WorldWideScience

Sample records for digital receiver technology

  1. Cryogenic analog-to-digital converters using spread spectrum technology for coherent receivers

    Science.gov (United States)

    Shiao, Yu-Shao Jerry; Chiueh, Tzihong; Hu, Robert

    2012-09-01

    We propose analog-to-digital converters (ADCs) using spread spectrum technology in cryogenic receivers or at warm room temperature for coherent receiver backend systems. As receiver signals are processed and stored digitally, ADCs play a critical role in backend read-out systems. To minimize signal distortion, the down-converted signals should be digitized without further transportation. However, digitizing the signals in or near receivers may cause radio frequency interference. We suggest that spread spectrum technology can reduce the interference significantly. Moreover, cryogenic ADCs at regulated temperature in receiver dewars may also increase the bandwidth usage and simplify the backend digital signal process with fewer temperature-dependant components. While industrial semiconductor technology continuously reduces transistor power consumption, low power high speed cryogenic ADCs may become a better solution for coherent receivers. To examine the performance of cooled ADCs, first, we design 4 bit 65 nm and 40 nm CMOS ADCs specifically at 10 K temperature, which commonly is the second stage temperature in dewars. While the development of 65 nm and 40 nm CMOS ADCs are still on-going, we estimate the ENOB is 2.4 at 10 GSPS, corresponding to the correlation efficiency, 0.87. The power consumption is less than 20 mW.

  2. Digital Receiver Phase Meter

    Science.gov (United States)

    Marcin, Martin; Abramovici, Alexander

    2008-01-01

    The software of a commercially available digital radio receiver has been modified to make the receiver function as a two-channel low-noise phase meter. This phase meter is a prototype in the continuing development of a phase meter for a system in which radiofrequency (RF) signals in the two channels would be outputs of a spaceborne heterodyne laser interferometer for detecting gravitational waves. The frequencies of the signals could include a common Doppler-shift component of as much as 15 MHz. The phase meter is required to measure the relative phases of the signals in the two channels at a sampling rate of 10 Hz at a root power spectral density digital receiver. The input RF signal is first fed to the input terminal of an analog-to-digital converter (ADC). To prevent aliasing errors in the ADC, the sampling rate must be at least twice the input signal frequency. The sampling rate of the ADC is governed by a sampling clock, which also drives a digital local oscillator (DLO), which is a direct digital frequency synthesizer. The DLO produces samples of sine and cosine signals at a programmed tuning frequency. The sine and cosine samples are mixed with (that is, multiplied by) the samples from the ADC, then low-pass filtered to obtain in-phase (I) and quadrature (Q) signal components. A digital signal processor (DSP) computes the ratio between the Q and I components, computes the phase of the RF signal (relative to that of the DLO signal) as the arctangent of this ratio, and then averages successive such phase values over a time interval specified by the user.

  3. Broadband direct RF digitization receivers

    CERN Document Server

    Jamin, Olivier

    2014-01-01

    This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains.  A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis.  Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm...

  4. Digital Sensor Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ted Quinn; Jerry Mauck; Richard Bockhorst; Ken Thomas

    2013-07-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy, reliability, availability, and maintainability. This report demonstrates these benefits in direct comparisons of digital and analog sensor applications. It also addresses the qualification issues that must be addressed in the application of digital sensor technology.

  5. Anatomy of a digital coherent receiver

    DEFF Research Database (Denmark)

    Borkowski, Robert; Zibar, Darko; Tafur Monroy, Idelfonso

    2014-01-01

    Digital coherent receivers have gained significant attention in the last decade. The reason for this is that coherent detection, along with digital signal processing (DSP) allows for substantial increase of the channel capacity by employing advanced detection techniques. In this paper, we first......, orthonormaliation, chromatic dispersion compensation/nonlinear compensation, resampling a nd timing recovery, polarization demultiplexing and equalization, frequency and phase recovery, digital demodulation. We also describe novel subsystems of a digital coherent receiver: modulation format recognition...

  6. Digital Signal Processor For GPS Receivers

    Science.gov (United States)

    Thomas, J. B.; Meehan, T. K.; Srinivasan, J. M.

    1989-01-01

    Three innovative components combined to produce all-digital signal processor with superior characteristics: outstanding accuracy, high-dynamics tracking, versatile integration times, lower loss-of-lock signal strengths, and infrequent cycle slips. Three components are digital chip advancer, digital carrier downconverter and code correlator, and digital tracking processor. All-digital signal processor intended for use in receivers of Global Positioning System (GPS) for geodesy, geodynamics, high-dynamics tracking, and ionospheric calibration.

  7. Digital Demodulator For Advanced Receiver

    Science.gov (United States)

    Sadr, Ramin; Hurd, William J.

    1990-01-01

    Complexity and cost reduced by new design for half-band filters. Digital demodulator designed for use in reception of phase- and amplitude-modulated digital signals of bandwidths up to 15 MHz on microwave carriers. System performs coherent demodulation in phase and in quadrature with carrier locked in phase to intermediate frequency of 10 MHz. Design suitable for fabrication in very-large-scale integrated circuitry. Principal innovative feature of demodulator is design of half-band digital low-pass filters that remove sum-frequency components.

  8. Efficient structures for wideband digital receiver

    Institute of Scientific and Technical Information of China (English)

    Wang Hong; Lu Youxin; Wang Xuegang; Wan Yonglun

    2006-01-01

    Digital receivers have become more and more popular in radar, communication, and electric warfare for the advantages compared with their analog counterparts. But conventional digital receivers have been generally considered impractical for bandwidth greater than several hundreds MHz. To extend receiver bandwidth, decrease data rate and save hardware resources, three novel structures are proposed. They decimate the data stream prior to mixing and filtering, then process the multiple decimated streams in parallel at a lower rate. Consequently it is feasible to realize wideband receivers on the current ASIC devices. A design example and corresponding simulation results are demonstrated to evaluate the proposed structures.

  9. 宽带数字通信接收技术研究%Study on receiving technology for wideband digital communication

    Institute of Scientific and Technical Information of China (English)

    苟亚男

    2012-01-01

    The wireless receiving technology for wideband digital communication is studied in this paper to solve the problem existing in multi-channel receiving system for the wideband digital communication. The multi-channel efficient model suitable for wireless receiving system for wideband digital communication is derived and given through the study of signal sampling theory. The model gets fewer orders of filter by the design of prototype filter with same filtering performance and reduces the resource occupation ratio of the system. The correctness of the model was verified by computer simulation. The model has less calculated amount,compared with traditional models,and is suitable for the engineering application.%为了解决宽带数字通信系统多信道同时接收问题,这里针对宽带无线数字通信接收技术展开了深入研究,在研究信号采样理论的基础上,推导并给出了一种适用于宽带无线数字通信接收系统的多通道信道化高效模型.该模型利用原型滤波器的设计,在保证了滤波性能的同时获得了较少的阶数,降低了资源占有率,计算机仿真验证了该模型的正确性.该模型和传统模型相比有较少的计算量,适合于工程化应用.

  10. Digital security technology simplified.

    Science.gov (United States)

    Scaglione, Bernard J

    2007-01-01

    Digital security technology is making great strides in replacing analog and other traditional security systems including CCTV card access, personal identification and alarm monitoring applications. Like any new technology, the author says, it is important to understand its benefits and limitations before purchasing and installing, to ensure its proper operation and effectiveness. This article is a primer for security directors on how digital technology works. It provides an understanding of the key components which make up the foundation for digital security systems, focusing on three key aspects of the digital security world: the security network, IP cameras and IP recorders.

  11. Digital Receiver for Laser Imaging Radar

    Institute of Scientific and Technical Information of China (English)

    WANG Wei Ran; SUN Bing

    2004-01-01

    With the extension of the application domains for laser imaging radar,it is necessary to find a new technical way to obtain high technical performance and adaptive ability.In this paper,A new concept of digital receiver of laser imaging radar system is presented.This digital receiver is defined as a time varying parameter receiver which possesses large dynamics region and time domain filter.The receiver's mode,component structure as well as every function of its processing are described.The results and laboratorial data show the feasibility of digital reception.Also,it can exploit the inherent nature of laser imaging radar to obtain high probability of detection.

  12. Digital Technology Entrepreneurship

    DEFF Research Database (Denmark)

    Giones, Ferran; Brem, Alexander

    2017-01-01

    Technology entrepreneurship is an established concept in academia. However, recent developments in the context of digital entrepreneurship call for revision and advance- ment. The multiple possible combinations of technology and entrepreneurship have res- ulted in a diversity of phenomena...... with significantly different characteristics and socio-economic impact. This article is focused on the identification and description of technology entrepreneurship in times of digitization. Based on current examples, we identify and describe characterizations of technology entrepreneurship, digital techno- logy...... entrepreneurship, and digital entrepreneurship. With this new delineation of terms, we would like to foster discussion between researchers, entrepreneurs, and policy makers on the impact of digitization on entrepreneurship, and set a future research agenda....

  13. Special design topics in digital wideband receivers

    CERN Document Server

    Tsui, James B Y

    2009-01-01

    Offering engineers a thorough examination of special, more advanced aspects of digital wideband receiver design, this practical book builds on fundamental resources on the topic, helping you gain a more comprehensive understanding of the subject. This in-depth volume presents a detailed look at a complete receiver design, including the encoder. Moreover, it discusses the detection of exotic signals and provides authoritative guidance on designing receivers used in electronic warfare. From frequency modulation and biphase shifting keys, to parameter encoders in electronic warfare receivers and

  14. Digital Actuator Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ken Thomas; Ted Quinn; Jerry Mauck; Richard Bockhorst

    2014-09-01

    There are significant developments underway in new types of actuators for power plant active components. Many of these make use of digital technology to provide a wide array of benefits in performance of the actuators and in reduced burden to maintain them. These new product offerings have gained considerable acceptance in use in process plants. In addition, they have been used in conventional power generation very successfully. This technology has been proven to deliver the benefits promised and substantiate the claims of improved performance. The nuclear industry has been reluctant to incorporate digital actuator technology into nuclear plant designs due to concerns due to a number of concerns. These could be summarized as cost, regulatory uncertainty, and a certain comfort factor with legacy analog technology. The replacement opportunity for these types of components represents a decision point for whether to invest in more modern technology that would provide superior operational and maintenance benefits. Yet, the application of digital technology has been problematic for the nuclear industry, due to qualification and regulatory issues. With some notable exceptions, the result has been a continuing reluctance to undertake the risks and uncertainties of implementing digital actuator technology when replacement opportunities present themselves. Rather, utilities would typically prefer to accept the performance limitations of the legacy analog actuator technologies to avoid impacts to project costs and schedules. The purpose of this report is to demonstrate that the benefits of digital actuator technology can be significant in terms of plant performance and that it is worthwhile to address the barriers currently holding back the widespread development and use of this technology. It addresses two important objectives in pursuit of the beneficial use of digital actuator technology for nuclear power plants: 1. To demonstrate the benefits of digital actuator

  15. Digital Sensor Technology

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Ken D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Quinn, Edward L. [Technology Resources, Dana Point, CA (United States); Mauck, Jerry L. [Technology Resources, Dana Point, CA (United States); Bockhorst, Richard M. [Technology Resources, Dana Point, CA (United States)

    2015-02-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy and reliability. This paper, which refers to a final report issued in 2013, demonstrates these benefits in direct comparisons of digital and analog sensor applications. Improved accuracy results from the superior operating characteristics of digital sensors. These include improvements in sensor accuracy and drift and other related parameters which reduce total loop uncertainty and thereby increase safety and operating margins. An example instrument loop uncertainty calculation for a pressure sensor application is presented to illustrate these improvements. This is a side-by-side comparison of the instrument loop uncertainty for both an analog and a digital sensor in the same pressure measurement application. Similarly, improved sensor reliability is illustrated with a sample calculation for determining the probability of failure on demand, an industry standard reliability measure. This looks at equivalent analog and digital temperature sensors to draw the comparison. The results confirm substantial reliability improvement with the digital sensor, due in large part to ability to continuously monitor the health of a digital sensor such that problems can be immediately identified and corrected. This greatly reduces the likelihood of a latent failure condition of the sensor at the time of a design basis event. Notwithstanding the benefits of digital sensors, there are certain qualification issues that are inherent with digital technology and these are described in the report. One major qualification impediment for digital sensor implementation is software common cause failure (SCCF).

  16. Synthesis of digital locomotive receiver of automatic locomotive signaling

    Directory of Open Access Journals (Sweden)

    K. V. Goncharov

    2013-02-01

    Full Text Available Purpose. Automatic locomotive signaling of continuous type with a numeric coding (ALSN has several disadvantages: a small number of signal indications, low noise stability, high inertia and low functional flexibility. Search for new and more advanced methods of signal processing for automatic locomotive signaling, synthesis of the noise proof digital locomotive receiver are essential. Methodology. The proposed algorithm of detection and identification locomotive signaling codes is based on the definition of mutual correlations of received oscillation and reference signals. For selecting threshold levels of decision element the following criterion has been formulated: the locomotive receiver should maximum set the correct solution for a given probability of dangerous errors. Findings. It has been found that the random nature of the ALSN signal amplitude does not affect the detection algorithm. However, the distribution law and numeric characteristics of signal amplitude affect the probability of errors, and should be considered when selecting a threshold levels According to obtained algorithm of detection and identification ALSN signals the digital locomotive receiver has been synthesized. It contains band pass filter, peak limiter, normalizing amplifier with automatic gain control circuit, analog to digital converter and digital signal processor. Originality. The ALSN system is improved by the way of the transfer of technical means to modern microelectronic element base, more perfect methods of detection and identification codes of locomotive signaling are applied. Practical value. Use of digital technology in the construction of the locomotive receiver ALSN will expand its functionality, will increase the noise immunity and operation stability of the locomotive signal system in conditions of various destabilizing factors.

  17. Chromatic Dispersion Estimation in Digital Coherent Receivers

    DEFF Research Database (Denmark)

    Soriano, Ruben Andres; Hauske, Fabian N.; Guerrero Gonzalez, Neil

    2011-01-01

    Polarization-diverse coherent demodulation allows to compensate large values of accumulated linear distortion by digital signal processing. In particular, in uncompensated links without optical dispersion compensation, the parameter of the residual chromatic dispersion (CD) is vital to set...

  18. Intermediate Frequency Digital Receiver Based on Multi-FPGA System

    Directory of Open Access Journals (Sweden)

    Chengchang Zhang

    2016-01-01

    Full Text Available Aiming at high-cost, large-size, and inflexibility problems of traditional analog intermediate frequency receiver in the aerospace telemetry, tracking, and command (TTC system, we have proposed a new intermediate frequency (IF digital receiver based on Multi-FPGA system in this paper. Digital beam forming (DBF is realized by coordinated rotation digital computer (CORDIC algorithm. An experimental prototype has been developed on a compact Multi-FPGA system with three FPGAs to receive 16 channels of IF digital signals. Our experimental results show that our proposed scheme is able to provide a great convenience for the design of IF digital receiver, which offers a valuable reference for real-time, low power, high density, and small size receiver design.

  19. Chromatic Dispersion Estimation in Digital Coherent Receivers

    DEFF Research Database (Denmark)

    Soriano, Ruben Andres; Hauske, Fabian N.; Guerrero Gonzalez, Neil;

    2011-01-01

    Polarization-diverse coherent demodulation allows to compensate large values of accumulated linear distortion by digital signal processing. In particular, in uncompensated links without optical dispersion compensation, the parameter of the residual chromatic dispersion (CD) is vital to set the ac...

  20. Art Education Technology: Digital Storytelling

    Science.gov (United States)

    Chung, Sheng Kuan

    2007-01-01

    The application of digital storytelling to art education is an interdisciplinary, inquiry-based, hands-on project that integrates the arts, education, local communities, technology, and storytelling. Through digital storytelling, students develop and apply multiliteracy skills, aesthetic sensitivities, and critical faculties to address greater…

  1. Digital terrestrial television broadcasting technology and system

    CERN Document Server

    2015-01-01

    Now under massive deployment worldwide, digital terrestrial television broadcasting (DTTB) offers one of the most attractive ways to deliver digital TV over the VHF/UHF band. Written by a team of experts for specialists and non-specialists alike, this book serves as a comprehensive guide to DTTB. It covers the fundamentals of channel coding and modulation technologies used in DTTB, as well as receiver technology for synchronization, channel estimation, and equalization. It also covers the recently introduced Chinese DTTB standard, using the SFN network in Hong Kong as an example.

  2. Digital processing optical transmission and coherent receiving techniques

    CERN Document Server

    Binh, Le Nguyen

    2013-01-01

    With coherent mixing in the optical domain and processing in the digital domain, advanced receiving techniques employing ultra-high speed sampling rates have progressed tremendously over the last few years. These advances have brought coherent reception systems for lightwave-carried information to the next stage, resulting in ultra-high capacity global internetworking. Digital Processing: Optical Transmission and Coherent Receiving Techniques describes modern coherent receiving techniques for optical transmission and aspects of modern digital optical communications in the most basic lines. The

  3. Digital Monopulse Receivers for Phase Modulated Signals

    Science.gov (United States)

    2005-04-14

    Mateo Burgos-García, Gema Ferreiro-Collar, Alberto Asensio Ló Grupo de Microondas y Dpto. Señales, Sistemas y Radio E.T.S.I. Telecomunic Universidad...Politécnica d Ciudad Universitaria 28040 Madrid, Spa Email: mateo@gmr.ssr. Digital Monopulse Rec Modulated Si T ∆ Σ Z1(t) Z2(t)log-amplifier of each...Microondas y Radar Dpto. Señales, Sistemas y Radiocomunicaciones E.T.S.I. Telecomunicación Universidad Politécnica de Madrid Ciudad Universitaria s/n

  4. A Digital-Receiver for the Murchison Widefield Array

    CERN Document Server

    Prabu, Thiagaraj; Roshi, D Anish; Kamini, P A; Madhavi, S; Emrich, David; Crosse, Brian; Williams, Andrew J; Waterson, Mark; Deshpande, Avinash A; Shankar, N Udaya; Subrahmanyan, Ravi; Briggs, Frank H; Goeke, Robert F; Tingay, Steven J; Johnston-Hollitt, Melanie; R, Gopalakrishna M; Morgan, Edward H; Pathikulangara, Joseph; Bunton, John D; Hampson, Grant; Williams, Christopher; Ord, Stephen M; Wayth, Randall B; Kumar, Deepak; Morales, Miguel F; deSouza, Ludi; Kratzenberg, Eric; Pallot, D; McWhirter, Russell; Hazelton, Bryna J; Arcus, Wayne; Barnes, David G; Bernardi, Gianni; Booler, T; Bowman, Judd D; Cappallo, Roger J; Corey, Brian E; Greenhill, Lincoln J; Herne, David; Hewitt, Jacqueline N; Kaplan, David L; Kasper, Justin C; Kincaid, Barton B; Koenig, Ronald; Lonsdale, Colin J; Lynch, Mervyn J; Mitchell, Daniel A; Oberoi, Divya; Remillard, Ronald A; Rogers, Alan E; Salah, Joseph E; Sault, Robert J; Stevens, Jamie B; Tremblay, S E; Webster, Rachel L; Whitney, Alan R; Wyithe, Stuart B

    2015-01-01

    An FPGA-based digital-receiver has been developed for a low-frequency imaging radio interferometer, the Murchison Widefield Array (MWA). The MWA, located at the Murchison Radio-astronomy Observatory (MRO) in Western Australia, consists of 128 dual-polarized aperture-array elements (tiles) operating between 80 and 300\\,MHz, with a total processed bandwidth of 30.72 MHz for each polarization. Radio-frequency signals from the tiles are amplified and band limited using analog signal conditioning units; sampled and channelized by digital-receivers. The signals from eight tiles are processed by a single digital-receiver, thus requiring 16 digital-receivers for the MWA. The main function of the digital-receivers is to digitize the broad-band signals from each tile, channelize them to form the sky-band, and transport it through optical fibers to a centrally located correlator for further processing. The digital-receiver firmware also implements functions to measure the signal power, perform power equalization across ...

  5. DIGITAL ERA: UTILIZE OF CLOUD COMPUTING TECHNOLOGY IN DIGITAL LIBRARY

    OpenAIRE

    T. RAGHUNADHA REDDY

    2012-01-01

    With the purpose of applying cloud computing to digital library, the paper initially describes cloud computing and analyzes current status of cloud computing in digital library. Then it proposes the architecture of cloud computing in digital library and summarises the application of cloud computing in digital library. Finally the author brings out the future improvement in digital library using cloud computing technology.

  6. Digital Downsides: Exploring University Students' Negative Engagements with Digital Technology

    Science.gov (United States)

    Selwyn, Neil

    2016-01-01

    Digital technologies are now an integral feature of university study. As such, academic research has tended to concentrate on the potential of digital technologies to support, extend and even "enhance" student learning. This paper, in contrast, explores the rather more messy realities of students' engagements with digital technology. In…

  7. SCORE DIGITAL TECHNOLOGY: THE CONVERGENCE

    Directory of Open Access Journals (Sweden)

    Chernyshov Alexander V.

    2013-12-01

    Full Text Available Explores the role of digital scorewriters in today's culture, education, and music industry and media environment. The main principle of the development of software is not only publishing innovation (relating to the sheet music, and integration into the area of composition, arrangement, education, creative process for works based on digital technology (films, television and radio broadcasting, Internet, audio and video art. Therefore the own convergence of musically-computer technology is a total phenomenon: notation program combined with means MIDI-sequencer, audio and video editor. The article contains the unique interview with the creator of music notation processors.

  8. CCTV networking and digital technology

    CERN Document Server

    Damjanovski, Vlado

    2005-01-01

    Closed circuit television (CCTV) is experiencing a leap in technology using digital techniques, networking and the Internet. The new edition of this high-level professional reference retains the particulars that made the first edition a success, including the details of CCD cameras, lenses, coaxial cables, fiber-optics, and system design, but it is expanded to cover all video compression techniques used in the ever increasing assortment of digital video recorders (DVRs) available on the market today. This new edition of the book CCTV demystifies DVR technology. It also serves to clarify the te

  9. Research on Digital Product Modeling Key Technologies of Digital Manufacturing

    Institute of Scientific and Technical Information of China (English)

    DING Guoping; ZHOU Zude; HU Yefa; ZHAO Liang

    2006-01-01

    With the globalization and diversification of the market and the rapid development of Information Technology (IT) and Artificial Intelligence (AI), the digital revolution of manufacturing is coming. One of the key technologies in digital manufacturing is product digital modeling. This paper firstly analyzes the information and features of the product digital model during each stage in the product whole lifecycle, then researches on the three critical technologies of digital modeling in digital manufacturing-product modeling, standard for the exchange of product model data and digital product data management. And the potential signification of the product digital model during the process of digital manufacturing is concluded-product digital model integrates primary features of each stage during the product whole lifecycle based on graphic features, applies STEP as data exchange mechanism, and establishes PDM system to manage the large amount, complicated and dynamic product data to implement the product digital model data exchange, sharing and integration.

  10. Digital signal processor and processing method for GPS receivers

    Science.gov (United States)

    Thomas, Jr., Jess B. (Inventor)

    1989-01-01

    A digital signal processor and processing method therefor for use in receivers of the NAVSTAR/GLOBAL POSITIONING SYSTEM (GPS) employs a digital carrier down-converter, digital code correlator and digital tracking processor. The digital carrier down-converter and code correlator consists of an all-digital, minimum bit implementation that utilizes digital chip and phase advancers, providing exceptional control and accuracy in feedback phase and in feedback delay. Roundoff and commensurability errors can be reduced to extremely small values (e.g., less than 100 nanochips and 100 nanocycles roundoff errors and 0.1 millichip and 1 millicycle commensurability errors). The digital tracking processor bases the fast feedback for phase and for group delay in the C/A, P.sub.1, and P.sub.2 channels on the L.sub.1 C/A carrier phase thereby maintaining lock at lower signal-to-noise ratios, reducing errors in feedback delays, reducing the frequency of cycle slips and in some cases obviating the need for quadrature processing in the P channels. Simple and reliable methods are employed for data bit synchronization, data bit removal and cycle counting. Improved precision in averaged output delay values is provided by carrier-aided data-compression techniques. The signal processor employs purely digital operations in the sense that exactly the same carrier phase and group delay measurements are obtained, to the last decimal place, every time the same sampled data (i.e., exactly the same bits) are processed.

  11. Digital-data receiver synchronization method and apparatus

    Science.gov (United States)

    Smith, Stephen F [Loudon, TN; Turner, Gary W [Clinton, TN

    2009-09-08

    Digital data receiver synchronization is provided with composite phase-frequency detectors, mutually cross-connected comparison feedback or both to provide robust reception of digital data signals. A single master clock can be used to provide frequency signals. Advantages can include fast lock-up time in moderately to severely noisy conditions, greater tolerance to noise and jitter when locked, and improved tolerance to clock asymmetries.

  12. Monobit Digital Receivers for QPSK: Design, Analysis and Performance

    CERN Document Server

    Wang, Zhiyong; Zhang, Wenyi; Wei, Guo

    2012-01-01

    Future communication system requires large bandwidth to achieve high data rate up to multigigabit/ sec, which makes analog-to-digital (ADC) become a key bottleneck for the implementation of digital receivers due to its high complexity and large power consumption. Therefore, monobit receivers for BPSK have been proposed to address this problem. In this work, QPSK modulation is considered for higher data rate. First, the optimal receiver based on monobit ADC with Nyquist sampling is derived, and its corresponding performance in the form of deflection ratio is calculated. Then a suboptimal but more practical monobit receiver is obtained, along with iterative demodulation and small sample removal. The effect of the imbalances between the In-phase (I) and Quadrature-phase (Q) branches, including the amplitude and phase imbalances, is carefully investigated too. To combat the performance loss caused by IQ imbalances, monobit receivers based on double training sequences are proposed. Numerical simulations show that ...

  13. Digital Front End for Wide-Band VLBI Science Receiver

    Science.gov (United States)

    Jongeling, Andre; Sigman, Elliott; Navarro, Robert; Goodhart, Charles; Rogstad, Steve; Chandra, Kumar; Finley, Sue; Trinh, Joseph; Soriano, Melissa; White, Les; hide

    2006-01-01

    An upgrade to the very-long-baseline-interferometry (VLBI) science receiver (VSR) a radio receiver used in NASA's Deep Space Network (DSN) is currently being implemented. The current VSR samples standard DSN intermediate- frequency (IF) signals at 256 MHz and after digital down-conversion records data from up to four 16-MHz baseband channels. Currently, IF signals are limited to the 265-to-375-MHz range, and recording rates are limited to less than 80 Mbps. The new digital front end, denoted the Wideband VSR, provides improvements to enable the receiver to process wider bandwidth signals and accommodate more data channels for recording. The Wideband VSR utilizes state-of-the-art commercial analog-to-digital converter and field-programmable gate array (FPGA) integrated circuits, and fiber-optic connections in a custom architecture. It accepts IF signals from 100 to 600 MHz, sampling the signal at 1.28 GHz. The sample data are sent to a digital processing module, using a fiber-optic link for isolation. The digital processing module includes boards designed around an Advanced Telecom Computing Architecture (ATCA) industry-standard backplane. Digital signal processing implemented in FPGAs down-convert the data signals in up to 16 baseband channels with programmable bandwidths from 1 kHz to 16 MHz. Baseband samples are transmitted to a computer via multiple Ethernet connections allowing recording to disk at rates of up to 1 Gbps.

  14. Digital preservation technology for cultural heritage

    CERN Document Server

    Zhou, Mingquan; Wu, Zhongke

    2012-01-01

    ""Digital Preservation Technology for Cultural Heritage"" discusses the technology and processes in digital preservation of cultural heritage. It covers topics in five major areas: Digitization of cultural heritage; Digital management in the cultural heritage preservation; Restoration techniques for rigid solid relics; Restoration techniques for paintings; Digital museum. It also includes application examples for digital preservation of cultural heritage. The book is intended for researchers, advanced undergraduate and graduate students in Computer Graphics and Image Processing as well as Cu

  15. Normalized Design of Multi-channel LIF Digital Receiver

    Institute of Scientific and Technical Information of China (English)

    方航锋; 郁发兴; 汪海航

    2004-01-01

    A design method for parallel processing application on multi-channel low-intermediate-frequency(LIF) digital receiver was presented. It is based on the DSP sub-array with a simple topology and operation timing to evaluate and determine the processing capability and then construct the parallel processing array for multi-channel signals according to the restriction of operation timing. Using this method, the design of multi-channel digital receiver may be simplified. Finally, a design example was used to show how to apply this method.

  16. Digital Natives and Digital Immigrants: Teaching with Technology

    Science.gov (United States)

    Martin, Ellen Marie Peterson

    2011-01-01

    Education is witnessing an increasing demand for technology use in the classroom. At the same time, new teachers are entering the profession in high numbers, some being labeled as "Digital Natives" while others are labeled "Digital Immigrants". This qualitative case study investigated the technology practices of Digital Native and Digital…

  17. DIGITAL ERA: UTILIZE OF CLOUD COMPUTING TECHNOLOGY IN DIGITAL LIBRARY

    Directory of Open Access Journals (Sweden)

    T. RAGHUNADHA REDDY

    2012-09-01

    Full Text Available With the purpose of applying cloud computing to digital library, the paper initially describes cloud computing and analyzes current status of cloud computing in digital library. Then it proposes the architecture of cloud computing in digital library and summarises the application of cloud computing in digital library. Finally the author brings out the future improvement in digital library using cloud computing technology.

  18. Design and Implementation of a Cueing Wideband Digital EW Receiver

    Institute of Scientific and Technical Information of China (English)

    ZHU Jun; TANG Bin; WU Wei; JIANG Zong-ming; ZHANG Chang-ju; YIN Mao-wei; DEN Ming-yi; DU Dong-ping

    2006-01-01

    A cueing wideband digital Electronic Warfare (EW) receiver is presented. The proposed receiver, which is to measure the instantaneous frequency and bandwidth of the intercept short-duration pulse radar signals that cue and match the corresponding ones, meets the requirements of good sensitivity and dynamic range for EW and can save hardware resources greatly as well. In addition, real-time signal processing, which is the main bottleneck for covering a wide instantaneous frequency band for EW receiver, is better solved in the proposed design structure. The highly efficient implementation and good parameter estimation algorithms are proposed as well. Theoretical analysis and experimental results show that this structure is feasible.

  19. Design of BPS digital frontend for software defined radio receiver

    Institute of Scientific and Technical Information of China (English)

    王洪梅; KIM Jae-hyung; 王法广; LEE Sang-hyuk; 王雪松

    2015-01-01

    In radio receivers, complete implementation of the software defined radio (SDR) concept is mainly limited by frontend. Based on bandpass sampling (BPS) theory, a flexible digital frontend (DFE) platform for SDR receiver is designed. In order to increase the processing speed, Gigabit Ethernet was applied in the platform at speed of 5×108 bit/s. By appropriate design of interpolant according to the position of input RF signals, multi-band receiving can be realized in the platform with suppression more than 35 dB without changing hardware.

  20. Digital Watermarking Technology with Practical Applications

    Directory of Open Access Journals (Sweden)

    Norishige Morimoto

    1999-01-01

    Full Text Available Digital watermarking technology has been actively studied and developed by a number of institutions and companies since mid ‘90s. This area draws more and more attention as one of the key technology elements for content management, copyright protection and copy control of digital contents. This article discusses several different types of digital watermark application, particularly the application of digital watermarks for DVD copy control. This would be the first digital watermark application requiring worldwide standardization.

  1. Digital terrestrial broadcasting receiver in the U.K; Eikoku chijoha digital hoso jushinki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Digital terrestrial broadcasting is broadcasted in parallel with existing UHF analog broadcasting, whereas each of allocated channel frequencies can transmit five to six programs simultaneously. Each home can receive a number of programs with the existing antenna without a need of installing a new satellite antenna or cable. Among the countries of the world running forward to digitization of broadcasting all at once, the U.K. develops advancing movements and leads the world by starting the digital terrestrial broadcasting. In addition to the digitized broadcasting of conventional analog broadcasting programs, the `Ondigitals` (broadcasting operators) have started newly the pay broadcasting. Toshiba has been selected as one of the six developers and manufacturers of digital terrestrial broadcasting receivers, and has developed the digital terrestrial broadcasting receiver DTB2000. For the modulation system, the orthogonal frequency division multiplex (OFDM) was chosen as a system being strong against ghost and most suitable for digital terrestrial broadcasting. In addition, the receiver is equipped with software download function by using the broadcasting waves, and the common interface being the communication specification specified in the DVB (digital video broadcasting) to provide future function expandability. (translated by NEDO)

  2. A floating-point digital receiver for MRI.

    Science.gov (United States)

    Hoenninger, John C; Crooks, Lawrence E; Arakawa, Mitsuaki

    2002-07-01

    A magnetic resonance imaging (MRI) system requires the highest possible signal fidelity and stability for clinical applications. Quadrature analog receivers have problems with channel matching, dc offset and analog-to-digital linearity. Fixed-point digital receivers (DRs) reduce all of these problems. We have demonstrated that a floating-point DR using large (order 124 to 512) FIR low-pass filters also overcomes these problems, automatically provides long word length and has low latency between signals. A preloaded table of finite impuls response (FIR) filter coefficients provides fast switching between one of 129 different one-stage and two-stage multrate FIR low-pass filters with bandwidths between 4 KHz and 125 KHz. This design has been implemented on a dual channel circuit board for a commercial MRI system.

  3. Weather satellite picture receiving stations, APT digital scan converter

    Science.gov (United States)

    Vermillion, C. H.; Kamowski, J. C.

    1975-01-01

    The automatic picture transmission digital scan converter is used at ground stations to convert signals received from scanning radiometers to data compatible with ground equipment designed to receive signals from vidicons aboard operational meteorological satellites. Information necessary to understand the circuit theory, functional operation, general construction and calibration of the converter is provided. Brief and detailed descriptions of each of the individual circuits are included, accompanied by a schematic diagram contained at the end of each circuit description. Listings of integral parts and testing equipment required as well as an overall wiring diagram are included. This unit will enable the user to readily accept and process weather photographs from the operational meteorological satellites.

  4. Digital video technology, today and tomorrow

    Science.gov (United States)

    Liberman, J.

    1994-10-01

    Digital video is probably computing's fastest moving technology today. Just three years ago, the zenith of digital video technology on the PC was the successful marriage of digital text and graphics with analog audio and video by means of expensive analog laser disc players and video overlay boards. The state of the art involves two different approaches to fully digital video on computers: hardware-assisted and software-only solutions.

  5. A novel digital receiver concept for ISRO's future remote sensing radars

    Science.gov (United States)

    Desai, Nilesh; Vachhani, J. G.; Soin, Sumit; Agrawal, Rinku; Rao, C. V. N.; Gujraty, Virendra; Rana, Surindersingh

    2006-12-01

    Technology development related to digital, antenna and RF subsystems for Microwave Radar Sensors like Synthetic Aperture Radar, Scatterometer, Altimeter and Radiometer is one of the major activities under ISRO's microwave remote sensing programme, since 1980s. These technologies are now being gainfully utilized for building ISRO's operational Earth Observation missions involving microwave sensors like Radar Imaging Satellite, RISAT SAR, Oceansat-2 Scatterometer, Megha-Tropiques, MADRAS and Airborne SAR for Disaster Management, DMSAR. Concurrently, advanced technology developments in these fields are underway to meet the major technological challenges of building ISRO's proposed advanced microwave missions like ultra-high resolution SAR's, Synthetic Aperture Radiometer (SARAD), Milli-meter and sub-millimeter wave sounders and SAR Constellations for Disaster management as well as Interferometric, Polarmetric and polarmetric interferometry applications. Also, these hardware are being designed with core radar electronics concept, in which the same RF and digital hardware sub-units / modules will be utilized to build different microwave radar sensors. One of the major and common requirements for all these active and passive microwave sensors is the moderate to highspeed data acquisition and signal processing system. Traditionally, the Data acquisition units for all these radar sensors are implemented as stand-alone units, following the radar receivers. For ISRO's C-band airborne SAR (ASAR) and RISAT high resolution SAR, we have designed and developed High Speed 8-bit ADC based I/Q Digitisers, operating at 30.814 MHz and 250 MHz sampling rates, respectively. With the increasing demand of wide bandwidth and ultra-high resolution in imaging and non-imaging radar systems, the technology trend worldwide is towards a digital receiver, involving bandpass or IF sampling, thus eliminating the need for RF down converters and analog IQ demodulators. In order to evolve a generic

  6. Digital Technology and Student Cognitive Development

    Science.gov (United States)

    Cavanaugh, J. Michael; Giapponi, Catherine C.; Golden, Timothy D.

    2016-01-01

    Digital technology has proven a beguiling, some even venture addictive, presence in the lives of our 21st century (millennial) students. And while screen technology may offer select cognitive benefits, there is mounting evidence in the cognitive neuroscience literature that digital technology is restructuring the way our students read and think,…

  7. Digital Technology and Student Cognitive Development

    Science.gov (United States)

    Cavanaugh, J. Michael; Giapponi, Catherine C.; Golden, Timothy D.

    2016-01-01

    Digital technology has proven a beguiling, some even venture addictive, presence in the lives of our 21st century (millennial) students. And while screen technology may offer select cognitive benefits, there is mounting evidence in the cognitive neuroscience literature that digital technology is restructuring the way our students read and think,…

  8. Digital Natives: Creating Emergent Exhibitions through Digital Technologies

    DEFF Research Database (Denmark)

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Dindler, Christian

    2011-01-01

    Digital Technology can support the creation of dialogical spaces in the museum, both playful and reflective, that allow audiences to engage in the ongoing construction and reproduction of cultural heritage creating novel connections between self and others and between past, present and future....... In this way, digital technology can contribute to the creation of emergent exhibitions in which the exhibition is created in dialogue between audiences and the museum. We present experiences from a current research project, the Digital Natives exhibition, in which digital technology was designed...... as an integral part of the exhibition to encourage dialogue between audiences and the exhibition materials and thereby investigate how the exhibition emerge as a result of this dialogic co-construction inside the exhibition space. In short, the opportunities offered by digital technologies prompts us to consider...

  9. Reanimating cultural heritage through digital technologies

    OpenAIRE

    Zhang, Wei

    2011-01-01

    Digital technologies are becoming extremely important for web-based cultural heritage applications. This thesis presents novel digital technology solutions to 'access and interact' with digital heritage objects and collections. These innovative solutions utilize service orientation (web services), workflows, and social networking and Web 2.0 mashup technologies to innovate the creation, interpretation and use of collections dispersed in a global museumscape, where community participation is a...

  10. Optical Network Technologies for Future Digital Cinema

    Directory of Open Access Journals (Sweden)

    Sajid Nazir

    2016-01-01

    Full Text Available Digital technology has transformed the information flow and support infrastructure for numerous application domains, such as cellular communications. Cinematography, traditionally, a film based medium, has embraced digital technology leading to innovative transformations in its work flow. Digital cinema supports transmission of high resolution content enabled by the latest advancements in optical communications and video compression. In this paper we provide a survey of the optical network technologies for supporting this bandwidth intensive traffic class. We also highlight the significance and benefits of the state of the art in optical technologies that support the digital cinema work flow.

  11. Simultaneous Transmit and Receive Performance of an 8-Channel Digital Phased Array

    Science.gov (United States)

    2017-01-16

    Receive (STAR) could provide significant benefits for many applications including communications, radar, spectral sens- ing, and multifunctional...shown in Fig . 1. Transmit digital beamforming is used to reduce the total coupled power at each receive element, allowing the receive array to maintain...Canceller Receive Digital Beamfomer Isolated Receive SignalTransmit Signal ALSTAR Transmit Elements ALSTAR Receive Elements ... ... Fig . 1

  12. Interference mitigation for simultaneous transmit and receive applications on digital phased array systems

    Science.gov (United States)

    Snow, Trevor M.

    As analog-to-digital (ADC) and digital-to-analog conversion (DAC) technologies become cheaper and digital processing capabilities improve, phased array systems with digital transceivers at every element will become more commonplace. These architectures offer greater capability over traditional analog systems and enable advanced applications such as multiple-input, multiple-output (MIMO) communications, adaptive beamforming, space-time adaptive processing (STAP), and MIMO for radar. Capabilities for such systems are still limited by the need for isolating self-interference from transmitters at co-located receivers. The typical approach of time-sharing the antenna aperture between transmitters and receivers works but leaves the receivers blind for a period of time. For full-duplex operation, some systems use separate frequency bands for transmission and reception, but these require fixed filtering which reduces the system's ability to adapt to its environment and is also an inefficient use of spectral resources. To that end, tunable, high quality-factor filters are used for sub-band isolation and protect receivers while allowing open reception at other frequencies. For more flexibility, another emergent area of related research has focused on co-located spatial isolation using multiple antennas and direct injection of interference cancellation signals into receivers, which enables same-frequency full-duplex operation. With all these methods, self-interference must be reduced by an amount that prevents saturation of the ADC. Intermodulation products generated in the receiver in this process can potentially be problematic, as certain intermodulation products may appear to come from a particular angle and cohere in the beamformer. This work explores various digital phased array architectures and the how the flexibility afforded by an all-digital beamforming architecture, layered with other methods of isolation, can be used to reduce self-interference within the system

  13. Digital technologies in Day-care institutions

    DEFF Research Database (Denmark)

    Schrøder, Vibeke; Søndergaard, Steen

    2016-01-01

    , in part by new technologies designed with an intuitive and inviting user interface. In a one-year research project ’Digital tools in day-care-institutions’ (2015) financed by The Danish Agency for Digitisation and The Ministry of Education we have investigated the role of digital technologies in relation......Digital technologies are gaining an ever increasing access into the activities in Danish and Nordic day-care institutions. The traditional critical viewpoint of technologies as being opposed to the well-being of children is challenged in part by substantial access to digital tools in infant life...... environments including digital technologies. From this follows a focus on the preferred activity of children: playing. In the paper we will elaborate on two – preliminary - interrelated - findings: 1) Children and adults are handling technologies in substantially different ways 2) The professionals...

  14. Digital Technologies and a Changing Profession

    DEFF Research Database (Denmark)

    Plesner, Ursula; Raviola, Elena

    Digital technologies are profoundly disturbing not only news delivery, but also the whole organization of news work. The relationship between digital technologies and news has been investigated especially in media and journalism studies. Scholars in these fields have followed the introduction...... of digital technologies into news work (Ursell, 2001; Pavlik, 2000, 2013; Saltzis and Dickinson, 2008; Meikle and Redden, 2011, Plesner 2010), and dealt with a range of organizational consequences of this development. In studies of news organizations, it has been pointed out that the question of digital...

  15. Digitalization and the global technology trends

    Science.gov (United States)

    Ignat, V.

    2017-08-01

    Digitalization, connected products and services, and shortening innovation cycles are widely discussed topics in management practice and theory and demand for new concepts. We analysed how companies innovated their business models and how are the new the technology trends. We found out, that have a positive approach to digitalization but the technology strategy still runs its original business model. Digitalization forces to new solution orientation. For companies it is necessary to master the digital transformation, new innovations have to be developed. Furthermore, digitalization / Industry 4.0 linking the real-life factory with virtual reality, will play an increasingly important role in global manufacturing. Companies have to obtain new digital capabilities, in order to make their company sustainable for the future. A long term growth and welfare in Europe could be guaranteed only by new technology innovation.

  16. Digital libraries: A testbed for multimedia technology

    Institute of Scientific and Technical Information of China (English)

    ZHUANG Yue-ting

    2005-01-01

    A distinguishing feature of a digital library is that it has Terabyte volumes of multimedia resources. One challenge for researchers in the field of multimedia is to find a testbed for showing the potentials of multimedia technologies such as video summarization, semantic annotation, multimedia cross indexing and retrieval, and etc. Deeper research and wider applications of digital libraries revealed their indispensable role as testbed for multimedia technologies. This paper presents challenging issues of some key techniques used in digital libraries and their specific needs for multimedia technologies.

  17. Authentication of digital medical images with digital signature technology.

    Science.gov (United States)

    Smith, J P

    1995-03-01

    To determine whether digital signature technology (DST) can authenticate digital medical images to the same level of authenticity required for interbank electronic transfer of funds. Message digests were computed for two magnetic resonance images that differed only by the value of a single bit. RSA (Rivest, Shamir, and Adleman) public key cryptography was used to encrypt each message digest to form a digital signature for each image, a process analogous to the established use of RSA DST for electronic funds transfer. The process was then reversed to authenticate the original image from its digital signature. Although the images differed by less than 0.000095%, their message digests differed at 94% of their characters. The digital signature of the original image proved that it was authentic and that the altered image was not authentic. RSA DST can establish the authenticity of images to at least the level of confidence required for interbank electronic transfer of funds.

  18. Digital technology and the conservation of nature

    NARCIS (Netherlands)

    Arts, K.A.J.; Wal, van der R.; Adams, W.M.

    2015-01-01

    Digital technology is changing nature conservation in increasingly profound ways. We describe this impact and its significance through the concept of ‘digital conservation’, which we found to comprise five pivotal dimensions: data on nature, data on people, data integration and analysis, communicati

  19. Digital Literacy and New Technological Perspectives

    Science.gov (United States)

    Feola, Elvia Ilaria

    2016-01-01

    This paper aims to reflect on the implications and challenges that experts in the field have to deal with when you want to evaluate the performance in the use of digital technologies in teaching. The argument stems from a contextual and social assessment, and then proceeds to an application and methodological connotation of digital literacy…

  20. Digital Technologies and a Changing Profession

    DEFF Research Database (Denmark)

    Plesner, Ursula; Raviola, Elena

    Digital technologies are profoundly disturbing not only news delivery, but also the whole organization of news work. The relationship between digital technologies and news has been investigated especially in media and journalism studies. Scholars in these fields have followed the introduction...... of digital technologies into news work (Ursell, 2001; Pavlik, 2000, 2013; Saltzis and Dickinson, 2008; Meikle and Redden, 2011, Plesner 2010), and dealt with a range of organizational consequences of this development. In studies of news organizations, it has been pointed out that the question of digital...... technology appropriation is not just important for technical or economic reasons, but because it affects organizational structures, work practices and representations (Boczkowski, 2004). For instance, reporters and editors must manage market pressures and time pressures in new ways (Klinenberg, 2005) due...

  1. Design guidelines for SAR digital receiver/exciter boards.

    Energy Technology Data Exchange (ETDEWEB)

    Dudley, Peter A.

    2009-08-01

    High resolution radar systems generally require combining fast analog to digital converters and digital to analog converters with very high performance digital signal processing logic. These mixed analog and digital printed circuit boards present special challenges with respect to electromagnetic interference. This document first describes the mechanisms of interference on such boards then follows up with a discussion of prevention techniques and finally provides a checklist for designers to help avoid common mistakes.

