WorldWideScience

Sample records for design studies based

  1. Tile-based rigidization surface parametric design study

    Science.gov (United States)

    Giner Munoz, Laura; Luntz, Jonathan; Brei, Diann; Kim, Wonhee

    2018-03-01

    Inflatable technologies have proven useful in consumer goods as well as in more recent applications including civil structures, aerospace, medical, and robotics. However, inflatable technologies are typically lacking in their ability to provide rigid structural support. Particle jamming improves upon this by providing structures which are normally flexible and moldable but become rigid when air is removed. Because these are based on an airtight bladder filled with loose particles, they always occupy the full volume of its rigid state, even when not rigidized. More recent developments in layer jamming have created thin, compact rigidizing surfaces replacing the loose volume of particles with thinly layered surface materials. Work in this area has been applied to several specific applications with positive results but have not generally provided the broader understanding of the rigidization performance as a function of design parameters required for directly adapting layer rigidization technology to other applications. This paper presents a parametric design study of a new layer jamming vacuum rigidization architecture: tile-based vacuum rigidization. This form of rigidization is based on layers of tiles contained within a thin vacuum bladder which can be bent, rolled, or otherwise compactly stowed, but when deployed flat, can be vacuumed and form a large, flat, rigid plate capable of supporting large forces both localized and distributed over the surface. The general architecture and operation detailing rigidization and compliance mechanisms is introduced. To quantitatively characterize the rigidization behavior, prototypes rigidization surfaces are fabricated and an experimental technique is developed based on a 3-point bending test. Performance evaluation metrics are developed to describe the stiffness, load-bearing capacity, and internal slippage of tested prototypes. A set of experimental parametric studies are performed to better understand the impact of

  2. Designing Web-Based Educative Curriculum Materials for the Social Studies

    Science.gov (United States)

    Callahan, Cory; Saye, John; Brush, Thomas

    2013-01-01

    This paper reports on a design experiment of web-based curriculum materials explicitly created to help social studies teachers develop their professional teaching knowledge. Web-based social studies curriculum reform efforts, human-centered interface design, and investigations into educative curriculum materials are reviewed, as well as…

  3. Feasibility design study. Land-based OTEC plants. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brewer, J. H.; Minor, J.; Jacobs, R.

    1979-01-01

    The purpose of this study has been to determine the feasibility of installing 10 MWe (MegaWatt-electric) and 40 MWe land-based OTEC demonstration power plants at two specific sites: Keahole Point on the western shore of the island of Hawaii; and Punta Tuna, on the southeast coast of the main island of Puerto Rico. In addition, the study has included development of design parameters, schedules and budgets for the design, construction and operation of these plants. Seawater systems (intake and discharge pipes) were to be sized so that flow losses were equivalent to those expected with a platform-based OTEC power plant. The power module (components and general arrangement was established based on the TRW design. Results are presented in detail. (WHK)

  4. A Competence-Based Curriculum Design for Entrepreneurship Study Program

    Directory of Open Access Journals (Sweden)

    Priska J.R. Siagian

    2011-08-01

    Full Text Available Indonesia is affected by global crisis. Increasing the number of entrepreneurs is one of many solutions to increase the economic growth in Indonesia. The number of entrepreneurs in Indonesia to leverage the economic growth is still limited. Entrepreneurs can be prepared through an Entrepreneurship Study Program. Entrepreneurship Study Program attempts to create qualified entrepreneurs who have relevant competences. In order to create a qualified entrepreneurs, the Entrepreneurial Studies Program requires a competency-based curriculum that will support the educational process and provide all the necessary to become future entrepreneurs who can survive through a global challenge. This research aims to design a competence-based curriculum for entrepreneurial study and uses Quality Function Deployment (QFD as the major tool to design the competence-based curriculum. From the QFD process, this research finds core and elective courses for the Entrepreneurship Study Program. The result shows the competences covered by the courses and sequence, credits, and teaching methods for each course. The competences prepared the potential entrepreneurs can be achieved through specific courses which can be acquired within 8 semesters.

  5. Design study of ship based nuclear power reactor

    International Nuclear Information System (INIS)

    Su'ud, Zaki; Fitriyani, Dian

    2002-01-01

    Preliminary design study of ship based nuclear power reactors has been performed. In this study the results of thermohydraulics analysis is presented especially related to behaviour of ship motion in the sea. The reactors are basically lead-bismuth cooled fast power reactors using nitride fuels to enhance neutronics and safety performance. Some design modification are performed for feasibility of operation under sea wave movement. The system use loop type with relatively large coolant pipe above reactor core. The reactors does not use IHX, so that the heat from primary coolant system directly transferred to water-steam loop through steam generator. The reactors are capable to be operated in difference power level during night and noon. The reactors however can also be used totally or partially to produce clean water through desalination of sea water. Due to the influence of sea wave movement the analysis have to be performed in three dimensional analysis. The computation time for this analysis is speeded up using Parallel Virtual Machine (PVM) Based multi processor system

  6. Participatory design based research

    DEFF Research Database (Denmark)

    Dau, Susanne; Bach Jensen, Louise; Falk, Lars

    This poster reveal how participatory design based research by the use of a CoED inspired creative process can be used for designing solutions to problems regarding students study activities outside campus.......This poster reveal how participatory design based research by the use of a CoED inspired creative process can be used for designing solutions to problems regarding students study activities outside campus....

  7. Designing for Diverse Learning: Case Study of Place-Based Learning in Design and Technologies Pre-Service Teacher Education

    Science.gov (United States)

    Best, Marnie; MacGregor, Denise; Price, Deborah

    2017-01-01

    Place-based learning experiences in Design and Technologies education connect people and place with design processes and products. Drawing on place-based learning, this case study shares the experiences of eight final year pre-service Design and Technologies education students from the University of South Australia as they collaborated with…

  8. Towards non-conventional methods of designing register-based epidemiological studies: An application to pediatric research.

    Science.gov (United States)

    Gong, Tong; Brew, Bronwyn; Sjölander, Arvid; Almqvist, Catarina

    2017-07-01

    Various epidemiological designs have been applied to investigate the causes and consequences of fetal growth restriction in register-based observational studies. This review seeks to provide an overview of several conventional designs, including cohort, case-control and more recently applied non-conventional designs such as family-based designs. We also discuss some practical points regarding the application and interpretation of family-based designs. Definitions of each design, the study population, the exposure and the outcome measures are briefly summarised. Examples of study designs are taken from the field of low birth-weight research for illustrative purposes. Also examined are relative advantages and disadvantages of each design in terms of assumptions, potential selection and information bias, confounding and generalisability. Kinship data linkage, statistical models and result interpretation are discussed specific to family-based designs. When all information is retrieved from registers, there is no evident preference of the case-control design over the cohort design to estimate odds ratios. All conventional designs included in the review are prone to bias, particularly due to residual confounding. Family-based designs are able to reduce such bias and strengthen causal inference. In the field of low birth-weight research, family-based designs have been able to confirm a negative association not confounded by genetic or shared environmental factors between low birth weight and the risk of asthma. We conclude that there is a broader need for family-based design in observational research as evidenced by the meaningful contributions to the understanding of the potential causal association between low birth weight and subsequent outcomes.

  9. Study design requirements for RNA sequencing-based breast cancer diagnostics.

    Science.gov (United States)

    Mer, Arvind Singh; Klevebring, Daniel; Grönberg, Henrik; Rantalainen, Mattias

    2016-02-01

    Sequencing-based molecular characterization of tumors provides information required for individualized cancer treatment. There are well-defined molecular subtypes of breast cancer that provide improved prognostication compared to routine biomarkers. However, molecular subtyping is not yet implemented in routine breast cancer care. Clinical translation is dependent on subtype prediction models providing high sensitivity and specificity. In this study we evaluate sample size and RNA-sequencing read requirements for breast cancer subtyping to facilitate rational design of translational studies. We applied subsampling to ascertain the effect of training sample size and the number of RNA sequencing reads on classification accuracy of molecular subtype and routine biomarker prediction models (unsupervised and supervised). Subtype classification accuracy improved with increasing sample size up to N = 750 (accuracy = 0.93), although with a modest improvement beyond N = 350 (accuracy = 0.92). Prediction of routine biomarkers achieved accuracy of 0.94 (ER) and 0.92 (Her2) at N = 200. Subtype classification improved with RNA-sequencing library size up to 5 million reads. Development of molecular subtyping models for cancer diagnostics requires well-designed studies. Sample size and the number of RNA sequencing reads directly influence accuracy of molecular subtyping. Results in this study provide key information for rational design of translational studies aiming to bring sequencing-based diagnostics to the clinic.

  10. Quantification of construction waste prevented by BIM-based design validation: Case studies in South Korea.

    Science.gov (United States)

    Won, Jongsung; Cheng, Jack C P; Lee, Ghang

    2016-03-01

    Waste generated in construction and demolition processes comprised around 50% of the solid waste in South Korea in 2013. Many cases show that design validation based on building information modeling (BIM) is an effective means to reduce the amount of construction waste since construction waste is mainly generated due to improper design and unexpected changes in the design and construction phases. However, the amount of construction waste that could be avoided by adopting BIM-based design validation has been unknown. This paper aims to estimate the amount of construction waste prevented by a BIM-based design validation process based on the amount of construction waste that might be generated due to design errors. Two project cases in South Korea were studied in this paper, with 381 and 136 design errors detected, respectively during the BIM-based design validation. Each design error was categorized according to its cause and the likelihood of detection before construction. The case studies show that BIM-based design validation could prevent 4.3-15.2% of construction waste that might have been generated without using BIM. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Model-based design languages: A case study

    OpenAIRE

    Cibrario Bertolotti, Ivan; Hu, Tingting; Navet, Nicolas

    2017-01-01

    Fast-paced innovation in the embedded systems domain puts an ever increasing pressure on effective software development methods, leading to the growing popularity of Model-Based Design (MBD). In this context, a proper choice of modeling languages and related tools - depending on design goals and problem qualities - is crucial to make the most of MBD benefits. In this paper, a comparison between two dissimilar approaches to modeling is carried out, with the goal of highlighting their relative ...

  12. Designing Home-Based Telemedicine Systems for the Geriatric Population: An Empirical Study.

    Science.gov (United States)

    Narasimha, Shraddhaa; Agnisarman, Sruthy; Chalil Madathil, Kapil; Gramopadhye, Anand; McElligott, James T

    2018-02-01

    Background and Introduction: Telemedicine, the process of providing healthcare remotely using communication devices, has the potential to be useful for the geriatric population when specifically designed for this age group. This study explored the design of four video telemedicine systems currently available and outlined issues with these systems that impact usability among the geriatric population. Based on the results, design suggestions were developed to improve telemedicine systems for this population. Using a between-subjects experimental design, the study considered four telemedicine systems used in Medical University of South Carolina. The study was conducted at a local retirement home. The participant pool consisted of 40 adults, 60 years or older. The dependent measures used were the mean times for telemedicine session initiation and video session, mean number of errors, post-test satisfaction ratings, the NASA-Task Load Index (NASA-TLX) workload measures, and the IBM-Computer Systems Usability Questionnaire measures. Statistical significance was found among the telemedicine systems' initiation times. The analysis of the qualitative data revealed several issues, including lengthy e-mail content, icon placement, and chat box design, which affect the usability of these systems for the geriatric population. Human factor-based design modifications, including short, precise e-mail content, appropriately placed icons, and the inclusion of instructions, are recommended to address the issues found in the qualitative study.

  13. Sequential ensemble-based optimal design for parameter estimation: SEQUENTIAL ENSEMBLE-BASED OPTIMAL DESIGN

    Energy Technology Data Exchange (ETDEWEB)

    Man, Jun [Zhejiang Provincial Key Laboratory of Agricultural Resources and Environment, Institute of Soil and Water Resources and Environmental Science, College of Environmental and Resource Sciences, Zhejiang University, Hangzhou China; Zhang, Jiangjiang [Zhejiang Provincial Key Laboratory of Agricultural Resources and Environment, Institute of Soil and Water Resources and Environmental Science, College of Environmental and Resource Sciences, Zhejiang University, Hangzhou China; Li, Weixuan [Pacific Northwest National Laboratory, Richland Washington USA; Zeng, Lingzao [Zhejiang Provincial Key Laboratory of Agricultural Resources and Environment, Institute of Soil and Water Resources and Environmental Science, College of Environmental and Resource Sciences, Zhejiang University, Hangzhou China; Wu, Laosheng [Department of Environmental Sciences, University of California, Riverside California USA

    2016-10-01

    The ensemble Kalman filter (EnKF) has been widely used in parameter estimation for hydrological models. The focus of most previous studies was to develop more efficient analysis (estimation) algorithms. On the other hand, it is intuitively understandable that a well-designed sampling (data-collection) strategy should provide more informative measurements and subsequently improve the parameter estimation. In this work, a Sequential Ensemble-based Optimal Design (SEOD) method, coupled with EnKF, information theory and sequential optimal design, is proposed to improve the performance of parameter estimation. Based on the first-order and second-order statistics, different information metrics including the Shannon entropy difference (SD), degrees of freedom for signal (DFS) and relative entropy (RE) are used to design the optimal sampling strategy, respectively. The effectiveness of the proposed method is illustrated by synthetic one-dimensional and two-dimensional unsaturated flow case studies. It is shown that the designed sampling strategies can provide more accurate parameter estimation and state prediction compared with conventional sampling strategies. Optimal sampling designs based on various information metrics perform similarly in our cases. The effect of ensemble size on the optimal design is also investigated. Overall, larger ensemble size improves the parameter estimation and convergence of optimal sampling strategy. Although the proposed method is applied to unsaturated flow problems in this study, it can be equally applied in any other hydrological problems.

  14. Repository design sensitivity study: Engineering study report

    International Nuclear Information System (INIS)

    1987-01-01

    A preliminary sensitivity study of the salt repository design has been performed to identify critical site and design parameters to help guide future site characterization and design optimization activities. The study considered the SCP-conceptual design at the Deaf Smith County site in Texas with the horizontal waste package emplacement mode as the base case. Relative to this base case, parameter variations were compared. Limited studies were performed which considered the vertical emplacement mode geometry. The report presents the reference data base and design parameters on which the study was based (including the range of parameters that might be expected). Detailed descriptions of the numerical modeling methods and assumptions are included for the thermal, thermomechanical and hydrogeological analyses. The impacts of parameter variations on the sensitivity of the rock mass response are discussed. Recommendations are provided to help guide site characterization activities and advanced conceptual design optimization activities. 47 refs., 119 refs., 22 tabs

  15. Decision-Based Design Integrating Consumer Preferences into Engineering Design

    CERN Document Server

    Chen, Wei; Wassenaar, Henk Jan

    2013-01-01

    Building upon the fundamental principles of decision theory, Decision-Based Design: Integrating Consumer Preferences into Engineering Design presents an analytical approach to enterprise-driven Decision-Based Design (DBD) as a rigorous framework for decision making in engineering design.  Once the related fundamentals of decision theory, economic analysis, and econometrics modelling are established, the remaining chapters describe the entire process, the associated analytical techniques, and the design case studies for integrating consumer preference modeling into the enterprise-driven DBD framework. Methods for identifying key attributes, optimal design of human appraisal experiments, data collection, data analysis, and demand model estimation are presented and illustrated using engineering design case studies. The scope of the chapters also provides: •A rigorous framework of integrating the interests from both producer and consumers in engineering design, •Analytical techniques of consumer choice model...

  16. GIS-based landscape design research: Stourhead landscape garden as a case study

    Directory of Open Access Journals (Sweden)

    Steffen Nijhuis

    2017-11-01

    Full Text Available Landscape design research is important for cultivating spatial intelligence in landscape architecture. This study explores GIS (geographic information systems as a tool for landscape design research - investigating landscape designs to understand them as architectonic compositions (architectonic plan analysis. The concept ‘composition’ refers to a conceivable arrangement, an architectural expression of a mental construct that is legible and open to interpretation. Landscape architectonic compositions and their representations embody a great wealth of design knowledge as objects of our material culture and reflect the possible treatment of the ground, space, image and program as a characteristic coherence. By exploring landscape architectonic compositions with GIS, design researchers can acquire design knowledge that can be used in the creation and refinement of a design.  The research aims to identify and illustrate the potential role of GIS as a tool in landscape design research, so as to provide insight into the possibilities and limitations of using GIS in this capacity. The critical, information-oriented case of Stourhead landscape garden (Wiltshire, UK, an example of a designed landscape that covers the scope and remit of landscape architecture design, forms the heart of the study. The exploration of Stourhead by means of GIS can be understood as a plausibility probe. Here the case study is considered a form of ‘quasi-experiment’, testing the hypothesis and generating a learning process that constitutes a prerequisite for advanced understanding, while using an adjusted version of the framework for landscape design analysis by Steenbergen and Reh (2003. This is a theoretically informed analytical method based on the formal interpretation of the landscape architectonic composition addressing four landscape architectonic categories: the basic, the spatial, the symbolic and the programmatic form. This study includes new aspects to be

  17. Distribution Network Design--literature study based

    OpenAIRE

    LI, ANG

    2012-01-01

    The focus of this research is companies' outbound distribution network design in supply chain management. Within the present competitive market, it is a fundamental importance for companies to achieve high level business performance with an effective supply chain. Outbound distribution network design as an important part in supply chain management, to a large extent decides whether companies can fulfill customers' requirement or not. Therefore, such a study is important for manufacturers and ...

  18. Video-based multimedia designs: A research study testing learning effectiveness

    Directory of Open Access Journals (Sweden)

    David Reiss

    2008-05-01

    Full Text Available This paper summarizes research conducted on three computer-based video models’ effectiveness for learning based on memory and comprehension. In this quantitative study, a two-minute video presentation was created and played back in three different types of media players, for a sample of eighty-seven college freshman. The three players evaluated include a standard QuickTime video/audio player, a QuickTime player with embedded triggers that launched HTML-based study guide pages, and a Macromedia Flash-based video/audio player with a text field, with user activated links to the study guides as well as other interactive on-line resources. An assumption guiding this study was that the enhanced designs presenting different types of related information would reinforce the material and produce better comprehension and retention. However, findings indicate that the standard video player was the most effective overall, which suggests that media designs able to control the focus of a learner’s attention to one specific stream of information, a single-stream focused approach, may be the most effective way to present media-based content. Résumé: Cet article résume une étude vérifiant l’efficacité de l’apprentissage basé sur la mémorisation et la compréhension, conduite à partir de trois modèles basés sur la vidéo informatisée. Dans cette étude quantitative, une vidéo de deux minutes a été créée et lue sur trois types de lecteurs différents, pour un échantillon de 87 étudiants universitaires de première année. Les trois lecteurs évalués comprenaient un lecteur standard audio/vidéo Quicktime, un lecteur Quicktime avec déclencheurs intégrés qui lançait un guide d’étude en HTML, et un lecteur audio/vidéo Flash Macromedia avec un champ texte, comprenant des liens activés par l’usager vers des guides d’étude et d’autres ressources interactives en ligne. Une supposition guidant cette étude était que les designs

  19. Applying Case-Based Method in Designing Self-Directed Online Instruction: A Formative Research Study

    Science.gov (United States)

    Luo, Heng; Koszalka, Tiffany A.; Arnone, Marilyn P.; Choi, Ikseon

    2018-01-01

    This study investigated the case-based method (CBM) instructional-design theory and its application in designing self-directed online instruction. The purpose of this study was to validate and refine the theory for a self-directed online instruction context. Guided by formative research methodology, this study first developed an online tutorial…

  20. Developing effective web-based regional anesthesia education: a randomized study evaluating case-based versus non-case-based module design.

    Science.gov (United States)

    Kopp, Sandra L; Smith, Hugh M

    2011-01-01

    Little is known about the use of Web-based education in regional anesthesia training. Benefits of Web-based education include the ability to standardize learning material quality and content, build appropriate learning progressions, use interactive multimedia technologies, and individualize delivery of course materials. The goals of this investigation were (1) to determine whether module design influences regional anesthesia knowledge acquisition, (2) to characterize learner preference patterns among anesthesia residents, and (3) to determine whether learner preferences play a role in knowledge acquisition. Direct comparison of knowledge assessments, learning styles, and learner preferences will be made between an interactive case-based and a traditional textbook-style module design. Forty-three Mayo Clinic anesthesiology residents completed 2 online modules, a knowledge pretest, posttest, an Index of Learning Styles assessment, and a participant satisfaction survey. Interscalene and lumbar plexus regional techniques were selected as the learning content for 4 Web modules constructed using the Blackboard Vista coursework application. One traditional textbook-style module and 1 interactive case-based module were designed for each of the interscalene and lumbar plexus techniques. Participants scored higher on the postmodule knowledge assessment for both of the interscalene and lumbar plexus modules. Postmodule knowledge performance scores were independent of both module design (interactive case-based versus traditional textbook style) and learning style preferences. However, nearly all participants reported a preference for Web-based learning and believe that it should be used in anesthesia resident education. Participants did not feel that Web-base learning should replace the current lecture-based curriculum. All residents scored higher on the postmodule knowledge assessment, but this improvement was independent of the module design and individual learning styles

  1. Model of Values-Based Management Process in Schools: A Mixed Design Study

    Science.gov (United States)

    Dogan, Soner

    2016-01-01

    The aim of this paper is to evaluate the school administrators' values-based management behaviours according to the teachers' perceptions and opinions and, accordingly, to build a model of values-based management process in schools. The study was conducted using explanatory design which is inclusive of both quantitative and qualitative methods.…

  2. Designing satisfaction studies

    DEFF Research Database (Denmark)

    Kristensen, Kai; Eskildsen, Jacob Kjær

    2007-01-01

    In the effect sampling method, presentation of researcher, the intro text, the order of questions in the questionnaire along with the number of categories in the rating scale is tested in relation to the design of satisfaction studies. Based on the analyses specific recommendations for designing...... satisfaction studies are given....

  3. Theoretical and numerical studies of TWR based on ESFR core design

    International Nuclear Information System (INIS)

    Zhang, Dalin; Chen, Xue-Nong; Flad, Michael; Rineiski, Andrei; Maschek, Werner

    2013-01-01

    Highlights: • The traveling wave reactor (TWR) is studied based on the core design of the European Sodium-cooled Fast Reactor (ESFR). • The conventional fuel shuffling technique is used to produce a continuous radial fuel movement. • A stationary self sustainable nuclear fission power can be established asymptotically by only loading natural or depleted uranium. • The multi-group deterministic neutronic code ERANOS is applied. - Abstract: This paper deals with the so-called traveling wave reactor (TWR) based on the core design of the European Sodium-cooled Fast Reactor (ESFR). The current concept of TWR is to use the conventional radial fuel shuffling technique to produce a continuous radial fuel movement so that a stationary self sustainable nuclear fission power can be established asymptotically by only loading fertile material consisting of natural or depleted uranium. The core design of ESFR loaded with metallic uranium fuel without considering the control mechanism is used as a practical application example. The theoretical studies focus mainly on qualitative feasibility analyses, i.e. to identify out in general essential parameter dependences of such a kind of reactor. The numerical studies are carried out more specifically on a certain core design. The multi-group deterministic neutronic code ERANOS with the JEFF3.1 data library is applied as a basic tool to perform the neutronics and burn-up calculations. The calculations are performed in a 2-D R-Z geometry, which is sufficient for the current core layout. Numerical results of radial fuel shuffling indicate that the asymptotic k eff parabolically varies with the shuffling period, while the burn-up increases linearly. Typical shuffling periods investigated in this study are in the range of 300–1000 days. The important parameters, e.g. k eff , the burn-up, the power peaking factor, and safety coefficients are calculated

  4. Research-based design & design-based research: Affordances, limitations and synergies

    NARCIS (Netherlands)

    McKenney, Susan

    2015-01-01

    Research-based design is an orientation to educational development that is explicitly informed by existing research as well as formative evaluation. Design-based research is a genre of inquiry in which the design of innovative solutions to problems in educational practice provides the context for

  5. Watershed-based survey designs

    Science.gov (United States)

    Detenbeck, N.E.; Cincotta, D.; Denver, J.M.; Greenlee, S.K.; Olsen, A.R.; Pitchford, A.M.

    2005-01-01

    Watershed-based sampling design and assessment tools help serve the multiple goals for water quality monitoring required under the Clean Water Act, including assessment of regional conditions to meet Section 305(b), identification of impaired water bodies or watersheds to meet Section 303(d), and development of empirical relationships between causes or sources of impairment and biological responses. Creation of GIS databases for hydrography, hydrologically corrected digital elevation models, and hydrologic derivatives such as watershed boundaries and upstream–downstream topology of subcatchments would provide a consistent seamless nationwide framework for these designs. The elements of a watershed-based sample framework can be represented either as a continuous infinite set defined by points along a linear stream network, or as a discrete set of watershed polygons. Watershed-based designs can be developed with existing probabilistic survey methods, including the use of unequal probability weighting, stratification, and two-stage frames for sampling. Case studies for monitoring of Atlantic Coastal Plain streams, West Virginia wadeable streams, and coastal Oregon streams illustrate three different approaches for selecting sites for watershed-based survey designs.

  6. Cognitive Activity-based Design Methodology for Novice Visual Communication Designers

    Science.gov (United States)

    Kim, Hyunjung; Lee, Hyunju

    2016-01-01

    The notion of design thinking is becoming more concrete nowadays, as design researchers and practitioners study the thinking processes involved in design and employ the concept of design thinking to foster better solutions to complex and ill-defined problems. The goal of the present research is to develop a cognitive activity-based design…

  7. ERGONOMIC DESIGN RECOMMENDATIONS BASED ON AN ACTUAL CHAINSAW DESIGN

    Directory of Open Access Journals (Sweden)

    J. Kaljun

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: To develop high quality products, a designer has to consider various influential factors, one of which is ergonomics. And to fashion a specific product for the user, a designer needs expert knowledge of the user’s requirements. However, expert knowledge can also be accessed through an intelligent advisory system for ergonomic design support. The effectiveness of such an expert system depends mainly on the quality of the knowledge base and on the appropriateness of the system's inference engine. Data for the system’s knowledge base can be collected in different ways. One approach is to study relevant projects to collect appropriate ergonomic solutions; another is to recognise bottlenecks in ergonomic design. This paper presents a case study of the design of an actual chainsaw – with emphasis on ergonomic design solutions – that can be transformed into ergonomic design recommendations. At the end of the paper, an application of one of the derived recommendations within the knowledge base of the intelligent advisory system is presented.

    AFRIKAANSE OPSOMMING: By die ontwerp van gehaltegoedere moet aandag gegee word aan verskeie faktore soos die Ergonomie. Die produkontwerper moet deeglike kennis dra van die verbruikersbehoeftes. Daarbenewens moet hy liefs ook gebruik maak van ’n intelligente sisteem vir ontwerphulp. Die navorsing is toegespits op datasteun vir ’n kettingsaagontwerp en toon hoe die intelligente sisteem betekenisvolle ondersteuning verleen.

  8. Quasi-experimental designs in practice-based research settings: design and implementation considerations.

    Science.gov (United States)

    Handley, Margaret A; Schillinger, Dean; Shiboski, Stephen

    2011-01-01

    Although randomized controlled trials are often a gold standard for determining intervention effects, in the area of practice-based research (PBR), there are many situations in which individual randomization is not possible. Alternative approaches to evaluating interventions have received increased attention, particularly those that can retain elements of randomization such that they can be considered "controlled" trials. Methodological design elements and practical implementation considerations for two quasi-experimental design approaches that have considerable promise in PBR settings--the stepped-wedge design, and a variant of this design, a wait-list cross-over design, are presented along with a case study from a recent PBR intervention for patients with diabetes. PBR-relevant design features include: creation of a cohort over time that collects control data but allows all participants (clusters or patients) to receive the intervention; staggered introduction of clusters; multiple data collection points; and one-way cross-over into the intervention arm. Practical considerations include: randomization versus stratification, training run in phases; and extended time period for overall study completion. Several design features of practice based research studies can be adapted to local circumstances yet retain elements to improve methodological rigor. Studies that utilize these methods, such as the stepped-wedge design and the wait-list cross-over design, can increase the evidence base for controlled studies conducted within the complex environment of PBR.

  9. A comparative study of teachers’ perceptions of design-based learning

    NARCIS (Netherlands)

    Gómez Puente, S.M.; Hattum-Janssen, van N.; Campos, de L.C.; Hattum-Janssen, van N.; Lima, R.M.; Carvalho, D.; Campos, de L.C.

    2012-01-01

    Design-based learning (DBL) is an instructional approach in which students gather and process theoretical knowledge while working in the design of artifacts, systems and innovative solutions in project settings. In the context of secondary education, DBL has been used as an educational form to teach

  10. Using a Design Science Perspective to Understand a Complex Design-Based Research Process

    DEFF Research Database (Denmark)

    Bækgaard, Lars

    2012-01-01

    The purpose of the paper is to demonstrate how a design science perspective can be used to describe and understand a set of related design-based research processes. We describe and analyze a case study in a manner that is inspired by design science. The case study involves the design of modeling......-based research processes. And we argue that a design science perspective may be useful for both researchers and practitioners....... tools and the redesign of an information service in a library. We use a set of guidelines from a design science perspective to organize the description and analysis of the case study. By doing this we demonstrate the usefulness of design science as an analytical tool for understanding related design...

  11. Integration of evidence-based and experience-based design: contributions from a study in a health care service

    Directory of Open Access Journals (Sweden)

    Mirela S. da Rosa

    2015-06-01

    Full Text Available The purpose this paper is to present an integrated study of Service Design and the Mechanism of the Production Function (MPF for redesigning the health care services to improve the perceived value of the patient and increase the productivity of hospital operations by eliminating wastes. The method used was action research and applied in an ICU of a private hospital in southern Brazil. The techniques of participant observation, interviews, archival research and meetings co-creation with a team of the hospital were used to collect data. Data were analyzed through content analysis of the interviews and the Design Service and Production Engineering tools. Evidence based approaches tends to contribute to the replication of the project outcomes in future cases. The MPF can support project development in the field of Design, as well the integrated approach developed in the healthcare sector, helped to devote more time to the phases of diagnosis and implementation. The findings are useful to demonstrate that can use simultaneously approaches the Service Design and MPF for the development of more robust solutions in health care environment. Further research could be done in other private or public hospitals as well as in other hospital units besides the ICUs. Limitations include the work done in a single hospital and service unit, data collected from a small group of people in the hospital. Integrating Evidence-Based Design, Experience-Based Design and the MPF can produce a more robust way to justify and define the focus of improvements in health care services.

  12. Study on concept of web-based reactor piping design data platform

    International Nuclear Information System (INIS)

    Wang Yu; Zhou Yu; Dong Jianling; Meng Yang

    2005-01-01

    For solving the piping design problems such as design data deficiency, designer communication inconvenience and design project inconsistence, Reactor Piping Design Database Platform, which is the main part of the Integrated Nuclear Project Research Platform, is proposed by analyzing the nuclear piping designs in detail. The functions and system structures of the platform are described in the paper for the sake of the realization of the Reactor Piping Design Database Platform. The platform is constituted by web-based management interface, AutoPlant selected as CAD software, and relation database management system (DBMS). (authors)

  13. Design-Based Research

    DEFF Research Database (Denmark)

    Gynther, Karsten; Christensen, Ove; Petersen, Trine Brun

    2012-01-01

    I denne artikel introduceres Design Based Research for første gang på dansk i et videnskabeligt tidsskrift. Artiklen præsenterer de grundlæggende antagelser, som ligger til grund for Design Based Research-traditionen, og artiklen diskuterer de principper, som ligger til grund for gennemførelse af...... et DBR-forskningsprojekt. Med udgangspunkt i forsknings- og udviklingsprojektet ELYK: E-læring, Yderområder og Klyngedannelse, præsenteres den innovationsmodel, som projektet har udviklet med udgangspunkt i Design Based Research traditionen. ELYKs DBR innovationsmodel har vist sig effektiv i forhold...

  14. Multi performance option in direct displacement based design

    Directory of Open Access Journals (Sweden)

    Muljati Ima

    2017-01-01

    Full Text Available Compare to traditional method, direct displacement based design (DDBD offers the more rational design choice due to its compatibility with performance based design which is controlled by the targeted displacement in design. The objectives of this study are: 1 to explore the performance of DDBD for design Level-1, -2 and -3; 2 to determine the most appropriate design level based on material efficiency and damage risk; and 3 to verify the chosen design in order to check its performance under small-, moderate- and severe earthquake. As case study, it uses regular concrete frame structures consists of fourand eight-story with typical plan, located in low- and high-risk seismicity area. The study shows that design Level-2 (repairable damage is the most appropriate choice. Nonlinear time history analysis is run for each case study in order to verify their performance based on parameter: story drift, damage indices, and plastic mechanism. It can be concluded that DDBD performed very well in predicting seismic demand of the observed structures. Design Level-2 can be chosen as the most appropriate design level. Structures are in safe plastic mechanism under all level of seismicity although some plastic hinges formed at some unexpected locations.

  15. Interactive Multimedia-Based Animation: A Study of Effectiveness on Fashion Design Technology Learning

    Science.gov (United States)

    Wiana, W.

    2018-01-01

    The learning process is believed will reach optimal results if facilitated by diversity of learning’s device from aspects of the approach, method, media or it’s evaluation system, in individually, groups, or as well as classical. One of the learning’s Device can be developed in an attempt to improve the results of the study is Computer Based Learning (CBL). CBL was developed aim to help students to understand the concepts of the learning material which presented interactively by the system and able to provide information and learning process better. This research is closely related to efforts to improve the quality of Fashion design in digital format learning, with specific targets to generate interactive multimedia-based animation as effective media and learning resources for fashion design learning. Applications that are generated may be an option for delivering learning material as well as to engender interest in learning as well as understanding with students against the subject matter so that it can improve the learning achievements of students. The instruments used to collect data is a test sheet of mastering the concept which developed on the basis of indicators understanding the concept of fashion design, the material elements and principles of fashion design as well as application on making fashion design. As for the skills test is done through test performance to making fashion design in digital format. The results of testing against the mastery of concepts and skills of fashion designing in digital formatted shows that experimental group obtained significantly higher qualifications compared to the control group. That means that the use of interactive multimedia-based animation, effective to increased mastery of concepts and skills on making fashion design in digital format.

  16. Artistic and Engineering Design of Platform-Based Production Systems: A Study of Swedish Architectural Practice

    Directory of Open Access Journals (Sweden)

    Gustav Jansson

    2018-02-01

    Full Text Available Research on platform-based production systems for house-building has focused on production and manufacturing issues. The aim of this research is to explore how the architectural design process contributes to the industrialised house-building industry from the perspective of creative design work. It also aims to describe how constraints affect architectural design work in the engineer-to-order context, when using platform-based production systems. Architects with experience in using platform-based building systems with different degrees of constraints were interviewed regarding creative aspects of the design work. The interviews, together with documents relating to platform constraints, were then analysed from the perspective of artistic and engineering design theories. The results show the benefits and issues of using platform constraints, both with prefabrication of volumetric modules, as well as prefabricated slab and wall elements. The study highlights a major research gap by describing how architectural work, from both the creative artistic and engineering design perspectives, is affected by constraints in the building platform: (1 the architectural design work goes through a series of divergent and convergent processes where the divergent processes are explorative and the convergent processes are solution-oriented; and (2, there is a trade-off between creativity and efficiency in the design work. Open parameters for layout design are key to architectural creativity, while predefinition supports efficiency. The results also provide an understanding of the potential for creativity in artistic and engineering work tasks through different phases in design, and how they are related to constraints in the platform. The main limitation of the research is the number of interviewed architects who had different background experiences of working with different types of platform constraints. More studies are needed to confirm the observations and to

  17. Variations in enamel damage after debonding of two different bracket base designs: An in vitro study.

    Science.gov (United States)

    Ahangar Atashi, Mohammad Hossein; Sadr Haghighi, Amir Hooman; Nastarin, Parastou; Ahangar Atashi, Sina

    2018-01-01

    Background. Bracket base design is a factor influencing shear bond strength. High shear bond strength leads to enamel crack formation during debonding. The aim of this study was to compare enamel damage variations, including the number and length of enamel cracks after debonding of two different base designs. Methods. Eighty-eight extracted human premolars were randomly divided into2 groups (n=44). The teeth in each group were bonded by two types of brackets with different base designs: 80-gauge mesh design versus anchor pylon design with pylons for adhesive retention. The number and length of enamel cracks before bonding and after debonding were evaluated under an optical stereomicroscope ×40 in both groups. Mann-Whitney U test was used to compare the number of cracks between the two groups. ANCOVA was used for comparison of crack lengths after and before debonding in each group and between the two groups. Results. There was a significant increase in enamel crack length and numbers in each group after debonding. There was no significant difference in enamel crack numbers after debonding between the two groups, whereas the length of enamel cracks was significantly greater in anchor pylon base design after debonding. Conclusion. Bracket bases with pylon design for adhesive retention caused more iatrogenic debonding damage to enamel surface.

  18. A SAS-based solution to evaluate study design efficiency of phase I pediatric oncology trials via discrete event simulation.

    Science.gov (United States)

    Barrett, Jeffrey S; Jayaraman, Bhuvana; Patel, Dimple; Skolnik, Jeffrey M

    2008-06-01

    Previous exploration of oncology study design efficiency has focused on Markov processes alone (probability-based events) without consideration for time dependencies. Barriers to study completion include time delays associated with patient accrual, inevaluability (IE), time to dose limiting toxicities (DLT) and administrative and review time. Discrete event simulation (DES) can incorporate probability-based assignment of DLT and IE frequency, correlated with cohort in the case of DLT, with time-based events defined by stochastic relationships. A SAS-based solution to examine study efficiency metrics and evaluate design modifications that would improve study efficiency is presented. Virtual patients are simulated with attributes defined from prior distributions of relevant patient characteristics. Study population datasets are read into SAS macros which select patients and enroll them into a study based on the specific design criteria if the study is open to enrollment. Waiting times, arrival times and time to study events are also sampled from prior distributions; post-processing of study simulations is provided within the decision macros and compared across designs in a separate post-processing algorithm. This solution is examined via comparison of the standard 3+3 decision rule relative to the "rolling 6" design, a newly proposed enrollment strategy for the phase I pediatric oncology setting.

  19. Professional development for design-based learning in engineering education: a case study

    Science.gov (United States)

    Gómez Puente, Sonia M.; van Eijck, Michiel; Jochems, Wim

    2015-01-01

    Design-based learning (DBL) is an educational approach in which students gather and apply theoretical knowledge to solve design problems. In this study, we examined how critical DBL dimensions (project characteristics, design elements, the teacher's role, assessment, and social context) are applied by teachers in the redesign of DBL projects. We conducted an intervention for the professional development of the DBL teachers in the Mechanical Engineering and the Electrical Engineering departments. We used the Experiential Learning Cycle as an educational model for the professionalisation programme. The findings show that the programme encouraged teachers to apply the DBL theoretical framework. However, there are some limitations with regard to specific project characteristics. Further research into supporting teachers to develop open-ended and multidisciplinary activities in the projects that support learning is recommended.

  20. Designing Health Websites Based on Users’ Web-Based Information-Seeking Behaviors: A Mixed-Method Observational Study

    Science.gov (United States)

    Pang, Patrick Cheong-Iao; Verspoor, Karin; Pearce, Jon

    2016-01-01

    Background Laypeople increasingly use the Internet as a source of health information, but finding and discovering the right information remains problematic. These issues are partially due to the mismatch between the design of consumer health websites and the needs of health information seekers, particularly the lack of support for “exploring” health information. Objective The aim of this research was to create a design for consumer health websites by supporting different health information–seeking behaviors. We created a website called Better Health Explorer with the new design. Through the evaluation of this new design, we derive design implications for future implementations. Methods Better Health Explorer was designed using a user-centered approach. The design was implemented and assessed through a laboratory-based observational study. Participants tried to use Better Health Explorer and another live health website. Both websites contained the same content. A mixed-method approach was adopted to analyze multiple types of data collected in the experiment, including screen recordings, activity logs, Web browsing histories, and audiotaped interviews. Results Overall, 31 participants took part in the observational study. Our new design showed a positive result for improving the experience of health information seeking, by providing a wide range of information and an engaging environment. The results showed better knowledge acquisition, a higher number of page reads, and more query reformulations in both focused and exploratory search tasks. In addition, participants spent more time to discover health information with our design in exploratory search tasks, indicating higher engagement with the website. Finally, we identify 4 design considerations for designing consumer health websites and health information–seeking apps: (1) providing a dynamic information scope; (2) supporting serendipity; (3) considering trust implications; and (4) enhancing interactivity

  1. Designing Health Websites Based on Users' Web-Based Information-Seeking Behaviors: A Mixed-Method Observational Study.

    Science.gov (United States)

    Pang, Patrick Cheong-Iao; Chang, Shanton; Verspoor, Karin; Pearce, Jon

    2016-06-06

    Laypeople increasingly use the Internet as a source of health information, but finding and discovering the right information remains problematic. These issues are partially due to the mismatch between the design of consumer health websites and the needs of health information seekers, particularly the lack of support for "exploring" health information. The aim of this research was to create a design for consumer health websites by supporting different health information-seeking behaviors. We created a website called Better Health Explorer with the new design. Through the evaluation of this new design, we derive design implications for future implementations. Better Health Explorer was designed using a user-centered approach. The design was implemented and assessed through a laboratory-based observational study. Participants tried to use Better Health Explorer and another live health website. Both websites contained the same content. A mixed-method approach was adopted to analyze multiple types of data collected in the experiment, including screen recordings, activity logs, Web browsing histories, and audiotaped interviews. Overall, 31 participants took part in the observational study. Our new design showed a positive result for improving the experience of health information seeking, by providing a wide range of information and an engaging environment. The results showed better knowledge acquisition, a higher number of page reads, and more query reformulations in both focused and exploratory search tasks. In addition, participants spent more time to discover health information with our design in exploratory search tasks, indicating higher engagement with the website. Finally, we identify 4 design considerations for designing consumer health websites and health information-seeking apps: (1) providing a dynamic information scope; (2) supporting serendipity; (3) considering trust implications; and (4) enhancing interactivity. Better Health Explorer provides strong

  2. Implementation of an Industrial-Based Case Study as the Basis for a Design Project in an Introduction to Mechanical Design Course

    Science.gov (United States)

    Lackey, Ellen

    2011-01-01

    The purpose of this paper is to discuss the implementation of an industrial-based case study as the basis for a design project for the Spring 2009 Introduction to Mechanical Design Course at the University of Mississippi. Course surveys documented the lack of student exposure in classes to the types of projects typically experienced by engineers…

  3. Design for game based learning platforms

    DEFF Research Database (Denmark)

    Sørensen, Birgitte Holm; Meyer, Bente

    2010-01-01

    This paper focuses on the challenges related to the design of game based learning platforms for formal learning contexts that are inspired by the pupil's leisure time related use of web 2.0. The paper is based on the project Serious Games on a Global Market Place (2007-2011) founded by the Danish...... of web 2.0 and integrates theories of learning, didactics, games, play, communication, multimodality and different pedagogical approaches. In relation to the introduced model the teacher role is discussed.......This paper focuses on the challenges related to the design of game based learning platforms for formal learning contexts that are inspired by the pupil's leisure time related use of web 2.0. The paper is based on the project Serious Games on a Global Market Place (2007-2011) founded by the Danish...... Council for Strategic Research, in which an online game-based platform for English as a foreign language in primary school is studied. The paper presents a model for designing for game based learning platforms. This design is based on cultural and ethnographic based research on children's leisure time use...

  4. Using a Design-Based Research Study to Identify Principles for Training Instructors to Teach Online

    Science.gov (United States)

    Shattuck, Julie; Anderson, Terry

    2013-01-01

    Within the overall framework of design-based research, this paper reports on a study that focused on evaluating an online training course for online instructors. This intervention was designed as a possible solution to the problem facing some higher education institutions of how to provide quality, accessible training for mostly part-time…

  5. Emergency Response Program Designing Based On Case Study ERP Regulations In Ilam Gas Refinery

    Directory of Open Access Journals (Sweden)

    Mehdi Tahmasbi

    2015-08-01

    Full Text Available The study of Emergency response plan designing is one of the most important prevention approaches in crisis management. This study aims to design emergency response plan based on case study ERP regulations in Ilam gas refinery. On the basis of risk assessment and identification techniques such as HAZOP and FMEA in Ilam gas refinery the risks have been prioritized and then according to this prioritization the design of possible scenarios which have the highest rate of occurrence and the highest level of damage has been separated. Possible scenarios were simulated with PHAST software. Then emergency response program has been designed for the special mode or similar cases. According to the internal emergency response plan for Ilam gas refinery and predictable conditions of the process special instructions should be considered at the time of the incident to suffer the least damage on people and environment in the shortest time possible.

  6. Case Study of a Project-Based Learning Course in Civil Engineering Design

    Science.gov (United States)

    Gavin, K.

    2011-01-01

    This paper describes the use of project-based learning to teach design skills to civil engineering students at University College Dublin (UCD). The paper first considers the development of problem-based leaning (PBL) as a tool in higher education. The general issues to be considered in the design of the curriculum for a PBL module are reviewed.…

  7. Study on design procedure of three-dimensional building base isolation system using thick rubber bearing

    International Nuclear Information System (INIS)

    Yabana, Shuichi; Matsuda, Akihiro

    2003-01-01

    In this study, design procedure on three-dimensional base isolation system is developed. Base isolation system proposed by CRIEPI uses thick rubber bearing and damper as isolation device. As for thick rubber bearings, design formula for evaluating vertical stiffness is proposed, and design conditions regarding size and vertical pressure are investigated. Figure-U type lead damper is proposed as three-dimensional damper and by loading tests its mechanical characteristics is evaluated. The concept of multi-layered interconnected rubber bearing, which is advantageous over large scale bearing in manufacturability, is proposed and its good performance is confirmed by the loading test. Through the response analyses, it is shown the rocking response of the proposed three-dimensional base isolation system is very small and not influential to the system, and the reduction of the vertical response is attained using the proposed isolation device. (author)

  8. Model-Based Requirements Management in Gear Systems Design Based On Graph-Based Design Languages

    Directory of Open Access Journals (Sweden)

    Kevin Holder

    2017-10-01

    Full Text Available For several decades, a wide-spread consensus concerning the enormous importance of an in-depth clarification of the specifications of a product has been observed. A weak clarification of specifications is repeatedly listed as a main cause for the failure of product development projects. Requirements, which can be defined as the purpose, goals, constraints, and criteria associated with a product development project, play a central role in the clarification of specifications. The collection of activities which ensure that requirements are identified, documented, maintained, communicated, and traced throughout the life cycle of a system, product, or service can be referred to as “requirements engineering”. These activities can be supported by a collection and combination of strategies, methods, and tools which are appropriate for the clarification of specifications. Numerous publications describe the strategy and the components of requirements management. Furthermore, recent research investigates its industrial application. Simultaneously, promising developments of graph-based design languages for a holistic digital representation of the product life cycle are presented. Current developments realize graph-based languages by the diagrams of the Unified Modelling Language (UML, and allow the automatic generation and evaluation of multiple product variants. The research presented in this paper seeks to present a method in order to combine the advantages of a conscious requirements management process and graph-based design languages. Consequently, the main objective of this paper is the investigation of a model-based integration of requirements in a product development process by means of graph-based design languages. The research method is based on an in-depth analysis of an exemplary industrial product development, a gear system for so-called “Electrical Multiple Units” (EMU. Important requirements were abstracted from a gear system

  9. Study of New Materials Design based on Hadoop

    Directory of Open Access Journals (Sweden)

    Wu Jun

    2016-01-01

    Full Text Available With the rapid development of information technology, the scientific research shows that the data mining and other information technology could be used in the design of new materials. It is explicit that Intelligent Materials research focuses on using physical and chemical principles combined with computer techniques such as Big Data, Cloud computing and Intelligent modeling and simulation to solve chemical problems. In this paper, based on the cluster based outlier algorithm as the main body, this paper discusses the definition New Materials research In the Hadoop cloud platform, and the parallel processing of Map-Reduce model. The performance this model of new material was established by using the method of Map-Reduction provided the basis for the performance optimization.

  10. Accelerator-based conversion (ABC) of weapons plutonium: Plant layout study and related design issues

    International Nuclear Information System (INIS)

    Cowell, B.S.; Fontana, M.H.; Krakowski, R.A.; Beard, C.A.; Buksa, J.J.; Davidson, J.W.; Sailor, W.C.; Williamson, M.A.

    1995-01-01

    In preparation for and in support of a detailed R and D Plan for the Accelerator-Based Conversion (ABC) of weapons plutonium, an ABC Plant Layout Study was conducted at the level of a pre-conceptual engineering design. The plant layout is based on an adaptation of the Molten-Salt Breeder Reactor (MSBR) detailed conceptual design that was completed in the early 1070s. Although the ABC Plant Layout Study included the Accelerator Equipment as an essential element, the engineering assessment focused primarily on the Target; Primary System (blanket and all systems containing plutonium-bearing fuel salt); the Heat-Removal System (secondary-coolant-salt and supercritical-steam systems); Chemical Processing; Operation and Maintenance; Containment and Safety; and Instrumentation and Control systems. Although constrained primarily to a reflection of an accelerator-driven (subcritical) variant of MSBR system, unique features and added flexibilities of the ABC suggest improved or alternative approaches to each of the above-listed subsystems; these, along with the key technical issues in need of resolution through a detailed R ampersand D plan for ABC are described on the bases of the ''strawman'' or ''point-of-departure'' plant layout that resulted from this study

  11. FEM BASED PARAMETRIC DESIGN STUDY OF TIRE PROFILE USING DEDICATED CAD MODEL AND TRANSLATION CODE

    Directory of Open Access Journals (Sweden)

    Nikola Korunović

    2014-12-01

    Full Text Available In this paper a finite element method (FEM based parametric design study of the tire profile shape and belt width is presented. One of the main obstacles that similar studies have faced is how to change the finite element mesh after a modification of the tire geometry is performed. In order to overcome this problem, a new approach is proposed. It implies automatic update of the finite elements mesh, which follows the change of geometric design parameters on a dedicated CAD model. The mesh update is facilitated by an originally developed mapping and translation code. In this way, the performance of a large number of geometrically different tire design variations may be analyzed in a very short time. Although a pilot one, the presented study has also led to the improvement of the existing tire design.

  12. Reflections on Design-Based Research

    DEFF Research Database (Denmark)

    Ørngreen, Rikke

    2015-01-01

    Design-Based Research is an intervention method that researches educational design (products or processes) in real-life settings with the dual purpose of generating theories about the domain and develop the design iteratively. This paper is an integrative review with a personal ethnographic...... narrative that draws on Design-Based Research literature, and identifies and discusses elements from Interaction Design and Action Research that the Design-Based Research approach could apply, situating the research in online educational projects, where participants are distributed in time and space...

  13. Design of PREVENCION: a population-based study of cardiovascular disease in Peru.

    Science.gov (United States)

    Medina-Lezama, Josefina; Chirinos, Julio A; Zea Díaz, Humberto; Morey, Oscar; Bolanos, Juan F; Munoz-Atahualpa, Edgar; Chirinos-Pacheco, Julio

    2005-11-02

    Latin America is undergoing the epidemiologic transition that occurred earlier in developed countries, and is likely to face a gigantic epidemic of heart disease in the next few years unless urgent action is taken. The first essential component of any effective cardiovascular disease (CVD) control program is to establish reliable estimates of cardiovascular disease-related morbidity and mortality. However, such data from population-based studies in Latin America are still lacking. In this paper, we present the design and operation of PREVENCION (Estudio Peruano de Prevalencia de Enfermedades Cardiovasculares, for Peruvian Study of the Prevalence of Cardiovascular diseases). PREVENCION is an ongoing population-based study on a representative sample of the civilian non-institutionalized population of the second largest city in Peru. Its population is comparable to the rest of the Peruvian urban population and closely resembles other Latin American populations in countries such as Bolivia and Ecuador. Our study will contribute to the enormous task of understanding and preventing CVD in Latin America.

  14. Move the Neighborhood: study design of a community-based participatory public open space intervention

    DEFF Research Database (Denmark)

    Pawlowski, Charlotte Skau; Winge, Laura; Carroll, Sidse

    evaluation will be used to gain knowledge of the intervention processes. DISCUSSION: The study presents new methods and approaches in the field of public open space interventions through interdisciplinary collaboration, participatory co-design approach and combination of measurements. Using both effect......BACKGROUND: A limited amount of research has examined the effect of changing public open spaces on active living. This abstract presents the study protocol of an intervention study designed in an interdisciplinary collaboration built on principles of Community-Based Participatory Research (CBPR...... and process evaluations the study will provide unique insights in the role and importance of the interdisciplinary collaboration, participatory processes, tailoring changes in public open space to local needs and wishes. These results can be used to guide urban renewal projects in deprived neighbourhoods...

  15. [Observational studies in the era of evidence based medicine: short review on their relevance, taxonomy and designs].

    Science.gov (United States)

    Fronteira, Ines

    2013-01-01

    In this review of the literature, we distinguish between experimental and observational studies, highlighting the importance that the later have gained in the era of evidence-based medicine. We further analyze the value of observational studies in light of experimental studies. We present a taxonomy for observational studies based on units of observation and measurement (cross-sectional or longitudinal). We distinguish between descriptive studies and analytical studies. Then, and given its specificity, we define and present a classification for ecological studies. We define and consider the advantages and disadvantages of cross-sectional, case control and cohort studies. We analyze the strength of the evidence given by each study design. We finished by examining what should guide the choice of a study design.

  16. Adopting an Evidence-Based Lifestyle Physical Activity Program: Dissemination Study Design and Methods.

    Science.gov (United States)

    Dunn, Andrea L; Buller, David B; Dearing, James W; Cutter, Gary; Guerra, Michele; Wilcox, Sara; Bettinghaus, Erwin P

    2012-06-01

    BACKGROUND: There is a scarcity of research studies that have examined academic-commercial partnerships to disseminate evidence-based physical activity programs. Understanding this approach to dissemination is essential because academic-commercial partnerships are increasingly common. Private companies have used dissemination channels and strategies to a degree that academicians have not, and declining resources require academicians to explore these partnerships. PURPOSE: This paper describes a retrospective case-control study design including the methods, demographics, organizational decision-making, implementation rates, and marketing strategy for Active Living Every Day (ALED), an evidence-based lifestyle physical activity program that has been commercially available since 2001. Evidence-based public health promotion programs rely on organizations and targeted sectors to disseminate these programs although relatively little is known about organizational-level and sector-level influences that lead to their adoption and implementation. METHODS: Cases (n=154) were eligible if they had signed an ALED license agreement with Human Kinetics (HK), publisher of the program's textbooks and facilitator manuals, between 2001 and 2008. Two types of controls were matched (2:2:1) and stratified by sector and region. Active controls (Control 1; n=319) were organizations that contacted HK to consider adopting ALED. Passive controls (Control 2; n=328) were organizations that received unsolicited marketing materials and did not initiate contact with HK. We used Diffusion of Innovations Theory (DIT) constructs as the basis for developing the survey of cases and controls. RESULTS: Using the multi-method strategy recommended by Dillman, a total of n=801 cases and controls were surveyed. Most organizations were from the fitness sector followed by medical, nongovernmental, governmental, educational, worksite and other sectors with significantly higher response rates from government

  17. Collective design in 3D printing: A large scale empirical study of designs, designers and evolution

    DEFF Research Database (Denmark)

    Özkil, Ali Gürcan

    2017-01-01

    This paper provides an empirical study of a collective design platform (Thingiverse); with the aim of understanding the phenomenon and investigating how designs concurrently evolve through the large and complex network of designers. The case study is based on the meta-data collected from 158 489 ...

  18. Learning Design of Problem Based Learning Model Based on Recommendations of Sintax Study and Contents Issues on Physics Impulse Materials with Experimental Activities

    Directory of Open Access Journals (Sweden)

    Kristia Agustina

    2017-08-01

    Full Text Available This study aims to design learning Problem Based Learning Model based on syntax study recommendations and content issues on Physics Impulse materials through experiments. This research is a development research with Kemp model. The reference for making the learning design is the result of the syntax study and the content of existing PBL implementation problems from Agustina research. This instructional design is applied to the physics material about Impulse done through experimental activity. Limited trials were conducted on the SWCU Physics Education Study Program students group Salatiga, while the validity test was conducted by high school teachers and physics education lecturers. The results of the trial evaluation are limited and the validity test is used to improve the designs that have been made. The conclusion of this research is the design of learning by using PBL model on Impuls material by referring the result of syntax study and the problem content of existing PBL implementation can be produced by learning activity designed in laboratory experiment activity. The actual problem for Impuls material can be used car crash test video at factory. The results of validation tests and limited trials conducted by researchers assessed that the design of learning made by researchers can be used with small revisions. Suggestions from this research are in making learning design by using PBL model to get actual problem can by collecting news that come from newspaper, YouTube, internet, and television.

