, citric acid (a2, lactic acid (a3 and hydrochloric acid (a4, for 12, 24 and 36 hours.  Precipitated collagen in the filtrate was 5 percent NaOH to reach the neutral pH (pH 7.  Collagen precipitate was separated by filtration usingfilter paper and then  rendement was calculated, HPLC was used to determin amino acid composition, and SDS-PAGE was use determin the type of collagen.  This experiment use factorial completely randomized design (CRD 4 x 3 and three time replication.   Result showed that lactic acid has highest capability to dissolve collagen, while citric acid the lowest.  Combination of acid solution and soaking time had significant (P<0.01 effect on dissolving collagen of chicken feet.  Extracted collagen in all acid solution, hassame amino acid, composition but different in percentage of amino acid molecules.  Collagen type in treatment combination was the same, but for soaking time of 36 hours revealed some peptide band.  Lactic acid had highest capability of collagen extraction in chicken feet than citric acid, acetic acid and hydrochloric acid with soaking time of 12, 24 and 36 hours.  It was estimated that extracted collagen can be grouped to type I consisted of two chain of a1. (Animal Production 9(2: 99-104 (2007   Key Words : Chicken feet, acids, soaking time, collagen

Evaluation of new techniques of acidizing in western Canada

Energy Technology Data Exchange (ETDEWEB)

Cruikshank, C G

1968-01-01

During the period 1960 to 1968, stimulation with acid has gained prominence throught the development and introduction of new acidizing techniques in W. Canada. Many new products and ideas have been tried but only a limited number have gained a permanent place in the stimulation field. Acidizing with mixtures of acid and alcohol has been accepted because of better post treatment cleanup of the formation. Uses of the gases, nitrogen and carbon dioxide in conjunction with acid treatments to give deep penetration and fast cleanup with savings in rig costs have proved successful. Treatments with high strength Hydrochloric acid provides a very economical means to get deep acid penetration. Combining treatment technology, laboratory evaluations, well and reservoir information with past history when available is an essential ingredient for good treatment design.

Studying titanium-molybdenum-zirconium alloys of increased corrosion resistance in acid solutions

International Nuclear Information System (INIS)

Tomashov, N.D.; Kazarin, V.I.; Mikheev, V.S.; Goncharenko, B.A.; Sigalovskaya, T.M.; Kalyanova, M.P.

1977-01-01

New promising Ti-Mo-Nb-Zr system alloys, possessing good workability and a high corrosion resistance in non-oxidizing solutions of acids, have been developed. The alloys may be recommended as structural materials for equipment operating in severely agressive acid media, such as hydrochloric, sulphuric and phosphoric acids. The corrosion resistance of alloys of the above system in solutions of H 2 SO 4 , HCl and H 3 PO 4 acids may be maximized by increasing the overall alloying to 42% (keeping the ratio of the alloying components Mo/Nb/Zr=4/1/1 unchanged), while retaining sufficiently good plasticity and workability

Optimization of alkaline and dilute acid pretreatment of agave bagasse by response surface methodology

Directory of Open Access Journals (Sweden)

Abimael I. Ávila-Lara

2015-09-01

Full Text Available Utilization of lignocellulosic materials for the production of value-added chemicals or biofuels generally requires a pretreatment process to overcome the recalcitrance of the plant biomass for further enzymatic hydrolysis and fermentation stages. Two of the most employed pretreatment processes are the ones that used dilute acid (DA and alkaline (AL catalyst providing specific effects on the physicochemical structure of the biomass such as high xylan and lignin removal for DA and AL, respectively. Another important effect that need to be studied is the use of a high solids pretreatment (≥15% since offers many advantaged over lower solids loadings, including increased sugar and ethanol concentrations (in combination with a high solids saccharification which will be reflected in lower capital costs, however this data is currently limited. In this study, several variables such as catalyst loading, retention time and solids loading, were studied using Response Surface Methodology (RSM based on a factorial Central Composite Design (CCD of DA and AL pretreatment on agave bagasse using a range of solids from 3 to 30% (w/w to obtain optimal process conditions for each pretreatment. Subsequently enzymatic hydrolysis was performed using Novozymes Cellic CTec2 and HTec2 presented as total reducing sugar (TRS yield. Pretreated biomass

Solid-phase extraction of cobalt(II) from lithium chloride solutions using a poly(vinyl chloride)-based polymer inclusion membrane with Aliquat 336 as the carrier.

Science.gov (United States)

Kagaya, Shigehiro; Cattrall, Robert W; Kolev, Spas D

2011-01-01

The extraction of cobalt(II) from solutions containing various concentrations of lithium chloride, hydrochloric acid, and mixtures of lithium chloride plus hydrochloric acid is reported using a poly(vinyl chloride) (PVC)-based polymer inclusion membrane (PIM) containing 40% (w/w) Aliquat 336 as a carrier. The extraction from lithium chloride solutions and mixtures with hydrochloric acid is shown to be more effective than extraction from hydrochloric acid solutions alone. The solution concentrations giving the highest amounts of extraction are 7 mol L(-1) for lithium chloride and 8 mol L(-1) lithium chloride plus 1 mol L(-1) hydrochloric acid for mixed solutions. Cobalt(II) is easily stripped from the membrane using deionized water. The cobalt(II) species extracted into the membrane are CoCl(4)(2-) for lithium chloride solutions and HCoCl(4)(-) for mixed solutions; these form ion-pairs with Aliquat 336. It is also shown that both lithium chloride and hydrochloric acid are extracted by the PIM and suppress the extraction of cobalt(II) by forming ion-pairs in the membrane (i.e. R(3)MeN(+)·HCl(2)(-) for hydrochloric acid and R(3)MeN(+)·LiCl(2)(-) for lithium chloride). 2011 © The Japan Society for Analytical Chemistry

Evaluation of xylitol production using corncob hemicellulosic hydrolysate by combining tetrabutylammonium hydroxide extraction with dilute acid hydrolysis.

Science.gov (United States)

Jia, Honghua; Shao, Tingting; Zhong, Chao; Li, Hengxiang; Jiang, Min; Zhou, Hua; Wei, Ping

2016-10-20

In this paper, we produced hemicellulosic hydrolysate from corncob by tetrabutylammonium hydroxide (TBAH) extraction and dilute acid hydrolysis combined, further evaluating the feasibility of the resultant corncob hemicellulosic hydrolysate used in xylitol production by Candida tropicalis. Optimized conditions for corncob hemicellulose extraction by TBAH was obtained via response surface methodology: time of 90min, temperature of 60°C, liquid/solid ratio of 12 (v/w), and TBAH concentration of 55%, resulting in a hemicellulose extraction of 80.07% under these conditions. The FT-IR spectrum of the extracted corncob hemicellulose is consistent with that of birchwood hemicellulose and exhibits specific absorbance of hemicelluloses at 1380, 1168, 1050, and 900cm(-1). In addition, we found that C. tropicalis can ferment the resulting corncob hemicellulosic hydrolysate with pH adjustment and activated charcoal treatment leading to a high xylitol yield and productivity of 0.77g/g and 2.45g/(Lh), respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Facile synthesis of improved room temperature gas sensing properties of TiO2 nanostructures: Effect of acid treatment

CSIR Research Space (South Africa)

Tshabalala, Zamaswazi P

2016-03-01

Full Text Available TiO2 nanoparticles were synthesized via a simple hydrothermal method in a sodium hydroxide (NaOH) aqueous solution and washed with distilled water and different concentrations of hydrochloric acid which acted as the morphological...

Process Design Report for Wood Feedstock: Lignocellulosic Biomass to Ethanol Process Desing and Economics Utilizing Co-Current Dilute Acid Prehydrolysis and Enzymatic Hydrolysis Current and Futuristic Scenarios

Energy Technology Data Exchange (ETDEWEB)

Wooley, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ruth, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sheehan, John [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibsen, Kelly [National Renewable Energy Lab. (NREL), Golden, CO (United States); Majdeski, Henry [Delta-T Corporation, Lexington, KY (United States); Galves, Adrian [Delta-T Corporation, Lexington, KY (United States)

1999-07-01

The National Renewable Energy Laboratory (NREL) has undertaken a complete review and update of the process design and economic model for the biomass-to-ethanol process based on co-current dilute acid prehydrolysis, along with simultaneous saccharification (enzymatic) and co-fermentation. The process design includes the core technologies being researched by the U.S. Department of Energy (DOE): prehydrolysis, simultaneous saccharification and co-fermentation, and cellulase enzyme production.

Industrial ecotoxicology "acid rain".

Science.gov (United States)

Astolfi, E; Gotelli, C; Higa, J

1986-01-01

The acid rain phenomenon was studied in the province of Cordoba, Argentina. This study, based on a previously outlined framework, determined the anthropogenic origin of the low pH due to the presence of industrial hydrochloric acid wastage. This industrial ecotoxicological phenomenon seriously affected the forest wealth, causing a great defoliation of trees and shrubs, with a lower effect on crops. A survey on its effects on human beings has not been carried out, but considering the corrosion caused to different metals and its denouncing biocide effect on plants and animals, we should expect to find some kind of harm to the health of the workers involved or others engaged in farming, and even to those who are far away from the polluting agent.

Missense mutation in exon 2 of SLC36A1 responsible for champagne dilution in horses.

Directory of Open Access Journals (Sweden)

Deborah Cook

2008-09-01

Full Text Available Champagne coat color in horses is controlled by a single, autosomal-dominant gene (CH. The phenotype produced by this gene is valued by many horse breeders, but can be difficult to distinguish from the effect produced by the Cream coat color dilution gene (CR. Three sires and their families segregating for CH were tested by genome scanning with microsatellite markers. The CH gene was mapped within a 6 cM region on horse chromosome 14 (LOD = 11.74 for theta = 0.00. Four candidate genes were identified within the region, namely SPARC [Secreted protein, acidic, cysteine-rich (osteonectin], SLC36A1 (Solute Carrier 36 family A1, SLC36A2 (Solute Carrier 36 family A2, and SLC36A3 (Solute Carrier 36 family A3. SLC36A3 was not expressed in skin tissue and therefore not considered further. The other three genes were sequenced in homozygotes for CH and homozygotes for the absence of the dilution allele (ch. SLC36A1 had a nucleotide substitution in exon 2 for horses with the champagne phenotype, which resulted in a transition from a threonine amino acid to an arginine amino acid (T63R. The association of the single nucleotide polymorphism (SNP with the champagne dilution phenotype was complete, as determined by the presence of the nucleotide variant among all 85 horses with the champagne dilution phenotype and its absence among all 97 horses without the champagne phenotype. This is the first description of a phenotype associated with the SLC36A1 gene.

