Initial investigations of (np)-scattering with a polarized deuterium target at ANKE-COSY

Energy Technology Data Exchange (ETDEWEB)

Gou, Boxing

2015-07-01

The understanding of the forces among nucleons is fundamental to the whole of nuclear and hadronic physics. The nucleon-nucleon (NN) scattering is the ideal probe to study the nuclear forces. The scattering amplitudes for the complete description of the NN interactions can be reconstructed from phase-shift analyses (PSA), which requires measurements with polarized experiments. The existing data allow to extract unambiguous proton-proton (pp) amplitudes below 2 GeV. However, there is very little known about the neutron-proton (np) system above 800 MeV nucleon energy. THE ANKE-COSY collaboration has embarked on a systematic program which aims to extract the np scattering amplitudes through the deuteron-proton charge-exchange process dp→{pp}{sub s}n. First part of the program via polarized deuteron beam and hydrogen target allowed successful measurement of np amplitudes up to 1.135 GeV nucleon energy, which is the maximum nucleon energy that can be accessed with deuteron beam at COSY. Via inverse kinematics, i.e. using a proton beam incident on a polarized deuterium target will allow to enhance the np study up to 2.8 GeV, the highest energy available at COSY. The method of inverse kinematics has to be validated prior to the production experiment. As the proof-of-principle (POP) experiment, the initial research has been conducted at proton energy T{sub p}=600 MeV using a polarized deuterium target. The projectiles were measured by two silicon tracking telescopes (STT) placed closed to the target and by the ANKE sub-detection systems. Four polarization modes of the deuterium target were employed. In order to increase the effective target thickness, polarized deuterium atoms produced by the atomic beam source (ABS) was filled into a storage cell, where the circulating COSY beam collides with the target. The target polarizations were measured using the proton-deuteron elastic reaction. The vector and tensor analyzing powers A{sub y} and A{sub yy} of pvector d�

Feasibility study of electron-scattering experiments with a tensor-polarized deuterium target in an electron storage ring

International Nuclear Information System (INIS)

Holt, R.J.; Geesaman, D.F.; Goodman, L.S.

1985-01-01

The feasibility of using a spin-exchange optical-pumping method to produce a high flux of tensor-polarized deuterium atoms is being tested. In this method, alkali atoms are polarized by optical pumping and the polarization is transferred to deuterium by successive spin-exchange collisions. In a test with a simple model the authors achieved 10 mW of laser power absorbed to the spin-exchange process with deuterium. Construction of a more sophisticated prototype was completed and tests are in progress. Dissociation fractions in excess of 80% for deuterium molecules have been achieved thus far. In order to optimize the performance of the prototype target, a computerized model of the target was constructed. A section of a differential-pumping system was constructed and tested. It was possible to sustain more than the required 5 orders-of-magnitude pressure drop in a distance of approximately 1.5 m

Energy cost of negative pion production on deuterium-tritium target

Energy Technology Data Exchange (ETDEWEB)

Kuzminov, V.V. (Petersburg Nuclear Physics Inst., Gatchina, St. Petersburg (Russian Federation)); Petrov, Yu.V. (Petersburg Nuclear Physics Inst., Gatchina, St. Petersburg (Russian Federation)); Shabelski, Yu.M. (Petersburg Nuclear Physics Inst., Gatchina, St. Petersburg (Russian Federation))

1993-12-01

The negative pion production by deuterons (T[sub 0] = 0.8 GeV/nucl.) was calculated for a cylindrical gaseous deuterium-tritium target (the density of DT-mixture is [phi] = 0.5). Revised cross sections of nucleon-nucleus interaction were used in a Monte Carlo simulation and multiple nucleon-nuclei collisions were taken into account. The energy cost of negative pion production is [epsilon][sub [pi][sup -

Hot muonic deuterium and tritium from cold targets

International Nuclear Information System (INIS)

Marshall, G.M.; Beveridge, J.L.; Bailey, J.M.; Beer, G.A.; Knowles, P.E.; Mason, G.R.; Olin, A.; Brewer, J.H.; Forster, B.M.; Huber, T.M.; Pippitt, B.; Jacot-Guillarmod, R.; Schellenberg, L.; Martoff, C.J.; Petitjean, C.

1992-01-01

Experiments are described which use a solid hydrogen layer to form muonic hydrogen isotopes in vacuum. The method relies on transfer of the muon from protium to either a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections, and may be emitted from the surface of the layer. Measurements which detect decay electrons, muonic x-rays, and fusion products have been used to study the processes. A target has been constructed which exploits muonic atom emission in order to study the energy dependence of transfer and muon molecular formation

A polarized hydrogen/deuterium atomic beam source for internal target experiments

International Nuclear Information System (INIS)

Szczerba, D.; Buuren, L.D. van; Brand, J.F.J. van den; Bulten, H.J.; Ferro-Luzzi, M.; Klous, S.; Kolster, H.; Lang, J.; Mul, F.; Poolman, H.R.; Simani, M.C.

2000-01-01

A high-brightness hydrogen/deuterium atomic beam source is presented. The apparatus, previously used in electron scattering experiments with tensor-polarized deuterium (Ferro-Luzzi et al., Phys. Rev. Lett. 77 (1996) 2630; van den Brand et al., Phys. Rev. Lett. 78 (1997) 1235; Zhou et al., Phys. Rev. Lett. 82 (1998) 687; Bouwhuis et al., Phys. Rev. Lett. 82 (1999) 3755), was configured as a source for internal target experiments to measure single- and double-polarization observables, with either polarized hydrogen or vector/tensor polarized deuterium. The atomic beam intensity was enhanced by a factor of ∼2.5 by optimizing the Stern-Gerlach focusing system using high tip-field (∼1.5 T) rare-earth permanent magnets, and by increasing the pumping speed in the beam-formation chamber. Fluxes of (5.9±0.2)x10 16 1 H/s were measured in a diameter 12 mmx122 mm compression tube with its entrance at a distance of 27 cm from the last focusing element. The total output flux amounted to (7.6±0.2)x10 16 1 H/s

A highly polarized hydrogen/deuterium internal gas target embedded in a toroidal magnetic spectrometer

International Nuclear Information System (INIS)

Cheever, D.; Ihloff, E.; Kelsey, J.; Kolster, H.; Meitanis, N.; Milner, R.; Shinozaki, A.; Tsentalovich, E.; Zwart, T.; Ziskin, V.; Xiao, Y.; Zhang, C.

2006-01-01

A polarized hydrogen/deuterium internal gas target has been constructed and operated at the internal target region of the South Hall Ring (SHR) of the MIT-Bates Linear Accelerator Center to carry out measurements of spin-dependent electron scattering at 850MeV. The target used an Atomic Beam Source (ABS) to inject a flux of highly polarized atoms into a thin-walled, coated storage cell. The polarization of the electron beam was determined using a Compton laser backscattering polarimeter. The target polarization was determined using well-known nuclear reactions. The ABS and storage cell were embedded in the Bates Large Acceptance Toroidal Spectrometer (BLAST), which was used to detect scattered particles from the electron-target interactions. The target has been designed to rapidly (∼8h) switch operation from hydrogen to deuterium. Further, this target was the first to be operated inside a magnetic spectrometer in the presence of a magnetic field exceeding 2kG. An ABS intensity 2.5x10 16 at/s and a high polarization (∼70%) inside the storage cell have been achieved. The details of the target design and construction are described here and the performance over an 18 month period is reported

Optimization of a liquid hydrogen/deuterium target with extremely thin foil windows

International Nuclear Information System (INIS)

Nake, C.J.

1993-09-01

For external experiments at COSY a target of liquid hydrogen or deuterium has been developed, which is very small in order to take advantage of the excellent beam quality of COSY. Targets with thicknesses down to only mm's have been built and operate without bubbles. In order to make the effects of reactions in the windows much smaller than the target reactions, windows with a thickness of about 1.5 μm have been achieved. A novel system which stabilizes the pressure difference between the inside and the outside of the target cell to a small constant value under all target conditions is used. (orig.)

Spin exchange in polarized deuterium

International Nuclear Information System (INIS)

Przewoski, B. von; Meyer, H.O.; Balewski, J.; Doskow, J.; Ibald, R.; Pollock, R.E.; Rinckel, T.; Wellinghausen, A.; Whitaker, T.J.; Daehnick, W.W.; Haeberli, W.; Schwartz, B.; Wise, T.; Lorentz, B.; Rathmann, F.; Pancella, P.V.; Saha, Swapan K.; Thoerngren-Engblom, P.

2003-01-01

We have measured the vector and tensor polarization of an atomic deuterium target as a function of the target density. The polarized deuterium was produced in an atomic beam source and injected into a storage cell. For this experiment, the atomic beam source was operated without rf transitions, in order to avoid complications from the unknown efficiency of these transitions. In this mode, the atomic beam is vector and tensor polarized and both polarizations can be measured simultaneously. We used a 1.2-cm-diam and 27-cm-long storage cell, which yielded an average target density between 3 and 9x10 11 at/cm 3 . We find that the tensor polarization decreases with increasing target density while the vector polarization remains constant. The data are in quantitative agreement with the calculated effect of spin exchange between deuterium atoms at low field

Development of high pressure deuterium gas targets for the generation of intense mono-energetic fast neutron beams

International Nuclear Information System (INIS)

Guzek, J.; Richardson, K.; Franklyn, C.B.; Waites, A.; McMurray, W.R.; Watterson, J.I.W.; Tapper, U.A.S.

1999-01-01

Two different technical solutions to the problem of generation of mono-energetic fast neutron beams on the gaseous targets are presented here. A simple and cost-effective design of a cooled windowed gas target system is described in the first part of this paper. It utilises a thin metallic foil window and circulating deuterium gas cooled down to 100 K. The ultimate beam handling capability of such target is determined by the properties of the window. Reliable performance of this gas target system was achieved at 1 bar of deuterium gas, when exposed to a 45 μA beam of 5 MeV deuterons, for periods in excess of 6 h. Cooling of the target gas resulted in increased fast neutron output and improved neutron to gamma-ray ratio. The second part of this paper discusses the design of a high pressure, windowless gas target for use with pulsed, low duty cycle accelerators. A rotating seal concept was applied to reduce the gas load in a differentially pumped system. This allows operation at 1.23 bar of deuterium gas pressure in the gas cell region. Such a gas target system is free from the limitations of the windowed target but special attention has to be paid to the heat dissipation capability of the beam dump, due to the use of a thin target. The rotating seal concept is particularly suitable for use with accelerators such as radio-frequency quadrupole (RFQ) linacs that operate with a very high peak current at low duty cycle. The performance of both target systems was comprehensively characterized using the time-of-flight (TOF) technique. This demonstrated that very good quality mono-energetic fast neutron beams were produced with the slow neutron and gamma-ray component below 10% of the total target output

Deeply Virtual Compton Scattering off a deuterium target at the HERMES experiment

International Nuclear Information System (INIS)

Movsisyan, Aram

2011-05-01

Deeply virtual Compton scattering is studied in this report, using all data collected at the HERMES experiment from 1996 to 2005. Azimuthal asymmetries with respect to beam-helicity, beam-charge and target polarization alone and also to their different combinations for hard exclusive electroproduction of real photons in deep-inelastic scattering from a both unpolarized and longitudinally polarized deuterium targets are measured. The asymmetries are attributed to the interference between the deeply virtual Compton scattering and Bethe-Heitler processes. The asymmetries are observed in the exclusive region -(1.5) 2 GeV 2 2 X 2 GeV 2 of the squared missing mass. The dependences of these asymmetries on -t, x N , or Q 2 are investigated. The results include the coherent process ed→edγ and the incoherent process ed→epnγ where in addition a nucleon may be excited to a resonance. For an unpolarized deuterium target, the leading Fourier amplitude of the beam-helicity asymmetry that is sensitive to the interference term is found to be substantial, but no significant t dependence is observed. The leading amplitude of the beam-charge asymmetry is substantial at large -t, but becomes small at small values of -t. The amplitudes of the beam-helicity asymmetry that are sensitive to the squared DVCS term are found to be consistent with zero. The deuteron Compton form factor H 1 appears to have a similar behavior as H of the proton. (orig.)

Θ"+ search at HERMES with deuterium and hydrogen targets

International Nuclear Information System (INIS)

Wang Siguang; Schnell, Gunar

2016-01-01

The previous search at HERMES for narrow baryon states excited in quasi-real photo-production, decaying through the channel Θ"+ → pK_S"0 → pπ"+ π"-, has been extended. Improved decay-particle reconstruction, more advanced particle identification, and increased event samples are employed. The structure that was observed earlier at an invariant mass of 1528 MeV shifts to 1522 MeV in the new analysis of data with a deuterium target, with a drop of statistical significance to about 2σ. The number of events above background is 68_-_3_1"+"9"8(stat)±13(sys). No such structure is observed in the hydrogen data set. (author)

Laser ``M'egajoule'' cryogenic target program: from target fabrication to conformation of the deuterium-tritium ice layer

Science.gov (United States)

Collier, Rémy; Durut, Frédéric; Reneaume, Benoît; Chicane, Cédric; Théobald, Marc; Breton, Olivier; Martin, Michel; Fleury, Emmanuel; Vincent-Viry, Olivier; Bachelet, Franck; Jeannot, Laurent; Geoffray, Isabelle; Botrel, Ronan; Dauteuil, Christophe; Hermerel, Cyril; Choux, Alexandre; Bednarczyk, Sophie; Legaie, Olivier

2008-11-01

For the French inertial confinement fusion (ICF) experiments, cryogenic target assemblies (CTAs) for the LMJ program are manufactured and filled at CEA Valduc (Dijon) in the cryogenic targets filling station (IRCC). They will be moved at about 20 K into a transport cryostat for cryogenic targets and will be driven from CEA/Valduc to CEA/CESTA (Bordeaux). Cryogenic targets will then be transferred by several cryogenic grippers on the cryogenic target positioner before shots. The CTA has to meet severe specifications and involves a lot of challenging tasks for its manufacture. To fill CTAs by permeation with deuterium-tritium (DT), the IRCC need to meet strict thermal, mechanical and dimensional specifications. To obtain a good combustion yield, a very homogenous DT ice layer and very smooth roughness at 1.5 K below the DT triple point are also required. This paper deals with the up to date main issues in the different fields of the LMJ cryogenic target program.

Ex-vacuo nuclear reaction analysis of deuterium

International Nuclear Information System (INIS)

Lee, S.R.; Doyle, B.L.

1989-01-01

A novel technique for performing in-air d( 3 He, p) nuclear reaction analysis of deuterium using external 3 He ion beams ranging in energy from 0.3-2.0 MeV is presented. Variable on-target beam energies for the depth profiling of deuterium are obtained by varying the transmission distance of the external 3 He beam in air. The ex-vacuo nuclear reaction analysis (XNRA) apparatus is described, and unique aspects and limitations of in-air depth profiling of deuterium using the d( 3 He, p) reaction are discussed. Example analyses where XNRA has been used for the multidimensional measurement of deuterium in fusion reactor components are presented in order to illustrate the advantages of XNRA for deuterium. These advantages include nondestructive analysis of large targets, efficient depth profiling via variable air gap energy tuning, and rapid analysis of numerous samples in the absence of vacuum cycling. (orig.)

Deeply Virtual Compton Scattering off a deuterium target at the HERMES experiment

Energy Technology Data Exchange (ETDEWEB)

Movsisyan, Aram

2011-05-15

Deeply virtual Compton scattering is studied in this report, using all data collected at the HERMES experiment from 1996 to 2005. Azimuthal asymmetries with respect to beam-helicity, beam-charge and target polarization alone and also to their different combinations for hard exclusive electroproduction of real photons in deep-inelastic scattering from a both unpolarized and longitudinally polarized deuterium targets are measured. The asymmetries are attributed to the interference between the deeply virtual Compton scattering and Bethe-Heitler processes. The asymmetries are observed in the exclusive region -(1.5){sup 2} GeV{sup 2}deuterium target, the leading Fourier amplitude of the beam-helicity asymmetry that is sensitive to the interference term is found to be substantial, but no significant t dependence is observed. The leading amplitude of the beam-charge asymmetry is substantial at large -t, but becomes small at small values of -t. The amplitudes of the beam-helicity asymmetry that are sensitive to the squared DVCS term are found to be consistent with zero. The deuteron Compton form factor H{sub 1} appears to have a similar behavior as H of the proton. (orig.)

Relativistic description of the Fermi motion effects on deuterium targets

International Nuclear Information System (INIS)

Kusno, D.

1979-12-01

A comprehensive analysis of the inconsistencies of the conventional, non-relativistic approach, which has been used so far in the extraction of neutron data from deuterium targets, is given. A new approach dealing with the smearing effects, due to the nucleon's Fermi motion inside the deuteron, is developed as an alternative to the conventional one. This new approach is a spin-less, relativistic, simple and consistent approach. A new covariant model of the elastic electromagnetic form factors of the deuteron in the impulse approximation is also presented. The treatment includes spin and allows for a possibility of determining completely the two elastic structure functions

Influence of tungsten microstructure and ion flux on deuterium plasma-induced surface modifications and deuterium retention

NARCIS (Netherlands)

Buzi, L.; De Temmerman, G.; Unterberg, B.; M. Reinhart,; Dittmar, T.; Matveev, D.; Linsmeier, C.; Breuer, U.; Kreter, A.; Van Oost, G.

2015-01-01

The influence of surface temperature, particle flux density and material microstructure on the surface morphology and deuterium retention was studied by exposing tungsten targets (20 μm and 40 μm grain size) to deuterium plasma at the same particle fluence (1026 m−2) and

Numerical studies of deuterium-tritium ignition in impact-fusion targets

International Nuclear Information System (INIS)

Zubrin, R.M.; Ribe, F.L.

1989-01-01

A numerical one-dimensional solution of the Euler equations for an imploding spherical tungsten shell with internal deuterium-tritium gas is applied to study impact-fusion dynamics with parameters of fusion reactor relevance. Thermal conduction and radiative energy loss by the plasma are taken into account, as is heating by fusion generated alpha particles. A variety of target sizes and impact velocities are examined, and scaling laws for fusion yields are deduced which define possible parameters for conceptual commercial impact-fusion power reactors. It is found that shell energies and velocities of about 30 MJ and 110 km/s would be satisfactory. A commercial impact-fusion reactor based on such parameters is discussed

Compression of a spherically symmetric deuterium-tritium plasma liner onto a magnetized deuterium-tritium target

International Nuclear Information System (INIS)

Santarius, J. F.

2012-01-01

Converging plasma jets may be able to reach the regime of high energy density plasmas (HEDP). The successful application of plasma jets to magneto-inertial fusion (MIF) would heat the plasma by fusion products and should increase the plasma energy density. This paper reports the results of using the University of Wisconsin’s 1-D Lagrangian, radiation-hydrodynamics, fusion code BUCKY to investigate two MIF converging plasma jet test cases originally analyzed by Samulyak et al.[Physics of Plasmas 17, 092702 (2010)]. In these cases, 15 cm or 5 cm radially thick deuterium-tritium (DT) plasma jets merge at 60 cm from the origin and converge radially onto a DT target magnetized to 2 T and of radius 5 cm. The BUCKY calculations reported here model these cases, starting from the time of initial contact of the jets and target. Compared to the one-temperature Samulyak et al. calculations, the one-temperature BUCKY results show similar behavior, except that the plasma radius remains about twice as long near maximum compression. One-temperature and two-temperature BUCKY results differ, reflecting the sensitivity of the calculations to timing and plasma parameter details, with the two-temperature case giving a more sustained compression.

High pressure deuterium-tritium gas target vessels for muon-catalyzed fusion experiments

International Nuclear Information System (INIS)

Caffrey, A.J.; Spaletta, H.W.; Ware, A.G.; Zabriskie, J.M.; Hardwick, D.A.; Maltrud, H.R.; Paciotti, M.A.

1989-01-01

In experimental studies of muon-catalyzed fusion, the density of the hydrogen gas mixture is an important parameter. Catalysis of up to 150 fusions per muon has been observed in deuterium-tritium gas mixtures at liquid hydrogen density; at room temperature, such densities require a target gas pressure of the order of 1000 atmospheres (100 MPa, 15,000 psi). We report here the design considerations for hydrogen gas target vessels for muon-catalyzed fusion experiments that operate at 1000 and 10,000 atmospheres. The 1000 atmosphere high pressure target vessels are fabricated of Type A-286 stainless steel and lined with oxygen-free, high-conductivity (OFHC) copper to provide a barrier to hydrogen permeation of the stainless steel. The 10,000 atmosphere ultrahigh pressure target vessels are made from 18Ni (200 grade) maraging steel and are lined with OFHC copper, again to prevent hydrogen permeation of the steel. In addition to target design features, operating requirements, fabrication procedures, and secondary containment are discussed. 13 refs., 3 figs., 1 tab

A Gamma Polarimeter for Neutron Polarization Measurement in a Liquid Deuterium Target for Parity Violation in Polarized Neutron Capture on Deuterium.

Science.gov (United States)

Komives, A; Sint, A K; Bowers, M; Snow, M

2005-01-01

A measurement of the parity-violating gamma asymmetry in n-D capture would yield information on N-N parity violation independent of the n-p system. Since cold neutrons will depolarize in a liquid deuterium target in which the scattering cross section is much larger than the absorption cross section, it will be necessary to quantify the loss of polarization before capture. One way to do this is to use the large circular polarization of the gamma from n-D capture and analyze the circular polarization of the gamma in a gamma polarimeter. We describe the design of this polarimeter.

The HERMES polarized hydrogen and deuterium gas target in the HERA electron storage ring

International Nuclear Information System (INIS)

Airapetian, A.; Akopov, N.; Akopov, Z.

2005-01-01

The HERMES hydrogen and deuterium nuclear-polarized gas targets have been in use since 1996 with the polarized electron beam of HERA at DESY to study the spin structure of the nucleon. Polarized atoms from a Stern-Gerlach Atomic Beam Source are injected into a storage cell internal to the HERA electron ring. Atoms diffusing from the center of the storage cell into a side tube are analyzed to determine the atomic fraction and the atomic polarizations. The atoms have a nuclear polarization, the axis of which is defined by an external magnetic holding field. The holding field was longitudinal during 1996-2000, and was changed to transverse in 2001. The design of the target is described, the method for analyzing the target polarization is outlined, and the performance of the target in the various running periods is presented

The HERMES polarized hydrogen and deuterium gas target in the HERA electron storage ring

International Nuclear Information System (INIS)

Airapetian, A.; Akopov, N.; Akopov, Z.; Peking University, Beijing

2004-08-01

The HERMES hydrogen and deuterium nuclear-polarized gas targets have been in use since 1996 with the polarized electron beam of HERA at DESY to study the spin structure of the nucleon. Polarized atoms from a Stern-Gerlach Atomic Beam Source are injected into a storage cell internal to the HERA electron ring. Atoms diffusing from the center of the storage cell into a side tube are analyzed to determine the atomic fraction and the atomic polarizations. The atoms have a nuclear polarization, the axis of which is defined by an external magnetic holding field. The holding field was longitudinal during 1996-2000, and was changed to transverse in 2001. The design of the target is described, the method for analyzing the target polarization is outlined, and the performance of the target in the various running periods is presented. (orig.)

Design of a deuterium and tritium-ablator shock ignition target for the National Ignition Facility

International Nuclear Information System (INIS)

Terry, Matthew R.; Perkins, L. John; Sepke, Scott M.

2012-01-01

Shock ignition presents a viable path to ignition and high gain on the National Ignition Facility (NIF). In this paper, we describe the development of the 1D design of 0.5 MJ class, all-deuterium and tritium (fuel and ablator) shock ignition target that should be reasonably robust to Rayleigh-Taylor fluid instabilities, mistiming, and hot electron preheat. The target assumes “day one” NIF hardware and produces a yield of 31 MJ with reasonable allowances for laser backscatter, absorption efficiency, and polar drive power variation. The energetics of polar drive laser absorption require a beam configuration with half of the NIF quads dedicated to launching the ignitor shock, while the remaining quads drive the target compression. Hydrodynamic scaling of the target suggests that gains of 75 and yields 70 MJ may be possible.

Absence of molecular deuterium dissociation during room-temperature permeation into polystyrene ICF target shells

International Nuclear Information System (INIS)

Honig, A.; Alexander, N.; Fan, Q.; Gram, R.; Kim, H.

1991-01-01

Polystyrene microshells filled with deuterium and tritium gas are important target shells for inertially confined fusion (ICF) and are particularly promising for target containing spin-polarized hydrogens fuels. A currently active approach to the latter uses polarized D in HD, in a method which requires preservation of the high purity of the initially prepared HD (very low specified H 2 and D 2 concentrations). This would not be possible if dissociation should occur during permeation into the target shells. We have thus tested polystyrene shells using a novel method which employs very pure polystyrene shells using a novel method which employs very pure ortho-D 2 as the test gas. An upper limit of 6 x 10 -4 was deduced for the dissociation of D 2 upon room temperature permeation through an approximately 8 um wall of polystyrene, clearing the way for use of polystyrene target shells for ICF fusion experiments with spin-polarized hydrogens fuels. 19 refs., 1 fig

Tests of a polarized source of hydrogen and deuterium based on spin-exchange optical pumping and a storage cell for polarized deuterium

International Nuclear Information System (INIS)

Holt, R.J.; Gilman, R.; Kinney, E.R.

1988-01-01

A novel laser-driven polarized source of hydrogen and deuterium which is based on the principle of spin-exchange optical pumping has been developed at Argonne. The advantages of this method over conventional polarized sources for internal target experiments is discussed. At present, the laser-driven polarized source delivers hydrogen 8 x 10 16 atoms/s with a polarization of 24% and deuterium at 6 x 10 16 atoms/s with a polarization of 25%. A passive storage cell for polarized deuterium was tested in the VEPP-3 electron storage ring. The storage cell was found to increase the target thickness by approximately a factor of three and no loss in polarization was observed. 10 refs., 4 figs., 2 tabs

Effect of noble gas ion pre-irradiation on deuterium retention in tungsten

NARCIS (Netherlands)

Cheng, L.; Zhao, Z. H.; De Temmerman, G.; Yuan, Y.; Morgan, T. W.; Guo, L. P.; Wang, B.; Zhang, Y.; Wang, B. Y.; Zhang, P.; Cao, X. Z.; Lu, G. H.

2016-01-01

Impurity seeding of noble gases is an effective way of decreasing the heat loads onto the divertor targets in fusion devices. To investigate the effect of noble gases on deuterium retention, tungsten targets have been implanted by different noble gas ions and subsequently exposed to deuterium

Selective deuterium ion acceleration using the Vulcan petawatt laser

Energy Technology Data Exchange (ETDEWEB)

Krygier, A. G. [Laboratoire pour l' Utilisation des Lasers Intenses, École Polytechnique, 91128 Palasiseau (France); Physics Department, The Ohio State University, Columbus, Ohio 43210 (United States); Morrison, J. T. [Propulsion Systems Directorate, Air Force Research Lab, Wright Patterson Air Force Base, Ohio 45433 (United States); Kar, S., E-mail: s.kar@qub.ac.uk; Ahmed, H.; Alejo, A.; Green, A.; Jung, D. [Centre for Plasma Physics, School of Mathematics and Physics, Queens University Belfast, Belfast BT7 1NN (United Kingdom); Clarke, R.; Notley, M. [Central Laser Facility, Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Fuchs, J.; Vassura, L. [Laboratoire pour l' Utilisation des Lasers Intenses, École Polytechnique, 91128 Palasiseau (France); Kleinschmidt, A.; Roth, M. [Institut für Kernphysik, Technische Universität Darmstadt, Schloßgartenstrasse 9, D-64289 Darmstadt (Germany); Najmudin, Z.; Nakamura, H. [The John Adams Institute, Blackett Laboratory, Department of Physics, Imperial College, London SW7 2AZ (United Kingdom); Norreys, P. [Central Laser Facility, Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Department of Physics, University of Oxford, Oxford OX1 3PU (United Kingdom); Oliver, M. [Department of Physics, University of Oxford, Oxford OX1 3PU (United Kingdom); Zepf, M. [Centre for Plasma Physics, School of Mathematics and Physics, Queens University Belfast, Belfast BT7 1NN (United Kingdom); Helmholtz Institute Jena, D-07743 Jena (Germany); Borghesi, M. [Centre for Plasma Physics, School of Mathematics and Physics, Queens University Belfast, Belfast BT7 1NN (United Kingdom); Institute of Physics of the ASCR, ELI-Beamlines Project, Na Slovance 2, 18221 Prague (Czech Republic); Freeman, R. R. [Physics Department, The Ohio State University, Columbus, Ohio 43210 (United States)

2015-05-15

We report on the successful demonstration of selective acceleration of deuterium ions by target-normal sheath acceleration (TNSA) with a high-energy petawatt laser. TNSA typically produces a multi-species ion beam that originates from the intrinsic hydrocarbon and water vapor contaminants on the target surface. Using the method first developed by Morrison et al. [Phys. Plasmas 19, 030707 (2012)], an ion beam with >99% deuterium ions and peak energy 14 MeV/nucleon is produced with a 200 J, 700 fs, >10{sup 20}W/cm{sup 2} laser pulse by cryogenically freezing heavy water (D{sub 2}O) vapor onto the rear surface of the target prior to the shot. Within the range of our detectors (0°–8.5°), we find laser-to-deuterium-ion energy conversion efficiency of 4.3% above 0.7 MeV/nucleon while a conservative estimate of the total beam gives a conversion efficiency of 9.4%.

Selective deuterium ion acceleration using the Vulcan petawatt laser

International Nuclear Information System (INIS)

Krygier, A. G.; Morrison, J. T.; Kar, S.; Ahmed, H.; Alejo, A.; Green, A.; Jung, D.; Clarke, R.; Notley, M.; Fuchs, J.; Vassura, L.; Kleinschmidt, A.; Roth, M.; Najmudin, Z.; Nakamura, H.; Norreys, P.; Oliver, M.; Zepf, M.; Borghesi, M.; Freeman, R. R.

2015-01-01

We report on the successful demonstration of selective acceleration of deuterium ions by target-normal sheath acceleration (TNSA) with a high-energy petawatt laser. TNSA typically produces a multi-species ion beam that originates from the intrinsic hydrocarbon and water vapor contaminants on the target surface. Using the method first developed by Morrison et al. [Phys. Plasmas 19, 030707 (2012)], an ion beam with >99% deuterium ions and peak energy 14 MeV/nucleon is produced with a 200 J, 700 fs, >10 20 W/cm 2 laser pulse by cryogenically freezing heavy water (D 2 O) vapor onto the rear surface of the target prior to the shot. Within the range of our detectors (0°–8.5°), we find laser-to-deuterium-ion energy conversion efficiency of 4.3% above 0.7 MeV/nucleon while a conservative estimate of the total beam gives a conversion efficiency of 9.4%

Selective deuterium ion acceleration using the Vulcan petawatt laser

Science.gov (United States)

Krygier, A. G.; Morrison, J. T.; Kar, S.; Ahmed, H.; Alejo, A.; Clarke, R.; Fuchs, J.; Green, A.; Jung, D.; Kleinschmidt, A.; Najmudin, Z.; Nakamura, H.; Norreys, P.; Notley, M.; Oliver, M.; Roth, M.; Vassura, L.; Zepf, M.; Borghesi, M.; Freeman, R. R.

2015-05-01

We report on the successful demonstration of selective acceleration of deuterium ions by target-normal sheath acceleration (TNSA) with a high-energy petawatt laser. TNSA typically produces a multi-species ion beam that originates from the intrinsic hydrocarbon and water vapor contaminants on the target surface. Using the method first developed by Morrison et al. [Phys. Plasmas 19, 030707 (2012)], an ion beam with >99% deuterium ions and peak energy 14 MeV/nucleon is produced with a 200 J, 700 fs, > 10 20 W / cm 2 laser pulse by cryogenically freezing heavy water (D2O) vapor onto the rear surface of the target prior to the shot. Within the range of our detectors (0°-8.5°), we find laser-to-deuterium-ion energy conversion efficiency of 4.3% above 0.7 MeV/nucleon while a conservative estimate of the total beam gives a conversion efficiency of 9.4%.

Exclusive ρ0 meson cross section ratios on deuterium and hydrogen targets

International Nuclear Information System (INIS)

Osborne, A.G.S.

2006-06-01

The HERMES experiment is a large forward angle spectrometer located at the HERA accelerator ring at DESY, Hamburg. This thesis presents the analysis of the kinematic dependencies of ρ 0 vector meson production on hydrogen and deuterium targets. The relative gluon and quark contribution to the ρ 0 production amplitude is expected to depend on the kinematical variable x Bj , and by measuring the ratio of ρ 0 electroproduction cross sections on deuterium and hydrogen from HERMES data this dependence is confirmed. This thesis describes the methods used to extract the cross section ratio from the HERMES data taken between the years 1996 and 2000 and compares the results with the theoretical predictions. Until 2005 the missing mass resolution of the HERMES spectrometer was only sufficient to allow exclusivity at the level of a data sample. The HERMES Recoil Detector, installed in early 2006, is an upgrade which will augment the HERMES spectrometer by establishing exclusivity at the event level and therefore improving the resolution to which various kinematical variables may be reconstructed. Additionally, the Recoil Detector will contribute to the overall background suppression capability of the HERMES spectrometer. These improvements will provide a strong reduction in the statistical uncertainties present in the ρ 0 -analysis and other analyses at HERMES. The Recoil Detector critically relies on its track reconstruction software to enable its capability to provide event level exclusive measurements. This tracking code is presented in detail. (orig.)

Deuterium isotope separation

International Nuclear Information System (INIS)

Benson, S.W.

1979-01-01

Deuterium-containing molecules are separated and enriched by exposing commercially available ethylene, vinyl chloride, 1,2-dichloroethane or propylene to the radiation of tuned infrared lasers to selectively decompose these compounds into enriched molecular products containing deuterium atoms. The deuterium containing molecules can be easily separated from the starting material by absorption, distillation or other simple chemical separation techniques and methods. After evaporation such deuterium containing molecules can be burned to form water with an enriched deuterium content or pyrolyzed to form hydrogen gas with an enriched deuterium content. (author)

Work of the Liquid Deuterium Target of the Joint Institute for Nuclear Research at the Yerevan Electron Acceleration Ring

CERN Document Server

Golovanov, L B; Panebratsev, Yu A; Tsvinev, A P; Chumakov, V F; Shimansky, S S; Babayan, K Z; Mirzoyan, A E; Movsesyan, G D; Sirunyan, A M

2003-01-01

A cryogenic installation with a target filled with liquid hydrogen (deuterium), developed in the LHE JINR is described. The installation was used in an experimental run at the Yerevan ring accelerator with a beam of polarized photons. A description of the installation, features of its work in the YerPhI and its operational parameters is given.

Kinetic simulation of neutron production in a deuterium z-pinch

International Nuclear Information System (INIS)

Mostrom, C.; Stygar, William A.; Thoma, Carsten; Welch, Dale Robert; Clark, R.E.; Leeper, Ramon Joe; Rose, David V.

2010-01-01

We have found computationally that, at sufficiently high currents, half of the neutrons produced by a deuterium z pinch are thermonuclear in origin. Early experiments below 1-MA current found that essentially all of the neutrons produced by a deuterium pinch are not thermonuclear, but are initiated by an instability that creates beam-target neutrons. Many subsequent authors have supported this result while others have claimed that pinch neutrons are thermonuclear. To resolve this issue, we have conducted fully kinetic, collisional, and electromagnetic simulations of the complete time evolution of a deuterium pinch. We find that at 1-MA pinch currents, most of the neutrons are, indeed, beam-target in origin. At much higher current, half of the neutrons are thermonuclear and half are beam-target driven by instabilities that produce a power law fall off in the ion energy distribution function at large energy. The implications for fusion energy production with such pinches are discussed.

Properties of thick GEM in low-pressure deuterium

International Nuclear Information System (INIS)

Lee, C S; Ota, S; Tokieda, H; Kojima, R; Watanabe, Y N; Uesaka, T

2014-01-01

Deuteron inelastic scattering (d, d') provides a promising spectroscopic tool to study nuclear incompressibility. In studies of deuteron inelastic scattering of unstable nuclei, measurements of low-energy recoiled particles is very important. In order to perform these measurements, we are developing a GEM-TPC based gaseous active target, called CAT (Center for nuclear study Active Target), operated with pure deuterium gas. The CAT has been tested with deuterium gas at 1 atm and 100-μm-thick GEMs. The low-pressure operation of CAT is planned in order to improve the detection capability for lower-energy recoil particles. A 400 μm-thick gas electron multiplier (THGEM) was chosen for the low-pressure operation of CAT. However, the properties of THGEM in low-pressure deuterium are currently undocumented. In this work, the performance of THGEM with low-pressure pure deuterium gas has been investigated. The effective gas gain of THGEM has been measured in various conditions using a 5.5-MeV 241 Am alpha source. The effective gas gain was measured for 0.2-, 0.3- and 0.4-atm deuterium gas and a gas gain of about 10 3 was achieved by a double THGEM structure at 0.2 atm. The maximum achieved gain decreased with increasing gas pressure. The dependences of the effective gas gain on the electric field strengths of the drift, transfer and induction regions were investigated. The gain stability as a function of time in hydrogen gas was also tested and a relaxation time of THGEM of about 60 hours was observed with a continuous irradiation of alpha particles, which is significantly longer than previous studies have reported. We have tried to evaluate the gas gain of THGEM in deuterium gas by considering only the Townsend ionization process; however, it turned out that more phenomenological aspects, such as transfer efficiency, should be included in the evaluation. The basic properties of THGEM in low-pressure deuterium have been investigated for the first time

Properties of thick GEM in low-pressure deuterium

Science.gov (United States)

Lee, C. S.; Ota, S.; Tokieda, H.; Kojima, R.; Watanabe, Y. N.; Uesaka, T.

2014-05-01

Deuteron inelastic scattering (d, d') provides a promising spectroscopic tool to study nuclear incompressibility. In studies of deuteron inelastic scattering of unstable nuclei, measurements of low-energy recoiled particles is very important. In order to perform these measurements, we are developing a GEM-TPC based gaseous active target, called CAT (Center for nuclear study Active Target), operated with pure deuterium gas. The CAT has been tested with deuterium gas at 1 atm and 100-μm-thick GEMs. The low-pressure operation of CAT is planned in order to improve the detection capability for lower-energy recoil particles. A 400 μm-thick gas electron multiplier (THGEM) was chosen for the low-pressure operation of CAT. However, the properties of THGEM in low-pressure deuterium are currently undocumented. In this work, the performance of THGEM with low-pressure pure deuterium gas has been investigated. The effective gas gain of THGEM has been measured in various conditions using a 5.5-MeV 241Am alpha source. The effective gas gain was measured for 0.2-, 0.3- and 0.4-atm deuterium gas and a gas gain of about 103 was achieved by a double THGEM structure at 0.2 atm. The maximum achieved gain decreased with increasing gas pressure. The dependences of the effective gas gain on the electric field strengths of the drift, transfer and induction regions were investigated. The gain stability as a function of time in hydrogen gas was also tested and a relaxation time of THGEM of about 60 hours was observed with a continuous irradiation of alpha particles, which is significantly longer than previous studies have reported. We have tried to evaluate the gas gain of THGEM in deuterium gas by considering only the Townsend ionization process; however, it turned out that more phenomenological aspects, such as transfer efficiency, should be included in the evaluation. The basic properties of THGEM in low-pressure deuterium have been investigated for the first time.

Exclusive {rho}{sup 0} meson cross section ratios on deuterium and hydrogen targets

Energy Technology Data Exchange (ETDEWEB)

Osborne, A.G.S.

2006-08-15

The HERMES experiment is a large forward angle spectrometer located at the HERA accelerator ring at DESY, Hamburg. This thesis presents the analysis of the kinematic dependencies of {rho}{sup 0} vector meson production on hydrogen and deuterium targets. The relative gluon and quark contribution to the {rho}{sup 0} production amplitude is expected to depend on the kinematical variable x{sub Bj}, and by measuring the ratio of {rho}{sup 0} electroproduction cross sections on deuterium and hydrogen from HERMES data this dependence is confirmed. This thesis describes the methods used to extract the cross section ratio from the HERMES data taken between the years 1996 and 2000 and compares the results with the theoretical predictions. Until 2005 the missing mass resolution of the HERMES spectrometer was only sufficient to allow exclusivity at the level of a data sample. The HERMES Recoil Detector, installed in early 2006, is an upgrade which will augment the HERMES spectrometer by establishing exclusivity at the event level and therefore improving the resolution to which various kinematical variables may be reconstructed. Additionally, the Recoil Detector will contribute to the overall background suppression capability of the HERMES spectrometer. These improvements will provide a strong reduction in the statistical uncertainties present in the {rho}{sup 0}-analysis and other analyses at HERMES. The Recoil Detector critically relies on its track reconstruction software to enable its capability to provide event level exclusive measurements. This tracking code is presented in detail. (orig.)

Deuterium and heavy water

International Nuclear Information System (INIS)

Vasaru, G.; Ursu, D.; Mihaila, A.; Szentgyorgyi, P.

1975-01-01

This bibliography on deuterium and heavy water contains 3763 references (1932-1974) from 43 sources of information. An author index and a subject index are given. The latter contains a list of 136 subjects, arranged in 13 main topics: abundance of deuterium , catalysts, catalytic exchange, chemical equilibria, chemical kinetics, deuterium and heavy water analysis, deuterium and heavy water properties, deuterium and heavy water separation, exchange reactions, general review, heavy water as moderator, isotope effects, synthesis of deuterium compounds

Deuterium pass through target

International Nuclear Information System (INIS)

Alger, D.L.

1975-01-01

A neutron emitting target is described for use in neutron generating apparatus including a deuteron source and an accelerator vacuum chamber. The target consists of a tritium-containing target layer, a deuteron accumulation layer, and a target support containing passages providing communication between the accumulation layer and portions of the surface of the support exposed to the accelerator vacuum chamber. With this arrangement, deuterons passing through the target layer and implanting in and diffusing through the accumulation layer, diffuse into the communicating passages and are returned to the accelerator vacuum chamber. The invention allows the continuous removal of deuterons from the target in conventional water cooled neutron generating apparatus. Preferably, the target is provided with thin barrier layers to prevent undesirable tritium diffusion out of the target layer, as well as deuteron diffusion into the target layer

Characterization of a deuterium-deuterium plasma fusion neutron generator

Science.gov (United States)

Lang, R. F.; Pienaar, J.; Hogenbirk, E.; Masson, D.; Nolte, R.; Zimbal, A.; Röttger, S.; Benabderrahmane, M. L.; Bruno, G.

2018-01-01

We characterize the neutron output of a deuterium-deuterium plasma fusion neutron generator, model 35-DD-W-S, manufactured by NSD/Gradel-Fusion. The measured energy spectrum is found to be dominated by neutron peaks at 2.2 MeV and 2.7 MeV. A detailed GEANT4 simulation accurately reproduces the measured energy spectrum and confirms our understanding of the fusion process in this generator. Additionally, a contribution of 14 . 1 MeV neutrons from deuterium-tritium fusion is found at a level of 3 . 5%, from tritium produced in previous deuterium-deuterium reactions. We have measured both the absolute neutron flux as well as its relative variation on the operational parameters of the generator. We find the flux to be proportional to voltage V 3 . 32 ± 0 . 14 and current I 0 . 97 ± 0 . 01. Further, we have measured the angular dependence of the neutron emission with respect to the polar angle. We conclude that it is well described by isotropic production of neutrons within the cathode field cage.

Deuterium-depleted water

International Nuclear Information System (INIS)

Stefanescu, Ion; Steflea, Dumitru; Saros-Rogobete, Irina; Titescu, Gheorghe; Tamaian, Radu

2001-01-01

Deuterium-depleted water represents water that has an isotopic content smaller than 145 ppm D/(D+H) which is the natural isotopic content of water. Deuterium depleted water is produced by vacuum distillation in columns equipped with structured packing made from phosphor bronze or stainless steel. Deuterium-depleted water, the production technique and structured packing are patents of National Institute of Research - Development for Cryogenics and Isotopic Technologies at Rm. Valcea. Researches made in the last few years showed the deuterium-depleted water is a biological active product that could have many applications in medicine and agriculture. (authors)

Development of a new deuterium-deuterium (D-D) neutron generator for prompt gamma-ray neutron activation analysis.

Science.gov (United States)

Bergaoui, K; Reguigui, N; Gary, C K; Brown, C; Cremer, J T; Vainionpaa, J H; Piestrup, M A

2014-12-01

A new deuterium-deuterium (D-D) neutron generator has been developed by Adelphi Technology for prompt gamma neutron activation analysis (PGNAA), neutron activation analysis (NAA), and fast neutron radiography. The generator makes an excellent fast, intermediate, and thermal neutron source for laboratories and industrial applications that require the safe production of neutrons, a small footprint, low cost, and small regulatory burden. The generator has three major components: a Radio Frequency Induction Ion Source, a Secondary Electron Shroud, and a Diode Accelerator Structure and Target. Monoenergetic neutrons (2.5MeV) are produced with a yield of 10(10)n/s using 25-50mA of deuterium ion beam current and 125kV of acceleration voltage. The present study characterizes the performance of the neutron generator with respect to neutron yield, neutron production efficiency, and the ionic current as a function of the acceleration voltage at various RF powers. In addition the Monte Carlo N-Particle Transport (MCNP) simulation code was used to optimize the setup with respect to thermal flux and radiation protection. Copyright © 2014 Elsevier Ltd. All rights reserved.

Wildcat: A commercial deuterium-deuterium tokamak reactor

International Nuclear Information System (INIS)

Evans, K.; Baker, C.C.; Barry, K.M.

1983-01-01

WILDCAT is a conceptual design of a catalyzed deuterium-deuterium tokamak commercial fusion reactor. WILDCAT utilizes the beneficial features of no tritium breeding, while not extrapolating unnecessarily from existing deuterium-tritium (D-T) designs. The reactor is larger and has higher magnetic fields and plasma pressures than typical D-T devices. It is more costly, but eliminates problems associated with tritium breeding and has tritium inventories and throughputs approximately two orders of magnitude less than typical D-T reactors. There are both a steady-state version with Alfven-wave current drive and a pulsed version. Extensive comparison with D-T devices has been made, and cost and safety analyses have been included. All of the major reactor systems have been worked out to a level of detail appropriate to a complete conceptual design

Effect of deposited tungsten on deuterium accumulation in beryllium in contact with atomic deuterium

Energy Technology Data Exchange (ETDEWEB)

Sharapov, V.M.; Gavrilov, L.E. [Institute of Physical Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Kulikauskas, V.S.

1998-01-01

Usually ion or plasma beam is used for the experiment with beryllium which simulates the interaction of plasma with first wall in fusion devices. However, the use of thermal or subthermal atoms of hydrogen isotopes seems to be useful for that purpose. Recently, the authors have studied the deuterium accumulation in beryllium in contact with atomic deuterium. The experimental setup is shown, and is explained. By means of elastic recoil detection (ERD) technique, it was shown that in the exposure to D atoms at 740 K, deuterium is distributed deeply into the bulk, and is accumulated up to higher concentration than the case of the exposure to molecular deuterium. The depth and concentration of deuterium distribution depend on the exposure time, and those data are shown. During the exposure to atomic deuterium, oxide film grew on the side of a sample facing plasma. In order to understand the mechanism of deuterium trapping, the experiment was performed using secondary ion mass spectrometry (SIMS) and residual gas analysis (RGA). The influence that the tungsten deposit from the heated cathode exerted to the deuterium accumulation in beryllium in contact with atomic deuterium was investigated. These results are reported. (K.I.)

Evidence for neutron production in deuterium gas with a pyroelectric crystal without tip

International Nuclear Information System (INIS)

Tornow, W.; Shafroth, S. M.; Brownridge, J. D.

2008-01-01

We present evidence for the production of 2 H(d,n) 3 He neutrons in gaseous deuterium by using a pyroelectric crystal as positive ion accelerator. In contrast to previous studies, neutrons were generated without a tip attached to the crystal and without using a solid deuterated target. The deuterium gas provided both the projectile and target nuclei. On the average, 1 neutron/s was obtained in our ''hot fusion'' experimental setup. No neutrons were detected when a tip was used

Effect of Coulomb screening on deuterium-deuterium fusion cross-section

International Nuclear Information System (INIS)

Wang Shunjin

1991-01-01

The popular Gamow formula for the deuterium-deuterium fusion cross-section is generalized to take into account the Coulomb screening effect. The generalized formula has been used to discuss the fusion process occurring in the metal medium

Deuterium exchange between hydrofluorocarbons and amines

International Nuclear Information System (INIS)

Hammond, W.B.; Bigeleisen, J.; Tuccio, S.A.

1983-01-01

The invention consists of a process for obtaining a compound enriched in deuterium which comprises the known method of exposing a gaseous hydrofluorocarbon to infrared laser radiation of a predetermined frequency to selectively cause a chemical reaction involving hydrofluorocarbon molecules containing deuterium without substantially affecting hydrofluorocarbon molecules not containing deuterium, thereby producing, as reaction products, a compound enriched in deuterium and hydrofluorocarbon depleted in deuterium; combined with a new method, which comprises enriching the deuterium content of the depleted hydrofluorocarbon by contacting the depleted hydrofluorocarbon with an alkali metal amide and an amine having a concentration of deuterium at least that which will yield an increase in deuterium concentration of the hydrofluorocarbon upon equilibration, whereby the amine becomes depleted in deuterium

Producing deuterium-enriched products

International Nuclear Information System (INIS)

1980-01-01

A method of producing an enriched deuterium product from a gaseous feed stream of mixed hydrogen and deuterium, comprises: (a) combining the feed stream with gaseous bromine to form a mixture of the feed stream and bromine and exposing the mixture to an electrical discharge effective to form deuterium bromide and hydrogen bromide with a ratio of D/H greater than the ratio of D/H in the feed stream; and (b) separating at least a portion of the hydrogen bromide and deuterium bromide from the mixture. (author)

Neutron production with mixture of deuterium and krypton in Sahand Filippov type plasma focus facility

International Nuclear Information System (INIS)

Mohammadi, M.A.; Sobhanian, S.; Rawat, R.S.

2011-01-01

This Letter reports the order of magnitude enhancement in neutron yield from Sahand plasma focus device with krypton seeded deuterium operation. The highest average neutron yield of 2.2x10 9 neutrons per shot was achieved at 1.00 Torr deuterium with 3% krypton which is higher than the best average neutron yield of 3.18x10 8 neutrons per shot for pure deuterium operation. Estimation of average neutron energy showed that the maximum and minimum average energies are 2.98±0.6 MeV at 16 kV in 0.25 Torr deuterium with 3% Kr and 2.07±0.2 MeV at 18 kV operation in 0.5 Torr deuterium with 3% Kr, respectively. The anisotropy of neutron emission from Sahand DPF showed that the neutrons are produced mainly by beam-target mechanisms. -- Highlights: → The highest average neutron yield of 2.2x10 9 neutrons per shot was achieved at mixture of deuterium and krypton. → In the krypton seeding of deuterium also anisotropy of neutron emission deuterium is found. → The krypton seeding of deuterium made the neutron emission more reliable over wider operating pressure ranges.

Deuterium depth profiling in JT-60U W-shaped divertor tiles by nuclear reaction analysis

International Nuclear Information System (INIS)

Hayashi, T.; Ochiai, K.; Masaki, K.; Gotoh, Y.; Kutsukake, C.; Arai, T.; Nishitani, T.; Miya, N.

2006-01-01

Deuterium concentrations and depth profiles in plasma-facing graphite tiles used in the divertor of JAERI Tokamak-60 Upgrade (JT-60U) were investigated by nuclear reaction analysis (NRA). The highest deuterium concentration of D/ 12 C of 0.053 was found in the outer dome wing tile, where the deuterium accumulated probably through the deuterium-carbon co-deposition. In the outer and inner divertor target tiles, the D/ 12 C data were lower than 0.006. Additionally, the maximum (H + D)/ 12 C in the dome top tile was estimated to be 0.023 from the results of NRA and secondary ion mass spectroscopy (SIMS). Orbit following Monte-Carlo (OFMC) simulation showed energetic deuterons caused by neutral beam injections (NBI) were implanted into the dome region with high heat flux. Furthermore, the surface temperature and conditions such as deposition and erosion significantly influenced the accumulation process of deuterium. The deuterium depth profile, scanning electron microscope (SEM) observation and OFMC simulation indicated the deuterium was considered to accumulate through three processes: the deuterium-carbon co-deposition, the implantation of energetic deuterons and the deuterium diffusion into the bulk

Deuterium migration and trapping in uranium and uranium dioxide during D+ implantation

International Nuclear Information System (INIS)

Lewis, M.B.

1980-01-01

Uranium and UO 2 have been implanted with deuterium ions in the energy range 30-85 keV. Subsequently, the near surface regions (100-90000 Angstroem) of these samples were quantitatively profiled for deuterium oxygen using the method of ion beam microanalysis. Mean ranges and widths of the implanted ions were measured and compared with theoretical predictions. Fully oxidized samples were compared with those having only thin oxide films on their surfaces. While the deuterium appeared to migrate during its implantation in uranium, little or no migration appeared either during or after implantation in UO 2 . Further measurements suggest that thin surface oxide films strongly trap the deuterium migrating beneath the surface. It is suggested that the electronic energy loss of the ion beam lowers the effective activation energy for the formation of OD bonds near the target surface. (orig.)

Deuterium - depleted water. Achievements and perspectives

International Nuclear Information System (INIS)

Titescu, Gh.; Stefanescu, I.; Saros-Rogobete, I.

2001-01-01

Deuterium - depleted water represents water that has an isotopic content lower than 145 ppm D/(D+H) which is the natural isotopic content of water. The research conducted at ICSI Ramnicu Valcea, regarding deuterium - depleted water were completed by the following patents: - technique and installation for deuterium - depleted water production; - distilled water with low deuterium content; - technique and installation for the production of distilled water with low deuterium content; - mineralized water with low deuterium content and technique to produce it. The gold and silver medals won at international salons for inventions confirmed the novelty of these inventions. Knowing that deuterium content of water has a big influence on living organisms, beginning with 1996, the ICSI Ramnicu Valcea, deuterium - depleted water producer, co-operated with Romanian specialized institutes for biological effects' evaluation of deuterium - depleted water. The role of natural deuterium in living organisms was examined by using deuterium - depleted water instead of natural water. These investigations led to the following conclusions: 1. deuterium - depleted water caused a tendency towards the increase of the basal tone, accompanied by the intensification of the vasoconstrictor effects of phenylefrine, noradrenaline and angiotensin; the increase of the basal tone and vascular reactivity produced by the deuterium - depleted water persists after the removal of the vascular endothelium; -2. animals treated with deuterium - depleted water showed an increase of the resistance both to sublethal and to lethal gamma radiation doses, suggesting a radioprotective action by the stimulation of non-specific immune defence mechanism; 3, deuterium - depleted water stimulates immune defence reactions, represented by the opsonic, bactericidal and phagocyte capacity of the immune system, together with increase in the numbers of polymorphonuclear neutrophils; 4. investigations regarding artificial

Radiation damage and deuterium trapping in deuterium-ion-irradiated Fe–9Cr alloy

Energy Technology Data Exchange (ETDEWEB)

Iwakir, Hirotomo, E-mail: iwakiri@edu.u-ryukyu.ac.jp [Faculty and Graduate School of Education, University of the Ryukyus, Nishihara, Okinawa 903-0213 (Japan); Tani, Munechika [Interdisciplinary Graduate School of Engineering Sciences, Kyusyu University, Kasuga, Fukuoka 816-8580 (Japan); Watanabe, Yoshiyuki [Japan Atomic Energy Agency, Rokkasho, Aomori 039-3212 (Japan); Yoshida, Naoaki [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan)

2014-01-15

Thermal desorption of deuterium (D{sub 2}) from deuterium-ion (D{sub 2}{sup +})-irradiated Fe–9Cr was correlated with the microstructural evolution of the alloy during irradiation with 8-keV D{sub 2}{sup +} ions following annealing to determine the retention and desorption behavior of the implanted deuterium and to identify effective traps for them, particularly at high temperature. After irradiation at 573 K, a new desorption stage formed between 650 and 1100 K at higher fluences, and cavities were observed using transmission electron microscopy. The total amount of trapped deuterium following irradiation with a fluence of 3.0 × 10{sup 22} ions/m{sup 2} was 6.8 × 10{sup 17} D{sub 2}/m{sup 2}, or approximately 0.007%. These results indicate that the deuterium atoms recombined to form D{sub 2} molecules at the surfaces of the cavities.

Neutron scattering with deuterium labeling reveals the nature of complexes formed by Ca{sup 2+}-binding proteins and their regulatory targets

Energy Technology Data Exchange (ETDEWEB)

Trewhella, J. [Los Alamos National Laboratory, NM (United States)

1994-12-01

Small-angle neutron scattering with deuterium labeling is extremely useful for studying the structures of complex biomolecular assemblies in solution. The different neutron scattering properties of their isotopes of hydrogen combines with the ability to uniformly label biomolecules with deuterium allow one to characterize the structures and relative dispositions of the individual components of an assembly using methods of {open_quotes}contrast variation.{close_quotes} We have applied these techniques to studies of the evolutionarily related dumbbell-shaped Ca{sup 2+}-binding proteins calmodulin and troponin C and their interactions with the target proteins whose activities they regulate. Ca{sup 2+} is one of the simplest of nature`s messengers used in the communication pathways between physiological stimulus and cellular response. The signaling mechanism generally involves Ca{sup 2+} binding to a protein and inducing a conformational change that transmits a signal to modify the activity of a specific target protein. Ca{sup 2+} is thus important in the regulation of a diverse array of intracellular responses, including neurotransmitter release, muscle contraction, the degradation of glycogen to glucose to generate energy, microtubule assembly, membrane phosphorylation, etc. It is the conformational language of the Ca{sup 2+} induced signal transduction that we have sought to understand because of its central importance to biochemical regulation and, hence, to healthy cellular function.

Apparatus for producing laser targets

International Nuclear Information System (INIS)

Jarboe, T.R.; Baker, W.R.

1975-01-01

This patent relates to an apparatus and method for producing deuterium targets or pellets of 25u to 75u diameter. The pellets are sliced from a continuously spun solid deuterium thread at a rate of up to 10 pellets/second. The pellets after being sliced from the continuous thread of deuterium are collimated and directed to a point of use, such as a laser activated combustion or explosion chamber wherein the pellets are imploded by laser energy or laser produced target plasmas for neutral beam injection

Development of a hydrogen and deuterium polarized gas target for application in storage rings. Annual report, February 1, 1986-January 31, 1987

International Nuclear Information System (INIS)

Haeberli, W.

1986-01-01

Insertion of an internal polarized gas target into storage rings for protons, antiprotons or electrons would permit interesting new experiments, particularly if the circulating beam is polarized as well. The purpose of the present project is the development of a polarized gas target, based on injection of polarized hydrogen or deuterium atoms into a storage cell in order to build up the required target thickness. A method has been developed and tested, which permits measurement of the target polarization under realistic conditions (i.e., in the presence of an intense ion beam) without the need for a large accelerator. First measurements with an oxidized aluminum cell have been made. It is proposed to study wall depolarization in storage cells and to search for suitable wall conditions (wall material, coating, temperature, vacuum conditions) to permit eventual construction of a polarized gas target for a storage ring

Method of deuterium isotope separation and enrichment

International Nuclear Information System (INIS)

Benson, S.W.

1978-01-01

A method of separating deuterium, i.e., heavy hydrogen, from certain naturally occurring sources using tuned infrared lasers to selectively decompose specified classes of organic molecules (i.e., RX) into enriched molecular products containing deuterium atoms is described. The deuterium containing molecules are easily separated from the starting material by absorption, distillation or other simple chemical separation techniques and methods. After evaporation such deuterium containing molecules can be burned to form water with an enriched deuterium content or pyrolyzed to form hydrogen gas with an enriched deuterium content. The undecomposed molecules and the other reaction products which are depleted of their deuterium containing species can be catalytically treated, preferably using normal water, to restore the natural abundance of deuterium and such restored molecules can then be recycled

Photoproduction of neutral kaons on a liquid deuterium target in the threshold region

Czech Academy of Sciences Publication Activity Database

Tsukada, K.; Takahashi, T.; Watanabe, T.; Fujii, Y.; Futatsukawa ., K.; Hashimoto, O.; Hirose, K.; Ito, K.; Kameoka, S.; Kanda, H.; Maeda, K.; Matsumura, A.; Miura, Y.; Myiase, H.; Nakamura, S. N.; Nomura, H.; Nonaka, K.; Osaka, T.; Okayasu, Y.; Tamura, H.; Tsubota, H.; Ukai, M.; Yamauchi, H.; Wakamatsu, M.; Ishikawa, T.; Kinoshita, T.; Miyahara, F.; Nakabayashi, T.; Shimizu, H.; Tamae, T.; Yamazaki, H.; Sasaki, A.; Konno, O.; Bydžovský, Petr; Sotona, Miloslav

2008-01-01

Roč. 78, - (2008), 014001/1-014000/10 ISSN 0556-2813 R&D Projects: GA ČR GA202/05/2142 Institutional research plan: CEZ:AV0Z10480505 Keywords : neutral kaons * liguit deuterium * treshold region Subject RIV: BE - Theoretical Physics Impact factor: 3.124, year: 2008

H-mode WEST tungsten divertor operation: deuterium and nitrogen seeded simulations with SOLEDGE2D-EIRENE

Directory of Open Access Journals (Sweden)

G. Ciraolo

2017-08-01

Full Text Available Simulations of WEST H-mode divertor scenarios have been performed with SOLEDGE2D-EIRENE edge plasma transport code, both for pure deuterium and nitrogen seeded discharge. In the pure deuterium case, a target heat flux of 8 MW/m2 is reached, but misalignment between heat and the particle outflux yields 50 eV plasma temperature at the target plates. With nitrogen seeding, the heat and particle outflux are observed to be aligned so that lower plasma temperatures at the target plates are achieved together with the required high heat fluxes. This change in heat and particle outflux alignment is analysed with respect to the role of divertor geometry and the impact of vertical vs horizontal target plates on neutrals spreading.

