Magnetic study of superconductivity in YBa2Cu3O7-x thin films

International Nuclear Information System (INIS)

McGuire, T.R.; Gupta, A.; Koren, G.; Laibowitz, R.B.; Dimos, D.

1989-01-01

Magnetic and transport measurements on 0.3 micron thick films of YBa 2 Cu 3 O 7 - x made by a laser ablation technique show critical current densities of up to 40X10 6 amps/cm 2 . At 77K the transport data gives J c ∼5x10 6 amps/cm 2 while magnetic data is 40 % lower. Comparison is made with evaporated films

Heteroepitaxial growth of strained multilayer superconducting thin films of Nd1.83Ce0.17CuOx/YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Gupta, A.; Gross, R.; Olsson, E.; Segmueller, A.; Koren, G.; Tsuei, C.C.

1990-01-01

Heteroepitaxial growth of strained multilayer thin films of YBa 2 Cu 3 O 7-δ /Nd 1.83 Ce 0.17 CuO x by pulsed-laser deposition is reported. The coherency strain results in biaxial compression of the tetragonal Nd 1.83 Ce 0.17 CuO x layers, whereas the biaxial tension in the YBa 2 Cu 3 O 7-δ layers removes the orthorhombic distortion and makes the unit cell isotropic in the basal plane (a=b). Depending on their oxygen content, either the YBa 2 Cu 3 O 7-δ or the Nd 1.83 Ce 0.17 CuO x layers are superconducting in these multilayers. The strain-induced structural modification has a significant influence on the superconducting transition temperature of the YBa 2 Cu 3 O 7-δ layers

Surface resistance of YBa2Cu3O7 films deposited on LaGaO3 substrates

International Nuclear Information System (INIS)

Cooke, D.W.; Gray, E.R.; Houlton, R.J.; Javadi, H.H.S.; Maez, M.A.; Bennett, B.L.; Rusnak, B.; Meyer, E.A.; Arendt, P.N.; Beery, J.G.; Brown, D.R.; Garzon, F.H.; Raistriek, I.D.; Bolmaro, B.; Elliott, N.E.; Rollett, A.D.; Klein, N.; Muller, G.; Orbach, S.; Piel, H.; Josefowicz, J.Y.; Rensch, O.B.; Drabeck, L.; Gruner, G.

1989-01-01

Superconducting films of YBa 2 Cu 3 O 7 deposited onto LaGaO 3 substrates were prepared by e-beam and magnetron sputtering techniques. Surface resistance measurements made at 22 GHz, 86 GHz, and 148 GHz show that these films are superior to those deposited by similar techniques onto SrTiO 3 . Typical surface resistance values measured at 22 GHz and 12 K are ∼2 m(cgom) with the lowest value being 0.2 m(cgom), which is only 2 to 4 times higher than Nb. The surface resistance is proportional to the square of the measuring frequency

YBa2Cu3O(7-x) based superconducting thin films by multitarget sputtering

International Nuclear Information System (INIS)

Bouteloup, E.; Mercey, B.; Poullain, G.; Brousse, T.; Murray, H.; Raveau, B.

1990-01-01

This paper reports a new technique to prepare superconducting YBa 2 Cu 3 O (7-x) thin films. The multitarget sputtering apparatus described below allows the simultaneous and reproducible production of numerous films with a metallic composition close to Y 17% Ba 33% Cu 50% . Superconducting films (R = 0) at 80 K have been produced on polycrystalline zirconia substrates after a high temperature annealing [fr

Artificial in-plane ordering of textured YBa2Cu3O(7-x) films deposited on polycrystalline yttria-stabilized zirconia substrates

Science.gov (United States)

Harshavardhan, K. S.; Rajeswari, M.; Hwang, D. M.; Chen, C. Y.; Sands, T. D.; Venkatesan, T.; Tkaczyk, J. E.; Lay, K. W.; Safari, A.; Johnson, L.

1992-12-01

Anisotropic surface texturing of the polycrystalline yttria-stabilized zirconia substrates, prior to YBa2Cu3O(7-x) film deposition, is shown to promote in-plane (basal plane) ordering of the film growth in addition to the c-axis texturing. The Jc's of the films in the weak-link-dominated low-field regime are enhanced considerably, and this result is attributed to the reduction of weak links resulting from a reduction in the number of in-plane large-angle grain boundaries.

Physical and chemical properties of YBa2Cu3O7 thin films

International Nuclear Information System (INIS)

El-Samahi, M.I.

1991-12-01

Investigations were carried out to determine the influence of different annealing processes on the superconducting properties of the YBa 2 Cu 3 O 7 thin films. The samples were produced by means of coevaporation of Cu, Y and Ba on polycrystalline yttria stabilized (YSZ) ZrO 2 and single crystal SrTiO 3 (001) substrates. Subsequently, the as-deposited films were subjected to two different annealing methods to crystallize the superconducting phase YBa 2 Cu 3 O 7 : (i) heating up, annealing and cooling in an oxygen atmosphere and (ii) heating up in an innert gas atmosphere up to the maximum annealing temperature (T max ) and then annealing and cooling under oxygen. (orig.)

Quasi-homoepitaxial growth of a-axis oriented PrBa sub 2 Cu sub 3 O sub 7 sub - subdelta thick film on (100) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single crystal

CERN Document Server

Sato, M; Morishita, T

2003-01-01

The structural characterizations of the quasi-homoepitaxial growth of a-axis oriented PrBa sub 2 Cu sub 3 O sub 7 sub - subdelta thick film grown on (100) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single crystal were investigated in comparison with those of the film grown on (001) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single crystal. The a-axis oriented PrBa sub 2 Cu sub 3 O sub 7 sub - subdelta films, expected to be a barrier layer, were prepared using a dc-95 MHz hybrid plasma sputtering on (100) and (001) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single crystals that are superconducting ground planes. The atomic force microscopy image revealed that the surfaces of 700-nm-thick a-axis PrBa sub 2 Cu sub 3 O sub 7 sub - subdelta films on (100) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single crystals were smooth with a mean roughness of 2.8 nm. X-ray diffraction scans showed that a-axis PrBa sub 2 Cu sub 3 O sub 7 sub - subdelta films deposited on (100) YBa sub 2 Cu sub 3 O sub 7 sub - subdelta single cry...

