Five diseases, one vaccine - a boost for emerging livestock farmers

International Development Research Centre (IDRC) Digital Library (Canada)

12 of the 16 most devastating animal diseases ... good use of livestock vaccines, emerging ... T Chetty, S Goga & A Mather (graphic design by C Lombard) .... Emerging farmers discussing an information pamphlet developed within the project.

Boosted tops at ATLAS

CERN Document Server

Villaplana, M; The ATLAS collaboration

2011-01-01

A sample of candidate events for highly boosted top quarks is selected following the standard ATLAS selection for semi-leptonic ttbar events plus a requirement that the invariant mass of the reconstructed ttbar pair is greater than 700 GeV. Event displays are presented for the most promising candidates, as well as quantitative results for observables designed to isolate a boosted top quark signal.

Optimal Design of a Resonance-Based Voltage Boosting Rectifier for Wireless Power Transmission.

Science.gov (United States)

Lim, Jaemyung; Lee, Byunghun; Ghovanloo, Maysam

2018-02-01

This paper presents the design procedure for a new multi-cycle resonance-based voltage boosting rectifier (MCRR) capable of delivering a desired amount of power to the load (PDL) at a designated high voltage (HV) through a loosely-coupled inductive link. This is achieved by shorting the receiver (Rx) LC-tank for several cycles to harvest and accumulate the wireless energy in the RX inductor before boosting the voltage by breaking the loop and transferring the energy to the load in a quarter cycle. By optimizing the geometries of the transmitter (Tx) and Rx coils and the number of cycles, N , for energy harvesting, through an iterative design procedure, the MCRR can achieve the highest PDL under a given set of design constraints. Governing equations in the MCRR operation are derived to identify key specifications and the design guidelines. Using an exemplary set of specs, the optimized MCRR was able to generate 20.9 V DC across a 100 kΩ load from a 1.8 V p , 6.78 MHz sinusoid input in the ISM-band at a Tx/Rx coil separation of 1.3 cm, power transfer efficiency (PTE) of 2.2%, and N = 9 cycles. At the same coil distance and loading, coils optimized for a conventional half-wave rectifier (CHWR) were able to reach only 13.6 V DC from the same source.

Designing of new structure PID controller of boost converter for solar photovoltaic stability

Science.gov (United States)

Shabrina, Hanifati Nur; Setiawan, Eko Adhi; Sabirin, Chip Rinaldi

2017-03-01

Nowadays, the utilization of renewable energy as the source on distributed generation system is increasing. It aims to reduce reliance and power losses from utility grid and improve power stability in near loads. One example of renewable energy technology that have been highly proven on the market is solar photovoltaic (PV). This technology converts photon from sunlight into electricity. However, the fluctuation of solar radiation that often occurs become the main problem for this system. Due to this condition, the power conversion is needed to convert the change frequently in photovoltaic panel into a stable voltage to the system. Developing control of boost converter has important role to keep ability of system stabilization. A conventional PID (Proportional, Integral, Derivative) control is mostly used to achieve this goal. In this research, a design of new structure PID controller of boost converter is offered to better optimize system stability comparing to the conventional PID. Parameters obtained from this PID structure have been successfully yield a stable boost converter output at 200 V with 10% overshoot, 1.5 seconds of settling time, and 1.5% of steady-state error.

Buck-Boost Current-Source Inverters With Diode-Inductor Network

DEFF Research Database (Denmark)

Gao, Feng; Liang, Chao; Loh, Poh Chiang

2009-01-01

This paper presents a number of novel currentsource inverters (CSIs) with enhanced current buck-boost capability. By adding a unique diode-inductor network between the inverter circuitry and current-boost elements, the proposed buck-boost CSIs demonstrate a doubling of current-boost capability......, as compared with other recently reported buck-boost CSIs. For controlling the proposed CSIs, two modulation schemes are designed for achieving either optimized harmonic performance or minimized commutation count without influencing the inverter current buck-boost gain. These theoretical findings were...

Boosting BCG-primed responses with a subunit Apa vaccine during the waning phase improves immunity and imparts protection against Mycobacterium tuberculosis.

Science.gov (United States)

Nandakumar, Subhadra; Kannanganat, Sunil; Dobos, Karen M; Lucas, Megan; Spencer, John S; Amara, Rama Rao; Plikaytis, Bonnie B; Posey, James E; Sable, Suraj B

2016-05-13

Heterologous prime-boosting has emerged as a powerful vaccination approach against tuberculosis. However, optimal timing to boost BCG-immunity using subunit vaccines remains unclear in clinical trials. Here, we followed the adhesin Apa-specific T-cell responses in BCG-primed mice and investigated its BCG-booster potential. The Apa-specific T-cell response peaked 32-52 weeks after parenteral or mucosal BCG-priming but waned significantly by 78 weeks. A subunit-Apa-boost during the contraction-phase of BCG-response had a greater effect on the magnitude and functional quality of specific cellular and humoral responses compared to a boost at the peak of BCG-response. The cellular response increased following mucosal BCG-prime-Apa-subunit-boost strategy compared to Apa-subunit-prime-BCG-boost approach. However, parenteral BCG-prime-Apa-subunit-boost by a homologous route was the most effective strategy in-terms of enhancing specific T-cell responses during waning in the lung and spleen. Two Apa-boosters markedly improved waning BCG-immunity and significantly reduced Mycobacterium tuberculosis burdens post-challenge. Our results highlight the challenges of optimization of prime-boost regimens in mice where BCG drives persistent immune-activation and suggest that boosting with a heterologous vaccine may be ideal once the specific persisting effector responses are contracted. Our results have important implications for design of prime-boost regimens against tuberculosis in humans.

Two-inductor boost and buck converters

Science.gov (United States)

White, J. L.; Muldoon, W. J.

The derivation, analysis and design of a coupled inductor boost converter is presented. Aspects of the qualitative ac behavior of coupled inductor converters are discussed. Considerations for the design of the magnetics for such converters are addressed.

Early boost and slow consolidation in motor skill learning.

Science.gov (United States)

Hotermans, Christophe; Peigneux, Philippe; Maertens de Noordhout, Alain; Moonen, Gustave; Maquet, Pierre

2006-01-01

Motorskill learning is a dynamic process that continues covertly after training has ended and eventually leads to delayed increments in performance. Current theories suggest that this off-line improvement takes time and appears only after several hours. Here we show an early transient and short-lived boost in performance, emerging as early as 5-30 min after training but no longer observed 4 h later. This early boost is predictive of the performance achieved 48 h later, suggesting its functional relevance for memory processes.

Modeling and Simulation of Buck-Boost Converter with Voltage Feedback Control

Directory of Open Access Journals (Sweden)

Zhou Xuelian

2015-01-01

Full Text Available In order to design the control system, it is necessary to have an exact model of buck-boost converter. This paper put forward the transfer function model of buck-boost converter by the state-space average method. The open-loop transfer function model of uncompensated system is deduced according to the mathematic model of the buck-boost converter, the controller is designed according to frequency domain. The phase and magnitude margin of the open-loop system of the buck-boost converter with compensator have both been increased. After compensating, this control system has the advantages of small overshoot and short settling time. It can also improve control system’s real time property and anti-interference ability.

Movement of the cervix in after-loading brachytherapy: implications for designing external-beam radiotherapy boost fields.

Science.gov (United States)

Hombaiah, U; Blake, P; Bidmead, M

2006-05-01

Women with invasive carcinoma of the cervix treated by chemo-radiotherapy and brachytherapy may also receive a pelvic sidewall boost using a midline shield (MLS). The purpose of this study was to assess the usefulness of implanted gold grains in detecting the movement of the cervix caused by the insertion of low-dose-rate brachytherapy applicators, and its implications in designing the MLS. The medical records of 42 women with various stages of cervical carcinoma, who were treated by radical chemo-radiotherapy, were reviewed. All of these women underwent examination under anaesthesia (EUA) and a gold-grain insertion to demarcate the vaginal tumour extent, in the antero-posterior and lateral planes, before starting external-beam radiotherapy. The isocentric orthogonal films (simulator films) of external radiotherapy and brachytherapy were compared to assess the change in position of the gold grains and the consequences for the design of the MLS for parametrial and pelvic sidewall boosts. A significant shift in the position of the gold grains was noted in both the x (lateral) and the y (cranial/caudal) axes. The median shift of the midline, right and left lateral gold grains was 4.5, 5 and 7 mm in the x axis, whereas it was 10, 8 and 9.5 mm in the y axis, respectively. The median shift in the x and y axes was 5.5 and 9 mm, ranging from 1 to 40 mm and 1 to 45 mm, respectively. The gold grains were shifted cranially in 34 (80%) and laterally in 29 (69%) women. Thirty-two women (76.2%) received parametrial boost radiotherapy, of which 25 (59.5%) women had a customised, pear-shaped shield, and the remaining seven (16.7%) had a straight-sided, rectangular MLS. Four women (9.5%) relapsed locally, and three of them had been treated using a customised shield. In two of these four women, there was an absolute under-dosage of the central pelvis at the tip of the intra-uterine tube by 50% of the parametrial boost dose (5.4 Gy/3 fractions/3 days). Insertion of the gold grains

Nudging and Boosting: Steering or Empowering Good Decisions.

Science.gov (United States)

Hertwig, Ralph; Grüne-Yanoff, Till

2017-11-01

In recent years, policy makers worldwide have begun to acknowledge the potential value of insights from psychology and behavioral economics into how people make decisions. These insights can inform the design of nonregulatory and nonmonetary policy interventions-as well as more traditional fiscal and coercive measures. To date, much of the discussion of behaviorally informed approaches has emphasized "nudges," that is, interventions designed to steer people in a particular direction while preserving their freedom of choice. Yet behavioral science also provides support for a distinct kind of nonfiscal and noncoercive intervention, namely, "boosts." The objective of boosts is to foster people's competence to make their own choices-that is, to exercise their own agency. Building on this distinction, we further elaborate on how boosts are conceptually distinct from nudges: The two kinds of interventions differ with respect to (a) their immediate intervention targets, (b) their roots in different research programs, (c) the causal pathways through which they affect behavior, (d) their assumptions about human cognitive architecture, (e) the reversibility of their effects, (f) their programmatic ambitions, and (g) their normative implications. We discuss each of these dimensions, provide an initial taxonomy of boosts, and address some possible misconceptions.

Research on Power Factor Correction Boost Inductor Design Optimization – Efficiency vs. Power Density

DEFF Research Database (Denmark)

Li, Qingnan; Andersen, Michael A. E.; Thomsen, Ole Cornelius

2011-01-01

Nowadays, efficiency and power density are the most important issues for Power Factor Correction (PFC) converters development. However, it is a challenge to reach both high efficiency and power density in a system at the same time. In this paper, taking a Bridgeless PFC (BPFC) as an example......, a useful compromise between efficiency and power density of the Boost inductors on 3.2kW is achieved using an optimized design procedure. The experimental verifications based on the optimized inductor are carried out from 300W to 3.2kW at 220Vac input....

Rational Design and Synthesis of Efficient Sunscreens To Boost the Solar Protection Factor.

Science.gov (United States)

Losantos, Raúl; Funes-Ardoiz, Ignacio; Aguilera, José; Herrera-Ceballos, Enrique; García-Iriepa, Cristina; Campos, Pedro J; Sampedro, Diego

2017-03-01

Skin cancer incidence has been increasing in the last decades, but most of the commercial formulations used as sunscreens are designed to protect only against solar erythema. Many of the active components present in sunscreens show critical weaknesses, such as low stability and toxicity. Thus, the development of more efficient components is an urgent health necessity and an attractive industrial target. We have rationally designed core moieties with increased photoprotective capacities and a new energy dissipation mechanism. Using these scaffolds, we have synthesized a series of compounds with tunable properties suitable for their use in sunscreens, and enhanced properties in terms of stability, light energy dissipation, and toxicity. Moreover, some representative compounds were included in final sunscreen formulations and a relevant solar protection factor boost was measured. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The influence of the boost in breast-conserving therapy on cosmetic outcome in the EORTC 'boost versus no boost' trial

International Nuclear Information System (INIS)

Vrieling, Conny; Collette, Laurence; Fourquet, Alain; Hoogenraad, Willem J.; Horiot, Jean-Claude; Jager, Jos J.; Pierart, Marianne; Poortmans, Philip M.; Struikmans, Henk; Hulst, Marleen van der; Schueren, Emmanuel van der; Bartelink, Harry

1999-01-01

Purpose: To evaluate the influence of a radiotherapy boost on the cosmetic outcome after 3 years of follow-up in patients treated with breast-conserving therapy (BCT). Methods and Materials: In EORTC trial 22881/10882, 5569 Stage I and II breast cancer patients were treated with tumorectomy and axillary dissection, followed by tangential irradiation of the breast to a dose of 50 Gy in 5 weeks, at 2 Gy per fraction. Patients having a microscopically complete tumor excision were randomized between no boost and a boost of 16 Gy. The cosmetic outcome was evaluated by a panel, scoring photographs of 731 patients taken soon after surgery and 3 years later, and by digitizer measurements, measuring the displacement of the nipple of 3000 patients postoperatively and of 1141 patients 3 years later. Results: There was no difference in the cosmetic outcome between the two treatment arms after surgery, before the start of radiotherapy. At 3-year follow-up, both the panel evaluation and the digitizer measurements showed that the boost had a significant adverse effect on the cosmetic result. The panel evaluation at 3 years showed that 86% of patients in the no-boost group had an excellent or good global result, compared to 71% of patients in the boost group (p = 0.0001). The digitizer measurements at 3 years showed a relative breast retraction assessment (pBRA) of 7.6 pBRA in the no-boost group, compared to 8.3 pBRA in the boost group, indicating a worse cosmetic result in the boost group at follow-up (p = 0.04). Conclusions: These results showed that a boost dose of 16 Gy had a negative, but limited, impact on the cosmetic outcome after 3 years

Analysis, Design, Modeling, and Control of an Interleaved-Boost Full-Bridge Three-Port Converter for Hybrid Renewable Energy Systems

DEFF Research Database (Denmark)

Mira Albert, Maria del Carmen; Zhang, Zhe; Knott, Arnold

2017-01-01

This paper presents the design, modeling, and control of an isolated dc-dc three-port converter (TPC) based on an interleaved-boost full-bridge converter with pulsewidth modulation (PWM) and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven...

Identifying the emergence of design ideas

DEFF Research Database (Denmark)

Inie, Nanna

This position paper outlines four types of design idea indicators that provide four starting points for exploration of the emergence of design ideas from a micro perspective. The results are derived from two empirical studies of design processes. The research builds on the assumption that we need...... better understanding and definition of design idea emergence and transformation in order to systematically explore the creative process....

Boost.Unicode

OpenAIRE

Wien, Erik; Gigstad, Lars Erik

2005-01-01

The project has resulted in a Unicode string library for C++ that abstracts away the complexity of working with Unicode text. The idea behind the project originated from the Boost community's developer mailings lists, and is developed with inclusion into the Boost library collection in mind.

The simultaneous boost technique

International Nuclear Information System (INIS)

Lebesque, J.V.; Keus, R.B.

1991-01-01

Simultaneous boost technique in radiotherapy consists of delivering the boost treatment (additional doses to reduced volumes) simultaneously with the basic (large-field) treatment for all treatment sessions. Both the dose per fraction delivered by basic-treatment fields and by boost-treatment fields have to be reduced to end up with the same total dose in boost volume as in the original schedule, where basic treatment preceded boost treatment. These dose reductions and corresponding weighting factors have been calculated using the linear-quadratic (LQ) model and the concept of Normalized Total Dose (NTD). Relative NTD distributions were computed to evaluate the dose distributions resulting for the simultaneous boost technique with respect to acute and late normal tissue damage and tumor control. For the example of treatment of prostate cancer the weighting factors were calculated on basis of NTD for late normal tissue damage. For treatment of oropharyngeal cancer NTD for acute and normal tissue damage was used to determine the weighting factors. In this last example a theoretical sparing of late normal tissue damage can be demonstrated. Another advantage of simultaneous boost technique is that megavoltage images of the large basic-treatment fields facilitates the determination of the position of the patient with respect to the small boost-treatment fields. (author). 42 refs., 8 figs

Emerging memory technologies design, architecture, and applications

CERN Document Server

2014-01-01

This book explores the design implications of emerging, non-volatile memory (NVM) technologies on future computer memory hierarchy architecture designs. Since NVM technologies combine the speed of SRAM, the density of DRAM, and the non-volatility of Flash memory, they are very attractive as the basis for future universal memories. This book provides a holistic perspective on the topic, covering modeling, design, architecture and applications. The practical information included in this book will enable designers to exploit emerging memory technologies to improve significantly the performance/power/reliability of future, mainstream integrated circuits. • Provides a comprehensive reference on designing modern circuits with emerging, non-volatile memory technologies, such as MRAM and PCRAM; • Explores new design opportunities offered by emerging memory technologies, from a holistic perspective; • Describes topics in technology, modeling, architecture and applications; • Enables circuit designers to ex...

A Reconfigurable Buck, Boost, and Buck-Boost Converter: Unified Model and Robust Controller

Directory of Open Access Journals (Sweden)

Martín Antonio Rodríguez Licea

2018-01-01

Full Text Available The need for reconfigurable, high power density, and low-cost configurations of DC-DC power electronic converters (PEC in areas such as the transport electrification and the use of renewable energy has spread out the requirement to incorporate in a single circuit several topologies, which generally result in an increment of complexity about the modeling, control, and stability analyses. In this paper, a reconfigurable topology is presented which can be applied in alterative/changing power conversion scenarios and consists of a reconfigurable Buck, Boost, and Buck-Boost DC-DC converter (RBBC. A unified averaged model of the RBBC is obtained, a robust controller is designed through a polytopic representation, and a Lyapunov based switched stability analysis of the closed-loop system is presented. The reported RBBC provides a wide range of voltage operation, theoretically from -∞ to ∞ volts with a single power source. Robust stability, even under arbitrarily fast (bounded parameter variations and reconfiguration changes, is reported including numerical and experimental results. The main advantages of the converter and the robust controller proposed are simple design, robustness against abrupt changes in the parameters, and low cost.

Boost.Asio C++ network programming

CERN Document Server

Torjo, John

2013-01-01

What you want is an easy level of abstraction, which is just what this book provides in conjunction with Boost.Asio. Switching to Boost.Asio is just a few extra #include directives away, with the help of this practical and engaging guide.This book is great for developers that need to do network programming, who don't want to delve into the complicated issues of a raw networking API. You should be familiar with core Boost concepts, such as smart pointers and shared_from_this, resource classes (noncopyable), functors and boost::bind, boost mutexes, and the boost date/time library. Readers should

Early Boost and Slow Consolidation in Motor Skill Learning

Science.gov (United States)

Hotermans, Christophe; Peigneux, Philippe; de Noordhout, Alain Maertens; Moonen, Gustave; Maquet, Pierre

2006-01-01

Motor skill learning is a dynamic process that continues covertly after training has ended and eventually leads to delayed increments in performance. Current theories suggest that this off-line improvement takes time and appears only after several hours. Here we show an early transient and short-lived boost in performance, emerging as early as…

Boosting foundations and algorithms

CERN Document Server

Schapire, Robert E

2012-01-01

Boosting is an approach to machine learning based on the idea of creating a highly accurate predictor by combining many weak and inaccurate "rules of thumb." A remarkably rich theory has evolved around boosting, with connections to a range of topics, including statistics, game theory, convex optimization, and information geometry. Boosting algorithms have also enjoyed practical success in such fields as biology, vision, and speech processing. At various times in its history, boosting has been perceived as mysterious, controversial, even paradoxical.

A THREE-PHASE BOOST DC-AC CONVERTER

African Journals Online (AJOL)

dc-ac converter (inverter) based on the dc-dc boost converters. ... Sliding mode controllers are designed to perform a robust control for the ... Computer simulations and spectral analysis demon- ... the conventional three-phase buck inverter,.

Diet-boosting foods

Science.gov (United States)

Obesity - diet-boosting foods; Overweight - diet-boosting foods ... Low-fat and nonfat milk, yogurt, and cottage cheese are healthy sources of calcium, vitamin D , and potassium. Unlike sweetened drinks with extra calories, milk ...

Design of emergency shield

International Nuclear Information System (INIS)

Soliman, S.E.

1993-01-01

Manufacturing of an emergency movable shield in the hot laboratories center is urgently needed for the safety of personnel in case of accidents or spilling of radioactive materials. In this report, a full design for an emergency shield is presented and the corresponding dose rates behind the shield for different activities (from 1 mCi to 5 Ci) was calculated by using micro shield computer code. 4 figs., 1 tab

Boosted Multivariate Trees for Longitudinal Data

Science.gov (United States)

Pande, Amol; Li, Liang; Rajeswaran, Jeevanantham; Ehrlinger, John; Kogalur, Udaya B.; Blackstone, Eugene H.; Ishwaran, Hemant

2017-01-01

Machine learning methods provide a powerful approach for analyzing longitudinal data in which repeated measurements are observed for a subject over time. We boost multivariate trees to fit a novel flexible semi-nonparametric marginal model for longitudinal data. In this model, features are assumed to be nonparametric, while feature-time interactions are modeled semi-nonparametrically utilizing P-splines with estimated smoothing parameter. In order to avoid overfitting, we describe a relatively simple in sample cross-validation method which can be used to estimate the optimal boosting iteration and which has the surprising added benefit of stabilizing certain parameter estimates. Our new multivariate tree boosting method is shown to be highly flexible, robust to covariance misspecification and unbalanced designs, and resistant to overfitting in high dimensions. Feature selection can be used to identify important features and feature-time interactions. An application to longitudinal data of forced 1-second lung expiratory volume (FEV1) for lung transplant patients identifies an important feature-time interaction and illustrates the ease with which our method can find complex relationships in longitudinal data. PMID:29249866

An Original Transformer and Switched-Capacitor (T & SC-Based Extension for DC-DC Boost Converter for High-Voltage/Low-Current Renewable Energy Applications: Hardware Implementation of a New T & SC Boost Converter

Directory of Open Access Journals (Sweden)

Sanjeevikumar Padmanaban

2018-03-01

Full Text Available In this article a new Transformer and Switched Capacitor-based Boost Converter (T & SC-BC is proposed for high-voltage/low-current renewable energy applications. The proposed T & SC-BC is an original extension for DC-DC boost converter which is designed by utilizing a transformer and switched capacitor (T & SC. Photovoltaic (PV energy is a fast emergent segment among the renewable energy systems. The proposed T & SC-BC combines the features of the conventional boost converter and T & SC to achieve a high voltage conversion ratio. A Maximum Power Point Tracking (MPPT controller is compulsory and necessary in a PV system to extract maximum power. Thus, a photovoltaic MPPT control mechanism also articulated for the proposed T & SC-BC. The voltage conversion ratio (Vo/Vin of proposed converter is (1 + k/(1 − D where, k is the turns ratio of the transformer and D is the duty cycle (thus, the converter provides 9.26, 13.88, 50/3 voltage conversion ratios at 78.4 duty cycle with k = 1, 2, 2.6, respectively. The conspicuous features of proposed T & SC-BC are: (i a high voltage conversion ratio (Vo/Vin; (ii continuous input current (Iin; (iii single switch topology; (iv single input source; (v low drain to source voltage (VDS rating of control switch; (vi a single inductor and a single untapped transformer are used. Moreover, the proposed T & SC-BC topology was compared with recently addressed DC-DC converters in terms of number of components, cost, voltage conversion ratio, ripples, efficiency and power range. Simulation and experimental results are provided which validate the functionality, design and concept of the proposed approach.

Design Methods in the Emergent City

DEFF Research Database (Denmark)

Samson, Kristine

The paper seeks to define urban design in relation to the specific challenges of emerging cities. Through a case study of Mudo Coletivos temporary structure, Bolha Imobiliaria, and the making of it, I wish to outline a design approach for urban design in cities lacking public spaces. Urban design...... is understood in a broad sense, not as architectural design but as spatial design and artistic interventions in public space. Through the paper I will address how the designer can co-create and reassemble existing urban spaces through design acts. The approach suggests a situated design methodology but is based...... on a theoretical understanding. It is my belief that the designer, by looking into the emergent properties of urban spaces, instead of its physical and cartographical outlines, can see her work as a processual intervention in the city rather than durable object design....

Design and comparison of a 10-kW interleaved boost converter for PV application using Si and SiC devices

NARCIS (Netherlands)

Chandra Mouli, G.R.; Schijffelen, Jos H.; Bauer, P.; Zeman, M.

2017-01-01

Grid-connected photovoltaic (PV) inverters have a dc/dc converter connected to the PV for executing the maximum power point tracking. The design of an interleaved boost converter (IBC) with three switching legs for a 10-kW PV inverter is presented in this paper. This paper shows how the use of

Design and Control of a Buck–Boost Charger-Discharger for DC-Bus Regulation in Microgrids

Directory of Open Access Journals (Sweden)

Carlos Andrés Ramos-Paja

2017-11-01

Full Text Available In DC and hybrid microgrids (MG, the DC-bus regulation using Energy Storage Devices (ESD is important for the stable operation of both the generators and loads. There are multiple commercial voltage levels for both ESD and DC-bus; therefore, the ESD voltage may be higher, equal or lower than the DC-bus voltage depending on the application. Moreover, most of the ESD converter controllers are linear-based, hence they ensure stability in a limited operation range. This paper proposes a system to regulate the DC-bus voltage of an MG accounting for any voltage relation between the ESD and the DC-bus voltage. The proposed system is formed by an ESD connected to a DC-bus through a bidirectional Buck–Boost converter, which is regulated by a Sliding-Mode Controller (SMC to ensure the system stability in the entire operation range. The SMC drives the Buck–Boost charger–discharger to regulate the DC-bus voltage, at the desired reference value, by charging or discharging the ESD. This paper also provides detailed procedures to design the parameters of both the SMC and the charger–dischager. Finally, simulation and experimental results validate the proposed solution and illustrate its performance.

[The evaluation of academic emergency department design].

Science.gov (United States)

Deniz, Turgut; Aydinuraz, Kuzey; Oktay, Cem; Saygun, Meral; Ağalar, Fatih

2007-01-01

In our study which was based upon a questionnaire, the inner and outer architectural designs of emergency services of Emergency Medicine Departments were investigated. In this descriptive study, a standard questionnaire was sent to 26 Emergency Medicine Departments which were operating at that time. In the questionnaire, the internal, external architectural and functional features were questioned. Answers of 22 Emergency Medicine Departments were analysed. Two Emergency Medicine Departments that were not operating at that time were not included in the study. The analysis of the replies revealed that only 59% (n=13) of the Emergency Medicine Departments were designed as an emergency service prior to the construction. The ambulance parking areas were not suitable in 77% of the emergency units while only 54.5% (n=12) had protection against adverse weather conditions. In only 59% (n=13) of the emergency units, a triage unit was present and in only one of the in only one (4.5%), a decontamination room was available. It was understood that only 32% (n=8) of the emergency units were appropriate in enlarging their capacity taking the local risk factors into consideration. There was a toilette for disabled patients in only 18% (n=4) of the units as well. Considering a 12-year of history of the Emergency Medicine in Turkey, the presence of a lecture room is still 68% (n=15) in emergency departments which reflects that academic efforts in this field is emerging in challenging physical conditions. The results of our study revealed that emergency service architecture was neglected in Turkey and medical care given was precluded by the insufficient architecture. The design of emergency services has to be accomplished under guidance of scientific data and rules taking advices of architects who have knowledge and experience on this field.

Challenges in designing interactive systems for emergency response

DEFF Research Database (Denmark)

Kristensen, Margit; Kyng, Morten; Nielsen, Esben Toftdahl

2007-01-01

and visions as ways to bridge between fieldwork and literature studies on the one hand and the emerging computer based prototypes on the other. Our case concerns design of innovative interactive systems for support in emergency response, including patient identification and monitoring as well as construction......This paper presents research on participatory design of interactive systems for emergency response. We present the work by going through the design method with a focus on the new elements that we developed for the participatory design toolkit, in particular we emphasize the use of challenges...

Distribution-Specific Agnostic Boosting

OpenAIRE

Feldman, Vitaly

2009-01-01

We consider the problem of boosting the accuracy of weak learning algorithms in the agnostic learning framework of Haussler (1992) and Kearns et al. (1992). Known algorithms for this problem (Ben-David et al., 2001; Gavinsky, 2002; Kalai et al., 2008) follow the same strategy as boosting algorithms in the PAC model: the weak learner is executed on the same target function but over different distributions on the domain. We demonstrate boosting algorithms for the agnostic learning framework tha...

Topics in Analysis and Design of Primary Parallel Isolated Boost Converter

DEFF Research Database (Denmark)

Sen, Gokhan

Efficient power processing through power electronics circuits has been a popular academic field for the past decades, especially after “green” vehicle applications based on fuel cells, batteries and super-capacitors emerged as alternative sources of propulsion for transportation. Dc-to-dc convert......Efficient power processing through power electronics circuits has been a popular academic field for the past decades, especially after “green” vehicle applications based on fuel cells, batteries and super-capacitors emerged as alternative sources of propulsion for transportation. Dc...... for such applications due to its simplicity and ability to handle higher currents. Design of magnetic structures like transformers and inductors is part of power electronics engineering in which trade-offs exist between size, price and losses. In higher currents this becomes even more challenging since conventional...... wire wound design approach has some shortcomings. It is possible to use copper foil in windings however this will increase the amount of handcraft during manufacturing; so academic attention was needed for this part of low voltage high current switching converter design. Planar magnetics...

A 1 MEGAWATT POLYPHASE BOOST CONVERTER-MODULATOR FOR KLYSTRON PULSE APPLICATION

International Nuclear Information System (INIS)

Reass, W.A.; Doss, J.D.; Gribble, R.F.

2001-01-01

This paper describes electrical design criteria and first operational results a 140 kV, 1 MW average, 11 MW peak, zero-voltage-switching 20 kHz polyphase bridge, boost converter/modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2300 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three ''H-Bridge'' Insulated Gate Bipolar Transistor (IGBT) switching networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. PWM (pulse width modulation) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt-peaking is used on the transformer secondary to boost output voltage and resonate transformer leakage inductance. With the appropriate transformer leakage inductance and peaking capacitance, zero-voltage-switching of the IGBT's is attained, minimizing switching losses. A review of these design parameters and the first results of the performance characteristics will be presented

Robust loss functions for boosting.

Science.gov (United States)

Kanamori, Takafumi; Takenouchi, Takashi; Eguchi, Shinto; Murata, Noboru

2007-08-01

Boosting is known as a gradient descent algorithm over loss functions. It is often pointed out that the typical boosting algorithm, Adaboost, is highly affected by outliers. In this letter, loss functions for robust boosting are studied. Based on the concept of robust statistics, we propose a transformation of loss functions that makes boosting algorithms robust against extreme outliers. Next, the truncation of loss functions is applied to contamination models that describe the occurrence of mislabels near decision boundaries. Numerical experiments illustrate that the proposed loss functions derived from the contamination models are useful for handling highly noisy data in comparison with other loss functions.

Pulse width modulated buck-boost five-level current source inverters

DEFF Research Database (Denmark)

Blaabjerg, Frede; Gao, F.; Loh, P.C.

2008-01-01

, resulting in the natural balance of input current. For maintaining the normalized volt-sec average unchanged, the alternative phase opposition disposition (APOD) modulation scheme with typical gating signal mapping technique from voltage source inverter (VSI) to CSI can be assumed to control the five......This paper presents new five-level current source inverters (CSIs) with voltage/current buck-boost capability. Being different from the existing multilevel CSI, the proposed CSIs were first designed to regulate the flowing path of dc input current by controlling two additional active switches......-level buck-boost CSIs. Next by observing the hidden current charging path during inductive charging interval under APOD modulation, it is noted that the buck-boost five-level CSI can then be further modified with lesser active component without degrading output performance. To verify the theoretical findings...

Deep Incremental Boosting

OpenAIRE

Mosca, Alan; Magoulas, George D

2017-01-01

This paper introduces Deep Incremental Boosting, a new technique derived from AdaBoost, specifically adapted to work with Deep Learning methods, that reduces the required training time and improves generalisation. We draw inspiration from Transfer of Learning approaches to reduce the start-up time to training each incremental Ensemble member. We show a set of experiments that outlines some preliminary results on some common Deep Learning datasets and discuss the potential improvements Deep In...

Diode-Assisted Buck-Boost Voltage-Source Inverters

DEFF Research Database (Denmark)

Gao, Feng; Loh, Poh Chiang; Teodorescu, Remus

2009-01-01

, a number of diode-assisted inverter variants can be designed with each having its own operational principle and voltage gain expression. For controlling them, a generic modulation scheme that can be used for controlling all diode-assisted variants with minimized harmonic distortion and component stress......This paper proposes a number of diode-assisted buck-boost voltage-source inverters with a unique X-shaped diode-capacitor network inserted between the inverter circuitry and dc source for producing a voltage gain that is comparatively higher than those of other buck-boost conversion techniques....... Using the diode-assisted network, the proposed inverters can naturally configure themselves to perform capacitive charging in parallel and discharging in series to give a higher voltage multiplication factor without compromising waveform quality. In addition, by adopting different front-end circuitries...

Application of a synchronous generator with a boost converter in wind turbines: an experimental overview

DEFF Research Database (Denmark)

Sharma, Ranjan; Rasmussen, Tonny Wederberg; Jensen, Bogi Bech

2012-01-01

An electrical structure of a variable-speed wind turbine based on an externally excited synchronous generator; a passive diode rectifier; and a boost converter is discussed in this study. The clear advantage of such a system is its lower-semi-conductor devices count. A brief theoretical explanation...... of such a system is included. A boost converter normally utilies an inductor (energy storage) to boost the voltage level from its input to a higher output value. This study analyses the possibility of using the generator inductance as a boost inductor. It is discussed and verified in the study that for the given...... switching frequency of the boost converter (fs=1= kHz), the generator sub-transient inductance (not the synchronous inductance) appears as an equivalent inductance seen by the boost converter. The parasitic capacitors present in the generator terminals are often neglected from design issues. It is presented...

Image objects detection based on boosting neural network

NARCIS (Netherlands)

Liang, N.; Hegt, J.A.; Mladenov, V.M.

2010-01-01

This paper discusses the problem of object area detection of video frames. The goal is to design a pixel accurate detector for grass, which could be used for object adaptive video enhancement. A boosting neural network is used for creating such a detector. The resulted detector uses both textural

Improving emergency management through shared information processing - considerations in Emergency Operations Center design

International Nuclear Information System (INIS)

DeBusk, R.E.; Walker, J.A.

1987-01-01

An Emergency Operations Center (EOC) is a shared information processing facility. Although seemingly obvious, many EOCs are designed and operated based on other criteria. The results, measured in terms of response effectiveness, are difficult to determine. A review of some recent disasters reveals a pattern of poor performance for the EOCs involved. These conclusions are tentative because so little research has been done on the design, operation, or evaluation of emergency operations centers. The EOC is not an onsite response command post but a facility removed from the response where tactical and strategic decisions are made based on information from the response site and elsewhere. The EOC is therefore the central focus of emergency information processing and higher-level decision making. Examining existing EOCs, several common functions emerge. These functions can be described in terms of shared information processing. However, many factors impact the design and operation of EOCs. Politics, budgets, and personal ambition are only a few such factors. Examining EOC design and operation in terms of shared information processing operationalized in the seven principal functions within the EOC provides a framework for establishing principles of EOC design and operation. In the response to emergencies such as Bhopal or Chernobyl the stakes are high. Applying new techniques and technologies of management systems can improve the probability of success. This research is a beginning step - to understand how EOCs function, to define the system. Predictive or prescriptive analysis must wait until sufficient empirical data is available to complete a descriptive model for EOC operations

Can you boost your metabolism?

Science.gov (United States)

... this page: //medlineplus.gov/ency/patientinstructions/000893.htm Can you boost your metabolism? To use the sharing ... boosting metabolism than tactics that work. Some myths can backfire. If you think you are burning more ...

Learning Boost C++ libraries

CERN Document Server

Mukherjee, Arindam

2015-01-01

If you are a C++ programmer who has never used Boost libraries before, this book will get you up-to-speed with using them. Whether you are developing new C++ software or maintaining existing code written using Boost libraries, this hands-on introduction will help you decide on the right library and techniques to solve your practical programming problems.

Design Anthropology, Emerging Technologies and Alternative Computational Futures

DEFF Research Database (Denmark)

Smith, Rachel Charlotte

Emerging technologies are providing a new field for design anthropological inquiry that unite experiences, imaginaries and materialities in complex way and demands new approaches to developing sustainable computational futures.......Emerging technologies are providing a new field for design anthropological inquiry that unite experiences, imaginaries and materialities in complex way and demands new approaches to developing sustainable computational futures....

Detection of Illegitimate Emails using Boosting Algorithm

DEFF Research Database (Denmark)

Nizamani, Sarwat; Memon, Nasrullah; Wiil, Uffe Kock

2011-01-01

and spam email detection. For our desired task, we have applied a boosting technique. With the use of boosting we can achieve high accuracy of traditional classification algorithms. When using boosting one has to choose a suitable weak learner as well as the number of boosting iterations. In this paper, we......In this paper, we report on experiments to detect illegitimate emails using boosting algorithm. We call an email illegitimate if it is not useful for the receiver or for the society. We have divided the problem into two major areas of illegitimate email detection: suspicious email detection...

The Emergence of an Amplified Mindset of Design: Implications for Postgraduate Design Education

Science.gov (United States)

Moreira, Mafalda; Murphy, Emma; McAra-McWilliam, Irene

2016-01-01

In a global scenario of complexity, research shows that emerging design practices are changing and expanding, creating a complex and ambiguous disciplinary landscape. This directly impacts on the field of design education, calling for new, flexible models able to tackle future practitioners' needs, unknown markets and emergent societal cultures.…

The performance of the DC motor by the PID controlling PWM DC-DC boost converter

OpenAIRE

Can, Erol; Sayan, Hasan Hüseyin

2017-01-01

This paper presents the PID controlling direct current (DC) to the direct current boost converter feds DC motor which has a 3.68 kW and 240 V of DC voltage input on its characteristics. What is first formed is the boost converter mathematical model at the design stage. Secondly, a mathematical model of the DC motor is created so that the boost converter with the machine can be established and modeled at the Matlab Simulink. The PID controller is considered for arranging a pulse width modulati...

Simple grain mill boosts production and eases women's workload ...

International Development Research Centre (IDRC) Digital Library (Canada)

2013-01-11

Jan 11, 2013 ... Simple grain mill boosts production and eases women's workload ... Farmers also like the design because, unlike other machines, it can be easily adjusted for different millet varieties and sizes. ... Local manufacturing. Discussions have begun with local entrepreneurs to manufacture the grain mill, which ...

Design of an Emergency Shelter

NARCIS (Netherlands)

Kamerling, M.W.

2013-01-01

This paper presents the design of a light and robust temporary emergency shelter with a triangulated polyhedral grid to transfer the lateral and vertical loads efficiently. To simplify the construction the variety of the elements is minimized, only two sizes of elements are applied. For the

Design of an Emergency Footbridge

NARCIS (Netherlands)

Rihal, S.; Kamerling, M.W.

2014-01-01

This paper will describe the design of a temporary emergency floating footbridge, to be made when the infrastructure is destroyed by a flood, hurricane, tsunami or any other disaster. The bridge is made of identical floating modules. The modules are composed of prefabricated elements: two trusses, a

Boost Converter with Active Snubber Network

Directory of Open Access Journals (Sweden)

HIMMELSTOSS, F. A.

2017-02-01

Full Text Available A new concept for reducing the losses in a boost converter is described. With the help of an auxiliary switch and a resonant circuit, zero-voltage switching at turn-off and zero-current switching during turn-on are achieved. The modes of the circuit are shown in detail. The energy recovery of the turn-off is analyzed and the recovered energy is calculated; an optimized switching concept therefore is described. The influence of the parasitic capacity of the switch is discussed. Dimensioning hints for the converter and the design of the recuperation circuit are given. A bread-boarded design shows the functional efficiency of the concept.

High Current Planar Transformer for Very High Efficiency Isolated Boost DC-DC Converters

DEFF Research Database (Denmark)

Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

2014-01-01

This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac-resistance a......This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac......-resistance and transformer leakage inductance. Design and optimization procedures are validated based on an experimental prototype of a 6 kW dcdc isolated full bridge boost converter developed on fully planar magnetics. The prototype is rated at 30-80 V 0-80 A on the low voltage side and 700-800 V on the high voltage side...... with a peak efficiency of 97.8% at 80 V 3.5 kW. Results highlights that thick copper windings can provide good performance at low switching frequencies due to the high transformer filling factor. PCB windings can also provide very high efficiency if stacked in parallel utilizing the transformer winding window...

Is it beneficial to selectively boost high-risk tumor subvolumes? A comparison of selectively boosting high-risk tumor subvolumes versus homogeneous dose escalation of the entire tumor based on equivalent EUD plans

International Nuclear Information System (INIS)

Kim, Yusung; To me, Wolfgang A.

2008-01-01

Purpose. To quantify and compare expected local tumor control and expected normal tissue toxicities between selective boosting IMRT and homogeneous dose escalation IMRT for the case of prostate cancer. Methods. Four different selective boosting scenarios and three different high-risk tumor subvolume geometries were designed to compare selective boosting and homogeneous dose escalation IMRT plans delivering the same equivalent uniform dose (EUD) to the entire PTV. For each scenario, differences in tumor control probability between both boosting strategies were calculated for the high-risk tumor subvolume and remaining low-risk PTV, and were visualized using voxel based iso-TCP maps. Differences in expected rectal and bladder complications were quantified using radiobiological indices (generalized EUD (gEUD) and normal tissue complication probability (NTCP)) as well as %-volumes. Results. For all investigated scenarios and high-risk tumor subvolume geometries, selective boosting IMRT improves expected TCP compared to homogeneous dose escalation IMRT, especially when lack of control of the high-risk tumor subvolume could be the cause for tumor recurrence. Employing, selective boosting IMRT significant increases in expected TCP can be achieved for the high-risk tumor subvolumes. The three conventional selective boosting IMRT strategies, employing physical dose objectives, did not show significant improvement in rectal and bladder sparing as compared to their counterpart homogeneous dose escalation plans. However, risk-adaptive optimization, utilizing radiobiological objective functions, resulted in reduction in NTCP for the rectum when compared to its corresponding homogeneous dose escalation plan. Conclusions. Selective boosting is a more effective method than homogeneous dose escalation for achieving optimal treatment outcomes. Furthermore, risk-adaptive optimization increases the therapeutic ratio as compared to conventional selective boosting IMRT

Can emergency medicine research benefit from adaptive design clinical trials?

Science.gov (United States)

Flight, Laura; Julious, Steven A; Goodacre, Steve

2017-04-01

Adaptive design clinical trials use preplanned interim analyses to determine whether studies should be stopped or modified before recruitment is complete. Emergency medicine trials are well suited to these designs as many have a short time to primary outcome relative to the length of recruitment. We hypothesised that the majority of published emergency medicine trials have the potential to use a simple adaptive trial design. We reviewed clinical trials published in three emergency medicine journals between January 2003 and December 2013. We determined the proportion that used an adaptive design as well as the proportion that could have used a simple adaptive design based on the time to primary outcome and length of recruitment. Only 19 of 188 trials included in the review were considered to have used an adaptive trial design. A total of 154/165 trials that were fixed in design had the potential to use an adaptive design. Currently, there seems to be limited uptake in the use of adaptive trial designs in emergency medicine despite their potential benefits to save time and resources. Failing to take advantage of adaptive designs could be costly to patients and research. It is recommended that where practical and logistical considerations allow, adaptive designs should be used for all emergency medicine clinical trials. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

BoostEMM : Transparent boosting using exceptional model mining

NARCIS (Netherlands)

van der Zon, S.B.; Zeev Ben Mordehay, O.; Vrijdag, T.S.; van Ipenburg, W.; Veldsink, J.; Duivesteijn, W.; Pechenizkiy, M.; Bordino, I.; Caldarelli, G.; Fumarola, F.; Gullo, F.; Squartini, T.

2017-01-01

Boosting is an iterative ensemble-learning paradigm. Every iteration, a weak predictor learns a classification task, taking into account performance achieved in previous iterations. This is done by assigning weights to individual records of the dataset, which are increased if the record is

Analysis of high voltage step-up nonisolated DC-DC boost converters

Science.gov (United States)

Alisson Alencar Freitas, Antônio; Lessa Tofoli, Fernando; Junior, Edilson Mineiro Sá; Daher, Sergio; Antunes, Fernando Luiz Marcelo

2016-05-01

A high voltage step-up nonisolated DC-DC converter based on coupled inductors suitable to photovoltaic (PV) systems applications is proposed in this paper. Considering that numerous approaches exist to extend the voltage conversion ratio of DC-DC converters that do not use transformers, a detailed comparison is also presented among the proposed converter and other popular topologies such as the conventional boost converter and the quadratic boost converter. The qualitative analysis of the coupled-inductor-based topology is developed so that a design procedure can be obtained, from which an experimental prototype is implemented to validate the theoretical assumptions.

Participatory Design in Emergency Medical Service: Designing for Future Practice

DEFF Research Database (Denmark)

Kristensen, Margit; Kyng, Morten; Palen, Leysia Ann

2006-01-01

address challenges identified by disaster sociologists when designing for major incidents. Through qualitative research and participatory design, we have ex-amined the features of EMS work and technology use in different emergency situations from the perspective of mul-tiple actors. We conceptualize...... victims in incidents—and particularly in major incidents, where on-site medical as-sessments is highly incomplete—as boundary objects over which the complex and imperfect work of coordination is done. As an outcome of our participatory design approach, we describe a set of designs in support of future EMS...

AlignerBoost: A Generalized Software Toolkit for Boosting Next-Gen Sequencing Mapping Accuracy Using a Bayesian-Based Mapping Quality Framework.

Directory of Open Access Journals (Sweden)

Qi Zheng

2016-10-01

Full Text Available Accurate mapping of next-generation sequencing (NGS reads to reference genomes is crucial for almost all NGS applications and downstream analyses. Various repetitive elements in human and other higher eukaryotic genomes contribute in large part to ambiguously (non-uniquely mapped reads. Most available NGS aligners attempt to address this by either removing all non-uniquely mapping reads, or reporting one random or "best" hit based on simple heuristics. Accurate estimation of the mapping quality of NGS reads is therefore critical albeit completely lacking at present. Here we developed a generalized software toolkit "AlignerBoost", which utilizes a Bayesian-based framework to accurately estimate mapping quality of ambiguously mapped NGS reads. We tested AlignerBoost with both simulated and real DNA-seq and RNA-seq datasets at various thresholds. In most cases, but especially for reads falling within repetitive regions, AlignerBoost dramatically increases the mapping precision of modern NGS aligners without significantly compromising the sensitivity even without mapping quality filters. When using higher mapping quality cutoffs, AlignerBoost achieves a much lower false mapping rate while exhibiting comparable or higher sensitivity compared to the aligner default modes, therefore significantly boosting the detection power of NGS aligners even using extreme thresholds. AlignerBoost is also SNP-aware, and higher quality alignments can be achieved if provided with known SNPs. AlignerBoost's algorithm is computationally efficient, and can process one million alignments within 30 seconds on a typical desktop computer. AlignerBoost is implemented as a uniform Java application and is freely available at https://github.com/Grice-Lab/AlignerBoost.

AlignerBoost: A Generalized Software Toolkit for Boosting Next-Gen Sequencing Mapping Accuracy Using a Bayesian-Based Mapping Quality Framework.

Science.gov (United States)

Zheng, Qi; Grice, Elizabeth A

2016-10-01

Accurate mapping of next-generation sequencing (NGS) reads to reference genomes is crucial for almost all NGS applications and downstream analyses. Various repetitive elements in human and other higher eukaryotic genomes contribute in large part to ambiguously (non-uniquely) mapped reads. Most available NGS aligners attempt to address this by either removing all non-uniquely mapping reads, or reporting one random or "best" hit based on simple heuristics. Accurate estimation of the mapping quality of NGS reads is therefore critical albeit completely lacking at present. Here we developed a generalized software toolkit "AlignerBoost", which utilizes a Bayesian-based framework to accurately estimate mapping quality of ambiguously mapped NGS reads. We tested AlignerBoost with both simulated and real DNA-seq and RNA-seq datasets at various thresholds. In most cases, but especially for reads falling within repetitive regions, AlignerBoost dramatically increases the mapping precision of modern NGS aligners without significantly compromising the sensitivity even without mapping quality filters. When using higher mapping quality cutoffs, AlignerBoost achieves a much lower false mapping rate while exhibiting comparable or higher sensitivity compared to the aligner default modes, therefore significantly boosting the detection power of NGS aligners even using extreme thresholds. AlignerBoost is also SNP-aware, and higher quality alignments can be achieved if provided with known SNPs. AlignerBoost's algorithm is computationally efficient, and can process one million alignments within 30 seconds on a typical desktop computer. AlignerBoost is implemented as a uniform Java application and is freely available at https://github.com/Grice-Lab/AlignerBoost.

Analysis of current-bidirectional buck-boost based switch-mode audio amplifier

DEFF Research Database (Denmark)

Bolten Maizonave, Gert; Andersen, Michael A. E.; Kjærgaard, Claus

2011-01-01

The following studdy was carried out in order to assses quantitatively the performannce of the buck--boost converter whhen used as swiitch-mode audio amplifier. It comprises of, to beggin with, the de limitation of design criteria bassed on the state of-the-art solution, which is based...... in a differential mode buckbased amplifier with a boost converter as power supply. The averaged switch modelling of the differential mode current bidirectional topology is also used, in order to analyze the steady state and frequency-wise behaviour of this converter and parameterize it to meet the design criteria....... Next, several piecewise-linear siimulation resultss are shown with detail enough to emphasize the features of the converter. A simple prototype is implemented to verify the main predicted features. Presently no previous publicat ion could be found containing a thorough analysis of this topology...

Leadership emergence in engineering design teams.

Science.gov (United States)

Guastello, Stephen J

2011-01-01

Leaders emerge from leaderless groups as part of a more complex emerging social structure. Several studies have shown that the emerging structure is aptly described by a swallowtail catastrophe model where the control parameters differ depending on whether creative problem solving, production, coordination-intensive, or emergency management groups are involved. The present study explored creative problem solving further where the participants were engaged in real-world tasks extending over several months rather than short laboratory tasks. Participants were engineering students who were organized into groups of to people who designed, built, and tested a prototype product that would solve a real-world problem. At the th week of work they completed a questionnaire indicating who was most like the leader of their group, second most like the leader, along with other questions about individuals' contributions to the group process. Results showed that the swallowtail model (R = .) exhibited a strong advantage over the linear alternative model (R = .) for predicting leadership emergence. The three control variables were control of the task, creative contributions to the group's work, and facilitating the creative contributions of others.

Extending statistical boosting. An overview of recent methodological developments.

Science.gov (United States)

Mayr, A; Binder, H; Gefeller, O; Schmid, M

2014-01-01

Boosting algorithms to simultaneously estimate and select predictor effects in statistical models have gained substantial interest during the last decade. This review highlights recent methodological developments regarding boosting algorithms for statistical modelling especially focusing on topics relevant for biomedical research. We suggest a unified framework for gradient boosting and likelihood-based boosting (statistical boosting) which have been addressed separately in the literature up to now. The methodological developments on statistical boosting during the last ten years can be grouped into three different lines of research: i) efforts to ensure variable selection leading to sparser models, ii) developments regarding different types of predictor effects and how to choose them, iii) approaches to extend the statistical boosting framework to new regression settings. Statistical boosting algorithms have been adapted to carry out unbiased variable selection and automated model choice during the fitting process and can nowadays be applied in almost any regression setting in combination with a large amount of different types of predictor effects.

Isolated Full Bridge Boost DC-DC Converter Designed for Bidirectional Operation of Fuel Cells/Electrolyzer Cells in Grid-Tie Applications

DEFF Research Database (Denmark)

Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

2013-01-01

Energy production from renewable energy sources is continuously varying, for this reason energy storage is becoming more and more important as the percentage of green energy increases. Newly developed fuel cells can operate in reverse mode as electrolyzer cells; therefore, they are becoming...... current. Dc-dc converter efficiency plays a fundamental role in the overall system efficiency since processed energy is always flowing through the converter; for this reason, loss analysis and optimization are a key component of the converter design. The paper presents an isolated full bridge boost dc...

Closed Loop Fuzzy Logic Controlled PV Based Cascaded Boost Five-Level Inverter System

Science.gov (United States)

Revana, Guruswamy; Kota, Venkata Reddy

2018-04-01

Recent developments in intelligent control methods and power electronics have produced PV based DC to AC converters related to AC drives. Cascaded boost converter and inverter find their way in interconnecting PV and Induction Motor. This paper deals with digital simulation and implementation of closed loop controlled five-level inverter based Photo-Voltaic (PV) system. The objective of this work is to reduce the harmonics using Multi Level Inverter based system. The DC output from the PV panel is boosted using cascaded-boost-converters. The DC output of these cascaded boost converters is applied to the bridges of the cascaded inverter. The AC output voltage is obtained by the series cascading of the output voltage of the two inverters. The investigations are done with Induction motor load. Cascaded boost-converter is proposed in the present work to produce the required DC Voltage at the input of the bridge inverter. A simple FLC is applied to CBFLIIM system. The FLC is proposed to reduce the steady state error. The simulation results are compared with the hardware results. The results of the comparison are made to show the improvement in dynamic response in terms of settling time and steady state error. Design procedure and control strategy are presented in detail.

OKVAR-Boost: a novel boosting algorithm to infer nonlinear dynamics and interactions in gene regulatory networks.

Science.gov (United States)

Lim, Néhémy; Senbabaoglu, Yasin; Michailidis, George; d'Alché-Buc, Florence

2013-06-01

Reverse engineering of gene regulatory networks remains a central challenge in computational systems biology, despite recent advances facilitated by benchmark in silico challenges that have aided in calibrating their performance. A number of approaches using either perturbation (knock-out) or wild-type time-series data have appeared in the literature addressing this problem, with the latter using linear temporal models. Nonlinear dynamical models are particularly appropriate for this inference task, given the generation mechanism of the time-series data. In this study, we introduce a novel nonlinear autoregressive model based on operator-valued kernels that simultaneously learns the model parameters, as well as the network structure. A flexible boosting algorithm (OKVAR-Boost) that shares features from L2-boosting and randomization-based algorithms is developed to perform the tasks of parameter learning and network inference for the proposed model. Specifically, at each boosting iteration, a regularized Operator-valued Kernel-based Vector AutoRegressive model (OKVAR) is trained on a random subnetwork. The final model consists of an ensemble of such models. The empirical estimation of the ensemble model's Jacobian matrix provides an estimation of the network structure. The performance of the proposed algorithm is first evaluated on a number of benchmark datasets from the DREAM3 challenge and then on real datasets related to the In vivo Reverse-Engineering and Modeling Assessment (IRMA) and T-cell networks. The high-quality results obtained strongly indicate that it outperforms existing approaches. The OKVAR-Boost Matlab code is available as the archive: http://amis-group.fr/sourcecode-okvar-boost/OKVARBoost-v1.0.zip. Supplementary data are available at Bioinformatics online.

Boosting Learning Algorithm for Stock Price Forecasting

Science.gov (United States)

Wang, Chengzhang; Bai, Xiaoming

2018-03-01

To tackle complexity and uncertainty of stock market behavior, more studies have introduced machine learning algorithms to forecast stock price. ANN (artificial neural network) is one of the most successful and promising applications. We propose a boosting-ANN model in this paper to predict the stock close price. On the basis of boosting theory, multiple weak predicting machines, i.e. ANNs, are assembled to build a stronger predictor, i.e. boosting-ANN model. New error criteria of the weak studying machine and rules of weights updating are adopted in this study. We select technical factors from financial markets as forecasting input variables. Final results demonstrate the boosting-ANN model works better than other ones for stock price forecasting.

Values-led Participatory Design - Mediating the Emergence of Values

DEFF Research Database (Denmark)

Iversen, Ole Sejer; Leong, Tuck Wah

2012-01-01

There is a growing interest in values-led inquiries within participatory design. One approach argues that working with values is a recursive 3-phase process that supports the emergence, development and grounding of values. In this paper we focus solely upon the emergence phase, proposing...... an approach that can support the emergence of values during the initial phase of a values-led inquiry. To illustrate this approach and to ground our discussion, we draw from a recent participatory design case where we were engaged in the design of digital technology to support the experiences of young adults...... with severe intellectual disabilities, in an art museum. By describing how we establish, negotiate and the debrief values during this initial phase of a values-led inquiry. By foregrounding both explicit and implicit mediation in the PD process we show how a theoretical understanding of mediation can...

Detecting Boosted Dark Matter from the Sun with Large Volume Neutrino Detectors

Energy Technology Data Exchange (ETDEWEB)

Berger, Joshua; /SLAC; Cui, Yanou; /Perimeter Inst. Theor. Phys.; Zhao, Yue; /Stanford U., ITP /Stanford U., Phys. Dept.

2015-04-02

We study novel scenarios where thermal dark matter (DM) can be efficiently captured in the Sun and annihilate into boosted dark matter. In models with semi-annihilating DM, where DM has a non-minimal stabilization symmetry, or in models with a multi-component DM sector, annihilations of DM can give rise to stable dark sector particles with moderate Lorentz boosts. We investigate both of these possibilities, presenting concrete models as proofs of concept. Both scenarios can yield viable thermal relic DM with masses O(1)-O(100) GeV. Taking advantage of the energetic proton recoils that arise when the boosted DM scatters off matter, we propose a detection strategy which uses large volume terrestrial detectors, such as those designed to detect neutrinos or proton decays. In particular, we propose a search for proton tracks pointing towards the Sun. We focus on signals at Cherenkov-radiation-based detectors such as Super-Kamiokande (SK) and its upgrade Hyper-Kamiokande (HK). We find that with spin-dependent scattering as the dominant DM-nucleus interaction at low energies, boosted DM can leave detectable signals at SK or HK, with sensitivity comparable to DM direct detection experiments while being consistent with current constraints. Our study provides a new search path for DM sectors with non-minimal structure.