  2. Update on new technologies in digital mammography

    Directory of Open Access Journals (Sweden)

    Patterson SK

    2014-08-01

    Full Text Available Stephanie K Patterson, Marilyn A Roubidoux Division of Breast Imaging, Department of Radiology, University of Michigan Health System, Ann Arbor, MI, USA Abstract: Despite controversy regarding mammography's efficacy, it continues to be the most commonly used breast cancer-screening modality. With the development of digital mammography, some improved benefit has been shown in women with dense breast tissue. However, the density of breast tissue continues to limit the sensitivity of conventional mammography. We discuss the development of some derivative digital technologies, primarily digital breast tomosynthesis, and their strengths, weaknesses, and potential patient impact. Keywords: screening mammography, breast cancer, contrast media, digital breast tomosynthesis

  3. Incorporating digital technologies into science classes

    DEFF Research Database (Denmark)

    Hilton, Annette; Hilton, Geoff

    2013-01-01

    learning. There is a need for research that examines the ways in which digital technologies impact on teaching practices and learning outcomes. This paper describes case studies from two larger studies that examined ways in which digital technologies could be used to promote students’ understanding...... in science. The first case study involved primary school students (12 years old) using digital video production to record and represent their learning in science. This study extended writing-to-learn approaches to include video production to learn. The second case study involved Year 11 chemistry students...

  4. Analysis of parallel optical sampling rate and ADC requirements in digital coherent receivers

    DEFF Research Database (Denmark)

    Lorences Riesgo, Abel; Galili, Michael; Peucheret, Christophe

    2012-01-01

    We comprehensively assess analog-to-digital converter requirements in coherent digital receiver schemes with parallel optical sampling. We determine the electronic requirements in accordance with the properties of the free running local oscillator....

  5. Digital filter technology and its application to geomagnetic pulsations in Antarctica

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Digital filter technology is an important method in study of geomagnetic pulsations in Antarctica. The signals received by pulsation magnetometer on the ground include various types of magnetic pulsations. Some types of pulsations or some frequency hands of pulsations can be extracted from the signals by means of digital filter technology because types of pulsations are defined according to their frequency range. In this paper usual digital filter technology is provided for study of magnetic pulsations in Antarctica and some examples are introduced.

  6. Simultaneous Transmit and Receive Performance of an 8-channel Digital Phased Array

    Science.gov (United States)

    2017-01-16

    Simultaneous Transmit and Receive Performance of an 8- channel Digital Phased Array Jonathan P. Doane, Kenneth E. Kolodziej, Bradley T. Perry MIT...traditional digital cancellation is typically limited by channel noise and distortion. A unique aspect of the ALSTAR digital canceller is the use of...elements, and an 8- channel digital transceiver chassis. width which is mixed to an IF center frequency of 187.5 MHz, supporting digital sampling in the

  7. Tweens' Characterization of Digital Technologies

    Science.gov (United States)

    Brito, Pedro Quelhas

    2012-01-01

    The tweens are a transitional age group undergoing deep physical and psychological transformations. Based on a thirteen-focus group research design involving 103 students, and applying a tweens-centered approach, the characteristics of SMS, IM, Internet, digital photos, electronic games, and email were analyzed. Categories such as moral issues,…

  8. How we cope with digital technology

    CERN Document Server

    Turner, Phil

    2013-01-01

    Digital technology has become a defining characteristic of modern life. Almost everyone uses it, we all rely on it, and many of us own a multitude of devices. What is more, we all expect to be able to use these technologies ""straight out the box."" This lecture discusses how we are able to do this without apparent problems. We are able to use digital technology because we have learned to cope with it. ""To cope"" is used in philosophy to mean ""absorbed engagement,"" that is, we use our smart phones and tablet computers with little or no conscious effort. In human-computer interaction this ki

  9. Algorithms for Digital Micro-Wave Receivers and Optimal System Identification.

    Science.gov (United States)

    1994-02-28

    estimation, Frequency estimation, Digital receiver design, Improved AR and ARMA modeling, Electronic Warfare (EW) signal detection, Optimal system identification from input/output and frequency domain data.

  10. CMOS digital pixel sensors: technology and applications

    Science.gov (United States)

    Skorka, Orit; Joseph, Dileepan

    2014-04-01

    CMOS active pixel sensor technology, which is widely used these days for digital imaging, is based on analog pixels. Transition to digital pixel sensors can boost signal-to-noise ratios and enhance image quality, but can increase pixel area to dimensions that are impractical for the high-volume market of consumer electronic devices. There are two main approaches to digital pixel design. The first uses digitization methods that largely rely on photodetector properties and so are unique to imaging. The second is based on adaptation of a classical analog-to-digital converter (ADC) for in-pixel data conversion. Imaging systems for medical, industrial, and security applications are emerging lower-volume markets that can benefit from these in-pixel ADCs. With these applications, larger pixels are typically acceptable, and imaging may be done in invisible spectral bands.

  11. Digital technology and the conservation of nature.

    Science.gov (United States)

    Arts, Koen; van der Wal, René; Adams, William M

    2015-11-01

    Digital technology is changing nature conservation in increasingly profound ways. We describe this impact and its significance through the concept of 'digital conservation', which we found to comprise five pivotal dimensions: data on nature, data on people, data integration and analysis, communication and experience, and participatory governance. Examining digital innovation in nature conservation and addressing how its development, implementation and diffusion may be steered, we warn against hypes, techno-fix thinking, good news narratives and unverified assumptions. We identify a need for rigorous evaluation, more comprehensive consideration of social exclusion, frameworks for regulation and increased multi-sector as well as multi-discipline awareness and cooperation. Along the way, digital technology may best be reconceptualised by conservationists from something that is either good or bad, to a dual-faced force in need of guidance.

  12. Incorporating digital technologies into science classes

    DEFF Research Database (Denmark)

    Hilton, Annette; Hilton, Geoff

    2013-01-01

    in science. The first case study involved primary school students (12 years old) using digital video production to record and represent their learning in science. This study extended writing-to-learn approaches to include video production to learn. The second case study involved Year 11 chemistry students...... (16 years old) learning about and with multiple digital representations in a unit on chemical bonding. Both qualitative and quantitative data were collected in the studies. The findings revealed that using digital technologies in student-centred activities can promote a range of positive outcomes...

  13. Building the digital enterprise a guide to constructing monetization models using digital technologies

    CERN Document Server

    Skilton, Mark

    2015-01-01

    The digital economy is at a tipping point. This practical book defines digital ecosystems, discusses digital design using converging technologies of social networking, mobility, big data and cloud computing, and provides a methods for linking digital technologies together to meet the challenges of building a digital enterprise in the new economy.

  14. Sustainability, cognitive technologies and the digital semiosphere

    DEFF Research Database (Denmark)

    Bruni, Luis Emilio

    2015-01-01

    The convergence of digital and multimodal cognitive technologies offers the possibility to interact in an ‘on-line’ cultural process mediated by new ways of representing our thoughts, emotions, ideas, beliefs, opinions and behaviours. Such technological integration not only alters and introduces...... innovations in the interactive and representational modes of networked media, perhaps inducing changes in our cognitive functions, but also conditions the global cultural dynamics by potentially organizing, funnelling, tagging and ‘semantically’ predigesting knowledge through the ‘intelligent’ digital...

  15. The Effects of Narrowband Interference on Finite-Resolution IR-UWB Digital Receiver

    CERN Document Server

    zhang, chao; Ren, Pinyi

    2010-01-01

    Finite-resolution digital receiver is recently considered as a potential way to Ultra Wide Band (UWB) communication systems due to its ability of mitigating the challenge of Analog-Digital Converter (ADC). In this paper, the effects of narrowband interference (NBI) are investigated when finite-resolution digital receiver is used for Impulse Radio-UWB (IR-UWB) system. It is shown that finite-resolution receiver enlarges the impact of NBI. The lower resolution of the UWB receiver is, the more degradations NBI causes.

  16. Utilising digital technology for dialogue and evaluation

    DEFF Research Database (Denmark)

    Kjærgaard, Thomas

    2016-01-01

    This article investigates how digital technology can enhance evaluation and eflection through dialogue in a theory lesson in the context of university college teaching. The pedagogical designs in the article vary from synchronous classroom evaluation on smartphones, to online discussion fora...

  17. Utilising digital technology for dialogue and evaluation

    DEFF Research Database (Denmark)

    Kjærgaard, Thomas

    2016-01-01

    This article investigates how digital technology can enhance evaluation and reflection through dialogue in a theory lesson in the context of university college teaching. The pedagogical designs in the article vary from synchronous classroom evaluation on smartphones, to online discussion fora...

  18. Mobile technology and the digitization of healthcare.

    Science.gov (United States)

    Bhavnani, Sanjeev P; Narula, Jagat; Sengupta, Partho P

    2016-05-07

    The convergence of science and technology in our dynamic digital era has resulted in the development of innovative digital health devices that allow easy and accurate characterization in health and disease. Technological advancements and the miniaturization of diagnostic instruments to modern smartphone-connected and mobile health (mHealth) devices such as the iECG, handheld ultrasound, and lab-on-a-chip technologies have led to increasing enthusiasm for patient care with promises to decrease healthcare costs and to improve outcomes. This 'hype' for mHealth has recently intersected with the 'real world' and is providing important insights into how patients and practitioners are utilizing digital health technologies. It is also raising important questions regarding the evidence supporting widespread device use. In this state-of-the-art review, we assess the current literature of mHealth and aim to provide a framework for the advances in mHealth by understanding the various device, patient, and clinical factors as they relate to digital health from device designs and patient engagement, to clinical workflow and device regulation. We also outline new strategies for generation and analysis of mHealth data at the individual and population-based levels.

  19. Utilising digital technology for dialogue and evaluation

    DEFF Research Database (Denmark)

    Kjærgaard, Thomas

    2016-01-01

    This article investigates how digital technology can enhance evaluation and reflection through dialogue in a theory lesson in the context of university college teaching. The pedagogical designs in the article vary from synchronous classroom evaluation on smartphones, to online discussion fora as ...

  20. DIGITAL TECHNOLOGY BUSINESS CASE METHODOLOGY GUIDE & WORKBOOK

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Ken; Lawrie, Sean; Hart, Adam; Vlahoplus, Chris

    2014-09-01

    Performance advantages of the new digital technologies are widely acknowledged, but it has proven difficult for utilities to derive business cases for justifying investment in these new capabilities. Lack of a business case is often cited by utilities as a barrier to pursuing wide-scale application of digital technologies to nuclear plant work activities. The decision to move forward with funding usually hinges on demonstrating actual cost reductions that can be credited to budgets and thereby truly reduce O&M or capital costs. Technology enhancements, while enhancing work methods and making work more efficient, often fail to eliminate workload such that it changes overall staffing and material cost requirements. It is critical to demonstrate cost reductions or impacts on non-cost performance objectives in order for the business case to justify investment by nuclear operators. This Business Case Methodology approaches building a business case for a particular technology or suite of technologies by detailing how they impact an operator in one or more of the three following areas: Labor Costs, Non-Labor Costs, and Key Performance Indicators (KPIs). Key to those impacts will be identifying where the savings are “harvestable,” meaning they result in an actual reduction in headcount and/or cost. The report consists of a Digital Technology Business Case Methodology Guide and an accompanying spreadsheet workbook that will enable the user to develop a business case.

  1. Digital coherent receiver employing photonic downconversion for phase modulated radio-over-fibre links

    DEFF Research Database (Denmark)

    Zibar, Darko; Caballero Jambrina, Antonio; Guerrero Gonzalez, Neil

    2009-01-01

    A digital coherent receiver employing photonic downconversion is presented and experimentally demonstrated for phase-modulated radio-over-fibre optical links. The receiver is capable of operating at frequencies exceeding the bandwidth of electrical analog-to-digital converter by using photonic...... downconversion to translate the high-frequency input RF signal to the operating frequency range of the analog-to-digital converter. First, using linear digital demodulation scheme we measure SFDR of the link at microwave frequency of 5 GHz. Thereafter, successful signal demodulation of 50 Mbit/s binary phase...... shift keying (BPSK) modulated data signal at 5 GHz RF carrier frequency is experimentally demonstrated by using an analog-to-digital converter with only 1 GHz bandwidth. We successfully demonstrate signal demodulation, using the proposed digital coherent receiver with photonic downconversion, after 40...

  2. College of Engineering receives $1 million computing technology grant

    OpenAIRE

    Nystrom, Lynn A.

    2007-01-01

    A $1 million grant of Fujitsu technology and services to Virginia Tech's College of Engineering will assist in the college's creation of "digital opportunities" for underserved students, as well as pre-college students interested in studying math, science or engineering at Virginia Tech.

  3. Advanced Equalization Techniques for Digital Coherent Optical Receivers

    DEFF Research Database (Denmark)

    Arlunno, Valeria

    This PhD thesis addresses the design and performance evaluation of advanced Digital Signal Processing (DSP) algorithms for coherent optical fiber transmission systems. The research results presented in this thesis report on transmission of highly spectrally efficient optical communication systems...... employing multiplexing techniques with polarization multiplexing and multi-level modulations format. Advanced digital signal processing techniques offer robustness and flexibility for next generation high capacity optical fibre networks and are therefore considered as key building blocks in next generation...... format detection. Feedback equalization structure have been investigated in high order modulation formats transmission, when combined with coding techniques, and for closed spaced multiplexing scenario. Highlight results presented in this PhD thesis include evaluation and implementation of a novel...

  4. Handbook of digital games and entertainment technologies

    CERN Document Server

    Rauterberg, Matthias; Ciancarini, Paolo

    2017-01-01

    The topics treated in this handbook cover all areas of games and entertainment technologies, such as digital entertainment; technology, design/art, and sociology. The handbook consists of contributions from top class scholars and researchers from the interdisciplinary topic areas.  The aim of this handbook is to serving as a key reference work in the field and provides readers with a holistic picture of this interdisciplinary field covering technical issues, aesthetic/design issues, and sociological issues. At present, there is no reference work in the field that provides such a broad and complete picture of the field. Engineers and researchers who want to learn about this emerging area will be able to find adequate answers regarding technology issues on digital entertainment. Designers and artists can learn how their skills and expertise can contribute to this emerging area. Also researchers working in the field of sociology and psychology will find how their experience and knowledge are connected to other ...

  5. Technological Integration of Acquisitions in Digital Industries

    DEFF Research Database (Denmark)

    Henningsson, Stefan; Toppenberg, Gustav

    2015-01-01

    challenges in process and product integration. Through a case study of Network Solutions Corp. (NSC), a Fortune 500 company that has acquired more than 175 business units, we develop four propositions explaining how the benefits of platform core and complement acquisitions are differently contingent......Acquisitions have become essential tools to retain the technological edge in digital industries. This paper analyses the technological integration challenges in such acquisitions. Acquirers in digital industries are typically platform leaders in platform markets. They acquire (a) other platform...... providers to extend the platform core and to derive network effects by consolidating platform user groups, and (b) complement providers to create monopoly positions for the complements and for innovation complementarity. To enable these acquisition benefits, acquirers face technological integration...

  6. Design Architecture and Initial Results from an FPGA Based Digital Receiver for Multistatic Meteor Measurements

    Science.gov (United States)

    Palo, Scott; Vaudrin, Cody

    Defined by a minimal RF front-end followed by an analog-to-digital converter (ADC) and con-trolled by a reconfigurable logic device (FPGA), the digital receiver will replace conventional heterodyning analog receivers currently in use by the COBRA meteor radar. A basic hardware overview touches on the major digital receiver components, theory of operation and data han-dling strategies. We address concerns within the community regarding the implementation of digital receivers in small-scale scientific radars, and outline the numerous benefits with a focus on reconfigurability. From a remote sensing viewpoint, having complete visibility into a band of the EM spectrum allows an experiment designer to focus on parameter estimation rather than hardware limitations. Finally, we show some basic multistatic receiver configurations enabled through GPS time synchronization. Currently, the digital receiver is configured to facilitate range and radial velocity determination of meteors in the MLT region for use with the COBRA meteor radar. Initial measurements from data acquired at Platteville, Colorado and Tierra Del Fuego in Argentina will be presented. We show an improvement in detection rates compared to conventional analog systems. Scientific justification for a digital receiver is clearly made by the presentation of RTI plots created using data acquired from the receiver. These plots reveal an interesting phenomenon concerning vacillating power structures in a select number of meteor trails.

  7. How Digital Health Technology Aids Physicians

    Directory of Open Access Journals (Sweden)

    Nik Tehrani

    2015-06-01

    Full Text Available There is so much health and medical information available today that physicians cannot be expected to know it all. Thus, advances in technology have become a necessity for doctors to track patient information and care, and add to patient databases for reference and to conduct research. It is important to understand the new language of digital health, such as Personal Health Record (PHR, Electronic Medical Record (EMR and Electronic Health Record (EHR, all of which sound similar, but are not interchangeable. The ideal comprehensive IT system would empower patients, advance healthcare delivery and transform patient data into life-saving research (Kaiser, 2015. OmniFluent Health is language translation software that will allow for better patient/practitioner communication and avoid errors. Digital technology employs the use of big data that is shared, accessed, compiled and applied using analytics. However, information transfer, especially as mandated by current ethics of use of technology, has resulted into breach of patient privacy. Improved digital technology is providing the health care field with upgrades that are necessary, electronic files and health records, from mobile apps, and remote monitoring devices.

  8. Wireless receiver architectures and design antennas, RF, synthesizers, mixed signal, and digital signal processing

    CERN Document Server

    Rouphael, Tony J

    2014-01-01

    Wireless Receiver Architectures and Design presents the various designs and architectures of wireless receivers in the context of modern multi-mode and multi-standard devices. This one-stop reference and guide to designing low-cost low-power multi-mode, multi-standard receivers treats analog and digital signal processing simultaneously, with equal detail given to the chosen architecture and modulating waveform. It provides a complete understanding of the receiver's analog front end and the digital backend, and how each affects the other. The book explains the design process in great detail, s

  9. Digital Receivers for Low-Frequency Radio Telescopes UTR-2, URAN, GURT

    Science.gov (United States)

    Zakharenko, V.; Konovalenko, A.; Zarka, P.; Ulyanov, O.; Sidorchuk, M.; Stepkin, S.; Koliadin, V.; Kalinichenko, N.; Stanislavsky, A.; Dorovskyy, V.; Shepelev, V.; Bubnov, I.; Yerin, S.; Melnik, V.; Koval, A.; Shevchuk, N.; Vasylieva, I.; Mylostna, K.; Shevtsova, A.; Skoryk, A.; Kravtsov, I.; Volvach, Y.; Plakhov, M.; Vasilenko, N.; Vasylkivskyi, Y.; Vavriv, D.; Vinogradov, V.; Kozhin, R.; Kravtsov, A.; Bulakh, E.; Kuzin, A.; Vasilyev, A.; Ryabov, V.; Reznichenko, A.; Bortsov, V.; Lisachenko, V.; Kvasov, G.; Mukha, D.; Litvinenko, G.; Brazhenko, A.; Vashchishin, R.; Pylaev, O.; Koshovyy, V.; Lozinsky, A.; Ivantyshyn, O.; Rucker, H. O.; Panchenko, M.; Fischer, G.; Lecacheux, A.; Denis, L.; Coffre, A.; Grießmeier, J.-M.

    This paper describes digital radio astronomical receivers used for decameter and meter wavelength observations. Since 1998, digital receivers performing on-the-fly dynamic spectrum calculations or waveform data recording without data loss have been used at the UTR-2 radio telescope, the URAN VLBI system, and the GURT new generation radio telescope. Here, we detail these receivers developed for operation in the strong interference environment that prevails in the decameter wavelength range. Data collected with these receivers allowed us to discover numerous radio astronomical objects and phenomena at low frequencies, a summary of which is also presented.

  10. Access to digital technology among families coming to urban pediatric primary care clinics.

    Science.gov (United States)

    Demartini, Tori L; Beck, Andrew F; Klein, Melissa D; Kahn, Robert S

    2013-07-01

    Digital technologies offer new platforms for health promotion and disease management. Few studies have evaluated the use of digital technology among families receiving care in an urban pediatric primary care setting. A self-administered survey was given to a convenience sample of caregivers bringing their children to 2 urban pediatric primary care centers in spring 2012. The survey assessed access to home Internet, e-mail, smartphone, and social media (Facebook and Twitter). A "digital technology" scale (0-4) quantified the number of available digital technologies and connections. Frequency of daily use and interest in receiving medical information digitally were also assessed. The survey was completed by 257 caregivers. The sample was drawn from a clinical population that was 73% African American and 92% Medicaid insured with a median patient age of 2.9 years (interquartile range 0.8-7.4). Eighty percent of respondents reported having Internet at home, and 71% had a smartphone. Ninety-one percent reported using e-mail, 78% Facebook, and 27% Twitter. Ninety-seven percent scored ≥1 on the digital technology scale; 49% had a digital technology score of 4. The digital technology score was associated with daily use of digital media in a graded fashion (P < .0001). More than 70% of respondents reported that they would use health care information supplied digitally if approved by their child's medical provider. Caregivers in an urban pediatric primary care setting have access to and frequently use digital technologies. Digital connections may help reach a traditionally hard-to-reach population.

  11. Development of a digital TV receivers test suite

    Directory of Open Access Journals (Sweden)

    Pablo Flores-Guridi

    2015-01-01

    Full Text Available El despliegue de la televisión digital en Uruguay está en curso , siguiendo el estándar ISDB-Tb. Ya se completó el proceso de a signación de canales y, después de aprobado un protocolo de homologación, se ha comenzado a importar receptores o decodificadores desde principios de 2014. La certific ación es de capital importancia para acelerar la migra ción y para brindar una plataforma a los desarrolladores locales. El presente artículo resume los aspectos clave de este trabajo: el análisis de las norm as, la elaboración del Protoco lo de Homologación y la experiencia obtenida en la aplicación de las pruebas. Su objetivo es compartir estas experienc ias para contr ibuir en los procesos de adopción de la TV di gital, con lo que se espera ayu dar a que otros países o actore s puedan evitar problemas de com patibilidad o cumplimiento de las normas que aparecieron durante este traba jo, tanto en la regulación como e n los dispositivos ensayados.

  12. System design for a million channel digital spectrum analyzer /MCSA/. [of bandpass filtering in SETI receivers

    Science.gov (United States)

    Peterson, A.; Narasimha, M.; Narayan, S.

    1980-01-01

    The system design of a wideband (8 MHz) million-channel digital spectrum analyzer for use with a SETI receiver is presented. The analyzer makes use of a digital bandpass filter bank for transforming the wideband input signal into a specified number (120) of uniform narrowband output channels by the use of a Fourier transform digital processor combined with a prototype digital weighting network (finite impulse response filter). The output is then processed separately by 120 microprocessor-based discrete Fourier transform computers, each producing 8190 output channels of approximately 8 Hz bandwidth by the use of an 8190-point prime factor algorithm.

  13. Deconstructing Digital Natives: Young People, Technology, and the New Literacies

    Science.gov (United States)

    Thomas, Michael, Ed.

    2011-01-01

    There have been many attempts to define the generation of students who emerged with the Web and new digital technologies in the early 1990s. The term "digital native" refers to the generation born after 1980, which has grown up in a world where digital technologies and the internet are a normal part of everyday life. Young people belonging to this…

  14. Digital Mock-up Technology in Product Development and Research

    Institute of Scientific and Technical Information of China (English)

    CHEN Xu; ZHANG Pandeng; YANG Cheng; XU Zhongming

    2006-01-01

    After introducing the present status of digital mock-up (DMU) technology in product development and research, the modeling and its key technologies in product design are described. The architecture of digital design platform system for main DMU model is developed. Based on the architecture, a method of skeleton design has been applied to the development of digital design system.

  15. Differentiating Digital Writing Instruction: The Intersection of Technology, Writing Instruction, and Digital Genre Knowledge

    Science.gov (United States)

    Martin, Nicole M.; Lambert, Claire

    2015-01-01

    U.S. adolescents' prior technology experiences and exposure to digital genres vary, but they will often write digital texts as they enter college and adulthood. We explored middle school students' digital writing instructional experience in the context of a university-based summer digital writing camp. The sixth- through eighth-grade adolescents…

  16. The impact of digital technologies on teaching and learning

    OpenAIRE

    Banyard, P

    2015-01-01

    This thesis explores the impact of new technologies on learning and teaching and draws on research work carried out over a ten-year period. The thesis looks at the facilitators and barriers to using digital technologies effectively and explores the challenges for educators as they respond to the changes brought about by these digital technologies. It presents eight published works that have investigated the impact of digital technologies and collected data using a range of qualitative and qua...

  17. Digital Technology and Mental Health Interventions: Opportunities and Challenges

    Directory of Open Access Journals (Sweden)

    Aguilera, Adrian

    2015-02-01

    Full Text Available The growth of the Internet, mobile phones, social media and other digital technologies has changed our world in many ways. It has provided individuals with information that was previously only available to a select few. An example of the reach of technology is data that as of October 2012, there are over 6 billion phones worldwide (BBC, 2012. The availability of data in real time has presented hopes of intervening more efficiently and managing health problems by leveraging limited human resources. It also has an impact in changing the roles of providers and patients and in legal and ethical issues including privacy in digital health interactions. This paper will discuss why digital technology has received recent attention in the area of mental health, present some applications of technology for mental health to date, explore the challenges to full implementation in clinical settings, and present future opportunities for digital technologies.El crecimiento del Internet, los teléfonos móviles, las redes sociales y otras tecnologías digitales ha cambiado nuestro mundo de muchas maneras. Ha proporcionado a las personas con la información que antes sólo estaba disponible para un grupo selecto, por ejemplo a partir de octubre de 2012. Un ejemplo del alcance de la tecnología son los datos que dicen que hay más de 6 millones de teléfonos en todo el mundo (BBC, 2012. La disponibilidad de los datos en tiempo real a presentado la esperanza de intervenir de manera más eficiente y manejar los problemas de salud los recursos humanos limitados. También tiene un impacto en el cambio de los roles de los proveedores y los pacientes y en aspectos legales y éticos, incluyendo la privacidad en las interacciones de salud digital. Este artículo discutirá unas razones por cual la tecnología digital ha recibido atención recientemente en el área de salud mental, presentará algunas aplicaciones de la tecnología para mejorar la salud mental hasta la fecha

  18. Approaches towards Implementation of Multi-bit Digital Receiver using Fast Fourier Transform

    Directory of Open Access Journals (Sweden)

    Abhijit S. Kulkarni

    2013-03-01

    Full Text Available This paper compares different digital receiver signal processing schemes as applied to current ESM/RWR systems. The schemes include fast fourier transform (FFT-based, FIR filter-based and mixed architectures. Use of polyphase FFT and IIR filters is also discussed. The specifications and signal processing requirements of a modern digital electronic warfare (EW receiver are discussed. The design procedures and architectures for all the schemes are brought out. The tradeoffs involved in selection of different parameters for these schemes are also discussed. The digital receiver schemes are modeled and analyzed for different metrics such as, Parameter measurement accuracies, Pulse handling capability, Frequency separation capability, Number of multipliers required for implementation etc. The analysis is done for a 500 MHz BW digital receiver and assumes 8 bit ADC in the front end. The results obtained for the comparison are discussed in the paper. Limited simulations show that overlapped FFT scheme is a better approach for digital receiver processing.Defence Science Journal, 2013, 63(2, pp.198-203, DOI:http://dx.doi.org/10.14429/dsj.63.4264

  19. Learning by Playing with Digital Technology

    DEFF Research Database (Denmark)

    Benjaminsen, Nana

    2006-01-01

    This paper presupposes the notion that there is potential for the integration of play into primary and secondary school activities, because it can stimulate and support the formal as well as informal learning that takes place in school. Digital technology could be a driver for this integration...... Construction Games in Schools. The project is an exploration of how elements of play can be integrated in a technology-based learning environment. I will use examples of empirical data gathered during spring 2006 to demonstrate that play can function as a useful learning strategy, and also point out barriers...... for the integration of play in schools, because play activities conflict with the existing school structure on a fundamental level. The paper will end with a discussion where I question what type of learning environment the play oriented product Lego Robolab generates, and explore how play as a part of a learning...

  20. Learning by Playing with Digital Technology

    DEFF Research Database (Denmark)

    Benjaminsen, Nana

    2006-01-01

    Construction Games in Schools. The project is an exploration of how elements of play can be integrated in a technology-based learning environment. I will use examples of empirical data gathered during spring 2006 to demonstrate that play can function as a useful learning strategy, and also point out barriers...... strategy might lead to changes on three interrelated levels: the teaching material, the educational context (i.e. teaching style, use of the physical facilities and schools organisational structure) and the cultural-historical way schools function within Danish in society.......This paper presupposes the notion that there is potential for the integration of play into primary and secondary school activities, because it can stimulate and support the formal as well as informal learning that takes place in school. Digital technology could be a driver for this integration...

  1. Digital Technology for Geological Field Mapping

    Science.gov (United States)

    Rourke, Peter; Smith, Stuart; Vaughan, Alan; Ellis, Jenny

    2014-05-01

    The amount of time that students and professionals spend in the field has reduced over the past 25 years (Gibbs, 2012). Recent advances in technology are changing the way students and professionals are able to conduct geological field study. Applications such as Midland Valley Exploration's FieldMove Clino now allow the geologist to use their smartphone as a fast, georeferenced measuring device compared with a traditional compass-clinometer. Although we support the view that an understanding of field mapping and model building, taught at university level, is essential to give the geologist the ability to think in three and four dimensions, new technologies that automate the ability to digitise and visualise data in the field lead to a better appreciation of the geometry, scale, and evolution of geological structures and trapping mechanisms that will be encountered during a career in industry. The majority of future industry professionals own a smartphone or tablet device: A recent study found that four-fifths of new students own a smartphone and one-fifth own a tablet device (UCAS Media, 2013). This figure is increasing with each new intake of geoscience students. With the increased availability and affordability of smartphone and tablet devices, new techniques are being examined for digital data collection in the field. If the trend continues that geoscience students are likely to spend less time in the field than their predecessors, then the time available must be spent as effectively as possible. Digital devices allow students and professionals alike to optimise the time spent in the field, allowing more time to think about geological relationships, and highlighting areas of uncertainty that can be studied further. This poster will examine the use of new digital smartphone and tablet devices for the collection of geological field data.

  2. A digital receiver module with direct data acquisition for magnetic resonance imaging systems.

    Science.gov (United States)

    Tang, Weinan; Sun, Hongyu; Wang, Weimin

    2012-10-01

    A digital receiver module for magnetic resonance imaging (MRI) with detailed hardware implementations is presented. The module is based on a direct sampling scheme using the latest mixed-signal circuit design techniques. A single field-programmable gate array chip is employed to perform software-based digital down conversion for radio frequency signals. The modular architecture of the receiver allows multiple acquisition channels to be implemented on a highly integrated printed circuit board. To maintain the phase coherence of the receiver and the exciter in the context of direct sampling, an effective phase synchronization method was proposed to achieve a phase deviation as small as 0.09°. The performance of the described receiver module was verified in the experiments for both low- and high-field (0.5 T and 1.5 T) MRI scanners and was compared to a modern commercial MRI receiver system.

  3. Applying Digital Sensor Technology: A Problem-Solving Approach

    Science.gov (United States)

    Seedhouse, Paul; Knight, Dawn

    2016-01-01

    There is currently an explosion in the number and range of new devices coming onto the technology market that use digital sensor technology to track aspects of human behaviour. In this article, we present and exemplify a three-stage model for the application of digital sensor technology in applied linguistics that we have developed, namely,…

  4. Seismic Rayleigh Wave Digital Processing Technology

    Science.gov (United States)

    Jie, Li

    2013-04-01

    In Rayleigh wave exploration, the digital processing of data plays a very important position. This directly affects the interpretation of ground effect. Therefore, the use of accurate processing software and effective method in the Rayleigh wave exploration has important theoretical and practical significance. Previously, Rayleigh wave dispersion curve obtained by the one-dimensional phase analysis. This method requires channel spacing should be less than the effective wavelength. And minimal phase error will cause great changes in the phase velocity of Rayleigh wave. Damped least square method is a local linear model. It is easy to cause that inversion objective function cannot find the global optimal solution. Therefore, the method and the technology used in the past are difficult to apply the requirements of the current Rayleigh wave exploration. This study focused on the related technologies and algorithms of F-K domain dispersion curve extraction and GA global non-linear inversion, and combined with the impact of Rayleigh wave data acquisition parameters and the characteristics. Rayleigh wave exploration data processing software design and process technology research is completed. Firstly, the article describes the theoretical basis of Rayleigh wave method. This is also part of the theoretical basis of following treatment. The theoretical proof of existence of Rayleigh wave Dispersive in layered strata. Secondly, F-K domain dispersion curve extraction tests showed that the method can overcome the one-dimensional digital processing technology deficiencies, and make full use of multi-channel Rayleigh wave data record information. GA global non-linear inversion indicated that the inversion is not easy getting into local optimal solution. Thirdly, some examples illustrate each mode Rayleigh wave dispersion curve characteristics in the X-T domain. Tests demonstrated the impact on their extraction of dispersion curves. Parameters change example (including the X

  5. The application of digital technology in community health education

    Directory of Open Access Journals (Sweden)

    Wen Ren

    2015-01-01

    Full Text Available With the rapid development of the internet and information technologies, coupled with a variety of digital media, the digital technology has become a conventional method of health education for the general public and has the potential to influence health behaviors. Our aim was to conduct a review of how digital technology projects have been used in the health education and health promotion, as well as the disadvantages and barriers in the process.

  6. DS-CDMA Receiver Based on a Five-Port Technology

    Directory of Open Access Journals (Sweden)

    Elvino S. Sousa

    2005-07-01

    Full Text Available High data rates, low-power consumption, and low complexity will be the most important parameters in the design of the next-generation mobile terminals. In this paper we are introducing a new paradigm in the design of direct sequence spread spectrum receiver by combining analog and digital signal processing. The main difference with respect to the conventional all-digital receiver design approach is that the proposed mixed analog/digital processing results in a symbol rate sampling rather than the high-rate subchip sampling. Analog signal despreading is the key part of the proposed receiver solution, which is based on a five-port device, a passive RF square-law-type device. It is used to perform two important tasks at the same time, namely, the direct conversion and analog despreading. To achieve lower complexity, the proposed receiver uses rectangular instead of pulse-matched despreading at the cost of only a small performance degradation. Also, we propose a new noncoherent pseudonoise (PN code tracking scheme based on error signal generated through the L1 norm. This results in comparable or even better PN code tracking performance than L2 norm circuitry, using less complex hardware. Further, we explore how this technology can be applied in the design of DS-CDMA RAKE receiver for mobile terminals. Depending on how the pilot signal is multiplexed, we propose two types of RAKE receivers. It is shown that under Rayleigh fading channel such receiver structures offer robustness and high performance, while maintaining the low complexity achievable through the five-port device.

  7. Technology Scaling Impact on Embedded ADC Design for Telecom Receivers

    DEFF Research Database (Denmark)

    Nielsen, Jannik Hammel; Andreani, Pietro; Malcovati, Piero

    2005-01-01

    -frequency, medium-resolution applications. The design of a 10 bit 20 MS/s ADC using the successive approximation algorithm is presented in order to validate the presented concepts. By using a deep-submicron technology, the speed of the chosen architecture is pushed to meet the desired output rate.......This paper is concerned with the impact of technology scaling on the choice of A/D converters in telecom receivers. It is shown that the trend of diminishing feature size, together with better matching of passive components, allows the use of A/D topologies traditionally confined to low...

  8. Transitioning towards the Digital Native: Examining Digital Technologies, Video Games, and Learning

    Science.gov (United States)

    Salomon, John

    2010-01-01

    Although digital technologies have become commonplace among people who grew up around them, little is known about the effect that such technology will have on learners or its impact on traditional methods of educational delivery. This dissertation examines how certain technologies affect digital natives and seeks to understand specific…

  9. Digital technology and human development: a charter for nature conservation.

    Science.gov (United States)

    Maffey, Georgina; Homans, Hilary; Banks, Ken; Arts, Koen

    2015-11-01

    The application of digital technology in conservation holds much potential for advancing the understanding of, and facilitating interaction with, the natural world. In other sectors, digital technology has long been used to engage communities and share information. Human development-which holds parallels with the nature conservation sector-has seen a proliferation of innovation in technological development. Throughout this Perspective, we consider what nature conservation can learn from the introduction of digital technology in human development. From this, we derive a charter to be used before and throughout project development, in order to help reduce replication and failure of digital innovation in nature conservation projects. We argue that the proposed charter will promote collaboration with the development of digital tools and ensure that nature conservation projects progress appropriately with the development of new digital technologies.

  10. A Study on the Timing Technology of Digital Satellite TV

    Science.gov (United States)

    Song, K. X.

    2013-03-01

    Based on analyzing and summarizing the modern timing technologies, through intensive analyzing the characteristics of the current digital satellite TV signals, and without changing equipment configuration of the digital satellite TV transmitter and signal system, this thesis puts forward the method of using the digital TV signal to transmit the standard time and frequency, and carries out the relevant researches on the key technologies. Meanwhile, we make experiments on the digital satellite TV timing system, which are based on the proposed timing method. Through analyzing the test data, the timing method is proved practicable and with a high precision. The main research work is as follows: (1) Firstly, we summarize the necessary conditions and key elements required for timing by analyzing the characteristics of modern timing methods, and analyze China’s digital satellite TV signal system; Secondly, we propose the idea that the inherent flag bit of source coding signals of TV is used to trigger event of timing and then complete this task; Thirdly, we propose the principle of transmitting the standard time and frequency through digital satellite TV signal, analyze the error sources which affect the accuracy of timing, and find the ways to reduce the error effect. (2) Synchronization clock signal is recovered from asynchronous serial interface (ASI) data to achieve bit synchronization, so that the transmitter can accurately access to the high-precision standard time code. At the same time, the TV signal transmission delay on the transmission channel is accurately measured in order to supply the necessary information for timing. Based on the analysis of the ASI data transmission characteristics and transmission standards, a method using over-sampling to recover the ASI clock signal and synchronize the digital TV signal source coding is proposed in this paper. This method is proved effective by the implementation on the FPGA (Field Programmable Gate Array). (3) Using

  11. Poaching Museum Collections using Digital 3D Technologies

    Directory of Open Access Journals (Sweden)

    Sarah Younan

    2015-12-01

    Full Text Available This paper investigates the creative engagement with digital 3D models of museum artefacts and gives insight into new uses of museum collections enabled by digital scanning, editing and 3D printing technologies. Digital 3D models of museum artefacts are malleable and increasingly easy to use. Additionally, freely available 3D software has made 3D scanning, editing and manufacturing possible for non-specialists. These technologies allow users to create new artworks through the creation and transformation of digital replicas of museum artefacts. Examples of creative works, taken from two case studies that involve the creative use of digital reproductions of museum artefacts are presented in this paper. These projects are illustrative of a larger trend: the digital ‘poaching’ of heritage artefacts. This paper examines how digital 3D technologies can foster creative forms of museum engagement, democratise access to museum collections and engage users with personal forms of museum experience.

  12. Digital media technological and social challenges of the interactive world

    CERN Document Server

    Winget, Megan A; Aspray, William

    2011-01-01

    There has been an explosion in the creation and use of digital media over the past quarter century and in particular over the past decade. This book carefully examines multiple aspects of digital media from the different perspectives of some of the top scholars in the field. Organized into four parts, Digital Media looks at the preservation of digital media, the interaction between technological changes and cultural practices, the organization of digital media, and its history. The wealth of varied perspectives collected together in this volume provides new light on the topic of digital media.

  13. Multi-aperture digital coherent combining for free-space optical communication receivers.

    Science.gov (United States)

    Geisler, David J; Yarnall, Timothy M; Stevens, Mark L; Schieler, Curt M; Robinson, Bryan S; Hamilton, Scott A

    2016-06-13

    Space-to-ground optical communication systems can benefit from reducing the size, weight, and power profiles of space terminals. One way of reducing the required power-aperture product on a space platform is to implement effective, but costly, single-aperture ground terminals with large collection areas. In contrast, we present a ground terminal receiver architecture in which many small less-expensive apertures are efficiently combined to create a large effective aperture while maintaining excellent receiver sensitivity. This is accomplished via coherent detection behind each aperture followed by digitization. The digitized signals are then combined in a digital signal processing chain. Experimental results demonstrate lossless coherent combining of four lasercom signals, at power levels below 0.1 photons/bit/aperture.

  14. Digital Photonic Receivers for Wireless and Wireline Optical Fiber Transmission Links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil

    investigations on the performance of data-aided optical channel estimation based on constant-amplitude zero-autocorrelation (CAZAC) sequences for 112 Gb/s polarization-diversity coherent optical fiber transmission links. The benefits of introducing digital signal processing functions in optically envelope......This PhD thesis addresses the design and performance evaluation of digital photonic receivers in hybrid optical fiber-wireless transmission systems. The research results presented in this thesis are pioneering in two areas. First, it is shown the first experimental demonstration of automatic...... demodulation of signals with mixed modulation formats and bit rates in a single digital coherent photonic receiver. The demodulated signals were generated on baseband and optical phase-modulated (PM) radio-over-fiber (RoF) systems. Secondly, it is presented the first known analytical and numerical...

  15. Multi-Mode FMCW Radar Array with Independent Digital Beam Steering for Transmit and Receive

    NARCIS (Netherlands)

    Dijk, R. van; Houwen, E.H. van der; Maas, A.P.M.

    2008-01-01

    A phased-array FMCW radar has been design and built from COTS components. The generation of the frequency sweep is done by mixing a central local oscillator signal with a baseband sweep of a direct digital synthesizer (DDS). To ensure maximum flexibility the receive side has been equipped with it's

  16. [Impact of digital technology on clinical practices: perspectives from surgery].

    Science.gov (United States)

    Zhang, Y; Liu, X J

    2016-04-09

    Digital medical technologies or computer aided medical procedures, refer to imaging, 3D reconstruction, virtual design, 3D printing, navigation guided surgery and robotic assisted surgery techniques. These techniques are integrated into conventional surgical procedures to create new clinical protocols that are known as "digital surgical techniques". Conventional health care is characterized by subjective experiences, while digital medical technologies bring quantifiable information, transferable data, repeatable methods and predictable outcomes into clinical practices. Being integrated into clinical practice, digital techniques facilitate surgical care by improving outcomes and reducing risks. Digital techniques are becoming increasingly popular in trauma surgery, orthopedics, neurosurgery, plastic and reconstructive surgery, imaging and anatomic sciences. Robotic assisted surgery is also evolving and being applied in general surgery, cardiovascular surgery and orthopedic surgery. Rapid development of digital medical technologies is changing healthcare and clinical practices. It is therefore important for all clinicians to purposefully adapt to these technologies and improve their clinical outcomes.

  17. Digital Media and Technology in Afterschool Programs, Libraries, and Museums

    Science.gov (United States)

    Herr-Stephenson, Becky; Rhoten, Diana; Perkel, Dan; Sims, Christo

    2011-01-01

    Digital media and technology have become culturally and economically powerful parts of contemporary middle-class American childhoods. Immersed in various forms of digital media as well as mobile and Web-based technologies, young people today appear to develop knowledge and skills through participation in media. This MacArthur Report examines the…

  18. Digital Media and Technology in Afterschool Programs, Libraries, and Museums

    Science.gov (United States)

    Herr-Stephenson, Becky; Rhoten, Diana; Perkel, Dan; Sims, Christo

    2011-01-01

    Digital media and technology have become culturally and economically powerful parts of contemporary middle-class American childhoods. Immersed in various forms of digital media as well as mobile and Web-based technologies, young people today appear to develop knowledge and skills through participation in media. This MacArthur Report examines the…

  19. A dual-mode analog baseband with digital-assisted DC-offset calibration for WCDMA/GSM receivers

    Institute of Scientific and Technical Information of China (English)

    Xie Renzhong; Jiang Chen; Li Weinan; Huang Yumei; Hong Zhiliang

    2011-01-01

    A dual-mode analog baseband with digital-assisted DC-offsset calibration(DCOC)for WCDMA/GSM receiver is presented.A digital-assisted DCOC is proposed to solve the DC-offset problem by removing the DCoffset component only.This method has no bandwidth sacrifice.After calibration the measured output residual offset voltage is within 5 mV at most gain settings and the IIP2 is more than 60 dBm.The baseband is designed to be reconfigurable at bandwidths of 200 kHz and 2.1 MHz.Total baseband gain can be programmed from 6 to 54 dB.The chip is manufactured with 0.13 μm CMOS technology and consumes 10 mA from a 1.5 V supply in the GSM mode including an on-chip buffer while the core area occupies 1.2 mm2.

  20. Advanced laser sensing receiver concepts based on FPA technology.

    Energy Technology Data Exchange (ETDEWEB)

    Jacobson, P. L. (Phillip L.); Petrin, R. R. (Roger R.); Jolin, J. L. (John L.); Foy, B. R. (Bernard R.); Lowrance, J. L.; Renda, G. (George)

    2002-01-01

    The ultimate performance of any remote sensor is ideally governed by the hardware signal-to-noise capability and allowed signal-averaging time. In real-world scenarios, this may not be realizable and the limiting factors may suggest the need for more advanced capabilities. Moving from passive to active remote sensors offers the advantage of control over the illumination source, the laser. Added capabilities may include polarization discrimination, instantaneous imaging, range resolution, simultaneous multi-spectral measurement, or coherent detection. However, most advanced detection technology has been engineered heavily towards the straightforward passive sensor requirements, measuring an integrated photon flux. The need for focal plane array technology designed specifically for laser sensing has been recognized for some time, but advances have only recently made the engineering possible. This paper will present a few concepts for laser sensing receiver architectures, the driving specifications behind those concepts, and test/modeling results of such designs.

  1. Are Digital Natives a Myth or Reality? University Students' Use of Digital Technologies

    Science.gov (United States)

    Margaryan, Anoush; Littlejohn, Allison; Vojt, Gabrielle

    2011-01-01

    This study investigated the extent and nature of university students' use of digital technologies for learning and socialising. The findings show that students use a limited range of mainly established technologies. Use of collaborative knowledge creation tools, virtual worlds, and social networking sites was low. "Digital natives" and students of…

  2. Reducing the Digital Divide among Children Who Received Desktop or Hybrid Computers for the Home

    Directory of Open Access Journals (Sweden)

    Gila Cohen Zilka

    2016-06-01

    Full Text Available Researchers and policy makers have been exploring ways to reduce the digital divide. Parameters commonly used to examine the digital divide worldwide, as well as in this study, are: (a the digital divide in the accessibility and mobility of the ICT infrastructure and of the content infrastructure (e.g., sites used in school; and (b the digital divide in literacy skills. In the present study we examined the degree of effectiveness of receiving a desktop or hybrid computer for the home in reducing the digital divide among children of low socio-economic status aged 8-12 from various localities across Israel. The sample consisted of 1,248 respondents assessed in two measurements. As part of the mixed-method study, 128 children were also interviewed. Findings indicate that after the children received desktop or hybrid computers, changes occurred in their frequency of access, mobility, and computer literacy. Differences were found between the groups: hybrid computers reduce disparities and promote work with the computer and surfing the Internet more than do desktop computers. Narrowing the digital divide for this age group has many implications for the acquisition of skills and study habits, and consequently, for the realization of individual potential. The children spoke about self improvement as a result of exposure to the digital environment, about a sense of empowerment and of improvement in their advantage in the social fabric. Many children expressed a desire to continue their education and expand their knowledge of computer applications, the use of software, of games, and more. Therefore, if there is no computer in the home and it is necessary to decide between a desktop and a hybrid computer, a hybrid computer is preferable.

