Technical area status report for low-level mixed waste final waste forms

International Nuclear Information System (INIS)

Mayberry, J.L.; DeWitt, L.M.; Darnell, R.

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA's Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities

76 FR 18624 - Research, Technical Assistance and Training Programs: Notice of Final Circular

Science.gov (United States)

2011-04-04

... to FTA Circular 6100.1D, Research and Technical Assistance Training Program: Application Instructions... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Research, Technical Assistance and Training Programs: Notice of Final Circular AGENCY: Federal Transit Administration (FTA), DOT. ACTION...

AIMES Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Katz, Daniel S [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Weissman, Jon [Univ. of Minnesota, Minneapolis, MN (United States); Turilli, Matteo [Rutgers Univ., New Brunswick, NJ (United States)

2017-01-31

This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.

NCSU reactor sharing program. Final technical report

International Nuclear Information System (INIS)

Perez, P.B.

1997-01-01

The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities. This report is the Final Technical Report for the DOE award reference number DE-FG05-95NE38136 which covers the period September 30, 1995 through September 30, 1996

High energy physics research. Final technical report, 1957--1994

International Nuclear Information System (INIS)

Williams, H.H.

1995-01-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development

High energy physics research. Final technical report, 1957--1994

Energy Technology Data Exchange (ETDEWEB)

Williams, H.H.

1995-10-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development.

Technical approach to finalizing sensible soil cleanup levels at the Fernald Environmental Management Project

International Nuclear Information System (INIS)

Carr, D.; Hertel, B.; Jewett, M.; Janke, R.; Conner, B.

1996-01-01

The remedial strategy for addressing contaminated environmental media was recently finalized for the US Department of Energy's (DOE) Fernald Environmental Management Project (FEMP) following almost 10 years of detailed technical analysis. The FEMP represents one of the first major nuclear facilities to successfully complete the Remedial Investigation/Feasibility Study (RI/FS) phase of the environmental restoration process. A critical element of this success was the establishment of sensible cleanup levels for contaminated soil and groundwater both on and off the FEMP property. These cleanup levels were derived based upon a strict application of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) regulations and guidance, coupled with positive input from the regulatory agencies and the local community regarding projected future land uses for the site. The approach for establishing the cleanup levels was based upon a Feasibility Study (FS) strategy that examined a bounding range of viable future land uses for the site. Within each land use, the cost and technical implications of a range of health-protective cleanup levels for the environmental media were analyzed. Technical considerations in driving these cleanup levels included: direct exposure routes to viable human receptors; cross- media impacts to air, surface water, and groundwater; technical practicality of attaining the levels; volume of affected media; impact to sensitive environmental receptors or ecosystems; and cost. This paper will discuss the technical approach used to support the finalization of the cleanup levels for the site. The final cleanup levels provide the last remaining significant piece to the puzzle of establishing a final site-wide remedial strategy for the FEMP, and positions the facility for the expedient completion of site-wide remedial activities

Audit of Wolf Creek Generating Station, Unit 1 technical specifications. Final technical evaluation report

International Nuclear Information System (INIS)

Stromberg, H.M.

1985-07-01

This document was prepared for the Nuclear Regulatory Commission (NRC) to assist them in determining whether the Wolf Creek Generating Station Unit 1 Technical Specifications (T/S), which govern plant systems configurations and operations, are in conformance with the assumptions of the Final Safety Analysis Report (FSAR) as amended, the requirements of the Safety Evaluation Report (SER) as supplemented, and the Comments and Responses to the Wolf Creek Technical Specification Draft Inspection Report. A comparative audit of the FSAR as amended, the SER as supplemented, and the Draft Inspection Report was performed with the Wolf Creek T/S. Several discrepancies were identified and subsequently resolved through discussions with the cognizant NRC reviewer, NRC staff reviewers and/or utility representatives. The Wolf Creek Generating Station Unit 1 T/S, to the extent reviewed, are in conformance with the FSAR, SER, and Draft Inspection Report

Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis.

Science.gov (United States)

Knijnenburg, S L; Raemaekers, S; van den Berg, H; van Dijk, I W E M; Lieverst, J A; van der Pal, H J; Jaspers, M W M; Caron, H N; Kremer, L C; van Santen, H M

2013-04-01

Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of 573 CCS. Multivariable regression analyses were carried out to estimate the influence of different determinants on height SDS at follow-up. Overall, survivors had a normal height SDS at cancer diagnosis. However, at follow-up in adulthood, 8.9% had a height ≤-2 SDS. Height SDS at diagnosis was an important determinant for adult height SDS. Children treated with (higher doses of) radiotherapy showed significantly reduced final height SDS. Survivors treated with total body irradiation (TBI) and craniospinal radiation had the greatest loss in height (-1.56 and -1.37 SDS, respectively). Younger age at diagnosis contributed negatively to final height. Height at diagnosis was an important determinant for height SDS at follow-up. Survivors treated with TBI, cranial and craniospinal irradiation should be monitored periodically for adequate linear growth, to enable treatment on time if necessary. For correct interpretation of treatment-related late effects studies in CCS, pre-treatment data should always be included.

Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis

NARCIS (Netherlands)

Knijnenburg, S. L.; Raemaekers, S.; van den Berg, H.; van Dijk, I. W. E. M.; Lieverst, J. A.; van der Pal, H. J.; Jaspers, M. W. M.; Caron, H. N.; Kremer, L. C.; van Santen, H. M.

2013-01-01

Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of

78 FR 12955 - Final Requirements, Definitions, and Selection Criteria-Native American Career and Technical...

Science.gov (United States)

2013-02-26

... career and technical education programs (20 U.S.C. 2326(e)). This notice does not preclude us from... DEPARTMENT OF EDUCATION 34 CFR Chapter IV [Docket ID ED-2012-OVAE-0053] Final Requirements, Definitions, and Selection Criteria--Native American Career and Technical Education Program (NACTEP) [Catalog...

Technical planning activity: Final report

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

Technical planning activity: Final report

International Nuclear Information System (INIS)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

Technical area status report for low-level mixed waste final waste forms. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Mayberry, J.L.; DeWitt, L.M. [Science Applications International Corp., Idaho Falls, ID (United States); Darnell, R. [EG and G Idaho, Inc., Idaho Falls, ID (United States)] [and others

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA`s Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities.

77 FR 30512 - Native American Career and Technical Education Program; Final Waivers and Extension of Project...

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native American Career and Technical Education Program; Final Waivers and... American Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84... and Technical Education Program (NACTEP), the Secretary waives 34 CFR 75.250 and 75.261(c)(2) in order...

"Type Ia Supernovae: Tools for Studying Dark Energy" Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Woosley, Stan [Lick Observatory, San Jose, CA (United States); Kasen, Dan [Univ. of California, Berkeley, CA (United States)

2017-05-10

Final technical report for project "Type Ia Supernovae: Tools for the Study of Dark Energy" awarded jointly to scientists at the University of California, Santa Cruz and Berkeley, for computer modeling, theory and data analysis relevant to the use of Type Ia supernovae as standard candles for cosmology.

Key technical issues associated with a method of pulse compression. Final technical report

International Nuclear Information System (INIS)

Hunter, R.O. Jr.

1980-06-01

Key technical issues for angular multiplexing as a method of pulse compression in a 100 KJ KrF laser have been studied. Environmental issues studied include seismic vibrations man-made vibrations, air propagation, turbulence, and thermal gradient-induced density fluctuations. These studies have been incorporated in the design of mirror mounts and an alignment system, both of which are reported. A design study and performance analysis of the final amplifier have been undertaken. The pulse compression optical train has been designed and assessed as to its performance. Individual components are described and analytical relationships between the optical component size, surface quality, damage threshold and final focus properties are derived. The optical train primary aberrations are obtained and a method for aberration minimization is presented. Cost algorithms for the mirrors, mounts, and electrical hardware are integrated into a cost model to determine system costs as a function of pulse length, aperture size, and spot size

The Michigan high-level radioactive waste program: Final technical progress report

International Nuclear Information System (INIS)

1987-01-01

This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

Final Technical Report, Wind Generator Project (Ann Arbor)

Energy Technology Data Exchange (ETDEWEB)

Geisler, Nathan [City of Ann Arbor, MI (United States)

2017-03-20

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

Iowa Hill Pumped Storage Project Investigations - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hanson, David [Sacramento Municipal Unitlity District, Sacramento, CA (United States)

2016-07-01

This Final Technical Report is a summary of the activities and outcome of the Department of Energy (DOE) Assistance Agreement DE-EE0005414 with the Sacramento Municipal Utility District (SMUD). The Assistance Agreement was created in 2012 to support investigations into the Iowa Hill Pumped-storage Project (Project), a new development that would add an additional 400 MW of capacity to SMUD’s existing 688MW Upper American River Hydroelectric Project (UARP) in the Sierra Nevada mountains east of Sacramento, California.

Admiralty Inlet Pilot Tidal Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Collar, Craig [Public Utility District No. 1 of Snohomish County, Everett, WA (United States)

2015-09-14

This document represents the final report for the Admiralty Inlet Pilot Tidal Project, located in Puget Sound, Washington, United States. The Project purpose was to license, permit, and install a grid-connected deep-water tidal turbine array (two turbines) to be used as a platform to gather operational and environmental data on tidal energy generation. The data could then be used to better inform the viability of commercial tidal energy generation from technical, economic, social, and environmental standpoints. This data would serve as a critical step towards the responsible advancement of commercial scale tidal energy in the United States and around the world. In late 2014, Project activities were discontinued due to escalating costs, and the DOE award was terminated in early 2015. Permitting, licensing, and engineering design activities were completed under this award. Final design, deployment, operation, and monitoring were not completed. This report discusses the results and accomplishments achieved under the subject award.

77 FR 30514 - Native Hawaiian Career and Technical Education Program; Final Waiver and Extension of Project Period

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native Hawaiian Career and Technical Education Program; Final Waiver and... Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84.259A... Technical Education Program (NHCTEP), the Secretary hereby waives 34 CFR 75.261(c)(2) in order to extend the...

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Schuur, Edward [Northern Arizona Univ., Flagstaff, AZ (United States); Luo, Yiqi [Univ. of Oklahoma, Norman, OK (United States)

2016-12-01

This final grant report is a continuation of the final grant report submitted for DE-SC0006982 as the Principle Investigator (Schuur) relocated from the University of Florida to Northern Arizona University. This report summarizes the original project goals, as well as includes new project activities that were completed in the final period of the project.

Characterization of the radon source in North-Central Florida. Final report part 1 -- Final project report; Final report part 2 -- Technical report

International Nuclear Information System (INIS)

1997-01-01

This report contains two separate parts: Characterization of the Radon Source in North-Central Florida (final report part 1 -- final project report); and Characterization of the Radon Source in North-Central Florida (technical report). The objectives were to characterize the radon 222 source in a region having a demonstrated elevated indoor radon potential and having geology, lithology, and climate that are different from those in other regions of the U.S. where radon is being studied. Radon availability and transport in this region were described. Approaches for predicting the radon potential of lands in this region were developed

Non-invasive imaging technics for diagnosis in children with surgical abdominal diseases

International Nuclear Information System (INIS)

Nakada, Koonosuke; Sato, Yutaka; Shimoyamada, Hiroaki; Kim, Yoshitaka; Ishikawa, Misao

1984-01-01

The usefullness of non-invasive imaging technics namely CT and ultrasonography was evaluated in pediatric surgical abdominal diseases, under the categoly of A) inflammatory masses (10), B) biliary abnormalities (6), C) neoplasms (12), and D) blunt abdominal traumas (8), which were experienced at St. Marianna University Hospital from April 1978 to January 1982. According to the results of the clinical study, the plan of useful diagnostic approaches in each group by means of several imaging technics was outlined. In group A and B, ultrasonography is usually suffice for diagnosis and therapy planning, whereas in group C and D, in addition to the ultrasound, CT is sometimes required for evaluating the involvement of vascular structures and sorrounding vital structures in cases of neoplasm, and coexisting injuries in the traumas. (author)

Clean Energy Works Oregon Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacob, Andria [City of Portland; Cyr, Shirley [Clean Energy Works

2013-12-31

In April 2010, the City of Portland received a $20 million award from the U.S. Department of Energy, as part of the Energy Efficiency and Conservation Block Grant program. This award was appropriated under the American Recovery and Reinvestment Act (ARRA), passed by President Obama in 2009. DOE’s program became known as the Better Buildings Neighborhood Program (BBNP). The BBNP grant objectives directed the City of Portland Bureau of Planning and Sustainability (BPS) as the primary grantee to expand the BPS-led pilot program, Clean Energy Works Portland, into Clean Energy Works Oregon (CEWO), with the mission to deliver thousands of home energy retrofits, create jobs, save energy and reduce carbon dioxide emissions.The Final Technical Report explores the successes and lessons learned from the first 3 years of program implementation.

Energy Impact Illinois - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olson, Daniel [Senior Energy Efficiency Planner; Plagman, Emily [Senior Energy Planner; Silberhorn, Joey-Lin [Energy Efficiency Program Assistant

2014-02-18

Energy Impact Illinois (EI2) is an alliance of government organizations, nonprofits, and regional utility companies led by the Chicago Metropolitan Agency for Planning (CMAP) that is dedicated to helping communities in the Chicago metropolitan area become more energy efficient. Originally organized as the Chicago Region Retrofit Ramp-Up (CR3), EI2 became part of the nationwide Better Buildings Neighborhood Program (BBNP) in May 2010 after receiving a $25 million award from the U.S. Department of Energy (DOE) authorized through the American Recovery and Reinvestment Act of 2009 (ARRA). The program’s primary goal was to fund initiatives that mitigate barriers to energy efficiency retrofitting activities across residential, multifamily, and commercial building sectors in the seven-county CMAP region and to help to build a sustainable energy efficiency marketplace. The EI2 Final Technical Report provides a detailed review of the strategies, implementation methods, challenges, lessons learned, and final results of the EI2 program during the initial grant period from 2010-2013. During the program period, EI2 successfully increased direct retrofit activity in the region and was able to make a broader impact on the energy efficiency market in the Chicago region. As the period of performance for the initial grant comes to an end, EI2’s legacy raises the bar for the region in terms of helping homeowners and building owners to take action on the continually complex issue of energy efficiency.

Final Technical Report for DE-FG02-98ER45737

Energy Technology Data Exchange (ETDEWEB)

Ade, Harald W.

2018-04-24

Final Technical Report For DOE Grant No. DE-FG02-98ER45737 Development of a Scanning Transmission X-Ray Microscope Polymer Thin Films and Self Assembled Monolayers: Pattern Formation and Surface Interactions NEXAFS Microscopy and Resonant Scattering of Polymeric Materials Organic Heterojunction Devices: Structure, Composition, and Performance at <20 nm Resolution Fundamental Science of High Open Circuit Voltage Excitonic Solar Cells Control of Interface- and Mesoscopic Structure in High Performance Organic Solar Cells: Towards a Predictive Device Paradigm

Summary report of the final technical meeting on 'International Reactor Dosimetry File: IRDF-2002'

International Nuclear Information System (INIS)

Griffin, Patrick J.; Paviotti-Corcuera, R.

2003-10-01

Presentations, recommendations and conclusions of the Final Technical Meeting on 'International Reactor Dosimetry File: IRDF-2002' are summarized in this report. The main aims of this meeting were to discuss scientific and technical matters related to reactor dosimetry and to assign responsibilities for the preparation of the final version of the IRDF- 2002 library and the associated TECDOC. Tasks were assigned and deadlines were agreed. Participants emphasized that accurate and complete nuclear data for reactor dosimetry are essential to improve the assessment accuracies for reactor pressure vessel service lifetimes in nuclear power plants, as well as for other neutron metrology applications such as boron neutron capture therapy, therapeutic use of medical isotopes, nuclear physics measurements, and reactor safety applications. (author)

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

2016-08-17

ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

DE-FG02-04ER63746 FinalTechnicalReport

Energy Technology Data Exchange (ETDEWEB)

Lidstrom, M.E.

2009-09-05

This is the final technical report for a project involving the study of stress response systems in the radiation-resistant bacterium, Deinococcus radiodurans. Three stresses of importance for a mixed waste treatment strain were studied, heat shock, solvent shock, and phosphate starvation. In each case, specific genes involved in the ability to survive the stress were identified using a systems biology approach, and analysis of mutants was used to understand mechanisms. This study has led to increased understanding of the ways in which a potential treatment strain could be manipulated to survive multiple stresses for treatment of mixed wastes.

Evaluation of the contribution of radiological imaging to the final diagnosis in medical case reports

International Nuclear Information System (INIS)

Wiesinger, Isabel; Scharf, Gregor; Platz, Natascha; Dendl, Lena M.; Stroszczynski, Christian; Schreyer, Andreas G.; Pawlik, Michael T.

2015-01-01

To evaluate the clinical value and impact of radiological imaging in published medial case reports. We analysed 671 consecutively published case reports of a peer-reviewed medical journal for case reports. The general use of radiological imaging as well as the specific imaging modality used in each case (ultrasound, x-ray, fluoroscopy, CT, MRI) was documented, and most importantly the 'final problem solver', i.e. the diagnostic modality giving the final clue to the patient's diagnosis, was identified. In 511 of 671 (76.1 %) analysed case reports at least one radiological modality was used in the diagnostic cascade. In 28.6 % of all cases the final diagnosis was achieved by radiological imaging. All other cases were solved by the patient's history and physical examination (15.2 %), histology (12.4 %), and blood analysis (9.6 %). When radiology was the 'final problem solver', it was mainly CT (51.6 %) and MRI (30.6 %). In 52.2 % of the case reports the radiological image was included in the article. In case reports published in a prominent general medical journal radiological imaging is an important key player in the diagnostic process. In many cases, it is also the diagnostic tool which ultimately leads to determining the final diagnosis. (orig.)

Evaluation of the contribution of radiological imaging to the final diagnosis in medical case reports

Energy Technology Data Exchange (ETDEWEB)

Wiesinger, Isabel; Scharf, Gregor; Platz, Natascha; Dendl, Lena M.; Stroszczynski, Christian; Schreyer, Andreas G. [University Hospital Regensburg, Institute of Radiology, Regensburg (Germany); Pawlik, Michael T. [Intensive Care and Emergency Medicine, Institute of Anaesthesiology, Regensburg (Germany)

2015-05-01

To evaluate the clinical value and impact of radiological imaging in published medial case reports. We analysed 671 consecutively published case reports of a peer-reviewed medical journal for case reports. The general use of radiological imaging as well as the specific imaging modality used in each case (ultrasound, x-ray, fluoroscopy, CT, MRI) was documented, and most importantly the 'final problem solver', i.e. the diagnostic modality giving the final clue to the patient's diagnosis, was identified. In 511 of 671 (76.1 %) analysed case reports at least one radiological modality was used in the diagnostic cascade. In 28.6 % of all cases the final diagnosis was achieved by radiological imaging. All other cases were solved by the patient's history and physical examination (15.2 %), histology (12.4 %), and blood analysis (9.6 %). When radiology was the 'final problem solver', it was mainly CT (51.6 %) and MRI (30.6 %). In 52.2 % of the case reports the radiological image was included in the article. In case reports published in a prominent general medical journal radiological imaging is an important key player in the diagnostic process. In many cases, it is also the diagnostic tool which ultimately leads to determining the final diagnosis. (orig.)

Mathematics Intensive Summer Session (MISS). Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

This final technical report appears in two parts: the report for the 1995 summer MISS program and the report for the 1996 summer MISS program. Copies of the US Department of Energy Pre-Freshman Enrichment Program 1995 Entry Form and 1996 Entry Form completed by all participants were sent to the Oak Ridge Institute for Science and Education in the fall of 1995 and 1996 respectively. Those forms are on file should they be needed. Attached also is a copy of the Summary of ideas for panel discussions, problem-solving sessions, or small group discussions presented at the Department of Energy Oak Ridge Institute for Science and Education Pre-Freshman Enrichment Program Project Directors Meeting held in San Antonio, TX, November 12--14, 1995.

Technical and economic assessment of solar hybrid repowering. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1978-09-01

Public Service Company of New Mexico (PNM) has performed a Technical and Economic Assessment of Solar Hybrid Repowering under funding by the Department of Energy (DOE), the Electric Power Research Institute (EPRI), Western Energy Supply and Transmission (WEST) Associates, and a number of southwestern utilities. Solar hybrid repowering involves placement of solar hardware adjacent to and connected to existing gas- and oil-fueled electric generation units to displace some of or all the fossil fuel normally used during daylight hours. The subject study assesses the technical economic viability of the solar hybrid repowering concept within the southwestern United States and the PNM system. This document is a final report on the study and its results. The study was divided into the six primary tasks to allow a systematic investigation of the concept: (1) market survey and cost/benefit analysis, (2) study unit selection, (3) conceptual design and cost estimates, (4) unit economic analysis, (5) program planning, future phases, and (6) program management. Reeves Station No. 2 at Albuquerque, New Mexico, was selected for repowering with a design goal of 50 percent (25 MWe). The solar system design is based on the 10 MW solar central receiver pilot plant preliminary design for Barstow, California. SAN--1608-4-2 contains the technical drawings. (WHK)

The value of auditing negative lower GI investigations preceding a final diagnosis of colorectal cancer.

Science.gov (United States)

Somasekar, A; James, L; Stephenson, B M; Thompson, I W; Vellacott, K D; Allison, M C

2009-09-01

To review all preceding 'negative' large bowel investigations in patients with a final diagnosis of colorectal cancer, and to examine whether delayed diagnosis was associated with worse outcome. Details were gathered on all patients with a new diagnosis of colorectal adenocarcinoma presenting over 4.5 years. For each patient the hospital's clinical workstation and radiology and endoscopy databases were interrogated for all flexible sigmoidoscopies, colonoscopies and barium enemas during the 5 years prior to diagnosis. Among the 570 patients, 28 (5%) had undergone colonoscopy and/or flexible sigmoidoscopy that had not shown colorectal cancer during the 5 years preceding final diagnosis, and a further 28 (5%) had undergone 'negative' barium enemas. Polyp surveillance might have missed four lesions destined to become malignant. Correspondingly there were three patients undergoing IBD surveillance found to have CRC, having had a negative complete colonoscopy within the preceding 5 years. Among patients undergoing de novo colonoscopy for diagnosis the true miss rate was only one patient per year. At August 2007, 29 (58%) of those with delayed diagnosis were still alive, compared with 216 (42%) of those diagnosed during initial investigation (chi2 = 5.04, P auditing the quality assurance of lower gastrointestinal diagnostic services. Despite the delay, late diagnosis was found to be associated with improved survival and a lower likelihood of metastatic disease.

More on Darwin's illness: comment on the final diagnosis of Charles Darwin.

Science.gov (United States)

Sheehan, William; Meller, William H; Thurber, Steven

2008-06-20

Without the possibility of confirmatory exhumation, diagnostic inferences about Darwin's illness must remain speculative. A diagnosis of Darwin's aggregate symptoms must account for not only gastrointestinal distress but also his predominant and excessive retching and the conglomerate of other heterogeneous symptoms. We opine that Crohn's disease, posited as the 'final diagnosis', is not sufficient for subsuming his pleiomorphic symptomatology. An additional proposal is outlined that may help to explain his presentation with heterogeneous symptoms. It incorporates constitutional vulnerabilities, psychosomatic influences and Pavlovian conditioning as explanatory variables.

University of Maryland component of the Center for Multiscale Plasma Dynamics: Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Dorland, William [University of Maryland

2014-11-18

The Center for Multiscale Plasma Dynamics (CMPD) was a five-year Fusion Science Center. The University of Maryland (UMD) and UCLA were the host universities. This final technical report describes the physics results from the UMD CMPD.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bohdan W. Oppenheim; Rudolf Marloth

2007-10-26

Executive Summary The document contains Final Technical Report on the Industrial Assessment Center Program at Loyola Marymount University in Los Angeles, covering the contract period of 9/1/2002 to 11/30/2006, under the contract DE-FC36-02GO 12073. The Report describes six required program tasks, as follows: TASK 1 is a summary of the assessments performed over the life of the award: 77 assessments were performed, 595 AR were recommended, covering a very broad range of manufacturing plants. TASK 2 is a description of the efforts to promote and increase the adoption of assessment recommendations and employ innovative methods to assist in accomplishing these goals. The LMU IAC has been very successful in accomplishing the program goals, including implemented savings of $5,141,895 in energy, $10,045,411 in productivity and $30,719 in waste, for a total of $15,218,025. This represents 44% of the recommended savings of $34,896,392. TASK 3 is a description of the efforts promoting the IAC Program and enhancing recruitment efforts for new clients and expanded geographic coverage. LMU IAC has been very successful recruiting new clients covering Southern California. Every year, the intended number of clients was recruited. TASK 4 describes the educational opportunities, training, and other related activities for IAC students. A total of 38 students graduated from the program, including 2-3 graduate students every semester, and the remainder undergraduate students, mostly from the Mechanical Engineering Department. The students received formal weekly training in energy (75%) and productivity (25). All students underwent extensive safety training. All students praised the IAC experience very highly. TASK 5 describes the coordination and integration of the Center activities with other Center and IAC Program activities, and DOE programs. LMU IAC worked closely with MIT, and SDSU IAC and SFSU IAC, and enthusiastically supported the SEN activities. TASK 6 describes other tasks

Technical report—Diagnosis and management of an initial UTI in febrile infants and young children.

Science.gov (United States)

Finnell, S Maria E; Carroll, Aaron E; Downs, Stephen M

2011-09-01

The diagnosis and management of urinary tract infections (UTIs) in young children are clinically challenging. This report was developed to inform the revised, evidence-based, clinical guideline regarding the diagnosis and management of initial UTIs in febrile infants and young children, 2 to 24 months of age, from the American Academy of Pediatrics Subcommittee on Urinary Tract Infection. The conceptual model presented in the 1999 technical report was updated after a comprehensive review of published literature. Studies with potentially new information or with evidence that reinforced the 1999 technical report were retained. Meta-analyses on the effectiveness of antimicrobial prophylaxis to prevent recurrent UTI were performed. Review of recent literature revealed new evidence in the following areas. Certain clinical findings and new urinalysis methods can help clinicians identify febrile children at very low risk of UTI. Oral antimicrobial therapy is as effective as parenteral therapy in treating UTI. Data from published, randomized controlled trials do not support antimicrobial prophylaxis to prevent febrile UTI when vesicoureteral reflux is found through voiding cystourethrography. Ultrasonography of the urinary tract after the first UTI has poor sensitivity. Early antimicrobial treatment may decrease the risk of renal damage from UTI. Recent literature agrees with most of the evidence presented in the 1999 technical report, but meta-analyses of data from recent, randomized controlled trials do not support antimicrobial prophylaxis to prevent febrile UTI. This finding argues against voiding cystourethrography after the first UTI.

Gap analysis between provisional diagnosis and final diagnosis in government and private teaching hospitals: A record-linked comparative study.

Science.gov (United States)

Chatterjee, Sudeshna; Ray, Krishnangshu; Das, Anup Kumar

2016-01-01

1. To identify the extent of clinical gaps at the context of knowledge, practice and systems. 2. To formulate necessary intervention measures towards bridging the gaps. Comparative, cross-sectional and non-interventional study. It is retrospective, record-based study conducted upon inpatients ( n = 200) of major disciplines of two teaching hospitals. Major outcome variables were to observe the matching and un-matching of final and provisional diagnosis by using ICD-10 criteria. Comparative analysis of specific and selective gaps were estimated in terms of percentage (%). Pilot observation showed the existence of gaps between provisional and final diagnosis in both private and government institution. Both knowledge and skill gaps were evident in caregivers and gap in documentation was existent in medical records. The pilot data is may be an eye-opener to public and private governance systems for understanding and revising the process service planning and service delivery. Necessary intervention measures may be contemplated towards enhancing diagnostic skill of doctors for quality hospital care.

Ways to Determine the Technical Status of the Vehicles’ Braking System by Means of General Diagnosis

Directory of Open Access Journals (Sweden)

Todea Paul

2017-06-01

Full Text Available Vehicles’ breaking system is one of the basic elements that lead to the maintenance of technical and road safety during transport activities on public roads or other special conditions. Therefore, particular attention is paid to all maintenance work planned or occasionally carried out on such system, as a high coefficient of vehicles availability results in an increased percentage of their productivity. Of course, there is diagnosis equipment for each element, and the brake booths within MOT centres accurately indicate the values of the measured parameters, following repair, adjustment and control operations for troubleshooting. Still, there are certain cases requesting the check of breaking system either analytically or by field experiments, i.e. when vehicles are driven on rough and rugged ground, during military specific missions and activities, where their performance no longer allows specialized equipment or when such equipment does not exist. This works presents alternatives to determine the technical condition of the braking system by means of typical solutions for the general diagnosis type.

Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS): Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

de Boer, Gijs [Univ. of Colorado, Boulder, CO (United States); Lawrence, Dale [Univ. of Colorado, Boulder, CO (United States); Palo, Scott [Univ. of Colorado, Boulder, CO (United States); Argrow, Brian [Univ. of Colorado, Boulder, CO (United States); LoDolce, Gabriel [Univ. of Colorado, Boulder, CO (United States); Curry, Nathan [Univ. of Colorado, Boulder, CO (United States); Weibel, Douglas [Univ. of Colorado, Boulder, CO (United States); Finamore, William [Univ. of Colorado, Boulder, CO (United States); D' Amore, Phillip [Univ. of Colorado, Boulder, CO (United States); Borenstein, Steven [Univ. of Colorado, Boulder, CO (United States); Nichols, Tevis [Univ. of Colorado, Boulder, CO (United States); Elston, Jack [Blackswift Technologies, Boulder, CO (United States); Ivey, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bendure, Albert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schmid, Beat [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Long, Charles [Univ. of Colorado, Boulder, CO (United States); Telg, Hagen [Univ. of Colorado, Boulder, CO (United States); Gao, Ru-Shan [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); Hock, Terry [National Center for Atmospheric Research, Boulder, CO (United States); Bland, Geoff [NASA Ames Research Center (ARC), Moffett Field, Mountain View, CA (United States)

2017-03-29

This final technical report details activities undertaken as part of the referenced project. Included is information on the preparation of aircraft for deployment to Alaska, summaries of the three deployments covered under this project, and a brief description of the dataset and science directions pursued. Additionally, we provide information on lessons learned, publications, and presentations resulting from this work.

Final Technical Report for contract number DE-FG02-05ER15670

Energy Technology Data Exchange (ETDEWEB)

Glazebrook, Jane [Univ. of Minnesota, Minneapolis, MN (United States)

2016-02-29

This is the final technical report for contract number DE-FG02-05ER15670. The project is now complete, and results of the project have been published. Two papers were published based on work done in the last three-year funding period. The DOIs of these papers are included below. The abstracts of the papers, providing summaries of the work, are included in the body of the report.

Technical and logistic provisions for the delivery of radioactive wastes in the final repository Konrad

International Nuclear Information System (INIS)

Poeppinghaus, Jens

2013-01-01

The beginning of radioactive waste delivery to the final repository Konrad is planned for 2019. The main issue for the technical and logistic provisions is the development of a concept for the transport of the licensed radioactive waste containers to the site, including a turning concept for cylindrical waste forms and planning, construction and manufacture of transport equipment. Further issues include a logistic concept considering specific boundary conditions as administrative processes, priorities, special features of the delivering institutions and technical requirements of the repository.

Gap analysis between provisional diagnosis and final diagnosis in government and private teaching hospitals: A record-linked comparative study

Directory of Open Access Journals (Sweden)

Sudeshna Chatterjee

2016-01-01

Full Text Available Aims: 1. To identify the extent of clinical gaps at the context of knowledge, practice and systems. 2. To formulate necessary intervention measures towards bridging the gaps. Settings and Design: Comparative, cross-sectional and non-interventional study. Methods and Material: It is retrospective, record-based study conducted upon inpatients (n = 200 of major disciplines of two teaching hospitals. Major outcome variables were to observe the matching and un-matching of final and provisional diagnosis by using ICD-10 criteria. Statistical Analysis Used: Comparative analysis of specific and selective gaps were estimated in terms of percentage (%. Results: Pilot observation showed the existence of gaps between provisional and final diagnosis in both private and government institution. Both knowledge and skill gaps were evident in caregivers and gap in documentation was existent in medical records. Conclusions: The pilot data is may be an eye-opener to public and private governance systems for understanding and revising the process service planning and service delivery. Necessary intervention measures may be contemplated towards enhancing diagnostic skill of doctors for quality hospital care.

An Annotated Selective Bibliography on Human Performance in Fault Diagnosis Tasks. Technical Report 435. Final Report.

Science.gov (United States)

Johnson, William B.; And Others

This annotated bibliography developed in connection with an ongoing investigation of the use of computer simulations for fault diagnosis training cites 61 published works taken predominantly from the disciplines of engineering, psychology, and education. A review of the existing literature included computer searches of the past ten years of…

Theoretical Aspects of the Patterns Recognition Statistical Theory Used for Developing the Diagnosis Algorithms for Complicated Technical Systems

Science.gov (United States)

Obozov, A. A.; Serpik, I. N.; Mihalchenko, G. S.; Fedyaeva, G. A.

2017-01-01

In the article, the problem of application of the pattern recognition (a relatively young area of engineering cybernetics) for analysis of complicated technical systems is examined. It is shown that the application of a statistical approach for hard distinguishable situations could be the most effective. The different recognition algorithms are based on Bayes approach, which estimates posteriori probabilities of a certain event and an assumed error. Application of the statistical approach to pattern recognition is possible for solving the problem of technical diagnosis complicated systems and particularly big powered marine diesel engines.

Correlated charge-changing uion-atom collisions. Final Technical Report

International Nuclear Information System (INIS)

John Tanis

2005-01-01

This document comprises the final technical report for atomic collisions research supported by DOE grant No. DE-FG02-87ER13778 from September 1, 2001 through August 31, 2004. The research involved the experimental investigation of excitation and charge-changing processes occurring in ion-atom and ion-molecule collisions. Major emphases of the study were: (1) interference effects resulting from coherent electron emission in H2, (2) production of doubly vacant K-shell (hollow ion) states due to electron correlation, and (3) formation of long-lived metastable states in electron transfer processes. During the period of the grant, this research resulted in 23 publications, 12 invited presentations, and 39 contributed presentations at national and international meetings and other institutions. Brief summaries of the completed research are presented below

FERMI(at)Elettra FEL Design Technical Optimization Final Report

International Nuclear Information System (INIS)

Fawley, William; Penn, Gregory; Allaria, Enrico; De Ninno, Giovanni; Graves, William

2006-01-01

This is the final report of the FEL Design Group for the Technical Optimization Study for the FERMI(at)ELETTRA project. The FERMI(at)ELETTRA project is based on the principle of harmonic upshifting of an initial ''seed'' signal in a single pass, FEL amplifier employing multiple undulators. There are a number of FEL physics principles which underlie this approach to obtaining short wavelength output: (1) the energy modulation of the electron beam via the resonant interaction with an external laser seed (2) the use of a chromatic dispersive section to then develop a strong density modulation with large harmonic overtones (3) the production of coherent radiation by the microbunched beam in a downstream radiator. Within the context of the FERMI project, we discuss each of these elements in turn

SIMS study on statistics and environmental factors in health. Final technical report to Department of Energy

International Nuclear Information System (INIS)

1982-07-01

This final technical report to DOE consists of five individual technical reports and one working paper by members of the SIMS Study at Stanford. Research topics include testing goodness-of-fit for the distribution of errors in regression models, mathematical models of cancer and their use in risk assessment, pollutant standards index (Psi), osteosarcomas among beagles exposed to 239 Plutonium, air pollution and respiratory disease, and models of human exposure to air pollution. Individual summaries of the six reports are indexed separately

Technical diagnosis system for EAST tokamak

International Nuclear Information System (INIS)

Qian Jing; Weng, P.D.; Luo, J.R.; Chen, Z.M.; Wu, Y.

2010-01-01

Technical diagnosis system (TDS) is one of the important subsystems of EAST (experimental advanced superconducting tokamak) device, main function of which is to monitor status parameters in EAST device. Those status parameters include temperature of different positions of main components, resistance of each superconducting (SC) coils, joint resistance of SC coils and high-temperature superconducting (HTS) current leads, strain of cold-quality components endured force, and displacement and current of toroidal field (TF) coils in EAST device, which are analog input signals. In addition there are still some analog and digital output signals. The TDS monitors all of those signals in the period of EAST experiments. TDS data monitoring is described in detail for it plays important role during EAST campaign. And how to protect the SC magnet system during each plasma discharging is presented with data of temperature of coolant inlet and outlet of SC coils and feeders and cases of the TF coils and temperature in the upper and middle and bottom of the TF coil case. During construction of the TDS primary difficulties come from installation of Lakeshore Cernox temperature sensors, strain measurement of central solenoid coils support legs and installation of co-wound voltage sensors for quench detection. While during operation since the first commissioning big challenges are from temperature measurement changes in current leads and quench detection of PF coils. Those difficulties in both stages are introduced which are key to make the TDS reliable. Meanwhile analysis of experimental data like temperature as a back up to testify quench occurrence and stress on vacuum vessel thermal shield and vacuum vessel have also been discussed.

Final Technical Report DOE/GO/13142-1

Energy Technology Data Exchange (ETDEWEB)

Patrick Mulvihill; Quang Nguyen

2010-09-15

This research adds to the understanding of the areas of residual starch and biomass conversion to alcohol, by providing data from pilot plant equipment of larger scale than the minimum required to give commercially scalable data. Instrumentation and control is in place to capture the information produced, for economic and technical evaluation. The impact of rheology, recycle streams, and residence time distributions on the technical and economic performance can be assessed. Various processes can be compared technically and economically because the pilot plants are readily modifiable. Several technologies for residual starch yield improvement have been identified, implemented, and patent applications filed. Various biomass-to-ethanol processes have been compared and one selected for technical optimization and commercialization. The technical and economic feasibility of the current simplified biomass conversion process is being confirmed by intensive pilot plant efforts as of this writing. Optimization of the feedstock handling and pretreatment is occurring to increase the alcohol yield above the minimum commercially viable level already demonstrated. Samples of biomass residue and reactor blowdown condensate are being collected to determine the technical and economic performance of the high-water-recycle waste treatment system being considered for the process. The project is of benefit to the public because it is advancing the efforts to achieve low-cost fermentable substrates for conversion to transportation fuels. This process combines the hydrolysis of agricultural residues with novel enzymes and organisms to convert the sugars released to transportation fuels. The process development is taking place at a scale allowing commercial development to proceed at a rapid pace.

Point-of-care diagnosis of periodontitis using saliva: technically feasible but still a challenge

Directory of Open Access Journals (Sweden)

Suk eJi

2015-09-01

Full Text Available Periodontitis is a chronic inflammation of the periodontium caused by persistent bacterial infection that leads to the breakdown of connective tissue and bone. Because the ability to reconstruct the periodontium is limited after alveolar bone loss, early diagnosis and intervention should be the primary goals of periodontal treatment. However, periodontitis often progresses without noticeable symptoms, and many patients do not seek professional dental care until the periodontal destruction progresses to the point of no return. Furthermore, the current diagnosis of periodontitis depends on time-consuming clinical measurements. Therefore, there is an unmet need for near-patient testing to diagnose periodontitis. Saliva is an optimal biological fluid to serve as a near-patient diagnostic tool for periodontitis. Recent developments in point-of-care (POC testing indicate that a diagnostic test for periodontitis using saliva is now technically feasible. A number of promising salivary biomarkers associated with periodontitis have been reported. A panel of optimal biomarkers must be carefully selected based on the pathogenesis of periodontitis. The biggest hurdle for the POC diagnosis of periodontitis using saliva may be the process of validation in a large, diverse patient population. Therefore, we propose the organization of an International Consortium for Biomarkers of Periodontitis, which will gather efforts to identify, select, and validate salivary biomarkers for the diagnosis of periodontitis.

DOE FINAL TECHNICAL REPORT RP

Energy Technology Data Exchange (ETDEWEB)

RUSS PETERMAN

2012-01-01

The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

Technical support document for the surface disposal of sewage sludge. Final report

International Nuclear Information System (INIS)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed

Technical support document for the surface disposal of sewage sludge. Final report

Energy Technology Data Exchange (ETDEWEB)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed.

Pre-Hospital Fast Positive Cases Identified by DFB Ambulance Paramedics – Final Clinical Diagnosis

LENUS (Irish Health Repository)

Feeney, A

2016-04-01

Ischaemic stroke clinical outcomes are improved by earlier treatment with intravenous thrombolysis. An existing pathway at the Mater University Hospital for assessment of suspected acute stroke in the Emergency Department was updated, aiming to shorten ‘door to needle time’. This study examines the final clinical diagnosis of Dublin Fire Brigade Ambulance Paramedic identified Face Arm Speech Test (FAST) positive patients presenting to the Emergency Department over a 7 month period. A retrospective analysis was carried out of 177 consecutive FAST positive patients presenting between March and November 2014. The final clinical diagnosis was acute stroke in 57.1% (n=101) of patients. Of these, 76 were ischaemic strokes of whom 56.5% (n=43) were thrombolysed. In the pre-hospital setting Ambulance Paramedics can identify, with reasonable accuracy, acute stroke using the FAST test. Over half of the ischaemic stroke patients presenting via this pathway can be treated with intravenous thrombolysis

Technical assistance contractor Management Plan. Final [report

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins & Beckwith Agra, Inc. (SHB Agra), and Geraghty & Miller, Inc. (G&M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC`s groundwater technical breadth and depth, so G&M was brought in to augment the team`s capabilities. The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC`s management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls.

Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

Energy Technology Data Exchange (ETDEWEB)

Kinney, Edward R. [University of Colorado, Boulder, CO

2014-09-12

This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

Technical Report - FINAL

Energy Technology Data Exchange (ETDEWEB)

Barbara Luke, Director, UNLV Engineering Geophysics Laboratory

2007-04-25

Improve understanding of the earthquake hazard in the Las Vegas Valley and to assess the state of preparedness of the area's population and structures for the next big earthquake. 1. Enhance the seismic monitoring network in the Las Vegas Valley 2. Improve understanding of deep basin structure through active-source seismic refraction and reflection testing 3. Improve understanding of dynamic response of shallow sediments through seismic testing and correlations with lithology 4. Develop credible earthquake scenarios by laboratory and field studies, literature review and analyses 5. Refine ground motion expectations around the Las Vegas Valley through simulations 6. Assess current building standards in light of improved understanding of hazards 7. Perform risk assessment for structures and infrastructures, with emphasis on lifelines and critical structures 8. Encourage and facilitate broad and open technical interchange regarding earthquake safety in southern Nevada and efforts to inform citizens of earthquake hazards and mitigation opportunities

An Approach to Developing Independent Learning and Non-Technical Skills Amongst Final Year Mining Engineering Students

Science.gov (United States)

Knobbs, C. G.; Grayson, D. J.

2012-01-01

There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called "soft" skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was…

Final Technical Report for SISGR: Ultrafast Molecular Scale Chemical Imaging

Energy Technology Data Exchange (ETDEWEB)

Hersam, Mark C. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Guest, Jeffrey R. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Guisinger, Nathan P. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Hla, Saw Wai [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Schatz, George C. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Seideman, Tamar [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Van Duyne, Richard P. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry

2017-04-10

The Northwestern-Argonne SISGR program utilized newly developed instrumentation and techniques including integrated ultra-high vacuum tip-enhanced Raman spectroscopy/scanning tunneling microscopy (UHV-TERS/STM) and surface-enhanced femtosecond stimulated Raman scattering (SE-FSRS) to advance the spatial and temporal resolution of chemical imaging for the study of photoinduced dynamics of molecules on plasmonically active surfaces. An accompanying theory program addressed modeling of charge transfer processes using constrained density functional theory (DFT) in addition to modeling of SE-FSRS, thereby providing a detailed description of the excited state dynamics. This interdisciplinary and highly collaborative research resulted in 62 publications with ~ 48% of them being co-authored by multiple SISGR team members. A summary of the scientific accomplishments from this SISGR program is provided in this final technical report.

DIMEC - Final Report

DEFF Research Database (Denmark)

Conrad, Finn

1997-01-01

Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF.......Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF....

Final Technical Report: Hydrogen Codes and Standards Outreach

Energy Technology Data Exchange (ETDEWEB)

Hall, Karen I.

2007-05-12

This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see metal hydride storage cartridges in operation, and view other hydrogen energy products.

Technical support document for land application of sewage sludge. Volume 1. Final report

International Nuclear Information System (INIS)

Jones, A.; Beyer, L.; Rookwood, M.; Pacenka, J.; Bergin, J.

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the land application of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in land applied sewage sludge. The management practices associated with land application are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through land application are discussed

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

Energy Technology Data Exchange (ETDEWEB)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

International Nuclear Information System (INIS)

Anderson, Scott; Baca, Georgina; O'Connor, Michael

2015-01-01

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

Energy Technology Data Exchange (ETDEWEB)

Anderson, Scott [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; Baca, Georgina [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; O' Connor, Michael [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company

2015-12-31

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement. Refs, figs, tabs

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

International Nuclear Information System (INIS)

1998-01-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement

Technical review of externalities issues. Final report

International Nuclear Information System (INIS)

Niemeyer, V.

1994-12-01

Externalities has become the catchword for a major experiment in electric utility regulation. Together with increased competition as a means for economic regulation, this experiment represents a potential revolution in how electric utilities are regulated. It is very important for utilities and policy makers to understand the technical issues and arguments driving the externality experiment. This Technical Review presents four papers covering topics in economics that may play important roles in this revolution. The four papers are: Economic Issues in the Application of Externalities to Electricity Resource Selection; Climate Change, the Marginal Cost of Carbon Dioxide Emissions and the Implications for Carbon Dioxide Emissions Adders; Positive Externalities and Benefits from Electricity; and Socioeconomic Effects of Externality Adders for Electric Utility Emissions

Technical study gas storage. Final report

International Nuclear Information System (INIS)

Borowka, J.; Moeller, A.; Zander, W.; Koischwitz, M.A.

2001-01-01

This study will answer the following questions: (a) For what uses was the storage facility designed and for what use is it currently applied? Provide an overview of the technical data per gas storage facility: for instance, what is its capacity, volume, start-up time, etc.; (b) How often has this facility been used during the past 10 years? With what purpose was the facility brought into operation at the time? How much gas was supplied at the time from the storage facility?; (c) Given the characteristics and the use of the storage facility during the past 10 years and projected gas consumption in the future, how will the storage facility be used in the future?; (d) Are there other uses for which the gas storage facility can be deployed, or can a single facility be deployed for numerous uses? What are the technical possibilities in such cases? Questions (a) and (b) are answered separately for every storage facility. Questions (c) and (d) in a single chapter each (Chapter 2 and 3). An overview of the relevant storage data relating to current use, use in the last 10 years and use in future is given in the Annex

78 FR 29239 - Final Priority; Technical Assistance To Improve State Data Capacity-National Technical Assistance...

Science.gov (United States)

2013-05-20

... Assistance To Improve State Data Capacity--National Technical Assistance Center To Improve State Capacity To... Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State... (FY) 2013 and later years. We take this action to focus attention on an identified national need to...

[Investigation report on the technical standards of TCM diagnosis, treatment and rehabilitation equipment].

Science.gov (United States)

Shen, Hua; Liu, Tangyi; Yang, Huayuan

2016-02-01

The questionnaire was adopted so as to investigate the attitudes and recognition of the manufacture eneprises of TCM diagnosis, treatment and rehabilitation equipment (DTRE) to the technical standards of, relevant products. It was found that the construction of the industrial standard and the national standard was lagged behind on TCM DTRE. Under the new situation, the enterprises are highly willing to participate in the development of the industrial, national and international standards and have a certain of understanding on the standard development. Nearly 80 % of enterprises believed that it was necessary to set up the relevant mirror organization for the development of industrial, national and international standard of TCM DITRE. In the future, the standard construction of TCM DTRE must face to the new situation. The constant increasing of the enterprises. and scientific research organizations in the standard construction must promote the development of TCM DTRE.

Writing a technical note.

Science.gov (United States)

Ng, K H; Peh, W C G

2010-02-01

A technical note is a short article giving a brief description of a specific development, technique or procedure, or it may describe a modification of an existing technique, procedure or device applicable to medicine. The technique, procedure or device described should have practical value and should contribute to clinical diagnosis or management. It could also present a software tool, or an experimental or computational method. Technical notes are variously referred to as technical innovations or technical developments. The main criteria for publication will be the novelty of concepts involved, the validity of the technique and its potential for clinical applications.

Final waste classification and waste form technical position papers

International Nuclear Information System (INIS)

1983-05-01

The waste classification technical position paper describes overall procedures acceptable to NRC staff which may be used by licensees to determine the presence and concentrations of the radionuclides listed in section 61.55, and thereby classifying waste for near-surface disposal. This technical position paper also provides guidance on the types of information which should be included in shipment manifests accompanying waste shipments to near-surface disposal facilities. The technical position paper on waste form provides guidance to waste generators on test methods and results acceptable to NRC staff for implementing the 10 CFR Part 61 waste form requirements. It can be used as an acceptable approach for demonstrating compliance with the 10 CFR Part 61 waste structural stability criteria. This technical position paper includes guidance on processing waste into an acceptable stable form, designing acceptable high-integrity containers, packaging cartridge filters, and minimizing radiation effects on organic ion-exchange resins. The guidance in the waste form technical position paper may be used by licensees as the basis for qualifying process control programs to meet the waste form stability requirements, including tests which can be used to demonstrate resistance to degradation arising from the effects of compression, moisture, microbial activity, radiation, and chemical changes. Generic test data (e.g., topical reports prepared by vendors who market solidification technology) may be used for process control program qualification where such generic data is applicable to the particular types of waste generated by a licensee

Value of comprehensive renal ultrasound in children with acute urinary tract infection for assessment of renal involvement: comparison with DMSA scintigraphy and final diagnosis

Energy Technology Data Exchange (ETDEWEB)

Brader, Peter; Riccabona, Michael [Medical University Graz, Division of Pediatric Radiology, Department of Radiology, Graz (Austria); Schwarz, Thomas [Medical University Graz, Division of Nuclear Medicine, Department of Radiology, Graz (Austria); Seebacher, Ursula [Medical University Graz, Department of Pediatric Surgery, Graz (Austria); Ring, Ekkehard [Medical University Graz, Department of Pediatrics, Graz (Austria)

2008-12-15

The aim of this study was to evaluate the value of comprehensive renal ultrasound (US), i.e., combining greyscale US and amplitude-coded color Doppler sonography (aCDS), for assessment of urinary tract infection (UTI) in infants and children, compared to (1) {sup 99m}Tc DMSA scintigraphy and (2) final diagnosis. Two hundred eighty-seven children with UTI underwent renal comprehensive US and DMSA scintigraphy. The results were compared with regard to their reliability to diagnose renal involvement, using (1) DMSA scintigraphy and (2) final diagnosis as the gold standard. Sixty-seven children clinically had renal involvement. Sensitivity increased from 84.1% using only aCDS to 92.1% for the combined US approach, using DMSA scintigraphy as the reference standard. When correlated with the final diagnosis, sensitivity for DMSA scintigraphy was 92.5%; sensitivity for comprehensive US was 94.0%. Our data demonstrate an increasing sensitivity using the combination of renal greyscale US supplemented by aCDS for differentiation of upper from lower UTI. Sensitivity for DMSA and comprehensive US was similar for both methods compared to the final diagnosis. Comprehensive US should gain a more important role in the imaging algorithm of children with acute UTI, thereby reducing the radiation burden. (orig.)

Value of comprehensive renal ultrasound in children with acute urinary tract infection for assessment of renal involvement: comparison with DMSA scintigraphy and final diagnosis

International Nuclear Information System (INIS)

Brader, Peter; Riccabona, Michael; Schwarz, Thomas; Seebacher, Ursula; Ring, Ekkehard

2008-01-01

The aim of this study was to evaluate the value of comprehensive renal ultrasound (US), i.e., combining greyscale US and amplitude-coded color Doppler sonography (aCDS), for assessment of urinary tract infection (UTI) in infants and children, compared to (1) 99m Tc DMSA scintigraphy and (2) final diagnosis. Two hundred eighty-seven children with UTI underwent renal comprehensive US and DMSA scintigraphy. The results were compared with regard to their reliability to diagnose renal involvement, using (1) DMSA scintigraphy and (2) final diagnosis as the gold standard. Sixty-seven children clinically had renal involvement. Sensitivity increased from 84.1% using only aCDS to 92.1% for the combined US approach, using DMSA scintigraphy as the reference standard. When correlated with the final diagnosis, sensitivity for DMSA scintigraphy was 92.5%; sensitivity for comprehensive US was 94.0%. Our data demonstrate an increasing sensitivity using the combination of renal greyscale US supplemented by aCDS for differentiation of upper from lower UTI. Sensitivity for DMSA and comprehensive US was similar for both methods compared to the final diagnosis. Comprehensive US should gain a more important role in the imaging algorithm of children with acute UTI, thereby reducing the radiation burden. (orig.)

