ANALYSIS OF DEVONIAN BLACK SHALES IN KENTUCKY FOR POTENTIAL CARBON DIOXIDE SEQUESTRATION AND ENHANCED NATURAL GAS PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

Brandon C. Nuttall

2004-08-01

Devonian gas shales underlie approximately two-thirds of Kentucky. In the shale, natural gas is adsorbed on clay and kerogen surfaces. This is analogous to methane storage in coal beds, where CO{sub 2} is preferentially adsorbed, displacing methane. Black shales may similarly desorb methane in the presence of CO{sub 2}. Drill cuttings from the Kentucky Geological Survey Well Sample and Core Library are being sampled to collect CO{sub 2} adsorption isotherms. Sidewall core samples have been acquired to investigate CO{sub 2} displacement of methane. An elemental capture spectroscopy log has been acquired to investigate possible correlations between adsorption capacity and mineralogy. Average random vitrinite reflectance data range from 0.78 to 1.59 (upper oil to wet gas and condensate hydrocarbon maturity range). Total organic content determined from acid-washed samples ranges from 0.69 to 4.62 percent. CO{sub 2} adsorption capacities at 400 psi range from a low of 19 scf/ton in less organic-rich zones to more than 86 scf/ton in the Lower Huron Member of the shale. Initial estimates based on these data indicate a sequestration capacity of 5.3 billion tons of CO{sub 2} in the Lower Huron Member of the Ohio Shale of eastern Kentucky and as much as 28 billion tons total in the deeper and thicker parts of the Devonian shales in Kentucky. Should the black shales of Kentucky prove to be a viable geologic sink for CO{sub 2}, their extensive occurrence in Paleozoic basins across North America would make them an attractive regional target for economic CO{sub 2} storage and enhanced natural gas production.

Formation evaluation in Devonian shale through application of new core and log analysis methods

International Nuclear Information System (INIS)

Luffel, D.L.; Guidry, F.K.

1990-01-01

In the Devonian shale of the Appalachian Basin all porosity in excess of about 2.5 percent is generally occupied by free hydrocarbons, which is mostly gas, based on results of new core and log analysis methods. In this study, sponsored by the Gas Research Institute, reservoir porosities averaged about 5 percent and free gas content averaged about 2 percent by bulk volume, based on analyses on 519 feet of conventional core in four wells. In this source-rich Devonian shale, which also provides the reservoir storage, the rock everywhere appears to be at connate, or irreducible, water saturation corresponding to two or three percent of bulk volume. This became evident when applying the new core and log analysis methods, along with a new plotting method relating bulk volume of pore fluids to porosity. This plotting method has proved to be a valuable tool: it provides useful insight on the fluid distribution present in the reservoir, it provides a clear idea of porosity required to store free hydrocarbons, it leads to a method of linking formation factor to porosity, and it provides a good quality control method to monitor core and log analysis results. In the Devonian shale an important part of the formation evaluation is to determine the amount of kerogen, since this appears as hydrocarbon-filled porosity to conventional logs. In this study Total Organic Carbon and pyrolysis analyses were made on 93 core samples from four wells. Based on these data a new method was used to drive volumetric kerogen and free oil content, and kerogen was found to range up to 26 percent by volume. A good correlation was subsequently developed to derive kerogen from the uranium response of the spectral gamma ray log. Another important result of this study is the measurement of formation water salinity directly on core samples. Results on 50 measurements in the four study wells ranged from 19,000 to 220,000 ppm NaCl

ANALYSIS OF DEVONIAN BLACK SHALES IN KENTUCKY FOR POTENTIAL CARBON DIOXIDE SEQUESTRATION AND ENHANCED NATURAL GAS PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

Brandon C. Nuttall

2005-04-26

Devonian gas shales underlie approximately two-thirds of Kentucky. In the shale, natural gas is adsorbed on clay and kerogen surfaces. This is analogous to methane storage in coal beds, where CO{sub 2} is preferentially adsorbed, displacing methane. Black shales may similarly desorb methane in the presence of CO{sub 2}. Drill cuttings from the Kentucky Geological Survey Well Sample and Core Library were sampled to determine CO{sub 2} and CH{sub 4} adsorption isotherms. Sidewall core samples were acquired to investigate CO{sub 2} displacement of methane. An elemental capture spectroscopy log was acquired to investigate possible correlations between adsorption capacity and mineralogy. Average random vitrinite reflectance data range from 0.78 to 1.59 (upper oil to wet gas and condensate hydrocarbon maturity range). Total organic content determined from acid-washed samples ranges from 0.69 to 14 percent. CO{sub 2} adsorption capacities at 400 psi range from a low of 14 scf/ton in less organic-rich zones to more than 136 scf/ton. There is a direct correlation between measured total organic carbon content and the adsorptive capacity of the shale; CO{sub 2} adsorption capacity increases with increasing organic carbon content. Initial estimates based on these data indicate a sequestration capacity of 5.3 billion tons of CO{sub 2} in the Lower Huron Member of the Ohio Shale of eastern Kentucky and as much as 28 billion tons total in the deeper and thicker parts of the Devonian shales in Kentucky. Should the black shales of Kentucky prove to be a viable geologic sink for CO{sub 2}, their extensive occurrence in Paleozoic basins across North America would make them an attractive regional target for economic CO{sub 2} storage and enhanced natural gas production.

ANALYSIS OF DEVONIAN BLACK SHALES IN KENTUCKY FOR POTENTIAL CARBON DIOXIDE SEQUESTRATION AND ENHANCED NATURAL GAS PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

Brandon C. Nuttall

2005-01-28

Devonian gas shales underlie approximately two-thirds of Kentucky. In the shale, natural gas is adsorbed on clay and kerogen surfaces. This is analogous to methane storage in coal beds, where CO{sub 2} is preferentially adsorbed, displacing methane. Black shales may similarly desorb methane in the presence of CO{sub 2}. Drill cuttings from the Kentucky Geological Survey Well Sample and Core Library were sampled to determine CO{sub 2} and CH{sub 4} adsorption isotherms. Sidewall core samples were acquired to investigate CO{sub 2} displacement of methane. An elemental capture spectroscopy log was acquired to investigate possible correlations between adsorption capacity and mineralogy. Average random vitrinite reflectance data range from 0.78 to 1.59 (upper oil to wet gas and condensate hydrocarbon maturity range). Total organic content determined from acid-washed samples ranges from 0.69 to 14 percent. CO{sub 2} adsorption capacities at 400 psi range from a low of 14 scf/ton in less organic-rich zones to more than 136 scf/ton. There is a direct correlation between measured total organic carbon content and the adsorptive capacity of the shale; CO{sub 2} adsorption capacity increases with increasing organic carbon content. Initial estimates based on these data indicate a sequestration capacity of 5.3 billion tons of CO{sub 2} in the Lower Huron Member of the Ohio Shale of eastern Kentucky and as much as 28 billion tons total in the deeper and thicker parts of the Devonian shales in Kentucky. Should the black shales of Kentucky prove to be a viable geologic sink for CO{sub 2}, their extensive occurrence in Paleozoic basins across North America would make them an attractive regional target for economic CO{sub 2} storage and enhanced natural gas production.

ANALYSIS OF DEVONIAN BLACK SHALES IN KENTUCKY FOR POTENTIAL CARBON DIOXIDE SEQUESTRATION AND ENHANCED NATURAL GAS PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

Brandon C. Nuttall

2005-07-29

Devonian gas shales underlie approximately two-thirds of Kentucky. In the shale, natural gas is adsorbed on clay and kerogen surfaces. This is analogous to methane storage in coal beds, where CO{sub 2} is preferentially adsorbed, displacing methane. Black shales may similarly desorb methane in the presence of CO{sub 2}. Drill cuttings from the Kentucky Geological Survey Well Sample and Core Library were sampled to determine CO{sub 2} and CH{sub 4} adsorption isotherms. Sidewall core samples were acquired to investigate CO{sub 2} displacement of methane. An elemental capture spectroscopy log was acquired to investigate possible correlations between adsorption capacity and mineralogy. Average random vitrinite reflectance data range from 0.78 to 1.59 (upper oil to wet gas and condensate hydrocarbon maturity range). Total organic content determined from acid-washed samples ranges from 0.69 to 14 percent. CO{sub 2} adsorption capacities at 400 psi range from a low of 14 scf/ton in less organic-rich zones to more than 136 scf/ton. There is a direct correlation between measured total organic carbon content and the adsorptive capacity of the shale; CO{sub 2} adsorption capacity increases with increasing organic carbon content. Initial estimates based on these data indicate a sequestration capacity of 5.3 billion tons of CO{sub 2} in the Lower Huron Member of the Ohio Shale of eastern Kentucky and as much as 28 billion tons total in the deeper and thicker parts of the Devonian shales in Kentucky. Should the black shales of Kentucky prove to be a viable geologic sink for CO{sub 2}, their extensive occurrence in Paleozoic basins across North America would make them an attractive regional target for economic CO{sub 2} storage and enhanced natural gas production.

ANALYSIS OF DEVONIAN BLACK SHALES IN KENTUCKY FOR POTENTIAL CARBON DIOXIDE SEQUESTRATION AND ENHANCED NATURAL GAS PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

Brandon C. Nuttall

2005-01-01

Devonian gas shales underlie approximately two-thirds of Kentucky. In the shale, natural gas is adsorbed on clay and kerogen surfaces. This is analogous to methane storage in coal beds, where CO{sub 2} is preferentially adsorbed, displacing methane. Black shales may similarly desorb methane in the presence of CO{sub 2}. Drill cuttings from the Kentucky Geological Survey Well Sample and Core Library were sampled to determine CO{sub 2} and CH{sub 4} adsorption isotherms. Sidewall core samples were acquired to investigate CO{sub 2} displacement of methane. An elemental capture spectroscopy log was acquired to investigate possible correlations between adsorption capacity and mineralogy. Average random vitrinite reflectance data range from 0.78 to 1.59 (upper oil to wet gas and condensate hydrocarbon maturity range). Total organic content determined from acid-washed samples ranges from 0.69 to 14 percent. CO{sub 2} adsorption capacities at 400 psi range from a low of 14 scf/ton in less organic-rich zones to more than 136 scf/ton. Initial estimates based on these data indicate a sequestration capacity of 5.3 billion tons of CO{sub 2} in the Lower Huron Member of the Ohio Shale of eastern Kentucky and as much as 28 billion tons total in the deeper and thicker parts of the Devonian shales in Kentucky. Should the black shales of Kentucky prove to be a viable geologic sink for CO{sub 2}, their extensive occurrence in Paleozoic basins across North America would make them an attractive regional target for economic CO{sub 2} storage and enhanced natural gas production.

The ammonoids from the Three Forks Shale (Late Devonian of Montana

Directory of Open Access Journals (Sweden)

D. Korn

2006-08-01

Full Text Available The ammonoid fauna from the Late Devonian Three Forks Shale of Montana is revised. Six taxa were recognised, which belong to the genera Tornoceras, Pernoceras, Raymondiceras, Platyclymenia, Pleuroclymenia, and Carinoclymenia. The ammonoid assemblage suggests a stratigraphic position within the middle Famennian, most probably the Platyclymenia annulata Zone. The ammonoids display extreme septal crowding in intermediate as well as adult growth stages, which can be regarded as evidence for instable palaeoecological conditions during lifetime of the animals. Die Ammonoideenfauna aus dem oberdevonischen Three Forks Shale von Montana wird revidiert. Sechs Taxa werden unterschieden; sie gehören zu den Gattungen Tornoceras, Pernoceras, Raymondiceras, Platyclymenia, Pleuroclymenia und Carinoclymenia. Die Ammonoideen-Vergesellschaftung spricht für eine stratigraphische Position im mittleren Famennium, wahrscheinlich in der Platyclymenia annulata Zone. Die Ammonoideen zeigen auffällige Drängung der Septen in intermediären und adulten Wachstumsstadien, die als Hinweis auf instabile Lebensbedingungen für die Tiere gewertet werden kann. doi:10.1002/mmng.200600008

The rise of fire: Fossil charcoal in late Devonian marine shales as an indicator of expanding terrestrial ecosystems, fire, and atmospheric change

Science.gov (United States)

Rimmer, Susan M.; Hawkins, Sarah J.; Scott, Andrew C.; Cressler, Walter L.

2015-01-01

Fossil charcoal provides direct evidence for fire events that, in turn, have implications for the evolution of both terrestrial ecosystems and the atmosphere. Most of the ancient charcoal record is known from terrestrial or nearshore environments and indicates the earliest occurrences of fire in the Late Silurian. However, despite the rise in available fuel through the Devonian as vascular land plants became larger and trees and forests evolved, charcoal occurrences are very sparse until the Early Mississippian where extensive charcoal suggests well-established fire systems. We present data from the latest Devonian and Early Mississippian of North America from terrestrial and marine rocks indicating that fire became more widespread and significant at this time. This increase may be a function of rising O2 levels and the occurrence of fire itself may have contributed to this rise through positive feedback. Recent atmospheric modeling suggests an O2 low during the Middle Devonian (around 17.5%), with O2 rising steadily through the Late Devonian and Early Mississippian (to 21–22%) that allowed for widespread burning for the first time. In Devonian-Mississippian marine black shales, fossil charcoal (inertinite) steadily increases up-section suggesting the rise of widespread fire systems. There is a concomitant increase in the amount of vitrinite (preserved woody and other plant tissues) that also suggests increased sources of terrestrial organic matter. Even as end Devonian glaciation was experienced, fossil charcoal continued to be a source of organic matter being introduced into the Devonian oceans. Scanning electron and reflectance microscopy of charcoal from Late Devonian terrestrial sites indicate that the fires were moderately hot (typically 500–600 °C) and burnt mainly surface vegetation dominated by herbaceous zygopterid ferns and lycopsids, rather than being produced by forest crown fires. The occurrence and relative abundance of fossil charcoal in

Characterization and analysis of Devonian shales as related to release of gaseous hydrocarbons. Well V-7 Wetzel County, West Virginia

Energy Technology Data Exchange (ETDEWEB)

Kalyoncu, R.S.; Boyer, J.P.; Snyder, M.J.

1979-08-15

This program was initiated in September 1976, with the objective and scope of determining the relationships between the shale characteristics, hydrocarbon gas contents, and well location, and thereby provide a sound basis for (1) assessing the productive capacity of the Eastern Devonian Gas Shale deposits, and (2) guiding research, development and demonstration projects to enhance the recovery of natural gas from the shale deposits. Included in the scope of the program are a number of elemental tasks as a part of the Resource Inventory and Shale Characterization subprojects of DOE's Eastern Gas Shales Project designed to provide large quantities of support data for current and possibly future needs of the Project.

Horizontal Devonian shale well, Columbia Natural Resources, Inc. 's, Pocohontas Development Corp. Well 21747, Martin County, Kentucky

Energy Technology Data Exchange (ETDEWEB)

Koziar, G.; Ahmad, M.M.; Friend, L.L.; Friend, M.L.; Rothman, E.M.; Stollar, R.L. (Columbia Gas System Service Corp., Columbus, OH (United States))

1991-05-01

Columbia Gas and the United States Department of Energy (DOE) have successfully completed field work on a horizontally drilled Devonian shale well located in Martin County, Kentucky. The objective of this cofunded project is to assess the effectiveness and economic feasibility of applying horizontal drilling and hydraulically fracturing stimulation techniques to enhance the extraction of natural gas from the Devonian shale. The well is comprised of three segments: a conventional vertical section, an angle build section and a horizontal section. The well reached a measured depth (MD) of 6263 feet, 3810 feet true vertical depth (TVD), with a horizontal displacement of 2812 feet achieved in the desired direction of N10{degrees}W. Both air and foam were used as drilling fluids. The vertical, lateral and tangent sections were drilled using conventional rotary drilling methods. Downhole motors were used to build angle. A total combined final open flow of 3.1 MMcfd was measured from all zones. Total well expenditures are approximately $1,460,000. Of this amount, $700,000 is directly related to the research and learning curve experience aspects. It is projected that the same horizontal well could be drilled with existing technology for $700,000. If advanced can be made in MWD systems for air drilling environments, wells of this type could be drilled routinely for $500,000. It appears that application of horizontal drilling will result in at least acceleration of gas production and possibly the addition of recoverable reserves from the Devonian shale. Production data, necessary to validate this statement, are also required to determine the economics. As we gain experience and technology advances, cost reductions will occur; this will result in economic improvement.

Horizontal Devonian shale well, Columbia Natural Resources, Inc.`s, Pocohontas Development Corp. Well 21747, Martin County, Kentucky. Final report

Energy Technology Data Exchange (ETDEWEB)

Koziar, G.; Ahmad, M.M.; Friend, L.L.; Friend, M.L.; Rothman, E.M.; Stollar, R.L. [Columbia Gas System Service Corp., Columbus, OH (United States)

1991-05-01

Columbia Gas and the United States Department of Energy (DOE) have successfully completed field work on a horizontally drilled Devonian shale well located in Martin County, Kentucky. The objective of this cofunded project is to assess the effectiveness and economic feasibility of applying horizontal drilling and hydraulically fracturing stimulation techniques to enhance the extraction of natural gas from the Devonian shale. The well is comprised of three segments: a conventional vertical section, an angle build section and a horizontal section. The well reached a measured depth (MD) of 6263 feet, 3810 feet true vertical depth (TVD), with a horizontal displacement of 2812 feet achieved in the desired direction of N10{degrees}W. Both air and foam were used as drilling fluids. The vertical, lateral and tangent sections were drilled using conventional rotary drilling methods. Downhole motors were used to build angle. A total combined final open flow of 3.1 MMcfd was measured from all zones. Total well expenditures are approximately $1,460,000. Of this amount, $700,000 is directly related to the research and learning curve experience aspects. It is projected that the same horizontal well could be drilled with existing technology for $700,000. If advanced can be made in MWD systems for air drilling environments, wells of this type could be drilled routinely for $500,000. It appears that application of horizontal drilling will result in at least acceleration of gas production and possibly the addition of recoverable reserves from the Devonian shale. Production data, necessary to validate this statement, are also required to determine the economics. As we gain experience and technology advances, cost reductions will occur; this will result in economic improvement.

Regional geological assessment of the Devonian-Mississippian shale sequence of the Appalachian, Illinois, and Michigan basins relative to potential storage/disposal of radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Lomenick, T.F.; Gonzales, S.; Johnson, K.S.; Byerly, D.

1983-01-01

The thick and regionally extensive sequence of shales and associated clastic sedimentary rocks of Late Devonian and Early Mississippian age has been considered among the nonsalt geologies for deep subsurface containment of high-level radioactive wastes. This report examines some of the regional and basin-specific characteristics of the black and associated nonblack shales of this sequence within the Appalachian, Illinois, and Michigan basins of the north-central and eastern United States. Principal areas where the thickness and depth of this shale sequence are sufficient to warrant further evaluation are identified, but no attempt is made to identify specific storage/disposal sites. Also identified are other areas with less promise for further study because of known potential conflicts such as geologic-hydrologic factors, competing subsurface priorities involving mineral resources and groundwater, or other parameters. Data have been compiled for each basin in an effort to indicate thickness, distribution, and depth relationships for the entire shale sequence as well as individual shale units in the sequence. Included as parts of this geologic assessment are isopach, depth information, structure contour, tectonic elements, and energy-resource maps covering the three basins. Summary evaluations are given for each basin as well as an overall general evaluation of the waste storage/disposal potential of the Devonian-Mississippian shale sequence,including recommendations for future studies to more fully characterize the shale sequence for that purpose. Based on data compiled in this cursory investigation, certain rock units have reasonable promise for radioactive waste storage/disposal and do warrant additional study.

Regional geological assessment of the Devonian-Mississippian shale sequence of the Appalachian, Illinois, and Michigan basins relative to potential storage/disposal of radioactive wastes

International Nuclear Information System (INIS)

Lomenick, T.F.; Gonzales, S.; Johnson, K.S.; Byerly, D.

1983-01-01

The thick and regionally extensive sequence of shales and associated clastic sedimentary rocks of Late Devonian and Early Mississippian age has been considered among the nonsalt geologies for deep subsurface containment of high-level radioactive wastes. This report examines some of the regional and basin-specific characteristics of the black and associated nonblack shales of this sequence within the Appalachian, Illinois, and Michigan basins of the north-central and eastern United States. Principal areas where the thickness and depth of this shale sequence are sufficient to warrant further evaluation are identified, but no attempt is made to identify specific storage/disposal sites. Also identified are other areas with less promise for further study because of known potential conflicts such as geologic-hydrologic factors, competing subsurface priorities involving mineral resources and groundwater, or other parameters. Data have been compiled for each basin in an effort to indicate thickness, distribution, and depth relationships for the entire shale sequence as well as individual shale units in the sequence. Included as parts of this geologic assessment are isopach, depth information, structure contour, tectonic elements, and energy-resource maps covering the three basins. Summary evaluations are given for each basin as well as an overall general evaluation of the waste storage/disposal potential of the Devonian-Mississippian shale sequence,including recommendations for future studies to more fully characterize the shale sequence for that purpose. Based on data compiled in this cursory investigation, certain rock units have reasonable promise for radioactive waste storage/disposal and do warrant additional study

The Frasnian-Famennian boundary (Upper Devonian) in black shale sequences: US Southern Midcontinent, Illinois Basin, and northern Appalachian Basin

Energy Technology Data Exchange (ETDEWEB)

Over, D.J. (State Univ. of New York, Geneseo, NY (United States). Dept. of Geological Sciences)

1994-04-01

The Frasnian-Famennian (F/F) boundary in the Woodford Shale of the US southern Midcontinent, Sweetland Creek Shale of the Illinois Basin, and the Hanover Shale of the northern Appalachian Basin is recognized to a discrete horizon. In each locality the boundary is marked by evidence of a disconformity: phosphate nodules, concentration of conodonts, or coated and corroded grains. The Woodford Shale consists of finely laminated pyritic organic-rich shale containing interbeds of greenish shale and chert. The F/F boundary horizon is marked by a concentration of conodonts and phosphatic nodules. The boundary lag horizon contains Pa. linguliformis, Pa. subperlobtata, Pa. delicatula delicatula, and Pa. triangularis. Underlying laminations contain Ancyrognathus ubiquitus and Pa. triangularis indicating that the disconformity is within the uppermost MN Zone 13 or Lower triangularis Zone. The upper portion of the Type Sweetland Creek Shale consists of dark organic-rich shales. The F/F boundary is located within an interval containing three green shale interbeds. Palmatolepis triangularis in the absence of Frasnian species first occurs in the middle green shale. In the thick Upper Devonian clastic sequence of the northern Appalachian Basin the F/F boundary is within an interval of interbedded pyritic green and organic-rich silty shales of the Hanover Shale. At Irish Gulf strata containing Pa. triangularis overlie finely laminated dark shales containing Pa. bogartensis, Pa. triangularis, Pa. winchell, Ancyrodella curvata, and Icriodus alternatus. The conodont fauna transition is below a conodont-rich laminae containing a Famennian fauna that marks the boundary horizon.

The hyper-enrichment of V and Zn in black shales of the Late Devonian-Early Mississippian Bakken Formation (USA)

Science.gov (United States)

Scott, Clinton T.; Slack, John F.; Kelley, Karen Duttweiler

2017-01-01

Black shales of the Late Devonian to Early Mississippian Bakken Formation are characterized by high concentrations of organic carbon and the hyper-enrichment (> 500 to 1000s of mg/kg) of V and Zn. Deposition of black shales resulted from shallow seafloor depths that promoted rapid development of euxinic conditions. Vanadium hyper-enrichments, which are unknown in modern environments, are likely the result of very high levels of dissolved H2S (~ 10 mM) in bottom waters or sediments. Because modern hyper-enrichments of Zn are documented only in Framvaren Fjord (Norway), it is likely that the biogeochemical trigger responsible for Zn hyper-enrichment in Framvaren Fjord was also present in the Bakken basin. With Framvaren Fjord as an analogue, we propose a causal link between the activity of phototrophic sulfide oxidizing bacteria, related to the development of photic-zone euxinia, and the hyper-enrichment of Zn in black shales of the Bakken Formation.

Marcellus shale gas potential in the southern tier of New York

Energy Technology Data Exchange (ETDEWEB)

Faraj, B. [Talisman Energy Inc., Calgary, AB (Canada); Duggan, J. [Hunt Oil Canada, Calgary, AB (Canada)

2008-07-01

Marcellus shale is a significant, underexplored, shale gas target in the Appalachian Basin. Gas-in-place estimates in the Marcellus shale range from 200 to 100 billion cubic feet (bcf). The Devonian shales have favorable attributes such as high total organic content (TOC), high gas content, favorable mineralogy and over-pressured. Land owned by Fortuna Energy in the northern Appalachian Basin may contain significant shale gas with unrisked gas-in-place in excess of 10 trillion cubic feet. Unlocking the true shale gas potential requires innovative drilling and completion techniques. This presentation discussed Marcellus shale gas potential in the southern tier and a test program being conducted by Fortuna to test the potential. Several photographs were shown, including Taughannock Falls, Finger Lakes and the Ithaca Shale, Sherburne Sandstone, and Geneseo Shale; two orthogonal fracture sets in the Upper Devonian Geneseo Shale; and two orthogonal fracture sets in the Upper Devonian Rocks, near Corning, New York. Figures that were presented included the supercontinent Pangaea in the early Triassic; undiscovered gas resources in the Appalachian Basin; stratigraphy; and total gas production in New York since 1998. Fortuna's work is ongoing in the northern Appalachian Basin. tabs., figs.

On the origin of a phosphate enriched interval in the Chattanooga Shale (Upper Devonian) of Tennessee-A combined sedimentologic, petrographic, and geochemical study

Science.gov (United States)

Li, Yifan; Schieber, Juergen

2015-11-01

The Devonian Chattanooga Shale contains an uppermost black shale interval with dispersed phosphate nodules. This interval extends from Tennessee to correlative strata in Kentucky, Indiana, and Ohio and represents a significant period of marine phosphate fixation during the Late Devonian of North America. It overlies black shales that lack phosphate nodules but otherwise look very similar in outcrop. The purpose of this study is to examine what sets these two shales apart and what this difference tells us about the sedimentary history of the uppermost Chattanooga Shale. In thin section, the lower black shales (PBS) show pyrite enriched laminae and compositional banding. The overlying phosphatic black shales (PhBS) are characterized by phosbioclasts, have a general banded to homogenized texture with reworked layers, and show well defined horizons of phosphate nodules that are reworked and transported. In the PhBS, up to 8000 particles of P-debris per cm2 occur in reworked beds, whereas the background black shale shows between 37-88 particles per cm2. In the PBS, the shale matrix contains between 8-16 phosphatic particles per cm2. The shale matrix in the PhBS contains 5.6% inertinite, whereas just 1% inertinite occurs in the PBS. The shale matrix in both units is characterized by flat REE patterns (shale-normalized), whereas Phosbioclast-rich layers in the PhBS show high concentrations of REEs and enrichment of MREEs. Negative Ce-anomalies are common to all samples, but are best developed in association with Phosbioclasts. Redox-sensitive elements (Co, U, Mo) are more strongly enriched in the PBS when compared to the PhBS. Trace elements associated with organic matter (Cu, Zn, Cd, Ni) show an inverse trend of enrichment. Deposited atop a sequence boundary that separates the two shale units, the PhBS unit represents a transgressive systems tract and probably was deposited in shallower water than the underlying PBS interval. The higher phosphate content in the PhBS is

Sedimentology and facies analysis of Devonian Rocks, southern district of Mackenzie, North West Territories, Canada

NARCIS (Netherlands)

Meijer Drees, N.C.

1989-01-01

The Devonian rock succession in the southern part of the District of Mackenzie consists of interbedded evaporites and carbonates, fossiliferous carbonates and shales. Inthe study areathe Devonian succession unconformably overlies LowerPaleozoic orPrecambrian strata and thins in a northeastward

Upper Paleozoic Marine Shale Characteristics and Exploration Prospects in the Northwestern Guizhong Depression, South China

Science.gov (United States)

Zhu, Zhenhong; Yao, Genshun; Lou, Zhanghua; Jin, Aimin; Zhu, Rong; Jin, Chong; Chen, Chao

2018-05-01

Multiple sets of organic-rich shales developed in the Upper Paleozoic of the northwestern Guizhong Depression in South China. However, the exploration of these shales is presently at a relatively immature stage. The Upper Paleozoic shales in the northwestern Guizhong Depression, including the Middle Devonian Luofu shale, the Nabiao shale, and the Lower Carboniferous Yanguan shale, were investigated in this study. Mineral composition analysis, organic matter analysis (including total organic carbon (TOC) content, maceral of kerogen and the vitrinite reflection (Ro)), pore characteristic analysis (including porosity and permeability, pore type identification by SEM, and pore size distribution by nitrogen sorption), methane isothermal sorption test were conducted, and the distribution and thickness of the shales were determined, Then the characteristics of the two target shales were illustrated and compared. The results show that the Upper Paleozoic shales have favorable organic matter conditions (mainly moderate to high TOC content, type I and II1 kerogen and high to over maturity), good fracability potential (brittleness index (BI) > 40%), multiple pore types, stable distribution and effective thickness, and good methane sorption capacity. Therefore, the Upper Paleozoic shales in the northern Guizhong Depression have good shale gas potential and exploration prospects. Moreover, the average TOC content, average BI, thickness of the organic-rich shale (TOC > 2.0 wt%) and the shale gas resources of the Middle Devonian shales are better than those of the Lower Carboniferous shale. The Middle Devonian shales have better shale gas potential and exploration prospects than the Lower Carboniferous shales.

Geochemical constraints on the origin and volume of gas in the New Albany Shale (Devonian-Mississippian), eastern Illinois Basin

Science.gov (United States)

Strapoc, D.; Mastalerz, Maria; Schimmelmann, A.; Drobniak, A.; Hasenmueller, N.R.

2010-01-01

This study involved analyses of kerogen petrography, gas desorption, geochemistry, microporosity, and mesoporosity of the New Albany Shale (Devonian-Mississippian) in the eastern part of the Illinois Basin. Specifically, detailed core analysis from two locations, one in Owen County, Indiana, and one in Pike County, Indiana, has been conducted. The gas content in the locations studied was primarily dependent on total organic carbon content and the micropore volume of the shales. Gas origin was assessed using stable isotope geochemistry. Measured and modeled vitrinite reflectance values were compared. Depth of burial and formation water salinity dictated different dominant origins of the gas in place in the two locations studied in detail. The shallower Owen County location (415-433 m [1362-1421 ft] deep) contained significant additions of microbial methane, whereas the Pike County location (832-860 m [2730-2822 ft] deep) was characterized exclusively by thermogenic gas. Despite differences in the gas origin, the total gas in both locations was similar, reaching up to 2.1 cm3/g (66 scf/ton). Lower thermogenic gas content in the shallower location (lower maturity and higher loss of gas related to uplift and leakage via relaxed fractures) was compensated for by the additional generation of microbial methane, which was stimulated by an influx of glacial melt water, inducing brine dilution and microbial inoculation. The characteristics of the shale of the Maquoketa Group (Ordovician) in the Pike County location are briefly discussed to provide a comparison to the New Albany Shale. Copyright ??2010. The American Association of Petroleum Geologists. All rights reserved.

Terrestrial P and Reactive N and Marine Productivity in the Late Devonian Appalachian Basin

Science.gov (United States)

Tuite, M. L.; Macko, S. A.

2009-12-01

A causal link between the Late Devonian emergence of forest ecosystems and episodic black shale deposition has been proposed by several authors. Most attribute increases in epicontinental basin productivity to elevated rates of terrestrial phosphorus weathering facilitated by the co-evolution of root systems and soils. Two reasons to suspect that an increase in the P weathering flux was not the primary cause of organic-rich shale deposition are as follows. First, most Late Devonian black shales were deposited during sea level transgressions, periods when riverine fluxes of sediment and mineral nutrients such as P to marine basins were diminished. Second, Late Devonian forests were restricted to warm, moist lowlands where P was sequestered in soils as inorganic, occluded forms. However, the export flux of reactive N from these forests to adjacent epeiric seas by riverine and atmospheric deposition was enhanced by the warm, wet climate and expanding areal extent of forests. Abundant terrestrial reactive N primed the marine eutrophication pump by extending the residence time of P in the photic zone, permitting extensive growth of primary biomass. The consequent flux of organic matter to the sea floor created anoxic bottom waters that, in turn, allowed for the remobilization of P into the water column. Based on abundance and isotopic analyses of organic and inorganic C, N, P, and S from terrestrial and marine environments within and adjacent to the Late Devonian Appalachian Basin, this latter scenario is supported.

Devonian sand injections and volcanism in the Murzuq Basin (south-west Libya)

DEFF Research Database (Denmark)

Moreau, Julien; Ghienne, Jean-Francois

system is original by its interaction with volcanism and its situation in an epicontinental intracratonic basin. The sand injections form a seal-bypass system between the Ordovician-Cambrian reservoirs and the Lower Devonian sandstones, breaching through the Silurian shale seal (and source rock...

A review of the organic geochemistry of shales

International Nuclear Information System (INIS)

Ho, P.C.; Meyer, R.E.

1987-06-01

Shale formations have been suggested as a potential site for a high level nuclear waste repository. As a first step in the study of the possible interaction of nuclides with the organic components of the shales, literature on the identification of organic compounds from various shales of the continent of the United States has been reviewed. The Green River shale of the Cenozoic era is the most studied shale followed by the Pierre shale of the Mesozoic era and the Devonian black shale of the Paleozoic era. Organic compounds that have been identified from these shales are hydrocarbons, fatty acids, fatty alcohols, steranes, terpanes, carotenes, carbohydrates, amino acids, and porphyrins. However, these organic compounds constitute only a small fraction of the organics in shales and the majority of the organic compounds in shales are still unidentified

Analysis of the structural parameters that influence gas production from the Devonian shale. Annual progress report, 1979-1980. Volume II. Data repository and reports published during fiscal year 1979-1980: regional structure, surface structure, surface fractures, hydrology

Energy Technology Data Exchange (ETDEWEB)

Negus-De Wys, J.; Dixon, J. M.; Evans, M. A.; Lee, K. D.; Ruotsala, J. E.; Wilson, T. H.; Williams, R. T.

1980-10-01

This volume comprises appendices giving regional structure data, surface structure data, surface fracture data, and hydrology data. The fracture data covers oriented Devonian shale cores from West Virginia, Ohio, Virginia, Pennsylvania, and Kentucky. The subsurface structure of the Eastern Kentucky gas field is also covered. (DLC)

A review of the organic geochemistry of shales and possible interactions between the organic matter of shales and radionuclides

International Nuclear Information System (INIS)

Ho, P.C.

1990-01-01

Shale formations have been suggested as potential host rocks for high level nuclear waste repositories. Several studies have demonstrated the interactions of nuclides with organic compounds found in shales. In order to understand the possibility of interaction between organic components of shales and trace elements, literature on the identification of organic compounds from various shales of the continental United States and evidences of interactions have been reviewed first. The Green River Formation of the Cenozoic era is the most studied shale followed by the Pierre Shale of the Mesozoic era and the Devonian Black Shale of the Paleozoic era. Organic compounds that have been identified from these shales are mainly hydrocarbons and carboxylates along with small amounts of other compounds. These organic compounds, however, constitute only a small fraction of the organic matter in shales; the majority of the organic compounds in shales are still unidentified. Interaction between organics and trace elements are found mostly due to the formation of complexes between carboxylates of shales and the elements. (orig.)

Silurian and Devonian source rocks and crude oils from the western part of Libya: Organic geochemistry, palynology and carbon stratigraphy

NARCIS (Netherlands)

Elkelani, Mohamed M.A.

2015-01-01

The Early Silurian “hot” shales and Late Devonian black shales are major regional oil and gas source rocks in North Africa. Their deposition probably played a major role in global carbon cycling in general because of the large areas of the ocean affected. Comparing the Libyan δ13C record with

Factors controlling Li concentration and isotopic composition in formation waters and host rocks of Marcellus Shale, Appalachian Basin

Science.gov (United States)

Phan, Thai T.; Capo, Rosemary C; Stewart, Brian W.; Macpherson, Gwen; Rowan, Elisabeth L.; Hammack, Richard W.

2015-01-01

In this study, water and whole rock samples from hydraulically fractured wells in the Marcellus Shale (Middle Devonian), and water from conventional wells producing from Upper Devonian sandstones were analyzed for lithium concentrations and isotope ratios (δ7Li). The distribution of lithium concentrations in different mineral groups was determined using sequential extraction. Structurally bound Li, predominantly in clays, accounted for 75-91 wt. % of total Li, whereas exchangeable sites and carbonate cement contain negligible Li (shale in Greene Co., Pennsylvania, and Tioga Co., New York, ranged from -2.3 to + 4.3‰, similar to values reported for other shales in the literature. The δ7Li values in shale rocks with stratigraphic depth record progressive weathering of the source region; the most weathered and clay-rich strata with isotopically light Li are found closest to the top of the stratigraphic section. Diagenetic illite-smectite transition could also have partially affected the bulk Li content and isotope ratios of the Marcellus Shale.

Shale engineering application: the MAL-145 project in West Virginia

Energy Technology Data Exchange (ETDEWEB)

Vassilellis, George D.; Li, Charles; Bust, Vivian K. [Gaffney, Cline and Associates (United States); Moos, Daniel; Cade, Randal [Baker Hughes Inc (United States)

2011-07-01

With the depletion of conventional fossil fuels and the rising energy demand, oil shale and shale gas are becoming an important component of the oil and gas markets in North America. The aim of this paper is to present a novel methodology for predicting production in shale and tight formations. This method, known as the shale engineering approach and modeling, provides reservoir simulations based on modeling the propagation of the simulated rock volume. This technique was applied to an Upper Devonian shale formation in West Virginia, United States, and was compared to available data such as production logs and downhole microseismic data. Results showed a good match between the shale engineering approach data and early well performance. This paper presented a new reservoir simulation methodology which is successful in forecasting production and which can also be used for field development design and optimization.

Petrology of the Devonian gas-bearing shale along Lake Erie helps explain gas shows

Energy Technology Data Exchange (ETDEWEB)

Broadhead, R.F.; Potter, P.E.

1980-11-01

Comprehensive petrologic study of 136 thin sections of the Ohio Shale along Lake Erie, when combined with detailed stratigraphic study, helps explain the occurrence of its gas shows, most of which occur in the silty, greenish-gray, organic poor Chagrin Shale and Three Lick Bed. Both have thicker siltstone laminae and more siltstone beds than other members of the Ohio Shale and both units also contain more clayshales. The source of the gas in the Chagrin Shale and Three Lick Bed of the Ohio Shale is believed to be the bituminous-rich shales of the middle and lower parts of the underlying Huron Member of the Ohio Shale. Eleven petrographic types were recognized and extended descriptions are provided of the major ones - claystones, clayshales, mudshales, and bituminous shales plus laminated and unlaminated siltstones and very minor marlstones and sandstones. In addition three major types of lamination were identified and studied. Thirty-two shale samples were analyzed for organic carbon, whole rock hydrogen and whole rock nitrogen with a Perkin-Elmer 240 Elemental Analyzer and provided the data base for source rock evaluation of the Ohio Shale.

Germanium and uranium in coalified wood from upper Devonian black shale

Energy Technology Data Exchange (ETDEWEB)

Breger, I A; Schopf, J M

1955-02-01

Spectrographic analyses were performed on carbonaceous material and shale samples from the Chattanooga shale in Tennessee and the Cleveland member of the Ohio shale in Ohio with particular emphasis on U and Ge. Semiquantitative analyses for 29 elements (Fe, Si, Ge, Al, Ca, V, Ni, U, Mg, Cu, Ti, Cr, Mo, Na, Sr, B, Y, Pb, Ba, Co, Sn, Zr, Mn, Zn, Yb, Ga, Sc, Be) were performed on both ash specimens and whole sample. The analyses showed unusually high percentages of Ge (1 to 5%) U (0.1 to 1%), V (1 to 5%), and Ni (0.1 to 1%) in the ash of coal from the Chattanooga and Ohio shales. Quantitative chemical analysis for U, Ge, V, and Ni in the whole coal and ash were done to check the results of the semiquantitative analyses. Ash content from the proximate analyses indicated that the coal samples tested were similar to vitrain in ash percentage. Because of the unusually high percentages of U and Ge and the low ash of the coals tested, the author felt that the U and Ge might be associated wire also observed with lower radiation doses (200 and 400 rad).

EARLY ORDOVICIAN AND DEVONIAN CONODONTS FROM THE WESTERN KARAKORAM AND HINDU KUSH, NORTHERNMOST PAKISTAN

Directory of Open Access Journals (Sweden)

JOHN A. TALENT

1999-07-01

Full Text Available Extensive tracts of Devonian and older sedimentary and igneous units occur within the axial region of the western Karakoram Block of northernmost Pakistan over a distance in excess of 200 km between the the headwaters of the Karambar valley in northwestern Gilgit Agency to southwestern Chitral. Conodont data indicate that the oldest sedimentary unit so far discriminated within this belt, the Yarkhun Formation, includes horizons of Ordovician (Arenig age, consistent with an earlier-presented acritarch-based Arenig age for part of the same unit. Conodont data from the "Lun Shales", a stratigraphic potpourri with little-known Silurian and Devonian tracts, demonstrate the presence of Early Devonian (early Emsian horizons. The Shogrâm Formation, widely distributed through the region, spans an appreciable interval of the Middle and Late Devonian mid-Givetian through until at least early Famennian. A major lacuna in sedimentation may be present, represented by all or most of the earlier half of Frasnian time. A biostratigraphically and possibly biogeographically important new species, Icriodus homeomorphus, is described; it is encountered in horizons of early Famennian age (Late triangularis Zone to ?Early crepida Zone. 

Factors controlling Li concentration and isotopic composition in formation waters and host rocks of Marcellus Shale, Appalachian Basin

Science.gov (United States)

Phan, Thai T.; Capo, Rosemary C; Stewart, Brian W.; Macpherson, Gwen; Rowan, Elisabeth L.; Hammack, Richard W.

2015-01-01

In this study, water and whole rock samples from hydraulically fractured wells in the Marcellus Shale (Middle Devonian), and water from conventional wells producing from Upper Devonian sandstones were analyzed for lithium concentrations and isotope ratios (δ7Li). The distribution of lithium concentrations in different mineral groups was determined using sequential extraction. Structurally bound Li, predominantly in clays, accounted for 75-91 wt. % of total Li, whereas exchangeable sites and carbonate cement contain negligible Li (< 3%). Up to 20% of the Li is present in the oxidizable fraction (organic matter and sulfides). The δ7Li values for whole rock shale in Greene Co., Pennsylvania, and Tioga Co., New York, ranged from -2.3 to + 4.3‰, similar to values reported for other shales in the literature. The δ7Li values in shale rocks with stratigraphic depth record progressive weathering of the source region; the most weathered and clay-rich strata with isotopically light Li are found closest to the top of the stratigraphic section. Diagenetic illite-smectite transition could also have partially affected the bulk Li content and isotope ratios of the Marcellus Shale.

Petroleum data for the pre-mid-Devonian basal clastics play, southern Mackenzie Valley

Energy Technology Data Exchange (ETDEWEB)

Lemieux, Y. [Natural Resources Canada, Yellowknife, NT (Canada). Geological Survey of Canada; Gal, L.P. [Northwest Territories Geoscience Office, Yellowknife, NT (Canada)

2008-07-01

This document presented petroleum data from the Mackenzie Corridor exploration area in the Northwest Territories. Both quantitative and qualitative geoscience data was compiled as part of a project under the Secure Canadian Energy Supply program of the Geological Survey of Canada. Three separate reservoir facies have been identified within the study area for their attributes relevant to petroleum exploration. This document defined and described the pre-mid-Devonian basal clastics play in the southern Great Slave Plains region where potential Lower Paleozoic source rocks include organic-rich beds of the Mirage Point and Chinchaga Formations, and regionally widespread, Middle to lower Upper Devonian shale. The play is analogous to the oil producing Middle Devonian clastic plays onlapping the Peace River Arch in northwestern Alberta. The seals, migration and trap styles for the reservoirs were discussed. Exploration risks include a thin and discontinuous reservoir with poor porosity; isolation from potential source beds; inadequate reservoir seals; and timing of hydrocarbon migration with respect to trap development. The petroleum play information was based on very few well penetrations. As such, the pre-mid-Devonian basal clastics play is considered to be a conceptual play that has not yet been adequately explored. 40 refs., 3 tabs., 12 figs.

The influence of hurricanes upon the quiet depositional conditions in the Lower Emsian La Vid shales of Colle (NW Spain)

NARCIS (Netherlands)

Stel, Jan H.

1976-01-01

The author supposes that the fossil content of thin carbonate units in the Upper La Vid shales (Lower Devonian) of Colle was influenced by heavy storms like hurricanes. Apart from microplankton (Cramer, 1964) no fossils are found in the shales. Together with the very well developed fissility of the

Gas storage in the Upper Devonian-Lower Mississippian Woodford Shale, Arbuckle Mountains, Oklahoma: how much of a role do the cherts play?

Science.gov (United States)

Fishman, Neil S.; Ellis, Geoffrey S.; Paxton, Stanley T.; Abbott, Marvin M.; Boehlke, Adam

2010-01-01

How gas is stored in shale-gas systems is a critical element in characterizing these potentially prolific, low-porosity/permeability reservoirs. An integrated mineralogic, geochemical, and porosity/permeability study is of the Upper Devonian-Lower Mississippian Woodford Shale, Arbuckle Mountains, southern Oklahoma, at locations previously described through detailed stratigraphic and spectral gamma surveys, was undertaken to provide insights into possible mechanisms by which natural gas might be stored in Woodford reservoirs in the adjacent Anadarko Basin. The outcrops in the Arbuckle Mountains are an ideal location to study the Woodford because here the formation is immature or marginally mature for oil generation (Comer and Hinch, 1987; Lewan, 1987), so deep burial and thermal maturation are much less pronounced than is the case for the Woodford in the basin, and as such the samples we studied are not overprinted by possible alterations resulting from deep burial and heating. Rock types studied in the Woodford Shale are broadly divided into chert (n = 8) and mudstone (n = 10) lithologies that display different characteristics from the outcrop to thin section scales. Woodford cherts, based on quantitative X-ray diffraction (XRD), contain >85 weight (wt) % quartz, green algae). Quartz in mudstones is both detrital and authigenic, with unequivocal authigenic quartz occurring as monocrystalline “grains” that can partly or even completely infill Tasmanites; as in the case of the cherts, authigenic quartz in mudstones must have precipitated soon after deposition before significant burial and collapse of the soft, delicate Tasmanites cysts. MICP analyses (at 50% Hg saturation) reveal that, with one exception, mudstones have (1) porosities ranging from 1.97-6.31%, (2) low calculated permeabilities (0.011-0.089 D), and (3) small mean pore apertures (6.2-17.8 nm). Porosity in the mudstones occurs as (1) “slots” between clay mineral grains or plates, (2) micropores

Assessment of Factors Influencing Effective CO₂ Storage Capacity and Injectivity in Eastern Gas Shales

Energy Technology Data Exchange (ETDEWEB)

Godec, Michael [Advanced Resources International, Inc., Arlington, VA (United States)

2013-06-30

Building upon advances in technology, production of natural gas from organic-rich shales is rapidly developing as a major hydrocarbon supply option in North America and around the world. The same technology advances that have facilitated this revolution - dense well spacing, horizontal drilling, and hydraulic fracturing - may help to facilitate enhanced gas recovery (EGR) and carbon dioxide (CO₂) storage in these formations. The potential storage of CO₂ in shales is attracting increasing interest, especially in Appalachian Basin states that have extensive shale deposits, but limited CO₂ storage capacity in conventional reservoirs. The goal of this cooperative research project was to build upon previous and on-going work to assess key factors that could influence effective EGR, CO₂ storage capacity, and injectivity in selected Eastern gas shales, including the Devonian Marcellus Shale, the Devonian Ohio Shale, the Ordovician Utica and Point Pleasant shale and equivalent formations, and the late Devonian-age Antrim Shale. The project had the following objectives: (1) Analyze and synthesize geologic information and reservoir data through collaboration with selected State geological surveys, universities, and oil and gas operators; (2) improve reservoir models to perform reservoir simulations to better understand the shale characteristics that impact EGR, storage capacity and CO₂ injectivity in the targeted shales; (3) Analyze results of a targeted, highly monitored, small-scale CO₂ injection test and incorporate into ongoing characterization and simulation work; (4) Test and model a smart particle early warning concept that can potentially be used to inject water with uniquely labeled particles before the start of CO₂ injection; (5) Identify and evaluate potential constraints to economic CO₂ storage in gas shales, and propose development approaches that overcome these constraints

Geothermometry methods for determining the thermal history of shales

International Nuclear Information System (INIS)

Weaver, C.E.

1977-01-01

When clays and muds are deposited, the clay mineral suite is usually not an equilibrium assemblage. With time and increased depth of burial and temperature, the clay mineral suite undergoes continuous chemical and mineral changes as it adjusts to increasingly higher temperatures. Significant changes are observed at temperatures as low as 50 0 C and continue to 400 0 C (beginning of metamorphism) and above. Once these clay-rich rocks are exposed to elevated temperatures and then later uplifted to areas of lower temperature, no significant changes occur unless the rock is exposed to weathering or to temperatures higher than that to which they have been exposed previously. An initial objective is to develop the ability to determine the mineral, chemical, and textural changes which are produced in shales by increased temperature. This will allow prediction of the diagenetic changes that occur in shales when they are exposed to the heat generated by radioactive waste. A second objective is to develop the ability to determine the maximum temperature to which a shale has been exposed. Once a shale has been exposed to temperatures of 200 to 400 0 C for thousands of years, an equilibrium assemblage is obtained which persists after the shale is elevated to near surface conditions and is only altered if the shale is exposed to temperatures higher than those of the maximum to which the shale was originally exposed. A proposal is made to select for initial study a thick Paleozoic shale, probably of Cambro-Ordovician or Devonian age, in the Appalachian region. A shale sequence will be selected which has rocks ranging from deeply buried geosynclinal environments (approx.300 to 400 0 C) to shallow shelf environments

Pressurized fluidized-bed hydroretorting of Eastern oil shales

Energy Technology Data Exchange (ETDEWEB)

Roberts, M.J.; Mensinger, M.C.; Rue, D.M.; Lau, F.S. (Institute of Gas Technology, Chicago, IL (United States)); Schultz, C.W. (Alabama Univ., University, AL (United States)); Parekh, B.K. (Kentucky Univ., Lexington, KY (United States)); Misra, M. (Nevada Univ., Reno, NV (United States)); Bonner, W.P. (Tennessee Technological Univ., Cookeville, TN (United States))

1992-11-01

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that beneficiated shale is the preferred feedstock for pressurized hydroretorting. The program extension is divided into the following active tasks. Task 3. testing of process improvement concepts; Task 4. beneficiation research; Task 5. operation of PFH on beneficiated shale; Task 6. environmental data and mitigation analyses; Task 7. sample procurement, preparation, and characterization; and Task 8. project management and reporting. In order to accomplish all the program objectives, the Institute of Gas Technology (IGT), the prime contractor, worked with four other institutions: the University of Alabama/Mineral Resources Institute (MRI), the University of Kentucky Center for Applied Energy Research (UK-CAER), the University of Nevada (UN) at Reno, and Tennessee Technological University (TTU). This report presents the work performed during the program extension from June 1, 1991 through May 31, 1992.

Ichnology applied to sequence stratigraphic analysis of Siluro-Devonian mud-dominated shelf deposits, Paraná Basin, Brazil

Science.gov (United States)

Sedorko, Daniel; Netto, Renata G.; Savrda, Charles E.

2018-04-01

Previous studies of the Paraná Supersequence (Furnas and Ponta Grossa formations) of the Paraná Basin in southern Brazil have yielded disparate sequence stratigraphic interpretations. An integrated sedimentological, paleontological, and ichnological model was created to establish a refined sequence stratigraphic framework for this succession, focusing on the Ponta Grossa Formation. Twenty-nine ichnotaxa are recognized in the Ponta Grossa Formation, recurring assemblages of which define five trace fossil suites that represent various expressions of the Skolithos, Glossifungites and Cruziana ichnofacies. Physical sedimentologic characteristics and associated softground ichnofacies provide the basis for recognizing seven facies that reflect a passive relationship to bathymetric gradients from shallow marine (shoreface) to offshore deposition. The vertical distribution of facies provides the basis for dividing the Ponta Grossa Formation into three major (3rd-order) depositional sequences- Siluro-Devonian and Devonian I and II-each containing a record of three to seven higher-order relative sea-level cycles. Major sequence boundaries, commonly coinciding with hiatuses recognized from previously published biostratigraphic data, are locally marked by firmground Glossifungites Ichnofacies associated with submarine erosion. Maximum transgressive horizons are prominently marked by unbioturbated or weakly bioturbated black shales. By integrating observations of the Ponta Grossa Formation with those recently made on the underlying marginal- to shallow-marine Furnas Formation, the entire Paraná Supersequence can be divided into four disconformity-bound sequences: a Lower Silurian (Llandovery-Wenlock) sequence, corresponding to lower and middle units of the Furnas; a Siluro-Devonian sequence (?Pridoli-Early Emsian), and Devonian sequences I (Late Emsian-Late Eifelian) and II (Late Eifelian-Early Givetian). Stratigraphic positions of sequence boundaries generally coincide with

Heterogeneity of shale documented by micro-FTIR and image analysis.

Science.gov (United States)

Chen, Yanyan; Mastalerz, Maria; Schimmelmann, Arndt

2014-12-01

In this study, four New Albany Shale Devonian and Mississippian samples, with vitrinite reflectance [Ro ] values ranging from 0.55% to 1.41%, were analyzed by micro-FTIR mapping of chemical and mineralogical properties. One additional postmature shale sample from the Haynesville Shale (Kimmeridgian, Ro = 3.0%) was included to test the limitation of the method for more mature substrates. Relative abundances of organic matter and mineral groups (carbonates, quartz and clays) were mapped across selected microscale regions based on characteristic infrared peaks and demonstrated to be consistent with corresponding bulk compositional percentages. Mapped distributions of organic matter provide information on the organic matter abundance and the connectivity of organic matter within the overall shale matrix. The pervasive distribution of organic matter mapped in the New Albany Shale sample MM4 is in agreement with this shale's high total organic carbon abundance relative to other samples. Mapped interconnectivity of organic matter domains in New Albany Shale samples is excellent in two early mature shale samples having Ro values from 0.55% to 0.65%, then dramatically decreases in a late mature sample having an intermediate Ro of 1.15% and finally increases again in the postmature sample, which has a Ro of 1.41%. Swanson permeabilities, derived from independent mercury intrusion capillary pressure porosimetry measurements, follow the same trend among the four New Albany Shale samples, suggesting that micro-FTIR, in combination with complementary porosimetric techniques, strengthens our understanding of porosity networks. In addition, image processing and analysis software (e.g. ImageJ) have the capability to quantify organic matter and total organic carbon - valuable parameters for highly mature rocks, because they cannot be analyzed by micro-FTIR owing to the weakness of the aliphatic carbon-hydrogen signal. © 2014 The Authors Journal of Microscopy © 2014 Royal

Peeking out of the basins: looking for the Late Devonian Kellwasser Event in the open ocean in the Central Asian Orogenic Belt, southwestern Mongolia

Science.gov (United States)

Thomas, R. M., Jr.; Carmichael, S. K.; Waters, J. A.; Batchelor, C. J.

2017-12-01

Two of the top five most devastating mass extinctions in Earth's history occurred during the Late Devonian (419.2 Ma - 358.9 Ma), and are commonly associated with the black shale deposits of the Kellwasser and Hangenberg ocean anoxia events. Our understanding of these extinction events is incomplete partly due to sample bias, as 95% of the field sites studying the Late Devonian are limited to continental shelves and continental marine basins, and 77% of these sites are derived from the Euramerican paleocontinent. The Samnuuruul Formation at the Hoshoot Shiveetiin Gol locality (HSG), located in southwestern Mongolia, offers a unique opportunity to better understand global oceanic conditions during the Late Devonian. The HSG locality shows a continuous sequence of terrestrial to marine sediments on the East Junggar arc; an isolated, open-ocean island arc within the Central Asian Orogenic Belt (CAOB). Samples from this near shore locality consist of volcanogenic silts, sands and immature conglomerates as well as calc-alkalic basalt lava flows. Offshore sections contain numerous limestones with Late Devonian fossil assemblages. Preliminary biostratigraphy of the associated marine and terrestrial sequences can only constrain the section to a general Late Devonian age, but TIMS analysis of detrital zircons from volcanogenic sediments from the Samnuuruul Formation in localities 8-50 km from the site suggests a late Frasnian age (375, 376 Ma). To provide a more precise radiometric age of the HSG locality, zircon geochronology using laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) will be performed at UNC-Chapel Hill. If the HSG section crosses the Frasnian-Famennian boundary, geochemical, mineralogical, and ichnological signatures of the Kellwasser Event are expected to be preserved, if the Kellwasser Event was indeed global in scope (as suggested by Carmichael et al. (2014) for analogous sites on the West Junggar arc in the CAOB). Black shale

Biogeography of late Silurian and devonian rugose corals

Science.gov (United States)

Oliver, W.A.

1977-01-01

Three marine benthic faunal realms can be recognized in the Early and Middle Devonian. The Eastern Americas Realm consisted of most of the eastern half of North America and South America north of the Amazon. This realm extended in a southwest direction from the Devonian equator to approximately 35??S and was an isolated epicontinental sea during much of its history. The Eastern Americas Realm was bounded on the west by the Transcontinental Arch, on the north by the Canadian Shield and on the east and southeast by a peninsular extension of the Old Red Continent. These barriers were emergent during much, but not all, of Devonian time. Seaways beyond these barriers belonged to the Old World Realm. The Malvinokaffric Realm that was farther south was apparently temperate to arctic in climate and latitudinal position and contained few corals. Rugose corals in the Eastern Americas Realm show increasing generic-level endemism from the Late Silurian through the Early Devonian; during the late Early Devonian, 92% of the rugosan genera are not known anywhere else in the world. Endemism decreased through the Middle Devonian to zero in the early Late Devonian. The Early Devonian increase in endemism paralleled, and was probably related to, the development of the Old Red Continent as a barrier between America and Africa-Europe. The waning of endemism in the Middle Devonian reflects the breaching of the land barriers. This permitted some migration in and out of the realm in early Middle Devonian time but greatest movements were in late Middle Devonian time. Principal migration directions were from western or Arctic North America into the Michigan-Hudson Bay area and from the southern Appalachian area into Africa. ?? 1977.

Geologic and geochemical studies of the New Albany Shale Group (Devonian-Mississippian) in Illinois. Final report

Energy Technology Data Exchange (ETDEWEB)

Bergstrom, R.E.; Shimp, N.F.

1980-06-30

The Illinois State Geological Survey is conducting geological and geochemical investigations to evaluate the potential of New Albany Group shales as a source of hydrocarbons, particularly natural gas. Geological studies include stratigraphy and structure, mineralogic and petrographic characterization; analyses of physical properties; and development of a computer-based resources evaluation system. Geochemical studies include organic carbon content and trace elements; hydrocarbon content and composition; and adsorption/desorption studies of gas through shales. Separate abstracts have been prepared for each task reported.

Liberation play : technology and prices help release shale gas from unconventional status

International Nuclear Information System (INIS)

Roche, P.