  19. Effectiveness of Facebook Based Learning to Enhance Creativity among Islamic Studies Students by Employing Isman Instructional Design Model

    Science.gov (United States)

    Alias, Norlidah; Siraj, Saedah; Daud, Mohd Khairul Azman Md; Hussin, Zaharah

    2013-01-01

    The study examines the effectiveness of Facebook based learning to enhance creativity among Islamic Studies students in the secondary educational setting in Malaysia. It describes the design process by employing the Isman Instructional Design Model. A quantitative study was carried out using experimental method and background survey. The…

  20. Sense of Community in a Blended Technology Integration Course: A Design-Based Research Study

    Science.gov (United States)

    Harrison, J. Buckley; West, Richard E.

    2014-01-01

    This design-based research study explored whether "sense of community" was maintained while flexibility in the course was increased through an adoption of a unique blended learning model. Data collected in this study show a significant drop in the sense of connectedness score from a mean of 50.8 out of 66 to a mean of 39.68 in the first…

  1. Urban Environment Development based on Universal Design Principles

    Science.gov (United States)

    Harsritanto, Bangun Ir

    2018-02-01

    Universal Design is a design which facilitated full range of human diversity. By applying Universal design principles, urban environment can be more functional and more user-friendly for everyone. This study examined five urban streets of South Korea as a country experienced on developing various urban street designs based on universal design. This study aimed to examine and compare the South Korea cases using seven principles of universal design. The research methods of this study are literature study, case study, and site observation. The results of this study are: South Korea cases are good practices, urgency of implementing the direction into local regulations; and change of urban development paradigm.

  2. Displacement Based Seismic Design Criteria

    International Nuclear Information System (INIS)

    Costello, J.F.; Hofmayer, C.; Park, Y.J.

    1999-01-01

    The USNRC has initiated a project to determine if any of the likely revisions to traditional earthquake engineering practice are relevant to seismic design of the specialized structures, systems and components of nuclear power plants and of such significance to suggest that a change in design practice might be warranted. As part of the initial phase of this study, a literature survey was conducted on the recent changes in seismic design codes/standards, on-going activities of code-writing organizations/communities, and published documents on displacement-based design methods. This paper provides a summary of recent changes in building codes and on-going activities for future codes. It also discusses some technical issues for further consideration

  3. Embracing model-based designs for dose-finding trials.

    Science.gov (United States)

    Love, Sharon B; Brown, Sarah; Weir, Christopher J; Harbron, Chris; Yap, Christina; Gaschler-Markefski, Birgit; Matcham, James; Caffrey, Louise; McKevitt, Christopher; Clive, Sally; Craddock, Charlie; Spicer, James; Cornelius, Victoria

    2017-07-25

    Dose-finding trials are essential to drug development as they establish recommended doses for later-phase testing. We aim to motivate wider use of model-based designs for dose finding, such as the continual reassessment method (CRM). We carried out a literature review of dose-finding designs and conducted a survey to identify perceived barriers to their implementation. We describe the benefits of model-based designs (flexibility, superior operating characteristics, extended scope), their current uptake, and existing resources. The most prominent barriers to implementation of a model-based design were lack of suitable training, chief investigators' preference for algorithm-based designs (e.g., 3+3), and limited resources for study design before funding. We use a real-world example to illustrate how these barriers can be overcome. There is overwhelming evidence for the benefits of CRM. Many leading pharmaceutical companies routinely implement model-based designs. Our analysis identified barriers for academic statisticians and clinical academics in mirroring the progress industry has made in trial design. Unified support from funders, regulators, and journal editors could result in more accurate doses for later-phase testing, and increase the efficiency and success of clinical drug development. We give recommendations for increasing the uptake of model-based designs for dose-finding trials in academia.

  4. A study on conceptual design of tritium production fusion reactor based on spherical torus

    International Nuclear Information System (INIS)

    He Kaihui; Huang Jinhua

    2003-01-01

    Conceptual design of an advanced tritium production reactor based on spherical torus (ST), which is an intermediate application of fusion energy, is presented. Different from traditional Tokamak tritium production reactor design, advanced plasma physics performance and compact structural characteristics of ST are used to minimize tritium leakage and to maximize tritium breeding ratio with arrangement of tritium production blankets as possible as it can do within vacuum vessel in order to produce certain amount of excess tritium except self-sufficient plasma core, corresponding plant availability 40% or more. Based on 2D neutronics calculation, preliminary conceptual design of ST-TPR is presented. Based on systematical analysis, design risk, uncertainty and backup are introduced generally for the backgrounds of next detailed conceptual design. (authors)

  5. Shear Bond Strength of Ceramic Brackets with Different Base Designs: Comparative In-vitro Study

    Science.gov (United States)

    Ansari, Mohd. Younus; Agarwal, Deepak K; Bhattacharya, Preeti; Ansar, Juhi; Bhandari, Ravi

    2016-01-01

    Introduction Knowledge about the Shear Bond Strength (SBS) of ceramic brackets with different base design is essential as it affects bond strength to enamel. Aim The aim of the present study was to evaluate and compare the effect of base designs of different ceramic brackets on SBS, and to determine the fracture site after debonding. Materials and Methods Four groups of ceramic brackets and one group of metal brackets with different base designs were used. Adhesive precoated base of Clarity Advanced (APC Flash-free) (Unitek/3M, Monrovia, California), microcrystalline base of Clarity Advanced (Unitek/3M, Monrovia, California), polymer mesh base of InVu (TP Orthodontics, Inc., La Porte, IN, United States), patented bead ball base of Inspire Ice (Ormco, Glendora, California), and a mechanical mesh base of Gemini Metal bracket (Unitek/3M, Monrovia, California). Ten brackets of each type were bonded to 50 maxillary premolars with Transbond XT (Unitek/3M). Samples were stored in distilled water at room temperature for 24 hours and subsequently tested in shear mode on a universal testing machine (Model 3382; Instron Corp., Canton, Massachusetts, USA) at a cross head speed of 1mm/minute with the help of a chisel. The debonded interface was recorded and analyzed to determine the predominant bond failure site under an optical microscope (Stereomicroscope) at 10X magnification. One way analysis of variance (ANOVA) was used to compare SBS. Tukey’s significant differences tests were used for post-hoc comparisons. The Adhesive Remnant Index (ARI) scores were compared by chi-square test. Results Mean SBS of microcrystalline base (27.26±1.73), was the highest followed by bead ball base (23.45±5.09), adhesive precoated base (20.13±5.20), polymer mesh base (17.54±1.91), and mechanical mesh base (17.50±2.41) the least. Comparing the frequency (%) of ARI Score among the groups, chi-square test showed significantly different ARI scores among the groups (χ2 = 34.07, pbrackets

  6. Design of a population-based study of visual impairment in India : The Andhra Pradesh eye disease study

    Directory of Open Access Journals (Sweden)

    Dandona Rakhi

    1997-01-01

    Full Text Available Reliable population-based epidemiologic data regarding vision and ocular morbidity, as well as those about the perceptions of people regarding visual impairment and eye care, are lacking for the most part in the developing world including India. These data are the basis on which effective eye care services can be developed. To meet this need we designed the Andhra Pradesh Eye Disease Study, a population-based epidemiology study of 10,000 people in the Indian state of Andhra Pradesh. The design of this study is described in this paper. Various options for the sample size, study areas, sampling procedure, and recruitment of subjects were considered. A sample size of 10,000 people, 5,000 each in the < or = 30 and > 30 years age groups, was determined to obtain reasonable confidence in estimating the prevalence of diseases and odds ratios for risk factors of interest. A multistage sampling strategy was chosen for the study which was assumed to give a design effect of 1.5 for the estimates. One urban area, Hyderabad, and three rural areas, West Godavari, Adilabad and Mahbubnagar districts, were selected in Andhra Pradesh. Interview instruments were developed to obtain detailed information about demographic data, diet, ocular and systemic history, risk factors for eye diseases, visual function, quality of life, barriers to eye care, and knowledge about eye diseases. A detailed examination procedure was devised to obtain a broad range of normative and abnormal data related to eyes and vision. A protocol was developed for doing automated visual fields, slitlamp and fundus photography. Computer databases were made in FoxPro for data entry and subsequent analysis with SPSS. Pilot studies were done to test the instruments, procedures, and logistics of the study in urban and rural areas. Information from the Andhra Pradesh Eye Disease Study is expected to help in planning and implementation of effective long-term preventive, curative, and

  7. Case-based Agile Fixture Design

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In order to realize the agility of the fixture design, such asreconfigurability, rescalability and reusability, fixture structure is function unit-based decomposed from a fire-new point of view. Which makes it easy for agile fixture to be reconfigured and modified. Thereby, the base of case-based agile fixture design system info is established.Whole case-based agile fixture design model is presented. In which, three modules are added relative to the other models, including case matching of fixture planning module, conflict arbitration module and agile fixture case modify module. The three modules could solve the previous problem that the experience and result are difficult to be reused in the process of design.Two key techniques in the process of the agile fixture design, the evaluation of case similarity, and restriction-based conflict arbitration, are listed. And some methods are presented to evaluate the similarity and clear up the conflict.

  8. A supportive architecture for CFD-based design optimisation

    Science.gov (United States)

    Li, Ni; Su, Zeya; Bi, Zhuming; Tian, Chao; Ren, Zhiming; Gong, Guanghong

    2014-03-01

    Multi-disciplinary design optimisation (MDO) is one of critical methodologies to the implementation of enterprise systems (ES). MDO requiring the analysis of fluid dynamics raises a special challenge due to its extremely intensive computation. The rapid development of computational fluid dynamic (CFD) technique has caused a rise of its applications in various fields. Especially for the exterior designs of vehicles, CFD has become one of the three main design tools comparable to analytical approaches and wind tunnel experiments. CFD-based design optimisation is an effective way to achieve the desired performance under the given constraints. However, due to the complexity of CFD, integrating with CFD analysis in an intelligent optimisation algorithm is not straightforward. It is a challenge to solve a CFD-based design problem, which is usually with high dimensions, and multiple objectives and constraints. It is desirable to have an integrated architecture for CFD-based design optimisation. However, our review on existing works has found that very few researchers have studied on the assistive tools to facilitate CFD-based design optimisation. In the paper, a multi-layer architecture and a general procedure are proposed to integrate different CFD toolsets with intelligent optimisation algorithms, parallel computing technique and other techniques for efficient computation. In the proposed architecture, the integration is performed either at the code level or data level to fully utilise the capabilities of different assistive tools. Two intelligent algorithms are developed and embedded with parallel computing. These algorithms, together with the supportive architecture, lay a solid foundation for various applications of CFD-based design optimisation. To illustrate the effectiveness of the proposed architecture and algorithms, the case studies on aerodynamic shape design of a hypersonic cruising vehicle are provided, and the result has shown that the proposed architecture

  9. Design Concepts for Muon-Based Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Ryne, R. D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Berg, J. S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Kirk, H. G. [Brookhaven National Lab. (BNL), Upton, NY (United States); Palmer, R. B. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stratkis, D. [Brookhaven National Lab. (BNL), Upton, NY (United States); Alexahin, Y. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Bross, A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Gollwitzer, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Mokhov, N. V. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Neuffer, D. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Palmer, M. A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Yonehara, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Snopok, P. [IIT, Chicago, IL (United States); Bogacz, A. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Roberts, T. J. [Muons Inc., Batavia, IL (United States); Delahaye, J. -P. [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-05-01

    Muon-based accelerators have the potential to enable facilities at both the Intensity and the Energy Frontiers. Muon storage rings can serve as high precision neutrino sources, and a muon collider is an ideal technology for a TeV or multi-TeV collider. Progress in muon accelerator designs has advanced steadily in recent years. In regard to 6D muon cooling, detailed and realistic designs now exist that provide more than 5 order-of-magnitude emittance reduction. Furthermore, detector performance studies indicate that with suitable pixelation and timing resolution, backgrounds in the collider detectors can be significantly reduced, thus enabling high-quality physics results. Thanks to these and other advances in design & simulation of muon systems, technology development, and systems demonstrations, muon storage-ring-based neutrino sources and a muon collider appear more feasible than ever before. A muon collider is now arguably among the most compelling approaches to a multi-TeV lepton collider. This paper summarizes the current status of design concepts for muon-based accelerators for neutrino factories and a muon collider.

  10. Understanding Angle and Angle Measure: A Design-Based Research Study Using Context Aware Ubiquitous Learning

    Science.gov (United States)

    Crompton, Helen

    2015-01-01

    Mobile technologies are quickly becoming tools found in the educational environment. The researchers in this study use a form of mobile learning to support students in learning about angle concepts. Design-based research is used in this study to develop an empirically-substantiated local instruction theory about students' develop of angle and…

  11. Statistical inference for extended or shortened phase II studies based on Simon's two-stage designs.

    Science.gov (United States)

    Zhao, Junjun; Yu, Menggang; Feng, Xi-Ping

    2015-06-07

    Simon's two-stage designs are popular choices for conducting phase II clinical trials, especially in the oncology trials to reduce the number of patients placed on ineffective experimental therapies. Recently Koyama and Chen (2008) discussed how to conduct proper inference for such studies because they found that inference procedures used with Simon's designs almost always ignore the actual sampling plan used. In particular, they proposed an inference method for studies when the actual second stage sample sizes differ from planned ones. We consider an alternative inference method based on likelihood ratio. In particular, we order permissible sample paths under Simon's two-stage designs using their corresponding conditional likelihood. In this way, we can calculate p-values using the common definition: the probability of obtaining a test statistic value at least as extreme as that observed under the null hypothesis. In addition to providing inference for a couple of scenarios where Koyama and Chen's method can be difficult to apply, the resulting estimate based on our method appears to have certain advantage in terms of inference properties in many numerical simulations. It generally led to smaller biases and narrower confidence intervals while maintaining similar coverages. We also illustrated the two methods in a real data setting. Inference procedures used with Simon's designs almost always ignore the actual sampling plan. Reported P-values, point estimates and confidence intervals for the response rate are not usually adjusted for the design's adaptiveness. Proper statistical inference procedures should be used.

  12. A Contradiction-Based Approach for Innovative Product Design

    Directory of Open Access Journals (Sweden)

    Ko Yao-Tsung

    2016-01-01

    Full Text Available Without creativity in design there is no potential for innovation. This paper investigates the role of contradictions in enhancing creativity in product design. Based on the inventive principles of TRIZ, this paper presents a novel design method by integrating technical and physical contradiction analysis methods into the conceptual design activities of new product development (NPD. Despite the recognized importance of innovative design, there is a lack of the systematic and effective design-thinking process that can covers all conceptual design activities. To address this gap, a sharper and fundamental model of the problem-solving is created for innovative product design based on the contradiction-oriented concept. Eventually, one case study is employed to illustrate the method and the result validates that it can help designers produce more creative outcomes in product design.

  13. A Survey study on design procedure of Seismic Base Isolation ...

    African Journals Online (AJOL)

    Adding shear walls or braced frames can decrease the potential damage caused by earthquakes.We can isolate the structures from the ground using the Seismic Base Isolation Systems that is flexible approach to decrease the potential damage. In this research we present information on the design procedure of seismic ...

  14. Design of Composite Structures Using Knowledge-Based and Case Based Reasoning

    Science.gov (United States)

    Lambright, Jonathan Paul

    1996-01-01

    A method of using knowledge based and case based reasoning to assist designers during conceptual design tasks of composite structures was proposed. The cooperative use of heuristics, procedural knowledge, and previous similar design cases suggests a potential reduction in design cycle time and ultimately product lead time. The hypothesis of this work is that the design process of composite structures can be improved by using Case-Based Reasoning (CBR) and Knowledge-Based (KB) reasoning in the early design stages. The technique of using knowledge-based and case-based reasoning facilitates the gathering of disparate information into one location that is easily and readily available. The method suggests that the inclusion of downstream life-cycle issues into the conceptual design phase reduces potential of defective, and sub-optimal composite structures. Three industry experts were interviewed extensively. The experts provided design rules, previous design cases, and test problems. A Knowledge Based Reasoning system was developed using the CLIPS (C Language Interpretive Procedural System) environment and a Case Based Reasoning System was developed using the Design Memory Utility For Sharing Experiences (MUSE) xviii environment. A Design Characteristic State (DCS) was used to document the design specifications, constraints, and problem areas using attribute-value pair relationships. The DCS provided consistent design information between the knowledge base and case base. Results indicated that the use of knowledge based and case based reasoning provided a robust design environment for composite structures. The knowledge base provided design guidance from well defined rules and procedural knowledge. The case base provided suggestions on design and manufacturing techniques based on previous similar designs and warnings of potential problems and pitfalls. The case base complemented the knowledge base and extended the problem solving capability beyond the existence of

  15. Implementing Project Based Learning Approach to Graphic Design Course

    Science.gov (United States)

    Riyanti, Menul Teguh; Erwin, Tuti Nuriah; Suriani, S. H.

    2017-01-01

    The purpose of this study was to develop a learning model based Commercial Graphic Design Drafting project-based learning approach, was chosen as a strategy in the learning product development research. University students as the target audience of this model are the students of the fifth semester Visual Communications Design Studies Program…

  16. Problem Based Game Design

    DEFF Research Database (Denmark)

    Reng, Lars; Schoenau-Fog, Henrik

    2011-01-01

    At Aalborg University’s department of Medialogy, we are utilizing the Problem Based Learning method to encourage students to solve game design problems by pushing the boundaries and designing innovative games. This paper is concerned with describing this method, how students employ it in various ...... projects and how they learn to analyse, design, and develop for innovation by using it. We will present various cases to exemplify the approach and focus on how the method engages students and aspires for innovation in digital entertainment and games.......At Aalborg University’s department of Medialogy, we are utilizing the Problem Based Learning method to encourage students to solve game design problems by pushing the boundaries and designing innovative games. This paper is concerned with describing this method, how students employ it in various...

  17. A Case Study on Collective Cognition and Operation in Team-Based Computer Game Design by Middle-School Children

    Science.gov (United States)

    Ke, Fengfeng; Im, Tami

    2014-01-01

    This case study examined team-based computer-game design efforts by children with diverse abilities to explore the nature of their collective design actions and cognitive processes. Ten teams of middle-school children, with a high percentage of minority students, participated in a 6-weeks, computer-assisted math-game-design program. Essential…

  18. Mobile Variable Depth Sampling System Design Study

    International Nuclear Information System (INIS)

    BOGER, R.M.

    2000-01-01

    A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study

  19. Mobile Variable Depth Sampling System Design Study

    Energy Technology Data Exchange (ETDEWEB)

    BOGER, R.M.

    2000-08-25

    A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study.

  20. Heavy-ion driver parametric studies and choice of a base 5 mega-joule driver design

    International Nuclear Information System (INIS)

    Bieri, R.; Meier, W.

    1992-01-01

    Parametric studies to optimize heavy-ion driver designs are described and an optimized 5 MJ driver design is described. Parametric studies are done on driver parameters including driver energy, number of beams, type of superconductor used in focusing magnets, maximum magnetic field allowed at the superconducting windings, axial quadrupole field packing fraction, ion mass, and ion charge state. All modeled drivers use the maximum beam currents allowed by the Maschke limits; driver scaling is described in a companion paper. The optimized driver described is conservative and cost effective. The base driver direct costs are only $120/Joule, and the base driver uses no recirculation, beam combination, or beam separation. The low driver cost achieved is due, in part, to the use of compact Nb 3 Sn quadrupole arrays, but results primarily from optimization over the large, multi-dimensional, parameter space available for heavy-ion drivers

  1. Towards evidence-based computational statistics: lessons from clinical research on the role and design of real-data benchmark studies.

    Science.gov (United States)

    Boulesteix, Anne-Laure; Wilson, Rory; Hapfelmeier, Alexander

    2017-09-09

    The goal of medical research is to develop interventions that are in some sense superior, with respect to patient outcome, to interventions currently in use. Similarly, the goal of research in methodological computational statistics is to develop data analysis tools that are themselves superior to the existing tools. The methodology of the evaluation of medical interventions continues to be discussed extensively in the literature and it is now well accepted that medicine should be at least partly "evidence-based". Although we statisticians are convinced of the importance of unbiased, well-thought-out study designs and evidence-based approaches in the context of clinical research, we tend to ignore these principles when designing our own studies for evaluating statistical methods in the context of our methodological research. In this paper, we draw an analogy between clinical trials and real-data-based benchmarking experiments in methodological statistical science, with datasets playing the role of patients and methods playing the role of medical interventions. Through this analogy, we suggest directions for improvement in the design and interpretation of studies which use real data to evaluate statistical methods, in particular with respect to dataset inclusion criteria and the reduction of various forms of bias. More generally, we discuss the concept of "evidence-based" statistical research, its limitations and its impact on the design and interpretation of real-data-based benchmark experiments. We suggest that benchmark studies-a method of assessment of statistical methods using real-world datasets-might benefit from adopting (some) concepts from evidence-based medicine towards the goal of more evidence-based statistical research.

  2. Study designs may influence results

    DEFF Research Database (Denmark)

    Johansen, Christoffer; Schüz, Joachim; Andreasen, Anne-Marie Serena

    2017-01-01

    appeared to show an inverse association, whereas nested case-control and cohort studies showed no association. For allergies, the inverse association was observed irrespective of study design. We recommend that the questionnaire-based case-control design be placed lower in the hierarchy of studies...... for establishing cause-and-effect for diseases such as glioma. We suggest that a state-of-the-art case-control study should, as a minimum, be accompanied by extensive validation of the exposure assessment methods and the representativeness of the study sample with regard to the exposures of interest. Otherwise...

  3. The household contact study design for genetic epidemiological studies of infectious diseases

    Directory of Open Access Journals (Sweden)

    Catherine eStein

    2013-04-01

    Full Text Available Most genetic epidemiological study designs fall into one of two categories: family-based and population-based (case-control. However, recent advances in statistical genetics call for study designs that combine these two approaches. We describe the household contact study design as we have applied it in our several years of study of the epidemiology of tuberculosis. Though we highlight its applicability for genetic epidemiological studies of infectious diseases, there are many facets of this design that are appealing for modern genetic studies, including the simultaneous enrollment of related and unrelated individuals, closely and distantly related individuals, collection of extensive epidemiologic and phenotypic data, and evaluation of effects of shared environment and gene by environment interaction. These study design characteristics are particularly appealing for current sequencing studies.

  4. Study on Feasibility of Applying Function Approximation Moment Method to Achieve Reliability-Based Design Optimization

    International Nuclear Information System (INIS)

    Huh, Jae Sung; Kwak, Byung Man

    2011-01-01

    Robust optimization or reliability-based design optimization are some of the methodologies that are employed to take into account the uncertainties of a system at the design stage. For applying such methodologies to solve industrial problems, accurate and efficient methods for estimating statistical moments and failure probability are required, and further, the results of sensitivity analysis, which is needed for searching direction during the optimization process, should also be accurate. The aim of this study is to employ the function approximation moment method into the sensitivity analysis formulation, which is expressed as an integral form, to verify the accuracy of the sensitivity results, and to solve a typical problem of reliability-based design optimization. These results are compared with those of other moment methods, and the feasibility of the function approximation moment method is verified. The sensitivity analysis formula with integral form is the efficient formulation for evaluating sensitivity because any additional function calculation is not needed provided the failure probability or statistical moments are calculated

  5. Conceptual design of jewellery: a space-based aesthetics approach

    Directory of Open Access Journals (Sweden)

    Tzintzi Vaia

    2017-01-01

    Full Text Available Conceptual design is a field that offers various aesthetic approaches to generation of nature-based product design concepts. Essentially, Conceptual Product Design (CPD uses similarities based on the geometrical forms and functionalities. Furthermore, the CAD-based freehand sketch is a primary conceptual tool in the early stages of the design process. The proposed Conceptual Product Design concept is dealing with jewelleries that are inspired from space. Specifically, a number of galaxy features, such as galaxy shapes, wormholes and graphical representation of planet magnetic field are used as inspirations. Those space-based design ideas at a conceptual level can lead to further opportunities for research and economic success of the jewellery industry. A number of illustrative case studies are presented and new opportunities can be derived for economic success.

  6. Managing the Complexity of Design Problems through Studio-Based Learning

    Science.gov (United States)

    Cennamo, Katherine; Brandt, Carol; Scott, Brigitte; Douglas, Sarah; McGrath, Margarita; Reimer, Yolanda; Vernon, Mitzi

    2011-01-01

    The ill-structured nature of design problems makes them particularly challenging for problem-based learning. Studio-based learning (SBL), however, has much in common with problem-based learning and indeed has a long history of use in teaching students to solve design problems. The purpose of this ethnographic study of an industrial design class,…

  7. Manufacturing system design based on axiomatic design: Case of assembly line

    Energy Technology Data Exchange (ETDEWEB)

    Hager, T.; Wafik, H.; Faouzi, M.

    2017-07-01

    In this paper, a combined Production Line Design (PLD) process which includes many design aspects is presented, developed and validated. Design/methodology/approach: The PLD process is based on the SADT (Structured Analysis and Design Technique) diagram and the Axiomatic Design (AD) method. Practical implications: For a purpose of validation, this proposed process has been applied in a manufacturing company and it has been validated by simulation. Findings: The results of the validation indicated that the production line designed by this process is outperformed the initial line of the company. Originality/value: Recently, the problems of production line design (PLD) have attracted the attention of many researchers. However, only a few studies have treated the PLD which includes all design aspects. In this work, a combined PLD process is presented. It should be noted that the proposed process is simple and effective.

  8. Manufacturing system design based on axiomatic design: Case of assembly line

    International Nuclear Information System (INIS)

    Hager, T.; Wafik, H.; Faouzi, M.

    2017-01-01

    In this paper, a combined Production Line Design (PLD) process which includes many design aspects is presented, developed and validated. Design/methodology/approach: The PLD process is based on the SADT (Structured Analysis and Design Technique) diagram and the Axiomatic Design (AD) method. Practical implications: For a purpose of validation, this proposed process has been applied in a manufacturing company and it has been validated by simulation. Findings: The results of the validation indicated that the production line designed by this process is outperformed the initial line of the company. Originality/value: Recently, the problems of production line design (PLD) have attracted the attention of many researchers. However, only a few studies have treated the PLD which includes all design aspects. In this work, a combined PLD process is presented. It should be noted that the proposed process is simple and effective.

  9. Market orientated design studies for SOFC based systems

    Energy Technology Data Exchange (ETDEWEB)

    Nietsch, T.; Clark, J.

    1999-07-01

    This report examines the development status of Solid Oxide Fuel Cell (SOFC) technology, assesses its commercial potential for heat and power generation in the UK and identifies key development areas for both the SOFC stack and associated system components. A range of Distributed Generation (DG) and Combined Heat and Power (CHP) applications were considered in arriving at these recommendations. The project commenced with initial surveys of leading SOFC technology companies and centres world-wide. These surveys were conducted in parallel with consultations with key operator organisations in the UK which enabled the requirements of these organisations within the UK Energy Supply Industry to be identified. As a result of the initial survey, over 30 fuel cell based power plants, of size ranging from 1 kW{sub e} to 20 MW{sub e} for both DG and CHP applications, were identified. Outline designs of these applications were then set up and simulated. These candidate systems were then assessed against each other in terms of efficiency, cost of electricity, specific costs, technical risk and market potential for the UK industry. The final ranking obtained was then confirmed with the key operator organisations. On the basis of the ranking process noted above, nine SOFC based power generation/CHP applications were chosen for more detailed investigation in terms of their potential in both UK and overseas markets. Detailed simulations were conducted for each application to allow study of: the influence of efficiency on the economics of the different plants/stacks; the combination of stack and Balance of Plant (BoP) costs; and the cost and availability of key balance of plant devices. These systems were then again assessed in terms of the criteria noted for the outline stage. Finally key development areas for both SOFC stacks and associated Balance of Plant devices were identified. (author)

  10. FED/INTOR reactor design studies

    International Nuclear Information System (INIS)

    Brown, T.G.; Cramer, B.A.; Davisson, J.P.; Kunselman, M.H.; Reiersen, W.T.; Sager, P.H.; Strickler, D.J.

    1982-03-01

    Upon completing the design studies identified in this report, an overall assessment of the design options is made that will form the bases to define the configuration of the next major Tokamak device. The TF coil size will be defined, along with the vacuum boundary, the PF coil arrangement, and the torus configuration. After the configuration is established, an overall performance and cost re-assessment should be made to finally trade off device performance with machine capital and operating costs to establish a reactor design point for a given set of design requirements

  11. Designing for Nomadic Play: A case study of participatory design with children

    DEFF Research Database (Denmark)

    Brynskov, Martin; Christensen, Bent Guldbjerg; Ludvigsen, Martin

    This poster presents the results from an empirical probe study trying to engage children creatively in the design process of systems and artifacts that support nomadic life-style. Based on observational studies and interviews with children of different ages (5-15 years), we conducted a participat......This poster presents the results from an empirical probe study trying to engage children creatively in the design process of systems and artifacts that support nomadic life-style. Based on observational studies and interviews with children of different ages (5-15 years), we conducted...... a participatory design workshop cycle where children were encouraged to envision and virtually play with not-yet-invented future technology. Findings include qualitative characterizations of children’s activities (e.g. ‘play’ culture, use of digital media, age and gender differences, relation to space...

  12. Infusing Technology Driven Design Thinking in Industrial Design Education: A Case Study

    Science.gov (United States)

    Mubin, Omar; Novoa, Mauricio; Al Mahmud, Abdullah

    2017-01-01

    Purpose: This paper narrates a case study on design thinking-based education work in an industrial design honours program. Student projects were developed in a multi-disciplinary setting across a Computing and Engineering faculty that allowed promoting technologically and user-driven innovation strategies. Design/methodology/approach: A renewed…

  13. Review of research in feature based design

    NARCIS (Netherlands)

    Salomons, O.W.; van Houten, Frederikus J.A.M.; Kals, H.J.J.

    1993-01-01

    Research in feature-based design is reviewed. Feature-based design is regarded as a key factor towards CAD/CAPP integration from a process planning point of view. From a design point of view, feature-based design offers possibilities for supporting the design process better than current CAD systems

  14. Epitope-based peptide vaccine design and target site depiction against Ebola viruses: an immunoinformatics study.

    Science.gov (United States)

    Khan, M A; Hossain, M U; Rakib-Uz-Zaman, S M; Morshed, M N

    2015-07-01

    Ebola viruses (EBOVs) have been identified as an emerging threat in recent year as it causes severe haemorrhagic fever in human. Epitope-based vaccine design for EBOVs remains a top priority because a mere progress has been made in this regard. Another reason is the lack of antiviral drug and licensed vaccine although there is a severe outbreak in Central Africa. In this study, we aimed to design an epitope-based vaccine that can trigger a significant immune response as well as to prognosticate inhibitor that can bind with potential drug target sites using various immunoinformatics and docking simulation tools. The capacity to induce both humoral and cell-mediated immunity by T cell and B cell was checked for the selected protein. The peptide region spanning 9 amino acids from 42 to 50 and the sequence TLASIGTAF were found as the most potential B and T cell epitopes, respectively. This peptide could interact with 12 HLAs and showed high population coverage up to 80.99%. Using molecular docking, the epitope was further appraised for binding against HLA molecules to verify the binding cleft interaction. In addition with this, the allergenicity of the epitopes was also evaluated. In the post-therapeutic strategy, docking study of predicted 3D structure identified suitable therapeutic inhibitor against targeted protein. However, this computational epitope-based peptide vaccine designing and target site prediction against EBOVs open up a new horizon which may be the prospective way in Ebola viruses research; the results require validation by in vitro and in vivo experiments. © 2015 John Wiley & Sons Ltd.

  15. Reusing Design Knowledge Based on Design Cases and Knowledge Map

    Science.gov (United States)

    Yang, Cheng; Liu, Zheng; Wang, Haobai; Shen, Jiaoqi

    2013-01-01

    Design knowledge was reused for innovative design work to support designers with product design knowledge and help designers who lack rich experiences to improve their design capacity and efficiency. First, based on the ontological model of product design knowledge constructed by taxonomy, implicit and explicit knowledge was extracted from some…

  16. Application Design Of Interactive Multimedia Development Based Motion Graphic On Making Fashion Design Learning In Digital Format

    Directory of Open Access Journals (Sweden)

    Winwin Wiana

    2017-05-01

    Full Text Available This study is a research and development aimed at developing multimedia interactive learning based animation as an effort to improve student learning motivation in learning Fashion Design Technology apart from this study also aims to design a learning program courses Fashion Design Technology with a focus on optimizing the use of interactive media in learning process. From this study showed 1 A preliminary study found that the problems faced by students when studying Fashion Design Technology is the student is not optimal when learning designing clothes based computer technology both in terms of learning content learning mechanisms that still uses a linear media and limitations of highly structured learning time. 2 Animation multimedia has the following characteristics a media of learning is convergent interactive self-contained in the sense of giving convenience to users without the guidance of others as multimedia applications can present the material to see more interesting and informative. 3 Design of multimedia learning software developed include the creation of flowcharts storyboards and drafting manuscript of interactive multimedia based animation. 4 Based on the results of validation by multimedia experts obtained an average percentage of 85.55 viability of the material experts obtained an average percentage of 90.84 viability and by students as users gained an average percentage of 96.38 eligibility so it can be said that the standard of the feasibility of interactive multimedia based animation developed is included in the category of Very High or Very Good. Furthermore experts agree that the development of interactive multimedia based animation on learning Fashion Design Technology can be used with some aspects that need to be improved to obtain higher levels of feasibility more optimal.

  17. TP-model transformation-based-control design frameworks

    CERN Document Server

    Baranyi, Péter

    2016-01-01

    This book covers new aspects and frameworks of control, design, and optimization based on the TP model transformation and its various extensions. The author outlines the three main steps of polytopic and LMI based control design: 1) development of the qLPV state-space model, 2) generation of the polytopic model; and 3) application of LMI to derive controller and observer. He goes on to describe why literature has extensively studied LMI design, but has not focused much on the second step, in part because the generation and manipulation of the polytopic form was not tractable in many cases. The author then shows how the TP model transformation facilitates this second step and hence reveals new directions, leading to powerful design procedures and the formulation of new questions. The chapters of this book, and the complex dynamical control tasks which they cover, are organized so as to present and analyze the beneficial aspect of the family of approaches (control, design, and optimization). Additionally, the b...

  18. Case Study of CPT-based Design Methods for Axial Capacity of Driven Piles in Sand

    DEFF Research Database (Denmark)

    Thomassen, Kristina; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2012-01-01

    loaded offshore driven piles in cohesionless soil has until now been the β-method given in API. The API-method is based on the effective overburden pressure at the depth in question. Previous studies show deviations between full-scale load test measurements of the axial pile capacity and the predictions...... found by means of the API-method. Compared to the test measurements, the API-method under-estimates the capacity of short piles (piles in loose sand, and gives a shaft capacity less conservative for piles in tension than for piles in compression......Today the design of onshore axially loaded driven piles in cohesionless soil is commonly made on basis of CPT-based methods because field investigations have shown strong correlation between the local shaft friction and the CPT cone resistance. However, the recommended design method for axially...

  19. The design of scenario-based training from the resilience engineering perspective: a study with grid electricians.

    Science.gov (United States)

    Saurin, Tarcisio Abreu; Wachs, Priscila; Righi, Angela Weber; Henriqson, Eder

    2014-07-01

    Although scenario-based training (SBT) can be an effective means to help workers develop resilience skills, it has not yet been analyzed from the resilience engineering (RE) perspective. This study introduces a five-stage method for designing SBT from the RE view: (a) identification of resilience skills, work constraints and actions for re-designing the socio-technical system; (b) design of template scenarios, allowing the simulation of the work constraints and the use of resilience skills; (c) design of the simulation protocol, which includes briefing, simulation and debriefing; (d) implementation of both scenarios and simulation protocol; and (e) evaluation of the scenarios and simulation protocol. It is reported how the method was applied in an electricity distribution company, in order to train grid electricians. The study was framed as an application of design science research, and five research outputs are discussed: method, constructs, model of the relationships among constructs, instantiations of the method, and theory building. Concerning the last output, the operationalization of the RE perspective on three elements of SBT is presented: identification of training objectives; scenario design; and debriefing. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Case Studies of Secondary School Teachers Designing Socioscientific Issues-Based Instruction and Their Students' Socioscientific Reasoning

    Science.gov (United States)

    Karahan, Engin

    Addressing socioscientific issues (SSI) has been one of the main focuses in science education since the Science, Technology, and Society (STS) movement in the 1970s (Levinson, 2006); however, teaching controversial socioscientific issues has always been challenging for teachers (Dillon, 1994; Osborne, Duschl, & Fairbrother, 2002). Although teachers exhibit positive attitudes for using controversial socioscientific issues in their science classrooms, only a small percentage of them actually incorporate SSI content into their science curricula on a regular basis (Sadler, Amirshokoohi, Kazempour, & Allspaw, 2006; Lee & Witz, 2009). The literature in science education has highlighted the signi?cant relationships among teacher beliefs, teaching practices, and student learning (Bryan & Atwater, 2002; King, Shumow, & Lietz, 2001; Lederman, 1992). Despite the fact that the case studies present a relatively detailed picture of teachers' values and motivations for teaching SSI (e.g. Lee, 2006; Lee & Witz, 2009; Reis & Galvao, 2004), these studies still miss the practices of these teachers and potential outcomes for their students. Therefore, there is a great need for in-depth case studies that would focus on teachers' practices of designing and teaching SSI-based learning environments, their deeper beliefs and motivations for teaching SSI, and their students' response to these practices (Lee, 2006). This dissertation is structured as three separate, but related, studies about secondary school teachers' experiences of designing and teaching SSI-based classes and their students' understanding of science and SSI reasoning. The case studies in this dissertation seek answers for (1) teachers' practices of designing and teaching SSI-based instruction, as well as its relation to their deeper personal beliefs and motivations to teach SSI, and (2) how their students respond to their approaches of teaching SSI in terms of their science understanding and SSI reasoning. The first paper

  1. The Research of Design Based on Social Commerce

    OpenAIRE

    Juhua Wu; Meng Xu; Zan Mo; Luo Liao

    2015-01-01

    Based on previous design theories which focus only on artifacts, we study the factors of social commerce design with application environment and human capabilities. By comparing social commerce design model and information model, we develop a new social commerce design model, further exploring user requirements after shopping, including the exploration of brand community, sharing offline social shopping experience and the improvement of user social skills. According to the new model, we revea...

  2. Design principles for simulation games for learning clinical reasoning: A design-based research approach.

    Science.gov (United States)

    Koivisto, J-M; Haavisto, E; Niemi, H; Haho, P; Nylund, S; Multisilta, J

    2018-01-01

    Nurses sometimes lack the competence needed for recognising deterioration in patient conditions and this is often due to poor clinical reasoning. There is a need to develop new possibilities for learning this crucial competence area. In addition, educators need to be future oriented; they need to be able to design and adopt new pedagogical innovations. The purpose of the study is to describe the development process and to generate principles for the design of nursing simulation games. A design-based research methodology is applied in this study. Iterative cycles of analysis, design, development, testing and refinement were conducted via collaboration among researchers, educators, students, and game designers. The study facilitated the generation of reusable design principles for simulation games to guide future designers when designing and developing simulation games for learning clinical reasoning. This study makes a major contribution to research on simulation game development in the field of nursing education. The results of this study provide important insights into the significance of involving nurse educators in the design and development process of educational simulation games for the purpose of nursing education. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Data to inform a social media component for professional development and practices: A design-based research study.

    Science.gov (United States)

    Novakovich, Jeanette; Shaw, Steven; Miah, Sophia

    2017-02-01

    This DIB article includes the course artefacts, instruments, survey data, and descriptive statistics, along with in-depth correlational analysis for the first iteration of a design-based research study on designing curriculum for developing online professional identity and social media practices for a multi-major advanced professional writing course. Raw data was entered into SPSS software. For interpretation and discussion, please see the original article entitled, "Designing curriculum to shape professional social media skills and identity in virtual communities of practice" (J. Novakovich, S. Miah, S. Shaw, 2017) [1].

  4. Plant aging and design bases documentation

    International Nuclear Information System (INIS)

    Kelly, J.

    1985-01-01

    As interest in plant aging and lifetime extension continues to grow, the need to identify and capture the original design bases for the plant becomes more urgent. Decisions on lifetime extension and availability must be based on a rational understanding of design input, assumptions, and objectives. As operating plant time accumulates, the history of the early design begins to fade. The longer the utility waits, the harder it will be to re-establish the original design bases. Therefore, the time to develop this foundation is now. This paper demonstrates the impact that collecting and maintaining the original design bases of the plant can have on a utility's lifetime extension program. This impact becomes apparent when considering the technical, regulatory and financial aspects of lifetime extension. It is not good enough to know that the design information is buried somewhere in the corporate archives, and that given enough time, it could be retrieved. To be useful to the lifetime extension program, plant design information must be concise, readily available (i.e., retrievable), and easy to use. These objectives can only be met through a systematic program for collecting and presenting plant design documentation. To get the maximum benefit from a lifetime extension program, usable design bases documentation should be available as early in the plant life as possible. It will help identify areas that require monitoring today so that data is available to make rational decisions in the future

  5. Application Design Of Interactive Multimedia Development Based Motion Graphic On Making Fashion Design Learning In Digital Format

    OpenAIRE

    Winwin Wiana

    2017-01-01

    This study is a research and development aimed at developing multimedia interactive learning based animation as an effort to improve student learning motivation in learning Fashion Design Technology apart from this study also aims to design a learning program courses Fashion Design Technology with a focus on optimizing the use of interactive media in learning process. From this study showed 1 A preliminary study found that the problems faced by students when studying Fashion Design Technology...

  6. Assessment of LWR spent fuel disposal options. Volume 3. Study bases and system design considerations (Appendices). Technical report

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    Volume 3 (Appendices) provides a tabulation of the bases and assumptions used in the study as well as preconceptual design description and cost estimates of the facilities and transportation systems necessary to implement the various study cases.

  7. Assessment of LWR spent fuel disposal options. Volume 3. Study bases and system design considerations (Appendices). Technical report

    International Nuclear Information System (INIS)

    1979-07-01

    Volume 3 (Appendices) provides a tabulation of the bases and assumptions used in the study as well as preconceptual design description and cost estimates of the facilities and transportation systems necessary to implement the various study cases

  8. Bridging the Gap: A Design-based Case Study of a Mathematics Skills Intervention Program

    OpenAIRE

    Safaralian, Leila

    2017-01-01

    Abstract of the DissertationBridge the Gap: A Design-based Case Study of a Mathematics Skills Intervention ProgrambyLeila SafaralianDoctor of Education in Educational LeadershipUniversity of California, San Diego, 2017California State University, San Marcos, 2017Kenneth P. Gonzalez, ChairMany students aspire to continue their educational journey, but far too many enter college without the basic content knowledge, skills, or habits of mind needed to succeed. Research on college readiness indic...

  9. Competency Based Assessment in Fashion Design

    Science.gov (United States)

    Russanti, Irma; Nurlaela, Lutfiyah; Basuki, Ismet; Munoto

    2018-04-01

    Professional certification is a form of stipulation on certain competency standards provided by one professional organization to the performance of a person through assessment. For that an assessment needs to be standardized so that there exists a general standardized scale to measure competence. In the professional certification of fashion design department, an instrument of competency based assessment is essential to be developed. The purpose of this review is to know the application of competency based assessment in the field of fashion design. The literature reviews were found by journal searching with keywords competency based assessment and fashion design in Google scholar, of which was gotten over 20 journals from 2006 to 2016. Afterwards, the search of the free-downloaded e-books in libgen was conducted under competency based assessment and fashion design, which is then found some related references. The obtained literatures were used to review the definition, approach, and implementation of competency based assessment in the field of fashion design. Results show that it is important to develop an assessment sheet in the field of fashion design covering garment, apparel and embroidery sectors by patterning the criteria of performers along with the qualifications.

  10. Study, design and manufacture eddy current probes for industry applications

    International Nuclear Information System (INIS)

    Nguyen Phuc; Nguyen Van Thuy; Vuong Binh Duong; Do Minh Duc; Trinh Dinh Truong; Tran Trong Duc; Do Tung Khanh; Dang Quang Trung

    2016-01-01

    This study is based on the studying, designing and manufacturing of eddy current probes for industry applications. The main tasks of this study include: i) Describes the overview and classification of eddy current probes (which can be classified into three categories based on the mode of operation: absolute eddy current probe, differential eddy current probe and reflect eddy current probe); ii) Describes the three methods of probe designing and manufacturing (including experimental, analytical and numerical designs); iii) Describes the designing and manufacturing of eddy current probes for industry applications, which based on experimental and analytical methods. Based on this study, we have successfully manufactured some current probes (including absolute eddy current probe, differential eddy current probe and reflect eddy current probe) for surface and tube inspections. (author)

  11. LMI–based robust controller design approach in aircraft multidisciplinary design optimization problem

    Directory of Open Access Journals (Sweden)

    Qinghua Zeng

    2015-07-01

    Full Text Available This article proposes a linear matrix inequality–based robust controller design approach to implement the synchronous design of aircraft control discipline and other disciplines, in which the variation in design parameters is treated as equivalent perturbations. Considering the complicated mapping relationships between the coefficient arrays of aircraft motion model and the aircraft design parameters, the robust controller designed is directly based on the variation in these coefficient arrays so conservative that the multidisciplinary design optimization problem would be too difficult to solve, or even if there is a solution, the robustness of design result is generally poor. Therefore, this article derives the uncertainty model of disciplinary design parameters based on response surface approximation, converts the design problem of the robust controller into a problem of solving a standard linear matrix inequality, and theoretically gives a less conservative design method of the robust controller which is based on the variation in design parameters. Furthermore, the concurrent subspace approach is applied to the multidisciplinary system with this kind of robust controller in the design loop. A multidisciplinary design optimization of a tailless aircraft as example is shown that control discipline can be synchronous optimal design with other discipline, especially this method will greatly reduce the calculated amount of multidisciplinary design optimization and make multidisciplinary design optimization results more robustness of flight performance.

  12. Case-Based Instructional Practices: A Multiple-Case Study from Torts, Marketing, and Online Instructional Design Classes

    Science.gov (United States)

    Jung, Ji yoon

    2017-01-01

    The purpose of this study is to provide a comprehensive account on case-based instructional practices. Semester-long participant observation records in torts, marketing, and online instructional design classes, instructor interviews, course syllabi and teaching materials were used to describe the within-class complexity of the practices in terms…

  13. Study on general design of dual-DMD based infrared two-band scene simulation system

    Science.gov (United States)

    Pan, Yue; Qiao, Yang; Xu, Xi-ping

    2017-02-01

    Mid-wave infrared(MWIR) and long-wave infrared(LWIR) two-band scene simulation system is a kind of testing equipment that used for infrared two-band imaging seeker. Not only it would be qualified for working waveband, but also realize the essence requests that infrared radiation characteristics should correspond to the real scene. Past single-digital micromirror device (DMD) based infrared scene simulation system does not take the huge difference between targets and background radiation into account, and it cannot realize the separated modulation to two-band light beam. Consequently, single-DMD based infrared scene simulation system cannot accurately express the thermal scene model that upper-computer built, and it is not that practical. To solve the problem, we design a dual-DMD based, dual-channel, co-aperture, compact-structure infrared two-band scene simulation system. The operating principle of the system is introduced in detail, and energy transfer process of the hardware-in-the-loop simulation experiment is analyzed as well. Also, it builds the equation about the signal-to-noise ratio of infrared detector in the seeker, directing the system overall design. The general design scheme of system is given, including the creation of infrared scene model, overall control, optical-mechanical structure design and image registration. By analyzing and comparing the past designs, we discuss the arrangement of optical engine framework in the system. According to the main content of working principle and overall design, we summarize each key techniques in the system.

  14. Model-Based Engineering Design for Trade Space Exploration throughout the Design Cycle

    Science.gov (United States)

    Lamassoure, Elisabeth S.; Wall, Stephen D.; Easter, Robert W.

    2004-01-01

    This paper presents ongoing work to standardize model-based system engineering as a complement to point design development in the conceptual design phase of deep space missions. It summarizes two first steps towards practical application of this capability within the framework of concurrent engineering design teams and their customers. The first step is standard generation of system sensitivities models as the output of concurrent engineering design sessions, representing the local trade space around a point design. A review of the chosen model development process, and the results of three case study examples, demonstrate that a simple update to the concurrent engineering design process can easily capture sensitivities to key requirements. It can serve as a valuable tool to analyze design drivers and uncover breakpoints in the design. The second step is development of rough-order- of-magnitude, broad-range-of-validity design models for rapid exploration of the trade space, before selection of a point design. At least one case study demonstrated the feasibility to generate such models in a concurrent engineering session. The experiment indicated that such a capability could yield valid system-level conclusions for a trade space composed of understood elements. Ongoing efforts are assessing the practicality of developing end-to-end system-level design models for use before even convening the first concurrent engineering session, starting with modeling an end-to-end Mars architecture.

  15. Instruction in Divergent Thinking for Conceptual Design: A Case Study Based on a Corkscrew

    OpenAIRE

    Ying-Chieh Liu; Chin-Yu Kao; Amaresh Chakrabarti

    2015-01-01

    Abstraction is a powerful tool for designers in the conceptual design stage. Such abstractions take various forms, and little is known as to how a particular method of abstraction would support designers in specific design cases. A method is proposed which includes a deliberate step for divergent thinking. The method presents learners with an abstract representation of an existing artifact, and encourages them to explore potential concepts that are different in style but are based on the same...

  16. Design-based learning in classrooms using playful digital toolkits

    NARCIS (Netherlands)

    Scheltenaar, K.J.; van der Poel, J.E.C.; Bekker, Tilde

    2015-01-01

    The goal of this paper is to explore how to implement Design Based Learning (DBL) with digital toolkits to teach 21st century skills in (Dutch) schools. It describes the outcomes of a literature study and two design case studies in which such a DBL approach with digital toolkits was iteratively

  17. Towards evidence-based computational statistics: lessons from clinical research on the role and design of real-data benchmark studies

    Directory of Open Access Journals (Sweden)

    Anne-Laure Boulesteix

    2017-09-01

    Full Text Available Abstract Background The goal of medical research is to develop interventions that are in some sense superior, with respect to patient outcome, to interventions currently in use. Similarly, the goal of research in methodological computational statistics is to develop data analysis tools that are themselves superior to the existing tools. The methodology of the evaluation of medical interventions continues to be discussed extensively in the literature and it is now well accepted that medicine should be at least partly “evidence-based”. Although we statisticians are convinced of the importance of unbiased, well-thought-out study designs and evidence-based approaches in the context of clinical research, we tend to ignore these principles when designing our own studies for evaluating statistical methods in the context of our methodological research. Main message In this paper, we draw an analogy between clinical trials and real-data-based benchmarking experiments in methodological statistical science, with datasets playing the role of patients and methods playing the role of medical interventions. Through this analogy, we suggest directions for improvement in the design and interpretation of studies which use real data to evaluate statistical methods, in particular with respect to dataset inclusion criteria and the reduction of various forms of bias. More generally, we discuss the concept of “evidence-based” statistical research, its limitations and its impact on the design and interpretation of real-data-based benchmark experiments. Conclusion We suggest that benchmark studies—a method of assessment of statistical methods using real-world datasets—might benefit from adopting (some concepts from evidence-based medicine towards the goal of more evidence-based statistical research.

  18. SLS Navigation Model-Based Design Approach

    Science.gov (United States)

    Oliver, T. Emerson; Anzalone, Evan; Geohagan, Kevin; Bernard, Bill; Park, Thomas

    2018-01-01

    The SLS Program chose to implement a Model-based Design and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team has been responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for the navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1-B design, the additional GPS Receiver hardware is managed as a DMM at the vehicle design level. This paper provides a discussion of the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the Navigation components. These include composing system requirements, requirements verification, model development, model verification and validation, and modeling and analysis approaches. The Model-based Design and Requirements approach does not reduce the effort associated with the design process versus previous processes used at Marshall Space Flight Center. Instead, the approach takes advantage of overlap between the requirements development and management process, and the design and analysis process by efficiently combining the control (i.e. the requirement) and the design mechanisms. The design mechanism is the representation of the component behavior and performance in design and analysis tools. The focus in the early design process shifts from the development and

  19. Implementation and application study on 3D collaborative design for CFETR based on ENOVIA VPM

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Ling-Long, E-mail: linglonglin@ipp.ac.cn [Tokamak Design Division, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Song, Yun-Tao [Tokamak Design Division, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China); Tang, Yu-Xiang [Tokamak Design Division, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Du, Qing-Qing [Hefei Keju Cryogenics Co., Ltd., Hefei, Anhui 230031 (China); Gong, Yi-Peng [Shanghai ATOZ Group Co., Ltd., Shanghai 201611, P.R. China. (China)

    2015-11-15

    China Fusion Engineering Test Reactor (CFETR) is an ITER-like superconducting tokamak device and it is under conceptual design. The paper is to highlight the building of the collaborative platform and its application in design work. First, a collaborative framework between collaborators is proposed and a method based-on Riverbed to optimize WAN is adopted to improve the data transmission. Then it proposes a Unified Modeling Language (UML) approach for specification of PDM (Product Documents Management) system implementation to enable management of whole product data and related information about its entire lifecycle. At last, the chosen approach for modeling based on UML is detailed and the relational design based-on skeleton is instanced for CFETR.

  20. Implementation and application study on 3D collaborative design for CFETR based on ENOVIA VPM

    International Nuclear Information System (INIS)

    Lin, Ling-Long; Song, Yun-Tao; Tang, Yu-Xiang; Du, Qing-Qing; Gong, Yi-Peng

    2015-01-01

    China Fusion Engineering Test Reactor (CFETR) is an ITER-like superconducting tokamak device and it is under conceptual design. The paper is to highlight the building of the collaborative platform and its application in design work. First, a collaborative framework between collaborators is proposed and a method based-on Riverbed to optimize WAN is adopted to improve the data transmission. Then it proposes a Unified Modeling Language (UML) approach for specification of PDM (Product Documents Management) system implementation to enable management of whole product data and related information about its entire lifecycle. At last, the chosen approach for modeling based on UML is detailed and the relational design based-on skeleton is instanced for CFETR.

  1. Novel Study Guides for Biochemistry Meaningful Learning in Biology: a Design-Based Research

    Directory of Open Access Journals (Sweden)

    Costa, C ; Galembeck, E. Costa, C ; Galembeck, E.

    2017-07-01

    Full Text Available One of the difficulties for biochemistry learning is the persistence of traditional teaching methods, based on transmission and memorization of abstract and detailed information, usually in a decontextualized way. Such scenario results in surface learning and content reproduction. In order to address these problems, three interventions in a discipline (Metabolism for Biology majors were applied, in the form of innovative teaching tools (study guides. OBJECTIVES: The main goal is to evaluate the impact of these interventions on interest, motivation, and learning of the metabolic pathways. MATERIALS AND METHODS: We describe the development, application, and evaluation of two study guides – one created from a problem used as a contextual connection for glycogen metabolism study and another embedding an integrative view based on glutamate metabolism. Both materials were guided by broad themes like evolution, metabolic adaptation, and comparative biochemistry. The development of the study guides combined submicroscopic (molecular and macroscopic (body, environment levels, aiming to motivate reading and discussion. A design-based research with cycles of application and assessment was carried out, by means of classroom observation, grade analysis in written exams, and students’ interviews. RESULTS AND DISCUSSION: In general, based on in-class student feedback to professors and to the researcher in the interviews, the study guides arouse curiosity and fostered peer discussion. Final average grades indicate a good global performance in all proposed activities. Whole data from study guides’ application in classroom evidenced their impact on interest, motivation, and learning. The strategy of developing problem or integrative situation linking molecular (micro and contextual (macro levels were helpful to foster critical thinking and to value topics of scientific literacy. CONCLUSIONS: Analysis and interpretation of the results point to benefits for

  2. Implementing a Generative Urban Design Model : Grammar-based design patterns for urban design

    NARCIS (Netherlands)

    Beirao, J.N.; Mendes, G.; Duarte, J.; Stouffs, R.M.F.

    2010-01-01

    This paper shows the first results of a prototype implementation of a generative urban design tool. This implementation will form part of a design support tool for a GIS based platform defined to formulate, generate and evaluate urban designs. These three goals, formulation, generation and

  3. Group-Based Life Design Counseling in an Italian Context

    Science.gov (United States)

    Di Fabio, Annamaria; Maree, Jacobus Gideon

    2012-01-01

    This study examined the effectiveness of group-based Life Design Counseling using the Career-Story Interview. Written exercises were used to implement the seven topics in the Career-Story Interview. The present study employed an experimental design that involved two groups of Italian entrepreneurs from the agricultural and trade sectors, namely an…

  4. Designing Task-Based Syllabus For Writing Class

    Directory of Open Access Journals (Sweden)

    Sundari Hanna

    2018-01-01

    Full Text Available Writing is viewed as the most complex skill to learn and to teach. Beside learner factors, teacher, materials and syllabus may also affect the process of learning language as foreign language. Syllabus, in general, can be defined as a set of what is taught (content and the way it is taught (procedure. This current research aims to design a task-based syllabus for writing class at university level. This study was conducted by qualitative descriptive design with 92 students and 4 lecturers as respondents. As part of research and development project in one private university in Jakarta, a developed task-based syllabus was based on need analysis and the principles of task-based language teaching. Students’ proficiency levels are fair with sentence patterns and grammar as the most difficult aspects. Academic writing is more preferable orientation with the small portions of creative writing. Then, the developed task-based syllabus has been proposed for writing class which covers the components of goal (learning outcome, course description and objectives, a set of writing tasks, features of content focus and language focus and course evaluation. The developed syllabus, then, can guide the lecturers in designing lesson plan and selecting materials for writing class.