  3. Equalization of nonlinear transmission impairments by maximum-likelihood-sequence estimation in digital coherent receivers.

    Science.gov (United States)

    Khairuzzaman, Md; Zhang, Chao; Igarashi, Koji; Katoh, Kazuhiro; Kikuchi, Kazuro

    2010-03-01

    We describe a successful introduction of maximum-likelihood-sequence estimation (MLSE) into digital coherent receivers together with finite-impulse response (FIR) filters in order to equalize both linear and nonlinear fiber impairments. The MLSE equalizer based on the Viterbi algorithm is implemented in the offline digital signal processing (DSP) core. We transmit 20-Gbit/s quadrature phase-shift keying (QPSK) signals through a 200-km-long standard single-mode fiber. The bit-error rate performance shows that the MLSE equalizer outperforms the conventional adaptive FIR filter, especially when nonlinear impairments are predominant.

  4. A 3-5GHz UWB CMOS Receiver with Digital Control Technique

    DEFF Research Database (Denmark)

    Han, Bo; Liu, Mengmeng; Ge, Ning

    2010-01-01

    This article presents a CMOS receiver that works for 3-5GHz low band SC-UWB. The receiver contains PLL, Mixer, and VGA. Double down conversion is adopted in the receiver to overcome the orthogonal clock design difficulty; digital assisted RF control method is used to increase the stability....... This receiver was fabricated in SMIC01.8mmRF process with chip area of 1 × 1 mm2 ;according to measurement, this receiver has bandwidth of 500MHz; VGA control range is 30dB; IIP3 is -10dBm;IF port output is 250mVp-p; the power consumption is 36mW with supplying voltage 1.8V....

  5. Digital Natives as Preservice Teachers: What Technology Preparation Is Needed?

    Science.gov (United States)

    Lei, Jing

    2009-01-01

    This study focused on "digital natives" as preservice teachers to examine their beliefs, attitudes, and technology experiences and expertise, identify the strengths and weaknesses in their technology knowledge and skills, and explore what technology preparation was needed to prepare them to integrate technology in their future classrooms. Results…

  6. Can New Digital Technologies Support Parasitology Teaching and Learning?

    Science.gov (United States)

    Jabbar, Abdul; Gasser, Robin B; Lodge, Jason

    2016-07-01

    Traditionally, parasitology courses have mostly been taught face-to-face on campus, but now digital technologies offer opportunities for teaching and learning. Here, we give a perspective on how new technologies might be used through student-centred teaching approaches. First, a snapshot of recent trends in the higher education is provided; then, a brief account is given of how digital technologies [e.g., massive open online courses (MOOCs), flipped classroom (FC), games, quizzes, dedicated Facebook, and digital badges] might promote parasitology teaching and learning in digital learning environments. In our opinion, some of these digital technologies might be useful for competency-based, self-regulated, learner-centred teaching and learning in an online or blended teaching environment.

  7. Digital Creativity:Children’s Playful Mastery of Technology

    OpenAIRE

    Petersson Brooks, Eva; Brooks, Anthony Lewis

    2014-01-01

    This paper reports on a study exploring the outcomes from children’s play with technology in earlychildhood learning practices. The paper addresses questions related to how digital technology canfoster creativity in early childhood learning environments. It consists of an analysis of children’sinteraction with the KidSmart furniture focusing on digital creativity potentials and play valuessuggested by the technology. The study applied a qualitative approach and included125 children(aged three...

  8. 77 FR 8284 - Western Digital Technologies, Inc., Hard Drive Development Engineering Group Irvine (Formerly at...

    Science.gov (United States)

    2012-02-14

    ... workers of Western Digital Technologies, Inc., Hard Drive Development Engineering Group, Lake Forest... Western Digital Technologies, Inc., Hard Drive Development Engineering Group, Irvine (formerly at Lake... Employment and Training Administration Western Digital Technologies, Inc., Hard Drive Development...

  9. 76 FR 61746 - Western Digital Technologies, Inc.: Hard Drive Development Engineering Group Irvine (Formerly at...

    Science.gov (United States)

    2011-10-05

    ... Western Digital Technologies, Inc., Hard Drive Development Engineering Group, Lake Forest, California... workers and former workers of Western Digital Technologies, Inc., Hard Drive Development Engineering Group... Employment and Training Administration Western Digital Technologies, Inc.: Hard Drive Development...

  10. 76 FR 10403 - Western Digital Technologies, Inc., Coporate Headquaters/Hard Drive Development Division, Lake...

    Science.gov (United States)

    2011-02-24

    ... Drive Development Division, Lake Forest, California (Western Digital Technologies). The Department's... former workers of Western Digital Technologies, Inc., Corporate Headquarters/Hard Drive Development... Employment and Training Administration Western Digital Technologies, Inc., Coporate Headquaters/Hard...

  11. An Approach of Integrating Communication Services in Applications for Android-Based Digital TV Receivers

    Directory of Open Access Journals (Sweden)

    S. Jovanovic

    2013-06-01

    Full Text Available Digital TV receivers are becoming increasingly powerful devices allowing consumers to not only watch television broadcasts but also to access the Internet or communicate to other devices in the same local area network through either an Ethernet connection or by using a wireless connection. As the living room represents a meeting place for family and friends to gather and socialize in, the possibility of playing informal games using the television set as the interaction device is very attractive. This paper presents a developed application that integrates new communication capabilities of digital TV receivers running the Android OS. The application is a game showing its content overlaid on top of a television program whereas Android mobile devices are used as controllers. The performance of the application is tested by measuring the response times of the various communication services and by analyzing feedback from a selected group of users.

  12. Simple and robust symbol rate estimation method for digital coherent optical receivers

    Science.gov (United States)

    Cui, Sheng; Xia, Wenjuan; Shang, Jin; Ke, Changjian; Fu, Songnian; Liu, Deming

    2016-05-01

    A novel symbol rate estimation (SRE) technique utilizing the clock tone (CT) obtained by Godard timing recovery algorithm is proposed. By this technique, the known sampling rate of the analog-to-digital converter (ADC) in digital coherent optical receivers can used as a reference to directly determine the unknown signal symbol rate. The impact of polarization mode dispersion (PMD) on the CT magnitude can be mitigated by using the hybrid correlation function (HCF) consisting of both auto-correlation function (ACF) and cross-correlation function (XCF) of the received signal spectrum, while the chromatic dispersion (CD) impact can be mitigated by adaptive CD compensation techniques. This technique is simple, accurate, applicable to advanced modulation formats commonly used, and robust to various link impairments. Numerical simulations and experimental results are presented to validate this technique.

  13. Digital coherent receiver for phase modulated radio-over-fibre optical links

    DEFF Research Database (Denmark)

    Zibar, Darko; Yu, Xianbin; Peucheret, Christophe

    2009-01-01

    A novel digital signal processing-based coherent receiver for phase-modulated radio-over-fiber (RoF) optical links is presented and demonstrated experimentally. Error-free demodulation of 50-Mbaud binary phase-shift keying (BPSK) and quadrature phase-shift keying data signal modulated on a 5-GHz...... radio-frequency (RF) carrier is experimentally demonstrated using the proposed digital coherent receiver. Additionally, a wavelength-division-multiplexing (WDM) phase-modulated RoF optical link is experimentally demonstrated. A 3 x50 Mb/s WDM transmission of a BPSK modulated 5-GHz RF carrier is achieved...... over 25 km for the WDM channel spacing of 12.5 and 25 GHz, respectively....

  14. Low-sampling-rate ultra-wideband digital receiver using equivalent-time sampling

    KAUST Repository

    Ballal, Tarig

    2014-09-01

    In this paper, we propose an all-digital scheme for ultra-wideband symbol detection. In the proposed scheme, the received symbols are sampled many times below the Nyquist rate. It is shown that when the number of symbol repetitions, P, is co-prime with the symbol duration given in Nyquist samples, the receiver can sample the received data P times below the Nyquist rate, without loss of fidelity. The proposed scheme is applied to perform channel estimation and binary pulse position modulation (BPPM) detection. Results are presented for two receivers operating at two different sampling rates that are 10 and 20 times below the Nyquist rate. The feasibility of the proposed scheme is demonstrated in different scenarios, with reasonable bit error rates obtained in most of the cases.

  15. Digital beacon receiver for ionospheric TEC measurement developed with GNU Radio

    Science.gov (United States)

    Yamamoto, M.

    2008-11-01

    A simple digital receiver named GNU Radio Beacon Receiver (GRBR) was developed for the satellite-ground beacon experiment to measure the ionospheric total electron content (TEC). The open-source software toolkit for the software defined radio, GNU Radio, is utilized to realize the basic function of the receiver and perform fast signal processing. The software is written in Python for a LINUX PC. The open-source hardware called Universal Software Radio Peripheral (USRP), which best matches the GNU Radio, is used as a front-end to acquire the satellite beacon signals of 150 and 400 MHz. The first experiment was successful as results from GRBR showed very good agreement to those from the co-located analog beacon receiver. Detailed design information and software codes are open at the URL http://www.rish.kyoto-u.ac.jp/digitalbeacon/.

  16. Efficient MIMO-OFDM Schemes for Future Terrestrial Digital TV with Unequal Received Powers

    CERN Document Server

    Nasser, Youssef; Crussière, Matthieu; Pasquero, Oudomsack

    2008-01-01

    This article investigates the effect of equal and unequal received powers on the performances of different MIMO-OFDM schemes for terrestrial digital TV. More precisely, we focus on three types of non-orthogonal schemes: the BLAST scheme, the Linear Dispersion (LD) code and the Golden code, and we compare their performances to that of Alamouti scheme. Using two receiving antennas, we show that for moderate attenuation on the second antenna and high spectral efficiency, Golden code outperforms other schemes. However, Alamouti scheme presents the best performance for low spectral efficiency and equal received powers or when one antenna is dramatically damaged. When three antennas are used, we show that Golden code offers the highest robustness to power unbalance at the receiving side

  17. A 20 GHz low noise, low cost receiver for digital satellite communication system, ground terminal applications

    Science.gov (United States)

    Allen, Glen

    1988-01-01

    A 45 month effort for the development of a 20 GHz, low-noise, low-cost receiver for digital, satellite communication system, ground terminal applications is discussed. Six proof-of-concept receivers were built in two lots of three each. Performance was generally consistent between the two lots. Except for overall noise figure, parameters were within or very close to specification. While noise figure was specified as 3.5 dB, typical performance was measured at 3.0 to 5.5 dB, over the full temperature range of minus 30 C to plus 75 C.

  18. Digital video technology - today and tomorrow: 11th office information technology conference

    Energy Technology Data Exchange (ETDEWEB)

    Liberman, J.

    1994-10-01

    Digital video is probably computing`s fastest moving technology today. Just three years ago, the zenith of digital video technology on the PC was the successful marriage of digital text and graphics with analog audio and video by means of expensive analog laser disc players and video overlay boards. The state of the art involves two different approaches to fully digital video on computers: hardware-assisted and software-only solutions.

  19. Development of wide band digital receiver for atmospheric radars using COTS board based SDR

    Science.gov (United States)

    Yasodha, Polisetti; Jayaraman, Achuthan; Thriveni, A.

    2016-07-01

    Digital receiver extracts the received echo signal information, and is a potential subsystem for atmospheric radar, also referred to as wind profiling radar (WPR), which provides the vertical profiles of 3-dimensional wind vector in the atmosphere. This paper presents the development of digital receiver using COTS board based Software Defined Radio technique, which can be used for atmospheric radars. The developmental work is being carried out at National Atmospheric Research Laboratory (NARL), Gadanki. The digital receiver consists of a commercially available software defined radio (SDR) board called as universal software radio peripheral B210 (USRP B210) and a personal computer. USRP B210 operates over a wider frequency range from 70 MHz to 6 GHz and hence can be used for variety of radars like Doppler weather radars operating in S/C bands, in addition to wind profiling radars operating in VHF, UHF and L bands. Due to the flexibility and re-configurability of SDR, where the component functionalities are implemented in software, it is easy to modify the software to receive the echoes and process them as per the requirement suitable for the type of the radar intended. Hence, USRP B210 board along with the computer forms a versatile digital receiver from 70 MHz to 6 GHz. It has an inbuilt direct conversion transceiver with two transmit and two receive channels, which can be operated in fully coherent 2x2 MIMO fashion and thus it can be used as a two channel receiver. Multiple USRP B210 boards can be synchronized using the pulse per second (PPS) input provided on the board, to configure multi-channel digital receiver system. RF gain of the transceiver can be varied from 0 to 70 dB. The board can be controlled from the computer via USB 3.0 interface through USRP hardware driver (UHD), which is an open source cross platform driver. The USRP B210 board is connected to the personal computer through USB 3.0. Reference (10 MHz) clock signal from the radar master oscillator

  20. Advanced digital image archival system using MPEG technologies

    Science.gov (United States)

    Chang, Wo

    2009-08-01

    Digital information and records are vital to the human race regardless of the nationalities and eras in which they were produced. Digital image contents are produced at a rapid pace from cultural heritages via digitalization, scientific and experimental data via high speed imaging sensors, national defense satellite images from governments, medical and healthcare imaging records from hospitals, personal collection of photos from digital cameras. With these mass amounts of precious and irreplaceable data and knowledge, what standards technologies can be applied to preserve and yet provide an interoperable framework for accessing the data across varieties of systems and devices? This paper presents an advanced digital image archival system by applying the international standard of MPEG technologies to preserve digital image content.

  1. Digital Guided Weapons Technology. Volume 1. Digital Processor System Studies

    Science.gov (United States)

    1976-11-01

    Subsystem 4. 1. 3 LORAN Subsystem 4. 1.4 E-O Data Link Subsystem 4. 1. 5 TERCOM Subsystem 4.1.6 DME Subsystem 4. 1.7 Global Positioning System...Subsystem Block Diagram 16 Electro-Optical Data Link Subsystem Block Diagram 17 TERCOM Subsystem Block Diagram 18 GPS Subsystem Functional Flow...Processing Requirements — EO Data Link 6 Processing Requirements - TERCOM Subsystem 7 GPS Guidance Subsystem Digital Processing Requirements 8

  2. The Three-dimensional Digital Factory for Shipbuilding Technology Research

    Directory of Open Access Journals (Sweden)

    Xu Wei

    2016-01-01

    Full Text Available The three-dimensional digital factory technology research is the hotspot in shipbuilding recently. The three-dimensional digital factory technology not only focus on design the components of the product, but also discuss on the simulation and analyses of the production process.Based on the three-dimensional model, the basic data layer, application control layer and the presentation layer of hierarchical structure are established in the three-dimensional digital factory of shipbuilding in this paper. And the key technologies of three-dimensional digital factory of shipbuilding are analysed. Finally, a case study is applied and the results show that the three-dimensional digital factory will play an important role in the future.

  3. Current State of Digital Reference in Primary and Secondary Education; The Technological Challenges of digital Reference; Question Negotiation and the Technological Environment; Evaluation of Chat Reference Service Quality; Visual Resource Reference: Collaboration between Digital Museums and Digital Libraries.

    Science.gov (United States)

    Lankes, R. David; Penka, Jeffrey T.; Janes, Joseph; Silverstein, Joanne; White, Marilyn Domas; Abels, Eileen G.; Kaske, Neal; Goodrum, Abby A.

    2003-01-01

    Includes five articles that discuss digital reference in elementary and secondary education; the need to understand the technological environment of digital reference; question negotiation in digital reference; a pilot study that evaluated chat reference service quality; and collaborative digital museum and digital library reference services. (LRW)

  4. Semantic Web Technologies for Digital Libraries

    Directory of Open Access Journals (Sweden)

    Rajab Abd al-Hamed

    2007-09-01

    Full Text Available An article about the semantic web, it begins with defining the semantic web and its importance, then talks about the ontology relations, then the role of the semantic web in digital libraries, and its features which will serve digital libraries.

  5. Bridging storytelling traditions with digital technology

    Directory of Open Access Journals (Sweden)

    Melany Cueva

    2013-08-01

    Full Text Available Objective. The purpose of this project was to learn how Community Health Workers (CHWs in Alaska perceived digital storytelling as a component of the “Path to Understanding Cancer” curriculum and as a culturally respectful tool for sharing cancer-related health messages. Design. A pre-course written application, end-of-course written evaluation, and internet survey informed this project. Methods. Digital storytelling was included in seven 5-day cancer education courses (May 2009–2012 in which 67 CHWs each created a personal 2–3 minute cancer-related digital story. Participant-chosen digital story topics included tobacco cessation, the importance of recommended cancer screening exams, cancer survivorship, loss, grief and end-of-life comfort care, and self-care as patient care providers. All participants completed an end-of-course written evaluation. In July 2012, contact information was available for 48 participants, of whom 24 completed an internet survey. Results. All 67 participants successfully completed a digital story which they shared and discussed with course members. On the written post-course evaluation, all participants reported that combining digital storytelling with cancer education supported their learning and was a culturally respectful way to provide health messages. Additionally, 62 of 67 CHWs reported that the course increased their confidence to share cancer information with their communities. Up to 3 years post-course, all 24 CHW survey respondents reported they had shown their digital story. Of note, 23 of 24 CHWs also reported change in their own behaviour as a result of the experience. Conclusions. All CHWs, regardless of computer skills, successfully created a digital story as part of the cancer education course. CHWs reported that digital stories enhanced their learning and were a culturally respectful way to share cancer-related information. Digital storytelling gave the power of the media into the hands of CHWs

  6. Colloquium: Digital Technologies--Help or Hindrance for the Humanities?

    Science.gov (United States)

    Barker, Elton; Bissell, Chris; Hardwick, Lorna; Jones, Allan; Ridge, Mia; Wolffe, John

    2012-01-01

    This article offers reflections arising from a recent colloquium at the Open University on the implications of the development of digital humanities for research in arts disciplines, and also for their interactions with computing and technology. Particular issues explored include the ways in which the digital turn in humanities research is also a…

  7. Debating Digital Childhoods: Questions Concerning Technologies, Economies and Determinisms

    Science.gov (United States)

    Gibbons, Andrew

    2015-01-01

    The learning child, the child that is the object of interest through modernity and into mutated modernity, in the knowledge economy, is a digital age identity of great interest. Talk about childhood and the digital age invokes a range of questions about what is happening at this time and with these technologies and that creates more or less of a…

  8. Digital Technologies in the Museum: Same Old, Same Old?

    NARCIS (Netherlands)

    Kalle-den Oudsten, I.; Ioannides, M.; Fink, E.; Moropoulou, A.; Hagedorn-Saupe, M.; Fresa, A.; Liestøl, G.; Rajcic, V.; Grussenmeyer, P.

    2016-01-01

    Digital technologies are often said to be open, democratic, social and participatory. These qualities are also associated with the concept of the post-museum. This paper explores the use of the digital in museums. It is argued that museums often employ new media to perpetuate traditional narratives

  9. Analog Beamforming and Digital Beamforming on Receive for Range Ambiguity Suppression in Spaceborne SAR

    Directory of Open Access Journals (Sweden)

    Pingping Huang

    2015-01-01

    Full Text Available For future spaceborne synthetic aperture radar (SAR missions, digital beamforming (DBF on receive in elevation to form a sharp high receive beam will be adopted to improve the signal to noise ratio (SNR level and suppress range ambiguities. However, in some special cases, range ambiguities may be received by grating lobes with the high receive beam gain, and range ambiguities would not be well suppressed and even may be increased. In this paper, a new receiving approach based on analog beamforming (ABF and DBF is proposed. According to the spaceborne SAR imaging geometry and the selected pulse repetition frequency (PRF, the antenna patterns of all subapertures of the whole receive antenna in elevation are adjusted by ABF at first. Afterwards, signals from all subapertures in elevation are combined by a real time DBF processor onboard. Since grating lobes could be suppressed by the antenna pattern of the subapertures via ABF, range ambiguities would be well suppressed even if ambiguities are received by grating lobes. Simulation results validate the proposed approach.

  10. Building the Digital Branch A Library Technology Report

    CERN Document Server

    King, David Lee

    2009-01-01

    This issue of Library Technology Reports explores the idea of the digital branch-a library website that is a vital, functional resource for patrons and enhances the library's place within its community.

  11. Effective Use of Digital Technologies of High School Teachers as Digital Immigrants in Six Rural Public Schools

    Science.gov (United States)

    Pattee, Andy

    2012-01-01

    Problem: A widening experiential gap of effective use of technology in K-12 schools between "digital immigrants" and "digital natives" (Prensky, 2001) is becoming more evident as digital natives become classroom teachers and showcase pedagogical strategies with digital technologies. There is a dearth of research on digital…

  12. The Digital Literacy Debate: An Investigation of Digital Propensity and Information and Communication Technology

    Science.gov (United States)

    Nasah, Angelique; DaCosta, Boaventura; Kinsell, Carolyn; Seok, Soonhwa

    2010-01-01

    Research suggests students' use of information and communication technology (ICT) may be more a matter of digital literacy and access rather than a generational trait. We sought to identify ICT preferences of post-secondary students (N = 580) through a Digital Propensity Index (DPI), investigating communication methods, Internet practices and the…

  13. The Digital Literacy Debate: An Investigation of Digital Propensity and Information and Communication Technology

    Science.gov (United States)

    Nasah, Angelique; DaCosta, Boaventura; Kinsell, Carolyn; Seok, Soonhwa

    2010-01-01

    Research suggests students' use of information and communication technology (ICT) may be more a matter of digital literacy and access rather than a generational trait. We sought to identify ICT preferences of post-secondary students (N = 580) through a Digital Propensity Index (DPI), investigating communication methods, Internet practices and the…

  14. PROBLEMS AND DEVELOPMENT FEATURES OF DIGITAL BANKING TECHNOLOGIES

    OpenAIRE

    Shevchuk, T. V.

    2015-01-01

    In the paper the development level of digital technologies in different spheres of economy ofUkraineand other countries of the world, their role in enhancing the effectiveness of cashless payment settlement have been analysed. Certain factors which restrain the development of digital technologies in Ukraine, particularly in banks, have been considered. It has been determined that the main factor is the lack of such a degree of development of telecommunications infrastructure. The state, condi...

  15. The introduction of digital dental technology into BDS curricula.

    Science.gov (United States)

    Chatham, C; Spencer, M H; Wood, D J; Johnson, A

    2014-12-05

    The aim of this study was to determine the degree to which digital dental technologies have been introduced into the curricula of UK dental schools. A survey was carried out of all the UK dental schools that teach undergraduate dental students. The survey contained six questions and was designed to determine if digital dental technology techniques or systems were being taught in the curricula, what these techniques were, and whether the school dental laboratories supported these techniques. Sixteen schools were surveyed and 11 replied: a response rate of 69%. Forty-five percent of the schools that replied did not teach digital dental technology in their curriculum. Of the 55% of schools who did teach digital dental technology, 50% gave lectures or demonstrations while the other 50% allowed practical involvement by the student. Two thirds of these stated that not all the students participated in practical usage. Seventy-three percent of the schools that replied had dental laboratories using some, but not all the digital dental technology techniques listed. Eighty percent of the schools that were not teaching digital dental technology said it was because it was not included in the curriculum, and 20% stated it was due to a lack of technical expertise or support.

  16. Digital management technology and its application to investment casting enterprises

    Directory of Open Access Journals (Sweden)

    Xiao-yuan Ji

    2016-09-01

    Full Text Available With the advent of Industry 4.0, more and more investment casting enterprises are implementing production manufacturing systems, especially in the last two years. This paper summarizes three new common requirements of the digital management aspect in precision casting enterprises, and puts forward three corresponding techniques. They are: the production process tracking card technology based on the main-sub card mode; the workshop site production process processing technology based on the barcode; and the equipment data integration technology. Then, this paper discusses in detail the principle, application and effect of these technologies; to provide the reference for enterprises to move towards digital casting and intelligent casting.

  17. Digital technologies in museums: New routes to engagement and participation’

    Directory of Open Access Journals (Sweden)

    Carey Jewitt

    2012-12-01

    Full Text Available A multimodal semiotic approach is applied in this chapter to three examples to illustrate how the use of digital technology in museums and galleries can re-mediated the visitor experience (Jewitt, 2009; Kress, 2009. The examples are selected to expand upon the themes raised in Chapter X. They each explore different technologies, contexts and purposes and to illustrate the successful use of digital technology in exhibitions, galleries, or interventions: 1. You Tube and Flickr: The Weather Project by Olafur Eliasson at the Tate Modern Museum; 2. Interactive artefacts, virtual tours and Websites: The Winston Churchill Museum; 3. Mobile Technologies: OOLK at the D-Day museum

  18. Health behavior models for informing digital technology interventions for individuals with mental illness.

    Science.gov (United States)

    Naslund, John A; Aschbrenner, Kelly A; Kim, Sunny Jung; McHugo, Gregory J; Unützer, Jürgen; Bartels, Stephen J; Marsch, Lisa A

    2017-09-01

    Theoretical models offer valuable insights for designing effective and sustainable behavioral health interventions, yet the application of theory for informing digital technology interventions for people with mental illness has received limited attention. We offer a perspective on the importance of applying behavior theories and models to developing digital technology interventions for addressing mental and physical health concerns among people with mental illness. In this commentary, we summarize prominent theories of human behavior, highlight key theoretical constructs, and identify opportunities to inform digital health interventions for people with mental illness. We consider limitations with existing theories and models, and examine recent theoretical advances that can specifically guide development of digital technology interventions. Established behavioral frameworks including health belief model, theory of planned behavior, transtheoretical model, and social cognitive theory consist of important and overlapping constructs that can inform digital health interventions for people with mental illness. As digital technologies continue to evolve and enable longitudinal data collection, real-time behavior monitoring, and adaptive features tailored to users' changing needs over time, there are new opportunities to broaden our understanding of health behaviors and mechanisms of behavior change. Recent advances include dynamic models of behavior, persuasive system design, the behavioral intervention technology model, and behavioral models for just-in-time adaptive interventions. Behavior theories offer advantages for guiding use of digital technologies. Future researchers must explore how theoretical models can effectively advance efforts to develop, evaluate, and disseminate digital health interventions targeting individuals with mental illness. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  19. Digital Library of Expert System Based at Indonesia Technology University

    Directory of Open Access Journals (Sweden)

    Dewa Gede Hendra Divayana

    2015-03-01

    Full Text Available Digital library is a very interesting phenomenon in the world of libraries. In this era of globalization, the digital library is needed by students, faculty, and the community in the search for quick reference through internet access, so that students, faculty, and the community does not have to come directly to the library. Accessing collections of digital libraries can also be done anytime and anywhere. Digital Library development also occurred at Indonesia Technology University. That University offers a digital library based of expert system. The concept of digital library is utilizing science expert system in the process of cataloging and searching digital collections. By using this digital library based of expert system, users can search the collection, reading collection, and download the desired collection by online system. The digital library based of expert system at Indonesia Technology University is built using the PHP programming language, MySQL database as a data base management system, and developed the method of forward chaining and backward chaining as inference engine.

  20. Digital video and audio broadcasting technology a practical engineering guide

    CERN Document Server

    Fischer, Walter

    2010-01-01

    Digital Video and Audio Broadcasting Technology - A Practical Engineering Guide' deals with all the most important digital television, sound radio and multimedia standards such as MPEG, DVB, DVD, DAB, ATSC, T-DMB, DMB-T, DRM and ISDB-T. The book provides an in-depth look at these subjects in terms of practical experience. In addition it contains chapters on the basics of technologies such as analog television, digital modulation, COFDM or mathematical transformations between time and frequency domains. The attention in the respective field under discussion is focussed on aspects of measuring t

  1. Materialist Perspectives on Digital Technologies: Informing Debates on Digital Literacy and Competence

    OpenAIRE

    2016-01-01

    Publisher's version, source: http://doi.org/10.1515/nor-2016-0006. The present article brings critical media research and science and technology studies (STS) into dialogue with approaches to digital literacy and digital competencies in educational contexts. In particular, it focuses on material aspects of new information and communication technologies (ICTs) such as technical infrastructure, economic conditions, ecological consequences, and code-based as well as embodied forms of impact, ...

  2. Nonparametric TOA estimators for low-resolution IR-UWB digital receiver

    Institute of Scientific and Technical Information of China (English)

    Yanlong Zhang; Weidong Chen

    2015-01-01

    Nonparametric time-of-arrival (TOA) estimators for im-pulse radio ultra-wideband (IR-UWB) signals are proposed. Non-parametric detection is obviously useful in situations where de-tailed information about the statistics of the noise is unavailable or not accurate. Such TOA estimators are obtained based on condi-tional statistical tests with only a symmetry distribution assumption on the noise probability density function. The nonparametric es-timators are attractive choices for low-resolution IR-UWB digital receivers which can be implemented by fast comparators or high sampling rate low resolution analog-to-digital converters (ADCs), in place of high sampling rate high resolution ADCs which may not be available in practice. Simulation results demonstrate that nonparametric TOA estimators provide more effective and robust performance than typical energy detection (ED) based estimators.

  3. How do digital platforms for ideas, technologies, and knowledge transfer act as enablers for digital transformation?

    DEFF Research Database (Denmark)

    Hossain, Mokter; Lassen, Astrid Heidemann

    2017-01-01

    for research and development (R&D), idea generation, prediction, freelance work, peer production, co-creation, product design, and public engagement, to name but a few. For example, Dell’s IdeaStorm (Hossain & Islam, 2015a) and Starbucks’ MyStarbucksIdea (Hossain & Islam, 2015b) are two digital crowdsourcing...... are undertaking today (Berman, 2012). Despite the high significance of various digital platforms, there is limited knowledge in the extant literature about the effect of digital platforms on the organization. Thus, here we discuss how digital platforms for ideas, technologies, and knowledge transfer act...

  4. Vicious cycles: digital technologies and determinants of health in Australia.

    Science.gov (United States)

    Baum, Fran; Newman, Lareen; Biedrzycki, Katherine

    2014-06-01

    Digital technologies are increasingly important as ways to gain access to most of the important social determinants of health including employment, housing, education and social networks. However, little is known about the impact of the new technologies on opportunities for health and well-being. This paper reports on a focus group study of the impact of these technologies on people from low socio-economic backgrounds. We use Bourdieu's theories of social inequities and the ways in which social, cultural and economic capitals interact to reinforce and reproduce inequities to examine the ways in which digital technologies are contributing to these processes. Six focus group discussions with 55 people were held to examine their access to and views about using digital technologies. These data are analysed in light of Bourdieu's theory to determine how people's existing capitals shape their access to and use of digital technologies and what the implications of exclusion from the technologies are likely to be for the social determinants of health. The paper concludes that some people are being caught in a vicious cycle whereby lack of digital access or the inability to make beneficial use reinforces and amplifies existing disadvantage including low levels of reading and writing literacy. The paper concludes with a consideration of actions health promoters could take to interrupt this cycle and so contribute to reducing health inequities.

  5. Digital literacy and problem solving in technology-rich environments

    Directory of Open Access Journals (Sweden)

    Vesna Dolničar

    2015-07-01

    Full Text Available Rapid development and progress, as well as the growing presence of information and communications technologies dictate the need for more highly developed digital skills in individuals. The paper focuses on the concepts of digital skills and problem solving in technology-rich environments. It examines these on the basis of empirical data obtained in the international study PIAAC. The introductory part presents an overview of the literature and the results of previous research in the field of measurement of digital skills, and data on the use of information society services among the EU Member States. The second part of the article refers to the results obtained in the study PIAAC. The results, confirmed by the results of other studies, showed the impact of age and education level on the problem solving in technology-rich environments. Article concludes with suggestions for improving the current state of integration of all population groups in training programs in the field of digital skills.

  6. Digital Technology in Science by Doing

    Science.gov (United States)

    Bothun, G.

    1998-05-01

    In partnernship with a pilot program of K12 teachers, we are significantly reshaping the traditional manner which astronomy is taught. Our focus is to incoporate the use of modern digital detectors and data analysis directly into the curriculum. The main goal of this project is to allow students to do real observations, either by remote observation with the Pine Mountain Observatory (PMO) 1-m telescope, or by accessing the HST digital archive. To assist students with data reduction we will provide them with JAVA reduction tools already under development. We will also train teachers on how to use this digital machinery in an effective manner so as to activate the innate curiosity of students and to instill in them an appreciation for the process of science. Our project will emphasize active student experimentation and collaboration (through coordinated observations). All results and observations will be maintained and archived on the Web server in residence at PMO.

  7. Performance Evaluation of Digital Coherent Receivers for Phase-Modulated Radio-Over-Fiber Links

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Zibar, Darko; Tafur Monroy, Idelfonso

    2011-01-01

    The performance of optical phase-modulated (PM) radio-over-fiber (RoF) links assisted with coherent detection and digital signal processing (PM-Coh) is analyzed and experimentally demonstrated for next-generation wireless-over-fiber systems. PM-Coh offers high linearity for transparent transport......-bandwidth electronics. Analytical assessment and simulations are used to determine the ultimate performance with respect to laser linewidth, modulation index, and receiver sensitivity. Then, two different scenarios are studied and experimentally demonstrated as an application of PM-Coh links: a high...

  8. Developing Digital Technologies for Undergraduate University Mathematics

    DEFF Research Database (Denmark)

    Triantafyllou, Eva; Timcenko, Olga

    2013-01-01

    Our research effort presented in this paper relates with developing digital tools for mathematics education at undergraduate university level. It focuses specifically on studies where mathematics is not a core subject but it is very important in order to cope with core subjects. For our design, we...... at Aalborg University Copenhagen. Then we conducted focus groups with students where they reflected on the introduction of these applets and proposed ways to improve them or alternative ways to present the specific part of the curriculum. At the same time, we conducted observations of teachers and students...... requirements for the development of digital tools that support mathematics teaching and learning at university level....

  9. Technological Implications for Assessment Ecosystems: Opportunities for Digital Technology to Advance Assessment

    Science.gov (United States)

    Behrens, John T.; DiCerbo, Kristen E.

    2014-01-01

    Background: It would be easy to think the technological shifts in the digital revolution are simple incremental progressions in societal advancement. However, the nature of digital technology is resulting in qualitative differences in nearly all parts of daily life. Purpose: This paper investigates how the new possibilities for understanding,…

  10. Digital airborne camera introduction and technology

    CERN Document Server

    Sandau, Rainer

    2014-01-01

    The last decade has seen great innovations on the airborne camera. This book is the first ever written on the topic and describes all components of a digital airborne camera ranging from the object to be imaged to the mass memory device.

  11. A Three-Dimensional Position Architecture Using Digital TDE Receiver and Cylindrical Array Antenna

    Directory of Open Access Journals (Sweden)

    J. Mar

    2013-03-01

    Full Text Available The robust three-dimensional position architecture is proposed in the paper, where the hybrid time difference of arrival(TDOA and direction of arrival (DOA position system was designed to backup the four-station TDOA positionsystem. The digital time delay estimation (TDE receiver is used for TDOA measurement and the cylindrical arrayantenna is used for DOA measurement. The general formula of linear phase compensation for cylindrical arrayantenna in horizontal plane is derived. The detection probability of the TDE receiver and the circular error probability(CEP of the position systems over Rayleigh fading channel were numerically computed in three-dimensional space.Simulations indicate that the position accuracy of the four-station TDOA position system is degraded but the locationfunction can be retained by the hybrid TDOA and DOA position system when any one of four-stations is out of work.

  12. Next generation digital microfluidic technology: Electrophoresis of charged droplets

    Energy Technology Data Exchange (ETDEWEB)

    Im, Do Jin [Pukyong National University, Busan (Korea, Republic of)

    2015-06-15

    Contact charging of a conducting droplet in a dielectric medium is introduced as a novel and useful digital microfluidic technology as well as an interesting scientific phenomenon. The history of this phenomenon, starting from original observations to its interpretations and applications, is presented. The basic principle of the droplet contact charging is also presented. Several fundamental aspects of the droplet contact charging from view points of electrochemistry, surface science, electrocoalescence, and electrohydrodynamics are mentioned. Some promising results for future applications and potential features as a next generation digital microfluidic technology are discussed, especially for 3D organ printing. Finally, implications and significance of the proposed technology for chemical engineering community are discussed.

  13. Applications of digital IF receivers and under-sampling technique in ladar

    Science.gov (United States)

    Song, Zhi-yuan; Zhu, Shao-lan; Dong, Li-jun; Feng, Li; He, Hao-dong

    2011-06-01

    The traditional technique of phase laser range finder is mixing high frequency signals with analog circuits and filtering them to obtain the useful signal with low frequency. But the analog mixing circuits are susceptible to interference and will bring amplitude attenuation, phase jitter and offset and this way has difficulties in achieving high precision ranging and fast speed ranging at the same time. The method of this paper is based on under-sampling technique with digital synchronous detection and referring to Digital down converter technique of digital IF receiver in radar system. This method not only reduces the complexity of data processing, improves the speed and accuracy of phase detection at the same time, but also reduces requirements for ADC devices and DSP chips in the ladar system by a lower sampling rate. At the same time, the structure of electronic system is global simplified compared with traditional analog ladar system and the anti-jamming is greatly enhanced. So this method has important research value.

  14. 76 FR 32373 - In the Matter of Certain Electronic Devices Having a Digital Television Receiver and Components...

    Science.gov (United States)

    2011-06-06

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION In the Matter of Certain Electronic Devices Having a Digital Television Receiver and Components Thereof; Notice of Institution of Investigation AGENCY: U.S. International Trade Commission....

  15. Application of Cloud Technology in Digital Library

    Directory of Open Access Journals (Sweden)

    D Kishore Kumar

    2012-05-01

    Full Text Available Libraries may soon be building and managing their own data centers. This model would letlibraries maintain more control over the applications and data stores that containsensitive, private information about patrons. Provisioning and maintenance of infrastructure forWeb based digital library present several challenges. In this paper we discuss problems facedwith digital library and development efforts to overcome that problem. Infrastructure virtualizationand cloud computing are particularly attractive choices which is challenged by both growth inthe size of the indexed document collection, new features and most prominently usage. With thepurpose of applying Cloud Computing to university library, the paper describes the currentstatus of user service models in university libraries. Then it proposed to improve current userservice model with Cloud Computing. This paper explores some of the security issuessurrounding data location, mobility and availability.

  16. Technology research for digital flight control

    Science.gov (United States)

    Carestia, R. A.

    1983-01-01

    The use of advanced digital systems for flight control and guidance for a specific mission is investigated. The research areas include advanced electronic system architectures, tests with the global positioning system (GPS) in a helicopter, and advanced integrated systems concept for rotorcraft. Emphasis is on a search and rescue mission, differential global positioning systems to provide a data base of performance information for navigation, and a study to determine the present usage and trends of microcomputers and microcomputer components in the avionics industries.

  17. Review and Prospect of Cobalt-60 Digital Radiography Inspection Technology

    OpenAIRE

    AN Ji-gang

    2015-01-01

    This article is a review and prospect of the research, development and industrialization of Cobalt-60 digital radiography inspection technology based on the national requirements in the recent 20 years, which is leaded by Institute of Nuclear and New Energy Technology (INET) of TsinghuaUniversity. The research purpose, innovative approach and main academic achievements of this technology were described systematically. The industrial equipment varieties, performance, running condition and appl...

  18. Digital Technologies and performative pedagogies: Repositioning the visual

    OpenAIRE

    Kathryn Grushka; Debra Donnelly

    2010-01-01

    Images are becoming a primary means of information presentation in the digitized global media and digital technologies have emancipated and democratized the image. This allows for the reproduction and manipulation of images on a scale never seen before and opens new possibilities for teachers schooled in critical visuality. This paper reports on an innovative pre-service teacher training course in which a cross-curricula cohort of secondary teachers employed visual performative competencies t...

  19. Documentation of surgical specimens using digital video technology.

    Science.gov (United States)

    Melín-Aldana, Héctor; Carter, Barbara; Sciortino, Debra

    2006-09-01

    Digital technology is commonly used for documentation of specimens in anatomic pathology and has been mainly limited to still photographs. Technologic innovations, such as digital video, provide additional, in some cases better, options for documentation. To demonstrate the applicability of digital video to the documentation of surgical specimens. A Canon Elura MC40 digital camcorder was used, and the unedited movies were transferred to a Macintosh PowerBook G4 computer. Both the camcorder and specimens were hand-held during filming. The movies were edited using the software iMovie. Annotations and histologic photographs may be easily incorporated into movies when editing, if desired. The finished movies are best viewed in computers which contain the free program QuickTime Player. Movies may also be incorporated onto DVDs, for viewing in standard DVD players or appropriately equipped computers. The final movies are on average 2 minutes in duration, with a file size between 2 and 400 megabytes, depending on the intended use. Because of file size, distribution is more practical via CD or DVD, but movies may be compressed for distribution through the Internet (e-mail, Web sites) or through internal hospital networks. Digital video is a practical, easy, and affordable methodology for specimen documentation, permitting a better 3-dimensional understanding of the specimens. Discussions with colleagues, student education, presentation at conferences, and other educational activities can be enhanced with the implementation of digital video technology.

  20. Integrating Digital Technologies in Teaching Learning Process

    Science.gov (United States)

    Nagarajan, R.; Velmanirajan, K.; Kanna, K. Sankesh

    2013-01-01

    India has made impressive strides in the application of information and communication technology in recent years and this has reflected in a vibrant and fast growing economy. It is now an acknowledged world leader in the knowledge industry. In this paper an attempt is made to highlight the role of Information and Communication Technology (ICT) in…

  1. Educational Perspectives on Digital Communications Technologies

    Science.gov (United States)

    Brett, Clare

    2009-01-01

    This article examines key issues in how new technologies are impacting upon how we teach, learn and collaborate, and uses an educational research project called GRAIL (Graduate Researcher's Academic Identity Online) under development to illustrate some fundamental issues in adopting new technologies. A significant challenge to the effective use of…

  2. Method and apparatus for a single channel digital communications system. [synchronization of received PCM signal by digital correlation with reference signal

    Science.gov (United States)

    Couvillon, L. A., Jr.; Carl, C.; Goldstein, R. M.; Posner, E. C.; Green, R. R. (Inventor)

    1973-01-01

    A method and apparatus are described for synchronizing a received PCM communications signal without requiring a separate synchronizing channel. The technique provides digital correlation of the received signal with a reference signal, first with its unmodulated subcarrier and then with a bit sync code modulated subcarrier, where the code sequence length is equal in duration to each data bit.

  3. Digital tapped delay lines for HWIL testing of matched filter radar receivers

    Science.gov (United States)

    Olson, Richard F.; Braselton, William J.; Mohlere, Richard D.

    2009-05-01

    Matched filter processing for pulse compression of phase coded waveforms is a classic method for increasing radar range measurement resolution. A generic approach for simulating high resolution range extended radar scenes in a Hardware in the Loop (HWIL) test environment is to pass the phase coded radar transmit pulse through an RF tapped delay line comprised of individually amplitude- and phase-weighted output taps. In the generic approach, the taps are closely spaced relative to time intervals equivalent to the range resolution of the compressed radar pulse. For a range-extended high resolution clutter scene, the increased number of these taps can make an analog implementation of an RF tapped delay system impractical. Engineers at the U.S. Army Aviation and Missile Research, Development and Engineering Center (AMRDEC) have addressed this problem by transferring RF tapped delay line signal operations to the digital domain. New digital tapped delay line (DTDL) systems have been designed and demonstrated which are physically compact compared to analog RF TDLs, leverage low cost FPGA and data converter technology, and may be readily expanded using open slots in a VME card cage. In initial HWIL applications, the new DTDLs have been shown to produce better dynamic range in pulse compressed range profiles than their analog TDL predecessors. This paper describes the signal requirements and system architecture for digital tapped delay lines. Implementation, performance, and HWIL simulation integration issues for AMRDEC's first generation DTDLs are addressed. The paper concludes with future requirements and plans for ongoing DTDL technology development at AMRDEC.

  4. Technology Development for the Caltech Submillimeter Observatory Balanced Receivers

    CERN Document Server

    Kooi, J W; Monje, R; Force, B; Miller, D; Phillips, T G

    2012-01-01

    The Caltech Submillimeter Observatory (CSO) is located on top of Mauna Kea, Hawaii, at an altitude of 4.2 km. The existing suite of facility heterodyne receivers covering the submillimeter band is rapidly aging and in need of replacement. To facilitate deep integrations and automated spectral line surveys, a family of remote programmable, synthesized, dual-frequency balanced receivers covering the astronomical important 180 - 720 GHz atmospheric windows is in an advanced stage of development. Installation of the first set of receivers is expected in the spring of 2012. Dual-frequency observation will be an important mode of operation offered by the new facility instrumentation. Two band observations are accomplished by separating the H and V polarizations of the incoming signal and routing them via folded optics to the appropriate polarization sensitive balanced mixer. Scientifically this observation mode facilitates pointing for the higher receiver band under mediocre weather conditions and a doubling of sci...

  5. 数字省建设技术体系研究%Technology Framework of Digital Province

    Institute of Scientific and Technical Information of China (English)

    池天河; 王雷; 王钦敏; 陈崇成

    2003-01-01

    The construction of Digital Province and Digital City is the base and important factor of Digital Earth. During the construction of Digital Province,the technology framework of digital province is one of the key problems. This paper summarizes current construction status of digital province technology framework and content and key technology of digital fujian.

  6. Streaming and digital media understanding the business and technology

    CERN Document Server

    Rayburn, Dan

    2007-01-01

    Steaming and Digital Media gives you a concise and direct analysis to understand a scalable, profitable venture, as well as the common and hidden pitfalls to avoid in your business. By focusing on both the business implications and technical differences between online video and traditional broadcast distribution, you will learn how to gain significant time-to-market and cost-saving advantages by effectively using streaming and digital media technologies. As part of the NAB Executive Technology Briefing series, the book is geared towards the manager or executive and no technical prerequisite is

  7. Using immersive media and digital technology to communicate Earth Science

    Science.gov (United States)

    Kapur, Ravi

    2016-04-01

    A number of technologies in digital media and interactivity have rapidly advanced and are now converging to enable rich, multi-sensoral experiences which create opportunities for both digital art and science communication. Techniques used in full-dome film-making can now be deployed in virtual reality experiences; gaming technologies can be utilised to explore real data sets; and collaborative interactivity enable new forms of public artwork. This session will explore these converging trends through a number of emerging and forthcoming projects dealing with Earth science, climate change and planetary science.