A Three-Phase Boost DC-AC Converter | Odeh | Nigerian Journal of ...

African Journals Online (AJOL)

Sliding mode controllers are designed to perform a robust control for the three boost dc-dc converters. Computer simulations and spectral analysis demonstrate the feasibility of the proposed three-phase inverter. The inverter is intended to be used in three-phase electric drives and uninterruptible power supply (UPS) ...

Reducing maternal mortality in conflict areas: Surgical-anesthetic experience in Boost Hospital - Afghanistan

OpenAIRE

Izquierdo, Gilda; Trelles, Miguel; Khan, Nasrullah

2016-01-01

Introduction: Helmand province, whose capital is Lashkar-Gah, is one of the most volatile provinces affected by the conflict in Afghanistan. Doctors without Borders began to work in Boost Hospital in 2009. Method: Retrospective review of surgical procedures at the Doctors without Borders Operational Center in Brussels, February 11, 2010 to September 30, 2012. Results: 5719 surgeries were performed on 4334 patients. 47% were emergency interventions and 75% were first interventions. 39.7% (n = ...

Emerging Dynamic Design Techniques for Mechanical and ...

Indian Academy of Sciences (India)

Emerging Dynamic Design Techniques for Mechanical ... through this school to bring about an awareness of the state-of-art of the software and ... those mentioned above, cannot be ensured on the basis of approaches involving numerical.

Advanced Airfoils Boost Helicopter Performance

Science.gov (United States)

2007-01-01

Carson Helicopters Inc. licensed the Langley RC4 series of airfoils in 1993 to develop a replacement main rotor blade for their Sikorsky S-61 helicopters. The company's fleet of S-61 helicopters has been rebuilt to include Langley's patented airfoil design, and the helicopters are now able to carry heavier loads and fly faster and farther, and the main rotor blades have twice the previous service life. In aerial firefighting, the performance-boosting airfoils have helped the U.S. Department of Agriculture's Forest Service control the spread of wildfires. In 2003, Carson Helicopters signed a contract with Ducommun AeroStructures Inc., to manufacture the composite blades for Carson Helicopters to sell

Mixed methods research: a design for emergency care research?

Science.gov (United States)

Cooper, Simon; Porter, Jo; Endacott, Ruth

2011-08-01

This paper follows previous publications on generic qualitative approaches, qualitative designs and action research in emergency care by this group of authors. Contemporary views on mixed methods approaches are considered, with a particular focus on the design choice and the amalgamation of qualitative and quantitative data emphasising the timing of data collection for each approach, their relative 'weight' and how they will be mixed. Mixed methods studies in emergency care are reviewed before the variety of methodological approaches and best practice considerations are presented. The use of mixed methods in clinical studies is increasing, aiming to answer questions such as 'how many' and 'why' in the same study, and as such are an important and useful approach to many key questions in emergency care.

Identifying and Managing Engineering Design Requirements for Emerging Markets

DEFF Research Database (Denmark)

Li, Xuemeng

, especially for those companies originally from developed markets, to acquire an in-depth understanding of particular design requirements in emerging markets in order to adapt both company products and approaches in such contexts. Prior studies on the identification and management of design requirements have...... predominantly been conducted in the context of developed countries and relatively affluent markets. Emerging markets are distinct from developed markets in terms of numerous contextual factors, e.g., regulatory environments and competitive landscapes. These factors influence the requirement identification...... attention. There is a need for an overview of different perspectives in requirement identification for manufacturing companies and their corresponding assessments in the context of emerging markets. Therefore, this research project is motivated to 1) investigate the process of identifying and managing...

Boosting long-term memory via wakeful rest: intentional rehearsal is not necessary, consolidation is sufficient.

Science.gov (United States)

Dewar, Michaela; Alber, Jessica; Cowan, Nelson; Della Sala, Sergio

2014-01-01

People perform better on tests of delayed free recall if learning is followed immediately by a short wakeful rest than by a short period of sensory stimulation. Animal and human work suggests that wakeful resting provides optimal conditions for the consolidation of recently acquired memories. However, an alternative account cannot be ruled out, namely that wakeful resting provides optimal conditions for intentional rehearsal of recently acquired memories, thus driving superior memory. Here we utilised non-recallable words to examine whether wakeful rest boosts long-term memory, even when new memories could not be rehearsed intentionally during the wakeful rest delay. The probing of non-recallable words requires a recognition paradigm. Therefore, we first established, via Experiment 1, that the rest-induced boost in memory observed via free recall can be replicated in a recognition paradigm, using concrete nouns. In Experiment 2, participants heard 30 non-recallable non-words, presented as 'foreign names in a bridge club abroad' and then either rested wakefully or played a visual spot-the-difference game for 10 minutes. Retention was probed via recognition at two time points, 15 minutes and 7 days after presentation. As in Experiment 1, wakeful rest boosted recognition significantly, and this boost was maintained for at least 7 days. Our results indicate that the enhancement of memory via wakeful rest is not dependent upon intentional rehearsal of learned material during the rest period. We thus conclude that consolidation is sufficient for this rest-induced memory boost to emerge. We propose that wakeful resting allows for superior memory consolidation, resulting in stronger and/or more veridical representations of experienced events which can be detected via tests of free recall and recognition.

Exploring memory hierarchy design with emerging memory technologies

CERN Document Server

Sun, Guangyu

2014-01-01

This book equips readers with tools for computer architecture of high performance, low power, and high reliability memory hierarchy in computer systems based on emerging memory technologies, such as STTRAM, PCM, FBDRAM, etc.  The techniques described offer advantages of high density, near-zero static power, and immunity to soft errors, which have the potential of overcoming the “memory wall.”  The authors discuss memory design from various perspectives: emerging memory technologies are employed in the memory hierarchy with novel architecture modification;  hybrid memory structure is introduced to leverage advantages from multiple memory technologies; an analytical model named “Moguls” is introduced to explore quantitatively the optimization design of a memory hierarchy; finally, the vulnerability of the CMPs to radiation-based soft errors is improved by replacing different levels of on-chip memory with STT-RAMs.   ·         Provides a holistic study of using emerging memory technologies i...

Face Alignment Using Boosting and Evolutionary Search

NARCIS (Netherlands)

Zhang, Hua; Liu, Duanduan; Poel, Mannes; Nijholt, Antinus; Zha, H.; Taniguchi, R.-I.; Maybank, S.

2010-01-01

In this paper, we present a face alignment approach using granular features, boosting, and an evolutionary search algorithm. Active Appearance Models (AAM) integrate a shape-texture-combined morphable face model into an efficient fitting strategy, then Boosting Appearance Models (BAM) consider the

Inelastic Boosted Dark Matter at direct detection experiments

Science.gov (United States)

Giudice, Gian F.; Kim, Doojin; Park, Jong-Chul; Shin, Seodong

2018-05-01

We explore a novel class of multi-particle dark sectors, called Inelastic Boosted Dark Matter (iBDM). These models are constructed by combining properties of particles that scatter off matter by making transitions to heavier states (Inelastic Dark Matter) with properties of particles that are produced with a large Lorentz boost in annihilation processes in the galactic halo (Boosted Dark Matter). This combination leads to new signals that can be observed at ordinary direct detection experiments, but require unconventional searches for energetic recoil electrons in coincidence with displaced multi-track events. Related experimental strategies can also be used to probe MeV-range boosted dark matter via their interactions with electrons inside the target material.

Fast neutron boost for the treatment of grade IV astrocytomas

International Nuclear Information System (INIS)

Breteau, N.; Destembert, B.; Favre, A.; Pheline, C.; Schlienger, M.

1989-01-01

A previous study, on grade IV astrocytomas, compared a combination of photons and fast neutron boost to photons only, both treatments being delivered following a concentrated irradiation schedule. A slight improvement in survival was observed after neutron boost for non operated patients, but not for operated patients. Since death was always related to local recurrence and since no complication occurred after neutron boost, the neutron dose was increased from 6 to 7 Gy in January 1985. No improvement in survival was observed for patients treated with neutron boost after complete resection. After subtotal resection, the group that was treated with the higher neutron boost (7 Gy) showed a significant benefit in survival at twelve months. When patients had only a biopsy before irradiation, there was a benefit in survival after neutron boost, but no additional benefit was gained when the size of the neutron boost was increased from 6 to 7 Gy. (orig.) [de

Orthodontics Align Crooked Teeth and Boost Self-Esteem

Science.gov (United States)

... desktop! more... Orthodontics Align Crooked Teeth and Boost Self- esteem Article Chapters Orthodontics Align Crooked Teeth and Boost Self- esteem print full article print this chapter email this ...

Control analysis and experimental verification of a practical dc–dc boost converter

Directory of Open Access Journals (Sweden)

Saswati Swapna Dash

2015-12-01

Full Text Available This paper presents detailed open loop and closed loop analysis on boost dc–dc converter for both voltage mode control and current mode control. Here the boost dc–dc converter is a practical converter considering all possible parasitic elements like ESR and on state voltage drops. The open loop control, closed loop current mode control and voltage mode control are verified. The comparative study of all control techniques is presented. The PI compensator for closed loop current mode control is designed using these classical techniques like root locus technique and bode diagram. The simulation results are validated with the experimental results of voltage mode control for both open loop and closed loop control.

Scenario-based design: a method for connecting information system design with public health operations and emergency management.

Science.gov (United States)

Reeder, Blaine; Turner, Anne M

2011-12-01

Responding to public health emergencies requires rapid and accurate assessment of workforce availability under adverse and changing circumstances. However, public health information systems to support resource management during both routine and emergency operations are currently lacking. We applied scenario-based design as an approach to engage public health practitioners in the creation and validation of an information design to support routine and emergency public health activities. Using semi-structured interviews we identified the information needs and activities of senior public health managers of a large municipal health department during routine and emergency operations. Interview analysis identified 25 information needs for public health operations management. The identified information needs were used in conjunction with scenario-based design to create 25 scenarios of use and a public health manager persona. Scenarios of use and persona were validated and modified based on follow-up surveys with study participants. Scenarios were used to test and gain feedback on a pilot information system. The method of scenario-based design was applied to represent the resource management needs of senior-level public health managers under routine and disaster settings. Scenario-based design can be a useful tool for engaging public health practitioners in the design process and to validate an information system design. Copyright © 2011 Elsevier Inc. All rights reserved.

Boost.Unicode : a Unicode library for C++

OpenAIRE

Wien, Erik; Gigstad, Lars Erik

2005-01-01

The project has resulted in a Unicode string library for C++ that abstracts away the complexity of working with Unicode text. The idea behind the project originated from the Boost community's developer mailings lists, and is developed with inclusion into the Boost library collection in mind.

Inelastic Boosted Dark Matter at direct detection experiments

OpenAIRE

Giudice, Gian F.; Kim, Doojin; Park, Jong-Chul; Shin, Seodong

2018-01-01

We explore a novel class of multi-particle dark sectors, called Inelastic Boosted Dark Matter (iBDM). These models are constructed by combining properties of particles that scatter off matter by making transitions to heavier states (Inelastic Dark Matter) with properties of particles that are produced with a large Lorentz boost in annihilation processes in the galactic halo (Boosted Dark Matter). This combination leads to new signals that can be observed at ordinary direct detection experimen...

Boosted top: experimental tools overview

CERN Document Server

Usai, Emanuele

2015-01-01

An overview of tools and methods for the reconstruction of high-boost top quark decays at the LHC is given in this report. The focus is on hadronic decays, in particular an overview of the current status of top quark taggers in physics analyses is presented. The most widely used jet substructure techniques, normally used in combination with top quark taggers, are reviewed. Special techniques to treat pileup in large cone jets are described, along with a comparison of the performance of several boosted top quark reconstruction techniques.

Modeling and Control of DC/DC Boost Converter using K-Factor Control for MPPT of Solar PV System

DEFF Research Database (Denmark)

Vangari, Adithya; Haribabu, Divyanagalakshmi; Sakamuri, Jayachandra N.

2015-01-01

This paper is focused on the design of a controller for the DC/DC boost converter using K factor control, which is based on modified PI control method, for maximum power point tracking (MPPT) of solar PV system. A mathematical model for boost converter based on small signal averaging approach...... is presented. Design of the passive elements of the boost converter as per the system specifications is also illustrated. The performance of the proposed K factor control method is verified with the simulations for MPPT on solar PV system at different atmospheric conditions. A new circuit based model for solar...... PV array, which includes the effect of solar insolation and temperature on PV array output, for the application in power system transient simulations, is also presented. The performance of the PV array model is verified with simulations at different atmospheric conditions. A 160W PV module from BP...

A PIPO Boost Converter with Low Ripple and Medium Current Application

Science.gov (United States)

Bandri, S.; Sofian, A.; Ismail, F.

2018-04-01

This paper presents a Parallel Input Parallel Output (PIPO) boost converter is proposed to gain power ability of converter, and reduce current inductors. The proposed technique will distribute current for n-parallel inductor and switching component. Four parallel boost converters implement on input voltage 20.5Vdc to generate output voltage 28.8Vdc. The PIPO boost converter applied phase shift pulse width modulation which will compare with conventional PIPO boost converters by using a similar pulse for every switching component. The current ripple reduction shows an advantage PIPO boost converter then conventional boost converter. Varies loads and duty cycle will be simulated and analyzed to verify the performance of PIPO boost converter. Finally, the unbalance of current inductor is able to be verified on four area of duty cycle in less than 0.6.

Concomitant boost radiotherapy for muscle invasive bladder cancer

Energy Technology Data Exchange (ETDEWEB)

Pos, Floris J; Tienhoven, Geertjan van; Hulshof, Maarten C.C.M.; Koedooder, Kees; Gonzalez Gonzalez, Dionisio

2003-07-01

Purpose: To evaluate the feasibility and efficacy of a concomitant partial bladder boost schedule in radiotherapy for invasive bladder cancer, coupling a limited boost volume with shortening of the overall treatment time. Methods and materials: Between 1994 and 1999, 50 patients with a T2-T4 N0M0 transitional cell carcinoma of the bladder received radiotherapy delivered in a short overall treatment time with a concomitant boost technique. With this technique a dose of 40 Gy in 2-Gy fractions was administered to the small pelvis with a concomitant boost limited to the bladder tumor area plus margin of 15 Gy in fractions of 0.75 Gy. The total tumor dose was 55 Gy in 20 fractions in 4 weeks. Toxicity was scored according to EORTC/RTOG toxicity criteria. Results: The feasibility of the treatment was good. Severe acute toxicity {>=}G3 was observed in seven patients (14%). Severe late toxicity {>=}G3 was observed in six patients (13%). Thirty-seven patients (74%) showed a complete and five (10 %) a partial remission after treatment. The actuarial 3-year freedom of local progression was 55%. Conclusion: In external radiotherapy for muscle invasive bladder cancer a concomitant boost technique coupling a partial bladder boost with shortening of the overall treatment time provides a high probability of local control with acceptable toxicity.

Concomitant boost radiotherapy for muscle invasive bladder cancer

International Nuclear Information System (INIS)

Pos, Floris J.; Tienhoven, Geertjan van; Hulshof, Maarten C.C.M.; Koedooder, Kees; Gonzalez Gonzalez, Dionisio

2003-01-01

Purpose: To evaluate the feasibility and efficacy of a concomitant partial bladder boost schedule in radiotherapy for invasive bladder cancer, coupling a limited boost volume with shortening of the overall treatment time. Methods and materials: Between 1994 and 1999, 50 patients with a T2-T4 N0M0 transitional cell carcinoma of the bladder received radiotherapy delivered in a short overall treatment time with a concomitant boost technique. With this technique a dose of 40 Gy in 2-Gy fractions was administered to the small pelvis with a concomitant boost limited to the bladder tumor area plus margin of 15 Gy in fractions of 0.75 Gy. The total tumor dose was 55 Gy in 20 fractions in 4 weeks. Toxicity was scored according to EORTC/RTOG toxicity criteria. Results: The feasibility of the treatment was good. Severe acute toxicity ≥G3 was observed in seven patients (14%). Severe late toxicity ≥G3 was observed in six patients (13%). Thirty-seven patients (74%) showed a complete and five (10 %) a partial remission after treatment. The actuarial 3-year freedom of local progression was 55%. Conclusion: In external radiotherapy for muscle invasive bladder cancer a concomitant boost technique coupling a partial bladder boost with shortening of the overall treatment time provides a high probability of local control with acceptable toxicity

Analisys of Current-Bidirectional Buck-Boost Based Automotive Switch-Mode Audio Amplifier

DEFF Research Database (Denmark)

Bolten Maizonave, Gert; Andersen, Michael A. E.; Kjærgaard, Claus

2011-01-01

The following study was carried out in order to assess quantitatively the performance of the buck-boost converter when used as switch-mode audio amplifier. It comprises of, to begin with, the delimitation of design criteria based on the state-ofthe- art solution, which is based in a differential ...

Holocraneal irradiation with boost integrated simultaneous of oligo metastases using Exa frame and Exa skin with VMAI-IGRT; Irradiacion holocraneal con boost integrado simultaneo de oligometastasis usando Exaframe y Exaskin con VMAT-IGRT

Energy Technology Data Exchange (ETDEWEB)

Velazquez Miranda, S.; Montero Perea, E.; Ortiz Seidel, M.

2013-07-01

The described technique of prophylaxis back hippo-fractionated with simultaneous integrated boost presents advantages in terms of reduction of treatment time total, fast local effect on the oligo metastases and possible prevention of the emergence of new cranial metastasis. The possible impact on long-term survival remains to be determined. In any case, this technique is presented as a valid alternative in terms of clinical outcomes and toxicity to stereotaxic standard treatments. (Author)

Introducing state-trajectory control for the synchronous interleaved boost converter

DEFF Research Database (Denmark)

Peña-Alzola, Rafael; Ksiazek, Peter; Ordonez, Martin

2015-01-01

Synchronous interleaved boost converters (SIBCs) result in lower ripple currents and bidirectional power flow. The boost topology has a non-minimum phase characteristic, producing instability problems when a large bandwidth is required. Linear controllers inherently limit the boost controller...

Prediction of Outcome in Acute Lower Gastrointestinal Bleeding Using Gradient Boosting.

Directory of Open Access Journals (Sweden)

Lakshmana Ayaru

Full Text Available There are no widely used models in clinical care to predict outcome in acute lower gastro-intestinal bleeding (ALGIB. If available these could help triage patients at presentation to appropriate levels of care/intervention and improve medical resource utilisation. We aimed to apply a state-of-the-art machine learning classifier, gradient boosting (GB, to predict outcome in ALGIB using non-endoscopic measurements as predictors.Non-endoscopic variables from patients with ALGIB attending the emergency departments of two teaching hospitals were analysed retrospectively for training/internal validation (n=170 and external validation (n=130 of the GB model. The performance of the GB algorithm in predicting recurrent bleeding, clinical intervention and severe bleeding was compared to a multiple logic regression (MLR model and two published MLR-based prediction algorithms (BLEED and Strate prediction rule.The GB algorithm had the best negative predictive values for the chosen outcomes (>88%. On internal validation the accuracy of the GB algorithm for predicting recurrent bleeding, therapeutic intervention and severe bleeding were (88%, 88% and 78% respectively and superior to the BLEED classification (64%, 68% and 63%, Strate prediction rule (78%, 78%, 67% and conventional MLR (74%, 74% 62%. On external validation the accuracy was similar to conventional MLR for recurrent bleeding (88% vs. 83% and therapeutic intervention (91% vs. 87% but superior for severe bleeding (83% vs. 71%.The gradient boosting algorithm accurately predicts outcome in patients with acute lower gastrointestinal bleeding and outperforms multiple logistic regression based models. These may be useful for risk stratification of patients on presentation to the emergency department.

4 Types of Foods that Boost Your Memory

Science.gov (United States)

... 4 Types of Foods to Help Boost Your Memory By Marisa Moore, MBA, RDN, LD Published November ... in brain health. The best menu for boosting memory and brain function encourages good blood flow to ...

Boosting long-term memory via wakeful rest: intentional rehearsal is not necessary, consolidation is sufficient.

Directory of Open Access Journals (Sweden)

Michaela Dewar

Full Text Available People perform better on tests of delayed free recall if learning is followed immediately by a short wakeful rest than by a short period of sensory stimulation. Animal and human work suggests that wakeful resting provides optimal conditions for the consolidation of recently acquired memories. However, an alternative account cannot be ruled out, namely that wakeful resting provides optimal conditions for intentional rehearsal of recently acquired memories, thus driving superior memory. Here we utilised non-recallable words to examine whether wakeful rest boosts long-term memory, even when new memories could not be rehearsed intentionally during the wakeful rest delay. The probing of non-recallable words requires a recognition paradigm. Therefore, we first established, via Experiment 1, that the rest-induced boost in memory observed via free recall can be replicated in a recognition paradigm, using concrete nouns. In Experiment 2, participants heard 30 non-recallable non-words, presented as 'foreign names in a bridge club abroad' and then either rested wakefully or played a visual spot-the-difference game for 10 minutes. Retention was probed via recognition at two time points, 15 minutes and 7 days after presentation. As in Experiment 1, wakeful rest boosted recognition significantly, and this boost was maintained for at least 7 days. Our results indicate that the enhancement of memory via wakeful rest is not dependent upon intentional rehearsal of learned material during the rest period. We thus conclude that consolidation is sufficient for this rest-induced memory boost to emerge. We propose that wakeful resting allows for superior memory consolidation, resulting in stronger and/or more veridical representations of experienced events which can be detected via tests of free recall and recognition.

Emergency procedures beyond design basis ''Feed and Bleed''

International Nuclear Information System (INIS)

Dominguez Bautista, M.T.; Campuzano Pena, F.

1994-01-01

The incorporation of Beyond-Design-Basis Emergency Procedures, also called the Emergency Manual or Severe Accident Manual, has been an important step forward in nuclear power plant safety. These procedures cover situations in which the deterministic criteria used in plant design have been contravened. In such situations new accident scenarios, unforeseen system actions or a combination of both, need to be considered. Establishing these procedures is actually the last in a sequence of activities the sequence includes definition of scenarios, study of their phenomena, analysis of optional system actions, verification of their effectiveness and finally, implementation of the procedure. The systematization of these new strategies is supported by the results of the probabilistic analyses which serve in this case to pinpoint the objectives of these strategies. This paper describes the application of this methodology in the definition of a procedure for heat sink recovery on the secondary side (feed and bleed) if this has been totally or partially lost in a beyond-design-basis event. (Author)

Diode-Assisted Buck-Boost Current Source Inverters

DEFF Research Database (Denmark)

Gao, F.; Cai, Liang; Loh, P.C.

2007-01-01

This paper presents a couple of novel current source inverters (CSIs) with the enhanced current buckboost capability. With the unique diode-inductor network added between current source inverter circuitry and current boost elements, the proposed buck-boost current source inverters demonstrate...... uninfluenced. Lastly, all theoretical findings were verified experimentally using constructed laboratory prototypes....

Design principles for global commons: Natural resources and emerging technologies

Directory of Open Access Journals (Sweden)

Paul C. Stern

2011-09-01

Full Text Available Ostrom’s design principles for managing common pool resources were developed largely by examining local commons involving natural resources. This paper enumerates several key characteristics that distinguish such commons from more complex commons involving global resources and the risks of emerging technologies. It considers the degree to which the design principles transfer to those commons and concludes that although they have considerable external validity, the list needs some modification and elaboration to apply to global resources and risk commons. A list of design principles is offered for global resource commons and the risks of emerging technologies. Applying Ostrom’s approach to global resources and emerging technologies can improve understanding and expand the solution set for these problems from international treaties, top-down national regulation, and interventions in market pricing systems to include non-governmental institutions that embody principles of self-governance.

Emerging Assumptions About Organization Design, Knowledge And Action

Directory of Open Access Journals (Sweden)

Alan Meyer

2013-12-01

Full Text Available Participants in the Organizational Design Community’s 2013 Annual Conference faced the challenge of “making organization design knowledge actionable.”  This essay summarizes the opinions and insights participants shared during the conference.  I reflect on these ideas, connect them to recent scholarly thinking about organization design, and conclude that seeking to make design knowledge actionable is nudging the community away from an assumption set based upon linearity and equilibrium, and toward a new set of assumptions based on emergence, self-organization, and non-linearity.

Primary Paralleled Isolated Boost Converter with Extended Operating Voltage Range

DEFF Research Database (Denmark)

Hernandez Botella, Juan Carlos; Sen, Gökhan; Mira Albert, Maria del Carmen

2012-01-01

Applications requiring wide input and output voltage range cannot often be satisfied by using buck or boost derived topologies. Primary paralleled isolated boost converter (PPIBC) [1]-[2] is a high efficiency boost derived topology. This paper proposes a new operation mode for extending the input...

Symmetry boost of the fidelity of Shor factoring

Science.gov (United States)

Nam, Y. S.; Blümel, R.

2018-05-01

In Shor's algorithm quantum subroutines occur with the structure F U F-1 , where F is a unitary transform and U is performing a quantum computation. Examples are quantum adders and subunits of quantum modulo adders. In this paper we show, both analytically and numerically, that if, in analogy to spin echoes, F and F-1 can be implemented symmetrically when executing Shor's algorithm on actual, imperfect quantum hardware, such that F and F-1 have the same hardware errors, a symmetry boost in the fidelity of the combined F U F-1 quantum operation results when compared to the case in which the errors in F and F-1 are independently random. Running the complete gate-by-gate implemented Shor algorithm, we show that the symmetry-induced fidelity boost can be as large as a factor 4. While most of our analytical and numerical results concern the case of over- and under-rotation of controlled rotation gates, in the numerically accessible case of Shor's algorithm with a small number of qubits, we show explicitly that the symmetry boost is robust with respect to more general types of errors. While, expectedly, additional error types reduce the symmetry boost, we show explicitly, by implementing general off-diagonal SU (N ) errors (N =2 ,4 ,8 ), that the boost factor scales like a Lorentzian in δ /σ , where σ and δ are the error strengths of the diagonal over- and underrotation errors and the off-diagonal SU (N ) errors, respectively. The Lorentzian shape also shows that, while the boost factor may become small with increasing δ , it declines slowly (essentially like a power law) and is never completely erased. We also investigate the effect of diagonal nonunitary errors, which, in analogy to unitary errors, reduce but never erase the symmetry boost. Going beyond the case of small quantum processors, we present analytical scaling results that show that the symmetry boost persists in the practically interesting case of a large number of qubits. We illustrate this result

An Update on Statistical Boosting in Biomedicine.

Science.gov (United States)

Mayr, Andreas; Hofner, Benjamin; Waldmann, Elisabeth; Hepp, Tobias; Meyer, Sebastian; Gefeller, Olaf

2017-01-01

Statistical boosting algorithms have triggered a lot of research during the last decade. They combine a powerful machine learning approach with classical statistical modelling, offering various practical advantages like automated variable selection and implicit regularization of effect estimates. They are extremely flexible, as the underlying base-learners (regression functions defining the type of effect for the explanatory variables) can be combined with any kind of loss function (target function to be optimized, defining the type of regression setting). In this review article, we highlight the most recent methodological developments on statistical boosting regarding variable selection, functional regression, and advanced time-to-event modelling. Additionally, we provide a short overview on relevant applications of statistical boosting in biomedicine.

Design evaluation of emergency core cooling systems using Axiomatic Design

Energy Technology Data Exchange (ETDEWEB)

Heo, Gyunyoung [Massachusetts Institute of Technology, Department of Mechanical Engineering, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States)]. E-mail: gheo@mit.edu; Lee, Song Kyu [Korea Advanced Institute of Science and Technology, Department of Nuclear and Quantum Engineering, 373-1 Guseong-dong, Yuseong-gu, Daejeon (Korea, Republic of)

2007-01-15

In designing nuclear power plants (NPPs), the evaluation of safety is one of the important issues. As a measure for evaluating safety, this paper proposes a methodology to examine the design process of emergency core cooling systems (ECCSs) in NPPs using Axiomatic Design (AD). This is particularly important for identifying vulnerabilities and creating solutions. Korean Advanced Power Reactor 1400 MWe (APR1400) adopted the ECCS, which was improved to meet the stronger safety regulations than that of the current Optimized Power Reactor 1000 MWe (OPR1000). To improve the performance and safety of the ECCS, the various design strategies such as independency or redundancy were implemented, and their effectiveness was confirmed by calculating core damage frequency. We suggest an alternative viewpoint of evaluating the deployment of design strategies in terms of AD methodology. AD suggests two design principles and the visualization tools for organizing design process. The important benefit of AD is that it is capable of providing suitable priorities for deploying design strategies. The reverse engineering driven by AD has been able to show that the design process of the ECCS of APR1400 was improved in comparison to that of OPR1000 from the viewpoint of the coordination of design strategies.

Emergent collaboration infrastructures technology design for inter-organizational crisis management

CERN Document Server

Reuter, Christian

2015-01-01

​Using the domain of crisis management, Christian Reuter explores challenges and opportunities for technology design in emergent environments. He therefore empirically analyzes collaborative work in inter-organizational crisis - such as the police, fire departments, energy network operators and citizens - in order to identify collaboration practices that reveal work infrastructure limitations. He also designs, implements and evaluates novel concepts and ICT artifacts towards the support of emergent collaboration. Besides the discovery of potential organizational effects on the ability to deal

Internationalization of Boost Juice to Malaysia

OpenAIRE

Jane L. Menzies; Stuart C. Orr

2014-01-01

This case describes the process that the Australian juice retail chain, Boost Juice, has used to internationalize to Malaysia. The main objective of this case is to demonstrate good practice in regard to internationalization. The case provides the background of the juice bar industry in Malaysia and determines that it is an attractive market for new start-up juice bars. An analysis of Boost Juice's capability determined that the company utilized the skills of its staff, product innovations, b...

An Emerging Learning Design for Student-Generated "iVideos"

Science.gov (United States)

Kearney, Matthew; Jones, Glynis; Roberts, Lynn

2012-01-01

This paper describes an emerging learning design for a popular genre of learner-generated video projects: "Ideas Videos" or "iVideos." These advocacy-style videos are short, two-minute, digital videos designed "to evoke powerful experiences about educative ideas" (Wong, Mishra, Koehler & Siebenthal, 2007, p1). We…

Model Design on Emergency Power Supply of Electric Vehicle

Directory of Open Access Journals (Sweden)

Yuanliang Zhao

2017-01-01

Full Text Available According to the mobile storage characteristic of electric vehicles, an emergency power supply model about the electric vehicles is presented through analyzing its storage characteristic. The model can ensure important consumer loss minimization during power failure or emergency and can make electric vehicles cost minimization about running, scheduling, and vindicating. In view of the random dispersion feature in one area, an emergency power supply scheme using the electric vehicles is designed based on the K-means algorithm. The purpose is to improve the electric vehicles initiative gathering ability and reduce the electric vehicles gathering time. The study can reduce the number of other emergency power supply equipment and improve the urban electricity reliability.

Radiographer-led breast boost localisation – A service evaluation study

International Nuclear Information System (INIS)

Smith, S.; Comins, C.

2015-01-01

A radiation boost to the tumour bed as part of breast conserving therapy reduces the rate of local recurrence. Radiographer-led planning for tangential field radiotherapy has been the practice at our centre since 2007. The transition from conventional simulation to computed tomography (CT) and virtual simulation enhanced the radiographer's role in the breast planning process. Electron boost mark ups continued to be marked up freehand by doctors using available imaging to determine tumour bed. The paper reports on a service evaluation undertaken to establish a change in practice for electron breast boosts to be simulated using the virtual simulator by suitably trained radiographers. The retrospective simulation of ten patients confirmed the consistency of radiographer tumour bed localisation, followed by the prospective simulation of ten patients' boost fields. The introduction of a radiographer-led planning breast boost service has given greater autonomy and job satisfaction to individuals as well as resulting in a cost effective use of available resources. - Highlights: • A service evaluation study was undertaken to train a radiographer to perform breast boost planning. • Retrospective breast boost planning established proposed technique was workable. • Prospective planning by radiographer proved their competence. • Introduction of new technique provided job satisfaction and service improvement

An Update on Statistical Boosting in Biomedicine

Directory of Open Access Journals (Sweden)

Andreas Mayr

2017-01-01

Full Text Available Statistical boosting algorithms have triggered a lot of research during the last decade. They combine a powerful machine learning approach with classical statistical modelling, offering various practical advantages like automated variable selection and implicit regularization of effect estimates. They are extremely flexible, as the underlying base-learners (regression functions defining the type of effect for the explanatory variables can be combined with any kind of loss function (target function to be optimized, defining the type of regression setting. In this review article, we highlight the most recent methodological developments on statistical boosting regarding variable selection, functional regression, and advanced time-to-event modelling. Additionally, we provide a short overview on relevant applications of statistical boosting in biomedicine.

Boosted jets

International Nuclear Information System (INIS)

Juknevich, J.

2014-01-01

We present a study of the substructure of jets high transverse momentum at hadron colliders. A template method is introduced to distinguish heavy jets by comparing their energy distributions to the distributions of a set of templates which describe the kinematical information from signal or background. As an application, a search for a boosted Higgs boson decaying into bottom quarks in association with a leptonically decaying W boson is presented as well. (author)

Three-level boost converter with zero voltage transition

Directory of Open Access Journals (Sweden)

Kuo-Ing Hwu

2017-06-01

Full Text Available As compared with the traditional boost converter, the three-level boost converter possesses several advantages, such as lower switch voltage stresses and lower inductor current ripple. To improve the efficiency, this paper proposes a zero voltage transition (ZVT three-level boost converter. With the proposed ZVT circuit, the switches can achieve soft switching. Moreover, by using the voltage balance control, the output voltage can be equally across the output capacitors. In this study, the effectiveness of the proposed topology is verified by the experimental results based on the field-programmable gate array control.

Improved Stereo Matching With Boosting Method

Directory of Open Access Journals (Sweden)

Shiny B

2015-06-01

Full Text Available Abstract This paper presents an approach based on classification for improving the accuracy of stereo matching methods. We propose this method for occlusion handling. This work employs classification of pixels for finding the erroneous disparity values. Due to the wide applications of disparity map in 3D television medical imaging etc the accuracy of disparity map has high significance. An initial disparity map is obtained using local or global stereo matching methods from the input stereo image pair. The various features for classification are computed from the input stereo image pair and the obtained disparity map. Then the computed feature vector is used for classification of pixels by using GentleBoost as the classification method. The erroneous disparity values in the disparity map found by classification are corrected through a completion stage or filling stage. A performance evaluation of stereo matching using AdaBoostM1 RUSBoost Neural networks and GentleBoost is performed.

Load estimator-based hybrid controller design for two-interleaved boost converter dedicated to renewable energy and automotive applications.

Science.gov (United States)

Bougrine, Mohamed; Benmiloud, Mohammed; Benalia, Atallah; Delaleau, Emmanuel; Benbouzid, Mohamed

2017-01-01

This paper is devoted to the development of a hybrid controller for a two-interleaved boost converter dedicated to renewable energy and automotive applications. The control requirements, resumed in fast transient and low input current ripple, are formulated as a problem of fast stabilization of a predefined optimal limit cycle, and solved using hybrid automaton formalism. In addition, a real time estimation of the load is developed using an algebraic approach for online adjustment of the hybrid controller. Mathematical proofs are provided with simulations to illustrate the effectiveness and the robustness of the proposed controller despite different disturbances. Furthermore, a fuel cell system supplying a resistive load through a two-interleaved boost converter is also highlighted. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Help Me Please!: Designing and Developing Application for Emergencies

Science.gov (United States)

Hong, Ng Ken; Hafit, Hanayanti; Wahid, Norfaradilla; Kasim, Shahreen; Yusof, Munirah Mohd

2017-08-01

Help Me Please! Application is an android platform emergency button application that is designed to transmit emergency messages to target receivers with real time information. The purpose of developing this application is to help people to notify any emergency circumstances via Short Message Service (SMS) in android platform. The application will receive the current location from Global Positioning System (GPS), will obtain the current time from the mobile device and send this information to the receivers when user presses the emergency button. Simultaneously, the application will keep sending the emergency alerts to receivers and will update to database based on the time interval set by user until user stop the function. Object-oriented Software Development model is employed to guide the development of this application with the knowledge of Java language and Android Studio. In conclusion, this application plays an important role in rescuing process when emergency circumstances happen. The rescue process will become more effective by notifying the emergency circumstances and send the current location of user to others in the early hours.

Boosted beta regression.

Directory of Open Access Journals (Sweden)

Matthias Schmid

Full Text Available Regression analysis with a bounded outcome is a common problem in applied statistics. Typical examples include regression models for percentage outcomes and the analysis of ratings that are measured on a bounded scale. In this paper, we consider beta regression, which is a generalization of logit models to situations where the response is continuous on the interval (0,1. Consequently, beta regression is a convenient tool for analyzing percentage responses. The classical approach to fit a beta regression model is to use maximum likelihood estimation with subsequent AIC-based variable selection. As an alternative to this established - yet unstable - approach, we propose a new estimation technique called boosted beta regression. With boosted beta regression estimation and variable selection can be carried out simultaneously in a highly efficient way. Additionally, both the mean and the variance of a percentage response can be modeled using flexible nonlinear covariate effects. As a consequence, the new method accounts for common problems such as overdispersion and non-binomial variance structures.

Teaching Design of Emerging Embodied Technologies

DEFF Research Database (Denmark)

Majgaard, Gunver

2014-01-01

How does design of emerging embodied technologies enrich the HCI learning processes? We introduce a model for embodied interaction and use it in the development of a painting app for children, based on the motion sensor Asus Xtion Pro (similar to Kinect). The development of the app was part....... Subsequently, we introduce a physical-digital toolbox, illustrating the span of parameters within the model for embodied interaction: Robot Technology, Tangibles, Wearables, Interactive Surroundings, and Bigger Objects....

CyberKnife Boost for Patients with Cervical Cancer Unable to Undergo Brachytherapy

International Nuclear Information System (INIS)

Haas, Jonathan Andrew; Witten, Matthew R.; Clancey, Owen; Episcopia, Karen; Accordino, Diane; Chalas, Eva

2012-01-01

Standard radiation therapy for patients undergoing primary chemosensitized radiation for carcinomas of the cervix usually consists of external beam radiation followed by an intracavitary brachytherapy boost. On occasion, the brachytherapy boost cannot be performed due to unfavorable anatomy or because of coexisting medical conditions. We examined the safety and efficacy of using CyberKnife stereotactic body radiotherapy (SBRT) as a boost to the cervix after external beam radiation in those patients unable to have brachytherapy to give a more effective dose to the cervix than with conventional external beam radiation alone. Six consecutive patients with anatomic or medical conditions precluding a tandem and ovoid boost were treated with combined external beam radiation and CyberKnife boost to the cervix. Five patients received 45 Gy to the pelvis with serial intensity-modulated radiation therapy boost to the uterus and cervix to a dose of 61.2 Gy. These five patients received an SBRT boost to the cervix to a dose of 20 Gy in five fractions of 4 Gy each. One patient was treated to the pelvis to a dose of 45 Gy with an external beam boost to the uterus and cervix to a dose of 50.4 Gy. This patient received an SBRT boost to the cervix to a dose of 19.5 Gy in three fractions of 6.5 Gy. Five percent volumes of the bladder and rectum were kept to ≤75 Gy in all patients (i.e., V75 Gy ≤ 5%). All of the patients remain locally controlled with no evidence of disease following treatment. Grade 1 diarrhea occurred in 4/6 patients during the conventional external beam radiation. There has been no grade 3 or 4 rectal or bladder toxicity. There were no toxicities observed following SBRT boost. At a median follow-up of 14 months, CyberKnife radiosurgical boost is well tolerated and efficacious in providing a boost to patients with cervix cancer who are unable to undergo brachytherapy boost. Further follow-up is required to see if these results remain durable.

Evaluation of Arm Processor-based Bionic Intelligent Controller for a Buck-boost Converte

OpenAIRE

M.V. Mini; L. Padma Suresh

2015-01-01

This study focuses on performance-comparison of different tuning methods for a PI controller applied to a buck-boost converter. Comparison between the controllers is made by analysis of design methodology implementation issues and empirically measured performance. Design of PI controller is based on frequency response of the converter. The optimization of PI controller is based on ant colony algorithm. Experimental results show that, tuning the PI controller using ACO algorithm gave better pe...

Sequentially delivered boost plans are superior to simultaneously delivered plans in head and neck cancer when the boost volume is located further away from the parotid glands

International Nuclear Information System (INIS)

Lamers-Kuijper, Emmy; Heemsbergen, Wilma; Mourik, Anke van; Rasch, Coen

2011-01-01

Purpose: To find parameters that predict which head and neck patients benefit from a sequentially delivered boost treatment plan compared to a simultaneously delivered plan, with the aim to spare the salivary glands. Methods and materials: We evaluated 50 recently treated head and neck cancer patients. Apart from the clinical plan with a sequentially (SEQ) given boost using an Intensity Modulated Radiotherapy Technique (IMRT), a simultaneous integrated boost (SIB) technique plan was constructed with the same beam set-up. The mean dose to the parotid glands was calculated and compared. The elective nodal areas were bilateral in all cases, with a boost on either one side or both sides of the neck. Results: When the parotid gland volume and the Planning Target Volume (PTV) for the boost overlap there is on average a lower dose to the parotid gland with a SIB technique (-1.2 Gy), which is, however, not significant (p = 0.08). For all parotid glands with no boost PTV overlap, there is a benefit from a SEQ technique compared to a SIB technique for the gland evaluated (on average a 2.5 Gy lower dose to the parotid gland, p < 0.001). When the distance between gland and PTV is 0-1 cm, this difference is on average 0.8 Gy, for 1-2 cm distance 2.9 Gy and for glands with a distance greater than 2 cm, 3.3 Gy. When the lymph nodes on the evaluated side are also included in the boost PTV, however, this relationship between the distance and the gain of a SEQ seems less clear. Conclusions: A sequentially delivered boost technique results in a better treatment plan for most cases, compared to a simultaneous integrated boost IMRT technique, if the boost PTV is more than 1 cm away from at least one parotid gland.

Clustering Using Boosted Constrained k-Means Algorithm

Directory of Open Access Journals (Sweden)

Masayuki Okabe

2018-03-01

Full Text Available This article proposes a constrained clustering algorithm with competitive performance and less computation time to the state-of-the-art methods, which consists of a constrained k-means algorithm enhanced by the boosting principle. Constrained k-means clustering using constraints as background knowledge, although easy to implement and quick, has insufficient performance compared with metric learning-based methods. Since it simply adds a function into the data assignment process of the k-means algorithm to check for constraint violations, it often exploits only a small number of constraints. Metric learning-based methods, which exploit constraints to create a new metric for data similarity, have shown promising results although the methods proposed so far are often slow depending on the amount of data or number of feature dimensions. We present a method that exploits the advantages of the constrained k-means and metric learning approaches. It incorporates a mechanism for accepting constraint priorities and a metric learning framework based on the boosting principle into a constrained k-means algorithm. In the framework, a metric is learned in the form of a kernel matrix that integrates weak cluster hypotheses produced by the constrained k-means algorithm, which works as a weak learner under the boosting principle. Experimental results for 12 data sets from 3 data sources demonstrated that our method has performance competitive to those of state-of-the-art constrained clustering methods for most data sets and that it takes much less computation time. Experimental evaluation demonstrated the effectiveness of controlling the constraint priorities by using the boosting principle and that our constrained k-means algorithm functions correctly as a weak learner of boosting.

Boosted black holes on Kaluza-Klein bubbles

International Nuclear Information System (INIS)

Iguchi, Hideo; Mishima, Takashi; Tomizawa, Shinya

2007-01-01

We construct an exact stationary solution of black-hole-bubble sequence in the five-dimensional Kaluza-Klein theory by using solitonic solution-generating techniques. The solution describes two stationary black holes with topology S 3 on a Kaluza-Klein bubble and has a linear momentum component in the compactified direction. We call the solution boosted black holes on Kaluza-Klein bubble because it has the linear momentum. The Arnowitt-Deser-Misner mass and the linear momentum depend on the two boosted velocity parameters of black holes. In the effective four-dimensional theory, the solution has an electric charge which is proportional to the linear momentum. The solution includes the static solution found by Elvang and Horowitz. The small and the big black holes limits are investigated. The relation between the solution and the single boosted black string are considered

Grid Connected Solar PV System with SEPIC Converter Compared with Parallel Boost Converter Based MPPT

Directory of Open Access Journals (Sweden)

T. Ajith Bosco Raj

2014-01-01

Full Text Available The main objective of this work is to study the behaviour of the solar PV systems and model the efficient Grid-connected solar power system. The DC-DC MPPT circuit using chaotic pulse width modulation has been designed to track maximum power from solar PV module. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme. This paper also proposes a simplified multilevel (seven level inverter for a grid-connected photovoltaic system. The primary goal of these systems is to increase the energy injected to the grid by keeping track of the maximum power point of the panel, by reducing the switching frequency, and by providing high reliability. The maximum power has been tracked experimentally. It is compared with parallel boost converter. Also this model is based on mathematical equations and is described through an equivalent circuit including a PV source with MPPT, a diode, a series resistor, a shunt resistor, and dual boost converter with active snubber circuit. This model can extract PV power and boost by using dual boost converter with active snubber. By using this method the overall system efficiency is improved thereby reducing the switching losses and cost.

Solar-Based Boost Differential Single Phase Inverter | Eya | Nigerian ...

African Journals Online (AJOL)

Solar-Based Boost Differential Single Phase Inverter. ... Solar-based boost differential inverter is reduced down to 22.37% in closed loop system with the aid of Proportional –integral-Differential (PID) ... The dc power source is photovoltaic cell.

Substructure boosts to dark matter annihilation from Sommerfeld enhancement

International Nuclear Information System (INIS)

Bovy, Jo

2009-01-01

The recently introduced Sommerfeld enhancement of the dark matter annihilation cross section has important implications for the detection of dark matter annihilation in subhalos in the Galactic halo. In addition to the boost to the dark matter annihilation cross section from the high densities of these subhalos with respect to the main halo, an additional boost caused by the Sommerfeld enhancement results from the fact that they are kinematically colder than the Galactic halo. If we further believe the generic prediction of the cold dark matter paradigm that in each subhalo there is an abundance of substructure which is approximately self-similar to that of the Galactic halo, then I show that additional boosts coming from the density enhancements of these small substructures and their small velocity dispersions enhance the dark matter annihilation cross section even further. I find that very large boost factors (10 5 to 10 9 ) are obtained in a large class of models. The implications of these boost factors for the detection of dark matter annihilation from dwarf spheroidal galaxies in the Galactic halo are such that, generically, they outshine the background gamma-ray flux and are detectable by the Fermi Gamma-ray Space Telescope.

MODELING AND SHIFTING FOCUS AS A FACILITATOR FOR INTENTIONAL EMERGENCE IN TRANSFORMATION DESIGN

DEFF Research Database (Denmark)

Nielsen, Louise Møller; Hansen, Poul H. Kyvsgård; Mabogunje, Ade

2009-01-01

In this paper we discuss the phenomenon "intentional emergence" in a transformation design context. We examine modeling and play enablers for intentional emergence and report on experiences with the Lego Serious Play method. The empirical observations are based on a real-time transformation design...

TOPOLOGICAL REVIEW AND ANALYSIS OF DC-DC BOOST CONVERTERS

Directory of Open Access Journals (Sweden)

V. INDRA GANDHI

2017-06-01

Full Text Available DC voltage boost up is essential in numerous applications; especially considering Photovoltaic (PV based renewable power generation system. The conventional DC-DC boost converter is the most admired configuration for this scheme, even if the converter efficiency is restricted at duty cycle near to maximum value. In order to find solution to the problem and improve its conversion capability, many converter configurations have been implemented so far. With this circumstance, this research work proposes to give overview of a few most imperative research works related to DC-DC boost converters. Some configurations are covered and classified basically based on the application. The major benefits and disadvantages related to the available techniques are also briefly conveyed. At last, a proper evaluation is recognized among the important types of DC-DC boost converters in terms of efficiency, number of components, and stability.

Top reconstruction and boosted top experimental overview

CERN Document Server

Skinnari, Louise

2015-01-01

An overview of techniques used to reconstruct resolved and boosted top quarks is presented. Techniques for resolved top quark reconstruction include kinematic likelihood fitters and pseudo- top reconstruction. Many tools and methods are available for the reconstruction of boosted top quarks, such as jet grooming techniques, jet substructure variables, and dedicated top taggers. Different techniques as used by ATLAS and CMS analyses are described and the performance of different variables and top taggers are shown.

Brachytherapy Boost Utilization and Survival in Unfavorable-risk Prostate Cancer.

Science.gov (United States)

Johnson, Skyler B; Lester-Coll, Nataniel H; Kelly, Jacqueline R; Kann, Benjamin H; Yu, James B; Nath, Sameer K

2017-11-01

There are limited comparative survival data for prostate cancer (PCa) patients managed with a low-dose rate brachytherapy (LDR-B) boost and dose-escalated external-beam radiotherapy (DE-EBRT) alone. To compare overall survival (OS) for men with unfavorable PCa between LDR-B and DE-EBRT groups. Using the National Cancer Data Base, we identified men with unfavorable PCa treated between 2004 and 2012 with androgen suppression (AS) and either EBRT followed by LDR-B or DE-EBRT (75.6-86.4Gy). Treatment selection was evaluated using logistic regression and annual percentage proportions. OS was analyzed using the Kaplan-Meier method, log-rank test, Cox proportional hazards, and propensity score matching. We identified 25038 men between 2004 and 2012, during which LDR-B boost utilization decreased from 29% to 14%. LDR-B was associated with better OS on univariate (7-yr OS: 82% vs 73%; pLDR-B boost (HR 0.74, 95% CI 0.66-0.89). The OS benefit of LDR-B boost persisted when limited to men aged LDR-B boost utilization declined and was associated with better OS compared to DE-EBRT alone. LDR-B boost is probably the ideal treatment option for men with unfavorable PCa, pending long-term results of randomized trials. We compared radiotherapy utilization and survival for prostate cancer (PCa) patients using a national database. We found that low-dose rate brachytherapy (LDR-B) boost, a method being used less frequently, was associated with better overall survival when compared to dose-escalated external-beam radiotherapy alone for men with unfavorable PCa. Randomized trials are needed to confirm that LDR-B boost is the ideal treatment. Copyright © 2017 European Association of Urology. Published by Elsevier B.V. All rights reserved.

A New Method for Start-up of Isolated Boost Converters Using Magnetic- and Winding-Integration

DEFF Research Database (Denmark)

Lindberg-Poulsen, Kristian; Ouyang, Ziwei; Sen, Gökhan

2012-01-01

. The traditional added flyback winding coupled to the boost inductor is thus eliminated from the circuit, bringing substantial cost savings, increased efficiency and simplified design. Each subinterval of the converter operation is described through electrical and magnetic circuit diagrams, and the concept...

Rectificador monofásico con corrección del factor de potencia usando un convertidor Boost

Directory of Open Access Journals (Sweden)

Lenny Andrés Hernández Fonseca

2012-09-01

Full Text Available This paper shows a mathematical model and corresponding controller design of a 24W DC-DC Boost converter used for power factor correction. Modeling and simulations are shown (using Matlab together with experimental results.

arXiv Inelastic Boosted Dark Matter at Direct Detection Experiments

CERN Document Server

Giudice, Gian F.; Park, Jong-Chul; Shin, Seodong

2018-05-10

We explore a novel class of multi-particle dark sectors, called Inelastic Boosted Dark Matter (iBDM). These models are constructed by combining properties of particles that scatter off matter by making transitions to heavier states (Inelastic Dark Matter) with properties of particles that are produced with a large Lorentz boost in annihilation processes in the galactic halo (Boosted Dark Matter). This combination leads to new signals that can be observed at ordinary direct detection experiments, but require unconventional searches for energetic recoil electrons in coincidence with displaced multi-track events. Related experimental strategies can also be used to probe MeV-range boosted dark matter via their interactions with electrons inside the target material.

Design of a PWR emergency core cooling simulator loop

International Nuclear Information System (INIS)

Melo, C.A. de.

1982-12-01

The preliminary design of a PWR Emergency Core Cooling Simulator Loop for investigations of the phenomena involved in a postulated Loss-of-Coolant Accident, during the Reflooding Phase, is presented. The functions of each component of the loop, the design methods and calculations, the specification of the instrumentation, the system operation sequence, the materials list and a cost assessment are included. (Author) [pt

adabag: An R Package for Classification with Boosting and Bagging

Directory of Open Access Journals (Sweden)

Esteban Alfaro

2013-09-01

Full Text Available Boosting and bagging are two widely used ensemble methods for classification. Their common goal is to improve the accuracy of a classifier combining single classifiers which are slightly better than random guessing. Among the family of boosting algorithms, AdaBoost (adaptive boosting is the best known, although it is suitable only for dichotomous tasks. AdaBoost.M1 and SAMME (stagewise additive modeling using a multi-class exponential loss function are two easy and natural extensions to the general case of two or more classes. In this paper, the adabag R package is introduced. This version implements AdaBoost.M1, SAMME and bagging algorithms with classification trees as base classifiers. Once the ensembles have been trained, they can be used to predict the class of new samples. The accuracy of these classifiers can be estimated in a separated data set or through cross validation. Moreover, the evolution of the error as the ensemble grows can be analysed and the ensemble can be pruned. In addition, the margin in the class prediction and the probability of each class for the observations can be calculated. Finally, several classic examples in classification literature are shown to illustrate the use of this package.

Design Facilitation as Emerging Practice: Analyzing How Designers Support Multi-stakeholder Co-creation

Directory of Open Access Journals (Sweden)

Manuela Aguirre

Full Text Available Designers increasingly find themselves facilitating large-scale design events. Yet few have explored design facilitation as an emerging practice. This article examines the design facilitation practices used in two Norwegian case studies of multi-stakeholder events. We focus on the contextually designed tools designers create to help them facilitate. We then explore some critical dimensions of design facilitation. When used as visual overlays, facilitators’ explicit knowledge of these dimensions can improve their capacity to analyze, evaluate, and plan how to design and use contextual tools during design events. By plotting how designers use facilitation tools sequentially during events, we render the flow of design facilitation practice visible and accessible. We suggest that an explicit awareness of these dimensions and flows can enable designers to build more inclusive and inspiring tools, orchestrate the flow of long-term participatory processes more deliberately, and better equip participants to work with complex systemic change.

Tumour bed boost radiotherapy for women after breast-conserving surgery.

Science.gov (United States)

Kindts, Isabelle; Laenen, Annouschka; Depuydt, Tom; Weltens, Caroline

2017-11-06

Breast-conserving therapy, involving breast-conserving surgery followed by whole-breast irradiation and optionally a boost to the tumour bed, is a standard therapeutic option for women with early-stage breast cancer. A boost to the tumour bed means that an extra dose of radiation is applied that covers the initial tumour site. The rationale for a boost of radiotherapy to the tumour bed is that (i) local recurrence occurs mostly at the site of the primary tumour because remaining microscopic tumour cells are most likely situated there; and (ii) radiation can eliminate these causative microscopic tumour cells. The boost continues to be used in women at high risk of local recurrence, but is less widely accepted for women at lower risk. Reasons for questioning the boost are twofold. Firstly, the boost brings higher treatment costs. Secondly, the potential adverse events are not negligible. In this Cochrane Review, we investigated the effect of the tumour bed boost on local control and side effects. To assess the effects of tumour bed boost radiotherapy after breast-conserving surgery and whole-breast irradiation for the treatment of breast cancer. We searched the Cochrane Breast Cancer Specialised Register, the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE (January 1966 to 1 March 2017), Embase (1980 to 1 March 2017), the World Health Organization International Clinical Trials Registry Platform, and ClinicalTrials.gov on 1 March 2017. We also searched the European Society of Radiotherapy and Oncology Annual Meeting, the St Gallen Oncology Conferences, and the American Society for Radiation Oncology Annual Meeting for abstracts. Randomised controlled trials comparing the addition and the omission of breast cancer tumour bed boost radiotherapy. Two review authors (IK and CW) performed data extraction and assessed risk of bias using Cochrane's 'Risk of bias' tool, resolving any disagreements through discussion. We entered data into Review Manager 5 for

The Synergy Between PAV and AdaBoost

OpenAIRE

WILBUR, W. JOHN; YEGANOVA, LANA; KIM, WON

2005-01-01

Schapire and Singer’s improved version of AdaBoost for handling weak hypotheses with confidence rated predictions represents an important advance in the theory and practice of boosting. Its success results from a more efficient use of information in weak hypotheses during updating. Instead of simple binary voting a weak hypothesis is allowed to vote for or against a classification with a variable strength or confidence. The Pool Adjacent Violators (PAV) algorithm is a method for converting a ...

14 CFR 27.695 - Power boost and power-operated control system.

Science.gov (United States)

2010-01-01

... Systems § 27.695 Power boost and power-operated control system. (a) If a power boost or power-operated... failure of all engines. (b) Each alternate system may be a duplicate power portion or a manually operated... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Power boost and power-operated control...

14 CFR 29.695 - Power boost and power-operated control system.

Science.gov (United States)

2010-01-01

... Systems § 29.695 Power boost and power-operated control system. (a) If a power boost or power-operated... failure of all engines. (b) Each alternate system may be a duplicate power portion or a manually operated... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Power boost and power-operated control...