Oxic limestone drains for treatment of dilute, acidic mine drainage

Science.gov (United States)

Cravotta, Charles A.

1998-01-01

Limestone treatment systems can be effective for remediation of acidic mine drainage (AMD) that contains moderate concentrations of dissolved O2 , Fe3+ , or A13+ (1‐5 mg‐L‐1 ). Samples of water and limestone were collected periodically for 1 year at inflow, outflow, and intermediate points within underground, oxic limestone drains (OLDs) in Pennsylvania to evaluate the transport of dissolved metals and the effect of pH and Fe‐ and Al‐hydrolysis products on the rate of limestone dissolution. The influent was acidic and relatively dilute (pH 1 mg‐L‐1 ) but was near neutral (pH = 6.2‐7.0); Fe and Al decreased to less than 5% of influent concentrations. As pH increased near the inflow, hydrous Fe and Al oxides precipitated in the OLDs. The hydrous oxides, nominally Fe(OH)3 and AI(OH)3, were visible as loosely bound, orange‐yellow coatings on limestone near the inflow. As time elapsed, Fe(OH)3 and AI(OH)3 particles were transported downflow. During the first 6 months of the experiment, Mn 2+ was transported conservatively through the OLDs; however, during the second 6 months, concentrations of Mn in effluent decreased by about 50% relative to influent. The accumulation of hydrous oxides and elevated pH (>5) in the downflow part of the OLDs promoted sorption and coprecipitation of Mn as indicated by its enrichment relative to Fe in hydrous‐oxide particles and coatings on limestone. Despite thick (~1 mm) hydrous‐oxide coatings on limestone near the inflow, CaCO3 dissolution was more rapid near the inflow than at downflow points within the OLD where the limestone was not coated. The rate of limestone dissolution decreased with increased residence time, pH, and concentrations of Ca2+ and HCO3‐ and decreased PCO2. The following overall reaction shows alkalinity as an ultimate product of the iron hydrolysis reaction in an OLD:Fe2+ + 0.25 O2 +CaCO3 + 2.5 H2O --> Fe(OH)3 + 2 Ca2+ + 2 HCO3-where 2 moles of CaCO3 dissolve for each mole of Fe(OH)3 produced

Use of Gelidium amansii as a promising resource for bioethanol: a practical approach for continuous dilute-acid hydrolysis and fermentation.

Science.gov (United States)

Park, Jeong-Hoon; Hong, Ji-Yeon; Jang, Hyun Chul; Oh, Seung Geun; Kim, Sang-Hyoun; Yoon, Jeong-Jun; Kim, Yong Jin

2012-03-01

A facile continuous method for dilute-acid hydrolysis of the representative red seaweed species, Gelidium amansii was developed and its hydrolysate was subsequently evaluated for fermentability. In the hydrolysis step, the hydrolysates obtained from a batch reactor and a continuous reactor were systematically compared based on fermentable sugar yield and inhibitor formation. There are many advantages to the continuous hydrolysis process. For example, the low melting point of the agar component in G. amansii facilitates improved raw material fluidity in the continuous reactor. In addition, the hydrolysate obtained from the continuous process delivered a high sugar and low inhibitor concentration, thereby leading to both high yield and high final ethanol titer in the fermentation process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Impact of laminar flow velocity of different acids on enamel calcium loss.

Science.gov (United States)

Attin, T; Becker, K; Wiegand, A; Tauböck, T T; Wegehaupt, F J

2013-03-01

The aim of the study was to evaluate the impact of flow velocity under laminar flow conditions of different acidic solutions on enamel erosion. A total of 240 bovine enamel specimens were prepared and allocated to 30 groups (n = 8 each). Samples of 18 groups were superfused in a flow chamber system with laminar flow behavior using 1 ml of citric acid or hydrochloric acid (HCl) of pH 2.0, 2.6 or 3.0. Flow rates in the sample chamber were adjusted to 10, 60 or 100 μl/min. To simulate turbulent flow behavior, samples of six groups were immersed in 1 ml of the respective solution, which was vortexed (15 min, 600 rpm). For simulating non-agitated conditions, specimens of the remaining six groups were immersed in 1 ml of the respective solution without stirring. Calcium in the solutions, released from the enamel samples, was determined using Arsenazo III method. For acidic solutions of pH 2.6 and 3.0, erosive potential of citric acid was equivalent to that of HCl at a flow of 100 μl/min. The same observation was made for the samples subjected to turbulent conditions at pH 3. At all other conditions, citric acid induced a significantly higher calcium loss than HCl. It is concluded that under slow laminar flow conditions, flow rate variations lead to higher erosive impact of citric acid compared to hydrochloric acid at pH 2.0, but not at pH ≥ 2.6 and increasing laminar flow or turbulent conditions. Erosive enamel dissolution under laminar flow conditions is a complex issue influenced by flow rate and acidic substrate.

Phytanic acid alpha-oxidation: accumulation of 2-hydroxyphytanic acid and absence of 2-oxophytanic acid in plasma from patients with peroxisomal disorders

NARCIS (Netherlands)

ten Brink, H. J.; Schor, D. S.; Kok, R. M.; Poll-The, B. T.; Wanders, R. J.; Jakobs, C.

1992-01-01

A stable isotope dilution method was developed for the measurement of 2-hydroxyphytanic acid and 2-oxophytanic acid in plasma. In plasma from healthy individuals and from patients with Refsum's disease, 2-hydroxyphytanic acid was found at levels less than 0.2 mumol/l, whereas the acid accumulated in

PRODUCTION OF TRIFLUOROACETIC ACID COMPOUNDS

Science.gov (United States)

Haworth, W.N.; Stacey, M.

1949-08-30

A process is described for the preparation of trifluoroacetic acid. Acetone vapor diluted wlth nitrogen and fluorine also diluted with nltrogen are fed separately at a temperature of about 210 deg C into a reaction vessel containing a catalyst mass selected from-the group consisting of silver and gold. The temperature in the reaction vessel is maintained in the range of 200 deg to 250 deg C. The reaction product, trifluoroacetyl fluoride, is absorbed in aqueous alkali solution. Trifluoroacetic acid is recovered from the solution by acidification wlth an acid such as sulfuric followed by steam distillation.

Performance and techno-economic assessment of several solid-liquid separation technologies for processing dilute-acid pretreated corn stover.

Science.gov (United States)

Sievers, David A; Tao, Ling; Schell, Daniel J

2014-09-01

Solid-liquid separation of pretreated lignocellulosic biomass slurries is a critical unit operation employed in several different processes for production of fuels and chemicals. An effective separation process achieves good recovery of solute (sugars) and efficient dewatering of the biomass slurry. Dilute acid pretreated corn stover slurries were subjected to pressure and vacuum filtration and basket centrifugation to evaluate the technical and economic merits of these technologies. Experimental performance results were used to perform detailed process simulations and economic analysis using a 2000 tonne/day biorefinery model to determine differences between the various filtration methods and their process settings. The filtration processes were able to successfully separate pretreated slurries into liquor and solid fractions with estimated sugar recoveries of at least 95% using a cake washing process. A continuous vacuum belt filter produced the most favorable process economics. Copyright © 2014 Elsevier Ltd. All rights reserved.

A hydrometallurgical process for the recovery of terbium from fluorescent lamps: Experimental design, optimization of acid leaching process and process analysis.

Science.gov (United States)

Innocenzi, Valentina; Ippolito, Nicolò Maria; De Michelis, Ida; Medici, Franco; Vegliò, Francesco

2016-12-15

Terbium and rare earths recovery from fluorescent powders of exhausted lamps by acid leaching with hydrochloric acid was the objective of this study. In order to investigate the factors affecting leaching a series of experiments was performed in according to a full factorial plan with four variables and two levels (4 2 ). The factors studied were temperature, concentration of acid, pulp density and leaching time. Experimental conditions of terbium dissolution were optimized by statistical analysis. The results showed that temperature and pulp density were significant with a positive and negative effect, respectively. The empirical mathematical model deducted by experimental data demonstrated that terbium content was completely dissolved under the following conditions: 90 °C, 2 M hydrochloric acid and 5% of pulp density; while when the pulp density was 15% an extraction of 83% could be obtained at 90 °C and 5 M hydrochloric acid. Finally a flow sheet for the recovery of rare earth elements was proposed. The process was tested and simulated by commercial software for the chemical processes. The mass balance of the process was calculated: from 1 ton of initial powder it was possible to obtain around 160 kg of a concentrate of rare earths having a purity of 99%. The main rare earths elements in the final product was yttrium oxide (86.43%) following by cerium oxide (4.11%), lanthanum oxide (3.18%), europium oxide (3.08%) and terbium oxide (2.20%). The estimated total recovery of the rare earths elements was around 70% for yttrium and europium and 80% for the other rare earths. Copyright © 2016 Elsevier Ltd. All rights reserved.

One-step pretreatment of yellow poplar biomass using peracetic acid to enhance enzymatic digestibility.

Science.gov (United States)

Lee, Hyeong Rae; Kazlauskas, Romas J; Park, Tai Hyun

2017-09-22

Pretreatment of biomass with dilute acid requires high temperatures of >160 °C to remove xylan and does not remove lignin. Here we report that the addition of peracetic acid, a strong oxidant, to mild dilute acid pretreatment reduces the temperature requirement to only 120 °C. Pretreatment of yellow poplar with peracetic acid (300 mM, 2.3 wt%) and dilute sulfuric acid (100 mM, 1.0 wt%) at 120 °C for 5 min removed 85.7% of the xylan and 90.4% of the lignin leaving a solid consisting of 75.6% glucan, 6.0% xylan and 4.7% lignin. Low enzyme loadings of 5 FPU/g glucan and 10 pNPGU/g glucan converted this solid to glucose with an 84.0% yield. This amount of glucose was 2.5 times higher than with dilute acid-pretreated solid and 13.8 times higher than with untreated yellow poplar. Thus, the addition of peracetic acid, easily generated from acetic acid and hydrogen peroxide, dramatically increases the effectiveness of dilute acid pretreatment of biomass.