2006-01-01

Shale gas production is set to increase in Canada. The British Columbia (BC) Oil and Gas Commission has approved more than 20 blocks of potential shale lands as experimental scheme areas targeting Cretaceous-age and Devonian-age shales. The BC government is currently working on a royalty scheme to benefit shale gas producers by allowing them to defer the bulk of the royalty collection until projects have reached a certain economic payout point. Interest in unconventional gas has spawned activity in previously unexplored areas of BC. Coals and shales are currently being evaluated near the community of Hudson's Hope, which has an estimated 1.8 tcf of shale gas. Canadian Spirit Resources Inc., who have leased the land, are now focusing on optimizing production processes to improve the economics of shale gas recovery. In Saskatchewan, shale gas exploration is occurring in the central region of the province, far from existing oil and gas production. PanTerra Resources Corp. has recently drilled 16 wells on its Foam Lake project, and detailed core and log analyses are being conducted to improve the understanding of the lithology and rock fabric and allow the company to design completion and stimulation programs. Stealth Ventures Ltd. is concentrating on developing the tight, biogenic Colorado Shale, which extends from Manitoba to the foothills of Alberta. Because of the shallow depths, the initial drilling costs are lower for biogenic gas than for thermogenic gas. Success will depend on the right drilling and completion methods. Junior explorers are also exploring for shale gas in an area straddling the St. Lawrence River between Quebec City and Montreal. Several large companies are examining the economic potential of shale gas production throughout North America. It was concluded that oil and gas operators are becoming more confident that domestic shale gas resources will be cheaper in future than imported liquefied natural gas (LNG), which requires special ships

Diagenetic conditions of fibrous calcite vein formation in black shales: Petrographic, chemical and isotopic evidence

Energy Technology Data Exchange (ETDEWEB)

Al-Aasm, I.S.; Muir, I. (Imperial Oil Resources, Calgary, AB (Canada)); Morad, S. (Windsor Univ., ON (Canada))

1992-03-01

Antiaxial fibrous calcite veins 2-6 cm thick outcrop parallel to bedding in the Bluefish Member of the Middle Devonian Hare Indian Formation in the Norman Wells area of the Northwest Territories. The Bluefish Member consists of dark brown to black laminated shales with total organic matter content in the 1.8-8.0 wt % range. The basal part of the Member, characterized by the presence of low diversity macrofossils, was deposited under anaerobic conditions on top of the drowned Hume carbonate platform. The pattern of incorporation of host-shale fragments and tiny inclusions into the fibrous calcite indicates repeated episodes of vein opening and sealing. The [delta][sup 13]C values and the low Mn and Fe contents indicate a dominantly marine source of carbonate ions was related to the dissolution of metastable skeletal carbonates in the host shales. The [delta][sup 18]O values suggest precipitation at 30-50[degree]C and burial depths of tens to hundreds of meters. The formation of finely crystalline non-stoichiometric Ca-rich dolomite disseminated in the shale inclusions occurred subsequent to the emplacement of fibrous calcite veins under elevated burial temperatures. 54 refs., 8 figs., 3 tabs.

Biogenic gas in the Cambrian-Ordovcian Alum Shale (Denmark and Sweden)

Energy Technology Data Exchange (ETDEWEB)

Schulz, H.M.; Wirth, R.; Biermann, S.; Arning, E.T. [Helmholtz-Zentrum Potsdam - Deutsches GeoForschungsZentrum GFZ, Potsdam (Germany); Krueger, M.; Straaten, N. [BGR Hannover (Germany); Bechtel, A. [Montanuniv. Leoben (Austria); Berk, W. van [Technical Univ. of Clausthal (Germany); Schovsbo, N.H. [Geological Survey of Denmark and Greenland - GEUS, Copenhagen (Denmark); Crabtree, Stephen [Gripen Gas (Sweden)

2013-08-01

Shale gas is mainly produced from thermally mature black shales. However, biogenic methane also represents a resource which is often underestimated. Today biogenic methane is being produced from the Upper Devonian Antrim Shale in the Michigan Basin which was the most successfully exploited shale gas system during the 1990-2000 decade in the U.S.A. before significant gas production from the Barnett Shale started (Curtis et al., 2008). The Cambro-Ordovician Alum Shale in northern Europe has thermal maturities ranging from overmature in southern areas (Denmark and southern Sweden) to immature conditions (central Sweden). Biogenic methane is recorded during drilling in central Sweden. The immature Alum Shale in central Sweden has total organic carbon (TOC) contents up to 20 wt%. The hydrogen index HI ranges from 380 to 560 mgHC/gTOC at very low oxygen index (OI) values of around 4 mg CO{sub 2}/gTOC, Tmax ranges between 420 - 430 C. The organic matter is highly porous. In general, the Alum Shale is a dense shale with intercalated sandy beds which may be dense due to carbonate cementation. Secondary porosity is created in some sandy beds due to feldspar dissolution and these beds serve as gas conduits. Methane production rates with shale as substrate in the laboratory are dependent on the kind of hydrocarbon-degrading microbial enrichment cultures used in the incubation experiments, ranging from 10-620 nmol/(g*d). In these experiments, the CO{sub 2} production rate was always higher than for methane. Like the northern part of North America, also Northern European has been covered by glaciers during the Pleistocene and similar geological processes may have developed leading to biogenic shale gas formation. For the Antrim Shale one hypothesis suggests that fresh waters, recharged from Pleistocene glaciation and modern precipitation, suppressed basinal brine salinity along the northern margins of the Michigan Basin to greater depths and thereby enhancing methanogenesis

Eastern gas shales bibliography selected annotations: gas, oil, uranium, etc. Citations in bituminous shales worldwide

Energy Technology Data Exchange (ETDEWEB)

Hall, V.S. (comp.)

1980-06-01

This bibliography contains 2702 citations, most of which are annotated. They are arranged by author in numerical order with a geographical index following the listing. The work is international in scope and covers the early geological literature, continuing through 1979 with a few 1980 citations in Addendum II. Addendum I contains a listing of the reports, well logs and symposiums of the Unconventional Gas Recovery Program (UGR) through August 1979. There is an author-subject index for these publications following the listing. The second part of Addendum I is a listing of the UGR maps which also has a subject-author index following the map listing. Addendum II includes several important new titles on the Devonian shale as well as a few older citations which were not found until after the bibliography had been numbered and essentially completed. A geographic index for these citations follows this listing.

Pressurized Fluidized-Bed Hydroretorting of eastern oil shales. Final report, June 1992--January 1993

Energy Technology Data Exchange (ETDEWEB)

Roberts, M.J.; Mensinger, M.C.; Erekson, E.J.; Rue, D.M.; Lau, F.S. [Institute of Gas Technology, Chicago, IL (United States); Schultz, C.W.; Hatcher, W.E. [Alabama Univ., University, AL (United States). Mineral Resources Inst.; Parekh, B.K. [Kentucky Univ., Lexington, KY (United States). Center for Applied Energy Research; Bonner, W.P. [Tennessee Technological Univ., Cookeville, TN (United States)

1993-03-01

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in September 1987 by the US Department of Energy was to perform the research necessary to develop the pressurized fluidized-bed hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation and upgrading, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The program was divided into the following active tasks: Task 3 -- Testing of Process Improvement Concepts; Task 4 -- Beneficiation Research; Task 6 -- Environmental Data and Mitigation Analyses; and Task 9 -- Information Required for the National Environmental Policy Act. In order to accomplish all of the program objectives, tho Institute of Gas Technology (ICT), the prime contractor, worked with four other institutions: The University of Alabama/Mineral Resources Institute (MRI), the University of Alabama College of Engineering (UA), University of Kentucky Center for Applied Energy Research (UK-CAER), and Tennessee Technological University (TTU). This report presents the work performed by IGT from June 1, 1992 through January 31, 1993.

Stratigraphic architecture of Devonian lacustrine basins of northern Scotland

DEFF Research Database (Denmark)

Kristiansen, Thorben; Moreau, Julien; Andrews, Steven D.

of this important surface has received relatively little attention. We have utilized vintage onshore seismic to gain a better understanding of the pre-Devonian basement physiography. Onshore exposures of the top Moine, base Devonian unconformity surface is exposed have been visited to ground truth our subsurface...... interpretations. The studied deposits have been deeply buried then exhumed so that they are exposed widely onshore. Post Caledonian tectonism has faulted and folded the Devonian succession making it challenging to reconstruct the stratigraphy and the basin architecture from geological data only. The Devonian...

The fluoride in the groundwater of Guarani Aquifer System: the origin associated with black shales of Paraná Basin

Science.gov (United States)

Kern, M. L.; Vieiro, A. P.; Machado, G.

2008-09-01

This work presents petrological and geochemical results of the black shales interval from Permian and Devonian strata of the Paraná Basin, Brazil and its relationships with fluoride of groundwater from Guarani Aquifer System. The Guarani Aquifer, located in South Brazil, Uruguay, Paraguay and Argentine, presents contents of fluoride higher than the Brazilian accepted potability limits. Several hypotheses have been presented for the origin of the fluoride in the groundwater of the Guarani Aquifer. Microcrystalline fluorite was registered in black shales of Ponta Grossa and Irati formations from Paraná Basin. The results shown in this work suggest that fluoride present in groundwater of Guarani Aquifer can be originated in deeper groundwater that circulates in Ponta Grossa and Irati formations. The interaction of the groundwater coming from deeper black shales with the groundwater-bearing Aquifer Guarani System occurs through regional fragile structures (faults and fractures) that constitute excellent hydraulic connectors between the two sedimentary packages. The microcrystalline fluorite registered in Ponta Grossa and Irati Formations can be dissolved promoting fluoride enrichment in groundwater of these black shales and Guarani Aquifer System.

Devonian climate and reef evolution: Insights from oxygen isotopes in apatite

Science.gov (United States)

Joachimski, M. M.; Breisig, S.; Buggisch, W.; Talent, J. A.; Mawson, R.; Gereke, M.; Morrow, J. R.; Day, J.; Weddige, K.

2009-07-01

Conodonts, microfossils composed of carbonate-fluor apatite, are abundant in Palaeozoic-Triassic sediments and have a high potential to preserve primary oxygen isotope signals. In order to reconstruct the palaeotemperature history of the Devonian, the oxygen isotope composition of apatite phosphate was measured on 639 conodont samples from sequences in Europe, North America and Australia. The Early Devonian (Lochkovian; 416-411 Myr) was characterized by warm tropical temperatures of around 30 °C. A cooling trend started in the Pragian (410 Myr) with intermediate temperatures around 23 to 25 °C reconstructed for the Middle Devonian (397-385 Myr). During the Frasnian (383-375 Myr), temperatures increased again with temperatures to 30 °C calculated for the Frasnian-Famennian transition (375 Myr). During the Famennian (375-359 Myr), surface water temperatures slightly decreased. Reconstructed Devonian palaeotemperatures do not support earlier views suggesting the Middle Devonian was a supergreenhouse interval, an interpretation based partly on the development of extensive tropical coral-stromatoporoid communities during the Middle Devonian. Instead, the Devonian palaeotemperature record suggests that Middle Devonian coral-stromatoporoid reefs flourished during cooler time intervals whereas microbial reefs dominated during the warm to very warm Early and Late Devonian.

Geochemical and strontium isotope characterization of produced waters from Marcellus Shale natural gas extraction.

Science.gov (United States)

Chapman, Elizabeth C; Capo, Rosemary C; Stewart, Brian W; Kirby, Carl S; Hammack, Richard W; Schroeder, Karl T; Edenborn, Harry M

2012-03-20

Extraction of natural gas by hydraulic fracturing of the Middle Devonian Marcellus Shale, a major gas-bearing unit in the Appalachian Basin, results in significant quantities of produced water containing high total dissolved solids (TDS). We carried out a strontium (Sr) isotope investigation to determine the utility of Sr isotopes in identifying and quantifying the interaction of Marcellus Formation produced waters with other waters in the Appalachian Basin in the event of an accidental release, and to provide information about the source of the dissolved solids. Strontium isotopic ratios of Marcellus produced waters collected over a geographic range of ~375 km from southwestern to northeastern Pennsylvania define a relatively narrow set of values (ε(Sr)(SW) = +13.8 to +41.6, where ε(Sr) (SW) is the deviation of the (87)Sr/(86)Sr ratio from that of seawater in parts per 10(4)); this isotopic range falls above that of Middle Devonian seawater, and is distinct from most western Pennsylvania acid mine drainage and Upper Devonian Venango Group oil and gas brines. The uniformity of the isotope ratios suggests a basin-wide source of dissolved solids with a component that is more radiogenic than seawater. Mixing models indicate that Sr isotope ratios can be used to sensitively differentiate between Marcellus Formation produced water and other potential sources of TDS into ground or surface waters.

Pressurized fluidized-bed hydroretorting of Eastern oil shales. Annual report, June 1991--May 1992

Energy Technology Data Exchange (ETDEWEB)

Roberts, M.J.; Mensinger, M.C.; Rue, D.M.; Lau, F.S. [Institute of Gas Technology, Chicago, IL (United States); Schultz, C.W. [Alabama Univ., University, AL (United States); Parekh, B.K. [Kentucky Univ., Lexington, KY (United States); Misra, M. [Nevada Univ., Reno, NV (United States); Bonner, W.P. [Tennessee Technological Univ., Cookeville, TN (United States)

1992-11-01

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that beneficiated shale is the preferred feedstock for pressurized hydroretorting. The program extension is divided into the following active tasks. Task 3. testing of process improvement concepts; Task 4. beneficiation research; Task 5. operation of PFH on beneficiated shale; Task 6. environmental data and mitigation analyses; Task 7. sample procurement, preparation, and characterization; and Task 8. project management and reporting. In order to accomplish all the program objectives, the Institute of Gas Technology (IGT), the prime contractor, worked with four other institutions: the University of Alabama/Mineral Resources Institute (MRI), the University of Kentucky Center for Applied Energy Research (UK-CAER), the University of Nevada (UN) at Reno, and Tennessee Technological University (TTU). This report presents the work performed during the program extension from June 1, 1991 through May 31, 1992.

Stratigraphy and facies development of the marine Late Devonian near the Boulongour Reservoir, northwest Xinjiang, China

Science.gov (United States)

Suttner, Thomas J.; Kido, Erika; Chen, Xiuqin; Mawson, Ruth; Waters, Johnny A.; Frýda, Jiří; Mathieson, David; Molloy, Peter D.; Pickett, John; Webster, Gary D.; Frýdová, Barbora

2014-02-01

Late Devonian to Early Carboniferous stratigraphic units within the 'Zhulumute' Formation, Hongguleleng Formation (stratotype), 'Hebukehe' Formation and the Heishantou Formation near the Boulongour Reservoir in northwestern Xinjiang are fossil-rich. The Hongguleleng and 'Hebukehe' formations are biostratigraphically well constrained by microfossils from the latest Frasnian linguiformis to mid-Famennian trachytera conodont biozones. The Hongguleleng Formation (96.8 m) is characterized by bioclastic argillaceous limestones and marls (the dominant facies) intercalated with green spiculitic calcareous shales. It yields abundant and highly diverse faunas of bryozoans, brachiopods and crinoids with subordinate solitary rugose corals, ostracods, trilobites, conodonts and other fish teeth. The succeeding 'Hebukehe' Formation (95.7 m) consists of siltstones, mudstones, arenites and intervals of bioclastic limestone (e.g. 'Blastoid Hill') and cherts with radiolarians. A diverse ichnofauna, phacopid trilobites, echinoderms (crinoids and blastoids) together with brachiopods, ostracods, bryozoans and rare cephalopods have been collected from this interval. Analysis of geochemical data, microfacies and especially the distribution of marine organisms, which are not described in detail here, but used for facies analysis, indicate a deepening of the depositional environment at the Boulongour Reservoir section. Results presented here concern mainly the sedimentological and stratigraphical context of the investigated section. Additionally, one Late Devonian palaeo-oceanic and biotic event, the Upper Kellwasser Event is recognized near the section base.

Geologic report of the Maquoketa Shale, New Albany Shale, and Borden Group rocks in the Illinois Basin as potential solid waste repository sites

International Nuclear Information System (INIS)

Droste, J.B.; Vitaliano, C.J.

1976-06-01

We have evaluated the Illinois Basin in order to select a ''target site'' for a possible solid nuclear waste repository. In the process we have been mindful of geology (particularly stratigraphy and lithology and structure), terrane, population density, land use, land ownership and accessibility. After taking these restrictions into account, we have singled out a strip of land in south central Indiana in which we have selected four potential sites worthy of further exploration. In three of the sites the geology, lithology, and depth below the surface are more than adequate for crypt purposes in two separate formations--the Maquoketa Shale of the Ordovician System and the New Albany Shale-Borden Group of the Upper Devonian-Mississippian Systems. The interval between the two is several hundred feet. The geology and associated features in the fourth site are undoubtedly similar to those in the first three. In all four selections a sizeable proportion of the land is in public ownership and the population density in the nonpublicly owned land is low. The geology, lithology, and position of the target formations have been projected into the sites in question from data provided by drill core records of the Indiana Geological Survey. Precise details would, of course, require exploratory drilling on the selected site

Paleozoic oil/gas shale reservoirs in southern Tunisia: An overview

Science.gov (United States)

Soua, Mohamed

2014-12-01

During these last years, considerable attention has been given to unconventional oil and gas shale in northern Africa where the most productive Paleozoic basins are located (e.g. Berkine, Illizi, Kufra, Murzuk, Tindouf, Ahnet, Oued Mya, Mouydir, etc.). In most petroleum systems, which characterize these basins, the Silurian played the main role in hydrocarbon generation with two main 'hot' shale levels distributed in different locations (basins) and their deposition was restricted to the Rhuddanian (Lllandovery: early Silurian) and the Ludlow-Pridoli (late Silurian). A third major hot shale level had been identified in the Frasnian (Upper Devonian). Southern Tunisia is characterized by three main Paleozoic sedimentary basins, which are from North to South, the southern Chotts, Jeffara and Berkine Basin. They are separated by a major roughly E-W trending lower Paleozoic structural high, which encompass the Mehrez-Oued Hamous uplift to the West (Algeria) and the Nefusa uplift to the East (Libya), passing by the Touggourt-Talemzane-PGA-Bou Namcha (TTPB) structure close to southern Tunisia. The forementioned major source rocks in southern Tunisia are defined by hot shales with elevated Gamma ray values often exceeding 1400 API (in Hayatt-1 well), deposited in deep water environments during short lived (c. 2 Ma) periods of anoxia. In the course of this review, thickness, distribution and maturity maps have been established for each hot shale level using data for more than 70 wells located in both Tunisia and Algeria. Mineralogical modeling was achieved using Spectral Gamma Ray data (U, Th, K), SopectroLith logs (to acquire data for Fe, Si and Ti) and Elemental Capture Spectroscopy (ECS). The latter technique provided data for quartz, pyrite, carbonate, clay and Sulfur. In addition to this, the Gamma Ray (GR), Neutron Porosity (ΦN), deep Resistivity (Rt) and Bulk Density (ρb) logs were used to model bulk mineralogy and lithology. Biostratigraphic and complete

Placoderms (Armored Fish): Dominant Vertebrates of the Devonian Period

Science.gov (United States)

Young, Gavin C.

2010-05-01

Placoderms, the most diverse group of Devonian fishes, were globally distributed in all habitable freshwater and marine environments, like teleost fishes in the modern fauna. Their known evolutionary history (Early Silurian-Late Devonian) spanned at least 70 million years. Known diversity (335 genera) will increase when diverse assemblages from new areas are described. Placoderms first occur in the Early Silurian of China, but their diversity remained low until their main evolutionary radiation in the Early Devonian, after which they became the dominant vertebrates of Devonian seas. Most current placoderm data are derived from the second half of the group's evolutionary history, and recent claims that they form a paraphyletic group are based on highly derived Late Devonian forms; 16 shared derived characters are proposed here to support placoderm monophyly. Interrelationships of seven placoderm orders are unresolved because Silurian forms from China are still poorly known. The relationship of placoderms to the two major extant groups of jawed fishes—osteichthyans (bony fishes) and chondrichthyans (cartilaginous sharks, rays, and chimaeras)—remains uncertain, but the detailed preservation of placoderm internal braincase structures provides insights into the ancestral gnathostome (jawed vertebrate) condition. Placoderms provide the most complex morphological and biogeographic data set for the Middle Paleozoic; marked discrepancies in stratigraphic occurrence between different continental regions indicate strongly endemic faunas that were probably constrained by marine barriers until changes in paleogeography permitted range enlargement into new areas. Placoderm distributions in time and space indicate major faunal interchange between Gondwana and Laurussia near the Frasnian-Famennian boundary; closure of the Devonian equatorial ocean is a possible explanation.

How Reducing was the Late Devonian Ocean? The Role of Extensive Expansion of Anoxia in Marine Biogeochemical Cycles of Redox Sensitive Metals.

Science.gov (United States)

Sahoo, S. K.; Jin, H.

2017-12-01

The evolution of Earth's biogeochemical cycles is intimately linked to the oxygenation of the oceans and atmosphere. The Late Devonian is no exception as its characterized with mass extinction and severe euxinia. Here we use concentrations of Molybdenum (Mo), Vanadium (V), Uranium (U) and Chromium (Cr) in organic rich black shales from the Lower Bakken Formation of the Williston Basin, to explore the relationship between extensive anoxia vs. euxinia and it's relation with massive release of oxygen in the ocean atmosphere system. XRF data from 4 core across the basin shows that modern ocean style Mo, U and Cr enrichments are observed throughout the Lower Bakken Formation, yet V is not enriched until later part of the formation. Given the coupling between redox-sensitive-trace element cycles and ocean redox, various models for Late Devonian ocean chemistry imply different effects on the biogeochemical cycling of major and trace nutrients. Here, we examine the differing redox behavior of molybdenum and vanadium under an extreme anoxia and relatively low extent of euxinia. The model suggests that Late Devonian was perhaps extensively anoxic- 40-50% compared to modern seafloor area, and a very little euxinia. Mo enrichments extend up to 500 p.p.m. throughout the section, representative of a modern reducing ocean. However, coeval low V enrichments only support towards anoxia, where anoxia is a source of V, and a sink for Mo. Our model suggests that the oceanic V reservoir is extremely sensitive to perturbations in the extent of anoxic condition, particularly during post glacial times.

East Greenland tetrapods are Devonian in age

Science.gov (United States)

Marshall, J. E. A.; Astin, T. R.; Clack, J. A.

1999-07-01

Palynological dates unambiguously resolve the stratigraphic age of the East Greenland sedimentary rocks containing the earliest well-preserved tetrapod remains. This is the first time that spore samples have been discovered in the sedimentary succession that has yielded Acanthostega and Ichthyostega, two tetrapods that are regarded as critically important taxa for our understanding of the origin and early evolution of the tetrapods. These palynological assemblages conclusively show that the rocks are Devonian in age. The evidence resolves a 60-year-old dispute regarding the age of these rocks and contradicts a recent controversial study suggesting a much younger (Carboniferous, Viséan) age for these tetrapods. Spore samples bracketing the in situ occurrences of both tetrapod genera place them securely within the Famennian Age of the Devonian Period and at least as old as Famennian 2b. The ages of all known Devonian tetrapods are reviewed and related to a common palynological standard. This review places Ichthyostega and Acanthostega as the earliest of the Famennian tetrapods.

Weathering of the New Albany Shale, Kentucky, USA: I. Weathering zones defined by mineralogy and major-element composition

Science.gov (United States)

Tuttle, M.L.W.; Breit, G.N.

2009-01-01

Comprehensive understanding of chemical and mineralogical changes induced by weathering is valuable information when considering the supply of nutrients and toxic elements from rocks. Here minerals that release and fix major elements during progressive weathering of a bed of Devonian New Albany Shale in eastern Kentucky are documented. Samples were collected from unweathered core (parent shale) and across an outcrop excavated into a hillside 40 year prior to sampling. Quantitative X-ray diffraction mineralogical data record progressive shale alteration across the outcrop. Mineral compositional changes reflect subtle alteration processes such as incongruent dissolution and cation exchange. Altered primary minerals include K-feldspars, plagioclase, calcite, pyrite, and chlorite. Secondary minerals include jarosite, gypsum, goethite, amorphous Fe(III) oxides and Fe(II)-Al sulfate salt (efflorescence). The mineralogy in weathered shale defines four weathered intervals on the outcrop-Zones A-C and soil. Alteration of the weakly weathered shale (Zone A) is attributed to the 40-a exposure of the shale. In this zone, pyrite oxidization produces acid that dissolves calcite and attacks chlorite, forming gypsum, jarosite, and minor efflorescent salt. The pre-excavation, active weathering front (Zone B) is where complete pyrite oxidation and alteration of feldspar and organic matter result in increased permeability. Acidic weathering solutions seep through the permeable shale and evaporate on the surface forming abundant efflorescent salt, jarosite and minor goethite. Intensely weathered shale (Zone C) is depleted in feldspars, chlorite, gypsum, jarosite and efflorescent salts, but has retained much of its primary quartz, illite and illite-smectite. Goethite and amorphous FE(III) oxides increase due to hydrolysis of jarosite. Enhanced permeability in this zone is due to a 14% loss of the original mass in parent shale. Denudation rates suggest that characteristics of Zone C

Productivity Contribution of Paleozoic Woodlands to the Formation of Shale-Hosted Massive Sulfide Deposits in the Iberian Pyrite Belt (Tharsis, Spain)

Science.gov (United States)

Fernández-Remolar, David C.; Harir, Mourad; Carrizo, Daniel; Schmitt-Kopplin, Philippe; Amils, Ricardo

2018-03-01

The geological materials produced during catastrophic and destructive events are an essential source of paleobiological knowledge. The paleobiological information recorded by such events can be rich in information on the size, diversity, and structure of paleocommunities. In this regard, the geobiological study of late Devonian organic matter sampled in Tharsis (Iberian Pyrite Belt) provided some new insights into a Paleozoic woodland community, which was recorded as massive sulfides and black shale deposits affected by a catastrophic event. Sample analysis using TOF-SIMS (Time of Flight Secondary Ion Mass Spectrometer), and complemented by GC/MS (Gas Chromatrograph/Mass Spectrometer) identified organic compounds showing a very distinct distribution in the rock. While phytochemical compounds occur homogeneously in the sample matrix that is composed of black shale, the microbial-derived organics are more abundant in the sulfide nodules. The cooccurrence of sulfur bacteria compounds and the overwhelming presence of phytochemicals provide support for the hypothesis that the formation of the massive sulfides resulted from a high rate of vegetal debris production and its oxidation through sulfate reduction under suboxic to anoxic conditions. A continuous supply of iron from hydrothermal activity coupled with microbial activity was strictly necessary to produce this massive orebody. A rough estimate of the woodland biomass was made possible by accounting for the microbial sulfur production activity recorded in the metallic sulfide. As a result, the biomass size of the late Devonian woodland community was comparable to modern woodlands like the Amazon or Congo rainforests.

Yield and characteristics of shale oil from the retorting of oil shale and fine oil-shale ash mixtures

International Nuclear Information System (INIS)

Niu, Mengting; Wang, Sha; Han, Xiangxin; Jiang, Xiumin

2013-01-01

Highlights: • The whole formation process of shale oil might be divided into four stages. • Higher ash/shale mass ratio intensified the cracking and coking of shale oil. • Ash/shale ratio of 1:2 was recommended for oil shale fluidized bed retort with fine oil-shale ash as solid heat carrier. - Abstract: For exploring and optimizing the oil shale fluidized bed retort with fine oil-shale ash as a solid heat carrier, retorting experiments of oil shale and fine oil-shale ash mixtures were conducted in a lab-scale retorting reactor to investigate the effects of fine oil-shale ash on shale oil. Oil shale samples were obtained from Dachengzi Mine, China, and mixed with fine oil-shale ash in the ash/shale mass ratios of 0:1, 1:4, 1:2, 1:1, 2:1 and 4:1. The experimental retorting temperature was enhanced from room temperature to 520 °C and the average heating rate was 12 °C min −1 . It was found that, with the increase of the oil-shale ash fraction, the shale oil yield first increased and then decreased obviously, whereas the gas yield appeared conversely. Shale oil was analyzed for the elemental analysis, presenting its atomic H/C ratio of 1.78–1.87. Further, extraction and simulated distillation of shale oil were also conducted to explore the quality of shale oil. As a result, the ash/shale mixing mass ratio of 1:2 was recommended only for the consideration of increasing the yield and quality of shale oil

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1946-08-29

A continuous method of distilling shale to produce valuable hydrocarbon oils is described which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors from the zone, mixing fresh cold shale with the hydrocarbon vapors to quench the same, whereby the fresh shale is preheated, recovering hydrocarbon vapors and product vapors from the mixture and withdrawing preheated shale from the mixture and charging it to a shale distillation zone.

Importance of inorganic geochemical characteristics on assessment of shale gas potential in the Devonian Horn River Formation of western Canada

Science.gov (United States)

Hong, Sung Kyung; Shinn, Young Jae; Choi, Jiyoung; Lee, Hyun Suk

2017-04-01

The gas generation and storage potentials of shale has mostly been assessed by original TOC (TOCo) and original kerogen type. However, in the Horn River Formation, organic geochemical tools and analysis are barely sufficient for assessing the TOCo and original kerogen type because residual carbon contents represent up to 90% of TOC in shales. Major and trace elements are used as proxies for the bottom water oxygen level, for terrestrial sediment input and for productivity, which is related with variation of kerogen type. By using the inorganic geochemical proxies, we attempt to assess original kerogen type in shale gas formation and suggest its implication for HIo (original Hydrogen Index) estimation. The estimated HIo in this study allows us to calculate a reliable TOCo. These results provide new insights into the accurate estimation of the hydrocarbon potential of shale gas resources. The inorganic geochemical proxies indicate vertical variations of productivity (EX-SiO2 and Baauth), terrestrial sediment input (Al2O3, Zr, Hf, and Nb) and oxygen content in bottom water during deposition (Moauth, Uauth and Th/U), which represent the temporal changes in the mixing ratio between Type II and III kerogens. The Horn River Formation has different HIo values calculated from EX-SiO2 (biogenic origin) and it is ranked by HIo value in descending order: Evie and Muskwa members (500-700 mgHC/gTOC) > middle Otterpark Member (400-500 mgHC/gTOC) > upper Otterpark Member (300-400 mgHC/gTOC) > lower Otterpark Member (200 mgHC/gTOC). Based on the original kerogen type and TOCo, the gas generation and storage potentials of the Evie, middle Otterpark and Muskwa members are higher than those of other members. The source rock potential is excellent for the Evie Member with a remarkable difference between TOCo and measured TOC.

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Blanding, F H

1948-08-03

A continuous method of distilling shale to produce valuable hydrocarbon oils is described, which comprises providing a fluidized mass of the shale in a distillation zone, withdrawing hydrocarbon vapors containing shale fines from the zone, mixing sufficient fresh cold shale with the hydrocarbon vapors to quench the same and to cause condensation of the higher boiling constituents thereof, charging the mixture of vapors, condensate, and cold shale to a separation zone where the shale is maintained in a fluidized condition by the upward movement of the hydrocarbon vapors, withdrawing condensate from the separation zone and recycling a portion of the condensate to the top of the separation zone where it flows countercurrent to the vapors passing therethrough and causes shale fines to be removed from the vapors by the scrubbing action of the condensate, recovering hydrocarbon vapors and product vapors from the separation zone, withdrawing preheated shale from the separation zone and charging it to a shale distillation zone.

Shale gas. Shale gas formation and extraction

International Nuclear Information System (INIS)

Renard, Francois; Artru, Philippe

2015-10-01

A first article recalls the origin of shale gases and technological breakthroughs which allowed their exploitation, describes the development of shale gas exploitation in the USA during the 2000's and the consequences for the gas and electricity markets, and discusses the various environmental impacts (risks of pollution of aquifers, risks of induced seismicity, use and processing of drilling and production waters). The second article describes the formation of shale gas: presence of organic matter in sediments, early evolution with the biogenic gas, burrowing, diagenesis and oil formation, thermal generation of gas (condensates and methane). The author indicates the location of gas within the rock, and the main sites of shale oils and shale gases in the World. In the next part, the author describes the various phases of shale gas extraction: exploration, oriented drillings, well preparation for hydraulic fracturing, fracturing, processing of fracturing fluids, flow-back, gas production and transport, aquifer protection. He finally gives a brief overview of technical evolution and of shale gas economy

Lower Devonian Brachiopods and Stratigraphy of North Palencia (Cantabrian Mountains, Spain)

NARCIS (Netherlands)

Binnekamp, J.G.

1965-01-01

A continuous sequence of Devonian sediments is exposed in the northern part of the province of Palencia (NW-Spain), on the southern slope of the Cantabrian Mountains. This study concerns the stratigraphy and paleontology of the Lower Devonian formations. At the base of the sequence a clastic

Sequence stratigraphy and a revised sea-level curve for the Middle Devonian of eastern North America

Science.gov (United States)

Brett, Carlton E.; Baird, G.C.; Bartholomew, A.J.; DeSantis, M.K.; Ver Straeten, C.A.

2011-01-01

recognizes just one major transgressive-regressive (T-R) cycle in the early-mid Givetian (If) prior to the major late Givetian Taghanic unconformity (IIa, upper Tully-Geneseo Shale), we recognize four T-R cycles: If (restricted), Ig, Ih, and Ii. We surmise that third-order sequences record eustatic sea-level fluctuations of tens of meters with periodicities of 0.8-2. myr, while their medial-scale (fourth-order) subdivisions record lesser variations primarily of 405. kyr duration (long-term eccentricity). This high-resolution record of sea-level change provides strong evidence for high-order eustatic cycles with probable Milankovitch periodicities, despite the fact that no direct evidence for Middle Devonian glacial sediments has been found to date. ?? 2010.

Chemical characterization of gas- and oil-bearing shales by instrumental neutron activation analysis

Science.gov (United States)

Frost, J.K.; Koszykowski, R.F.; Klemm, R.C.

1982-01-01

The concentration of As, Ba, Ca, Co, Cr, Cs, Dy, Eu, Fe, Ga, Hf, K, La, Lu, Mn, Mo, Na, Ni, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, Yb, and Zn were determined by instrumental neutron activation analysis in block shale samples of the New Albany Group (Devonian-Mississippian) in the in the Illinois Basin. Uranium content of the samples was as high as 75 ppm and interfered in the determination of samarium, molybdenum, barium and cerium. In the determination of selenium a correction was made for interference from tantalum. U, As, Co, Mo, Ni and Sb as well as Cu, V and pyritic sulphur which were determined by other methods, were found to correlate positively with the organic carbon content of the samples. ?? 1982 Akade??miai Kiado??.

Invasive species and biodiversity crises: testing the link in the late devonian.

Directory of Open Access Journals (Sweden)

Alycia L Stigall

Full Text Available During the Late Devonian Biodiversity Crisis, the primary driver of biodiversity decline was the dramatic reduction in speciation rates, not elevated extinction rates; however, the causes of speciation decline have been previously unstudied. Speciation, the formation of new species from ancestral populations, occurs by two primary allopatric mechanisms: vicariance, where the ancestral population is passively divided into two large subpopulations that later diverge and form two daughter species, and dispersal, in which a small subset of the ancestral population actively migrates then diverges to form a new species. Studies of modern and fossil clades typically document speciation by vicariance in much higher frequencies than speciation by dispersal. To assess the mechanism behind Late Devonian speciation reduction, speciation rates were calculated within stratigraphically constrained species-level phylogenetic hypotheses for three representative clades and mode of speciation at cladogenetic events was assessed across four clades in three phyla: Arthropoda, Brachiopoda, and Mollusca. In all cases, Devonian taxa exhibited a congruent reduction in speciation rate between the Middle Devonian pre-crisis interval and the Late Devonian crisis interval. Furthermore, speciation via vicariance is almost entirely absent during the crisis interval; most episodes of speciation during this time were due to dispersal. The shutdown of speciation by vicariance during this interval was related to widespread interbasinal species invasions. The lack of Late Devonian vicariance is diametrically opposed to the pattern observed in other geologic intervals, which suggests the loss of vicariant speciation attributable to species invasions during the Late Devonian was a causal factor in the biodiversity crisis. Similarly, modern ecosystems, in which invasive species are rampant, may be expected to exhibit similar shutdown of speciation by vicariance as an outcome of the

Invasive species and biodiversity crises: testing the link in the late devonian.

Science.gov (United States)

Stigall, Alycia L

2010-12-29

During the Late Devonian Biodiversity Crisis, the primary driver of biodiversity decline was the dramatic reduction in speciation rates, not elevated extinction rates; however, the causes of speciation decline have been previously unstudied. Speciation, the formation of new species from ancestral populations, occurs by two primary allopatric mechanisms: vicariance, where the ancestral population is passively divided into two large subpopulations that later diverge and form two daughter species, and dispersal, in which a small subset of the ancestral population actively migrates then diverges to form a new species. Studies of modern and fossil clades typically document speciation by vicariance in much higher frequencies than speciation by dispersal. To assess the mechanism behind Late Devonian speciation reduction, speciation rates were calculated within stratigraphically constrained species-level phylogenetic hypotheses for three representative clades and mode of speciation at cladogenetic events was assessed across four clades in three phyla: Arthropoda, Brachiopoda, and Mollusca. In all cases, Devonian taxa exhibited a congruent reduction in speciation rate between the Middle Devonian pre-crisis interval and the Late Devonian crisis interval. Furthermore, speciation via vicariance is almost entirely absent during the crisis interval; most episodes of speciation during this time were due to dispersal. The shutdown of speciation by vicariance during this interval was related to widespread interbasinal species invasions. The lack of Late Devonian vicariance is diametrically opposed to the pattern observed in other geologic intervals, which suggests the loss of vicariant speciation attributable to species invasions during the Late Devonian was a causal factor in the biodiversity crisis. Similarly, modern ecosystems, in which invasive species are rampant, may be expected to exhibit similar shutdown of speciation by vicariance as an outcome of the modern biodiversity

Tectono-thermal Evolution of the Lower Paleozoic Petroleum Source Rocks in the Southern Lublin Trough: Implications for Shale Gas Exploration from Maturity Modelling

Science.gov (United States)

Botor, Dariusz

2018-03-01

The Lower Paleozoic basins of eastern Poland have recently been the focus of intensive exploration for shale gas. In the Lublin Basin potential unconventional play is related to Lower Silurian source rocks. In order to assess petroleum charge history of these shale gas reservoirs, 1-D maturity modeling has been performed. In the Łopiennik IG-1 well, which is the only well that penetrated Lower Paleozoic strata in the study area, the uniform vitrinite reflectance values within the Paleozoic section are interpreted as being mainly the result of higher heat flow in the Late Carboniferous to Early Permian times and 3500 m thick overburden eroded due to the Variscan inversion. Moreover, our model has been supported by zircon helium and apatite fission track dating. The Lower Paleozoic strata in the study area reached maximum temperature in the Late Carboniferous time. Accomplished tectono-thermal model allowed establishing that petroleum generation in the Lower Silurian source rocks developed mainly in the Devonian - Carboniferous period. Whereas, during Mesozoic burial, hydrocarbon generation processes did not develop again. This has negative influence on potential durability of shale gas reservoirs.

Palynological and bulk geochemical constraints on the paleoceanographic conditions across the Frasnian-Famennian boundary, New Albany Shale, Indiana

Energy Technology Data Exchange (ETDEWEB)

Rue, Sarah R. de la [Department of Geology and Geophysics, Louisiana State University, Baton Rouge, Louisiana 70803-4101 (United States); Rowe, Harold D.; Rimmer, Susan M. [Department of Earth and Environmental Sciences, Slone Research Building, University of Kentucky, Lexington KY 40506-0053 (United States)

2007-06-01

A down-core record of stable isotope and geochemical results is integrated with palynofacies (kerogen) data from the New Albany Shale (Indiana) to reconstruct environmental changes that occurred across the Frasnian-Famennian boundary. Preliminary interpretations are focused on developing several multiproxy linkages that will potentially lead toward a more robust understanding of the occurrence and significance of phytoplankton assemblage variations during the Late Devonian, a time of widespread black shale formation. Development of such linkages will potentially provide a more comprehensive assessment of the various controls on 1) primary production, and 2) carbon sequestration in a large, low-paleolatitude intracratonic basin. An abrupt change in the geochemical and biotic proxies for particulate organic matter across the Frasnian-Famennian boundary coincides with a distinct lithological change, characterized by laminated, brownish-black Famennian mudstones unconformably overlying alternating bioturbated, greenish-gray and non-bioturbated, dark-gray Frasnian mudstones. Elemental and isotopic profiles reflect different patterns of production, degradation, and removal of organic carbon in the two shale facies. A shift from acritarch- to prasinophyte-dominated waters across the boundary indicates the overall importance of bathymetric fluctuations, chemico-physical conditions, and nutrient availability related to eustatic sea-level change. A positive {delta}{sup 13}C{sub V-PDB} shift of 1.1 permille across the boundary is interpreted to be correlative with the global Upper Kellwasser Event. A preliminary model is proposed to explain the sustainable primary production during times of maximum flooding, thereby enhancing organic preservation during black shale formation. (author)

Global iridium anomaly, mass extinction, and redox change at the Devonian-Carboniferous boundary

Energy Technology Data Exchange (ETDEWEB)

Wang, K. (Geological Survey of Canada, Calgary, Alberta (Canada) Univ. of Calgary, Alberta (Canada)); Attrep, M. Jr.; Orth, C.J. (Los Alamos National Lab., NM (United States))

1993-12-01

Iridium abundance anomalies have been found on a global scale in the Devonian-Carboniferous (D-C) boundary interval, which records one of the largest Phanerozoic mass-extinction events, an event that devastated many groups of living organisms, such as plants, ammonoids, trilobites, conodonts, fish, foraminiferans, brachiopods, and ostracodes. At or very close to the D-C boundary, there exists a geographically widespread black-shale interval, and Ir abundances reach anomalous maxima of 0.148 ppb (Montagne Noire, France), 0.138 ppb (Alberta, Canada) 0.140 ppb (Carnic Alps, Austria), 0.156 ppb (Guangxi, China), 0.258 ppb (Guizhou, China), and 0.250 ppb (Oklahoma). The discovery of global D-C Ir anomalies argues for an impact-extinction model. However, nonchondritic ratios of Ir to other important elements and a lack of physical evidence (shocked quartz, microtektites) do not support such a scenario. The fact that all Ir abundance maxima are at sharp redox boundaries in these sections leads us to conclude that the Ir anomalies likely resulted from a sudden change in paleo-redox conditions during deposition and/or early diagenesis. 36 refs., 2 figs., 1 tab.

Hydrogeologic characterization of devonian aquifers in Uruguay

International Nuclear Information System (INIS)

Massa, E.

1988-01-01

This article carried out the assistance research project implementation in devonian sedimentary units as a potentials aquifers and their best use to school supplying and rural population in central area of Uruguay.

Association between catastrophic paleovegetation changes during Devonian-Carboniferous boundary and the formation of giant massive sulfide deposits

Science.gov (United States)

Menor-Salván, Cesar; Tornos, Fernando; Fernández-Remolar, David; Amils, Ricardo

2010-11-01

The Iberian Pyrite Belt (SW Iberia) is one of the largest sulfur anomalies in the Earth's crust. In the southern Iberian Pyrite Belt, more than 820 Mt of exhalative massive sulfides were deposited in less than one million years at the Devonian-Carboniferous boundary. The shale of the ore-bearing horizon contains biomarkers indicating major biogenic activity in a methanogenic setting, including a five-fold increase in typical vascular plant biomarkers and a significant anomaly in those probably indicating the presence of thermophilic Archaea. This contrasts with signatures in the average sedimentary rocks of the basin that indicate the sediments settled in oxic to sub-oxic environments, and that they have only minor biomarkers derived from continental paleoflora. These data show that the formation of the mineralization was not only related to major hydrothermal activity synchronous with volcanism but may also have been controlled by the input of large amounts of organic matter, mostly derived from the degradation of woodland detritus sourced in the nearby continent. This massive influx of organic matter could have accelerated extremophilic microbial activity that used short-chain hydrocarbons as electron donors for seawater sulfate reduction, resulting in concomitant massive sulfide precipitation. We propose that the giant massive sulfide deposits resulted from overlapping of geological and biological processes that occurred at the Devonian to Carboniferous transition, including: (1) continent collision during the onset of the Variscan orogeny leading to major paleogeographic changes and volcanism; (2) dramatic stress of continental ecosystems due to the combination of climatic change, volcanism, variations in the sea level and erosion on a regional scale; (3) major biomass destruction and increase of organic supply to marine environments; and, (4) generation of anoxic conditions and the thriving of sulfate reducing microorganisms. Under these conditions, massive

Sequence stratigraphy from ``spot'' outcrops—example from a carbonate-dominated setting: Devonian-Carboniferous transition, Dinant synclinorium (Belgium)

Science.gov (United States)

Van Steenwinkel, M.

1990-12-01

-level rise (5). The associated offshore shales are the deepest facies recorded. They are capped by a prograding unit deposited during a relative highstand (6). The reconstruction of a relative sea-level curve and the subsequent determination of the bounding surfaces, is not only the key to understanding the Devonian-Carboniferous stratigraphy but also a tool for lateral correlation of "spot" outcrops.

Geology of redbed Cu-U occurrences in the Upper Devonian Catskill Fm., Pennsylvania

International Nuclear Information System (INIS)

Smith, A.T.

1983-01-01

A regional and detailed geologic, petrographic and geochemical study of 40 redbed Cu-U occurrences and the host Upper Devonian Catskill Fm. in Pennsylvania shows that depositional environment and diagenetic processes were the most important controls on the formation of the occurrences. The Catskill Fm. in Pa. has been divided into 4 magnafacies (Mf). In ascending order, Mf-A contains interbedded marine and non-marine shale and fine sandstones; Mf-B contains mainly thick red shales and thin sandstones interpreted to be low-energy fluvial deposits on an inactive coastal plain interrupted by occasional thin transgressive marine sandstones. Mf-C is composed of thick sandstones deposited by braided rivers; and Mf-D is composed of thick fining-up cycles deposited by meandering rivers. The Cu-U occurrences are located in areas of thick Mf-B; they occur in Mf-A, -B and -D. Cu-sulfides formed during diagenesis with chlorite in pockets of plant trash within or below a marine or fluvial sandstones, which contain a greater percentage of ductile grains than similar sandstones are inferred to have been more permeable than non-mineralized sandstones. The Cu-sulfides formed after early hematite, clay coatings and calcite cement. Based on isotopic, textural and compositional evidence, the calcite is considered to have formed near the surface at temperatures of less than 100 0 C from oxidizing waters reduced by plant material. The Cu and U in a typical occurrence could easily have been derived by leaching of 1-3% of the total Cu and U from a volume of sediment equivalent to a cube of 40 m or less on a side. Cu appears to have been mobilized during compaction and was derived from the fine fraction of the sediments by Cl-bearing solutions introduced during marine transgressions

Late Paleozoic SEDEX deposits in South China formed in a carbonate platform at the northern margin of Gondwana

Science.gov (United States)

Qiu, Wenhong Johnson; Zhou, Mei-Fu; Liu, Zerui Ray

2018-05-01

SEDEX sulfide deposits hosted in black shale and carbonate are common in the South China Block. The Dajiangping pyrite deposit is the largest of these deposits and is made up of stratiform orebodies hosted in black shales. Sandstone interlayered with stratiform orebodies contains detrital zircon grains with the youngest ages of 429 Ma. Pyrite from the orebodies has a Re-Os isochron age of 389 ± 62 Ma, indicative of formation of the hosting strata and syngenetic pyrite ores in the mid-late Devonian. The hosting strata is a transgression sequence in a passive margin and composed of carbonaceous limestone in the lower part and black shales in the upper part. The ore-hosting black shales have high TOC (total organic carbon), Mo, As, Pb, Zn and Cd, indicating an anoxic-euxinic deep basin origin. The high redox proxies, V/(V + Ni) > 0.6 and V/Cr > 1, and the positive correlations of TOC with Mo and V in black shales are also consistent with an anoxic depositional environment. The Dajiangping deposit is located close to the NE-trending Wuchuan-Sihui fault, which was active during the Devonian. The mid-late Devonian mineralization age and the anoxic-euxinic deep basinal condition of this deposit thus imply that the formation of this deposit was causally linked to hydrothermal fluid exhalation in an anoxic fault-bounded basin that developed in a carbonate platform of the South China Block. The regional distribution of many Devonian, stratiform, carbonaceous sediment-hosted sulfide deposits along the NE-trending fault-bounded basins in South China, similar to the Dajiangping deposit, indicates that these deposits formed at a basin developed in the passive margin setting of the South China Block during the Devonian. This environment was caused by the break-up and northward migration of the South China Block from Gandwana.

Introduction to special section: China shale gas and shale oil plays

Science.gov (United States)

Jiang, Shu; Zeng, Hongliu; Zhang, Jinchuan; Fishman, Neil; Bai, Baojun; Xiao, Xianming; Zhang, Tongwei; Ellis, Geoffrey S.; Li, Xinjing; Richards-McClung, Bryony; Cai, Dongsheng; Ma, Yongsheng

2015-01-01

In the last 10 years, the success of shale gas and shale oil productions as a result of technological advances in horizontal drilling, hydraulic fracturing and nanoscale reservoir characterization have revolutionized the energy landscape in the United States. Resource assessment by the China Ministry of Land and Resources in 2010 and 2012 and by the U.S. Energy Information Administration in 2011 and 2013 indicates China’s shale gas resource is the largest in the world and shale oil resource in China is also potentially significant. Inspired by the success in the United States, China looks forward to replicating the U.S. experience to produce shale gas to power its economy and reduce greenhouse gas emissions. By 2014, China had drilled 400 wells targeting marine, lacustrine, and coastal swamp transitional shales spanning in age from the Precambrian to Cenozoic in the last five years. So far, China is the leading country outside of North America in the viable production of shale gas, with very promising prospects for shale gas and shale oil development, from the Lower Silurian Longmaxi marine shale in Fuling in the southeastern Sichuan Basin. Geological investigations by government and academic institutions as well as exploration and production activities from industry indicate that the tectonic framework, depositional settings, and geomechanical properties of most of the Chinese shales are more complex than many of the producing marine shales in the United States. These differences limit the applicability of geologic analogues from North America for use in Chinese shale oil and gas resource assessments, exploration strategies, reservoir characterization, and determination of optimal hydraulic fracturing techniques. Understanding the unique features of the geology, shale oil and gas resource potential, and reservoir characteristics is crucial for sweet spot identification, hydraulic fracturing optimization, and reservoir performance prediction.

Provenance and paleogeography of the Devonian Durazno Group, southern Parana Basin in Uruguay

Science.gov (United States)

Uriz, N. J.; Cingolani, C. A.; Basei, M. A. S.; Blanco, G.; Abre, P.; Portillo, N. S.; Siccardi, A.

2016-03-01

A succession of Devonian cover rocks occurs in outcrop and in the subsurface of central-northern Uruguay where they were deposited in an intracratonic basin. This Durazno Group comprises three distinct stratigraphic units, namely the Cerrezuelo, Cordobés and La Paloma formations. The Durazno Group does not exceed 300 m of average thickness and preserves a transgressive-regressive cycle within a shallow-marine siliciclastic shelf platform, and is characterized by an assemblage of invertebrate fossils of Malvinokaffric affinity especially within the Lower Devonian Cordobés shales. The sedimentary provenance of the Durazno Group was determined using petrography, geochemistry, and morphological studies of detrital zircons as well as their U-Pb ages. Sandstone petrography of Cerrezuelo and La Paloma sequences shows that they have a dominantly quartz-feldspathic composition with a minor contribution of other minerals. Whole-rock geochemical data indicate that alteration was strong in each of the three formations studied; chondritic-normalized REE patterns essentially parallel to PAAS, the presence of a negative Eu-anomaly, and Th/Sc and La/Hf ratios point to an average source composition similar to UCC or slightly more felsic. Within the Cerrezuelo Formation, recycling of older volcano-metasedimentary sources is interpreted from Zr/Sc ratios and high Hf, Zr, and REE concentrations. U-Pb detrital zircon age populations of the Cerrezuelo and La Paloma formations indicate that the principal source terranes are of Neoproterozoic age, but include also minor populations derived from Mesoproterozoic and Archean-Paleoproterozoic rocks. A provenance from the Cuchilla Dionisio-Dom Feliciano, Nico Pérez and Piedra Alta terranes of Uruguay and southern Brazil is likely. This study establishes an intracratonic extensional tectonic setting during Durazno time. Considering provenance age sources, regional paleocurrent distributions and the established orogenic history recorded in SW

Study seeks to boost Appalachian gas recovery

International Nuclear Information System (INIS)

Land, R.

1992-01-01

Ashland Exploration Inc. and the Gas Research Institute (GRI) are trying to find ways to increase gas recovery in the Appalachian basin. They are working together to investigate Mississippian Berea sandstone and Devonian shale in a program designed to achieve better understanding and improved performance of tight natural gas formations in the area. This paper reports that three wells on Ashland Exploration acreage in Pike County, Ky., are involved in the research program. Findings from the first two wells will be used to optimize evaluation and completion of the third well. The first two wells have been drilled. Drilling of the third well was under way at last report. Ashland Exploration has been involved with GRI's Devonian shale research since 1988. GRI's initial focus was on well stimulation because Devonian shale wells it reviewed had much lower recoveries than could be expected, based on estimated gas in place. Research during the past few years was designed to improve the execution and quality control of well stimulation

Weathering of the New Albany Shale, Kentucky: II. Redistribution of minor and trace elements

Science.gov (United States)

Tuttle, M.L.W.; Breit, G.N.; Goldhaber, M.B.

2009-01-01

During weathering, elements enriched in black shale are dispersed in the environment by aqueous and mechanical transport. Here a unique evaluation of the differential release, transport, and fate of Fe and 15 trace elements during progressive weathering of the Devonian New Albany Shale in Kentucky is presented. Results of chemical analyses along a weathering profile (unweathered through progressively weathered shale to soil) describe the chemically distinct pathways of the trace elements and the rate that elements are transferred into the broader, local environment. Trace elements enriched in the unweathered shale are in massive or framboidal pyrite, minor sphalerite, CuS and NiS phases, organic matter and clay minerals. These phases are subject to varying degrees and rates of alteration along the profile. Cadmium, Co, Mn, Ni, and Zn are removed from weathered shale during sulfide-mineral oxidation and transported primarily in aqueous solution. The aqueous fluxes for these trace elements range from 0.1 g/ha/a (Cd) to 44 g/ha/a (Mn). When hydrologic and climatic conditions are favorable, solutions seep to surface exposures, evaporate, and form Fe-sulfate efflorescent salts rich in these elements. Elements that remain dissolved in the low pH (pH. Neutralization of the weathering solution in local streams results in elements being adsorbed and precipitated onto sediment surfaces, resulting in trace element anomalies. Other elements are strongly adsorbed or structurally bound to solid phases during weathering. Copper and U initially are concentrated in weathering solutions, but become fixed to modern plant litter in soil formed on New Albany Shale. Molybdenum, Pb, Sb, and Se are released from sulfide minerals and organic matter by oxidation and accumulate in Fe-oxyhydroxide clay coatings that concentrate in surface soil during illuviation. Chromium, Ti, and V are strongly correlated with clay abundance and considered to be in the structure of illitic clay. Illite

Oil shale technology

International Nuclear Information System (INIS)

Lee, S.

1991-01-01

Oil shale is undoubtedly an excellent energy source that has great abundance and world-wide distribution. Oil shale industries have seen ups and downs over more than 100 years, depending on the availability and price of conventional petroleum crudes. Market forces as well as environmental factors will greatly affect the interest in development of oil shale. Besides competing with conventional crude oil and natural gas, shale oil will have to compete favorably with coal-derived fuels for similar markets. Crude shale oil is obtained from oil shale by a relatively simple process called retorting. However, the process economics are greatly affected by the thermal efficiencies, the richness of shale, the mass transfer effectiveness, the conversion efficiency, the design of retort, the environmental post-treatment, etc. A great many process ideas and patents related to the oil shale pyrolysis have been developed; however, relatively few field and engineering data have been published. Due to the vast heterogeneity of oil shale and to the complexities of physicochemical process mechanisms, scientific or technological generalization of oil shale retorting is difficult to achieve. Dwindling supplied of worldwide petroleum reserves, as well as the unprecedented appetite of mankind for clean liquid fuel, has made the public concern for future energy market grow rapidly. the clean coal technology and the alternate fuel technology are currently of great significance not only to policy makers, but also to process and chemical researchers. In this book, efforts have been made to make a comprehensive text for the science and technology of oil shale utilization. Therefore, subjects dealing with the terminological definitions, geology and petrology, chemistry, characterization, process engineering, mathematical modeling, chemical reaction engineering, experimental methods, and statistical experimental design, etc. are covered in detail

Secular distribution of highly metalliferous black shales corresponds with peaks in past atmosphere oxygenation

Science.gov (United States)

Johnson, Sean C.; Large, Ross R.; Coveney, Raymond M.; Kelley, Karen D.; Slack, John F.; Steadman, Jeffrey A.; Gregory, Daniel D.; Sack, Patrick J.; Meffre, Sebastien

2017-08-01

Highly metalliferous black shales (HMBS) are enriched in organic carbon and a suite of metals, including Ni, Se, Mo, Ag, Au, Zn, Cu, Pb, V, As, Sb, Se, P, Cr, and U ± PGE, compared to common black shales, and are distributed at particular times through Earth history. They constitute an important future source of metals. HMBS are relatively thin units within thicker packages of regionally extensive, continental margin or intra-continental marine shales that are rich in organic matter and bio-essential trace elements. Accumulation and preservation of black shales, and the metals contained within them, usually require low-oxygen or euxinic bottom waters. However, whole-rock redox proxies, particularly Mo, suggest that HMBS may have formed during periods of elevated atmosphere pO2. This interpretation is supported by high levels of nutrient trace elements within these rocks and secular patterns of Se and Se/Co ratios in sedimentary pyrite through Earth history, with peaks occurring in the middle Paleoproterozoic, Early Cambrian to Early Ordovician, Middle Devonian, Middle to late Carboniferous, Middle Permian, and Middle to Late Cretaceous, all corresponding with time periods of HMBS deposition. This counter-intuitive relationship of strongly anoxic to euxinic, localized seafloor conditions forming under an atmosphere of peak oxygen concentrations is proposed as key to the genesis of HMBS. The secular peaks and shoulders of enriched Se in sedimentary pyrite through time correlate with periods of tectonic plate collision, which resulted in high nutrient supply to the oceans and consequently maximum productivity accompanying severe drawdown into seafloor muds of C, S, P, and nutrient trace metals. The focused burial of C and S over extensive areas of the seafloor, during these anoxic to euxinic periods, likely resulted in an O2 increase in the atmosphere, causing short-lived peaks in pO2 that coincide with the deposition of HMBS. As metals become scarce, particularly Mo

Sediment Sources, Depositional Environment, and Diagenetic Alteration of the Marcellus Shale, Appalachian Basin, USA: Nd, Sr, Li and U Isotopic Constraints

Science.gov (United States)

Phan, T. T.; Capo, R. C.; Gardiner, J. B.; Stewart, B. W.

2017-12-01

The organic-rich Middle Devonian Marcellus Shale in the Appalachian Basin, eastern USA, is a major target of natural gas exploration. Constraints on local and regional sediment sources, depositional environments, and post-depositional processes are essential for understanding the evolution of the basin. In this study, multiple proxies, including trace metals, rare earth elements (REE), the Sm-Nd and Rb-Sr isotope systems, and U and Li isotopes were applied to bulk rocks and authigenic fractions of the Marcellus Shale and adjacent limestone/sandstone units from two locations separated by 400 km. The range of ɛNd values (-7.8 to -6.4 at 390 Ma) is consistent with a clastic sedimentary component derived from a well-mixed source of fluvial and eolian material of the Grenville orogenic belt. The Sm-Nd isotope system and bulk REE distributions appear to have been minimally affected by post-depositional processes, while the Rb-Sr isotope system shows evidence of limited post-depositional redistribution. While REE are primarily associated with silicate minerals (80-95%), REE patterns of sequentially extracted fractions reflect post-depositional alteration at the intergranular scale. Although the chemical index of alteration (CIA = 54 to 60) suggests the sediment source was not heavily weathered, Li isotope data are consistent with progressively increasing weathering of the source region during Marcellus Shale deposition. δ238U values in bulk shale and reduced phases (oxidizable fraction) are higher than those of modern seawater and upper crust. The isotopically heavy U accumulated in these authigenic phases can be explained by the precipitation of insoluble U in anoxic/euxinic bottom water. Unlike carbonate cement within the shale, the similarity between δ238U values and REE patterns of the limestone units and those of modern seawater indicates that the limestone formed under open ocean (oxic) conditions.