Phase Evolution of YBa2Cu3O7-x films by all-chemical solution deposition route for coated conductors

DEFF Research Database (Denmark)

Yue, Zhao; Tang, Xiao; Wu, Wei

2014-01-01

In order to understand the all-chemical-solution-deposition (CSD) processes for manufacturing coated conductors, we investigated the phase evolution of YBa2Cu3O7 (YBCO) films deposited by a low-fluorine metal-organic solution deposition (LF-MOD) method on CSD derived Ce0.9La0.1O2/Gd2Zr2O7/Ni......W. It is shown that the phase transition from the pyrolyzed film to fully converted YBCO film in the LF-MOD process is similar to that in typical trifluoroacetates-metal organic deposition (TFA-MOD) processes even though the amount of TFA in the solution is reduced by almost one half compared with typical TFA...

Critical current density in (YBa2Cu3O7-δ)1-x-(PrBa2Cu3O7-δ)x melt-textured composites

Science.gov (United States)

Opata, Yuri Aparecido; Monteiro, João Frederico Haas Leandro; Jurelo, Alcione Roberto; Siqueira, Ezequiel Costa

2018-06-01

Melt textured (YBa2Cu3O7-δ)1-x-(PrBa2Cu3O7-δ)x composites (x = 0.00 and x = 0.05) were grown using the top seeding method. The effect of the PrBa2Cu3O7-δ phase on the growth process and the modification of the microstructure as well as on the physical properties was analyzed. X-ray analyses indicated that both pure and Pr-doped samples present an orthorhombic superconducting phase. From resistivity measurements for YBa2Cu3O7-δ and (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 samples, the Tcab did not change and was around 90.5 K. However, from magnetic measurements, the superconductivity was observed in critical temperatures TC = 92.9 K and 92.4 K for YBa2Cu3O7-δ and (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 samples, respectively. The YBa2Cu3O7-δ sample showed higher critical current densities than those shown by the (YBa2Cu3O7-δ)0.95-(PrBa2Cu3O7-δ)0.05 sample, with values of JC = 5.85 × 105 A/cm2 and 4.72 × 105 A/cm2, respectively. This paper also discusses the importance of Pr substitution on nano- and micro-meter scales to enhance JC(H).

Anisotropic electrical properties of epitaxial Yba2Cu3O7-gd films on (110) SrTiO3

International Nuclear Information System (INIS)

Gupta, A.; Koren, G.; Baseman, R.J.; Segmuller, A.; Holber, W.

1989-01-01

Epitaxial thin films of YBa 2 Cu 3 O 7 - δ were deposited on (110) SrTiO 3 at 600 degrees C in the presence of atomic oxygen using the laser ablation technique. X-ray diffraction patterns in the standard Bragg and grazing incidence modes show epitaxial growth of the films with their c-axis and axis parallel to the and directions in the plane of the substrate, respectively. Superconductivity with T c (R = ) = 82 K was found along the direction in the basal plane, whereas finite resistivity down to 5 k was observed along the c-axis direction. The authors maintain that these preliminary results suggest that YBa 2 Cu 3 O 7 - δ behaves like a true two-dimensional superconductor

Off-axis sputter deposition of YBa2Cu3O7 thin films for microwave applications

International Nuclear Information System (INIS)

Greene, L.H.; Bagley, B.G.; Feldmann, W.L.; Barner, J.B.; Shokoohi, F.; Miceli, P.; Wilkens, B.J.; Fathy, A.; Kalokitis, D.; Pendrick, V.

1991-01-01

Thin films of superconducting YBa 2 Cu 3 O 7 were grown in situ by off-axis sputter deposition for microwave device fabrication. These ∼1 cm 2 films, which are reproducible, exhibit midpoint T c 's of 89--90.5 K as measured by ac susceptibility, ion channeling yields of 4.7%--6%, and c-axis rocking-curve half-widths of 0.5 degree, even with a rich microstructure as seen by scanning electron microscopy. Two films were photodefined into miniature X-band microwave bandpass filters. These narrow-band filters (0.5% bandwidth) exhibited 4.4-and 4.5-dB insertion losses at 77 K and 9.25 GHz, with little temperature dependence below 80 K

Critical current density of strained multilayer thin films of Nd1.83Ce0.17CuOx/YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Gross, R.; Gupta, A.; Olsson, E.; Segmueller, A.; Koren, G.

1990-01-01

The superconducting transport properties of strained multilayer thin films of YBa 2 Cu 3 O 7-δ / Nd 1.83 Ce 0.17 CuO x , grown heteroepitaxially by laser ablation deposition, are reported. For individual layer thicknesses below a critical layer thickness of about 250 A, coherency strain removes the orthorhombic distortion in the YBa 2 Cu 3 O 7-δ layers and makes them twin-free. Zero-field critical current densities as high as 1.1x10 7 A/cm 2 at 77 K have been measured for the YBa 2 Cu 3 O 7-δ layers. Flux pinning energies at zero temperature and zero magnetic field in the range of 80--140 meV have been found

Oxygen isotope effect in YBa2Cu3O7 prepared by burning YBa2Cu3 in 16O and 18O

Science.gov (United States)

Yvon, Pascal J.; Schwarz, R. B.; Pierce, C. B.; Bernardez, L.; Conners, A.; Meisenheimer, R.

1989-04-01

We prepared YBa2Cu3 powder by ball milling a 2:1 molar mixture of the intermetallics BaCu and CuY. We synthesized YBa2Cu3(16O)7-x and YBa2Cu3(18O)7-x by oxidizing the YBa2Cu3 powder in 16O and 18O. The 16O/18O ratios were determined by laser-ionization and sputtering-ionization mass spectroscopy. The YBa2Cu3(160)7-x sample had 99.8 at. %16O, and the YBa2Cu3(18O)7-x sample had 96.5 at. %18O. Susceptibility measurements of the superconducting transition temperature (Tc=91.7 K for 16O; half-point transition at 84 K show an isotope effect of 0.4+/-0.1 K.

Proximity-effect and tunneling in YBa2Cu3O7/metal layered structures

International Nuclear Information System (INIS)

Greene, L.H.; Feldmann, W.L.; Barner, J.B.; Farrow, L.A.; Miceli, P.F.; Ramesh, R.; Wilkens, B.J.; Bagley, B.G.; Giroud, M.; Rowell, J.M.

1990-01-01

Superconducting thin films of YBa 2 Cu 3 O 7 are prepared in-situ by on-axis sputter deposition from a single, composite target. The planar magnetron target composition of YBa:Cu = 1.08:1.76:4.5 sputtered onto MgO at T ∼ 750 degrees C in a 600 mTorr Ar-O 2 atmosphere yields reproducible superconducting films having T c (R = 0) > 80 K and stoichiometry 1:2:3, that are shiny and of near epitaxial crystalline quality. In order to ensure clean interfaces, YBa 2 Cu 3 O 7 /normal metal bilayers (to form SNS' Josephson junctions) and YBa 2 Cu 3 O 7 /normal metal/insulating barrier trilayers (to form SNIS' proximity tunnel junctions) are grown completely in-situ. (The S' = Pb counter electrode is evaporated ex-situ.) A supercurrent and Shapiro steps are observed in microwave irradiated SNS' (N = Ag) small area (5 x 10 -5 cm 2 junctions. In SNIS' tunnel junctions, high-quality Pb tunnelling is observed

Epitaxial YBa2Cu3O7-δ/Sr2RuO4 heterostructures

International Nuclear Information System (INIS)

Schlom, D.G.; Merritt, B.A.; Madhavan, S.