An improved soft switched PWM interleaved boost AC-DC converter

International Nuclear Information System (INIS)

Genc, Naci; Iskender, Ires

2011-01-01

In this paper, an improved soft switched two cell interleaved boost AC/DC converter with high power factor is proposed and investigated. A new auxiliary circuit is designed and added to two cell interleaved boost converter to reduce the switching losses. The proposed auxiliary circuit is implemented using only one auxiliary switch and a minimum number of passive components without an important increase in the cost and complexity of the converter. The main advantage of this auxiliary circuit is that it not only provides zero-voltage-transition (ZVT) for the main switches but also provides soft switching for the auxiliary switch and diodes. Though all semiconductor devices operate under soft switching, they do not have any additional voltage and current stresses. The proposed converter operates successfully in soft switching operation mode for a wide range of input voltage level and the load. In addition, it has advantages such as fewer structure complications, lower cost and ease of control. In the study, the transition modes for describing the behavior of the proposed converter in one switching period are described. A prototype with 600 W output power, 50 kHz/cell switching frequency, input line voltage of 110-220 V rms and an output voltage of 400 V dc has been implemented. Analysis, design and the control circuitry are also presented in the paper.

Conceptual design of the national nuclear emergency management information system

International Nuclear Information System (INIS)

Wang Xingyu; Shi Zhongqi

2003-01-01

A Conceptual Design of the National Nuclear Emergency Management Information System was brought forward in this paper, based on the summarization of some emergency management information systems used in China and some other countries. The conceptual system should have four basic characteristics, that are (1) a graphic displaying and querying interface based on GIS (2) data and results shared with the assessment software of nuclear accident (3) a complete set of databases and (4) the capability of on-line data receiving or real-time distributing of the commands and information for emergency response

Using data to drive emergency department design: a metasynthesis.

Science.gov (United States)

Welch, Shari J

2012-01-01

There has been an uptick in the field of emergency department (ED) operations research and data gathering, both published and unpublished. This new information has implications for ED design. The specialty suffers from an inability to have these innovations reach frontline practitioners, let alone design professionals and architects. This paper is an attempt to synthesize for design professionals the growing data regarding ED operations. The following sources were used to capture and summarize the research and data collections available regarding ED operations: the Emergency Department Benchmarking Alliance database; a literature search using both PubMed and Google Scholar search engines; and data presented at conferences and proceedings. Critical information that affects ED design strategies is summarized, organized, and presented. Data suggest an optimal size for ED functional units. The now-recognized arrival and census curves for the ED suggest a department that expands and contracts in response to changing census. Operational improvements have been dearly identified and are grouped into three categories: input, throughput, and outflow. Applications of this information are suggested. The sentinel premise of this meta-synthesis is that data derived from improvement work in the area of ED operations has applications for ED design. EDs can optimize their functioning by marrying good processes and operations to good design. This review paper is an attempt to bring this new information to the attention of the multidisciplinary team of architects, designers, and clinicians.

Non-Inverting Buck-Boost Converter for Fuel Cell Applications

DEFF Research Database (Denmark)

Schaltz, Erik; Rasmussen, Peter Omand; Khaligh, Alireza

2008-01-01

Fuel cell DC/DC converters often have to be able to both step-up and step-down the input voltage, and provide a high efficiency in the whole range of output power. Conventional negative output buck-boost and non-inverting buck-boost converters provide both step-up and step-down characteristics....... In this paper the non-inverting buck-boost with either diodes or synchronous rectifiers is investigated for fuel cell applications. Most of previous research does not consider  the parasitic in the evaluation of the converters. In this study, detailed analytical expressions of the efficiencies for the system...

A New Approach to High Efficincy in Isolated Boost Converters for High-Power Low-Voltage Fuel Cell Apllications

DEFF Research Database (Denmark)

Nymand, Morten; Andersen, Michael A. E.

2008-01-01

A new low-leakage-inductance low-resistance design approach to low-voltage high-power isolated boost converters is presented. Very low levels of parasitic circuit inductances are achieved by optimizing transformer design and circuit lay-out. Primary side voltage clamp circuits can be eliminated...... by the use of power MOSFETs fully rated for repetitive avalanche. Voltage rating of primary switches can now be reduced, significantly reducing switch on-state losses. Finally, silicon carbide rectifying diodes allow fast diode turn-off, further reducing losses. Test results from a 1.5 kW full-bridge boost...... converter verify theoretical analysis and demonstrate very high efficiency. Worst case efficiency, at minimum input voltage maximum power, is 96.8 percent and maximum efficiency reaches 98 percent....

Impact of intensity-modulated radiation therapy as a boost treatment on the lung-dose distributions for non-small-cell lung cancer

International Nuclear Information System (INIS)

Choi, Youngmin; Kim, Jeung Kee; Lee, Hyung Sik; Hur, Won Joo; Chai, Gyu Young; Kang, Ki Mun

2005-01-01

Purpose: To investigate the feasibility of intensity-modulated radiotherapy (IMRT) as a method of boost radiotherapy after the initial irradiation by the conventional anterior/posterior opposed beams for centrally located non-small-cell lung cancer through the evaluation of dose distributions according to the various boost methods. Methods and Materials: Seven patients with T3 or T4 lung cancer and mediastinal node enlargement who previously received radiotherapy were studied. All patients underwent virtual simulation retrospectively with the previous treatment planning computed tomograms. Initial radiotherapy plans were designed to deliver 40 Gy to the primary tumor and involved nodal regions with the conventional anterior/posterior opposed beams. Two radiation dose levels, 24 and 30 Gy, were used for the boost radiotherapy plans, and four different boost methods (a three-dimensional conformal radiotherapy [3DCRT], five-, seven-, and nine-beam IMRT) were applied to each dose level. The goals of the boost plans were to deliver the prescribed radiation dose to 95% of the planning target volume (PTV) and minimize the volumes of the normal lungs and spinal cord irradiated above their tolerance doses. Dose distributions in the PTVs and lungs, according to the four types of boost plans, were compared in the boost and sum plans, respectively. Results: The percentage of lung volumes irradiated >20 Gy (V20) was reduced significantly in the IMRT boost plans compared with the 3DCRT boost plans at the 24- and 30-Gy dose levels (p 0.007 and 0.0315 respectively). Mean lung doses according to the boost methods were not different in the 24- and 30-Gy boost plans. The conformity indexes (CI) of the IMRT boost plans were lower than those of the 3DCRT plans in the 24- and 30-Gy plans (p = 0.001 in both). For the sum plans, there was no difference of the dose distributions in the PTVs and lungs according to the boost methods. Conclusions: In the boost plans the V20s and CIs were

DESAIN DAN IMPLEMENTSI SOFT SWITCHING BOOST KONVERTER DENGAN SIMPLE AUXILLARY RESONANT SWITCH (SARC

Directory of Open Access Journals (Sweden)

Dimas Bagus Saputra

2017-01-01

Full Text Available Boost konverter merupakan penaik tegangan DC ke tegangan DC yang mempunyai tegangan output yang lebih tinggi dibanding inputnya. Penggunaan boost konverter diera modern semakin meningkat dan dibuat dengan dimensi yang lebih kecil, berat yang lebih ringan dan efisiensi yang lebih tinggi dibanding dengan boost konverter generasi terdahulu. Tetapi rugi-rugi periodik saat on/off meningkat. Untuk meraih kriteria tersebut, teknik hard switching boost konverter berevolusi menjadi teknik soft switching dengan menambah rangkaian simple auxiliary resonant circuit (SARC. Karena penambahan rangkaian SARC tersebut konverter bekerja pada kondisi zero-voltage switching switch (ZVS dan zero current switch (ZCS, sehingga saklar semikonduktor tidak bekerja secara hard switching lagi. Pada penelitian ini akan di desain dan diimplementaskan soft switching boost konverter dengan SARC. Kelebihan dari soft switching boost konverter dengan SARC adalah mempunyai efisiensi yang lebih tinggi dibanding dengan boost konverter konventional. Dari hasil implementasi menunjukkan konverter yang diajukan telah meraih zero voltage switch (ZVS. Sehingga boost konverter zero voltage switch (ZVS bisa diaplikasikan pada sistem power suplay yang membutuhkan efisiensi energi yang tinggi terutama pada daya yang tinggi.

An evaluation of a hubless inducer and a full flow hydraulic turbine driven inducer boost pump

Science.gov (United States)

Lindley, B. K.; Martinson, A. R.

1971-01-01

The purpose of the study was to compare the performance of several configurations of hubless inducers with a hydrodynamically similar conventional inducer and to demonstrate the performance of a full flow hydraulic turbine driven inducer boost pump using these inducers. A boost pump of this type consists of an inducer connected to a hydraulic turbine with a high speed rotor located in between. All the flow passes through the inducer, rotor, and hydraulic turbine, then into the main pump. The rotor, which is attached to the main pump shaft, provides the input power to drive the hydraulic turbine which, in turn, drives the inducer. The inducer, rotating at a lower speed, develops the necessary head to prevent rotor cavitation. The rotor speed is consistent with present main engine liquid hydrogen pump designs and the overall boost pump head rise is sufficient to provide adequate main pump suction head. This system would have the potential for operating at lower liquid hydrogen tank pressures.

Design Optimization of Internal Flow Devices

DEFF Research Database (Denmark)

Madsen, Jens Ingemann

The power of computational fluid dynamics is boosted through the use of automated design optimization methodologies. The thesis considers both derivative-based search optimization and the use of response surface methodologies.......The power of computational fluid dynamics is boosted through the use of automated design optimization methodologies. The thesis considers both derivative-based search optimization and the use of response surface methodologies....

Y-Source Boost DC/DC Converter for Distributed Generation

DEFF Research Database (Denmark)

Siwakoti, Yam P.; Loh, Poh Chiang; Blaabjerg, Frede

2015-01-01

This paper introduces a versatile Y-source boost dc/dc converter intended for distributed power generation, where high gain is often demanded. The proposed converter uses a Y-source impedance network realized with a tightly coupled three-winding inductor for high voltage boosting that is presently...

Investigation of the charge boost technology for the efficiency increase of closed sorption thermal energy storage systems

Science.gov (United States)

Rohringer, C.; Engel, G.; Köll, R.; Wagner, W.; van Helden, W.

2017-10-01

The inclusion of solar thermal energy into energy systems requires storage possibilities to overcome the gap between supply and demand. Storage of thermal energy with closed sorption thermal energy systems has the advantage of low thermal losses and high energy density. However, the efficiency of these systems needs yet to be increased to become competitive on the market. In this paper, the so-called “charge boost technology” is developed and tested via experiments as a new concept for the efficiency increase of compact thermal energy storages. The main benefit of the charge boost technology is that it can reach a defined state of charge for sorption thermal energy storages at lower temperature levels than classic pure desorption processes. Experiments are conducted to provide a proof of principle for this concept. The results show that the charge boost technology does function as predicted and is a viable option for further improvement of sorption thermal energy storages. Subsequently, a new process application is developed by the author with strong focus on the utilization of the advantages of the charge boost technology over conventional desorption processes. After completion of the conceptual design, the theoretical calculations are validated via experiments.

Dosimetric comparison of the related parameters between simultaneous integrated boost intensity-modulated radiotherapy and sequential boost conformal radiotherapy for postoperative malignant glioma of the brain

International Nuclear Information System (INIS)

Shao Qian; Lu Jie; Li Jianbin; Sun Tao; Bai Tong; Liu Tonghai; Yin Yong

2011-01-01

Objective: To compare the dosimetric of different parameter of simultaneous integrated boost intensity-modulated radiotherapy (SIB-IMRT) with sequential boost conformal radiotherapy (SB-CRT) for postoperative malignant glioma of the brain. Methods: Ten patients with malignant glioma of brain were selected to study. Each patient was simulated all by CT and MRI, and the imagings of CT and MRI were all sent to Pinnacle 3 planning system. The fusion technology with MR-CT imaging was used on Pinnacle 3 planning system. The target volume was delineated and defined based on MRI. The postoperative residual lesion and resection cavity were defined as gross tumor volume (GTV) and expanded GTV some scope was defined as clinical target volume (CTV). The margins of GTV expanded 10 mm and 25 mm were defined as CTV1 and CTV2 respectively. CTV1 and CTV2 all enlarged 5 mm were defined as PTV1 and PTV2 respectively. The plans of simultaneous integrated boost intensity-modulated radiotherapy and sequential boost conformal radiotherapy were respectively designed for each patient using Pinnacle 3 planning system and the dosimetric of different parameter was compared. The prescribe dose of SIB-IMRT was PTV1: 62.5 Gy/25 f, PTV2: 50.0 Gy/25 f; and SB-CRT was PTV1: 66.0 Gy/33 f, PTV2: 50.0 Gy/25 f. The dosimetries of different parameters of SIB-IMRT and SB-CRT were compared by using Paired-Samples T Test. Results: The maximum and mean dose of PTV1, PTV2, and brainstem were of significant difference (P 0.05). Conclusion: The SIB-IMRT plan is better than the SB-CRT plan. The CI and HI of SIB-IMRT are superior to SB-CRT. At the same time, it can preserve the important organs such as brainstem and reduce the mean dose of whole brain. On the other hand it can shorten the total period of therapy time. (authors)

Boost breaking in the EFT of inflation

Energy Technology Data Exchange (ETDEWEB)

Delacrétaz, Luca V.; Senatore, Leonardo [Stanford Institute for Theoretical Physics, Stanford University, Stanford, CA 94305 (United States); Noumi, Toshifumi, E-mail: lvd@stanford.edu, E-mail: tnoumi@phys.sci.kobe-u.ac.jp, E-mail: senatore@stanford.edu [Jockey Club Institute for Advanced Study, Hong Kong University of Science and Technology (Hong Kong)

2017-02-01

If time-translations are spontaneously broken, so are boosts. This symmetry breaking pattern can be non-linearly realized by either just the Goldstone boson of time translations, or by four Goldstone bosons associated with time translations and boosts. In this paper we extend the Effective Field Theory of Multifield Inflation to consider the case in which the additional Goldstone bosons associated with boosts are light and coupled to the Goldstone boson of time translations. The symmetry breaking pattern forces a coupling to curvature so that the mass of the additional Goldstone bosons is predicted to be equal to √2 H in the vast majority of the parameter space where they are light. This pattern therefore offers a natural way of generating self-interacting particles with Hubble mass during inflation. After constructing the general effective Lagrangian, we study how these particles mix and interact with the curvature fluctuations, generating potentially detectable non-Gaussian signals.

Design and Simulation to Composite PI Controller on the Stratospheric Airship

OpenAIRE

Kangwen Sun; Ming Zhu; Bojin Qi; Xiaoming Chen

2014-01-01

In view of the stratospheric airship application requirements on energy storage and management system, based on the topology of DC/DC converter main circuit, the composite PI controller is designed to realize respective control with the Boost mode and Buck mode. Furthermore, limit stop integration method is proposed to achieve a buck-boost complex DC/DC converter boost with effective switching buck. Then, with the MATLAB Control System Toolbox design model, the composite PI controller design ...

Three-Dimensional Conformal Simultaneously Integrated Boost Technique for Breast-Conserving Radiotherapy

International Nuclear Information System (INIS)

Laan, Hans Paul van der; Dolsma, Wil V.; Maduro, John H.; Korevaar, Erik W.; Hollander, Miranda; Langendijk, Johannes A.

2007-01-01

Purpose: To compare the target coverage and normal tissue dose with the simultaneously integrated boost (SIB) and the sequential boost technique in breast cancer, and to evaluate the incidence of acute skin toxicity in patients treated with the SIB technique. Methods and Materials: Thirty patients with early-stage left-sided breast cancer underwent breast-conserving radiotherapy using the SIB technique. The breast and boost planning target volumes (PTVs) were treated simultaneously (i.e., for each fraction, the breast and boost PTVs received 1.81 Gy and 2.3 Gy, respectively). Three-dimensional conformal beams with wedges were shaped and weighted using forward planning. Dose-volume histograms of the PTVs and organs at risk with the SIB technique, 28 x (1.81 + 0.49 Gy), were compared with those for the sequential boost technique, 25 x 2 Gy + 8 x 2 Gy. Acute skin toxicity was evaluated for 90 patients treated with the SIB technique according to Common Terminology Criteria for Adverse Events, version 3.0. Results: PTV coverage was adequate with both techniques. With SIB, more efficiently shaped boost beams resulted in smaller irradiated volumes. The mean volume receiving ≥107% of the breast dose was reduced by 20%, the mean volume outside the boost PTV receiving ≥95% of the boost dose was reduced by 54%, and the mean heart and lung dose were reduced by 10%. Of the evaluated patients, 32.2% had Grade 2 or worse toxicity. Conclusion: The SIB technique is proposed for standard use in breast-conserving radiotherapy because of its dose-limiting capabilities, easy implementation, reduced number of treatment fractions, and relatively low incidence of acute skin toxicity

Measuring performance in health care: case-mix adjustment by boosted decision trees.

Science.gov (United States)

Neumann, Anke; Holstein, Josiane; Le Gall, Jean-Roger; Lepage, Eric

2004-10-01

The purpose of this paper is to investigate the suitability of boosted decision trees for the case-mix adjustment involved in comparing the performance of various health care entities. First, we present logistic regression, decision trees, and boosted decision trees in a unified framework. Second, we study in detail their application for two common performance indicators, the mortality rate in intensive care and the rate of potentially avoidable hospital readmissions. For both examples the technique of boosting decision trees outperformed standard prognostic models, in particular linear logistic regression models, with regard to predictive power. On the other hand, boosting decision trees was computationally demanding and the resulting models were rather complex and needed additional tools for interpretation. Boosting decision trees represents a powerful tool for case-mix adjustment in health care performance measurement. Depending on the specific priorities set in each context, the gain in predictive power might compensate for the inconvenience in the use of boosted decision trees.

Emergent Artefacts of Ethnography and Processual Engagements of design

DEFF Research Database (Denmark)

Wallace, Jamie

2012-01-01

Relating to processes of design and creativity, the use of artefacts are contrasted between two different disciplines. Pointing to possible challenges, the study considers how collaborative innovation depends upon the interplay between entwined and emergent artefact worlds and their related skill...

The development of a subsea power transmission system for deep water boosting applications

Energy Technology Data Exchange (ETDEWEB)

Godinho, C.A.F. [Pirelli Cabos S.A. (Brazil); Campagnac, L.A. [Siemens S.A. (Brazil); Nicholson, A. [Tronic Electronics Services Ltd. (WEC); Magalhaes, W.M. de [PETROBRAS, Rio de Janeiro, RJ (Brazil)

1996-12-31

This paper presents the development of a sub sea power transmission in medium voltage and variable frequency, as a key system for application of Boosting technology and for electrical submersible Pumping in deep water wells. This work focuses on the design and manufacture of sub sea power cables and transformers for 1,000 m water depth. 8 refs., 6 figs.

Streamlining the Design-to-Build Transition with Build-Optimization Software Tools.

Science.gov (United States)

Oberortner, Ernst; Cheng, Jan-Fang; Hillson, Nathan J; Deutsch, Samuel

2017-03-17

Scaling-up capabilities for the design, build, and test of synthetic biology constructs holds great promise for the development of new applications in fuels, chemical production, or cellular-behavior engineering. Construct design is an essential component in this process; however, not every designed DNA sequence can be readily manufactured, even using state-of-the-art DNA synthesis methods. Current biological computer-aided design and manufacture tools (bioCAD/CAM) do not adequately consider the limitations of DNA synthesis technologies when generating their outputs. Designed sequences that violate DNA synthesis constraints may require substantial sequence redesign or lead to price-premiums and temporal delays, which adversely impact the efficiency of the DNA manufacturing process. We have developed a suite of build-optimization software tools (BOOST) to streamline the design-build transition in synthetic biology engineering workflows. BOOST incorporates knowledge of DNA synthesis success determinants into the design process to output ready-to-build sequences, preempting the need for sequence redesign. The BOOST web application is available at https://boost.jgi.doe.gov and its Application Program Interfaces (API) enable integration into automated, customized DNA design processes. The herein presented results highlight the effectiveness of BOOST in reducing DNA synthesis costs and timelines.

Stability analysis of a high-step-Up DC grid-connected two-stage boost DC-DC converter

Directory of Open Access Journals (Sweden)

El Aroudi A.

2014-01-01

Full Text Available High conversion ratio switching converters are used whenever there is a need to step-up dc source voltage level to a much higher output dc voltage level such as in photovoltaic systems, telecommunications and in some medical applications. A simple solution for achieving this high conversion ratio is by cascading different stages of dc-dc boost converters. The individual converters in such a cascaded system are usually designed separately applying classical design criteria. However these criteria may not be applicable for the complete cascaded system . This paper first presents a glimpse on the bifurcation behavior that a cascade connection of two boost converters can exhibit. It is shown that the desired periodic orbit can undergo period doubling leading to subharmonic oscillations and chaotic regimes. Then, in order to simplify the analysis the second stage is considered as constant current sink and design-oriented analysis is carried out to obtain stability boundaries in the parameter space by taking into account slope interactions between the state variables in the two-different stages.

Concomitant GRID boost for Gamma Knife radiosurgery

International Nuclear Information System (INIS)

Ma Lijun; Kwok, Young; Chin, Lawrence S.; Simard, J. Marc; Regine, William F.

2005-01-01

We developed an integrated GRID boost technique for Gamma Knife radiosurgery. The technique generates an array of high dose spots within the target volume via a grid of 4-mm shots. These high dose areas were placed over a conventional Gamma Knife plan where a peripheral dose covers the full target volume. The beam weights of the 4-mm shots were optimized iteratively to maximize the integral dose inside the target volume. To investigate the target volume coverage and the dose to the adjacent normal brain tissue for the technique, we compared the GRID boosted treatment plans with conventional Gamma Knife treatment plans using physical and biological indices such as dose-volume histogram (DVH), DVH-derived indices, equivalent uniform dose (EUD), tumor control probabilities (TCP), and normal tissue complication probabilities (NTCP). We found significant increase in the target volume indices such as mean dose (5%-34%; average 14%), TCP (4%-45%; average 21%), and EUD (2%-22%; average 11%) for the GRID boost technique. No significant change in the peripheral dose coverage for the target volume was found per RTOG protocol. In addition, the EUD and the NTCP for the normal brain adjacent to the target (i.e., the near region) were decreased for the GRID boost technique. In conclusion, we demonstrated a new technique for Gamma Knife radiosurgery that can escalate the dose to the target while sparing the adjacent normal brain tissue

Emergent features and perceptual objects: re-examining fundamental principles in analogical display design.

Science.gov (United States)

Holt, Jerred; Bennett, Kevin B; Flach, John M

2015-01-01

Two sets of design principles for analogical visual displays, based on the concepts of emergent features and perceptual objects, are described. An interpretation of previous empirical findings for three displays (bar graph, polar graphic, alphanumeric) is provided from both perspectives. A fourth display (configural coordinate) was designed using principles of ecological interface design (i.e. direct perception). An experiment was conducted to evaluate performance (accuracy and latency of state identification) with these four displays. Numerous significant effects were obtained and a clear rank ordering of performance emerged (from best to worst): configural coordinate, bar graph, alphanumeric and polar graphic. These findings are consistent with principles of design based on emergent features; they are inconsistent with principles based on perceptual objects. Some limitations of the configural coordinate display are discussed and a redesign is provided. Practitioner Summary: Principles of ecological interface design, which emphasise the quality of very specific mappings between domain, display and observer constraints, are described; these principles are applicable to the design of all analogical graphical displays.

Boosting aquaculture production systems in Osun state: Role of ...

African Journals Online (AJOL)

This scenario leaves a high percentage of the population who depend on fish and fish products food insecure, and thus, the need to boost aquaculture production to argument the supply from the wild. The study therefore looks into the possibility of boosting the production systems through the use of micro-credit and ...

Powerful boost for Indian lignite

Energy Technology Data Exchange (ETDEWEB)

1985-06-01

The Neyveli Lignite Corporation (NLC) of India has begun the first phase of an expansion program that will open a second mine and boost lignite production in Tamil Nadu to nearly five times its present level within the next 15 years. Mining conditions at Neyveli are particularly difficult. The harsh abrasive overburden strata present severe and strenuous conditions; sticky and marshy surface clays, the presence of groundwater aquifers, the cyclonic and monsoonal climate and high stripping ratios are other problems. The overburden is drilled and blasted; in areas of sticky topsoil, non-stick liners for the buckets etc. are used. Adequate safeguards and infrastructure are being developed to deal with differing strata conditions. The conveyor transport system features slow, wider belt conveyors, changeover from fixed type roller to freely hanging garland type, interlinking of benches and specially designed drive heads. The groundwater aquifers are continuously depressurized by grid pumping from a series of pumps; boreholes have been sunk to 120 m.

A study on HCI design strategy using emergent features and response time

International Nuclear Information System (INIS)

Lee, Sung Jin; Chang, Soon Heung; Park, Jin Gyun

2001-01-01

Existing design process of user interface has some weak point that there is no feedback information and no quantitative information between each sub process. If they're such information in design process, the design time cycle will be decreased and the contentment of HCI in the aspect of user will be more easily archived. In this study, new design process with feedback information and quantitative information was proposed using emergent features and user response time. The proposed methodology was put together with three main parts. First part is to calculate distinctiveness of a user interface or expanded user interface with consideration of emergent features. Second part is to expand a prototype user interface with design option for purpose of design requirement using directed structure graph (or nodal graph) theory. Last part is to convert non-realized value, distinctiveness, into realized value, response time, by response time database or response time correlation in the form of Hick-Hyman law equation. From the present validations, the usefulness of the proposed methodology was obtained by simple validation testing. It was found that emergent features should be improved for high reflection of real user interface. For the reliability of response time database, lots of end-user experiment is necessary. Expansion algorithm and representation technique of qualitative information should be somewhat improved for more efficient design process

Radiotherapy Breast Boost With Reduced Whole-Breast Dose Is Associated With Improved Cosmesis: The Results of a Comprehensive Assessment From the St. George and Wollongong Randomized Breast Boost Trial

International Nuclear Information System (INIS)

Hau, Eric; Browne, Lois H.; Khanna, Sam; Cail, Stacy; Cert, Grad; Chin, Yaw; Clark, Catherine; Inder, Stephanie; Szwajcer, Alison; Graham, Peter H.

2012-01-01

Purpose: To evaluate comprehensively the effect of a radiotherapy boost on breast cosmetic outcomes after 5 years in patients treated with breast-conserving surgery. Methods: The St. George and Wollongong trial (NCT00138814) randomized 688 patients with histologically proven Tis-2, N 0–1, M0 carcinoma to the control arm of 50 Gy in 25 fractions (342 patients) and the boost arm of 45 Gy in 25 fractions to the whole breast followed by a 16 Gy in 8 fraction electron boost (346 patients). Five-year cosmetic outcomes were assessed by a panel subjectively in 385 patients and objectively using pBRA (relative breast retraction assessment). A subset of patients also had absolute BRA measurements. Clinician assessment and patient self-assessment of overall cosmetic and specific items as well as computer BCCT.core analysis were also performed. Results: The boost arm had improved cosmetic overall outcomes as scored by the panel and BCCT.core software with 79% (p = 0.016) and 81% (p = 0.004) excellent/good cosmesis respectively compared with 68% in no-boost arm. The boost arm also had lower pBRA and BRA values with a mean difference of 0.60 and 1.82 mm, respectively, but was not statistically significant. There was a very high proportion of overall excellent/good cosmetic outcome in 95% and 93% in the boost and no–boost arms using patient self-assessment. However, no difference in overall and specific items scored by clinician assessment and patient self-assessment was found. Conclusion: The results show the negative cosmetic effect of a 16-Gy boost is offset by a lower whole-breast dose of 45 Gy.

Boosted top production in ATLAS and CMS

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00237277; The ATLAS collaboration

2017-01-01

An overview of the boosted top production analyses using data collected by the ATLAS and CMS experiments at $\\sqrt{s}=$' 8 TeV and 13 TeV of proton-proton collisions at the LHC is presented. These analyses use techniques for the reconstruction of boosted objects to measure the production of top quarks at high transverse momenta. The measurements are optimized for the different final states and for different ranges of the transverse momenta of the particles involved, improving on measurements with traditional objects reconstruction based on the combination of resolved objects.

The boosts in the noncommutative special relativity

International Nuclear Information System (INIS)

Lagraa, M.

2001-01-01

From the quantum analogue of the Iwasawa decomposition of SL(2, C) group and the correspondence between quantum SL(2, C) and Lorentz groups we deduce the different properties of the Hopf algebra representing the boost of particles in noncommutative special relativity. The representation of the boost in the Hilbert space states is investigated and the addition rules of the velocities are established from the coaction. The q-deformed Clebsch-Gordon coefficients describing the transformed states of the evolution of particles in noncommutative special relativity are introduced and their explicit calculation are given. (author)

Design and Simulation of a High Performance Emergency Data Delivery Protocol

DEFF Research Database (Denmark)

Swartz, Kevin; Wang, Di

2007-01-01

The purpose of this project was to design a high performance data delivery protocol, capable of delivering data as quickly as possible to a base station or target node. This protocol was designed particularly for wireless network topologies, but could also be applied towards a wired system....... An emergency is defined as any event with high priority that needs to be handled immediately. It is assumed that this emergency event is important enough that energy efficiency is not a factor in our protocol. The desired effect is for fast as possible delivery to the base station for rapid event handling....

Desain dan Implementsi Soft Switching Boost Konverter dengan Simple Auxillary Resonant Switch (Sarc)

OpenAIRE

Saputra, Dimas Bagus; Suryoatmojo, Heri; Musthofa, Arif

2016-01-01

Boost konverter merupakan penaik tegangan DC ke tegangan DC yang mempunyai tegangan output yang lebih tinggi dibanding inputnya. Penggunaan boost konverter diera modern semakin meningkat dan dibuat dengan dimensi yang lebih kecil, berat yang lebih ringan dan efisiensi yang lebih tinggi dibanding dengan boost konverter generasi terdahulu. Tetapi rugi-rugi periodik saat on/off meningkat. Untuk meraih kriteria tersebut, teknik hard switching boost konverter berevolusi menjadi teknik soft switchi...

Emergency Response Program Designing Based On Case Study ERP Regulations In Ilam Gas Refinery

Directory of Open Access Journals (Sweden)

Mehdi Tahmasbi

2015-08-01

Full Text Available The study of Emergency response plan designing is one of the most important prevention approaches in crisis management. This study aims to design emergency response plan based on case study ERP regulations in Ilam gas refinery. On the basis of risk assessment and identification techniques such as HAZOP and FMEA in Ilam gas refinery the risks have been prioritized and then according to this prioritization the design of possible scenarios which have the highest rate of occurrence and the highest level of damage has been separated. Possible scenarios were simulated with PHAST software. Then emergency response program has been designed for the special mode or similar cases. According to the internal emergency response plan for Ilam gas refinery and predictable conditions of the process special instructions should be considered at the time of the incident to suffer the least damage on people and environment in the shortest time possible.

Teacher design of technology for emergent literacy: An explorative feasibility study

NARCIS (Netherlands)

McKenney, Susan; Voogt, Joke

2012-01-01

The active participation of teachers in designing classroom learning experiences contributes to teacher abilities to facilitate learning. This paper reports on a case study of one Dutch teacher designing a technology-rich learning environment for emergent literacy. Data was collected to explore the

Active pre-filters for dc/dc Boost regulators

Directory of Open Access Journals (Sweden)

Carlos Andrés Ramos-Paja

2014-05-01

Full Text Available This paper proposes an active pre-filter to mitigate the current harmonics generated by classical dc/dc Boost regulators, which generate current ripples proportional to the duty cycle. Therefore, high output voltage conditions, i.e., high voltage conversion ratios, produce high current harmonics that must be filtered to avoid damage or source losses. Traditionally, these current components are filtered using electrolytic capacitors, which introduce reliability problems because of their high failure rate. The solution introduced in this paper instead uses a dc/dc converter based on the parallel connection of the Boost canonical cells to filter the current ripples generated by the Boost regulator, improving the system reliability. This solution provides the additional benefits of improving the overall efficiency and the voltage conversion ratio. Finally, the solution is validated with simulations and experimental results.

Comparison of three concomitant boost techniques for early-stage breast cancer

International Nuclear Information System (INIS)

Horton, Janet K.; Halle, Jan S.; Chang, Sha X.; Sartor, Carolyn I.

2006-01-01

Purpose: Whole breast radiotherapy (RT) followed by a tumor bed boost typically spans 5-6 weeks of treatment. Interest is growing in RT regimens, such as concomitant boost, that decrease overall treatment time, lessening the time/cost burden to patients and facilities. Methods and Materials: Computed tomography (CT) scans from 20 cases were selected for this retrospective, dosimetric study to compare three different techniques of concomitant boost delivery: (1) standard tangents plus an electron boost (2) intensity-modulated RT (IMRT) tangents using custom compensators plus an electron boost, and (3) IMRT tangents plus a conformal photon boost. The equivalent uniform dose model was used to compare the plans. Results: The average breast equivalent uniform dose value for the three techniques (standard, IMRT plus electrons, and IMRT plus photons) was 48.6, 47.9, and 48.3, respectively. The plans using IMRT more closely approximated the prescribed dose of 46 Gy to the whole breast. The breast volume receiving >110% of the dose was less with the IMRT tangents than with standard RT (p 0.037), but no significant difference in the maximal dose or other evaluated parameters was noted. Conclusion: Although the IMRT techniques delivered the prescribed dose with better dose uniformity, the small improvement seen did not support a goal of improved resource use

Modeling of asymmetrical boost converters

Directory of Open Access Journals (Sweden)

Eliana Isabel Arango Zuluaga

2014-01-01

Full Text Available The asymmetrical interleaved dual boost (AIDB is a fifth-order DC/DC converter designed to interface photovoltaic (PV panels. The AIDB produces small current harmonics to the PV panels, reducing the power losses caused by the converter operation. Moreover, the AIDB provides a large voltage conversion ratio, which is required to step-up the PV voltage to the large dc-link voltage used in grid-connected inverters. To reject irradiance and load disturbances, the AIDB must be operated in a closed-loop and a dynamic model is required. Given that the AIDB converter operates in Discontinuous Conduction Mode (DCM, classical modeling approaches based on Continuous Conduction Mode (CCM are not valid. Moreover, classical DCM modeling techniques are not suitable for the AIDB converter. Therefore, this paper develops a novel mathematical model for the AIDB converter, which is suitable for control-pur-poses. The proposed model is based on the calculation of a diode current that is typically disregarded. Moreover, because the traditional correction to the second duty cycle reported in literature is not effective, a new equation is designed. The model accuracy is contrasted with circuital simulations in time and frequency domains, obtaining satisfactory results. Finally, the usefulness of the model in control applications is illustrated with an application example.

Modelling, Simulation and Construction of a DC/DC Boost Power Converter: A School Experimental System

Science.gov (United States)

Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernandez-Guzman, V. M.; Saldana-Gonzalez, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

2012-01-01

We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders…

Holocraneal irradiation with boost integrated simultaneous of oligo metastases using Exa frame and Exa skin with VMAI-IGRT

International Nuclear Information System (INIS)

Velazquez Miranda, S.; Montero Perea, E.; Ortiz Seidel, M.

2013-01-01

The described technique of prophylaxis back hippo-fractionated with simultaneous integrated boost presents advantages in terms of reduction of treatment time total, fast local effect on the oligo metastases and possible prevention of the emergence of new cranial metastasis. The possible impact on long-term survival remains to be determined. In any case, this technique is presented as a valid alternative in terms of clinical outcomes and toxicity to stereotaxic standard treatments. (Author)

The Boost study: design of a school- and community-based randomised trial to promote fruit and vegetable consumption among teenagers

Science.gov (United States)

2012-01-01

Background The aim of the Boost study was to produce a persistent increase in fruit and vegetable consumption among 13-year-olds. This paper describes the development, implementation and evaluation of a school-and community-based, multi-component intervention guided by theory, evidence, and best practice. Methods/design We used the Intervention Mapping protocol to guide the development of the intervention. Programme activities combined environmental and educational strategies and focused on increasing access to fruit and vegetables in three settings: School: Daily provision of free fruit and vegetables; a pleasant eating environment; classroom curricular activities; individually computer tailored messages; one-day-workshop for teachers. Families: school meeting; guided child-parent activities; newsletters. Local community: guided visits in grocery stores and local area as part of classroom curriculum; information sheets to sports-and youth clubs. The Boost study employed a cluster-randomised controlled study design and applied simple two-stage cluster sampling: A random sample of 10 municipalities followed by a random sample of 4 schools within each municipality (N = 40 schools). Schools were randomised into a total of 20 intervention-and 20 control schools. We included all year 7 pupils except those from school classes with special needs. Timeline: Baseline survey: August 2010. Delivery of intervention: September 2010-May 2011. First follow-up survey: May/June 2011. Second follow-up survey: May/June 2012. Primary outcome measures: Daily mean intake of fruit and vegetables and habitual fruit and vegetable intake measured by validated 24-hour recall-and food frequency questionnaires. Secondary outcome measures: determinants of fruit and vegetable intake, positive side-effects and unintended adverse effects. Implementation was monitored by thorough process evaluation. Discussion The baseline data file included 2,156 adolescents (95%). There was baseline equivalence

Solid state light source driver establishing buck or boost operation

Science.gov (United States)

Palmer, Fred

2017-08-29

A solid state light source driver circuit that operates in either a buck convertor or a boost convertor configuration is provided. The driver circuit includes a controller, a boost switch circuit and a buck switch circuit, each coupled to the controller, and a feedback circuit, coupled to the light source. The feedback circuit provides feedback to the controller, representing a DC output of the driver circuit. The controller controls the boost switch circuit and the buck switch circuit in response to the feedback signal, to regulate current to the light source. The controller places the driver circuit in its boost converter configuration when the DC output is less than a rectified AC voltage coupled to the driver circuit at an input node. The controller places the driver circuit in its buck converter configuration when the DC output is greater than the rectified AC voltage at the input node.

High-dose simultaneously integrated breast boost using intensity-modulated radiotherapy and inverse optimization

International Nuclear Information System (INIS)

Hurkmans, Coen W.; Meijer, Gert J.; Vliet-Vroegindeweij, Corine van; Sangen, Maurice J. van der; Cassee, Jorien

2006-01-01

Purpose: Recently a Phase III randomized trial has started comparing a boost of 16 Gy as part of whole-breast irradiation to a high boost of 26 Gy in young women. Our main aim was to develop an efficient simultaneously integrated boost (SIB) technique for the high-dose arm of the trial. Methods and Materials: Treatment planning was performed for 5 left-sided and 5 right-sided tumors. A tangential field intensity-modulated radiotherapy technique added to a sequentially planned 3-field boost (SEQ) was compared with a simultaneously planned technique (SIB) using inverse optimization. Normalized total dose (NTD)-corrected dose volume histogram parameters were calculated and compared. Results: The intended NTD was produced by 31 fractions of 1.66 Gy to the whole breast and 2.38 Gy to the boost volume. The average volume of the PTV-breast and PTV-boost receiving more than 95% of the prescribed dose was 97% or more for both techniques. Also, the mean lung dose and mean heart dose did not differ much between the techniques, with on average 3.5 Gy and 2.6 Gy for the SEQ and 3.8 Gy and 2.6 Gy for the SIB, respectively. However, the SIB resulted in a significantly more conformal irradiation of the PTV-boost. The volume of the PTV-breast, excluding the PTV-boost, receiving a dose higher than 95% of the boost dose could be reduced considerably using the SIB as compared with the SEQ from 129 cc (range, 48-262 cc) to 58 cc (range, 30-102 cc). Conclusions: A high-dose simultaneously integrated breast boost technique has been developed. The unwanted excessive dose to the breast was significantly reduced

Designing technology for emergent literacy: the PictoPal initiative

NARCIS (Netherlands)

McKenney, Susan; Voogt, Joke

2009-01-01

PictoPal is the name of a technology-supported intervention designed to foster the development of emergent reading and writing skills in four and five year old children. Following the theoretical underpinnings and a brief description of PictoPal, this article describes how children worked with the

Natural working fluids for solar-boosted heat pumps

Energy Technology Data Exchange (ETDEWEB)

Chaichana, C.; Lu Aye [University of Melbourne, Victoria (Australia). International Technologies Centre, Department of Civil and Environmental Engineering; Charters, W.W.S. [University of Melbourne, Victoria (Australia). Department of Mechanical and Manufacturing Engineering

2003-09-01

The option of using natural working fluids as a substitute of R-22 for solar-boosted heat pumps depends not only upon thermal performance and hazardous rating but also on potential impacts on the environment. This paper presents the comparative assessment of natural working fluids with R-22 in terms of their characteristics and thermophysical properties, and thermal performance. Some justification is given for using natural working fluids in a solar boosted heat pump water heater. The results show that R-744 is not suitable for solar-boosted heat pumps because of its low critical temperature and high operational pressures. On the other hand, R-717 seems to be a more appropriate substitute in terms of operational parameters and overall performance. However, major changes in the heat pumps are required. R-290 and R-1270 are identified as candidates for direct drop-in substitutes for R-22. (author)

A Zero Input Current Ripple ZVS/ZCS Boost Converter with Boundary-Mode Control

Directory of Open Access Journals (Sweden)

Ching-Ming Lai

2014-10-01

Full Text Available In this paper, in order to achieve zero ripple conditions, the use of a ripple mirror (RM circuit for the boost converter is proposed. The operation modes are studied and steady-state analyses performed to show the merits of the proposed converter. It is found that the proposed RM circuit technique can provide much better flexibility than the two-phase interleaved boost converter for locating the zero ripple operating point in the design stage. In addition, the choice of using a boundary-mode control is mainly based on the consideration of achieving both ZVS (zero voltage switching/ZCS (zero current switching soft-switching and constant on-time control for the converter. To verify the performance of the proposed converter, a 48 V input and 200 W/200 V output prototype is constructed. Experimental results verify the effectiveness of the proposed converter.

Modeling the peak of emergence in systems: Design and katachi.

Science.gov (United States)

Cardier, Beth; Goranson, H T; Casas, Niccolo; Lundberg, Patric; Erioli, Alessio; Takaki, Ryuji; Nagy, Dénes; Ciavarra, Richard; Sanford, Larry D

2017-12-01

It is difficult to model emergence in biological systems using reductionist paradigms. A requirement for computational modeling is that individual entities can be recorded parametrically and related logically, but their transformation into whole systems cannot be captured this way. The problem stems from an inability to formally represent the implicit influences that inform emergent organization, such as context, shifts in causal agency or scale, and self-reference. This lack hampers biological systems modeling and its computational counterpart, indicating a need for new fundamental abstraction frameworks that support system-level characteristics. We develop an approach that formally captures these characteristics, focusing on the way they come together to enable transformation at the 'peak' of the emergent process. An example from virology is presented, in which two seemingly antagonistic systems - the herpes cold sore virus and its host - are capable of altering their basic biological objectives to achieve a new equilibrium. The usual barriers to modeling this process are overcome by incorporating mechanisms from practices centered on its emergent peak: design and katachi. In the Japanese science of form, katachi refers to the emergence of intrinsic structure from real situations, where an optimal balance between implicit influences is achieved. Design indicates how such optimization is guided by principles of flow. These practices leverage qualities of situated abstraction, which we understand through the intuitive method of physicist Kôdi Husimi. Early results indicate that this approach can capture the functional transformations of biological emergence, whilst being reasonably computable. Due to its geometric foundations and narrative-based extension to logic, the method will also generate speculative predictions. This research forms the foundations of a new biomedical modeling platform, which is discussed. Copyright © 2017. Published by Elsevier Ltd.

The gradient boosting algorithm and random boosting for genome-assisted evaluation in large data sets.

Science.gov (United States)

González-Recio, O; Jiménez-Montero, J A; Alenda, R

2013-01-01

In the next few years, with the advent of high-density single nucleotide polymorphism (SNP) arrays and genome sequencing, genomic evaluation methods will need to deal with a large number of genetic variants and an increasing sample size. The boosting algorithm is a machine-learning technique that may alleviate the drawbacks of dealing with such large data sets. This algorithm combines different predictors in a sequential manner with some shrinkage on them; each predictor is applied consecutively to the residuals from the committee formed by the previous ones to form a final prediction based on a subset of covariates. Here, a detailed description is provided and examples using a toy data set are included. A modification of the algorithm called "random boosting" was proposed to increase predictive ability and decrease computation time of genome-assisted evaluation in large data sets. Random boosting uses a random selection of markers to add a subsequent weak learner to the predictive model. These modifications were applied to a real data set composed of 1,797 bulls genotyped for 39,714 SNP. Deregressed proofs of 4 yield traits and 1 type trait from January 2009 routine evaluations were used as dependent variables. A 2-fold cross-validation scenario was implemented. Sires born before 2005 were used as a training sample (1,576 and 1,562 for production and type traits, respectively), whereas younger sires were used as a testing sample to evaluate predictive ability of the algorithm on yet-to-be-observed phenotypes. Comparison with the original algorithm was provided. The predictive ability of the algorithm was measured as Pearson correlations between observed and predicted responses. Further, estimated bias was computed as the average difference between observed and predicted phenotypes. The results showed that the modification of the original boosting algorithm could be run in 1% of the time used with the original algorithm and with negligible differences in accuracy

Intensity modulated radiotherapy with simultaneous integrated boost vs. conventional radiotherapy with sequential boost for breast cancer - A preliminary result.

Science.gov (United States)

Lee, Hsin-Hua; Hou, Ming-Feng; Chuang, Hung-Yi; Huang, Ming-Yii; Tsuei, Le-Ping; Chen, Fang-Ming; Ou-Yang, Fu; Huang, Chih-Jen

2015-10-01

This study was aimed to assess the acute dermatological adverse effect from two distinct RT techniques for breast cancer patients. We compared intensity-modulated radiotherapy with simultaneous integrated boost (IMRT-SIB) and conventional radiotherapy followed by sequential boost (CRT-SB). The study population was composed of 126 consecutive female breast cancer patients treated with breast conserving surgery. Sixty-six patients received IMRT-SIB to 2 dose levels simultaneously. They received 50.4 Gy at 1.8 Gy per fraction to the whole breast and 60.2 Gy at 2.15 Gy per fraction to the tumor bed by integral boost. Sixty patients in the CRT-SB group received 50 Gy in 25 fractions to the whole breast followed by a boost irradiation to tumor bed in 5-7 fractions to a total dose of 60-64 Gy. Acute skin toxicities were documented in agreement with the Common Terminology Criteria for Adverse Events version 3 (CTCAE v.3.0). Ninety-eight patients had grade 1 radiation dermatitis while 14 patients had grade 2. Among those with grade 2, there were 3 patients in IMRT-SIB group (4.5%) while 11 in CRT-SB group (18.3%). (P = 0.048) There was no patient with higher than grade 2 toxicity. Three year local control was 99.2%, 3-year disease free survival was 97.5% and 3-year overall survival was 99.2%. A significant reduction in the severity of acute radiation dermatitis from IMRT-SIB comparing with CRT-SB is demonstrated. Copyright © 2015 Elsevier Ltd. All rights reserved.

Boosted dark matter signals uplifted with self-interaction

OpenAIRE

Kong, Kyoungchul; Mohlabeng, Gopolang; Park, Jong-Chul

2018-01-01

We explore detection prospects of a non-standard dark sector in the context of boosted dark matter. We focus on a scenario with two dark matter particles of a large mass difference, where the heavier candidate is secluded and interacts with the standard model particles only at loops, escaping existing direct and indirect detection bounds. Yet its pair annihilation in the galactic center or in the Sun may produce boosted stable particles, which could be detected as visible Cherenkov light in l...

Searches with Boosted Objects at ATLAS and CMS

CERN Document Server

Behr, K; The ATLAS collaboration

2014-01-01

This talk presents an overview of searches for new physics in boosted final states conducted by the ATLAS and CMS experiments during Run-I of the LHC. An emphasis is put on techniques for the reconstruction and identification of both hadronic and leptonic decays of objects with large transverse momenta: Various substructure and grooming techniques as well as modified lepton isolation criteria are reviewed and their use in the most common algorithms for boosted top and boson tagging is discussed.

Security Implications of Physical Design Attributes in the Emergency Department.

Science.gov (United States)

Pati, Debajyoti; Pati, Sipra; Harvey, Thomas E

2016-07-01

Security, a subset of safety, is equally important in the efficient delivery of patient care. The emergency department (ED) is susceptible to violence creating concerns for the safety and security of patients, staff, and visitors and for the safe and efficient delivery of care. Although there is an implicit and growing recognition of the role of the physical environment, interventions typically have been at the microlevel. The objective of this study was to identify physical design attributes that potentially influence safety and efficiency of ED operations. An exploratory, qualitative research design was adopted to examine the efficiency and safety correlates of ED physical design attributes. The study comprised a multimeasure approach involving multidisciplinary gaming, semistructured interviews, and touring interviews of frontline staff in four EDs at three hospital systems across three states. Five macro physical design attributes (issues that need to be addressed at the design stage and expensive to rectify once built) emerged from the data as factors substantially associated with security issues. They are design issues pertaining to (a) the entry zone, (b) traffic management, (c) patient room clustering, (d) centralization versus decentralization, and (e) provisions for special populations. Data from this study suggest that ED security concerns are generally associated with three sources: (a) gang-related violence, (b) dissatisfied patients, and (c) behavioral health patients. Study data show that physical design has an important role in addressing the above-mentioned concerns. Implications for ED design are outlined in the article. © The Author(s) 2016.

Impact of the Radiation Boost on Outcomes After Breast-Conserving Surgery and Radiation

International Nuclear Information System (INIS)

Murphy, Colin; Anderson, Penny R.; Li Tianyu; Bleicher, Richard J.; Sigurdson, Elin R.; Goldstein, Lori J.; Swaby, Ramona; Denlinger, Crystal; Dushkin, Holly; Nicolaou, Nicos; Freedman, Gary M.

2011-01-01

Purpose: We examined the impact of radiation tumor bed boost parameters in early-stage breast cancer on local control and cosmetic outcomes. Methods and Materials: A total of 3,186 women underwent postlumpectomy whole-breast radiation with a tumor bed boost for Tis to T2 breast cancer from 1970 to 2008. Boost parameters analyzed included size, energy, dose, and technique. Endpoints were local control, cosmesis, and fibrosis. The Kaplan-Meier method was used to estimate actuarial incidence, and a Cox proportional hazard model was used to determine independent predictors of outcomes on multivariate analysis (MVA). The median follow-up was 78 months (range, 1-305 months). Results: The crude cosmetic results were excellent in 54%, good in 41%, and fair/poor in 5% of patients. The 10-year estimate of an excellent cosmesis was 66%. On MVA, independent predictors for excellent cosmesis were use of electron boost, lower electron energy, adjuvant systemic therapy, and whole-breast IMRT. Fibrosis was reported in 8.4% of patients. The actuarial incidence of fibrosis was 11% at 5 years and 17% at 10 years. On MVA, independent predictors of fibrosis were larger cup size and higher boost energy. The 10-year actuarial local failure was 6.3%. There was no significant difference in local control by boost method, cut-out size, dose, or energy. Conclusions: Likelihood of excellent cosmesis or fibrosis are associated with boost technique, electron energy, and cup size. However, because of high local control and rare incidence of fair/poor cosmesis with a boost, the anatomy of the patient and tumor cavity should ultimately determine the necessary boost parameters.

Design for Manufacture and Assembly for Product Development (Case study : Emergency Lamp)

Science.gov (United States)

Ngatilah, Y.; Pulansari, F.; Ernawati, Dira; Pujiastuti, C.; Parwati, C. I.; Prasetyo, B.

2018-01-01

Community needs that are not primary but important in everyday life are lights for lighting. State electricity company (PLN) is experiencing limitations in supplying electricity for this puIDRose. Therefore emergency lights (emergency lights) are already marketed in the community, which limited function only illuminate a very limited space. Therefore we developed the design of energy saving lamps using “Light Emitting Diode” (LED) which can illuminate the whole house as well as functioning as mobile phone charger (HP). The method used is Design for Manufacture and Assembly (DFMA), with the result of design development The percentage increase in assembly efficiency (E) is 0.01071 - 0.00645 = 0.00426 or = 39.76%. The decrease in material costs is IDR 234,000 - IDR 214,000 = IDR 20,000 or = 8.54% .Development design is received because of more assembly efficiency than the initial design. Power usage on previous products with series and designs of the original product can last only 4-5 hours non-stop, while the development of the design can survive 9-10 hours 2x more energy efficient.

SMART STRATEGY TO BOOST STUDENTS’ READING COMPREHENSION

Directory of Open Access Journals (Sweden)

Muhammad Lukman Syafi’i

2015-05-01

Full Text Available Reading as one of language skills plays significant roles in the teaching English as a foreign language. Since the teacher still uses the conventional way to teach reading, students‘ ability in reading comprehension seems still unsatisfactory yet. So, teacher should explore and develop new strategies. One of strategies in reading comprehension that can trigger our students to attain that purpose is SMART (Self Monitoring Approach for Reading and Thinking strategy. This study is developing SMART strategy to boost the reading comprehension achievement of the ninth grade students. The research applies a collaborative classroom action research design in which the researcher and the collaborative teacher work together in preparing a suitable procedure of SMART strategy, designing the lesson plan, determining the criteria of success, implementing the action, observing, and doing reflection. The finding indicated that SMART strategy was successful to enhance students‘ motivation to be actively involved in the instructional process. The improvement on the students‘ participation was 75% in Cycle 1 and 87% in Cycle 2.

Boosting instance prototypes to detect local dermoscopic features.

Science.gov (United States)

Situ, Ning; Yuan, Xiaojing; Zouridakis, George

2010-01-01

Local dermoscopic features are useful in many dermoscopic criteria for skin cancer detection. We address the problem of detecting local dermoscopic features from epiluminescence (ELM) microscopy skin lesion images. We formulate the recognition of local dermoscopic features as a multi-instance learning (MIL) problem. We employ the method of diverse density (DD) and evidence confidence (EC) function to convert MIL to a single-instance learning (SIL) problem. We apply Adaboost to improve the classification performance with support vector machines (SVMs) as the base classifier. We also propose to boost the selection of instance prototypes through changing the data weights in the DD function. We validate the methods on detecting ten local dermoscopic features from a dataset with 360 images. We compare the performance of the MIL approach, its boosting version, and a baseline method without using MIL. Our results show that boosting can provide performance improvement compared to the other two methods.

Emergent Bilingualism and Working Memory Development in School Aged Children

Science.gov (United States)

Hansen, Laura Birke; Macizo, Pedro; Duñabeitia, Jon Andoni; Saldaña, David; Carreiras, Manuel; Fuentes, Luis J.; Bajo, M. Teresa

2016-01-01

The present research explores working memory (WM) development in monolingual as well as emergent bilingual children immersed in an L2 at school. Evidence from recent years suggests that bilingualism may boost domain-general executive control, but impair nonexecutive linguistic processing. Both are relevant for verbal WM, but different paradigms…

Is there room for combined modality treatments? Dosimetric comparison of boost strategies for advanced head and neck and prostate cancer

International Nuclear Information System (INIS)

Gora, Joanna; Hopfgartner, Johannes; Kuess, Peter; Paskeviciute, Brigita; Georg, Dietmar

2013-01-01

The purpose of the study was to determine the dosimetric difference between three emerging treatment modalities-volumetric-modulated arc therapy (VMAT), intensity-modulated proton beam therapy (IMPT) and intensity-modulated carbon ion beam therapy (IMIT)-for two tumour sites where selective boosting of the tumour is applied. For 10 patients with locally advanced head and neck (H and N) cancer and 10 with high-risk prostate cancer (PC) a VMAT plan was generated for PTV initial that included lymph node regions, delivering 50 Gy (IsoE) for H and N and 50.4 Gy (IsoE) for PC patients. Furthermore, separate boost plans (VMAT, IMPT and IMIT) were created to boost PTV boost up to 70 Gy (IsoE) and 78 Gy (IsoE) for H and N and PC cases, respectively. Doses to brainstem, myelon, larynx and parotid glands were assessed for H and N cases. Additionally, various organs at risk (OARs) (e.g. cochlea, middle ear, masticator space) were evaluated that are currently discussed with respect to quality of life after treatment. For PC cases, bladder, rectum and femoral heads were considered as OARs. For both tumour sites target goals were easily met. Looking at OAR sparing, generally VMAT + VMAT was worst. VMAT + IMIT had the potential to spare some structures in very close target vicinity (such as cochlea, middle ear, masticator space) significantly better than VMAT + IMPT. Mean doses for rectal and bladder wall were on average 4 Gy (IsoE) and 1.5 Gy (IsoE) higher, respectively, compared to photons plus particles scenarios. Similar results were found for parotid glands and larynx. Concerning target coverage, no significant differences were observed between the three treatment concepts. Clear dosimetric benefits were observed for particle beam therapy as boost modality. However, the clinical benefit of combined modality treatments remains to be demonstrated. (author)

StentBoost Visualization for the Evaluation of Coronary Stent Expansion During Percutaneous Coronary Interventions

OpenAIRE

Cura, Fernando; Albertal, Mariano; Candiello, Alfonsina; Nau, Gerardo; Bonvini, Victor; Tricherri, Hernan; Padilla, Lucio T.; Belardi, Jorge A.

2013-01-01

Introduction Inadequate stent implantation is associated with stent thrombosis and restenosis. StentBoost can enhance stent visualization and evaluate stent expansion. Currently, there are limited comparison studies between StentBoost and intravascular ultrasound (IVUS). We aimed to test the correlation and agreement between IVUS and StentBoost measurements. Methods From December 2010 to December 2011, 38 patients (54 stents) were analyzed using IVUS and StentBoost. Minimal stent diameter and...

FULL ELECTROMAGNETIC FEL SIMULATION VIA THE LORENTZ-BOOSTED FRAME TRANSFORMATION

International Nuclear Information System (INIS)

Fawley, William; Vay, Jean-Luc

2010-01-01

Numerical electromagnetic simulation of some systems containing charged particles with highly relativistic directed motion can by speeded up by orders of magnitude by choice of the proper Lorentz-boosted frame. A particularly good application for calculation in a boosted frame isthat of short wavelength free-electron lasers (FELs) where a high energy electron beam with small fractional energy spread interacts with a static magnetic undulator. In the optimal boost frame (i.e., the ponderomotive rest frame), the red-shifted FEL radiation and blue-shifted undulator field have identical wavelengths and the number of required longitudinal grid cells and time-steps for fully electromagnetic simulation (relative to the laboratory frame) decrease by factors of gamma 2 each. In theory, boosted frame EM codes permit direct study of FEL problems for which the eikonal approximation for propagation of the radiation field and wiggler-period-averaging for the particle-field interaction may be suspect. We have adapted the WARP code to apply this method to several electromagnetic FEL problems including spontaneous emission, strong exponential gain in a seeded, single pass amplifier configuration, and emission from e-beams in undulators with multiple harmonic components. WARP has a standard relativistic macroparticle mover and a fully 3-D electromagnetic field solver. We discuss our boosted frame results and compare with those obtained using the 'standard' eikonal FEL simulation approach.