Alumina reinforced tetragonal zirconia (TZP) composites. Final technical report, July 1, 1993--December 31, 1996

International Nuclear Information System (INIS)

Shetty, D.K.

1997-01-01

This final technical report summarizes the significant research results obtained during the period July 1, 1993 through December 31, 1996 in the DOE-supported research project entitled, open-quotes Alumina Reinforced Tetragonal Zirconia (TZP) Compositesclose quotes. The objective of the research was to develop high-strength and high-toughness ceramic composites by combining mechanisms of platelet, whisker or fiber reinforcement with transformation toughening. The approach used included reinforcement of Celia- or yttria-partially-stabilized zirconia (Ce-TZP or Y-TZP) with particulates, platelets, or continuous filaments of alumina

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Velasco, Mayda [Northwestern University

2013-11-01

This work is focused on the design and construction of novel beam diagnostic and instrumentation for charged particle accelerators required for the next generation of linear colliders. Our main interest is in non-invasive techniques. The Northwestern group of Velasco has been a member of the CLIC Test Facility 3 (CTF3) collaboration since 2003, and the beam instrumentation work is developed mostly at this facility1. This 4 kW electron beam facility has a 25-170 MeV electron LINAC. CTF3 performed a set of dedicated measurements to finalize the development of our RF-Pickup bunch length detectors. The RF-pickup based on mixers was fully commissioned in 2009 and the RF-pickup based on diodes was finished in time for the 2010-11 data taking. The analysis of all the data taken in by the summer of 2010 was finish in time and presented at the main conference of the year, LINAC 2010 in Japan.

State child health; revisions to the regulations implementing the State Children's Health Insurance Program. Interim final rule with comment period; revisions, delay of effective date, and technical amendments to final rule.

Science.gov (United States)

2001-06-25

Title XXI authorizes the State Children's Health Insurance Program (SCHIP) to assist State efforts to initiate and expand the provision of child health assistance to uninsured, low-income children. On January 11, 2001 we published a final rule in the Federal Register to implement SCHIP that has not gone into effect. This interim final rule further delays the effective date, revises certain provisions and solicits public comment, and makes technical corrections and clarifications to the January 2001 final rule based on further review of the comments received and applicable law. Only the provisions set forth in this document have changed. All other provisions set forth in the January 2001 final rule will be implemented without change.

Final priority. Rehabilitation Training: Job-Driven Vocational Rehabilitation Technical Assistance Center. Final priority.

Science.gov (United States)

2014-08-19

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Rehabilitation Training program to establish a Job-Driven Vocational Rehabilitation Technical Assistance Center (JDVRTAC). The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to focus on training in an area of national need. Specifically, this priority responds to the Presidential Memorandum to Federal agencies directing them to take action to address job-driven training for the Nation's workers. The JDVRTAC will provide technical assistance (TA) to State vocational rehabilitation (VR) agencies to help them develop for individuals with disabilities training and employment opportunities that meet the needs of today's employers.

Final priority; Technical Assistance on State Data Collection--IDEA Data Management Center. Final priority.

Science.gov (United States)

2014-08-05

The Assistant Secretary for the Office of Special Education and Rehabilitative Services (OSERS) announces a priority under the Technical Assistance on State Data Collection program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to fund a cooperative agreement to establish and operate an IDEA Data Management Center (Center) that will provide technical assistance (TA) to improve the capacity of States to meet the data collection requirements of the Individuals with Disabilities Education Act (IDEA).

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Saurwein, John

2011-07-15

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

International Nuclear Information System (INIS)

Saurwein, J.

2011-01-01

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

Imagining Technicities

DEFF Research Database (Denmark)

Liboriussen, Bjarke; Plesner, Ursula

2011-01-01

to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

International Nuclear Information System (INIS)

Vierow, Karen; Aldemir, Tunc

2009-01-01

The project entitled, 'Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors', was conducted as a DOE NERI project collaboration between Texas A and M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Vierow, Karen; Aldemir, Tunc

2009-09-10

The project entitled, “Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors”, was conducted as a DOE NERI project collaboration between Texas A&M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Programs of Study as a State Policy Mandate: A Longitudinal Study of the South Carolina Personal Pathways to Success Initiative. Final Technical Report: Major Findings and Implications

Science.gov (United States)

Hammond, Cathy; Drew, Sam F.; Withington, Cairen; Griffith, Cathy; Swiger, Caroline M.; Mobley, Catherine; Sharp, Julia L.; Stringfield, Samuel C.; Stipanovic, Natalie; Daugherty, Lindsay

2013-01-01

This is the final technical report from the National Research Center for Career and Technical Education's (NRCCTE's) five-year longitudinal study of South Carolina's Personal Pathway to Success initiative, which was authorized by the state's Education and Economic Development Act (EEDA) in 2005. NRCCTE-affiliated researchers at the National…

Final Technical Report - Kotzebue Wind Power Project - Volume II

Energy Technology Data Exchange (ETDEWEB)

Rana Zucchi, Global Energy Concepts, LLC; Brad Reeve, Kotzebue Electric Association; DOE Project Officer - Doug Hooker

2007-10-31

The Kotzebue Wind Power Project is a joint undertaking of the U.S. Department of Energy (DOE); Kotzebue Electric Association (KEA); and the Alaska Energy Authority (AEA). The goal of the project is to develop, construct, and operate a wind power plant interconnected to a small isolated utility grid in an arctic climate in Northwest Alaska. The primary objective of KEA’s wind energy program is to bring more affordable electricity and jobs to remote Alaskan communities. DOE funding has allowed KEA to develop a multi-faceted approach to meet these objectives that includes wind project planning and development, technology transfer, and community outreach. The first wind turbines were installed in the summer of 1997 and the newest turbines were installed in the spring of 2007. The total installed capacity of the KEA wind power project is 1.16 MW with a total of 17 turbines rated between 65 kW and 100 kW. The operation of the wind power plant has resulted in a wind penetration on the utility system in excess of 35% during periods of low loads. This document and referenced attachments are presented as the final technical report for the U.S. Department of Energy (DOE) grant agreement DE-FG36-97GO10199. Interim deliverables previously submitted are also referenced within this document and where reasonable to do so, specific sections are incorporated in the report or attached as appendices.

Energy-related inventions program invention 637. Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-31

The final technical report for the Pegasus plow, a stalk and root embedding apparatus, describes progress from the development stage to the product support stage. The US Department of Agriculture - Agriculture Research Service (ARS) is now in the second year of a three year study comparing the Pegasus to conventional tillage. So far, no downside has been with the Pegasus and the following benefits have been documented: (1) Energy savings of 65.0 kilowatt hours per hectare over conventional tillage. This is when the Pegasus plow is used to bury whole stalks, and represents a 70% savings over conventional tillage (92.5 kilowatt hours per hectare). (2) Four to seven fewer passes of tillage, depending on the particular situation. This represents a substantial time savings to farmers. (3) So far, no differences in cotton yields. Recent cotton boll counts in one study indicate a higher yield potential with the Pegasus. (4) No disease problems. (5) Significantly higher levels of organic matter in the soil. A hypothesis of the study is that whole stalk burial may reduce plant disease problems. This hypothesis has not yet been proven. (6) Significantly higher levels of nitrate nitrogen. Total nitrogen and ammonia nitrogen trended higher but were not significantly different. This shows that whole stalk burial does not adversely affect the nitrogen cycle in the soil and may actually improve it. The marketing support stage of the project is also described in the report.

A Framework for Final Drive Simultaneous Failure Diagnosis Based on Fuzzy Entropy and Sparse Bayesian Extreme Learning Machine

Directory of Open Access Journals (Sweden)

Qing Ye

2015-01-01

Full Text Available This research proposes a novel framework of final drive simultaneous failure diagnosis containing feature extraction, training paired diagnostic models, generating decision threshold, and recognizing simultaneous failure modes. In feature extraction module, adopt wavelet package transform and fuzzy entropy to reduce noise interference and extract representative features of failure mode. Use single failure sample to construct probability classifiers based on paired sparse Bayesian extreme learning machine which is trained only by single failure modes and have high generalization and sparsity of sparse Bayesian learning approach. To generate optimal decision threshold which can convert probability output obtained from classifiers into final simultaneous failure modes, this research proposes using samples containing both single and simultaneous failure modes and Grid search method which is superior to traditional techniques in global optimization. Compared with other frequently used diagnostic approaches based on support vector machine and probability neural networks, experiment results based on F1-measure value verify that the diagnostic accuracy and efficiency of the proposed framework which are crucial for simultaneous failure diagnosis are superior to the existing approach.

Screening and preventive diagnosis with radiological imaging

Energy Technology Data Exchange (ETDEWEB)

Reiser, M.F. [University Hospitals - Grosshadern and Innenstadt (Germany). Dept. of Clinical Radiology; Kaick, G. van [Deutsches Krebsforschungszentrum, Heidelberg (Germany); Fink, C.; Schoenberg, S.O. (eds.) [Univ. Hospital Mannheim (Germany). Dept. of Clinical Radiology

2008-07-01

Continuous technical developments have improved the potential of organ-based radiological diagnostics and have now also led to the use of dedicated whole-body examinations in the field of screening and preventive diagnosis. This book aims to provide clinicians with a broad understanding of screening and preventive diagnosis using radiological imaging. The first part of the book is dedicated to the fundamentals of screening and preventive diagnosis, and comprises chapters on epidemiology and pathology, technical and organizational aspects of radiological screening, legal and ethical issues, and cost-benefit analysis. The second part of the book discusses in depth the most important practical examples of radiological screening and surveillance, both for unselected populations and for individual risk groups. (orig.)

Screening and preventive diagnosis with radiological imaging

International Nuclear Information System (INIS)

Reiser, M.F.; Fink, C.; Schoenberg, S.O.

2008-01-01

Continuous technical developments have improved the potential of organ-based radiological diagnostics and have now also led to the use of dedicated whole-body examinations in the field of screening and preventive diagnosis. This book aims to provide clinicians with a broad understanding of screening and preventive diagnosis using radiological imaging. The first part of the book is dedicated to the fundamentals of screening and preventive diagnosis, and comprises chapters on epidemiology and pathology, technical and organizational aspects of radiological screening, legal and ethical issues, and cost-benefit analysis. The second part of the book discusses in depth the most important practical examples of radiological screening and surveillance, both for unselected populations and for individual risk groups. (orig.)

Technical considerations associated with spent fuel acceptance. Final report

International Nuclear Information System (INIS)

Supko, E.M.

1996-06-01

This study was initiated by the Electric Power Research Institute (EPRI) to identify technical considerations associated with spent fuel acceptance and implementation of a waste management system that includes the use of transportable storage systems, and to serve as an opening dialogue among Standard Contract Holders and the department of Energy's Office of Civilian Radioactive Waste management (OCRWM) prior to the development of waste acceptance criteria or issuance of a Notice of Proposed Rulemaking by OCRWM to amend the Standard Contract. The original purpose of the Notice of Proposed Rulemaking was to address changes to the Standard Contract to implement a multi-purpose canister based system and to address other issues that were not adequately addressed in the standard contract. Even if DOE does not develop a multi-purpose canister based system for waste acceptance, it will still be necessary to develop waste acceptance criteria in order to accept spent fuel in transportable storage systems that are being deployed for at-reactor storage. In this study, technical issues associated with spent fuel acceptance will be defined and potential options and alternatives for resolution of technical considerations will be explored

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Held, Isaac [Princeton Univ., NJ (United States); Balaji, V. [Princeton Univ., NJ (United States); Fueglistaler, Stephan [Princeton Univ., NJ (United States)

2016-09-19

We have constructed and analyzed a series of idealized models of tropical convection interacting with large-scale circulations, with 25-50km resolution and with 1-2km cloud resolving resolution to set the stage for rigorous tests of convection closure schemes in high resolution global climate models. Much of the focus has been on the climatology of tropical cyclogenesis in rotating systems and the related problem of the spontaneous aggregation of convection in non-rotating systems. The PI (Held) will be delivering the honorary Bjerknes lecture at the Fall 2016 AGU meeting in December on this work. We have also provided new analyses of long-standing issues related to the interaction between convection and the large-scale circulation: Kelvin waves in the upper troposphere and lower stratosphere, water vapor transport into the stratosphere, and upper tropospheric temperature trends. The results of these analyses help to improve our understanding of processes, and provide tests for future high resolution global modeling. Our final goal of testing new convections schemes in next-generation global atmospheric models at GFDL has been left for future work due to the complexity of the idealized model results meant as tests for these models uncovered in this work and to computational resource limitations. 11 papers have been published with support from this grant, 2 are in review, and another major summary paper is in preparation.

Final technical report; Mercury Release from Organic matter (OM) and OM-Coated Mineral Surfaces

Energy Technology Data Exchange (ETDEWEB)

Aiken, George

2014-10-02

This document is the final technical report for a project designed to address fundamental processes controlling the release of mercury from flood plain soils associated with East Fork Poplar Creek, Tennessee near the U.S. Department of Energy Oak Ridge facility. The report summarizes the activities, findings, presentations, and publications resulting from an award to the U.S. Geological that were part of a larger overall effort including Kathy Nagy (University of Illinois, Chicago, Ill) and Joseph Ryan (University of Colorado, Boulder, CO). The specific charge for the U.S.G.S. portion of the study was to provide analytical support for the larger group effort (Nagy and Ryan), especially with regard to analyses of Hg and dissolved organic matter, and to provide information about the release of mercury from the floodplain soils.

Microscopic heavy-ion theory. Final technical report, June 1, 1993 - May 31, 1996

International Nuclear Information System (INIS)

Ernst, D.J.; Oberacker, V.E.; Umar, A.S.

1998-01-01

In this Final Technical Report, the authors summarize the research activities of the three Principal Investigators (Professors Ernst, Oberacker, and Umar) at Vanderbilt University since the last reporting period through the subject award expiration date (Dec. 31, 1996) under contract DE-FG05-87ER40376 with the Department of Energy. The research effort is divided between the following three areas: nuclear structure and astrophysics (microscopic nuclear structure studies and properties of exotic nuclei at HRIBF, supernovae calculations in connection with nuclear astrophysics, and nuclear viscosity studies via muon-induced fission at PSI); pion and kaon interactions with the nucleus at high energies (interaction of pions and kaons with nuclei from low energies to 1 GeV, propagation of excited hadrons in the nuclear medium as probed by pion and electron induced reactions); nuclear physics at high energies (dynamical string-parton model to study multi-particle production at RHIC, electromagnetic lepton pair production at RHIC)

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

In-Vivo Proton Magnetic Resonance Spectroscopy of 2-Hydroxyglutarate in Isocitrate Dehydrogenase-Mutated Gliomas: A Technical Review for Neuroradiologists

International Nuclear Information System (INIS)

Kim, Hyeonjin; Kim, Sungjin; Lee, Hyeong Hun; Heo, Hwon

2016-01-01

The diagnostic and prognostic potential of an onco-metabolite, 2-hydroxyglutarate (2HG) as a proton magnetic resonance spectroscopy (1H-MRS) detectable biomarker of the isocitrate dehydrogenase (IDH)-mutated (IDH-MT) gliomas has drawn attention of neuroradiologists recently. However, due to severe spectral overlap with background signals, quantification of 2HG can be very challenging. In this technical review for neuroradiologists, first, the biochemistry of 2HG and its significance in the diagnosis of IDH-MT gliomas are summarized. Secondly, various 1H-MRS methods used in the previous studies are outlined. Finally, wereview previous in vivo studies, and discuss the current status of 1H-MRS in the diagnosis of IDH-MT gliomas

In-Vivo Proton Magnetic Resonance Spectroscopy of 2-Hydroxyglutarate in Isocitrate Dehydrogenase-Mutated Gliomas: A Technical Review for Neuroradiologists

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyeonjin [Department of Radiology, Seoul National University Hospital, Seoul 03080 (Korea, Republic of); Department of Biomedical Sciences, Seoul National University, Seoul 03087 (Korea, Republic of); Institute of Radiation Medicine, Seoul National University Medical Research Center, Seoul 03080 (Korea, Republic of); Kim, Sungjin [Department of Radiology, Seoul National University Hospital, Seoul 03080 (Korea, Republic of); Lee, Hyeong Hun; Heo, Hwon [Department of Biomedical Sciences, Seoul National University, Seoul 03087 (Korea, Republic of)

2016-11-01

The diagnostic and prognostic potential of an onco-metabolite, 2-hydroxyglutarate (2HG) as a proton magnetic resonance spectroscopy (1H-MRS) detectable biomarker of the isocitrate dehydrogenase (IDH)-mutated (IDH-MT) gliomas has drawn attention of neuroradiologists recently. However, due to severe spectral overlap with background signals, quantification of 2HG can be very challenging. In this technical review for neuroradiologists, first, the biochemistry of 2HG and its significance in the diagnosis of IDH-MT gliomas are summarized. Secondly, various 1H-MRS methods used in the previous studies are outlined. Finally, wereview previous in vivo studies, and discuss the current status of 1H-MRS in the diagnosis of IDH-MT gliomas.

Technical advisory panel for the large acceptance spectrometer: Final report

International Nuclear Information System (INIS)

1989-01-01

The Technical Advisory Panel for the Large Acceptance Spectrometer met on November 17--19, 1988, at CEBAF to perform a second review of the status of this project. The charge to the Panel was ''to provide technical advice to the CEBAF directorate on the design, construction, cost, schedule, and implementation of the Large Acceptance Spectrometer.'' In this written report, an overview of the entire project is given. Specific comments on the major components, data handling and analysis, assembly and installation, and management are presented. The Panel's conclusions are contained in the Executive Summary at the beginning of the report

Health condition and residual life of deteriorating technical systems

Energy Technology Data Exchange (ETDEWEB)

Reinertsen, Rune

1998-12-31

Many offshore installations in the Norwegian Sector of the North Sea approach the end of their useful life. The same is true of many power plants and technical systems in general. This thesis describes the theory and improves the methods for the determination of the health condition and residual life of technical systems. Rather than developing new methods it discusses new ways of using existing statistical methods. The main contributions are: (1) A survey of the literature of diagnosis, prediction and life extension for deteriorating technical systems, (2) A discussion of some consequences of selecting the wrong life model, (3) A description of problems related to the determination of mean residual life of non-repairable technical systems, (4) Presentation of the concept of `technical health` to describe the soundness of a system exposed to failure mechanisms, (5) A model for predicting the technical health and residual life of a corroding system, (6) Recommends requirements and methods for using expert knowledge in safety and reliability analysis, (7) A general inspection strategy for system fault diagnosis by using Shannon entropy, (8) Points out weaknesses and strengths of risk measures used in the offshore industry today. 237 refs., 23 figs., 6 tabs.

Health condition and residual life of deteriorating technical systems

Energy Technology Data Exchange (ETDEWEB)

Reinertsen, Rune

1997-12-31

Many offshore installations in the Norwegian Sector of the North Sea approach the end of their useful life. The same is true of many power plants and technical systems in general. This thesis describes the theory and improves the methods for the determination of the health condition and residual life of technical systems. Rather than developing new methods it discusses new ways of using existing statistical methods. The main contributions are: (1) A survey of the literature of diagnosis, prediction and life extension for deteriorating technical systems, (2) A discussion of some consequences of selecting the wrong life model, (3) A description of problems related to the determination of mean residual life of non-repairable technical systems, (4) Presentation of the concept of `technical health` to describe the soundness of a system exposed to failure mechanisms, (5) A model for predicting the technical health and residual life of a corroding system, (6) Recommends requirements and methods for using expert knowledge in safety and reliability analysis, (7) A general inspection strategy for system fault diagnosis by using Shannon entropy, (8) Points out weaknesses and strengths of risk measures used in the offshore industry today. 237 refs., 23 figs., 6 tabs.

System-Cost-Optimized Smart EVSE for Residential Application: Final Technical Report including Manufacturing Plan

Energy Technology Data Exchange (ETDEWEB)

Zhu, Charles [Delta Products, Triangle Park, NC (United States)

2015-05-15

In the 2nd quarter of 2012, a program was formally initiated at Delta Products to develop smart-grid-enabled Electric Vehicle Supply Equipment (EVSE) product for residential use. The project was funded in part by the U.S. Department of Energy (DOE), under award DE-OE0000590. Delta products was the prime contractor to DOE during the three year duration of the project. In addition to Delta Products, several additional supplier-partners were engaged in this research and development (R&D) program, including Detroit Edison DTE, Mercedes Benz Research and Development North America, and kVA. This report summarizes the program and describes the key research outcomes of the program. A technical history of the project activities is provided, which describes the key steps taken in the research and the findings made at successive stages in the multi-stage work. The evolution of an EVSE prototype system is described in detail, culminating in prototypes shipped to Department of Energy Laboratories for final qualification. After the program history is reviewed, the key attributes of the resulting EVSE are described in terms of functionality, performance, and cost. The results clearly demonstrate the ability of this EVSE to meet or exceed DOE's targets for this program, including: construction of a working product-intent prototype of a smart-grid-enabled EVSE, with suitable connectivity to grid management and home-energy management systems, revenue-grade metering, and related technical functions; and cost reduction of 50% or more compared to typical market priced EVSEs at the time of DOE's funding opportunity announcement (FOA), which was released in mid 2011. In addition to meeting all the program goals, the program was completed within the original budget and timeline established at the time of the award. The summary program budget and timeline, comparing plan versus actual values, is provided for reference, along with several supporting explanatory notes. Technical

Microcomputer Intelligence for Technical Training (MITT): The evolution of an intelligent tutoring system

Science.gov (United States)

Norton, Jeffrey E.; Wiederholt, Bradley J.; Johnson, William B.

1990-01-01

Microcomputer Intelligence for Technical Training (MITT) uses Intelligent Tutoring System (OTS) technology to deliver diagnostic training in a variety of complex technical domains. Over the past six years, MITT technology has been used to develop training systems for nuclear power plant diesel generator diagnosis, Space Shuttle fuel cell diagnosis, and message processing diagnosis for the Minuteman missile. Presented here is an overview of the MITT system, describing the evolution of the MITT software and the benefits of using the MITT system.

Technical democracy as a challenge to urban studies

DEFF Research Database (Denmark)

Farías, Ignacio; Blok, Anders

2016-01-01

What is technical democracy? And why does it matter for urban studies? As an introduction to this special feature, we address these questions by reflecting on To Our Friends, the 2014 manifesto of the Invisible Committee. We engage in particular its provocative diagnosis of the current situation......: power no longer resides in the modern institutions of representative democracy and the market economy; instead, power has become a matter of logistics, infrastructures and expertise. This diagnosis, we suggest, brings into view the challenge of technical democracy, that is, the democratization of techno......-scientific expertise and the instauration of forms of lasting collaboration among experts and laypeople. Urban politics, we claim, increasingly turns around socio-technical controversies and it is in terms of the politics of expertise that we should analyse and engage it. Building on Science and Technology Studies...

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

International Nuclear Information System (INIS)

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff's review of Atlas Corporation's proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs

Final Technical Report - SciDAC Cooperative Agreement: Center for Extended Magnetohydrodynamic Modeling/ Transport and Dynamics in Torodial Fusion System

International Nuclear Information System (INIS)

Schanck, Dalton D.

2010-01-01

Final technical report for research performed by Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Extended MHD Modeling, DE-FC02-06ER54870, for the period 7/1/06 to 2/15/08. Principal results for this period are: 1. Development of a model for computational modeling for the primitive form of the extended MMD equations. This was reported as Phys. Plasmas 13, 058103 (2006). 2. Comparison between the NIMROD and M3D codes for simulation of the nonlinear sawtooth crash in the CDXU tokamak. This was reported in Phys. Plasmas 14, 056105 (2006). 3. Demonstration of 2-fluid and gyroviscous stabilization of interchange modes using computational extended MHD models. This was reported in Phys. Rev. Letters 101, 085005 (2008). Each of these publications is attached as an Appendix of this report. They should be consulted for technical details.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1--December 31, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin`s Building 100 facility in Valley Forge, PA, which is detailed in Part B.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1-December 31, 1998

International Nuclear Information System (INIS)

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin's Building 100 facility in Valley Forge, PA, which is detailed in Part B

Modular Radioisotope Thermoelectric Generator (RTG) Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

1992-12-31

Section 2.0 of this report summarizes the MOD-RTG reference flight design, and Section 3.0 discusses the Ground Demonstration System design. Multicouple technology development is discussed in Section 4.0, and Section 5.0 lists all published technical papers prepared during the course of the contract.

Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

International Nuclear Information System (INIS)

Chicken, J.C.

1988-01-01

This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

[Definition of the Diagnosis Osteomyelitis-Osteomyelitis Diagnosis Score (ODS)].

Science.gov (United States)

Schmidt, H G K; Tiemann, A H; Braunschweig, R; Diefenbeck, M; Bühler, M; Abitzsch, D; Haustedt, N; Walter, G; Schoop, R; Heppert, V; Hofmann, G O; Glombitza, M; Grimme, C; Gerlach, U-J; Flesch, I

2011-08-01

The disease "osteomyelitis" is characterised by different symptoms and parameters. Decisive roles in the development of the disease are played by the causative bacteria, the route of infection and the individual defense mechanisms of the host. The diagnosis is based on different symptoms and findings from the clinical history, clinical symptoms, laboratory results, diagnostic imaging, microbiological and histopathological analyses. While different osteomyelitis classifications have been published, there is to the best of our knowledge no score that gives information how sure the diagnosis "osteomyelitis" is in general. For any scientific study of a disease a valid definition is essential. We have developed a special osteomyelitis diagnosis score for the reliable classification of clinical, laboratory and technical findings. The score is based on five diagnostic procedures: 1) clinical history and risk factors, 2) clinical examination and laboratory results, 3) diagnostic imaging (ultrasound, radiology, CT, MRI, nuclear medicine and hybrid methods), 4) microbiology, and 5) histopathology. Each diagnostic procedure is related to many individual findings, which are weighted by a score system, in order to achieve a relevant value for each assessment. If the sum of the five diagnostic criteria is 18 or more points, the diagnosis of osteomyelitis can be viewed as "safe" (diagnosis class A). Between 8-17 points the diagnosis is "probable" (diagnosis class B). Less than 8 points means that the diagnosis is "possible, but unlikely" (class C diagnosis). Since each parameter can score six points at a maximum, a reliable diagnosis can only be achieved if at least 3 parameters are scored with 6 points. The osteomyelitis diagnosis score should help to avoid the false description of a clinical presentation as "osteomyelitis". A safe diagnosis is essential for the aetiology, treatment and outcome studies of osteomyelitis. © Georg Thieme Verlag KG Stuttgart · New York.

Application of the ecosystem diagnosis and treatment method to the Grande Ronde Model Watershed project. Final report

International Nuclear Information System (INIS)

Mobrand, L.; Lestelle, L.

1997-01-01

In the spring of 1994 a technical planning support project was initiated by the Grande Ronde Model Watershed Board of Directors (Board) with funding from the Bonneville Power Administration. The project was motivated by a need for a science based method for prioritizing restoration actions in the basin that would promote effectiveness and accountability. In this section the authors recall the premises for the project. The authors also present a set of recommendations for implementing a watershed planning process that incorporates a science-based framework to help guide decision making. This process is intended to assist the Grande Ronde Model Watershed Board in its effort to plan and implement watershed improvement measures. The process would also assist the Board in coordinating its efforts with other entities in the region. The planning process is based on an approach for developing an ecosystem management strategy referred to as the Ecosystem Diagnosis and Treatment (EDT) method (Lichatowich et al. 1995, Lestelle et al. 1996). The process consists of an on-going planning cycle. Included in this cycle is an assessment of the ability of the watershed to support and sustain natural resources and other economic and societal values. This step in the process, which the authors refer to as the diagnosis, helps guide the development of actions (also referred to as treatments) aimed at improving the conditions of the watershed to achieve long-term objectives. The planning cycle calls for routinely reviewing and updating, as necessary, the basis for the diagnosis and other analyses used by the Board in adopting actions for implementation. The recommendations offered here address this critical need to habitually update the information used in setting priorities for action

Application of the Ecosystem Diagnosis and Treatment Method to the Grande Ronde Model Watershed project : Final Report.

Energy Technology Data Exchange (ETDEWEB)

Mobrand, Lars Erik; Lestelle, Lawrence C.

1997-01-01

In the spring of 1994 a technical planning support project was initiated by the Grande Ronde Model Watershed Board of Directors (Board) with funding from the Bonneville Power Administration. The project was motivated by a need for a science based method for prioritizing restoration actions in the basin that would promote effectiveness and accountability. In this section the authors recall the premises for the project. The authors also present a set of recommendations for implementing a watershed planning process that incorporates a science-based framework to help guide decision making. This process is intended to assist the Grande Ronde Model Watershed Board in its effort to plan and implement watershed improvement measures. The process would also assist the Board in coordinating its efforts with other entities in the region. The planning process is based on an approach for developing an ecosystem management strategy referred to as the Ecosystem Diagnosis and Treatment (EDT) method (Lichatowich et al. 1995, Lestelle et al. 1996). The process consists of an on-going planning cycle. Included in this cycle is an assessment of the ability of the watershed to support and sustain natural resources and other economic and societal values. This step in the process, which the authors refer to as the diagnosis, helps guide the development of actions (also referred to as treatments) aimed at improving the conditions of the watershed to achieve long-term objectives. The planning cycle calls for routinely reviewing and updating, as necessary, the basis for the diagnosis and other analyses used by the Board in adopting actions for implementation. The recommendations offered here address this critical need to habitually update the information used in setting priorities for action.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Howe, Gary [RTI International, Research Triangle Park, NC (United States); Albritton, John [RTI International, Research Triangle Park, NC (United States); Denton, David [RTI International, Research Triangle Park, NC (United States); Turk, Brian [RTI International, Research Triangle Park, NC (United States); Gupta, Raghubir [RTI International, Research Triangle Park, NC (United States)

2018-01-31

technology has great potential to provide clean syngas from coal and petcoke-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.

NetView technical research

Science.gov (United States)

1993-01-01

This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff`s review of Atlas Corporation`s proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs.

Final priority; technical assistance to improve state data capacity--National Technical Assistance Center to improve state capacity to accurately collect and report IDEA data. Final priority.

Science.gov (United States)

2013-05-20

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State Data Capacity program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2013 and later years. We take this action to focus attention on an identified national need to provide technical assistance (TA) to States to improve their capacity to meet the data collection and reporting requirements of the Individuals with Disabilities Education Act (IDEA). We intend this priority to establish a TA center to improve State capacity to accurately collect and report IDEA data (Data Center).

Yucca Mountain Climate Technical Support Representative

International Nuclear Information System (INIS)

Sharpe, Saxon E

2007-01-01

The primary objective of Project Activity ORD-FY04-012, 'Yucca Mountain Climate Technical Support Representative', was to provide the Office of Civilian Radioactive Waste Management (OCRWM) with expertise on past, present, and future climate scenarios and to support the technical elements of the Yucca Mountain Project (YMP) climate program. The Climate Technical Support Representative was to explain, defend, and interpret the YMP climate program to the various audiences during Site Recommendation and License Application. This technical support representative was to support DOE management in the preparation and review of documents, and to participate in comment response for the Final Environmental Impact Statement, the Site Recommendation Hearings, the NRC Sufficiency Comments, and other forums as designated by DOE management. Because the activity was terminated 12 months early and experience a 27% reduction in budget, it was not possible to complete all components of the tasks as originally envisioned. Activities not completed include the qualification of climate datasets and the production of a qualified technical report. The following final report is an unqualified summary of the activities that were completed given the reduced time and funding

Systems study 'Alternative Entsorgung'. Final report. Technical annex 6

International Nuclear Information System (INIS)

1984-08-01

In the conditioning plant, fuel elements which have been stored for ten years are loaded into transport containers, unloaded, identified and welded into a dry storage box. The dry store barrel is introduced into a final storage container, which, after being closed, is packed in lost shielding. This so-called final storage barrel is finally placed in a transport container and leaves the conditioning plant in this form by rail for transport to the final storage mine. The fuel element method of treatment 'packing of three complete fuel elements' was used as the reference process. In addition, the method of treatment 'fuel elements dismantled into fuel rods' was also examined. The handling of fuel elements and secondary waste treatment in the reference process are described in detail. (orig./HP) [de

Multiparametric prostate MRI: technical conduct, standardized report and clinical use.

Science.gov (United States)

Manfredi, Matteo; Mele, Fabrizio; Garrou, Diletta; Walz, Jochen; Fütterer, Jurgen J; Russo, Filippo; Vassallo, Lorenzo; Villers, Arnauld; Emberton, Mark; Valerio, Massimo

2018-02-01

Multiparametric prostate MRI (mp-MRI) is an emerging imaging modality for diagnosis, characterization, staging, and treatment planning of prostate cancer (PCa). The technique, results reporting, and its role in clinical practice have been the subject of significant development over the last decade. Although mp-MRI is not yet routinely used in the diagnostic pathway, almost all urological guidelines have emphasized the potential role of mp-MRI in several aspects of PCa management. Moreover, new MRI sequences and scanning techniques are currently under evaluation to improve the diagnostic accuracy of mp-MRI. This review presents an overview of mp-MRI, summarizing the technical applications, the standardized reporting systems used, and their current roles in various stages of PCa management. Finally, this critical review also reports the main limitations and future perspectives of the technique.

IRIS Final Technical Progress Report

Energy Technology Data Exchange (ETDEWEB)

M. D. Carelli

2003-11-03

OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed

Strengthening the fission reactor nuclear science and engineering program at UCLA. Final technical report

International Nuclear Information System (INIS)

Okrent, D.

1997-01-01

This is the final report on DOE Award No. DE-FG03-92ER75838 A000, a three year matching grant program with Pacific Gas and Electric Company (PG and E) to support strengthening of the fission reactor nuclear science and engineering program at UCLA. The program began on September 30, 1992. The program has enabled UCLA to use its strong existing background to train students in technological problems which simultaneously are of interest to the industry and of specific interest to PG and E. The program included undergraduate scholarships, graduate traineeships and distinguished lecturers. Four topics were selected for research the first year, with the benefit of active collaboration with personnel from PG and E. These topics remained the same during the second year of this program. During the third year, two topics ended with the departure o the students involved (reflux cooling in a PWR during a shutdown and erosion/corrosion of carbon steel piping). Two new topics (long-term risk and fuel relocation within the reactor vessel) were added; hence, the topics during the third year award were the following: reflux condensation and the effect of non-condensable gases; erosion/corrosion of carbon steel piping; use of artificial intelligence in severe accident diagnosis for PWRs (diagnosis of plant status during a PWR station blackout scenario); the influence on risk of organization and management quality; considerations of long term risk from the disposal of hazardous wastes; and a probabilistic treatment of fuel motion and fuel relocation within the reactor vessel during a severe core damage accident

Preimplantation Genetic Diagnosis: Prenatal Testing for Embryos Finally Achieving Its Potential

Directory of Open Access Journals (Sweden)

Harvey J. Stern

2014-03-01

Full Text Available Preimplantation genetic diagnosis was developed nearly a quarter-century ago as an alternative form of prenatal diagnosis that is carried out on embryos. Initially offered for diagnosis in couples at-risk for single gene genetic disorders, such as cystic fibrosis, spinal muscular atrophy and Huntington disease, preimplantation genetic diagnosis (PGD has most frequently been employed in assisted reproduction for detection of chromosome aneuploidy from advancing maternal age or structural chromosome rearrangements. Major improvements have been seen in PGD analysis with movement away from older, less effective technologies, such as fluorescence in situ hybridization (FISH, to newer molecular tools, such as DNA microarrays and next generation sequencing. Improved results have also started to be seen with decreasing use of Day 3 blastomere biopsy in favor of polar body or Day 5 trophectoderm biopsy. Discussions regarding the scientific, ethical, legal and social issues surrounding the use of sequence data from embryo biopsy have begun and must continue to avoid concern regarding eugenic or inappropriate use of this technology.

Preimplantation Genetic Diagnosis: Prenatal Testing for Embryos Finally Achieving Its Potential

Science.gov (United States)

Stern, Harvey J.

2014-01-01

Preimplantation genetic diagnosis was developed nearly a quarter-century ago as an alternative form of prenatal diagnosis that is carried out on embryos. Initially offered for diagnosis in couples at-risk for single gene genetic disorders, such as cystic fibrosis, spinal muscular atrophy and Huntington disease, preimplantation genetic diagnosis (PGD) has most frequently been employed in assisted reproduction for detection of chromosome aneuploidy from advancing maternal age or structural chromosome rearrangements. Major improvements have been seen in PGD analysis with movement away from older, less effective technologies, such as fluorescence in situ hybridization (FISH), to newer molecular tools, such as DNA microarrays and next generation sequencing. Improved results have also started to be seen with decreasing use of Day 3 blastomere biopsy in favor of polar body or Day 5 trophectoderm biopsy. Discussions regarding the scientific, ethical, legal and social issues surrounding the use of sequence data from embryo biopsy have begun and must continue to avoid concern regarding eugenic or inappropriate use of this technology. PMID:26237262

Technical oversight for installation of TNX piezometers, Final Report

Energy Technology Data Exchange (ETDEWEB)

Pidcoe, W.W. Jr. [Westinghouse Savannah River Company, Aiken, SC (United States)

1997-06-05

Science Applications International Corporation was tasked under subcontract C002025P to provide technical oversight for the drilling of one pilot borehole, and the drilling and installation of five piezometers in the TNX Area Swamp. The work was performed in accordance with the Statement of Work in Task Order Proposal No. ER39-129 dated August 6, 1996. This report describes the activities associated with the performance of the task.

Technical recommendations for bilateral comparison in diagnosis radiology: part 3

International Nuclear Information System (INIS)

Peixoto, J.G.P.; Almeida, C.E.V. de

2015-01-01

Uncertainty and results homogeneity need to following the technical procedure to bilateral comparison, then we select the equipment used, reference conditions and the data file to be used for all participant laboratory. The partial results will be presentation at metrology and medical physics congress. (author)

[Anamnesis and clinical examination--also today still principles of sensible diagnosis?].

Science.gov (United States)

Seige, K

1985-11-15

The way to diagnosis goes over many parts, the end of which in each case means testing the obtained facts, critical overthinking and establishing the next steps up to the ascertainment of the real cause of the disease. At the beginning unchangedly stands the obtaining of the anamnesis of the patient and his disease by the physician himself who apart from the spoken word shall recognize, collect and classify plenty of observations at the patient with the help of as many senses as possible. This process is continued in the following physical examination of the patient with an immediate manual contact between the doctor's hand and the patient's skin. New findings are obtained, speculations will be approved or rejected. But finally in most cases the relationship between doctor and patient has become closer. A repeated critical consideration at the end of the physical examination with reasonable inclusion of the anamnestic data leads to the preliminary diagnosis. Only now the statements for further aimed diagnostic steps are done. Thus it is clearly to be stated that the fundaments of a reasonable diagnosis are the results of an integrated and critical synopsis of the objective and subjective findings at the patient by the doctor. History and physical examination are the unalterable condition before using technical possibilities.

Volatiles combustion in fluidized beds. Final technical report, 4 September 1992--4 June 1995

Energy Technology Data Exchange (ETDEWEB)

Pendergrass, R.A. II; Raffensperger, C.; Hesketh, R.P.

1996-02-29

The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization are being conducted to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. A review of the work conducted under this grant is presented in this Final Technical Report. Both experimental and theoretical work have been conducted to examine the inhibition of the combustion by the fluidized bed material, sand. It has been shown that particulate phase at incipient fluidization inhibits the combustion of propane by free radical destruction at the surface of sand particles within the particulate phase. The implications of these findings is that at bed temperatures lower than the critical temperatures, gas combustion can only occur in the bubble phase or at the top surface of a bubbling fluidized bed. In modeling fluidized bed combustion this inhibition by the particulate phase should be included.

Development of the biosphere code BIOMOD: final report

International Nuclear Information System (INIS)

Kane, P.

1983-05-01

Final report to DoE on the development of the biosphere code BIOMOD. The work carried out under the contract is itemised. Reference is made to the six documents issued along with the final report. These consist of two technical notes issued as interim consultative documents, a user's guide and a programmer's guide to BIOMOD, a database description, program test document and a technical note entitled ''BIOMOD - preliminary findings''. (author)

Intelligent systems in technical and medical diagnostics

CERN Document Server

Korbicz, Jozef

2013-01-01

For many years technical and medical diagnostics has been the area of intensive scientific research. It covers well-established topics as well as emerging developments in control engineering, artificial intelligence, applied mathematics, pattern recognition and statistics. At the same time, a growing number of applications of different fault diagnosis methods, especially in electrical, mechanical, chemical and medical engineering, is being observed. This monograph contains a collection of 44 carefully selected papers contributed by experts in technical and medical diagnostics, and constitutes

A Detector for Combined SPECT/CT. Final Technical Report

International Nuclear Information System (INIS)

Vivek Nagarkar

2006-01-01

The goal of the Phase I research was to demonstrate the feasibility of developing a high performance SPECT/CT detector module based on a combination of microcolumnar CsI(Tl) scintillator coupled to an EMCCD readout. We are very pleased to report that our Phase I research has demonstrated the technical feasibility of our approach with a very high degree of success. Specifically, we were able to implement a back-thinned EMCCD with a fiberoptic window which was successfully used to demonstrate the feasibility of near simultaneous radionuclide/CT using the proposed concept. Although significantly limited in imaging area (24 x 24 mm 2 ) and pixel resolution (512 x 512), this prototype has shown exceptional capabilities such as a single optical photon sensitivity, very low noise, an intrinsic resolution of 64 (micro)m for radionuclide imaging, and a resolution in excess of 10 lp/mm for x-ray imaging. Furthermore, the combination of newly developed, thick, microcolumnar CsI and an EMCCD has shown to be capable of operating in a photon counting mode, and that the position and energy information obtained from these data can be used to improve resolution in radionuclide imaging. Finally, the prototype system has successfully been employed for near simultaneous SPECT/CT imaging using both, 125 I and 99m Tc radioisotopes. The tomographic reconstruction data obtained using a mouse heart phantom and other phantoms clearly demonstrate the feasibility and efficacy of the detector in small animal research. The following were the objectives specified in the Phase I proposal: (1) In consultation with Professor Hasegawa, develop specifications for the Phase I/Phase II prototype detector; (2) Modify current vapor deposition protocols to fabricate ∼2 mm thick microcolumnar CsI(Tl) scintillators with excellent columnar structure, high light yield, and high spatial resolution; (3) Perform detailed characterization of the film morphology, light output, and spatial resolution, and use

Final Technical Report: "Representing Endogenous Technological Change in Climate Policy Models: General Equilibrium Approaches"

Energy Technology Data Exchange (ETDEWEB)

Ian Sue Wing

2006-04-18

The research supported by this award pursued three lines of inquiry: (1) The construction of dynamic general equilibrium models to simulate the accumulation and substitution of knowledge, which has resulted in the preparation and submission of several papers: (a) A submitted pedagogic paper which clarifies the structure and operation of computable general equilibrium (CGE) models (C.2), and a review article in press which develops a taxonomy for understanding the representation of technical change in economic and engineering models for climate policy analysis (B.3). (b) A paper which models knowledge directly as a homogeneous factor, and demonstrates that inter-sectoral reallocation of knowledge is the key margin of adjustment which enables induced technical change to lower the costs of climate policy (C.1). (c) An empirical paper which estimates the contribution of embodied knowledge to aggregate energy intensity in the U.S. (C.3), followed by a companion article which embeds these results within a CGE model to understand the degree to which autonomous energy efficiency improvement (AEEI) is attributable to technical change as opposed to sub-sectoral shifts in industrial composition (C.4) (d) Finally, ongoing theoretical work to characterize the precursors and implications of the response of innovation to emission limits (E.2). (2) Data development and simulation modeling to understand how the characteristics of discrete energy supply technologies determine their succession in response to emission limits when they are embedded within a general equilibrium framework. This work has produced two peer-reviewed articles which are currently in press (B.1 and B.2). (3) Empirical investigation of trade as an avenue for the transmission of technological change to developing countries, and its implications for leakage, which has resulted in an econometric study which is being revised for submission to a journal (E.1). As work commenced on this topic, the U.S. withdrawal

Virginia Solar Pathways Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bond, Katharine; Cosby, Sarah

2018-03-28

This Report provides a technical review of the final results of a funding award to Virginia Electric and Power Company (Dominion Energy Virginia (DEV) or the Company) for a project under the U.S. Department of Energy’s Solar Energy Technologies Office. The three-year project was formally known as the Virginia Solar Pathways Project (VSPP or the Project). The purpose of the VSPP was to develop a collaborative utility-administered solar strategy (Solar Strategy) for DEV’s service territory in the Commonwealth that could serve as a replicable model for other states with similar policy environments. The U.S. Department of Energy (DOE) funding award enabled DEV to take a focused approach to developing the Solar Strategy for its Virginia service territory. The structure and funding from the DOE award also facilitated valuable input from a formal stakeholder team convened to serve as advisors (Advisory Team) to the VSPP and contribute their perspectives and expertise to both the analysis and strategy development aspects of the Project. The development of the Solar Strategy involved three main goals: • Establish a policy and program framework that would integrate existing solar programs with new options appropriate for the Commonwealth’s policy environment and broader economic development objectives; • Promote wider deployment of solar within a low retail electric rate environment; and • Serve as a sustainable, utility-administered solar model that could be replicated in other states with similar policy environments, including, but not limited to, the entire Southeast region. In support of the VSPP goals, the Project Team commissioned four studies to support the Solar Strategy development. Two studies, completed by Navigant Consulting, focused on the integration of solar into the electric grid. The first solar integration study focused on integration of solar into the distribution grid where the utility system directly connects to and serves end-use customers

FOREX trading strategy formation using technical analysis

OpenAIRE

Klimavičius, Domas

2010-01-01

FOREX technical analysis indicators, their characteristics and capabilities are researched in this final master thesis. The main goal of this thesis is to determine if technical analysis indicators can recognise patterns in price movements and if they can predict future price movement. The first part of the thesis presents with FOREX theoretical aspects, its characteristics and participants. In the second part of the thesis FOREX analysis tools are overviewed, focusing on technical analysis. ...

Final Technical Report for Year 5 Early Career Research Project "Viscosity and equation of state of hot and dense QCD matter"

Energy Technology Data Exchange (ETDEWEB)

Molnar, Denes [Purdue Univ., West Lafayette, IN (United States)

2016-05-25

The Section below summarizes research activities and achievements during the fifth (last) year of the PI’s Early Career Research Project (ECRP). Unlike the first four years of the project, the last year was not funded under the American Recovery and Reinvestment Act (ARRA). The ECRP advanced two main areas: i) radiative 3 ↔ 2 radiative transport, via development of a new computer code MPC/Grid that solves the Boltzmann transport equation in full 6+1D (3X+3V+time); and ii) application of relativistic hydrodynamics, via development of a self-consistent framework to convert viscous fluids to particles. In Year 5 we finalized thermalization studies with radiative gg ↔ ggg transport (Sec. 1.1.1) and used nonlinear covariant transport to assess the accuracy of fluid-to-particle conversion models (Sec. 1.1.2), calculated observables with self-consistent fluid-to-particle conversion from realistic viscous hydrodynamic evolution (Secs. 1.2.1 and 1.2.2), extended the covariant energy loss formulation to heavy quarks (Sec. 1.4.1) and studied energy loss in small systems (Sec. 1.4.2), and also investigated how much of the elliptic flow could have non-hydrodynamic origin (Sec 1.3). Years 1-4 of the ECRP were ARRA-funded and, therefore, they have their own report document ’Final Technical Report for Years 1-4 of the Early Career Research Project “Viscosity and equation of state of hot and dense QCD matter”’ (same award number DE-SC0004035). The PI’s group was also part of the DOE JET Topical Collaboration, a multi-institution project that overlapped in time significantly with the ECRP. Purdue achievements as part of the JET Top- ical Collaboration are in a separate report “Final Technical Report summarizing Purdue research activities as part of the DOE JET Topical Collaboration” (award DE-SC0004077).

75 FR 33682 - Export Administration Regulations; Technical Amendments

Science.gov (United States)

2010-06-15

...-01] RIN 0694-AE93 Export Administration Regulations; Technical Amendments AGENCY: Bureau of Industry... Bureau of Industry and Security (BIS) makes a technical amendment to the Export Administration... review of final decisions and orders issued in BIS export control administrative enforcement proceedings...

Health care fraud and abuse data collection program: technical revisions to Healthcare Integrity and Protection Data Bank data collection activities. Final rule.

Science.gov (United States)

2004-09-21

The rule finalizes technical changes to the Healthcare Integrity and Protection Data Bank (HIPDB) data collection reporting requirements by clarifying the types of personal numeric identifiers that may be reported to the data bank in connection with adverse actions. The rule clarifies that in lieu of a Social Security Number (SSN), an individual taxpayer identification number (ITIN) may be reported to the data bank when, in those limited situations, an individual does not have an SSN.

The evaluation of a framework for measuring the non-technical ward round skills of final year nursing students: An observational study.

Science.gov (United States)

Murray, Kara; McKenzie, Karen; Kelleher, Michael

2016-10-01

The importance of non-technical skills (NTS) to patient outcomes is increasingly being recognised, however, there is limited research into how such skills can be taught and evaluated in student nurses in relation toward rounds. This pilot study describes an evaluation of a NTS framework that could potentially be used to measure ward round skills of student nurses. The study used an observational design. Potential key NTS were identified from existing literature and NTS taxonomies. The proposed framework was then used to evaluate whether the identified NTS were evident in a series of ward round simulations that final year general nursing students undertook as part of their training. Finally, the views of a small group of qualified nurse educators, qualified nurses and general nursing students were sought about whether the identified NTS were important and relevant to practice. The proposed NTS framework included seven categories: Communication, Decision Making, Situational Awareness, Teamwork and Task Management, Student Initiative and Responsiveness to Patient. All were rated as important and relevant to practice. The pilot study suggests that the proposed NTS framework could be used as a means of evaluating student nurse competencies in respect of many non-technical skills required for a successful ward round. Further work is required to establish the validity of the framework in educational settings and to determine the extent to which it is of use in a non-simulated ward round setting. Copyright © 2016 Elsevier Ltd. All rights reserved.

Technical progress in nuclear medical heart diagnosis

International Nuclear Information System (INIS)

Standke, R.; Hoer, G.

1989-01-01

The rapid development in nuclear cardiology worldwide can hardly be surveyed from the point of view of one center. In connection with the general nuclear cardiologic development this study describes a multiparameter analysis of regional left ventricular function during exercise, and the method of sectoranalysis for quantification of myocardial SPECT. Finally a one-step procedure to quantify left ventricular function and myocardial perfusion is presented. (orig.) [de

Using communication norms in socio-technical systems

NARCIS (Netherlands)

Weigand, H.; Whitworth, B.; de Moor, A.

2009-01-01

Often socio-technical systems are designed simply on the basis of what the user asks, and without considering explicitly whether the required process structure is right and wrong. However, poor communication may cause many problems. Therefore, a design cycle should always include diagnosis, and in

High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

International Nuclear Information System (INIS)

Paul T. Fini; Shuji Nakamura

2005-01-01

In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

Polar source analysis : technical memorandum

Science.gov (United States)

2017-09-29

The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

Science.gov (United States)

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

Final Scientific and Technical Report State and Regional Biomass Partnerships

Energy Technology Data Exchange (ETDEWEB)

Handley, Rick; Stubbs, Anne D.

2008-12-29

The Northeast Regional Biomass Program successfully employed a three pronged approach to build the regional capacity, networks, and reliable information needed to advance biomass and bioenergy technologies and markets. The approach included support for state-based, multi-agency biomass working groups; direct technical assistance to states and private developers; and extensive networking and partnership-building activities to share objective information and best practices.

NUSC Technical Publications Guide.

Science.gov (United States)

1985-05-01

Facility personnel especially that of A. Castelluzzo, E. Deland, J. Gesel , and E. Szlosek (all of Code 4343). Reviewed and Approved: 14 July 1980 D...their technical content and format. Review and approve the manual outline, the review manuscript, and the final camera - reproducible copy. Conduct in

Medium energy measurements of N-N parameters. Final technical report, April 1, 1994--September 30, 1996

International Nuclear Information System (INIS)

Ambrose, D.; Betts, W.; Coffey, P.; Glass, G.; McDonough, J.; Riley, P.; Tang, J.L.

1998-08-01

This document is a final technical report describing the accomplishments of the medium/high energy nuclear physics research program at the University of Texas at Austin. The research program had four main thrusts, only one of which can be considered as measurements of N-N parameters: (1) finishing the data analyses associated with recent LAMPF and TRIUMPF N-N experiments, whose overall purpose has been the determination of the nucleon-nucleon amplitudes, both for isospin 0 and 1 at medium energies; (2) continuing work on BNL E871, a search for rare decay modes of the K L ; (3) work on the RHIC-STAR project, an experiment to create and study a quark gluon plasma and nuclear matter at high energy density; (4) beginning a new AGS experiment (E896) which will search for the lowest mass state of the predicted strange di-baryons, the Ho, and other exotic states of nuclear matter through nucleus-nucleus collisions

NTRCI Legacy Engine Research and Development Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

2011-12-31

The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Brown, R. C.; McCarley, T. M.