1997-01-01

The anisotropic oxide superconductors YBa 2 Cu 3 O 7-δ and Sr 2 RuO 4 have been epitaxially combined in various ways (c-axis on c-axis, c-axis on a-axis, and a-axis on a-axis) though the use of appropriate substrates. Phase-pure a-axis oriented or c-axis oriented epitaxial Sr 2 RuO 4 films were grown by pulsed laser deposition. YBa 2 Cu 3 O 7-δ films were then grown on both orientations of Sr 2 RuO 4 films and the resulting epitaxy was characterized

On possibility of BaCeO3 production when depositing YBa2Cu3O7-χ films on a cerium oxide surface

International Nuclear Information System (INIS)

Mashtakov, A.D.; Kotelyanskij, I.M.; Luzanov, V.A.; Mozhaev, P.B.; Ovsyannikov, G.A.; Bdikin, I.D.

1997-01-01

Consideration is given to experimental results of investigation into crystallographic parameters of hetero-structural (1102)Al 2 O 3 /(001)CeO 2 (001)YBa 2 Cu 3 O 7-χ films, prepared by the method of cathode sputtering at substrate temperature, equal to 600-800 deg C. It is shown that main limitation for precipitation temperature of YBa 2 Cu 3 O 7-χ film on CeO 2 surface is caused by chemical interaction of YBa 2 Cu 3 O 7-χ with CeO 2 with formation of polycrystalline BaCeO 3 layer

Anomalous misfit strain relaxation in ultrathin YBa2Cu3O7-δ epitaxial films

International Nuclear Information System (INIS)

Kamigaki, K.; Terauchi, H.; Terashima, T.; Bando, Y.; Iijima, K.; Yamamoto, K.; Hirata, K.; Hayashi, K.; Nakagawa, I.; Tomii, Y.

1991-01-01

Ultrathin YBa 2 Cu 3 O 7-δ epitaxial films were successfully grown in situ on (001) SrTiO 3 and MgO substrates by means of ozone-incorporating activated reactive evaporation. The x-ray-diffraction study was carefully examined to determine the structural properties of the grown films. Excellent crystallinity with no interfacial disorders was revealed by the appearance of the Laue oscillations. It was found that in a well lattice-matched YBa 2 Cu 3 O 7-δ /SrTiO 3 system, the crystallinity was deteriorated due to defect introduction at the critical layer thickness h c ( ∼ 130 A). Interestingly, also in a poorly lattice-matched YBa 2 Cu 3 O 7-δ /MgO system, excellent crystallinity was revealed even at above h c ( 2 Cu 3 O 7-δ /MgO system. In such a system, no crystal imperfection of the MgO substrate caused by defect introduction was elucidated by the grazing incidence x-ray scattering, which indicated that the MgO substrate did not contribute to the anomalous misfit relaxation. The anomalous growth manner was also found in YBa 2 Cu 3 O 7-δ /MgO according to surface morphology investigations. Below 40 A( > h c ), island nucleation growth was found. Above 40 A, it was observed that an atomically smooth surface was obtained and the crystallinity was simultaneously improved. It is suggested that YBa 2 Cu 3 O 7-δ possesses an anomalous misfit relaxation mechanism, and that especially in the growth on MgO, it couples with the characteristic growth behavior at the initial stage

Epataxial growth of the high-temperature superconductors YBa2Cu3O7-x on silicon single crystals with buffer layers

International Nuclear Information System (INIS)

Lubig, A.

1991-09-01

In this work the growth of thin films of the high-temperature superconductor YBa 2 Cu 3 O 7-x on Si(001) substrates has been investigated by Rutherford backscattering, channeling, X-ray diffraction, high resolution transmission electron microscopy, and electrical measurements. Epitaxial buffer layers of electrically insulating, pure and yttria-stabilized ZrO 2 ([Y 2 O 3 ] 0.06 [ZrO 2 ] 0.94 = YSZ) as well as of metallic CoSi 2 were employed to largely prevent the interdiffusion and chemical reaction between the superconductor film and the substrate in spite of the high deposition temperatures of the YBa 2 Cu 3 O 7-x in the range of 600 to 800deg C. (orig.)

Critical current density of strained multilayer thin films of Nd sub 1. 83 Ce sub 0. 17 CuO sub x /YBa sub 2 Cu sub 3 O sub 7 minus. delta

Energy Technology Data Exchange (ETDEWEB)

Gross, R.; Gupta, A.; Olsson, E.; Segmueller, A.; Koren, G. (IBM T. J. Watson Research Center, P.O. Box 218, Yorktown Heights, New York 10598 (USA))

1990-07-09

The superconducting transport properties of strained multilayer thin films of YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}}/ Nd{sub 1.83}Ce{sub 0.17}CuO{sub {ital x}}, grown heteroepitaxially by laser ablation deposition, are reported. For individual layer thicknesses below a critical layer thickness of about 250 A, coherency strain removes the orthorhombic distortion in the YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} layers and makes them twin-free. Zero-field critical current densities as high as 1.1{times}10{sup 7} A/cm{sup 2} at 77 K have been measured for the YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} layers. Flux pinning energies at zero temperature and zero magnetic field in the range of 80--140 meV have been found.

Surface studies of YBa2Cu3O7-x -matching oxide substrates and interfaces

International Nuclear Information System (INIS)

Enevold Thaulov Andersen, J.