  8. Technology tools to support reading in the digital age.

    Science.gov (United States)

    Biancarosa, Gina; Griffiths, Gina G

    2012-01-01

    Advances in digital technologies are dramatically altering the texts and tools available to teachers and students. These technological advances have created excitement among many for their potential to be used as instructional tools for literacy education. Yet with the promise of these advances come issues that can exacerbate the literacy challenges identified in the other articles in this issue. In this article Gina Biancarosa and Gina Griffiths characterize how literacy demands have changed in the digital age and how challenges identified in other articles in the issue intersect with these new demands. Rather than seeing technology as something to be fit into an already crowded education agenda, Biancarosa and Griffiths argue that technology can be conceptualized as affording tools that teachers can deploy in their quest to create young readers who possess the higher levels of literacy skills and background knowledge demanded by today's information-based society. Biancarosa and Griffiths draw on research to highlight some of the ways technology has been used to build the skills and knowledge needed both by children who are learning to read and by those who have progressed to reading to learn. In their review of the research, Biancarosa and Griffiths focus on the hardware and software used to display and interface with digital text, or what they term e-reading technology. Drawing on studies of e-reading technology and computer technology more broadly, they also reflect on the very real, practical challenges to optimal use of e-reading technology. The authors conclude by presenting four recommendations to help schools and school systems meet some of the challenges that come with investing in e-reading technology: use only technologies that support Universal Design for Learning; choose evidence-based tools; provide technology users with systemic supports; and capitalize on the data capacities and volume of information that technology provides.

  9. Multi-DSP and FPGA based Multi-channel Direct IF/RF Digital receiver for atmospheric radar

    Science.gov (United States)

    Yasodha, Polisetti; Jayaraman, Achuthan; Kamaraj, Pandian; Durga rao, Meka; Thriveni, A.

    2016-07-01

    Modern phased array radars depend highly on digital signal processing (DSP) to extract the echo signal information and to accomplish reliability along with programmability and flexibility. The advent of ASIC technology has made various digital signal processing steps to be realized in one DSP chip, which can be programmed as per the application and can handle high data rates, to be used in the radar receiver to process the received signal. Further, recent days field programmable gate array (FPGA) chips, which can be re-programmed, also present an opportunity to utilize them to process the radar signal. A multi-channel direct IF/RF digital receiver (MCDRx) is developed at NARL, taking the advantage of high speed ADCs and high performance DSP chips/FPGAs, to be used for atmospheric radars working in HF/VHF bands. Multiple channels facilitate the radar t be operated in multi-receiver modes and also to obtain the wind vector with improved time resolution, without switching the antenna beam. MCDRx has six channels, implemented on a custom built digital board, which is realized using six numbers of ADCs for simultaneous processing of the six input signals, Xilinx vertex5 FPGA and Spartan6 FPGA, and two ADSPTS201 DSP chips, each of which performs one phase of processing. MCDRx unit interfaces with the data storage/display computer via two gigabit ethernet (GbE) links. One of the six channels is used for Doppler beam swinging (DBS) mode and the other five channels are used for multi-receiver mode operations, dedicatedly. Each channel has (i) ADC block, to digitize RF/IF signal, (ii) DDC block for digital down conversion of the digitized signal, (iii) decoding block to decode the phase coded signal, and (iv) coherent integration block for integrating the data preserving phase intact. ADC block consists of Analog devices make AD9467 16-bit ADCs, to digitize the input signal at 80 MSPS. The output of ADC is centered around (80 MHz - input frequency). The digitized data is fed

  10. Bringing Superconductor Digital Technology to the Market Place

    Science.gov (United States)

    Nisenoff, Martin

    The unique properties of superconductivity can be exploited to provide the ultimate in electronic technology for systems such as ultra-precise analogue-to-digital and digital-to-analogue converters, precise DC and AC voltage standards, ultra high speed logic circuits and systems (both digital and hybrid analogue-digital systems), and very high throughput network routers and supercomputers which would have superior electrical performance at lower overall electrical power consumption compared to systems with comparable performance which are fabricated using conventional room temperature technologies. This potential for high performance electronics with reduced power consumption would have a positive impact on slowing the increase in the demand for electrical utility power by the information technology community on the overall electrical power grid. However, before this technology can be successfully brought to the commercial market place, there must be an aggressive investment of resources and funding to develop the required infrastructure needed to yield these high performance superconductor systems, which will be reliable and available at low cost. The author proposes that it will require a concerted effort by the superconductor and cryogenic communities to bring this technology to the commercial market place or make it available for widespread use in scientific instrumentation.

  11. Research for the Dynamic Range and Its Extension of Digital Intermediate Frequency Receiver

    Institute of Scientific and Technical Information of China (English)

    曹鹏; 齐伟; 费元春

    2004-01-01

    For the optimization of dynamic range and bandwidth of digital intermediate frequency receiver(DIFR), main factors affecting them and their relationships are studied. Firstly, the DIFR sensitivity, bandwidth, noise factor of radio frequency (RF) analog front-end (RFAF), and processing gain of intermediate frequency(IF) sampling are analyzed. Secondly, the constraint relationship of the noise factor of RFAF, the signal-to-noise ratio of ADC and the dynamic range of DIFR are studied. The relationship between the dynamic range and the RFAF gain, and that of the extended dynamic range and the RF AGC(automatic gain control) step are educed and simulated. These results can be used as theory foundations and design references for the implementation and optimization of the large dynamic range and wideband DIFR.

  12. Adaptive digital calibration techniques for narrow band low-IF receivers with on-chip PLL

    Institute of Scientific and Technical Information of China (English)

    Li Juan; Zhang Huajiang; Zhao Feng; Hong Zhiliang

    2009-01-01

    Digital calibration and control techniques for narrow band integrated low-IF receivers with on-chip frequency synthesizer are presented. The calibration and control system, which is adopted to ensure an achievable signal-to-noise ratio and bit error rate, consists of a digitally controlled, high resolution dB-linear automatic gain control (AGC), an inphase (I) and quadrature (Q) gain and phase mismatch calibration, and an automatic frequency calibration (AFC) of a wideband voltage-controlled oscillator in a PLL based frequency synthesizer. The calibration system has a low design complexity with little power and small die area. Simulation results show that the calibration system can enlarge the dynamic range to 72 dB and minimize the phase and amplitude imbalance between I and Q to 0.08° and 0.024 dB, respectively, which means the image rejection ratio is better than 60 dB. In addition, the calibration time of the AFC is 1.12μs only with a reference clock of 100 MHz.

  13. Digital video technologies and their network requirements

    Energy Technology Data Exchange (ETDEWEB)

    R. P. Tsang; H. Y. Chen; J. M. Brandt; J. A. Hutchins

    1999-11-01

    Coded digital video signals are considered to be one of the most difficult data types to transport due to their real-time requirements and high bit rate variability. In this study, the authors discuss the coding mechanisms incorporated by the major compression standards bodies, i.e., JPEG and MPEG, as well as more advanced coding mechanisms such as wavelet and fractal techniques. The relationship between the applications which use these coding schemes and their network requirements are the major focus of this study. Specifically, the authors relate network latency, channel transmission reliability, random access speed, buffering and network bandwidth with the various coding techniques as a function of the applications which use them. Such applications include High-Definition Television, Video Conferencing, Computer-Supported Collaborative Work (CSCW), and Medical Imaging.

  14. Design and implementation of the optical fiber control and transmission module in multi-channel broadband digital receiver

    Science.gov (United States)

    Zhao, Ying-xiao; Zhang, Yue; Fan, Li-jie; Li, Wei-xing; Chen, Zeng-ping

    2014-09-01

    An optical fiber control and transmission module is designed and realized based on Virtex-7 field programmable gata array (FPGA), which can be applied in multi-channel broadband digital receivers. The module consists of sampling data transfer submodule and multi-channel synchronous sampling control submodule. The sampling data transmission in 4× fiber link channel is realized with the self-defined transfer protocol. The measured maximum data rate is 4.97 Gbyte/s. By connecting coherent clocks to the transmitter and receiver endpoints and using the self-defined transfer protocol, multi-channel sampling control signals transferred in optical fibers can be received synchronously by each analog-to-digital converter (ADC) with high accuracy and strong anti-interference ability. The module designed in this paper has certain reference value in increasing the transmission bandwidth and the synchronous sampling accuracy of multi-channel broadband digital receivers.

  15. Canadian community pharmacists' use of digital health technologies in practice.

    Science.gov (United States)

    Leung, Valerie; Tharmalingam, Sukirtha; Cooper, Janet; Charlebois, Maureen

    2016-01-01

    In 2010, a pan-Canadian study on the current state and benefits of provincial drug information systems (DIS) found that substantial benefits were being realized and that pharmacists perceived DIS to be a valuable tool in the evolving models of pharmacy practice. To understand changes in digital health and the impact on practice since that time, a survey of community pharmacists in Canada was conducted. In 2014, Canada Health Infoway (Infoway) and the Canadian Pharmacists Association (CPhA) invited community pharmacists to participate in a Web-based survey to understand their use and perceived benefits of digital health in practice. The survey was open from April 15 to May 12, 2014. Of the 447 survey responses, almost all used some form of digital health in practice. Those with access to DIS and provincial laboratory information systems (LIS) reported increased productivity and better quality of care. Those without access to these systems would overwhelmingly like access. There have been significant advances in digital health and community pharmacy practice over the past several years. In addition to digital health benefits in the areas of productivity and quality of care, pharmacists are also experiencing substantial benefits in areas related to recently expanded scope of practice activities such as ordering lab tests. Community pharmacists frequently use digital health in practice and recognize the benefits of these technologies. Digital health is, and will continue to be, a key enabler for practice transformation and improved quality of care. Can Pharm J (Ott) 2016;149:xx-xx.

  16. 78 FR 36547 - Technological Advisory Council Recommendation for Improving Receiver Performance

    Science.gov (United States)

    2013-06-18

    ... COMMISSION Technological Advisory Council Recommendation for Improving Receiver Performance AGENCY: Federal... recommendations on avoiding obstacles posed by receiver performance to making spectrum available for new services... paper and its recommendations to help determine what next steps may be appropriate. The...

  17. GlossmarkTM Technology:An Innovative Digital Watermark

    Institute of Scientific and Technical Information of China (English)

    Beilei Xu; Shen-ge Wang; Chuheng Liu

    2004-01-01

    GlossmarkTM technology is a digital watermark process that embeds a visually striking gloss image within a high quality color print without the need of special papers or toners. It utilizes the angular dependence of gloss to create a differential-gloss image through the modulation of halftone structures. Both the primary image and the embedded GlossmarkTM image can be distinctively viewed from different perspectives with little interference. The strong directional nature of the gloss and the subtle halftone modulation process make GlossmarkTM images very difficult to detect by a scanner and even more challenging to reproduce through scanning and printing. The GlossmarkTM technology is ideally suitable for document authentication and graphics enhancement. Its digital implementation provides a capability to embed variable data as digital watermarks into individual prints quickly and economically.

  18. Digital Technology and Mental Health Interventions: Opportunities and Challenges

    OpenAIRE

    Aguilera, Adrian

    2015-01-01

    The growth of the Internet, mobile phones, social media and other digital technologies has changed our world in many ways. It has provided individuals with information that was previously only available to a select few. An example of the reach of technology is data that as of October 2012, there are over 6 billion phones worldwide (BBC, 2012). The availability of data in real time has presented hopes of intervening more efficiently and managing health problems by leveraging limited human reso...

  19. Plasma technology and its use in flat panel digital radiography.

    Science.gov (United States)

    Zur, Albert

    2010-01-01

    Plasma DR technology is used to produce a cost effective flat panel x-ray detector that acquires digital x-ray images with excellent diagnostic quality. The detector is radiation hard and permanently zero defect, with a full virtual pixel matrix that has no dead lines, pixels, or dead pixel clusters. The technology also allows the full potential of large area amorphous Selenium imaging to finally be realized (see Figure 4).

  20. Tim Berners-Lee receives the Millennium Technology Prize

    CERN Multimedia

    2004-01-01

    On 15 April, for his invention of the Web, Tim Berners-Lee was awarded the first ever Millennium Technology Prize by the Finnish Technology Award Foundation, which recognises technological innovations of lasting benefit to society. "Tim Berners-Lee's invention perfectly encapsulates the spirit of the Prize. The Web is encouraging new types of social networks, contributing to transparency and democracy, and opening up new avenues for information management and business development," underlined Pekka Tarjanne, chairman of the jury and former Secretary-General of the International Telecommunication Union (ITU). Tim Berners-Lee is congratulated by Jukka Valtasaari, Finland's Ambassador to the United States. Tim Berners-Lee created the first server, browser and editor, the HTML code, the URL address and the HTTP transmission protocol at CERN in 1990. CERN released the Web into the public domain in 1993. Tim Berners-Lee is currently head of the World Wide Web Consortium, managed by ERCIM (Europe...

  1. Technology and Music Education in a Digitized, Disembodied, Posthuman World

    Science.gov (United States)

    Thwaites, Trevor

    2014-01-01

    Digital forms of sound manipulation are eroding traditional methods of sound development and transmission, causing a disjuncture in the ontology of music. Sound, the ambient phenomenon, is becoming disrupted and decentred by the struggles between long established controls, beliefs and desires as well as controls from within technologized contexts.…

  2. Screen Capture Technology: A Digital Window into Students' Writing Processes

    Science.gov (United States)

    Seror, Jeremie

    2013-01-01

    Technological innovations and the prevalence of the computer as a means of producing and engaging with texts have dramatically transformed how literacy is defined and developed in modern society. This rise in digital writing practices has led to a growing number of tools and methods that can be used to explore second language (L2) writing…

  3. Pre-Service Teacher Self-Efficacy in Digital Technology

    Science.gov (United States)

    Lemon, Narelle; Garvis, Susanne

    2016-01-01

    Self-efficacy is an important motivational construct for primary school teachers (teachers of children aged 5-12 years) within Australia. Teacher self-efficacy beliefs will determine the level of teacher confidence and competence to engage with a task. In this study, we explore engagement with digital technology and the associated learning and…

  4. Animation, embodiment, and digital media human experience of technological liveliness

    CERN Document Server

    Chow, K

    2013-01-01

    Animation, Embodiment and Digital Media articulates the human experience of technology-mediated animated phenomena in terms of sensory perception, bodily action and imaginative interpretation, suggesting a new theoretical framework with analyses of exemplary user interfaces, video games and interactive artworks.

  5. "Digital Natives": An Asian Perspective for Using Learning Technologies

    Science.gov (United States)

    Kennedy, David M.; Fox, Bob

    2013-01-01

    Students entering universities in the 21st century have been described variously as digital natives, the millennial generation or the net generation. Considerable study has occurred around the world to determine the knowledge, skills, understanding and the purposes to which this group of individuals makes technology work for them. A number of…

  6. Composing with New Technology: Teacher Reflections on Learning Digital Video

    Science.gov (United States)

    Bruce, David L.; Chiu, Ming Ming

    2015-01-01

    This study explores teachers' reflections on their learning to compose with new technologies in the context of teacher education and/or teacher professional development. English language arts (ELA) teachers (n = 240) in 15 courses learned to use digital video (DV), completed at least one DV group project, and responded to open-ended survey…

  7. Digital radiographic technology; non-destructive testing of tubine blades

    NARCIS (Netherlands)

    Penumadu, P.S.

    2014-01-01

    Inspection of turbine blades has always been a big challenge. Any irregularities in the blade have a huge impact on the gas turbine, so these blades have to be manufactured and inspected in the most sophisticated way possible. The evolution of digital radiographic technology took a leap forward to

  8. Digital radiographic technology; non-destructive testing of tubine blades

    NARCIS (Netherlands)

    Penumadu, P.S.

    2014-01-01

    Inspection of turbine blades has always been a big challenge. Any irregularities in the blade have a huge impact on the gas turbine, so these blades have to be manufactured and inspected in the most sophisticated way possible. The evolution of digital radiographic technology took a leap forward to s

  9. Educational Digital Technologies in Developing Countries Challenge Third Party Providers

    Science.gov (United States)

    Passey, Don; Laferrière, Thérèse; Ahmad, Manal Yazbak-Abu; Bhowmik, Miron; Gross, Diana; Price, Janet; Resta, Paul; Shonfeld, Miri

    2016-01-01

    In this conceptual paper, we consider issues and challenges of third party and governmental organisations in planning and implementing access to and uses of digital technologies for learning and teaching in developing countries. We consider failures and weaknesses in the planning and implementation processes highlighted by research in developed…

  10. Supporting Teachers Developing Mathematical Tasks with Digital Technology

    Science.gov (United States)

    Ratnayake, Iresha; Oates, Greg; Thomas, Mike

    2016-01-01

    A crucial step towards improving the conceptual use of digital technology (DT) in the mathematics classroom is to increase teacher involvement in the development of tasks. Hence, this research considers some teacher factors that might influence DT algebra task development and implementation in secondary schools. We observed and assisted one group…

  11. Analytical estimation of laser phase noise induced BER floor in coherent receiver with digital signal processing.

    Science.gov (United States)

    Vanin, Evgeny; Jacobsen, Gunnar

    2010-03-01

    The Bit-Error-Ratio (BER) floor caused by the laser phase noise in the optical fiber communication system with differential quadrature phase shift keying (DQPSK) and coherent detection followed by digital signal processing (DSP) is analytically evaluated. An in-phase and quadrature (I&Q) receiver with a carrier phase recovery using DSP is considered. The carrier phase recovery is based on a phase estimation of a finite sum (block) of the signal samples raised to the power of four and the phase unwrapping at transitions between blocks. It is demonstrated that errors generated at block transitions cause the dominating contribution to the system BER floor when the impact of the additive noise is negligibly small in comparison with the effect of the laser phase noise. Even the BER floor in the case when the phase unwrapping is omitted is analytically derived and applied to emphasize the crucial importance of this signal processing operation. The analytical results are verified by full Monte Carlo simulations. The BER for another type of DQPSK receiver operation, which is based on differential phase detection, is also obtained in the analytical form using the principle of conditional probability. The principle of conditional probability is justified in the case of differential phase detection due to statistical independency of the laser phase noise induced signal phase error and the additive noise contributions. Based on the achieved analytical results the laser linewidth tolerance is calculated for different system cases.

  12. Digital Technologies and a Changing Profession

    DEFF Research Database (Denmark)

    Plesner, Ursula; Raviola, Elena

    2016-01-01

    Purpose: The purpose of this article is to investigate what role particular new management devices play in the development of the news profession in an organizational setting shifting to new technologies. Design/methodology/approach: This is studied through of observations of work practices...... in the newsroom and through documentary research and qualitative interviews with managers, editors, and other professionals. Findings: It is shown that management devices such as the news table and the news concept are central to the reorganization of news work, as they realize managers’ strategies, just like...... they produce new practices and power relationships. It is shown that the devices produce increased collaboration among journalists and interaction between managers and output journalists, that mundane work and power is delegated to technological devices and that news products are increasingly standardized...

  13. Digital technologies to generate health awareness

    OpenAIRE

    Herman Adriaan van Wietmarschen

    2015-01-01

    Background: It is well known that most chronic diseases are the result of an unhealthy life-style. Nevertheless, it appears to be very difficult to motivate people to adopt more healthy habits. Even after receiving a diagnosis of a chronic disease, these habits seem to be too strong to overcome by most people. This mechanism of strong, stable patterns of behavior can be very well described and explored by using complexity science. This field has come up with concepts and tools to study the dy...

  14. Mistaking Computers for Technology: Technology Literacy and the Digital Divide

    Science.gov (United States)

    Amiel, Tel

    2006-01-01

    No other information and communication technology has swept the globe with greater speed than the Internet, having the potential to promote vast social, economic, and political transformations. As new technologies become available the pattern of adoption and diffusion creates disparities in access and ownership. At the most basic this gap is…

  15. Digital Technologies and performative pedagogies: Repositioning the visual

    Directory of Open Access Journals (Sweden)

    Kathryn Grushka

    2010-05-01

    Full Text Available Images are becoming a primary means of information presentation in the digitized global media and digital technologies have emancipated and democratized the image. This allows for the reproduction and manipulation of images on a scale never seen before and opens new possibilities for teachers schooled in critical visuality. This paper reports on an innovative pre-service teacher training course in which a cross-curricula cohort of secondary teachers employed visual performative competencies to produce a series of learning objects on a digital platform. The resulting intertextual narratives demonstrate that the manipulation of image and text offered by digital technologies create a powerful vehicle for investigating knowledge and understandings, evolving new meaning and awakening latent creativity in the use of images for meaning making. This research informs the New Literacies and multimodal fields of enquiry and argues that visuality is integral to any pedagogy that purports to be relevant to the contemporary learner. It argues that the visual has been significantly under-valued as a conduit for knowledge acquisition and meaning making in the digital environment and supports the claim that critical literacy, interactivity, experimentation and production are vital to attaining the tenets of transformative education (Buckingham, 2007; Walsh, 2007; Cope & Kalantzis, 2008.

  16. Re-configurable digital receiver for optically envelope detected half cycle BPSK and MSK radio-on-fiber signals

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Prince, Kamau; Zibar, Darko

    2011-01-01

    novel digital receiver consists of a digital signal processing unit integrating functions such as filtering, peak-powers detection, symbol synchronization and signal demodulation for optically envelope detected half-cycle binary phase-shift-keying and minimum-shift-keying signals. Furthermore, radio......We present the first known integration of a digital receiver into optically envelope detection radio-on-fiber systems. We also present a re-configurable scheme for two different types of optically envelope detected wireless signals while keeping the complexity of used optical components low. Our......-frequency signal down-conversion is not required in our proposed approach; simplifying evens more the optical receiver front-end. We experimentally demonstrate error-free optical transmission (bit-error rate corresponding to 10−3 related to FEC-compatible levels) for both 416.6 Mbit/s half-cycle binary phase...

  17. Digital Health Technologies to Promote Lifestyle Change and Adherence.

    Science.gov (United States)

    Khan, Numan; Marvel, Francoise A; Wang, Jane; Martin, Seth S

    2017-08-01

    Cardiovascular disease is the leading cause of morbidity and mortality worldwide with an estimated 17.5 million deaths annually, or 31% of all global deaths, according to the World Health Organization. The majority of these deaths are preventable by addressing lifestyle modification (i.e., smoking cessation, diet, obesity, and physical inactivity) and promoting medication adherence. At present, initiatives to develop cost-effective modalities to support self-management, lifestyle modification, and medication adherence are a leading priority. Digital health has rapidly emerged as technology with the potential to address this gap in cardiovascular disease self-management and transform the way healthcare has been traditionally delivered. However, limited evidence exists about the type of technologies available and how they differ in functionality, effectiveness, and application. We aimed to review the most important and relevant recent studies addressing health technologies to promote lifestyle change and medication adherence including text messaging, applications ("apps"), and wearable devices. The current literature indicates that digital health technologies will likely play a prominent role in future cardiovascular disease management, risk reduction, and delivery of care in both resource-rich and resource-limited settings. However, there is limited large-scale evidence to support adoption of existing interventions. Further clinical research and healthcare policy change are needed to move the promise of new digital health technologies towards reality.

  18. Development of receiving-detecting circuit for digital radiographic systems with improved spatial resolution

    Science.gov (United States)

    Ryzhikov, Volodymir D.; Opolonin, Oleksandr D.; Galkin, Serhiy M.; Voronkin, Yevheniy F.; Lysetska, Olena K.; Kostyukevych, Serhiy A.

    2009-08-01

    Detection of X-ray radiation by digital radiographic systems (DRS) is realized using multi-element detector arrays of scintillator-photodiode (S-PD) type. Accounting for our experience in development of X-ray introscopy systems, possibilities can be found for improvement of DRS detection efficiency. Namely, a more efficient use of the dynamic range of the analog-to-digit converter by means of instrumental compensation of scatter of detector characteristics and smaller apertures of individual detection channels. However, smaller apertures lead to lower levels of useful signals, and a problem emerges of signal interference over neighboring channels, which is related to optical separation of the scintillation elements. Also, more compact arrangement of electronic components of preamplifiers is achieved. The latter problem is solved by using multi-channel (from 32 to 1024 channels) photoreceiving devices (PRD). PRD has a set of photosensitive elements formed on one crystal, as well as shift registers ensuring preliminary amplification of signals and series connection to one outlet. The work envisages creation of receiving-detecting circuit (RDC) with improved spatial resolution (ISR) with the aim of producing advanced DRS with improved characteristics: density resolution better than 0.9%, and detecting ability allowing detection of θ 0.5 mm steel wire behind 6 mm steel. The work will result in the development of RDC with ISR (800-200 microns). In combination with various ionizing radiation sources and scanning mechanisms this will allow creation of DRS for many tasks of non-destructive testing (NDT) and technical diagnostics (TD), in particular, for check-up of pipelines, objects of oil and gas industries, etc. This work was supported by the Ministry of Education and Science of Ukraine, the U.S. Civilian Research and Development Foundation (CRDF), and by the NATO Science for Peace and Security Program (Project SfP-982823).

  19. Research status and application prospects of digital technology in orthopaedics.

    Science.gov (United States)

    Chen, Yan-xi; Zhang, Kun; Hao, Yi-ni; Hu, Yong-cheng

    2012-08-01

    In the last 10 years, basic and clinical research in orthopaedics has developed rapidly. Understanding of orthopaedic disorders involves not only routine diagnosis, but also the pursuit of highly efficient and accurate three-dimensional imaging of the intra- and extra-medullary distribution, form and structure of orthopaedic disorders, thus allowing scientific evaluation of the indications for surgery, drawing up of the best surgical plan, minimization of operative trauma and the earliest possible restoration of limb function. Meanwhile, the most important type of basic research, which was previously biomechanical research, has gradually become computational biomechanics based on in vitro cadaver experiments. This review aims to summarize the research status and application prospects of digital technology in orthopaedics, including virtual reality technology, reverse engineering and rapid prototyping techniques, computational biomechanics, computer navigation technology and management of digitization of medical records. © 2012 Tianjin Hospital and Wiley Publishing Asia Pty Ltd.

  20. All-Digital ADC Design in 65 nm CMOS Technology

    OpenAIRE

    Pathapati, Srinivasa Rao

    2014-01-01

    The design of analog and complex mixed-signal circuits in a deep submicron CMOS process technology is a big challenge. This makes it desirable to shift data converter design towards the digital domain. The advantage of using a fully digital ADC design rather than a traditional analog ADC design is that the circuit is defined by an HDL description and automatically synthesized by tools. It offers low power consumption, low silicon area and a fully optimized gate-level circuit that reduces the ...

  1. Digital signature technology for health care applications.

    Science.gov (United States)

    Wang, H A; Wang, Y Z; Wang, S

    2001-03-01

    The personal computer and the Internet have provided many useful services to both health care professionals and the general public. However, security remains a key factor that could limit their further growth potential. We reviewed and assessed the potential use of the cryptographic technique to resolve security issues. We also analyzed services available in the current market environment and determined their viability in supporting health care applications. While the cryptographic application has a great potential in protecting security of health care information transmitted over the Internet, a nationwide security infrastructure is needed to support deployment of the technology. Although desirable, it could be cost prohibitive to build a national system to be dedicated for the health care purpose. A hybrid approach that involves the government's development of a dedicated security infrastructure for health care providers and the use of commercial off-the-shelf products and services by the general public offers the most cost-effective and viable approach.

  2. Bits of Homeland: Generational and Gender Transformations of Moroccan-Dutch Youth using digital technologies

    NARCIS (Netherlands)

    Leurs, K.H.A.; Ponzanesi, S.

    2013-01-01

    Generational and gendered specificities of digital technology use within migrant families remain understudied and undertheorized (Green & Kabir, 2012). Digital technologies are used among descendants of migrants to sustain and update networks while simultaneously they allow the younger generation to

  3. Digital image processing for the earth resources technology satellite data.

    Science.gov (United States)

    Will, P. M.; Bakis, R.; Wesley, M. A.

    1972-01-01

    This paper discusses the problems of digital processing of the large volumes of multispectral image data that are expected to be received from the ERTS program. Correction of geometric and radiometric distortions are discussed and a byte oriented implementation is proposed. CPU timing estimates are given for a System/360 Model 67, and show that a processing throughput of 1000 image sets per week is feasible.

  4. Reducing the Digital Divide among Children Who Received Desktop or Hybrid Computers for the Home

    Science.gov (United States)

    Zilka, Gila Cohen

    2016-01-01

    Researchers and policy makers have been exploring ways to reduce the digital divide. Parameters commonly used to examine the digital divide worldwide, as well as in this study, are: (a) the digital divide in the accessibility and mobility of the ICT infrastructure and of the content infrastructure (e.g., sites used in school); and (b) the digital…

  5. Digital technologies to generate health awareness

    Directory of Open Access Journals (Sweden)

    Herman Adriaan van Wietmarschen

    2015-10-01

    A third use case for improving health awareness is the launch of a HealthCafé. The aim is to inspire people to measure their own health and measure the effects of interventions on their health, using all sorts of do-it-your-self technologies. The current version of the HealthCafé offers first of all a physical location where people can interact. It also offers devices such as activity trackers, glucose and cholesterol measurement devices, questionnaires, and a personal internet portal to store and analyse the data. The goal is to empower people and give people more control over their own health. Conclusions: Complexity science offers new opportunities to create health awareness. We have shown how a systems dynamics software tool can be used in group model building sessions to generate a shared understanding of a health problem among stakeholders. The resulted in a successful integrative overweight treatment program at a rehabilitation centre in the Netherlands. The HealthCafé was launched as a living lab which can be used by people to explore their own health and conduct studies on themselves. These activities are aiming for a transition in health care towards more awareness as the personal level, empowerment and thereby increasing the chances for successful life-style changes towards more health and happiness.

  6. [Evaluation of bone mineral density using digital image processing in children receiving anticonvulsants].

    Science.gov (United States)

    Suzuki, Keiko; Ueda, Satoru; Umezu, Ryouji; Matsuoka, Hisafumi; Sugihara, Shigetaka

    2007-09-01

    Bone mineral density (BMD) increases rapidly in a biphasic manner in childhood. During and after adolescence, BMD correlates more closely with bone age than chronological age. Digital image processing (DIP) allows the rapid assessment of BMD and bone age on one X-ray film. Herein, using DIP methods, the effects of various anticonvulsants on chronological and bone age were evaluated in 98 epilepsy patients (age range, 3-15 years) with no intellectual or motor disorders or diseases affecting bone metabolism. All patients were taking one or a combination of the following anticonvulsants: valproate sodium (VPA); carbamazepine (CBZ); and phenobarbital (PB). Bone maturation scores for radius-ulnar-short bones (RUS) were calculated using Tanner-Whitehouse 2 methods. Bone age was determined based on standard Japanese bone-maturation scores. In each patient, Z-scores for chronological and bone ages were calculated by subtracting standard BMD for gender and age from each BMD, then dividing the result by the standard deviation. The Z-score for each drug in relation to the administration period was analyzed using the Mann-Whitney test. For chronological age, significant differences in BMD were observed regarding the administration periods in children taking multiple drugs, but not in children on VPA, CBZ, or PB monotherapy. For bone age, no significant differences in BMD were observed regarding the administration periods for all drugs. Children taking multiple drugs showed a significant negative correlation between administration period and Z-scores for BMD calculated based on chronological age (Spearman rank correlation: - 0.457, p = 0.008), but not bone age. Among children receiving long-term VPA administration, bone age was delayed approximately 1 year, and bone maturation may have been delayed. No delay in bone age was noted among children receiving long-term administration of multiple drugs, suggesting that these anticonvulsants do not influence bone maturity. These

  7. Solar augmentation for process heat with central receiver technology

    Science.gov (United States)

    Kotzé, Johannes P.; du Toit, Philip; Bode, Sebastian J.; Larmuth, James N.; Landman, Willem A.; Gauché, Paul

    2016-05-01

    Coal fired boilers are currently one of the most widespread ways to deliver process heat to industry. John Thompson Boilers (JTB) offer industrial steam supply solutions for industry and utility scale applications in Southern Africa. Transport cost add significant cost to the coal price in locations far from the coal fields in Mpumalanga, Gauteng and Limpopo. The Helio100 project developed a low cost, self-learning, wireless heliostat technology that requires no ground preparation. This is attractive as an augmentation alternative, as it can easily be installed on any open land that a client may have available. This paper explores the techno economic feasibility of solar augmentation for JTB coal fired steam boilers by comparing the fuel savings of a generic 2MW heliostat field at various locations throughout South Africa.

  8. Digital Microdroplet Ejection Technology-Based Heterogeneous Objects Prototyping

    Directory of Open Access Journals (Sweden)

    Na Li

    2016-01-01

    Full Text Available An integrate fabrication framework is presented to build heterogeneous objects (HEO using digital microdroplets injecting technology and rapid prototyping. The heterogeneous materials part design and manufacturing method in structure and material was used to change the traditional process. The net node method was used for digital modeling that can configure multimaterials in time. The relationship of material, color, and jetting nozzle was built. The main important contributions are to combine the structure, material, and visualization in one process and give the digital model for manufacture. From the given model, it is concluded that the method is effective for HEO. Using microdroplet rapid prototyping and the model given in the paper HEO could be gotten basically. The model could be used in 3D biomanufacturing.

  9. Digital technologies as truth-bearers in health care.

    Science.gov (United States)

    Bartlett, Ruth; Balmer, Andrew; Brannelly, Petula

    2017-01-01

    In this paper, we explore the idea of digital technologies as truth-bearers in health care and argue that devices like SenseCam, which facilitate reflection and memory recall, have a potentially vital role in healthcare situations when questions of veracity are at stake (e.g., when best interest decisions are being made). We discuss the role of digital technologies as truth-bearers in the context of nursing people with dementia, as this is one area of health care in which the topic of truth-telling has been hotly debated. People with dementia have been excluded from research studies and decisions that affect their lives because they are not regarded as truth-bearers-that is, as being capable of giving truthful accounts of their experiences. Also, considerable research has focused on the ethics of lying to and deceiving people with dementia. Given their increasing prominence in healthcare settings, there has been surprisingly little discussion of what role digital technologies might play in relation to these questions of truth and deception. Drawing on theories from science and technology studies (STS), we explore their possible future role in some of the truth-making processes of health care. In particular, we discuss the potential value of constraints on use of SenseCam to support the accounts of people with dementia as part of their care. © 2016 John Wiley & Sons Ltd.

  10. HIPSR: A Digital Signal Processor for the Parkes 21-cm Multibeam Receiver

    Science.gov (United States)

    Price, D. C.; Staveley-Smith, L.; Bailes, M.; Carretti, E.; Jameson, A.; Jones, M. E.; van Straten, W.; Schediwy, S. W.

    2016-11-01

    HIPSR (HI-Pulsar) is a digital signal processing system for the Parkes 21-cm Multibeam Receiver that provides larger instantaneous bandwidth, increased dynamic range, and more signal processing power than the previous systems in use at Parkes. The additional computational capacity enables finer spectral resolution in wideband HI observations and real-time detection of Fast Radio Bursts during pulsar surveys. HIPSR uses a heterogeneous architecture, consisting of FPGA-based signal processing boards connected via high-speed Ethernet to high performance compute nodes. Low-level signal processing is conducted on the FPGA-based boards, and more complex signal processing routines are conducted on the GPU-based compute nodes. The development of HIPSR was driven by two main science goals: to provide large bandwidth, high-resolution spectra suitable for 21-cm stacking and intensity mapping experiments; and to upgrade the Berkeley-Parkes-Swinburne Recorder (BPSR), the signal processing system used for the High Time Resolution Universe (HTRU) Survey and the Survey for Pulsars and Extragalactic Radio Bursts (SUPERB).

  11. Nyquist WDM superchannel using offset-16QAM and receiver-side digital spectral shaping.

    Science.gov (United States)

    Xiang, Meng; Fu, Songnian; Tang, Ming; Tang, Haoyuan; Shum, Perry; Liu, Deming

    2014-07-14

    The performance of Nyquist WDM superchannel using advanced modulation formats with coherent detection is degraded due to the existence of both inter-symbol interference (ISI) and inter-channel interference (ICI). Here, we propose and numerically investigate a Nyquist WDM superchannel using offset-16QAM and receiver-side digital spectral shaping (RS-DSS), achieving a spectral efficiency up to 7.44 bit/s/Hz with 7% hard-decision forward error correction (HD-FEC) overhead. Compared with Nyquist WDM superchannel using 16QAM and RS-DSS, the proposed system has 1.4 dB improvement of required OSNR at BER = 10(-3) in the case of back-to-back (B2B) transmission. Furthermore, the range of launched optical power allowed beyond HD-FEC threshold is drastically increased from -6 dBm to 1.2 dBm, after 960 km SSMF transmission with EDFA-only. In particular, no more than 1.8 dB required OSNR penalty at BER = 10(-3) is achieved for the proposed system even with the phase difference between channels varying from 0 to 360 degree.

  12. Review and Prospect of Cobalt-60 Digital Radiography Inspection Technology

    Directory of Open Access Journals (Sweden)

    AN Ji-gang

    2015-11-01

    Full Text Available This article is a review and prospect of the research, development and industrialization of Cobalt-60 digital radiography inspection technology based on the national requirements in the recent 20 years, which is leaded by Institute of Nuclear and New Energy Technology (INET of TsinghuaUniversity. The research purpose, innovative approach and main academic achievements of this technology were described systematically. The industrial equipment varieties, performance, running condition and application effect were introduced, and the outstanding advantages and prospects of the technology are summarized. In the paper, some understanding obstacles or mistakes encountered during the promotion and application were sorted out and explained too to help the improvement and development of the new relevant technology.

  13. IMPLEMENTATION OF A VERILOG-BASED DIGITAL RECEIVER FOR 2.4 GHz ZIGBEE APPLICATIONS ON FPGA

    Directory of Open Access Journals (Sweden)

    RAFIDAH AHMAD

    2014-02-01

    Full Text Available This paper presents the implementation of a digital receiver for 2.4 GHz Zigbee IEEE 802.15.4 applications on a Spartan3E XC3S500E field programmable gate array (FPGA. The proposed digital receiver comprises an offset quadrature phase shift keying (OQPSK demodulator, chip synchronization, and a de-spreading block. A new design method that uses Verilog hardware description language (HDL code through Xilinx ISE version 12 was developed to design these blocks. These blocks were integrated into one top module for optimization. Simulation and measurement were conducted to verify the functionality of the receiver. Implementation results show that the receiver design matched the theoretical expectation. The implementation configuration required up to 22% less slices, flip-flops (FFs, and look-up tables (LUTs than that in previous research. The clock frequencies used were as low as 250 kHz and 2 MHz.

  14. Using and choosing digital health technologies: a communications science perspective.

    Science.gov (United States)

    Ovretveit, John; Wu, Albert; Street, Richard; Thimbleby, Harold; Thilo, Friederike; Hannawa, Annegret

    2017-03-20

    Purpose The purpose of this paper is to explore a non-technical overview for leaders and researchers about how to use a communications perspective to better assess, design and use digital health technologies (DHTs) to improve healthcare performance and to encourage more research into implementation and use of these technologies. Design/methodology/approach Narrative overview, showing through examples the issues and benefits of introducing DHTs for healthcare performance and the insights that communications science brings to their design and use. Findings Communications research has revealed the many ways in which people communicate in non-verbal ways, and how this can be lost or degraded in digitally mediated forms. These losses are often not recognized, can increase risks to patients and reduce staff satisfaction. Yet digital technologies also contribute to improving healthcare performance and staff morale if skillfully designed and implemented. Research limitations/implications Researchers are provided with an introduction to the limitations of the research and to how communications science can contribute to a multidisciplinary research approach to evaluating and assisting the implementation of these technologies to improve healthcare performance. Practical implications Using this overview, managers are more able to ask questions about how the new DHTs will affect healthcare and take a stronger role in implementing these technologies to improve performance. Originality/value New insights into the use and understanding of DHTs from applying the new multidiscipline of communications science. A situated communications perspective helps to assess how a new technology can complement rather than degrade professional relationships and how safer implementation and use of these technologies can be devised.

  15. [Application of three-dimensional digital technology in the diagnosis and treatment planning in orthodontics].

    Science.gov (United States)

    Bai, Y X

    2016-06-01

    Three-dimensional(3D)digital technology has been widely used in the field of orthodontics in clinical examination, diagnosis, treatment and curative effect evaluation. 3D digital technology greatly improves the accuracy of diagnosis and treatment, and provides effective means for personalized orthodontic treatment. This review focuses on the application of 3D digital technology in the field of orthodontics.

  16. Disruptive Technology Enhanced Learning: The Use and Misuse of Digital Technologies in Higher Education

    Science.gov (United States)

    Flavin, Michael

    2017-01-01

    This book is about how technologies are used in practice to support learning and teaching in higher education. Despite digitization and e-learning becoming ever-increasingly popular in university teaching settings, this book convincingly argues instead in favour of simple and convenient technologies, thus disrupting traditional patterns of…

  17. The vulnerabilities of digital documents: Technological obsolescence and lack of policies and practices of digital preservation

    Directory of Open Access Journals (Sweden)

    Henrique Machado dos Santos

    2015-07-01

    Full Text Available Objective. This paper attempts to discuss the theoretical issues related to the technological obsolescence, implementation of organizational policies, preservation strategies and computerized systems. Method. It develops the literature previously published materials such as books, theses, websites and articles in scientific journals indexed in Google Scholar and CAPES Journal Portal. Data collection is based on qualitative analysis, and performs a literature review can provide state of the art on preserving and fragility of digital documents. Results. Among the results can be considered the technological obsolescence as consequence of the technology itself motivated by unbridled development. In this way, it has been reaching software, file formats, operating systems and professionals responsible for preservation, and thus a significant part of the memory of contemporary societies is at risk. Conclusions. It highlights the importance of institutional policies, digital preservation strategies and computerized systems. Through these is can plan, monitor and treat digital documents, minimizing the effects of technological obsolescence in order to preserve its content and its reliability.

  18. Digital Receiver-based Electronic Intelligence System Configuration for the Detection and Identification of Intrapulse Modulated Radar Signals

    Directory of Open Access Journals (Sweden)

    A. K. Singh

    2014-03-01

    Full Text Available An optimum electronic intelligence system configuration incorporating the state of the art technologies and achieving the highest parameter accuracies while processing the complex intrapulse modulated radar signals is presented in this paper. The system is based on the quad digital receiver, a state of the art single board solution for the detection and analysis of modern radar signals. The system consists of base line interferometry  configuration for high accuracy direction finding measurement with sector selection based on amplitude direction finding technique. Advanced signal processing algorithms with time frequency analysis are implemented in real time in field programmable gate array to extract all the basic as well as advanced parameters of frequency and phase modulations such as chirp, barker, and poly-phase (Frank, P1-P4 codes in addition to the pulse and continuous wave signals. The intercepted intrapulse modulated signal parameters have been extracted with very high accuracy and sensitivity.Defence Science Journal, 2014, 64(2, pp. 152-158. DOI: http://dx.doi.org/10.14429/dsj.64.5091

  19. What Does Yaghan Have to Do with Digital Technology?

    Directory of Open Access Journals (Sweden)

    Lenore A. Grenoble

    2002-01-01

    Full Text Available Digital media offers some powerful new ways to organize and transmit linguistic data. This editorial suggests that linguists need to be more aggressive in exploting the technology so that information about language is spread more rapidly and in a more efficient format. To make this point, the case of fieldwork on Yaghan is examined. Though early fieldwork was carried out on Yaghan very little about the language is known because of the way the data was collected and reported.

  20. Technology ecosystems and digital business ecosystems for business

    OpenAIRE

    Marjamaa-Mankinen, L. (Liisa)

    2016-01-01

    The purpose of this study was to find out the progress in the research of technology ecosystems and digital business ecosystems and to combine that information for business purposes by the utilization of information about business ecosystems. The need for this information emerged at the Department of Information Processing Science in the context of European Union research projects. The information gained is expected to assist to increase possibilities both for the research and for the persona...

  1. Linewidth tolerance of digital coherent receiver using Viterbi & Viterbi RF carrier recovery for radio-over-fibre links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Larsen, Knud J.

    2009-01-01

    for phase-modulated RoF optical links (2). The RF signal processing in (2) is performed using maximum likelihood RF carrier phase estimation (2). In this paper, we investigate the performance of the proposed digital coherent receiver in (2) using feedforward Viterbi & Viterbi RF carrier recovery algorithm...

  2. Reconfigurable Digital Coherent Receiver for Metro-Access Networks Supporting Mixed Modulation Formats and Bit-rates

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Guerrero Gonzalez, Neil; Arlunno, Valeria

    2013-01-01

    A single, reconfigurable, digital coherent receiver is proposed and experimentally demonstrated for converged wireless and optical fiber transport. The capacity of reconstructing the full transmitted optical field allows for the demodulation of mixed modulation formats and bit-rates. We performed...

  3. 76 FR 54496 - In the Matter of Certain Electronic Devices Having a Digital Television Receiver and Components...

    Science.gov (United States)

    2011-09-01

    ... Lincolnshire, Illinois. 76 FR. 32373-74. The complaint alleges violations of section 337 of the Tariff Act of... COMMISSION In the Matter of Certain Electronic Devices Having a Digital Television Receiver and Components..., and the sale within the United States after importation of certain electronic devices having a...

  4. Digital Technology in the protection of cultural heritage Bao Fan Temple mural digital mapping survey

    Science.gov (United States)

    Zheng, Y.