2006-05-04

. Platform teams organize faculty and students for cross-disciplinary, systems-oriented research and collaborative learning. To date, nine platforms have been developed, although these will most likely be reorganized into a smaller number of broader topics. In the spring of 2004, BRT faculty initiated a regional partnership and collaborative learning program with colleagues at the University of Minnesota, Kansas State University, and South Dakota State University to develop distance education courses in biorenewable resources and technology. As a fledgling graduate program, the BRT graduate program didn’t have the breadth of resources to offer a large number of courses in biorenewables. Other schools faced a similar problem. The academic consortium as first conceived would allow students from the member schools to enroll in biorenewables courses from any of the participating schools, which would assure the necessary enrollment numbers to offer specialized course work. Since its inception, the collaborative curriculum partnership has expanded to include Louisiana State University and the University of Wisconsin. A second international curriculum development campaign was also initiated in the spring of 2004. In particular, several BRT faculty teamed with colleagues at the University of Arkansas, University of Washington, University of Gent (Belgium), National Polytechnic Institute of Toulouse (France), and Technical University of Graz (Austria) to develop an EU-US exchange program in higher education and vocational education/training (entitled “Renewable Resources and Clean Technology”).

Ageing management technical information investigations

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

In February 2013, there are 50 units of commercial nuclear power plants (NPPs) in Japan. We enter into a period that 20 units of them are operating for more than 30 years. Currently, regulation imposes utilities to conduct ageing technical evaluations of each unit before operation of 30 years from the commissioning, to develop the long term maintenance management policy for next 10 years and to submit to the regulatory authority the policy with the report on ageing management technical evaluation (AMTE) for each NPP. It is necessary for regulatory side to develop technical information bases incorporating latest technical knowledge as operating experiences in domestic and abroad on ageing of the plants necessary to conduct reviews of AMTE for each unit. Based on these standpoints, technical information bases investigations have been conducted from the viewpoints of material degradation of ageing NPPs. In order to develop scientific regulator judgment bases related to ageing management (AM) and long-term operation (LTO), investigations on latest information on ageing management in domestic and abroad are conducted and a set of documents including technical evaluation review manuals necessary to conduct AMTE are prepared. To utilize the results of the investigations for ageing technical evaluation, database including latest information related to AM and LTO are developed, ran and operated. In addition, investigations related to Fugen nuclear plant, under decommissioning plants, investigations on mechanism of stress corrosion cracking (SCC), thermal ageing and preventive technologies for SCC, detection and diagnosis technology for ageing degradation and condition monitoring technology are performed to validate and confirm effectiveness of the technologies. (author)

Technical assistance for Meharry Medical College Energy Efficiency Project. Final project status and technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-08

This report presents the results of a program to provide technical assistance to Meharry Medical College. The purpose of the program is to facilitate Meharry`s effort to finance a campus-wide facility retrofit. The US Department of Energy (USDOE) funded the program through a grant to the Tennessee Department of Economic and Community Development (TECD). The University of Memphis-Technology and Energy Services (UM-TES), under contract to TECD, performed program services. The report has three sections: (1) introduction; (2) project definition, financing, and participants; and (3) opportunities for federal participation.

Fundamental studies of the chemical vapor deposition of diamond. Final technical report, April 1, 1988--December 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Nix, W.D.

1995-05-01

We submit here a final technical report for the research program entitled: Fundamental Studies of the Chemical Vapor Deposition of Diamond, DOE Grant No. DE-FG05-88ER45345-M006. This research program was initiated in 1988 under the direction of the late Professor David A. Stevenson and was renewed in 1992. Unfortunately, at the end of 1992, just as the last phase of this work was getting underway, Professor Stevenson learned that he had developed mesothelioma, a form of cancer based on asbestos. Professor Stevenson died from that disease in February of 1994. Professor William D. Nix, the Chairman of the Materials Science department at Stanford was named the Principal Investigator. Professor Nix has assembled this final technical report. Much of the work of this grant was conducted by Mr. Paul Dennig, a graduate student who will receive his Ph.D. degree from Stanford in a few months. His research findings are described in the chapters of this report and in the papers published over the past few years. The main discovery of this work was that surface topology plays a crucial role in the nucleation of diamond on silicon. Dennig and his collaborators demonstrated this by showing that diamond nucleates preferentially at the tips of asperities on a silicon surface rather than in the re-entrant comers at the base of such asperities. Some of the possible reasons for this effect are described in this report. The published papers listed on the next page of this report also describe this research. Interested persons can obtain copies of these papers from Professor Nix at Stanford. A full account of all of the research results obtained in this work is given in the regular chapters that follow this brief introduction. In addition, interested readers will want to consult Mr. Dennig`s Ph.D. dissertation when it is made available later this year.

Motion Capture Technique Applied Research in Sports Technique Diagnosis

Directory of Open Access Journals (Sweden)

Zhiwu LIU

2014-09-01

Full Text Available The motion capture technology system definition is described in the paper, and its components are researched, the key parameters are obtained from motion technique, the quantitative analysis are made on technical movements, the method of motion capture technology is proposed in sport technical diagnosis. That motion capture step includes calibration system, to attached landmarks to the tester; to capture trajectory, and to analyze the collected data.

The technical-tactical preparation of the boxers from Sancti Spíritus

Directory of Open Access Journals (Sweden)

Juan Manuel García Hernández

2018-05-01

Full Text Available The investigative work presented is part of the daily work of the group of trainers that works in the Provincial Boxing Academy in the province of Sancti Spíritus. The problem investigated responds to the technological demands that exist at the provincial level, with the objective of applying a set of technical-tactical actions to raise the level of preparation of the boxers of Sancti Spiritus that allows to obtain satisfactory results in the competitive order. The diagnosis was developed based on the results of the technical tests of the participation of the boxers from Sancti Spiritus in the Playa Girón National Championships in the 2013-2016 cycle. The final results are compared with those issued by the specialists of the National Technical Commission in the present Playa Girón National Championship held in December 2017, in the Sala Yara of the Province of Sancti Spíritus. The population that used for this investigation is made up of 20 elite category boxers from the province of Sancti Spíritus. The achievements correspond to the work done collectively and individually from the shortcomings and potentials presented by the investigated boxers from Sancti Spiritus. Therefore, it was possible to demonstrate that taking into account the behavior of the main dimensions and indicators of the technical tests, good competitive results can be obtained and that it facilitated the differentiated work with each boxer taking into account the scientific and technical advances at our disposal. In order to comply with this research, theoretical, empirical and mathematical methods were used; among them we can mention: Historical-logical, synthesis analysis, inductive deductive, observation, interview, pre-experiment and descriptive statistics.

Minutes of the IFMIF technical meeting

International Nuclear Information System (INIS)

Nakamura, H.; Takeda, M.; Ida, M.; Maebara, S.; Yutani, T.; Sugimoto, M.

2004-03-01

The IFMIF Technical Meeting was held on December 4-5, 2003 at Shiran-kaikan, Kyoto University. The main objectives are 1) to finalize the Comprehensive Design Report (CDR), 2) to discuss IFMIF cost and organization, 3) to review technical status of major systems, transition phase activities and EVEDA plan. This report presents a brief summary of the results of the meeting. Agenda, participants list and presentation materials are attached as Appendix. (author)

Establishment of the International Power Institute. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Julius E. Coles

2000-08-04

The International Power Institute, in collaboration with American industries, seeks to address technical, political, economic and cultural issues of developing countries in the interest of facilitating profitable transactions in power related infrastructure projects. IPI works with universities, governments and commercial organizations to render project-specific recommendations for private-sector investment considerations. IPI also established the following goals: Facilitate electric power infrastructure transactions between developing countries and the US power industry; Collaborate with developing countries to identify development strategies to achieve energy stability; and Encourage market driven solutions and work collaboratively with other international trade energy, technology and banking organizations.

High tracking resolution detectors. Final Technical Report

International Nuclear Information System (INIS)

Vasile, Stefan; Li, Zheng

2010-01-01

High-resolution tracking detectors based on Active Pixel Sensor (APS) have been valuable tools in Nuclear Physics and High-Energy Physics research, and have contributed to major discoveries. Their integration time, radiation length and readout rate is a limiting factor for the planed luminosity upgrades in nuclear and high-energy physics collider-based experiments. The goal of this program was to demonstrate and develop high-gain, high-resolution tracking detector arrays with faster readout, and shorter radiation length than APS arrays. These arrays may operate as direct charged particle detectors or as readouts of high resolution scintillating fiber arrays. During this program, we developed in CMOS large, high-resolution pixel sensor arrays with integrated readout, and reset at pixel level. Their intrinsic gain, high immunity to surface and moisture damage, will allow operating these detectors with minimal packaging/passivation requirements and will result in radiation length superior to APS. In Phase I, we designed and fabricated arrays with calorimetric output capable of sub-pixel resolution and sub-microsecond readout rate. The technical effort was dedicated to detector and readout structure development, performance verification, as well as to radiation damage and damage annealing.

Diverticular Disease and Colorectal Cancer: Incidental Diagnosis or Real Association? Final Answer.

Science.gov (United States)

Regula, Jaroslaw

2016-10-01

Associations between diverticular disease of the colon and the colorectal cancer has been studied for >60 years. Observational, cross-sectional, and case-control studies as well as large population-based studies gave conflicting results and association was not fully proven. Obtaining the proof was difficult because both diseases share similar clinical characteristics, both increase with age, and both involve similar dietary factors. Long-term observations are difficult as diagnostic methods changed over time from barium enema 50 to 60 years ago, through endoscopy, up to CT and MR in recent years. Cancer or adenomas may be missed within diverticular segment; diverticula may be underreported in patients with colon cancer diagnosis. Most recent 2 large cohort studies have solved the dilemma. These studies have clearly shown that diverticular disease does not increase the risk of colon cancer after the first year of diagnosis. Within the first year of diagnosis the association is strong, most probably due to difficulties with differential diagnosis and misclassifications and shared symptoms. Findings of these studies have led to the conclusion that colon cancer has to be excluded using modern techniques after the first episode of suspected diverticulitis.

Expectation and task for constructing the volume reduction system of removed soils. In search of the technical integrity from the intermediate storage to final disposal

International Nuclear Information System (INIS)

Mori, Hisaki

2016-01-01

The intermediate storage volume of the removed soils and incineration ash in Fukushima is supposed about 22 million cubic meters. Within 30 years after starting the intermediate storage, the final disposal outside Fukushima prefecture to these removed soils and incineration ash is determined by the law. Because these removed soils are the very-very low radio activity, the volume reduction method is most effective to reduce the burden of the final disposal. As the volume reduction technology is the stage of research and development, the possibility of the introduction of the volume reduction technology that has the consistency of the final disposal technology is evaluated from the point of view of cost. Since this business is accompanied by economic and technical risk to implement private companies, this project is considered appropriate to be implemented as a national project. (author)

Technical and clinical performance of a new assay to detect squamous cell carcinoma antigen levels for the differential diagnosis of cervical, lung, and head and neck cancer.

Science.gov (United States)

Holdenrieder, Stefan; Molina, Rafael; Qiu, Ling; Zhi, Xiuyi; Rutz, Sandra; Engel, Christine; Kasper-Sauer, Pia; Dayyani, Farshid; Korse, Catharina M

2018-04-01

In squamous cell carcinoma, squamous cell carcinoma antigen levels are often elevated. This multi-center study evaluated the technical performance of a new Elecsys ® squamous cell carcinoma assay, which measures serum squamous cell carcinoma antigen 1 and 2 levels in an equimolar manner, and investigated the potential of squamous cell carcinoma antigen for differential diagnosis of cervical, lung, and head and neck squamous cell carcinoma.Assay precision and method comparison experiments were performed across three European sites. Reference ranges for reportedly healthy individuals were determined using samples from banked European and Chinese populations. Differential diagnosis experiments determined whether cervical, lung, or head and neck cancer could be differentiated from apparently healthy, benign, or other malignant cohorts using squamous cell carcinoma antigen levels alone. Squamous cell carcinoma antigen cut-off levels were calculated based on squamous cell carcinoma antigen levels at 95% specificity. Repeatability coefficients of variation across nine analyte concentrations were ≤5.3%, and intermediate precision coefficients of variation were ≤10.3%. Method comparisons showed good correlations with Architect and Kryptor systems (slopes of 1.1 and 1.5, respectively). Reference ranges for 95th percentiles for apparently healthy individuals were 2.3 ng/mL (95% confidence interval: 1.9-3.8; European cohort, n = 153) and 2.7 ng/mL (95% confidence interval: 2.2-3.3; Chinese cohort, n = 146). Strongest differential diagnosis results were observed for cervical squamous cell carcinoma: receiver operating characteristic analysis showed that squamous cell carcinoma antigen levels (2.9 ng/mL cut-off) differentiate cervical squamous cell carcinoma (n = 127) from apparently healthy females (n = 286; area under the curve: 86.2%; 95% confidence interval: 81.8-90.6; sensitivity: 61.4%; specificity: 95.6%), benign diseases (n = 187; area

Scalable data management, analysis and visualization (SDAV) Institute. Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Geveci, Berk [Kitware, Inc., Clifton Park, NY (United States)

2017-03-28

The purpose of the SDAV institute is to provide tools and expertise in scientific data management, analysis, and visualization to DOE’s application scientists. Our goal is to actively work with application teams to assist them in achieving breakthrough science, and to provide technical solutions in the data management, analysis, and visualization regimes that are broadly used by the computational science community. Over the last 5 years members of our institute worked directly with application scientists and DOE leadership-class facilities to assist them by applying the best tools and technologies at our disposal. We also enhanced our tools based on input from scientists on their needs. Many of the applications we have been working with are based on connections with scientists established in previous years. However, we contacted additional scientists though our outreach activities, as well as engaging application teams running on leading DOE computing systems. Our approach is to employ an evolutionary development and deployment process: first considering the application of existing tools, followed by the customization necessary for each particular application, and then the deployment in real frameworks and infrastructures. The institute is organized into three areas, each with area leaders, who keep track of progress, engagement of application scientists, and results. The areas are: (1) Data Management, (2) Data Analysis, and (3) Visualization. Kitware has been involved in the Visualization area. This report covers Kitware’s contributions over the last 5 years (February 2012 – February 2017). For details on the work performed by the SDAV institute as a whole, please see the SDAV final report.

Medicare and Medicaid programs; salary equivalency guidelines for physical therapy, respiratory therapy, speech language pathology, and occupational therapy services; revised effective date and technical correction--HCFA. Final rule; delay of effective date and correction.

Science.gov (United States)

1998-03-31

This document delays the effective date of the final rule on salary equivalency guidelines, published in the Federal Register (63 FR 5106) on January 30, 1998, from April 1, 1998 to April 10, 1998. In addition, we are making a technical correction in the preamble to the January 30, 1998 final rule.

The UP3-UP2 800 reprocessing plants control systems. Use of tools for the diagnosis, the track of control softwares and the management of technical data

International Nuclear Information System (INIS)

Chabert, J.; Michon, J.C.

1995-01-01

After a rapid presentation of control systems architectures of the La Hague COGEMA reprocessing plants, details are given about the tools used to master the control and instrumentation softwares and technical data. The paper focusses more particularly on the CML (Software Maintenance Center) tool which manages the software versions installed on the driving system, on the SYDDEX tool devoted to the management of the control and instrumentation associated data and documents, and on the SAD tool used for diagnosis assistance. (J.S.). 5 figs

Summary of the ITER final design report. July 2001

International Nuclear Information System (INIS)

2001-01-01

This document is a summary of the ITER final design report foreseen during the current, Engineering Design Activities (EDA), phase of the ITER project. The report presents the results of collaborative design and supporting technical work undertaken by the ITER Joint Central team (JCT) and the Home Teams (HT) of the parties to the agreement on co-operation in the Engineering Design Activities for ITER (the ITER EDA Agreement). This report marks the achievement of the full technical scope of activities indicated in the ITER EDA Agreement, with a final design which meets the programmatic objective defined in the Agreement and satisfies detailed scientific, technical and costing objectives set by ITER Council in 1998

New usable technical specifications

International Nuclear Information System (INIS)

Webster, S.A.; Tomasi, L.T.; Bernier, R.A.

1989-01-01

After 2 yr of preparation, 1988 finally saw the nuclear industry writing operator-oriented technical specifications. This effort is a continuation of previous efforts to develop improved and usable standard technical specifications (STSs), and is being conducted by the four nuclear steam supply system vendor owners' groups under the auspices of the Nuclear Management Resources Council. Each participant is currently preparing a set of improved STSs based on a writer's guide that was developed through a combined industry effort. In May of 1987, a Human Factors Improvements to Technical Specifications (HFITS) task group was formed to prepare a writer's guide for improved, industrywide STSs. This task group was composed of two representatives from each owners' group, one with a human factors background and one with some operations background. Two documents were prepared in 6 months, a human factors report laying the groundwork for the considerations to go into technical specifications and a writer's guide for their preparation. This paper reports on the application of this writer's guide to the writing of improved STS

TADS Final Evaluation Report, 1980-81. Appendix S.

Science.gov (United States)

Suarez, Tanya M.; And Others

The document contains the final report of the Technical Assistance Development System (TADS), a program which provided technical assistance (TA) services to 53 Handicapped Children's Early Education Program (HCEEP) demonstration projects and 13 State Implementation Grants (SIGs). The evaluation report is divided into five sections. Section 1…

Final report. Geothermal Energy Program: Information dissemination, public outreach, and technical analysis activities. April 1, 1999 to December 31, 2001. USDOE Grant No. DE-FG01-99-EE35098

Energy Technology Data Exchange (ETDEWEB)

Lund, John W.

2002-03-22

This is the final report of the accomplishments of the geothermal energy program: information dissemination, public outreach, and technical analysis activities by the project team consisting of the Geo-Heat Center, Geothermal Resources Council, Geothermal Education Office, Geothermal Energy Association, and the Washington State University Energy Program.

Fifth technical meeting on quality

International Nuclear Information System (INIS)

Girard, A.

1998-01-01

This article reports on the 5th Technical Meeting on Quality which was held in San Diego on 20-22 October 1997 and which was attended by representatives of the Home and Joint Central Team and of manufacturers currently involved in the Large R and D projects. The meeting made progress towards the finalization of the ITER Quality Manual document for inclusion in the Final Design Report and the definition of the quality necessary for ITER procurement and construction

Forecasting Resource as a Method of Increasing the Security of Technical Devices

Science.gov (United States)

Cherepanov, Anatoly P.; Lyapustin, Pavel K.

2017-10-01

The article shows a method of increasing the safe operation of technical devices at various stages of the life cycle according to the proposed classification parameters of the resource by applying the model of resource prediction. The model takes into account the presence of defects, the rate of corrosion and corrosion resistance of the material, the volume of technical diagnosis, the degree of risk in case of failure or damage of technical devices. The article shows the application of the model resource of the technical device from the manufacture to the end of its service life.

Functional criteria for emergency response facilities. Technical report (final)

International Nuclear Information System (INIS)

1981-02-01

This report describes the facilities and systems to be used by nuclear power plant licensees to improve responses to emergency situations. The facilities include the Technical Support Center (TSC), Onsite Operational Support Center (OSC), and Nearsite Emergency Operations Facility (EOF), as well as a brief discussion of the emergency response function of the control room. The data systems described are the Safety Parameter Display System (SPDS) and Nuclear Data Link (NDL). Together, these facilities and systems make up the total Emergency Response Facilities (ERFs). Licensees should follow the guidance provided both in this report and in NUREG-0654 (FEMA-REP-1), Revision 1, for design and implementation of the ERFs

[Arthrography of the temporomandibular joint. Indications, technic and interpretation].

Science.gov (United States)

Jend, H H; Triebel, H J; Jend-Rossmann, I

1986-09-01

Articular dysfunction of the TMJ with anterior displacement of the disc ("internal derangement") is an entity which has been separated from other types of the "myofascial pain syndromes" and which can be treated conservatively or by surgery. Arthrography of the TMJ has contributed greatly to an understanding of normal and abnormal function and, in many cases, it can provide a diagnosis. On the basis of our experience with 80 investigations we discuss technical problems and the clinical indications. The indications for arthrography are in the pre-operative diagnosis, when clinical findings are uncertain, in order to demonstrate perforation, in order to confirm a suspected diagnosis and to assist in prosthetic treatment.

Final Technical Report for Award DESC0011912, "Trimodal Tapping Mode Atomic Force Microscopy: Simultaneous 4D Mapping of Conservative and Dissipative Probe-Sample Interactions of Energy-Relevant Materials”

Energy Technology Data Exchange (ETDEWEB)

Solares, Santiago D. [George Washington Univ., Washington, DC (United States)

2017-09-22

The final project report covering the period 7/1/14-6/30/17 provides an overview of the technical accomplishments in the areas of (i) fundamental viscoelasticity, (ii) multifrequency atomic force microscopy, and (iii) characterization of energy-relevant materials with atomic force microscopy. A list of publications supported by the project is also provided.

The role of non-technical skills in surgery.

Science.gov (United States)

Agha, Riaz A; Fowler, Alexander J; Sevdalis, Nick

2015-12-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care.

The role of non-technical skills in surgery

Science.gov (United States)

Agha, Riaz A.; Fowler, Alexander J.; Sevdalis, Nick

2015-01-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care. PMID:26904193

Final Technical Report - SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodynamics

International Nuclear Information System (INIS)

Schnack, Dalton D.

2012-01-01

Final technical report for research performed by Dr. Thomas G. Jenkins in collaboration with Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodyanics, DE-FC02-06ER54899, for the period of 8/15/06 - 8/14/11. This report centers on the Slow MHD physics campaign work performed by Dr. Jenkins while at UW-Madison and then at Tech-X Corporation. To make progress on the problem of RF induced currents affect magnetic island evolution in toroidal plasmas, a set of research approaches are outlined. Three approaches can be addressed in parallel. These are: (1) Analytically prescribed additional term in Ohm's law to model the effect of localized ECCD current drive; (2) Introduce an additional evolution equation for the Ohm's law source term. Establish a RF source 'box' where information from the RF code couples to the fluid evolution; and (3) Carry out a more rigorous analytic calculation treating the additional RF terms in a closure problem. These approaches rely on the necessity of reinvigorating the computation modeling efforts of resistive and neoclassical tearing modes with present day versions of the numerical tools. For the RF community, the relevant action item is - RF ray tracing codes need to be modified so that general three-dimensional spatial information can be obtained. Further, interface efforts between the two codes require work as well as an assessment as to the numerical stability properties of the procedures to be used.

Prenatal Diagnosis of Osteogenesis Imperfecta

Directory of Open Access Journals (Sweden)

Özgür Özyüncü

2010-04-01

Full Text Available Skeletal dysplasias are a group of diseases with a wide spectrum related to bone and cartilage. Some forms are lethal whereas some forms have milder clinical progression. Prenatal diagnosis of skeletal dysplasias may be possible especially when there is an index case in the family. Ultrasonography plays the central role in prenatal diagnosis and most common sonographic features are angulation of long bones, bending of femur or bowing signin the long bones. We present a case whose follow up for fetal short extremities ended with termination of pregnancy. The differential diagnosis is hard and depend especially on the fetal x-ray. Final diagnosis was lethal type osteogenesis imperfecta.

AIPM Final Report

Energy Technology Data Exchange (ETDEWEB)

John Mookken

2006-06-30

The final AIPM project report consists of six sections. Each section includes information on the original AIPM project and extension work on the high temperature design. The first section (1) provides an overview of the program and highlights the significant targets to meet at the end of the program. The next section (2) summarizes the significant technical accomplishments by the SEMIKRON AIPM team during the course of the project. Greater technical details are provided in a collection of all the quarterly reports which can be found in the appendix. Section three (3) presents some the more significant technical data collected from technology demonstrators. Section four (4) analyzes the manufacturing cost or economic aspects of producing 100,000 units/yr. Section five (5) describes the commercialization efforts of the AIPM technology into the automotive market. The last section (6) recommends follow on work that will build on the efforts and achievements of the AIPM program.

ITER technical advisory committee meeting

International Nuclear Information System (INIS)

Fujiwara, M.

2001-01-01

The 17th Meeting of the ITER Technical Advisory Committee (TAC-17) was held on February 19-22, the ITER Garching Work Site in Germany. The objective of the meeting was to review the Draft Final Design Report of ITER-FEAT and assess the ability of the self-consistent overall design both to satisfy the technical objectives previously defined and to meet the cost limitations. TAC-17 was also organized to confirm that the design and critical elements, with emphasis on the key recommendations made at previous TAC meetings, are such as to extend the confidence in starting ITER construction. It was also intended to provide the ITER Council, scheduled to meet on 27 and 28 February in Toronto, with a technical assessment and key recommendations of the above mentioned report

Technical specification improvements to containment heat removal and emergency core cooling systems: Final report

International Nuclear Information System (INIS)

Sullivan, W.P.; Ha, C.; Pentzien, D.C.; Visweswaran, S.

1988-07-01

This report presents the results of an analysis for technical specification improvements to the emergency core cooling systems (ECCS) and containment heat removal systems (EPRI Research Project 2142-3). The objective of this project is to further develop a reliability- and risk-based methodology to provide improvements by considering groups of surveillance test intervals and allowed out-of-service times jointly. This was done for the technical specifications for the ECCS, containment heat removal equipment, and supporting systems of a boiling water reactor plant. The project (1) developed a methodology for optimizing groups of surveillance test intervals and allowed out-of-service times jointly, (2) applied the methodology in a case study of a specific operating plant, Hatch-2, and (3) evaluated benefits of the application. The results of the case study demonstrate that beneficial technical specification improvements can be realized with application of the methodology. By tightening a small group of sensitive surveillance test intervals (STIs) and allowed out-of-service times (AOTs), a larger group of less sensitive STIs and AOTs can be extended resulting in an overall plant operating cost improvement without reducing the plant safety. The reliability- and risk-based methodology and results from this project can be effectively applied for technical specification improvements at other operating plants

ITER EDA technical activities

International Nuclear Information System (INIS)

Aymar, R.

1998-01-01

Six years of technical work under the ITER EDA Agreement have resulted in a design which constitutes a complete description of the ITER device and of its auxiliary systems and facilities. The ITER Council commented that the Final Design Report provides the first comprehensive design of a fusion reactor based on well established physics and technology

DOE Utility Matching Program Final Technical Report

International Nuclear Information System (INIS)

Haghighat, Alireza

2002-01-01

This is the Final report for the DOE Match Grant (DE-FG02-99NE38163) awarded to the Nuclear and Radiological Engineering (NRE) Department, University of Florida, for the period of September 1999 to January 2002. This grant has been instrumental for maintaining high-quality graduate and undergraduate education at the NRE department. The grant has been used for supporting student entry and retention and for upgrading nuclear educational facilities, nuclear instrumentation, computer facilities, and computer codes to better enable the incorporation of experimental experiences and computer simulations related to advanced light water fission reactor engineering and other advanced reactor concepts into the nuclear engineering course curricula

Vadose zone microbial community structure and activity in metal/radionuclide contaminated sediments. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Balkwill, David L.

2002-08-17

This final technical report describes the research carried out during the final two months of the no-cost extension ending 11/14/01. The primary goals of the project were (1) to determine the potential for transformation of Cr(VI) (oxidized, mobile) to Cr(III) (reduced, immobile) under unsaturated conditions as a function of different levels and combinations of (a) chromium, (b) nitrate (co-disposed with Cr), and (c) molasses (inexpensive bioremediation substrate), and (2) to determine population structure and activity in experimental treatments by characterization of the microbial community by signature biomarker analysis and by RT-PCR and terminal restriction fragment length polymorphism (T-RFLP) and 16S ribosomal RNA genes. It was determined early in the one-year no-cost extension period that the T-RFLP approach was problematic in regard to providing information on the identities of microorganisms in the samples examined. As a result, it could not provide the detailed information on microbial community structure that was needed to assess the effects of treatments with chromium, nitrate, and/or molasses. Therefore, we decided to obtain the desired information by amplifying (using TR-PCR, with the same primers used for T-RFLP) and cloning 16S rRNA gene sequences from the same RNA extracts that were used for T-RFLP analysis. We also decided to use a restriction enzyme digest procedure (fingerprinting procedure) to place the clones into types. The primary focus of the research carried out during this report period was twofold: (a) to complete the sequencing of the clones, and (b) to analyze the clone sequences phylogenetically in order to determine the relatedness of the bacteria detected in the samples to each other and to previously described genera and species.

Technical-tactical analysis of youth olympic taekwondo combat.

Science.gov (United States)

Tornello, Francesco; Capranica, Laura; Minganti, Carlo; Chiodo, Salvatore; Condello, Giancarlo; Tessitore, Antonio

2014-04-01

The purpose of this study was to define the technical and tactical profiles of official youth taekwondo competitions played under the most recent rules of the International Taekwondo Federation. Tactical actions (i.e., attack, defense, and block), technical executions (from 1- to 4-point scores), kicking legs (i.e., front/rear and right/left), and overall technical effectiveness were investigated in relation to match outcome of semifinal and final competitions (n = 50) of youth (aged 13-14 years) black belt athletes during the Italian Taekwondo Cadet Championship. Differences (p technical exchanges showed differences (p technical executions. Winners resulted more efficient (p technical and tactical variables. In general, these findings showed that Cadets tend to adopt an offensive strategy. In considering that the adoption of the new electronic system requires athletes to execute correct technical actions to have a score assigned, coaches should emphasize the effectiveness of scoring techniques and help athletes to effectively improve their defense and counterattack capabilities.

Astrobee Periodic Technical Review (PTR) Delta 3

Science.gov (United States)

Provencher, Christopher; Smith, Marion F.; Smith, Ernest Everett; Bualat, Maria Gabriele; Barlow, Jonathan Spencer

2017-01-01

Astrobee is a free flying robot for the inside of the International Space Station (ISS). The Periodic Technical Review (PTR) delta 3 is the final design review of the system presented to stakeholders.

Liver CT image processing: a short introduction of the technical elements.

Science.gov (United States)

Masutani, Y; Uozumi, K; Akahane, Masaaki; Ohtomo, Kuni

2006-05-01

In this paper, we describe the technical aspects of image analysis for liver diagnosis and treatment, including the state-of-the-art of liver image analysis and its applications. After discussion on modalities for liver image analysis, various technical elements for liver image analysis such as registration, segmentation, modeling, and computer-assisted detection are covered with examples performed with clinical data sets. Perspective in the imaging technologies is also reviewed and discussed.

Liver CT image processing: A short introduction of the technical elements

International Nuclear Information System (INIS)

Masutani, Y.; Uozumi, K.; Akahane, Masaaki; Ohtomo, Kuni

2006-01-01

In this paper, we describe the technical aspects of image analysis for liver diagnosis and treatment, including the state-of-the-art of liver image analysis and its applications. After discussion on modalities for liver image analysis, various technical elements for liver image analysis such as registration, segmentation, modeling, and computer-assisted detection are covered with examples performed with clinical data sets. Perspective in the imaging technologies is also reviewed and discussed

FINAL TECHNICAL REPORT: 20% Wind by 2030: Overcoming the Challenges

Energy Technology Data Exchange (ETDEWEB)

Tom Kaiserski; Dan Lloyd

2012-02-28

The funds allocated through the Wind Powering America (WPA) grant were utilized by the State of Montana to support broad outreach activities communicating the benefits and opportunities of increased wind energy and transmission development. The challenges to increased wind development were also clearly communicated with the understanding that a clearer comprehension of the challenges would be beneficial in overcoming the obstacles to further development. The ultimate purpose of these activities was to foster the increased development of Montana's rich wind resources through increased public acceptance and wider dissemination of technical resources.

Final Technical Report for subcontract number B612144

Energy Technology Data Exchange (ETDEWEB)

Mayali, X. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marcu, O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-11

The original statement of work stipulated that the Subcontractor shall perform bacterial and algal cultivation and manipulation, microbe isolation, preparation of samples for sequencing and isotopic analysis, data analysis, and manuscript preparation. The Subcontractor shall work closely with Dr. Mayali and other LLNL scientists, and shall participate in monthly SFA meetings (either in person or by telephone). The Subcontractor shall deliver a final report at the conclusion of the work.

Technical requirements on knowledge base and instrumentation system for decision making in plant operation and maintenance

International Nuclear Information System (INIS)

Kitamura, Masaharu; Yoshikawa, Shinji; Hasegawa, Makoto

1998-03-01

A series of technical surveys and studies are described in this report to examine and identify technical requirements to be posed on knowledge base and instrumentation system as the fundamental in high reliability computational decision making in operation and maintenance of nuclear power plants. Monitoring and diagnosis are focused as the important tasks among the operation/maintenance-related tasks. A concrete monitoring and diagnosis system configuration has been proposed consisting of distributed symptom database and of on-demand measurement subsystem. An prototype of the proposed system configuration has been successfully verified. (author)

Final Scientific/Technical Report for award DE-FC--07-00AL67053

International Nuclear Information System (INIS)

Dixon, Cathy

2005-01-01

The project ''Creating an Educational Consortium to Support the Recruitment and Retention of Expertise for the Nuclear Weapons Complex'' was also known as the Advanced Fuel Cycle Initiative (AFCI) University Fellowship Program. Since its inception, the Advanced Fuel Cycle Initiative program and its predecessor, the Advanced Accelerator Applications (AAA) program, have engaged university researchers and students in the sciences necessary to answer technical questions related to reducing high-level waste volumes, optimizing the economics and performance of Yucca Mountain, reducing the technical need for a second repository, reducing the long-term inventories of plutonium in spent fuel, and enabling the proliferation-resistant recovery of the energy contained in spent fuel. The Advanced Fuel Cycle University Fellowship Program is intended to support top students across the nation in a variety of disciplines that will be required to support transmutation research and technology development in the coming decades

Basic concepts for crew resource management and non-technical skills.

Science.gov (United States)

Flin, Rhona; Maran, Nikki

2015-03-01

In this paper, we explain the conceptual background to non-technical skills and show how they can influence job performance in anaesthesia. We then describe the taxonomy of anaesthetists' non-technical skills (ANTS) and related systems, such as ANTS-AP for anaesthetic practitioners. We discuss the training courses that have been designed to teach these non-technical skills, which are called crew resource management (CRM), crisis resource management (CRM) or crisis avoidance resource management (CARMA). Finally, we discuss the application of non-technical skills assessment systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Reeder, Richard [Stony Brook Univ., NY (United States); Phillips, Brian [Stony Brook Univ., NY (United States)

2017-10-18

A variety of calcifying organisms produce a transient or metastable amorphous calcium carbonate (ACC) precursor phase that is assembled and subsequently transformed into a crystalline biomineral, typically calcite or aragonite. The complex shapes, hierarchical structures, and unique physical properties of the biominerals that result from this calcification pathway have stimulated interest in adapting these concepts for the design and creation of bio-inspired functional materials in the laboratory. ACC also forms as a reactive precursor in diverse inorganic systems and is likely to play a much broader role in calcium carbonate formation. Knowledge of the structure, composition, and behavior of this metastable phase is critical for establishing a structural and mechanistic framework for calcium carbonate formation and its role in biogeochemical processes, including carbon cycling. Minor additives, such as magnesium, phosphorus, and organic macromolecules, are known to play important roles in controlling ACC stability, transformation kinetics, and selection of final crystalline polymorph. Molecular water also occurs in many types of ACC and is thought to play a structural role in its stability and transformation behavior. One of the major challenges that remain unresolved is identification of the structural basis for the role of these minor additives and molecular water. The absence of long-range order in ACC, and other amorphous phases, has posed a challenge for study by techniques commonly used for crystalline solids. Preliminary studies in our group show that the combination of two techniques, synchrotron X-ray-based pair distribution function (PDF) analysis and nuclear magnetic resonance (NMR) spectroscopy can provide entirely new insight to structural properties of synthetic ACC over length scales that are most relevant for understanding its transformation properties. Building on preliminary experiments, we propose a systematic study of synthesis, structure, and

CT pulmonary angiography of adult pulmonary vascular diseases: Technical considerations and interpretive pitfalls

International Nuclear Information System (INIS)

Taslakian, Bedros; Latson, Larry A.; Truong, Mylene T.; Aaltonen, Eric; Shiau, Maria C.; Girvin, Francis; Alpert, Jeffrey B.; Wickstrom, Maj; Ko, Jane P.

2016-01-01

Highlights: • CTPA plays a key role in the evaluation of pulmonary vascular diseases. • Improvements in CT technology have improved visualization of pulmonary arteries. • Knowledge of the technical pitfalls is essential for accurate diagnosis. • Dual energy CT imaging enables parenchymal iodine evaluation. • An awareness of the entities affecting the pulmonary arteries is important. - Abstract: Computed tomography pulmonary angiography (CTPA) has become the primary imaging modality for evaluating the pulmonary arteries. Although pulmonary embolism is the primary indication for CTPA, various pulmonary vascular abnormalities can be detected in adults. Knowledge of these disease entities and understanding technical pitfalls that can occur when performing CTPA are essential to enable accurate diagnosis and allow timely management. This review will cover a spectrum of acquired abnormalities including pulmonary embolism due to thrombus and foreign bodies, primary and metastatic tumor involving the pulmonary arteries, pulmonary hypertension, as well as pulmonary artery aneurysms and stenoses. Additionally, methods to overcome technical pitfalls and interventional treatment options will be addressed.

CT pulmonary angiography of adult pulmonary vascular diseases: Technical considerations and interpretive pitfalls

Energy Technology Data Exchange (ETDEWEB)

Taslakian, Bedros, E-mail: bedros.taslakian@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Latson, Larry A., E-mail: larry.latson@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Truong, Mylene T., E-mail: mtruong@mdanderson.org [Department of Radiology, University of Texas, MD Anderson Cancer Center, TX (United States); Aaltonen, Eric, E-mail: Eric.Aaltonen@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Shiau, Maria C., E-mail: Maria.Shiau@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Girvin, Francis, E-mail: Francis.Girvin@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Alpert, Jeffrey B., E-mail: Jeffrey.Alpert@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Wickstrom, Maj, E-mail: Maj.Wickstrom@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States); Ko, Jane P., E-mail: Jane.Ko@nyumc.org [Department of Radiology, NYU Langone Medical Center, NY (United States)

2016-11-15

Highlights: • CTPA plays a key role in the evaluation of pulmonary vascular diseases. • Improvements in CT technology have improved visualization of pulmonary arteries. • Knowledge of the technical pitfalls is essential for accurate diagnosis. • Dual energy CT imaging enables parenchymal iodine evaluation. • An awareness of the entities affecting the pulmonary arteries is important. - Abstract: Computed tomography pulmonary angiography (CTPA) has become the primary imaging modality for evaluating the pulmonary arteries. Although pulmonary embolism is the primary indication for CTPA, various pulmonary vascular abnormalities can be detected in adults. Knowledge of these disease entities and understanding technical pitfalls that can occur when performing CTPA are essential to enable accurate diagnosis and allow timely management. This review will cover a spectrum of acquired abnormalities including pulmonary embolism due to thrombus and foreign bodies, primary and metastatic tumor involving the pulmonary arteries, pulmonary hypertension, as well as pulmonary artery aneurysms and stenoses. Additionally, methods to overcome technical pitfalls and interventional treatment options will be addressed.

Final Technical Report: "Achieving Regional Energy Efficiency Potential in the Southeast”

Energy Technology Data Exchange (ETDEWEB)

Mahoney, Mandy [Southeast Energy Efficiency Alliance (SEEA), Atlanta, GA (United States)

2018-03-07

The overall objective of this award was to facilitate sharing of DOE resources and best practices as well as provide technical assistance to key stakeholders to support greater compliance with energy efficiency standards and increased energy savings. The outcomes of this award include greater awareness among key stakeholders on energy efficiency topics, increased deployment and utilization of DOE resources, and effective policies and programs to support energy efficiency in the Southeast.

Assessing the Impact of Imperfect Diagnosis on Service Reliability

DEFF Research Database (Denmark)

Grønbæk, Lars Jesper; Schwefel, Hans-Peter; Kjærgaard, Jens Kristian

2010-01-01

, representative diagnosis performance metrics have been defined and their closed-form solutions obtained for the Markov model. These equations enable model parameterization from traces of implemented diagnosis components. The diagnosis model has been integrated in a reliability model assessing the impact...... of the diagnosis functions for the studied reliability problem. In a simulation study we finally analyze trade-off properties of diagnosis heuristics from literature, map them to the analytic Markov model, and investigate its suitability for service reliability optimization....

ITER technical basis

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-01-01

Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties.

ITER technical basis

International Nuclear Information System (INIS)

2002-01-01

Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties

Final Scientific/Technical Report Solar America Initiative: Solar Outreach and Communications

Energy Technology Data Exchange (ETDEWEB)

Weissman, Jane M

2011-09-10

The purpose of the Solar America Initiative: Solar Outreach and Communications grant was to promote better communications among stakeholders; address infrastructure barriers to solar energy; and coordinate with industry, the U.S. Department of Energy, national laboratories, states, cities and counties. The Interstate Renewable Energy Council (IREC), a non-profit organization formed in 1982, approached this grant project by establishing a wide range of communication and outreach activities including newsletters, workshops, webinars, model practices and publications; by advancing easy and fair hook-up rules to the utility grid; and by upgrading training based on industry competency standards. The Connecting to the Grid project and the Solar Codes and Standards Public Hearings project offered communication coupled with technical assistance to overcome interconnection, net metering and other regulatory and program barriers. The Workforce Development Project tackled building a strong workforce through quality training and competency assessment programs. IREC's web site, the semi-monthly state and stakeholder newsletter and the metrics report resulted in better communications among stakeholders. Workshops and phone seminars offered technical assistance and kept stakeholders up-to-date on key issues. All of these activities resulted in implementing sustainable solutions to institutional and market barriers to solar energy and getting the right information to the right people.

FINAL TECHNICAL REPORT Chagas Prevention in Central America

International Development Research Centre (IDRC) Digital Library (Canada)

Carlota Monroy

INFORME FINAL: PROYECTO ID 106531 - 001. CORRESPONDIENTE AL PERIODO DEL 1 DE MARZO 2011 AL 31 DE MARZO 2014. CONTENIDO. 1. Información general ……………………………………………………………1. 2. Resumen del proyecto ………………………………………………………….2. 3. Metas objetivos ...

AISI Direct Steelmaking Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Aukrust, E.

1994-08-01

This final report deals with the results of a 5-yr project for developing a more energy-efficient, environmentally friendly, less costly process for producing hot metal than current coke ovens and blast furnaces. In the process, iron ore pellets are smelted in a foamy slag created by reaction of coal char with molten slag to produce CO. The CO further reacts with oxygen, which also reacts with coal volatile matter, to produce the heat necessary to sustain the endothermic reduction reaction. The uncombusted CO and H{sub 2} from the coal are used to preheat and prereduce hematite pellets for the most efficient use of the energy in the coal. Laboratory programs confirmed that the process steps worked. Pilot plant studies were successful. Economic analysis for a 1 million tpy plant is promising.

TECHNICAL AND ORGANIZATIONAL IMPROVEMENTS OF PACKAGING PRODUCTION PROCESS

Directory of Open Access Journals (Sweden)

Anna Rudawska

2016-06-01

Full Text Available Due to customer driven economies, today’s world markets are characterized by high fluctuations in market demand and the frequent arrival of new technologies and new products. To stay competitive in such markets manufacturing companies require continuous improvements both in technical and organizational areas of their activity. The paper presents results of the diagnosis provided in the manufacturing area of the company producing cardboard packages and recommendations to make the production process more efficient. Especially, among the proposed technical and organizational recommendations the most important ones are: automation of certain elements of the production process and changes in production plant layout.

National Alliance for Advanced Biofuels and Bio-Products Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olivares, Jose A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Baxter, Ivan [US Dept. of Agriculture (USDA)., Washington, DC (United States); Brown, Judith [Univ. of Arizona, Tucson, AZ (United States); Carleton, Michael [Matrix Genetics, Seattle, WA (United States); Cattolico, Rose Anne [Univ. of Washington, Seattle, WA (United States); Taraka, Dale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Detter, John C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Devarenne, Timothy P. [Texas Agrilife Research, College Station, TX (United States); Dutcher, Susan K. [Washington Univ., St. Louis, MO (United States); Fox, David T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Goodenough, Ursula [Washington Univ., St. Louis, MO (United States); Jaworski, Jan [Donald Danforth Plant Science Center, St. Louis, MO (United States); Kramer, David [Michigan State Univ., East Lansing, MI (United States); Lipton, Mary S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCormick, Margaret [Matrix Genetics, Seattle, WA (United States); Merchant, Sabeeha [Univ. of California, Los Angeles, CA (United States); Molnar, Istvan [Univ. of Arizona, Tucson, AZ (United States); Panisko, Ellen A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pellegrini, Matteo [Univ. of California, Los Angeles, CA (United States); Polle, Juergen [City Univ. (CUNY), NY (United States). Brooklyn College; Sabarsky, Martin [Cellana, Inc., San Diego, CA (United States); Sayre, Richard T. [New Mexico Consortium, Los Alamos, NM (United States); Starkenburg,, Shawn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stormo, Gary [Washington Univ., St. Louis, MO (United States); Twary, Scott N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Clifford J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Pat J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Yuan, Joshua S. [Texas Agrilife Research, College Station, TX (United States); Arnold, Bob [Univ. of Arizona, Tucson, AZ (United States); Bai, Xuemei [Cellana, Inc., San Diego, CA (United States); Boeing, Wiebke [New Mexico State Univ., Las Cruces, NM (United States); Brown, Lois [Texas Agrilife Research, College Station, TX (United States); Gujarathi, Ninad [Reliance Industries Limited, Mumbai (India); Huesemann, Michael [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lammers, Pete [New Mexico State Univ., Las Cruces, NM (United States); Laur, Paul [Eldorado Biofuels, Santa Fe, NM (United States); Khandan, Nirmala [New Mexico State Univ., Las Cruces, NM (United States); Parsons, Ronald [Solix BioSystems, Fort Collins, CO (United States); Samocha, Tzachi [Texas Agrilife Research, College Station, TX (United States); Thomasson, Alex [Texas Agrilife Research, College Station, TX (United States); Unc, Adrian [New Mexico State Univ., Las Cruces, NM (United States); Waller, Pete [Univ. of Arizona, Tucson, AZ (United States); Bonner, James [Clarkson Univ., Potsdam, NY (United States); Coons, Jim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fernando, Sandun [Texas Agrilife Research, College Station, TX (United States); Goodall, Brian [Valicor Renewables, Dexter, MI (United States); Kadam, Kiran [Valicor Renewables, Dexter, MI (United States); Lacey, Ronald [Texas Agrilife Research, College Station, TX (United States); Wei, Liu [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Marrone, Babs [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nikolov, Zivko [Texas Agrilife Research, College Station, TX (United States); Trewyn, Brian [Colorado School of Mines, Golden, CO (United States); Albrecht, Karl [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Capareda, Sergio [Texas Agrilife Research, College Station, TX (United States); Cheny, Scott [Diversified Energy, Gilbert, AZ (United States); Deng, Shuguang [New Mexico State Univ., Las Cruces, NM (United States); Elliott, Douglas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cesar, Granda [Terrabon, LLC, Bryan, TX (United States); Hallen, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lupton, Steven [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Lynch, Sharry [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Marchese, Anthony [Colorado State Univ., Fort Collins, CO (United States); Nieweg, Jennifer [Albemarle Catilin, Ames, IA (United States); Ogden, Kimberly [Univ. of Arizona, Tucson, AZ (United States); Oyler, James [Genifuel, Salt Lake City, UT (United States); Reardon, Ken [Colorado State Univ., Fort Collins, CO (United States); Roberts, William [North Carolina State Univ., Raleigh, NC (United States); Sams, David [Albemarle Catilin, Ames, IA (United States); Schaub, Tanner [New Mexico State Univ., Las Cruces, NM (United States); Silks, Pete [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Archibeque, Shawn [Colorado State Univ., Fort Collins, CO (United States); Foster, James [Texas Agrilife Research, College Station, TX (United States); Gaitlan, Delbert [Texas Agrilife Research, College Station, TX (United States); Lawrence, Addison [Texas Agrilife Research, College Station, TX (United States); Lodge-Ivey, Shanna [New Mexico State Univ., Las Cruces, NM (United States); Wickersham, Tyron [Texas Agrilife Research, College Station, TX (United States); Blowers, Paul [Univ. of Arizona, Tucson, AZ (United States); Davis, Ryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Downes, C. Meghan [New Mexico State Univ., Las Cruces, NM (United States); Dunlop, Eric [Pan Pacific Technologies Pty. Ltd., Adelaide (Australia); Frank, Edward [Argonne National Lab. (ANL), Argonne, IL (United States); Handler, Robert [Michigan Technological Univ., Houghton, MI (United States); Newby, Deborah [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pienkos, Philip [National Renewable Energy Lab. (NREL), Golden, CO (United States); Richardson, James [Texas Agrilife Research, College Station, TX (United States); Seider, Warren [Univ. of Pennsylvania, Philadelphia, PA (United States); Shonnard, David [Michigan Technological Univ., Houghton, MI (United States); Skaggs, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-30

The main objective of NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. The approach was to address technology development across the entire value chain of algal biofuels production, from selection of strains to cultivation, harvesting, extraction, fuel conversion, and agricultural coproduct production. Sustainable practices and financial feasibility assessments ununderscored the approach and drove the technology development.

76 FR 4645 - Hydrogen and Fuel Cell Technical Advisory Committee (HTAC)

Science.gov (United States)

2011-01-26

... DEPARTMENT OF ENERGY Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) AGENCY: Department...: This notice announces a meeting of the Hydrogen and Fuel Cell Technical Advisory Committee (HTAC). HTAC... Agenda: (Subject to change; updates will be posted on http://hydrogen.energy.gov and copies of the final...

76 FR 60478 - Hydrogen and Fuel Cell Technical Advisory Committee (HTAC)

Science.gov (United States)

2011-09-29

... DEPARTMENT OF ENERGY Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) AGENCY: Department...: The Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) was established under section 807 of... website at: http://hydrogen.energy.gov and copies of the final agenda will available the date of the...

International Standards Development for Marine and Hydrokinetic Renewable Energy - Final Report on Technical Status

Energy Technology Data Exchange (ETDEWEB)

Rondorf, Neil E.; Busch, Jason; Kimball, Richard

2011-10-29

This report summarizes the progress toward development of International Standards for Marine and Hydrokinetic Renewable Energy, as funded by the U.S. Department of Energy (DOE) under the International Electrotechnical Commission (IEC) Technical Committee 114. The project has three main objectives: 1. Provide funding to support participation of key U.S. industry technical experts in 6 (originally 4) international working groups and/or project teams (the primary standards-making committees) and to attend technical meetings to ensure greater U.S. involvement in the development of these standards. 2. Provide a report to DOE and industry stakeholders summarizing the IEC standards development process for marine and hydrokinetic renewable energy, new international standards and their justifications, and provide standards guidance to industry members. 3. Provide a semi-annual (web-based) newsletter to the marine renewable energy community. The newsletter will educate industry members and stakeholders about the processes, progress, and needs of the US efforts to support the international standards development effort. The newsletter is available at www.TC114.us

Final Scientific Technical Report Crowder College MARET Center

Energy Technology Data Exchange (ETDEWEB)

Boyt, Art [Crowder College, Neosho, MO (United States); Eberle, Dan [Crowder College, Neosho, MO (United States); Hudson, Pam [Crowder College, Neosho, MO (United States); Hopper, Russ [Crowder College, Neosho, MO (United States)

2013-06-30

, exploring and validating new applications of solar and other renewable technologies, the MARET Facility will house a wide variety of programs which will advance implementation of renewable energy throughout the region. These program goals include; Curriculum in renewable energy for pre-engineering transfer programs; Certification and degree programs for technical degrees for Energy Efficiency, Wind, Photovoltaic and Solar Thermal professionals; Short courses and workshops for building management and design professionals; Public education and demonstration projects in renewable energy through conferences and K-12 educational outreach; Technical degree offering in building construction incorporating “best practices” for energy efficiency and renewables; and Business incubators for new renewable energy businesses and new product development The new MARET facility will support the mission of the US Department of Energy (DOE) Solar Program, “to improve America’s security, environmental quality, and economic prosperity through public-private partnerships that bring reliable and affordable solar energy technologies to the marketplace,” through a variety of educational and business assistance programs. Further, technical innovations planned for the MARET facility and its applied research activities will advance the Solar Program strategic goals to “reduce the cost of solar energy to the point it becomes competitive in relevant energy markets (e.g., buildings, power plants) and for solar technology to enable a sustainable solar industry.” Overarching Goals relative to program needs, future expansion, flexibility, quality of materials, and construction and operational costs:; Experimental: The structure and systems of the building operate as an educational resource. The systems are meant to be a source for data collection and study for building users and instructors; Educational: Part of the evolution of this building and its ongoing goals is to use the building as an

Impacto de la capacitación en la mejora continua de la calidad del diagnóstico citológico The effect of technical training for the continuous improvement of the quality in cytological diagnosis

Directory of Open Access Journals (Sweden)

Miguel Angel Herrera Pérez

2010-03-01

Full Text Available Los indicadores generales de la eficacia en los programas de prevención del cáncer cervical se mantienen altos en nuestro país. Objetivos: Evaluar el impacto de la capacitación técnica en la mejora continua del diagnóstico citológico del cuello uterino en el Hospital "Abel Santamaría Cuadrado", período 2005-2007. Diseño: Se realizó un estudio de intervención-acción para medir el efecto de la capacitación en la calidad del diagnóstico de los citotecnólogos, medido mediante la correlación entre un primer diagnóstico emitido por el personal técnico y un segundo por un especialista en Anatomía Patológica, de una muestra de 22864 citologías. Se utilizaron las variables de concordancia en general y por el tipo de lesión, y aplicó la estadística descriptiva para variables cualitativas categóricas, expresadas en frecuencias absolutas y relativas porcentuales. Las comparaciones de frecuencias se verificaron mediante el estadígrafo de Ji cuadrado al 95 % de confianza y la prueba de kappa para la correlación entre observadores. Resultados. Se encontró un incremento de la concordancia en el 2007 con relación al periodo 2005-2006, resultado altamente significativo (X² = 75.0; gdl = 1; p = 0.00000001. La concordancia de acuerdo al diagnóstico se incrementó con la excepción del NIC-III. Conclusión. Se comprobó que la capacitación influyó en la mejoría continua de la calidad del diagnóstico citológico.In our country general indicators to assess the effectiveness of Programs for the Prevention of Cervical Cancer keep high. Objectives: To evaluate the effects of the technical training for the continuous improvement of cytological diagnosis of the cervical cancer at "Abel Santamaria Cuadrado" University Hospital, during 2005-2007. Design: An intervention-action research was conducted in order to assess the effectiveness of the technical training process for improving quality in the diagnosis performed by the technicians of

Nonculture molecular techniques for diagnosis of bacterial disease in animals: a diagnostic laboratory perspective.