Determination of natural uranium in urine ({sup 233}U); Dosage de l'uranium dans l'urine ({sup 233}U)

Energy Technology Data Exchange (ETDEWEB)

Jeanmaire, L; Jammet, H [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

A procedure for the quantitative analysis of uranium in urine is described. The residue obtained by mineralization is dissolved in diluted hydrochloric acid. Uranium is separated by fixation on a permutit 50 column, elution with 0,2 M oxalic acid and electrodeposition on nickel. Uranium is then measured by {alpha} counting. It is thus possible to detect less than 1 pico-curie of uranium in the sample. (author) [French] Cet article decrit une technique de dosage de l'uranium dans l'urine. Apres mineralisation, le residu est dissous dans l'acide chlorhydrique dilue. L'uranium est separe par fixation, sur une colonne de permutite 50, elution au moyen d'acide oxalique 0,2 M et depot electrolytique sur nickel. La mesure faite par comptage {alpha} permet de detecter moins de 1 picocurie d'uranium dans l'echantillon. (auteur)

Radiation degradation and the consequent decrease in the efficacy of some dilute chemical decontaminant formulations

Energy Technology Data Exchange (ETDEWEB)

Kamal Kishore; Dey, G.R.; Naik, D.B.; Moorthy, P.N. [Applied Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai-400 085 (India)

1998-12-31

Constituents of dilute chemical decontaminant formulations such as ascorbic acid, EDTA, picolinic acid (PA) and 2,6-pyridine dicarboxylic acid (PDCA), also known as dipicolinic acid, are highly reactive with primary species produced from water radiolysis. Picolinic acid and PDCA however, are less sensitive to radiation dose due to their aromatic nature. They also help in protecting ascorbic acid when in a mixture. The efficacy for dissolution of magnetite was found to reduce drastically on irradiation in the case of EDTA/oxalic acid/citric acid while it was unaffected in the case of picolinic acid/ascorbic acid. In the case of EDTA/ascorbic acid/citric acid or PDCA/ascorbic acid formulations, there was only a marginal effect of radiation on the efficacy of the formulations. (author)

Effect of pretreatment severity on accumulation of major degradation products from dilute acid pretreated corn stover and subsequent inhibition of enzymatic hydrolysis of cellulose.

Science.gov (United States)

Um, Byung-Hwan; van Walsum, G Peter

2012-09-01

The concept of reaction severity, which combines residence time and temperature, is often used in the pulp and paper and biorefining industries. The influence of corn stover pretreatment severity on yield of sugar and major degradation products and subsequent effects on enzymatic cellulose hydrolysis was investigated. The pretreatment residence time and temperature, combined into the severity factor (Log R(o)), were varied with constant acid concentration. With increasing severity, increasing concentrations of furfural and 5-hydroxymethylfurfural (5-HMF) coincided with decreasing yields of oligosaccharides. With further increase in severity factor, the concentrations of furans decreased, while the formation of formic acid and lactic acid increased. For example, from severity 3.87 to 4.32, xylose decreased from 6.39 to 5.26 mg/mL, while furfural increased from 1.04 to 1.33 mg/mL; as the severity was further increased to 4.42, furfural diminished to 1.23 mg/mL as formate rose from 0.62 to 1.83 mg/mL. The effects of dilute acid hydrolyzate, acetic acid, and lignin, in particular, on enzymatic hydrolysis were investigated with a rapid microassay method. The microplate method gave considerable time and cost savings compared to the traditional assay protocol, and it is applicable to a broad range of lignocellulosic substrates.

Effect of strong acids on red mud structural and fluoride adsorption properties.

Science.gov (United States)

Liang, Wentao; Couperthwaite, Sara J; Kaur, Gurkiran; Yan, Cheng; Johnstone, Dean W; Millar, Graeme J

2014-06-01

The removal of fluoride using red mud has been improved by acidifying red mud with hydrochloric, nitric and sulphuric acid. The acidification of red mud causes sodalite and cancrinite phases to dissociate, confirmed by the release of sodium and aluminium into solution as well as the disappearance of sodalite bands and peaks in infrared and X-ray diffraction data. The dissolution of these mineral phases increases the amount of available iron and aluminium oxide/hydroxide sites that are accessible for the adsorption of fluoride. However, concentrated acids have a negative effect on adsorption due to the dissolution of these iron and aluminium oxide/hydroxide sites. The removal of fluoride is dependent on the charge of iron and aluminium oxide/hydroxides on the surface of red mud. Acidifying red mud with hydrochloric, nitric and sulphuric acid resulted in surface sites of the form ≡SOH2(+) and ≡SOH. Optimum removal is obtained when the majority of surface sites are in the form ≡SOH2(+) as the substitution of a fluoride ion does not cause a significant increase in pH. This investigation shows the importance of having a low and consistent pH for the removal of fluoride from aqueous solutions using red mud. Copyright © 2014 Elsevier Inc. All rights reserved.

Accurate determination and certification of bromine in plastic by isotope dilution inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Ohata, Masaki; Miura, Tsutomu

2014-01-01

Highlights: • Accurate analytical method of Br in plastic was studied by isotope dilution ICPMS. • A microwave acid digestion using quartz vessel was suitable for Br analysis. • Sample dilution by NH 3 solution could remove memory effect for ICPMS measurement. • The analytical result of the ID-ICPMS showed consistency with that of INAA. • The ID-ICPMS developed could apply to certification of Br in candidate plastic CRM. - Abstract: The accurate analytical method of bromine (Br) in plastic was developed by an isotope dilution inductively coupled plasma mass spectrometry (ID-ICPMS). The figures of merit of microwave acid digestion procedures using polytetrafluoroethylene (PTFE) or quartz vessels were studied and the latter one was suitable for Br analysis since its material was free from Br contamination. The sample dilution procedures using Milli-Q water or ammonium (NH 3 ) solution were also studied to remove memory effect for ICPMS measurement. Although severe memory effect was observed on Milli-Q water dilution, NH 3 solution could remove it successfully. The accuracy of the ID-ICPMS was validated by a certified reference material (CRM) as well as the comparison with the analytical result obtained by an instrumental neutron activation analysis (INAA) as different analytical method. From these results, the ID-ICPMS developed in the present study could be evaluated as accurate analytical method of Br in plastic materials and it could apply to certification of Br in candidate plastic CRM with respect to such regulations related to RoHS (restriction of the use of hazardous substances in electrical and electronics equipment) directive

Energy-dispersive X-ray fluorescence analysis of traces of heavy metals (Mn, Fe, Co, Ni, Cu, Zn, Ta, Pb, U) in mineral waters after separation on the cellulose-exchanger Hyphan

International Nuclear Information System (INIS)

Burba, P.; Lieser, K.H.

1979-01-01

Trace elements in mineral water are separated in small columns on the cellulose-exchanger Hyphan, eluted by diluted hydrochloric acid, bound on 100 mg of Hyphan by shaking and determined by energy-dispersive X-ray fluorescence. The following heavy metals can be analysed quantitatively if present in water in concentrations >= 1 ppb: Mn, Fe, Co, Ni, Cu, Zn, Ta, Pb and U. Several commercial mineral waters, a sodium chloride spring and seawater were analyzed for trace elements. The results obtained by X-ray fluorescence and by atomic absorption agree within the limits of error. (orig.) [de

Acid activation of natural clays aiming their application in adsorption

International Nuclear Information System (INIS)

Silva, M.M. da; Sousa, A.K.F. de; Lima, W.S.; Vasconcelos, P.N.M. de; Rodrigues, M. G.F.

2012-01-01

Clays of smectite type have wide application in industrial, mainly due to their adsorption properties. However, it is necessary to subject them to chemical treatments to optimize their potential. This study aimed to analyze the effects of acid activation on the clay Brasgel fresh. In the acid activation was used concentrated hydrochloric acid at different concentrations (3M, 4.5 M and 6 M) at a temperature of 70 ° C for 30 minutes. The samples fresh and activated technique were characterized by X-ray Diffraction (XRD). The results show that the properties of clay after activation are improved, it could be used as adsorbents in the treatment of wastewater. (author)

Synthesis of racemic, R- and S-[1-11C]-β-hydroxybutyric acid

International Nuclear Information System (INIS)

Thorell, J.-O.; Stone-Elander, S.; Karolinska Hospital and Inst., Stockholm; Koenig, W.A.; Halldin, C.; Widen, L.

1991-01-01

Racemic, R- and S-β-hydroxybutyric acid were labelled with 11 C in the carboxylic position by a two-step stereospecific synthesis starting with carrier-added [ 11 C]cyanide and R/S, R- or S-propylene oxide. Hydrolysis of the intermediate nitrile with hydrochloric acid gave racemic [1- 11 C]-β-hydroxybutyric acid and R- or S-[1- 11 C]-β-hydroxybutyric acid with an enantiomeric excess of 87-97%. The total synthesis time (including HPLC purification) was 45-50 min from end of trapping. The isolated decay-corrected radiochemical yield was 20-30% based on [ 11 C]cyanide. The radiochemical purity of the products was > 99%]. (author)

Exploring the Ideal Gas Law through a Quantitative Gasometric Analysis of Nitrogen Produced by the Reaction of Sodium Nitrite with Sulfamic Acid

Science.gov (United States)

Yu, Anne

2010-01-01

The gasometric analysis of nitrogen produced in a reaction between sodium nitrite, NaNO[superscript 2], and sulfamic acid, H(NH[superscript 2])SO[superscript 3], provides an alternative to more common general chemistry experiments used to study the ideal gas law, such as the experiment in which magnesium is reacted with hydrochloric acid. This…

Third phase formation in organic solutions in the extraction of mono-acids by tertiary trialcoyl-amines diluted in very slightly polar organic solvents

International Nuclear Information System (INIS)

Robaglia, Michele

1973-01-01

The phenomena of third phase formation which can occur during the extraction of an acid with a tertiary amine diluted in a low polarity diluent are studied. In the first part a system including water (TnOA - C 6 H 12 - HCl - H 2 O) is compared with an anhydrous system (TnOA - C 6 H 12 - HCl - N 2 ). There are two kinds of gaps. One during amine salification, another one during the extraction of excess acid. The important part of the water content of the organic phase is demonstrated. The presence of water enhances the gaps. The polar water molecules are dissolved inside the tri-octylamine salt micelles. The heavy phase is formed by aggregates, the light phase represents the solubility of the non soluble species in the medium. In the second part are studied the influence of some parameters (like nature of diluent, acid, amine and temperature) on the gaps formation and on the extraction of excess acid and water. In every cases the part played by water remains the same. Finally some comparisons are made between tertiary systems and binary systems which formed them. The binary systems were studied by the mean of crystallization curves. (author) [fr

Growing Chlorella vulgaris in Photobioreactor by Continuous Process Using Concentrated Desalination: Effect of Dilution Rate on Biochemical Composition

Directory of Open Access Journals (Sweden)

Ângelo Paggi Matos

2014-01-01

Full Text Available Desalination wastewater, which contains large amount of salt waste, might lead to severely environmental pollution. This study evaluated the effect of dilution rate (0.1≤D≤0.3 day−1 on microalgal biomass productivity, lipid content, and fatty acid profile under steady-state condition of Chlorella vulgaris supplemented with concentrated desalination. Continuous culture was conducted for 55 days. Results show that the biomass productivity (Px varied from 57 to 126 mg L−1 d−1 (dry mass when the dilution rate ranged from 0.1 to 0.3 day−1. At lowest dilution rate (D=0.1 day−1, the continuous culture regime ensured the highest values of maximum biomass concentration (Xm=570±20 mL−1 and protein content (52%. Biomass lipid content was an increasing function of D. The most abundant fatty acids were the palmitic (25.3±0.6% at D=0.1 day−1 and the gamma-linolenic acid (23.5±0.1% at D=0.3 day−1 ones. These fatty acids present 14 to 18 carbons in the carbon chain, being mainly saturated and polyunsaturated, respectively. Overall, the results show that continuous culture is a powerful tool to investigate the cell growth kinetics and physiological behaviors of the algae growing on desalination wastewater.