The axial skeleton of the Devonian tetrapod Ichthyostega.

Science.gov (United States)

Ahlberg, Per Erik; Clack, Jennifer A; Blom, Henning

2005-09-01

Ichthyostega was the first Devonian tetrapod to be subject to a whole-body reconstruction. It remains, together with Acanthostega, one of only two Devonian tetrapods for which near-complete postcranial material is available. It is thus crucially important for our understanding of the earliest stages of tetrapod evolution and terrestrialization. Here we show a new reconstruction of Ichthyostega based on extensive re-examination of original material and augmented by recently collected specimens. Our reconstruction differs substantially from those previously published and reveals hitherto unrecognized regionalization in the vertebral column. Ichthyostega is the earliest vertebrate to show obvious adaptations for non-swimming locomotion. Uniquely among early tetrapods, the presacral vertebral column shows pronounced regionalization of neural arch morphology, suggesting that it was adapted for dorsoventral rather than lateral flexion.

Barnett shale completions

Energy Technology Data Exchange (ETDEWEB)

Schein, G. [BJ Services, Dallas, TX (United States)

2006-07-01

Fractured shales yield oil and gas in various basins across the United States. A map indicating these fractured shale source-reservoir systems in the United States was presented along with the numerous similarities and differences that exist among these systems. Hydrocarbons in the organic rich black shale come from the bacterial decomposition of organic matter, primary thermogenic decomposition of organic matter or secondary thermogenic cracking of oil. The shale may be the reservoir or other horizons may be the primary or secondary reservoir. The reservoir has induced micro fractures or tectonic fractures. This paper described the well completions in the Barnett Shale in north Texas with reference to major players, reservoir properties, mineralogy, fluid sensitivity, previous treatments, design criteria and production examples. The Barnett Shale is an organic, black shale with thickness ranging from 100 to 1000 feet. The total organic carbon (TOC) averages 4.5 per cent. The unit has undergone high rate frac treatments. A review of the vertical wells in the Barnett Shale was presented along with the fracture treatment schedule and technology changes. A discussion of refracturing opportunities and proppant settling and transport revealed that additional proppant increases fluid recovery and enhances production. Compatible scale inhibitors and biocides can be beneficial. Horizontal completions in the Barnett Shale have shown better results than vertical wells, as demonstrated in a production comparison of 3 major horizontal wells in the basin. tabs., figs.

Devonian alkaline magmatic belt along the northern margin of the North China Block: Petrogenesis and tectonic implications

Science.gov (United States)

Zhang, Qi-Qi; Zhang, Shuan-Hong; Zhao, Yue; Liu, Jian-Min

2018-03-01

Some Devonian magmatic rocks have been identified from the northern margin of the North China Block (NCB) in recent years. However, their petrogenesis and tectonic setting are still highly controversial. Here we present new geochronological, Sr-Nd-Hf isotopic and whole-rock chemical data on several newly identified and previously reported Devonian alkaline complexes, including mafic-ultramafic rocks (pyroxenites and gabbros), alkaline rocks (syenites, monzonites) and alkaline granites in the northern NCB. We firstly identified some mafic-ultramafic rocks coeval with monzonite and quartz monzonite in the Sandaogou and Wulanhada alkaline intrusions. New zircon U-Pb dating of 16 samples from the Baicaigou, Gaojiacun, Sandaogou, Wulanhada and Chifeng alkaline intrusions combined with previous geochronological results indicate that the Devonian alkaline rocks emplaced during the early-middle Devonian at around 400-380 Ma and constitute an E-W-trending alkaline magmatic belt that extend ca. 900 km long along the northern margin of the NCB. Whole-rock geochemical and Sr-Nd-Hf isotopic data reveal that the Devonian alkaline rocks were mainly originated from partial melting of a variably enriched lithospheric mantle with different involvement of ancient lower crustal component and fractional crystallization. The Devonian alkaline magmatic belt rocks in the northern NCB are characterized by very weak or no deformations and were most likely related to post-collision extension after arc-continent collision between the Bainaimiao island arc and the northern margin of North China Craton during the latest Silurian. Partial melting of subcontinental lithospheric mantle to produce the Devonian alkaline magmatic rocks suggests that the northern North China Craton has an inhomogeneous, variably enriched subcontinental lithospheric mantle and was characterized by significant vertical crustal growth during the Devonian period.

Oil shale activities in China

International Nuclear Information System (INIS)

Peng, D.; Jialin, Q.

1991-01-01

China has abundant oil shale resources, of the Early Silurian to Neogene age, the most important being the Tertiary period. The proved oil shale reserves in Fushun amount to 3.6 billion t, in Maoming 4.1 billion t. In Fushun, oil shale is produced by open-pit mining as a byproduct of coal, in Maoming it is also mined in open pits, but without coal. In China, scale oil has been produced from oil shale for 60 years. Annual production of crude shale oil amounts to about 200 000 t. The production costs of shale oil are lower than the price of crude petroleum on the world market. China has accumulated the experience and technologies of oil shale retorting. The Fushun type retort has been elaborated, in which the latent and sensible heat of shale coke is well utilized. But the capacity of such retort is relatively small, therefore it is suitable for use in small or medium oil plants. China has a policy of steadily developing shale oil industry. China is conducting oil shale research and developing oil shale processing technology. Much attention is being pay ed to the comprehensive utilization of oil shale, shale oil, and to environmental problems. In China, oil shale is mostly used for producing shale by retorting, attention will also be paid to direct combustion for power generation. Great achievements in oil shale research have been made in the eighties, and there will be a further development in the nineties. (author), 12 refs., 3 tabs

Seawater strontium isotope curve at the Silurian/Devonian boundary: a study of the global Silurian/Devonian boundary stratotype

Czech Academy of Sciences Publication Activity Database

Frýda, J.; Hladil, Jindřich; Vokurka, K.

2002-01-01

Roč. 35, č. 1 (2002), s. 21-28 ISSN 0016-6995 R&D Projects: GA ČR GA205/98/0454; GA ČR GA205/01/0143 Institutional research plan: CEZ:AV0Z3013912 Keywords : strontium chemostratigraphy * Silurian/Devonian * Barrandian area Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.410, year: 2002

Climate effects caused by land plant invasion in the Devonian

Science.gov (United States)

Hir guillaume, Le; yannick, Donnadieu; yves, Goddéris; brigitte, Meyer-Berthaud; gilles, Ramstein

2017-04-01

Land plants invaded continents during the Mid-Paleozoic. Their spreading and diversification have been compared to the Cambrian explosion in terms of intensity and impact on the diversification of life on Earth. Whereas prior studies were focused on the evolution of the root system and its weathering contribution, here we investigated the biophysical impacts of plant colonization on the surface climate through changes in continental albedo, roughness, thermal properties, and potential evaporation using a 3D-climate model coupled to a global biogeochemical cycles associated to a simple model for vegetation dynamics adapted to Devonian conditions. From the Early to the Late Devonian, we show that continental surface changes induced by land plants and tectonic drift have produced a large CO2 drawdown without being associated to a global cooling, because the cooling trend is counteracted by a warming trend resulting from the surface albedo reduction. If CO2 is consensually assumed as the main driver of the Phanerozoic climate, during land-plant invasion, the modifications of soil properties could have played in the opposite direction of the carbon dioxide fall, hence maintaining warm temperatures during part of the Devonian.

Chemical aspects of shale and shale oils

Energy Technology Data Exchange (ETDEWEB)

Hackford, J E

1922-01-01

To prove that the kerogen in oil shale is a form of bitumen, several experiments were made with oil shale and a heavy asphaltic oil mixed with fuller's earth. When distilled, both the oil shale and asphalt-impregnated fuller's earth yielded paraffin oil, wax, and hydrogen sulfide (if sulfur was present). Both yielded ammonia if nitrogen was present. The organic material in each was partly isolated by extraction with pyridine and appeared to be the same. Oil shale is a marl that was saturated with oil or through which oil has passed or filtered. The insolubilities of its organic compounds are due to a slightly elevated temperature for a prolonged period and to the retaining effect exerted by the finely divided marl. The marl exerted a selective action on the oil and absorbed the asphaltum, sulfur, and nitrogen compounds from the oil. The class of oil evolved from a shale depended on the nature of the original compounds absorbed. Asphaltenes obtained from crude oil by precipitation with ethyl ether produced distillation products of water, hydrogen sulfide, ammonia, oil, wax, and a carbonaceous residue. Water was formed by decomposition of oxyasphaltenes and hydrogen sulfide by decomposition of thioasphaltenes. Ammonia was evolved during decomposition if lime was present, but if there was not sufficient free lime present, pyridine and pyrrole derivatives were redistilled as such. The oil and wax that resulted from the dry distillation were true decomposition products and equaled about 60 weight-percent of the asphaltenes. The oil and wax content of the mixture varied between 8 and 10 percent. The carbonaceous residue, which represented approximately 40 percent of the original asphaltene, was a decomposition product of the asphaltenes. Geologic comparisons of oil-shale deposits and oil-well fields were also made.

Radiometric evidence of Middle Devonian inversion of the Hill End Trough, northeast Lachlan Fold Belt

International Nuclear Information System (INIS)

Pakham, G.H.

1999-01-01

The publication of a new geological time-scale by the Australian Geological Survey Organisation and radiometric dates from the Hill End goldfield have prompted the re-examination of the timing of deformation of the Hill End Trough to determine whether it occurred in Middle Devonian or Early Carboniferous time. Palaeontological evidence from the western trough margin and the Capertee High dates the end of deposition in the trough as late Emsian or early Eifelian (385-382 Ma). After a mid-Devonian hiatus of at least 15 million years, paralic sedimentation commenced on the Molong and Capertee Highs in late Frasnian or early Famennian time (367-363 Ma). No Upper Devonian sedimentary formations occur in the Hill End Trough. Structural relationships indicate that the oldest mineral veins at Hill End preceded cleavage formation in the deformed trough sedimentary rocks. Early vein muscovites have Middle Devonian 40 Ar/ 39 Ar dates of 380-370 Ma. Regional metamorphic biotites from Hill End have well constrained 40 Ar/ 39 Ar closing ages of 360-358 Ma (mid-Famennian). The metamorphic (thermal) maximum which outlasted penetrative deformation. is estimated here by modelling to have been about 370 Ma (latest Givetian). This clearly places the earlier main deformation in the Middle Devonian. Deformation probably began by terminating trough deposition in latest Emsian to early Eifelian time and ended in early Givetian time at about 375 Ma ago. Published pressure and temperature data from the Hill End goldfield suggest that deformation thickened the 6 km sediment column to around 11 km. The thermal model suggests there was post-deformation erosion of about 4km and little if any further erosion occurred during Late Devonian to Early Carboniferous time. The shortening accompanying the inversion of the northern Hill End Trough may have been taken up in the region to the south, both east and west of the Copperhannia Thrust, and east of the southern termination of the Capertee High

Shale oil. II. Gases from oil shale

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil shale (from Colorado) was pyrolyzed, and the gaseous products obtained were studied. The organic material present in oil shale contains carboxyl groups that lose carbon dioxide during pyrolysis before the formation of soluble bitumen. Nitrogen was evolved as ammonia in two stages and was not continuous. The first evolution was from loosely combined nitrogen structures, whereas the second was from more stable forms. No hydrocarbons were present as such in the kerogen. The gaseous products from oil-shale pyrolysis were similar to those obtained by distillation of colophony, amber, coal, and wood. This places the kerogen of the oil shale in the same series of carbonaceous substances as those from which coals are formed. Kerogen appeared to be decomposed in three steps; namely, to insoluble bitumen, to soluble bitumen, and to oil (gas evolution accompanied each step). Its low solubility and the character of its pyrolytic gas indicated that kerogen is largely a resinous residue from vegetation of the past era and may have been formed by the tranportation of coal-forming organic debris to inland salty lakes or carried to the sea by clay-laden waters. The salt water and the natural settling action precipitated the clay and organic matter in an almost homogeneous deposit. Oil shales have existed to the present time because they have not been subjected to high pressures or elevated temperatures that would have changed them to petroleum.

Oil shale commercialization study

Energy Technology Data Exchange (ETDEWEB)

Warner, M.M.

1981-09-01

Ninety four possible oil shale sections in southern Idaho were located and chemically analyzed. Sixty-two of these shales show good promise of possible oil and probable gas potential. Sixty of the potential oil and gas shales represent the Succor Creek Formation of Miocene age in southwestern Idaho. Two of the shales represent Cretaceous formations in eastern Idaho, which should be further investigated to determine their realistic value and areal extent. Samples of the older Mesozonic and paleozoic sections show promise but have not been chemically analyzed and will need greater attention to determine their potential. Geothermal resources are of high potential in Idaho and are important to oil shale prospects. Geothermal conditions raise the geothermal gradient and act as maturing agents to oil shale. They also might be used in the retorting and refining processes. Oil shales at the surface, which appear to have good oil or gas potential should have much higher potential at depth where the geothermal gradient is high. Samples from deep petroleum exploration wells indicate that the succor Creek shales have undergone considerable maturation with depth of burial and should produce gas and possibly oil. Most of Idaho's shales that have been analyzed have a greater potential for gas than for oil but some oil potential is indicated. The Miocene shales of the Succor Creek Formation should be considered as gas and possibly oil source material for the future when technology has been perfectes. 11 refs.

Porosity of the Marcellus Shale: A contrast matching small-angle neutron scattering study

Science.gov (United States)

Bahadur, Jitendra; Ruppert, Leslie F.; Pipich, Vitaliy; Sakurovs, Richard; Melnichenko, Yuri B.

2018-01-01

Neutron scattering techniques were used to determine the effect of mineral matter on the accessibility of water and toluene to pores in the Devonian Marcellus Shale. Three Marcellus Shale samples, representing quartz-rich, clay-rich, and carbonate-rich facies, were examined using contrast matching small-angle neutron scattering (CM-SANS) at ambient pressure and temperature. Contrast matching compositions of H2O, D2O and toluene, deuterated toluene were used to probe open and closed pores of these three shale samples. Results show that although the mean pore radius was approximately the same for all three samples, the fractal dimension of the quartz-rich sample was higher than for the clay-rich and carbonate-rich samples, indicating different pore size distributions among the samples. The number density of pores was highest in the clay-rich sample and lowest in the quartz-rich sample. Contrast matching with water and toluene mixtures shows that the accessibility of pores to water and toluene also varied among the samples. In general, water accessed approximately 70–80% of the larger pores (>80 nm radius) in all three samples. At smaller pore sizes (~5–80 nm radius), the fraction of accessible pores decreases. The lowest accessibility to both fluids is at pore throat size of ~25 nm radii with the quartz-rich sample exhibiting lower accessibility than the clay- and carbonate-rich samples. The mechanism for this behaviour is unclear, but because the mineralogy of the three samples varies, it is likely that the inaccessible pores in this size range are associated with organics and not a specific mineral within the samples. At even smaller pore sizes (~generally follows that of water; however, in the smallest pores (~<2.5 nm radius), accessibility to toluene decreases, especially in the clay-rich sample which contains about 30% more closed pores than the quartz- and carbonate-rich samples. Results from this study show that mineralogy of producing intervals

Geochemical and multi-isotopic (87Sr/86Sr, 143Nd/144Nd, 238U/235U) perspectives of sediment sources, depositional conditions, and diagenesis of the Marcellus Shale, Appalachian Basin, USA

Science.gov (United States)

Phan, Thai T.; Gardiner, James B.; Capo, Rosemary C.; Stewart, Brian W.

2018-02-01

We investigate sediment sources, depositional conditions and diagenetic processes affecting the Middle Devonian Marcellus Shale in the Appalachian Basin, eastern USA, a major target of natural gas exploration. Multiple proxies, including trace metal contents, rare earth elements (REE), the Sm-Nd and Rb-Sr isotope systems, and U isotopes were applied to whole rock digestions and sequentially extracted fractions of the Marcellus shale and adjacent units from two locations in the Appalachian Basin. The narrow range of εNd values (from -7.8 to -6.4 at 390 Ma) is consistent with derivation of the clastic sedimentary component of the Marcellus Shale from a well-mixed source of fluvial and eolian material of the Grenville orogenic belt, and indicate minimal post-depositional alteration of the Sm-Nd system. While silicate minerals host >80% of the REE in the shale, data from sequentially extracted fractions reflect post-depositional modifications at the mineralogical scale, which is not observed in whole rock REE patterns. Limestone units thought to have formed under open ocean (oxic) conditions have δ238U values and REE patterns consistent with modern seawater. The δ238U values in whole rock shale and authigenic phases are greater than those of modern seawater and the upper crust. The δ238U values of reduced phases (the oxidizable fraction consisting of organics and sulfide minerals) are ∼0.6‰ greater than that of modern seawater. Bulk shale and carbonate cement extracted from the shale have similar δ238U values, and are greater than δ238U values of adjacent limestone units. We suggest these trends are due to the accumulation of chemically and, more likely, biologically reduced U from anoxic to euxinic bottom water as well as the influence of diagenetic reactions between pore fluids and surrounding sediment and organic matter during diagenesis and catagenesis.

Sedimentary processes and depositional environments of the Horn River Shale in British Columbia, Canada

Science.gov (United States)

Yoon, Seok-Hoon; Koh, Chang-Seong; Joe, Young-Jin; Woo, Ju-Hwan; Lee, Hyun-Suk

2017-04-01

The Horn River Basin in the northeastern British Columbia, Canada, is one of the largest unconventional gas accumulations in North America. It consists mainly of Devonian shales (Horn River Formation) and is stratigraphically divided into three members, the Muskwa, Otterpark and Evie in descending order. This study focuses on sedimentary processes and depositional environments of the Horn River shale based on sedimentary facies analysis aided by well-log mineralogy (ECS) and total organic carbon (TOC) data. The shale formation consists dominantly of siliceous minerals (quartz, feldspar and mica) and subordinate clay mineral and carbonate materials, and TOC ranging from 1.0 to 7.6%. Based on sedimentary structures and micro texture, three sedimentary facies were classified: homogeneous mudstone (HM), indistinctly laminated mudstone (ILM), and planar laminated mudstone (PLM). Integrated interpretation of the sedimentary facies, lithology and TOC suggests that depositional environment of the Horn River shale was an anoxic quiescent basin plain and base-of-slope off carbonate platform or reef. In this deeper marine setting, organic-rich facies HM and ILM, dominant in the Muskwa (the upper part of the Horn River Formation) and Evie (the lower part of the Horn River Formation) members, may have been emplaced by pelagic to hemipelagic sedimentation on the anoxic sea floor with infrequent effects of low-density gravity flows (turbidity currents or nepheloid flows). In the other hand, facies PLM typifying the Otterpark Member (the middle part of the Horn River Formation) suggests more frequent inflow of bottom-hugging turbidity currents punctuating the hemipelagic settling of the background sedimentation process. The stratigraphic change of sedimentary facies and TOC content in the Horn River Formation is most appropriately interpreted to have been caused by the relative sea-level change, that is, lower TOC and frequent signal of turbidity current during the sea

Process for retorting shale

Energy Technology Data Exchange (ETDEWEB)

1952-03-19

The method of retorting oil shale to recover valuable liquid and gaseous hydrocarbons consists of heating the oil shale in a retorting zone to a temperature sufficient to convert its kerogenic constituents to normally liquid and normally gaseous hydrocarbons by contact with hot gas previously recovered from shale, cooling the gases and vapors effluent from the retorting zone by direct countercurrent contact with fresh shale to condense the normally liquid constituents of the gases and vapors, separating the fixed gas from the liquid product, heating the fixed gas, and returning it to the retorting zone to contact further quantities of shale.

Devonian magmatism in the Timan Range, Arctic Russia - subduction, post-orogenic extension, or rifting?

Science.gov (United States)

Pease, V.; Scarrow, J. H.; Silva, I. G. Nobre; Cambeses, A.

2016-11-01

Devonian mafic magmatism of the northern East European Craton (EEC) has been variously linked to Uralian subduction, post-orogenic extension associated with Caledonian collision, and rifting. New elemental and isotopic analyses of Devonian basalts from the Timan Range and Kanin Peninsula, Russia, in the northern EEC constrain magma genesis, mantle source(s) and the tectonic process(es) associated with this Devonian volcanism to a rift-related context. Two compositional groups of low-K2O tholeiitic basalts are recognized. On the basis of Th concentrations, LREE concentrations, and (LREE/HREE)N, the data suggest two distinct magma batches. Incompatible trace elements ratios (e.g., Th/Yb, Nb/Th, Nb/La) together with Nd and Pb isotopes indicate involvement of an NMORB to EMORB 'transitional' mantle component mixed with variable amounts of a continental component. The magmas were derived from a source that developed high (U,Th)/Pb, U/Th and Sm/Nd over time. The geochemistry of Timan-Kanin basalts supports the hypothesis that the genesis of Devonian basaltic magmatism in the region resulted from local melting of transitional mantle and lower crust during rifting of a mainly non-volcanic continental rifted margin.

Hydrogeology and simulation of ground-water flow in the Silurian-Devonian aquifer system, Johnson County, Iowa

Science.gov (United States)

Tucci, Patrick; McKay, Robert M.

2006-01-01

Bedrock of Silurian and Devonian age (termed the “Silurian-Devonian aquifer system”) is the primary source of ground water for Johnson County in east-central Iowa. Population growth within municipal and suburban areas of the county has resulted in increased amounts of water withdrawn from this aquifer and water-level declines in some areas. A 3-year study of the hydrogeology of the Silurian-Devonian aquifer system in Johnson County was undertaken to provide a quantitative assessment of ground water resources and to construct a ground-water flow model that can be used by local governmental agencies as a management tool.

Process for oil shale retorting

Science.gov (United States)

Jones, John B.; Kunchal, S. Kumar

1981-10-27

Particulate oil shale is subjected to a pyrolysis with a hot, non-oxygenous gas in a pyrolysis vessel, with the products of the pyrolysis of the shale contained kerogen being withdrawn as an entrained mist of shale oil droplets in a gas for a separation of the liquid from the gas. Hot retorted shale withdrawn from the pyrolysis vessel is treated in a separate container with an oxygenous gas so as to provide combustion of residual carbon retained on the shale, producing a high temperature gas for the production of some steam and for heating the non-oxygenous gas used in the oil shale retorting process in the first vessel. The net energy recovery includes essentially complete recovery of the organic hydrocarbon material in the oil shale as a liquid shale oil, a high BTU gas, and high temperature steam.

China organic-rich shale geologic features and special shale gas production issues

Directory of Open Access Journals (Sweden)

Yiwen Ju

2014-06-01

Full Text Available The depositional environment of organic-rich shale and the related tectonic evolution in China are rather different from those in North America. In China, organic-rich shale is not only deposited in marine environment, but also in non-marine environment: marine-continental transitional environment and lacustrine environment. Through analyzing large amount of outcrops and well cores, the geologic features of organic-rich shale, including mineral composition, organic matter richness and type, and lithology stratigraphy, were analyzed, indicating very special characteristics. Meanwhile, the more complex and active tectonic movements in China lead to strong deformation and erosion of organic-rich shale, well-development of fractures and faults, and higher thermal maturity and serious heterogeneity. Co-existence of shale gas, tight sand gas, and coal bed methane (CBM proposes a new topic: whether it is possible to co-produce these gases to reduce cost. Based on the geologic features, the primary production issues of shale gas in China were discussed with suggestions.

Process of recovering shale oil

Energy Technology Data Exchange (ETDEWEB)

1949-01-17

A process is disclosed for recovering oil from shale rock by means of channels cut in the shale deposit, to which heat is carried for warming the shale mass and which are separated from the fume channels formed in the shale by parts of the shale rock, characterized in that heating elements are put down in the heating channels, which occupy less cross section than these channels, and in the so-formed space between the channel wall and the heating element a filling is placed, which facilitates heat transfer between the heating element and the shale and simultaneously prevents a streaming of the oily product gasified out of the shale from working into the heating element and stopping it.

Cyclostratigraphic calibration of the Famennian stage (Late Devonian, Illinois Basin, USA)

Science.gov (United States)

Pas, Damien; Hinnov, Linda; Day, James E. (Jed); Kodama, Kenneth; Sinnesael, Matthias; Liu, Wei

2018-04-01

The Late Devonian biosphere was affected by two of the most severe biodiversity crises in Earth's history, the Kellwasser and Hangenberg events near the Frasnian-Famennian (F-F) and the Devonian-Carboniferous (D-C) boundaries, respectively. Current hypotheses for the causes of the Late Devonian extinctions are focused on climate changes and associated ocean anoxia. Testing these hypotheses has been impeded by a lack of sufficient temporal resolution in paleobiological, tectonic and climate proxy records. While there have been recent advances in astronomical calibration that have improved the accuracy of the Frasnian time scale and part of the Famennian, the time duration of the entire Famennian Stage remains poorly constrained. During the Late Devonian, a complete Late Frasnian-Early Carboniferous succession of deep-shelf deposits accumulated in the epieric sea in Illinois Basin of the central North-American mid-continent. A record of this sequence is captured in three overlapping cores (H-30, Sullivan and H-32). The H-30 core section spans the F-F boundary; the Sullivan section spans almost all of the Famennian and the H-32 section sampled spans the interval of the Upper Famennian and the D-C boundary. To have the best chance of capturing Milankovitch cycles, 2000 rock samples were collected at minimum 5-cm-interval across the entire sequence. Magnetic susceptibility (MS) was measured on each sample and the preservation of climatic information into the MS signal was verified through geochemical analyses and low-temperature magnetic susceptibility acquisition. To estimate the duration of the Famennian Stage, we applied multiple spectral techniques and tuned the MS signal using the highly stable 405 kyr cycle for Sullivan and the obliquity cycle for the H-30 and H-32 cores. Based on the correlation between the cores we constructed a Famennian floating astronomical time scale, which indicates a duration of 13.5 ± 0.5 myr. An uncertainty of 0.5 myr was estimated for

Geochemistry of formation waters from the Wolfcamp and “Cline” shales: Insights into brine origin, reservoir connectivity, and fluid flow in the Permian Basin, USA

Science.gov (United States)

Engle, Mark A.; Reyes, Francisco R.; Varonka, Matthew S.; Orem, William H.; Lin, Ma; Ianno, Adam J.; Westphal, Tiffani M.; Xu, Pei; Carroll, Kenneth C.

2016-01-01

Despite being one of the most important oil producing provinces in the United States, information on basinal hydrogeology and fluid flow in the Permian Basin of Texas and New Mexico is lacking. The source and geochemistry of brines from the basin were investigated (Ordovician- to Guadalupian-age reservoirs) by combining previously published data from conventional reservoirs with geochemical results for 39 new produced water samples, with a focus on those from shales. Salinity of the Ca–Cl-type brines in the basin generally increases with depth reaching a maximum in Devonian (median = 154 g/L) reservoirs, followed by decreases in salinity in the Silurian (median = 77 g/L) and Ordovician (median = 70 g/L) reservoirs. Isotopic data for B, O, H, and Sr and ion chemistry indicate three major types of water. Lower salinity fluids (100 g/L), isotopically heavy (O and H) water in Leonardian [Permian] to Pennsylvanian reservoirs (2–3.2 km depth) is evaporated, Late Permian seawater. Water from the Permian Wolfcamp and Pennsylvanian “Cline” shales, which are isotopically similar but lower in salinity and enriched in alkalis, appear to have developed their composition due to post-illitization diffusion into the shales. Samples from the “Cline” shale are further enriched with NH4, Br, I and isotopically light B, sourced from the breakdown of marine kerogen in the unit. Lower salinity waters (3 km depth), which plot near the modern local meteoric water line, are distinct from the water in overlying reservoirs. We propose that these deep meteoric waters are part of a newly identified hydrogeologic unit: the Deep Basin Meteoric Aquifer System. Chemical, isotopic, and pressure data suggest that despite over-pressuring in the Wolfcamp shale, there is little potential for vertical fluid migration to the surface environment via natural conduits.

Paleozoic stratigraphy of two areas in southwestern Indiana

International Nuclear Information System (INIS)

Droste, J.B.

1976-09-01

Two areas recommended for evaluation as solid waste disposal sites lie along the strike of Paleozoic rocks in southwestern Indiana. Thin Pennsylvanian rocks and rocks of the upper Mississippian are at the bedrock surface in maturely dissected uplands in both areas. The gross subsurface stratigraphy beneath both areas is the same, but facies and thickness variation in some of the subsurface Paleozoic units provide for some minor differences between the areas. Thick middle Mississippi carbonates grade downward into clastics of lower Mississippian (Borden Group) and upper Devonian (New Albany Shale) rocks. Middle Devonian and Silurian rocks are dominated by carbonate lithologies. Upper Ordovician (Maquoketa Group) overly carbonates of middle Ordovician age. Thick siltstone and shale of the Borden Group-New Albany Shale zone and Maquoketa Group rocks should be suitable for repository development

Empirical Methods for Detecting Regional Trends and Other Spatial Expressions in Antrim Shale Gas Productivity, with Implications for Improving Resource Projections Using Local Nonparametric Estimation Techniques

Science.gov (United States)

Coburn, T.C.; Freeman, P.A.; Attanasi, E.D.

2012-01-01

The primary objectives of this research were to (1) investigate empirical methods for establishing regional trends in unconventional gas resources as exhibited by historical production data and (2) determine whether or not incorporating additional knowledge of a regional trend in a suite of previously established local nonparametric resource prediction algorithms influences assessment results. Three different trend detection methods were applied to publicly available production data (well EUR aggregated to 80-acre cells) from the Devonian Antrim Shale gas play in the Michigan Basin. This effort led to the identification of a southeast-northwest trend in cell EUR values across the play that, in a very general sense, conforms to the primary fracture and structural orientations of the province. However, including this trend in the resource prediction algorithms did not lead to improved results. Further analysis indicated the existence of clustering among cell EUR values that likely dampens the contribution of the regional trend. The reason for the clustering, a somewhat unexpected result, is not completely understood, although the geological literature provides some possible explanations. With appropriate data, a better understanding of this clustering phenomenon may lead to important information about the factors and their interactions that control Antrim Shale gas production, which may, in turn, help establish a more general protocol for better estimating resources in this and other shale gas plays. ?? 2011 International Association for Mathematical Geology (outside the USA).

Oil shale, shale oil, shale gas and non-conventional hydrocarbons

Directory of Open Access Journals (Sweden)

Clerici A.

2015-01-01

Full Text Available In recent years there has been a world “revolution” in the field of unconventional hydrocarbon reserves, which goes by the name of “shale gas”, gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also “oil shales” (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil, extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

The first direct evidence of a Late Devonian coelacanth fish feeding on conodont animals

OpenAIRE

Zaton, M.; Broda, K.; Qvarnström, M.; Niedzwiedzki, G.; Ahlberg, P.E.

2017-01-01

We describe the first known occurrence of a Devonian coelacanth specimen from the lower Famennian of the Holy Cross Mountains, Poland, with a conodont element preserved in its digestive tract. A small spiral and phosphatic coprolite (fossil excrement) containing numerous conodont elements and other unrecognized remains was also found in the same deposits. The coprolite is tentatively attributed to the coelacanth. Although it is unclear whether the Late Devonian coelacanth from Poland was an a...

Impact of Oxidative Dissolution on Black Shale Fracturing: Implication for Shale Fracturing Treatment Design

Science.gov (United States)

You, L.; Chen, Q.; Kang, Y.; Cheng, Q.; Sheng, J.

2017-12-01

Black shales contain a large amount of environment-sensitive compositions, e.g., clay minerals, carbonate, siderite, pyrite, and organic matter. There have been numerous studies on the black shales compositional and pore structure changes caused by oxic environments. However, most of the studies did not focus on their ability to facilitate shale fracturing. To test the redox-sensitive aspects of shale fracturing and its potentially favorable effects on hydraulic fracturing in shale gas reservoirs, the induced microfractures of Longmaxi black shales exposed to deionized water, hydrochloric acid, and hydrogen peroxide at room-temperature for 240 hours were imaged by scanning electron microscopy (SEM) and CT-scanning in this paper. Mineral composition, acoustic emission, swelling, and zeta potential of the untreated and oxidative treatment shale samples were also recorded to decipher the coupled physical and chemical effects of oxidizing environments on shale fracturing processes. Results show that pervasive microfractures (Fig.1) with apertures ranging from tens of nanometers to tens of microns formed in response to oxidative dissolution by hydrogen peroxide, whereas no new microfracture was observed after the exposure to deionized water and hydrochloric acid. The trajectory of these oxidation-induced microfractures was controlled by the distribution of phyllosilicate framework and flaky or stringy organic matter in shale. The experiments reported in this paper indicate that black shales present the least resistance to crack initiation and subcritical slow propagation in hydrogen peroxide, a process we refer to as oxidation-sensitive fracturing, which are closely related to the expansive stress of clay minerals, dissolution of redox-sensitive compositions, destruction of phyllosilicate framework, and the much lower zeta potential of hydrogen peroxide solution-shale system. It could mean that the injection of fracturing water with strong oxidizing aqueous solution may

Evaluating possible industrial applications of combustible shales and shale ash wastes

Directory of Open Access Journals (Sweden)

Н. К. Кондрашева

2016-08-01

Full Text Available Today energy consumption is constantly growing while explored reserves of easily accessible oil are depleting, which is a reason why most countries tend to diversify their energy mix, develop non-hydrocarbon energy sources and use domestic types of fuel, including the low grade ones. Thereby interest is raised to such a source of hydrocarbons as combustible shales. Combustible shales appear to be one of the highest-potential types of organic raw materials, which may offset and in future even substitute oil products and gas. The paper is investigating behavior and structure of combustible shales during heat treatment in order to identify their possible industrial applications. A synchronous thermal analysis has been held, chemical composition of combustible shales’ mineral fraction and optimal conditions for shale fines briquetting have been determined.

Trace metal distribution and mobility in drill cuttings and produced waters from Marcellus Shale gas extraction: Uranium, arsenic, barium

International Nuclear Information System (INIS)

Phan, Thai T.; Capo, Rosemary C.; Stewart, Brian W.; Graney, Joseph R.; Johnson, Jason D.; Sharma, Shikha; Toro, Jaime

2015-01-01

Highlights: • Distributions of U, As, and Ba in Marcellus Shale were determined. • As is primarily associated with sulfide minerals, Ba with exchange sites. • Most U is in the silicate minerals, but up to 20% is partitioned into carbonate. • Low [U] and [As] in produced water are consistent with reducing downhole conditions. • Proper waste management should account for potential mobilization of U and As. - Abstract: Development of unconventional shale gas wells can generate significant quantities of drilling waste, including trace metal-rich black shale from the lateral portion of the drillhole. We carried out sequential extractions on 15 samples of dry-drilled cuttings and core material from the gas-producing Middle Devonian Marcellus Shale and surrounding units to identify the host phases and evaluate the mobility of selected trace elements during cuttings disposal. Maximum whole rock concentrations of uranium (U), arsenic (As), and barium (Ba) were 47, 90, and 3333 mg kg −1 , respectively. Sequential chemical extractions suggest that although silicate minerals are the primary host for U, as much as 20% can be present in carbonate minerals. Up to 74% of the Ba in shale was extracted from exchangeable sites in the shale, while As is primarily associated with organic matter and sulfide minerals that could be mobilized by oxidation. For comparison, U and As concentrations were also measured in 43 produced water samples returned from Marcellus Shale gas wells. Low U concentrations in produced water (<0.084–3.26 μg L −1 ) are consistent with low-oxygen conditions in the wellbore, in which U would be in its reduced, immobile form. Arsenic was below detection in all produced water samples, which is also consistent with reducing conditions in the wellbore minimizing oxidation of As-bearing sulfide minerals. Geochemical modeling to determine mobility under surface storage and disposal conditions indicates that oxidation and/or dissolution of U

The Role of Terrestrial N along a Frasnian/Famennian Boundary Transect of the Appalachian Basin

Science.gov (United States)

Tuite, Michael; Macko, Stephen

2010-05-01

A causal link between the Late Devonian emergence of forest ecosystems and episodic black shale deposition has been proposed by several authors. Most attribute increases in epicontinental basin productivity to elevated rates of terrestrial phosphorus weathering facilitated by the co-evolution of root systems and soils. Two reasons to suspect that an increase in the P weathering flux was not the primary cause of organic-rich shale deposition are as follows. First, most Late Devonian black shales were deposited during sea level transgressions, periods when riverine fluxes of sediment and mineral nutrients such as P to marine basins were diminished. Second, Late Devonian forests were restricted to warm, moist lowlands where P was sequestered in soils as inorganic, occluded forms. However, the export flux of reactive N from these forests to adjacent epeiric seas by riverine and atmospheric deposition was enhanced by the warm, wet climate and expanding areal extent of forests. Abundant terrestrial reactive N primed the marine eutrophication pump by extending the residence time of P in the photic zone, permitting extensive growth of primary biomass. The consequent flux of organic matter to the sea floor created anoxic bottom waters that, in turn, allowed for the remobilization of P into the water column. Based on abundance and isotopic analyses of organic and inorganic C, N, P, and S from terrestrial and marine environments within and adjacent to the Late Devonian Appalachian Basin, this latter scenario is supported.

Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

Distillation of bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Seguin, M

1875-02-16

The retort with its accessories constitutes a distillation apparatus for shale composed of a cylindrical, vertical, fixed, tubular, and of ring form metal retort. Also it is comprised of a special hearth of large dimensions in the form of a circular pocket receiving from the retort as heating agent the distilled shale and emitting by radiation the heat that makes the distillation apparatus for the shale act.

Soil development on loess overlying Cretaceous sediments and Devonian limestones

Czech Academy of Sciences Publication Activity Database

Žigová, Anna; Šťastný, Martin

2015-01-01

Roč. 12, č. 3 (2015), s. 267-278 ISSN 1214-9705 Institutional support: RVO:67985831 Keywords : loess * Cretaceous and Devonian rocks * mineral composition * soil development * Luvic Chernozem * Albic Luvisol Subject RIV: DF - Soil Science Impact factor: 0.561, year: 2015

Devonian and Lower Carboniferous conodont biostratigraphy, Spanish Central Pyrenees

NARCIS (Netherlands)

Boersma, Kerst Th.

1973-01-01

Conodont faunas were collected from the Devonian and Lower Carboniferous in an area ranging from the Rio Fsera (prov. of Huesca) in the west to the Rio Llobregat (prov. of Barcelona) in the east. Most conodont zones and -Faunas recognized in Germany and Spain could be distinguished. The ages of the

Organic substances of bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Lanin, V A; Pronina, M V

1944-01-01

Samples of Gdov (Estonia) and Volga (Russia) oil shales were oxidized by alkaline permanganate to study the distribution of carbon and the composition of the resulting oxidation products. Gdov shale was rather stable to oxidation and, after 42 hours 61.2 percent of the organic material remained unoxidized. Five hundred hours were required for complete oxidation, and the oxidation products consisted of CO/sub 2/, acetic, oxalic, and succinic acids. The oxidation products from Volga shale consisted of CO/sub 2/, acetic, oxalic, succinic, adipic, phthalic, benzenetricarboxylic, benzenetetracarboxylic, and benzenepentacarboxylic acids. The results indicated that Gdov shale is free of humic substances and is of sapropelic origin, while Volga shale is of sapropelic-humic origin.

Conversion characteristics of 10 selected oil shales

Energy Technology Data Exchange (ETDEWEB)

Miknis, F.P.

1989-08-01

The conversion behavior of 10 oil shale from seven foreign and three domestic deposits has been studied by combining solid- and liquid-state nuclear magnetic resonance (NMR) measurements with material balance Fischer assay conversion data. The extent of aromatization of aliphatic carbons was determined. Between zero and 42% of the raw shale aliphatic carbon formed aromatic carbon during Fischer assay. For three of the shales, there was more aromatic carbon in the residue after Fisher assay than in the raw shale. Between 10 and 20% of the raw shale aliphatic carbons ended up as aliphatic carbons on the spent shale. Good correlations were found between the raw shale aliphatic carbon and carbon in the oil and between the raw shale aromatic carbon and aromatic carbon on the spent shale. Simulated distillations and molecular weight determinations were performed on the shale oils. Greater than 50% of the oil consisted of the atmospheric and vacuum gas oil boiling fractions. 14 refs., 15 figs., 1 tab.

Shale gas exploitation: Status, problems and prospect

Directory of Open Access Journals (Sweden)

Shiqian Wang

2018-02-01

Full Text Available Over the past five years, great progress has been made in shale gas exploitation, which has become the most driving force for global gas output growth. Hydrocarbon extraction from shale helps drive the USA on the road to energy independence. Besides, shale oil & gas production has been kept in a sustained growth by continuous improvement in drilling efficiency and well productivity in the case of tumbling oil prices and rig counts. Shale gas reserves and production have been in a rapid growth in China owing to the Lower Paleozoic Wufeng and Longmaxi shale gas exploitation in the Sichuan Basin, which has become an important sector for the future increment of gas reserves and output in China. However, substantial progress has been made neither in non-marine shale gas exploitation as previously expected nor in the broad complicated tectonic areas in South China for which a considerable investment was made. Analysis of the basic situation and issues in domestic shale gas development shows that shale gas exploitation prospects are constrained by many problems in terms of resources endowment, horizontal well fracturing technology, etc. especially in non-marine shale deposits and complicated tectonic areas in South China where hot shales are widely distributed but geological structures are found severely deformed and over matured. Discussion on the prospects shows that the sustained and steady growth in shale gas reserves and production capacity in the coming years lies in the discovery and supersession of new shale plays in addition to Wufeng and Longmaxi shale plays, and that a technological breakthrough in ultra-high-pressure and ultra-deep (over 3500 m buried in the Sichuan Basin marine shale gas exploitation is the key and hope. Keywords: Shale gas, Exploitation, Marine facies, Hot shale, Resource endowment, Sichuan Basin, South China, Complicated tectonic area, Gas play

End-Devonian extinction and a bottleneck in the early evolution of modern jawed vertebrates.

Science.gov (United States)

Sallan, Lauren Cole; Coates, Michael I

2010-06-01

The Devonian marks a critical stage in the early evolution of vertebrates: It opens with an unprecedented diversity of fishes and closes with the earliest evidence of limbed tetrapods. However, the latter part of the Devonian has also been characterized as a period of global biotic crisis marked by two large extinction pulses: a "Big Five" mass extinction event at the Frasnian-Famennian stage boundary (374 Ma) and the less well-documented Hangenberg event some 15 million years later at the Devonian-Carboniferous boundary (359 Ma). Here, we report the results of a wide-ranging analysis of the impact of these events on early vertebrate evolution, which was obtained from a database of vertebrate occurrences sampling over 1,250 taxa from 66 localities spanning Givetian to Serpukhovian stages (391 to 318 Ma). We show that major vertebrate clades suffered acute and systematic effects centered on the Hangenberg extinction involving long-term losses of over 50% of diversity and the restructuring of vertebrate ecosystems worldwide. Marine and nonmarine faunas were equally affected, precluding the existence of environmental refugia. The subsequent recovery of previously diverse groups (including placoderms, sarcopterygian fish, and acanthodians) was minimal. Tetrapods, actinopterygians, and chondrichthyans, all scarce within the Devonian, undergo large diversification events in the aftermath of the extinction, dominating all subsequent faunas. The Hangenberg event represents a previously unrecognized bottleneck in the evolutionary history of vertebrates as a whole and a historical contingency that shaped the roots of modern biodiversity.

Apparatus for treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

1942-11-24

A method is given of transforming finely crushed bituminous shale, for instance of maximum particle size of about 5 mm, into balls, nodules, or similar shapes, in which the shale to be treated is passed in the form of lumps through a rotary drum. The finely crushed shale with a higher content of moisture is brought into contact with finely crushed shale of a lower content of moisture, and thereby serves as kernel material during the formation of the nodules or similar shapes.

Stratigraphy and petroleum possibilities of lower Upper Devonian (Frasnian and lower Framennian) strata, Southwestern Utah

Science.gov (United States)

Biller, Edward J.

1976-01-01

The lower Upper Devonian rocks in southwestern Utah--the Guilmette Formation and equivalents--represent a final regressive pulse of the major Late Devonian marine inundation of the Western Interior of the United States and record marine carbonate deposition on a wide continental shelf. They consist primarily of limestone, dolomite, and quartz arenite deposited in a shallow north-trending miogeosyncline, which constituted a single major basin of accumulation on this shelf. The Guilmette Formation and equivalents were deposited in shallow normal to hypersaline marine waters. The environments of deposition include: a moderate- to high-energy intertidal environment, a moderate-energy subtidal environment, a lower energy, deeper subtidal environment below effective wave base, and a high-energy environment in local shallow areas of mud mounds and bioherms. The carbonate deposition of the Guilmette Formation and equivalents was interrupted periodically by the deposition of quartz arenites. These may represent the breaking up of the miogeosynclinal-cratonic pattern of deposition. In most areas, the Guilmette and equivalents are overlain by a thin transgressive marine quartz arenite deposit--the Cove Fort Quartzite and basal Leatham equivalent. Previous paleontologic evidence indicated a general Middle to Late Devonian age for the Guilmette Formation. The present study narrows this range and suggests that the age of the Guilmette Formation and its equivalents is late Middle Devonian (Stringocephalus brachiopod zone) to early Late Devonian (Uppermost Palmatolepis gigas conodont zone). Available subsurface data suggest that the petroleum possibilities of the Guilmette Formation and equivalents in southwestern Utah are poor. Several tests have penetrated .the interval with only minor shows of oil in rocks with low porosity and permeability. Nevertheless, many outcrop samples of the same interval, appear to have excellent porosity and permeability and a strongly fetid odor,

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1922-07-21

In the distillation of shale and similar materials the shale is ground and briquetted and the briquettes are placed in a retort so that air passages are left between them, after which they are uniformly and slowly heated to at least 700/sup 0/C, the air passages facilitating the escape of the oil vapors, and the slow heating preventing fusion of the flux forming constituents. After the bitumen has been driven off, air is passed into the retort and heating continued to about 1050/sup 0/C, the result being a porous product suitable for insulating purposes or as a substitute for kieselguhr. The ground shale may be mixed prior to distillation with peat, sawdust, or the like, and with substances which yield acids, such as chlorides, more particularly magnesium chloride, the acids acting on the bitumen.

Distilling shale

Energy Technology Data Exchange (ETDEWEB)

Heyl, G E

1917-02-06

The yield of oil obtained by distilling shale is increased by first soaking the shale with about 10 percent of its volume of a liquid hydrocarbon for a period of 24 hours or longer. Distillation is carried on up to a temperature of about 220/sup 0/C., and a further 10 percent of hydrocarbon is then added and the distillation continued up to a temperature of about 400/sup 0/C.

The global stratotype section and point of the Silurian-Devonian boundary

Czech Academy of Sciences Publication Activity Database

Chlupáč, I.; Hladil, Jindřich

2000-01-01

Roč. 225, - (2000), s. 1-6+1 Pl. ISSN 0341-4116 Institutional research plan: CEZ:AV0Z3013912 Keywords : Silurian-Devonian * global stratotype section and point (GSSP) * stratigraphy Subject RIV: DB - Geology ; Mineralogy

Refining the Early Devonian time scale using Milankovitch cyclicity in Lochkovian–Pragian sediments (Prague Synform, Czech Republic)

Czech Academy of Sciences Publication Activity Database

da Silva, A.C.; Hladil, Jindřich; Chadimová, Leona; Slavík, Ladislav; Hilgen, F. J.; Bábek, O.; Dekkers, M. J.

2016-01-01

Roč. 455, 1 December (2016), s. 125-139 ISSN 0012-821X R&D Projects: GA ČR GA14-18183S Institutional support: RVO:67985831 Keywords : orbital time scale * spectral analysis * Devonian * magnetic susceptibility * gamma ray spectrometry * limestone * Early Devonian * Lochkovian * Pragian * Emsian * Barrandian * peri-Gondwanan basins Subject RIV: DB - Geology ; Mineralogy Impact factor: 4.409, year: 2016

Devonian (Emsian-Eifelian) fish from the Lower Bokkeveld Group (Ceres Subgroup), South Africa

Science.gov (United States)

Anderson, M. E.; Almond, J. E.; Evans, F. J.; Long, J. A.

1999-07-01

Four major groups of fish are represented by fragmentary remains from South Africa's Lower Bokkeveld Group of Early to Middle Devonian age: the Acanthodii, Chondrichthyes, Placodermi and Osteichthyes. These represent the oldest known occurrences of these groups in southern Africa, as well as an important addition to the very meagre record of earlier Devonian fish from the Malvinokaffric Province of southwestern Gondwana. Bokkeveld fish material comes from the Gydo (Late Emsian) and Tra Tra (Middle Eifelian) Formations of the Western Cape and Eastern Cape Provinces. The cosmopolitan marine acanthodian Machæracanthus is represented only by isolated fin spines which may belong to two different species on the basis of their external ornamentation, cross-sectional outline and internal histology. The elasmobranchs are represented by four elements: (1) a flattened chondrocranium which bears affinity to the Late Devonian-Carboniferous symmoriid (protacrodont) 'cladodont' sharks. It is probably the earliest known (Emsian) shark chondrocranium; (2) an isolated, primitive scapulocoracoid with a very short coracoidal ridge; (3) ankylosed and isolated radials, interpreted as parts of pterygial plates of a paired fin of an unknown chondrichthyan bearing affinity to the Middle Devonian Zamponiopteron from Bolivia; and (4) isolated barlike structures, perhaps gill arch or a jaw elements, thought to be from the same taxon as (3). The placoderms are represented by an incomplete trunk armour and fragmentary, finely ornamented plates of a primitive antiarch. The Osteichthyes are represented by a single large scale of an unidentified dipnoan from the Eifelian of the Cedarberg range, as well as a probable sarcopterygian dermal plate from the Emsian of the Prince Albert area. These are among the earliest sarcopterygian remains recorded from the Malvinokaffric Province.

Natural gas production verification tests

International Nuclear Information System (INIS)

1992-02-01

This Environmental Assessment (EA) has been prepared by the Department of Energy (DOE) in compliance with the requirements of the National Environmental Policy Act of 1969. The Department of Energy (DOE) proposes to fund, through a contract with Petroleum Consulting Services, Inc. of Canton, Ohio, the testing of the effectiveness of a non-water based hydraulic fracturing treatment to increase gas recovery from low-pressure, tight, fractured Devonian Shale formations. Although Devonian Shales are found in the Appalachian, Michigan, and Illinois Basins, testing will be done only in the dominant, historical five state area of established production. The objective of this proposed project is to assess the benefits of liquid carbon dioxide (CO 2 )/sand stimulations in the Devonian Shale. In addition, this project would evaluate the potential nondamaging (to the formation) properties of this unique fracturing treatment relative to the clogging or chocking of pores and fractures that act as gas flow paths to the wellbore in the target gas-producing zones of the formation. This liquid CO 2 /sand fracturing process is water-free and is expected to facilitate gas well cleanup, reduce the time required for post-stimulation cleanup, and result in improved production levels in a much shorter time than is currently experienced

Common clay and shale

Science.gov (United States)

Virta, R.L.

2000-01-01

Part of the 1999 Industrial Minerals Review. The clay and shale market in 1999 is reviewed. In the U.S., sales or use of clay and shale increased from 26.4 million st in 1998 to 27.3 million st in 1999, with an estimated 1999 value of production of $143 million. These materials were used to produce structural clay products, lightweight aggregates, cement, and ceramics and refractories. Production statistics for clays and shales and for their uses in 1999 are presented.

Relation of peat to oil shale

Energy Technology Data Exchange (ETDEWEB)

Linker, S

1924-01-01

Samples of oil shale from the Green River formation and from Elko (Nev.), Brazil, Austria, and South Africa were examined, and several varieties of shale were found. Green River oil shale represents three of the more common types plus one less common type. These were: contorted shale with a velvety appearance, thin paper shale resembling the curled-up leaves of a book, massive black shale resembling a piece of rubber, and a less common type, which showed the bedding planes very clearly. The Elko (Nev.) shale was a light buff color; the shale from Brazil resembled a piece of petrified peat. When the shales were cut very thin, their colors ranged from yellow to reddish-brown. The composition, as seen under the microscope, was of well-preserved plant material such as spores, pollen grains, fragments of cell tissues, algae, fungi, bacteria, macerated organic residue, small pieces of resin, animal fossils, and translucent bodies. Oil shale was produced from organic material that accumulated in peat bogs, marshes, or swamps in fresh or salt waters. The organic matter was decomposed by bacterial action. Certain parts of the plants decayed more readily than others. Before lithification occurred, a chemical action took place that changed the softer tissues of the plant debris into a gel. This collodial matter penetrated and surrounded the more resistant fragments and preserved them from further decay. Certain bog waters contain a high percentage of humic acids in solution or collodial suspension and produce insoluble humates when neutralized. These humates are probably the so-called kerogen bodies.

Re Os depositional ages and seawater Os estimates for the Frasnian Famennian boundary: Implications for weathering rates, land plant evolution, and extinction mechanisms

Science.gov (United States)

Turgeon, Steven C.; Creaser, Robert A.; Algeo, Thomas J.

2007-09-01

Four TOC-rich shale intervals spanning the Frasnian-Famennian (F-F) boundary were recovered in a drillcore (West Valley NX-1) from western New York (USA) and radiometrically dated using Re-Os. Two of the black shale intervals (WVC785 from ˜ 2.9 m below, and WVC754 from ˜ 6.4 m above the F-F boundary, respectively) yielded statistically overlapping ages with uncertainties of initial 187Os/ 188Os (0.45 to 0.47), reflecting contemporaneous seawater Os values, are low but similar to the value of 0.42 reported for the Exshaw Fm (Canada) at the Devonian-Mississippian boundary (ca. 361 Ma) [Selby D., Creaser R.A., 2005. Direct radiometric dating of the Devonian-Mississippian time-scale boundary using the Re-Os black shale geochronometer. Geology 33, 545-548]. This may suggest fairly constant and low global continental weathering rates during the Late Devonian, although in view of the short residence time of Os in seawater (˜ 1-4 × 10 4 yr), further measurements are needed to assess potential short-term variation in seawater Os ratios. Owing to low Os and Re abundances at the F-F boundary, our data are inconsistent with long-term volcanism and bolide impact as potential Late Devonian mass extinction mechanisms. In addition, the Frasnian-Famennian ocean appears to have been depleted with respect to Re, possibly indicating an exhaustion of the Re seawater reservoir owing to high burial rates of redox-sensitive elements under dysoxic/anoxic conditions leading up to the F-F boundary.

Carbon sequestration in depleted oil shale deposits

Science.gov (United States)

Burnham, Alan K; Carroll, Susan A

2014-12-02

A method and apparatus are described for sequestering carbon dioxide underground by mineralizing the carbon dioxide with coinjected fluids and minerals remaining from the extraction shale oil. In one embodiment, the oil shale of an illite-rich oil shale is heated to pyrolyze the shale underground, and carbon dioxide is provided to the remaining depleted oil shale while at an elevated temperature. Conditions are sufficient to mineralize the carbon dioxide.

Origin of uranium and other metal concentrations in the Helmsdate granite and the Devonian sediments of the north-east of Scotland

Energy Technology Data Exchange (ETDEWEB)

Tweedie, J R

1981-01-01

An examination of the radiometrically anomalous Caledonian Helmsdale granite and certain radiometric localities in the Devonian sediments of Caithness has been undertaken in order to discover the processes of U concentration in the different rock types. The study is based mainly on geochemical examination, with analyses for U, Th, Cu, Zn, Pb, Mo, Zr, Rb, Sr, Bi, Se, P/sub 2/O/sub 5/, and K/sub 2/O being carried out. The granite was found to have a high mean U content (9 ppm), approximately twice that expected from comparison with the world granite average (4 ppm), whilst zones of intense alteration gave U enrichments of up to 71 ppm. These latter have a mineralogy and geochemistry distinct from the normal granite. A limited Cu-Mo stockwork mineralisation was discovered almost coincident with a highly radioactive hydrocarbon vein. The main U concentrations in the Caithness sediments occur in thin phosphatic horizons. In these, U ranges from 100 to 1000 ppm and is paralleled by the phosphate in an approximately linear relationship of 100 ppm U/1% P/sub 2/O/sub 5/. Black shales contain low level U concentrations with anomalously high Zn and/or Mo. (author).

Hydrogenation of Estonian oil shale and shale oil

Energy Technology Data Exchange (ETDEWEB)

Kogerman, P N; Kopwillem, J

1932-01-01

Kukersite was heated in an atmosphere of hydrogen, nitrogen, or water in three series of experiments. Shale samples were heated at 370/sup 0/ to 410/sup 0/C for 2 to 3/sup 1///sub 2/ hours in the presence of 106 to 287 kg/sq cm pressure of water, nitrogen, or hydrogen. In some experiments 5 percent of iron oxide was added to the shale. The amount of kerogen liquefied by hydrogenation was not greater than the amount of liquid products obtained by ordinary distillation. On hydrogenation, kukersite absorbed 1.8 weight-percent of hydrogen. Almost no hydrogenation took place below the decomposition point of kerogen, and the lighter decomposition products were mainly hydrogenated. Hydrogenation of the shale prevented coke formation. Heating kukersite or its crude oil at temperatures of 400/sup 0/ to 410/sup 0/C under 250 kg/sq cm hydrogen pressure produced paraffinic and naphthenic oils of lower boiling points. At higher temperatures and after long-continued heating, the formation of aromatic hydrocarbons was observed.

Leakage detection of Marcellus Shale natural gas at an Upper Devonian gas monitoring well: a 3-d numerical modeling approach.

Science.gov (United States)

Zhang, Liwei; Anderson, Nicole; Dilmore, Robert; Soeder, Daniel J; Bromhal, Grant

2014-09-16

Potential natural gas leakage into shallow, overlying formations and aquifers from Marcellus Shale gas drilling operations is a public concern. However, before natural gas could reach underground sources of drinking water (USDW), it must pass through several geologic formations. Tracer and pressure monitoring in formations overlying the Marcellus could help detect natural gas leakage at hydraulic fracturing sites before it reaches USDW. In this study, a numerical simulation code (TOUGH 2) was used to investigate the potential for detecting leaking natural gas in such an overlying geologic formation. The modeled zone was based on a gas field in Greene County, Pennsylvania, undergoing production activities. The model assumed, hypothetically, that methane (CH4), the primary component of natural gas, with some tracer, was leaking around an existing well between the Marcellus Shale and the shallower and lower-pressure Bradford Formation. The leaky well was located 170 m away from a monitoring well, in the Bradford Formation. A simulation study was performed to determine how quickly the tracer monitoring could detect a leak of a known size. Using some typical parameters for the Bradford Formation, model results showed that a detectable tracer volume fraction of 2.0 × 10(-15) would be noted at the monitoring well in 9.8 years. The most rapid detection of tracer for the leak rates simulated was 81 days, but this scenario required that the leakage release point was at the same depth as the perforation zone of the monitoring well and the zones above and below the perforation zone had low permeability, which created a preferred tracer migration pathway along the perforation zone. Sensitivity analysis indicated that the time needed to detect CH4 leakage at the monitoring well was very sensitive to changes in the thickness of the high-permeability zone, CH4 leaking rate, and production rate of the monitoring well.

Shale gas - Risks and stakes

International Nuclear Information System (INIS)

Parks, Olivier

2014-01-01

This book aims at exploring all aspects of the shale gas issue: geological data, environmental impacts, financial aspects and economical impacts of shale gas exploitation. It compares the available information with the field reality and defeats the dogmatic mirages. The research and compilation work carried out by the author make this book a reference in the domain of shale gas exploitation

Process of briquetting fine shale

Energy Technology Data Exchange (ETDEWEB)

Kraemer, J

1943-05-05

A process is described for the preparation of briquetts of fine bituminous shale, so-called Mansfield copper shale, without addition of binding material, characterized in that the fine shale is warmed to about 100/sup 0/C and concurrently briquetted in a high-pressure rolling press or piece press under a pressure of 300 to 800 kg/cm/sup 2/.