Science.gov (United States)

Cai, H Y; Caswell, J L; Prescott, J F

2014-03-01

The past decade has seen remarkable technical advances in infectious disease diagnosis, and the pace of innovation is likely to continue. Many of these techniques are well suited to pathogen identification directly from pathologic or clinical samples, which is the focus of this review. Polymerase chain reaction (PCR) and gene sequencing are now routinely performed on frozen or fixed tissues for diagnosis of bacterial infections of animals. These assays are most useful for pathogens that are difficult to culture or identify phenotypically, when propagation poses a biosafety hazard, or when suitable fresh tissue is not available. Multiplex PCR assays, DNA microarrays, in situ hybridization, massive parallel DNA sequencing, microbiome profiling, molecular typing of pathogens, identification of antimicrobial resistance genes, and mass spectrometry are additional emerging technologies for the diagnosis of bacterial infections from pathologic and clinical samples in animals. These technical advances come, however, with 2 caveats. First, in the age of molecular diagnosis, quality control has become more important than ever to identify and control for the presence of inhibitors, cross-contamination, inadequate templates from diagnostic specimens, and other causes of erroneous microbial identifications. Second, the attraction of these technologic advances can obscure the reality that medical diagnoses cannot be made on the basis of molecular testing alone but instead through integrated consideration of clinical, pathologic, and laboratory findings. Proper validation of the method is required. It is critical that veterinary diagnosticians understand not only the value but also the limitations of these technical advances for routine diagnosis of infectious disease.

The role of non-technical skills in surgery

Directory of Open Access Journals (Sweden)

Riaz A. Agha

2015-12-01

This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care.

Technical program plan for the transitioning, decommissioning, and final disposition focus area

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Hundreds of aging nuclear materials processing facilities within the Department of Energy`s (DOE) Weapons Complex are now being shut down and deactivated. These facilities, situated throughout the United States, will require a monumental effort to clean up safely and with minimal environmental insult. Current cleanup technologies tend to be labor intensive and expensive, they produce an unacceptably large volume of waste, and they expose workers to radioactive and other hazardous substances. This document describes an emerging program designed to develop and demonstrate new technical approaches to the decontamination and decommissioning (D&D) program for DOE`s nuclear materials processing facilities. Sponsored by the DOE Office of Technology Development within the Office of Environmental Restoration and Waste Management (EM), the program seeks to integrate the strengths of DOE`s technical, managerial, and systems engineering capabilities with those of industry, universities, and other government agencies. Once developed, these technologies will help to provide US industry with a competitive edge in the worldwide market that exists for improved environmental restoration and D&D services.

Final report of the UMTRA independent technical review of TAC audit programs

International Nuclear Information System (INIS)

1994-10-01

This report details the findings of an Independent Technical Review (ITR) of practices and procedures for the Uranium Mill Tailings Remedial Action (UMTRA) Project audit program. The audit program is conducted by Jacobs Engineering Group Inc., the Technical Assistance Contractor (TAC) for the UMTRA Project. The purpose of the ITR was to ensure that the TAC audit program is effective and is conducted efficiently. The ITR was conducted from May 16-20, 1994. A review team observed audit practices in the field, reviewed the TAC audit program's documentation, and discussed the program with TAC staff and management. The format of this report has been developed around EPA guidelines; they comprise most of the major section headings. Each section begins by identifying the criteria that the TAC program is measured against, then describing the approach used by the ITR team to measure each TAC audit program against the criteria. An assessment of each type of audit is then summarized for each component in the following order: Radiological audit summary; Health and safety audit summary; Environmental audit summary; Quality assurance audit summary

Technical program plan for the transitioning, decommissioning, and final disposition focus area

International Nuclear Information System (INIS)

1994-01-01

Hundreds of aging nuclear materials processing facilities within the Department of Energy's (DOE) Weapons Complex are now being shut down and deactivated. These facilities, situated throughout the United States, will require a monumental effort to clean up safely and with minimal environmental insult. Current cleanup technologies tend to be labor intensive and expensive, they produce an unacceptably large volume of waste, and they expose workers to radioactive and other hazardous substances. This document describes an emerging program designed to develop and demonstrate new technical approaches to the decontamination and decommissioning (D ampersand D) program for DOE's nuclear materials processing facilities. Sponsored by the DOE Office of Technology Development within the Office of Environmental Restoration and Waste Management (EM), the program seeks to integrate the strengths of DOE's technical, managerial, and systems engineering capabilities with those of industry, universities, and other government agencies. Once developed, these technologies will help to provide US industry with a competitive edge in the worldwide market that exists for improved environmental restoration and D ampersand D services

Parotid Duct Repair with Intubation Tube: Technical Note

Science.gov (United States)

Öztürk, Muhammed Beşir; Barutca, Seda Asrufoğlu; Keskin, Elif Seda; Atik, Bekir

2017-01-01

The parotid duct can be damaged in traumatic injuries and surgical interventions. Early diagnosis and treatment of a duct injury is of great importance because complications such as sialocele and salivary gland fistula may develop if the duct is not surgically repaired. We think the cuff of an intubation tube is an ideal material in parotid duct repair, because of its technical characteristics, easiness of availability, and low-cost. In this paper, we described the use of the cuff cannula of an intubation tube for the diagnosis and treatment of parotid duct laceration, as a low-cost and easy to access material readily available in every operating room. PMID:28713751

Technical writing versus technical writing

Science.gov (United States)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Technical procedures for utilities and solid waste: Environmental Field Program, Deaf Smith County site, Texas: Final draft

International Nuclear Information System (INIS)

1987-08-01

The evaluation of environmental issues and concerns and the addressing of statutory requirements are fundamental parts in the characterization of the site in Deaf Smith County, Texas for the US Department of Energy's Salt Repository Project (SRP). To ensure that the environmental field program comprehensively addresses the issues and requirements of the project, a site study plan (SSP) has been prepared for Utilities and Solid Waste considerations. This technical procedure (TP) has been developed to implement the field program described in the Utilities and Solid Waste Site Study Plan. The purpose and scope of the Utilities and Solid Waste Technical Procedure is to develop and implement a data collection procedure to fulfill the data base needs of the Utilities and Solid Waste SSP. The procedure describes a method of obtaining, assessing and verifying the capabilities of the regional service utilities and disposal contractors. This data base can be used to identify a preferred service source for the engineering contractor. The technical procedure was produced under the guidelines established in Technical Administrative Procedure No. 1.0, Preparation, Review and Approval of Technical Procedures

Diagnosis of antenatal Bartter syndrome.

Science.gov (United States)

Narayan, R; Peres, M; Kesby, G

2016-01-01

Bartter syndrome is a rare heterogeneous group of autosomal-recessive salt-losing renal tubular disorders that can present in fetal life (antenatal Bartter syndrome; ABS) as "unexplained" early-onset polyhydramnios, often associated with growth restriction. Prenatal diagnosis of the condition involves assessment of amniotic fluid biochemistry in a setting of polyuric polyhydramnios; with elevated chloride levels considered a consistent and diagnostic finding. Other amniotic fluid biochemical markers have been described, notably increased aldosterone levels, and low total protein levels. NOVEL INSIGHT: Antenatal Bartter syndrome is a heterogeneous group of renal disorders. While certain biochemical features in amniotic fluid might heighten suspicion, final diagnosis can only be made in the postnatal setting. In the setting of unexplained severe polyhydramnios, clinicians should continue to entertain the diagnosis of antenatal Bartter Syndrome and maintain neonatal surveillance, even if amniotic fluid markers do not support the diagnosis.

Radiological diagnosis in traumatology

International Nuclear Information System (INIS)

Frahm, R.

2001-01-01

This loose-leaf publication covers all radiological problems that may possibly occur in accident surgery. The focus is on conventional radiological diagnosis. The physical and technical fundamentals of diagnostic examination methods are discussed, followed by practical hints on radiation protection, technical equipment and quality assurance, as well as accurate information on the procedure of taking and interpreting standard X-ray pictures. The indications for standard X-raying, tomography, CT and MRT are presented in consideration of the radiation exposure incurred by the patient. The reader is also informed on the dynamics and varying morphology of bone fracture healing, potential disturbances of callus formation and reconstruction, as well as on possible complications. The main section of the book discusses injuries of the skull, spinal cord, pectoral girdle, upper arm, elbow and lower arm, wrist and hands, pelvis, hip joint, knee and upper and lower leg, ankle joint and foot, thorax and abdomen. (orig.)

Transvaginal Ultrasound for the Diagnosis of Abnormal Uterine Bleeding.

Science.gov (United States)

Wheeler, Karen C; Goldstein, Steven R

2017-03-01

Transvaginal ultrasound is the first-line imaging test for the evaluation of abnormal uterine bleeding in both premenopausal and postmenopausal women. Transvaginal ultrasound can be used to diagnose structural causes of abnormal bleeding such as polyps, adenomyosis, leiomyomas, hyperplasia, and malignancy, and can also be beneficial in making the diagnosis of ovulatory dysfunction. Traditional 2-dimensional imaging is often enhanced by the addition of 3-dimension imaging with coronal reconstruction and saline infusion sonohysterography. In this article we discuss specific ultrasound findings and technical considerations useful in the diagnosis of abnormal uterine bleeding.

KBS Technical report 1-120 (1977-1978). Summaries

International Nuclear Information System (INIS)

1979-05-01

The Swedish nuclear utilities started early in 1977 the KBS (nuclear fuel safety) project to study the high level waste problem and report on how and where a safe final storage could be arranged in Sweden. The docummentation produced by the project during 1977 and 1978 has been collected in a series of technical reports numbered from 1 to 120. The English summaries of the technical reports have been collected in this separate volume, No. 121. (G.B.)

Specified radioactive waste final disposal act

International Nuclear Information System (INIS)

Yasui, Masaya

2001-01-01

Radioactive wastes must be finally and safely disposed far from human activities. Disposal act is a long-range task and needs to be understood and accepted by public for site selection. This paper explains basic policy of Japanese Government for final disposal act of specified radioactive wastes, examination for site selection guidelines to promote residential understanding, general concept of multi-barrier system for isolating the specific radioactive wastes, and research and technical development for radioactive waste management. (S. Ohno)

Routine clinical use of circulating tumor cells for diagnosis of mutations and chromosomal rearrangements in non-small cell lung cancer-ready for prime-time?

Science.gov (United States)

Pailler, Emma; Faugeroux, Vincent; Oulhen, Marianne; Catelain, Cyril; Farace, Françoise

2017-08-01

In non-small cell lung cancer (NSCLC), diagnosis of predictive biomarkers for targeted therapies is currently done in small tumor biopsies. However, tumor biopsies can be invasive, in some cases associated with risk, and tissue adequacy, both in terms of quantity and quality is often insufficient. The development of efficient and non-invasive methods to identify genetic alterations is a key challenge which circulating tumor cells (CTCs) have the potential to be exploited for. CTCs are extremely rare and phenotypically diverse, two characteristics that impose technical challenges and impact the success of robust molecular analysis. Here we introduce the clinical needs in this disease that mainly consist of the diagnosis of epidermal growth factor receptor ( EGFR ) activating alterations and anaplastic lymphoma kinase ( ALK ) rearrangement. We present the proof-of-concept studies that explore the detection of these genetic alterations in CTCs from NSCLC patients. Finally, we discuss steps that are still required before CTCs are routinely used for diagnosis of EGFR -mutations and ALK -rearrangements in this disease.

Does the medical diagnosis of occupational asthma coincide with the legal diagnosis?

Science.gov (United States)

Çelebi Sözener, Zeynep; Aydın, Ömür; Demirel, Yavuz Selim; Soyyiğit, Şadan; Çerçi, Pamir; Kendirlinan, Reşat; Bavbek, Sevim; Çelik, Gülfem Elif; Misirligil, Zeynep; Sin, Betül Ayşe; Keleşoğlu, Arif; Mungan, Dilşad

2017-11-01

The incidence of occupational asthma (OA) is increasing worldwide. In this study, we first aimed to document the rate of diagnosis of OA among patients who were referred to our clinic from the Social Security Institution and the factors that affected diagnosis; secondly, we aimed to assess the consistency of the medical and legal diagnoses. The study involved 132 consecutive patients who were referred to our clinic for the evaluation of OA between 2010 and 2015. Detailed workplace history, the tools used in the diagnosis such as peak expiratory flow (PEF) monitoring and bronchial provocation tests, and the final medical diagnosis were recorded from case files. Asthma was diagnosed in 75% (n = 99) of the patients. Among them, 22.2% were diagnosed as having OA. The diagnosis was confirmed by serial PEF measurements, non-specific bronchial hyperreactivity assessment or both of the tests both at work and off-work periods. OA diagnosis was mostly established in active workers (72.7%). The legal diagnosis period was completed in 54.5% of these 22 patients, and 50% (n = 11) were officially diagnosed as having OA with a 91.6% concordance with medical diagnosis. This study verifies the importance of diagnosing asthma correctly as a first step in the evaluation of OA. Diagnostic tests other than specific provocation tests could be preferential in patients who still work in the same field. We believe that cooperation with the patient's occupational physician and adequate recognition of the work environment will improve the consistency of legal and medical diagnoses.

Risk factors of mesenteric venous thrombosis and current situation of diagnosis and treatment in China

International Nuclear Information System (INIS)

Zhuang Zhiwei; Zhu Huanxing; Xu Changsheng

2010-01-01

Objective: To investigate risk factors of mesenteric venous thrombosis and current situation of diagnosis and treatment in China. Methods: One hundred and seven case of mesenteric venous thrombosis reported in literature were analyzed. The literature from 2003 to 2007 were retrieved from Chinese Scientific and Technical Periodical Database and Wanfangdata. Results: One hundred and seven papers included 978 MVT patients, male: female = 1. 9:1, the average age was 47. 9. The most common risk factors were portal hypertension (28. 9% ), splenectomy (18. 8%) and thrombophlebitis (11. 5%) in 833 cases with integrated medical history. Final diagnosis was established by medical imageology (40. 0%) and exploratory laparotomy (60. 0%). The achievement ratio of thrombolysis therapy was 83. 9% (73 /87) by peripheral vein and 90. 0% (63 /70) by superior mesenteric artery. 34. 7% patients took warfarin orally after discharge. Conclusions: Portal hypertension, splenectomy and thrombophlebitis may be the most common risk factor for MVT; through peripheral vein or superior mesenteric artery urokinase thrombolytic therapy is an effective means of treatment of early MVT; MVT diagnostic awareness and anticoagulant therapy after surgery awareness of the importance is to be strengthened. (authors)

Dissemination of Continuing Education Materials Via Television Delivery Systems. Final Technical Report and Final Report.

Science.gov (United States)

Munushian, Jack

In 1972, the University of Southern California School of Engineering established a 4-channel interactive instructional television network. It was designed to allow employees of participating industries to take regular university science and engineering courses and special continuing education courses at or near their work locations. Final progress…

Pancreatic adenocarcinoma: combination of MR imaging, MR angiography and MR cholangiopancreatography for the diagnosis and assessment of resectability

International Nuclear Information System (INIS)

Catalano, C.; Pavone, P.; Laghi, A.; Panebianco, V.; Scipioni, A.; Fanelli, F.; Brillo, R.; Passariello, R.

1998-01-01

The purpose of this study was to determine the possibility of integrating MR cholangiopancreatography (MRCP) and MR angiography (MRA) to conventional MR images in the diagnosis and assessment of resectability of pancreatic adenocarcinoma. Twenty-three patients with pancreatic adenocarcinoma were prospectively examined with MR. Conventional MR images were acquired in all patients. Three-dimensional MRCP and MRA images were acquired in all patients with suspected biliary and vascular involvement. Acquisition time was less than 45 min in all cases. Images were independently evaluated by two radiologists, with final reading decided by consensus among readers. Diagnosis was confirmed with surgery in 16 patients and with percutaneous biopsy in 7. Concordance among readers was high with a kappa value of 0.83. Pancreatic adenocarcinoma was observed in all patients. Correct assessment of unresectability due to vascular involvement was found in 22 of 23 patients. Biliary obstruction was evident in 13 patients, involving the biliary and pancreatic ducts in 9 and the biliary ducts only in 4. Technical advances permit extensive use of MRI in the evaluation of abdominal pathologies. The combination of MR imaging, MRCP, and MRA can provide sufficient information for the diagnosis and assessment of resectability of pancreatic adenocarcinoma, which otherwise would require three different exams. (orig.)

Assessment of technical risks and R and D requirements for a magnetic confinement fusion fuel system. Final report

International Nuclear Information System (INIS)

DeFreece, D.A.

1983-11-01

This report documents a specific use and results of a novel technique for assessing the technical risks associated with the hardware development of a possible future commercial fusion power plant fuel system. Technical risk is defined as the risk that a particular technology or component which is currently under development will not achieve a set of required technical specifications. A technical risk assessment is the quantification of this risk. This Technical Risk Assessment (TRA) methodology was applied to a deuterium-tritium fuel system for a magnetic-confinement fusion power plant. The fuel system is defined to support a generic commercial reactor with at least two viable options for each critical subsystem. Each subsystem option is defined in detail including nominal performance requirements and subsystem interfaces. Subsystem experts were canvassed to obtain values for past, present and future technical performance parameters for each of the subsystem options. These forecasts are presented as probabilities of achieving given levels of performance in specific time periods for assumed funding scenarios. Several funding scenarios were examined to discern whether performance limitations are caused by funding or technology. A computerized Fuel System simulation is described which uses these subsystem performance parameter forecasts as inputs

Final disposal of radioactive wastes. Site selection criteria. Technical and economical factors

International Nuclear Information System (INIS)

Granero, J.J.

1984-01-01

General considerations, geological and socioeconomical criteria for final disposal of radioactive wastes in geological formations are treated. More attention is given to the final disposal of high level radioactive wastes and different solutions searched abroad which seems of interest for Spain. (author)

Santa Barbara Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hacker, Angela; Hansen, Sherman; Watkins, Ashley

2013-11-30

This report serves as the Final Report for Santa Barbara County’s Energy Efficiency and Conservation Block Grant (EECBG) BetterBuildings Neighborhood Program (BBNP) award from the U.S. Department of Energy (DOE). This report explains how DOE BBNP funding was invested to develop robust program infrastructure designed to help property owners complete energy improvements, thereby generating substantial outcomes for the local environment and economy. It provides an overview of program development and design within the grant period, program accomplishments and challenges to date, and a plan for the future sustainability of emPower, the County’s innovative clean energy and building efficiency program. During the grant period, Santa Barbara County’s emPower program primarily targeted 32,000 owner occupied, single family, detached residential homes over 25 years old within the County. In order to help these homeowners and their contractors overcome market barriers to completing residential energy improvements, the program developed and promoted six voluntary, market-based service areas: 1) low cost residential financing (loan loss reserve with two local credit unions), 2) residential rebates, 3) local customer service, 4) expert energy advising, 5) workforce development and training, and 6) marketing, education and outreach. The main goals of the program were to lower building energy use, create jobs and develop a lasting regional building performance market. These services have generated important early outcomes and lessons after the program’s first two years in service. The DOE BBNP funding was extended through October 2014 to enable Santa Barbara County to generate continued outcomes. In fact, funding related to residential financing remains wholly available for the foreseeable future to continue offering Home Upgrade Loans to approximately 1,300 homeowners. The County’s investment of DOE BBNP funding was used to build a lasting, effective, and innovative

Emergency response technical centre of the IPSN

International Nuclear Information System (INIS)

Dallendre, R.

2000-01-01

The Institute for Nuclear Safety and Protection (IPSN), the technical support of the French nuclear safety authority, provides the technical support needed for protect the surrounding population from the consequences of radioactive releases. In the event of an accident arising at a nuclear facility, the IPSN would set up an Emergency Response Technical Centre (CTC) at Fontenay-aux-Roses. The IPSN's objectives are: (a) to diagnose the state of the nuclear facility and monitor its development, (b) to prepare prognosis for the evolution of the accident and to give an estimation of the associated consequences according to the situation evolution, (c) to estimate the risk of radioactive releases and the consequences on man and on the environment, mainly on the basis of weather forecasts and on the prognosis. This diagnosis-prognosis approach is build-up with the information on the state of the installation given by: the concerned site via audio-conference system and telescope, the security panels of the nuclear plant via networks. To perform its missions, the CTC, which has to be both safe and secure, uses multiple telecommunication resources to dialogue with partners and also mapping computer systems, data bases and software tools: (a) the SESAME system, which gives, during an accident of a PWR, a calculation method for the diagnosis-prognosis aforesaid, (b) the CONRAD system, which calculates the atmospheric dispersal of radioactive substances and consequences in the environment in the early phase of an accident, (c) the ASTRAL code, which allows to cope with long lasting situations. In order to be operational, the IPSN expert regularly undergo training in emergency situation management and participate in exercises organised by the government authorities. (author)

[Technical report on the 2009 influenza A (H1N1) pandemic].

Science.gov (United States)

2010-01-01

Since its appearance in April 2009, the influenza A (H1N1) pandemic has been a subject of continued attention by national and international health authorities, as well as in the communication media. It has been six months since the first cases were published and the winter season has just ended in the southern hemisphere. Therefore, we now have quite extensive knowledge on the behaviour of the disease, its severity and the way it manifests itself in the child/adolescent population. The Spanish Paediatric Association commissioned its Evidence Based Medicine Working Group to prepare a technical report on the influenza pandemic. This report has been prepared following the highly structured working methodology proposed by the so-called Evidence Based Medicine (EBM). This methodology requires formulating clinical questions, carrying out a systematic review of the literature looking for research works that could answer them, the critical reading of these, evaluating their methodology quality and clinical importance and finally, establishing recommendations based on those studies considered valid and important as well as on good clinical judgement. The present report approaches all aspects of the influenza pandemic considered to be of interest: extent of the disease, clinical and laboratory diagnosis, physical prevention measures, vaccination and pharmacological treatment. The target population of the report are children and adolescents. Many of the considerations made may also be applied to other age groups. The primary objective of this report is to establish a group of recommendations which may serve as a generic framework for the prevention, diagnosis and treatment of the pandemic influenza in children and adolescents. The final targets of the report are paediatricians and also general/family doctors and nurses who look after children and adolescents. Copyright (c) 2009 Asociación Española de Pediatría. Published by Elsevier Espana. All rights reserved.

77 FR 42637 - Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Corrections

Science.gov (United States)

2012-07-20

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Parts 84 and 115 [Docket No. USCG-2012-0306] RIN 1625-AB86 Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments...), the Coast Guard published a final rule entitled ``Navigation and Navigable Waters; Technical...

Evaluation of effects of phenol recovery on biooxidation and tertiary treatment of SRC-I wastewater. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Mitchell, J.W.; Watt, J.C.; Cowan, W.F.; Schuyler, S.E.

1983-09-01

Addition of phenol recovery to the wastewater treatment scheme in the Baseline Design for the SRC-I Demonstration Plant was evaluated as a major post-Baseline effort. Phenol recovery affects many downstream processes, but this study was designed to assess primarily its effects on biooxidation and subsequent tertiary treatment. Two parallel treatment schemes were set up, one to treat dephenolated wastewaters and the other for processed nondephenolated wastewaters, a simulation of the Baseline Design. The study focused on comparisons of five areas: effluent quality; system stability; the need for continuous, high-dose powdered activated carbon (PAC) augmentation to the bioreactor; minimum bioreactor hydraulic residence time (HRT); and tertiary treatment requirements. The results show that phenol recovery improves the quality of the bioreactor effluent in terms of residual organics and color. With phenol recovery, PAC augmentation is not required; without phenol recovery, PAC is needed to produce a comparable effluent. Dephenolization also enhances the stability of biooxidation, and reduces the minimum HRT required. With tertiary treatment, both schemes can meet the effluent concentrations published in the SRC-I Final Envivornmental Impact Statement, as well as the anticipated effluent limits. However, phenol recovery does provide a wider safety margin and could eliminate the need for some of the tertiary treatment steps. Based solely on the technical merits observed in this study, phenol recovery is recommended. The final selection should, however, also consider economic tradeoffs and results of other studies such as toxicology testing of the effluents. 34 references, 30 figures and 26 tables.

Final Technical Report for Quantum Embedding for Correlated Electronic Structure in Large Systems and the Condensed Phase

Energy Technology Data Exchange (ETDEWEB)

Chan, Garnet Kin-Lic [Princeton Univ., NJ (United States)

2017-04-30

This is the final technical report. We briefly describe some selected results below. Developments in density matrix embedding. DMET is a quantum embedding theory that we introduced at the beginning of the last funding period, around 2012-2013. Since the first DMET papers, which demonstrated proof-of- principle calculations on the Hubbard model and hydrogen rings, we have carried out a number of different developments, including: Extending the DMET technology to compute broken symmetry phases, including magnetic phases and super- conductivity (Pub. 13); Calibrating the accuracy of DMET and its cluster size convergence against other methods, and formulation of a dynamical cluster analog (Pubs. 4, 10) (see Fig. 1); Implementing DMET for ab-initio molecular calculations, and exploring different self-consistency criteria (Pubs. 9, 14); Using embedding to defi ne quantum classical interfaces Pub. 2; Formulating DMET for spectral functions (Pub. 7) (see Fig. 1); Extending DMET to coupled fermion-boson problems (Pub. 12). Together with these embedding developments, we have also implemented a wide variety of impurity solvers within our DMET framework, including DMRG (Pub. 3), AFQMC (Pub. 10), and coupled cluster theory (CC) (Pub. 9).

Scientific-technical cooperation with foreign (esp. Europe and INSC partner countries) nuclear regulatory authorities and their technical support organizations in the fields of nuclear safety of operating nuclear power plants and on the concept evaluation of generation 3+ plants. Final report

International Nuclear Information System (INIS)

Wolff, Holger

2016-09-01

The BMUB/BfS-Project 3614I01512 forms the frame of the GRS for the scientific-technical cooperation with Technical Support Organisations and Nuclear Regulatory Authorities in the field of nuclear safety in operating NPPs and for the concept evaluation of generation 3 + plants in Europe and INSC Partner Countries. In the present final project report results are described which were gained within the project duration 15.10.2014 up to the 30.09.2016 in the following working packages: Investigations following the catastrophe of Fukushima Daiichi, Evaluation of selected National Action Plans, DBA and severe accident analyses for NPP with PWR (WWER-440, WWER-1000), cooperation with INSC partner countries on DBA, BDBA and severe accident analyses for WWER plants of generation 3 + and building NRA and safety evaluation capacities and decommissioning of nuclear facilities and disposal of radioactive waste. The results are preceded by an outline on the activities related to the project management and to the planning of the bilateral work.

Pitfalls in the MR diagnosis of primary malignant bone tumors

International Nuclear Information System (INIS)

Bader, T.R.

1998-01-01

MRI has gained an undisputed place in the evaluation of malignant bone tumors, not only for verifying results of conventional radiography and clarifying differential diagnoses; it has also become increasingly important for the assessment of the malignant/benign nature of the tumor, its growth rate, definition of adequate sites for biopsy, local preoperative staging, and evaluation of the response to chemotherapy. However, several pitfalls have to be observed regarding choice of technical parameters (coils, sequences, imaging planes), tissue differentiation, and tumor staging. When staging malignant tumors, critical aspects which have to be observed are tumor extension, integrity of the cortical bone, soft tissue components, infiltration of a joint or neurovascular bundle. The use of contrast agents provides important additional information but can also give rise to misinterpretations. Thus, all features of a tumor have to be observed in order to establish a final diagnosis. Particular difficulties can occur with the interpretation of MR images of osteomyelitis, osteoid osteoma, stress and insufficiency fractures, bone infarcts, myositis ossificans, hemangiomas, and aneurysmal bone cysts. (orig.) [de

TCR as supervisor of technical systems

CERN Document Server

Laeger, H

1998-01-01

Our Technical Control Room (TCR) provides continuous supervision of CERN's technical infrastructure. It also serves the inhabitants of CERN's premises as a contact point in case of problems. Every year we initiate eleven thousand recorded corrective interventions; about half subsequent to user phone calls, the other half to automatic alarms. TCR tasks are essentially fourfold: collect and distribute information on abnormal operation states; supervise those technical systems for which we have a mandate; initiate corrective interventions; and perform corrective on-site interventions outside normal working hours. A TCR operator normally has an education corresponding to a French BTS and initially little professional experience. He holds short-term contracts, up to a maximum of six years. This paper outlines TCR tasks and presents some statistical data. It also indicates relations between users, equipment groups, contract firms and the TCR as go-between. Finally, it gives an account of our seven years experience ...

Modular Electric Vehicle Program (MEVP). Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The Modular Electric Vehicle Program (MEVP) was an EV propulsion system development program in which the technical effort was contracted by DOE to Ford Motor Company. The General Electric Company was a major subcontractor to Ford for the development of the electric subsystem. Sundstrand Power Systems was also a subcontractor to Ford, providing a modified gas turbine engine APU for emissions and performance testing as well as a preliminary design and producibility study for a Gas Turbine-APU for potential use in hybrid/electric vehicles. The four-year research and development effort was cost-shared between Ford, General Electric, Sundstrand Power Systems and DOE. The contract was awarded in response to Ford`s unsolicited proposal. The program objective was to bring electric vehicle propulsion system technology closer to commercialization by developing subsystem components which can be produced from a common design and accommodate a wide range of vehicles; i.e., modularize the components. This concept would enable industry to introduce electric vehicles into the marketplace sooner than would be accomplished via traditional designs in that the economies of mass production could be realized across a spectrum of product offerings. This would eliminate the need to dedicate the design and capital investment to a limited volume product offering which would increase consumer cost and/or lengthen the time required to realize a return on the investment.

Technical bid evaluation

International Nuclear Information System (INIS)

Bruchhausen, E. v.

1975-01-01

It is shown which kind of problems arise for the owners of the project and what is the recommendable method of approach. A detailed description of the necessary working team, information in delegation of work and tasks of procedure, criteria of valuation and classification method. Examples of schemes are shown which are the basis of the technical bid evaluation: tables 'data of system/component' and 'scope of supply'. The procedure of normalization of the bids and of specifying the owners supplies are explained. The content of the final report is described. (HP) [de

Job and task analysis for technical staff

International Nuclear Information System (INIS)

Toline, B.C.

1991-01-01

In September of 1989 Cooper Nuclear Station began a project to upgrade the Technical Staff Training Program. This project's roots began by performing job and Task Analysis for Technical Staff. While the industry has long been committed to Job and Task Analysis to target performance based instruction for single job positions, this approach was unique in that it was not originally considered appropriate for a group as diverse as Tech Staff. Much to his satisfaction the Job and Task Analysis Project was much less complicated for Technical Staff than the author had imagined. The benefits of performing the Job and Task Analysis for Technical Staff have become increasingly obvious as he pursues lesson plan development and course revisions. The outline for this presentation will be as follows: philosophy adopted; preparation of the job survey document; performing the job analysis; performing task analysis for technical staff and associated pitfalls; clustering objectives for training and comparison to existing program; benefits now and in the future; final phase (comparison to INPO guides and meeting the needs of non-degreed engineering professionals); and conclusion. By focusing on performance based needs for engineers rather than traditional academics for training the author is confident the future Technical Staff Program will meet the challenges ahead and will exceed requirements for accreditation

Final Technical Report for DE-SC0012297

Energy Technology Data Exchange (ETDEWEB)

Dell' Antonio, Ian [Brown Univ., Providence, RI (United States)

2017-08-01

This is the final report on the work performed in award DE-SC0012297, Cosmic Frontier work in support of the LSST Dark Energy Science Collaboration's work to develop algorithms, simulations, and statistical tests to ensure optimal extraction of the dark energy properties from galaxy clusters observed with LSST. This work focused on effects that could produce a systematic error on the measurement of cluster masses (that will be used to probe the effects of dark energy on the growth of structure). These effects stem from the deviations from pure ellipticity of the gravitational lensing signal and from the blending of light of neighboring galaxies. Both these effects are expected to be more significant for LSST than for the stage III experiments such as the Dark Energy Survey. We calculate the magnitude of the mass error (or bias) for the first time and demonstrate that it can be treated as a multiplicative correction and calibrated out, allowing mass measurements of clusters from gravitational lensing to meet the requirements of LSST's dark energy investigation.

Fault Diagnosis in Dynamic Systems Using Fuzzy Interacting Observers

Directory of Open Access Journals (Sweden)

N. V. Kolesov

2013-01-01

Full Text Available A method of fault diagnosis in dynamic systems based on a fuzzy approach is proposed. The new method possesses two basic specific features which distinguish it from the other known fuzzy methods based on the application of fuzzy logic and a bank of state observers. First, this method uses a bank of interacting observers instead of traditional independent observers. The second specific feature of the proposed method is the assumption that there is no strict boundary between the serviceable and disabled technical states of the system, which makes it possible to specify a decision making rule for fault diagnosis.

CEEM Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bowers, John [Univ. of California, Santa Barbara, CA (United States)

2014-11-26

concentrating photovoltaic applications thathave substantially higher efficiency than single substrate cells made of elemental semiconductors such as silicon. This task required the development of new cell bonding methods with excellent coupling of both photons and electrons between the sub-cells. To accomplish this, we developed (1) GaInN solar cells with enhanced performance by using quantum-well absorbers and front-surface optical texturing, (2) a hybrid "pillar-array" bond which uses an array of metal pillars for electrical coupling, and (3) a "hybrid moth-eye" optical coating which combines the benefits of nano-imprinted moth-eye coatings and traditional multilayer coatings. The technical effectiveness was assessed by measurement of the photovoltaic efficiency of solar cells made using these techniques; the ultrahigh efficiencies targeted by this work are of compelling economic value for concentrating photovoltaics.

Measurable Control System Security through Ideal Driven Technical Metrics

Energy Technology Data Exchange (ETDEWEB)

Miles McQueen; Wayne Boyer; Sean McBride; Marie Farrar; Zachary Tudor

2008-01-01

The Department of Homeland Security National Cyber Security Division supported development of a small set of security ideals as a framework to establish measurable control systems security. Based on these ideals, a draft set of proposed technical metrics was developed to allow control systems owner-operators to track improvements or degradations in their individual control systems security posture. The technical metrics development effort included review and evaluation of over thirty metrics-related documents. On the bases of complexity, ambiguity, or misleading and distorting effects the metrics identified during the reviews were determined to be weaker than necessary to aid defense against the myriad threats posed by cyber-terrorism to human safety, as well as to economic prosperity. Using the results of our metrics review and the set of security ideals as a starting point for metrics development, we identified thirteen potential technical metrics - with at least one metric supporting each ideal. Two case study applications of the ideals and thirteen metrics to control systems were then performed to establish potential difficulties in applying both the ideals and the metrics. The case studies resulted in no changes to the ideals, and only a few deletions and refinements to the thirteen potential metrics. This led to a final proposed set of ten core technical metrics. To further validate the security ideals, the modifications made to the original thirteen potential metrics, and the final proposed set of ten core metrics, seven separate control systems security assessments performed over the past three years were reviewed for findings and recommended mitigations. These findings and mitigations were then mapped to the security ideals and metrics to assess gaps in their coverage. The mappings indicated that there are no gaps in the security ideals and that the ten core technical metrics provide significant coverage of standard security issues with 87% coverage. Based

Ion beam diagnosis

International Nuclear Information System (INIS)

Strehl, P.

1994-04-01

This report is an introduction to ion beam diagnosis. After a short description of the most important ion beam parameters measurements of the beam current by means of Faraday cups, calorimetry, and beam current transformers and measurements of the beam profile by means of viewing screens, profile grids and scanning devices, and residual gas ionization monitors are described. Finally measurements in the transverse and longitudinal phase space are considered. (HSI)

Economic Reform Orchestra And Technical Manpower Development ...

African Journals Online (AJOL)

The study examined economic reform issues in Nigeria since 1986 and the impact on technical manpower development in Rivers State in particular. Two sets of structured questionnaire were used to elicit responses from target respondents who ultimately comprised 105 instructors and 340 final year students in the four ...

Preconception carrier screening and prenatal diagnosis in thalassemia and hemoglobinopathies: challenges and future perspectives.

Science.gov (United States)

Traeger-Synodinos, Joanne; Harteveld, Cornelis L

2017-03-01

Hemoglobinopathies constitute the most common severe monogenic disorders worldwide, with an increasing global burden each year. The benefit of applying programmes for preconception carrier screening, with the option of prenatal diagnosis, to minimize the incidence of new cases is recognized in many countries. Areas covered: The challenges associated with identifying carrier couples using hematology-based screening, along with DNA diagnosis and prenatal diagnosis were addressed, based on a literature search and the authors expertise. Expert commentary: The hemoglobinopathies are extremely heterogeneous at the haematological, molecular and clinical level, requiring appropriately equipped and staffed laboratories with experience to support comprehensive screening and diagnosis. However complete services with adequate infrastructure to address the associated technical challenges do not exist widely, especially in low-income countries that, coincidentally, are often those with the highest frequency of hemoglobinopathies in their population. Additionally, overcoming limited public awareness, education and absence of systematic dissemination of information also constitutes a challenge. This article aims to highlight these challenges and to evaluate potential future developments that may address at least some of them, focusing mainly on the technical challenges related to molecular diagnostics.

[Review comments on the Draft DOE Area Recommendation Report for the Crystalline Repository Project]: Final technical report

International Nuclear Information System (INIS)

Dutch, S.I.; Stiegliltz, R.D.

1986-03-01

Research performed under the grant primarily involved review and comment on the Draft Area Recommendations Report (DARR). However, because data and ''recommendations'' included in the DARR are unquestionably tied to years of research and dozens of technical reports and documents, i.e., Screening Methodologies, Regional characterization Reports, etc., it is essential that consultants to the Menominee Tribe review all the relevant DOE documents, working papers, etc. Given the short period provided for technical comment and limited funds available to the Tribe, a well designed and thorough technical review was (and is) without question impossible. What review and comment that did occur on a geotechnical level is included in this report

Improved Barriers to Turbine Engine Fragments: Final Annual Report

National Research Council Canada - National Science Library

Shockey, Donald

2002-01-01

This final annual technical report describes the progress rnade during year 4 of the SPI International Phase II effort to develop a computational capability for designing lightweight fragment barriers...

failures diagnosis. Theory and practice for industrial systems

International Nuclear Information System (INIS)

Zwingelstein, G.

1995-01-01

Failure diagnosis methods represent appreciable tools for the maintenance and the improvement of availability and safety in complex industrial installations. The industrial diagnosis can be assimilated to a deterministic causality relation between the cause and the effect. This book describes the methodology associated to the resolution of the diagnosis problem applied to complex industrial system failures, and evaluates the principles of the main diagnosis methods. The introduction presents the terminology and norms used in the industry to situate the diagnosis context in the possession cost of a product. After a formulation of the diagnosis in the form of the resolution of inverse problems, the author gives details about the inductive and deductive methods and about internal and external diagnosis methods. Each method is illustrated with examples taken in the industry with recommendations about their operating limitations. Finally, a guideline summarizes the principal criteria for the selection of an industrial diagnosis method according to the available informations. (J.S.). 168 refs., 294 figs., 22 tabs., 1 annexe

How to be an Effective Technical Writer?

Directory of Open Access Journals (Sweden)

M Solaiman Ali

2012-07-01

(patterns of organization of information to suit the technical writing task, checking for technical accuracy and following three levels of editing to help increase the readability of a technical text. Finally, in part 8 (Ethical/legal considerations for the technical writer, the authors suggest ways for the technical writer to overcome ethical/legal dilemmas on the job.

Technical Report Cellulosic Based Black Liquor Gasification and Fuels Plant Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Fornetti, Micheal [Escanaba Paper Company, MI (United States); Freeman, Douglas [Escanaba Paper Company, MI (United States)

2012-10-31

The Cellulosic Based Black Liquor Gasification and Fuels Plant Project was developed to construct a black liquor to Methanol biorefinery in Escanaba, Michigan. The biorefinery was to be co-located at the existing pulp and paper mill, NewPage’s Escanaba Paper Mill and when in full operation would: • Generate renewable energy for Escanaba Paper Mill • Produce Methanol for transportation fuel of further refinement to Dimethyl Ether • Convert black liquor to white liquor for pulping. Black liquor is a byproduct of the pulping process and as such is generated from abundant and renewable lignocellulosic biomass. The biorefinery would serve to validate the thermochemical pathway and economic models for black liquor gasification. It was a project goal to create a compelling new business model for the pulp and paper industry, and support the nation’s goal for increasing renewable fuels production and reducing its dependence on foreign oil. NewPage Corporation planned to replicate this facility at other NewPage Corporation mills after this first demonstration scale plant was operational and had proven technical and economic feasibility. An overview of the process begins with black liquor being generated in a traditional Kraft pulping process. The black liquor would then be gasified to produce synthesis gas, sodium carbonate and hydrogen sulfide. The synthesis gas is then cleaned with hydrogen sulfide and carbon dioxide removed, and fed into a Methanol reactor where the liquid product is made. The hydrogen sulfide is converted into polysulfide for use in the Kraft pulping process. Polysulfide is a known additive to the Kraft process that increases pulp yield. The sodium carbonate salts are converted to caustic soda in a traditional recausticizing process. The caustic soda is then part of the white liquor that is used in the Kraft pulping process. Cellulosic Based Black Liquor Gasification and Fuels Plant project set out to prove that black liquor gasification could

[The heuristics of reaching a diagnosis].

Science.gov (United States)

Wainstein, Eduardo

2009-12-01

Making a diagnosis in medicine is a complex process in which many cognitive and psychological issues are involved. After the first encounter with the patient, an unconscious process ensues to suspect the presence of a particular disease. Usually, complementary tests are requested to confirm the clinical suspicion. The interpretation of requested tests can be biased by the clinical diagnosis that was considered in the first encounter with the patient. The awareness of these sources of error is essential in the interpretation of the findings that will eventually lead to a final diagnosis. This article discusses some aspects of the heuristics involved in the adjudication of priory probabilities and provides a brief review of current concepts of the reasoning process.

Organisation, Quality and Challenges in the B. Ed Technical ...

African Journals Online (AJOL)

Technical) degree programme rated the organization and quality of the industrial attachment component of the programme. Challenges students faced during industrial attachment were also examined. A case study design was used. Twenty-five final ...

The Preimplantation Genetic Diagnosis: Legal Aspects in the Spanish Law

Directory of Open Access Journals (Sweden)

Marina Moya González

2018-03-01

Full Text Available This paper analyses the preimplantation genetic diagnosis (PGD in Spain, and the legal aspects. It exposes the technical characteristics, as well as the ethical and social consequences. It compares the different rules of law about assisted human reproduction techniques in Spain, and those in some European countries.

Program of technical assistance to the Organization for the Prohibition of Chemical Weapons - lessons learned from the U.S. program of technical assistance to IAEA safeguards. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The Defense Nuclear Agency is sponsoring a technical study of the requirements of a vehicle to meet the OPCW`s future needs for enhanced chemical weapons verification capabilities. This report provides information about the proven mechanisms by which the U.S. provided both short- and long-term assistance to the IAEA to enhance its verification capabilities. Much of the technical assistance has generic application to international organizations verifying compliance with disarmament treaties or conventions. In addition, some of the equipment developed by the U.S. under the existing arrangements can be applied in the verification of other disarmament treaties or conventions. U.S. technical assistance to IAEA safeguards outside of the IAEA`s regular budget proved to be necessary. The U.S. technical assistance was successful in improving the effectiveness of IAEA safeguards for its most urgent responsibilities and in providing the technical elements for increased IAEA {open_quotes}readiness{close_quotes} for the postponed responsibilities deemed important for U.S. policy objectives. Much of the technical assistance was directed to generic subjects and helped to achieve a system of international verification. It is expected that the capabilities of the Organization for the Prohibition of Chemical Weapons (OPCW) to verify a state`s compliance with the {open_quotes}Chemical Weapons Convention{close_quotes} will require improvements. This report presents 18 important lessons learned from the experience of the IAEA and the U.S. Program of Technical Assistance to IAEA Safeguards (POTAS), organized into three tiers. Each lesson is presented in the report in the context of the difficulty, need and history in which the lesson was learned. Only the most important points are recapitulated in this executive summary.

Technical activities, 1990: Surface Science Division

International Nuclear Information System (INIS)

Powell, C.J.

1991-05-01

The report summarizes technical activities and accomplishments of the NIST Surface Science Division during Fiscal Year 1990. Overviews are presented of the Division and of its three constituent groups: Surface Dynamical Processes, Thin Films and Interfaces, and Surface Spectroscopies and Standards. These overviews are followed by reports of selected technical accomplishments during the year. A summary is given of Division outputs and interactions that includes lists of publications, talks, committee assignments, seminars (including both Division seminars and Interface Science seminars arranged through the Division), conferences organized, and a standard reference material certified. Finally, lists are given of Division staff and of guest scientists who have worked in the Division during the past year

Usefulness of CT in the diagnosis and management of acute abdomen

International Nuclear Information System (INIS)

Suzuki, Takuya; Matsumoto, Junichi; Funakubo, Masakatsu; Yamashita, Hirotaka; Ehara, Norishige; Minowa, Yoshiyuki; Nakajima, Yasuo

2010-01-01

We prospectively evaluated the usefulness of computed tomography (CT) in the diagnosis and management of acute abdomen. Ninety-four patients with acute abdomen were enrolled. We compared the final diagnosis and management CT diagnosis and management. Then, we evaluated how many of the CT examinations were useful and the degree to which they were useful. In more than 90% of cases, CT was very useful for the diagnosis and management of acute abdomen. (author)

Technical approach document

International Nuclear Information System (INIS)

1989-12-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

Texas Hydrogen Education Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hitchcock, David; Bullock, Dan

2011-06-30

, and hydrogen fueling) are effective for engaging target audiences, and (3) a clear path forward is needed for state and local agencies interested in project implementation (funding, financing, preliminary design, technical assistance, etc.).

Five misconceptions in cancer diagnosis

Science.gov (United States)

Hamilton, William

2009-01-01

Much investment has been put into facilities for early cancer diagnosis. It is difficult to know how successful this investment has been. New facilities for rapid investigation in the UK have not reduced mortality, and may cause delays in diagnosis of patients with low-risk, or atypical, symptoms. In part, the failure of new facilities to translate into mortality benefits can be explained by five misconceptions. These are described, along with suggested research and organisational remedies. The first misconception is that cancer is diagnosed in hospitals. Consequently, secondary care data have been used to drive primary care decisions. Second, GPs are thought to be poor at cancer diagnosis, yet the type of education on offer to improve this may not be what is needed. Third, symptomatic cancer diagnosis has been downgraded in importance with the introduction of screening, yet screening identifies only a small minority of cancers. Fourth, pressure is put on GPs to make referrals for those with an individual high risk of cancer — disenfranchising those with ‘low-risk but not no-risk’ symptoms. Finally, considerable nihilism exists about the value of early diagnosis, despite considerable observational evidence that earlier diagnosis of symptomatic cancer is beneficial. PMID:19520027

Radiological Effluent Technical Specifications (RETS) implementation, Kewaunee Nuclear Power Plant

International Nuclear Information System (INIS)

Serrano, W.; Akers, D.W.

1985-06-01

A review of the Radiological Effluent Technical Specifications (RETS) for the Kewaunee Nuclear Power Plant was performed. The principal review guidelines used were NUREG-0133, ''Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants,'' and Draft 7'' of NUREG-0472, Revision 3, ''Radiological Effluent Technical Specifications for Pressurized Water Reactors.'' Draft submittals were discussed with the Licensee by the NRC staff until all items requiring changes to the Technical Specifications were resolved. The Licensee then submitted final proposed RETS to the NRC which were evaluated and found to be in compliance with the NRC review guidelines. The proposed Offsite Dose Calculation Manual and the Radiological Environmental Monitoring Manual were reviewed and generally found to be in compliance with the NRC review guidelines

SIAM Conference on Geometric Design and Computing. Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

None

2002-03-11

The SIAM Conference on Geometric Design and Computing attracted 164 domestic and international researchers, from academia, industry, and government. It provided a stimulating forum in which to learn about the latest developments, to discuss exciting new research directions, and to forge stronger ties between theory and applications. Final Report

[Critical thinking skills in the nursing diagnosis process].

Science.gov (United States)

Bittencourt, Greicy Kelly Gouveia Dias; Crossetti, Maria da Graça Oliveira

2013-04-01

The aim of this study was to identify the critical thinking skills utilized in the nursing diagnosis process. This was an exploratory descriptive study conducted with seven nursing students on the application of a clinical case to identify critical thinking skills, as well as their justifications in the nursing diagnosis process. Content analysis was performed to evaluate descriptive data. Six participants reported that analysis, scientific and technical knowledge and logical reasoning skills are important in identifying priority nursing diagnoses; clinical experience was cited by five participants, knowledge about the patient and application of standards were mentioned by three participants; Furthermore, discernment and contextual perspective were skills noted by two participants. Based on these results, the use of critical thinking skills related to the steps of the nursing diagnosis process was observed. Therefore, that the application of this process may constitute a strategy that enables the development of critical thinking skills.

Accuracy of routine cytology and immunocytochemistry in preoperative diagnosis of oral amelanotic melanomas in dogs.

Science.gov (United States)

Przeździecki, Rafał; Czopowicz, Michał; Sapierzyński, Rafał

2015-12-01

Amelanotic melanomas are one of the most common oral malignancies. The cytologic and histopathologic differentiation between amelanotic melanoma, sarcoma, and poorly differentiated carcinoma is often difficult or even impossible. The aim of this study was to assess the reliability of routine cytology and immunocytochemistry in preoperative diagnosis of canine oral amelanotic melanoma. Cytologic preparations from undifferentiated canine oral tumors were stained with Giemsa and by immunocytochemistry (ICC) using anti-cytokeratin, anti-vimentin, and anti-Melan A antibodies. The final cytologic diagnosis (including ICC) was compared to the final diagnosis based on histopathology and immunohistochemistry (IHC) results, and sensitivity and specificity of cytologic examination were determined. Final cytologic diagnoses of 38 cases agreed well with the histopathologic/immunohistochemical diagnoses, thus both specificity and sensitivity of combined routine cytology and ICC were 100% (95% confidence interval 90.8-100%). Of 32 oral tumors, diagnosis of amelanotic melanoma, sarcoma, and carcinoma was made using routine cytology and ICC. In 4 of 6 aspirates taken from lymph nodes, a preliminary diagnosis of metastatic amelanotic melanoma corresponded with the final diagnosis. Both sensitivity and specificity of routine cytology in diagnosis of amelanotic melanomas were considered moderate (66.7% and 85.7%, respectively). In conclusion, routine cytology is a reliable diagnostic method for canine oral amelanotic melanoma and metastatic amelanotic melanoma, and ICC, using anti-cytokeratin, anti-vimentin, and anti-Melan A antibodies, is an excellent supporting method for presurgical diagnosis of poorly differentiated oral malignancies in dogs. © 2015 American Society for Veterinary Clinical Pathology.