  5. Assessing model-based reasoning using evidence-centered design a suite of research-based design patterns

    CERN Document Server

    Mislevy, Robert J; Riconscente, Michelle; Wise Rutstein, Daisy; Ziker, Cindy

    2017-01-01

    This Springer Brief provides theory, practical guidance, and support tools to help designers create complex, valid assessment tasks for hard-to-measure, yet crucial, science education standards. Understanding, exploring, and interacting with the world through models characterizes science in all its branches and at all levels of education. Model-based reasoning is central to science education and thus science assessment. Current interest in developing and using models has increased with the release of the Next Generation Science Standards, which identified this as one of the eight practices of science and engineering. However, the interactive, complex, and often technology-based tasks that are needed to assess model-based reasoning in its fullest forms are difficult to develop. Building on research in assessment, science education, and learning science, this Brief describes a suite of design patterns that can help assessment designers, researchers, and teachers create tasks for assessing aspects of model-based...

  6. Design, synthesis and photophysical studies of dipyrromethene-based materials: insights into their applications in organic photovoltaic devices.

    Science.gov (United States)

    Bessette, André; Hanan, Garry S

    2014-05-21

    This review article presents the most recent developments in the use of materials based on dipyrromethene (DPM) and azadipyrromethenes (ADPM) for organic photovoltaic (OPV) applications. These chromophores and their corresponding BF2-chelated derivatives BODIPY and aza-BODIPY, respectively, are well known for fluorescence-based applications but are relatively new in the field of photovoltaic research. This review examines the variety of relevant designs, synthetic methodologies and photophysical studies related to materials that incorporate these porphyrinoid-related dyes in their architecture. The main idea is to inspire readers to explore new avenues in the design of next generation small-molecule and bulk-heterojunction solar cell (BHJSC) OPV materials based on DPM chromophores. The main concepts are briefly explained, along with the main challenges that are to be resolved in order to take full advantage of solar energy.

  7. A Study of an Architecture Design Learning Process Based on Social Learning, Course Teaching, Interaction, and Analogical Thinking

    Directory of Open Access Journals (Sweden)

    Yun-Wu Wu

    2014-01-01

    Full Text Available The students in the vocational education of architecture design in Taiwan often face many learning obstacles, such as no problem solving ability and lack of creativity. Therefore, this study used a social learning model as a learning strategy in the architecture design learning process to solve related learning difficulties. Firstly, this study used cognitive development teaching activities and a learning process based on analogical thinking and analogical reasoning to build the social learning model. Secondly, the social learning model of this study was implemented in the teaching of a required course of architecture design for 120 freshmen in China University of Technology. The questionnaire survey results were then statically analyzed and compared to measure the differences in the students’ knowledge about architecture designs before and after the teaching in this study. In this study, the social learning model is proven helpful in inspiring the students’ creativity by converting new knowledge of architecture design into schemas and hence retaining the new knowledge for future application. The social learning model can be applied in the teaching of architecture design in other schools, while more research can be conducted in the future to further confirm its feasibility to promote effective learning.

  8. Visualizing Practices in Project-based Design

    DEFF Research Database (Denmark)

    Whyte, Jennifer; Tryggestad, Kjell; Comi, Alice

    2016-01-01

    Project-based design involves a variety of visual representations, which are evolved to make decisions and accomplish project objectives. Yet, such mediated and distributed ways of working are difficult to capture through ethnographies that examine situated design. A novel approach is developed t...... representations enabled participants in project-based design to develop and share understanding. The complexity of projects and their distributed and mediated nature makes this approach timely and important in addressing new research questions and practical challenges.......Project-based design involves a variety of visual representations, which are evolved to make decisions and accomplish project objectives. Yet, such mediated and distributed ways of working are difficult to capture through ethnographies that examine situated design. A novel approach is developed...... of situated design. This allows the researcher to be nimble, tracing connections across complex engineering projects; reconstructing practices through their visual representations; and observing their effects. Second, it articulates how, in these empirical cases, interaction with a cascade of visual...

  9. Receptor-based 3D-QSAR in Drug Design: Methods and Applications in Kinase Studies.

    Science.gov (United States)

    Fang, Cheng; Xiao, Zhiyan

    2016-01-01

    Receptor-based 3D-QSAR strategy represents a superior integration of structure-based drug design (SBDD) and three-dimensional quantitative structure-activity relationship (3D-QSAR) analysis. It combines the accurate prediction of ligand poses by the SBDD approach with the good predictability and interpretability of statistical models derived from the 3D-QSAR approach. Extensive efforts have been devoted to the development of receptor-based 3D-QSAR methods and two alternative approaches have been exploited. One associates with computing the binding interactions between a receptor and a ligand to generate structure-based descriptors for QSAR analyses. The other concerns the application of various docking protocols to generate optimal ligand poses so as to provide reliable molecular alignments for the conventional 3D-QSAR operations. This review highlights new concepts and methodologies recently developed in the field of receptorbased 3D-QSAR, and in particular, covers its application in kinase studies.

  10. Rationale for reduced tornado design bases

    International Nuclear Information System (INIS)

    Rutherford, P.D.; Ho, H.W.; Hartung, J.A.; Kastenberg, W.E.

    1985-01-01

    This paper provides a rationale for relaxing the present NRC tornado design requirements, which are based on a design basis tornado (DBT) whose frequency of exceedance is 10 -7 per year. It is proposed that a reduced DBT frequency of 10 -5 to 10 -6 per year is acceptable. This change in the tornado design bases for LMFBRs (and possibly all types of nuclear plants) is justified based on (1) existing NRC regulations and guidelines, (2) probabilistic arguments, (3) consistency with NRC trial safety goals, and (4) cost-benefit analysis

  11. Conceptual design for the breakwater system of the south of Doson naval base : Optimisation versus deterministic design

    NARCIS (Netherlands)

    Viet, N.D.; Verhagen, H.J.; Van Gelder, P.H.A.J.M.; Vrijling, J.K.

    2008-01-01

    In 2006 a Vietnamese Engineering Consultancy Company carried out a design study of a Naval Base at the location of the South of Doson Peninsula in Vietnam. A deterministic approach applied to the conceptual design of the breakwater system of the Naval Base resulted in a cross-section with a big

  12. User Experience Design in Professional Map-Based Geo-Portals

    Directory of Open Access Journals (Sweden)

    Bastian Zimmer

    2013-10-01

    Full Text Available We have recently been witnessing the growing establishment of map-centered web-based geo-portals on national, regional and local levels. However, a particular issue with these geo-portals is that each instance has been implemented in different ways in terms of design, usability, functionality, interaction possibilities, map size and symbologies. In this paper, we try to tackle these shortcomings by analyzing and formalizing the requirements for map-based geo-portals in a user experience based approach. First, we propose a holistic definition the term of a “geo-portal”. Then, we present our approach to user experience design for map-based geo-portals by defining the functional requirements of a geo-portal, by analyzing previous geo-portal developments, by distilling the results of our empirical user study to perform practically-oriented user requirements, and finally by establishing a set of user experience design guidelines for the creation of map-based geo-portals. These design guidelines have been extracted for each of the main components of a geo-portal, i.e., the map, the search dialogue, the presentation of the search results, symbologies, and other aspects. These guidelines shall constitute the basis for future geo-portal developments to achieve standardization in the user-experience design of map-based geo-portals.

  13. Design of a community-based intergenerational oral health study: ?Baby Smiles?

    OpenAIRE

    Milgrom, Peter; Riedy, Christine A; Weinstein, Philip; Mancl, Lloyd A; Garson, Gayle; Huebner, Colleen E; Smolen, Darlene; Sutherland, Marilynn

    2013-01-01

    Background Rural, low-income pregnant women and their children are at high risk for poor oral health and have low utilization rates of dental care. The Baby Smiles study was designed to increase low-income pregnant women?s utilization of dental care, increase young children?s dental care utilization, and improve home oral health care practices. Methods/design Baby Smiles was a five-year, four-site randomized intervention trial with a 2 ? 2 factorial design. Four hundred participants were rand...

  14. Model based process-product design and analysis

    DEFF Research Database (Denmark)

    Gani, Rafiqul

    This paper gives a perspective on modelling and the important role it has within product-process design and analysis. Different modelling issues related to development and application of systematic model-based solution approaches for product-process design is discussed and the need for a hybrid...... model-based framework is highlighted. This framework should be able to manage knowledge-data, models, and associated methods and tools integrated with design work-flows and data-flows for specific product-process design problems. In particular, the framework needs to manage models of different types......, forms and complexity, together with their associated parameters. An example of a model-based system for design of chemicals based formulated products is also given....

  15. Target based drug design - a reality in virtual sphere.

    Science.gov (United States)

    Verma, Saroj; Prabhakar, Yenamandra S

    2015-01-01

    The target based drug design approaches are a series of computational procedures, including visualization tools, to support the decision systems of drug design/discovery process. In the essence of biological targets shaping the potential lead/drug molecules, this review presents a comprehensive position of different components of target based drug design which include target identification, protein modeling, molecular dynamics simulations, binding/catalytic sites identification, docking, virtual screening, fragment based strategies, substructure treatment of targets in tackling drug resistance, in silico ADMET, structural vaccinology, etc along with the key issues involved therein and some well investigated case studies. The concepts and working of these procedures are critically discussed to arouse interest and to advance the drug research.

  16. The networked student: A design-based research case study of student constructed personal learning environments in a middle school science course

    Science.gov (United States)

    Drexler, Wendy

    This design-based research case study applied a networked learning approach to a seventh grade science class at a public school in the southeastern United States. Students adapted emerging Web applications to construct personal learning environments for in-depth scientific inquiry of poisonous and venomous life forms. The personal learning environments constructed used Application Programming Interface (API) widgets to access, organize, and synthesize content from a number of educational Internet resources and social network connections. This study examined the nature of personal learning environments; the processes students go through during construction, and patterns that emerged. The project was documented from both an instructional and student-design perspective. Findings revealed that students applied the processes of: practicing digital responsibility; practicing digital literacy; organizing content; collaborating and socializing; and synthesizing and creating. These processes informed a model of the networked student that will serve as a framework for future instructional designs. A networked learning approach that incorporates these processes into future designs has implications for student learning, teacher roles, professional development, administrative policies, and delivery. This work is significant in that it shifts the focus from technology innovations based on tools to student empowerment based on the processes required to support learning. It affirms the need for greater attention to digital literacy and responsibility in K12 schools as well as consideration for those skills students will need to achieve success in the 21st century. The design-based research case study provides a set of design principles for teachers to follow when facilitating student construction of personal learning environments.

  17. Three-dimensional design methodologies for tree-based FPGA architecture

    CERN Document Server

    Pangracious, Vinod; Mehrez, Habib

    2015-01-01

    This book focuses on the development of 3D design and implementation methodologies for Tree-based FPGA architecture. It also stresses the needs for new and augmented 3D CAD tools to support designs such as, the design for 3D, to manufacture high performance 3D integrated circuits and reconfigurable FPGA-based systems. This book was written as a text that covers the foundations of 3D integrated system design and FPGA architecture design. It was written for the use in an elective or core course at the graduate level in field of Electrical Engineering, Computer Engineering and Doctoral Research programs. No previous background on 3D integration is required, nevertheless fundamental understanding of 2D CMOS VLSI design is required. It is assumed that reader has taken the core curriculum in Electrical Engineering or Computer Engineering, with courses like CMOS VLSI design, Digital System Design and Microelectronics Circuits being the most important. It is accessible for self-study by both senior students and profe...

  18. Conceptual design study of Fusion Experimental Reactor (FY87FER)

    International Nuclear Information System (INIS)

    Miki, Nobuharu; Iida, Fumio; Wachi, Yoshihiro; Toyoda, Katsuyoshi; Hashizume, Takashi; Konno, Masayuki.

    1988-06-01

    This report describes the FER magnet design which was conducted last year (1987). Based on a large uncertainty of the physics assumption, two sets of FER concepts have been developed. One is based on the best existing physics data bases and another is based on rather conservative physics bases. In the magnet design, the improvements of superconducting magnet design were investigated to reduce the reactor size and to realize higher reactor-core performance. In addition, we studied several critical technical issues that affect the magnet design specification. (author)

  19. Liaison based assembly design

    Energy Technology Data Exchange (ETDEWEB)

    Ames, A.; Kholwadwala, D.; Wilson, R.H.

    1996-12-01

    Liaison Based Assembly Design extends the current information infrastructure to support design in terms of kinematic relationships between parts, or liaisons. These liaisons capture information regarding contact, degrees-of-freedom constraints and containment relationships between parts in an assembly. The project involved defining a useful collection of liaison representations, investigating their properties, and providing for maximum use of the data in downstream applications. We tested our ideas by implementing a prototype system involving extensions to Pro/Engineer and the Archimedes assembly planner. With an expanded product model, the design system is more able to capture design intent. When a product update is attempted, increased knowledge availability improves our ability to understand the effect of design changes. Manufacturing and analysis disciplines benefit from having liaison information available, so less time is wasted arguing over incomplete design specifications and our enterprise can be more completely integrated.

  20. Overstrength of Displacement-Based Designed Eccentrically Braced Steel Frames

    Directory of Open Access Journals (Sweden)

    Sina Farahani

    2016-03-01

    Full Text Available Direct Displacement-Based Design (DDBD is a performance-based seismic design method that has been proposed and developed over the past two decades for RC frame structures, shear walls and bridges design. The aim of this study is to evaluate overstrength of EBFs with short, intermediate and long link beams designed according to the DDBD method. For this purpose, twelve EBFs with 3, 5, 9 and 12 stories having short, intermediate and long link beams designed using the DDBD method. To investigate the seismic behavior of the considered EBFs, it is first necessary to model properly the nonlinear cyclic behavior of link beams properly. In this regard, the macro-model developed and proposed by Richards was utilized in this study to simulate the nonlinear behavior of some tested link beams available in the literature. After validating the finite-element model, the seismic behavior of the considered EBFs was studied using nonlinear static analyses. The results show that the overstrength factors of the DDB designed EBFs are variable depending on their links length ratio and may even be less than the factor proposed in the DDBD method (i.e. 1.5. This factor was evaluated as 1.51, 1.37 and 1.19 for the investigated EBFs in this study with short, intermediate and long link beams, respectively.

  1. Building a Case-Based Design Assistant for Workplace Environment Design

    NARCIS (Netherlands)

    Mallory-Hill, S.M.; Timmermans, H.J.P.

    1998-01-01

    This paper reports on the early stages of development of a case-based design tool. The purpose of this tool, called the Workplace Environment Design Advisor (WEDA), is to support architects in the conceptual design of workplace environments. The objective of this system is to provide electronic

  2. [Saarland Growth Study: sampling design].

    Science.gov (United States)

    Danker-Hopfe, H; Zabransky, S

    2000-01-01

    The use of reference data to evaluate the physical development of children and adolescents is part of the daily routine in the paediatric ambulance. The construction of such reference data is based on the collection of extensive reference data. There are different kinds of reference data: cross sectional references, which are based on data collected from a big representative cross-sectional sample of the population, longitudinal references, which are based on follow-up surveys of usually smaller samples of individuals from birth to maturity, and mixed longitudinal references, which are a combination of longitudinal and cross-sectional reference data. The advantages and disadvantages of the different methods of data collection and the resulting reference data are discussed. The Saarland Growth Study was conducted for several reasons: growth processes are subject to secular changes, there are no specific reference data for children and adolescents from this part of the country and the growth charts in use in the paediatric praxis are possibly not appropriate any more. Therefore, the Saarland Growth Study served two purposes a) to create actual regional reference data and b) to create a database for future studies on secular trends in growth processes of children and adolescents from Saarland. The present contribution focusses on general remarks on the sampling design of (cross-sectional) growth surveys and its inferences for the design of the present study.

  3. Novel study guides for biochemistry meaningful learning in biology: a design-based research

    Directory of Open Access Journals (Sweden)

    Caetano da Costa

    2017-12-01

    Full Text Available To address the usually decontextualized transmission of information in biochemistry teaching, three interventions in a discipline (Metabolism for Biology majors were applied as innovative study guides. We describe the development, application, and evaluation of two study guides, contextualized with a real problem or an integrative view, using broad themes like evolution and metabolic adaptation. In order to evaluate the impact of both interventions on interest, motivation, and learning of the metabolic pathways, a design-based research with cycles of application and assessment was carried out, by means of classroom observation, grade analysis in written exams, and students’ interviews. Analysis and interpretation of the results point to benefits for teaching and learning, with helpful information to guide elaboration and refinement of new teaching materials and to make active learning more meaningful.

  4. A Novel Simulation Technician Laboratory Design: Results of a Survey-Based Study.

    Science.gov (United States)

    Ahmed, Rami; Hughes, Patrick G; Friedl, Ed; Ortiz Figueroa, Fabiana; Cepeda Brito, Jose R; Frey, Jennifer; Birmingham, Lauren E; Atkinson, Steven Scott

    2016-03-16

    OBJECTIVE : The purpose of this study was to elicit feedback from simulation technicians prior to developing the first simulation technician-specific simulation laboratory in Akron, OH. Simulation technicians serve a vital role in simulation centers within hospitals/health centers around the world. The first simulation technician degree program in the US has been approved in Akron, OH. To satisfy the requirements of this program and to meet the needs of this special audience of learners, a customized simulation lab is essential. A web-based survey was circulated to simulation technicians prior to completion of the lab for the new program. The survey consisted of questions aimed at identifying structural and functional design elements of a novel simulation center for the training of simulation technicians. Quantitative methods were utilized to analyze data. Over 90% of technicians (n=65) think that a lab designed explicitly for the training of technicians is novel and beneficial. Approximately 75% of respondents think that the space provided appropriate audiovisual (AV) infrastructure and space to evaluate the ability of technicians to be independent. The respondents think that the lab needed more storage space, visualization space for a large number of students, and more space in the technical/repair area. CONCLUSIONS : A space designed for the training of simulation technicians was considered to be beneficial. This laboratory requires distinct space for technical repair, adequate bench space for the maintenance and repair of simulators, an appropriate AV infrastructure, and space to evaluate the ability of technicians to be independent.

  5. Making Design Decisions Visible: Applying the Case-Based Method in Designing Online Instruction

    Directory of Open Access Journals (Sweden)

    Heng Luo,

    2011-01-01

    Full Text Available The instructional intervention in this design case is a self-directed online tutorial that applies the case-based method to teach educators how to design and conduct entrepreneurship programs for elementary school students. In this article, the authors describe the major decisions made in each phase of the design and development process, explicate the rationales behind them, and demonstrate their effect on the production of the tutorial. Based on such analysis, the guidelines for designing case-based online instruction are summarized for the design case.

  6. Design bases - Concrete structures

    International Nuclear Information System (INIS)

    Diaz-Llanos Ros, M.

    1993-01-01

    The most suitable title for Section 2 is 'Design Bases', which covers not only calculation but also the following areas: - Structural design concepts. - Project criteria. - Material specifications. These concepts are developed in more detail in the following sections. The numbering in this document is neither complete nor hierarchical since, for easier cross referencing, it corresponds to the paragraphs of Eurocode 2 Part 1 (hereinafter 'EUR-2') which are commented on. (author)

  7. Web-Based Intervention for Women With Type 1 Diabetes in Pregnancy and Early Motherhood: Critical Analysis of Adherence to Technological Elements and Study Design.

    Science.gov (United States)

    Berg, Marie; Linden, Karolina; Adolfsson, Annsofie; Sparud Lundin, Carina; Ranerup, Agneta

    2018-05-02

    Numerous Web-based interventions have been implemented to promote health and health-related behaviors in persons with chronic conditions. Using randomized controlled trials to evaluate such interventions creates a range of challenges, which in turn can influence the study outcome. Applying a critical perspective when evaluating Web-based health interventions is important. The objective of this study was to critically analyze and discuss the challenges of conducting a Web-based health intervention as a randomized controlled trial. The MODIAB-Web study was critically examined using an exploratory case study methodology and the framework for analysis offered through the Persuasive Systems Design model. Focus was on technology, study design, and Web-based support usage, with special focus on the forum for peer support. Descriptive statistics and qualitative content analysis were used. The persuasive content and technological elements in the design of the randomized controlled trial included all four categories of the Persuasive Systems Design model, but not all design principles were implemented. The study duration was extended to a period of four and a half years. Of 81 active participants in the intervention group, a maximum of 36 women were simultaneously active. User adherence varied greatly with a median of 91 individual log-ins. The forum for peer support was used by 63 participants. Although only about one-third of the participants interacted in the forum, there was a fairly rich exchange of experiences and advice between them. Thus, adherence in terms of social interactions was negatively affected by limited active participation due to prolonged recruitment process and randomization effects. Lessons learned from this critical analysis are that technology and study design matter and might mutually influence each other. In Web-based interventions, the use of design theories enables utilization of the full potential of technology and promotes adherence. The

  8. Design of Object-based Information System Prototype

    OpenAIRE

    Suhyeon Yoo; Sumi Shin; Hyesun Kim

    2014-01-01

    Researchers who use science and technology information were found to ask an information service in which they can excerpt the contents they needed, rather than using the information at article level. In this study, we micronized the contents of scholarly articles into text, image, and table and then constructed a micro-content DB to design a new information system prototype based on this micro-content. After designing the prototype, we performed usability test for this prototype so as to conf...

  9. Scenario-based design: a method for connecting information system design with public health operations and emergency management.

    Science.gov (United States)

    Reeder, Blaine; Turner, Anne M

    2011-12-01

    Responding to public health emergencies requires rapid and accurate assessment of workforce availability under adverse and changing circumstances. However, public health information systems to support resource management during both routine and emergency operations are currently lacking. We applied scenario-based design as an approach to engage public health practitioners in the creation and validation of an information design to support routine and emergency public health activities. Using semi-structured interviews we identified the information needs and activities of senior public health managers of a large municipal health department during routine and emergency operations. Interview analysis identified 25 information needs for public health operations management. The identified information needs were used in conjunction with scenario-based design to create 25 scenarios of use and a public health manager persona. Scenarios of use and persona were validated and modified based on follow-up surveys with study participants. Scenarios were used to test and gain feedback on a pilot information system. The method of scenario-based design was applied to represent the resource management needs of senior-level public health managers under routine and disaster settings. Scenario-based design can be a useful tool for engaging public health practitioners in the design process and to validate an information system design. Copyright © 2011 Elsevier Inc. All rights reserved.

  10. Controlled air incinerator conceptual design study

    International Nuclear Information System (INIS)

    1982-01-01

    This report presents a conceptual design study for a controlled air incinerator facility for incineration of low level combustible waste at Three Mile Island Unit 2 (TMI-2). The facility design is based on the use of a Helix Process Systems controlled air incinerator. Cost estimates and associated engineering, procurement, and construction schedules are also provided. The cost estimates and schedules are presented for two incinerator facility designs, one with provisions for waste ash solidification, the other with provisions for packaging the waste ash for transport to an undefined location

  11. Performance-based Pareto optimal design

    NARCIS (Netherlands)

    Sariyildiz, I.S.; Bittermann, M.S.; Ciftcioglu, O.

    2008-01-01

    A novel approach for performance-based design is presented, where Pareto optimality is pursued. Design requirements may contain linguistic information, which is difficult to bring into computation or make consistent their impartial estimations from case to case. Fuzzy logic and soft computing are

  12. Verification of product design using regulation knowledge base and Web services

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ik June [KAERI, Daejeon (Korea, Republic of); Lee, Jae Chul; Mun Du Hwan [Kyungpook National University, Daegu (Korea, Republic of); Kim, Byung Chul [Dong-A University, Busan (Korea, Republic of); Hwang, Jin Sang [PartDB Co., Ltd., Daejeom (Korea, Republic of); Lim, Chae Ho [Korea Institute of Industrial Technology, Incheon (Korea, Republic of)

    2015-11-15

    Since product regulations contain important rules or codes that manufacturers must follow, automatic verification of product design with the regulations related to a product is necessary. For this, this study presents a new method for the verification of product design using regulation knowledge base and Web services. Regulation knowledge base consisting of product ontology and rules was built with a hybrid technique combining ontology and programming languages. Web service for design verification was developed ensuring the flexible extension of knowledge base. By virtue of two technical features, design verification is served to various products while the change of system architecture is minimized.

  13. Verification of product design using regulation knowledge base and Web services

    International Nuclear Information System (INIS)

    Kim, Ik June; Lee, Jae Chul; Mun Du Hwan; Kim, Byung Chul; Hwang, Jin Sang; Lim, Chae Ho

    2015-01-01

    Since product regulations contain important rules or codes that manufacturers must follow, automatic verification of product design with the regulations related to a product is necessary. For this, this study presents a new method for the verification of product design using regulation knowledge base and Web services. Regulation knowledge base consisting of product ontology and rules was built with a hybrid technique combining ontology and programming languages. Web service for design verification was developed ensuring the flexible extension of knowledge base. By virtue of two technical features, design verification is served to various products while the change of system architecture is minimized.

  14. Consequence Based Design. An approach for integrating computational collaborative models (Integrated Dynamic Models) in the building design phase

    DEFF Research Database (Denmark)

    Negendahl, Kristoffer

    relies on various advancements in the area of integrated dynamic models. It also relies on the application and test of the approach in practice to evaluate the Consequence based design and the use of integrated dynamic models. As a result, the Consequence based design approach has been applied in five...... and define new ways to implement integrated dynamic models for the following project. In parallel, seven different developments of new methods, tools and algorithms have been performed to support the application of the approach. The developments concern: Decision diagrams – to clarify goals and the ability...... affect the design process and collaboration between building designers and simulationists. Within the limits of applying the approach of Consequence based design to five case studies, followed by documentation based on interviews, surveys and project related documentations derived from internal reports...

  15. Optimum study designs.

    Science.gov (United States)

    Gu, C; Rao, D C

    2001-01-01

    Because simplistic designs will lead to prohibitively large sample sizes, the optimization of genetic study designs is critical for successfully mapping genes for complex diseases. Creative designs are necessary for detecting and amplifying the usually weak signals for complex traits. Two important outcomes of a study design--power and resolution--are implicitly tied together by the principle of uncertainty. Overemphasis on either one may lead to suboptimal designs. To achieve optimality for a particular study, therefore, practical measures such as cost-effectiveness must be used to strike a balance between power and resolution. In this light, the myriad of factors involved in study design can be checked for their effects on the ultimate outcomes, and the popular existing designs can be sorted into building blocks that may be useful for particular situations. It is hoped that imaginative construction of novel designs using such building blocks will lead to enhanced efficiency in finding genes for complex human traits.

  16. A Framework for IT-based Design Tools

    DEFF Research Database (Denmark)

    Hartvig, Susanne C

    The thesis presents a new apprach to develop design tools that can be integrated, bypresenting a framework consisting of a set of guidelines for design tools, an integration andcommunication scheme, and a set of design tool schemes.This framework has been based onanalysis of requirements to integ...... to integrated design enviornments, and analysis of engineeringdesign and design problem solving methods. And the developed framework has been testedby applying it to development of prototype design tools for realistic design scenarios.......The thesis presents a new apprach to develop design tools that can be integrated, bypresenting a framework consisting of a set of guidelines for design tools, an integration andcommunication scheme, and a set of design tool schemes.This framework has been based onanalysis of requirements...

  17. Food Enterprise Web Design Based on User Experience

    OpenAIRE

    Fei Wang

    2015-01-01

    Excellent auxiliary food enterprise web design conveyed good visual transmission effect through user experience. This study was based on the food enterprise managers and customers as the main operating object to get the performance of the web page creation, web page design not only focused on the function and work efficiency, the most important thing was that the user experience in the process of web page interaction.

  18. The impact of design-based modeling instruction on seventh graders' spatial abilities and model-based argumentation

    Science.gov (United States)

    McConnell, William J.

    Due to the call of current science education reform for the integration of engineering practices within science classrooms, design-based instruction is receiving much attention in science education literature. Although some aspect of modeling is often included in well-known design-based instructional methods, it is not always a primary focus. The purpose of this study was to better understand how design-based instruction with an emphasis on scientific modeling might impact students' spatial abilities and their model-based argumentation abilities. In the following mixed-method multiple case study, seven seventh grade students attending a secular private school in the Mid-Atlantic region of the United States underwent an instructional intervention involving design-based instruction, modeling and argumentation. Through the course of a lesson involving students in exploring the interrelatedness of the environment and an animal's form and function, students created and used multiple forms of expressed models to assist them in model-based scientific argument. Pre/post data were collected through the use of The Purdue Spatial Visualization Test: Rotation, the Mental Rotation Test and interviews. Other data included a spatial activities survey, student artifacts in the form of models, notes, exit tickets, and video recordings of students throughout the intervention. Spatial abilities tests were analyzed using descriptive statistics while students' arguments were analyzed using the Instrument for the Analysis of Scientific Curricular Arguments and a behavior protocol. Models were analyzed using content analysis and interviews and all other data were coded and analyzed for emergent themes. Findings in the area of spatial abilities included increases in spatial reasoning for six out of seven participants, and an immense difference in the spatial challenges encountered by students when using CAD software instead of paper drawings to create models. Students perceived 3D printed

  19. A model-based meta-analysis of monoclonal antibody pharmacokinetics to guide optimal first-in-human study design

    Science.gov (United States)

    Davda, Jasmine P; Dodds, Michael G; Gibbs, Megan A; Wisdom, Wendy; Gibbs, John P

    2014-01-01

    The objectives of this retrospective analysis were (1) to characterize the population pharmacokinetics (popPK) of four different monoclonal antibodies (mAbs) in a combined analysis of individual data collected during first-in-human (FIH) studies and (2) to provide a scientific rationale for prospective design of FIH studies with mAbs. The data set was composed of 171 subjects contributing a total of 2716 mAb serum concentrations, following intravenous (IV) and subcutaneous (SC) doses. mAb PK was described by an open 2-compartment model with first-order elimination from the central compartment and a depot compartment with first-order absorption. Parameter values obtained from the popPK model were further used to generate optimal sampling times for a single dose study. A robust fit to the combined data from four mAbs was obtained using the 2-compartment model. Population parameter estimates for systemic clearance and central volume of distribution were 0.20 L/day and 3.6 L with intersubject variability of 31% and 34%, respectively. The random residual error was 14%. Differences (> 2-fold) in PK parameters were not apparent across mAbs. Rich designs (22 samples/subject), minimal designs for popPK (5 samples/subject), and optimal designs for non-compartmental analysis (NCA) and popPK (10 samples/subject) were examined by stochastic simulation and estimation. Single-dose PK studies for linear mAbs executed using the optimal designs are expected to yield high-quality model estimates, and accurate capture of NCA estimations. This model-based meta-analysis has determined typical popPK values for four mAbs with linear elimination and enabled prospective optimization of FIH study designs, potentially improving the efficiency of FIH studies for this class of therapeutics. PMID:24837591

  20. On the analysis of genome-wide association studies in family-based designs: a universal, robust analysis approach and an application to four genome-wide association studies.

    Directory of Open Access Journals (Sweden)

    Sungho Won

    2009-11-01

    Full Text Available For genome-wide association studies in family-based designs, we propose a new, universally applicable approach. The new test statistic exploits all available information about the association, while, by virtue of its design, it maintains the same robustness against population admixture as traditional family-based approaches that are based exclusively on the within-family information. The approach is suitable for the analysis of almost any trait type, e.g. binary, continuous, time-to-onset, multivariate, etc., and combinations of those. We use simulation studies to verify all theoretically derived properties of the approach, estimate its power, and compare it with other standard approaches. We illustrate the practical implications of the new analysis method by an application to a lung-function phenotype, forced expiratory volume in one second (FEV1 in 4 genome-wide association studies.

  1. SP-100 power system conceptual design for lunar base applications

    International Nuclear Information System (INIS)

    Mason, L.S.; Bloomfield, H.S.; Hainley, D.C.

    1989-01-01

    A conceptual design is presented for a nuclear power system utilizing an SP-100 reactor and multiple Stirling cycle engines for operation on the lunar surface. Based on the results of this study, it was concluded that this power plant could be a viable option for an evolutionary lunar base. The design concept consists of a 2500 kWt (kilowatt thermal) SP-100 reactor coupled to eight free-piston Stirling engines. Two of the engines are held in reserve to provide conversion system redundancy. The remaining engines operate at 91.7 percent of their rated capacity of 150 kWe. The design power level for this system is 825 kWe. Each engine has a pumped heat-rejection loop connected to a heat pipe radiator. Power system performance, sizing, layout configurations, shielding options, and transmission line characteristics are described. System components and integration options are compared for safety, high performance, low mass, and ease of assembly. The power plant was integrated with a proposed human lunar base concept to ensure mission compatibility. This study should be considered a preliminary investigation; further studies are planned to investigate the effect of different technologies on this baseline design

  2. Discovery and design of carbohydrate-based therapeutics.

    Science.gov (United States)

    Cipolla, Laura; Araújo, Ana C; Bini, Davide; Gabrielli, Luca; Russo, Laura; Shaikh, Nasrin

    2010-08-01

    Till now, the importance of carbohydrates has been underscored, if compared with the two other major classes of biopolymers such as oligonucleotides and proteins. Recent advances in glycobiology and glycochemistry have imparted a strong interest in the study of this enormous family of biomolecules. Carbohydrates have been shown to be implicated in recognition processes, such as cell-cell adhesion, cell-extracellular matrix adhesion and cell-intruder recognition phenomena. In addition, carbohydrates are recognized as differentiation markers and as antigenic determinants. Due to their relevant biological role, carbohydrates are promising candidates for drug design and disease treatment. However, the growing number of human disorders known as congenital disorders of glycosylation that are being identified as resulting from abnormalities in glycan structures and protein glycosylation strongly indicates that a fast development of glycobiology, glycochemistry and glycomedicine is highly desirable. The topics give an overview of different approaches that have been used to date for the design of carbohydrate-based therapeutics; this includes the use of native synthetic carbohydrates, the use of carbohydrate mimics designed on the basis of their native counterpart, the use of carbohydrates as scaffolds and finally the design of glyco-fused therapeutics, one of the most recent approaches. The review covers mainly literature that has appeared since 2000, except for a few papers cited for historical reasons. The reader will gain an overview of the current strategies applied to the design of carbohydrate-based therapeutics; in particular, the advantages/disadvantages of different approaches are highlighted. The topic is presented in a general, basic manner and will hopefully be a useful resource for all readers who are not familiar with it. In addition, in order to stress the potentialities of carbohydrates, several examples of carbohydrate-based marketed therapeutics are given

  3. Bodystorming for Movement-Based Interaction Design

    Directory of Open Access Journals (Sweden)

    Elena Márquez Segura

    2016-11-01

    Full Text Available After a decade of movement-based interaction in human–computer interaction, designing for the moving body still remains a challenge. Research in this field requires methods to help access, articulate, and harness embodied experiences in ways that can inform the design process. To address this challenge, this article appropriates bodystorming, an embodied ideation method for movement-based interaction design. The proposed method allows for early consideration of the physical, collocated, and social aspects of a designed activity as illustrated with two explorative workshops in different application domains: interactive body games and interactive performances. Using a qualitative methods approach, we used video material from the workshops, feedback from participants, and our own experience as participants and facilitators to outline important characteristics of the bodystorming method in the domain of movement-based interaction. The proposed method is compared with previous ones and application implications are discussed.

  4. Design-based research in designing the model for educating simulation facilitators.

    Science.gov (United States)

    Koivisto, Jaana-Maija; Hannula, Leena; Bøje, Rikke Buus; Prescott, Stephen; Bland, Andrew; Rekola, Leena; Haho, Päivi

    2018-03-01

    The purpose of this article is to introduce the concept of design-based research, its appropriateness in creating education-based models, and to describe the process of developing such a model. The model was designed as part of the Nurse Educator Simulation based learning project, funded by the EU's Lifelong Learning program (2013-1-DK1-LEO05-07053). The project partners were VIA University College, Denmark, the University of Huddersfield, UK and Metropolia University of Applied Sciences, Finland. As an outcome of the development process, "the NESTLED model for educating simulation facilitators" (NESTLED model) was generated. This article also illustrates five design principles that could be applied to other pedagogies. Copyright © 2018 Elsevier Ltd. All rights reserved.

  5. Adaptive Observer-Based Fault-Tolerant Control Design for Uncertain Systems

    Directory of Open Access Journals (Sweden)

    Huaming Qian

    2015-01-01

    Full Text Available This study focuses on the design of the robust fault-tolerant control (FTC system based on adaptive observer for uncertain linear time invariant (LTI systems. In order to improve robustness, rapidity, and accuracy of traditional fault estimation algorithm, an adaptive fault estimation algorithm (AFEA using an augmented observer is presented. By utilizing a new fault estimator model, an improved AFEA based on linear matrix inequality (LMI technique is proposed to increase the performance. Furthermore, an observer-based state feedback fault-tolerant control strategy is designed, which guarantees the stability and performance of the faulty system. Moreover, the adaptive observer and the fault-tolerant controller are designed separately, whose performance can be considered, respectively. Finally, simulation results of an aircraft application are presented to illustrate the effectiveness of the proposed design methods.

  6. Development of a Web-Based Health Care Intervention for Patients With Heart Disease: Lessons Learned From a Participatory Design Study.

    Science.gov (United States)

    Noergaard, Birgitte; Sandvei, Marianne; Rottmann, Nina; Johannessen, Helle; Wiil, Uffe; Schmidt, Thomas; Pedersen, Susanne S

    2017-05-17

    The use of telemedicine technologies in health care has increased substantially, together with a growing interest in participatory design methods when developing telemedicine approaches. We present lessons learned from a case study involving patients with heart disease and health care professionals in the development of a personalized Web-based health care intervention. We used a participatory design approach inspired by the method for feasibility studies in software development. We collected qualitative data using multiple methods in 3 workshops and analyzed the data using thematic analysis. Participants were 7 patients with diagnosis of heart disease, 2 nurses, 1 physician, 2 systems architects, 3 moderators, and 3 observers. We present findings in 2 parts. (1) Outcomes of the participatory design process: users gave valuable feedback on ease of use of the platforms' tracking tools, platform design, terminology, and insights into patients' monitoring needs, information and communication technologies skills, and preferences for self-management tools. (2) Experiences from the participatory design process: patients and health care professionals contributed different perspectives, with the patients using an experience-based approach and the health care professionals using a more attitude-based approach. The essential lessons learned concern planning and organization of workshops, including the finding that patients engaged actively and willingly in a participatory design process, whereas it was more challenging to include and engage health care professionals. ©Birgitte Noergaard, Marianne Sandvei, Nina Rottmann, Helle Johannessen, Uffe Wiil, Thomas Schmidt, Susanne S Pedersen. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 17.05.2017.

  7. Workplace building design and office-based workers' activity: a study of a natural experiment.

    Science.gov (United States)

    Jancey, Jonine M; McGann, Sarah; Creagh, Robyn; Blackford, Krysten D; Howat, Peter; Tye, Marian

    2016-02-01

    This opportunistic natural study investigated the effects of relocation of office workers from a 30-year-old building to a new purpose-built building. The new building included an attractive central staircase that was easily accessed and negotiated, as well as breakout spaces and a centralised facilities area. The researchers aimed to determine the impact of the purpose-built office building on the office workers' sedentariness and level of physical activity. In 2013, a natural pre-post study was undertaken with office-based workers in their old conventional 1970s building and on relocating to a new purpose-built 'activity permissive' building. Objective movement data was measured using accelerometers. Anthropometric and demographic data was also collected. Forty-two office-based workers significantly decreased their percentage of daily sitting time (T1 = 84.9% to T2=79.7%; pbuilding. Moderate activity significantly declined (T1=3.9% to 3.2%=T2; p=0.038). There was a significant decrease in mean minutes of sitting time (19.62 minutes; pbuilding can influence activity. This opportunistic study on the impact of workplace relocation on office-based workers' activity showed modest positive outcomes in sitting and standing. Evidence is required to inform building design policy and practice that supports physical activity and reduces levels of sedentariness in the workplace. © 2015 The Authors.

  8. The challenge of integrating evidence-based design.

    Science.gov (United States)

    Martin, Caren S

    2009-01-01

    This paper discusses the integration of evidence-based design (EBD) into the design process as an innovation, illuminates the significance and progress of the diffusion of this innovation, and identifies EBD advocates and the consequences of meeting the EBD challenge. A free tool for engaging in EBD is explored. Healthcare designers are leading the EBD charge, because their clients depend on it. But not all designers engage in EBD, because it may be beyond the resources of a firm or outside its culture. However, as with other meaningful design innovations, designers who do not practice EBD could fall by the wayside. EBD is a product of the diffusion of the innovation of evidence-based medicine. The academy (i.e., the collective of institutions of higher education), design organizations, design communities, and the media all contribute to the diffusion of EBD. However, the quantity, quality, and understandability of evidence continue to challenge its broad adoption. InformeDesign®, a free, Internet-based tool, presents information to designers in a concise, understandable way. Firms must invest in EBD incrementally as a value-added component of design to meet current and future challenges. It is important for designers to realize that engaging in EBD is not a rejection of creativity, but a means by which to elevate their design solutions. ©2009 VENDOME GROUP, LLC

  9. Developing Pedagogical Practices for English-Language Learners: A Design-Based Approach

    Science.gov (United States)

    Iddings, Ana Christina DaSilva; Rose, Brian Christopher

    2012-01-01

    This study draws on the application of sociocultural theory to second-language learning and teaching to examine the impact of a design-based research approach on teacher development and literacy instruction to English-language learners (ELLs). Design-based research methodology was employed to derive theoretical suppositions relating to the process…

  10. Flight Path Recovery System (FPRS) design study

    International Nuclear Information System (INIS)

    1978-09-01

    The study contained herein presents a design for a Flight Path Recovery System (FPPS) for use in the NURE Program which will be more accurate than systems presently used, provide position location data in digital form suitable for automatic data processing, and provide for flight path recovery in a more economic and operationally suitable manner. The design is based upon the use of presently available hardware and technoloy, and presents little, it any, development risk. In addition, a Flight Test Plan designed to test the FPRS design concept is presented

  11. Flight Path Recovery System (FPRS) design study

    Energy Technology Data Exchange (ETDEWEB)

    1978-09-01

    The study contained herein presents a design for a Flight Path Recovery System (FPPS) for use in the NURE Program which will be more accurate than systems presently used, provide position location data in digital form suitable for automatic data processing, and provide for flight path recovery in a more economic and operationally suitable manner. The design is based upon the use of presently available hardware and technoloy, and presents little, it any, development risk. In addition, a Flight Test Plan designed to test the FPRS design concept is presented.

  12. Design, Implementation and Evaluation of School-Based Sexual Health Education in Sub-Saharan Africa: A Qualitative Study of Researchers' Perspectives

    Science.gov (United States)

    Sani, A. Sadiq; Abraham, Charles; Denford, Sarah; Mathews, Catherine

    2018-01-01

    This study investigated facilitators and challenges to designing, implementing and evaluating school-based sexual health education in sub-Saharan Africa, using interviews with intervention designers and researchers. At the pre-planning and planning stages, participants reported that facilitating factors included addressing the reproductive health…

  13. The population-based Barcelona-Asymptomatic Intracranial Atherosclerosis Study (ASIA: rationale and design

    Directory of Open Access Journals (Sweden)

    Pera Guillem

    2011-02-01

    Full Text Available Abstract Background Large-artery intracranial atherosclerosis may be the most frequent cause of ischemic stroke worldwide. Traditional approaches have attempted to target the disease when it is already symptomatic. However, early detection of intracranial atherosclerosis may allow therapeutic intervention while the disease is still asymptomatic. The prevalence and natural history of asymptomatic intracranial atherosclerosis in Caucasians remain unclear. The aims of the Barcelona-ASymptomatic Intracranial Atherosclerosis (ASIA study are (1 to determine the prevalence of ASIA in a moderate-high vascular risk population, (2 to study its prognostic impact on the risk of suffering future major ischemic events, and (3 to identify predictors of the development, progression and clinical expression of this condition. Methods/Design Cross-over and cohort, population-based study. A randomly selected representative sample of 1,503 subjects with a mild-moderate-high vascular risk (as defined by a REGICOR score ≥ 5% and with neither a history of cerebrovascular nor ischemic heart disease will be studied. At baseline, all individuals will undergo extracranial and transcranial Color-Coded Duplex (TCCD ultrasound examinations to detect presence and severity of extra and intracranial atherosclerosis. Intracranial stenoses will be assessed by magnetic resonance angiography (MRA. Clinical and demographic variables will be recorded and blood samples will be drawn to investigate clinical, biological and genetic factors associated with the presence of ASIA. A long-term clinical and sonographic follow-up will be conducted thereafter to identify predictors of disease progression and of incident vascular events. Discussion The Barcelona-ASIA is a population-based study aiming to evaluate the prevalence and clinical importance of asymptomatic intracranial large-artery atherosclerosis in Caucasians. The ASIA project may provide a unique scientific resource to better

  14. An Agent Based approach to design Serious Game

    Directory of Open Access Journals (Sweden)

    Manuel Gentile

    2014-06-01

    Full Text Available Serious games are designed to train and educate learners, opening up new learning approaches like exploratory learning and situated cognition.  Despite growing interest in these games, their design is still an artisan process.On the basis of experiences in designing computer simulation, this paper proposes an agent-based approach to guide the design process of a serious game. The proposed methodology allows the designer to strike the right equilibrium between educational effectiveness and entertainment, realism and complexity.The design of the PNPVillage game is used as a case study. The PNPVillage game aims to introduce and foster an entrepreneurial mindset among young students. It was implemented within the framework of the European project “I  can… I cannot… I go!” Rev.2

  15. Seismic design and performance of nuclear safety related RC structures based on new seismic design principle

    International Nuclear Information System (INIS)

    Murugan, R.; Sivathanu Pillai, C.; Chattopadhyaya, S.; Sundaramurthy, C.

    2011-01-01

    Full text: Seismic design of safety related Reinforced Concrete (RC) structures of Nuclear power plants (NPP) in India as per the present AERB codal procedures tries to ensure predominantly elastic behaviour under OBE so that the features of Nuclear Power Plant (NPP) necessary for continued safe operation are designed to remain functional and prevent accident (collapse) of NPP under SSE for which certain Structures, Systems and Components (SSCs) those are necessary to ensure the capability to shut down the reactor safely, are designed to remain functional. While the seismic design principles of non safety related structures as per Indian code (IS 1893-2002) are ensuring elastic behaviour under DBE and inelastic behaviour under MCE by utilizing ductility and energy dissipation capacity of the structure effectively. The design principle of AERB code is ensuring elastic behaviour under OBE and is not enlightening much inference about the overall structural behaviour under SSE (only ensuring the capability of certain SSCs required for safe shutdown of reactor). Various buildings and structures of Indian Nuclear power plant are classified from the basis of associated safety functions in a descending order in according with their roles in preventions and mitigation of an accident or support functions for prevention. This paper covers a comprehensive seismic analysis and design methodology based on the AERB codal provisions followed for safety related RC structure taking Diesel Generator Building of PFBR as a case study and study and investigates its performance under OBE and SSE by carrying out Non-linear static Pushover analysis. Based on the analysis, observed variations, recommendations are given for getting the desired performance level so as to implement performance based design in the future NPP design

  16. Nuclear component design ontology building based on ASME codes

    International Nuclear Information System (INIS)

    Bao Shiyi; Zhou Yu; He Shuyan

    2005-01-01

    The adoption of ontology analysis in the study of concept knowledge acquisition and representation for the nuclear component design process based on computer-supported cooperative work (CSCW) makes it possible to share and reuse numerous concept knowledge of multi-disciplinary domains. A practical ontology building method is accordingly proposed based on Protege knowledge model in combination with both top-down and bottom-up approaches together with Formal Concept Analysis (FCA). FCA exhibits its advantages in the way it helps establish and improve taxonomic hierarchy of concepts and resolve concept conflict occurred in modeling multi-disciplinary domains. With Protege-3.0 as the ontology building tool, a nuclear component design ontology based ASME codes is developed by utilizing the ontology building method. The ontology serves as the basis to realize concept knowledge sharing and reusing of nuclear component design. (authors)

  17. Capturing the design bases on Palo Verde

    International Nuclear Information System (INIS)

    Rogers, A.C.; Prawlocki, F.C.

    1989-01-01

    Over the past several years, the nuclear power industry has been directing considerable attention to plant configuration control. Utilities have been put in difficult situations due to changes made in plants without full original design basis knowledge. Once a plant is constructed, there is often insufficient information from the reactor designer or the architect/engineer to properly support operations, especially changes to the plant. In many cases utilities do not know the design bases for their units. As a result of these concerns, many utilities have been searching for ways to define the appropriate design bases for their plant. This paper discusses steps taken by Palo Verde to produce a design bases document and how it is being used to support the operation of the three nuclear units

  18. Multimedia-Based Chip Design Education.

    Science.gov (United States)

    Catalkaya, Tamer; Golze, Ulrich

    This paper focuses on multimedia computer-based training programs on chip design. Their development must be fast and economical, in order to be affordable by technical university institutions. The self-produced teaching program Illusion, which demonstrates a monitor controller as an example of a small but complete chip design, was implemented to…

  19. Design and qualification of HPD based designs for safety systems

    International Nuclear Information System (INIS)

    Sharma, Mukesh Kr.; Chavan, Madhavi A.; Sawhney, Pratibha A.; Mohanty, Ashutos; John, Ajith K.; Ganesh, G.

    2014-01-01

    Field Programmable Gate Arrays (FPGA) and Complex Programmable Logic Devices (CPLD) are increasingly being used in C and I system of NPPs. The function of such an integrated circuit is not defined by the supplier of the physical component or micro-electronic technology but by the C and I designer. The hardware subsystems implemented in these devices typically use Hardware Description Language (HDL) like VHDL or Verilog to describe the functionality at the design entry level. These circuits are commonly known as 'HDL-Programmed Devices', (HPD). RCnD has developed a set of hardware boards to be used in next generation C and I systems. The boards have been designed based on present day technology and components. The intelligence of these boards has been implemented in HPDs (FPGA/CPLD) using VHDL. Since these boards are used in the safety and safety related systems, they have undergone a rigorous V and V process and qualification tests. This paper discusses the design attributes and qualification of these HPD based designs for nuclear class safety systems. (author)

  20. Mixture design procedure for flexible base.

    Science.gov (United States)

    2013-04-01

    This document provides information on mixture design requirements for a flexible base course. Sections : design requirements, job mix formula, contractor's responsibility, and engineer's responsibility. Tables : material requirements; requirements fo...

  1. Design study on sodium-cooled large-scale reactor

    International Nuclear Information System (INIS)

    Shimakawa, Yoshio; Nibe, Nobuaki; Hori, Toru

    2002-05-01

    In Phase 1 of the 'Feasibility Study on Commercialized Fast Reactor Cycle Systems (F/S)', an advanced loop type reactor has been selected as a promising concept of sodium-cooled large-scale reactor, which has a possibility to fulfill the design requirements of the F/S. In Phase 2 of the F/S, it is planed to precede a preliminary conceptual design of a sodium-cooled large-scale reactor based on the design of the advanced loop type reactor. Through the design study, it is intended to construct such a plant concept that can show its attraction and competitiveness as a commercialized reactor. This report summarizes the results of the design study on the sodium-cooled large-scale reactor performed in JFY2001, which is the first year of Phase 2. In the JFY2001 design study, a plant concept has been constructed based on the design of the advanced loop type reactor, and fundamental specifications of main systems and components have been set. Furthermore, critical subjects related to safety, structural integrity, thermal hydraulics, operability, maintainability and economy have been examined and evaluated. As a result of this study, the plant concept of the sodium-cooled large-scale reactor has been constructed, which has a prospect to satisfy the economic goal (construction cost: less than 200,000yens/kWe, etc.) and has a prospect to solve the critical subjects. From now on, reflecting the results of elemental experiments, the preliminary conceptual design of this plant will be preceded toward the selection for narrowing down candidate concepts at the end of Phase 2. (author)

  2. Virtual Reality Based Collaborative Design by Children with High-Functioning Autism: Design-Based Flexibility, Identity, and Norm Construction

    Science.gov (United States)

    Ke, Fengfeng; Lee, Sungwoong

    2016-01-01

    This exploratory case study examined the process and potential impact of collaborative architectural design and construction in an OpenSimulator-based virtual reality (VR) on the social skills development of children with high-functioning autism (HFA). Two children with a formal medical diagnosis of HFA and one typically developing peer, aged…

  3. Bridging operation and design. The encounter between practical and discipline-based knowledge in offshore platform design

    Energy Technology Data Exchange (ETDEWEB)

    Husemoen, Mette Suzanne

    1998-12-31

    This thesis investigates the relationship between operations and design and the design process, taking as case studies the two new platforms of Phillips Petroleum Company Norway on Ekofisk II, the Ekofisk 2/4 X drilling and wellhead platform and the Ekofisk 2/4 J processing and transportation platform. The emphasis has been on how to take into account operational experience in design. The two research questions are: (1) Are operations and design two communities-of-practice based on different kinds of knowledge?, and (2) What are the conditions for bridging knowledge in operations and design? From the theory reviewed and the field data presented the study concludes that physical closeness and integration of operations and design personnel, experience from the other community-of-practice, and mutual sympathy, trust, and respect, are important factors in bridging knowledge of the operations and design communities-of-practice and creating innovative solutions in design which transcend the existing knowledge in operations and design. 66 refs., 28 figs., 8 tabs.

  4. Bridging operation and design. The encounter between practical and discipline-based knowledge in offshore platform design

    Energy Technology Data Exchange (ETDEWEB)

    Husemoen, Mette Suzanne

    1997-12-31

    This thesis investigates the relationship between operations and design and the design process, taking as case studies the two new platforms of Phillips Petroleum Company Norway on Ekofisk II, the Ekofisk 2/4 X drilling and wellhead platform and the Ekofisk 2/4 J processing and transportation platform. The emphasis has been on how to take into account operational experience in design. The two research questions are: (1) Are operations and design two communities-of-practice based on different kinds of knowledge?, and (2) What are the conditions for bridging knowledge in operations and design? From the theory reviewed and the field data presented the study concludes that physical closeness and integration of operations and design personnel, experience from the other community-of-practice, and mutual sympathy, trust, and respect, are important factors in bridging knowledge of the operations and design communities-of-practice and creating innovative solutions in design which transcend the existing knowledge in operations and design. 66 refs., 28 figs., 8 tabs.

  5. Problem based Learning versus Design Thinking in Team based Project work

    DEFF Research Database (Denmark)

    Denise J. Stokholm, Marianne

    2014-01-01

    project based learning issues, which has caused a need to describe and compare the two models; in specific the understandings, approaches and organization of learning in project work. The PBL model viewing the process as 3 separate project stages including; problem analysis, problem solving and project......All educations at Aalborg University has since 1974 been rooted in Problem Based Learning (PBL). In 1999 a new education in Industrial design was set up, introducing Design Based Learning (DBL). Even though the two approaches have a lot in common they also hold different understandings of core...... report, with focus on problem solving through analysis. Design Based Learning viewing the process as series of integrated design spaces including; alignment, research, mission, vision, concept, product and process report, with focus on innovative ideation though integration. There is a need of renewing...

  6. A framework for AI-based nuclear design support system

    International Nuclear Information System (INIS)

    Furuta, Kazuo; Kondo, Shunsuke

    1991-01-01

    Nowadays many computer programs are being developed and used for the analytic tasks in nuclear reactor design, but experienced designers are still responsible for most of the synthetic tasks which are not amenable to algorithmic computer processes. Artificial intelligence (AI) is a promising technology to deal with these intractable tasks in design. In development of AI-based design support systems, it is desirable to choose a comprehensive framework based on the scientific theory of design. In this work a framework for AI-based design support systems for nuclear reactor design will be proposed based on an exploration model of design. The fundamental architectures of this framework will be described especially on knowledge representation, context management and design planning. (author)

  7. A systematic review of the use of an expertise-based randomised controlled trial design.

    Science.gov (United States)

    Cook, Jonathan A; Elders, Andrew; Boachie, Charles; Bassinga, Ted; Fraser, Cynthia; Altman, Doug G; Boutron, Isabelle; Ramsay, Craig R; MacLennan, Graeme S

    2015-05-30

    Under a conventional two-arm randomised trial design, participants are allocated to an intervention and participating health professionals are expected to deliver both interventions. However, health professionals often have differing levels of expertise in a skill-based interventions such as surgery or psychotherapy. An expertise-based approach to trial design, where health professionals only deliver an intervention in which they have expertise, has been proposed as an alternative. The aim of this project was to systematically review the use of an expertise-based trial design in the medical literature. We carried out a comprehensive search of nine databases--AMED, BIOSIS, CENTRAL, CINAHL, Cochrane Methodology Register, EMBASE, MEDLINE, Science Citation Index, and PsycINFO--from 1966 to 2012 and performed citation searches using the ISI Citation Indexes and Scopus. Studies that used an expertise-based trial design were included. Two review authors independently screened the titles and abstracts and assessed full-text reports. Data were extracted and summarised on the study characteristics, general and expertise-specific study methodology, and conduct. In total, 7476 titles and abstracts were identified, leading to 43 included studies (54 articles). The vast majority (88%) used a pure expertise-based design; three (7%) adopted a hybrid design, and two (5%) used a design that was unclear. Most studies compared substantially different interventions (79%). In many cases, key information relating to the expertise-based design was absent; only 12 (28%) reported criteria for delivering both interventions. Most studies recruited the target sample size or very close to it (median of 101, interquartile range of 94 to 118), although the target was reported for only 40% of studies. The proportion of participants who received the allocated intervention was high (92%, interquartile range of 82 to 99%). While use of an expertise-based trial design is growing, it remains uncommon

  8. Challenges to Designing Game-Based Business

    DEFF Research Database (Denmark)

    Henriksen, Thomas Duus

    2014-01-01

    The four categories labelled game-design, didactic design, organisational design and business design each constitute a set of challenges, each requiring a particular set of competencies. The key conclusion of the paper is that even though the learning game design constitutes the core of establish......The four categories labelled game-design, didactic design, organisational design and business design each constitute a set of challenges, each requiring a particular set of competencies. The key conclusion of the paper is that even though the learning game design constitutes the core...... of establishing game based business (GBB), the subsequent stages of development call for other kinds of competencies in order to become a viable GBB....