Neutron activation determination of rhenium in shales shales and molybdenites

International Nuclear Information System (INIS)

Zajtsev, E.I.; Radinovich, B.S.

1977-01-01

Described is the technique for neutron activation determination of rhenium in shales and molybdenites with its radiochemical extraction separation by methyl-ethyl ketone. The sensitivity of the analysis is 5x10 -7 %. Experimental checking of the developed technique in reference to the analysis of shales and molybdenites was carried out. Estimated is the possibility of application of X-ray gamma-spectrometer to instrumental determination of rhenium in molybdenites

Preparation of hydraulic cement from oil-shale

Energy Technology Data Exchange (ETDEWEB)

1921-08-28

A process for the preparation of hydraulic cement from oil-shale or oil-shale residue is characterized in that, the oil-shale or shale-coke together with a slight amount of marl is burned under sintering conditions and the residue obtained is ground to a fine dust.

Laboratory characterization of shale pores

Science.gov (United States)

Nur Listiyowati, Lina

2018-02-01

To estimate the potential of shale gas reservoir, one needs to understand the characteristics of pore structures. Characterization of shale gas reservoir microstructure is still a challenge due to ultra-fine grained micro-fabric and micro level heterogeneity of these sedimentary rocks. The sample used in the analysis is a small portion of any reservoir. Thus, each measurement technique has a different result. It raises the question which methods are suitable for characterizing pore shale. The goal of this paper is to summarize some of the microstructure analysis tools of shale rock to get near-real results. The two analyzing pore structure methods are indirect measurement (MIP, He, NMR, LTNA) and direct observation (SEM, TEM, Xray CT). Shale rocks have a high heterogeneity; thus, it needs multiscale quantification techniques to understand their pore structures. To describe the complex pore system of shale, several measurement techniques are needed to characterize the surface area and pore size distribution (LTNA, MIP), shapes, size and distribution of pore (FIB-SEM, TEM, Xray CT), and total porosity (He pycnometer, NMR). The choice of techniques and methods should take into account the purpose of the analysis and also the time and budget.

Facies-succession and architecture of the third-order sequences and their stratigraphic framework of the Devonian in Yunnan-Guizhou-Guangxi area, South China

Directory of Open Access Journals (Sweden)

Mei Mingxiang

2013-01-01

Full Text Available The Caledonian orogeny at the end of the Silurian resulted in great changes in the palaeogeography in the Yunnan-Guizhou-Guangxi area of South China; the continental area of the Early Paleozoic evolved into the extensive Dian-Qian-Gui Sea in the Late Paleozoic. Early in the Devonian, as a result of a major transgression, seawater encroached gradually from the south to the north and clastic facies were deposited. Carbonate deposition was then established in the Yunnan-Guizhou-Guangxi area, with a palaeogeography marked by attached platforms, isolated platforms and narrow basins. As a result of the Ziyun movement towards the end of the Devonian, the Upper Devonian strata are regressive and thin out from the open-sea to the land areas. A study of the nature and distribution of sedimentary facies in space and time recognises 13 third-order sequences in the Devonian strata in Yunnan-Guizhou-Guangxi area, and these form two second-order sequences. The strata of the Lower Devonian comprise 5 third-order sequences (SQ1 to SQ5, which are dominated by transgressive clastics. 4 third-order sequences (SQ6 to SQ9 in the Middle Devonian are characterized by alternations of transgressive clastics and highstand carbonates. In the Upper Devonian, carbonates constitute 4 third-order sequences (SQ10 to SQ13, which are generally marked by the transgressive limestones and highstand dolomites. On the basis of earlier biostratigraphic studies, sea-level changes represented by the third-order sequences with their different facies successions are explored, and the sequence stratigraphic framework is established. Therefore, the Devonian strata in the study area provide an example for further understanding of depositional trends within the sequence-stratigraphic framework.

Oil shale highlights

International Nuclear Information System (INIS)

1994-01-01

The low prices of crude oil have continued to retard the commercial development of oil shale and other syn fuels. Although research funds are more difficult to find, some R and D work by industry, academia, and governmental agencies continues in the United States and in other parts of the world. Improvements in retorting technology, upgrading oil-shale feedstock, and developing high-value niche-market products from shale oil are three notable areas of research that have been prominent for the past several years. Although the future prices of conventional crude cannot be predicted, it seems evident that diminishing supplies and a burgeoning world population will force us to turn to alternate fossil fuels as well as to cleaner sources of non-fossil energy. (author)

Improvements in the distillation of shale, etc

Energy Technology Data Exchange (ETDEWEB)

Noad, J

1912-09-20

A process for treating shale and other bituminous substances containing sulfur and obtaining desulfurized products of distillation consisting in the consecutive steps of crushing the shale, mixing a suitable liquid with the shale granules, mixing slaked lime with the liquid coated shale granules, and gradually feeding the lime coated shale granules into a retort presenting a series of ledges or the like and working the shale granules down from ledge to ledge so that they are continuously agitated while being heated, the volatile constituents escaping through the lime coating and being conducted away from the upper part of the retort to suitable condensing apparatus, and the sulfur being arrested by the lime coating and together with the exhausted shale and other impurities being discharged from the lower part of the retort.

Vascular plants from the Devonian to Lower Cretaceous in southern Africa

Directory of Open Access Journals (Sweden)

J. M. Anderson

1983-11-01

Full Text Available The succession of pre-angiospermous megafloras in southern Africa from the Devonian to Lower Cretaceous is outlined. Interrelationships between continental drift, global climatic trends, and floral and faunal evolution are emphasized. Data are given on numbers of assemblages sampled; on species diversity; and on relative abundance of each genus per productive ‘formation’. A total of 79 genera and about 250 species are recognized in the 150 assemblages from the 11 horizons considered. Floras are unknown from the Carboniferous and are as yet undescribed from the Jurassic. Aside from these gaps, a good idea of the floral development is obtained. Diversity lows of around 5 to 10 species per ‘formation’ are witnessed in the Devonian, whereas a peak of 112 species is encountered in the Upper Triassic Molteno Formation. Diversity remains around 20 to 30 species for all other ‘formations’.

Geochemical characterization and miospore biochronostratigraphy of the Frasnian anoxic event in the Parnaiba basin, Northeast Brazil

International Nuclear Information System (INIS)

Rodrigues, R.; De Melo, J.H.G.; Alves, D.B.; Loboziak, S.

1995-01-01

Radioactive shales of Frasnian age in the Parnaiba Basin present high concentrations of organic matter. They correspond to a condensed section related to the Devonian maximum marine transgression. Combined geochemical, palynological and clay mineral data point out to a dominant algal contribution in the composition of the organic matter, as well as to anoxic depositional settings. This radioactive shale interval corresponds to the onset of a long-lasting, global anoxic event which was to be intensified in the Late Frasnian, and thus can be regarded as a marker for chronostratigraphic correlations. It includes the main source rocks of Devonian age in the Palaeozoic basins of north Brazil, and therefore represents a target of potential interest for hydrocarbon exploration. (authors). 16 refs., 10 figs., 1 tab., 17 photos

Geochemical characterization and miospore biochronostratigraphy of the Frasnian anoxic event in the Parnaiba basin, Northeast Brazil

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, R.; De Melo, J.H.G.; Alves, D.B. [Universidade Federal, Rio de Janeiro, RJ (Brazil); Loboziak, S. [Lille-1 Univ., 59 - Villeneuve-d`Ascq (France)

1995-12-31

Radioactive shales of Frasnian age in the Parnaiba Basin present high concentrations of organic matter. They correspond to a condensed section related to the Devonian maximum marine transgression. Combined geochemical, palynological and clay mineral data point out to a dominant algal contribution in the composition of the organic matter, as well as to anoxic depositional settings. This radioactive shale interval corresponds to the onset of a long-lasting, global anoxic event which was to be intensified in the Late Frasnian, and thus can be regarded as a marker for chronostratigraphic correlations. It includes the main source rocks of Devonian age in the Palaeozoic basins of north Brazil, and therefore represents a target of potential interest for hydrocarbon exploration. (authors). 16 refs., 10 figs., 1 tab., 17 photos.

Origin of oil shales

Energy Technology Data Exchange (ETDEWEB)

Weeks, W G

1923-01-01

The theory by Jones was questioned. Oil shales do not contain partly decomposed vegetable matter, and, where particles of vegetation are identified, they do not prove that kerogen was formed in its place. Some shales do contain free oil that can be extracted with solvents.

The shale gas potential of the Opalinus Clay and Posidonia Shale in Switzerland - A first assessment

International Nuclear Information System (INIS)

Leu, W.; Gautschi, A.

2014-01-01

There has been recent interest in the shale gas potential of the Opalinus Clay and Posidonia Shale (Middle and Lower Jurassic) below the Swiss Molasse Basin in the light of the future role of domestic gas production within the expected future energy shift of Switzerland and possible conflicts in underground use. The Opalinus Clay of northern Switzerland is a potential host rock for repositories of both high-level and low-to-intermediate level radioactive waste and the exploitation of shale gas resources within or below this formation would represent a serious conflict of use. Well data from northern Switzerland shows that these two formations are unsuitable for future shale gas recovery. They never reached the gas window during their burial history (maturity values are ≤ 0.6% R o ) and as a consequence never generated significant quantities of thermogenic gas. Geochemical data further shows that the average TOC values are in the range of 0.7%, i.e. clearly below accepted values of more than 1.5% for prospective shales. A review of available exploration data for the Opalinus Clay and Posidonia Shale in the deeper and western part of the Swiss Molasse Basin indicate that their shale gas potential may be substantial. The gross Posidonia Shale thickness increases from central Switzerland from less than 10 m to over 100 m in the Yverdon-Geneva area and is characterised by numerous bituminous intervals. A simplified shale gas resource calculation results for a geologically likely scenario in a technically recoverable gas volume of ∼120 billions m 3 . The current database for such estimates is small and as a consequence, the uncertainties are large. However, these first encouraging results support a more detailed exploration phase with specific geochemical and petrophysical analysis of existing rock and well log data. (authors)

The shale gas potential of the Opalinus Clay and Posidonia Shale in Switzerland - A first assessment

Energy Technology Data Exchange (ETDEWEB)

Leu, W. [Geoform Ltd, Villeneuve (Switzerland); Gautschi, A. [NAGRA, Wettingen (Switzerland)

2014-07-01

There has been recent interest in the shale gas potential of the Opalinus Clay and Posidonia Shale (Middle and Lower Jurassic) below the Swiss Molasse Basin in the light of the future role of domestic gas production within the expected future energy shift of Switzerland and possible conflicts in underground use. The Opalinus Clay of northern Switzerland is a potential host rock for repositories of both high-level and low-to-intermediate level radioactive waste and the exploitation of shale gas resources within or below this formation would represent a serious conflict of use. Well data from northern Switzerland shows that these two formations are unsuitable for future shale gas recovery. They never reached the gas window during their burial history (maturity values are ≤ 0.6% R{sub o}) and as a consequence never generated significant quantities of thermogenic gas. Geochemical data further shows that the average TOC values are in the range of 0.7%, i.e. clearly below accepted values of more than 1.5% for prospective shales. A review of available exploration data for the Opalinus Clay and Posidonia Shale in the deeper and western part of the Swiss Molasse Basin indicate that their shale gas potential may be substantial. The gross Posidonia Shale thickness increases from central Switzerland from less than 10 m to over 100 m in the Yverdon-Geneva area and is characterised by numerous bituminous intervals. A simplified shale gas resource calculation results for a geologically likely scenario in a technically recoverable gas volume of ∼120 billions m{sup 3}. The current database for such estimates is small and as a consequence, the uncertainties are large. However, these first encouraging results support a more detailed exploration phase with specific geochemical and petrophysical analysis of existing rock and well log data. (authors)

Reducing the greenhouse gas footprint of shale gas

International Nuclear Information System (INIS)

Wang Jinsheng; Ryan, David; Anthony, Edward J.

2011-01-01

Shale gas is viewed by many as a global energy game-changer. However, serious concerns exist that shale gas generates more greenhouse gas emissions than does coal. In this work the related published data are reviewed and a reassessment is made. It is shown that the greenhouse gas effect of shale gas is less than that of coal over long term if the higher power generation efficiency of shale gas is taken into account. In short term, the greenhouse gas effect of shale gas can be lowered to the level of that of coal if methane emissions are kept low using existing technologies. Further reducing the greenhouse gas effect of shale gas by storing CO 2 in depleted shale gas reservoirs is also discussed, with the conclusion that more CO 2 than the equivalent CO 2 emitted by the extracted shale gas could be stored in the reservoirs at significantly reduced cost. - Highlights: ► The long-term greenhouse gas footprint of shale gas is smaller than that of coal. ► Carbon capture and storage should be considered for fossil fuels including shale gas. ► Depleted shale gas fields could store more CO 2 than the equivalent emissions. ► Linking shale gas development with CO 2 storage could largely reduce the total cost.

A new Late Devonian genus with seed plant affinities.

Science.gov (United States)

Wang, Deming; Liu, Le

2015-02-26

Many ovules of Late Devonian (Famennian) seed plants have been well studied. However, because few taxa occur with anatomically preserved stems and/or petioles, the vascular system of these earliest spermatophytes is little understood and available data come mostly from Euramerica. There remains great controversy over the anatomical differentiation of Late Devonian and Carboniferous seed plant groups of Buteoxylonales, Calamopityales and Lyginopteridales. Protostele evolution of these early spermatophytes needs more research. A new taxon Yiduxylon trilobum gen. et sp. nov. with seed plant affinities has been discovered in the Upper Devonian (Famennian) Tizikou Formation of Hubei Province, China. It is represented by stems, helically arranged and bifurcate fronds with two orders of pinnae and planate pinnules. Both secondary pinnae and pinnules are borne alternately. Stems contain a small protostele with three primary xylem ribs possessing a single peripheral protoxylem strand. Thick secondary xylem displays multiseriate bordered pitting on the tangential and radial walls of the tracheids, and has biseriate to multiseriate and high rays. A narrow cortex consists of inner cortex without sclerotic nests and sparganum-type outer cortex with peripheral bands of vertically aligned sclerenchyma cells. Two leaf traces successively arise tangentially from each primary xylem rib and they divide once to produce four circular-oval traces in the stem cortex. Four vascular bundles occur in two C-shaped groups at each petiole base with ground tissue and peripheral bands of sclerenchyma cells. Yiduxylon justifies the assignment to a new genus mainly because of the protostele with protoxylem strands only near the periphery of primary xylem ribs, leaf trace origination and petiolar vascular supply structure. It shares many definitive characters with Calamopityales and Lyginopteridales, further underscoring the anatomical similarities among early seed plants. The primary vascular

Shale distillation

Energy Technology Data Exchange (ETDEWEB)

Jacomini, V V

1938-06-07

To produce valuable oils from shale by continuous distillation it is preheated by a heated fluid and introduced into a distilling retort from which the oil vapours and spent material are separately removed and the vapours condensed to recover the oil. The shale is preheated to 400 to 500/sup 0/F in the hopper by combustion gases from a flue and is fed in measured quantities to a surge drum, a loading chamber and surge drum, the latter two being connected to a steam pipe which equalises the pressure thereon. The material passes by two screw conveyors to a retort with deflector bars to scatter the material so that lean hot cycling gas flowing through a pipe is spread out as it makes its way upwardly through the shale and heats the oil so that it is driven off as vapour, collected in the lean gas and carried off through an outlet pipe. A measuring valve is provided at the bottom of a retort and cutter knives cut the spent shale and distribute cooling water thereto. The gases travel through heat exchangers and a condenser to an accumulator where the cycling gas is separated from the vapours, passed to compression, and preheated in a gas exchanger and spiral coils before it is returned to the retort. The oil passes to a storage tank by way of a unit tank in which oil vapours are recovered. Water is collected by a pipe in the tank bottom and returned by shaft to a retort.

Shale oil combustion

International Nuclear Information System (INIS)

Al-dabbas, M.A.

1992-05-01

A 'coutant' carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs

Shale oil combustion

Energy Technology Data Exchange (ETDEWEB)

Al-dabbas, M A

1992-05-01

A `coutant` carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs.

Distillation of shale in situ

Energy Technology Data Exchange (ETDEWEB)

de Ganahl, C F

1922-07-04

To distill buried shale or other carbon containing compounds in situ, a portion of the shale bed is rendered permeable to gases, and the temperature is raised to the point of distillation. An area in a shale bed is shattered by explosives, so that it is in a relatively finely divided form, and the tunnel is then blocked by a wall, and fuel and air are admitted through pipes until the temperature of the shale is raised to such a point that a portion of the released hydrocarbons will burn. When distillation of the shattered area takes place and the lighter products pass upwardly through uptakes to condensers and scrubbers, liquid oil passes to a tank and gas to a gasometer while heavy unvaporized products in the distillation zone collect in a drain, flow into a sump, and are drawn off through a pipe to a storage tank. In two modifications, methods of working are set out in cases where the shale lies beneath a substantially level surface.

Obtaining shale distillate free from sulphur

Energy Technology Data Exchange (ETDEWEB)

Heyl, G E

1917-09-14

A process whereby, from sulfur-containing shale, products free from sulfur may be obtained, consisting of mixing with the finely ground shale a portion of iron salts containing sufficient metal to unite with all the sulfur in the shale and form sulfide therewith, grinding the mixture to a fine state of subdivision and subsequently subjecting it to destructive distillation.

Distribution and Thermal Maturity of Devonian Carbonate Reservoir Solid Bitumen in Desheng Area of Guizhong Depression, South China

Directory of Open Access Journals (Sweden)

Yuguang Hou

2017-01-01

Full Text Available The distribution of solid bitumen in the Devonian carbonate reservoir from well Desheng 1, Guizhong Depression, was investigated by optical microscope and hydrocarbon inclusions analysis. Vb and chemical structure indexes measured by bitumen reflectance, laser Raman microprobe (LRM, and Fourier transform infrared spectroscopy (FTIR were carried out to determine the thermal maturity of solid bitumen. Based on the solid bitumen thermal maturity, the burial and thermal maturity history of Devonian carbonate reservoir were reconstructed by basin modeling. The results indicate that the fractures and fracture-related dissolution pores are the main storage space for the solid bitumen. The equivalent vitrinite reflectance of solid bitumen ranges from 3.42% to 4.43% converted by Vb (% and LRM. The infrared spectroscopy analysis suggests that there are no aliphatic chains detected in the solid bitumen which is rich in aromatics C=C chains (1431–1440 cm−1. The results of Vb (%, LRM, and FTIR analysis demonstrate that the solid bitumen has experienced high temperature and evolved to the residual carbonaceous stage. The thermal evolution of Devonian reservoirs had experienced four stages. The Devonian reservoirs reached the highest reservoir temperature 210–260°C during the second rapid burial-warming stage, which is the main period for the solid bitumen formation.

Unusual central Nevada geologic terranes produced by Late Devonian Antler orogeny and Alamo impact

Science.gov (United States)

Poole, Forrest G.; Sandberg, Charles

2015-01-01

This Special Paper is the product of nearly 25 years of geologic investigations. It is an exposition of two small areas, both less than 25 km east of the Mississippian Roberts Mountains allochthon, but each displaying a different, unique geologic terrane, previously undocumented in Nevada and perhaps in North America. One area, the Bisoni-McKay, at the south end of the Fish Creek Range, displays an olistostrome, shed eastward during the late Late Devonian (early Famennian) from a migrating Antler orogenic forebulge. The other, the Warm Springs–Milk Spring, at the south end of the Hot Creek Range, displays a deeper marine terrane affected by the early Late Devonian (middle Frasnian) Alamo impact.

A perspective on Canadian shale gas

Energy Technology Data Exchange (ETDEWEB)

Johnson, Mike; Davidson, Jim; Mortensen, Paul

2010-09-15

In a relatively new development over just the past few years, shale formations are being targeted for natural gas production. Based on initial results, there may be significant potential for shale gas in various regions of Canada, not only in traditional areas of conventional production but also non-traditional areas. However, there is much uncertainty because most Canadian shale gas production is currently in experimental or early developmental stages. Thus, its full potential will not be known for some time. If exploitation proves to be successful, Canadian shale gas may partially offset projected long-term declines in Canadian conventional natural gas production.

Oil shale utilization in Israel

International Nuclear Information System (INIS)

Kaiser, A.

1993-01-01

Geological surveys have confirmed the existence of substantial Israeli oil shale reserves. The proven reserves contain approximately 12 billion tons of available ores, and the potential is deemed to be much higher. Economic studies conducted by PAMA indicate promising potential for power generation via Israel oil shale combustion. Electric power from oil shale appears competitive with power generated from coal fired power plants located along the coast. PAMA's demonstration power plant has been in operation since the end of 1989. Based on the successful results of the first year of operation, PAMA and IEC are now engaged in the pre-project program for a 1000 MW commercial oil shale fired power plant, based on eight 120 MW units; the first unit is scheduled to begin operation in 1996

The late Middle Devonian fauna of Red Hill I, Nevada, and its paleobiogeographic implications

Directory of Open Access Journals (Sweden)

H.-P. Schultze

2010-08-01

Full Text Available The fauna of the Middle Devonian Red Hill I locality, Nevada, is unusual in the co-occurrence of a rich fish assemblage with a rich invertebrate one. Sponges are second in abundance of specimens and number of species only to the fishes and occur together with other invertebrates (conodonts, conulariids, dacryoconarid tentaculites, gastropods, bivalves, brachiopods, arthropods, and unidentifiable ammonoids and echinoderms. The invertebrates indicate a marine depositional paleoenvironment. The conodonts indicate a placement within the lower disparalis Zone, late Givetian. The fish assemblage is dominated by the antiarch Asterolepis. All the other fishes, acanthodians, actinopterygians and sarcopterygians, are less common. The closest biogeographic relationship of the fish fauna is with the Middle/Late Devonian fish fauna of the Baltic Region, followed by that of eastern Canada (Miguasha, Scotland and Iran. This distribution corresponds to the Devonian Euramerica faunal province with connection to eastern Gondwana (Iran and Australia. Localities with the same genera as Red Hill I are interpreted as marine with the exception of the Scottish localities. Asterolepis is the most widely distributed vertebrate genus, mostly marine, but it may be able to enter freshwater like Eusthenopteron if one accepts a freshwater depositional paleoenvironment for the Scottish localities. doi:10.1002/mmng.201000001

A Systems Approach to Identifying Exploration and Development Opportunities in the Illinois Basin: Digital Portifolio of Plays in Underexplored Lower Paleozoic Rocks [Part 1 of 2

Energy Technology Data Exchange (ETDEWEB)

Seyler, Beverly; Harris, David; Keith, Brian; Huff, Bryan; Lasemi, Yaghoob

2008-06-30

This study examined petroleum occurrence in Ordovician, Silurian and Devonian reservoirs in the Illinois Basin. Results from this project show that there is excellent potential for additional discovery of petroleum reservoirs in these formations. Numerous exploration targets and exploration strategies were identified that can be used to increase production from these underexplored strata. Some of the challenges to exploration of deeper strata include the lack of subsurface data, lack of understanding of regional facies changes, lack of understanding the role of diagenetic alteration in developing reservoir porosity and permeability, the shifting of structural closures with depth, overlooking potential producing horizons, and under utilization of 3D seismic techniques. This study has shown many areas are prospective for additional discoveries in lower Paleozoic strata in the Illinois Basin. This project implemented a systematic basin analysis approach that is expected to encourage exploration for petroleum in lower Paleozoic rocks of the Illinois Basin. The study has compiled and presented a broad base of information and knowledge needed by independent oil companies to pursue the development of exploration prospects in overlooked, deeper play horizons in the Illinois Basin. Available geologic data relevant for the exploration and development of petroleum reservoirs in the Illinois Basin was analyzed and assimilated into a coherent, easily accessible digital play portfolio. The primary focus of this project was on case studies of existing reservoirs in Devonian, Silurian, and Ordovician strata and the application of knowledge gained to future exploration and development in these underexplored strata of the Illinois Basin. In addition, a review of published reports and exploration in the New Albany Shale Group, a Devonian black shale source rock, in Illinois was completed due to the recent increased interest in Devonian black shales across the United States. The New

Is Estonian oil shale beneficial in the future?

International Nuclear Information System (INIS)

Reinsalu, Enno

1998-01-01

Oil shale mining production reached its maximum level of 31.35·10 6 tonnes per year in 1980. After the eighties there was a steady decline in mining. The first scientific prognoses of the inescapable decrease in oil shale mining were published in 1988. According to this, the Estonian oil shale industry would vanish in the third decade of the next century. From the beginning of the nineties, the consumption and export of electricity have dropped in Estonia. The minimum level of oil shale mining was 13.5·10 6 tonnes per year. This occurred in 1994/1995. Some increase in consumption of electric power and oil shale began at the end of 1995. Oil shale processing began to increase gradually in 1993. Oil shale is the most important fuel in Estonia today. In 1997, oil shale provided 76% of Estonia's primary energy supply and accounted for 57% of its economic value. Oil shale is the cheapest fuel in Estonia. Nowadays, oil shale provides an essential part of the fuel supply in Estonia because it is considerably cheaper than other fuels. Oil shale costs EEK 12.16 per G J. At the same time, coal costs EEK 23.41 per G J and peat costs EEK 14.80 per G J (year 1997). There are three important customers of oil shale: the electric power company Eesti Energia, the oil processing company Kiviter and the factory Kunda Nordic Cement. In 1995, the power company utilised 81% of the oil shale mass and 77% of its heating value. The state energy policy inhibits increases in the oil shale price even though the mining infrastructure is decaying. Government price policies subside oil shale processing. The energy of oil shale processing is 1.9 times cheaper than the heating value of raw oil shale for power stations. It could be considered as a state subsidisation of oil and cement export at the expense of electricity. The subsidy assigned to oil processing was of EEK 124·10 6 and to the cement industry of EEK 8.4·10 6 in year 1997 (based on heating value). State regulation of prices and

RUSSIA DOESN’T SUPPORT «SHALE REVOLUTION»

Directory of Open Access Journals (Sweden)

S. S. Zhiltsov

2015-01-01

Full Text Available Growth of volumes of production of shale gas in the USA compelled Russia to pay attention to this type of resourses. The interest to shale gas in Russia was limited to discussions at the level of experts and reflection of importance of this problem in statements of politicians. In the next years in Russia don't plan production of shale gas commercially. It is connected with existence in Russia of considerable reserves of traditional natural gas, absence of exact data of reserves of shale gas, high costs of production, and also environmental risks which accompany development of fields of shale gas.

The geology of Burnsville Cove, Bath and Highland Counties, Virginia

Science.gov (United States)

Swezey, Christopher; Haynes, John T.; Lambert, Richard A.; White, William B.; Lucas, Philip C.; Garrity, Christopher P.

2015-01-01

Burnsville Cove is a karst region in Bath and Highland Counties of Virginia. A new geologic map of the area reveals various units of limestone, sandstone, and siliciclastic mudstone (shale) of Silurian through Devonian age, as well as structural features such as northeast-trending anticlines and synclines, minor thrust faults, and prominent joints. Quaternary features include erosional (strath) terraces and accumulations of mud, sand, and gravel. The caves of Burnsville Cove are located within predominantly carbonate strata above the Silurian Williamsport Sandstone and below the Devonian Oriskany Sandstone. Most of the caves are located within the Silurian Tonoloway Limestone, rather than the Silurian-Devonian Keyser Limestone as reported previously.

Givetian (Middle Devonian) cladoxylopsid 'ferns' from Orkney, Northern Scotland

OpenAIRE

Berry, Christopher Mark; Hilton, Jason

2006-01-01

Two large fossil plants are described from the Givetian (Middle Devonian) Eday\\ud Flags, South Ronaldsay, Orkney Isles, northern Scotland. Fossils with branches joined to stems of\\ud this age are rare. Each specimen comprises a robust and tapering main trunk from which numerous\\ud closely spaced branches arise distally. Although poorly preserved such that generic identifications are\\ud not possible, both specimens display the characteristic architecture of the plant order Pseudosporochnales\\u...

Shale-brine-CO2 interactions and the long-term stability of carbonate-rich shale caprock

Science.gov (United States)

Ilgen, A.; Aman, M.; Espinoza, D. N.; Rodriguez, M. A.; Griego, J.; Dewers, T. A.; Feldman, J.; Stewart, T.; Choens, R. C., II

2017-12-01

Geological carbon storage (GCS) requires an impermeable caprock (e.g., shale) that prevents the upward migration and escape of carbon dioxide (CO2) from the subsurface. Geochemical alteration can occur at the caprock-reservoir rock interface, which could lead to the altering of the rock's mechanical properties, compromising the seal. We performed laboratory experiments on Mancos shale to quantify the coupled chemical-mechanical response of carbonate-rich shale in CO2-brine mixtures at conditions typical to GCS. We constructed geochemical models, calibrated them using laboratory results, and extended to time scales required for GCS. We observed the dissolution of calcite and kaolinite and the precipitation of gypsum and amorphous aluminum (hydr)oxide following the introduction of CO2. To address whether this mineral alteration causes changes in micro-mechanical properties, we examined altered Mancos shale using micro-mechanical (scratch) testing, measuring the scratch toughness of mm-scale shale lithofacies. The quartz-rich regions of the Mancos shale did not show significant changes in scratch toughness following 1-week alteration in a CO2-brine mixture. However, the scratch toughness of the calcite-rich, originally softer regions decreased by about 50%. These observations illustrate a coupled and localized chemical-mechanical response of carbonate-rich shale to the injection of CO2. This suggests a localized weakening of the caprock may occur, potentially leading to the development of preferential flow paths. The identification of vulnerable lithofacies within caprock and a characterization of mineralogical heterogeneity is imperative at prospective GCS sites. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE

Process for extracting oil shale

Energy Technology Data Exchange (ETDEWEB)

1920-08-22

A process is described for recovering bituminous material from oil shale, characterized in that the oil shale is extracted with wood spirits oil (byproduct of woodspirit rectification), if necessary in admixture with other solvents in the cold or the hot.

Shale Gas Technology. White Paper

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-09-15

Shale gas is extracted using horizontal drilling and hydraulic fracturing or 'fracking'. None of which are particularly new technologies or shale gas specific. In this white paper attention is paid to Horizontal drilling; Hydraulic fracturing or 'frackin'; Other 'unconventionals'; and Costs.

Assessment of potential unconventional lacustrine shale-oil and shale-gas resources, Phitsanulok Basin, Thailand, 2014

Science.gov (United States)

Schenk, Christopher J.; Charpentier, Ronald R.; Klett, Timothy R.; Mercier, Tracey J.; Tennyson, Marilyn E.; Pitman, Janet K.; Brownfield, Michael E.

2014-01-01

Using a geology-based assessment methodology, the U.S. Geological Survey assessed potential technically recoverable mean resources of 53 million barrels of shale oil and 320 billion cubic feet of shale gas in the Phitsanulok Basin, onshore Thailand.

Treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Ginet, J H

1921-03-09

Apparatus for the treatment of bituminous shales is described wherein a number of separate compartments are arranged in alignment and communicate with each other near the bottom thereof, each of the compartments being provided with outlets for the gases evolved therein, while agitators are arranged in each of the compartments, each agitator being composed of a number of shovels which sweep up the comminuted shale at their forward end and discharge it at their rearward end into the path of the next adjacent agitator.

Treating oil shale

Energy Technology Data Exchange (ETDEWEB)

Dolbear, S H

1921-01-04

Oil shale is treated for the separation of the valuable organic compounds, with a view to economy in subsequent destructive distillation, by grinding to powder, mixing with water to form a pulp, adding a small quantity of an oil liquid and aerating the mixture to form a froth containing the organic compounds. If the powdered shale contains sufficient free oil, the addition of oil to the pulp may be dispensed with. In some cases an electrolyte such as sulfuric acid may be added to the pulp.

Oil shale research related to proposed nuclear projects

Energy Technology Data Exchange (ETDEWEB)

Carpenter, H C; Sohns, H W; Dinneen, G U [Laramie Petroleum Research Center, Bureau of Mines, Department of the Interior, Laramie, WY (United States)

1970-05-15

The Bureau of Mines is conducting research to develop data pertinent to in situ retorting of oil shale fractured by a nuclear explosion or other means. Maximum utilization of the Green River oil shale found in Colorado, Utah, and Wyoming, at depths ranging from outcrops to several thousand feet, requires development of several methods of processing. Early research was devoted to developing processes for application to oil shale occurring at depths suitable for mining. In present research, the emphasis is on in situ retorting and recovery processes that would be more satisfactory for oil shales occurring at greater depths. Development of an in situ process depends upon finding or establishing sufficient permeability in the oil shale beds for the passage of fluids which serve as a heat carrier in bringing the oil shale to retorting temperature. Use of a nuclear explosive seems to offer the best chance for successfully fracturing the thicker and more deeply buried portions of the deposit to give the required permeability. Processing the very large quantity of broken and fractured oil shale that would be produced presents many problems which require new background data for their solution. This paper describes research the Bureau of Mines is conducting to develop pertinent data. Primarily this research involves laboratory determination of properties of oil shale, pilot scale investigation of retorting characteristics of ungraded broken shale, and underground combustion of shale fractured by pressure and chemical explosives. Application of the research results should aid in designing the oil recovery phase and provide an estimate of the quantity of oil that may be obtained in a nuclear experiment in oil shale. (author)

Oil shale research related to proposed nuclear projects

International Nuclear Information System (INIS)

Carpenter, H.C.; Sohns, H.W.; Dinneen, G.U.

1970-01-01

The Bureau of Mines is conducting research to develop data pertinent to in situ retorting of oil shale fractured by a nuclear explosion or other means. Maximum utilization of the Green River oil shale found in Colorado, Utah, and Wyoming, at depths ranging from outcrops to several thousand feet, requires development of several methods of processing. Early research was devoted to developing processes for application to oil shale occurring at depths suitable for mining. In present research, the emphasis is on in situ retorting and recovery processes that would be more satisfactory for oil shales occurring at greater depths. Development of an in situ process depends upon finding or establishing sufficient permeability in the oil shale beds for the passage of fluids which serve as a heat carrier in bringing the oil shale to retorting temperature. Use of a nuclear explosive seems to offer the best chance for successfully fracturing the thicker and more deeply buried portions of the deposit to give the required permeability. Processing the very large quantity of broken and fractured oil shale that would be produced presents many problems which require new background data for their solution. This paper describes research the Bureau of Mines is conducting to develop pertinent data. Primarily this research involves laboratory determination of properties of oil shale, pilot scale investigation of retorting characteristics of ungraded broken shale, and underground combustion of shale fractured by pressure and chemical explosives. Application of the research results should aid in designing the oil recovery phase and provide an estimate of the quantity of oil that may be obtained in a nuclear experiment in oil shale. (author)

Regressive transgressive cycle of Devonian sea in Uruguay verified by Palynology

International Nuclear Information System (INIS)

Da Silva, J.

1990-01-01

This work is about the results and conclusions of the populations palinomorphs study, carried out in Devonian formations in the center of Uruguay. The existence of a regressive transgressive cycle is verified by analyzing the vertical distribution of palinomorphs as well as is mentioned the presence of chintziest for the section studied - hoesphaeridium Cyathochitina kinds

Investigating the Potential Impacts of Energy Production in the Marcellus Shale Region Using the Shale Network Database

Science.gov (United States)

Brantley, S.; Brazil, L.

2017-12-01

The Shale Network's extensive database of water quality observations enables educational experiences about the potential impacts of resource extraction with real data. Through tools that are open source and free to use, researchers, educators, and citizens can access and analyze the very same data that the Shale Network team has used in peer-reviewed publications about the potential impacts of hydraulic fracturing on water. The development of the Shale Network database has been made possible through efforts led by an academic team and involving numerous individuals from government agencies, citizen science organizations, and private industry. Thus far, these tools and data have been used to engage high school students, university undergraduate and graduate students, as well as citizens so that all can discover how energy production impacts the Marcellus Shale region, which includes Pennsylvania and other nearby states. This presentation will describe these data tools, how the Shale Network has used them in developing lesson plans, and the resources available to learn more.

Experimental Study of Matrix Permeability of Gas Shale: An Application to CO2-Based Shale Fracturing

Directory of Open Access Journals (Sweden)

Chengpeng Zhang

2018-03-01

Full Text Available Because the limitations of water-based fracturing fluids restrict their fracturing efficiency and scope of application, liquid CO2 is regarded as a promising substitute, owing to its unique characteristics, including its greater environmental friendliness, shorter clean-up time, greater adsorption capacity than CH4 and less formation damage. Conversely, the disadvantage of high leak-off rate of CO2 fracturing due to its very low viscosity determines its applicability in gas shales with ultra-low permeability, accurate measurement of shale permeability to CO2 is therefore crucial to evaluate the appropriate injection rate and total consumption of CO2. The main purpose of this study is to accurately measure shale permeability to CO2 flow during hydraulic fracturing, and to compare the leak-off of CO2 and water fracturing. A series of permeability tests was conducted on cylindrical shale samples 38 mm in diameter and 19 mm long using water, CO2 in different phases and N2 considering multiple influencing factors. According to the experimental results, the apparent permeability of shale matrix to gaseous CO2 or N2 is greatly over-estimated compared with intrinsic permeability or that of liquid CO2 due to the Klinkenberg effect. This phenomenon explains that the permeability values measured under steady-state conditions are much higher than those under transient conditions. Supercritical CO2 with higher molecular kinetic energy has slightly higher permeability than liquid CO2. The leak-off rate of CO2 is an order of magnitude higher than that of water under the same injection conditions due to its lower viscosity. The significant decrease of shale permeability to gas after water flooding is due to the water block effect, and much longer clean-up time and deep water imbibition depth greatly impede the gas transport from the shale matrix to the created fractures. Therefore, it is necessary to substitute water-based fracturing fluids with liquid or super

Wangshangkia, a new Devonian ostracod genus from Dushan of Guizhou, South China

Science.gov (United States)

Song, Junjun; Gong, Yiming

2018-02-01

Wangshangkia, a new genus of Ostracoda, from the Late Devonian in Dushan of Guizhou, South China, is described. This genus belongs to the family Bairdiocyprididae Shaver, 1961 and includes two new species, i.e. Wangshangkia dushaniensis and W. bailouiensis. The new genus is characterized by a wide ventral carina with radial striae. It is reported from the Famennian of South China and disappeared just below the Devonian-Carboniferous boundary. Wangshangkia is essentially a benthic crawler and is restricted to the shallow-marine depositional environment with a low hydrodynamic condition. Wangshangkia: urn:lsid:zoobank.org:act:34BF01D4-D202-492D-8E27-BC508EF7EFFB W. dushaniensis: urn:lsid:zoobank.org:act:D267C362-7510-4D19-996B-EA1848D7D025 W. bailouiensis: urn:lsid:zoobank.org:act:FE988AA0-7363-4D9E-A5AB-1526C8DBCDD9

Towards a High-resolution Time Scale for the Early Devonian

Science.gov (United States)

Dekkers, M. J.; da Silva, A. C.

2017-12-01

High-resolution time scales are crucial to understand Earth's history in detail. The construction of a robust geological time scale, however, inevitably becomes increasingly harder further back in time. Uncertainties associated with anchor radiometric ages increase in size, not speaking of the mere presence of suitable datable strata. However, durations of stages can be tightly constrained by making use of cyclic expressions in sediments, an approach that revolutionized the Cenozoic time scale. When precisely determined durations are stitched together, ultimately, a very precise time scale is the result. For the Mesozoic and Paleozoic an astronomical solution as a tuning target is not available but the dominant periods of eccentricity, obliquity and precession are reasonably well constrained for the entire Phanerozoic which enables their detection by means of spectral analysis. Eccentricity is time-invariant and is used as the prime building block. Here we focus on the Early Devonian, on its lowermost three stages: the Lochkovian, Pragian and Emsian. The uncertainties on the Devonian stage boundaries are currently in the order of several millions of years. The preservation of climatic cycles in diagenetically or even anchimetamorphically affected successions, however, is essential. The fit of spectral peak ratios with those calculated for orbital cycles, is classically used as a strong argument for a preserved climatic signal. Here we use primarily the low field magnetic susceptibility (MS) as proxy parameter, supported by gamma-ray spectrometry to test for consistency. Continuous Wavelet Transform, Evolutive Harmonic Analysis, Multitaper Method, and Average Spectral Misfit are used to reach an optimal astronomical interpretation. We report on classic Early Devonian sections from the Czech Republic: the Pozar-CS (Lochkovian and Pragian), Pod Barrandovem (Pragian and Lower Emsian), and Zlichov (Middle-Upper Emsian). Also a Middle-Upper Emsian section from the US

Distillation of shale and other bituminous substances. [shale granules wetted, mixed with lime, heated; sulfur recovered

Energy Technology Data Exchange (ETDEWEB)

Noad, J

1912-09-23

A process is described for the treatment of shale and other bituminous substances containing sulfur and recovering desulfurized distillates. The process consists of first grinding the shale and mixing the granules obtained with a convenient liquid. The shale granules coated or covered with liquid and mixed with slacked lime are fed into a retort with a series of steps or their equivalent, made to descend, step by step, in such manner that they are continually agitated and heated. The volatile constituents escape through the coating or sheath of lime and are carried away at the upper part of the retort to a convenient condensing apparatus, the sulfur being retained by the sheath of lime and is discharged at the bottom of the retort with the spent shale and other impurities.

From success to persistence: Identifying an evolutionary regime shift in the diverse Paleozoic aquatic arthropod group Eurypterida, driven by the Devonian biotic crisis.

Science.gov (United States)

Lamsdell, James C; Selden, Paul A

2017-01-01

Mass extinctions have altered the trajectory of evolution a number of times over the Phanerozoic. During these periods of biotic upheaval a different selective regime appears to operate, although it is still unclear whether consistent survivorship rules apply across different extinction events. We compare variations in diversity and disparity across the evolutionary history of a major Paleozoic arthropod group, the Eurypterida. Using these data, we explore the group's transition from a successful, dynamic clade to a stagnant persistent lineage, pinpointing the Devonian as the period during which this evolutionary regime shift occurred. The late Devonian biotic crisis is potentially unique among the "Big Five" mass extinctions in exhibiting a drop in speciation rates rather than an increase in extinction. Our study reveals eurypterids show depressed speciation rates throughout the Devonian but no abnormal peaks in extinction. Loss of morphospace occupation is random across all Paleozoic extinction events; however, differential origination during the Devonian results in a migration and subsequent stagnation of occupied morphospace. This shift appears linked to an ecological transition from euryhaline taxa to freshwater species with low morphological diversity alongside a decrease in endemism. These results demonstrate the importance of the Devonian biotic crisis in reshaping Paleozoic ecosystems. © 2016 The Author(s). Evolution © 2016 The Society for the Study of Evolution.

Shale Gas Technology. White Paper

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-09-15

Shale gas is extracted using horizontal drilling and hydraulic fracturing or 'fracking'. None of which are particularly new technologies or shale gas specific. In this white paper attention is paid to Horizontal drilling; Hydraulic fracturing or 'frackin'; Other 'unconventionals'; and Costs.

Recovering valuable shale oils, etc

Energy Technology Data Exchange (ETDEWEB)

Engler, C

1922-09-26

A process is described for the recovery of valuable shale oils or tars, characterized in that the oil shale is heated to about 300/sup 0/C or a temperature not exceeding this essentially and then is treated with a solvent with utilization of this heat.

Preparing hydraulic cement from oil-shale slag

Energy Technology Data Exchange (ETDEWEB)

1921-11-19

A process for the preparation of hydraulic cementing material from oil shale or oil-shale slag according to Patent 411,584 is characterized by the fact that the oil-shale slag is added to burnt marl, blast-furnace slag, and the like, whereupon the mixture is milled to dust in the known way.

Thermally-driven Coupled THM Processes in Shales

Science.gov (United States)

Rutqvist, J.

2017-12-01

Temperature changes can trigger strongly coupled thermal-hydrological-mechanical (THM) processes in shales that are important to a number of subsurface energy applications, including geologic nuclear waste disposal and hydrocarbon extraction. These coupled processes include (1) direct pore-volume couplings, by thermal expansion of trapped pore-fluid that triggers instantaneous two-way couplings between pore fluid pressure and mechanical deformation, and (2) indirect couplings in terms of property changes, such as changes in mechanical stiffness, strength, and permeability. Direct pore-volume couplings have been studied in situ during borehole heating experiments in shale (or clay stone) formations at Mont Terri and Bure underground research laboratories in Switzerland and France. Typically, the temperature changes are accompanied with a rapid increase in pore pressure followed by a slower decrease towards initial (pre-heating) pore pressure. Coupled THM modeling of these heater tests shows that the pore pressure increases because the thermal expansion coefficient of the fluid is much higher than that of the porous clay stone. Such thermal pressurization induces fluid flow away from the pressurized area towards areas of lower pressure. The rate of pressure increase and magnitude of peak pressure depends on the rate of heating, pore-compressibility, and permeability of the shale. Modeling as well as laboratory experiments have shown that if the pore pressure increase is sufficiently large it could lead to fracturing of the shale or shear slip along pre-existing bedding planes. Another set of data and observations have been collected associated with studies related to concentrated heating and cooling of oil-shales and shale-gas formations. Heating may be used to enhance production from tight oil-shale, whereas thermal stimulation has been attempted for enhanced shale-gas extraction. Laboratory experiments on shale have shown that strength and elastic deformation

Shale gas: the water myth

Energy Technology Data Exchange (ETDEWEB)

O' Shea, Kerry [Dillon Consulting Limited (Canada)

2010-07-01

In recent years, due to the depletion of traditional fossil fuel resources and the rising price of energy, production from unconventional gas activities has increased. Large shale gas plays are available in Quebec but environmental concerns, mainly in terms of water resources, have been raised. The aim of this paper is to provide information on the impact of shale gas exploitation on water resources. It is shown herein that shale gas water use is not significant, the water use of 250 wells represents only 0.3% of the Quebec pulp and paper industry's water use, or 0.0004% of the flow of the St Lawrence. It is also shown that the environmental risk associated with fracking and drilling activities is low. This paper demonstrated that as long as industry practices conform to a well-designed regulatory framework, shale gas development in Quebec will have a low impact on water resources and the environment.

Nitrogen fixation by legumes in retorted shale

Energy Technology Data Exchange (ETDEWEB)

Hersman, L E; Molitoris, E; Klein, D A

1981-01-01

Although a soil-shale mixture was employed as the growth medium in this experiment, the results presentd are applicable to the proposed method of disposal mentioned earlier. Under field conditions, when covering the retorted shale with topsoil, some mixing of these materials might occur in the plant root region. In addition, it has been demonstrated that buried shale negatively affects enzyme activities in overburden surface soil. The occurrence of either of those events could affect symbiotic N/sub 2/ fixation in a manner similar to that reported in this paper. Researchers conclude that due to the varied effects of retorted shale on the legumes tested, further evaluation of other legumes may be necessary. Additional research would be required to determine which legumes have potential use for reclamation of retorted shale.

Preparation of cement from oil shale

Energy Technology Data Exchange (ETDEWEB)

1922-08-24

A process for preparing cement from oil shale is described. The simultaneous recovery of shale oil by heating the oil shale formed into briquets with finely ground lime or limestone in a stream of hot gases is characterized by the fact that live steam or fine drops of water as preserving and carbonization means is introduced into the furnace, at the place, where the temperature of the briquet reaches about 500 to 600/sup 0/ C.

Senate hearings whet interest in oil shale

Energy Technology Data Exchange (ETDEWEB)

Remirez, R

1967-06-05

Recent oil shale hearings by the U.S. Senate disclosed the proposed leasing rules for federal oil-shale lands. In addition, Oil Shale Corp. announced that the first commercial shale-oil processing plant would be on stream in 1970. Both these announcements are expected to create a stronger interest in what is possibly the greatest untapped natural wealth in the U.S. According to the leasing rules, development leases would involve the following phases: (1) the contractor would have a 10-yr limit to conduct a research and development program on the leased territory; and (2) upon completion of a successful research program, the Interior Department will make available to lease at least enough land to sustain commercial operation. The terms that applicants will have to meet are included in this report. At the Senate hearing, discussions ranged from opinions indicating that development of oil shale recovery was not immediately necessary to opinions urging rapid development. This report is concluded with a state-of-the-art review of some of the oil shale recovery processes.

Can the US shale revolution be duplicated in Europe?

International Nuclear Information System (INIS)

Saussay, Aurelien

2015-04-01

Over the past decade, the rapid increase in shale gas and shale oil production in the United States has profoundly changed energy markets in North America, and has led to a significant decrease in American natural gas prices. The possible existence of large shale deposits in Europe, mainly in France, Poland and the United Kingdom, has fostered speculation on whether the 'shale revolution', and its accompanying macro-economic impacts, could be duplicated in Europe. However, a number of uncertainties, notably geological, technological and regulatory, make this possibility unclear. We present a techno-economic model, SHERPA (Shale Exploitation and Recovery Projection and Analysis), to analyze the main determinants of the profitability of shale wells and plays. We calibrate our model using production data from the leading American shale plays. We use SHERPA to estimate three shale gas production scenarios exploring different sets of geological and technical hypotheses for the largest potential holder of shale gas deposits in Europe, France. Even considering that the geology of the potential French shale deposits is favorable to commercial extraction, we find that under assumptions calibrated on U.S. production data, natural gas could be produced at a high breakeven price of $8.6 per MMBtu, and over a 45 year time-frame have a net present value of $19.6 billion - less than 1% of 2012 French GDP. However, the specificities of the European context, notably high deposit depth and stricter environmental regulations, could increase drilling costs and further decrease this low profitability. We find that a 40% premium over American drilling costs would make shale gas extraction uneconomical. Absent extreme well productivity, it appears very difficult for shale gas extraction to have an impact on European energy markets comparable to the American shale revolution. (author)

The influence of shale gas on steamcracking

Energy Technology Data Exchange (ETDEWEB)

Rupieper, A. [Linde Engineering Dresden GmbH, Dresden (Germany)

2013-11-01

US shale gas reserves with more than 860 TCF (Source: U.S. Energy Information Administration study World Shale Gas Resources) account for 2 of the global largest reserves after China. In 7 areas of the US, these reserves are systematically explored, providing a significant amount of cheap natural gas source for decades. The ethane share, carried by such shale gas, can reach up to 16%. Ethane has been already in the past 2 most important feedstock for Steamcrackers, being the backbone of the Petrochemical Industry. Due to availability of vast shale gas, the US steamcracker industry is facing a shift from naphtha to shale gas ethane, as the margin of Ethylene produced from shale gas ethane is significantly larger than that of naphtha based Ethylene (app. + 630 USD/t Ethylene). As a consequence shale gas is ''the magic bullet'' incinerating investments into Steamcrackers and downstream plants for U.S petrochemical industry. Steamcracker Projects with an additional ethylene production capacity of more than 17 million tons/a by 2020 are announced or already under construction. Investments into downstream plants refining the C2 derivatives will follow or are already in planning/engineering phase. But the US market cannot absorb all related products, causing a significant export exposure, which will influence global trade flows for C2 derivatives and affect prices. This article presents the impact of shale gas ethane cracking on: - Trade flow of C2 derivatives; - By-product deficits; - Alternate C3+ derivative production routes; - Challenges related to engineering requirements and project execution for Steamcracker projects. (orig.)

The silurian and devonian vertebrates of Bolivia

Directory of Open Access Journals (Sweden)

1986-01-01

formas de amplia repartición (Rhenanidos, algunos Acanthodios, Actinopterygios de tipo Moythomasia, formas con afinidades transpacíficas (Acanthodios próximos de Sinacanthus y formas tal vez endémicas (Pucapampella, Zamponiopteron. Silurian and Devonian vertebrate remains are described from various localities in Bolivia. Most of the material occurs in concretions in the marine Devonian of the Altiplano and Subandean area, and some isolated specimens have been found in sandstones and lutites. The jawless vertebrates are known only from isolated thelodont scales which occur in the Uppermost Silurian or Lower Devonian of Seripona, Chuquisaca. All the other vertebrate remains belong to gnathosthomes, in particular to the acanthodians, placoderms, chondrichthyans and actinopterygians. The acanthodians are represented by some ischnacanthid dentigerous jaw bones and climatiid spines and shoulder girdles. They are fairly abundant and show no marked differences from acanthodian remains known elsewhere in the Siluro-Devonian of Europe and North America. However, some isolated spines are suggestive of the genus Sinacanthus, known from the Lower Devonian of China The placoderms are represented only by the rhenanid Bolivosteus chacomensis Goujet et al, known from two well preserved braincases. This genus closely resembles Gemuendina (Lower Devonian of Germany with respect to the overall shape of the braincase, but its shoulder girdle differs substantially. The chondrichthyans are the most abundant vertebrates in the Devonian of Bolivia They are represented by isolated spines and endoskeletal elements lined with prismatic calcified cartilage Among them, some peculiar occipital regions of braincases are referred here to Pucapampella rodrigae n.g , n sp. These brain-cases differ from all other known Devonian chondrichthyan braincases in showing a ventrally continuous occipital fissure which completely separates the occiput from the rest of the brain-case. The strongly vaulted

Shale gas - the story of a deception

International Nuclear Information System (INIS)

Ambroise, Jacques

2013-01-01

This bibliographical sheet presents a book which aims at informing citizen about the irreversible consequences of shale gas exploitation on the environment, and about the economical and social aspects of an exploitation of this energy on a large scale. The author highlights the technical and environmental problems raised by hydraulic fracturing, outlines the complexity of the regulatory, legal and administrative framework, discusses the arguments which support shale gas exploitation, and outlines the importance of and energy transition without shale gas. The author notably outlines the conflicts of interest which pervert the debate on shale gas, notably within the French National Assembly

Black shales and naftogenesis. A review

International Nuclear Information System (INIS)

Yudovich, Yu.E.; Ketris, M.P.

1993-01-01

A genetic relation between petroleum plus hydrocarbon gases and bio organic authigenic matter has been well established. As black shales are enriched in organic matter they may serve as potential petroleum beds on the depths suitable for petroleum generation (2-5 km). The calculations made by petroleum geologists showed that hydrocarbon amounts generated by black shales made up to one fifth of the initial organic matter at the end of MK-2 stage of catagenesis. Consequently, black shales may serve as the main oil producers in many sedimentary basins. Petroleum generation in black shales has some peculiarities. Abundant masses of organic matter generate huge amounts of hydrocarbon gases which in turn produce anomalous high bed pressures followed by pulse cavitation effect. Bed pressures 1.5 times higher than normal lithostatic pressure have been detected in oil-bearing black shales of the Cis-Caucasus on the depth of 2.0-2.5 km, along with very high (6 degrees per 100 m) geothermal gradient. According to Stavropol oil geologists, there occurs an effect of rock-by-fluid-destruction after fluid pressure has greatly exceeded the lithostatic pressure. Stress tensions discharge by impulses and cracks may appear with a rate of 0.3-0.7 of the sound speed. Cavitation of gaseous bubbles is produced by sharp crack extension. Such cavitation accounts for impact waves and increased local pressure and temperature. Such an increase, in turn, fastens petroleum generation and new rock cracking. The effect of over-pressed rocks associated with black shales may serve as a process indicator. That is why the geophysical methods detect enhanced specific gravity and decreased porosity zones in such black shales. Cracks and petroleum accumulation occur on the flanks of such zones of rock-by-fluid-destruction. Some black shales may be petroleum-productive due to enhanced uranium content. There exist ideas about uranium-derived heat or radiolytic effects on the petroleum generation. Such

Different Methods of Predicting Permeability in Shale

DEFF Research Database (Denmark)

Mbia, Ernest Ncha; Fabricius, Ida Lykke; Krogsbøll, Anette

by two to five orders of magnitudes at lower vertical effective stress below 40 MPa as the content of clay minerals increases causing heterogeneity in shale material. Indirect permeability from consolidation can give maximum and minimum values of shale permeability needed in simulating fluid flow......Permeability is often very difficult to measure or predict in shale lithology. In this work we are determining shale permeability from consolidation tests data using Wissa et al., (1971) approach and comparing the results with predicted permeability from Kozeny’s model. Core and cuttings materials...... effective stress to 9 μD at high vertical effective stress of 100 MPa. The indirect permeability calculated from consolidation tests falls in the same magnitude at higher vertical effective stress, above 40 MPa, as that of the Kozeny model for shale samples with high non-clay content ≥ 70% but are higher...

An exceptionally preserved Late Devonian actinopterygian provides a new model for primitive cranial anatomy in ray-finned fishes

Science.gov (United States)

Giles, Sam; Darras, Laurent; Clément, Gaël; Blieck, Alain; Friedman, Matt

2015-01-01

Actinopterygians (ray-finned fishes) are the most diverse living osteichthyan (bony vertebrate) group, with a rich fossil record. However, details of their earliest history during the middle Palaeozoic (Devonian) ‘Age of Fishes' remains sketchy. This stems from an uneven understanding of anatomy in early actinopterygians, with a few well-known species dominating perceptions of primitive conditions. Here we present an exceptionally preserved ray-finned fish from the Late Devonian (Middle Frasnian, ca 373 Ma) of Pas-de-Calais, northern France. This new genus is represented by a single, three-dimensionally preserved skull. CT scanning reveals the presence of an almost complete braincase along with near-fully articulated mandibular, hyoid and gill arches. The neurocranium differs from the coeval Mimipiscis in displaying a short aortic canal with a distinct posterior notch, long grooves for the lateral dorsal aortae, large vestibular fontanelles and a broad postorbital process. Identification of similar but previously unrecognized features in other Devonian actinopterygians suggests that aspects of braincase anatomy in Mimipiscis are apomorphic, questioning its ubiquity as stand-in for generalized actinopterygian conditions. However, the gill skeleton of the new form broadly corresponds to that of Mimipiscis, and adds to an emerging picture of primitive branchial architecture in crown gnathostomes. The new genus is recovered in a polytomy with Mimiidae and a subset of Devonian and stratigraphically younger actinopterygians, with no support found for a monophyletic grouping of Moythomasia with Mimiidae. PMID:26423841

Oil shale : could Shell's experimental oil shale technology be adapted to Alberta's bitumen carbonates?

Energy Technology Data Exchange (ETDEWEB)

Roche, P.

2006-07-01

Although Shell has been trying to develop technologies to economically extract oil from shale containing kerogen for the last 25 years, the volume of oil Shell produced from its Mahogany Research Project in Colorado has added up to less than 2500 bbls in total, and the company has recently devoted $400 million to purchase leases on carbonate reservoirs in Alberta. This article examined whether or not the technologies developed by Shell for oil shales could be used to profitably extract bitumen from carbonates. Extracting bitumen from carbonates may be easier than producing oil from shale, as the resource in carbonates is already oil, whereas the oil in oil shale is actually kerogen, which needs to be chemically cracked at extremely high temperatures. Although the technical feasibility of an in situ cracking process has been proven, work remains to be done before Shell can invest in a commercial-scale oil shale project. Challenges to oil shale production include preventing groundwater from entering target zones and keeping produced fluids out of the groundwater. However, a freeze wall test has recently been designed where chilled liquid is circulated through a closed-loop pipe system to freeze formation water, sealing off an area about the size of a football field from the surrounding strata. The energy requirements of the process that Shell is testing to produce shale oil in Colorado remain unprofitably high, as higher temperatures are necessary for thermal cracking. Shell has yet to make a decision as to what energy sources it will use to make the production process economically viable. An energy conservation group in Colorado has claimed that production of 100,000 bbls of shale oil would require the largest power plant in Colorado history. 2 figs.

New U-Pb zircon ages and the duration and division of Devonian time

Science.gov (United States)

Tucker, R.D.; Bradley, D.C.; Ver Straeten, C.A.; Harris, A.G.; Ebert, J.R.; McCutcheon, S.R.