77 FR 8095 - Technical Corrections to Commission Regulations

Science.gov (United States)

2012-02-14

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission 18 CFR Part 2 [Docket No. RM11-30-000; Order No. 756] Technical Corrections to Commission Regulations Issued February 8, 2012. AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Final rule: correcting amendment. SUMMARY: This document adds...

76 FR 16235 - Corporate Credit Unions, Technical Corrections

Science.gov (United States)

2011-03-23

... inadvertently included particular investments that did not--when subject to the other credit risk and asset... NATIONAL CREDIT UNION ADMINISTRATION 12 CFR Part 707 RIN 3133-AD58 Corporate Credit Unions, Technical Corrections AGENCY: National Credit Union Administration (NCUA). ACTION: Final rule. SUMMARY: In...

Laboratory Diagnosis of Chlamydia Pneumoniae Infections

Directory of Open Access Journals (Sweden)

Rosanna W Peeling

1995-01-01

Full Text Available Chlamydia pneumoniae is an important cause of respiratory illness. There is a need for accurate and rapid laboratory diagnostic methods that will lead to improved patient care, appropriate use of antimicrobial therapy and a better understanding of the epidemiology of this emerging pathogen. Culture is highly specific but is technically demanding, expensive, has a long turnaround time and its sensitivity is highly dependent on transport conditions. Antigen detection tests such as enzyme immunoassay and direct fluorescent antibody assay, and molecular detection methods such as the polymerase chain reaction assay, may provide a rapid diagnosis without the requirement for stringent transport conditions. The results of these tests should be interpreted with caution until more thorough evaluation is available. Serology remains the method of choice. The limitations of different serological methods for the laboratory diagnosis of C pneumoniae are discussed.

Diagnosis and epidemiology of animal diseases in Latin America

International Nuclear Information System (INIS)

Cooling, A.

1998-01-01

Support for scientists and their endeavours in developing countries by the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture is provided through FAO/IAEA Co-ordinated Research Projects (CRP) and IAEA Technical Co-operation Projects (TCPs). Using these mechanisms the Animal Production and Health Section of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agricultural aims to encourage and improve the capacity of national institutions in developing countries to identify and resolve problems connected with improving livestock productivity and health. In 1986, the Section introduced and animal health component into its Project. The initial support was for five years but in 1991 this was extended for a further three years and linked with the support available from the IAEA's Technical Co-operation Project through national and regional TCPs and ARCAL activities in Latin America dealing with diagnosis of animal diseases. Central to this overall project ws the use of ELISA for the diagnosis and control of livestock diseases. FAO/IAEA CRPs are developed around a well defined research topic on which between 15 and 20 national institutes collaborate - the topic itself being defined through consultation with national authorities in developing and developed countries and international agricultural research centers and organizations. The primary role of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture in such programmes is to ensure that the inputs and efforts under these programmes are co-ordinated and that the results are published. The studies being reported in this IAEA TECDOC were initiated in 1991 and whilst the focus was on three major disease affecting livestock in the region (foot-and-mouth disease (FMD), brucellosis and babesiosis) the approach taken by individual Research Control holders was different and thus in some cases research concentrated on assay validation whilst in other cases the focus was on the

A dynamic integrated fault diagnosis method for power transformers.

Science.gov (United States)

Gao, Wensheng; Bai, Cuifen; Liu, Tong

2015-01-01

In order to diagnose transformer fault efficiently and accurately, a dynamic integrated fault diagnosis method based on Bayesian network is proposed in this paper. First, an integrated fault diagnosis model is established based on the causal relationship among abnormal working conditions, failure modes, and failure symptoms of transformers, aimed at obtaining the most possible failure mode. And then considering the evidence input into the diagnosis model is gradually acquired and the fault diagnosis process in reality is multistep, a dynamic fault diagnosis mechanism is proposed based on the integrated fault diagnosis model. Different from the existing one-step diagnosis mechanism, it includes a multistep evidence-selection process, which gives the most effective diagnostic test to be performed in next step. Therefore, it can reduce unnecessary diagnostic tests and improve the accuracy and efficiency of diagnosis. Finally, the dynamic integrated fault diagnosis method is applied to actual cases, and the validity of this method is verified.

A Dynamic Integrated Fault Diagnosis Method for Power Transformers

Science.gov (United States)

Gao, Wensheng; Liu, Tong

2015-01-01

In order to diagnose transformer fault efficiently and accurately, a dynamic integrated fault diagnosis method based on Bayesian network is proposed in this paper. First, an integrated fault diagnosis model is established based on the causal relationship among abnormal working conditions, failure modes, and failure symptoms of transformers, aimed at obtaining the most possible failure mode. And then considering the evidence input into the diagnosis model is gradually acquired and the fault diagnosis process in reality is multistep, a dynamic fault diagnosis mechanism is proposed based on the integrated fault diagnosis model. Different from the existing one-step diagnosis mechanism, it includes a multistep evidence-selection process, which gives the most effective diagnostic test to be performed in next step. Therefore, it can reduce unnecessary diagnostic tests and improve the accuracy and efficiency of diagnosis. Finally, the dynamic integrated fault diagnosis method is applied to actual cases, and the validity of this method is verified. PMID:25685841

Biotrans functional and technical description. Report of VIEWLS WP5, modelling studies

International Nuclear Information System (INIS)

Van Tilburg, X.; Egging, R.; Londo, H.M.

2006-01-01

The overall objectives of this project are to provide structured and clear data on the availability and performance of biofuels and to identify the possibilities and strategies towards large scale sustainable production, use and trading of biofuels for the transport sector in Europe, including Central and Eastern European Countries (CEEC). The report supplements the two other reports in the work package: 'Biofuel and Bio-energy implementation scenarios - final report of VIEWLS WP5' (2005) and 'VIEWLS modelling and analysis, technical data for biofuel production chains' (2005). This document contains a functional and technical description of the BioTrans model, accompanied by a description of the system. Section 2 contains a conceptual and functional description of the biofuel model. Section 3 describes the optimisation method in technical terms, discussing aspects like the target function and constraints used. Finally, section 4 discusses the input and output requirements for the BioTrans system

SUSTAINING OCCUPATIONAL INFORMATION FOR CAREER CHOICE AND DEVELOPMENT IN STUDENTS OF TECHNICAL COLLEGES IN ENUGU STATE, NIGERIA

OpenAIRE

Moses Ikebe Odo

2015-01-01

This study takes on the issue of sustaining occupational information for career choice and development in students of technical colleges in Enugu State, Nigeria. The method adopted for this study was the survey design and the population included were all final year students of the three government technical colleges in Enugu State of Nigeria. The technical colleges were sampled as follows: Government Technical College, Enugu (156 students); Government Technical College, Nsukka (148 students);...

Tank Farms Technical Safety Requirements. Volume 1 and 2

International Nuclear Information System (INIS)

CASH, R.J.

2000-01-01

The Technical Safety Requirements (TSRs) define the acceptable conditions, safe boundaries, basis thereof, and controls to ensure safe operation during authorized activities, for facilities within the scope of the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR)

Tank Farms Technical Safety Requirements [VOL 1 and 2

Energy Technology Data Exchange (ETDEWEB)

CASH, R.J.

2000-12-28

The Technical Safety Requirements (TSRs) define the acceptable conditions, safe boundaries, basis thereof, and controls to ensure safe operation during authorized activities, for facilities within the scope of the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR).

Evolving techniques of diagnosis. Toward establishment of new paradigm for human machine cooperation

International Nuclear Information System (INIS)

Kitamura, Masaharu; Takahashi, Makoto; Kanamoto, Shigeru; Saeki, Akira; Washio, Takashi; Ohga, Yukiharu; Furuta, Kazuo; Yoshikawa, Shinji

1998-01-01

By monitoring equipments of a plant and state of a process, the diagnostic technique to detect a sign of abnormality properly to identify its reason has often been advanced on a lot of researches in various industrial fields containing atomic force. Some fundamental studies expected for such diagnostic technique to play an important role to keep and improve operational safety of a nuclear plant have been conducted since early period of the nuclear reaction development, but their contents are evolved and changed rapidly, in recent. The technique on the diagnosis was related closely to a statistical analysis method on signal fluctuation component, so-called reactor noise analysis method in early 1980s, but technical innovation step of their recent advancement were remarkable by introduction of new techniques such as chaos theory, wavelet analysis, model base application of expert system, artificial intelligence, and so on at middle of 1980s. And, when diagnosing in the field of atomic force, owing to be required for much high ability, studies on a multi method integration system considered complementary application of a plurality of technical methods and a cooperative method between human and mechanical intelligences, are also forwarded actively faster than those in other industrial areas. In this paper, in each important item, its technical nature and present state of its application to diagnosis are described with their future technical view. (G.K.)

7 CFR 1944.419 - Final grantee evaluation.

Science.gov (United States)

2010-01-01

...) PROGRAM REGULATIONS (CONTINUED) HOUSING Self-Help Technical Assistance Grants § 1944.419 Final grantee...HA or its successor agency under Public Law 103-354 employees or an organization under contract to Fm... determine how successful the grantee was in meeting goals and objectives as defined in the agreement...

78 FR 41304 - Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Correction

Science.gov (United States)

2013-07-10

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 105 [Docket No. USCG-2013-0397] RIN 1625-AC06 Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Correction AGENCY: Coast Guard, DHS. ACTION: Final rule; correction. SUMMARY: The Coast Guard published a final rule...

Development of Molten-Salt Heat Transfer Fluid Technology for Parabolic Trough Solar Power Plants - Public Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Grogan, Dylan C. P.

2013-08-15

Executive Summary This Final Report for the "Development of Molten-Salt Heat Transfer Fluid (HTF) Technology for Parabolic Trough Solar Power Plants” describes the overall project accomplishments, results and conclusions. Phase 1 analyzed the feasibility, cost and performance of a parabolic trough solar power plant with a molten salt heat transfer fluid (HTF); researched and/or developed feasible component options, detailed cost estimates and workable operating procedures; and developed hourly performance models. As a result, a molten salt plant with 6 hours of storage was shown to reduce Thermal Energy Storage (TES) cost by 43.2%, solar field cost by 14.8%, and levelized cost of energy (LCOE) by 9.8% - 14.5% relative to a similar state-of-the-art baseline plant. The LCOE savings range met the project’s Go/No Go criteria of 10% LCOE reduction. Another primary focus of Phase 1 and 2 was risk mitigation. The large risk areas associated with a molten salt parabolic trough plant were addressed in both Phases, such as; HTF freeze prevention and recovery, collector components and piping connections, and complex component interactions. Phase 2 analyzed in more detail the technical and economic feasibility of a 140 MWe,gross molten-salt CSP plant with 6 hours of TES. Phase 2 accomplishments included developing technical solutions to the above mentioned risk areas, such as freeze protection/recovery, corrosion effects of applicable molten salts, collector design improvements for molten salt, and developing plant operating strategies for maximized plant performance and freeze risk mitigation. Phase 2 accomplishments also included developing and thoroughly analyzing a molten salt, Parabolic Trough power plant performance model, in order to achieve the project cost and performance targets. The plant performance model and an extensive basic Engineering, Procurement, and Construction (EPC) quote were used to calculate a real levelized cost of energy (LCOE) of 11.50�

Development of a Foam OTEC System. Final technical report for Fiscal Year 1979

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Research on Development of a Foam OTEC System, as carried out at Carnegie-Mellon University from October 1, 1978 through September 30, 1979, is described. To a brief section summarizing highlights of research results are appended 12 technical reports which detail specific sections of the program. The work described is continuing and a proposal is currently being submitted to provide support in fiscal 1980.

Final Technical Report. DeepCwind Consortium Research Program. January 15, 2010 - March 31, 2013

Energy Technology Data Exchange (ETDEWEB)

Dagher, Habib [Univ. of Maine, Orono, ME (United States); Viselli, Anthony [Univ. of Maine, Orono, ME (United States); Goupee, Andrew [Univ. of Maine, Orono, ME (United States); Thaler, Jeffrey [Univ. of Maine, Orono, ME (United States); Brady, Damian [Univ. of Maine, Orono, ME (United States); Browne, Peter [HDR, Inc., Omaha, NE (United States); Browning, James [Univ. of Colorado, Boulder, CO (United States); Chung, Jade [Univ. of Maine, Orono, ME (United States); Coulling, Alexander [Univ. of Maine, Orono, ME (United States); Deese, Heather [Island Institute, Rockland, ME (United States); Fowler, Matthew [Univ. of Maine, Orono, ME (United States); Holberton, Rebecca [Univ. of Maine, Orono, ME (United States); Anant, Jain [Intertek, Duluth, GA (United States); Jalbert, Dustin [Univ. of Maine, Orono, ME (United States); Johnson, Theresa [Univ. of Maine, Orono, ME (United States); Jonkman, Jason [National Renewable Energy Laboratory, Golden, CO (United States); Karlson, Benjamin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kimball, Richard [Maine Maritime Academy, Castine, ME (United States); Koo, Bonjun [Technip, Paris (France); Lackner, Matthew [Univ. of Massachusetts, Amherst, MA (United States); Lambrakos, Kostas [Technip, Paris (France); Lankowski, Matthew [Univ. of Maine, Orono, ME (United States); Leopold, Adrienne [Univ. of Maine, Orono, ME (United States); Lim, Ho-Joon [Technip, Paris (France); Mangum, Linda [Univ. of Maine, Orono, ME (United States); Martin, Heather [Univ. of Maine, Orono, ME (United States); Masciola, Marco [National Renewable Energy Laboratory, Golden, CO (United States); Maynard, Melissa [Univ. of Maine, Orono, ME (United States); McCleave, James [Univ. of Maine, Orono, ME (United States); Mizrahi, Robert [New Jersey Audubon Society, Bernardsville, NJ (United States); Molta, Paul [National Renewable Energy Laboratory, Golden, CO (United States); Pershing, Andrew [Gulf of Maine Research Institute, Portland, ME (United States); Pettigrew, Neal [Univ. of Maine, Orono, ME (United States); Prowell, Ian [MMI Engineering, Oakland, CA (United States); Qua, Andrew [Kleinschmidt Associates, Pittsfield, ME (United States); Sherwood, Graham [Gulf of Maine Research Institute, Portland, ME (United States); Snape, Thomas [Univ. of Maine, Orono, ME (United States); Steneck, Robert [Univ. of Maine, Orono, ME (United States); Stewart, Gordon [Univ. of Massachusetts, Amherst, MA (United States); Stockwell, Jason [Gulf of Maine Research Institute, Portland, ME (United States); Swift, Andrew H. P. [Texas Tech Univ., Lubbock, TX (United States); Thomas, Dale [Maine Maritime Academy, Castine, ME (United States); Viselli, Elizabeth [Univ. of Maine, Orono, ME (United States); Zydlewski, Gayle [Univ. of Maine, Orono, ME (United States)

2013-06-11

This is the final technical report for the U.S. Department of Energy-funded program, DE-0002981: DeepCwind Consortium Research Program. The project objective was the partial validation of coupled models and optimization of materials for offshore wind structures. The United States has a great opportunity to harness an indigenous abundant renewable energy resource: offshore wind. In 2010, the National Renewable Energy Laboratory (NREL) estimated there to be over 4,000 GW of potential offshore wind energy found within 50 nautical miles of the US coastlines (Musial and Ram, 2010). The US Energy Information Administration reported the total annual US electric energy generation in 2010 was 4,120 billion kilowatt-hours (equivalent to 470 GW) (US EIA, 2011), slightly more than 10% of the potential offshore wind resource. In addition, deep water offshore wind is the dominant US ocean energy resource available comprising 75% of the total assessed ocean energy resource as compared to wave and tidal resources (Musial, 2008). Through these assessments it is clear offshore wind can be a major contributor to US energy supplies. The caveat to capturing offshore wind along many parts of the US coast is deep water. Nearly 60%, or 2,450 GW, of the estimated US offshore wind resource is located in water depths of 60 m or more (Musial and Ram, 2010). At water depths over 60 m building fixed offshore wind turbine foundations, such as those found in Europe, is likely economically infeasible (Musial et al., 2006). Therefore floating wind turbine technology is seen as the best option for extracting a majority of the US offshore wind energy resource. Volume 1 - Test Site; Volume 2 - Coupled Models; and Volume 3 - Composite Materials

Hierarchical Diagnosis of Vocal Fold Disorders

Science.gov (United States)

Nikkhah-Bahrami, Mansour; Ahmadi-Noubari, Hossein; Seyed Aghazadeh, Babak; Khadivi Heris, Hossein

This paper explores the use of hierarchical structure for diagnosis of vocal fold disorders. The hierarchical structure is initially used to train different second-level classifiers. At the first level normal and pathological signals have been distinguished. Next, pathological signals have been classified into neurogenic and organic vocal fold disorders. At the final level, vocal fold nodules have been distinguished from polyps in organic disorders category. For feature selection at each level of hierarchy, the reconstructed signal at each wavelet packet decomposition sub-band in 5 levels of decomposition with mother wavelet of (db10) is used to extract the nonlinear features of self-similarity and approximate entropy. Also, wavelet packet coefficients are used to measure energy and Shannon entropy features at different spectral sub-bands. Davies-Bouldin criterion has been employed to find the most discriminant features. Finally, support vector machines have been adopted as classifiers at each level of hierarchy resulting in the diagnosis accuracy of 92%.

Beowawe Bottoming Binary Unit - Final Technical Report for EE0002856

Energy Technology Data Exchange (ETDEWEB)

McDonald, Dale Edward

2013-02-12

This binary plant is the first high-output refrigeration based waste heat recovery cycle in the industry. Its working fluid is environmentally friendly and as such, the permits that would be required with a butane based cycle are not necessary. The unit is modularized, meaning that the unit’s individual skids were assembled in another location and were shipped via truck to the plant site. This project proves the technical feasibility of using low temperature brine The development of the unit led to the realization of low temperature, high output, and environmentally friendly heat recovery systems through domestic research and engineering. The project generates additional renewable energy for Nevada, resulting in cleaner air and reduced carbon dioxide emissions. Royalty and tax payments to governmental agencies will increase, resulting in reduced financial pressure on local entities. The major components of the unit were sourced from American companies, resulting in increased economic activity throughout the country.

Differential diagnosis of metastases in bone scans: chemotherapy induced bone necrosis

International Nuclear Information System (INIS)

Reuland, P.

1999-01-01

Aim: Influenced by the incorrect diagnosis of a bone metastasis caused by bone necrosis we evaluated reasons and frequency of bone necrosis in patients referred for bone scanning in follow-up of tumors. Methods: Bone scans performed within two years on patients with primary bone tumors or tumors metastatic to bone were reviewed in respect to the final diagnosis bone necrosis. Results: We found the cases of three young patients who presented the appearance of hot spots on bone scintigrams which were finally diagnosed as bone necrosis. In two cases the diagnosis was based on histological findings, in one case the diagnosis was made evident by follow-up. All the three patients had been treated by chemotherapy and presented no other reason for the development of bone necrosis. Enhanced tracer uptake in all sites decreased within eight weeks up to two years without therapy. Conclusion: Single and multiple hot spots after chemotherapy may be originated by bone necrosis but mimikry metastases. (orig.) [de

Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility; FINAL

International Nuclear Information System (INIS)

Thomas B. Kirchner

2002-01-01

The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

Technical co-operation report for 2000. Report by the Director General

International Nuclear Information System (INIS)

2001-01-01

This report covers three separate topics. Part one fulfills the Agency's obligation under the General Conference resolution GC(44)/RES/18 to report on the Strengthening of Technical Co-operation. It covers the period from 1 April 2000 to 31 March 2001. The report examines the finalization of the 2001-2002 technical co-operation programme and several key concepts of the Technical Co-operation Strategy such as Partners in Development, Technical Co-operation among Developing Countries, and the continuing evolution of Regional Resource Centres. Reflecting an important trend in the technical co-operation programme, which was mandated by the General Conference, the report describes the results achieved in several programmes in least developed countries. Part two reports on the major achievements of the technical co-operation programme in 2000 in the different regions of the world. Part three presents a summary of the financial and non-financial parameters of the technical co-operation programme. The supplement to the report provides a more detailed review of resources and contributions, disbursements and non-financial indicators

Technical co-operation report for 2000. Report by the Director General

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This report covers three separate topics. Part one fulfills the Agency's obligation under the General Conference resolution GC(44)/RES/18 to report on the Strengthening of Technical Co-operation. It covers the period from 1 April 2000 to 31 March 2001. The report examines the finalization of the 2001-2002 technical co-operation programme and several key concepts of the Technical Co-operation Strategy such as Partners in Development, Technical Co-operation among Developing Countries, and the continuing evolution of Regional Resource Centres. Reflecting an important trend in the technical co-operation programme, which was mandated by the General Conference, the report describes the results achieved in several programmes in least developed countries. Part two reports on the major achievements of the technical co-operation programme in 2000 in the different regions of the world. Part three presents a summary of the financial and non-financial parameters of the technical co-operation programme. The supplement to the report provides a more detailed review of resources and contributions, disbursements and non-financial indicators.

Radiological diagnosis systems - problems and solutions

International Nuclear Information System (INIS)

Koeppe, P.

1983-01-01

An essential part of the work in a radiological diagnosis department is to produce the (written) physicians' reports. The majority is generally without any findings or ''normal pathologic'', only a minor part needs a special treatment. With respect to the quantity of this work, automation of the routine report writing was early attempted ley means of technical aids. Text processing systems and computers were used. The transition between these techniques is gradual. The article is limited to the use of computers in automation of report writing. (orig.) [de

Magnetic resonance (MR) in the diagnosis of pancreatic disease

International Nuclear Information System (INIS)

Anacker, H.; Rupp, N.; Reiser, M.; Technische Univ. Muenchen

1984-01-01

New methods of examination are measured in terms of the efficiency of their predecessors. The introduction of endoscopic retrograde cholangiopancreatography (ERCP) and computerised tomography (CT) constituted a turning point in the diagnosis of pancreatic disease. In this incipient stages as a clinical diagnostic method, the question is raised whether or not there is evidence that magnetic resonance (MR) can supplement, improve upon or replace the customary methods. It must, however, be taken into account that the technical development of MR is still in progress and that clinical experience with MR in the diagnosis of pancreatic disease, as in other areas, is still insufficient. At this point it is only possible to survey the trends. (orig.)

[Headache: classification and diagnosis].

Science.gov (United States)

Carbaat, P A T; Couturier, E G M

2016-11-01

There are many types of headache and, moreover, many people have different types of headache at the same time. Adequate treatment is possible only on the basis of the correct diagnosis. Technically and in terms of content the current diagnostics process for headache is based on the 'International Classification of Headache Disorders' (ICHD-3-beta) that was produced under the auspices of the International Headache Society. This classification is based on a distinction between primary and secondary headaches. The most common primary headache types are the tension type headache, migraine and the cluster headache. Application of uniform diagnostic concepts is essential to come to the most appropriate treatment of the various types of headache.

Role of 18F-FDG PET/CT in the diagnosis of infective endocarditis in patients with an implanted cardiac device: a prospective study

International Nuclear Information System (INIS)

Graziosi, Maddalena; Lorenzini, Massimiliano; Diemberger, Igor; Pasquale, Ferdinando; Ziacchi, Matteo; Biffi, Mauro; Martignani, Cristian; Boriani, Giuseppe; Rapezzi, Claudio; Nanni, Cristina; Bonfiglioli, Rachele; Fanti, Stefano; Bartoletti, Michele; Tumietto, Fabio; Viale, Pier Luigi

2014-01-01

Infective endocarditis (IE) is widely underdiagnosed or diagnosed after a major delay. The diagnosis is currently based on the modified DUKE criteria, where the only validated imaging technique is echocardiography, and remains challenging especially in patients with an implantable cardiac device. The aim of this study was to assess the incremental diagnostic role of 18 F-FDG PET/CT in patients with an implanted cardiac device and suspected IE. We prospectively analysed 27 consecutive patients with an implantable device evaluated for suspected device-related IE between January 2011 and June 2013. The diagnostic probability of IE was defined at presentation according to the modified DUKE criteria. PET/CT was performed as soon as possible following the clinical suspicion of IE. Patients then underwent medical or surgical treatment based on the overall clinical evaluation. During follow-up, we considered: lead cultures in patients who underwent extraction, direct inspection and lead cultures in those who underwent surgery, and a clinical/instrumental reevaluation after at least 6 months in patients who received antimicrobial treatment or had an alternative diagnosis and were not treated for IE. After the follow-up period, the diagnosis was systematically reviewed by the multidisciplinary team using the modified DUKE criteria and considering the new findings. Among the ten patients with a positive PET/CT scan, seven received a final diagnosis of ''definite IE'', one of ''possible IE'' and two of ''IE rejected''. Among the 17 patients with a negative PET/CT scan, four were false-negative and received a final diagnosis of definite IE. These patients underwent PET/CT after having started antibiotic therapy (≥48 h) or had a technically suboptimal examination. In patients with a cardiac device, PET/CT increases the diagnostic accuracy of the modified Duke criteria for IE, particularly in the subset of patients with possible IE in whom it may help the clinician manage a

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Rubiolo, Pablo R. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Conway, Lawarence E. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Oriani, Luca [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Lahoda, Edward J. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; DeSilva, Greg [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Hu, Min H. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Hartz, Josh [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Bachrach, Uriel [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Smith, Larry [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Dudek, Daniel F. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Toman, Gary J. [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Feng, Dandong [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hejzlar, Pavel [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Kazimi, Mujid S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2006-03-31

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a standard 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (~600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output.

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

International Nuclear Information System (INIS)

Rubiolo, Pablo R.; Conway, Lawarence E.; Oriani, Luca; Lahoda, Edward J.; DeSilva, Greg; Hu, Min H.; Hartz, Josh; Bachrach, Uriel; Smith, Larry; Dudek, Daniel F.; Toman, Gary J.; Feng, Dandong; Hejzlar, Pavel; Kazimi, Mujid S.

2006-01-01

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a ''standard'' 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (∼600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output

Wyoming coal-conversion project. Final technical report, November 1980-February 1982. [Proposed WyCoalGas project, Converse County, Wyoming; contains list of appendices with title and identification

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

This final technical report describes what WyCoalGas, Inc. and its subcontractors accomplished in resolving issues related to the resource, technology, economic, environmental, socioeconomic, and governmental requirements affecting a project located near Douglas, Wyoming for producing 150 Billion Btu per day by gasifying sub-bituminous coal. The report summarizes the results of the work on each task and includes the deliverables that WyCoalGas, Inc. and the subcontractors prepared. The co-venturers withdrew from the project for two reasons: federal financial assistance to the project was seen to be highly uncertain; and funds were being expended at an unacceptably high rate.

The Operator's Diagnosis Task under Abnormal Operating Conditions in Industrial Process Plant

DEFF Research Database (Denmark)

Goodstein, L.P.; Pedersen, O.M.; Rasmussen, Jens

1974-01-01

Analysis of serious accidents in connection with the operation of technical installations demonstrate that the diagnosis task which confronts personnel under non-normal plant conditions is a critical one. This report presents a preliminary outline of characteristic traits connected with the task...... of diagnosis for use in discussions of (a) the studies which are necessary in order to formulate the operator's diagnostic procedures and (b) the possibilities which exists for supporting these procedures through appropriate data processing and display in the control system. At the same time, attempts are made...

Review of technical issues related to the failure of Rosemount pressure transmitters due to fill oil loss. Final report

International Nuclear Information System (INIS)

James, R.W.; Gaertner, J.P.; Burns, E.T.; Horn, A.; Lee, L.K.

1994-08-01

Rosemount pressure transmitters are extensively used in both safety and non-safety applications in US nuclear power plants. They are used to measure pressure, flow, and water level. Rosemount pressure transmitter models 1151, 1152, 1153A, 1153, and 1154 use a fill oil to hydraulically transmit process pressure exerted on outer isolating diaphragms to internal diaphragms. The resulting deflection of the internal diaphragms changes the distance between them and a central diaphragm separating the transmitter interior into two volumes. The change in distance is measured as a change in electrical capacitance between the isolating diaphragms and the central diaphragm and can be related to differential pressure. The fill oil also functions as a dielectric. It has been well established that this fill oil can potentially leak over time, decreasing transmitter accuracy and increasing transmitter response time. Ultimately, the transmitter can fail. An extensive effort has been expended by the nuclear power industry collectively to analyze this issue and develop technically sound and reasonable requirements to mitigate the effects of oil loss in Rosemount pressure transmitters. Despite this, technical concerns have still been raised regarding the technical validity of the past analyses of this problem and its scope. In May 1993, the NRC created an internal group to comprehensively review the Rosemount issue and the NRC's action in addressing it to ensure that all available technical information has been considered. Because this issue remains of active technical interest and because the past work on this subject has been done by many different groups and organizations, EPRI has prepared this report to thoroughly document the current technical understanding of this issue, to perform additional analysis, and to identify any appropriate additional technical research activities regarding oil loss in Rosemount pressure transmitters

Final Technical Report: Results of Phase 1

Energy Technology Data Exchange (ETDEWEB)

Narang, David, J.; Hambrick, Joshua; Srinivasan, Devarajan; Ayyannar, Raja; O' Brien, Kathleen

2011-09-28

working, utility distribution feeder. To address the technical challenges related to the integration of distributed PV when PV penetration levels reach or exceed 30% of the total load, technologies and methods to ensure the stable and safe operation of the feeder will be evaluated. Lessons learned will enable APS to improve the framework for future PV integration on its system and may also aid other utilities across the United States energy sector in accelerating the adoption of distributed photovoltaic generation.

Advising students in technical projects - recognizing problem scenarios

DEFF Research Database (Denmark)

Bærentzen, Jacob Andreas; Singh, Karan

2014-01-01

In this paper, we consider the advisor’s role during the technical work and the thesis preparation for a student in the final phase of a course of study in an engineering education. We initially claim that there is a marked difference between the learning that takes place in regular course work...

Diagnosis change in voice-disordered patients evaluated by primary care and/or otolaryngology: a longitudinal study.

Science.gov (United States)

Cohen, Seth M; Dinan, Michaela A; Roy, Nelson; Kim, Jaewhan; Courey, Mark

2014-01-01

Accurate diagnosis of a voice disorder is an essential first step toward its appropriate treatment. We examined differences in laryngeal diagnosis over time in outpatients evaluated by primary care physicians (PCPs) and/or otolaryngologists. Retrospective analysis of data from a large, national administrative US claims database. Patients with laryngeal disorders based on International Classification of Diseases, Ninth Revision, Clinical Modification codes from January 1, 2004, to December 31, 2008, with at least 2 outpatient visits by a PCP and/or otolaryngologist and continuously enrolled for 12 months were included. The initial and final laryngeal diagnoses were tabulated. Of approximately 55 million individuals, 29,501 met inclusion criteria. More than half the patients in the PCP to otolaryngology group and one-third of the otolaryngology to otolaryngology group had different laryngeal diagnoses over time. Three-fourths of patients with an initial acute laryngitis diagnosis in the PCP to otolaryngology group and half of the otolaryngology to otolaryngology group had a different final laryngeal diagnosis. Of patients with a final laryngeal cancer diagnosis, one-fourth of the otolaryngology to otolaryngology group had an initial diagnosis of nonspecific dysphonia, and one-fifth of the PCP to otolaryngology group had an initial diagnosis of acute laryngitis. Differential diagnosis of voice disorders often evolves over time. The impact on treatment and health care utilization are important areas of future study.

PVWatts Version 1 Technical Reference

Energy Technology Data Exchange (ETDEWEB)

Dobos, A. P.

2013-10-01

The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

Optimización del mantenimiento preventivo, utilizando las técnicas de diagnóstico integral. Resultados finales y evaluación económica; Optimization of the Preventive Maintenance Using the Techniques of Integral Diagnosis. Final Results and Economic Evalua

Directory of Open Access Journals (Sweden)

Pedro L Hernández Domínguez

2011-02-01

Full Text Available En este trabajo se obtienen los resultados finales y la evaluación económica de la aplicación de la metodologíaque aporta el diagnóstico integral (DI, presentada por los autores en los artículos anteriores, con la finalidad deintroducir el mantenimiento basado en la condición (MBC como una forma de mejoramiento o perfeccionamientodel mantenimiento preventivo planificado (MPP que se desarrolla en las centrales termoeléctricas (CCTT cubanas. In this paper, the authors obtained the final results and the economic evaluation of the application methodologythat contributes the integral diagnosis (ID, presented by they in a previous articles, with the purpose of introducingthe condition based maintenance (CBM like a form of improvement the Planned Preventive Maintenance(PPM that is developed in the cuban thermoelectric power stations.

Glossary of technical terms for the medical technology professionals.

Directory of Open Access Journals (Sweden)

Rafael Felipe García Rodríguez

2014-03-01

Full Text Available The current work is a glossary of technical terms in English language for Medical Health Professionals, has been prepared due to the lack of technical lexicon the students have during and after their university studies, that is, the students have a deficit of technical words which limits their professional competence and accountability. This shortage limits them and makes it a great laboring challenge if they have to work overseas in English-speaking countries. The glossary comprises the main and necessary words which are needed for this type of professional in their field of action. These graduates have a solid knowledge and comprehension of biological, biochemical and biophysical fundamentals in their mother tongue but they do not have the necessary elements in the target language to operate properly. It is a need that they can work appropriately in the spheres of prevention, promotion and health recovery to support a diagnosis, a treatment and a management not only in their mother tongue but in English for their future work.

Technical indicators of financial performance in the dairy herd

DEFF Research Database (Denmark)

Kristensen, Erling Lundager; Østergaard, Søren; Krogh, Mogens Agerbo

2008-01-01

Monte Carlo simulation was used to predict the long-term financial performance related to the technical performance of dairy herds. The indicators addressed were derived from data collected routinely in the herd. They indicated technical performance that can be affected by the farmer...... or the consultant, and they were derived from expected cause-effect relations between technical performance and financial performance at the herd level. The study included the indicators shape of lactation curve, reproduction efficiency, heifer management, variation between cows in lactation curve persistency...... cow was analyzed as the measure of financial performance. The potential effects of the selected indicators on the gross margin were estimated by means of an ANOVA. The final model allowed estimation of the financial value of specific changes within the key performance indicators. This study indicated...

[Microbiological diagnosis of human immunodeficiency virus infection].

Science.gov (United States)

Álvarez Estévez, Marta; Reina González, Gabriel; Aguilera Guirao, Antonio; Rodríguez Martín, Carmen; García García, Federico

2015-10-01

This document attempts to update the main tasks and roles of the Clinical Microbiology laboratory in HIV diagnosis and monitoring. The document is divided into three parts. The first deals with HIV diagnosis and how serological testing has changed in the last few years, aiming to improve diagnosis and to minimize missed opportunities for diagnosis. Technological improvements for HIV Viral Load are shown in the second part of the document, which also includes a detailed description of the clinical significance of low-level and very low-level viremia. Finally, the third part of the document deals with resistance to antiretroviral drugs, incorporating clinical indications for integrase and tropism testing, as well as the latest knowledge on minority variants. Copyright © 2014 Elsevier España, S.L.U. y Sociedad Española de Enfermedades Infecciosas y Microbiología Clínica. All rights reserved.

HFBR: Review of the technical specifications against the FSAR

International Nuclear Information System (INIS)

Rao, D.V.; Boss, S.B.; Claiborne, E.R.; Darby, J.L.; Clark, R.A.

1990-01-01

The purpose of this review is to determine the adequacy of the High Flux Beam Reactor (HFBR) Technical Specifications for 40 MW operation by comparison with the HFBR Final Safety Analysis Report, particularly the accident analyses chapter. Specifically, the Technical Specifications were compared against the Design Basis Accident (DBA) Analyses presented in the Addendum to the HFBR FSAR for 60 MW Operation. The 60 MW DBA analyses was used since it is more current and complete than the analyses presented in the original FSAR which is considered obsolete. A listing of the required systems and equipment was made for each of the accidents analyzed. Additionally, the Technical Specification instrument setpoints were compared to the DBA analyses parametric values. Also included in this review was a comparison of the Technical Specification Bases against the FSAR and the identification of any differences. The HFBR Operations Procedures Manual (OPM) was also reviewed for any inconsistencies between the FSAR or the Technical Specifications. Upon completion of this review it was determined that the Technical Specifications are well written and the items commented on should not delay the low power restart (40 MW). Additionally, the OPM is also well written and does not require further modification before restart

Is diffusion weighted imaging adding value in diagnosis of focal hepatic lesions? Experience in 50 patients

Directory of Open Access Journals (Sweden)

Doaa Mokhtar Mohamed Emara

2014-12-01

Conclusions: DWI should be included as a basic sequence in the routine MRI study of the liver as it helps in diagnosis and so reaching a final diagnosis or at least trying to narrow the list of differential diagnosis.

Failure diagnosis using discrete event models

International Nuclear Information System (INIS)

Sampath, M.; Sengupta, R.; Lafortune, S.; Teneketzis, D.; Sinnamohideen, K.

1994-01-01

We propose a Discrete Event Systems (DES) approach to the failure diagnosis problem. We present a methodology for modeling physical systems in a DES framework. We discuss the notion of diagnosability and present the construction procedure of the diagnoser. Finally, we illustrate our approach using a Heating, Ventilation and Air Conditioning (HVAC) system

Role of {sup 18}F-FDG PET/CT in the diagnosis of infective endocarditis in patients with an implanted cardiac device: a prospective study

Energy Technology Data Exchange (ETDEWEB)

Graziosi, Maddalena; Lorenzini, Massimiliano; Diemberger, Igor; Pasquale, Ferdinando; Ziacchi, Matteo; Biffi, Mauro; Martignani, Cristian; Boriani, Giuseppe; Rapezzi, Claudio [Alma Mater-University of Bologna, and S. Orsola-Malpighi Hospital, Cardiology Unit, Department of Experimental, Diagnostic and Specialty Medicine, Bologna (Italy); Nanni, Cristina; Bonfiglioli, Rachele; Fanti, Stefano [Alma Mater-University of Bologna, and S. Orsola-Malpighi Hospital, Nuclear Medicine Unit, Department of Experimental, Diagnostic and Specialty Medicine, Bologna (Italy); Bartoletti, Michele; Tumietto, Fabio; Viale, Pier Luigi [Alma Mater-University of Bologna, and S. Orsola-Malpighi Hospital, Infectious Diseases Unit, Department of Medical and Surgical Sciences, Bologna (Italy)

2014-08-15

Infective endocarditis (IE) is widely underdiagnosed or diagnosed after a major delay. The diagnosis is currently based on the modified DUKE criteria, where the only validated imaging technique is echocardiography, and remains challenging especially in patients with an implantable cardiac device. The aim of this study was to assess the incremental diagnostic role of {sup 18}F-FDG PET/CT in patients with an implanted cardiac device and suspected IE. We prospectively analysed 27 consecutive patients with an implantable device evaluated for suspected device-related IE between January 2011 and June 2013. The diagnostic probability of IE was defined at presentation according to the modified DUKE criteria. PET/CT was performed as soon as possible following the clinical suspicion of IE. Patients then underwent medical or surgical treatment based on the overall clinical evaluation. During follow-up, we considered: lead cultures in patients who underwent extraction, direct inspection and lead cultures in those who underwent surgery, and a clinical/instrumental reevaluation after at least 6 months in patients who received antimicrobial treatment or had an alternative diagnosis and were not treated for IE. After the follow-up period, the diagnosis was systematically reviewed by the multidisciplinary team using the modified DUKE criteria and considering the new findings. Among the ten patients with a positive PET/CT scan, seven received a final diagnosis of ''definite IE'', one of ''possible IE'' and two of ''IE rejected''. Among the 17 patients with a negative PET/CT scan, four were false-negative and received a final diagnosis of definite IE. These patients underwent PET/CT after having started antibiotic therapy (≥48 h) or had a technically suboptimal examination. In patients with a cardiac device, PET/CT increases the diagnostic accuracy of the modified Duke criteria for IE, particularly in the subset of

OPERATIONS NECESSARY FOR THE DIAGNOSIS ANALYSIS OF THE ORGANIZATION

Directory of Open Access Journals (Sweden)

CAIUS LĂZĂRESCU

2014-12-01

Full Text Available The diagnosis analysis is as important as is necessary for any profit or non-profit organization, it shows the situation of the organization, helps to prevent the risks, threats and future forecast. The diagnosis analysis must present: the general situation, financial situation, human and managerial potential, technical and technological potential of the organization. Once known these aspects important for the organization, the decision or decisions can be made being aware of it and in real time. The diagnosis analysis is a procedure which is achieved in a relatively short period of time and offers solutions with global character, formulates an action program which will include detailed analysis. The high degree of complexity of the analysis needs a multidisciplinary training which can establish the method, to collect and process the data and to offer the solutions, for which this can be made by specialized companies or by specialized staff from organization self-analysis.

The SocioEconomic Analysis of Repository Siting (SEARS): Technical description: Final draft

International Nuclear Information System (INIS)

1984-11-01

Socioeconomic impacts must be assessed both for the near term and for the future. One means of addressing the need for the assessment of such impacts has been through the development of the computerized socioeconomic assessment model called the SocioEconomic Analysis of Repository Siting (SEARS) model. The SEARS model was developed for the Battelle Project Management Division. It was refined and adapted from state-of-the-art computerized projection models and thoroughly validated and is now available for use in projecting the likely socioeconomic impacts of a repository facility. This Technical Description is one of six major products that describe the SEARS modeling system. 61 refs., 11 figs., 9 tabs

Final Technical Report of the project "Controlling Quantum Information by Quantum Correlations"

Energy Technology Data Exchange (ETDEWEB)

Girolami, Davide [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-17

The report describes hypotheses, aims, methods and results of the project 20170675PRD2, “Controlling Quantum Information by Quantum Correlations”, which has been run from July 31, 2017 to January 7, 2018. The technical work has been performed by Director’s Fellow Davide Girolami of the T-4 Division, Physics of Condensed Matter and Complex Systems, under the supervision of Wojciech Zurek (T-4), Lukasz Cincio (T-4), and Marcus Daniels (CCS-7). The project ended as Davide Girolami has been converted to J. R. Oppenheimer Fellow to work on the project 20180702PRD1, “Optimal Control of Quantum Machines”, started on January 8, 2018.

Achieving Hydrogen Storage Goals through High-Strength Fiber Glass - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Li, Hong [PPG Industries, Inc., Cheswick, PA (United States); Johnson, Kenneth I. [PPG Industries, Inc., Cheswick, PA (United States); Newhouse, Norman L. [PPG Industries, Inc., Cheswick, PA (United States)

2017-06-05

Led by PPG and partnered with Hexagon Lincoln and Pacific Northwest National Laboratory (PNNL), the team recently carried out a project “Achieving Hydrogen Storage Goals through High-Strength Fiber Glass”. The project was funded by DOE’s Fuel Cell Technologies office within the Office of Energy Efficiency and Renewable Energy, starting on September 1, 2014 as a two-year project to assess technical and commercial feasibilities of manufacturing low-cost, high-strength glass fibers to replace T700 carbon fibers with a goal of reducing the composite total cost by 50% of the existing, commercial 700 bar hydrogen storage tanks used in personal vehicles.

New technologies in diagnosis of preinvasive cervical lesions

Directory of Open Access Journals (Sweden)

I. P. Aminodova

2015-01-01

Full Text Available Results of efficiency assessment of different diagnosis for preinvasive cervical lesions are represented in the article. During investigation the retrospective analysis of 353 patient histories of women with cervical intraepithelial neoplasia (primary and recurrent, who have been observed in Ivanovskiy regional oncological dispensary from 2002 to 2011, was performed. The accuracy rates of diagnosis of cervical intraepithelial neoplasia for one or several methods including cytological study, colposcopy and fluorescence cystoscopy were compared. Fluorescence diagnosis was performed with drug fotoditazin (LLC «VETA-GRAND», marketing authorisation №LS 001246 at dose of 1,0 mg/kg body weight. The final diagnosis was determined by results of histological study. The accuracy of cytological study accounted for 67,5–80,7%. Using colposcopy the exact diagnosis was determined in 67,9–74,4% of cases. Combination of cytological study with colposcopy improved the accuracy of diagnosis up to 82.1–88.9%. The superior results were for concurrent use of cytological study with colposcopy and fluorescence diagnosis – in such case the diagnosis was correct in 92,0–96,7% of patients. The analysis of results showed that using all methods of diagnosis the accuracy of diagnosis for recurrent cervical intraepithelial neoplasia was lower than for primary lesions. The decrease of diagnosis accuracy is probably related to previous diagnosis and therapeutic manipulations on cervix. Thus, multimodal diagnosis investigation with methods of fluorescence spectroscopy allows to improve accuracy of diagnosis for preinvasive cervical lesions. 

Technical procedures for land use, Deaf Smith County site, Texas: Environmental Field Program: Final draft

International Nuclear Information System (INIS)

1987-09-01

This volume contains Technical Procedures pursuant to the Land Use Site Study Plan including land use data acquisition, land use/land cover map compilation, verification of land use/land cover map accuracy, and land use/land cover data analysis. 22 refs., 5 figs

Sixth ITER technical meeting on safety and environment

International Nuclear Information System (INIS)

Saji, G.; Baker, D.

1997-01-01

The article summarizes the topics of the Sixth Technical Meeting on Safety and Environment which was held to review the first draft of the Non-Site Specific Safety Report (NSSR-2) and the draft of the ITER Final Design Report Safety Assessment (FDR-Safety) during October 27 - November 4, 1997 at the ITER San Diego Joint Work Site

Revision of the European Ecolabel Criteria for Personal, Notebook and Tablet Computers TECHNICAL REPORT Summary of the final criteria proposals

OpenAIRE

DODD NICHOLAS; VIDAL ABARCA GARRIDO CANDELA; WOLF Oliver; GRAULICH Kathrin; BUNKE Dirk; GROSS Rita; LIU Ran; MANHART Andreas; PRAKASH Siddharth

2015-01-01

This technical report provide the background information for the revision of the EU Ecolabel criteria for Personal and Notebook Computers. The study has been carried out by the Joint Research Centre with technical support from the Oeko-Institut. The work has been developed for the European Commission's Directorate General for the Environment. The main purpose of this report is to provide a summary of the technical background and rationale for each criterion proposal. This document is compl...

Risk factors for pancreatic cancer and early diagnosis of pancreatic cancer

International Nuclear Information System (INIS)

Yamao, Kenji; Mizuno, Nobumasa; Sawaki, Akira; Shimizu, Yasuhiro; Chang, K.J.

2008-01-01

This paper describes the strategy for improving the poor prognosis of the pancreatic (P) cancer by its early imaging diagnosis followed by resection, based on recent findings on its high risk group. Epidemiological studies have revealed that patients with diabetes, chronic pancreatitis, intraductal papillary-mucious tumor, P cyst, familial history of P cancer, and hereditary P cancer syndrome are involved in the high risk group of P cancer. Imaging diagnosis with CT and/or endoscopic ultrasonography (EUS) followed by histological confirmation for resection can be a useful approach to improve the prognosis in those high risk, asymptomatic individuals with abnormal levels of P enzyme and tumor marker, and with US findings of P ductal dilation and cyst. The guideline 2006 for P cancer by Japan Pancreas Society shows the algorithm leading to the final diagnosis for the positive high risk group: firstly, CT and/or MRCP (MR cholangiopancreatography (CP)); or, in case of uncertainty, EUS and/or ERCP (E retrograde CP) and/or PET; and finally, cytological, histological diagnosis. The newer approach proposed recently for the group is: multi detector row (MD)-CT and EUS; then cytodiagnosis guided by ERCP and/or with fine needle aspiration by EUS, also a promising early diagnosis. As well, molecular biological approaches are supposedly useful for the future diagnosis. (R.T.)

Technical Aspects of Telepathology with Emphasis on Future Development

Directory of Open Access Journals (Sweden)

P. Schwarzmann

2000-01-01

Full Text Available Pathology undergoes presently changes due to new developments in diagnostic opportunities and cost saving efforts in health care. Out of the wide field of telepathology the paper selects three prototype applications: telepathology in teleeducation, expert advice for preselected details of a slide and finally telepathology for remote diagnosis. The most challenging field for remote diagnosis is the application in the frozen section scenario. The paper starts with the mental experiment to map conventional procedures to counterparts in telepathology.

Laboratory Diagnosis of Pertussis

Science.gov (United States)

Schellekens, Joop F. P.; Mooi, Frits R.

2015-01-01

SUMMARY The introduction of vaccination in the 1950s significantly reduced the morbidity and mortality of pertussis. However, since the 1990s, a resurgence of pertussis has been observed in vaccinated populations, and a number of causes have been proposed for this phenomenon, including improved diagnostics, increased awareness, waning immunity, and pathogen adaptation. The resurgence of pertussis highlights the importance of standardized, sensitive, and specific laboratory diagnoses, the lack of which is responsible for the large differences in pertussis notifications between countries. Accurate laboratory diagnosis is also important for distinguishing between the several etiologic agents of pertussis-like diseases, which involve both viruses and bacteria. If pertussis is diagnosed in a timely manner, antibiotic treatment of the patient can mitigate the symptoms and prevent transmission. During an outbreak, timely diagnosis of pertussis allows prophylactic treatment of infants too young to be (fully) vaccinated, for whom pertussis is a severe, sometimes fatal disease. Finally, reliable diagnosis of pertussis is required to reveal trends in the (age-specific) disease incidence, which may point to changes in vaccine efficacy, waning immunity, and the emergence of vaccine-adapted strains. Here we review current approaches to the diagnosis of pertussis and discuss their limitations and strengths. In particular, we emphasize that the optimal diagnostic procedure depends on the stage of the disease, the age of the patient, and the vaccination status of the patient. PMID:26354823

The Laboratory Diagnosis of Bacterial Vaginosis

Directory of Open Access Journals (Sweden)

Deborah Money

2005-01-01

Full Text Available Bacterial vaginosis (BV is an extremely common health problem for women. In addition to the troublesome symptoms often associated with a disruption in the balance of vaginal flora, BV is associated with adverse gynecological and pregnancy outcomes. Although not technically a sexually transmitted infection, BV is a sexually associated condition. Diagnostic tests include real-time clinical/microbiological diagnosis, and the current gold standard, the standardized evaluation of morphotypes on Gram stain analysis. The inappropriate use of vaginal culture can be misleading. Future developments into molecular-based diagnostics will be important to further understand this complex endogenous flora disruption.

Technical and economic feasibility of thermal storage. Final report

Energy Technology Data Exchange (ETDEWEB)

Shelpuk, B.; Joy, P.; Crouthamel, M.

1977-06-01

The technical and economic feasibility of various thermal energy storage alternatives is determined by comparing the system performance and annualized cost which result from each storage alternative operating with the same solar collector model, the same building load model, and the same heating system and controls model. Performance and cost calculations are made on the basis of an hour-by-hour time step using actual weather bureau data for Albuquerque, N. M., and New York City for a single six-month heating season. The primary approach to comparing various storage alternatives is to allow the collector area and storage mass to vary until a minimum cost combination is achieved. In the Albuquerque location collector area of 325 ft/sup 2/, water storage mass of 12.5 lb/ft/sup 2/ of collector area, and phase change mass of 6.25 lb/ft/sup 2/ of collector area results in minimum cost systems, each of which delivers about 50% of the total building demand. The primary conclusion is that, using current costs for materials and containers, water is the cheapest storage alternative for heating applications in both Albuquerque and New York City. The cost of containing or encapsulating phase change materials, coupled with their small system performance advantage, is the main reason for this conclusion. The use of desiccant materials for thermal storage is considered to be impractical due to irreversibilities in thermal cycling.

Application of artificial neural network for NHR fault diagnosis

International Nuclear Information System (INIS)

Yu Haitao; Zhang Liangju; Xu Xiangdong

1999-01-01

The author makes researches on 200 MW nuclear heating reactor (NHR) fault diagnosis system using artificial neural network, and use the tendency value and real value of the data under the accidents to train and test two BP networks respectively. The final diagnostic result is the combination of the results of the two networks. The compound system can enhance the accuracy and adaptability of the diagnosis comparing to the single network system

Strategies for reactor safety: Preventing loss of coolant accidents. Final report

International Nuclear Information System (INIS)

Lydell, B.O.Y.

1997-12-01

This final report on the NKS/RAK-1.2 summarizes the main features of the PIFRAP PC-program and its intended implementation. Regardless of the preferred technical approach to LOCA frequency estimation, the analysis approach must include recognition of the following technical issues: a) Degradation and failure mechanisms potentially affecting piping systems within the reactor coolant pressure boundary (RCPB) and the potential consequences; b) In-service inspection practices and how they influence piping reliability; and c) The service experience with piping systems. The report consists of six sections and one appendix. A Nordic perspective on LOCA and nuclear safety is given. It includes summaries of results from research in material sciences and current regulatory philosophies regarding piping reliability. A summary of the LOCA concept is applied in Nordic PSA studies. It includes a discussion on deterministic and probabilistic views on LOCA. The R and D on piping reliability by SKI and the PIFRAP model is summarized. Next, Section 6 presents conclusion and recommendations. Finally, Appendix A contains a list of abbreviations and acronyms, together with a glossary of technical terms. (EG)

Randomized controlled trial of endoscopic ultrasound-guided fine-needle sampling with or without suction for better cytological diagnosis

DEFF Research Database (Denmark)

Puri, Rajesh; Vilmann, Peter; Saftoiu, Adrian

2009-01-01

). The samples were characterized for cellularity and bloodiness, with a final cytology diagnosis established blindly. The final diagnosis was reached either by EUS-FNA if malignancy was definite, or by surgery and/or clinical follow-up of a minimum of 6 months in the cases of non-specific benign lesions...