Higgs boson creation in laser-boosted lepton collisions

International Nuclear Information System (INIS)

Müller, Sarah J.; Keitel, Christoph H.; Müller, Carsten

2014-01-01

Electroweak processes in high-energy lepton collisions are considered in a situation where the incident center-of-mass energy lies below the reaction threshold, but is boosted to the required level by subsequent laser acceleration. Within the framework of laser-dressed quantum field theory, we study the laser-boosted process ℓ + ℓ − →HZ 0 in detail and specify the technical demands needed for its experimental realization. Further, we outline possible qualitative differences to field-free processes regarding the detection of the produced Higgs bosons.

Multiclass Boosting with Adaptive Group-Based kNN and Its Application in Text Categorization

Directory of Open Access Journals (Sweden)

Lei La

2012-01-01

Full Text Available AdaBoost is an excellent committee-based tool for classification. However, its effectiveness and efficiency in multiclass categorization face the challenges from methods based on support vector machine (SVM, neural networks (NN, naïve Bayes, and k-nearest neighbor (kNN. This paper uses a novel multi-class AdaBoost algorithm to avoid reducing the multi-class classification problem to multiple two-class classification problems. This novel method is more effective. In addition, it keeps the accuracy advantage of existing AdaBoost. An adaptive group-based kNN method is proposed in this paper to build more accurate weak classifiers and in this way control the number of basis classifiers in an acceptable range. To further enhance the performance, weak classifiers are combined into a strong classifier through a double iterative weighted way and construct an adaptive group-based kNN boosting algorithm (AGkNN-AdaBoost. We implement AGkNN-AdaBoost in a Chinese text categorization system. Experimental results showed that the classification algorithm proposed in this paper has better performance both in precision and recall than many other text categorization methods including traditional AdaBoost. In addition, the processing speed is significantly enhanced than original AdaBoost and many other classic categorization algorithms.

Cascaded H-Bridge with Bidirectional Boost Converters for Energy Storage

DEFF Research Database (Denmark)

Trintis, Ionut; Munk-Nielsen, Stig; Teodorescu, Remus

2011-01-01

This paper presents the design and control of a cascaded H-bridge converter for energy storage with bidirectional boost converter as charge/discharge unit. The disadvantage of the second harmonic on the main energy storage unit as well as its voltage variation with the state of charge is solved...... by this structure. The independent phase grid control is proposed for this topology. This strategy is able to control the average dc-link voltage for each phase independently and to balance the cells capacitors voltages. The balance of the energy storage units is achieved by controlling independently each cell...

Designing a clinical dashboard to fill information gaps in the emergency department.

Science.gov (United States)

Swartz, Jordan L; Cimino, James J; Fred, Matthew R; Green, Robert A; Vawdrey, David K

2014-01-01

Data fragmentation within electronic health records causes gaps in the information readily available to clinicians. We investigated the information needs of emergency medicine clinicians in order to design an electronic dashboard to fill information gaps in the emergency department. An online survey was distributed to all emergency medicine physicians at a large, urban academic medical center. The survey response rate was 48% (52/109). The clinical information items reported to be most helpful while caring for patients in the emergency department were vital signs, electrocardiogram (ECG) reports, previous discharge summaries, and previous lab results. Brief structured interviews were also conducted with 18 clinicians during their shifts in the emergency department. From the interviews, three themes emerged: 1) difficulty accessing vital signs, 2) difficulty accessing point-of-care tests, and 3) difficulty comparing the current ECG with the previous ECG. An emergency medicine clinical dashboard was developed to address these difficulties.

Designing a data-driven decision support tool for nurse scheduling in the emergency department: a case study of a southern New Jersey emergency department.

Science.gov (United States)

Otegbeye, Mojisola; Scriber, Roslyn; Ducoin, Donna; Glasofer, Amy

2015-01-01

A health system serving Burlington and Camden Counties, New Jersey, sought to improve labor productivity for its emergency departments, with emphasis on optimizing nursing staff schedules. Using historical emergency department visit data and operating constraints, a decision support tool was designed to recommend the number of emergency nurses needed in each hour for each day of the week. The pilot emergency department nurse managers used the decision support tool's recommendations to redeploy nurse hours from weekends into a float pool to support periods of demand spikes on weekdays. Productivity improved significantly, with no unfavorable impact on patient throughput, and patient and staff satisfaction. Today's emergency department manager can leverage the increasing ease of access to the emergency department information system's data repository to successfully design a simple but effective tool to support the alignment of its nursing schedule with demand patterns. Copyright © 2015 Emergency Nurses Association. Published by Elsevier Inc. All rights reserved.

Design exploration of emerging nano-scale non-volatile memory

CERN Document Server

Yu, Hao

2014-01-01

This book presents the latest techniques for characterization, modeling and design for nano-scale non-volatile memory (NVM) devices.  Coverage focuses on fundamental NVM device fabrication and characterization, internal state identification of memristic dynamics with physics modeling, NVM circuit design, and hybrid NVM memory system design-space optimization. The authors discuss design methodologies for nano-scale NVM devices from a circuits/systems perspective, including the general foundations for the fundamental memristic dynamics in NVM devices.  Coverage includes physical modeling, as well as the development of a platform to explore novel hybrid CMOS and NVM circuit and system design.   • Offers readers a systematic and comprehensive treatment of emerging nano-scale non-volatile memory (NVM) devices; • Focuses on the internal state of NVM memristic dynamics, novel NVM readout and memory cell circuit design, and hybrid NVM memory system optimization; • Provides both theoretical analysis and pr...

Merging art and design in foresight: Making sense of Emerge

DEFF Research Database (Denmark)

Selin, Cynthia Lea

2015-01-01

Emerge: Artists and Scientists Redesign the Future, hosted by Arizona State University in 2012, united artists, engineers, bioscientists, social scientists, storytellers and designers to build, draw, write and play with the future. Over three days, and in nine different workshops, participants cr...

Experimental Treatment for Duchenne Muscular Dystrophy Gets Boost from Existing Medication

Science.gov (United States)

... Boost from Existing Medication Spotlight on Research Experimental Treatment for Duchenne Muscular Dystrophy Gets Boost from Existing Medication By Colleen Labbe, M.S. | March 1, 2013 A mouse hanging on a wire during a test of muscle strength. Mice with a mutant dystrophin gene, which ...

Modelling, simulation and construction of a dc/dc boost power converter: a school experimental system

International Nuclear Information System (INIS)

Silva-Ortigoza, R; Marciano-Melchor, M; Silva-Ortigoza, G; Hernández-Guzmán, V M; Saldaña-González, G; Marcelino-Aranda, M

2012-01-01

We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders the feasible introduction of this equipment in undergraduate laboratories. (paper)

Designing Science Learning Environments That Support Emerging Bilingual Students to Problematize Electrical Phenomena

Science.gov (United States)

Suarez, Enrique A.

This dissertation investigates how emerging bilingual students make sense of natural phenomena through engaging in certain epistemic practices of science, and the elements of the learning environment that created those opportunities. Specifically, the dissertation focuses on how emerging bilingual students problematized electrical phenomena, like electric flow and electrical resistance, and how the design features of the environment (e.g., sequencing of activities, linguistic practices) may have supported students as they made sense of phenomena. The first study describes how for students presented and evaluated mechanistic models of electric flow, focusing specifically on how students identified and negotiated a disagreement between their explanatory models. The results from this study highlight the complexity of students' disagreements, not only because of the epistemological aspects related to presenting and evaluating knowledge, but also due to interpersonal dynamics and the discomfort associated with disagreeing with another person. The second study focuses on the design features of the learning environment that supported emerging bilingual students' investigations of electrical phenomena. The findings from this study highlight how a carefully designed set of activities, with the appropriate material resources (e.g., experimental tools), could support students to problematize electrical resistance. The third study describes how emerging bilingual students engaged in translanguaging practices and the contextual features of the learning environment that created and hindered opportunities for translanguaging. The findings from this study identify and articulate how emerging bilingual students engaged in translanguaging practices when problematizing electrical resistance, and strengthen the perspective that, in order to be equitable for emerging bilingual students, science learning environments need to act as translanguaging spaces. This dissertation makes three

Single Phase Transformer-less Buck-Boost Inverter with Zero Leakage Current for PV Systems

DEFF Research Database (Denmark)

Mostaan, Ali; Abdelhakim, Ahmed; N. Soltani, Mohsen

2017-01-01

In this paper, a novel single-stage single-phase transformer-less buck-boost inverter is proposed, in which a reduced number of passive components is used. The proposed inverter combines the conventional buck, boost, and buck-boost converters in one converter in order to obtain a sinusoidal output...

Balanced G-band Gm-boosted frequency doublers in transferred substrate InP HBT technology

DEFF Research Database (Denmark)

Johansen, Tom Keinicke; Thualfiqar, Al-Sawaf; Weimann, Nils

2016-01-01

In this paper, balanced G-band Gm-boosted frequency doublers in transferred substrate (TS) InP HBT technology are reported for the first time. The Gm-boosted frequency doublers consist of a phase compensated Marchand balun, Gm-boosted doubler stage, and an optional cascode gain stage at the outpu...

Generalized Switched-Inductor Based Buck-Boost Z-H Converter

Directory of Open Access Journals (Sweden)

E. Babaei

2017-12-01

Full Text Available In this paper, a generalized buck-boost Z-H converter based on switched inductors is proposed. This structure consists of a set of series connected switched-inductor cells. The voltage conversion ratio of the proposed structure is adjusted by changing the number of cells and the duty cycle. Like the conventional Z-H converter, the shoot-through switching state and the diode before LC network are eliminated. The proposed converter can provide high voltage gain in low duty cycles. Considering different values for duty cycle, the proposed structure works in two operating zones. In the first operating zone, it works as a buck-boost converter and in the second operating zone, it works as a boost converter. In this paper, a complete analysis of the proposed converter is presented. In order to confirm the accuracy of mathematic calculations, the simulations results by using PSCAD/EMTDC software are given.

The Boost study: Design of a school- and community-based randomised trial to promote fruit and vegetable consumption among teenagers

DEFF Research Database (Denmark)

Krølner, Rikke; Suldrup Jørgensen, Thea; Aarestrup, Anne Kristine

2012-01-01

The aim of the Boost study was to produce a persistent increase in fruit and vegetable consumption among 13-year-olds. This paper describes the development, implementation and evaluation of a school-and community-based, multi-component intervention guided by theory, evidence, and best practice....

Brachytherapy boost for breast cancer: what do we know? where do we go?

International Nuclear Information System (INIS)

Hannoun-Levi, J.M.; Marsiglia, H.

2004-01-01

Since many years, Brachytherapy (BT) appears to play an important role in the treatment of many solid tumors. For breast cancer, BT is usually used as boost after postoperative external beam radiation therapy. In certain circumstances. BT can be used as sole radiation technique focalized on the tumor bed or more rarely, as second conservative treatment in case of local recurrence for woman refusing salvage mastectomy. Boost BT is most often applied via an interstitial technique while the dose rate can vary from low to high close rate through pulse dose rate. All of those boost techniques were published and some of them compared the results obtained with BT and external beam electron therapy. The analysis of the published phase II and III trials was not able to show significant differences between the two boost techniques in term of local control as well as late skin side effects. However, we noted that the patients who received BT boost presented a higher risk of local recurrence compare to those treated with electron therapy, due to age, margin status or presence of extensive intraductal component. Only a phase III trial randomizing BT boost vs electron therapy boost could show a possible improvement of local control rate in the BT arm; however, this trial should enroll patients with a real high risk of local recurrence in order to take benefit from the dosimetric advantages of BT. (author)

Emergency control room design of a nuclear reactor used to produce radioisotope

Energy Technology Data Exchange (ETDEWEB)

Santos, Isaac J.A.L. dos; Farias, Larissa P. de; Ponte, Luana T.L.; Goncalves, Gabriel L.; Castro, Heraclito M.; Farias, Marcos S.; Carvalho, Paulo V.R. de; Vianna Filho, Alfredo M.V., E-mail: luquetti@ien.gov.br [Instituto Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Departamento Engenharia Nuclear

2015-07-01

A control room is defined as a functional entity with an associated physical structure, where the operators carry out the centralized control, monitoring and administrative responsibilities. Emergency control room acts as an alternative control room for the purpose of shutting down or maintaining the facility in a safe shutdown state when the main control room is uninhabitable. The mission of emergency control room is to provide the resources to bring the plant to a safe shutdown condition after an evacuation of the main control room. An evacuation of the main control room is assumed when there is no possibility to accomplish tasks involved in the shutdown except reactor trip. The purpose of this paper is to present a specific approach for the design of the emergency control room of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards and the participation of a multidisciplinary team in the development phase of the design. Using the information gathered from standards and from the multidisciplinary team a 3D Sketch and a 3D printing of the emergency control room were created. (author)

Emergency control room design of a nuclear reactor used to produce radioisotope

International Nuclear Information System (INIS)

Santos, Isaac J.A.L. dos; Farias, Larissa P. de; Ponte, Luana T.L.; Goncalves, Gabriel L.; Castro, Heraclito M.; Farias, Marcos S.; Carvalho, Paulo V.R. de; Vianna Filho, Alfredo M.V.

2015-01-01

A control room is defined as a functional entity with an associated physical structure, where the operators carry out the centralized control, monitoring and administrative responsibilities. Emergency control room acts as an alternative control room for the purpose of shutting down or maintaining the facility in a safe shutdown state when the main control room is uninhabitable. The mission of emergency control room is to provide the resources to bring the plant to a safe shutdown condition after an evacuation of the main control room. An evacuation of the main control room is assumed when there is no possibility to accomplish tasks involved in the shutdown except reactor trip. The purpose of this paper is to present a specific approach for the design of the emergency control room of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards and the participation of a multidisciplinary team in the development phase of the design. Using the information gathered from standards and from the multidisciplinary team a 3D Sketch and a 3D printing of the emergency control room were created. (author)

Estimation of age-specific rates of reactivation and immune boosting of the varicella zoster virus

Directory of Open Access Journals (Sweden)

Isabella Marinelli

2017-06-01

Full Text Available Studies into the impact of vaccination against the varicella zoster virus (VZV have increasingly focused on herpes zoster (HZ, which is believed to be increasing in vaccinated populations with decreasing infection pressure. This idea can be traced back to Hope-Simpson's hypothesis, in which a person's immune status determines the likelihood that he/she will develop HZ. Immunity decreases over time, and can be boosted by contact with a person experiencing varicella (exogenous boosting or by a reactivation attempt of the virus (endogenous boosting. Here we use transmission models to estimate age-specific rates of reactivation and immune boosting, exogenous as well as endogenous, using zoster incidence data from the Netherlands (2002–2011, n = 7026. The boosting and reactivation rates are estimated with splines, enabling these quantities to be optimally informed by the data. The analyses show that models with high levels of exogenous boosting and estimated or zero endogenous boosting, constant rate of loss of immunity, and reactivation rate increasing with age (to more than 5% per year in the elderly give the best fit to the data. Estimates of the rates of immune boosting and reactivation are strongly correlated. This has important implications as these parameters determine the fraction of the population with waned immunity. We conclude that independent evidence on rates of immune boosting and reactivation in persons with waned immunity are needed to robustly predict the impact of varicella vaccination on the incidence of HZ.

Breast conserving treatment for breast cancer: dosimetric comparison of sequential versus simultaneous integrated photon boost.

Science.gov (United States)

Van Parijs, Hilde; Reynders, Truus; Heuninckx, Karina; Verellen, Dirk; Storme, Guy; De Ridder, Mark

2014-01-01

Breast conserving surgery followed by whole breast irradiation is widely accepted as standard of care for early breast cancer. Addition of a boost dose to the initial tumor area further reduces local recurrences. We investigated the dosimetric benefits of a simultaneously integrated boost (SIB) compared to a sequential boost to hypofractionate the boost volume, while maintaining normofractionation on the breast. For 10 patients 4 treatment plans were deployed, 1 with a sequential photon boost, and 3 with different SIB techniques: on a conventional linear accelerator, helical TomoTherapy, and static TomoDirect. Dosimetric comparison was performed. PTV-coverage was good in all techniques. Conformity was better with all SIB techniques compared to sequential boost (P = 0.0001). There was less dose spilling to the ipsilateral breast outside the PTVboost (P = 0.04). The dose to the organs at risk (OAR) was not influenced by SIB compared to sequential boost. Helical TomoTherapy showed a higher mean dose to the contralateral breast, but less than 5 Gy for each patient. SIB showed less dose spilling within the breast and equal dose to OAR compared to sequential boost. Both helical TomoTherapy and the conventional technique delivered acceptable dosimetry. SIB seems a safe alternative and can be implemented in clinical routine.

Targeted intraoperative radiotherapy tumour bed boost during breast-conserving surgery after neoadjuvant chemotherapy

Energy Technology Data Exchange (ETDEWEB)

Kolberg, Hans-Christian; Akpolat-Basci, Leyla; Stephanou, Miltiades [Marienhospital Bottrop gGmbH, Department of Gynecology and Obstetrics, Bottrop (Germany); Loevey, Gyoergy [BORAD, Bottrop (Germany); Fasching, Peter A. [University of Erlangen, Erlangen (Germany); Untch, Michael [Helios Klinikum Berlin-Buch, Berlin (Germany); Liedtke, Cornelia [University Hospital Schleswig-Holstein/Campus Luebeck, Luebeck (Germany); Bulsara, Max [University of Notre Dame, Fremantle (Australia); University College, London (United Kingdom); Vaidya, Jayant S. [University College, London (United Kingdom)

2017-01-15

The use of targeted intraoperative radiotherapy (TARGIT-IORT) as a tumour bed boost during breast-conserving surgery (BCS) for breast cancer has been reported since 1998. We present its use in patients undergoing breast conservation following neoadjuvant therapy (NACT). In this retrospective study involving 116 patients after NACT we compared outcomes of 61 patients who received a tumour bed boost with IORT during lumpectomy versus 55 patients treated in the previous 13 months with external (EBRT) boost. All patients received whole breast radiotherapy. Local recurrence-free survival (LRFS), disease-free survival (DFS), distant disease-free survival (DDFS), breast cancer mortality (BCM), non-breast cancer mortality (NBCM) and overall mortality (OS) were compared. Median follow up was 49 months. The differences in LRFS, DFS and BCM were not statistically significant. The 5-year Kaplan-Meier estimate of OS was significantly better by 15% with IORT: IORT 2 events (96.7%, 95%CI 87.5-99.2), EBRT 9 events (81.7%, 95%CI 67.6-90.1), hazard ratio (HR) 0.19 (0.04-0.87), log rank p = 0.016, mainly due to a reduction of 10.1% in NBCM: IORT 100%, EBRT 89.9% (77.3-95.7), HR (not calculable), log rank p = 0.015. The DDFS was as follows: IORT 3 events (95.1%, 85.5-98.4), EBRT 12 events (69.0%, 49.1-82.4), HR 0.23 (0.06-0.80), log rank p = 0.012. IORT during lumpectomy after neoadjuvant chemotherapy as a tumour bed boost appears to give results that are not worse than external beam radiotherapy boost. These data give further support to the inclusion of such patients in the TARGIT-B (boost) randomised trial that is testing whether IORT boost is superior to EBRT boost. (orig.) [German] Die intraoperative Radiotherapie (TARGIT-IORT) als vorgezogener Boost im Rahmen der brusterhaltenden Therapie (BET) ist seit 1998 Gegenstand der wissenschaftlichen Diskussion. Wir praesentieren Daten zum Einsatz der IORT bei der BET nach neoadjuvanter Therapie (NACT). In diese retrospektive Analyse

A Novel Single Switch Transformerless Quadratic DC/DC Buck-Boost Converter

DEFF Research Database (Denmark)

Mostaan, Ali; A. Gorji, Saman; N. Soltani, Mohsen

2017-01-01

A novel quadratic buck-boost DC/DC converter is presented in this study. The proposed converter utilizes only one active switch and can step-up/down the input voltage, while the existing single switch quadratic buck/boost converters can only work in step-up or step-down mode. First, the proposed ...

Estimation of reliability of a interleaving PFC boost converter

Directory of Open Access Journals (Sweden)

Gulam Amer Sandepudi

2010-01-01

Full Text Available Reliability plays an important role in power supplies. For other electronic equipment, a certain failure mode, at least for a part of the total system, can often be employed without serious (critical effects. However, for power supply no such condition can be accepted, since very high demands on its reliability must be achieved. At higher power levels, the continuous conduction mode (CCM boost converter is preferred topology for implementation a front end with PFC. As a result, significant efforts have been made to improve the performance of high boost converter. This paper is one of the efforts for improving the performance of the converter from the reliability point of view. In this paper, interleaving boost power factor correction converter is simulated with single switch in continuous conduction mode (CCM, discontinuous conduction mode (DCM and critical conduction mode (CRM under different output power ratings. Results of the converter are explored from reliability point of view.

Boosted Jet Tagging with Jet-Images and Deep Neural Networks

International Nuclear Information System (INIS)

Kagan, Michael; Oliveira, Luke de; Mackey, Lester; Nachman, Benjamin; Schwartzman, Ariel

2016-01-01

Building on the jet-image based representation of high energy jets, we develop computer vision based techniques for jet tagging through the use of deep neural networks. Jet-images enabled the connection between jet substructure and tagging with the fields of computer vision and image processing. We show how applying such techniques using deep neural networks can improve the performance to identify highly boosted W bosons with respect to state-of-the-art substructure methods. In addition, we explore new ways to extract and visualize the discriminating features of different classes of jets, adding a new capability to understand the physics within jets and to design more powerful jet tagging methods

Heterologous Prime-Boost Immunizations with a Virosomal and an Alphavirus Replicon Vaccine

NARCIS (Netherlands)

Walczak, Mateusz; de Mare, Arjan; Riezebos-Brilman, Annelies; Regts, Joke; Hoogeboom, Baukje-Nynke; Visser, Jeroen T.; Fiedler, Marc; Jansen-Duerr, Pidder; van der Zee, Ate G. J.; Nijman, Hans W.; Wilschut, Jan; Daemen, Toos

2011-01-01

Heterologous prime-boost immunization strategies in general establish higher frequencies of antigen-specific T lymphocytes than homologous prime-boost protocols or single immunizations. We developed virosomes and recombinant Semliki Forest virus (rSFV) as antigen delivery systems, each capable of

The emergency braking module for an electronic copilot design and first results

Energy Technology Data Exchange (ETDEWEB)

Ameling, C.; Kirchner, A. [Univ. of the Federal Armed Forces Hamburg (Germany). Dept. of Mechanical Engineering

2000-07-01

This paper deals with design and development of an emergency braking module for an electronic copilot (ECP). ECP is used within an autonomous vehicle as a partial redundant system for vehicle control. ECP receives the necessary information about the positions and relative velocities of obstacles from various sources such as laserscanner or vision sensors. In the current stage of development the emergency breaking module computes, whether an object collides with the front of the vehicle. If the time-to-collision falls below the braking capacity an emergency braking is triggered. Experimental results show the capabilities of the system. (orig.)

Breast Conserving Treatment for Breast Cancer: Dosimetric Comparison of Sequential versus Simultaneous Integrated Photon Boost

Directory of Open Access Journals (Sweden)

Hilde Van Parijs

2014-01-01

Full Text Available Background. Breast conserving surgery followed by whole breast irradiation is widely accepted as standard of care for early breast cancer. Addition of a boost dose to the initial tumor area further reduces local recurrences. We investigated the dosimetric benefits of a simultaneously integrated boost (SIB compared to a sequential boost to hypofractionate the boost volume, while maintaining normofractionation on the breast. Methods. For 10 patients 4 treatment plans were deployed, 1 with a sequential photon boost, and 3 with different SIB techniques: on a conventional linear accelerator, helical TomoTherapy, and static TomoDirect. Dosimetric comparison was performed. Results. PTV-coverage was good in all techniques. Conformity was better with all SIB techniques compared to sequential boost (P = 0.0001. There was less dose spilling to the ipsilateral breast outside the PTVboost (P = 0.04. The dose to the organs at risk (OAR was not influenced by SIB compared to sequential boost. Helical TomoTherapy showed a higher mean dose to the contralateral breast, but less than 5 Gy for each patient. Conclusions. SIB showed less dose spilling within the breast and equal dose to OAR compared to sequential boost. Both helical TomoTherapy and the conventional technique delivered acceptable dosimetry. SIB seems a safe alternative and can be implemented in clinical routine.

Boosted dark matter signals uplifted with self-interaction

Energy Technology Data Exchange (ETDEWEB)

Kong, Kyoungchul, E-mail: kckong@ku.edu [Department of Physics and Astronomy, University of Kansas, Lawrence, KS 66045 (United States); Mohlabeng, Gopolang, E-mail: mohlabeng319@gmail.com [Department of Physics and Astronomy, University of Kansas, Lawrence, KS 66045 (United States); Park, Jong-Chul, E-mail: log1079@gmail.com [Department of Physics and Astronomy, University of Kansas, Lawrence, KS 66045 (United States); Department of Physics, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

2015-04-09

We explore detection prospects of a non-standard dark sector in the context of boosted dark matter. We focus on a scenario with two dark matter particles of a large mass difference, where the heavier candidate is secluded and interacts with the standard model particles only at loops, escaping existing direct and indirect detection bounds. Yet its pair annihilation in the galactic center or in the Sun may produce boosted stable particles, which could be detected as visible Cherenkov light in large volume neutrino detectors. In such models with multiple candidates, self-interaction of dark matter particles is naturally utilized in the assisted freeze-out mechanism and is corroborated by various cosmological studies such as N-body simulations of structure formation, observations of dwarf galaxies, and the small scale problem. We show that self-interaction of the secluded (heavier) dark matter greatly enhances the capture rate in the Sun and results in promising signals at current and future experiments. We perform a detailed analysis of the boosted dark matter events for Super-Kamiokande, Hyper-Kamiokande and PINGU, including notable effects such as evaporation due to self-interaction and energy loss in the Sun.

Influence of the timing of a concomitant boost during fractionated irradiation of rat rhabdomyosarcoma R1H

International Nuclear Information System (INIS)

Dubben, H.H.; Beck-Bornholdt, H.P.

1993-01-01

Rhabdomyosarcomas R1H of the rat (WAG/Rij) were treated using fractionation schedules including a boost. The total dose was 60 Gy. Overall treatment time was 6 weeks. Four different boost schedules were applied: A single dose boost (12.15 Gy) at the last day of treatment, a single dose boost (12.15 Gy) at the first day of treatment, a schedule including the boost in 7 fractions during the first week, and a schedule including the boost in 10 fractions during the first week of treatment. A standard schedule with 30 fractions of 2 Gy without a boost was used for comparison. Initially accelerated schedules, i.e. those with a boost at start of treatment, revealed higher effect on tumour parenchyma as monitored by local control rate and net growth delay. This could be due to a decrease of radio-sensitivity, that is, an increase of the hypoxic fraction of clonogenic tumour cells during fractionated irradiation. (orig.)

Quality assurance in breast cancer brachytherapy: geographic miss in the interstitial boost treatment of the tumor bed.

Science.gov (United States)

Sedlmayer, F; Rahim, H B; Kogelnik, H D; Menzel, C; Merz, F; Deutschmann, H; Kranzinger, M

1996-03-15

To assess the role of geographic misses in the interstitial boost treatment of breast cancer patients and to evaluate methods of optimizing breast implants in design, performance, and dosimetry. During lumpectomy, the tumor excision sites of 89 patients were marked by five hemoclips. Postoperative radiographs demonstrated the clips' positions with respect to the extension of the surgical cavity, which was demarcated by air and hematoseroma. Twenty-seven selected patients received interstitial boosts to the tumor bed. The implant was first designed according to the clinical assumptions of the tumor bed's topography and then compared with the radiological findings. Prior to brachytherapy, the planning of the implant's dimension and the needle guidance was performed under simulator control. Dose distributions were first calculated following the Paris System and then electively optimized for the target volume by changing source positions and dwell times. Compared to clinical estimations, the radiological determination of the tumor bed's location revealed an overall potential of topographic errors of 51.8% (14 out of 27 patients), rising up to 78.5% in patients with large adipose breasts (11 out of 13 patients). This observation was due to a high mobility of the tissue, leading to varying tumor site projections at the time of mammography, surgery, and brachytherapy. In all patients, the presimulation of the implant resulted in an adequate coverage of the target volume. In 17 of the 27 treated patients, dose distributions were modified to achieve a higher dose delivery in zones where a higher residual tumor load was expected (boost-in-boost). Breast implants have a high potential of geographic misses that can be avoided by intraoperative clip demarcation. The delineation of the tumor bed allows for dose reports actually referring to the target volume and not to the implant system to be obtained. In addition, modern afterloading techniques offer possibilities of

Quality assurance in breast cancer brachytherapy: geographic miss in the interstitial boost treatment of the tumor bed

International Nuclear Information System (INIS)

Sedlmayer, Felix; Rahim, Hassan B. K.; Kogelnik, H. Dieter; Menzel, Christian; Merz, Florian; Deutschmann, Heinz; Kranzinger, Manfred

1996-01-01

Purpose: To assess the role of geographic misses in the interstitial boost treatment of breast cancer patients and to evaluate methods of optimizing breast implants in design, performance, and dosimetry. Methods and Materials: During lumpectomy, the tumor excision sites of 89 patients were marked by five hemoclips. Postoperative radiographs demonstrated the clips' positions with respect to the extension of the surgical cavity, which was demarcated by air and hematoseroma. Twenty-seven selected patients received interstitial boosts to the tumor bed. The implant was first designed according to the clinical assumptions of the tumor bed's topography and then compared with the radiological findings. Prior to brachytherapy, the planning of the implant's dimension and the needle guidance was performed under simulator control. Dose distributions were first calculated following the Paris System and then electively optimized for the target volume by changing source positions and dwell times. Results: Compared to clinical estimations, the radiological determination of the tumor bed's location revealed an overall potential of topographic errors of 51.8% (14 out of 27 patients), rising up to 78.5% in patients with large adipose breasts (11 out of 13 patients). This observation was due to a high mobility of the tissue, leading to varying tumor site projections at the time of mammography, surgery, and brachytherapy. In all patients, the presimulation of the implant resulted in an adequate coverage of the target volume. In 17 of the 27 treated patients, dose distributions were modified to achieve a higher dose delivery in zones where a higher residual tumor load was expected (boost-in-boost). Conclusion: Breast implants have a high potential of geographic misses that can be avoided by intraoperative clip demarcation. The delineation of the tumor bed allows for dose reports actually referring to the target volume and not to the implant system to be obtained. In addition, modern

Quadratic Boost A-Source Impedance Network

DEFF Research Database (Denmark)

Siwakoti, Yam Prasad; Blaabjerg, Frede; Chub, Andrii

2016-01-01

A novel quadratic boost A-source impedance network is proposed to realize converters that demand very high voltage gain. To satisfy the requirement, the network uses an autotransformer where the obtained gain is quadratically dependent on the duty ratio and is unmatched by any existing impedance...

Emerging Cancer Vaccines: The Promise of Genetic Vectors

International Nuclear Information System (INIS)

Aurisicchio, Luigi; Ciliberto, Gennaro

2011-01-01

Therapeutic vaccination against cancer is an important approach which, when combined with other therapies, can improve long-term control of cancer. In fact, the induction of adaptive immune responses against Tumor Associated Antigens (TAAs) as well as innate immunity are important factors for tumor stabilization/eradication. A variety of immunization technologies have been explored in last decades and are currently under active evaluation, such as cell-based, protein, peptide and heat-shock protein-based cancer vaccines. Genetic vaccines are emerging as promising methodologies to elicit immune responses against a wide variety of antigens, including TAAs. Amongst these, Adenovirus (Ad)-based vectors show excellent immunogenicity profile and have achieved immunological proof of concept in humans. In vivo electroporation of plasmid DNA (DNA-EP) is also a desirable vaccine technology for cancer vaccines, as it is repeatable several times, a parameter required for the long-term maintenance of anti-tumor immunity. Recent findings show that combinations of different modalities of immunization (heterologous prime/boost) are able to induce superior immune reactions as compared to single-modality vaccines. In this review, we will discuss the challenges and requirements of emerging cancer vaccines, particularly focusing on the genetic cancer vaccines currently under active development and the promise shown by Ad and DNA-EP heterologous prime-boost

Substructure of Highly Boosted Massive Jets

Energy Technology Data Exchange (ETDEWEB)

Alon, Raz [Weizmann Inst. of Science, Rehovot (Israel)

2012-10-01

Modern particle accelerators enable researchers to study new high energy frontiers which have never been explored before. This realm opens possibilities to further examine known fields such as Quantum Chromodynamics. In addition, it allows searching for new physics and setting new limits on the existence of such. This study examined the substructure of highly boosted massive jets measured by the CDF II detector. Events from 1.96 TeV proton-antiproton collisions at the Fermilab Tevatron Collider were collected out of a total integrated luminosity of 5.95 fb$^{-1}$. They were selected to have at least one jet with transverse momentum above 400 GeV/c. The jet mass, angularity, and planar flow were measured and compared with predictions of perturbative Quantum Chromodynamics, and were found to be consistent with the theory. A search for boosted top quarks was conducted and resulted in an upper limit on the production cross section of such top quarks.

Diesel Combustion and Emission Using High Boost and High Injection Pressure in a Single Cylinder Engine

Science.gov (United States)

Aoyagi, Yuzo; Kunishima, Eiji; Asaumi, Yasuo; Aihara, Yoshiaki; Odaka, Matsuo; Goto, Yuichi

Heavy-duty diesel engines have adopted numerous technologies for clean emissions and low fuel consumption. Some are direct fuel injection combined with high injection pressure and adequate in-cylinder air motion, turbo-intercooler systems, and strong steel pistons. Using these technologies, diesel engines have achieved an extremely low CO2 emission as a prime mover. However, heavy-duty diesel engines with even lower NOx and PM emission levels are anticipated. This study achieved high-boost and lean diesel combustion using a single cylinder engine that provides good engine performance and clean exhaust emission. The experiment was done under conditions of intake air quantity up to five times that of a naturally aspirated (NA) engine and 200MPa injection pressure. The adopted pressure booster is an external supercharger that can control intake air temperature. In this engine, the maximum cylinder pressure was increased and new technologies were adopted, including a monotherm piston for endurance of Pmax =30MPa. Moreover, every engine part is newly designed. As the boost pressure increases, the rate of heat release resembles the injection rate and becomes sharper. The combustion and brake thermal efficiency are improved. This high boost and lean diesel combustion creates little smoke; ISCO and ISTHC without the ISNOx increase. It also yields good thermal efficiency.

Effect of pole zero location on system dynamics of boost converter for micro grid

Science.gov (United States)

Lavanya, A.; Vijayakumar, K.; Navamani, J. D.; Jayaseelan, N.

2018-04-01

Green clean energy like photo voltaic, wind energy, fuel cell can be brought together by microgrid.For low voltage sources like photovoltaic cell boost converter is very much essential. This paper explores the dynamic analysis of boost converter in a continuous conduction mode (CCM). The transient performance and stability analysis is carried out in this paper using time domain analysis and frequency domain analysis techniques. Boost converter is simulated using both PSIM and MATLAB software. Furthermore, state space model obtained and the transfer function is derived. The converter behaviour when a step input is applied is analyzed and stability of the converter is analyzed from bode plot frequency for open loop. Effect of the locations of poles and zeros in the transfer function of boost converter and how the performance parameters are affected is discussed in this paper. Closed loop performance with PI controller is also analyzed for boost converter.

CT planning of boost irradiation in radiotherapy of breast cancer after conservative surgery

International Nuclear Information System (INIS)

Messer, Peter M.; Kirikuta, Ion C.; Bratengeier, Klaus; Flentje, Michael

1997-01-01

Background and purpose: A study was performed to compare the accuracy of clinical treatment set-up and CT planning of boost irradiation in radiotherapy of breast cancer. Material and methods: Between September 1993 and October 1994, 45 women who underwent breast conserving surgery and irradiation containing a boost to the tumour bed were investigated. Prospective evaluation of CT planning of the boost was carried out. The target volume/boost field, electron energy and treatment set-up had been defined on the basis of clinical examination, initial and postsurgical mammograms by one radiotherapist. Next, a planning CT was performed in treatment position and a CT-based treatment plan was calculated according to a target volume defined by another radiotherapist. The clinical treatment set-up was imported into our computer planning system and the resulting isodose plots were compared with those from CT planning and reviewed critically. Results: The clinically defined treatment set-up had to be modified in 80% of the patients. Most discrepancies observed were related to the size of the boost field itself and the chosen electron energy. Minor changes had to be made with respect to angle of table and gantry. Conclusions: Critical review of the isodose plots from both methods showed clear advantages for CT planning. Guidelines for target definition in CT planning of boost irradiation and subgroups of patients benefiting from this technique are described

Maximum power point tracking techniques for wind energy systems using three levels boost converter

Science.gov (United States)

Tran, Cuong Hung; Nollet, Frédéric; Essounbouli, Najib; Hamzaoui, Abdelaziz

2018-05-01

This paper presents modeling and simulation of three level Boost DC-DC converter in Wind Energy Conversion System (WECS). Three-level Boost converter has significant advantage compared to conventional Boost. A maximum power point tracking (MPPT) method for a variable speed wind turbine using permanent magnet synchronous generator (PMSG) is also presented. Simulation of three-level Boost converter topology with Perturb and Observe algorithm and Fuzzy Logic Control is implemented in MATLAB/SIMULINK. Results of this simulation show that the system with MPPT using fuzzy logic controller has better performance to the Perturb and Observe algorithm: fast response under changing conditions and small oscillation.

Pathway-Based Kernel Boosting for the Analysis of Genome-Wide Association Studies

Science.gov (United States)

Manitz, Juliane; Burger, Patricia; Amos, Christopher I.; Chang-Claude, Jenny; Wichmann, Heinz-Erich; Kneib, Thomas; Bickeböller, Heike

2017-01-01

The analysis of genome-wide association studies (GWAS) benefits from the investigation of biologically meaningful gene sets, such as gene-interaction networks (pathways). We propose an extension to a successful kernel-based pathway analysis approach by integrating kernel functions into a powerful algorithmic framework for variable selection, to enable investigation of multiple pathways simultaneously. We employ genetic similarity kernels from the logistic kernel machine test (LKMT) as base-learners in a boosting algorithm. A model to explain case-control status is created iteratively by selecting pathways that improve its prediction ability. We evaluated our method in simulation studies adopting 50 pathways for different sample sizes and genetic effect strengths. Additionally, we included an exemplary application of kernel boosting to a rheumatoid arthritis and a lung cancer dataset. Simulations indicate that kernel boosting outperforms the LKMT in certain genetic scenarios. Applications to GWAS data on rheumatoid arthritis and lung cancer resulted in sparse models which were based on pathways interpretable in a clinical sense. Kernel boosting is highly flexible in terms of considered variables and overcomes the problem of multiple testing. Additionally, it enables the prediction of clinical outcomes. Thus, kernel boosting constitutes a new, powerful tool in the analysis of GWAS data and towards the understanding of biological processes involved in disease susceptibility. PMID:28785300

Pathway-Based Kernel Boosting for the Analysis of Genome-Wide Association Studies.

Science.gov (United States)

Friedrichs, Stefanie; Manitz, Juliane; Burger, Patricia; Amos, Christopher I; Risch, Angela; Chang-Claude, Jenny; Wichmann, Heinz-Erich; Kneib, Thomas; Bickeböller, Heike; Hofner, Benjamin

2017-01-01

The analysis of genome-wide association studies (GWAS) benefits from the investigation of biologically meaningful gene sets, such as gene-interaction networks (pathways). We propose an extension to a successful kernel-based pathway analysis approach by integrating kernel functions into a powerful algorithmic framework for variable selection, to enable investigation of multiple pathways simultaneously. We employ genetic similarity kernels from the logistic kernel machine test (LKMT) as base-learners in a boosting algorithm. A model to explain case-control status is created iteratively by selecting pathways that improve its prediction ability. We evaluated our method in simulation studies adopting 50 pathways for different sample sizes and genetic effect strengths. Additionally, we included an exemplary application of kernel boosting to a rheumatoid arthritis and a lung cancer dataset. Simulations indicate that kernel boosting outperforms the LKMT in certain genetic scenarios. Applications to GWAS data on rheumatoid arthritis and lung cancer resulted in sparse models which were based on pathways interpretable in a clinical sense. Kernel boosting is highly flexible in terms of considered variables and overcomes the problem of multiple testing. Additionally, it enables the prediction of clinical outcomes. Thus, kernel boosting constitutes a new, powerful tool in the analysis of GWAS data and towards the understanding of biological processes involved in disease susceptibility.

Avoiding Anemia: Boost Your Red Blood Cells

Science.gov (United States)

... Issues Subscribe January 2014 Print this issue Avoiding Anemia Boost Your Red Blood Cells En español Send ... Disease When Blood Cells Bend Wise Choices Preventing Anemia To prevent or treat iron-deficiency anemia: Eat ...

A Survey on Voltage Boosting Techniques for Step-Up DC-DC Converters

DEFF Research Database (Denmark)

Forouzesh, Mojtaba; Siwakoti, Yam Prasad; Gorji, Saman Asghari

2016-01-01

boosting techniques and topologies are large, which at times may be confusing and difficult to follow/adapt for different applications. Considering these aspects and in order to make a clear sketch of the general law and framework of various voltage boosting techniques, this paper comprehensively reviews...

Semi-supervised learning via regularized boosting working on multiple semi-supervised assumptions.

Science.gov (United States)

Chen, Ke; Wang, Shihai

2011-01-01

Semi-supervised learning concerns the problem of learning in the presence of labeled and unlabeled data. Several boosting algorithms have been extended to semi-supervised learning with various strategies. To our knowledge, however, none of them takes all three semi-supervised assumptions, i.e., smoothness, cluster, and manifold assumptions, together into account during boosting learning. In this paper, we propose a novel cost functional consisting of the margin cost on labeled data and the regularization penalty on unlabeled data based on three fundamental semi-supervised assumptions. Thus, minimizing our proposed cost functional with a greedy yet stagewise functional optimization procedure leads to a generic boosting framework for semi-supervised learning. Extensive experiments demonstrate that our algorithm yields favorite results for benchmark and real-world classification tasks in comparison to state-of-the-art semi-supervised learning algorithms, including newly developed boosting algorithms. Finally, we discuss relevant issues and relate our algorithm to the previous work.

Chagas Parasite Detection in Blood Images Using AdaBoost

Directory of Open Access Journals (Sweden)

Víctor Uc-Cetina

2015-01-01

Full Text Available The Chagas disease is a potentially life-threatening illness caused by the protozoan parasite, Trypanosoma cruzi. Visual detection of such parasite through microscopic inspection is a tedious and time-consuming task. In this paper, we provide an AdaBoost learning solution to the task of Chagas parasite detection in blood images. We give details of the algorithm and our experimental setup. With this method, we get 100% and 93.25% of sensitivity and specificity, respectively. A ROC comparison with the method most commonly used for the detection of malaria parasites based on support vector machines (SVM is also provided. Our experimental work shows mainly two things: (1 Chagas parasites can be detected automatically using machine learning methods with high accuracy and (2 AdaBoost + SVM provides better overall detection performance than AdaBoost or SVMs alone. Such results are the best ones known so far for the problem of automatic detection of Chagas parasites through the use of machine learning, computer vision, and image processing methods.

Boosted decision trees as an alternative to artificial neural networks for particle identification

International Nuclear Information System (INIS)

Roe, Byron P.; Yang Haijun; Zhu Ji; Liu Yong; Stancu, Ion; McGregor, Gordon

2005-01-01

The efficacy of particle identification is compared using artificial neutral networks and boosted decision trees. The comparison is performed in the context of the MiniBooNE, an experiment at Fermilab searching for neutrino oscillations. Based on studies of Monte Carlo samples of simulated data, particle identification with boosting algorithms has better performance than that with artificial neural networks for the MiniBooNE experiment. Although the tests in this paper were for one experiment, it is expected that boosting algorithms will find wide application in physics

Boosting bonsai trees for handwritten/printed text discrimination

Science.gov (United States)

Ricquebourg, Yann; Raymond, Christian; Poirriez, Baptiste; Lemaitre, Aurélie; Coüasnon, Bertrand

2013-12-01

Boosting over decision-stumps proved its efficiency in Natural Language Processing essentially with symbolic features, and its good properties (fast, few and not critical parameters, not sensitive to over-fitting) could be of great interest in the numeric world of pixel images. In this article we investigated the use of boosting over small decision trees, in image classification processing, for the discrimination of handwritten/printed text. Then, we conducted experiments to compare it to usual SVM-based classification revealing convincing results with very close performance, but with faster predictions and behaving far less as a black-box. Those promising results tend to make use of this classifier in more complex recognition tasks like multiclass problems.

Y-source impedance-network-based isolated boost DC/DC converter

DEFF Research Database (Denmark)

Siwakoti, Yam P.; Town, Graham; Loh, Poh Chiang

2014-01-01

A dc-dc converter with very high voltage gain is proposed in this paper for any medium-power application requiring a high voltage boost with galvanic isolation. The proposed converter topology can be realized using only two switches. With this topology a very high voltage boost can be achieved even...... with a relatively low duty cycle of the switches, and the gain obtainable is presently not matched by any existing impedance network based converter operated at the same duty ratio. The proposed converter has a Y-source impedance network to boost the voltage at the intermediate dc-link side and a push......-pull transformer for square-wave AC inversion and isolation. The voltage-doubler rectifier provides a constant dc voltage at the output stage. A theoretical analysis of the converter is presented, supported by simulation and experimental results. A 250 W down-scaled prototype was implemented in the laboratory...

Performance of Boosted W Boson Identification with the ATLAS Detector

CERN Document Server

The ATLAS collaboration

2014-01-01

This note presents the performance of a variety of techniques used to identify highly- boosted hadronically-decaying $W$ bosons. The studies presented here are divided into two parts: the first is based on Monte Carlo simulation, and the second compares the simulations to 20.3$\\pm$0.6 fb$^{-1}$ of proton-–proton collisions data collected by the ATLAS detector in 2012 at $\\sqrt{s} = 8$ TeV. Various tagging approaches and different grooming algorithms are compared in simulation, using a signal of large-$R$ jets containing a highly boosted $W$ boson and a background of large-$R$ jets originating from high-momentum light quarks or gluons. These techniques could also be utilised to identify hadronic decays of boosted $Z$ and Higgs bosons. A sample enriched in $t\\bar{t}\\to (W^+b)(W^-\\bar{b}) \\to (q\\bar{q}b)(\\mu \\bar{\

Demonstration of brachytherapy boost dose-response relationships in glioblastoma multiforme

International Nuclear Information System (INIS)

Sneed, Penny K.; Lamborn, Kathleen R.; Larson, David A.; Prados, Michael D.; Malec, Mary K.; McDermott, Michael W.; Weaver, Keith A.; Phillips, Theodore L.; Wara, William M.; Gutin, Philip H.

1996-01-01

Purpose: To evaluate brachytherapy dose-response relationships in adults with glioblastoma undergoing temporary 125 I implant boost after external beam radiotherapy. Methods and Materials: Since June 1987, orthogonal radiographs using a fiducial marker box have been used to verify brain implant source positions and generate dose-volume histograms at the University of California, San Francisco. For adults who underwent brachytherapy boost for glioblastoma from June 1987 through December 1992, tumor volumes were reoutlined to ensure consistency and dose-volume histograms were recalculated. Univariate and multivariate analyses of various patient and treatment parameters were performed evaluating for influence of dose on freedom from local failure (FFLF) and actuarial survival. Results: Of 102 implant boosts, 5 were excluded because computer plans were unavailable. For the remaining 97 patients, analyses with adjustment for known prognostic factors (age, KPS, extent of initial surgical resection) and prognostic factors identified on univariate testing (adjuvant chemotherapy) showed that higher minimum brachytherapy tumor dose was strongly associated with improved FFLF (p = 0.001). A quadratic relationship was found between total biological effective dose and survival, with a trend toward optimal survival probability at 47 Gy minimum brachytherapy tumor dose (corresponding to about 65 Gy to 95% of the tumor volume); survival decreased with lower or higher doses. Two patients expired and one requires hospice care because of brain necrosis after brachytherapy doses > 63 Gy to 95% of the tumor volume with 60 Gy to > 18 cm 3 of normal brain. Conclusion: Although higher minimum brachytherapy tumor dose was strongly associated with better local control, a brachytherapy boost dose > 50-60 Gy may result in life-threatening necrosis. We recommend careful conformation of the prescription isodose line to the contrast enhancing tumor volume, delivery of a minimum brachytherapy

Boosted H­->bb Tagger In Run II

CERN Document Server

Sahinsoy, Merve; The ATLAS collaboration

2016-01-01

Several searches for Higgs bosons decaying to b­quark pairs benefit from the increased Run II centre­of­mass energy by exploiting the large transvers­momentum (boosted) Higgs boson regime, where the two b­jets are merged into one large­radius jet. ATLAS uses a boosted H­>bb tagger algorithm to separate the Higgs signal from the background processes (QCD, W and Z bosons, top quarks). The tagger takes as input a large­R=1.0 jet calibrating the pseudorapidity, energy and mass scale. The tagger employs b­tagging, Higgs candidate mass, and substructure information. The performance of several operating points in Higgs boson signal and QCD and ttbar all­hadronic backgrounds are presented. Systematic uncertainties are evaluated so that this tagger can be used in analyses.

RTL2RTL Formal Equivalence: Boosting the Design Confidence

Directory of Open Access Journals (Sweden)

M V Achutha Kiran Kumar

2014-07-01

Full Text Available Increasing design complexity driven by feature and performance requirements and the Time to Market (TTM constraints force a faster design and validation closure. This in turn enforces novel ways of identifying and debugging behavioral inconsistencies early in the design cycle. Addition of incremental features and timing fixes may alter the legacy design behavior and would inadvertently result in undesirable bugs. The most common method of verifying the correctness of the changed design is to run a dynamic regression test suite before and after the intended changes and compare the results, a method which is not exhaustive. Modern Formal Verification (FV techniques involving new methods of proving Sequential Hardware Equivalence enabled a new set of solutions for the given problem, with complete coverage guarantee. Formal Equivalence can be applied for proving functional integrity after design changes resulting from a wide variety of reasons, ranging from simple pipeline optimizations to complex logic redistributions. We present here our experience of successfully applying the RTL to RTL (RTL2RTL Formal Verification across a wide spectrum of problems on a Graphics design. The RTL2RTL FV enabled checking the design sanity in a very short time, thus enabling faster and safer design churn. The techniques presented in this paper are applicable to any complex hardware design.

Application of Boosting Regression Trees to Preliminary Cost Estimation in Building Construction Projects

Directory of Open Access Journals (Sweden)

Yoonseok Shin

2015-01-01

Full Text Available Among the recent data mining techniques available, the boosting approach has attracted a great deal of attention because of its effective learning algorithm and strong boundaries in terms of its generalization performance. However, the boosting approach has yet to be used in regression problems within the construction domain, including cost estimations, but has been actively utilized in other domains. Therefore, a boosting regression tree (BRT is applied to cost estimations at the early stage of a construction project to examine the applicability of the boosting approach to a regression problem within the construction domain. To evaluate the performance of the BRT model, its performance was compared with that of a neural network (NN model, which has been proven to have a high performance in cost estimation domains. The BRT model has shown results similar to those of NN model using 234 actual cost datasets of a building construction project. In addition, the BRT model can provide additional information such as the importance plot and structure model, which can support estimators in comprehending the decision making process. Consequently, the boosting approach has potential applicability in preliminary cost estimations in a building construction project.

Traditional grains boost nutrition in rural India

International Development Research Centre (IDRC) Digital Library (Canada)

India, particularly among vulnerable women and children. The research ... This approach will improve the quality of life for farmers, and is part of a long-term solution to rural poverty in India. ... Traditional grains boost nutrition in rural India.

An imaging evaluation of the simultaneously integrated boost breast radiotherapy technique

Energy Technology Data Exchange (ETDEWEB)

Turley, Jessica; Claridge Mackonis, Elizabeth [Department of Radiation Oncology, Royal Prince Alfred Hospital, Camperdown, New South Wales (Australia)

2015-09-15

To evaluate in-field megavoltage (MV) imaging of simultaneously integrated boost (SIB) breast fields to determine its feasibility in treatment verification for the SIB breast radiotherapy technique, and to assess whether the current-imaging protocol and treatment margins are sufficient. For nine patients undergoing SIB breast radiotherapy, in-field MV images of the SIB fields were acquired on days that regular treatment verification imaging was performed. The in-field images were matched offline according to the scar wire on digitally reconstructed radiographs. The offline image correction results were then applied to a margin recipe formula to calculate safe margins that account for random and systematic uncertainties in the position of the boost volume when an offline correction protocol has been applied. After offline assessment of the acquired images, 96% were within the tolerance set in the current department-imaging protocol. Retrospectively performing the maximum position deviations on the Eclipse™ treatment planning system demonstrated that the clinical target volume (CTV) boost received a minimum dose difference of 0.4% and a maximum dose difference of 1.4% less than planned. Furthermore, applying our results to the Van Herk margin formula to ensure that 90% of patients receive 95% of the prescribed dose, the calculated CTV margins were comparable to the current departmental procedure used. Based on the in-field boost images acquired and the feasible application of these results to the margin formula the current CTV-planning target volume margins used are appropriate for the accurate treatment of the SIB boost volume without additional imaging.

An imaging evaluation of the simultaneously integrated boost breast radiotherapy technique

International Nuclear Information System (INIS)

Turley, Jessica; Claridge Mackonis, Elizabeth

2015-01-01

To evaluate in-field megavoltage (MV) imaging of simultaneously integrated boost (SIB) breast fields to determine its feasibility in treatment verification for the SIB breast radiotherapy technique, and to assess whether the current-imaging protocol and treatment margins are sufficient. For nine patients undergoing SIB breast radiotherapy, in-field MV images of the SIB fields were acquired on days that regular treatment verification imaging was performed. The in-field images were matched offline according to the scar wire on digitally reconstructed radiographs. The offline image correction results were then applied to a margin recipe formula to calculate safe margins that account for random and systematic uncertainties in the position of the boost volume when an offline correction protocol has been applied. After offline assessment of the acquired images, 96% were within the tolerance set in the current department-imaging protocol. Retrospectively performing the maximum position deviations on the Eclipse™ treatment planning system demonstrated that the clinical target volume (CTV) boost received a minimum dose difference of 0.4% and a maximum dose difference of 1.4% less than planned. Furthermore, applying our results to the Van Herk margin formula to ensure that 90% of patients receive 95% of the prescribed dose, the calculated CTV margins were comparable to the current departmental procedure used. Based on the in-field boost images acquired and the feasible application of these results to the margin formula the current CTV-planning target volume margins used are appropriate for the accurate treatment of the SIB boost volume without additional imaging

Analysis and design of a standardized control module for switching regulators

Science.gov (United States)

Lee, F. C.; Mahmoud, M. F.; Yu, Y.; Kolecki, J. C.

1982-07-01

Three basic switching regulators: buck, boost, and buck/boost, employing a multiloop standardized control module (SCM) were characterized by a common small signal block diagram. Employing the unified model, regulator performances such as stability, audiosusceptibility, output impedance, and step load transient are analyzed and key performance indexes are expressed in simple analytical forms. More importantly, the performance characteristics of all three regulators are shown to enjoy common properties due to the unique SCM control scheme which nullifies the positive zero and provides adaptive compensation to the moving poles of the boost and buck/boost converters. This allows a simple unified design procedure to be devised for selecting the key SCM control parameters for an arbitrarily given power stage configuration and parameter values, such that all regulator performance specifications can be met and optimized concurrently in a single design attempt.

Radiotherapy Boost Following Conservative Surgery for Locally Advanced Breast Cancer

International Nuclear Information System (INIS)

Cendales, Ricardo; Ospino, Rosalba; Torres, Felipe; Cotes, Martha

2009-01-01

Nearly half of breast cancer patients in developing countries present with a locally advanced cancer. Treatment is centered on a multimodal approach based on chemotherapy, surgery and radiotherapy. The growing use of neoadjuvant chemotherapy has led to a more conservative surgical approach; nonetheless, it is not yet considered as a standard. There are no clear recommendations on the use of a radiotherapy boost in such situation. A Medline search was developed. Most articles are retrospective series. Survival free of locoregional relapse in patients treated with neoadjuvant chemotherapy, breast conserving surgery and radiotherapy is good. All articles described a boost administered to nearly all patients without regard to their prognostic factors, given that a locally advanced tumor is already considered as a poor prognostic factor. Even tough the poor level of evidence, a recommendation can be made: radiotherapy boost should be administered to all patients with locally advanced breast cancer treated with neoadjuvant chemotherapy and breast conserving surgery.

Emergency planning simplification: Why ALWR designs shall support this goal

International Nuclear Information System (INIS)

Tripputi, I.