Deuterium abundance, from ultraviolet to visible

International Nuclear Information System (INIS)

Hebrard, Guillaume

2000-01-01

In the frame of the standard Big Bang model, the primordial abundance of deuterium is the most sensitive to the baryonic density of the Universe. It was synthesized only during the primordial nucleosynthesis few minutes after the Big Bang and no other standard mechanism is able to produce any further significant amount. On the contrary, since deuterium is burned up within stars, its abundance D/H decreases along cosmic evolution. Thus, D/H measurements constrain Big Bang and galactic chemical evolution models. There are three samples of deuterium abundances: primordial, proto-solar and interstellar. Each of them is representative of a given epoch, respectively about 15 Gyrs past, 4.5 Gyrs past and present epoch. Although the evolution of the deuterium abundance seems to be qualitatively understood, the measurements show some dispersion. Present thesis works are linked to deuterium interstellar abundance measurements. Such measurements are classically obtained from spectroscopic observations of the hydrogen and deuterium Lyman series in absorption in the ultraviolet spectral range, using space observatories. Results presented here were obtained with the Hubble Space Telescope and FUSE, which has recently been launched. Simultaneously, a new way to observe deuterium has been proposed, in the visible spectral range from ground-based telescopes. This has led to the first detections and the identification of the deuterium Balmer series, in emission in HII regions, using CFHT and VLT telescopes. (author) [fr

Deuterium-depleted water. Romanian achievements and perspective

International Nuclear Information System (INIS)

Stefanescu, Ion; Saros-Rogobete, Irina; Titescu, Gheorghe

2001-01-01

Deuterium-depleted water has an isotopic content smaller than 145 ppm D/(D+H) which is the natural isotopic content of water. Beginning with 1996 ICSI Rm. Valcea, deuterium-depleted water producer, co-operated with Romanian specialized institutes for biological effect's evaluation of deuterium-depleted water. These investigations lead to the following conclusions: - Deuterium-depleted water caused a tendency towards the increase of the basal tonus, accompanied by the intensification of the vasoconstrictor effects of phenylefrine, noradrenaline and angiotensin; the increase of the basal tonus and vascular reactivity produced by the deuterium-depleted water persist after the removal of the vascular endothelium; - Animals treated with deuterium-depleted water showed an increase of the resistance both to sublethal and to lethal gamma radiation doses, suggesting a radioprotective action; - Deuterium-depleted water stimulates immune defence reactions and increases the numbers of polymorphonuclear neutrophils; - Investigations regarding artificial reproduction of fish with deuterium-depleted water fecundated solutions confirmed favourable influence in embryo growth stage and resistance in subsequent growth stages; - It was studied germination, growth and quantitative character's variability in plants; one can remark the favourable influence of deuterium-depleted water on biological process in plants in various ontogenetic stages; - The deuterium depletion in seawater produces the diminution of the water spectral energy related to an increased metabolism of Tetraselmis Suecica. (authors)

Defect trapping of deuterium implanted in aluminium

International Nuclear Information System (INIS)

Kido, Y.; Kakeno, M.; Yamada, K.; Hioki, T.; Kawamoto, J.

1982-01-01

The behaviour of deuterium implanted in Al was studied by the D( 3 He,p) 4 He and the D(d,p)T nuclear reactions. Changes of the depth profiles of the deuterium after heat treatments indicated that the implanted deuterium was trapped by the defect produced during the deuterium implantation and the release probability of the trapped deuterium increased as the specimen temperature was raised. Assuming a thermal equilibrium locally in the region of high defect concentration, the trapping energy of deuterium in Al was determined to be 0.12eV. Since the release probability for the single crystal was considerably larger than that for the polycrystal specimens, the deuterium was considered to be strongly trapped in the grain boundaries. Distributions of displaced Al atoms and the recovery of the lattice damage by annealing were measured by the channelling technique. (author)

Codeposition of deuterium ions with beryllium oxide at elevated temperatures

CERN Document Server

Markin, A V; Gorodetsky, A E; Negodaev, M A; Rozhanskii, N V; Scaffidi-Argentina, F; Werle, H; Wu, C H; Zalavutdinov, R K; Zakharov, A P

2000-01-01

Deuterium-loaded BeO films were produced by sputtering the beryllium target with 10 keV Ne ions in D sub 2 gas at a pressure of approximately 1 Pa. The sputtered beryllium reacts - on the substrate surface - with the residual oxygen, thus forming a beryllium oxide layer. Biasing the substrate negatively with respect to the target provides the simultaneous bombardment of the growing film surface with D ions formed by Ne-D sub 2 collisions. Substrate potential governs the maximum energy of ions striking the growing film surface while its size governs the flux density. According to X-ray photoelectron spectroscopy (XPS), electron probe microanalysis (EPMA) and reflection high energy electron diffraction (RHEED) data, the beryllium is deposited in the form of polycrystalline hcp-BeO layers with negligible (about 1 at.%) carbon and neon retention. Thermal desorption spectroscopy (TDS) data shows a strong deuterium bonding, with a desorption peak at 950 K, in the films deposited at -50 and -400 V substrate potentia...

Investigation of processes due to deuterium pellets impinging on a rigid wall

International Nuclear Information System (INIS)

Thoener, M.

1982-04-01

Pellets accelerated with a centrifuge - for refuelling thermonuclear plasmas - ought not to be noticeably deformed, let alone destroyed. This happens if the relative velocity between the pellet and the rotor catching it is too high. This report describes an apparatus for determining the variation in shape of deuterium pellets as a function of the relative velocity. In this method the pellet, produced by extrusion, is electromagnetically accelerated by means of metal carriers from which they are separated and shot at a stationary, rigid wall. The impact of the pellet on the target is recorded in seven pictures by spark cinematography and the impact velocity is measured with light barriers. The critical impact velocity for cylindrical deuterium pellets is found to be 48 m/s. Up to this relative velocity deuterium pellets retain their shape, irrespective of the direction of incidence. (orig.)

Deuterium trapping in liquid lithium irradiated by deuterium plasma

International Nuclear Information System (INIS)

Pisarev, A.; Moshkunov, K.; Vizgalov, I.; Gasparyan, Yu.

2013-01-01

Liquid lithium was irradiated by deuterium plasma to a low fluence of 10 22 –10 23 D/m 2 , cooled down to room temperature, and then slowly heated. The temperature and release rate were measured during heating. Two plateaus on the temperature–time dependence were observed at 180 °C and 660 °C. The first one corresponds to melting of Li and the second one – either to melting or to decomposition of solid LiD. Features of deuterium release in TDS were interpreted in terms of decomposition of lithium deuterides formed during plasma irradiation

Deuterium ion irradiation damage and deuterium trapping mechanism in candidate stainless steel material (JPCA2) for fusion reactor

International Nuclear Information System (INIS)

Ashizuka, Norihiro; Kurita, Takaaki; Yoshida, Naoaki; Fujiwara, Tadashi; Muroga, Takeo

1987-01-01

An improved austenitic stainless steel (JPCA), a candidate material for fusion reactor, is irradiated at room temperature with deuterium ion beams. Desorption spectra of deuterium gas is measured at various increased temperatures and defects formed under irradiation are observed by transmission electron microscopy to determine the mechanism of the thermal release of deuteriums and the characteristics of irradiation-induced defects involved in the process. In the deuterium deportion spectra observed, five release stages are found to exist at 90 deg C, 160 deg C, 220 deg C, 300 deg C and 400 deg C, referred to as Stage I, II, III, IV and V, respectively. Stage I is interpreted as representing the release of deuteriums trapped in point defects (presumably vacancies) formed under irradiation. The energy of desorption from the trapping sites is estimated at 0.8 eV. Stage II is concluded to be associated with the release of deuteriums trapped in a certain kind of existing defects. Stage III involves the release of deuteriums that are trapped in dislocations, dislocation loops or dislocated portions of stacking fault tetrahedra. This release occurs significantly in processed materials and other materials irradiated with high energy ion beams that may cause cascade damage. Stage IV is interpreted in terms of thermal decomposition of small deuterium clusters. Stage V is associated with the decomposition of rather large deuterium clusters grown on the {111} plane. (Nogami, K.)

Method of producing deuterium-oxide-enriched water

International Nuclear Information System (INIS)

Mandel, H.

1976-01-01

A method and apparatus for producing deuterium-oxide-enriched water (e.g., as a source of deuterium-rich gas mixtures) are disclosed wherein the multiplicity of individual cooling cycles of a power plant are connected in replenishment cascade so that fresh feed water with a naturally occurring level of deuterium oxide is supplied to replace the vaporization losses, sludge losses and withdrawn portion of water in a first cooling cycle, the withdrawn water being fed as the feed water to the subsequent cooling cycle or stage and serving as the sole feed-water input to the latter. At the end of the replenishment-cascade system, the withdrawn water has a high concentration of deuterium oxide and may serve as a source of water for the production of heavy water or deuterium-enriched gas by conventional methods of removing deuterium oxide or deuterium from the deuterium-oxide-enriched water. Each cooling cycle may form part of a thermal or nuclear power plant in which a turbine is driven by part of the energy and air-cooling of the water takes place in the atmosphere, e.g., in a cooling tower

Method of deuterium isotope separation and enrichment

International Nuclear Information System (INIS)

Benson, S.W.

1979-01-01

A method is described for separating and enriching deuterium containing molecules comprising the steps of: providing a source of organic molecules containing a normal abundance of deuterium atoms, the organic molecules having a structural formula RX, in which R is an organic radical selected from ethyl, isopropyl, t-butyl and 3-cyclopentenyl, and in which X is selected from F, Cl, Br and OH, and wherein R represents 3-cyclopentenyl, X may additionally represent H; exposing the molecules to the radiation of at least one pulsed infrared laser source which has been specifically tuned and focussed to selectively decompose RX molecules containing deuterium to form an enriched olefin specie containing deuterium, and HX; and separating the deuterium enriched olefin specie from the undecomposed deuterium depleted RX molecules and HX. (author)

Thermal x-rays and deuterium production in stellar flares

International Nuclear Information System (INIS)

Colgate, S.A.

1977-01-01

The x-ray spectrum of flares is shown to be necessarily thermal up to greater than or equal to 200 keV because the self magnetic field of any electron stream required for a thick or thin target source is inconsistently large. The resulting flare model can then be related to stellar luminosity, convection and magnetic fields to result in a maximum possible γ-burst (Mullan, 1976) and continuous x-ray flux. One of the most striking isotopic anomalies observed is the extreme enrichment of Helium (3) in some solar flares and the mysterious depletion of deuterium. It is discussed how deuterium may be produced and emitted in the largest flares associated with γ-bursts but in amounts insufficient to support the tentative conclusion of Colemen and Worden

Catalyzed deuterium-deuterium and deuterium-tritium fusion blankets for high temperature process heat production

International Nuclear Information System (INIS)

Ragheb, M.M.H.; Salimi, B.

1982-01-01

Tritiumless blanket designs, associated with a catalyzed deuterium-deuterium (D-D) fusion cycle and using a single high temperature solid pebble or falling bed zone, for process heat production, are proposed. Neutronics and photonics calculations, using the Monte Carlo method, show that an about 90% heat deposition fraction is possible in the high temperature zone, compared to a 30 to 40% fraction if a deuterium-tritium (D-T) fusion cycle is used with separate breeding and heat deposition zones. Such a design is intended primarily for synthetic fuels manufacture through hydrogen production using high temperature water electrolysis. A system analysis involving plant energy balances and accounting for the different fusion energy partitions into neutrons and charged particles showed that plasma amplification factors in the range of 2 are needed. In terms of maximization of process heat and electricity production, and the maximization of the ratio of high temperature process heat to electricity, the catalyzed D-D system outperforms the D-T one by about 20%. The concept is thought competitive to the lithium boiler concept for such applications, with the added potential advantages of lower tritium inventories in the plasma, reduced lithium pumping (in the case of magnetic confinement) and safety problems, less radiation damage at the first wall, and minimized risks of radioactive product contamination by tritium

Deuterium/hydrogen isotope exchange on beryllium and beryllium nitride; Deuterium/Wasserstoff-Isotopenaustausch an Beryllium und Berylliumnitrid

Energy Technology Data Exchange (ETDEWEB)

Dollase, Petra; Eichler, Michael; Koeppen, Martin; Dittmar, Timo; Linsmeier, Christian [Forschungszentrum Juelich GmbH, Institut fuer Energie- und Klimaforschung - Plasmaphysik (Germany)

2016-07-01

In the fusion experiments JET and ITER, the first wall is made up of beryllium. The use of nitrogen is discussed for radiative cooling in the divertor. This can react with the surface of the first wall to form beryllium nitride (Be{sub 3}N{sub 2}). The hydrogen isotopes deuterium and tritium, which react in the fusion reaction to helium and a neutron, are used as fuel. Since the magnetic confinement of the plasma is not perfect, deuterium and tritium ions are also found on the beryllium wall and can accumulate there. This should be avoided due to the radioactivity of tritium. Therefore the isotope exchange with deuterium is investigated to regenerate the first wall. We investigate the isotopic exchange of deuterium and protium in order to have not to work with radioactive tritium. The ion bombardment is simulated with an ion source. With voltages up to a maximum of 5 kV, deuterium and protic hydrogen ions are implanted in polycrystalline Be and Be{sub 3}N{sub 2}. The samples are then analyzed in situ using X-ray photoelectron spectroscopy (XPS) and thermal desorption spectroscopy (TDS). Subsequently, samples prepared under the same conditions are characterized ex-situ by means of nuclear reaction analysis (NRA). [German] In den Fusionsexperimenten JET und ITER besteht die erste Wand im Hauptraum aus Beryllium (Be). Zur Strahlungskuehlung im Divertor wird der Einsatz von Stickstoff diskutiert. Dieser kann mit der Oberflaeche der ersten Wand zu Berylliumnitrid (Be{sub 3}N{sub 2}) reagieren. Als Brennstoff werden die Wasserstoffisotope Deuterium und Tritium eingesetzt, die in der Fusionsreaktion zu Helium und einem Neutron reagieren. Da der magnetische Einschluss des Plasmas nicht perfekt ist, treffen auch Deuterium- und Tritiumionen auf die Berylliumwand auf und koennen sich dort anreichern. Das soll aufgrund der Radioaktivitaet von Tritium unbedingt vermieden werden. Daher wird zur Regenerierung der ersten Wand der Isotopenaustausch mit Deuterium untersucht. Wir

Synthesis of deuterium-labeled fluphenazine.

Science.gov (United States)

Shetty, H U; Hawes, E M; Midha, K K

1984-01-01

The propylpiperazine side chain of fluphenazine has been labeled with two, four, and six deuterium atoms by lithium aluminum deuteride reduction of the appropriate ester or imide. The gamma-carbon of the propyl group was labeled with two deuterium atoms by reduction of 10- (2-methoxycarbonylethyl) -2-trifluoromethyl-10H-phenothiazine, while four deuterium atoms were incorporated into the piperazine ring by reduction of 10-[3-(3,5-dioxo-1-piperazinyl)propyl]-2-trifluoromethyl-10H-pheno thiazine. The latter reduction gave the d4-labeled N-deshydroxyethyl metabolite of fluphenazine.

Method of deuterium isotope separation and enrichment

International Nuclear Information System (INIS)

Benson, S.W.

1980-01-01

A method of deuterium isotope separation and enrichment using infrared laser technology in combination with chemical processes for treating and recycling the unreacted and deuterium-depleted starting materials is described. Organic molecules of the formula RX (where R is an ethyl, isopropyl, t-butyl, or cyclopentenyl group and X is F, Cl, Br or OH) containing a normal abundance of hydrogen and deuterium are exposed to intense laser infrared radiation. An olefin containing deuterium (olefin D) will be formed, along with HX. The enriched olefin D can be stripped from the depleted stream of RX and HX, and can be burned to form enriched water or pyrolyzed to produce hydrogen gas with elevated deuterium content. The depleted RX is decomposed to olefins and RX, catalytically exchanged with normal water to restore the deuterium content to natural levels, and recombined to form RX which can be recycled. (LL)

Point design for deuterium-deuterium compact reversed-field pinch reactors

International Nuclear Information System (INIS)

Dabiri, A.E.; Dobrott, D.R.; Gurol, H.; Schnack, D.D.

1984-01-01

A deuterium-deuterium (D-D) reversed-field pinch (RFP) reactor may be made comparable in size and cost to a deuterium-tritium (D-T) reactor at the expense of high-thermal heat load to the first wall. This heat load is the result of the larger percentage of fusion power in charged particles in the D-D reaction as compared to the D-T reaction. The heat load may be reduced by increasing the reactor size and hence the cost. In addition to this ''degraded'' design, the size may be kept small by means of a higher heat load wall, or by means of a toroidal divertor, in which case most of the heat load seen by the wall is in the form of radiation. Point designs are developed for these approaches and cost studies are performed and compared with a D-T reactor. The results indicate that the cost of electricity of a D-D RFP reactor is about20% higher than a D-T RFP reactor. This increased cost could be offset by the inherent safety features of the D-D fuel cycle

Distribution of deuterium and hydrogen in Zr and Ti foil assemblies under the action of a pulsed deuterium high-temperature plasma

Science.gov (United States)

Bondarenko, G. G.; Volobuev, I. V.; Eriskin, A. A.; Kobzev, A. P.; Nikulin, V. Ya.; Peregudova, E. N.; Silin, P. V.; Borovitskaya, I. V.

2017-09-01

Deuteron and proton elastic recoil detection analysis is used to study the accumulation and redistribution of deuterium and hydrogen in assemblies of two high-pure zirconium or titanium foils upon pulsed action of high-temperature deuterium plasma (PHTDP) in a plasma-focus installation PF-4. It is noted that, under the action of PHTDP, an implanted deuterium and hydrogen gas impurity are redistributed in the irradiated foils in large depths, which are significantly larger than the deuterium ion free paths (at their maximum velocity to 108 cm/s). The observed phenomenon is attributed to the carrying out of implanted deuterium and hydrogen under the action of powerful shock waves formed in the metallic foils under the action of PHTDP and/or the acceleration of diffusion of deuterium and hydrogen atoms under the action of a compression-rarefaction shock wave at the shock wave front with the redistribution of deuterium and hydrogen to large depths.

Erosion and deuterium retention of CLF-1 steel exposed to deuterium plasma

Science.gov (United States)

Qiao, L.; Wang, P.; Hu, M.; Gao, L.; Jacob, W.; Fu, E. G.; Luo, G. N.

2017-12-01

In recent years reduced activation ferritic martensitic steel has been proposed as the plasma-facing material in remote regions of the first wall. This study reports the erosion and deuterium retention behaviours in CLF-1 steel exposed to deuterium (D) plasma in a linear experimental plasma system as function of incident ion energy and fluence. The incident D ion energy ranges from 30 to 180 eV at a flux of 4 × 1021 D m-2 s-1 up to a fluence of 1025 D m-2. SEM images revealed a clear change of the surface morphology as functions of incident fluence and impinging energy. The mass loss results showed a decrease of the total sputtering yield of CLF-1 steel with increasing incident fluence by up to one order of magnitude. The total sputtering yield of CLF-1 steel after 7.2 × 1024 D m-2 deuterium plasma exposure reduced by a factor of 4 compared with that of pure iron, which can be attributed to the enrichment of W at the surface due to preferential sputtering of iron and chromium. After D plasma exposure, the total deuterium retention in CLF-1 steel samples measured by TDS decreased with increasing incident fluence and energy, and a clear saturation tendency as function of incident fluence or energy was also observed.

The deuterium inventory in ASDEX Upgrade

International Nuclear Information System (INIS)

Mayer, M.; Rohde, V.; Ramos, G; Vainonen-Ahlgren, E.; Likonen, J.; Herrmann, A.; Neu, R.

2007-01-01

The deuterium inventory in ASDEX Upgrade was determined by quantitative ion beam analysis techniques and SIMS for different discharge campaigns between the years 2002 and 2005. ASDEX Upgrade was a carbon dominated machine during this phase. Full poloidal sections of the lower and upper divertor tile surfaces, limiter tiles, gaps between divertor tiles, gaps between inner heat shield tiles and samples from remote areas below the roof baffle and in pump ducts were analysed, thus offering an exhaustive survey of all relevant areas in ASDEX Upgrade. Deuterium is mainly trapped on plasma-exposed surfaces of inner divertor tiles, where about 70% of the retained deuterium inventory is found. About 20% of the inventory is retained at or below the divertor roof baffle, and about 10% is observed in other areas, such as the outer divertor and in gaps between tiles. The long term deuterium retention is 3-4% of the total deuterium input. The obtained results are compared with gas balance measurements, and conclusions about tritium retention in ITER are made

Spherical cauliflower-like carbon dust formed by interaction between deuterium plasma and graphite target and its internal structure

Energy Technology Data Exchange (ETDEWEB)

Ohno, N. [Department of Energy Engineering and Science, Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)], E-mail: ohno@ees.nagoya-u.ac.jp; Yoshimi, M. [Department of Energy Engineering and Science, Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Tokitani, M. [National Institute for Fusion Science, Oroshi 322-6, Toki 509-5292 (Japan); Takamura, S. [Department of Electronics, Aichi Institute of Technology, Yakusa-cho, Toyota 470-0392 (Japan); Tokunaga, K.; Yoshida, N. [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan)

2009-06-15

Simulated experiments to produce carbon dust particles with cauliflower structure have been performed in a liner plasma device, NAGDIS-II by exposing high density deuterium plasma to a graphite sample (IG-430U). Formation of carbon dust depends on the surface temperature and the incident ion energy. At a surface temperature 600-700 K, a lot of isolated spherical dust particles are observed on the graphite target. The internal structure of an isolated dust particle was observed with Focused Ion Beam (FIB) system and Transmission Electron Microscope (TEM) in detail. FIB analysis clearly shows there exist honey-combed cell structure with thin carbon walls in the dust particle and the dust particle grows from the graphite surface. TEM image also shows that the dust particle is made of amorphous carbon with crystallized grains with diameters of 10-50 nm.

Energetics of semi-catalyzed-deuterium, light-water-moderated, fusion-fission toroidal reactors

International Nuclear Information System (INIS)

Jassby, D.L.; Towner, H.H.; Greenspan, E.; Schneider, A.; Misolovin, A.; Gilai, D.

1978-07-01

The semi-catalyzed-deuterium Light-Water Hybrid Reactor (LWHR) comprises a lithium-free light-water-moderated blanket with U 3 Si fuel driven by a deuterium-based fusion-neutron source, with complete burn-up of the tritium but almost no burn-up of the helium-3 reaction product. A one-dimensional model for a neutral-beam-driven tokamak plasma is used to determine the operating modes under which the fusion energy multiplication Q/sub p/ can be equal to or greater than 0.5. Thermonuclear, beam-target, and energetic-ion reactions are taken into account. The most feasible operating conditions for Q/sub p/ approximately 0.5 are tau/sub E/ = 2 to 4 x 10 14 cm -3 s, = 10 to 20 keV, and E/sub beam/ = 500 to 1000 keV, with approximately 40% of the fusion energy produced by beam-target reactions. Illustrative parameters of LWHRs are compared with those of an ignited D-T reactor

Laser-driven polarized sources of hydrogen and deuterium

International Nuclear Information System (INIS)

Young, L.; Holt, R.J.; Green, M.C.; Kowalczyk, R.S.

1988-01-01

A novel laser-driven polarized source of hydrogen and deuterium which operates on the principle of spin exchange optical pumping is described. The advantages of this method over conventional polarized sources for internal target experiments are presented. Technological difficulties which prevent ideal source operation are outlined along with proposed solutions. At present, the laser-driven polarized hydrogen source delivers 8 /times/ 10 16 atoms/s with a polarization (P/sub z/) of 24%. 9 refs., 2 figs

Deuterium trapping in tungsten

Science.gov (United States)

Poon, Michael

Tungsten is one of the primary material candidates being investigated for use in the first-wall of a magnetic confinement fusion reactor. An ion accelerator was used to simulate the type of ion interaction that may occur at a plasma-facing material. Thermal desorption spectroscopy (TDS) was the primary tool used to analyze the effects of the irradiation. Secondary ion mass spectroscopy (SIMS) was used to determine the distribution of trapped D in the tungsten specimen. The tritium migration analysis program (TMAP) was used to simulate thermal desorption profiles from the D depth distributions. Fitting of the simulated thermal desorption profiles with the measured TDS results provided values of the D trap energies. Deuterium trapping in single crystal tungsten was studied as a function of the incident ion fluence, ion flux, irradiation temperature, irradiation history, and surface impurity levels during irradiation. The results show that deuterium was trapped at vacancies and voids. Two deuterium atoms could be trapped at a tungsten vacancy, with trapping energies of 1.4 eV and 1.2 eV for the first and second D atoms, respectively. In a tungsten void, D is trapped as atoms adsorbed on the inner walls of the void with a trap energy of 2.1 eV, or as D2 molecules inside the void with a trap energy of 1.2 eV. Deuterium trapping in polycrystalline tungsten was also studied as a function of the incident fluence, irradiation temperature, and irradiation history. Deuterium trapping in polycrystalline tungsten also occurs primarily at vacancies and voids with the same trap energies as in single crystal tungsten; however, the presence of grain boundaries promotes the formation of large surface blisters with high fluence irradiations at 500 K. In general, D trapping is greater in polycrystalline tungsten than in single crystal tungsten. To simulate mixed materials comprising of carbon (C) and tungsten, tungsten specimens were pre-irradiated with carbon ions prior to D

Deuterium trapping in tungsten

International Nuclear Information System (INIS)

Poon, M.

2004-01-01

Tungsten is one of the primary material candidates being investigated for use in the first-wall of a magnetic confinement fusion reactor. An ion accelerator was used to simulate the type of ion interaction that may occur at a plasma-facing material. Thermal desorption spectroscopy (TDS) was the primary tool used to analyze the effects of the irradiation Secondary ion mass spectroscopy (SIMS) was used to determine the distribution of trapped D in the tungsten specimen. The tritium migration analysis program (TMAP) was used to simulate thermal desorption profiles from the D depth distributions. Fitting of the simulated thermal desorption profiles with the measured TDS results provided values of the D trap energies. . Deuterium trapping in single crystal tungsten was studied as a function of the incident ion fluence, ion flux, irradiation temperature, irradiation history, and surface impurity levels during irradiation The results show that deuterium was trapped at vacancies and voids. Two deuterium atoms could be trapped at a tungsten vacancy, with trapping energies of 1.4 eV and 1.2 eV for the first and second D atoms, respectively. In a tungsten void, D is trapped as atoms adsorbed on the inner walls of the void with a trap energy of 2.1 eV, or as D 2 molecules inside the void with a trap energy of 1.2 eV. . Deuterium trapping in polycrystalline tungsten was also studied as a function of the incident fluence, irradiation temperature, and irradiation history. Deuterium trapping in polycrystalline tungsten also occurs primarily at vacancies and voids with the same trap energies as in single crystal tungsten; however, the presence of grain boundaries promotes the formation of large surface blisters with high fluence irradiations at 500 K. In general, D trapping is greater in polycrystalline tungsten than in single crystal tungsten. To simulate mixed materials comprising of carbon (C) and tungsten, tungsten specimens were pre-irradiated with carbon ions prior to D

Deuterium trapping in tungsten

Energy Technology Data Exchange (ETDEWEB)

Poon, M

2004-07-01

Tungsten is one of the primary material candidates being investigated for use in the first-wall of a magnetic confinement fusion reactor. An ion accelerator was used to simulate the type of ion interaction that may occur at a plasma-facing material. Thermal desorption spectroscopy (TDS) was the primary tool used to analyze the effects of the irradiation Secondary ion mass spectroscopy (SIMS) was used to determine the distribution of trapped D in the tungsten specimen. The tritium migration analysis program (TMAP) was used to simulate thermal desorption profiles from the D depth distributions. Fitting of the simulated thermal desorption profiles with the measured TDS results provided values of the D trap energies. . Deuterium trapping in single crystal tungsten was studied as a function of the incident ion fluence, ion flux, irradiation temperature, irradiation history, and surface impurity levels during irradiation The results show that deuterium was trapped at vacancies and voids. Two deuterium atoms could be trapped at a tungsten vacancy, with trapping energies of 1.4 eV and 1.2 eV for the first and second D atoms, respectively. In a tungsten void, D is trapped as atoms adsorbed on the inner walls of the void with a trap energy of 2.1 eV, or as D{sub 2} molecules inside the void with a trap energy of 1.2 eV. . Deuterium trapping in polycrystalline tungsten was also studied as a function of the incident fluence, irradiation temperature, and irradiation history. Deuterium trapping in polycrystalline tungsten also occurs primarily at vacancies and voids with the same trap energies as in single crystal tungsten; however, the presence of grain boundaries promotes the formation of large surface blisters with high fluence irradiations at 500 K. In general, D trapping is greater in polycrystalline tungsten than in single crystal tungsten. To simulate mixed materials comprising of carbon (C) and tungsten, tungsten specimens were pre-irradiated with carbon ions prior to D

Solid deuterium centrifuge pellet injector

International Nuclear Information System (INIS)

Foster, C.A.

1982-01-01

Pellet injectors are needed to fuel long pulse tokamak plasmas and other magnetic confinement devices. For this purpose, an apparatus has been developed that forms 1.3-mm-diam pellets of frozen deuterium at a rate of 40 pellets per second and accelerates them to a speed of 1 km/s. Pellets are formed by extruding a billet of solidified deuterium through a 1.3-mm-diam nozzle at a speed of 5 cm/s. The extruding deuterium is chopped with a razor knife, forming 1.3-mm right circular cylinders of solid deuterium. The pellets are accelerated by synchronously injecting them into a high speed rotating arbor containing a guide track, which carries them from a point near the center of rotation to the periphery. The pellets leave the wheel after 150 0 of rotation at double the tip speed. The centrifuge is formed in the shape of a centrifugal catenary and is constructed of high strength KEVLAR/epoxy composite. This arbon has been spin-tested to a tip speed of 1 km/s

Solid deuterium centrifuge pellet injector

International Nuclear Information System (INIS)

Foster, C.A.

1983-01-01

Pellet injectors are needed to fuel long pulse tokamak plasmas and other magnetic confinement devices. For this purpose, an apparatus has been developed that forms 1.3-mm-diam pellets of frozen deuterium at a rate of 40 pellets per second and accelerates them to a speed of 1 km/s. Pellets are formed by extruding a billet of solidified deuterium through a 1.3-mm-diam nozzle at a speed of 5 cm/s. The extruding deuterium is chopped with a razor knife, forming 1.3-mm right circular cylinders of solid deuterium. The pellets are accelerated by synchronously injecting them into a high speed rotating arbor containing a guide track, which carries them from a point near the center of rotation to the periphery. The pellets leave the wheel after 150 0 of rotation at double the tip speed. The centrifuge is formed in the shape of a centrifugal catenary and is constructed of high strength Kevlar/epoxy composite. This arbor has been spin-tested to a tip speed of 1 km/s

Measurement of scattering cross sections of liquid and solid hydrogen, deuterium and deuterium hydride for thermal neutrons

International Nuclear Information System (INIS)

Seiffert, W.D.

1984-01-01

The scattering cross sections for liquid and solid normal hydrogen, para-hydrogen, deuterium and deuterium hydride were measured for thermal neutrons at various temperatures. Solid samples of para-hydrogen exhibit distinct Bragg scattering. Liquid samples of deuterium and para-hydrogen also exhibit distinct coherence phenomena, which is indicative of strong local ordering of the molecules. In para-hydrogen and deuterium hydride, the threshold for scattering with excitation of rotations is distinctly visible. The positions of the thresholds show that the molecules in liquid hydrogen are not unhindered in their movement. After the beginning of the rotational excitation the scattering cross sections of liquid and solid para-hydrogen have different shapes which is to be explained by the differences in the dynamics of the liquid and the solid specimen. 22 references

Retention and features of deuterium detrapping from radiation-induced damages in steels

International Nuclear Information System (INIS)

Tolstolutskaya, G.D.; Ruzhytskiy, V.V.; Karpov, S.A.; Kopanets, I.E.

2009-01-01

The accelerators and ion-beam analysis techniques are used for simulation of displacement damage and detailed investigation of distribution profiles of damage and impurity gas atoms (especially helium and hydrogen) in the irradiation of targets for a wide ranges of doses and particle energies. The influence of preimplanted helium and heavy ion-induced damage on deuterium trapping in austenitic and ferritic/martensitic steels was studied. The results obtained for 18Cr10NiTi stainless steel show that ion-implanted deuterium is weakly trapped by defects produced in 5 keV D + displacement cascades. The effective trapping temperature interval is between 300 and 600 K. The characteristics of trapping and the temperature range of hydrogen isotopes retention in traps formed by prior implantation of helium depend on the concentration of implanted helium and on the type of defects developed. The formation of helium bubbles in 18Cr10NiTi steel causes an order of magnitude increase in the content of retained deuterium atoms in the range of temperature 300-600 K and extends the interval of effective trapping temperatures to 1000 K. Energetic heavy-ion irradiation (1.4 MeV Ar + ) has been used for modeling defect cluster formation under displacement cascade conditions to simulate fusion reactor environments. It was found that retention of hydrogen and deuterium strongly increased in this case. It is shown that the presence of a surface-passive film considerably shifts the gas release interval to higher temperatures and reduces the deuterium surface recombination coefficient by several orders of magnitude.

Method for measuring deuterium in erbium deuteride films

International Nuclear Information System (INIS)

Brangan, J.R.; Thornberg, S.M.; Keenan, M.R.

1997-09-01

Determining the quantity of deuterium in an erbium deuteride (ErD 2 ) film is essential for assessing the quality of the hydriding process but is a challenging measurement to make. First, the ideal gas law cannot be applied directly due to high temperature (950 degrees C) and low temperature (25 degrees C) regions in the same manifold. Additionally, the metal hydride does not release all of the deuterium rapidly upon heating and metal evaporation occurs during extended heating periods. Therefore, the method developed must provide a means to compensate for temperature inhomogeneities and the amount of deuterium retained in the metal film while heating for a minimal duration. This paper presents two thermal desorption methods used to evaluate the kinetics and equilibria of the deuterium desorption process at high temperatures (950 degrees C). Of primary concern is the evaluation of the quantity of deuterium remaining in these films at the high temperature. A multiple volume expansion technique provided insight into the kinetics of the deuterium evolution and metal evaporation from the film. Finally a repeated pump-down approach yielded data that indicated approximately 10% of the deuterium is retained in the metal film at 950 degrees C and approximately 1 Torr pressure. When the total moles of deuterium determined by this method were divided by the moles of erbium determined by ICP/AES, nearly stochiometric values of 2:1 were obtained for several erbium dideuteride films. Although this work presents data for erbium and deuterium, these methods are applicable to other metal hydrides as well

Counter-diffusion and -permeation of deuterium and hydrogen through metals

Energy Technology Data Exchange (ETDEWEB)

Kizu, Kaname; Tanabe,; Tetsuo, [Nagoya Univ. (Japan)

1998-03-01

The first experiments for counter-diffusion and -permeation of deuterium and hydrogen through palladium were performed. Deuterium permeation rates against D{sub 2} pressure were measured under the condition where hydrogen permeated to opposite direction by supplying H{sub 2} gas at the permeated side of D{sub 2}. It was found that not a small amount of deuterium was clearly permeated even if the deuterium pressure was much smaller than the hydrogen pressure. Deuterium permeation rate was gradually reduced by increasing the counter H permeation. The deuterium permeation rate under the counter H permeation is well represented by a simple model in which the ratio of the deuterium permeation rates with and without the counter H permeation was proportional to the fractional concentration of deuterium in the bulk. As increasing the hydrogen counter flow, however, the deuterium permeation rate deviates from the model. This means that adsorption (absorption) of D{sub 2} from gas phase is inhibited and surface recombination of deuterium is blocked by hydrogen. (author)

Additive quark model and double scattering of pions and protons in deuterium

International Nuclear Information System (INIS)

Bialas, A.; Czyz, W.; Kisielewska, D.

1981-01-01

It is shown that the additive quark model is compatible with the data on double scattering of pions and protons in deuterium. The cross-section for interaction of the hadrons created in the first collision with the second nucleon of the target is determined to be 20-25 mb. (author)

Measurement of the temperature dependence of the ddμ-molecule formation rate in gaseous deuterium at the pressures 1.5 and 0.4 kbar

International Nuclear Information System (INIS)

Bystritskij, V.M.; Dzhelepov, V.P.; Zinov, V.G.

1990-01-01

In the experiment with a gaseous deuterium target of high pressure on the muon beam of the JINR phasotron the temperature dependence of the ddμ-molecule formation rate (λ ddμ ) has been measured. Measurements have been performed with liquid deuterium at the temperature T=20.3 K and with gaseous deuterium at pressure 1500 and 400 bar in the temperature region T=49-300 K. It is found that the value λ ddμ does not depend on the deuterium density for each temperature. The obtained results are in fairly good agreement with theory and with the data of other experiments made with deuterium of sufficiently (one-two order) lower density. 22 refs.; 3 figs.; 1 tab

Desorption dynamics of deuterium in CuCrZr alloy

Science.gov (United States)

Thi Nguyen, Lan Anh; Lee, Sanghwa; Noh, S. J.; Lee, S. K.; Park, M. C.; Shu, Wataru; Pitcher, Spencer; Torcy, David; Guillermain, David; Kim, Jaeyong

2017-12-01

Desorption behavior of deuterium (D2) in CuCrZr alloy was investigated considering sample thickness, loading and baking temperature of deuterium followed by the ITER scopes. Cylindrical specimens of 1, 3, 5 mm thick with 4 mm diameter were exposed to deuterium at a pressure of 25 bar at 120, 240 and 350 °C for 24 h, then baked at 800 °C in a vacuum chamber maintained at a pressure lower than 10-7 Torr. Deuterium desorption characteristics such as desorption rate and amount of deuterium in the sample were estimated by analyzing the desorption peaks monitored with a residual gas analyzer (RGA), and the trapping energy of deuterium was calculated using thermal desorption spectroscopy (TDS). Secondary ion mass spectroscopy (SIMS) results showed that deuterium atoms embedded in the sample at a depth of less than 15 μm and desorbed as low as 400 °C. All absorbed deuterium atoms in the specimen were completely retrieved by dynamic pumping at 800 °C in 15 min. The desorption rate of deuterium per unit area was inversely proportional to the increment of the thickness of the sample, and was proportional to the loading temperature. Based on the assumption that a uniform distribution of interstitial sites for deuterium follows the Femi-Dirac statistics, the result of TDS demonstrated that the CuCrZr alloy has two types of trapping energies, which were estimated to be 62 and 79 kJ/mol.

Beam splitting to improve target life in neutron generators

International Nuclear Information System (INIS)

Farrell, J.P.

1976-01-01

In a neutron generator in which a tritium-titanium target is bombarded by a deuterium ion beam, the target half-life is increased by separating the beam with a weak magnetic field to provide three separate beams of atomic, diatomic, and triatomic deuterium ions which all strike the target at different adjacent locations. Beam separation in this manner eliminates the problem of one type ion impairing the neutron generating efficiency of other type ions, thereby effecting more efficient utilization of the target material

Method for nondestructive fuel assay of laser fusion targets

Science.gov (United States)

Farnum, Eugene H.; Fries, R. Jay

1976-01-01

A method for nondestructively determining the deuterium and tritium content of laser fusion targets by counting the x rays produced by the interaction of tritium beta particles with the walls of the microballoons used to contain the deuterium and tritium gas mixture under high pressure. The x rays provide a direct measure of the tritium content and a means for calculating the deuterium content using the initial known D-T ratio and the known deuterium and tritium diffusion rates.

A laser-driven source of polarized hydrogen and deuterium

International Nuclear Information System (INIS)

Young, L.; Holt, R.J.; Gilman, R.A.; Kowalczyk, R.; Coulter, K.

1989-01-01

A novel laser-driven polarized source of hydrogen and deuterium which operates on the principle of spin-exchange optical pumping is being developed. This source is designed to operate as an internal target in an electron storage ring for fundamental studies of spin-dependent structure of nuclei. It has the potential to exceed the flux from existing conventional sources (3 times 10 16/ s) by an order of magnitude. Currently, the source delivers hydrogen at a flux of 8 times 10 16 atoms/s with an atomic polarization of 24% and deuterium at 6 times 10 16 atoms/s with a polarization of 29%. Technical obstacles which have been overcome, with varying degrees of success are complete Doppler-coverage in the optical-pumping stage without the use of a buffer gas, wall-induced depolarization and radiation-trapping. Future improvements should allow achievement of the design goals of 4 times 10 17 atoms/s with a polarization of 50%. 8 refs., 2 figs

Method of deuterium isotope separation using ethylene and ethylene dichloride

International Nuclear Information System (INIS)

Benson, S.W.

1982-01-01

Compounds enriched in deuterium may be obtained from ethylene, vinyl chloride, 1,2-dichloroethane, or propylene by laser isotope separation. Normal molecules of these organic compounds are exposed to infrared laser radiation of a suitable wavelength. Substantially all of the deuterium-containing molecules exposed to the laser can be selectively dissociated and the deuterium-containing products separated from the starting material and other reaction products. The deuterium-containing molecules can be burned to form water with an enriched deuterium content, or pyrolized to form hydrogen gas enriched in deuterium

The hydrogen and deuterium concentrations in chondrites

International Nuclear Information System (INIS)

Robert, F.; Merlivat, L.

1978-01-01

Water and isotopic concentration of H 2 O + are reported. It shows a correlation between the water, the deuterium concentrations and the petrologic types of chondrites. The Chainpur meteorite has been divided into several mineralogical fractions and the results are reported. The results of Orgueil are also reported. The correlation shows that as the sulfate content increases, the water and deuterium contents decrease. The terrestrial contamination is discussed and possible deuterium variation models are presented

Deuterium behavior in first-wall materials for nuclear fusion

International Nuclear Information System (INIS)

Bernard, E.

2012-01-01

Plasma-wall interactions play an important part while choosing materials for the first wall in future fusion reactors. Moreover, the use of tritium as a fuel will impose safety limits regarding the total amount present in the tokamak. Previous analyses of first-wall samples exposed to fusion plasma highlighted an in-bulk migration of deuterium (as an analog to tritium) in carbon materials. Despite its limited value, this retention is problematic: contrary to co-deposited layers, it seems very unlikely to recover easily the deuterium retained in such a way. Because of the difficult access to in situ samples, most published studies on the subject were carried out using post-mortem sample analysis. In order to access to the dynamic of the phenomenon and come apart potential element redistribution during storage, we set up a bench intended for simultaneous low-energy ion implantation, reproducing the deuterium interaction with first-wall materials, and high-energy micro beam analysis. Nuclear reaction analysis performed at the micrometric scale (μNRA) allows to characterize deuterium repartition profiles in situ. This analysis technique was confirmed to be non-perturbative of the mechanisms studied. We observed on the experimental data set that the material surface (0-1 μm) display a high and nearly constant deuterium content, with a uniform distribution. On the contrary, in-bulk deuterium (1-11 μm) localizes in preferential trapping sites related to the material microstructure. In-bulk deuterium inventory seems to increase with the incident fluence, in spite of the wide data scattering attributed to the structure variation of studied areas. Deuterium saturation at the surface as well as in-depth migration are instantaneous; in-vacuum storage leads to a small deuterium global desorption. Observations made via μNRA were coupled with results from other characterization techniques. X-ray μtomography allowed to identify porosities as the preferential trapping sites

Method for nondestructive fuel assay of laser fusion targets

International Nuclear Information System (INIS)

Farnum, E.H.; Fries, R.J.

1976-01-01

A method is described for nondestructively determining the deuterium and tritium content of laser fusion targets by counting the x rays produced by the interaction of tritium beta particles with the walls of the microballoons used to contain the deuterium and tritium gas mixture under high pressure. The x rays provide a direct measure of the tritium content and a means for calculating the deuterium content using the initial known D-T ratio and the known deuterium and tritium diffusion rates

Deuterium retention in liquid lithium

International Nuclear Information System (INIS)

Baldwin, M.J.; Doerner, R.P.; Luckhardt, S.C.; Conn, R.W.

2002-01-01

Measurements of deuterium retention in samples of lithium exposed in the liquid state to deuterium plasma are reported. Retention was measured as a function of plasma ion dose in the range 6x10 19 -4x10 22 D atoms and exposure temperature between 523 and 673 K using thermal desorption spectrometry. The results are consistent with the full uptake of all deuterium ions incident on the liquid metal surface and are found to be independent of the temperature of the liquid lithium over the range explored. Full uptake, consistent with very low recycling, continues until the sample is volumetrically converted to lithium deuteride. This occurs for exposure temperatures where the gas pressure during exposure was both below and slightly above the corresponding decomposition pressure for LiD in Li. (author)

Nuclear processes in deuterium/natural hydrogen-metal systems

International Nuclear Information System (INIS)

Zelensky, V.F.

2013-01-01

The survey presents the analysis of the phenomena taking place in deuterium - metal and natural hydrogen - metal systems under cold fusion experimental conditions. The cold fusion experiments have shown that the generation of heat and helium in the deuterium-metal system without emission of energetic gamma-quanta is the result of occurrence of a chain of chemical, physical and nuclear processes observed in the system, culminating in both the fusion of deuterium nuclei and the formation of a virtual, electron-modified excited 4He nucleus. The excitation energy of the helium nucleus is transferred to the matrix through emission of conversion electrons, and that, under appropriate conditions, provides a persistent synthesis of deuterium. The processes occurring in the deuterium/natural hydrogen - metal systems have come to be known as chemonuclear DD- and HD-fusion. The mechanism of stimulation of weak interaction reactions under chemonuclear deuterium fusion conditions by means of strong interaction reactions has been proposed. The results of numerous experiments discussed in the survey bear witness to the validity of chemonuclear fusion. From the facts discussed it is concluded that the chemonuclear deuterium fusion scenario as presented in this paper may serve as a basis for expansion of deeper research and development of this ecologically clean energy source. It is shown that the natural hydrogen-based system, containing 0.015% of deuterium, also has good prospects as an energy source. The chemonuclear fusion processes do not require going beyond the scope of traditional physics for their explanation

Catalyzed deuterium fueled tokamak reactors

International Nuclear Information System (INIS)

Southworth, F.H.

1977-01-01

Catalyzed deuterium fuel presents several advantages relative to D-T. These are, freedom from tritium breeding, high charged particle power fraction and lowered neutron energy deposition in the blanket. Higher temperature operation, lower power densities and increased confinement are simultaneously required. However, the present study has developed designs which have capitalized upon the advantages of catalyzed deuterium to overcome the difficulties associated with the fuel while obtaining high efficiency

Deuterium as a tracer in coal liquefaction. Pt. 1

International Nuclear Information System (INIS)

Wilson, M.A.; Collin, P.J.; Barron, P.F.; Vassallo, A.M.

1982-01-01

Deuterium has been used to trace the pathways by which hydrogen reacts with an Australian bituminous coal (Liddell) in the presence of a nickel/molybdenum catalyst. The results show that at 400 0 C extensive scrambling of hydrogen and deuterium occurs among aromatic and α to aromatic aliphatic hydrogen and deuterium substituents. Deuterium can enter all structural groups in both asphaltene and hexane-soluble fractions of the coal-derived liquids, but it enters aromatic and α to aromatic groups in preference to alkyl groups remote from aromatic rings. Thus the results indicate that hydrogen atoms are very mobile during coal hydrogenation. Deuterium from deuterium oxide generated during conversion can also be incorporated into the coal-derived liquids. During coal hydrogenation, the eventual fate of much of the hydrogen in the gas phase is to substitute for hydrogen already in the coal. (Auth.)

In-medium modification of pion-pairs on deuterium

Energy Technology Data Exchange (ETDEWEB)

Lugert, Stefan

2007-11-23

In this thesis the quasi free photo production of pion pairs on bound nucleons {gamma}+A{yields} {pi}{pi}(A-1)+N is analyzed for liquid Deuterium. A pioneering experiment with a photon beam was performed by the TAPS collaboration at the accelerator facility MAMI-B in Mainz in 1999. This measurement observed an invariant mass shift of the isoscalar {pi}{sup 0}{pi}{sup 0} channel with increasing atomic number as well. Due to the poor statistics, the significance of the data was however limited. The experiment described in this work reached a much higher statistical significance, allowing a review of the old data. In this experiment, the TAPS detector was used as a forward wall in combination with the Crystal Ball detector to achieve almost the complete 4{pi} solid angle coverage for particle detection at the MAMI accelerator facility. The installation of the experimental setup started at the end of 2003. The new readout electronics for the BaF{sub 2} crystals was used for the first time. Between June 2004 and April 2005 measurements on several targets were performed, including the lD{sub 2} data which has been analyzed in this work. The analysis of the Deuterium data is an essential contribution to understanding the ongoing processes for two reasons. Firstly, there is the possibility to compare the solid targets and Hydrogen to the lightest nucleus having Fermi motion included but the lowest possible nuclear volume, the Deuterium. For the second reason, there are no data for the mass differential cross section on the neutron available for the mentioned channels. Analyzing the Deuterium data and subtracting the published proton data, the cross section on the neutron gets accessible. An essential question for the theory is whether the cross section on neutron and proton are the same or how much they differ in the relevant energy regime. To determine the absolute cross section, the efficiency of the detector system is required. To provide this efficiency, I also

In-medium modification of pion-pairs on deuterium

International Nuclear Information System (INIS)

Lugert, Stefan

2007-01-01

In this thesis the quasi free photo production of pion pairs on bound nucleons γ+A→ ππ(A-1)+N is analyzed for liquid Deuterium. A pioneering experiment with a photon beam was performed by the TAPS collaboration at the accelerator facility MAMI-B in Mainz in 1999. This measurement observed an invariant mass shift of the isoscalar π 0 π 0 channel with increasing atomic number as well. Due to the poor statistics, the significance of the data was however limited. The experiment described in this work reached a much higher statistical significance, allowing a review of the old data. In this experiment, the TAPS detector was used as a forward wall in combination with the Crystal Ball detector to achieve almost the complete 4π solid angle coverage for particle detection at the MAMI accelerator facility. The installation of the experimental setup started at the end of 2003. The new readout electronics for the BaF 2 crystals was used for the first time. Between June 2004 and April 2005 measurements on several targets were performed, including the lD 2 data which has been analyzed in this work. The analysis of the Deuterium data is an essential contribution to understanding the ongoing processes for two reasons. Firstly, there is the possibility to compare the solid targets and Hydrogen to the lightest nucleus having Fermi motion included but the lowest possible nuclear volume, the Deuterium. For the second reason, there are no data for the mass differential cross section on the neutron available for the mentioned channels. Analyzing the Deuterium data and subtracting the published proton data, the cross section on the neutron gets accessible. An essential question for the theory is whether the cross section on neutron and proton are the same or how much they differ in the relevant energy regime. To determine the absolute cross section, the efficiency of the detector system is required. To provide this efficiency, I also developed the MonteCarlo simulation using a

Predicting big bang deuterium

Energy Technology Data Exchange (ETDEWEB)

Hata, N.; Scherrer, R.J.; Steigman, G.; Thomas, D.; Walker, T.P. [Department of Physics, Ohio State University, Columbus, Ohio 43210 (United States)

1996-02-01

We present new upper and lower bounds to the primordial abundances of deuterium and {sup 3}He based on observational data from the solar system and the interstellar medium. Independent of any model for the primordial production of the elements we find (at the 95{percent} C.L.): 1.5{times}10{sup {minus}5}{le}(D/H){sub {ital P}}{le}10.0{times}10{sup {minus}5} and ({sup 3}He/H){sub {ital P}}{le}2.6{times}10{sup {minus}5}. When combined with the predictions of standard big bang nucleosynthesis, these constraints lead to a 95{percent} C.L. bound on the primordial abundance deuterium: (D/H){sub best}=(3.5{sup +2.7}{sub {minus}1.8}){times}10{sup {minus}5}. Measurements of deuterium absorption in the spectra of high-redshift QSOs will directly test this prediction. The implications of this prediction for the primordial abundances of {sup 4}He and {sup 7}Li are discussed, as well as those for the universal density of baryons. {copyright} {ital 1996 The American Astronomical Society.}

Equilibrium deuterium isotope effect of surprising magnitude

International Nuclear Information System (INIS)

Goldstein, M.J.; Pressman, E.J.

1981-01-01

Seemingly large deuterium isotope effects are reported for the preference of deuterium for the α-chloro site to the bridgehead or to the vinyl site in samples of anti-7-chlorobicyclo[4.3.2]undecatetraene-d 1 . Studies of molecular models did not provide a basis for these large equilibrium deuterium isotope effects. The possibility is proposed that these isotope effects only appear to be large for want of comparison with isotope effects measured for molecules that might provide even greater contrasts in local force fields

Deuterium trapping in carbon fiber composites under high fluence

International Nuclear Information System (INIS)

Airapetov, A.A.; Begrambekov, L.B.; Kuzmin, A.A.; Shigin, P.A.; Zakharov, A.M.

2010-01-01

The paper is devoted to investigation of deuterium trapping in CFC, dance graphite MPG-8 and pyrolytic graphite (PG) under plasma ion- and electron irradiation. Number of specific features of deuterium trapping and retention under plasma ion and electron irradiation is presented and discussed. In particular it is shown that 1) deuterium trapping takes place even when energy of impinging ions approaches zero; 2) deuterium is trapped under irradiation by plasma electrons; 3) under irradiation at equal fluences deuterium trapping is higher, when ion flux is smaller. High energy ion penetrating the surfaces are trapped in the traps created at the expense of their kinetic energy. The process may be named 'kinetic trapping'. Under low energy (smaller than 200 eV) electron and/or ion irradiation the energy of inelastic interaction on the surface provides creation of active centers, which initiate dissociation of deuterium sorbed on the surface, penetration of deuterium atoms into graphite and their trapping in specific low energy traps. The term 'potential trapping' is proposed for this type of trapping. Under high energy irradiation such atoms can fill the traps formed through kinetic mechanism. Origination of moveable deuterium atoms from the layer of surface sorption seems to be time dependent process and it is a reason of increase of trapping along with irradiation time. New features of deuterium trapping and retention in graphite evaluated in this study offer new opportunities for analysis and correct estimation of hydrogen isotope trapping and retention in tokamaks having graphite tiles. (authors)

Deuterium fractionation in dense interstellar clouds

International Nuclear Information System (INIS)

Millar, T.J.; Bennett, A.; Herbst, E.

1989-01-01

The time-dependent gas-phase chemistry of deuterium fractionation in dense interstellar clouds ranging in temperature between 10 and 70 K was investigated using a pseudo-time-dependent model similar to that of Brown and Rice (1986). The present approach, however, considers much more complex species, uses more deuterium fractionation reactions, and includes the use of new branching ratios for dissociative recombinations reactions. Results indicate that, in cold clouds, the major and most global source of deuterium fractionation is H2D(+) and ions derived from it, such as DCO(+) and H2DO(+). In warmer clouds, reactions of CH2D(+), C2HD(+), and associated species lead to significant fractionation even at 70 K, which is the assumed Orion temperature. The deuterium abundance ratios calculated at 10 K are consistent with those observed in TMC-1 for most species. However, a comparison between theory and observatiom for Orion, indicates that, for species in the ambient molecular cloud, the early-time results obtained with the old dissociative recombination branching ratios are superior if a temperature of 70 K is utilized. 60 refs

Deuterium fractionation in dense interstellar clouds

Science.gov (United States)

Millar, T. J.; Bennett, A.; Herbst, Eric

1989-05-01

The time-dependent gas-phase chemistry of deuterium fractionation in dense interstellar clouds ranging in temperature between 10 and 70 K was investigated using a pseudo-time-dependent model similar to that of Brown and Rice (1986). The present approach, however, considers much more complex species, uses more deuterium fractionation reactions, and includes the use of new branching ratios for dissociative recombinations reactions. Results indicate that, in cold clouds, the major and most global source of deuterium fractionation is H2D(+) and ions derived from it, such as DCO(+) and H2DO(+). In warmer clouds, reactions of CH2D(+), C2HD(+), and associated species lead to significant fractionation even at 70 K, which is the assumed Orion temperature. The deuterium abundance ratios calculated at 10 K are consistent with those observed in TMC-1 for most species. However, a comparison between theory and observatiom for Orion, indicates that, for species in the ambient molecular cloud, the early-time results obtained with the old dissociative recombination branching ratios are superior if a temperature of 70 K is utilized.

Deuterium desorption from tungsten using laser heating

Directory of Open Access Journals (Sweden)

J.H. Yu

2017-08-01

Full Text Available Retention and desorption of hydrogenic species need to be accurately modeled to predict the tritium inventory of next generation fusion devices, which is needed both for tritium fuel recovery and for tritium safety concerns. In this paper, experiments on thermal desorption of deuterium from intrinsic polycrystalline tungsten defects using laser heating are compared to TMAP-7 modeling. The samples during deuterium plasma exposure were at a temperature of 373K for this benchmark study with ion fluence of 0.7–1.0 ×1024Dm−2. Following plasma exposure, a fiber laser (λ= 1100nm heated the samples to peak surface temperatures ranging from ∼500 to 1400K with pulse widths from 10ms to 1s, and 1 to 10 pulses applied to each sample. The remaining deuterium retention was measured using temperature programmed desorption (TPD. Results show that > 95% of deuterium is desorbed when the peak surface temperature reached ∼950K for > 1s. TMAP-7 is used to predict deuterium desorption from tungsten for a range of surface temperatures and heating durations, and is compared to previous work on desorption from beryllium codeposits.

Deuterium release from Li-D films exposed to atmospheric gases

Energy Technology Data Exchange (ETDEWEB)

Gasparyan, Yu. M., E-mail: YMGasparyan@mephi.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); Popkov, A.S.; Krat, S.A.; Pisarev, A.A.; Vasina, Ya. A. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); Lyublinski, I.E. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); JSC “Red Star”, Electrolitniy proezd 1a, Moscow (Russian Federation); Vertkov, A.V. [JSC “Red Star”, Electrolitniy proezd 1a, Moscow (Russian Federation)

2017-04-15

Highlights: • The major part of deuterium desorbs from Li-D films in a very sharp peak at 670–710 K. • Exposure on air leads to intensive deuterium release from the Li-D film at room temperature. • Interaction with water vapor plays a major role in deuterium release from lithium films in the air. - Abstract: Deuterium release from Li-D films co-deposited on a Mo substrate at room temperature in magnetron discharge was investigated by means of thermal desorption spectroscopy. The deuterium concentration in the films was estimated to be D/Li = (14 ± 4)%. TDS from Li-D films just after co-deposition had a sharp peak at 670–710 K. Exposure of deposited Li-D films in the air at room temperature led to deuterium release. Comparison of release in air, water vapor, nitrogen, and oxygen demonstrated that water plays a major role in deuterium release in the air at low temperatures.

SAIDE: A Semi-Automated Interface for Hydrogen/Deuterium Exchange Mass Spectrometry.

Science.gov (United States)

Villar, Maria T; Miller, Danny E; Fenton, Aron W; Artigues, Antonio

2010-01-01

Deuterium/hydrogen exchange in combination with mass spectrometry (DH MS) is a sensitive technique for detection of changes in protein conformation and dynamics. Since temperature, pH and timing control are the key elements for reliable and efficient measurement of hydrogen/deuterium content in proteins and peptides, we have developed a small, semiautomatic interface for deuterium exchange that interfaces the HPLC pumps with a mass spectrometer. This interface is relatively inexpensive to build, and provides efficient temperature and timing control in all stages of enzyme digestion, HPLC separation and mass analysis of the resulting peptides. We have tested this system with a series of standard tryptic peptides reconstituted in a solvent containing increasing concentration of deuterium. Our results demonstrate the use of this interface results in minimal loss of deuterium due to back exchange during HPLC desalting and separation. For peptides reconstituted in a buffer containing 100% deuterium, and assuming that all amide linkages have exchanged hydrogen with deuterium, the maximum loss of deuterium content is only 17% of the label, indicating the loss of only one deuterium molecule per peptide.

Long Term Retention of Deuterium and Tritium in Alcator C-Mod

International Nuclear Information System (INIS)

FIORE, C.; LABOMBARD, B.; LIPSCHULTZ, B.; PITCHER, C.S.; SKINNER, C.H.; WAMPLER, WILLIAM R.

1999-01-01

We estimate the total in-vessel deuterium retention in Alcator C-Mod from a run campaign of about 1090 plasmas. The estimate is based on measurements of deuterium retained on 22 molybdenum tiles from the inner wall and divertor. The areal density of deuterium on the tiles was measured by nuclear reaction analysis. From these data, the in-vessel deuterium inventory is estimated to be about 0.1 gram, assuming the deuterium coverage is toroidally symmetric. Most of the retained deuterium is on the walls of the main plasma chamber, only about 2.5% of the deuterium is in the divertor. The D coverage is consistent with a layer saturated by implantation with ions and charge-exchange neutrals from the plasma. This contrasts with tokamaks with carbon plasma-facing components (PFC's) where long-term retention of tritium and deuterium is large and mainly in the divertor due to codeposition with carbon eroded by the plasma. The low deuterium retention in the C-Mod divertor is mainly due to the absence of carbon PFC's in C-Mod and the low erosion rate of Mo

Compared studies of natural and artificial deuterium depleted water

International Nuclear Information System (INIS)

Butnaru, Gallia; Mihacea, Sorina; Sirbovan, Alina; Butnariu, H.; Titescu, Gh.

2001-01-01

The biological influence of the deuterium on animals was studied insensitively in the last years. When animal cell cultures were analyzed it turned out an inhibition of the development, due to the reduced deuterium concentration. In the in vivo experiments a decreasing of the number of tumoral cells was pointed out when performing the depleted water treatment. It is obvious that the presence of deuterium in water is necessary for the development, especially for the tumoral cell proliferation. The aim of this work was to establish influence of the natural and artificial deuterium depleted water on the vegetal organisms development. For this purpose, the developmental stages of Lactuca sativa L. growth were followed. The experimental data were compared with the data obtained with distilled water. The birch, wine sap and some fruit juices are considered 'natural depleted' water sources because their deuterium content is smaller in comparison to natural water (D 2 =150 ppm). The effect of artificial deuterium depleted water (29 ppm D 2 ) was analyzed in comparison to three types of wine saps, which also have a reduced deuterium concentration (125-130 ppm D 2 ). If the deuterium depleted water was used, the germination percent and the root and shoot length were higher compared to control in the first stages. In wine sap it had a negative effect on germination and development. After three days the plants were transferred to soil and their development was followed. The foliage area was larger for all of the experimental variants compared to control. The differences were without significance when deuterium depleted water was tested but they were high and very significant in case of wine sap. The experiment pointed out a stimulative effect of the artificial deuterium depleted water. In case of wine sap the effect was negative when the contact was direct, but the growth was stimulated after the stress cessation. The first ontogenetic stages were represented by direct action

Deuterium isotope effects on the ring inversion equilibrium in cyclohexane: the A value of deuterium and its origin

International Nuclear Information System (INIS)

Anet, F.A.L.; Kopelevich, M.

1986-01-01

It has been reported recently that the deuterium in cyclohexane-d 1 prefers the equatorial over the axial position by about 200 J/mol (i.e., ca. 50 cal/mol), as shown by three different kinds of NMR measurements. Such an isotope effect is unexpectedly large, and this has led the authors to reinvestigate the problem using Saunder's isotopic perturbation method. The authors thereby established that the free energy difference (the A value for deuterium) is 6.3 +/- 1.5 cal/mol, with deuterium more stable equatorial than axial. This value is supported by molecular mechanics calculations based in part on experimental vibrational frequencies. 17 references, 1 figure

Development and testing of a deuterium gas target assembly for neutron production via the H-2(d,n)He-3 reaction at a low-energy accelerator facility

International Nuclear Information System (INIS)

Feautrier, D.; Smith, D.L.