1990-11-01

Crystallographic changes as a result of heat-treatment at 700-900 deg. C are found for SrTiO 3 (100), MgO(100) and LaAlO 3 (100). The p(2x2) reconstruction of the SrTiO 3 (100) and the superstructures on MgO(100) and on LaAlO 3 (100) thus observed are suggested to be induced by segregation of impurities to the surface. The surface charge-effects which disturb electron- and photon-impact experiments with these insulators are removed by heat-treatments. Deposition of copper results in formation of copper islands on SrTiO 3 (100) and on LaAlO 3 (100). Yttrium forms islands on LaAlO 3 (100) and grows in a layer-by-layer mode on SrTiO 3 (100) and on MgO(100). An yttrium 1x1 epitaxy is observed on the MgO(100) surface, which is suggested to be an YO superstructure. Oxidation of the 1x1 Y/MgO(100) systems diminishes the charge-effects and improves all diffraction and spectroscopic measurements. This may be due to the formation of metallic states around the Fermi level when the film is oxidized. An in situ synthesized YBa 2 Cu 3 O 7 thin film on SrTiO 3 (100) compared to a thick epitaxial YBa 2 Cu 3 O 7-x (001) film on MgO(100) reveals differences in surface electronic structures but not in surface stoichiometries. (au) 18 refs

Effect of Y2O3 Nanoparticles on Critical Current Density of YBa2Cu3O7-x Thin Films

International Nuclear Information System (INIS)

Tran, H. D.; Reddy, Sreekantha; Wie, C. H.; Kang, B.; Oh, Sang Jun; Lee, Sung Ik

2009-01-01

Introduction of proper impurity into YBa 2 Cu 3 O 7-x (YBCO) thin films is an effective way to enhance its flux-pinning properties. We investigate effect of Y 2 O 3 nanoparticles on the critical current density J c of the YBCO thin films. The Y 2 O 3 nanoparticles were created perpendicular to the film surface (parallel with the c-axis) either between YBCO and substrate or on top of YBCO, YBCO/Y 2 O 3 /LAO or Y 2 O 3 /YBCO/STO, by pulsed laser deposition. The deposition temperature of the YBCO films were varied (780 degree C and 800 degree C) to modify surface morphology of the YBCO films. Surface morphology characterization revealed that the lower deposition temperature of 780 degree C created nano-sized holes on the YBCO film surface which may behave as intrinsic pinning centers, while the higher deposition temperature produced much denser and smoother surface. J-c values of the YBCO films with Y 2 O 3 particles were either remained nearly the same or decreased for the samples in which YBCO is grown at 780 degree C. On the other hand, J-c values were enhanced for the samples in which YBCO is grown at higher temperature of 800 degree C. The difference in the effect of Y 2 O 3 can be explained by the fact that the higher deposition temperature of 800 degree C reduces intrinsic pinning centers and J c is enhanced by introduction of artificial pinning centers in the form of Y 2 O 3 nanoparticles.

Patterned YBa2Cu3O7-x thin films from photopolymerizable precursors

International Nuclear Information System (INIS)

Hung, Y.; Agostinelli, J.A.

1990-01-01

A technique which combines the fabrication and patterning of thin films of the high T c superconductor YBa 2 Cu 3 O 7-x has been developed. The technique possesses the essential features of the metalorganic decomposition method with the additional attribute that the metalorganic precursor is photopolymerizable. Patterns are generated directly in the precursor film using optical exposure through a mask followed by development in a solvent. A subsequent thermal treatment transforms the patterned precursor film to the oriented superconducting phase with c axis perpendicular to the substrate surface. Resistivity measurements for such a patterned film on a single crystal (100)MgO substrate show an onset to the superconducting state occurring at 85 K with zero resistivity below 67 K

Analysis of process parameters in the laser deposition of YBa{sub 2}Cu{sub 3}O{sub 7} superconducting films by using SVR

Energy Technology Data Exchange (ETDEWEB)

Cai, C.Z., E-mail: caiczh@gmail.com [Department of Applied Physics, Chongqing University, Chongqing 401331 (China); Xiao, T.T. [Department of Applied Physics, Chongqing University, Chongqing 401331 (China); Science and Technology on Plasma Physics Laboratory, Research Center of Laser Fusion, CAEP, P.O. Box 919-988, Mianyang 621900 (China); Tang, J.L.; Huang, S.J. [Department of Applied Physics, Chongqing University, Chongqing 401331 (China)

2013-10-15

Highlights: • Proposed new ideas and strategies to improve energy storage density for SMES system. • One is to increase the effective current density in the superconducting coils. • Another is to optimize the configuration of the SMES coil. • A new conceive of energy compression is also proposed. -- Abstract: There are several process parameters in the growth of YBa{sub 2}Cu{sub 3}O{sub 7} superconducting films by using pulsed laser deposition (PLD). The relationship between the response and process parameters is highly nonlinear and quite complicated. It is very valuable to quantitatively estimate the response under different deposition parameters. In this study, according to an experimental data set on the superconducting transition temperature (T{sub c}) and relative resistance ratio (r{sub R}) of 17 samples of YBa{sub 2}Cu{sub 3}O{sub 7} films deposited under various parameters, the support vector regression (SVR) combined with particle swarm optimization (PSO), was proposed to predict the T{sub c} and r{sub R} for YBa{sub 2}Cu{sub 3}O{sub 7} films. The prediction performance of SVR was compared with that of multiple regression analysis (MRA) models. The results strongly support that the generalization ability of SVR model consistently surpasses that of MRA via leave-one-out cross validation (LOOCV). The mean absolute percentage errors for T{sub c} and r{sub R} are 0.37% and 1.51% respectively via LOOCV test of SVR. Sensitivity analysis discovered the most sensitive parameters affecting the T{sub c} and r{sub R}. This study suggests that the established SVR model can be used to accurately foresee the T{sub c} and r{sub R}. And it can be used to optimizing the deposition parameters in the development of YBa{sub 2}Cu{sub 3}O{sub 7} films via PLD.

Buffer layers for growth of the YBa sub 2 Cu sub 3 O sub 7 sub - sub x films on silicon

CERN Document Server

Razumov, S V

2001-01-01

The results of the studies on the structural characteristics of the SrTiO sub 3 , NdGaO sub 3 and CeO sub 2 buffer layers, obtained through the ion-plasma spraying on the silicon substrates, are presented. It is shown that the phase composition and internal stresses in the films are strongly dependent on the deposition temperature. The technological conditions of growth of primarily oriented SrTiO sub 3 , NdGaO sub 3 and CeO sub 2 films are dortmund. The structural quality of the obtained buffer films is sufficient for further growth of the YBa sub 2 Cu sub 3 O sub 7 sub - sub x high-quality films on the silicon substrates

Electron scattering rate in epitaxial YBa2Cu3O7 superconducting films

Science.gov (United States)

Flik, M. I.; Zhang, Z. M.; Goodson, K. E.; Siegal, M. P.; Phillips, Julia M.