    2015-08-01

    Peng Xi county, Sichuan province, the Bao Fan temple mural digitization survey mapping project: we use three-dimensional laserscanning, multi-baseline definition digital photography, multi-spectral digital image acquisition and other technologies for digital survey mapping. The purpose of this project is to use modern mathematical reconnaissance mapping means to obtain accurate mural shape, color, quality and other data. Combined with field investigation and laboratory analysis results, and based on a comprehensive survey and study, a comprehensive analysis of the historical Bao Fan Temple mural artistic and scientific value was conducted. A study of the mural's many qualities (structural, material, technique, preservation environment, degradation, etc.) reveal all aspects of the information carried by the Bao Fan Temple mural. From multiple angles (archeology, architecture, surveying, conservation science and other disciplines) an assessment for the Bao Fan Temple mural provides basic data and recommendations for conservation of the mural. In order to achieve the conservation of cultural relics in the Bao Fan Temple mural digitization survey mapping process, we try to apply the advantages of three-dimensional laser scanning equipment. For wall murals this means obtaining three-dimensional scale data from the scan of the building and through the analysis of these data to help determine the overall condition of the settlement as well as the deformation of the wall structure. Survey analysis provides an effective set of conclusions and suggestions for appropriate mural conservation. But before data collection, analysis and research need to first to select the appropriate scanning equipment, set the appropriate scanning accuracy and layout position of stations necessary to determine the scope of required data. We use the fine features of the three-dimensional laser scanning measuring arm to scan the mural surface deformation degradation to reflect the actual state of

  5. Evaluation of urban underground space resources using digitalization technologies

    Directory of Open Access Journals (Sweden)

    Hehua Zhu

    2016-12-01

    Full Text Available Exploitation and utilization of urban underground space resources is gaining increasing attention in cities’ sustainable development. Due to the attributes of fragility and irreversibility, urban underground space resources can be extremely vulnerable to damage and it is often difficult in restoring their original state once damaged. Therefore, scientific and reasonable evaluation of urban underground space resources is of vital importance in urban planning and development. This paper first describes the content and methods for the evaluation of urban underground space resources, and introduces the digitalization technologies to handle the problems of strong subjectivity, low efficiency and rough precision encountered when using traditional evaluation tools. Then, the related concepts and main technologies for digitalization were demonstrated and an intelligent GIS-based engineering geology system was built. Based on the drilling information in Changzhou City, stratum standardization and 3D modeling of strata, underground structures and pipelines were conducted in the built intelligent system. Finally, with the help of spatial overlay analysis in the GIS-based platform and a combination of other digitalization technologies, the urban underground space resources of Changzhou City were evaluated. Maps of geological suitability were produced, which provide scientific guidance and reference for the exploitation and planning of urban underground space resources in Changzhou City. In addition, site selection for key projects was conducted based on the evaluation results using this platform.

  6. Inclusive Digital Technologies for People with Communication Disabilities

    DEFF Research Database (Denmark)

    Konnerup, Ulla

    2017-01-01

    inclusion and empowering people with communication difficulties are offered. However, more knowledge about how learners with special challenges benefit from ICT in their communication and learning and what kind of technology that qualify rehabilitation is needed. Based on research with people suffering from...... aphasia after a brain injury this chapter will demonstrate how digital technologies can support sufferer’s in acquiring some new ways to re-engage people in communicative relations and learning activities. Keywords: Communication disabilities, Inclusion, ICT, Identity-formation Learning, Empowerment...

  7. Semantic Technology to Exploit Digital Content Exposed as Linked Data

    CERN Document Server

    Albertoni, Riccardo

    2011-01-01

    The paper illustrates the research result of the application of semantic technology to ease the use and reuse of digital contents exposed as Linked Data on the web. It focuses on the specific issue of explorative research for the resource selection: a context dependent semantic similarity assessment is proposed in order to compare datasets annotated through terminologies exposed as Linked Data (e.g. habitats, species). Semantic similarity is shown as a building block technology to sift linked data resources. From semantic similarity application, we derived a set of recommendations underlying open issues in scaling the similarity assessment up to the Web of Data.

  8. Study on Modeling Technology in Digital Reactor System

    Institute of Scientific and Technical Information of China (English)

    刘晓平; 罗月童; 童莉莉

    2004-01-01

    Modeling is the kernel part of a digital reactor system. As an extensible platform for reactor conceptual design, it is very important to study modeling technology and develop some kind of tools to speed up preparation of all classical computing models. This paper introduces the background of the project and basic conception of digital reactor. MCAM is taken as an example for modeling and its related technologies used are given. It is an interface program for MCNP geometry model developed by FDS team (ASIPP & HUT), and designed to run on windows system. MCAM aims at utilizing CAD technology to facilitate creation of MCNP geometry model. There have been two ways for MCAM to utilize CAD technology:(1) Making use of user interface technology in aid of generation of MCNP geometry model;(2) Making use of existing 3D CAD model to accelerate creation of MCNP geometry model. This paper gives an overview of MCAM's major function. At last, several examples are given to demonstrate MCAM's various capabilities.

  9. Beyond Moore's Law: Harnessing spatial-digital disruptive technologies for Digital Earth

    Science.gov (United States)

    Foresman, Timothy W.

    2016-11-01

    Moore's law will reach its plateau by 2020. Big data, however, will continue to increase as the Internet of Things and social media converge into the new era of ‘huge data’. Disruptive technologies, including big data and cloud computing are forces impacting business and government communities. The truth of our collective future is suggested to align with the Digital Earth (DE) vision. Benefits of technological advances will be manifested from business performance improvements based on capitalizing the locational attributes of corporate and government assets - the foundation of big data. Better governance and better business represents a key foundation for sustainability and therefore should be explicit DE guiding principles.

  10. Digital coherent receiver for subcarrier multiplexed phase modulated radio-over-fibre signals

    DEFF Research Database (Denmark)

    Zibar, Darko; Larsen, Knud J.; Tafur Monroy, Idelfonso

    2009-01-01

    Digital coherent detection of multi-channel subcarrier multiplexed optically phase-modulated radio-over-fibre signals is experimentally demonstrated. Successful detection after transmission over a 40 km long fibre link of four or five 25 Mbaud BPSK/QPSK subcarrier channels in 5 GHz bandwidth...... is demonstrated using offline digital signal processing....

  11. A Survey of Complex Object Technologies for Digital Libraries

    Science.gov (United States)

    Nelson, Michael L.; Argue, Brad; Efron, Miles; Denn, Sheila; Pattuelli, Maria Cristina

    2001-01-01

    Many early web-based digital libraries (DLs) had implicit assumptions reflected in their architecture that the unit of focus in the DL (frequently "reports" or "e-prints") would only be manifested in a single, or at most a few, common file formats such as PDF or PostScript. DLs have now matured to the point where their contents are commonly no longer simple files. Complex objects in DLs have emerged from in response to various requirements, including: simple aggregation of formats and supporting files, bundling additional information to aid digital preservation, creating opaque digital objects for e-commerce applications, and the incorporation of dynamic services with the traditional data files. We examine a representative (but not necessarily exhaustive) number of current and recent historical web-based complex object technologies and projects that are applicable to DLs: Aurora, Buckets, ComMentor, Cryptolopes, Digibox, Document Management Alliance, FEDORA, Kahn-Wilensky Framework Digital Objects, Metadata Encoding & Transmission Standard, Multivalent Documents, Open eBooks, VERS Encapsulated Objects, and the Warwick Framework.

  12. A survey of passive technology for digital image forensics

    Institute of Scientific and Technical Information of China (English)

    LUO Weiqi; QU Zhenhua; PAN Feng; HUANG Jiwu

    2007-01-01

    Over the past years,digital images have been widely used in the Internet and other applications.Whilst image processing techniques are developing at a rapid speed,tampering with digital images without leaving any obvious traces becomes easier and easier.This may give rise to some problems such as image authentication.A new passive technology for image forensics has evolved quickly during the last few years.Unlike the signature-based or watermark-based methods,the new technology does not need any signature generated or watermark embedded in advance,it assumes that different imaging devices or processing would introduce different inherent patterns into the output images.These underlying patterns are consistent in the original untampered images and would be altered after some kind of manipulations.Thus,they can be used as evidence for image source identification and alteration detection.In this paper,we will discuss this new forensics technology and give an overview of the prior literatures.Some concluding remarks are made about the state of the art and the challenges in this novel technology.

  13. Film piracy in the era of digital technology

    Directory of Open Access Journals (Sweden)

    Petrović Vukašin

    2015-01-01

    Full Text Available Reproduction of films in the era of analog technology has been connected with a number of difficulties, involving, inter alia, technically complex process of reproduction, as well as high cash expenditures. In that sense, the very analog technology presented a barrier to reproduction of films by unauthorized persons. By switching to digital technology, the reproduction of mentioned copyright works became much easier, in terms of enabling individuals to, with easily available and relatively cheap technical means, in a fast and high quality way, make a large number of film copies. Since the digital era reflects progress of technology in the field of reproduction and distribution of films, as well as copyright works in general, the introduction of new exclusive rights in copyright law is very significant, as well as narrowing the existing limitations of copyright law rights and extension of duration of the protection. Effective enforcement of copyright protection in the new conditions opened a range of numerous issues, out of which the question of piracy in the field of film production is one of the most important, which presented the motivation for the author to cover this issue.

  14. Improved Construction of Auricular Prosthesis by Digital Technologies.

    Science.gov (United States)

    Nuseir, Amjad; Hatamleh, Muhanad; Watson, Jason; Al-Wahadni, Ahed M; Alzoubi, Firas; Murad, Mohammed

    2015-09-01

    Implant-retained auricular prostheses are a successful prosthetic treatment option for patients who are missing their ear(s) due to trauma, oncology, or birth defects. The prosthetic ear is aesthetically pleasing, composed of natural looking anatomical contours, shape, and texture along with good color that blends with surrounding existing skin. These outcomes can be optimized by the integration of digital technologies in the construction process. This report describes a sequential process of reconstructing a missing left ear by digital technologies. Two implants were planned for placement in the left mastoid region utilizing specialist biomedical software (Materialise, Belgium). The implant positions were determined underneath the thickest portion (of anti-helix area) left ear that is virtually simulated by means of mirror imaging of the right ear. A surgical stent recording the implant positions was constructed and used in implant fixtures placement. Implants were left for eight weeks, after which they were loaded with abutments and an irreversible silicone impression was taken to record their positions. The right existing ear was virtually segmented using the patient CT scan and then mirror imaged to produce a left ear, which was then printed using 3D printer (Z Corp, USA). The left ear was then duplicated in wax which was fitted over the defect side. Then, it was conventionally flasked. Skin color was digitalized using spectromatch skin color system (London, UK). The resultant silicone color was mixed as prescribed and then packed into the mold. The silicone was cured conventionally. Ear was trimmed and fitted and there was no need for any extrinsic coloring. The prosthetic ear was an exact match to the existing right ear in shape, skin color, and orientation due to the great advantages of technologies employed. Additionally, these technologies saved time and provided a base for reproducible results regardless of operator.

  15. Digitized Educational Technology: A Learning Tool Using Remotely Sensed Data

    Science.gov (United States)

    Love, Gloria Carter

    1999-01-01

    Digitized Educational software for different levels of instruction were developed and placed on the web (geocities). Students attending the Pre-Engineering Summer 1998 Camp at Dillard University explored the use of the software which included presentations, applications, and special exercises. Student comments were received and considered for adjustments. The second outreach program included students from Colton Junior High School and Natural Science Majors at Dillard University. The Natural Majors completed a second survey concerning reasons why students selected majors in the Sciences and Mathematics. Two student research assistants (DU) and faculty members/parents of Colton Junior High assisted.

  16. A reconfigurable OTA-C baseband filter with wide digital tuning for GNSS receivers

    Energy Technology Data Exchange (ETDEWEB)

    Pan Wenguang; Gan Yebing [Institute of Microelectronics, Chinese Academy of Sciences, Beijing 100029 (China); Ma Chengyan; Ye Tianchun, E-mail: panwenguang@casic.ac.c [Hangzhou Zhongke Microelectronics Co. Ltd, Hangzhou 310053 (China)

    2010-09-15

    The design of a digitally-tunable sixth-order reconfigurable OTA-C filter in a 0.18-{mu}m RFCMOS process is proposed. The filter can be configured as a complex band pass filter or two real low pass filters. An improved digital automatic frequency tuning scheme based on the voltage controlled oscillator technique is adopted to compensate for process variations. An extended tuning range (above 8:1) is obtained by using widely continuously tunable transconductors based on digital techniques. In the complex band pass mode, the bandwidth can be tuned from 3 to 24 MHz and the center frequency from 3 to 16 MHz. (semiconductor integrated circuits)

  17. Digital Technology Use by the Students and English Teachers and Self-Directed Language Learning

    Science.gov (United States)

    Sert, Nehir; Boynuegri, Ebru

    2017-01-01

    The digital era is a new challenge for teachers. While children get acquainted with the digital technology before the age of six, teachers, who have encountered with the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use technology particularly…

  18. Hybrid Placemaking in the Library: Designing Digital Technology to Enhance Users' On-Site Experience

    Science.gov (United States)

    Bilandzic, Mark; Johnson, Daniel

    2013-01-01

    This paper presents research findings and design strategies that illustrate how digital technology can be applied as a tool for "hybrid" placemaking in ways that would not be possible in purely digital or physical spaces. Digital technology has revolutionised the way people learn and gather new information. This trend has challenged the…

  19. Experimental Adaptive Digital Performance Monitoring for Optical DP-QPSK Coherent Receiver

    DEFF Research Database (Denmark)

    Borkowski, Robert; Zhang, Xu; Zibar, Darko;

    2011-01-01

    We report on a successful experimental demonstration of a digital optical performance monitoring (OPM) yielding satisfactory estimation accuracy along with adaptive impairment equalization. No observable penalty is measured when equalizer is driven by monitoring module....

  20. HD Photo: a new image coding technology for digital photography

    Science.gov (United States)

    Srinivasan, Sridhar; Tu, Chengjie; Regunathan, Shankar L.; Sullivan, Gary J.

    2007-09-01

    This paper introduces the HD Photo coding technology developed by Microsoft Corporation. The storage format for this technology is now under consideration in the ITU-T/ISO/IEC JPEG committee as a candidate for standardization under the name JPEG XR. The technology was developed to address end-to-end digital imaging application requirements, particularly including the needs of digital photography. HD Photo includes features such as good compression capability, high dynamic range support, high image quality capability, lossless coding support, full-format 4:4:4 color sampling, simple thumbnail extraction, embedded bitstream scalability of resolution and fidelity, and degradation-free compressed domain support of key manipulations such as cropping, flipping and rotation. HD Photo has been designed to optimize image quality and compression efficiency while also enabling low-complexity encoding and decoding implementations. To ensure low complexity for implementations, the design features have been incorporated in a way that not only minimizes the computational requirements of the individual components (including consideration of such aspects as memory footprint, cache effects, and parallelization opportunities) but results in a self-consistent design that maximizes the commonality of functional processing components.

  1. DIAGNOcam--a Near Infrared Digital Imaging Transillumination (NIDIT) technology.

    Science.gov (United States)

    Abdelaziz, Marwa; Krejci, Ivo

    2015-01-01

    In developed countries, clinical manifestation of carious lesions is changing: instead of dentists being confronted with wide-open cavities, more and more hidden caries are seen. For a long time, the focus of the research community was on finding a method for the detection of carious lesions without the need for radiographs. The research on Digital Imaging Fiber-Optic Transillumination (DIFOTI) has been an active domain. The scope of the present article is to describe a novel technology for caries diagnostics based on Near Infrared Digital Imaging Transillumination (NIDIT), and to give first examples of its clinical indications. In addition, the coupling of NIDIT with a head-mounted retinal image display (RID) to improve clinical workflow is presented. The novel NIDIT technology was shown to be useful as a diagnostic tool in several indications, including mainly the detection of proximal caries and, less importantly, for occlusal caries, fissures, and secondary decay around amalgam and composite restorations. The coupling of this technology with a head-mounted retinal image system allows for its very efficient implementation into daily practice.

  2. Digital image processing using parallel computing based on CUDA technology

    Science.gov (United States)

    Skirnevskiy, I. P.; Pustovit, A. V.; Abdrashitova, M. O.

    2017-01-01

    This article describes expediency of using a graphics processing unit (GPU) in big data processing in the context of digital images processing. It provides a short description of a parallel computing technology and its usage in different areas, definition of the image noise and a brief overview of some noise removal algorithms. It also describes some basic requirements that should be met by certain noise removal algorithm in the projection to computer tomography. It provides comparison of the performance with and without using GPU as well as with different percentage of using CPU and GPU.

  3. Review of Wideband Digital Channelized Receivers%宽带数字信道化接收机综述

    Institute of Scientific and Technical Information of China (English)

    龚仕仙; 魏玺章; 黎湘

    2013-01-01

    宽带数字信道化接收机以其高性能在电子战和无线电通信中有着重要的运用.本文基于复杂电磁环境下电子战的运用需求,分析了信道化接收机系统的发展现状和趋势;研究了目前的数字信道化接收机技术的主要系统结构及其发展趋势;重点分析了信道化接收机技术的发展历程和发展趋势.根据目前的信道化接收机系统和数字信道化接收机技术的现状可以看出,数字信道化接收机发展的一个趋势是:宽带数字化(大量子信道)和非均匀信道化接收机及动态信道化接收机.%Wideband digital channelized receivers have an important application in Electronic Warfare(EW)and wireless communication,especially in Electronic Intelligence systems(ELINT) and Radar Warning Receiver(RWR) systems.This paper introduces the channelized receiver systems and the structures of the channelized technique.And base on the analysis of the development history of the channelized Receivers,we can see that the channelized Receivers system trend towards wideband digital and the digital channelized technique trend towards nouniform channelized to make channelized Receivers more suitable to the modem EW.

  4. Frequency diversity wideband digital receiver and signal processor for solid-state dual-polarimetric weather radars

    Science.gov (United States)

    Mishra, Kumar Vijay

    The recent spate in the use of solid-state transmitters for weather radar systems has unexceptionably revolutionized the research in meteorology. The solid-state transmitters allow transmission of low peak powers without losing the radar range resolution by allowing the use of pulse compression waveforms. In this research, a novel frequency-diversity wideband waveform is proposed and realized to extenuate the low sensitivity of solid-state radars and mitigate the blind range problem tied with the longer pulse compression waveforms. The latest developments in the computing landscape have permitted the design of wideband digital receivers which can process this novel waveform on Field Programmable Gate Array (FPGA) chips. In terms of signal processing, wideband systems are generally characterized by the fact that the bandwidth of the signal of interest is comparable to the sampled bandwidth; that is, a band of frequencies must be selected and filtered out from a comparable spectral window in which the signal might occur. The development of such a wideband digital receiver opens a window for exciting research opportunities for improved estimation of precipitation measurements for higher frequency systems such as X, Ku and Ka bands, satellite-borne radars and other solid-state ground-based radars. This research describes various unique challenges associated with the design of a multi-channel wideband receiver. The receiver consists of twelve channels which simultaneously downconvert and filter the digitized intermediate-frequency (IF) signal for radar data processing. The product processing for the multi-channel digital receiver mandates a software and network architecture which provides for generating and archiving a single meteorological product profile culled from multi-pulse profiles at an increased data date. The multi-channel digital receiver also continuously samples the transmit pulse for calibration of radar receiver gain and transmit power. The multi

  5. Digital modeling technology for full dental crown tooth preparation.

    Science.gov (United States)

    Dai, Ning; Zhong, Yicheng; Liu, Hao; Yuan, Fusong; Sun, Yuchun

    2016-04-01

    A dental defect is one of the most common oral diseases, and it often requires a full crown restoration. In this clinical operation, the dentist must manually prepare the affected tooth for the full crown so that it has a convergence angle between 4° and 10°, no undercuts, and uniform and even shoulder widths and depths using a high speed diamond bur in the patient׳s mouth within one hour, which is a difficult task that requires visual-manual operation. The quality of the tooth preparation has an important effect on the success rate of the subsequent prosthodontic treatment. This study involved research into digital modeling technology for full dental crown tooth preparation. First, the margin line of the tooth preparation was designed using a semi-automatic interactive process. Second, the inserting direction was automatically computed. Then, the characteristic parameters and the constraints on the tooth preparation were defined for the model. Next, the shoulder and axial surface of the tooth preparation were formed using parametric modeling. Finally, the implicit surface of a radial basis function was used to construct the tooth preparation׳s occlusal surface. The experimental results verified that the method of digital modeling for full crown preparation proposed in this study can quickly and accurately implement personalized designs of various parameters, such as the shoulder width and the convergence angle; it provides a digital design tool for full crown preparation.

  6. Technology evaluation center assessment synopsis: full-field digital mammography.

    Science.gov (United States)

    Rothenberg, Barbara M; Ziegler, Kathleen M; Aronson, Naomi

    2006-08-01

    Full-field digital mammography (FFDM) is proposed as an alternative to screen-film mammography (SFM). The ability to separate and optimize the acquisition, storage, and display of images may allow greater visualization of breast cancers at equal or lower radiation doses, especially in younger women and those with denser breasts. This is a synopsis of a systematic review by the Blue Cross Blue Shield Association Technology Evaluation Center. This updated systematic review primarily incorporated the results of the ACR Imaging Network(R) Digital Mammographic Imaging Screening Trial (DMIST), which provided results on 42,760 asymptomatic women who underwent both FFDM and SFM and showed with reasonable certainty that there was no difference in the accuracy of the 2 modalities for asymptomatic women in general, with some advantages of FFDM in certain subgroups. There were no strong, new studies on the use of digital mammography compared with film mammography in a diagnostic population. However, the DMIST results indicated that tumors detected by FFDM, but not by SFM, were likely to be invasive carcinomas or medium-grade to high-grade ductal carcinoma in situ. On the basis of the suppositions that these are the cancers of greatest interest and the ones more likely to be found in a diagnostic population and that the diagnostic population may be younger on average than the screening population, it was concluded that there is sufficient evidence to support the use of FFDM for diagnostic purposes.

  7. Contemporary performativities and the imperative of participation in digital technologies

    Directory of Open Access Journals (Sweden)

    Gisela Cánepa Koch

    2015-01-01

    Full Text Available In a processual perspective of social life, technology works within discursive and action frames that make it possible. these frames provide meaning and legitimate technology but are also produced through technology and its uses. In other words, actions frames of an era are constitutive of and constituted by technology. this perspective follows a performative approach on digital technologies which allow the authors to problematize them in terms of their actors, discourses, and practices. On this way, the authors go beyond views that tend to dichotomize in order to understand issues of representation and power relations. Yet, what happens when actor’s performances and the performative force of their practices are no longer an aspect of their dynamics and configuration, but rather a normative force? In other words, what is at stake when actors and their performances are organized by performance as a mandate, that is, as a regime of truth? In a context where the principles of efficiency, effectiveness and efficacy are a mandate, there is a need to ask this sort of question, particularly in relation to the paradoxes it poses to participatory regimes that respond to the demands of neoliberal governmentality.

  8. 60 GHz 5-bit digital controlled phase shifter in a digital 40 nm CMOS technology without ultra-thick metals

    NARCIS (Netherlands)

    Gao, H.; Ying, K.; Matters-Kammerer, M.K.; Harpe, P.; Wang, B.; Liu, B.; Serdijn, W.A.; Baltus, P.G.M.

    2016-01-01

    A 5-bit digital controlled switch-type passive phase shifter realised in a 40 nm digital CMOS technology without ultra-thick metals for the 60 GHz Industrial, Scientific and Medical (ISM) band is presented. A patterned shielding with electromagnetic bandgap structure and a stacked metals method to

  9. Using Disruptive Technologies to Make Digital Connections: Stories of Media Use and Digital Literacy in Secondary Classrooms

    Science.gov (United States)

    Nowell, Shanedra D.

    2014-01-01

    This study focused on ways teachers and students in an urban high school used technologies often labeled as disruptive (i.e. social media and mobile phones) as learning and relationship building tools, inside and outside the classroom. In this teacher research study, secondary teachers discussed digital literacies, the digital divide, and digital…

  10. Using Disruptive Technologies to Make Digital Connections: Stories of Media Use and Digital Literacy in Secondary Classrooms

    Science.gov (United States)

    Nowell, Shanedra D.

    2014-01-01

    This study focused on ways teachers and students in an urban high school used technologies often labeled as disruptive (i.e. social media and mobile phones) as learning and relationship building tools, inside and outside the classroom. In this teacher research study, secondary teachers discussed digital literacies, the digital divide, and digital…

  11. [Application of digital earth technology in research of traditional Chinese medicine resources].

    Science.gov (United States)

    Liu, Jinxin; Liu, Xinxin; Gao, Lu; Wei, Yingqin; Meng, Fanyun; Wang, Yongyan

    2011-02-01

    This paper describes the digital earth technology and its core technology-"3S" integration technology. The advance and promotion of the "3S" technology provide more favorable means and technical support for Chinese medicine resources survey, evaluation and appropriate zoning. Grid is a mature and popular technology that can connect all kinds of information resources. The author sums up the application of digital earth technology in the research of traditional Chinese medicine resources in recent years, and proposes the new method and technical route of investigation in traditional Chinese medicine resources, traditional Chinese medicine zoning and suitability assessment by combining the digital earth technology and grid.

  12. Impact of Digital Tooth Preparation Evaluation Technology on Preclinical Dental Students' Technical and Self-Evaluation Skills.

    Science.gov (United States)

    Gratton, David G; Kwon, So Ran; Blanchette, Derek; Aquilino, Steven A

    2016-01-01

    The aim of this study was to evaluate the effect of digital tooth preparation imaging and evaluation technology on dental students' technical abilities, self-evaluation skills, and the assessment of their simulated clinical work. A total of 80 second-year students at one U.S. dental school were assigned to one of three groups: control (n=40), E4D Compare (n=20), and Sirona prepCheck (n=20). Students in the control group were taught by traditional teaching methodologies, and the technology-assisted groups received both traditional training and supplementary feedback from the corresponding digital system. Three outcomes were measured: faculty technical score, self-evaluation score, and E4D Compare scores at 0.30 mm tolerance. Correlations were determined between the groups' scores from visual assessment and self-evaluation and between the visual assessment and digital scores. The results showed that the visual assessment and self-evaluation scores did not differ among groups (p>0.05). Overall, correlations between visual and digital assessment scores were modest though statistically significant (5% level of significance). These results suggest that the use of digital tooth preparation evaluation technology did not impact the students' prosthodontic technical and self-evaluation skills. Visual scores given by faculty and digital assessment scores correlated moderately in only two instances.

  13. Medical image digital archive: a comparison of storage technologies

    Science.gov (United States)

    Chunn, Timothy; Hutchings, Matt

    1998-07-01

    A cost effective, high capacity digital archive system is one of the remaining key factors that will enable a radiology department to eliminate film as an archive medium. The ever increasing amount of digital image data is creating the need for huge archive systems that can reliably store and retrieve millions of images and hold from a few terabytes of data to possibly hundreds of terabytes. Selecting the right archive solution depends on a number of factors: capacity requirements, write and retrieval performance requirements, scaleability in capacity and performance, conformance to open standards, archive availability and reliability, security, cost, achievable benefits and cost savings, investment protection, and more. This paper addresses many of these issues. It compares and positions optical disk and magnetic tape technologies, which are the predominant archive mediums today. New technologies will be discussed, such as DVD and high performance tape. Price and performance comparisons will be made at different archive capacities, plus the effect of file size on random and pre-fetch retrieval time will be analyzed. The concept of automated migration of images from high performance, RAID disk storage devices to high capacity, NearlineR storage devices will be introduced as a viable way to minimize overall storage costs for an archive.

  14. Digital Control Technologies for Modular DC-DC Converters

    Science.gov (United States)

    Button, Robert M.; Kascak, Peter E.; Lebron-Velilla, Ramon

    2002-01-01

    Recent trends in aerospace Power Management and Distribution (PMAD) systems focus on using commercial off-the-shelf (COTS) components as standard building blocks. This move to more modular designs has been driven by a desire to reduce costs and development times, but is also due to the impressive power density and efficiency numbers achieved by today's commercial DC-DC converters. However, the PMAD designer quickly learns of the hidden "costs" of using COTS converters. The most significant cost is the required addition of external input filters to meet strict electromagnetic interference (MIAMI) requirements for space systems. In fact, the high power density numbers achieved by the commercial manufacturers are greatly due to the lack of necessary input filters included in the COTS module. The NASA Glenn Research Center is currently pursuing a digital control technology that addresses this problem with modular DC-DC converters. This paper presents the digital control technologies that have been developed to greatly reduce the input filter requirements for paralleled, modular DC-DC converters. Initial test result show that the input filter's inductor size was reduced by 75 percent, and the capacitor size was reduced by 94 percent while maintaining the same power quality specifications.

  15. Integration of the digital technologies in the teaching of astronomy

    Science.gov (United States)

    de Macedo, J. A.; Voelzke, M. R.

    2014-08-01

    This study presents results of a survey conducted at the Federal Institution of Education, Science and Technology in the North of Minas Gerais (IFNMG), and aimed to investigate the potential uses of interactive materials in the teaching of astronomy. Despite being part of official documents, proposals included in the curriculum of several states, and having contributed to human and technological development, astronomy is rarely taught adequately in the Brazilian basic education. When it is taught, it is with unsatisfactory results as presented by students and teachers as shown by several studies, such as those carried out by (Voelzke and Gonzaga, 2013). Digital technologies are commonly used by youth, but neglected by the majority of teachers. In this sense, a survey with the aim of pointing out the potential use of digital technologies in teaching astronomy was developed. An advanced course in astronomy was offered for participants with the goal to help them understand astronomical phenomena. The following steps were to be taken: i) analysis of the pedagogical projects (PPC) of the licenciates at the IFNMG, with its Campus Januária as research locus; ii) analysis of students' preconceptions about astronomy and digital technologies, identified by the application of an initial questionnaire; iii) preparation of the course taking into account the students' previous knowledge; iv) application of the education proposal developed under part-time presence modality, using various interactive tools; v) application and analysis of the final questionnaire. The test consisted of thirty-two students of physics, mathematics and biology and was conducted with the qualitative and quantitative methodology, combined with a content analysis. Among other results, it was verified that: (i) In the IFNMG only the licenciate-course in physics includes astronomy content diluted in various subjects of the curriculum; (ii) the analysis of the initial questionnaire showed even that group

  16. Malaysian Teachers' Conceptions and Uses of Digital Technology in English Writing Instruction: A Multiple Case Study

    Science.gov (United States)

    Mohamed Razali, Abu Bakar

    2013-01-01

    Very little is known about how teachers' "conceptualizations" of digital technology and their "uses" of the technology evolve and relate. Yet knowing about and understanding teachers' conceptions and uses of digital technology are essential for learning how teachers integrate it effectively for student learning. By applying…

  17. Barriers and Facilitators to Using Digital Technologies in the Cooperative Learning Model in Physical Education

    Science.gov (United States)

    Bodsworth, Hannah; Goodyear, Victoria A.

    2017-01-01

    Background: The influence of technology on children's everyday lives is significant in today's society, with children described as digital natives and/or the iGeneration. There are also a range of digital technologies available for use in education and a number of pedagogical approaches reported to support technology integration and pupil learning…

  18. How digital technologies, blended learning and MOOCs will impact the future of Higher Education

    OpenAIRE

    Morris, NP

    2014-01-01

    Digital technologies are revolutionizing all parts of society, including higher education. Universities are rapidly adapting to the prevalence of staff and student mobile devices, digital tools and services on campus, and are developing strategies to harness these technologies to enhance student learning. In this paper, I explore the use of digital technologies to support blended learning in universities, and discuss how massive open online courses (MOOCs) can be improved through better under...

  19. Digital Technology Corporation: Global Organizational Architecture for Sustained Competitive Advantage

    National Research Council Canada - National Science Library

    Clifford R Perry

    2013-01-01

    .... After reviewing the results of an extensive audit and analysis of Digital's current worldwide structure and strategy, Digital's Board of Directors approved a redesigned organizational architecture...

  20. Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference

    NARCIS (Netherlands)

    Ru, Zhiyu; Moseley, Niels A.; Klumperink, Eric A.M.; Nauta, Bram

    2009-01-01

    A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combina

  1. Digitally Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference

    NARCIS (Netherlands)

    Ru, Z.; Moseley, N.A.; Klumperink, Eric A.M.; Nauta, Bram

    2009-01-01

    Abstract—A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband i

  2. Specification for Digital Channel Selection Filters in a Bluetooth Capable HiperLAN/2 Receiver

    NARCIS (Netherlands)

    Hoeksema, Fokke; Schiphorst, Roel; Slump, Kees

    2002-01-01

    In this paper we first briefly describe how the analog part of the channel selection function for a HiperLAN/2 receiver can be used as part of the channel selection function for a Bluetooth receiver. Thereafter we proceed to specify the overall requirements for the Bluetooth channel selection functi

  3. Design and evaluation of a low-level RF control system analog/digital receiver for the ILC main Linacs

    Energy Technology Data Exchange (ETDEWEB)

    Mavric, Uros; Vidmar, Matjaz; Chase, Brian; /Fermilab

    2008-06-01

    The proposed RF distribution scheme for the two 15 km long ILC LINACs, uses one klystron to feed 26 superconducting RF cavities operating at 1.3 GHz. For a precise control of the vector sum of the signals coming from the SC cavities, the control system needs a high performance, low cost, reliable and modular multichannel receiver. At Fermilab we developed a 96 channel, 1.3 GHz analog/digital receiver for the ILC LINAC LLRF control system. In the paper we present a balanced design approach to the specifications of each receiver section, the design choices made to fulfill the goals and a description of the prototyped system. The design is tested by measuring standard performance parameters, such as noise figure, linearity and temperature sensitivity. Measurements show that the design meets the specifications and it is comparable to other similar systems developed at other laboratories, in terms of performance.

  4. Design and evaluation of a low-level RF control system analog/digital receiver for the ILC main LINACs

    Energy Technology Data Exchange (ETDEWEB)

    Mavric, Uros [Fermilab, P.O. Box 500, 60510 Batavia, IL (United States)], E-mail: mavric@fnal.gov; Chase, Brian [Fermilab, P.O. Box 500, 60510 Batavia, IL (United States); Vidmar, Matjaz [Faculty of Electrical Engineering in Ljubljana, Trzaska 25, 1000 Ljubljana (Slovenia)

    2008-08-21

    The proposed RF distribution scheme for the two 15 km long ILC LINACs uses one klystron to feed 26 superconducting RF cavities operating at 1.3 GHz. For a precise control of the vector sum of the signals coming from the SC cavities, the control system needs a high-performance, low-cost, reliable and modular multichannel receiver. At Fermilab we developed a 96-channel, 1.3 GHz analog/digital receiver for the ILC LINAC LLRF control system. In this paper we present a balanced design approach to the specifications of each receiver section, the design choices made to fulfill the goals and a description of the prototyped system. The design is tested by measuring standard performance parameters, such as noise figure, linearity and temperature sensitivity. Measurements show that the design meets the specifications and it is comparable to other similar systems developed at other laboratories, in terms of performance.

  5. Using Information and Communication Technology (ICT) to the Maximum: Learning and Teaching Biology with Limited Digital Technologies

    Science.gov (United States)

    Van Rooy, Wilhelmina S.

    2012-01-01

    Background: The ubiquity, availability and exponential growth of digital information and communication technology (ICT) creates unique opportunities for learning and teaching in the senior secondary school biology curriculum. Digital technologies make it possible for emerging disciplinary knowledge and understanding of biological processes…

  6. Guest Editors’ Introduction: Advances in Interactive Digital Entertainment Technologies

    Directory of Open Access Journals (Sweden)

    Frederick Li

    2009-04-01

    Full Text Available With the significant development of digital technologies in recent years, we are seeing an increasing number of applications of these technologies, in particular in the entertainment domain. They may include computer games, e-learning, high- definition and interactive TVs, and virtual environments. The development of these applications typically involves the integration of existing technologies as well as the development of new technologies.The first International Workshop on Digital Entertainment Technologies 2008 (IDET’08 was held at Lanzhou University, China, in July 2008, in conjunction with the first IEEE International Conference on Ubi-media Computing (U-Media’08. This workshop was an initial effort to review various technological issues and challenges in digital entertainments. A special emphasis was on issues that are relevant to or supporting the dynamic interactions between users and applications. This special issue collects the extended version of some of the best papers presented in IDET’08 and relevant keynote papers presented in U-Media’08.This special issue includes six papers covering some of the recent technological advances in digital entertainments. These papers can be roughly divided into three groups. The first group of two papers addresses networking issues of digital entertainments. The article by Wah and Sat (of University of Illinois, Urbana-Champaign, U.S.A. describes the authors’ work on real-time VoIP (voice over-IP systems that can achieve high perceptual conversational quality. It focuses on the fundamental understanding of conversational quality and its trade-offs among the design of speech codecs and strategies for network control, playout scheduling, and loss concealments. The article by Ye, Li, and Chen (of City University of Hong Kong, Hong Kong presents an adaptive algorithm called “SPF-A*” for searching multimedia files in heterogeneous mobile P2P network environments in order for these

  7. Exploitation of Information Processing Technologies to Extend Digital Library Applications

    Directory of Open Access Journals (Sweden)

    Jian-Hua Yeh、Jia-Yanh Chang、Yen-Jen Oyan

    1999-04-01

    Full Text Available

    頁次:1-11

    This paper discusses exploitation of information processing technologies to extend digital library applications to a new dimension. The discussion focuses on the following three information processing technologies.

    l. information extraction.

    2. deductive inference.

    3. data mining.

    The most significant applications are discovery and derivation of new information and knowledge. This paper discusses how these information processing technologies can be exploited to complement the capabilities of human beings in the digital library domain. The tasks that the developed information processing utilities perform are simple and tedious intelligent information processing. However, because a digital library contains a large quantity of contents, it is common that human beings can hardly carry out such tasks exhaustively. As a result, a great amount of information and knowledge may remain undiscovered without the assistance of assistance of such utilities. On the other hands, with the developed information processing utilities, human being are the released form performing

  8. The Impact of Interference on GNSS Receiver Observables – A Running Digital Sum Based Simple Jammer Detector

    Directory of Open Access Journals (Sweden)

    M. Z. H. Bhuiyan

    2014-09-01

    Full Text Available A GNSS-based navigation system relies on externally received information via a space-based Radio Frequency (RF link. This poses susceptibility to RF Interference (RFI and may initiate failure states ranging from degraded navigation accuracy to a complete signal loss condition. To guarantee the integrity of the received GNSS signal, the receiver should either be able to function in the presence of RFI without generating misleading information (i.e., offering a navigation solution within an accuracy limit, or the receiver must detect RFI so that some other means could be used as a countermeasure in order to ensure robust and accurate navigation. Therefore, it is of utmost importance to identify an interference occurrence and not to confuse it with other signal conditions, for example, indoor or deep urban canyon, both of which have somewhat similar impact on the navigation performance. Hence, in this paper, the objective is to investigate the effect of interference on different GNSS receiver observables in two different environments: i. an interference scenario with an inexpensive car jammer, and ii. an outdoor-indoor scenario without any intentional interference. The investigated observables include the Automatic Gain Control (AGC measurements, the digitized IF (Intermediate Frequency signal levels, the Delay Locked Loop and the Phase Locked Loop discriminator variances, and the Carrier-to-noise density ratio (C/N0 measurements. The behavioral pattern of these receiver observables is perceived in these two different scenarios in order to comprehend which of those observables would be able to separate an interference situation from an indoor scenario, since in both the cases, the resulting positioning accuracy and/or availability are affected somewhat similarly. A new Running Digital Sum (RDS -based interference detection method is also proposed herein that can be used as an alternate to AGC-based interference detection. It is shown in this paper

  9. Reconfigurable Digital Coherent Receiver for Hybrid Optical Fiber/Wireless Metro-Access Networks

    DEFF Research Database (Denmark)

    Arlunno, Valeria; Guerrero Gonzalez, Neil; Caballero Jambrina, Antonio;

    Single reconfigurable DSP coherent receiver is experimentally demonstrated for mixed-format and bit-rates including QPSK, OFDM, IR-UWB for wireline and wireless signal types. Successful transmission and detection over a deployed fiber link is achieved.......Single reconfigurable DSP coherent receiver is experimentally demonstrated for mixed-format and bit-rates including QPSK, OFDM, IR-UWB for wireline and wireless signal types. Successful transmission and detection over a deployed fiber link is achieved....

  10. Extremely high frequency (EHF) satellite communications (SATCOM) technology-transmitters and receivers

    Science.gov (United States)

    Raue, Jorg E.

    1983-10-01

    During the past three years, interest in satellite communications in the frequency bands above Ku-band has expanded dramatically. As a result, a number of key technology developments, targeted to meet specific next generation spaceborne needs, were undertaken. The state-of-the-art in solid state power transmitters and low noise receivers, including critical passive component technology, is presented. This includes filters as well as a series of rugged high performance ferrite components such as isolators, circulators and latching switches.

  11. Digital Technology in Education: Towards New Inclusive Practices

    DEFF Research Database (Denmark)

    Jönsson, Lise Høgh

    2017-01-01

    for new inclusive practices. The main theoretical argument derives from the work of French sociologist Pierre Bourdieu. Bourdieu argues that we act upon the world with our habitus, i.e. dispositions created due to previous experiences working as a matrix of perceptions, assumptions and actions....... The habitus is used in the field to engage in struggles for symbolic capital and, thus, provides better opportunities for those whose habitus matches the particular field. In this research, the education facilities are considered social fields, where particular people have better opportunities than others....... Using Bourdieu’s theoretical framework, it becomes possible to explain how children and people with learning disabilities are able to strengthen their position by the use of digital technology. This theoretical framework is enhanced by theories of empowerment as any improvement in the participation...

  12. [Development and prospect of digital technology in the field of prosthodontics].

    Science.gov (United States)

    Zhang, F Q

    2016-04-01

    The development of digital technology is gradually changing clinical practice and laboratory procedure of prosthodontics. After decades of exploration and development, the modern digital technology has been perfectly merged with prosthodontics and created a brand new treatment mode. The application of digital impression, digital design and digital processing has changed the way we treat patients and the way we communicate with patients. The data storage also provides a basis for long-term follow-up. The establishment of digital remote system, transferring data through internet, has improved communication in dental technique, tracing analysis of patient's condition, sharing and management of medical data, and popularization and promotion of knowledge. Digital technology promoted the development of prosthodontics in the direction of more precision, more convenience, more efficiency and more simulation in functional recovery, which will be one of the development directions of dentistry and even the medical science in the future.

  13. Reconfigurable digital receiver for 8PSK subcarrier multiplexed and 16QAM single carrier phase‐modulated radio over fiber links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Yu, Xianbin

    2011-01-01

    A reconfigurable digital receiver based on the k‐means algorithm is proposed for phase‐modulated subcarrier multiplexed (SCM) and quadrature amplitude‐modulated single carrier, phase‐modulated radio‐over‐fiber links. We report successful demodulation after 40 km single mode fiber transmission...... with three 50 Mbaud 8PSK SCM signals and a 312.5 Mbaud 16QAM single carrier. © 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53:1015–1018, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.25905...

  14. Use of Digital Image Technology to 'Clearly' Depict Global Change

    Science.gov (United States)

    Molnia, B. F.; Carbo, C. L.

    2014-12-01

    Earth is dynamic and beautiful. Understanding why, when, how, and how fast its surface changes yields information and serves as a source of inspiration. The artistic use of geoscience information can inform the public about what is happening to their planet in a non-confrontational and apolitical way. While individual images may clearly depict a landscape, photographic comparisons are necessary to clearly capture and display annual, decadal, or century-scale impacts of climate and environmental change on Earth's landscapes. After years of effort to artistically communicate geoscience concepts with unenhanced individual photographs or pairs of images, the authors have partnered to maximize this process by using digital image enhancement technology. This is done, not to manipulate the inherent artistic content or information content of the photographs, but to insure that the comparative photo pairs produced are geometrically correct and unambiguous. For comparative photography, information-rich historical photographs are selected from archives, websites, and other sources. After determining the geographic location from which the historical photograph was made, the original site is identified and eventually revisited. There, the historical photos field of view is again photographed, ideally from the original location. From nearly 250 locations revisited, about 175 pairs have been produced. Every effort is made to reoccupy the original historical site. However, vegetation growth, visibility reduction, and co-seismic level change may make this impossible. Also, inherent differences in lens optics, camera construction, and image format may result in differences in the geometry of the new photograph when compared to the old. Upon selection, historical photos are cleaned, contrast stretched, brightness adjusted, and sharpened to maximize site identification and information extraction. To facilitate matching historical and new images, digital files of each are overlain in

  15. Research of Digital Manufacturing Technology Application on Ultra-precision Optical Workpiece Machining

    Institute of Scientific and Technical Information of China (English)

    HE Daxing

    2006-01-01

    Digital manufacturing technology can be used in optical field to solve many problems caused by traditional machining. According to the characters of digital manufacturing and the practical applications of ultra-precision machining, the process of digital ultra-precision machining and its technical contents were presented in this paper. In the conclusions, it was stated that the digitalization of ultra-precision machining will be an economical and efficient way for the production of new sorts of optical workpieces.

  16. The impact of digital technology on psychological treatments and their dissemination.

    Science.gov (United States)

    Fairburn, Christopher G; Patel, Vikram

    2017-01-01

    The psychological treatment of mental health problems is beginning to undergo a sea-change driven by the widespread availability of digital technology. In this paper we provide an overview of the developments to date and those in the pipeline. We describe the various uses of digital interventions and consider their likely impact on clinical practice, clinical services and the global dissemination of psychological treatments. We note the importance of online clinics, blended treatment, digital assessment and digital training.

  17. A 16 b 2 GHz digital-to-analog converter in 0.18 μm CMOS with digital calibration technology

    Science.gov (United States)

    Weidong, Yang; Jiandong, Zang; Tiehu, Li; Pu, Luo; Jie, Pu; Ruitao, Zhang; Chao, Chen

    2015-10-01

    This paper presents a 16-bit 2 GSPS digital-to-analog converter (DAC) in 0.18 μm CMOS technology. This DAC is implemented using time division multiplex access system architecture in the digital domain. The input data is received with a two-channel LVDS interface. The DLL technology is introduced to meet the timing requirements between phases of the LVDS data and the data sampling clock. A FIFO is designed to absorb the phase difference between the data clock and DAC system clock. A delay controller is integrated to adjust the phase relationship between the high speed digital clock and analog clock, obtaining a sampling rate of 2 GSPS. The current source mismatch at higher bits is calibrated in the digital domain. Test results show that the DAC achieves 74.02 dBC SFDR at analog output of 36 MHz, and DNL less than ±2.1 LSB & INL less than ±4.3 LSB after the chip is calibrated.

  18. Teaching with technology: automatically receiving information from the internet and web.

    Science.gov (United States)

    Wink, Diane M

    2010-01-01

    In this bimonthly series, the author examines how nurse educators can use the Internet and Web-based computer technologies such as search, communication, and collaborative writing tools, social networking and social bookmarking sites, virtual worlds, and Web-based teaching and learning programs. This article presents information and tools related to automatically receiving information from the Internet and Web.

  19. Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

    Institute of Scientific and Technical Information of China (English)

    Wang; Junbiao; Liu; Chuang

    2007-01-01

    The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.

  20. Design and simulation of stratified probability digital receiver with application to the multipath communication

    Science.gov (United States)

    Deal, J. H.

    1975-01-01

    One approach to the problem of simplifying complex nonlinear filtering algorithms is through using stratified probability approximations where the continuous probability density functions of certain random variables are represented by discrete mass approximations. This technique is developed in this paper and used to simplify the filtering algorithms developed for the optimum receiver for signals corrupted by both additive and multiplicative noise.

  1. 47 CFR 15.122 - Closed caption decoder requirements for digital television receivers and converter boxes.

    Science.gov (United States)

    2010-10-01

    ... television receivers and converter boxes. 15.122 Section 15.122 Telecommunication FEDERAL COMMUNICATIONS...). (i) Predefined window and pen styles. Predefined Window Style and Pen Style ID's may be provided in the DefineWindow command. At a minimum, decoders should implement Predefined Window Attribute Style...