Overall process considerations for using dilute acid cellulose hydrolysis technology to produce ethanol from biomass

International Nuclear Information System (INIS)

Elander, R.; Ibsen, K.; Hayward, T.; Nagle, N.; Torget, R.

1997-01-01

Recent advances in reactors, designed for the dilute acid thermochemical treatment of biomass, have resulted in the development of process alternatives in which both cellulose and hemicellulose are hydrolyzed to soluble sugars in high yields. The optimal extent of cellulose hydrolysis will depend on both the performance and economics of the thermochemical treatment operation, and on subsequent unit operations in the bioethanol production process. Examples of subsequent unit operation interactions include the extent to which cellulase enzymes are used to hydrolyze any remaining cellulose, kinetics and conditions of a largely soluble mixed sugar cofermentation, and the extent to which removal of compounds that inhabit fermenting microorganisms is required. In addition, a number of process operation and economic considerations affect the ultimate economic viability of this type of biomass hydrolysis process. These considerations include reactor design issues to accommodate the kinetic parameters of the various hydrolysis and sugar degradation reactions, liquid volume requirements to achieve acceptable sugar yields, sugar concentrations that result from such a process and their impact on subsequent fermentation volumes and ethanol recovery operations, potential co-product opportunities that result from solubilized lignin, and process steam requirements. Several potential whole-process configurations are presented and key process and economic issues for each are discussed. (author)

Study of corrosion susceptibility of stainless steel-304 and stainless steel-316 under mechanical stress in diluted boiling nitric acid with chlorides

International Nuclear Information System (INIS)

Desjardins, D.; Puiggali, M.; El Kheloui, A.; Petit, M.C.; Clement, C.; Berge, J.P.

1991-01-01

A detailed study of corrosion of stressed 304 and 316 stainless steels in boiling solutions of diluted nitric acid in presence of chloride is presented. After a chemical study of the electrolyte, the different kinds of corrosion observed are represented on HNO 3 concentration - Cl - concentration diagrams. A more fundamental study based on several electrochemical techniques (forward scan and return potentiodynamic curves, potentiokinetic curves with different scan rates, sample depassivation by rapid straining under potentiostatic control) is carried out. The results allow to confirm the observations and to explain them in terms of competition between anodic dissolution, depassivation, repassivation processes with a precise analyze of the role of the solution and of the mechanical stress [fr

Optimization of dilute sulfuric acid pretreatment to maximize combined sugar yield from sugarcane bagasse for ethanol production.

Science.gov (United States)

Benjamin, Y; Cheng, H; Görgens, J F

2014-01-01

Increasing fermentable sugar yields per gram of biomass depends strongly on optimal selection of varieties and optimization of pretreatment conditions. In this study, dilute acid pretreatment of bagasse from six varieties of sugarcane was investigated in connection with enzymatic hydrolysis for maximum combined sugar yield (CSY). The CSY from the varieties were also compared with the results from industrial bagasse. The results revealed considerable differences in CSY between the varieties. Up to 22.7 % differences in CSY at the optimal conditions was observed. The combined sugar yield difference between the best performing variety and the industrial bagasse was 34.1 %. High ratio of carbohydrates to lignin and low ash content favored the release of sugar from the substrates. At mild pretreatment conditions, the differences in bioconversion efficiency between varieties were greater than at severe condition. This observation suggests that under less severe conditions the glucose recovery was largely determined by chemical composition of biomass. The results from this study support the possibility of increasing sugar yields or improving the conversion efficiency when pretreatment optimization is performed on varieties with improved properties.

Effects of chopping, and soaking in water, hydrochloric acidic and calcium hydroxide solutions on the nutritional value of Acacia villosa for goats

Energy Technology Data Exchange (ETDEWEB)

Wina, E. [Research Institute for Animal Production, Bogor (Indonesia)]. E-mail: winabudi@yahoo.com; Tangendjaja, B.; Susana, I.W.R. [Research Institute for Animal Production, Bogor (Indonesia)

2005-08-19

Acacia villosa, a thornless shrub legume, has potential as a feed supplement for ruminants if anti-nutritional factors, especially tannins, can be overcome. The effects of chopping and soaking the leaves on the amounts of tannin in the extracting solution and that left in the recovered leaves were studied. The tannin and non-tannin phenolics were solubilized in the extracting solution and the amount was increased with the soaking time. Soaking in calcium hydroxide solution, hydrochloric acid or water removed 41-76% of tannin and total phenolics removed from the recovered leaves. Soaking of the leaves also removed fermentable materials and reduced the gas production. In the first of two digestibility experiments, three groups of goats received one of these diets, those were: (1) sugar cane tops: unsoaked Acacia leaves (7:3), (2) sugar cane tops: water soaked Acacia leaves (7:3) and (3) sugar cane tops: water soaked Acacia leaves (7:3) + 100 g/day of cassava flour. Live weight of goats was measured every 2 weeks and a large increase in average daily gain was obtained for goats fed diet containing water soaked leaves and cassava flour (71 g/day) compared to those fed diet containing unsoaked leaves and water soaked leaves (38.9 and 44.7 g/day, respectively) (P < 0.05). In the second digestibility experiment, the three diets were: (1) sugar cane tops: unsoaked Acacia (7:3), (2) sugar cane tops water soaked Acacia (7:3), (3) sugar cane tops: calcium hydroxide soaked Acacia (7:3). A supplement of 100 g/day of cassava flour was added to each of these three diets. In both digestibility experiments, soaking improved intake and digestibility of Acacia leaves, and cassava flour increased the intake, but when all the diets contained cassava flour, there was no significant difference (P > 0.05) found in intake or digestibility between unsoaked and soaked leaves. In conclusion, soaking reduced tannin in Acacia leaves, improved digestibility and intake of Acacia leaves. In the

Accurate determination and certification of bromine in plastic by isotope dilution inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Ohata, Masaki, E-mail: m-oohata@aist.go.jp; Miura, Tsutomu

2014-07-21

Highlights: • Accurate analytical method of Br in plastic was studied by isotope dilution ICPMS. • A microwave acid digestion using quartz vessel was suitable for Br analysis. • Sample dilution by NH{sub 3} solution could remove memory effect for ICPMS measurement. • The analytical result of the ID-ICPMS showed consistency with that of INAA. • The ID-ICPMS developed could apply to certification of Br in candidate plastic CRM. - Abstract: The accurate analytical method of bromine (Br) in plastic was developed by an isotope dilution inductively coupled plasma mass spectrometry (ID-ICPMS). The figures of merit of microwave acid digestion procedures using polytetrafluoroethylene (PTFE) or quartz vessels were studied and the latter one was suitable for Br analysis since its material was free from Br contamination. The sample dilution procedures using Milli-Q water or ammonium (NH{sub 3}) solution were also studied to remove memory effect for ICPMS measurement. Although severe memory effect was observed on Milli-Q water dilution, NH{sub 3} solution could remove it successfully. The accuracy of the ID-ICPMS was validated by a certified reference material (CRM) as well as the comparison with the analytical result obtained by an instrumental neutron activation analysis (INAA) as different analytical method. From these results, the ID-ICPMS developed in the present study could be evaluated as accurate analytical method of Br in plastic materials and it could apply to certification of Br in candidate plastic CRM with respect to such regulations related to RoHS (restriction of the use of hazardous substances in electrical and electronics equipment) directive.

Acid dip for dosemeter

International Nuclear Information System (INIS)

Stewart, J.C.; McWhan, A.F.

1982-01-01

Background signal in a PTFE based dosemeter caused by impurities in the PTFE and in the active component such as lithium fluoride is substantially reduced by treating the dosemeter with acid. The optimum treatment involves use of hydrofluoric acid at room temperature for approximately one minute, followed by thorough washing with methanol, and finally drying. This treatment is best applied after the original manufacture of the dosemeters. It may also be applied to existing dosemeters after they have been in use for some time. The treatment produces a permanent effect in reducing both the light induced signal and the non-light induced signal. The process may be applied to all types of dosemeter manufactured from PTFE or other plastics or resins which are able to resist brief exposure to acid. The treatment works particularly well with dosemeters based on PTFE and lithium fluoride. It is also applicable to dosemeters based on calcium sulphate, lithium borate and magnesium borate. Acids which may be used include hydrofluoric, hydrochloric, nitric, phosphoric and sulphuric. (author)

Differential Mobility-Mass Spectrometry Double Spike Isotope Dilution Study of Release of β-Methylaminoalanine and Proteinogenic Amino Acids during Biological Sample Hydrolysis.

Science.gov (United States)

Beach, Daniel G; Kerrin, Elliott S; Giddings, Sabrina D; Quilliam, Michael A; McCarron, Pearse

2018-01-08

The non-protein amino acid β-methylamino-L-alanine (BMAA) has been linked to neurodegenerative disease and reported throughout the environment. Proposed mechanisms of bioaccumulation, trophic transfer and chronic toxicity of BMAA rely on the hypothesis of protein misincorporation. Poorly selective methods for BMAA analysis have led to controversy. Here, a recently reported highly selective method for BMAA quantitation using hydrophilic interaction liquid chromatography-differential mobility spectrometry-tandem mass spectrometry (HILIC-DMS-MS/MS) is expanded to include proteinogenic amino acids from hydrolyzed biological samples. For BMAA quantitation, we present a double spiking isotope dilution approach using D 3 -BMAA and 13 C 15 N 2 -BMAA. These methods were applied to study release of BMAA during acid hydrolysis under a variety of conditions, revealing that the majority of BMAA can be extracted along with only a small proportion of protein. A time course hydrolysis of BMAA from mussel tissue was carried out to assess the recovery of BMAA during sample preparation. The majority of BMAA measured by typical methods was released before a significant proportion of protein was hydrolyzed. Little change was observed in protein hydrolysis beyond typical hydrolysis times but the concentration of BMAA increased linearly. These findings demonstrate protein misincorporation is not the predominant form of BMAA in cycad and shellfish.