1998-01-01

Newly determined U-Pb zircon ages of volcanic ashes closely tied to biostratigraphic zones are used to revise the Devonian time-scale. They are: 1) 417.6 ?? 1.0 Ma for an ash within the conodont zone of Icriodus woschmidti/I. w. hesperius Lochkovian); 2) 408.3 ?? 1.9 Ma for an ash of early Emsian age correlated with the conodont zones of Po. dehiscens--Lower Po. inversus; 3) 391.4 ?? 1.8 Ma for an ash within the Po. c. costatus Zone and probably within the upper half of the zone (Eifelian); and 4) 381.1 ?? 1.3 Ma for an ash within the range of the Frasnian conodont Palmatolepis punctata (Pa. punctata Zone to Upper Pa. hassi Zone). U-Pb zircon ages for two rhyolites bracketing a palyniferous bed of the pusillites-lepidophyta spore zone, are dated at 363.8 ?? 2.2 Ma and 363 ?? 2.2 Ma and 363.4 ?? 1.8 Ma, respectively, suggesting an age of ~363 Ma for a level within the late Famennian Pa. g. expansa Zone. These data, together with other published zircon ages, suggest that the base and top of the Devonian lie close to 418 Ma and 362 Ma, respectively, thus lengthening the period of ~20% over current estimates. We suggest that the duration of the Middle Devonian (Eifelian and Givitian) is rather brief, perhaps no longer than 11.5 Myr (394 Ma-382.5 Ma), and that the Emsian and Famennian are the longest stages in the period with estimated durations of ~15.5 Myr and 14.5 Myr, respectively.

Comparative acute toxicity of shale and petroleum derived distillates.

Science.gov (United States)

Clark, C R; Ferguson, P W; Katchen, M A; Dennis, M W; Craig, D K

1989-12-01

In anticipation of the commercialization of its shale oil retorting and upgrading process, Unocal Corp. conducted a testing program aimed at better defining potential health impacts of a shale industry. Acute toxicity studies using rats and rabbits compared the effects of naphtha, Jet-A, JP-4, diesel and "residual" distillate fractions of both petroleum derived crude oils and hydrotreated shale oil. No differences in the acute oral (greater than 5 g/kg LD50) and dermal (greater than 2 g/kg LD50) toxicities were noted between the shale and petroleum derived distillates and none of the samples were more than mildly irritating to the eyes. Shale and petroleum products caused similar degrees of mild to moderate skin irritation. None of the materials produced sensitization reactions. The LC50 after acute inhalation exposure to Jet-A, shale naphtha, (greater than 5 mg/L) and JP-4 distillate fractions of petroleum and shale oils was greater than 5 mg/L. The LC50 of petroleum naphtha (greater than 4.8 mg/L) and raw shale oil (greater than 3.95 mg/L) also indicated low toxicity. Results demonstrate that shale oil products are of low acute toxicity, mild to moderately irritating and similar to their petroleum counterparts. The results further demonstrate that hydrotreatment reduces the irritancy of raw shale oil.

Radioactive contamination of oil produced from nuclear-broken shale

International Nuclear Information System (INIS)

Arnold, W.D.; Crouse, D.J.

1970-01-01

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

A review on technologies for oil shale surface retort

International Nuclear Information System (INIS)

Pan, Y.; Zhang, X.; Liu, S.; Yang, S.A.; Ren, N.

2012-01-01

In recent years, with the shortage of oil resources and the continuous increase in oil prices, oil shale has seized much more attention. Oil shale is a kind of important unconventional oil and gas resources. Oil shale resources are plentiful according to the proven reserves in places. And shale oil is far richer than crude oil in the world. Technology processing can be divided into two categories: surface retorting and in-situ technology. The process and equipment of surface retorting are more mature, and are still up to now, the main way to produce shale oil from oil shale. According to the variations of the particle size, the surface retorting technologies of oil shale can be notified and classified into two categories such as lump shale process and particulate shale process. The lump shale processes introduced in this article include the Fushun retorting technology, the Kiviter technology and the Petrosix technology; the particulate processes include the Gloter technology, the LR technology, the Tosco-II technology, the ATP (Alberta Taciuk Process) technology and the Enefit-280 technology. After the thorough comparison of these technologies, we can notice that, this article aim is to show off that : the particulate process that is environmentally friendly, with its low cost and high economic returns characteristics, will be the major development trend; Combined technologies of surface retorting technology and other oil producing technology should be developed; the comprehensive utilization of oil shale should be considered during the development of surface retorting technology, meanwhile the process should be harmless to the environment. (author)

Radioactive contamination of oil produced from nuclear-broken shale

Energy Technology Data Exchange (ETDEWEB)

Arnold, W D; Crouse, D J

1970-05-15

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

Oil shale mines and their realizable production

International Nuclear Information System (INIS)

Habicht, K.

1994-01-01

The production of Estonian oil shale depends on its marketing opportunities. The realizable production is a function of the oil shale price, which in turn depends on production costs. The latter are dependent on which mines are producing oil shale and on the volume of production. The purpose of the present article is to analyze which mines should operate under various realizable production scenarios and what should be their annual output so that the total cost of oil shale production (including maintenance at idle mines) is minimized. This paper is also targeted at observing the change in the average production cost per ton of oil shale depending on the realizable output. The calculations are based on data for the first four months of 1993, as collected by N. Barabaner (Estonian Academy of Sciences, Institute of Economy). The data include the total production volume and production cost from the mines of RE 'Eesti Polevkivi' (State Enterprise 'Estonian Oil Shale'). They also project expenses from mine closings in case of conservation. The latter costs were allocated among mines in direct proportion to their respective number of employees. (author)

Shale-oil-derived additives for fuel oils

International Nuclear Information System (INIS)

Raidma, E.; Leetsman, L.; Muoni, R.; Soone, Y.; Zhiryakov, Y.

2002-01-01

Studies have shown that the oxidation, wearing, and anticorrosive properties of shale oil as an additive to liquid fuels and oils enable to improve the conditions of their use. Studies conducted by Institute of Oil Shale have shown that it is possible, on the basis of shale oil produced by Viru Keemia Grupp AS (Viru Chemistry Group Ltd.) and, particularly, on the basis of its fractions 230-320 and 320-360 deg C to produce efficient and stable additives for liquid fuels to improve their combustion and storage properties. In the production of additives from shale oil the prerequisite taken into account is its complexity of composition and high concentration of neutral and phenolic oxygen compounds. Additives produced from shale oil have multifunctional properties which enable to improve operational data of liquid fuels and to increase the power of diesel engines and boilers. (author)

Chemical examination of the organic matter in oil shales

Energy Technology Data Exchange (ETDEWEB)

Robertson, J B

1914-01-01

The analyses of Broxburn (Scotland), Pumpherston (Scotland), Armadale (Scotland), Australian, and Knightsbridge oil shales were given. Also, the action of nitric acid and solvents on some of the oil shales was determined. Carbon-hydrogen ratios of the oil shales varied from 6 to more than 8, and the shales with the lowest ratio (most hydrogen per carbon) produced the largest amount of oil from a given amount of organic matter. There was little resinous material in the oil shales, and most of the organic matter was insoluble in organic solvents. Nitric acid oxidized Australian torbanite, Broxburn shale, New Battle cannel coal (Scotland), and Glenfullock peat to organic acids. The hydrogen content of the organic acids obtained by oxidizing the following materials increased from ordinary coal to cannel coal to peat to Broxburn shale to torbanite. The organic substance in oil shale is a decomposition product of vegetable matter similar to that found in peat and cannel coal, and it was produced by a definite combination of external conditions.

Shale Gas in Europe: pragmatic perspectives and actions

Science.gov (United States)

Hübner, A.; Horsfield, B.; Kapp, I.

2012-10-01

Natural gas will continue to play a key role in the EU's energy mix in the coming years, with unconventional gas' role increasing in importance as new resources are exploited worldwide. As far as Europe's own shale gas resources are concerned, it is especially the public's perception and level of acceptance that will make or break shale gas in the near-term. Both the pros and cons need to be discussed based on factual argument rather than speculation. Research organizations such as ours (GFZ German Research Centre for Geosciences) have an active and defining role to play in remedying this deficiency. As far as science and technology developments are concerned, the project "Gas Shales in Europe" (GASH) and the shale gas activities of "GeoEnergie" (GeoEn) are the first major initiatives in Europe focused on shale gas. Basic and applied geoscientific research is conducted to understand the fundamental nature and interdependencies of the processes leading to shale gas formation. When it comes to knowledge transfer, the perceived and real risks associated with shale gas exploitation need immediate evaluation in Europe using scientific analysis. To proactively target these issues, the GFZ and partners are launching the European sustainable Operating Practices (E-SOP) Initiative for Unconventional Resources. The web-based Shale Gas Information Platform (SHIP) brings these issues into the public domain.

Shale Gas in Europe: pragmatic perspectives and actions

Directory of Open Access Journals (Sweden)

Horsfield B.

2012-10-01

Full Text Available Natural gas will continue to play a key role in the EU’s energy mix in the coming years, with unconventional gas’ role increasing in importance as new resources are exploited worldwide. As far as Europe’s own shale gas resources are concerned, it is especially the public’s perception and level of acceptance that will make or break shale gas in the near-term. Both the pros and cons need to be discussed based on factual argument rather than speculation. Research organizations such as ours (GFZ German Research Centre for Geosciences have an active and defining role to play in remedying this deficiency. As far as science and technology developments are concerned, the project “Gas Shales in Europe” (GASH and the shale gas activities of “GeoEnergie” (GeoEn are the first major initiatives in Europe focused on shale gas. Basic and applied geoscientific research is conducted to understand the fundamental nature and interdependencies of the processes leading to shale gas formation. When it comes to knowledge transfer, the perceived and real risks associated with shale gas exploitation need immediate evaluation in Europe using scientific analysis. To proactively target these issues, the GFZ and partners are launching the European sustainable Operating Practices (E-SOP Initiative for Unconventional Resources. The web-based Shale Gas Information Platform (SHIP brings these issues into the public domain.

Improvements in shale retorts

Energy Technology Data Exchange (ETDEWEB)

Thomson, A C

1915-05-01

This invention has reference to shale retorts and particularly related to the discharge of the spent material from the bottom of retorts or gas producers for the destructive distillation of shale, coal or other bituminous substances. It consists in the combination of a blade and means for rocking the same, a bottom piece or table, holes or slots in the same, a passage in the front brick-work of the retort, and a hopper with discharge doors.

The Cannery Formation--Devonian to Early Permian arc-marginal deposits within the Alexander Terrane, Southeastern Alaska

Science.gov (United States)

Karl, Susan M.; Layer, Paul W.; Harris, Anita G.; Haeussler, Peter J.; Murchey, Benita L.

2011-01-01

The Cannery Formation consists of green, red, and gray ribbon chert, siliceous siltstone, graywacke-chert turbidites, and volcaniclastic sandstone. Because it contains early Permian fossils at and near its type area in Cannery Cove, on Admiralty Island in southeastern Alaska, the formation was originally defined as a Permian stratigraphic unit. Similar rocks exposed in Windfall Harbor on Admiralty Island contain early Permian bryozoans and brachiopods, as well as Mississippian through Permian radiolarians. Black and green bedded chert with subordinate lenses of limestone, basalt, and graywacke near Kake on Kupreanof Island was initially correlated with the Cannery Formation on the basis of similar lithology but was later determined to contain Late Devonian conodonts. Permian conglomerate in Keku Strait contains chert cobbles inferred to be derived from the Cannery Formation that yielded Devonian and Mississippian radiolarians. On the basis of fossils recovered from a limestone lens near Kake and chert cobbles in the Keku Strait area, the age of the Cannery Formation was revised to Devonian and Mississippian, but this revision excludes rocks in the type locality, in addition to excluding bedded chert on Kupreanof Island east of Kake that contains radiolarians of Late Pennsylvanian and early Permian age. The black chert near Kake that yielded Late Devonian conodonts is nearly contemporaneous with black chert interbedded with limestone that also contains Late Devonian conodonts in the Saginaw Bay Formation on Kuiu Island. The chert cobbles in the conglomerate in Keku Strait may be derived from either the Cannery Formation or the Saginaw Bay Formation and need not restrict the age of the Cannery Formation, regardless of their source. The minimum age of the Cannery Formation on both Admiralty Island and Kupreanof Island is constrained by the stratigraphically overlying fossiliferous Pybus Formation, of late early and early late Permian age. Because bedded radiolarian

Process for refining shale bitumen

Energy Technology Data Exchange (ETDEWEB)

Plauson, H

1920-09-19

A process is disclosed for refining shale bitumen for use as heavy mineral oil, characterized by mixtures of blown hard shale pitch and heavy mineral oil being blown with hot air at temperatures of 120 to 150/sup 0/ with 1 to 3 percent sulfur, and if necessary with 0.5 to 3 percent of an aldehyde.

Distilling shale and the like

Energy Technology Data Exchange (ETDEWEB)

Gee, H T.P.

1922-02-23

In distilling shale or like bituminous fuels by internal heating with hot gas obtained by the gasifying of the shale residues with air or steam or a mixture of these, the amount and temperature of the gaseous distilling medium is regulated between the gasifying and the distilling chambers, by the introduction of cold gas or air.

Lower and Middle Devonian Malvinokaffric ostracods from the Precordillera Basin of San Juan, Argentina

Science.gov (United States)

Salas, María J.; Rustán, Juan J.; Sterren, Andrea F.

2013-08-01

Ostracod from the upper Lower to Middle Devonian rocks of the Argentine Precordillera Basin (Talacasto and Punta Negra formations) are studied. One new genus Pircawayra nov. gen., and five species (including three new: Pircawayra gigantea nov. gen. and sp., Lapazites trinodis nov. sp. and Keslingiella? teresae nov. sp.) are defined. The recorded ostracod fauna closely resembles that coeval from Bolivia and South Africa, exhibiting a remarkable endemism, not only at the genus level, but also at the species level. In addition to its low-diversity, the Malvinokaffric ostracod association is also characterized by having large, thick, coarsely ornamented and swollen valves. The similar ostracod composition from the Andean and South African basins suggests faunal exchange between these two areas. Based on the ostracod faunas, the Malvinokaffric Realm is clearly recognizable at least up to the Middle Devonian.

How lithology and climate affect REE mobility and fractionation along a shale weathering transect of the Susquehanna Shale Hills Critical Zone Observatory

Science.gov (United States)

Ma, L.; Jin, L.; Dere, A. L.; White, T.; Mathur, R.; Brantley, S. L.

2012-12-01

Shale weathering is an important process in global elemental cycles. Accompanied by the transformation of bedrock into regolith, many elements including rare earth elements (REE) are mobilized primarily by chemical weathering in the Critical Zone. Then, REE are subsequently transported from the vadose zone to streams, with eventual deposition in the oceans. REE have been identified as crucial and strategic natural resources; and discovery of new REE deposits will be facilitated by understanding global REE cycles. At present, the mechanisms and environmental factors controlling release, transport, and deposition of REE - the sources and sinks - at Earth's surface remain unclear. Here, we present a systematic study of soils, stream sediments, stream waters, soil water and bedrock in six small watersheds that are developed on shale bedrock in the eastern USA to constrain the mobility and fractionation of REE during early stages of chemical weathering. The selected watersheds are part of the shale transect established by the Susquehanna Shale Hills Observatory (SSHO) and are well suited to investigate weathering on shales of different compositions or within different climate regimes but on the same shale unit. Our REE study from SSHO, a small gray shale watershed in central Pennsylvania, shows that up to 65% of the REE (relative to parent bedrock) is depleted in the acidic and organic-rich soils due to chemical leaching. Both weathering soil profiles and natural waters show a preferential removal of middle REE (MREE: Sm to Dy) relative to light REE (La to Nd) and heavy REE (Ho to Lu) during shale weathering, due to preferential release of MREE from a phosphate phase (rhabdophane). Strong positive Ce anomalies observed in the regolith and stream sediments point to the fractionation and preferential precipitation of Ce as compared to other REE, in the generally oxidizing conditions of the surface environments. One watershed developed on the Marcellus black shale in

Lower Devonian lithofacies and palaeoenvironments in the southwestern margin of the East European Platform (Ukraine, Moldova and Romania

Directory of Open Access Journals (Sweden)

Natalia Radkovets

2016-11-01

Full Text Available Lower Devonian palaeoshelf deposits extend along the western margin of the East European Platform from the Baltic Sea to the Black Sea. These deposits have been studied on the territory of Ukraine (Volyn-Podillyan Plate, Dobrogean Foredeep and correlated with coeval deposits in Moldova and Romania (Moldovian Platform. The investigation of the Lower Devonian deposits, their thickness, petrographic and lithological characteristics allowed reconstruction of two types of lithofacies and distinguishing two different depositional environments. The first lithofacies belonging to the Lochkovian stage, consists of clayey-carbonate rocks and represents a continuation of the Upper Silurian marine strata. The other lithofacies encompassing the Pragian–Emsian comprises terrigenous reddish-brown rocks, which are roughly equivalent to the Old Red Sandstone, completes the Lower Devonian section. Establishing the occurrence and thickness distribution of the terrigenous lithofacies across the study area is important, because it forms potential reservoir rocks for both conventional and unconventional (tight gas hydrocarbons. Gas accumulation in these reservoir rocks has been discovered at the Lokachi field.

Maquoketa Shale Caprock Integrity Evaluation

Energy Technology Data Exchange (ETDEWEB)

Leetaru, Hannes

2014-09-30

The Knox Project objective is to evaluate the potential of formations within the Cambrian-Ordovician strata above the Mt. Simon Sandstone (St. Peter Sandstone and Potosi Dolomite) as potential targets for carbon dioxide (CO2) sequestration in the Illinois and Michigan Basins. The suitability of the St. Peter Sandstone and Potosi Dolomite to serve as reservoirs for CO2 sequestration is discussed in separate reports. In this report the data gathered from the Knox project, the Illinois Basin – Decatur Project (IBDP) and Illinois Industrial Carbon Capture and Sequestration project (IL-ICCS) are used to make some conclusions about the suitability of the Maquoketa shale as a confining layer for CO2 sequestration. These conclusions are then upscaled to basin-wide inferences based on regional knowledge. Data and interpretations (stratigraphic, petrophysical, fractures, geochemical, risk, seismic) applicable to the Maquoketa Shale from the above mentioned projects was inventoried and summarized. Based on the analysis of these data and interpretations, the Maquoketa Shale is considered to be an effective caprock for a CO2 injection project in either the Potosi Dolomite or St. Peter Sandstone because it has a suitable thickness (~200ft. ~61m), advantageous petrophysical properties (low effective porosity and low permeability), favorable geomechanical properties, an absence of observable fractures and is regionally extensive. Because it is unlikely that CO2 would migrate upward through the Maquoketa Shale, CO2, impact to above lying fresh water aquifers is unlikely. Furthermore, the observations indicate that CO2 injected into the St. Peter Sandstone or Potosi Dolomite may never even migrate up into the Maquoketa Shale at a high enough concentrations or pressure to threaten the integrity of the caprock. Site specific conclusions were reached by unifying the data and conclusions from the IBDP, ICCS and the Knox projects. In the Illinois Basin, as one looks further away from

Intelligent fracture creation for shale gas development

KAUST Repository

Douglas, Craig C.

2011-05-14

Shale gas represents a major fraction of the proven reserves of natural gas in the United States and a collection of other countries. Higher gas prices and the need for cleaner fuels provides motivation for commercializing shale gas deposits even though the cost is substantially higher than traditional gas deposits. Recent advances in horizontal drilling and multistage hydraulic fracturing, which dramatically lower costs of developing shale gas fields, are key to renewed interest in shale gas deposits. Hydraulically induced fractures are quite complex in shale gas reservoirs. Massive, multistage, multiple cluster treatments lead to fractures that interact with existing fractures (whether natural or induced earlier). A dynamic approach to the fracturing process so that the resulting network of reservoirs is known during the drilling and fracturing process is economically enticing. The process needs to be automatic and done in faster than real-time in order to be useful to the drilling crews.

Shale gas. Opportunities and challenges for European energy markets

Energy Technology Data Exchange (ETDEWEB)

De Joode, J.; Plomp, A.J.; Ozdemir, O. [ECN Policy Studies, Petten (Netherlands)

2013-02-15

The outline of the presentation shows the following elements: Introduction (Shale gas revolution in US and the situation in the EU); What could be the impact of potential shale gas developments on the European gas market?; How may shale gas developments affect the role of gas in the transition of the power sector?; and Key messages. The key messages are (1) Prospects for European shale gas widely differ from US case (different reserve potential, different competition, different market dynamics); (2) Shale gas is unlikely to be a game changer in Europe; and (3) Impact of shale gas on energy transition in the medium and long term crucially depends on gas vs. coal prices and the 'penalty' on CO2 emissions.

Discovery of the fossiliferous Cu Brei Formation (Lower Devonian) in the Kon Tum Block (South Viet Nam)

Science.gov (United States)

Thanh, Tong-Dzuy; Duyen, Than Duc; Hung, Nguyen Huu; My, Bui Phu

2007-01-01

Lower Devonian corals and stromatoporoids have recently been discovered in limestones among low grade metamorphic rocks on the western margin of the Kon Tum Block (South Viet Nam). This unit has been identified as the Cu Brei Formation. Coral and stromatoporoid species have been described including Squameofavosites aff. spongiosus, Parallelostroma cf. multicolumnum, Amphipora cf. rasilis, A. cf. raritalis, Simplexodictyon cf. artyschtense, Stromatopora cf. boriarchinovi and Stromatopora sp. indet. The Cu Brei Formation is exposed in a small area 6 km in length and 3 km wide at the foot of Cu Brei Mountain (Sa Thay District, Kon Tum Province). As this formation is in marine shelf facies it is probable that further exposures of Lower Devonian sediments may be discovered in the Kon Tum Block. This discovery raises the question of the tectonic history of the metamorphic Kon Tum Block. It is possible that the block was not an area of positive uplift from the beginning of Paleozoic as has been supposed, but was submerged in a marine environment, at least on its outer margins, in the Devonian, and possibly even earlier, in Early Paleozoic.

Features of the first great shale gas field in China

Directory of Open Access Journals (Sweden)

Ruobing Liu

2016-04-01

Full Text Available On the 28th of November 2012, high shale gas flow was confirmed to be 203 × 103 m3 in Longmaxi Formation; this led to the discovery of the Fuling Shale Gas Field. On the 10th of July in 2014, the verified geological reserves of the first shale gas field in China were submitted to the National Reserves Committee. Practices of exploration and development proved that the reservoirs in the Fuling Shale Gas Field had quality shales deposited in the deep-shelf; the deep-shelf had stable distribution, great thickness with no interlayers. The shale gas field was characterized by high well production, high-pressure reservoirs, good gas elements, and satisfactory effects on testing production; it's from the mid-deep depth of the quality natural gas reservoirs that bore high pressure. Comprehensive studies on the regional sedimentary background, lithology, micropore structures, geophysical properties, gas sources, features of gas reservoirs, logging responding features, and producing features of gas wells showed the following: (1 The Longmaxi Formation in the Fuling Shale Gas Field belongs to deep-shelf environment where wells developed due to organic-rich shales. (2 Thermal evolution of shales in Longmaxi Formation was moderate, nanometer-level pores developed as well. (3 The shale gas sources came from kerogens the Longmaxi Formation itself. (4 The shale gas reservoirs of the Fuling Longmaxi Formation were similar to the typical geological features and producing rules in North America. The findings proved that the shale gas produced in the Longmaxi Formation in Fuling was the conventional in-situ detained, self-generated, and self-stored shale gas.

EVALUATION OF SHALE GAS POTENTIAL IN KAZAKHSTAN

Directory of Open Access Journals (Sweden)

Lidiya Parkhomchik

2015-01-01

Full Text Available The article considers the primary evaluation of the shale gas resource potential in Kazakhstan, as well as defines the most problematic issues for the large-scale shale gas production over the state. The authors pay special attention to the national strategy of the Kazakhstani government in the sphere of the unconventional energy sources production, defining the possible technological and environmental problems for the shale gas extraction. The article also notes that implementation of the fracking technologies in the country could cause both positive and negative effects on the economy of Kazakhstan. Therefore, further steps in this direction should be based on the meaningful and comprehensive geological data regarding the shale gas potential.

Root evolution at the base of the lycophyte clade: insights from an Early Devonian lycophyte

Science.gov (United States)

Matsunaga, Kelly K. S.; Tomescu, Alexandru M. F.

2016-01-01

Background and Aims The evolution of complex rooting systems during the Devonian had significant impacts on global terrestrial ecosystems and the evolution of plant body plans. However, detailed understanding of the pathways of root evolution and the architecture of early rooting systems is currently lacking. We describe the architecture and resolve the structural homology of the rooting system of an Early Devonian basal lycophyte. Insights gained from these fossils are used to address lycophyte root evolution and homology. Methods Plant fossils are preserved as carbonaceous compressions at Cottonwood Canyon (Wyoming), in the Lochkovian–Pragian (∼411 Ma; Early Devonian) Beartooth Butte Formation. We analysed 177 rock specimens and documented morphology, cuticular anatomy and structural relationships, as well as stratigraphic position and taphonomic conditions. Key Results The rooting system of the Cottonwood Canyon lycophyte is composed of modified stems that bear fine, dichotomously branching lateral roots. These modified stems, referred to as root-bearing axes, are produced at branching points of the above-ground shoot system. Root-bearing axes preserved in growth position exhibit evidence of positive gravitropism, whereas the lateral roots extend horizontally. Consistent recurrence of these features in successive populations of the plant preserved in situ demonstrates that they represent constitutive structural traits and not opportunistic responses of a flexible developmental programme. Conclusions This is the oldest direct evidence for a rooting system preserved in growth position. These rooting systems, which can be traced to a parent plant, include some of the earliest roots known to date and demonstrate that substantial plant–substrate interactions were under way by Early Devonian time. The morphological relationships between stems, root-bearing axes and roots corroborate evidence that positive gravitropism and root identity were evolutionarily

Laboratory weathering of combusted oil shale

International Nuclear Information System (INIS)

Essington, M.E.

1991-01-01

The objective of this study was to examine the mineralogy and leachate chemistry of three combusted oil shales (two Green River Formation and one New Albany) in a laboratory weathering environment using the humidity cell technique. The mineralogy of the combusted western oil shales (Green River Formation) is process dependent. In general, processing resulted in the formation of anhydrite, lime, periclase, and hematite. During the initial stages of weathering, lime, periclase, and hematite. During the initial stages of weathering, lime, periclase, and anhydrite dissolve and ettringite precipitates. The initial leachates are highly alkaline, saline, and dominated by Na, hydroxide, and SO 4 . As weathering continues, ettringite precipitates. The initial leachates are highly alkaline, saline, and dominated by Na, hydroxide, and SO 4 . As weathering continues, ettringite dissolves, gypsum and calcite precipitate, and the leachates are dominated by Mg, SO 4 , and CO 3 . Leachate pH is rapidly reduced to between 8.5 and 9 with leaching. The combusted eastern oil shale (New Albany) is composed of quartz, illite, hematite, and orthoclase. Weathering results in the precipitation of gypsum. The combusted eastern oil shale did not display a potential to produce acid drainage. Leachate chemistry was dominated by Ca and SO 4 . Element concentrations continually decreased with weathering. IN a western disposal environment receiving minimal atmospheric precipitation, spent oil shale will remain in the initial stages of weathering, and highly alkaline and saline conditions will dominate leachate chemistry. In an eastern disposal environment, soluble salts will be rapidly removed from the spent oil shale to potentially affect the surrounding environment

Geothermal alteration of clay minerals and shales: diagenesis

Energy Technology Data Exchange (ETDEWEB)

Weaver, C.E.

1979-07-01

The objective of this report is to perform a critical review of the data on the mineral and chemical alterations that occur during diagenesis and low-grade metamorphism of shale and other clay-rich rocks - conditions similar to those expected from emplacement of heat-producing radioactive waste in a geologic repository. The conclusions drawn in this document are that the following type of alterations could occur: smectite alteration, ion mobilization, illitic shales, kaolinite reactions, chlorite reactions, organic reactions, paleotemperatures, low temperature shales, high temperature shales, and phase equilibrium changes.

Geothermal alteration of clay minerals and shales: diagenesis

International Nuclear Information System (INIS)

Weaver, C.E.

1979-07-01

The objective of this report is to perform a critical review of the data on the mineral and chemical alterations that occur during diagenesis and low-grade metamorphism of shale and other clay-rich rocks - conditions similar to those expected from emplacement of heat-producing radioactive waste in a geologic repository. The conclusions drawn in this document are that the following type of alterations could occur: smectite alteration, ion mobilization, illitic shales, kaolinite reactions, chlorite reactions, organic reactions, paleotemperatures, low temperature shales, high temperature shales, and phase equilibrium changes

Sorption of cesium, strontium, and technetium onto organic-extracted shales

International Nuclear Information System (INIS)

Ho, P.C.

1992-01-01

The sorption of Cs(I), Sr(II), and Tc(VII) onto organic-extracted shales from synthetic brine groundwaters and from 0.03-M NaHCO 3 solution under oxid conditions at room temperature has been studied. The shale samples used in this study were Pumpkin Valley, Upper Dowelltown, Pierre and Green River Formation Shales. The organic content of these shales ranges from less than 2 wt% to 13 wt%. Soxhlet extraction with chloroform and a mixture of chloroform and methanol removed 0.07 to 5.9 wt% of the total organic matter from these shales. In comparison with the results of sorption of these three metal ions onto the corresponding untreated shales, it was observed that there were moderate to significant sorption decreases of Cs(I) and Sr(II) on all four organic-extracted shale samples and moderate sorption decrease of Tc(VII) on the organic-extracted Pumpkin Valley, Pierre, and Green River Shale samples, but only moderate sorption increases of Tc(VII) on the organic-extracted Upper Dowelltown Shale samples from the brine groundwaters. Nevertheless, sorption of Cs(I), Sr(II), and Tc(VII) on all four organic-extracted shale samples from the bicarbonate solution in most cases did not show a consistent pattern. (orig.)

Volatile characteristic of trace elements during microwave pyrolysis of oil shale

Energy Technology Data Exchange (ETDEWEB)

Bai, Jing-ru; Wang, Qing; Kong, Ling-wen; Bai, Zhang [Northeast Dianli Univ., Jilin (China). Engineering Research Centre

2013-07-01

Oil shale is abundant in the world. Today, the industry of oil shale retorting for producing shale oil is developing owing to high price of oil in the world. In order to study migratory behavior of trace elements in oil shale at microwave pyrolysis, tests were performed in laboratory with oil shale of the Huadian deposit of China at different powers from 400 to 700 W. The trace elements As, Cd, Hg, Mo, Pb, Se, Cr, Cu, Ni, V, Zn, Ba, Co, Mn present in oil shale and shale char were determined by the inductively coupled plasma-mass spectrometry (ICP-MS). By comparing the content of trace elements in oil shale and shale char, distribution characteristics of trace elements at retorting were studied. The overall trends of volatile ratio of trace elements are ascending with higher microwave power and higher than the conventional pyrolysis. The differences in the volatile ratio indicate that the trace elements investigated are bound with the oil shale kerogen and its mineral matter in different manner. So Float-sink experiments (FSE) were performed on oil shale. Huadian oil shale has more included mineral. The volatilization of organic matter is not the main reason for the volatilization of trace elements in oil shale. The trace elements combined with the mineral elements may be also certain volatility.

The real hazards of shale gas

International Nuclear Information System (INIS)

Favari, Daniele; Picot, Andre; Durand, Marc

2013-01-01

This bibliographical sheet presents a book which addresses the issue of shale gas. A first part describes the origin of this gaseous hydrocarbon, the composition of shale gas and its extraction, the technique of hydraulic fracturing, and the environmental risks. A second part addresses the economic, ecologic and political issues. The authors outline that all signs are there to prove the alarming hazards of shale gas. One of the authors outlines the necessity of an energy transition, far from fossil and nuclear energy, in order to guarantee a high level of protection of human health and of the environment

Analysis of oil shale and oil shale products for certain minor elements

International Nuclear Information System (INIS)

Dickman, P.T.; Purdy, M.; Doerges, J.E.; Ryan, V.A.; Poulson, R.E.

1977-01-01

The University of Wyoming was contracted by the Department of Energy's Laramie Energy Research Center (LERC) to develop rapid, inexpensive, and simple methods of quantitative and qualitative elemental analysis for products used and generated in the simulated in-situ retorting of oil shale. Alpha particle spectrometry was used to determine the radioisotope content of the aqueous retort products. Alpha particles are mono-energetic and the spectrometry method employed had very low background levels (1 count per 2000 seconds). These factors allow for both the quantitative and qualitative analysis of natural radioisotopes at the 1 ppm level. Sample preparation does not require any chemical treatment. Energy dispersive x-ray fluorescence (XRF) was used for the multi-element analysis of the retort products. The XRF, integrated with a mini-computer, allows rapid analysis of several elements in multiple samples. XRF samples require minimal amounts of preparation and analytical results are highly reproducible. This paper presents the methods developed and preliminary analytical results from oil shale by-products. Results from the analysis of oil shale rocks are not yet ready for presentation

Thermal evolution and shale gas potential estimation of the Wealden and Posidonia Shale in NW-Germany and the Netherlands : a 3D basin modelling study

NARCIS (Netherlands)

Bruns, B.; Littke, R.; Gasparik, M.; van Wees, J.-D.; Nelskamp, S.

Sedimentary basins in NW-Germany and the Netherlands represent potential targets for shale gas exploration in Europe due to the presence of Cretaceous (Wealden) and Jurassic (Posidonia) marlstones/shales as well as various Carboniferous black shales. In order to assess the regional shale gas

18 CFR 270.101 - General definitions.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF ENERGY PROCEDURES GOVERNING DETERMINATIONS FOR TAX CREDIT PURPOSES DETERMINATION PROCEDURES... gas produced from coal seams means naturally occurring natural gas released from entrapment from the fractures, pores and bedding planes of coal seams. (7) Natural gas produced from Devonian shale means...

) Geochemistry and Hydrocarbon Potential of Cretaceous Shales in the Chad Basin

International Nuclear Information System (INIS)

Alalade, B.; Ogunyemi, A. T.; Abimbola, A.F.; Olugbemiro, R. O.

2003-01-01

The Chad Basin is the largest intracratonic basin in Africa and is filled with more than 400m of Cretaceous to Recent sediments. Geochemical and petrographic studies of Cretaceous shales form the Bima, Gongola and Fika Formations were carried out to establish their hydrocarbon potential and thermal maturity. Ditch cuttings of the shales were collected from the Wa di and Karen's exploration wells located in the Nigerian sector of the Chad Basin.The geochemical analysis of the shales indicate that, except for Si02 and K20, all other oxides (Mg O, Fe2O3, AL2O3, CaO) are more abundant in the Fika shale than the Gongola shale. This suggests a more marine condition for the Fika shale compared to the Gongola shale. The Fika and Gongola shales were further classified into Iron shale and shale respectively. Organic carbon contents of the Bima, Gongola and exceed the minimum (0.5wt%) usually required for siliciclastic petroleum source rock. However, the soluble organic matter (SOM) and saturated hydrocarbon (SHC) contents of the shales, which ranges from 108pm to 743ppm and 23ppm to 100ppm respectively, are generally low and are therefore, organically lean. The organic matter of the shales is predominantly terrestrially derived, vitrinite rich, Type III kerogen and are therefore, gas prone. Thermal maturity assessed from SOM/TOC, SHC/TOC ratios and spore color index (SCI) indicate that the Fika shale is immature while the Gongola and Bima shales are within the oil window

Quantifying porosity, compressibility and permeability in Shale

DEFF Research Database (Denmark)

Mbia, Ernest Ncha; Fabricius, Ida Lykke; Frykman, Peter

strain data. We found that Kozeny's modelled permeability fall in the same order of magnitude with measured permeability for shale rich in kaolinite but overestimates permeability by two to three orders of magnitudes for shale with high content of smectite. The empirical Yang and Aplin model gives good...... permeability estimate comparable to the measured one for shale rich in smectite. This is probably because Yang and Aplin model was calibrated in London clay which is rich in smectite....

Extraction of hydrocarbon products from shales and coals

Energy Technology Data Exchange (ETDEWEB)

Reed, V Z

1918-05-17

A process is disclosed of extracting hydrocarbon oil matter from petroleum-bearing shales and coals which comprises subjecting a mass of such shale or coal, before distillation to the solvent action of material containing an acid, permitting the solvent material to pass through the mass of shale or coal, and recovering the combined solvent and extracted matter.

Energy Return on Investment (EROI of Oil Shale

Directory of Open Access Journals (Sweden)

Peter A. O’Connor

2011-11-01

Full Text Available The two methods of processing synthetic crude from organic marlstone in demonstration or small-scale commercial status in the U.S. are in situ extraction and surface retorting. The considerable uncertainty surrounding the technological characterization, resource characterization, and choice of the system boundary for oil shale operations indicate that oil shale is only a minor net energy producer if one includes internal energy (energy in the shale that is used during the process as an energy cost. The energy return on investment (EROI for either of these methods is roughly 1.5:1 for the final fuel product. The inclusions or omission of internal energy is a critical question. If only external energy (energy diverted from the economy to produce the fuel is considered, EROI appears to be much higher. In comparison, fuels produced from conventional petroleum show overall EROI of approximately 4.5:1. “At the wellhead” EROI is approximately 2:1 for shale oil (again, considering internal energy and 20:1 for petroleum. The low EROI for oil shale leads to a significant release of greenhouse gases. The large quantities of energy needed to process oil shale, combined with the thermochemistry of the retorting process, produce carbon dioxide and other greenhouse gas emissions. Oil shale unambiguously emits more greenhouse gases than conventional liquid fuels from crude oil feedstocks by a factor of 1.2 to 1.75. Much of the discussion regarding the EROI for oil shale should be regarded as preliminary or speculative due to the very small number of operating facilities that can be assessed.

Strontium isotopes test long-term zonal isolation of injected and Marcellus formation water after hydraulic fracturing.

Science.gov (United States)

Kohl, Courtney A Kolesar; Capo, Rosemary C; Stewart, Brian W; Wall, Andrew J; Schroeder, Karl T; Hammack, Richard W; Guthrie, George D

2014-08-19

One concern regarding unconventional hydrocarbon production from organic-rich shale is that hydraulic fracture stimulation could create pathways that allow injected fluids and deep brines from the target formation or adjacent units to migrate upward into shallow drinking water aquifers. This study presents Sr isotope and geochemical data from a well-constrained site in Greene County, Pennsylvania, in which samples were collected before and after hydraulic fracturing of the Middle Devonian Marcellus Shale. Results spanning a 15-month period indicated no significant migration of Marcellus-derived fluids into Upper Devonian/Lower Mississippian units located 900-1200 m above the lateral Marcellus boreholes or into groundwater sampled at a spring near the site. Monitoring the Sr isotope ratio of water from legacy oil and gas wells or drinking water wells can provide a sensitive early warning of upward brine migration for many years after well stimulation.

Updated methodology for nuclear magnetic resonance characterization of shales

Science.gov (United States)

Washburn, Kathryn E.; Birdwell, Justin E.

2013-08-01

Unconventional petroleum resources, particularly in shales, are expected to play an increasingly important role in the world's energy portfolio in the coming years. Nuclear magnetic resonance (NMR), particularly at low-field, provides important information in the evaluation of shale resources. Most of the low-field NMR analyses performed on shale samples rely heavily on standard T1 and T2 measurements. We present a new approach using solid echoes in the measurement of T1 and T1-T2 correlations that addresses some of the challenges encountered when making NMR measurements on shale samples compared to conventional reservoir rocks. Combining these techniques with standard T1 and T2 measurements provides a more complete assessment of the hydrogen-bearing constituents (e.g., bitumen, kerogen, clay-bound water) in shale samples. These methods are applied to immature and pyrolyzed oil shale samples to examine the solid and highly viscous organic phases present during the petroleum generation process. The solid echo measurements produce additional signal in the oil shale samples compared to the standard methodologies, indicating the presence of components undergoing homonuclear dipolar coupling. The results presented here include the first low-field NMR measurements performed on kerogen as well as detailed NMR analysis of highly viscous thermally generated bitumen present in pyrolyzed oil shale.

Prediction of shale prospectivity from seismically-derived reservoir and completion qualities: Application to a shale-gas field, Horn River Basin, Canada

Science.gov (United States)

Mo, Cheol Hoon; Lee, Gwang H.; Jeoung, Taek Ju; Ko, Kyung Nam; Kim, Ki Soo; Park, Kyung-sick; Shin, Chang Hoon

2018-04-01

Prospective shale plays require a combination of good reservoir and completion qualities. Total organic carbon (TOC) is an important reservoir quality and brittleness is the most critical condition for completion quality. We analyzed seismically-derived brittleness and TOC to investigate the prospectivity of the Horn River Group shale (the Muskwa, Otter Park, Evie shales) of a shale-gas field in the western Horn River Basin, British Columbia, Canada. We used the λρ-μρ brittleness template, constructed from the mineralogy-based brittleness index (MBI) and elastic logs from two wells, to convert the λρ and μρ volumes from prestack seismic inversion to the volume for the brittleness petrotypes (most brittle, intermediate, and least brittle). The probability maps of the most brittle petrotype for the three shales were generated from Bayesian classification, based on the λρ-μρ template. The relationship between TOC and P-wave and S-wave velocity ratio (VP/VS) at the wells allowed the conversion of the VP/VS volume from prestack inversion to the TOC volume, which in turn was used to construct the TOC maps for the three shales. Increased TOC is correlated with high brittleness, contrasting with the commonly-held understanding. Therefore, the prospectivity of the shales in the study area can be represented by high brittleness and increased TOC. We propose a shale prospectivity index (SPI), computed by the arithmetic average of the normalized probability of the most brittle petrotype and the normalized TOC. The higher SPI corresponds to higher production rates in the Muskwa and Evie shales. The areas of the highest SPI have not been fully tested. The future drilling should be focused on these areas to increase the economic viability of the field.

Process for treating oil shale

Energy Technology Data Exchange (ETDEWEB)

1920-08-22

A process for treating oil shale is characterized in that the shale is first finely ground, then heated in the presence of steam in a high-pressure retort at 1 to 50 atmospheres pressure at a temperature of 200/sup 0/ to 450/sup 0/C and then with large amounts of water with or without materials forming emulsions with water or with oil. Solution medium suitable for bitumen or paraffin is beaten up in a rapid hammer mill until all or most all of the oil or bitumen is emulsified. The emulsion is separated by filter-pressing and centrifuging from the solid shale residue and the oil or bitumen is again separated from the emulsion medium by heating, acidulating, standing, or centrifuging, and then in known ways is further separated, refined, and worked up.

Shale gas development impacts on surface water quality in Pennsylvania

Science.gov (United States)

Olmstead, Sheila M.; Muehlenbachs, Lucija A.; Shih, Jhih-Shyang; Chu, Ziyan; Krupnick, Alan J.

2013-01-01

Concern has been raised in the scientific literature about the environmental implications of extracting natural gas from deep shale formations, and published studies suggest that shale gas development may affect local groundwater quality. The potential for surface water quality degradation has been discussed in prior work, although no empirical analysis of this issue has been published. The potential for large-scale surface water quality degradation has affected regulatory approaches to shale gas development in some US states, despite the dearth of evidence. This paper conducts a large-scale examination of the extent to which shale gas development activities affect surface water quality. Focusing on the Marcellus Shale in Pennsylvania, we estimate the effect of shale gas wells and the release of treated shale gas waste by permitted treatment facilities on observed downstream concentrations of chloride (Cl−) and total suspended solids (TSS), controlling for other factors. Results suggest that (i) the treatment of shale gas waste by treatment plants in a watershed raises downstream Cl− concentrations but not TSS concentrations, and (ii) the presence of shale gas wells in a watershed raises downstream TSS concentrations but not Cl− concentrations. These results can inform future voluntary measures taken by shale gas operators and policy approaches taken by regulators to protect surface water quality as the scale of this economically important activity increases. PMID:23479604

Shale as a radioactive waste repository: the importance of vermiculite

Energy Technology Data Exchange (ETDEWEB)

Komarneni, S; Roy, D M; Pennsylvania State Univ., University Park; USA). Materials Research Labs.)

1979-01-01

Cesium sorption and fixation properties of thirty shale minerals and shales were investigated in search of a criterion for the suitability of shales for a radioactive waste repository. Shales and illites containing vermiculite fixed the largest proportion of total Cs sorbed (up to 91%) against displacement with 0.1 N KCl. For example, a slate sample fixed 33% of the total Cs sorbed while its weathered counterpart in which chlorite had altered to vermiculite fixed 89% of the total Cs sorbed. Since Cs is one of the most soluble and hazardous radioactive ions, its containment is of great importance in safe radioactive waste disposal. Presence of vermiculite in a shale body may therefore, serve as one criterion in the selection of a suitable shale for radioactive waste disposal if and when shales in geologically stable areas are selected for repositories.

Method and arrangement of distillation of shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1920-03-29

A method is given of distilling shale and other bituminous materials utilizing the heat from the combustion of the residue, possibly with additional heat from other fuels. It is characterized by the shale, which is arranged in layers, being first submitted to a process of distillation utilizing the heat mentioned, and at the same time recovering the products of distillation, and second the shale being burned without disturbing the layers to any appreciable extent. The patent has 16 more claims.

Chemistry of the Estonian oil-shale kukersite

Energy Technology Data Exchange (ETDEWEB)

Kogerman, P N

1931-01-01

Estonian oil shale is one of the oldest and richest oil shales in the world. The deposits occur in the Middle-Ordovician strata having a total thickness of 2.2 meters. The ultimate composition of the kerogen varied within the following limits: carbon 76.5 to 76.7 percent, hydrogen 9.1 to 9.2 percent, nitrogen 0.2 to 0.4 percent, sulfur 1.6 to 2.2 percent, chlorine 0.5 to 0.7 percent, and oxygen (by difference) 11.2 to 12.2 percent. The composition of kukersite kerogen corresponds nearly to the empirical formula (C/sub 8/H/sub 11/O)n. One of the most significant differences between kukersite, coal, and lignite is the amount of alkali-soluble substances present. Kukersite has almost no humic acids. Samples of kukersite were brominated and chlorinated. The halogenated shales showed a solubility in absolute alcohol of 26 percent compared to only 0.31 percent for untreated shale. Enriched shale (4.5 percent ash) did not react with chlorine as much as did raw shale. Apparently the mineral matter acted catalytically during chlorination. The amount of soluble extract obtained by solvent treatment of kukersite ranged from 0.22 percent with chloroform to 2.20 percent with tetrachloroethane. Heat was the most effective agent for the depolymerization of kukersite kerogen. The percentage loss of weight due to drying in air was much less than in the presence of carbon dioxide. The results indicated that on drying in air, the powdered shale loses water and a volatile substance, probably the oxides of carbon, up to 80/sup 0/C. Carbon dioxide was also found to be present in the gases eliminated at the temperature of initial decomposition. Pulverized shale, heated for 6 hours at 220/sup 0/C, lost 2.6 percent of its weight; its solubility in carbon disulfide was 2.11 percent. Kukersite kerogen was formed from compounds that were resistent to bacteriological decomposition, such as waxes and resins, plus decomposition products of proteins, cellulose, and putrefaction products of

Geology of Paleozoic Rocks in the Upper Colorado River Basin in Arizona, Colorado, New Mexico, Utah, and Wyoming, Excluding the San Juan Basin

Science.gov (United States)

Geldon, Arthur L.

2003-01-01

The geology of the Paleozoic rocks in the Upper Colorado River Basin in Arizona, Colorado, New Mexico, Utah, and Wyoming, was studied as part of the U.S. Geological Survey's Regional Aquifer-System Analysis Program to provide support for hydrogeological interpretations. The study area is segmented by numerous uplifts and basins caused by folding and faulting that have recurred repeatedly from Precambrian to Cenozoic time. Paleozoic rocks in the study area are 0-18,000 feet thick. They are underlain by Precambrian igneous, metamorphic, and sedimentary rocks and are overlain in most of the area by Triassic formations composed mostly of shale. The overlying Mesozoic and Tertiary rocks are 0-27,000 feet thick. All Paleozoic systems except the Silurian are represented in the region. The Paleozoic rocks are divisible into 11 hydrogeologic units. The basal hydrogeologic unit consisting of Paleozoic rocks, the Flathead aquifer, predominantly is composed of Lower to Upper Cambrian sandstone and quartzite. The aquifer is 0-800 feet thick and is overlain gradationally to unconformably by formations of Cambrian to Mississippian age. The Gros Ventre confining unit consists of Middle to Upper Cambrian shale with subordinate carbonate rocks and sandstone. The confining unit is 0-1,100 feet thick and is overlain gradationally to unconformably by formations of Cambrian to Mississippian age. The Bighom aquifer consists of Middle Cambrian to Upper Ordovician limestone and dolomite with subordinate shale and sandstone. The aquifer is 0-3,000 feet thick and is overlain unconformably by Devonian and Mississipplan rocks. The Elbert-Parting confining unit consists of Lower Devonian to Lower Mississippian limestone, dolomite, sandstone, quartzite, shale, and anhydrite. It is 0-700 feet thick and is overlain conformably to unconformably by Upper Devonian and Mississippian rocks. The Madison aquifer consists of two zones of distinctly different lithology. The lower (Redwall-Leadville) zone

U-Pb dating of silicic lavas, sills and syneruptive resedimented volcaniclastic deposits of the Lower Devonian Crudine Group, Hill End Trough, New South Wales

International Nuclear Information System (INIS)

Jagodzinski, E.A.; Black, L.P.

1999-01-01

The Hill End Trough of central-western New South Wales was an elongate deep marine basin that existed in the Lachlan Fold Belt from the early Late Silurian to late Early Devonian. It is represented by a regionally extensive. unfossiliferous sequence of interbedded turbidites and hemipelagites of substantially silicic Volcanic derivation, which passes laterally into contemporaneous shallow-water sedimentary rocks. The Turondale and Merrions Formations of the Lower Devonian Crudine Group are two prominent volcanogenic formations in the predominantly sedimentary trough sequence. They contain a range of primary and resedimented volcanic facies suitable for U-Pb dating. These include widespread subaqueous silicic lavas and/or lava cryptodomes. and thick sequences of crystal-rich volcaniclastic sandstone emplaced by a succession of muss-flows that were generated by interaction between contemporaneous subaerial pyroclastic flows and the sea. Ion microprobe dating of the two volcanogenic formations by means of the commonly used SL 13 zircon standard yields ages ranging between 411.3 ± 5.1 and 404.8 ± 4.8 Ma. Normalising the data against a different zircon standard (QGNG) yields preferred slightly older mean ages that range between 413.4 ± 6.6 and 407.1 ± 6.9 Ma. These ages broadly approximate the Early Devonian age that has been historically associated with the Crudine Group. However, the biostratigraphically inferred late Lochkovian - early Emsian (mid-Early Devonian) age for the Merrions Formation is inconsistent with the current Australian Phunerozoic Timescale, which assigns an age of 410 Ma to the Silurian-Devonian boundary, and ages of 404.5 Ma and 395.5 Ma to the base and top of the Pragian, respectively. There is, however, good agreement if the new ages are compared with the most recently published revision of the Devonian time-scale. This suggests that the Early Devonian stage boundaries of the Australian Phanerozoic Timescale need to be revised downward. The

Evolution of the Southern Margin of the Donbas (Ukraine) from Devonian to early Carboniferous Times.

NARCIS (Netherlands)

McCann, T.; Saintot, A.N.

2003-01-01

A Devonian-Early Carboniferous succession comprising thick clastic and carbonate sediments with interbedded volcanics was examined along the southern margin of the Donbas fold belt. Ukraine. Following initial rifting and subsidence, a continental (fluvial, lacustrine) succession was established.

Scale up risk of developing oil shale processing units

International Nuclear Information System (INIS)

Oepik, I.

1991-01-01

The experiences in oil shale processing in three large countries, China, the U.S.A. and the U.S.S.R. have demonstrated, that the relative scale up risk of developing oil shale processing units is related to the scale up factor. On the background of large programmes for developing the oil shale industry branch, i.e. the $30 billion investments in colorado and Utah or 50 million t/year oil shale processing in Estonia and Leningrad Region planned in the late seventies, the absolute scope of the scale up risk of developing single retorting plants, seems to be justified. But under the conditions of low crude oil prices, when the large-scale development of oil shale processing industry is stopped, the absolute scope of the scale up risk is to be divided between a small number of units. Therefore, it is reasonable to build the new commercial oil shale processing plants with a minimum scale up risk. For example, in Estonia a new oil shale processing plant with gas combustion retorts projected to start in the early nineties will be equipped with four units of 1500 t/day enriched oil shale throughput each, designed with scale up factor M=1.5 and with a minimum scale up risk, only r=2.5-4.5%. The oil shale retorting unit for the PAMA plant in Israel [1] is planned to develop in three steps, also with minimum scale up risk: feasibility studies in Colorado with Israel's shale at Paraho 250 t/day retort and other tests, demonstration retort of 700 t/day and M=2.8 in Israel, and commercial retorts in the early nineties with the capacity of about 1000 t/day with M=1.4. The scale up risk of the PAMA project r=2-4% is approximately the same as that in Estonia. the knowledge of the scope of the scale up risk of developing oil shale processing retorts assists on the calculation of production costs in erecting new units. (author). 9 refs., 2 tabs

Shale gas characterization based on geochemical and geophysical analysis: Case study of Brown shale, Pematang formation, Central Sumatra Basin

Science.gov (United States)

Haris, A.; Nastria, N.; Soebandrio, D.; Riyanto, A.

2017-07-01

Geochemical and geophysical analyses of shale gas have been carried out in Brown Shale, Middle Pematang Formation, Central Sumatra Basin. The paper is aimed at delineating the sweet spot distribution of potential shale gas reservoir, which is based on Total Organic Carbon (TOC), Maturity level data, and combined with TOC modeling that refers to Passey and Regression Multi Linear method. We used 4 well data, side wall core and 3D pre-stack seismic data. Our analysis of geochemical properties is based on well log and core data and its distribution are constrained by a framework of 3D seismic data, which is transformed into acoustic impedance. Further, the sweet spot of organic-rich shale is delineated by mapping TOC, which is extracted from inverted acoustic impedance. Our experiment analysis shows that organic materials contained in the formation of Middle Pematang Brown Shale members have TOC range from 0.15 to 2.71 wt.%, which is classified in the quality of poor to very good. In addition, the maturity level of organic material is ranging from 373°C to 432°C, which is indicated by vitrinite reflectance (Ro) of 0.58. In term of kerogen type, this Brown shale formation is categorized as kerogen type of II I III, which has the potential to generate a mixture of gasIoil on the environment.

Exploring support for shale gas extraction in the United Kingdom

International Nuclear Information System (INIS)

Andersson-Hudson, Jessica; Knight, William; Humphrey, Mathew; O’Hara, Sarah

2016-01-01

The development of shale gas in the United Kingdom (UK) using hydraulic fracturing, more commonly known as ‘fracking’, remains in its infancy. Yet understanding public attitudes for this fledgling industry is important for future policy considerations, decision-making and for industry stakeholders. This study uses data collected from the University of Nottingham, UK nationwide online survey (n=3823) conducted in September 2014, to consider ten hypothesises about the UK public's attitudes towards shale gas. From the survey data we can see that 43.11% of respondents support shale gas extraction in the UK. Furthermore, our results show that women, class DE respondents, non-Conservative party supporters, and respondents who positively associate shale gas with water contamination or earthquakes are less likely to support the extraction of shale gas in the UK. We also discuss potential policy implications for the UK government arising from these findings. - Highlights: • September 2014 survey of British attitudes towards allowing shale gas extraction. • Over 75% or respondents correctly identify shale gas. • 43.11% of respondents support shale gas extraction in the UK.

Late Devonian glacial deposits from the eastern United States signal an end of the mid-Paleozoic warm period

Science.gov (United States)

Brezinski, D.K.; Cecil, C.B.; Skema, V.W.; Stamm, R.

2008-01-01

A Late Devonian polymictic diamictite extends for more than 400??km from northeastern Pennsylvania across western Maryland and into east-central West Virginia. The matrix-supported, unbedded, locally sheared diamictite contains subangular to rounded clasts up to 2??m in diameter. The mostly rounded clasts are both locally derived and exotic; some exhibit striations, faceting, and polish. The diamictite commonly is overlain by laminated siltstone/mudstone facies associations (laminites). The laminites contain isolated clasts ranging in size from sand and pebbles to boulders, some of which are striated. The diamictite/laminite sequence is capped by massive, coarse-grained, pebbly sandstone that is trough cross-bedded. A stratigraphic change from red, calcic paleo-Vertisols in strata below the diamictite to non-calcic paleo-Spodosols and coal beds at and above the diamictite interval suggests that the climate became much wetter during deposition of the diamictite. The diamictite deposit is contemporaneous with regressive facies that reflect fluvial incision during the Late Devonian of the Appalachian basin. These deposits record a Late Devonian episode of climatic cooling so extreme that it produced glaciation in the Appalachian basin. Evidence for this episode of climatic cooling is preserved as the interpreted glacial deposits of diamictite, overlain by glaciolacustrine varves containing dropstones, and capped by sandstone interpreted as braided stream outwash. The Appalachian glacigenic deposits are contemporaneous with glacial deposits in South America, and suggest that Late Devonian climatic cooling was global. This period of dramatic global cooling may represent the end of the mid-Paleozoic warm interval that began in the Middle Silurian. ?? 2008 Elsevier B.V. All rights reserved.

Suggestions on the development strategy of shale gas in China

Directory of Open Access Journals (Sweden)

Dazhong Dong

2016-12-01

Full Text Available From the aspects of shale gas resource condition, main exploration and development progress, important breakthrough in key technologies and equipment, this paper systematically summarized and analyzed current situation of shale gas development in China and pointed out five big challenges such as misunderstandings, lower implementation degree and higher economic uncertainty of shale gas resource, and still no breakthrough in exploration and development core technologies and equipment for shale gas buried depth more than 3500 m, higher cost and other non-technical factors that restrict the development pace. Aiming at the above challenges, we put forward five suggestions to promote the shale gas development in China: (1 Make strategies and set goals according to our national conditions and exploration and development stages. That is, make sure to realize shale gas annual production of 20 × 109 m3, and strives to reach 30 × 109 m3. (2 Attach importance to the research of accumulation and enrichment geological theory and exploration & development key engineering technologies for lower production and lower pressure marine shale gas reservoir, and at the same time orderly promote the construction of non-marine shale gas exploration & development demonstration areas. (3 The government should introduce further policies and set special innovation funds to support the companies to carry out research and development of related technologies and equipment, especially to strengthen the research and development of technology, equipment and process for shale gas bellow 3500 m in order to achieve breakthrough in deep shale gas. (4 Continue to promote the geological theory, innovation in technology and management, and strengthen cost control on drilling, fracturing and the whole process in order to realize efficient, economic and scale development of China's shale gas. (5 Reform the mining rights management system, establish information platform of shale

Life cycle environmental impacts of UK shale gas

International Nuclear Information System (INIS)

Stamford, Laurence; Azapagic, Adisa

2014-01-01

Highlights: • First full life cycle assessment of shale gas used for electricity generation. • Comparison with coal, conventional and liquefied gas, nuclear, wind and solar PV. • Shale gas worse than coal for three impacts and better than renewables for four. • It has higher photochemical smog and terrestrial toxicity than the other options. • Shale gas a sound environmental option only if accompanied by stringent regulation. - Abstract: Exploitation of shale gas in the UK is at a very early stage, but with the latest estimates suggesting potential resources of 3.8 × 10 13 cubic metres – enough to supply the UK for next 470 years – it is viewed by many as an exciting economic prospect. However, its environmental impacts are currently unknown. This is the focus of this paper which estimates for the first time the life cycle impacts of UK shale gas, assuming its use for electricity generation. Shale gas is compared to fossil-fuel alternatives (conventional gas and coal) and low-carbon options (nuclear, offshore wind and solar photovoltaics). The results suggest that the impacts range widely, depending on the assumptions. For example, the global warming potential (GWP100) of electricity from shale gas ranges from 412 to 1102 g CO 2 -eq./kWh with a central estimate of 462 g. The central estimates suggest that shale gas is comparable or superior to conventional gas and low-carbon technologies for depletion of abiotic resources, eutrophication, and freshwater, marine and human toxicities. Conversely, it has a higher potential for creation of photochemical oxidants (smog) and terrestrial toxicity than any other option considered. For acidification, shale gas is a better option than coal power but an order of magnitude worse than the other options. The impact on ozone layer depletion is within the range found for conventional gas, but nuclear and wind power are better options still. The results of this research highlight the need for tight regulation and

Shale gas: how to progress. Report July 2014

International Nuclear Information System (INIS)

Clamadieu, Jean-Pierre; Aubagnac, Louis-Paul; Dolle, Julie; Lahet, Jean-Francois; Goffe, Bruno; Le Bihan-Graf, Christine; Rosenblieh, Laure; Puyfaucher, Laetitia

2014-07-01

This report proposes a multidisciplinary contribution to the debate on shale gas. It first shows that shale gas is already a reality at the international level, that the American economy has improved its competitiveness with direct consequences for the European economy, and notices that some countries which have been reluctant until now, are now evolving. The second part describes the potential of shale gas in France as important but with still uncertain resources. The authors outline that a status-quo would be a threat for the French industry on the short term. Then, the report proposes answers to some questions raised by the exploitation of shale gas in France in terms of risks related to hydraulic fracturing, to water resources, to methane emissions, to organic volatile compounds present in drilling waters, or in terms of noise and visual pollutions. In its last part, the report discusses how to progress in the assessment of the role of shale gas in the French and European energy mix, in the knowledge of the French underground, in the development of shale gas at the service of competitiveness, and with an ensured progressive and controlled evolution

An exploratory study of air emissions associated with shale gas development and production in the Barnett Shale.