  2. Cognitive digital receiver for burst mode phase modulated radio over fiber links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Tafur Monroy, Idelfonso

    2010-01-01

    A novel cognitive receiver for modulation format recognition with reconfigurable carrier recovery scheme is proposed and experimentally demonstrated for phase modulated radio-over-fibre links. Demodulation of burst-mode mixed modulation formats (PSK and QAM) is demonstrated after 40km...

  3. The Impact of Digital Video Technology on Production: The Case of "American Gothic."

    Science.gov (United States)

    Fink, Edward J.

    1997-01-01

    Opines that the study of video production is important in better understanding the aural/visual aspects of television, especially since television production is undergoing a digital revolution. Assesses the impact of new technologies by examining a "cutting-edge" program, "American Gothic." Finds that digital technology offers…

  4. Technology Knowledge Self-Assessment and Pre-Test Performance among Digital Natives

    Science.gov (United States)

    Nelms, Keith R.

    2015-01-01

    According to education pundits, traditional-age college students are "digital natives" inherently savvy in digital technology due to their constant exposure to technology from an early age. This widely held meme is at odds with observation in the college classroom. In this research, college students in an introductory information…

  5. Organizational Influences in Technology Adoption Decisions: A Case Study of Digital Libraries

    Science.gov (United States)

    Oguz, Fatih

    2016-01-01

    The purpose of this study was to understand the organizational level decision factors in technology adoption in the context of digital libraries. A qualitative case study approach was used to investigate the adoption of a specific technology, XML-based Web services, in digital libraries. Rogers' diffusion of innovations and Wenger's communities of…

  6. Comic Relief: Graduate Students Address Multiple Meanings for Technology Integration with Digital Comic Creation

    Science.gov (United States)

    Sockman, Beth Rajan; Sutton, Rhonda; Herrmann, Michele

    2016-01-01

    This study determined the usefulness of digital comic creation with 77 graduate students in a teacher technology course. Students completed an assigned reading and created digital comics that addressed technology integration concerns in the schools and society. Using practical action research, 77 student-created comics were analyzed. The findings…

  7. Digital Technology and the Culture of Teaching and Learning in Higher Education

    Science.gov (United States)

    Lai, Kwok-Wing

    2011-01-01

    This paper discusses how the use of digital technologies may support a shift of cultural practices in teaching and learning, to better meet the needs of 21st century higher education learners. A brief discussion of the changing needs of the learners is provided, followed by a review of the overall impact of digital technologies on teaching and…

  8. Comic Relief: Graduate Students Address Multiple Meanings for Technology Integration with Digital Comic Creation

    Science.gov (United States)

    Sockman, Beth Rajan; Sutton, Rhonda; Herrmann, Michele

    2016-01-01

    This study determined the usefulness of digital comic creation with 77 graduate students in a teacher technology course. Students completed an assigned reading and created digital comics that addressed technology integration concerns in the schools and society. Using practical action research, 77 student-created comics were analyzed. The findings…

  9. Embracing Digital Technologies in Classroom Practice: The Impact of Teacher Identity

    Science.gov (United States)

    Abbott, Rosemary

    2016-01-01

    It is often perceived that learning in 21st century classrooms will involve extensive use of digital technologies. This paper, based on a qualitative research investigation at a private girls' college in Melbourne, explores the impact of teacher subjectivities on the need to change through the integration of digital technologies into classroom…

  10. Organizational Influences in Technology Adoption Decisions: A Case Study of Digital Libraries

    Science.gov (United States)

    Oguz, Fatih

    2016-01-01

    The purpose of this study was to understand the organizational level decision factors in technology adoption in the context of digital libraries. A qualitative case study approach was used to investigate the adoption of a specific technology, XML-based Web services, in digital libraries. Rogers' diffusion of innovations and Wenger's communities of…

  11. How Digital Technologies, Blended Learning and MOOCs Will Impact the Future of Higher Education

    Science.gov (United States)

    Morris, Neil P.

    2014-01-01

    Digital technologies are revolutionizing all parts of society, including higher education. Universities are rapidly adapting to the prevalence of staff and student mobile devices, digital tools and services on campus, and are developing strategies to harness these technologies to enhance student learning. In this paper, I explore the use of…

  12. Exploring How Digital Media Technology Can Foster Saudi EFL Students' English Language Learning

    Science.gov (United States)

    Altawil, Abdulmohsin

    2016-01-01

    Digital media technology has become an integral part of daily life for almost all young students, and for the majority of Saudi EFL (English as a Foreign Language) students. Digital media technology may not be limited to one or two kinds; it has various types such as software and programs, devices, application, websites, social media tools, etc.…

  13. Teachers' Use of Digital Technology in Secondary Music Education: Illustrations of Changing Classrooms

    Science.gov (United States)

    Wise, Stuart; Greenwood, Janinka; Davis, Niki

    2011-01-01

    The music industry in the 21st century uses digital technology in a wide range of applications including performance, composition and in recording and publishing. Much of this digital technology is freely available via downloads from the internet, as part of software included with computers when they are purchased and via applications that are…

  14. A Digital Ecosystem of Diabetes Data and Technology

    Science.gov (United States)

    Heintzman, Nathaniel D.

    2015-01-01

    The management of type 1 diabetes (T1D) ideally involves regimented measurement of various health signals; constant interpretation of diverse kinds of data; and consistent cohesion between patients, caregivers, and health care professionals (HCPs). In the context of myriad factors that influence blood glucose dynamics for each individual patient (eg, medication, activity, diet, stress, sleep quality, hormones, environment), such coordination of self-management and clinical care is a great challenge, amplified by the routine unavailability of many types of data thought to be useful in diabetes decision-making. While much remains to be understood about the physiology of diabetes and blood glucose dynamics at the level of the individual, recent and emerging medical and consumer technologies are helping the diabetes community to take great strides toward truly personalized, real-time, data-driven management of this chronic disease. This review describes “connected” technologies—such as smartphone apps, and wearable devices and sensors—which comprise part of a new digital ecosystem of data-driven tools that can link patients and their care teams for precision management of diabetes. These connected technologies are rich sources of physiologic, behavioral, and contextual data that can be integrated and analyzed in “the cloud” for research into personal models of glycemic dynamics, and employed in a multitude of applications for mobile health (mHealth) and telemedicine in diabetes care. PMID:26685994

  15. A programmable gain amplifier with digitally assisted DC offset calibration for a direct-conversion WLAN receiver

    Institute of Scientific and Technical Information of China (English)

    Yao Xiaocheng; Gong Zheng; Shi Yin

    2012-01-01

    This paper presents a programmable gain amplifier (PGA) circuit with a digitally assisted DC offset cancellation (DCOC) scheme for a direct conversion WLAN receiver.Implemented in a standard 0.13-μm CMOS process,the PGA occupies 0.39 mm2 die area and dissipates 6.5 mW power from a 1.2 V power supply.By using a single loop single digital-to-analog converter (DAC) mixed signal DC offset cancellation topology,the minimum DCOC settling time achieved is as short as 1.6 μs with the PGA gain ranging from-8 to 54 dB in a 2 dB step.The DCOC loop utilizes a segmented DAC structure to lower the design complexity without sacrificing accuracy and a digital control algorithm to dynamically set the DCOC loop to fast or normal response mode,making the PGA circuit in compliance with the targeted WLAN specifications.

  16. Prostate: registration of digital histopathologic images to in vivo MR images acquired by using endorectal receive coil.

    Science.gov (United States)

    Ward, Aaron D; Crukley, Cathie; McKenzie, Charles A; Montreuil, Jacques; Gibson, Eli; Romagnoli, Cesare; Gomez, Jose A; Moussa, Madeleine; Chin, Joseph; Bauman, Glenn; Fenster, Aaron

    2012-06-01

    To develop and evaluate a technique for the registration of in vivo prostate magnetic resonance (MR) images to digital histopathologic images by using image-guided specimen slicing based on strand-shaped fiducial markers relating specimen imaging to histopathologic examination. The study was approved by the institutional review board (the University of Western Ontario Health Sciences Research Ethics Board, London, Ontario, Canada), and written informed consent was obtained from all patients. This work proposed and evaluated a technique utilizing developed fiducial markers and real-time three-dimensional visualization in support of image guidance for ex vivo prostate specimen slicing parallel to the MR imaging planes prior to digitization, simplifying the registration process. Means, standard deviations, root-mean-square errors, and 95% confidence intervals are reported for all evaluated measurements. The slicing error was within the 2.2 mm thickness of the diagnostic-quality MR imaging sections, with a tissue block thickness standard deviation of 0.2 mm. Rigid registration provided negligible postregistration overlap of the smallest clinically important tumors (0.2 cm(3)) at histologic examination and MR imaging, whereas the tested nonrigid registration method yielded a mean target registration error of 1.1 mm and provided useful coregistration of such tumors. This method for the registration of prostate digital histopathologic images to in vivo MR images acquired by using an endorectal receive coil was sufficiently accurate for coregistering the smallest clinically important lesions with 95% confidence.

  17. Principles of transistor circuits introduction to the design of amplifiers, receivers and digital circuits

    CERN Document Server

    Amos, S W

    1990-01-01

    Principles of Transistor Circuits, Seventh Edition discusses the fundamental concepts of transistor circuits. The book is comprised of 16 chapters that cover amplifiers, oscillators, and generators. Chapter 1 discusses semiconductors and junction nodes, while Chapter 2 covers the basic principles of transistors. The subsequent chapters focus on amplifiers, where one of the chapters discusses bias and D.C. The book also talks about sinusoidal oscillators and covers modulators, demodulators, mixers, and receivers. Chapters 13 and 14 discuss pulse generators and sawtooth generators, respectively.

  18. VLSI Structure for an All Digital Receiver for CDMA PABX Handset

    Institute of Scientific and Technical Information of China (English)

    ZhouShidong; BiGuangguo

    1995-01-01

    In this paper,a VLSI architecture of a CDMA receiver is put forward for wirelesss PABX handset.To meet the critically low cost and power consumption requirement with neglectable per-formance degradation,some new techniques are employed to reduce hardware complexity,including base band processing,chip-rate sampling,low ADC resolution,absolute value detector,double branch acquisition ,and modified carrier phase compensation.Performance of experimental system fits well with theoretical predition ,and the practical SNR lose compared with ideal reception is about 2-3dB.

  19. Advantages Of Implementing Digital Receivers In Field Programmable Gate Arrays (FPGA)

    CERN Document Server

    Bremec, S; Mavric, U

    2003-01-01

    Today’s state-of-the-art FPGA technology allows designers to satisfy almost any demand for high-speed data processing needed in DSP applications and fast data transfers. Dedicated FPGA resources are used in DSP applications to perform down conversion, filtering and data formatting. New trends in system architecture favor serial data transfer rather than parallel by using FPGA’s internal resources, BRAMs, high speed serial IOs and hard core processors.

  20. Hybrid-integrated coherent receiver using silica-based planar lightwave circuit technology

    Science.gov (United States)

    Kim, Jong-Hoi; Choe, Joong-Seon; Choi, Kwang-Seong; Youn, Chun-Ju; Kim, Duk-Jun; Jang, Sun-Hyok; Kwon, Yong-Hwan; Nam, Eun-Soo

    2011-12-01

    A hybrid-integrated coherent receiver module has been achieved using flip-chip bonding technology, consisting of a silica-based 90°-hybrid planar lightwave circuit (PLC) platform, a spot-size converter integrated waveguide photodiode (SSC-WG-PD), and a dual-channel transimpedance amplifier (TIA). The receiver module shows error-free operation up to 40Gb/s and OSNR sensitivity of 11.5 dB for BER = 10-3 at 25 Gb/s.

  1. The Relationship Between Digital Technology Experience, Daily Media Exposure and Working Memory Capacity

    Directory of Open Access Journals (Sweden)

    Muhterem DİNDAR

    2016-06-01

    Full Text Available Today’s youngsters interact with digital technologies to a great extent which leads scholars to question the influence of this exposure on human cognitive structure. Through resorting to digital nativity assumptions, it is presumed that cognitive architecture of the youth may change in accordance with digital technology use. In this regard, the current study investigated the relationship between digital technology experience, daily media exposure and working memory capacity of so-called digital native participants. A total of 572 undergraduate students responded to self-report measures, which addressed years of experience for 7 different digital devices and the daily time spent for 14 different digital activities. Participants’ working memory capacity was measured through the Computation Span and the Dot Matrix Test. While the former was used to measure the phonological loop capacity, the latter was used to address the visuo-spatial sketchpad capacity. Correlational analyses revealed that neither the phonological loop capacity nor the visuo-spatial sketchpad capacity was related to digital technology experience and daily media exposure. Thus, the transformative contribution of digital technology experience to human cognitive architecture could not be observed through the current measures

  2. VLSI Implementation of Novel Class of High Speed Pipelined Digital Signal Processing Filter for Wireless Receivers

    Directory of Open Access Journals (Sweden)

    Rozita Teymourzadeh

    2010-01-01

    Full Text Available Problem statement: The need for high performance transceiver with high Signal to Noise Ratio (SNR has driven the communication system to utilize latest technique identified as over sampling systems. It was the most economical modulator and decimation in communication system. It has been proven to increase the SNR and is used in many high performance systems such as in the Analog to Digital Converter (ADC for wireless transceiver. Approach: This research presented the design of the novel class of decimation and its VLSI implementation which was the sub-component in the over sampling technique. The design and realization of main unit of decimation stage that was the Cascaded Integrator Comb (CIC filter, the associated half band filters and the droop correction are also designed. The Verilog HDL code in Xilinx ISE environment has been derived to describe the proposed advanced CIC filter properties. Consequently, Virtex-II FPGA board was used to implement and test the design on the real hardware. The ASIC design implementation was performed accordingly and resulted power and area measurement on chip core layout. Results: The proposed design focused on the trade-off between the high speed and the low power consumption as well as the silicon area and high resolution for the chip implementation which satisfies wireless communication systems. The synthesis report illustrates the maximum clock frequency of 332 MHz with the active core area of 0.308×0.308 mm2. Conclusion: It can be concluded that VLSI implementation of proposed filter architecture is an enabler in solving problems that affect communication capability in DSP application.

  3. The Design of A Digital Family Multi-Service System Based on Triple-Play Technology

    Directory of Open Access Journals (Sweden)

    Yong Liu

    2013-04-01

    Full Text Available Under the background of three-net fusion, this study introduces a design of digital home multi-service system and elaborates from the perspective of digital TV broadcasting operation platform, interactive TV operation platform, home gateway and digital TV home multi-service terminals. This design is aimed to promote the two-way transformation of cable digital Television and the construction of operation platform. This will effectively help to accelerate the development of digital home service and broadcast television technology in Wujin.

  4. Application of the Wireless Digital Transmission Technology in Remote ECG Monitoring System

    Institute of Scientific and Technical Information of China (English)

    Xu,Lixin; Li,Qingliang; Chen,Zhen; Qi,Xinbo; Zhang,Xincheng

    2005-01-01

    Heart disease is one of the main diseases menace human' s health. The limited monitoring ability and limited serving ability are shortcomings of the existing remote ECG (electrocardiograph) monitoring system. It is practical to bring ECG monitoring from hospital to home. A new method is introduced that the application of wireless digital transmission technology in remote ECG monitoring system. In the system, the portable ECG monitoring device to collect and transmit patient""s electrocardiogram signals and the device to transmit and receive ECG signals are designed by using the PTR2000. The method solves the remote collection and transmission of patient's electrocardiogram signals, and creates the condition of the transmitting of patient"" s electrocardiogram signals through the Broadband network.

  5. Application of the Wireless Digital Transmission Technology in Remote ECG Monitoring System

    Institute of Scientific and Technical Information of China (English)

    Xu,Lixin; Li,Qingliang; Chen,Zhen; Qi,Xinbo; Zhang,Xincheng

    2005-01-01

    Heart disease is one of the main diseases menace human's health. The limited monitoring ability and limited serving ability are shortcomings of the existing remote ECG (electrocardiograph) monitoring system. It is practical to bring ECG monitoring from hospital to home. A new method is introduced that the application of wireless digital transmission technology in remote ECG monitoring system. In the system, the portable ECG monitoring device to collect and transmit patient's electrocardiogram signals and the device to transmit and receive ECG signals are designed by using the PTR2000. The method solves the remote collection and transmission of patient s electrocardiogram signals, and creates the condition of the transmitting of patient's electrocardiogram signals through the Broadband network.

  6. Power optimization of digital baseband WCDMA receiver components on algorithmic and architectural level

    Directory of Open Access Journals (Sweden)

    M. Schämann

    2008-05-01

    Full Text Available High data rates combined with high mobility represent a challenge for the design of cellular devices. Advanced algorithms are required which result in higher complexity, more chip area and increased power consumption. However, this contrasts to the limited power supply of mobile devices.

    This presentation discusses the application of an HSDPA receiver which has been optimized regarding power consumption with the focus on the algorithmic and architectural level. On algorithmic level the Rake combiner, Prefilter-Rake equalizer and MMSE equalizer are compared regarding their BER performance. Both equalizer approaches provide a significant increase of performance for high data rates compared to the Rake combiner which is commonly used for lower data rates. For both equalizer approaches several adaptive algorithms are available which differ in complexity and convergence properties. To identify the algorithm which achieves the required performance with the lowest power consumption the algorithms have been investigated using SystemC models regarding their performance and arithmetic complexity. Additionally, for the Prefilter Rake equalizer the power estimations of a modified Griffith (LMS and a Levinson (RLS algorithm have been compared with the tool ORINOCO supplied by ChipVision. The accuracy of this tool has been verified with a scalable architecture of the UMTS channel estimation described both in SystemC and VHDL targeting a 130 nm CMOS standard cell library.

    An architecture combining all three approaches combined with an adaptive control unit is presented. The control unit monitors the current condition of the propagation channel and adjusts parameters for the receiver like filter size and oversampling ratio to minimize the power consumption while maintaining the required performance. The optimization strategies result in a reduction of the number of arithmetic operations up to 70% for single components which leads to an

  7. Semantic Web Technologies for Digital Libraries: From Libraries to Social Semantic Digital Libraries (SSDL), Over Semantic Digital Libraries (SDL)

    OpenAIRE

    Alotaibi, Sara

    2010-01-01

    Digital libraries have been an important source of information throughout the history of mankind. It has been present in our societies in different forms. Notably, traditional libraries have found their on the desktops of internet users. They have taken the shape of semantic digital libraries, which are accessible at any time, and accordingly provide a more meaningful search. This paper further discusses social semantic digital libraries that also incorporate the social and collaborative aspect.

  8. Digital manufacturing-the development direction of the manufacturing technology in the 21st century

    Institute of Scientific and Technical Information of China (English)

    XIONG You-lun; YIN Zhou-ping

    2006-01-01

    After introducing the concepts of digital manufacturing technology,the discipline framework of digital manufacturing is presented in the paper by discussing its basic concept,theory foundation,key technology and scientific problems in detail.As the core of the advanced manufacturing technology,digital manufacturing is gradually becoming the main manufacturing technology of the twenty-first century.Firstly,the main features of digital manufacturing are indicated and its key supporting technologies are investigated by grouping them into four levels related to product development, numerical control, production management,and enterprise collaboration,respectively.Moreover,the existing problems in the research on the multi-discipline theory foundation of digital manufacturing such as manufacturing informatics, computational manufacturing,and manufacturing intelligence,are also indicated.Then,the core scientific problems of digital manufacturing are discussed in depth,which focuses on digitization of manufacturing information,modeling of manufacturing constraints,high-speed and high-precision numerical control theory,and Internet-based collaboration and integration.Lastly, the development trends and application perspectives of digital manufacturing are concluded.

  9. The Touch Pad Body: A Generative Transcultural Digital Device Interrupting Received Ideas and Practices in Aboriginal Health

    Directory of Open Access Journals (Sweden)

    Michael Christie

    2014-05-01

    Full Text Available Yolŋu Aboriginal understandings of the body, health, life and sickness, and roles their ancestral epistemologies and knowledge practices play in making agreement have seldom been taken seriously in the biomedical world. In this paper, we describe how insights developed in three different cross-cultural collaborative transdisciplinary research projects led to the design of a digital device aimed at intervening in communicative practices around body, health, life and sickness, interrupting the received practices and assumptions on both sides of the practitioner-client divide. The interrupting device slows down and opens up communication practices potentially leading to mutual understanding, collective agreement making, and bottom-up changes in remote Aboriginal health policy and practice.

  10. An autonomous receiver/digital signal processor applied to ground-based and rocket-borne wave experiments

    Science.gov (United States)

    Dombrowski, M. P.; LaBelle, J.; McGaw, D. G.; Broughton, M. C.

    2016-07-01

    The programmable combined receiver/digital signal processor platform presented in this article is designed for digital downsampling and processing of general waveform inputs with a 66 MHz initial sampling rate and multi-input synchronized sampling. Systems based on this platform are capable of fully autonomous low-power operation, can be programmed to preprocess and filter the data for preselection and reduction, and may output to a diverse array of transmission or telemetry media. We describe three versions of this system, one for deployment on sounding rockets and two for ground-based applications. The rocket system was flown on the Correlation of High-Frequency and Auroral Roar Measurements (CHARM)-II mission launched from Poker Flat Research Range, Alaska, in 2010. It measured auroral "roar" signals at 2.60 MHz. The ground-based systems have been deployed at Sondrestrom, Greenland, and South Pole Station, Antarctica. The Greenland system synchronously samples signals from three spaced antennas providing direction finding of 0-5 MHz waves. It has successfully measured auroral signals and man-made broadcast signals. The South Pole system synchronously samples signals from two crossed antennas, providing polarization information. It has successfully measured the polarization of auroral kilometric radiation-like signals as well as auroral hiss. Further systems are in development for future rocket missions and for installation in Antarctic Automatic Geophysical Observatories.

  11. The emergent role of digital technologies in the Circular Economy: A review

    DEFF Research Database (Denmark)

    Pagoropoulos, Aris; Pigosso, Daniela Cristina Antelmi; McAloone, Tim C.

    2017-01-01

    literature, is the concept of Circular Economy. Circular Economy is characterized as an economy that is restorative and regenerative by design and is attracting significant attention from researchers and policy makers alike. In light of the recent proliferation of digital technologies such as Big Data...... and the Internet of Things, this article attempts to identify how can digital technologies support the transition to Circular Economy. This article conducted a systematic review of the literature based on a review protocol, in an effort to evaluate the application of key digital technologies in Circular Economy...

  12. Technology qualification of an ambient pressure subsea cryogenic pipeline for offshore LNG loading and receiving terminals

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Afzal; Viteri, Martha; D' Angelo, Luis [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil); Prescott, Neal; Zhang, Jeff [Fluor Corporation, Irving, TX (Brazil)

    2009-07-01

    A project that deploys new technologies need to be confident that the technology can be implemented successfully and will perform reliably as designed. New technology is critical to industry, especially where such technology is a project enable without the existence of a backup solution, but also for projects where such technologies bring potential benefits such as technical, economic, schedule, and environmental improvements. DNV developed and has been implementing for many years a systematic, risk based technology qualification process as described in DNV RP-A203, qualification procedures for new technology. One of the major objectives of a formal technology qualification process is to ensure that risks are properly addressed. The DNV process includes several levels of technology qualification and review, starting with a statement of feasibility and concluding with a Certificate of Fitness for Service. Fluor Corporation (Fluor) has developed a new subsea cryogenic pipe-in-pipe configuration for offshore LNG loading and receiving terminals. The configuration uses a highly efficient thermal nano-porous insulation in the annular space between the inner and outer pipes. This material is kept in an ambient pressure environment, which is produced through sealing by metal bulkheads. The bulkheads transfer the contraction induced axial compression load on the inner cryogenic carrier pipe to the external jacket pipe. The resulting pipeline bundle is a structural element, which addresses the thermal contraction and expansion loads without the use of expansion bellows or ultra-low thermal contraction alloys. Fluor has followed the DNV technology qualification process to achieve the defined milestones therein which culminated in DNV issuing a certificate of fitness for service. Particular focus was put on the new aspects of the design. The certificate of fitness for service for the Fluor subsea LNG pipe technology provides project management with the confidence that this

  13. The digital divide among young people in Brussels: Social and cultural influences on ownership and use of digital technologies

    NARCIS (Netherlands)

    Mertens, S.; d'Haenens, L.S.J.

    2010-01-01

    This article reports on a survey of youth in Brussels (N = 1,005) and their ownership and use of digital technologies, focusing specifically on the social and cultural diversity within this group. Socio-cultural diversity includes differences regarding ethnicity and gender, language and educational

  14. High Performance Low Cost Digitally Controlled Power Conversion Technology

    DEFF Research Database (Denmark)

    Jakobsen, Lars Tønnes

    2008-01-01

    Digital control of switch-mode power supplies and converters has within the last decade evolved from being an academic subject to an emerging market in the power electronics industry. This development has been pushed mainly by the computer industry that is looking towards digital power management...

  15. Augmented Ontologies: The Question Concerning Digital Technology and Projectual Humanism

    NARCIS (Netherlands)

    S. Gualeni (Stefano)

    2014-01-01

    markdownabstract__Abstract__ The values of Western culture are conducive to spending a considerable amount of resources on the development of computer games, digital social networks, special effects for movies, et cetera (Bolter, 2003). With the increasingly more prominent role of digital media1 in

  16. Examining Student Digital Artifacts during a Year-Long Technology Integration Initiative

    Science.gov (United States)

    Rodriguez, Prisca M.; Frey, Chris; Dawson, Kara; Liu, Feng; Ritzhaupt, Albert D.

    2012-01-01

    This study was situated within a year-long, statewide technology integration initiative designed to support technology integration within science, technology, engineering, and math classrooms. It examined the elements used in student artifacts in an attempt to investigate trends in digital artifact creation. Among several conclusions, this…

  17. Using Digital Technologies to Improve the Authenticity of Performance Assessment for High-Stakes Purposes

    Science.gov (United States)

    Newhouse, C. Paul

    2015-01-01

    This paper reports on the outcomes of a three-year study investigating the use of digital technologies to increase the authenticity of high-stakes summative assessment in four Western Australian senior secondary courses. The study involved 82 teachers and 1015 students and a range of digital forms of assessment using computer-based exams, digital…

  18. The Contributions of Digital Communications Technology to Human Rights Education: A Case Study of Amnesty International

    Science.gov (United States)

    Norlander, Rebecca Joy

    2013-01-01

    This dissertation addresses the need for critical assessment and evaluation of human rights education (HRE) programs and activities, especially newer initiatives that incorporate the use of digital information and communications technology (ICT). It provides an in-depth case study of the use of digital ICT in Amnesty International's HRE efforts,…

  19. Digital Technology and Creative Arts Career Patterns in the UK Creative Economy

    Science.gov (United States)

    Comunian, Roberta; Faggian, Alessandra; Jewell, Sarah

    2015-01-01

    In this article, we ask what role both digital and artistic human capital play in the creative economy by examining employment patterns of digital technology (DT) and creative arts and design (CAD) graduates. Using student micro-data collected by the Higher Education Statistical Agency (HESA) in the United Kingdom, we investigate the…

  20. How Students Communicate Mathematical Ideas: An Examination of Multimodal Writing Using Digital Technologies

    Science.gov (United States)

    Freeman, Barbara; Higgins, Kristina N.; Horney, Mark

    2016-01-01

    This article reports the findings of a study designed to examine the influence of multimodal writing on the communication of mathematical ideas. Elementary school students (ages 8-13) were required to write mathematics notes using two digital writing technologies, a personal digital notepad and a social mathematics blog, in the context of a formal…

  1. Beyond the "Digital Natives" Debate: Towards a More Nuanced Understanding of Students' Technology Experiences

    Science.gov (United States)

    Bennett, S.; Maton, K.

    2010-01-01

    The idea of the "digital natives", a generation of tech-savvy young people immersed in digital technologies for which current education systems cannot cater, has gained widespread popularity on the basis of claims rather than evidence. Recent research has shown flaws in the argument that there is an identifiable generation or even a single type of…

  2. Beyond Digital Natives: European Research on Media Education; Challenges of Technology and Pedagogical Issues

    Science.gov (United States)

    Rivoltella, Pier Cesare

    2012-01-01

    This article aims to map issues of Media Education currently under debate in Europe. It points out three main research trends. The first one concerns digital natives and their skills in media and technologies. Here we have quite a dialectic situation: on the one hand, a lot of scholars and policymakers are sure that digital natives exist, that…

  3. Digital Technology and Creative Arts Career Patterns in the UK Creative Economy

    Science.gov (United States)

    Comunian, Roberta; Faggian, Alessandra; Jewell, Sarah

    2015-01-01

    In this article, we ask what role both digital and artistic human capital play in the creative economy by examining employment patterns of digital technology (DT) and creative arts and design (CAD) graduates. Using student micro-data collected by the Higher Education Statistical Agency (HESA) in the United Kingdom, we investigate the…

  4. Digi-teens: Media Literacies and Digital Technologies in the Secondary Classroom.

    Science.gov (United States)

    Burn, Andrew; Reed, Kate

    1999-01-01

    Describes a course set up for Year 11 students using digital editing equipment to examine the audiovisual fabric of films of their choice. Investigates how the advent of digital technologies enables new kinds of reading of visual texts as well as new kinds of textual production. (NH)

  5. Creativity in the Age of Technology: Measuring the Digital Creativity of Millennials

    Science.gov (United States)

    Hoffmann, Jessica; Ivcevic, Zorana; Brackett, Marc

    2016-01-01

    Digital technology and its many uses form an emerging domain of creative expression for adolescents and young adults. To date, measures of self-reported creative behavior cover more traditional forms of creativity, including visual art, music, or writing, but do not include creativity in the digital domain. This article introduces a new measure,…

  6. 78 FR 59903 - Emission Mask Requirements for Digital Technologies on 800 MHz NPSPAC Channels; Analog FM...

    Science.gov (United States)

    2013-09-30

    ... COMMISSION 47 CFR Part 90 Emission Mask Requirements for Digital Technologies on 800 MHz NPSPAC Channels; Analog FM Capability on Mutual Aid and Interoperability Channels AGENCY: Federal Communications... Petition for Rulemaking filed by Harris Corporation (Harris). The NPRM proposes to require digital...

  7. Creativity in the Age of Technology: Measuring the Digital Creativity of Millennials

    Science.gov (United States)

    Hoffmann, Jessica; Ivcevic, Zorana; Brackett, Marc

    2016-01-01

    Digital technology and its many uses form an emerging domain of creative expression for adolescents and young adults. To date, measures of self-reported creative behavior cover more traditional forms of creativity, including visual art, music, or writing, but do not include creativity in the digital domain. This article introduces a new measure,…

  8. Digital divide across borders : A cross-national study of adolescents’ use of digital technologies

    NARCIS (Netherlands)

    Notten, N.; Peter, J.; Kraaykamp, G.; Valkenburg, P.M.

    2009-01-01

    In this study, we analyse digital divides in terms of social inequality in digital access and use patterns from a hierarchical perspective. Using data from the Programme for International Student Assessment (PISA) 2003 in 30 nations, we focus on social cleavages in mid-adolescents’ access and use of

  9. Digital divide across borders: A cross-national study of adolescents use of digital technologies

    NARCIS (Netherlands)

    Notten, N.J.W.R.; Peter, J.; Kraaykamp, G.L.M.; Valkenburg, P.M.

    2009-01-01

    In this study, we analyse digital divides in terms of social inequality in digital access and use patterns from a hierarchical perspective. Using data from the Programme for International Student Assessment (PISA) 2003 in 30 nations, we focus on social cleavages in mid-adolescents access and use of

  10. After Virtual Archaeology: Rethinking Archaeological Approaches to the Adoption of Digital Technology

    Directory of Open Access Journals (Sweden)

    Gareth Beale

    2017-06-01

    Full Text Available In the 1980s archaeologists embraced the rapidly expanding field of computer modelling and visualisation as a vehicle for data exploration. Against this backdrop 'virtual archaeology' was conceived. The term was originally intended to describe a multidimensional approach to the modelling of the (immaterial structures and processes of field archaeology. It described how technology could be harnessed in order to achieve new ways of documenting, interpreting and annotating primary archaeological discoveries and processes. Despite their initial promise, these digital technologies failed to have the impact upon archaeological fieldwork that might have been expected. Even with the prevalence of digital devices on all archaeological excavations, the documentation, interpretation and subsequent narration of archaeological processes have retained their analogue character. While the archaeological record is now primarily digital, its sections, plans, drawings and photographs are facsimiles of the analogue technologies that preceded them. This retention of analogue conventions is increasingly out of step with the general prevalence and diversity of digital technologies as mediators of professional and private life. It is also challenged by 21st-century advances towards technologies that allow for complex engagements with and representations of physical matter and facilitate the interplay between digital and material worlds. This article argues that emerging forms of archaeological practice including gaming, mixed reality, computational photography and additive manufacturing, reveal digital archaeology to be a creative process, blending computational thinking, technological opportunities and established disciplinary traditions. We go on to suggest that digital archaeology, conceived as a form of practice rather than as a toolset, represents a locus for theory generation and critical thinking. Failure to recognise the skills and ideas that have emerged in

  11. 移动数字电视及其应用分析%Mobile Digital TV Technology and Application Analysis

    Institute of Scientific and Technical Information of China (English)

    牛世君

    2015-01-01

    At present,people are no longer limited to the use of fixed terminal receiving information,and grad-ually began to use mobile devices to receive information.One of the forms of new media mobile digital TV is the current information society,by virtue of its advantages continuously expand the scope of application of its own,so the research and application of mobile digital TV technology has very important practical significance. Based on this,the author first briefly overview of mobile digital TV,and then put forward the advantage of ap-plication of mobile digital TV,the final analysis of the current mobile digital TV technology.%现在人们不再局限于使用固定终端接收信息,而开始使用移动设备接收信息,其中移动数字电视就是一种全新的媒体形式,并凭借其优势不断拓展应用范围,因此探究移动数字电视技术及其应用具有重要的现实意义,基于此首先简单概述移动数字电视的社会作用,然后指出移动数字电视的技术优势,最后分析移动数字电视的应用前景。

  12. Genre, technology and embodied interaction: The evolution of digital game genres and motion gaming

    Directory of Open Access Journals (Sweden)

    Andreas Gregersen

    2011-11-01

    Full Text Available Technology has been given relatively little attention in genre theory, but this article argues that material technologies can be important components in genre development. The argument is based on a historically informed analysis of digital games, with special attention paid to home console video games and recent genre developments within this domain commonly referred to as motion gaming. The main point is that digital game genres imply structured embodied activity. A constitutive element of digital game mediation is a control interface geared to player embodiment, and I propose the concept of ‘interaction modes’ to describe the coupling of technology and player embodiment and show how this can be integrated with genre theory. The resulting framework allows for increased attention to continuity and change in game and communication genres, material and digital technologies, and the related interaction modes.

  13. AN ACTION RESEARCH IN ENGLISH LANGUAGE TEACHING AND LEARNING FOR CHILDREN WITH USE OF DIGITAL TECHNOLOGIES

    National Research Council Canada - National Science Library

    Maria Carolina Coelho Chimenti; Heloísa Andreia de Matos Lins

    2016-01-01

    The present article is based on a field research that aimed to provide educational subsidies for the use of digital technologies in teaching and learning process of English language, in two classes...

  14. Poor need knowledge not only technology to bridge digital divide: experts

    CERN Multimedia

    2003-01-01

    "Developing countries need to gain knowledge rather than technology to latch onto the booming information society, experts said Monday ahead of a major conference on bridging the digital divide between rich and poor" (1/2 page).

  15. Digital Social Media: An Interactive Technology Incorporated as a Competitive Advantage for Business

    National Research Council Canada - National Science Library

    Correia, Pedro Pereira; Medina, Irene García

    2014-01-01

    ... with socialization, the sharing of interests and the interaction with the audience. This is associated with the incorporation of digital technologies to business, specifically the use of social media...

  16. Analysis of the national scientific production on the utilization of digital technologies for nurses’ education

    Directory of Open Access Journals (Sweden)

    Viviane Rolim de Holanda

    2013-12-01

    Full Text Available The objective of this study was to seek evidence available in the national scientific literature regarding the utilization of digital teaching technologies in nurses’ education. The adopted research method was integrative literature review. The articles were selected on PubMed, LILACS, Medline, IBECS, and SciELO databases guided by the following question: what digital teaching technologies are used in nursing courses in Brazil? Eleven articles were selected. Results showed that the following were utilized: virtual learning environments, education software, interactive multimedia (CD-ROM, virtual simulations, hypertexts, digital games, websites, and virtual discussion groups (e-group/listservers. The evidence, in this study, shows that digital technologies are materials capable of optimizing knowledge acquisition complementary to traditional education, encouraging students to learning to learn. Descriptors: Education, Nursing; Teaching; Educational Technology; Nursing.

  17. Enhancement of the automatic ultrasonic signal processing system using digital technology

    Energy Technology Data Exchange (ETDEWEB)

    Koo, In Soo; Park, H. Y.; Suh, Y. S.; Kim, D. Hoon; Huh, S.; Sung, S. H.; Jang, G. S.; Ryoo, S. G.; Choi, J. H.; Kim, Y. H.; Lee, J. C.; Kim, D. Hyun; Park, H. J.; Kim, Y. C.; Lee, J. P.; Park, C. H.; Kim, M. S

    1999-12-01

    The objective of this study is to develop the automatic ultrasonic signal processing system which can be used in the inspection equipment to assess the integrity of the reactor vessel by enhancing the performance of the ultrasonic signal processing system. Main activities of this study divided into three categories such as the development of the circuits for generating ultrasonic signal and receiving the signal from the inspection equipment, the development of signal processing algorithm and H/W of the data processing system, and the development of the specification for application programs and system S/W for the analysis and evaluation computer. The results of main activities are as follows 1) the design of the ultrasonic detector and the automatic ultrasonic signal processing system by using the investigation of the state-of-the-art technology in the inside and outside of the country. 2) the development of H/W and S/W of the data processing system based on the results. Especially, the H/W of the data processing system, which have both advantages of digital and analog controls through the real-time digital signal processing, was developed using the DSP which can process the digital signal in the real-time, and was developed not only firmware of the data processing system in order for the peripherals but also the test algorithm of specimen for the calibration. The application programs and the system S/W of the analysis/evaluation computer were developed. Developed equipment was verified by the performance test. Based on developed prototype for the automatic ultrasonic signal processing system, the localization of the overall ultrasonic inspection equipment for nuclear industries would be expected through the further studies of the H/W establishment of real applications, developing the S/W specification of the analysis computer. (author)

  18. THz semiconductor-based front-end receiver technology for space applications

    Science.gov (United States)

    Mehdi, Imran; Siegel, Peter

    2004-01-01

    Advances in the design and fabrication of very low capacitance planar Schottky diodes and millimeter-wave power amplifiers, more accurate device and circuit models for commercial 3-D electromagnetic simulators, and the availability of both MEMS and high precision metal machining, have enabled RF engineers to extend traditional waveguide-based sensor and source technologies well into the TI-Iz frequency regime. This short paper will highlight recent progress in realizing THz space-qualified receiver front-ends based on room temperature semiconductor devices.

  19. THz Direct Detector and Heterodyne Receiver Arrays in Silicon Nanoscale Technologies

    Science.gov (United States)

    Grzyb, Janusz; Pfeiffer, Ullrich

    2015-10-01

    The main scope of this paper is to address various implementation aspects of THz detector arrays in the nanoscale silicon technologies operating at room temperatures. This includes the operation of single detectors, detectors operated in parallel (arrays), and arrays of detectors operated in a video-camera mode with an internal reset to support continuous-wave illumination without the need to synchronize the source with the camera (no lock-in receiver required). A systematic overview of the main advantages and limitations in using silicon technologies for THz applications is given. The on-chip antenna design challenges and co-design aspects with the active circuitry are thoroughly analyzed for broadband detector/receiver operation. A summary of the state-of-the-art arrays of broadband THz direct detectors based on two different operation principles is presented. The first is based on the non-quasistatic resistive mixing process in a MOSFET channel, whereas the other relies on the THz signal rectification by nonlinearity of the base-emitter junction in a high-speed SiGe heterojunction bipolar transistor (HBT). For the MOSFET detector arrays implemented in a 65 nm bulk CMOS technology, a state-of-the-art optical noise equivalent power (NEP) of 14 pW/ at 720 GHz was measured, whereas for the HBT detector arrays in a 0.25 μm SiGe process technology, an optical NEP of 47 pW/ at 700 GHz was found. Based on the implemented 1k-pixel CMOS camera with an average power consumption of 2.5 μW/pixel, various design aspects specific to video-mode operation are outlined and co-integration issues with the readout circuitry are analyzed. Furthermore, a single-chip 2 × 2 array of heterodyne receivers for multi-color active imaging in a 160-1000 GHz band is presented with a well-balanced NEP across the operation bandwidth ranging from 0.1 to 0.24 fW/Hz (44.1-47.8 dB single-sideband NF) and an instantaneous IF bandwidth of 10 GHz. In its present implementation, the receiver RF

  20. Digital scene simulation /SUP sm/: The synergy of computer technology and human creativity

    Energy Technology Data Exchange (ETDEWEB)

    Demos, G.; Brown, M.D.; Weinberg, R.A.

    1984-01-01

    Digital Scene Simulation is Digital Productions' philosophy for creating visual excellence in computer-generated imagery and simulation. The approach it advocates requires the use of powerful hardware, sophisticated software, and top creative talent. With a CRAY supercomputer at the heart of its computer network and its own proprietary image rendering and simulation software, Digital Productions is revolutionizing state-of-the-art computer graphics. At the forefront of computer graphics technology, Digital Productions is redefining traditional methods of visual communications and creating new forms of self-expression, instruction, and entertainment.

  1. DIGITAL TECHNOLOGY IN PRESERVATION OF BUDDIST MONASTERY TREASURES

    Directory of Open Access Journals (Sweden)

    A. Shaftel

    2017-08-01

    Full Text Available Treasure Caretaker Training (Digital Monastery Project, teaches Buddhist monks, nuns and community cultural caretakers to protect and preserve their own monastery sacred art treasures. Participants learn to create digital inventories by use of their own mobile phones. Included in this documentation is the video interview of elders who hold the oral history of many of the treasures. Risk assessment and disaster mitigation are taught.

  2. Technological characteristics of digital video broadcasting: Handheld standard DVB-H

    Directory of Open Access Journals (Sweden)

    Andreja B. Samčović

    2011-07-01

    Full Text Available This paper gives an overview of the Digital Video Broadcasting - Handheld standard DVB-H, as a part of the DVB Project. This standard is based on the previous standard DVB-T, which was developed for the terrestrial digital television. The ways of DVB-H signal transmission are also described. Development of advanced technology enabled the digital video broadcasting over wireless portable terminals. This paper discusses the key technological features of the DVB-H standard, such as: time slicing, forward error correction, 4K mode and in-depth interleavers.

  3. Using digital technologies to enhance chemistry students' understanding and representational skills

    DEFF Research Database (Denmark)

    Hilton, Annette

    and reported on two laboratory based inquiry tasks using digital technologies. Data were collected using pre- and post-tests, student texts and interviews and classroom video-recording. Content analysis of student texts indicated that students were able to generate new knowledge and use multiple...... representations to make explanations on the molecular level. Student interviews and classroom video-recordings suggested that using digital resources to create multimodal texts promoted knowledge transformation and hence deeper reflection on the meaning of data and representations. The study has implications...... for inquiry learning and using digital technologies to enhance students’ understanding of chemistry on multiple levels....

  4. [Application and prospect of digital technology in the field of orthodontics].

    Science.gov (United States)

    Zhou, Y H

    2016-06-01

    The three-dimensional(3D)digital technology has brought a revolutionary change in diagnostic planning and treatment strategy of orthodontics. Acquisition of 3D image data of the hard and soft tissues of the patients, diagnostic analysis and treatment prediction, and ultimately the individualized orthodontic appliance, will become the development trend and workflow of the 3D orthodontics. With the development of 3D digital technology, the traditional plaster model has been gradually replacing by 3D digital models. Meanwhile, 3D facial soft tissue scan and cone-beam CT scan have been gradually applied to clinical orthodontics, making it possible to get 3D virtual anatomical structure for patients. With the help of digital technology, the diagnostic process is much easier for orthodontist. However how to command the whole digital workflow and put it into practice in the daily work is still a long way to go. The purpose of this article is to enlighten the orthodontists interested in digital technology and discuss the future of digital orthodontics in China.

  5. Applying the Technology Acceptance Model in a Study of the Factors Affecting Usage of the Taiwan Digital Archives System

    Science.gov (United States)

    Hong, Jon-Chao; Hwang, Ming-Yueh; Hsu, Hsuan-Fang; Wong, Wan-Tzu; Chen, Mei-Yung

    2011-01-01

    The rapid development of information and communication technology and the popularization of the Internet have given a boost to digitization technologies. Since 2001, The National Science Council (NSC) of Taiwan has invested a large amount of funding in the National Digital Archives Program (NDAP) to develop digital content. Some studies have…

  6. Hybrid Placemaking in the Library: Designing Digital Technology to Enhance Users' On-Site Experience

    Science.gov (United States)

    Bilandzic, Mark; Johnson, Daniel

    2013-01-01

    This paper presents research findings and design strategies that illustrate how digital technology can be applied as a tool for "hybrid" placemaking in ways that would not be possible in purely digital or physical spaces. Digital technology has revolutionised the way people learn and gather new information. This trend has challenged the…

  7. Applying the Technology Acceptance Model in a Study of the Factors Affecting Usage of the Taiwan Digital Archives System

    Science.gov (United States)

    Hong, Jon-Chao; Hwang, Ming-Yueh; Hsu, Hsuan-Fang; Wong, Wan-Tzu; Chen, Mei-Yung

    2011-01-01

    The rapid development of information and communication technology and the popularization of the Internet have given a boost to digitization technologies. Since 2001, The National Science Council (NSC) of Taiwan has invested a large amount of funding in the National Digital Archives Program (NDAP) to develop digital content. Some studies have…

  8. Strengthening Inclusion of Learners With Attention Difficulties Through Interventions With Digital Technology In Processes of Production

    DEFF Research Database (Denmark)

    Sorensen, Elsebeth Korsgaard; Voldborg, Hanne

    2017-01-01

    This paper investigates the potential of digital technologies for strengthening the participation and inclusion of learners with developmental and attention deficits (focus learners) into the mainstream classroom. The paper describes the authors’ approach to the challenge of researching the extent......, to which digital technologies may support the learning process of focus learners – in particular in those aspects of the learning process that deal with the construction of learning products and the communication and dissemination of knowledge to peers, teachers or others. On the basis of the actual...... analysis and a succeeding discussion, the paper concludes that in order to create ownership, pedagogic strategies and interventions with digital technologies (whether viewed from the perspective of teaching or the perspective of learning) should incorporate opportunities for developing digital multimodal...