Anxiety disorders: diagnosis and treatment.

Science.gov (United States)

Jack, R A; Mathew, R J

1985-07-01

Pathologic anxiety, marked by inappropriate apprehension and/or fear, causes patients to seek help. Anxiety is associated with a wide variety of physical illnesses, and these must be initially considered when making a diagnosis. Similarly, anxiety associated with a wide variety of psychiatric syndromes must also be considered. Finally, the possibility of transient situational anxiety is ever present. Once it is determined that a primary anxiety disorder exists, then the presence or absence of phobias, panic attacks, and chronic "free-floating" anxiety will fully characterize the disorder. With an accurate diagnosis in hand, a multifaceted treatment approach can be designed. Effective treatments now exist for phobic and panic disorders, and more effective treatment for chronic generalized anxiety may be forthcoming.

Reappraising entrapment neuropathies--mechanisms, diagnosis and management.

Science.gov (United States)

Schmid, Annina B; Nee, Robert J; Coppieters, Michel W

2013-12-01

The diagnosis of entrapment neuropathies can be difficult because symptoms and signs often do not follow textbook descriptions and vary significantly between patients with the same diagnosis. Signs and symptoms which spread outside of the innervation territory of the affected nerve or nerve root are common. This Masterclass provides insight into relevant mechanisms that may account for this extraterritorial spread in patients with entrapment neuropathies, with an emphasis on neuroinflammation at the level of the dorsal root ganglia and spinal cord, as well as changes in subcortical and cortical regions. Furthermore, we describe how clinical tests and technical investigations may identify these mechanisms if interpreted in the context of gain or loss of function. The management of neuropathies also remains challenging. Common treatment strategies such as joint mobilisation, neurodynamic exercises, education, and medications are discussed in terms of their potential to influence certain mechanisms at the site of nerve injury or in the central nervous system. The mechanism-oriented approach for this Masterclass seems warranted given the limitations in the current evidence for the diagnosis and management of entrapment neuropathies. Copyright © 2013 Elsevier Ltd. All rights reserved.

Confocal laser endomicroscopy for diagnosis of Barrett´s esophagus

Directory of Open Access Journals (Sweden)

Helmut eNeumann

2012-05-01

Full Text Available Barrett´s esophagus (BE is established as a premalignant condition in the distal esophagus. Current surveillance guidelines recommend random biopsies every 1-2 cm at intervals of 3-5 years. Advanced endoscopic imaging of BE underwent several technical revolutions within the last decade including broad-field (red-flag techniques (e.g. chromoendoscopy and small-field techniques with confocal laser endomicroscopy (CLE at the forefront. In this review we will focus on advanced endoscopic imaging using CLE for the diagnosis and characterization of BE and associated neoplasia. In addition, we will critically discuss the technique of CLE and provide some tricks and hints for the daily routine practice of CLE for diagnosis of BE.

Final Technical Report - DE-EE0003542

Energy Technology Data Exchange (ETDEWEB)

Haley, James D

2013-03-31

Wind has provided energy for thousands of years: some of the earliest windmill engineering designs date back to ancient Babylonia and India where wind would be used as a source of irrigation. Today, wind is the quickest growing resource in Americas expanding energy infrastructure. However, to continue to positively diversify Americas energy portfolio and further reduce the countrys reliance of foreign oil, the industry must grow substantially over the next two decades in both turbine installations and skilled industrial manpower to support. The wind sector is still an emergent industry requiring maturation and development of its labor force: dedicated training is needed to provide the hard and soft skills to support the increasingly complex wind turbine generators as the technology evolves. Furthermore, the American workforce is facing a steep decline in available labor resources as the baby boomer generation enters retirement age. It is therefore vital that a process is quickly created for supporting the next generation of wind technicians. However, the manpower growth must incorporate three key components. First, the safety and technical training curriculum must be standardized across the industry - current wind educational programs are disparate and dedicated standardization programs must be further refined and implemented. Second, it is essential that the wind sector avoid disrupting other energy production industries by cannibalizing workers, which would indirectly affect the rest of Americas energy portfolio. The future wind workforce must be created organically utilizing either young people entering the workforce or train personnel emerging from careers outside of energy production. Third, the training must be quick and efficient as large amounts of wind turbines are being erected each year and this growth is expected to continue until at least 2035. One source that matches these three requirements is personnel transitioning from military service to the

Advanced Beta Dosimetry Techniques.Final Scientific/Technical Report

International Nuclear Information System (INIS)

David M. Hamby, PhD

2006-01-01

Final report describing NEER research on Advanced Beta Dosimetry Techniques. The research funded by this NEER grant establishes the framework for a detailed understanding of the challenges in beta dosimetry, especially in the presence of a mixed radiation field. The work also stimulated the thinking of the research group which will lead to new concepts in digital signal processing to allow collection of detection signals and real-time analysis such that simultaneous beta and gamma spectroscopy can take place. The work described herein (with detail in the many publications that came out of this research) was conducted in a manner that provided dissertation and thesis topics for three students, one of which was completely funded by this grant. The overall benefit of the work came in the form of a dramatic shift in signal processing that is normally conducted in pulse shape analysis. Analog signal processing was shown not to be feasible for this type of work and that digital signal processing was a must. This, in turn, led the research team to a new understanding of pulse analysis, one in which expands the state-of-the-art in simultaneous beta and gamma spectroscopy with a single detector

Sustainability Logistics Basing - Science and Technology Objective - Demonstration; Industry Assessment and Demonstration Final Report

Science.gov (United States)

2017-08-14

TECHNICAL REPORT AD ________________ NATICK/TR-17/019 SUSTAINABILITY ...LOGISTICS BASING – SCIENCE & TECHNOLOGY OBJECTIVE – DEMONSTRATION; INDUSTRY ASSESSMENT AND DEMONSTRATION FINAL REPORT by Elizabeth D. Swisher and...Benjamin J. Campbell August 2017 Final Report December 2014 – February 2016 Approved for public release; distribution is

Development of High-Performance Cast Crankshafts. Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bauer, Mark E [General Motors, Detroit, MI (United States)

2017-03-31

The objective of this project was to develop technologies that would enable the production of cast crankshafts that can replace high performance forged steel crankshafts. To achieve this, the Ultimate Tensile Strength (UTS) of the new material needs to be 850 MPa with a desired minimum Yield Strength (YS; 0.2% offset) of 615 MPa and at least 10% elongation. Perhaps more challenging, the cast material needs to be able to achieve sufficient local fatigue properties to satisfy the durability requirements in today’s high performance gasoline and diesel engine applications. The project team focused on the development of cast steel alloys for application in crankshafts to take advantage of the higher stiffness over other potential material choices. The material and process developed should be able to produce high-performance crankshafts at no more than 110% of the cost of current production cast units, perhaps the most difficult objective to achieve. To minimize costs, the primary alloy design strategy was to design compositions that can achieve the required properties with minimal alloying and post-casting heat treatments. An Integrated Computational Materials Engineering (ICME) based approach was utilized, rather than relying only on traditional trial-and-error methods, which has been proven to accelerate alloy development time. Prototype melt chemistries designed using ICME were cast as test specimens and characterized iteratively to develop an alloy design within a stage-gate process. Standard characterization and material testing was done to validate the alloy performance against design targets and provide feedback to material design and manufacturing process models. Finally, the project called for Caterpillar and General Motors (GM) to develop optimized crankshaft designs using the final material and manufacturing processing path developed. A multi-disciplinary effort was to integrate finite element analyses by engine designers and geometry-specific casting

Evaluation of the feasibility, economic impact, and effectiveness of underground nuclear power plants. Final technical report

International Nuclear Information System (INIS)

1978-05-01

Information on underground nuclear power plants is presented concerning underground nuclear power plant concepts; public health impacts; technical feasibility of underground concepts; economic impacts of underground construction; and evaluation of related issues

Evaluation of Outcome- Prenatal Diagnosis Indication and Results Suitability in Families Referred to our Laboratory For Prenatal Diagnosis

Directory of Open Access Journals (Sweden)

Ayşegül Türkyılmaz

2007-01-01

Full Text Available Since our aim is to establish the importance, necessity and concept of prenatal diagnosis in our region and supply routine service at a stage which we admit as a transitional period for application, all of the materials of amniocentesis, cordocentesis and corion villi sample referred to laboratories were evaluated without refusal.When we examined prenatal diagnoses of these specimens, we found Down Risk (according to triple test result in 164 specimens (%34, fetal anomaly risk in 122 (%25, advanced age in 69 (%14 poor-obstetric anamnesis in 27(%5, Down Syndrome- infant history in 20 (%4, family request in 17, and habitual abortus (%3 etc. in specimens. Lymphocyte Culture prepared in duplicate for each specimen and chromosome were obtained from total of ten slides for each specimen. Slides were stained with Giemsa Banding Technic (GTG Banding. Total (10x481 4810 slides were evaluated for diagnosis.There were no false positive and false negative results.

Utility of Gram staining for diagnosis of Malassezia folliculitis.

Science.gov (United States)

Tu, Wei-Ting; Chin, Szu-Ying; Chou, Chia-Lun; Hsu, Che-Yuan; Chen, Yu-Tsung; Liu, Donald; Lee, Woan-Ruoh; Shih, Yi-Hsien

2018-02-01

Malassezia folliculitis (MalF) mimics acne vulgaris and bacterial folliculitis in clinical presentations. The role of Gram staining in rapid diagnosis of MalF has not been well studied. In our study, 32 patients were included to investigate the utility of Gram staining for MalF diagnosis. The final diagnoses of MalF were determined according to clinical presentation, pathological result and treatment response to antifungal agents. Our results show that the sensitivity and specificity of Gram staining are 84.6% and 100%, respectively. In conclusion, Gram staining is a rapid, non-invasive, sensitive and specific method for MalF diagnosis. © 2017 Japanese Dermatological Association.

75 FR 61619 - Safety Zone; IJSBA World Finals, Lower Colorado River, Lake Havasu, AZ

Science.gov (United States)

2010-10-06

... Sports Boating Association (IJSBA) World Finals. This temporary safety zone is necessary to provide for... International Jet Sports Boating Association (IJSBA) is sponsoring the IJSBA World Finals. The event will... 13211. Technical Standards The National Technology Transfer and Advancement Act (NTTAA) (15 U.S.C. 272...

76 FR 16531 - Technical Correction for Neurological Listing Cross-Reference

Science.gov (United States)

2011-03-24

... 1-800-325-0778, or visit our Internet site, Social Security Online, at http://www.socialsecurity.gov... SOCIAL SECURITY ADMINISTRATION 20 CFR Part 404 [Docket No. SSA-2011-0019] RIN 0960-AH33 Technical Correction for Neurological Listing Cross-Reference AGENCY: Social Security Administration. ACTION: Final...

Anterior cysts of the spine: a difficult differential diagnosis to amyotrophic lateral sclerosis.

Science.gov (United States)

Schmalbach, S; Petri, S; Götz, F; Dengler, R; Krampfl, K

2008-11-01

We describe three patients referred to our ALS/MND clinic with suspected diagnosis of amyotrophic lateral sclerosis (ALS). The patients were all male, middle aged, and their initial symptoms were weakness and fasciculations in upper limb muscles. Results of clinical and electrophysiological examination in all cases were in accordance with possible ALS according to the revised El Escorial criteria. Other conditions mimicking ALS appeared to be excluded by extensive technical examinations and laboratory tests. Only repeated MRI examinations revealed anterior spinal cysts several years after symptom onset. This report intends to highlight this rare and difficult differential diagnosis of ALS and underlines the value of the revised El Escorial criteria in conjunction with electrophysiology to asses the certainty of the diagnosis ALS.

Swallowable Wireless Capsule Endoscopy: Progress and Technical Challenges

Directory of Open Access Journals (Sweden)

Guobing Pan

2012-01-01

Full Text Available Wireless capsule endoscopy (WCE offers a feasible noninvasive way to detect the whole gastrointestinal (GI tract and revolutionizes the diagnosis technology. However, compared with wired endoscopies, the limited working time, the low frame rate, and the low image resolution limit the wider application. The progress of this new technology is reviewed in this paper, and the evolution tendencies are analyzed to be high image resolution, high frame rate, and long working time. Unfortunately, the power supply of capsule endoscope (CE is the bottleneck. Wireless power transmission (WPT is the promising solution to this problem, but is also the technical challenge. Active CE is another tendency and will be the next geneion of the WCE. Nevertheless, it will not come true shortly, unless the practical locomotion mechanism of the active CE in GI tract is achieved. The locomotion mechanism is the other technical challenge, besides the challenge of WPT. The progress about the WPT and the active capsule technology is reviewed.

Final Technical Report 09 LW 112

Energy Technology Data Exchange (ETDEWEB)

Lenhoff, R J

2010-11-28

Since the development of new antibiotics is out-paced by the emergence of bacterial resistance to existing antibiotics, it is crucial to understand the genetic mechanisms underlying resistance existing antibiotics. At the center of this mystery is a poorly understood phenomenon, heteroresistance: the coexistence of multiple subpopulations with varying degrees of antibiotic resistance. A better understanding of the fundamental basis of heteroresistance could result in sorely needed breakthroughs in treatment options. This project proposed to leverage a novel microfluidic (microchemostat) technology to probe the heteroresistance phenomenon in bacteria, with the aim of restoring the efficacy of existing {beta}-lactam antibiotics. The clinically important bacteria Methicillin Resistant S. aureus (MRSA) was used as the test case of bacteria that exhibits antibiotic heteroresistance. MRSA is difficult to treat because it is resistant to all {beta}-lactam antibiotics, as well as other classes of antimicrobials. Whereas {beta}-lactams such as methicillin and oxacillin are the preferred antibiotics to treat S. aureus infections due to their efficacy and low side effects, accurate determination and use of oxacillin/methicillin dosage is hampered by heteroresistance. In fact, invasive MRSA infections now account for about 95,000 deaths per year, a number that exceeds the deaths due to either influenza or HIV (12). In some MRSA strains, two subpopulations of cells may coexist: both populations carry the mecA gene that confers resistance, but mecA is differentially expressed so that only a small number of cells are observed during in vitro testing. Why this occurs is not understood. Prior experiments have sought to explain this phenomenon with conflicting results, with technology being the primary barrier to test the system sufficiently. This is the final report on work accomplished under the Lab-wide LDRD project 09-LW-112. This project was awarded to Frederick Balagadde who

78 FR 17871 - Changes To Implement the Technical Corrections to the Leahy-Smith America Invents Act as to Inter...

Science.gov (United States)

2013-03-25

... Business Method Patents--Definition of Technological Invention, 77 FR 48734 (Aug. 14, 2012) (final rule... Inter Partes Review AGENCY: United States Patent and Trademark Office, Commerce. ACTION: Final rule..., United States Code (``AIA Technical Corrections Act''). Consistent with the statutory changes, this final...

Importance of spontaneous nystagmus detection in the differential diagnosis of acute vertigo.

Science.gov (United States)

Pavlin-Premrl, Davor; Waterston, John; McGuigan, Sean; Infeld, Bernard; Sultana, Ron; O'Sullivan, Richard; Gerraty, Richard P

2015-03-01

Vertigo is a common cause of emergency department attendance. Detection of spontaneous nystagmus may be a useful sign in distinguishing vestibular neuritis from other vestibular diagnoses. We aimed to assess the contribution of spontaneous nystagmus in the diagnosis of acute vertigo. We enrolled consecutive consenting patients arriving at a single emergency department with acute vertigo. There was no declared protocol for the emergency department staff. A standardized history and examination was conducted by the investigators. Observation for spontaneous nystagmus, its response to visual fixation, and testing the vestibulo-ocular reflex with the horizontal head impulse test were the chief examination components. MRI was obtained within 24 hours. Clinical criteria and MRI were used to reach the final diagnosis. The investigators' physical findings and final neurological diagnosis were compared with the initial emergency department examination findings and the referral diagnosis. There were 28 patients, 15 with vestibular neuritis, six with benign paroxysmal positional vertigo, one with stroke, suspected clinically, and three with migraine. In three the diagnosis remained uncertain. Spontaneous nystagmus was seen in all 15 patients with vestibular neuritis, fixation-suppressed in eight of 11 tested for this. The head impulse test was positive in 12 of 15 with vestibular neuritis. The emergency department referral diagnosis was correct in six of 23 patients. The ability to detect spontaneous nystagmus is useful in vestibular diagnosis, both in support of a diagnosis of vestibular neuritis and in avoiding false positive diagnoses of benign paroxysmal positional vertigo. Copyright © 2014 Elsevier Ltd. All rights reserved.

Modern problems of perfection of elite light athletic sportsmen’s technical skillfulness perfection

Directory of Open Access Journals (Sweden)

A.V. Kolot

2016-04-01

Full Text Available Purpose: perfection of elite sportsmen’s technical skillfulness in competition kinds of light athletic. Material: the data of more than 60 literature sources were systemized. Expert questioning of 36 coaches, having experience of work with elite sportsmen, was carried out; documents of training process planning were analyzed as well as sportsmen’s diaries (n=244. Results: we have presented main principles of sportsmen’s technical skillfulness perfection and elucidated characteristics of technical training methodic. We have determined main priorities of technical training building for light athletes at every stage of many years’ perfection. Dynamic of competition practice volume has been found as well as main requirements to selection of training means of technical orientation. The data of bio-mechanical criteria of sportsmen’s technical skillfulness assessment have been supplemented. Conclusions: effectiveness of sportsmen’s training methodic is determined by realization of previous stages’ technical potential in final competition results. It can be achieved by determination of means of and methods of different orientation rational correlation.

Modern problems of perfection of elite light athletic sportsmen’s technical skillfulness perfection

Directory of Open Access Journals (Sweden)

Kolot A.V.

2016-02-01

Full Text Available Purpose: perfection of elite sportsmen’s technical skillfulness in competition kinds of light athletic. Material: the data of more than 60 literature sources were systemized. Expert questioning of 36 coaches, having experience of work with elite sportsmen, was carried out; documents of training process planning were analyzed as well as sportsmen’s diaries (n=244. Results: we have presented main principles of sportsmen’s technical skillfulness perfection and elucidated characteristics of technical training methodic. We have determined main priorities of technical training building for light athletes at every stage of many years’ perfection. Dynamic of competition practice volume has been found as well as main requirements to selection of training means of technical orientation. The data of bio-mechanical criteria of sportsmen’s technical skillfulness assessment have been supplemented. Conclusions: effectiveness of sportsmen’s training methodic is determined by realization of previous stages’ technical potential in final competition results. It can be achieved by determination of means of and methods of different orientation rational correlation.

NASA Space Environments Technical Discipline Team Space Weather Activities

Science.gov (United States)

Minow, J. I.; Nicholas, A. C.; Parker, L. N.; Xapsos, M.; Walker, P. W.; Stauffer, C.

2017-12-01

The Space Environment Technical Discipline Team (TDT) is a technical organization led by NASA's Technical Fellow for Space Environments that supports NASA's Office of the Chief Engineer through the NASA Engineering and Safety Center. The Space Environments TDT conducts independent technical assessments related to the space environment and space weather impacts on spacecraft for NASA programs and provides technical expertise to NASA management and programs where required. This presentation will highlight the status of applied space weather activities within the Space Environment TDT that support development of operational space weather applications and a better understanding of the impacts of space weather on space systems. We will first discuss a tool that has been developed for evaluating space weather launch constraints that are used to protect launch vehicles from hazardous space weather. We then describe an effort to better characterize three-dimensional radiation transport for CubeSat spacecraft and processing of micro-dosimeter data from the International Space Station which the team plans to make available to the space science community. Finally, we will conclude with a quick description of an effort to maintain access to the real-time solar wind data provided by the Advanced Composition Explorer satellite at the Sun-Earth L1 point.

Standard technical specifications: Babcock and Wilcox Plants. Revision 1

International Nuclear Information System (INIS)

1995-04-01

This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Babcock ampersand Wilcox Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

A final step towards the European wind loading code

NARCIS (Netherlands)

Staalduinen, P.C. van; Geurts, C.P.W.

1999-01-01

The process of the transition of national wind loading codes into a European Prestandard ENV 1991-2-4 for wind loading is being discussed. Backgrounds of this undertaking are being explained and specific technical issues to be resolved when drafting the final version of a European Standard for Wind

Integrated Technical Information for the Air Logistics Center: Enhancing Maintenance Technician Task Performance

National Research Council Canada - National Science Library

Mitta, Deborah

1998-01-01

This technical paper documents the final results of an analysis of the task environment under which depot maintenance technicians perform their jobs--specifically, programmed depot maintenance (PDM) for F-15 aircraft...

A COMPARATIVE STUDY OF PREOPERATIVE DIAGNOSIS AND PATHOLOGICAL DIAGNOSIS IN ADRENAL SWELLINGS

Directory of Open Access Journals (Sweden)

Saju P. R

2017-05-01

Full Text Available BACKGROUND The adrenal gland neoplasms include primary and metastatic malignant tumours. They can be functional or non-functional and also detected as incidentaloma lesions. Advanced imaging often reveals adrenal tumours and tumour-like conditions in both symptomatic and asymptomatic patients. Even with the functional study and advanced imaging, preoperative diagnosis is always challenging. MATERIALS AND METHODS A retrospective study of adrenal tumours performed during July 2014-April 2016 was done. Total 7 cases were included. Case records and histopathology reports were reviewed to collect data. RESULTS Majority were females (85% with mean age of 50 years. 71% patients presented symptomatically and incidentaloma was noticed in 29%. Functional tumours were found in 71%. 42% discrepancy were noted between the radiological and final histopathological findings. 28% noted in benign lesions and 14% in malignant conditions. CONCLUSION In the current era, even though imaging can aid in diagnosis, histopathology still remains as gold standard investigation in adrenal tumours.

Pathways to diagnosis: exploring the experiences of problem recognition and obtaining a dementia diagnosis among Anglo-Canadians.

Science.gov (United States)

Leung, Karen K; Finlay, Juli; Silvius, James L; Koehn, Sharon; McCleary, Lynn; Cohen, Carole A; Hum, Susan; Garcia, Linda; Dalziel, William; Emerson, Victor F; Pimlott, Nicholas J G; Persaud, Malini; Kozak, Jean; Drummond, Neil

2011-07-01

Increasing evidence suggests that early diagnosis and management of dementia-related symptoms may improve the quality of life for patients and their families. However, individuals may wait from 1-3 years from the onset of symptoms before receiving a diagnosis. The objective of this qualitative study was to explore the perceptions and experiences of problem recognition, and the process of obtaining a diagnosis among individuals with early-stage dementia and their primary carers. From 2006-2009, six Anglo-Canadians with dementia and seven of their carers were recruited from the Alzheimer's Society of Calgary to participate in semi-structured interviews. Using an inductive, thematic approach to the analysis, five major themes were identified: becoming aware of memory problems, attributing meanings to symptoms, initiating help-seeking, acknowledging the severity of cognitive changes and finally obtaining a definitive diagnosis. Individuals with dementia reported noticing memory difficulties earlier than their carers. However, initial symptoms were perceived as ambiguous, and were normalised and attributed to concurrent health problems. The diagnostic process was typically characterised by multiple visits and interactions with health professionals, and a diagnosis was obtained as more severe cognitive deficits emerged. Throughout the diagnostic pathway, carers played dynamic roles. Carers initially served as a source of encouragement to seek help, but they eventually became actively involved over concerns about alternative diagnoses and illness management. A better understanding of the pre-diagnosis period, and the complex interactions between people's beliefs and attributions about symptoms, may elucidate some of the barriers as well as strategies to promote a timelier dementia diagnosis. © 2011 Blackwell Publishing Ltd.

Diagnosis delay in Libyan female breast cancer.

Science.gov (United States)

Ermiah, Eramah; Abdalla, Fathi; Buhmeida, Abdelbaset; Larbesh, Entesar; Pyrhönen, Seppo; Collan, Yrjö

2012-08-21

To study the diagnosis delay and its impact on stage of disease among women with breast cancer on Libya. 200 women, aged 22 to 75 years with breast cancer diagnosed during 2008-2009 were interviewed about the period from the first symptoms to the final histological diagnosis of breast cancer. This period (diagnosis time) was categorized into 3 periods: 6 months. If diagnosis time was longer than 3 months, the diagnosis was considered delayed (diagnosis delay). Consultation time was the time taken to visit the general practitioner after the first symptoms. Retrospective preclinical and clinical data were collected on a form (questionnaire) during an interview with each patient and from medical records. The median of diagnosis time was 7.5 months. Only 30.0% of patients were diagnosed within 3 months after symptoms. 14% of patients were diagnosed within 3-6 months and 56% within a period longer than 6 months. A number of factors predicted diagnosis delay: Symptoms were not considered serious in 27% of patients. Alternative therapy (therapy not associated with cancer) was applied in 13.0% of the patients. Fear and shame prevented the visit to the doctor in 10% and 4.5% of patients, respectively. Inappropriate reassurance that the lump was benign was an important reason for prolongation of the diagnosis time. Diagnosis delay was associated with initial breast symptom(s) that did not include a lump (p diagnosis, the clinical stage distribution was as follows: 9.0% stage I, 25.5% stage II, 54.0% stage III and 11.5% stage IV.Diagnosis delay was associated with bigger tumour size (p Diagnosis delay is very serious problem in Libya. Diagnosis delay was associated with complex interactions between several factors and with advanced stages. There is a need for improving breast cancer awareness and training of general practitioners to reduce breast cancer mortality by promoting early detection. The treatment guidelines should pay more attention to the early phases of breast

Prenatal diagnosis of fetal skeletal dysplasia with 3D CT

International Nuclear Information System (INIS)

Miyazaki, Osamu; Horiuchi, Tetsuya; Nishimura, Gen; Sago, Haruhiko; Hayashi, Satoshi; Kosaki, Rika

2012-01-01

Clinical use of 3D CT for fetal skeletal malformations is controversial. The purpose of this study was to evaluate the efficacy of fetal 3D CT using three protocols with different radiation doses and through comparing findings between fetal CT and conventional postnatal radiographic skeletal survey. Seventeen fetuses underwent CT for suspected skeletal dysplasia. A relay of three CT protocols with stepwise dose-reduction were used over the study period. The concordance between the CT diagnosis and the final diagnosis was assessed. Ninety-three radiological findings identifiable on radiographs were compared with CT. Fetal CT provided the correct diagnosis in all 17 fetuses, the detectability rate of cardinal findings was 93.5 %. In 59 % of the fetuses an US-based diagnosis was changed prenatally due to CT findings. The estimated fetal radiation dose in the final protocol was 3.4 mSv (50 %) of the initial protocol, and this dose reduction did not result in degraded image quality. The capability of fetal CT to delineate the skeleton was almost the same as that of postnatal skeletal survey. The perinatal management was altered due to these more specific CT findings, which aided in counseling and in the management of the pregnancy. (orig.)

Prenatal diagnosis of fetal skeletal dysplasia with 3D CT

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, Osamu; Horiuchi, Tetsuya [National Center for Child Health and Development, Department of Radiology, Seatagaya-ku, Tokyo (Japan); Nishimura, Gen [Tokyo Metropolitan Children' s Medical Center, Department of Pediatric Imaging, Fuchu-shi, Tokyo (Japan); Sago, Haruhiko; Hayashi, Satoshi [National Center for Child Health and Development, Department of Perinatal Medicine and Maternal Care, Seatagaya-ku, Tokyo (Japan); Kosaki, Rika [National Center for Child Health and Development, Department of Strategic Medicine, Division of Clinical Genetics and Molecular Medicine, Seatagaya-ku, Tokyo (Japan)

2012-07-15

Clinical use of 3D CT for fetal skeletal malformations is controversial. The purpose of this study was to evaluate the efficacy of fetal 3D CT using three protocols with different radiation doses and through comparing findings between fetal CT and conventional postnatal radiographic skeletal survey. Seventeen fetuses underwent CT for suspected skeletal dysplasia. A relay of three CT protocols with stepwise dose-reduction were used over the study period. The concordance between the CT diagnosis and the final diagnosis was assessed. Ninety-three radiological findings identifiable on radiographs were compared with CT. Fetal CT provided the correct diagnosis in all 17 fetuses, the detectability rate of cardinal findings was 93.5 %. In 59 % of the fetuses an US-based diagnosis was changed prenatally due to CT findings. The estimated fetal radiation dose in the final protocol was 3.4 mSv (50 %) of the initial protocol, and this dose reduction did not result in degraded image quality. The capability of fetal CT to delineate the skeleton was almost the same as that of postnatal skeletal survey. The perinatal management was altered due to these more specific CT findings, which aided in counseling and in the management of the pregnancy. (orig.)

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

W. C. Griffith

2007-01-01

In this project we provide an example of how to develop multi-tiered models to go across levels of biological organization to provide a framework for relating results of studies of low doses of ionizing radiation. This framework allows us to better understand how to extrapolate laboratory results to policy decisions, and to identify future studies that will increase confidence in policy decisions. In our application of the conceptual Model we were able to move across multiple levels of biological assessment for rodents going from molecular to organism level for in vitro and in vivo endpoints and to relate these to human in vivo organism level effects. We used the rich literature on the effects of ionizing radiation on the developing brain in our models. The focus of this report is on disrupted neuronal migration due to radiation exposure and the structural and functional implications of these early biological effects. The cellular mechanisms resulting in pathogenesis are most likely due to a combination of the three mechanisms mentioned. For the purposes of a computational model, quantitative studies of low dose radiation effects on migration of neuronal progenitor cells in the cerebral mantle of experimental animals were used. In this project we were able to show now results from studies of low doses of radiation can be used in a multidimensional framework to construct linked models of neurodevelopment using molecular, cellular, tissue, and organ level studies conducted both in vitro and in vivo in rodents. These models could also be linked to behavioral endpoints in rodents which can be compared to available results in humans. The available data supported modeling to 10 cGy with limited data available at 5 cGy. We observed gradual but non-linear changes as the doses decreased. For neurodevelopment it appears that the slope of the dose response decreases from 25 cGy to 10 cGy. Future studies of neurodevelopment should be able to better define the dose response in this range.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacquelyn Yanch

2006-05-22

This project involved the development of a method for in vivo prompt gamma neutron activation analysis for the investigation of Boron-10 distribution in a rabbit knee. The overall objective of this work was a robust approach for rapid screening of new {sup 10}B-labelled compounds to determine their suitability for use in the treatment of rheumatoid arthritis via Boron Neutron Capture Synovectomy (BNCS). For BNCS it is essential to obtain a compound showing high uptake levels in the synovium and long residence time in the joints. Previously the in vivo uptake behavior of potential compounds was evaluated in the arthritic knee joints of rabbits via extensive dissection studies. These studies are very labor-intensive and involve sacrificing large numbers of animals. An in vivo {sup 10}B screening approach was developed to provide initial evaluation of potential compounds. Only those compounds showing positive uptake and retention characteristics will be evaluated further via dissection studies. No further studies will be performed with compounds showing rapid clearance and/or low synovial uptake. Two approaches to in vivo screening were investigated using both simulation methods and experimentation. Both make use of neutron beams generated at the MIT Research Reactor. The first, Transmission Computed Tomography (TCT) was developed and tested but was eventually rejected due to very limited spatial resolution using existing reactor beams. The second, in vivo prompt gamma neutron activation analysis (IVPGNAA) was much more promising. IVPGNAA was developed using computer simulation and physical measurement coupled with image reconstruction techniques. The method was tested in arthritic New Zealand rabbits previously injected intra-articularly with three boron labeled compounds and shown to be effective in providing information regarding uptake level and residence time of {sup 10}B in the joint.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Lawrence Ives; Eric Montgomery; Zhigang Pan; Blake Riddick; Donald Feldman; Lou Falce

2012-09-25

This program applied reservoir cathode technology to increase the lifetime of cesiated tungsten photocathodes. Cesiated tungsten photocathodes provide a quantum efficiency of approximately 0.08% when cesium is initially applied to the surface. During operation, however, the cesium evaporates from the surface, resulting in a gradual decrease in quantum efficiency. After 4-6 hours of operation, the efficiency drop to below useful levels, requiring recoating on the emission surface. This program developed a cathode geometry where cesium could be continuously diffused to the surface at a rate matching the evaporation rate. This results in constant current emission until the cesium in the reservoir is depleted. Measurements of the evaporation rate indicated that the reservoir should provide cesium for more than 30,000 hours of continuous operation. This is orders of magnitude longer operation then previously available. Experiments also demonstrated that the photocathode could be rejuvenated following contamination from a vacuum leak. Recoating of the emission surface demonstrated that the initial quantum efficiency could be recovered.

Final Technical Report

International Nuclear Information System (INIS)

Diedhiou, Papa Madiallacke

2010-01-01

The established training programme, covering three months is structured over 2 main components: 1. Induced mutagenesis for the genetic improvement of Jatropha; 2. Genotyping using molecular markers in order to link phenotypic diversity to genotype.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Judy D. Wall

2009-02-27

Bioremediation of radionuclides and metals in the subsurface necessitate an understanding of the metabolic capacities and interactions of the anaerobic microorganisms that are found there, including members of the sulfate-reducing bacteria (SRB). Genetic investigation into the pathway of reductant flow to U(VI) in the SRB belonging to the genus Desulfovibrio has been the focus of this project. In Dv. desulfuricans strain G20, we confirmed the importance of the tetraheme cytochrome c3 by disruption of the gene encoding that cytochrome, cycA, and demonstrated a decrease in the ability of the mutant (I2) to reduce U(VI). We found that the cytochrome c3 was necessary for electrons from pyruvate to reach sulfate or fumarate as terminal electron acceptors. It was not needed for electrons from lactate to reach sulfate, from which we infer that a different pathway is used for the electrons from these two substrates. Cyrstal structure of the tetraheme cytochrome c3 was obtained and site-directed mutations of the protein indicated a binding site for metals at heme 4 of the structure. Kinetic studies for oxidation of reduced cytochrome c3 with U(VI) or molybdate revealed a preference for U(VI) as a substrate. Evidence for a role for sodium gradients in the energetic scheme for this soil organism was obtained.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Rasure, John, et. al.

2008-03-07

Through past DOE funding, the MIND Research network has funded a national consortium effort that used multi-modal neuroimaging, genetics, and clinical assessment of subjects to study schizophrenia in both first episode and persistently ill patients. Although active recruitment of research participants is complete, this consortium remains active and productive in terms of analysis of this unique multi-modal data collected on over 320 subjects.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Resasco, Daniel [Univ. of Oklahoma, Norman, OK (United States). School of Chemical, Biological and Materials Engineering; Lobban, Lance [Univ. of Oklahoma, Norman, OK (United States); Crossley, Steven [Univ. of Oklahoma, Norman, OK (United States); Khanna, Vikas [Univ. of Pittsburgh, PA (United States); Maravelias, Christos [Univ. of Wisconsin, Madison, WI (United States); Petkovic, Lucia [Idaho National Lab. (INL), Idaho Falls, ID (United States); Duong, Nhung [Univ. of Oklahoma, Norman, OK (United States)

2018-01-24

The goal was to develop a biomass conversion process that optimizes fractionation and conversion to maximize Carbon efficiency and Hydrogen consumption to obtain drop-in fuels. Selective fractionation of raw biomass was obtained via multi-stage thermal fractionation to produce different streams that are enriched in a particular chemical family (acids, furanics or phenolics). These streams were later catalytically upgraded in both liquid and vapor phase to perform C-C bond formation and hydrodeoxygenation. Among various upgrading strategies investigated we have identified an effective path in which cyclopentanone is a crucial intermediate that can be derived from furfural and other furanics obtained in high concentrations from this thermal staged process. Cyclopentanone is a very versatile molecule, which can couple with itself to product high quality jet-fuel, or couple with phenolic or furanics to create long chain molecules. These (mono-oxygenated) compounds in the correct molecular weight fuel range can be hydrotreated to direct drop-in fuels. Interestingly, we have found that the conversion of furfural to cyclopentanone is not affected by the presence of acetic acid, and, more interestingly, it is enhanced by the presence of water. These are very significant findings, since water and acetic acid are always present in all streams from the primary conversion stage. These results have allowed to complete detailed life-cycle assessment and techno-economic analysis that have been back-fed to the experimentalists to refine the catalyst selection and process operations with the objective of maximizing C efficiency at minimum H utilization. These combined investigations have opened the possibility of an economically and technologically effective process that could result in commercial fuels produced from renewable sources at a cost that might be competitive with fossil fuels.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Li, Lian [West Virginia Univ., Morgantown, WV (United States)

2017-03-08

Our BES supported program integrates molecular beam epitaxy growth with in situ atomic scale imaging using scanning tunneling microscopy/spectroscopy and atomic force microscopy. Aided by density functional theory calculations, we explore enhanced functionalities emerging from the interplay of strain, proximity, and spin-orbit interactions in heterostructures of wide band gap semiconductors, graphene, and Dirac materials, focusing on three thrusts: 1) doping wide bandgap semiconductors and graphene; 2) graphene nanoribbons and graphene-semiconductor heterostructures; and 3) Dirac materials. Our findings and discoveries have led to the publication of one book chapter and twenty-three refereed journal articles, including several in high impact journals such as Nature Communications, Physical Review Letters, and Nano Letters. Highlights of each thrust are provided in the report.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Whitelegge, JP; Faull, KF

2005-06-01

Two primary technologies have been employed for analysis and measurement of the Synechocystis proteome. (1) 2D-gel electrophoresis. Currently one of the most reliable options in quantitative proteomics, typical 2D-gel experiments use isoelectric focusing (IEF) in the first dimension. In the case of membrane proteins, detergents must be added to maintain their solubility though only neutral/zwitterionic surfactants are compatible with the IEF process. We have optimized 2D gel separations for Synechocystis proteins extracted and separated into soluble and membrane subfractions. The resolution and coverage of integral membrane proteins is only marginally satisfactory and alternatives to the first dimension are being considered. Size-exclusion chromatography under non-denaturing conditions was one option that was explored but resolution was insufficient for subfractionation of the membrane-bound proteome. A more highly resolving technique, the ''Blue-native gel'' has proven excellent for Synechocystis and we plan to set up this technology in the near future. Proteins with altered expression are being identified through standard LCMSMS technologies. The analysis of PSI, PSII and SDH deficient mutants is completed, establishing the comparative aspect of the project for integration with the ultrastructural and metabolomic experiments at ASU. We are also looking forward to receiving ftsZ and VIPP1 interruption mutants to explore the effects on the proteome of cell enlargement and disruption of thylakoid biogenesis, respectively. (2) 2D liquid chromatography with mass spectrometry of intact proteins. Early experiments with total membrane protein extracts of Synechocystis showed that the spatial resolution of the reverse-phase separation used in front of the mass spectrometer limited detection to the one hundred or so most abundant proteins. The intact mass tags (IMTs) measured in this experiment represent the first of these measurements that will ultimately define the entire proteome. While some of the IMTs were matched to masses calculated from translations of genomic open-reading frames allowing reasonably confident identification of about half of them (hypothetical IMTs), we are currently validating identifications using a combination of peptide mass fingerprinting after cyanogen bromide cleavage and LC-MSMS after trypsin, of protein in fractions collected during LC-MS+. In order to gain more complete proteome coverage we are applying a liquid separation in front of the LC-MS+ experiment. Size-exclusion chromatography is the first separation technology to be employed, yielding immediate benefits, while still not satisfactory for overall resolution of complexes. Total membranes were solubilized with dodecyl maltoside (1.5%) and separated on deactivated silica (G 4000 SW). LC-MS+ analysis of less-retained chlorophyll-containing fractions, using reverse-phase and size-exclusion technologies, yielded intact protein mass spectra of the two large photosystem I subunits PsaA and PsaB as well as many other IMTs (Figures 1 & 2). These integral membrane proteins have eleven transmembrane helices and, at 81 and 83 kDa, represented one of the most significant challenges to the intact protein molecular weight approach. The identities of the proteins were confirmed by peptide mass fingerprinting and while there is good general agreement between measured and calculated masses it is noted that modest post-translational modifications are necessary to account for the measured molecular weights of the intact proteins. Whether these discrepancies are due to genuine post-translational modifications or DNA sequence errors remains to be determined. The data have been published allowing us to claim to be the first to have completed high-resolution electrospray-ionization mass spectrometry of the core subunits of Photosystem II, Photosystem I and the cytochrome b{sub 6}f complex providing effective proof-of-principle for application of the intact mass approach to the integral membrane proteome. Significantly, we reported greater integral membrane proteome coverage than a colleague studying thylakoids of Arabidopsis illustrating the benefits of the technique over sequential organic extraction of membrane proteins and 1D-gel analysis. The homogeneity of the PsaA and PsaB protein mass spectra attest to the quality of material grown at ASU and the viability of extraction and work up of the material after transport to UCLA.

Final Technical Report

International Development Research Centre (IDRC) Digital Library (Canada)

Tommy Ngai

2014-03-31

Mar 31, 2014 ... framework, based on the Kirkpatrick model (Kirkpatrick, D.L. ..... organizations provide education and training services in water and sanitation. .... Although this resulted in slightly more complicated administrative processes, the new structure ..... water and sanitation supplies in rural sub-Saharan Africa.

Technical Report: Final

Energy Technology Data Exchange (ETDEWEB)

Lueking, Angela D.; Wang, Cheng-Yu

2014-09-30

The objective of this work was to develop catalyzed nanoporous materials that have superior hydrogen uptake between 300K and 400K and moderate pressures. Platinum nanoparticles were introduced to both activated carbons (ACs) and microporous metal organic frameworks (MMOFs) in order to dissociate molecular hydrogen into an active hydrogen species that diffuses from the catalyst to weakly chemisorbs to the AC/MMOF support; this combined sequence is referred to as the hydrogen spillover mechanism. For all materials studied, maximum excess hydrogen uptake was 1-1.4 wt% (excess) at 300K, falling short of DOE storage goals (5.5 wt% by 2015). Select Pt/AC materials (after in situ catalyst activation) had high uptake (up to 1.4 wt%) at low pressure which significantly exceeded that expected for physisorption. The uptake was not correlated to size of Pt catalyst, but appeared to be associated with high surface activity of the AC support and the methodology of catalyst doping. Multiple techniques were explored to introduce Pt nanoparticles into MMOFs, but most led to significant structural degradation. Ultimately, a ‘pre-bridge’ (PB) technique was used to introduce Pt/AC catalysts into MMOFs, as the PB technique led to virtually non-detectable changes in structure. At high pressure, hydrogen spillover of ~1 wt% (excess) to a PB-MMOF was very slow (i.e. >80 hours at 70-80 bar), which can be attributed to high diffusion barriers in a complex three-surface domain material (Pt, AC, MMOF) as well as unexpected evidence for mechanical instability of the undoped MMOF precursor. In a low-pressure comparison study of three PB-MMOFs, we found evidence that the doping technique may introduce defects which may contribute to enhanced adsorption at 300K. However, we could not rule out the effect of active Pt sites, as common predictors of adsorption generally favored the materials without Pt. Furthermore, spectroscopic evidence provided definitive evidence of weak hydrogen chemisorption to two MMOFs and AC, and was found only for materials containing Pt catalyst. Overall, high uptake via hydrogen spillover requires high catalytic activity and an energy neutral surface landscape for ready diffusion, with little to no correlation to the size of the Pt nanoparticle or textural properties (i.e. surface area or porosity) of the AC or MMOF support.

Final technical report

International Nuclear Information System (INIS)

Lin, Chii-Dong

1999-01-01

The goal of this research is to develop new novel methods for studying correlated motion of atomic systems. This involves new formulations of the theoretical approaches, the performance of numerical calculations, and the detailed comparison with available experiment. Different theoretical methods have been developed for different classes of problems. The basis of our theoretical method is the hyperspherical approach. We have studied in general three-body systems and restricted four-body systems, and examined the qualitative properties such as the visualization of the wavefunctions which then allows us to do classifications, and then develop accurate theoretical methods for performing calculations to predict results that can be compared to experiments

FINAL TECHNICAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Fargione, Joseph

2012-02-24

The United States has abundant wind resources, such that only about 3% of the resource would need to be developed to achieve the goal of producing 20% of electricity in the United States by 2030. Inappropriately sited wind development may result in conflicts with wildlife that can delay or derail development projects, increase projects costs, and may degrade important conservation values. The most cost-effective approach to reducing such conflicts is through landscape-scale siting early in project development. To support landscape scale siting that avoids sensitive areas for wildlife, we compiled a database on species distributions, wind resource, disturbed areas, and land ownership. This database can be viewed and obtained via http://wind.tnc.org/awwi. Wind project developers can use this web tool to identify potentially sensitive areas and areas that are already disturbed and are therefore likely to be less sensitive to additional impacts from wind development. The United States goal of producing 20% of its electricity from wind energy by the year 2030 would require 241 GW of terrestrial nameplate capacity. We analyzed whether this goal could be met by using lands that are already disturbed, which would minimize impacts to wildlife. Our research shows that over 14 times the DOE goal could be produced on lands that are already disturbed (primarily cropland and oil and gas fields), after taking into account wind resource availability and areas that would be precluded from wind development because of existing urban development or because of development restrictions. This work was published in the peer reviewed science journal PLoS ONE (a free online journal) and can be viewed here: http://www.plosone.org/article/info%3Adoi%2F10.1371%2Fjournal.pone.0017566. Even projects that are sited appropriately may have some impacts on wildlife habitat that can be offset with offsite compensatory mitigation. We demonstrate one approach to mapping and quantifying mitigation costs, using the state of Kansas as a case study. Our approach considers a range of conservation targets (species and habitat) and calculates mitigation costs based on actual costs of the conservation actions (protection and restoration) that would be needed to fully offset impacts. This work was published in the peer reviewed science journal PLoS ONE (a free online journal) and can be viewed here: http://www.plosone.org/article/info%3Adoi%2F10.1371%2Fjournal.pone.0026698.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Lynn, Douglas C.; Restani, Marco, Ph.D

2009-12-28

The Center of Excellence for Hazardous Materials Management award was used to establish the organization and initiate investigations of hazardous waste issues along the U.S.-Mexico border. Scientific investigations conducted during the execution of this grant contributed significant data and established new sampling protocols to the dimension, frequency and severity of hazardous materials (e.g., heavy metals) along the U.S.-Mexico border. Additionally, new protocols and assessments with distinct Homeland Security implications were embedded thus establishing a baseline that will be significant for related investigations in the future.

Final Technical Report

International Nuclear Information System (INIS)

Dennis L.; Eggleston

2005-01-01

The purpose of this grant was to experimentally investigate asymmetry-induced radial transport in a non-neutral (Penning-Malmberg) plasma trap. These traps provide an excellent platform for transport studies since the plasmas are generally well confined. One can then study transport in a controlled manner: the plasma is perturbed and the resulting transport measured. The focus of this research is the transport produced by applied asymmetric electric fields. The main results of our research concern (1) the theory of asymmetry-induced transport, (2) an absolute comparison of theory predictions with experimental results, (3) the amplitude scaling of the transport, (4) the frequency dependence of the transport, (5) the development of techniques to determine the relative contribution of mobility and diffusion to the transport, and (6) measuring the effect of small axial magnetic variations on the transport

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Magnuson, Timothy S. [Idaho State University

2013-09-10

The biochemistry of bacterial proteins involved in redox transformations of metals and minerals is, without dispute, an important area of research. Nevertheless, most studies on bacterial metal transformation have focused not on biochemistry but on genetics and genomics. The objective of this research is to better understand the role of conformation change in electron transfer from cytochromes to minerals, a process that underpins respiratory metal reduction by bacteria in nature and in bioremediation strategies, including reductive immobilization of radioactive contaminants. Our DOE-funded work is specifically focused on answering long-standing questions about the biochemical behavior of these very interesting proteins, and our findings thus far have already made impacts in the fields of environmental microbiology and biogeochemistry. Among the key findings from the project are 1) Successful large-scale production of biomass for protein isolation; 2) Purification of several c-type cytochromes for biochemical study; 3) Characterization of these proteins using spectrophotometric and electrochemical techniques; 4) Examination of protein conformational change and redox activity towards metal oxides using a small mass cytochrome c from Acidiphilium cryptum; 5) Proteomic characterization of A. cryptum biofilms; 6) Training of 2 undergraduate research assistants; 7) Publications and several meeting presentations.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Finlayson-Pitts, Barbara J.

2014-04-13

DOE has funded our work in three areas: (1) reactions of sea salt aerosols to form photochemically labile halogen gases that help to drive tropospheric chemistry; (2) oxidation of organics at interfaces and formation of SOA driven by oxides of nitrogen photochemistry; and (3) nucleation and growth of new particles in the troposphere from reactions of methanesulfonic acid with amines.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Chen, Cheng-Po [GE Global Research, Niskayuna, New York (United States); Andarawis, Emad [GE Global Research, Niskayuna, New York (United States); Shaddock, David [GE Global Research, Niskayuna, New York (United States); Yin, Liang [GE Global Research, Niskayuna, New York (United States); Ghandi, Reza [GE Global Research, Niskayuna, New York (United States); Srikrishnan, Kashyap [GE Global Research, Niskayuna, New York (United States); Saia, Richard [GE Global Research, Niskayuna, New York (United States); Patil, Amita [GE Global Research, Niskayuna, New York (United States); Fang, Kun [Auburn Univ., AL (United States); Shen, Zhenzhen [Auburn Univ., AL (United States)

2013-09-09

The development and demonstration in this digital telemetry project has brought SiC-based high temperature electronics to a new level of complexity and integration with the active electronic devices and the packaging materials operating at 300°C for greater than 2000 hours. Our highest level of integration is a 6x6mm die with 474 transistors with the most complex functionality to date. Advances were made in the area of device modeling and fabrication, circuit simulation and design, device testing, and packaging. The technologies developed here would help enable sensor systems in enhanced geothermal systems, as well as other applications with high temperature requirements.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

John M. Davis

2005-03-31

The forest products industry consumes large amounts of energy. Understanding how genetic variation in trees actually controls the characteristics of wood, the major raw material utilized by the industry, is an opportunity for energy savings. For companies that are vertically integrated (i.e., have both tree production and processing operations), energy savings can accrue for both production and processing. Tree production demands nitrogen fertilizers, the manufacture of which is highly energy intensive. Wood processing for paper product manufacturing requires digestion and bleaching, both of which are more efficient when the lignin content of wood is reduced. This project identified genes involved in utilization of nitrogen from fertilizer, and the coupling of nitrogen demand to lignin content, establishing a framework for reducing tree nitrogen demand per unit carbon gained. This creates opportunities for genetic manipulation of trees for greater energy efficiency.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Simon Silver

2009-05-28

The work done with DOE support during this 15 year period was extensive and successful. It is best summarized by the list of 58 publications (below) which reported progress made with DOE support. These are from the grant period and a few more recent reporting on grant research. Mostly these are primary research reports in reviewed journals. There are also, however, many summary reviews in review journals and in scientific monographs, as they also are key places for reporting research progress. What we did during this grant period (and much longer) was to characterize genetic determinants for bacterial resistances to additional toxic heavy metals of DOE concern, through starting with phenotypic properties of the resistant bacteria to DNA sequence determination and characterization of the genes involved. Over the years (and as shown in the list of publications), the toxic metal-forming elements we have studied included Ag, As, Cd, Cr, and Hg. In each case, we started with basically nothing (or very little) known, progressed through quite detailed understanding, until other laboratory groups also became strongly involved in related studies. More recently, with DOE support, we were the first laboratory group in the world to identify genes for bacterial resistance to silver salts (sil genes) and the closely related silver-and-copper resistance genes cus. This was initially reported in detail in Gupta et al. (1999; see publications list below). We also identified the first toxic metal 'gene island' (multiple transcripts and perhaps 25 genes each in need of detailed study) which encodes the subunits of arsenite oxidase (which we called aso; Silver and Phung, 2005; but most other researchers have subsequently settled on aox for the gene mnemonic). Both of these systems were firsts. Now a few years later, a search on GenBank shows that each is now represented by gene families with more than a dozen examples that have been identified and sequenced. Most of the additional representative systems are from total bacterial genomes without specific gene characterization.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Sara Bergan, Executive Director; Brendan Jordan, Program Manager; Subcontractors as listed on the report.