1992-03-01

This report describes the development and testing of a deuterium gas target intended for use at a low-energy accelerator facility to produce neutrons for basic research and various nuclear applications. The principle source reaction is H-2(d,n)He-3. It produces a nearly mono-energetic group of neutrons. However, a lower-energy continuum neutron spectrum is produced by the H-2(d;n,p)H-2 reaction and also by deuterons which strike various components in the target assembly. The present target is designed to achieve the following objectives: (1) minimize unwanted background neutron production from the target assembly, (2) provide a relatively low level of residual long-term activity within the target components, (3) have the capacity to dissipate up to 150 watts of beam power with good target longevity, and (4) possess a relatively modest target mass in order to minimize neutron scattering from the target components. The basic physical principles that have to be considered in designing an accelerator target are discussed and the major engineering features of this particular target design are outlined. The results of initial performance tests on this target are documented and some conclusions concerning the viability of the target design are presented

Tritium target manufacturing for use in accelerators

Science.gov (United States)

Bach, P.; Monnin, C.; Van Rompay, M.; Ballanger, A.

2001-07-01

As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium target on copper substrate, and going to more sophisticated devices. A wide range of possible uses is covered, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets for higher lifetimes, or large size rotating targets for accelerators used in boron neutron therapy. Activity of targets lies in the 1 to 1000 Curie, diameter of targets being up to 30 cm. Special targets are also considered, including surface layer targets for lowering tritium desorption under irradiation, or those made from different kinds of occluders such as titanium, zirconium, erbium, scandium, with different substrates. It is then possible to optimize either neutron output, or lifetime and stability, or thermal behavior.

Deuterium and big bang nucleosynthesis

International Nuclear Information System (INIS)

Burles, S.

2000-01-01

Measurements of deuterium absorption in high redshift quasar absorption systems provide a direct inference of the deuterium abundance produced by big bang nucleosynthesis (BBN). With measurements and limits from five independent absorption systems, we place strong constraints on the primordial ratio of deuterium to hydrogen, (D/H) p = 3.4 ± 0.3 x 10 -5 [1,2]. We employ a direct numerical treatment to improve the estimates of critical reaction rates and reduce the uncertainties in BBN predictions of D/H and 7 Li/H by a factor of three[3] over previous efforts[4]. Using our measurements of (D/H) p and new BBN predictions, we find at 95% confidence the baryon density ρ b = (3.6 ± 0.4) x 10 -31 g cm -3 (Ω b h 2 65 = 0.045 ± 0.006 in units of the critical density), and cosmological baryon-photon ratio η = (5.1 ± 0.6) x 10 -10

Permeation of deuterium implanted into vanadium alloys

International Nuclear Information System (INIS)

Anderl, R.A.; Longhurst, G.R.; Struttmann, D.A.

1986-05-01

Permeation of deuterium through the vanadium alloy, V-15Cr-5Ti, was investigated using 3-keV, D 3 + ion beams from a small accelerator. The experiments consisted of measurements of the deuterium reemission and permeation rates as a function of implantation fluence for 0.5-mm thick specimens heated to tempertures from 623 to 823 0 K. Implantation-side surface characterization was made by simultaneous measurements of sputtered ions with a secondary ion mass spectrometer (SIMS). Analyses of these measurements indicate that for the experimental conditions used, the steady-state deuterium permeation flux in V-15Cr-5Ti is approximately 18% of the implantation flux. This corresponds to approximately 1000 times that seen in the ferritic steel, HT-9, under comparable conditions. Measurement of deuterium diffusivity in V-15Cr-5Ti using permeation break-through times indicates D = 1.4 x 10 -8 exp(-.11 eV/kT) (m 2 /s)

Energy Levels of Hydrogen and Deuterium

Science.gov (United States)

SRD 142 NIST Energy Levels of Hydrogen and Deuterium (Web, free access)   This database provides theoretical values of energy levels of hydrogen and deuterium for principle quantum numbers n = 1 to 200 and all allowed orbital angular momenta l and total angular momenta j. The values are based on current knowledge of the revelant theoretical contributions including relativistic, quantum electrodynamic, recoil, and nuclear size effects.

Site occupation state of deuterium atoms in fcc Fe

International Nuclear Information System (INIS)

Aoki, Katsutoshi; Machida, Akihiko; Saitoh, Hiroyuki; Hattori, Takanori; Sano-Furukawa, Asami

2015-01-01

The deuterization process of fcc Fe to form solid-solution fcc FeD x was investigated by in situ neutron diffraction measurements at high temperature and high pressure. In a completely deuterized specimen at 988 K and 6.3 GPa, deuterium atoms occupy the octahedral and tetrahedral interstitial sites with an occupancy of 0.532(9) and 0.056(5), respectively, giving a deuterium composition x of 0.64(1). During deuterization, the metal-lattice expands approximately linearly with deuterium composition at a rate of 2.21 Å 3 per deuterium atom. The minor occupation of tetrahedral site is likely driven by the intersite movement of deuterium atoms along the <111> direction in the fcc metal lattice. These results provide implications for the light elements in the Earth's core and the mechanism of hydrogen embrittlement of ferrous metals. (author)

Deuterium retention and desorption behavior in an advanced reduced-activation alloy

Energy Technology Data Exchange (ETDEWEB)

Noh, S.J., E-mail: sjnoh@dankook.ac.kr [Department of Applied Physics, Dankook University, Yongin-si, Gyeonggi-do 448-701 (Korea, Republic of); Kim, H.S.; Byeon, W.J.; Shin, H.W. [Department of Applied Physics, Dankook University, Yongin-si, Gyeonggi-do 448-701 (Korea, Republic of); Lee, Cheol Eui [Department of Physics, Korea University, Seoul 136-713 (Korea, Republic of); Lee, S.K. [Nuclear Fusion Development Division, Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseong-gu, Daejeon 305-353 (Korea, Republic of)

2017-07-15

We present the first experimental results of the deuterium retention and desorption behavior in an advanced reduced-activation alloy (ARAA) under development in Korea. For the in-situ measurement of desorbed gases from samples immediately after irradiation, a thermal desorption spectroscopy (TDS) system clustered with an inductively coupled plasma ion source has been built. Samples were and were not irradiated with helium ions at energies of 1.4, 3.5, and 5.0 keV and then continuously irradiated with 1.7-keV deuterium ions. TDS measurements were performed in situ immediately after deuterium irradiation and after exposure to air for one week. The amount of desorbed deuterium is the largest for the sample without helium irradiation from the TDS results measured in situ immediately after irradiation. Further, the amount of desorbed deuterium is significantly lowered when the helium energy is increased to 3.5 keV with no significant changes thereafter, indicating that the layer formed by implanted helium at near or deeper than the stopping range for 1.7-keV deuterium ions effectively acts as a barrier against deuterium diffusion into the depth. Because of the strong diffusivity of deuterium into the ambient atmosphere, the amounts of desorbed deuterium are greatly reduced for the samples without helium irradiation and with 1.4-keV helium irradiation after exposure to air for one week. In addition, our deuterium results for the ARAA are also compared with the results for F82H by other authors. - Highlights: •The first result of the deuterium retention and desorption in an ARAA is presented. •The ARAA was irradiated with helium and then continuously irradiated with deuterium. •TDS measurements were performed in situ immediately after deuterium irradiation. •TDS measurements were performed after exposure to air for one week. •The effects of helium irradiation and exposure to air were investigated.

ICRF heating and transport of deuterium-tritium plasmas in TFTR

International Nuclear Information System (INIS)

Murakami, M.; Batchelor, D.B.; Bush, C.E.

1994-01-01

This paper describes results of the first experiments utilizing high-power ion cyclotron range of frequency (ICRF) to heat deuterium-tritium (D-T) plasmas in reactor-relevant regimes on the Tokamak Fusion Test Reactor (TFTR). Results from these experiments have demonstrated efficient core, second harmonic, tritium heating of D-T supershot plasmas with tritium concentrations ranging from 6%--40%. Significant direct ion heating on the order of 60% of the input radio frequency (rf) power has been observed. The measured deposition profiles are in good agreement with two-dimensional modeling code predictions. Confinement in an rf-heated supershot is at least similar to that without rf, and possibly better in the electron channel. Efficient electron heating via mode conversion of fast waves to ion Bernstein waves (IBW) has been demonstrated in ohmic, deuterium-deuterium and DT-neutral beam injection plasmas with high concentrations of minority 3 He (n 3 He /n e > 10%). By changing the 3 He concentration or the toroidal field strength, the location of the mode-conversion radius was varied. The power deposition profile measured with rf power modulation showed that up to 70% of the power can be deposited on electrons at an off-axis position. Preliminary results with up to 4 MW coupled into the plasma by 90-degree phased antennas showed directional propagation of the mode-converted IBW. Heat wave propagation showed no strong inward thermal pinch in off-axis heating of an ohmically-heated (OH) target plasma in TFIR

Submolecular regulation of cell transformation by deuterium depleting water exchange reactions in the tricarboxylic acid substrate cycle.

Science.gov (United States)

Boros, László G; D'Agostino, Dominic P; Katz, Howard E; Roth, Justine P; Meuillet, Emmanuelle J; Somlyai, Gábor

2016-02-01

The naturally occurring isotope of hydrogen ((1)H), deuterium ((2)H), could have an important biological role. Deuterium depleted water delays tumor progression in mice, dogs, cats and humans. Hydratase enzymes of the tricarboxylic acid (TCA) cycle control cell growth and deplete deuterium from redox cofactors, fatty acids and DNA, which undergo hydride ion and hydrogen atom transfer reactions. A model is proposed that emphasizes the terminal complex of mitochondrial electron transport chain reducing molecular oxygen to deuterium depleted water (DDW); this affects gluconeogenesis as well as fatty acid oxidation. In the former, the DDW is thought to diminish the deuteration of sugar-phosphates in the DNA backbone, helping to preserve stability of hydrogen bond networks, possibly protecting against aneuploidy and resisting strand breaks, occurring upon exposure to radiation and certain anticancer chemotherapeutics. DDW is proposed here to link cancer prevention and treatment using natural ketogenic diets, low deuterium drinking water, as well as DDW production as the mitochondrial downstream mechanism of targeted anti-cancer drugs such as Avastin and Glivec. The role of (2)H in biology is a potential missing link to the elusive cancer puzzle seemingly correlated with cancer epidemiology in western populations as a result of excessive (2)H loading from processed carbohydrate intake in place of natural fat consumption. Published by Elsevier Ltd.

Radiation assisted thermonuclear burn wave dynamics in heavy ion fast ignition of cylindrical deuterium-tritium fuel target

International Nuclear Information System (INIS)

Rehman, S.; Kouser, R.; Nazir, R.; Manzoor, Z.; Tasneem, G.; Jehan, N.; Nasim, M.H.; Salahuddin, M.

2015-01-01

Dynamics of thermonuclear burn wave propagation assisted by thermal radiation precursor in a heavy ion fast ignition of cylindrical deuterium-tritium (DT) fuel target are studied by two dimensional radiation hydrodynamic simulations using Multi-2D code. Thermal radiations, as they propagate ahead of the burn wave, suffer multiple reflections and preheat the fuel, are found to play a vital role in burn wave dynamics. After fuel ignition, the burn wave propagates in a steady state manner for some time. Multiple reflection and absorption of radiation at the fuel-tamper interface, fuel ablation and radial implosion driven by ablative shock and fast fusion rates on the fuel axis, at relatively later times, result into filamentary wave front. Strong pressure gradients are developed and sausage like structures behind the front are appeared. The situation leads to relatively reduced and non-uniform radial fuel burning and burn wave propagation. The fuel burning due to DD reaction is also taken into account and overall fusion energy and fusion power density, due to DT and DD reactions, during the burn wave propagation are determined as a function of time. (authors)

Affinity capture of biotinylated proteins at acidic conditions to facilitate hydrogen/deuterium exchange mass spectrometry analysis of multimeric protein complexes

DEFF Research Database (Denmark)

Jensen, Pernille Foged; Jørgensen, Thomas J. D.; Koefoed, Klaus

2013-01-01

Characterization of conformational and dynamic changes associated with protein interactions can be done by hydrogen/deuterium exchange mass spectrometry (HDX-MS) by comparing the deuterium uptake in the bound and unbound state of the proteins. Investigation of local hydrogen/deuterium exchange...... in heteromultimeric protein complexes poses a challenge for the method due to the increased complexity of the mixture of peptides originating from all interaction partners in the complex. Previously, interference of peptides from one interaction partner has been removed by immobilizing the intact protein on beads...... complexes without interference of peptides originating from other interaction partners in the complex. The biotin-streptavidin strategy has been successfully implemented in a model system with two recombinant monoclonal antibodies that target nonoverlapping epitopes on the human epidermal growth factor...

Characterisation of deuterium spectra from laser driven multi-species sources by employing differentially filtered image plate detectors in Thomson spectrometers

International Nuclear Information System (INIS)

Alejo, A.; Kar, S.; Ahmed, H.; Doria, D.; Green, A.; Jung, D.; Lewis, C. L. S.; Nersisyan, G.; Krygier, A. G.; Freeman, R. R.; Clarke, R.; Green, J. S.; Notley, M.; Fernandez, J.; Fuchs, J.; Kleinschmidt, A.; Roth, M.; Morrison, J. T.; Najmudin, Z.; Nakamura, H.

2014-01-01

A novel method for characterising the full spectrum of deuteron ions emitted by laser driven multi-species ion sources is discussed. The procedure is based on using differential filtering over the detector of a Thompson parabola ion spectrometer, which enables discrimination of deuterium ions from heavier ion species with the same charge-to-mass ratio (such as C 6+ , O 8+ , etc.). Commonly used Fuji Image plates were used as detectors in the spectrometer, whose absolute response to deuterium ions over a wide range of energies was calibrated by using slotted CR-39 nuclear track detectors. A typical deuterium ion spectrum diagnosed in a recent experimental campaign is presented, which was produced from a thin deuterated plastic foil target irradiated by a high power laser

Characterisation of deuterium spectra from laser driven multi-species sources by employing differentially filtered image plate detectors in Thomson spectrometers

Science.gov (United States)

Alejo, A.; Kar, S.; Ahmed, H.; Krygier, A. G.; Doria, D.; Clarke, R.; Fernandez, J.; Freeman, R. R.; Fuchs, J.; Green, A.; Green, J. S.; Jung, D.; Kleinschmidt, A.; Lewis, C. L. S.; Morrison, J. T.; Najmudin, Z.; Nakamura, H.; Nersisyan, G.; Norreys, P.; Notley, M.; Oliver, M.; Roth, M.; Ruiz, J. A.; Vassura, L.; Zepf, M.; Borghesi, M.

2014-09-01

A novel method for characterising the full spectrum of deuteron ions emitted by laser driven multi-species ion sources is discussed. The procedure is based on using differential filtering over the detector of a Thompson parabola ion spectrometer, which enables discrimination of deuterium ions from heavier ion species with the same charge-to-mass ratio (such as C6 +, O8 +, etc.). Commonly used Fuji Image plates were used as detectors in the spectrometer, whose absolute response to deuterium ions over a wide range of energies was calibrated by using slotted CR-39 nuclear track detectors. A typical deuterium ion spectrum diagnosed in a recent experimental campaign is presented, which was produced from a thin deuterated plastic foil target irradiated by a high power laser.

Characterisation of deuterium spectra from laser driven multi-species sources by employing differentially filtered image plate detectors in Thomson spectrometers

Energy Technology Data Exchange (ETDEWEB)

Alejo, A.; Kar, S., E-mail: s.kar@qub.ac.uk; Ahmed, H.; Doria, D.; Green, A.; Jung, D.; Lewis, C. L. S.; Nersisyan, G. [Centre for Plasma Physics, School of Mathematics and Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Krygier, A. G.; Freeman, R. R. [Department of Physics, The Ohio State University, Columbus, Ohio 43210 (United States); Clarke, R.; Green, J. S.; Notley, M. [Central Laser Facility, Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Fernandez, J. [Central Laser Facility, Rutherford Appleton Laboratory, Didcot, Oxfordshire OX11 0QX (United Kingdom); Instituto de Fusión Nuclear, Universidad Politécnica de Madrid, 28006 Madrid (Spain); Fuchs, J. [LULI, École Polytechnique, CNRS, CEA, UPMC, 91128 Palaiseau (France); Kleinschmidt, A.; Roth, M. [Institut für Kernphysik, Technische Universität Darmstadt, Schloßgartenstrasse 9, D-64289 Darmstadt (Germany); Morrison, J. T. [Propulsion Systems Directorate, Air Force Research Lab, Wright Patterson Air Force Base, Ohio 45433 (United States); Najmudin, Z.; Nakamura, H. [Blackett Laboratory, Department of Physics, Imperial College, London SW7 2AZ (United Kingdom); and others

2014-09-15

A novel method for characterising the full spectrum of deuteron ions emitted by laser driven multi-species ion sources is discussed. The procedure is based on using differential filtering over the detector of a Thompson parabola ion spectrometer, which enables discrimination of deuterium ions from heavier ion species with the same charge-to-mass ratio (such as C{sup 6+}, O{sup 8+}, etc.). Commonly used Fuji Image plates were used as detectors in the spectrometer, whose absolute response to deuterium ions over a wide range of energies was calibrated by using slotted CR-39 nuclear track detectors. A typical deuterium ion spectrum diagnosed in a recent experimental campaign is presented, which was produced from a thin deuterated plastic foil target irradiated by a high power laser.

First-principles thermal conductivity of warm-dense deuterium plasmas for inertial confinement fusion applications.

Science.gov (United States)

Hu, S X; Collins, L A; Boehly, T R; Kress, J D; Goncharov, V N; Skupsky, S

2014-04-01

Thermal conductivity (κ) of both the ablator materials and deuterium-tritium (DT) fuel plays an important role in understanding and designing inertial confinement fusion (ICF) implosions. The extensively used Spitzer model for thermal conduction in ideal plasmas breaks down for high-density, low-temperature shells that are compressed by shocks and spherical convergence in imploding targets. A variety of thermal-conductivity models have been proposed for ICF hydrodynamic simulations of such coupled and degenerate plasmas. The accuracy of these κ models for DT plasmas has recently been tested against first-principles calculations using the quantum molecular-dynamics (QMD) method; although mainly for high densities (ρ > 100 g/cm3), large discrepancies in κ have been identified for the peak-compression conditions in ICF. To cover the wide range of density-temperature conditions undergone by ICF imploding fuel shells, we have performed QMD calculations of κ for a variety of deuterium densities of ρ = 1.0 to 673.518 g/cm3, at temperatures varying from T = 5 × 103 K to T = 8 × 106 K. The resulting κQMD of deuterium is fitted with a polynomial function of the coupling and degeneracy parameters Γ and θ, which can then be used in hydrodynamic simulation codes. Compared with the "hybrid" Spitzer-Lee-More model currently adopted in our hydrocode lilac, the hydrosimulations using the fitted κQMD have shown up to ∼20% variations in predicting target performance for different ICF implosions on OMEGA and direct-drive-ignition designs for the National Ignition Facility (NIF). The lower the adiabat of an imploding shell, the more variations in predicting target performance using κQMD. Moreover, the use of κQMD also modifies the shock conditions and the density-temperature profiles of the imploding shell at early implosion stage, which predominantly affects the final target performance. This is in contrast to the previous speculation that κQMD changes mainly the

Peculiarities of using mixed deuterium and tritium ion beams of complicated atomic-molecular composition for fast neutron generation

International Nuclear Information System (INIS)

Kir'yanov, G.I.; Syromukov, S.V.

1983-01-01

The neutron yield is calculated depending on deuterium and tritium beam parameters as well as on the target parameters. Cases of target presaturation with hydrogen nuclides and of target stuffing with the ion beam in the process of the system functioning are discussed. It is shown that the neutron yield is approximately three times more in the case with a pure beam compared to the case with a niked beam

Electron scattering from high-momentum neutrons in deuterium

International Nuclear Information System (INIS)

Klimenko, A.V.; Kuhn, S.E.; Bueltmann, S.; Careccia, S.L.; Dharmawardane, K.V.; Dodge, G.E.; Guler, N.; Hyde-Wright, C.E.; Klein, A.; Tkachenko, S.; Weinstein, L.B.; Zhang, J.; Butuceanu, C.; Griffioen, K.A.; Baillie, N.; Fersch, R.G.; Funsten, H.; Egiyan, K.S.; Asryan, G.; Dashyan, N.B.

2006-01-01

We report results from an experiment measuring the semiinclusive reaction 2 H(e,e ' p s ) in which the proton p s is moving at a large angle relative to the momentum transfer. If we assume that the proton was a spectator to the reaction taking place on the neutron in deuterium, the initial state of that neutron can be inferred. This method, known as spectator tagging, can be used to study electron scattering from high-momentum (off-shell) neutrons in deuterium. The data were taken with a 5.765 GeV electron beam on a deuterium target in Jefferson Laboratory's Hall B, using the CEBAF large acceptance spectrometer. A reduced cross section was extracted for different values of final state missing mass W*, backward proton momentum p → s , and momentum transfer Q 2 . The data are compared to a simple plane wave impulse approximation (PWIA) spectator model. A strong enhancement in the data observed at transverse kinematics is not reproduced by the PWIA model. This enhancement can likely be associated with the contribution of final state interactions (FSI) that were not incorporated into the model. Within the framework of the simple spectator model, a 'bound neutron structure function' F 2n eff was extracted as a function of W* and the scaling variable x* at extreme backward kinematics, where the effects of FSI appear to be smaller. For p s >0.4 GeV/c, where the neutron is far off-shell, the model overestimates the value of F 2n eff in the region of x* between 0.25 and 0.6. A dependence of the bound neutron structure function on the neutron's 'off-shell-ness' is one possible effect that can cause the observed deviation

Implanted Deuterium Retention and Release in Carbon-Coated Beryllium

Science.gov (United States)

Anderl, R. A.; Longhurst, G. R.; Pawelko, R. J.; Oates, M. A.

1997-06-01

Deuterium implantation experiments have been conducted on samples of clean and carbon-coated beryllium. These studies entailed preparation and characterization of beryllium samples coated with carbon thicknesses of 100, 500, and 1000 Å. Heat treatment of a beryllium sample coated with carbon to a thickness of approximately 100 Å revealed that exposure to a temperature of 400°C under high vacuum conditions was sufficient to cause substantial diffusion of beryllium through the carbon layer, resulting in more beryllium than carbon at the surface. Comparable concentrations of carbon and beryllium were observed in the bulk of the coating layer. Higher than expected oxygen levels were observed throughout the coating layer as well. Samples were exposed to deuterium implantation followed by thermal desorption without exposure to air. Differences were observed in deuterium retention and postimplantation release behavior in the carbon-coated samples as compared with bare samples. For comparable implantation conditions (sample temperature of 400°C and an incident deuterium flux of approximately 6 × 1019 D/m2-s), the quantity of deuterium retained in the bare sample was less than that retained in the carbon-coated samples. Further, the release of the deuterium took place at lower temperatures for the bare beryllium surfaces than for carbon-coated beryllium samples.

Cosmic Deuterium and Social Networking Software

Science.gov (United States)

Pasachoff, J. M.; Suer, T.-A.; Lubowich, D. A.; Glaisyer, T.

2006-08-01

For the education of newcomers to a scientific field and for the convenience of students and workers in the field, it is helpful to have all the basic scientific papers gathered. For the study of deuterium in the Universe, in 2004-5 we set up http://www.cosmicdeuterium.info with clickable links to all the historic and basic papers in the field and to many of the current papers. Cosmic deuterium is especially important because all deuterium in the Universe was formed in the epoch of nucleosynthesis in the first 1000 seconds after the Big Bang, so study of its relative abundance (D:H~1:100,000) gives us information about those first minutes of the Universe's life. Thus the understanding of cosmic deuterium is one of the pillars of modern cosmology, joining the cosmic expansion, the 3 degree cosmic background radiation, and the ripples in that background radiation. Studies of deuterium are also important for understanding Galactic chemical evolution, astrochemistry, interstellar processes, and planetary formation. Some papers had to be scanned while others are available at the Astrophysical Data System, adswww.harvard.edu, or to publishers' Websites. By 2006, social networking software (http:tinyurl.com/ zx5hk) had advanced with popular sites like facebook.com and MySpace.com; the Astrophysical Data System had even set up MyADS. Social tagging software sites like http://del.icio.us have made it easy to share sets of links to papers already available online. We have set up http://del.icio.us/deuterium to provide links to many of the papers on cosmicdeuterium.info, furthering previous del.icio.us work on /eclipses and /plutocharon. It is easy for the site owner to add links to a del.icio.us site; it takes merely clicking on a button on the browser screen once the site is opened and the desired link is viewed in a browser. Categorizing different topics by keywords allows subsets to be easily displayed. The opportunity to expose knowledge and build an ecosystem of web

Carbon and deuterium nuclear magnetic resonance in solids

Energy Technology Data Exchange (ETDEWEB)

Shattuck, Thomas Wayne [Univ. of California, Berkeley, CA (United States)

1976-07-01

In Chapter I we present the results on a study of cross polarization dynamics, between protons and carbon-13 in adamantane, by the direct observation of the dilute, carbon-13, spins. These dynamics are an important consideration in the efficiency of proton enhancement double-resonance techniques and they also provide good experimental models for statistical theories of cross relaxation. In order to test these theories we present a comparison of the experimental and theoretical proton dipolar fluctuation correlation time τ_c, which is experimentally 110 ± 15 μsec and theoretically 122 μsec for adamantane. These double resonance considerations provide the background for extensions to deuterium and double quantum effects discussed in Chapter II. In Chapter II an approach to high resolution nmr of deuterium in solids is described. The m = 1 → -1 transition is excited by a double quantum process and the decay of coherence Q(τ) is monitored. Fourier transformation yields a deuterium spectrum devoid of quadrupole splittings and broadening. If the deuterium nuclei are dilute and the protons are spin decoupled, the double-quantum spectrum is a high resolution one and yields information on the deuterium chemical shifts Δω. The relationship Q(τ) ~ cos 2Δωτ is checked and the technique is applied to a single crystal of oxalic acid dihydrate enriched to ~ 10% in deuterium. The carboxyl and the water deuterium shifts are indeed resolved and the anisotropy of the carboxyl shielding tensor is estimated to be Δσ = 32 ± 3 ppm. A complete theoretical analysis is presented. The extension of cross relaxation techniques, both direct and indirect, to proton-deuterium double resonance is also described. The m = 1 → -1 double quantum transition and the m = ± 1 → 0 single quantum transitions may all be polarized and we present the derivation of the Hartmann-Hahn cross polarization conditions for each case. In addition the dynamics of the double quantum process

Sputtering of solid deuterium by He-ions

DEFF Research Database (Denmark)

Schou, Jørgen; Stenum, B.; Pedrys, R.

2001-01-01

Sputtering of solid deuterium by bombardment of 3He+ and 4He+ ions was studied. Some features are similar to hydrogen ion bombardment of solid deuterium, but for the He-ions a significant contribution of elastic processes to the total yield can be identified. The thin-film enhancement is more pro...... pronounced than that for hydrogen projectiles in the same energy range....

Process for the production of high purity deuterium

International Nuclear Information System (INIS)

Arrathoon, R.

1977-01-01

A process for the electrolysis of heavy water which results in the production of high purity deuterium without periodic replenishment of the electrolyte with additional deuterated compounds is defined. Electrolysis is effected through the use of an inexpensive cation-action permselective membrane which is essentially a solid polymer electrolyte and which is capable of automatically separating the evolved deuterium and oxygen gas. This cation-active permselective membrane does not introduce any intrinsic impurities or tritium contamination in the generated deuterium gas, does not require periodic revitalization with deuterated compounds or other chemical compounds, and is characterized by an unusually high electrical efficiency

Deuterium NMR, induced and intrinsic cholesteric lyomesophases

International Nuclear Information System (INIS)

Alcantara, M.R.

1982-01-01

Induced and intrinsic cholesteric lyotropic mesophases were studied. Induced cholesteric lyomesophases based on potassium laurate (KL) system, with small amounts of cholesterol added, were studied by deuterium NMR and by polarizing microscopy. Order profiles obtained from deuterium NMR of KL perdenderated chains in both induced cholesteric and normal mesophases were compared. The intrinsic cholesteric lyotropic mesophases were based on the amphiphile potassium N-lauroyl serinate (KLNS) in the resolved levo form. The study of the type I intrinsic cholesteric mesophase was made by optical microscopy under polarized light and the type II intrinsic cholesteric lyomesophase was characterized by deuterium NMR. The new texture was explained by the use of the theory of disclinations developed for thermotropic liquid crystals, specially for cholesteric type. (M.J.C.) [pt

Chemical behavior of energetic deuterium implanted into silicon carbide

International Nuclear Information System (INIS)

Iguchi, Kazunari; Morimoto, Yasutomi; Shimada, Asako; Inuduka, Nobuo; Okuno, Kenji; Nakamura, Hirohumi; Nishi, Masataka

2000-01-01

Studies on chemical behavior of energetic deuterium (D) ions implanted into SiC were carried out by means of X-ray Photoelectron Spectroscopy (XPS) and Thermal Desorption Spectroscopy (TDS). From XPS results, it was suggested that the implanted D was attracted strongly to Si and/or C. From TDS results, two peaks corresponding to D 2 release appeared near 470 K (1st peak) and 1080 K (2nd peak). The activation energies for the two D 2 release processes were also determined. It was found from these experimental results that the 1st peak seemed to be attributed to deuterium that existed in interstitial. The 2nd peak was considered to be caused by deuterium trapped in lattice defects produced through deuterium ion implantation. (author)

Thermodynamic and electrical properties of laser-shocked liquid deuterium

Science.gov (United States)

He, Zhiyu; Jia, Guo; Zhang, Fan; Luo, Kui; Huang, Xiuguang; Shu, Hua; Fang, Zhiheng; Ye, Junjian; Xie, Zhiyong; Xia, Miao; Fu, Sizu

2018-01-01

Liquid deuterium at high pressure and temperature has been observed to undergo significant electronic structural changes. Reflectivity and temperature measurements of liquid deuterium up to around 70 GPa were obtained using a quartz standard. The observed specific heat of liquid deuterium approaches the Dulong-Petit limit above 1 eV. Discussions on specific heat indicate a molecular dissociation below 1 eV and fully dissociated above 1.5 eV. Also, the electrical conductivity of deuterium estimated from reflectivity reaches 1.3 × 105 (Ωṡm)-1, proving that deuterium in this condition is a conducting degenerate liquid metal and undergo an insulator-metal transition. The results from specific heat, carrier density and conductivity agreed well with each other, which might be a reinforcement of the insulator-metal transition and the molecular dissociation. In addition, a new correction method of reflectivity in temperature calculation was proposed to improve the accuracy of temperature results. A new "dynamic calibration" was introduced in this work to make the experiments simpler and more accurate.

ICRF heating and transport of deuterium-tritium plasmas in TFTR

International Nuclear Information System (INIS)

Rogers, J.H.; Schilling, G.; Stevens, J.E.; Taylor, G.; Wilson, J.R.; Bell, M.G.; Budny, R.V.; Bretz, N.L.; Darrow, D.; Fredrickson, E.

1995-02-01

This paper describes results of the first experiments utilizing high-power ion cyclotron range of frequency (ICRF) to heat deuterium-tritium (D-T) plasmas in reactor-relevant regimes on the Tokamak Fusion Test Reactor (TFTR). Results from these experiments have demonstrated efficient core, second harmonic, tritium beating of D-T supershot plasmas with tritium concentrations ranging from 6%-40%. Significant direct ion heating on the order of 60% of the input radio frequency (rf) power has been observed. The measured deposition profiles are in good agreement with two-dimensional modeling code predictions. Energy confinement in an rf-heated supershot is at least similar to that without rf, and possibly better in the electron channel. Efficient electron heating via mode conversion of fast waves to ion Bernstein waves (IBW) has been demonstrated in ohmic, deuterium-deuterium and DT-neutral beam injection plasmas with high concentrations of minority 3 He (n 3He /n e = 15% - 30%). By changing the 3 He concentration or the toroidal field strength, the location of the mode-conversion radius was varied. The power deposition profile measured with rf power modulation indicated that up to 70% of the power can be deposited on electrons at an off-axis position. Preliminary results with up to 4 MW coupled into the plasma by 90-degree phased antennas showed directional propagation of the mode-converted IBW. Analysis of heat wave propagation showed no strong inward thermal pinch in off-axis heating of an ohmically-heated target plasma in TFTR

Deuterium in New Zealand rivers and streams

International Nuclear Information System (INIS)

Stewart, M.K.; Cox, M.A.; James, M.R.; Lyon, G.

1983-07-01

Over 750 deuterium measurements on rivers and streams in New Zealand are reported. Monthly samples were collected for periods of several years from a number of representative rivers. These show irregular storm-to-storm as well as seasonal deuterium variations. The seasonal variations range from as low as 1 per mille for lake-fed rivers to 8-10 per mille for rivers with large spring snow-melt contributions. Variations in mean annual ΔD values are believed to reflect changes in climatic variables; the present data will be used to compare with future changes. The bulk of the data are single samples; these show a geographic variation related to the altitude, latitude and climatic character of the catchments, with the highest deuterium contents (ΔD = -20 per mille) occurring in the far north, and lowest contents (-80 per mille) in the inland Otago region. Regression equations derived for the ΔD dependence on altitude (h) and latitude (l), are ΔD = -0.0169 h - 30.2 and westerly influence. Eastern climatic zones have lower deuterium contents because of rainout effects on the axial ranges. Contours of constant

Deuterium gas-driven permeation and subsequent retention in rolled tungsten foils

International Nuclear Information System (INIS)

Liu, Feng; Zhou, Haishan; Li, Xiao-Chun; Xu, Yuping; An, Zhongqing; Mao, Hongmin; Xing, Wenjing; Hou, Qing; Luo, Guang-Nan

2014-01-01

Experiments concerning deuterium gas-driven permeation through rolled tungsten foils in the temperature range of 850–950 K and subsequent deuterium retention have been performed. The steady state permeation flux of deuterium is proportional to the square root of the driving pressure. The permeability of deuterium is in an order of 10 −14 mol m −1 s −1 Pa −1/2 in this temperature range and the activation energy for permeation is 1.21 eV. Measurements of diffusivity are significantly affected by the driving pressure, which can be well explained by a saturable-trap model. Thermal desorption spectra of samples feature a single deuterium release peak at about 873 K. TMAP 4 modeling of this peak gives a detrapping energy of 1.70 eV, which fits the dissociation enthalpy of deuterium desorbing from the inner wall of vacancy clusters or pores in tungsten

Deuterium gas-driven permeation and subsequent retention in rolled tungsten foils

Science.gov (United States)

Liu, Feng; Zhou, Haishan; Li, Xiao-Chun; Xu, Yuping; An, Zhongqing; Mao, Hongmin; Xing, Wenjing; Hou, Qing; Luo, Guang-Nan

2014-12-01

Experiments concerning deuterium gas-driven permeation through rolled tungsten foils in the temperature range of 850-950 K and subsequent deuterium retention have been performed. The steady state permeation flux of deuterium is proportional to the square root of the driving pressure. The permeability of deuterium is in an order of 10-14 mol m-1 s-1 Pa-1/2 in this temperature range and the activation energy for permeation is 1.21 eV. Measurements of diffusivity are significantly affected by the driving pressure, which can be well explained by a saturable-trap model. Thermal desorption spectra of samples feature a single deuterium release peak at about 873 K. TMAP 4 modeling of this peak gives a detrapping energy of 1.70 eV, which fits the dissociation enthalpy of deuterium desorbing from the inner wall of vacancy clusters or pores in tungsten.

Phenomenological nuclear reaction description in deuterium-saturated palladium and synthesized structure in dense deuterium gas under γ-quanta irradiation

International Nuclear Information System (INIS)

Didyk, A.Yu.; Wisniewski, R.

2012-01-01

The observed phenomena on the changes of chemical compositions in our previous reports allowed us to develop a phenomenological nuclear fusion-fission model with taking into consideration the elastic and inelastic scattering of photoprotons and photoneutrons, heating of surrounding deuterium nuclei, following D-D fusion reactions and fission of middle-mass nuclei by 'hot' protons, deuterons and various-energy neutrons. Such chain processes could produce the necessary number of neutrons, 'hot' deuterons for explanation of the observed experimental results. The developed approach can be a basis for creation of deuterated nuclear fission reactors (DNFR) with high-density deuterium gas and so-called deuterated metals. Also, the developed approach can be used for the study of nuclear reactions in high-density deuterium or tritium gases and deuterated metals

Some methods for labelling organic compounds by deuterium

International Nuclear Information System (INIS)

Moustapha, C.

1988-01-01

The rapid growth of knowledge in the fields of biochemistry, physiology, and molecular biology reflects to a considerable degree the utilization of stable isotopes (specially deuterium) in the study of chemical reactions and fragmentation mechanisms in mass spectrometry, as well as in the pharmacological and biological studies. Organic compounds maybe labelled by deuterium through classic organic reactions by using special deuterated solvents and reagents. This article discusses some reactions, with examples on how to prepare labelled compounds with high isotopic purety. These reactions are: exchange reactions in acid and alkaline media (the exchange in the chromatographic column in liquid and gas phases, the exchange in homogenous medium), reduction reactions of functional groups as well as saturation of the double bounds by deuterium using hydrogenation catalystes, electrochemical reactions using KOLBE, and photochemical reactions. This article also deals with spectroscopic properties of deuterium and the methods which are used to identify its compounds such as infrared, nuclear magnetic resonance, and mass spectroscopy. 37 refs., 2 figs

Implanted deuterium retention and release in carbon-coated beryllium

International Nuclear Information System (INIS)

Anderl, R.A.; Longhurst, G.R.; Pawelko, R.J.; Oates, M.A.

1997-01-01

Deuterium implantation experiments have been conducted on samples of clean and carbon-coated beryllium. These studies entailed preparation and characterization of beryllium samples coated with carbon thicknesses of 100, 500, and 1000 angstrom. Heat treatment of a beryllium sample coated with carbon to a thickness of approximately 100 angstrom revealed that exposure to a temperature of 400 degrees C under high vacuum conditions was sufficient to cause substantial diffusion of beryllium through the carbon layer, resulting in more beryllium than carbon at the surface. Comparable concentrations of carbon and beryllium were observed in the bulk of the coating layer. Higher than expected oxygen levels were observed throughout the coating layer as well. Samples were exposed to deuterium implantation followed by thermal desorption without exposure to air. Differences were observed in deuterium retention and postimplantation release behavior in the carbon-coated samples as compared with bare samples. For comparable implantation conditions (sample temperature of 400 degrees C and an incident deuterium flux of approximately 6 X 10 19 D/m 2 sec), the quantity of deuterium retained in the bare sample was less than that retained in the carbon-coated samples. Further, the release of the deuterium took place at lower temperatures for the bare beryllium surfaces than for carbon-coated beryllium samples. 4 refs., 8 figs., 1 tab

Deuterium exchange between liquid water and gaseous hydrogen

International Nuclear Information System (INIS)

Dave, S.M.; Ghosh, S.K.; Sadhukhan, H.K.

1982-01-01

The overall separation factors for the deuterium exchange between liquid water and gaseous hydrogen have been calculated over a wide range of temperature, pressure and deuterium concentrations. These data would be useful in the design and other considerations for heavy water production, based on hydrogen-water exchange. (author)

Measuring the hydrogen/deuterium exchange of proteins at high spatial resolution by mass spectrometry: overcoming gas-phase hydrogen/deuterium scrambling.

Science.gov (United States)

Rand, Kasper D; Zehl, Martin; Jørgensen, Thomas J D

2014-10-21

Proteins are dynamic molecules that exhibit conformational flexibility to function properly. Well-known examples of this are allosteric regulation of protein activity and ligand-induced conformational changes in protein receptors. Detailed knowledge of the conformational properties of proteins is therefore pertinent to both basic and applied research, including drug development, since the majority of drugs target protein receptors and a growing number of drugs introduced to the market are therapeutic peptides or proteins. X-ray crystallography provides a static picture at atomic resolution of the lowest-energy structure of the native ensemble. There is a growing need for sensitive analytical tools to explore all of the significant molecular structures in the conformational landscape of proteins. Hydrogen/deuterium exchange monitored by mass spectrometry (HDX-MS) has recently emerged as a powerful method for characterizing protein conformational dynamics. The basis of this method is the fact that backbone amides in stable hydrogen-bonded structures (e.g., α-helices and β-sheets) are protected against exchange with the aqueous solvent. All protein structures are dynamic, however, and eventually all of the protecting hydrogen bonds will transiently break as the protein--according to thermodynamic principles--cycles through partially unfolded states that correspond to excited free energy levels. As a result, all of the backbone amides will eventually become temporarily solvent-exposed and exchange-competent over time. Consequently, a folded protein in D2O will gradually incorporate deuterium into its backbone amides, and the kinetics of the process can be readily monitored by mass spectrometry. The deuterium uptake kinetics for the intact protein (global exchange kinetics) represents the sum of the exchange kinetics for the individual backbone amides. Local exchange kinetics is typically achieved by using pepsin digestion under quench conditions (i.e., under cold

Pneumatic injector of deuterium macroparticles for TORE-SUPRA tokamak

International Nuclear Information System (INIS)

Vinyar, I.V.; Umov, A.P.; Lukin, A.Ya.; Skoblikov, S.V.; Reznichenko, P.V.; Krasil'nikov, I.A.

2006-01-01

The pneumatic injector for periodic injection of fuel-solid-deuterium pellets into the plasma of the TORE-SUPRA tokamak in a steady-state mode is described. The deuterium pellet injection with an unlimited duration is ensured by a screw extruder in which gaseous deuterium is frozen and squeezed outwards in the form of a rod with a rectangular cross section. A cutter installed on the injector's barrel cuts a cylinder with a diameter of 2 mm and a length of 1.0-3.5 mm out from this rod. The movement of the cutter is controlled by a pulsed electromagnetic drive at a pulse repetition rate of 10 Hz. In the injector's barrel, a compressed gas accelerates a deuterium pellet to a velocity of 100-650 m/s [ru

Synthesis of deuterium-labelled viloxazine. [Antidepressant

Energy Technology Data Exchange (ETDEWEB)

Mamada, Kumiko; Furuta, Takashi; Kasuya, Yasuji

1988-06-01

The synthesis of deuterium-labelled viloxazine with high isotopic purity is described. The synthetic procedures employ alkylation of 2-(benzyloxy)phenol with (/sup 2/H/sub 5/)ethyl iodide for the introduction of deuterium. Catalytic removal of the benzyl group of the deuterated product followed by reaction with epichlorohydrin afforded 1,2-epoxy-3-(2'-pentadeuteroethoxy-phenoxy)propane. Addition of 2-aminoethyl hydrogen sulphate to the epoxide and subsequent ring formation into a morpholine derivative produced the desired (/sup 2/H/sub 5/)viloxazine.

Continuum emission from irradiated solid deuterium

DEFF Research Database (Denmark)

Forrest, J.A.; Brooks, R.L.; Hunt, J.L.

1992-01-01

A new emission feature from the spectrum of irradiated solid deuterium has been observed in the very near-infrared spectral region. Experiments from three laboratories, using different excitation conditions, have confirmed the observation. Comparison of the timing and temperature dependence...... of the spectral feature to the information previously available from electron spin resonance studies of solid deuterium, points to atomic association as the underlying cause. We shall show the connection of this emission to the occurrence of thermal spikes and optical flashes, previously observed in solid...

Deuterium gas-driven permeation and subsequent retention in rolled tungsten foils

Energy Technology Data Exchange (ETDEWEB)

Liu, Feng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Zhou, Haishan [Department of Fusion Science, The Graduate University for Advanced Studies, Toki 509-5292 (Japan); Li, Xiao-Chun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Xu, Yuping; An, Zhongqing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230026 (China); Mao, Hongmin; Xing, Wenjing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Hou, Qing [Key Laboratory for Radiation Physics and Technology, Sichuan University, Chengdu 610061 (China); Luo, Guang-Nan, E-mail: gnluo@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230026 (China)

2014-12-15

Experiments concerning deuterium gas-driven permeation through rolled tungsten foils in the temperature range of 850–950 K and subsequent deuterium retention have been performed. The steady state permeation flux of deuterium is proportional to the square root of the driving pressure. The permeability of deuterium is in an order of 10{sup −14} mol m{sup −1} s{sup −1} Pa{sup −1/2} in this temperature range and the activation energy for permeation is 1.21 eV. Measurements of diffusivity are significantly affected by the driving pressure, which can be well explained by a saturable-trap model. Thermal desorption spectra of samples feature a single deuterium release peak at about 873 K. TMAP 4 modeling of this peak gives a detrapping energy of 1.70 eV, which fits the dissociation enthalpy of deuterium desorbing from the inner wall of vacancy clusters or pores in tungsten.

Neutron penumbral imaging of laser-fusion targets

International Nuclear Information System (INIS)

Lerche, R.A.; Ress, D.B.

1988-01-01

Using a new technique, penumbral coded-aperture imaging, the first neutron images of laser-driven, inertial-confinement fusion targets were obtained. With these images the deuterium-tritium burn region within a compressed target can be measured directly. 4 references, 11 figures

Deuterium electrodisintegration at high recoil momentum

International Nuclear Information System (INIS)

Steenholen, G.

1996-01-01

The availability of continuous electron beams made it possible to carry out various deuterium electro-disintegration experiments in kinematical domains corresponding to a high recoil momentum. Three such experiments are discussed: 1) the left-right asymmetry with respect to the direction of the momentum transfer has been measured with good precision; 2) cross sections have been obtained in a kinematical region well above the quasi-elastic peak; 3) data have been taken in quasi-elastic kinematics that can be used to study high-momentum components in the deuterium wave function [ru

Experimental Determination of the Possible Deuterium - Deuterium Fusion Reaction Originated in a Single Cavitation Bubble Luminescence System Using CDCL3 and D2 O

International Nuclear Information System (INIS)

Barbaglia, Mario; Florido, Pablo; Mayer, Roberto; Bonetto, Fabian

2003-01-01

We focus this work on the measurement of the possible Deuterium - Deuterium reaction in a SCBL (Single Cavitation Bubble Luminescence) system.We measure the possible reaction at the bubble generation time and at the bubble collapse time. We use a Nd:YAG laser and CDCl 3 and D 2 O as a medium to generate the bubble. Since CDCl 3 accommodation coefficient is best than that of D 2 O, it is expected a greater collapse force than using D 2 O.To benefit the bubble collapse violence, we diminish the temperature of the liquids.To avoid false neutron detection, we developed a measuring system with high background reject using the characteristic experiment times.No neutrons attributable to Deuterium - Deuterium fusion reaction were measured

Laser driven source of spin polarized atomic deuterium and hydrogen

International Nuclear Information System (INIS)

Poelker, M.; Coulter, K.P.; Holt, R.J.

1993-01-01

Optical pumping of potassium atoms in the presence of a high magnetic field followed by spin exchange collisions with deuterium (hydrogen) is shown to yield a high flux of spin polarized atomic deuterium (hydrogen). The performance of the laser driven source has been characterized as a function of deuterium (hydrogen) flow rate, potassium density, pump laser power, and magnetic field. Under appropriate conditions, the authors have observed deuterium atomic polarization as high as 75% at a flow rate 4.2x10 17 atoms/second. Preliminary results suggest that high nuclear polarizations are obtained in the absence of weak field rf transitions as a result of a spin temperature distribution that evolves through frequent H-H (D-D) collisions

Deuterium in atmospheric cycle

International Nuclear Information System (INIS)

Pontikis, M.C.

Interest of the study concerning the deuterium content variation (HDO) in the atmospheric water. Standards and measurement methods. Molecule HDO cycle in the atmospheric water. Application to the study of hail-generating cumulus-nimbus and of the mantle of snow [fr

Deuterium trapping in ion implanted and co-deposited beryllium oxide layers

International Nuclear Information System (INIS)

Markin, A.V.; Gorodetsky, A.E.; Zakharov, A.P.; Wu, C.H.

2000-01-01

Deuterium trapping in beryllium oxide films irradiated with 400 eV D ions has been studied by thermal desorption spectroscopy (TDS). It has been found that for thermally grown BeO films implanted in the range 300 - 900 K the total deuterium retention doesn't depend whereas TDS spectra do markedly on irradiation temperature. For R.T. implantation the deuterium is released in a wide range from 500 to 1100 K. At implantation above 600 K the main portion of retained deuterium is released in a single peak centered at about 1000 K. The similar TDS peak is measured for D/BeO co-deposited layer. In addition we correlate our implantation data on BeO with the relevant data on beryllium metal and carbon. The interrelations between deuterium retention and microstructure are discussed. (orig.)

Trapping behaviour of deuterium ions implanted into tungsten simultaneously with carbon ions

International Nuclear Information System (INIS)

Kobayashi, Makoto; Suzuki, Sachiko; Wang, Wanjing; Kurata, Rie; Kida, Katsuya; Oya, Yasuhisa; Okuno, Kenji; Ashikawa, Naoko; Sagara, Akio; Yoshida, Naoaki

2009-01-01

The trapping behaviour of deuterium ions implanted into tungsten simultaneously with carbon ions was investigated by thermal desorption spectroscopy (TDS) and x-ray photoelectron spectroscopy (XPS). The D 2 TDS spectrum consisted of three desorption stages, namely desorption of deuterium trapped by intrinsic defects, ion-induced defects and carbon with the formation of the C-D bond. Although the deuterium retention trapped by intrinsic defects was almost constant, that by ion-induced defects increased as the ion fluence increased. The retention of deuterium with the formation of the C-D bond was saturated at an ion fluence of 0.5x10 22 D + m -2 , where the major process was changed from the sputtering of tungsten with the formation of a W-C mixture to the formation of a C-C layer, and deuterium retention as the C-D bond decreased. It was concluded that the C-C layer would enhance the chemical sputtering of carbon with deuterium with the formation of CD x and the chemical state of carbon would control the deuterium retention in tungsten under C + -D 2 + implantation.

A study of inclusive charged current neutrino interactions in deuterium

International Nuclear Information System (INIS)

Visser, C.P.

1986-01-01

In this thesis the results of an analysis of inclusive neutrino and antineutrino interaction on deuterium nuclei are presented. The use of deuterium as a target provides a mean to study proton and neutron scattering separately. The presently accepted theory of electro-weak interactions is reviewed. Applications of the quark-parton model in the context of deep-inelastic neutrino interactions on nucleons are summarized. The concept of scaling and its consequences are treated, together with some sources of violation of scaling. The properties of the CERN wide-band neutrino beam and an overview of the elements of this beam are given. The method to determine the energy distribution and the composition of the neutrino and antineutrino beam is described. The technique employed to separate neutrino interactions on protons and neutrons is discussed. Results of the measurement of the total nucleon charged-current cross-sections and differential cross-sections are presented. The relative contributions of quarks and antiquarks to the neutrino cross-sections are deduced from y-distributions and compared to those obtained from the total cross-section measurements. Finally, the analysis of the structure functions is given. (Auth.)

Thermal desorption of deuterium from Be, and Be with helium bubbles

Energy Technology Data Exchange (ETDEWEB)

Fedorov, A.V.; Van Veen, A.; Busker, G.J. [Delft Univ. of Technology (Netherlands). Interfaculty Reactor Inst.

1998-01-01

Deuterium desorption measurements carried out on a single-crystalline beryllium sample are presented. Deuterium ions were implanted at room temperature at the energy of 0.7 and 1.2 keV up to doses ranging from 10{sup 19} to 3.6 x 10{sup 21} m{sup -2}. In order to eliminate the influence of the beryllium-oxide surface layer, before the implantation the surface of the sample was cleaned by argon sputtering. After the implantation the sample was annealed up to 1200 K at a constant rate of 10 K/s. Deuterium released from the sample was monitored by a calibrated quadrupole mass-spectrometer. The desorption spectra revealed two different contributions. One is a well defined and very narrow peak centered around 450 K. This peak is observed only at high implantation doses > 7.8 x 10{sup 20} m{sup -2}, which is close to the deuterium saturation limit of 0.3 D/Be and is related to deuterium release from blisters or interconnected bubbles. The activation energy of 1.1 eV and the threshold implantation dose are consistent with the values reported in literature. The second contribution in the release spectra is found in the temperature range from 600 to 900 K and is present throughout the whole range of the implantation doses. The activation energies corresponding to this release lie in the range between 1.8 and 2.5 eV and are ascribed to the release from deuterium-vacancy type of defects. In a number of experiments the deuterium implantation was preceded by helium implantation followed by partial annealing to create helium bubbles. The resulting deuterium desorption spectra indicate that deuterium detrapping from helium bubbles is characterized by an activation energy of 2.7 eV. (author)

Neutrino disintegration of deuterium

International Nuclear Information System (INIS)

Ying, S.; Haxton, W.; Henley, E.M.

1989-01-01

We calculate the rate of both neutral- and charged-current neutrino and antineutrino disintegration of deuterium. These rates are of interest for solar 8 B and hep ( 3 He + p) spectra and supernovae neutrinos, and are relevant for the Sudbury Neutrino Observatory (SNO)

Partial molar volumes of hydrogen and deuterium in niobium and vanadium

International Nuclear Information System (INIS)

Herro, H.M.

1979-01-01

Lattice dilation studies and direct pressure experiments gave comparable values for the partial molar volumes of hydrogen and deuterium in niobium and vanadium. Small isotope effects in the partial molar volume of hydrogen were measured in both metals by the differential isotope method. Hydrogen had a larger partial molar volume than deuterium in niobium, but the reverse was true in vanadium. The isotope effect measured in niobium can be represented as being due to the larger amplitude of vibration of the hydrogen atom than the deuterium atom in the metal lattice. Since hydrogen has a larger mean displacement from the equilibrium position than does deuterium, the average force hydrogen exerts on the metal atoms is greater than the force deuterium exerts. The isotope effect in vanadium is likely a result of anharmonic effects in the lattice and local vibrational modes

Influence of tungsten microstructure and ion flux on deuterium plasma-induced surface modifications and deuterium retention

Energy Technology Data Exchange (ETDEWEB)

Buzi, Luxherta [IEK - Plasmaphysik, Forschungszentrum Juelich GmbH, Association EURATOM-FZJ, Juelich (Germany); FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research (Netherlands); Ghent University (Belgium); Temmerman, Greg de [FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research (Netherlands); Reinhart, Michael; Matveev, Dmitry; Unterberg, Bernhard; Wienhold, Peter; Breuer, Uwe; Kreter, Arkadi [IEK - Plasmaphysik, Forschungszentrum Juelich GmbH, Association EURATOM-FZJ, Juelich (Germany); Oost, Guido van [Ghent University (Belgium)

2014-07-01

Tungsten is to be used as plasma-facing material for the ITER divertor due to its favourable thermal properties, low erosion and fuel retention. Bombardment of tungsten by low energy ions of hydrogen isotopes, at different surface temperature, can lead to surface modifications and influence the fuel accumulation in the material. This contribution will assess the impact of material microstructure and the correlation between the particle flux, surface modifications and deuterium retention in tungsten. Tungsten samples were exposed to deuterium plasma at a surface temperature of 510 K, 670 K and 870 K, ion energy of 40 eV and ion fluence of 10{sup 26} m{sup -2}. The high and low ion flux ranges were in the order 10{sup 24} m{sup -2}s{sup -1} and 10{sup 22} m{sup -2}s{sup -1}. Depth profiling of deuterium in all the samples was done by secondary ion mass spectroscopy technique and a scanning electron microscope was used to investigate the surface modifications. Modelling of the D desorption spectra with the coupled reaction diffusion system model will be also presented.

Process for recovering water enriched with deuterium

International Nuclear Information System (INIS)

Mandel, H.

1975-01-01

By the process proposed herewith, enrichment of deuterium in water by cooling water recirculation through series-connection of several cooling ciruits in the form of columns is obtained. With this method, conventional, open-type cooling towers without special installations can be applied, which is an important advantage as compared with a formerly proposed single-stage process with specially designed, complicated cooling towers. Series-connection of the cooling towers is carried out in such a way that the circulating water of a certain cooling circuit, which has a corresponding output value of deuterium enrichment, is conveyed to a succeeding circuit where further enrichment is achieved. The water enriched with deuterium is removed from the last cooling circuit of the series while an amount of fresch water equivalent to the water removed or evaporated altogether is fed to the first circuit of the series. (RB) [de

Confinement and heating of a deuterium-tritium plasma

International Nuclear Information System (INIS)

Hawryluk, R.J.; Adler, H.; Alling, P.

1994-03-01

The Tokamak Fusion Test Reactor (TFTR) has performed initial high-power experiments with the plasma fueled by deuterium and tritium to nominally equal densities. Compared to pure deuterium plasmas, the energy stored in the electron and ions increased by ∼20%. These increases indicate improvements in confinement associated with the use of tritium and possibly heating of electrons by α-particles

Influence of temperature and plasma composition on deuterium retention in refractory metals

International Nuclear Information System (INIS)

Alves, E.; Alves, L.C.; Barradas, N.P.; Mateus, R.; Carvalho, P.A.; Wright, G.M.

2010-01-01

Refractory materials are being considered potential candidates to build the first wall of the fusion reactor chamber. This work reports on the results of the study of tungsten and molybdenum metals exposed to high flux densities (∼10 24 D/m 2 s) and low temperature (T e ∼ 3 eV) deuterium plasmas in Pilot-PSI irradiation facility. The hydrogenic retention in poly-crystalline W and Mo targets was studied with 3 He nuclear reaction analyses (NRA). The NRA results clearly show a two-dimensional radial distribution of the deuterium with a minimum at the center and a maximum close to the edge. These distribution correlates well with the thermal profile of the sample surface, where a maximum of ∼1600 K was measured at the center decreasing to ∼1000 K in the edges. A maximum deuterium fluence retention of 5 x 10 15 D/cm 2 was measured. The values of the retained fractions ranging from 10 -5 to 10 -6 D retained /D incident were measured with thermal desorption spectroscopy (TDS) and compares well with IBA results. Moreover, the presence of C in the plasma and its co-deposition increases the D retention in the region where a C film is formed. Both NRA and TDS results show no clear dependence of retention on incident fluence suggesting the absence of plasma related traps in W under these conditions.

Consumption of potassium permanganate by impurities in deuterium oxide

International Nuclear Information System (INIS)

Anon.

1981-01-01

The titrimetric measurement of the consumption of potassium permanganate by impurities in deuterium oxide is one of the required methods intended for use in establishing whether the deuterium oxide is of sufficient purity to meet specifications. The method includes a discussion of reagents, procedure, and calculation

Trapping of deuterium in krypton-implanted nickel

International Nuclear Information System (INIS)

Frank, R.C.; McManus, S.P.; Rehn, L.E.; Baldo, P.

1986-01-01

Krypton ions with energy 600 keV were implanted in nickel to fluences of 2 x 10 16 cm -2 under three different conditions. Deuterium was subsequently introduced into the implanted regions by electrolysis at room temperature. After the diffusible deuterium was permitted to escape, the 2 H( 3 He, 1 H) 4 He nuclear reaction was used to analyze for the trapped deuterium during an isochronal annealing program. The region implanted at 100 0 C with no higher temperature anneal had the largest number of traps; the region implanted at 100 0 C and annealed for 100 min at 500 0 C had considerably less; the region implanted at 500 0 C had the least. Electron diffraction patterns confirmed the existence of solid crystalline krypton in all three regions. Transmission electron microscope studies revealed precipitates with an average diameter of 8 nm in the region implanted at 500 0 C. The two regions implanted at 100 0 C contained smaller precipitates. Trap binding enthalpies were obtained by math modeling. In addition to the traps with binding enthalpy of 0.55 eV reported earlier by other investigators for helium implanted in nickel, a smaller number of traps with binding enthalpies up to 0.83 eV were also found. The trapping of deuterium by various types of imperfections, including the solid krypton precipitates, is discussed

Development of positron annihilation spectroscopy for investigating deuterium decorated voids in neutron-irradiated tungsten

Energy Technology Data Exchange (ETDEWEB)

Taylor, C.N., E-mail: chase.taylor@inl.gov [Fusion Safety Program, Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Shimada, M.; Merrill, B.J. [Fusion Safety Program, Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Akers, D.W. [Experimental Programs, Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Hatano, Y. [Hydrogen Isotope Research Center, University of Toyama, Toyama 930-8555 (Japan)

2015-08-15

The present work is a continuation of a recent research to develop and optimize positron annihilation spectroscopy (PAS) for characterizing neutron-irradiated tungsten. Tungsten samples were exposed to neutrons in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory and damaged to 0.025 and 0.3 dpa. Subsequently, they were exposed to deuterium plasmas in the Tritium Plasma Experiment (TPE) at Idaho National Laboratory. The implanted deuterium was desorbed through sample heating to 900 °C, and Doppler broadening (DB)-PAS was performed both before and after heating. Results show that deuterium impregnated tungsten is identified as having a smaller S-parameter. The S-parameter increases after deuterium desorption. Microstructural changes also occur during sample heating. These effects can be isolated from deuterium desorption by comparing the S-parameters from the deuterium-free back face with the deuterium-implanted front face. The application of using DB-PAS to examine deuterium retention in tungsten is examined.

Development of positron annihilation spectroscopy for investigating deuterium decorated voids in neutron-irradiated tungsten

Science.gov (United States)

Taylor, C. N.; Shimada, M.; Merrill, B. J.; Akers, D. W.; Hatano, Y.

2015-08-01

The present work is a continuation of a recent research to develop and optimize positron annihilation spectroscopy (PAS) for characterizing neutron-irradiated tungsten. Tungsten samples were exposed to neutrons in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory and damaged to 0.025 and 0.3 dpa. Subsequently, they were exposed to deuterium plasmas in the Tritium Plasma Experiment (TPE) at Idaho National Laboratory. The implanted deuterium was desorbed through sample heating to 900 °C, and Doppler broadening (DB)-PAS was performed both before and after heating. Results show that deuterium impregnated tungsten is identified as having a smaller S-parameter. The S-parameter increases after deuterium desorption. Microstructural changes also occur during sample heating. These effects can be isolated from deuterium desorption by comparing the S-parameters from the deuterium-free back face with the deuterium-implanted front face. The application of using DB-PAS to examine deuterium retention in tungsten is examined.

Influence of deuterium content on tensile behavior of Zr-2.5Nb pressure tube material in the temperature range of ambient to 300 degC

International Nuclear Information System (INIS)

Bind, A.K.; Singh, R.N.; Chakravartty, J.K.; Dhandharia, Priyesh; Ghosh, Agnish; More, Nitin S.; Chhatre, A.G.; Vijayakumar, S.

2011-08-01

Tensile properties of autoclaved zirconium-2.5 wt. % niobium pressure tube material were evaluated by uniaxial tension tests at temperatures between 25 and 300 degC and under strain-rates of 1.075 x 10 -4 /s. Six number of Zr-2.5Nb alloy pressure tube spools of length 130 mm were obtained from pressure tube number 19-2557-2. Five spools were polished with abrasive paper to remove the oxide layer. These spools were gaseously charged with controlled amount of deuterium. The target deuterium concentrations were 25, 50, 75, 100 and 200 wppm of hydrogen equivalent. Ten samples were machined by EDM wire cutting from every spool. The tensile specimen axis was oriented along longitudinal direction of the tube. Metallographic examination of the deuterium charged samples suggested that the deuterides were predominantly circumferential deuterides. Analysis of tensile results showed that both yield and ultimate tensile strengths of this alloy decreased monotonically with increasing test temperatures. The tensile ductility decreased marginally with increase in test temperature from ambient to 300 degC. It was also observed that both strength and ductility appear to be unaffected by deuterium content at all temperatures, thereby suggesting that at least up to 200 wppm (Heq.) of deuterium tensile properties are not influenced by deuterium. (author)

Vibrational modes of deuterium in KD2PO4

International Nuclear Information System (INIS)

Mizoguchi, Kohji; Agui, Akane; Tominaga, Yasunori; Nakai, Yusuke; Ikeda, Susumu.