2004-01-01

Emergency Plan simplification, could be achieved only if it can proved, in a context of balanced national health protection policies, that there is a reduced or no technical need for some elements of it and that public protection is assured in all considered situations regardless of protective actions outside the plant. These objectives may be technically supported if one or more of the following conditions are complied with: 1. Accidents potentially releasing large amounts of fission products can be ruled out by characteristics of the designs 2. Plant engineered features (and the containment system in particular) are able to drastically mitigate the radioactive releases under all conceivable scenarios. 3. A realistic approach to the consequence evaluation can reduce the expected consequences to effects below any concern. Unfortunately no one single approach is either technically feasible or justified in a perspective of defense in depth and only a mix of them may provide the necessary conditions. It appears that most or all proposed ALWR designs address the technical issues, whose solutions are the bases to eliminate the need for a number of protective actions (evacuation, relocation, sheltering, iodine tablets administration, etc.) even in the case of a severe accident. Some designs are mainly oriented to prevent the need for short term protective actions; they credit simplified Emergency Plans or the capabilities of existing civil protection organizations for public relocation in the long term, if needed. Others take also into account the overall releases to exclude or minimize public relocation and land contamination. Design targets for population individual doses and for land contamination proposed in Italy are discussed in the paper. It is also shown that these limits, while challenging, appear to be within the reach of the next generation proposed designs currently studied in Italy. (author)

Wide Temperature Range DC-DC Boost Converters for Command/Control/Drive Electronics, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — We shall develop wide temperature range DC-DC boost converters that can be fabricated using commercial CMOS foundries. The boost converters will increase the low...

Niacin to Boost Your HDL "Good" Cholesterol

Science.gov (United States)

Niacin can boost 'good' cholesterol Niacin is a B vitamin that may raise your HDL ("good") cholesterol. But side effects might outweigh benefits for most ... been used to increase high-density lipoprotein (HDL) cholesterol — the "good" cholesterol that helps remove low-density ...

Emerging Techniques in Stratified Designs and Continuous Gradients for Tissue Engineering of Interfaces

Science.gov (United States)

Dormer, Nathan H.; Berkland, Cory J.; Detamore, Michael S.

2013-01-01

Interfacial tissue engineering is an emerging branch of regenerative medicine, where engineers are faced with developing methods for the repair of one or many functional tissue systems simultaneously. Early and recent solutions for complex tissue formation have utilized stratified designs, where scaffold formulations are segregated into two or more layers, with discrete changes in physical or chemical properties, mimicking a corresponding number of interfacing tissue types. This method has brought forth promising results, along with a myriad of regenerative techniques. The latest designs, however, are employing “continuous gradients” in properties, where there is no discrete segregation between scaffold layers. This review compares the methods and applications of recent stratified approaches to emerging continuously graded methods. PMID:20411333

Closed-loop waveform control of boost inverter

DEFF Research Database (Denmark)

Zhu, Guo Rong; Xiao, Cheng Yuan; Wang, Haoran

2016-01-01

The input current of single-phase inverter typically has an AC ripple component at twice the output frequency, which causes a reduction in both the operating lifetime of its DC source and the efficiency of the system. In this paper, the closed-loop performance of a proposed waveform control method...... to eliminate such a ripple current in boost inverter is investigated. The small-signal stability and the dynamic characteristic of the inverter system for input voltage or wide range load variations under the closed-loop waveform control method are studied. It is validated that with the closedloop waveform...... control, not only was stability achieved, the reference voltage of the boost inverter capacitors can be instantaneously adjusted to match the new load, thereby achieving improved ripple mitigation for a wide load range. Furthermore, with the control and feedback mechanism, there is minimal level of ripple...

Protecting livelihoods, boosting food security in Kenya | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

2015-05-21

May 21, 2015 ... Protecting livelihoods, boosting food security in Kenya ... livestock fodder, with important outcomes for household food security. ... and all counties have since committed funding toward scaling up successful technologies.

Exploiting tRNAs to Boost Virulence

Directory of Open Access Journals (Sweden)

Suki Albers

2016-01-01

Full Text Available Transfer RNAs (tRNAs are powerful small RNA entities that are used to translate nucleotide language of genes into the amino acid language of proteins. Their near-uniform length and tertiary structure as well as their high nucleotide similarity and post-transcriptional modifications have made it difficult to characterize individual species quantitatively. However, due to the central role of the tRNA pool in protein biosynthesis as well as newly emerging roles played by tRNAs, their quantitative assessment yields important information, particularly relevant for virus research. Viruses which depend on the host protein expression machinery have evolved various strategies to optimize tRNA usage—either by adapting to the host codon usage or encoding their own tRNAs. Additionally, several viruses bear tRNA-like elements (TLE in the 5′- and 3′-UTR of their mRNAs. There are different hypotheses concerning the manner in which such structures boost viral protein expression. Furthermore, retroviruses use special tRNAs for packaging and initiating reverse transcription of their genetic material. Since there is a strong specificity of different viruses towards certain tRNAs, different strategies for recruitment are employed. Interestingly, modifications on tRNAs strongly impact their functionality in viruses. Here, we review those intersection points between virus and tRNA research and describe methods for assessing the tRNA pool in terms of concentration, aminoacylation and modification.

Boosted PWM open loop control of hydraulic proportional valves

International Nuclear Information System (INIS)

Amirante, R.; Innone, A.; Catalano, L.A.

2008-01-01

This paper presents an innovative open loop control technique for direct single stage hydraulic proportional valves whose response rate is significantly higher than that obtained by standard open loop control techniques, even comparable to more costly commercial closed loop systems. Different from standard open loop techniques, which provide the coil with a constant current proportional to the target position, the control strategy proposed in this paper employs the peak and hold (P and H) technique, widely used in Diesel engine modern supply systems, to boost the duty cycle value of the pulse width modulation (PWM) signal for a short time, namely during the spool displacement, while maintaining a lower duty cycle for holding the spool in the required opening position. The developed 'boosted PWM' technique only requires a low cost microcontroller, such as a peripheral interface controller (PIC) equipped with a metal oxide semiconductor (MOS) power driver. The PWM parameters are calibrated as a function of the spool displacement so as to maximize the response rate without introducing overshoots: the collected data are stored in the PIC. Different valve opening procedures with step response have been compared to demonstrate the merits of the proposed boosted PWM technique. No overshoots have been registered. Moreover, the proposed method is characterized by a significantly higher response rate with respect to a standard open loop control, which approximately has the same cost. Similar experimental tests show that the proposed boosted PWM technique has a response rate even higher than that provided by the more costly commercial closed loop system mounted on the valve, and it produces no overshoots

Boosted PWM open loop control of hydraulic proportional valves

Energy Technology Data Exchange (ETDEWEB)

Amirante, R.; Catalano, L.A. [Dipartimento di Ingegneria Meccanica e Gestionale, Politecnico di Bari, Via Re David 200, 70125 Bari (Italy); Innone, A. [Universita degli Studi di Foggia, via Napoli, 25 Foggia (Italy)

2008-08-15

This paper presents an innovative open loop control technique for direct single stage hydraulic proportional valves whose response rate is significantly higher than that obtained by standard open loop control techniques, even comparable to more costly commercial closed loop systems. Different from standard open loop techniques, which provide the coil with a constant current proportional to the target position, the control strategy proposed in this paper employs the peak and hold (P and H) technique, widely used in Diesel engine modern supply systems, to boost the duty cycle value of the pulse width modulation (PWM) signal for a short time, namely during the spool displacement, while maintaining a lower duty cycle for holding the spool in the required opening position. The developed 'boosted PWM' technique only requires a low cost microcontroller, such as a peripheral interface controller (PIC) equipped with a metal oxide semiconductor (MOS) power driver. The PWM parameters are calibrated as a function of the spool displacement so as to maximize the response rate without introducing overshoots: the collected data are stored in the PIC. Different valve opening procedures with step response have been compared to demonstrate the merits of the proposed boosted PWM technique. No overshoots have been registered. Moreover, the proposed method is characterized by a significantly higher response rate with respect to a standard open loop control, which approximately has the same cost. Similar experimental tests show that the proposed boosted PWM technique has a response rate even higher than that provided by the more costly commercial closed loop system mounted on the valve, and it produces no overshoots. (author)

Experimental Research in Boost Driver with EDLCs

Science.gov (United States)

Matsumoto, Hirokazu

The supply used in servo systems tends to have a high voltage in order to reduce loss and improve the response of motor drives. We propose a new boost motor driver that comprises EDLCs. The proposed driver has a simple structure, wherein the EDLCs are connected in series to the supply, and comprises a charge circuit to charge the EDLCs. The proposed driver has three advantages over conventional boost drivers. The first advantage is that the driver can easily attain the stable boost voltage. The second advantage is that the driver can reduce input power peaks. In a servo system, the input power peaks become greater than the rated power in order to accelerate the motor rapidly. This implies that the equipments that supply power to servo systems must have sufficient power capacity to satisfy the power peaks. The proposed driver can suppress the increase of the power capacity of supply facilities. The third advantage is that the driver can store almost all of the regenerative energy. Conventional drivers have a braking resistor to suppress the increase in the DC link voltage. This causes a considerable reduction in the efficiency. The proposed driver is more efficient than conventional drivers. In this study, the experimental results confirmed the effectiveness of the proposed driver and showed that the drive performance of the proposed driver is the same as that of a conventional driver. Furthermore, it was confirmed that the results of the simulation of a model of the EDLC module, whose capacitance is dependent on the frequency, correspond well with the experimental results.

Concomitant boost radiotherapy for squamous carcinoma of the tonsillar fossa

International Nuclear Information System (INIS)

Gwozdz, John T.; Morrison, William H.; Garden, Adam S.; Weber, Randal S.; Peters, Lester J.; Ang, K. Kian

1997-01-01

Purpose: To assess the efficacy of a concomitant boost fractionation schedule of radiotherapy for treating patients with squamous carcinoma of the tonsillar fossa. Patients and Methods: Between December 1983 and November 1992, 83 patients with squamous carcinoma of the tonsil were treated with concomitant boost fractionation. The distribution of American Joint Committee on Cancer T stages was TX-4, T1-5, T2-29, T3-41, T4-4; N stages were NX-1, N0-26, N1-13, N2-31, N3-12. Patients were treated with standard large fields to 54 Gy in 6 weeks. The boost treatment consisted of a second daily 1.5 Gy fraction for 10-12 fractions, usually delivered during the final phase of treatment. The tumor dose was 69-72 Gy, given over 6 weeks. Twenty-one patients, who all had N2 or N3 regional disease, underwent neck dissections, either before (13 patients) or 6 weeks after radiotherapy (8 patients); the other patients were treated with radiotherapy alone. Results: The 5-year actuarial disease-specific survival and overall survival rates were 71 and 60%, respectively. Patients with T2 and T3 primary tumors had 5-year actuarial local control rates of 96 and 78%, respectively. Patients with T3 disease who received the final-phase boost had a 5-year actuarial local control rate of 82%. Actuarial 5-year regional disease control rates were N0, 92%; N1, 76%; N2, 89%; and N3, 89%. The 21 patients who had neck dissections all had their disease regionally controlled. Patients presenting with nodal disease or after a node excision who were treated with radiation alone had a 5-year actuarial regional disease control rate of 79%. All but five patients had confluent Grade 4 mucositis during treatment. Severe late complications attributable to radiation included mandibular necrosis, in-field osteosarcoma, and chronic dysphagia for solid foods. Conclusions: High rates of local and regional disease control were achieved with the concomitant boost fractionation schedule, with few cases of severe late

Designing smartphone mental health applications for emergency service workers.

Science.gov (United States)

Deady, M; Peters, D; Lang, H; Calvo, R; Glozier, N; Christensen, H; Harvey, S B

2017-08-01

Emergency service workers are often exposed to trauma and have increased risk of a range of mental health (MH) conditions. Smartphone applications have the potential to provide this group with effective psychological interventions; however, little is known about the acceptability and preferences regarding such initiatives. To describe the preferences and opinions of emergency service workers regarding the use of smartphone MH applications and to examine the impact of age on these preferences. Participants were recruited from four metropolitan Fire and Rescue NSW stations and responded to questionnaire items covering three key domains: current smartphone use, potential future use and preferences for design and content as well as therapeutic techniques. Overall, approximately half the sample (n = 106) claimed they would be interested in trying a tailored emergency-worker MH smartphone application. There were few differences between age groups on preferences. The majority of respondents claimed they would use an app for mental well-being daily and preferred terms such as 'well-being' and 'mental fitness' for referring to MH. Confidentiality, along with a focus on stress, sleep, exercise and resiliency were all considered key features. Behavioural therapeutic techniques were regarded most favourably, compared with other therapies. Emergency workers were interested in utilizing smartphone applications focused on MH, but expressed clear preferences regarding language used in promotion, features required and therapeutic techniques preferred. © The Author 2017. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com

GeoBoost: accelerating research involving the geospatial metadata of virus GenBank records.

Science.gov (United States)

Tahsin, Tasnia; Weissenbacher, Davy; O'Connor, Karen; Magge, Arjun; Scotch, Matthew; Gonzalez-Hernandez, Graciela

2018-05-01

GeoBoost is a command-line software package developed to address sparse or incomplete metadata in GenBank sequence records that relate to the location of the infected host (LOIH) of viruses. Given a set of GenBank accession numbers corresponding to virus GenBank records, GeoBoost extracts, integrates and normalizes geographic information reflecting the LOIH of the viruses using integrated information from GenBank metadata and related full-text publications. In addition, to facilitate probabilistic geospatial modeling, GeoBoost assigns probability scores for each possible LOIH. Binaries and resources required for running GeoBoost are packed into a single zipped file and freely available for download at https://tinyurl.com/geoboost. A video tutorial is included to help users quickly and easily install and run the software. The software is implemented in Java 1.8, and supported on MS Windows and Linux platforms. gragon@upenn.edu. Supplementary data are available at Bioinformatics online.

Adaptive Replanning to Account for Lumpectomy Cavity Change in Sequential Boost After Whole-Breast Irradiation

Energy Technology Data Exchange (ETDEWEB)

Chen, Xiaojian [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States); Qiao, Qiao [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States); Department of Radiotherapy, First Hospital of China Medical University, Shenyang (China); DeVries, Anthony [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States); Li, Wenhui [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States); Department of Radiotherapy, Yunnan Tumor Hospital, Kunming (China); Currey, Adam; Kelly, Tracy; Bergom, Carmen; Wilson, J. Frank [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States); Li, X. Allen, E-mail: ali@mcw.edu [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin (United States)

2014-12-01

Purpose: To evaluate the efficiency of standard image-guided radiation therapy (IGRT) to account for lumpectomy cavity (LC) variation during whole-breast irradiation (WBI) and propose an adaptive strategy to improve dosimetry if IGRT fails to address the interfraction LC variations. Methods and Materials: Daily diagnostic-quality CT data acquired during IGRT in the boost stage using an in-room CT for 19 breast cancer patients treated with sequential boost after WBI in the prone position were retrospectively analyzed. Contours of the LC, treated breast, ipsilateral lung, and heart were generated by populating contours from planning CTs to boost fraction CTs using an auto-segmentation tool with manual editing. Three plans were generated on each fraction CT: (1) a repositioning plan by applying the original boost plan with the shift determined by IGRT; (2) an adaptive plan by modifying the original plan according to a fraction CT; and (3) a reoptimization plan by a full-scale optimization. Results: Significant variations were observed in LC. The change in LC volume at the first boost fraction ranged from a 70% decrease to a 50% increase of that on the planning CT. The adaptive and reoptimization plans were comparable. Compared with the repositioning plans, the adaptive plans led to an improvement in target coverage for an increased LC case (1 of 19, 7.5% increase in planning target volume evaluation volume V{sub 95%}), and breast tissue sparing for an LC decrease larger than 35% (3 of 19, 7.5% decrease in breast evaluation volume V{sub 50%}; P=.008). Conclusion: Significant changes in LC shape and volume at the time of boost that deviate from the original plan for WBI with sequential boost can be addressed by adaptive replanning at the first boost fraction.

Boosted objects and jet substructure at the LHC. Report of BOOST2012, held at IFIC Valencia, 23rd-27th of July 2012

International Nuclear Information System (INIS)

Altheimer, A.; Thompson, E.N.; Arce, A.; Bjergaard, D.; Asquith, L.; Backus Mayes, J.; Hook, A.; Izaguirre, E.; Jankowiak, M.; Larkoski, A.; Nef, P.; Schwartzman, A.; Swiatlowski, M.; Wacker, J.; Kuutmann, E.B.; Berger, J.; Bryngemark, L.; Buckley, A.; Debenedetti, C.; Butterworth, J.; Campanelli, M.; Davison, A.; Cacciari, M.; Carli, T.; Roeck, A. de; Chala, M.; Chapleau, B.; Chen, C.; Chou, J.P.; Cornelissen, T.; Fleischmann, S.; Curtin, D.; Dasgupta, M.; Almeida Dias, F. de; De Cosa, A.; Doglioni, C.; Guescini, F.; Ellis, S.D.; Hornig, A.; Scholtz, J.; Fassi, F.; Hoz, S.G. de la; Kaci, M.; Oliver Garcia, E.; Rodrigo, G.; Salt, J.; Sanchez Martinez, V.; Villaplana, M.; Vos, M.; Ferrando, J.; Kar, D.; Nordstrom, K.; Freytsis, M.; Gonzalez Silva, M.L.; Han, Z.; Lopez Mateos, D.; Schwartz, M.D.; Juknevich, J.; Kasieczka, G.; Plehn, T.; Schaetzel, S.; Takeuchi, M.; Kogler, R.; Loch, P.; Marzani, S.; Spannowsky, M.; Masetti, L.; Mateu, V.; Stewart, I.; Thaler, J.; Miller, D.W.; Mishra, K.; Tran, N.V.; Penwell, J.; Pilot, J.; Rappoccio, S.; Rizzi, A.; Safonov, A.; Salam, G.P.; Schioppa, M.; Schmidt, A.; Segala, M.; Son, M.; Soyez, G.; Strom, D.; Vermilion, C.; Walsh, J.

2014-01-01

This report of the BOOST2012 workshop presents the results of four working groups that studied key aspects of jet substructure. We discuss the potential of first-principle QCD calculations to yield a precise description of the substructure of jets and study the accuracy of state-of-the-art Monte Carlo tools. Limitations of the experiments' ability to resolve substructure are evaluated, with a focus on the impact of additional (pile-up) proton proton collisions on jet substructure performance in future LHC operating scenarios. A final section summarizes the lessons learnt from jet substructure analyses in searches for new physics in the production of boosted top quarks. (orig.)

Boosted objects and jet substructure at the LHC. Report of BOOST2012, held at IFIC Valencia, 23rd-27th of July 2012

Energy Technology Data Exchange (ETDEWEB)

Altheimer, A.; Thompson, E.N. [Columbia University, Nevis Laboratory, Irvington, NY (United States); Arce, A.; Bjergaard, D. [Duke University, Durham, NC (United States); Asquith, L. [Argonne National Laboratory, Lemont, IL (United States); Backus Mayes, J.; Hook, A.; Izaguirre, E.; Jankowiak, M.; Larkoski, A.; Nef, P.; Schwartzman, A.; Swiatlowski, M.; Wacker, J. [SLAC National Accelerator Laboratory, Menlo Park, CA (United States); Kuutmann, E.B. [Deutsches Elektronen-Synchrotron, DESY, Zeuthen (Germany); Humboldt University, Berlin (Germany); Berger, J. [Cornell University, Ithaca, NY (United States); Bryngemark, L. [Lund University, Lund (Sweden); Buckley, A.; Debenedetti, C. [University of Edinburgh, Edinburgh (United Kingdom); Butterworth, J.; Campanelli, M.; Davison, A. [University College London, London (United Kingdom); Cacciari, M. [CERN, Geneva 23 (Switzerland); Carli, T.; Roeck, A. de [LPTHE, UPMC Univ. Paris 6 et CNRS UMR, Paris (France); Chala, M. [CAFPE and Univ. of Granada, Granada (Spain); Chapleau, B. [McGill University, Montreal, QC (Canada); Chen, C. [Iowa State University, Ames, IA (United States); Chou, J.P. [Rutgers University, Piscataway, NJ (United States); Cornelissen, T.; Fleischmann, S. [Bergische Universitaet Wuppertal, Wuppertal (Germany); Curtin, D. [YITP, Stony Brook University, Stony Brook, NY (United States); Dasgupta, M. [University of Manchester, Manchester (United Kingdom); Almeida Dias, F. de [UNESP-Universidade Estadual Paulista, Sao Paulo (Brazil); De Cosa, A. [INFN, Naples (Italy); University of Naples, Naples (Italy); Doglioni, C.; Guescini, F. [University of Geneva, Geneva 4 (Switzerland); Ellis, S.D.; Hornig, A.; Scholtz, J. [University of Washington, Seattle, WA (United States); Fassi, F.; Hoz, S.G. de la; Kaci, M.; Oliver Garcia, E.; Rodrigo, G.; Salt, J.; Sanchez Martinez, V.; Villaplana, M.; Vos, M. [Instituto de Fisica Corpuscular, IFIC/CSIC-UVEG, Valencia (Spain); Ferrando, J.; Kar, D.; Nordstrom, K. [University of Glasgow, Glasgow (United Kingdom); Freytsis, M. [University of California, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); University of California, Berkeley, CA (United States); Gonzalez Silva, M.L. [Universidad de Buenos Aires, Buenos Aires (Argentina); Han, Z.; Lopez Mateos, D.; Schwartz, M.D. [Harvard University, Cambridge, MA (United States); Juknevich, J. [Weizmann Institute, Rehovot (Israel); Kasieczka, G.; Plehn, T.; Schaetzel, S.; Takeuchi, M. [Universitaet Heidelberg, Heidelberg (Germany); Kogler, R. [Universitaet Hamburg, Hamburg (Germany); Loch, P. [University of Arizona, Tucson, AZ (United States); Marzani, S.; Spannowsky, M. [IPPP, University of Durham, Durham (United Kingdom); Masetti, L. [Universitaet Mainz, Mainz (Germany); Mateu, V.; Stewart, I.; Thaler, J. [MIT, Cambridge, MA (United States); Miller, D.W. [University of Chicago, Chicago, IL (United States); Mishra, K.; Tran, N.V. [Fermi National Accelerator Laboratory, Batavia, IL (United States); Penwell, J. [Indiana University, Bloomington, IN (United States); Pilot, J. [University of California, Davis, CA (United States); Rappoccio, S. [Johns Hopkins University, Baltimore, MD (United States); University at Buffalo, State University of New York, Buffalo, NY (United States); Rizzi, A. [INFN, Pisa (Italy); University of Pisa, Pisa (Italy); Safonov, A. [Texas A and M University, College Station, TX (United States); Salam, G.P. [CERN, Geneva 23 (Switzerland); LPTHE, UPMC Univ. Paris 6 et CNRS UMR, Paris (France); Schioppa, M. [INFN, Rende (IT); University of Calabria, Rende (IT); Schmidt, A. [Universitaet Hamburg, Hamburg (DE); Universitaet Heidelberg, Heidelberg (DE); Segala, M. [Brown University, Richmond, RI (US); Son, M. [Yale University, New Haven, CT (US); Soyez, G. [CEA Saclay, Gif-sur-Yvette (FR); Strom, D. [University of Illinois, Chicago, IL (US); Vermilion, C. [University of California, Lawrence Berkeley National Laboratory, Berkeley, CA (US); Walsh, J. [University of California, Berkeley, CA (US)

2014-03-15

This report of the BOOST2012 workshop presents the results of four working groups that studied key aspects of jet substructure. We discuss the potential of first-principle QCD calculations to yield a precise description of the substructure of jets and study the accuracy of state-of-the-art Monte Carlo tools. Limitations of the experiments' ability to resolve substructure are evaluated, with a focus on the impact of additional (pile-up) proton proton collisions on jet substructure performance in future LHC operating scenarios. A final section summarizes the lessons learnt from jet substructure analyses in searches for new physics in the production of boosted top quarks. (orig.)

Protecting livelihoods, boosting food security in Kenya | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

2015-05-21

May 21, 2015 ... Protecting livelihoods, boosting food security in Kenya ... America, and the Caribbean with funds from the Government of Canada's fast-start financing. ... Water management and food security in vulnerable regions of China.

Precision, time, and cost: a comparison of three sampling designs in an emergency setting

Science.gov (United States)

Deitchler, Megan; Deconinck, Hedwig; Bergeron, Gilles

2008-01-01

The conventional method to collect data on the health, nutrition, and food security status of a population affected by an emergency is a 30 × 30 cluster survey. This sampling method can be time and resource intensive and, accordingly, may not be the most appropriate one when data are needed rapidly for decision making. In this study, we compare the precision, time and cost of the 30 × 30 cluster survey with two alternative sampling designs: a 33 × 6 cluster design (33 clusters, 6 observations per cluster) and a 67 × 3 cluster design (67 clusters, 3 observations per cluster). Data for each sampling design were collected concurrently in West Darfur, Sudan in September-October 2005 in an emergency setting. Results of the study show the 30 × 30 design to provide more precise results (i.e. narrower 95% confidence intervals) than the 33 × 6 and 67 × 3 design for most child-level indicators. Exceptions are indicators of immunization and vitamin A capsule supplementation coverage which show a high intra-cluster correlation. Although the 33 × 6 and 67 × 3 designs provide wider confidence intervals than the 30 × 30 design for child anthropometric indicators, the 33 × 6 and 67 × 3 designs provide the opportunity to conduct a LQAS hypothesis test to detect whether or not a critical threshold of global acute malnutrition prevalence has been exceeded, whereas the 30 × 30 design does not. For the household-level indicators tested in this study, the 67 × 3 design provides the most precise results. However, our results show that neither the 33 × 6 nor the 67 × 3 design are appropriate for assessing indicators of mortality. In this field application, data collection for the 33 × 6 and 67 × 3 designs required substantially less time and cost than that required for the 30 × 30 design. The findings of this study suggest the 33 × 6 and 67 × 3 designs can provide useful time- and resource-saving alternatives to the 30 × 30 method of data collection in emergency

Precision, time, and cost: a comparison of three sampling designs in an emergency setting

Directory of Open Access Journals (Sweden)

Deconinck Hedwig

2008-05-01

Full Text Available Abstract The conventional method to collect data on the health, nutrition, and food security status of a population affected by an emergency is a 30 × 30 cluster survey. This sampling method can be time and resource intensive and, accordingly, may not be the most appropriate one when data are needed rapidly for decision making. In this study, we compare the precision, time and cost of the 30 × 30 cluster survey with two alternative sampling designs: a 33 × 6 cluster design (33 clusters, 6 observations per cluster and a 67 × 3 cluster design (67 clusters, 3 observations per cluster. Data for each sampling design were collected concurrently in West Darfur, Sudan in September-October 2005 in an emergency setting. Results of the study show the 30 × 30 design to provide more precise results (i.e. narrower 95% confidence intervals than the 33 × 6 and 67 × 3 design for most child-level indicators. Exceptions are indicators of immunization and vitamin A capsule supplementation coverage which show a high intra-cluster correlation. Although the 33 × 6 and 67 × 3 designs provide wider confidence intervals than the 30 × 30 design for child anthropometric indicators, the 33 × 6 and 67 × 3 designs provide the opportunity to conduct a LQAS hypothesis test to detect whether or not a critical threshold of global acute malnutrition prevalence has been exceeded, whereas the 30 × 30 design does not. For the household-level indicators tested in this study, the 67 × 3 design provides the most precise results. However, our results show that neither the 33 × 6 nor the 67 × 3 design are appropriate for assessing indicators of mortality. In this field application, data collection for the 33 × 6 and 67 × 3 designs required substantially less time and cost than that required for the 30 × 30 design. The findings of this study suggest the 33 × 6 and 67 × 3 designs can provide useful time- and resource-saving alternatives to the 30 × 30 method of data

B-tagging in boosted h → b anti b decays

Energy Technology Data Exchange (ETDEWEB)

Jacobs, Ruth; Gaycken, Goetz; Hageboeck, Stephan; Kostyukhin, Vadim; Lenz, Tatjana; Schopf, Elisabeth; Toerne, Eckhard von; Wermes, Norbert [Physikalisches Institut, University of Bonn (Germany)

2015-07-01

The most likely decay channel of the standard model Higgs boson is the decay into a b- and an anti-b-quark. The properties of b-jets formed by the hadronization of b-quarks are essential input variables to all ATLAS h → b anti b analyses. In boosted topologies the performance of standard b-tagging algorithms is diminished due to the merging of close - by jets. The aim of the study presented is the optimization of a b-tagging algorithm for boosted h → b anti b decays using track jets with a smaller than standard cone radius. The study is based on simulated events containing boosted Higgs bosons from the decay of a new heavy gauge boson W{sup '} → Wh. A motivation for the use of track jets for b-tagging is the fact that the reconstructed jet axis for track jets more closely describes the b-hadron flight direction than for calorimeter jets. Using jets with a smaller cone radius allows to resolve topologies where larger radius jets are already merged.

SU-G-BRC-12: Isotoxic Dose Escalation for Advanced Lung Cancer: Comparison of Different Boosting Strategiesfor Patients with Recurrent Disease

Energy Technology Data Exchange (ETDEWEB)

Shusharina, N; Khan, F; Sharp, G; Choi, N [Massachusetts General Hospital, Boston, MA (United States)

2016-06-15

Purpose: To determine the dose level and timing of the boost in locally advanced lung cancer patients with confirmed tumor recurrence by comparing different boosting strategies by an impact of dose escalation in improvement of the therapeutic ratio. Methods: We selected eighteen patients with advanced NSCLC and confirmed recurrence. For each patient, a base IMRT plan to 60 Gy prescribed to PTV was created. Then we compared three dose escalation strategies: a uniform escalation to the original PTV, an escalation to a PET-defined target planned sequentially and concurrently. The PET-defined targets were delineated by biologically-weighed regions on a pre-treatment 18F-FDG PET. The maximal achievable dose, without violating the OAR constraints, was identified for each boosting method. The EUD for the target, spinal cord, combined lung, and esophagus was compared for each plan. Results: The average prescribed dose was 70.4±13.9 Gy for the uniform boost, 88.5±15.9 Gy for the sequential boost and 89.1±16.5 Gy for concurrent boost. The size of the boost planning volume was 12.8% (range: 1.4 – 27.9%) of the PTV. The most prescription-limiting dose constraints was the V70 of the esophagus. The EUD within the target increased by 10.6 Gy for the uniform boost, by 31.4 Gy for the sequential boost and by 38.2 for the concurrent boost. The EUD for OARs increased by the following amounts: spinal cord, 3.1 Gy for uniform boost, 2.8 Gy for sequential boost, 5.8 Gy for concurrent boost; combined lung, 1.6 Gy for uniform, 1.1 Gy for sequential, 2.8 Gy for concurrent; esophagus, 4.2 Gy for uniform, 1.3 Gy for sequential, 5.6 Gy for concurrent. Conclusion: Dose escalation to a biologically-weighed gross tumor volume defined on a pre-treatment 18F-FDG PET may provide improved therapeutic ratio without breaching predefined OAR constraints. Sequential boost provides better sparing of OARs as compared with concurrent boost.

SU-G-BRC-12: Isotoxic Dose Escalation for Advanced Lung Cancer: Comparison of Different Boosting Strategiesfor Patients with Recurrent Disease

International Nuclear Information System (INIS)

Shusharina, N; Khan, F; Sharp, G; Choi, N

2016-01-01

Purpose: To determine the dose level and timing of the boost in locally advanced lung cancer patients with confirmed tumor recurrence by comparing different boosting strategies by an impact of dose escalation in improvement of the therapeutic ratio. Methods: We selected eighteen patients with advanced NSCLC and confirmed recurrence. For each patient, a base IMRT plan to 60 Gy prescribed to PTV was created. Then we compared three dose escalation strategies: a uniform escalation to the original PTV, an escalation to a PET-defined target planned sequentially and concurrently. The PET-defined targets were delineated by biologically-weighed regions on a pre-treatment 18F-FDG PET. The maximal achievable dose, without violating the OAR constraints, was identified for each boosting method. The EUD for the target, spinal cord, combined lung, and esophagus was compared for each plan. Results: The average prescribed dose was 70.4±13.9 Gy for the uniform boost, 88.5±15.9 Gy for the sequential boost and 89.1±16.5 Gy for concurrent boost. The size of the boost planning volume was 12.8% (range: 1.4 – 27.9%) of the PTV. The most prescription-limiting dose constraints was the V70 of the esophagus. The EUD within the target increased by 10.6 Gy for the uniform boost, by 31.4 Gy for the sequential boost and by 38.2 for the concurrent boost. The EUD for OARs increased by the following amounts: spinal cord, 3.1 Gy for uniform boost, 2.8 Gy for sequential boost, 5.8 Gy for concurrent boost; combined lung, 1.6 Gy for uniform, 1.1 Gy for sequential, 2.8 Gy for concurrent; esophagus, 4.2 Gy for uniform, 1.3 Gy for sequential, 5.6 Gy for concurrent. Conclusion: Dose escalation to a biologically-weighed gross tumor volume defined on a pre-treatment 18F-FDG PET may provide improved therapeutic ratio without breaching predefined OAR constraints. Sequential boost provides better sparing of OARs as compared with concurrent boost.

Cooperatives boost opportunities for Moroccan women | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

2010-10-22

Oct 22, 2010 ... Cooperatives boost opportunities for Moroccan women. October 22 ... Substantial support for argan oil development continues with a €12 million grant. Half comes from the ... Research aims to identify and remove barriers faced by Africa's women entrepreneurs ... Solutions. Careers · Contact Us · Site map.

Heterologous Prime-Boost HIV-1 Vaccination Regimens in Pre-Clinical and Clinical Trials

Directory of Open Access Journals (Sweden)

Julia L. Hurwitz

2010-02-01

Full Text Available Currently, there are more than 30 million people infected with HIV-1 and thousands more are infected each day. Vaccination is the single most effective mechanism for prevention of viral disease, and after more than 25 years of research, one vaccine has shown somewhat encouraging results in an advanced clinical efficacy trial. A modified intent-to-treat analysis of trial results showed that infection was approximately 30% lower in the vaccine group compared to the placebo group. The vaccine was administered using a heterologous prime-boost regimen in which both target antigens and delivery vehicles were changed during the course of inoculations. Here we examine the complexity of heterologous prime-boost immunizations. We show that the use of different delivery vehicles in prime and boost inoculations can help to avert the inhibitory effects caused by vector-specific immune responses. We also show that the introduction of new antigens into boost inoculations can be advantageous, demonstrating that the effect of ‘original antigenic sin’ is not absolute. Pre-clinical and clinical studies are reviewed, including our own work with a three-vector vaccination regimen using recombinant DNA, virus (Sendai virus or vaccinia virus and protein. Promising preliminary results suggest that the heterologous prime-boost strategy may possibly provide a foundation for the future prevention of HIV-1 infections in humans.

Design of High Efficient MPPT Solar Inverter

Directory of Open Access Journals (Sweden)

Sunitha K. A.

2017-01-01

Full Text Available This work aims to design a High Efficient Maximum Power Point Tracking (MPPT Solar Inverter. A boost converter is designed in the system to boost the power from the photovoltaic panel. By this experimental setup a room consisting of 500 Watts load (eight fluorescent tubes is completely controlled. It is aimed to decrease the maintenance cost. A microcontroller is introduced for tracking the P&O (Perturb and Observe algorithm used for tracking the maximum power point. The duty cycle for the operation of the boost convertor is optimally adjusted by using MPPT controller. There is a MPPT charge controller to charge the battery as well as fed to inverter which runs the load. Both the P&O scheme with the fixed variation for the reference current and the intelligent MPPT algorithm were able to identify the global Maximum power point, however the performance of the MPPT algorithm was better.

A new interleaved double-input three-level boost converter

DEFF Research Database (Denmark)

Chen, Jianfei; Hou, Shiying; Sun, Tao

2016-01-01

This paper proposes a new interleaved double-input three-level Boost (DITLB) converter, which is composed of two boost converters indirectly in series. Thus, a high voltage gain, together with a low component stress and a small input current ripple due to the interleaved control scheme, is achieved....... The operating principle of the DITLB converter under the individual supplying power (ISP) and simultaneous supplying power (SSP) mode is analyzed. In addition, closed-loop control strategies composed of a voltage-current loop and a voltage-balance loop, have been researched to make the converter operate...... steadily and to alleviate the neutral-point imbalance issue. Experimental results verify correctness and feasibility of the proposed topology and control strategies....

The use of stereotactic radiosurgical boost in the treatment of medulloblastomas

International Nuclear Information System (INIS)

Woo, Charles; Stea, Baldassarre; Lulu, Bruce; Hamilton, Allan; Cassady, J. Robert

1997-01-01

Purpose: Starting in 1992, we began using a stereotactic radiosurgical (SRS) boost for the treatment of medulloblastomas. Four patients ranging in age from 7 to 42 years old have since been treated and are the subject of this retrospective study. Methods and Materials: All patients were initially treated with a maximally debulking surgery and external beam radiotherapy, which were then followed by a stereotactic radiosurgical boost using a modified 6 MeV linear accelerator. Radiosurgical boost doses ranged from 4.50 to 10.0 Gy. Target volumes ranged from 1.1 to 8.1 cc. The procedure was well tolerated with minimal acute toxicities. Results: All four patients are alive without evidence of recurrence (at 8 to 35 months). Acute nausea and vomiting was elicited during the radiosurgical procedure in the first patient treated. We have since begun premedicating patients with antiemetics or treating under general anesthesia. Late complications consisted of panhypopituitarism in one patient, which was thought to be attributable to the previous course of whole-brain radiotherapy. We have not observed any incidence of radionecrosis in this small cohort of patients. Conclusions: Our preliminary results with the use of radiosurgery for medulloblastomas are optimistic, and we would like to suggest the inclusion of a radiosurgery boost in future clinical trials for treatment of this disease

Design Guidelines of a Spring-Damper System for Emergency Diesel Generator Sets

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Kyu; Choun, Young Sun; Seo, Jeong Moon

2007-05-15

This guidelines described about the procedure of isolation system design for Emergency Diesel Generator (EDG) of Nuclear Power Plant (NPP). First of all, a vibration concept including the ground vibration was described and vibration control system and seismic isolation system were considered. The behavior characteristics and design consideration of coil spring-viscose damper system were summarized. The material properties of foundation of EDG system and the ground were considered. A design load and seismic load for isolation system design were described and an analysis method was explained. Finally, a design example for an EDG in Yonggwang Nuclear Unit 5 and 6 was attached of Appendix. First of all, this design guideline can apply to design of a vibration and seismic isolation system for EDG system and the design example present a design procedure practically. Moreover, this design guideline can be used for isolation design of other rotational machines and other isolation system except spring-damper system.

Concurrent Boost with Adjuvant Breast Hypofractionated Radiotherapy and Toxicity Assessment

Directory of Open Access Journals (Sweden)

Mona M. Sayed

2015-01-01

Full Text Available Background: The use of shorter radiotherapy schedules has an economic and logistic advantage for radiotherapy departments, as well as a high degree of patient convenience. The aim of this study is to assess the acute and short-term late toxicities of a hypofractionated radiotherapy schedule with a concomitant boost. Methods: We enrolled 57 eligible patients as group A. These patients received 42.5 Gy in 16 fractions of 2.66 Gy each to the whole breast over 3.2 weeks. A concomitant electron boost of 12 Gy in 16 fractions was also administered which gave an additional 0.75 Gy daily to the lumpectomy area for a total radiation dose of 54.5 Gy. Toxicity was recorded at three weeks and at three months for this group as well as for a control group (group B. The control group comprised 76 eligible patients treated conventionally with 50 Gy to the whole breast over five weeks followed by a sequential electron boost of 12 Gy in 2 Gy per fraction. Results: There were no statistically significant differences observed in the incidence of acute skin toxicity, breast pain, and edema recorded at three weeks or pigmentation and fibrosis recorded at three months between the two groups (P0.05. Conclusion: The results of this study suggest there are no increased acute and shortterm late toxicities affiliated with the hypofractionated schedule plus a concomitant boost as prescribed compared to the conventional fractionation of adjuvant breast radiotherapy. Large randomized trials and long-term follow-up are needed to confirm these favorable findings.

Boosting youth employment in agri-business | IDRC - International ...

International Development Research Centre (IDRC) Digital Library (Canada)

Boosting youth employment in agri-business ... economic importance and could provide jobs for women and youth while increasing food security. ... “The main challenge youth face is poor access to credit and extension services,” she says.

Boosted protease inhibitor monotherapy versus boosted protease inhibitor plus lamivudine dual therapy as second-line maintenance treatment for HIV-1-infected patients in sub-Saharan Africa (ANRS12 286/MOBIDIP): a multicentre, randomised, parallel, open-label, superiority trial.

Science.gov (United States)

Ciaffi, Laura; Koulla-Shiro, Sinata; Sawadogo, Adrien Bruno; Ndour, Cheik Tidiane; Eymard-Duvernay, Sabrina; Mbouyap, Pretty Rosereine; Ayangma, Liliane; Zoungrana, Jacques; Gueye, Ndeye Fatou Ngom; Diallo, Mohamadou; Izard, Suzanne; Bado, Guillaume; Kane, Coumba Toure; Aghokeng, Avelin Fobang; Peeters, Martine; Girard, Pierre Marie; Le Moing, Vincent; Reynes, Jacques; Delaporte, Eric

2017-09-01

(tenofovir and lamivudine) were reintroduced into treatment. The primary outcome was the proportion of participants who had treatment failure at 96 weeks in the intention-to-treat analysis, where treatment failure was defined as one of the following: a confirmed viral load of more than 500 copies per mL, reintroduction of NRTI, or interruption of boosted protease inhibitor. We designed the study to detect a difference of 12% between groups in the primary outcome, with an expected 20% of patients having treatment failure in the monotherapy group. This study is registered with ClinicalTrials.gov, number NCT01905059. Between March 5, 2014, and Jan 26, 2015, 265 participants were assigned to receive monotherapy (133) or boosted protease inhibitor plus lamivudine (132). At week 48, an independent data safety monitoring board reviewed data, and advised discontinuation of the monotherapy group because the number of failures had exceeded the expected 20%; therefore results here are for week 48. At this point, treatment failure occurred in four (3·0%; 95% CI 0·8-7·6) of 132 participants on dual therapy and 33 (24·8%; 17·7-33·0) of 133 participants on monotherapy (relative risk 8·2, 95% CI 3·0-22·5; odds ratio 10·6, 95% CI 3·6-42·1). The difference between groups (21·8%, 95% CI 13·9-29·7; ptreatment failure. Results indicated that boosted protease inhibitor monotherapy cannot be recommended for these patients. Agence National de Recherche sur le Sida et les hépatites and Janssen Pharmaceutica. Copyright © 2017 Elsevier Ltd. All rights reserved.

Physical design correlates of efficiency and safety in emergency departments: a qualitative examination.

Science.gov (United States)

Pati, Debajyoti; Harvey, Thomas E; Pati, Sipra

2014-01-01

The objective of this study was to explore and identify physical design correlates of safety and efficiency in emergency department (ED) operations. This study adopted an exploratory, multimeasure approach to (1) examine the interactions between ED operations and physical design at 4 sites and (2) identify domains of physical design decision-making that potentially influence efficiency and safety. Multidisciplinary gaming and semistructured interviews were conducted with stakeholders at each site. Study data suggest that 16 domains of physical design decisions influence safety, efficiency, or both. These include (1) entrance and patient waiting, (2) traffic management, (3) subwaiting or internal waiting areas, (4) triage, (5) examination/treatment area configuration, (6) examination/treatment area centralization versus decentralization, (7) examination/treatment room standardization, (8) adequate space, (9) nurse work space, (10) physician work space, (11) adjacencies and access, (12) equipment room, (13) psych room, (14) staff de-stressing room, (15) hallway width, and (16) results waiting area. Safety and efficiency from a physical environment perspective in ED design are mutually reinforcing concepts--enhancing efficiency bears positive implications for safety. Furthermore, safety and security emerged as correlated concepts, with security issues bearing implications for safety, thereby suggesting important associations between safety, security, and efficiency.

Crew emergency return vehicle - Electrical power system design study

Science.gov (United States)

Darcy, E. C.; Barrera, T. P.

1989-01-01

A crew emergency return vehicle (CERV) is proposed to perform the lifeboat function for the manned Space Station Freedom. This escape module will be permanently docked to Freedom and, on demand, will be capable of safely returning the crew to earth. The unique requirements that the CERV imposes on its power source are presented, power source options are examined, and a baseline system is selected. It consists of an active Li-BCX DD-cell modular battery system and was chosen for the maturity of its man-rated design and its low development costs.

Long-Term Results of Targeted Intraoperative Radiotherapy (Targit) Boost During Breast-Conserving Surgery

Energy Technology Data Exchange (ETDEWEB)

Vaidya, Jayant S., E-mail: jayant.vaidya@ucl.ac.uk [Research Department of Surgery, Division of Surgery and Interventional Science, University College London, London (United Kingdom); Baum, Michael [Research Department of Surgery, Division of Surgery and Interventional Science, University College London, London (United Kingdom); Tobias, Jeffrey S. [Department of Radiation Oncology, University College London Hospitals, London (United Kingdom); Wenz, Frederik [Radiation Oncology and Gynaecology, University Medical Centre of Mannheim (Germany); Massarut, Samuele [Surgery and Radiation Oncology, Centro di Riferimento Oncologico (CRO), Aviano (Italy); Keshtgar, Mohammed [Research Department of Surgery, Division of Surgery and Interventional Science, University College London, London (United Kingdom); Hilaris, Basil [Radiation Oncology, Our Lady of Mercy, New York Medical College, New York (United States); Saunders, Christobel [Institute of Health and Rehabilitation Research, University of Notre Dame, Fremantle, Western Australia (Australia); Williams, Norman R.; Brew-Graves, Chris [Research Department of Surgery, Division of Surgery and Interventional Science, University College London, London (United Kingdom); Corica, Tammy [Institute of Health and Rehabilitation Research, University of Notre Dame, Fremantle, Western Australia (Australia); Roncadin, Mario [Surgery and Radiation Oncology, Centro di Riferimento Oncologico (CRO), Aviano (Italy); Kraus-Tiefenbacher, Uta; Suetterlin, Marc [Radiation Oncology and Gynaecology, University Medical Centre of Mannheim (Germany); Bulsara, Max [Institute of Health and Rehabilitation Research, University of Notre Dame, Fremantle, Western Australia (Australia); Joseph, David [Radiation Oncology, Sir Charles Gairdner Hospital and School of Surgery, University of Western Australia, Perth (Australia)

2011-11-15

Purpose: We have previously shown that delivering targeted radiotherapy to the tumour bed intraoperatively is feasible and desirable. In this study, we report on the feasibility, safety, and long-term efficacy of TARGeted Intraoperative radioTherapy (Targit), using the Intrabeam system. Methods and Materials: A total of 300 cancers in 299 unselected patients underwent breast-conserving surgery and Targit as a boost to the tumor bed. After lumpectomy, a single dose of 20 Gy was delivered intraoperatively. Postoperative external beam whole-breast radiotherapy excluded the usual boost. We also performed a novel individualized case control (ICC) analysis that computed the expected recurrences for the cohort by estimating the risk of recurrence for each patient using their characteristics and follow-up period. Results: The treatment was well tolerated. The median follow up was 60.5 months (range, 10-122 months). Eight patients have had ipsilateral recurrence: 5-year Kaplan Meier estimate for ipsilateral recurrence is 1.73% (SE 0.77), which compares well with that seen in the boosted patients in the European Organization for Research and Treatment of Cancer study (4.3%) and the UK STAndardisation of breast RadioTherapy study (2.8%). In a novel ICC analysis of 242 of the patients, we estimated that there should be 11.4 recurrences; in this group, only 6 recurrences were observed. Conclusions: Lumpectomy and Targit boost combined with external beam radiotherapy results in a low local recurrence rate in a standard risk patient population. Accurate localization and the immediacy of the treatment that has a favorable effect on tumour microenvironment may contribute to this effect. These long-term data establish the long-term safety and efficacy of the Targit technique and generate the hypothesis that Targit boost might be superior to an external beam boost in its efficacy and justifies a randomized trial.

Targeted intraoperative radiotherapy (TARGIT) yields very low recurrence rates when given as a boost

International Nuclear Information System (INIS)

Vaidya, Jayant S.; Baum, Michael; Tobias, Jeffrey S.; Massarut, Samuele; Wenz, Frederik; Murphy, Olive; Hilaris, Basil; Houghton, Joan B.Sc.; Saunders, Christobel; Corica, Tammy; Roncadin, Mario; Kraus-Tiefenbacher, Uta; Melchaert, Frank; Keshtgar, Mohammed; Sainsbury, Richard; Douek, Michael; Harrison, Elly; Thompson, Alastair; Joseph, David

2006-01-01

Purpose: Patients undergoing breast-conserving surgery were offered boost radiotherapy with targeted intraoperative radiotherapy (TARGIT) using the Intrabeam system to test the feasibility, safety, and efficacy of the new approach. Methods and Materials: We treated 302 cancers in 301 unselected patients. This was not a low-risk group. One-third of patients (98/301) were younger than 51 years of age. More than half of the tumors (172, 57%) were between 1 cm and 2 cm, and one-fifth (62, 21%) were >2 cm; 29% (86) had a Grade 3 tumor and, in 29% (87), axillary lymph nodes contained metastasis. After primary surgery, 20 Gy was delivered intraoperatively to the surface of the tumor bed, followed by external-beam radiotherapy (EBRT), but excluding the usual boost. Results: The treatment was well tolerated. The follow-up ranged from 3 to 80 months (164 and 90 patients completed 2 and 3 years follow-up, respectively). Four patients (1.3%) had local recurrence. The Kaplan-Meier estimate of local recurrence is 2.6% (SE = 1.7) at 5 years. This compares favorably with the 4.3% recurrence rate in boosted patients from the EORTC boost study, in which only 8.1% patients were node-positive, as opposed to 29% in our series. Conclusion: Targeted intraoperative radiotherapy combined with EBRT results in a low local recurrence rate. This could be attributed to both accurate targeting and timeliness of the treatment. These data support the need for a randomized trial to test whether the TARGIT boost is superior to conventional external boost, especially in high-risk women

A two-dose heterologous prime-boost vaccine regimen eliciting sustained immune responses to Ebola Zaire could support a preventive strategy for future outbreaks.

Science.gov (United States)

Shukarev, Georgi; Callendret, Benoit; Luhn, Kerstin; Douoguih, Macaya

2017-02-01

The consequences of the 2013-16 Ebola Zaire virus disease epidemic in West Africa were grave. The economies, healthcare systems and communities of Guinea, Sierra Leone and Liberia were devastated by over 18 months of active Ebola virus transmission, followed by sporadic resurgences potentially related to sexual transmission by survivors with viral persistence in body fluids following recovery. The need to develop and implement strategies to prevent and mitigate future outbreaks is now beyond dispute. The potential for unpredictable outbreaks of indeterminate duration, and control challenges posed by the possibility of sporadic re-emergence, mean that implementation of an effective vaccination program for outbreak containment necessitates a vaccine providing durable immunity. Heterologous prime-boost vaccine regimens deliver the same or similar antigens through different vaccine types, the first to prime and the second to boost the immune system. Ad26.ZEBOV/MVA-BN-Filo is an investigational Ebola Zaire vaccine regimen that uses this heterologous prime-boost approach. Preliminary Phase 1 data suggest that Ad26.ZEBOV/MVA-BN-Filo confers durable immunity for at least 240 d and is well-tolerated with a good safety profile. This regimen may therefore be suitable for prophylactic use in a regional or targeted population vaccination strategy, and could potentially aid prevention and control of future Ebola outbreaks.

Boosted performance of a compression-ignition engine with a displaced piston

Science.gov (United States)

Moore, Charles S; Foster, Hampton H

1936-01-01

Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury.

A New Method of Cloud Detection Based on Cascaded AdaBoost

International Nuclear Information System (INIS)

Ma, C; Chen, F; Liu, J; Duan, J

2014-01-01

Cloud detection of remote sensing image is a critical step in the processing of the remote sensing images. How to quickly, accurately and effectively detect cloud on remote sensing images, is still a challenging issue in this area. In order to avoid disadvantages of the current algorithms, the cascaded AdaBoost classifier algorithm is successfully applied to the cloud detection. A new algorithm combined cascaded AdaBoost classifier and multi-features, is proposed in this paper. First, multi-features based on the color, texture and spectral features are extracted from the remote sensing image. Second, the automatic cloud detection model is obtained based on the cascaded AdaBoost algorithm. In this paper, the results show that the new algorithm can determine cloud detection model and threshold values adaptively for different resolution remote sensing training data. The accuracy of cloud detection is improved. So it is a new effective algorithm for the cloud detection of remote sensing images

Conceptual design of an emergency tritium clean-up system

International Nuclear Information System (INIS)

Muller, M.E.

1978-01-01

The Los Alamos Scientific Laboratory (LASL) has been selected by the Department of Energy (DOE) to design, build, and operate a facility to demonstrate the operability of the tritium-related subsystems that would be required to successfully develop fusion reactor systems. An emergency tritium clean-up subsystem (ETC) for this facility will be designed to remove tritium from the cell atmosphere if an accident causes the primary and secondary tritium containment to be breached. Conceptually, the ETC will process cell air at the rate of 0.65 actual m 3 /s and will achieve an overall decontamination factor of 10 6 per tritium oxide (T 2 O). Following the maximum credible release of 100 g of tritium, the ETC will restore the cell to opertional status within 24 h without a significant release of tritium to the environment

Impact of Boost Radiation in the Treatment of Ductal Carcinoma In Situ: A Population-Based Analysis

Energy Technology Data Exchange (ETDEWEB)

Rakovitch, Eileen, E-mail: Eileen.rakovitch@sunnybrook.ca [Sunnybrook Health Sciences Centre, 2075 Bayview Avenue, Toronto, Ontario (Canada); Institute for Clinical Evaluative Sciences, Toronto, Ontario (Canada); University of Toronto, Toronto, Ontario (Canada); Narod, Steven A. [University of Toronto, Toronto, Ontario (Canada); Women’s College Research Institute, Toronto, Ontario (Canada); Nofech-Moses, Sharon; Hanna, Wedad [Sunnybrook Health Sciences Centre, 2075 Bayview Avenue, Toronto, Ontario (Canada); University of Toronto, Toronto, Ontario (Canada); Thiruchelvam, Deva; Saskin, Refik; Taylor, Carole [Institute for Clinical Evaluative Sciences, Toronto, Ontario (Canada); Tuck, Alan [London Health Sciences Center, London, Ontario (Canada); Youngson, Bruce; Miller, Naomi; Done, Susan J. [University Health Network, Toronto, Ontario (Canada); Sengupta, Sandip [Kingston General Hospital, Kingston, Ontario (Canada); Elavathil, Leela [University of Toronto, Toronto, Ontario (Canada); Henderson General Hospital, 711 Concession Street, Hamilton, Ontario (Canada); Jani, Prashant A. [University of Toronto, Toronto, Ontario (Canada); Regional Health Sciences Centre, Thunder Bay, Ontario (Canada); Bonin, Michel [Sudbury Regional Hospital, Sudbury, Ontario (Canada); Metcalfe, Stephanie [Sunnybrook Health Sciences Centre, 2075 Bayview Avenue, Toronto, Ontario (Canada); Paszat, Lawrence [Sunnybrook Health Sciences Centre, 2075 Bayview Avenue, Toronto, Ontario (Canada); Institute for Clinical Evaluative Sciences, Toronto, Ontario (Canada); University of Toronto, Toronto, Ontario (Canada)

2013-07-01

Purpose: To report the outcomes of a population of women with ductal carcinoma in situ (DCIS) treated with breast-conserving surgery and radiation and to evaluate the independent effect of boost radiation on the development of local recurrence. Methods and Materials: All women diagnosed with DCIS and treated with breast-conserving surgery and radiation therapy in Ontario from 1994 to 2003 were identified. Treatments and outcomes were identified through administrative databases and validated by chart review. The impact of boost radiation on the development of local recurrence was determined using survival analyses. Results: We identified 1895 cases of DCIS that were treated by breast-conserving surgery and radiation therapy; 561 patients received boost radiation. The cumulative 10-year rate of local recurrence was 13% for women who received boost radiation and 12% for those who did not (P=.3). The 10-year local recurrence-free survival (LRFS) rate among women who did and who did not receive boost radiation was 88% and 87%, respectively (P=.27), 94% and 93% for invasive LRFS (P=.58), and was 95% and 93% for DCIS LRFS (P=.31). On multivariable analyses, boost radiation was not associated with a lower risk of local recurrence (hazard ratio = 0.82, 95% confidence interval 0.59-1.15) (P=.25). Conclusions: Among a population of women treated with breast-conserving surgery and radiation for DCIS, additional (boost) radiation was not associated with a lower risk of local or invasive recurrence.

User's design handbook for a Standardized Control Module (SCM) for DC to DC Converters, volume 2

Science.gov (United States)

Lee, F. C.

1980-01-01

A unified design procedure is presented for selecting the key SCM control parameters for an arbitrarily given power stage configuration and parameter values, such that all regulator performance specifications can be met and optimized concurrently in a single design attempt. All key results and performance indices, for buck, boost, and buck/boost switching regulators which are relevant to SCM design considerations are included to facilitate frequent references.

Can we predict Acute Medical readmissions using the BOOST tool? A retrospective case note review.

Science.gov (United States)

Lee, Geraldine A; Freedman, Daniel; Beddoes, Penelope; Lyness, Emily; Nixon, Imogen; Srivastava, Vivek

2016-01-01

Readmissions within 30-days of hospital discharge are a problem. The aim was to determine if the Better Outcomes for Older Adults through Safe Transitions (BOOST) risk assessment tool was applicable within the UK. Patients over 65 readmitted were identified retrospectively via a casenote review. BOOST assessment was applied with 1 point for each risk factor. 324 patients were readmitted (mean age 77 years) with a median of 7 days between discharge and readmission. The median BOOST score was 3 (IQR 2-4) with polypharmacy evident in 88% and prior hospitalisation in 70%. The tool correctly predicted 90% of readmissions using two or more risk factors and 99.1% if one risk factor was included. The BOOST assessment tool appears appropriate in predicting readmissions however further analysis is required to determine its precision.