Acid Rain

Science.gov (United States)

Bricker, Owen P.; Rice, Karen C.

1995-01-01

Although acid rain is fading as a political issue in the United States and funds for research in this area have largely disappeared, the acidity of rain in the Eastern United States has not changed significantly over the last decade, and it continues to be a serious environmental problem. Acid deposition (commonly called acid rain) is a term applied to all forms of atmospheric deposition of acidic substances - rain, snow, fog, acidic dry particulates, aerosols, and acid-forming gases. Water in the atmosphere reacts with certain atmospheric gases to become acidic. For example, water reacts with carbon dioxide in the atmosphere to produce a solution with a pH of about 5.6. Gases that produce acids in the presence of water in the atmosphere include carbon dioxide (which converts to carbonic acid), oxides of sulfur and nitrogen (which convert to sulfuric and nitric acids}, and hydrogen chloride (which converts to hydrochloric acid). These acid-producing gases are released to the atmosphere through natural processes, such as volcanic emissions, lightning, forest fires, and decay of organic matter. Accordingly, precipitation is slightly acidic, with a pH of 5.0 to 5.7 even in undeveloped areas. In industrialized areas, most of the acid-producing gases are released to the atmosphere from burning fossil fuels. Major emitters of acid-producing gases include power plants, industrial operations, and motor vehicles. Acid-producing gases can be transported through the atmosphere for hundreds of miles before being converted to acids and deposited as acid rain. Because acids tend to build up in the atmosphere between storms, the most acidic rain falls at the beginning of a storm, and as the rain continues, the acids "wash out" of the atmosphere.

Impaired acid neutralization in the duodenum in pancreatic insufficiency.

Science.gov (United States)

Dutta, S K; Russell, R M; Iber, F L

1979-10-01

The influence of severe exocrine pancreatic disease on the acid-neutralizing capacity of the duodenum was studied in five patients with pancreatic insufficiency (PI) and six control subjects using duodenal perfusion-marker technique. Hydrochloric acid (0.1 N containing 1% PEG) was infused at constant rates (1.2, 4.5 and 7.0 ml/min) into the duodenum just distal to the duodenal bulb. Samples were aspirated from the tip of the duodenal perfusion tube located at the ligament of Treitz. All samples were analyzed for volume, pH, titrable acidity, PEG and [14C]PEG (gastric marker) determination. Patients with PI demonstrated significantly diminished ability to neutralize various acid loads as compared to controls who virtually completely neutralized acid loads in the range of maximal gastric acid secretion. Exogenous secretin did not significantly improve percent acid neutralized in PI. These data clearly indicate that patients with PI have significantly impaired ability to neutralize even small loads of acid in the duodenum.

A rapid microwave induced synthesis of [carboxyl-14C]-nicotinic acid (vitamin B3) and [carbonyl-14C]-nicotinamide using K14CN

International Nuclear Information System (INIS)

Ravi, S.; Mathew, K.M.; Sivaprasad, N.

2008-01-01

Microwave assisted direct aromatic substitution of 3-bromopyridine with K 14 CN as the cyanide source and catalytic amount of tetrabutylammonium bromide afforded [3- 14 C]-cyanopyridine 3 in 90% yield. Microwave assisted hydrolysis of 3 with a mixture of concentrated hydrochloric acid and propionic acid afforded [carboxyl- 14 C]-nicotinic acid in 95% yield whereas microwave assisted hydrolysis of 3 with a mixture of concentrated sulfuric acid and propionic acid afforded [carbonyl- 14 C]-nicotinamide in 85% yield. (author)

Effects of the Addictives on Etching Characteristics of Aluminum Foil

Energy Technology Data Exchange (ETDEWEB)

Kim, S.K.; Jang, J.M.; Chi, C.S. [Kookmin University, Seoul (Korea); Shin, D.C. [Sungnam Polytechnic, Sungnam (Korea); Lee, J.H.; Oh, H.J. [Hanseo University, Seosan (Korea)

2001-01-01

The effects of additives in the HCI etching solution on etching behaviors of aluminium foil as dielectric film for electrolytic capacitors were investigated. The etch pits formed in 1M hydrochloric acid containing ethylene glycol as an additive contain more fine and homogeneous etch tunnels compared to thoese in 1 M hydrochloric acid only, which led to the increase in the effective internal surface area of aluminum foil. After anodizing of aluminum foil etched in etching solutions, the LCR meter results have shown that the capacitance of dielectric film etched in hydrochloric acid with ethylene glycol was increased remarkably compared to that etched in hydrochloric acid only. (author). 21 refs., 10 figs.

Process Design and Economics for the Conversion of Lignocellulosic Biomass to Hydrocarbons: Dilute-Acid and Enzymatic Deconstruction of Biomass to Sugars and Catalytic Conversion of Sugars to Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Davis, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tao, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Scarlata, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tan, E. C. D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ross, J. [Harris Group Inc., New York, NY (United States); Lukas, J. [Harris Group Inc., New York, NY (United States); Sexton, D. [Harris Group Inc., New York, NY (United States)

2015-03-01

This report describes one potential conversion process to hydrocarbon products by way of catalytic conversion of lignocellulosic-derived hydrolysate. This model leverages expertise established over time in biomass deconstruction and process integration research at NREL, while adding in new technology areas for sugar purification and catalysis. The overarching process design converts biomass to die die diesel- and naphtha-range fuels using dilute-acid pretreatment, enzymatic saccharification, purifications, and catalytic conversion focused on deoxygenating and oligomerizing biomass hydrolysates.

Kinetic study of ion exchange in phosphoric acid chelating resin

International Nuclear Information System (INIS)

Brikci-Nigassa, Mounir; Hamouche, Hafida

1995-11-01

Uranium may be recovered as a by product of wet phosphoric acid using a method based on specific ion exchange resins. These resins called chelates contain amino-phosphonic functional groups. The resin studied in this work is a purolite S-940; uranium may be loaded on this resin from 30% P2O5 phosphoric acid in its reduced state. The influence of different parameters on the successive steps of the process have been studied in batch experiments: uranium reduction, loading and oxydation. Uranium may be eluted with ammonium carbonate and the resin regeneration may be done with hydrochloric acid.Ferric ions reduce the effective resin capacity considerably and inert fixation conditions are proposed to enhance uranium loading

Acid tolerance in Salmonella typhimurium induced by culturing in the presence of organic acids at different growth temperatures.

Science.gov (United States)

Alvarez-Ordóñez, Avelino; Fernández, Ana; Bernardo, Ana; López, Mercedes

2010-02-01

The influence of growth temperature and acidification of the culture medium up to pH 4.25 with acetic, citric, lactic and hydrochloric acids on the growth and subsequent acid resistance at pH 3.0 of Salmonella typhimurium CECT 443 was studied. The minimum pH value which allowed for S. typhimurium growth within the temperature range of 25-37 degrees C was 4.5 when the pH was reduced using citric and hydrochloric acids, and 5.4 and 6.4 when lactic acid and acetic acid were used, respectively. At high (45 degrees C) or low (10 degrees C) temperatures, the growth pH boundary was increased about 1 pH unit. The growth temperature markedly modified the acid resistance of the resulting cells. In all cases, D-values were lower for cells grown at 10 degrees C and significantly increased with increasing growth temperature up to 37 degrees C, at which D-values obtained were up to 10 times higher. Cells grown at 45 degrees C showed D-values similar to those found for cells grown at 25 degrees C. The growth of cells in acidified media, regardless of the pH value, caused an increase in their acid resistance at the four incubation temperatures, although the magnitude of the Acid Tolerance Response (ATR) observed depended on the growth temperature. Acid adapted cultures at 10 degrees C showed D-values ranging from 5.75 to 6.91 min, which turned out to be about 2 times higher than those corresponding to non-acid adapted cultures, while higher temperatures induced an increase in D-values of at least 3.5 times. Another finding was that, while at 10 and 45 degrees C no significant differences among the effect of the different acids tested in inducing an ATR were observed, when cells were grown at 25 and 37 degrees C citric acid generally turned out to be the acid which induced the strongest ATR. Results obtained in this study show that growth temperature is an important factor affecting S. typhimurium acid resistance and could contribute to find new strategies based on intelligent

A Cumulative Spore Killing Approach: Synergistic Sporicidal Activity of Dilute Peracetic Acid and Ethanol at Low pH Against Clostridium difficile and Bacillus subtilis Spores.

Science.gov (United States)

Nerandzic, Michelle M; Sankar C, Thriveen; Setlow, Peter; Donskey, Curtis J

2016-01-01

Background.  Alcohol-based hand sanitizers are the primary method of hand hygiene in healthcare settings, but they lack activity against bacterial spores produced by pathogens such as Clostridium difficile and Bacillus anthracis. We previously demonstrated that acidification of ethanol induced rapid sporicidal activity, resulting in ethanol formulations with pH 1.5-2 that were as effective as soap and water washing in reducing levels of C difficile spores on hands. We hypothesized that the addition of dilute peracetic acid (PAA) to acidified ethanol would enhance sporicidal activity while allowing elevation of the pH to a level likely to be well tolerated on skin (ie, >3). Methods.  We tested the efficacy of acidified ethanol solutions alone or in combination with PAA against C difficile and Bacillus subtilis spores in vitro and against nontoxigenic C difficile spores on hands of volunteers. Results.  Acidification of ethanol induced rapid sporicidal activity against C difficile and to a lesser extent B subtilis. The addition of dilute PAA to acidified ethanol resulted in synergistic enhancement of sporicidal activity in a dose-dependent fashion in vitro. On hands, the addition of 1200-2000 ppm PAA enhanced the effectiveness of acidified ethanol formulations, resulting in formulations with pH >3 that were as effective as soap and water washing. Conclusions.  Acidification and the addition of dilute PAA induced rapid sporicidal activity in ethanol. Our findings suggest that it may be feasible to develop effective sporicidal ethanol formulations that are safe and tolerable on skin.

Enzymatic saccharification of liquid hot water and dilute sulfuric acid pretreated oil palm empty fruit bunch and sugarcane bagasse

Science.gov (United States)

Risanto, L.; Fitria; Fajriutami, T.; Hermiati, E.