1992-09-01

This work determines the electron scattering rate in the a-b plane of epitaxial YBa2Cu3O7 films using two techniques. Infrared spectroscopy yields the scattering rate at temperatures of 10, 78, and 300 K by fitting reflectance data using thin-film optics and a model for the free-carrier conductivity. The scattering rate is also obtained using kinetic theory and an extrapolation of normal-state electrical resistivity data to superconducting temperatures based on the Bloch theory for the phonon-limited electrical resistivity of metals. The scattering rates determined using both techniques are in agreement and show that the electron mean free path in the a-b plane of YBa2Cu3O7 superconducting films is three to four times the coherence length. Hence YBa2Cu3O7 is pure but not in the extreme pure limit. An average defect interaction range of 4 nm is obtained using the defect density resulting from flux-pinning considerations.

Analysis of low-field isotropic vortex glass containing vortex groups in YBa2Cu3O7-x thin films visualized by scanning SQUID microscopy

NARCIS (Netherlands)

Wells, Frederick S.; Pan, Alexey V.; Wang, X.; Fedoseev, Sergey A.; Hilgenkamp, Hans

2015-01-01

The glass-like vortex distribution in pulsed laser deposited YBa2Cu3O7-x thin films is observed by scanning superconducting quantum interference device microscopy and analysed for ordering after cooling in magnetic fields significantly smaller than the Earth's field. Autocorrelation calculations on

YBa2Cu3O7-x thin films prepared by chemical solution deposition

International Nuclear Information System (INIS)

Apetrii, Claudia

2009-01-01

The discovery of superconductivity in ceramic materials by Bednorz and Mueller in early 1987, immediately followed by Wu et al., who showed that YBa 2 Cu 3 O 7-x (YBCO) becomes superconducting (92 K) well above the boiling point of nitrogen (77 K) created a great excitement in superconductivity research. Potential applications of high T c -superconductors require large critical currents and high-applied magnetic fields. Effective ways to increase the critical current density at high magnetic fields in YBCO are the introduction of nanoparticles and chemical substitution of yttrium by other rare earth elements. Since low costs and environmental compatibility are essential conditions for the preparation of long length YBCO films, the cost effective chemical solution deposition (CSD) procedure was selected, given that no vacuum technology is required. To reveal the flexibility and the good optimization possibilities of the CSD approach two main processes were chosen for comparison: a fluorine-free method, namely the polymer-metal precursor technique, and a fluorine-based method, the metalorganic deposition (MOD) using the trifluoroacetates (TFA) technique. Sharp transition temperature widths ΔT c of 1.1 K for the polymer metal method, 0.8 K for TFA method and critical current densities J c of ∼3.5 MA/cm 2 shows that high quality YBCO thin films can be produced using both techniques. Especially interesting is the magnetic field dependence of the critical current density J c (B) of the Y(Dy)BCO (80 %) films showing that for the lower magnetic fields the critical current density J c (B) is higher for a standard YBCO film, but at fields higher than 4.5 T the critical current density J c (B) of Y(Dy)BCO is larger than that for the YBCO. Above 8 T, J c (B) of the Y(Dy)BCO film is more than one order of magnitude higher than in pure YBCO film. (orig.)

Rapid processing method for solution deposited YBa2Cu3O7-δ thin films

International Nuclear Information System (INIS)

Dawley, J.T.; Clem, P.G.; Boyle, T.J.; Ottley, L.M.; Overmyer, D.L.; Siegal, M.P.

2004-01-01

YBa 2 Cu 3 O 7-δ (YBCO) films, deposited on buffered metal substrates, are the primary candidate for second-generation superconducting (SC) wires, with applications including expanded power grid transmission capability, compact motors, and enhanced sensitivity magnetic resonance imaging. Feasibility of manufacturing such superconducting wires is dependent on high processing speed, often a limitation of vapor and solution-based YBCO deposition processes. In this work, YBCO films were fabricated via a new diethanolamine-modified trifluoroacetic film solution deposition method. Modifying the copper chemistry of the YBCO precursor solution with diethanolamine enables a hundredfold decrease in the organic pyrolysis time required for MA/cm 2 current density (J c ) YBCO films, from multiple hours to ∼20 s in atmospheric pressure air. High quality, ∼0.2 μm thick YBCO films with J c (77 K) values ≥2 MA/cm 2 at 77 K are routinely crystallized from these rapidly pyrolyzed films deposited on LaAlO 3 . This process has also enabled J c (77 K)=1.1 MA/cm 2 YBCO films via 90 m/h dip-coating on Oak Ridge National Laboratory RABiTS textured metal tape substrates. This new YBCO solution deposition method suggests a route toward inexpensive and commercializable ∼$10/kA m solution deposited YBCO coated conductor wires

YBa2Cu3O7-δ/NdBa2(Cu1-xNix)3O7-δ double layers by liquid-phase epitaxial growth

International Nuclear Information System (INIS)

Yao, X.; Izumi, Toru; Hobara, Natsuro; Nakamura, Yuichi; Izumi, Teruo; Shiohara, Yuh

2001-01-01

Our present investigation has answered questions pertaining to the REBa 2 Cu 3 O 7-δ (RE123, RE=rare-earth elements)-coated conductor application when NdBa 2 (Cu 1-x Ni x ) 3 O 7-δ (Ni-NdBCO) solid solution is used as a buffer layer by the liquid-phase epitaxy(LPE) process. The NiO/Ni substrate has no substantial reaction in the Ni-saturated Nd-Ba-Cu-O liquid. There is no essential Ni interdiffusion between YBa 2 Cu 3 O 7-δ (YBCO) and Ni-NdBCO LPE thick films as evident from T c values of 90 K obtained from multilayer YBCO/Ni-NdBCO samples. (author)

Interface structure and electronic properties of SrTiO3 and YBa2Cu3O7-δ crystals and thin films

International Nuclear Information System (INIS)

Thiess, S.

2007-01-01

Two new extensions of the X-ray standing wave (XSW) technique, made possible by the intense highly collimated X-ray beams from undulators at the ESRF, are described in this thesis. First, the XSW method was applied in a structural study to solve the nucleation mechanism of the high temperature superconductor YBa 2 Cu 3 O 7-δ on the (001) surface of SrTiO 3 . Second, the valence electronic structures of SrTiO 3 and YBa 2 Cu 3 O 7-δ were investigated. Finally, recent developments in the field of photoelectron spectroscopy in the hard X-ray region are described. The X-ray standing wave method is used in combination with fluorescence, Auger or photoelectron spectroscopy and lends very high spatial resolution power to these analytical techniques. Previously, the XSW method has been used for structure determination of surfaces and interfaces. The currently available X-ray intensities permit extensions to the XSW technique. Two recently established applications, described in this thesis, are XSW real space imaging and XSW valence electronic structure analysis. XSW real space imaging was employed to analyse the atomic structure of 0.5 and 1.0 layers of YBa 2 Cu 3 O 7-δ deposited on SrTiO 3 (001). Three-dimensional images of the atomic distributions were reconstructed for each of the elements from experimentally determined Fourier components of the atomic distribution functions. The images confirmed the formation of a perovskite precursor phase prior to the formation of the YBa 2 Cu 3 O 7-δ phase during the growth of the first monolayer of the film. XSW valence electronic structure analysis applied to SrTiO 3 identified the valence band contributions arising from the strontium, titanium, and oxygen sites of the crystal lattice. Relations between the site-specific valence electronic structure and the lattice structure were established. The experimental results agree very well with predictions by state-of-the-art ab initio calculations. X-ray absorption cross sections for

Interdiffusion studies on high-Tc superconducting YBa2Cu3O7-δ thin films on Si(111) with a NiSi2/ZrO2 buffer layer

DEFF Research Database (Denmark)

Aarnink, W.A.M.; Blank, D.H.A.; Adelerhof, D.J.