Buck-Boost DC-DC Converter Control by Using the Extracted Model from Signal Flow Graph Method

OpenAIRE

Mohammadian, Leila; Babaei, Ebrahim; Bannae Sharifian, Mohammad Bagher

2015-01-01

In this paper, the signal flow graph technique and Mason gain formula are applied for extracting the model and transfer functions from control to output and from input to output of a buck-boost converter. In order to investigate a controller necessity for the converter of assumed parameters, the frequency and time domain analysis are done and the open loop system characteristics are verified and the needed closed loop controlled system specifications are determined. Finally designing a contro...

Searches with boosted objects at ATLAS and CMS

CERN Document Server

Moran, Dermot Anthony

2018-01-01

An overview of searches for beyond the standard model physics using boosted objects is presented. The searches are based on proton-proton collision data collected with the ATLAS and CMS detectors at the LHC during the 2015 and 2016 running periods.

Enhancing treatment of osteoarthritis knee pain by boosting expectancy: A functional neuroimaging study

Directory of Open Access Journals (Sweden)

Jian Kong

Full Text Available Objectives: Expectation can significantly modulate pain and treatment effects. This study aims to investigate if boosting patients' expectancy can enhance the treatment of knee osteoarthritis (KOA, and its underlying brain mechanism. Methods: Seventy-four KOA patients were recruited and randomized to three groups: boosted acupuncture (with a manipulation to enhance expectation, standard acupuncture, or treatment as usual (TAU. Each patient underwent six treatments before being debriefed, and four additional treatments after being debriefed. The fMRI scans were applied during the first and sixth treatment sessions. Results: We found significantly decreased knee pain in the boosted acupuncture group compared to the standard acupuncture or TAU groups after both six and ten treatments. Resting state functional connectivity (rsFC analyses using the nucleus accumbens (NAc as the seed showed rsFC increases between the NAc and the medial prefrontal cortex (MPFC/rostral anterior cingulate cortex (rACC and dorsolateral prefrontal cortex in the boosted group as compared to the standard acupuncture group after multiple treatments. Expectancy scores after the first treatment were significantly associated with increased NAc-rACC/MPFC rsFC and decreased knee pain following treatment. Conclusions: Our study provides a novel method and mechanism for boosting the treatment of pain in patients with KOA. Our findings may shed light on enhancing outcomes of pharmacological and integrative medicines in clinical settings. Keywords: Knee osteoarthritis, Expectancy, Acupuncture, Reward, Resting state functional connectivity

Emergency lighting system for compliance with the IS-30 and further than the foundations of design events

International Nuclear Information System (INIS)

Tejeda Sanchez, C.

2014-01-01

Autonomy and vulnerability to fire requirements of the emergency lighting systems, established in CSN instruction IS-30, and in commitments to deal with the consequences of events more beyond the bases of design, the design of a new lighting system required of emergency in the Almaraz Nuclear power plant. The design process consists of three phases: study of needs, definition of detailed design and requirements. During these phases is defined distribution and models luminaire lighting studies and specifications. Through the adaptation of the system to the needs of each area of the plant is It achieves compliance with the objectives defined by the CSN. (Author)

Characterization of the antigen-specific CD4+ T cell response induced by prime-boost strategies with CAF01 and CpG adjuvants administered by the intranasal and subcutaneous routes

Directory of Open Access Journals (Sweden)

Annalisa eCiabattini

2015-08-01

Full Text Available The design of heterologous prime-boost vaccine combinations that optimally shape the immune response is of critical importance for the development of next generation vaccines. Here we tested different prime-boost combinations using the tuberculosis vaccine antigen H56 with CAF01 or CpG ODN 1821 adjuvants, administered by the parenteral and nasal routes. By using peptide-MHC class II tetramers, antigen-specific CD4+ T cells were tracked following primary and booster immunizations. Both parenteral priming with H56 plus CAF01 and nasal priming with H56 plus CpG elicited significant expansion of CD4+ tetramer-positive T cells in the spleen, however only parenterally primed cells responded to booster immunization. Subcutaneous priming with H56 and CAF01 followed by nasal boosting with H56 and CpG showed the greater expansion of CD4+ tetramer-positive T cells in the spleen and lungs compared to all the other homologous and heterologous prime-boost combinations. Nasal boosting exerted a recruitment of primed CD4+ T cells into lungs that was stronger in subcutaneously than nasally primed mice, in accordance with different chemokine receptor expression induced by primary immunization. These data demonstrate that subcutaneous priming is fundamental for eliciting CD4+ T cells that can be efficiently boosted by the nasal route and results in the recruitment of antigen-experienced cells into the lungs. Combination of different vaccine formulations and routes of delivery for priming and boosting is a strategic approach for improving and directing vaccine-induced immune responses.

Boosted structured additive regression for Escherichia coli fed-batch fermentation modeling.

Science.gov (United States)

Melcher, Michael; Scharl, Theresa; Luchner, Markus; Striedner, Gerald; Leisch, Friedrich

2017-02-01

The quality of biopharmaceuticals and patients' safety are of highest priority and there are tremendous efforts to replace empirical production process designs by knowledge-based approaches. Main challenge in this context is that real-time access to process variables related to product quality and quantity is severely limited. To date comprehensive on- and offline monitoring platforms are used to generate process data sets that allow for development of mechanistic and/or data driven models for real-time prediction of these important quantities. Ultimate goal is to implement model based feed-back control loops that facilitate online control of product quality. In this contribution, we explore structured additive regression (STAR) models in combination with boosting as a variable selection tool for modeling the cell dry mass, product concentration, and optical density on the basis of online available process variables and two-dimensional fluorescence spectroscopic data. STAR models are powerful extensions of linear models allowing for inclusion of smooth effects or interactions between predictors. Boosting constructs the final model in a stepwise manner and provides a variable importance measure via predictor selection frequencies. Our results show that the cell dry mass can be modeled with a relative error of about ±3%, the optical density with ±6%, the soluble protein with ±16%, and the insoluble product with an accuracy of ±12%. Biotechnol. Bioeng. 2017;114: 321-334. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Black brane entropy and hydrodynamics: The boost-invariant case

International Nuclear Information System (INIS)

Booth, Ivan; Heller, Michal P.; Spalinski, Michal

2009-01-01

The framework of slowly evolving horizons is generalized to the case of black branes in asymptotically anti-de Sitter spaces in arbitrary dimensions. The results are used to analyze the behavior of both event and apparent horizons in the gravity dual to boost-invariant flow. These considerations are motivated by the fact that at second order in the gradient expansion the hydrodynamic entropy current in the dual Yang-Mills theory appears to contain an ambiguity. This ambiguity, in the case of boost-invariant flow, is linked with a similar freedom on the gravity side. This leads to a phenomenological definition of the entropy of black branes. Some insights on fluid/gravity duality and the definition of entropy in a time-dependent setting are elucidated.

Enhanced Buck-Boost Three-Level Neutral-Point-Clamped Inverters

DEFF Research Database (Denmark)

Tan, K. K.; Gao, F.; Chiang Loh, Poh

2009-01-01

In traditional three-level neutral-point-clamped (NPC) inverters, a major issue is capacitor voltage imbalance, which results in low order harmonics. The compensation of the capacitor voltages often require additional control complexity, which cannot be conveniently implemented. The "alternative...... phase opposition disposition" (APOD) modulation method used in traditional NPC topologies also has lower harmonics performance as compared to the "phase disposition" (PD) modulation method.In this paper, we introduce a new three-level NPC topology that utilises the harmonically superior PD modulation...... method, with the ability to easily adjust for capacitor voltage imbalances. To further improve the boost capability of the three-level NPC inverters, another new topology introduces 2 additional diodes,achieving higher boost performance while totally eliminating thepossibility of capacitor voltage...

Ultrasensitive superconducting terahertz detectors: novel approaches and emerging materials

International Nuclear Information System (INIS)

Sergeev, Andrei; Mitin, Vladimir; Karasik, Boris; Vitkalov, Sergey

2014-01-01

Novel approaches to THz sensing based superconductor detectors and emerging superconducting nanomaterials have a strong potential to boost development of advanced optoelectronic devices, such as THz detectors, THz mixers, single photon counters and quantum calorimeters with outstanding sensitivity. Such devices have a number of applications in THZ environmental and industrial monitoring, astrophysics, homeland security, and medicine. Single photon counters have potential as key elements for optical communication and networking, quantum imaging and metrology, quantum optical computing and bio-photonics, and single-molecule spectroscopy

Voltage regulation of the Y-source boost DC-DC converter considering effects of leakage inductances based on cascaded sliding-mode control

DEFF Research Database (Denmark)

Ahmadzadeh, Soheil; Markadeh, Gholamreza Arab; Blaabjerg, Frede

2017-01-01

In this study, a sliding mode-based controller is designed for regulating the output voltage of a high step-up DC-DC converter with three coupled inductors called Y-source impedance network. As Y-source converter can provide a very high boost at a lower shoot-through duty cycle of the switch...

Boosted Higgs boson tagging using jet substructures

CERN Document Server

Shvydkin, Pavel

2016-01-01

Searching BSM particles via the Higgs boson final state has now become common. The mass of desired BSM particle is more than 1 TeV, thereby its decay products are highly Lorentz-boosted. Hence the jets from b quark-antiquark pair - which the Higgs boson mostly decays into - are very closed to each other, and merged into one jet, that is typically reconstructed using large jet sizes (∆R = 0.8). In this work regression technique is applied to AK8 jets (which defined by anti-kT algorithm, using ΔR = 0.8). The regression makes use of boosted jets with substructure information, coupled with the pecularities of a b quark decay, like the presence of a soft lepton (SL) inside the jet. It has allowed to improve the resolution of the mass reconstruction and transverse momentum of the Higgs boson. This application results in improvement of the mass reconstruction by 3-4 percent. These result may be improved firstly by making more careful pileup rejection. Then it is possible to combine base regression train for dif...

Methodology, Algorithms, and Emerging Tool for Automated Design of Intelligent Integrated Multi-Sensor Systems

Directory of Open Access Journals (Sweden)

Andreas König

2009-11-01

Full Text Available The emergence of novel sensing elements, computing nodes, wireless communication and integration technology provides unprecedented possibilities for the design and application of intelligent systems. Each new application system must be designed from scratch, employing sophisticated methods ranging from conventional signal processing to computational intelligence. Currently, a significant part of this overall algorithmic chain of the computational system model still has to be assembled manually by experienced designers in a time and labor consuming process. In this research work, this challenge is picked up and a methodology and algorithms for automated design of intelligent integrated and resource-aware multi-sensor systems employing multi-objective evolutionary computation are introduced. The proposed methodology tackles the challenge of rapid-prototyping of such systems under realization constraints and, additionally, includes features of system instance specific self-correction for sustained operation of a large volume and in a dynamically changing environment. The extension of these concepts to the reconfigurable hardware platform renders so called self-x sensor systems, which stands, e.g., for self-monitoring, -calibrating, -trimming, and -repairing/-healing systems. Selected experimental results prove the applicability and effectiveness of our proposed methodology and emerging tool. By our approach, competitive results were achieved with regard to classification accuracy, flexibility, and design speed under additional design constraints.

A nonaxial boost may reduce late complications of radiotherapy for prostate cancer

Energy Technology Data Exchange (ETDEWEB)

Ben-Josef, E; Mesina, C F; Choi, J; Forman, J D

1995-07-01

Purpose: The nonaxial external beam (NAEBT) prostate boost technique was designed to reduce late complications of radiotherapy for prostate cancer. It has been previously shown that with this beam arrangement, the volumes of bladder and rectum receiving high doses could be substantially reduced. This study was undertaken to find if these advantages in dose distribution would translate into clinically significant benefits. Materials and Methods: Follow-up was obtained on 106 prostate cancer patients who had been treated with 3D conformal radiotherapy. Late complications were scored using the RTOG scale. A standard four-field axial (STD) technique had been used to deliver 45 Gy to the prostate, seminal vesicles and periprostatic lymph-nodes. A subsequent 24 Gy boost had been delivered using a STD technique (58 patients) or a NAEBT technique (48 patients). In the latter, the opposing anterior and posterior pair of beams had been substituted for a right and left anterior infero-superior pair. Actuarial probabilities of developing late complications were calculated by the life-table method. The Mantel-Haenszel test was used to compare these probabilities between the two groups. Results: The groups were comparable in regard to age, race, pretreatment serum PSA, stage distribution and dose to prostate. With a median follow-up of 21 months, 18 patients have developed grade 1-2 gastrointestinal or genitourinary complications (14 in the STD group, 4 in the NAEBT group). There were no grade 3-4 complications. The actuarial 3-year complication probability was 58% and 11% in the STD and NAEBT groups, respectively. However, this difference was not statistically significant. Gastrointestinal and genitourinary complications were reduced from 12.1% to 6.2% and from 15.5% to 4.2%, respectively. Conclusion: The use of a nonaxial boost technique has resulted in fewer complications in patients treated with 3D conformal radiotherapy for localized prostate cancer. The greater reduction

Boosted Objects: A Probe of Beyond the Standard Model Physics

Energy Technology Data Exchange (ETDEWEB)

Abdesselam, A.; /Oxford U.; Kuutmann, E.Bergeaas; /DESY; Bitenc, U.; /Freiburg U.; Brooijmans, G.; /Columbia U.; Butterworth, J.; /University Coll. London; Bruckman de Renstrom, P.; /Cracow, INP; Buarque Franzosi, D.; /Turin U.; Buckingham, R.; /Oxford U.; Chapleau, B.; /McGill U.; Dasgupta, M.; /Manchester U.; Davison, A.; /University Coll. London; Dolen, J.; /UC, Davis; Ellis, S.; /Washington U., Seattle; Fassi, F.; /Lyon, IPN; Ferrando, J.; /Oxford U.; Frandsen, M.T.; /Oxford U.; Frost, J.; /Cambridge U.; Gadfort, T.; /Brookhaven; Glover, N.; /Durham U.; Haas, A.; /SLAC; Halkiadakis, E.; /Rutgers U., Piscataway /INFN, Milan Bicocca /Oxford U. /Ohio State U. /Rutherford /Oxford U. /Oxford U. /Maryland U. /Bristol U. /Princeton U. /Oxford U. /Oxford U. /Arizona U. /Johns Hopkins U. /Oxford U. /Fermilab /Rutherford /Bristol U. /Karlsruhe U., EKP /Weizmann Inst. /Washington U., Seattle /Johns Hopkins U. /Oslo U. /Durham U. /Princeton U. /Paris, LPTHE /CERN /Southern Denmark U., CP3-Origins /Granada U. /SLAC /Rutherford /Toronto U. /Stockholm U., OKC /Stockholm U. /Yale U.; /more authors..

2012-06-12

We present the report of the hadronic working group of the BOOST2010 workshop held at the University of Oxford in June 2010. The first part contains a review of the potential of hadronic decays of highly boosted particles as an aid for discovery at the LHC and a discussion of the status of tools developed to meet the challenge of reconstructing and isolating these topologies. In the second part, we present new results comparing the performance of jet grooming techniques and top tagging algorithms on a common set of benchmark channels. We also study the sensitivity of jet substructure observables to the uncertainties in Monte Carlo predictions.

Boosted objects: a probe of beyond the Standard Model physics

CERN Document Server

Abdesselam, A; Bitenc, U; Brooijmans, G; Butterworth, J; Bruckman de Renstrom, P; Buarque Franzosi, D; Buckingham, R; Chapleau, B; Dasgupta, M; Davison, A; Dolen, J; Ellis, S; Fassi, F; Ferrando, J; Frandsen, M T; Frost, J; Gadfort, T; Glover, N; Haas, A; Halkiadakis, E; Hamilton, K; Hays, C; Hill, C; Jackson, J; Issever, C; Karagoz, M; Katz, A; Kreczko, L; Krohn, D; Lewis, A; Livermore, S; Loch, P; Maksimovic, P; March-Russell, J; Martin, A; McCubbin, N; Newbold, D; Ott, J; Perez, G; Policchio, A; Rappoccio, S; Raklev, A R; Richardson, P; Salam, G P; Sannino, F; Santiago, J; Schwartzman, A; Shepherd-Themistocleous, C; Sinervo, P; Sjoelin, J; Son, M; Spannowsky, M; Strauss, E; Takeuchi, M; Tseng, J; Tweedie, B; Vermillion, C; Voigt, J; Vos, M; Wacker, J; Wagner-Kuhr, J; Wilson, M G

2011-01-01

We present the report of the hadronic working group of the BOOST2010 workshop held at the University of Oxford in June 2010. The first part contains a review of the potential of hadronic decays of highly boosted particles as an aid for discovery at the LHC and a discussion of the status of tools developed to meet the challenge of reconstructing and isolating these topologies. In the second part, we present new results comparing the performance of jet grooming techniques and top tagging algorithms on a common set of benchmark channels. We also study the sensitivity of jet substructure observables to the uncertainties in Monte Carlo predictions.

Dosimetric evaluation of simultaneous integrated boost during stereotactic body radiation therapy for pancreatic cancer

Energy Technology Data Exchange (ETDEWEB)

Yang, Wensha, E-mail: wensha.yang@cshs.org [Department of Radiation Oncology, Cedars Sinai Medical Center, Los Angeles, CA (United States); Reznik, Robert; Fraass, Benedick A. [Department of Radiation Oncology, Cedars Sinai Medical Center, Los Angeles, CA (United States); Nissen, Nicholas [Department of Surgery, Cedars Sinai Medical Center, Los Angeles, CA (United States); Hendifar, Andrew [Department of Gastrointestinal Oncology, Cedars Sinai Medical Center, Los Angeles, CA (United States); Wachsman, Ashley [Department of Cross-Sectional Imaging Interventional Oncology, Cedars Sinai Medical Center, Los Angeles, CA (United States); Sandler, Howard; Tuli, Richard [Department of Radiation Oncology, Cedars Sinai Medical Center, Los Angeles, CA (United States)

2015-04-01

Stereotactic body radiation therapy (SBRT) provides a promising way to treat locally advanced pancreatic cancer and borderline resectable pancreatic cancer. A simultaneous integrated boost (SIB) to the region of vessel abutment or encasement during SBRT has the potential to downstage otherwise likely positive surgical margins. Despite the potential benefit of using SIB-SBRT, the ability to boost is limited by the local geometry of the organs at risk (OARs), such as stomach, duodenum, and bowel (SDB), relative to tumor. In this study, we have retrospectively replanned 20 patients with 25 Gy prescribed to the planning target volume (PTV) and 33~80 Gy to the boost target volume (BTV) using an SIB technique for all patients. The number of plans and patients able to satisfy a set of clinically established constraints is analyzed. The ability to boost vessels (within the gross target volume [GTV]) is shown to correlate with the overlap volume (OLV), defined to be the overlap between the GTV + a 1(OLV1)- or 2(OLV2)-cm margin with the union of SDB. Integral dose, boost dose contrast (BDC), biologically effective BDC, tumor control probability for BTV, and normal tissue complication probabilities are used to analyze the dosimetric results. More than 65% of the cases can deliver a boost to 40 Gy while satisfying all OAR constraints. An OLV2 of 100 cm{sup 3} is identified as the cutoff volume: for cases with OLV2 larger than 100 cm{sup 3}, it is very unlikely the case could achieve 25 Gy to the PTV while successfully meeting all the OAR constraints.

Performance of Jet Substructure Techniques and Boosted Object Identification in ATLAS

CERN Document Server

Lacey, J; The ATLAS collaboration

2014-01-01

ATLAS has implemented and commissioned many new jet substructure techniques to aid in the identification and interpretation of hadronic final states originating from Lorentz-boosted heavy particles produced at the LHC. These techniques include quantum jets, jet charge, jet shapes, quark/gluon, boosted boson and top quark tagging, along with grooming methods such as pruning, trimming, and filtering. These techniques have been validated using the large 2012 ATLAS dataset. Presented here is a summary of the state of the art jet substructure and tagging techniques developed in ATLAS, their performance and recent results.

Shrinkage Degree in $L_{2}$ -Rescale Boosting for Regression.

Science.gov (United States)

Xu, Lin; Lin, Shaobo; Wang, Yao; Xu, Zongben

2017-08-01

L 2 -rescale boosting ( L 2 -RBoosting) is a variant of L 2 -Boosting, which can essentially improve the generalization performance of L 2 -Boosting. The key feature of L 2 -RBoosting lies in introducing a shrinkage degree to rescale the ensemble estimate in each iteration. Thus, the shrinkage degree determines the performance of L 2 -RBoosting. The aim of this paper is to develop a concrete analysis concerning how to determine the shrinkage degree in L 2 -RBoosting. We propose two feasible ways to select the shrinkage degree. The first one is to parameterize the shrinkage degree and the other one is to develop a data-driven approach. After rigorously analyzing the importance of the shrinkage degree in L 2 -RBoosting, we compare the pros and cons of the proposed methods. We find that although these approaches can reach the same learning rates, the structure of the final estimator of the parameterized approach is better, which sometimes yields a better generalization capability when the number of sample is finite. With this, we recommend to parameterize the shrinkage degree of L 2 -RBoosting. We also present an adaptive parameter-selection strategy for shrinkage degree and verify its feasibility through both theoretical analysis and numerical verification. The obtained results enhance the understanding of L 2 -RBoosting and give guidance on how to use it for regression tasks.

Design and transient analyses of passive emergency feedwater system of CPR1000. Part 1. Air cooling condition

International Nuclear Information System (INIS)

Zhang Yapei; Qiu Suizheng; Su Guanghui; Tian Wenxi; Cao Jianhua; Lu Donghua; Fu Xiangang

2011-01-01

The steam generator secondary passive emergency feedwater system is a new design for traditional generation Ⅱ + reactor CPR1000. The passive emergency feedwater system is designed to supply water to the SG shell side and improve the safety and reliability of CPR1000 by completely or partially replacing traditional emergency water cooling system in the event of the feed line break (FLB) or loss of heat sink accident. The passive emergency feedwater system consists of steam generator (SG), heat exchanger (HX), air cooling tower, emergency makeup tank (EMT), and corresponding pipes and valves for air cooling condition. In order to improve the safety and reliability of CPR1000, the model of the primary loop system and the passive emergency feedwater system was developed to investigate residual heat removal capability of the passive emergency feedwater system and the transient characteristics of the primary loop system affected by the passive emergency feedwater system using RELAP5/MOD3.4. The transient characteristics of the primary loop system and the passive emergency feedwater system were calculated in the event of feed line break accident. Sensitivity studies of the passive emergency feedwater system were also conducted to investigate the response of the primary loop and the passive emergency feedwater system on the main parameters of the passive emergency feedwater system. The passive emergency feedwater system could supply water to the SG shell side from the EMT successfully. The calculation results showed that the passive emergency feedwater system could take away the decay heat from the primary loop effectively for air cooling condition, and that the single-phase and two-phase natural circulations were established in the primary loop and passive emergency feedwater system loop, respectively. (author)

The Attentional Boost Effect and Context Memory

Science.gov (United States)

Mulligan, Neil W.; Smith, S. Adam; Spataro, Pietro

2016-01-01

Stimuli co-occurring with targets in a detection task are better remembered than stimuli co-occurring with distractors--the attentional boost effect (ABE). The ABE is of interest because it is an exception to the usual finding that divided attention during encoding impairs memory. The effect has been demonstrated in tests of item memory but it is…

Design and Simulation to Composite PI Controller on the Stratospheric Airship

Directory of Open Access Journals (Sweden)

Kangwen Sun

2014-05-01

Full Text Available In view of the stratospheric airship application requirements on energy storage and management system, based on the topology of DC/DC converter main circuit, the composite PI controller is designed to realize respective control with the Boost mode and Buck mode. Furthermore, limit stop integration method is proposed to achieve a buck-boost complex DC/DC converter boost with effective switching buck. Then, with the MATLAB Control System Toolbox design model, the composite PI controller design and a simulation is accomplished. According to the simulation model, the structure and parameters of the controller to the system can be easily adjusted. Finally, by using the average large-signal switching mathematical model to create sub-circuit in place of the actual circuit model, the whole circuit model of the DC/DC converter is constructed with MATLAB, and then, from the analysis of simulation results, it’s proved that the method can shorten the simulation time and obtain better convergence of the target.

Simple grain mill boosts production and eases women's workload ...

International Development Research Centre (IDRC) Digital Library (Canada)

... grain mill boosts production and eases women's workload. 11 janvier 2013. Image ... It aims to increase the production, improve the processing, develop new ... farmer societies, women's self-help groups, and the food-processing industry.

7th International Workshop on Boosted Object Phenomenology, Reconstruction and Searches in HEP

CERN Document Server

2015-01-01

BOOST2015 is the seventh of a series of successful joint theory/experiment workshops which bring together the world leading experts from theory and the Tevatron and LHC experiments to discuss the latest progress and develop new approaches on the reconstruction and use of boosted decay topologies as search tools for new physics. This year, the workshop is hosted by the University of Chicago.

Cross-Regulation Assessment of DIDO Buck-Boost Converter for Renewable Energy Application

Directory of Open Access Journals (Sweden)

Deepak Elamalayil Soman

2017-06-01

Full Text Available When medium- or high-voltage power conversion is preferred for renewable energy sources, multilevel power converters have received much of the interest in this area as methods for enhancing the conversion efficiency and cost effectiveness. In such cases, multilevel, multi-input multi-output (MIMO configurations of DC-DC converters come to the scenario for integrating several sources together, especially considering the stringent regulatory needs and the requirement of multistage power conversion systems. Considering the above facts, a three-level dual input dual output (DIDO buck-boost converter, as the simplest form of MIMO converter, is proposed in this paper for DC-link voltage regulation. The capability of this converter for cross regulating the DC-link voltage is analyzed in detail to support a three-level neutral point clamped inverter-based grid connection in the future. The cross-regulation capability is examined under a new type of pulse delay control (PDC strategy and later compared with a three-level boost converter (TLBC. Compared to conventional boost converters, the high-voltage three-level buck boost converter (TLBBC with PDC exhibits a wide controllability range and cross regulation capability. These enhanced features are extremely important for better regulating variable output renewable energy sources such as solar, wind, wave, marine current, etc. The simulation and experimental results are provided to validate the claim.

A Battery Power Bank with Series-Connected Buck–Boost-Type Battery Power Modules

Directory of Open Access Journals (Sweden)

Tsung-Hsi Wu

2017-05-01

Full Text Available The operation of a battery power bank with series-connected buck–boost-type battery power modules (BPMs was investigated in this study. Each BPM consisted of a battery pack with an associated buck–boost converter for individually controlling battery currents. With a proposed discharging scenario, load voltage regulation with charge equalization among batteries was performed by controlling the battery currents in accordance with their state-of-charges (SOCs estimated by real-time battery-loaded voltages detected under the same operating condition. In addition, the fault tolerance was executed to isolate exhausted or faulty batteries from the battery power bank without interrupting the system operation. Experiments were conducted to verify the effectiveness of the discharging scenario for a laboratory battery power bank with four series buck–boost BPMs.

Starting Up in a Down Market, with a Boost From Entrepreneurship Graduate Programs

Science.gov (United States)

Taylor, Cyrus

2003-03-01

In the late 1990's, it seemed that any two graduate students and their dog could start and grow a high-tech company. With the collapse of, first, the internet sector, and, more recently, the telecommunications sector, there has been a traumatic shake-out among high tech firms, and the challenges facing new firms appear to have greatly increased. This talk will highlight the keys for physics entrepreneurs to survive and even thrive in this environment, with a special initial boost from new graduate programs combining business school and physics training. The infrastructure needed by educational programs designed to empower physicists as entrepreneurs is discussed.

SU-E-T-210: Comparison of Proton with Electron Boost in Breast Cancer Treatment

Energy Technology Data Exchange (ETDEWEB)

Zheng, Y; Chang, A [Procure Proton Therapy Center, Oklahoma City, OK (United States); Liu, Y [INTEGRIS Cancer Institute of Oklahoma, Oklahoma City, OK (United States)

2015-06-15

Purpose: Electron beams are commonly used for boost radiation following whole breast irradiation (WBI) to improve the in-breast local control. Proton beams have a finite range and a sharper distal dose falloff compared to electron beams, thus potentially sparing more heart and lung in breast treatment. The purpose of the study is to compare protons with electrons for boost breast treatment in terms of target coverage and normal tissue sparing. Methods: Six breast cancer patients were included in this study. All women received WBI to 45–50 Gy, followed by a 10–16.2 Gy boost with standard fractionation. If proton beams were used for the boost treatment, an electron plan was retrospectively generated for comparison using the same CT set and structures, and vice versa if electron beams were used for treatment. Proton plans were generated using the treatment planning system (TPS) with two to three uniform scanning proton beams. Electron plans were generated using the Pinnacle TPS with one single en face beam. Dose-volume histograms (DVH) were calculated and compared between proton and electron boost plans. Results: Proton plans show a similar boost target coverage, similar skin dose, and much better heart and lung sparing. For an example patient, V95% for PTV was 99.98% and skin (5 mm shell) received a max dose close to the prescription dose for both protons and electrons; however, V2 and V5 for the ipsilateral lung and heart were 37.5%, 17.9% and 19.9%, 4.9% respectively for electrons, but were essentially 0 for protons. Conclusions: This dosimetric comparison demonstrates that while both proton therapy and electron therapy provided similar coverage and skin dose, proton therapy could largely reduce the dose to lung and heart, thus leading to potential less side effects.

Reduction in Radiation-Induced Morbidity by Use of an Intercurrent Boost in the Management of Early-Stage Breast Cancer

International Nuclear Information System (INIS)

Trombetta, Mark; Julian, Thomas B.; Valakh, Vladimir; Greenberg, Larisa; Labban, George; Khalid, Mian K.; Werts, E. Day; Parda, David

2010-01-01

Purpose: Electron or photon boost immediately following whole-breast irradiation performed after conservation surgery for early-stage breast cancer is the accepted standard of care. This regimen frequently results in Grade III dermatitis, causing discomfort or treatment interruption. Herein, we compare patients treated with whole-breast irradiation followed by boost compared with a cohort with a planned intercurrent radiation boost. Methods and Materials: The records of 650 consecutive breast cancer patients treated at Allegheny General Hospital (AGH) between 2000 and 2008 were reviewed. Selected for this study were 327 patients with T1 or T2 tumors treated with external beam radiotherapy postlumpectomy. One hundred and sixty-nine patients were treated by whole-breast radiotherapy (WBRT) followed by boost at completion. One hundred fifty-eight were treated with a planned intercurrent boost (delivered following 3,600 cGy WBRT). The mean whole breast radiation dose in the conventionally treated group was 5,032 cGy (range, 4500-5400 cGy), and the mean whole breast dose was 5,097 cGy (range, 4860-5040 cGy) in the group treated with a planned intercurrent boost. Results: The occurrence of Grade III dermatitis was significantly reduced in the WBRT/intercurrent boost group compared with the WBRT/boost group (0.6% vs. 8.9%), as was the incidence of treatment interruption (1.9% vs. 14.2%). With a median follow-up of 32 months and 27 months, respectively, no significant difference in local control was identified. Conclusions: Patients treated with intercurrent boost developed less Grade III dermatitis and unplanned treatment interruptions with similar local control.

BioBoost. Biomass based energy intermediates boosting bio-fuel production

Energy Technology Data Exchange (ETDEWEB)

Niebel, Andreas [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany). Institut fuer Katalyseforschung und -technologie (IKFT)

2013-10-01

To increase the share of biomass for renewable energy in Europe conversion pathways which are economic, flexible in feedstock and energy efficient are needed. The BioBoost project concentrates on dry and wet residual biomass and wastes as feedstock for de-central conversion by fast pyrolysis, catalytic pyrolysis and hydrothermal carbonization to the intermediate energy carriers oil, coal or slurry. Based on straw the energy density increases from 2 to 20-30 GJ/m{sup 3}, enabling central GW scale gasification plants for bio-fuel production. A logistic model for feedstock supply and connection of de-central with central conversion is set up and validated allowing the determination of costs, the number and location of de-central and central sites. Techno/economic and environmental assessment of the value chain supports the optimization of products and processes. The utilization of energy carriers is investigated in existing and coming applications of heat and power production and synthetic fuels and chemicals. (orig.)

Modelling and Control Design of a Dual Buck-Boost AC/DC Converter Used in the DC Nano-Grid

DEFF Research Database (Denmark)

Wu, Weimin; Liu, Yuan; Wang, Houqing

2016-01-01

Due to widely used DC characterized loads and more distributed power generation sources, the DC Nano-grid becomes more and more popular and seen as an alternative to the AC-grid in future. For the safety considerations, the DC Nano-grid should provide reliable grounding for the residential loads...... like the low voltage AC power system. In this paper, a dual Buck-Boost AC/DC converter for use in the united grounding configuration based DC Nano-grid with three terminal outputs is proposed. It will be much easy to construct an efficient DC Nano-grid based on the existing low AC power system by using...

CMOS single-stage input-powered bridge rectifier with boost switch and duty cycle control

Science.gov (United States)

Radzuan, Roskhatijah; Mohd Salleh, Mohd Khairul; Hamzah, Mustafar Kamal; Ab Wahab, Norfishah

2017-06-01

This paper presents a single-stage input-powered bridge rectifier with boost switch for wireless-powered devices such as biomedical implants and wireless sensor nodes. Realised using CMOS process technology, it employs a duty cycle switch control to achieve high output voltage using boost technique, leading to a high output power conversion. It has only six external connections with the boost inductance. The input frequency of the bridge rectifier is set at 50 Hz, while the switching frequency is 100 kHz. The proposed circuit is fabricated on a single 0.18-micron CMOS die with a space area of 0.024 mm2. The simulated and measured results show good agreement.

Soft switching PWM isolated boost converter for fuel cell application

Energy Technology Data Exchange (ETDEWEB)

Rezaei, M.; Adib, E. [Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of)

2009-07-01

This presentation introduced a newly developed soft switching, isolated boost type converter for fuel cell applications. With a simple PWM control circuit, the converter achieves zero voltage switching the main switch. Since the auxiliary circuit is soft switched, the converter can operate at high powers which make it suitable for fuel cell applications. In particular, the converter is suitable for the interface of fuel cell and inverters because of its high voltage gain and isolation between input and output sources. In addition, the input current of the converter (current drained from the fuel cell) is almost constant since it is a boost type converter. The converter was analyzed and the simulation results validate the theoretical analysis.

A comparison between Miller and five-stroke cycles for enabling deeply downsized, highly boosted, spark-ignition engines with ultra expansion

International Nuclear Information System (INIS)

Li, Tie; Wang, Bin; Zheng, Bin

2016-01-01

Highlights: • Deeply downsized, highly boosted SI engine with ultra-expansion cycle is studied. • The Miller and five stroke cycles are compared on BSFC improvements and WOT performance. • The mechanism of fuel conversion efficiency improvement at various loads is discussed. • Performance of the two-stage boosting system for the downsized SI engine is investigated. • A unique strategy using the bypass for the five-stroke engine is proposed. - Abstract: It has been well known that the engine downsizing combined with intake boosting is an effective way to improve the fuel conversion efficiency without penalizing the engine torque performance. However, the potential of engine downsizing is not yet fully explored, and the major hurdles include the knocking combustion and the pre-turbine temperature limit, owing to the aggressive intake boosting. Using the engine cycle simulation, this paper compares the effects of the Miller and five stroke cycles on the performance of the deeply downsized and highly boosted SI engine, taking the engine knock and pre-turbine temperature into consideration. In the simulation, the downsizing is implemented by reducing the combustion cylinder number from four to two, while a two stage boosting system is designed for the deeply downsized engine to ensure the wide-open-throttle (WOT) performance comparable to the original four cylinder engine. The Miller cycle is realized by varying the intake valve timing and lift, while the five stroke cycle is enabled with addition of an extra expansion cylinder between the two combustion cylinders. After calibration and validation of the engine cycle simulation models using the experimental data in the original engine, the performances of the deeply downsized engines with both the Miller and five stroke cycles are numerically studied. For the most frequently operated points on the torque-speed map, at low loads the Miller cycle exhibits superior performance over the five-stroke cycle in terms

The emergence of new organization designs. Evidences from self-managed team-based organizations

NARCIS (Netherlands)

Annosi, Maria Carmela; Giustiniano, Luca; Brunetta, Federica; Magnusson, Mats

2017-01-01

New organization designs emerge continuously in highly dynamic innovation context to improve readiness to change. The adoption of self-managing teams operating cross-functionally on a bulk of products, together with the reduction of vertical layers in the organization, seems to be a common strategy

"Not for human consumption": a review of emerging designer drugs.

Science.gov (United States)

Musselman, Megan E; Hampton, Jeremy P

2014-07-01

Synthetic, or "designer" drugs, are created by manipulating the chemical structures of other psychoactive drugs so that the resulting product is structurally similar but not identical to illegal psychoactive drugs. Originally developed in the 1960s as a way to evade existing drug laws, the use of designer drugs has increased dramatically over the past few years. These drugs are deceptively packaged as "research chemicals," "incense," "bath salts," or "plant food," among other names, with labels that may contain warnings such as "not for human consumption" or "not for sale to minors." The clinical effects of most new designer drugs can be described as either hallucinogenic, stimulant, or opioid-like. They may also have a combination of these effects due to designer side-chain substitutions. The easy accessibility and rapid emergence of new designer drugs have created challenges for health care providers when treating patients presenting with acute toxicity from these substances, many of which can produce significant and/or life-threatening adverse effects. Moreover, the health care provider has no way to verify the contents and/or potency of the agent ingested because it can vary between packages and distributors. Therefore, a thorough knowledge of the available designer drugs, common signs and symptoms of toxicity associated with these agents, and potential effective treatment modalities are essential to appropriately manage these patients. © 2014 Pharmacotherapy Publications, Inc.

Child abuse inventory at emergency rooms: CHAIN-ER rationale and design

Directory of Open Access Journals (Sweden)

Nieuwenhuis Edward ES

2011-10-01

Full Text Available Abstract Background Child abuse and neglect is an important international health problem with unacceptable levels of morbidity and mortality. Although maltreatment as a cause of injury is estimated to be only 1% or less of the injured children attending the emergency room, the consequences of both missed child abuse cases and wrong suspicions are substantial. Therefore, the accuracy of ongoing detection at emergency rooms by health care professionals is highly important. Internationally, several diagnostic instruments or strategies for child abuse detection are used at emergency rooms, but their diagnostic value is still unknown. The aim of the study 'Child Abuse Inventory at Emergency Rooms' (CHAIN-ER is to assess if active structured inquiry by emergency room staff can accurately detect physical maltreatment in children presenting at emergency rooms with physical injury. Methods/design CHAIN-ER is a multi-centre, cross-sectional study with 6 months diagnostic follow-up. Five thousand children aged 0-7 presenting with injury at an emergency room will be included. The index test - the SPUTOVAMO-R questionnaire- is to be tested for its diagnostic value against the decision of an expert panel. All SPUTOVAMO-R positives and a 15% random sample of the SPUTOVAMO-R negatives will undergo the same systematic diagnostic work up, which consists of an adequate history being taken by a pediatrician, inquiry with other health care providers by structured questionnaires in order to obtain child abuse predictors, and by additional follow-up information. Eventually, an expert panel (reference test determines the true presence or absence of child abuse. Discussion CHAIN-ER will determine both positive and negative predictive value of a child abuse detection instrument used in the emergency room. We mention a benefit of the use of an expert panel and of the use of complete data. Conducting a diagnostic accuracy study on a child abuse detection instrument is also

Circuit Simulation for Solar Power Maximum Power Point Tracking with Different Buck-Boost Converter Topologies

Directory of Open Access Journals (Sweden)

Jaw-Kuen Shiau

2014-08-01

Full Text Available The power converter is one of the essential elements for effective use of renewable power sources. This paper focuses on the development of a circuit simulation model for maximum power point tracking (MPPT evaluation of solar power that involves using different buck-boost power converter topologies; including SEPIC, Zeta, and four-switch type buck-boost DC/DC converters. The circuit simulation model mainly includes three subsystems: a PV model; a buck-boost converter-based MPPT system; and a fuzzy logic MPPT controller. Dynamic analyses of the current-fed buck-boost converter systems are conducted and results are presented in the paper. The maximum power point tracking function is achieved through appropriate control of the power switches of the power converter. A fuzzy logic controller is developed to perform the MPPT function for obtaining maximum power from the PV panel. The MATLAB-based Simulink piecewise linear electric circuit simulation tool is used to verify the complete circuit simulation model.

Boosted Higgs shapes

International Nuclear Information System (INIS)

Schlaffer, Matthias; Spannowsky, Michael; Wymant, Chris

2014-05-01

The inclusive Higgs production rate through gluon fusion has been measured to be in agreement with the Standard Model (SM). We show that even if the inclusive Higgs production rate is very SM-like, a precise determination of the boosted Higgs transverse momentum shape offers the opportunity to see effects of natural new physics. These measurements are generically motivated by effective field theory arguments and specifically in extensions of the SM with a natural weak scale, like composite Higgs models and natural supersymmetry. We show in detail how a measurement at high transverse momentum of H→2l+p T via H→ττ and H→WW * could be performed and demonstrate that it offers a compelling alternative to the t anti tH channel. We discuss the sensitivity to new physics in the most challenging scenario of an exactly SM-like inclusive Higgs cross-section.

HIV-1-Specific Antibody Response and Function after DNA Prime and Recombinant Adenovirus 5 Boost HIV Vaccine in HIV-Infected Subjects.

Directory of Open Access Journals (Sweden)

Johannes S Gach

Full Text Available Little is known about the humoral immune response against DNA prime-recombinant adenovirus 5 (rAd5 boost HIV vaccine among HIV-infected patients on long-term suppressive antiretroviral therapy (ART. Previous studies emphasized cellular immune responses; however, current research suggests both cellular and humoral responses are likely required for a successful therapeutic vaccine. Thus, we aimed to understand antibody response and function induced by vaccination of ART-treated HIV-1-infected patients with immune recovery. All subjects participated in EraMune 02, an open-label randomized clinical trial of ART intensification followed by a six plasmid DNA prime (envA, envB, envC, gagB, polB, nefB and rAd5 boost HIV vaccine with matching inserts. Antibody binding levels were determined with a recently developed microarray approach. We also analyzed neutralization efficiency and antibody-dependent cellular cytotoxicity (ADCC. We found that the DNA prime-rAd5 boost vaccine induced a significant cross-clade HIV-specific antibody response, which correlated with antibody neutralization efficiency. However, despite the increase in antibody binding levels, the vaccine did not significantly stimulate neutralization or ADCC responses. This finding was also reflected by a lack of change in total CD4+ cell associated HIV DNA in those who received the vaccine. Our results have important implications for further therapeutic vaccine design and administration, especially in HIV-1 infected patients, as boosting of preexisting antibody responses are unlikely to lead to clearance of latent proviruses in the HIV reservoir.

Biochar boosts tropical but not temperate crop yields

NARCIS (Netherlands)

Jeffery, Simon; Abalos Rodriguez, Diego; Prodana, Marija; Bastos, Ana Catarina; Groenigen, van Jan Willem; Hungate, Bruce A.; Verheijen, Frank

2017-01-01

Applying biochar to soil is thought to have multiple benefits, from helping mitigate climate change [1, 2], to managing waste [3] to conserving soil [4]. Biochar is also widely assumed to boost crop yield [5, 6], but there is controversy regarding the extent and cause of any yield benefit [7].

Curriculum Design and Implementation of the Emergency Medicine Chief Resident Incubator.

Science.gov (United States)

Gisondi, Michael A; Chou, Adaira; Joshi, Nikita; Sheehy, Margaret K; Zaver, Fareen; Chan, Teresa M; Riddell, Jeffrey; Sifford, Derek P; Lin, Michelle

2018-02-24

Background Chief residents receive minimal formal training in preparation for their administrative responsibilities. There is a lack of professional development programs specifically designed for chief residents. Objective In 2015, Academic Life in Emergency Medicine designed and implemented an annual, year-long, training program and virtual community of practice for chief residents in emergency medicine (EM). This study describes the curriculum design process and reports measures of learner engagement during the first two cycles of the curriculum. Methods Kern's Six-Step Approach for curriculum development informed key decisions in the design and implementation of the Chief Resident Incubator. The resultant curriculum was created using constructivist social learning theory, with specific objectives that emphasized the needs for a virtual community of practice, longitudinal content delivery, mentorship for participants, and the facilitation of multicenter digital scholarship. The 12-month curriculum included 11 key administrative or professional development domains, delivered using a combination of digital communications platforms. Primary outcomes measures included markers of learner engagement with the online curriculum, recognized as modified Kirkpatrick Level One outcomes for digital learning. Results An average of 206 chief residents annually enrolled in the first two years of the curriculum, with an overall participation by 33% (75/227) of the allopathic EM residency programs in the United States (U.S.). There was a high level of learner engagement, with an average 13,414 messages posted per year. There were also 42 small group teaching sessions held online, which included 39 faculty and 149 chief residents. The monthly e-newsletter had a 50.7% open rate. Digital scholarship totaled 23 online publications in two years, with 67 chief resident co-authors and 21 faculty co-authors. Conclusions The Chief Resident Incubator is a virtual community of practice that

Cortisol boosts risky decision-making behavior in men but not in women.

Science.gov (United States)

Kluen, Lisa Marieke; Agorastos, Agorastos; Wiedemann, Klaus; Schwabe, Lars

2017-10-01

Acute stress may escalate risky decision-making in men, while there is no such effect in women. Although first evidence links these gender-specific effects of stress to stress-induced changes in cortisol, whether elevated cortisol is indeed sufficient to boost risk-taking, whether a potential cortisol effect depends on simultaneous noradrenergic activation, and whether cortisol and noradrenergic activation exert distinct effects on risk-taking in men and women is unknown. In this experiment, we therefore set out to elucidate the impact of cortisol and noradrenergic stimulation on risky decision-making in men and women. In a fully-crossed, placebo-controlled, double-blind design, male and female participants received orally either a placebo, hydrocortisone, yohimbine, an alpha-2-adrenoceptor-antagonist leading to increased noradrenergic stimulation, or both drugs before completing the balloon analogue risk task, a validated measure of risk-taking. Overall, participants' choice was risk-sensitive as reflected in reduced responding in high- compared to moderate- and low-risk conditions. Cortisol, however, led to a striking increase in risk-taking in men, whereas it had no effect on risk-taking behavior in women. Yohimbine had no such effect and the gender-specific effect of cortisol was not modulated by yohimbine. Our data show that cortisol boosts risk-taking behavior in men but not in women. This differential effect of cortisol on risk-taking may drive gender differences in risky decision-making under stress. Copyright © 2017 Elsevier Ltd. All rights reserved.

Endoscope-guided interstitial intensity-modulated brachytherapy and intracavitary brachytherapy as boost radiation for primary early T stage nasopharyngeal carcinoma.

Directory of Open Access Journals (Sweden)

Xiang-Bo Wan

Full Text Available BACKGROUND: Intracavitary brachytherapy (ICBT is usually applied as boost radiotherapy for superficial residual of nasopharyngeal carcinoma (NPC after primary extern-beam radiptherapy (ERT. Here, we evaluated the outcome of endoscope-guided interstitial intensity-modulated brachytherapy (IMBT boost radiation for deep-seated residual NPC. METHODOLOGY/PRINCIPAL FINDINGS: Two hundred and thirteen patients with residual NPC who were salvaged with brachytherapy boost radiation during 2005-2009 were analyzed retrospectively. Among these patients, 171 patients had superficial residual NPC (≤1 cm below the nasopharyngeal epithelium were treated with ICBT boost radiation, and interstitial IMBT boost radiation was delivered to 42 patients with deep-seated residual NPC (>1 cm below the nasopharyngeal epithelium. We found that IMBT boost subgroup had a higher ratio of T2b (81.0% VS 34.5%, P<0.001 and stage II (90.5% VS 61.4%, P = 0.001 than that of ICBT boost subgroup. The dosage of external-beam radiotherapy in the nasopharyngeal (63.0±3.8 VS 62.6±4.3 Gray (Gy, P = 0.67 and regional lymph nodes (55.8±5.0 VS 57.5±5.7 Gy, P = 0.11 was comparable in both groups. For brachytherapy, IMBT subgroup had a lower boost radiation dosage than ICBT subgroup (11.0±2.9 VS 14.8±3.2 Gy, P<0.01. Though the IMBT group had deeper residual tumors and received lower boost radiation dosages, both subgroups had the similar 5-year actuarial overall survival rate (IMBT VS ICBT group: 96.8% VS 93.6%, P = 0.87, progression-free survival rate (92.4% VS 86.5%, P = 0.41 and distant metastasis-free survival rate (94.9% VS 92.7%, P = 0.64. Moreover, IMBT boost radiation subgroup had a similar local (97.4% VS 94.4%, P = 0.57 and regional (95.0% VS 97.2%, P = 0.34 control to ICBT subgroup. The acute and late toxicities rates were comparable between the both subgroups. CONCLUSIONS/SIGNIFICANCE: IMBT boost radiation may be a promising therapeutic

Non Isolated and Non-Inverting Cockcroft Walton Multiplier Based Hybrid 2Nx Interleaved Boost Converter For Renewable Energy Applications

DEFF Research Database (Denmark)

Bhaskar, Mahajan Sagar; Padamanaban, Sanjeevi Kumar; Blaabjerg, Frede

2016-01-01

In this paper hybrid non isolated and non-invertingCockcroft-Walton multiplier based 2Nx InterleavedBoost converter (2Nx IBC) for renewable energy applications is presented. The presented hybrid boost converter topology is derived from non-inverting Nx Multilevel Boost Converter (Nx MBC......) and inverting Nx Multilevel Boost Converter (Nx MBC). In renewable energy applications, generated voltage needs to be stepped up with high conversion ratio using a DC-DC converter at voltage levels as per the application requirement. The advantages of the presentedtopology of interleaved converter are high...

Effective local control of vertebral metastases by simultaneous integrated boost radiotherapy. Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Lubgan, Dorota; Ziegaus, Anke; Semrau, Sabine; Lambrecht, Ulrike; Lettmaier, Sebastian; Fietkau, Rainer [Erlangen University Hospital, Department of Radiation Oncology, Erlangen (Germany)

2014-11-14

The primary endpoint was to improve local tumour control of patients with metastatic spinal tumours by stereotactic body radiotherapy (SBRT) and dose escalation by simultaneous, integrated boost (PTV-boost). We used a whole vertebral body (PTV-elective) contouring approach. Secondary endpoints were severity of acute and chronic adverse effects and overall survival. In all, 33 patients with metastases of the vertebral column were treated at Erlangen University Hospital. SBRT was given in 12 or 10 fractions. The metastatic lesion (PTV-boost) received 3.6 Gy (range 3.0-4.51 Gy) per fraction for a total of 42.0 Gy (24.36-48.0 Gy) and the whole vertebra (PTV-elective) received 2.85 Gy (range 1.8-3.6 Gy) per fraction for a total of 32.39 Gy (range 21.60-38.0 Gy). Patients were followed up every 3 months. Local control rate of all patients was 93 % at 12 and 24 months. The overall survival rate was 54 % at 12 months, 38 % at 24 months and 18 % at 36 months. No radiation myelopathy occurred. The most frequently observed adverse events in 3 cases was oesophagitis grade 2. SBRT with simultaneous, integrated boost was associated with excellent local control of 93 % after 24 months. This result shows the possibility of delivering escalated doses to the target while still keeping the incidence of side effects low. This study forms the basis for a future randomised controlled trial comparing conventional radiotherapy (10 fractions of 3 Gy) with hypofractionated dose intensified SBRT (12 fractions of 3 Gy + integrated boost 12 fractions of 4 Gy) for improvement of local tumour control and pain. (orig.) [German] Das primaere Ziel der Studie war die Verbesserung der lokalen Tumorkontrolle von Patienten mit Wirbelkoerpermetastasen mittels stereotaktischer Radiotherapie (SBRT) mit Dosiseskalation durch einen simultan integrierten Boost (PTV-Boost). Dabei wurde der ganze Wirbelkoerper konturiert (PTV-Elektive). Zu den sekundaeren Endpunkten der Studie gehoerten der Schweregrad von

Modeling and Simulation of PMSG Wind Turbine with Boost Converter Working under Discontinuous Conduction Mode

DEFF Research Database (Denmark)

Qin, Nan; Xu, Zhao

2008-01-01

in the discontinuous conducting mode (DCM). The new wind turbine model with the variable speed control of the PMSG based on duty cycle control of the boost converter has been developed in Matlab Simulink. Simulation studies show that DCM working mode of the boost converter provides more flexibility in controlling...

Adaptive Kernel in Meshsize Boosting Algorithm in KDE ...

African Journals Online (AJOL)

This paper proposes the use of adaptive kernel in a meshsize boosting algorithm in kernel density estimation. The algorithm is a bias reduction scheme like other existing schemes but uses adaptive kernel instead of the regular fixed kernels. An empirical study for this scheme is conducted and the findings are comparatively ...

Fixed switching frequency applied in single-phase boost AC to DC converter

International Nuclear Information System (INIS)

Chen, T.-C.; Ren, T.-J.; Ou, J.-C.

2009-01-01

The fixed switching frequency control for a single-phase boost AC to DC converter to achieve a sinusoidal line current and unity power factor is proposed in this paper. The relation between the line current error and the fixed switching frequency was developed. For a limit line current error, the minimum switching frequency for a boost AC to DC converter can be achieved. The proposed scheme was implemented using a 32-bit digital signal processor TMS320C32. Simulations and experimental results demonstrate the feasibility and fast dynamic response of the proposed control strategy.

Role of Brachytherapy in the Boost Management of Anal Carcinoma With Node Involvement (CORS-03 Study)

Energy Technology Data Exchange (ETDEWEB)

Moureau-Zabotto, Laurence, E-mail: moureaul@ipc.unicancer.fr [Department of Radiation Therapy, Institut Paoli Calmettes, Marseille (France); Ortholan, Cecile [Department of Radiation Therapy, Monaco (France); Hannoun-Levi, Jean-Michel [Department of Radiation Therapy, Antoine Lacassagne Cancer Center, Nice (France); Teissier, Eric [Azurean Cancer Center, Mougins (France); Cowen, Didier [Department of Radiation Therapy, Timone Academic Hospital and North Academic Hospital, Marseille (France); Department of Radiation Therapy, Val d' Aurelle Cancer Center, Montpellier (France); Salem, Nagi [Department of Radiation Therapy, Institut Paoli Calmettes, Marseille (France); Lemanski, Claire [Catalan Oncology Center, Perpignan (France); Ellis, Steve [French Red Cross Center, Toulon (France); Resbeut, Michel [Department of Radiation Therapy, Institut Paoli Calmettes, Marseille (France); French Red Cross Center, Toulon (France)

2013-03-01

Purpose: To assess retrospectively the clinical outcome in anal cancer patients, with lymph node involvement, treated with split-course radiation therapy and receiving a boost through external beam radiation therapy (EBRT) or brachytherapy (BCT). Methods and Materials: From 2000 to 2005, among 229 patients with invasive nonmetastatic anal squamous cell carcinoma, a selected group of 99 patients, with lymph node involvement, was studied. Tumor staging reported was T1 in 4 patients, T2 in 16 patients, T3 in 49 patients, T4 in 16 patients, and T unknown in 14 patients and as N1 in 67 patients and N2/N3 in 32 patients. Patients underwent a first course of EBRT (mean dose, 45.1 Gy) followed by a boost (mean dose, 18 Gy) using EBRT (50 patients) or BCT (49 patients). All characteristics of patients and tumors were well balanced between the BCT and EBRT groups. Prognostic factors of cumulative rate of local recurrence (CRLR), cumulative rate of distant (including nodal) recurrence (CRDR), colostomy-free survival (CFS) rate, and overall survival (OS) rate were analyzed for the overall population and according to the nodal status classification. Results: The median follow-up was 71.5 months. The 5-year CRLR, CRDR, CFS rate, and OS rate were 21%, 19%, 63%, and 74.4%, respectively. In the overall population, the type of node involvement (N1 vs N2/N3) was the unique independent prognostic factor for CRLR. In N1 patients, by use of multivariate analysis, BCT boost was the unique prognostic factor for CRLR (4% for BCT vs 31% for EBRT; hazard ratio, 0.08; P=.042). No studied factors were significantly associated with CRDR, CFS, and OS. No difference with regard to boost technique and any other factor studied was observed in N2/N3 patients for any kind of recurrence. Conclusion: In anal cancer, even in the case of initial perirectal node invasion, BCT boost is superior to EBRT boost for CRLR, without an influence on OS, suggesting that N1 status should not be a contraindication to

Capable design or designing capabilities? An exploration of service design as an emerging organizational capability in Telenor – Martinkenaite

Directory of Open Access Journals (Sweden)

Ieva Martinkenaite

2017-01-01

Full Text Available This empirical paper examines a process, starting with the managerial decision to make service design an organizational capability, and follows it as it unfolds over time within one organization. Service design has become an established business practice of how firms create new products and services to promote differentiation in an increasingly uncertain business landscape. Implicit in the literature on service design are assumptions about strategic implications of adopting the prescribed innovation methods and tools. However, little is known about how service design evolves into an organizational capability enabling firms to transform their existing businesses and sustain competitiveness. Through a longitudinal, exploratory case study of service design practices in one of the world’s largest telecommunications companies, we explicate mechanisms through which service design evolves into an organizational capability by exploring the research question: what are the mechanisms through which service design develops into an organizational capability? Our study reveals the effect of an initial introduction of service design tools, identification of boundaryspanning actors and co-alignment of dedicated resources between internal functions, as well as through co-creation with customers. Over time, these activities lead to the adoption of service design practices, and subsequently these practices spark incremental learning throughout the organization, alter managerial decisions and influence multiple paths for the development of new capabilities. Reporting on this process, we are able to describe how service design practices were disseminated and institutionalized within the organization we observed. This study thus contributes by informing how service design can evolve into an organizational capability, as well as by bridging the emerging literature on service design and design thinking with established strategy theory. Further research will have to

Prostate stereotactic body radiotherapy with simultaneous integrated boost: which is the best planning method?