Science.gov (United States)

Rich, Alisa; Grover, James P; Sattler, Melanie L

2014-01-01

Information regarding air emissions from shale gas extraction and production is critically important given production is occurring in highly urbanized areas across the United States. Objectives of this exploratory study were to collect ambient air samples in residential areas within 61 m (200 feet) of shale gas extraction/production and determine whether a "fingerprint" of chemicals can be associated with shale gas activity. Statistical analyses correlating fingerprint chemicals with methane, equipment, and processes of extraction/production were performed. Ambient air sampling in residential areas of shale gas extraction and production was conducted at six counties in the Dallas/Fort Worth (DFW) Metroplex from 2008 to 2010. The 39 locations tested were identified by clients that requested monitoring. Seven sites were sampled on 2 days (typically months later in another season), and two sites were sampled on 3 days, resulting in 50 sets of monitoring data. Twenty-four-hour passive samples were collected using summa canisters. Gas chromatography/mass spectrometer analysis was used to identify organic compounds present. Methane was present in concentrations above laboratory detection limits in 49 out of 50 sampling data sets. Most of the areas investigated had atmospheric methane concentrations considerably higher than reported urban background concentrations (1.8-2.0 ppm(v)). Other chemical constituents were found to be correlated with presence of methane. A principal components analysis (PCA) identified multivariate patterns of concentrations that potentially constitute signatures of emissions from different phases of operation at natural gas sites. The first factor identified through the PCA proved most informative. Extreme negative values were strongly and statistically associated with the presence of compressors at sample sites. The seven chemicals strongly associated with this factor (o-xylene, ethylbenzene, 1,2,4-trimethylbenzene, m- and p-xylene, 1

Employment Creation of Shale Gas Investment in China

Science.gov (United States)

Wang, Xuecheng; Zhang, Baosheng; Wu, Meiling; Li, Xiang; Lin, Yuying

2018-01-01

An ambitious shale gas extraction plan has been proposed. The huge investment of shale gas may put an effect on the whole China’s economy, especially for employment. However, there is few study to date has quantified these effects. The aim of this paper is to quantify these effects especially employment creation and figures out whether shale gas investment in China is a good choice or not. Input-output analysis has been utilized in this study to estimate the employment creation in four different Chinese regions. Our findings show that shale gas investment will result in creating 660000, 370000, 140000 and 58000 equivalent jobs in Sichuan, Chongqing, Inner Mongolia and Guizhou, respectively. Considering the potential risks of environmental issues, we suggest that it may be a better strategy for the government, at least in the current situation, to slow down shale gas development investment.

Effect of fluid–solid coupling on shale mechanics and seepage laws

Directory of Open Access Journals (Sweden)

Fuquan Song

2018-02-01

Full Text Available In this paper, the cores of outcropped black shale of Lower Silurian Longmaxi Fm in the Yibin area, Sichuan Basin, were taken as samples to investigate the effects of extraneous water on shale mechanics and seepage laws during the production of shale gas reservoirs. Firstly, the development of fractures in water saturated cores was observed by using a VHX-5000 optical superdepth microscope. Secondly, water, formation water and slick water, as well as the damage form and compression strength of water saturated/unsaturated cores were investigated by means of a uniaxial compression testing machine and a strain testing & analysis system. Finally, the effects of fluid–solid coupling on shale gas flowing performance in different water saturations were analyzed by using a DYQ-1 multi-function displacement device. Analysis on core components shows that the Longmaxi shale is a highly crushable reservoir with a high content of fragile minerals, so fracturing stimulation is suitable for it. Shale compression strength test reveals that the effects of deionized water, formation water and slick water on shale are different, so the compression strength of shale before being saturated is quite different from that after being saturated. Due to the existence of water, the compression strength of shale drops, so the shale can be fractured easily, more fractures are generated and thus its seepage capacity is improved. Experiments on shale gas seepage under different water saturations show that under the condition of fluid–solid coupling, the higher the water saturation is, the better the propagation and seepage capacity of micro-fractures in shale under the effect of pressure. To sum up, the existence of water is beneficial to fracturing stimulation of shale gas reservoirs and helps to achieve the goal of production improvement. Keywords: Shale gas, Core, Fluid–solid coupling, Water, Compression strength, Permeability, Seepage characteristic, Sichuan Basin

The Upper Devonian deposits in the northern part of Leon (Cantabrian Mountains, Northwestern Spain)

NARCIS (Netherlands)

Loevezijn, van G.B.S.; Raven, J.G.M.

1983-01-01

During the Late Devonian, deposition in the Cantabrian Mountains was largely controlled by movements along faults. By way of intermitting subsidence of the area south of the Sabero-Gordón line and the connected progradation of the coast during the Frasnian and early Famennian, three regressive

Oil. The revenge of shales

International Nuclear Information System (INIS)

Dupin, Ludovic

2017-01-01

This article comments the evolutions noticed during these past years as the USA started to exploit non conventional hydrocarbons (shale gas and oil), and thus reduced their supplies from the Middle East. In reaction, OPEC members provoked a massive oil price decrease. If shale oil exploitation in the USA has slowed down for a while, it starts again: the number of platforms and production are increasing. Moreover, the profitability threshold is strongly decreasing. Argentina and China are also developing this sector, and Great-Britain and South-Africa are about to start projects. The article outlines that, even though France decided not to exploit shale gas and oil, French industries are present on this market and technology. In an interview, a representative of the French sector of non conventional hydrocarbons comments these evolutions as well as the French decision and its possible evolutions

Late Devonian spermatophyte diversity and paleoecology at Red Hill, north-central Pennsylvania, USA

Energy Technology Data Exchange (ETDEWEB)

Cressler, Walter L. III. [Francis Harvey Green Library, 29 West Rosedale Avenue, West Chester University, West Chester, PA, 19383 (United States); Prestianni, Cyrille [Universite de Liege, Boulevard du Rectorat B18, Liege 4000 (Belgium); LePage, Ben A. [The Academy of Natural Sciences, 1900 Benjamin Franklin Parkway, Philadelphia, PA, 19103 and PECO Energy Company, 2301 Market Avenue, S9-1, Philadelphia, PA 19103 (United States)

2010-08-01

Early spermatophytes have been discovered at Red Hill, a Late Devonian (Famennian) fossil locality in north-central Pennsylvania, USA. The Red Hill locality contains an Archaeopteris-dominated flora within an outcrop of the Duncannon Member of the Catskill Formation. Palynological analyses of the plant fossil-bearing horizons within the Red Hill outcrop indicate deposition within the VCo palynozone. This is the earliest time horizon known to contain evidence for spermatophytes, and is contemporaneous with well-known spermatophyte-bearing deposits in West Virginia and Belgium. Some of the spermatophyte material from Red Hill compares well with Aglosperma sp., previously known as isolated ovules from the latest Devonian of South Wales and England, thus extending its geographic and stratigraphic range. Red Hill specimens of Aglosperma sp. occur both as isolated ovules and attached to dichotomously forking axes. Additional spermatophyte cupules discovered at Red Hill are morphologically similar to those of the previously described Late Devonian spermatophytes Elkinsia Rothwell, Scheckler, et Gillespie, Moresnetia Stockmans, and Xenotheca Arber et Goode. Some of the Red Hill cupule complexes are distinct from the aforementioned taxa in consisting of slender dichotomously forking axes terminating in paired cupules with highly fused and symmetric cupule quadrant lobes. The distinctive nature of these Red Hill specimens warrants the creation of Duodimidia pfefferkornii Cressler, Prestianni, et LePage gen. et sp. nov. Plant fossil remains with sphenopteroid foliage are also present at Red Hill, possibly attributable to the spermatophytes. Previous systematic sampling of the rich plant-fossil bearing layer at Red Hill and analysis of its floristic diversity and abundance as well as the presence and absence of charcoal suggests a pattern of floral turnover from a local-scale Rhacophyton-dominated community to spermatophyte colonization following disturbance by wildfires

Method of recovering oil from alum shales. [heating by electric currents

Energy Technology Data Exchange (ETDEWEB)

Wennerstrom, K G

1918-06-04

A method of treating alum shale and other bituminous shales in order to extract oil et cetera, is characterized by bringing the shale to a temperature at which it melts, and at which the necessary amount of heat is transferred to the molten shale to be distilled. The patent claim is characterized by heating the shale by means of electric current. The patent has one additional claim.

Gasification of oil shale by solar energy

International Nuclear Information System (INIS)

Ingel, Gil

1992-04-01

Gasification of oil shales followed by catalytic reforming can yield synthetic gas, which is easily transportable and may be used as a heat source or for producing liquid fuels. The aim of the present work was to study the gasification of oil shales by solar radiation, as a mean of combining these two energy resources. Such a combination results in maximizing the extractable fuel from the shale, as well as enabling us to store solar energy in a chemical bond. In this research special attention was focused upon the question of the possible enhancement of the gasification by direct solar irradiation of the solid carbonaceous feed stock. The oil shale served here as a model feedstock foe other resources such as coal, heavy fuels or biomass all of which can be gasified in the same manner. The experiments were performed at the Weizman institute's solar central receiver, using solar concentrated flux as an energy source for the gasification. The original contributions of this work are : 1) Experimental evidence is presented that concentrated sunlight can be used effectively to carry out highly endothermic chemical reactions in solid particles, which in turn forms an essential element in the open-loop solar chemical heat pipe; 2) The solar-driven gasification of oil shales can be executed with good conversion efficiencies, as well as high synthesis gas yields; 3)There was found substantial increase in deliverable energy compared to the conventional retorting of oil shales, and considerable reduction in the resulting spent shale. 5) A detailed computer model that incorporates all the principal optical and thermal components of the solar concentrator and the chemical reactor has been developed and compared favorably against experimental data. (author)

Wet separation processes as method to separate limestone and oil shale

Science.gov (United States)

Nurme, Martin; Karu, Veiko

2015-04-01

Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

Shale gas - los yacimientos de hidrocarburos no convencionales: origen del Shale gas

Directory of Open Access Journals (Sweden)

José Francisco Longoria Treviño

2015-06-01

Full Text Available El shale gas tiene su origen en la acumulación de materia orgánica en cuencas marinas. En Norteamérica el gas de lutita (shale gas es una fuente emergente de gas natural de bajo costo. El gas natural es una fuente de energía abundante y relativamente limpia al quemarse. Se ha convertido en un combustible popular tanto para aplicaciones residenciales como industriales. De acuerdo con los datos recientes se estima que el suministro de gas natural derivado de yacimientos no convencionales (gas de lutita – shale gas durará más de 100 años. El gas natural ofrece un remplazo potencial para sustituir a los combustibles fósiles que producen gases de efecto invernadero y que en la actualidad se usan en la generación de energía, calefacción y transporte. Las emisiones de gas de efecto invernadero de la combustión de gas natural son aproximadamente 30% más limpias que aquellas que se derivan del aceite y 45% más limpias de las del carbón.

Mathematical modelling of anisotropy of illite-rich shale

Science.gov (United States)

Chesnokov, E.M.; Tiwary, D.K.; Bayuk, I.O.; Sparkman, M.A.; Brown, R.L.

2009-01-01

The estimation of illite-rich shale anisotropy to account for the alignment of clays and gas- or brine-filled cracks is presented via mathematical modelling. Such estimation requires analysis to interpret the dominance of one effect over another. This knowledge can help to evaluate the permeability in the unconventional reservoir, stress orientation, and the seal capacity for the conventional reservoir. Effective media modelling is used to predict the elastic properties of the illite-rich shale and to identify the dominant contributions to the shale anisotropy. We consider two principal reasons of the shale anisotropy: orientation of clay platelets and orientation of fluid-filled cracks. In reality, both of these two factors affect the shale anisotropy. The goal of this study is, first, to separately analyse the effect of these two factors to reveal the specific features in P- and S-wave velocity behaviour typical of each of the factors, and, then, consider a combined effect of the factors when the cracks are horizontally or vertically aligned. To do this, we construct four models of shale. The behaviour of P- and S-wave velocities is analysed when gas- and water-filled cracks embedded in a host matrix are randomly oriented, or horizontally or vertically aligned. The host matrix can be either isotropic or anisotropic (of VTI symmetry). In such a modelling, we use published data on mineralogy and clay platelet alignment along with other micromechanical measurements. In the model, where the host matrix is isotropic, the presence of a singularity point (when the difference VS1 - VS2 changes its sign) in shear wave velocities is an indicator of brine-filled aligned cracks. In the model with the VTI host matrix and horizontally aligned cracks filled with gas, an increase in their volume concentration leads to that the azimuth at which the singularity is observed moves toward the symmetry axis. In this case, if the clay content is small (around 20 per cent), the

Shale gas, a French speciality - These French who are successful in shale gas; In Texas, Total is running full gas throttle

International Nuclear Information System (INIS)

Cognasse, Olivier; Dupin, Ludovic; Chandes, Camille

2013-01-01

A first article illustrates the strong presence of French companies in the shale gas sector, from the exploitation to gas liquefaction. Some examples are evoked: Total (gas fields and petrochemical), CGG (seismic exploration), Vallourec (tube manufacturer), Nexans (cable manufacturer), Imery and Saint-Gobain (ceramic balls used to maintain cracks opened), Saltel (fracturing), SNF Floerger (extraction), GDF Suez (shale gas export). The interest of some foreign actors in the French shale gas is also evoked. A second article reports the activity of Total in Port Arthur, Texas, where it adapted a huge steam cracker to shale gas. This illustrates the renewal of the American petrochemical industry

Total and the Algerian shale gas

International Nuclear Information System (INIS)

Chapelle, Sophie; Petitjean, Olivier; Maurin, Wilfried; Balvet, Jacqueline; Combes, Maxime; Geze, Francois; Hamouchene, Hamza; Hidouci, Ghazi; Malti, Hocine; Renaud, Juliette; Simon, Antoine; Titouche, Fateh

2015-01-01

This publication proposes a rather detailed and discussed overview of the movement of mobilisation of Algerian people (notably those living in the Sahara) against projects of exploration and exploitation of shale gases in Algeria by the Total group. The authors also recall and comment the long and heavy history of hydrocarbon management in Algeria, the role of international firms and of western interests (notably French interests) in this country, and the position of Total regarding the stake related to shale gases. The authors outline problems created by shale gas exploitation regarding water consumption and waste waters. They also notice that the safety of wells is at the centre of the protest. Problems raised by hydraulic fracturing are reviewed: seismic activity, chemical pollution, air pollution and greenhouse gases, landscape destruction. The attitude of the Algerian government is commented. Then, the authors try to identify and describe the action of Total in the Algerian shale gas sector, discuss the possible French influence, and outline the presence of Total all over the world in this sector

Oil shales of the Lothians. Part III. Chemistry of the oil shales

Energy Technology Data Exchange (ETDEWEB)

Steuart, D R

1912-01-01

Tests were performed whereby fuller's earth and lycopodium spore dust were heated to retorting temperatures and the crude oil examined. Oil shale may be composed of the following: vegetable matter that has been macerated and preserved by combining with salts, spores, and other such material that has been protected from decay, and a proportion of animal matter. Generally, oil shale may be considered as a torbanite that contains a large proportion of inorganic matter, or it may be a torbanite that has deteriorated with age. This supposition is based on the fact that oil yield decreases and the yield of ammonia increases with age.

Rapid gas development in the Fayetteville shale basin, Arkansas

Science.gov (United States)

Advances in drilling and extraction of natural gas have resulted in rapid expansion of wells in shale basins. The rate of gas well installation in the Fayetteville shale is 774 wells a year since 2005 with thousands more planned. The Fayetteville shale covers 23,000 km2 although ...

Shale Gas characteristics of Permian black shales (Ecca group, Eastern Cape, South Africa)

Science.gov (United States)

Geel, Claire; Booth, Peter; Schulz, Hans-Martin; Horsfield, Brian; de Wit, Maarten

2013-04-01

This study involves a comprehensive and detailed lithological, sedimentalogical, structural and geochemical description of the lower Ecca Group in the Eastern Cape, South Africa. The Ecca group hosts a ~ 245 million year old organic-rich black shale, which has recently been the focus of interest of petroleum companies worldwide. The shale was deposited under anoxic conditions in a setting which formed as a consequence of retro-arc foreland basin development related to the Cape Fold Belt. This sedimentary/tectonic environment provided the conditions for deeply buried black shales to reach maturity levels for development in the gas window. The investigation site is called the Greystone Area and is situated north of Wolwefontein en route to Jansenville. The area has outcrops of the Dwyka, the Ecca and the lower Beaufort Groups. The outcrops were mapped extensively and the data was used in conjunction with GIS software to produce a detailed geological map. North-south cross sections were drawn to give indication of bed thicknesses and formation depths. Using the field work, data two boreholes were accurately sited on the northern limb of a shallow easterly plunging syncline. The first borehole reached 100m and the second was drilled to 292m depth (100m percussion and 192m core). The second borehole was drilled 200m south of the first, to penetrate the formations at a greater depth and to avoid surface weathering. Fresh core from the upper Dwyka Group, the Prince Albert Formation, the Whitehill Formation, Collingham Formation and part of the Ripon Formation were successfully extracted and a detailed stratigraphic log has been drawn up. The core was sampled during extraction and the samples were immediately sent to the GFZ in Potsdam, Germany, for geochemical analyses. As suspected the black shales of the the Whitehill Formation are high in organic carbon and have an average TOC value of 4.5%, whereas the Prince Albert and Collingham Formation are below 1%. Tmax values

Economic appraisal of shale gas plays in Continental Europe

International Nuclear Information System (INIS)

Weijermars, Ruud

2013-01-01

Highlights: ► Economic feasibility of five European shale gas plays is assessed. ► Polish and Austrian shale plays appear profitable for P90 assessment criterion. ► Posidonia (Germany), Alum (Sweden) and a Turkish shale play below the hurdle rate. ► A 10% improvement of the IRR by sweet spot targeting makes all plays profitable. - Abstract: This study evaluates the economic feasibility of five emergent shale gas plays on the European Continent. Each play is assessed using a uniform field development plan with 100 wells drilled at a rate of 10 wells/year in the first decade. The gas production from the realized wells is monitored over a 25 year life cycle. Discounted cash flow models are used to establish for each shale field the estimated ultimate recovery (EUR) that must be realized, using current technology cost, to achieve a profit. Our analyses of internal rates of return (IRR) and net present values (NPVs) indicate that the Polish and Austrian shale plays are the more robust, and appear profitable when the strict P90 assessment criterion is applied. In contrast, the Posidonia (Germany), Alum (Sweden) and a Turkish shale play assessed all have negative discounted cumulative cash flows for P90 wells, which puts these plays below the hurdle rate. The IRR for P90 wells is about 5% for all three plays, which suggests that a 10% improvement of the IRR by sweet spot targeting may lift these shale plays above the hurdle rate. Well productivity estimates will become better constrained over time as geological uncertainty is reduced and as technology improves during the progressive development of the shale gas fields

Origin of oil shale

Energy Technology Data Exchange (ETDEWEB)

Cunningham-Craig, E H

1915-01-01

Kerogen was believed to be formed by the inspissation of petroleum. During this process nitrogen and sulfur compounds were concentrated in the most inspissated or weathered products. At a certain stage, reached gradually, the organic matter became insoluble in carbon-disulfide and ceased to be a bitumen. Oil shale was formed by the power of certain clays or shales to absorb inspissated petroleum, particularly unsaturated hydrocarbons. This adsorption apparently depended on the colloid content of the argillaceous rock. This rock retained these impregnated petroleum residues long after porous sandstones in the vicinity had lost all traces of petroleum by weathering and leaching.

The Multi-Porosity Multi-Permeability and Electrokinetic Natures of Shales and Their Effects in Hydraulic Fracturing of Unconventional Shale Reservoirs

Science.gov (United States)

Liu, C.; Hoang, S. K.; Tran, M. H.; Abousleiman, Y. N.

2013-12-01

Imaging studies of unconventional shale reservoir rocks have recently revealed the multi-porosity multi-permeability nature of these intricate formations. In particular, the porosity spectrum of shale reservoir rocks often comprises of the nano-porosity in the organic matters, the inter-particle micro-porosity, and the macroscopic porosity of the natural fracture network. Shale is also well-known for its chemically active behaviors, especially shrinking and swelling when exposed to aqueous solutions, as the results of pore fluid exchange with external environment due to the difference in electro-chemical potentials. In this work, the effects of natural fractures and electrokinetic nature of shale on the formation responses during hydraulic fracturing are examined using the dual-poro-chemo-electro-elasticity approach which is a generalization of the classical Biot's poroelastic formulation. The analyses show that the presence of natural fractures can substantially increase the leak-off rate of fracturing fluid into the formation and create a larger region of high pore pressure near the fracture face as shown in Fig.1a. Due to the additional fluid invasion, the naturally fractured shale swells up more and the fracture aperture closes faster compared to an intrinsically low permeability non-fractured shale formation as shown in Fig.1b. Since naturally fractured zones are commonly targeted as pay zones, it is important to account for the faster fracture closing rate in fractured shales in hydraulic fracturing design. Our results also show that the presence of negative fixed charges on the surface of clay minerals creates an osmotic pressure at the interface of the shale and the external fluid as shown in Fig.1c. This additional Donnan-induced pore pressure can result in significant tensile effective stresses and tensile damage in the shale as shown in Fig.1d. The induced tensile damage can exacerbate the problem of proppant embedment resulting in more fracture closure

Nanometer-Scale Pore Characteristics of Lacustrine Shale, Songliao Basin, NE China.

Directory of Open Access Journals (Sweden)

Min Wang

Full Text Available In shale, liquid hydrocarbons are accumulated mainly in nanometer-scale pores or fractures, so the pore types and PSDs (pore size distributions play a major role in the shale oil occurrence (free or absorbed state, amount of oil, and flow features. The pore types and PSDs of marine shale have been well studied; however, research on lacustrine shale is rare, especially for shale in the oil generation window, although lacustrine shale is deposited widely around the world. To investigate the relationship between nanometer-scale pores and oil occurrence in the lacustrine shale, 10 lacustrine shale core samples from Songliao Basin, NE China were analyzed. Analyses of these samples included geochemical measurements, SEM (scanning electron microscope observations, low pressure CO2 and N2 adsorption, and high-pressure mercury injection experiments. Analysis results indicate that: (1 Pore types in the lacustrine shale include inter-matrix pores, intergranular pores, organic matter pores, and dissolution pores, and these pores are dominated by mesopores and micropores; (2 There is no apparent correlation between pore volumes and clay content, however, a weak negative correlation is present between total pore volume and carbonate content; (3 Pores in lacustrine shale are well developed when the organic matter maturity (Ro is >1.0% and the pore volume is positively correlated with the TOC (total organic carbon content. The statistical results suggest that oil in lacustrine shale mainly occurs in pores with diameters larger than 40 nm. However, more research is needed to determine whether this minimum pore diameter for oil occurrence in lacustrine shale is widely applicable.

Burning Poseidonian shale ash for production of cement

Energy Technology Data Exchange (ETDEWEB)

1919-10-28

A process is described for the burning of shale coke obtained by the deoiling of Poseidonian or the usual kind of shale for the preparation of brick, mortar, or cement, characterized in that the shale coke is thrown on a pile and completely covered with burnt material, so that the gases drawn through this cover will be sufficiently choked to hold the feed at a high temperature as long as possible.

Scoping of fusion-driven retorting of oil shale

International Nuclear Information System (INIS)

Galloway, T.R.

1979-11-01

In the time frame beyond 2005, fusion reactors are likely to make their first appearance when the oil shale industry will probably be operating with 20% of the production derived from surface retorts operating on deep mined shale from in situ retorts and 80% from shale retorted within these in situ retorts using relatively fine shale uniformly rubblized by expensive mining methods. A process was developed where fusion reactors supply a 600 0 C mixture of nitrogen, carbon dioxide, and water vapor to both surface and in situ retorts. The in situ production is accomplished by inert gas retorting, without oxygen, avoiding the burning of oil released from the larger shale particles produced in a simpler mining method. These fusion reactor-heated gases retort the oil from four 50x50x200m in-situ rubble beds at high rate of 40m/d and high yield (i.e., 95% F.A.), which provided high return on investment around 20% for the syncrude selling at $20/bbl, or 30% if sold as $30/bbl for heating oil. The bed of 600 0 C retorted shale, or char, left behind was then burned by the admission of ambient air in order to recover all of the possible energy from the shale resource. The hot combustion gases, mostly nitrogen, carbon dioxide and water vapor are then heat-exchanged with fusion reactor blanket coolant flow to be sequentially introduced into the next rubble bed ready for retorting. The advantages of this fusion-driven retorting process concept are a cheaper mining method, high yield and higher production rate system, processing with shale grades down to 50 l/mg (12 gpt), improved resource recovery by complete char utilization and low energy losses by leaving behind a cold, spent bed

Pore Structure and Fractal Characteristics of Niutitang Shale from China

Directory of Open Access Journals (Sweden)

Zhaodong Xi

2018-04-01

Full Text Available A suite of shale samples from the Lower Cambrian Niutitang Formation in northwestern Hunan Province, China, were investigated to better understand the pore structure and fractal characteristics of marine shale. Organic geochemistry, mineralogy by X-ray diffraction, porosity, permeability, mercury intrusion and nitrogen adsorption and methane adsorption experiments were conducted for each sample. Fractal dimension D was obtained from the nitrogen adsorption data using the fractal Frenkel-Halsey-Hill (FHH model. The relationships between total organic carbon (TOC content, mineral compositions, pore structure parameters and fractal dimension are discussed, along with the contributions of fractal dimension to shale gas reservoir evaluation. Analysis of the results showed that Niutitang shale samples featured high TOC content (2.51% on average, high thermal maturity (3.0% on average, low permeability and complex pore structures, which are highly fractal. TOC content and mineral compositions are two major factors affecting pore structure but they have different impacts on the fractal dimension. Shale samples with higher TOC content had a larger specific surface area (SSA, pore volume (PV and fractal dimension, which enhanced the heterogeneity of the pore structure. Quartz content had a relatively weak influence on shale pore structure, whereas SSA, PV and fractal dimension decreased with increasing clay mineral content. Shale with a higher clay content weakened pore structure heterogeneity. The permeability and Langmuir volume of methane adsorption were affected by fractal dimension. Shale samples with higher fractal dimension had higher adsorption capacity but lower permeability, which is favorable for shale gas adsorption but adverse to shale gas seepage and diffusion.

Intelligent fracture creation for shale gas development

KAUST Repository

Douglas, Craig C.; Qin, Guan; Collier, Nathan; Gong, Bin

2011-01-01

Shale gas represents a major fraction of the proven reserves of natural gas in the United States and a collection of other countries. Higher gas prices and the need for cleaner fuels provides motivation for commercializing shale gas deposits even

Prospect of shale gas recovery enhancement by oxidation-induced rock burst

Directory of Open Access Journals (Sweden)

Lijun You

2017-11-01

Full Text Available By horizontal well multi-staged fracturing technology, shale rocks can be broken to form fracture networks via hydraulic force and increase the production rate of shale gas wells. Nonetheless, the fracturing stimulation effect may be offset by the water phase trapping damage caused by water retention. In this paper, a technique in transferring the negative factor of fracturing fluid retention into a positive factor of changing the gas existence state and facilitating shale cracking was discussed using the easy oxidation characteristics of organic matter, pyrite and other minerals in shale rocks. Furthermore, the prospect of this technique in tackling the challenges of large retention volume of hydraulic fracturing fluid in shale gas reservoirs, high reservoir damage risks, sharp production decline rate of gas wells and low gas recovery, was analyzed. The organic matter and pyrite in shale rocks can produce a large number of dissolved pores and seams to improve the gas deliverability of the matrix pore throats to the fracture systems. Meanwhile, in the oxidation process, released heat and increased pore pressure will make shale rock burst, inducing expansion and extension of shale micro-fractures, increasing the drainage area and shortening the gas flowing path in matrix, and ultimately, removing reservoir damage and improving gas recovery. To sum up, the technique discussed in the paper can be used to “break” shale rocks via hydraulic force and to “burst” shale rocks via chemical oxidation by adding oxidizing fluid to the hydraulic fracturing fluid. It can thus be concluded that this method can be a favorable supplementation for the conventional hydraulic fracturing of shale gas reservoirs. It has a broad application future in terms of reducing costs and increasing profits, maintaining plateau shale gas production and improving shale gas recovery.

Stabilization of gasoline from shale

Energy Technology Data Exchange (ETDEWEB)

Benedetti, L

1929-03-14

A process is described of stabilizing gasoline from shale, consisting in treating by agitating the gasoline freshly distilled from shale oil with 1.5 percent of its weight of sulfuric acid diluted to more than 10 times its volume, after which separating the pyridine, then treating by agitating with sulfuric acid which treatment separates the unsaturated hydrocarbons and finally treating by agitating with 1.5 percent of its weight of saturated caustic soda solution and washing with water.

Plan for addressing issues relating to oil shale plant siting

Energy Technology Data Exchange (ETDEWEB)

Noridin, J. S.; Donovan, R.; Trudell, L.; Dean, J.; Blevins, A.; Harrington, L. W.; James, R.; Berdan, G.

1987-09-01

The Western Research Institute plan for addressing oil shale plant siting methodology calls for identifying the available resources such as oil shale, water, topography and transportation, and human resources. Restrictions on development are addressed: land ownership, land use, water rights, environment, socioeconomics, culture, health and safety, and other institutional restrictions. Descriptions of the technologies for development of oil shale resources are included. The impacts of oil shale development on the environment, socioeconomic structure, water availability, and other conditions are discussed. Finally, the Western Research Institute plan proposes to integrate these topics to develop a flow chart for oil shale plant siting. Western Research Institute has (1) identified relative topics for shale oil plant siting, (2) surveyed both published and unpublished information, and (3) identified data gaps and research needs. 910 refs., 3 figs., 30 tabs.

Gas pressure from a nuclear explosion in oil shale

International Nuclear Information System (INIS)

Taylor, R.W.

1975-01-01

The quantity of gas and the gas pressure resulting from a nuclear explosion in oil shale is estimated. These estimates are based on the thermal history of the rock during and after the explosion and the amount of gas that oil shale releases when heated. It is estimated that for oil shale containing less than a few percent of kerogen the gas pressure will be lower than the hydrostatic pressure. A field program to determine the effects of nuclear explosions in rocks that simulate the unique features of oil shale is recommended. (U.S.)

Desulfurization of Jordanian oil shale

International Nuclear Information System (INIS)

Abu-Jdayil, B. M.

1990-01-01

Oxy desulfurization process and caustic treatment were applied in this work to remove sulfur from Jordanian oil shale. The oxy desulfurization process has been studied in a batch process using a high pressure autoclave, with constant stirring speed, and oxygen and water were used as desulfurizing reagents. Temperature, oxygen pressure, batch time, and particle size were found to be important process variables, while solid/liquid ratio was found to have no significant effect on the desulfurization process. The response of different types of oil shale to this process varied, and the effect of the process variables on the removal of total sulfur, pyritic sulfur, organic sulfur, total carbon, and organic carbon were studied. An optimum condition for oxy desulfurization of El-Lajjun oil shale, which gave maximum sulfur removal with low loss of carbon, was determined from the results of this work. The continuous reaction model was found to be valid, and the rate of oxidation for El-Lajjun oil shale was of the first order with respect to total sulfur, organic sulfur, total carbon, and organic carbon. For pyritic sulfur oxidation, the shrinking core model was found to hold and the rate of reaction controlled by diffusion through product ash layer. An activation energy of total sulfur, organic sulfur, pyritic sulfur, total carbon, and organic carbon oxidation was calculated for the temperature range of 130 -190 degrees celsius. In caustic treatment process, aqueous sodium hydroxide at 160 degrees celsius was used to remove the sulfur from El-Lajjun oil shale. The variables tested (sodium hydroxide concentration and treatment time) were found to have a significant effect. The carbon losses in this process were less than in the oxy desulfurization process. 51 refs., 64 figs., 121 tabs. (A.M.H.)

Prospects for the exploitation of Jordan oil shale

International Nuclear Information System (INIS)

Jaber, J.O; Probert, S.D.; Badr, O.

1997-01-01

Oil shale is the major indigenous fossil-fuel in Jordan: its predicted reserves, of about 5·10 1 0 tonnes, should be sufficient to satisfy Jordan's energy requirements for several centuries. Jordanian oil shale has, on an average, a gross calorific value of between 5 and 7 MJ/kg, an oil yield of ∼ 10 %, and a sulfur content of approximately 3 % by weight of the raw shale (i.e. 7 to 9 % of the organic matter content). Using the oil shale as the input fuel, a multipurpose production process (i.e. retorting, electricity generation, thermal water-desalination, chemicals production as well as mineral extraction) could achieve high utilisation-factors of both its chemical and energy potentials. In the long-term, oil shale is the only indigenous energy resource that could reduce Jordan's dependence on imported crude oil and hence ease the pressure on the national economy. The conversion of oil shale into a liquid or gaseous fuel and raw materials will be of decisive importance in attempts to secure the future of energy supplies. So national efforts devoted to the exploration for, and harnessing more economically, this energy resource, while limiting the associated adverse environmental impacts, should be accelerated. (author)

Chemical kinetics and oil shale process design

Energy Technology Data Exchange (ETDEWEB)

Burnham, A.K.

1993-07-01

Oil shale processes are reviewed with the goal of showing how chemical kinetics influences the design and operation of different processes for different types of oil shale. Reaction kinetics are presented for organic pyrolysis, carbon combustion, carbonate decomposition, and sulfur and nitrogen reactions.

The Lower Jurassic Posidonia Shale in southern Germany: results of a shale gas analogue study

Science.gov (United States)

Biermann, Steffen; Schulz, Hans-Martin; Horsfield, Brian

2013-04-01

The shale gas potential of Germany was recently assessed by the Federal Institute for Geosciences and Natural Resources (2012 NiKo-Project) and is - in respect of the general natural gas occurrence in Germany - regarded as a good alternative hydrocarbon source. The Posidonia Shale in northern and southern Germany is one of the evaluated rock formation and easily accessible in outcrops in the Swabian Alps (southern Germany). The area of interest in this work is located in such an outcrop that is actively used for open pit mining next to the town of Dotternhausen, 70 km southwest of Stuttgart. 31 samples from the quarry of Dotternhausen were analyzed in order to characterize the immature Posidonia Shale (Lower Toarcian, Lias ɛ) of southern Germany as a gas shale precursor. Methods included are Rock Eval, Open Pyrolysis GC, SEM, Mercury Intrusion Porosimetry, XRD, and other. The samples of Dotternhausen contain exclusively type II kerogen. The majority of the organic matter is structureless and occurs in the argillaceous-calcareous matrix. Structured organic matter appears predominantly as alginite, in particular the algae "tasmanite" is noticeable. The TOC content ranges up to 16 wt% with a high bitumen content. The mineral content characterizes the Posidonia Shale as a marlstone or mudstone with varying clay-calcite ratios. The quartz and pyrite content reaches up to 20 wt% and 9 wt%, respectively. The rock fabric is characterized by a fine grained and laminated matrix. The mean porosity lies between 4 and 12 %. Fractures other than those introduced by sample preparation were not observed. The Posidonia Shale is predicted to have an excellent source rock potential and will generate intermediate, P-N-A low wax oil when exposed to higher P-T-conditions ("oil kitchen"). Contact surfaces between the kerogen and matrix will be vulnerable to pressure induced fracturing caused by hydrocarbon formation. Additional porosity will be formed during maturation due to the

Clay squirt: Local flow dispersion in shale-bearing sandstones

DEFF Research Database (Denmark)

Sørensen, Morten Kanne; Fabricius, Ida Lykke

2017-01-01

Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

Devonian and Lower Carboniferous Conodonts of the Cantabrian Mountains (Spain) and their stratigraphic application

NARCIS (Netherlands)

Adrichem Boogaert, van H.A.

1967-01-01

A short review of the literature on the stratigraphy of the Devonian and the Lower Carboniferous of the Cantabrian Mountains precedes the report of the author's stratigraphic and palaeontologic observations in León: the Río Esla area (Gedinnian to Viséan), the central Cantabrian area (Famennian to

Environmental control costs for oil shale processes

Energy Technology Data Exchange (ETDEWEB)

None

1979-10-01

The studies reported herein are intended to provide more certainty regarding estimates of the costs of controlling environmental residuals from oil shale technologies being readied for commercial application. The need for this study was evident from earlier work conducted by the Office of Environment for the Department of Energy Oil Shale Commercialization Planning, Environmental Readiness Assessment in mid-1978. At that time there was little reliable information on the costs for controlling residuals and for safe handling of wastes from oil shale processes. The uncertainties in estimating costs of complying with yet-to-be-defined environmental standards and regulations for oil shale facilities are a critical element that will affect the decision on proceeding with shale oil production. Until the regulatory requirements are fully clarified and processes and controls are investigated and tested in units of larger size, it will not be possible to provide definitive answers to the cost question. Thus, the objective of this work was to establish ranges of possible control costs per barrel of shale oil produced, reflecting various regulatory, technical, and financing assumptions. Two separate reports make up the bulk of this document. One report, prepared by the Denver Research Institute, is a relatively rigorous engineering treatment of the subject, based on regulatory assumptions and technical judgements as to best available control technologies and practices. The other report examines the incremental cost effect of more conservative technical and financing alternatives. An overview section is included that synthesizes the products of the separate studies and addresses two variations to the assumptions.

Fugitive Emissions from the Bakken Shale Illustrate Role of Shale Production in Global Ethane Shift

Science.gov (United States)

Kort, E. A.; Smith, M. L.; Murray, L. T.; Gvakharia, A.; Brandt, A. R.; Peischl, J.; Ryerson, T. B.; Sweeney, C.; Travis, K.

2016-01-01

Ethane is the second most abundant atmospheric hydrocarbon, exerts a strong influence on tropospheric ozone, and reduces the atmosphere's oxidative capacity. Global observations showed declining ethane abundances from 1984 to 2010, while a regional measurement indicated increasing levels since 2009, with the reason for this subject to speculation. The Bakken shale is an oil and gas-producing formation centered in North Dakota that experienced a rapid increase in production beginning in 2010. We use airborne data collected over the North Dakota portion of the Bakken shale in 2014 to calculate ethane emissions of 0.23 +/- 0.07 (2 sigma) Tg/yr, equivalent to 1-3% of total global sources. Emissions of this magnitude impact air quality via concurrent increases in tropospheric ozone. This recently developed large ethane source from one location illustrates the key role of shale oil and gas production in rising global ethane levels.

Life-cycle analysis of shale gas and natural gas.

Energy Technology Data Exchange (ETDEWEB)

Clark, C.E.; Han, J.; Burnham, A.; Dunn, J.B.; Wang, M. (Energy Systems); ( EVS)

2012-01-27

The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. Using the current state of knowledge of the recovery, processing, and distribution of shale gas and conventional natural gas, we have estimated up-to-date, life-cycle greenhouse gas emissions. In addition, we have developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps - such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings - that need to be addressed further. Our base case results show that shale gas life-cycle emissions are 6% lower than those of conventional natural gas. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty regarding whether shale gas emissions are indeed lower than conventional gas emissions. This life-cycle analysis provides insight into the critical stages in the natural gas industry where emissions occur and where opportunities exist to reduce the greenhouse gas footprint of natural gas.

Comparative dermal carcinogenesis of shale and petroleum-derived distillates.

Science.gov (United States)

Clark, C R; Walter, M K; Ferguson, P W; Katchen, M

1988-03-01

Ten test materials derived from petroleum or hydrotreated shale oils were applied 3 times/week for up to 105 weeks to the shaved skin of 25 male and 25 female C3H/HeN mice per group. Mineral oil and benzo(a) pyrene (0.15%) were control materials. Clinical observations were recorded during the study. At death, histopathologic examination was conducted on skin, internal organs and any gross lesions. Exposures to some materials were ended midway in the study due to severe irritation. Chronic toxicity of all materials was limited to inflammatory and degenerative skin changes. Significant increases over control incidence of skin tumors (squamous cell carcinoma and fibrosarcoma) occurred with both petroleum and shale-derived naphtha (21%, 50%), Jet A (26%, 28%), JP-4 (26%, 50%), and crude oils (84%, 54%). Severely hydrotreated shale oil and petroleum and shale-derived diesel distillates were not considered tumorigenic. Results indicate that toxicity of comparable petroleum and shale-derived fractions was qualitatively similar and confirm earlier findings that hydrotreating reduces or eliminates carcinogenicity of raw shale oil.

Phanerozoic environments of black shale deposition and the Wilson Cycle

Directory of Open Access Journals (Sweden)

J. Trabucho-Alexandre

2012-02-01

Full Text Available The spatial and temporal distribution of black shales is related to the development of environments in which they accumulate and to a propitious combination of environmental variables. In recent years, much has been done to improve our understanding of the mechanisms behind the temporal distribution of black shales in the Phanerozoic and of the environmental variables that result in their deposition. However, the interpretation of ancient black shale depositional environments is dominated by an oversimplistic set of three depositional models that do not capture their complexity and dynamics. These three models, the restricted circulation, the (open ocean oxygen minimum and the continental shelf models, are an oversimplification of the variety of black shale depositional environments that arise and coexist throughout the course of a basin's Wilson Cycle, i.e. the dynamic sequence of events and stages that characterise the evolution of an ocean basin, from the opening continental rift to the closing orogeny. We examine the spatial distribution of black shales in the context of the Wilson Cycle using examples from the Phanerozoic. It is shown that the geographical distribution of environments of black shale deposition and the position of black shales in the basin infill sequence strongly depend on basin evolution, which controls the development of sedimentary environments where black shales may be deposited. The nature of the black shales that are deposited, i.e. lithology and type of organic matter, also depends on basin evolution and palaeogeography. We propose that in studies of black shales more attention should be given to the sedimentary processes that have led to their formation and to the interpretation of their sedimentary environments.

Shale gas vs. coal: Policy implications from environmental impact comparisons of shale gas, conventional gas, and coal on air, water, and land in the United States

International Nuclear Information System (INIS)

Jenner, Steffen; Lamadrid, Alberto J.

2013-01-01

The aim of this paper is to examine the major environmental impacts of shale gas, conventional gas and coal on air, water, and land in the United States. These factors decisively affect the quality of life (public health and safety) as well as local and global environmental protection. Comparing various lifecycle assessments, this paper will suggest that a shift from coal to shale gas would benefit public health, the safety of workers, local environmental protection, water consumption, and the land surface. Most likely, shale gas also comes with a smaller GHG footprint than coal. However, shale gas extraction can affect water safety. This paper also discusses related aspects that exemplify how shale gas can be more beneficial in the short and long term. First, there are technical solutions readily available to fix the most crucial problems of shale gas extraction, such as methane leakages and other geo-hazards. Second, shale gas is best equipped to smoothen the transition to an age of renewable energy. Finally, this paper will recommend hybrid policy regulations. - Highlights: ► We examine the impacts of (un)conventional gas and coal on air, water, and land. ► A shift from coal to shale gas would benefit public health. ► Shale gas extraction can affect water safety. ► We discuss technical solutions to fix the most crucial problems of shale gas extraction. ► We recommend hybrid regulations.

Method of recovering hydrocarbons from oil shale

Energy Technology Data Exchange (ETDEWEB)

Walton, D.K.; Slusser, M.S.

1970-11-24

A method is described for recovering hydrocarbons from an oil-shale formation by in situ retorting. A well penetrating the formation is heated and gas is injected until a pressure buildup within the well is reached, due to a decrease in the conductivity of naturally occurring fissures within the formation. The well is then vented, in order to produce spalling of the walls. This results in the formation of an enlarged cavity containing rubberized oil shale. A hot gas then is passed through the rubberized oil shale in order to retort hydrocarbons and these hydrocarbons are recovered from the well. (11 claims)

Duvernay shale lithofacies distribution analysis in the West Canadian Sedimentary Basin

Science.gov (United States)

Zhu, Houqin; Kong, Xiangwen; Long, Huashan; Huai, Yinchao

2018-02-01

In the West Canadian Sedimentary Basin (WCSB), Duvernay shale is considered to contribute most of the Canadian shale gas reserve and production. According to global shale gas exploration and development practice, reservoir property and well completion quality are the two key factors determining the shale gas economics. The two key factors are strongly depending on shale lithofacies. On the basis of inorganic mineralogy theory, all available thin section, X-ray diffraction, scanning electron microscope (SEM), energy dispersive spectrometer (EDS) data were used to assist lithofacies analysis. Gamma ray (GR), acoustic (AC), bulk density (RHOB), neutron porosity (NPHI) and photoelectric absorption cross-section index (PE) were selected for log response analysis of various minerals. Reservoir representative equation was created constrained by quantitative core analysis results, and matrix mineral percentage of quartz, carbonate, feldspar and pyrite were calculated to classify shale lithofacies. Considering the horizontal continuity of seismic data, rock physics model was built, and acoustic impedance integrated with core data and log data was used to predict the horizontal distribution of different lithofacies. The results indicate that: (1) nine lithofacies can be categorized in Duvernay shale, (2) the horizontal distribution of different lithofacies is quite diversified, siliceous shale mainly occurs in Simonette area, calcareous shale is prone to develop in the vicinity of reef, while calcareous-siliceous shale dominates in Willesdon Green area.

Distillation of oil shales

Energy Technology Data Exchange (ETDEWEB)

Bronder, G A

1926-03-22

To distill oil shales, cannel coals, and other carbonaceous materials for the extraction therefrom of hydrocarbons and volatile nitrogenous compounds, hard non-condensable gases from the condensers and scrubbers are withdrawn by blowers and admixed with burnt gases, obtained through conduits from the flues of heaters, and forced downwardly through horizontal chambers, connected by vertical conduits, of the heaters and delivered into the retort beneath the grate. Passing upwardly through the charge they vaporize the volatile substances in the shale, and a suction pump removes the vapors from the top of the retort. Immediately they are produced and at substantially the same temperature as that at which they emanate, thus preventing cracking of the oil vapors and condensation of the oil at the top of the retort. The amount of burnt flue gas admixed with the hard gases is regulated by two valves until a required uniform temperature is obtained. A generator supplies producer gas to a heater at the commencement of the retorting operation for circulation through the shale charge to initially produce oil vapors. The generator is connected by a pipe to the gas conduit leading to blowers.

Wellbore stability in shales considering chemo-poroelastic effects

Energy Technology Data Exchange (ETDEWEB)

Araujo, Ewerton M.P.; Pastor, Jorge A.S.C.; Fontoura, Sergio A.B.; Rabe, Claudio [Pontificia Univ. Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil). Dept. de Engenharia Civil. Grupo de Tecnologia e Engenharia de Petroleo

2004-07-01

Under compaction and low geothermal gradients are deep water characteristics. Both under compaction and low geothermal gradients generate considerable thickness of smectite-rich shales. These rocks are the major source of wellbore stability problems, because they are susceptible to adverse physico-chemical reactions when in contact with inadequate drilling fluids. Due shales are low permeability rocks diffusion processes dominate the changes of pore pressure around wellbore. Diffusion of fluids, ions and temperature occurs in shales during drilling and demand a fully coupled modelling taking account these factors. Despite temperature importance, in this paper wellbore stability in shales is analyzed through a model that considers only the coupling between poroelastic and physico-chemical effects. The coupled equations are solved analytically and have been implemented in a computational simulator with user-friendly interface. Time-dependent simulations of wellbore stability in shales are presented for a typical deep water scenario. The results show that physico-chemical effects change pore pressure around wellbore and have high impact on the wellbore stability. (author)

Breakthrough and prospect of shale gas exploration and development in China

Directory of Open Access Journals (Sweden)

Dazhong Dong

2016-01-01

Full Text Available In the past five years, shale gas exploration and development has grown in a leaping-forward way in China. Following USA and Canada, China is now the third country where industrial shale gas production is realized, with the cumulative production exceeding 60 × 108 m3 until the end of 2015. In this paper, the main achievements of shale gas exploration and development in China in recent years were reviewed and the future development prospect was analyzed. It is pointed out that shale gas exploration and development in China is, on the whole, still at its early stage. Especially, marine shale gas in the Sichuan Basin has dominated the recent exploration and development. For the realization of shale gas scale development in China, one key point lies in the breakthrough and industrial production of transitional facies and continental facies shale gas. Low–moderate yield of shale gas wells is the normal in China, so it is crucial to develop key exploration and development technologies. Especially, strictly controlling single well investment and significantly reducing cost are the important means to increase shale gas exploration and development benefits. And finally, suggestions were proposed in five aspects. First, continuously strengthen theoretical and technical researches, actively carry out appraisal on shale gas “sweet spots”, and gradually accumulate development basis. Second, stress on primary evaluation of exploration and development, highlight the effective implementation of shale gas resources, and control the rhythm of appraisal drilling and productivity construction. Third, highlight fine description and evaluation of shale gas reservoirs and increase the overall development level. Fourth, intensify the research on exploration and development technologies in order to stand out simple and practical technologies with low costs. And fifth, summarize the experiences in fast growth of shale gas exploration and development, highlight

Pengaruh Proses Pelapukan Clay Shale terhadap Perubahan Parameter Rasio Disintegritas (DR

Directory of Open Access Journals (Sweden)

Idrus M Alatas

2017-04-01

Full Text Available The background of this research because of the frequent occurrence of the failure in the geotechnical design of clay shale caused by weathering. Disintegration ratio is a comparison of physical changes due to weathering at certain times of the initial conditions. Changes in physical properties due to clay shale weathering determined by the disintegration ratio (DR.Clay shale weathering will occur more quickly as a result of wetting and drying cycles when compared with the drying process. While due to the increased number of cycles of wetting at the same time, causing weathering on clay shale will be faster again. Until the 80th day of drying time, the magnitude DRof Semarang-Bawenclay shaleand Hambalang are the same, namely DR = 0.916 (completelly durable. However, due to wetting and drying cycles on day 32, samples of Semarang-Bawenclay shale is DR = 0.000 or non durable completelly, while on Hambalang clay shale in same day DR between 0.2117 to 0.3344. Generally Semarang-Bawen clay shale will be faster weathered than Hambalang clay shale. It is caused by the mineralogy content of Semarang-Bawen clay shale has dominated by Smectite, and Hambalangclay shalehas dominated mineral Kaolinite and Illlite.

Problem of Production of Shale Gas in Germany

OpenAIRE

Nataliya K. Meden

2014-01-01

A bstract: Our magazine publishes a series of articles on shale gas in different countries. This article is about Germany, a main importer of Russian natural gas, so a perspective of exploitation of local shale gas resources is of a clear practical importance for Russia. We discuss external and internal factors which determine position of the German government concerning the shale gas excavation: policy of the USA and the EU, positions of German political parties, influence of the lobbying co...

Oil shales of the Lothians, Part III, the chemistry of the oil shales

Energy Technology Data Exchange (ETDEWEB)

Steuart, D R

1912-01-01

Tests were performed whereby fuller's earth and lycopodium spore dust were heated to retorting temperatures and the crude oil examined. Oil shale may be composed of the following: Vegetable matter that has been macerated and preserved by combining with salts, spores, and other such material that has been protected from decay, and a proportion of animal matter. Generally, oil shale may be considered as a torbanite that contains a large proportion of inorganic matter, or it may be a torbanite that has deteriorated with age. This supposition is based on the fact that oil yield decreases and the yield of ammonia increases with age.

Thermal effects in shales: measurements and modeling

International Nuclear Information System (INIS)

McKinstry, H.A.

1977-01-01

Research is reported concerning thermal and physical measurements and theoretical modeling relevant to the storage of radioactive wastes in a shale. Reference thermal conductivity measurements are made at atmospheric pressure in a commercial apparatus; and equipment for permeability measurements has been developed, and is being extended with respect to measurement ranges. Thermal properties of shales are being determined as a function of temperature and pressures. Apparatus was developed to measure shales in two different experimental configurations. In the first, a disk 15 mm in diameter of the material is measured by a steady state technique using a reference material to measure the heat flow within the system. The sample is sandwiched between two disks of a reference material (single crystal quartz is being used initially as reference material). The heat flow is determined twice in order to determine that steady state conditions prevail; the temperature drop over the two references is measured. When these indicate an equal heat flow, the thermal conductivity of the sample can be calculated from the temperature difference of the two faces. The second technique is for determining effect of temperature in a water saturated shale on a larger scale. Cylindrical shale (or siltstone) specimens that are being studied (large for a laboratory sample) are to be heated electrically at the center, contained in a pressure vessel that will maintain a fixed water pressure around it. The temperature is monitored at many points within the shale sample. The sample dimensions are 25 cm diameter, 20 cm long. A micro computer system has been constructed to monitor 16 thermocouples to record variation of temperature distribution with time

shales: a review of their classifications, properties and importance to ...

African Journals Online (AJOL)

DJFLEX

In the Niger Delta petroleum province, the source rocks and seal rocks are the marine/deltaic, plastic and over-pressured shales of Akata and Agbada Formations. KEY WORDS: Shales, Classification, Strength, Composition, Petroleum Industry, Niger Delta. INTRODUCTION. Shales are fine-grained laminated or fissile.

Study on geochemical occurrences of REE in Wangqing oil shale

Energy Technology Data Exchange (ETDEWEB)

Bai, Jing-ru; Wang, Qing; Liu, Tong; Wei, Yan-zhen; Bai, Zhang [Northeast Dianli Univ., Jilin (China). Engineering Research Centre

2013-07-01

Sequential chemical extraction experiment (SCEE) and Float- sink experiment (FSE) have been employed on oil shale research from Wangqing, Jilin province China, in order to determine the binding forms of rare earth elements (REE) in oil shale. The REE contents were determined by the inductively coupled plasma-mass spectrometry (ICP-MS). Wangqing oil shale was screened into specific gravity density level: <1.5g/cm{sup 3}, 1.5-1.6g/cm{sup 3}, 1.6-2.0g/cm{sup 3}, 2.0-2.4g/cm{sup 3}, >2.4g/cm{sup 3}. The mode of occurrences of rare earth elements in Wangqing oil shale was studied by six-step SCEE. FSE results show that REEs in Wangqing oil shale exist mainly in inorganic minerals and more in excluded mineral, while SCEE results show that REEs of Wangqing oil shale is primarily occurred in minerals, including carbonate, Fe-Mn oxide, sulfide, and Si-minerals. FSE and SCEE results fully illustrate excluded mineral is mainly mode of occurrence of REEs in Wangqing oil shale, whereas inorganic minerals and organic matter is not that. The REE distribution pattern curves of FSE density and SCEE fraction products are similar with that of raw oil shale. The REE in different densities products has a close connection with terrigenous clastic rock, and the supply of terrestrial material is stable.

Thermocatalytical processing of coal and shales

Directory of Open Access Journals (Sweden)

Zhaksyntay Kairbekov

2012-12-01

Full Text Available The article investigates the questions of thermocatalytical conversion of organic mass of coal (OMC, it is shown that in the absence of a catalyst process is carried out by a radical process. Accumulated data on the properties for radicals of different structure and therefore different reaction capacity enables us to understand and interpret the conversion of OMC. Thermal conversion of OMC regarded as a kind of depolymerization, accompanied by decomposition of the functional groups with the formation of radicals, competing for hydrogen atom. Catalyst can change the direction and conditions of the process. Modern catalysts can reduce the process pressure up to 50 atm., with a high degree of coal conversion. We consider examples of simultaneous conversion of coal and shale, shale and masut, shale and tar.

Investigating Rare Earth Element Systematics in the Marcellus Shale

Science.gov (United States)

Yang, J.; Torres, M. E.; Kim, J. H.; Verba, C.

2014-12-01

The lanthanide series of elements (the 14 rare earth elements, REEs) have similar chemical properties and respond to different chemical and physical processes in the natural environment by developing unique patterns in their concentration distribution when normalized to an average shale REE content. The interpretation of the REE content in a gas-bearing black shale deposited in a marine environment must therefore take into account the paleoredox conditions of deposition as well as any diagenetic remobilization and authigenic mineral formation. We analyzed 15 samples from a core of the Marcellus Shale (Whipkey ST1, Greene Co., PA) for REEs, TOC, gas-producing potential, trace metal content, and carbon isotopes of organic matter in order to determine the REE systematics of a black shale currently undergoing shale gas development. We also conducted a series of sequential leaching experiments targeting the phosphatic fractions in order to evaluate the dominant host phase of REEs in a black shale. Knowledge of the REE system in the Marcellus black shale will allow us to evaluate potential REE release and behavior during hydraulic fracturing operations. Total REE content of the Whipkey ST1 core ranged from 65-185 μg/g and we observed three distinct REE shale-normalized patterns: middle-REE enrichment (MREE/MREE* ~2) with heavy-REE enrichment (HREE/LREE ~1.8-2), flat patterns, and a linear enrichment towards the heavy-REE (HREE/LREE ~1.5-2.5). The MREE enrichment occurred in the high carbonate samples of the Stafford Member overlying the Marcellus Formation. The HREE enrichment occurred in the Union Springs Member of the Marcellus Formation, corresponding to a high TOC peak (TOC ~4.6-6.2 wt%) and moderate carbonate levels (CaCO3 ~4-53 wt%). Results from the sequential leaching experiments suggest that the dominant host of the REEs is the organic fraction of the black shale and that the detrital and authigenic fractions have characteristic MREE enrichments. We present our

Shale processing

Energy Technology Data Exchange (ETDEWEB)

Hampton, W H

1928-05-29

The process of treating bituminiferous solid materials such as shale or the like to obtain valuable products therefrom, which comprises digesting a mixture of such material in comminuted condition with a suitable digestion liquid, such as an oil, recovering products vaporized in the digestion, and separating residual solid matter from the digestion liquid by centrifuging.

Carbon and nitrogen isotopic analysis of coral-associated nitrogen in rugose corals of the Middle Devonian, implications for paleoecology and paleoceanography.

Science.gov (United States)

Hickey, A. N.; Junium, C. K.; Uveges, B. T.; Ivany, L. C.; Martindale, R. C.