  9. Value-based management of design reuse

    Science.gov (United States)

    Carballo, Juan Antonio; Cohn, David L.; Belluomini, Wendy; Montoye, Robert K.

    2003-06-01

    Effective design reuse in electronic products has the potential to provide very large cost savings, substantial time-to-market reduction, and extra sources of revenue. Unfortunately, critical reuse opportunities are often missed because, although they provide clear value to the corporation, they may not benefit the business performance of an internal organization. It is therefore crucial to provide tools to help reuse partners participate in a reuse transaction when the transaction provides value to the corporation as a whole. Value-based Reuse Management (VRM) addresses this challenge by (a) ensuring that all parties can quickly assess the business performance impact of a reuse opportunity, and (b) encouraging high-value reuse opportunities by supplying value-based rewards to potential parties. In this paper we introduce the Value-Based Reuse Management approach and we describe key results on electronic designs that demonstrate its advantages. Our results indicate that Value-Based Reuse Management has the potential to significantly increase the success probability of high-value electronic design reuse.

  10. Design study of Thorium-232 and Protactinium-231 based fuel for long life BWR

    Energy Technology Data Exchange (ETDEWEB)

    Trianti, N.; Su' ud, Z.; Riyana, E. S. [Nuclear Physics and Biophysics Research Division Department of Physics - Institut Teknologi Bandung (ITB) Jalan Ganeca 10 Bandung 40132 (Indonesia)

    2012-06-06

    A preliminary design study for the utilization of thorium added with {sup 231}Pa based fuel on BWR type reactor has been performed. In the previous research utilization of fuel based Thorium-232 and Uranium-233 show 10 years operation time with maximum excess-reactivity about 4.075% dk/k. To increase reactor operation time and reduce excess-reactivity below 1% dk/k, Protactinium (Pa-231) is used as Burnable Poison. Protactinium-231 has very interesting neutronic properties, which enable the core to reduce initial excess-reactivity and simultaneously increase production of {sup 233}U to {sup 231}Pa in burn-up process. Optimizations of the content of {sup 231}Pa in the core enables the BWR core to sustain long period of operation time with reasonable burn-up reactivity swing. Based on the optimization of fuel element composition (Th and Pa) in various moderation ratio we can get reactor core with longer operation time, 20 {approx} 30 years operation without fuel shuffling or refuelling, with average power densities maximum of about 35 watt/cc, and maximum excess-reactivity 0.56% dk/k.

  11. BWID System Design Study

    International Nuclear Information System (INIS)

    O'Brien, M.C.; Rudin, M.J.; Morrison, J.L.; Richardson, J.G.

    1991-01-01

    The mission of the Buried Waste Integrated Demonstration (BWID) System Design Study is to identify and evaluate technology process options for the cradle-to-grave remediation of Transuranic (TRU)-Contaminated Waste Pits and Trenches buried at the Idaho National Engineering Laboratory (INEL). Emphasis is placed upon evaluating system configuration options and associated functional and operational requirements for retrieving and treating the buried wastes. A Performance-Based Technology Selection Filter was developed to evaluate the identified remediation systems and their enabling technologies based upon system requirements and quantification of technical Comprehensive Environmental Response, Compensation, and Liability (CERCLA) balancing criteria. Remediation systems will also be evaluated with respect to regulatory and institutional acceptance and cost-effectiveness

  12. Internet based remote cooperative engineering system for NSSS system design

    International Nuclear Information System (INIS)

    Kim, Y. S.; Lee, S. L.

    2000-01-01

    Implementation of information technology system through the nuclear power plant life cycle which covers site selection, design, construction, operation and decommission has been suggested continually by the reports or guidelines from NIRMA, INPO, NUMARC, USNRC and EPRI since late 1980's, and some of it has been actually implemented and applied partially to the practical design process. However, for the NSSS system design, a high level activity of nuclear power plant design phase, none of the effects has been reported with regard to implementing the information system. In Korea, KAERI studied NuIDEAS(Nuclear Integrated Database and Design Advancement System) in 1995, and KAERI (Korea Electric Power Research Institute) worked with CENP (Combustion Engineering Nuclear Power) for KNGR IMS(Information Management System) in 1997 as trials to adopt information system for NSSS system design. In this paper, after reviewing the pre-studied two information system, we introduce implementation of the information system for NSSS system design which is compatible with the on-going design works and can be used as means of concurrent engineering through internet. With this electronic design system, we expect increase of the design efficiency and productivity by switching from hard copy based design flow to internet based system. In addition, reliability and traceability of the design data is highly elevated by containing the native document file together with all the review, comment and resolution history in one database

  13. Computer-based teaching module design: principles derived from learning theories.

    Science.gov (United States)

    Lau, K H Vincent

    2014-03-01

    The computer-based teaching module (CBTM), which has recently gained prominence in medical education, is a teaching format in which a multimedia program serves as a single source for knowledge acquisition rather than playing an adjunctive role as it does in computer-assisted learning (CAL). Despite empirical validation in the past decade, there is limited research into the optimisation of CBTM design. This review aims to summarise research in classic and modern multimedia-specific learning theories applied to computer learning, and to collapse the findings into a set of design principles to guide the development of CBTMs. Scopus was searched for: (i) studies of classic cognitivism, constructivism and behaviourism theories (search terms: 'cognitive theory' OR 'constructivism theory' OR 'behaviourism theory' AND 'e-learning' OR 'web-based learning') and their sub-theories applied to computer learning, and (ii) recent studies of modern learning theories applied to computer learning (search terms: 'learning theory' AND 'e-learning' OR 'web-based learning') for articles published between 1990 and 2012. The first search identified 29 studies, dominated in topic by the cognitive load, elaboration and scaffolding theories. The second search identified 139 studies, with diverse topics in connectivism, discovery and technical scaffolding. Based on their relative representation in the literature, the applications of these theories were collapsed into a list of CBTM design principles. Ten principles were identified and categorised into three levels of design: the global level (managing objectives, framing, minimising technical load); the rhetoric level (optimising modality, making modality explicit, scaffolding, elaboration, spaced repeating), and the detail level (managing text, managing devices). This review examined the literature in the application of learning theories to CAL to develop a set of principles that guide CBTM design. Further research will enable educators to

  14. Design study on metal fuel FBR cores

    International Nuclear Information System (INIS)

    Yokoo, T.; Tanaka, Y.; Ogata, T.

    1991-01-01

    A design approach for metal fuel FBR core to maintain fuel integrity during transient events by limiting eutectic/liquid phase formation is proposed based on the current status of metallic fuel development. Its impact as the limitation on the core outlet temperature is assessed through its application to two of CRIEPI's core concepts, high linear power 1000 MWe homogeneous design and medium linear power 300 MWe radially heterogeneous design. SESAME/SALT code is used in this study to analyze steady state and transient fuel behavior. SE2-FA code is developed based on SUPERENERGY-2 and used to analyze core thermal-hydraulics with uncertainties. As the result, the core outlet temperatures of both designs are found to be limited to ≤500degC if it is required to prevent eutectic/liquid phase formation during operational transients in order to guarantee the fuel integrity. Additional assessment is made assuming an advanced limiting condition that allows small liquid phase formation based on the liquid phase penetration rate derived from existing experimental results. The result indicates possibility of raising core outlet temperature to ∼ 530degC. Also, it is found that core design technology improvements such as hot spot factors reduction can contribute to the core outlet temperature extension by 10 ∼ 20degC. (author)

  15. A Data Base Management System for Clinical and Epidemiologic Studies In Systemic Lupus Erythematosus: Design and Maintenance

    Science.gov (United States)

    Kosmides, Victoria S.; Hochberg, Marc C.

    1984-01-01

    This report describes the development, design specifications, features and implementation of a data base management system (DBMS) for clinical and epidemiologic studies in SLE. The DBMS is multidimensional with arrays formulated across patients, studies and variables. The major impact of this DBMS has been to increase the efficiency of managing and analyzing vast amounts of clinical and laboratory data and, as a result, to allow for continued growth in research productivity in areas related to SLE.

  16. Study on advanced structural design for commercialized fast breeder reactors

    International Nuclear Information System (INIS)

    Morishita, Masaki; Aoto, Kazumi; Kasahara, Naoto; Asayama, Tai

    2002-01-01

    Japan Nuclear Cycle Development Institute (JNC) and Japan Atomic Power Company (JAPC) launched joint research programs on structural design and three-dimensional seismic isolation technologies, as part of the supporting R and D activities for the feasibility studies on commercialized fast breeder reactor cycle systems. A research project by JAPC under the auspices of the Ministry of Economy, Trade, and Industry (METI) with technical support by JNC is included in this joint study. This report contains the results of the research on the structural design technology. The research scope was identified as (1) System Based Code for Integrity, (2) FDS (FBR Design Standard), and (3) Standardization of new material, and the results of this year's studies are summarized as follows. (1) System Based Code for Integrity. Requirements that a structural design standard must fulfill for enhanced reliability and economy were clarified. Based on this, the authors began to develop the system-based code for integrity. A structural reliability based design approach was proposed as a basic concept for an integrated evaluation of structural integrity. A system consisting of a supreme code and partial codes was proposed. Technologies and engineering tools that are necessary to materialize this code were clarified and research and development was begun. (2) FDS(FBR Design Standard). A rational design approach against thermal loads was proposed. Applicable area of inelastic analysis methods was investigated to develop inelastic analysis guide. A new design system which realizes feedback from structural to thermal hydraulic designs was proposed with a total analysis method of thermal hydraulic and mechanical behaviors. (3) Standardization of new material. Current status of development of high-chromium ferritic steels was investigated. Those steels have excellent high temperature strength and thermal properties. The authors proposed material specifications to apply those steels to structures

  17. Study on advanced structural design for commercialized fast breeder reactors

    Energy Technology Data Exchange (ETDEWEB)

    Morishita, Masaki; Aoto, Kazumi; Kasahara, Naoto; Asayama, Tai [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center; Sagayama, Yutaka; Dozaki, Koji; Tanaka, Yoshihiko [Japan Atomic Power Co., Research and Development Department, Tokyo (Japan)

    2002-01-01

    Japan Nuclear Cycle Development Institute (JNC) and Japan Atomic Power Company (JAPC) launched joint research programs on structural design and three-dimensional seismic isolation technologies, as part of the supporting R and D activities for the feasibility studies on commercialized fast breeder reactor cycle systems. A research project by JAPC under the auspices of the Ministry of Economy, Trade, and Industry (METI) with technical support by JNC is included in this joint study. This report contains the results of the research on the structural design technology. The research scope was identified as (1) System Based Code for Integrity, (2) FDS (FBR Design Standard), and (3) Standardization of new material, and the results of this year's studies are summarized as follows. (1) System Based Code for Integrity. Requirements that a structural design standard must fulfill for enhanced reliability and economy were clarified. Based on this, the authors began to develop the system-based code for integrity. A structural reliability based design approach was proposed as a basic concept for an integrated evaluation of structural integrity. A system consisting of a supreme code and partial codes was proposed. Technologies and engineering tools that are necessary to materialize this code were clarified and research and development was begun. (2) FDS(FBR Design Standard). A rational design approach against thermal loads was proposed. Applicable area of inelastic analysis methods was investigated to develop inelastic analysis guide. A new design system which realizes feedback from structural to thermal hydraulic designs was proposed with a total analysis method of thermal hydraulic and mechanical behaviors. (3) Standardization of new material. Current status of development of high-chromium ferritic steels was investigated. Those steels have excellent high temperature strength and thermal properties. The authors proposed material specifications to apply those steels to

  18. Framework for AI-based nuclear reactor design support system

    International Nuclear Information System (INIS)

    Furuta, Kazuo; Kondo, Shunsuke

    1992-01-01

    Nowadays many computer programs are being developed and used for the analytic tasks in nuclear reactor design, but experienced designers are still responsible for most of the synthetic tasks which are not amenable to algorithmic computer processes. Artificial intelligence (AI) is a promising technology to deal with these intractable tasks in design. In development of AI-based design support systems, it is desirable to choose a comprehensive framework based on the scientific theory of design. In this work a framework for AI-based design support systems for nuclear reactor design will be proposed based on an explorative abduction model of design. The fundamental architectures of this framework will be described especially on knowledge representation, context management and design planning. (author)

  19. Computer Based Training Authors' and Designers' training

    Directory of Open Access Journals (Sweden)

    Frédéric GODET

    2016-03-01

    Full Text Available This communication, through couple of studies driven since 10 years, tries to show how important is the training of authors in Computer Based Training (CBT. We submit here an approach to prepare designers mastering Interactive Multimedia modules in this domain. Which institutions are really dedicating their efforts in training authors and designers in this area of CBTs? Television devices and broadcast organisations offered since year 60s' a first support for Distance Learning. New media, New Information and Communication Technologies (NICT allowed several public and private organisations to start Distance Learning projects. As usual some of them met their training objectives, other of them failed. Did their really failed? Currently, nobody has the right answer. Today, we do not have enough efficient tools allowing us to evaluate trainees' acquisition in a short term view. Training evaluation needs more than 10 to 20 years of elapsed time to bring reliable measures. Nevertheless, given the high investments already done in this area, we cannot wait until the final results of the pedagogical evaluation. A lot of analyses showed relevant issues which can be used as directions for CBTs authors and designers training. Warning - Our studies and the derived conclusions are mainly based on projects driven in the field. We additionally bring our several years experience in the training of movie film authors in the design of interactive multimedia products. Some of our examples are extracting from vocational training projects where we were involved in all development phases from the analysis of needs to the evaluation of the acquisition within the trainee's / employee job's. Obviously, we cannot bring and exhaustive approach in this domain where a lot of parameters are involved as frame for the CBT interactive multimedia modules authors' and designers' training.

  20. Reliability-based design of wind turbine blades

    DEFF Research Database (Denmark)

    Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

    2011-01-01

    Reliability-based design of wind turbine blades requires identification of the important failure modes/limit states along with stochastic models for the uncertainties and methods for estimating the reliability. In the present paper it is described how reliability-based design can be applied to wi...

  1. Above-knee prosthesis design based on fatigue life using finite element method and design of experiment.

    Science.gov (United States)

    Phanphet, Suwattanarwong; Dechjarern, Surangsee; Jomjanyong, Sermkiat

    2017-05-01

    The main objective of this work is to improve the standard of the existing design of knee prosthesis developed by Thailand's Prostheses Foundation of Her Royal Highness The Princess Mother. The experimental structural tests, based on the ISO 10328, of the existing design showed that a few components failed due to fatigue under normal cyclic loading below the required number of cycles. The finite element (FE) simulations of structural tests on the knee prosthesis were carried out. Fatigue life predictions of knee component materials were modeled based on the Morrow's approach. The fatigue life prediction based on the FE model result was validated with the corresponding structural test and the results agreed well. The new designs of the failed components were studied using the design of experimental approach and finite element analysis of the ISO 10328 structural test of knee prostheses under two separated loading cases. Under ultimate loading, knee prosthesis peak von Mises stress must be less than the yield strength of knee component's material and the total knee deflection must be lower than 2.5mm. The fatigue life prediction of all knee components must be higher than 3,000,000 cycles under normal cyclic loading. The design parameters are the thickness of joint bars, the diameter of lower connector and the thickness of absorber-stopper. The optimized knee prosthesis design meeting all the requirements was recommended. Experimental ISO 10328 structural test of the fabricated knee prosthesis based on the optimized design confirmed the finite element prediction. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

  2. Hypermedia-Based Problem Based Learning in the Upper Elementary Grades: A Developmental Study.

    Science.gov (United States)

    Brinkerhoff, Jonathan D.; Glazewski, Krista

    This paper describes the application of problem-based learning (PBL) design principles and the inclusion of teacher and study scaffolds to the design and implementation of a hypermedia-based learning unit for the upper elementary/middle school grades. The study examined the following research questions: (1) Does hypermedia-based PBL represent an…

  3. Overview of Performance Based Practical Design

    Science.gov (United States)

    2018-03-01

    DOI: https://doi.org/10.13023/KTC.RR.2018.03 State transportation agencies (STAs) have increasingly turned to practical design and performance based practical design(PBPD) to inform project development and implementation and to reduce project cos...

  4. Implementing Set Based Design into Department of Defense Acquisition

    Science.gov (United States)

    2016-12-01

    The team employed a tailored waterfall process model in order to explore SBD applications in the support of defense acquisition and PORs. Figure 1...Engineering Model . Additionally, the team reviewed DOD case studies that implemented SBD. The SBD principles, along with the common themes from the...acquisition. 14. SUBJECT TERMS set based design, set based thinking, model based systems engineering, concurrent engineering, defense acquisition

  5. Evaluating design-based formative assessment practices in outdoor science teaching

    DEFF Research Database (Denmark)

    Hartmeyer, Rikke; Stevenson, Matthew Peter; Bentsen, Peter

    2016-01-01

    Background and purpose: Research in formative assessment often pays close attention to the strategies which can be used by teachers. However, less emphasis in the literature seems to have been paid to study the application of formative assessment designs in practice. In this paper, we argue...... that a formative assessment design that we call Eva-Mapping, which is developed on the principles of design-based research, can be a productive starting point for disseminating and further developing formative assessment practices in outdoor science teaching. Sample, design and methods: We conducted an evaluation...... of the design, based on video-elicited focus group interviews with two groups of experienced science teachers. Both groups consisted of teachers who taught science outside the classroom on a regular basis. These groups watched identical video sequences which were recorded during lessons in which teachers...

  6. Effects of Cloud-Based m-Learning on Student Creative Performance in Engineering Design

    Science.gov (United States)

    Chang, Yu-Shan; Chen, Si-Yi; Yu, Kuang-Chao; Chu, Yih-Hsien; Chien, Yu-Hung

    2017-01-01

    This study explored the effects of cloud-based m-learning on students' creative processes and products in engineering design. A nonequivalent pretest-posttest design was adopted, and 62 university students from Taipei City, Taiwan, were recruited as research participants in the study. The results showed that cloud-based m-learning had a positive…

  7. Designing and Implementing a Mentoring Program to Support Clinically-Based Teacher Education

    Science.gov (United States)

    Henning, John E.; Gut, Dianne; Beam, Pamela

    2015-01-01

    This article describes one teacher preparation program's approach to designing and implementing a mentoring program to support clinically-based teacher education. The design for the program is based on an interview study that compared the mentoring experiences of 18 teachers across three different contexts: student teaching, early field…

  8. Design values of resilient modulus of stabilized and non-stabilized base.

    Science.gov (United States)

    2010-10-01

    The primary objective of this research study is to determine design value ranges for typical base materials, as allowed by LADOTD specifications, through laboratory tests with respect to resilient modulus and other parameters used by pavement design ...

  9. Reliability-based design code calibration for concrete containment structures

    International Nuclear Information System (INIS)

    Han, B.K.; Cho, H.N.; Chang, S.P.

    1991-01-01

    In this study, a load combination criteria for design and a probability-based reliability analysis were proposed on the basis of a FEM-based random vibration analysis. The limit state model defined for the study is a serviceability limit state of the crack failure that causes the emission of radioactive materials, and the results are compared with the case of strength limit state. More accurate reliability analyses under various dynamic loads such as earthquake loads were made possible by incorporating the FEM and random vibration theory, which is different from the conventional reliability analysis method. The uncertainties in loads and resistance available in Korea and the references were adapted to the situation of Korea, and especially in case of earthquake, the design earthquake was assessed based on the available data for the probabilistic description of earthquake ground acceleration in the Korea peninsula. The SAP V-2 is used for a three-dimensional finite element analysis of concrete containment structure, and the reliability analysis is carried out by modifying HRAS reliability analysis program for this study. (orig./GL)

  10. Spaceborne computer executive routine functional design specification. Volume 2: Computer executive design for space station/base

    Science.gov (United States)

    Kennedy, J. R.; Fitzpatrick, W. S.

    1971-01-01

    The computer executive functional system design concepts derived from study of the Space Station/Base are presented. Information Management System hardware configuration as directly influencing the executive design is reviewed. The hardware configuration and generic executive design requirements are considered in detail in a previous report (System Configuration and Executive Requirements Specifications for Reusable Shuttle and Space Station/Base, 9/25/70). This report defines basic system primitives and delineates processes and process control. Supervisor states are considered for describing basic multiprogramming and multiprocessing systems. A high-level computer executive including control of scheduling, allocation of resources, system interactions, and real-time supervisory functions is defined. The description is oriented to provide a baseline for a functional simulation of the computer executive system.

  11. Quantitative methods for studying design protocols

    CERN Document Server

    Kan, Jeff WT

    2017-01-01

    This book is aimed at researchers and students who would like to engage in and deepen their understanding of design cognition research. The book presents new approaches for analyzing design thinking and proposes methods of measuring design processes. These methods seek to quantify design issues and design processes that are defined based on notions from the Function-Behavior-Structure (FBS) design ontology and from linkography. A linkograph is a network of linked design moves or segments. FBS ontology concepts have been used in both design theory and design thinking research and have yielded numerous results. Linkography is one of the most influential and elegant design cognition research methods. In this book Kan and Gero provide novel and state-of-the-art methods of analyzing design protocols that offer insights into design cognition by integrating segmentation with linkography by assigning FBS-based codes to design moves or segments and treating links as FBS transformation processes. They propose and test ...

  12. Study of Fuze Structure and Reliability Design Based on the Direct Search Method

    Science.gov (United States)

    Lin, Zhang; Ning, Wang

    2017-03-01

    Redundant design is one of the important methods to improve the reliability of the system, but mutual coupling of multiple factors is often involved in the design. In my study, Direct Search Method is introduced into the optimum redundancy configuration for design optimization, in which, the reliability, cost, structural weight and other factors can be taken into account simultaneously, and the redundant allocation and reliability design of aircraft critical system are computed. The results show that this method is convenient and workable, and applicable to the redundancy configurations and optimization of various designs upon appropriate modifications. And this method has a good practical value.

  13. The Study on Human-Computer Interaction Design Based on the Users’ Subconscious Behavior

    Science.gov (United States)

    Li, Lingyuan

    2017-09-01

    Human-computer interaction is human-centered. An excellent interaction design should focus on the study of user experience, which greatly comes from the consistence between design and human behavioral habit. However, users’ behavioral habits often result from subconsciousness. Therefore, it is smart to utilize users’ subconscious behavior to achieve design's intention and maximize the value of products’ functions, which gradually becomes a new trend in this field.

  14. Web-based Core Design System Development

    International Nuclear Information System (INIS)

    Moon, So Young; Kim, Hyung Jin; Yang, Sung Tae; Hong, Sun Kwan

    2011-01-01

    The selection of a loading pattern is one of core design processes in the operation of a nuclear power plant. A potential new loading pattern is identified by selecting fuels that to not exceed the major limiting factors of the design and that satisfy the core design conditions for employing fuel data from the existing loading pattern of the current operating cycle. The selection of a loading pattern is also related to the cycle plan of an operating nuclear power plant and must meet safety and economic requirements. In selecting an appropriate loading pattern, all aspects, such as input creation, code runs and result processes are processed as text forms manually by a designer, all of which may be subject to human error, such as syntax or running errors. Time-consuming results analysis and decision-making processes are the most significant inefficiencies to avoid. A web-based nuclear plant core design system was developed here to remedy the shortcomings of an existing core design system. The proposed system adopts the general methodology of OPR1000 (Korea Standard Nuclear Power Plants) and Westinghouse-type plants. Additionally, it offers a GUI (Graphic User Interface)-based core design environment with a user-friendly interface for operators. It reduces human errors related to design model creation, computation, final reload core model selection, final output confirmation, and result data validation and verification. Most significantly, it reduces the core design time by more than 75% compared to its predecessor

  15. Reliability Based Ship Structural Design

    DEFF Research Database (Denmark)

    Dogliani, M.; Østergaard, C.; Parmentier, G.

    1996-01-01

    This paper deals with the development of different methods that allow the reliability-based design of ship structures to be transferred from the area of research to the systematic application in current design. It summarises the achievements of a three-year collaborative research project dealing...... with developments of models of load effects and of structural collapse adopted in reliability formulations which aim at calibrating partial safety factors for ship structural design. New probabilistic models of still-water load effects are developed both for tankers and for containerships. New results are presented...... structure of several tankers and containerships. The results of the reliability analysis were the basis for the definition of a target safety level which was used to asses the partial safety factors suitable for in a new design rules format to be adopted in modern ship structural design. Finally...

  16. Reliability Based Geometric Design of Horizontal Circular Curves

    Science.gov (United States)

    Rajbongshi, Pabitra; Kalita, Kuldeep

    2018-06-01

    Geometric design of horizontal circular curve primarily involves with radius of the curve and stopping sight distance at the curve section. Minimum radius is decided based on lateral thrust exerted on the vehicles and the minimum stopping sight distance is provided to maintain the safety in longitudinal direction of vehicles. Available sight distance at site can be regulated by changing the radius and middle ordinate at the curve section. Both radius and sight distance depend on design speed. Speed of vehicles at any road section is a variable parameter and therefore, normally the 98th percentile speed is taken as the design speed. This work presents a probabilistic approach for evaluating stopping sight distance, considering the variability of all input parameters of sight distance. It is observed that the 98th percentile sight distance value is much lower than the sight distance corresponding to 98th percentile speed. The distribution of sight distance parameter is also studied and found to follow a lognormal distribution. Finally, the reliability based design charts are presented for both plain and hill regions, and considering the effect of lateral thrust.

  17. Reliability Based Geometric Design of Horizontal Circular Curves

    Science.gov (United States)

    Rajbongshi, Pabitra; Kalita, Kuldeep

    2018-03-01

    Geometric design of horizontal circular curve primarily involves with radius of the curve and stopping sight distance at the curve section. Minimum radius is decided based on lateral thrust exerted on the vehicles and the minimum stopping sight distance is provided to maintain the safety in longitudinal direction of vehicles. Available sight distance at site can be regulated by changing the radius and middle ordinate at the curve section. Both radius and sight distance depend on design speed. Speed of vehicles at any road section is a variable parameter and therefore, normally the 98th percentile speed is taken as the design speed. This work presents a probabilistic approach for evaluating stopping sight distance, considering the variability of all input parameters of sight distance. It is observed that the 98th percentile sight distance value is much lower than the sight distance corresponding to 98th percentile speed. The distribution of sight distance parameter is also studied and found to follow a lognormal distribution. Finally, the reliability based design charts are presented for both plain and hill regions, and considering the effect of lateral thrust.

  18. Study of high field Nb3Sn superconducting dipoles: electrical insulation based made of ceramic and magnetic design

    International Nuclear Information System (INIS)

    Rochepault, E.

    2012-01-01

    In the framework of LHC upgrades, significant efforts are provided to design accelerator magnets using the superconducting alloy Nb 3 Sn, which allows to reach higher magnetic fields (≥12 T). The aim of this thesis is to propose new computation and manufacturing methods for high field Nb 3 Sn dipoles. A ceramic insulation, previously designed at CEA Saclay, has been tested for the first time on cables, in an accelerator magnet environment. Critical current measures, under magnetic field and mechanical stress, have been carried out in particular. With this test campaign, the current ceramic insulation has been shown to be too weak mechanically and the critical current properties are degraded. Then a study has been conducted, with the objective to improve the mechanical strength of the insulation and better distribute the stress inside the cable. Methods of magnetic design have also been proposed, in order to optimize the coils shape, while fulfilling constraints of field homogeneity, operational margins, forces minimization... Consequently, several optimization codes have been set up. They are based on new methods using analytical formulas. A 2D code has first been written for block designs. Then two 3D codes have been realized for the optimization of dipole ends. The former consists in modeling the coil with elementary blocs and the latter is based on a modeling of the superconducting cables with ribbons. These optimization codes allowed to propose magnetic designs for high field accelerator magnets. (author) [fr

  19. SLS Model Based Design: A Navigation Perspective

    Science.gov (United States)

    Oliver, T. Emerson; Anzalone, Evan; Park, Thomas; Geohagan, Kevin

    2018-01-01

    The SLS Program has implemented a Model-based Design (MBD) and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team is responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1B design, the additional GPS Receiver hardware model is managed as a DMM at the vehicle design level. This paper describes the models, and discusses the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the navigation components.

  20. A study on the development of an infographic designer questionnaire and designer opinions

    Directory of Open Access Journals (Sweden)

    Yıldırım Serkan

    2016-01-01

    Full Text Available Technological developments and changes in how learning is understood have not only changed learning environments, but also how educational materials are developed. Infographics, one of the materials that are becoming increasingly more popular in learning environments, have nowadays become quite commonplace. Demonstrating the understanding of those who design such instructional materials is important with respect to the organisation of learning processes. In this study, we devised a questionnaire that aims to demonstrate the understanding infographic designers have of infographic design. A total of 94 students from the Department of Computer and Instructional Technologies Education of the Kazım Karabekir Faculty of Education took part in this study conducted during the fall semester of the 2013–2014 academic year. The participants were given a questionnaire consisting of 41 items that enquired about the readers’ views regarding infographic design. The collected data were assessed using Principal Component Analysis. Based on the analysis results, a questionnaire form consisting of 27 items and 8 factors (Understanding of Design, Design Process, Copyrights, Introduction, Readability, Sharing, References, Development was developed.

  1. Ergonomic study and static analysis for new design of electric scooter

    Science.gov (United States)

    Fadzly, M. K.; Munirah, Anis; Shayfull, Z.; Saad, Mohd Sazli

    2017-09-01

    The purposes of this project are to design and diversify the function of a battery powered scooter frame which is more practical for the human factor in ergonomic and optimum design. The new design is based on ideas which are studied from existing scooter frame, United States Patent design and European States International Patent design. The final idea of concept design for scooter frame is based on concept chosen from the best characteristics and it is divided into three main difference ideas and the matrix evaluation method is applied. Analysis that applies to frame design, arm, rim and drive train component is based on Cosmos Express program. As a conclusion, the design that is produce are able to carry the maximum also has more practical features in ergonomic view.

  2. An Empirical Study on Design Partner Selection in Green Product Collaboration Design

    Directory of Open Access Journals (Sweden)

    Aijun Liu

    2018-01-01

    Full Text Available Green production has become an important issue in PCD (Product Collaboration Design for almost every enterprise, and will determine the sustainability of enterprises in the long term. The choice of design partner is a necessary condition in order to achieve green production. For the uncertain, fuzzy, and dynamic information such as unknown indices and weights, fuzzy semantics, and dynamic time factors in GPCD (Green Product Collaboration Design, a two-stage dynamic hybrid MADM (Multi-Attribute Decision Making approach based on fuzzy DEMATEL (Decision-Making and Trial Evaluation Laboratory, fuzzy KMA (Karnik–Mendel Algorithm, and fuzzy VIKOR (VlseKriterjumska Optimizacija I Kompromisno Resenje was proposed. In the first stage, fuzzy DEMATEL was used to determine the evaluation indices. Then, in the second stage, to accurately depict the dynamic information generated by the different phases of a product design, the dynamic evaluation method based on fuzzy theories was employed, and the weights of the indices were calculated by fuzzy KMA, then sorted by fuzzy VIKOR. Finally, a case study and a comparative analysis wre provided to illustrate the effectiveness of the proposed approach.

  3. Variation in choice of study design: findings from the Epidemiology Design Decision Inventory and Evaluation (EDDIE) survey.

    Science.gov (United States)

    Stang, Paul E; Ryan, Patrick B; Overhage, J Marc; Schuemie, Martijn J; Hartzema, Abraham G; Welebob, Emily

    2013-10-01

    Researchers using observational data to understand drug effects must make a number of analytic design choices that suit the characteristics of the data and the subject of the study. Review of the published literature suggests that there is a lack of consistency even when addressing the same research question in the same database. To characterize the degree of similarity or difference in the method and analysis choices made by observational database research experts when presented with research study scenarios. On-line survey using research scenarios on drug-effect studies to capture method selection and analysis choices that follow a dependency branching based on response to key questions. Voluntary participants experienced in epidemiological study design solicited for participation through registration on the Observational Medical Outcomes Partnership website, membership in particular professional organizations, or links in relevant newsletters. Description (proportion) of respondents selecting particular methods and making specific analysis choices based on individual drug-outcome scenario pairs. The number of questions/decisions differed based on stem questions of study design, time-at-risk, outcome definition, and comparator. There is little consistency across scenarios, by drug or by outcome of interest, in the decisions made for design and analyses in scenarios using large healthcare databases. The most consistent choice was the cohort study design but variability in the other critical decisions was common. There is great variation among epidemiologists in the design and analytical choices that they make when implementing analyses in observational healthcare databases. These findings confirm that it will be important to generate empiric evidence to inform these decisions and to promote a better understanding of the impact of standardization on research implementation.

  4. Intuitive web-based experimental design for high-throughput biomedical data.

    Science.gov (United States)

    Friedrich, Andreas; Kenar, Erhan; Kohlbacher, Oliver; Nahnsen, Sven

    2015-01-01

    Big data bioinformatics aims at drawing biological conclusions from huge and complex biological datasets. Added value from the analysis of big data, however, is only possible if the data is accompanied by accurate metadata annotation. Particularly in high-throughput experiments intelligent approaches are needed to keep track of the experimental design, including the conditions that are studied as well as information that might be interesting for failure analysis or further experiments in the future. In addition to the management of this information, means for an integrated design and interfaces for structured data annotation are urgently needed by researchers. Here, we propose a factor-based experimental design approach that enables scientists to easily create large-scale experiments with the help of a web-based system. We present a novel implementation of a web-based interface allowing the collection of arbitrary metadata. To exchange and edit information we provide a spreadsheet-based, humanly readable format. Subsequently, sample sheets with identifiers and metainformation for data generation facilities can be created. Data files created after measurement of the samples can be uploaded to a datastore, where they are automatically linked to the previously created experimental design model.

  5. Norm based design of fault detectors

    DEFF Research Database (Denmark)

    Rank, Mike Lind; Niemann, Hans Henrik

    1999-01-01

    The design of fault detectors for fault detection and isolation (FDI) in dynamic systems is considered in this paper from a norm based point of view. An analysis of norm based threshold selection is given based on different formulations of FDI problems. Both the nominal FDI problem as well...

  6. Model based design introduction: modeling game controllers to microprocessor architectures

    Science.gov (United States)

    Jungwirth, Patrick; Badawy, Abdel-Hameed

    2017-04-01

    We present an introduction to model based design. Model based design is a visual representation, generally a block diagram, to model and incrementally develop a complex system. Model based design is a commonly used design methodology for digital signal processing, control systems, and embedded systems. Model based design's philosophy is: to solve a problem - a step at a time. The approach can be compared to a series of steps to converge to a solution. A block diagram simulation tool allows a design to be simulated with real world measurement data. For example, if an analog control system is being upgraded to a digital control system, the analog sensor input signals can be recorded. The digital control algorithm can be simulated with the real world sensor data. The output from the simulated digital control system can then be compared to the old analog based control system. Model based design can compared to Agile software develop. The Agile software development goal is to develop working software in incremental steps. Progress is measured in completed and tested code units. Progress is measured in model based design by completed and tested blocks. We present a concept for a video game controller and then use model based design to iterate the design towards a working system. We will also describe a model based design effort to develop an OS Friendly Microprocessor Architecture based on the RISC-V.

  7. Game Theory and Risk-Based Levee System Design

    Science.gov (United States)

    Hui, R.; Lund, J. R.; Madani, K.

    2014-12-01

    Risk-based analysis has been developed for optimal levee design for economic efficiency. Along many rivers, two levees on opposite riverbanks act as a simple levee system. Being rational and self-interested, land owners on each river bank would tend to independently optimize their levees with risk-based analysis, resulting in a Pareto-inefficient levee system design from the social planner's perspective. Game theory is applied in this study to analyze decision making process in a simple levee system in which the land owners on each river bank develop their design strategies using risk-based economic optimization. For each land owner, the annual expected total cost includes expected annual damage cost and annualized construction cost. The non-cooperative Nash equilibrium is identified and compared to the social planner's optimal distribution of flood risk and damage cost throughout the system which results in the minimum total flood cost for the system. The social planner's optimal solution is not feasible without appropriate level of compensation for the transferred flood risk to guarantee and improve conditions for all parties. Therefore, cooperative game theory is then employed to develop an economically optimal design that can be implemented in practice. By examining the game in the reversible and irreversible decision making modes, the cost of decision making myopia is calculated to underline the significance of considering the externalities and evolution path of dynamic water resource problems for optimal decision making.

  8. Core design and fuel management studies

    International Nuclear Information System (INIS)

    Min, Byung Joo; Chan, P.

    1997-06-01

    The design target for the CANDU 9 requires a 20% increase in electrical power output from an existing 480-channel CANDU core. Assuming a net electrical output of 861 MW(e) for a natural uranium fuelled Bruce-B/Darlington reactor in a warm water site, the net electrical output of the reference CANDU 9 reactor would be 1033 MW(e). This report documents the result of the physics studies for the design of the CANDU 9 480/SEU core. The results of the core design and fuel management studies of the CANDU 9 480/SEU reactor indicated that up to 1033 MW(e) output can be achieved in a 480-channel CANDU core by using SEU core can easily be maintained indefinitely using an automated refuelling program. Fuel performance evaluation based on the data of the 500 FPDs refuelling simulation concluded that SEU fuel failure is not expected. (author). 2 tabs., 38 figs., 5 refs

  9. Computer-aided system of evaluation for population-based all-in-one service screening (CASE-PASS): from study design to outcome analysis with bias adjustment.

    Science.gov (United States)

    Chen, Li-Sheng; Yen, Amy Ming-Fang; Duffy, Stephen W; Tabar, Laszlo; Lin, Wen-Chou; Chen, Hsiu-Hsi

    2010-10-01

    Population-based routine service screening has gained popularity following an era of randomized controlled trials. The evaluation of these service screening programs is subject to study design, data availability, and the precise data analysis for adjusting bias. We developed a computer-aided system that allows the evaluation of population-based service screening to unify these aspects and facilitate and guide the program assessor to efficiently perform an evaluation. This system underpins two experimental designs: the posttest-only non-equivalent design and the one-group pretest-posttest design and demonstrates the type of data required at both the population and individual levels. Three major analyses were developed that included a cumulative mortality analysis, survival analysis with lead-time adjustment, and self-selection bias adjustment. We used SAS AF software to develop a graphic interface system with a pull-down menu style. We demonstrate the application of this system with data obtained from a Swedish population-based service screen and a population-based randomized controlled trial for the screening of breast, colorectal, and prostate cancer, and one service screening program for cervical cancer with Pap smears. The system provided automated descriptive results based on the various sources of available data and cumulative mortality curves corresponding to the study designs. The comparison of cumulative survival between clinically and screen-detected cases without a lead-time adjustment are also demonstrated. The intention-to-treat and noncompliance analysis with self-selection bias adjustments are also shown to assess the effectiveness of the population-based service screening program. Model validation was composed of a comparison between our adjusted self-selection bias estimates and the empirical results on effectiveness reported in the literature. We demonstrate a computer-aided system allowing the evaluation of population-based service screening

  10. Design and Methods for a Pilot Study of a Phone-Delivered, Mindfulness-Based Intervention in Patients with Implantable Cardioverter Defibrillators

    Directory of Open Access Journals (Sweden)

    Elena Salmoirago-Blotcher

    2012-01-01

    Full Text Available Background. Meditation practices are associated with a reduction in adrenergic activity that may benefit patients with severe cardiac arrhythmias. This paper describes the design and methods of a pilot study testing the feasibility of a phone-delivered mindfulness-based intervention (MBI for treatment of anxiety in patients with implantable cardioverter defibrillators (ICDs. Design and Methods. Consecutive, clinically stable outpatients (n=52 will be screened for study eligibility within a month of an ICD-related procedure or ICD shock and will be randomly assigned to MBI or to usual care. MBI patients will receive eight weekly individual phone sessions based on two mindfulness practices (awareness of breath and body scan plus home practice with a CD for 20 minutes daily. Patients assigned to usual care will be offered the standard care planned by the hospital. Assessments will occur at baseline and at the completion of the intervention (between 9 and 12 weeks after randomization. The primary study outcome is feasibility; secondary outcomes include anxiety, mindfulness, and number of administered shocks during the intervention period. Conclusions. If proven feasible and effective, phone-delivered mindfulness-based interventions could improve psychological distress in ICD outpatients with serious cardiovascular conditions.

  11. Designing robust control-based HIV-treatment

    Directory of Open Access Journals (Sweden)

    Fredy Andrés Olarte Dussán

    2008-05-01

    Full Text Available Designing a robust control-based treatment for human immunodeficiency virus (HIV-infected patients was studied. The dynamics of the immune system’s response to infection was modelled using a 5th order nonlinear model with separate efficacy coefficients for protease inhibitor (PIs and reverse transcriptase inhibitors (RTIs. The immune res-ponse has been represented as an uncertain system due to errors in parameter estimation and the existence of un-modelled dynamics. A polytopic system was constructed incorporating all possible system parameter values. A con-trol system was designed using robust pole location techniques stabilising the polytopic system around an equilibrium point having a low viral load. Numerical simulation results (including the organism’s pharmacokinetical response to anti-retroviral drugs showed that the control law could lead to long-term stable conditions, even in extreme cases.

  12. Transducers for Sound and Vibration - FEM Based Design

    DEFF Research Database (Denmark)

    Liu, Bin

    2001-01-01

    Design of transducers for measurement of vibration (piezoelectric accelerometers) and sound (condenser microphones) is a very labour intensive work. The design work is mostly based on experience and on simple analogies to electrical circuit design. Often a time consuming itterative loop is used......: Specification of the transducer, production of a physical prototype, measurements on the prototype, changed specification of the transducer etc. Furthermore are many transducers made based on customer requirements which also increases the amount of required design work. For these reasons there is a need...... for methods that can reduce the design time consumption and the number of itterations. The present work proposes to use finite element based programs for simulating the behaviour of a transducer with a given set of specifications. A simulation program for accelerometers was developed and has been tested...

  13. Embracing First-Person Perspectives in Soma-Based Design

    Directory of Open Access Journals (Sweden)

    Kristina Höök

    2018-02-01

    Full Text Available A set of prominent designers embarked on a research journey to explore aesthetics in movement-based design. Here we unpack one of the design sensitivities unique to our practice: a strong first person perspective—where the movements, somatics and aesthetic sensibilities of the designer, design researcher and user are at the forefront. We present an annotated portfolio of design exemplars and a brief introduction to some of the design methods and theory we use, together substantiating and explaining the first-person perspective. At the same time, we show how this felt dimension, despite its subjective nature, is what provides rigor and structure to our design research. Our aim is to assist researchers in soma-based design and designers wanting to consider the multiple facets when designing for the aesthetics of movement. The applications span a large field of designs, including slow introspective, contemplative interactions, arts, dance, health applications, games, work applications and many others.

  14. COA based robust output feedback UPFC controller design

    Energy Technology Data Exchange (ETDEWEB)

    Shayeghi, H., E-mail: hshayeghi@gmail.co [Technical Engineering Department, University of Mohaghegh Ardabili, Ardabil (Iran, Islamic Republic of); Shayanfar, H.A. [Center of Excellence for Power System Automation and Operation, Electrical Engineering Department, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Jalilzadeh, S.; Safari, A. [Technical Engineering Department, Zanjan University, Zanjan (Iran, Islamic Republic of)

    2010-12-15

    In this paper, a novel method for the design of output feedback controller for unified power flow controller (UPFC) using chaotic optimization algorithm (COA) is developed. Chaotic optimization algorithms, which have the features of easy implementation, short execution time and robust mechanisms of escaping from the local optimum, is a promising tool for the engineering applications. The selection of the output feedback gains for the UPFC controllers is converted to an optimization problem with the time domain-based objective function which is solved by a COA based on Lozi map. Since chaotic mapping enjoys certainty, ergodicity and the stochastic property, the proposed chaotic optimization problem introduces chaos mapping using Lozi map chaotic sequences which increases its convergence rate and resulting precision. To ensure the robustness of the proposed stabilizers, the design process takes into account a wide range of operating conditions and system configurations. The effectiveness of the proposed controller for damping low frequency oscillations is tested and demonstrated through non-linear time-domain simulation and some performance indices studies. The results analysis reveals that the designed COA based output feedback UPFC damping controller has an excellent capability in damping power system low frequency oscillations and enhance greatly the dynamic stability of the power systems.

  15. A Participatory Design Approach for a Mobile App-Based Personal Response System

    Science.gov (United States)

    Song, Donggil; Oh, Eun Young

    2016-01-01

    This study reports on a participatory design approach including the design, development, implementation, and evaluation of a mobile app-based personal response system (PRS). The first cycle formulated initial design principles through context and needs analysis; the second utilized the collaboration with instructors and experts embodying specific…

  16. Direct displacement-based design of special composite RC shear walls with steel boundary elements

    Directory of Open Access Journals (Sweden)

    H. Kazemi

    2016-06-01

    Full Text Available Special composite RC shear wall (CRCSW with steel boundary elements is a kind of lateral force resisting structural system which is used in earthquake-prone regions. Due to their high ductility and energy dissipation, CRCSWs have been widely used in recent years by structural engineers. However, there are few studies in the literature on the seismic design of such walls. Although there are many studies in the literature on the Direct Displacement-Based Design (DDBD of RC structures, however, no study can be found on DDBD of CRCSWs. Therefore, the aim of present study is to evaluate the ability of DDBD method for designing CRCSWs. In this study, four special composite reinforced concrete shear walls with steel boundary elements of 4, 8, 12 and 16 story numbers were designed using the DDBD method for target drift of 2%. The seismic behavior of the four CRCSWs was studied using nonlinear time-history dynamic analyses. Dynamic analyses were performed for the mentioned walls using 7 selected earthquake records. The seismic design parameters considered in this study includes: lateral displacement profile, inelastic dynamic inter-story drift demand, failure pattern and the composite RC shear walls overstrength factor. For each shear wall, the overall overstrength factor was calculated by dividing the ultimate dynamic base shear demand (Vu by the base shear demand (Vd as per the Direct Displacement Based-Design (DDBD method. The results show that the DDBD method can be used to design CRCSWs safely in seismic regions with predicted behavior.

  17. Product design pattern based on big data-driven scenario

    Directory of Open Access Journals (Sweden)

    Conggang Yu

    2016-07-01

    Full Text Available This article discusses about new product design patterns in the big data era, gives designer a new rational thinking way, and is a new way to understand the design of the product. Based on the key criteria of the product design process, category, element, and product are used to input the data, which comprises concrete data and abstract data as an enlargement of the criteria of product design process for the establishment of a big data-driven product design pattern’s model. Moreover, an experiment and a product design case are conducted to verify the feasibility of the new pattern. Ultimately, we will conclude that the data-driven product design has two patterns: one is the concrete data supporting the product design, namely “product–data–product” pattern, and the second is based on the value of the abstract data for product design, namely “data–product–data” pattern. Through the data, users are involving themselves in the design development process. Data and product form a huge network, and data plays a role of connection or node. So the essence of the design is to find a new connection based on element, and to find a new node based on category.

  18. THE DESIGN OF KNOWLEDGE BASE FOR SURFACE RELATIONS BASED PART RECOGNITION APPROACH

    Directory of Open Access Journals (Sweden)

    Adem ÇİÇEK

    2007-01-01

    Full Text Available In this study, a new knowledge base for an expert system used in part recognition algorithm has been designed. Parts are recognized by the computer program by comparing face adjacency relations and attributes belonging to each part represented in the rules in the knowledge base developed with face adjacency relations and attributes generated from STEP file of the part. Besides, rule writing process has been quite simplified by generating the rules represented in the knowledge base with an automatic rule writing module developed within the system. With the knowledge base and automatic rule writing module used in the part recognition system, simple, intermediate and complex parts can be recognized by a part recognition program.

  19. Sustainability and evidence-based design in the healthcare estate

    CERN Document Server

    Phiri, Michael

    2014-01-01

    This work aims to deepen our understanding of the role played by technical guidelines and tools for the design, construction and operation of healthcare facilities, ultimately establishing the impact of the physical environment on staff and patient outcomes. Using case studies largely drawn from the UK, Europe, China and Australasia, design approaches such as sustainability (e.g. targets for energy efficiency, carbon neutrality, reduction of waste), evidence-based design (EBD), and Post-Project Evaluation (PPE) are examined in order to identify policies, mechanisms and strategies that can promote an integrated learning environment that in turn supports innovation in healthcare.

  20. Systematic Optimization-Based Integrated Chemical Product–Process Design Framework

    DEFF Research Database (Denmark)

    Cignitti, Stefano; Mansouri, Seyed Soheil; Woodley, John M.

    2018-01-01

    An integrated optimization-based framework for product and process design is proposed. The framework uses a set of methods and tools to obtain the optimal product–process design solution given a set of economic and environmental sustainability targets. The methods and tools required are property...... of the framework is demonstrated through three case studies: (i) refrigeration cycle unit for R134a replacement, (ii) a mixed working fluid design problem for R134a replacement, and (iii) pure solvent design for water-acetic acid LLE extraction. Through the application of the framework it is demonstrated that all...... prediction through group contributions, unless supported with a database, computer-aided molecular and mixture/blend design for generation of novel as well as existing products and mathematical programming for formulating and solving multiscale integrated process–product design problems. The application...

  1. Design and Parametric Study of the Magnetic Sensor for Position Detection in Linear Motor Based on Nonlinear Parametric model order reduction.

    Science.gov (United States)

    Paul, Sarbajit; Chang, Junghwan

    2017-07-01

    This paper presents a design approach for a magnetic sensor module to detect mover position using the proper orthogonal decomposition-dynamic mode decomposition (POD-DMD)-based nonlinear parametric model order reduction (PMOR). The parameterization of the sensor module is achieved by using the multipolar moment matching method. Several geometric variables of the sensor module are considered while developing the parametric study. The operation of the sensor module is based on the principle of the airgap flux density distribution detection by the Hall Effect IC. Therefore, the design objective is to achieve a peak flux density (PFD) greater than 0.1 T and total harmonic distortion (THD) less than 3%. To fulfill the constraint conditions, the specifications for the sensor module is achieved by using POD-DMD based reduced model. The POD-DMD based reduced model provides a platform to analyze the high number of design models very fast, with less computational burden. Finally, with the final specifications, the experimental prototype is designed and tested. Two different modes, 90° and 120° modes respectively are used to obtain the position information of the linear motor mover. The position information thus obtained are compared with that of the linear scale data, used as a reference signal. The position information obtained using the 120° mode has a standard deviation of 0.10 mm from the reference linear scale signal, whereas the 90° mode position signal shows a deviation of 0.23 mm from the reference. The deviation in the output arises due to the mechanical tolerances introduced into the specification during the manufacturing process. This provides a scope for coupling the reliability based design optimization in the design process as a future extension.

  2. Grid Based Technologies for in silico Screening and Drug Design.

    Science.gov (United States)

    Potemkin, Vladimir; Grishina, Maria

    2018-03-08

    Various techniques for rational drug design are presented in the paper. The methods are based on a substitution of antipharmacophore atoms of the molecules of training dataset by new atoms and/or group of atoms increasing the atomic bioactivity increments obtained at a SAR study. Furthermore, a design methodology based on the genetic algorithm DesPot for discrete optimization and generation of new drug candidate structures is described. Additionally, wide spectra of SAR approaches (3D/4D QSAR interior and exterior-based methods - BiS, CiS, ConGO, CoMIn, high-quality docking method - ReDock) using MERA force field and/or AlteQ quantum chemical method for correct prognosis of bioactivity and bioactive probability is described. The design methods are implemented now at www.chemosophia.com web-site for online computational services. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  3. Is function-based control room design human-centered?

    International Nuclear Information System (INIS)

    Norros, L.; Savioja, P.

    2006-01-01

    Function-based approaches to system interface design appears an appealing possibility in helping designers and operators to cope with the vast amount of information needed to control complex processes. In this paper we provide evidence of operator performance analyses showing that outcome-centered performance measures may not be sufficiently informative for design. We need analyses indicating habitual patterns of using information, operator practices. We argue that practices that portray functional orienting to the task support mastery of the process. They also create potential to make use of function-based information presentation. We see that functional design is not an absolute value. Instead, such design should support communication of the functional significance of the process information to the operators in variable situations. Hence, it should facilitate development of practices that focus to interpreting this message. Successful function-based design facilitates putting operations into their contexts and is human-centered in an extended sense: It aids making sense in the complex, dynamic and uncertain environment. (authors)

  4. Design and Numerical Study of Micropump Based on Induced Electroosmotic Flow

    Directory of Open Access Journals (Sweden)

    Kai Zhang

    2018-01-01

    Full Text Available Induced charge electroosmotic flow is a new electric driving mode. Based on the Navier–Stokes equations and the Poisson–Nernst–Planck (PNP ion transport equations, the finite volume method is adopted to calculate the equations and boundary conditions of the induced charge electroosmotic flow. In this paper, the formula of the induced zeta potential of the polarized solid surface is proposed, and a UDF program suitable for the simulation of the induced charge electroosmotic is prepared according to this theory. At the same time, on the basis of this theory, a cross micropump driven by induced charge electroosmotic flow is designed, and the voltage, electric potential, charge density, and streamline of the induced electroosmotic micropump are obtained. Studies have shown that when the cross-shaped micropump is energized, in the center of the induction electrode near the formation of a dense electric double layer, there exist four symmetrical vortices at the four corners, and they push the solution towards both outlets; it can be found that the average velocity of the solution in the cross-flow microfluidic pump is nonlinear with the applied electric field, which maybe helpful for the practical application of induced electroosmotic flow in the field of micropump.

  5. Comparison of Two Independent LIDAR-Based Pitch Control Designs

    Energy Technology Data Exchange (ETDEWEB)

    Dunne, F.; Schlipf, D.; Pao, L. Y.

    2012-08-01

    Two different lidar-based feedforward controllers have previously been designed for the NREL 5 MW wind turbine model under separate studies. Feedforward controller A uses a finite-impulse-response design, with 5 seconds of preview, and three rotating lidar measurements. Feedforward controller B uses a static-gain design, with the preview time defined by the pitch actuator dynamics, a simulation of a real nacelle-based scanning lidar system, and a lowpass filter defined by the lidar configuration. These controllers are now directly compared under the same lidar configuration, in terms of fatigue load reduction, rotor speed regulation, and power capture. The various differences in design choices are discussed and compared. We also compare frequency plots of individual pitch feedforward and collective pitch feedforward load reductions, and we see that individual pitch feedforward is effective mainly at the once-per-revolution and twice-per-revolution frequencies. We also explain how to determine the required preview time by breaking it down into separate parts, and we then compare it to the expected preview time available.

  6. Design of reactor alarm instrument based on SOPC

    International Nuclear Information System (INIS)

    Li Meng; Lu Yi; Rong Ru

    2008-01-01

    The design of embedded alarm instrument in reactors based on Nios II CPU is introduced in this paper. This design uses the SOPC technology based on the Cyclone series FPGA as a digital bench, and connects the MPU and drivers and interface of times, RS232, sdram,and etc. into a FPGA chip. It is proved that the system achieves the design goals in primary experimentation. (authors)

  7. Preliminary study of an expert system for mechanical design of a pressure vessel

    International Nuclear Information System (INIS)

    Kasmuri, N.H.; Md Som, A.