1991-01-01

Interdiffusion studies on high-T(c) superconducting YBa2Cu3O7-delta thin films with thickness in the range of 2000-3000 angstrom, on a Si(111) substrate with a buffer layer have been performed. The buffer layer consists of a 400 angstrom thick epitaxial NiSi2 layer covered with 1200 angstrom...... of polycrystalline ZrO2. YBa2Cu3O7-delta films were prepared using laser ablation. The YBa2Cu3O7-delta films on the Si/NiSi2/ZrO2 substrates are of good quality; their critical temperatures T(c,zero) and T(c,onset) have typical values of 85 and 89 K, respectively. The critical current density j(c) at 77 K equaled 4...... x 10(4) A/cm2. With X-ray analysis (XRD), only c-axis orientation has been observed. The interdiffusion studies, using Rutherford backscattering spectrometry (RBS) and scanning Auger microscopy (SAM) show that the ZrO2 buffer layer prevents severe Si diffusion to the YBa2Cu3O7-delta layer, the Si...

Effect of the post-deposition processing ambient on the preparation of superconducting YBa2Cu3O/sub 7-//sub x/ coevaporated thin films using a BaF2 source

International Nuclear Information System (INIS)

Chan, S.; Bagley, B.G.; Greene, L.H.; Giroud, M.; Feldmann, W.L.; Jenkin, K.R. II; Wilkins, B.J.

1988-01-01

We have investigated the effect of the post-deposition processing ambient on the preparation of YBa 2 Cu 3 O/sub 7-//sub x/ thin films from a BaF 2 source. The role of H 2 O vapor during the high-temperature anneal is understood through a thermodynamic analysis of the fluorine removal reaction. The role of a HF getter (e.g., SiO 2 ) is understood through the same type of analysis. We have demonstrated that a zero resistance transition temperature at 77 K can be obtained for an annealing temperature as low as 690 0 C for films deposited on SrTiO 3 substrates by increasing the P/sub H>2/O$ and decreasing P/sub HF/ during the high-temperature soak cycle

Spectroscopic study of the CuO chains in YBa2Cu3O7-x

International Nuclear Information System (INIS)

Edwards, H.; Derro, D.J.; Barr, A.L.; Markert, J.T.; de Lozanne, A.L.

1996-01-01

We interpret our previously published results obtained using a technique called current-imaging tunneling spectroscopy (CITS) to study the detailed electronic structure of the CuO chains in the high-temperature superconductor YBa 2 Cu 3 O 7-x near the Fermi level. Our CITS data comprise sequences of 32 simultaneously obtained images taken at bias voltages ranging from -78 to 72 mV. Cross sections of the CITS data, normalized-conductance analysis, and logarithmic-derivative analysis allow us to examine in detail the behavior of electronic modulations along the CuO chains and the energy gap in the CuO chains of YBa 2 Cu 3 O 7-x . This new analysis lends a strong foundation to our previous interpretation of the CITS data [H. L. Edwards et al., Phys. Rev. Lett. 75, 1387 (1995)]. copyright 1996 American Vacuum Society

Microwave properties of YBa2Cu3O7-δ/PrBa2Cu3O7-δ superlattices

International Nuclear Information System (INIS)

Carlos, W.E.; Kaplan, R.; Lowndes, D.H.; Norton, D.P.

1992-01-01

We have used non-resonant microwave absorption to study c-axis YBa 2 Cu 3 O 7-δ /PrBa 2 Cu 3 O 7-δ superlattices and compare the response to a film of similarly grown YBa 2 Cu 3 O 7-δ (YBCO). Near the respective transition temperatures, the response of the superlattice samples and the YBCO film have similar amplitudes and orientation dependences. This is consistent with the microwave loss being related to magnetic flux penetration at (110) slip planes. At lower temperatures, the response of the superlattices is much stronger than that of the YBCO film and, while both responses are hysteretic at low temperatures, the widths of the hysteresis have opposite orientation dependences, which we attribute to the role of the PrBa 2 Cu 3 O 7-δ layers. (orig.)

A study on the superconducting properties of YBa{sub 2}Cu{sub 9-x}Nb{sub x}O{sup y} thin films

Energy Technology Data Exchange (ETDEWEB)

Srinivas, S.; Bhatnagar, A.K. [Univ. of Hyderabad (India); Pinto, R. [Solid State Electronics Group, Bombay (India)] [and others

1994-12-31

Effect of niobium substitution at the copper site in YBa{sub 2}Cu{sub 9}O{sub 7-x} was studied in thin film form. The films were deposited by laser ablation technique using the targets of the YBa{sub 2}Cu{sub 3-x}Nb{sub x}O{sub y} where x = 0.0, 0.025, 0.05, 0.1, 0.2, 0.4, 0.8 and 1.0 under identical deposition conditions on SrTiO{sub 9} <100> substrates. Films were characterized by XRD, resistivity, I-V and J{sub c} measurements. Films made from x = 0.025 and 0.05 concentrations of Nb substituted targets showed relatively improved superconducting properties compared to that of undoped films. The best 7 realized for x = 0.025 Nb concentration was 1.8 x 10{sup {sigma}} A/cm{sup 2} and for 0.05 Nb concentration it was 3.2x10{sup {sigma}} A/cm{sup 2} at 77K. However, degradation of the superconducting properties, with the increase of x {ge} 0.1 Nb concentration and drastic suppression and complete loss of superconductivity was noticed for x {ge} 0.4. The growth of impurity phase YBa{sub 2}NbO{sub 6} for x = 0.1 and above of Nb concentration was noticed from XRD patterns. However, the site occupancy of Nb could not be confirmed from these studies.