1993-01-01

In order to study the deuteration effect in hydrogen-bonded compounds such as KH 2 PO 4 , hydrogen and deuterium modes in KH 2 PO 4 and K(D x H 1-x ) 2 PO 4 (x = 95 %) were investigated by means of inelastic neutron-scattering measurements over a wide energy range. By comparing Raman spectra of KH 2 PO 4 and KD 2 PO 4 with neutron-scattering spectra, the vibrational modes of deuterium and those of PO 4 tetrahedrons in the energy range of 30 < ε < 150 meV have been investigated. At least two deuterium modes have been found at 87 meV and 106 meV. (author)

Electromigration of hydrogen and deuterium in vanadium, niobium, and tantalum

International Nuclear Information System (INIS)

Jensen, C.L.

1977-10-01

The electric mobility and effective valence of hydrogen and deuterium in vanadium, niobium, tantalum and three niobium-tantalum alloys were measured. A resistance technique was used to directly determine the electric mobility of hydrogen and deuterium at 30 0 C while a steady-state method was used to measure the effective valence. The use of mass spectrographic techniques on a single specimen which contained both hydrogen and deuterium greatly increased the precision with which the isotope effect in the effective valence could be measured

Measurement of high-pressure shock waves in cryogenic deuterium-tritium ice layered capsule implosions on NIF.

Science.gov (United States)

Robey, H F; Moody, J D; Celliers, P M; Ross, J S; Ralph, J; Le Pape, S; Berzak Hopkins, L; Parham, T; Sater, J; Mapoles, E R; Holunga, D M; Walters, C F; Haid, B J; Kozioziemski, B J; Dylla-Spears, R J; Krauter, K G; Frieders, G; Ross, G; Bowers, M W; Strozzi, D J; Yoxall, B E; Hamza, A V; Dzenitis, B; Bhandarkar, S D; Young, B; Van Wonterghem, B M; Atherton, L J; Landen, O L; Edwards, M J; Boehly, T R

2013-08-09

The first measurements of multiple, high-pressure shock waves in cryogenic deuterium-tritium (DT) ice layered capsule implosions on the National Ignition Facility have been performed. The strength and relative timing of these shocks must be adjusted to very high precision in order to keep the DT fuel entropy low and compressibility high. All previous measurements of shock timing in inertial confinement fusion implosions [T. R. Boehly et al., Phys. Rev. Lett. 106, 195005 (2011), H. F. Robey et al., Phys. Rev. Lett. 108, 215004 (2012)] have been performed in surrogate targets, where the solid DT ice shell and central DT gas regions were replaced with a continuous liquid deuterium (D2) fill. This report presents the first experimental validation of the assumptions underlying this surrogate technique.

Thermodynamic properties of solid deuterium in premelting region

International Nuclear Information System (INIS)

Udovichenko, B.G.; Esel'son, V.B.; Manzhelij, V.G.

1984-01-01

Thermal expansion and isothermal compressibility of solid normal deuterium are measured near the melting line under pressures up to 500 atm. The earlier measurement method is improved to operate in a wider range of working pressures. The effects are discussed which are produced by zero trranslational oscillations in the thermodynamic properties of deuterium. The change in the molar volume in the range from T=0 to the melting temperature is considered as a quantum characteristic of the crystal. The molar volumes of solid deuterium observed at the melting line at moderate P are compared and specified. At P=O and T=0 the molar volume of o-D 2 is found to be V 00 =(20.03+-0.07) cm 3 /mole which follows from the thermodynamic experiment

Deuterium microscopy using 17 MeV deuteron–deuteron scattering

Energy Technology Data Exchange (ETDEWEB)

Reichart, Patrick, E-mail: patrick.reichart@unibw.de; Moser, Marcus; Greubel, Christoph; Peeper, Katrin; Dollinger, Günther, E-mail: guenther.dollinger@unibw.de

2016-03-15

Using 17 MeV deuterons as a micrometer focused primary beam, we performed deuterium microscopy by using the deuteron–deuteron (dd) scattering reaction. We describe our new box like detector setup consisting of four double sided silicon strip detectors (DSSSD) with 16 strips on each side, each covering up to 0.5 sr solid angle for coincidence detection. This method becomes a valuable tool for studies of hydrogen incorporation or dynamic processes using deuterium tagging. The background from natural hydrocarbon or water contamination is reduced by the factor 150 ppm of natural abundance of deuterium in hydrogen. Deuterium energies of up to 25 MeV, available at the microprobe SNAKE, are ideal for the analysis of thin freestanding samples so that the scattered particles are transmitted to the detector. The differential cross section for the elastic scattering reaction is about the same as for pp-scattering (~100 mb/sr). The main background due to nuclear reactions is outside the energy window of interest. Deuteron–proton (dp) scattering events give an additional signal for hydrogen atoms, so the H/D-ratio can be monitored in parallel. A deuterium detection limit due to accidental coincidences of 3 at-ppm down to less than 1 at-ppm is demonstrated on deuterated polypropylen sheets as well as thick polycarbonate sheets after various stages of coincidence filtering that is possible with our granular detector.

Selected bibliography on deuterium isotope effects and heavy water

International Nuclear Information System (INIS)

Dave, S.M.; Donde, M.M.

1983-01-01

In recent years, there has been a great deal of interest in using deuterium and heavy water not only in nuclear industry but also in various fields of basic as well as applied research in physics, chemistry and biology. As a result, the literature is being enriched with a large number of research papers and technical reports published each year. Thus, to enable the scientists to have an easy reference to these works, an endeavour has been made in this selected bibliography, to enlist the publications related to these fields. Since the interest is concerned mainly with heavy water production processes, deuterium isotope effects etc., several aspects (e.g. nuclear) of deuterium have not been covered here. The material in this bibliography which cites 2388 references has been classified under six broad headings, viz. (1) Production of heavy water, (2) Study of deuterium isotope effects, (3) Analysis and Properties of heavy water, (4) Laser Separation of deuterium, (5) Isotopic exchange reactions, and (6) Miscellaneous. The sources of information used for this compilation are chemical abstracts, nuclear science abstracts, INIS Atomindex and also some scattered search through journals and reports available in the B.A.R.C. library. However, in spite of sincere attempts for a wide coverage, no claim is being made towards the exhaustiveness of this bibliography. (author)

Mechanism and deuterium pickup in Zr-2.5Nb alloy

International Nuclear Information System (INIS)

Ploc, R.A.

1999-12-01

There are approximately 400 Zr-2.5Nb pressure tubes in a CANDU reactor. During operation, the pressure tubes contain heavy water at about 300 deg C, 10.3 NPa with a room-temperature pD of 10.5. Operation of the pressure tube in the environment leads to oxide formation and absorption of deuterium. Excess deuterium absorption leads to precipitation of zirconium deuterides in the metal. A knowledge of how the deuterium passes through the oxide film to enter into the metal is an important step in gaining control over ingress rates. Fresnel fringe imaging of cross-sectioned oxides grown on pressure tubes, combined with tilting in the electron microscope, has revealed the three-dimensional nature of porosity in the oxide films. Two primary types exist, flake and ribbon. The main route for deuterium ingress is via ribbon porosity, as shown by electrochemical impedance spectroscopy. The location of the ribbon porosity is along the boundary between the oxidized α-Zr and β-Zr phases. Modifications to reduce ribbon porosity are possible and this, in turn, leads to significantly lower rates of deuterium absorption and extension of pressure-tube lifetime. (author)

Effects of hydrogen mixture into helium gas on deuterium removal from lithium titanate

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, Akihito, E-mail: tsuchiya@frontier.hokudai.ac.jp [Laboratory of Plasma Physics and Engineering, Hokkaido University, Kita-13, Nishi-8, Kita-ku, Sapporo 060-8628 (Japan); Hino, Tomoaki; Yamauchi, Yuji; Nobuta, Yuji [Laboratory of Plasma Physics and Engineering, Hokkaido University, Kita-13, Nishi-8, Kita-ku, Sapporo 060-8628 (Japan); Akiba, Masato; Enoeda, Mikio [Japan Atomic Energy Agency, 801-1, Mukoyama, Naka 311-0193 (Japan)

2013-10-15

Lithium titanate (Li{sub 2}TiO{sub 3}) pebbles were irradiated with deuterium ions with energy of 1.7 keV and then exposed to helium or helium–hydrogen mixed gas at various temperatures, in order to evaluate the effects of gas exposure on deuterium removal from the pebbles. The amounts of residual deuterium in the pebbles were measured by thermal desorption spectroscopy. The mixing of hydrogen gas into helium gas enhanced the removal amount of deuterium. In other words, the amount of residual deuterium after the helium–hydrogen mixed gas exposure at lower temperature was lower than that after the helium gas exposure. In addition, we also evaluated the pebbles exposed to the helium gas with different hydrogen mixture ratio from 0% to 1%, at 573 K. Although the amount of residual deuterium in the pebbles after the exposure decreased with increasing the hydrogen mixture ratio, the implanted deuterium partly remained after the exposure. These results suggest that the tritium inventory may occur at low temperature region in the blanket during the operation.

Method to separate deuterium isotopes using ethylene and ethylene dichloride

International Nuclear Information System (INIS)

Benson, S.W.

1979-01-01

The separation of deuterium by the dissociation of ethylene vinyl chloride, 1,2-dichloro-ethanes or propylene with the help of intensive, matched infrared lasers enables a relatively good yield if operated on a large scale, e.g. in refineries with large through-put. The deuterium from the laser photolysis of ethylene and vinyl chloride is found in the acetylene formed, which has to be separated off and processed. When using dichloroehtane, the deuterium is found in the vinal chloride formed. The methods are briefly described. (UWI) [de

Shock timing measurements and analysis in deuterium-tritium-ice layered capsule implosions on NIF

Energy Technology Data Exchange (ETDEWEB)

Robey, H. F.; Celliers, P. M.; Moody, J. D.; Sater, J.; Parham, T.; Kozioziemski, B.; Dylla-Spears, R.; Ross, J. S.; LePape, S.; Ralph, J. E.; Dewald, E. L.; Berzak Hopkins, L.; Kroll, J. J.; Yoxall, B. E.; Hamza, A. V.; Landen, O. L.; Edwards, M. J. [Lawrence Livermore National Laboratory, Livermore, California 94551 (United States); Hohenberger, M.; Boehly, T. R. [Laboratory for Laser Energetics, Rochester, New York 14623 (United States); Nikroo, A. [General Atomics, San Diego, California 92196 (United States)

2014-02-15

Recent advances in shock timing experiments and analysis techniques now enable shock measurements to be performed in cryogenic deuterium-tritium (DT) ice layered capsule implosions on the National Ignition Facility (NIF). Previous measurements of shock timing in inertial confinement fusion implosions [Boehly et al., Phys. Rev. Lett. 106, 195005 (2011); Robey et al., Phys. Rev. Lett. 108, 215004 (2012)] were performed in surrogate targets, where the solid DT ice shell and central DT gas were replaced with a continuous liquid deuterium (D2) fill. These previous experiments pose two surrogacy issues: a material surrogacy due to the difference of species (D2 vs. DT) and densities of the materials used and a geometric surrogacy due to presence of an additional interface (ice/gas) previously absent in the liquid-filled targets. This report presents experimental data and a new analysis method for validating the assumptions underlying this surrogate technique. Comparison of the data with simulation shows good agreement for the timing of the first three shocks, but reveals a considerable discrepancy in the timing of the 4th shock in DT ice layered implosions. Electron preheat is examined as a potential cause of the observed discrepancy in the 4th shock timing.

Shock timing measurements and analysis in deuterium-tritium-ice layered capsule implosions on NIF

Science.gov (United States)

Robey, H. F.; Celliers, P. M.; Moody, J. D.; Sater, J.; Parham, T.; Kozioziemski, B.; Dylla-Spears, R.; Ross, J. S.; LePape, S.; Ralph, J. E.; Hohenberger, M.; Dewald, E. L.; Berzak Hopkins, L.; Kroll, J. J.; Yoxall, B. E.; Hamza, A. V.; Boehly, T. R.; Nikroo, A.; Landen, O. L.; Edwards, M. J.

2014-02-01

Recent advances in shock timing experiments and analysis techniques now enable shock measurements to be performed in cryogenic deuterium-tritium (DT) ice layered capsule implosions on the National Ignition Facility (NIF). Previous measurements of shock timing in inertial confinement fusion implosions [Boehly et al., Phys. Rev. Lett. 106, 195005 (2011); Robey et al., Phys. Rev. Lett. 108, 215004 (2012)] were performed in surrogate targets, where the solid DT ice shell and central DT gas were replaced with a continuous liquid deuterium (D2) fill. These previous experiments pose two surrogacy issues: a material surrogacy due to the difference of species (D2 vs. DT) and densities of the materials used and a geometric surrogacy due to presence of an additional interface (ice/gas) previously absent in the liquid-filled targets. This report presents experimental data and a new analysis method for validating the assumptions underlying this surrogate technique. Comparison of the data with simulation shows good agreement for the timing of the first three shocks, but reveals a considerable discrepancy in the timing of the 4th shock in DT ice layered implosions. Electron preheat is examined as a potential cause of the observed discrepancy in the 4th shock timing.

Shock timing measurements and analysis in deuterium-tritium-ice layered capsule implosions on NIF

International Nuclear Information System (INIS)

Robey, H. F.; Celliers, P. M.; Moody, J. D.; Sater, J.; Parham, T.; Kozioziemski, B.; Dylla-Spears, R.; Ross, J. S.; LePape, S.; Ralph, J. E.; Dewald, E. L.; Berzak Hopkins, L.; Kroll, J. J.; Yoxall, B. E.; Hamza, A. V.; Landen, O. L.; Edwards, M. J.; Hohenberger, M.; Boehly, T. R.; Nikroo, A.

2014-01-01

Recent advances in shock timing experiments and analysis techniques now enable shock measurements to be performed in cryogenic deuterium-tritium (DT) ice layered capsule implosions on the National Ignition Facility (NIF). Previous measurements of shock timing in inertial confinement fusion implosions [Boehly et al., Phys. Rev. Lett. 106, 195005 (2011); Robey et al., Phys. Rev. Lett. 108, 215004 (2012)] were performed in surrogate targets, where the solid DT ice shell and central DT gas were replaced with a continuous liquid deuterium (D2) fill. These previous experiments pose two surrogacy issues: a material surrogacy due to the difference of species (D2 vs. DT) and densities of the materials used and a geometric surrogacy due to presence of an additional interface (ice/gas) previously absent in the liquid-filled targets. This report presents experimental data and a new analysis method for validating the assumptions underlying this surrogate technique. Comparison of the data with simulation shows good agreement for the timing of the first three shocks, but reveals a considerable discrepancy in the timing of the 4th shock in DT ice layered implosions. Electron preheat is examined as a potential cause of the observed discrepancy in the 4th shock timing

Strong isotope effects on the charge transfer in slow collisions of He2+ with atomic hydrogen, deuterium, and tritium

NARCIS (Netherlands)

Stolterfoht, N.; Cabrera-Trujillo, R.; Oehrn, Y.; Deumens, E.; Hoekstra, R.; Sabin, J. R.

2007-01-01

Probabilities and cross sections for charge transfer by He2+ impact on atomic hydrogen (H), deuterium (D), and tritium (T) at low collision energies are calculated. The results are obtained using an ab initio theory, which solves the time-dependent Schrodinger equation. For the H target, excellent

Deuterium implantation into Y{sub 2}O{sub 3}-doped and pure tungsten: Deuterium retention and blistering behavior

Energy Technology Data Exchange (ETDEWEB)

Zhao, M. [School of Materials Science and Engineering, University of Science and Technology, Beijing, Beijing 100083 (China); Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, Garching 85748 (Germany); Jacob, W., E-mail: wolfgang.jacob@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, Garching 85748 (Germany); Manhard, A.; Gao, L.; Balden, M.; Toussaint, U. von [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, Garching 85748 (Germany); Zhou, Z. [School of Materials Science and Engineering, University of Science and Technology, Beijing, Beijing 100083 (China)

2017-04-15

The blistering and near-surface deuterium retention of a Y{sub 2}O{sub 3}-doped tungsten (W) and two different pure W grades were studied after exposure to deuterium (D) plasma at elevated temperatures (370, 450 and 570 K). Samples were exposed to a deuterium fluence of 6 × 10{sup 24} D m{sup −2} applying a moderate ion flux of about 9 × 10{sup 19} D m{sup −2} s{sup −1} at an ion energy of 38 eV/D. Morphological modifications at the surface were analyzed by confocal laser scanning microscopy and scanning electron microscopy. The D depth profiles and the accumulated D inventories within the topmost 8 μm were determined by nuclear reaction analysis. Blistering and deuterium retention were strongly dependent on the implantation temperature. In addition, blistering was sensitively influenced by the used tungsten grade, although the total amount of retained D measured by nuclear reaction analysis was comparable. Among the three different investigated tungsten grades, Y{sub 2}O{sub 3}-doped W exhibited the lowest degree of surface modification despite a comparable total D retention. - Highlights: •Y{sub 2}O{sub 3}-doped W and 2 pure W were exposed to D plasma at 370, 450 and 570 K. •D retention in all 3 materials is comparable. •D plasma exposure leads to blister formation on all investigated W grades. •Blister morphology and size distribution depend strongly on W grade. •Y{sub 2}O{sub 3}-doped W shows the lowest degree of surface modification.

Deuterium absorption property of Al/Zr-V/Mo multifilms

International Nuclear Information System (INIS)

Wang Haifeng; Peng Shuming; Zhang Xiaohong; Long Xinggui; Yang Benfu

2005-01-01

Deuterium absorption property of Al/Zr-V/Mo multifilms was studied experimentally to explore the effect of Al film. There is only one desorption peak at 320 degree C for Al film, two desorption peaks at 220 degree C and 350 degree C for Zr-V film. When the average thickness of Al film is less than 0.6 μm, the desorption property of Al/Zr-V multifilms is just as Zr-V film, when it is more than 0.6 μm, just as Al film. Deuterium absorption by Al/Zr-V multifilms decreases as the thickness of Al film increases until 0.7 μm, then the deuterium absorption no longer changes significantly. The Al film of multifilms cracks on desorbing, so the absorption rate varies as Zr-V film when the thickness of Al film is less than 0.6 μ. When the thickness of Al film is more than 0.6 μm, the deuterium absorption rate of multifilm does not change with the thickness of Al film. (author)

Evidence for Nuclear Tensor Polarization of Deuterium Molecules in Storage Cells

International Nuclear Information System (INIS)

van den Brand, J.; Bulten, H.; Zhou, Z.; Unal, O.; van den Brand, J.; Ferro-Luzzi, M.; Botto, T.; Bouwhuis, M.; Heimberg, P.; de Jager, C.; de Lange, D.; Nooren, G.; Papadakis, N.; Passchier, I.; Poolman, H.; Steijger, J.; Vodinas, N.; de Vries, H.; van den Brand, J.; Ferro-Luzzi, M.; Lang, J.; Alarcon, R.; Dolfini, S.; Ent, R.; Higinbotham, D.

1997-01-01

Deuterium molecules were obtained by recombination, on a copper surface, of deuterium atoms prepared in specific hyperfine states. The molecules were stored for about 5ms in an open-ended cylindrical cell, placed in a 23mT magnetic field, and their tensor polarization was measured by elastic scattering of 704MeV electrons. The results of the measurements are consistent with the deuterium molecules retaining the tensor polarization of the initial atoms. copyright 1997 The American Physical Society

Direct depth distribution measurement of deuterium in bulk tungsten exposed to high-flux plasma

Directory of Open Access Journals (Sweden)

C. N. Taylor

2017-05-01

Full Text Available Understanding tritium retention and permeation in plasma-facing components is critical for fusion safety and fuel cycle control. Glow discharge optical emission spectroscopy (GD-OES is shown to be an effective tool to reveal the depth profile of deuterium in tungsten. Results confirm the detection of deuterium. A ∼46 μm depth profile revealed that the deuterium content decreased precipitously in the first 7 μm, and detectable amounts were observed to depths in excess of 20 μm. The large probing depth of GD-OES (up to 100s of μm enables studies not previously accessible to the more conventional techniques for investigating deuterium retention. Of particular applicability is the use of GD-OES to measure the depth profile for experiments where high deuterium concentration in the bulk material is expected: deuterium retention in neutron irradiated materials, and ultra-high deuterium fluences in burning plasma environment.

Recent experimental results on solutions of deuterium in lithium

International Nuclear Information System (INIS)

Ihle, H.R.; Wu, C.H.

1976-01-01

The existence of a number of stable molecules containing lithium and hydrogen isotopes in the saturated vapor over dilute solutions of hydrogen isotopes in lithium causes an unexpectedly high density of hydrogen isotopes in the vapor at high temperature. An evaluation of the partial pressures of the gas species Li, Li 2 , LiD, Li 2 D, LiD 2 and D 2 over solutions of deuterium in lithium measured in the temperature range 770 to 970 0 K, and extrapolation to higher temperatures, leads to the conclusion that the ratio of the atom fraction of deuterium in the gas to its atom fraction in the liquid exceeds unity above approximately 1240 0 K; this ratio is independent of the deuterium atom fraction in the liquid at low concentrations. Therefore the thermodynamic supposition that hydrogen isotopes can be separated from lithium by fractional distillation even at extremely low concentration exists. A direct verification of this phenomenon was made by Rayleigh distillation of Li-D solutions in the temperature range 970 to 1600 0 K. These measurements yield also the ratio of the deuterium atom fraction in the gas to that in the liquid and are in good agreement with the data obtained by extrapolation of partial pressures. The enrichment and depletion of deuterium in dependence on the number of theoretical plates of a distillation column at total reflux is calculated using the results

Determination of gluconeogenesis in man by the use of deuterium-NMR-spectroscopy

International Nuclear Information System (INIS)

Rosian, E.

2000-03-01

The aim of this dissertation is the quantification of the deuterium--distribution in human glucose by the use of the deuterium NMR spectroscopy of deuteriated water. The glucose production in human organism is composed of gluconeogenesis and glycolysis. The quantification of the part of gluconeogenesis on the total glucose production was determined by the use of deuterium NMR spectroscopy. (boteke)

Deuterium content of the Venus atmosphere

International Nuclear Information System (INIS)

Bertaux, -J.-L.; Clarke, J.T.

1989-01-01

The abundance of deuterium in the atmosphere of Venus is an important clue to the planet's history, because ordinary and deuterated water escape at different rates. Using the high-resolution mode of the International Ultraviolet Explorer (IUE), we measured hydrogen Lyman-α-emission but found only an upper limit on deuterium Lyman-α-emission, from which we inferred a D/H ratio of less than 2-5 x 10 -3 . This is smaller by a factor of 3-8 than the D/H ratio derived from measurements by the Pioneer Venus Large Probe, and may indicate either a stratification of D/H ratio with altitude or a smaller overall ratio than previously thought. (author)

Viscosity and attenuation of sound wave in high density deuterium

International Nuclear Information System (INIS)

Inoue, Kazuko; Ariyasu, Tomio

1985-01-01

The penetration of low frequency sound wave into the fuel deuterium is discussed as for laser fusion. The sound velocity and the attenuation constant due to viscosity are calculated for high density (n = 10 24 -- 10 27 cm -3 , T = 10 -1 -- 10 4 eV) deuterium. The shear viscosity of free electron gas and the bulk viscosity due to ion-ion interaction mainly contribute to the attenuation of sound wave. The sound wave of the frequency below 10 10 Hz can easily penetrate through the compressed fuel deuterium of diameter 1 -- 10 3 μm. (author)

Electromigration of hydrogen and deuterium in vanadium and niobium by a resistance method

International Nuclear Information System (INIS)

Peterson, D.T.; Jensen, C.L.

1978-01-01

The electric mobility of hydrogen and deuterium has been measured at 30 0 C in niobium (Cb) and vanadium by a resistance method. The electric mobility was found to be 5.7 x 10 -4 cm 2 /V-s for hydrogen and 2.8 x 10 -4 for deuterium in niobium. In vanadium the electric mobilities were 2.3 x 10 -3 and 1.3 x 10 -3 cm 2 /V-s for hydrogen and deuterium, respectively. The effective charges calculated using reported diffusion coefficients are positive and are slightly greater for deuterium than for hydrogen in both vanadium and niobium. The resistivity increase due to the hydrogen isotopes in vanadium and niobium was also measured. Hydrogen was found to contribute 0.65 μ ohm-cm/at. % and deuterium 0.58 μ ohm-cm/at. % to the resistivity of niobium. In vanadium, the solute resistivities were found to be 0.98 μ ohm-cm/at. % and 0.90 μ ohm-cm/at. % for hydrogen and deuterium, respectively

Neutron-diffraction localization of deuterium in Ti6OD0,45 alloy

International Nuclear Information System (INIS)

Sumin, V.V.; Fadeev, N.V.; Morozov, S.I.

1987-01-01

Attemp to localize hydrogen in TiO alloy octahedral internodes was made by independent method. To do this, deuterium and hydrogen interstitial solid solutions in titanium were studied by neutron-diffraction method. Deuterium localization in crystal lattice is considerably more reliable, than hydrogen localization due to low noncoherent cross-section of neutron scattering by deuterium. Phase analysis of TiO samples with different deuterium content has shown, that alloys remain singlephase, at least, up to D/O≤1/2 composition. Second phase presence in a sample was determined with accuracy of up to ∼1%, that was proved by phase mixing-in method. Deuterium distribution analysis was conducted for Ti 6 O alloy. It is shown, that presence of oxigen atoms within titanium matrix provides conditions for hydrogen and deuturium localization in octacell layers, which are partially filled with oxygen atoms. Here, hydrogen (Deuterium) forms with oxygen O-H pairs (D), placed in plane parallel to basis HCP of titanium lattice. The most possible characteristic distance between oxygen and hydrogen atoms constitutes a 0 =2,96A (a o -HCP parameter of Ti lattice in Ti 6 O alloy)

Correlation between abnormal deuterium flux and heat flow in a D/Pd system

International Nuclear Information System (INIS)

Li Xingzhong; Liu Bin; Tian Jian; Wei Qingming; Zhou Rui; Yu Zhiwu

2003-01-01

Deuterium flux through the thin wall of a palladium tube has been studied by monitoring gas pressure and temperature. A high-precision calorimeter (Calvet) was used to detect heat flow when the heater was shut down and the palladium tube was cooling down slowly. At certain temperatures an abnormal deuterium flux appeared. This deuterium flux reached a peak when the temperature of the palladium was decreasing. This abnormal deuterium flux differs from the monotonic feature of a normal diffusive flux and is accompanied by a heat flow

Production of polarized negative deuterium ion beam with dual optical pumping in KEK

Energy Technology Data Exchange (ETDEWEB)

Kinsho, M.; Ikegami, K.; Takagi, A. [National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan); Mori, Y.

1997-02-01

To obtain highly nuclear-spin vector polarized negative deuterium ion beam, a dual optically pumped polarized negative deuterium ion source has been developed at KEK. It is possible to select a pure nuclear-spin state with this scheme, and negative deuterium ion beam with 100% nuclear-spin vector polarization can be produced in principle. We have obtained about 70% of nuclear-spin vector polarized negative deuterium ion beam so far. This result may open up a new possibilities for the optically pumped polarized ion source. (author)

Synthesis of deuterium-labeled prochlorperazine.

Science.gov (United States)

Hawes, E M; Gurnsey, T S; Shetty, H U; Midha, K K

1983-06-01

The propylpiperazine side chain of prochlorperazine was labeled with two, four, or six deuterium atoms by lithium aluminum deuteride reduction of the appropriate amide. The isotopic purity of the products after correcting for chlorine isotopes was greater than 95.7%.

Deuterium used as artificial tracer in column studies under saturated water flow conditions

Science.gov (United States)

Koeniger, P.; Geiges, M.; Leibundgut, Ch.

2003-04-01

In contrast to numerous investigations using deuterium as an environmental tracer, hydrological investigations with deuterium-labelled water are rather rare. Currently applications in groundwater studies are restricted due to increasing costs of spiking large water quantities but an application as intelligent tracer might be of advantage especially in combination with other tracers and under distinct environmental conditions. Therefore deuterium was applied as artificial tracer in column experiments that are well proved as a tool to characterise tracer behaviour in recent studies. Deuterium was tested in comparison to the more familiar conservative tracer fluorescein. Varying experimental conditions, e.g. column length (0.5, 1.0, 1.5 m), initial tracer concentration (0.01, 0.02, 0.2 mg) and flow velocity (1.5 to 6.0 m/d) were used to investigate tracer behaviour under saturated water flow conditions. Deuterium was analysed using an H/Device with chrome reduction connected to an isotope ratio mass spectrometer and expressed in relative concentrations [per mill V-SMOW]. Theoretical tracer breakthrough curves were calculated using a one dimensional dispersion model. The results indicate higher mean transport velocities and smaller dispersion for deuterium in all experiments. Due to different molecule properties that also determine the interaction of soil substrate and tracer, deuterium indicates a more conservative transport behaviour. Deuterium is non-toxic, completely soluble, chemically and biologically stable and not subject to light-influenced decay. Furthermore, it shows promise for investigations of water flow in the unsaturated zone, and of interactions of water in soil-plant-atmosphere systems. A further discussion of problems, together with possibilities for applying deuterium as an artificial tracer, will be presented.

Deuterium trapping in tungsten deposition layers formed by deuterium plasma sputtering

International Nuclear Information System (INIS)

Alimov, V.Kh.; Roth, J.; Shu, W.M.; Komarov, D.A.; Isobe, K.; Yamanishi, T.

2010-01-01

A study of the influence of the deposition conditions on the surface morphology and deuterium (D) concentration in tungsten (W) deposition layers formed by magnetron sputtering and in the linear plasma generator has been carried out. Thick W layers (≥0.4 μm) deposited onto copper substrates demonstrate areas of pilling and, after post-deposition heating to 1300 K, flaking-off and fracturing. For thin W layers (≤80 nm) deposited onto stainless steel (SS) and W substrates, no areas of flaking-off and fracturing exist both after deposition and after post-deposition heating to 673 K for the SS substrate and to 1300 K for the W substrate. The concentration of deuterium in the W layers was found to decrease with increasing substrate temperature and with increasing tungsten deposition rate. For layers with relatively high concentration of oxygen (0.20-0.60 O/W), a decrease of the D concentration with increasing substrate temperature is more pronounced than that for layers deposited in good vacuum conditions. To describe the evolution of the D/W ratio with the substrate temperature and the tungsten deposition rate, an empirical equation proposed by De Temmerman and Doerner [J. Nucl. Mater. 389 (2009) 479] but with alternative parameters has been used.

Trapping of deuterium dissolved in fluidized Li by Y

Energy Technology Data Exchange (ETDEWEB)

Fukada, Satoshi, E-mail: sfukada@nucl.kyushu-u.ac.jp [Kyushu University, Fukuoka 816-8580 (Japan); Hiromoto, Tetsushi; Shigeharu, Satoshi; Sugie, Kunihiro [Kyushu University, Fukuoka 816-8580 (Japan); Edao, Yuki [Japan Atomic Energy Agency, Tokai 319-1195 (Japan)

2014-10-15

Highlights: • Recovery of deuterium is experimentally proved in liquid Li forced convection flow by Y metal trap. • 10 ppm D as the target concentration is successfully removed from Li flow. • H{sub 2}O or HNO{sub 3} dissolution technique is developed to analyze D concentration in Li or Y. - Abstract: Recovery of D dissolved in a liquid Li flow at low D concentration is experimentally investigated using a Y metal absorber under the two fluidized conditions: (a) in a vertical cylindrical tube and (b) in an agitated vessel. The target concentration is 1 appm in Li around at 300 °C. The two concentrations of D remaining in Li and recovered by Y are detected by a dissolution method using H{sub 2}O with depleted-D and HNO{sub 3}. The main released species is HD. A small amount of HDO released is reduced to HD by a Mg particle bed. It is found that HF-treated Y can absorb H isotopes at the target temperature and concentration. The chemical dissolution technique is found to be useful to specify the two absolute concentrations of D recovered by Y and D remaining in Li.

Trapping of deuterium dissolved in fluidized Li by Y

International Nuclear Information System (INIS)

Fukada, Satoshi; Hiromoto, Tetsushi; Shigeharu, Satoshi; Sugie, Kunihiro; Edao, Yuki

2014-01-01

Highlights: • Recovery of deuterium is experimentally proved in liquid Li forced convection flow by Y metal trap. • 10 ppm D as the target concentration is successfully removed from Li flow. • H 2 O or HNO 3 dissolution technique is developed to analyze D concentration in Li or Y. - Abstract: Recovery of D dissolved in a liquid Li flow at low D concentration is experimentally investigated using a Y metal absorber under the two fluidized conditions: (a) in a vertical cylindrical tube and (b) in an agitated vessel. The target concentration is 1 appm in Li around at 300 °C. The two concentrations of D remaining in Li and recovered by Y are detected by a dissolution method using H 2 O with depleted-D and HNO 3 . The main released species is HD. A small amount of HDO released is reduced to HD by a Mg particle bed. It is found that HF-treated Y can absorb H isotopes at the target temperature and concentration. The chemical dissolution technique is found to be useful to specify the two absolute concentrations of D recovered by Y and D remaining in Li

Structural transformations in austenitic stainless steel induced by deuterium implantation: irradiation at 100 K.

Science.gov (United States)

Morozov, Oleksandr; Zhurba, Volodymyr; Neklyudov, Ivan; Mats, Oleksandr; Rud, Aleksandr; Chernyak, Nikolay; Progolaieva, Viktoria

2015-01-01

Deuterium thermal desorption spectra were investigated on the samples of austenitic stainless steel 18Cr10NiTi preimplanted at 100 K with deuterium ions in the dose range from 3 × 10(15) to 5 × 10(18) D/cm(2). The kinetics of structural transformation development in the implantation steel layer was traced from deuterium thermodesorption spectra as a function of implanted deuterium concentration. At saturation of austenitic stainless steel 18Cr10NiTi with deuterium by means of ion implantation, structural-phase changes take place, depending on the dose of implanted deuterium. The maximum attainable concentration of deuterium in steel is C = 1 (at.D/at.met. = 1/1). The increase in the implanted dose of deuterium is accompanied by the increase in the retained deuterium content, and as soon as the deuterium concentration attains C ≈ 0.5 the process of shear martensitic structural transformation in steel takes place. It includes the formation of bands, body-centered cubic (bcc) crystal structure, and the ferromagnetic phase. Upon reaching the deuterium concentration C > 0.5, the presence of these molecules causes shear martensitic structural transformations in the steel, which include the formation of characteristic bands, bcc crystal structure, and the ferromagnetic phase. At C ≥ 0.5, two hydride phases are formed in the steel, the decay temperatures of which are 240 and 275 K. The hydride phases are formed in the bcc structure resulting from the martensitic structural transformation in steel.

Quantitative analysis of deuterium by gas chromatography

International Nuclear Information System (INIS)

Isomura, Shohei; Kaetsu, Hayato

1981-01-01

An analytical method for the determination of deuterium concentration in water and hydrogen gas by gas chromatography is described. HD and D 2 in a hydrogen gas sample were separated from H 2 by a column packed with Molecular Sieve 13X, using extra pure hydrogen gas as carrier. A thermal conductivity detector was used. Concentrations of deuterium were determined by comparison with standard samples. The error inherent to the present method was less a 1% on the basis of the calibration curves obtained with the standard samples. The average time required for the analysis was about 3 minutes. (author)

Differentiating the role of lithium and oxygen in retaining deuterium on lithiated graphite plasma-facing components

Energy Technology Data Exchange (ETDEWEB)

Taylor, C. N. [Fusion Safety Program, Idaho National Laboratory, P.O. Box 1625-7113, Idaho Falls, Idaho 83415 (United States); School of Nuclear Engineering, Purdue University, 400 Central Drive, West Lafayette, Indiana 47907 (United States); Allain, J. P. [School of Nuclear Engineering, Purdue University, 400 Central Drive, West Lafayette, Indiana 47907 (United States); Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, Illinois 61801 (United States); Luitjohan, K. E. [School of Nuclear Engineering, Purdue University, 400 Central Drive, West Lafayette, Indiana 47907 (United States); Krstic, P. S. [Institute for Advanced Computational Science, Stony Brook University, New York 11794 (United States); Department of Physics and Astronomy, University of Tennessee, Knoxville, Tennessee 37996 (United States); TheoretiK, Knoxville, Tennessee 379XX (United States); Dadras, J. [Department of Physics and Astronomy, University of Tennessee, Knoxville, Tennessee 37996 (United States); Department of Chemistry and Biochemistry, University of California Los Angeles, Los Angeles, California 90095 (United States); Skinner, C. H. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)

2014-05-15

Laboratory experiments have been used to investigate the fundamental interactions responsible for deuterium retention in lithiated graphite. Oxygen was found to be present and play a key role in experiments that simulated NSTX lithium conditioning, where the atomic surface concentration can increase to >40% when deuterium retention chemistry is observed. Quantum-classical molecular dynamic simulations elucidated this oxygen-deuterium effect and showed that oxygen retains significantly more deuterium than lithium in a simulated matrix with 20% lithium, 20% oxygen, and 60% carbon. Simulations further show that deuterium retention is even higher when lithium is removed from the matrix. Experiments artificially increased the oxygen content in graphite to ∼16% and then bombarded with deuterium. X-ray photoelectron spectroscopy showed depletion of the oxygen and no enhanced deuterium retention, thus demonstrating that lithium is essential in retaining the oxygen that thereby retains deuterium.

Standards for deuterium analysis requirements of heavy water plants (Preprint No. CA-1)

Energy Technology Data Exchange (ETDEWEB)

Rathi, B N; Gopalakrishnan, V T; Alphonse, K P; Pawar, P L; Sadhukhan, H K [Bhabha Atomic Research Centre, Bombay (India). Heavy Water Div.

1989-04-01

Accurate analysis of deuterium, covering the entire range, is of great importance in production of heavy water. Most of the methods for determination of deuterium in gas or liquid samples require appropriate standards. Since density of pure protium oxide and pure deuterium oxide has been determined very accurately by a large number of workers and density of mixtures of H{sub 2}O and D{sub 2}O follows a linear relation, it is possible to use accurate density determination for measurement of deuterium content. Float method for density measurements was improved further and used for the preparation of primary heavy water standards in high and low deuterium ranges. Heavy water plant laboratories require gas standards (ammonia synthesis gas matrix), in addition to low deuterium water standards, for calibration of mass spectrometers. SLAP (Standard Light Antarctic Precipitation, D/D+H = 89.02+-0.05ppm) and SMOW (Standard Mean Ocean Water, D/D+H =155.76+-0.05ppm) available from IAEA, Vienna, along with water practically free from deuterium, were used as standards to prepare secondary liquid standards. These secondary standards were subsequently reduced and mixed with pure nitrogen to obtain D/D+H standards in syngas matrix. (author). 8 refs., 2 figs.

Monte Carlo calculations of thermodynamic properties of deuterium under high pressures

International Nuclear Information System (INIS)

Levashov, P R; Filinov, V S; BoTan, A; Fortov, V E; Bonitz, M

2008-01-01

Two different numerical approaches have been applied for calculations of shock Hugoniots and compression isentrope of deuterium: direct path integral Monte Carlo and reactive Monte Carlo. The results show good agreement between two methods at intermediate pressure which is an indication of correct accounting of dissociation effects in the direct path integral Monte Carlo method. Experimental data on both shock and quasi-isentropic compression of deuterium are well described by calculations. Thus dissociation of deuterium molecules in these experiments together with interparticle interaction play significant role

Use of deuterium labelled glucose in evaluating the pathway of hepatic glycogen synthesis

International Nuclear Information System (INIS)

Goodman, M.N.; Masuoka, L.K.; deRopp, J.S.; Jones, A.D.

1989-01-01

Deuterium labelled glucose has been used to study the pathway of hepatic glycogen synthesis during the fasted-refed transition in rats. Deuterium enrichment of liver glycogen was determined using nuclear magnetic resonance as well as mass spectroscopy. Sixty minutes after oral administration of deuterated glucose to fasted rats, the portal vein blood was fully enriched with deuterated glucose. Despite this, less than half of the glucose molecules incorporated into liver glycogen contained deuterium. The loss of deuterium label from glucose is consistent with hepatic glycogen synthesis by an indirect pathway requiring prior metabolism of glucose. The use of deuterium labelled glucose may prove to be a useful probe to study hepatic glycogen metabolism. Its use may also find application in the study of liver glycogen metabolism in humans by a noninvasive means

Deuterium inventory in tungsten after plasma exposure. A microstructural survey

International Nuclear Information System (INIS)

Manhard, Armin

2012-09-01

Tungsten is a promising material for armouring the plasma-facing wall of future nuclear fusion experiments and power plants. It has a very high melting point, good thermal conductivity and is highly resistant against physical sputtering by energetic particles from the plasma. It also has a very low solubility for hydrogen isotopes. This is important both for safety and also for economic reasons, in particular with regard to the radioactive fusion fuel tritium. Due to this low solubility, the retention of hydrogen isotopes in tungsten materials after exposure to a plasma is dominated by the trapping of hydrogen isotopes at tungsten lattice defects. Therefore, a strong dependence of the hydrogen isotope retention on the microstructure of the tungsten is to be expected. This work describes a survey study of tungsten with different microstructures exposed to deuterium plasmas under a wide range of different plasma exposure conditions. The isotope deuterium was used because its natural abundance is much smaller than that of hydrogen (i.e., 1 H). This allows detecting even very small amounts retained in the tungsten practically without background signal. Furthermore, the use of deuterium allows utilising the nuclear reaction 2 D( 3 He,p) 4 He for depth-resolved quantification of the deuterium inventory up to depths of several microns. In order to standardise the specimens as far as possible, they were all cut from the same initial material from a single manufacturing batch. After a chemo-mechanical polishing procedure, which produces a well-defined surface, the specimens were annealed at either of four different temperatures in order to modify the grain structure and the dislocation density. These were then characterised by scanning electron microscopy and scanning transmission electron microscopy. The specimens were subsequently exposed in a fully characterised deuterium plasma source at different specimen temperatures, ion energies and deuterium fluences. In addition

Production of solid deuterium targets by ion implantation

International Nuclear Information System (INIS)

Csikai, J.; Szegedi, S.; Olah, L.; El-Megrab, A.M.; Molla, N.I.; Rahman, M.M.; Miah, R.U.; Habbani, F.; Shaddad, I.

1997-01-01

Solid metal, semiconductor and metallic glass samples were irradiated with deuteron atomic ions between 60 and 180 keV incident energies. Accumulation rates of deuterons in different targets were recorded by the detection of protons and neutrons via the 2 H(d,p) and 2 H(d,n) reactions. A simple analytical expression is given to describe the kinetics of the accumulation. The dependence of the reaction rate on the deuteron energy gives information on the concentration profile in addition to the neutron flux density spectra. A varying distortion of the implanted deuteron profiles by a change in the beam energy were also observed for different targets. (orig.)

Residual stress in deuterium implanted nominal copper coatings

International Nuclear Information System (INIS)

Inal, M. Y.; Alam, M.; Peascoe, R. A.; Watkins, T. R.

2000-01-01

The effects of deuterium (D) implantation on the residual stresses in Cu and CuAl 2 phases present in nominal Cu coatings (containing Al) deposited on Al-alloy (Al-6061) substrates were measured using an x-ray diffraction technique. The coatings were deposited by radio frequency magnetron sputtering of a pure Cu target under identical conditions and Al was incorporated in the coatings during growth by diffusion from the substrate. Deuterium was implanted in the coatings at energies of 40 or 40+120 keV with fluences of 1x10 21 , 2x10 21 , or 3x10 21 D + /m 2 . Pole figures of the Cu phase in the coatings prior to and after implantation indicated no effect of implantation on the fibrous texture. Triaxial stress analysis indicated the surface normal stress component to be negligible in Cu and slightly tensile in CuAl 2 under all conditions. Furthermore, under all conditions, the in-plane residual stresses in both phases were found to be compressive and nearly isotropic. The magnitude of the isotropic compressive stress was always higher in CuAl 2 as compared to Cu. The compressive residual stresses in the Cu phase changed only mildly with increasing coating weight, ion energy, and fluence. However, in the CuAl 2 phase the compressive residual stresses changed markedly with increasing ion energy (initial decrease followed by leveling off) and increasing ion fluence (initial decrease followed by an increase), but remained unaffected by increasing coating weight. (c) 2000 American Institute of Physics

Simulation for Synthesis of Tritiated Styrene by Catalyzed Addition of Deuterium

Directory of Open Access Journals (Sweden)

CUI Xiao-jing;KANG Yi;HU Shi-lin

2016-08-01

Full Text Available Tritiated styrene plays an important role in the organic tritium lights, which could be made by selective hydrogenation of phenylacetylene. A simulated reaction of the preparation of tritiated styrene was studied by using deuterium instead of tritium and using the Lindlar catalyst instead of Pd/C catalyst to improve the conversion and selectivity of the reaction. Experiment results showed that stirring speed, temperature and the amount of deuterium were the most important factors to effect the conversion and selectivity of the reaction. The relative stronger stirring speed and higher temperature could improve the conversion rate of the reaction, but could not change the selectivity. When the excessive or less deuterium was added in the reaction, the selectivity was decreased significantly, since the over deuterium promoted the reaction toward ethylbenzene. Lindlar catalyst exhibited higher selectivity toward styrene than Pd/C.

D₂ and DT Liquid-Layer Target Shots on NIF

Energy Technology Data Exchange (ETDEWEB)

Walters, Curtis [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alger, Ethan [General Atomics, San Diego, CA (United States); Bhandarkar, Suhas [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Boehm, Kurt [General Atomics, San Diego, CA (United States); Braun, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Espinosaloza, Francisco [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haid, Benjamin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heredia, Ricardo [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kline, John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kozioziemski, Bernard [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kroll, Jeremy [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Malone, Daniel [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Nikroo, Abbas [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Opsahl, Patrick [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sater, James [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zylstra, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-22

Experiments at the National Ignition Facility (NIF) using targets containing a Deuterium-Tritium (DT) fuel layer have, until recently, required that a high-quality layer of solid deuterium-tritium (herein referred to as an "ice-layer") be formed in the capsule. The development of a process to line the inner surface of a target capsule with a foam layer of a thickness that is typical of icelayers has resulted in the ability to field targets with liquid layers wetting the foam. Successful fielding of liquid-layer targets on NIF required not only a foam lined capsule, but also changes to the capsule filling process and the manner with which the inventory is maintained in the capsule. Additionally, changes to target heater power and the temperature drops across target components were required in order to achieve the desired range of shot temperatures. These changes, and the target's performance during four target shots on NIF will be discussed.

Deuterium Excess of Waters in Slovenia. Preliminary Results

Energy Technology Data Exchange (ETDEWEB)

Brencic, M.; Torkar, A. [Faculty of Natural Sciences and Engineering, University of Ljubljana, Ljubljana (Slovenia); Vreca, P. [Jozef Stefan Institut, Department of Environmental Sciences, Ljubljana (Slovenia)

2013-07-15

In climatic and hydrological studies, deuterium excess has proven to be a useful parameter; therefore this parameter has been investigated in the waters of slovenia - positioned in central europe. All the data were acquired from publicly available data sources (e.g. journals, databases). Data were collected for four different parts of the water cycle: precipitation, surface water, groundwater and water in the unsaturated zone. For precipitation the value for deuterium excess ranges between -19.9 per mille and 28.8 per mille with the median at 10.1 per mille. Surface water has the minimum at 2.9 per mille, the maximum at 22.4 per mille and the median at 13.2 per mille. Values for groundwater vary between -17.7 per mille and 34.9 per mille with the median at 11.8 per mille. Median for deuterium excess for the unsaturated zone is 15.1 per mille and the values are between -2.8 per mille and 17.6 per mille. (author)

Molecular deuterium behaviour in tungsten divertor on JET

Energy Technology Data Exchange (ETDEWEB)

Sergienko, G., E-mail: g.sergienko@fz-juelich.de [Institute of Energy and Climate Research –Plasma Physics, Forschungszentrum Jülich, EURATOM Association, Trilateral Euregio Cluster, D-52425 Jülich (Germany); Arnoux, G. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Brezinsek, S.; Clever, M.; Huber, A.; Kruezi, U. [Institute of Energy and Climate Research –Plasma Physics, Forschungszentrum Jülich, EURATOM Association, Trilateral Euregio Cluster, D-52425 Jülich (Germany); Meigs, A.G. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Mertens, Ph.; Samm, U. [Institute of Energy and Climate Research –Plasma Physics, Forschungszentrum Jülich, EURATOM Association, Trilateral Euregio Cluster, D-52425 Jülich (Germany); Stamp, M. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)

2013-07-15

Molecular spectroscopy was used to observe molecular deuterium at the outer strike point of the new bulk tungsten JET divertor. The rotational and vibrational populations of the deuterium molecules in the ground state were determined from the deuterium Q-branches of Fulcher-α band emission (d{sup 3}Π{sub u}{sup -}→a{sup 3}Σ{sub g}{sup +}) in the 600–640 nm spectral range. For L-mode plasmas in the low recycling regime the molecular emission maximum is located in the vicinity of the strike point. The spatial profile of the emission was strongly modified during plasma detachment in both L- and H-mode plasmas. The rotational temperature of excited molecules reached 2760 K in L-mode. The vibrational population has a peculiarity: a remarkably high population of the d{sup 3}Π{sub u}{sup -}(v = 0) vibrational level indicating a non-Boltzmann vibrational distribution of D{sub 2} in tungsten environment.

TFTR L mode energy confinement related to deuterium influx

International Nuclear Information System (INIS)

Strachan, J.D.

1999-01-01

Tokamak energy confinement scaling in TFTR L mode and supershot regimes is discussed. The main result is that TFTR L mode plasmas fit the supershot scaling law for energy confinement. In both regimes, plasma transport coefficients increased with increased edge deuterium influx. The common L mode confinement scaling law on TFTR is also inversely proportional to the volume of wall material that is heated to a high temperature, possibly the temperature at which the deuterium sorbed in the material becomes detrapped and highly mobile. The deuterium influx is increased by: (a) increased beam power due to a deeper heated depth in the edge components and (b) decreased plasma current due to an increased wetted area as governed by the empirically observed dependence of the SOL width upon plasma current. (author). Letter-to-the-editor

The effect of charge exchange with neutral deuterium on carbon emission in JET divertor plasmas

International Nuclear Information System (INIS)

Maggi, C.; Horton, L.; Summers, H.

1999-11-01

High density, low temperature divertor plasma operation in tokamaks results in large neutral deuterium concentrations in the divertor volume. In these conditions, low energy charge transfer reactions between neutral deuterium and the impurity ions can in principle enhance the impurity radiative losses and thus help to reduce the maximum heat load to the divertor target. A quantitative study of the effect of charge exchange on carbon emission is presented, applied to the JET divertor. Total and state selective effective charge exchange recombination rate coefficients were calculated in the collisional radiative picture. These coefficients were coupled to divertor and impurity transport models to study the effect of charge exchange on the measured carbon spectral emission in JET divertor discharges. The sensitivity of the effect of charge exchange to the assumptions in the impurity transport model was also investigated. A reassessment was made of fundamental charge exchange cross section data in support of this study. (author)

Initial deuterium pellet experiments on FTU

International Nuclear Information System (INIS)

Snipes, J.A.

1993-01-01

Initial experiments have been performed with the Single Pellet INjector (SPIN) on FTU. SPIN is a two-stage cryogenic deuterium pellet injector capable of injection,a pellets with velocities up to 2.5 km/s. The nominal pellet mass for these experiments was approximately 1 x 10 20 atoms. These initial pellet experiments concentrated on studying pellet penetration under a variety of plasma conditions to compare with code predictions and to examine toroidal particle transport. The principal diagnostics used were two fast (∼1 μsec) photomultiplier tubes at nearly opposite toroidal locations with H α (D α ) interference filters (λ = 656 nm), a microwave cavity for pellet mass and velocity, a vertical array of soft x ray diodes without filters looking down onto the pellet, a DCN interferometer for electron density profiles, and a Michelson ECE system for electron temperature profiles. The time integral of the absolutely calibrated fast H α signal appears to give reasonable agreement with the expected pellet mass. Toroidal transport of deuterium ions from the pellet to nearly the opposite side of the tokamak agrees with calculated thermal deuterium velocities near the plasma edge. Comparison of the experimental results with code calculations using the Neutral Gas Shielding model show good agreement for the post-pellet electron temperature and density profiles and the H α profiles in some cases. Calculated penetration distances agree within 20%

Reemission and permeation of deuterium implanted into metals

International Nuclear Information System (INIS)

Tanabe, T.; Furuyama, Y.; Imoto, S.

1984-01-01

Focusing on the marked depression of deuterium permeation rate during the deuteron bombardment, implantation experiments coupled with gaseous permeation experiments are performed on pure Ni and Ni with evaporated MnO. It is concluded that the reemission of implanted deuterium is initially depressed, but it soon becomes enhanced with increase of fluence leading to a rapid decrease of permeation rate at the intermediate temperatures 600-1000 K, which is attributed to the formation of short diffusion paths from the projected range to the front surface. (orig.)

Deuterium absorption and material phase characteristics of Zr2Fe

International Nuclear Information System (INIS)

Nobile, A.; Mosley, W.C.; Holder, J.S.; Brooks, K.N.

1992-01-01

Scanning electron microscope (SEM) images of polished surfaces, electron probe microanalysis, and X-ray powder diffractometry indicated the presence of a continuous Zr 2 Fe phase with secondary phases of ZrFe 2 , Zr 5 FeSn, α-Zr, and Zr 6 Fe 3 O. A statistically-designed experiment to determine the effects of temperature, time, and vacuum quality On activation of St 198 revealed that when activated at low temperature (350 degrees C) deuterium absorption rate was slower when the vacuum quality was pwr (2.5 Pa vs. 3x10 -4 Pa). However, at higher activation temperature (500 degrees C), deuterium absorption rate was fast and was independent of vacuum quality. Deuterium pressure-composition-temperature (P-C-T) data are reported for St 198 in the temperature range 200--500 degrees C. The P-C-T data over the full range of deuterium loading and at temperatures of 350 degrees C and below is described by: K 0e -(ΔH α /RT)=PD 2 q 2 /(q*-q) 2 where ΔHα and K 0 have values of 101.8 kJ·mole -1 and 3.24x10 -8 Pa -1 , and q* is 15.998 kPa·L -1 ·g -1 . At higher temperatures, one or more secondary reactions in the solid phase occur that slowly consume D 2 from the gas phase. XRD suggests these reactions to be: 2 Zr 2 FeD x → x ZrD 2 + x/3 ZrFe 2 + (2 - 2/3x) Zr 2 Fe and Zr 2 FeD x + (2 -1/2x) D 2 → ZrD 2 + Fe, where 0 < x < 3. Reaction between gas phase deuterium and Zr2FC formed in the first reaction accounts for the observed consumption of deuterium from the gas phase by this reaction

DeUterium industrial production - tome 8

International Nuclear Information System (INIS)

Chagas, T.P.

1987-01-01

Some selected bibliographical references about processes for deuterium industrial production are presented, as follow: isotope exchange H 2 S-H 2 O and NH 3 -H 2 , eletrolysis and distillation. (E.G.) [pt

Permeation of deuterium implanted into V-15Cr-5Ti

International Nuclear Information System (INIS)

Anderl, R.A.; Longhurst, G.R.; Struttmann, D.A.

1987-01-01

Permeation and reemission of deuterium for the vanadium alloy, V-15Cr-5Ti, was investigated using 3 keV, D 3 + ion beams from a small accelerator. The experiments consisted of measurement of the deuterium reemission and permeation rates as a function of implantation fluence for 0.5 mm thick specimens heated to temperatures from 623 K to 823 K. Implantation-side surface characterization was made by simultaneous measurements of sputtered ions with a secondary ion mass spectrometer (SIMS). For the experimental conditions used, the steady-state deuterium permeation flux in V-15Cr-5Ti is approximately 18% of the implantation flux. This is approximately 1000 times that seen in the austenitic stainless steel, PCA, and 200 times that seen in the ferritic steel, HT-9, under comparable conditions. Measurement of deuterium diffusivity in V-15Cr-5Ti using permeation break-through times indicates that D = 1.4x10 -8 exp(-0.11 eV/kT)(m 2 /s), over the temperature range 723 K to 823 K. (orig.)

Permeation of deuterium implanted into V-15Cr-5Ti

Science.gov (United States)

Anderl, R. A.; Longhurst, G. R.; Struttmann, D. A.

1987-02-01

Permeation and reemission of deuterium for the vanadium alloy, V-15Cr-5Ti, was investigated using 3 keV, D 3+ ion beams from a small accelerator. The experiments consisted of measurement of the deuterium reemission and permeation rates as a function of implantation fluence for 0.5 mm thick specimens heated to temperatures from 623 K to 823 K. Implantation-side surface characterization was made by simultaneous measurements of sputtered ions with a secondary ion mass spectrometer (SIMS). For the experimental conditions used, the steady-state deuterium permeation flux in V-15Cr-5Ti is approximately 18% of the implantation flux. This is approximately 1000 times that seen in the austenitic stainless steel, PCA, and 200 times that seen in the ferritic steel, HT-9, under comparable conditions. Measurement of deuterium diffusivity in V-15Cr-5Ti using permeation break-through times indicates that D = 1.4 × 10 -8 exp( -0.11 eV/ kT) (m 2/s), over the temperature range 723 K to 823 K.

Permeation of deuterium implanted into V-15Cr-5Ti

Energy Technology Data Exchange (ETDEWEB)

Anderl, R.A.; Longhurst, G.R.; Struttmann, D.A.

1987-02-01

Permeation and reemission of deuterium for the vanadium alloy, V-15Cr-5Ti, was investigated using 3 keV, D/sub 3//sup +/ ion beams from a small accelerator. The experiments consisted of measurement of the deuterium reemission and permeation rates as a function of implantation fluence for 0.5 mm thick specimens heated to temperatures from 623 K to 823 K. Implantation-side surface characterization was made by simultaneous measurements of sputtered ions with a secondary ion mass spectrometer (SIMS). For the experimental conditions used, the steady-state deuterium permeation flux in V-15Cr-5Ti is approximately 18% of the implantation flux. This is approximately 1000 times that seen in the austenitic stainless steel, PCA, and 200 times that seen in the ferritic steel, HT-9, under comparable conditions. Measurement of deuterium diffusivity in V-15Cr-5Ti using permeation break-through times indicates that D = 1.4x10/sup -8/ exp(-0.11 eVkT)(m/sup 2/s), over the temperature range 723 K to 823 K.

Deuterium labeled cannabinoids

International Nuclear Information System (INIS)

Driessen, R.A.

1979-01-01

Complex reactions involving ring opening, ring closure and rearrangements hamper complete understanding of the fragmentation processes in the mass spectrometric fragmentation patterns of cannabinoids. Specifically labelled compounds are very powerful tools for obtaining more insight into fragmentation mechanisms and ion structures and therefore the synthesis of specifically deuterated cannabinoids was undertaken. For this, it was necessary to investigate the preparation of cannabinoids, appropriately functionalized for specific introduction of deuterium atom labels. The results of mass spectrometry with these labelled cannabinoids are described. (Auth.)

Evidence of emission of neutrons from a titanium-deuterium system

International Nuclear Information System (INIS)

Ninno, A. de; Frattolillo, A.; Lollobattista, G.; Martinis, L.; Martone, M.; Mori, L.; Podda, S.; Scaramuzzi, F.

1989-01-01

The interaction of deuterium gas with titanium has produced a flow of neutrons in two experiments reported here. This seems to show that it is not necessary to use electrolysis in order to obtain a low-temperature fusion reaction between deuterium nuclei. The experiment confirms also that nonequilibrium conditions are necessary in order to produce such a phenomenon

Deuterium permeation of amorphous alumina coating on 316L prepared by MOCVD

International Nuclear Information System (INIS)

Li Shuai; He Di; Liu Xiaopeng; Wang Shumao; Jiang Lijun

2012-01-01

Highlights: ► Deuterium permeation behavior of alumina coating by MOCVD is investigated. ► The as-prepared alumina is amorphous. ► The alumina coating is dense and well adherent to substrate. ► Deuterium permeation rate of alumina coating is 2–3 orders of magnitude lower than martensitic steels. - Abstract: The deuterium permeation behavior of the alumina coating on 316L stainless steel prepared by metal organic chemical vapor deposition (MOCVD) was investigated. The alumina coating was also characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscope (SEM). It was found that the as-prepared coating consisted of amorphous alumina. This alumina coating had a dense, crack-free and homogeneous morphology. Although the alumina coating was amorphous, effective suppression of deuterium permeation was demonstrated. The deuterium permeability of the alumina coating was 51–60 times less than that of the 316L stainless steel and 153–335 times less than that of the referred low activation martensitic steels at 860–960 K.

Process for the production of hydrogen/deuterium-containing gas

International Nuclear Information System (INIS)

Nitschke, E.; Desai, A.; Ilgner, H.

1978-01-01

A process for the production of hydrogen/deuterium-containing gas is described in which the enriched condensate obtained from the production of a hydrogen/deuterium-containing gas mixture is collected and subjected to a direct exchange of isotopes with the feedsteam admitted to the process. Such condensate can be brought into direct exchange of isotopes with the gas water vapor mixture within the process, viz. ahead of the CO conversion section. The exchange of isotopes may be performed according to the counter-current principle. If it is intended to maintain in the hydrogen/deuterium-containing gas a certain definite content of water vapor whose phase condition is superior to the condition achieved when using normal cooling water, this gas, at least 0.6 kg/m 3 of gas, is subjected to an exchange of isotopes with the water fed additionally into the process

Commissioning status of the Continuous Wave Deuterium Demonstrator

International Nuclear Information System (INIS)

Hartog, P.D.; Dooling, J.; Lorello, M.; Rathke, J.; Carwardine, J.; Godden, D.; Pile, G.; Yule, T.; Zinneman, T.

1993-01-01

Grumman Aerospace Corporation, Argonne National Laboratory, and Culham Laboratory are commissioning the Continuous Wave Deuterium Demonstrator (CWDD) in a facility at Argonne National Laboratory. CWDD is a high-brightness, high-current, 7.5-MeV negative deuterium accelerator. The 352-MHz rf accelerating cavities are cryogenically cooled with supercritical neon to reduce the rf power requirements. Installation of the accelerator into the Argonne facility began in May 1991, and first beam from the injector was extracted in February 1992. The accelerator and facility and described, and current status and future plans are discussed

Deuterium sputtering of Li and Li-O films

Science.gov (United States)

Nelson, Andrew; Buzi, Luxherta; Kaita, Robert; Koel, Bruce

2017-10-01

Lithium wall coatings have been shown to enhance the operational plasma performance of many fusion devices, including NSTX and other tokamaks, by reducing the global wall recycling coefficient. However, pure lithium surfaces are extremely difficult to maintain in experimental fusion devices due to both inevitable oxidation and codeposition from sputtering of hot plasma facing components. Sputtering of thin lithium and lithium oxide films on a molybdenum target by energetic deuterium ion bombardment was studied in laboratory experiments conducted in a surface science apparatus. A Colutron ion source was used to produce a monoenergetic, mass-selected ion beam. Measurements were made under ultrahigh vacuum conditions as a function of surface temperature (90-520 K) using x-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and temperature programmed desorption (TPD). Results are compared with computer simulations conducted on a temperature-dependent data-calibrated (TRIM) model.