International Nuclear Information System (INIS)

Tree, Alison; Jones, Caroline; Sohaib, Aslam; Khoo, Vincent; As, Nicholas van

2013-01-01

The delivery of a simultaneous integrated boost to the intra-prostatic tumour nodule may improve local control. The ability to deliver such treatments with hypofractionated SBRT was attempted using RapidArc (Varian Medical systems, Palo Alto, CA) and Multiplan (Accuray inc, Sunnyvale, CA). 15 patients with dominant prostate nodules had RapidArc and Multiplan plans created using a 5 mm isotropic margin, except 3 mm posteriorly, aiming to deliver 47.5 Gy in 5 fractions to the boost whilst treating the whole prostate to 36.25 Gy in 5 fractions. An additional RapidArc plan was created using an 8 mm isotropic margin, except 5 mm posteriorly, to account for lack of intrafraction tracking. Both RapidArc and Multiplan can produce clinically acceptable boost plans to a dose of 47.5 Gy in 5 fractions. The mean rectal doses were lower for RapidArc plans (D50 13.2 Gy vs 15.5 Gy) but the number of missed constraints was the same for both planning methods (11/75). When the margin was increased to 8 mm/5 mm for the RapidArc plans to account for intrafraction motion, 37/75 constraints were missed. RapidArc and Multiplan can produce clinically acceptable simultaneous integrated boost plans, but the mean rectal D50 and D20 with RapidArc are lower. If the margins are increased to account for intrafraction motion, the RapidArc plans exceed at least one dose constraint in 13/15 cases. Delivering a simultaneous boost with hypofractionation appears feasible, but requires small margins needing intrafraction motion tracking

Dual-Input Isolated Full-Bridge Boost DC-DC Converter Based on the Distributed Transformers

DEFF Research Database (Denmark)

Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

2012-01-01

In this paper, a new two-input isolated boost dc-dc converter based on a distributed multi-transformer structure which is suitable for hybrid renewable energy systems is investigated and designed. With a novel transformer winding-connecting strategy, the two input ports can be decoupled completely...... and the single-input mode, respectively. The main advantage of the proposed topology is that the four transformers and the secondary rectifiers are fully utilized whether the converter is connected with two input power sources or only one input. Although the four transformers are employed, the nominal powers...... of each transformer and rectifier are both reduced by four times. Furthermore, some special issues on converter design, such as increasing number of the input ports, the magnetic integration and the ground loop decoupling are discussed. A 2 kW prototype was built and tested. Experiments on the converter...

Design of a High Power Robotic Manipulator for Emergency Response to the Nuclear Accidents

International Nuclear Information System (INIS)

Park, Jongwon; Bae, Yeong-Geol; Kim, Myoung Ho; Choi, Young Soo

2016-01-01

An accident in a nuclear facility causes a great social cost. To prevent an unexpected nuclear accident from spreading to the catastrophic disaster, emergency response action in early stage is required. However, high radiation environment has been proved as a challenging obstacle for human workers to access to the accident site and take an action in previous accident cases. Therefore, emergency response robotic technology to be used in a nuclear accident site instead of human workers are actively conducted in domestically and internationally. Robots in an accident situation are required to carry out a variety of tasks depend on the types and patterns of accidents. An emergency response usually includes removing of debris, make an access road to a certain place and handling valves. These tasks normally involve high payload handling. A small sized high power robotic manipulator can be an appropriate candidate to deal with a wide spectrum of tasks in an emergency situation. In this paper, we discuss about the design of a high power robotic manipulator, which is capable of handling high payloads for an initial response action to the nuclear facility accident. In this paper, we presented a small sized high power robotic manipulator design. Actuator types of manipulator was selected and mechanical structure was discussed. In the future, the servo valve and hydraulic pump systems will be determined. Furthermore, control algorithms and test bed experiments will be also conducted

Design of a High Power Robotic Manipulator for Emergency Response to the Nuclear Accidents

Energy Technology Data Exchange (ETDEWEB)

Park, Jongwon; Bae, Yeong-Geol; Kim, Myoung Ho; Choi, Young Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

An accident in a nuclear facility causes a great social cost. To prevent an unexpected nuclear accident from spreading to the catastrophic disaster, emergency response action in early stage is required. However, high radiation environment has been proved as a challenging obstacle for human workers to access to the accident site and take an action in previous accident cases. Therefore, emergency response robotic technology to be used in a nuclear accident site instead of human workers are actively conducted in domestically and internationally. Robots in an accident situation are required to carry out a variety of tasks depend on the types and patterns of accidents. An emergency response usually includes removing of debris, make an access road to a certain place and handling valves. These tasks normally involve high payload handling. A small sized high power robotic manipulator can be an appropriate candidate to deal with a wide spectrum of tasks in an emergency situation. In this paper, we discuss about the design of a high power robotic manipulator, which is capable of handling high payloads for an initial response action to the nuclear facility accident. In this paper, we presented a small sized high power robotic manipulator design. Actuator types of manipulator was selected and mechanical structure was discussed. In the future, the servo valve and hydraulic pump systems will be determined. Furthermore, control algorithms and test bed experiments will be also conducted.

Superconducting Electric Boost Pump for Nuclear Thermal Propulsion, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A submersible, superconducting electric boost pump sized to meet the needs of future Nuclear Thermal Propulsion systems in the 25,000 lbf thrust range is proposed....

Multistage switched inductor boost converter for renewable energy application

DEFF Research Database (Denmark)

Maroti, Pandav Kiran; Padmanaban, Sanjeevikumar; Bhaskar, Mahajan Sagar

2017-01-01

In this paper Multistage Switched Inductor Boost Converter (Multistage SIBC) is uttered for renewable energy applications. The projected converter is derived from an amalgamation of the conventional step-up converter and inductor stack. The number of inductor and duty ratio decides the overall...

Digitally-controlled PC-interfaced Boost Converter for Educational Purposes

DEFF Research Database (Denmark)

Ljusev, Petar; Andersen, Michael A. E.

2004-01-01

This paper describes implementation of a simple digital PID control algorithm for a boost converter using a cheap fixed-point 8-bit microcontroller. Serial communication to a PC server program is established for easier downloading of compensator parameters and current and voltage waveform...

Designing for Sharing in Local Communities

DEFF Research Database (Denmark)

Malmborg, Lone; Light, Ann; Fitzpatrick, Geraldine

2015-01-01

The Sharing Economy has brought new attention to the everyday practice of sharing. Digital tools are changing both what we can do together across neighbourhoods and how we think about sharing our time, materials and skills. It is possible to design to boost resource management, economic wellbeing...... and social resilience by fostering sharing practices, but do different designs speak to different priorities in design for sharing?...

Designing of a mobile decontamination facility (MDF) for preparedness and response to nuclear/radiological emergencies

International Nuclear Information System (INIS)

Joshi, G.H.; Garai, S.K.; Chatterjee, M.K.; Pradeepkumar, K.S.; Sharma, D.N.

2005-01-01

During a radiological emergency in public domain, likelihood of radioactive contamination cannot be completely ruled out. Timely and effective decontamination can significantly reduce possible external and internal radiation exposure to public. The objective of designing of a mobile decontamination facility is to develop the capability for decontaminating affected persons in case of any radiological emergency in public domain. A fully equipped decontamination facility on the wheels will be able to reach at the scene and will be able to decontaminate a large number of victims with the help of optimized decontamination procedures in short duration avoiding unwanted radiation exposure. This self-supporting decontamination facility is designed to be equipped with sufficient number of radiation monitoring instruments, equipments for decontamination, decontamination agents etc. (author)

Primary Parallel Isolated Boost Converter with Bidirectional Operation

DEFF Research Database (Denmark)

Hernandez Botella, Juan Carlos; Mira Albert, Maria del Carmen; Sen, Gökhan

2012-01-01

This paper presents a bidirectional dc/dc converter operated with batteries both in the input and output. Primary parallel isolated boost converter (PPIBC) with transformer series connection on the high voltage side is preferred due to its ability to handle high currents in the low voltage side. ...... and output battery banks with a defined ramp....

Design Concepts of Emergency Response Robot Platform K-R2D2

Energy Technology Data Exchange (ETDEWEB)

Noh, Sun Young; Jeong, Kyungmin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

From the analysis for various mobile robots competed in DARPA Robotics Challenge, there are some drawbacks in using two or four legs because bipedal locomotion is not yet suitable for maintaining stability and quadrupedal locomotion is difficult to go through narrow aisles. Motivated by the above observations, we propose a K-R2D2 robot platform with three legs arranged in the form of a triangle like as R2-D2 robot which is a fictional robot character in the Star Wars movies. This robot has 3 legs with tracks in each sole of the leg. It is statically stable since there are three contact points to ground. In addition, three legs are also possible to design a structure walking stairs that can expand and contract in the vertical direction. This paper has presented the conceptual design, it is developed on the purpose of quick response instead of emergent workers to the extreme conditions disasters. This robot is emergency response robot platform KR2D2 with three legs, which is statically stable to walk or wheel depending on the terrains and move quickly as possible as on uneven terrain or stairs.

Design Concepts of Emergency Response Robot Platform K-R2D2

International Nuclear Information System (INIS)

Noh, Sun Young; Jeong, Kyungmin

2016-01-01

From the analysis for various mobile robots competed in DARPA Robotics Challenge, there are some drawbacks in using two or four legs because bipedal locomotion is not yet suitable for maintaining stability and quadrupedal locomotion is difficult to go through narrow aisles. Motivated by the above observations, we propose a K-R2D2 robot platform with three legs arranged in the form of a triangle like as R2-D2 robot which is a fictional robot character in the Star Wars movies. This robot has 3 legs with tracks in each sole of the leg. It is statically stable since there are three contact points to ground. In addition, three legs are also possible to design a structure walking stairs that can expand and contract in the vertical direction. This paper has presented the conceptual design, it is developed on the purpose of quick response instead of emergent workers to the extreme conditions disasters. This robot is emergency response robot platform KR2D2 with three legs, which is statically stable to walk or wheel depending on the terrains and move quickly as possible as on uneven terrain or stairs

Boosting structured additive quantile regression for longitudinal childhood obesity data.

Science.gov (United States)

Fenske, Nora; Fahrmeir, Ludwig; Hothorn, Torsten; Rzehak, Peter; Höhle, Michael

2013-07-25

Childhood obesity and the investigation of its risk factors has become an important public health issue. Our work is based on and motivated by a German longitudinal study including 2,226 children with up to ten measurements on their body mass index (BMI) and risk factors from birth to the age of 10 years. We introduce boosting of structured additive quantile regression as a novel distribution-free approach for longitudinal quantile regression. The quantile-specific predictors of our model include conventional linear population effects, smooth nonlinear functional effects, varying-coefficient terms, and individual-specific effects, such as intercepts and slopes. Estimation is based on boosting, a computer intensive inference method for highly complex models. We propose a component-wise functional gradient descent boosting algorithm that allows for penalized estimation of the large variety of different effects, particularly leading to individual-specific effects shrunken toward zero. This concept allows us to flexibly estimate the nonlinear age curves of upper quantiles of the BMI distribution, both on population and on individual-specific level, adjusted for further risk factors and to detect age-varying effects of categorical risk factors. Our model approach can be regarded as the quantile regression analog of Gaussian additive mixed models (or structured additive mean regression models), and we compare both model classes with respect to our obesity data.

The effect of boost pressure on the performance characteristics of a diesel engine: A neuro-fuzzy approach

Energy Technology Data Exchange (ETDEWEB)

Al-Hinti, I.; Sakhrieh, A. [Department of Mechanical Engineering, The Hashemite University, Zarqa 13115 (Jordan); Samhouri, M.; Al-Ghandoor, A. [Department of Industrial Engineering, The Hashemite University, Zarqa 13115 (Jordan)

2009-01-15

This paper uses a neuro-fuzzy interface system (ANFIS) to study the effect of boost pressure on the efficiency, brake mean effective pressure (BMEP), and the brake specific fuel consumption (BSFC) of a single cylinder diesel engine. Experimental data were used as inputs to ANFIS to simulate the engine performance characteristics. The experimental as well as the model results emphasize the role of boost pressure in improving the different engine characteristics. The results show that the ANFIS technique can be used adequately to identify the effect of boost pressure on the different engine characteristics. In addition, different data points that were not used for ANFIS training were used to validate the developed models. The results suggest that ANFIS can be used accurately to predict the effect of boost pressure on the different engine characteristics. (author)

3-D conformal treatment of prostate cancer to 74 Gy vs. high-dose-rate brachytherapy boost: A cross-sectional quality-of-life survey

International Nuclear Information System (INIS)

Vordermark, Dirk

2006-01-01

The effects of two modalities of dose-escalated radiotherapy on health-related quality of life (HRQOL) were compared. Forty-one consecutive patients were treated with a 3-D conformal (3-DC) boost to 74 Gy, and 43 with high-dose rate (HDR) brachytherapy boost (2x9 Gy), following 3-D conformal treatment to 46 Gy. Median age was 70 years in both groups, median initial PSA was 7.9 μg/l in 3-DC boost patients and 8.1 μg/l in HDR boost patients. Stage was 7 in 52% and 47%, respectively. HRQOL was assessed cross-sectionally using EORTC QLQ-C30 and organ-specific PR25 modules 3-32 (median 19) and 4-25 (median 14) months after treatment, respectively. Questionnaires were completed by 93% and 97% of patients, respectively. Diarrhea and insomnia scores were significantly increased in both groups. In the PR25 module, scores of 3-DC boost and HDR boost patients for urinary, bowel and treatment-related symptoms were similar. Among responders, 34% of 3-DC boost patients and 86% of HDR boost patients had severe erectile problems. Dose escalation in prostate cancer by either 3-DC boost to 74 Gy or HDR brachytherapy boost appears to result in similar HRQOL profiles

A cosmetic evaluation of breast cancer treatment: A randomized study of radiotherapy boost technique

International Nuclear Information System (INIS)

Vass, Sylvie; Bairati, Isabelle

2005-01-01

Purpose: To compare cosmetic results of two different radiotherapy (RT) boost techniques used in the treatment of breast cancer after whole breast radiotherapy and to identify factors affecting cosmetic outcomes. Methods and Materials: Between 1996 and 1998, 142 patients with Stage I and II breast cancer were treated with breast conservative surgery and adjuvant RT. Patients were then randomly assigned to receive a boost dose of 15 Gy delivered to the tumor bed either by iridium 192, or a combination of photons and electrons. Cosmetic evaluations were done on a 6-month basis, with a final evaluation at 36 months after RT. The evaluations were done using a panel of global and specific subjective scores, a digitized scoring system using the breast retraction assessment (BRA) measurement, and a patient's self-assessment evaluation. As cosmetic results were graded according to severity, the comparison of boost techniques was done using the ordinal logistic regression model. Adjusted odds ratios (OR) and their 95% confidence intervals (CI) are presented. Results: At 36 months of follow-up, there was no significant difference between the two groups with respect to the global subjective cosmetic outcome (OR = 1.40; 95%CI = 0.69-2.85, p = 0.35). Good to excellent scores were observed in 65% of implant patients and 62% of photon/electron patients. At 24 months and beyond, telangiectasia was more severe in the implant group with an OR of 9.64 (95%CI = 4.05-22.92, p < 0.0001) at 36 months. The only variable associated with a worse global cosmetic outcome was the presence of concomitant chemotherapy (OR = 3.87; 95%CI = 1.74-8.62). The BRA value once adjusted for age, concomitant chemotherapy, and boost volume showed a positive association with the boost technique. The BRA value was significantly greater in the implant group (p 0.03). There was no difference in the patient's final self-assessment score between the two groups. Three variables were statistically associated with

Cash boost to Great British science unveiled

CERN Multimedia

2002-01-01

"Trade and Industry Secretary, Patricia Hewitt today unveiled new plans for the DTI's record science budget over the next three years, to keep Britain at the forefront of world science. The plans include funding to develop life saving new health techniques, to seek alternative energy sources, to help our rural economy, to develop the computers of tomorrow and boost business with the next generation of leading edge technologies" (1 page).

Search for New Physics in Boosted Topologies

CERN Document Server

Cochran, James; The ATLAS collaboration

2014-01-01

The presentation is expected to focus on the opportunities of discovery of new physics profiting of the latest reconstruction tools for boosted top-quark or boson (W,Z,H) reconstruction and their large effect on increasing the analysis efficiency. A summary of Run 1 results showing latest techniques for background suppression and data-driven background estimate should be included pointing out the possibilities and improvements for Run 2.

Orbit Transfer Vehicle (OTV) advanced expander cycle engine point design study. Volume 2: Study results

Science.gov (United States)

1980-01-01

Detailed computer models of the engine were developed to predict both the steady state and transient operation of the engine system. Mechanical design layout drawings were prepared for the following components: thrust chamber and nozzle; extendible nozzle actuating mechanism and seal; LOX turbopump and boost pump; hydrogen turbopump and boost pump; and the propellant control valves. The necessary heat transfer, stress, fluid flow, dynamic, and performance analyses were performed to support the mechanical design.

Can role models boost entrepreneurial attitudes?

Science.gov (United States)

Fellnhofer, Katharina; Puumalainen, Kaisu

2017-01-01

This multi-country study used role models to boost perceptions of entrepreneurial feasibility and desirability. The results of a structural equation model based on a sample comprising 426 individuals who were primarily from Austria, Finland and Greece revealed a significant positive influence on perceived entrepreneurial desirability and feasibility. These findings support the argument for embedding entrepreneurial role models in entrepreneurship education courses to promote entrepreneurial activities. This direction is not only relevant for the academic community but also essential for nascent entrepreneurs, policymakers and society at large.

Mixed Lorentz boosted $Z^{0}'s$

CERN Document Server

Kjaer, N J

2001-01-01

A novel technique is proposed to study systematic errors on jet reconstruction in W physics measurements at LEP2 with high statistical precision. The method is based on the emulation of W pair events using Mixed Lorentz Boosted Z0 events. The scope and merits of the method and its statistical accuracy are discussed in the context of the DELPHI W mass measurement in the fully hadronic channel. The numbers presented are preliminary in the sense that they do not constitute the final DELPHI systematic errors.

Reconstruction of boosted $W^{\\pm}$ and $Z^{0}$ bosons from fat jets

CERN Document Server

Heinrich, Jochen Jens; Petersen, Troels Christian

We present the reconstruction of heavily boosted $W^{\\pm}$ and $Z^{0}$ bosons from large R-parameter jets (fat jets) in all-hadronic proton-proton collisions at $\\sqrt{s} = 8$ TeV at the LHC. The electroweak gauge bosons are boosted to a degree at which their hadronic decay products are collimated enough to be reconstructed as a single fat jet. A mass-drop filtering procedure which is validated in studies on Monte Carlo (MC) samples is then applied to the fat jets with $p_{T} > 420$ GeV to suppress pileup and soft radiation. $W^{\\pm}$ and $Z^{0}$ bosons are identified based on their filtered jet mass. The efficiency of common substructure observables and event shape variables, in distinguishing between signal and QCD background is evaluated on MC and the optimized observable selection used for the training of two boosted decision trees (BDT), in order to reduce the dijet background not originating from the decay of an electroweak gauge boson. For the first BDT, signal MC has been trained against background MC...

Design and Demonstration of Emergency Control Modes for Enhanced Engine Performance

Science.gov (United States)

Liu, Yuan; Litt, Jonathan S.; Guo, Ten-Huei

2013-01-01

A design concept is presented for developing control modes that enhance aircraft engine performance during emergency flight scenarios. The benefits of increased engine performance to overall vehicle survivability during these situations may outweigh the accompanied elevated risk of engine failure. The objective involves building control logic that can consistently increase engine performance beyond designed maximum levels based on an allowable heightened probability of failure. This concept is applied to two previously developed control modes: an overthrust mode that increases maximum engine thrust output and a faster response mode that improves thrust response to dynamic throttle commands. This paper describes the redesign of these control modes and presents simulation results demonstrating both enhanced engine performance and robust maintenance of the desired elevated risk level.

Modeling and Control of Primary Parallel Isolated Boost Converter

DEFF Research Database (Denmark)

Mira Albert, Maria del Carmen; Hernandez Botella, Juan Carlos; Sen, Gökhan

2012-01-01

In this paper state space modeling and closed loop controlled operation have been presented for primary parallel isolated boost converter (PPIBC) topology as a battery charging unit. Parasitic resistances have been included to have an accurate dynamic model. The accuracy of the model has been...

Novel process windows, part 1: Boosted micro process technology

NARCIS (Netherlands)

Hessel, V.; Wang, Q.

2011-01-01

Novel Process Windows (NPW) is the use of highly intensified, unusual and typically harsh process conditions to boost micro process technology and flow chemistry for the production of high-added value fine chemicals, pharmaceuticals, etc.. It is far from conventional processing and also from

Techno-experiential design assessment and media experience database: A method for emerging technology assessment

OpenAIRE

Schick, Dan

2005-01-01

This thesis evaluates the Techno-Experiential Design Assessment (TEDA) for social research on new media and emerging technology. Dr. Roman Onufrijchuk developed TEDA to address the shortcomings of current methods designed for studying existing technologies. Drawing from the ideas of Canadian media theorist Marshall McLuhan, TEDA focuses on the environmental changes introduced by a new technology into a user's life. I describe the key components of the TEDA methodology and provide examples of ...

Implantable electronics: emerging design issues and an ultra light-weight security solution.

Science.gov (United States)

Narasimhan, Seetharam; Wang, Xinmu; Bhunia, Swarup

2010-01-01

Implantable systems that monitor biological signals require increasingly complex digital signal processing (DSP) electronics for real-time in-situ analysis and compression of the recorded signals. While it is well-known that such signal processing hardware needs to be implemented under tight area and power constraints, new design requirements emerge with their increasing complexity. Use of nanoscale technology shows tremendous benefits in implementing these advanced circuits due to dramatic improvement in integration density and power dissipation per operation. However, it also brings in new challenges such as reliability and large idle power (due to higher leakage current). Besides, programmability of the device as well as security of the recorded information are rapidly becoming major design considerations of such systems. In this paper, we analyze the emerging issues associated with the design of the DSP unit in an implantable system. Next, we propose a novel ultra light-weight solution to address the information security issue. Unlike the conventional information security approaches like data encryption, which come at large area and power overhead and hence are not amenable for resource-constrained implantable systems, we propose a multilevel key-based scrambling algorithm, which exploits the nature of the biological signal to effectively obfuscate it. Analysis of the proposed algorithm in the context of neural signal processing and its hardware implementation shows that we can achieve high level of security with ∼ 13X lower power and ∼ 5X lower area overhead than conventional cryptographic solutions.

Romiplostim for the Emergency Management of Severe Immune Thrombocytopenia with Intracerebral Hemorrhage

Directory of Open Access Journals (Sweden)

Romain Gellens

2018-01-01

Full Text Available Currently, we lack well-established guidelines for the emergency management of severe immune thrombocytopenia (ITP with life-threatening bleeding. We now report the management of two patients with severe ITP, complicated by substantial cerebral hemorrhage, requiring urgent surgery due to refractory intracranial hypertension. To rapidly boost platelet counts (PCs, corticosteroids, intravenous immunoglobulin, and iterative platelet transfusions were given; all were ineffectual. Romiplostim, a thrombopoietin receptor agonist, was then administered as an “on demand therapy,” with the result that a rapid and sustained increase of PCs was achieved, thus allowing for postoperative hemostasis. Both patients recovered good neurological condition, suggesting the potential utility of romiplostim, in combined therapy, for the emergency management of severe ITP.

Single stage buck-boost DC-AC neutral point clamped inverter

DEFF Research Database (Denmark)

Mo, Wei; Loh, Poh Chiang; Andrew, A.

2012-01-01

This paper proposes a new single stage buck-boost DC-AC neutral point clamped inverter topology which integrates the cascaded configurations of recently introduced inductor-capacitor-capacitor-transformer impedance source network (by Adamowicz) and classic NPC configuration. As a consequence......, it has enhanced buck-boost functionality and low output voltage distortions compared to the traditional Z-source inverter; it has continuous input current which reduces the source stress and inverter noise; it also contains two built-in capacitors which can block the DC current in the transformer...... windings thus preventing the core from saturation; lowers the voltage stresses and power losses of inverter switches and reduces the sizes of filtering devices and as well as obtains better output performance compared to the original two-level Z-source inverters. A phase disposition pulse width modulation...

Boosted $H\\rightarrow b \\bar{b}$ Tagger in Run II

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00394595; The ATLAS collaboration

2016-01-01

Many searches for Higgs bosons decaying to b quark pairs benefit from the increased Run II centre of mass energy by exploiting the large transverse momentum (boosted) Higgs boson regime, where the two b-jets are merged into one large radius jet. ATLAS uses a boosted $H \\rightarrow b\\bar{b}$ tagger algorithm to separate Higgs signal from background processes (QCD, W and Z bosons, top quarks). The tagger takes as input a large R=1.0 jet with calibrated pseudorapidity, energy and mass scale. It employs b-tagging, Higgs candidate mass, and substructure information. The performance of several operating points in Higgs boson signal, QCD and $t\\bar{t}$ all-hadronic backgrounds are presented. Systematic uncertainties are evaluated so that this tagger can be used in analyses.

Using Boosted Decision Trees to look for displaced Jets in the ATLAS Calorimeter

CERN Multimedia

CERN. Geneva

2017-01-01

A boosted decision tree is used to identify unique jets in a recently released conference note describing a search for long lived particles decaying to hadrons in the ATLAS Calorimeter. Neutral Long lived particles decaying to hadrons are “typical” signatures in a lot of models including Hidden Valley models, Higgs Portal Models, Baryogenesis, Stealth SUSY, etc. Long lived neutral particles that decay in the calorimeter leave behind an object that looks like a regular Standard Model jet, with subtle differences. For example, the later in the calorimeter it decays, the less energy will be deposited in the early layers of the calorimeter. Because the jet does not originate at the interaction point, it will likely be more narrow as reconstructed by the standard Anti-kT jet reconstruction algorithm used by ATLAS. To separate the jets due to neutral long lived decays from the standard model jets we used a boosted decision tree with thirteen variables as inputs. We used the information from the boosted decision...

Heterologous prime-boost vaccinations for poverty-related diseases: advantages and future prospects.

Science.gov (United States)

Radosević, Katarina; Rodriguez, Ariane; Lemckert, Angelique; Goudsmit, Jaap

2009-05-01

Classical vaccination approaches, based on a single vaccine administered in a homologous prime-boost schedule and optimized to induce primarily neutralizing antibodies, are unlikely to be sufficiently efficacious to prevent TB, malaria or HIV infections. Novel vaccines, capable of inducing a more powerful immune response, in particular T-cell immunity, are desperately needed. Combining different vaccine modalities that are able to complement each other and induce broad and sustainable immunity is a promising approach. This review provides an overview of heterologous prime-boost vaccination modalities currently in development for the 'big three' poverty-related diseases and emphasizes the need for innovative vaccination approaches.

3-D conformal treatment of prostate cancer to 74 Gy vs. high-dose-rate brachytherapy boost: A cross-sectional quality-of-life survey

Energy Technology Data Exchange (ETDEWEB)

Vordermark, Dirk [Univ. of Wuerzburg (DE). Dept. of Radiation Oncology] (and others)

2006-09-15

The effects of two modalities of dose-escalated radiotherapy on health-related quality of life (HRQOL) were compared. Forty-one consecutive patients were treated with a 3-D conformal (3-DC) boost to 74 Gy, and 43 with high-dose rate (HDR) brachytherapy boost (2x9 Gy), following 3-D conformal treatment to 46 Gy. Median age was 70 years in both groups, median initial PSA was 7.9 {mu}g/l in 3-DC boost patients and 8.1 {mu}g/l in HDR boost patients. Stage was 7 in 52% and 47%, respectively. HRQOL was assessed cross-sectionally using EORTC QLQ-C30 and organ-specific PR25 modules 3-32 (median 19) and 4-25 (median 14) months after treatment, respectively. Questionnaires were completed by 93% and 97% of patients, respectively. Diarrhea and insomnia scores were significantly increased in both groups. In the PR25 module, scores of 3-DC boost and HDR boost patients for urinary, bowel and treatment-related symptoms were similar. Among responders, 34% of 3-DC boost patients and 86% of HDR boost patients had severe erectile problems. Dose escalation in prostate cancer by either 3-DC boost to 74 Gy or HDR brachytherapy boost appears to result in similar HRQOL profiles.

Intranasal boosting with an adenovirus-vectored vaccine markedly enhances protection by parenteral Mycobacterium bovis BCG immunization against pulmonary tuberculosis.

Science.gov (United States)

Santosuosso, Michael; McCormick, Sarah; Zhang, Xizhong; Zganiacz, Anna; Xing, Zhou

2006-08-01

Parenterally administered Mycobacterium bovis BCG vaccine confers only limited immune protection from pulmonary tuberculosis in humans. There is a need for developing effective boosting vaccination strategies. We examined a heterologous prime-boost regimen utilizing BCG as a prime vaccine and our recently described adenoviral vector expressing Ag85A (AdAg85A) as a boost vaccine. Since we recently demonstrated that a single intranasal but not intramuscular immunization with AdAg85A was able to induce potent protection from pulmonary Mycobacterium tuberculosis challenge in a mouse model, we compared the protective effects of parenteral and mucosal booster immunizations following subcutaneous BCG priming. Protection by BCG prime immunization was not effectively boosted by subcutaneous BCG or intramuscular AdAg85A. In contrast, protection by BCG priming was remarkably boosted by intranasal AdAg85A. Such enhanced protection by intranasal AdAg85A was correlated to the numbers of gamma interferon-positive CD4 and CD8 T cells residing in the airway lumen of the lung. Our study demonstrates that intranasal administration of AdAg85A represents an effective way to boost immune protection by parenteral BCG vaccination.

Award-winning machine boosts sorghum farming in Sudan | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

2016-04-28

Apr 28, 2016 ... Award-winning machine boosts sorghum farming in Sudan ... The new planter, developed by researchers at Sudan's Agricultural ... Senegal: Staying home at all costs ... This ICT4D article series features results from innovative research on participatory geographic information systems (P-GIS) in Africa.

Tricky treats: how and when temptations boost self-control

NARCIS (Netherlands)

Kroese, F.M.|info:eu-repo/dai/nl/313869871

2012-01-01

The overall aim of this dissertation was to explore how and when temptations boost self-control. More specifically, we aimed to a) replicate and extend previous findings showing that temptations yield enhanced self-control on cognitive as well as behavioral measures; b) examine the role of

A prediction model of short-term ionospheric foF2 based on AdaBoost

Science.gov (United States)

Zhao, Xiukuan; Ning, Baiqi; Liu, Libo; Song, Gangbing

2014-02-01

In this paper, the AdaBoost-BP algorithm is used to construct a new model to predict the critical frequency of the ionospheric F2-layer (foF2) one hour ahead. Different indices were used to characterize ionospheric diurnal and seasonal variations and their dependence on solar and geomagnetic activity. These indices, together with the current observed foF2 value, were input into the prediction model and the foF2 value at one hour ahead was output. We analyzed twenty-two years' foF2 data from nine ionosonde stations in the East-Asian sector in this work. The first eleven years' data were used as a training dataset and the second eleven years' data were used as a testing dataset. The results show that the performance of AdaBoost-BP is better than those of BP Neural Network (BPNN), Support Vector Regression (SVR) and the IRI model. For example, the AdaBoost-BP prediction absolute error of foF2 at Irkutsk station (a middle latitude station) is 0.32 MHz, which is better than 0.34 MHz from BPNN, 0.35 MHz from SVR and also significantly outperforms the IRI model whose absolute error is 0.64 MHz. Meanwhile, AdaBoost-BP prediction absolute error at Taipei station from the low latitude is 0.78 MHz, which is better than 0.81 MHz from BPNN, 0.81 MHz from SVR and 1.37 MHz from the IRI model. Finally, the variety characteristics of the AdaBoost-BP prediction error along with seasonal variation, solar activity and latitude variation were also discussed in the paper.

Hybrid Non-Isolated and Non Inverting Nx Interleaved DC-DC Multilevel Boost Converter for Renewable Energy Applications

DEFF Research Database (Denmark)

Bhaskar, Mahajan Sagar; Kulkarni, Rishi M.; Padmanaban, Sanjeevi Kumar

2016-01-01

In this paper hybrid non isolated/ non inverting Nx interleaved DC-DC multilevel Boost Converter for renewable energy applications is presented. The presented hybrid topology is derived from the conventional interleaved converter and the Nx Multilevel boost converter. In renewable energy...... applications, generated energy cannot be directly used at application end. In most of the cases it needs to be stepped up with DC-DC converter at operating voltage levels as per the requirement of the application. Though conventional boost converter can theoretically be used for this purpose, but obtaining...

The Role of Concomitant Radiation Boost in Neoadjuvant Chemoradiotherapy for Locally Advanced Rectal Cancer.

Science.gov (United States)

Badakhshi, Harun; Ismail, Mahmoud; Boskos, Christos; Zhao, Kuaile; Kaul, David

2017-06-01

This study analyzed the impact of concomitant boost on long-term clinical outcomes in locally advanced rectal cancer. A total of 141 patients (median age=61 years) were treated with neoadjuvant chemoradiotherapy. Median total dose was 50.4 Gy. Forty-three patients received a concomitant boost. Concurrent chemotherapy consisted of 5-fluorouracil (5-FU), given as a 24-h continuous infusion. Mean follow-up was 83.7 months. The 3, 5-, and 10-year overall survival (OS) rates were 91.9%, 84.6%, and 52.9%, respectively. Recurrence-free survival (RFS) rates at 3, 5, and 10 years were 91.4%, 88.9%, and 79.3%, respectively. Metastasis-free survival (MFS) rates at 3, 5, and 10 years were 84.6%, 75.4%, and 49.9%, respectively. Overall, 9.9% of all patients achieved pathological complete response. Down-staging of T- or N-stage was achieved in 55.1% and 41.5% of patients. Multivariate analysis revealed that female sex (p=0.011), concomitant boost-radiotherapy (p=0.014), and the presence of fewer than five positive lymph nodes (prectal cancer in terms of local outcomes. Intensified radiotherapy using a concomitant boost has a positive effect on OS. Copyright© 2017, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

Urban Link Travel Time Prediction Based on a Gradient Boosting Method Considering Spatiotemporal Correlations

Directory of Open Access Journals (Sweden)

Faming Zhang

2016-11-01

Full Text Available The prediction of travel times is challenging because of the sparseness of real-time traffic data and the intrinsic uncertainty of travel on congested urban road networks. We propose a new gradient–boosted regression tree method to accurately predict travel times. This model accounts for spatiotemporal correlations extracted from historical and real-time traffic data for adjacent and target links. This method can deliver high prediction accuracy by combining simple regression trees with poor performance. It corrects the error found in existing models for improved prediction accuracy. Our spatiotemporal gradient–boosted regression tree model was verified in experiments. The training data were obtained from big data reflecting historic traffic conditions collected by probe vehicles in Wuhan from January to May 2014. Real-time data were extracted from 11 weeks of GPS records collected in Wuhan from 5 May 2014 to 20 July 2014. Based on these data, we predicted link travel time for the period from 21 July 2014 to 25 July 2014. Experiments showed that our proposed spatiotemporal gradient–boosted regression tree model obtained better results than gradient boosting, random forest, or autoregressive integrated moving average approaches. Furthermore, these results indicate the advantages of our model for urban link travel time prediction.

Malampaya to boost flow of foreign investment

International Nuclear Information System (INIS)

Skrebowski, C.

1995-01-01

The petroleum industry in the Philippines has recently enjoyed a boost with the commissioning of a new modern refinery, and the development of sophisticated off-shore technology in the Malampaya/Camago oil and gas field. The foreign investment, which has made these initiatives possible, came about because of the countries new found political stability. It also reflects the rapid economic growth which has occurred and the accompanying increase in energy demand. (UK)

Study of an innovative ejector heat pump-boosted district heating system

International Nuclear Information System (INIS)

Zhang, Bo; Wang, Yuanchao; Kang, Lisha; Lv, Jinsheng

2013-01-01

An Ejector heat pump-boosted District Heating (EDH) system is proposed to improve the heating capacity of existing district heating systems with Combined Heat and Power (CHP). In the EDH, two ejector heat pumps are installed: a primary heat pump (HP 1 ) at the heating station and a secondary heat pump (HP 2 ) at the heating substation. With the EDH, the low-grade waste heat from circulating cooling water in the CHP is recycled and the temperature difference between the water supply and the return of the primary heating network is increased. A thermodynamic model was provided. An experimental study was carried out for both HP 1 and HP 2 to verify the predicting performance. The results show that the COP of HP 1 can reach 1.5–1.9, and the return water temperature of the primary heating network could be decreased to 35 °C with HP 2 . A typical case study for the EDH was analyzed. -- Highlights: • An ejector heat pump-boosted district heating (EDH) is proposed. • The 1st ejector heat pump in EDH recycles heat from cooling water of the CHP. • The 2nd ejector heat pump in EDH boosts the thermal energy utilization of the primary heating network. • Modeling and experimental studies are presented

Dose analysis of boost irradiation of parapharyngeal space in nasopharyngeal carcinoma

International Nuclear Information System (INIS)

Wu, V.W.C.

2000-01-01

Parapharyngeal space (PPS) is one of the common spreads of nasopharyngeal carcinoma (NPC). Since early eighties boost treatment has been routinely given to patients with PPS involvement. The use of oblique facio-cervical field in this treatment posed difficulty in assessing the dose distribution before the 3-D computer systems are available. This study evaluated the variations of dose distribution by different boost techniques on fifteen patients with PPS involvement using 3-D computer planning system. Comparisons were made between different radiation types, photon energies and modes of collimation respectively. Results showed that the dose distributions in the boost treatment were acceptable, as they did not bring the total doses of the normal structures exceeding their tolerance. There was little difference between 6 and 10 MV photons, but significant differences were found between photon and electron beams. Photon beams were better than the electron beams in giving lower doses to the spinal cord and the TM joint with more homogeneous dose to the target volume, whereas electron beams gave better sparing of the lens and temporal lobe. For the photon beams, half-blocked beam was superior to symmetrical beam in reducing the brain stem dose, but there was no advantage to the rest of normal structures. Copyright (1999) Australian Institute of Radiography

Thermal Performance and Efficiency Investigation of Conventional Boost, Z-source and Y-source Converters

DEFF Research Database (Denmark)

Gadalla, Brwene Salah Abdelkarim; Schaltz, Erik; Siwakoti, Yam Prasad

2016-01-01

Boost converters are needed in many applications that require the output voltage to be higher than the input voltage. Recently, boost type converters have been attracted by the industrial applications, and hence it has become an extremely hot topic of research. Recently, many researchers proposed...... the impedance source converters with their unique advantages as having a high voltage gain in a small range of duty cycle ratio. However, the thermal behaviour of the semiconductor devices and passive elements in the impedance source converter is an important issue from a reliability point of view and has...... not been investigated yet. Therefore this paper presents a comparison between the conventional boost, the Z-source, and the Y-source converters based on the thermal evaluation of semiconductors. In addition, the three topologies are also compared with respect to their efficiency. The operational principle...

Five-Level Current-Source Inverters With Buck–Boost and Inductive-Current Balancing Capabilities

DEFF Research Database (Denmark)

Gao, Feng; Loh, Poh Chiang; Blaabjerg, Frede

2010-01-01

This paper presents new five-level current-source inverters (CSIs) with voltage/current buck–boost capability, unlike existing five-level CSIs where only voltage–boost operation is supported. The proposed inverters attain self-inductive-currentbalancing per switching cycle at their dc front ends...... without having to include additional balancing hardware or complex control manipulation. The inverters can conveniently be controlled by using the well-established phase-shifted carrier modulation scheme with only two additional linear references and a mapping logic table needed. Existing modulators can...

A new DC/AC boost transformerless converter in application of photovoltaic power generation

DEFF Research Database (Denmark)

Wei, Mo; Loh, Poh Chiang; Blaabjerg, Frede

2011-01-01

This paper presents a new DC/AC boost transformerless converter in the applications of photovoltaic (PV) power generation. A new circuit topology of single phase full bridge power inverter with additional DC/DC boost stage is proposed. The proposed topology overcomes two commonly existing......, and then converts the DC into AC to supply the load. A special modulation technique is proposed to eliminate the leakage current which is commonly presents in PV transformerless power generation, helps to increase the system efficiency and output performance....

Regeneration-associated macrophages: a novel approach to boost intrinsic regenerative capacity for axon regeneration

Directory of Open Access Journals (Sweden)

Min Jung Kwon

2016-01-01

Full Text Available Axons in central nervous system (CNS do not regenerate spontaneously after injuries such as stroke and traumatic spinal cord injury. Both intrinsic and extrinsic factors are responsible for the regeneration failure. Although intensive research efforts have been invested on extrinsic regeneration inhibitors, the extent to which glial inhibitors contribute to the regeneration failure in vivo still remains elusive. Recent experimental evidence has rekindled interests in intrinsic factors for the regulation of regeneration capacity in adult mammals. In this review, we propose that activating macrophages with pro-regenerative molecular signatures could be a novel approach for boosting intrinsic regenerative capacity of CNS neurons. Using a conditioning injury model in which regeneration of central branches of dorsal root ganglia sensory neurons is enhanced by a preceding injury to the peripheral branches, we have demonstrated that perineuronal macrophages surrounding dorsal root ganglia neurons are critically involved in the maintenance of enhanced regeneration capacity. Neuron-derived chemokine (C-C motif ligand 2 (CCL2 seems to mediate neuron-macrophage interactions conveying injury signals to perineuronal macrophages taking on a soley pro-regenerative phenotype, which we designate as regeneration-associated macrophages (RAMs. Manipulation of the CCL2 signaling could boost regeneration potential mimicking the conditioning injury, suggesting that the chemokine-mediated RAM activation could be utilized as a regenerative therapeutic strategy for CNS injuries.

Rancang Bangun Penstabil Tegangan pada Pembangkit Termoelektrik Skala Pico Berbasis Boost Converter

Directory of Open Access Journals (Sweden)

Ailin Rohmatul Fajria

2017-05-01

Full Text Available Least of using thermoelectric module as an electric generator in society was often because of energy which was produced by it was unstable. So we need  voltage stabilizer circuit to push up and down the voltage to certain voltage. The purpose of this final project is to design a voltage stabilizer circuit in pico scale DC voltage based on boost converter. This experiment is done by three stage there are, stabilizer experiment by adaptor, performance of thermoelectric generator and also stabilizer experiment by thermoelectric generator. The yield of the first experiment, when we gave input voltage 3 until 9 V produced 5,07 until 5,08 V, so it has 98,55% accuracy toward 5 V expect. On the second experiment, when it is given by ∆T 30, 50 and 70 °C produced 2,5, 3,04 and 3,39 V. While on third experiment, with the same ∆T produced 5,08 until 5,09 V. But, when ∆T which given by 12 °C produced only 0,8 and 0,9 V in second and third experiment, it is because of the voltage is not fulfill accupation voltage 2 until 24 V on datasheet of used IC. Relation between ∆T and Voltage (V, Current (I  also Power (P which was produced have positive R value 0,76 until 1, this mean that ∆T directly proportional to V,I and P. So, the higher ∆T we give, the higher V, I and P will be. Keywords : stabilizer, thermoelectric, boost converter.

EPPM and willingness to respond: the role of risk and efficacy communication in strengthening public health emergency response systems.

Science.gov (United States)

Barnett, Daniel J; Thompson, Carol B; Semon, Natalie L; Errett, Nicole A; Harrison, Krista L; Anderson, Marilyn K; Ferrell, Justin L; Freiheit, Jennifer M; Hudson, Robert; McKee, Mary; Mejia-Echeverry, Alvaro; Spitzer, James; Balicer, Ran D; Links, Jonathan M; Storey, J Douglas

2014-01-01

This study examines the attitudinal impact of an Extended Parallel Process Model (EPPM)-based training curriculum on local public health department (LHD) workers' willingness to respond to representative public health emergency scenarios. Data are from 71 U.S. LHDs in urban and rural settings across nine states. The study explores changes in response willingness and EPPM threat and efficacy appraisals between randomly assigned control versus intervention health departments, at baseline and 1 week post curriculum, through an EPPM-based survey/resurvey design. Levels of response willingness and emergency response-related attitudes/beliefs are measured. Analyses focus on two scenario categories that have appeared on a U.S. government list of scenarios of significant concern: a weather-related emergency and a radiological "dirty" bomb event (U.S. Department of Homeland Security, 2007). The greatest impact from the training intervention on response willingness was observed among LHD workers who had low levels of EPPM-related threat and efficacy perceptions at baseline. Self-efficacy and response efficacy and response willingness increased in intervention LHDs for both scenarios, with greater response willingness increases observed for the radiological "dirty" bomb terrorism scenario. Findings indicate the importance of building efficacy versus enhancing threat perceptions as a path toward greater response willingness, and suggest the potential applicability of such curricular interventions for boosting emergency response willingness among other cadres of health providers.

Closed-loop analysis and control of a non-inverting buck-boost converter

Science.gov (United States)

Chen, Zengshi; Hu, Jiangang; Gao, Wenzhong

2010-11-01

In this article, a cascade controller is designed and analysed for a non-inverting buck-boost converter. The fast inner current loop uses sliding mode control. The slow outer voltage loop uses the proportional-integral (PI) control. Stability analysis and selection of PI gains are based on the nonlinear closed-loop error dynamics incorporating both the inner and outer loop controllers. The closed-loop system is proven to have a nonminimum phase structure. The voltage transient due to step changes of input voltage or resistance is predictable. The operating range of the reference voltage is discussed. The controller is validated by a simulation circuit. The simulation results show that the reference output voltage is well-tracked under system uncertainties or disturbances, confirming the validity of the proposed controller.

Automated Detection of Driver Fatigue Based on AdaBoost Classifier with EEG Signals

Directory of Open Access Journals (Sweden)

Jianfeng Hu

2017-08-01

Full Text Available Purpose: Driving fatigue has become one of the important causes of road accidents, there are many researches to analyze driver fatigue. EEG is becoming increasingly useful in the measuring fatigue state. Manual interpretation of EEG signals is impossible, so an effective method for automatic detection of EEG signals is crucial needed.Method: In order to evaluate the complex, unstable, and non-linear characteristics of EEG signals, four feature sets were computed from EEG signals, in which fuzzy entropy (FE, sample entropy (SE, approximate Entropy (AE, spectral entropy (PE, and combined entropies (FE + SE + AE + PE were included. All these feature sets were used as the input vectors of AdaBoost classifier, a boosting method which is fast and highly accurate. To assess our method, several experiments including parameter setting and classifier comparison were conducted on 28 subjects. For comparison, Decision Trees (DT, Support Vector Machine (SVM and Naive Bayes (NB classifiers are used.Results: The proposed method (combination of FE and AdaBoost yields superior performance than other schemes. Using FE feature extractor, AdaBoost achieves improved area (AUC under the receiver operating curve of 0.994, error rate (ERR of 0.024, Precision of 0.969, Recall of 0.984, F1 score of 0.976, and Matthews correlation coefficient (MCC of 0.952, compared to SVM (ERR at 0.035, Precision of 0.957, Recall of 0.974, F1 score of 0.966, and MCC of 0.930 with AUC of 0.990, DT (ERR at 0.142, Precision of 0.857, Recall of 0.859, F1 score of 0.966, and MCC of 0.716 with AUC of 0.916 and NB (ERR at 0.405, Precision of 0.646, Recall of 0.434, F1 score of 0.519, and MCC of 0.203 with AUC of 0.606. It shows that the FE feature set and combined feature set outperform other feature sets. AdaBoost seems to have better robustness against changes of ratio of test samples for all samples and number of subjects, which might therefore aid in the real-time detection of driver

Congress OKs $2 Billion Boost for the NIH.

Science.gov (United States)

2017-07-01

President Donald Trump last week signed a $1.1 trillion spending bill for fiscal year 2017, including a welcome $2 billion boost for the NIH that will support former Vice President Joe Biden's Cancer Moonshot initiative, among other priorities. However, researchers who rely heavily on NIH grant funding remain concerned about proposed cuts for 2018. ©2017 American Association for Cancer Research.

New Technique for Voltage Tracking Control of a Boost Converter Based on the PSO Algorithm and LTspice

DEFF Research Database (Denmark)

Farhang, Peyman; Drimus, Alin; Mátéfi-Tempfli, Stefan

2015-01-01

In this paper, a new technique is proposed to design a Modified PID (MPID) controller for a Boost converter. An interface between LTspice and MATLAB is carried out to implement the Particle Swarm Optimization (PSO) algorithm. The PSO algorithm which has the appropriate capability to find out...... the optimal solutions is run in MATLAB while it is interfaced with LTspice for simulation of the circuit using actual component models obtained from manufacturers. The PSO is utilized to solve the optimization problem in order to find the optimal parameters of MPID and PID controllers. The performances...

Effects of hyperbolic rotation in Minkowski space on the modeling of plasma accelerators in a Lorentz boosted frame

International Nuclear Information System (INIS)

Vay, J.-L.; Geddes, C. G. R.; Cormier-Michel, E.; Grote, D. P.

2011-01-01

The effects of hyperbolic rotation in Minkowski space resulting from the use of Lorentz boosted frames of calculation on laser propagation in plasmas are analyzed. Selection of a boost frame at the laser group velocity is shown to alter the laser spectrum, allowing the use of higher boost velocities. The technique is applied to simulations of laser driven plasma wakefield accelerators, which promise much smaller machines and whose development requires detailed simulations that challenge or exceed current capabilities. Speedups approaching the theoretical optima are demonstrated, producing the first direct simulations of stages up to 1 TeV. This is made possible by a million times speedup thanks to a frame boost with a relativistic factor γ b as high as 1300, taking advantage of the rotation to mitigate an instability that limited previous work.

Study Of Boosted W-Jets And Higgs-Jets With the SiFCC Detector

Energy Technology Data Exchange (ETDEWEB)

Yu, Shin-Shan [Taiwan, Natl. Central U.; Chekanov, Sergei [Argonne; Gray, Lindsey [Fermilab; Kotwal, Ashutosh [Duke U.; Sen, Sourav [Duke U.; Tran, Nhan Viet [Fermilab

2016-11-04

We study the detector performance in the reconstruction of hadronically-decaying W bosons and Higgs bosons at very high energy proton colliders using a full GEANT4 simulation of the SiFCC detector. The W and Higgs bosons carry transverse momentum in the multi-TeV range, which results in collimated decay products that are reconstructed as a single jet. We present a measurement of the energy response and resolution of boosted W-jets and Higgs-jets and show the separation of two sub-jets within the boosted boson jet.

ATLAS boosted object tagging 2

CERN Document Server

Caudron, Julien; The ATLAS collaboration

2015-01-01

A detailed study into the optimal techniques for identifying boosted hadronically decaying W or Z bosons is presented. Various algorithms for reconstructing, grooming and tagging bosonic jets are compared for W bosons with a wide range of transverse momenta using 8 TeV data and 8 TeV and 13 TeV MC simulations. In addition, given that a hadronic jet has been identified as resulting from the hadronic decay of a W or Z, a technique is developed to discriminate between W and Z bosons. The modeling of the tagging variables used in this technique is studied using 8 TeV pp collision data and systematic uncertainties for the tagger efficiency and fake rates are evaluated.

Development of an Easy-to-Use Tool for the Assessment of Emergency Department Physical Design

Directory of Open Access Journals (Sweden)

Alireza Majidi

2014-03-01

Full Text Available Physical design of the emergency department (ED has an important effect on its role and function. To date, no guidelines have been introduced to set the standards for the construction of EDs in Iran. In this study we aim to devise an easy-to-use tool based on the available literature and expert opinion for the quick and effective assessment of EDs in regards to their physical design. For this purpose, based on current literature on emergency design, a comprehensive checklist was developed.  Then, this checklist was analyzed by a panel consisting of heads of three major EDs and contradicting items were decided. Overall 178 crude items were derived from available literature. The Items were categorized in to three major domains of Physical space, Equipment, and Accessibility. The final checklist approved by the panel consisted of 163 items categorized into six domains. Each item was phrased as a “Yes or No” question for ease of analysis, meaning that the criterion is either met or not. 

ASCENDE-RT: An Analysis of Treatment-Related Morbidity for a Randomized Trial Comparing a Low-Dose-Rate Brachytherapy Boost with a Dose-Escalated External Beam Boost for High- and Intermediate-Risk Prostate Cancer

International Nuclear Information System (INIS)

Rodda, Sree; Tyldesley, Scott; Morris, W. James; Keyes, Mira; Halperin, Ross; Pai, Howard; McKenzie, Michael; Duncan, Graeme; Morton, Gerard; Hamm, Jeremy; Murray, Nevin

2017-01-01

Purpose: To report the genitourinary (GU) and gastrointestinal (GI) morbidity and erectile dysfunction in a randomized trial comparing 2 methods of dose escalation for high- and intermediate-risk prostate cancer. Methods and Materials: ASCENDE-RT (Androgen Suppression Combined with Elective Nodal and Dose Escalated Radiation Therapy) enrolled 398 men, median age 68 years, who were then randomized to either a standard arm that included 12 months of androgen deprivation therapy and pelvic irradiation to 46 Gy followed by a dose-escalated external beam radiation therapy (DE-EBRT) boost to 78 Gy, or an experimental arm that substituted a low-dose-rate prostate brachytherapy (LDR-PB) boost. At clinic visits, investigators recorded GU and GI morbidity and information on urinary continence, catheter use, and erectile function. Exclusion of 15 who received nonprotocol treatment and correction of 14 crossover events left 195 men who actually received a DE-EBRT boost and 188, an LDR-PB boost. Median follow-up was 6.5 years. Results: The LDR-PB boost increased the risk of needing temporary catheterization and/or requiring incontinence pads. At 5 years the cumulative incidence of grade 3 GU events was 18.4% for LDR-PB, versus 5.2% for DE-EBRT (P<.001). Compared with the cumulative incidence, the 5-year prevalence of grade 3 GU morbidity was substantially lower for both arms (8.6% vs 2.2%, P=.058). The 5-year cumulative incidence of grade 3 GI events was 8.1% for LDR-PB, versus 3.2% for DE-EBRT (P=.124). The 5-year prevalence of grade 3 GI toxicity was lower than the cumulative incidence for both arms (1.0% vs 2.2%, respectively). Among men reporting adequate baseline erections, 45% of LDR-PB patients reported similar erectile function at 5 years, versus 37% after DE-EBRT (P=.30). Conclusions: The incidence of acute and late GU morbidity was higher after LDR-PB boost, and there was a nonsignificant trend for worse GI morbidity. No differences in the frequency of

ASCENDE-RT: An Analysis of Treatment-Related Morbidity for a Randomized Trial Comparing a Low-Dose-Rate Brachytherapy Boost with a Dose-Escalated External Beam Boost for High- and Intermediate-Risk Prostate Cancer

Energy Technology Data Exchange (ETDEWEB)

Rodda, Sree [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Tyldesley, Scott [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); Morris, W. James, E-mail: jmorris@bccancer.bc.ca [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); Keyes, Mira [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); Halperin, Ross [Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); BC Cancer Agency, Centre for the Southern Interior, Kelowna, British Columbia (Canada); Pai, Howard [Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); BC Cancer Agency, Vancouver Island Centre, Victoria, British Columbia (Canada); McKenzie, Michael; Duncan, Graeme [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Department of Surgery, University of British Columbia, Vancouver, British Columbia (Canada); Morton, Gerard [Sunnybrook Health Sciences Centre, Toronto, Ontario (Canada); Department of Radiation Oncology, University of Toronto, Toronto, Ontario (Canada); Hamm, Jeremy [Department of Population Oncology, BC Cancer Agency, Vancouver, British Columbia (Canada); Murray, Nevin [British Columbia (BC) Cancer Agency, Vancouver Centre, Vancouver, British Columbia (Canada); Department of Medicine, University of British Columbia, Vancouver, British Columbia (Canada)

2017-06-01

Purpose: To report the genitourinary (GU) and gastrointestinal (GI) morbidity and erectile dysfunction in a randomized trial comparing 2 methods of dose escalation for high- and intermediate-risk prostate cancer. Methods and Materials: ASCENDE-RT (Androgen Suppression Combined with Elective Nodal and Dose Escalated Radiation Therapy) enrolled 398 men, median age 68 years, who were then randomized to either a standard arm that included 12 months of androgen deprivation therapy and pelvic irradiation to 46 Gy followed by a dose-escalated external beam radiation therapy (DE-EBRT) boost to 78 Gy, or an experimental arm that substituted a low-dose-rate prostate brachytherapy (LDR-PB) boost. At clinic visits, investigators recorded GU and GI morbidity and information on urinary continence, catheter use, and erectile function. Exclusion of 15 who received nonprotocol treatment and correction of 14 crossover events left 195 men who actually received a DE-EBRT boost and 188, an LDR-PB boost. Median follow-up was 6.5 years. Results: The LDR-PB boost increased the risk of needing temporary catheterization and/or requiring incontinence pads. At 5 years the cumulative incidence of grade 3 GU events was 18.4% for LDR-PB, versus 5.2% for DE-EBRT (P<.001). Compared with the cumulative incidence, the 5-year prevalence of grade 3 GU morbidity was substantially lower for both arms (8.6% vs 2.2%, P=.058). The 5-year cumulative incidence of grade 3 GI events was 8.1% for LDR-PB, versus 3.2% for DE-EBRT (P=.124). The 5-year prevalence of grade 3 GI toxicity was lower than the cumulative incidence for both arms (1.0% vs 2.2%, respectively). Among men reporting adequate baseline erections, 45% of LDR-PB patients reported similar erectile function at 5 years, versus 37% after DE-EBRT (P=.30). Conclusions: The incidence of acute and late GU morbidity was higher after LDR-PB boost, and there was a nonsignificant trend for worse GI morbidity. No differences in the frequency of

New conceptual design of portable bamboo bridge for emergency purposes

Science.gov (United States)

Musthaffa, A. A.; Nor, N. M.; Yusof, M. A.; Yuhazri, M. Y.