    2006-01-01

    This paper describes a preliminary study of an expert system for mechanical design of a pressure vessel. The system supports the framework for the conceptual mechanical design from the initial stages within the design procedures. ASME Boiler and Pressure Vessel Code Section VIII Division 1 were applied as a design rule. The proposed methodology facilitates the development of knowledge base acquisition, knowledge base construction and the prototype implementation. This study characterizes a knowledge base (procedure) of mechanical design of a pressure vessel subjected to internal pressure including all design parameters; i.e. temperature, shell thickness, selection of materials of constructions, stress analysis procedure, support and ancillary items. The rationalization of the mechanical design is shown in the form of a schematic flow diagram. A Kappa PC expert system shell is used as a tool to develop the prototype software. It provides graphical representation for creating objects, hierarchies and rules for knowledge base used in pressure vessel design. (Author)

  8. Reliability-based load and resistance factor design for piping: an exploratory case study

    International Nuclear Information System (INIS)

    Gupta, Abhinav; Choi, Byounghoan

    2003-01-01

    This paper presents an exploratory case study on the application of Load and Resistance Factor Design (LRFD) approach to the Section III of ASME Boiler and Pressure Vessel code for piping design. The failure criterion for defining the performance function is considered as plastic instability. Presently used design equation is calibrated by evaluating the minimum reliability levels associated with it. If the target reliability in the LRFD approach is same as that evaluated for the presently used design equation, it is shown that the total safety factors for the two design equations are identical. It is observed that the load and resistance factors are not dependent upon the diameter to thickness ratio. A sensitivity analysis is also conducted to study the variations in the load and resistance factors due to changes in (a) coefficients of variation for pressure, moment, and ultimate stress, (b) ratio of mean design pressure to mean design moment, (c) distribution types used for characterizing the random variables, and (d) statistical correlation between random variables. It is observed that characterization of random variables by log-normal distribution is reasonable. Consideration of statistical correlation between the ultimate stress and section modulus gives higher values of the load factor for pressure but lower value for the moment than the corresponding values obtained by considering the variables to be uncorrelated. Since the effect of statistical correlation on the load and resistance factors is relatively insignificant for target reliability values of practical interest, the effect of correlated variables may be neglected

  9. Design of a community-based intergenerational oral health study: "Baby Smiles".

    Science.gov (United States)

    Milgrom, Peter; Riedy, Christine A; Weinstein, Philip; Mancl, Lloyd A; Garson, Gayle; Huebner, Colleen E; Smolen, Darlene; Sutherland, Marilynn

    2013-08-06

    Rural, low-income pregnant women and their children are at high risk for poor oral health and have low utilization rates of dental care. The Baby Smiles study was designed to increase low-income pregnant women's utilization of dental care, increase young children's dental care utilization, and improve home oral health care practices. Baby Smiles was a five-year, four-site randomized intervention trial with a 2 × 2 factorial design. Four hundred participants were randomly assigned to one of four treatment arms in which they received either brief Motivational Interviewing (MI) or health education (HE) delivered during pregnancy and after the baby was born. In the prenatal study phase, the interventions were designed to encourage dental utilization during pregnancy. After childbirth, the focus was to utilize dental care for the infant by age one. The two primary outcome measures were dental utilization during pregnancy or up to two months postpartum for the mother, and preventive dental utilization by 18 months of age for the child. Medicaid claims data will be used to assess the primary outcomes. Questionnaires were administered at enrollment and 3, 9 and 18 months postpartum (study end) to assess mediating and moderating factors. This trial can help define the most effective way to provide one-on-one counseling to pregnant women and new mothers regarding visits to the dentist during pregnancy and after the child is born. It supports previous work demonstrating the potential of reducing mother-to-child transmission of Streptococcus mutans and the initiation of dental caries prevention in early childhood. ClinicalTrials.gov Identifier NCT01120041.

  10. Design-based research as a “smart” methodology for studying learning in the context of work

    DEFF Research Database (Denmark)

    Kolbæk, Ditte

    Although Design-based Research (DBR) was developed for investigating class-room training this paper discusses methodological issues when DBR is employed for investigating learning in the context of work, as it is an authentic learning environment, a real-world setting for fostering learning...... and creating usable knowledge and knowing. The purpose of this paper is to provide new perspectives on DBR regarding how to conduct DBR for studying learning from experience in the context of work. The research question is: What to consider to make DBR a smart methodology for exploring learning from experience...

  11. Using Mathematical Modeling and Set-Based Design Principles to Recommend an Existing CVL Design

    Science.gov (United States)

    2017-09-01

    MATHEMATICAL MODELING AND SET-BASED DESIGN PRINCIPLES TO RECOMMEND AN EXISTING CVL DESIGN by William H. Ehlies September 2017 Thesis Advisor...Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE...September 2017 3. REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE USING MATHEMATICAL MODELING AND SET-BASED DESIGN PRINCIPLES

  12. Reliability based Design of Coastal Structures

    DEFF Research Database (Denmark)

    Burcharth, H. F.

    2003-01-01

    Conventional design practice for coastal structures is deterministic in nature and is based on the concept of a design load which should not exceed the resistance (carrying capacity) of the structure. The design load is usually defined on a probabilistic basis as a characteristic value of the load......, for example the expectation (mean) value of the 100-year return period event. However, this selection is often made without consideration of the involved uncertainties. In most cases the resistance is defined in terms of the load that causes a certain design impact or damage to the structure...

  13. A general U-block model-based design procedure for nonlinear polynomial control systems

    Science.gov (United States)

    Zhu, Q. M.; Zhao, D. Y.; Zhang, Jianhua

    2016-10-01

    The proposition of U-model concept (in terms of 'providing concise and applicable solutions for complex problems') and a corresponding basic U-control design algorithm was originated in the first author's PhD thesis. The term of U-model appeared (not rigorously defined) for the first time in the first author's other journal paper, which established a framework for using linear polynomial control system design approaches to design nonlinear polynomial control systems (in brief, linear polynomial approaches → nonlinear polynomial plants). This paper represents the next milestone work - using linear state-space approaches to design nonlinear polynomial control systems (in brief, linear state-space approaches → nonlinear polynomial plants). The overall aim of the study is to establish a framework, defined as the U-block model, which provides a generic prototype for using linear state-space-based approaches to design the control systems with smooth nonlinear plants/processes described by polynomial models. For analysing the feasibility and effectiveness, sliding mode control design approach is selected as an exemplary case study. Numerical simulation studies provide a user-friendly step-by-step procedure for the readers/users with interest in their ad hoc applications. In formality, this is the first paper to present the U-model-oriented control system design in a formal way and to study the associated properties and theorems. The previous publications, in the main, have been algorithm-based studies and simulation demonstrations. In some sense, this paper can be treated as a landmark for the U-model-based research from intuitive/heuristic stage to rigour/formal/comprehensive studies.

  14. Visual Design Principles: An Empirical Study of Design Lore

    Science.gov (United States)

    Kimball, Miles A.

    2013-01-01

    Many books, designers, and design educators talk about visual design principles such as balance, contrast, and alignment, but with little consistency. This study uses empirical methods to explore the lore surrounding design principles. The study took the form of two stages: a quantitative literature review to determine what design principles are…

  15. A regression-based Kansei engineering system based on form feature lines for product form design

    Directory of Open Access Journals (Sweden)

    Yan Xiong

    2016-06-01

    Full Text Available When developing new products, it is important for a designer to understand users’ perceptions and develop product form with the corresponding perceptions. In order to establish the mapping between users’ perceptions and product design features effectively, in this study, we presented a regression-based Kansei engineering system based on form feature lines for product form design. First according to the characteristics of design concept representation, product form features–product form feature lines were defined. Second, Kansei words were chosen to describe image perceptions toward product samples. Then, multiple linear regression and support vector regression were used to construct the models, respectively, that predicted users’ image perceptions. Using mobile phones as experimental samples, Kansei prediction models were established based on the front view form feature lines of the samples. From the experimental results, these two predict models were of good adaptability. But in contrast to multiple linear regression, the predict performance of support vector regression model was better, and support vector regression is more suitable for form regression prediction. The results of the case showed that the proposed method provided an effective means for designers to manipulate product features as a whole, and it can optimize Kansei model and improve practical values.

  16. Design and Development of a Web Based User Interface

    OpenAIRE

    László, Magda

    2014-01-01

    The first objective of the thesis is to study the technological background of application design and more specifically the Unified Modeling Language (hereinafter UML). Due to this, the research provides deeper understanding of technical aspects of the practical part of the thesis work. The second and third objectives of this thesis are to design and develop a web application and more specifically a Web Based User Interface for Multimodal Observation and Analysis System for Social Interactions...

  17. CRBRP structural and thermal margin beyond the design base

    International Nuclear Information System (INIS)

    Strawbridge, L.E.

    1979-01-01

    Prudent margins beyond the design base have been included in the design of Clinch River Breeder Reactor Plant to further reduce the risk to the public from highly improbable occurrences. These margins include Structural Margin Beyond the Design Base to address the energetics aspects and Thermal Margin Beyond the Design Base to address the longer term thermal and radiological consequences. The assessments that led to the specification of these margins are described, along with the experimental support for those assessments. 8 refs

  18. A Distributed Feature-based Environment for Collaborative Design

    Directory of Open Access Journals (Sweden)

    Wei-Dong Li

    2003-02-01

    Full Text Available This paper presents a client/server design environment based on 3D feature-based modelling and Java technologies to enable design information to be shared efficiently among members within a design team. In this environment, design tasks and clients are organised through working sessions generated and maintained by a collaborative server. The information from an individual design client during a design process is updated and broadcast to other clients in the same session through an event-driven and call-back mechanism. The downstream manufacturing analysis modules can be wrapped as agents and plugged into the open environment to support the design activities. At the server side, a feature-feature relationship is established and maintained to filter the varied information of a working part, so as to facilitate efficient information update during the design process.

  19. Study of fault diagnosis software design for complex system based on fault tree

    International Nuclear Information System (INIS)

    Yuan Run; Li Yazhou; Wang Jianye; Hu Liqin; Wang Jiaqun; Wu Yican

    2012-01-01

    Complex systems always have high-level reliability and safety requirements, and same does their diagnosis work. As a great deal of fault tree models have been acquired during the design and operation phases, a fault diagnosis method which combines fault tree analysis with knowledge-based technology has been proposed. The prototype of fault diagnosis software has been realized and applied to mobile LIDAR system. (authors)

  20. Analysis of pre-service physics teacher skills designing simple physics experiments based technology

    Science.gov (United States)

    Susilawati; Huda, C.; Kurniawan, W.; Masturi; Khoiri, N.

    2018-03-01

    Pre-service physics teacher skill in designing simple experiment set is very important in adding understanding of student concept and practicing scientific skill in laboratory. This study describes the skills of physics students in designing simple experiments based technologicall. The experimental design stages include simple tool design and sensor modification. The research method used is descriptive method with the number of research samples 25 students and 5 variations of simple physics experimental design. Based on the results of interviews and observations obtained the results of pre-service physics teacher skill analysis in designing simple experimental physics charged technology is good. Based on observation result, pre-service physics teacher skill in designing simple experiment is good while modification and sensor application are still not good. This suggests that pre-service physics teacher still need a lot of practice and do experiments in designing physics experiments using sensor modifications. Based on the interview result, it is found that students have high enough motivation to perform laboratory activities actively and students have high curiosity to be skilled at making simple practicum tool for physics experiment.

  1. Zeroth order resonator (ZOR) based RFID antenna design

    Science.gov (United States)

    Masud, Muhammad Mubeen

    Meander-line and multi-layer antennas have been used extensively to design compact UHF radio frequency identification (RFID) tags; however the overall size reduction of meander-line antennas is limited by the amount of parasitic inductance that can be introduced by each meander-line segment, and multi-layer antennas can be too costly. In this study, a new compact antenna topology for passive UHF RFID tags based on zeroth order resonant (ZOR) design techniques is presented. The antenna consists of lossy coplanar conductors and either inter-connected inter-digital capacitor (IDC) or shunt inductor unit-cells with a ZOR frequency near the operating frequency of the antenna. Setting the ZOR frequency near the operating frequency is a key component in the design process because the unit-cells chosen for the design are inductive at the operating frequency. This makes the unit-cells very useful for antenna miniaturization. These new designs in this work have several benefits: the coplanar layout can be printed on a single layer, matching inductive loops that reduce antenna efficiency are not required and ZOR analysis can be used for the design. Finally, for validation, prototype antennas are designed, fabricated and tested.

  2. Analysis and Design of Reinforced Concrete Structures With Spring Base Isolation

    International Nuclear Information System (INIS)

    Tun Myint Aung; Tin Tin Win, Nyan Myint Kyaw

    2008-06-01

    In the study, analysis and design of four storey reinforced concrete building and it's isolations which is located in seismic zone 4. Then comparison of analysis result between fixed base condition and isolated condition of the building due to multi direction earthquake motions such as horizontal and vertical earthquake. Firstaly, static analysis is used for fixed base condition due to gravity unfactored load to design the helical spring. Secondly spectrum analysis is only utilized for horizontal earthquake and time history analysis is used for both horizontal earthquake and vertical earthquake respectively. Finally, comparison of the analysis results as forces, displacements, drifts, accelerations and shear at various levels of building are presented. The static period of fixed base is 0.4 sec. According to the base isolated concept, base isolated period is lengthened to 0.8 sec, 1 sec and 1.2sec for design earthquake level. The results which are especially compared to base isolated (1.2 sec) and fixed base building show that the displacements of base isolated is more than fixed base building but other seismic response such as acceleration of base isolated is significantly reduced compared to fixed base as well as base isloated building has capacity for reducing of member force of the structure with fixed base building

  3. NEIGHBORHOOD TEST DESIGN BASED ON HISTORIC PRECEDENTS

    Directory of Open Access Journals (Sweden)

    Besim S. Hakim

    2012-07-01

    Full Text Available There have been various attempts to emulate traditional architecture and to experiment with the form and aesthetics of building design. However, learning from precedents of urban morphology is rare. This design study is a test at the neighborhood level using the pattern of traditional courtyard housing that is prevalent in the majority of historic towns and cities of North Africa and the Middle East. The study is undertaken at five levels of design enquiry: dwelling types, dwelling groups, neighborhood segment and community center. All of which are synthesized into a full prototype neighborhood comprising of 428 dwelling units covering an area that includes circulation and the community center, of 17.6 hectares. The test demonstrates that the traditional pattern of neighborhoods that are based on the typology of the courtyard dwelling as the initial generator of urban form may be used to develop a contemporary settlement pattern that is compatible with current necessities of lifestyle, vehicular circulation,  including parking and infrastructure achieving an attractive livable environment with an overall gross density, that includes a community center, of about 24 dwelling units per hectare.

  4. Affordable Design: A Methodolgy to Implement Process-Based Manufacturing Cost into the Traditional Performance-Focused Multidisciplinary Design Optimization

    Science.gov (United States)

    Bao, Han P.; Samareh, J. A.

    2000-01-01

    The primary objective of this paper is to demonstrate the use of process-based manufacturing and assembly cost models in a traditional performance-focused multidisciplinary design and optimization process. The use of automated cost-performance analysis is an enabling technology that could bring realistic processbased manufacturing and assembly cost into multidisciplinary design and optimization. In this paper, we present a new methodology for incorporating process costing into a standard multidisciplinary design optimization process. Material, manufacturing processes, and assembly processes costs then could be used as the objective function for the optimization method. A case study involving forty-six different configurations of a simple wing is presented, indicating that a design based on performance criteria alone may not necessarily be the most affordable as far as manufacturing and assembly cost is concerned.

  5. A knowledge-based design framework for airplane conceptual and preliminary design

    Science.gov (United States)

    Anemaat, Wilhelmus A. J.

    The goal of work described herein is to develop the second generation of Advanced Aircraft Analysis (AAA) into an object-oriented structure which can be used in different environments. One such environment is the third generation of AAA with its own user interface, the other environment with the same AAA methods (i.e. the knowledge) is the AAA-AML program. AAA-AML automates the initial airplane design process using current AAA methods in combination with AMRaven methodologies for dependency tracking and knowledge management, using the TechnoSoft Adaptive Modeling Language (AML). This will lead to the following benefits: (1) Reduced design time: computer aided design methods can reduce design and development time and replace tedious hand calculations. (2) Better product through improved design: more alternative designs can be evaluated in the same time span, which can lead to improved quality. (3) Reduced design cost: due to less training and less calculation errors substantial savings in design time and related cost can be obtained. (4) Improved Efficiency: the design engineer can avoid technically correct but irrelevant calculations on incomplete or out of sync information, particularly if the process enables robust geometry earlier. Although numerous advancements in knowledge based design have been developed for detailed design, currently no such integrated knowledge based conceptual and preliminary airplane design system exists. The third generation AAA methods are tested over a ten year period on many different airplane designs. Using AAA methods will demonstrate significant time savings. The AAA-AML system will be exercised and tested using 27 existing airplanes ranging from single engine propeller, business jets, airliners, UAV's to fighters. Data for the varied sizing methods will be compared with AAA results, to validate these methods. One new design, a Light Sport Aircraft (LSA), will be developed as an exercise to use the tool for designing a new airplane

  6. The-Abstraction-Hierarchy-based Mobile PC Display Design for NPP Maintenance

    International Nuclear Information System (INIS)

    Kim, In; Kim, Bo Gyung; Seong, Poong Hyun; Ha, Jun Su

    2010-01-01

    Recently, the importance of effective maintenance in nuclear power plants (NPPs) has been emphasized and research into effective maintenance by adopting mobile maintenance aids (MMAs) have been attempted. For improved and effective use of an MMA display design method based on abstraction hierarchy (AH) is proposed and its design considerations are discussed in this study. Six levels of abstraction hierarchy are proposed in this paper to classify the maintenance information. By classifying and organizing maintenance information using AH, maintenance information can be used effectively by users with either high or low levels of expertise. When information classification has been finished, the information for MMA design is selected and designed. With the considerations of MMA design analysis and guidelines, AH-based MMA is designed for the maintenance tasks. An experiment is conducted using the AH-based MMA in order to estimate the effectiveness of the proposed method for the maintenance tasks and to identify design considerations to enhance the proposed MMAs. The result indicated that an AH-based manual was more effective than a conventional manual in terms of task completion time and number of errors. The workload for the AH-based manual was estimated less than the conventional manual for subjects with low level of expertise. As the level of expertise increases, subjects tended to follow more abstract information while the number of navigations decreased. It is believed that when mobile devices become pervasive in NPP maintenance fields, AH-model applied MMAs can be used as an effective maintenance supporting tool

  7. Making the case for evidence-based design in healthcare: a descriptive case study of organizational decision making.

    Science.gov (United States)

    Shoemaker, Lorie K; Kazley, Abby Swanson; White, Andrea

    2010-01-01

    The aim of this study was to describe the organizational decision-making process used in the selection of evidence-based design (EBD) concepts, the criteria used to make these decisions, and the extent to which leadership style may have influenced the decision-making process. Five research questions were formulated to frame the direction of this study, including: (1) How did healthcare leaders learn of innovations in design? (2) How did healthcare leaders make decisions in the selection of healthcare design concepts? (3) What criteria did healthcare leaders use in the decision-making process? (4) How did healthcare leaders consider input from the staff in design decisions? and (5) To what extent did the leadership style of administrators affect the outcomes of the decision-making process? Current issues affecting healthcare in the community led the principal investigator's organization to undertake an ambitious facilities expansion project. As part of its planning process, the organization learned of EBD principles that seemingly had a positive impact on patient care and safety and staff working conditions. Although promising, a paucity of empirical research addressed the cost/benefit of incorporating many EBD concepts into one hospital setting, and there was no research that articulated the organizational decision-making process used by healthcare administrators when considering the use of EBD in expansion projects. A mixed-method, descriptive, qualitative, single-case study and quantitative design were used to address the five research questions. The Systems Research Organizing Model provided the theoretical framework. A variety of data collection methods was used, including interviews of key respondents, the review of documentary evidence, and the Multifactor Leadership Questionnaire. A participatory process was used throughout the design decision phases, involving staff at all levels of the organization. The Internet and architects facilitated learning about

  8. Computer-based Creativity Enhanced Conceptual Design Model for Non-routine Design of Mechanical Systems

    Institute of Scientific and Technical Information of China (English)

    LI Yutong; WANG Yuxin; DUFFY Alex H B

    2014-01-01

    Computer-based conceptual design for routine design has made great strides, yet non-routine design has not been given due attention, and it is still poorly automated. Considering that the function-behavior-structure(FBS) model is widely used for modeling the conceptual design process, a computer-based creativity enhanced conceptual design model(CECD) for non-routine design of mechanical systems is presented. In the model, the leaf functions in the FBS model are decomposed into and represented with fine-grain basic operation actions(BOA), and the corresponding BOA set in the function domain is then constructed. Choosing building blocks from the database, and expressing their multiple functions with BOAs, the BOA set in the structure domain is formed. Through rule-based dynamic partition of the BOA set in the function domain, many variants of regenerated functional schemes are generated. For enhancing the capability to introduce new design variables into the conceptual design process, and dig out more innovative physical structure schemes, the indirect function-structure matching strategy based on reconstructing the combined structure schemes is adopted. By adjusting the tightness of the partition rules and the granularity of the divided BOA subsets, and making full use of the main function and secondary functions of each basic structure in the process of reconstructing of the physical structures, new design variables and variants are introduced into the physical structure scheme reconstructing process, and a great number of simpler physical structure schemes to accomplish the overall function organically are figured out. The creativity enhanced conceptual design model presented has a dominant capability in introducing new deign variables in function domain and digging out simpler physical structures to accomplish the overall function, therefore it can be utilized to solve non-routine conceptual design problem.

  9. Computer-based creativity enhanced conceptual design model for non-routine design of mechanical systems

    Science.gov (United States)

    Li, Yutong; Wang, Yuxin; Duffy, Alex H. B.

    2014-11-01

    Computer-based conceptual design for routine design has made great strides, yet non-routine design has not been given due attention, and it is still poorly automated. Considering that the function-behavior-structure(FBS) model is widely used for modeling the conceptual design process, a computer-based creativity enhanced conceptual design model(CECD) for non-routine design of mechanical systems is presented. In the model, the leaf functions in the FBS model are decomposed into and represented with fine-grain basic operation actions(BOA), and the corresponding BOA set in the function domain is then constructed. Choosing building blocks from the database, and expressing their multiple functions with BOAs, the BOA set in the structure domain is formed. Through rule-based dynamic partition of the BOA set in the function domain, many variants of regenerated functional schemes are generated. For enhancing the capability to introduce new design variables into the conceptual design process, and dig out more innovative physical structure schemes, the indirect function-structure matching strategy based on reconstructing the combined structure schemes is adopted. By adjusting the tightness of the partition rules and the granularity of the divided BOA subsets, and making full use of the main function and secondary functions of each basic structure in the process of reconstructing of the physical structures, new design variables and variants are introduced into the physical structure scheme reconstructing process, and a great number of simpler physical structure schemes to accomplish the overall function organically are figured out. The creativity enhanced conceptual design model presented has a dominant capability in introducing new deign variables in function domain and digging out simpler physical structures to accomplish the overall function, therefore it can be utilized to solve non-routine conceptual design problem.

  10. Design of an Emulsion-based Personal Detergent through a Model-based Chemical Product Design Methodology

    DEFF Research Database (Denmark)

    Mattei, Michele; Hill, Michael; Kontogeorgis, Georgios

    2013-01-01

    An extended systematic methodology for the design of emulsion-based Chemical products is presented. The methodology consists of a model-based framework involving seven sequential hierarchical steps: starting with the identification of the needs to be satisfied by the product and then adding one-b...... to obtain one or more candidate formulations. A conceptual casestudy representing a personal detergent is presented to highlight the methodology....

  11. Design of an Emulsion-based Personal Detergent through a Model-based Chemical Product Design Methodology

    DEFF Research Database (Denmark)

    Mattei, Michele; Hill, Michael; Kontogeorgis, Georgios

    2013-01-01

    An extended systematic methodology for the design of emulsion-based Chemical products is presented. The methodology consists of a model-based framework involving seven sequential hierarchical steps: starting with the identification of the needs to be satisfied by the product and then adding one...... to obtain one or more candidate formulations. A conceptual casestudy representing a personal detergent is presented to highlight the methodology....

  12. Design, Implementation, and Study Protocol of a Kindergarten-Based Health Promotion Intervention

    Directory of Open Access Journals (Sweden)

    Susanne Kobel

    2017-01-01

    Full Text Available Inactivity and an unhealthy diet amongst others have led to an increased prevalence of overweight and obesity even in young children. Since most health behaviours develop during childhood health promotion has to start early. The setting kindergarten has been shown as ideal for such interventions. “Join the Healthy Boat” is a kindergarten-based health promotion programme with a cluster-randomised study focussing on increased physical activity, reduced screen media use, and sugar-sweetened beverages, as well as a higher fruit and vegetable intake. Intervention and materials were developed using Bartholomew’s Intervention Mapping approach considering Bandura’s social-cognitive theory and Bronfenbrenner’s ecological framework for human development. The programme is distributed using a train-the-trainer approach and currently implemented in 618 kindergartens. The effectiveness of this one-year intervention with an intervention and a control group will be examined in 62 kindergartens using standardised protocols, materials, and tools for outcome and process evaluation. A sample of 1021 children and their parents provided consent and participated in the intervention. Results of this study are awaited to give a better understanding of health behaviours in early childhood and to identify strategies for effective health promotion. The current paper describes development and design of the intervention and its implementation and planned evaluation. Trial Registration. The study is registered at the German Clinical Trials Register (DRKS, Freiburg University, Germany, ID: DRKS00010089.

  13. Conceptual study of advanced PWR core design

    International Nuclear Information System (INIS)

    Kim, Young Jin; Chang, Moon Hee; Kim, Keung Ku; Joo, Hyung Kuk; Kim, Young Il; Noh, Jae Man; Hwang, Dae Hyun; Kim, Taek Kyum; Yoo, Yon Jong.

    1997-09-01

    The purpose of this project is for developing and verifying the core design concepts with enhanced safety and economy, and associated methodologies for core analyses. From the study of the sate-of-art of foreign advanced reactor cores, we developed core concepts such as soluble boron free, high convertible and enhanced safety core loaded semi-tight lattice hexagonal fuel assemblies. To analyze this hexagonal core, we have developed and verified some neutronic and T/H analysis methodologies. HELIOS code was adopted as the assembly code and HEXFEM code was developed for hexagonal core analysis. Based on experimental data in hexagonal lattices and the COBRA-IV-I code, we developed a thermal-hydraulic analysis code for hexagonal lattices. Using the core analysis code systems developed in this project, we designed a 600 MWe core and studied the feasibility of the core concepts. Two additional scopes were performed in this project : study on the operational strategies of soluble boron free core and conceptual design of large scale passive core. By using the axial BP zoning concept and suitable design of control rods, this project showed that it was possible to design a soluble boron free core in 600 MWe PWR. The results of large scale core design showed that passive concepts and daily load follow operation could be practiced. (author). 15 refs., 52 tabs., 101 figs

  14. Conceptual study of advanced PWR core design

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Jin; Chang, Moon Hee; Kim, Keung Ku; Joo, Hyung Kuk; Kim, Young Il; Noh, Jae Man; Hwang, Dae Hyun; Kim, Taek Kyum; Yoo, Yon Jong

    1997-09-01

    The purpose of this project is for developing and verifying the core design concepts with enhanced safety and economy, and associated methodologies for core analyses. From the study of the sate-of-art of foreign advanced reactor cores, we developed core concepts such as soluble boron free, high convertible and enhanced safety core loaded semi-tight lattice hexagonal fuel assemblies. To analyze this hexagonal core, we have developed and verified some neutronic and T/H analysis methodologies. HELIOS code was adopted as the assembly code and HEXFEM code was developed for hexagonal core analysis. Based on experimental data in hexagonal lattices and the COBRA-IV-I code, we developed a thermal-hydraulic analysis code for hexagonal lattices. Using the core analysis code systems developed in this project, we designed a 600 MWe core and studied the feasibility of the core concepts. Two additional scopes were performed in this project : study on the operational strategies of soluble boron free core and conceptual design of large scale passive core. By using the axial BP zoning concept and suitable design of control rods, this project showed that it was possible to design a soluble boron free core in 600 MWe PWR. The results of large scale core design showed that passive concepts and daily load follow operation could be practiced. (author). 15 refs., 52 tabs., 101 figs.

  15. Simulation and Experimental Studies on Grain Selection and Structure Design of the Spiral Selector for Casting Single Crystal Ni-Based Superalloy.

    Science.gov (United States)

    Zhang, Hang; Xu, Qingyan

    2017-10-27

    Grain selection is an important process in single crystal turbine blades manufacturing. Selector structure is a control factor of grain selection, as well as directional solidification (DS). In this study, the grain selection and structure design of the spiral selector were investigated through experimentation and simulation. A heat transfer model and a 3D microstructure growth model were established based on the Cellular automaton-Finite difference (CA-FD) method for the grain selector. Consequently, the temperature field, the microstructure and the grain orientation distribution were simulated and further verified. The average error of the temperature result was less than 1.5%. The grain selection mechanisms were further analyzed and validated through simulations. The structural design specifications of the selector were suggested based on the two grain selection effects. The structural parameters of the spiral selector, namely, the spiral tunnel diameter ( d w ), the spiral pitch ( h b ) and the spiral diameter ( h s ), were studied and the design criteria of these parameters were proposed. The experimental and simulation results demonstrated that the improved selector could accurately and efficiently produce a single crystal structure.

  16. Examining Teacher Talk in an Engineering Design-Based Science Curricular Unit

    Science.gov (United States)

    Aranda, Maurina L.; Lie, Richard; Selcen Guzey, S.; Makarsu, Murat; Johnston, Amanda; Moore, Tamara J.

    2018-03-01

    Recent science education reforms highlight the importance for teachers to implement effective instructional practices that promote student learning of science and engineering content and their practices. Effective classroom discussion has been shown to support the learning of science, but work is needed to examine teachers' enactment of engineering design-based science curricula by focusing on the content, complexity, structure, and orchestration of classroom discussions. In the present study, we explored teacher-student talk with respect to science in a middle school curriculum focused on genetics and genetic engineering. Our study was guided by the following major research question: What are the similarities and differences in teacher talk moves that occurred within an engineering design-based science unit enacted by two teachers? Through qualitative and quantitative approaches, we found that there were clear differences in two teachers' use of questioning strategies and presentation of new knowledge that affected the level of student involvement in classroom discourse and the richness and details of student contributions to the conversations. We also found that the verbal explanations of science content differed between two teachers. Collectively, the findings in this study demonstrate that although the teachers worked together to design an engineering designed-based science curriculum unit, their use of different discussion strategies and patterns, and interactions with students differed to affect classroom discourse.

  17. Conceptual design study of Fusion Experimental Reactor (FY87FER)

    International Nuclear Information System (INIS)

    1988-05-01

    The design study of Fusion Experimental Reactor(FER) which has been proposed to be the next step fusion device has been conducted by JAERI Reactor System Laboratory since 1982 and by FER design team since 1984. This is the final report of the FER design team program and describes the results obtained in FY1987 (partially in FY1986) activities. The contents of this report consist of the reference design which is based on the guideline in FY1986 by the Subcomitees set up in Nuclear Fusion Council of Atomic Energy Commission of Japan, the Low-Physics-Risk reactor design for achieving physics mission more reliably and the system study of FER design candidates including above two designs. (author)

  18. Interactive Reliability-Based Optimal Design

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle; Siemaszko, A.

    1994-01-01

    Interactive design/optimization of large, complex structural systems is considered. The objective function is assumed to model the expected costs. The constraints are reliability-based and/or related to deterministic code requirements. Solution of this optimization problem is divided in four main...... tasks, namely finite element analyses, sensitivity analyses, reliability analyses and application of an optimization algorithm. In the paper it is shown how these four tasks can be linked effectively and how existing information on design variables, Lagrange multipliers and the Hessian matrix can...

  19. Making Theory Come Alive through Practice-based Design Research

    DEFF Research Database (Denmark)

    Markussen, Thomas; Knutz, Eva; Rind Christensen, Poul

    The aim of this paper is to demonstrate how practice-based design research is able not only to challenge, but also to push toward further development of some of the basic assumpstions in emotion theories as used within design research. In so doing, we wish to increase knolwedge on a central...... epistemological question for design research, namely how practice-based design research can be a vehicle for the construction of new theory for design research....

  20. Optimization of the Conical Angle Design in Conical Implant-Abutment Connections: A Pilot Study Based on the Finite Element Method.

    Science.gov (United States)

    Yao, Kuang-Ta; Chen, Chen-Sheng; Cheng, Cheng-Kung; Fang, Hsu-Wei; Huang, Chang-Hung; Kao, Hung-Chan; Hsu, Ming-Lun

    2018-02-01

    Conical implant-abutment connections are popular for their excellent connection stability, which is attributable to frictional resistance in the connection. However, conical angles, the inherent design parameter of conical connections, exert opposing effects on 2 influencing factors of the connection stability: frictional resistance and abutment rigidity. This pilot study employed an optimization approach through the finite element method to obtain an optimal conical angle for the highest connection stability in an Ankylos-based conical connection system. A nonlinear 3-dimensional finite element parametric model was developed according to the geometry of the Ankylos system (conical half angle = 5.7°) by using the ANSYS 11.0 software. Optimization algorithms were conducted to obtain the optimal conical half angle and achieve the minimal value of maximum von Mises stress in the abutment, which represents the highest connection stability. The optimal conical half angle obtained was 10.1°. Compared with the original design (5.7°), the optimal design demonstrated an increased rigidity of abutment (36.4%) and implant (25.5%), a decreased microgap at the implant-abutment interface (62.3%), a decreased contact pressure (37.9%) with a more uniform stress distribution in the connection, and a decreased stress in the cortical bone (4.5%). In conclusion, the methodology of design optimization to determine the optimal conical angle of the Ankylos-based system is feasible. Because of the heterogeneity of different systems, more studies should be conducted to define the optimal conical angle in various conical connection designs.

  1. Scenarios, personas and user stories from design ethnography: Evidence-based design representations of communicable disease investigations

    Science.gov (United States)

    Turner, Anne M; Reeder, Blaine; Ramey, Judith

    2014-01-01

    Purpose Despite years of effort and millions of dollars spent to create a unified electronic communicable disease reporting systems, the goal remains elusive. A major barrier has been a lack of understanding by system designers of communicable disease (CD) work and the public health workers who perform this work. This study reports on the application of User Center Design representations, traditionally used for improving interface design, to translate the complex CD work identified through ethnographic studies to guide designers and developers of CD systems. The purpose of this work is to: (1) better understand public health practitioners and their information workflow with respect to communicable disease (CD) monitoring and control at a local health department, and (2) to develop evidence-based design representations that model this CD work to inform the design of future disease surveillance systems. Methods We performed extensive onsite semi-structured interviews, targeted work shadowing and a focus group to characterize local health department communicable disease workflow. Informed by principles of design ethnography and user-centered design (UCD) we created persona, scenarios and user stories to accurately represent the user to system designers. Results We sought to convey to designers the key findings from ethnographic studies: 1) that public health CD work is mobile and episodic, in contrast to current CD reporting systems, which are stationary and fixed 2) health department efforts are focused on CD investigation and response rather than reporting and 3) current CD information systems must conform to PH workflow to ensure their usefulness. In an effort to illustrate our findings to designers, we developed three contemporary design-support representations: persona, scenario, and user story. Conclusions Through application of user centered design principles, we were able to create design representations that illustrate complex public health communicable

  2. Constructivism Based Learning: Design and Practice

    Directory of Open Access Journals (Sweden)

    Lia Kurniawati

    2016-06-01

    Full Text Available Abstract One of many problems in the madrasahs is that learning processes less-involve students actively (teacher-centered, thus, it affects to the improvement of learning outcomes and quality of the graduates. The purposes of this study are , firstly, to analyze what type of constructivism learning models, which can be developed to overcome madrasahs’ problems. Secondly, how to design and implement a learning plan based on the developed constructivism models. This research was conducted at Private Islamic Elementary School  (Madrasah Ad-Diyanah Ciputat, South Tangerang. Research method used in this study is descriptive-qualitative research. The results showed that the active learning models based on constructivism are suitable to be developed in the Madarasah, which were the models of Problem Based Learning (PBM, Realistic Learning, Inquiry Learning and Thematic Learning and also how the development of the learning processes from the lesson plans to the learning implementation showed a paradigm shifting from teacher-centered to student-centered. Abstrak Salah satu permasalahan di madrasah-madrasah adalah proses pembelajaran yang kurang melibatkan siswa secara aktif (berpusat pada guru, sehingga hal ini mengakibatkan pada peningkatan hasil belajar dan kualitas lulusan. Tujuan dari penelitian ini adalah, pertama, untuk menganalisis jenis model pembelajaran konstruktivisme apa yang dapat dikembangkan untuk mengatasi permasalahan di madrasah. Ke dua, bagaimana merancang dan melaksanakan rencana pembelajaran berdasarkan model konstruktivisme yang dikembangkan. Penelitian ini dilaksanakan di Sekolah Dasar Swasta (madrasah Ad-Diayanah Ciputat, Tangerang Selatan. Metode penelitian yang digunakan adalah metode deskriptif-kualitatif. Hasil penelitian menunjukkan bahwa model pembelajaran aktif yang berbasis konstruktivisme sesuai untuk dikembangkan di madrasah, yakni model pembelajaran Problem Based Learning (PBL, Pembelajaran Realistis, Pembelajaran

  3. Research on performance-based seismic design criteria

    Institute of Scientific and Technical Information of China (English)

    谢礼立; 马玉宏

    2002-01-01

    The seismic design criterion adopted in the existing seismic design codes is reviewed. It is pointed out that the presently used seismic design criterion is not satisfied with the requirements of nowadays social and economic development. A new performance-based seismic design criterion that is composed of three components is presented in this paper. It can not only effectively control the economic losses and casualty, but also ensure the building(s function in proper operation during earthquakes. The three components are: classification of seismic design for buildings, determination of seismic design intensity and/or seismic design ground motion for controlling seismic economic losses and casualties, and determination of the importance factors in terms of service periods of buildings. For controlling the seismic human losses, the idea of socially acceptable casualty level is presented and the (Optimal Economic Decision Model( and (Optimal Safe Decision Model( are established. Finally, a new method is recommended for calculating the importance factors of structures by adjusting structures service period on the base of more important structure with longer service period than the conventional ones. Therefore, the more important structure with longer service periods will be designed for higher seismic loads, in case the exceedance probability of seismic hazard in different service period is same.

  4. Design study of blanket structure based on a water-cooled solid breeder for DEMO

    Energy Technology Data Exchange (ETDEWEB)

    Someya, Youji; Tobita, Kenji; Utoh, Hiroyasu; Tokunaga, Shinji; Hoshino, Kazuo; Asakura, Nobuyuki; Nakamura, Makoto; Sakamoto, Yoshiteru

    2015-10-15

    Highlights: • Neutronics design of a water-cooled solid mixed breeder blanket was presented. • The blanket concept achieves a self-sufficient supply of tritium by neutronics analysis. • The overall outlet coolant temperature was 321 °C, which is in the acceptable range. - Abstract: Blanket concept with a simplified interior for mass production has been developed using a mixed bed of Li{sub 2}TiO{sub 3} and Be{sub 12}Ti pebbles, coolant conditions of 15.5 MPa and 290–325 °C and cooling pipes without any partitions. Considering the continuity with the ITER test blanket module option of Japan and the engineering feasibility in its fabrication, our design study focused on a water-cooled solid breeding blanket using the mixed pebbles bed. Herein, we propose blanket segmentation corresponding to the shape and dimension of the blanket and routing of the coolant flow. Moreover, we estimate the overall tritium breeding ratio (TBR) with a torus configuration, based on the segmentation using three-dimensional (3D) Monte Carlo N-particle calculations. As a result, the overall TBR is 1.15. Our 3D neutronics analysis for TBR ensures that the blanket concept can achieve a self-sufficient supply of tritium.

  5. Model-Checking Driven Design of QoS-Based Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Zhi Chen

    2015-01-01

    Full Text Available Accurate and reliable routing protocols with Quality of Service (QoS support determine the mission-critical application efficiency in WSNs. This paper proposes a model-checking design driven framework for designing the QoS-based routing protocols of WSNs, which involves the light-weight design process, the timed automata model, and the alternative QoS verification properties. The accurate feedback of continually model checking in the iterative design process effectively stimulates the parameter tuning of the protocols. We demonstrate the straightforward and modular characteristics of the proposed framework in designing a prototype QoS-based routing protocol. The prototype study shows that the model-checking design framework may complement other design methods and ensure the QoS implementation of the QoS-based routing protocol design for WSNs.

  6. A web-based computer-tailored smoking prevention programme for primary school children: intervention design and study protocol

    Science.gov (United States)

    2012-01-01

    Background Although the number of smokers has declined in the last decade, smoking is still a major health problem among youngsters and adolescents. For this reason, there is a need for effective smoking prevention programmes targeting primary school children. A web-based computer-tailored feedback programme may be an effective intervention to stimulate youngsters not to start smoking, and increase their knowledge about the adverse effects of smoking and their attitudes and self-efficacy regarding non-smoking. Methods & design This paper describes the development and evaluation protocol of a web-based out-of-school smoking prevention programme for primary school children (age 10-13 years) entitled ‘Fun without Smokes’. It is a transformation of a postal mailed intervention to a web-based intervention. Besides this transformation the effects of prompts will be examined. This web-based intervention will be evaluated in a 2-year cluster randomised controlled trial (c-RCT) with three study arms. An intervention and intervention + prompt condition will be evaluated for effects on smoking behaviour, compared with a no information control condition. Information about pupils’ smoking status and other factors related to smoking will be obtained using a web-based questionnaire. After completing the questionnaire pupils in both intervention conditions will receive three computer-tailored feedback letters in their personal e-mail box. Attitudes, social influences and self-efficacy expectations will be the content of these personalised feedback letters. Pupils in the intervention + prompt condition will - in addition to the personalised feedback letters - receive e-mail and SMS messages prompting them to revisit the ‘Fun without Smokes’ website. The main outcome measures will be ever smoking and the utilisation of the ‘Fun without Smokes’ website. Measurements will be carried out at baseline, 12 months and 24 months of follow-up. Discussion The present study

  7. A web-based computer-tailored smoking prevention programme for primary school children: intervention design and study protocol

    Directory of Open Access Journals (Sweden)

    Cremers Henricus-Paul

    2012-06-01

    Full Text Available Abstract Background Although the number of smokers has declined in the last decade, smoking is still a major health problem among youngsters and adolescents. For this reason, there is a need for effective smoking prevention programmes targeting primary school children. A web-based computer-tailored feedback programme may be an effective intervention to stimulate youngsters not to start smoking, and increase their knowledge about the adverse effects of smoking and their attitudes and self-efficacy regarding non-smoking. Methods & design This paper describes the development and evaluation protocol of a web-based out-of-school smoking prevention programme for primary school children (age 10-13 years entitled ‘Fun without Smokes’. It is a transformation of a postal mailed intervention to a web-based intervention. Besides this transformation the effects of prompts will be examined. This web-based intervention will be evaluated in a 2-year cluster randomised controlled trial (c-RCT with three study arms. An intervention and intervention + prompt condition will be evaluated for effects on smoking behaviour, compared with a no information control condition. Information about pupils’ smoking status and other factors related to smoking will be obtained using a web-based questionnaire. After completing the questionnaire pupils in both intervention conditions will receive three computer-tailored feedback letters in their personal e-mail box. Attitudes, social influences and self-efficacy expectations will be the content of these personalised feedback letters. Pupils in the intervention + prompt condition will - in addition to the personalised feedback letters - receive e-mail and SMS messages prompting them to revisit the ‘Fun without Smokes’ website. The main outcome measures will be ever smoking and the utilisation of the ‘Fun without Smokes’ website. Measurements will be carried out at baseline, 12 months and 24 months of follow

  8. Design Criteria Based on Aesthetic Considerations

    DEFF Research Database (Denmark)

    Thomsen, Bente Dahl

    2009-01-01

    Aesthetic criteria for designs are often debated in a very subjective manner which makes it difficult to reach consensus. In order to have a more rational and transparent process, in particular in industrial design, we propose a procedure based on Baumgarten's aesthetic considerations and Thommesen......'s dividing of a form into form elements. The procedure has been tested in student projects....

  9. Designing, implementing and evaluating an online problem-based learning (PBL) environment--a pilot study.

    Science.gov (United States)

    Ng, Manwa L; Bridges, Susan; Law, Sam Po; Whitehill, Tara

    2014-01-01

    Problem-based learning (PBL) has been shown to be effective for promoting student competencies in self-directed and collaborative learning, critical thinking, self-reflection and tackling novel situations. However, the need for face-to-face interactions at the same place and time severely limits the potential of traditional PBL. The requirements of space and for meeting at a specific location at the same time create timetabling difficulties. Such limitations need to be tackled before all potentials of PBL learning can be realized. The present study aimed at designing and implementing an online PBL environment for undergraduate speech/language pathology students, and assessing the associated pedagogical effectiveness. A group of eight PBL students were randomly selected to participate in the study. They underwent 4 weeks of online PBL using Adobe Connect. Upon completion of the experiment, they were assessed via a self-reported questionnaire and quantitative comparison with traditional PBL students based on the same written assignment. The questionnaire revealed that all participating students enjoyed online PBL, without any perceived negative effects on learning. Online PBL unanimously saved the students travel time to and from school. Statistical analysis indicated no significant difference in assignment grades between the online and traditional PBL groups, indicating that online PBL learning appears to be similarly effective as traditional face-to-face PBL learning.

  10. A model-based framework for design of intensified enzyme-based processes

    DEFF Research Database (Denmark)

    Román-Martinez, Alicia

    This thesis presents a generic and systematic model-based framework to design intensified enzyme-based processes. The development of the presented methodology was motivated by the needs of the bio-based industry for a more systematic approach to achieve intensification in its production plants...... in enzyme-based processes which have found significant application in the pharmaceutical, food, and renewable fuels sector. The framework uses model-based strategies for (bio)-chemical process design and optimization, including the use of a superstructure to generate all potential reaction......(s)-separation(s) options according to a desired performance criteria and a generic mathematical model represented by the superstructure to derive the specific models corresponding to a specific process option. In principle, three methods of intensification of bioprocess are considered in this thesis: 1. enzymatic one...

  11. Paired split-plot designs of multireader multicase studies.

    Science.gov (United States)

    Chen, Weijie; Gong, Qi; Gallas, Brandon D

    2018-07-01

    The widely used multireader multicase ROC study design for comparing imaging modalities is the fully crossed (FC) design: every reader reads every case of both modalities. We investigate paired split-plot (PSP) designs that may allow for reduced cost and increased flexibility compared with the FC design. In the PSP design, case images from two modalities are read by the same readers, thereby the readings are paired across modalities. However, within each modality, not every reader reads every case. Instead, both the readers and the cases are partitioned into a fixed number of groups and each group of readers reads its own group of cases-a split-plot design. Using a [Formula: see text]-statistic based variance analysis for AUC (i.e., area under the ROC curve), we show analytically that precision can be gained by the PSP design as compared with the FC design with the same number of readers and readings. Equivalently, we show that the PSP design can achieve the same statistical power as the FC design with a reduced number of readings. The trade-off for the increased precision in the PSP design is the cost of collecting a larger number of truth-verified patient cases than the FC design. This means that one can trade-off between different sources of cost and choose a least burdensome design. We provide a validation study to show the iMRMC software can be reliably used for analyzing data from both FC and PSP designs. Finally, we demonstrate the advantages of the PSP design with a reader study comparing full-field digital mammography with screen-film mammography.

  12. A Comparison of Different Teaching Designs of "Acids and Bases" Subject

    Science.gov (United States)

    Ültay, Neslihan; Çalik, Muammer

    2016-01-01

    Inability to link the acid-base concepts with daily life phenomena (as contexts) highlights the need for further research on the context-based acid-base chemistry. In this vein, the aim of this study is to investigate the effects of different teaching designs (REACT strategy, 5Es learning model and traditional (existing) instruction) relevant with…

  13. A Capstone Wiki Knowledge Base: A Case Study of an Online Tool Designed to Promote Life-Long Learning through Engineering Literature Research

    Science.gov (United States)

    Clarke, James B.; Coyle, James R.

    2011-01-01

    This article reports the results of a case study in which an experimental wiki knowledge base was designed, developed, and tested by the Brill Science Library at Miami University for an undergraduate engineering senior capstone project. The wiki knowledge base was created to determine if the science library could enhance the engineering literature…

  14. Computer-Aided Test Flow in Core-Based Design

    NARCIS (Netherlands)

    Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

    2000-01-01

    This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of

  15. Demonstration of risk-based decision analysis in remedial alternative selection and design

    International Nuclear Information System (INIS)

    Evans, E.K.; Duffield, G.M.; Massmann, J.W.; Freeze, R.A.; Stephenson, D.E.

    1993-01-01

    This study demonstrates the use of risk-based decision analysis (Massmann and Freeze 1987a, 1987b) in the selection and design of an engineering alternative for groundwater remediation at a waste site at the Savannah River Site, a US Department of Energy facility in South Carolina. The investigation focuses on the remediation and closure of the H-Area Seepage Basins, an inactive disposal site that formerly received effluent water from a nearby production facility. A previous study by Duffield et al. (1992), which used risk-based decision analysis to screen a number of ground-water remediation alternatives under consideration for this site, indicated that the most attractive remedial option is ground-water extraction by wells coupled with surface water discharge of treated effluent. The aim of the present study is to demonstrate the iterative use of risk-based decision analysis throughout the design of a particular remedial alternative. In this study, we consider the interaction between two episodes of aquifer testing over a 6-year period and the refinement of a remedial extraction well system design. Using a three-dimensional ground-water flow model, this study employs (1) geostatistics and Monte Carlo techniques to simulate hydraulic conductivity as a stochastic process and (2) Bayesian updating and conditional simulation to investigate multiple phases of aquifer testing. In our evaluation of a remedial alternative, we compute probabilistic costs associated with the failure of an alternative to completely capture a simulated contaminant plume. The results of this study demonstrate the utility of risk-based decision analysis as a tool for improving the design of a remedial alternative through the course of phased data collection at a remedial site

  16. Performance-based plastic design of earthquake resistant reinforced concrete moment frames

    Science.gov (United States)

    Liao, Wen-Cheng

    Performance-Based Plastic Design (PBPD) method has been recently developed to achieve enhanced performance of earthquake resistant structures. The design concept uses pre-selected target drift and yield mechanism as performance criteria. The design base shear for selected hazard level is determined by equating the work needed to push the structure monotonically up to the target drift to the corresponding energy demand of an equivalent SDOF oscillator. This study presents development of the PBPD approach as applied to reinforced concrete special moment frame (RC SMF) structures. RC structures present special challenge because of their complex and degrading ("pinched") hysteretic behavior. In order to account for the degrading hysteretic behavior the 1-EMA 440 C2 factor approach was used in the process of determining the design base shear. Four baseline RC SMF (4, 8, 12 and 20-story) as used in the FEMA P695 were selected for this study. Those frames were redesigned by the PBPD approach. The baseline frames and the PBPD frames were subjected to extensive inelastic pushover and time-history analyses. The PBPD frames showed much improved response meeting all desired performance objectives, including the intended yield mechanisms and the target drifts. On the contrary, the baseline frames experienced large story drifts due to flexural yielding of the columns. The work-energy equation to determine design base shear can also be used to estimate seismic demands, called the energy spectrum method. In this approach the skeleton force-displacement (capacity) curve of the structure is converted into energy-displacement plot (Ec) which is superimposed over the corresponding energy demand plot ( Ed) for the specified hazard level to determine the expected peak displacement demands. In summary, this study shows that the PBPD approach can be successfully applied to RC moment frame structures as well, and that the responses of the example moment frames were much improved over those

  17. Computation-based virtual screening for designing novel antimalarial drugs by targeting falcipain-III: a structure-based drug designing approach.

    Science.gov (United States)

    Kesharwani, Rajesh Kumar; Singh, Durg Vijay; Misra, Krishna

    2013-01-01

    Cysteine proteases (falcipains), a papain-family of enzymes of Plasmodium falciparum, are responsible for haemoglobin degradation and thus necessary for its survival during asexual life cycle phase inside the human red blood cells while remaining non-functional for the human body. Therefore, these can act as potential targets for designing antimalarial drugs. The P. falciparum cysteine proteases, falcipain-II and falcipain- III are the enzymes which initiate the haemoglobin degradation, therefore, have been selected as targets. In the present study, we have designed new leupeptin analogues and subjected to virtual screening using Glide at the active site cavity of falcipain-II and falcipain-III to select the best docked analogues on the basis of Glide score and also compare with the result of AutoDock. The proposed analogues can be synthesized and tested in vivo as future potent antimalarial drugs. Protein falcipain-II and falcipain-III together with bounds inhibitors epoxysuccinate E64 (E64) and leupeptin respectively were retrieved from protein data bank (PDB) and latter leupeptin was used as lead molecule to design new analogues by using Ligbuilder software and refined the molecules on the basis of Lipinski rule of five and fitness score parameters. All the designed leupeptin analogues were screened via docking simulation at the active site cavity of falcipain-II and falcipain-III by using Glide software and AutoDock. The 104 new leupeptin-based antimalarial ligands were designed using structure-based drug designing approach with the help of Ligbuilder and subjected for virtual screening via docking simulation method against falcipain-II and falcipain-III receptor proteins. The Glide docking results suggest that the ligands namely result_037 shows good binding and other two, result_044 and result_042 show nearly similar binding than naturally occurring PDB bound ligand E64 against falcipain-II and in case of falcipain-III, 15 designed leupeptin analogues having

  18. Methodology for cloud-based design of robots

    Science.gov (United States)

    Ogorodnikova, O. M.; Vaganov, K. A.; Putimtsev, I. D.

    2017-09-01

    This paper presents some important results for cloud-based designing a robot arm by a group of students. Methodology for the cloud-based design was developed and used to initiate interdisciplinary project about research and development of a specific manipulator. The whole project data files were hosted by Ural Federal University data center. The 3D (three-dimensional) model of the robot arm was created using Siemens PLM software (Product Lifecycle Management) and structured as a complex mechatronics product by means of Siemens Teamcenter thin client; all processes were performed in the clouds. The robot arm was designed in purpose to load blanks up to 1 kg into the work space of the milling machine for performing student's researches.

  19. Reflection: Research by Design: Design-Based Research and the Higher Degree Research Student

    Science.gov (United States)

    Kennedy-Clark, Shannon

    2015-01-01

    The article "Research by design: Design-based research and the higher degree research student" (Kennedy-Clark, 2013) appeared in the "Journal of Learning Design" Volume 6, Issue 2 in 2013. Two years on, Shannon Kennedy-Clark reflects upon her original article. Upon being asked to revisit this article the author reflected upon…

  20. Front end design of smartphone-based mobile health

    Science.gov (United States)

    Zhang, Changfan; He, Lingsong; Gao, Zhiqiang; Ling, Cong; Du, Jianhao

    2015-02-01

    Mobile health has been a new trend all over the world with the rapid development of intelligent terminals and mobile internet. It can help patients monitor health in-house and is convenient for doctors to diagnose remotely. Smart-phone-based mobile health has big advantages in cost and data sharing. Front end design of it mainly focuses on two points: one is implementation of medical sensors aimed at measuring kinds of medical signal; another is acquisition of medical signal from sensors to smart phone. In this paper, the above two aspects were both discussed. First, medical sensor implementation was proposed to refer to mature measurement solutions with ECG (electrocardiograph) sensor design taken for example. And integrated chip using can simplify design. Then second, typical data acquisition architecture of smart phones, namely Bluetooth and MIC (microphone)-based architecture, were compared. Bluetooth architecture should be equipped with an acquisition card; MIC design uses sound card of smart phone instead. Smartphone-based virtual instrument app design corresponding to above acquisition architecture was discussed. In experiments, Bluetooth and MIC architecture were used to acquire blood pressure and ECG data respectively. The results showed that Bluetooth design can guarantee high accuracy during the acquisition and transmission process, and MIC design is competitive because of low cost and convenience.

  1. A Time of Flight Fast Neutron Imaging System Design Study

    Science.gov (United States)

    Canion, Bonnie; Glenn, Andrew; Sheets, Steven; Wurtz, Ron; Nakae, Les; Hausladen, Paul; McConchie, Seth; Blackston, Matthew; Fabris, Lorenzo; Newby, Jason

    2017-09-01

    LLNL and ORNL are designing an active/passive fast neutron imaging system that is flexible to non-ideal detector positioning. It is often not possible to move an inspection object in fieldable imager applications such as safeguards, arms control treaty verification, and emergency response. Particularly, we are interested in scenarios which inspectors do not have access to all sides of an inspection object, due to interfering objects or walls. This paper will present the results of a simulation-based design parameter study, that will determine the optimum system design parameters for a fieldable system to perform time-of-flight based imaging analysis. The imaging analysis is based on the use of an associated particle imaging deuterium-tritium (API DT) neutron generator to get the time-of-flight of radiation induced within an inspection object. This design study will investigate the optimum design parameters for such a system (e.g. detector size, ideal placement, etc.), as well as the upper and lower feasible design parameters that the system can expect to provide results within a reasonable amount of time (e.g. minimum/maximum detector efficiency, detector standoff, etc.). Ideally the final prototype from this project will be capable of using full-access techniques, such as transmission imaging, when the measurement circumstances allow, but with the additional capability of producing results at reduced accessibility.

  2. Overview of Fusion-Fission Hybrid Reactor Design Study in China

    International Nuclear Information System (INIS)

    Huang Jinhua; Feng Kaiming; Deng Baiquan; Deng, P.Zh.; Zhang Guoshu; Hu Gang; He Kaihui; Wu Yican; Qiu Lijian; Huang Qunying; Xiao Bingjia; Liu Xiaoping; Chen Yixue; Kong, M.H.