2018-03-01

Oil palm empty fruit bunch (OPEFB) and sugarcane bagasse (SB) are potential feedstocks for the production of bioethanol. In this study OPEFB and SB were pretreated by liquid hot water and dilute sulfuric acid (3% H2SO4), and continued with enzymatic saccharification. Heating treatment for both methods was conducted in an autoclave at 121 °C for 1 hr. The saccharification was performed up to 72 hours with cellulase enzyme loading of 10, 20, and 30 FPU per g biomass. Results showed that OPEFB and SB pretreated with H2SO4 produced higher reducing sugars than those pretreated by liquid hot water. Higher enzyme loading also resulted in higher reducing sugars. Reducing sugars obtained from enzymatic saccharification of OPEFB were higher than those obtained from SB. The highest total reducing sugars (50.48 g/100 g biomass) was obtained from OPEFB pretreated with 3% H2SO4 at enzyme loading of 30 FPU per g biomass.

Effect of Aging Temperature on Corrosion Behavior of Sintered 17-4 PH Stainless Steel in Dilute Sulfuric Acid Solution

Science.gov (United States)

Szewczyk-Nykiel, Aneta; Kazior, Jan

2017-07-01

The general corrosion behavior of sintered 17-4 PH stainless steel processed under different processing conditions in dilute sulfuric acid solution at 25 °C was studied by open-circuit potential measurement and potentiodynamic polarization technique. The corrosion resistance was evaluated based on electrochemical parameters, such as polarization resistance, corrosion potential, corrosion current density as well as corrosion rate. The results showed that the precipitation-hardening treatment could significantly improve the corrosion resistance of the sintered 17-4 PH stainless steel in studied environment. As far as the influence of aging temperature on corrosion behavior of the sintered 17-4 PH stainless steel is concerned, polarization resistance and corrosion rate are reduced with increasing aging temperature from 480 up to 500 °C regardless of the temperature of solution treatment. It can be concluded that the highest corrosion resistance in 0.5 M H2SO4 solution exhibits 17-4 PH after solution treatment at 1040 °C followed by aging at 480 °C.

Studies of the structure of insulin fibrils by Fourier transform infrared (FTIR) spectroscopy and electron microscopy.

Science.gov (United States)

Nielsen, L; Frokjaer, S; Carpenter, J F; Brange, J

2001-01-01

Fibril formation (aggregation) of insulin was investigated in acid media by visual inspection, transmission electron microscopy (TEM), and Fourier transform infrared (FTIR) spectroscopy. Insulin fibrillated faster in hydrochloric acid than in acetic acid at elevated temperatures, whereas the fibrillation tendencies were reversed at ambient temperatures. Electron micrographs showed that bovine insulin fibrils consisted of long fibers with a diameter of 5 to 10 nm and lengths of several microns. The fibrils appeared either as helical filaments (in hydrochloric acid) or arranged laterally in bundles (in acetic acid, NaCl). Freeze-thawing cycles broke the fibrils into shorter segments. FTIR spectroscopy showed that the native secondary structure of insulin was identical in hydrochloric acid and acetic acid, whereas the secondary structure of fibrils formed in hydrochloric acid was different from that formed in acetic acid. Fibrils of bovine insulin prepared by heating or agitating an acid solution of insulin showed an increased content of beta-sheet (mostly intermolecular) and a decrease in the intensity of the alpha-helix band. In hydrochloric acid, the frequencies of the beta-sheet bands depended on whether the fibrillation was induced by heating or agitation. This difference was not seen in acetic acid. Freeze-thawing cycles of the fibrils in hydrochloric acid caused an increase in the intensity of the band at 1635 cm(-1) concomitant with reduction of the band at 1622 cm(-1). The results showed that the structure of insulin fibrils is highly dependent on the composition of the acid media and on the treatment. Copyright 2001 Wiley-Liss Inc. and the American Pharmaceutical Association J Pharm Sci 90: 29-37, 2001

Distribution and origin of major and trace elements (particularly REE, U and Th) into labile and residual phases in an acid soil profile (Vosges Mountains, France)

Science.gov (United States)

Aubert, D.; Probst, A.; Stille, P.

2003-04-01

Physical and chemical weathering of rocks and minerals lead to soil formation and allow the removal of chemical elements from these systems to ground- or surface waters. But most of the time the determination of element concentrations in soils is not sufficient to estimate whether they are being accumulated or what is their ability to be released in the environment. Thus, the distribution and chemical binding for a given element is very important because it determines its mobility and potential bioavailability throughout a soil profile. Heavy metals and REE (Rare Earth Elements) are particularly of environmental concern because of their potential toxicity. For most of them, their chemical form strongly depends on the evolution of physico-chemical parameters like pH or redox conditions that will induce adsorption-desorption, complexation or co-precipitation phenomena in the material. The purpose of this study is to determine the distribution of several major and trace elements (especially REE, Th and U) in an acidic forested podzolic soil profile from the Vosges Mountains (France). To achieve this goal we use a 7 step sequential extraction procedure that allows determining precisely the origin and the behaviour of particular elements in the environment (Leleyter et al., 1999). In addition we performed leaching experiments using very dilute acetic and hydrochloric acid in order to establish the origin of REE in this soil. The results of the sequential extraction indicate that most of the metals, Th and U are mainly bound to Fe oxides. Organic matter appears also to be a great carrier of P, Ca, Fe and REE even if its content is very low in the deep horizons of the soil. Moreover, we show that in each soil horizon, middle REE (MREE) to heavy REE (HREE) are more labile than light REE (LREE). Leaching experiments using dilute acid solution further suggest that in the shallowest horizons REE largely derive from atmospheric deposition whereas at greater depth, weathering

The molecular properties of biochar carbon released in dilute acidic solution and its effects on maize seed germination.

Science.gov (United States)

Sun, Jingling; Drosos, Marios; Mazzei, Pierluigi; Savy, Davide; Todisco, Daniele; Vinci, Giovanni; Pan, Genxing; Piccolo, Alessandro

2017-01-15

It is not yet clear whether the carbon released from biochar in the soil solution stimulates biological activities. Soluble fractions (AQU) from wheat and maize biochars, whose molecular content was thoroughly characterized by FTIR, 13 C and 1 H NMR, and high-resolution ESI-IT-TOF-MS, were separated in dilute acidic solution to simulate soil rhizospheric conditions and their effects evaluated on maize seeds germination activity. Elongation of maize-seeds coleoptile was significantly promoted by maize biochar AQU, whereas it was inhibited by wheat biochar AQU. Both AQU fractions contained relatively small heterocyclic nitrogen compounds, whose structures were accounted by their spectroscopic properties. Point-of-Zero-Charge (PZC) values and van Krevelen plots of identified masses of soluble components suggested that the dissolved carbon from maize biochar behaved as humic-like supramolecular material capable to adhere to seedlings and deliver bioactive molecules. These findings contribute to understand the biostimulation potential of biochars from crop biomasses when applied in agricultural production. Copyright © 2016 Elsevier B.V. All rights reserved.

Acid in perchloroethylene scrubber solutions used in HTGR fuel preparation processes. Analytical chemistry studies

International Nuclear Information System (INIS)

Lee, D.A.

1979-02-01

Acids and corrosion products in used perchloroethylene scrubber solutions collected from HTGR fuel preparation processes have been analyzed by several analytical methods to determine the source and possible remedy of the corrosion caused by these solutions. Hydrochloric acid was found to be concentrated on the carbon particles suspended in perchloroethylene. Filtration of carbon from the scrubber solutions removed the acid corrosion source in the process equipment. Corrosion products chemisorbed on the carbon particles were identified. Filtered perchloroethylene from used scrubber solutions contained practically no acid. It is recommended that carbon particles be separated from the scrubber solutions immediately after the scrubbing process to remove the source of acid and that an inhibitor be used to prevent the hydrolysis of perchloroethylene and the formation of acids

Mixotrophic growth and biochemical analysis of Chlorella vulgaris cultivated with diluted monosodium glutamate wastewater.

Science.gov (United States)

Ji, Yan; Hu, Wenrong; Li, Xiuqing; Ma, Guixia; Song, Mingming; Pei, Haiyan

2014-01-01

Monosodium glutamate wastewater (MSGW) is a potential medium for microbial cultivation because of containing abundant organic nutrient. This paper seeks to evaluate the feasibility of growing Chlorella vulgaris with MSGW and assess the influence of MSGW concentration on the biomass productivity and biochemical compositions. The MSGW diluted in different concentrations was prepared for microalga cultivation. C. vulgaris growth was greatly promoted with MSGW compared with the inorganic BG11 medium. C. vulgaris obtained the maximum biomass concentration (1.02 g/L) and biomass productivity (61.47 mg/Ld) with 100-time diluted MSGW. The harvested biomass was rich in protein (36.01-50.64%) and low in lipid (13.47-25.4%) and carbohydrate (8.94-20.1%). The protein nutritional quality and unsaturated fatty acids content of algal increased significantly with diluted MSGW. These results indicated that the MSGW is a feasible alternative for mass cultivation of C. vulgaris. Copyright © 2013 Elsevier Ltd. All rights reserved.

Reactivities of acid and/or tetralin pretreated Wandoan coal for a Curie point flash pyrolysis; Sanzen shori, tetralin yobaimae shori Wandoan tan no kyusoku netsubunkai

Energy Technology Data Exchange (ETDEWEB)

Kishino, M.; Sakanishi, K.; Korai, Y.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-10-28

Discussions were given on effects of acid pretreatment and tetralin swelling in Wandoan coal on a Curie point flash pyrolysis (which used a Curie point pyrolyzer). Residue yield loss effects were obtained at 3.9% in hydrochloric acid pretreatment, and 6.2% in acetic acid pretreatment. The effects of tetralin swelling pretreatment were compared in the similar manner in terms of the residue yield loss. The effects were 4.0% in untreated coal, 2.0% in the hydrochloric acid pretreatment, and 0.6% in the acetic acid pretreatment. It is thought that components that can be activated by acetic acid have already been activated, but the remaining components would not be activated by tetralin. Average microporosity (area) in the remaining particle as a whole shows very little difference both in acetic acid pretreated coal and untreated coal. However, with the acetic acid pretreatment, pores smaller than 4{mu}m{sup 2} disappeared, and pores as large as 205 to 411{mu}m{sup 2} increased largely. This phenomenon was observed as an increase in foaming degree under microscopic observation, even if the average microporosity remains equal. Thermoplasticity of the coal increased, and so did volatilization reactivity as a result of the acetic acid pretreatment, resulting in appearance of a large number of large pores. 6 refs., 2 figs., 2 tabs.