2018-02-01

Portable bridges serve as routes for troops during the military operations and the disaster relief operation. Nowadays, bamboo has been regarded as one of the alternative construction materials for building and bridge structures. This paper presents the conceptual design of the portable bridge. Several types of portable bridges and bamboo bridges are reviewed in the current work. The characteristics, capability and method of construction of each bridge are discussed. Finally, the conceptual of the portable bamboo bridge for emergency purposes is presented. The idea of producing portable bridge is proposed in the current work as it is crucial for providing route for communities affected by natural disasters.

Glucose starvation boosts Entamoeba histolytica virulence.

Directory of Open Access Journals (Sweden)

Ayala Tovy

2011-08-01

Full Text Available The unicellular parasite, Entamoeba histolytica, is exposed to numerous adverse conditions, such as nutrient deprivation, during its life cycle stages in the human host. In the present study, we examined whether the parasite virulence could be influenced by glucose starvation (GS. The migratory behaviour of the parasite and its capability to kill mammalian cells and to lyse erythrocytes is strongly enhanced following GS. In order to gain insights into the mechanism underlying the GS boosting effects on virulence, we analyzed differences in protein expression levels in control and glucose-starved trophozoites, by quantitative proteomic analysis. We observed that upstream regulatory element 3-binding protein (URE3-BP, a transcription factor that modulates E.histolytica virulence, and the lysine-rich protein 1 (KRiP1 which is induced during liver abscess development, are upregulated by GS. We also analyzed E. histolytica membrane fractions and noticed that the Gal/GalNAc lectin light subunit LgL1 is up-regulated by GS. Surprisingly, amoebapore A (Ap-A and cysteine proteinase A5 (CP-A5, two important E. histolytica virulence factors, were strongly down-regulated by GS. While the boosting effect of GS on E. histolytica virulence was conserved in strains silenced for Ap-A and CP-A5, it was lost in LgL1 and in KRiP1 down-regulated strains. These data emphasize the unexpected role of GS in the modulation of E.histolytica virulence and the involvement of KRiP1 and Lgl1 in this phenomenon.

Site-Specific Soundscape Design for the Creation of Sonic Architectures and the Emergent Voices of Buildings

Directory of Open Access Journals (Sweden)

Jordan Lacey

2014-01-01

Full Text Available Does a building contain its own Voice? And if so, can that Voice be discovered, transformed and augmented by soundscape design? Barry Blesser’s writings on acoustic space, discuss reverberation and resonant frequencies as providing architectural spaces with characteristic listening conditions related to the architectural space’s dimensions and materiality. The paper argues that Blesser and Salter expand such discussion into pantheistic speculation when suggesting that humanity contains the imaginative capacity to experience spaces as “living spirits”. This argument is achieved by building on the speculation through the discussion of a soundscape design methodology that considers space as containing pantheistic qualities. Sonic architectures are created with electroacoustic sound installations that recompose existing architectural soundscapes, to create the conditions for the emergence of the Voices of buildings. This paper describes two soundscape designs, Revoicing the Striated Soundscape and Subterranean Voices, which transformed existing architectural soundscapes for the emergence of Voices in a laneway and a building located in the City of Melbourne, Australia.

Higher-Order Hybrid Gaussian Kernel in Meshsize Boosting Algorithm

African Journals Online (AJOL)

In this paper, we shall use higher-order hybrid Gaussian kernel in a meshsize boosting algorithm in kernel density estimation. Bias reduction is guaranteed in this scheme like other existing schemes but uses the higher-order hybrid Gaussian kernel instead of the regular fixed kernels. A numerical verification of this scheme ...

Adaptive Kernel In The Bootstrap Boosting Algorithm In KDE ...

African Journals Online (AJOL)

This paper proposes the use of adaptive kernel in a bootstrap boosting algorithm in kernel density estimation. The algorithm is a bias reduction scheme like other existing schemes but uses adaptive kernel instead of the regular fixed kernels. An empirical study for this scheme is conducted and the findings are comparatively ...

FULL ELECTROMAGNETIC SIMULATION OF COHERENT SYNCHROTRON RADIATION VIA THE LORENTZ-BOOSTED FRAME APPROACH

International Nuclear Information System (INIS)

Fawley, William M.; Vay, Jean-Luc

2010-01-01

Numerical simulation of some systems containing charged particles with highly relativistic directed motion can by speeded up by orders of magnitude by choice of the proper Lorentz-boosted frame. Orders of magnitude speedup has been demonstrated for simulations from first principles of laser-plasma accelerator, free electron laser, and particle beams interacting with electron clouds. Here we address the application of the Lorentz-boosted frame approach to coherent synchrotron radiation (CSR), which can be strongly present in bunch compressor chicanes. CSR is particularly relevant to the next generation of x-ray light sources and is simultaneously difficult to simulate in the lab frame because of the large ratio of scale lengths. It can increase both the incoherent and coherent longitudinal energy spread, effects that often lead to an increase in transverse emittance. We have adapted the WARP code to simulate CSR emission along a simple dipole bend. We present some scaling arguments for the possible computational speed up factor in the boosted frame and initial 3D simulation results.

Cura Annonae-Chemically Boosting Crop Yields Through Metabolic Feeding of a Plant Signaling Precursor.

Science.gov (United States)

Vocadlo, David J

2017-05-22

The cream of the crop: With the world facing a projected shortfall of crops by 2050, new approaches are needed to boost crop yields. Metabolic feeding of plants with photocaged trehalose-6-phosphate (Tre6P) can increase levels of the signaling metabolite Tre6P in the plant. Reprogramming of cellular metabolism by Tre6P stimulates a program of plant growth and enhanced crop yields, while boosting starch content. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Integrated Current Balancing Transformer for Primary Parallel Isolated Boost Converter

DEFF Research Database (Denmark)

Sen, Gökhan; Ouyang, Ziwei; Thomsen, Ole Cornelius

2011-01-01

A simple, PCB compatible integrated solution is proposed for the current balancing requirement of the primary parallel isolated boost converter (PPIBC). Input inductor and the current balancing transformer are merged into the same core, which reduces the number of components allowing a cheaper...

Boosting capacitive blue-energy and desalination devices with waste heat

NARCIS (Netherlands)

Janssen, Mathijs; Härtel, Andreas; Van Roij, René

2014-01-01

We show that sustainably harvesting "blue" energy from the spontaneous mixing process of fresh and salty water can be boosted by varying the water temperature during a capacitive mixing process. Our modified Poisson-Boltzmann calculations predict a strong temperature dependence of the electrostatic

Emerging concepts in dendrimer-based nanomedicine: from design principles to clinical applications.

Science.gov (United States)

Kannan, R M; Nance, E; Kannan, S; Tomalia, D A

2014-12-01

Dendrimers are discrete nanostructures/nanoparticles with 'onion skin-like' branched layers. Beginning with a core, these nanostructures grow in concentric layers to produce stepwise increases in size that are similar to the dimensions of many in vivo globular proteins. These branched tree-like concentric layers are referred to as 'generations'. The outer generation of each dendrimer presents a precise number of functional groups that may act as a monodispersed platform for engineering favourable nanoparticle-drug and nanoparticle-tissue interactions. These features have attracted significant attention in medicine as nanocarriers for traditional small drugs, proteins, DNA/RNA and in some instances as intrinsically active nanoscale drugs. Dendrimer-based drugs, as well as diagnostic and imaging agents, are emerging as promising candidates for many nanomedicine applications. First, we will provide a brief survey of recent nanomedicines that are either approved or in the clinical approval process. This will be followed by an introduction to a new 'nanoperiodic' concept which proposes nanoparticle structure control and the engineering of 'critical nanoscale design parameters' (CNDPs) as a strategy for optimizing pharmocokinetics, pharmocodynamics and site-specific targeting of disease. This paradigm has led to the emergence of CNDP-directed nanoperiodic property patterns relating nanoparticle behaviour to critical in vivo clinical translation issues such as cellular uptake, transport, elimination, biodistribution, accumulation and nanotoxicology. With a focus on dendrimers, these CNDP-directed nanoperiodic patterns are used as a strategy for designing and optimizing nanoparticles for a variety of drug delivery and imaging applications, including a recent dendrimer-based theranostic nanodevice for imaging and treating cancer. Several emerging preclinical dendrimer-based nanotherapy concepts related to inflammation, neuro-inflammatory disorders, oncology and infectious

Phase I Trial of Preoperative Hypofractionated Intensity-Modulated Radiotherapy with Incorporated Boost and Oral Capecitabine in Locally Advanced Rectal Cancer

International Nuclear Information System (INIS)

Freedman, Gary M.; Meropol, Neal J.; Sigurdson, Elin R.; Hoffman, John; Callahan, Elaine; Price, Robert; Cheng, Jonathan; Cohen, Steve; Lewis, Nancy; Watkins-Bruner, Deborah; Rogatko, Andre; Konski, Andre

2007-01-01

Purpose: To determine the safety and efficacy of preoperative hypofractionated radiotherapy using intensity-modulated radiotherapy (IMRT) and an incorporated boost with concurrent capecitabine in patients with locally advanced rectal cancer. Methods and Materials: The eligibility criteria included adenocarcinoma of the rectum, T3-T4 and/or N1-N2 disease, performance status 0 or 1, and age ≥18 years. Photon IMRT and an incorporated boost were used to treat the whole pelvis to 45 Gy and the gross tumor volume plus 2 cm to 55 Gy in 25 treatments within 5 weeks. The study was designed to escalate the dose to the gross tumor volume in 5-Gy increments in 3-patient cohorts. Capecitabine was given orally 825 mg/m 2 twice daily for 7 days each week during RT. The primary endpoint was the maximal tolerated radiation dose, and the secondary endpoints were the pathologic response and quality of life. Results: Eight patients completed RT at the initial dose level of 55 Gy. The study was discontinued because of toxicity-six Grade 3 toxicities occurred in 3 (38%) of 8 patients. All patients went on to definitive surgical resection, and no patient had a pathologically complete response. Conclusion: This regimen, using hypofractionated RT with an incorporated boost, had unacceptable toxicity despite using standard doses of capecitabine and IMRT. Additional research is needed to determine whether IMRT is able to reduce the side effects during and after pelvic RT with conventional dose fractionation

Innovative architecture design for high performance organic and hybrid multi-junction solar cells

Science.gov (United States)

Li, Ning; Spyropoulos, George D.; Brabec, Christoph J.

2017-08-01

The multi-junction concept is especially attractive for the photovoltaic (PV) research community owing to its potential to overcome the Schockley-Queisser limit of single-junction solar cells. Tremendous research interests are now focused on the development of high-performance absorbers and novel device architectures for emerging PV technologies, such as organic and perovskite PVs. It has been predicted that the multi-junction concept is able to boost the organic and perovskite PV technologies approaching the 20% and 30% benchmarks, respectively, showing a bright future of commercialization of the emerging PV technologies. In this contribution, we will demonstrate innovative architecture design for solution-processed, highly functional organic and hybrid multi-junction solar cells. A simple but elegant approach to fabricating organic and hybrid multi-junction solar cells will be introduced. By laminating single organic/hybrid solar cells together through an intermediate layer, the manufacturing cost and complexity of large-scale multi-junction solar cells can be significantly reduced. This smart approach to balancing the photocurrents as well as open circuit voltages in multi-junction solar cells will be demonstrated and discussed in detail.

Advanced Emergency Braking Controller Design for Pedestrian Protection Oriented Automotive Collision Avoidance System

Directory of Open Access Journals (Sweden)

Guo Lie

2014-01-01

Full Text Available Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian.

Advanced emergency braking controller design for pedestrian protection oriented automotive collision avoidance system.

Science.gov (United States)

Lie, Guo; Zejian, Ren; Pingshu, Ge; Jing, Chang

2014-01-01

Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian.

Intraoperative HDR implant boost for breast cancer (preliminary results)

International Nuclear Information System (INIS)

Rodriguez, I.; Torre, M. de la; Gonzalez, E.; Bourel, V.

1996-01-01

Introduction: In spite of the fact that it is been discussed whether or not a boost is necessary for all conservative treated breast cancer patients, it is a generalized radiotherapy practice. Since september 1993 we developed a breast conservative protocol for early stage breast cancer (T1-T2) with intraoperative HDR implant boost. Side effects, cosmetic results and recurrence rates are reviewed. Method and Material: From September 1993 we treated 55 patients with intraoperative HDR implant boost to the lumpectomy site for clinical T1 or T2 invasive breast cancer, followed by external megavoltage radiotherapy to the entire breast. We used the Nucletron microselectron HDR remote afterloading system with flexible implant tubes. The geometric distribution of the tubes was performed according to the 'Paris' configuration. Each implant was evaluated by calculating the dose-volume natural histograms. The HDR fractionation schedule consists of three fractions of 4.5Gy each given at least 48 hs apart, and starting between 48-72hs from surgical procedure. The external radiotherapy to the entire breast started one week after the completion of brachytherapy, using conventional fractionation of 5 fractions per week, 1,8Gy per fraction up to 45-50Gy. Results: So far there is not any local recurrence, but medium follow up is only 18 months. We did not observe any acute damage and the cosmetic outcome was 60% excellent, 30% good and 10% acceptable. Two patients developed localized fibrosis, in both the implant involved the submamary fold. Conclusion: The intraoperative implant is the most accurate way to localize the lumpectomy site, to define the target volume, decrease the total treatment time and avoid a second anesthetic procedure without delaying the inpatient time or the initial wound healing process

Boosting food security in sub-Saharan Africa through cassava ...

African Journals Online (AJOL)

Boosting food security in sub-Saharan Africa through cassava production: a case study of Nigeria. ... Nigerian Journal of Economic History ... The paper argues that cassava which is widely grown in Sub-Saharan Africa with a lot of variety of food derivatives from it can reduce to the barest minimum the present state of food ...

Comparison of three boosting methods in parent-offspring trios for genotype imputation using simulation study

Directory of Open Access Journals (Sweden)

Abbas Mikhchi

2016-01-01

Full Text Available Abstract Background Genotype imputation is an important process of predicting unknown genotypes, which uses reference population with dense genotypes to predict missing genotypes for both human and animal genetic variations at a low cost. Machine learning methods specially boosting methods have been used in genetic studies to explore the underlying genetic profile of disease and build models capable of predicting missing values of a marker. Methods In this study strategies and factors affecting the imputation accuracy of parent-offspring trios compared from lower-density SNP panels (5 K to high density (10 K SNP panel using three different Boosting methods namely TotalBoost (TB, LogitBoost (LB and AdaBoost (AB. The methods employed using simulated data to impute the un-typed SNPs in parent-offspring trios. Four different datasets of G1 (100 trios with 5 k SNPs, G2 (100 trios with 10 k SNPs, G3 (500 trios with 5 k SNPs, and G4 (500 trio with 10 k SNPs were simulated. In four datasets all parents were genotyped completely, and offspring genotyped with a lower density panel. Results Comparison of the three methods for imputation showed that the LB outperformed AB and TB for imputation accuracy. The time of computation were different between methods. The AB was the fastest algorithm. The higher SNP densities resulted the increase of the accuracy of imputation. Larger trios (i.e. 500 was better for performance of LB and TB. Conclusions The conclusion is that the three methods do well in terms of imputation accuracy also the dense chip is recommended for imputation of parent-offspring trios.

Experimental verification of internal parameter in magnetically coupled boost used as PV optimizer in parallel association

Science.gov (United States)

Sawicki, Jean-Paul; Saint-Eve, Frédéric; Petit, Pierre; Aillerie, Michel

2017-02-01

This paper presents results of experiments aimed to verify a formula able to compute duty cycle in the case of pulse width modulation control for a DC-DC converter designed and realized in laboratory. This converter, called Magnetically Coupled Boost (MCB) is sized to step up only one photovoltaic module voltage to supply directly grid inverters. Duty cycle formula will be checked in a first time by identifying internal parameter, auto-transformer ratio, and in a second time by checking stability of operating point on the side of photovoltaic module. Thinking on nature of generator source and load connected to converter leads to imagine additional experiments to decide if auto-transformer ratio parameter could be used with fixed value or on the contrary with adaptive value. Effects of load variations on converter behavior or impact of possible shading on photovoltaic module are also mentioned, with aim to design robust control laws, in the case of parallel association, designed to compensate unwanted effects due to output voltage coupling.

EORTC 22972-26991/MRC BR10 trial: Fractionated stereotactic boost following conventional radiotherapy of high grade gliomas

International Nuclear Information System (INIS)

Baumert, Brigitta G.; Brada, Michael; Bernier, Jacques; Kortmann, Rolf D.; Dehing-Oberije, Cary; Collette, Laurence; Davis, J. Bernard

2008-01-01

Background and purpose: The EORTC trial No. 22972 investigated the role of an additional fractionated stereotactic boost (fSRT) to conventional radiotherapy for patients with high grade gliomas. A quality-assurance (QA) programme was run in conjunction with the study and was the first within the EORTC addressing the quality of a supposedly highly accurate treatment technique such as stereotactic radiotherapy. A second aim was to investigate a possible relation between the clinical results of the stereotactic boost arm and the results of the QA. Materials and methods: The trial was closed in 2001 due to low accrual. In total, 25 patients were randomized: 14 into the experimental arm and 11 into the control arm. Six centres randomized patients, 8 centres had completed the dummy run (DR) for the stereotactic boost part. All participating centres (9) were asked to complete a quality-assurance questionnaire. The DR consisted of treatment planning according to the guidelines of the protocol on 3 different tumour volumes drawn on CT images of a humanized phantom. The SRT technique to be used was evaluated by the questionnaire. Clinical data from patients recruited to the boost arm from 6 participating centres were analysed. Results: There was a full compliance to the protocol requirements for 5 centres. Major and minor deviations in conformality were observed for 2 and 3 centres, respectively. Of the 8 centres which completed the DR, one centre did not comply with the requirements of stereotactic radiotherapy concerning accuracy, dosimetry and planning. Median follow-up and median overall survival were 39.2 and 21.4 months, respectively. Acute and late toxicities of the stereotactic boost were low. One radiation necrosis was seen for a patient who has not received the SRT boost. Three reported serious adverse events were all seizures and probably therapy-related. Conclusions: Overall compliance was good but not ideal from the point of view of this highly precise radiation

Hospitality industry veteran to lead workshop on boosting sales and business

OpenAIRE

Crumbley, Liz

2009-01-01

Hospitality industry expert Howard Feiertag will teach participants how to energize sales and boost business during the "Hospitality Sales" workshop, April 27 and 28 at the Hotel Roanoke and Conference Center in Roanoke, Va.

Emergency response network design for hazardous materials transportation with uncertain demand

Directory of Open Access Journals (Sweden)

Kamran Shahanaghi

2012-10-01

Full Text Available Transportation of hazardous materials play an essential role on keeping a friendly environment. Every day, a substantial amount of hazardous materials (hazmats, such as flammable liquids and poisonous gases, need to be transferred prior to consumption or disposal. Such transportation may result in unsuitable events for people and environment. Emergency response network is designed for this reason where specialist responding teams resolve any issue as quickly as possible. This study proposes a new multi-objective model to locate emergency response centers for transporting the hazardous materials. Since many real-world applications are faced with uncertainty in input parameters, the proposed model of this paper also assumes that reference and demand to such centre is subject to uncertainty, where demand is fuzzy random. The resulted problem formulation is modelled as nonlinear non-convex mixed integer programming and we used NSGAII method to solve the resulted problem. The performance of the proposed model is examined with several examples using various probability distribution and they are compared with the performance of other existing method.

Imputing data that are missing at high rates using a boosting algorithm

Energy Technology Data Exchange (ETDEWEB)

Cauthen, Katherine Regina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lambert, Gregory [Apple Inc., Cupertino, CA (United States); Ray, Jaideep [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Lefantzi, Sophia [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2016-09-01

Traditional multiple imputation approaches may perform poorly for datasets with high rates of missingness unless many m imputations are used. This paper implements an alternative machine learning-based approach to imputing data that are missing at high rates. Here, we use boosting to create a strong learner from a weak learner fitted to a dataset missing many observations. This approach may be applied to a variety of types of learners (models). The approach is demonstrated by application to a spatiotemporal dataset for predicting dengue outbreaks in India from meteorological covariates. A Bayesian spatiotemporal CAR model is boosted to produce imputations, and the overall RMSE from a k-fold cross-validation is used to assess imputation accuracy.

Search for new resonances with boosted signatures at CMS

CERN Multimedia

CERN. Geneva

2015-01-01

The LHC and its experiments are ideally suited to search for these new resonances in order to validate or constrain the corresponding theories. At resonance masses well above 1 TeV, these searches face specific challenges. The decay products have large Lorentz boosts, resulting in very collimated final state topologies. Jet substructure methods and the use of non-isolate...

Boosting iterative stochastic ensemble method for nonlinear calibration of subsurface flow models

KAUST Repository

Elsheikh, Ahmed H.

2013-06-01

A novel parameter estimation algorithm is proposed. The inverse problem is formulated as a sequential data integration problem in which Gaussian process regression (GPR) is used to integrate the prior knowledge (static data). The search space is further parameterized using Karhunen-Loève expansion to build a set of basis functions that spans the search space. Optimal weights of the reduced basis functions are estimated by an iterative stochastic ensemble method (ISEM). ISEM employs directional derivatives within a Gauss-Newton iteration for efficient gradient estimation. The resulting update equation relies on the inverse of the output covariance matrix which is rank deficient.In the proposed algorithm we use an iterative regularization based on the ℓ2 Boosting algorithm. ℓ2 Boosting iteratively fits the residual and the amount of regularization is controlled by the number of iterations. A termination criteria based on Akaike information criterion (AIC) is utilized. This regularization method is very attractive in terms of performance and simplicity of implementation. The proposed algorithm combining ISEM and ℓ2 Boosting is evaluated on several nonlinear subsurface flow parameter estimation problems. The efficiency of the proposed algorithm is demonstrated by the small size of utilized ensembles and in terms of error convergence rates. © 2013 Elsevier B.V.

Emerging experimental and computational technologies for purpose designed engineering of photosynthetic prokaryotes

KAUST Repository

Lindblad, Peter

2016-01-25

With recent advances in synthetic molecular tools to be used in photosynthetic prokaryotes, like cyanobacteria, it is possible to custom design and construct microbial cells for specific metabolic functions. This cross-disciplinary area of research has emerged within the interfaces of advanced genetic engineering, computational science, and molecular biotechnology. We have initiated the development of a genetic toolbox, using a synthetic biology approach, to custom design, engineer and construct cyanobacteria for selected function and metabolism. One major bottleneck is a controlled transcription and translation of introduced genetic constructs. An additional major issue is genetic stability. I will present and discuss recent progress in our development of genetic tools for advanced cyanobacterial biotechnology. Progress on understanding the electron pathways in native and engineered cyanobacterial enzymes and heterologous expression of non-native enymzes in cyanobacterial cells will be highlighted. Finally, I will discuss our attempts to merge synthetic biology with synthetic chemistry to explore fundamantal questions of protein design and function.

Comparison of IPV to tOPV week 39 boost of primary OPV vaccination in Indian infants: an open labelled randomized controlled trial

Directory of Open Access Journals (Sweden)

Suman Kanungo

2017-01-01

Conclusions: This study indicates that an IPV boost at week 39 is equivalent to tOPV in intestinal immunity, and provides higher seroconversion compared to tOPV. The major limitation of the study was the additional OPV doses receive by infants during pulse polio immunization resulted in additional mucosal boosting, diminishing the impact of IPV or tOPV boost at week 39. However, IPV for OPV boost should prove to be a step forward in the global polio eradication initiative to reduce the problem of circulating vaccine-derived poliovirus (cVDPV.

Individualized planning target volumes for intrafraction motion during hypofractionated intensity-modulated radiotherapy boost for prostate cancer

International Nuclear Information System (INIS)

Cheung, Patrick; Sixel, Katharina; Morton, Gerard; Loblaw, D. Andrew; Tirona, Romeo; Pang, Geordi; Choo, Richard; Szumacher, Ewa; DeBoer, Gerrit; Pignol, Jean-Philippe

2005-01-01

Purpose: The objective of the study was to access toxicities of delivering a hypofractionated intensity-modulated radiotherapy (IMRT) boost with individualized intrafraction planning target volume (PTV) margins and daily online correction for prostate position. Methods and materials: Phase I involved delivering 42 Gy in 21 fractions using three-dimensional conformal radiotherapy, followed by a Phase II IMRT boost of 30 Gy in 10 fractions. Digital fluoroscopy was used to measure respiratory-induced motion of implanted fiducial markers within the prostate. Electronic portal images were taken of fiducial marker positions before and after each fraction of radiotherapy during the first 9 days of treatment to calculate intrafraction motion. A uniform 10-mm PTV margin was used for the first phase of treatment. PTV margins for Phase II were patient-specific and were calculated from the respiratory and intrafraction motion data obtained from Phase I. The IMRT boost was delivered with daily online correction of fiducial marker position. Acute toxicity was measured using National Cancer Institute Common Toxicity Criteria, version 2.0. Results: In 33 patients who had completed treatment, the average PTV margin used during the hypofractionated IMRT boost was 3 mm in the lateral direction, 3 mm in the superior-inferior direction, and 4 mm in the anteroposterior direction. No patients developed acute Grade 3 rectal toxicity. Three patients developed acute Grade 3 urinary frequency and urgency. Conclusions: PTV margins can be reduced significantly with daily online correction of prostate position. Delivering a hypofractionated boost with this high-precision IMRT technique resulted in acceptable acute toxicity

ATLAS Jet Reconstruction, Calibration, and Tagging of Lorentz-boosted Objects

CERN Document Server

Schramm, Steven; The ATLAS collaboration

2017-01-01

Jet reconstruction in the ATLAS detector takes multiple forms, as motivated by the intended usage of the jet. Different jet definitions are used in particular for the study of QCD jets and jets containing the hadronic decay of boosted massive particles. These different types of jets are calibrated through a series of mostly sequential steps, providing excellent uncertainties, including a first in situ calibration of the jet mass scale. Jet tagging is investigated, including both not-top-quark vs gluon discrimination as well as W/Z boson, H$\\to$bb, and top-quark identification. This includes a first look at the use of Boosted Decision Trees and Deep Neural Networks built from jet substructure variables, as well as Convolutional Neural Networks built from jet images. In all cases, these advanced techniques are seen to provide gains over the standard approaches, with the magnitude of the gain depending on the use case. Future methods for improving jet tagging are briefly discussed, including jet substructure-ori...

Boosting the Direct CP Measurement of the Higgs-Top Coupling.

Science.gov (United States)

Buckley, Matthew R; Gonçalves, Dorival

2016-03-04

Characterizing the 125 GeV Higgs boson is a critical component of the physics program at the LHC Run II. In this Letter, we consider tt[over ¯]H associated production in the dileptonic mode. We demonstrate that the difference in azimuthal angle between the leptons from top decays can directly reveal the CP structure of the top-Higgs coupling with the sensitivity of the measurement substantially enhanced in the boosted Higgs regime. We first show how to access this channel via H→bb[over ¯] jet-substructure tagging, then demonstrate the ability of the new variable to measure CP. Our analysis includes all signal and background samples simulated via the MC@NLO algorithm including hadronization and underlying-event effects. Using a boosted Higgs substructure with dileptonic tops, we find that the top-Higgs coupling strength and the CP structure can be directly probed with achievable luminosity at the 13 TeV LHC.

Comparison of posterior fossa and tumor bed boost in medulloblastoma.

Science.gov (United States)

Paulino, A C; Saw, C B; Wen, B C

2000-10-01

To quantify the difference between the area of brain irradiated using the posterior fossa boost (PFB) and tumor bed boost (TBB) in medulloblastoma, we studied 15 simulation radiographs of patients treated in our institution from 1990 and 1999. The PFB was compared with the TBB, which was defined as the tumor bed plus 2-cm margin as demonstrated by postoperative magnetic resonance imaging. The PFB field treated a mean area of 9.43 cm2 more brain than the TBB. In 3 patients (20%), the area of the brain in the TBB was larger than the PFB. In 11 patients (73.3%), the PFB field had more than 10% more brain than the TBB. The cochlea was in the PFB and TBB field in all patients. In more than two thirds of patients, the area of brain irradiated with the PFB was at least 10% greater than the TBB. Future studies are needed to determine whether the TBB can replace the PFB in patients with medulloblastoma.

Design and operation of the emergency support center, CAE

International Nuclear Information System (INIS)

Caro, R. J.; Lopez Trillo, E.

2016-01-01

The enhancements developed in Spain in the area of Emergency Management, as consequence of the accident at the Fukushima Dai-Ichi NPP in 2011, included the definition of new emergency response centers; Alternative Center for Emergency Management (CAGE) on each NPP and the Emergency Support Center (CAE), shared by all NPPs. This article summarizes the main features and operation activities undertaken since the establishment of the new CAE, centralized, external to the NPPs shared by all Spanish plants and managed by Tecnatom. (Author)

Results of brachytherapy boost in high risk breast cancer patients

International Nuclear Information System (INIS)

Battermann, J.J.

1996-01-01

Introduction: in breast conserving therapy the role of brachytherapy as a boost after whole breast irradiation is not clear. The series from the Netherlands Cancer Institute show a very high local control rate, but the question could be raised whether all these patients need a brachy boost. Therefore, it was decided at our institute, to deliver a brachy boost only to high risk patients, viz. patients with incomplete resection margins and/or extensive in situ cancer (ECI). Materials and methods: in the period 1988 through 1993 a total of 148 patients with 151 breast tumours received a boost on the tumour bed using brachytherapy. Age varied from 25 till 74 years, with a mean age of 52.3 years. Incomplete resection margins were found in 60 patients, ECI in 31 and both in 49 patients. In the majority of patients, the ECI component was not completely removed. T-stage was unknown in 9 patients. T1 in 83, T2 in 49 and T3 in 10. Nodal status was N0 in 119 and N1 in 33 patients. Infiltrating duct carcinoma was the most common histology. No infiltrating growth was found in 6 patients, but one patient presented a positive node. The interval period between day of operation and day of brachytherapy implantation was between 3 and 4 months in 62%. The mean interval between completion of beam irradiation and day of implantation was 18 days, while 12 patients received their brachytherapy previous to the beam irradiation. External irradiation was with two tangential fields and a total dose of 50 Gy in 25 fractions over 6 weeks (9 fractions in two weeks). The number of needles in two planes. Most patients were implanted under local anaesthesia. Dose rate in 97 patients was 51 - 60 cGy/h. Results: follow-up for patients alive varied from 2 years till 7 years with a mean follow-up period of 4 years. One hundred and twenty five patients are alive, including 6 patients with manifest metastases. Local recurrence was encountered in 8 patients (interval 14 - 60 months, mean 30 months), with

Interstitial high-dose rate brachytherapy as boost for anal canal cancer

International Nuclear Information System (INIS)

Falk, Alexander Tuan; Claren, Audrey; Benezery, Karen; François, Eric; Gautier, Mathieu; Gerard, Jean-Pierre; Hannoun-Levi, Jean-Michel

2014-01-01

To assess clinical outcomes of patients treated with a high-dose rate brachytherapy boost for anal canal cancer (ACC). From August 2005 to February 2013, 28 patients presenting an ACC treated by split-course external beam radiotherapy (EBRT) and HDR brachytherapy with or without chemotherapy in a French regional cancer center in Nice were retrospectively analyzed. Median age was 60.6 years [34 – 83], 25 patients presented a squamous cell carcinoma and 3 an adenocarcinoma; 21 received chemotherapy. Median dose of EBRT was 45 Gy [43.2 – 52]. Median dose of HDR brachytherapy was 12 Gy [10 - 15] with a median duration of 2 days. Median overall treatment time was 63 days and median delay between EBRT and brachytherapy was 20 days. Two-year local relapse free, metastatic free, disease free and overall survivals were 83%, 81.9%, 71.8% and 87.7% respectively. Acute toxicities were frequent but not severe with mostly grade 1 toxicities: 37% of genito-urinary, 40.7% of gastro-intestinal and 3.7% of cutaneous toxicities. Late toxicities were mainly G1 (43.1%) and G2 (22%). Two-year colostomy-free survival was 75.1%, one patient had a definitive sphincter amputation. High-dose rate brachytherapy for anal canal carcinoma as boost represents a feasible technique compared to low or pulsed-dose rate brachytherapy. This technique remains an excellent approach to precisely boost the tumor in reducing the overall treatment time

Development of a Online Nuclear Emergency Response System (ONERS) for Kalpakkam site - the design aspects

Energy Technology Data Exchange (ETDEWEB)

Raja Shekhar, S. S.; Bhatawadekar, Shantanu; Krishna Murthy, Y. V.N., [Regional Remote Sensing Service Centre, Department of Space, Nagpur (India); Srinivas, C. V.; Venkatesan, [Radiological Safety Division, Radiological Safety and Environmental Group, Indira Gandhi Centre for Atomic Research, Kalapakkam (India)

2012-07-01

An Online Nuclear Emergency Response System (ONERS) is developed for the nuclear power plant site at Kalpakkam as part of the Department of Atomic Energy (DAE) initiative. ONERS is a GIS based spatial analysis system designed indigenously to provide decision support in the event of a radioactive leak or accident from any of the nuclear facilities by assessing the dispersion and deposition patterns of the atmospheric releases, integrate with spatial geographical database for impact assessment and guidance for mitigation. The system is designed with open software tools (UMN Map server, MYSQL, PHP, Java scripts) and its main features include assessment of dose, short and long term forecast, counter measure support, impact assessment to minimize potential threat to man and environment during radiological emergencies. The system is implemented in live mode with integration of numerical models and spatial data base for the site region and is presently operational for the Kalpakkam site. (author)

Development of a Online Nuclear Emergency Response System (ONERS) for Kalpakkam site - the design aspects

International Nuclear Information System (INIS)

Raja Shekhar, S.S.; Bhatawadekar, Shantanu; Krishna Murthy, Y.V.N.; Srinivas, C.V.; Venkatesan

2012-01-01

An Online Nuclear Emergency Response System (ONERS) is developed for the nuclear power plant site at Kalpakkam as part of the Department of Atomic Energy (DAE) initiative. ONERS is a GIS based spatial analysis system designed indigenously to provide decision support in the event of a radioactive leak or accident from any of the nuclear facilities by assessing the dispersion and deposition patterns of the atmospheric releases, integrate with spatial geographical database for impact assessment and guidance for mitigation. The system is designed with open software tools (UMN Map server, MYSQL, PHP, Java scripts) and its main features include assessment of dose, short and long term forecast, counter measure support, impact assessment to minimize potential threat to man and environment during radiological emergencies. The system is implemented in live mode with integration of numerical models and spatial data base for the site region and is presently operational for the Kalpakkam site. (author)

Combining Boosted Global

Directory of Open Access Journals (Sweden)

Szidónia Lefkovits

2011-06-01

Full Text Available The domain of object detection presents a wide range of interest due to its numerous application possibilities especially real time applications. All of them require high detection rate correlated with short processing time. One of the most efficient systems, working with visual information, were presented in the publication of Viola et al. [1], [2].This detection system uses classifiers based on Haar-like separating features combined with the AdaBoost learning algorithm. The most important bottleneck of the system is the big number of false detections at high hit rate. In this paper we propose to overcome this disadvantage by using specialized parts classifiers. This aim comes from the observation that the target object does not resemble the false detections at all.The reason of this fact is the coding manner of Haar-like features which attend to handle image patches and neglect the edges and contours. In order to obtain a more robust classifier, a global aspect method is combined with a part-based method, having the goal to improve the performance of the detector without significant increase of the detection time.

A mechanism for proven technology foresight for emerging fast reactor designs and concepts

International Nuclear Information System (INIS)

Anuar, Nuraslinda; Muhamad Pauzi, Anas

2016-01-01

The assessment of emerging nuclear fast reactor designs and concepts viability requires a combination of foresight methods. A mechanism that allows for the comparison and quantification of the possibility of being a proven technology in the future, β for the existing fast reactor designs and concepts is proposed as one of the quantitative foresight method. The methodology starts with the identification at the national or regional level, of the factors that would affect β. The factors are then categorized into several groups; economic, social and technology elements. Each of the elements is proposed to be mathematically modelled before all of the elemental models can be combined. Once the overall β model is obtained, the β min is determined to benchmark the acceptance as a candidate design or concept. The β values for all the available designs and concepts are then determined and compared with the β min , resulting in a list of candidate designs that possess the β value that is larger than the β min . The proposed methodology can also be applied to purposes other than technological foresight

A mechanism for proven technology foresight for emerging fast reactor designs and concepts

Energy Technology Data Exchange (ETDEWEB)

Anuar, Nuraslinda, E-mail: nuraslinda@uniten.edu.my; Muhamad Pauzi, Anas, E-mail: anas@uniten.edu.my [College of Engineering, Universiti Tenaga Nasional, Jalan IKRAM-UNITEN, 43000 Kajang, Selangor (Malaysia)

2016-01-22

The assessment of emerging nuclear fast reactor designs and concepts viability requires a combination of foresight methods. A mechanism that allows for the comparison and quantification of the possibility of being a proven technology in the future, β for the existing fast reactor designs and concepts is proposed as one of the quantitative foresight method. The methodology starts with the identification at the national or regional level, of the factors that would affect β. The factors are then categorized into several groups; economic, social and technology elements. Each of the elements is proposed to be mathematically modelled before all of the elemental models can be combined. Once the overall β model is obtained, the β{sub min} is determined to benchmark the acceptance as a candidate design or concept. The β values for all the available designs and concepts are then determined and compared with the β{sub min}, resulting in a list of candidate designs that possess the β value that is larger than the β{sub min}. The proposed methodology can also be applied to purposes other than technological foresight.

A prediction model of short-term ionospheric foF2 Based on AdaBoost

Science.gov (United States)

Zhao, Xiukuan; Liu, Libo; Ning, Baiqi

Accurate specifications of spatial and temporal variations of the ionosphere during geomagnetic quiet and disturbed conditions are critical for applications, such as HF communications, satellite positioning and navigation, power grids, pipelines, etc. Therefore, developing empirical models to forecast the ionospheric perturbations is of high priority in real applications. The critical frequency of the F2 layer, foF2, is an important ionospheric parameter, especially for radio wave propagation applications. In this paper, the AdaBoost-BP algorithm is used to construct a new model to predict the critical frequency of the ionospheric F2-layer one hour ahead. Different indices were used to characterize ionospheric diurnal and seasonal variations and their dependence on solar and geomagnetic activity. These indices, together with the current observed foF2 value, were input into the prediction model and the foF2 value at one hour ahead was output. We analyzed twenty-two years’ foF2 data from nine ionosonde stations in the East-Asian sector in this work. The first eleven years’ data were used as a training dataset and the second eleven years’ data were used as a testing dataset. The results show that the performance of AdaBoost-BP is better than those of BP Neural Network (BPNN), Support Vector Regression (SVR) and the IRI model. For example, the AdaBoost-BP prediction absolute error of foF2 at Irkutsk station (a middle latitude station) is 0.32 MHz, which is better than 0.34 MHz from BPNN, 0.35 MHz from SVR and also significantly outperforms the IRI model whose absolute error is 0.64 MHz. Meanwhile, AdaBoost-BP prediction absolute error at Taipei station from the low latitude is 0.78 MHz, which is better than 0.81 MHz from BPNN, 0.81 MHz from SVR and 1.37 MHz from the IRI model. Finally, the variety characteristics of the AdaBoost-BP prediction error along with seasonal variation, solar activity and latitude variation were also discussed in the paper.

Intraoperative Boost Radiotherapy during Targeted Oncoplastic Breast Surgery: Overview and Single Center Experiences

Directory of Open Access Journals (Sweden)

Wolfram Malter

2014-01-01

Full Text Available Breast-conserving surgery followed by whole-breast irradiation is the standard local therapy for early breast cancer. The international discussion of reduced importance of wider tumor-free resection margins than “tumor not touching ink” leads to the development of five principles in targeted oncoplastic breast surgery. IORT improves local recurrence risk and diminishes toxicity since there is less irradiation of healthy tissue. Intraoperative radiotherapy (IORT can be delivered in two settings: an IORT boost followed by a conventional regimen of external beam radiotherapy or a single IORT dose. The data from TARGIT-A and ELIOT reinforce the conviction that intraoperative radiotherapy during breast-conserving surgery is a reliable alternative to conventional postoperative fractionated irradiation, but only in a carefully selected population at low risk of local recurrence. We describe our experiences with IORT boost (50 kV energy X-rays; 20 Gy in combination with targeted oncoplastic breast surgery in a routine clinical setting. Our experiences demonstrate the applicability and reliability of combining IORT boost with targeted oncoplastic breast surgery in breast-conserving therapy of early breast cancer.

Novel vehicle detection system based on stacked DoG kernel and AdaBoost

Science.gov (United States)

Kang, Hyun Ho; Lee, Seo Won; You, Sung Hyun

2018-01-01

This paper proposes a novel vehicle detection system that can overcome some limitations of typical vehicle detection systems using AdaBoost-based methods. The performance of the AdaBoost-based vehicle detection system is dependent on its training data. Thus, its performance decreases when the shape of a target differs from its training data, or the pattern of a preceding vehicle is not visible in the image due to the light conditions. A stacked Difference of Gaussian (DoG)–based feature extraction algorithm is proposed to address this issue by recognizing common characteristics, such as the shadow and rear wheels beneath vehicles—of vehicles under various conditions. The common characteristics of vehicles are extracted by applying the stacked DoG shaped kernel obtained from the 3D plot of an image through a convolution method and investigating only certain regions that have a similar patterns. A new vehicle detection system is constructed by combining the novel stacked DoG feature extraction algorithm with the AdaBoost method. Experiments are provided to demonstrate the effectiveness of the proposed vehicle detection system under different conditions. PMID:29513727

Maximum Power Point Tracking (MPPT Pada Sistem Pembangkit Listrik Tenaga Angin Menggunakan Buck-Boost Converter

Directory of Open Access Journals (Sweden)

Muhamad Otong

2017-05-01

Full Text Available In this paper, the implementation of the Maximum Power Point Tracking (MPPT technique is developed using buck-boost converter. Perturb and observe (P&O MPPT algorithm is used to searching maximum power from the wind power plant for charging of the battery. The model used in this study is the Variable Speed Wind Turbine (VSWT with a Permanent Magnet Synchronous Generator (PMSG. Analysis, design, and modeling of wind energy conversion system has done using MATLAB/simulink. The simulation results show that the proposed MPPT produce a higher output power than the system without MPPT. The average efficiency that can be achieved by the proposed system to transfer the maximum power into battery is 90.56%.

Optimal infrastructure selection to boost regional sustainable economy

OpenAIRE

Martín Utrillas, Manuel Guzmán; Juan-Garcia, F.; Cantó Perelló, Julián; Curiel Esparza, Jorge

2015-01-01

The role of infrastructures in boosting the economic growth of the regions is widely recognized. In many cases, an infrastructure is selected by subjective reasons. Selection of the optimal infrastructure for sustainable economic development of a region should be based on objective and founded reasons, not only economical, but also environmental and social. In this paper is developed such selection through a hybrid method based on Delphi, analytical hierarchy process (AHP), and VIKOR (from Se...

Actin Waves Do Not Boost Neurite Outgrowth in the Early Stages of Neuron Maturation

Directory of Open Access Journals (Sweden)

Simone Mortal

2017-12-01

Full Text Available During neurite development, Actin Waves (AWs emerge at the neurite base and move up to its tip, causing a transient retraction of the Growth Cone (GC. Many studies have shown that AWs are linked to outbursts of neurite growth and, therefore, contribute to the fast elongation of the nascent axon. Using long term live cell-imaging, we show that AWs do not boost neurite outgrowth and that neurites without AWs can elongate for several hundred microns. Inhibition of Myosin II abolishes the transient GC retraction and strongly modifies the AWs morphology. Super-resolution nanoscopy shows that Myosin IIB shapes the growth cone-like AWs structure and is differently distributed in AWs and GCs. Interestingly, depletion of membrane cholesterol and inhibition of Rho GTPases decrease AWs frequency and velocity. Our results indicate that Myosin IIB, membrane tension, and small Rho GTPases are important players in the regulation of the AW dynamics. Finally, we suggest a role for AWs in maintaining the GCs active during environmental exploration.

Dichroic subjettiness ratios to distinguish colour flows in boosted boson tagging

Energy Technology Data Exchange (ETDEWEB)

Salam, Gavin P. [CERN, Theoretical Physics Department,CH-1211, Geneva 23 (Switzerland); Schunk, Lais; Soyez, Gregory [IPhT, CEA Saclay, CNRS UMR 3681,F-91191 Gif-sur-Yvette cedex (France)

2017-03-06

N-subjettiness ratios are in wide use for tagging heavy boosted objects, in particular the ratio of 2-subjettiness to 1-subjettiness for tagging boosted electroweak bosons. In this article we introduce a new, dichroic ratio, which uses different regions of a jet to determine the two subjettiness measures, emphasising the hard substructure for the 1-subjettiness and the full colour radiation pattern for the 2-subjettiness. Relative to existing N-subjettiness ratios, the dichroic extension, combined with SoftDrop (pre-)grooming, makes it possible to increase the ultimate signal significance by about 25% (for 2 TeV jets), or to reduce non-perturbative effects by a factor of 2−3 at 50% signal efficiency while maintaining comparable background rejection. We motivate the dichroic approach through the study of Lund diagrams, supplemented with resummed analytical calculations.

Dichroic subjettiness ratios to distinguish colour flows in boosted boson tagging

International Nuclear Information System (INIS)

Salam, Gavin P.; Schunk, Lais; Soyez, Gregory

2017-01-01

N-subjettiness ratios are in wide use for tagging heavy boosted objects, in particular the ratio of 2-subjettiness to 1-subjettiness for tagging boosted electroweak bosons. In this article we introduce a new, dichroic ratio, which uses different regions of a jet to determine the two subjettiness measures, emphasising the hard substructure for the 1-subjettiness and the full colour radiation pattern for the 2-subjettiness. Relative to existing N-subjettiness ratios, the dichroic extension, combined with SoftDrop (pre-)grooming, makes it possible to increase the ultimate signal significance by about 25% (for 2 TeV jets), or to reduce non-perturbative effects by a factor of 2−3 at 50% signal efficiency while maintaining comparable background rejection. We motivate the dichroic approach through the study of Lund diagrams, supplemented with resummed analytical calculations.

Passive vs Active Knowledge Transfer: boosting grant proposal impact

DEFF Research Database (Denmark)

Grigorov, Ivo; Bayliss-Brown, Georgia; Murphy, David

2017-01-01

Research funders are increasingly concerned with measurable socio-economic impact of investment in research, and on increasingly shorter timescales. Innovation, and “open innovation” are the policy priorities of the moment and optimising the flow of ideas along the lab-2-market spectrum...... is essential for re-use of results, fuelling open innovation, and boosting socio-economic impact or public funded research....

Flavor Tagging with Track Jets in Boosted Topologies with the ATLAS Detector

CERN Document Server

The ATLAS collaboration

2014-01-01

The ability to resolve and b-tag heavy flavor jets produced from the decay of boosted heavy particles, such as top quarks or Higgs bosons, is vital for the identification of new physics signatures as the LHC moves to higher energies and luminosities in 2015. Within these complex environments, resolving the different decay products can be achieved by using jets with a smaller distance parameter R. We propose the use of small-R track jets for this purpose. Track jets allow for a flexible way to identify and tag b-hadron decays independently of calorimeter jet algorithms, thus providing a robust way to integrate b-tagging with non-regular jet algorithms (i.e. large-R groomed jets) optimized for boosted topologies.

Radiotherapy boost dose-escalation for invasive breast cancer after breast-conserving surgery: 2093 Patients treated with a prospective margin-directed policy

International Nuclear Information System (INIS)

Livi, Lorenzo; Meattini, Icro; Franceschini, Davide; Saieva, Calogero; Meacci, Fiammetta; Marrazzo, Livia; Gerlain, Elena; Desideri, Isacco; Scotti, Vieri; Nori, Jacopo; Sanchez, Luis Jose; Orzalesi, Lorenzo; Bonomo, Pierluigi; Greto, Daniela; Bianchi, Simonetta; Biti, Giampaolo

2013-01-01

Purpose: To investigate the outcome of invasive early breast cancer patients that underwent breast-conserving surgery and adjuvant radiotherapy (RT), treated with a prospective margin-directed institutional policy for RT boost dose, based on final margins status (FMS). Methods and materials: A total of 2093 patients were treated between 2000 and 2008. 10 Gy boost was prescribed in case of FMS > 5 mm; 16 Gy boost with FMS between 2 and 5 mm; 20 Gy boost in case of FMS 5 mm. At multivariate analysis, higher nuclear grade (p = 0.045), triple negative subtype (p = 0.036) and higher T-stage (p = 0.02) resulted as the independent predictors of LR occurrence. Conclusions: Our experience showed that a margin-directed policy of RT boost dose-escalation seems to reduce the negative impact of FMS on LR, but it is not able to overcome the unfavorable effect of higher nuclear grade, higher T stage and triple negative subtype

Modeling and Implementing Two-Stage AdaBoost for Real-Time Vehicle License Plate Detection

Directory of Open Access Journals (Sweden)

Moon Kyou Song

2014-01-01

Full Text Available License plate (LP detection is the most imperative part of the automatic LP recognition system. In previous years, different methods, techniques, and algorithms have been developed for LP detection (LPD systems. This paper proposes to automatical detection of car LPs via image processing techniques based on classifier or machine learning algorithms. In this paper, we propose a real-time and robust method for LPD systems using the two-stage adaptive boosting (AdaBoost algorithm combined with different image preprocessing techniques. Haar-like features are used to compute and select features from LP images. The AdaBoost algorithm is used to classify parts of an image within a search window by a trained strong classifier as either LP or non-LP. Adaptive thresholding is used for the image preprocessing method applied to those images that are of insufficient quality for LPD. This method is of a faster speed and higher accuracy than most of the existing methods used in LPD. Experimental results demonstrate that the average LPD rate is 98.38% and the computational time is approximately 49 ms.

LIBO - boosting medical cyclotron facilities for cancer therapy Exhibition LEPFest 2000

CERN Multimedia

2000-01-01

Length : Energy boost : From 62 to 200 MeVAccelerating gradient : 10 MeV/metreAccelerating frequency : 3 GHz Collaboration : CERN, INFN and University of Milan, INFN and University of Naples and TERA foundation Prototype test in 2001 : SC cyclotron Catania

Boosted searches for new physics at the LHC

International Nuclear Information System (INIS)

Schlaffer, Matthias J.

2015-09-01

During the first run of the LHC, no apparent signs of new physics beyond the Standard Model were discovered, but rather the Standard Model-like properties of the Higgs particle confirmed. Therefore, new and powerful methods are needed to disclose the traces of new physics, which is expected to be at the TeV scale in order to solve the hierarchy problem. In this thesis, we propose two complementary strategies for the quest for new physics at the LHC. First, we show how a very boosted Higgs in association with a hard jet can be used to determine the important top Yukawa coupling in gluon fusion. In the inclusive gluon fusion process this is not feasible since possible deviations from its Standard Model value are combined and can even cancel with the effective Higgs-gluon interaction mediated by new top partners. This cancellation is motivated within minimal composite Higgs models but also in certain regions of the MSSM parameter space and can lead to a Standard Model-like inclusive cross section that allows no conclusions on the mass spectrum of the new physics. We work out in detail how this degeneracy can be broken in the boosted Higgs channel and find that even in the worst case scenario with a Standard Model-like inclusive cross section, the top Yukawa coupling can be constrained to 0.8-1.3 times its Standard Model value at 95% CL with an integrated luminosity of 3 000 fb -1 . The second strategy is targeted at direct stop and sbottom searches in the fully hadronic top decay channel. Since the stop, sbottom and neutralino masses are unknown, very different event shapes are imaginable, ranging from unboosted top quarks and low missing energy to highly boosted top quarks and large missing energy in the final state. In order to cover a wide range of possible event shapes and consequently stop, sbottom, and neutralino masses, we combine several top taggers based on jet substructure techniques to obtain a scale invariant search strategy. The performance of this

Analysis and Control of Buck-Boost Converter with the Same Input Polarity Based on Novel Energy Factor Evaluation

Directory of Open Access Journals (Sweden)

Mahmoud Shaker Nasr

2017-03-01

Full Text Available This paper presents firstly a buck-boost circuit with the advantage that its output voltage polarity is the same as the input polarity. The circuit operation is presented and analyzed in different modes of operation. The well known parameters used in evaluation of DC/DC converters like Total Harmonic Distortion THD, Power Factor PF, and Ripple Factor RF have no meaning in DC/DC converters, so it is to introduce efficient concepts to permit a fair evaluation of the converter. This paper present other parameters that can be used to study the characteristics of the converter and gives a real and logic means of its operation. These main parameters are: pumping energy PE, storage energy SE, energy factor EF, and energy losses EL. In addition, the converter efficiency is not considered as 100 % as taken in most analyzing studies. The positive DC/DC buck-boost converter is evaluated according to the new concepts and the system model is deduced for different cases of operation taking into account the resistance of the circuit inductor. The circuit is implemented practically and the presented obtained results show the correct operation under different modes of operation. In addition the control design of the converter is built such that a PI controller with windup is considered. In order to test the effectiveness of the designed control algorithm, the system were exposed to different voltage reference values and the obtained results demonstrate that the system responses for all cases are very acceptable according to the criteria of the control system theory.

Design and implementation of reliability data system of emergency diesel generator for YGN 3,4

International Nuclear Information System (INIS)

Kim, S. H.; Jang, S. D.; Kim, G. Y.; Kim, T. W.; Kim, Y. H.; Jeong, H. J.; Choi, G. H.

1998-01-01

This paper describes the design and implementation of D 2 REAMS that supports management and monitoring of the reliability data of emergency diesel generator of YGN 3,4 nuclear power plant. D2REAMS is the computerized reliability database management system to control the reliability of the emergency diesel generator of nuclear power plant and consists of seven sub-modules. Also, it was developed with intranet technology to eliminate the common problems of conventional client-server architecture. As the result of this implementation, the reliability and unavailability can be automatically computed by D2REAMS with the stored test and operation data of YGN 3,4 nuclear power plant

Quality of Life in Women Undergoing Breast Irradiation in a Randomized, Controlled Clinical Trial Evaluating Different Tumor Bed Boost Fractionations

International Nuclear Information System (INIS)

Finkel, Morgan A.; Cooper, Benjamin T.; Li, Xiaochun; Fenton-Kerimian, Maria; Goldberg, Judith D.; Formenti, Silvia C.

2016-01-01

Purpose: To identify differences in breast cancer patient-reported quality of life (QOL) between 2 radiation tumor bed boost dose regimens. Methods and Materials: Four hundred patients with stage 0, I, or II breast cancer who underwent segmental mastectomy with sentinel node biopsy and/or axillary node dissection were treated with either a daily or weekly boost. Patients were treated prone to 40.5 Gy/15 fractions to the whole breast, 5 days per week. Patients were randomized to a concomitant daily boost to the tumor bed of 0.5 Gy, or a weekly boost of 2 Gy on Friday. Patients completed 6 validated QOL survey instruments at baseline, last week of treatment (3 weeks), 45-60 days from the completion of radiation treatment, and at 2-year follow-up. Results: There were no statistically significance differences in responses to the 6 QOL instruments between the daily and weekly radiation boost regimens, even after adjustment for important covariates. However, several changes in responses over time occurred in both arms, including worsening functional status, cosmetic status, and breast-specific pain at the end of treatment as compared with before and 45 to 60 days after the conclusion of treatment. Conclusions: Whole-breast, prone intensity modulated radiation has similar outcomes in QOL measures whether given with a daily or weekly boost. This trial has generated the foundation for a current study of weekly versus daily radiation boost in women with early breast cancer in which 3-dimensional conformal radiation is allowed as a prospective stratification factor.

Quality of Life in Women Undergoing Breast Irradiation in a Randomized, Controlled Clinical Trial Evaluating Different Tumor Bed Boost Fractionations

Energy Technology Data Exchange (ETDEWEB)

Finkel, Morgan A.; Cooper, Benjamin T. [Department of Radiation Oncology, New York University School of Medicine, New York, New York (United States); Li, Xiaochun [Division of Biostatistics, Departments of Population Health and Environmental Medicine, New York University School of Medicine, New York, New York (United States); Fenton-Kerimian, Maria [Department of Radiation Oncology, New York University School of Medicine, New York, New York (United States); Goldberg, Judith D. [Division of Biostatistics, Departments of Population Health and Environmental Medicine, New York University School of Medicine, New York, New York (United States); Formenti, Silvia C., E-mail: formenti@med.cornell.edu [Department of Radiation Oncology, New York University School of Medicine, New York, New York (United States)

2016-06-01

Purpose: To identify differences in breast cancer patient-reported quality of life (QOL) between 2 radiation tumor bed boost dose regimens. Methods and Materials: Four hundred patients with stage 0, I, or II breast cancer who underwent segmental mastectomy with sentinel node biopsy and/or axillary node dissection were treated with either a daily or weekly boost. Patients were treated prone to 40.5 Gy/15 fractions to the whole breast, 5 days per week. Patients were randomized to a concomitant daily boost to the tumor bed of 0.5 Gy, or a weekly boost of 2 Gy on Friday. Patients completed 6 validated QOL survey instruments at baseline, last week of treatment (3 weeks), 45-60 days from the completion of radiation treatment, and at 2-year follow-up. Results: There were no statistically significance differences in responses to the 6 QOL instruments between the daily and weekly radiation boost regimens, even after adjustment for important covariates. However, several changes in responses over time occurred in both arms, including worsening functional status, cosmetic status, and breast-specific pain at the end of treatment as compared with before and 45 to 60 days after the conclusion of treatment. Conclusions: Whole-breast, prone intensity modulated radiation has similar outcomes in QOL measures whether given with a daily or weekly boost. This trial has generated the foundation for a current study of weekly versus daily radiation boost in women with early breast cancer in which 3-dimensional conformal radiation is allowed as a prospective stratification factor.