Comparative study of heavy and deuterium-depleted water on platelet aggregation

International Nuclear Information System (INIS)

Haulica, I.; Neagu, B.; Boisteanu, C.P.; Bild, W.; Mihaila, C.; Bajenariu, M.

2000-01-01

The effects of timed incubation of PRP (Platelet-Rich Plasma) with various concentrations of deuterium-depleted or deuterated water were tested. Aggregation curves were obtained under constant stirring at 20 deg.C and at 37 deg.C, using 5 - 10 μM ADP as aggregation trigger, using a Specord photo colorimeter. Incubation with 10 % deuterated water showed a significant decrease in the aggregation curves, an effect consistent with the data in the literature. Incubation with deuterium depleted water in the same conditions showed a marked increase in the aggregation curves, which suggests a powerful pro-aggregating effect of deuterium depleted water. (authors)

Synthesis of regio- and stereospecifically deuterium labelled 2-benzylindanes

International Nuclear Information System (INIS)

Kuck, D.

1984-01-01

2-Benzylindenes (1, 1a) are hydrogenated to 2-benzylindanes (2) using tris-(triphenylphosphine)-rhodium(I)-chloride in benzene by a strict cis-1,2 addition of hydrogen to the double bond. Thus, stereo- and regio-specific deuterium labelling at the five-membered ring of various 2-benzylindanes has been carried out. The high selectivity of deuterium incorporation is shown independently by 1 H NMR and mass (MIKEsup(*)) spectrometry of selected 2-benzylindanes. (orig.)

Determination of deuterium in metal by vacuum fusion-mass spectrometric method

International Nuclear Information System (INIS)

Wada, Yukio; Akiyama, Shigeo; Ochiai, Ken-ichi; Asakura, Toshiro; Tsutsumi, Ken-ichi

1976-01-01

A specimen of deuterium-enriched Zircaloy was prepared to study a method for the determination of deuterium in metal. The measuring apparatus consists of vacuum fusion section (10 -5 -10 -4 Torr), gas extracting and collecting section, the section of introducing both standard D 2 and HD gases into a gas holder, and mass spectrometric analysis section. The deuterium in Zircaloy can be extracted by 100% for 5 min. at 1600 0 C. The main components of the extracted gas are H 2 , D 2 , HD, CO, H 2 O and N 2 . Deuterium is determined by the calculation from the determinations of D 2 and HD. The amounts of D 2 and HD gases in the specimen were obtained from the calibration curve prepared and the spectrum intensity of D 2 + and HD + resulted from specimen analysis. As a result of the analysis of D 2 -enriched Zircaloy, it has been found that the precision of the determination is within the coefficient variation of about 3% for the extracted D 2 gas amount of 10 -3 -10 -2 ml (STP), including the deuterium segregation in the specimen, and the determination limit was 1 x 10 -5 ml (STP). (Kobatake, H.)

Long life neutron generator target using deuterium pass-through structure

Science.gov (United States)

Alger, D. L.

1974-01-01

Target structure permits all deuterons, except the one-in-a-million that interacts with tritium atom to produce a neutron, to pass completely through target structure and be returned to vacuum system. Since tritium atoms are not displaced as in conventional targets, tritium population will remain unchanged while under deuteron bombardment.

Process and device for stage by stage enrichment of deuterium and/or tritium in a material suitable for isotope exchange of deuterium and tritium with hydrogen

International Nuclear Information System (INIS)

Iniotakis, N.; Decken, C.B. von der.

1983-01-01

Water containing deuterium and/or tritium is first introduced into a carrier gas flow and reduced for the stage by stage enrichment of deuterium and/or tritium. A hydrogen partial pressure of a maximum of 100 millibar is set in the carrier gas flow. The carrier gas flow is taken along the primary side of an exchange wall suitable for the permeation of hydrogen, and a further carrier gas flow flows on its secondary side, which contains water or hydrogen. Reaction products formed after isotope exchange of deuterium and/or tritium with hydrogen are removed by the secondary carrier gas flow. (orig./HP) [de

Depth concentrations of deuterium ions implanted into some pure metals and alloys

International Nuclear Information System (INIS)

Didyk, A.Yu.; Wisniewski, R.; Kitowski, K.; Wilczynska, T.; Hofman, A.; Kulikauskas, V.; Shiryaev, A.A.; Zubavichyus, Ya.V.

2011-01-01

Pure metals (Cu, Ti, Zr, V, Pd) and diluted Pd alloys (Pd-Ag, Pd-Pt, Pd-Ru, Pd-Rh) were implanted by 25-keV deuterium ions at fluences in the range (1.2-2.3) x 10 22 D + /m 2 . The post-treatment depth distributions of deuterium ions were measured 10 days and three months after the implantation by using Elastic Recoil Detection Analysis (ERDA) and Rutherford Backscattering (RBS). Comparison of the obtained results allowed us to make conclusions about relative stability of deuterium and hydrogen gases in pure metals and diluted Pd alloys. Very high diffusion rates of implanted deuterium ions from V and Pd pure metals and Pd alloys were observed. Small-angle X-ray scattering revealed formation of nanosized defects in implanted corundum and titanium

Mass Producing Targets for Nuclear Fusion

Science.gov (United States)

Wang, T. G.; Elleman, D. D.; Kendall, J. M.

1983-01-01

Metal-encapsulating technique advances prospects of controlling nuclear fusion. Prefilled fusion targets form at nozzle as molten metal such as tin flows through outer channel and pressurized deuterium/tritium gas flows through inner channel. Molten metal completely encloses gas charge as it drops off nozzle.

Synthesis of deuterium-labelled diclofenac sodium

International Nuclear Information System (INIS)

Leroy, D.; Richard, J.; Godbillon, J.

1993-01-01

Dicolofenac sodium labelled with deuterium in the phenylacetic ring was prepared from [ 2 H 5 ]-bromobenzene in a six-step reaction. It was found to be suitable for use in pharmacokinetic and bioavailability studies in man. (Author)

Some experiments on cold fusion by deuterium hydrogen gas infusion in titanium metal alloy

International Nuclear Information System (INIS)

Mestnik Filho, J.; Geraldo, L.P.; Pugliese, R.; Saxena, R.N.; Morato, S.P.; Fulfaro, R.

1990-05-01

New results on cold fusion are reported where three different experimental situations have been tried: a) deuterium gas loaded titanium; b) deuterium gas loaded Ti 0.8 Zr 0.2 CrMn alloy and c) titanium and the Ti 0.8 Zr 0.2 CrMn alloy loaded with a mixture of deuterium and hydrogen gases. With these experiments, new thermodynamical non equilibrium conditions were achieved and the possibility of cold fusion between protons and deuterons was also tested. Three independent neutron detectors and one NaI(Tl) were utilized. Despite some large values reported in the literature for the fusion rate, an upper limit of only 8 x 10 -24 fusions/sper deuterium pair or per deuterium-hydrogen pair was determined within the attained accuracy. (author) [pt

Determination of deuterium concentration by falling drop method

International Nuclear Information System (INIS)

Kawai, Hiroshi; Morishima, Hiroshige; Koga, Taeko; Niwa, Takeo; Fujii, Takashi.

1976-01-01

Falling drop method for determination of deuterium concentration in water sample was studied. The principle is the same as that developed by Kirshenbaum, I. in 1932. One drop of water sample falls down through a column filled with o-fluorotoluene at temperature of nearly 25 0 C. The falling time is, instead of using a stop-watch, measured with two light pulses led to a photomultiplier with mirrors, which make two pulse marks on moving chart paper. Distance between the two pulse marks is proportional to falling time. Instead of water filled double chambers of constant temperature equipped with heaters, thermostats and propellers for stirring, the column is dipped in circulating water supplied from a ''Thermoelectric'' made by ''Sharp'' company, which can circulate constant temperature water cooled or heated with thermoelements. Variation of the temperature is about 0.01 0 C. The range of deuterium concentration in our case was 20 -- 60D%. Sensitivity increased as the medium temperature decreased and as deuterium concentration of water sample increased. (auth.)

Double recharge of pions on a deuterium

International Nuclear Information System (INIS)

Nichitiu, F.; Falomkin, I.V.; Shcherbakov, Yu.A.

1987-01-01

Assumptions on the dibaryon nature of the existing narrow resonances below the threshold of the NΔ-state with masses 1935, 1965, 2015 MeV are considered. New proposals on construction of the particle systematics with a new particle (R-particle of mass 1025 MeV, J=1/2, T=3/2) are used to draw a conclusion that double charge exchange is possible on deuterium and helium-3 if dibaryons or new R-particles are born in the final state. Attention is paid to a possible decay of these particles through a weak channel. A search for double charge exchange of pions on hydrogen and deuterium using a laser-illuminated streamer chamber of high pressure is proposed

Use of 60 ppm deuterium depleted water in companionship animals

International Nuclear Information System (INIS)

Balint, Emilia; Manolescu, N.; Cranganu, D.; Militaru, Manuela; Pop, Aneta; Codreanu, M.; Panait, Marieta; Lastofka, D.

2004-01-01

There are presented the results of studies on the effects of deuterium depleted water in companionship animals. Based on these results, a new product was realized, 'Aqua Forte' that is a deuterium depleted potable water (60 ppm deuterium) with beneficial effects in animal's health maintaining. Aqua forte has prophylactic properties (in preventing diseases related to immune system) and therapeutic properties, as adjuvant in various therapeutic programs. The mechanism of action takes place at the cellular metabolism level by replacing the constitutional and free water of 150 ppm deuterium, this resulting in the stimulation of the immune cellular system and also of resistance at the onset of some pathological states. The non-specific stimulation implies performing both the humoral mediated immune reactions and of those cellularly mediated. Aqua forte is recommended in: - the feeding of the young weaned animals, the action being of growth stimulation, and increasing of the resistance against some diseases specific to the age; - as an adjuvant in some chronic diseases (hepatitis, pancreatitis, dermatological diseases, osteoarthropaties, hepato-renal syndrome, renal insufficiency, after surgical interventions, in antitumoral therapy); - in the feeding of the old animals for the quality of life improvement. (authors)

Biotechnological Patents Applications of the Deuterium Oxide in Human Health.

Science.gov (United States)

da S Mariano, Reysla M; Bila, Wendell C; Trindade, Maria Jaciara F; Lamounier, Joel A; Galdino, Alexsandro S

2017-01-01

Deuterium oxide is a molecule that has been used for decades in several studies related to human health. Currently, studies on D2O have mobilized a "Race for Patenting" worldwide. Several patents have been registered from biomedical and technological studies of D2O showing the potential of this stable isotope in industry and health care ecosystems. Most of the patents related to the applications of the deuterium oxide in human health have been summarized in this review. The following patents databases were consulted: European Patent Office (Espacenet), the United States Patent and Trademark Office (USPTO), the United States Latin America Patents (LATIPAT), Patent scope -Search International and National Patent Collections (WIPO), Google Patents and Free Patents Online. With this review, the information was collected on recent publications including 22 patents related to deuterium oxide and its applications in different areas. This review showed that deuterium oxide is a promising component in different areas, including biotechnology, chemistry and medicine. In addition, the knowledge of this compound was covered, reinforcing its importance in the field of biotechnology and human health. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Neutron measurements from beam-target reactions at the ELISE neutral beam test facility

International Nuclear Information System (INIS)

Xufei, X.; Fan, T.; Nocente, M.; Gorini, G.; Bonomo, F.; Franzen, P.; Fröschle, M.; Grosso, G.; Tardocchi, M.; Grünauer, F.; Pasqualotto, R.

2014-01-01

Measurements of 2.5 MeV neutron emission from beam-target reactions performed at the ELISE neutral beam test facility are presented in this paper. The measurements are used to study the penetration of a deuterium beam in a copper dump, based on the observation of the time evolution of the neutron counting rate from beam-target reactions with a liquid scintillation detector. A calculation based on a local mixing model of deuterium deposition in the target up to a concentration of 20% at saturation is used to evaluate the expected neutron yield for comparison with data. The results are of relevance to understand neutron emission associated to beam penetration in a solid target, with applications to diagnostic systems for the SPIDER and MITICA Neutral Beam Injection prototypes

Extraction of deuterium from D-rich process condensate of ammonia plants

Energy Technology Data Exchange (ETDEWEB)

Haldar, T K; Kumar, Manoj; Ramamurty, C B [Heavy Water Board, Department of Atomic Energy, Mumbai (India)

1994-06-01

Heavy water plants based on ammonia-hydrogen exchange process receives feed synthesis gas from the adjacent fertilizer plants. The production capacity of such heavy water plants is directly proportional to the deuterium-content in feed synthesis gas. The chemical process involved in gas generation section of the fertilizer plant includes catalytic steam-reforming of natural gas/naphtha/fuel oil followed by shift conversion, alternatively coal classification followed by shift conversion. Effective extraction of deuterium from the deuterium-rich process condensate can boost the production capacity of heavy water plants considerably. This paper discusses various possible methods to achieve this objective. (author). 5 refs., 1 fig., 1 tab.

Thermally induced outdiffusion studies of deuterium in ceramic breeder blanket materials after irradiation

Energy Technology Data Exchange (ETDEWEB)

González, Maria, E-mail: maria.gonzalez@ciemat.es [LNF-CIEMAT, Materials for Fusion Group, Madrid (Spain); Carella, Elisabetta; Moroño, Alejandro [LNF-CIEMAT, Materials for Fusion Group, Madrid (Spain); Kolb, Matthias H.H.; Knitter, Regina [Karlsruhe Institute of Technology, Institute for Applied Materials (IAM-WPT), Karlsruhe (Germany)

2015-10-15

Highlights: • Surface defects in Lithium-based ceramics are acting as trapping centres for deuterium. • Ionizing radiation affects the deuterium sorption and desorption processes. • By extension, the release of the tritium produced in a fusion breeder will be effective. - Abstract: Based on a KIT–CIEMAT collaboration on the radiation damage effects of light ions sorption/desorption in ceramic breeder materials, candidate materials for the ITER EU TBM were tested for their outgassing behavior as a function of temperature and radiation. Lithium orthosilicate based pebbles with different metatitanate contents and pellets of the individual oxide components were exposed to a deuterium atmosphere at room temperature. Then the thermally induced release of deuterium gas was registered up to 800 °C. This as-received behavior was studied in comparison with that after exposing the deuterium-treated samples to 4 MGy total dose of gamma radiation. The thermal desorption spectra reveal differences in deuterium sorption/desorption behavior depending on the composition and the induced ionizing damage. In these breeder candidates, strong desorption rate at approx. 300 °C takes place, which slightly increases with increasing amount of the titanate second phase. For all studied materials, ionizing radiation induces electronic changes disabling a number of trapping centers for D{sub 2} adsorption.

Body composition of lactating and dry Holstein cows estimated by deuterium dilution

International Nuclear Information System (INIS)

Martin, R.A.; Ehle, F.R.

1986-01-01

In three experiments patterns of water turnover and body composition estimated by deuterium oxide were studied in Holstein cows. In the first experiment, four lactating cows were infused with deuterium oxide, and blood samples were taken during 4-d collection. Milking was stopped; cows were reinfused with deuterium oxide and resampled. Slopes of deuterium oxide dilution curves indicated lactating cows turned water over more rapidly than nonlactating cows. In the second experiment with the same four cows, during 4-d collection, deuterium oxide concentrations in milk, urine, and feces showed dilution patterns similar to deuterium oxide in blood. Sampling milk may be an alternative to sampling blood. In the third experiment, 36 Holstein cows were fed 55, 65, or 75% alfalfa, smooth bromegrass, or equal parts of each forage as total mixed rations; remaining portions of rations were a grain mixture. Body composition was estimated at -1, 1, 2, 3, 4, and 5 mo postpartum. Empty body water, protein, mineral, fat, and fat percentage decreased from prepartum to postpartum. First calf heifers contained less empty body water, protein, and mineral than older cows. Cows fed diets with 55% forage had more body fat than those fed diets with 75% forage. Cows fed alfalfa-based diets had more gastrointestinal fill regardless of grain than cows fed diets that contained alfalfa and smooth bromegrass. Gastrointestinal fill of cows increased from prepartum to 5 mo postpartum

Polarized atomic beams for targets

International Nuclear Information System (INIS)

Grueebler, W.

1984-01-01

The basic principle of the production of polarized atomic hydrogen and deuterium beams are reviewed. The status of the present available polarization, density and intensity are presented. The improvement of atomic beam density by cooling the hydrogen atoms to low velocity is discussed. The possible use of polarized atomic beams as targets in storage rings is shown. It is proposed that polarized atomic beams can be used to produce polarized gas targets with high polarization and greatly improved density

Photodisintegration of deuterium

International Nuclear Information System (INIS)

Hara, K.Y.; Utsunomiya, H.; Goko, S.

2004-01-01

Photodisintegration cross sections were measured for deuterium with Laser Compton scattering γ beams at E γ = 2.3 - 4.6 MeV. The present data made it possible to experimentally evaluate R(E) = N a συ for the p(n, γ)D reaction with 6% uncertainty in the energy region to big bang nucleosynthesis (BBN). The result confirms the past theoretical evaluation and the recent calculation based on the effective field theory. The reaction rate for the p(n, γ)D reaction is presented for the BBN in the precision era. (author)

Deuterium pellet injector gun design

International Nuclear Information System (INIS)

Lunsford, R.V.; Wysor, R.B.; Bryan, W.E.; Shipley, W.D.; Combs, S.K.; Foust, C.R.; Milora, S.L.; Fisher, P.W.

1985-01-01

The Deuterium Pellet Injector (DPI), an eight-pellet pneumatic injector, is being designed and fabricated for the Tokamak Fusion Test Reactor (TFTR). It will accelerate eight pellets, 4 by 4 mm maximum, to greater than 1500 m/s. It utilizes a unique pellet-forming mechanism, a cooled pellet storage wheel, and improved propellant gas scavenging

New developments in cryo-targets for the external COSY experiments

CERN Document Server

Abdel-Samad, S; Kilian, K

2002-01-01

For cooling the liquid hydrogen/deuterium target from room temperature to the operating temperature (15 K/19 K) until recently a long solid copper heat conductor and a short heat pipe was used between cooling machine and the target cell. Recently, a new target version with metallic heat conductor of minimal length and a long gravity-assisted heat pipe section was constructed. The target material is used as a heat transport medium and high heat transfer is achieved by liquid-gas circulation. This design drastically reduces the weight of the system to less than 10 g in the 32 cm long standard geometry as compared with the previous copper heat conductors of 600 g. Uncontrollable secondary interactions are thus avoided. The cycle time of cooling down or heating up is reduced. The characteristics at steady-state operating conditions of the new 32 cm heat pipe-target system have been measured for hydrogen, deuterium, nitrogen and methane as the working fluids. Also successful was the development of a 2 m long heat ...

Preparations for deuterium tritium experiments on the Tokamak Fusion Test Reactor

International Nuclear Information System (INIS)

Hawryluk, R.J.; Adler, H.; Alling, P.; Ancher, C.; Anderson, H.; Anderson, J.W.; Arunasalam, V.; Ascione, G.; Ashcroft, D.; Barnes, G.

1994-04-01

The final hardware modifications for tritium operation have been completed for the Tokamak Fusion Test Reactor (TFTR). These activities include preparation of the tritium gas handling system, installation of additional neutron shielding, conversion of the toroidal field coil cooling system from water to a Fluorinet trademark system, modification of the vacuum system to handle tritium, preparation and testing of the neutral beam system for tritium operation and a final deuterium-deuterium (D-D) run to simulate expected deuterium-tritium (D-T) operation. Testing of the tritium system with low concentration tritium has successfully begun. Simulation of trace and high power D-T experiments using D-D have been performed. The physics objectives of D-T operation are production of ∼ 10 megawatts (MW) of fusion power, evaluation of confinement and heating in deuterium-tritium plasmas, evaluation of α-particle heating of electrons, and collective effects driven by alpha particles and testing of diagnostics for confined α-particles. Experimental results and theoretical modeling in support of the D-T experiments are reviewed

Preparations for deuterium--tritium experiments on the Tokamak Fusion Test Reactor*

International Nuclear Information System (INIS)

Hawryluk, R.J.; Adler, H.; Alling, P.; Ancher, C.; Anderson, H.; Anderson, J.L.; Anderson, J.W.; Arunasalam, V.; Ascione, G.; Aschroft, D.; Barnes, C.W.; Barnes, G.; Batchelor, D.B.; Bateman, G.; Batha, S.; Baylor, L.A.; Beer, M.; Bell, M.G.; Biglow, T.S.; Bitter, M.; Blanchard, W.; Bonoli, P.; Bretz, N.L.; Brunkhorst, C.; Budny, R.; Burgess, T.; Bush, H.; Bush, C.E.; Camp, R.; Caorlin, M.; Carnevale, H.; Chang, Z.; Chen, L.; Cheng, C.Z.; Chrzanowski, J.; Collazo, I.; Collins, J.; Coward, G.; Cowley, S.; Cropper, M.; Darrow, D.S.; Daugert, R.; DeLooper, J.; Duong, H.; Dudek, L.; Durst, R.; Efthimion, P.C.; Ernst, D.; Faunce, J.; Fonck, R.J.; Fredd, E.; Fredrickson, E.; Fromm, N.; Fu, G.Y.; Furth, H.P.; Garzotto, V.; Gentile, C.; Gettelfinger, G.; Gilbert, J.; Gioia, J.; Goldfinger, R.C.; Golian, T.; Gorelenkov, N.; Gouge, M.J.; Grek, B.; Grisham, L.R.; Hammett, G.; Hanson, G.R.; Heidbrink, W.; Hermann, H.W.; Hill, K.W.; Hirshman, S.; Hoffman, D.J.; Hosea, J.; Hulse, R.A.; Hsuan, H.; Jaeger, E.F.; Janos, A.; Jassby, D.L.; Jobes, F.C.; Johnson, D.W.; Johnson, L.C.; Kamperschroer, J.; Kesner, J.; Kugel, H.; Kwon, S.; Labik, G.; Lam, N.T.; LaMarche, P.H.; Laughlin, M.J.; Lawson, E.; LeBlanc, B.; Leonard, M.; Levine, J.; Levinton, F.M.; Loesser, D.; Long, D.; Machuzak, J.; Mansfield, D.E.; Marchlik, M.; Marmar, E.S.; Marsala, R.; Martin, A.; Martin, G.; Mastrocola, V.; Mazzucato, E.; McCarthy, M.P.; Majeski, R.; Mauel, M.; McCormack, B.; McCune, D.C.; McGuire, K.M.; Meade, D.M.; Medley, S.S.; Mikkelsen, D.R.; Milora, S.L.; Monticello, D.; Mueller, D.; Murakami, M.; Murphy, J.A.; Nagy, A.; Navratil, G.A.; Nazikian, R.; Newman, R.; Nishitani, T.; Norris, M.; O'Connor, T.; Oldaker, M.; Ongena, J.; Osakabe, M.; Owens, D.K.; Park, H.; Park, W.; Paul, S.F.; Pavlov, Y.I.; Pearson, G.; Perkins, F.; Perry, E.; Persing, R.; Petrov, M.; Phillips, C.K.; Pitcher, S.; Popovichev, S.; Qualls, A.L.; Raftopoulos, S.; Ramakrishnan, R.; Ramsey, A.; Rasmussen, D.A.; Redi, M.H.

1994-01-01

The final hardware modifications for tritium operation have been completed for the Tokamak Fusion Test Reactor (TFTR) [Fusion Technol. 21, 1324 (1992)]. These activities include preparation of the tritium gas handling system, installation of additional neutron shielding, conversion of the toroidal field coil cooling system from water to a Fluorinert TM system, modification of the vacuum system to handle tritium, preparation, and testing of the neutral beam system for tritium operation and a final deuterium--deuterium (D--D) run to simulate expected deuterium--tritium (D--T) operation. Testing of the tritium system with low concentration tritium has successfully begun. Simulation of trace and high power D--T experiments using D--D have been performed. The physics objectives of D--T operation are production of ∼10 MW of fusion power, evaluation of confinement, and heating in deuterium--tritium plasmas, evaluation of α-particle heating of electrons, and collective effects driven by alpha particles and testing of diagnostics for confined α particles. Experimental results and theoretical modeling in support of the D--T experiments are reviewed

Deuterium content on surface waters VI to X Chile regions

International Nuclear Information System (INIS)

Aravena C, R; Pollastri J, A.; Suzuki S, O.

1984-01-01

One important parameter on any sitting study for a heavy water plant installation is the deuterium content of the feed water. Deuterium data on surface waters from differents areas located in the south of Chile, are presented. These results allow to idently some potential areas for a future heavy water plant. One of these areas, Lago Llanquihue, was sampled more in detail to study the vertical distribution and spatial variations. (Author)

Electrochemically induced nuclear fusion of deuterium

International Nuclear Information System (INIS)

Jorne, J.

1990-01-01

In this paper cold fusion of deuterium by electrolysis of heavy water onto a palladium (or titanium) cathode is reported. Contrary to the assumption of Fleishmann and Pons that electrochemically compressed D + exists inside the palladium cathode, the observations of Jones et al. can be partially explained by the simultaneous presence of deuteride D - and the highly mobile positive deuterium ion D + . The opposite charges reduce the intranuclear distance and enhance the tunneling fusion rate. Furthermore, alloying of lithium with palladium can stabilize a negatively charged deuteride ion due to the salinelike character of lithium deuteride. The enormous pressure (or fugacity), achieved by the applied electrochemical potential (10 30 atm), is a virtual pressure that would have existed in equilibrium with palladium deuteride (PdD x ). It is speculated that nuclear fusion occurs at the surface, and the PdD x serves as a reservoir for the supply of deuteride ions

Reflection of 32--2000 eV deuterium from carbon

International Nuclear Information System (INIS)

Braun, M.; Thomas, E.W.

1982-01-01

Reflection of deuterium from carbon is measured by a technique based on the rise of partial pressure caused by the reflected particles. Data are presented for 32--2000 eV per deuteron incident energies and as a function of angle of incidence. The data are consistent with previous determinations at energies above 1000 eV. A systematic difference in energy dependence is found when the measurements for reflection of deuterium are compared on a reduced energy scale with MARLOWE computer simulations of hydrogen reflection

Influence of deuterium-depleted water on living organisms

International Nuclear Information System (INIS)

Stefanescu, I.; Titescu, Gh.; Croitoru, Cornelia; Saros-Rogobete, Irina

2000-01-01

Deuterium-depleted water (DDW) production technique consists in the separation of deuterium from water by means of an continuos distillation process under a pressure value of about 133,3 mbar. Water that is used as basic material has an isotopic content of 144 ppm D/(D+H). DDW results as distillate with an isotopic deuterium content of 15-80 ppm, depending on the level we want to achieve. Beginning with 1996 NIR and DCIT Rm. Valcea, which is a DDW producer, co-operated with Romanian specialised institutes for biological effects' evaluation of DDW. These investigations led to the next conclusions: - DDW caused a tendency towards the increase of the basal tone, accompanied by the intensification of the vasoconstrictor effects of phenylefrine, noradrenaline and angiotensin; the increase of the basal tonus and vascular reactivity produced by the DDW persist after the removal of the vascular endothelium; - Animals treated with DDW showed an increase of the resistance both to sublethal and to lethal gamma radiation doses, suggesting a radioprotective action by the stimulation of non-specific immune defence mechanisms; - DDW stimulate immune defence reactions, represented by the opsonic, bactericidal and phagocyte capacity of the immune system, together with increase in the numbers of polymorphonuclear neutrophils; - Investigations regarding artificial reproduction of fish with DDW fecundated solutions confirmed favourable influence in embryo growth stage and resistance in next growth stages; - It was studied germination, growth and quantitative characters' variability at plants; one can remark the favourable influence of DDW on biological process at plants in various ontogenic stages. Further investigations are needed in order to establish the influence of deuterium-depleted water on living organisms. (authors)

Hydrogen/deuterium exchange in mass spectrometry.

Science.gov (United States)

Kostyukevich, Yury; Acter, Thamina; Zherebker, Alexander; Ahmed, Arif; Kim, Sunghwan; Nikolaev, Eugene

2018-03-30

The isotopic exchange approach is in use since the first observation of such reactions in 1933 by Lewis. This approach allows the investigation of the pathways of chemical and biochemical reactions, determination of structure, composition, and conformation of molecules. Mass spectrometry has now become one of the most important analytical tools for the monitoring of the isotopic exchange reactions. Investigation of conformational dynamics of proteins, quantitative measurements, obtaining chemical, and structural information about individual compounds of the complex natural mixtures are mainly based on the use of isotope exchange in combination with high resolution mass spectrometry. The most important reaction is the Hydrogen/Deuterium exchange, which is mainly performed in the solution. Recently we have developed the approach allowing performing of the Hydrogen/Deuterium reaction on-line directly in the ionization source under atmospheric pressure. Such approach simplifies the sample preparation and can accelerate the exchange reaction so that certain hydrogens that are considered as non-labile will also participate in the exchange. The use of in-ionization source H/D exchange in modern mass spectrometry for structural elucidation of molecules serves as the basic theme in this review. We will focus on the mechanisms of the isotopic exchange reactions and on the application of in-ESI, in-APCI, and in-APPI source Hydrogen/Deuterium exchange for the investigation of petroleum, natural organic matter, oligosaccharides, and proteins including protein-protein complexes. The simple scenario for adaptation of H/D exchange reactions into mass spectrometric method is also highlighted along with a couple of examples collected from previous studies. © 2018 Wiley Periodicals, Inc.

Analysis of the interaction of deuterium plasmas with tungsten in the Fuego-Nuevo II device

Science.gov (United States)

Ramos, Gonzalo; Castillo, Fermín; Nieto, Martín; Martínez, Marco; Rangel, José; Herrera-Velázquez, Julio

2012-10-01

Tungsten is one of the main candidate materials for plasma-facing components in future fusion power plants. The Fuego-Nuevo II, a plasma focus device, which can produce dense magnetized helium and deuterium plasmas, has been adapted to address plasma-facing materials questions. In this paper we present results of tungsten targets exposed to deuterium plasmas in the Fuego Nuevo II device, using different experimental conditions. The plasma generated and accelerated in the coaxial gun is expected to have, before the pinch, energies of the order of hundreds eV and velocities of the order of 40,000 m s-1. At the pinch, the ions are reported to have energies of the order of 1.5 keV at most. The samples, analysed with a scanning electron microscope (SEM) in cross section show a damage profile to depths of the order of 580 nm, which are larger than those expected for ions with 1.5 keV, and may be evidence of ion acceleration. An analysis with the SRIM (Stopping Range of Ions in Matter) package calculations is shown.

Natural abundance deuterium nuclear magnetic resonance spectroscopy: Study of the biosynthesis of monoterpenes

International Nuclear Information System (INIS)

Leopold, M.F.

1990-01-01

Deuterium NMR spectroscopy at natural abundance (D NMR-na) is a new technique for exploring the biosynthesis of small molecules such as monoterpenes. The analysis of relative site-specific deuterium integration values is an effective means of measuring isotope effects, and examining the regio- and stereochemistry of biosynthetic reactions. The deuterium integration values of linalyl acetate and limonene isolated from the same source were consistent and showed that proton abstraction from the postulated α-terpinyl cation intermediate to form limonene is regioselective from the methyl derived from the Cs methyl of the precursor, geranyl diphosphate. This regiochemistry was observed in limonene samples from different sources and the measured primary kinetic isotope effect ranged from 0.25 to in excess of 100 (no deuterium was removed within experimental error). Various α- and β-pinene samples were isolated and D NMR-na analysis showed evidence of isotopically sensitive partitioning of the pinylcation in the formation of these products. This spectral analysis supported published radiolabeling studies but did not require synthesis of substrates or enzyme purification. The formation of 3-carene occurs without isomerization of the double bond which was previously postulated. The olefinic deuterium of the bicyclic compound was traced to the depleted deuterium at C 2 of isopentyl diphosphate by D NMR-na data and this supported unpublished radiolabeling studies. Study of irregular monoterpenes, chrysanthemyl acetate and lyratyl acetate, showed partitioning of dimethylallyl diphosphate (DMAPP) by chrysanthemyl cyclase. The α-secondary kinetic isotope effect of 1.06-1.12, obtained from relative deuterium integration values, suggested that S N 1 ionization of one molecule of DMAPP is the first step in the condensation reaction

Deuterium oxide as a tool for the study of amino acid metabolism

International Nuclear Information System (INIS)

Mitra, R.; Burton, J.; Varner, J.E.

1976-01-01

We have used deuterium oxide in nontoxic concentrations to study, in intact seedlings, the biosynthesis of amino acids. The extent and pattern of deuteration, as determined by a gas--liquid chromatograph--mass spectrometer system, permits conclusions about the biosynthesis of individual amino acids and also about their exposure to transaminases and other enzymes that might introduce deuterium into specific positions of the amino acid by exchange. This method could be used to study amino acid biogenesis in any organism that can tolerate 20 to 40 percent deuterium oxide for a period of a few hours to a few days

High resolution deuterium NMR studies of bacterial metabolism

Energy Technology Data Exchange (ETDEWEB)

Aguayo, J.B.; Gamcsik, M.P.; Dick, J.D.

1988-12-25

High resolution deuterium NMR spectra were obtained from suspensions of five bacterial strains: Escherichia coli, Clostridium perfringens, Klebsiella pneumoniae, Proteus mirabilis, and Staphylococcus aureus. Deuterium-labeled D-glucose at C-1, C-2, and C-6 was used to monitor dynamically anaerobic metabolism. The flux of glucose through the various bacterial metabolic pathways could be determined by following the disappearance of glucose and the appearance of the major end products in the 2H NMR spectrum. The presence of both labeled and unlabeled metabolites could be detected using 1H NMR spectroscopy since the proton resonances in the labeled species are shifted upfield due to an isotopic chemical shift effect. The 1H-1H scalar coupling observed in both the 2H and 1H NMR spectra was used to assign definitively the resonances of labeled species. An increase in the intensity of natural abundance deuterium signal of water can be used to monitor pathways in which a deuteron is lost from the labeled metabolite. The steps in which label loss can occur are outlined, and the influence these processes have on the ability of 2H NMR spectroscopy to monitor metabolism are assessed.

High resolution deuterium NMR studies of bacterial metabolism

International Nuclear Information System (INIS)

Aguayo, J.B.; Gamcsik, M.P.; Dick, J.D.

1988-01-01

High resolution deuterium NMR spectra were obtained from suspensions of five bacterial strains: Escherichia coli, Clostridium perfringens, Klebsiella pneumoniae, Proteus mirabilis, and Staphylococcus aureus. Deuterium-labeled D-glucose at C-1, C-2, and C-6 was used to monitor dynamically anaerobic metabolism. The flux of glucose through the various bacterial metabolic pathways could be determined by following the disappearance of glucose and the appearance of the major end products in the 2H NMR spectrum. The presence of both labeled and unlabeled metabolites could be detected using 1H NMR spectroscopy since the proton resonances in the labeled species are shifted upfield due to an isotopic chemical shift effect. The 1H-1H scalar coupling observed in both the 2H and 1H NMR spectra was used to assign definitively the resonances of labeled species. An increase in the intensity of natural abundance deuterium signal of water can be used to monitor pathways in which a deuteron is lost from the labeled metabolite. The steps in which label loss can occur are outlined, and the influence these processes have on the ability of 2H NMR spectroscopy to monitor metabolism are assessed

Deuterium and oxygen-18 abundance in birds: Implications for DLW energetics studies

International Nuclear Information System (INIS)

Tatner, P.

1990-01-01

The doubly labeled water (DLW) technique for measuring energy expenditure may employ one ( 18 O) or two ( 18 O and deuterium) stable isotopes as tracers. These occur naturally in the environment, so when they are used as tracers it is necessary to subtract the background levels. Few studies report data on background concentrations. This work provides such data for a range of avian species. Overall, there was a strong positive correlation (r = 0.63) between the 18 O and deuterium concentrations in birds' body water. Variation in the deuterium concentration was less extensive than in the 18 O concentration (1:2.7 parts/million). In the European robin, there was a linked, seasonal variation in 18 O and deuterium abundance producing high summer and low winter values. Throughout the year, a high individual variability was greater in 18 O than in deuterium. A difference between the European robin and the dipper suggests that habitat may also influence background abundance. Investigation of the effect of variation in background abundance on measures of energy expenditure for small passerines (20 g) revealed that employing estimates, instead of direct measurements, had a minor influence over an experimental period of 1 day but could potentially introduce errors as large as 54% over a 2-day period

Process for the separation of deuterium and tritium from water using ammonia and a hydrogen-nitrogen-mixture

International Nuclear Information System (INIS)

Mandrin, Ch.

1986-01-01

A multistage process for separation of deuterium and tritium from water using ammonia and a hydrogen-nitrogen mixture. In a first stage isotopic exchange takes place between water containing deuterium and tritium, and ammonia depleted in deuterium and tritium. The molar ammonia throughput is chosen to be greater than two third of the molar throughput of water. The advantage of the process consists in the fact that the main product is water almost entirely free from deuterium and tritium. The byproducts are compounds enriched in deuterium and tritium, and nitrogen enriched in N-15

Deuterium trapping at vacancy clusters in electron/neutron-irradiated tungsten studied by positron annihilation spectroscopy

Science.gov (United States)

Toyama, T.; Ami, K.; Inoue, K.; Nagai, Y.; Sato, K.; Xu, Q.; Hatano, Y.

2018-02-01

Deuterium trapping at irradiation-induced defects in tungsten, a candidate material for plasma facing components in fusion reactors, was revealed by positron annihilation spectroscopy. Pure tungsten was electron-irradiated (8.5 MeV at ∼373 K and to a dose of ∼1 × 10-3 dpa) or neutron-irradiated (at 573 K to a dose of ∼0.3 dpa), followed by post-irradiation annealing at 573 K for 100 h in deuterium gas of ∼0.1 MPa. In both cases of electron- or neutron-irradiation, vacancy clusters were found by positron lifetime measurements. In addition, positron annihilation with deuterium electrons was demonstrated by coincidence Doppler broadening measurements, directly indicating deuterium trapping at vacancy-type defects. This is expected to cause significant increase in deuterium retention in irradiated-tungsten.

Reducing deuterium-tritium ice roughness by electrical heating of the saturated vapor

International Nuclear Information System (INIS)

Mapoles, E.R.; Sater, J.D.; Monsler, E.; Pipes, J.

1996-01-01

High gain targets for inertial confinement fusion (ICF) contain a layer of deuterium-tritium (DT) ice which surrounds a volume of DT gas in thermal equilibrium with the solid. The roughness of the cryogenic fuel layer inside of ICF targets is one of the sources of imperfections which cause implosions to deviate from perfect one dimensional performance. Experiments at Lawrence Livermore National Laboratory have shown that applying a heat flux across the inner surface of a hydrogen layer such as that inside an ICF target reduces the intrinsic roughness of the surface. We have developed a technique to generate this heat flux by applying and electric field to the DT vapor in the center of these shells. This vapor has a small but significant conductivity due to ionization caused by beta decay of tritium in the vapor and the solid. We describe here experiments using a 1.15 GHz cavity to apply an electric field to frozen DT inside of a sapphire test cell. The cell and cavity geometry allows visual observation of the frozen layers

Deuterium ion irradiation induced blister formation and destruction

Energy Technology Data Exchange (ETDEWEB)

Song, Jaemin; Kim, Nam-Kyun; Kim, Hyun-Su; Jin, Younggil; Roh, Ki-Baek; Kim, Gon-Ho, E-mail: ghkim@snu.ac.kr

2016-11-01

Highlights: • The areal number density of blisters on the grain with (1 1 1) plane orientation increased with increasing ion fluence. • No more blisters were created above the temperature about 900 K due to high thermal mobility of ions and inactivity of traps. • The destruction of blister at the boundary induced by sputtering is proposed. • The blisters were destructed at the position about the boundary by high sputtering yield of oblique incident ions and thin thickness due to plastic deformation at the boundary. - Abstract: The blisters formation and destruction induced by the deuterium ions on a polycrystalline tungsten were investigated with varying irradiation deuterium ion fluence from 3.04 × 10{sup 23} to 1.84 × 10{sup 25} D m{sup −2} s{sup −1} and an fixed irradiated ion energy of 100 eV in an electron cyclotron resonance plasma source, which was similar to the far-scrape off layer region in the nuclear fusion reactors. Target temperature was monitored during the irradiation. Most of blisters formed easily on the grain with (1 1 1) plane orientation which had about 250 nm in diameter. In addition, the areal number density of blisters increased with increasing the ion fluence under the surface temperature reaching to about 900 K. When the fluence exceeded 4.6 × 10{sup 24} D m{sup −2}, the areal number density of the blister decreased. It could be explained that the destruction of the blister was initiated by erosion at the boundary region where the thickness of blister lid was thin and the sputtering yield was high by oblique incident ions, resulting in remaining the lid open, e.g., un-eroded center dome. It is possible to work as a tungsten dust formation from the plasma facing divertor material at far-SOL region of fusion reactor.

Catalytic isotope exchange reaction between deuterium gas and water pre-adsorbed on platinum/alumina

International Nuclear Information System (INIS)

Iida, Itsuo; Kato, Junko; Tamaru, Kenzi.

1976-01-01

The catalytic isotope exchange reaction between deuterium gas and the water pre-adsorbed on Pt/Al 2 O 3 was studied. At reaction temperatures above 273 K, the exchange rate was proportional to the deuterium pressure and independent of the amount of adsorbed water, which suggests that the rate determining step is the supply of deuterium from the gas phase. Its apparent activation energy was 38 kJ mol -1 . Below freezing point of water, the kinetic behaviour was different from that above freezing point. At higher deuterium pressures the rate dropped abruptly at 273 K. Below the temperature the apparent activation energy was 54 kJ mol -1 and the exchange rate depended not on the deuterium pressure but on the amount of the pre-adsorbed water. At lower pressures, however, the kinetic behaviour was the same as the above 273 K, till the rate of the supply of deuterium from the gas phase exceeded the supply of hydrogen from adsorbed water to platinum surface. These results suggest that below 273 K the supply of hydrogen is markedly retarded, the state of the adsorbed water differing from that above 273 K. It was also demonstrated that when the adsorbed water is in the state of capillary condensation, the exchange rate becomes very small. (auth.)

Deuterium fractionation mechanisms in interstellar clouds

International Nuclear Information System (INIS)

Dalgarno, A.; Lepp, S.

1984-01-01

The theory of the fractionation of deuterated molecules is extended to include reactions with atomic deuterium. With the recognition that dissociative recombination of H + 3 is not rapid, observational data can be used in conjunction with the theory to derive upper and lower bounds to the cosmic deuterium-hydrogen abundance ratio. We find that [D]/[H] is at least 3.4 x 10 -6 and at most 4.0 x 10 -5 with a probable value of 1 x 10 -5 . Because of the reaction HCO + +D→DCO + +H, upper limits can be derived for the fractional ionization which depend only weakly on the cosmic ray flux, zeta. In four clouds, the upper limits to the fractional ionization lie between 1.1 x 10 -6 and 1.5 x 10 -6 if zeta = 10 -7 s -1 and between 3.1 x 10 -6 and 1.8 x 10 -6 if zeta = 10 -16 s -1

High-energy neutrino background: Limitations on models of deuterium production

International Nuclear Information System (INIS)

Eichler, D.

1979-01-01

It is pointed out that Epstein's model for deuterium production via high-energy spallation reactions produces high-energy neutrinos in sufficient quantity to stand out above those that are produced by cosmic-ray interactions in the Earth's atmosphere. That the Reines experiment detected neutrinos of atmospheric origin without detecting any cosmic component restricts deuterium production by spallation reactions to very high redshifts (z> or approx. =300). Improved neutrino experiments may be able to push these limits back to recombination

Influence of particle flux density and temperature on surface modifications of tungsten and deuterium retention

International Nuclear Information System (INIS)

Buzi, Luxherta; Temmerman, Greg De; Unterberg, Bernhard; Reinhart, Michael; Litnovsky, Andrey; Philipps, Volker; Oost, Guido Van; Möller, Sören

2014-01-01

Systematic study of deuterium irradiation effects on tungsten was done under ITER – relevant high particle flux density, scanning a broad surface temperature range. Polycrystalline ITER – like grade tungsten samples were exposed in linear plasma devices to two different ranges of deuterium ion flux densities (high: 3.5–7 · 10 23 D + /m 2 s and low: 9 · 10 21 D + /m 2 s). Particle fluence and ion energy, respectively 10 26 D + /m 2 and ∼38 eV were kept constant in all cases. The experiments were performed at three different surface temperatures 530 K, 630 K and 870 K. Experimental results concerning the deuterium retention and surface modifications of low flux exposure confirmed previous investigations. At temperatures 530 K and 630 K, deuterium retention was higher at lower flux density due to the longer exposure time (steady state plasma operation) and a consequently deeper diffusion range. At 870 K, deuterium retention was found to be higher at high flux density according to the thermal desorption spectroscopy (TDS) measurements. While blisters were completely absent at low flux density, small blisters of about 40–50 nm were formed at high flux density exposure. At the given conditions, a relation between deuterium retention and blister formation has been found which has to be considered in addition to deuterium trapping in defects populated by diffusion

Deuterium absorption in CANDU Zr-2.5Nb pressure tubes

International Nuclear Information System (INIS)

Ploc, R.A.; McRae, G.A.

1999-12-01

Corrosion of CANDU Zr-2.5%Nb pressure tubes in heavy water results in the formation of an oxide film and the absorption of deuterium by the alloy. If deuterium concentrations are allowed to exceed the terminal solid solubility of the alloy, brittle deuterides can form, thereby limiting the service life of a component. In CANDU pressure tubes, ingress rates are largely determined by the metastable β-Zr that is present as a thin layer encasing the predominant α-Zr grains (approximately 90% by volume). The distribution and continuity of the corroded β-phase in the oxide provides a pervasive web for the development of interconnected porosity from the free surface to the oxide/metal interface. Changing the distribution of the β-phase in the alloy changes the nature of the oxide porosity, a technique that can be used to reduce deuterium ingress rates. (author)

Deuterium absorption in CANDU Zr-2.5Nb pressure tubes

Energy Technology Data Exchange (ETDEWEB)

Ploc, R.A.; McRae, G.A

1999-12-01

Corrosion of CANDU Zr-2.5%Nb pressure tubes in heavy water results in the formation of an oxide film and the absorption of deuterium by the alloy. If deuterium concentrations are allowed to exceed the terminal solid solubility of the alloy, brittle deuterides can form, thereby limiting the service life of a component. In CANDU pressure tubes, ingress rates are largely determined by the metastable {beta}-Zr that is present as a thin layer encasing the predominant {alpha}-Zr grains (approximately 90% by volume). The distribution and continuity of the corroded {beta}-phase in the oxide provides a pervasive web for the development of interconnected porosity from the free surface to the oxide/metal interface. Changing the distribution of the {beta}-phase in the alloy changes the nature of the oxide porosity, a technique that can be used to reduce deuterium ingress rates. (author)

Inertial-confinement-fusion targets

International Nuclear Information System (INIS)

Hendricks, C.D.

1982-01-01

Much of the research in laser fusion has been done using simple ball on-stalk targets filled with a deuterium-tritium mixture. The targets operated in the exploding pusher mode in which the laser energy was delivered in a very short time (approx. 100 ps or less) and was absorbed by the glass wall of the target. The high energy density in the glass literally exploded the shell with the inward moving glass compressing the DT fuel to high temperatures and moderate densities. Temperatures achieved were high enough to produce DT reactions and accompanying thermonuclear neutrons and alpha particles. The primary criteria imposed on the target builders were: (1) wall thickness, (2) sphere diameter, and (3) fuel in the sphere

Hydrogen and deuterium NMR of solids by magic-angle spinning

International Nuclear Information System (INIS)

Eckman, R.R.

1982-10-01

The nuclear magnetic resonance of solids has long been characterized by very large specral broadening which arises from internuclear dipole-dipole coupling or the nuclear electric quadrupole interaction. These couplings can obscure the smaller chemical shift interaction and make that information unavailable. Two important and difficult cases are that of hydrogen and deuterium. The development of cross polarization, heteronuclear radiofrequency decoupling, and coherent averaging of nuclear spin interactions has provided measurement of chemical shift tensors in solids. Recently, double quantum NMR and double quantum decoupling have led to measurement of deuterium and proton chemical shift tensors, respectively. A general problem of these experiments is the overlapping of the tensor powder pattern spectra of magnetically distinct sites which cannot be resolved. In this work, high resolution NMR of hydrogen and deuterium in solids is demonstrated. For both nuclei, the resonances are narrowed to obtain liquid-like isotropic spectra by high frequency rotation of the sample about an axis inclined at the magic angle, β/sub m/ = Arccos (3/sup -1/2/), with respect to the direction of the external magnetic field. For deuterium, the powder spectra were narrowed by over three orders of magnitude by magic angle rotation with precise control of β. A second approach was the observation of deuterium double quantum transitions under magic angle rotation. For hydrogen, magic angle rotation alone could be applied to obtain the isotropic spectrum when H/sub D/ was small. This often occurs naturally when the nuclei are semi-dilute or involved in internal motion. In the general case of large H/sub D/, isotropic spectra were obtained by dilution of 1 H with 2 H combined with magic angle rotation. The resolution obtained represents the practical limit for proton NMR of solids

Fractionation of deuterium and protium between water and methanol

International Nuclear Information System (INIS)

Rolston, J.H.; Gale, K.L.

1984-01-01

The overall deuterium-protium separation factor, α, between hydrogen gas and aqueous methanol mixtures has been measured over the full composition range at temperatures between 25 and 55 0 C. At each temperature α increases smoothly with increasing mole fraction of methanol but the values fall significantly below the straight line joining the separation factors for the methanol-hydrogen and water-hydrogen systems. The equilibrium constant, K 1 (1), for exchange of a deuterium atom tracer between the hydroxyl groups of methanol and liquid water, calculated from the values of α for each solution, is independent of composition within experimental error. The value of K 1 (1) at 25 0 C is 0.54 +/- 0.02, so that deuterium favors the methanol environment rather than water. The dependence of k 1 (1) on absolute temperature, T, is given by the expression 1n K 1 (1) = -0.776 + 52.6/T, which corresponds to a reaction enthalpy of -0.43 kJ mol -1 . 24 references, 2 figures, 2 tables

Deuterium depth profiles in metals using imaging field desorption

International Nuclear Information System (INIS)

Panitz, J.A.

1976-01-01

Depth profiles of 80 eV deuterium ions implanted in-situ into (110) tungsten have been measured by Imaging, Field-Desorption Mass Spectrometry. The relative abundance of deuterium was measured from the surface to a depth of 300A with less than 3A depth resolution by controlled field-evaporation of the specimen, and time-of-flight mass spectroscopy. The position of the depth distribution maximum (57 +- 3A from the surface) is shown to be in close agreement with that predicted theoretically for low energy deuterium implants using an amorphous-solid model. Structure in the distribution is attributed to surface morphology and channeling phenomena in the near surface region. Implanted impurity species from the ion source and tungsten surface have also been observed. For C + , C 2+ and 0 + , penetration is limited to less than 30A, with abundance decreasing exponentially from the surface. These results are interpreted in the context of the CTR first-wall impurity problem, and are used to suggest a novel method for in-situ characterization of low energy plasma species in operating CTR devices

One Percent Determination of the Primordial Deuterium Abundance

Science.gov (United States)

Cooke, Ryan J.; Pettini, Max; Steidel, Charles C.

2018-03-01

We report a reanalysis of a near-pristine absorption system, located at a redshift {z}abs}=2.52564 toward the quasar Q1243+307, based on the combination of archival and new data obtained with the HIRES echelle spectrograph on the Keck telescope. This absorption system, which has an oxygen abundance [O/H] = ‑2.769 ± 0.028 (≃1/600 of the solar abundance), is among the lowest metallicity systems currently known where a precise measurement of the deuterium abundance is afforded. Our detailed analysis of this system concludes, on the basis of eight D I absorption lines, that the deuterium abundance of this gas cloud is {log}}10({{D}}/{{H}})=-4.622+/- 0.015, which is in very good agreement with the results previously reported by Kirkman et al., but with an improvement on the precision of this single measurement by a factor of ∼3.5. Combining this new estimate with our previous sample of six high precision and homogeneously analyzed D/H measurements, we deduce that the primordial deuterium abundance is {log}}10{({{D}}/{{H}})}{{P}}=-4.5974+/- 0.0052 or, expressed as a linear quantity, {10}5{({{D}}/{{H}})}{{P}}=2.527+/- 0.030; this value corresponds to a one percent determination of the primordial deuterium abundance. Combining our result with a big bang nucleosynthesis (BBN) calculation that uses the latest nuclear physics input, we find that the baryon density derived from BBN agrees to within 2σ of the latest results from the Planck cosmic microwave background data. Based on observations collected at the W.M. Keck Observatory which is operated as a scientific partnership among the California Institute of Technology, the University of California, and the National Aeronautics and Space Administration. The Observatory was made possible by the generous financial support of the W.M. Keck Foundation.

The Variability of Atmospheric Deuterium Brightness at Mars: Evidence for Seasonal Dependence

Science.gov (United States)

Mayyasi, Majd; Clarke, John; Bhattacharyya, Dolon; Deighan, Justin; Jain, Sonal; Chaffin, Michael; Thiemann, Edward; Schneider, Nick; Jakosky, Bruce

2017-10-01

The enhanced ratio of deuterium to hydrogen on Mars has been widely interpreted as indicating the loss of a large column of water into space, and the hydrogen content of the upper atmosphere is now known to be highly variable. The variation in the properties of both deuterium and hydrogen in the upper atmosphere of Mars is indicative of the dynamical processes that produce these species and propagate them to altitudes where they can escape the planet. Understanding the seasonal variability of D is key to understanding the variability of the escape rate of water from Mars. Data from a 15 month observing campaign, made by the Mars Atmosphere and Volatile Evolution Imaging Ultraviolet Spectrograph high-resolution echelle channel, are used to determine the brightness of deuterium as observed at the limb of Mars. The D emission is highly variable, with a peak in brightness just after southern summer solstice. The trends of D brightness are examined against extrinsic as well as intrinsic sources. It is found that the fluctuations in deuterium brightness in the upper atmosphere of Mars (up to 400 km), corrected for periodic solar variations, vary on timescales that are similar to those of water vapor fluctuations lower in the atmosphere (20-80 km). The observed variability in deuterium may be attributed to seasonal factors such as regional dust storm activity and subsequent circulation lower in the atmosphere.

Estimation of deuterium content in organic compounds by mass spectrometric methods

International Nuclear Information System (INIS)

Dave, S.M.; Goomer, N.C.

1979-01-01

Many organic sompounds are finding increasing importance in heavy water enrichment programme. New methods based on quantitative chemical conversion have been developed and standardized in for estimating deuterium contents of the exchanging organic molecules by mass spectrometry. The methods have been selected in such a way that the deuterium contents of both exchangeable as well as total hydrogens in the molecule can be conveniently estimated. (auth.)

Deuterium permeation and diffusion in high-purity beryllium

International Nuclear Information System (INIS)

Abramov, E.; Riehm, M.P.; Thompson, D.A.; Smeltzer, W.W.

1990-01-01

The permeation rate of deuterium through high-purity beryllium membranes was measured using the gas-driven permeation technique. The time-dependent and the steady-state deuterium flux data were analyzed and the effective diffusivities of the samples were determined. Using multilayer permeation theory the effects of surface oxide were eliminated and the diffusion coefficients of the bulk beryllium determined. The diffusion parameters obtained for the extra-grade beryllium samples (99.8%) are D 0 =6.7x10 -9 m 2 /s and E D =28.4 kJ/mol. For the high-grade beryllium samples (99%) the parameters are D 0 =8.0x10 -9 m 2 /s and E D =35.1 kJ/mol. (orig.)

Effect of experimentally observed hydrogenic fractionation on inertial confinement fusion ignition target performance

International Nuclear Information System (INIS)

McKenty, P. W.; Wittman, M. D.; Harding, D. R.

2006-01-01

The need of cryogenic hydrogenic fuels in inertial confinement fusion (ICF) ignition targets has been long been established. Efficient implosion of such targets has mandated keeping the adiabat of the main fuel layer at low levels to ensure drive energies are kept at reasonable minima. The use of cryogenic fuels helps meet this requirement and has therefore become the standard in most ICF ignition designs. To date most theoretical ICF ignition target designs have assumed a homogeneous layer of deuterium-tritium (DT) fuel kept slightly below the triple point. However, recent work has indicated that, as cryogenic fuel layers are formed inside an ICF capsule, isotopic dissociation of the tritium (T), deuterium (D), and DT takes place leading to a 'fractionation' of the final ice layer. This paper will numerically investigate the effects that various scenarios of fractionation have on hot-spot formation, ignition, and burn in ICF ignition target designs

The Advanced Neutron Source liquid deuterium cold source

International Nuclear Information System (INIS)

Lucas, A.T.

1995-08-01

The Advanced Neutron Source will employ two cold sources to moderate neutrons to low energy (<10 meV). The cold neutrons produced are then passed through beam guides to various experiment stations. Each cold source moderator is a sphere of 410-mm internal diameter. The moderator material is liquid deuterium flowing at a rate of 1 kg/s and maintained at subcooled temperatures at all points of the circuit, to prevent boiling. Nuclear beat deposited within the liquid deuterium and its containment structure totals more than 30 kW. All of this heat is removed by the liquid deuterium, which raises its temperature by 5 K. The liquid prime mover is a cryogenic circulator that is situated in the return leg of the flow loop. This arrangement minimizes the heat added to the liquid between the heat exchanger and the moderator vessel, allowing the moderator to be operated at the minimum practical temperature. This report describes the latest thinking at the time of project termination. It also includes the status of various systems at that time and outlines anticipated directions in which the design would have progressed. In this regard, some detail differences between this report and official design documents reflect ideas that were not approved at the time of closure but are considered noteworthy

Measurement of the deuterium concentration in water samples using a CW chemical deuterium fluoride laser

International Nuclear Information System (INIS)

Trautmann, M.

1979-10-01

In this study a new method for the determination of the deuterium content in water samples is described. The absorption of the radiation of a CW deuterium fluoride laser by the isotope HDO in the water vapor of the sample is measured by means of an optoacoustic detector (spectrophone). Thereby advantage is taken of the fact that H 2 O hardly absorbs the laser radiation and that D 2 O only exists in negligible concentrations. The isotope ratio of hydrogen can be calculated from the measured relative concentration of HDO. In the course of this investigation the relative absorption cross sections of HDO for the different laser lines were determined. It was thereby established that there exists a very good coincidence of an HDO absorption line with the 2P2 laser line. Using a very sensitive nonresonant spectrophone the relative concentration of HDO in natural water samples could be determined with an accuracy of about 10%. The experiments also demonstrated that with appropriate improvements made to the apparatus and using a second spectrophone as a reference it should be possible to increase this accuracy to 0,1%. (orig.)

Compact deuterium-tritium neutron generator using a novel field ionization source

Energy Technology Data Exchange (ETDEWEB)

Ellsworth, J. L., E-mail: ellsworth7@llnl.gov; Falabella, S.; Sanchez, J.; Tang, V. [Lawrence Livermore National Laboratory, 7000 East Avenue, Livermore, California 94550 (United States); Wang, H. [Department of Computer Science, Stanford University, Stanford, California 94305 (United States)

2014-11-21

Active interrogation using neutrons is an effective method for detecting shielded nuclear material. A lightweight, lunch-box-sized, battery-operated neutron source would enable new concepts of operation in the field. We have developed at-scale components for a highly portable, completely self-contained, pulsed Deuterium-Tritium (DT) neutron source producing 14 MeV neutrons with average yields of 10{sup 7} n/s. A gated, field ionization ion source using etched electrodes has been developed that produces pulsed ion currents up to 500 nA. A compact Cockcroft-Walton high voltage source is used to accelerate deuterons into a metal hydride target for neutron production. The results of full scale DT tests using the field ionization source are presented.

Results from deuterium-tritium tokamak confinement experiments

International Nuclear Information System (INIS)

Hawryluk, R.J.

1997-02-01

Recent scientific and technical progress in magnetic fusion experiments has resulted in the achievement of plasma parameters (density and temperature) which enabled the production of significant bursts of fusion power from deuterium-tritium fuels and the first studies of the physics of burning plasmas. The key scientific issues in the reacting plasma core are plasma confinement, magnetohydrodynamic (MHD) stability, and the confinement and loss of energetic fusion products from the reacting fuel ions. Progress in the development of regimes of operation which have both good confinement and are MHD stable have enabled a broad study of burning plasma physics issues. A review of the technical and scientific results from the deuterium-tritium experiments on the Joint European Torus (JET) and the Tokamak Fusion Test Reactor (TFTR) is given with particular emphasis on alpha-particle physics issues

Infrared presensitization photography at deuterium fluoride laser wavelengths

International Nuclear Information System (INIS)

Geary, J.M.; Ross, K.; Suter, K.

1989-01-01

Near-field irradiance distributions of a deuterium flouride laser system are obtained using infrared presensitization photography. This represents the shortest wavelength region to employ this technique thus far

Deuterium permeation of amorphous alumina coating on 316L prepared by MOCVD

Science.gov (United States)

Li, Shuai; He, Di; Liu, Xiaopeng; Wang, Shumao; Jiang, Lijun

2012-01-01

The deuterium permeation behavior of the alumina coating on 316L stainless steel prepared by metal organic chemical vapor deposition (MOCVD) was investigated. The alumina coating was also characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscope (SEM). It was found that the as-prepared coating consisted of amorphous alumina. This alumina coating had a dense, crack-free and homogeneous morphology. Although the alumina coating was amorphous, effective suppression of deuterium permeation was demonstrated. The deuterium permeability of the alumina coating was 51-60 times less than that of the 316L stainless steel and 153-335 times less than that of the referred low activation martensitic steels at 860-960 K.