  9. Digital technology use by the students and english teachers and self-directed language learning

    Directory of Open Access Journals (Sweden)

    Nehir Sert

    2017-01-01

    Full Text Available The digital era is a new challenge for teachers. While children get acquainted with the digital technology before the age of six, teachers, who have encountered with the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use technology particularly beyond the classroom settings. The aim of this study was to examine the difference between the perceptions of 5-8 graders in low and high income groups about their technology use skills and their English teachers’ technology use skills. It also tested the correlation between their perceptions of their self-directed language learning behaviors and their technology use skills as well as their English teachers’ technology use skills. The population of the study consisted of 145 students. Inter group comparisons and correlational research methods were adopted. The results indicated that the low and high income students’ perceptions did not differ regarding their own technology use skills, and similarly their English teachers’ technology use skills. There was no correlation between the perceptions of the low/high income group combination regarding their technology use skills and their English teachers’ technology use skills. And lastly, their perceptions on their self-directed learning behaviors did not correlate with their perceptions on their technology use skills and their English teachers’ technology use skills. The educational implications of these results were discussed and suggestions were put forward so as to produce more effective learning environments.

  10. A Sigma-Delta ADC with Decimation and Gain Control Function for a Bluetooth Receiver in 130 nm Digital CMOS

    Directory of Open Access Journals (Sweden)

    Koh Jinseok

    2006-01-01

    Full Text Available We present a discrete-time second-order multibit sigma-delta ADC that filters and decimates by two the input data samples. At the same time it provides gain control function in its input sampling stage. A 4-tap FIR switched capacitor (SC architecture was chosen for antialiasing filtering. The decimation-by-two function is realized using divided-by-two clock signals in the antialiasing filter. Antialiasing, gain control, and sampling functions are merged in the sampling network using SC techniques. This compact architecture allows operating the preceding blocks at twice the ADC's clock frequency, thus improving the noise performance of the wireless receiver channel and relaxing settling requirements of the analog building blocks. The presented approach has been validated and incorporated in a commercial single-chip Bluetooth radio realized in a 1.5 V 130 nm digital CMOS process. The measured antialiasing filtering shows better than 75 dB suppression at the folding frequency band edge. A 67 dB dynamic range was measured with a sampling frequency of 37.5MHz.

  11. Comparison between differently priced devices for digital capture of X-ray films using computed tomography as a gold standard: a multireader-multicase receiver operating characteristic curve study.

    Science.gov (United States)

    Salazar, Antonio J; Camacho, Juan Camilo; Aguirre, Diego Andrés

    2011-05-01

    Film digitizers are a specialized technology that is available for scanning X-ray radiographs; however, their cost makes them unaffordable for developing countries. Thus, less expensive alternatives are used. The purpose of this study was to compare three devices for digital capture of X-ray films: a film digitizer (US $15,000), a flatbed scanner (US $1800), and a 10-megapixel digital camera (US $450), in terms of diagnostic accuracy, defined as the area under the receiver operating characteristic curves and computed tomography as the gold standard. The sample included 136 chest X-ray cases with computed tomography confirmation of the presence or absence of pneumothorax, interstitial opacities, or nodules. The readers were six radiologists who made observations of eight variables for each digital capture of the X-ray films: three main variables to determine the accuracy in the detection of the above-mentioned pathologies, four secondary variables to categorize other pathological classifications, and one variable regarding digital image quality. The receiver operating characteristic curves for each device and pathology were very similar. For the main variables, there was no significant statistical difference in diagnostic accuracy between the devices. For the secondary variables, >84% of cases were correctly classified, even those that were classified with the lowest image quality. High accuracy was determined for the three main variables (0.75 to 0.96), indicating good performance for all tested devices, despite their very different prices. Choosing a device for a teleradiology service should involve additional factors, such as capture time, maintenance concerns, and training requirements.

  12. Digital Libraries: The Next Generation in File System Technology.

    Science.gov (United States)

    Bowman, Mic; Camargo, Bill

    1998-01-01

    Examines file sharing within corporations that use wide-area, distributed file systems. Applications and user interactions strongly suggest that the addition of services typically associated with digital libraries (content-based file location, strongly typed objects, representation of complex relationships between documents, and extrinsic…

  13. The digital compensation technology system for automotive pressure sensor

    Science.gov (United States)

    Guo, Bin; Li, Quanling; Lu, Yi; Luo, Zai

    2011-05-01

    Piezoresistive pressure sensor be made of semiconductor silicon based on Piezoresistive phenomenon, has many characteristics. But since the temperature effect of semiconductor, the performance of silicon sensor is also changed by temperature, and the pressure sensor without temperature drift can not be produced at present. This paper briefly describe the principles of sensors, the function of pressure sensor and the various types of compensation method, design the detailed digital compensation program for automotive pressure sensor. Simulation-Digital mixed signal conditioning is used in this dissertation, adopt signal conditioning chip MAX1452. AVR singlechip ATMEGA128 and other apparatus; fulfill the design of digital pressure sensor hardware circuit and singlechip hardware circuit; simultaneously design the singlechip software; Digital pressure sensor hardware circuit is used to implementing the correction and compensation of sensor; singlechip hardware circuit is used to implementing to controll the correction and compensation of pressure sensor; singlechip software is used to implementing to fulfill compensation arithmetic. In the end, it implement to measure the output of sensor, and contrast to the data of non-compensation, the outcome indicates that the compensation precision of compensated sensor output is obviously better than non-compensation sensor, not only improving the compensation precision but also increasing the stabilization of pressure sensor.

  14. Heidegger, Digital Technology, and Postmodern Education: From Being in Cyberspace to Meeting on MySpace

    Science.gov (United States)

    Walters, Patrick; Kop, Rita

    2009-01-01

    Digital technology is transforming life and is beginning to have a profound effect on individual psychic life and the wider social milieu. This article seeks to understand the nature of the new technology and its implications for personal life, culture, and education. The scene is set by comparing the introduction of printing to the revolution…

  15. Transforming Schools with Technology: How Smart Use of Digital Tools Helps Achieve Six Key Education Goals

    Science.gov (United States)

    Zucker, Andrew A.

    2008-01-01

    In this timely and thoughtful book, Andrew Zucker argues that technology can and will play a central role in efforts to achieve crucial education goals, and that it will be an essential component of further improvement and transformation of schools. The book is marked not only by Zucker's cutting-edge sophistication about digital technologies, but…

  16. Writing Assessment and the Revolution in Digital Texts and Technologies. Language & Literacy Series

    Science.gov (United States)

    Neal, Michael

    2010-01-01

    Writing and the teaching of writing is changing at a rapid pace. How can educators understand writing assessment "as" and "with" technology in the 21st-century classroom? Michael Neal contends that new technologies are neither the problem nor the solution. Instead, educators need to tap into digital resources only inasmuch as they promote writing…

  17. Digital Teaching Platforms: Customizing Classroom Learning for Each Student. Technology & Education, Connections (TEC)

    Science.gov (United States)

    Dede, Chris, Ed.; Richards, John, Ed.

    2012-01-01

    The Digital Teaching Platform (DTP) brings the power of interactive technology to teaching and learning in classrooms. In this authoritative book, top researchers in the field of learning science and educational technology examine the current state of design and research on DTPs, the principles for evaluating them, and their likely evolution as a…

  18. Digital Libraries with Embedded Values: Combining Insights from LIS and Science and Technology Studies

    Science.gov (United States)

    Fleischmann, Kenneth R.

    2007-01-01

    In the digital age, libraries are increasingly being augmented or even replaced by information technology (IT), which is often accompanied by implicit assumptions of objectivity and neutrality, yet the field of science and technology studies (STS) has a long history of studying what values are embedded in IT and how they are embedded. This article…

  19. Young Children's Learning of Novel Digital Interfaces: How Technology Experience, Age, and Design Come into Play

    Science.gov (United States)

    Gilutz, Shuli

    2009-01-01

    This study looks at the relationship between age, technology experience, and design factors in determining young children's comprehension of novel digital interfaces. In Experiment 1, 35 preschoolers played three games that varied in complexity and familiarity. Parental questionnaires were used to assess children's previous technology experience.…

  20. Bridging the Digital Divide: Changing the Technological Landscape of Inner-City Catholic Schools

    Science.gov (United States)

    Gibbs, Michael G.; Dosen, Anthony J.; Guerrero, Rosalie B.

    2009-01-01

    This article presents an evaluation of the Bridging the Digital Divide Program, an intervention in five inner-city Chicago Catholic schools during one school year conducted by a local university. The interventions included (a) instillation of technology and (b) professional technology skill development for in-service teachers. The analysis…

  1. Digital Libraries with Embedded Values: Combining Insights from LIS and Science and Technology Studies

    Science.gov (United States)

    Fleischmann, Kenneth R.

    2007-01-01

    In the digital age, libraries are increasingly being augmented or even replaced by information technology (IT), which is often accompanied by implicit assumptions of objectivity and neutrality, yet the field of science and technology studies (STS) has a long history of studying what values are embedded in IT and how they are embedded. This article…

  2. Mathematics Education & Digital Technologies: Facing the Challenge of Networking European Research Teams

    Science.gov (United States)

    Bottino, Rosa Maria; Kynigos, Chronis

    2009-01-01

    This paper introduces the "IJCML" Special Issue dedicated to digital technologies and mathematics education and, in particular, to the work performed by the European Research Team TELMA (Technology Enhanced Learning in Mathematics). TELMA was one of the initiatives of the Kaleidoscope Network of Excellence established by the European Community…

  3. Relating Use of Digital Technology by Pre-Service Teachers to Confidence: A Singapore Survey

    Science.gov (United States)

    Yeung, Alexander Seeshing; Lim, Kam Ming; Tay, Eng Guan; Lam-Chiang, Audrey Cheausim; Hui, Chenri

    2012-01-01

    Teachers today are expected to be able to apply a wide range of digital technologies in the classroom. Initial teacher education programs should prepare teachers to apply them with confidence. Pre-service teachers in Singapore responded to a survey on use of technologies in their personal lives and in their teaching, and how confident they were in…

  4. Children Learning to Use Technologies through Play: A Digital Play Framework

    Science.gov (United States)

    Bird, Jo; Edwards, Susan

    2015-01-01

    Digital technologies are increasingly acknowledged as an important aspect of early childhood education. A significant problem for early childhood education has been how to understand the pedagogical use of technologies in a sector that values play-based learning. This paper presents a new framework to understand how children learn to use…

  5. Developing digital technologies for university mathematics by applying participatory design methods

    DEFF Research Database (Denmark)

    Triantafyllou, Eva; Timcenko, Olga

    2013-01-01

    This paper presents our research efforts to develop digital technologies for undergraduate university mathematics. We employ participatory design methods in order to involve teachers and students in the design of such technologies. The results of the first round of our design are included...

  6. The Sociology of Education and Digital Technology: Past, Present and Future

    Science.gov (United States)

    Selwyn, Neil; Facer, Keri

    2014-01-01

    During the past 15 years of his career, John Furlong's research and writing has focused--in part--on digital technologies and people's everyday experiences of education. While hardly a technology expert, his work has shown an acute awareness of the significance of computers, the internet and mobile telephony in making sociological sense…

  7. Children Learning to Use Technologies through Play: A Digital Play Framework

    Science.gov (United States)

    Bird, Jo; Edwards, Susan

    2015-01-01

    Digital technologies are increasingly acknowledged as an important aspect of early childhood education. A significant problem for early childhood education has been how to understand the pedagogical use of technologies in a sector that values play-based learning. This paper presents a new framework to understand how children learn to use…

  8. Improving Technology Competency and Disposition of Beginning Pre-Service Teachers with Digital Storytelling

    Science.gov (United States)

    Heo, Misook

    2011-01-01

    This study examined the effects of the digital storytelling experience of beginning pre-service teachers on their self-efficacy in educational technology and disposition toward change with regard to new technological approaches to teaching. A total of 76 freshmen participated in the study. After participating in a brief tutorial session, the…

  9. Leveraging New Technologies for Professional Learning in Education: Digital Literacies as Culture Shift in Professional Development

    Science.gov (United States)

    Murphy, Janet; Lebans, Robert

    2009-01-01

    Providing just-in-time job-embedded professional learning using a technologically mediated model achieves professional growth goals and encourages teachers to build digital literacy competencies and incorporate new technologies in instructional approaches in the classroom. This article highlights the lessons learned from an award-winning…

  10. Mitigation and Adaptation: Critical Perspectives toward Digital Technologies in Place-Conscious Environmental Education

    Science.gov (United States)

    Greenwood, David A.; Hougham, R. Justin

    2015-01-01

    This paper explores the tension for educators between the proliferation of mobile, digital technologies, and the widely held belief that environmental learning is best nurtured through place-based approaches that emphasize direct experience. We begin by offering a general critique of technology in culture and education, emphasizing what is at…

  11. Innovating Education and Educating for Innovation: The Power of Digital Technologies and Skills

    Science.gov (United States)

    OECD Publishing, 2016

    2016-01-01

    OECD's Innovation Strategy calls upon all sectors in the economy and society to innovate in order to foster productivity, growth and well-being. Education systems are critically important for innovation through the development of skills that nurture new ideas and technologies. However, whereas digital technologies are profoundly changing the way…

  12. The Sociology of Education and Digital Technology: Past, Present and Future

    Science.gov (United States)

    Selwyn, Neil; Facer, Keri

    2014-01-01

    During the past 15 years of his career, John Furlong's research and writing has focused--in part--on digital technologies and people's everyday experiences of education. While hardly a technology expert, his work has shown an acute awareness of the significance of computers, the internet and mobile telephony in making sociological sense…

  13. The Use of Digital Technologies in the Classroom: A Teaching and Learning Perspective

    Science.gov (United States)

    Buzzard, Christopher; Crittenden, Victoria L.; Crittenden, William F.; McCarty, Paulette

    2011-01-01

    Today's college students, often referred to as the "digital generation," use an impressive assortment of technological tools in a wide variety of ways. However, the findings reported here suggest that students prefer more traditional instructional technology for effective engagement and learning. Faculty members, however, prefer the use of…

  14. Digital Dwelling: Technology in Couple and Family Relationships

    Science.gov (United States)

    Hertlein, Katherine M.

    2012-01-01

    We are in an unprecedented age of technology. Few articles in family journals address online behavior, intimacy patterns, and influences on the ways couples and families communicate through technology. The purpose of this article is to use a multitheoretical model to describe the process of how technologies are affecting couple and family life.…

  15. Indigenous Language Revitalization, Promotion, and Education: Function of Digital Technology

    Science.gov (United States)

    Galla, Candace Kaleimamoowahinekapu

    2016-01-01

    Within the last two decades, there has been increased interest in how technology supports Indigenous language revitalization and reclamation efforts. This paper considers the effect technology has on Indigenous language learning and teaching, while conceptualizing how language educators, speakers, learners, and technology users holistically…

  16. The contributions of digital technologies in the teaching of nursing skills: an integrative review.

    Science.gov (United States)

    Silveira, Maurício de Souza; Cogo, Ana Luísa Petersen

    2017-07-13

    To analyze the contributions of digital educational technologies used in teaching nursing skills. Integrative literature review, search in five databases, from 2006 to 2015 combining the descriptors 'education, nursing', 'educational technology', 'computer-assisted instruction' or related terms in English. Sample of 30 articles grouped in the thematic categories 'technology in the simulation with manikin', 'incentive to learning' and 'teaching of nursing skills'. It was identified different formats of digital educational technologies used in teaching Nursing skills such as videos, learning management system, applications, hypertext, games, virtual reality simulators. These digital materials collaborated in the acquisition of theoretical references that subsidize the practices, enhancing the teaching and enable the use of active learning methods, breaking with the traditional teaching of demonstrating and repeating procedures.

  17. Experimental demonstration of a real-time high-throughput digital DC blocker for compensating ADC imperfections in optical fast-OFDM receivers.

    Science.gov (United States)

    Zhang, Lu; Ouyang, Xing; Shao, Xiaopeng; Zhao, Jian

    2016-06-27

    Performance degradation induced by the DC components at the output of real-time analogue-to-digital converter (ADC) is experimentally investigated for optical fast-OFDM receiver. To compensate this degradation, register transfer level (RTL) circuits for real-time digital DC blocker with 20GS/s throughput are proposed and implemented in field programmable gate array (FPGA). The performance of the proposed real-time digital DC blocker is experimentally investigated in a 15Gb/s optical fast-OFDM system with intensity modulation and direct detection over 40 km standard single-mode fibre. The results show that the fixed-point DC blocker has negligible performance penalty compared to the offline floating point one, and can overcome the error floor of the fast OFDM receiver caused by the DC components from the real-time ADC output.

  18. [Correlation of noises in the channels of digital X-ray receiver-transformer and the evaluation of registration's quant efficiency].

    Science.gov (United States)

    Porosev, V V; Shekhtman, L I; Zelikman, M I; Blinov Jr, N N

    2004-01-01

    Theoretical and experimental research results related with the influence of correlation of signals in neighboring elements of digital X-ray receiver-transformer produced on the evaluation of the output ratio noise/signal and, as a consequence, on the evaluation of quantum registration efficiency are described in the paper.

  19. Italian University Students and Digital Technologies: Some Results from a Field Research

    Science.gov (United States)

    Ferri, Paolo; Cavalli, Nicola; Costa, Elisabetta; Mangiatordi, Andrea; Mizzella, Stefano; Pozzali, Andrea; Scenini, Francesca

    Developments in information and communication technologies have raised the issue of how a kind of intergenerational digital divide can take place between "digital natives" and "digital immigrants". This can in turn have important consequences for the organization of educative systems. In this paper we present the result of a research performed during the course of 2008 to study how university students in Italy make use of digital technologies. The methodology was based on a mix of quantitative and qualitative approaches. A survey research was done, on a sample of 1186 students of the University of Milan-Bicocca, based on a questionnaire administrated through the Intranet of the University. A series of focus groups and in depth interviews with students, parents, and new media experts was furthermore performed. The results are consistent with the presence of a strong intergenerational divide. The implications of the results for the future organization of educative systems are discussed in the paper.

  20. Nagging, Noobs and New Tricks--Students' Perceptions of School as a Context for Digital Technology Use

    Science.gov (United States)

    Bulfin, Scott; Johnson, Nicola; Nemorin, Selena; Selwyn, Neil

    2016-01-01

    While digital technology is an integral feature of contemporary education, schools are often presumed to constrain and compromise students' uses of technology. This paper investigates students' experiences of school as a context for digital technology use. Drawing upon survey data from three Australian secondary schools (n = 1174), this paper…

  1. SOLUTE TRANSPORT IN NATURAL FRACTURES BASED ON DIGITAL IMAGE TECHNOLOGY

    Institute of Scientific and Technical Information of China (English)

    TAN Ye-fei; ZHOU Zhi-fang; HUANG Yong

    2009-01-01

    A method of fracture boundary extraction was developed using the Gaussian template and Canny boundary detection on the basis of the collected digital images of natural fractures. The roughness and apertures of the fractures were briefly discussed from the point of view of digital image analysis. The extracted fractured image was translated into a lattice image which can be directly used in numerical simulation. The lattice Boltzmann and modified moment propagation mixed method was then applied to the simulation of solute transport in a natural single fracture, and this mixed method could take the advantages of the lattice Boltzmann method in dealing with complex physical boundaries. The obtained concentrations was fitted with the CXTFIT2.1 code and compared with the results obtained with the commercial software Feflow. The comparison indicates that the simulation using the mixed method is sound.

  2. The Relationship of Health Literacy With Use of Digital Technology for Health Information: Implications for Public Health Practice.

    Science.gov (United States)

    Manganello, Jennifer; Gerstner, Gena; Pergolino, Kristen; Graham, Yvonne; Falisi, Angela; Strogatz, David

    An understanding of the association of health literacy with patterns related to access and usage of digital technologies and preferences for sources of health information is necessary for public health agencies and organizations to appropriately target channels for health information dissemination. A cross-sectional telephone survey was conducted in New York State. Health literacy was assessed using the Morris Single-Item Screener, a self-report question. A weighted analysis was conducted utilizing Stata/SE. The final sample size of New York State residents used for analysis was 1350. In general, self-report health literacy did not predict digital technology use (ie, Internet and smartphone use, text messaging) but was associated with certain digital activities. People with low self-report health literacy were less likely to use search engines (P = .026) but more likely to get health information from social networking sites (P = .002) and use health-related phone apps (P = .046). With respect to health information seeking, those with lower self-report health literacy reported greater difficulty with their most recent search for health information. Furthermore, they were more likely to prefer text messages (P = .013) and radio (P = .022), 2 text-limited communication channels, to receive health information than those with higher self-report health literacy. While self-report health literacy does not appear to influence access to and use of digital technologies, there is a strong association with experiences searching for health information and preferences for health information sources. Public health agencies and organizations should consider the needs and preferences of people with low health literacy when determining channels for health information dissemination. They should also consider implementing interventions to develop health information-seeking skills in populations they serve and prepare information and materials that are easily accessible and

  3. FCJ-172 Posthumanism, Technogenesis, and Digital Technologies: A Conversation with N. Katherine Hayles

    Directory of Open Access Journals (Sweden)

    Holger Pötzsch

    2014-12-01

    Full Text Available An interview with N. Katherine Hayles by Holger Pötzsch. Hayles discusses the arc of her work, from her book How We Became Posthuman to her current exploration of nonconscious cognition. She also discusses technogenesis, the digital humanities and digital technologies more generally, and more recent engagements with objects and the sciences, including the work of object oriented ontology and Karen Barad.

  4. How to integrate recent development in technology with Digital Prototype textile and apparel applications

    OpenAIRE

    2015-01-01

    The textile and clothing industry is moving away from its traditional roots in an attempt to revive the fortunes of this mature industry, through the adoption of novel technologies. Digital Prototypes are used as an essential tool in the modern design process. The integration can speed up the design process and affect competition between companies. Typical applications are digital textile and fashion design, pattern generation to custom-design clothing, fitting evaluation, style editing, and ...

  5. Digital technology shaping teaching practices in higher education

    Directory of Open Access Journals (Sweden)

    Monika eAkbar

    2016-02-01

    Full Text Available In their quest on being effective, educators have always experimented with the art of teaching. Teaching has evolved over centuries by adopting new approaches, methods, tools, and technologies to reach a wider audience. As technologies advance, educators should carefully use, evaluate, and adopt the changes to utilize the technologies and track of their impacts. This article provides a mini review to briefly describe some of the existing technical achievements that are used in higher education along with their challenges.

  6. Characterization of semiconductor-laser phase noise and estimation of bit-error rate performance with low-speed offline digital coherent receivers.

    Science.gov (United States)

    Kikuchi, Kazuro

    2012-02-27

    We develop a systematic method for characterizing semiconductor-laser phase noise, using a low-speed offline digital coherent receiver. The field spectrum, the FM-noise spectrum, and the phase-error variance measured with such a receiver can completely describe phase-noise characteristics of lasers under test. The sampling rate of the digital coherent receiver should be much higher than the phase-fluctuation speed. However, 1 GS/s is large enough for most of the single-mode semiconductor lasers. In addition to such phase-noise characterization, interpolating the taken data at 1.25 GS/s to form a data stream at 10 GS/s, we can predict the bit-error rate (BER) performance of multi-level modulated optical signals at 10 Gsymbol/s. The BER degradation due to the phase noise is well explained by the result of the phase-noise measurements.

  7. Using Web Technology to Teach Students about Their Digital World

    Science.gov (United States)

    Braender, Lynn M.; Kapp, Craig M.; Yeras, Jeddel

    2009-01-01

    In the School of Business at The College of New Jersey, students are required to take two courses in Management Information Technology (MIT). All students enroll in the same first course. This course focuses on Emerging Technologies and intermediate level data analysis skills. Students are then free to choose their second course. Each MIT course…

  8. Towards Constructions of Musical Childhoods: Diversity and Digital Technologies

    Science.gov (United States)

    Young, Susan

    2009-01-01

    The changing economic, social, cultural and technological circumstances in which children live impact significantly on the ways in which early childhood is both viewed and experienced. Understanding the implications, the potentials, the challenges that arise as a consequence of the diversity and technological changes that characterise contemporary…

  9. Towards Constructions of Musical Childhoods: Diversity and Digital Technologies

    Science.gov (United States)

    Young, Susan

    2009-01-01

    The changing economic, social, cultural and technological circumstances in which children live impact significantly on the ways in which early childhood is both viewed and experienced. Understanding the implications, the potentials, the challenges that arise as a consequence of the diversity and technological changes that characterise contemporary…

  10. New Technology's Surprising Security Threats. Building Digital Libraries

    Science.gov (United States)

    Huwe, Terence

    2005-01-01

    In recent years, security issues have increasingly come to dominate the technological development process--although still in a more reactive than proactive mode. It now seems more important than ever to monitor security trends and policy developments, especially if technology is regarded as a potential community builder. This article suggests…

  11. Digital immigrants teaching digital natives: A phenomenological study of higher education faculty perspectives on technology integration with English core content

    Science.gov (United States)

    Corey, Robert C.

    In the last two decades, technology use has escalated and educators grapple with its advances and integration into the classroom. Issues surrounding what constitutes a literate society, the clarion calls for educational reform emanating from US presidents to parent teacher organizations, and educators' ability to cope with advances in technology in the classroom demand attention. Therefore, the purpose of this qualitative study was to explore and understand the professional and educational experiences of six English faculty members teaching undergraduate courses at Midwest universities. Using the framework of Technological Pedagogical Content Knowledge -- TPACK (Koehler and Mishra 2008), the major focus of the study was to determine how faculty members understood what characterized the nature of teaching with technology in undergraduate classrooms. Results of this study revealed five themes showing how the participants were introduced to technology, how they assimilated it into their pedagogy, and how they integrated it into teaching practice. This study has the potential to impact the nature of illustrating the methods and techniques used by the six participants as they merge technology, pedagogy, and content knowledge and set in motion classroom practices that assist faculty at all levels to develop and teach technology skills necessary for the 21st century and to better prepare students for thinking critically about how to use digital advances.

  12. Science Notebooks for the 21st Century. Going Digital Provides Opportunities to Learn "with" Technology Rather than "from" Technology

    Science.gov (United States)

    Fulton, Lori; Paek, Seungoh; Taoka, Mari

    2017-01-01

    Students of today are digital natives who for the most part come to school with experiences that may surpass those of their teachers. They use tablet computers and other devices in their personal lives and are eager to use them in the classroom. For teachers, this means they must integrate technology in ways that allow their students to learn with…

  13. Population health-based approaches to utilizing digital technology: a strategy for equity.

    Science.gov (United States)

    Graham, Garth N; Ostrowski, MaryLynn; Sabina, Alyse B

    2016-11-01

    Health care disparities and high chronic disease rates burden many communities and disproportionally impact racial/ethnic populations in the United States. These disparities vary geographically, increase health care expenses, and result in shortened lifespans. Digital technologies may be one tool for addressing health disparities and improving population health by increasing individuals' access to health information-especially as most low-income U.S. residents gain access to smartphones. The Aetna Foundation partners with organizations to use digital technologies, including mobile applications, data collection, and related platforms, for learning and sharing. Projects range from the broad-childhood education, lifestyle modification, health IT training, and nutrition education, to the specific-local healthy foods, stroke rehabilitation, and collection of city-level data. We describe our approaches to grantmaking and discuss lessons learned and their implications. When combined with sound policy strategies, emerging, scalable, digital technologies will likely become powerful allies for improving health and reducing health disparities.

  14. Facilitating continuity: exploring the role of digital technology in physical rehabilitation

    DEFF Research Database (Denmark)

    Bagalkot, Naveen L.; Nazzi, Elena; Sokoler, Tomas

    2010-01-01

    In this paper we report our early experiences on exploring if, and how, digital technology can help facilitate a stronger sense of continuity in the physical rehabilitation process, as experienced by the therapists and the senior citizens. We recognize four aspects of the design space offered...... for the physical rehabilitation of senior citizens. Secondly, and more importantly, we provide a pointer towards a new practice of physical rehabilitation: a practice where the role of digital technology is to support, through the facilitation of continuity, the collaboration between therapist and senior citizens......-through-design approach we have used sketching in a co-design setting with senior citizens and therapists, as the main vehicle for our research. With our MagicMirror and Walky design explorations, we aim to contribute on two levels: firstly, by providing two proof-of-concepts of designing digital technology...

  15. Application of digital pattern-less molding technology to produce art casting

    Directory of Open Access Journals (Sweden)

    Chen Li1

    2014-11-01

    Full Text Available Compared with the conventional casting process, digital pattern-less casting technology has many advantages such as good machining accuracy, a short processing cycle, and low production cost. It is a new rapid manufacturing technology for castings, integrated with CAD/CAM, casting, CNC machining and many other advanced technologies. With this digital casting technology, no pattern is needed for making molds; it is precise, flexible, and green. Usually, art castings have complex structures and are made in small batches or even made in a single-piece, especially for large-sized art castings. So it has the shortcomings of high cost, low efficiency and long time for making a pattern to produce art castings with the conventional casting processes. However, the digital pattern-less casting technology can be applied to fabricate art castings, since it can greatly shorten the manufacturing cycle and lower the production cost, thus having a very good prospect. In this study, based on the digital pattern-less casting technology, a plaque casting with artistic Chinese characters (a Chinese poem was designed and manufactured, and the production process was demonstrated in detail.

  16. A Digital Archives Framework for the Preservation of Cultural Artifacts with Technological Components

    Directory of Open Access Journals (Sweden)

    Guillaume Boutard

    2013-06-01

    Full Text Available The preservation of artistic works with technological components, such as musical works, is recognised as an issue by both the artistic community and the archival community. Preserving such works involves tackling the difficulties associated with digital information in general, but also raises its own specific problems, such as constantly evolving digital instruments embodied within software and idiosyncratic human-computer interactions. Because of these issues, standards in place for archiving digital information are not always suitable for the preservation of these works. The impact on the organisation and the descriptions of such archives need to be conceptualised in order to provide these technological components with readability, authenticity and intelligibility. While previous projects emphasized readability and authenticity, less effort has been dedicated to addressing intelligibility issues.The research into the specification of significant properties and its extension, namely significant knowledge, offers some grounds for reflecting on this question. Furthermore, the relevance of taking into account the creative process involved in the production of technological components offers an opportunity to redefine the status of technological agents in the performative aspect of digital records. Altogether, the research on significant knowledge and creative processes provide us with a conceptual framework that we propose to bring together with digital archives models to form a coherent framework.

  17. Digital innovations and emerging technologies for enhanced recovery programmes

    DEFF Research Database (Denmark)

    Michard, F; Gan, T J; Kehlet, H

    2017-01-01

    monitoring techniques and decision support tools are now available to individualize perioperative fluid management, a key component of ERPs. Objective nociceptive assessment may help to rationalize the use of pain medications, including opioids. Wearable sensors designed to monitor cardio...... of the above-mentioned ERP elements is omitted during the surgical journey.By optimizing compliance to the multiple components of ERPs, digital innovations, non-invasive techniques and wearable sensors have the potential to magnify the clinical and economic benefits of ERPs. Among the growing number...

  18. Gains from resistance: contesting a new digital technology in a service sector workplace

    DEFF Research Database (Denmark)

    Shulzhenko, Elena; Holmgren, Jens

    2017-01-01

    Increasing expectations of efficiency enabled by new digital technology have led to renewed interest in spaces remaining for employee resistance to management power. The study contributes to this debate by analysing resistance to a new technology introduced in the home-nursing sector in Denmark....... Nurses succeeded in halting a technological change that allowed them to report data related to their visits online from inside patients’ homes and reduced their co-located working time. Work location became a central area of contestation between nurses and management. The study offers a nuanced analysis...... of power relations during the technological change. It shows that the capacity of IT management – a management actor uninhibited by a care ethos - to influence nursing workplaces rose along with the increasing significance of expertise in digital technologies in performing care work. Nurses’ alliances...

  19. Preferences of Young Adults With First-Episode Psychosis for Receiving Specialized Mental Health Services Using Technology: A Survey Study

    OpenAIRE

    2015-01-01

    Background Despite the potential and interest of using technology for delivering specialized psychiatric services to young adults, surprisingly limited attention has been paid to systematically assess their perspectives in this regard. For example, limited knowledge exists on the extent to which young people receiving specialized services for a first-episode psychosis (FEP) are receptive to using new technologies as part of mental health care, and to which types of technology-enabled mental h...

  20. Review of innovations in digital health technology to promote weight control.

    Science.gov (United States)

    Thomas, J Graham; Bond, Dale S

    2014-01-01

    Advances in technology have contributed to the obesity epidemic and worsened health by reducing opportunities for physical activity and by the proliferation of inexpensive calorie-dense foods. However, much of the same technology can be used to counter these troublesome trends by fostering the development and maintenance of healthy eating and physical activity habits. In contrast to intensive face-to-face treatments, technology-based interventions also have the potential to reach large numbers of individuals at low cost. The purpose of this review is to discuss studies in which digital technology has been used for behavioral weight control, report on advances in consumer technology that are widely adopted but insufficiently tested, and explore potential future directions for both. Web-based, mobile (eg, smartphone), virtual reality, and gaming technologies are the focus of discussion. The best evidence exists to support the use of digital technology for self-monitoring of weight-related behaviors and outcomes. However, studies are underway that will provide additional, important information regarding how best to apply digital technology for behavioral weight control.

  1. Wideband CMOS receivers

    CERN Document Server

    Oliveira, Luis

    2015-01-01

    This book demonstrates how to design a wideband receiver operating in current mode, in which the noise and non-linearity are reduced, implemented in a low cost single chip, using standard CMOS technology.  The authors present a solution to remove the transimpedance amplifier (TIA) block and connect directly the mixer’s output to a passive second-order continuous-time Σ∆ analog to digital converter (ADC), which operates in current-mode. These techniques enable the reduction of area, power consumption, and cost in modern CMOS receivers.

  2. Assessment of the usability of a digital learning technology prototype for monitoring intracranial pressure

    Directory of Open Access Journals (Sweden)

    Lilian Regina de Carvalho

    Full Text Available ABSTRACT Objective: to assess the usability of a digital learning technology prototype as a new method for minimally invasive monitoring of intracranial pressure. Method: descriptive study using a quantitative approach on assessing the usability of a prototype based on Nielsen's ten heuristics. Four experts in the area of Human-Computer interaction participated in the study. Results: the evaluation delivered eight violated heuristics and 31 usability problems in the 32 screens of the prototype. Conclusion: the suggestions of the evaluators were critical for developing an intuitive, user-friendly interface and will be included in the final version of the digital learning technology.

  3. Development of the Licensing Support Technology for Digital I and C

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, K. C.; Kim, J. Y.; Kang, H. K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

    2008-06-15

    This research can provide the required safety and reliability of software for the use of nuclear digital safety systems, achieve the software quality sufficient to arrive at the level of the licensing agreement by the nuclear regulatory agency, and establish the rigorous software V and V procedure by the use of domestic technology. These results will provide independent safety software qualification techniques from, with the equivalent level of, the those acquired by advanced countries. The technologies obtained from this research will be able to be employed at advanced reactors such as super-critical fast reactors, high temperature gas-cooled reactors, and small modularized reactors that promote the use of digital systems.

  4. Montecarlo Simulation Applied to Measurement of the Impact of the Smart Antenna Technology in Digital Cellular Systems

    Directory of Open Access Journals (Sweden)

    Castañeda-Camacho Josefina

    2015-03-01

    Full Text Available The smart antenna technology has received increasing interest due to its capability for improving the performance of wireless radio systems. In this work, we studied the throughput maximization in a digital cellular system when a smart antenna array is implemented. We focus, in the study of the downlink of a 3G cellular system and consider a packet data direct-sequence code division, multiple access (DS-CDMA. Our methodology is based on the Monte Carlo simulation technique, and it is used to show that it is possible to obtain a significant increment in the throughput of the system due to the switched beam smart antenna array. From our results we conclude that it is feasible to consider the application of this technology in 4G environments.

  5. Design of the Digital Channelized Receiver Based On Multi-phase Filter%基于多相滤波的数字信道化接收机的设计

    Institute of Scientific and Technical Information of China (English)

    李宏强; 张洪波

    2014-01-01

    According to the characteristic of the digital channelized receiver, which must have the ability of processing the large number of data in real time, an efficient digital parallel analyzing system is introduced in this paper, and it adopts the multi-phase filter technology to implement channelization. The method resolves the contradiction between the high-speed ADC and low-speed digital signal processor (FPGA). The working processing of the whole receiver is described from mathematics model, and the system is simulated in MATLAB environment. The correctness and the validity of the algorithm model are proved by the simulation results.%介绍的基于多相结构的数字信道化技术具有实时处理大量数据能力的特点,是克服高速ADC与FPGA处理速度之间的矛盾的关键技术。从数学模型上描述了整个接收机的工作流程,并在MATLAB环境中对系统进行了仿真,仿真结果验证了该算法模型的正确性与高效性。

  6. SEMICONDUCTOR INTEGRATED CIRCUITS: A reconfigurable OTA-C baseband filter with wide digital tuning for GNSS receivers

    Science.gov (United States)

    Wenguang, Pan; Chengyan, Ma; Yebing, Gan; Tianchun, Ye

    2010-09-01

    The design of a digitally-tunable sixth-order reconfigurable OTA-C filter in a 0.18-μm RFCMOS process is proposed. The filter can be configured as a complex band pass filter or two real low pass filters. An improved digital automatic frequency tuning scheme based on the voltage controlled oscillator technique is adopted to compensate for process variations. An extended tuning range (above 8:1) is obtained by using widely continuously tunable transcon-ductors based on digital techniques. In the complex band pass mode, the bandwidth can be tuned from 3 to 24 MHz and the center frequency from 3 to 16 MHz.

  7. Digitization

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2014-01-01

    Processes of digitization have for years represented a major trend in the developments of modern society but have only recently been related to processes of mediatization. The purpose of this article is to look into the relation between the concepts of mediatization and digitization and to clarify...... what a concept of digital media might add to the understanding of processes of mediatization and what the concept of mediatization might add to the understanding of digital media. It is argued that digital media open an array of new trajectories in human communication, trajectories which were...... not anticipated in previous conceptualizations of media and mediatization. If digital media are to be included, the concept of mediatization has to be revised and new parameters are to be built into the concept of media. At the same time it is argued that the concept of mediatization still provides a variety...

  8. Digital Photography and Journals in a Kindergarten-First-Grade Classroom: Toward Meaningful Technology Integration in Early Childhood Education

    Science.gov (United States)

    Ching, Cynthia Carter; Wang, X. Christine; Shih, Mei-Li; Kedem, Yore

    2006-01-01

    To explore meaningful and effective technology integration in early childhood education, we investigated how kindergarten-first-grade students created and employed digital photography journals to support social and cognitive reflection. These students used a digital camera to document their daily school activities and created digital photo…

  9. The role of digital health technologies in management of pain in older people: An integrative review.

    Science.gov (United States)

    Bhattarai, Priyanka; Phillips, Jane L

    Pain is one of the most distressing and debilitating health issues faced by older people. The burden of unrelieved pain experienced by older people and its associated high symptom and economic costs demands consideration of new strategies to better this condition. As the global uptake of digital technology increases, exploring its potential to impact positively on older peoples' pain self-management practices warrants investigation. This integrative review aimed to evaluate the use of digital health technology for management of older people's pain across care-settings. Searches were conducted to identify relevant English language studies published in CINHAL, Medline, Academic Search Complete, EMBASE, Cochrane library databases, and Google and Google Scholar websites. A total of 1003 papers were identified, 9 met the inclusion criteria. The highest level of evidence (Level II) was generated by three Phase II randomized controlled trials. These trials demonstrated the feasibility of computer based interactive or instructive video interventions however there was limited evidence to support their use for reduction of pain intensity and interference. Qualitative evidence demonstrated older people's willingness to use mobile technologies (iPhone or digital pen) to help manage their pain, however, the need of device-use training and connectedness with clinicians were highlighted. In conclusion, there is some evidence that integrating digital health technology into older peoples' pain self-management plan is feasible and acceptable. However, the provision of high-quality technological interventions informed by a thorough understanding of older people's digital technology pain management needs is required to ensure greater integration of this technology in clinical practice. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  10. Research and implementation of the key technology of digital lock-in amplifier

    Science.gov (United States)

    Liu, Wei; You, Jia; Feng, Cheng; Li, Xisheng

    2017-08-01

    Lock-in amplifier technology is a very effective means of weak signal detection, with a center frequency stability, narrow pass band, high quality factor, which has been widely applied in physics, chemistry, biomedicine, remote sensing, materials science, etc. With the development of digital signal processing technology, digital phase-locked amplifier gradually replace analog lock-in amplifier, phase sensitive detector improved analog lock-in amplifier using analog method, by the way of the digital signal processing to achieve phase sensitive detector. FPGA has strong flexibility, can be programmed, and debugged, can be fully developed and verified. In this paper, we complete the construction of the digital lock-in amplifier based on the FPGA platform, using DSP Builder as design tool, using the ALTER's IP core to achieve rapid implementation. It is mainly divided into three modules: numerically controlled oscillator, Fast Fourier Transformation, digital phase sensitive detector. According to the process of MATLAB/Simulink/DSP Builder/Quartus II, it calls fft_v13_0 core, nco_v13_0 core provided by DSP Builder toolbox to build the model. The experimental results show that the designed digital phase-locked amplifier can effectively remove the noise interference and improve the detection accuracy.

  11. Report on Disclosure Issues Related to the Use of Copy Control and Digital Rights Management Technologies. OECD Digital Economy Papers, No. 115

    Science.gov (United States)

    OECD Publishing (NJ1), 2006

    2006-01-01

    This report analyses the disclosure issues raised by technically-imposed restrictions on the use of digital content. It focuses on the application of copy control and digital rights management technologies in three areas: copy-protected CDs; online music, and DVD regional coding. In each of these areas, the report examines the kinds of…

  12. Experimental demonstration of a format-flexible single-carrier coherent receiver using data-aided digital signal processing.

    Science.gov (United States)

    Elschner, Robert; Frey, Felix; Meuer, Christian; Fischer, Johannes Karl; Alreesh, Saleem; Schmidt-Langhorst, Carsten; Molle, Lutz; Tanimura, Takahito; Schubert, Colja

    2012-12-17

    We experimentally demonstrate the use of data-aided digital signal processing for format-flexible coherent reception of different 28-GBd PDM and 4D modulated signals in WDM transmission experiments over up to 7680 km SSMF by using the same resource-efficient digital signal processing algorithms for the equalization of all formats. Stable and regular performance in the nonlinear transmission regime is confirmed.

  13. Technology to support a distributed digital library for astronomy

    Science.gov (United States)

    Biemesderfer, C. D.

    1996-12-01

    The integrated electronic resource that is forming in the astronomical community is a functional distributed digital library. As the balance of the literature comes on-line over the next year, and as more organizations seek to make data and other resources available on the Internet, ad hoc agreements among groups will give way to de facto standards. In our effort to extend the knowledge gained in our work on the electronic ApJ, we are engaged in an initiative to collaborate with other publishers and information distributors to utilize existing tools so that disparate collections may interoperate. We expect to devise effective operating conventions, and to articulate standard means for making valuable, archival information accessible on the net, reliably and for the long term.

  14. Toward high-performance digital logic technology with carbon nanotubes.

    Science.gov (United States)

    Tulevski, George S; Franklin, Aaron D; Frank, David; Lobez, Jose M; Cao, Qing; Park, Hongsik; Afzali, Ali; Han, Shu-Jen; Hannon, James B; Haensch, Wilfried

    2014-09-23

    The slow-down in traditional silicon complementary metal-oxide-semiconductor (CMOS) scaling (Moore's law) has created an opportunity for a disruptive innovation to bring the semiconductor industry into a postsilicon era. Due to their ultrathin body and ballistic transport, carbon nanotubes (CNTs) have the intrinsic transport and scaling properties to usher in this new era. The remaining challenges are largely materials-related and include obtaining purity levels suitable for logic technology, placement of CNTs at very tight (∼5 nm) pitch to allow for density scaling and source/drain contact scaling. This review examines the potential performance advantages of a CNT-based computing technology, outlines the remaining challenges, and describes the recent progress on these fronts. Although overcoming these issues will be challenging and will require a large, sustained effort from both industry and academia, the recent progress in the field is a cause for optimism that these materials can have an impact on future technologies.

  15. Digital Watermark-based Security Technology for Geo-spatial Graphics Data

    Institute of Scientific and Technical Information of China (English)

    JIA Peihong; CHEN Yunzhen; MA Jinsong; ZHU Dakui

    2006-01-01

    The paper presents a set of techniques of digital watermarking by which copyright and user rights messages are hidden into geo-spatial graphics data, as well as techniques of compressing and encrypting the watermarked geo-spatial graphics data. The technology aims at tracing and resisting the illegal distribution and duplication of the geo-spatial graphics data product, so as to effectively protect the data producer's rights as well as to facilitate the secure sharing of geo-spatial graphics data. So far in the GIS field throughout the world, few researches have been made on digital watermarking. The research is a novel exploration both in the field of security management of geo-spatial graphics data and in the applications of digital watermarking technique. An application software employing the proposed technology has been developed. A number of experimental tests on the 1:500,000 digital bathymetric chart of the South China Sea and 1:10,000 digital topographic map of Jiangsu Province have been conducted to verify the feasibility of the proposed technology.

  16. Investigation of Virtual Digital Human and Robotic Device Technology Merger Complimented by Haptics and Autostereoscopic Displays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovations conform precisely to the technology needs described in Subtopic T5.02, Robotics and Virtual Digital Human Technologies. ?Two potential areas...

  17. Object-Based Teaching and Learning for a Critical Assessment of Digital Technologies in Arts and Cultural Heritage

    Science.gov (United States)

    Hess, M.; Garside, D.; Nelson, T.; Robson, S.; Weyrich, T.

    2017-08-01

    As cultural sector practice becomes increasingly dependent on digital technologies for the production, display, and dissemination of art and material heritage, it is important that those working in the sector understand the basic scientific principles underpinning these technologies and the social, political and economic implications of exploiting them. The understanding of issues in cultural heritage preservation and digital heritage begins in the education of the future stakeholders and the innovative integration of technologies into the curriculum. This paper gives an example of digital technology skills embedded into a module in the interdisciplinary UCL Bachelor of Arts and Sciences, named "Technologies in Arts and Cultural Heritage", at University College London.