    2002-01-01

    The motivation for developing fusion-fission hybrid reactors is discussed in the context of electricity power requirements by 2050 in China. A detailed conceptual design of the Fusion Experimental Breeder (FEB) was developed from 1986-1995. The FEB has a subignited tokamak fusion core with a major radius of 4.0 m, a fusion power of 145 MW, and a fusion energy gain Q of 3. Based on this, an engineering outline design study of the FEB, FEB-E, has been performed. This design study is a transition from conceptual to engineering design in this research. The main results beyond that given in the detailed conceptual design are included in this paper, namely, the design studies of the blanket, divertor, test blanket, and tritium and environment issues. In-depth analyses have been performed to support the design. Studies of related advanced concepts such as the waste transmutation blanket concept and the spherical tokamak core concept are also presented

  3. Parametric study for design of thermal sleeves

    International Nuclear Information System (INIS)

    Mukherjee, A.B.; Mehra, V.K.

    1985-01-01

    Thermal sleeves are used inside nozzle in many reactor components. Basic aim in design of thermal sleeve is to arrive at a set of dimensions for gap and annulus length, which will give rise to minimum thermal gradient in the base metal of the associated nozzle. Study includes the minimisation of the thermal gradient in the crotch zone by suitable choice of gap and annulus length. Three different geometries of nozzle radii 50.00 mm., 100 mm. and 200.0 mm. are studied for single and two concentric thermal sleeves model. The paper also presents effect of parameters like velocity of flow, temperature of fluid, materials etc. on the design of thermal sleeves. (orig.)

  4. Rationale and design of the GUIDE-IT study: Guiding Evidence Based Therapy Using Biomarker Intensified Treatment in Heart Failure.

    Science.gov (United States)

    Felker, G Michael; Ahmad, Tariq; Anstrom, Kevin J; Adams, Kirkwood F; Cooper, Lawton S; Ezekowitz, Justin A; Fiuzat, Mona; Houston-Miller, Nancy; Januzzi, James L; Leifer, Eric S; Mark, Daniel B; Desvigne-Nickens, Patrice; Paynter, Gayle; Piña, Ileana L; Whellan, David J; O'Connor, Christopher M

    2014-10-01

    The GUIDE-IT (Guiding Evidence Based Therapy Using Biomarker Intensified Treatment in Heart Failure) study is designed to determine the safety, efficacy, and cost-effectiveness of a strategy of adjusting therapy with the goal of achieving and maintaining a target N-terminal pro-B-type natriuretic peptide (NT-proBNP) level of levels provide key prognostic information in patients with HF. Therapies proven to improve outcomes in patients with HF are generally associated with decreasing levels of NPs, and observational data show that decreases in NP levels over time are associated with favorable outcomes. Results from smaller prospective, randomized studies of this strategy thus far have been mixed, and current guidelines do not recommend serial measurement of NP levels to guide therapy in patients with HF. GUIDE-IT is a prospective, randomized, controlled, unblinded, multicenter clinical trial designed to randomize approximately 1,100 high-risk subjects with systolic HF (left ventricular ejection fraction ≤40%) to either usual care (optimized guideline-recommended therapy) or a strategy of adjusting therapy with the goal of achieving and maintaining a target NT-proBNP level of study are followed up at regular intervals and after treatment adjustments for a minimum of 12 months. The primary endpoint of the study is time to cardiovascular death or first hospitalization for HF. Secondary endpoints include time to cardiovascular death and all-cause mortality, cumulative mortality, health-related quality of life, resource use, cost-effectiveness, and safety. The GUIDE-IT study is designed to definitively assess the effects of an NP-guided strategy in high-risk patients with systolic HF on clinically relevant endpoints of mortality, hospitalization, quality of life, and medical resource use. (Guiding Evidence Based Therapy Using Biomarker Intensified Treatment in Heart Failure [GUIDE-IT]; NCT01685840). Copyright © 2014 American College of Cardiology Foundation

  5. Fragment-based drug design.

    Science.gov (United States)

    Feyfant, Eric; Cross, Jason B; Paris, Kevin; Tsao, Désirée H H

    2011-01-01

    Fragment-based drug design (FBDD), which is comprised of both fragment screening and the use of fragment hits to design leads, began more than 15 years ago and has been steadily gaining in popularity and utility. Its origin lies on the fact that the coverage of chemical space and the binding efficiency of hits are directly related to the size of the compounds screened. Nevertheless, FBDD still faces challenges, among them developing fragment screening libraries that ensure optimal coverage of chemical space, physical properties and chemical tractability. Fragment screening also requires sensitive assays, often biophysical in nature, to detect weak binders. In this chapter we will introduce the technologies used to address these challenges and outline the experimental advantages that make FBDD one of the most popular new hit-to-lead process.

  6. Conceptual design of distillation-based hybrid separation processes.

    Science.gov (United States)

    Skiborowski, Mirko; Harwardt, Andreas; Marquardt, Wolfgang

    2013-01-01

    Hybrid separation processes combine different separation principles and constitute a promising design option for the separation of complex mixtures. Particularly, the integration of distillation with other unit operations can significantly improve the separation of close-boiling or azeotropic mixtures. Although the design of single-unit operations is well understood and supported by computational methods, the optimal design of flowsheets of hybrid separation processes is still a challenging task. The large number of operational and design degrees of freedom requires a systematic and optimization-based design approach. To this end, a structured approach, the so-called process synthesis framework, is proposed. This article reviews available computational methods for the conceptual design of distillation-based hybrid processes for the separation of liquid mixtures. Open problems are identified that must be addressed to finally establish a structured process synthesis framework for such processes.

  7. Designing a New Car Rental Service Using Location-Based Services

    OpenAIRE

    Dessie, Solomon

    2015-01-01

    This thesis concentrates on improving the car rental services offered by the case company by introducing location-based services. For many years, the company has conducted a rental business in a similar manner with other car rental companies, and now it is introducing a new service system based on online interaction and location-based services. The outcome of the study is a blueprint for the case company regarding the design of a car rental service using location-based services. This stud...

  8. Designing a Virtual-Reality-Based, Gamelike Math Learning Environment

    Science.gov (United States)

    Xu, Xinhao; Ke, Fengfeng

    2016-01-01

    This exploratory study examined the design issues related to a virtual-reality-based, gamelike learning environment (VRGLE) developed via OpenSimulator, an open-source virtual reality server. The researchers collected qualitative data to examine the VRGLE's usability, playability, and content integration for math learning. They found it important…

  9. Designing Digital Problem Based Learning Tasks that Motivate Students

    Science.gov (United States)

    van Loon, Anne-Marieke; Ros, Anje; Martens, Rob

    2013-01-01

    This study examines whether teachers are able to apply the principles of autonomy support and structure support in designing digital problem based learning (PBL) tasks. We examine whether these tasks are more autonomy- and structure-supportive and whether primary and secondary school students experience greater autonomy, competence, and motivation…

  10. A new design approach to innovative spectrometers. Case study: TROPOLITE

    Science.gov (United States)

    Volatier, Jean-Baptiste; Baümer, Stefan; Kruizinga, Bob; Vink, Rob

    2014-05-01

    Designing a novel optical system is a nested iterative process. The optimization loop, from a starting point to final system is already mostly automated. However this loop is part of a wider loop which is not. This wider loop starts with an optical specification and ends with a manufacturability assessment. When designing a new spectrometer with emphasis on weight and cost, numerous iterations between the optical- and mechanical designer are inevitable. The optical designer must then be able to reliably produce optical designs based on new input gained from multidisciplinary studies. This paper presents a procedure that can automatically generate new starting points based on any kind of input or new constraint that might arise. These starting points can then be handed over to a generic optimization routine to make the design tasks extremely efficient. The optical designer job is then not to design optical systems, but to meta-design a procedure that produces optical systems paving the way for system level optimization. We present here this procedure and its application to the design of TROPOLITE a lightweight push broom imaging spectrometer.

  11. Multiscale Study of Hydrogen Adsorption on Six Designed Covalent Organic Frameworks Based on Porphyrazine, Cyclobutane and Scandium

    International Nuclear Information System (INIS)

    Li Le-Le; Gao Teng-Fei; Zhang Ruan-Yu; Zhang Hong

    2014-01-01

    The first-principles method of hydrogen adsorption is used to investigate the interaction of H_2 with the scandium-porphyrazine (Sc-Pz) and porphyrazine (Pz) clusters. The result shows that the interaction of H_2 with Sc-Pz is stronger than with Pz. Then grand canonical Monte Carlo simulations are used to investigate hydrogen adsorption in six designed covalent organic frameworks (COFs), which are designed based on porphyrazine, cyclobutane and scandium. When the pressure is from 0.1 to 100 bar and the temperature is 298 K and 77 K, the hydrogen adsorption capacities of the six COFs are calculated. We further study the importance of Sc and fillers to improve the H_2 uptake in the modified COFs by analyzing the isosteric heat of hydrogen adsorption. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  12. On the design of henon and logistic map-based random number generator

    Science.gov (United States)

    Magfirawaty; Suryadi, M. T.; Ramli, Kalamullah

    2017-10-01

    The key sequence is one of the main elements in the cryptosystem. True Random Number Generators (TRNG) method is one of the approaches to generating the key sequence. The randomness source of the TRNG divided into three main groups, i.e. electrical noise based, jitter based and chaos based. The chaos based utilizes a non-linear dynamic system (continuous time or discrete time) as an entropy source. In this study, a new design of TRNG based on discrete time chaotic system is proposed, which is then simulated in LabVIEW. The principle of the design consists of combining 2D and 1D chaotic systems. A mathematical model is implemented for numerical simulations. We used comparator process as a harvester method to obtain the series of random bits. Without any post processing, the proposed design generated random bit sequence with high entropy value and passed all NIST 800.22 statistical tests.

  13. Advanced Information Technology in Simulation Based Life Cycle Design

    Science.gov (United States)

    Renaud, John E.

    2003-01-01

    In this research a Collaborative Optimization (CO) approach for multidisciplinary systems design is used to develop a decision based design framework for non-deterministic optimization. To date CO strategies have been developed for use in application to deterministic systems design problems. In this research the decision based design (DBD) framework proposed by Hazelrigg is modified for use in a collaborative optimization framework. The Hazelrigg framework as originally proposed provides a single level optimization strategy that combines engineering decisions with business decisions in a single level optimization. By transforming this framework for use in collaborative optimization one can decompose the business and engineering decision making processes. In the new multilevel framework of Decision Based Collaborative Optimization (DBCO) the business decisions are made at the system level. These business decisions result in a set of engineering performance targets that disciplinary engineering design teams seek to satisfy as part of subspace optimizations. The Decision Based Collaborative Optimization framework more accurately models the existing relationship between business and engineering in multidisciplinary systems design.

  14. Performance-based seismic design of steel frames utilizing colliding bodies algorithm.

    Science.gov (United States)

    Veladi, H

    2014-01-01

    A pushover analysis method based on semirigid connection concept is developed and the colliding bodies optimization algorithm is employed to find optimum seismic design of frame structures. Two numerical examples from the literature are studied. The results of the new algorithm are compared to the conventional design methods to show the power or weakness of the algorithm.

  15. Designing and Evaluating Conative Game-Based Learning Scenarios

    DEFF Research Database (Denmark)

    Schønau-Fog, Henrik

    2014-01-01

    It is an essential prerequisite to design for motivation in game-based learning applications, tools and activities. However, how is it possible to design and evaluate motivational game-based learning scenarios in a systematic process-oriented manner based on conation and player engagement? While...... of ‘continuation desire’ such as interfacing with the scenario, exploration and socialising. This paper aims to combine the concepts of Player Engagement, Conation and Continuation Desire by focusing on the conative aspects which are the essential drivers for the desire to continue any learning activity......-based learning scenarios....

  16. Structural design systems using knowledge-based techniques

    International Nuclear Information System (INIS)

    Orsborn, K.

    1993-01-01

    Engineering information management and the corresponding information systems are of a strategic importance for industrial enterprises. This thesis treats the interdisciplinary field of designing computing systems for structural design and analysis using knowledge-based techniques. Specific conceptual models have been designed for representing the structure and the process of objects and activities in a structural design and analysis domain. In this thesis, it is shown how domain knowledge can be structured along several classification principles in order to reduce complexity and increase flexibility. By increasing the conceptual level of the problem description and representation of the domain knowledge in a declarative form, it is possible to enhance the development, maintenance and use of software for mechanical engineering. This will result in a corresponding increase of the efficiency of the mechanical engineering design process. These ideas together with the rule-based control point out the leverage of declarative knowledge representation within this domain. Used appropriately, a declarative knowledge representation preserves information better, is more problem-oriented and change-tolerant than procedural representations. 74 refs

  17. Design study of underground facility of the Underground Research Laboratory

    International Nuclear Information System (INIS)

    Hibiya, Keisuke; Akiyoshi, Kenji; Ishizuka, Mineo; Anezaki, Susumu

    1998-03-01

    Geoscientific research program to study deep geological environment has been performed by Power Reactor and Nuclear Fuel Development Corporation (PNC). This research is supported by 'Long-Term Program for Research, Development and Utilization of Nuclear Energy'. An Underground Research Laboratory is planned to be constructed at Shoma-sama Hora in the research area belonging to PNC. A wide range of geoscientific research and development activities which have been previously studied at the Tono Area is planned in the laboratory. The Underground Research Laboratory is consisted of Surface Laboratory and Underground Research Facility located from the surface down to depth between several hundreds and 1,000 meters. Based on the results of design study in last year, the design study performed in this year is to investigate the followings in advance of studies for basic design and practical design: concept, design procedure, design flow and total layout. As a study for the concept of the underground facility, items required for the facility are investigated and factors to design the primary form of the underground facility are extracted. Continuously, design methods for the vault and the underground facility are summarized. Furthermore, design procedures of the extracted factors are summarized and total layout is studied considering the results to be obtained from the laboratory. (author)

  18. DENA: A Configurable Microarchitecture and Design Flow for Biomedical DNA-Based Logic Design.

    Science.gov (United States)

    Beiki, Zohre; Jahanian, Ali

    2017-10-01

    DNA is known as the building block for storing the life codes and transferring the genetic features through the generations. However, it is found that DNA strands can be used for a new type of computation that opens fascinating horizons in computational medicine. Significant contributions are addressed on design of DNA-based logic gates for medical and computational applications but there are serious challenges for designing the medium and large-scale DNA circuits. In this paper, a new microarchitecture and corresponding design flow is proposed to facilitate the design of multistage large-scale DNA logic systems. Feasibility and efficiency of the proposed microarchitecture are evaluated by implementing a full adder and, then, its cascadability is determined by implementing a multistage 8-bit adder. Simulation results show the highlight features of the proposed design style and microarchitecture in terms of the scalability, implementation cost, and signal integrity of the DNA-based logic system compared to the traditional approaches.

  19. Designing a Situational Awareness Information Display: Adopting an Affordance-Based Framework to Amplify User Experience in Environmental Interaction Design

    Directory of Open Access Journals (Sweden)

    Yingjie Victor Chen

    2016-06-01

    Full Text Available User experience remains a crucial consideration when assessing the successfulness of information visualization systems. The theory of affordances provides a robust framework for user experience design. In this article, we demonstrate a design case that employs an affordance-based framework and evaluate the information visualization display design. SolarWheels is an interactive information visualization designed for large display walls in computer network control rooms to help cybersecurity analysts become aware of network status and emerging issues. Given the critical nature of this context, the status and performance of a computer network must be precisely monitored and remedied in real time. In this study, we consider various aspects of affordances in order to amplify the user experience via visualization and interaction design. SolarWheels visualizes the multilayer multidimensional computer network issues with a series of integrated circular visualizations inspired by the metaphor of the solar system. To amplify user interaction and experience, the system provides a three-zone physical interaction that allows multiple users to interact with the system. Users can read details at different levels depending on their distance from the display. An expert evaluation study, based on a four-layer affordance framework, was conducted to assess and improve the interactive visualization design.

  20. Design for mood : Twenty activity-based opportunities to design for mood regulation

    NARCIS (Netherlands)

    Desmet, P.M.A.

    2015-01-01

    This paper introduces a theory-based approach to design for mood regulation. The main proposition is that design can best influence mood by enabling and stimulating people to engage in a broad range of mood-regulating activities. The first part of the manuscript reviews state-of-the art mood-focused

  1. Study on Design Optimization of Centrifugal Compressors Considering Efficiency and Weight

    International Nuclear Information System (INIS)

    Lee, Younghwan; Kang, Shinhyoung; Ha, Kyunggu

    2015-01-01

    Various centrifugal compressors are currently used extensively in industrial fields, where the design requirements are more complicated. This makes it more difficult to determine the optimal design point of a centrifugal compressor. Traditionally, the efficiency is an important factor for optimization. In this study, the weight of the compressor was also considered. The aim of this study was to present the design tendency considering the stage efficiency and weight. In addition, this study suggested possibility of a selection of compressor design objectives at an early design stage based on the optimization results. Only a vaneless diffuser was considered in this case. The Kriging method was used with sample points from 1D design program data. The optimal points were determined in a substitute design space.

  2. Study on Design Optimization of Centrifugal Compressors Considering Efficiency and Weight

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Younghwan; Kang, Shinhyoung [Seoul National University, Seoul (Korea, Republic of); Ha, Kyunggu [Hyundai Motor Group, Ulsan (Korea, Republic of)

    2015-04-15

    Various centrifugal compressors are currently used extensively in industrial fields, where the design requirements are more complicated. This makes it more difficult to determine the optimal design point of a centrifugal compressor. Traditionally, the efficiency is an important factor for optimization. In this study, the weight of the compressor was also considered. The aim of this study was to present the design tendency considering the stage efficiency and weight. In addition, this study suggested possibility of a selection of compressor design objectives at an early design stage based on the optimization results. Only a vaneless diffuser was considered in this case. The Kriging method was used with sample points from 1D design program data. The optimal points were determined in a substitute design space.

  3. Design method of general-purpose driving circuit for CCD based on CPLD

    International Nuclear Information System (INIS)

    Zhang Yong; Tang Benqi; Xiao Zhigang; Wang Zujun; Huang Shaoyan

    2005-01-01

    It is very important for studying the radiation damage effects and mechanism systematically about CCD to develop a general-purpose test platform. The paper discusses the design method of general-purpose driving circuit for CCD based on CPLD and the realization approach. A main controller has being designed to read the data file from the outer memory, setup the correlative parameter registers and produce the driving pulses according with parameter request strictly, which is based on MAX7000S by using MAX-PLUS II software. The basic driving circuit module has being finished based on this method. The output waveform of the module is the same figure as the simulation waveform. The result indicates that the design method is feasible. (authors)

  4. Study on design method for seismically isolated FBR plants

    International Nuclear Information System (INIS)

    Hirata, Kazuta; Yabana, Shuichi; Ohtori, Yasuki; Ishida, Katsuhiko; Sawada, Yoshihiro; Shiojiri; Hiroo; Mazda, Taiji

    1998-01-01

    CRIEPI conducted 'Demonstration test on FBR seismic isolation system' from 1987 to 1996 under contract with Ministry of International Trade and Industry, Japan. In the demonstration test, base isolation technologies are prepared and demonstrated to apply to FBR and the design guidelines are proposed. In this report overall contents of the design guidelines entitled Design guidelines for seismically base isolated FBR plants' are included. The design guidelines, as a rule, are limited to apply to FBR plants where entire reactor building is isolated in the horizontal direction using laminated rubber bearings as isolators. The design guidelines and its concepts, however, will be useful for the development of similar guidelines for other isolation systems using different type of isolation methods and other nuclear facilities. The design guidelines consist of three parts and appendices. The first part is 'Policy for Safety Design of Base Isolated FBR Plants' specifying the principles and the requirements in the planning and the design for the safety of base isolated FBR plants. The second part is Policy for Seismic Design of Base Isolated FBR' describing the principles and the requirements in the seismic design and the evaluation of safety for base isolated FBR plants. The third part is 'Design Methods for Seismic Isolated FBR Plants' detailing the methods, procedures and parameters to be used in the design and the evaluation of safety fro base isolated FBR plants. In appendices examples of design procedures for base isolated reactor building and laminated rubber bearings as well as various test data on laminated rubber bearings, etc. are shown. (author)

  5. Design and Co-design of Project-organized Studies

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Lerche; Andreasen, Lars Birch

    2014-01-01

    The chapter contributes to discussions on design processes in relation to education, presenting different notions of design research and demonstrating how professors and students are involved together in designing innovative and constructive study processes that can help foster students' engagement...

  6. Overview of energy-conserving development planning and design techniques based on five case studies

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Findings and recommendations are presented of a review of five case studies of ways to conserve energy through development planning and site design in communities. Two approaches were used. In the first approach, a conventional, pre-existing plan was analyzed to determine potential energy use. Once energy-conservation options were identified and evaluated, the conventional plan was modified by employing those options. This approach was used in The Woodlands, Burke Center, and Radisson studies. In the second approach, energy-conservation options are independently identified and evaluated. Those options that passed specific criteria screening were then utilized in developing one or more totally new plans based on energy objectives. This approach was used in Greenbrier and Shenandoah. Radisson is a new town on the outskirts of Syracuse, New York. Greenbrier is a 3000 acre planned community adjacent to Norfolk and Virginia Beach. Shenandoah is a proposed new town in the Atlanta urbanized area. The Woodlands is a new community under development north of Houston. Burke Center is a residential planned unit development in Fairfax County, Virgnia. (MCW)

  7. Comparative effectiveness of instructional design features in simulation-based education: systematic review and meta-analysis.

    Science.gov (United States)

    Cook, David A; Hamstra, Stanley J; Brydges, Ryan; Zendejas, Benjamin; Szostek, Jason H; Wang, Amy T; Erwin, Patricia J; Hatala, Rose

    2013-01-01

    Although technology-enhanced simulation is increasingly used in health professions education, features of effective simulation-based instructional design remain uncertain. Evaluate the effectiveness of instructional design features through a systematic review of studies comparing different simulation-based interventions. We systematically searched MEDLINE, EMBASE, CINAHL, ERIC, PsycINFO, Scopus, key journals, and previous review bibliographies through May 2011. We included original research studies that compared one simulation intervention with another and involved health professions learners. Working in duplicate, we evaluated study quality and abstracted information on learners, outcomes, and instructional design features. We pooled results using random effects meta-analysis. From a pool of 10,903 articles we identified 289 eligible studies enrolling 18,971 trainees, including 208 randomized trials. Inconsistency was usually large (I2 > 50%). For skills outcomes, pooled effect sizes (positive numbers favoring the instructional design feature) were 0.68 for range of difficulty (20 studies; p simulation-based education.

  8. Design based entrepreneurship

    DEFF Research Database (Denmark)

    Nielsen, Louise Møller; Wikström, Anders; Tollestrup, Christian

    2013-01-01

    Designers are often recognized as natural entrepreneurs, due to their creative skills and competences in the idea-generation and product development processes. A number of studies shows that creative professionals are more likely to become self-employed. In general though, there are not many stud...

  9. Design-based online teacher professional development to introduce integration of STEM in Pakistan

    Science.gov (United States)

    Anwar, Tasneem

    In today's global society where innovations spread rapidly, the escalating focus on science, technology, engineering and mathematics (STEM) has quickly intensified in the United States, East Asia and much of Western Europe. Our ever-changing, increasingly global society faces many multidisciplinary problems, and many of the solutions require the integration of multiple science, technology, engineering, and mathematics (STEM) concepts. Thus, there is a critical need to explore the integration of STEM subjects in international education contexts. This dissertation study examined the exploration of integration of STEM in the unique context of Pakistan. This study used three-phase design-based methodological framework derived from McKenney and Reeves (2012) to explore the development of a STEM focused online teacher professional development (oTPD-STEM) and to identify the design features that facilitate teacher learning. The oTPD-STEM program was designed to facilitate eight Pakistani elementary school teachers' exploration of the new idea of STEM integration through both practical and theoretical considerations. This design-based study employed inductive analysis (Strauss and Corbin, 1998) to analyze multiple data sources of interviews, STEM perception responses, reflective learning team conversations, pre-post surveys and artifacts produced in oTPD-STEM. Findings of this study are presented as: (1) design-based decisions for oTPD-STEM, and (2) evolution in understanding of STEM by sharing participant teachers' STEM model for Pakistani context. This study advocates for the potential of school-wide oTPD for interdisciplinary collaboration through support for learner-centered practices.

  10. Designers' Cognitive Thinking Based on Evolutionary Algorithms

    OpenAIRE

    Zhang Shutao; Jianning Su; Chibing Hu; Peng Wang

    2013-01-01

    The research on cognitive thinking is important to construct the efficient intelligent design systems. But it is difficult to describe the model of cognitive thinking with reasonable mathematical theory. Based on the analysis of design strategy and innovative thinking, we investigated the design cognitive thinking model that included the external guide thinking of "width priority - depth priority" and the internal dominated thinking of "divergent thinking - convergent thinking", built a reaso...

  11. Facilitating Consensus in Cooperative Design Processes using animation-based sketching

    DEFF Research Database (Denmark)

    Vistisen, Peter; Rosenstand, Claus Andreas Foss

    2016-01-01

    In the following paper we show how animation can be used as a digital sketching tool to facilitate cooperative work processes when exploring the application of non-idiomatic digital technologies. Focus is on the early stages of the design process, framed as ‘product formation’. Based on the results...... from a action research case study at the North Sea Oceanarium we show that animation can act as a tool to create clear representations of the quality criteria at hand, and thus enable a richer feedback loop between the different stakeholders in the design process. The main contribution...... in cooperative design processes, and detail how the techniques differs from other representational options in the early design process....

  12. How Design-based Research, Action Research and Interaction Design Contributes to the Development of Designs for Learning

    DEFF Research Database (Denmark)

    Majgaard, Gunver; Misfeldt, Morten; Nielsen, Jacob

    2011-01-01

    This article explores how action research, design based research and interaction design can be combined and used in the development of educational robotic tools. Our case study is the development of Number Blocks and it combines physical interaction, learning, and immediate feedback. Number Blocks...... supports the children's understanding of place value in the sense that it allows them to experiment with creating large numbers. The development was done in collaboration with a class of 7-8 year old children and their mathematics teacher. The article argues that elements from different research methods...... allowed a structured approach to projects that combines educational research and innovation of new learning technologies. Key elements of this approach is acknowledging the users input, developing a theoretical pre-analysis and using an iterative approach....

  13. Reliability-Based Optimal Design for Very Large Floating Structure

    Institute of Scientific and Technical Information of China (English)

    ZHANG Shu-hua(张淑华); FUJIKUBO Masahiko

    2003-01-01

    Costs and losses induced by possible future extreme environmental conditions and difficulties in repairing post-yielding damage strongly suggest the need for proper consideration in design rather than just life loss prevention. This can be addressed through the development of design methodology that balances the initial cost of the very large floating structure (VLFS) against the expected potential losses resulting from future extreme wave-induced structural damage. Here, the development of a methodology for determining optimal, cost-effective design will be presented and applied to a VLFS located in the Tokyo bay. Optimal design criteria are determined based on the total expected life-cycle cost and acceptable damage probability and curvature of the structure, and a set of sizes of the structure are obtained. The methodology and applications require expressions of the initial cost and the expected life-cycle damage cost as functions of the optimal design variables. This study includes the methodology, total life-cycle cost function, structural damage modeling, and reliability analysis.

  14. Designing Shopping Area Atmospheric Using Choice-based Conjoint Analysis: Case Study at Soekarno-Hatta International Airport

    Directory of Open Access Journals (Sweden)

    Suzianti Amalia

    2017-01-01

    Full Text Available As a response to overcapacity issue at Soekarno-Hatta International Airport, the government is recently planning on building larger terminal buildings to transport passengers. However, in designing an excellent terminal building, one should not only consider how to process passengers in the most efficient way, but also how facility-based environmental cues, or atmospheric cues, affect consumers’ emotional state and shopping behavior. This research aims at examining passenger preferences towards atmospheric cues in airport shopping area and proposing a shopping area design based on consumer preferences. Choice-based conjoint was conducted towards 500 passengers at Soekarno-Hatta International Airport. Research findings suggested that there is a significant correlation between atmospheric cues and consumers’ purchase intention in airport shopping area. Passengers prefer a shopping area with high in-store visibility, cool colors for window display, floors, wall, and ceiling, and bright lighting for airport hallway. This research also concludes that Socio-economic Status (SES affects passengers’ preferences.

  15. Case-based reasoning support for engineering design

    Science.gov (United States)

    Lees, Brian; Hamza, Meer; Irgens, Chris

    2000-10-01

    The potential application of case-based reasoning (CBR) in design support is illustrated through examples drawn from research at the University of Paisley, demonstrating the suitability of CBR for different aspects of design, different problem areas, and different design goals. A quality advisory system has been developed for the early stages of mechanical engineering design, the aim of which is to provide quality advice in a variant design situation. In the domain of software engineering CBR has been applied to advise on which metrics are appropriate fora assessing the quality of the software currently under design. The system integrates CBR with concepts from quality function deployment (QFD) and incorporates a case library holding past software quality histories. CBR has been applied in support of conceptual design: to capture detailed design histories by monitoring designer actions, and thereby support design reuse through the evaluation of designs, through the provision of query, browsing and replay facilities. The resulting system is aimed to support the design of safety critical systems, by assisting in the construction of safety arguments, and cooperative design.

  16. The Study on Heuristic and Algorithmic Processing Creative Training on Product Design Education: Based on the Bags & Luggage design Course

    Directory of Open Access Journals (Sweden)

    Zhang Ziran

    2018-01-01

    Full Text Available In the study, context-creativity of Teresa M. Amabile was used as The foundation to apply it in the bags & luggage design course. Moreover, the sectional creative training education mode of prior heuristic task and postpositional algorithmic task was proposed. 26 junior students in product design were used as the trial objects. The Consensual Technique for Creativity (CAT was considered as the scoring standard of creative performance. In the end, the sectional theoretical framework of effective creative training in product design was finally proposed.

  17. Evidence-Based Conclusions Concerning Practice, Curriculum Design and Curriculum Reform in a Civil Engineering Capstone Design Course in Hong Kong

    Science.gov (United States)

    Chan, Cecilia K. Y.; Wong, George C. K.; Law, Ada K. H.; Zhang, T.; Au, Francis T. K.

    2017-01-01

    This study aimed to provide evidence-based conclusions from students concerning a capstone-design course in a civil engineering programme in Hong Kong. The evidence was generated by designing a student-experience questionnaire. The questionnaire instrument was assessed for internal consistency in four scales (curriculum and structure changes;…

  18. Designing an Agent-Based Model for Childhood Obesity Interventions: A Case Study of ChildObesity180.

    Science.gov (United States)

    Hennessy, Erin; Ornstein, Joseph T; Economos, Christina D; Herzog, Julia Bloom; Lynskey, Vanessa; Coffield, Edward; Hammond, Ross A

    2016-01-07

    Complex systems modeling can provide useful insights when designing and anticipating the impact of public health interventions. We developed an agent-based, or individual-based, computation model (ABM) to aid in evaluating and refining implementation of behavior change interventions designed to increase physical activity and healthy eating and reduce unnecessary weight gain among school-aged children. The potential benefits of applying an ABM approach include estimating outcomes despite data gaps, anticipating impact among different populations or scenarios, and exploring how to expand or modify an intervention. The practical challenges inherent in implementing such an approach include data resources, data availability, and the skills and knowledge of ABM among the public health obesity intervention community. The aim of this article was to provide a step-by-step guide on how to develop an ABM to evaluate multifaceted interventions on childhood obesity prevention in multiple settings. We used data from 2 obesity prevention initiatives and public-use resources. The details and goals of the interventions, overview of the model design process, and generalizability of this approach for future interventions is discussed.

  19. Guide for the realization of Design Base Documents (DBD)

    International Nuclear Information System (INIS)

    Roca Mallofre, G. la

    2010-01-01

    Guide for improving the consistency and quality content of the Design Base Documents. It's a short description of how to carry out and complete these Documents but focusing on those aspects that can be more confusing and harder to interpret. This guide aims to clarify the term Design Base distinguishing between production and safety, and it focuses on safety Design Base Documents and their values and references. It also emphasizes the difference between the support system and the interface system when there is a functional connection between different systems.

  20. Quiet engine program flight engine design study

    Science.gov (United States)

    Klapproth, J. F.; Neitzel, R. E.; Seeley, C. T.

    1974-01-01

    The results are presented of a preliminary flight engine design study based on the Quiet Engine Program high-bypass, low-noise turbofan engines. Engine configurations, weight, noise characteristics, and performance over a range of flight conditions typical of a subsonic transport aircraft were considered. High and low tip speed engines in various acoustically treated nacelle configurations were included.

  1. Research by Design: Design-Based Research and the Higher Degree Research student

    Science.gov (United States)

    Kennedy-Clark, Shannon

    2013-01-01

    Design-based research lends itself to educational research as the aim of this approach is to develop and refine the design of artefacts, tools and curriculum and to advance existing theory or develop new theories that can support and lead to a deepened understanding of learning. This paper provides an overview of the potential benefits of using a…

  2. Interior Design Based on Forough Farrokhzad Poetry

    Directory of Open Access Journals (Sweden)

    Mahsa Sanami

    2018-03-01

    Full Text Available The main purpose of this study is to correlate between art, literature, architect and visualization to translate the emotions and aspirations embodied in a well-known poet such as Forough Farrokhzad. Forough Farrokhzad widely regarded as a famous Iranian poet and an advocate for women’s liberation and independence. She wrote during a time when Iranian women were facing extensive discrimination and prejudice. Many of her works are rich in feminist related aspects of Iranian women. By visualization of Forough’s inner feelings, one can see a great revaluation in society towards women feelings and emotions. Like any other human, poets and artist both have thoughts and dreams rich in colors and words capsulizing their imaginary world in possible dreams which are all related to each person’s personality, culture, environment and etc. One of the ways to understand a poet is to understand the depth of his/her thoughts through his/her poems. Thus the main purpose of this research is to review interior design based on in depth analysis of related poems. Psychoanalysis of symbols, themes and colors used in poems, can be used to supplement words in extracting symptoms and energy depicting the poet inner feelings and imaginations when designing. The results of the discussing symbols and colors used by Forough in most of her poems, indicate her interest in life, death, love, society, intellectuality and philosophy. Finally the researchers through usage of visual effects and pictures used in her designs tries to assist the viewers to understand and feel the poet’s emotions and passions for life at the time of creating the poems. Thus, it can be assumed that the interior design is based on poetry rich in motion and dynamism.

  3. Toward time-based design: Creating an applied time evaluation checklist for urban design research

    Directory of Open Access Journals (Sweden)

    Amir Shakibamanesh

    2017-09-01

    Full Text Available The perception of a 3D space, in which movement takes place, is subjectively based on experience. The pedestrians’ perception of subjective duration is one of the related issues that receive little attention in urban design literature. Pedestrians often misperceive the required time to pass a certain distance. A wide range of factors affects one׳s perception of time in urban environments. These factors include individual factors (e.g., gender, age, and psychological state, social and cultural contexts, purpose and motivation for being in the space, and knowledge of the given area. This study aims to create an applied checklist that can be used by urban designers in analyzing the effects of individual experience on subjective duration. This checklist will enable urban designers to perform a phenomenological assessment of time perception and compare this perception in different urban spaces, thereby improving pedestrians’ experiences of time through a purposeful design. A combination of exploratory and descriptive analytical research is used as methodology due to the complexity of time perception.

  4. Computer vision based room interior design

    Science.gov (United States)

    Ahmad, Nasir; Hussain, Saddam; Ahmad, Kashif; Conci, Nicola

    2015-12-01

    This paper introduces a new application of computer vision. To the best of the author's knowledge, it is the first attempt to incorporate computer vision techniques into room interior designing. The computer vision based interior designing is achieved in two steps: object identification and color assignment. The image segmentation approach is used for the identification of the objects in the room and different color schemes are used for color assignment to these objects. The proposed approach is applied to simple as well as complex images from online sources. The proposed approach not only accelerated the process of interior designing but also made it very efficient by giving multiple alternatives.

  5. Design of an MSAT-X mobile transceiver and related base and gateway stations

    Science.gov (United States)

    Fang, Russell J. F.; Bhaskar, Udaya; Hemmati, Farhad; Mackenthun, Kenneth M.; Shenoy, Ajit

    This paper summarizes the results of a design study of the mobile transceiver, base station, and gateway station for NASA's proposed Mobile Satellite Experiment (MSAT-X). Major ground segment system design issues such as frequency stability control, modulation method, linear predictive coding vocoder algorithm, and error control technique are addressed. The modular and flexible transceiver design is described in detail, including the core, RF/IF, modem, vocoder, forward error correction codec, amplitude-companded single sideband, and input/output modules, as well as the flexible interface. Designs for a three-carrier base station and a 10-carrier gateway station are also discussed, including the interface with the controllers and with the public-switched telephone networks at the gateway station. Functional specifications are given for the transceiver, the base station, and the gateway station.

  6. Design of an MSAT-X mobile transceiver and related base and gateway stations

    Science.gov (United States)

    Fang, Russell J. F.; Bhaskar, Udaya; Hemmati, Farhad; Mackenthun, Kenneth M.; Shenoy, Ajit

    1987-01-01

    This paper summarizes the results of a design study of the mobile transceiver, base station, and gateway station for NASA's proposed Mobile Satellite Experiment (MSAT-X). Major ground segment system design issues such as frequency stability control, modulation method, linear predictive coding vocoder algorithm, and error control technique are addressed. The modular and flexible transceiver design is described in detail, including the core, RF/IF, modem, vocoder, forward error correction codec, amplitude-companded single sideband, and input/output modules, as well as the flexible interface. Designs for a three-carrier base station and a 10-carrier gateway station are also discussed, including the interface with the controllers and with the public-switched telephone networks at the gateway station. Functional specifications are given for the transceiver, the base station, and the gateway station.

  7. Design study of a negative-ion based NBI system for JT-60U

    International Nuclear Information System (INIS)

    Akino, Noboru; Araki, Masanori; Ebisawa, Noboru

    1994-03-01

    A high energy negative-ion based NBI system for JT-60U has been designed. The objective of the NBI system is to demonstrate mega-ampere level NB current drive and plasma core heating in a reactor-grade high density plasma. This is the first negative-ion based NBI system in the world. The required specifications of the NBI system are; a beam energy of 500 keV, an injection power of 10 MW, a beam pulse duration of 10 sec with a duty cycle of 1/60 and a beam species of deuterium or hydrogen. The neutral beam power of 10 MW is injected tangentially using one beam-line with two large negative-ion sources. The construction of the NBI system has been started, and will be operational in 1996. (author)

  8. Improving the analysis of designed studies by combining statistical modelling with study design information

    NARCIS (Netherlands)

    Thissen, U.; Wopereis, S.; Berg, S.A.A. van den; Bobeldijk, I.; Kleemann, R.; Kooistra, T.; Dijk, K.W. van; Ommen, B. van; Smilde, A.K.

    2009-01-01

    Background: In the fields of life sciences, so-called designed studies are used for studying complex biological systems. The data derived from these studies comply with a study design aimed at generating relevant information while diminishing unwanted variation (noise). Knowledge about the study

  9. A Learning and Interaction design framework, from a study on formulating principles for the design of engaging music learning games

    DEFF Research Database (Denmark)

    Weitze, Charlotte Lærke; Ørngreen, Rikke

    2012-01-01

    Based on a preliminary action research study investigating the design of digital music games and years of experiences from interaction design processes of learning resources, this extended abstract presents a framework that mixes designs for learning principles and game design with a process view...... using a simple interaction design lifecycle. Though the first outset was to design engaging music games, the resulting framework has a more generic character....

  10. Design Transformations for Rule-based Procedural Modeling

    KAUST Repository

    Lienhard, Stefan; Lau, Cheryl; Mü ller, Pascal; Wonka, Peter; Pauly, Mark

    2017-01-01

    We introduce design transformations for rule-based procedural models, e.g., for buildings and plants. Given two or more procedural designs, each specified by a grammar, a design transformation combines elements of the existing designs to generate new designs. We introduce two technical components to enable design transformations. First, we extend the concept of discrete rule switching to rule merging, leading to a very large shape space for combining procedural models. Second, we propose an algorithm to jointly derive two or more grammars, called grammar co-derivation. We demonstrate two applications of our work: we show that our framework leads to a larger variety of models than previous work, and we show fine-grained transformation sequences between two procedural models.

  11. Design Transformations for Rule-based Procedural Modeling

    KAUST Repository

    Lienhard, Stefan

    2017-05-24

    We introduce design transformations for rule-based procedural models, e.g., for buildings and plants. Given two or more procedural designs, each specified by a grammar, a design transformation combines elements of the existing designs to generate new designs. We introduce two technical components to enable design transformations. First, we extend the concept of discrete rule switching to rule merging, leading to a very large shape space for combining procedural models. Second, we propose an algorithm to jointly derive two or more grammars, called grammar co-derivation. We demonstrate two applications of our work: we show that our framework leads to a larger variety of models than previous work, and we show fine-grained transformation sequences between two procedural models.

  12. Demand-Based Optimal Design of Storage Tank with Inerter System

    Directory of Open Access Journals (Sweden)

    Shiming Zhang

    2017-01-01

    Full Text Available A parameter optimal design method for a tank with an inerter system is proposed in this study based on the requirements of tank vibration control to improve the effectiveness and efficiency of vibration control. Moreover, a response indicator and a cost control indicator are selected based on the control targets for liquid storage tanks for simultaneously minimizing the dynamic response and controlling costs. These indicators are reformulated through a random vibration analysis under virtual excitation. The problem is then transformed from a multiobjective optimization problem to a single-objective nonlinear problem using the ε-constraint method, which is consistent with the demand-based method. White noise excitation can be used to design the tank with the inerter system under seismic excitation to simplify the calculation. Subsequently, a MATLAB-based calculation program is compiled, and several optimization cases are examined under different excitation conditions. The effectiveness of the demand-based method is proven through a time history analysis. The results show that specific vibration control requirements can be met at the lowest cost with a simultaneous reduction in base shears and overturning base moments.

  13. A Dish-based Semi-quantitative food frequency questionnaire for assessment of dietary intakes in epidemiologic studies in Iran: Design and development

    OpenAIRE

    Ammar Hassanzadeh Keshteli; Ahmad Esmaillzadeh; Somayeh Rajaie; Gholamreza Askari; Christine Feinle-Bisset; Peyman Adibi

    2014-01-01

    Background: Earlier forms of food frequency questionnaire (FFQ) used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ). Methods: Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a nove...

  14. Property Based Process and Product Synthesis and Design

    DEFF Research Database (Denmark)

    Eden, Mario Richard

    2003-01-01

    in terms of the constitutive (synthesis/design) variables instead of the process variables, thus providing the synthesis/design targets. The second reverse problem (reverse property prediction) solves the constitutive equations to identify unit operations, operating conditions and/or products by matching......This thesis describes the development of a general framework for solving process and product design problems. Targeting the desired performance of the system in a systematic manner relieves the iterative nature of conventional design techniques. Furthermore, conventional component based methods...... are not capable of handling problems, where the process or product objectives are driven by functionalities or properties rather than chemical constituency. The framework is meant to complement existing composition based methods by being able to handle property driven problems. By investigating the different...

  15. Muon System Design Studies for Detectors at CLIC

    CERN Document Server

    van der Kraaij, E

    2011-01-01

    The two concepts for CLIC detectors inherited their design of the muon systems from the ILC community. In this note the outcome of a reevaluation of the design for the CLIC environment is presented. Based on a full detector simulation, the muon identification performance is analysed for different detector layouts and different cellsizes. As a result, nine layers are suggested for the muon systems of the CLIC ILD and CLIC SiD detectors, which are arranged in three groups of three layers. The cellsizes have been kept at 30×30 mm2. These layouts are used for the performance studies of the CLIC Conceptual Design Report (CDR).

  16. Design Scheme of Remote Monitoring System Based on Qt

    Directory of Open Access Journals (Sweden)

    Xu Dawei

    2015-01-01

    Full Text Available This paper introduces a design scheme of remote monitoring system based on Qt, the scheme of remote monitoring system based on S3C2410 and Qt, with the aid of cross platform development tools Qt and powerful ARM platform design and implementation. The development of remote video surveillance system based on embedded terminal has practical significance and value.

  17. Initial trade and design studies for the fusion engineering device

    International Nuclear Information System (INIS)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-06-01

    The Magnetic Fusion Energy Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. The Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), initiated a program of trade and design studies in October 1980 to support the selection of the FED concept. This document presents the results of these initial trade and design studies. Based on these results, a baseline configuration has been identified and the Design Center effort for the remainder of the fiscal year will be devoted to the development of a self-consistent FED design description

  18. Designing Spreadsheet-Based Tasks for Purposeful Algebra

    Science.gov (United States)

    Ainley, Janet; Bills, Liz; Wilson, Kirsty

    2005-01-01

    We describe the design of a sequence of spreadsheet-based pedagogic tasks for the introduction of algebra in the early years of secondary schooling within the Purposeful Algebraic Activity project. This design combines two relatively novel features to bring a different perspective to research in the use of spreadsheets for the learning and…

  19. Teaching Database Design with Constraint-Based Tutors

    Science.gov (United States)

    Mitrovic, Antonija; Suraweera, Pramuditha

    2016-01-01

    Design tasks are difficult to teach, due to large, unstructured solution spaces, underspecified problems, non-existent problem solving algorithms and stopping criteria. In this paper, we comment on our approach to develop KERMIT, a constraint-based tutor that taught database design. In later work, we re-implemented KERMIT as EER-Tutor, and…

  20. Experiences in Preserving Design Bases & Knowledge Management

    International Nuclear Information System (INIS)

    Koshy, Thomas

    2013-01-01

    Purpose: • To build repository of information on design and development in a retrievable manner to: • Establish licensing/design bases of the plant; • Identify the known vulnerabilities and how they are to be addressed; • Prevent undoing the lessons learned; • Facilitate advancement without repeating the undesirable incidents of the past

  1. Model-Based Design of Tree WSNs for Decentralized Detection

    Directory of Open Access Journals (Sweden)

    Ashraf Tantawy

    2015-08-01

    Full Text Available The classical decentralized detection problem of finding the optimal decision rules at the sensor and fusion center, as well as variants that introduce physical channel impairments have been studied extensively in the literature. The deployment of WSNs in decentralized detection applications brings new challenges to the field. Protocols for different communication layers have to be co-designed to optimize the detection performance. In this paper, we consider the communication network design problem for a tree WSN. We pursue a system-level approach where a complete model for the system is developed that captures the interactions between different layers, as well as different sensor quality measures. For network optimization, we propose a hierarchical optimization algorithm that lends itself to the tree structure, requiring only local network information. The proposed design approach shows superior performance over several contentionless and contention-based network design approaches.

  2. Screening for type 2 diabetes in a high-risk population: Study design and feasibility of a population-based randomized controlled trial

    NARCIS (Netherlands)

    B. Klijs (Bart); S.J. Otto (Suzie); R.J. Heine (Robert); Y. van der Graaf (Yolanda); J.J. Lous (Jan); H.J. de Koning (Harry)

    2012-01-01

    textabstractBackground: We describe the design and present the results of the first year of a population-based study of screening for type 2 diabetes in individuals at high risk of developing the disease. High risk is defined as having abdominal obesity. Methods. Between 2006 and 2007, 79,142

  3. Design Based Research: the Way of Developing and Implementing Educational Innovation

    Directory of Open Access Journals (Sweden)

    Tina Štemberger

    2016-11-01

    Full Text Available The appropriate implementation of innovation is a crucial factor in improving educational practice. In the implementation process, there is, however, often a lack of interaction between designers and practitioners that would enable the latter to become competent enough to implement theoretical knowledge into practice and to have an ongoing support from designers. Design-based research is based on close cooperation between researchers, practitioners and designers which consequently allows greater integration of research and practice in education. In the present paper, the beginnings, development, basic characteristics, advantages, disadvantages and the research process of design-based research are reviewed and an example of design-based research is presented.

  4. The ERL-based Design of Electron-Hadron Collider eRHIC

    Energy Technology Data Exchange (ETDEWEB)

    Ptitsyn, Vadim [et al.

    2016-06-01

    Recent developments of the ERL-based design of future high-luminosity electron-hadron collider eRHIC focused on balancing technological risks present in the design versus the design cost. As a result a lower risk design has been adopted at moderate cost increase. The modifications include a change of the main linac RF frequency, reduced number of SRF cavity types and modified electron spin transport using a spin rotator. A luminosity-staged approach is being explored with a Nominal design ($L \\sim 10^{33} {\\rm cm}^2 {\\rm s}^{-1}$) that employs reduced electron current and could possibly be based on classical electron cooling, and then with the Ultimate design ($L \\gt 10^{34} {\\rm cm}^{-2} {\\rm s}^{-1}$) that uses higher electron current and an innovative cooling technique (CeC). The paper describes the recent design modifications, and presents the full status of the eRHIC ERL-based design.

  5. Michelson interferometer based interleaver design using classic IIR filter decomposition.

    Science.gov (United States)

    Cheng, Chi-Hao; Tang, Shasha

    2013-12-16

    An elegant method to design a Michelson interferometer based interleaver using a classic infinite impulse response (IIR) filter such as Butterworth, Chebyshev, and elliptic filters as a starting point are presented. The proposed design method allows engineers to design a Michelson interferometer based interleaver from specifications seamlessly. Simulation results are presented to demonstrate the validity of the proposed design method.

  6. Robins Air Force Base Solar Cogeneration Facility design

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, B.L.; Bodenschatz, C.A.

    1982-06-01

    A conceptual design and a cost estimate have been developed for a Solar Cogeneration Facility at Robins Air Force Base. This demonstration solar facility was designed to generate and deliver electrical power and process steam to the existing base distribution systems. The facility was to have the potential for construction and operation by 1986 and make use of existing technology. Specific objectives during the DOE funded conceptual design program were to: prepare a Solar Cogeneration Facility (overall System) Specification, select a preferred configuration and develop a conceptual design, establish the performance and economic characteristics of the facility, and prepare a development plan for the demonstration program. The Westinghouse team, comprised of the Westinghouse Advanced Energy Systems Division, Heery and Heery, Inc., and Foster Wheeler Solar Development Corporation, in conjunction with the U.S. Air Force Logistics Command and Georgia Power Company, has selected a conceptual design for the facility that will utilize the latest DOE central receiver technology, effectively utilize the energy collected in the application, operate base-loaded every sunny day of the year, and be applicable to a large number of military and industrial facilities throughout the country. The design of the facility incorporates the use of a Collector System, a Receiver System, an Electrical Power Generating System, a Balance of Facility - Steam and Feedwater System, and a Master Control System.

  7. A Framework for Effective User Interface Design for Web-Based Electronic Commerce Applications

    Directory of Open Access Journals (Sweden)

    Justyna Burns

    2001-01-01

    Full Text Available Efficient delivery of relevant product information is increasingly becoming the central basis of competition between firms. The interface design represents the central component for successful information delivery to consumers. However, interface design for web-based information systems is probably more an art than a science at this point in time. Much research is needed to understand properties of an effective interface for electronic commerce. This paper develops a framework identifying the relationship between user factors, the role of the user interface and overall system success for web-based electronic commerce. The paper argues that web-based systems for electronic commerce have some similar properties to decision support systems (DSS and adapts an established DSS framework to the electronic commerce domain. Based on a limited amount of research studying web browser interface design, the framework identifies areas of research needed and outlines possible relationships between consumer characteristics, interface design attributes and measures of overall system success.

  8. Computer-Aided Test Flow in Core-Based Design

    OpenAIRE

    Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

    2000-01-01

    This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of embedded cores. The CAT now is applied to a few cores within the Philips Core Test Pilot IC project

  9. Reliability-Based Robust Design Optimization of Structures Considering Uncertainty in Design Variables

    Directory of Open Access Journals (Sweden)

    Shujuan Wang

    2015-01-01

    Full Text Available This paper investigates the structural design optimization to cover both the reliability and robustness under uncertainty in design variables. The main objective is to improve the efficiency of the optimization process. To address this problem, a hybrid reliability-based robust design optimization (RRDO method is proposed. Prior to the design optimization, the Sobol sensitivity analysis is used for selecting key design variables and providing response variance as well, resulting in significantly reduced computational complexity. The single-loop algorithm is employed to guarantee the structural reliability, allowing fast optimization process. In the case of robust design, the weighting factor balances the response performance and variance with respect to the uncertainty in design variables. The main contribution of this paper is that the proposed method applies the RRDO strategy with the usage of global approximation and the Sobol sensitivity analysis, leading to the reduced computational cost. A structural example is given to illustrate the performance of the proposed method.

  10. Integrating Blended and Problem-Based Learning into an Architectural Housing Design Studio: A Case Study

    Science.gov (United States)

    Bregger, Yasemin Alkiser

    2017-01-01

    This paper presents how a blended learning pedagogic model is integrated into an architectural design studio by adapting the problem-based learning process and housing issues in Istanbul Technical University (ITU), during fall 2015 and spring 2016 semesters for fourth and sixth level students. These studios collaborated with the "Introduction…

  11. NuFact muon storage ring: study of a triangle design based on solenoid focusing decay straights

    Energy Technology Data Exchange (ETDEWEB)

    Meot, F. [Service Accelerateurs, Laboratoire de Physique Subatomique et de Cosmologie, Universite Joseph Fourier / CNRS-IN2P3, 53 Avenue des Martyrs, F-38026 Grenoble (France)]|[Commissariat a l' Energie Atomique, CEA, 31-33, rue de la Federation (Paris 15e), BP 510, 75752 Paris Cedex 15 (France); Reesy, G. [Rutherford Appleton Laboratory, Harwell Science and Innovation Campus, Didcot OX11 0QX (United Kingdom)

    2006-06-15

    Properties of acceptance and beam transmission in a triangle design of the neutrino factory muon decay ring, with decay straights based on solenoidal focusing, are reported.The muon storage ring in the neutrino factory, NuFact, is located at the high energy end of the muon acceleration chain. It delivers the {mu}{sup +}/{mu}{sup -} decay neutrinos to physics detectors. The design of concern here, is a triangle geometry 20 GeV storage ring, upgradable to 50 GeV, (the parameters are given), which features two decay straight sections, each one aiming at a distant detector. The third straight section of the ring is devoted to tuning, collimation and RF. A particularity of the proposed design, is in its being based on solenoid focusing decay straights, which has the virtue of minimizing the betatron amplitudes, compared to equivalent quadrupole focusing. The solenoidal focusing ensures the requested ratio, for the r.m.s. divergences of the 20 GeV muon and the neutrino beam, of 0.1 for an assumed muon normalized r.m.s. emittance of 4800 {pi} mm mr (3 {pi} cm, total). The goal of the present work is to show the viability of this design, in particular as concerns the impact of the solenoid focusing on machine behavior. It addresses the questions of residual coupling, machine acceptance, and concludes with a computation of beam transmission over 1000 turns. The paper has the following structure: 1. Introduction; 2. Working hypothesis; 3. Building-up ray-tracing data; 3.1. Arcs; 3.2. Solenoid straight; 3.3. Tuning/Collimation/RF straight; 3.4. Full ring; 3.4.1. Beam envelopes; 3.4.2. Closed orbits; 3.4.3. Momentum dispersion; 3.5 Large amplitude tracking, preliminary tests; 4. Tracking, linear machine; 4.1. Large amplitude tracking; 4.1.1. 2-D horizontal initial conditions; 4.1.2. 2-D vertical initial conditions; 4.1.3. 4-D + {delta}p/p initial conditions; 4.2. Transmission, 4-D + {delta}p/p, no sextupoles; 4.2.1. {epsilon}{sub x} {epsilon}{sub z} = 3 {pi} cm (norm.), {delta

  12. NuFact muon storage ring: study of a triangle design based on solenoid focusing decay straights

    International Nuclear Information System (INIS)

    Meot, F.; Reesy, G.