Furfural production from fruit shells by acid-catalyzed hydrolysis

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A. [Selcuk Univ., Konya (Turkey). Dept. of Chemical Engineering

2006-01-21

Pentosans are hydrolyzed to pentoses by dilute mineral acid hydrolysis. The main source of pentosans is hemicelluloses. Furfural can be produced by the acid hydrolysis of pentosan from fruit shells such as hazelnut, sunflower, walnut, and almond of agricultural wastes. Further dehydration reactions of the pentoses yield furfural. The hydrolysis of each shell sample was carried out in dilute sulfuric acid (0.05 to 0.200 mol/l), at high temperature (450-525 K), and short reaction times (from 30 to 600 s). (author)

Influence of solid loading on D-xylose production through dilute sulphuric acid hydrolysis of olive stones

Directory of Open Access Journals (Sweden)

Cuevas, M.

2015-09-01

Full Text Available The selective hydrolysis of hemicellulose from olive stones was attempted in order to achieve a maximum D-xylose yield. For this aim, batch hydrolysis was conducted under different operating conditions of temperature, acid concentration and solid loading. Firstly, distilled water, sulphuric acid and nitric acid were assessed as hydrolytic agents at different temperatures (200, 205, 210 and 220 °C and at a fixed acid concentration (0.025 M. Sulphuric acid and 200 °C were selected for the subsequent dilute acid hydrolysis optimization based on the obtained D-xylose yields. The combined influence of solid loading (from 29.3 to 170.7 g olive stones into 300 mL acid solution and sulphuric acid concentration (0.006–0.034 M on the release of D-xylose was then estimated by response surface methodology. According to a statistical analysis, both parameters had significant interaction effects on D-xylose production. The results illustrated that the higher the solid loading, the higher the required acid concentration. The decrease in the solid/liquid ratio in the reactor had a positive effect on D-xylose extraction and on the amount of acid used. The optimum solid loading and sulphuric acid concentration were determined to be 50 g (solid/liquid ratio 1/6 and 0.016 M, respectively. Under these conditions, the predicted D-xylose yield (expressed as g of sugar per 100 g of dry matter fed was 20.4 (87.2% of maximum attainable.Se ha desarrollado una hidrólisis selectiva de la fracción hemicelulósica del hueso de aceituna con el fin de obtener el máximo rendimiento de D-xilosa. Para ello las hidrólisis se llevaron a cabo en un reactor discontinuo a distintas condiciones de temperatura, concentración de ácido y carga de sólidos. En primer lugar se evaluó la capacidad hidrolítica del agua destilada y de los ácidos nítrico y sulfúrico a distintas temperaturas (200, 205, 210 y 220°C manteniendo fija la concentración de ácido (0,025 M. A partir de

Amperometric estimation of La3+ and Ce3+ with cupferron using d.m.e

International Nuclear Information System (INIS)

Pitre, K.S.; Lavale, S.C.

1982-01-01

Cupferron has been employed as a reagent for the amperometric titrations of La 3+ and Ce 3+ in very dilute solution using d.m.e. Hydrochloric acid (pH=2.75) has been used as supporting electrolyte. These titrations revealed cupferron to metal ratio of 1:1. Titrations are not hampered by the presence of a fairly large amount of Li + , Na + , K + , Mg 3+ , Zn 3+ , Al 3+ , Cl - , Br - , I - , NO 3 - , NO 2 - , CH 2 COO - and ClO 4 - ions. Furthermore, micro and ultramicro quantities of La 3+ and Ce 2+ have been successfully determined with an error of less than +- 0.70%. (author)

Reduction of trace quantities of chromium(VI by strong acids

Directory of Open Access Journals (Sweden)

Pezzin Sérgio H

2004-01-01

Full Text Available The chemical behavior of Cr(VI at low concentrations (10-4 to 10-7 mol L-1 in several strong acids was studied using high specific activity 51Cr(VI as a tracer. The speciation of the products from these systems was carried out by ion exchange chromatography with stepwise elution. The results show that trace quantities of Cr(VI, monitored by means of radiochromium (51Cr, are reduced in the presence of mineral acids such as perchloric, hydrochloric, hydrofluoric, sulfuric, nitric and trifluoromethanesulfonic acids, even in the absence of conventional reducing agents, producing different measureable Cr(III species, depending on the acid anion. Detailed studies of the reduction of low concentrations of Cr(VI with nitric acid have shown that the relative rate of reduction increases as the concentration of the acid increases or as the concentration of the Cr(VI decreases.

Preliminary Study on the Dissolutions of Ce, Nd, Y and La from Mineral Cassiterite by Acid and Alkaline Leaching

Science.gov (United States)

Firdiyono, F.; Andriyah, L.; Aini, F. N.; Arini, T.; Lalasari, L. H.

2018-03-01

Rare Earth Metal is a rare element that its availability in nature is very small. In Indonesia, the potential of rare earth metals is generally found as the associated mineral in major commodities, especially gold and alluvial tin. These associated minerals can be processed using a particular technology so that the result is a by-product that can increase the added value of the mineral. This purpose of this research was to investigate the dissolution of Cerium (Ce), Neodymium (Nd), Yttrium (Y) and Lanthanum (La) from mineral cassiterite by leaching process using dilute hydrochloric acid (HCl), sulfate acid (H2SO4) and sodium hydroxide (NaOH). Firstly, cassiterite was grinded to -100 mesh of particle size and characterized by X-Ray Diffraction (XRD) and X-Ray Fluorescence (XRF) techniques. Secondly, 10 gram of cassiterite was leached in 100 ml solution of 3.26 N HCl, H2SO4 and NaOH at variation leaching time of 2, 4, 6, 24 and 48 hours in atmospheric conditions. The products were then filtered to separate filtrate and residue of cassiterite. Finally, to investigate the dissolution of Ce, La, Nd and Y, filtrate from dissolved cassiterite was analyzed by Induced Coupled Plasma-Optical Emission Spectrometry (ICP-OES), while to know the chemical composition of cassiterite leached by dilute HCl, H2SO4 and NaOH, residue products of cassiterite was characterized by XRF analysis. The result of ICP-OES analysis showed the dissolution of Ce element higher than Nd, Y and La elements for leaching cassiterite using HCl, H2SO4 and NaOH. The increase of leaching time was accompanied by the rise in the amount of dissolved elements from cassiterite. The result of XRF analysis showed the chemistry composition of Ce, Nd, Y and La elements on residue decreased insignificantly from chemistry composition of cassiterite (raw mineral) in all conditions. However, the dissolution of Ce, La, Nd and Y was insignificant in all conditions.

Rapid anion exchange separation of fermium with mineral acid-methyl alcohol mixed media

International Nuclear Information System (INIS)

Usuda, S.; Shinohara, N.; Ichikawa, S.; Suzuki, T.

1987-01-01

Anion exchange separation of 250 Fm (30 m) synthesized by the 12 C+ 242 Pu and 16 O+ 238 U reactions was investigated with mineral acid-methyl alcohol mixed media at elevated temperature. Fermium was chromatographically separated from the other transplutonium elements, the target materials and an Al catcher foil by anion exchange with mixtures of nitric acid and methyl alcohol. By use of the mixed media of hydrochloric acid and methyl alcohol, Fm together with Cf was separated from Al, Am, Cm, Pu, U and from major fission products. The separation systems are suitable for rapid separation and immediate alpha-counting source preparation of Fm. (author) 22 refs.; 4 figs

Photo-crosslinked hyaluronic acid coated upconverting nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Mrazek, Jiri, E-mail: jiri.mrazek@contipro.com; Kettou, Sofiane; Matuska, Vit; Svozil, Vit; Huerta-Angeles, Gloria; Pospisilova, Martina; Nesporova, Kristina; Velebny, Vladimir [Contipro a. s. (Czech Republic)

2017-02-15

Hyaluronic acid (HA)-coated inorganic nanoparticles display enhanced interaction with the CD44 receptors which are overexpressed in many types of cancer cells. Here, we describe a modification of core-shell β-NaY{sub 0.80}Yb{sub 0.18}Er{sub 0.02}F{sub 4}@NaYF{sub 4} nanoparticles (UCNP) by HA derivative bearing photo-reactive groups. UCNP capped with oleic acid were firstly transferred to aqueous phase by an improved protocol using hydrochloric acid or lactic acid treatment. Subsequently, HA bearing furanacryloyl moieties (HA-FU) was adsorbed on the nanoparticle surface and crosslinked by UV irradiation. The crosslinking resulted in stable HA coating, and no polymer desorption was observed. As-prepared UCNP@HA-FU show a hydrodynamic diameter of about 180 nm and are colloidally stable in water and cell culture media. The cellular uptake by normal human fibroblasts and MDA MB-231 cancer cell line was investigated by upconversion luminescence imaging.

Separation of metal ions by anion exchange in mixtures of hydrochloric acid and hydrofluoric acid

International Nuclear Information System (INIS)

Faris, J.P.

1978-12-01

Distribution coefficients were determined for the adsorption of more than 40 elements on anion-exchange resins from mixtures of HCl (0.1 to 12M) and HF (0.1-8M). Two resins, Dowex 1 x 10, 200 to 400 mesh and Dowex 1 x 4, 100 to 200 mesh, were used. Distribution coefficients were also determined for the adsorption of many elements on both resins from 0.1 to 12M HCl and 0.1 to 12M HF. Anion exchange in the presence of HF was found useful for separating impurities from various materials for their subsequent determination, and specific procedures used in our spectrochemical laboratory for this purpose are outlined. The results of a literature search on the use of anion exchange in hydrofluoric acid and fluoride-containing media are presented in an extensive bibliography. 404 references, 9 tables

In vitro thermal profile suitability assessment of acids and bases for thermochemical ablation: underlying principles.

Science.gov (United States)

Freeman, Laura A; Anwer, Bilal; Brady, Ryan P; Smith, Benjamin C; Edelman, Theresa L; Misselt, Andrew J; Cressman, Erik N K

2010-03-01

To measure and compare temperature changes in a recently developed gel phantom for thermochemical ablation as a function of reagent strength and concentration with several acids and bases. Aliquots (0.5-1 mL) of hydrochloric acid or acetic acid and sodium hydroxide or aqueous ammonia were injected for 5 seconds into a hydrophobic gel phantom. Stepwise increments in concentration were used to survey the temperature changes caused by these reactions. Injections were performed in triplicate, measured with a thermocouple probe, and plotted as functions of concentration and time. Maximum temperatures were reached almost immediately in all cases, reaching 75 degrees C-110 degrees C at the higher concentrations. The highest temperatures were seen with hydrochloric acid and either base. More concentrated solutions of sodium hydroxide tended to mix incompletely, such that experiments at 9 M and higher were difficult to perform consistently. Higher concentrations for any reagent resulted in higher temperatures. Stronger acid and base combinations resulted in higher temperatures versus weak acid and base combinations at the same concentration. Maximum temperatures obtained are in a range known to cause tissue coagulation, and all combinations tested therefore appeared suitable for further investigation in thermochemical ablation. Because of the loss of the reaction chamber shape at higher concentrations of stronger agents, the phantom does not allow complete characterization under these circumstances. Adequate mixing of reagents to maximize heating potential and avoid systemic exposure to unreacted acid and base must be addressed if the method is to be safely employed in tissues. In addition, understanding factors that control lesion shape in a more realistic tissue model will be critical. Copyright 2010 SIR. Published by Elsevier Inc. All rights reserved.