2017-12-01

The Middle Devonian Appalachian Basin of Central New York hosts an extraordinary diversity of well-studied fossil invertebrates within the shallow marine sequences of the Givetian Age, Hamilton Group. Of particular interest are a series of aerially expansive coral beds with diverse assemblages of rugose corals. These well-preserved specimens provide an excellent opportunity to test the feasibility of δ15N and δ13C analyses in rugose corals in an effort to resolve outstanding issues regarding their paleoecology and ontogeny as well environmental dynamics within the Devonian Appalachian Basin. Here we present carbon and nitrogen isotope analyses of the rugose corals Heliophyllum and Siphonophrentis from the Joshua Coral Bed. Corals were cleaned of the host calcareous shale and sonicated sequentially in deionized water and methanol, and then oxidatively cleaned. Cleaned corals were sectioned into 0.5cm billets to obtain enough residual organic material for analysis. The organic content of the corals is low, but nanoEA allows for serial sampling of 5-10 samples per coral. Coral sections were decarbonated and the residual organic material is filtered and dried prior to analysis. Coral organic matter is analyzed in triplicate using nanoEA, which is a cryo-trapping, capillary focusing technique for δ15N and δ13C. The δ15N of organic matter extracted from rugose corals is, on average, enriched by 2-4‰ relative to the bulk nitrogen in the host rock. As well, the δ13C of organic carbon from the corals is 13C-enriched relative to the bulk rock, but to a lesser degree (no more than 1.5‰). Assuming that the bulk rock carbon and nitrogen are largely representative of the long-term primary production background, the modest enrichment is consistent with a trophic effect, and that rugose corals are likely planktivores. In an individual coral, δ15N ranges by 3-4‰ over its length, and when adjusted for trophic enrichment varies around the average δ15N of bulk

Dolomitization and sedimentary cyclicity of the Ordovician, Silurian, and Devonian rocks in South Estonia

Directory of Open Access Journals (Sweden)

Kallaste, Toivo

2006-03-01

Full Text Available The distribution and composition of dolomitized rocks and stoichiometry of dolomite in southern Estonia in the Ordovician, Silurian, and Devonian were studied on the background of the facies, sedimentary cyclicity (nine shallowing-up cycles, and evolution of the palaeobasins. The composition of rocks and lattice parameters of dolomite were investigated using the X-ray diffraction, X-ray fluorescence, titration and gravimetric analyses, and porosity measurements. The formation of dolostones is directly determined by the cyclic evolution of palaeobasins. Dolomitized rocks belong to the shallow-water inner shelf or tidal/lagoonal facies belt of regressive phases of sedimentary cycles. Sediments of the deep shelf/transitional environment and transgressive phases are not dolomitized. The most stoichiometric is secondary replacive dolomite of Silurian and upper Ordovician dolostones, formed during the early diagenesis of normal-marine (saline shallow-shelf calcitic sediments. The content of insoluble residue does not affect the stoichiometry. The changes in lattice parameters are induced by the Ca/Mg ratio in the dolomite lattice. The dolomite of the dolostones contacting limestone or containing calcite has an expanded lattice. The primary (syngenetic dolostone of the lagoonal or tidal flat belt has also an expanded lattice. No dolomitizing effect of the waters of the Devonian palaeobasin on the underlying rocks was revealed. The whole data set of the studied dolostones is consistent with the marine water environment in the palaeobasin at the corresponding time and shows no sign of the inflow of external fluids. It suggests that the microbial model of dolomite formation may characterize the Ordovician, Silurian, and Devonian in southern Estonia. The occurrence of dolostones between undolomitized rocks limits the time of dolomitization to the early diagenetic stage.

Ichnologic Note. Evidence of Predation on the Rugose Coral Calceola Sandalina (Devonian, Czech Republic)

Czech Academy of Sciences Publication Activity Database

Galle, Arnošt; Mikuláš, Radek

2003-01-01

Roč. 10, - (2003), s. 37-41 ISSN 1042-0940 R&D Projects: GA AV ČR IAA3013207 Institutional research plan: CEZ:AV0Z3013912 Keywords : corals * Calceola * Devonian Subject RIV: DB - Geology ; Mineralogy http://rzblx1.uni-regensburg.de/ezeit/detail.phtml?bibid=CASCR&colors=7&lang=en&jour_id=41560

Production of oil from Israeli oil shale

International Nuclear Information System (INIS)

Givoni, D.

1993-01-01

Oil shale can be utilized in two-ways: direct combustion to generate steam and power or retorting to produce oil or gas. PAMA has been developing both direct combustion and retorting processes. Its main effort is in the combustion. An oil shale fired steam boiler was erected in the Rotem industrial complex for demonstration purposes. PAMA has also been looking into two alternative retorting concepts - slow heating of coarse particles and fast heating of fine particles. The present paper provides operating data of oil shale processing in the following scheme: (a) retorting in moving bed, pilot and bench scale units, and (b) retorting in a fluidized bed, bench scale units. (author)

Investigation of the dielectric properties of shale

International Nuclear Information System (INIS)

Martemyanov, Sergey M.

2011-01-01

The article is dedicated to investigation of the dielectric properties of oil shale. Investigations for samples prepared from shale mined at the deposit in Jilin Province in China were done. The temperature and frequency dependences of rock characteristics needed to calculate the processes of their thermal processing are investigated. Frequency dependences for the relative dielectric constant and dissipation factor of rock in the frequency range from 0,1 Hz to 1 MHz are investigated. The temperature dependences for rock resistance, dielectric capacitance and dissipation factor in the temperature range from 20 to 600°C are studied. Key words: shale, dielectric properties, relative dielectric constant, dissipation factor, temperature dependence, frequency dependence

Effects of structural characteristics on the productivity of shale gas wells: A case study on the Jiaoshiba Block in the Fuling shale gasfield, Sichuan Basin

Directory of Open Access Journals (Sweden)

Ming Hu

2018-03-01

Full Text Available For the sake of figuring out the influential mechanisms of structural characteristics on the productivity of shale gas wells, the structural characteristics of the Jiaoshiba Block in the Fuling shale gasfield, Sichuan Basin, were analyzed. Then, based on well test data of more than 190 horizontal wells, the effects of structures on shale gas well productivity were discussed systematically, and the main structural factors of different structural units in the Jiaoshiba Block that influence the productivity of shale gas wells were clarified. The following results were obtained. First, the structural units in the Jiaoshiba Block were obviously different in structural characteristics and their deformation strength is different. Second, the influence of structural characteristics on shale gas well productivity is directly manifested in gas-bearing property and fracturing effect. The stronger the structural deformation and the more developed the large faults and natural fractures, the more easily shale gas escapes and the poorer the gas bearing property will be, and vice versa. Third, The stronger the structural deformation, the more developed the fractures, the greater the burial depth and the higher the compressive stress of negative structures, the worse the fracturing effect will be, and vice versa. And fourth, Tectonics is the key factor controlling the difference of shale gas productivity between different structural units in the Jiaoshiba Block, but the main structural factors influencing the productivity are different in different structural units. Keywords: Sichuan Basin, Fuling shale gasfield, Jiaoshiba, Shale gas, Structural characteristics, Gas bearing property, Fracturing, Productivity

Market analysis of shale oil co-products. Summary report

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

This study examines the potential for separating, upgrading and marketing sodium mineral co-products together with shale oil production. The co-products investigated are soda ash and alumina which are derived from the minerals nahcolite and dawsonite. Five cases were selected to reflect the variance in mineral and shale oil content in the identified resource. In the five cases examined, oil content of the shale was varied from 20 to 30 gallons per ton. Two sizes of facilities were analyzed for each resource case to determine economies of scale between a 15,000 barrel per day demonstration unit and a 50,000 barrel per day full sized plant. Three separate pieces of analysis were conducted in this study: analysis of manufacturing costs for shale oil and co-products; projection of potential world markets for alumina, soda ash, and nahcolite; and determination of economic viability and market potential for shale co-products.

Compaction Characteristics of Igumale Shale | Iorliam | Global ...

African Journals Online (AJOL)

This paper reports the outcome of an investigation into the effect of different compactive energies on the compaction characteristics of Igumale shale, to ascertain its suitability as fill material in highway ... The study showed that Igumale shale is not suitable for use as base, subbase and filling materials in road construction.

Mechanical Characterization of Mancos Shale

Science.gov (United States)

Broome, S.; Ingraham, M. D.; Dewers, T. A.

2015-12-01

A series of tests on Mancos shale have been undertaken to determine the failure surface and to characterize anisotropy. This work supports additional studies which are being performed on the same block of shale; fracture toughness, permeability, and chemical analysis. Mechanical tests are being conducted after specimens were conditioned for at least two weeks at 70% constant relative humidity conditions. Specimens are tested under drained conditions, with the constant relative humidity condition maintained on the downstream side of the specimen. The upstream is sealed. Anisotropy is determined through testing specimens that have been cored parallel and perpendicular to the bedding plane. Preliminary results show that when loaded parallel to bedding the shale is roughly 50% weaker. Test are run under constant mean stress conditions when possible (excepting indirect tension, unconfined compression, and hydrostatic). Tests are run in hydrostatic compaction to the desired mean stress, then differential stress is applied axially in displacement control to failure. The constant mean stress condition is maintained by decreasing the confining pressure by half of the increase in the axial stress. Results will be compared to typical failure criteria to investigate the effectiveness of capturing the behavior of the shale with traditional failure theory. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2015-6107 A.

Sweet spots for hydraulic fracturing oil or gas production in underexplored shales using key performance indicators: Example of the Posidonia Shale formation in the Netherlands

NARCIS (Netherlands)

Heege, J.H. ter; Zijp, M.H.A.A.; Nelkamp, S.

2015-01-01

While extensive data and experiences are available for hydraulic fracturing and hydrocarbon production from shales in the U.S.A., such a record is lacking in many underexplored shale basins worldwide. As limited data is usually available in these basins, analysis of shale prospectivity and

Shale Gas Exploration and Development Progress in China and the Way Forward

Science.gov (United States)

Chen, Jianghua

2018-02-01

Shale gas exploration in China started late but is progressing very quickly with the strong support from Central Government. China has 21.8 tcm technically recoverable shale gas resources and 764.3 bcm proved shale gas reserve, mainly in marine facies in Sichuan basin. In 2016, overall shale gas production in China is around 7.9 bcm, while it is set to reach 10 bcm in 2017 and 30 bcm in 2020. BP is the only remaining IOC actor in shale gas exploration in China partnering with CNPC in 2 blocks in Sichuan basin. China is encouraging shale gas business both at Central level and at Provincial level through establishing development plan, continuation of subsidies and research funding. Engineering services for shale gas development and infrastructures are developing, while the overall cost and gas marketing conditions will be key factors for the success in shale gas industry.

Electric property evidences of carbonification of organic matters in marine shales and its geologic significance: A case study of the Lower Cambrian Qiongzhusi shale in the southern Sichuan Basin

Directory of Open Access Journals (Sweden)

Yuman Wang

2014-12-01

Full Text Available Searching for some reliable evidences that can verify the carbonification of organic matters in marine shales is a major scientific issue in selecting shale gas fairways in old strata. To this end, based on core, logging and testing data, the electric property of two organic-rich shale layers in the Lower Cambrian Qiongzhusi Fm. and the Lower Silurian Longmaxi Fm. in the southern Sichuan Basin was compared to examine the carbonification signs of organic matters in the Qiongzhusi shale and its influence on gas occurrence in the shales. The following conclusions were reached: (1 the electric property experiment shows that the Qiongzhusi shale in the study area has had carbonification of organic matters. The low resistivity of dry samples from this highly mature organic-rich shale and ultra-low resistivity on downhole logs can be used to directly judge the degree of organic matter carbonification and the quality of source rocks; (2 in the Changning area, the Qiongzhusi shale shows low resistivity of dry samples and low to ultra-low resistivity on logs, indicating that organic matters are seriously carbonized, while in the Weiyuan area, the Qiongzhusi shale shows a basically normal resistivity on log curves, indicating its degree of graphitization between the Longmaxi Fm. and Qiongzhusi Fm. in the Changning area; (3 shale with medium-to-high resistivity is remarkably better than that with ultra-low resistivity in terms of gas generation potential, matrix porosity and gas adsorption capacity; (4 industrial gas flow has been tested in the organic shales with medium-to-high resistivity in the Jianwei–Weiyuan–Tongnan area in the north, where the Qiongzhusi shale is a favorable shale gas exploration target.

Sweet spot identification and smart development -An integrated reservoir characterization study of a posidonia shale of a posidonia shale outcrop analogue

NARCIS (Netherlands)

Veen, J.H. ten; Verreussel, R.M.C.H.; Ventra, D.; Zijp, M.H.A.A.

2014-01-01

Shale gas reservoir stimulation procedures (e.g. hydraulic fracturing) require upfront prediction and planning that should be supported by a comprehensive reservoir characterization. Therefore, understanding shale depositional processes and associated vertical and lateral sedimentological

Dissolved methane in New York groundwater, 1999-2011

Science.gov (United States)

Kappel, William M.; Nystrom, Elizabeth A.

2012-01-01

New York State is underlain by numerous bedrock formations of Cambrian to Devonian age that produce natural gas and to a lesser extent oil. The first commercial gas well in the United States was dug in the early 1820s in Fredonia, south of Buffalo, New York, and produced methane from Devonian-age black shale. Methane naturally discharges to the land surface at some locations in New York. At Chestnut Ridge County Park in Erie County, just south of Buffalo, N.Y., several surface seeps of natural gas occur from Devonian black shale, including one behind a waterfall. Methane occurs locally in the groundwater of New York; as a result, it may be present in drinking-water wells, in the water produced from those wells, and in the associated water-supply systems (Eltschlager and others, 2001). The natural gas in low-permeability bedrock formations has not been accessible by traditional extraction techniques, which have been used to tap more permeable sandstone and carbonate bedrock reservoirs. However, newly developed techniques involving horizontal drilling and high-volume hydraulic fracturing have made it possible to extract previously inaccessible natural gas from low-permeability bedrock such as the Marcellus and Utica Shales. The use of hydraulic fracturing to release natural gas from these shale formations has raised concerns with water-well owners and water-resource managers across the Marcellus and Utica Shale region (West Virginia, Pennsylvania, New York and parts of several other adjoining States). Molofsky and others (2011) documented the widespread natural occurrence of methane in drinking-water wells in Susquehanna County, Pennsylvania. In the same county, Osborn and others (2011) identified elevated methane concentrations in selected drinking-water wells in the vicinity of Marcellus gas-development activities, although pre-development samples were not available for comparison. In order to manage water resources in areas of gas-well drilling and hydraulic

Assessment of industry needs for oil shale research and development

Energy Technology Data Exchange (ETDEWEB)

Hackworth, J.H.

1987-05-01

Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry's view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.

Oil shales and the nuclear process heat

International Nuclear Information System (INIS)

Scarpinella, C.A.

1974-01-01

Two of the primary energy sources most dited as alternatives to the traditional fossil fuels are oil shales and nuclear energy. Several proposed processes for the extraction and utilization of oil and gas from shale are given. Possible efficient ways in which nuclear heat may be used in these processes are discussed [pt

DEVONIAN RUGOSE CORALS FROM THE KARAKORUM MOUNTAINS (NORTHERN PAKISTAN

Directory of Open Access Journals (Sweden)

STEFAN SCHRÖDER

2004-11-01

Full Text Available The Karakorum Block is regarded as a microplate of "Gondwanan" origin and was part of the Cimmerian continent ("Mega Lhasa" which rifted away from the northern margin of Gondwana during the Late Palaeozoic/Early Mesozoic. From the Northern Karakorum Range (Yarkhun and Karambar River Valleys: structurally belonging to the Northern Sedimentary Belt an Upper Givetian to Lower Frasnian rugose coral fauna of the Shogram Formation is described. The fauna is dominated by cosmopolitan genera such as Hexagonaria, Disphyllum, Macgeea and the Temnophyllum/Spinophyllum group, generally showing a geographically wide distribution, although being absent from the Eastern Americas Realm in the Upper Givetian/Lower Frasnian. Therefore its components are of little use for biogeographical deductions at sub-realm level, and in explaining the relation between the Karakorum Range and other Cimmerian crustal blocks. A remarkable exception is the first record of the genus Pseudopexiphyllum outside of Turkey, indicating a connection to the western part of the Cimmerides. On species level, the coral fauna of the Shogram Formation is characterized by the development of a diverse and rather unique fauna including about 35 taxa, that differs from the faunas known from neighbouring crustal blocks. So far, faunistic links to the Central Iranian Microcontinent (Yazd-, and Tabas-Block, the northwest Iranian Plate (Elburz, Central Pamir, the Lhasa Block and Western Qiangtang are not clear, and although each of these fragments are believed to be closely connected they were apparently not in direct contact during the Devonian. However, the Karakorum fauna is remarkably close to one known from the Helmand Block in Afghanistan, showing a very similar generic composition that includes numerous morphologically closely related, although not identical species. Accordingly, the restricted faunal exchange led to the development of new taxa. Distribution of the new species of Spinophyllum

Validation Results for Core-Scale Oil Shale Pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Staten, Josh; Tiwari, Pankaj

2015-03-01

This report summarizes a study of oil shale pyrolysis at various scales and the subsequent development a model for in situ production of oil from oil shale. Oil shale from the Mahogany zone of the Green River formation was used in all experiments. Pyrolysis experiments were conducted at four scales, powdered samples (100 mesh) and core samples of 0.75”, 1” and 2.5” diameters. The batch, semibatch and continuous flow pyrolysis experiments were designed to study the effect of temperature (300°C to 500°C), heating rate (1°C/min to 10°C/min), pressure (ambient and 500 psig) and size of the sample on product formation. Comprehensive analyses were performed on reactants and products - liquid, gas and spent shale. These experimental studies were designed to understand the relevant coupled phenomena (reaction kinetics, heat transfer, mass transfer, thermodynamics) at multiple scales. A model for oil shale pyrolysis was developed in the COMSOL multiphysics platform. A general kinetic model was integrated with important physical and chemical phenomena that occur during pyrolysis. The secondary reactions of coking and cracking in the product phase were addressed. The multiscale experimental data generated and the models developed provide an understanding of the simultaneous effects of chemical kinetics, and heat and mass transfer on oil quality and yield. The comprehensive data collected in this study will help advance the move to large-scale in situ oil production from the pyrolysis of oil shale.

Shale Gas and Oil in Germany - Resources and Environmental Impacts

Science.gov (United States)

Ladage, Stefan; Blumenberg, Martin; Houben, Georg; Pfunt, Helena; Gestermann, Nicolai; Franke, Dieter; Erbacher, Jochen

2017-04-01

In light of the controversial debate on "unconventional" oil and gas resources and the environmental impacts of "fracking", the Federal Institute for Geosciences and Natural Resources (BGR) conducted a comprehensive resource assessment of shale gas and light tight oil in Germany and studied the potential environmental impacts of shale gas development and hydraulic fracturing from a geoscientific perspective. Here, we present our final results (BGR 2016), incorporating the majority of potential shale source rock formations in Germany. Besides shale gas, light tight oil has been assessed. According to our set of criteria - i.e. thermal maturity 0.6-1.2 %vitrinite reflectance (VR; oil) and >1.2 % VR (gas) respectively, organic carbon content > 2%, depth between 500/1000 m and 5000 m as well as a net thickness >20 m - seven potentially generative shale formations were indentified, the most important of them being the Lower Jurassic (Toarcian) Posidonia shale with both shale gas and tight oil potential. The North German basin is by far the most prolific basin. The resource assessment was carried out using a volumetric in-place approach. Variability inherent in the input parameters was accounted for using Monte-Carlo simulations. Technically recoverable resources (TRR) were estimated using recent, production-based recovery factors of North American shale plays and also employing Monte-Carlo simulations. In total, shale gas TRR range between 320 and 2030 bcm and tight oil TRR between 13 and 164 Mio. t in Germany. Tight oil potential is therefore considered minor, whereas the shale gas potential exceeds that of conventional resources by far. Furthermore an overview of numerical transport modelling approaches concerning environmental impacts of the hydraulic fracturing is given. These simulations are based on a representative lithostratigraphy model of the North-German basin, where major shale plays can be expected. Numerical hydrogeological modelling of frac fluid

Fluid flow from matrix to fractures in Early Jurassic shales

NARCIS (Netherlands)

Houben, M.E.; Hardebol, N.J.; Barnhoorn, A.; Boersma, Quinten; Carone, A.; Liu, Y.; de Winter, D.A.M.; Peach, C.J.; Drury, M.R.

2017-01-01

The potential of shale reservoirs for gas extraction is largely determined by the permeability of the rock. Typical pore diameters in shales range from the μm down to the nm scale. The permeability of shale reservoirs is a function of the interconnectivity between the pore space and the natural

Fluid flow from matrix to fractures in Early Jurassic shales

NARCIS (Netherlands)

Houben, M. E.; Hardebol, N.J.; Barnhoorn, A.; Boersma, Q.D.; Carone, A.; Liu, Y.; de Winter, D. A.M.; Peach, C. J.; Drury, M. R.

2017-01-01

The potential of shale reservoirs for gas extraction is largely determined by the permeability of the rock. Typical pore diameters in shales range from the μm down to the nm scale. The permeability of shale reservoirs is a function of the interconnectivity between the pore space and the natural

Fingerprinting Marcellus Shale waste products from Pb isotope and trace metal perspectives

International Nuclear Information System (INIS)

Johnson, Jason D.; Graney, Joseph R.

2015-01-01

Highlights: • Dry drilled, uncontaminated cuttings from Marcellus Shale and surrounding units. • Unoxidized and oxidized samples leached short and long term with H 2 O or dilute HCl. • Pb isotope ratios have distinctly different values from Marcellus Shale samples. • Mo and other trace metals can be used as Marcellus Shale environmental tracers. • Marcellus Shale leachate concentrations can exceed EPA contaminant screening levels. - Abstract: Drill cuttings generated during unconventional natural gas extraction from the Marcellus Shale, Appalachian Basin, U.S.A., generally contain a very large component of organic-rich black shale because of extensive lateral drilling into this target unit. In this study, element concentrations and Pb isotope ratios obtained from leached drill cuttings spanning 600 m of stratigraphic section were used to assess the potential for short and long term environmental impacts from Marcellus Shale waste materials, in comparison with material from surrounding formations. Leachates of the units above, below and within the Marcellus Shale yielded Cl/Br ratios of 100–150, similar to produced water values. Leachates from oxidized and unoxidized drill cuttings from the Marcellus Shale contain distinct suites of elevated trace metal concentrations, including Cd, Cu, Mo, Ni, Sb, U, V and Zn. The most elevated Mo, Ni, Sb, U, and V concentrations are found in leachates from the lower portion of the Marcellus Shale, the section typically exploited for natural gas production. In addition, lower 207 Pb/ 206 Pb ratios within the lower Marcellus Shale (0.661–0.733) provide a distinctive fingerprint from formations above (0.822–0.846) and below (0.796–0.810), reflecting 206 Pb produced as a result of in situ 238 U decay within this organic rich black shale. Trace metal concentrations from the Marcellus Shale leachates are similar to total metal concentrations from other black shales. These metal concentrations can exceed screening

Application of binomial-edited CPMG to shale characterization.

Science.gov (United States)

Washburn, Kathryn E; Birdwell, Justin E

2014-09-01

Unconventional shale resources may contain a significant amount of hydrogen in organic solids such as kerogen, but it is not possible to directly detect these solids with many NMR systems. Binomial-edited pulse sequences capitalize on magnetization transfer between solids, semi-solids, and liquids to provide an indirect method of detecting solid organic materials in shales. When the organic solids can be directly measured, binomial-editing helps distinguish between different phases. We applied a binomial-edited CPMG pulse sequence to a range of natural and experimentally-altered shale samples. The most substantial signal loss is seen in shales rich in organic solids while fluids associated with inorganic pores seem essentially unaffected. This suggests that binomial-editing is a potential method for determining fluid locations, solid organic content, and kerogen-bitumen discrimination. Copyright © 2014 Elsevier Inc. All rights reserved.

Trace elements in oil shale. Progress report, 1976--1979

Energy Technology Data Exchange (ETDEWEB)

Chappell, W.R.

1979-01-01

The overall objective of the program is to evaluate the environmental and health consequences of the release of toxic trace elements (As, B, F, Mo, Se) by shale oil production and use. Some of the particularly significant results are: The baseline geochemical survey shows that stable trace elements maps can be constructed for numerous elements and that the trends observed are related to geologic and climatic factors. Shale retorted by above-ground processes tends to be very homogeneous (both in space and in time) in trace element content. This implies that the number of analytical determinations required of processed shales is not large. Leachate studies show that significant amounts of B, F, And Mo are released from retorted shales and while B and Mo are rapidly flushed out, F is not. On the other hand, As, Se, and most other trace elements ae not present in significant quantities. Significant amounts of F and B are also found in leachates of raw shales. Very large concentrations of reduced sulfur species are found in leachates of processed shale. Upon oxidation a drastic lowering in pH is observed. Preliminary data indicates that this oxidation is catalyzed by bacteria. Very high levels of B and Mo are taken up in some plants growing on processed shale with and without soil cover. These amounts depend upon the process and various site specific characteristics. In general, the amounts taken up decrease with increasing soil cover. On the other hand, we have not observed significant uptake of As, Se, and F into plants. There is a tendency for some trace elements to associate with specific organic fractions, indicating that organic chelation or complexation may play an important role. In particular, most of the Cd, Se, and Cr in shale oil is associated with the organic fraction containing most of the nitrogen-containing compounds.

Multiphysical Testing of Soils and Shales

CERN Document Server

Ferrari, Alessio

2013-01-01

Significant advancements in the experimental analysis of soils and shales have been achieved during the last few decades. Outstanding progress in the field has led to the theoretical development of geomechanical theories and important engineering applications. This book provides the reader with an overview of recent advances in a variety of advanced experimental techniques and results for the analysis of the behaviour of geomaterials under multiphysical testing conditions. Modern trends in experimental geomechanics for soils and shales are discussed, including testing materials in variably saturated conditions, non-isothermal experiments, micro-scale investigations and image analysis techniques. Six theme papers from leading researchers in experimental geomechanics are also included. This book is intended for postgraduate students, researchers and practitioners in fields where multiphysical testing of soils and shales plays a fundamental role, such as unsaturated soil and rock mechanics, petroleum engineering...

Process for recovering oil from shale, etc

Energy Technology Data Exchange (ETDEWEB)

1920-08-20

A process is described for recovering oil from oil-shale and the like, by the direct action of the hot gases obtained by burning the carbonized shale residue. It is immediately carried out in separate adjacent chambers, through which the feed goes from one to the other intermittently, from the upper to the lower.

Organic geochemistry: Effects of organic components of shales on adsorption: Progress report

International Nuclear Information System (INIS)

Ho, P.C.

1988-11-01

The Sedimentary Rock Program at the Oak Ridge National Laboratory is investigating shale to determine its potential suitability as a host rock for the disposal of high-level radioactive wastes (HLW). The selected shales are Upper Dowelltown, Pierre, Green River Formation, and two Conasauga (Nolichucky and Pumpkin Valley) Shales, which represent mineralogical and compositional extremes of shales in the United States. According to mineralogical studies, the first three shales contain 5 to 13 wt % of organic matter, and the two Conasauga Shales only contain trace amounts (2 wt %) of organic matter. Soxhlet extraction with chloroform and a mixture of chloroform and methanol can remove 0.07 to 5.9 wt % of the total organic matter from these shales. Preliminary analysis if these organic extracts reveals the existence of organic carboxylic acids and hydrocarbons in these samples. Adsorption of elements such as Cs(I), Sr(II) and Tc(VII) on the organic-extracted Upper Dowelltown, Pierre, green River Formation and Pumpkin Valley Shales in synthetic groundwaters (simulating groundwaters in the Conasauga Shales) and in 0.03-M NaHCO 3 solution indicates interaction between each of the three elements and the organic-extractable bitumen. 28 refs., 8 figs., 10 tabs

Production of portland cement using Moroccan oil shale and comparative study between conventional cement plant and cement plant using oil shale

International Nuclear Information System (INIS)

Doumbouya, M.; Kacemi, K.E.; Kitane, S.

2012-01-01

Like the use of coal ash from power plants as an addition to cement, oil shale are used for cement production on an industrial scale in Estonia, China, USA and Germany. Oil shale can be utilized in manufacturing the cement. In addition to the utilization of these by-products after combustion, it can also reduce the required temperature for the clinkering reactions during the production of Portland clinker. We performed a study on the Moroccan oil shale to maximize the use of oil shale ash in the manufacturing of Portland cement. We found that Moroccan oil shale ash can be used up to 30% with 70% Portland clinker without altering its principle properties. The corresponding temperature required to generate the required liquid for the clinkering reactions as well as the essential ingredients for clinker was found to be around 850 to 1000 deg. C. The operating temperatures for this optimized blend ratio were found to 1000 deg. C. The resulting Portland clinker from this ratio will need further testing in accordance with international standards for Portland cement to examine properties like strength and setting time. (author)

Attenuation of Chemical Reactivity of Shale Matrixes following Scale Precipitation

Science.gov (United States)

Li, Q.; Jew, A. D.; Kohli, A. H.; Alalli, G.; Kiss, A. M.; Kovscek, A. R.; Zoback, M. D.; Brown, G. E.; Maher, K.; Bargar, J.

2017-12-01

Introduction of fracture fluids into shales initiates a myriad of fluid-rock reactions that can strongly influence migration of fluid and hydrocarbon through shale/fracture interfaces. Due to the extremely low permeability of shale matrixes, studies on chemical reactivity of shales have mostly focused on shale surfaces. Shale-fluid interactions inside within shale matrixes have not been examined, yet the matrix is the primary conduit through which hydrocarbons and potential contaminants are transmitted. To characterize changes in matrix mineralogy, porosity, diffusivity, and permeability during hydraulic stimulation, we reacted Marcellus (high clay and low carbonate) and Eagle Ford (low clay and high carbonate) shale cores with fracture fluids for 3 weeks at elevated pressure and temperature (80 oC, and 77 bars). In the carbonate-poor Marcellus system, fluid pH increased from 2 to 4, and secondary Fe(OH)3 precipitates were observed in the fluid. Sulfur X-ray fluorescence maps show that fluids had saturated and reacted with the entire 1-cm-diameter core. In the carbonate-rich Eagle Ford system, pH increased from 2 to 6 due to calcite dissolution. When additional Ba2+ and SO42- were present (log10(Q/K)=1.3), extensive barite precipitation was observed in the matrix of the Eagle Ford core (and on the surface). Barite precipitation was also observed on the surface of the Marcellus core, although to a lesser extent. In the Marcellus system, the presence of barite scale attenuated diffusivity in the matrix, as demonstrated by sharply reduced Fe leaching and much less sulfide oxidation. Systematic studies in homogeneous solution show that barite scale precipitation rates are highly sensitive to pH, salinity, and the presence of organic compounds. These findings imply that chemical reactions are not confined to shale/fluid interfaces but can penetrate into shale matrices, and that barite scale formation can clog diffusion pathways for both fluid and hydrocarbon.

Investigating the Potential Impacts of Energy Production in the Marcellus Shale Region Using the Shale Network Database and CUAHSI-Supported Data Tools

Science.gov (United States)

Brazil, L.

2017-12-01

The Shale Network's extensive database of water quality observations enables educational experiences about the potential impacts of resource extraction with real data. Through open source tools that are developed and maintained by the Consortium of Universities for the Advancement of Hydrologic Science, Inc. (CUAHSI), researchers, educators, and citizens can access and analyze the very same data that the Shale Network team has used in peer-reviewed publications about the potential impacts of hydraulic fracturing on water. The development of the Shale Network database has been made possible through collection efforts led by an academic team and involving numerous individuals from government agencies, citizen science organizations, and private industry. Thus far, CUAHSI-supported data tools have been used to engage high school students, university undergraduate and graduate students, as well as citizens so that all can discover how energy production impacts the Marcellus Shale region, which includes Pennsylvania and other nearby states. This presentation will describe these data tools, how the Shale Network has used them in developing educational material, and the resources available to learn more.

Application of high-precision 3D seismic technology to shale gas exploration: A case study of the large Jiaoshiba shale gas field in the Sichuan Basin

Directory of Open Access Journals (Sweden)

Zuqing Chen

2016-03-01

Full Text Available The accumulation pattern of the marine shale gas in South China is different from that in North America. The former has generally thin reservoirs and complex preservation conditions, so it is difficult to make a fine description of the structural features of shale formations and to reflect accurately the distribution pattern of high-quality shale by using the conventional 2D and 3D seismic exploration technology, which has an adverse effect on the successful deployment of horizontal wells. In view of this, high-precision 3D seismic prospecting focusing on lithological survey was implemented to make an accurate description of the distribution of shale gas sweet spots so that commercial shale gas production can be obtained. Therefore, due to the complex seismic geological condition of Jiaoshiba area in Fuling, SE Sichuan Basin, the observation system of high-precision 3D seismic acquisition should have such features as wide-azimuth angles, small trace intervals, high folds, uniform vertical and horizontal coverage and long spread to meet the needs of the shale gas exploration in terms of structural interpretation, lithological interpretation and fracture prediction. Based on this idea, the first implemented high-precision 3D seismic exploration project in Jiaoshiba area played an important role in the discovery of the large Jiaoshiba shale gas field. Considering that the high-quality marine shale in the Sichuan Basin shows the characteristics of multi-layer development from the Silurian system to the Cambrian system, the strategy of shale gas stereoscopic exploration should be implemented to fully obtain the oil and gas information of the shallow, medium and deep strata from the high-precision 3D seismic data, and ultimately to expand the prospecting achievements in an all-round way to balance the high upstream exploration cost, and to continue to push the efficient shale gas exploration and development process in China.

Traces in the dark: sedimentary processes and facies gradients in the upper shale member of the Upper Devonian-Lower Mississippian Bakken Formation, Williston Basin, North Dakota, U.S.A.

Science.gov (United States)

Egenhoff, Sven O.; Fishman, Neil S.

2013-01-01

Black, organic-rich rocks of the upper shale member of the Upper Devonian–Lower Mississippian Bakken Formation, a world-class petroleum source rock in the Williston Basin of the United States and Canada, contain a diverse suite of mudstone lithofacies that were deposited in distinct facies belts. The succession consists of three discrete facies associations (FAs). These comprise: 1) siliceous mudstones; 2) quartz- and carbonate-bearing, laminated mudstones; and 3) macrofossil-debris-bearing massive mudstones. These FAs were deposited in three facies belts that reflect proximal to distal relationships in this mudstone system. The macrofossil-debris-bearing massive mudstones (FA 3) occur in the proximal facies belt and contain erosion surfaces, some with overlying conodont and phosphate–lithoclast lag deposits, mudstones with abundant millimeter-scale siltstone laminae showing irregular lateral thickness changes, and shell debris. In the medial facies belt, quartz- and carbonate-bearing, laminated mudstones dominate, exhibiting sub-millimeter-thick siltstone layers with variable lateral thicknesses and localized mudstone ripples. In the distal siliceous mudstone facies belt, radiolarites, radiolarian-bearing mudstones, and quartz- and carbonate-bearing, laminated mudstones dominate. Overall, total organic carbon (TOC) contents range between about 3 and 10 wt %, with a general proximal to distal decrease in TOC content. Abundant evidence of bioturbation exists in all FAs, and the lithological and TOC variations are paralleled by changes in burrowing style and trace-fossil abundance. While two horizontal traces and two types of fecal strings are recognized in the proximal facies belt, only a single horizontal trace fossil and one type of fecal string characterize mudstones in the distal facies belt. Radiolarites intercalated into the most distal mudstones are devoid of traces and fecal strings. Bedload transport processes, likely caused by storm-induced turbidity

Joint DoD/DoE Shale Oil Project. Volume 3. Testing of Refined Shale Oil Fuels.

Science.gov (United States)

1983-12-01

10-9. GROWTH RATINGS OF CLADOSPORIUM RESINAE AT VARIOUS INCUBATION STAGES ......................... 10-25 S 0 xv - LIST OF TABLES (Continued) TABLE 10...test_nC are sho’ T, in Trbl]e .3 d :: ab ffr stead..--staoe zerfrrmance was noted wcrh the snale fel. Wh’le a ..6 :o:n: = in Scecifiz Fuel Consumption...both shale DFM and shale JP-5 support heavy growth of Cladosporium resinae . Short-term engine performance tests were conducted on two gas turbine

Conodont-bearing formations of Devonian and Lower Carboniferous age in northern León and Palencia (Spain)

NARCIS (Netherlands)

Adrichem Boogaert, van H.A.

1965-01-01

Conodonts have been extracted from calcareous units of the Devonian and Lower Carboniferous sequence from 3 areas in the S. part of the Cantabrian Mountains. There can be distinguished Emsian, Givetian, Frasnian, Famennian and Viséan faunas.

A Large Trace Fossil in Nodular Limestones (Lower Devonian, Czech Republic): Sedimentological Consequences, Ethology and Taphonomy

Czech Academy of Sciences Publication Activity Database

Mikuláš, Radek; Hladil, Jindřich

2015-01-01

Roč. 22, č. 2 (2015), s. 69-76 ISSN 1042-0940 R&D Projects: GA ČR GA14-18183S Institutional support: RVO:67985831 Keywords : bioturbation * Fodinichnia * carbonate * nodules * Devonian * Czech Republic Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.935, year: 2015

Nitrogen fixation by legumes in retorted shale

Energy Technology Data Exchange (ETDEWEB)

Hersman, L E; Molitoris, E; Klein, D A

1981-01-01

A study was made to determine whether retorted shale additions would significantly affect symbiotic N/sub 2/ fixation. Results indicate that small additions of the shale may stimulate plant growth but with higher concentrations plants are stressed, resulting in a decreased biomass and a compensatory effect of an increased number of nodules and N/sub 2/ fixation potential. (JMT)

Analysis of the environmental control technology for oil shale development

Energy Technology Data Exchange (ETDEWEB)

de Nevers, N.; Eckhoff, D.; Swanson, S.; Glenne, B.; Wagner, F.

1978-02-01

The environmental control technology proposed in the various oil shale projects which are under development are examined. The technologies for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the processed shale were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. There are no published national standards against which to judge the stabilization and vegetation of the processed shale. However, based on the goal of producing an environmentally and aesthetically acceptable finished processed shale pile, it seems probable that this can be accomplished. It is concluded that the environmental control technology is available to meet all current legal requirements. This was not the case before Colorado changed their applicable Air Pollution regulations in August of 1977; the previous ones for the oil shale region were sufficiently stringent to have caused a problem for the current stage of oil shale development. Similarly, the federal air-quality, non-deterioration regulations could be interpreted in the future in ways which would be difficult for the oil shale industry to comply with. The Utah water-quality, non-deterioration regulations could also be a problem. Thus, the only specific regulations which may be a problem are the non-deterioration parts of air and water quality regulations. The unresolved areas of environmental concern with oil shale processing are mostly for the problems not covered by existing environmental law, e.g., trace metals, polynuclear organics, ground water-quality changes, etc. These may be problems, but no evidence is yet available that these problems will prevent the successful commercialization of oil shale production.

Life cycle water consumption for shale gas and conventional natural gas.

Science.gov (United States)

Clark, Corrie E; Horner, Robert M; Harto, Christopher B

2013-10-15

Shale gas production represents a large potential source of natural gas for the nation. The scale and rapid growth in shale gas development underscore the need to better understand its environmental implications, including water consumption. This study estimates the water consumed over the life cycle of conventional and shale gas production, accounting for the different stages of production and for flowback water reuse (in the case of shale gas). This study finds that shale gas consumes more water over its life cycle (13-37 L/GJ) than conventional natural gas consumes (9.3-9.6 L/GJ). However, when used as a transportation fuel, shale gas consumes significantly less water than other transportation fuels. When used for electricity generation, the combustion of shale gas adds incrementally to the overall water consumption compared to conventional natural gas. The impact of fuel production, however, is small relative to that of power plant operations. The type of power plant where the natural gas is utilized is far more important than the source of the natural gas.

Producing electricity from Israel oil shale with PFBC technology

International Nuclear Information System (INIS)

Grinberg, A.; Keren, M.; Podshivalov, V.; Anderson, J.

2000-01-01

Results of Israeli oil shale combustion at atmospheric pressure in the AFBC commercial boiler manufactured by Foster Wheeler Energia Oy (Finland) and in the pressurized test facility of ABB Carbon AB (Finspong, Sweden) confirm suitability of fluidized-bed technologies in case of oil shale. The results approve possibility to use the PFBC technology in case of oil shale after solving of some problems connected with great amounts of fine fly ash. (author)

Systematics of some Lower and Middle Devonian spiriferid brachiopods from Gaspe with a revision of the superfamily Delthyridoidea

DEFF Research Database (Denmark)

Bizzarro, Martin; Lespérance, P.J.

1999-01-01

new species aye described: Howellella (Howellella) forillonensis, Brachyspirifer (Brachyspirifer) briseboisi, Paraspirifer desbiensi, Brevispirifer florentinus, and B. quebecensis, The occurrence of Brevispirifer species with Middle Devonian chonetaceans confirms the presence of marine Eifelian strata...

Some problems of oil shale retorting in Estonia

International Nuclear Information System (INIS)

Oepik, I.

1994-01-01

Oil shale in Estonia will be competitive in the long term as a primary resource for power generating. The price of energy of Estonian oil shale is at present approximately 4 times lower than of coal. The price of electricity is anticipated to grow up to EEK 1.0/kWh in year 2020. The electricity price EEK 0.2/kWh at present in Estonia does not include capital costs needed for refurbishing of Estonian oil-shale-consuming power stations between the years 2000-2010. While all the prices and calculations of the enterprise are presented with no inflation adjustment, the other operation costs of oil shale retorting are anticipated for the prognosed period to remain at the present level: power consumption kWh 280/t crude oils and other operation costs (excluding labour, raw material and power consumption) EEK 100/t of oil

Stratigraphy, structure, and lithofacies relationships of Devonian through Permian sedimentary rocks: Paradox Basin and adjacent areas - southeastern Utah. Technical report

International Nuclear Information System (INIS)

McCleary, J.; Rogers, T.; Ely, R.

1983-08-01

Geophysical well log analysis, literature review, and field work were conducted to develop isopach, structure contour, outcrop, and facies maps and cross sections for the Devonian through Permian strata of a 14,586-km 2 (5632-square-mile) area in southeastern Utah. The study area includes part of the Paradox Basin, the salt deposits of which are of interest in siting studies for a nuclear waste repository. For this reason hydrologic models of this area are needed. This study, part of which included the development of a three-dimensional stratigraphic computer model utilizing Geographic Information System software, can serve as a base for hydrologic or other models for this area. Within and adjacent to the study area, 730 wells were screened to select the 191 wells analyzed for the study. It was found that the Elbert through Molas formations did not exhibit noticeable facies changes within the study area. The Pinkerton Trail Formation exhibits moderate changes: anhydrite and shale become somewhat more abundant toward the northeast. Facies changes in the Paradox Formation are more dramatic. Thick saline facies deposits are present in the northeast, grading to thinner anhydrite and then to carbonate facies in the south and west. The lithology of the Honaker Trail Formation appears to be fairly uniform throughout the area. Facies changes in the Cutler Group are numerous and sometimes dramatic, and generally correspond to the named formations of the group. Other factors that could affect groundwater flow, such as stratigraphic cover of fine-grained rocks, area of formation outcrops, and fracturing and faulting are discussed and delineated on maps

Origin of Scottish oil shales

Energy Technology Data Exchange (ETDEWEB)

Conacher, H R.J.

1916-12-01

Oil shales contain two distinct types of organic material, one is comparable to the woody material in coal and the other consists of yellow bodies. When distilled, the latter yields the liquid product typical of oil shale, whereas the woody material produces large amounts of ammonia. The yellow bodies have been described by various investigators as fossil algae, spores, or dried-up globules of petroleum. In this study it was concluded that the yellow bodies were fragments of resins set free by the decay and oxidation of the vegetable matter with which they were originally associated.

Discussion on the exploration & development prospect of shale gas in the Sichuan Basin

Directory of Open Access Journals (Sweden)

Dazhong Dong

2015-01-01

Full Text Available The Sichuan Basin, a hotspot and one of the most successful areas for shale gas exploration and development, can largely reflect and have a big say in the future prospect of shale gas in China. Through an overall review on the progress in shale gas exploration and development in the Sichuan Basin, we obtained the following findings: (1 the Sichuan Basin has experienced the marine and terrestrial depositional evolution, resulting in the deposition of three types of organic-matter-rich shales (i.e. marine, transitional, and terrestrial, and the occurrence of six sets of favorable shale gas enrichment strata (i.e. the Sinian Doushantuo Fm, the Cambrian Qiongzhusi Fm, the Ordovician Wufeng–Silurian Longmaxi Fm, the Permian Longtan Fm, the Triassic Xujiahe Fm, and the Jurassic Zhiliujing Fm; (2 the five key elements for shale gas accumulation in the Wufeng-Longmaxi Fm are deep-water shelf facies, greater thickness of organic-rich shales, moderate thermal evolution, abundant structural fractures, reservoir overpressure; and (3 the exploration and development of shale gas in this basin still confronts two major challenges, namely, uncertain sweet spots and potential prospect of shale gas, and the immature technologies in the development of shale gas resources at a depth of more than 3500 m. In conclusion, shale gas has been discovered in the Jurassic, Triassic and Cambrian, and preliminary industrial-scale gas has been produced in the Ordovician-Silurian Fm in the Sichuan Basin, indicating a promising prospect there; commercial shale gas can be produced there with an estimated annual gas output of 30–60 billion m3; and shale gas exploration and production experiences in this basin will provide valuable theoretical and technical support for commercial shale gas development in China.

Early Devonian polygnathids of Northeast Asia and correlation of Pragian/Emsian strata of the marginal seas of Angarida

Czech Academy of Sciences Publication Activity Database

Baranov, V.; Slavík, Ladislav; Blodgett, R. B.

2014-01-01

Roč. 89, č. 3 (2014), s. 645-678 ISSN 1214-1119 Institutional support: RVO:67985831 Keywords : Early Devonian * Pragian/Emsian strata * Angarida Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.515, year: 2014

Shale gas - uncertain destiny?

International Nuclear Information System (INIS)

Signoret, Stephane

2013-01-01

This article outlines that, even if it would be allowed, the exploitation of shale gas in France would need ten years to start, and no one can say what would be our needs then and what would be the situation of the gas market at that time. Even if the government decided to forbid hydraulic fracturing, there could be some opportunity for experimentation with a search for alternative technology. The article notices that risks associated with hydraulic fracturing and extraction of non conventional hydrocarbons, i.e. water pollution and consumption and land use, are variously perceived in different European countries (Germany, Romania, Poland) where important American actors are present (Chevron, Exxon) to exploit shale gases. In the USA, the economic profitability seems in fact to rapidly decrease

Developments in production of synthetic fuels out of Estonian shale

Energy Technology Data Exchange (ETDEWEB)

Aarna, Indrek

2010-09-15

Estonia is still the world leader in utilization of oil shale. Enefit has cooperated with Outotec to develop a new generation of solid heat carrier technology - Enefit280, which is more efficient, environmentally friendlier and has higher unit capacity. Breakeven price of oil produced in Enefit280 process is competitive with conventional oils. The new technology has advantages that allow easy adaptation to other oil shales around the world. Hydrotreated shale oil liquids have similar properties to crude oil cuts. Design for a shale oil hydrotreater unit can use process concepts, hardware components, and catalysts commercially proven in petroleum refining services.

Correlation of Early Devonian (Lochkovian-early Pragian) conodont faunas of the South Urals (Russia)

Czech Academy of Sciences Publication Activity Database

Mavrinskaya, T.; Slavík, Ladislav

2013-01-01

Roč. 88, č. 3 (2013), s. 283-296 ISSN 1214-1119 Grant - others:Rada Programu interní podpory projektů mezinárodní spolupráce AV ČR(CZ) M100131201 Institutional support: RVO:67985831 Keywords : South Urals, West Zilair Zone, Lower Devonian, global conodont correlation, Lochkovian, Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.495, year: 2013

A rich ichnofossil assemblage from the Frasnian (Upper Devonian) deposits at Andoma Hill, Onega Lake, Russia

Czech Academy of Sciences Publication Activity Database

Mikuláš, Radek; Meškis, S.; Ivanov, A.; Lukševičs, E.; Zupinš, I.; Stinkulis, G.

2013-01-01

Roč. 88, č. 2 (2013), s. 389-400 ISSN 1214-1119 Institutional research plan: CEZ:AV0Z30130516 Institutional support: RVO:67985831 Keywords : ichnology * East European Platform * Main Devonian field * Old Red Sandstone facies Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.495, year: 2013

Devonian trilobites of the southern Cantabrian Mountains (northern Spain) with a systematic description of the Asteropyginae

NARCIS (Netherlands)

Smeenk, Z.

1983-01-01

This paper shows the results of a research into the Devonian trilobites of the southern Cantabrian Mountains. The systematics of the most common group, the subfamily of the Asteropyginae, forms the major part of this work. More than 50 species, belonging to sixteen (sub)genera are distinguished;

Concentration mechanisms of uranium in the mineralized fractures of the Lower Devonian of the Belgian Ardennes - The case of the Oizy area

International Nuclear Information System (INIS)

Charlet, J.M.; Doremus, P.; Quinif, Y.

1987-01-01

During a reconnaissance survey for uranium in the Belgian Paleozoic several anomalies or U occurrences have been discovered in the Lower Devonian by a car-borne radiometric survey. These anomalies appear in relation with mobilization and reconcentration processes at the boundary of redox fronts or following alteration fronts in the detrital series of the Lower Devonian. This paper describes the Oizy anomaly which occurs in a fracturated zone of the Gedinnian formations of the Ardenne Anticline and puts it back in the general context of the U concentrations of the Lower Devonian of the Belgian Ardennes. After a lithostratigraphic, structural and radiometric study of the quarry where the U concentrations occur, a laboratory study of the surrounding rocks has been performed by various techniques (γ- and α-spectrometry, X-ray diffraction, autoradiography and low-level counting technique, analytical chemistry). One can conclude that the mineralized fractures of Oizy are due to a downward remobilization of U by subsurface processes during post-Hercynian periods. 26 refs.; 11 figs.; 1 plate; 2 tabs

Evaluation of excavation experience: Pierre shale. Final report

International Nuclear Information System (INIS)

Abel, J.F. Jr.; Gentry, D.W.

1975-01-01

Pierre shale and its stratigraphic equivalents represent a potentially favorable geologic environment for underground storage of hazardous waste products. These rock formations cover great areal and vertical extents, and represent some of the least permeable rock formations within the continental United States. There are, however, several engineering problems associated with constructing underground openings in Pierre shale. This formation is relatively weak and tends to deteriorate rather rapidly if not protected from the mine environment. It will be necessary to place all underground openings below the surficially weathered upper 50 to 70 feet of Pierre shale which contains groundwater moving on fracture permeability. The optimum site for disposal of hazardous waste in Pierre shale, or its stratigraphic equivalents, would be a seismically stable platform bounded on all sides by faults. The optimum size of individual openings would be the minimum necessary for access, storage, and retrieval of waste components. Underground excavations in Pierre shale must be made with care, must be of limited dimensions, must be widely spaced, must be protected from prolonged contact with the mine environment, must be supported immediately after excavation, and must be sited to avoid areas of faulting and(or) intense jointing. Underground openings constructed with boring machines and supported with wet shotcrete are recommended

Method of distillation of sulfurous bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Hallback, A J.S.; Bergh, S V

1918-04-22

A method of distillation of sulfur-containing bituminous shales is characterized by passing the hot sulfur-containing and oil-containing gases and vapors formed during the distillation through burned shale containing iron oxide, so that when these gases and vapors are thereafter cooled they will be, as far as possible, free from sulfur compounds. The patent contains six more claims.

Energy (in)security in Poland the case of shale gas

International Nuclear Information System (INIS)

Johnson, Corey; Boersma, Tim

2013-01-01

The large scale extraction of natural gas from shale rock layers in North America using hydraulic fracturing, or “fracking”, has prompted geologists, economists and politicians in various parts of the world to ask whether there are new reserves of this precious resource to be found under their soils. It has also raised a host of questions about the potential environmental impacts of extracting it. Drawing on research on both sides of the Atlantic, this paper assesses the most pressing issues for research and policy makers related to shale gas extraction. The paper first provides a survey of environmental and economic issues related to shale gas. It then turns to a case study of Poland, whose policy makers have been among the most fervent proponents of shale gas development in the European Union. We examine the status of shale gas extraction in that country and what the barriers are to overcome before commercial extraction can in fact take place, if at all. - Highlights: ► We examine geologic, economic, environmental and political issues of shale gas. ► Poland is used to assess prospects for shale gas development in Europe. ► Debate in Poland has largely been framed as an energy security issue. ► A number of significant hurdles may prevent large scale development there.

Cracking mechanism of shale cracks during fracturing

Science.gov (United States)

Zhao, X. J.; Zhan, Q.; Fan, H.; Zhao, H. B.; An, F. J.

2018-06-01

In this paper, we set up a model for calculating the shale fracture pressure on the basis of Huang’s model by the theory of elastic-plastic mechanics, rock mechanics and the application of the maximum tensile stress criterion, which takes into account such factors as the crustal stress field, chemical field, temperature field, tectonic stress field, the porosity of shale and seepage of drilling fluid and so on. Combined with the experimental data of field fracturing and the experimental results of three axis compression of shale core with different water contents, the results show that the error between the present study and the measured value is 3.85%, so the present study can provide technical support for drilling engineering.

Economic Impacts Analysis of Shale Gas Investment in China

Science.gov (United States)

Han, Shangfeng; Zhang, Baosheng; Wang, Xuecheng

2018-01-01

Chinese government has announced an ambitious shale gas extraction plan, which requires significant investment. This has the potential to draw investment from other areas and may affect the whole China’s economy. There is few study to date has quantified these shale gas investment’s effects on Chinese economy. The aim of this paper is to quantify the economic effect and figures out whether shale gas investment in China is a good choice or not. Input-output analysis has been utilized in this study to estimate the economic impacts in four different Chinese regions. Our findings show that shale gas investment will result in approximately 868, 427, 115 and 42 Billion RMB economic impacts in Sichuan, Chongqing, Inner Mongolia and Guizhou, respectively. The total economic impact is only around 1453 Billion RMB, which is not significant compared to the economic impact of coalbed methane investment. Considering the potential risks of environmental issues, we suggest that it may be a better strategy for the government, at least in the current situation, to slow down shale gas development investment.

Structural Evolution and Mobile Shale Deformation in the Eastern Niger Delta

International Nuclear Information System (INIS)

Wiener, R. W.; Aikhionbare, D. O. L.

2002-01-01

Regional cross-sections and restorations of the eastern delta constructed from 2D and 3D seismic data show the structural evolution of paired extensional contractional belts and the kinematic and geometric evolution of mobile shale. The delta consists of an updip extensional belt and downdip zones of transitional and contractional deformation linked by a regional detachment. The extensional belt is characterized by zones of N-dipping (counterregional) and S-dipping (regional) normal faults.In the regional fault trend, sediment accommodation space is created largely by lateral movement of mobile substrate due to sediment loading and gravity. The transitional belt is characterized by low relief, shale-cored detachment folds and normal faults. The contractional belt consists of 2 parts, the high relief shale-cored detachment fold belt (mobile shale) and the fold/thrust belt: In the mobile shale belt, anticlines are generally symmetric and characterized by parallel-folded cover and highly variable thickness in the underlying ductile shale zone.Palinspastic restoration of the mobile shale by area balance shows a high degree of lateral and vertical mobility. Isostatic restoration of the depositional wedge that is the precursor to the mobile shale suggests lateral movement of 10s of kms from the extensional to the contractional domain. The fold and thrust belt is characterized by a train of asymmetric fault-related folds. The zone of ductile substrate is thin in this area, which may account for the change in structural style from high relief detachment folds in the mobile shale belt to a more classic fold/thrust belt style to the south

PALEOMAGNETISM OF SILURIAN AND DEVONIAN VOLCANICS FROM THE CHINGIZ ISLAND ARC, KAZAKHSTAN, AND ITS BEARING ON TECTONIC EVOLUTION OF THE URAL-MONGOL BELT

Directory of Open Access Journals (Sweden)

Natalia M. Levashova

2011-01-01

Full Text Available The tectonic and paleogeographic evolution of the Ural-Mongol belt between the cratons of Baltica, Siberia, and Tarim is the key to the formation of the Eurasian supercontinent during Paleozoic time, but the views on this complicated process remain very disparate and sometimes controversial. Three volcanic formations of the Middle Silurian, LowertoMiddle Devonian and Middle Devonian age from the southwestern boundary of the Chingiz Range (NE Kazakhstan yields what are interpreted as primary paleomagnetic directions that help clarify the evolution of the belt. A singlepolarity characteristic component in midSilurian andesites yields a positive intraformational conglomerate test, whereas dualpolarity prefolding components are isolated from the two Devonian collections. These new data were evaluated together with previously published paleomagnetic results from Paleozoic rocks in the Chingiz Range, and allow us to establish with confidence the hemisphere in which the area was located at a given time. We conclude that NE Kazakhstan was steadily moving northward crossing the equator in Silurian time. These new paleomagnetic data from the Chingiz range also agree with and reinforce the hypothesis that the strongly curved volcanic belts of Kazakhstan underwent oroclinal bending between Middle Devonian and Late Carboniferous time. A comparison of the Chingiz paleolatitudes with those of Siberia shows similarities between the northward motion and rotational history of the Chingiz unit and those of Siberia, which imposes important constraints on the evolving paleogeography of the Ural-Mongol belt.

A Study of Nonlinear Elasticity Effects on Permeability of Stress Sensitive Shale Rocks Using an Improved Coupled Flow and Geomechanics Model: A Case Study of the Longmaxi Shale in China

Directory of Open Access Journals (Sweden)

Chenji Wei

2018-02-01

Full Text Available Gas transport in shale gas reservoirs is largely affected by rock properties such as permeability. These properties are often sensitive to the in-situ stress state changes. Accurate modeling of shale gas transport in shale reservoir rocks considering the stress sensitive effects on rock petrophysical properties is important for successful shale gas extraction. Nonlinear elasticity in stress sensitive reservoir rocks depicts the nonlinear stress-strain relationship, yet it is not thoroughly studied in previous reservoir modeling works. In this study, an improved coupled flow and geomechanics model that considers nonlinear elasticity is proposed. The model is based on finite element methods, and the nonlinear elasticity in the model is validated with experimental data on shale samples selected from the Longmaxi Formation in Sichuan Basin China. Numerical results indicate that, in stress sensitive shale rocks, nonlinear elasticity affects shale permeability, shale porosity, and distributions of effective stress and pore pressure. Elastic modulus change is dependent on not only in-situ stress state but also stress history path. Without considering nonlinear elasticity, the modeling of shale rock permeability in Longmaxi Formation can overestimate permeability values by 1.6 to 53 times.

Legal Regime of Shale Gas Extraction

OpenAIRE

Ovidiu – Horia Maican

2013-01-01

Some countries with large reserves intend to promote shale gas production, in order to reduce their dependency on imported gas. Shale gas will be an important new aspect in the world energy scene, with many effects. European Union wants secure and affordable sources of energy. Natural gas is the cleanest fossil fuel and a vital component of European Union's energy strategy. One of the most important aspects is that gas produces significantly cleaner energy than other fossil fuels. From a lega...

Shale: an overlooked option for US nuclear waste disposal

Science.gov (United States)

Neuzil, Christopher E.

2014-01-01

Toss a dart at a map of the United States and, more often than not, it will land where shale can be found underground. A drab, relatively featureless sedimentary rock that historically attracted little interest, shale (as used here, the term includes clay and a range of clay-rich rocks) is entering Americans’ consciousness as a new source of gas and oil. But shale may also offer something entirely different—the ability to safely and permanently house high-level nuclear waste.