    2006-06-01

    Properties of acceptance and beam transmission in a triangle design of the neutrino factory muon decay ring, with decay straights based on solenoidal focusing, are reported.The muon storage ring in the neutrino factory, NuFact, is located at the high energy end of the muon acceleration chain. It delivers the μ + /μ - decay neutrinos to physics detectors. The design of concern here, is a triangle geometry 20 GeV storage ring, upgradable to 50 GeV, (the parameters are given), which features two decay straight sections, each one aiming at a distant detector. The third straight section of the ring is devoted to tuning, collimation and RF. A particularity of the proposed design, is in its being based on solenoid focusing decay straights, which has the virtue of minimizing the betatron amplitudes, compared to equivalent quadrupole focusing. The solenoidal focusing ensures the requested ratio, for the r.m.s. divergences of the 20 GeV muon and the neutrino beam, of 0.1 for an assumed muon normalized r.m.s. emittance of 4800 π mm mr (3 π cm, total). The goal of the present work is to show the viability of this design, in particular as concerns the impact of the solenoid focusing on machine behavior. It addresses the questions of residual coupling, machine acceptance, and concludes with a computation of beam transmission over 1000 turns. The paper has the following structure: 1. Introduction; 2. Working hypothesis; 3. Building-up ray-tracing data; 3.1. Arcs; 3.2. Solenoid straight; 3.3. Tuning/Collimation/RF straight; 3.4. Full ring; 3.4.1. Beam envelopes; 3.4.2. Closed orbits; 3.4.3. Momentum dispersion; 3.5 Large amplitude tracking, preliminary tests; 4. Tracking, linear machine; 4.1. Large amplitude tracking; 4.1.1. 2-D horizontal initial conditions; 4.1.2. 2-D vertical initial conditions; 4.1.3. 4-D + δp/p initial conditions; 4.2. Transmission, 4-D + δp/p, no sextupoles; 4.2.1. ε x ε z = 3 π cm (norm.), δp/p = ±1%; 4.2.2. ε x ε z = 6 π cm (norm.), δp/p ±4

  13. Implementation of knowledge-based engineering methodology in hydraulic generator design

    Directory of Open Access Journals (Sweden)

    Wei Guo

    2015-05-01

    Full Text Available Hydraulic generator design companies are always being exhorted to become more competitive by reducing the lead time and costs for their products for survival. Knowledge-based engineering technology is a rapidly developing technology with competitive advantage for design application to reduce time and cost in product development. This article addresses the structure of the hydraulic generator design system based on the knowledge-based engineering technology in detail. The system operates by creating a unified knowledge base to store the scattered knowledge among the whole life of the design process, which was contained in the expert’s brain and technical literature. It helps designers to make appropriate decisions by supplying necessary information at the right time through query and inference engine to represent the knowledge within the knowledge-based engineering application framework. It also integrates the analysis tools into one platform to help achieve global optimum solutions. Finally, an example of turbine-type selection was given to illustrate the operation process and prove its validity.

  14. Understandings of the Concept of Iteration in Design-Based Research

    DEFF Research Database (Denmark)

    Gundersen, Peter Bukovica

    2017-01-01

    The paper is the first in a series of papers addressing design in Design-based research. The series looks into the question of how this research approach is connected to design. What happens when educational researchers adopt designerly ways of working? This paper provides an overview of design......-based research and from there on discuss one key characteristic, namely iterations, which are fundamental to educational design research in relation to how designers operate and why. The paper concludes that in general iteration is not a particularly well-described aspect in the reporting of DBR-projects. Half...... and usually after long periods of testing design solutions in practice....

  15. Judgement of Design Scheme Based on Flexible Constraint in ICAD

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The conception of flexible constraint is proposed in the paper. The solution of flexible constraint is in special range, and maybe different in different instances of same design scheme. The paper emphasis on how to evaluate and optimize a design scheme with flexible constraints based on the satisfaction degree function defined on flexible constraints. The conception of flexible constraint is used to solve constraint conflict and design optimization in complicated constraint-based assembly design by the PFM parametrization assembly design system. An instance of gear-box design is used for verifying optimization method.

  16. Screening for type 2 diabetes in a high-risk population: study design and feasibility of a population-based randomized controlled trial

    NARCIS (Netherlands)

    Klijs, B.; Otto, S.J.; Heine, R.J.; van der Graaf, Y.; Lous, J.J.; Koning, H.J.

    2012-01-01

    Background: We describe the design and present the results of the first year of a population-based study of screening for type 2 diabetes in individuals at high risk of developing the disease. High risk is defined as having abdominal obesity. Methods. Between 2006 and 2007, 79,142 inhabitants of two

  17. Task-Based Method for Designing Underactuated Mechanisms

    Directory of Open Access Journals (Sweden)

    Shoichiro Kamada

    2012-03-01

    Full Text Available In this paper we introduce a task-based method for designing underactuated multi-joint prosthetic hands for specific grasping tasks. The designed robotic hands or prosthetic hands contain fewer independent actuators than joints. We chose a few specific grasping tasks that are frequently repeated in everyday life and analysed joint motions of the hand during the completion of each task and the level of participation of each joint. The information was used for the synthesis of dedicated underactuated mechanisms that can operate in a low dimensional task coordinate space. We propose two methods for reducing the actuators' number. The kinematic parameters of the synthesized mechanism are determined by using a numerical approach. In this study the joint angles of the synthesized hand are considered as linearly dependent on the displacements of the actuators. We introduced a special error index that allowed us to compare the original trajectory and the trajectory performed by the synthesized mechanism, and to select the kinematic parameters of the new kinematic structure as a way to reduce the error. The approach allows the design of simple gripper mechanisms with good accuracy for the preliminary defined tasks.

  18. Adjoint-Based Aerodynamic Design of Complex Aerospace Configurations

    Science.gov (United States)

    Nielsen, Eric J.

    2016-01-01

    An overview of twenty years of adjoint-based aerodynamic design research at NASA Langley Research Center is presented. Adjoint-based algorithms provide a powerful tool for efficient sensitivity analysis of complex large-scale computational fluid dynamics (CFD) simulations. Unlike alternative approaches for which computational expense generally scales with the number of design parameters, adjoint techniques yield sensitivity derivatives of a simulation output with respect to all input parameters at the cost of a single additional simulation. With modern large-scale CFD applications often requiring millions of compute hours for a single analysis, the efficiency afforded by adjoint methods is critical in realizing a computationally tractable design optimization capability for such applications.

  19. Designing and evaluating risk-based surveillance systems

    DEFF Research Database (Denmark)

    Willeberg, Preben; Nielsen, Liza Rosenbaum; Salman, Mo

    2012-01-01

    Risk-based surveillance systems reveal occurrence of disease or infection in a sample of population units, which are selected on the basis of risk factors for the condition under study. The purpose of such systems for supporting practical animal disease policy formulations and management decisions...... with prudent use of resources while maintaining acceptable system performance. High-risk category units are selected for testing by identification of the presence of specific high-risk factor(s), while disregarding other factors that might also influence the risk. On this basis we argue that the most...... applicable risk estimate for use in designing and evaluating a risk-based surveillance system would be a crude (unadjusted) relative risk, odds ratio or apparent prevalence. Risk estimates found in the published literature, however, are often the results of multivariable analyses implicitly adjusting...

  20. Design study on sodium-cooled middle-scale modular reactor

    International Nuclear Information System (INIS)

    Shimakawa, Yoshio; Nibe, Nobuaki; Hori, Toru

    2002-05-01

    In Phase 1 of the 'Feasibility Study on Commercialized Fast Reactor Cycle Systems (F/S)', an advanced loop type reactor has been selected as a promising concept of sodium-cooled middle-scale modular reactor, which has a possibility to fulfill the design requirements of the F/S. In Phase 2 of the F/S, it is planed to precede a preliminary conceptual design of a sodium-cooled middle-scale modular reactor based on the design of the advanced loop type reactor. Through the design study, it is intended to construct such a plant concept that can show its attraction and competitiveness as a commercialized reactor. This report summarizes the results of the design study on the sodium-cooled middle-scale modular reactor performed in JFY2001, which is the first year of Phase 2. As the construction cost of the sodium-cooled middle-scale modular reactor, which has been constructed in Phase 1, was about 10% higher than that of the sodium-cooled large-scale reactor, a new concept of the middle-scale modular reactor, which is expected to be equal to the large-scale reactor from a viewpoint of economic competitiveness, has been re-constructed based on the design of the advanced loop type reactor. After that, fundamental specifications of main systems and components for the new concept have been set, and critical subjects related to safety, structural integrity, thermal hydraulics, operability, maintainability and economy have been examined and evaluated. As a result of this study, the plant concept of the sodium-cooled middle-scale modular reactor has been constructed, which has a prospect to satisfy the economic goal (construction cost: less than 200,000 yens/kWe, etc.) and has a prospect to solve the critical subjects. From now on, reflecting the results of elemental experiments, the preliminary conceptual design of this plant will be preceded toward the selection for narrowing down candidate concepts at the end of Phase 2. (author)

  1. Place-Based Learning: Interactive Learning and Net-Zero Design

    Science.gov (United States)

    Holser, Alec; Becker, Michael

    2011-01-01

    Food and conservation science curriculum, net-zero design and student-based building performance monitoring have come together in the unique and innovative new Music and Science Building for Oregon's Hood River Middle School. The school's Permaculture-based curriculum both informed the building design and was also transformed through the…

  2. A Method of Numerical Control Equipment Appearance Design Based on Product Identity

    Science.gov (United States)

    Zhu, Zhijuan; Zhou, Qi; Li, Bin; Visser, Steve

    Research on numerical control (NC) equipment has been more and more abundant; however, there are few existing studies in the field of appearance design for NC equipments. This paper provided a method to generate new appearance design of NC equipments based on product identity (PI). For the purpose of providing guidelines to generate new concept of NC equipment design, this paper, therefore, took the DMG Company (a Germen NC equipment company) as a case, examined the total products of this company from two aspects: Product Image and Product Family. Task 1 was an evaluate task about the Product Image by using the semantic differential (SD) evaluation method; Task 2 was a study task about Product Family to find out features of the products and classify these features. During the Task 2, several features have been found out and summarized, and these features were classified into 3 different levels according to their frequency and importance. In the end, two appearance design samples have been generated based on the analysis above to prove the application of the research.

  3. Design of digital trapezoidal shaping filter based on LabVIEW

    International Nuclear Information System (INIS)

    Liu Yujuan; Qin Guoxiu; Yang Zhihui; Zhang Xiaodong

    2013-01-01

    It describes the design of a digital trapezoidal shaping filter to nuclear signals based on LabVIEW. A method of optimizing the trapezoidal shaping filter's parameters was presented and tested, and the test results of the effect of shaping filter algorithm were studied. (authors)

  4. A web-based adaptive tutor to teach PCR primer design

    NARCIS (Netherlands)

    van Seters, Janneke R.; Wellink, Joan; Tramper, Johannes; Goedhart, Martin J.; Ossevoort, Miriam A.

    2012-01-01

    When students have varying prior knowledge, personalized instruction is desirable. One way to personalize instruction is by using adaptive e-learning to offer training of varying complexity. In this study, we developed a web-based adaptive tutor to teach PCR primer design: the PCR Tutor. We used

  5. A Web-based Adaptive Tutor to Teach PCR Primer Design

    NARCIS (Netherlands)

    Seters, van J.R.; Wellink, J.; Tramper, J.; Goedhart, M.J.; Ossevoort, M.A.

    2012-01-01

    When students have varying prior knowledge, personalized instruction is desirable. One way to personalize instruction is by using adaptive e-learning to offer training of varying complexity. In this study, we developed a web-based adaptive tutor to teach PCR primer design: the PCR Tutor. We used

  6. Implementing healthcare excellence: the vital role of the CEO in evidence-based design.

    Science.gov (United States)

    Zimring, Craig; Augenbroe, Godfried L; Malone, Eileen B; Sadler, Blair L

    2008-01-01

    This paper explores the role of the chief executive officer (CEO) in evidence-based design (EBD), discussing the internal and external challenges that a CEO faces, such as demands for increased quality, safety, patient-and-family-centeredness, increased revenue, and reduced cost. Based on a series of interviews and case studies and the experience of the authors as researchers, consultants, and CEOs, this paper provides a model for EBD and recommends actions that a CEO can undertake to create an effective project over the life cycle of a building. TOPICAL HEADINGS: Evidence-Based Design: A Performance-Based Approach to Achieving Key Goals; Key Approaches to Executing Evidence-Based Design; Overcoming Barriers to Innovation: The CEO's Vital Role in Implementing Evidence-Based Design The CEO bears special responsibility for successful facility project implementation. Only the CEO possesses the responsibility and authority to articulate the strategy, vision, goals, and resource constraints that frame every project. With the support of their boards, CEOs set the stage for the transformation of an organization's culture and fuel clinical and business process reengineering by encouraging and, if necessary, forcing collaboration between the strong disciplinary and departmental divisions found in healthcare systems.

  7. Agent-Based Coordination Model for Designing Transportation Applications

    OpenAIRE

    BADEIG, F; BALBO, F; SCEMAMA, G; ZARGAYOUNA, M

    2008-01-01

    This paper presents an environment-centered approach to design multi-agent solutions to transportation problems. Based on the Property-based Coordination Principle (PbC), the objective of our approach is to solve three recurrent issues in the design of these solutions: the knowledge problem, the space-time dimension and the dynamics of the real environment. To demonstrate the benefits of our approach, two completely different applications, a demand-responsive transportation system and a simul...

  8. Conceptual design study of fusion experimental reactor (FY86 FER)

    International Nuclear Information System (INIS)

    Miki, Nobuharu; Iida, Fumio; Suzuki, Shohei; Wachi, Yoshihiro; Toyoda, Katsuyoshi; Hashizume, Takashi; Konno, Masayuki.

    1987-09-01

    This report summarizes the FER magnet design which was conducted last year (1986). Main objective of the new FER design is to have better cost performance of the machine. The physics assumptions are reviewed to reduce risks. Optimization of the physics design and improvements of the engineering design have been done without changing missions of the device. After a preliminary investigation for the optimization and improvements, six FER concepts have been developed to establish the improved design point, and have been studied in more detail. In the magnet design, the improvements of superconducting magnet design were mainly investigated to reduce the reactor size. A normal conductor was studied as an alternative option for appling to the special poloidal field coils that were located on the interior to the toroidal field coils. Some improvements were made on the superconducting magnet design. Based on the preliminary investigation, the magnet design specifications have been modified somewhat. The conceptual design of the magnet system components have been done for the candidate FER concepts. (author)

  9. Feature-based component model for design of embedded systems

    Science.gov (United States)

    Zha, Xuan Fang; Sriram, Ram D.

    2004-11-01

    An embedded system is a hybrid of hardware and software, which combines software's flexibility and hardware real-time performance. Embedded systems can be considered as assemblies of hardware and software components. An Open Embedded System Model (OESM) is currently being developed at NIST to provide a standard representation and exchange protocol for embedded systems and system-level design, simulation, and testing information. This paper proposes an approach to representing an embedded system feature-based model in OESM, i.e., Open Embedded System Feature Model (OESFM), addressing models of embedded system artifacts, embedded system components, embedded system features, and embedded system configuration/assembly. The approach provides an object-oriented UML (Unified Modeling Language) representation for the embedded system feature model and defines an extension to the NIST Core Product Model. The model provides a feature-based component framework allowing the designer to develop a virtual embedded system prototype through assembling virtual components. The framework not only provides a formal precise model of the embedded system prototype but also offers the possibility of designing variation of prototypes whose members are derived by changing certain virtual components with different features. A case study example is discussed to illustrate the embedded system model.

  10. Design and implementation of a project-based active/cooperative engineering design course for freshmen

    Science.gov (United States)

    Abdulaal, R. M.; Al-Bahi, A. M.; Soliman, A. Y.; Iskanderani, F. I.

    2011-08-01

    A project-based active/cooperative design course is planned, implemented, assessed and evaluated to achieve several desired engineering outcomes. The course allows freshman-level students to gain professional hands-on engineering design experience through an opportunity to practise teamwork, quality principles, communication skills, life-long learning, realistic constraints and awareness of current domestic and global challenges. Throughout successive design reports and in-class assignments, the students are required by the end of the semester to communicate, clearly and concisely, the details of their design both orally and in writing through a functional artefact/prototype, a design notebook, an A0 project poster and a final oral presentation. In addition to these direct assessment tools, several indirect measures are used to ensure triangulation. Assignments are based on customer expectations using a detailed checklist. This paper shows the direct and indirect assessment tools that indicated a high level of achievement of course learning outcomes and a high level of student satisfaction.

  11. A comparison of an energy/economic-based against an exergoeconomic-based multi-objective optimisation for low carbon building energy design

    International Nuclear Information System (INIS)

    García Kerdan, Iván; Raslan, Rokia; Ruyssevelt, Paul; Morillón Gálvez, David

    2017-01-01

    This study presents a comparison of the optimisation of building energy retrofit strategies from two different perspectives: an energy/economic-based analysis and an exergy/exergoeconomic-based analysis. A recently retrofitted community centre is used as a case study. ExRET-Opt, a novel building energy/exergy simulation tool with multi-objective optimisation capabilities based on NSGA-II is used to run both analysis. The first analysis, based on the 1st Law only, simultaneously optimises building energy use and design's Net Present Value (NPV). The second analysis, based on the 1st and the 2nd Laws, simultaneously optimises exergy destructions and the exergoeconomic cost-benefit index. Occupant thermal comfort is considered as a common objective function for both approaches. The aim is to assess the difference between the methods and calculate the performance among main indicators, considering the same decision variables and constraints. Outputs show that the inclusion of exergy/exergoeconomics as objective functions into the optimisation procedure has resulted in similar 1st Law and thermal comfort outputs, while providing solutions with less environmental impact under similar capital investments. This outputs demonstrate how the 1st Law is only a necessary calculation while the utilisation of the 1st and 2nd Laws becomes a sufficient condition for the analysis and design of low carbon buildings. - Highlights: • The study compares an energy-based and an exergy-based building design optimisation. • Occupant thermal comfort is considered as a common objective function. • A comparison of thermodynamic outputs is made against the actual retrofit design. • Under similar constraints, second law optimisation presents better overall results. • Exergoeconomic optimisation solutions improves building exergy efficiency to double.

  12. Analysis and Design of Web-Based Database Application for Culinary Community

    Directory of Open Access Journals (Sweden)

    Choirul Huda

    2017-03-01

    Full Text Available This research is based on the rapid development of the culinary and information technology. The difficulties in communicating with the culinary expert and on recipe documentation make a proper support for media very important. Therefore, a web-based database application for the public is important to help the culinary community in communication, searching and recipe management. The aim of the research was to design a web-based database application that could be used as social media for the culinary community. This research used literature review, user interviews, and questionnaires. Moreover, the database system development life cycle was used as a guide for designing a database especially for conceptual database design, logical database design, and physical design database. Web-based application design used eight golden rules for user interface design. The result of this research is the availability of a web-based database application that can fulfill the needs of users in the culinary field related to communication and recipe management.

  13. Study Of Lampungnese Traditional Home Garden Design

    Science.gov (United States)

    Pratiwi, R. A.; Gunawan

    2017-10-01

    Lampung is one area in Indonesia which has a traditional culture that comes from two groups of descents, they are ulun Lampung Pepadun and ulun Lampung Saibatin. Lampungnese traditional culture has been well-known by Indonesian people for its traditional dances, traditional clothing, or traditional home architecture. However, Lampungnese traditional home garden recently may not yet been described. Information related to Lampungnese traditional home garden is still very limited and it does not yet represented the culture based design concept. This research was directed to identify the elements of the home garden and map it into design concept of the Lampungnese traditional home garden based on information of Lampungnese traditional culture. The study was conducted by using descriptive approach through literature review, interviews and cultural exploration, as well as field observation. The study was able to identify the elements forming the Lampungnese traditional home garden, namely gakhang hadap, walai, outdoor kitchenette, firewood place, outdoor kitchen, livestock barns, as well as plants. Space layout of the home garden comprises front yard (tengahbah/terambah/beruan), side yard (kebik/kakebik), and backyard (kudan/juyu/kebon). Each element of the garden is located in the right place of the space layout.

  14. Computer aided design of nickel-base superalloys

    International Nuclear Information System (INIS)

    Lawrence, P.J.

    1988-01-01

    This paper describes a computer aided design process for Ni-base superalloys developed and employed at ASEA Brown Boveri. The technique involves a series of modules each of which predicts a particular property of a hypothetical new composition. In the first stage of the development of this design techniques modules were produced to predict phase stability, using PHACOMP, and high temperature creep strength and hot corrosion resistance, using multiple linear regression equations derived from the data in the literature. Alloys designed using these technique are also discussed and, in particular, shortcomings of the design process are highlighted. This information was then used to produce a revamped design methodology involving extra modules, including prediction of an alloy's gamma-prime content. (orig.)

  15. [In silico CRISPR-based sgRNA design].

    Science.gov (United States)

    Wang, Yuanli; Chuai, Guohui; Yan, Jifang; Shi, Lei; Liu, Qi

    2017-10-25

    CRISPR-based genome editing has been widely implemented in various cell types. In-silico single guide RNA (sgRNA) design is a key step for successful gene editing using CRISPR system. Continuing efforts are made to refine in-silico sgRNA design with high on-target efficacy and reduced off-target effects. In this paper, we summarize the present sgRNA design tools, and show that efficient in-silico models can be built that integrate current heterogeneous genome-editing data to derive unbiased sgRNA design rules and identify key features for improving sgRNA design. Our review shows that systematic comparisons and evaluation of on-target and off-target effects of sgRNA will allow more precise genome editing and gene therapies using the CRISPR system.

  16. Probability based load factors for design of concrete containment structures

    International Nuclear Information System (INIS)

    Hwang, H.; Kagami, S.; Reich, M.; Ellingwood, B.; Shinozuka, M.

    1985-01-01

    This paper describes a procedure for developing probability-based load combinations for the design of concrete containments. The proposed criteria are in a load and resistance factor design (LRFD) format. The load factors and resistance factors are derived for use in limit states design and are based on a target limit state probability. In this paper, the load factors for accident pressure and safe shutdown earthquake are derived for three target limit state probabilities. Other load factors are recommended on the basis of prior experience with probability-based design criteria for ordinary building construction. 6 refs

  17. Research and design of logistical information system based on SOA

    Science.gov (United States)

    Zhang, Bo

    2013-03-01

    Through the study on the existing logistics information systems and SOA technology, based on the current situation of enterprise logistics management and business features, this paper puts forward a SOA-based logistics system design program. This program is made in the WCF framework, with the combination of SOA and the actual characteristics of logistics enterprises, is simple to realize, easy to operate, and has strong expansion characteristic, therefore has high practical value.

  18. Re-design of ITER Glow Discharge Cleaning system based on a fixed electrode concept

    International Nuclear Information System (INIS)

    Yang, Y.; Maruyama, S.; Kiss, G.; O’Connor, M.; Zhang, Y.; Pitts, R.A.; Shimada, M.; Fang, T.; Wang, Y.; Wang, M.; Pan, Y.; Li, B.; Li, L.

    2014-01-01

    Highlights: •This paper summarizes the approved new design of ITER GDC. •It is based on the fixed electrode design instead of the previous movable concept. •Estimates were made on the glow current density. •R and D topics on initiation, steady state and heat load were presented. •Other relevant considerations were listed in an exhaustive manner. -- Abstract: A new design of ITER Glow Discharge Cleaning (GDC) system based on a fixed electrode concept replaces the previous design which was based on a movable electrode integrated with the ITER In-Vessel-Viewing-System. Recently the conceptual design of the GDC system was reviewed successfully on the functions, safety, operation and maintenance. The design proposed was checked against the requirements and found to be feasible. This paper gives an overall description of the requirements from physics and operation viewpoints and introduces the design at the conceptual level. Main R and D activities are listed and summarized. Further detailed studies are to be performed in the following design stage

  19. A cell-based design approach for RSFQ circuits using a binary decision diagram

    International Nuclear Information System (INIS)

    Yoshikawa, N.; Koshiyama, J.

    1999-01-01

    We propose a cell-based design approach for rapid single flux quantum (RSFQ) circuits based on a binary decision diagram (BDD). The BDD is a way to represent a logical function using a directed graph which consists of binary switches having one input and two outputs. Since complex logic circuits can be implemented in the form of regular arrays of the BDD binary switches, we can use a cell-based layout methodology for the design of the RSFQ circuits. In this study, we implemented the BDD binary switches by a D 2 flip-flop. In the BDD design approach we made a cell library which contains a binary switch, pulse splitters, confluence buffers and Josephson transmission lines. All cell layouts in the library have identical widths and heights, so that any logic function can be laid out by simple connection of the library cells. As a case study, we implemented a 1-bit RSFQ half-adder and a 3-bit encoder for a flash AD converter. (author)

  20. A Clinical Reasoning Tool for Virtual Patients: Design-Based Research Study.

    Science.gov (United States)

    Hege, Inga; Kononowicz, Andrzej A; Adler, Martin

    2017-11-02

    Clinical reasoning is a fundamental process medical students have to learn during and after medical school. Virtual patients (VP) are a technology-enhanced learning method to teach clinical reasoning. However, VP systems do not exploit their full potential concerning the clinical reasoning process; for example, most systems focus on the outcome and less on the process of clinical reasoning. Keeping our concept grounded in a former qualitative study, we aimed to design and implement a tool to enhance VPs with activities and feedback, which specifically foster the acquisition of clinical reasoning skills. We designed the tool by translating elements of a conceptual clinical reasoning learning framework into software requirements. The resulting clinical reasoning tool enables learners to build their patient's illness script as a concept map when they are working on a VP scenario. The student's map is compared with the experts' reasoning at each stage of the VP, which is technically enabled by using Medical Subject Headings, which is a comprehensive controlled vocabulary published by the US National Library of Medicine. The tool is implemented using Web technologies, has an open architecture that enables its integration into various systems through an open application program interface, and is available under a Massachusetts Institute of Technology license. We conducted usability tests following a think-aloud protocol and a pilot field study with maps created by 64 medical students. The results show that learners interact with the tool but create less nodes and connections in the concept map than an expert. Further research and usability tests are required to analyze the reasons. The presented tool is a versatile, systematically developed software component that specifically supports the clinical reasoning skills acquisition. It can be plugged into VP systems or used as stand-alone software in other teaching scenarios. The modular design allows an extension with new

  1. Data base pertinent to earthquake design basis

    International Nuclear Information System (INIS)

    Sharma, R.D.

    1988-01-01

    Mitigation of earthquake risk from impending strong earthquakes is possible provided the hazard can be assessed, and translated into appropriate design inputs. This requires defining the seismic risk problem, isolating the risk factors and quantifying risk in terms of physical parameters, which are suitable for application in design. Like all other geological phenomena, past earthquakes hold the key to the understanding of future ones. Quantificatio n of seismic risk at a site calls for investigating the earthquake aspects of the site region and building a data base. The scope of such investigations is il lustrated in Figure 1 and 2. A more detailed definition of the earthquake problem in engineering design is given elsewhere (Sharma, 1987). The present document discusses the earthquake data base, which is required to support a seismic risk evaluation programme in the context of the existing state of the art. (author). 8 tables, 10 figs., 54 refs

  2. Development of a tool for knowledge base verification of expert system based on Design/CPN

    International Nuclear Information System (INIS)

    Kim, Jong Hyun

    1998-02-01

    Verification is a necessary work in developing a reliable expert system. Verification is a process aimed at demonstrating whether a system meets it's specified requirements. As expert systems are used in various applications, the knowledge base verification of systems takes an important position. The conventional Petri net approach that has been studied recently in order to verify the knowledge base is found that it is inadequate to verify the knowledge base of large and complex system, such as alarm processing system of nuclear power plant. Thus, we propose an improved method that models the knowledge base as enhanced colored Petri net. In this study, we analyze the reachability and the error characteristics of the knowledge base. Generally, verification process requires computational support by automated tools. For this reason, this study developed a tool for knowledge base verification based on Design/CPN, which is a tool for editing, modeling, and simulating Colored Petri net. This tool uses Enhanced Colored Petri net as a modeling method. By applying this tool to the knowledge base of nuclear power plant, it is noticed that it can successfully check most of the anomalies that can occur in a knowledge base

  3. Designing a Consequentially Based Study into the Online Support of Pre-Service Teachers in the UK

    Science.gov (United States)

    Kontopoulou, Konstantina; Fox, Alison

    2015-01-01

    This paper reports on the design of a pilot doctoral study into the online support of pre-service teachers. It highlights the significance of a consequential, rather than deontological, perspective in guiding the development of a study's design. The study initially aimed to explore pre-service teachers' perceptions and use of social media on their…

  4. Novel measurement-based indoor cellular radio system design

    OpenAIRE

    Aragón-Zavala, A

    2008-01-01

    A scaleable, measurement-based radio methodology has been created to use for the design, planing and optimisation of in door cellular radio systems. The development of this measurement-based methodology was performed having in mind that measurements are of ten required to valiate radio coverage in a building. Therefore, the concept of using care fully calibrated measurements to design and optimise a system is feasible since these measurements can easily be obtained prior to system deployment ...

  5. Property Model-based Tailor-made Design of Chemical-based Products

    DEFF Research Database (Denmark)

    Kalakul, Sawitree

    Computer-aided model-based methods and tools are increasingly playing important roles in chemical product design. They have the potential to very quickly search for and identify reliable product candidates that can then be verified through experiments. Inthis way, the time and resources spent...... on experiment are reduced leading to faster and cheaper to market the products. The tools also help to manage the solution of product design problems, which usually require efficient handling of model-data-knowledge from different sources and at different time and size scales. The main contribution...... the needed template for a desired product is not available. VPPD-Lab employs a suite of algorithms(such as database search, molecular and mixture blend design) and toolboxes (such asproperty calculations and property model consistency tests) for specific product property prediction, design, and/or analysis...

  6. Community-based co-design in Okomakuara

    DEFF Research Database (Denmark)

    Kapuire, Gereon Koch; Winschiers-Theophilus, Heike; Chivuno-Kuria, Shilumbe

    2014-01-01

    Although the wider motivation and principles of Participatory Design (PD) are universal its concepts and techniques are highly contextual. Community-based codesign is a variation of PD, where processes are negotiated within the interaction. Thus this workshop gives participants the opportunity...

  7. A Representation System User Interface for Knowledge Base Designers

    OpenAIRE

    Fikes, Richard E.

    1982-01-01

    A major strength of frame-based knowledge representation languages is their ability to provide the knowledge base designer with a concise and intuitively appealing means expression. The claim of intuitive appeal is based on the observation that the object -centered style of description provided by these languages often closely matches a designer's understanding of the domain being modeled and therefore lessens the burden of reformulation involved in developing a formal description. To be effe...

  8. Learning Axes and Bridging Tools in a Technology-Based Design for Statistics

    Science.gov (United States)

    Abrahamson, Dor; Wilensky, Uri

    2007-01-01

    We introduce a design-based research framework, "learning axes and bridging tools," and demonstrate its application in the preparation and study of an implementation of a middle-school experimental computer-based unit on probability and statistics, "ProbLab" (Probability Laboratory, Abrahamson and Wilensky 2002 [Abrahamson, D., & Wilensky, U.…

  9. [Designing and implementation of a web-based quality monitoring system for plasma glucose measurement in multicenter population study].

    Science.gov (United States)

    Liu, Yong; Wang, Limin; Pang, Richard; Mo, Nanxun; Hu, Yan; Deng, Qian; Hu, Zhaohui

    2015-05-01

    The aim of this paper is to describe the designing and implementation of a web-based plasma glucose measurement quality monitoring system to assess the analytical quality of plasma glucose measurements in multicenter population study and provide evidence for the future studies. In the chronic non-communicable disease and related factor surveillance in China, a web based quality monitoring system for plasma glucose measurement was established to conduct evaluation on plasma glucose monitoring quality and effectiveness in 302 surveillance centers, including quality control data entry, transmission and feedback. The majority of the surveillance centers met the quality requirements and passed the evaluation of reproducibility and precision of plasma glucose measurement, only a few centers required intensive training and re-assessment. In order to ensure the completeness and reliability of plasma glucose measurement in the surveillance centers, the establishment of web-based plasma glucose measurement quality control system can facilitate the identification of the qualified surveillance centers and evaluation of plasma glucose measurement quality in different regions. Communication and training are important in ensuring plasma glucose measurement quality. It is necessary to further improve this web-based plasma glucose measurement quality monitoring system in the future to reduce the method specific plasma glucose measurement bias.

  10. Medicinal Chemistry Projects Requiring Imaginative Structure-Based Drug Design Methods.

    Science.gov (United States)

    Moitessier, Nicolas; Pottel, Joshua; Therrien, Eric; Englebienne, Pablo; Liu, Zhaomin; Tomberg, Anna; Corbeil, Christopher R

    2016-09-20

    Computational methods for docking small molecules to proteins are prominent in drug discovery. There are hundreds, if not thousands, of documented examples-and several pertinent cases within our research program. Fifteen years ago, our first docking-guided drug design project yielded nanomolar metalloproteinase inhibitors and illustrated the potential of structure-based drug design. Subsequent applications of docking programs to the design of integrin antagonists, BACE-1 inhibitors, and aminoglycosides binding to bacterial RNA demonstrated that available docking programs needed significant improvement. At that time, docking programs primarily considered flexible ligands and rigid proteins. We demonstrated that accounting for protein flexibility, employing displaceable water molecules, and using ligand-based pharmacophores improved the docking accuracy of existing methods-enabling the design of bioactive molecules. The success prompted the development of our own program, Fitted, implementing all of these aspects. The primary motivation has always been to respond to the needs of drug design studies; the majority of the concepts behind the evolution of Fitted are rooted in medicinal chemistry projects and collaborations. Several examples follow: (1) Searching for HDAC inhibitors led us to develop methods considering drug-zinc coordination and its effect on the pKa of surrounding residues. (2) Targeting covalent prolyl oligopeptidase (POP) inhibitors prompted an update to Fitted to identify reactive groups and form bonds with a given residue (e.g., a catalytic residue) when the geometry allows it. Fitted-the first fully automated covalent docking program-was successfully applied to the discovery of four new classes of covalent POP inhibitors. As a result, efficient stereoselective syntheses of a few screening hits were prioritized rather than synthesizing large chemical libraries-yielding nanomolar inhibitors. (3) In order to study the metabolism of POP inhibitors by

  11. A Simulation-Based LED Design Project in Photonics Instruction Based on Industry-University Collaboration

    Science.gov (United States)

    Chang, S. -H.; Chen, M. -L.; Kuo, Y. -K.; Shen, Y. -C.

    2011-01-01

    In response to the growing industrial demand for light-emitting diode (LED) design professionals, based on industry-university collaboration in Taiwan, this paper develops a novel instructional approach: a simulation-based learning course with peer assessment to develop students' professional skills in LED design as required by industry as well as…

  12. Preliminary studi on neutronic aspect of a conceptual design of the Kartini reactor base ADS facility

    International Nuclear Information System (INIS)

    Tegas Sutondo

    2012-01-01

    A preliminary study on neutronic aspect of a conceptual design of ADS facility with the basis of Kartini Reaktor, has been performed. The study was intended to see the feasibility from neutronic point of view of Kartini reactor, to be used as a small scale of NPP’s waste transmutation experimental facility. A SRAC code was used as the basis of calculations. The results indicate that the presence of minor actinides (MA) will give a positive reactivity, which tends to increase with the increase of MA concentrations. Based on the defined criteria of subcriticality and by considering the core power distributions and the level of reactivity contribution of MA element, it is concluded that Kartini reactor is potential enough to be used as an ADS experimental facility, mainly for MA concentration between 30 to 50 % of the assumed mixture of C-MA matrix. (author)

  13. AFB/open cycle gas turbine conceptual design study

    Science.gov (United States)

    Dickinson, T. W.; Tashjian, R.

    1983-09-01

    Applications of coal fired atmospheric fluidized bed gas turbine systems in industrial cogeneration are identified. Based on site-specific conceptual designs, the potential benefits of the AFB/gas turbine system were compared with an atmospheric fluidized design steam boiler/steam turbine system. The application of these cogeneration systems at four industrial plant sites is reviewed. A performance and benefit analysis was made along with a study of the representativeness of the sites both in regard to their own industry and compared to industry as a whole. A site was selected for the conceptual design, which included detailed site definition, AFB/gas turbine and AFB/steam turbine cogeneration system designs, detailed cost estimates, and comparative performance and benefit analysis. Market and benefit analyses identified the potential market penetration for the cogeneration technologies and quantified the potential benefits.

  14. Home-based versus hospital-based cardiac rehabilitation after myocardial infarction or revascularisation: design and rationale of the Birmingham Rehabilitation Uptake Maximisation Study (BRUM: a randomised controlled trial [ISRCTN72884263

    Directory of Open Access Journals (Sweden)

    Lane Deirdre

    2003-09-01

    Full Text Available Abstract Background Cardiac rehabilitation following myocardial infarction reduces subsequent mortality, but uptake and adherence to rehabilitation programmes remains poor, particularly among women, the elderly and ethnic minority groups. Evidence of the effectiveness of home-based cardiac rehabilitation remains limited. This trial evaluates the effectiveness and cost-effectiveness of home-based compared to hospital-based cardiac rehabilitation. Methods/design A pragmatic randomised controlled trial of home-based compared with hospital-based cardiac rehabilitation in four hospitals serving a multi-ethnic inner city population in the United Kingdom was designed. The home programme is nurse-facilitated, manual-based using the Heart Manual. The hospital programmes offer comprehensive cardiac rehabilitation in an out-patient setting. Patients We will randomise 650 adult, English or Punjabi-speaking patients of low-medium risk following myocardial infarction, coronary angioplasty or coronary artery bypass graft who have been referred for cardiac rehabilitation. Main outcome measures Serum cholesterol, smoking cessation, blood pressure, Hospital Anxiety and Depression Score, distance walked on Shuttle walk-test measured at 6, 12 and 24 months. Adherence to the programmes will be estimated using patient self-reports of activity. In-depth interviews with non-attendees and non-adherers will ascertain patient views and the acceptability of the programmes and provide insights about non-attendance and aims to generate a theory of attendance at cardiac rehabilitation. The economic analysis will measure National Health Service costs using resource inputs. Patient costs will be established from the qualitative research, in particular how they affect adherence. Discussion More data are needed on the role of home-based versus hospital-based cardiac rehabilitation for patients following myocardial infarction and revascularisation, which would be provided by the

  15. Risk based seismic design criteria

    International Nuclear Information System (INIS)

    Kennedy, R.P.

    1999-01-01

    In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2) What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the safe-shutdown-earthquake (SSE) ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented. (orig.)

  16. Impact of an engineering design-based curriculum compared to an inquiry-based curriculum on fifth graders' content learning of simple machines

    Science.gov (United States)

    Marulcu, Ismail; Barnett, Michael

    2016-01-01

    Background: Elementary Science Education is struggling with multiple challenges. National and State test results confirm the need for deeper understanding in elementary science education. Moreover, national policy statements and researchers call for increased exposure to engineering and technology in elementary science education. The basic motivation of this study is to suggest a solution to both improving elementary science education and increasing exposure to engineering and technology in it. Purpose/Hypothesis: This mixed-method study examined the impact of an engineering design-based curriculum compared to an inquiry-based curriculum on fifth graders' content learning of simple machines. We hypothesize that the LEGO-engineering design unit is as successful as the inquiry-based unit in terms of students' science content learning of simple machines. Design/Method: We used a mixed-methods approach to investigate our research questions; we compared the control and the experimental groups' scores from the tests and interviews by using Analysis of Covariance (ANCOVA) and compared each group's pre- and post-scores by using paired t-tests. Results: Our findings from the paired t-tests show that both the experimental and comparison groups significantly improved their scores from the pre-test to post-test on the multiple-choice, open-ended, and interview items. Moreover, ANCOVA results show that students in the experimental group, who learned simple machines with the design-based unit, performed significantly better on the interview questions. Conclusions: Our analyses revealed that the design-based Design a people mover: Simple machines unit was, if not better, as successful as the inquiry-based FOSS Levers and pulleys unit in terms of students' science content learning.

  17. Design of patterned sapphire substrates for GaN-based light-emitting diodes

    International Nuclear Information System (INIS)

    Wang Hai-Yan; Lin Zhi-Ting; Han Jing-Lei; Zhong Li-Yi; Li Guo-Qiang

    2015-01-01

    A new method for patterned sapphire substrate (PSS) design is developed and proven to be reliable and cost-effective. As progress is made with LEDs’ luminous efficiency, the pattern units of PSS become more complicated, and the effect of complicated geometrical features is almost impossible to study systematically by experiments only. By employing our new method, the influence of pattern parameters can be systematically studied, and various novel patterns are designed and optimized within a reasonable time span, with great improvement in LEDs’ light extraction efficiency (LEE). Clearly, PSS pattern design with such a method deserves particular attention. We foresee that GaN-based LEDs on these newly designed PSSs will achieve more progress in the coming years. (topical review)

  18. Gear hot forging process robust design based on finite element method

    International Nuclear Information System (INIS)

    Xuewen, Chen; Won, Jung Dong

    2008-01-01

    During the hot forging process, the shaping property and forging quality will fluctuate because of die wear, manufacturing tolerance, dimensional variation caused by temperature and the different friction conditions, etc. In order to control this variation in performance and to optimize the process parameters, a robust design method is proposed in this paper, based on the finite element method for the hot forging process. During the robust design process, the Taguchi method is the basic robust theory. The finite element analysis is incorporated in order to simulate the hot forging process. In addition, in order to calculate the objective function value, an orthogonal design method is selected to arrange experiments and collect sample points. The ANOVA method is employed to analyze the relationships of the design parameters and design objectives and to find the best parameters. Finally, a case study for the gear hot forging process is conducted. With the objective to reduce the forging force and its variation, the robust design mathematical model is established. The optimal design parameters obtained from this study indicate that the forging force has been reduced and its variation has been controlled

  19. Design Transformation based on Nature and Identity Formation in the Design of Landscape Elements

    Directory of Open Access Journals (Sweden)

    Zulkifli Muslim

    2016-01-01

    Full Text Available There is a lack of initiative from the designers to integrate the environmental resources in the material and design production of local urban landscape elements that reflects human culture and lifestyle. Based on criteria and principles of symbol design and transformation process, this paper describes the symbiotic relationship between local plants (flower and designs of landscape elements. Using visual analysis, the researcher manipulated shapes and forms of local plant images in producing possible shapes and forms for a design of landscape element (lamp post. The results indicate that the design transformation is a systematic process that allows for variations in design without losing the core characteristics and identity of the basic elements of nature.

  20. Reliability-Based Design Optimization of Trusses with Linked-Discrete Design Variables using the Improved Firefly Algorithm

    Directory of Open Access Journals (Sweden)

    N. M. Okasha

    2016-04-01

    Full Text Available In this paper, an approach for conducting a Reliability-Based Design Optimization (RBDO of truss structures with linked-discrete design variables is proposed. The sections of the truss members are selected from the AISC standard tables and thus the design variables that represent the properties of each section are linked. Latin hypercube sampling is used in the evaluation of the structural reliability. The improved firefly algorithm is used for the optimization solution process. It was found that in order to use the improved firefly algorithm for efficiently solving problems of reliability-based design optimization with linked-discrete design variables; it needs to be modified as proposed in this paper to accelerate its convergence.

  1. VXIbus data collection system -- A design study

    International Nuclear Information System (INIS)

    Hacker, U.; Richter, B.; Weinert, A.; Arlt, R.; Lewis, W.; Swinhoe, M.

    1995-01-01

    The German support program has sponsored the work to investigate the VXIbus as integration platform for safeguards instrumentation. This paper will cover the analysis of the user requirements for a VXIbus based monitoring system for integrated safeguards -- primarily for reliable unattended in-field collection of large amounts of data. The goal is to develop a suitable system architecture. The design of the system makes use of the VXIbus standard as the selected hardware platform Based upon the requirement analysis and the overriding need for high reliability and robustness, a systematic investigation of different operating system options, as well as development and integration tools will be considered. For the software implementation cycle high and low level programming tools are required. The identification of the constraints for the programming platform and the tool selection will be presented. Both the strategic approach, the rules for analysis and design work as well as the executive components for the support of the implementation and production cycle are given. Here all the conditions for reliable, unattended and integrated safeguards monitoring systems will be addressed. The definition of the basic and advanced design principles are covered. The paper discusses the results of a study on a system produced to demonstrate a high data rate timer/counter application

  2. Rough Set Theory Based Fuzzy TOPSIS on Serious Game Design Evaluation Framework

    Directory of Open Access Journals (Sweden)

    Chung-Ho Su

    2013-01-01

    Full Text Available This study presents a hybrid methodology for solving the serious game design evaluation in which evaluation criteria are based on meaningful learning, ARCS motivation, cognitive load, and flow theory (MACF by rough set theory (RST and experts’ selection. The purpose of this study tends to develop an evaluation model with RST based fuzzy Delphi-AHP-TOPSIS for MACF characteristics. Fuzzy Delphi method is utilized for selecting the evaluation criteria, Fuzzy AHP is used for analyzing the criteria structure and determining the evaluation weight of criteria, and Fuzzy TOPSIS is applied to determine the sequence of the evaluations. A real case is also used for evaluating the selection of MACF criteria design for four serious games, and both the practice and evaluation of the case could be explained. The results show that the playfulness (C24, skills (C22, attention (C11, and personalized (C35 are determined as the four most important criteria in the MACF selection process. And evaluation results of case study point out that Game 1 has the best score overall (Game 1 > Game 3 > Game 2 > Game 4. Finally, proposed evaluation framework tends to evaluate the effectiveness and the feasibility of the evaluation model and provide design criteria for relevant multimedia game design educators.

  3. Development of an Evaluation Method for the Design Complexity of Computer-Based Displays

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyoung Ju; Lee, Seung Woo; Kang, Hyun Gook; Seong, Poong Hyun [KAIST, Daejeon (Korea, Republic of); Park, Jin Kyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-10-15

    The importance of the design of human machine interfaces (HMIs) for human performance and the safety of process industries has long been continuously recognized for many decades. Especially, in the case of nuclear power plants (NPPs), HMIs have significant implications for the safety of the NPPs because poor HMIs can impair the decision making ability of human operators. In order to support and increase the decision making ability of human operators, advanced HMIs based on the up-to-date computer technology are provided. Human operators in advanced main control room (MCR) acquire information through video display units (VDUs) and large display panel (LDP), which is required for the operation of NPPs. These computer-based displays contain a huge amount of information and present it with a variety of formats compared to those of a conventional MCR. For example, these displays contain more display elements such as abbreviations, labels, icons, symbols, coding, etc. As computer-based displays contain more information, the complexity of advanced displays becomes greater due to less distinctiveness of each display element. A greater understanding is emerging about the effectiveness of designs of computer-based displays, including how distinctively display elements should be designed. This study covers the early phase in the development of an evaluation method for the design complexity of computer-based displays. To this end, a series of existing studies were reviewed to suggest an appropriate concept that is serviceable to unravel this problem

  4. Designing electronic module based on learning content development system in fostering students’ multi representation skills

    Science.gov (United States)

    Resita, I.; Ertikanto, C.

    2018-05-01

    This study aims to develop electronic module design based on Learning Content Development System (LCDS) to foster students’ multi representation skills in physics subject material. This study uses research and development method to the product design. This study involves 90 students and 6 physics teachers who were randomly chosen from 3 different Senior High Schools in Lampung Province. The data were collected by using questionnaires and analyzed by using quantitative descriptive method. Based on the data, 95% of the students only use one form of representation in solving physics problems. Representation which is tend to be used by students is symbolic representation. Students are considered to understand the concept of physics if they are able to change from one form to the other forms of representation. Product design of LCDS-based electronic module presents text, image, symbolic, video, and animation representation.

  5. Vernacular design based on sustainable disaster's mitigation communication and education strategy

    Science.gov (United States)

    Mansoor, Alvanov Zpalanzani

    2015-04-01

    Indonesia is located between three active tectonic plates, which are prone to natural disasters such as earthquake, volcanic eruption, and also giant tidal wave-tsunami. Adequate infrastructure plays an important role in disaster mitigation, yet without good public awareness, the mitigation process won't be succeeded. The absence of awareness can lead to infrastructure mistreatment. Several reports on lack of understanding or misinterpretation of disaster mitigation especially from rural and coastal communities need to be solved, especially from communication aspects. This is an interdisciplinary study on disaster mitigation communication design and education strategy from visual communication design studies paradigm. This paper depicts research results which applying vernacular design base to elaborate sustainable mitigation communication and education strategy on various visual media and social campaigns. This paper also describes several design approaches which may becomes way to elaborate sustainable awareness and understanding on disaster mitigation among rural and coastal communities in Indonesia.

  6. Research on conflict resolution of collaborative design with fuzzy case-based reasoning method

    Institute of Scientific and Technical Information of China (English)

    HOU Jun-ming; SU Chong; LIANG Shuang; WANG Wan-shan

    2009-01-01

    Collaborative design is a new style for modern mechanical design to meet the requirement of increasing competition. Designers of different places complete the same work, but the conflict appears in the process of design which may interface the design. Case-based reasoning (CBR) method is applied to the problem of conflict resolution, which is in the artificial intelligence field. However, due to the uncertainties in knowledge representation, attribute description, and similarity measures of CBR, it is very difficult to find the similar cases from case database. A fuzzy CBR method was proposed to solve the problem of conflict resolution in collaborative design. The process of fuzzy CBR was introduced. Based on the feature attributes and their relative weights determined by a fuzzy technique, a fuzzy CBR retrieving mechanism was developed to retrieve conflict resolution cases that tend to enhance the functions of the database. By indexing, calculating the weight and defuzzicating of the cases, the case similarity can be obtained. Then the case consistency was measured to keep the right result. Finally, the fuzzy CBR method for conflict resolution was demonstrated by means of a case study. The prototype system based on web is developed to illustrate the methodology.

  7. A Competence-Based Approach to the Design of a Teaching Sequence about Oral and Dental Health and Hygiene: A Case Study

    Science.gov (United States)

    Blanco-López, Ángel; Franco-Mariscal, Antonio Joaquín; España-Ramos, Enrique

    2016-01-01

    We present a case study to illustrate the design and implementation of a teaching sequence about oral and dental health and hygiene. This teaching sequence was aimed at year 10 students (age 15-16) and sought to develop their scientific competences. In line with the PISA assessment framework for science and the tenets of a context-based approach…

  8. Method of software development for tasks of automatic control systems for simulation and designing on the base of the technological systems design data

    International Nuclear Information System (INIS)

    Ajzatulin, A.I.

    2007-01-01

    One studies the factors affecting the designing of the full-scale simulation facilities, the design data base simulation and the application of digital computerized process control systems. Paper describes problems dealing with the errors in the process system design data and the algorithm simulation methodological problems. On the basis of the records of the efforts to design the full-scale simulation facilities of the Tienvan NPP and of the Kudankulam NPP one brings to the notice a procedure to elaborate new tools to simulate and to elaborate algorithms for the computerized process control systems based on the process system design data. Paper lists the basic components of the program system under elaboration to ensure simulation and designing and describes their functions. The introduction result is briefly described [ru

  9. Design of LTCC Based Fractal Antenna

    KAUST Repository

    AdbulGhaffar, Farhan

    2010-09-01

    The thesis presents a Sierpinski Carpet fractal antenna array designed at 24 GHz for automotive radar applications. Miniaturized, high performance and low cost antennas are required for this application. To meet these specifications a fractal array has been designed for the first time on Low Temperature Co-fired Ceramic (LTCC) based substrate. LTCC provides a suitable platform for the development of these antennas due to its properties of vertical stack up and embedded passives. The complete antenna concept involves integration of this fractal antenna array with a Fresnel lens antenna providing a total gain of 15dB which is appropriate for medium range radar applications. The thesis also presents a comparison between the designed fractal antenna and a conventional patch antenna outlining the advantages of fractal antenna over the later one. The fractal antenna has a bandwidth of 1.8 GHz which is 7.5% of the centre frequency (24GHz) as compared to 1.9% of the conventional patch antenna. Furthermore the fractal design exhibits a size reduction of 53% as compared to the patch antenna. In the end a sensitivity analysis is carried out for the fractal antenna design depicting the robustness of the proposed design against the typical LTCC fabrication tolerances.

  10. Effectiveness of design-based learning in engineering education

    NARCIS (Netherlands)

    Gomez Puente, S.M.; Eijck, van M.W.; Jochems, W.M.G.

    2011-01-01

    Design-based learning (DBL) has been introduced as an educational concept at Eindhoven University of Technology (TU/e) in 1997, in which students work co-operatively and actively on multidisciplinary design tasks (Wijnen, 2000). Theoretically DBL is not well underpinned. It has been researched

  11. Designing Dexter-based cooperative hypermedia systems

    DEFF Research Database (Denmark)

    Grønbæk, Kaj; Madsen, Ole Lehrmann; Sloth, Lennard

    1993-01-01

    This paper discusses issues for the design of a Dexter-based cooperative hypermedia architecture and a specific system, DeVise Hypermedia (DHM), developed from this architecture. The Dexter Hypertext Reference Model [Hala90] was used as basis for designing the architecture. The Dexter model...... provides a general and solid foundation for designing a general hypermedia architecture. It introduces central concepts and proposes a layering of the architecture. However, to handle cooperative work aspects, such as sharing material and cooperative authoring, we have to go beyond the Dexter model...... concepts. To deal with such aspects we have extended our implementation of the Dexter concepts with support for long-term transactions, locking and event notification as called for by Halasz [Hala88]. The result is a platform independent architecture for developing cooperative hypermedia systems...

  12. Conceptual Design Studies of the KSTAR Bay-Nm Cassette and Thomson Scattering Optics

    International Nuclear Information System (INIS)

    Feder, R.; Ellis, R.; Johnson, D.; Park, H.; Lee, H.G.

    2005-01-01

    A Multi-Channel Thomson Scattering System viewing the edge and core of the KSTAR plasma will be installed at the mid-plane port Bay-N. An engineering design study was undertaken at PPPL in collaboration with the Korea Basic Science Institute (KBSI) to determine the optimal optics and cassette design. Design criteria included environmental, mechanical and optical factors. All of the optical design options have common design features; the Thomson Scattering laser, an in-vacuum shutter, a quartz heat shield and primary vacuum window, a set of optical elements and a fiber optic bundle. Neutron radiation damage was a major factor in the choice of competing lens-based and mirror-based optical designs. Both the mirror based design and the lens design are constrained by physical limits of the Bay-N cassette and interference with the Bay-N micro-wave launcher. The cassette will contain the optics and a rail system for maintenance of the optics

  13. Design of mechanical coxa joints based on three-degree-of-freedom spherical parallel manipulators

    International Nuclear Information System (INIS)

    Li, Yanbiao; Ji, Shiming; Wang, Zhongfei; Jin, Mingsheng; Liu, Yi; Jin, Zhenlin

    2013-01-01

    We addressed the issue of the design of mechanical coxa joints based on three-degree-of-freedom spherical parallel manipulators using the parameter statistics optimum method based on index atlases. The coxa joints have the advantages of high payload, high accuracy, and good technological efficiency. The first step of the design and prototyping used in this paper develops the direct and inverse displacement equations from the layout feature of the mechanical coxa joints. Then, the shapes of a constant-orientation workspace of the mechanical coxa joints are described, and the effects of the design parameters on the workspace volume are studied quantitatively. The next step deals with the graphical representation of the atlases that illustrates the relationship between performance evaluation index and design parameters based on the kinematics and torque analysis of the mechanical coxa joints. Finally, the geometric parameters of the coxa joints are obtained by the parameter statistics optimum method based on the index atlases. Considering assembly conditions, the design scheme of the mechanical coxa joints is developed, which provides a theoretical basis for the application of the mechanical coxa joints.

  14. Design Students Perspectives on Assessment Rubric in Studio-Based Learning

    Science.gov (United States)

    Eshun, Eric F.; Osei-Poku, Patrick

    2013-01-01

    This study examined students' perspectives on the use of assessment criteria and rubrics in graphic design studio at Kwame Nkrumah University of Science and Technology, Ghana. This assessment strategy was introduced with the desire to improve students' participation and involvement in studio-based learning programme. At the end of the semester, a…

  15. An analysis of teaching competence in science teachers involved in the design of context-based curriculum materials

    NARCIS (Netherlands)

    Putter - Smits, de L.G.A.; Taconis, R.; Driel, van J.H.; Jochems, W.M.G.

    2012-01-01

    The committees for the current Dutch context-based innovation in secondary science education employed teachers to design context-based curriculum materials. A study on the learning of science teachers in design teams for context-based curriculum materials is presented in this paper. In a correlation

  16. Introducing Project-Based Learning to Design Enterprises for Creativity

    DEFF Research Database (Denmark)

    Wang, Feng; Zhou, Chunfang; Chen, Hongbing

    2013-01-01

    This paper aims to emphasize the necessity of introducing Project-Based Learning (PBL) to design enterprises in order to foster designers creativity and facilitate innovation of design enterprises. According to the literature review, creativity can be viewed as the first stage of innovation; PBL...

  17. The applicability of constructivist user studies: how can constructivist inquiry inform service providers and systems designers? Constructivist inquiry, Case study, Systems design, User behaviour

    Directory of Open Access Journals (Sweden)

    Alison Pickard

    2004-01-01

    Full Text Available This paper has attempted to clarify the ways in which individual, holistic case studies, produced via the process of constructivist inquiry, can be tested for trustworthiness and applied to other, similar situations. Service providers and systems designers need contextual information concerning their users in order to design and provide systems and services that will function effectively and efficiently within those contexts. Abstract models can only provide abstract insight into human behaviour and this is rarely sufficient detail upon which to base the planning and delivery of a service. The methodological issues which surround the applicability of individual, holistic case studies are discussed, explaining the concept of 'contextual applicability.' The relevance and usefulness of in-depth case study research to systems designers and service providers is highlighted.

  18. Computer aided fixture design - A case based approach

    Science.gov (United States)

    Tanji, Shekhar; Raiker, Saiesh; Mathew, Arun Tom

    2017-11-01

    Automated fixture design plays important role in process planning and integration of CAD and CAM. An automated fixture setup design system is developed where when fixturing surfaces and points are described allowing modular fixture components to get automatically select for generating fixture units and placed into position with satisfying assembled conditions. In past, various knowledge based system have been developed to implement CAFD in practice. In this paper, to obtain an acceptable automated machining fixture design, a case-based reasoning method with developed retrieval system is proposed. Visual Basic (VB) programming language is used in integrating with SolidWorks API (Application programming interface) module for better retrieval procedure reducing computational time. These properties are incorporated in numerical simulation to determine the best fit for practical use.