Influence of particle flux density and temperature on surface modifications of tungsten and deuterium retention

Energy Technology Data Exchange (ETDEWEB)

Buzi, Luxherta, E-mail: l.buzi@fz-juelich.de [Ghent University, Department of Applied Physics, Sint-Pietersnieuwstraat 41, B-9000 Ghent (Belgium); FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research, Edisonbaan 14, 3439 MN, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Institut für Energie und Klimaforschung – Plasmaphysik, Forschungszentrum Jülich GmbH, Leo-Brandt-Straße, 52425 Jülich (Germany); Université de Lorraine, Institut Jean Lamour, CNRS UMR 7198, Bvd. des Aiguillettes, F-54506 Vandoeuvre (France); Temmerman, Greg De [FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research, Edisonbaan 14, 3439 MN, PO Box 1207, 3430 BE Nieuwegein (Netherlands); Unterberg, Bernhard; Reinhart, Michael; Litnovsky, Andrey; Philipps, Volker [Institut für Energie und Klimaforschung – Plasmaphysik, Forschungszentrum Jülich GmbH, Leo-Brandt-Straße, 52425 Jülich (Germany); Oost, Guido Van [Ghent University, Department of Applied Physics, Sint-Pietersnieuwstraat 41, B-9000 Ghent (Belgium); Möller, Sören [Institut für Energie und Klimaforschung – Plasmaphysik, Forschungszentrum Jülich GmbH, Leo-Brandt-Straße, 52425 Jülich (Germany)

2014-12-15

Systematic study of deuterium irradiation effects on tungsten was done under ITER – relevant high particle flux density, scanning a broad surface temperature range. Polycrystalline ITER – like grade tungsten samples were exposed in linear plasma devices to two different ranges of deuterium ion flux densities (high: 3.5–7 · 10{sup 23} D{sup +}/m{sup 2} s and low: 9 · 10{sup 21} D{sup +}/m{sup 2} s). Particle fluence and ion energy, respectively 10{sup 26} D{sup +}/m{sup 2} and ∼38 eV were kept constant in all cases. The experiments were performed at three different surface temperatures 530 K, 630 K and 870 K. Experimental results concerning the deuterium retention and surface modifications of low flux exposure confirmed previous investigations. At temperatures 530 K and 630 K, deuterium retention was higher at lower flux density due to the longer exposure time (steady state plasma operation) and a consequently deeper diffusion range. At 870 K, deuterium retention was found to be higher at high flux density according to the thermal desorption spectroscopy (TDS) measurements. While blisters were completely absent at low flux density, small blisters of about 40–50 nm were formed at high flux density exposure. At the given conditions, a relation between deuterium retention and blister formation has been found which has to be considered in addition to deuterium trapping in defects populated by diffusion.

A spin-filter polarimeter for low energy hydrogen and deuterium ion beams

International Nuclear Information System (INIS)

Lemieux, S.K.; Clegg, T.B.; Karwowski, H.J.; Thompson, W.J.; Crosson, E.R.

1993-01-01

An efficient polarimeter which reveals populations of individual hyperfine states of nuclear-spin-polarized H ± (or D ± ) ion beams has been tested. This device is based on unique properties of a three-level interaction in the 2S 1/2 and 2P 1/2 states of hydrogen (or deuterium) atoms, created when the incident, polarized ion beams undergo electron pickup in cesium vapour. Used on a polarized ion source, its efficiency faciy facilitates both rapid optimization and continual monitoring of parameters that affect the beam polarization. With such sources, and perhaps in applications with polarized gas jet targets, the device has potential for an absolute accuracy of better than 2%. (orig.)

Damage, trapping and desorption at the implantation of helium and deuterium in graphite, diamond and silicon carbide

International Nuclear Information System (INIS)

Lopez, G.A.R.

1995-07-01

The production, thermal stability and structure of ion induced defects have been studied by Rutherford backscattering in channeling geometry for the implantation of helium and deuterium in graphite, diamond and silicon carbide with energies of 8 and 20 keV. At the implantation of deuterium and helium ions more defects were measured in graphite than in diamond or silicon carbide at equal experimental conditions. This is due to increased backscattering in graphite, which is caused by the splitting and tilting of crystallites and a local reordering of lattice atoms around defects. At 300 K, Helium produces more defects in all three materials than deuterium with equal depth distribution of defects. The ratio of the defects produced by helium and deuterium agrees very well with the corresponding ratio of the energy deposited in nuclear collisions. In graphite, only small concentrations of deuterium induced defects anneal below 800 K, while in diamond small concentrations of deuterium as well as of helium induced defects anneal mostly below 800 K. This annealing behavior is considered to be due to recombination of point defects. The buildup of helium and deuterium in graphite is different. The trapping of deuterium proceeds until saturation is reached, while in the case of helium trapping is interrupted by flaking. In diamond, deuterium as well as helium are trapped almost completely until at higher fluences reemission starts and saturation is reached. Two desorption mechanisms were identified for the thermal desorption of helium from base-oriented graphite. Helium implanted at low fluences desorbs diffusing to the surface, while for the implantation of high fluences the release of helium due to blistering dominates. The desorption of deuterium from graphite and diamond shows differences. While in graphite the desorption starts already at 800 K, in diamond up to 1140 K only little desorption can be observed. These differences can be explained by the different transport

The Effect of Ion Energy and Substrate Temperature on Deuterium Trapping in Tungsten

Science.gov (United States)

Roszell, John Patrick Town

Tungsten is a candidate plasma facing material for next generation magnetic fusion devices such as ITER and there are major operational and safety issues associated with hydrogen (tritium) retention in plasma facing components. An ion gun was used to simulate plasma-material interactions under various conditions in order to study hydrogen retention characteristics of tungsten thus enabling better predictions of hydrogen retention in ITER. Thermal Desorption Spectroscopy (TDS) was used to measure deuterium retention from ion irradiation while modelling of TDS spectra with the Tritium Migration Analysis Program (TMAP) was used to provide information about the trapping mechanisms involved in deuterium retention in tungsten. X-ray Photoelectron Spectroscopy (XPS) and Secondary Ion Mass Spectrometry (SIMS) were used to determine the depth resolved composition of specimens used for irradiation experiments. Carbon and oxygen atoms will be among the most common contaminants within ITER. C and O contamination in polycrystalline tungsten (PCW) specimens even at low levels (˜0.1%) was shown to reduce deuterium retention by preventing diffusion of deuterium into the bulk of the specimen. This diffusion barrier was also responsible for the inhibition of blister formation during irradiations at 500 K. These observations may provide possible mitigation techniques for problems associated with tritium retention and mechanical damage to plasma facing components caused by hydrogen implantation. Deuterium trapping in PCW and single crystal tungsten (SCW) was studied as a function of ion energy and substrate temperature. Deuterium retention was shown to decrease with decreasing ion energy below 100 eV/D+. Irradiation of tungsten specimens with 10 eV/D+ ions was shown to retain up to an order of magnitude less deuterium than irradiation with 500 eV/D+ ions. Furthermore, the retention mechanism for deuterium was shown to be consistent across the entire energy range studied (10-500 e

Influence of He ions irradiation on the deuterium permeation and retention behavior in the CLF-1 steel

International Nuclear Information System (INIS)

Xu, Yu-Ping; Lu, Tao; Li, Xiao-Chun; Liu, Feng; Liu, Hao-Dong; Wang, Jing; An, Zhong-Qing; Ding, Fang; Hong, Suk-Ho; Zhou, Hai-Shan; Luo, Guang-Nan

2016-01-01

To evaluate the influence of He ions irradiation on the deuterium permeation and retention behavior in RAFM steels, samples made of the CLF-1 steel was irradiated with 3.5 MeV He ions. Gas driven permeation experiments were performed, and the permeability of virgin sample and pre-irradiated sample were obtained and compared. In order to characterize the effect of He ions irradiation on the deuterium retention behavior, deuterium gas exposure was carried out at 623 K, followed by thermal desorption spectra experiments. The total deuterium retention of the CLF-1 steel increased owing to He ions implantation, which could be attributed to the increase in trapping site for deuterium by the He pre-irradiation.

Neutron cross-sections of deuterium in the energy range 0.0001eV-15MeV

International Nuclear Information System (INIS)

Bazazyants, N.O.; Zabrodskaya, A.S.; Larina, A.F.; Nikolaev, M.N.

1978-08-01

The paper describes the evaluation of deuterium neutron cross-sections, the spectra of neutrons from the reaction D(n,2n)P and the angular distributions of neutrons from this reaction and of neutrons elastically scattered on deuterium. The evaluation results are presented in the SOCRATOR format. The 26-group system of constants for deuterium is also presented. (author)

Near-threshold photoproduction of {phi} mesons from deuterium

Energy Technology Data Exchange (ETDEWEB)

Qian, X., E-mail: xqian@caltech.ed [Duke University, Durham, NC 27708 (United States); Kellogg Radiation Laboratory, California Institute of Technology, CA 91125 (United States); Chen, W.; Gao, H. [Duke University, Durham, NC 27708 (United States); Hicks, K. [Ohio University, Athens, OH 45701 (United States); Kramer, K. [Duke University, Durham, NC 27708 (United States); Laget, J.M. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Mibe, T. [Ohio University, Athens, OH 45701 (United States); Qiang, Y. [Duke University, Durham, NC 27708 (United States); Stepanyan, S. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Tedeschi, D.J. [University of South Carolina, Columbia, SC 29208 (United States); Xu, W. [Massachusetts Institute of Technology, Cambridge, MA 02139-4307 (United States); Adhikari, K.P.; Amaryan, M. [Old Dominion University, Norfolk, VA 23529 (United States); Anghinolfi, M. [INFN, Sezione di Genova, 16146 Genova (Italy); Ball, J. [CEA, Centre de Saclay, Irfu/Service de Physique Nucleaire, 91191 Gif-sur-Yvette (France); Battaglieri, M. [INFN, Sezione di Genova, 16146 Genova (Italy); Batourine, V. [Thomas Jefferson National Accelerator Facility, Newport News, VA 23606 (United States); Bedlinskiy, I. [Institute of Theoretical and Experimental Physics, Moscow 117259 (Russian Federation); Bellis, M. [Carnegie Mellon University, Pittsburgh, PA 15213 (United States); Biselli, A.S. [Fairfield University, Fairfield, CT 06824 (United States); Carnegie Mellon University, Pittsburgh, PA 15213 (United States)

2011-02-07

We report the first, kinematically-complete measurement of the differential cross section of {phi}-meson photoproduction from deuterium near the production threshold for a proton using the CLAS detector and a tagged-photon beam in Hall B at Jefferson Lab. The measurement was carried out by a triple coincidence detection of a proton, K{sup +} and K{sup -} near the theoretical production threshold of 1.57 GeV. The extracted differential cross sections (d{sigma})/(dt) for the initial photon energy range of 1.65-1.75 GeV are consistent with predictions based on a quasifree mechanism. Our finding is different from recent LEPS results on {phi}-meson photoproduction from deuterium in a similar incident photon energy range, but in a different momentum transfer region.

Deuterium permeation and diffusion in high purity beryllium

International Nuclear Information System (INIS)

Abramov, E.

1990-05-01

The permeation rate of deuterium through high-purity beryllium membranes was measured using the gas-driven permeation technique. The time-dependent and the steady-state deuterium flux data were analyzed and the effective diffusivities of the samples were determined. A multilayer permeation theory was used in order to eliminate the surface oxide effects and the diffusion coefficients of the bulk beryllium were determined. The diffusion parameters obtained for the extra-grade beryllium samples (99.8%) are D 0 = 6.7 x 10 -9 [m 2 /s] and E D = 28.4 [KJ/mol]; and for the high-grade beryllium samples (99%) the parameters are D 0 = 8.0 x 10 -9 [m 2 /s] and E D = 35.1 [KJ/mol

Design and Fabrication of Titanium Target for Portable Neutron Generator

International Nuclear Information System (INIS)

Lee, Cheol Ho; Oh, Byunghoon; Chang, Daesik; Jang, Dohyun; In Sang Yeol; Park, Jaewon; Hong, Kwangpyo

2014-01-01

For the neutron generator to produce a neutron flux of the above order, a target that produces fast neutrons in the generator plays an important role, and the target is used and applied to develop the generator due to its simplicity and inexpensive. Making suitable targets for neutron production, especially mono-energy neutrons, has always been of interest. These targets have been used for neutron production reaction studies, calibration of detectors, and neutron therapy. Different studies have been carried out on deuterium and tritium for making solid targets to produce mono-energy neutron from D-D and D-T reactions. A lot of investigations have been carried out on solid target properties such as lifetime, thermal stability, neutron yield, and energy. Vaporized zirconium and titanium layers on a high thermal conductivity substrate (Cu, Mo, Ag) have been used as deuterium and tritium absorbing metals. The density of titanium is smaller than zirconium and the range of charged particles in the titanium targets is more than that in zirconium targets. Thus, titanium targets have more neutron yield than zirconium targets in a low energy beam and titanium is usually used to make a target. The titanium target was designed and simulated to determine the suitable thickness of the target. As a result of the simulation, the target was fabricated to generate fast neutrons by the reaction. The thickness of the target was measured using a profiler. The thickness of the two targets is 2.108 and 2.190 μm. The target will be applied to produce neutrons in a neutron generator

Tritium and deuterium as water tracers in hydrologic systems. Completion report

International Nuclear Information System (INIS)

Stewart, G.L.; Stetson, J.R.

1975-05-01

A study was conducted to evaluate the suitability of deuterium and tritium as tracers to depict water and pollutant movement in porous media. This involved studying the interaction of these tracers with soil materials and evaluating this interaction in terms of retardation in tracer flow velocity, compared to bulk water flow. Previous work had suggested that tritium and deuterium interact with soils and are removed from tracer solution during flow. The data presented clearly show that a tracing front becomes diluted in tracer during infiltration into oven-dried soil. There appears to be very little difference between the degree of tritium and deuterium interaction. The source of interaction is demonstrated to be primarily hydroxyl associated with the clay minerals. These exchange sites are destroyed by heating soil to 70C which eliminates tracer loss during infiltration

Reaction of ethane with deuterium over platinum(111) single-crystal surfaces

International Nuclear Information System (INIS)

Zaera, F.; Somorhai, G.A.

1985-01-01

Deuterium exchange and hydrogenolysis of ethane were studied over (111) platinum surfaces under atmospheric pressures and a temperature range of 475-625 K. Activation energies of 19 kcal/mol for exchange and 34 kcal/mol for hydrogenolysis were obtained. The exchange reaction rates displayed kinetic orders with respect to deuterium and ethane partial pressures of -0.55 and 1.2, respectively. The exchange production distribution was U-shaped, peaking at one and six deuterium atoms per ethane molecule, similar to results reported for other forms of platinum, e.g., supported, films, and foils. The pressure of ethylidyne moieties on the surface was inferred from low-energy electron diffraction and thermal desorption spectroscopy. A mechanism is proposed to explain the experimental results, in which ethylidyne constitutes an intermediate in one of two competitive pathways. 31 references, 9 figures, 3 tables

Biological effects of deuterium - depleted water

International Nuclear Information System (INIS)

Stefanescu, I.; Titescu, Gh.; Croitoru, Cornelia; Saros-Rogobete, Irina

2000-01-01

Deuterium-depleted water (DDW) is represented by water that has an isotopic content smaller than 145 ppm D/(D + H). DDW production technique consists in the separation of deuterium from water by a continuous distillation process under pressure of about 133.3 mbar. The water used as raw material has a isotopic content of 145 ppm D/(D + H) and can be demineralized water, distillated water or condensed-steam. DDW results as a distillate with an isotopic deuterium content of 15-80 ppm, depending on the level we want to achieve. Beginning with 1996 the Institute of Cryogenics and Isotopic Technologies, DDW producer, co-operated with Romanian specialized institutes for studying the biological effects of DDW. The role of naturally occurring D in living organisms was examined by using DDW instead of natural water. These investigations led to the following conclusions: - DDW caused a tendency towards the increase of the basal tone, accompanied by the intensification of the vasoconstrictor effects of phenylefrine, noradrenaline and angiotensin; the increase of the basal tone and vascular reactivity produced by the DDW persists after the removal of the vascular endothelium; - Animals treated with DDW showed an increase of the resistance both to sublethal and lethal gamma radiation doses, suggesting a radioprotective action by the stimulation of non-specific immune defense mechanisms; - DDW stimulates immuno-defense reactions represented by the opsonic, bactericidal and phagocyte capacity of the immune system together with an increase in the number of poly-morphonuclear neutrophils; - Investigations regarding artificial reproduction of fish with DDW fecundated solutions confirmed favorable influence in embryo growth stage and resistance and following growth stages; - It was studied germination, growth and quantitative character variability in plants; one can remark the favorable influence of DDW on biological processes in plants in various ontogenetic stages. (authors)

Origin of excess heat generated during loading Pd-impregnated alumina powder with deuterium and hydrogen

International Nuclear Information System (INIS)

Dmitriyeva, O.; Cantwell, R.; McConnell, M.; Moddel, G.

2012-01-01

Highlights: ► We studied heat produced by hydrogen and deuterium in Pd-impregnated alumina powder. ► Samples were fabricated using light and heavy water isotopes and varied the gas used for loading. ► Incorporation of hydrogen and deuterium influenced the amount of heat released or consumed. ► Pd nanoparticles appear to catalyze hydrogen/deuterium (H/D) exchange chemical reactions. ► Anomalous heating can be accounted for by chemical rather than nuclear reactions. - Abstract: We studied heat production in Pd-impregnated alumina powder in the presence of hydrogen and deuterium gases, investigating claims of anomalous heat generated as a result of nuclear fusion, usually referred to as a low energy nuclear reaction (LENR). By selecting the water isotope used to fabricate the material and then varying the gas used for loading, we were able to influence the amount of heat released or consumed. We suggest that Pd in its nanoparticle form catalyzes hydrogen/deuterium (H/D) exchange reactions in the material. This hypothesis is supported by heat measurements, residual gas analysis (RGA) data, and calculations of energy available from H/D exchange reactions. Based on the results we conclude that the origin of the anomalous heat generated during deuterium loading of Pd-enriched alumina powder is chemical rather than nuclear.

A Reexamination of Deuterium Fractionation on Mars

Science.gov (United States)

Pathare, A.; Paige, D. A.

1997-07-01

The ratio of deuterium to hydrogen in the Martian atmosphere is enhanced by a factor of 5 with respect to the terrestrial value, probably due to fractionation associated with thermal Jeans escape from the top of the atmosphere. Theoretical analyses of the relative efficiency of H and D escape have suggested that the deuterium enrichment implies Mars has outgassed the vast majority of its H2O and that the Martian atmosphere is presently not exchanging water with a juvenile reservoir. However, measurements of high and variable D/H values within hydrous minerals in SNC meteorites strongly suggest that mixing between the atmosphere and juvenile water has taken place. Furthermore, the lack of any observed enrichment of atmospheric (18) O with respect to (16) O, in spite of fractionating nonthermal escape mechanisms, indicates buffering by some juvenile source of oxygen, most probably in the form of a surface or subsurface reservoir of water. We propose that this apparent paradox in the interpretation of isotopic hydrogen and oxygen fractionation --or lack thereof-- can be resolved by re-examining the standard model of deuterium fractionation efficiency on Mars. Specifically, we demonstrate the importance of using upper atmospheric temperatures more representative of the range experienced by the Martian exosphere over the course of the solar cycle. Preliminary calculations involving changes in effusion velocity and diffusive separation as a function of exospheric temperature indicate that incorporating these more representative lower exospheric temperatures will reduce the relative efficiency of D escape, in which case the observed enrichment of deuterium can indeed result from exchange with a juvenile source of water. We are in the process of confirming these computations with a one-dimensional upper atmospheric photochemical model that considers the effects of changing solar activity and exospheric temperature on ionospheric composition. If our initial calculations are

Synthesis of deuterium-labeled plant sterols and analysis of their side-chain mobility by solid state deuterium NMR

International Nuclear Information System (INIS)

Marsan, M.P.; Muller, I.; Milon, A.

1996-01-01

Sitosterol and stigmasterol, plant sterols, were deuterated at specific positions. Orientation and mobility of the deuterated sitosterol and stigmasterol (and two of their diasteromers) on oriented lipid bilayers were analyzed by deuterium NMR spectroscopy. Orientation and mobility of the side chains was revealed by these studies

Deuterium pumping and erosion behavior of selected graphite materials under high flux plasma bombardment in PISCES

International Nuclear Information System (INIS)

Hirooka, Y.; Conn, R.W.; Goebel, D.M.; LaBombard, B.; Lehmer, R.; Leung, W.K.; Nygren, R.E.; Ra, Y.

1988-06-01

Deuterium plasma recycling and chemical erosion behavior of selected graphite materials have been investigated using the PISCES-A facility. These materials include: Pyro-graphite; 2D-graphite weave; 4D-graphite weave; and POCO-graphite. Deuterium plasma bombardment conditions are: fluxes around 7 /times/ 10 17 ions s/sup /minus/1/cm/sup /minus/2/; exposure time in the range from 10 to 100 s; bombarding energy of 300 eV; and graphite temperatures between 20 and 120/degree/C. To reduce deuterium plasma recycling, several approaches have been investigated. Erosion due to high-fluence helium plasma conditioning significantly increases the surface porosity of POCO-graphite and 4D-graphite weave whereas little change for 2D-graphite weave and Pyro-graphite. The increased pore openings and refreshed in-pore surface sites are found to reduce the deuterium plasma recycling and chemical erosion rates at transient stages. The steady state recycling rates for these graphite materials can be also correlated to the surface porosity. Surface topographical modification by machined-grooves noticeably reduces the steady state deuterium recycling rate and the impurity emission from the surface. These surface topography effects are attributed to co-deposition of remitted deuterium, chemically sputtered hydrocarbon and physically sputtered carbon under deuterium plasma bombardment. The co-deposited film is found to have a characteristic surface morphology with dendritic microstructures. 18 ref., 4 figs., 1 tab

Performance of the prototype LANL solid deuterium ultra-cold neutron source

CERN Document Server

Hill, R E; Bowles, T J; Greene, G L; Hogan, G; Lamoreaux, S; Marek, L; Mortenson, R; Morris, C L; Saunders, A; Seestrom, S J; Teasdale, W A; Hoedl, S; Liu, C Y; Smith, D A; Young, A; Filippone, B W; Hua, J; Ito, T; Pasyuk, E A; Geltenbort, P; García, A; Fujikawa, B; Baessler, S; Serebrov, A

2000-01-01

A prototype of a solid deuterium (SD sub 2) source of Ultra-Cold Neutrons (UCN) is currently being tested at LANSCE. The source is contained within an assembly consisting of a 4 K polyethylene moderator surrounded by a 77 K beryllium flux trap in which is embedded a spallation target. Time-of-flight measurements have been made of the cold neutron spectrum emerging directly from the flux trap assembly. A comparison is presented of these measurements with results of Monte Carlo (LAHET/MCNP) calculations of the cold neutron fluxes produced in the prototype assembly by a beam of 800 MeV protons incident on the tungsten target. A UCN detector was coupled to the assembly through a guide system with a critical velocity of 8 m/s ( sup 5 sup 8 Ni). The rates and time-of-flight data from this detector are compared with calculated values. Measurements of UCN production as a function of SD sub 2 volume (thickness) are compared with predicted values. The dependence of UCN production on SD sub 2 temperature and proton beam...

Low temperature internal friction in pure iron charged with hydrogen or deuterium

International Nuclear Information System (INIS)

Moser, P.; Dufresne, J.F.; Ritchie, I.G.

1977-01-01

The search for the elusive hydrogen Snoek-peak in pure iron has been continued with specimens charged with either hydrogen or deuterium. The peaks observed are attributed to deformation produced during charging and can be classified as an α-type peak and a Snoek-Koester type peak. The detailed behavior of these peaks during systematic outgassing of hydrogen or deuterium is described

Determination of dew absorption by coffee plant through deuterium concentrations in leaf water

Energy Technology Data Exchange (ETDEWEB)

Leopoldo, P R [Faculdade de Ciencias Medicas e Biologicas de Botucatu (Brazil); Salati, E; Matsui, E [Centro de Energia Nuclear na Agricultura, Piracicaba (Brazil)

1975-12-01

The effect of dew falling on leaves on the water metabolism of the coffee plant (Coffea arabica) is examined. The use of natural stable isotopes variations in plant physiological studies is demonstrated. Water extracted from leaf samples is analysed by mass spectrometry. Analyses of deuterium concentrations in water extracted from plant leaves, dew and nutrient solutions are made. Determination of changes in deuterium concentration in the water of leaves from plants exposed to dew, compared with leaves not exposed to dew, is carried out. Results show that during daytime there is an enrichment in deuterium in water contained in the leaves, while at night the opposite occurs.

Determination of dew absorption by coffee plant through deuterium concentrations in leaf water

International Nuclear Information System (INIS)

Leopoldo, P.R.; Salati, E.; Matsui, E.

1975-01-01

The effect of dew falling on leaves on the water metabolism of the coffee plant (Coffea arabica) is examined. The use of natural stable isotopes variations in plant physiological studies is demonstrated. Water extracted from leaf samples is analysed by mass spectrometry. Analyses of deuterium concentrations in water extracted from plant leaves, dew and nutrient solutions are made. Determination of changes in deuterium concentration in the water of leaves from plants exposed to dew, compared with leaves not exposed to dew, is carried out. Results show that during daytime there is an enrichment in deuterium in water contained in the leaves, while at night the opposite occurs [pt

Temperature dependence of deuterium retention mechanisms in tungsten

Energy Technology Data Exchange (ETDEWEB)

Roszell, J.P. [University of Toronto Institute for Aerospace Studies, 4925 Dufferin Street, Toronto, Ontario, M3H 5T6 (Canada); Davis, J.W., E-mail: jwdavis@starfire.utias.utoronto.ca [University of Toronto Institute for Aerospace Studies, 4925 Dufferin Street, Toronto, Ontario, M3H 5T6 (Canada); Haasz, A.A. [University of Toronto Institute for Aerospace Studies, 4925 Dufferin Street, Toronto, Ontario, M3H 5T6 (Canada)

2012-10-15

The retention of 500 eV D{sup +} was measured as a function of implantation temperature in single- (SCW) and poly-crystalline (PCW) tungsten. The results show a decrease in retention of {approx}2 orders of magnitude over the temperature range of 350-550 K in SCW and a decrease of an order of magnitude over the temperature range of 600-700 K in PCW. Inspection of the TDS spectra showed a shift in peak location from 600 to 800 K as temperature was increased above 350 K in SCW and above 450 K in PCW specimens. TMAP modeling showed that the change in peak location corresponds to a change in trapping energy from 1.3 eV for the 600 K peak to 2.1 eV for the 800 K peak. It is proposed that for implantations performed above 350 K in SCW and 450 K in PCW, deuterium-containing vacancies are able to diffuse and combine to create stable nano-bubbles within the crystal lattice. The formation of nano-bubbles due to the annihilation of deuterium-vacancy complexes results in a change in the trapping energy from 1.3 to 2.1 eV as well as a decrease in retention as some of the deuterium-vacancy complexes will be destroyed at surfaces or grain boundaries, decreasing the number of trapping sites available.

Temperature dependence of deuterium retention mechanisms in tungsten

International Nuclear Information System (INIS)

Roszell, J.P.; Davis, J.W.; Haasz, A.A.

2012-01-01

The retention of 500 eV D + was measured as a function of implantation temperature in single- (SCW) and poly-crystalline (PCW) tungsten. The results show a decrease in retention of ∼2 orders of magnitude over the temperature range of 350–550 K in SCW and a decrease of an order of magnitude over the temperature range of 600–700 K in PCW. Inspection of the TDS spectra showed a shift in peak location from 600 to 800 K as temperature was increased above 350 K in SCW and above 450 K in PCW specimens. TMAP modeling showed that the change in peak location corresponds to a change in trapping energy from 1.3 eV for the 600 K peak to 2.1 eV for the 800 K peak. It is proposed that for implantations performed above 350 K in SCW and 450 K in PCW, deuterium-containing vacancies are able to diffuse and combine to create stable nano-bubbles within the crystal lattice. The formation of nano-bubbles due to the annihilation of deuterium-vacancy complexes results in a change in the trapping energy from 1.3 to 2.1 eV as well as a decrease in retention as some of the deuterium-vacancy complexes will be destroyed at surfaces or grain boundaries, decreasing the number of trapping sites available.

Temperature dependence of deuterium retention mechanisms in tungsten

Science.gov (United States)

Roszell, J. P.; Davis, J. W.; Haasz, A. A.

2012-10-01

The retention of 500 eV D+ was measured as a function of implantation temperature in single- (SCW) and poly-crystalline (PCW) tungsten. The results show a decrease in retention of ˜2 orders of magnitude over the temperature range of 350-550 K in SCW and a decrease of an order of magnitude over the temperature range of 600-700 K in PCW. Inspection of the TDS spectra showed a shift in peak location from 600 to 800 K as temperature was increased above 350 K in SCW and above 450 K in PCW specimens. TMAP modeling showed that the change in peak location corresponds to a change in trapping energy from 1.3 eV for the 600 K peak to 2.1 eV for the 800 K peak. It is proposed that for implantations performed above 350 K in SCW and 450 K in PCW, deuterium-containing vacancies are able to diffuse and combine to create stable nano-bubbles within the crystal lattice. The formation of nano-bubbles due to the annihilation of deuterium-vacancy complexes results in a change in the trapping energy from 1.3 to 2.1 eV as well as a decrease in retention as some of the deuterium-vacancy complexes will be destroyed at surfaces or grain boundaries, decreasing the number of trapping sites available.

Quasi-elastic interactions and one-pion production by neutrinos and anti-neutrinos on a deuterium target

International Nuclear Information System (INIS)

Barlag, S.J.M.

1984-01-01

In this thesis, the weak charged current interactions of neutrinos and antineutrinos with nucleons are described, in which the neutrino scatters in a quasi-elastic way with the nucleon, leaving an excited nucleon state. The experiments have been performed in the bubble chamber BEBC, filled with deuterium and exposed to the CERN Wide Band (anti-)neutrino beams. This gave the opportunity to study both interactions on protons and on neutrons separately, whereas the measurement of the exclusive channels could be performed with a high precision. After a short introduction of the relevant theories (standard model; QCD; one-pion production models; FKR quark model), the experimental set-up at CERN is described as well as the bubble chamber picture facility in Amsterdam. Next, results of the neutrino and antineutrino experiments are given followed by a comparison with theory. (Auth.)

The use of deuterium in medicine

International Nuclear Information System (INIS)

Roth, E.; Sutton, J.; Marsac, J.

1981-03-01

Whenever a corporal function experiences a disturbance reflected either by changes in metabolic activity or modifications of the importance of pools of certain molecules the possibility exists of making use of isotopes in diagnosis. This paper discusses the use of deuterium to measure total body water and extravascular water in the lungs, and gives examples of clinical applications

Laboratory facility for production of cryogenic targets for hot plasma experiments

International Nuclear Information System (INIS)

Sadowski, M.; Szydlowski, A.; Jakubowski, L.; Cwiek, E.

1990-10-01

Results of preliminary operational tests of the cryogenic stand designed for the production of small droplets of liquid hydrogen or deuterium are presented. Such cryogenic micro-targets are needed for nuclear and thermonuclear experiments. (author)

Physics and technology of superthin internal targets in storage rings

International Nuclear Information System (INIS)

Popov, S.G.

1989-01-01

The new generation of accelerators for coincidence electronuclear investigations is discussed. The luminosity and beam parameters are calculated for an electron storage ring with an internal target operating in the superthin regime. The advantages and disadvantages in comparison with conventional operation using an external beam and target are described. The intermediate results for 2 GeV electron scattering on polarized internal deuterium target are given (joint Novosibirsk-Argonne experiment). 32 refs.; 5 figs

Measurement of gluconeogenesis using glucose fragments and mass spectrometry after ingestion of deuterium oxide

NARCIS (Netherlands)

Chacko, Shaji K.; Sunehag, Agneta L.; Sharma, Susan; Sauer, Pieter J. J.; Haymond, Morey W.

We report a new method to measure the fraction of glucose derived from gluconeogenesis using gas chromatography-mass spectrometry and positive chemical ionization. After ingestion of deuterium oxide by subjects, glucose derived from gluconeogenesis is labeled with deuterium. Our calculations of

Thermal desorption of deuterium from modified carbon nanotubes and its correlation to the microstructure

NARCIS (Netherlands)

Lisowski, W.F.; Keim, Enrico G.; van den Berg, A.H.J.; Smithers, Mark A.; Smithers, M.A.

2006-01-01

The process of deuterium desorption from single-wall carbon nanotubes (SWNTs) modified by atomic (D) and molecular (D2) deuterium treatment was investigated in an ultrahigh vacuum environment using thermal desorption mass spectroscopy (TDMS). Microstructural and chemical analyses of SWNT material,

Monte Carlo simulation of explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator.

Science.gov (United States)

Bergaoui, K; Reguigui, N; Gary, C K; Brown, C; Cremer, J T; Vainionpaa, J H; Piestrup, M A

2014-12-01

An explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator has been simulated using the Monte Carlo N-Particle Transport Code (MCNP5). Nuclear-based explosive detection methods can detect explosives by identifying their elemental components, especially nitrogen. Thermal neutron capture reactions have been used for detecting prompt gamma emission (10.82MeV) following radiative neutron capture by (14)N nuclei. The explosive detection system was built based on a fully high-voltage-shielded, axial D-D neutron generator with a radio frequency (RF) driven ion source and nominal yield of about 10(10) fast neutrons per second (E=2.5MeV). Polyethylene and paraffin were used as moderators with borated polyethylene and lead as neutron and gamma ray shielding, respectively. The shape and the thickness of the moderators and shields are optimized to produce the highest thermal neutron flux at the position of the explosive and the minimum total dose at the outer surfaces of the explosive detection system walls. In addition, simulation of the response functions of NaI, BGO, and LaBr3-based γ-ray detectors to different explosives is described. Copyright © 2014 Elsevier Ltd. All rights reserved.

Characterization of deuterium retention and co-deposition of fuel with lithium on the divertor tile of EAST using laser induced breakdown spectroscopy

International Nuclear Information System (INIS)

Li, Cong; Zhao, Dongye; Hu, Zhenhua; Wu, Xingwei; Luo, Guang-Nan; Hu, Jiansheng; Ding, Hongbin

2015-01-01

A laser induced breakdown spectroscopy (LIBS) system has been developed to measure and monitor the composition evolution on plasma facing materials (PFMs) of Experimental Advanced Superconducting Tokamak (EAST). As a necessity and important proof of principle experiment, LIBS analysis has been performed for lithium–deuterium co-deposition layer diagnosis of EAST divertor tiles in lab experiments. The distribution of deuterium retention has been obtained from the depth of 0.5–4 μm in the divertor tiles. The deuterium/hydrogen concentration ratio was estimated as 0.17 ± 0.02 in lithium–deuterium co-deposition layer. Moreover, the depth profile behaviors of lithium and deuterium indicate that the deuterium retention in divertor tile came from lithium–deuterium co-deposition processes during deuterium discharge in EAST. This work would improve the understanding of deuterium retention and lithium–deuterium co-deposition mechanism and give a guidance to optimize the LIBS system which will be a unique and useful diagnostic approach in EAST 2014-campaign

Correction factor to determine total hydrogen+deuterium concentration obtained by inert gas fusion-thermal conductivity detection (IGF- TCD) technique

International Nuclear Information System (INIS)

Ramakumar, K.L.; Sesha Sayi, Y.; Shankaran, P.S.; Chhapru, G.C; Yadav, C.S.; Venugopal, V.

2004-01-01

The limitation of commercially available dedicated equipment based on Inert Gas Fusion- Thermal Conductivity Detection (IGF - TCD) for the determination of hydrogen+deuterium is described. For a given molar concentration, deuterium is underestimated vis a vis hydrogen because of lower thermal conductivity and not considering its molecular weight in calculations. An empirical correction factor based on the differences between the thermal conductivities of hydrogen, deuterium and the carrier gas argon, and the mole fraction of deuterium in the sample has been derived to correct the observed hydrogen+deuterium concentration. The corrected results obtained by IGF - TCD technique have been validated by determining hydrogen and deuterium contents in a few samples using an independent method based on hot vacuum extraction-quadrupole mass spectrometry (HVE-QMS). Knowledge of mole fraction of deuterium (XD) is necessary to effect the correction. The correction becomes insignificant at low X D values (XD < 0.2) as the precision in the IGF measurements is comparable with the extent of correction. (author)

Synthesis of optically pure deuterium-labelled nicotine, nornicotine and cotinine

International Nuclear Information System (INIS)

Jacob, P. III; Benowitz, N.L.; Shulgin, A.T.; California Univ., San Francisco

1988-01-01

We describe methods for the synthesis of enantiomerically pure (S)-nicotine-3',3'-d 2 , (S)-nornicotine-3',3-d 2 , and (S)-cotinine-4',4'-d 2 . The key intermediate was 5-bromomyosmine, which underwent base catalyzed exchange with deuterium oxide to give 5-bromomyosmine-3',3'- d 2 with >99% incorporation of label. This intermediate was reduced to (±)-5-bromo-nornicotine-3',3'-d 2 with sodium borohydride, resolved, and converted to (S)-nornicotine-3',3'-d(sub)2 by reductive debromination with hydrogen and a palladium catalyst. Reductive alkylation with formaldehyde and sodium borohydride provided (S)-nicotine-3',3'-d 2 , which was converted to (S)-cotinine-4',4'-d 2 by reaction with bromine followed by zinc reduction. The deuterium label is located at positions that are not attacked in the major routes of mammalian metabolism of these alkaloids. Syntheses of tetradeuterated analogs of nicotine and cotinine and a pentadeuterated analog of nicotine, in which additional deuterium atoms are incorporated in the methyl groups, are also reported. (author)

Measurement of gluconeogenesis using glucose fragments and mass spectrometry after ingestion of deuterium oxide.

Science.gov (United States)

We report a new method to measure the fraction of glucose derived from gluconeogenesis using gas chromatography-mass spectrometry and positive chemical ionization. After ingestion of deuterium oxide by subjects, glucose derived from gluconeogenesis is labeled with deuterium. Our calculations of gluc...

Origin of excess heat generated during loading Pd-impregnated alumina powder with deuterium and hydrogen

Energy Technology Data Exchange (ETDEWEB)

Dmitriyeva, O., E-mail: olga.dmitriyeva@colorado.edu [Department of Electrical, Computer, and Energy Engineering, University of Colorado, Boulder, CO 80309-0425 (United States); Coolescence LLC, 2450 Central Ave Ste F, Boulder, CO 80301 (United States); Cantwell, R.; McConnell, M. [Coolescence LLC, 2450 Central Ave Ste F, Boulder, CO 80301 (United States); Moddel, G. [Department of Electrical, Computer, and Energy Engineering, University of Colorado, Boulder, CO 80309-0425 (United States)

2012-09-10

Highlights: Black-Right-Pointing-Pointer We studied heat produced by hydrogen and deuterium in Pd-impregnated alumina powder. Black-Right-Pointing-Pointer Samples were fabricated using light and heavy water isotopes and varied the gas used for loading. Black-Right-Pointing-Pointer Incorporation of hydrogen and deuterium influenced the amount of heat released or consumed. Black-Right-Pointing-Pointer Pd nanoparticles appear to catalyze hydrogen/deuterium (H/D) exchange chemical reactions. Black-Right-Pointing-Pointer Anomalous heating can be accounted for by chemical rather than nuclear reactions. - Abstract: We studied heat production in Pd-impregnated alumina powder in the presence of hydrogen and deuterium gases, investigating claims of anomalous heat generated as a result of nuclear fusion, usually referred to as a low energy nuclear reaction (LENR). By selecting the water isotope used to fabricate the material and then varying the gas used for loading, we were able to influence the amount of heat released or consumed. We suggest that Pd in its nanoparticle form catalyzes hydrogen/deuterium (H/D) exchange reactions in the material. This hypothesis is supported by heat measurements, residual gas analysis (RGA) data, and calculations of energy available from H/D exchange reactions. Based on the results we conclude that the origin of the anomalous heat generated during deuterium loading of Pd-enriched alumina powder is chemical rather than nuclear.

Study of liquid hydrogen and liquid deuterium cold neutron sources; Etude de sources de neutrons froids a hydrogene et deuterium liquides

Energy Technology Data Exchange (ETDEWEB)

Harig, H D [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1967-12-01

In view of the plant of the cold neutron source for a high flux reactor (maximal thermal flux of about 10{sup 15} n/cm{sup 2}s) an experimental study of several cold sources of liquid hydrogen and liquid deuterium has been made in a low power reactor (100 kW, about 10{sup 12} n/cm{sup 2}s). We have investigated: -cold neutron sources of liquid hydrogen shaped as annular layers of different thickness. Normal liquid hydrogen was used as well as hydrogen with a high para-percentage. -Cold neutron sources of liquid deuterium in cylinders of 18 and 38 cm diameter. In this case the sources could be placed into different positions to the reactor core within the heavy water reflector. This report gives a general description of the experimental device and deals more detailed with the design of the cryogenic systems. Then, the measured results are communicated, interpreted and finally compared with those of a theoretical study about the same cold moderators which have been the matter of the experimental investigation. (authors) [French] En vue de l'installation d'une source a neutrons froids dans un reacteur a haut flux (flux thermique maximal environ 10{sup 15} n/cm{sup 2}s), nous avons fait une etude neutronique experimentale de differentes sources froides a hydrogene et a deuterium liquides aupres d'un reacteur a faible puissance (100 kW environ 10{sup 12} n/cm{sup 2}s). Nous avons etudie: des couches annulaires de differentes epaisseurs d'hydrogene liquide normal et d'hydrogene a grand pourcentage para, des cellules cylindriques de 18 et 38 cm de diametre, remplies de deuterium liquide et placees a differentes positions dans le reflecteur D{sub 2}O. Ce travail traite l'implantation de l'installation cryogenique et donne une description generale de l'experience. L'interpretation des resultats fait etat entre autres d'une comparaison entre l'experience et une etude theorique portant sur les memes moderateurs. (auteurs)

Neutron yield in experiments with Z-pinches in frozen deuterium filaments

International Nuclear Information System (INIS)

Meierovich, B.E.; Sukhorukov, S.T.

1991-01-01

Experiments on the properties of the neutron yield and stability of dense Z-pinches in frozen deuterium filaments two years ago have still not received a proper explanation. A discharge in a dielectric deuterium filament differs qualitatively in its behavior from one in a metal conductor. The authors assert attempts to interpret the experiment have not taken this fact properly into account. The enhanced stability and substantial neutron yield do not follow from the classical picture of a Bennett equilibrium in the current channel. The most important experimental characteristic of a discharge in frozen deuterium is the dependence of the neutron yield on the current strength at a given stage. The spread in the experimental points is quite large so one naturally prefers t describe the experimental data by means of a physically simple model and not go to a full-scale simulation of all the processes. When the deuterium is fully ionized the electron drift velocity is smaller than the thermal velocity, enabling calculation of the neutron yield by means of a self-similar model of the Z-pinch compression which treats electron degeneracy. To find the neutron yield it suffices to consider only the first half-period of the self-similar oscillations including the state of maximum compression. The subsequent evolution of the current channel, which is associated with radial expansion, does not contribute significantly to the neutron yield

Study of the ionization rate of the released deuterium in vacuum arc discharges with metal deuteride cathodes

Science.gov (United States)

Liu, Fei-Xiang; Long, Ji-Dong; Zheng, Le; Dong, Pan; Li, Chen; Chen, Wei

2018-02-01

The ionization rate of the released deuterium from a metal deuteride cathode in vacuum arc discharges is investigated by both experiments and modeling analysis. Experimental results show that the deuterium ionization rate increases from 2% to 30% with the increasing arc current in the range of 2-100 A. Thus the full ionization assumption, as is widely used in arc plasma simulations, is not satisfied for the released deuterium at low discharge current. According to the modeling results, the neutral-to-ion conversion efficiency for the deuterium traveling across the cathodic spot region can be significantly less than one, due to the fast plasma expansion and rarefaction in the vacuum. In addition, the model also reveals that, unlike the metal atoms which are mainly ionized in the sheath region and flow back to the cathode, the deuterium ionization primarily occurs in the quasi-neutral region and moves towards the anode. Consequently, the cathodic sheath layer acts like a filter that increases the deuterium fraction beyond the sheath region.

Cold versus hot fusion deuterium branching ratios

International Nuclear Information System (INIS)

Fox, H.; Bass, R.

1995-01-01

A major source of misunderstanding of the nature of cold nuclear fusion has been the expectation that the deuterium branching ratios occurring within a palladium lattice would be consistent with the gas-plasma branching ratios. This misunderstanding has led to the concept of the dead graduate student, the 1989's feverish but fruitless search for neutron emissions from cold fusion reactors, and the follow-on condemnation of the new science of cold fusion. The experimental facts are that in a properly loaded palladium lattice, the deuterium fusion produces neutrons at little above background, a greatly less-than-expected production of tritium (the tritium desert), and substantially more helium-4 than is observed in hot plasma physics. The experimental evidence is now compelling (800 reports of success from 30 countries) that cold nuclear fusion is a reality, that the branching ratios are unexpected, and that a new science is struggling to be recognized. Commercialization of some types of cold fusion devices has already begun

Deuterium transport and trapping in polycrystalline tungsten

International Nuclear Information System (INIS)

Anderl, R.A.; Holland, D.F.; Longhurst, G.R.; Pawelko, R.J.; Trybus, C.L.; Sellers, C.H.

1992-01-01

This paper reports that deuterium permeation studies for polycrystalline tungsten foil have been conducted to provide data for estimating tritium transport and trapping in tungsten-clad divertors proposed for advanced fusion-reactor concepts. Based on a detailed transmission electron microscopy (TEM) microstructural characterization of the specimen material and on analyses of permeation data measured at temperatures ranging form 610 to 823 K for unannealed and annealed tungsten foil (25 μm thick), the authors note the following key results: deuterium transport in tungsten foil is dominated by extensive trapping that varies inversely with prior anneal temperatures of the foil material, the reduction in the trapped fraction correlates with a corresponding elimination of a high density of dislocations in cell-wall structures introduced during the foil fabrication process, trapping behavior in these foils can be modelled using trap energies between 1.3 eV and 1.5 eV and trap densities ranging from 1 x 10 -5 atom fraction

Deuterium-depleted water. Short history and news

International Nuclear Information System (INIS)

Stefanescu, Ioan; Tamaian, Radu; Titescu, Gheorghe

2002-01-01

Deuterium-depleted water represents water that has an isotopic content lower than 144 ppm D/(D+H) which is the natural isotopic content of water. DDW is a non-toxic product. Knowing that deuterium content of water has a significant influence on living organisms, since 1996 NIR-DCIT ICSTI at Rm. Valcea cooperated with Romanian specialized instititutes for biological effects' evaluation of DDW. The investigations lead to the conclusion that DDW caused a tendency towards the increase of the basal tone, accompanied by the intensification of the vasoconstrictor effects. Animals teated with DDW showed an increase of the resistance both to sub lethal and to lethal gamma radiation doses. DDW stimulates immune defense reactions. Investigations regarding artificial reproduction of fish with DDW fecundated solutions confirmed favorable influence in embryo growth stage and resistance in next growth stages. One can remark the favourable influence of DDW on biological process in plants in various ontogenetic stages. (authors)

DYNAMIC DEUTERIUM ENRICHMENT IN COMETARY WATER VIA ELEY–RIDEAL REACTIONS

Energy Technology Data Exchange (ETDEWEB)

Yao, Yunxi; Giapis, Konstantinos P., E-mail: giapis@cheme.caltech.edu [Division of Chemistry and Chemical Engineering, California Institute of Technology, Pasadena, California 91125 (United States)

2017-01-20

The deuterium-to-hydrogen ratio (D/H) in water found in the coma of Jupiter family comet (JFC) 67P/Churyumov–Gerasimenko was reported to be (5.3 ± 0.7) × 10{sup −4}, the highest among comets and three times the value for other JFCs with an ocean-like ratio. This discrepancy suggests the diverse origins of JFCs and clouds the issue of the origin of Earth’s oceanic water. Here we demonstrate that Eley–Rideal reactions between accelerated water ions and deuterated cometary surface analogs can lead to instantaneous deuterium enrichment in water scattered from the surface. The reaction proceeds with H{sub 2}O{sup +} abstracting adsorbed D atoms, forming an excited H{sub 2}DO* state, which dissociates subsequently to produce energetic HDO. Hydronium ions are also produced readily by the abstraction of H atoms, consistent with H{sub 3}O{sup +} detection and abundance in various comets. Experiments with water isotopologs and kinematic analysis on deuterated platinum surfaces confirmed the dynamic abstraction mechanism. The instantaneous fractionation process is independent of the surface temperature and may operate on the surface of cometary nuclei or dust grains, composed of deuterium-rich silicates and carbonaceous chondrites. The requisite energetic water ions have been detected in the coma of 67P in two populations. This dynamic fractionation process may temporarily increase the water D/H ratio, especially as the comet gets closer to the Sun. The magnitude of the effect depends on the water ion energy-flux and the deuterium content of the exposed cometary surfaces.

Characterization of physical and chemical properties of QLARIVIA-line of deuterium depleted Water

International Nuclear Information System (INIS)

Ferdes, Ov. S.; Mladin, C.; Petre, R.M.; Mitu, F.; Costinel, Diana; Vremera, Raluca; Sandru, Claudia

2008-01-01

QLARIVIA is the brand-name of Deuterium Depleted Water line of products of drinking water differentiating mainly by the deuterium concentration. It is the result of a national technological transfer project and it is based on an original, patented technology for deuterium depletion from the normal water. The paper presents the measuring and analysis results of the chemical and physical properties of the QLARIVIA brand-line of drinking DDW, as: pH; water hardness; permanganate index; Ca; Mg; Cl - ; SO4 2 - ; NH 4 ; NO 3 - ; NO 2 - , as well as the deuterium concentration determination by mass spectrometry. The analysis has been performed on at least 20 batch-samples, by usual, standardized and/or validated analytical methods, in ISO 17025:2005 accredited laboratories. The results are discussed considering the requirements of the EU directive on drinking water as well as of the Romanian Act on drinking water no. 458/2002 with its supplemental modification by the Act no.363/2004. The conclusion is that QLARIVIA - brand line of drinking DDW fulfills all the official physical and chemical requirements for the drinking water. (authors)

Process for the preparation of deuterium enriched water in the production of hydrogen

International Nuclear Information System (INIS)

Mandrin, Ch.

1986-01-01

A synthesis gas facility is operated for n consecutive periods. During the first period excess feed water is added to the facility. The effluent from the resulting mixture is fed to a storage container. During the following n-1 operating periods the stored effluent water is used as feed for the synthesis gas facility. The effluent from each operating period is stored in layers with corresponding deuterium concentration in the storage container. The effluent from the last operating period involving the highest deuterium concentration is fed to a second container and from there to a heavy water production unit. In order to recuperate the deuterium contained in the gas mixture leaving the condensor (consisting of hydrogen, vapour and residual compounds), the mixture is fed to an exchange stage. There the mixture is isotopically exchanged with additional water in a cross flow whereby this water gets enriched in deuterium and is fed to the synthesis gas facility. The process leads to an improved yield of heavy water in the heavy water production facility

Requirements on internal targets for the Aladdin storage ring

International Nuclear Information System (INIS)

Holt, R.J.

1984-01-01

The feasibility of performing electron scattering experiments with polarized targets in electron storage rings is explored by considering an electron-deuteron scattering experiment at the Aladdin storage ring. It is noted that this new method is compatible with recent proposals for linac-stretcher-ring accelerator designs. A new method for producing a polarized hydrogen or deuterium target is proposed and some preliminary results are described. 21 references, 6 figures, 1 table

Transport of recycled deuterium to the plasma core in TFTR

International Nuclear Information System (INIS)

Skinner, C.H.; Bell, M.G.; Budny, R.V.; Jassby, D.L.; Park, H.; Ramsey, A.T.; Stotler, D.P.; Strachan, J.D.

1997-10-01

The authors report a study of the fueling of the plasma core by recycling in the Tokamak Fusion Test Reactor (TFTR). They have analyzed discharges fueled by deuterium recycled from the limiter and tritium-only neutral beam injection. In these plasmas, the DT neutron rate provides a measure of the deuterium influx into the core plasma. They find a reduced influx with plasmas using lithium pellet conditioning and with plasmas of reduced major (and minor) radius. Modeling with the DEGAS neutrals code shows that the dependence on radius can be related to the penetration of neutrals through the scrape-off layer

Changes in bacterial radiation sensitivity due to deuterium substitution

International Nuclear Information System (INIS)

Strauss, A.; Weiss, H.

1985-01-01

The influence of deuterium substitution for hydrogen on radiation sensitivity was measured under various conditions for E. coli B/r irradiated by 450 kev electrons in single intense pulses. Cells were grown in a nutrient medium made from a deuterium oxide based solution. They were suspended in a D/sub 2/O based buffered saline and plated in thin aqueous layers on membrane filters and irradiated in 100% N/sub 2/ or 100% O/sub 2/. Comparisons were made to cells similarly plated and irradiated but grown instead in a water based nutrient medium and suspended in either a water based or a D/sub 2/O based buffered saline. For the conventionally grown cells, D/sub 2/O increased the radiation sensitivity in both gases by about 10%. For cells grown and suspended with D/sub 2/O based media, a 50% reduction of radiation sensitivity was found with both gas and an increased extrapolation number was observed. In this latter method, deuterium is more fully substituted for hydrogen in the molecular substrate of the cell. These cells were also irradiated over a temperature range of 2 0 C to 43 0 C after being suspended in deuterated ethanol. Speculations for the changes induced by the substitution are presented

Biosynthesis of DIMBOA in maize using deuterium oxide as a tracer

International Nuclear Information System (INIS)

Peng, S.; Chilton, W.S.

1994-01-01

Growth of root cultures and of shoot cultures of maize (Zea mays) was noticeably inhibited by 30% D2O in liquid medium. Increasing the concentration of D2O in the medium decreased the concentration of DIMBOA [2,4-dihydroxy-7-methoxy 2H-1,4-benzoxazin-3(4H)-one] and the biomass of roots and shoots. DIMBOA was converted to MBOA [6-methoxy-2(3H)-benzoxazolone] and analysed by mass spectroscopy. Both root cultures and shoot cultures grown on 30% D2O incorporated deuterium at non-exchangeable sites of MBOA (15.6% and 16.1%, respectively), indicating that maize roots and shoots are independently capable of synthesizing DIMBOA from carbohydrate precursors. EI-MS and H-1 NMR showed that there was little selectivity in deuterium labelling between hydrogens at aromatic position 4, 5 or 7, consistent with the major amount of deuterium incorporation occurring prior to synthesis of shikimic acid

Thermal desorption of deuterium from polycrystalline nickel pre-implanted with helium

International Nuclear Information System (INIS)

Shi, S.Q.; Abramov, E.; Thompson, D.A.

1990-01-01

The thermal desorption technique has been used to study the trapping of deuterium atoms in high-purity polycrystalline nickel pre-implanted with helium for 1 x 10 19 to 5 x 10 20 ions/m 2 . The effect of post-implantation annealing at 703 K and 923 K on the desorption behavior was investigated. Measured values of the total amount of detrapped deuterium (Q T ) and helium concentration were used in a computer simulation of the desorption curve. It was found that the simulation using one or two discrete trap energies resulted in an inadequate fit between the simulated and the measured data. Both experimental and simulation results are explained using a stress-field trapping model. The effective binding energy, E b eff , was estimated to be in the range of 0.4-0.6 eV. Deuterium charging was found to stimulate a release of helium at a relatively low temperature

Synthesis of deuterium labeled ketamine metabolite dehydronorketamine-d₄.

Science.gov (United States)

Sulake, Rohidas S; Chen, Chinpiao; Lin, Huei-Ru; Lua, Ahai-Chang

2011-10-01

A convenient synthesis of ketamine metabolite dehydronorketamine-d(4), starting from commercially available deuterium labeled bromochlorobenzene, was achieved. Key steps include Grignard reaction, regioselective hydroxybromination, Staudinger reduction, and dehydrohalogenation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reactor prospects of muon-catalyzed fusion of deuterium and tritium concentrated in transition metals

International Nuclear Information System (INIS)

Stacey, W.M. Jr.

1989-01-01

It is conjectured that the number of fusion events catalyzed by a single muon is orders of magnitude greater for deuterium and tritium concentrated in a transition metal than in gaseous form and that the recent observation of 2.5-MeV neutrons from a D 2 O electrolytic cell with palladium and titanium cathodes can thereby be interpreted in terms of cosmic muon-catalyzed deuterium-deuterium fusion. This suggests a new fusion reactor reactor consisting of deuterium and tritium concentrated in transition metal fuel elements in a fusion core that surrounds an accelerator-produced muon source. The feasibility of net energy production in such a reactor is established in terms of requirements on the number of fusion events catalyzed per muon. The technological implications for a power reactor based on this concept are examined. The potential of such a concept as a neutron source for materials testing and tritium and plutonium production is briefly discussed

The effects of environmental deuterium on normal and neoplastic cultured cell development

International Nuclear Information System (INIS)

Bild, W.; Schuller, T.; Zhihai, Qin; Blankenstein, T.; Nastasa, V.; Haulica, I.

2000-01-01

The powdered culture media (RPMI - 1640) were reconstituted either with normal distilled water (150 ppm deuterium) either with deuterium - depleted water (DDW) in various concentrations (30, 60, 90 ppm) and sterilized by filtration with 0.2 μm filters. The cell lines used were NIH (normal mouse fibroblasts), RAG (mouse renal carcinoma) and TS/A (mouse mammary adenocarcinoma). In auxiliary tests, BAIBC mouse splenocytes in direct culture were used, stimulated for growth with concanavalin A or LPS (bacterial lipopolysaccharide). The estimation of the growth was made using the MTT assay or direct counting with trypan blue exclusion. The following results were obtained: Deuterium - depleted water had a stimulating effect on cell growth, the most important stimulating action being from the 90 ppm deuterium-water. The growth curves show, in a first phase, a stimulation of the rapid -growing neoplastic cells, followed by a slower growth of the normal cells. Amiloride 100 mM blocking of the Na + /K + membrane pump did not affect the cell growth curves, while the lansoprazole 100 mM blocking of the K + /H + ATP-ase brought the growth curves at the level of those with normal water. This might show an eventual involvement of the K + /H + antiport in the stimulating effects of the DDW. (authors)

Explanation od sudden temperature dependence of muon catalysis in solid deuterium

CERN Document Server

Gershtejn, S S

2001-01-01

It is indicated, that the elastic scattering of the d mu-meson atoms in the solid deuterium at sufficiently low temperatures (as well as of slow neutrons) occurs on the whole crystalline lattice practically without energy loss, and the inelastic collision with the phonon excitation is low.Therefore, the resonance formation of the dd mu-molecules in the solid deuterium takes place before the d mu mesoatoms thermalization and it explains practically observed independence of the dd mu-molecules formation rate and muon catalysis of the temperatures

Activity-regulating structural changes and autoantibody epitopes in transglutaminase 2 assessed by hydrogen/deuterium exchange

DEFF Research Database (Denmark)

Iversen, Rasmus; Mysling, Simon; Hnida, Kathrin

2014-01-01

The multifunctional enzyme transglutaminase 2 (TG2) is the target of autoantibodies in the gluten-sensitive enteropathy celiac disease. In addition, the enzyme is responsible for deamidation of gluten peptides, which are subsequently targeted by T cells. To understand the regulation of TG2 activity...... and the enzyme's role as an autoantigen in celiac disease, we have addressed structural properties of TG2 in solution by using hydrogen/deuterium exchange monitored by mass spectrometry. We demonstrate that Ca(2+) binding, which is necessary for TG2 activity, induces structural changes in the catalytic core...... domain of the enzyme. Cysteine oxidation was found to abolish these changes, suggesting a mechanism whereby disulfide bond formation inactivates the enzyme. Further, by using TG2-specific human monoclonal antibodies generated from intestinal plasma cells of celiac disease patients, we observed...

Hyperfine structure of S-states of muonic deuterium

Directory of Open Access Journals (Sweden)

Alexey P. Martynenko

2015-09-01

Full Text Available On the basis of quasipotential method in quantum electrodynamics we calculate corrections of order $\\alpha^5$ and $\\alpha^6$ to hyperfine structure of $S$-wave energy levels of muonic deuterium. Relativistic corrections, effects of vacuum polarization in first, second and third orders of perturbation theory, nuclear structure and recoil corrections are taken into account. The obtained numerical values of hyperfine splitting $\\Delta E^{hfs}(1S=50.2814$ meV ($1S$ state and $\\Delta E^{hfs}(2S=6.2804$ meV ($2S$ state represent reliable estimate for a comparison with forthcoming experimental data of CREMA collaboration. The hyperfine structure interval $\\Delta_{12}=8\\Delta E^{hfs}(2S- \\Delta E^{hfs}(1S=-0.0379$ meV can be used for precision check of quantum electrodynamics prediction for muonic deuterium.

Warm water deuterium fractionation in IRAS 16293-2422

DEFF Research Database (Denmark)

Persson, Magnus Vilhelm; Jørgensen, Jes Kristian; van Dishoeck, E. F.

2013-01-01

observations reveal the physical and chemical structure of water vapor close to the protostars on solar-system scales. The red-shifted absorption detected toward source B is indicative of infall. The excitation temperature is consistent with the picture of water ice evaporation close to the protostar. The low......Context. Measuring the water deuterium fractionation in the inner warm regions of low-mass protostars has so far been hampered by poor angular resolution obtainable with single-dish ground- and space-based telescopes. Observations of water isotopologues using (sub)millimeter wavelength...... interferometers have the potential to shed light on this matter. Aims: To measure the water deuterium fractionation in the warm gas of the deeply-embedded protostellar binary IRAS 16293-2422. Methods: Observations toward IRAS 16293-2422 of the 53,2 - 44,1 transition of H218O at 692.07914 GHz from Atacama Large...

Activation analysis for LHD experiments with deuterium gases

International Nuclear Information System (INIS)

Nishimura, Kiyohiko; Yamanishi, Hirokuni; Komori, Akio; Hayashi, Katsumi

2008-01-01

Identification of radionuclides obtained from deuterium experiments and evaluation of dose rate level were performed on the structural materials of the Large Helical Device and the Experimental Hall. Energies of neutron sources are 2.45 MeV (D-D reaction) and 14 MeV (D-T reaction). Neutron fluence was calculated using the two-dimensional transport code DOT-3.5. Generation of radionuclides was calculated using the CINAC code. Radionuclides of 93m Nb, 63 Ni, and 60 Co for helical coils, 55 Fe and 60 Co for stainless steel, 55 Fe, 60 Co, and 93m Nb for poloidal coils, and 40 K and 55 Fe for floor concrete were dominant after a series of experiments with deuterium gases. Evaluation of dose rate level for the structural materials and air were performed taking into account a current experimental schedule. (author)

Deuterium retention in molten salt electrodeposition tungsten coatings

International Nuclear Information System (INIS)

Zhou, Hai-Shan; Xu, Yu-Ping; Sun, Ning-Bo; Zhang, Ying-Chun; Oya, Yasuhisa; Zhao, Ming-Zhong; Mao, Hong-Min; Ding, Fang; Liu, Feng; Luo, Guang-Nan

2016-01-01

Highlights: • We investigate D retention in electrodeposition W coatings. • W coatings are exposed to D plasmas in the EAST tokamak. • A cathodic current density dependence on D retention is found. • Electrodeposition W exhibits lower D retention than VPS-W. - Abstract: Molten salt electrodeposition is a promising technology to manufacture the first wall of a fusion reactor. Deuterium (D) retention behavior in molten salt electrodeposition tungsten (W) coatings has been investigated by D-plasma exposure in the EAST tokamak and D-ion implantation in an ion beam facility. Tokamak exposure experiments demonstrate that coatings prepared with lower current density exhibit less D retention and milder surface damage. Deuterium-ion implantation experiments indicate the D retention in the molten salt electrodeposition W is less than that in vacuum plasma spraying W and polycrystalline W.