Investigation of Optically Modified YBa2Cu3O7–x Films by Means of X-ray Microanalysis Technique

Directory of Open Access Journals (Sweden)

Artūras JUKNA

2014-06-01

Full Text Available This work reports on investigation of remnant oxygen content in optically-modified regions of 0.3-mm-thick YBa2Cu3O7–x films, patterned by a laser-writing technique in an inert ambient gas atmosphere at room temperature. A laser-treated region of weak superconductivity with dimensions depending on the size of a laser spot, laser power, and initial content of oxygen is characterized by a lower oxygen content, weaker critical magnetic field, and suppressed both the superconducting critical temperature and the critical current density, as compared to the laser untreated regions. Optically induced (cw-laser, 532-nm-wavelength heating strongly affects a non-uniform distribution of remnant oxygen content in the film, depending both on the optical power and beam’s scanning velocity. A level of oxygen depletion and the size of the oxygen-deficient region have been directly estimated from scanning-electron-microscope spectra with the X-ray microanalysis technique. The results of our measurements were compared with results extracted from electric measurements, assuming a correlation between the remnant oxygen content and the electric transport properties of oxygen-deficient YBa2Cu3O7–x films. DOI: http://dx.doi.org/10.5755/j01.ms.20.2.6323

Dependences of microstructure and critical current density on the thickness of YBa2Cu3O7-x film prepared by pulsed laser deposition on buffered Ni–W tape

International Nuclear Information System (INIS)

Xu, Da; Wang, Ying; Liu, Linfei; Li, Yijie

2013-01-01

YBa 2 Cu 3 O 7−x (YBCO) films with different thicknesses were fabricated on buffered Ni–W tapes by pulsed laser deposition. The thickness dependences of microstructure and critical current density (J c ) of YBCO film were systematically investigated. The microstructure and surface morphology of YBCO film were characterized by X-ray diffraction, optical microscopy, field emission scanning electron microscopy and atomic force microscopy. And the critical current (I c ) of YBCO film was measured by the conventional four-probe method. We found that the full width at half maximum values of both omega and phi scan rocking curves, the content of a-axis oriented grain, and surface roughness of YBCO film all increased with augmenting the thickness of YBCO film. It was also found that with increasing the thickness of YBCO film from 0.3 μm to 1.5 μm, the I c of YBCO film increased from 72 A/cm to 248 A/cm and yet J c of YBCO film decreased from 2.1 × 10 6 A/cm 2 to 1.6 × 10 6 A/cm 2 . Our results indicated that the microstructure and J c of YBCO film were largely dependent on the thickness of YBCO film under the optimized deposition condition of substrate temperature. - Highlights: ► YBa 2 Cu 3 O 7−x (YBCO) films with different thicknesses were grown on metallic tapes. ► The texture and critical current were dependent on the thickness of YBCO film. ► Thickness effect was weakened by fabricating YBCO film layer by layer

Theoretical investigation of the Fermi surfaces of La2-xSrxCuO4 and YBa2Cu3O7

International Nuclear Information System (INIS)

Antonov, V.N.; Antonov, Vl.N.; Bar'yakhtar, V.G.; Baglyuk, A.I.; Maksimov, E.G.; Nemoshkalenko, V.V.; Perlov, A.Ya.; Savrasov, S.Yu.; Uspenskii, Yu.A.

1989-01-01

A theoretical investigation is made of the shape of the Fermi surface and of the constant-energy surfaces near the Fermi energy of the La 2-x Sr x CuO 4 and YBa 2 Cu 3 O 7 oxides by a self-consistent linear muffin-tin orbital method in the atomic sphere approximation (OMTO-ASA). It is shown that the Fermi surfaces of these compounds are strongly two-dimensional. The Fermi surface of La 2-x Sr x CuO 4 is a corrugated rounded box centered at the point Λ. The Fermi surface of YBa 2 Cu 3 O 7 consists of four sheets: an electron cushion at the point Λ and three nested hole surfaces centered at the point S. The electron cushion and one of the hole surfaces are strongly corrugated along the z direction. The theoretically calculated Fermi surfaces of La 2 CuO 4 and YBa 2 Cu 3 O 7 are compared with the experimental data on electron-positron annihilation

Critical current density in (YBa2Cu3O7−δ)1−x–(PrBa2Cu3O7−δ)x melt-textured composites  

DEFF Research Database (Denmark)

Opata, Yuri Aparecido; Monteiro, João Frederico Haas Leandro; Jurelo, Alcione Roberto

2018-01-01

Melt textured (YBa2Cu3O7−δ)1−x–(PrBa2Cu3O7−δ)x composites (x = 0.00 and x = 0.05) were grown using the top seeding method. The effect of the PrBa2Cu3O7−δ phase on the growth process and the modification of the microstructure as well as on the physical properties was analyzed. X-ray analyses...... indicated that both pure and Pr-doped samples present an orthorhombic superconducting phase. From resistivity measurements for YBa2Cu3O7−δ and (YBa2Cu3O7−δ)0.95–(PrBa2Cu3O7−δ)0.05 samples, the Tcab did not change and was around 90.5 K. However, from magnetic measurements, the superconductivity was observed...... in critical temperatures TC = 92.9 K and 92.4 K for YBa2Cu3O7−δ and (YBa2Cu3O7−δ)0.95–(PrBa2Cu3O7−δ)0.05 samples, respectively. The YBa2Cu3O7−δ sample showed higher critical current densities than those shown by the (YBa2Cu3O7−δ)0.95–(PrBa2Cu3O7−δ)0.05 sample, with values of JC = 5.85 × 105 A/cm2 and 4...

Epitaxial YBa2Cu3O7 films on rolled-textured metals for high temperature superconducting applications

International Nuclear Information System (INIS)

Norton, D.P.; Park, C.; Prouteau, C.

1998-04-01

The epitaxial growth of high temperature superconducting (HTS) films on rolled-textured metal represents a viable approach for long-length superconducting tapes. Epitaxial, 0.5 microm thick YBa 2 Cu 3 O 7 (YBCO) films with critical current densities, J c , greater than 1 MA/cm 2 have been realized on rolled-textured (001) Ni tapes with yttria-stabilized zirconia (YSZ)/CeO 2 oxide buffer layers. This paper describes the synthesis using pulsed-laser deposition (PLD) of epitaxial oxide buffer layers on biaxially-textured metal that comprise the so-called rolling-assisted biaxially-textured substrates (RABiTs trademark). The properties of the buffer and YBa 2 Cu 3 O 7 films on rolled-textured Ni are discussed, with emphasis given to the crystallographic and microstructural properties that determine the superconducting properties of these multilayer structures

Characterization and crystal defects of the new YBa2Cu3O7-x superconductor

International Nuclear Information System (INIS)

Boulesteix, C.; Ben Salem, M.; Mokrani, R.