2007-06-06

The following report contributes to our knowledge of how to economically produce wildlife-friendly grass mixtures for future fuel feedstocks in the northern plains. It investigates northern-adapted cultivars; management and harvest regimes that are good for yields, soils and wildlife; comparative analysis of monocultures and simple mixtures of native grasses; economic implications of growing grasses for fuel feedstocks in specific locations in the northern plains; and conversion options for turning the grasses into useful chemicals and fuels. The core results of this study suggest the following; Native grasses, even simple grass mixtures, can be produced profitably in the northern plains as far west as the 100th meridian with yields ranging from 2 to 6 tons per acre; Northern adapted cultivars may yield less in good years, but have much greater long-term sustainable yield potential than higher-yielding southern varieties; Grasses require very little inputs and stop economically responding to N applications above 56kg/hectare; Harvesting after a killing frost may reduce the yield available in that given year but will increase overall yields averaged throughout multiple years; Harvesting after a killing frost or even in early spring reduces the level of ash and undesirable molecules like K which cause adverse reactions in pyrolysis processing. Grasses can be managed for biomass harvest and maintain or improve overall soil-health and carbon sequestration benefits of idled grassland; The carbon sequestration activity of the grasses seems to follow the above ground health of the biomass. In other words plots where the above ground biomass is regularly removed can continue to sequester carbon at the rate of 2 tons/acre/year if the stand health is strong and yielding significant amounts of biomass; Managing grasses for feedstock quality in a biomass system requires some of the same management strategies as managing for wildlife benefit. We believe that biomass development can be done in such a way that also maximizes or improves upon conservation and other environmental goals (in some cases even when compared to idled land); Switchgrass and big bluestem work well together in simple mixture plots where big bluestem fills in around the switchgrass which alone grows in bunches and leaves patches of bare soil open and susceptible to erosion; Longer-term studies in the northern plains may also find that every other year harvest schemes produce as much biomass averaged over the years as annual harvests; Grasses can be grown for between $23 and $54/ton in the northern plains at production rates between 3 and 5 tons/acre; Land costs, yields, and harvest frequency are the largest determining factors in the farm scale economics. Without any land rent offset or incentive for production, and with annual harvesting, grass production is likely to be around $35/ton in the northern plains (farm gate); Average transportation costs range from $3 to $10/ton delivered to the plant gate. Average distance from the plant is the biggest factor - $3/ton at 10 miles, $10/ton at 50 miles; There is a substantial penalty paid on a per unit of energy produced basis when one converts grasses to bio-oil, but the bio-oil can then compete in higher priced fuel markets whereas grasses alone compete directly with relatively cheap coal; Bio oil or modified bio-oil (without the HA or other chemical fraction) is a suitable fuel for boiler and combustion turbines that would otherwise use residual fuel oil or number 2 diesel; Ensyn has already commercialized the use of HA in smokey flavorants for the food industry but that market is rather small. HA, however, is also found to be a suitable replacement for the much larger US market for ethanolamines and ethalyne oxides that are used as dispersants; Unless crude oil prices rise, the highest and best use of grass based bio-oil is primarily as a direct fuel. As prices rise, HA, phenol and other chemical fractions may become more attractive; Although we were able to create available glucose from the AHG fraction in the bio-oil it proved recalcitrant to fermentation by yeast. Although fermentation results were much more positive with wood based bio-oil sugars, ethanol does not appear to be a likely product from grass based bio-oil; and A package of policy recommendations has been developed with roughly 75 key stakeholders from throughout the region that would support the transition to greater development of advanced biofuels and products in the region, as well as a strong role for native grass agriculture to support those industries.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

de Szoeke, Simon P. [Oregon State Univ., Corvallis, OR (United States)

2018-03-02

The investigator and DOE-supported student [1] retrieved vertical air velocity and microphysical fall velocity retrieval for VOCALS and CAP-MBL homogeneous clouds. [2] Calculated in-cloud and cloud top dissipation calculation and diurnal cycle computed for VOCALS. [3] Compared CAP-MBL Doppler cloud radar scenes with (Remillard et al. 2012) automated classification.

FINAL TECHNICAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Loren F. Goodrich

2011-05-31

NIST has played a key role in many of the one-on-one, domestic, and international interlaboratory comparisons of measurements on superconductors. The history of interlaboratory comparisons of measurements on superconductors tells us that careful measurement methods are needed to obtain consistent results. Inconsistent results can lead to many problems including: a mistrust of the results of others, unfair advantages in commerce, and erroneous feedback in the optimization of conductor performance. NIST has experience in many interlaboratory comparisons; a long-term commitment to measurement accuracy; and independent, third-party laboratory status. The principal investigator's direct involvement in the measurements and daily supervision of sample mounting is the unique situation that has allowed important discoveries and evolution of our capabilities over the last 30 years. The principal investigator's research and metrology has helped to improve the accuracy of critical-current (I{sub c}) measurements in laboratories throughout the world. As conductors continue to improve and design limits are tested, the continuation of the long-term commitment to measurement accuracy could be vitally important to the success of new conductor development programs. It is extremely important to the U.S. wire manufacturers to get accurate (high certainty) I{sub c} measurements in order to optimize conductor performance. The optimization requires the adjustment of several fabrication parameters (such as reaction time, reaction temperature, conductor design, doping, diffusion barrier, Cu to non-Cu ratio, and twist pitch) based on the I{sub c} measurement of the conductor. If the I{sub c} measurements are made with high variability, it may be unclear whether or not the parameters are being adjusted in the optimal direction or whether or not the conductor meets the target specification. Our metrology is vital to the U.S. wire manufacturers in the highly competitive international arena and to meet the aggressive performance goals. The latest high-performance Nb{sub 3}Sn wires are being designed with higher current densities, larger effective filament diameter, less Cu stabilizer, and, in some cases, larger wire diameters than ever before. In addition, some of the conductor designs and heat treatments cause the residual resistivity ratio (RRR, ratio of room temperature resistivity to the resistivity at 20 K) of the stabilizer to be less than 20. These parameters are pushing the conductors towards less intrinsic stability, into a region we call marginally stable. These parameters also create a whole series of challenges for routine I{sub c} testing on short-samples, even when tested with the sample immersed in liquid helium. High-current, variable-temperature I{sub c} measurements are even more difficult than those made in liquid helium because the sample is only cooled by flowing helium gas. Providing accurate I{sub c} results under these conditions requires a complex system that provide adequate cooling as well as uniform sample temperature. We have been make variable-temperature measurements for about 15 years, but we started to design the first high-current (at least 500 A), variable-temperature, variable-strain apparatus in late 2006. Our first critical-current measurements as a function of strain, temperature, and magnetic field, I{sub c}(B,T,{var_epsilon}), in a new single, unified apparatus (full matrix characterization) were made in the summer of 2008. This is the only such facility in the U.S. and it has some unique components that are not duplicated anywhere in the world. The compounding of all three variables (H, T, {var_epsilon}) makes an already labor and time intensive characterization very formidable; however, the results cannot be generated any other way and are needed to answer key questions about strain and temperature safety margins and about the reliability of using scaling laws based on small data sets to predict performance. In the future, this new apparatus will allow NIST to create a database on strands that would benefit U.S. superconductor wire manufacturers, national research laboratories, and programs using superconductor strands such as HEP and International Thermonuclear Experimental Reactor (ITER).

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Thiel, Jerry; Giese, Scott R; Beckermann, Christoph; Combi, Joan; Yavorsky, James; Cannon, Fred

2009-09-30

The Center for Advanced Biobased was created with funding supplied by the Department of Energy to study biobased alternatives to petroleum based materials used in the manufacture of foundry sand binders. The project was successful in developing two new biobased polymers that are based on renewable agricultural materials or abundant naturally occurring organic materials. The technology has the potential of replacing large amounts of chemicals produced from oil with environmentally friendly alternatives.

Final technical report

Energy Technology Data Exchange (ETDEWEB)

Loveland, Walter David [Oregon State Univ., Corvallis, OR (United States)

2016-08-27

This report describes the research carried out under this grant for the period from 1997 to 2014. This work has been previously described in annual progress reports and renewal applications. As a result of this project, ~100 papers were published in open refereed journals and 107 invited talks were given by the PI. The research subjects covered by this project included the synthesis and characterization of super-heavy nuclei, the critical study of the reaction mechanisms used in these synthesis reactions, the mechanism(s) of intermediate energy and relativistic nuclear collisions, the study of reactions induced by radioactive nuclear beams, and general properties of the heaviest elements.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Spivey, James J. [Louisiana State Univ., Baton Rouge, LA (United States)

2016-02-02

The research summarized here has the goal of developing a fundamental understanding of how catalysts work. These materials are demonstrably essential to our daily life, from the cars we drive to the clothes we wear. Our Center advances the science behind how we prepare, analyze, and describe catalysts. This has been identified by one of the documents guiding Federal research objectives (Directing Matter and Energy: Five Challenges for Science and the Imagination): “Major challenges in heterogeneous catalysis are to more clearly define the nature of the active sites, to engineer at the molecular level catalysis with designed properties in three dimensions, and to create new catalysts for new transformations.” This directly addresses this objective.

Final technical report

Energy Technology Data Exchange (ETDEWEB)

Johnson, C.; Long, S.; Li, Binsheng; Lamke, A.J.

1994-07-01

The overall goal of the contract is to provide general support and advice to the DOE, Office of Fossil Energy (DOE/EF) on the opportunities for coal and Clean Coal Technology trade in the Asia-Pacific region. The report which follows is divided into six subsections, each pertaining to separate subtasks the U.S. Department of Energy requested. Subtask A includes two reports, one which outlines important coal and clean coal technology news events which occurred during the second half of 1993, and another which outlines the potential for Clean Coal Technology in the Asia-Pacific Region. Subtask B and the first paper in Subtask C contain advisories and briefing papers that present and explain the coal, electricity and Clean Coal Technology situation in China. The second paper in Subtask C is an overview of the coal supply, demand and trade situation in the Asian region with coal projections to the year 2010. Subtask D is an overview of meetings with Asian energy and policy representatives which were carried out to (1) gather key information relevant to this contract, and (2) examine areas for closer cooperation on important coal/CCT-related energy issues. The tasks listed in the contract proposal as Subtasks E and F are summarized in respective sections of this report. Subtask E specifies the activities carried out under the APEC Experts` Group on Clean Coal Technologies, and Subtask F explains the work done by the Coal Project in building contacts and working relationships with key energy and technology planners in China (including The State Science and Technology Commission, the Ministry of Electric Power and Tsinghua University, and the State Planning Commission). The Subtask E section also includes activities to develop and strengthen the role of the APEC Experts Group on Clean Coal Activities.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jack Brenizer

2011-05-16

The Consortium of Big-10 University Research and Training Reactors was by design a strategic partnership of seven leading institutions. We received the support of both our industry and DOE laboratory partners. Investiments in reactor, laboratory and program infrastructure, allowed us to lead the national effort to expand and improve the education of engineers in nuclear science and engineering, to provide outreach and education to pre-college educators and students and to become a key resource of ideas and trained personnel for our U.S. industrial and DOE laboratory collaborators.

Whole genome amplification in preimplantation genetic diagnosis*

Science.gov (United States)

Zheng, Ying-ming; Wang, Ning; Li, Lei; Jin, Fan

2011-01-01

Preimplantation genetic diagnosis (PGD) refers to a procedure for genetically analyzing embryos prior to implantation, improving the chance of conception for patients at high risk of transmitting specific inherited disorders. This method has been widely used for a large number of genetic disorders since the first successful application in the early 1990s. Polymerase chain reaction (PCR) and fluorescent in situ hybridization (FISH) are the two main methods in PGD, but there are some inevitable shortcomings limiting the scope of genetic diagnosis. Fortunately, different whole genome amplification (WGA) techniques have been developed to overcome these problems. Sufficient DNA can be amplified and multiple tasks which need abundant DNA can be performed. Moreover, WGA products can be analyzed as a template for multi-loci and multi-gene during the subsequent DNA analysis. In this review, we will focus on the currently available WGA techniques and their applications, as well as the new technical trends from WGA products. PMID:21194180

Technical procedures for ecology: Environmental field program, Deaf Smith County Site, Texas: Final draft

International Nuclear Information System (INIS)

1987-08-01

This volume contains Technical Procedures pursuant to the Land Use Site Study Plan including walkover surveys for threatened, endangered, or candidate species; vegetation classification and mapping; reclamation planning; wetland and floodplain determination and characterization of playas; wildlife habitat mapping methods; mammal sampling; bird survey methods; reptile and amphibian survey methods; preexisting environmental; stress and disturbance studies methods; voucher specimens for plants; and voucher specimens to wildlife. 9 refs., 5 figs., 1 tab

Endogenous induced technical change and the costs of Kyoto

International Nuclear Information System (INIS)

Buonanno, Paolo; Carraro, Carlo; Galeotti, M.

2001-09-01

Many predictions and conclusions in the climate change literature have been made and drawn on the basis of theoretical analyses and quantitative models that are either static or that allow for simple forms of changes in technology, often along exogenously given time paths. It is therefore not clear a priori whether those conclusions and policy recipes still hold in the more realistic case of endogenously evolving technologies. In this paper, a quantitative tool with the features of an endogenous growth model is presented, which also accounts for the possibility that technical change can be induced by environmental policy measures. Both the output production technology and the emission-output ratio depend upon the stock of knowledge, which accumulates through R and D activities. R and D is thus an additional policy variable that comes into play along with pollution abatement and capital investment. Two versions of this climate model are studied, one with endogenous technical change but exogenous environmental technical change (i.e. no induced technical change) and the other with both endogenous and induced technical change. Hence, in both models technical change evolves endogenously as far as the production technology is concerned, but endogenous environmental (or induced) technical change is only accounted for in the second version. Finally, a third version of the model also captures technological spillover effects. As an application, the three versions of the model are simulated allowing for trade of pollution permits as specified in the Kyoto Protocol and assessing the implications in terms of cost efficiency, economic growth and R and D efforts of the three different specifications of technical change

Role of diagnostic laparoscopy in chronic abdominal conditions with uncertain diagnosis

Directory of Open Access Journals (Sweden)

Amandeep S Nar

2014-01-01

Full Text Available Introduction: Laparoscopy has proved to be an important tool in the minimally invasive exploration of selected patients with chronic abdominal disorders, whose diagnosis remains uncertain, despite exploring the requisite laboratory and imaging investigations like ultrasonography, computed tomography (CT scan, and the like. Materials and Methods: Diagnostic Laparoscopy was conducted on 120 patients, admitted to the Departments of Surgery and Gynecology, Dayanand Medical College and Hospital, Ludhiana, with an uncertain diagnosis after four weeks of onset of symptoms. Conclusion: With laparoscopy providing tissue diagnosis, and helping to achieve the final diagnosis without any significant complication and less operative time, it can be safely concluded that diagnostic laparoscopy is a safe, quick, and effective adjunct to non-surgical diagnostic modalities, for establishing a conclusive diagnosis, but whether it will replace imaging studies as a primary modality for diagnosis needs more evidence.

Final Project Report Project 10749-4.2.2.1 2007-2009

Energy Technology Data Exchange (ETDEWEB)

Zacher, Alan H.; Holladay, Johnathan E.; Frye, J. G.; Brown, Heather M.; Santosa, Daniel M.; Oberg, Aaron A.

2009-05-11

This is the final report for the DOE Project 10749-4.2.2.1 for the FY2007 - FY2009 period. This report is non-proprietary, and will be submitted to DOE as a final project report. The report covers activities under the DOE Project inside CRADA 269 (Project 53231) as well as project activites outside of that CRADA (Project 56662). This is the final report that is summarized from the non-proprietary quarterlies submitted to DOE over the past 2.5 years, which in turn are summaries from the proprietary technical reporting to UOP.

Final radioactive waste disposal: A European comparison of organization and costs

International Nuclear Information System (INIS)

Drasdo, P.

2000-01-01

The investigation is aimed to the comparison of organization structures of operators (plants) and governmental institutions concerned with the final disposal of radioactive waste. The study is covering Germany, France, United Kingdom and Sweden. The capital amount of total final disposal costs are the highest in Germany, the lowest in Sweden. This is also true for the final disposal costs that have to be financed by electricity production from nuclear power plants. The reasons for the differences with respect to economic efficiencies, political decisions and technical concepts are discussed

Preclinical diagnosis and emergency medical care in case of radiation accidents

International Nuclear Information System (INIS)

Ohlenschlaeger, L.

1990-01-01

Reference is made to preclinical diagnosis and emergency medical care at the site of a potential radiation accident. Possibilities and limits, respectively, of the medical measures are shown. Cooperation between the experts of the technical and medical rescue services is described. Exposition to radiation for the emergency medical staff resulting from the medical care of contaminated persons, is negligible if the personal precautions are observed. (orig.) [de

Value of ultrasonography in the differential diagnosis of appendicitis

International Nuclear Information System (INIS)

Alonso, J.M.; Sandoval, E.

1998-01-01

To determine the utility of ultrasound in the diagnosis of diseases that can be confused with appendicitis or presenting with atypical clinical signs of appendiceal inflammation. Graded-compression ultrasound was performed in 226 patients presenting with pain in right iliac fossa. Twenty-three patients were excluded because of inconclusive examination. Appendicitis was confirmed intraoperatively in 98 cases. There was no appendiceal inflammation in 105 patients. A final diagnosis could not be reached in 26 cases (4.7%) and was considered to represent abdominal pain of unknown origin. Ultrasound provided the correct diagnosis in 72 of the 79 patients in whom a definitive diagnosis was reached (91.1%). A wide spectrum of pathologies was identified by ultrasound, including gastrointestinal complaints (n=51), gynecological disorders (n=10), bioliopancreatic abnormalities (n=4), urological diseases (n=3) and others (n=3). Ultrasound is useful in the differential diagnosis of patients with confusing clinical signs of appendicitis. (Author) 34 refs

INDOT Technical Training Plan : [Technical Summary

Science.gov (United States)

2012-01-01

A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

A NEW TEACHING METHOD OF TECHNICAL DRAWING

Directory of Open Access Journals (Sweden)

TOMA Ana-Maria

2017-05-01

Full Text Available The paper represents a project of applied research, on how to teach more effectively the subject of technical drawing, using Student - centred education methods. The authors applied a new method of interaction with the students and teaching during a semester and the conclusions were drawn comparing the final results of the classes on which this project was applied with the ones where the classical method of teaching was applied.

IPEN Scientific and technical publications 1956-1981

International Nuclear Information System (INIS)

1983-01-01

The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/SP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this jubilee edition include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. This present volume, published under the new title of IPEN - Scientific and Technical Publications, is a cumulative edition, to celebrate the 25th. anniversary of IPEN. In this jubilee edition, 1345 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

Data-driven design of fault diagnosis and fault-tolerant control systems

CERN Document Server

Ding, Steven X

2014-01-01

Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems presents basic statistical process monitoring, fault diagnosis, and control methods, and introduces advanced data-driven schemes for the design of fault diagnosis and fault-tolerant control systems catering to the needs of dynamic industrial processes. With ever increasing demands for reliability, availability and safety in technical processes and assets, process monitoring and fault-tolerance have become important issues surrounding the design of automatic control systems. This text shows the reader how, thanks to the rapid development of information technology, key techniques of data-driven and statistical process monitoring and control can now become widely used in industrial practice to address these issues. To allow for self-contained study and facilitate implementation in real applications, important mathematical and control theoretical knowledge and tools are included in this book. Major schemes are presented in algorithm form and...

Parkinsonian syndroms: Clinical phenotype, differential diagnosis and disease progression

International Nuclear Information System (INIS)

Storch, A.

2002-01-01

Parkinsonian syndromes include idiopathic Parkinson's disease (IPD), other neurodegenerative diseases with parkinsonism, the so-called atypical parkinsonian syndromes, and symptomatic parkinsonian syndromes, such as Wilson's disease. IPD is the most frequent disease with parkinsonism as the main clinical feature and is responsible for approx. 80% of all parkinsonian syndromes. Atypical parkinsonian syndromes are the most important differential diagnoses of IPD. The two most frequent types are multiple system atrophy (MSA) and progressive supranuclear palsy (PSP). For clinical diagnosis it is essential to take a careful medical history and to examine the patients physically in regular intervals. However, various clinico-pathological studies have shown that approx. 25% of patients with clinical diagnosis of IPD may have other causes of parkinsonism. Selected technical investigations, in particular functional imaging of the central dopaminergic system using PET or SPECT, may help to make clinical diagnosis more secure. This paper reviews the clinical features and diagnostic findings in diseases with parkinsonism and summarises the difficulties in establishing early and differential diagnoses. (orig.) [de

Diagnosis delay in Libyan female breast cancer

Directory of Open Access Journals (Sweden)

Ermiah Eramah

2012-08-01

Full Text Available Abstract Aims To study the diagnosis delay and its impact on stage of disease among women with breast cancer on Libya. Methods 200 women, aged 22 to 75 years with breast cancer diagnosed during 2008–2009 were interviewed about the period from the first symptoms to the final histological diagnosis of breast cancer. This period (diagnosis time was categorized into 3 periods: 6 months. If diagnosis time was longer than 3 months, the diagnosis was considered delayed (diagnosis delay. Consultation time was the time taken to visit the general practitioner after the first symptoms. Retrospective preclinical and clinical data were collected on a form (questionnaire during an interview with each patient and from medical records. Results The median of diagnosis time was 7.5 months. Only 30.0% of patients were diagnosed within 3 months after symptoms. 14% of patients were diagnosed within 3–6 months and 56% within a period longer than 6 months. A number of factors predicted diagnosis delay: Symptoms were not considered serious in 27% of patients. Alternative therapy (therapy not associated with cancer was applied in 13.0% of the patients. Fear and shame prevented the visit to the doctor in 10% and 4.5% of patients, respectively. Inappropriate reassurance that the lump was benign was an important reason for prolongation of the diagnosis time. Diagnosis delay was associated with initial breast symptom(s that did not include a lump (p  Diagnosis delay was associated with bigger tumour size (p Conclusions Diagnosis delay is very serious problem in Libya. Diagnosis delay was associated with complex interactions between several factors and with advanced stages. There is a need for improving breast cancer awareness and training of general practitioners to reduce breast cancer mortality by promoting early detection. The treatment guidelines should pay more attention to the early phases of breast cancer. Especially, guidelines for good practices in managing

Computer modeling of lung cancer diagnosis-to-treatment process.

Science.gov (United States)

Ju, Feng; Lee, Hyo Kyung; Osarogiagbon, Raymond U; Yu, Xinhua; Faris, Nick; Li, Jingshan

2015-08-01

We introduce an example of a rigorous, quantitative method for quality improvement in lung cancer care-delivery. Computer process modeling methods are introduced for lung cancer diagnosis, staging and treatment selection process. Two types of process modeling techniques, discrete event simulation (DES) and analytical models, are briefly reviewed. Recent developments in DES are outlined and the necessary data and procedures to develop a DES model for lung cancer diagnosis, leading up to surgical treatment process are summarized. The analytical models include both Markov chain model and closed formulas. The Markov chain models with its application in healthcare are introduced and the approach to derive a lung cancer diagnosis process model is presented. Similarly, the procedure to derive closed formulas evaluating the diagnosis process performance is outlined. Finally, the pros and cons of these methods are discussed.

Final technical report on studies of plasma transport

International Nuclear Information System (INIS)

O'Neil, T.M.; Driscoll, C.F.; Malmberg, J.H.

1997-01-01

This document gives an overview of the scientific results obtained under the DOE grant, and references the journal articles which give more complete descriptions of the various topics. Recently, the research has been focused on 2-dimensional vortices and turbulence: experiments using a new camera-diagnosed electron plasma apparatus have given surprising results which both clarify and challenge theories. Here, the crossfield E x B flow of the electron plasma is directly analogous to the 2-d flow of an ideal fluid such as water, and may also give insight into more complicated poloidal flows exhibited in toroidal plasmas. The shear-flow instabilities, turbulence, and vortices can be accurately observed, and the free relaxation of this turbulence has been characterized. The physical processes underlying the complicated turbulent evolution can also be studied in more controlled near-linear regimes. The original experimental focus of this program was on radial particle transport from applied external field asymmetries. Here, this research program clearly identified the importance of the collective response of the plasma, giving smaller fields from shielding, or enhanced fields from resonant modes. Experiments and theory work have also elucidated the flow of a plasma along the magnetic field. Finally, some theory was pursued for direct application to fusion plasmas, and to gravitating gas clouds in astrophysics. This program was highly successful in clarifying basic plasma transport processes

Support vector machine in machine condition monitoring and fault diagnosis

Science.gov (United States)

Widodo, Achmad; Yang, Bo-Suk

2007-08-01

Recently, the issue of machine condition monitoring and fault diagnosis as a part of maintenance system became global due to the potential advantages to be gained from reduced maintenance costs, improved productivity and increased machine availability. This paper presents a survey of machine condition monitoring and fault diagnosis using support vector machine (SVM). It attempts to summarize and review the recent research and developments of SVM in machine condition monitoring and diagnosis. Numerous methods have been developed based on intelligent systems such as artificial neural network, fuzzy expert system, condition-based reasoning, random forest, etc. However, the use of SVM for machine condition monitoring and fault diagnosis is still rare. SVM has excellent performance in generalization so it can produce high accuracy in classification for machine condition monitoring and diagnosis. Until 2006, the use of SVM in machine condition monitoring and fault diagnosis is tending to develop towards expertise orientation and problem-oriented domain. Finally, the ability to continually change and obtain a novel idea for machine condition monitoring and fault diagnosis using SVM will be future works.

Differential diagnosis of Jakob-Creutzfeldt disease.

Science.gov (United States)

Paterson, Ross W; Torres-Chae, Charles C; Kuo, Amy L; Ando, Tim; Nguyen, Elizabeth A; Wong, Katherine; DeArmond, Stephen J; Haman, Aissa; Garcia, Paul; Johnson, David Y; Miller, Bruce L; Geschwind, Michael D

2012-12-01

To identify the misdiagnoses of patients with sporadic Jakob-Creutzfeldt disease (sCJD) during the course of their disease and determine which medical specialties saw patients with sCJD prior to the correct diagnosis being made and at what point in the disease course a correct diagnosis was made. Retrospective medical record review. A specialty referral center of a tertiary academic medical center. One hundred sixty-three serial patients over a 5.5-year period who ultimately had pathologically proven sCJD. The study used the subset of 97 patients for whom we had adequate medical records. Other diagnoses considered in the differential diagnosis and types of medical specialties assessing patients with sCJD. Ninety-seven subjects' records were used in the final analysis. The most common disease categories of misdiagnosis were neurodegenerative, autoimmune/paraneoplastic, infectious, and toxic/metabolic disorders. The most common individual misdiagnoses were viral encephalitis, paraneoplastic disorder, depression, vertigo, Alzheimer disease, stroke, unspecified dementia, central nervous system vasculitis, peripheral neuropathy, and Hashimoto encephalopathy. The physicians who most commonly made these misdiagnoses were primary care physicians and neurologists; in the 18% of patients who were diagnosed correctly at their first assessment, the diagnosis was almost always by a neurologist. The mean time from onset to diagnosis was 7.9 months, an average of two-thirds of the way through their disease course. Diagnosis of sCJD is quite delayed. When evaluating patients with rapidly progressive dementia with suspected neurodegenerative, autoimmune, infectious, or toxic/metabolic etiology, sCJD should also be included in the differential diagnosis, and appropriate diagnostic tests, such as diffusion brain magnetic resonance imaging, should be considered. Primary care physicians and neurologists need improved training in sCJD diagnosis.

Image processing for medical diagnosis of human organs

International Nuclear Information System (INIS)

Tamura, Shin-ichi

1989-01-01

The report first describes expectations and needs for diagnostic imaging in the field of clinical medicine, radiation medicine in particular, viewed by the author as an image processing expert working at a medical institute. Then, medical image processing techniques are discussed in relation to advanced information processing techniques that are currently drawing much attention in the field of engineering. Finally, discussion is also made of practical applications of image processing techniques to diagnosis. In the field of clinical diagnosis, advanced equipment such as PACS (picture archiving and communication system) has come into wider use, and efforts have been made to shift from visual examination to more quantitative and objective diagnosis by means of such advanced systems. In clinical medicine, practical, robust systems are more useful than sophisticated ones. It is difficult, though important, to develop completely automatized diagnostic systems. The urgent, realistic goal, therefore, is to develop effective diagnosis support systems. In particular, operation support systems equipped with three-dimensional displays will be very useful. (N.K.)

Early diagnosis of autism spectrum disorder: stability and change in clinical diagnosis and symptom presentation.

Science.gov (United States)

Guthrie, Whitney; Swineford, Lauren B; Nottke, Charly; Wetherby, Amy M

2013-05-01

Although a diagnosis of autism spectrum disorder (ASD) appears to be stable in children as young as age three, few studies have explored stability of a diagnosis in younger children. Predictive value of diagnostic tools for toddlers and patterns of symptom change are important considerations for clinicians making early diagnoses. Most findings come from high-risk samples, but reports on children screened in community settings are also needed. Stability of diagnosis and Autism Diagnostic Observation Schedule – Toddler Module (ADOS-T) classifications and scores was examined across two time points in a sample of 82 children identified through the FIRST WORDS Project.Children received two comprehensive diagnostic evaluations at average ages of 19.39 (SD = 2.12) and 36.89 (SD = 3.85) months. Stability was 100% when confirming and ruling out a diagnosis of ASD based on a comprehensive diagnostic evaluation that included clinic and home observations,although diagnosis was initially deferred for 17% of the sample. Receiver Operating Characteristic curves revealed excellent sensitivity and acceptable specificity for the ADOS-T compared to concurrent diagnosis. Logistic regressions indicated good predictive value of initial ADOS-T scores for follow-up diagnosis. Finally, both ASD and Non-ASD children demonstrated a decrease in Social Affect scores (i.e.,improvement), whereas children with ASD demonstrated an increase in Restricted and Repetitive Behavior scores (i.e., worsening), changes that were accounted for by nonverbal developmental level in mixed model analyses. Short-term stability was documented for children diagnosed at 19 months on average, although a minority of children initially showed unclear diagnostic presentations.Findings highlight utility of the ADOS-T in making early diagnoses and predicting follow-up diagnoses. Children with ASD demonstrated improvement in social communication behaviors and unfolding of repetitive behaviors, suggesting that certain

Final Technical Report Steam Cycle Washer for Unbleached Pulp

Energy Technology Data Exchange (ETDEWEB)

Starkey, Yvonne; Salminen, Reijo; Karlsnes, Andy

2008-09-22

Project Abstract for “Steam Cycle Washer for Unbleached Pulp” When completed, the patented SC Washer will provide an innovative, energy efficient demonstration project to wash unbleached pulp using a pressure vessel charged with steam. The Port Townsend Paper Corporation’s pulp mill in Port Townsend, WA was initially selected as the host site for conducting the demonstration of the SCW. Due to 2006 and 2007 delays in the project caused by issues with 21st Century Pulp & Paper, the developer of the SCW, and the 2007 bankruptcy proceedings and subsequent restructuring at Port Townsend Paper, the mill can no longer serve as a host site. An alternate host site is now being sought to complete the commercial demonstration of the Steam Cycle Washer for Unbleached Pulp. Additionally, estimated costs to complete the project have more than doubled since the initial estimates for the project were completed in 2002. Additional grant funding from DOE was sought and in July, 2008 the additional DOE funds were procured under a new DOE award, DE-PS36-08GO98014 issued to INL. Once the new host site is secured the completion of the project will begin under the management of INL. Future progress reports and milestone tracking will be completed under requirements of new DOE Award Number DE-PS36-08GO98014. The following are excerpts from the project Peer Review completed in 2006. They describe the project in some detail. Additional information can be found by reviewing DOE Award Number: DE-PS36-08GO98014. 5. Statement of Problem and Technical Barriers: The chemical pulping industry is one of the major users of fresh water in the United States. On average the industry uses over 80 tons of water to produce one ton of pulp, some states use up to 50% more (Washington 120 and Wisconsin 140). In order to process one ton of pulp using 80 tons of process water, a large amount of: • energy is used in process heat and • power is required for pumping the large volume of pulp slurries

Uranium Mill Tailings Remedial Action Project: technical approach document

International Nuclear Information System (INIS)

1986-05-01

The Uranium Mill Tailings Radiation Control Act of 1978, PL95-604, grants the Secretary of Energy authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards from inactive uranium mill sites. These cleanup actions are to be performed in compliance with the EPA standards (40 CFR Part 192) which became final on March 7, 1983. This document describes the general technical approaches and design criteria that are adopted by the US Department of Energy (DOE) in order to implement Remedial Action Plans (RAPs) and final designs that comply with EPA standards

Determining the analytical specificity of PCR-based assays for the diagnosis of IA: What is Aspergillus?

NARCIS (Netherlands)

Morton, C.O.; White, P.L.; Barnes, R.A.; Klingspor, L.; Cuenca-Estrella, M.; Lagrou, K.; Bretagne, S.; Melchers, W.J.; Mengoli, C.; Caliendo, A.M.; Cogliati, M.; Debets-Ossenkopp, Y.; Gorton, R.; Hagen, F.; Halliday, C.; Hamal, P.; Harvey-Wood, K.; Jaton, K.; Johnson, G.; Kidd, S.; Lengerova, M.; Lass-Florl, C.; Linton, C.; Millon, L.; Morrissey, C.O.; Paholcsek, M.; Talento, A.F.; Ruhnke, M.; Willinger, B.; Donnelly, J.P.; Loeffler, J.

2017-01-01

A wide array of PCR tests has been developed to aid the diagnosis of invasive aspergillosis (IA), providing technical diversity but limiting standardisation and acceptance. Methodological recommendations for testing blood samples using PCR exist, based on achieving optimal assay sensitivity to help

Noninvasive prenatal diagnosis for single gene disorders.

Science.gov (United States)

Allen, Stephanie; Young, Elizabeth; Bowns, Benjamin

2017-04-01

Noninvasive prenatal diagnosis for single gene disorders is coming to fruition in its clinical utility. The presence of cell-free DNA in maternal plasma has been recognized for many years, and a number of applications have developed from this. Noninvasive prenatal diagnosis for single gene disorders has lagged behind due to complexities of technology development, lack of investment and the need for validation samples for rare disorders. Publications are emerging demonstrating a variety of technical approaches and feasibility of clinical application. Techniques for analysis of cell-free DNA including digital PCR, next-generation sequencing and relative haplotype dosage have been used most often for assay development. Analysis of circulating fetal cells in the maternal blood is still being investigated as a viable alternative and more recently transcervical trophoblast cells. Studies exploring ethical and social issues are generally positive but raise concerns around the routinization of prenatal testing. Further work is necessary to make testing available to all patients with a pregnancy at risk of a single gene disorder, and it remains to be seen if the development of more powerful technologies such as isolation and analysis of single cells will shift the emphasis of noninvasive prenatal diagnosis. As testing becomes possible for a wider range of conditions, more ethical questions will become relevant.

Radiological Effluent Technical Specifications (RETS) implementation: Zion Generating Station Units 1 and 2

International Nuclear Information System (INIS)

Serrano, W.; Akers, D.W.; Duce, S.W.; Mandler, J.W.; Simpson, F.B.; Young, T.E.

1985-06-01

A review of the Radiological Effluent Technical Specifications (RETS) of the Zion Generating Station Units 1 and 2 was performed. The principal review guidelines used were NUREG-0133, ''Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants,'' and Draft 7 of NUREG-0472, Revision 3, ''Radiological Effluent Technical Specifications for Pressurized Water Reactors.'' Draft submittals were discussed with the Licensee by both EG and G and the NRC staff until all items requiring changes to the Technical Specifications were resolved. The Licensee then submitted final proposed RETS to the NRC which were evaluated and found to be in compliance with the NRC review guidelines. The proposed Offsite Dose Calculation Manual was reviewed and generally found to be consistent with the NRC review guidelines. 35 refs., 2 figs., 1 tab

Verification of medical diagnosis establishments with X radiation; Verificacion de establecimientos de diagnostico medico con rayos X

Energy Technology Data Exchange (ETDEWEB)

Azorin N, J. [Lider Nacional de Proteccion Radiologica, Comision Federal para la Proteccion contra Riesgos Sanitarios, Monterrey No. 33, Col. Roma, 06700 Mexico D. F. (Mexico)

2008-12-15

In regard to verification of medical diagnosis establishments with X radiation, it is very important to the coordination between the competent authorities such as the coordination achieved between the Federal Commission for the Protection against Sanitary Risks attached to the Health Secretary and the National Commission of Nuclear Safety and Safeguards, under the Energy Secretary. The Health Secretary found a subcommittee of environmental health standards to develop the Mexican Official Standards of medical diagnosis with X-rays, with the participation of over 50 institutions and experts in Mexico. The legal framework governing the procedures for health surveillance in radiology include the Health General Law, the Internal Regulation of the Health Secretary, the Regulation of the Federal Commission for the Protection against Sanitary Risks and the Mexican Official Standard NOM-229 SSA1 -2002, {sup T}echnical requirements for the facilities, health responsibilities, technical specifications for the equipment and radiation protection in medical diagnosis establishments with X-rays{sup .} Among the participated institutions in the revision of this standard were federal government agencies, public and private sector institutions, educational institutions and professional associations. The standard establishes criteria for design, construction and facilities maintenance, technical requirements for the acquisition and operation vigilance of equipment, health requirements and patient protection. Standard observance is for establishments that use X-ray generators for its application in humans with purposes of medical diagnosis either fixed or mobile units. It also contains aspects that must be observed by owners of establishments who hold formal, responsible, own X-ray equipment and consultants with expertise in radiation protection. In the field of diagnosis radiology the Federal Commission for the Protection against Sanitary Risks, has the mission to ensure the patients

Final treatment of liquid radioactive wastes

International Nuclear Information System (INIS)

Svolik, S.

2004-01-01

Final treatment of liquid radioactive wastes which are produced by 1 st and 2 nd bloc of the Mochovce NPP, prepares the NPP in its natural range. The purpose of the equipment is liquidation of wastes, which are formed at production. Wastes are warehoused in the building of active auxiliary plants in the present time, where are reservoirs in which they are deposited. Because they are already feeling and in 2006 year they should be filled definitely, it is necessary to treat them in that manner, so as they may be liquidated. Therefore the Board of directors of the Slovenske elektrarne has disposed about construction of final treatment of liquid radioactive wastes in the Mochovce NPP. Because of transport the wastes have to be treated in the locality of power plant. Technically, the final treatment of the wastes will be interconnected with building of active operation by bridges. These bridges will transport the wastes for treatment into processing centre

Pancreatic arterial calcium stimulation in the diagnosis and localisation of persistent hyperinsulinemic hypoglycaemia of infancy

Energy Technology Data Exchange (ETDEWEB)

Chigot, V.; Brunelle, F. [Department of Radiology, Hopital des Enfants Malades, Paris (France); Lonlay, P. de; Nassogne, M.-C.; Delagne, V.; Saudubray, J.-M. [Dept. of Paediatrics, Hopital des Enfants Malades, Paris (France); Laborde, K. [Dept. of Biology, Hopital des Enfants Malades, Paris (France); Fournet, J.-C. [Dept. of Pathology, Hopital des Enfants Malades, Paris (France); Nihoul-Fekete, C. [Department of Surgery, Hopital des Enfants Malades, Paris (France)

2001-09-01

Persistent hyperinsulinemic hypoglycaemia of infancy (PHHI) is often resistant to medical therapy. Surgery is therefore necessary. It is due to focal adenomatous islet-cell hyperplasia treatable by partial pancreatectomy, or diffuse beta-cell hyperfunction, which requires near-total pancreatectomy. Pancreatic venous sampling (PVS) is the reference technique for the preoperative diagnosis and localization of focal forms of PHHI in the pancreas. However, hypoglycaemia is necessary to analyse the results and PVS is technically challenging. Pancreatic arterial calcium stimulation (PACS) is technically easier and does not require hypoglycaemia. To study the accuracy in the diagnosis and localization of PHHI. Materials and methods: PACS was performed in 12 patients and correlated with histology. The accuracy of PACS is poor in diffuse lesions since only two of six cases were correctly identified by this test. Five of six focal lesions were correctly recognized and located. PACS is less accurate than PVS in PHHI. Currently, it should be performed only when PVS fails. (orig.)

Pancreatic arterial calcium stimulation in the diagnosis and localisation of persistent hyperinsulinemic hypoglycaemia of infancy

International Nuclear Information System (INIS)

Chigot, V.; Brunelle, F.; Lonlay, P. de; Nassogne, M.-C.; Delagne, V.; Saudubray, J.-M.; Laborde, K.; Fournet, J.-C.; Nihoul-Fekete, C.

2001-01-01

Persistent hyperinsulinemic hypoglycaemia of infancy (PHHI) is often resistant to medical therapy. Surgery is therefore necessary. It is due to focal adenomatous islet-cell hyperplasia treatable by partial pancreatectomy, or diffuse beta-cell hyperfunction, which requires near-total pancreatectomy. Pancreatic venous sampling (PVS) is the reference technique for the preoperative diagnosis and localization of focal forms of PHHI in the pancreas. However, hypoglycaemia is necessary to analyse the results and PVS is technically challenging. Pancreatic arterial calcium stimulation (PACS) is technically easier and does not require hypoglycaemia. To study the accuracy in the diagnosis and localization of PHHI. Materials and methods: PACS was performed in 12 patients and correlated with histology. The accuracy of PACS is poor in diffuse lesions since only two of six cases were correctly identified by this test. Five of six focal lesions were correctly recognized and located. PACS is less accurate than PVS in PHHI. Currently, it should be performed only when PVS fails. (orig.)

Diagnosis of acute atlanto-axial rotatory fixation in adults

International Nuclear Information System (INIS)

Stenson, Debbie

2011-01-01

This case report presents a case of a Fielding and Hawkins Type I AARF in an adult following trauma. It is presented to draw attention to the medical and technical details associated with the management of this rare spinal injury. The importance of imaging in the diagnosis and management of AARF is discussed. Early recognition and treatment of AARF is paramount in the avoidance of subsequent deformity and instability in these patients and are the key to the prevention of operable treatment.

B-cell lymphoma of the heart: A rare diagnosis.

Science.gov (United States)

Matos, António P; Palas, João; Doulaptsis, Constantinos; Ramalho, Miguel; Duarte, Sérgio; Bogaert, Jan

2014-12-01

We present a case of a primary cardiac lymphoma in a 60-year-old woman. The clinical presentation was non-specific and the diagnosis was suggested by its appearance on multidetector computed tomography. The final diagnosis was achieved by histopathological study and was corroborated by a decrease in tumor volume after targeted chemotherapy. A brief review of the appearance of primary cardiac lymphomas in imaging studies is presented. Copyright © 2014 Sociedade Portuguesa de Cardiologia. Published by Elsevier España. All rights reserved.

Early diagnosis of congenital dislocation of the hip

International Nuclear Information System (INIS)

Grill, F.

1984-01-01

Neonatal hip examination is only effective with the help of a large number of experts. Teamwork between pediatrician, pediatric orthopedic surgeon and general practitioner seems to be essential. Best results can be achieved with a hip examination during the first 4 days of life and controls with 3 months and with 12 months. The technic of clinical examination and diagnosis is described. Because of hip dysplasias without any clinical signs the importance of an x-ray of the hip with an age of 3 months is emphasized. (Author)

Sciatic nerve blocks for diagnosis of piriformis syndrome

International Nuclear Information System (INIS)

Owashi, Kazuya; Harada, Mikio; Utsumi, Hideaki; Sugawara, Hirobumi; Oyama, Kaori; Takei, Isao

2010-01-01

We used sciatic nerve block (SNB) to make the differential diagnosis of piriformis syndrome in 188 consecutive patients with sciatica in whom it was impossible to make the diagnosis based on the lumbar MRI findings. We rated the effectiveness of SNB as excellent (60%), good (25%) and poor (15%). After performing SNBs, lumbar radicular blocks, and surgeries based on the initial diagnosis, the final diagnoses were piriformis syndrome (56%), piriformis syndrome complicated with lumbar degenerative disease (4%), lumbar degenerative disease (23%), others or unknown (16%). The prevalence of piriformis syndrome in the excellent effectiveness group was 81%. SNB was effective in all patients with piriformis syndrome and in 66% of the lumbar degeneration patients. The diagnostic value of SNB is of limited value for differentiating piriformis syndrome from lumbar degenerative disease. (author)

Solar Living House Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Walters, Bradley [Univ. of Florida, Gainesville, FL (United States)

2017-03-09

permanent site constructions. This project suggest that high-performance buildings can be realized for more modest budgets. Public Benefits: Work on the Solar Living House and Solar Decathlon 2015 offered our student team unparalleled learning opportunities. Because of the duration of the project, a number of students participated at different points in their education, from first year undergraduates all the way through to advanced graduate students. The opportunity for collaboration with students and faculty from the National University of Singapore was also extraordinary, allowing for a sharing of technical knowledge and cultural exchange. The wider public has benefited from this work as its findings have been shared through public presentations and publications. It serves as a useful stepping stone along the path towards affordable, high-performance buildings.

IPEN scientific and technical publications 1984-1986

International Nuclear Information System (INIS)

1988-01-01

The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/STP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this 1984-1986 supplement include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. In this 1984-1986 supplement 458 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

IPEN Scientific and technical publications 1982-1983

International Nuclear Information System (INIS)

1984-01-01

The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/STP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this 1982-1983 supplement include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. In this 1982-1983 supplement 131 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

Technical concept for a Greater Confinement Disposal test facility

International Nuclear Information System (INIS)

Hunter, P.H.

1982-01-01

For the past two years, Ford, Bacon and Davis has been performing technical services for the Department of Energy at the Nevada Test Site in specific development of defense low-level waste management concepts for greater confinement disposal concept with particular application to arid sites. The investigations have included the development of Criteria for Greater Confinement Disposal, NVO-234, which was published in May of 1981 and the draft of the technical concept for Greater Confinement Disposal, with the latest draft published in November 1981. The final draft of the technical concept and design specifications are expected to be published imminently. The document is prerequisite to the actual construction and implementation of the demonstration facility this fiscal year. The GCD Criteria Document, NVO-234 is considered to contain information complimentary and compatible with that being developed for the reserved section 10 CFR 61.51b of the NRCs proposed licensing rule for low level waste disposal facilities

Sensor fault diagnosis of aero-engine based on divided flight status

Science.gov (United States)

Zhao, Zhen; Zhang, Jun; Sun, Yigang; Liu, Zhexu

2017-11-01

Fault diagnosis and safety analysis of an aero-engine have attracted more and more attention in modern society, whose safety directly affects the flight safety of an aircraft. In this paper, the problem concerning sensor fault diagnosis is investigated for an aero-engine during the whole flight process. Considering that the aero-engine is always working in different status through the whole flight process, a flight status division-based sensor fault diagnosis method is presented to improve fault diagnosis precision for the aero-engine. First, aero-engine status is partitioned according to normal sensor data during the whole flight process through the clustering algorithm. Based on that, a diagnosis model is built for each status using the principal component analysis algorithm. Finally, the sensors are monitored using the built diagnosis models by identifying the aero-engine status. The simulation result illustrates the effectiveness of the proposed method.

Sensor fault diagnosis of aero-engine based on divided flight status.

Science.gov (United States)

Zhao, Zhen; Zhang, Jun; Sun, Yigang; Liu, Zhexu

2017-11-01

Fault diagnosis and safety analysis of an aero-engine have attracted more and more attention in modern society, whose safety directly affects the flight safety of an aircraft. In this paper, the problem concerning sensor fault diagnosis is investigated for an aero-engine during the whole flight process. Considering that the aero-engine is always working in different status through the whole flight process, a flight status division-based sensor fault diagnosis method is presented to improve fault diagnosis precision for the aero-engine. First, aero-engine status is partitioned according to normal sensor data during the whole flight process through the clustering algorithm. Based on that, a diagnosis model is built for each status using the principal component analysis algorithm. Finally, the sensors are monitored using the built diagnosis models by identifying the aero-engine status. The simulation result illustrates the effectiveness of the proposed method.

Potentialities of the X-ray endoscopic diagnosis of stomach syphilis

International Nuclear Information System (INIS)

Dmitrieva, S.D.; Gurova, S.V.; Kovalenko, S.F.; Popova, G.N.; Legostaev, V.M.

1999-01-01

The possibilities of roentgenoendoscopic diagnostics of stomach syphilis are demonstrated by disease cases. Three forms of the stomach syphilis: tumor-like, infiltration and ulcerous ones are identified both roentgenological and endoscopic. Any infiltration process in the stomach of a young patient determined roentgenological should be reasoned as a sign of alterness relative to the syphilis. To perform endoscopic diagnosis of the stomach syphilis is easier than roentgenological one. The final syphilis diagnosis is impossible without blood test [ru

75 FR 2860 - Hydrogen and Fuel Cell Technical Advisory Committee (HTAC)

Science.gov (United States)

2010-01-19

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Hydrogen and Fuel Cell... Energy. ACTION: Notice of Open Meeting. SUMMARY: The Hydrogen and Fuel Cell Technical Advisory Committee... change; updates will be posted on http://hydrogen.energy.gov and copies of the final agenda will...

Final Technical Report_Clean Energy Program_SLC-SELF

Energy Technology Data Exchange (ETDEWEB)

Henderson, Glenn; Coward, Doug

2014-01-22

This is the Final Technical Report for DOE's Energy Efficiency and Conservation Block Grant, Award No. DE-EE0003813, submitted by St. Lucie County, FL (prime recipient) and the Solar and Energy Loan Fund (SELF), the program's third-party administrator. SELF is a 501(c)(3) and a certified Community Development Financial Institution (CDFI). SELF is a community-based lending organization that operates the Clean Energy Loan Program, which focuses on improving the overall quality of life of underserved populations in Florida with an emphasis on home energy improvements and cost-effective renewable energy alternatives. SELF was launched in 2010 through the creation of the non-profit organization and with a $2.9 million Energy Efficiency and Conservation Block (EECBG) grant from the U.S. Department of Energy (DOE). SELF has its main office and headquarters in St. Lucie County, in the region known as the Treasure Coast in East-Central Florida. St. Lucie County received funding to create SELF as an independent non-profit institution, outside the control of local government. This was important for SELF to create its identity as an integral part of the business community and to help in its quest to become a Community Development Financial Institution (CDFI). This goal was accomplished in 2013, allowing SELF to focus on its mission to increase energy savings while serving markets that have struggled to find affordable financial assistance. These homeowners are most impacted by high energy costs. Energy costs are a disproportionate percentage of household expenses for low to moderate income (LMI) households. Electricity costs have been steadily rising in Florida by nearly 5% per year. Housing in LMI neighborhoods often includes older inefficient structures that further exacerbate the problem. Despite the many available clean energy solutions, most LMI property owners do not have the disposable income or equity in their homes necessary to afford the high upfront cost

Algebraic approach for the diagnosis of turbine cycles in nuclear power plants

International Nuclear Information System (INIS)

Heo, Gyunyoung; Chang, Soon Heung

2005-01-01

According to plant operating staff's practical needs, authors proposed a diagnosis model to identify the performance degradation of steam turbine cycles in nuclear power plants (NPPs). The essential idea of this study is how to identify the intrinsically degraded component which causes electric loss. Authors found that there were not so many turbine cycle diagnosis applications in NPPs currently because of technical, financial, or social characteristics of the plant. So a great part of the diagnosis has been dependent on operating staff's experience and knowledge. However as economic competition becomes severe, the efficiency staffs is asking for reliable and practical advisory tools. For the solution of these shortcomings, authors proposed a simple and intuitive diagnosis concept based on the superposition rule of degradation phenomena, which can be derived by simple algebra and correlation analysis. Though the superposition rule is not so significant statistically, almost all of the performance indices under normal operation are fairly compatible with this model. Authors developed a prototype model of quantitative root-cause diagnosis and validated the background theory using the simulated data. The turbine cycle advisory system using this model was applied to Gori NPP units 3 and 4

[Computer-aided Diagnosis and New Electronic Stethoscope].

Science.gov (United States)

Huang, Mei; Liu, Hongying; Pi, Xitian; Ao, Yilu; Wang, Zi

2017-05-30

Auscultation is an important method in early-diagnosis of cardiovascular disease and respiratory system disease. This paper presents a computer-aided diagnosis of new electronic auscultation system. It has developed an electronic stethoscope based on condenser microphone and the relevant intelligent analysis software. It has implemented many functions that combined with Bluetooth, OLED, SD card storage technologies, such as real-time heart and lung sounds auscultation in three modes, recording and playback, auscultation volume control, wireless transmission. The intelligent analysis software based on PC computer utilizes C# programming language and adopts SQL Server as the background database. It has realized play and waveform display of the auscultation sound. By calculating the heart rate, extracting the characteristic parameters of T1, T2, T12, T11, it can analyze whether the heart sound is normal, and then generate diagnosis report. Finally the auscultation sound and diagnosis report can be sent to mailbox of other doctors, which can carry out remote diagnosis. The whole system has features of fully function, high portability, good user experience, and it is beneficial to promote the use of electronic stethoscope in the hospital, at the same time, the system can also be applied to auscultate teaching and other occasions.

[Cystic fibrosis--initial diagnosis in a 39-year-old patient].