Deuterium retention in molten salt electrodeposition tungsten coatings

Energy Technology Data Exchange (ETDEWEB)

Zhou, Hai-Shan [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Xu, Yu-Ping [Science Island Branch of Graduate School, University of Science and Technology of China, Hefei (China); Sun, Ning-Bo; Zhang, Ying-Chun [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing (China); Oya, Yasuhisa [Radioscience Research Laboratory, Faculty of Science, Shizuoka University, Shizuoka (Japan); Zhao, Ming-Zhong [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Mao, Hong-Min [Science Island Branch of Graduate School, University of Science and Technology of China, Hefei (China); Ding, Fang; Liu, Feng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Luo, Guang-Nan, E-mail: gnluo@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Science Island Branch of Graduate School, University of Science and Technology of China, Hefei (China); Hefei Center for Physical Science and Technology, Hefei (China); Hefei Science Center of Chinese Academy of Science, Hefei (China)

2016-12-15

Highlights: • We investigate D retention in electrodeposition W coatings. • W coatings are exposed to D plasmas in the EAST tokamak. • A cathodic current density dependence on D retention is found. • Electrodeposition W exhibits lower D retention than VPS-W. - Abstract: Molten salt electrodeposition is a promising technology to manufacture the first wall of a fusion reactor. Deuterium (D) retention behavior in molten salt electrodeposition tungsten (W) coatings has been investigated by D-plasma exposure in the EAST tokamak and D-ion implantation in an ion beam facility. Tokamak exposure experiments demonstrate that coatings prepared with lower current density exhibit less D retention and milder surface damage. Deuterium-ion implantation experiments indicate the D retention in the molten salt electrodeposition W is less than that in vacuum plasma spraying W and polycrystalline W.

Total cross section results for deuterium electrodisintegration

International Nuclear Information System (INIS)

Skopik, D.M.; Murphy, J.J. II; Shin, Y.M.

1976-01-01

Theoretical total cross sections for deuterium electrodisintegration are presented as a function of incident electron energy. The cross section has been calculated using virtual photon theory with Partovi's photodisintegration calculation for E/subx/ > 10 MeV and effective range theory for E/subx/ 2 H(e, n) reaction in Tokamak reactors

Measuring deuterium permeation through tungsten near room temperature under plasma loading using a getter layer and ion-beam based detection

Directory of Open Access Journals (Sweden)

Stefan Kapser

2017-08-01

Full Text Available A method to measure deuterium permeation through tungsten near room temperature under plasma loading is presented. The permeating deuterium is accumulated in a getter layer of zirconium, titanium or erbium, respectively, on the unexposed side of the sample. Subsequently, the amount of deuterium in the getter is measured ex-situ using nuclear reaction analysis. A cover layer system on the getter prevents direct loading of the getter with deuterium from the gas phase during plasma loading. In addition, it enables the distinction of deuterium in the getter and at the cover surface. The method appears promising to add additional permeation measurement capabilities to deuterium retention experiments, also in other plasma devices, without the need for a complex in-situ permeation measurement setup.

Synthesis of deuterium labelled ibuprofen

International Nuclear Information System (INIS)

Cappon, V.J.; Halstead, G.W.; Theis, D.L.

1986-01-01

The preparations of [ar- 2 H 4 ]-ibuprofen and [ar, 3,3,3- 2 H 7 ]-ibuprofen are described. The deuterium was incorporated into the aromatic ring of [ar- 2 H 4 ]-ibuprofen which is a metabolically stable position. [ar, 3,3,3- 2 H 7 ]-ibuprofen was synthesized by the same route using [ 2 H 3 ]-CH 3 I instead of CH 3 I for use as a GC/MS internal standard in stable isotope labelled bioavailability studies. (author)

Growth acceleration and photosynthesis of the scenedesmus algae and cocconeis algae in deuterium water

International Nuclear Information System (INIS)

Liu Feng; Wang Wenqing

1998-01-01

In order to find new way to treat the radioactive tritium waste water, scenedesmus algae and cocconeis algae are cultured in medium which contains 30% (w) deuterium water. During different time, activities of photosymthesis, absorption spectrum, growth rate and low-temperature fluorescence spectrum are measured. Accelerated growth is found in the deuterium water compared to the normal water. Activities of photosynthesis show the similar result (F v /F m ) to the growth data. It is also concluded from low-temperature fluorescence spectra that algae activities in the deuterium water, which are expressed by PS I/PS II, are more sensitive than those in the normal water

The influence of variation of deuterium's concentration on the immunity system

International Nuclear Information System (INIS)

Tamaian, Radu

2007-01-01

Hydrogen's substitution by deuterium represents an environmental alteration at which the organism (in vivo) and the cells (in vitro), respectively, if they can't accommodate will recede. In this way the variations of deuterium's isotopic abundance can be compared with the environmental factors of stress (variations of temperature, quantity of nourishment, radiations, etc). As different forms of existence of life are more or less sensitive at environment's factors variations, so they respond in different ways to concentration variations of deuterium from the living environment/organism. Consequently the mammals' immunity system (IS) presents different feed-backs. The main results are stressed as follows: - a. The use as alimentary adjuvant of deuterium depleted water (DDW) in prolonged periods (21 days) increased the capacity of unspecific immunity defense against the specific bacterial aggression, both in Gram-positive bacteria (Streptococcus pneumoniae558) and of Gram-negative (Klebsiella pneumoniae507); - b. The immunosuppression determined by cyclophosphamide-alquilant agent with medullary depletion of white series reduced the survival of inoculated animals, even in the conditions in which the animals have received dietary supplement with DDW; - c. The immunosuppression through medullary depletion due to irradiation reduced also the survival of inoculated animals, even in the conditions in which the animals have received dietary supplement with DDW. Those mentioned herein lead to the hypothesis that prolonged administration of DDW simulates the unspecific immunity defence, probably through the stimulation of the hematogenic marrow and of lymphopoietic and granulopoietic stem cells. (author)

Measurement of the deuterium Balmer series line emission on EAST

Energy Technology Data Exchange (ETDEWEB)

Wu, C. R.; Xu, Z.; Jin, Z.; Zhang, P. F. [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, Anhui 230031 (China); Science Island Branch of Graduate School, University of Science and Technology of China, Hefei, Anhui 230031 (China); Huang, J., E-mail: juan.huang@ipp.ac.cn; Gao, W.; Gao, W.; Chang, J. F.; Xu, J. C.; Duan, Y. M.; Chen, Y. J.; Zhang, L.; Wu, Z. W.; Li, J. G. [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, Anhui 230031 (China); Hou, Y. M. [Institute of Plasma Physics, Chinese Academy of Sciences, P.O. Box 1126, Hefei, Anhui 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2016-11-15

Volume recombination plays an important role towards plasma detachment for magnetically confined fusion devices. High quantum number states of the Balmer series of deuterium are used to study recombination. On EAST (Experimental Advanced Superconducting Tokamak), two visible spectroscopic measurements are applied for the upper/lower divertor with 13 channels, respectively. Both systems are coupled with Princeton Instruments ProEM EMCCD 1024B camera: one is equipped on an Acton SP2750 spectrometer, which has a high spectral resolution ∼0.0049 nm with 2400 gr/mm grating to measure the D{sub α}(H{sub α}) spectral line and with 1200 gr/mm grating to measure deuterium molecular Fulcher band emissions and another is equipped on IsoPlane SCT320 using 600 gr/mm to measure high-n Balmer series emission lines, allowing us to study volume recombination on EAST and to obtain the related line averaged plasma parameters (T{sub e}, n{sub e}) during EAST detached phases. This paper will present the details of the measurements and the characteristics of deuterium Balmer series line emissions during density ramp-up L-mode USN plasma on EAST.

Creatine Supplementation Increases Total Body Water in Soccer Players: a Deuterium Oxide Dilution Study.

Science.gov (United States)

Deminice, R; Rosa, F T; Pfrimer, K; Ferrioli, E; Jordao, A A; Freitas, E

2016-02-01

This study aimed to evaluate changes in total body water (TBW) in soccer athletes using a deuterium oxide dilution method and bioelectrical impedance (BIA) formulas after 7 days of creatine supplementation. In a double-blind controlled manner, 13 healthy (under-20) soccer players were divided randomly in 2 supplementation groups: Placebo (Pla, n=6) and creatine supplementation (CR, n=7). Before and after the supplementation period (0.3 g/kg/d during 7 days), TBW was determined by deuterium oxide dilution and BIA methods. 7 days of creatine supplementation lead to a large increase in TBW (2.3±1.0 L) determined by deuterium oxide dilution, and a small but significant increase in total body weight (1.0±0.4 kg) in Cr group compared to Pla. The Pla group did not experience any significant changes in TBW or body weight. Although 5 of 6 BIA equations were sensitive to determine TBW changes induced by creatine supplementation, the Kushner et al. 16 method presented the best concordance levels when compared to deuterium dilution method. In conclusion, 7-days of creatine supplementation increased TBW determined by deuterium oxide dilution or BIA formulas. BIA can be useful to determine TBW changes promoted by creatine supplementation in soccer athletes, with special concern for formula choice. © Georg Thieme Verlag KG Stuttgart · New York.

The study of the deuterium isotopic fractionation through the cell membrane of the plant

International Nuclear Information System (INIS)

Berdea, P.; Cuna, Stela; Deliu, C.

2002-01-01

The purpose of this study is to prove that there is a water deuterium isotope fractionation when the water passes through the cell membrane. The carrots (Daucus carota) were grown in vitro in a Murashige and Skoog mineral-salt medium and have been exposed to a water solution with a uniform isotopic content. After seven days the cell culture was filtered and the cell water was vacuum extracted. The water from aqueous solution and the cell water were analyzed for hydrogen by isotope ratio mass spectrometry. The procedure was repeated for 14 and 21 day old cell cultures. The measurements have revealed a water deuterium isotopic fractionation between extra-cellular water and cellular water. The deuterium content was found to be higher within the cells by 10 o / oo for non-embryonic cells and 13 o / oo for the embryonic cells. This fractionation is a non-evaporative fractionation between intracellular and extra-cellular water and it represents a new step in the overall fractionation of deuterium water in the plants. The existence of such isotopic fractionation through the cell membrane implies that the relationship between the deuterium content of cellulose nitrate in plant and meteoric water should be revised. Also, this finding is of interest for understanding the balance and dynamics of the hydrogen isotopes in the environment. (authors)

Production of secondary Deuterium in the atmosphere at various latitudes

Energy Technology Data Exchange (ETDEWEB)

Papini, P. [Florence Univ. (Italy)]|[INFN, Florence (Italy); Grimani, C. [Perugia Univ. (Italy)]|[INFN, Perugia (Italy); Stephens, S.A. [Tata Institute of Fundamental Research, Bombay (International Commission on Radiation Units and Measurements)

1995-09-01

Secondary deuterium in the atmosphere are produced in interactions by primary cosmic rays. The shape of their energy spectrum depends on the primary cosmic ray spectrum incident at the top of the atmosphere. At high energies, the spectral shape depends on the primary spectrum of helium and heavy nuclei. However, at very low energies, specially below the geomagnetic cut-off, the spectral shape depends on the evaporation and recoil processes and hence almost independent of the spectral shape of the primary radiation. It is undertaken a calculation of the secondary deuterium spectrum at small atmospheric depths at various latitudes and the results will be presented.

Atmospheric influence on the deuterium excess signal in polar firn - implications for ice core interpretation

NARCIS (Netherlands)

Schlosser, Elisabeth; Oerter, H.; Masson-Delmotte, V.; Reijmer, C.H.

2008-01-01

The seasonal deuterium excess signal of fresh snow samples from Neumayer station, coastal Dronning Maud Land, Antarctica, was studied to investigate the relationship between deuterium excess and precipitation origin. An isotope model was combined with a trajectory model to determine the relative

Nuclear micro-beam analysis of deuterium distribution in carbon fibre composites for controlled fusion devices

International Nuclear Information System (INIS)

Petersson, P.; Kreter, A.; Possnert, G.; Rubel, M.

2010-01-01

Probes made of carbon fibre composite NB41 were exposed to deuterium plasmas in the TEXTOR tokamak and in a simulator of plasma-wall interactions, PISCES. The aim was to assess the deuterium retention and its lateral and depth distribution. The analysis was performed by means of D( 3 He, p) 4 He and 12 C( 3 He, p) 14 N nuclear reactions analysis using a standard (1 mm spot) and micro-beam (20 μm resolution). The measurements have revealed non uniform distribution of deuterium atoms in micro-regions: differences by a factor of 3 between the maximum and minimum deuterium concentrations. The differences were associated with the orientation and type of fibres for samples exposed in PICSES. For surface structure in the erosion zone of samples exposed to a tokamak plasma the micro-regions were more complex. Depth profiling has indicated migration of fuel into the bulk of materials.

Analysis technique of impurity in high purity deuterium by cryogenic gas-chromatography

International Nuclear Information System (INIS)

Zhou Junbo; Gao Liping

2007-01-01

A veracious and applicable quantitative analysis method of O 2 , N 2 and H 2 , HD in high purity deuterium by the chromatogram columniation filled with 5A molecular sieve and alumina was researched and constituted at natural temperature and 77 K, respectively. Minimum detecting limit of the present method is (150-200) x 10 -6 for H 2 and HD, and it can meet the need of quantitative analysis of the impurity during high purity deuterium preparation. (authors)

Phonons in Solid Hydrogen and Deuterium Studied by Inelastic Coherent Neutron Scattering

DEFF Research Database (Denmark)

Nielsen, Mourits

1973-01-01

Phonon dispersion relations have been measured by coherent neutron scattering in solid para-hydrogen and ortho-deuterium. The phonon energies are found to be nearly equal in the two solids, the highest energy in each case lying close to 10 meV. The pressure and temperature dependence of the phonon...... energies have been measured in ortho-deuterium and the lattice change determined by neutron diffraction. When a pressure of 275 bar is applied, the phonon energies are increased by about 10%, and heating the crystal to near the melting point decreases them by about 7%. The densities of states, the specific...... heats, and the Debye temperatures have been deduced and found to be in agreement with the published experimental results. The Debye temperatures are 118 K for hydrogen and 114 K for deuterium. For hydrogen the Debye-Waller factor has been measured by incoherent neutron scattering and it corresponds...

Isotope effect and deuterium excess parameter revolution in ice and snow melt

International Nuclear Information System (INIS)

Yin Guan; Ni Shijun; Fan Xiao; Wu Hao

2003-01-01

The change of water isotope composition actually is a integrated reaction depending on the change of environment. The ice and snow melt of different seasons in high mountain can obviously influence the change of isotope composition and deuterium excess parameter of surface flow and shallow groundwater. To know the isotopic fractionation caused by this special natural background, explore its forming and evolvement, is unusually important for estimating, the relationship between the environment, climate and water resources in an area. Taking the example of isotope composition of surface flow and shallow groundwater in Daocheng, Sichuan, this paper mainly introduced the changing law of isotope composition and deuterium excess parameter of surface flow and hot-spring on conditions of ice and snow melt with different seasons in high mountain; emphatically discussed the isotope effect and deuterium excess parameter revolution in the process of ice and snow melting and its reason. (authors)

Blister/hole formation on tungsten surface due to low-energy and high-flux deuterium/helium plasma exposures

International Nuclear Information System (INIS)

Nishijima, D.; Iwakiri, H.; Yoshida, N.; Ye, M.Y.; Ohno, N.; Takamura, S.

2005-01-01

Deuterium/helium plasma exposures on tungsten surface bring serious damages such as blister and hole. Blistering occurs by cleaving along layered structure intrinsic to the press-roll manufacturing process. Mechanical polishing and helium pre-exposure on mirror-finished powder metallurgy tungsten drastically suppress blister formation. Small cracks made by a polishing would become paths to the surface for diffusing deuterium atoms in the substrate, resulting in no gas accumulation and no blister formation on the surface. Helium pre-exposure would make a helium-enriched layer near the surface, which becomes a kind of diffusion barrier for incident deuterium atoms. Blister formation and deuterium retention are suppressed on the surface with helium-enriched layer. (author)

Investigation of detached recombining deuterium plasma and carbon chemical erosion in the toroidal divertor simulator NAGDIS-T

International Nuclear Information System (INIS)

Yada, K.; Matsui, N.; Ohno, N.; Kajita, S.; Takamura, S.; Takagi, M.

2009-01-01

Detached deuterium recombining plasma has been generated in the toroidal divertor simulator. The electron temperature (0.1-0.4 eV) and density (∼10 18 m -3 ) in the detached plasmas were evaluated with a spectroscopic method using a series of deuterium Balmer line emission from highly excited levels and the Stark broadening of D(2-12). We have investigated the role of volume plasma recombination through Electron-Ion Recombination (EIR) and Molecular Activated Recombination (MAR) processes. Moreover, the carbon erosion in the detached deuterium plasma has been studied with a weight loss method. It is found that deuterium neutrals generated by EIR process could have strong influence on the carbon chemical erosion.

On line determination of deuterium in hydrogen water exchange reaction by mass spectrometry. IRP-10

International Nuclear Information System (INIS)

Sharma, J.D.; Alphonse, K.P.; Mishra, Sushama; Prabhu, S.A.; Mohan, Sadhana; Tangri, V.K.

2007-01-01

The Deuterium (D)/Hydrogen (H) analysis at low Concentration is generally carried out by Mass Spectrometry. Mass Spectrometer is specially designed for the measurement of Mass 2 and 3 ratio. The Deuterium analysis of water and hydrogen in concentration range of a few ppm to about 1% plays an important role in the Heavy Water Production Plants. For the enrichment of the Deuterium concentration in H 2 O by H 2 - H 2 O exchange a catalyst is essential as reaction is relatively slow. Heavy Water Division has developed in house Platinum based catalyst for the isotopic exchange of Hydrogen and Water

Modelling third harmonic ion cyclotron acceleration of deuterium beams for JET fusion product studies experiments

DEFF Research Database (Denmark)

Schneider, M.; Johnson, T.; Dumont, R.

2016-01-01

Recent JET experiments have been dedicated to the studies of fusion reactions between deuterium (D) and Helium-3 (3He) ions using neutral beam injection (NBI) in synergy with third harmonic ion cyclotron radio-frequency heating (ICRH) of the beam. This scenario generates a fast ion deuterium tail...... enhancing DD and D3He fusion reactions. Modelling and measuring the fast deuterium tail accurately is essential for quantifying the fusion products. This paper presents the modelling of the D distribution function resulting from the NBI+ICRF heating scheme, reinforced by a comparison with dedicated JET fast...

Cytology is advanced by studying effects of deuterium environment

Science.gov (United States)

Bose, S.; Crespi, H. L.; Flaumenhaft, E.; Katz, J. J.

1967-01-01

Research of deuterium effects on biological systems shows deuteriation is not incompatible with life. With the successful cultivation of deuteriated bacteria, work is now being done on extraction of deuterio-compounds from bacteria.

Change of deuterium volume content in heavy water during carbon dioxide dissolution in it

International Nuclear Information System (INIS)

Efimova, T.I.; Kapitanov, V.F.; Levchenko, G.V.

1985-01-01

Carbon dioxide solution density in heavy water at increased temperature and pressure is measured and the influence of carbon dioxide solubility in heavy water on volumetric content of deuterium in it is determined. Investigations were conducted in the temperature range of 303-473 K and pressure range of 3-20 MPa by the autoclave method. Volumetric content of deuterium in heavy water decreases sufficiently with CO 2 dissolved in it in comparison with pure D 2 O under the similar conditions, and this decrease becomes more sufficient with the pressure increase. With the temperature increase the volumetric content of deuterium both for heavy water and for saturated carbon solution in heavy water decreases

The production of hadrons in the muon scattering on deuterium and xenon nuclei at 480 GeV

International Nuclear Information System (INIS)

Soeldner-Rembold, S.

1992-10-01

For the present thesis the hadronic final states of 6309 muon-deuterium events and 2064 muon-xenon events in the kinematical range Q 2 >1 (GeV/c) 2 , x>0.002, 0.1 3.5 mrad were studied. The multiplicity distributions of the muon-deuterium events and the muon-xenon events were described by means of the negative binomial distribution in intervals of the c.m. energy W. The two parameters anti n (mean multiplicity) and 1/k show for the muon-deuterium events a linear dependence on ln W 2 . The mean multiplicity anti n on xenon (anti n=10.43±0.19) is distinctly higher than on deuterium (anti n=7.76±0.07). The rapidity distributions of the positively charged and the negatively charged hadrons from muon-deuterium events are very well described by the Monte-Carlo program LUND. In the two-particle rapidity correlation both short-range and long-range correlations can be detected. The two-particle rapidity correlation in the xenon data are different from the deuterium data in the backward range. This difference indicates that the intranuclear cascade takes place in a limited range of small rapidities - relatively independently on the residual fragmentation process. (orig.) [de

Spin polarized deuterium

International Nuclear Information System (INIS)

Glyde, H.R.; Hernadi, S.I.

1986-01-01

Several ground state properties of (electron) spin-polarized deuterium (D) such as the energy, single quasiparticle energies and lifetimes, Landau parameters and sound velocities are evaluated. The calculations begin with the Kolos-Wolneiwicz potential and use the Galitskii-FeynmanHartree-Fock (GFHF) approximation. The deuteron nucleas has spin I = 1, and spin states I/sub z/ = 1,0,-1. We explore D 1 , D 2 and D 3 in which, respectively, one spin state only is populated, two states are equally populated, and three states are equally populated. We find the GFHF describes D 1 well, but D 2 and D 3 less well. The Landau parameters, F/sub L/, are small compared to liquid 3 He and very small for doubly polarized D 1 (i.e. the F/sub L/ decrease with nuclear polarization)

Synthesis of seven deuteromethyl-caffeine analogues observation of deuterium isotope effects on CMR analysis

Energy Technology Data Exchange (ETDEWEB)

Falconnet, J.B.; Brazier, J.L.; Desage, M.

1986-03-01

The synthesis of all 7 N-trideuteromethyl isotopomers of caffeine by reaction of trideuteromethyl iodide (C/sup 2/H/sub 3/I) with the appropriate xanthine molecules is described. The use of proton, deuterium and carbon-13-NMR as a first step in purity assessment revealed /sup 13/C-NMR deuterium isotope effects on the resonance of perdeuteromethyl carbons.

Holographic interferometry of isolated deuterium plasmas produced by a CO2 laser

International Nuclear Information System (INIS)

Gatenby, P.V.; Walker, A.C.

1978-10-01

The application of double exposure fractional fringe holographic interferometry to measurements of electron density in a plasma generated by irradiation of a freely falling pellet of solid deuterium with a focused CO 2 laser pulse is discussed. A particularly simple technique is used for processing and reconstructing the holograms and this is described in detail. A summary and discussion of the results is included with the emphasis on the observed evolution of the deuterium plasma over the duration of the laser irradiation. (author)

Synthesis of deuterium-labelled compounds for FOTEK project; Syntese af deuterium-maerkede forbindelser til FOeTEK projektet

Energy Technology Data Exchange (ETDEWEB)

Joergensen, O.; Egsgaard, H.; Larsen, E. [Forskningscenter Risoe, Roskilde (Denmark)

1996-06-01

In the FoTech project there have been utilized labelled compounds of stable isotopes as internal standards. Some of these compounds are commercially available ({sup 13}C-labelled PCB congeners, {sup 13}C-labelled diethylstilbestrol for determination of anabolic steroids). Others, like D{sub 9}-clenbuterol, D{sub 3}-clenbuterol, D{sub 3}-zeramol and D{sub 3}-dimetridazol have been synthesized. General aspects of deuterium compounds labelling are considered. (EG).

Hydrogen--deuterium exchange in saturated hydrocarbons on α-chromia catalyst

International Nuclear Information System (INIS)

Kalman, J.; Guczi, L.

1977-01-01

The kinetics of hydrogen--deuterium exchange in methane, ethane, and propane have been studied with unsupported α-chromia as catalyst in the temperature range of 598 to 688 0 K. The apparent activation energies for methane, ethane, and propane are 88, 130, and 84 kJ mol -1 , respectively, similar to those found on chromia gel. The order of reaction with respect to hydrocarbons and deuterium has been determined as also having the kinetic isotope effect. The main initial products are CH 3 D and CD 4 with methane, C 2 H 4 D 2 and C 2 D 6 with ethane, and C 3 H 7 D and C 3 D 8 with propane. A change in product distribution as a function of temperature, conversion, aging, and oxygen--deuterium treatment has been observed. In agreement with the kinetic data and the effect of oxygen, Cr 3+ has been assumed as the active species of the chromia catalyst, whereas Cr 2+ is an inactive site on the surface. There is no direct proof that chromium ion in a valence state higher than 3+ plays an important role in the exchange reaction. It was established that dual Cr 3+ -- Cr 3+ sites are responsible for the formation of ethane-d 2 . After a long deuterium treatment the number of dual sites is decreased, the effect being revealed in the decreased rate of exchange and the small amount of ethane-d 2 . On the contrary, the formation of methane-d 4 is interpreted by the formation of Cr = C bonds by analogy with homogeneous complexes. In the case of propane, the exchange reaction can be adequately interpreted by a π-allyl mechanism

Considerations related to the deuterium-depleted water isotopic analysis for an industrial production pilot plant

International Nuclear Information System (INIS)

Varlam, Mihai; Steflea, Dumitru; Irimescu, Rodica

2000-01-01

In the last few years, there is a major interest related to the use of Deuterium Depleted Water (DDW) for biological and medical purposes. Therefore, a production installation for DDW was developed and now, it is working in our Institute. The deuterium isotopic concentration for the final product is in the 10 - 40 ppm D / (D + H) range depending on customers' requirements. In order to control and manage the production process and also to validate the final product, a special procedure for deuterium content measurement for DDW by Isotopic Ratio Mass Spectrometry was developed. The main instrumentation is a MAT 250 IRMS with a hydrogen preparation line based on the zinc reduction process. The first concern regarding the analysis procedure for these water samples with very low deuterium concentration has been related to the preparation of an internal standard with a D / (D + H) isotopic value in the measurement range. For this raison, a distinct procedure was developed and applied, so that starting to the well-known VSMOW standard and so, a sequence of 12 samples with decreasing deuterium content was obtained. These samples were measured and 3 / 2 ratio mass signals versus 2 mass signal were plotted and statistically analyzed. Obviously, for each measurement, a H 3+ correction factor was calculated and applied, as a results of an entire statistically elimination procedure and by extrapolation of the linear curve plotted, a value for the primary DDW was determined. Other important problem related to deuterium content determination was to minimize the H 3+ factor correction. As the deuterium content is very low the contribution of this factor to the 3 mass signal becomes very important. Therefore, special operations were developed, considering the behaviour of linear dependence between 3 / 2 mass signal versus 2 mass signal in the lower part. Finally, special attention was given to estimate the lower isotopic concentration analysis limit. (authors)

Vertical distribution of deuterium in atmospheric water vapour: problems in application to assess atmospheric condensation models

International Nuclear Information System (INIS)

Taylor, C.B.

1984-01-01

The paper assesses the use of the author's data by Rozanski and Sonntag to support a multi-box model of the vertical distribution of deuterium in atmospheric water vapour, in which exchange between vapour and falling precipitation produces a steeper deuterium concentration profile than simpler condensation models. The mean deuterium/altitude profile adopted by Rozanski and Sonntag for this purpose is only one of several very different mean profiles obtainable from the data by arbitrary selection and weighting procedures; although it can be made to match the specified multi-box model calculations for deuterium, there is a wide discrepancy between the actual and model mean mixing ratio profiles which cannot be ignored. Taken together, the mixing ratio and deuterium profiles indicate that mean vapour of the middle troposphere has been subjected to condensation at greater heights and lower temperatures than those considered in the model calculations. When this is taken into account, the data actually fit much better to the simpler condensation models. But the vapour samples represent meteorological situations too remote in time from primary precipitation events to permit definite conclusions on cloud system mechanisms. (Auth.)

Cryogenic tritium-hydrogen-deuterium and deuterium-tritium layer implosions with high density carbon ablators in near-vacuum hohlraums

International Nuclear Information System (INIS)

Meezan, N. B.; Hopkins, L. F. Berzak; Pape, S. Le; Divol, L.; MacKinnon, A. J.; Döppner, T.; Ho, D. D.; Jones, O. S.; Khan, S. F.; Ma, T.; Milovich, J. L.; Pak, A. E.; Ross, J. S.; Thomas, C. A.; Benedetti, L. R.; Bradley, D. K.; Celliers, P. M.; Clark, D. S.; Field, J. E.; Haan, S. W.

2015-01-01

High Density Carbon (or diamond) is a promising ablator material for use in near-vacuum hohlraums, as its high density allows for ignition designs with laser pulse durations of <10 ns. A series of Inertial Confinement Fusion (ICF) experiments in 2013 on the National Ignition Facility [Moses et al., Phys. Plasmas 16, 041006 (2009)] culminated in a deuterium-tritium (DT) layered implosion driven by a 6.8 ns, 2-shock laser pulse. This paper describes these experiments and comparisons with ICF design code simulations. Backlit radiography of a tritium-hydrogen-deuterium (THD) layered capsule demonstrated an ablator implosion velocity of 385 km/s with a slightly oblate hot spot shape. Other diagnostics suggested an asymmetric compressed fuel layer. A streak camera-based hot spot self-emission diagnostic (SPIDER) showed a double-peaked history of the capsule self-emission. Simulations suggest that this is a signature of low quality hot spot formation. Changes to the laser pulse and pointing for a subsequent DT implosion resulted in a higher temperature, prolate hot spot and a thermonuclear yield of 1.8 × 10 15 neutrons, 40% of the 1D simulated yield

Cryogenic tritium-hydrogen-deuterium and deuterium-tritium layer implosions with high density carbon ablators in near-vacuum hohlraums

Energy Technology Data Exchange (ETDEWEB)

Meezan, N. B., E-mail: meezan1@llnl.gov; Hopkins, L. F. Berzak; Pape, S. Le; Divol, L.; MacKinnon, A. J.; Döppner, T.; Ho, D. D.; Jones, O. S.; Khan, S. F.; Ma, T.; Milovich, J. L.; Pak, A. E.; Ross, J. S.; Thomas, C. A.; Benedetti, L. R.; Bradley, D. K.; Celliers, P. M.; Clark, D. S.; Field, J. E.; Haan, S. W. [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, California 94551-0808 (United States); and others

2015-06-15

High Density Carbon (or diamond) is a promising ablator material for use in near-vacuum hohlraums, as its high density allows for ignition designs with laser pulse durations of <10 ns. A series of Inertial Confinement Fusion (ICF) experiments in 2013 on the National Ignition Facility [Moses et al., Phys. Plasmas 16, 041006 (2009)] culminated in a deuterium-tritium (DT) layered implosion driven by a 6.8 ns, 2-shock laser pulse. This paper describes these experiments and comparisons with ICF design code simulations. Backlit radiography of a tritium-hydrogen-deuterium (THD) layered capsule demonstrated an ablator implosion velocity of 385 km/s with a slightly oblate hot spot shape. Other diagnostics suggested an asymmetric compressed fuel layer. A streak camera-based hot spot self-emission diagnostic (SPIDER) showed a double-peaked history of the capsule self-emission. Simulations suggest that this is a signature of low quality hot spot formation. Changes to the laser pulse and pointing for a subsequent DT implosion resulted in a higher temperature, prolate hot spot and a thermonuclear yield of 1.8 × 10{sup 15} neutrons, 40% of the 1D simulated yield.

Oxidation and deuterium uptake of Zr-2.5Nb pressure tubes in CANDU-PHW reactors

International Nuclear Information System (INIS)

Urbanic, V.F.; Warr, B.D.; Manolescu, A.; Chow, C.K.; Shanahan, M.W.

1989-01-01

Oxidation and deuterium uptake in Zr-2.5Nb pressure tubes are being monitored by destructive examination of tubes removed from commercial Canadian deuterium uranium pressurized heavy-water (CANDU-PHW) stations and by analyses of microsamples, obtained in-situ, from the inside surface of tubes in the reactor. Unlike Zircaloy-2, there is no evidence for any acceleration in the oxidation rate for exposures up to about 4500 effective full power days. Changes towards a more equilibrium microstructure during irradiation may be partly responsible for maintaining the low oxidation rate, since thermal aging treatments, producing similar microstructural changes in initially cold worked tubes, were found to improve out-reactor corrosion resistance in 589 K water. With one exception, the deuterium uptake in Zr-2.5Nb tubes has been remarkably low and no greater than 3-mg/kg deuterium per year (0.39 mg/dm 2 hydrogen per year) . The exception is the most recent surveillance tube removed from Pickering (NGS) Unit 3, which had a deuterium content near the outlet end about five times higher than that seen in the previous tube examined. Current investigations suggest that most of the uptake in that tube may have come from the gas annulus surrounding the tube where deuterium exists as an impurity, and oxidation has been insufficient to maintain a protective oxide film. Results from weight gain measurements, chemical analyses, metallography, scanning electron microscopy, and transmission electron microscopy of irradiated pressure tubes and of small coupons exposed out reactor are presented and discussed with respect to the observed corrosion and hydriding behavior of CANDU-PHW pressure tubes. (author)

Deuterium secondary isotope kinetic effects in imine formation reactions

International Nuclear Information System (INIS)

Amaral, L. do; Rossi, M.H.

1986-01-01

The kinetic α-deuterium isotope effects, K D /K H , for reaction mechanisms is studied. The reaction of pH function to m-bromobenzaldehyde, semicarbazide nucleophile, methoxy-amine and hydroxylamine are analysed. (M.J.C.) [pt

The need for accurate deuterium analysis in a heavy water plant and its achievement

International Nuclear Information System (INIS)

Singh, R.R.; Pradhan, D.G.

1979-01-01

Importance of Mass Spectrometer as an analytical tool for deuterium analysis in heavy water plants is discussed. Some of the important requirements such as memory effect and H 3 + correction are described with reference to the Mass Spectrometer used at HWP (Talcher). For achieving the accuracy required, use of international deuterium standards and error estimation found by intercalibration are discussed. (auth.)

Conformational Assessment of Adnectin and Adnectin-Drug Conjugate by Hydrogen/Deuterium Exchange Mass Spectrometry

Science.gov (United States)

Huang, Richard Y.-C.; O'Neil, Steven R.; Lipovšek, Daša; Chen, Guodong

2018-05-01

Higher-order structure (HOS) characterization of therapeutic protein-drug conjugates for comprehensive assessment of conjugation-induced protein conformational changes is an important consideration in the biopharmaceutical industry to ensure proper behavior of protein therapeutics. In this study, conformational dynamics of a small therapeutic protein, adnectin 1, together with its drug conjugate were characterized by hydrogen/deuterium exchange mass spectrometry (HDX-MS) with different spatial resolutions. Top-down HDX allows detailed assessment of the residue-level deuterium content in the payload conjugation region. HDX-MS dataset revealed the ability of peptide-based payload/linker to retain deuterium in HDX experiments. Combined results from intact, top-down, and bottom-up HDX indicated no significant conformational changes of adnectin 1 upon payload conjugation. [Figure not available: see fulltext.

The sensitizing phenomenon of X-ray film in the experiment of metals loaded with deuterium

International Nuclear Information System (INIS)

Chen Suhe; Wang Dalun; Chen Wenjang; Li Yijun; Fu Yibei; Zhang Xinwei

1993-01-01

The sensitizing phenomenon of X-ray film was studied, in metals loaded with deuterium, by a cycle method of temperature and pressure (CMTP). The experimental results showed that the sensitization of X-ray film was derived from the chemical reaction and the anomalous effect of metals loaded with deuterium. (author)

Deuterium oxide normalizes blood pressure and vascular calcium uptake in Dahl salt-sensitive hypertensive rats

International Nuclear Information System (INIS)

Vasdev, S.; Prabhakaran, V.; Sampson, C.A.

1990-01-01

This study examined the effect of 25% deuterium oxide in drinking water on systolic blood pressure, uptakes of calcium, and rubidium 86 by aortas of Dahl salt-sensitive rats on 0.4% (low) and 8% (high) sodium chloride (salt) diet. Twenty-four rats were divided into four groups. Groups I and II were on the low salt diet and groups III and IV on the high salt diet from 6 weeks of age. Additionally, at 10 weeks of age groups I and III were placed on 100% water and groups II and IV on 25% deuterium oxide. At 14 weeks, systolic blood pressure, uptakes of calcium, and rubidium 86 by aortas were significantly higher (p less than 0.01) in rats on the high salt diet as compared with those on the low salt diet. Deuterium oxide intake normalized systolic blood pressure and aortic calcium uptake but not aortic rubidium 86 uptake in hypertensive rats on the high salt diet. Deuterium oxide had no effect on blood pressure or aortic calcium uptake in rats on the low salt diet. The parallel increase in systolic blood pressure and vascular calcium uptake suggests that increased calcium uptake mechanisms are associated with hypertension in salt-sensitive Dahl rats. Furthermore, deuterium oxide appears to normalize elevated blood pressure in salt-sensitive hypertensive rats by normalizing elevated vascular (aortic) calcium uptake

Deuterium labelling studies with unsaturated acids and nitriles

International Nuclear Information System (INIS)

Desai, U.V.; Mane, R.B.

1986-01-01

α-Deuteriated α,β-unsaturated acids have been prepared by Knoevenagel condensation of aldehydes with deuteriated malonic acid. The decarboxylation of α,β-unsaturated cyano acid with pyridine/D 2 O yields α- and γ-labelled nitriles. The deuterium incorporation is studied by pmr spectroscopy. (author). 8 refs

Direct in vivo characterization of delta 5 desaturase activity in humans by deuterium labeling: Effect of insulin

International Nuclear Information System (INIS)

el Boustani, S.; Causse, J.E.; Descomps, B.; Monnier, L.; Mendy, F.; Crastes de Paulet, A.

1989-01-01

The conversion of dihomogamma linolenic acid (DHLA) into arachidonic acid (AA) was compared in normal subjects and diabetic patients before and after treatment with insulin. The kinetics of the incorporation of deuterium-labeled DHLA and its conversion product, deuterium-labeled AA, was determined in plasma triglycerides, plasma phospholipids, and platelet lipids of subjects after ingestion of 2 g of the labeled precursor. Analysis was performed by gas liquid chromatography-mass spectrometry using multiple ion detection. In normal subjects, the deuterium-labeled DHLA concentration rose to 24 to 69 mg/L in plasma triglycerides four to nine hours after ingestion and to 20 to 34 mg/L in plasma phospholipids about four hours later. Deuterium-labeled AA appeared at 12 hours, rose to 2.4 to 3.8 mg/L between 48 and 72 hours in plasma phospholipids, but remained at the limit of detection in plasma triglycerides and was undetectable in platelet lipids. In diabetic patients both before and after insulin treatment, the deuterium-labeled DHLA concentration in plasma triglycerides and in plasma phospholipids followed the same pattern as in normal subjects. However, the deuterium-labeled arachidonic acid concentration was below 1 mg/L in plasma phospholipids before insulin. After insulin treatment the patients recovered normal DHLA metabolism because deuterium-labeled AA rose in phospholipids to a mean value of 3.5 mg/L, which is in the same range as that observed in normal subjects (3.2 mg/L). The present data provide direct evidence for the conversion of DHLA into AA in humans. The effect of insulin and the data from the literature of animal studies suggest insulin dependence of delta 5 desaturase in humans

Magnetohydrodynamic simulation of solid-deuterium-initiated Z-pinch experiments

International Nuclear Information System (INIS)

Sheehey, P.T.

1994-02-01

Solid-deuterium-initiated Z-pinch experiments are numerically simulated using a two-dimensional resistive magnetohydrodynamic model, which includes many important experimental details, such as ''cold-start'' initial conditions, thermal conduction, radiative energy loss, actual discharge current vs. time, and grids of sufficient size and resolution to allow realistic development of the plasma. The alternating-direction-implicit numerical technique used meets the substantial demands presented by such a computational task. Simulations of fiber-initiated experiments show that when the fiber becomes fully ionized rapidly developing m=0 instabilities, which originated in the coronal plasma generated from the ablating fiber, drive intense non-uniform heating and rapid expansion of the plasma column. The possibility that inclusion of additional physical effects would improve stability is explored. Finite-Larmor-radius-ordered Hall and diamagnetic pressure terms in the magnetic field evolution equation, corresponding energy equation terms, and separate ion and electron energy equations are included; these do not change the basic results. Model diagnostics, such as shadowgrams and interferograms, generated from simulation results, are in good agreement with experiment. Two alternative experimental approaches are explored: high-current magnetic implosion of hollow cylindrical deuterium shells, and ''plasma-on-wire'' (POW) implosion of low-density plasma onto a central deuterium fiber. By minimizing instability problems, these techniques may allow attainment of higher temperatures and densities than possible with bare fiber-initiated Z-pinches. Conditions for significant D-D or D-T fusion neutron production may be realizable with these implosion-based approaches

Reprint of: Effects of cold deformation, electron irradiation and extrusion on deuterium desorption behavior in Zr-1%Nb alloy

Science.gov (United States)

Morozov, O.; Mats, O.; Mats, V.; Zhurba, V.; Khaimovich, P.

2018-01-01

The present article introduces the data of analysis of ranges of ion-implanted deuterium desorption from Zr-1% Nb alloy. The samples studied underwent plastic deformation, low temperature extrusion and electron irradiation. Plastic rolling of the samples at temperature ∼300 K resulted in plastic deformation with the degree of ε = 3.9 and the formation of nanostructural state with the average grain size of d = 61 nm. The high degree of defectiveness is shown in thermodesorption spectrum as an additional area of the deuterium desorption in the temperature ranges 650-850 K. The further processing of the sample (that had undergone plastic deformation by plastic rolling) with electron irradiation resulted in the reduction of the average grain size (58 nm) and an increase in borders concentration. As a result the amount of deuterium desorpted increased in the temperature ranges 650-900 K. In case of Zr-1% Nb samples deformed by extrusion the extension of desorption area is observed towards the temperature reduction down to 420 K. The formation of the phase state of deuterium solid solution in zirconium was not observed. The structural state behavior is a control factor in the process of deuterium thermodesorption spectrum structure formation with a fixed implanted deuterium dose (hydrogen diagnostics). It appears as additional temperature ranges of deuterium desorption depending on the type, character and defect content.

Cosmic Ray Deuterium from 0.2 to 3.0 GeV/nucleon

DEFF Research Database (Denmark)

Davis, A.J.; Labrador, A.W.; Mewaldt, R.A.

1996-01-01

The abundances of cosmic ray protons and deuterium between 0.2 and 3.0 GeV/nucleon were measured by the IMAX balloon--borne magnet spectrometer during a flight in July, 1992. These isotope measurements extend to significantly higher energies than have previously been achieved. A high--resolution ......The abundances of cosmic ray protons and deuterium between 0.2 and 3.0 GeV/nucleon were measured by the IMAX balloon--borne magnet spectrometer during a flight in July, 1992. These isotope measurements extend to significantly higher energies than have previously been achieved. A high...

Technological aspects of cryogenic laser-fusion targets

International Nuclear Information System (INIS)

Musinski, D.L.; Henderson, T.M.; Simms, R.J.; Pattinson, T.R.; Jacobs, R.B.

1980-01-01

Most current laser-fusion targets consist of hollow spherical glass shells which have been filled with a mixture of gaseous deuterium-tritium fuel. Theoretical considerations suggest that optimum yields can be obtained from these targets if the fuel is condensed as a uniform liquid or solid layer on the inner surface of the glass shell at the time it is irradiated. In principle, this can be accomplished in a straightforward way by cooling the target below the condensation or freezing point of the fuel. In practice, cryogenic targets can appear in routine laser experiments only when the necessary cryogenic technology is reliably integrated into experimental target chambers. Significant progress has been made recently in this field. The authors will discuss the scientific basis and the various technological features of a system which has allowed the successful irradiation of uniform solid-fuel-layer targets

AN ANALYSIS OF THE DEUTERIUM FRACTIONATION OF STAR-FORMING CORES IN THE PERSEUS MOLECULAR CLOUD

Energy Technology Data Exchange (ETDEWEB)

Friesen, R. K. [National Radio Astronomy Observatory, 520 Edgemont Rd., Charlottesville, VA 22903 (United States); Kirk, H. M. [Origins Institute, McMaster University, 1280 Main Street West, Hamilton, ON L8S 4M1 (Canada); Shirley, Y. L., E-mail: friesen@di.utoronto.ca [Steward Observatory, University of Arizona, 933 N. Cherry Ave., Tucson, AZ 85721 (United States)

2013-03-01

We have performed a pointed survey of N{sub 2}D{sup +} 2-1 and N{sub 2}D{sup +} 3-2 emission toward 64 N{sub 2}H{sup +}-bright starless and protostellar cores in the Perseus molecular cloud using the Arizona Radio Observatory Submillimeter Telescope and Kitt Peak 12 m telescope. We find a mean deuterium fractionation in N{sub 2}H{sup +}, R{sub D} = N(N{sub 2}D{sup +})/N(N{sub 2}H{sup +}), of 0.08, with a maximum R{sub D} = 0.2. In detected sources, we find no significant difference in the deuterium fractionation between starless and protostellar cores, nor between cores in clustered or isolated environments. We compare the deuterium fraction in N{sub 2}H{sup +} with parameters linked to advanced core evolution. We only find significant correlations between the deuterium fraction and increased H{sub 2} column density, as well as with increased central core density, for all cores. Toward protostellar sources, we additionally find a significant anticorrelation between R{sub D} and bolometric temperature. We show that the Perseus cores are characterized by low CO depletion values relative to previous studies of star-forming cores, similar to recent results in the Ophiuchus molecular cloud. We suggest that the low average CO depletion is the dominant mechanism that constrains the average deuterium fractionation in the Perseus cores to small values. While current equilibrium and dynamic chemical models are able to reproduce the range of deuterium fractionation values we find in Perseus, reproducing the scatter across the cores requires variation in parameters such as the ionization fraction or the ortho-to-para-H{sub 2} ratio across the cloud, or a range in core evolution timescales.

Permeation behavior of deuterium implanted into beryllium

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Hirofumi; Hayashi, Takumi; O' hira, Shigeru; Nishi, Masataka [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-09-01

Study on Implantation Driven Permeation (IDP) behavior of deuterium through pure beryllium was investigated as a part of the research to predict the tritium permeation through the first wall components ITER (International Thermonuclear Experimental Reactor). The permeation experiments were carried out with two beryllium specimens, one was an unannealed specimen and the other was that annealed at 1173 K. The permeation flux was measured as a function of specimen temperature and incident ion flux. Surface analysis of specimen was also carried out after the permeation experiment. Permeation was observed only with the annealed specimen and no significant permeation was observed with unannealed specimen under the present experimental condition (maximum temperature: 685 K, detection limit: 1x10{sup 13} D atoms/m{sup 2}s). It could be attributed that the intrinsic lattice defects, which act as diffusion preventing site, decreased with the specimen annealing. Based on the result of steady and transient permeation behavior and surface analysis, it was estimated that the deuterium permeation implanted into annealed beryllium was controlled by surface recombination due to the oxide layer on the surface of the permeated side. (author)

Method for the preparation of deuterium-enriched water in the preparation of hydrogen

International Nuclear Information System (INIS)

Mandrin, C.

1984-01-01

The synthesis-gas plant is operated in a number of successive operating periods such that during the first operating period an excess of fresh water is supplied to the synthesis gas plant and the waste water from the resulting mixture is separated in a condenser and supplied to a storage container. During the subsequent operating periods, the waste water stored in the container is used as the feed water for the synthesis gas plant and the waste water obtained on each occasion is stored in the container with increasing deuterium concentration. The waste water obtained during the last operating period and having the highest deuterium concentration is used to feed a plant for producing heavy water. This process, when used in a synthesis gas plant for producing hydrogen, can be used to obtain deuterium-enriched water as a feedstock for a heavy-water plant without expensive additional energy-consuming devices

Annihilation of antiprotons stopped in liquid hydrogen and deuterium

International Nuclear Information System (INIS)

Dalkarov, O.D.; Kerbikov, B.O.; Markushin, V.E.

1976-01-01

Detailed analysis is given of stopping antiproton annihilation in liquid hydrogen and deuterium. Connection between capture schedule and properties of bound states in nucleon-antinucleon system is established. The theoretical predictions are compared with experimental data which appeared in 1971-75

Optimisation of the manufacturing process of tritide and deuteride targets used for neutron production

International Nuclear Information System (INIS)

Monnin, Carole; Bach, Pierre; Tulle, Pierre Alain; Rompay, Marc van; Ballanger, Anne

2002-01-01

As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium targets on copper substrates, and going to more sophisticated devices. The range of possible uses is wide, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets or large size rotating targets for higher lifetimes. The activity of the targets ranges from 3.7x10 10 to 3.7x10 13 Bq (1-1000 Ci), the diameter being up to 30 cm. Sodern and the CEA/Valduc centre have developed different technologies for tritium target manufacture, allowing the selection of the best configuration for each kind of use. In order to optimize the production of high energy neutrons, the performance of tritide and deuteride titanium targets made by different processes has been studied experimentally by bombardment with 120 and 350 kV deuterons provided by electrostatic accelerators. It is then possible to optimize either neutron output or lifetime and stability or thermal behaviour. The importance of the deposit evaporation conditions on the efficiency of neutron emission is clearly demonstrated, as well as the thermomechanical stability of the Ti thin film under deuteron bombardment. The main parameters involved in the target performance are discussed from a thermodynamical approach

Optimisation of the manufacturing process of tritide and deuteride targets used for neutron production

Science.gov (United States)

Monnin, Carole; Bach, Pierre; Tulle, Pierre Alain; van Rompay, Marc; Ballanger, Anne

2002-03-01

As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium targets on copper substrates, and going to more sophisticated devices. The range of possible uses is wide, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets or large size rotating targets for higher lifetimes. The activity of the targets ranges from 3.7×10 10 to 3.7×10 13 Bq (1-1000 Ci), the diameter being up to 30 cm. Sodern and the CEA/Valduc centre have developed different technologies for tritium target manufacture, allowing the selection of the best configuration for each kind of use. In order to optimize the production of high energy neutrons, the performance of tritide and deuteride titanium targets made by different processes has been studied experimentally by bombardment with 120 and 350 kV deuterons provided by electrostatic accelerators. It is then possible to optimize either neutron output or lifetime and stability or thermal behaviour. The importance of the deposit evaporation conditions on the efficiency of neutron emission is clearly demonstrated, as well as the thermomechanical stability of the Ti thin film under deuteron bombardment. The main parameters involved in the target performance are discussed from a thermodynamical approach.

Deuterium measurement by emission spectrometry

International Nuclear Information System (INIS)

Niemann, E.G.; Heilig, K.; Dumke, I.

1978-01-01

The method makes it possible to determine the relative deuterium content of enriched water samples. For this, the relative intensities of the Hα and Dα lines are measured which are emitted by a high-frequency discharge in water vapour. Although the method is not as exact as mass spectrometry, it has the following advantages: - Easy sample preparation (no reduction necessary); - samples of highly different enrichment can be measured one after the other without the danger of memory effects; - much lower apparatus and cost expenditure. The necessary sample size is about the same in both methods. (orig.) [de

Deuterium Liner and Multiparameter Investigation of the Inverse Z-Pinch Formation Process

CERN Document Server

Bystritskii, Vyach M; Grebenyuk, V M; Parzhitsky, S S; Penkov, F M; Stolupin, V A; Boznyak, J; Gula, E; Dudkin, G N; Nechaev, B A; Padalko, V M; Mesyats, G A; Ratakhin, N A; Sorokin, S A

2001-01-01

A description of the methods and results of the measurements of the ion energy distribution of the deuterium liner accelerated in the inverse Z-pinch configuration are presented - the liner plasma is radially accelerated from the outward small radius. The knowledge of the experiment deuteron energy distribution is crucially important for correct interpretation of the results on the study of the dd-reaction at infralow collision energies using the liner plasma. Experiments were fulfilled in the HCEI (Tomsk, Russia) at a nanosecond pulsed high current generator (I=950 kA, pulse duration \\tau=80 ns). The hollow deuterium liner of 20 mm length was accelerated from the initial radius of \\sim 15 mm to 45 mm. Measurement of the liner characteristics was produced by means of the light detectors (detection of H_\\alpha and H_\\beta deuterium lines) and magnetic B-dot probes, placed on the various radii of the expanding liner. Besides, the measurement of the neutron radiation intensity due to reaction d+d\\to^{3}He+n was ...

Deeply virtual Compton scattering off unpolarised deuterium at HERMES

Energy Technology Data Exchange (ETDEWEB)

Hill, Gordon D.

2008-10-15

The HERMES experiment was a forward angle spectrometer on the HERA storage ring at DESY, Hamburg, Germany. HERMES successfully increased understanding of the ''spin puzzle'', the spin structure of the nucleon, by providing high precision measurements of {delta}{sigma} in the Quark Parton Model, the fraction of the spin carried by the current quarks. Following the link of another piece of the puzzle, the orbital angular momentum of quarks and gluons, to the Generalised Parton Distribution (GPD) theoretical framework, HERMES focused on measurements of the Deeply Virtual Compton Scattering (DVCS) process. These measurements are sensitive to GPDs, allowing further experimental constraints to be made on the components of nucleon spin. In the Winter shutdown period 2005-2006 HERMES was upgraded with a Recoil Detector in the target region. This allowed the experiment to make exclusive measurements of the DVCS process for the rst time, reducing background and increasing the resolution of various kinematic variables. The method for reconstructing particle tracks in the inhomogeneous magnetic eld is investigated here. DVCS o a deuterium target is measured with all available data prior to the installation of the Recoil Detector. A comparison is made to currently available models of spin-(1)/(2) GPDs. This analysis has been approved for publication by the HERMES collaboration. The data is further employed in an investigation of a model dependent constraint of the total angular momentum of up and down quarks in the nucleon. (orig.)

Deeply virtual Compton scattering off unpolarised deuterium at HERMES

International Nuclear Information System (INIS)

Hill, Gordon D.

2008-08-01

The HERMES experiment was a forward angle spectrometer on the HERA storage ring at DESY, Hamburg, Germany. HERMES successfully increased understanding of the ''spin puzzle'', the spin structure of the nucleon, by providing high precision measurements of ΔΣ in the Quark Parton Model, the fraction of the spin carried by the current quarks. Following the link of another piece of the puzzle, the orbital angular momentum of quarks and gluons, to the Generalised Parton Distribution (GPD) theoretical framework, HERMES focused on measurements of the Deeply Virtual Compton Scattering (DVCS) process. These measurements are sensitive to GPDs, allowing further experimental constraints to be made on the components of nucleon spin. In the Winter shutdown period 2005-2006 HERMES was upgraded with a Recoil Detector in the target region. This allowed the experiment to make exclusive measurements of the DVCS process for the rst time, reducing background and increasing the resolution of various kinematic variables. The method for reconstructing particle tracks in the inhomogeneous magnetic eld is investigated here. DVCS o a deuterium target is measured with all available data prior to the installation of the Recoil Detector. A comparison is made to currently available models of spin-(1)/(2) GPDs. This analysis has been approved for publication by the HERMES collaboration. The data is further employed in an investigation of a model dependent constraint of the total angular momentum of up and down quarks in the nucleon. (orig.)

Deeply virtual Compton scattering off unpolarised deuterium at HERMES

Energy Technology Data Exchange (ETDEWEB)

Hill, Gordon D

2008-10-15

The HERMES experiment was a forward angle spectrometer on the HERA storage ring at DESY, Hamburg, Germany. HERMES successfully increased understanding of the ''spin puzzle'', the spin structure of the nucleon, by providing high precision measurements of {delta}{sigma} in the Quark Parton Model, the fraction of the spin carried by the current quarks. Following the link of another piece of the puzzle, the orbital angular momentum of quarks and gluons, to the Generalised Parton Distribution (GPD) theoretical framework, HERMES focused on measurements of the Deeply Virtual Compton Scattering (DVCS) process. These measurements are sensitive to GPDs, allowing further experimental constraints to be made on the components of nucleon spin. In the Winter shutdown period 2005-2006 HERMES was upgraded with a Recoil Detector in the target region. This allowed the experiment to make exclusive measurements of the DVCS process for the rst time, reducing background and increasing the resolution of various kinematic variables. The method for reconstructing particle tracks in the inhomogeneous magnetic eld is investigated here. DVCS o a deuterium target is measured with all available data prior to the installation of the Recoil Detector. A comparison is made to currently available models of spin-(1)/(2) GPDs. This analysis has been approved for publication by the HERMES collaboration. The data is further employed in an investigation of a model dependent constraint of the total angular momentum of up and down quarks in the nucleon. (orig.)

Regional and temporal variations of deuterium in the precipitation and atmospheric moisture of Central Europe

International Nuclear Information System (INIS)

Huebner, H.; Kowski, P.; Hermichen, W.D.; Richter, W.; Schuetze, H.

1979-01-01

Regional and temporal variations of deuterium in precipitation and in atmospheric moisture provide the opportunity to balance water cycles as additional but independent information. Variations of deuterium have been measured in precipitation samples from six stations in different zones of the German Democratic Republic since 1972. The aim of the subsequent mathematical processing was to find a functional connection between the deuterium variations and the meteorological parameters causing them. The isotopic content of atmospheric moisture in different air masses and the isotopic content of precipitation are determined by the evaporation conditions of the area of origin and by the number and intensity of evaporation and condensation (precipitation) processes en route from this area of origin to the observation point. Obviously the temperatures at which evaporation and condensation processes take place are of crucial importance. The deuterium values are correlated with the monthly mean temperature. It has been observed, for example, that the equations of regression between precipitation and atmospheric moisture (valid in the case of Leipzig station) differ only with regard to their absolute terms. This follows from the fact that the deuterium is generally enriched by up to 80 per mille in precipitation. Following the well-known fact that many meteorological phenomena show frequencies, an attempt was made to apply the Fourier analysis for the deltaD variations. Relevant harmonic parts were found in all the deltaD series studied, which are repetitious and independent of the station and the observation period. (author)

The Continuous Wave Deuterium Demonstrator (CWDD) design and status

Energy Technology Data Exchange (ETDEWEB)

Todd, A.M.M. (Grumman Space and Electronics Corp., Princeton, NJ (United States)); Nightingale, M.P.S. (AEA Industrial Technology, Culham (United Kingdom)); Yule, T.J. (Argonne National Lab., IL (United States))

1992-01-01

The design of the Continuous Wave Deuterium Demonstrator (CWDD) and the status of the fabricated hardware is presented. The CWDD is a high brightness, 352 MHz, CW linear accelerator designed to deliver a 7.54 MeV, 80 mA D[sup [minus

Influence of traps on the deuterium behaviour in the low activation martensitic steels F82H and Batman

International Nuclear Information System (INIS)

Serra, E.

1997-01-01

A time dependent permeation method is used to measure the permeability, diffusivity and solubility of deuterium in the low activation martensitic steels F82H and Batman. The measurements cover the temperature range from 373 to 743 K which includes the onset of deuterium trapping effects on diffusivity and solubility. The results are interpreted using a trapping model. The number of trap sites and their average energies for deuterium in F82H and Batman steels are determined. (orig.)

Influence of traps on the deuterium behaviour in the low activation martensitic steels F82H and Batman

Science.gov (United States)

Serra, E.; Perujo, A.; Benamati, G.

1997-06-01

A time dependent permeation method is used to measure the permeability, diffusivity and solubility of deuterium in the low activation martensitic steels F82H and Batman. The measurements cover the temperature range from 373 to 743 K which includes the onset of deuterium trapping effects on diffusivity and solubility. The results are interpreted using a trapping model. The number of trap sites and their average energies for deuterium in F82H and Batman steels are determined.

Polarized gas targets for storage rings

International Nuclear Information System (INIS)

Holt, R.J.

1990-01-01

It is widely recognized that polarized gas targets in electron storage rings represent a new opportunity for precision nuclear physics studies. New developments in polarized target technology specific to internal applications will be discussed. In particular, polarized gas targets have been used in the VEPP-3 electron ring in Novosibirsk. A simple storage cell was used to increase the total target thickness by a factor of 15 over the simple gas jet target from an atomic beam source. Results from the initial phase of this project will be reported. In addition, the plans for increasing the luminosity by an additional order or magnitude will be presented. The application of this work to polarized hydrogen and deuterium targets for the HERA ring will be noted. The influence of beam-induced depolarization, a phenomena encountered in short-pulse electron storage rings, will be discussed. Finally, the performance tests of laser-driven sources will be presented. 8 refs., 12 figs., 1 tab

Ion irradiated graphite exposed to fusion-relevant deuterium plasma

International Nuclear Information System (INIS)

Deslandes, Alec; Guenette, Mathew C.; Corr, Cormac S.; Karatchevtseva, Inna; Thomsen, Lars; Ionescu, Mihail; Lumpkin, Gregory R.; Riley, Daniel P.

2014-01-01

Graphite samples were irradiated with 5 MeV carbon ions to simulate the damage caused by collision cascades from neutron irradiation in a fusion environment. The ion irradiated graphite samples were then exposed to a deuterium plasma in the linear plasma device, MAGPIE, for a total ion fluence of ∼1 × 10 24 ions m −2 . Raman and near edge X-ray absorption fine structure (NEXAFS) spectroscopy were used to characterize modifications to the graphitic structure. Ion irradiation was observed to decrease the graphitic content and induce disorder in the graphite. Subsequent plasma exposure decreased the graphitic content further. Structural and surface chemistry changes were observed to be greatest for the sample irradiated with the greatest fluence of MeV ions. D retention was measured using elastic recoil detection analysis and showed that ion irradiation increased the amount of retained deuterium in graphite by a factor of four

Cross sections and equilibrium fractions of deuterium ions and atoms in metal vapors. Progress report, June 1, 1978-May 31, 1979

International Nuclear Information System (INIS)

Morgan, T.J.