Shale gas production: potential versus actual greenhouse gas emissions

OpenAIRE

O'Sullivan, Francis Martin; Paltsev, Sergey

2012-01-01

Estimates of greenhouse gas (GHG) emissions from shale gas production and use are controversial. Here we assess the level of GHG emissions from shale gas well hydraulic fracturing operations in the United States during 2010. Data from each of the approximately 4000 horizontal shale gas wells brought online that year are used to show that about 900 Gg CH[subscript 4] of potential fugitive emissions were generated by these operations, or 228 Mg CH[subscript 4] per well—a figure inappropriately ...

Using Neutrons to Study Fluid-Rock Interactions in Shales

Science.gov (United States)

DiStefano, V. H.; McFarlane, J.; Anovitz, L. M.; Gordon, A.; Hale, R. E.; Hunt, R. D.; Lewis, S. A., Sr.; Littrell, K. C.; Stack, A. G.; Chipera, S.; Perfect, E.; Bilheux, H.; Kolbus, L. M.; Bingham, P. R.

2015-12-01

Recovery of hydrocarbons by hydraulic fracturing depends on complex fluid-rock interactions that we are beginning to understand using neutron imaging and scattering techniques. Organic matter is often thought to comprise the majority of porosity in a shale. In this study, correlations between the type of organic matter embedded in a shale and porosity were investigated experimentally. Selected shale cores from the Eagle Ford and Marcellus formations were subjected to pyrolysis-gas chromatography, Differential Thermal Analysis/Thermogravimetric analysis, and organic solvent extraction with the resulting affluent analyzed by gas chromatography-mass spectrometry. The pore size distribution of the microporosity (~1 nm to 2 µm) in the Eagle Ford shales was measured before and after solvent extraction using small angle neutron scattering. Organics representing mass fractions of between 0.1 to 1 wt.% were removed from the shales and porosity generally increased across the examined microporosity range, particularly at larger pore sizes, approximately 50 nm to 2 μm. This range reflects extraction of accessible organic material, including remaining gas molecules, bitumen, and kerogen derivatives, indicating where the larger amount of organic matter in shale is stored. An increase in porosity at smaller pore sizes, ~1-3 nm, was also present and could be indicative of extraction of organic material stored in the inter-particle spaces of clays. Additionally, a decrease in porosity after extraction for a sample was attributed to swelling of pores with solvent uptake. This occurred in a shale with high clay content and low thermal maturity. The extracted hydrocarbons were primarily paraffinic, although some breakdown of larger aromatic compounds was observed in toluene extractions. The amount of hydrocarbon extracted and an overall increase in porosity appeared to be primarily correlated with the clay percentage in the shale. This study complements fluid transport neutron

Development of Shale Gas Supply Chain Network under Market Uncertainties

Directory of Open Access Journals (Sweden)

Jorge Chebeir

2017-02-01

Full Text Available The increasing demand of energy has turned the shale gas and shale oil into one of the most promising sources of energy in the United States. In this article, a model is proposed to address the long-term planning problem of the shale gas supply chain under uncertain conditions. A two-stage stochastic programming model is proposed to describe and optimize the shale gas supply chain network. Inherent uncertainty in final products’ prices, such as natural gas and natural gas liquids (NGL, is treated through the utilization of a scenario-based method. A binomial option pricing model is utilized to approximate the stochastic process through the generation of scenario trees. The aim of the proposed model is to generate an appropriate and realistic supply chain network configuration as well as scheduling of different operations throughout the planning horizon of a shale gas development project.

Characterization of nanoporous shales with gas sorption

Science.gov (United States)

Joewondo, N.; Prasad, M.

2017-12-01

The understanding of the fluid flow in porous media requires the knowledge of the pore system involved. Fluid flow in fine grained shales falls under different regime than transport regime in conventional reservoir due to the different average pore sizes in the two materials; the average pore diameter of conventional sandstones is on the micrometer scale, while of shales can be as small as several nanometers. Mercury intrusion porosimetry is normally used to characterize the pores of conventional reservoir, however with increasingly small pores, the injection pressure required to imbibe the pores becomes infinitely large due to surface tension. Characterization of pores can be expressed by a pore size distribution (PSD) plot, which reflects distribution of pore volume or surface area with respect to pore size. For the case of nanoporous materials, the surface area, which serves as the interface between the rock matrix and fluid, becomes increasingly large and important. Physisorption of gas has been extensively studied as a method of nanoporous solid characterization (particularly for the application of catalysis, metal organic frameworks, etc). The PSD is obtained by matching the experimental result to the calculated theoretical result (using Density Functional Theory (DFT), a quantum mechanics based modelling method for molecular scale interactions). We present the challenges and experimental result of Nitrogen and CO2 gas sorption on shales with various mineralogy and the interpreted PSD obtained by DFT method. Our result shows significant surface area contributed by the nanopores of shales, hence the importance of surface area measurements for the characterization of shales.

Devonian post-orogenic extension-related volcano-sedimentary rocks in the northern margin of the Tibetan Plateau, NW China: Implications for the Paleozoic tectonic transition in the North Qaidam Orogen

Science.gov (United States)

Qin, Yu; Feng, Qiao; Chen, Gang; Chen, Yan; Zou, Kaizhen; Liu, Qian; Jiao, Qianqian; Zhou, Dingwu; Pan, Lihui; Gao, Jindong

2018-05-01

The Maoniushan Formation in the northern part of the North Qaidam Orogen (NQO), NW China, contains key information on a Paleozoic change in tectonic setting of the NQO from compression to extension. Here, new zircon U-Pb, petrological, and sedimentological data for the lower molasse sequence of the Maoniushan Formation are used to constrain the timing of this tectonic transition. Detrital zircons yield U-Pb ages of 3.3-0.4 Ga with major populations at 0.53-0.4, 1.0-0.56, 2.5-1.0, and 3.3-2.5 Ga. The maximum depositional age of the Maoniushan Formation is well constrained by a youngest detrital zircon age of ∼409 Ma. Comparing these dates with geochronological data for the region indicates that Proterozoic-Paleozoic zircons were derived mainly from the NQO as well as the Oulongbuluk and Qaidam blocks, whereas Archean zircons were probably derived from the Oulongbuluk Block and the Tarim Craton. The ∼924, ∼463, and ∼439 Ma tectonothermal events recorded in this region indicate that the NQO was involved in the early Neoproterozoic assembly of Rodinia and early Paleozoic microcontinental convergence. A regional angular unconformity between Devonian and pre-Devonian strata within the NQO suggests a period of strong mountain building between the Oulongbuluk and Qaidam blocks during the Silurian, whereas an Early Devonian post-orogenic molasse, evidence of extensional collapse, and Middle to Late Devonian bimodal volcanic rocks and Carboniferous marine carbonate rocks clearly reflect long-lived tectonic extension. Based on these results and the regional geology, we suggest that the Devonian volcano-sedimentary rocks within the NQO were formed in a post-orogenic extensional setting similar to that of the East Kunlun Orogen, indicating that a major tectonic transition from compression to extension in these two orogens probably commenced in the Early Devonian.

Shale gas: the new energetic deal. Technical, ecological and geostrategic issues

International Nuclear Information System (INIS)

Charon, Guillaume

2014-09-01

The author proposes a view on the shale gas industry, and explains how this resource deeply transforms the energy world and economic and geostrategic power relations. In order to make things clear, the author notably indicates how many wind turbines would replace shale gas production, what environmental risks are and how to avoid them, what is the impact of shale gas on energy price, why most of major companies missed this turn and why some producing countries are against shale gas, and in which countries shale gas will probably be developed. The chapters address the following topics: non conventional gas, exploration and production, transport, storage and commercialisation, productions costs with simulation examples, economic assessment, strategy of actors, environmental assessment, debate, world overview

Impact of Shale Gas Development on Water Resource in Fuling, China

Science.gov (United States)

Yang, Hong; Huang, Xianjin; Yang, Qinyuan; Tu, Jianjun

2015-04-01

As a low-carbon energy, shale gas rapidly developed in U.S. in last years due to the innovation of the technique of hydraulic fracture, or fracking. Shale gas boom produces more gas with low price and reduced the reliance on fuel import. To follow the American shale gas success, China made an ambitious plan of shale gas extraction, 6.5 billion m3 by 2015. To extract shale gas, huge amount water is needed to inject into each gas well. This will intensify the competition of water use between industry, agricultural and domestic sectors. It may finally exacerbate the water scarcity in China. After the extraction, some water was returned to the ground. Without adequate treatment, the flowback water can introduce heavy metal, acids, pesticides, and other toxic material into water and land. This may inevitably worsen the water and land contamination. This study analysed the potential water consumption and wastewater generation in shale gas development in Fuling, Southwest China. The survey found the average water consumption is 30,000 cubic meter for one well, higher than shale well in U.S. Some 2%-20% water flowed back to the ground. The water quality monitoring showed the Total Suspended Solid (TSS) and Chemical Oxygen Demand (COD) were the main factors above those specified by China's water regulation. Shale gas is a lower-carbon energy, but it is important to recognize the water consuming and environmental pollution during the fracking. Strict monitoring and good coordination during the shale gas exploitation is urgently needed for the balance of economic development, energy demand and environmental protection.

The role of alkenes produced during hydrous pyrolysis of a shale

Energy Technology Data Exchange (ETDEWEB)

Leif, R.N.; Simoneit, B.R.T. [Oregon State Univ., Corvallis, OR (United States). College of Oceanic and Atmospheric Sciences

2000-07-01

Hydrous pyrolysis experiments conducted on Messel shale with D{sub 2}O demonstrated that a large amount of deuterium becomes incorporated into the hydrocarbons generated from the shale kerogen. In order to understand the pathway of deuterium (and protium) exchange and the role of water during hydrous pyrolysis, we conducted a series of experiments using aliphatic compounds (1,13-tetradecadiene, 1-hexadecene, eicosane and dotriacontane) as probe molecules. These compounds were pyrolyzed in D{sub 2}O, shale/D{sub 2}O, and shale/H{sub 2}O and the products analyzed by GC-MS. In the absence of powdered shale, the incorporation of deuterium from D{sub 2}O occurred only in olefinic compounds via double bond isomerization. The presence of shale accelerated deuterium incorporation into the olefins and resulted in a minor amount of deuterium incorporation in the saturated n-alkanes. The pattern of deuterium substitution of the diene closely matched the deuterium distribution observed in the n-alkanes generated from the shale kerogen in the D{sub 2}O/shale pyrolyses. The presence of the shale also resulted in reduction (hydrogenation) of olefins to saturated n-alkanes with concomitant oxidation of olefins to ketones. These results show that under hydrous pyrolysis conditions, kerogen breakdown generates n-alkanes and terminal n-alkenes by free radical hydrocarbon cracking of the aliphatic kerogen structure. The terminal n-alkenes rapidly isomerize to internal alkenes via acid-catalyzed isomerization under hydrothermal conditions, a significant pathway of deuterium (and protium) exchange between water and the hydrocarbons. These n-alkenes simultaneously undergo reduction to n-alkanes (major) or oxidation to ketones (minor) via alcohols formed by the hydration of the alkenes. (Author)

Hydrogen retorting of oil shales from Eastern Canada

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. (CANMET, Ottawa, Ontario (Canada)); Synnott, J.; Boorman, R.S.; Salter, R.S.

1984-04-01

The liquid production potential of thirty oil shale samples from Eastern Canada was determined by Fischer assay retort and pyrochem retort. For all shales, the presence of hydrogen during pyrochem retorting resulted in a significant increase in oil yields compared to Fischer assay yields. Ten oil shale samples were selected for detailed evaluation in the pyrochem retort in the presence of nitrogen and hydrogen. Besides increasing yields, the presence of hydrogen lowered the specific gravity of liquid products and the content of sulphur but increased the content of nitrogen. This was attributed to the stabilization of precursors to nitrogen compounds which prevented their polymerization. (J.H.K.)

Petrological, geochemical, isotopic, and geochronological constraints for the Late Devonian-Early Carboniferous magmatism in SW Gondwana (27-32°LS): an example of geodynamic switching

Science.gov (United States)

Dahlquist, Juan A.; Alasino, Pablo H.; Basei, Miguel A. S.; Morales Cámera, Matías M.; Macchioli Grande, Marcos; da Costa Campos Neto, Mario

2018-04-01

We report a study integrating 13 new U-Pb LA-MC-ICP-MS zircon ages and Hf-isotope data from dated magmatic zircons together with complete petrological and whole-rock geochemistry data for the dated granitic rocks. Sample selection was strongly based on knowledge reported in previous investigations. Latest Devonian-Early Carboniferous granite samples were collected along a transect of 900 km, from the inner continental region (present-day Eastern Sierras Pampeanas) to the magmatic arc (now Western Sierras Pampeanas and Frontal Cordillera). Based on these data together with ca. 100 published whole-rock geochemical analyses we conclude that Late Devonian-Early Carboniferous magmatism at this latitude represents continuous activity (ranging from 322 to 379 Ma) on the pre-Andean margin of SW Gondwana, although important whole-rock and isotopic compositional variations occurred through time and space. Combined whole-rock chemistry and isotope data reveal that peraluminous A-type magmatism started in the intracontinental region during the Late Devonian, with subsequent development of synchronous Carboniferous peraluminous and metaluminous A-type magmatism in the retro-arc region and calc-alkaline magmatism in the western paleomargin. We envisage that magmatic evolution was mainly controlled by episodic fluctuations in the angle of subduction of the oceanic plate (between flat-slab and normal subduction), supporting a geodynamic switching model. Subduction fluctuations were relatively fast (ca. 7 Ma) during the Late Devonian and Early Carboniferous, and the complete magmatic switch-off and switch-on process lasted for 57 Ma. Hf T DM values of zircon (igneous and inherited) from some Carboniferous peraluminous A-type granites in the retro-arc suggest that Gondwana continental lithosphere formed during previous orogenies was partly the source of the Devonian-Carboniferous granitic magmas, thus precluding the generation of the parental magmas from exotic terranes.

Shale oil specialty markets: Screening survey for United States applications

Energy Technology Data Exchange (ETDEWEB)

1987-12-01

EG and G requested J. E. Sinor Consultants Inc. to carry out an initial screening study on the possibilities for producing specialty chemicals from oil shale. Raw shale oil is not an acceptable feedstock to refineries and there are not enough user of heavy fuel oil in the western oil shale region to provide a dependable market. The only alternatives are to hydrotreat the oil, or else ship it long distances to a larger market area. Either of these alternatives results in a cost penalty of several dollars per barrel. Instead of attempting to enter the large-volume petroleum products market, it was hypothesized that a small shale oil facility might be able to produce specialty chemicals with a high enough average value to absorb the high costs of shipping small quantities to distant markets and still provide a higher netback to the plant site than sales to the conventional petroleum products market. This approach, rather than attempting to refine shale oil or to modify its characteristics to satisfy the specifications for petroleum feedstocks or products, focuses instead on those particular characteristics which distinguish shale oil from petroleum, and attempts to identify applications which would justify a premium value for those distinctive characteristics. Because byproducts or specialty chemicals production has been a prominent feature of oil shale industries which have flourished for periods of time in various countries, a brief review of those industries provides a starting point for this study. 9 figs., 32 tabs.

Shale gas: don't burn your bridges

International Nuclear Information System (INIS)

Dupin, L.; Casalonga, S.

2011-01-01

As debates take place in the French Parliament to forbid the extraction of shale in gas in France, the author outlines that, according to some experts, even though some sites might be very interesting, only a fraction of their content could be exploited. He also outlines the actual danger of this exploitation for the environment, notably because hydraulic fracturing has to be used. Although the main operators are American, French big companies possess the required know-how and are gaining experience abroad. Moreover, it seems that shale gas exploitation does not possess a significant job creation potential. The situation of different countries with respect to shale gas exploitation is briefly presented: United States, Canada, China, and Poland. The United States policy on this issue is more precisely described in a last article

Liquid oil production from shale gas condensate reservoirs

Science.gov (United States)

Sheng, James J.

2018-04-03

A process of producing liquid oil from shale gas condensate reservoirs and, more particularly, to increase liquid oil production by huff-n-puff in shale gas condensate reservoirs. The process includes performing a huff-n-puff gas injection mode and flowing the bottom-hole pressure lower than the dew point pressure.

Oil shale energy and some alternatives in Estonia

International Nuclear Information System (INIS)

Oepik, I.

2002-01-01

An academic lecture delivered by prof. Ilmar Oepik at the Thermal Engineering Department of Tallinn Technical University in Dec. 2000 to mark the 120 semesters since the cum laude diploma of a mechanical engineer discusses about ineffective utilization of oil shale and developing renewable resources as an alternative to oil shale

Stress dependence of permeability of intact and fractured shale cores.

Science.gov (United States)

van Noort, Reinier; Yarushina, Viktoriya

2016-04-01

Whether a shale acts as a caprock, source rock, or reservoir, understanding fluid flow through shale is of major importance for understanding fluid flow in geological systems. Because of the low permeability of shale, flow is thought to be largely confined to fractures and similar features. In fracking operations, fractures are induced specifically to allow for hydrocarbon exploration. We have constructed an experimental setup to measure core permeabilities, using constant flow or a transient pulse. In this setup, we have measured the permeability of intact and fractured shale core samples, using either water or supercritical CO2 as the transporting fluid. Our measurements show decreasing permeability with increasing confining pressure, mainly due to time-dependent creep. Furthermore, our measurements show that for a simple splitting fracture, time-dependent creep will also eliminate any significant effect of this fracture on permeability. This effect of confinement on fracture permeability can have important implications regarding the effects of fracturing on shale permeability, and hence for operations depending on that.

Shale-gas wells as virtual storage for supporting intermittent renewables

International Nuclear Information System (INIS)

Knudsen, Brage Rugstad; Foss, Bjarne

2017-01-01

Mature shale-gas wells possess a property that enables cyclic production and shut-in without incurring revenue losses. Based on this property, we suggest that fields with mature shale-gas wells may act as virtual gas storage for supplying fast-ramping gas power plants which balance intermittent renewable generation. By enabling gas supply to power plants to circumvent intermediate third-party storage, we argue that the proposed integration facilitates demand-driven gas production, and discuss how the scheme may support utilization of renewables and reduce supply-related greenhouse-gas emissions in electricity generation. - Highlights: • A novel integration strategy of shale gas and renewable electricity generation. • Mature shale-gas wells enable shut-ins without incurring revenue losses. • This property enables the use mature shale-gas wells as virtual gas storage. • Proposed scheme facilitates demand-driven gas production. • Omitting intermediate gas storage reduces GHG emissions from producer to end-user.

Breakthrough and prospect of shale gas exploration and development in China

OpenAIRE

Dazhong Dong; Yuman Wang; Xinjing Li; Caineng Zou; Quanzhong Guan; Chenchen Zhang; Jinliang Huang; Shufang Wang; Hongyan Wang; Honglin Liu; Wenhua Bai; Feng Liang; Wen Lin; Qun Zhao; Dexun Liu

2016-01-01

In the past five years, shale gas exploration and development has grown in a leaping-forward way in China. Following USA and Canada, China is now the third country where industrial shale gas production is realized, with the cumulative production exceeding 60 × 108 m3 until the end of 2015. In this paper, the main achievements of shale gas exploration and development in China in recent years were reviewed and the future development prospect was analyzed. It is pointed out that shale gas explor...

Cyclone oil shale retorting concept. [Use it all retorting process

Energy Technology Data Exchange (ETDEWEB)

Harak, A.E.; Little, W.E.; Faulders, C.R.

1984-04-01

A new concept for above-ground retorting of oil shale was disclosed by A.E. Harak in US Patent No. 4,340,463, dated July 20, 1982, and assigned to the US Department of Energy. This patent titled System for Utilizing Oil Shale Fines, describes a process wherein oil shale fines of one-half inch diameter and less are pyrolyzed in an entrained-flow reactor using hot gas from a cyclone combustor. Spent shale and supplemental fuel are burned at slagging conditions in this combustor. Because of fines utilization, the designation Use It All Retorting Process (UIARP) has been adopted. A preliminary process engineering design of the UIARP, analytical tests on six samples of raw oil shale, and a preliminary technical and economic evaluation of the process were performed. The results of these investigations are summarized in this report. The patent description is included. It was concluded that such changes as deleting air preheating in the slag quench and replacing the condenser with a quench-oil scrubber are recognized as being essential. The addition of an entrained flow raw shale preheater ahead of the cyclone retort is probably required, but final acceptance is felt to be contingent on some verification that adequate reaction time cannot be obtained with only the cyclone, or possibly some other twin-cyclone configuration. Sufficient raw shale preheating could probably be done more simply in another manner, perhaps in a screw conveyor shale transporting system. Results of the technical and economic evaluations of Jacobs Engineering indicate that further investigation of the UIARP is definitely worthwhile. The projected capital and operating costs are competitive with costs of other processes as long as electric power generation and sales are part of the processing facility.

Lithium recovery from shale gas produced water using solvent extraction

International Nuclear Information System (INIS)

Jang, Eunyoung; Jang, Yunjai; Chung, Eunhyea

2017-01-01

Shale gas produced water is hypersaline wastewater generated after hydraulic fracturing. Since the produced water is a mixture of shale formation water and fracturing fluid, it contains various organic and inorganic components, including lithium, a useful resource for such industries as automobile and electronics. The produced water in the Marcellus shale area contains about 95 mg/L lithium on average. This study suggests a two-stage solvent extraction technique for lithium recovery from shale gas produced water, and determines the extraction mechanism of ions in each stage. All experiments were conducted using synthetic shale gas produced water. In the first-stage, which was designed for the removal of divalent cations, more than 94.4% of Ca"2"+, Mg"2"+, Sr"2"+, and Ba"2"+ ions were removed by using 1.0 M di-(2-ethylhexyl) phosphoric acid (D2EHPA) as an extractant. In the second-stage, for lithium recovery, we could obtain a lithium extraction efficiency of 41.2% by using 1.5 M D2EHPA and 0.3 M tributyl phosphate (TBP). Lithium loss in the first-stage was 25.1%, and therefore, the total amount of lithium recovered at the end of the two-step extraction procedure was 30.8%. Through this study, lithium, one of the useful mineral resources, could be selectively recovered from the shale gas produced water and it would also reduce the wastewater treatment cost during the development of shale gas. - Highlights: • Lithium was extracted from shale gas produced water using an organic solvent. • Two-stage solvent extraction technique was applied. • Divalent cations were removed in the first stage by D2EHPA. • Lithium was selectively recovered in the second stage by using TBP with D2EHPA.

Future strategies for oil shale development as a new indigenous energy resource in Jordan

International Nuclear Information System (INIS)

Jaber, J.O.; Tarawneh, T.

2011-01-01

Indigenous oil shale deposits could satisfy Jordan's demand for liquid and gaseous fuels as well as electricity for many centuries. Markets also exist for raw and retorted oil shale, spent shale, and for sulfur recovered during the upgrading and refining of crude shale oil. Although the potential benefits of oil shale development are substantial, complex and expensive facilities would be required, and these have serious economic, environmental, and social implications for the Kingdom and its people. In January 2006, the United States Trade and Development Agency (USTDA) awarded a grant to the Jordanian Ministry of Planning and International Cooperation to support the analysis of current oil shale processing technologies and the application of international expertise to the development of a oil shale industry in Jordan. The goal of the technical assistance project was to help the Government of Jordan (GoJ) establish short and long-term strategies for oil shale development and to facilitate the commercial production of shale oil in the country. This paper discusses the results of the project. The Kingdom's current energy situation and its previous work on oil shale are summarized, and the incentives and restraints on oil shale commercialization are described. Impediments to development are identified, and possible governmental responses are assessed. (author)

The influence of global sea level changes on European shale distribution and gas exploration

Energy Technology Data Exchange (ETDEWEB)

Turner, P.; Cornelius, C.T.; Clarke, H. [Cuadrilla Resources Ltd., Staffordshire (United Kingdom)

2010-07-01

Technological advances in directional drilling and hydraulic fracturing technology have unlocked new supplies of shale gas from reservoirs that were previously considered to be uneconomic. Several companies, both experienced majors and small independents, are currently evaluating the unconventional resource potential of mainland Europe. This paper demonstrated that global sea level changes govern the distribution of marine black shales. The Hallam Curve was used in this study to identify periods of prospective gas shale deposition. In general, these correspond to post-glacial periods of relatively high sea level. Under-filled marginal sedimentary basins are key exploration targets. The geochemical and petrophysical characteristics of the shales deposited under these conditions are often comparable to North American shales, particularly the Barnett Shale which is currently in production. Many orogenic events influence European shales in terms of organic maturity, hydrocarbon generation and fracture generation. The main prospective horizons in ascending stratigraphic sequence are the Alum Shale, Llandovery Shale, Fammenian/Frasnian Shale, Serpukhovian Shale, Toarcian Shale, Kimmeridge Clay and the Tertiary Eocene and Oligocene shales common to central Europe. This paper presented the authors initial exploration strategy, with particular focus on the Lower Palaeozoic of central Europe, the Namurian of northwest England and the Jurassic Posidonia Formation of the Roer Valley Graben in Holland. The potential obstacles to unconventional exploration in Europe include restricted access to surface locations, high water usage, a lack of convenient pipeline infrastructure, strict environmental regulations, a high population density and lack of suitable drilling rigs and well completion equipment. 13 refs., 7 figs.

Observations of the release of non-methane hydrocarbons from fractured shale.

Science.gov (United States)

Sommariva, Roberto; Blake, Robert S; Cuss, Robert J; Cordell, Rebecca L; Harrington, Jon F; White, Iain R; Monks, Paul S

2014-01-01

The organic content of shale has become of commercial interest as a source of hydrocarbons, owing to the development of hydraulic fracturing ("fracking"). While the main focus is on the extraction of methane, shale also contains significant amounts of non-methane hydrocarbons (NMHCs). We describe the first real-time observations of the release of NMHCs from a fractured shale. Samples from the Bowland-Hodder formation (England) were analyzed under different conditions using mass spectrometry, with the objective of understanding the dynamic process of gas release upon fracturing of the shale. A wide range of NMHCs (alkanes, cycloalkanes, aromatics, and bicyclic hydrocarbons) are released at parts per million or parts per billion level with temperature- and humidity-dependent release rates, which can be rationalized in terms of the physicochemical characteristics of different hydrocarbon classes. Our results indicate that higher energy inputs (i.e., temperatures) significantly increase the amount of NMHCs released from shale, while humidity tends to suppress it; additionally, a large fraction of the gas is released within the first hour after the shale has been fractured. These findings suggest that other hydrocarbons of commercial interest may be extracted from shale and open the possibility to optimize the "fracking" process, improving gas yields and reducing environmental impacts.

Shale gases, a windfall for France?

International Nuclear Information System (INIS)

Tonnac, Alain de; Perves, Jean-Pierre

2013-11-01

After having recalled the definition and origin of shale gases, the different non conventional gases and their exploitation techniques (hydraulic fracturing and horizontal drilling) this report examines whether these gases are an opportunity for France. Some characteristics and data of the fossil and gas markets are presented and commented: world primary energy consumption, proved reserves of non conventional gases and their locations, European regions which may possess reserves of shale gases and coal-bed methane, origins of gas imports in France. The second part addresses shale gas deposits and their exploitation: discussion of the influence of the various rock parameters, evolution of production. The third part discusses the exploitation techniques and specific drilling tools. The issue of exploitation safety and security is addressed as well as the associated controversies: about the pollution of underground waters, about the fact that deep drillings result in pollution, about the risks associated with hydraulic fracturing and injections of chemical products, about the hold on ground and site degradation, about water consumption, about pollution due to gas pipeline leakage, about seismic risk, about noise drawbacks, about risks for health, about exploration and production authorization and license, and about air pollution and climate. The last part addresses the French situation and its future: status of the energy bill, recommendations made by a previous government, cancellation of authorizations, etc. Other information are provided in appendix about non conventional hydrocarbons, about shale gas exploitation in the USA, and about the Lacq gas

Naval Petroleum and Oil Shale Reserves

International Nuclear Information System (INIS)

1992-01-01

During fiscal year 1992, the reserves generated $473 million in revenues, a $181 million decrease from the fiscal year 1991 revenues, primarily due to significant decreases in oil and natural gas prices. Total costs were $200 million, resulting in net cash flow of $273 million, compared with $454 million in fiscal year 1991. From 1976 through fiscal year 1992, the Naval Petroleum and Oil Shale Reserves generated more than $15 billion in revenues and a net operating income after costs of $12.5 billion. In fiscal year 1992, production at the Naval Petroleum Reserves at maximum efficient rates yielded 26 million barrels of crude oil, 119 billion cubic feet of natural gas, and 164 million gallons of natural gas liquids. From April to November 1992, senior managers from the Naval Petroleum and Oil Shale Reserves held a series of three workshops in Boulder, Colorado, in order to build a comprehensive Strategic Plan as required by Secretary of Energy Notice 25A-91. Other highlights are presented for the following: Naval Petroleum Reserve No. 1--production achievements, crude oil shipments to the strategic petroleum reserve, horizontal drilling, shallow oil zone gas injection project, environment and safety, and vanpool program; Naval Petroleum Reserve No. 2--new management and operating contractor and exploration drilling; Naval Petroleum Reserve No. 3--steamflood; Naval Oil Shale Reserves--protection program; and Tiger Team environmental assessment of the Naval Petroleum and Oil Shale Reserves in Colorado, Utah, and Wyoming

Climate impact of potential shale gas production in the EU

Energy Technology Data Exchange (ETDEWEB)

Forster, D.; Perks, J. [AEA Technology plc, London (United Kingdom)

2012-07-15

Existing estimates of GHG emissions from shale gas production and available abatement options were used to obtain improved estimates of emissions from possible shale gas exploitation in the EU. GHG emissions per unit of electricity generated from shale gas were estimated to be around 4 to 8% higher than for electricity generated by conventional pipeline gas from within Europe. These additional emissions arise in the pre-combustion stage, predominantly in the well completion phase when the fracturing fluid is brought back to the surface together with released methane. If emissions from well completion are mitigated, through flaring or capture, and utilised, then this difference is reduced to 1 to 5%. The analysis suggests that the emissions from shale gas-based power generation (base case) are 2 to 10% lower than those from electricity generated from sources of conventional pipeline gas located outside of Europe (in Russia and Algeria), and 7 to 10% lower than those from electricity generated from LNG imported into Europe. However, under our 'worst case' shale gas scenario, where all flow back gases at well completion are vented, emissions from electricity generated from shale gas would be similar to the upper emissions level for electricity generated from imported LNG and for gas imported from Russia.

Climate impact of potential shale gas production in the EU

Energy Technology Data Exchange (ETDEWEB)

Forster, D.; Perks, J. [AEA Technology plc, London (United Kingdom)

2012-07-15

Existing estimates of GHG emissions from shale gas production and available abatement options were used to obtain improved estimates of emissions from possible shale gas exploitation in the EU. GHG emissions per unit of electricity generated from shale gas were estimated to be around 4 to 8% higher than for electricity generated by conventional pipeline gas from within Europe. These additional emissions arise in the pre-combustion stage, predominantly in the well completion phase when the fracturing fluid is brought back to the surface together with released methane. If emissions from well completion are mitigated, through flaring or capture, and utilised, then this difference is reduced to 1 to 5%. The analysis suggests that the emissions from shale gas-based power generation (base case) are 2 to 10% lower than those from electricity generated from sources of conventional pipeline gas located outside of Europe (in Russia and Algeria), and 7 to 10% lower than those from electricity generated from LNG imported into Europe. However, under our 'worst case' shale gas scenario, where all flow back gases at well completion are vented, emissions from electricity generated from shale gas would be similar to the upper emissions level for electricity generated from imported LNG and for gas imported from Russia.

Regulating hydraulic fracturing in shale gas plays: The case of Texas

International Nuclear Information System (INIS)

Rahm, Dianne

2011-01-01

The ability to economically produce natural gas from unconventional shale gas reservoirs has been made possible recently through the application of horizontal drilling and hydraulic fracturing. This new technique has radically changed the energy future of the United States. The U.S. has shifted from a waning producer of natural gas to a growing producer. The Energy Information Administration forecasts that by 2035 nearly half of U.S. natural gas will come from shale gas. Texas is a major player in these developments. Of the eight states and coastal areas that account for the bulk of U.S. gas, Texas has the largest proved reserves. Texas' Barnett Shale already produces six percent of the continental U.S.' gas and exploration of Texas' other shale gas regions is just beginning. Shale gas production is highly controversial, in part because of environmental concerns. Some U.S. states have put hydraulic fracturing moratoriums in place because of fear of drinking water contamination. The federal government has gotten involved and some states, like Texas, have accused it of overreaching. The contention over shale gas drilling in the U.S. may be a bellwether for other parts of the world that are now moving forward with their own shale gas production. - Highlights: → Shale gas production through hydraulic fracturing and horizontal drilling techniques has transformed natural gas production in the United States and portents to do so for the world. → Hydraulic fracturing is highly controversial in part because of fears of environmental impacts particularly on drinking water resources. → The boom in shale gas production is not likely to be stopped because of the amount of resource available, the need for the resource, and the amount of money to be made from production.

Proceedings of the first thermomechanical workshop for shale

International Nuclear Information System (INIS)

1986-03-01

Chapter 2 provides a description of the three federal regulations that pertain to the development of a high-level nuclear waste repository regardless of the rock type. Chapter 3 summarizes the reference shale repository conditions selected for this workshop. A room-and-pillar configuration was considered at an extraction ratio of about 0.25. The depth was assumed to be 700 m. Chapter 4 gives a summary of several case histories that were considered to be valuable in gaining an understanding of some of the design and construction features that might be unique in creating underground openings in shale. Chapter 5 assesses the data and information needs, availability, technology for acquisition, and the research and development necessary for analytical/numerical modeling in heat transfer, fluid flow, and thermomechanics. Chapter 6 assesses data and information needs in the laboratory and considerations associated with shale rock characterization. Chapter 7 assesses the data and information needs, availability, technology for acquisition, and the research and development necessary for field/in situ testing. Chapter 8 presents the consensus of the workshop participants that there is a definite need to advance the state of knowledge concerning the thermomechanical behavior of shales and to gain experience in applying this knowledge to the design of room-and-pillar excavations. Finally, Chapter 9 provides a summary of the research and development needs in the various interacting activities of repository development, including analytical/numerical modeling, laboratory testing, and field/in situ testing. The main conclusion of the workshop was that a need exists for an aggressive program in laboratory, field, numerical modeling, and design studies to provide a thermomechanical, technological base for comparison of shale types and shale regions/areas/sites

Volume fracturing of deep shale gas horizontal wells

Directory of Open Access Journals (Sweden)

Tingxue Jiang

2017-03-01

Full Text Available Deep shale gas reservoirs buried underground with depth being more than 3500 m are characterized by high in-situ stress, large horizontal stress difference, complex distribution of bedding and natural cracks, and strong rock plasticity. Thus, during hydraulic fracturing, these reservoirs often reveal difficult fracture extension, low fracture complexity, low stimulated reservoir volume (SRV, low conductivity and fast decline, which hinder greatly the economic and effective development of deep shale gas. In this paper, a specific and feasible technique of volume fracturing of deep shale gas horizontal wells is presented. In addition to planar perforation, multi-scale fracturing, full-scale fracture filling, and control over extension of high-angle natural fractures, some supporting techniques are proposed, including multi-stage alternate injection (of acid fluid, slick water and gel and the mixed- and small-grained proppant to be injected with variable viscosity and displacement. These techniques help to increase the effective stimulated reservoir volume (ESRV for deep gas production. Some of the techniques have been successfully used in the fracturing of deep shale gas horizontal wells in Yongchuan, Weiyuan and southern Jiaoshiba blocks in the Sichuan Basin. As a result, Wells YY1HF and WY1HF yielded initially 14.1 × 104 m3/d and 17.5 × 104 m3/d after fracturing. The volume fracturing of deep shale gas horizontal well is meaningful in achieving the productivity of 50 × 108 m3 gas from the interval of 3500–4000 m in Phase II development of Fuling and also in commercial production of huge shale gas resources at a vertical depth of less than 6000 m.

Determination of Porosity in Shale by Double Headspace Extraction GC Analysis.

Science.gov (United States)

Zhang, Chun-Yun; Li, Teng-Fei; Chai, Xin-Sheng; Xiao, Xian-Ming; Barnes, Donald

2015-11-03

This paper reports on a novel method for the rapid determination of the shale porosity by double headspace extraction gas chromatography (DHE-GC). Ground core samples of shale were placed into headspace vials and DHE-GC measurements of released methane gas were performed at a given time interval. A linear correlation between shale porosity and the ratio of consecutive GC signals was established both theoretically and experimentally by comparing with the results from the standard helium pycnometry method. The results showed that (a) the porosity of ground core samples of shale can be measured within 30 min; (b) the new method is not significantly affected by particle size of the sample; (c) the uncertainties of measured porosities of nine shale samples by the present method range from 0.31 to 0.46 p.u.; and (d) the results obtained by the DHE-GC method are in a good agreement with those from the standard helium pycnometry method. In short, the new DHE-GC method is simple, rapid, and accurate, making it a valuable tool for shale gas-related research and applications.

Market analysis of shale oil co-products. Appendices

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

Data are presented in these appendices on the marketing and economic potential for soda ash, aluminia, and nahcolite as by-products of shale oil production. Appendices 1 and 2 contain data on the estimated capital and operating cost of an oil shales/mineral co-products recovery facility. Appendix 3 contains the marketing research data.

Preliminary geotechnical evaluation of deep borehole facilities for nuclear waste disposal in shales

International Nuclear Information System (INIS)

Nataraj, M.S.; New Orleans Univ., LA

1991-01-01

This study is concerned with a preliminary engineering evaluation of borehole facilities for nuclear waste disposal in shales. Some of the geotechnical properties of Pierre, Rhinestreet, and typical illite shale have been collected. The influence of a few geotechnical properties on strength and deformation of host material is briefly examined. It appears that Pierre shale is very unstable and requires support to prevent collapse. Typical illite shale is more stable than Rhinestreet shale, although it undergoes relatively more deformation. 16 refs., 5 figs., 3 tabs

[Chemical hazards arising from shale gas extraction].

Science.gov (United States)

Pakulska, Daria

2015-01-01

The development of the shale industry is gaining momentum and hence the analysis of chemical hazards to the environment and health of the local population is extreiely timely and important. Chemical hazards are created during the exploitation of all minerals, but in the case of shale gas production, there is much more uncertainty as regards to the effects of new technologies application. American experience suggests the increasing risk of environmental contamination, mainly groundwater. The greatest, concern is the incomplete knowledge of the composition of fluids used for fracturing shale rock and unpredictability of long-term effects of hydraulic fracturing for the environment and health of residents. High population density in the old continent causes the problem of chemical hazards which is much larger than in the USA. Despite the growing public discontent data on this subject are limited. First of all, there is no epidemiological studies to assess the relationship between risk factors, such as air and water pollution, and health effects in populations living in close proximity to gas wells. The aim of this article is to identify and discuss existing concepts on the sources of environmental contamination, an indication of the environment elements under pressure and potential health risks arising from shale gas extraction.

Quantitative effects of the shale oil revolution

International Nuclear Information System (INIS)

Belu Mănescu, Cristiana; Nuño, Galo

2015-01-01

The aim of this paper is to analyze the impact of the so-called “shale oil revolution” on oil prices and economic growth. We employ a general equilibrium model of the world oil market in which Saudi Arabia is the dominant firm, with the rest of the producers as a competitive fringe. Our results suggest that most of the expected increase in US oil supply due to the shale oil revolution has already been incorporated into prices and that it will produce an additional increase of 0.2% in the GDP of oil importers in the period 2010–2018. We also employ the model to analyze the collapse in oil prices in the second half of 2014 and conclude that it was mainly due to positive unanticipated supply shocks. - Highlights: • We analyze the impact of the “shale oil revolution” on oil prices and economic growth. • We employ a general equilibrium model of the oil market in which Saudi Arabia is the dominant firm. • We find that most of the shale oil revolution is already priced in. • We also analyze the decline in oil prices in the second half of 2014. • We find that unanticipated supply shocks played the major role in the fall.

Analysis and characterization of trace elements in shale oil and shale oil products by instrumental neutron activation analysis. Master's thesis

International Nuclear Information System (INIS)

Shaw, P.

1978-12-01

Trace elements and their mobilization constitute an important consideration in the development of new fossil fuel technologies. Shale oil produced by in situ retorting of oil shale is an alternative fossil energy source. This study deals with the analysis of trace elements in various shale oil products using instrumental neutron activation analysis (INAA). INAA offers several advantages for those elements for which it is applicable. The greatest advantage is the lack of sample preparation prior to analysis, which greatly simplifies the process and prevents sample contamination. The elements for which analyses are reported in this study are aluminum, antimony, arsenic, bromine, cerium, chlorine, chromium, cobalt, copper, gallium, gold, iodine, iron, manganese, mercury, molybdenum, potassium, selenium, sodium, sulfur, tungsten, vanadium, and zinc

U-Pb zircon geochronology of Late Devonian to Early Carboniferous extension-related silicic volcanism in the northern New England Fold Belt

International Nuclear Information System (INIS)

Bryan, S.E.; Holcombe, R.J.; Fielding, C.R.; Allen, C.M.

2004-01-01

Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) analysis of zircons confirm a Late Devonian to Early Carboniferous age (ca 360-350 Ma) for silicic volcanic rocks of the Campwyn Volcanics and Yarrol terrane of the northern New England Fold Belt (Queensland). These rocks are coeval with silicic volcanism recorded elsewhere in the fold belt at this time (Connors Arch, Drummond Basin). The new U-Pb zircon ages, in combination with those from previous studies, show that silicic magmatism was both widespread across the northern New England Fold Belt (>250 000 km 2 and >500 km inboard of plate margin) and protracted, occurring over a period of -15 million years. Zircon inheritance is commonplace in the Late Devonian - Early Carboniferous volcanics, reflecting anatectic melting and considerable reworking of continental crust. Inherited zircon components range from ca 370 to ca 2050 Ma, with Middle Devonian (385-370 Ma) zircons being common to almost all dated units. Precambrian zircon components record either Precambrian crystalline crust or sedimentary accumulations that were present above or within the zone of magma formation This contrasts with a lack of significant zircon inheritance in younger Permo-Carboniferous igneous rocks intruded through,and emplaced on top of, the Devonian-Carboniferous successions. The inheritance data and location of these volcanic rocks at the eastern margins of the northern New England Fold Belt, coupled with Sr-Nd, Pb isotopic data and depleted mantle model ages for Late Palaeozoic and Mesozoic magmatism, imply that Precambrian mafic and felsic crustal materials (potentially as old as 2050 Ma), or at the very least Lower Palaeozoic rocks derived from the reworking of Precambrian rocks, comprise basement to the eastern parts of the fold belt. This crustal basement architecture may be a relict from the Late Proterozoic breakup of the Rodinian supercontinent. Copyright (2004) Geological Society of Australia

Research and information needs for management of oil shale development

Energy Technology Data Exchange (ETDEWEB)

1983-05-01

This report presents information and analysis to assist BLM in clarifying oil shale research needs. It provides technical guidance on research needs in support of their regulatory responsibilities for onshore mineral activities involving oil shale. It provides an assessment of research needed to support the regulatory and managerial role of the BLM as well as others involved in the development of oil shale resources on public and Indian lands in the western United States.

Patent analysis to identify shale gas development in China and the United States

International Nuclear Information System (INIS)

Lee, Woo Jin; Sohn, So Young

2014-01-01

Shale gas has become an increasingly important form of hydrocarbon energy, and related technologies reflect the geographical characteristics of the countries where the gas is extracted and stored. The United States (U.S.) produces most of the world’s shale gas, while China has the world’s largest shale gas reserves. In this research, we focused on identifying the trends in shale-gas related technologies registered to the United States Patent and Trademark Office (USPTO) and to the State Intellectual Property Office of the People’s Republic of China (SIPO) respectively. To cluster shale-gas related technologies, we text-mined the abstracts of patent specifications. It was found that in the U.S., the key advanced technologies were related to hydraulic fracturing, horizontal drilling, and slick water areas, whereas China had a focus on proppants. The results of our study are expected to assist energy experts in designing energy policies related to technology importation. - Highlights: • We analyzed shale gas-related patent applications in the USPTO and SIPO. • We clustered shale gas patents by text mining patent abstract. • Differences were observed in shale gas technologies developed in the U.S. and China. • We proposed the policies of shale gas exploration and development based on patent analysis

A comprehensive environmental impact assessment method for shale gas development

Directory of Open Access Journals (Sweden)

Renjin Sun

2015-03-01

Full Text Available The great success of US commercial shale gas exploitation stimulates the shale gas development in China, subsequently, the corresponding supporting policies were issued in the 12th Five-Year Plan. But from the experience in the US shale gas development, we know that the resulted environmental threats are always an unavoidable issue, but no uniform and standard evaluation system has yet been set up in China. The comprehensive environment refers to the combination of natural ecological environment and external macro-environment. In view of this, we conducted a series of studies on how to set up a comprehensive environmental impact assessment system as well as the related evaluation methodology and models. First, we made an in-depth investigation into shale gas development procedures and any possible environmental impacts, and then compared, screened and modified environmental impact assessment methods for shale gas development. Also, we established an evaluating system and assessment models according to different status of the above two types of environment: the correlation matrix method was employed to assess the impacts on natural ecological environment and the optimization distance method was modified to evaluate the impacts on external macro-environment. Finally, we substitute the two subindexes into the comprehensive environmental impact assessment model and achieved the final numerical result of environmental impact assessment. This model can be used to evaluate if a shale gas project has any impact on environment, compare the impacts before and after a shale gas development project, or the impacts of different projects.

Sweet spot identification in underexplored shales using multidisciplinary reservoir characterization and key performance indicators : Example of the Posidonia Shale Formation in the Netherlands

NARCIS (Netherlands)

Ter Heege, Jan; Zijp, Mart; Nelskamp, Susanne; Douma, Lisanne; Verreussel, Roel; Ten Veen, Johan; de Bruin, Geert; Peters, Rene

2015-01-01

Sweet spot identification in underexplored shale gas basins needs to be based on a limited amount of data on shale properties in combination with upfront geological characterization and modelling, because actual production data is usually absent. Multidisciplinary reservoir characterization and

Sweet spot identification in underexplored shales using multidisciplinary reservoir characterization and key performance indicators: example of the Posidonia Shale Formation in the Netherlands

NARCIS (Netherlands)

Heege, J.H. ter; Zijp, M.H.A.A.; Nelskamp, S.; Douma, L.A.N.R.; Verreussel, R.M.C.H.; Veen, J.H. ten; Bruin, G. de; Peters, M.C.A.M.

2015-01-01

Sweet spot identification in underexplored shale gas basins needs to be based on a limited amount of data on shale properties in combination with upfront geological characterization and modelling, because actual production data is usually absent. Multidisciplinary reservoir characterization and

Baseline groundwater quality from 34 wells in Wayne County, Pennsylvania, 2011 and 2013

Science.gov (United States)

Sloto, Ronald A.

2014-01-01

Wayne County, Pennsylvania, is underlain by the Marcellus Shale, which currently (2014) is being developed elsewhere in Pennsylvania for natural gas. All residents of largely rural Wayne County rely on groundwater for water supply, primarily from bedrock aquifers (shales and sandstones). This study, conducted by the U.S. Geological Survey in cooperation with the Pennsylvania Department of Conservation and Natural Resources, Bureau of Topographic and Geologic Survey (Pennsylvania Geological Survey), provides a groundwater-quality baseline for Wayne County prior to development of the natural gas resource in the Marcellus Shale. Selected wells completed in the Devonian-age Catskill Formation, undifferentiated; the Poplar Gap and Packerton Members of the Catskill Formation, undivided; and the Long Run and Walcksville Members of the Catskill Formation, undivided, were sampled.

A Reactive Transport Model for Marcellus Shale Weathering

Science.gov (United States)

Li, L.; Heidari, P.; Jin, L.; Williams, J.; Brantley, S.

2017-12-01

Shale formations account for 25% of the land surface globally. One of the most productive shale-gas formations is the Marcellus, a black shale that is rich in organic matter and pyrite. As a first step toward understanding how Marcellus shale interacts with water, we developed a reactive transport model to simulate shale weathering under ambient temperature and pressure conditions, constrained by soil chemistry and water data. The simulation was carried out for 10,000 years, assuming bedrock weathering and soil genesis began right after the last glacial maximum. Results indicate weathering was initiated by pyrite dissolution for the first 1,000 years, leading to low pH and enhanced dissolution of chlorite and precipitation of iron hydroxides. After pyrite depletion, chlorite dissolved slowly, primarily facilitated by the presence of CO2 and organic acids, forming vermiculite as a secondary mineral. A sensitivity analysis indicated that the most important controls on weathering include the presence of reactive gases (CO2 and O2), specific surface area, and flow velocity of infiltrating meteoric water. The soil chemistry and mineralogy data could not be reproduced without including the reactive gases. For example, pyrite remained in the soil even after 10,000 years if O2 was not continuously present in the soil column; likewise, chlorite remained abundant and porosity remained small with the presence of soil CO2. The field observations were only simulated successfully when the specific surface areas of the reactive minerals were 1-3 orders of magnitude smaller than surface area values measured for powdered minerals, reflecting the lack of accessibility of fluids to mineral surfaces and potential surface coating. An increase in the water infiltration rate enhanced weathering by removing dissolution products and maintaining far-from-equilibrium conditions. We conclude that availability of reactive surface area and transport of H2O and gases are the most important

Process of distilling bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Mayet, M

1859-05-19

This new process consists of placing at the end of a tube or the end of one or more retorts, an aspirating pump and compressor or a blower with two valves doing the same work or, better yet, a fan for sucking the vapor from the shale as it is formed in order to prevent its accumulating in the retorts and being decomposed. A second tube, pierced with little holes, placed in series with the pump, blower, or fan, acts as a vessel or receiver for the water. The vapors from the shale are compressed by the aspirator in the receiver for the water and condensed completely, without loss of gas and disinfect themselves for the most part.

Partial preservation of the Tentaculites Crotalinus shell from Ponta Grossa Formation (Devonian)

International Nuclear Information System (INIS)

Ciguel, J.H.G.; Roesler, O.

1988-01-01

This paper deals with an analysis of a single specimen of Tentaculites crotalinus SALTER emend. CIGUEL et al. (1984) that present a possible partial preservation of the shell. It comes from an outcrop of the Grossa Formation (Devonian) near Jaguariaiva, State of Parana. The skeletal microstructure of the Tentaculitoidea shell rather poorly Known. Thus, the phylogenetic relationships of these invertebrates still uncertain. Tentaculitids are very common fossils in Devonian Ponta Grossa Formation (Parana Basin) but so far Known only from external and internal moulds. The objective of this study is to demonstrate wheter the layer found in between the internal and external mould is or not a case shell preservation. The chemical composition of this layer and of the external mould was analysed by X rays. X rays difratometry was applied only to the matrix (at the external mould). The structure of the supposed shell remain was studied by binocular stereomicroscope and scanning electron microscope. It revealed a foliate structure due to several paralel to subparalel oriented lamelae, with a chemical composition distinct from the matrix, and some elements possibly mantained from the original shell composition. Thus, a partial preservation of the original shell seems to be the better explanation for this case. This shell would be composed by calcium carbonate disposed in laminar layers, the outer ones being impregnated by Fe and Mn molecules during the diagenetic processes. The skeletal composition and microstructure would suggest a molluscan affinity for the tentaculitida Order. (auThor) [pt

Results of chemical analyses of soil, shale, and soil/shale extract from the Mancos Shale formation in the Gunnison Gorge National Conservation Area, southwestern Colorado, and at Hanksville, Utah

Science.gov (United States)

Tuttle, Michele L.W.; Fahy, Juli; Grauch, Richard I.; Ball, Bridget A.; Chong, Geneva W.; Elliott, John G.; Kosovich, John J.; Livo, Keith E.; Stillings, Lisa L.

2007-01-01

Results of chemical and some isotopic analyses of soil, shale, and water extracts collected from the surface, trenches, and pits in the Mancos Shale are presented in this report. Most data are for sites on the Gunnison Gorge National Conservation Area (GGNCA) in southwestern Colorado. For comparison, data from a few sites from the Mancos landscape near Hanksville, Utah, are included. Twelve trenches were dug on the GGNCA from which 258 samples for whole-rock (total) analyses and 187 samples for saturation paste extracts were collected. Sixteen of the extract samples were duplicated and subjected to a 1:5 water extraction for comparison. A regional soil survey across the Mancos landscape on the GGNCA generated 253 samples for whole-rock analyses and saturation paste extractions. Seventeen gypsum samples were collected on the GGNCA for sulfur and oxygen isotopic analysis. Sixteen samples were collected from shallow pits in the Mancos Shale near Hanksville, Utah.

Role of spent shale in oil shale processing and the management of environmental residues. Final technical report, January 1979-May 1980

Energy Technology Data Exchange (ETDEWEB)

Hines, A.L.

1980-08-15

The adsorption of hydrogen sulfide on retorted oil shale was studied at 10, 25, and 60/sup 0/C using a packed bed method. Equilibrium isotherms were calculated from the adsorption data and were modeled by the Langmuir, Freundlich, and Polanyi equations. The isosteric heat of adsorption was calculated at three adsorbent loadings and was found to increase with increased loading. A calculated heat of adsorption less than the heat of condensation indicated that the adsorption was primarily due to Van der Waals' forces. Adsorption capacities were also found as a function of oil shale retorting temperature with the maximum uptake occurring on shale that was retorted at 750/sup 0/C.

Shale disposal of U.S. high-level radioactive waste.

Energy Technology Data Exchange (ETDEWEB)

Sassani, David Carl; Stone, Charles Michael; Hansen, Francis D.; Hardin, Ernest L.; Dewers, Thomas A.; Martinez, Mario J.; Rechard, Robert Paul; Sobolik, Steven Ronald; Freeze, Geoffrey A.; Cygan, Randall Timothy; Gaither, Katherine N.; Holland, John Francis; Brady, Patrick Vane

2010-05-01

This report evaluates the feasibility of high-level radioactive waste disposal in shale within the United States. The U.S. has many possible clay/shale/argillite basins with positive attributes for permanent disposal. Similar geologic formations have been extensively studied by international programs with largely positive results, over significant ranges of the most important material characteristics including permeability, rheology, and sorptive potential. This report is enabled by the advanced work of the international community to establish functional and operational requirements for disposal of a range of waste forms in shale media. We develop scoping performance analyses, based on the applicable features, events, and processes identified by international investigators, to support a generic conclusion regarding post-closure safety. Requisite assumptions for these analyses include waste characteristics, disposal concepts, and important properties of the geologic formation. We then apply lessons learned from Sandia experience on the Waste Isolation Pilot Project and the Yucca Mountain Project to develop a disposal strategy should a shale repository be considered as an alternative disposal pathway in the U.S. Disposal of high-level radioactive waste in suitable shale formations is attractive because the material is essentially impermeable and self-sealing, conditions are chemically reducing, and sorption tends to prevent radionuclide transport. Vertically and laterally extensive shale and clay formations exist in multiple locations in the contiguous 48 states. Thermal-hydrologic-mechanical calculations indicate that temperatures near emplaced waste packages can be maintained below boiling and will decay to within a few degrees of the ambient temperature within a few decades (or longer depending on the waste form). Construction effects, ventilation, and the thermal pulse will lead to clay dehydration and deformation, confined to an excavation disturbed zone within

A comprehensive environmental impact assessment method for shale gas development

OpenAIRE

Sun, Renjin; Wang, Zhenjie

2015-01-01

The great success of US commercial shale gas exploitation stimulates the shale gas development in China, subsequently, the corresponding supporting policies were issued in the 12th Five-Year Plan. But from the experience in the US shale gas development, we know that the resulted environmental threats are always an unavoidable issue, but no uniform and standard evaluation system has yet been set up in China. The comprehensive environment refers to the combination of natural ecological environm...

The Geopolitical Impact of Shale Gas : The Modelling Approach

NARCIS (Netherlands)

Auping, W.L.; De Jong, S.; Pruyt, E.; Kwakkel, J.H.

2014-01-01

The US’ shale gas revolution, a spectacular increase in natural gas extraction from previously unconventional sources, has led to considerable lower gas prices in North America. This study focusses on consequences of the shale gas revolution on state stability of traditional oil and gas exporting

Residential radon in Kansas City-black shales aren't the prime suspect

International Nuclear Information System (INIS)

Spencer, C.G.

1993-01-01

The US EPA preliminary assessment of potential radon risk (EPA, 1986) depicted a large area of the mid-continent in which radon levels might be elevated due to the presence of uranium-rich black shales. A preliminary study (Hilpman, Coveney ampersand Spencer, 1988) indicated that a significant percentage of homes in the greater Kansas City area had radon screening levels above 4 pCi/L. However, their lab tests with crushed black shale, and radon tests in limestone mines with black shale floors showed that the shale did not yield extremely high radon levels. This expanded study presents additional results of screening tests in homes, and correlates those results to bedrock geology and soil type. High radon levels in the Kansas city area are not due primarily to black shale sources. The highest readings are associated with limestone and non-organic shale. Mean radon level is higher in younger cyclothemic deposits, and a loessial soil. The EPA initial assessment overstated the radon risk attributable to black uraniferous shale sources. Assessment of the overall potential risk for the greater Kansas City area requires further evaluation of other sources

Coupled Fracture and Flow in Shale in Hydraulic Fracturing

Science.gov (United States)

Carey, J. W.; Mori, H.; Viswanathan, H.

2014-12-01

Production of hydrocarbon from shale requires creation and maintenance of fracture permeability in an otherwise impermeable shale matrix. In this study, we use a combination of triaxial coreflood experiments and x-ray tomography characterization to investigate the fracture-permeability behavior of Utica shale at in situ reservoir conditions (25-50 oC and 35-120 bars). Initially impermeable shale core was placed between flat anvils (compression) or between split anvils (pure shear) and loaded until failure in the triaxial device. Permeability was monitored continuously during this process. Significant deformation (>1%) was required to generate a transmissive fracture system. Permeability generally peaked at the point of a distinct failure event and then dropped by a factor of 2-6 when the system returned to hydrostatic failure. Permeability was very small in compression experiments (fashion as pressure increased. We also observed that permeability decreased with increasing fluid flow rate indicating that flow did not follow Darcy's Law, possibly due to non-laminar flow conditions, and conformed to Forscheimer's law. The coupled deformation and flow behavior of Utica shale, particularly the large deformation required to initiate flow, indicates the probable importance of activation of existing fractures in hydraulic fracturing and that these fractures can have adequate permeability for the production of hydrocarbon.

Release of Particulate Iron Sulfide during Shale-Fluid Interaction.

Science.gov (United States)

Kreisserman, Yevgeny; Emmanuel, Simon

2018-01-16

During hydraulic fracturing, a technique often used to extract hydrocarbons from shales, large volumes of water are injected into the subsurface. Although the injected fluid typically contains various reagents, it can become further contaminated by interaction with minerals present in the rocks. Pyrite, which is common in organic-rich shales, is a potential source of toxic elements, including arsenic and lead, and it is generally thought that for these elements to become mobilized, pyrite must first dissolve. Here, we use atomic force microscopy and environmental scanning electron microscopy to show that during fluid-rock interaction, the dissolution of carbonate minerals in Eagle Ford shale leads to the physical detachment, and mobilization, of embedded pyrite grains. In experiments carried out over a range of pH, salinity, and temperature we found that in all cases pyrite particles became detached from the shale surfaces. On average, the amount of pyrite detached was equivalent to 6.5 × 10 -11 mol m -2 s -1 , which is over an order of magnitude greater than the rate of pyrite oxidation expected under similar conditions. This result suggests that mechanical detachment of pyrite grains could be an important pathway for the mobilization of arsenic in hydraulic fracturing operations and in groundwater systems containing shales.

Study on Shale Adsorption Equation Based on Monolayer Adsorption, Multilayer Adsorption, and Capillary Condensation

OpenAIRE

Chen, Qing; Tian, Yuanyuan; Li, Peng; Yan, Changhui; Pang, Yu; Zheng, Li; Deng, Hucheng; Zhou, Wen; Meng, Xianghao