Science.gov (United States)

Bargon, J; Rickmann, J; Jacobi, V; Straub, R; Arnemann, J; Wagner, T O

2000-12-15

Cystic fibrosis is the most common hereditary disorder among Caucasians. Most of the patients are diagnosed as children. However, some cases are going undiagnosed into adulthood and are then often misdiagnosed because the non-pediatricians do not know cystic fibrosis very well and do not consider this diagnosis in adult patients. We present the medical history of a woman, who was diagnosed with cystic fibrosis at the age of 39 years, although she had suffered from bronchiectasis, pancreatic insufficiency and liver cirrhosis since many years. Her medical history was long with some diagnosis, but because of her age nobody considered the final diagnosis. In adult patients with bronchiectasis, liver cirrhosis and pancreatic insufficiency in combination or with only one of these symptoms, cystic fibrosis should be included into the differential diagnosis.

Power system technical performance issues related to the application of long HVAC cables

DEFF Research Database (Denmark)

Wiechowski, on behalf of Cigre WG C4.502, W.; Sluis, L. V. der; Ohno, Teruo

2011-01-01

This paper reports the progress of work of Cigre Working Group C4.502 “Power system technical performance issues related to the application of long HVAC cables”. The primary goal of the WG C4.502 is to write a technical brochure that will serve as practical guide for performing studies necessary...... for assessing the technical performance of HV/EHV systems with large share of AC cable lines. This paper besides providing a background for formulation of WG C4.502 and its overall aim, describes the tasks that were accomplished before the interim report was submitted to Study Committee C4 System Technical...... Performance in August 2010. The work in the WG is ongoing and final report will be ready according to the time schedule in 2012. The focus of this paper is in particular to show all issues related to system technical performance with assigned weights in terms of their importance and/or uniqueness for cable...

Flow in porous media, phase behavior and ultralow interfacial tensions: mechanisms of enhanced petroleum recovery. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Davis, H.T.; Scriven, L.E.

1982-01-01

A major program of university research, longer-ranged and more fundamental in approach than industrial research, into basic mechanisms of enhancing petroleum recovery and into underlying physics, chemistry, geology, applied mathematics, computation, and engineering science has been built at Minnesota. The 1982 outputs of the interdisciplinary team of investigators were again ideas, instruments, techniques, data, understanding and skilled people: forty-one scientific and engineering papers in leading journals; four pioneering Ph.D. theses; numerous presentations to scientific and technical meetings, and to industrial, governmental and university laboratories; vigorous program of research visits to and from Minnesota; and two outstanding Ph.D.'s to research positions in the petroleum industry, one to a university faculty position, one to research leadership in a governmental institute. This report summarizes the 1982 papers and theses and features sixteen major accomplishments of the program during that year. Abstracts of all forty-five publications in the permanent literature are appended. Further details of information transfer and personnel exchange with industrial, governmental and university laboratories appear in 1982 Quarterly Reports available from the Department of Energy and are not reproduced here. The Minnesota program continues in 1983, notwithstanding earlier uncertainty about the DOE funding which finally materialized and is the bulk of support. Supplemental grants-in-aid from nine companies in the petroleum industry are important, as are the limited University and departmental contributions. 839 references, 172 figures, 29 tables.

Technical structure of the global nanoscience and nanotechnology literature

Energy Technology Data Exchange (ETDEWEB)

Kostoff, Ronald N., E-mail: kostofr@onr.navy.mil; Koytcheff, Raymond G. [Office of Naval Research (United States); Lau, Clifford G. Y. [Institute for Defense Analyses (United States)

2007-10-15

Text mining was used to extract technical intelligence from the open source global nanotechnology and nanoscience research literature. An extensive nanotechnology/nanoscience-focused query was applied to the Science Citation Index/Social Science Citation Index (SCI/SSCI) databases. The nanotechnology/nanoscience research literature technical structure (taxonomy) was obtained using computational linguistics/document clustering and factor analysis. The infrastructure (prolific authors, key journals/institutions/countries, most cited authors/journals/documents) for each of the clusters generated by the document clustering algorithm was obtained using bibliometrics. Another novel addition was the use of phrase auto-correlation maps to show technical thrust areas based on phrase co-occurrence in Abstracts, and the use of phrase-phrase cross-correlation maps to show technical thrust areas based on phrase relations due to the sharing of common co-occurring phrases. The {approx}400 most cited nanotechnology papers since 1991 were grouped, and their characteristics generated. Whereas the main analysis provided technical thrusts of all nanotechnology papers retrieved, analysis of the most cited papers allowed their characteristics to be displayed. Finally, most cited papers from selected time periods were extracted, along with all publications from those time periods, and the institutions and countries were compared based on their representation in the most cited documents list relative to their representation in the most publications list.

Technical structure of the global nanoscience and nanotechnology literature

International Nuclear Information System (INIS)

Kostoff, Ronald N.; Koytcheff, Raymond G.; Lau, Clifford G. Y.

2007-01-01

Text mining was used to extract technical intelligence from the open source global nanotechnology and nanoscience research literature. An extensive nanotechnology/nanoscience-focused query was applied to the Science Citation Index/Social Science Citation Index (SCI/SSCI) databases. The nanotechnology/nanoscience research literature technical structure (taxonomy) was obtained using computational linguistics/document clustering and factor analysis. The infrastructure (prolific authors, key journals/institutions/countries, most cited authors/journals/documents) for each of the clusters generated by the document clustering algorithm was obtained using bibliometrics. Another novel addition was the use of phrase auto-correlation maps to show technical thrust areas based on phrase co-occurrence in Abstracts, and the use of phrase-phrase cross-correlation maps to show technical thrust areas based on phrase relations due to the sharing of common co-occurring phrases. The ∼400 most cited nanotechnology papers since 1991 were grouped, and their characteristics generated. Whereas the main analysis provided technical thrusts of all nanotechnology papers retrieved, analysis of the most cited papers allowed their characteristics to be displayed. Finally, most cited papers from selected time periods were extracted, along with all publications from those time periods, and the institutions and countries were compared based on their representation in the most cited documents list relative to their representation in the most publications list

Final Technical Report - In-line Uranium Immunosensor

International Nuclear Information System (INIS)

Blake, Diane A.

2006-01-01

In this project, personnel at Tulane University and Sapidyne Instruments Inc. developed an in-line uranium immunosensor that could be used to determine the efficacy of specific in situ biostimulation approaches. This sensor was designed to operate autonomously over relatively long periods of time (2-10 days) and was able to provide near real-time data about uranium immobilization in the absence of personnel at the site of the biostimulation experiments. An alpha prototype of the in-line immmunosensor was delivered from Sapidyne Instruments to Tulane University in December of 2002 and a beta prototype was delivered in November of 2003. The beta prototype of this instrument (now available commercially from Sapidyne Instruments) was programmed to autonomously dilute standard uranium to final concentrations of 2.5 to 100 nM (0.6 to 24 ppb) in buffer containing a fluorescently labeled anti-uranium antibody and the uranium chelator, 2,9-dicarboxyl-1,10-phenanthroline. The assay limit of detection for hexavalent uranium was 5.8 nM or 1.38 ppb. This limit of detection is well below the drinking water standard of 30 ppb recently promulgated by the EPA. The assay showed excellent precision; the coefficients of variation (CV's) in the linear range of the assay were less than 5% and CV?s never rose above 14%. Analytical recovery in the immunosensors-based assay was assessed by adding variable known quantities of uranium to purified water samples. A quantitative recovery (93.75% - 108.17%) was obtained for sample with concentrations from 7.5 to 20 nM (2-4.75 ppb). In August of 2005 the sensor was transported to Oak Ridge National Laboratory, for testing of water samples at the Criddle test site (see Wu et al., Environ. Sci. Technol. 40:3978-3985 2006 for a description of this site). In this first on-site test, the in-line sensor was able to accurately detect changes in the concentrations of uranium in effluent samples from this site. Although the absolute values for the uranium

The chest X-ray manifestations of children with highly pathogenic H5N1 avian influenza virus infection (a report of 1 final diagnosis case and 1 borderline case)

International Nuclear Information System (INIS)

Jin Ke; Chen Hua; Tan Lihua; Yuan Youhong; Xiao Enhua; Luo Ruping; Li Wanging; Xu Heping

2006-01-01

Objective: To describe the chest X-ray manifestations of children with highly pathogenic H5N1 avian influenza virus infection. Methods: The pulmonary X-ray findings in 1 patient was confirmed by the World Health Organization infected H5N1 avian influenza vires and 1 borderline patient was retrospectively analyzed. Results: Both sides of lung field showed the cloudy and massive infiltration in chest X-ray film. The lesions of lung distributed extensively and symmetrically. Radiological dynamic changes showed the variation of the lesions of lung was quick in a short time. It had a characteristic of roving around. The lesions of lung appeared fibrosis at the period of the end. Conclusion: There are some radiographic characteristics in children with H5N1 avian influenza vires infection. It will be helpful for its diagnosis when getting familiar with its X-ray manifestations, but the final diagnosis is dependent on the epidemiology history and laboratory results. (authors)

A study on the systematic framework to develop effective diagnosis procedures of nuclear power plants

International Nuclear Information System (INIS)

Park, Jinkyun; Jung, Wondea

2004-01-01

In complex systems such as the nuclear and chemical industry, the importance of a diagnosis procedure has been well recognized, since identifying the nature of an on-going event should be preceded to determine successful countermeasures or remedial actions. Unfortunately, a systematic framework that can suggest a unified and consistent process for constructing useful diagnosis procedures seems to be scant. In this paper, the systematic framework that can provide a sound way in constructing a diagnosis procedure is suggested based on two kinds of technical bases, such as the decision-making strategies of human and the test sequencing technique. To demonstrate the appropriateness of suggested framework, the diagnosis procedure of the reference nuclear power plant is reformed based on it. Subjective ratings are conducted to compare reformed procedure with the original one, and results support that operators' performance in an event diagnosis could be improved. Thus, although well designed experiments are needed to draw a reliable conclusion, it is expected that suggested framework could be applied to provide a consistent process in constructing useful diagnosis procedures

76 FR 19267 - Pilot, Flight Instructor, and Pilot School Certification; Technical Amendment

Science.gov (United States)

2011-04-07

.... No. 61-127] RIN 2120-AI86 Pilot, Flight Instructor, and Pilot School Certification; Technical... for pilots, flight instructors, ground instructors, and pilot schools. This document reinstates two... entitled, ``Pilot, Flight Instructor, and Pilot School Certification; Final Rule'' (74 FR 42500). That...

Design and technical status of the EU contribution to ITER

International Nuclear Information System (INIS)

Gasparotto, Maurizio; Federici, Gianfranco; Casci, Federico Riccardo

2009-01-01

Europe is involved in the procurement of most of the high-technology items for the ITER device (e.g. parts of the superconducting Toroidal (TF) and Poloidal Field (PF) coils, the vacuum vessel (VV), the in-vessel components, the remote handling, the additional heating systems, the tritium plant and cryoplant and finally parts of the diagnostics). In many cases the technologies required to manufacture these components are well established, in others there is still ongoing design and R and D work to select and optimise the final design solutions and to consolidate the underlying technologies as, for example, in the areas of heating and current drive, plasma diagnostics, shield blanket and first wall, remote handling, etc. A design review has recently been conducted by the ITER Organisation, with the support of the Domestic Agencies (DAs) established by the countries participating to ITER, to address the remaining outstanding technical issues and understand the associated implications for design, machine performance, schedule and cost. This paper provides an update of the design and technical status of EU contributions to ITER.

Technical Efficiency and Organ Transplant Performance: A Mixed-Method Approach

Science.gov (United States)

de-Pablos-Heredero, Carmen; Fernández-Renedo, Carlos; Medina-Merodio, Jose-Amelio

2015-01-01

Mixed methods research is interesting to understand complex processes. Organ transplants are complex processes in need of improved final performance in times of budgetary restrictions. As the main objective a mixed method approach is used in this article to quantify the technical efficiency and the excellence achieved in organ transplant systems and to prove the influence of organizational structures and internal processes in the observed technical efficiency. The results show that it is possible to implement mechanisms for the measurement of the different components by making use of quantitative and qualitative methodologies. The analysis show a positive relationship between the levels related to the Baldrige indicators and the observed technical efficiency in the donation and transplant units of the 11 analyzed hospitals. Therefore it is possible to conclude that high levels in the Baldrige indexes are a necessary condition to reach an increased level of the service offered. PMID:25950653

The pedagogical professional development of the English teacher in the Professional and Technical Education

Directory of Open Access Journals (Sweden)

Rosa María Padrón Otaño

2017-12-01

Full Text Available The teacher of English in Informatics studies in the Professional and Technical Education shows an insufficient preparation to plan the teaching learning process of reading comprehension in professional contexts, a fact that affects the communicative development of their students. The limitations in the development of these teachers of English were confirmed as one of the key causes. This research follows a dialectical materialist philosophy. In the diagnosis and the evaluation empirical methods such as the interview to teachers of English and document analysis, specialist criterion and a preexperimental design were used. The main research outcome is a contextualized pedagogical professional development strategy. The strategy comprises scientific foundations, diagnosis, general objective, specific actions and the evaluation. The main action of the strategy is postgraduate course to develop the pedagogical professional skills in the use of a methodology which promotes the development of knowledge and skills in both the technical sphere and a specialized didactics (Content and Language Integrated Learning. The practical implementation of the strategy elaborated seemed to allow the teachers of English to be able to plan their lessons using this methodology, and to show a new attitude which meant their active involvement in the creation of a community of learning with higher levels of interdisciplinary collaboration between the teachers of English and those of the technical sphere, as well as an effective management of their own continuing professional development.

Predictors of employer satisfaction: technical and non-technical skills.

Science.gov (United States)

Danielson, Jared A; Wu, Tsui-Feng; Fales-Williams, Amanda J; Kirk, Ryan A; Preast, Vanessa A

2012-01-01

Employers of 2007-2009 graduates from Iowa State University College of Veterinary Medicine were asked to respond to a survey regarding their overall satisfaction with their new employees as well as their new employees' preparation in several technical and non-technical skill areas. Seventy-five responses contained complete data and were used in the analysis. Four technical skill areas (data collection, data interpretation, planning, and taking action) and five non-technical skill areas (interpersonal skills, ability to deal with legal issues, business skills, making referrals, and problem solving) were identified. All of the skill area subscales listed above had appropriate reliability (Cronbach's alpha>0.70) and were positively and significantly correlated with overall employer satisfaction. Results of two simultaneous regression analyses indicated that of the four technical skill areas, taking action is the most salient predictor of employer satisfaction. Of the five non-technical skill areas, interpersonal skills, business skills, making referrals, and problem solving were the most important skills in predicting employer satisfaction. Hierarchical regression analysis revealed that all technical skills explained 25% of the variation in employer satisfaction; non-technical skills explained an additional 42% of the variation in employer satisfaction.

Multi-centre retrospective analysis of clinical diagnosis and treatment for chronic cough

Directory of Open Access Journals (Sweden)

Xiao-ming CHENG

2011-02-01

Full Text Available Objective To explore the clinical characteristics and the present status of diagnosis and treatment of chronic cough.Methods The clinical data of 238 in-patients and out-patients of Departments of Respiratory Diseases from 4 teaching hospitals of Chongqing Municipality were collected from Oct.2008 to Dec.2009,and their clinical characteristics,diagnosis and therapeutic effects were retrospectively analyzed.Results A total of 238 patients were enrolled,most of them complained of dry cough and night cough.Throat symptoms were most common,including itching or foreign body sensation,throat discomfort and gastro-oesophageal reflux.Congestion of pharynx and cobblestone like changes in posterior pharyngeal wall were the most common signs in patients with chronic cough.Among all the supplementary examinations,bronchial provocation test resulted in highest positive rate.Etiological diagnosis was done in a total of 254 case-times for diseases leading to chronic cough,among them upper airway cough syndrome(UACS was suspected in 115 case-times.cough variant asthma(CVA in 42 case-times,and cough due to gastroesophageal reflux(GERC in 53 case-times.After the specific treatment targeting UACS,CVA and GERC,in 152 case-times improvement was found after follow-up,including 56,27 and 21 case-times,respectively,with an effective rate of 68.4%(104/152.The final diagnosis for the other 44 case-times with chronic cough was chronic tonsillitis,chronic bronchitis,eosinophilic bronchitis and angiotensin converting enzyme inhibitor(ACEI induced cough.A definite diagnosis was finally made in 148 out of a total of 254 casses,with a diagnostic rate of 58.3%(148/254.Conclusion The final diagnostic rate in etiology of chronic cough is still poor nowadays in our country,and empirical treatment is still the main practice for chronic cough.

Technical standards in the law of technical safety

International Nuclear Information System (INIS)

Marburger, P.

1985-01-01

Technical standards are of great importance for the closer definition of inexact terms of law, for instance ''generally accepted technical rules'', ''state of the art'', ''state of science and technology'' or similar normative terms, in the law of technical safety. The paper discusses with whom the authority for regulating this sector of law rests, deals with the different ways of how technical standards are used by the law (''anticipated expert opinion'', reference to such standards in law and administration) and points out demands on the procedure of standardization. (orig.) [de

Review:Whole genome amplification in preimplantation genetic diagnosis

Institute of Scientific and Technical Information of China (English)

Ying-ming ZHENG; Ning WANG; Lei LI; Fan JIN

2011-01-01

Preimplantation genetic diagnosis(PGD)refers to a procedure for genetically analyzing embryos prior to implantation,improving the chance of conception for patients at high risk of transmitting specific inherited disorders.This method has been widely used for a large number of genetic disorders since the first successful application in the early 1990s.Polymerase chain reaction(PCR)and fluorescent in situ hybridization(FISH)are the two main methods in PGD,but there are some inevitable shortcomings limiting the scope of genetic diagnosis.Fortunately,different whole genome amplification(WGA)techniques have been developed to overcome these problems.Sufficient DNA can be amplified and multiple tasks which need abundant DNA can be performed.Moreover,WGA products can be analyzed as a template for multi-loci and multi-gene during the subsequent DNA analysis.In this review,we will focus on the currently available WGA techniques and their applications,as well as the new technical trends from WGA products.

Technical Feasibility and Oncological Legitimacy of Enucleation of Intraductal Papillary Mucinous Neoplasm Located at the Pancreatic Head or Uncinate Process.

Science.gov (United States)

Soejima, Yuji; Toshima, Takeo; Motomura, Takashi; Yokota, Tomoyuki; Joko, Kouji; Oshiro, Yumi; Takahashi, Ikuo; Nishizaki, Takashi; Maehara, Yoshihiko

2017-01-01

Surgical indications and strategies for branch duct (BD)-intraductal papillary mucinous neoplasm (IPMN) at the pancreatic head (PH) are controversial issues. We investigated the technical feasibility and oncological legitimacy of enucleation for IPMN of the PH. The clinicopathological parameters of 11 patients with IPMN who underwent conventional pancreaticoduodenectomy (PD, n=7) or enucleation (n=4) during the same period were evaluated. The mean operative time (442 vs. 280 min, p<0.05) and blood loss (864 vs. 93 ml, p<0.05) were significantly better in the enucleation group. The final pathological diagnosis (low-/intermediate-/high-grade dysplasia) in the PD and enucleation groups was 4/2/1 and 3/1/0, respectively. The incidence of grade B pancreatic fistula and Clavien III complications was 14% vs. 0% and 43% vs. 25%, respectively. No recurrent pancreatitis or exocrine or endocrine dysfunction was noted in the enucleation group; however, de novo or exacerbated diabetes mellitus developed in three patients in the PD group. All patients were alive and no disease recurrence was noted at a mean follow-up of 1,059 days. Enucleation of BD-IPMN at the PH is a technically feasible and oncologically acceptable procedure which should be justified in patients with IPMNs with a low risk of malignancy. Copyright© 2017 International Institute of Anticancer Research (Dr. John G. Delinassios), All rights reserved.

Diagnosis of the operation state of photovoltaic water pumping systems installed in Pernambuco state, Brazil; Diagnostico do estado de funcionamento de sistemas de bombeamento de agua fotovoltaico (SBFV) instalados em Pernambuco

Energy Technology Data Exchange (ETDEWEB)

Costa, Heitor Scalambrini [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Nucleo de Apoio a Projetos de Energias Renovaveis], Email: hscosta@ufpe.br

2006-07-01

The major projects concerning the dissemination of the use of photovoltaic solar energy (PVSE) in Brazil are located in the Northeast region. Particularly, the state of Pernambuco has the largest number of installations and the largest installed power of autonomous systems. There exist approximately 700 residencies, 250 schools and 150 water pumping systems among other applications using PVSE, totaling 250 k Wp installed in more than 80 cities of that State. This work analyses a diagnosis report on the state of functioning of 64 one-year-old water-pumping installations in 30 m to 60 m depth wells, driven by 300 to 1,600 Wp photovoltaic generators, the flows varying from 200 l/h to 6,000 l/h. Technical and non-technical problems were identified, ranging from improper location choice, wrong system dimensioning, inadequate photovoltaic generator installations, lack of user instruction and training, lack of responsibility definitions regarding the technical assistance and the needed follow-up. In the final part of this report proposals are enumerated concerning the establishment of a local and municipal organizing structure aiming the management of the water-pumping installations and the assurance of a larger success probability in the use of that technology. (author)

Method for assessment of the technical potential of the plant agricultural waste suitable for energy purposes in Bulgaria

International Nuclear Information System (INIS)

Georgiev, V.

2004-01-01

A method for assessment of technical potential of quantitatively important plant agriculture waste; straw from wheat and barley; corn stalks; sunflower stalks and heads; tobacco stalks; orchard prunings and vineyard prunings suitable for energy purposes for Bulgarian conditions is developed. Data for assessment of the technical potential for 2002 using this method are presented. A comparison between technical potential of mentioned wastes, final energy consumption in agriculture and all branches of Bulgarian economy for 2002 is made. (author)

75 FR 16345 - Administrative Practices and Procedures; Good Guidance Practices; Technical Amendment

Science.gov (United States)

2010-04-01

.... FDA-1999-N-3539] (formerly Docket No. 1999N-4783) Administrative Practices and Procedures; Good Guidance Practices; Technical Amendment AGENCY: Food and Drug Administration, HHS. ACTION: Final rule... Subjects in 21 CFR Part 10 Administrative practice and procedure, News media. 0 Therefore, under the...

Overview of technical Issues Associated with the Long Term Storage of Light Water Reactor used Nuclear Fuel

International Nuclear Information System (INIS)

Sorenson, Ken B.

2014-01-01

The nuclear power technical community is developing the technical basis for demonstrating the safety of storing used nuclear fuel for extended periods of time. The combination of reactor operations that off-load spent fuel to interim storage, coupled with delays in repository construction, has resulted in the expectation that storage periods may be for longer periods of time than originally intended. As more fuel continues to be off-loaded from operating reactors, the need for expanded interim storage also increases. As repository programs are delayed, interim storage requirements will likely exceed licensing term limits. To address these operational realities, there has been a concerted international effort to identify and prioritize the technical issues that need to be addressed in order to demonstrate the safety of storing used nuclear fuel for extended periods of time. Since this is an international effort, different storage systems, regulations, and policies need to be considered. This results in differences in technical issues, as well as differences in priorities. However, this effort also identifies important commonalities in some technical areas that need to be addressed. A broad-based international evaluation of these technical issues provides a better understanding of technical concerns as they relate to individual storage systems and specific national regulatory frameworks. While there are several international activities underway that are focused on long term storage, this paper will discuss the activities of the Electric Power Research Institute (EPRI)/Extended Storage Collaboration Program (ESCP) International Subcommittee. A status report detailing the identification and prioritization of the technical issues was presented at the PSAM11 Conference in June 2012 (1). Since that conference, a final report has been completed by the EPRI/ESCP International Subcommittee (2). This paper will provide important results of the final report as well as

76 FR 64083 - Reliability Technical Conference; Notice of Technical Conference

Science.gov (United States)

2011-10-17

... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, November 29, 2011, from 1 p.m. to 5 p.m. and... reliability that were identified in earlier Commission technical conferences. The conference also will discuss...

Technical Meeting on Grading of the Application of Management System Requirements. Presentations

International Nuclear Information System (INIS)

2012-01-01

The objectives of this Technical Meeting are threefold: - to share international experiences and lessons learned, as well as exchange views on best practices and strategies to overcome the difficulties encountered; - to review and discuss the draft technical report on 'Grading the Application of Management System Requirements, to allow the participants to contribute to the improvement of the document and to enrich it with practical examples; and - to strengthen the international networking of specialists in the field. The topics covered during the meeting will include: - Examples and case studies presented by participants from countries with nuclear facilities (mainly focused on NPPs, and, where appropriate, from research reactors, fuel cycle and waste management facilities) on grading the application of management system requirements and lessons learned. - Reviewing and improving the final draft of a technical report on 'Grading the Application of Management System Requirements', which will supersede the previous guidance: Grading of Quality Assurance Requirement: A Manual (Technical Reports Series No. 328)

Final Technical Report, DOE Grant DE-FG02-98ER54496, Physics of High-Energy-Density X Pinch Plasmas

International Nuclear Information System (INIS)

Hammer, David

2008-01-01

Abstract for the Final Technical Report, DOE Grant DE-FG02-98ER54496 An X-pinch plasma is produced by driving a high current (100-500 kiloamperes) through two or more fine wires that cross and touch at a point, forming an X in the case of two wires. The wires explode because of the high current, and then the resulting plasma is imploded radially inward by the magnetic field from the current. When the imploding material briefly stagnates at very small radius and high density, an intense burst of x-rays is produced and the plasma disassembles as rapidly as it imploded. When this project began, we could confidently state that at its minimum radius, X pinch plasmas made from such materials as titanium and molybdenum might be as hot as 10,000,000 K and had densities almost as high as the solid wire density, but their X-ray pulse durations were below one billionth of a second. We could also say that the X pinch was useful for point-projection imaging of rapidly changing objects, such as exploding wires, with high resolution, indicative of a very small X-ray source spot size. We can now confidently say that X-pinch plasma temperatures at the moment of the X-ray burst are 10-25 million K in titanium, molybdenum and several other wire X-pinches based upon the spectrum of emitted X-rays in the radiation burst. By the same means, as well as from the penetration of X-rays through the dense plasma, we know that ion densities are close to or higher than one-tenth of the density of the original (solid) wire material in molybdenum and a few other X-pinch plasmas. Furthermore, using the diffraction of X-rays radiated by the X-pinch when it reaches minimum radius, we have determined that the x-ray source size is about 1 thousandth of a millimeter for such wire materials as molybdenum and niobium, while it is 2-10 times larger for tungsten, titanium and aluminum wires. Finally, using a very high speed X-ray imaging 'streak camera,' we have determined that X pinch X-ray pulses can be

Teaching Technical Writing - Towards Technical Writing

DEFF Research Database (Denmark)

Kastberg, Peter

2000-01-01

In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm that ...... of technical writing.......In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm...... that used to govern what the quality of an LSP text should be as opposed to the standpoint, which I advocate. By way of summing up, I will show how a university curriculum is designed so that - upon graduation - the technical translator could also be methodological quite well suited to take on the challenge...

Technical report on the accelerators

Energy Technology Data Exchange (ETDEWEB)

Bex, L [ed.

1996-12-31

GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d`Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d`Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.). 48 refs.

Technical report on the accelerators

International Nuclear Information System (INIS)

Bex, L.

1995-01-01

GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d'Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d'Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.)

Technical nuclear safety in France. Control by the governmental authority

International Nuclear Information System (INIS)

1991-12-01

In publishing this latest edition, we have endeavoured to provide the reader with the information necessary to obtain a full understanding of the regulatory system applied to ensure technical nuclear safety in France. As the reader will discover in the following pages, technical nuclear safety is a matter which must be settled in advance of the actual operation of civil nuclear installations; the primary requirement is to mobilize those involved to anticipate and prevent. The fundamental options on which the French system is based, the relationship between the operator and the safety authority must be clearly stated: independence of judgement and decision, complementarity of responsibilities. It is for the governmental authorities to determine the technical nuclear safety objectives, which are becoming more and more consistent if not unified throughout the world. It is for the operator to propose technical provisions in order to achieve these objectives. It is for the governmental authorities to verify, by technical safety analyses, the adequacy of the provisions in terms of the defined objectives. It is for the operator to properly implement these approved provisions. And, finally, it is for the governmental authorities to verify, by sampling, the quality of their implementation and to make from them the necessary regulatory inferences. This sequence of events requires permanent frank in-depth dialogue. The effectiveness of the regulatory action must therefore reside not in close technical restraint but in the interactions between responsible partners

Technical nuclear safety in France. Control by the governmental authority

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-12-15

In publishing this latest edition, we have endeavoured to provide the reader with the information necessary to obtain a full understanding of the regulatory system applied to ensure technical nuclear safety in France. As the reader will discover in the following pages, technical nuclear safety is a matter which must be settled in advance of the actual operation of civil nuclear installations; the primary requirement is to mobilize those involved to anticipate and prevent. The fundamental options on which the French system is based, the relationship between the operator and the safety authority must be clearly stated: independence of judgement and decision, complementarity of responsibilities. It is for the governmental authorities to determine the technical nuclear safety objectives, which are becoming more and more consistent if not unified throughout the world. It is for the operator to propose technical provisions in order to achieve these objectives. It is for the governmental authorities to verify, by technical safety analyses, the adequacy of the provisions in terms of the defined objectives. It is for the operator to properly implement these approved provisions. And, finally, it is for the governmental authorities to verify, by sampling, the quality of their implementation and to make from them the necessary regulatory inferences. This sequence of events requires permanent frank in-depth dialogue. The effectiveness of the regulatory action must therefore reside not in close technical restraint but in the interactions between responsible partners.

Factors Associated with Delayed Cancer Diagnosis in Egyptian Children

Directory of Open Access Journals (Sweden)

E.R. Abdelkhalek

2014-01-01

Full Text Available Background Despite tremendous importance of early cancer diagnosis in children, few studies on this topic have been conducted in Egypt. Early stage diagnosis can have a positive effect on prognoses and the quality of life of children with cancer. We investigated delays in the diagnosis of childhood cancers in Egypt and determined the factors associated with these delays. Methods This retrospective study included 172 children with cancer from two pediatric oncology units. The interval between symptoms onset and final diagnosis for each child was estimated and examined by univariate and multivariate analyses to determine correlations with the child's sex, age at diagnosis, type and site of malignancy, family residence, socioeconomic status, and parental educational level. Findings The median total diagnosis delay period was 47 days caused by patients and/or parents (8 days and diagnosis (28 days. Statistically significant patient factors associated with delayed diagnosis were age (<5 years, lower parental education, and socioeconomic status. Sex residence and family size were not significant. Malignancy type and tumor site significantly affected the time for diagnosis. The lowest median value was associated with germ cell tumors (GCTs and leukemia, and the highest value was in children with brain tumor. Missed diagnoses were initially recorded in 39.5% of the patients and were associated with patient and tumor factors. Interpretation Delayed diagnosis of childhood cancer is related to age, family, socioeconomic status and parental education, and cancer type and site. Efforts should be made to promote awareness, develop effective steps to eliminate possible contributing factors, and determine the best intervention method.

Monitoring as component for the decision making in final repository projects; Monitoring als Baustein fuer die Entscheidungsfindung in Endlagerprojekten

Energy Technology Data Exchange (ETDEWEB)

Kallenbach-Herbert, Beate; Alt, Stefan [Oeko-Institut e.V., Darmstadt (Germany)

2012-12-15

The monitoring in final radioactive waste repositories is performed by continuous or repeated measurements of technical and geologic parameters during long time periods. The collected data serve manifold purposes. The central focus is to provide fundamental information for the decision between and within the three phases of a final repository project. This means that monitoring is not only the sum of technical surveillance measures. Monitoring is also important for several sociopolitical decisions, for instance in case of closure of the repository. The article discusses possible objectives and shows the relevant technical aspects that are used deduce the requirements for an integrated monitoring concept. It is shown that a monitoring concept should be developed early enough involving all groups that are concerned by the waste disposal project.

A study on group decision-making based fault multi-symptom-domain consensus diagnosis

International Nuclear Information System (INIS)

He Yongyong; Chu Fulei; Zhong Binglin

2001-01-01

In the field of fault diagnosis for rotating machines, the conventional methods or the neural network based methods are mainly single symptom domain based methods, and the diagnosis accuracy of which is not always satisfactory. In this paper, in order to utilize multiple symptom domains to improve the diagnosis accuracy, an idea of fault multi-symptom-domain consensus diagnosis is developed. From the point of view of the group decision-making, two particular multi-symptom-domain diagnosis strategies are proposed. The proposed strategies use BP (Back-Propagation) neural networks as diagnosis models in various symptom domains, and then combine the outputs of these networks by two combination schemes, which are based on Dempster-Shafer evidence theory and fuzzy integral theory, respectively. Finally, a case study pertaining to the fault diagnosis for rotor-bearing systems is given in detail, and the results show that the proposed diagnosis strategies are feasible and more efficient than conventional stacked-vector methods

The radiological diagnosis of bone tumors

International Nuclear Information System (INIS)

Freyschmidt, J.

1979-01-01

Since the definitive diagnosis of very many bone tumors is not only histological but also radiological it is important that the latter examination be of high quality. Prior to biopsy the differential diagnosis should be narrowed down as far as possible radiologically. The radiological procedures include conventional X-ray examination in two projections, tomography, angiography, and computerized tomography. Tomography can reveal the borders of the tumor and minute clacifications within the tumor. Angiography may show atypically vascularized areas and thus be helpful in choosing the best site for biopsy and in making a prognosis. It might reveal, for example, unusual vascularization or penetration of tumor into blood vessels. Computerized tomography allows precise delineation of the intraosseous and extraosseous borders of the tumor, and is particularly useful in this respect in regions in which angiography has its technical limitations, such as the pelvis and the spine. The radiological assessment of a tumor or tumor-like lesion should take account of the structural changes, the site of the lesion, and the age and sex of the patient. The report should include a statement about the malignancy of the lesion. (orig.) [de

Final Technical Close out Report University Research Program in Robotics for Environmental Restoration and Waste Management

International Nuclear Information System (INIS)

James S. Tulenko; Carl Crane

2004-01-01

The report covers the 2003-04 contract period, with a retrospective of the 11 years for the contract, from 1993 to 2004. This includes personnel, technical publications and reports, plus research laboratories employed. Specific information is given in eight research areas, reporting on all technology developed and/or deployed by the University of Florida

Research in Fiber Optics: Implications for Fiber Optics in Vocational-Technical Education. Final Report 1984-85.

Science.gov (United States)

Bergen County Vocational-Technical High School, Hackensack, NJ.

This project was conducted to determine the vocational, technical, and scientific skills and knowledge needed to work with the fiber optics applications that are in all areas of technology. A research assistant was hired by the project director to collect data and develop a research base for the project. Information was gathered through a…

New strategy of the optimized nuclear medicine procedures for diagnosis and management of thyroid disorder

International Nuclear Information System (INIS)

Megahed, Y.M.; El-Haleg, M.O.; Abdel-Aziz, S.M.; Fahim, F.A.; Mahmoud, A.; Ezz-El-Arab, A.; El-Aassar, S.T.; Youssef, A.

1991-01-01

This investigation aims to find the optimal contributary RIA test for the final diagnosis of the thyroid disorder subjects. T 3 , T 4 , and TSH-RIA were performed either as a single or a combined test. However, additional tests such as T 3 -uptake, FTI-calculation, and TRH-test were performed when needed. The second part of this work deals with new TSH-MAIA kit delivered by IAEA in order to evaluate its diagnostic efficiency in comparison with the conventional TSH-RIA kit widely used in the developing countries. The obtained data revealed the following: 1. T 4 -RIA is considered to be the optimal contributary single test in the final diagnosis of all thyroid disorders. 2. T 3 + T 4 is the decisive contributary combined RIA-test in the final diagnosis of all thyroid disorders. 3. S.S. TSH-MAIA is more sensitive, specific, and simple to be performed in comparison with the TSH -RIA. Moreover, considerable minute of TSH could be detected by using S.S. TSH-MAIA which was previously considered undetectable.2 fig.2 tab

Delayed diagnosis of intermittent mesenteroaxial volvulus of the stomach by computed tomography: a case report

Directory of Open Access Journals (Sweden)

Woon Colin

2008-11-01

Full Text Available Abstract Introduction Gastric volvulus is a rare condition. Presenting acutely, mesenteroaxial gastric volvulus has characteristic symptoms and may be easily detected with upper gastrointestinal contrast studies. In contrast, subacute, intermittent cases present with intermittent vague symptoms from episodic twisting and untwisting. Imaging in these cases is only useful if performed in the symptomatic interval. Case presentation We describe a patient with a long history of intermittent chest and epigastric pain. An earlier barium meal was not diagnostic. Diagnosis was finally secured during the current admission by a combination of (1 serum investigations, (2 endoscopy, and finally (3 computed tomography. Conclusion Non-specific and misleading symptoms and signs may delay the diagnosis of intermittent, subacute volvulus. Imaging studies performed in the well interval may be non-diagnostic. Elevated creatine kinase and aldolase of a non-cardiac cause and endoscopic findings of ischaemic ulceration and difficulty in negotiating the pylorus may raise the suspicion of gastric volvulus. In this case, abdominal computed tomography with spatial reconstruction was crucial in securing the final diagnosis.

Track Circuit Fault Diagnosis Method based on Least Squares Support Vector

Science.gov (United States)

Cao, Yan; Sun, Fengru

2018-01-01

In order to improve the troubleshooting efficiency and accuracy of the track circuit, track circuit fault diagnosis method was researched. Firstly, the least squares support vector machine was applied to design the multi-fault classifier of the track circuit, and then the measured track data as training samples was used to verify the feasibility of the methods. Finally, the results based on BP neural network fault diagnosis methods and the methods used in this paper were compared. Results shows that the track fault classifier based on least squares support vector machine can effectively achieve the five track circuit fault diagnosis with less computing time.

77 FR 7489 - Small Business Size Standards: Professional, Technical, and Scientific Services

Science.gov (United States)

2012-02-10

... would (1) provide a competitive advantage to larger firms over their truly small counterparts; (2) allow... Vol. 77 Friday, No. 28 February 10, 2012 Part V Small Business Administration 13 CFR Part 121 Small Business Size Standards: Professional, Technical, and Scientific Services; Final Rule #0;#0...

Program system RALLY - for probabilistic safety analysis of large technical systems

International Nuclear Information System (INIS)

Gueldner, W.; Polke, H.; Spindler, H.; Zipf, G.

1982-03-01

This report describes the program system RALLY to compute the reliability of large and intermeshed technical systems. In addition to a short explanation of the different programs, the possible applications of the program system RALLY are demonstrated. Finally, the most important studies carried out so far on RALLY are discussed. (orig.) [de

First trimester diagnosis of parapagus diprosopus dibrachius dipus twins with cranirachischisis totalis by three-dimensional ultrasound.

Science.gov (United States)

Ülker, Kahraman; Akyer, Şahika P; Temur, İsmail; Tan, Temel; Karaca, Mehmet; Adıgüzel, Esat; Gül, Abdülaziz

2012-02-01

Parapagus (laterally fused), diprosopus (two faces), dibrachius (two upper extremities), dipus (two lower extremities) conjoined twinning is extremely rare. The coexistence of anencephaly with a contiguous spinal defect (craniorachischisis totalis) makes the present case one of the rarest of the published cases. In our case, it was difficult to make the final diagnosis by two-dimensional abdominal and vaginal ultrasound. Three-dimensional ultrasound was helpful for final diagnosis and post-abortal examination confirmed the prenatal ultrasound diagnosis. The heart, diaphragm, liver and perineum were all united. Fine dissection of the heart showed four vessels arising from the ventricles and a membranous type ventricular septal defect. © 2011 The Authors. Journal of Obstetrics and Gynaecology Research © 2011 Japan Society of Obstetrics and Gynecology.

Evaluation of different parasitological techniques in the diagnosis of canine helminthiasis

Directory of Open Access Journals (Sweden)

Marcelle Temporim Novaes

2015-12-01

Full Text Available ABSTRACT. Novaes M.T. & Martins I.V.F. [Evaluation of different parasitological techniques in the diagnosis of canine helminthiasis.] Avaliação de diferentes técnicas parasitológicas no diagnóstico de helmintoses caninas. Revista Brasileira de Medicina Veterinária, 37(Supl.1:71-76, 2015. Laboratório de Parasitologia, Hospital Veterinário, Universidade Federal do Espírito Santo, Rua Alto Universitário, s/n, Guararema, Alegre, ES 29500-000, Brasil. E-mail: marcelle_temporim@hotmail.com Were collected 100 fecal samples from dogs from August 2014 to April 2015 from the Zoonosis Control Center (CCZ of Cachoeiro de Itapemirim-ES. These were sent to the laboratory of Parasitology of the Veterinary Hospital of UFES, and analyzed in duplicate by the techniques of Kato-Katz, Hoffman, TF-Test Modified/Dog and Willis in order to evaluate the technique that present higher sensitivity, convenience and lower expenses with materials for parasitological diagnosis. Statistical analysis was performed using Fisher’s exact test and kappa the 5% significance level. Together they showed up 68 positive samples, 31, 34, 26 and 62 for technical Kato-Katz, Hoffman, TF-Test and Willis respectively. The results showed that the use of Willis technique should be adopted as the standard for egg Ancylostoma spp., since the techniques Kato-Katz, Hoffman and TF-Test showed a low sensitivity for diagnosis of this parasite, and technic of Hoffman should be used as standard for Toxocara spp. In relation to convenience and lower expenses, Willis technique, should be preferred, because the runtime and the microscope slide reading is fast, requiring only the use of a supersaturated solution.

Decomposing final energy use for heating in the residential sector in Austria

International Nuclear Information System (INIS)

Holzmann, Angela; Adensam, Heidelinde; Kratena, Kurt; Schmid, Erwin

2013-01-01

In Austria a considerable number of measures have been implemented to reduce final energy use for residential heating since the 1990s. The aim of this analysis is to investigate, why – despite these implemented measures – final energy use for heating has not decreased in the expected way. The impact of eight factors on final energy use for heating is quantified by applying the Logarithmic Mean Divisia Index (LMDI I) method. The dataset covers the sector of private households in Austria for the period from 1993 to 2009. The main findings of the analysis are: (1) while technical improvements reduce final energy use for heating significantly, rising comfort needs nearly outweigh these savings. (2) Consumer behaviour reduces calculated final energy use considerably. (3) The extent of this reduction is declining significantly in the period observed. (4) The growing share of single-family houses has increased energy demand for heating in the observed period, though a reversal of this trend is detected from 2007 onwards. (5) The impact of growing floor space per person is the major effect revealed by the analysis. (6) Weather conditions have a major impact on annual fluctuations of energy consumption. -- Highlights: •We did an Index decomposition analysis of the Austrian residential heating demand. •Eight impact factors on heating demand have been identified. •Rising comfort needs outweigh savings caused by technical improvements. •Consumer behaviour has a major impact on residential final energy use for heating. •Weather changes play a major role when analysing annual changes in energy use

The fluctuations of China’s energy intensity: Biased technical change

International Nuclear Information System (INIS)

Wang, Ce; Liao, Hua; Pan, Su-Yan; Zhao, Lu-Tao; Wei, Yi-Ming

2014-01-01

Highlights: • Biased technical change is considered in the adjusting the input–output tables. • The level of biased technical change is determined by TFP and energy efficiency. • The increase in energy intensity was mostly attributed to the structural change. • The changes in the production technology actually decreased the energy intensity. • The decomposition results are sensitive to the level of biased technical change. - Abstract: The fluctuations of China’s energy intensity have attracted the attention of many scholars, but fewer studies consider the data quality of official input–output tables. This paper conducts a decomposition model by using the Divisia method based on the input–output tables. Because of the problems with input–output tables and price deflators, we first produce constant prices to deflate the input–output tables. And then we consider different levels of biased technical change for different sectors in the adjusting the input–output table. Finally, we use RAS technique to adjust input–output matrix. Then the decomposition model is employed to empirically analyze the change of China’s energy intensity. We compare the decomposition results with and without biased technical change and do sensitive analysis on the level of biased technical change. The decomposition results are that during 2002–2007, the energy intensity of coal and electricity increased, the changes were mostly attributed to the structural change and the contribution was 594.08%, 73.88%, respectively; as for crude oil and refined oil, the energy intensity decreased, the changes were mostly attributed to the changes in the production technology and the contribution was 978.89%, 246.95%, respectively. And the results of sensitive analysis shows that 1% variation of the level of biased technical change will cause at most 0.6% change of decomposition results. Therefore, we can draw our conclusions: compared to the decomposition without biased technical

Technical approach to groundwater restoration

International Nuclear Information System (INIS)

1993-01-01

The Technical Approach to Groundwater Restoration (TAGR) provides general technical guidance to implement the groundwater restoration phase of the Uranium Mill Tailings Remedial Action (UMTRA) Project. The TAGR includes a brief overview of the surface remediation and groundwater restoration phases of the UMTRA Project and describes the regulatory requirements, the National Environmental Policy Act (NEPA) process, and regulatory compliance. A section on program strategy discusses program optimization, the role of risk assessment, the observational approach, strategies for meeting groundwater cleanup standards, and remedial action decision-making. A section on data requirements for groundwater restoration evaluates the data quality objectives (DQO) and minimum data required to implement the options and comply with the standards. A section on sits implementation explores the development of a conceptual site model, approaches to site characterization, development of remedial action alternatives, selection of the groundwater restoration method, and remedial design and implementation in the context of site-specific documentation in the site observational work plan (SOWP) and the remedial action plan (RAP). Finally, the TAGR elaborates on groundwater monitoring necessary to evaluate compliance with the groundwater cleanup standards and protection of human health and the environment, and outlines licensing procedures

78 FR 27963 - Reliability Technical Conference; Notice of Technical Conference

Science.gov (United States)

2013-05-13

... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, July 9, 2013 from 9:00 a.m. to 5:00 p.m. This... technical support for webcasts and offers the option of listening to the meeting via phone-bridge for a fee...

Do technical parameters affect the diagnostic accuracy of virtual bronchoscopy in patients with suspected airways stenosis?

International Nuclear Information System (INIS)

Jones, Catherine M.; Athanasiou, Thanos; Nair, Sujit; Aziz, Omer; Purkayastha, Sanjay; Konstantinos, Vlachos; Paraskeva, Paraskevas; Casula, Roberto; Glenville, Brian; Darzi, Ara

2005-01-01

Purpose: Virtual bronchoscopy has gained popularity over the past decade as an alternative investigation to conventional bronchoscopy in the diagnosis, grading and monitoring of airway disease. The effect of technical parameters on diagnostic outcome from virtual bronchoscopy has not been determined. This meta-analysis aims to estimate accuracy of virtual compared to conventional bronchoscopy in patients with suspected airway stenosis, and evaluate the influence of technical parameters. Materials and methods: A MEDLINE search was used to identify relevant published studies. The primary endpoint was the 'correct diagnosis' of stenotic lesions on virtual compared to conventional bronchoscopy. Secondary endpoints included the effects of the technical parameters (pitch, collimation, reconstruction interval, rendering method, and scanner type), and date of publication on the diagnostic accuracy of virtual bronchoscopy. Results: Thirteen studies containing 454 patients were identified. Meta-analysis showed good overall diagnostic performance with 85% calculated pooled sensitivity (95% CI 77-91%), 87% specificity (95% CI 81-92%) and area under the curve (AUC) of 0.947. Subgroups included collimation of 3 mm or more (AUC 0.948), pitch of 1 (AUC 0.955), surface rendering technique (AUC 0.935), and reconstruction interval of more than 1.25 mm (AUC 0.914). There was no significant difference in accuracy accounting for publication date, scanner type or any of the above variables. Weighted regression analysis confirmed none of these variables could significantly account for study heterogeneity. Conclusion: Virtual bronchoscopy performs well in the investigation of patients with suspected airway stenosis. Overall sensitivity and specificity and diagnostic odds ratio for diagnosis of airway stenosis were high. The effects of pitch, collimation, reconstruction interval, rendering technique, scanner type, and publication date on diagnostic accuracy were not significant

Use of immunoassay technologies for the diagnosis and control of foot-and-mouth disease in Southeast Asia. Proceedings of a final research co-ordination meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The IAEA and FAO, through the activities of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture and their technical co-operation programmes, support the introduction of nuclear and related techniques to improve animal disease diagnosis and surveillance in developing countries. At a workshop hosted by the Australian Centre for International Agricultural Research (ACIAR) and the Department of Livestock Development (DLD) of Thailand, in Lampang, Thailand, in September 1993, an analysis of the results of an ACIAR project on foot-and-mouth disease (FMD) as well as national reports from twelve other Asian countries clearly demonstrated that the control and eradication of FMD in Asia is both a national and regional problem (vaccination alone costs in the region US $380 million annually). It was concluded that a co-ordinated regional approach was the only realistic way forward for controlling and eventually eradicating FMD from the region. It was agreed that the OIE would lead this co-ordinated regional programme in close co-operation with FAO, ACIAR, other relevant international organizations and national governments. Results of the ACIAR Project also clearly demonstrated the immense value of ELISA based systems for the diagnosis and control of FMD within Thailand. The meeting, therefore, recommended that an essential component of a regional strategy was to have, as a minimum, ELISA tests for the detection of FMD virus and for assessing the antibody status of livestock population in each country in the region. In support of this concept, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture established a co-ordinated research project (CRP) with the primary aim of establishing and documenting appropriate mechanisms for introducing and using ELISA based technologies for FMD diagnosis and surveillance in participating countries. At the completion of this Project, the region is left with a national ELISA based diagnostic facility in

Use of immunoassay technologies for the diagnosis and control of foot-and-mouth disease in Southeast Asia. Proceedings of a final research co-ordination meeting

International Nuclear Information System (INIS)

2000-05-01

The IAEA and FAO, through the activities of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture and their technical co-operation programmes, support the introduction of nuclear and related techniques to improve animal disease diagnosis and surveillance in developing countries. At a workshop hosted by the Australian Centre for International Agricultural Research (ACIAR) and the Department of Livestock Development (DLD) of Thailand, in Lampang, Thailand, in September 1993, an analysis of the results of an ACIAR project on foot-and-mouth disease (FMD) as well as national reports from twelve other Asian countries clearly demonstrated that the control and eradication of FMD in Asia is both a national and regional problem (vaccination alone costs in the region US $380 million annually). It was concluded that a co-ordinated regional approach was the only realistic way forward for controlling and eventually eradicating FMD from the region. It was agreed that the OIE would lead this co-ordinated regional programme in close co-operation with FAO, ACIAR, other relevant international organizations and national governments. Results of the ACIAR Project also clearly demonstrated the immense value of ELISA based systems for the diagnosis and control of FMD within Thailand. The meeting, therefore, recommended that an essential component of a regional strategy was to have, as a minimum, ELISA tests for the detection of FMD virus and for assessing the antibody status of livestock population in each country in the region. In support of this concept, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture established a co-ordinated research project (CRP) with the primary aim of establishing and documenting appropriate mechanisms for introducing and using ELISA based technologies for FMD diagnosis and surveillance in participating countries. At the completion of this Project, the region is left with a national ELISA based diagnostic facility in

Rest and exercise radionuclide angiography for diagnosis in chronic ischemic heart disease

International Nuclear Information System (INIS)

Gibbons, R.J.

1991-01-01

Rest and exercise radionuclide angiography is frequently employed for the diagnosis of chest pain syndromes. Its value and limitations in this regard have been well studied, but proper utilization of the technique requires an understanding of five critical concepts: (1) Radionuclide angiography is superior to treadmill exercise testing and probably equivalent to thallium scintigraphy, although the published series did not use current methods. (2) The true specificity of radionuclide angiography is about 80%, intermediate between the early optimistic estimates and the later pessimistic ones. (3) The peak exercise ejection fraction is the preferred test parameter for diagnosis, although exercise hemodynamics, symptoms, and electrocardiographic changes should also be considered. (4) Although radionuclide angiography is clearly helpful for noninvasive diagnosis, significant numbers of patients will continue to fall in an uncertain category. (5) The proper application of the technique requires recognition of its limitations and careful attention to technical details. When properly applied, this modality can make an important contribution to clinical decision making. 58 references

European Upper Atmosphere Server DIAS - Final Conference/ Abstract

Science.gov (United States)

2007-01-10

PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) INGV - Istituto Nazionale di Geofisica e Vulcanologia (Nat Instit Geophysics, Volcanology) Via di Vigna...organised by the Istituto Nazionale di Geofisica e Vulcanologia (INGV), Rome, Italy. D6.8 Report on the Final Conference - 3 - In general, the DIAS...the Istituto Nazionale di Geofisica e Vulcanologia in Rome focused on the general overview of scientific and technical tools adopted by the DIAS

Theoretical studies of multistep processes, isospin effects in nuclear scattering, and meson and baryon interactions in nuclear physics. Final technical report, 1 September 1979-30 April 1986