  19. Controlled Ecological Life Support Systems (CELSS) conceptual design option study

    Science.gov (United States)

    Oleson, Melvin; Olson, Richard L.

    1986-01-01

    Results are given of a study to explore options for the development of a Controlled Ecological Life Support System (CELSS) for a future Space Station. In addition, study results will benefit the design of other facilities such as the Life Sciences Research Facility, a ground-based CELSS demonstrator, and will be useful in planning longer range missions such as a lunar base or manned Mars mission. The objectives were to develop weight and cost estimates for one CELSS module selected from a set of preliminary plant growth unit (PGU) design options. Eleven Space Station CELSS module conceptual PGU designs were reviewed, components and subsystems identified and a sensitivity analysis performed. Areas where insufficient data is available were identified and divided into the categories of biological research, engineering research, and technology development. Topics which receive significant attention are lighting systems for the PGU, the use of automation within the CELSS system, and electric power requirements. Other areas examined include plant harvesting and processing, crop mix analysis, air circulation and atmosphere contaminant flow subsystems, thermal control considerations, utility routing including accessibility and maintenance, and nutrient subsystem design.

  20. Model-based design of self-Adapting networked signal processing systems

    NARCIS (Netherlands)

    Oliveira Filho, J.A. de; Papp, Z.; Djapic, R.; Oostveen, J.C.

    2013-01-01

    The paper describes a model based approach for architecture design of runtime reconfigurable, large-scale, networked signal processing applications. A graph based modeling formalism is introduced to describe all relevant aspects of the design (functional, concurrency, hardware, communication,

  1. Making the Case for Practice-Based Research and the Imperative Role of Design Practitioners.

    Science.gov (United States)

    Freihoefer, Kara; Zborowsky, Terri

    2017-04-01

    The purpose of this article is to justify the need for evidence-based design (EBD) in a research-based architecture and design practice. This article examines the current state of practice-based research (PBR), supports the need for EBD, illustrates PBR methods that can be applied to design work, and explores how findings can be used as a decision-making tool during design and as a validation tool during postoccupancy. As a result, design professions' body of knowledge will advance and practitioners will be better informed to protect the health, safety, and welfare of the society. Furthermore, characteristics of Friedman's progressive research program are used as a framework to examine the current state of PBR in design practice. A modified EBD approach is proposed and showcased with a case study of a renovated inpatient unit. The modified approach demonstrates how a highly integrated project team, especially the role of design practitioners, contributed to the success of utilizing baseline findings and evidence in decision-making throughout the design process. Lastly, recommendations and resources for learning research concepts are provided for practitioners. It is the role of practitioners to pave the way for the next generation of design professionals, as the request and expectation for research become more prevalent in design practice.

  2. Proposing a New Pedagogy-Based Website Design: A Usability Test with Lifelong Learners

    Science.gov (United States)

    Khlaisang, Jintavee

    2017-01-01

    This study aimed to create a new pedagogy-based website based on the analysis of the needs of 7147 website users who visited the Thailand Cyber University (TCU) project website during 2011-2013. The study consisted of 4 stages: (1) examining learners' needs and literature related to developing a lifelong learning framework, (2) designing a site…

  3. Facilitating Transition to Team Based Design Education

    DEFF Research Database (Denmark)

    Tollestrup, Christian

    2014-01-01

    profession, but at the same time it becomes very difficult to identify where and how the design is created since form-giving now becomes a group effort. So as a way to ease the transition from highly framed and facilitated high school learning context to university self-driven learning context a small...... given to two set of students; one set that received the survival kit in 2011 and 2012 and one set that did not. The questionnaire inquires the students’ attitude towards 4 aspects: 1.General level of preparedness for team and problem based project work 2.Level of information of expectations from...... supervisors and programme 3.Reflection of the role in a team, problem based project work 4.The level of information of special expectations from the Industrial Design program towards team and problem based project work. Results indicates that Class receiving the “Survival Kit” improved in the calibration...

  4. Design Evolution Study - Aging Options

    International Nuclear Information System (INIS)

    McDaniel, P.

    2002-01-01

    The purpose of this study is to identify options and issues for aging commercial spent nuclear fuel received for disposal at the Yucca Mountain Mined Geologic Repository. Some early shipments of commercial spent nuclear fuel to the repository may be received with high-heat-output (younger) fuel assemblies that will need to be managed to meet thermal goals for emplacement. The capability to age as much as 40,000 metric tons of heavy metal of commercial spent nuclear he1 would provide more flexibility in the design to manage this younger fuel and to decouple waste receipt and waste emplacement. The following potential aging location options are evaluated: (1) Surface aging at four locations near the North Portal; (2) Subsurface aging in the permanent emplacement drifts; and (3) Subsurface aging in a new subsurface area. The following aging container options are evaluated: (1) Complete Waste Package; (2) Stainless Steel inner liner of the waste package; (3) Dual Purpose Canisters; (4) Multi-Purpose Canisters; and (5) New disposable canister for uncanistered commercial spent nuclear fuel. Each option is compared to a ''Base Case,'' which is the expected normal waste packaging process without aging. A Value Engineering approach is used to score each option against nine technical criteria and rank the options. Open issues with each of the options and suggested future actions are also presented. Costs for aging containers and aging locations are evaluated separately. Capital costs are developed for direct costs and distributable field costs. To the extent practical, unit costs are presented. Indirect costs, operating costs, and total system life cycle costs will be evaluated outside of this study. Three recommendations for aging commercial spent nuclear fuel--subsurface, surface, and combined surface and subsurface are presented for further review in the overall design re-evaluation effort. Options that were evaluated but not recommended are: subsurface aging in a new

  5. Digital design of scaffold for mandibular defect repair based on tissue engineering.

    Science.gov (United States)

    Liu, Yun-feng; Zhu, Fu-dong; Dong, Xing-tao; Peng, Wei

    2011-09-01

    Mandibular defect occurs more frequently in recent years, and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws. Tissue engineering, which is a hot research field of biomedical engineering, provides a new direction for mandibular defect repair. As the basis and key part of tissue engineering, scaffolds have been widely and deeply studied in regards to the basic theory, as well as the principle of biomaterial, structure, design, and fabrication method. However, little research is targeted at tissue regeneration for clinic repair operations. Since mandibular bone has a special structure, rather than uniform and regular structure in existing studies, a methodology based on tissue engineering is proposed for mandibular defect repair in this paper. Key steps regarding scaffold digital design, such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail. By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping, the feasibility and effectiveness of the proposed methodology are properly verified. More works about mechanical and biological improvements need to be done to promote its clinical application in future.

  6. Digital design of scaffold for mandibular defect repair based on tissue engineering

    Institute of Scientific and Technical Information of China (English)

    Yun-feng LIU; Fu-dong ZHU; Xing-tao DONG; Wei PENG

    2011-01-01

    Mandibular defect occurs more frequently in recent years,and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws.Tissue engineering,which is a hot research field of biomedical engineering,provides a new direction for mandibular defect repair.As the basis and key part of tissue engineering,scaffolds have been widely and deeply studied in regards to the basic theory,as well as the principle of biomaterial,structure,design,and fabrication method.However,little research is targeted at tissue regeneration for clinic repair operations.Since mandibular bone has a special structure,rather than uniform and regular structure in existing studies,a methodology based on tissue engineering is proposed for mandibular defect repair in this paper.Key steps regarding scaffold digital design,such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail.By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping,the feasibility and effectiveness of the proposed methodology are properly verified.More works about mechanical and biological improvements need to be done to promote its clinical application in future.

  7. Analysis of a mammography teaching program based on an affordance design model.

    Science.gov (United States)

    Luo, Ping; Eikman, Edward A; Kealy, William; Qian, Wei

    2006-12-01

    The wide use of computer technology in education, particularly in mammogram reading, asks for e-learning evaluation. The existing media comparative studies, learner attitude evaluations, and performance tests are problematic. Based on an affordance design model, this study examined an existing e-learning program on mammogram reading. The selection criteria include content relatedness, representativeness, e-learning orientation, image quality, program completeness, and accessibility. A case study was conducted to examine the affordance features, functions, and presentations of the selected software. Data collection and analysis methods include interviews, protocol-based document analysis, and usability tests and inspection. Also some statistics were calculated. The examination of PBE identified that this educational software designed and programmed some tools. The learner can use these tools in the process of optimizing displays, scanning images, comparing different projections, marking the region of interests, constructing a descriptive report, assessing one's learning outcomes, and comparing one's decisions with the experts' decisions. Further, PBE provides some resources for the learner to construct one's knowledge and skills, including a categorized image library, a term-searching function, and some teaching links. Besides, users found it easy to navigate and carry out tasks. The users also reacted positively toward PBE's navigation system, instructional aids, layout, pace and flow of information, graphics, and other presentation design. The software provides learners with some cognitive tools, supporting their perceptual problem-solving processes and extending their capabilities. Learners can internalize the mental models in mammogram reading through multiple perceptual triangulations, sensitization of related features, semantic description of mammogram findings, and expert-guided semantic report construction. The design of these cognitive tools and the

  8. The safety designs for the TITAN reversed-field pinch reactor study

    International Nuclear Information System (INIS)

    Wong, C.P.C.; Cheng, E.T.; Creedon, R.L.; Hoot, C.G.; Schultz, K.R.; Grotz, S.P.; Blanchard, J.; Sharafat, S.; Najmabadi, F.

    1989-01-01

    TITAN is a study to investigate the potential of the reversed-field pinch concept as a compact, high-power density energy system. Two reactor concepts were developed, a self-cooled lithium design with vanadium structure and an aqueous solution loop-in-pool design, both operating at 18 MW/m 2 . The key safety features of the TITAN-I lithium-vanadium blanket design are in material selection, fusion power core configuration selection, lithium piping connections, and passive lithium drain tank system. Based on these safety features and results from accident evaluation, TITAN-I can at least be rated at a level 3 of safety assurance. For the TITAN-II aqueous loop-in-pool design, the key passive feature is the complete submersion of the fusion power core and the corresponding primary coolant loop system into a pool of low temperature water. Based on this key safety design feature, the TITAN-II design can be rated at a level 2 of safety assurance. (orig.)

  9. The safety designs for the TITAN reversed-field pinch reactor study

    International Nuclear Information System (INIS)

    Wong, C.P.C.; Cheng, E.T.; Creedon, R.L.; Hoot, C.G.; Schultz, K.R.; Grotz, S.P.; Blanchard, J.P.; Sharafat, S.; Najmabadi, F.

    1988-01-01

    TITAN is a study to investigate the potential of the reversed-field pinch concept as a compact, high-power density energy system. Two reactor concepts were developed, a self-cooled lithium design with vanadium structure and an aqueous solution loop-in-pool design, both operating at 18 MW/m 2 . The key safety features of the TITAN-I lithium-vanadium blanket design are in material selection, fusion power core configuration selection, lithium piping connections and passive lithium drain tank system. Based on these safety features and results from accident evaluation, TITAN-I can at least be rated as level 3 of safety assurance. For the TITAN-II aqueous loop-in-pool design, the key passive feature is the complete submersion of the fusion power core and the corresponding primary coolant loop system into a pool of low temperature water. Based on this key safety design feature, the TITAN-II design can be rated as level 2 of safety assurance. 7 refs., 2 figs

  10. Prediction and evaluation method of wind environment in the early design stage using BIM-based CFD simulation

    International Nuclear Information System (INIS)

    Lee, Sumi; Song, Doosam

    2010-01-01

    Drastic urbanization and manhattanization are causing various problems in wind environment. This study suggests a CFD simulation method to evaluate wind environment in the early design stage of high-rise buildings. The CFD simulation of this study is not a traditional in-depth simulation, but a method to immediately evaluate wind environment for each design alternative and provide guidelines for design modification. Thus, the CFD simulation of this study to evaluate wind environments uses BIM-based CFD tools to utilize building models in the design stage. This study examined previous criteria to evaluate wind environment for pedestrians around buildings and selected evaluation criteria applicable to the CFD simulation method of this study. Furthermore, proper mesh generation method and CPU time were reviewed to find a meaningful CFD simulation result for determining optimal design alternative from the perspective of wind environment in the design stage. In addition, this study is to suggest a wind environment evaluation method through a BIM-based CFD simulation.

  11. A research approach for quality based design of healthy foods: Dried broccoli as a case study

    NARCIS (Netherlands)

    Oliviero, T.; Verkerk, R.; Dekker, M.

    2013-01-01

    An approach for process design based on optimization of product quality attributes is presented. Adsorption drying of broccoli with retention of its health benefits is taken as an example to illustrate the approach. Related to its content of glucosinolates, broccoli has a high potential to reduce

  12. Knowledge representation and knowledge base design for operator advisor system

    International Nuclear Information System (INIS)

    Hangos, K.M.; Sziano, T.; Tapolcai, L.

    1990-01-01

    The problems of knowledge representation, knowledge base handling and design has been described for an Operator Advisor System in the Paks Nuclear Power Plant. The Operator Advisor System is to be implemented as a part of the 5th and 6th unit. The knowledge of the Operator Advisor system is described by a few elementary knowledge items (diagnostic event functions, fault graph, action trees), weighted directed graphs have been found as their common structure. List-type and relational representation of these graphs have been used for the on-line and off-line part of the knowledge base respectively. A uniform data base design and handling has been proposed which consists of a design system, a knowledge base editor and a knowledge base compiler

  13. Process-based organization design and hospital efficiency.

    Science.gov (United States)

    Vera, Antonio; Kuntz, Ludwig

    2007-01-01

    The central idea of process-based organization design is that organizing a firm around core business processes leads to cost reductions and quality improvements. We investigated theoretically and empirically whether the implementation of a process-based organization design is advisable in hospitals. The data came from a database compiled by the Statistical Office of the German federal state of Rheinland-Pfalz and from a written questionnaire, which was sent to the chief executive officers (CEOs) of all 92 hospitals in this federal state. We used data envelopment analysis (DEA) to measure hospital efficiency, and factor analysis and regression analysis to test our hypothesis. Our principal finding is that a high degree of process-based organization has a moderate but significant positive effect on the efficiency of hospitals. The main implication is that hospitals should implement a process-based organization to improve their efficiency. However, to actually achieve positive effects on efficiency, it is of paramount importance to observe some implementation rules, in particular to mobilize physician participation and to create an adequate organizational culture.

  14. A G-function-based reliability-based design methodology applied to a cam roller system

    International Nuclear Information System (INIS)

    Wang, W.; Sui, P.; Wu, Y.T.

    1996-01-01

    Conventional reliability-based design optimization methods treats the reliability function as an ordinary function and applies existing mathematical programming techniques to solve the design problem. As a result, the conventional approach requires nested loops with respect to g-function, and is very time consuming. A new reliability-based design method is proposed in this paper that deals with the g-function directly instead of the reliability function. This approach has the potential of significantly reducing the number of calls for g-function calculations since it requires only one full reliability analysis in a design iteration. A cam roller system in a typical high pressure fuel injection diesel engine is designed using both the proposed and the conventional approach. The proposed method is much more efficient for this application

  15. Model-based system-of-systems engineering for space-based command, control, communication, and information architecture design

    Science.gov (United States)

    Sindiy, Oleg V.

    This dissertation presents a model-based system-of-systems engineering (SoSE) approach as a design philosophy for architecting in system-of-systems (SoS) problems. SoS refers to a special class of systems in which numerous systems with operational and managerial independence interact to generate new capabilities that satisfy societal needs. Design decisions are more complicated in a SoS setting. A revised Process Model for SoSE is presented to support three phases in SoS architecting: defining the scope of the design problem, abstracting key descriptors and their interrelations in a conceptual model, and implementing computer-based simulations for architectural analyses. The Process Model enables improved decision support considering multiple SoS features and develops computational models capable of highlighting configurations of organizational, policy, financial, operational, and/or technical features. Further, processes for verification and validation of SoS models and simulations are also important due to potential impact on critical decision-making and, thus, are addressed. Two research questions frame the research efforts described in this dissertation. The first concerns how the four key sources of SoS complexity---heterogeneity of systems, connectivity structure, multi-layer interactions, and the evolutionary nature---influence the formulation of SoS models and simulations, trade space, and solution performance and structure evaluation metrics. The second question pertains to the implementation of SoSE architecting processes to inform decision-making for a subset of SoS problems concerning the design of information exchange services in space-based operations domain. These questions motivate and guide the dissertation's contributions. A formal methodology for drawing relationships within a multi-dimensional trade space, forming simulation case studies from applications of candidate architecture solutions to a campaign of notional mission use cases, and

  16. Fifth Graders' Learning about Simple Machines through Engineering Design-Based Instruction Using LEGO™ Materials

    Science.gov (United States)

    Marulcu, Ismail; Barnett, Mike

    2013-01-01

    This study is part of a 5-year National Science Foundation-funded project, Transforming Elementary Science Learning Through LEGO™ Engineering Design. In this study, we report on the successes and challenges of implementing an engineering design-based and LEGO™-oriented unit in an urban classroom setting and we focus on the impact of the unit on…

  17. osDesign: An R Package for the Analysis, Evaluation, and Design of Two-Phase and Case-Control Studies

    Directory of Open Access Journals (Sweden)

    Sebastien Haneuse

    2011-08-01

    Full Text Available The two-phase design has recently received attention in the statistical literature as an extension to the traditional case-control study for settings where a predictor of interest is rare or subject to missclassification. Despite a thorough methodological treatment and the potential for substantial efficiency gains, the two-phase design has not been widely adopted. This may be due, in part, to a lack of general-purpose, readily-available software. The osDesign package for R provides a suite of functions for analyzing data from a two-phase and/or case-control design, as well as evaluating operating characteristics, including bias, efficiency and power. The evaluation is simulation-based, permitting flexible application of the package to a broad range of scientific settings. Using lung cancer mortality data from Ohio, the package is illustrated with a detailed case-study in which two statistical goals are considered: (i the evaluation of small-sample operating characteristics for two-phase and case-control designs and (ii the planning and design of a future two-phase study.

  18. Employee knowledge of value-based insurance design benefits.

    Science.gov (United States)

    Henrikson, Nora B; Anderson, Melissa L; Hubbard, Rebecca A; Fishman, Paul; Grossman, David C

    2014-08-01

    Value-based insurance designs (VBD) incorporate evidence-based medicine into health benefit design. Consumer knowledge of new VBD benefits is important to assessing their impact on health care use. To assess knowledge of features of a VBD. The eligible study population was employees receiving healthcare benefits in an integrated care system in the U.S. Pacific Northwest. In 2010, participants completed a web-based survey 2 months after rollout of the plan, including three true/false questions about benefit design features including copays for preventive care visits and chronic disease medications and premium costs. Analysis was completed in 2012. Knowledgeable was defined as correct response to all three questions; self-reported knowledge was also assessed. A total of 3,463 people completed the survey (response rate=71.7%). The majority of respondents were female (80.1%) Caucasians (79.6%) aged 35-64 years (79.0%), reflecting the overall employee population. A total of 45.7% had at least a 4-year college education, and 69.1% were married. About three quarters of respondents correctly answered each individual question; half (52.1%) of respondents answered all three questions correctly. On multivariate analysis, knowledge was independently associated with female gender (OR=1.80, 95% CI=1.40, 2.31); Caucasian race (OR=1.72, 95% CI=1.28, 2.32); increasing household income (OR for ≥$100,000=1.86, 95% CI=1.29, 2.68); nonunion job status (OR compared to union status=1.63, 95% CI=1.17, 2.26); and high satisfaction with the health plan (OR compared to low satisfaction=1.26; 95% CI=1.00, 1.57). Incomplete knowledge of benefits is prevalent in an employee population soon after VBD rollout. Copyright © 2014 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

  19. A Web-Based Adaptive Tutor to Teach PCR Primer Design

    Science.gov (United States)

    van Seters, Janneke R.; Wellink, Joan; Tramper, Johannes; Goedhart, Martin J.; Ossevoort, Miriam A.

    2012-01-01

    When students have varying prior knowledge, personalized instruction is desirable. One way to personalize instruction is by using adaptive e-learning to offer training of varying complexity. In this study, we developed a web-based adaptive tutor to teach PCR primer design: the PCR Tutor. We used part of the Taxonomy of Educational Objectives (the…

  20. Anthropometric data base for power plant design. Special report

    International Nuclear Information System (INIS)

    Parris, H.L.

    1981-07-01

    The primary study objective is to develop anthropometric data based upon the men and women who operate and maintain nuclear power plants. Age, stature, and weight information were obtained by a questionnaire survey of current operator and maintenance personnel, and the data extracted from the questionnaires were analyzed to derive body-size information for a number of anthropometric variables of interest to designers. Body-size information was developed separately for both men and women. Results achieved for the male population can be utilized by designers with a high level of confidence for the design of general workplaces. While the number of women respondents in the sample proved to be too small to derive results to which a similarly high level of reliability could be attached, the data can nevertheless be used as reasonable indicators of the probable body-size variability to be found among female power plant employees

  1. An investigation of the effects of relevant samples and a comparison of verification versus discovery based lab design

    Science.gov (United States)

    Rieben, James C., Jr.

    This study focuses on the effects of relevance and lab design on student learning within the chemistry laboratory environment. A general chemistry conductivity of solutions experiment and an upper level organic chemistry cellulose regeneration experiment were employed. In the conductivity experiment, the two main variables studied were the effect of relevant (or "real world") samples on student learning and a verification-based lab design versus a discovery-based lab design. With the cellulose regeneration experiment, the effect of a discovery-based lab design vs. a verification-based lab design was the sole focus. Evaluation surveys consisting of six questions were used at three different times to assess student knowledge of experimental concepts. In the general chemistry laboratory portion of this study, four experimental variants were employed to investigate the effect of relevance and lab design on student learning. These variants consisted of a traditional (or verification) lab design, a traditional lab design using "real world" samples, a new lab design employing real world samples/situations using unknown samples, and the new lab design using real world samples/situations that were known to the student. Data used in this analysis were collected during the Fall 08, Winter 09, and Fall 09 terms. For the second part of this study a cellulose regeneration experiment was employed to investigate the effects of lab design. A demonstration creating regenerated cellulose "rayon" was modified and converted to an efficient and low-waste experiment. In the first variant students tested their products and verified a list of physical properties. In the second variant, students filled in a blank physical property chart with their own experimental results for the physical properties. Results from the conductivity experiment show significant student learning of the effects of concentration on conductivity and how to use conductivity to differentiate solution types with the

  2. A systematic composite service design modeling method using graph-based theory.

    Science.gov (United States)

    Elhag, Arafat Abdulgader Mohammed; Mohamad, Radziah; Aziz, Muhammad Waqar; Zeshan, Furkh

    2015-01-01

    The composite service design modeling is an essential process of the service-oriented software development life cycle, where the candidate services, composite services, operations and their dependencies are required to be identified and specified before their design. However, a systematic service-oriented design modeling method for composite services is still in its infancy as most of the existing approaches provide the modeling of atomic services only. For these reasons, a new method (ComSDM) is proposed in this work for modeling the concept of service-oriented design to increase the reusability and decrease the complexity of system while keeping the service composition considerations in mind. Furthermore, the ComSDM method provides the mathematical representation of the components of service-oriented design using the graph-based theoryto facilitate the design quality measurement. To demonstrate that the ComSDM method is also suitable for composite service design modeling of distributed embedded real-time systems along with enterprise software development, it is implemented in the case study of a smart home. The results of the case study not only check the applicability of ComSDM, but can also be used to validate the complexity and reusability of ComSDM. This also guides the future research towards the design quality measurement such as using the ComSDM method to measure the quality of composite service design in service-oriented software system.

  3. Reference task-based design of crisis management games

    NARCIS (Netherlands)

    Link, Daniel; Meesters, Kenny; Hellingrath, Bernd; van de Walle, B.A.; Hiltz, S.R.; Pfaff, M.S.; Plotnick, L.; Shih, P.C.

    Serious games are an effective tool for giving players a hands-on, immersive experience of crisis situations. To simplify the design of such games while ensuring their relevance, we propose a design method that is based on reference tasks. The feasibility of this approach is demonstrated by the

  4. Generation of TALE-Based Designer Epigenome Modifiers.

    Science.gov (United States)

    Nitsch, Sandra; Mussolino, Claudio

    2018-01-01

    Manipulation of gene expression can be facilitated by editing the genome or the epigenome. Precise genome editing is traditionally achieved by using designer nucleases which are generally exploited to eliminate a specific gene product. Upon the introduction of a site-specific DNA double-strand break (DSB) by the nuclease, endogenous DSB repair mechanisms are in turn harnessed to induce DNA sequence changes that can result in target gene inactivation. Minimal off-target effects can be obtained by endowing designer nucleases with the highly specific DNA-binding domain (DBD) derived from transcription activator-like effectors (TALEs). In contrast, epigenome editing allows gene expression control without inducing changes in the DNA sequence by specifically altering epigenetic marks, as histone tails modifications or DNA methylation patterns within promoter or enhancer regions. Importantly, this approach allows both up- and downregulation of the target gene expression, and the effect is generally reversible. TALE-based designer epigenome modifiers combine the high specificity of TALE-derived DBDs with the power of epigenetic modifier domains to induce fast and long-lasting changes in the epigenetic landscape of a target gene and control its expression. Here we provide a detailed description for the generation of TALE-based designer epigenome modifiers and of a suitable reporter cell line to easily monitor their activity.

  5. Design spectrums based on earthquakes recorded at tarbela

    International Nuclear Information System (INIS)

    Rizwan, M.; Ilyas, M.; Masood, A.

    2008-01-01

    First Seismological Network in Pakistan was setup in early 1969 at Tarbela, which is the location of largest water reservoir of the country. The network consisted of Analog Accelerograms and Seismographs. Since the installation many seismic events of different magnitudes occurred and were recorded by the installed instruments. The analog form of recorded time histories has been digitized and data of twelve earthquakes, irrespective of the type of soil, has been used to derive elastic design spectrums for Tarbela, Pakistan. The PGA scaling factors, based on the risk analysis studies carried out for the region, for each component are also given. The design spectrums suggested will be very useful for carrying out new construction in the region and its surroundings. The digitized data of time histories will be useful for seismic response analysis of structures and seismic risk analysis of the region. (author)

  6. Development of small, fast reactor core designs using lead-based coolant

    International Nuclear Information System (INIS)

    Cahalan, J. E.; Hill, R. N.; Khalil, H. S.; Wade, D. C.

    1999-01-01

    A variety of small (100 MWe) fast reactor core designs are developed, these include compact configurations, long-lived (15-year fuel lifetime) cores, and derated, natural circulation designs. Trade studies are described which identify key core design issues for lead-based coolant systems. Performance parameters and reactivity feedback coefficients are compared for lead-bismuth eutectic (LBE) and sodium-cooled cores of consistent design. The results of these studies indicate that the superior neutron reflection capability of lead alloys reduces the enrichment and burnup swing compared to conventional sodium-cooled systems; however, the discharge fluence is significantly increased. The size requirement for long-lived systems is constrained by reactivity loss considerations, not fuel burnup or fluence limits. The derated lead-alloy cooled natural circulation cores require a core volume roughly eight times greater than conventional compact systems. In general, reactivity coefficients important for passive safety performance are less favorable for the larger, derated configurations

  7. A multinational clinical approach to assessing the effectiveness of catheter-based ultrasound renal denervation: The RADIANCE-HTN and REQUIRE clinical study designs.

    Science.gov (United States)

    Mauri, Laura; Kario, Kazuomi; Basile, Jan; Daemen, Joost; Davies, Justin; Kirtane, Ajay J; Mahfoud, Felix; Schmieder, Roland E; Weber, Michael; Nanto, Shinsuke; Azizi, Michel

    2018-01-01

    Catheter-based renal denervation is a new approach to treat hypertension via modulation of the renal sympathetic nerves. Although nonrandomized and small, open-label randomized studies resulted in significant reductions in office blood pressure 6months after renal denervation with monopolar radiofrequency catheters, the first prospective, randomized, sham-controlled study (Symplicity HTN-3) failed to meet its blood pressure efficacy end point. New clinical trials with new catheters have since been designed to address the limitations of earlier studies. Accordingly, the RADIANCE-HTN and REQUIRE studies are multicenter, blinded, randomized, sham-controlled trials designed to assess the blood pressure-lowering efficacy of the ultrasound-based renal denervation system (Paradise) in patients with established hypertension either on or off antihypertensive medications, is designed to evaluate patients in 2 cohorts-SOLO and TRIO, in the United States and Europe. The SOLO cohort includes patients with essential hypertension, at low cardiovascular risk, and either controlled on 1 to 2 antihypertensive medications or uncontrolled on 0 to 2 antihypertensive medications. Patients undergo a 4-week medication washout period before randomization to renal denervation (treatment) or renal angiogram (sham). The TRIO cohort includes patients with hypertension resistant to at least 3 antihypertensive drugs including a diuretic. Patients will be stabilized on a single-pill, triple-antihypertensive-drug combination for 4weeks before randomization to treatment or sham. Reduction in daytime ambulatory systolic blood pressure (primary end point) will be assessed at 2months in both cohorts. A predefined medication escalation protocol, as needed for blood pressure control, is implemented between 2 and 6months in both cohorts by a study staff member blinded to the randomization process. At 6months, daytime ambulatory blood pressure and antihypertensive treatment score will be assessed. REQUIRE

  8. User Preferences for Web-Based Module Design Layout and Design Impact on Information Recall Considering Age

    Science.gov (United States)

    Pomales-García, Cristina; Rivera-Nivar, Mericia

    2015-01-01

    Research in design of Web-based modules should incorporate aging as an important factor given the diversity of the current workforce. This work aims to understand how Web-Based Learning modules can be designed to accommodate young (25-35 years) as well as older (55-65 years) users by: (1) identifying how information sources (instructor video,…

  9. Study on advanced structural design for commercialized fast breeder reactors

    International Nuclear Information System (INIS)

    Morishita, Masaki; Aoto, Kazumi; Kasahara, Naoto; Asayama, Tai

    2003-05-01

    Japan Nuclear Cycle Development Institute (JNC) and Japan Atomic Power Company (JAPC) launched joint research programs on structural design and three-dimensional seismic isolation technologies, as part of the supporting R and D activities for the feasibility studies on commercialized fast breeder reactor cycle systems. A research project by JAPC under the auspices of the Ministry of Economy, Trade, and Industry (METI) with technical support by JNC is included in this joint study. This report contains the results of the research on the structural design technology. The research scope was identified as (1) FDS (FBR Design Standard), (2) Standardization of new material, and (3) System Based Code for Integrity, and the results of this year's studies are summarized as follows. (1) FDS (FBR Design Standard). R and D policy of Phase II study considering to the newest needs demanded for structural design were clarified, and R and D items were settled concretely. As for failure criteria, preliminary ratcheting-fatigue tests were conducted with rational methods, and Negligible Creep curves that settle creep designing region rationally were expanded their applying condition. R and D policy and items of guideline for inelastic analysis were clarified, and analyzing methodologies were studied. Summering up exemplification of thermal load prediction methodologies were progressed. To predict thermal striping loads, advanced frequency response function of thermal stress, and fatigue evaluation methodology were studied. (2) Standardization of new material. As for candidate 12-chromium stainless steel (added tungsten, non-added tungsten), that is expected to improve strength of components of commercialized FR, short and medium-term material tests, and creep-fatigue tests at small strain range were conducted. As for above candidate steel, TIG (Tungsten Inert Gas) welding method was recommended. Requirements to standardize new materials and index to select new materials were studied

  10. Design of structurally colored surfaces based on scalar diffraction theory

    DEFF Research Database (Denmark)

    Johansen, Villads Egede; Andkjær, Jacob Anders; Sigmund, Ole

    2014-01-01

    In this paper we investigate the possibility of controlling the color and appearance of surfaces simply by modifying the height profile of the surface on a nanoscale level. The applications for such methods are numerous: new design possibilities for high-end products, color engraving on any highly...... reflective surface, paint-free text and coloration, UV-resistant coloring, etc. In this initial study, the main focus is on finding a systematic way to obtain these results. For now the simulation and optimization is based on a simple scalar diffraction theory model. From the results, several design issues...

  11. Aggregation Operator Based Fuzzy Pattern Classifier Design

    DEFF Research Database (Denmark)

    Mönks, Uwe; Larsen, Henrik Legind; Lohweg, Volker

    2009-01-01

    This paper presents a novel modular fuzzy pattern classifier design framework for intelligent automation systems, developed on the base of the established Modified Fuzzy Pattern Classifier (MFPC) and allows designing novel classifier models which are hardware-efficiently implementable....... The performances of novel classifiers using substitutes of MFPC's geometric mean aggregator are benchmarked in the scope of an image processing application against the MFPC to reveal classification improvement potentials for obtaining higher classification rates....

  12. Product design pattern based on big data-driven scenario

    OpenAIRE

    Conggang Yu; Lusha Zhu

    2016-01-01

    This article discusses about new product design patterns in the big data era, gives designer a new rational thinking way, and is a new way to understand the design of the product. Based on the key criteria of the product design process, category, element, and product are used to input the data, which comprises concrete data and abstract data as an enlargement of the criteria of product design process for the establishment of a big data-driven product design pattern’s model. Moreover, an exper...

  13. Spatio-temporal model based optimization framework to design future hydrogen infrastructure networks

    International Nuclear Information System (INIS)

    Konda, N.V.S.; Shah, N.; Brandon, N.P.

    2009-01-01

    A mixed integer programming (MIP) spatio-temporal model was used to design hydrogen infrastructure networks for the Netherlands. The detailed economic analysis was conducted using a multi-echelon model of the entire hydrogen supply chain, including feed, production, storage, and transmission-distribution systems. The study considered various near-future and commercially available technologies. A multi-period model was used to design evolutionary hydrogen supply networks in coherence with growing demand. A scenario-based analysis was conducted in order to account for uncertainties in future demand. The study showed that competitive hydrogen networks can be designed for any conceivable scenario. It was concluded that the multi-period model presented significant advantages in relation to decision-making over long time-horizons

  14. Model-based design and optimization of vanadium redox flow batteries

    Energy Technology Data Exchange (ETDEWEB)

    Koenig, Sebastian

    2017-07-19

    This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm{sup 2} and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

  15. Model-based design and optimization of vanadium redox flow batteries

    International Nuclear Information System (INIS)

    Koenig, Sebastian

    2017-01-01

    This work targets on increasing the efficiency of the Vanadium Redox Flow Battery (VRFB) using a model-based approach. First, a detailed instruction for setting up a VRFB model on a system level is given. Modelling of open-circuit-voltage, ohmic overpotential, concentration overpotential, Vanadium crossover, shunt currents as well as pump power demand is presented. All sub-models are illustrated using numerical examples. Using experimental data from three battery manufacturers, the voltage model validated. The identified deviations reveal deficiencies in the literature model. By correctly deriving the mass transfer coefficients and adapting the effective electrode area, these deficiencies are eliminated. The validated battery model is then deployed in an extensive design study. By varying the electrode area between 1000 and 4000 cm 2 and varying the design of the electrolyte supply channel, twenty-four different cell designs are created using finite element analysis. These designs are subsequently simulated in 40-cell stacks deployed in systems with a single stack and systems with a three-stack string. Using the simulation results, the impact of different design parameters on different loss mechanisms is investigated. While operating the VRFB, the electrolyte flow rate is the most important operational parameter. A novel, model-based optimization strategy is presented and compared to established flow rate control strategies. Further, a voltage controller is introduced which delays the violation of cell voltage limits by controlling the flow rate as long as the pump capacity is not fully exploited.

  16. Value-based insurance design: benefits beyond cost and utilization.

    Science.gov (United States)

    Gibson, Teresa B; Maclean, Ross J; Chernew, Michael E; Fendrick, A Mark; Baigel, Colin

    2015-01-01

    As value-based insurance design (VBID) programs proliferate, evidence is emerging on the impact of VBID. To date, studies have largely measured VBID impact on utilization, and a few studies have assessed its impact on quality, outcomes, and cost. In this commentary we discuss these domains, summarize evidence, and propose the extension of measurement of VBID impact into areas including workplace productivity and quality of life, employee and patient engagement, and talent attraction and retention. We contend that VBID evaluations should consider a broad variety of programmatic dividends on both humanistic and health-related outcomes.

  17. Integrated layout based Monte-Carlo simulation for design arc optimization

    Science.gov (United States)

    Shao, Dongbing; Clevenger, Larry; Zhuang, Lei; Liebmann, Lars; Wong, Robert; Culp, James

    2016-03-01

    Design rules are created considering a wafer fail mechanism with the relevant design levels under various design cases, and the values are set to cover the worst scenario. Because of the simplification and generalization, design rule hinders, rather than helps, dense device scaling. As an example, SRAM designs always need extensive ground rule waivers. Furthermore, dense design also often involves "design arc", a collection of design rules, the sum of which equals critical pitch defined by technology. In design arc, a single rule change can lead to chain reaction of other rule violations. In this talk we present a methodology using Layout Based Monte-Carlo Simulation (LBMCS) with integrated multiple ground rule checks. We apply this methodology on SRAM word line contact, and the result is a layout that has balanced wafer fail risks based on Process Assumptions (PAs). This work was performed at the IBM Microelectronics Div, Semiconductor Research and Development Center, Hopewell Junction, NY 12533

  18. The Development of a Robot-Based Learning Companion: A User-Centered Design Approach

    Science.gov (United States)

    Hsieh, Yi-Zeng; Su, Mu-Chun; Chen, Sherry Y.; Chen, Gow-Dong

    2015-01-01

    A computer-vision-based method is widely employed to support the development of a variety of applications. In this vein, this study uses a computer-vision-based method to develop a playful learning system, which is a robot-based learning companion named RobotTell. Unlike existing playful learning systems, a user-centered design (UCD) approach is…

  19. Projecting the Future for Design Science Research: An Action‐Case Based Analysis

    DEFF Research Database (Denmark)

    Baskerville, Richard; Pries-Heje, Jan

    2015-01-01

    and theories appears to be a key challenge. In this paper we commence with a DESRIST paper from 2012 that instantiated design principles in an artifact for a bank. That paper included plans and techniques for future use of its principles (propagation), including prescriptions for a five-phase adoption process...... or theories have stimulated many actual projections. We demonstrate these concepts in a case study of propagation: a chemical manufacturer and service provider that adopted the design principles arising from that 2012 DESRIST banking-based design science research. We conclude that generalizability is too well...

  20. Brugervenligt design: Design af applikation med fokus på usability og lokationsbaseret marketing: Usability Design: App-design with a focus on usability and Location Based Advertising

    OpenAIRE

    Pape, Nicklas Skov; Kofoed, Rune Weise; Jørgensen, Rasmus Christian

    2014-01-01

    The present project is based on an assumed demand for less visual pollution in the public domain, which is facilitated by alternative design and the use of location based technology, rather than radical legislation in the form of prohibitions or restrictions. Through the use of innovative techniques of creative concept development and iterative prototyping, the goal of this project is to design a prototype of a user friendly smartphone application on the basis of location-based and targeted m...

  1. Data base systems in electronic design engineering

    Science.gov (United States)

    Williams, D.

    1980-01-01

    The concepts of an integrated design data base system (DBMS) as it might apply to an electronic design company are discussed. Data elements of documentation, project specifications, project tracking, firmware, software, electronic and mechanical design can be integrated and managed through a single DBMS. Combining the attributes of a DBMS data handler with specialized systems and functional data can provide users with maximum flexibility, reduced redundancy, and increased overall systems performance. Although some system overhead is lost due to redundancy in transitory data, it is believed the combination of the two data types is advisable rather than trying to do all data handling through a single DBMS.

  2. A constraint-based approach to intelligent support of nuclear reactor design

    International Nuclear Information System (INIS)

    Furuta, Kazuo

    1993-01-01

    Constraint is a powerful representation to formulate and solve problems in design; a constraint-based approach to intelligent support of nuclear reactor design is proposed. We first discuss the features of the approach, and then present the architecture of a nuclear reactor design support system under development. In this design support system, the knowledge base contains constraints useful to structure the design space as object class definitions, and several types of constraint resolvers are provided as design support subsystems. The adopted method of constraint resolution are explained in detail. The usefulness of the approach is demonstrated using two design problems: Design window search and multiobjective optimization in nuclear reactor design. (orig./HP)

  3. Design of Pd-Based Bimetallic Catalysts for ORR: A DFT Calculation Study

    Directory of Open Access Journals (Sweden)

    Lihui Ou

    2015-01-01

    Full Text Available Developing Pd-lean catalysts for oxygen reduction reaction (ORR is the key for large-scale application of proton exchange membrane fuel cells (PEMFCs. In the present paper, we have proposed a multiple-descriptor strategy for designing efficient and durable ORR Pd-based alloy catalysts. We demonstrated that an ideal Pd-based bimetallic alloy catalyst for ORR should possess simultaneously negative alloy formation energy, negative surface segregation energy of Pd, and a lower oxygen binding ability than pure Pt. By performing detailed DFT calculations on the thermodynamics, surface chemistry and electronic properties of Pd-M alloys, Pd-V, Pd-Fe, Pd-Zn, Pd-Nb, and Pd-Ta, are identified theoretically to have stable Pd segregated surface and improved ORR activity. Factors affecting these properties are analyzed. The alloy formation energy of Pd with transition metals M can be mainly determined by their electron interaction. This may be the origin of the negative alloy formation energy for Pd-M alloys. The surface segregation energy of Pd is primarily determined by the surface energy and the atomic radius of M. The metals M which have smaller atomic radius and higher surface energy would tend to favor the surface segregation of Pd in corresponding Pd-M alloys.

  4. Compositional gossip: a conceptual architecture for designing gossip-based applications

    OpenAIRE

    Rivière, Étienne; Baldoni, Roberto; Li, Harry; Pereira, José

    2007-01-01

    Most proposed gossip-based systems use an ad-hoc design. We observe a low degree of reutilization among this proposals. We present how this limits both the systematic development of gossip-based applications and the number of applications that can benefit from gossip-based construction. We posit that these reinvent-the-wheel approaches poses a significant barrier to the spread and usability of gossip protocols. This paper advocates a conceptual design framework based upon aggregating basic an...

  5. Design factors and considerations for a time-based flight management system

    Science.gov (United States)

    Vicroy, D. D.; Williams, D. H.; Sorensen, J. A.

    1986-01-01

    Recent NASA Langley Research Center research to develop a technology data base from which an advanced Flight Management System (FMS) design might evolve is reviewed. In particular, the generation of fixed range cruise/descent reference trajectories which meet predefined end conditions of altitude, speed, and time is addressed. Results on the design and theoretical basis of the trajectory generation algorithm are presented, followed by a brief discussion of a series of studies that are being conducted to determine the accuracy requirements of the aircraft and weather models resident in the trajectory generation algorithm. Finally, studies to investigate the interface requirements between the pilot and an advanced FMS are considered.

  6. Design and manufacturing of bio-based sandwich structures

    CSIR Research Space (South Africa)

    John, Maya J

    2017-03-01

    Full Text Available The aim of this chapter is to discuss the design and manufacturing of bio-based sandwich structures. As the economic advantages of weight reduction have become mandatory for many advanced industries, bio-based sandwich panels have emerged...

  7. Analyzing Reliability and Performance Trade-Offs of HLS-Based Designs in SRAM-Based FPGAs Under Soft Errors

    Science.gov (United States)

    Tambara, Lucas Antunes; Tonfat, Jorge; Santos, André; Kastensmidt, Fernanda Lima; Medina, Nilberto H.; Added, Nemitala; Aguiar, Vitor A. P.; Aguirre, Fernando; Silveira, Marcilei A. G.

    2017-02-01

    The increasing system complexity of FPGA-based hardware designs and shortening of time-to-market have motivated the adoption of new designing methodologies focused on addressing the current need for high-performance circuits. High-Level Synthesis (HLS) tools can generate Register Transfer Level (RTL) designs from high-level software programming languages. These tools have evolved significantly in recent years, providing optimized RTL designs, which can serve the needs of safety-critical applications that require both high performance and high reliability levels. However, a reliability evaluation of HLS-based designs under soft errors has not yet been presented. In this work, the trade-offs of different HLS-based designs in terms of reliability, resource utilization, and performance are investigated by analyzing their behavior under soft errors and comparing them to a standard processor-based implementation in an SRAM-based FPGA. Results obtained from fault injection campaigns and radiation experiments show that it is possible to increase the performance of a processor-based system up to 5,000 times by changing its architecture with a small impact in the cross section (increasing up to 8 times), and still increasing the Mean Workload Between Failures (MWBF) of the system.

  8. Model-based design of supervisory controllers for baggage handling systems

    NARCIS (Netherlands)

    Swartjes, L.; van Beek, D.A.; Fokkink, W.J.; van Eekelen, J.A.W.M.

    2017-01-01

    The complexity of airport baggage handling systems in combination with the required high level of robustness makes designing supervisory controllers for these systems a challenging task. We show how a state of the art, formal, model-based design framework has been successfully used for model-based

  9. Issues in Text Design and Layout for Computer Based Communications.

    Science.gov (United States)

    Andresen, Lee W.

    1991-01-01

    Discussion of computer-based communications (CBC) focuses on issues involved with screen design and layout for electronic text, based on experiences with electronic messaging, conferencing, and publishing within the Australian Open Learning Information Network (AOLIN). Recommendations for research on design and layout for printed text are also…

  10. Secure image encryption algorithm design using a novel chaos based S-Box

    International Nuclear Information System (INIS)

    Çavuşoğlu, Ünal; Kaçar, Sezgin; Pehlivan, Ihsan; Zengin, Ahmet

    2017-01-01

    Highlights: • A new chaotic system is developed for creating S-Box and image encryption algorithm. • Chaos based random number generator is designed with the help of the new chaotic system. NIST tests are run on generated random numbers to verify randomness. • A new S-Box design algorithm is developed to create the chaos based S-Box to be utilized in encryption algorithm and performance tests are made. • The new developed S-Box based image encryption algorithm is introduced and image encryption application is carried out. • To show the quality and strong of the encryption process, security analysis are performed and compared with the AES and chaos algorithms. - Abstract: In this study, an encryption algorithm that uses chaos based S-BOX is developed for secure and speed image encryption. First of all, a new chaotic system is developed for creating S-Box and image encryption algorithm. Chaos based random number generator is designed with the help of the new chaotic system. Then, NIST tests are run on generated random numbers to verify randomness. A new S-Box design algorithm is developed to create the chaos based S-Box to be utilized in encryption algorithm and performance tests are made. As the next step, the new developed S-Box based image encryption algorithm is introduced in detail. Finally, image encryption application is carried out. To show the quality and strong of the encryption process, security analysis are performed. Proposed algorithm is compared with the AES and chaos algorithms. According to tests results, the proposed image encryption algorithm is secure and speed for image encryption application.

  11. Conceptual design study of fusion experimental reactor (FY86 FER)

    International Nuclear Information System (INIS)

    Saito, Ryusei; Kashihara, Shin-ichiro; Itoh, Shin-ichi

    1987-08-01

    This report describes the results of conceptual design study on plant systems for the Fusion Experimental Reactor (FY86 FER). Design studies for FER plant systems have been continued from FY85, especially for design modifications made in accordance with revisions of plasma scaling parameters and system improvements. This report describes 1) system construction, 2) site and reactor building plan, 3) repaire and maintenance system, 4) tritium circulation system, 5) heating, ventilation and air conditioning system, 6) tritium clean-up system, 7) cooling and baking system, 8) waste treatment and storage system, 9) control system, 10) electric power system, 11) site factory plan, all of which are a part of FY86 design work. The plant systems described in this report generally have been based on the FY86 FER (ACS Reactor) which is an one of the six candidates for FER. (author)

  12. ELMO Bumpy Torus Reactor and power plant: conceptual design study

    International Nuclear Information System (INIS)

    Bathke, C.G.; Dudziak, D.J.; Krakowski, R.A.

    1981-08-01

    A complete power plant design of a 1200-MWe ELMO Bumpy Torus Reactor (EBTR) is presented. An emphasis is placed on those features that are unique to the EBT confinement concept, with subsystems and balance-of-plant items that are more generic to magnetic fusion being adapted from past, more extensive tokamak reactor designs. Similar to the latter tokamak studies, this conceptual EBTR design also emphasizes the use of conventional or near state-of-the-art engineering technology and materials. An emphasis is also placed on system accessibility, reliability, and maintainability, as these crucial and desirable characteristics relate to the unique high-aspect-ratio configuration of EBTs. Equal and strong emphasis is given to physics, engineering/technology, and costing/economics components of this design effort. Parametric optimizations and sensitivity studies, using cost-of-electricity as an object function, are reported. Based on these results, the direction for future improvement on an already attractive reactor design is identified

  13. Implementation of knowledge-based palliative care in nursing homes and pre-post post evaluation by cross-over design: a study protocol.

    Science.gov (United States)

    Ahlström, Gerd; Nilsen, Per; Benzein, Eva; Behm, Lina; Wallerstedt, Birgitta; Persson, Magnus; Sandgren, Anna

    2018-03-22

    The demography of the world is changing as the population is ageing. Because of this change to a higher proportion of older people, the WHO has called for improved palliative care for older persons. A large number of all deaths in the industrialised world occur while older people are living in nursing homes and therefore a key question becomes how the principles of palliative care can be implemented in that context. The aims of this study are: a) to describe a model of an educational intervention with the goal of implementing knowledge-based palliative care in nursing homes, and b) to describe the design of the evaluation of the effectiveness regarding the implementation of knowledge-based palliative care. A complex intervention is evaluated by means of a cross-over design. An educational intervention concerning palliative care consisting of five seminars during 6 months for staff and managers has been developed and conducted in 20 nursing homes in two counties. Before the intervention started, the feasibility was tested in a pilot study conducted in nursing homes not included in the main study. The intervention is evaluated through a non-randomized experimental design with intervention and control groups and pre- and post-assessments. The evaluation includes older persons living in nursing homes, next-of-kin, staff and managers. Data collection consists of quantitative methods such as questionnaires and register data and qualitative methods in the form of individual interviews, focus-group interviews and participant observations. The research will contribute to new knowledge about how to implement knowledge-based palliative care in a nursing home setting. A strength of this project is that the Medical Research Council framework of complex intervention is applied. The four recommended stages, Development, Feasibility and piloting, Evaluation and Implementation, are combined for the educational intervention, which functions as a strategy to achieve knowledge-based

  14. Preliminary design study of pebble bed reactor HTR-PM base using once-through-then-out fuel recirculation

    International Nuclear Information System (INIS)

    Topan Setiadipura; Jupiter S Pane; Zuhair

    2016-01-01

    Pebble Bed Reactor (PBR) is one of the advanced reactor type implementing strong passive safety feature. In this type of design has the potential to do a cogeneration useful for the treatment of various minerals in various islands in Indonesia. The operation of the PBR can be simplified by implementing once-through-then-out (OTTO) fuel recirculation scheme in which pebble fuel only pass the core once time. The purpose of this research is to understand quantitative influence of the changing of fuel element recirculation on the PBR core performance and to find preliminary optimization design of PBR type reactor with OTTO recirculation scheme. PEBBED software was used to find PBR equilibrium core. The calculation result gives quantitative data on the impact of implementing a different fuel recirculation, especially using OTTO scheme. Furthermore, an early optimized PBR design based on HTR-PM using OTTO scheme was obtained where the power must be downgraded into 115 MWt in order to preserve the safety feature. The simplicity of the reactor operation and the reduction of reactor component with OTTO scheme still make this early optimized design an interesting alternative design, despite its power reduction from the reference design. (author)

  15. Preliminary neutronics design studies for a 400 MWt STAR-LM

    International Nuclear Information System (INIS)

    Aliberti, G.; Yang, W. S.; Stillman, J. A.; Hill, R. N.

    2004-01-01

    Neutronics design studies for a 400 MWt high temperature fast reactor are being performed, utilizing lead coolant, transuranic (TRU) nitride fuel, and HT-9 structural material. Under the main design constraints of long fuel lifetime, natural convection heat transport, semi-autonomous control, and small unit size, parametric studies were performed to maximize the discharge burnup and minimize the burnup reactivity swing. Based on the results of these parametric studies, two point designs were developed for a single-batch once-through fuel cycle; one is a 15 full power year cycle design with core volume of 9.5 cubic meters, and the other is a 12 full power year cycle design with core volume of 7.4 cubic meters. For these two point designs, fuel cycle analyses and reactivity feedback coefficients calculations were performed. The 9.5 cubic meter design achieved an average discharge burnup of 83 MWd/kg with a maximum reactivity change over the lifetime of 0.6%. The peak fast fluence was well within the fast fluence limit of HT9, and both average and peak power densities were well below the estimated limit for natural circulation. The performances of the 7.4 cubic meter design were slightly inferior to this design. To enhance the passive safety characteristics, however, further design improvements need to be made to reduce the coolant density coefficient and to increase the radial expansion coefficient. (authors)

  16. Design Thinking and Cloud Manufacturing: A Study of Cloud Model Sharing Platform Based on Separated Data Log

    Directory of Open Access Journals (Sweden)

    Zhe Wei

    2013-01-01

    Full Text Available To solve the product data consistency problem which is caused by the portable system that cannot conduct real-time update of product data in mobile environment under the mass customization production mode, a new product data optimistic replication method based on log is presented. This paper focuses on the design thinking provider, probing into a manufacturing resource design thinking cloud platform based on manufacturing resource-locating technologies, and also discuss several application scenarios of cloud locating technologies in the manufacturing environment. The actual demand of manufacturing creates a new mode which is service-oriented and has high efficiency and low consumption. Finally, they are different from the crowd-sourcing application model of Local-Motors. The sharing platform operator is responsible for a master plan for the platform, proposing a open interface standard and establishing a service operation mode.

  17. Design Strategies for Aptamer-Based Biosensors

    Science.gov (United States)

    Han, Kun; Liang, Zhiqiang; Zhou, Nandi

    2010-01-01

    Aptamers have been widely used as recognition elements for biosensor construction, especially in the detection of proteins or small molecule targets, and regarded as promising alternatives for antibodies in bioassay areas. In this review, we present an overview of reported design strategies for the fabrication of biosensors and classify them into four basic modes: target-induced structure switching mode, sandwich or sandwich-like mode, target-induced dissociation/displacement mode and competitive replacement mode. In view of the unprecedented advantages brought about by aptamers and smart design strategies, aptamer-based biosensors are expected to be one of the most promising devices in bioassay related applications. PMID:22399891

  18. Using a Studio-Based Pedagogy to Engage Students in the Design of Mobile-Based Media

    Science.gov (United States)

    Mathews, James M.

    2010-01-01

    The article presents a brief overview of the Neighbourhood Game Design Project, a studio-based curriculum intervention aimed at engaging students in the design of place-based mobile games and interactive stories using geo-locative technologies (for example, GPS enabled cell phones). It describes the three curricular components that defined the…

  19. Design, Dynamics, and Workspace of a Hybrid-Driven-Based Cable Parallel Manipulator

    Directory of Open Access Journals (Sweden)

    Bin Zi

    2013-01-01

    Full Text Available The design, dynamics, and workspace of a hybrid-driven-based cable parallel manipulator (HDCPM are presented. The HDCPM is able to perform high efficiency, heavy load, and high-performance motion due to the advantages of both the cable parallel manipulator and the hybrid-driven planar five-bar mechanism. The design is performed according to theories of mechanism structure synthesis for cable parallel manipulators. The dynamic formulation of the HDCPM is established on the basis of Newton-Euler method. The workspace of the manipulator is analyzed additionally. As an example, a completely restrained HDCPM with 3 degrees of freedom is studied in simulation in order to verify the validity of the proposed design, workspace, and dynamic analysis. The simulation results, compared with the theoretical analysis, and the case study previously performed show that the manipulator design is reasonable and the mathematical models are correct, which provides the theoretical basis for future physical prototype and control system design.

  20. Design of a space-based infrared imaging interferometer

    Science.gov (United States)

    Hart, Michael; Hope, Douglas; Romeo, Robert

    2017-07-01

    Present space-based optical imaging sensors are expensive. Launch costs are dictated by weight and size, and system design must take into account the low fault tolerance of a system that cannot be readily accessed once deployed. We describe the design and first prototype of the space-based infrared imaging interferometer (SIRII) that aims to mitigate several aspects of the cost challenge. SIRII is a six-element Fizeau interferometer intended to operate in the short-wave and midwave IR spectral regions over a 6×6 mrad field of view. The volume is smaller by a factor of three than a filled-aperture telescope with equivalent resolving power. The structure and primary optics are fabricated from light-weight space-qualified carbon fiber reinforced polymer; they are easy to replicate and inexpensive. The design is intended to permit one-time alignment during assembly, with no need for further adjustment once on orbit. A three-element prototype of the SIRII imager has been constructed with a unit telescope primary mirror diameter of 165 mm and edge-to-edge baseline of 540 mm. The optics, structure, and interferometric signal processing principles draw on experience developed in ground-based astronomical applications designed to yield the highest sensitivity and resolution with cost-effective optical solutions. The initial motivation for the development of SIRII was the long-term collection of technical intelligence from geosynchronous orbit, but the scalable nature of the design will likely make it suitable for a range of IR imaging scenarios.