1979-01-01

The purpose of this program is to measure cross sections and equilibrium fractions of deuterium ions and atoms in metal vapors. In particular, in connection with double charge exchange D - ion sources, there is concern with D - formation in alkaline-earth vapor targets. Also, in connection with possible metal vapor contamination in the system, there is concern with cross sections for high energy D + , D 0 and D - collisions with these metal vapors. Results from this research will fill in a gap in knowledge of single and double charge transfer and multiple collision processes in alkaline-earth targets and provide a better understanding of D - formation mechanisms. A list of publications is included. 6 references

The pion-nucleon scattering lengths from pionic hydrogen and deuterium

Energy Technology Data Exchange (ETDEWEB)

Schroeder, H.-C.; Badertscher, A.; Goudsmit, P.F.A.; Janousch, M.; Leisi, H.J.; Matsinos, E.; Sigg, D.; Zhao, Z.G. [ETH Zurich, Inst. for Particle Physics, Zurich (Switzerland); Chatellard, D.; Egger, J.P. [Neuchatel Univ. (Switzerland). Inst. de Physique; Gabathuler, K.; Hauser, P.; Simons, L.M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Rusi El Hassani, A.J. [Dept. de Physique, Faculte des Sciences et Technique, Tanger (Morocco)

2001-07-01

This is the final publication of the ETH Zurich-Neuchatel-PSI collaboration on the pionic hydrogen and deuterium precision X-ray experiments. We describe the recent hydrogen 3p-1s measurement, report on the determination of the Doppler effect correction to the transition line width, analyze the deuterium shift measurement and discuss implications of the combined hydrogen and deuterium results. From the pionic hydrogen 3p-1s transition experiments we obtain the strong-interaction energy level shift {epsilon}{sub 1s} = -7.108{+-}0.013 (stat.){+-}0.034 (syst.) eV and the total decay width {gamma}{sub 1s} = 0.868{+-}0.040 (stat.){+-}0.038 (syst.) eV of the 1s state. Taking into account the electromagnetic corrections we find the hadronic {pi}N s-wave scattering amplitude a{sub {pi}{sup -}p{yields}{pi}{sup -}p} = 0.0883{+-}0.0008 m{sub {pi}}{sup -1} for elastic scattering and a{sub {pi}{sup -}p{yields}{pi}{sup 0}n} = -0.128{+-}0.006 m{sub {pi}} {sup -1} for single charge exchange, respectively. We then combine the pionic hydrogen results with the 1s level shift measurement on pionic deuterium and test isospin symmetry of the strong interaction: our data are still compatible with isospin symmetry. The isoscalar and isovector {pi}N scattering lengths (within the framework of isospin symmetry) are found to be b{sub 0} = -0.0001{sup +0.0009}{sub -0.0021} m{sub {pi}}{sup -1} and b{sub 1} = -0.0885{sup +0.0010}{sub -0.0021} m{sub {pi}} {sup -1}, respectively. Using the GMO sum rule, we obtain from b{sub 1} a new value of the {pi}N coupling constant (g{sub {pi}}{sub N} = 13.21{sub -0.05}{sup +0.11}) from which follows the Goldberger-Treiman discrepancy {delta}{sub GT}=0.027{sub -0.008}{sup +0.012}. The new values of b{sub 0} and g{sub {pi}}{sub N} imply an increase of the nucleon sigma term by at least 9 MeV. (orig.)

Absolute measurement of the isotopic ratio of a water sample with very low deuterium content

International Nuclear Information System (INIS)

Hagemann, R.; Nief, G.; Roth, E.

1968-01-01

The presence of H 3+ ions which are indistinguishable from HD + ions presents the principal difficulty encountered in the measurement of isotopic ratios of water samples with very low deuterium contents using a mass spectrometer. Thus, when the sample contains no deuterium, the mass spectrometer does not indicate zero. By producing, in situ, from the sample to be measured, water vapor with an isotopic ratio very close to zero using a small distilling column, this difficulty is overcome. This column, its operating parameters, as well as the way in which the measurements are made are described. An arrangement is employed in which the isotopic ratios can be measured with a sensitivity better than 0.01 x 10 -6 . The method is applied to the determination of the isotopic ratios of three low deuterium content water samples. The results obtained permit one to assign to the sample with the lowest deuterium content an absolute value equal to 1.71 ± 0.03 ppm. This water sample is a primary standard from which is determined the isotopic ratio of a natural water sample which serves as the laboratory standard. (author) [fr

Kinetic formulae for muon-catalyzed fusion of hydrogen isotopes and their application to the description of the data for pure deuterium

International Nuclear Information System (INIS)

Gula, A.

1987-01-01

The data on the time distributions of muon-catalyzed fusion (μCF) events in pure deuterium targets published before 1987 are analysed using the kinetic formalism developed by the author and collaborators in a series of papers. The formalism enables one to describe these time distributions in an arbitrary mixture of hydrogen isotopes with strict inclusion of registration efficiency and dead time. The kinetic formulae for such distributions can be readily obtained using a prescription based on the theory of signal-flow graphs even for very complicated kinetic situations, thus, allowing one to avoid the simplifying assumptions which have been usually made in earlier analyses. Practically all important processes forming the muon-catalysis chain can be strictly taken into account in the approximation of constant transition rates. Consecutive μCF cycles can be described separately, which provides a useful tool in data analysis. The developed formalism is applied to the existing data for pure deuterium. First cycle-by-cycle time distributions reported for room temperature by the Gatchina group are analysed. 93 refs., 14 figs. (author)

Analysis of hydrogen-deuterium mixtures and of mixtures of heavy-water and light-water by means of a mass spectrometer; Analyse des melanges hydrogene-deuterium et des melanges d'eau lourde et d'eau legere au moyen du spectrometre de masse

Energy Technology Data Exchange (ETDEWEB)

Chenouard, J; Gueron, J; Roth, E

1951-07-01

The differences between hydrogen and deuterium with respect to the capture of thermal neutrons (hydrogen = 0.31 barn; deuterium 0.00065 barn) explains the interest of detecting small variations of the isotopic composition of the heavy waters used in the Chatillon nuclear pile. The aim of this report is to describe and discuss the method used since more than a year for the dosimetry of heavy waters. After a recall of the principle of mass spectroscopy analysis of deuterium-hydrogen mixtures, the preciseness of the results is presented and the balancing method used for the determination of the isotopic composition of hydrogen-deuterium mixtures is explained in detail. Finally, a brief comparison of the preciseness of mass spectroscopy measurements with the analyses made with other methods is performed. Some calculations and the tables of results are presented in appendixes. (J.S.)

A Dosimetry Study of Deuterium-Deuterium Neutron Generator-based In Vivo Neutron Activation Analysis.

Science.gov (United States)

Sowers, Daniel; Liu, Yingzi; Mostafaei, Farshad; Blake, Scott; Nie, Linda H

2015-12-01

A neutron irradiation cavity for in vivo neutron activation analysis (IVNAA) to detect manganese, aluminum, and other potentially toxic elements in human hand bone has been designed and its dosimetric specifications measured. The neutron source is a customized deuterium-deuterium neutron generator that produces neutrons at 2.45 MeV by the fusion reaction 2H(d, n)3He at a calculated flux of 7 × 10(8) ± 30% s(-1). A moderator/reflector/shielding [5 cm high density polyethylene (HDPE), 5.3 cm graphite and 5.7 cm borated (HDPE)] assembly has been designed and built to maximize the thermal neutron flux inside the hand irradiation cavity and to reduce the extremity dose and effective dose to the human subject. Lead sheets are used to attenuate bremsstrahlung x rays and activation gammas. A Monte Carlo simulation (MCNP6) was used to model the system and calculate extremity dose. The extremity dose was measured with neutron and photon sensitive film badges and Fuji electronic pocket dosimeters (EPD). The neutron ambient dose outside the shielding was measured by Fuji NSN3, and the photon dose was measured by a Bicron MicroREM scintillator. Neutron extremity dose was calculated to be 32.3 mSv using MCNP6 simulations given a 10-min IVNAA measurement of manganese. Measurements by EPD and film badge indicate hand dose to be 31.7 ± 0.8 mSv for neutrons and 4.2 ± 0.2 mSv for photons for 10 min; whole body effective dose was calculated conservatively to be 0.052 mSv. Experimental values closely match values obtained from MCNP6 simulations. These are acceptable doses to apply the technology for a manganese toxicity study in a human population.

Implantation driven permeation behavior of deuterium through pure tungsten

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Hirofumi E-mail: nakamura@tpl.tokai.jaeri.go.jp; Hayashi, Takumi; Nishi, Masataka; Arita, Makoto; Okuno, Kenji

2001-09-01

Implantation driven permeation behavior of deuterium through pure tungsten has been investigated to estimate the amount of tritium permeation through its barrier in a thermo-nuclear fusion device. The permeation experiments were performed on pure tungsten foil of 25 {mu}m thickness under conditions of incident flux of 1.9x10{sup 18}-1.1x10{sup 19} D{sup +}/m{sup 2}s, incident ion energy of 200-2000 eV, and specimen temperature of 512-660 K. As a result of this steady-state permeation experiment, the rate-determining process of deuterium permeation was found to be controlled by diffusion at both implanted and permeated sides. On the other hand, transient permeation was strongly affected by trap effect in the specimen. Simulation analysis using TMAP code on transient permeation behavior indicates the existence of a trap site with a trap energy of nearly 1eV and with a trap density of over several ten's ppm in tungsten.

Implantation driven permeation behavior of deuterium through pure tungsten

International Nuclear Information System (INIS)

Nakamura, Hirofumi; Hayashi, Takumi; Nishi, Masataka; Arita, Makoto; Okuno, Kenji

2001-01-01

Implantation driven permeation behavior of deuterium through pure tungsten has been investigated to estimate the amount of tritium permeation through its barrier in a thermo-nuclear fusion device. The permeation experiments were performed on pure tungsten foil of 25 μm thickness under conditions of incident flux of 1.9x10 18 -1.1x10 19 D + /m 2 s, incident ion energy of 200-2000 eV, and specimen temperature of 512-660 K. As a result of this steady-state permeation experiment, the rate-determining process of deuterium permeation was found to be controlled by diffusion at both implanted and permeated sides. On the other hand, transient permeation was strongly affected by trap effect in the specimen. Simulation analysis using TMAP code on transient permeation behavior indicates the existence of a trap site with a trap energy of nearly 1eV and with a trap density of over several ten's ppm in tungsten

Hydrogen, deuterium, and tritium isotope exchange experiments in JET

Energy Technology Data Exchange (ETDEWEB)

Horton, L.D.; Andrew, P.; Bracco, G.; Conroy, S.; Corti, S.; Ehrenberg, J.; Goodall, D.H.J.; Jarvis, O.N.; Lomas, P.; Loughlin, M.; Peacock, A.T.; Saibene, G.; Sadler, G.; Sartori, R.; Stamp, M.F.; Thomas, P.R.; Belle, P. van (JET Joint Untertaking, Abingdon, Oxfordshire (United Kingdom))

1992-12-01

Isotope exchange experiments have been performed in JET using hydrogen, deuterium, and, in the recent preliminary tritium experiment (PTE), tritium. The rate of change-over from one isotope to another involves two quite different time constants. We have modelled this behaviour using a multireservoir model which splits the accessible hydrogenic particles into two groups, each having a different rate of exchange of particles with the plasma. By applying this model to the sequence of discharges during and after the PTE, we can determine the parameters in the model. The resulting fit also gives a good representation of hydrogen/deuterium change-over experiments, indicating that the tritium behaves in the same manner as other hydrogen isotopes, at least as far as recycling is concerned. Discrepancies between the model and the actual measurements of tritium recovery after the PTE lead us to conclude that isotope exchange processes resulting from collisions of molecules with the vessel walls play a significant role in spreading tritrium around the machine. (orig.).

Thermal desorption of deuterium implanted into beryllium

International Nuclear Information System (INIS)

Markin, A.V.; Chernikov, V.N.; Zakharov, A.P.

1995-01-01

By means of TDS measurements it is shown that the desorption of deuterium from Be implanted with 5 keV D ions to fluences, Φ, from 1x10 20 D/m 2 to 1x10 21 D/m 2 proceeds in one high temperature stage B, while at Φ ≥ 1.2x10 21 D/m 2 one more stage A is added. The desorption maximum A is narrow and consists of two peaks A 1 and A 2 at about 460 K and 490 K, respectively. Peak A 1 is attributed to the desorption of deuterium from the walls of opened channels formed under D ion implantation. Peak A 2 is a consequence of the opening of a part of closed bubbles/channels to the outer surface. The position of maximum B shifts noticeably and nonsteadily on the fluence in a range from 850 to 1050 K. The origin of this maximum is the liberation of D atoms bound at vacancy complexes discussed previously by Wampler. The dependence of Tm(B) on the fluence is governed by the interaction of freely migrating D atoms with partly opened or fully closed gas cavity arrangements which are created under temperature ramping, but differently in specimens implanted with D ions to different fluences

Spin-polarized hydrogen, deuterium, and tritium : I

International Nuclear Information System (INIS)

Haugen, M.; Ostgaard, E.

1989-01-01

The ground-state energy of spin-polarized hydrogen, deuterium and tritium is calculated by means of a modified variational lowest order constrained-variation method, and the calculations are done for five different two-body potentials. Spin-polarized H is not self-bound according to our theoretical results for the ground-state binding energy. For spin-polarized D, however, we obtain theoretical results for the ground-state binding energy per particle from -0.4 K at an equilibrium particle density of 0.25 σ -3 or a molar volume of 121 cm 3 /mol to +0.32 K at an equilibrium particle density of 0.21 σ -3 or a molar volume of 142 cm 3 /mol, where σ = 3.69 A (1A = 10 -10 m). It is, therefore, not clear whether spin-polarized deuterium should be self-bound or not. For spin-polarized T, we obtain theoretical results for the ground-state binding energy per particle from -4.73 K at an equilibrium particle density of 0.41 σ -3 or a molar volume of 74 cm 3 /mol to -1.21 K at an equilibrium particle density of 0.28 σ -3 or a molar volume of 109 cm 3 /mol. (Author) 27 refs., 9 figs., tab

Defect annealing and thermal desorption of deuterium in low dose HFIR neutron-irradiated tungsten

International Nuclear Information System (INIS)

Shimada, Masashi; Hara, Masanori; Otsuka, Teppei; Oya, Yasuhisa; Hatano, Yuji

2015-01-01

Three tungsten samples irradiated at High Flux Isotope Reactor at Oak Ridge National Laboratory were exposed to deuterium plasma (ion fluence of 1 × 10 26 m −2 ) at three different temperatures (100, 200, and 500 °C) in Tritium Plasma Experiment at Idaho National Laboratory. Subsequently, thermal desorption spectroscopy was performed with a ramp rate of 10 °C min −1 up to 900 °C, and the samples were annealed at 900 °C for 0.5 h. These procedures were repeated three times to uncover defect-annealing effects on deuterium retention. The results show that deuterium retention decreases approximately 70% for at 500 °C after each annealing, and radiation damages were not annealed out completely even after the 3rd annealing. TMAP modeling revealed the trap concentration decreases approximately 80% after each annealing at 900 °C for 0.5 h

Defect annealing and thermal desorption of deuterium in low dose HFIR neutron-irradiated tungsten

Science.gov (United States)

Shimada, Masashi; Hara, Masanori; Otsuka, Teppei; Oya, Yasuhisa; Hatano, Yuji

2015-08-01

Three tungsten samples irradiated at High Flux Isotope Reactor at Oak Ridge National Laboratory were exposed to deuterium plasma (ion fluence of 1 × 1026 m-2) at three different temperatures (100, 200, and 500 °C) in Tritium Plasma Experiment at Idaho National Laboratory. Subsequently, thermal desorption spectroscopy was performed with a ramp rate of 10 °C min-1 up to 900 °C, and the samples were annealed at 900 °C for 0.5 h. These procedures were repeated three times to uncover defect-annealing effects on deuterium retention. The results show that deuterium retention decreases approximately 70% for at 500 °C after each annealing, and radiation damages were not annealed out completely even after the 3rd annealing. TMAP modeling revealed the trap concentration decreases approximately 80% after each annealing at 900 °C for 0.5 h.

Defect annealing and thermal desorption of deuterium in low dose HFIR neutron-irradiated tungsten

Energy Technology Data Exchange (ETDEWEB)

Shimada, Masashi, E-mail: Masashi.Shimada@inl.gov [Fusion Safety Program, Idaho National Laboratory, Idaho Falls, ID (United States); Hara, Masanori [Hydrogen Isotope Research Center, University of Toyama, Toyama (Japan); Otsuka, Teppei [Kyushu University, Interdisciplinary Graduate School of Engineering Science, Higashi-ku, Fukuoka (Japan); Oya, Yasuhisa [Radioscience Research Laboratory, Faculty of Science, Shizuoka University, Shizuoka (Japan); Hatano, Yuji [Hydrogen Isotope Research Center, University of Toyama, Toyama (Japan)

2015-08-15

Three tungsten samples irradiated at High Flux Isotope Reactor at Oak Ridge National Laboratory were exposed to deuterium plasma (ion fluence of 1 × 10{sup 26} m{sup −2}) at three different temperatures (100, 200, and 500 °C) in Tritium Plasma Experiment at Idaho National Laboratory. Subsequently, thermal desorption spectroscopy was performed with a ramp rate of 10 °C min{sup −1} up to 900 °C, and the samples were annealed at 900 °C for 0.5 h. These procedures were repeated three times to uncover defect-annealing effects on deuterium retention. The results show that deuterium retention decreases approximately 70% for at 500 °C after each annealing, and radiation damages were not annealed out completely even after the 3rd annealing. TMAP modeling revealed the trap concentration decreases approximately 80% after each annealing at 900 °C for 0.5 h.

Deuterium concentration deterioration in feed synthesis gas from ammonia plant to heavy water plant (Preprint No. ED-5)

International Nuclear Information System (INIS)

Sah, A.K.

1989-04-01

Heavy Water Plant (Thal) is designed for 110 T/ Year capacity (55 T/Year each stream), with inlet deuterium concentration of feed synthesis gas at 115 ppm and depleted to 15 ppm. During first start up of plant the inlet concentration to feed synthesis gas was about 97 ppm. At that time the rich condensate recirculation was not there. To make the effective recirculation of deuterium rich condensate and minimum posssible losses some modifications were carried out in ammonia plant. Major ones are: (i)Demineralised (DM) water export for heavy water plant and urea plant which was having deuterium rich DM water connection was connected with DM water of urea plant which is not rich in deuterium, (ii)Sample cooler pump suction was connected with raw water, (iii)Ammonia plant line No.II condensate stripper was rectified during annual shut down to avoid excessive steam venting from its top and other draining, and (iv)Stripper condensate directly connected to make up water bypassing open settler to avoid evaporation and diffusion losses. With these modifications the deuterium concentration in feed synthesis gas improved to about 105 ppm. To improve it to 115 ppm, further modifications are suggested. (author). 5 figs

NMR analysis of t-butyl-catalyzed deuterium exchange at unactivated arene localities.

Science.gov (United States)

Stack, Douglas E; Eastman, Rachel

2016-10-01

Regioselective labelling of arene rings via electrophilic exchange is often dictated by the electronic environment caused by substituents present on the aromatic system. Previously, we observed the presence of a t-butyl group, either covalently bond or added as an external reagent, could impart deuterium exchange to the unactivated, C1-position of estrone. Here, we provide nuclear magnetic resonance analysis of this exchange in a solvent system composed of 50:50 trifluoroacetic acid and D 2 O with either 2-t-butylestrone or estrone in the presence of t-butyl alcohol has shed insights into the mechanism of this t-butyl-catalyzed exchange. Fast exchange of the t-butyl group concurrent with the gradual reduction of the H1 proton signal in both systems suggest a mechanism involving ipso attack of the t-butyl position by deuterium. The reversible addition/elimination of the t-butyl group activates the H1 proton towards exchange by a mechanism of t-butyl incorporation, H1 activation and exchange, followed by eventual t-butyl elimination. Density functional calculations are consistent with the observation of fast t-butyl exchange concurrent with slower H1 exchange. The σ-complex resulting from ipso attack of deuterium at the t-butyl carbon was 6.6 kcal/mol lower in energy than that of the σ-complex resulting from deuterium attack at C1. A better understanding of the t-butyl-catalyzed exchange could help in the design of labelling recipes for other phenolic metabolites. Copyright © 2016 The Authors. Journal of Labelled Compounds and Radiopharmaceuticals published by John Wiley & Sons, Ltd.

Exploring the Origins of Deuterium Enrichments in Solar Nebular Organics

Science.gov (United States)

Cleeves, L. Ilsedore; Bergin, Edwin A.; O'D. Alexander, Conel M.; Du, Fujun; Graninger, Dawn; Öberg, Karin I.; Harries, Tim J.

2016-03-01

Deuterium-to-hydrogen (D/H) enrichments in molecular species provide clues about their original formation environment. The organic materials in primitive solar system bodies generally have higher D/H ratios and show greater D/H variation when compared to D/H in solar system water. We propose this difference arises at least in part due to (1) the availability of additional chemical fractionation pathways for organics beyond that for water, and (2) the higher volatility of key carbon reservoirs compared to oxygen. We test this hypothesis using detailed disk models, including a sophisticated, new disk ionization treatment with a low cosmic-ray ionization rate, and find that disk chemistry leads to higher deuterium enrichment in organics compared to water, helped especially by fractionation via the precursors CH2D+/CH3+. We also find that the D/H ratio in individual species varies significantly depending on their particular formation pathways. For example, from ˜20-40 au, CH4 can reach {{D}}/{{H}}˜ 2× {10}-3, while D/H in CH3OH remains locally unaltered. Finally, while the global organic D/H in our models can reproduce intermediately elevated D/H in the bulk hydrocarbon reservoir, our models are unable to reproduce the most deuterium-enriched organic materials in the solar system, and thus our model requires some inheritance from the cold interstellar medium from which the Sun formed.

Results of neutron irradiation of liquid lithium saturated with deuterium

International Nuclear Information System (INIS)

Tazhibayeva, Irina; Ponkratov, Yuriy; Kulsartov, Timur; Gordienko, Yuriy; Skakov, Mazhyn; Zaurbekova, Zhanna; Lyublinski, Igor; Vertkov, Alexey; Mazzitelli, Giuseppe

2017-01-01

Highlights: • The results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1M research reactor are described. • At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10 9 exp(−144/RT). • The T 2 molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise. - Abstract: This paper describes the results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1 M research reactor. The neutron flux at the reactor core center at 2 MW was 5 10 −13 cm −2 s −1 . The efficiency coefficients of helium and tritium release from lithium saturated with deuterium were calculated. The tritium interaction with lithium atoms (formation and dissociation of lithium tritide) has an effect on tritium release. An increment of sample’s temperature results in tritium release acceleration due to rising of the dissociation rate of lithium tritide. At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10 9 exp(-144/RT). The T 2 molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise.

Deuterium Depth Profile in Neutron-Irradiated Tungsten Exposed to Plasma

International Nuclear Information System (INIS)

Shimada, Masashi; Cao, G.; Hatano, Y.; Oda, T.; Oya, Y.; Hara, M.; Calderoni, P.

2011-01-01

The effect of radiation damage has been mainly simulated using high-energy ion bombardment. The ions, however, are limited in range to only a few microns into the surface. Hence, some uncertainty remains about the increase of trapping at radiation damage produced by 14 MeV fusion neutrons, which penetrate much farther into the bulk material. With the Japan-US joint research project: Tritium, Irradiations, and Thermofluids for America and Nippon (TITAN), the tungsten samples (99.99 % pure from A.L.M.T., 6mm in diameter, 0.2mm in thickness) were irradiated to high flux neutrons at 50 C and to 0.025 dpa in the High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory (ORNL). Subsequently, the neutron-irradiated tungsten samples were exposed to a high-flux deuterium plasma (ion flux: 1021-1022 m-2s-1, ion fluence: 1025-1026 m-2) in the Tritium Plasma Experiment (TPE) at the Idaho National Laboratory (INL). First results of deuterium retention in neutron-irradiated tungsten exposed in TPE have been reported previously. This paper presents the latest results in our on-going work of deuterium depth profiling in neutron-irradiated tungsten via nuclear reaction analysis. The experimental data is compared with the result from non neutron-irradiated tungsten, and is analyzed with the Tritium Migration Analysis Program (TMAP) to elucidate the hydrogen isotope behavior such as retention and depth distribution in neutron-irradiated and non neutron-irradiated tungsten.

Photodisintegration of deuterium and big bang nucleosynthesis

International Nuclear Information System (INIS)

Hara, K.Y.; Utsunomiya, H.; Goko, S.; Akimune, H.; Yamagata, T.; Ohta, M.; Toyokawa, H.; Kudo, K.; Uritani, A.; Shibata, Y.; Lui, Y.-W.; Ohgaki, H.

2003-01-01

Photodisintegration cross sections were measured for deuterium with Laser-Compton scattering γ beams at seven energies near threshold. Combined with the preceding data, R(E)=N a σv for the p(n,γ)D reaction is for the first time evaluated based on experimental data with 6% uncertainty in the energy region relevant to the big bang nucleosynthesis (BBN). The result confirms the theoretical evaluation on which the BBN in the precision era relies

Synthesis of deuterium and tritium labelled tyrosine

International Nuclear Information System (INIS)

Kanska, M.; Drabarek, S.

1980-01-01

A new method of synthesis of tyrosine labelled with deuterium and tritium in the aromatic ring has been developed. Deuterated and tritiated tyrosine was obtained by isotope exchange between tyrosine and deuterated or tritiated water at elevated temperature in hydrochloric acid medium using K 2 PtCl 4 as a catalyst. For synthesis of tritiated tyrosine 1 Ci HTO was used; the specific activity of the product was 5 mCi/mMol. (author)

Lattice dynamics of solid deuterium by inelastic neutron scattering

DEFF Research Database (Denmark)

Nielsen, Mourits; Bjerrum Møller, Hans

1971-01-01

The dispersion relations for phonons in solid ortho-deuterium have been measured at 5 °K by inelastic neutron scattering. The results are in good agreement with recent calculations in which quantum effects are taken into account. The data have been fitted to a third-neighbor general force model...

Fusion Neutronic Source deuterium endash tritium neutron spectrum measurements using natural diamond detectors

International Nuclear Information System (INIS)

Krasilnikov, A.V.; Kaneko, J.; Isobe, M.; Maekawa, F.; Nishitani, T.

1997-01-01

Two natural diamond detectors (NDDs) operating at room temperature were used for Fusion Neutronics Source (FNS) deuterium endash tritium (DT) neutron spectra measurements at different points around the tritium target and for different deuteron beam energies. Energy resolution of both NDDs were measured, with values 1.95% and 2.8%. Due to the higher energy resolution of one of the two NDDs studied it was possible to measure the shape of the DT neutron energy distribution and its broadening due to deuteron scattering inside the target. The influence of pulse pileup on the energy resolution of the combined system (NDD+electronics) at count rates up to 3.8x10 5 counts/s was investigated. A 3.58% energy resolution for the spectrometric system based on NDD and a 0.25 μs shaping time amplifier has been measured at a count rate of 5.7x10 5 counts/s. It is shown that special development of a fast pulse signal processor is necessary for NDD based spectrometry at count rates of approximately 10 6 counts/s. copyright 1997 American Institute of Physics

Deuterium isotope effect on the intramolecular electron transfer in Pseudomonas aeruginosa azurin

DEFF Research Database (Denmark)

Farver, O.; Zhang, Jingdong; Chi, Qijin

2001-01-01

rather than negative. Isotope effects are, however, also inherent in the nuclear reorganization Gibbs free energy and in the tunneling factor for the electron transfer process. A slightly larger thermal protein expansion in H2O than in D2O (0.001 nm K-1) is sufficient both to account for the activation......Intramolecular electron transfer in azurin in water and deuterium oxide has been studied over a broad temperature range. The kinetic deuterium isotope effect, k(H)/k(D), is smaller than unity (0.7 at 298 K), primarily caused by the different activation entropies in water (-56.5 J K-1 mol(-1...

Apparatus and process for deuterium exchange

International Nuclear Information System (INIS)

Ergenc, M.S.

1976-01-01

The deuterium exchange plant is combined with an absorption refrigeration plant in order to improve the exchange process and to produce refrigeration. The refrigeration plant has a throttling means for expanding and cooling a portion of the liquid exchange medium separated in the exchange plant as well as an evaporator, in which the said liquid exchange medium is brought into heat exchange with a cold consumer device, absorption means for forming a solution of the used exchange medium and fresh water and a pump for pumping the solution into the exchange plant

Laser-driven polarized H/D sources and targets

International Nuclear Information System (INIS)

Clasie, B.; Crawford, C.; Dutta, D.; Gao, H.; Seely, J.; Xu, W.

2005-01-01

Traditionally, Atomic Beam Sources are used to produce targets of nuclear polarized hydrogen (H) or deuterium (D) for experiments using storage rings. Laser-Driven Sources (LDSs) offer a factor of 20-30 gain in the target thickness (however, with lower polarization) and may produce a higher overall figure of merit. The LDS is based on the technique of spin-exchange optical pumping where alkali vapor is polarized by absorbing circularly polarized laser photons. The H or D atoms are nuclear-polarized through spin-exchange collisions with the polarized alkali vapor and through subsequent hyperfine interactions during frequent H-H or D-D collisions

Syntheses of α and γ-tocopherols selectively labelled with deuterium

International Nuclear Information System (INIS)

Hughes, L.; Slaby, M.; Burton, G.W.; Ingold, K.U.

1990-01-01

Four deuterium-substituted α-tocopherols (dideutero-RRR, nonadeutero-ambo, nonadeutero-all-rac and undecadeutero-all-rac) and a dideutro-RRR-γ-tocopherol have been synthesized for use in studies of the biokinetics, bioavailability and metabolism of vitamin E. (author)

Polarized internal targets for electronuclear experiments

International Nuclear Information System (INIS)

van den Brand, J.F.J.

1993-01-01

Polarized internal gas targets represent a unique opportunity for the measurement of spin observables in electro-nuclear physics. Two measurements will be discussed. First, spin observables have been measured in elastic and quasi-free scattering of 45, 200, 300, and 415 MeV polarized protons from a polarized 3 He internal gas target at the Indiana University Cyclotron Facility Cooler Ring. The data obtained constitute the first measurement of spin correlation parameters using a storage ring with polarized beam and polarized internal gas target. Second, a quasi-free (e,e'p) experiment using tensor polarized deuterium will be discussed. Here, the goal is the measurement of the S- and D-state parts of the proton spectral function by scattering 700 MeV electrons from an atomic beam source. Large acceptance detectors have been used in both experiments. The internal-target technique has broad applicability in nuclear and particle physics

Use of Fourier transformed infrared spectrophotometer (FTIR) for determination of breastmilk output by the deuterium dilution method among Senegalese women

International Nuclear Information System (INIS)

Sarr Cisse, Aita; Diaham, Babou; Dossou, Nicole; Guiro, Amadou Tidiane; Wade, Salimata; Bluck, Leslie

2002-01-01

Breastmilk output can be estimated from the mother's total body water and water turnover rates after oral administration of deuterium oxide. Usually the deuterium enrichments are determined using a isotope ratio mass spectrometer, which is expensive and requires a specialist for operation and maintenance. Such equipment is dfficult to set up in developing countries. A less expensive method was developed which uses a Fourier transform infrared spectrophotometer (FTIR) for deuterium enrichment analysis. This study evaluated the constraints of using FTIR to study lactating women in Senegal. The deuterium isotope method was found to be adequate for free living subjects and presented few constraints except for the duration of the saliva sampling (14 days). The method offers the opportunity to determine simultaneously breastmilk output, mother's body composition, and breastfeeding practices. Deuterium sample enrichments measured with FTIR were fast and easy, but for spectrum quality some environmental control is required to optimize the results. (Authors)

Ion Mobility Spectrometry-Hydrogen Deuterium Exchange Mass Spectrometry of Anions: Part 2. Assessing Charge Site Location and Isotope Scrambling

Science.gov (United States)

Khakinejad, Mahdiar; Ghassabi Kondalaji, Samaneh; Donohoe, Gregory C.; Valentine, Stephen J.

2016-03-01

Ion mobility spectrometry (IMS) coupled with gas-phase hydrogen deuterium exchange (HDX)-mass spectrometry (MS) and molecular dynamic simulations (MDS) has been used for structural investigation of anions produced by electrospraying a sample containing a synthetic peptide having the sequence KKDDDDDIIKIIK. In these experiments the potential of the analytical method for locating charge sites on ions as well as for utilizing collision-induced dissociation (CID) to reveal the degree of deuterium uptake within specific amino acid residues has been assessed. For diffuse (i.e., more elongated) [M - 2H]2- ions, decreased deuterium content along with MDS data suggest that the D4 and D6 residues are charge sites, whereas for the more diffuse [M - 3H]3- ions, the data suggest that the D4, D7, and the C-terminus are deprotonated. Fragmentation of mobility-selected, diffuse [M - 2H]2- ions to determine deuterium uptake at individual amino acid residues reveals a degree of deuterium retention at incorporation sites. Although the diffuse [M - 3H]3- ions may show more HD scrambling, it is not possible to clearly distinguish HD scrambling from the expected deuterium uptake based on a hydrogen accessibility model. The capability of the IMS-HDX-MS/MS approach to provide relevant details about ion structure is discussed. Additionally, the ability to extend the approach for locating protonation sites on positively-charged ions is presented.

A search for parity violation in the inelastic scattering of polarized electrons from deuterium at 19.4 GeV

International Nuclear Information System (INIS)

Prescott, C.Y.; Atwood, W.B.; Cottrell, R.L.A.

1977-01-01

A search for parity violating effects in the inelastic scattering of polarized electrons off an unpolarized deuterium target at 19.4 GeV has recently been performed at SLAC. Using the 20-GeV/c and 8-GeV/c spectrometers, two kinematical points with Q 2 values of 1.2 GeV/c 2 and 4.2 GeV/c 2 , respectively, have been measured. Statistical accuracy of the measurements approaches the level of the weak interactions. Systematic errors are still being studied. Techniques to measure and control systematic errors and the present status of the data analysis are discussed

Laser driven single shock compression of fluid deuterium from 45 to 220 GPa

Energy Technology Data Exchange (ETDEWEB)

Hicks, D; Boehly, T; Celliers, P; Eggert, J; Moon, S; Meyerhofer, D; Collins, G

2008-03-23

The compression {eta} of liquid deuterium between 45 and 220 GPa under laser-driven shock loading has been measured using impedance matching to an aluminum (Al) standard. An Al impedance match model derived from a best fit to absolute Hugoniot data has been used to quantify and minimize the systematic errors caused by uncertainties in the high-pressure Al equation of state. In deuterium below 100 GPa results show that {eta} {approx_equal} 4.2, in agreement with previous impedance match data from magnetically-driven flyer and convergent-explosive shock wave experiments; between 100 and 220 GPa {eta} reaches a maximum of {approx}5.0, less than the 6-fold compression observed on the earliest laser-shock experiments but greater than expected from simple extrapolations of lower pressure data. Previous laser-driven double-shock results are found to be in good agreement with these single-shock measurements over the entire range under study. Both sets of laser-shock data indicate that deuterium undergoes an abrupt increase in compression at around 110 GPa.

A high field optical-pumping spin-exchange polarized deuterium source

International Nuclear Information System (INIS)

Coulter, K.P.; Holt, R.J.; Kinney, E.R.; Kowalczyk, R.S.; Poelker, M.; Potterveld, D.H.; Young, L.; Zeidman, B.; Toporkov, D.

1992-01-01

Recent results from a prototype high field optical-pumping spin-exchange polarized deuterium source are presented. Atomic polarization as high as 62% have been observed with an intensity of 6.3 x 10 17 atoms-sec -1 and 65% dissociation fraction

The influence of interstitial impurities on temperature ranges of deuterium retention in austenitic stainless steel 18Cr10NiTi

International Nuclear Information System (INIS)

Neklyudov, I.M.; Morozov, O.M.; Kulish, V.G.; Zhurba, V.I.; Galytsky, A.G.; Piatenko, E.V.

2009-01-01

The influence of nitrogen, oxygen and helium on the temperature range of deuterium retention in 18Cr10NiTi stainless steel (of AISI304L type) has been investigated. It is demonstrated that the introduction of oxygen, nitrogen or helium into 18Cr10NiTi steel extends the upper limit in the high-temperature range of deuterium retention. It has been found that for 18Cr10NiTi stainless steel, pre-irradiated with helium ions, the increase in the temperature range of deuterium retention occurs in steps: on attainment of helium concentration of ∼0.5 at.% He the temperature range increases by ∼100 K, and on attainment of helium concentration of ∼2.5 at.% He the temperature range increases by ∼350 K. The introduction of oxygen into 18Cr10NiTi stainless steel results in the increase of the temperature range of deuterium retention in the direction of rise in temperature. In the deuterium thermodesorption spectrum, this manifests itself by the occurrence of an additional low-amplitude peak with the maximum temperature T m ∼ 560 K. The introduction of nitric impurity into 18Cr10NiTi stainless steel results in the extension of the temperature range of deuterium retention towards higher temperatures.

The kinetic isotope effect of hydrogen, deuterium and tritium absorbed and desorbed by titanium

International Nuclear Information System (INIS)

Huang Gang; Cao Xiaohua; Long Xinggui

2008-06-01

p-t curves of hydrogen, deuterium and tritium absorption at 550-750 degree C and desorption at 350-550 degree C by titanium were investigated. The rate constants of absorption and desorption for hydrogen, deuterium and tritium on each temperature are determined and the activation energy values obtained by this analysis are (55.6 ± 2.4) kJ·mol -1 , (110.2 ± 3.0) kJ·mol -1 and (155.5 ± 3.2) kJ·mol -1 for absorption and (27.1±0.4) KJ·mol -1 , (42.3 ± 1.9) kJ·mol -1 and (62.1±1.6) kJ·mol -1 for desorption respectively. The activation energy value of tritium absorption is highest which shows titanium tritiation is hardest. The activation energy value of tritium desorption is highest and it also can prove that titanium tritide is stablest. There are remarkable kinetic hydrogen isotope effects when titanium absorb and desorb hydrogen, deuterium and tritium. (authors)

Introduction to body composition assessment using the deuterium dilution technique with analysis of saliva samples by fourier transform infrared spectrometry

International Nuclear Information System (INIS)

2010-01-01

For many years, the IAEA has fostered the more widespread use of stable isotope techniques to assess body composition in different population groups to address priority areas in public health nutrition in Member States. The objective is to support national and regional nutrition projects through both the IAEA's technical cooperation programme and its coordinated research projects. In particular, during the last few years, the increased access to analyses of deuterium enrichment by Fourier transform infrared (FTIR) spectrometry has increased the application of this technique in Africa, Asia and Latin America. This publication was developed by an international group of experts to provide practical, hands-on guidance in the use of this technique in settings where the analysis of deuterium enrichment in saliva samples will be made by FTIR. It is targeted at new users of this technique, for example nutritionists, analytical chemists and other professionals. More detailed information on the theoretical background and the practical application of state of the art methodologies to monitor changes in body composition can be found in an IAEA publication entitled Assessment of Body Composition and Total Energy Expenditure in Humans by Stable Isotope Techniques (IAEA Human Health Series No. 3)

Method to separate and enrich molecules containing deuterium

International Nuclear Information System (INIS)

Benson, S.W.

1978-01-01

Organic molecules having a normal H and D content and the general formula RX, in which R is chosen from ethyl, isopropyl, tert. butyl or cyclopentenyl groups and X is a functional group such as F, Cl, Br or OH and can even be H in the special case of cyclopentene, are exposed to an infra-red laser radiation. By careful adjustment, bundling and pulsing of an infrared laser, D-contained RX molecules exposed to the laserbeam, can dissociate or decompose. A D-contained olefin and HX is formed under suitable conditions after exposure to laser radiation. The D-contained olefin is drawn off and combusted to obtain D-contained water or D-contained hydrogen. The non-decomposed or non-reacted RX molecules which are deuterium-impoverished can be decomposed to deuterium impoverished olefins and HX in a further process step by heating on a catalyst. The latter products can then be separated off and be catylytically exchanged with normal water in order to reproduce the normal isotopic composition. They may then where necessary be catalytically recombined to form normal RX which can be recycled. (GG) [de

The Impact of Nonequilibrium and Equilibrium Fractionation on Two Different Deuterium Excess Definitions

Science.gov (United States)

Dütsch, Marina; Pfahl, Stephan; Sodemann, Harald

2017-12-01

The deuterium excess (d) is a useful measure for nonequilibrium effects of isotopic fractionation and can therefore provide information about the meteorological conditions in evaporation regions or during ice cloud formation. In addition to nonequilibrium fractionation, two other effects can change d during phase transitions. The first is the dependence of the equilibrium fractionation factors on temperature, and the second is the nonlinearity of the δ scale on which d is defined. The second effect can be avoided by using an alternative definition that is based on the logarithmic scale. However, in this case d is not conserved when air parcels mix, which can lead to changes without phase transitions. Here we provide a systematic analysis of the benefits and limitations of both deuterium excess definitions by separately quantifying the impact of the nonequilibrium effect, the temperature effect, the δ-scale effect, and the mixing effect in a simple Rayleigh model simulating the isotopic composition of air parcels during moist adiabatic ascent. The δ-scale effect is important in depleted air parcels, for which it can change the sign of the traditional deuterium excess in the remaining vapor from negative to positive. The alternative definition mainly reflects the nonequilibrium and temperature effect, while the mixing effect is about 2 orders of magnitude smaller. Thus, the alternative deuterium excess definition appears to be a more accurate measure for nonequilibrium effects in situations where moisture is depleted and the δ-scale effect is large, for instance, at high latitudes or altitudes.

Heat generation above break-even from laser-induced fusion in ultra-dense deuterium

Directory of Open Access Journals (Sweden)

Leif Holmlid

2015-08-01

Full Text Available Previous results from laser-induced processes in ultra-dense deuterium D(0 give conclusive evidence for ejection of neutral massive particles with energy >10 MeV u−1. Such particles can only be formed from nuclear processes like nuclear fusion at the low laser intensity used. Heat generation is of interest for future fusion energy applications and has now been measured by a small copper (Cu cylinder surrounding the laser target. The temperature rise of the Cu cylinder is measured with an NTC resistor during around 5000 laser shots per measured point. No heating in the apparatus or the gas feed is normally used. The fusion process is suboptimal relative to previously published studies by a factor of around 10. The small neutral particles HN(0 of ultra-dense hydrogen (size of a few pm escape with a substantial fraction of the energy. Heat loss to the D2 gas (at <1 mbar pressure is measured and compensated for under various conditions. Heat release of a few W is observed, at up to 50% higher energy than the total laser input thus a gain of 1.5. This is uniquely high for the use of deuterium as fusion fuel. With a slightly different setup, a thermal gain of 2 is reached, thus clearly above break-even for all neutronicity values possible. Also including the large kinetic energy which is directly measured for MeV particles leaving through a small opening gives a gain of 2.3. Taking into account the lower efficiency now due to the suboptimal fusion process, previous studies indicate a gain of at least 20 during long periods.

Efficient source for the production of ultradense deuterium D(-1) for laser-induced fusion (ICF)

International Nuclear Information System (INIS)

Andersson, Patrik U.; Loenn, Benny; Holmlid, Leif

2011-01-01

A novel source which simplifies the study of ultradense deuterium D(-1) is now described. This means one step further toward deuterium fusion energy production. The source uses internal gas feed and D(-1) can now be studied without time-of-flight spectral overlap from the related dense phase D(1). The main aim here is to understand the material production parameters, and thus a relatively weak laser with focused intensity ≤10 12 W cm -2 is employed for analyzing the D(-1) material. The properties of the D(-1) material at the source are studied as a function of laser focus position outside the emitter, deuterium gas feed, laser pulse repetition frequency and laser power, and temperature of the source. These parameters influence the D(-1) cluster size, the ionization mode, and the laser fragmentation patterns.

Efficient source for the production of ultradense deuterium D(-1) for laser-induced fusion (ICF)

Science.gov (United States)

Andersson, Patrik U.; Lönn, Benny; Holmlid, Leif

2011-01-01

A novel source which simplifies the study of ultradense deuterium D(-1) is now described. This means one step further toward deuterium fusion energy production. The source uses internal gas feed and D(-1) can now be studied without time-of-flight spectral overlap from the related dense phase D(1). The main aim here is to understand the material production parameters, and thus a relatively weak laser with focused intensity ≤1012 W cm-2 is employed for analyzing the D(-1) material. The properties of the D(-1) material at the source are studied as a function of laser focus position outside the emitter, deuterium gas feed, laser pulse repetition frequency and laser power, and temperature of the source. These parameters influence the D(-1) cluster size, the ionization mode, and the laser fragmentation patterns.

Measurements of neutron intensity from liquid deuterium moderator of the cold neutron source of KUR

International Nuclear Information System (INIS)

Kawai, Takeshi; Ebisawa, Toru; Akiyoshi, Tsunekazu; Tasaki, Seiji

1990-01-01

The neutron spectra from the liquid deuterium moderator of the cold neutron source of KUR were measured by the time of flight (TOF) method similar to the previous measurements for the liquid hydrogen moderator. The cold neutron gain factor is found to be about 20 ∼ 28 times for the wavelength longer than 6 A. Cold neutron intensities from the liquid deuterium moderator and from the liquid hydrogen moderator are compared and discussed. (author)

Electrolytic installation in order to obtain deuterium and to fill the pressure deposits

International Nuclear Information System (INIS)

Cordero Lopez, F.; Tanarro Sanz, A.

1959-01-01

In order to obtain deuterium to feed the ion sources of the accelerators an easy and automatic electrolytic installation has been prepared. this installation and a small compressor designed and constructed for this purpose permit to fill deposits of 1 or 2 liters capacity with deuterium, till a 4 atmosphere pressure in few hours of operation. The electrolytic cell has V shape and permits operation with 3 cc heavy water only as it has small dead volume; the electrodes are platinum and as electrolyte an OH Na solution in a proportion of 15 w/o is used. (Author) 3 refs

Use of deuterium n. m. r. spectroscopy in mechanistic studies of exchange reactions of ethers on supported metal catalysts

Energy Technology Data Exchange (ETDEWEB)

Campbell, J.A.; Kemball, Charles; McDougall, G.S.

1987-10-01

Exchange reactions of diethyl ether (DEE) and tetrahydrofuran (THF) with deuterium have been studied over supported nickel, palladium, platinum, and rhodium catalysts. Products from most of the systems were analysed by deuterium n.m.r. spectroscopy (55.28 MHz) which gave quantitative results about the distribution of deuterium in the exchanged ethers. The results confirm earlier conclusions about the mechanism of the exchange of DEE and provide new evidence about the reactions of THF. Some hydrogenolysis occurred simultaneously with exchange of THF over both nickel and platinum.

Design problems of a continuous injector of many amperes of MeV deuterium neutrals

International Nuclear Information System (INIS)

Fink, J.H.

1976-10-01

A continuous injector of many amperes of MeV deuterium neutrals will require high currents of negative deuterium ions to be generated, accelerated and stripped of electrons by methods that are not fully developed. Each of these processes as briefly described in this report, introduce constraints upon the ion optics, beam line pumping, and high voltage stand-off that must be mutually resolved. Although the design of such an injector represents a difficult task, there is no fundamental reason that very high current beams cannot be handled

Synthesis of deuterium-labelled compounds for FOTEK project

International Nuclear Information System (INIS)

Joergensen, O.; Egsgaard, H.; Larsen, E.

1996-01-01

In the FoTech project there have been utilized labelled compounds of stable isotopes as internal standards. Some of these compounds are commercially available ( 13 C-labelled PCB congeners, 13 C-labelled diethylstilbestrol for determination of anabolic steroids). Others, like D 9 -clenbuterol, D 3 -clenbuterol, D 3 -zeramol and D 3 -dimetridazol have been synthesized. General aspects of deuterium compounds labelling are considered. (EG)

Heat evolution involved with electrochemical discharge of hydrogen and deuterium onto palladium

International Nuclear Information System (INIS)

Chemla, M.; Chevalet, J.; Bury, R.

1989-01-01

Using a quasi-adiabatic micro-calorimeter, we could determine the thermal energy generated during electrolysis of a 0.2 M solution of LiO D in heavy water. In all cases of usual electrolysis, the heat production was found to be less than the total input of electrical energy. We also applied a new technique of transfer electrolysis, where a sample of deuterium saturated palladium was used as the anode. Then, the thermal energy is strictly equal to the consumed electrical energy. In a few experiments, a slight excess of enthalpy was observed and was assumed to result from partial oxidation of deuterium by trace amounts of oxygen. Similar experiments using natural water lead to comparable results [fr

Results of neutron irradiation of liquid lithium saturated with deuterium

Energy Technology Data Exchange (ETDEWEB)

Tazhibayeva, Irina, E-mail: tazhibayeva@ntsc.kz [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Ponkratov, Yuriy; Kulsartov, Timur; Gordienko, Yuriy; Skakov, Mazhyn; Zaurbekova, Zhanna [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Lyublinski, Igor [JSC «Red Star», Moscow (Russian Federation); NRNU «MEPhI», Moscow (Russian Federation); Vertkov, Alexey [JSC «Red Star», Moscow (Russian Federation); Mazzitelli, Giuseppe [ENEA, RC Frascati, Frascati (Italy)

2017-04-15

Highlights: • The results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1M research reactor are described. • At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10{sup 9} exp(−144/RT). • The T{sub 2} molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise. - Abstract: This paper describes the results on neutron irradiation of liquid lithium saturated with deuterium at the IVG.1 M research reactor. The neutron flux at the reactor core center at 2 MW was 5 10{sup −13} cm{sup −2} s{sup −1}. The efficiency coefficients of helium and tritium release from lithium saturated with deuterium were calculated. The tritium interaction with lithium atoms (formation and dissociation of lithium tritide) has an effect on tritium release. An increment of sample’s temperature results in tritium release acceleration due to rising of the dissociation rate of lithium tritide. At temperatures below 573 K the efficiency coefficient of tritium release is well described by the expression K = 0.015 exp(−14/RT), and above 623 K − K = 10{sup 9} exp(-144/RT). The T{sub 2} molecules contribution into the overall tritium release becomes apparent at temperatures higher than 673 K and increases with the temperature rise.

Re-emission and thermal desorption of deuterium from plasma sprayed tungsten coatings for application in ASDEX-upgrade

International Nuclear Information System (INIS)

Garcia-Rosales, C.; Franzen, P.; Plank, H.; Roth, J.; Gauthier, E.

1996-01-01

The trapping and release of deuterium implanted with an energy of 100 eV in wrought and in plasma sprayed tungsten of different manufacture and structure has been investigated by means of re-emission as well as thermal and isothermal desorption spectroscopy. The experimental data for wrought tungsten are compared with model calculations with the PIDAT code in order to estimate the parameters governing diffusion, surface recombination and trapping in tungsten. The amount of retained deuterium in tungsten is of the same order of magnitude as in graphite for the implantation parameters used in this work. The mobile hydrogen concentration in tungsten during the implantation is of the same order of magnitude than the trapped one, being released after the termination of the implantation. The fraction of deuterium trapped to defects increases strongly with the porosity of the samples. The temperature needed for the release of the trapped deuterium (∝600 K) are considerably lower than for graphite, due to the smaller trapping energy (≤1.5 eV). (orig.)

Ion-induced emission of charged particles from solid hydrogen and deuterium

International Nuclear Information System (INIS)

Borgesen, P.; Schou, J.; Sorensen, H.

1980-01-01

Measurements have been made of the emission of both positive and negative particles from solid hydrogen and deuterium for normal incidence of H + , H + 2 , H + 3 , D 2 H + , D + 3 and He + ions up to 10 keV. For positive particles the emission coefficient increased with increasing energy of incidence to reach a value of 0.08 per atom for 10 keV H + onto hydrogen. Apparently the positive particles are sputtered ones. The negative particles emitted are predominantly electrons. The emission coefficient per incident atom as a function of the velocity of the incident particle agress fairly well with results published earlier for incidence of hydrogen and deuterium ions. However, systematic differences of up to 10% are now observed between the coefficients for the different types of ions. (orig.)

Detection of Deuterium in Icy Surfaces and the D/H Ratio of Icy Objects

Science.gov (United States)

Clark, Roger Nelson; Brown, Robert H.; Swayze, Gregg A.; Cruikshank, Dale P.

2017-10-01

Water ice in crystalline or amorphous form is orientationally disordered, which results in very broad absorptions. Deuterium in trace amounts goes into an ordered position, so is not broadened like H2O absorptions. The D-O stretch is located at 4.13 microns with a width of 0.027 micron. Laboratory spectral measurements on natural H2O and deuterium doped ice show the absorption is slightly asymmetric and in reflectance the band shifts from 4.132 to 4.137 microns as abundance decreases. We derive a preliminary absorption coefficient of ~ 80,000 cm^-1 for the D-O stretch compared to about 560 cm^-1 in H2O ice at 4.13 microns, enabling the detection of deuterium at levels less than Vienna Standard Mean Ocean Water (VSMOW), depending on S/N. How accurate the D/H ratios can be derived will require additional lab work and radiative transfer modeling to simultaneously derive the grain size distribution, the abundance of any contaminants, and deuterium abundance. To first order, the grain size distribution can be compensated by computing the D-O stretch band depth to 2-micron H2O ice band depth ratio, which we call Dratio. Colorado fresh water (~80% of VSMOW) has a Dratio of 0.036, at a D/H = 0.0005, the Dratio = 0.15, and at a D/H = 0.0025, the Dratio = 0.42. The VSMOW Dratio is ~ 0.045.We have used VIMS data from the Cassini spacecraft to compute large spectral averages to detect the deuterium in the rings and on the icy satellite surfaces. A B-ring, 21,882 pixel average, at 640 ms/pixel, or 3.89 hours of integration time, shows a 3.5% O-D stretch band depth and a Dratio = 0.045, indicating deuterium abundance equal to VSMOW. Rhea, using 1.89 hours of integration time shows Dratio = 0.052, or slightly higher than VSMOW. Phoebe has an unusually deep O-D stretch band of 1.85% considering the high abundance of dark material suppressing the ice absorptions. We measure a Dratio = 0.11, an enhancement of ~2.4 over VSMOW, but detailed radiative transfer modeling is needed to

Steady-state and transient hydrocarbon production in graphite by low energy impact of atomic and molecular deuterium projectiles

International Nuclear Information System (INIS)

Zhang, H.; Meyer, F.W.

2009-01-01

We report measurements of steady-state yields of methyl, methane and heavier hydrocarbons for deuterium atomic and molecular ions incident on ATJ graphite, HOPG, and a-C:D thin films in the energy range 10-200 eV/D. The yields were determined using a QMS technique in conjunction with calibrated hydrocarbon leaks. We have also studied transient hydrocarbon production and hydrogen (deuterium) re-emission for 80 and 150 eV/D D + , D 2 + , and D 3 + projectiles incident on ATJ graphite surfaces pre-loaded to steady state by 20 eV/D beams of the corresponding species. Immediately after starting the higher-energy beams, transient hydrocarbon and D 2 re-emission yields significantly larger than steady-state values were observed, which exponentially decayed as a function of beam fluence. The initial yield values were related to the starting hydrocarbon and deuterium densities in the prepared sample, while the exponential decay constants provided information on the hydrocarbon kinetic release and hydrogen (deuterium) detrapping cross-sections.

Use of deuterium oxide to measure breast milk intake in children aged 7-12 months receiving complementary foods

International Nuclear Information System (INIS)

Creed-Kanashiro, H.

2000-01-01

In the present study we performed a pilot study using deuterium oxide method to determine the breast-milk intake in children 7-12 months of age receiving complementary food. This is applied to a community efficacy study to determine the effects on total energy and nutrient intake and on breast-milk consumption of an intensive education intervention using locally available, culturally acceptable complementary foods. We determined the washout period for the deuterium finding a value of 21 days for the mother and child. This measurement was performed using the infrared spectrometer of the Instituto de Investigacion Nutricional and compared with the values obtained with the IR Mass Spectrometer of INTA Chile. The test weighing was conduced on 14 children and compared with the values obtained using the deuterium methodology. Our result suggest that the breast milk intake determined by the weighing test was lower with regard to the value obtained with the deuterium methodology. (author)

Use of deuterium oxide to measure breast milk intake in children aged 7-12 months receiving complementary foods

Energy Technology Data Exchange (ETDEWEB)

Creed-Kanashiro, H [Instituto de Investigacion Nutricional, La Molina, Lima (Peru)

2000-07-01

In the present study we performed a pilot study using deuterium oxide method to determine the breast-milk intake in children 7-12 months of age receiving complementary food. This is applied to a community efficacy study to determine the effects on total energy and nutrient intake and on breast-milk consumption of an intensive education intervention using locally available, culturally acceptable complementary foods. We determined the washout period for the deuterium finding a value of 21 days for the mother and child. This measurement was performed using the infrared spectrometer of the Instituto de Investigacion Nutricional and compared with the values obtained with the IR Mass Spectrometer of INTA Chile. The test weighing was conduced on 14 children and compared with the values obtained using the deuterium methodology. Our result suggest that the breast milk intake determined by the weighing test was lower with regard to the value obtained with the deuterium methodology. (author)

Intense Non-Linear Soft X-Ray Emission from a Hydride Target during Pulsed D Bombardment

Science.gov (United States)

Miley, George H.; Yang, Yang; Lipson, Andrei; Haque, Munima; Percel, Ian; Romer, Michael

Radiation emission from low-energy nuclear radiation (LENR) electrodes (both charged-particle and X-rays) represents an important feature of LENR in general. Here, calibration, measurement techniques, and soft X-ray emission results from deuterium bombardment of a Pd target (cathode) placed in a pulsed deuterium glow discharge (PGD) are described. An X-ray intensity of 13.4 mW/cm2 and a dose of 3.3 μJ/cm2 were calculated over a 0.5 ms pulse time from AXUV photodiode radiation detector measurements. A most striking feature is that X-ray energies >600 V are observed with a discharge voltage only about half of that value. To further investigate this phenomenon, emission during room temperature D-desorption from electrolytically loaded Pd:Dx cathodes was also studied. The X-ray emission energy observed was quite similar to the PGD case. However, the intensity in this case was almost 13 orders of magnitude lower due to the much lower deuterium fluxes involved.

Intense non-linear soft X-ray emission from a hydride target during pulsed D bombardment

International Nuclear Information System (INIS)

Miley, George H.; Yang, Yang; Lipson, Andrei; Haque, Munima; Percel, Ian; Romer, Michael

2006-01-01

Radiation emission from low-energy nuclear radiation (LENR) electrodes (both charged-particle and X-rays) represents an important feature of LENR in general. Here, calibration, measurement techniques, and soft X-ray emission results from deuterium bombardment of a Pd target (cathode) placed in a pulsed deuterium glow discharge (PGD) are described. An X-ray intensity of 13.4 mW/cm 2 and a dose of 3.3 μJ/cm 2 were calculated over a 0.5 ms pulse time from AXUV photodiode radiation detector measurements. A most striking feature is that X-ray energies >600 V are observed with a discharge voltage only about half of that value. To further investigate this phenomenon, emission during room temperature D-desorption from electrolytically loaded Pd:Dx cathodes was also studied. The X-ray emission energy observed was quite similar to the PGD case. However, the intensity in this case was almost 13 orders of magnitude lower due to the much lower deuterium fluxes involved. (author)

Status of the hydrogen and deuterium atomic beam polarized target for NEPTUN experiment

International Nuclear Information System (INIS)

Balandikov, N.I.; Ershov, V.P.; Fimushkin, V.V.; Kulikov, M.V.; Pilipenko, Y.K.; Shutov, V.B.

1995-01-01

NEPTUN-NEPTUN-A is a polarized experiment at Accelerating and Storage Complex (UNK, IHEP) with two internal targets. Status of the atomic beam polarized target that is being developed at the Joint Institute for Nuclear Research, Dubna is presented. copyright 1995 American Institute of Physics

[Influence of deuterium depleted water on freeze-dried tissue isotopic composition and morphofunctional body performance in rats of different generations].

Science.gov (United States)

Dzhimak, S S; Baryshev, M G; Basov, A A; Timakov, A A

2014-01-01

The influence of deuterium depleted water on the body of different rats generations was investigated in physiological conditions. As a result of this study it was established that the most significant and rapid reduction in D/H equilibrium was observed in plasma (by 36.2%), and lyophilized kidney tissues (by 15.8%). Less pronounced deuterium decrease was characteristic of liver tissue (9.3%) and heart (8.5%). Stabilization of the isotopic exchange reaction rate was fixed in the blood and tissues of rats, starting from the second generation. At the same time when deuterium depleted water (40 ppm) was used in dietary intake, the change in morphological and functional parameters in laboratory animals associated with the processes of adaptation to the effects of substress isotopic D/H gradient was also noted. The study shows that modification of:only drinking water intake regime can't significantly change the deuterium content in tissues of metabolically active organs, because of the concurrent deuterium receipt in food substances of plant and animal origin.

Deuterium isotope composition of palaeoinfiltration water trapped in speleothems

International Nuclear Information System (INIS)

Rozanski, K.

1987-05-01

Analytical and methodological aspects of combined isotope investigations of carbonate cave deposits are thoroughly discussed in the report. Weight is put on isotope analyses of fluid inclusions (D and 18 O content) extracted from speleothems of known age. Dating was done by the 230 Th/ 234 U ratio method. Isotopic analyses of speleothems originating from European caves allowed some important conclusions to be formulated regarding past climatic and environmental conditions prevailing over the European continent during the last 300,000 yrs: a) δD values of fluid inclusions suggest a remarkable constancy of the heavy-isotope content of European palaeoinfiltration waters recharged during interglacial periods, b) a climate-induced, long-term changes in isotopic composition of precipitation and surface air temperature over Europe can be characterized by the deuterium gradient of ca.1 4 deg./oo/deg. C, c) an apparent constancy of the continental gradient in deuterium content of European palaeoinfiltration waters as judged from the fluid inclusion data suggests that atmospheric circulation over Europe did not undergo substantial changes for at least 300,000 years

Fast ignition upon the implosion of a thin shell onto a precompressed deuterium-tritium ball

Science.gov (United States)

Gus'kov, S. Yu.; Zmitrenko, N. V.

2012-11-01

Fast ignition of a precompressed inertial confinement fusion (ICF) target by a hydrodynamic material flux is investigated. A model system of hydrodynamic objects consisting of a central deuterium-tritium (DT) ball and a concentric two-layer shell separated by a vacuum gap is analyzed. The outer layer of the shell is an ablator, while the inner layer consists of DT ice. The igniting hydrodynamic flux forms as a result of laser-driven acceleration and compression of the shell toward the system center. A series of one-dimensional numerical simulations of the shell implosion, the collision of the shell with the DT ball, and the generation and propagation of thermonuclear burn waves in both parts of the system are performed. Analytic models are developed that describe the implosion of a thin shell onto a central homogeneous ball of arbitrary radius and density and the initiation and propagation of a thermonuclear burn wave induced by such an implosion. Application of the solution of a model problem to analyzing the implosion of a segment of a spherical shell in a conical channel indicates the possibility of fast ignition of a spherical ICF target from a conical target driven by a laser pulse with an energy of 500-700 kJ.

Effect of periodic deuterium ion irradiation on deuterium retention and blistering in Tungsten

Directory of Open Access Journals (Sweden)

M. Oya

2017-08-01

Full Text Available The effect of periodic irradiation on Deuterium (D retention and blistering in Tungsten (W was investigated. W samples were exposed to D plasma at a fixed fluence while varying the irradiation cycle number (1-shot, 2-shots and 3-shots. Exposure energy and flux were ∼50eV and ∼1 ×1022 D m−2 s−1, respectively. Sample temperatures were 537K and 643K. At 573K, D retention and blister density decreased with increasing number of irradiation cycle. In contrast at 643K, D retention showed no dependence on number of irradiation cycle. Therefore, sample temperature during irradiation is an important parameter in comparing the results of continuous and periodic irradiation, especially in studies involving extremely-high-flux (>1024 D m−2 s−1 irradiation and fluence dependency of D retention.

Heterogeneous Catalysis: Deuterium Exchange Reactions of Hydrogen and Methane