Investigation of adsorption and inhibitive effect of acid red GRE (183 dye on the corrosion of carbon steel in hydrochloric acid media

Directory of Open Access Journals (Sweden)

M. Abd El-raouf

2015-09-01

Full Text Available The adsorption and corrosion inhibitive effect of acid red GRE (183 dye on carbon steel alloy in 1 M HCl solutions was studied using various techniques. Results of weight loss, Tafel polarization measurements and electrochemical impedance spectroscopy (EIS techniques show that this compound has fairly good inhibiting properties for steel corrosion in acidic bath; with efficiency around 96% at a concentration of 50 ppm. The inhibition is of a mixed anodic–cathodic nature. Factors affecting the corrosion process have been calculated and discussed. Acid red GRE (183 dye was shown to be an inhibitor in the acidic corrosion. Inhibition efficiency increased with acid red GRE (183 dye concentration but decreased with rise in temperature, corrosion inhibition is attributed to the adsorption of acid red GRE (183 dye on the carbon steel surface via a physical adsorption mechanism. Langmuir isotherm is found to provide an accurate description of the adsorption behavior of the investigated azo compound. The nature of the protective film was investigated using SEM and EDX techniques.

Effect of a low-viscosity adhesive resin on the adhesion of metal brackets to enamel etched with hydrochloric or phosphoric acid combined with conventional adhesives.

Science.gov (United States)

Yetkiner, Enver; Ozcan, Mutlu; Wegehaupt, Florian Just; Wiegand, Annette; Eden, Ece; Attin, Thomas

2013-12-01

This study investigated the effect of a low-viscosity adhesive resin (Icon) applied after either hydrochloric (HCl) or phosphoric acid (H3PO4) on the adhesion of metal brackets to enamel. Failure types were analyzed. The crowns of bovine incisors (N = 20) were sectioned mesio-distally and inciso-gingivally, then randomly assigned to 4 groups according to the following protocols to receive mandibular incisor brackets: 1) H3PO4 (37%)+TransbondXT (3M UNITEK); 2) H3PO4 (37%)+Icon+TransbondXT; 3) HCl (15%)+Icon (DMG)+TransbondXT 4) HCl (15%)+Icon+Heliobond (Ivoclar Vivadent)+TransbondXT. Specimens were stored in distilled water at 37°C for 24 h and thermocycled (5000x, 5°C to 55°C). The shear bond strength (SBS) test was performed using a universal testing machine (1 mm/min). Failure types were classified according to the Adhesive Remnant Index (ARI). Contact angles of adhesive resins were measured (n = 5 per adhesive) on ceramic surfaces. No significant difference in SBS was observed, implying no difference between combinations of adhesive resins and etching agents (p = 0.712; ANOVA). The Weibull distribution presented significantly lower Weibull modulus (m) of group 3 (m = 2.97) compared to other groups (m = 5.2 to 6.6) (p group 1 (45.4 ± 7.9) > group 2 (44.2 ± 10.6) > group 3 (42.6 ± 15.5). While in groups 1, 3, and 4 exclusively an ARI score of 0 (no adhesive left on tooth) was observed, in group 2, only one specimen demonstrated score 1 (less than half of adhesive left on tooth). Contact angle measurements were as follows: Icon (25.86 ± 3.81 degrees), Heliobond (31.98 ± 3.17 degrees), TransbondXT (35 ± 2.21 degrees). Icon can be safely used with the conventional adhesives tested on surfaces etched with either HCl or H3PO4.

Dilution Refrigeration of Multi-Ton Cold Masses

CERN Document Server

Wikus, P; CERN. Geneva

2007-01-01

Dilution refrigeration is the only means to provide continuous cooling at temperatures below 250 mK. Future experiments featuring multi-ton cold masses require a new generation of dilution refrigeration systems, capable of providing a heat sink below 10 mK at cooling powers which exceed the performance of present systems considerably. This thesis presents some advances towards dilution refrigeration of multi-ton masses in this temperature range. A new method using numerical simulation to predict the cooling power of a dilution refrigerator of a given design has been developed in the framework of this thesis project. This method does not only allow to take into account the differences between an actual and an ideal continuous heat exchanger, but also to quantify the impact of an additional heat load on an intermediate section of the dilute stream. In addition, transient behavior can be simulated. The numerical model has been experimentally verified with a dilution refrigeration system which has been designed, ...

Adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution

International Nuclear Information System (INIS)

Tatsuya Suzuki

2013-01-01

The adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution were investigated. The adsorbed amounts of lanthanides and the degree of mutual separation of lanthanides increased with an increase in the concentration of lithium chloride in aqueous solution. The group separation of the trivalent actinides and lanthanides was observed. This separation phenomenon is similar in a hydrochloric acid solution. However, the adsorption behavior of lanthanides in lithium chloride is different from their behavior in a hydrochloric acid solution. This fact shows that the adsorption mechanisms of lanthanides in a lithium chloride aqueous solution and in a hydrochloric acid solution are different; the adsorption mechanisms are attributed to the ion exchange in a hydrochloric acid solution, and to the complex formation with pyridine group in a lithium chloride solution. (author)

Cleanex process: a versatile solvent extraction process for recovery and purification of lanthanides, americium, and curium

International Nuclear Information System (INIS)

Bigelow, J.E.; Collins, E.D.; King, L.J.

1979-01-01

At a concentration of 1 M in straight-chain hydrocarbon diluent, HDEHP will extract americium, curium, and other trivalent actinide and lanthanide elements from dilute acid or salt solutions. The solute is back-extracted with more concentrated acid, either nitric or hydrochloric. The process has been used in the continuous, countercurrent mode, but its greatest advantage arises in batch extractions where the excess acid can be titrated with NaOH to produce a final acidity of about 0.03 M. Under these conditions, 99% recovery can be achieved, usually in one stage. Cleanex was used on the 50-liter scale at the Transuranium Processing Plant at Oak Ridge for 12 years to provide a broad spectrum cleanup to transuranium elements before applying more sophisticated techniques for separating individual products. The process is also used routinely to recover excessive losses of curium and/or californium from plant waste streams. The solvent system is relatively resistant to radiation damage, being usable up to 200 W-h/liter

Effects of brief milling and acid treatment on two ordered and disordered kaolinite structures

Czech Academy of Sciences Publication Activity Database

Valášková, M.; Barabaszová, K.; Hundáková, M.; Ritz, M.; Plevová, Eva

2011-01-01

Roč. 54, č. 1 (2011), s. 70-76 ISSN 0169-1317 R&D Projects: GA ČR GA105/08/1398 Grant - others:GA ČR(CZ) GA205/09/0352 Institutional research plan: CEZ:AV0Z30860518 Keywords : kaolinite * milling * hydrochloric acid Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.474, year: 2011 http://www.sciencedirect.com/science/article/pii/S0169131711002675

Use of frontal analysis in ion exchange chromatography for the study of reactions of formation of complexes in solution. Application to hydrochloric complexes of nickel (II), cobalt (II) and copper (II)

International Nuclear Information System (INIS)

Tremillon, Bernard

1959-01-01

The ion exchanger column frontal analysis method provides a convenient way to study complex formation reactions when they are very unstable. It has the advantage of being much more sensitive and precise than the method (already used by other authors) of simple equilibrium between a solution and an ion exchanger. As an illustration of this method, the hydrochloric acid complexes NiCl + , CoCl + and CuCl + , have been studied, and their dissociation constants were determined (respectively 4.6 ± 0.1; 4.0 ± 0.1 and 2.5 ± 0.1, at an ionic strength substantially equal to 1.5). Reprint of a paper published in Bulletin de la Societe Chimique de France, 1958, p. 1483-1487 [fr

Cacotheline as an oxidimetric reagent. Determination of Sn(II), Cu(I), Ti(III), Fe(II), V(II) and V(III)

International Nuclear Information System (INIS)

Nemani Murty, K.; Yedluri Rao, P.; Geddada Chalam, K.

1982-01-01

Sn(II), Ti(III), Cu(I),Fe(II), V(III) and V(II) can be titrated potentiometrically with cacotheline in 1-4 M hydrochloric acid, 0.5-2 M hydrochloric acid, 0.5-1.5 M sulphuric acid in presence of 4 ml of 10% EDTA solution in a total volume of 50 ml, 9-10 M phosphoric acid, 4-8 M acetic acid and 3-8 M acetic acid respectively. Cacotheline can be used for the assay of tin plate and solder. The cacotheline undergoes a 2-electron reduction reaction. A cacotheline solution (0.005 M) in 0.02 M hydrochloric acid is fairly stable for several months. The conditional redox potentials of cacotheline have been determined in sulphuric, phosphoric and acetic acid medium. (Author)

Lactic acid demineralization of shrimp shell and chitosan synthesis

Directory of Open Access Journals (Sweden)

Alewo Opuada AMEH

2015-05-01

Full Text Available The use of lactic acid was compared to hydrochloric acid for shrimp shell demineralization in chitosan synthesis. Five different acid concentrations were considered for the study: 1.5M, 3.0M, 4.5M, 6.0M and 7.5M. After demineralization, the shrimp shell were deproteinized and subsequently deacetylated to produce chitosan using sodium hydroxide solution. The synthesized chitosan samples were characterized using solubility, FTIR, SEM, XRD and viscosity. The SEM, FTIR and XRD analysis indicated that chitosan was synthesized with a high degree of deacetylation (83.18±2.11 when lactic acid was used and 84.2±5.00 when HCl was used. The degree of deacetylation and the molecular weight of the chitosan samples were also estimated. ANOVA analysis (at 95% confidence interval indicated that acid type and concentration did not significantly affect the solubility, degree of deacetylation, viscosity and molecular weight of the chitosan within the range considered.

Quantification of transformation rates of soil amino sugars and amino acids by a novel isotope pool dilution approach via liquid chromatography/high resolution mass spectrometry (LC/HRMS)

Science.gov (United States)

Hu, Yuntao; Zheng, Qing; Noll, Lisa; Zhang, Shasha; Wanek, Wolfgang