  18. Testing of the small sample (new concept) calorimeter received from EG&G Mound Applied Technology

    Energy Technology Data Exchange (ETDEWEB)

    Cech, R.; Craft, M.; Fultz, R. [and others

    1998-12-31

    The Small Sample calorimeter, also known as the New Concepts calorimeter, has undergone testing in the transfer of the calorimeter operations to Los Alamos National Laboratory from EG&G Mound Applied Technology (Mound), Miamisburg, Ohio, in September 1996. The design of the calorimeter incorporated several new concepts, thus the name New Concepts. The normal water bath was replaced with a small self-contained bath and control that used a thermal electric cooling/heating device to supply the control for the bath temperature. This change replaces the large refrigeration unit that has been used in the past, thus reducing the weight and the power required to operate the system. The design was done to allow the complete calorimeter system to be contained in a single electronics rack. With the new electronics package, this change would allow the unit to use a short electronics rack with a laptop computer and make the complete system transportable. By reducing the amount of water in the bath, the control and size of the bath could also be reduced. By making the bath self-contained and sealed, there would be no need to replace water or supply de-ionized water for the system. This change would remove some of the concerns about using a water bath in certain situations. The water would be about 5 gal. or less depending on the size of the calorimeter. The present system is a 5 in. diameter sample chamber system which can accept most older material now in storage. It will not handle the new 3013 size container as built but could be easily designed for that size. There is also a new sensor design that takes less wire and can eliminate the constant current source used in past Mound calorimeter designs. With the new digital voltmeters, the complete system could be run from a single meter with the ability to monitor bath and room as well as the calorimeter operating voltages for electrical heater runs. A few problems, though minor, need to be corrected to make the system available.

  19. Trends in the use of digital technology for control and regulation of power supplies.

    Energy Technology Data Exchange (ETDEWEB)

    Carwardine, J.; Lenkszus, F.

    1999-10-22

    Since the availability of computers, accelerator power supplies have relied on digital technology in some way, from such simple tasks as turning the supplies on and off to the supplying of computer-controlled references. However, advances in digital technology, both in performance and cost, allow considerably more than simple control and monitoring. This, coupled with increasing demand for higher performance and monitoring capabilities, has made it appealing to integrate such technology into power supply designs. This paper will review current trends in the use of such advanced technology as embedded DSP controllers, and the application of real-time algorithms to the regulation and control of power supplies for accelerators and other large-scale physics applications.

  20. An Investigation of Middle School Science Teachers and Students Use of Technology inside and outside of Classrooms: Considering Whether Digital Natives Are More Technology Savvy than Their Teachers

    Science.gov (United States)

    Wang, Shiang-Kwei; Hsu, Hui-Yin; Campbell, Todd; Coster, Daniel C.; Longhurst, Max

    2014-01-01

    The purpose of the study is to investigate the popular assumption that the "digital natives" generation surpasses the previous "digital immigrants" generation in terms of their technology experiences, because they grow up with information and communication technology. The assumption presumes that teachers, the digital…

  1. Digital technology use in ELT classrooms and self-directed learning

    Directory of Open Access Journals (Sweden)

    Nehir Sert

    2016-04-01

    Full Text Available The digital era is a new challenge for teachers. While children get acquainted with digital technology before the age of six, teachers, who have encountered the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use of technology within and beyond classroom settings. The aim of this study was to examine the difference between the perceptions of students in low- and high-income groups about their use of technology in a general sense and their teachers’ use of technology in ELT classrooms. It also tested the correlation between the perceptions of their self-directed learning behaviours and their own/their teachers’ technology use. The population of the study consisted of 75 students from high- and 70 students from low-income groups. Causal comparative and correlational research methods were adopted in the study. The surveys to measure the students’ perceptions about technology use were developed by the researchers. A scale, established by Demirtas and Sert (2010, was used to identify the level of self-directed learning views of the students. The data were collected at the beginning of the first term of the 2015-2016 school year. The results indicated that there was no significant difference between perceptions of the low- and high-income students regarding their own technology use. Likewise, perceptions of the low- and high-income students did not differ regarding their teachers’ technology use. There was no correlation between the perceptions of the low-/high-income mixed group regarding their use of technology and their teachers’ use of technology. Lastly, self-directed learning perceptions of the low-/high-income mixed group did not correlate with their perceptions on any aspects of technology use. The educational implications of these results were discussed and suggestions were put forward in order to produce more effective learning

  2. Dentist-technician collaboration in the digital age: enhancing outcomes through photography, teamwork, and technology.

    Science.gov (United States)

    Schoenbaum, Todd R; Chang, Yi-Yuan

    2011-08-01

    The cornerstone of a strong and successful dentist-technician relationship is communication. High-level collaboration across distances requires modern technology to communicate expectations, potential outcomes, and limitations. Carefully calibrated digital photography is an essential element in this inherently artistic process. This ensures a system of checks and balances to minimize the potential for miscommunication and remakes. Forthcoming technologies will allow dentist-technician teams to reach ever-greater levels of collaboration.

  3. Human factors multi-technique approach to teenage engagement in digital technologies health research

    OpenAIRE

    Lang, Alexandra R; Craven, Michael P; Atkinson, Sarah; Simons, Lucy; Cobb, Sue; Mazzola, Marco

    2016-01-01

    This chapter explores the use of multi-techniques for teenage HCI health research. Through four case studies we present information about adolescents as users of healthcare services and technologies, adolescent personal development and the human factors approaches through which teenagers have been involved in healthcare research projects. In each case study; comprising of the design or evaluation of a new digital technology for supporting health or well-being, the techniques used by researche...

  4. Effect of Information and Communication Technologies (ICT) on Non-Industrial Countries-Digital Divide Model

    OpenAIRE

    MAHMOUD Z. ISKANDARANI

    2008-01-01

    The influence of information and communication technology on the collective activities and interests of a broad range of people was discussed and analyzed. The important consequence of ICT called digital divide was mathematically modeled and the results analyzed. The closed loop feedback model proved the need for a society to be educationally, culturally, economically and politically ready to integrate and implement new technologies into its infrastructure.

  5. Information and communication technologies in tomorrow's digital classroom

    Science.gov (United States)

    Bogoeva, Asya

    2014-05-01

    Education has to respond to the new challenges and opportunities offered by the 21-th Century as well as to the main trend in the world community development related to a creation of Knowledge Society. Implementation of ICT at school is a priority of the Global education and helps to develop the four pillars of learning - learning to know, learning to do, learning to be and learning to live together. Digital competence of the students is also a part of the European Union key competences. The essential elements in geographical study are: spatial analysis, with an emphasis on location; ecological analysis, with an emphasis on people-environment relationships; and regional analysis, with an emphasis on areal differentiation. Modern geography is best characterized as the study of distributions and relationships among different natural and social patterns of distributions. Viewing the world from a spatial perspective and employing a holistic approach are important characteristics of contemporary and future Geography learning. Using innovative methods for presenting the global aspects of distribution patterns and their changes is a priority of teaching geosciences at our school. The use of geo-media in classroom helps learners develop their ICT competences. Geolocalised information is used everywhere in society and it is therefore essential for students to learn how to use different forms of geographic media Geo-media is now being used in scientific researches and reasoning. One of the geo-media tools that I use in my classes is Google Earth for presenting different geographic processes and phenomena like visualization of current global weather conditions, global warming, deforestation areas, earthquake areas, etc. Using Geographic Information systems for presenting and studying geographical processes is also one way to identify, analyze, and understand the locations. Our school is a part of digital-earth.eu network which is under development now. The European Centers of

  6. Mobile Technology for Community Health in Ghana: what happens when technical functionality threatens the effectiveness of digital health programs?

    Science.gov (United States)

    LeFevre, Amnesty E; Mohan, Diwakar; Hutchful, David; Jennings, Larissa; Mehl, Garrett; Labrique, Alain; Romano, Karen; Moorthy, Anitha

    2017-03-14

    Despite the growing use of technology in the health sector, little evidence is available on the technological performance of mobile health programs nor on the willingness of target users to utilize these technologies as intended (behavioral performance). In this case study of the Mobile Technology for Health (MOTECH) program in Ghana, we assess the platform's effectiveness in delivering messages, along with user response across sites in five districts from 2011 to 2014. MOTECH is comprised of "Client Data Application" (CDA) which allows providers to digitize and track service delivery information for women and infants and "Mobile Midwife" (MM) which sends automated educational voice messages to the mobile phones of pregnant and postpartum women. Using a naturalist study design, we draw upon system generated data to evaluate message delivery, client engagement, and provider responsiveness to MOTECH over time and by level of facility. A total of 7,370 women were enrolled in MM during pregnancy and 14,867 women were enrolled postpa1rtum. While providers were able to register and upload patient-level health information using CDA, the majority of these uploads occurred in Community-based facilities versus Health Centers. For MM, 25% or less of expected messages were received by pregnant women, despite the majority (>77%) owning a private mobile phone. While over 80% of messages received by pregnant women were listened to, postpartum rates of listening declined over time. Only 25% of pregnant women received and listened to at least 1 first trimester message. By 6-12 months postpartum, less than 6% of enrolled women were exposed to at least one message. Caution should be exercised in assuming that digital health programs perform as intended. Evaluations should measure the technological, behavioral, health systems, and/or community factors which may lead to breaks in the impact pathway and influence findings on effectiveness. The MOTECH platform's technological limitations

  7. Digital Technologies and the Mediation of Undergraduate Students' Collaborative Music Compositional Practices

    Science.gov (United States)

    Dobson, Elizabeth; Littleton, Karen

    2016-01-01

    Music education is supported by an increasing range of digital technologies that afford a remarkable divergence of opportunities for learning within the classroom. Musical creativities are not, however, limited to classroom situations; all musicians are engaged in work that traverses multiple social and physical settings. Guided by sociocultural…

  8. Between Assessments, Digital Technologies and Big Data: The Growing Influence of "Hidden" Data Mediators in Education

    Science.gov (United States)

    Hartong, Sigrid

    2016-01-01

    The past few decades have witnessed a global enforcement of "governance by data" in education policy, including a significant increase of assessments and quantified evaluation. Within this context, this article focuses particularly on the intensifying evolvement of new (digital) information technologies and "mediated"…

  9. The use of modern technology in education: A user study on the digitization of cultural heritage

    Directory of Open Access Journals (Sweden)

    MILICA LAJBENŠPERGER

    2013-09-01

    Full Text Available In the Republic of Serbia the idea that the digitization of cultural heritage could be used to popularize and utilize modern technologies in education was first realized in 2012. One of the results of this project was a user study. In this paper we indicate some of project’s fragments and present some of the results of the conducted research.

  10. Digital technology and mid-adopting teachers’ professional development : a case study

    NARCIS (Netherlands)

    Drijvers, Paul; Tacoma, Sietske; Besamusca, A.; Heuvel, C. van den; Doorman, Michiel; Boon, Peter

    2014-01-01

    The integration of digital technology into secondary mathematics education is not yet a widespread success. As teachers are crucial players in this integration, an important challenge is not only to attract early adopters, but also to support mid-adopting teachers in their professional development o

  11. Investigating How Digital Technologies Can Support a Triad-Approach for Student Assessment in Higher Education

    Science.gov (United States)

    Vaughan, Norman

    2013-01-01

    The purpose of this research study was to investigate if and how digital technologies could be used to support a triad-approach for student assessment in higher education. This triad-approach consisted of self-reflection, peer feedback, and instructor assessment practices in a pre-service teacher education course at a Canadian university. Through…

  12. Implementing Digital Storytelling as a Technology Integration Approach with Primary School Children

    Directory of Open Access Journals (Sweden)

    Nuala Sweeney-Burt

    2014-06-01

    Full Text Available Irish educational policy acknowledges the importance of integrating technology meaningfully into teaching and learning at the primary level. Much remains to be done, however, in terms of developing, practically implementing and evaluating the use of technology in the Irish primary classroom. This paper describes a study on the use of a structured approach to digital storytelling as a tool for meaningful technology integration with children at primary level. In this study, the researcher developed a structured approach for implementing digital storytelling with primary school children, and collaborated with a class teacher in an Irish primary school to prepare to implement the approach. Multiple qualitative methods were used to evaluate the implementation, including interviews with the teacher, classroom observation, and focus group interviews with participating children. The results suggested that this structured approach to digital storytelling has the potential to be used successfully as a meaningful technology integration approach with this cohort. The findings also explored implications for the implementation of digital storytelling at primary level, and identified aspects on which further research should be undertaken to enhance and extend the approach that was used.

  13. Facilitating English-Language Learners' Oral Reading Fluency with Digital Pen Technology

    Science.gov (United States)

    Chen, Chih-Ming; Tan, Chia-Chen; Lo, Bey-Jane

    2016-01-01

    Oral reading fluency is an indicator of overall reading competence. Many studies have claimed that repeated reading can promote oral reading fluency. Currently, novel Web- or computer-based reading technologies offer interactive digital materials that promote English oral reading fluency using the repeated reading strategy; however, paper-based…

  14. Student Teachers' Discourse about Digital Technologies and Transitions between Formal and Informal Learning Contexts

    Science.gov (United States)

    Pöntinen, Susanna; Dillon, Patrick; Väisänen, Pertti

    2017-01-01

    This research is a contribution to issues of digital technology use at the interface of formal and informal learning contexts. The research was conducted in the discourse tradition and investigates Finnish teacher training students' 'manners of speaking' as resources for, and obstacles to, making pedagogical changes in response to the potential of…

  15. Digital technology in mathematics education: Why it works (or doesn’t)

    NARCIS (Netherlands)

    Drijvers, P.H.M.

    2012-01-01

    The integration of digital technology confronts teachers, educators and researchers with many questions. What is the potential of ICT for learning and teaching, and which factors are decisive in making it work in the mathematics classroom? To investigate these questions, six cases from leading studi

  16. Digital technology in mathematics education: why it works (or doesn’t)

    NARCIS (Netherlands)

    Drijvers, P.H.M.

    2013-01-01

    The integration of digital technology confronts teachers, educators and researchers with many questions. What is the potential of ICT for learning and teaching, and which factors are decisive in making it work in the mathematics classroom? To investigate these questions, six cases from leading studi

  17. Digital Technology in Mathematics Education: Why It Works (Or Doesn't)

    Science.gov (United States)

    Drijvers, Paul

    2013-01-01

    The integration of digital technology confronts teachers, educators and researchers with many questions. What is the potential of ICT for learning and teaching, and which factors are decisive in making it work in the mathematics classroom? To investigate these questions, six cases from leading studies in the field are described, and decisive…

  18. Feasibility Study of Analogue and Digital Temperature Sensors in Nanoscale CMOS Technologies

    NARCIS (Netherlands)

    Geljon, M.; Sill, F.; De Lima Monteiro, D.W.

    2009-01-01

    The downscaling of CMOS technology gives rise to a myriad of nanoscale effects. At the same time, power density and thus heat generation increases. The aim of this paper is to evaluate the feasibility of both analogue and digital temperature sensors in nanoscale CMOS using the Berkeley Predictive Te

  19. Exploring the Impact of Digital Technologies on Professional Responsibilities and Education

    Science.gov (United States)

    Fenwick, Tara; Edwards, Richard

    2016-01-01

    Digital technologies in combination with "big" data and predictive analytics are having a significant impact upon professional practices at individual, organisational, national and international levels. The interplay of code, algorithms and big data are increasingly pervasive in the governing, leadership and practices of different…

  20. Pre-Service Teachers' Motivation in Using Digital Technology

    Science.gov (United States)

    Yeung, Alexander S.; Tay, Eng Guan; Hui, Chenri; Lin, Jane Huiling; Low, Ee-Ling

    2014-01-01

    Digital technology (DT) has a significant role to play in modern education. This study examined motivational goals of student teachers in initial teacher education in Singapore and the influences of goals on their use of DT personally and in the classroom. The participants (N = 312) responded to a survey about their motivational goals (learning…

  1. Learning in the Early Years: Social Interactions around Picturebooks, Puzzles and Digital Technologies

    Science.gov (United States)

    Eagle, Sarah

    2012-01-01

    This paper develops an approach to thinking about young children, digital technologies and learning, drawing on research literature that relates children's learning to the use of books, and on literature that discusses the nature of interaction between adults and children and its relationship to children's learning. An analysis is given of parents…

  2. Digital Games as Educational Technology: Promise and Challenges in the Use of Games to Teach

    Science.gov (United States)

    Tobias, Sigmund; Fletcher, J. Dexter; Chen, Fei

    2015-01-01

    Digital games were reviewed as an emerging tool in educational technology. Factors such as instructional effectiveness, time on task, relationship to curricula, student socio-economic status, violence in games, and game mechanics were considered. Despite considerable variability among studies, larger overall effect sizes for the impact of games on…

  3. Young Children (0-8) and Digital Technology : A qualitative exploratory study across seven countries

    OpenAIRE

    CHAUDRON STEPHANE; LAGAE KAAT

    2015-01-01

    Key findings of the JRC's research Young Children (0-8) and Digital Technology : A qualitative exploratory study across seven countries for the Research Highlights series on behalf of the Evidence Group (EG) of the UK Council on Child Internet Safety

  4. 75 FR 65517 - Western Digital Technologies, Inc., Corporate Headquarters/Hard Drive Development Division, Lake...

    Science.gov (United States)

    2010-10-25

    ... Employment and Training Administration Western Digital Technologies, Inc., Corporate Headquarters/Hard Drive Development Division, Lake Forest, CA; Notice of Affirmative Determination Regarding Application for... determination was issued on August 5, 2010 and published in the Federal Register on August 23, 2010 (75 FR...

  5. Investigating Parents' Attitudes towards Digital Technology Use in Early Childhood: A Case Study from Croatia

    Science.gov (United States)

    Mikelic Preradovic, Nives; Lešin, Gordana; Šagud, Mirjana

    2016-01-01

    The aim of this study is to investigate perceptions of parents in Croatia towards advantages and disadvantages of computer use in general as well as their children's computer use and to reveal parents' concerns and opinions about digital technology (DT) education in kindergarten. The paper reports on research findings from one of the large public…

  6. Children under Five and Digital Technologies: Implications for Early Years Pedagogy

    Science.gov (United States)

    Palaiologou, Ioanna

    2016-01-01

    This project aimed to investigate the types of digital technologies children under the age of five are using at home and assess the possible implications for early years pedagogy. The research, carried out between 2010 and 2012, was based in four European countries: England, Greece, Malta and Luxemburg. A mixed methods approach was employed to…

  7. Facilitating English-Language Learners' Oral Reading Fluency with Digital Pen Technology

    Science.gov (United States)

    Chen, Chih-Ming; Tan, Chia-Chen; Lo, Bey-Jane

    2016-01-01

    Oral reading fluency is an indicator of overall reading competence. Many studies have claimed that repeated reading can promote oral reading fluency. Currently, novel Web- or computer-based reading technologies offer interactive digital materials that promote English oral reading fluency using the repeated reading strategy; however, paper-based…

  8. Current Issues and Trends in Multidimensional Sensing Technologies for Digital Media

    Science.gov (United States)

    Nagata, Noriko; Ohki, Hidehiro; Kato, Kunihito; Koshimizu, Hiroyasu; Sagawa, Ryusuke; Fujiwara, Takayuki; Yamashita, Atsushi; Hashimoto, Manabu

    Multidimensional sensing (MDS) technologies have numerous applications in the field of digital media, including the development of audio and visual equipment for human-computer interaction (HCI) and manufacture of data storage devices; furthermore, MDS finds applications in the fields of medicine and marketing, i.e., in e-marketing and the development of diagnosis equipment.

  9. Digital Technology in the Visual Arts Classroom: An [un]Easy Partnership

    Science.gov (United States)

    Wilks, Judith; Cutcher, Alexandra; Wilks, Susan

    2012-01-01

    This article scrutinizes the dichotomy of the uneasy and easy partnerships that exist between digital technology and visual arts education. The claim that by putting computers into schools "we have bought 'one half of a product'... we've bought the infrastructure and the equipment but we haven't bought the educational…

  10. Digital technology in mathematics education : Why it works (or doesn't)

    NARCIS (Netherlands)

    Drijvers, P.H.M.

    2015-01-01

    The integration of digital technology confronts teachers, educators and researchers with many questions. What is the potential of ICT for learning and teaching, and which factors are decisive in making it work in the mathematics classroom? To investigate these questions, six cases from leading studi

  11. Additive and Disruptive Pedagogies: The Use of Slowmation as an Example of Digital Technology Implementation

    Science.gov (United States)

    Vratulis, Vetta; Clarke, Tony; Hoban, Garry; Erickson, Gaalen

    2011-01-01

    The purpose of this study was to explore the experiences of 35 preservice teachers as they were introduced to a new digital technology, "Slowmation" (abbreviated from Slow Animation), as a "disruptive" pedagogy over a period of 12 months. The participants in the study were 35 preservice teachers from an elementary cohort. Primary data sources…

  12. The preliminary conceptions, the traditional resources and digital technologies in teaching of astronomy

    Science.gov (United States)

    de Macedo, J. A.; Voelzke, M. R.

    2014-07-01

    Despite being part of the official documents astronomy is rarely taught adequately in basic education. Digital technologies are commonly used by youth, but neglected by the majority of teachers. In this sense, a survey with the aim of pointing out the potential use of digital technologies in teaching astronomy was developed. An advanced course in astronomy was offered for participants with the goal to make them understand astronomical phenomena. The following steps were to be taken: i) analysis of the pedagogical projects (PPC) of the licenciates at the Federal Institution of the North of Minas Gerais (IFNMG); ii) analysis of students' preconceptions about astronomy and digital technologies; iii) preparation of the course; iv) application of the education proposal. The test consisted of thirty-two students of physics, mathematics and biology and was conducted with the qualitative and quantitative methodology, combined with a content analysis. The results indicated that in the IFNMG only the licenciate-course in physics includes astronomy content diluted in various subjects of the curriculum; the rates of students' prior knowledge in relation to astronomy was low; an evidence of meaningfull earning of the concepts related to astronomy, and of viability of resource use involving digital technologies in the Teaching of astronomy.

  13. Using Digital Technologies to Support Self-Directed Learning for Preservice Teacher Education

    Science.gov (United States)

    Bullock, Shawn Michael

    2013-01-01

    This article begins with the perspective that teacher education programmes are cultural institutions and are thus compelled to respond to the societal push for teachers to be conversant in so-called twenty-first-century skills, grounded primarily in the ability to use digital technologies for pedagogical purposes. The results of an attempt to…

  14. Digital Technology: the Effect of Connected World to Computer Ethic and Family

    Directory of Open Access Journals (Sweden)

    Benfano Soewito

    2015-05-01

    Full Text Available The development of digital technology such as smartphones, tablets and other gadgets grows very rapidly in the last decade so does the development of mobile applications for those mobile systems or smartphones. Unfortunately, those applications often do not specify the age range for their users. This is actually a problem in the world of digital technology and software development. It is not yet known whether the applications is good be used for children or not. Nowadays, parents are faced with the dilemma of allowing their children to use these modern gadgets, which often lead to serious addiction or keeping them in the dark and risk raising ignorant kids. This research shows 80% of respondents agree or strongly agree that the gadget will affect to the development of children social skill. Therefore, in this research, the framework for ethical assessment is introduced and it can be applied to digital technology included gadget and its application in order to mitigate the negative effect of digital technology and gadgets.

  15. Digital Games as Educational Technology: Promise and Challenges in the Use of Games to Teach

    Science.gov (United States)

    Tobias, Sigmund; Fletcher, J. Dexter; Chen, Fei

    2015-01-01

    Digital games were reviewed as an emerging tool in educational technology. Factors such as instructional effectiveness, time on task, relationship to curricula, student socio-economic status, violence in games, and game mechanics were considered. Despite considerable variability among studies, larger overall effect sizes for the impact of games on…

  16. Exploring the Impact of Digital Technologies on Professional Responsibilities and Education

    Science.gov (United States)

    Fenwick, Tara; Edwards, Richard

    2016-01-01

    Digital technologies in combination with "big" data and predictive analytics are having a significant impact upon professional practices at individual, organisational, national and international levels. The interplay of code, algorithms and big data are increasingly pervasive in the governing, leadership and practices of different…

  17. Performance of digital integrated circuit technologies at very high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Prince, J.L.; Draper, B.L.; Rapp, E.A.; Kromberg, J.N.; Fitch, L.T.

    1980-01-01

    Results of investigations of the performance and reliability of digital bipolar and CMOS integrated circuits over the 25 to 340/sup 0/C range are reported. Included in these results are both parametric variation information and analysis of the functional failure mechanisms. Although most of the work was done using commercially available circuits (TTL and CMOS) and test chips from commercially compatible processes, some results of experimental simulations of dielectrically isolated CMOS are also discussed. It was found that commercial Schottky clamped TTL, and dielectrically isolated, low power Schottky-clamped TTL, functioned to junction temperatures in excess of 325/sup 0/C. Standard gold doped TTL functioned only to 250/sup 0/C, while commercial, isolated I/sup 2/L functioned to the range 250/sup 0/C to 275/sup 0/C. Commercial junction isolated CMOS, buffered and unbuffered, functioned to the range 280/sup 0/C to 310/sup 0/C/sup +/, depending on the manufacturer. Experimental simulations of simple dielectrically isolated CMOS integrated circuits, fabricated with heavier doping levels than normal, functioned to temperatures in excess of 340/sup 0/C. High temperature life testing of experimental, silicone-encapsulated simple TTL and CMOS integrated circuits have shown no obvious life limiting problems to date. No barrier to reliable functionality of TTL bipolar or CMOS integrated ciruits at temperatures in excess of 300/sup 0/C has been found.

  18. Exploring Volcanism with Digital Technology in Undergraduate Education

    Science.gov (United States)

    McCoy, F. W.; Parisky, A.

    2016-12-01

    Volcanism as one of the most dynamic geological processes on this planet is also one of the most dramatic for attracting students to the earth sciences. At the University of Hawaii (UH) volcanism is used to attract students into the geosciences, coupled with its significant association to Hawaiian culture and contemporary issues such as those associated with related hazards - example: during the past century five towns were buried by lava flows on the Big Island, another recently threatened with destruction. To bring this dynamism into undergraduate education, UH focuses on field trips and courses to all islands; at Windward Community College (WCC/UH) a focus is provided through a series of field courses (1 credit) to all islands, especially the Big Island. Critical to the WCC effort are computer-generated animations and descriptions of volcanological processes for illustrating concepts undergraduate students find difficult: tumescence as an indicator of an eruption, fractional crystallization, collapse of volcanic edifices, explosive eruptions, weathering processes, hazards and mitigation, all embedded in the evolutionary story of mid-ocean volcanic islands such as those in Hawaii. Field courses require intense field labs, which are significantly assisted by digital platforms that include computer-generated illustrations, descriptions, animations, and more. The consequence for developing geoscientists has been outstanding.

  19. Research on Digital Watermark Using Pre-Processing Technology

    Institute of Scientific and Technical Information of China (English)

    Ru Guo-bao; Ru Guo-bao; Niu Hui-fang; Niu Hui-fang; Yang Rui; Yang Rui; Sun Hong; Sun Hong; Shi Hong-ling; Shi Hong-ling; Huang Tian-xi; Huang Tian-xi

    2003-01-01

    We have realized a watermark embedding system based on audio perceptual masking and brought forward a watermark detection system using pre-processing technology.We can detect watermark from watermarked audio without original audio by using this method. The results have indicated that this embedding and detecting method is robust, on the premise of not affecting the hearing quality, it can resist those attacks such as MPEG compressing, filtering and adding white noise.

  20. The Digital Economy: Social Interaction Technologies – an Overview

    Directory of Open Access Journals (Sweden)

    Teófilo Redondo

    2015-03-01

    Full Text Available Social interaction technologies (SIT is a very broad field that encompasses a large list of topics: interactive and networked computing, mobile social services and the Social Web, social software and social media, marketing and advertising, various aspects and uses of blogs and podcasting, corporate value and web-based collaboration, e-government and online democracy, virtual volunteering, different aspects and uses of folksonomies, tagging and the social semantic cloud of tags, blog-based knowledge management systems, systems of online learning, with their ePortfolios, blogs and wikis in education and journalism, legal issues and social interaction technology, dataveillance and online fraud, neogeography, social software usability, social software in libraries and nonprofit organizations, and broadband visual communication technology for enhancing social interaction. The fact is that the daily activities of many businesses are being socialized, as is the case with Yammer (https://www.yammer.com/, the social enterprise social network. The leitmotivs of social software are: create, connect, contribute, and collaborate.

  1. Exploring the Digital Divide: The Use of Digital Technologies in Ontario Public Schools

    Science.gov (United States)

    Chen, Bodong

    2015-01-01

    Combining data from a school principal survey with student demographics and achievement data, the present study aimed to develop a much needed understanding of ICT usage in Ontario's K-12 public schools. Results indicated equitable first-order access to technology for schools, early integration of ICT from the earliest grades, frequent application…

  2. Ethical perspectives on recommending digital technology for patients with mental illness.

    Science.gov (United States)

    Bauer, Michael; Glenn, Tasha; Monteith, Scott; Bauer, Rita; Whybrow, Peter C; Geddes, John

    2017-12-01

    The digital revolution in medicine not only offers exciting new directions for the treatment of mental illness, but also presents challenges to patient privacy and security. Changes in medicine are part of the complex digital economy based on creating value from analysis of behavioral data acquired by the tracking of daily digital activities. Without an understanding of the digital economy, recommending the use of technology to patients with mental illness can inadvertently lead to harm. Behavioral data are sold in the secondary data market, combined with other data from many sources, and used in algorithms that automatically classify people. These classifications are used in commerce and government, may be discriminatory, and result in non-medical harm to patients with mental illness. There is also potential for medical harm related to poor quality online information, self-diagnosis and self-treatment, passive monitoring, and the use of unvalidated smartphone apps. The goal of this paper is to increase awareness and foster discussion of the new ethical issues. To maximize the potential of technology to help patients with mental illness, physicians need education about the digital economy, and patients need help understanding the appropriate use and limitations of online websites and smartphone apps.

  3. Transitions in the wrong direction? Digital technologies and daily life

    DEFF Research Database (Denmark)

    Røpke, Inge; Christensen, Toke Haunstrup

    2013-01-01

    The environmental implications of information and communication technology (ICT) have been the subject of study since the early 1990s. Although previous research covers energy issues quite extensively, the treatment of the energy impacts of ICT integration in everyday life is still inadequate....... The purpose of this paper is to complement the existing research by applying a perspective in which everyday life takes centre stage. A theoretical framework for describing and analysing the energy impacts of everyday life is outlined, based on a combination of practice theory and time geography...

  4. Exploring the Digital Divide: The Use of Digital Technologies in Ontario Public Schools

    Directory of Open Access Journals (Sweden)

    Bodong Chen

    2015-10-01

    Full Text Available Combining data from a school principal survey with student demographics and achievement data, the present study aimed to develop a much needed understanding of ICT usage in Ontario’s K-12 public schools. Results indicated equitable first-order access to technology for schools, early integration of ICT from the earliest grades, frequent application of ICT in teaching, and an enabling effect of ICT on additional access to learning resources and distance learning. However, challenges were also uncovered in building technology infrastructure for a small fraction of schools; ensuring home access for schools with lower family incomes, smaller size or from remote regions; and providing teachers with professional development for choosing online materials and adopting emerging ICT-enabled teaching practice. Furthermore, this study highlighted the importance of parent involvement in ICT usage and the potential beneficial linkage between ICT usage and student learning achievement.

  5. Interference Rejection in Receivers by Frequency Translated Low‐Pass Filtering and Digitally Enhanced Harmonic‐Rejection Mixing

    NARCIS (Netherlands)

    Klumperink, Eric; Ru, Zhiyu; Moseley, Niels; Nauta, Bram

    2011-01-01

    Software-Defined Radio (SDR) and Cognitive Radio (CR) concepts have recently drawn considerable interest. These radio concepts built on digital signal processing to realize flexibly programmable radio transceivers, which can adapt in a smart way to their environment. As CMOS is the mainstream IC tec

  6. Experimental demonstration of adaptive digital monitoring and compensation of chromatic dispersion for coherent DP-QPSK receiver

    DEFF Research Database (Denmark)

    Borkowski, Robert; Zhang, Xu; Zibar, Darko;

    2011-01-01

    We experimentally demonstrate a digital signal processing (DSP)-based optical performance monitoring (OPM) algorithm for inservice monitoring of chromatic dispersion (CD) in coherent transport networks. Dispersion accumulated in 40 Gbit/s QPSK signal after 80 km of fiber transmission is successfu...

  7. Designing a Deeply Digital Science Curriculum: Supporting Teacher Learning and Implementation with Organizing Technologies

    Science.gov (United States)

    Leary, Heather; Severance, Samuel; Penuel, William R.; Quigley, David; Sumner, Tamara; Devaul, Holly

    2016-02-01

    This paper examines the impacts of technology (e.g., Chromebooks, Google Drive) on teacher learning and student activity in the development and implementation of a deeply digital high school biology unit. Using design-based implementation research, teachers co-designed with researchers and curriculum specialists a student-centered unit aligned to the Next Generation Science Standards (NGSS) that utilizes classroom technology. Qualitative and quantitative data were collected to understand the barriers that inhibit the implementation of a digital curriculum as well as the extent that teachers engage in the design process and begin to make shifts in their practice. We found that through the co-design process teachers began to shift their knowledge of NGSS, technology implementation, and adapted to tensions and barriers inherent in the process.

  8. Privacy Impacts of Data Encryption on the Efficiency of Digital Forensics Technology

    Directory of Open Access Journals (Sweden)

    Adedayo M. Balogun

    2013-06-01

    Full Text Available Owing to a number of reasons, the deployment of encryption solutions are beginning to be ubiquitous at both organizational and individual levels. The most emphasized reason is the necessity to ensure confidentiality of privileged information. Unfortunately, it is also popular as cyber-criminals' escape route from the grasp of digital forensic investigations. The direct encryption of data or indirect encryption of storage devices, more often than not, prevents access to such information contained therein. This consequently leaves the forensics investigation team, and subsequently the prosecution, little or no evidence to work with, in sixty percent of such cases. However, it is unthinkable to jeopardize the successes brought by encryption technology to information security, in favour of digital forensics technology. This paper examines what data encryption contributes to information security, and then highlights its contributions to digital forensics of disk drives. The paper also discusses the available ways and tools, in digital forensics, to get around the problems constituted by encryption. A particular attention is paid to the Truecrypt encryption solution to illustrate ideas being discussed. It then compares encryption's contributions in both realms, to justify the need for introduction of new technologies to forensically defeat data encryption as the only solution, whilst maintaining the privacy goal of users.

  9. Advanced digital modulation: Communication techniques and monolithic GaAs technology

    Science.gov (United States)

    Wilson, S. G.; Oliver, J. D., Jr.; Kot, R. C.; Richards, C. R.

    1983-01-01

    Communications theory and practice are merged with state-of-the-art technology in IC fabrication, especially monolithic GaAs technology, to examine the general feasibility of a number of advanced technology digital transmission systems. Satellite-channel models with (1) superior throughput, perhaps 2 Gbps; (2) attractive weight and cost; and (3) high RF power and spectrum efficiency are discussed. Transmission techniques possessing reasonably simple architectures capable of monolithic fabrication at high speeds were surveyed. This included a review of amplitude/phase shift keying (APSK) techniques and the continuous-phase-modulation (CPM) methods, of which MSK represents the simplest case.

  10. A Design and Research on Protection of Architectural Heritage Based on Digital Technology

    Directory of Open Access Journals (Sweden)

    Hou Shuang Qing

    2016-01-01

    Full Text Available In the era of digital information, how to reasonably use new-tech and idea for the architectural heritage protection remains urgent. In terms of digital protection, 3D laser scanning technology can perfectly remedy the manual measurement limitation thus correctly obtaining the relevant data. Via analysis, we find that the architectural heritage bears in itself the parameterized characteristic. As Building Information Modeling (BIM can help realize the parametric design, we proposed a feasible Architectural Heritage Information Model with the BIM “family” connecting architectural heritage and BIM. Finally, the parameter-induced graphic driving is achieved based on the relation between the two.

  11. Changes in Everyday and Digital Health Technology Use among Seniors in Declining Health.

    Science.gov (United States)

    Levine, David M; Lipsitz, Stuart R; Linder, Jeffrey A

    2017-06-12

    US seniors' digital health and everyday technology use when their health declines are unknown. Longitudinal cohort using the National Health and Aging Trends Study, a nationally-representative, annually-administered sample of community-dwelling Medicare beneficiaries (n=4037). We used difference-in-differences to assess the adjusted difference (AD) in technology use from 2011-2014 between those with and without health declines. Health decline measures included new-onset dementia; new-onset depression; decreases in activities of daily living (ADLs), short physical performance battery (SPPB), grip strength, and self-reported health; relocation to nursing facility; increased hospitalizations; and new-onset comorbidity. Digital health included use of the Internet to research health conditions, contact clinicians, fill prescriptions, and address insurance matters. Between 2011-2014, seniors experiencing health decline used various digital health technologies at low absolute rates (range: 1%-20%). Between 2011-2014, use of everyday technology decreased significantly among seniors with new-onset dementia (from 73% to 51%; AD, -26%), decreased ADLs (from 76% to 67%; AD, -10%), decreased SPPB (from 88% to 86%; AD, -3%), and relocation to a nursing facility (from 49% to 22%; AD, -31%) compared to seniors without comparable decline (all pdigital health decreased significantly among seniors with new-onset probable dementia (from 9% to 4%; AD, -6%) and decreased SPPB (from 24% to 25%; AD -4%; all phealth decline a senior experiences predicts technology use, which may allow better targeting of digital health to specific seniors. Seniors with new dementia, relocation to a nursing home, and declining physical performance seem especially poor candidates for technology interventions.

  12. Race, gender, and information technology use: the new digital divide.

    Science.gov (United States)

    Jackson, Linda A; Zhao, Yong; Kolenic, Anthony; Fitzgerald, Hiram E; Harold, Rena; Von Eye, Alexander

    2008-08-01

    This research examined race and gender differences in the intensity and nature of IT use and whether IT use predicted academic performance. A sample of 515 children (172 African Americans and 343 Caucasian Americans), average age 12 years old, completed surveys as part of their participation in the Children and Technology Project. Findings indicated race and gender differences in the intensity of IT use; African American males were the least intense users of computers and the Internet, and African American females were the most intense users of the Internet. Males, regardless of race, were the most intense videogame players, and females, regardless of race, were the most intense cell phone users. IT use predicted children's academic performance. Length of time using computers and the Internet was a positive predictor of academic performance, whereas amount of time spent playing videogames was a negative predictor. Implications of the findings for bringing IT to African American males and bringing African American males to IT are discussed.

  13. Transitions in the wrong direction? Digital technologies and daily life

    DEFF Research Database (Denmark)

    Røpke, Inge; Christensen, Toke Haunstrup

    2013-01-01

    The environmental implications of information and communication technology (ICT) have been the subject of study since the early 1990s. Although previous research covers energy issues quite extensively, the treatment of the energy impacts of ICT integration in everyday life is still inadequate....... The purpose of this paper is to complement the existing research by applying a perspective in which everyday life takes centre stage. A theoretical framework for describing and analysing the energy impacts of everyday life is outlined, based on a combination of practice theory and time geography....... The framework is applied to a discussion of how ICT co-develops with changing everyday practices and energy-demanding features of everyday life. Based on empirical findings, we explore how the use of ICT affects practices in relation to time and space, and it is argued that observed changes may increase energy...

  14. Putting agricultural equipment and digital technologies at the cutting edge of agroecology

    Directory of Open Access Journals (Sweden)

    Bellon Maurel Véronique

    2017-05-01

    Full Text Available The agro-ecological transition is an ambitious challenge. It can be met by implementing the fundamentals of agroecology (use of biodiversity, integration of agriculture in landscapes, closure of flow loops in the context of a broad and renewed offer of technologies: agro-equipment, biotechnology, digital technologies… This article explores the role that agro-equipment and digital services can play in this transition. These technologies contribute through various levers to the agro-ecological transition: by improving farming efficiency (more service rendered for the same environmental impact, by precision farming (adaptation of the operations to the needs of the plant or the animal based on a monitoring–diagnosis–recommendation cycle and by the development of specialized machinery helping the farmer to achieve “flow loop-closing” (at the plot level, by maintaining the soil quality, or at the farm level, with the recycling of organic effluents or to take advantage of biodiversity (e.g., with agro-equipment adapted to mixed crops. The technological bricks that are requested and for which advances are expected are: sensors (to measure plant or animal needs and associated digital technologies (information transfer, data processing, precision technologies for input application, robotics, specialized machines to manage soil cover and weeds, or for agroforestry. The brakes and engines for innovation in agro-equipment are studied. The brakes are the generally small structure of the farm manufacturing companies, the deficit of the demand from farmers and the complexity − either real or perceived − of these equipments. To encourage innovation, several levers are to be used: involving users in the design of agro-equipments, creating financial incentives for innovative equipment purchase, and training end-users, prescribers and dealers to the high potential of these new technologies. In conclusion, putting agro-equipment and digital technology

  15. Education of hand rubbing technique to prospective medical staff, employing UV-based digital imaging technology.

    Science.gov (United States)

    Lehotsky, Ákos; Szilágyi, László; Demeter-Iclănzan, Annamária; Haidegger, Tamás; Wéber, György

    2016-06-01

    The aim of this study was to objectively assess the hand hygiene performance of medical students. Hand rubbing technique was evaluated by employing innovative UV-light-based imaging technology, identifying patterns and trends in missed areas after applying WHO's six-step protocol. This specially designed hand hygiene education and assessment program targeted 1,344 medical students at two distant sites in Central Europe. Students were introduced to a short video, presenting the basics of hand hygiene, and then received further demonstration from professional trainers, focusing on the correct execution of WHO's six-step technique. To verify the acquired skill, participants rubbed their hands with UV-marked alcohol-based solution. Digital images of the hands were recorded under UV light, followed by computer evaluation and assessment. Immediate objective visual feedback was given to the participants showing missed areas on their hands. The statistical analysis of missed spots was based on retrospective expert-driven manual evaluation. Significant difference in rubbing quality was found between female and male participants [35.3% (CI 95%: 33-38%) versus 29.0% (CI 95%: 27-31%), p hands [43.4% (CI 95%: 39-48%) versus 34.9% (CI 95%: 32-38%), p = 0.002], and various zones of the hands' dorsal side. Based on the participants' feedback and the evaluation of the infection control specialists, it can be stated that the identification of typically missed patterns and the instant visual feedback have a vital role in improving the hand hygiene technique of prospective medical staff.

  16. Preservation of Earth Science Data History with Digital Content Repository Technology

    Science.gov (United States)

    Wei, Y.; Pan, J.; Shrestha, B.; Cook, R. B.

    2011-12-01

    An increasing need for derived and on-demand data product in Earth Science research makes the digital content more difficult for providers to manage and preserve and for users to locate, understand, and consume. Specifically, this increasing need presents additional challenges in managing data processing history information and delivering such information to end users. For example, the North American Carbon Program (NACP) Multi-scale Synthesis and Terrestrial Model Intercomparison Project (MsTMIP) chose a modified SYNMAP land cover data as one of the input driver data for participating terrestrial biospheric models. The global 1km resolution SYNMAP data was created by harmonizing 3 remote sensing-based land cover products: GLCC, GLC2000, and the MODIS land cover product. The original SYNMAP land cover data was aggregated into half and quarter degree resolution. It was then enhanced with more detailed grassland and cropland types. Currently, there lacks an effective mechanism to convey this data processing information to different modeling teams for them to determine if a data product meets their needs. It still highly relies on offline human interaction. The NASA-sponsored ORNL DAAC has leveraged the contemporary digital object repository technology to promote the representation, management, and delivery of data processing history and provenance information. Within digital object repository, different data products are managed as objects, with metadata as attributes and content delivery and management services as dissemination methods. Derivation relationships among data products can be semantically referenced between digital objects. Within the repository, data users can easily track a derived data product back to its origin, explorer metadata and documents about each intermediate data product, and discover processing details involved in each derivation step. Coupled with Drupal Web Content Management System, the digital repository interface was enhanced to

  17. [Comparison of LCD and CRT monitors for detection of pulmonary nodules and interstitial lung diseases on digital chest radiographs by using receiver operating characteristic analysis].

    Science.gov (United States)

    Ikeda, Ryuji; Katsuragawa, Shigehiko; Shimonobou, Toshiaki; Hiai, Yasuhiro; Hashida, Masahiro; Awai, Kazuo; Yamashita, Yasuyuki; Doi, Kunio

    2006-05-20

    Soft copy reading of digital images has been practiced commonly in the PACS environment. In this study, we compared liquid-crystal display (LCD) and cathode-ray tube (CRT) monitors for detection of pulmonary nodules and interstitial lung diseases on digital chest radiographs by using receiver operating characteristic (ROC) analysis. Digital chest images with a 1000x1000 matrix size and a 8 bit grayscale were displayed on LCD/CRT monitor with 2M pixels in each observer test. Eight and ten radiologists participated in the observer tests for detection of nodules and interstitial diseases, respectively. In each observer test, radiologists marked their confidence levels for diagnosis of pulmonary nodules or interstitial diseases. The detection performance of radiologists was evaluated by ROC analyses. The average Az values (area under the ROC curve) in detecting pulmonary nodules with LCD and CRT monitors were 0.792 and 0.814, respectively. In addition, the average Az values in detecting interstitial diseases with LCD and CRT monitors were 0.951 and 0.953, respectively. There was no statistically significant difference between LCD and CRT for both detection of pulmonary nodules (P=0.522) and interstitial lung diseases (P=0.869). Therefore, we believe that the LCD monitor instead of the CRT monitor can be used for the diagnosis of pulmonary nodules and interstitial lung diseases in digital chest images.

  18. On the Brain Basis of Digital Daze in Millennial Minds: Rejoinder to "Digital Technology and Student Cognitive Development: The Neuroscience of the University Classroom"

    Science.gov (United States)

    Brown, Timothy T.

    2016-01-01

    In this issue, Cavanaugh, Giapponi, and Golden (2016) have discussed the new prominent role of digital devices in the lives of students; the possible impact of these widely-used technologies on developing, learning minds; and the relevance of new cognitive neuroscience research and technologies for better understanding the potential effects of…

  19. On the Brain Basis of Digital Daze in Millennial Minds: Rejoinder to "Digital Technology and Student Cognitive Development: The Neuroscience of the University Classroom"

    Science.gov (United States)

    Brown, Timothy T.

    2016-01-01

    In this issue, Cavanaugh, Giapponi, and Golden (2016) have discussed the new prominent role of digital devices in the lives of students; the possible impact of these widely-used technologies on developing, learning minds; and the relevance of new cognitive neuroscience research and technologies for better understanding the potential effects of…

  20. Digital Disconnect or Digital Difference? A Socio-Ecological Perspective on Young Children's Technology Use in the Home and the Early Childhood Centre

    Science.gov (United States)

    Edwards, Susan; Henderson, Michael; Gronn, Donna; Scott, Anne; Mirkhil, Moska

    2017-01-01

    A digital disconnect perspective is founded on an assumption that technology use in the home is frequent, creative and generative, and that technology use in the early childhood centre should be the same as that found in the home. However, such arguments divert our attention from understanding the nature of the setting and thereby from an…