1987-01-01

YBa 2 Cu 3 O 7-x superconductors from different origins have been studied by electron microscopy and X ray emission. This material has an easy clevage plane parallel to (001) making its observation easy. It has been shown that the preparation reaction was not complete for some superconducting materials. YBa 2 Cu 3 O 7-x crystals can be twinned (mechanical twins, ferroelastic material) but they are generally not, or have few twins. Another oxide has been encountered in epitaxial growth on YBa 2 Cu 3 O 7-x . A superlattice perpendicular to the common c axis has been observed probably due to a regular stacking of the both oxides [fr

Superconducting thin films of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Hudner, J.

1993-01-01

Thin films of the high temperature superconductor YBa 2 Cu 3 O 7-x (YBCO) are of significance in fundamental studies of oxide superconductors and for prospected electronic applications based on superconductors operating at liquid nitrogen temperatures (T= 77 K). Synthesis of YBCO thin films is complex and a large part of this thesis has been devoted to the elaboration of various techniques in forming YBCO thin films. A general observation was that synthesis of YBCO films exhibiting high zero-resistivity temperatures temperatures (T c ) ≥ 88 K and elevated critical current densities (J c ) ≥ 10 6 A/cm 2 at 77 K was possible under widely different conditions of film growth. For the BaF 2 -based method, various substrate materials were investigated. Among perovskite related substrates with low losses in the high frequency regime, LaA10 3 was found to yield YBCO films exhibiting the highest quality electrical properties. A study of YBCO film interaction with sapphire substrates was performed. It was suggested that the YBCO film on sapphire consists of weakly coupled superconducting grains. Compositional effects of Y, BA and Cu for MOCVD-YBCO films were examined with respect to morphology, structure, resistivity, as susceptibility and J c (T). High T c :s and J c :s were observed for an anomalous large compositional range of Cu in off-compositional YBCO films. This was shown to be related to the formation of Cu-rich precipitates embedded within a c-Axis oriented stoichiometric YBCO film matrix. Thermal critical current behavior at zero field in thin films of YBCO fabricated by various methods has been studied by three techniques: transport measurements on patterned microbridges, dc magnetization hysteresis loops using the Bean model and non-linear ac susceptibility analysis. Absolute critical current values obtained form the two former techniques when measured on the same YBCO film were observed to differ about a factor of two. The feasibility of non-linear ac

A study on the superconducting properties of YBa2Cu9-xNbxOy thin films

International Nuclear Information System (INIS)

Srinivas, S.; Bhatnagar, A.K.; Pinto, R.

1994-01-01

Effect of niobium substitution at the copper site in YBa 2 Cu 9 O 7-x was studied in thin film form. The films were deposited by laser ablation technique using the targets of the YBa 2 Cu 3-x Nb x O y where x = 0.0, 0.025, 0.05, 0.1, 0.2, 0.4, 0.8 and 1.0 under identical deposition conditions on SrTiO 9 substrates. Films were characterized by XRD, resistivity, I-V and J c measurements. Films made from x = 0.025 and 0.05 concentrations of Nb substituted targets showed relatively improved superconducting properties compared to that of undoped films. The best 7 realized for x = 0.025 Nb concentration was 1.8 x 10 σ A/cm 2 and for 0.05 Nb concentration it was 3.2x10 σ A/cm 2 at 77K. However, degradation of the superconducting properties, with the increase of x ≥ 0.1 Nb concentration and drastic suppression and complete loss of superconductivity was noticed for x ≥ 0.4. The growth of impurity phase YBa 2 NbO 6 for x = 0.1 and above of Nb concentration was noticed from XRD patterns. However, the site occupancy of Nb could not be confirmed from these studies

Processing of La(1.8)Sr(0.2)CuO4 and YBa2Cu3O7 superconducting thin films by dual-ion-beam sputtering

Science.gov (United States)

Madakson, P.; Cuomo, J. J.; Yee, D. S.; Roy, R. A.; Scilla, G.

1988-03-01

High-quality La(1.8)Sr(0.2)CuO4 and YBa2Cu3O7 superconducting thin films, with zero resistance at 88 K, have been made by dual-ion-beam sputtering of metal and oxide targets at elevated temperatures. The films are about 1.0 micron thick and are single phase after annealing. The substrates investigated are Nd-YAP, MgO, SrF2, Si, CaF2, ZrO2-(9 pct)Y2O3, BaF2, Al2O3, and SrTiO3. Characterization of the films was carried out using Rutherford backscattering spectroscopy, resistivity measurements, TEM, X-ray diffraction, and SIMS. Substrate/film interaction was observed in every case. This generally involves diffusion of the substrate into the film, which is accompanied by, for example, the replacement of Ba by Sr in the YBa2Cu2O7 structure, in the case of SrTiO3 substrate. The best substrates were those that did not significantly diffuse into the film and which did not react chemically with the film.

Properties of all YBa2Cu3O7 Josephson edge junctions prepared by in situ laser ablation deposition

International Nuclear Information System (INIS)

Koren, G.; Aharoni, E.; Polturak, E.; Cohen, D.

1991-01-01

Thin-film YBa 2 Cu 3 O 7 -YBa 2 Cu 3 O 7 edge junctions of 0.4x10 μm 2 cross section were prepared in situ by a multistep laser ablation deposition process. The fabrication time was about 3 h and the yield of good devices was 50%. Typical junctions reached zero resistance at 72 K and had a critical current density J c of 300 A/cm 2 at 70 K. Their J c as a function of temperature increased slowly with decreasing temperature down to 65 K and much faster below it. In the region of low J c we observed suppression of the critical current by a magnetic field. Under microwave radiation clear Shapiro steps were observed whose magnitude versus the microwave field agreed qualitatively with the resistively shunted junction model of a current biased junction

Theoretical investigation of the Fermi surface of La2-xSrxCuO4 and YBa2Cu3O7

International Nuclear Information System (INIS)

Antonov, V.N.; Antonov, V.N.; Bar'yakhtar, V.G.

1989-01-01

The theoretical investigation of both the Fermi surface (FS) form and isoenergetic surfaces near the Fermi energy of La 2-x Sr x CuO 4 and YBa 2 Cu 3 O 7 is carried out by selfconsistent LMTO/method in an atomic sphere approximation. The FS of these compounds is established to have an essential two-dimensional character. The FS La 2 CuO 4 is a corrugated rounded box centered in Γ point. The FS YBa 2 Cu 3 O 7 consists of four plates: an electron ''cushion'' in Γ point and three embeded hole surfaces centered in S point. In this case the ''cushion'' and one of the hole surfaces are vigorously corrugated along the z-direction. A comparison between both the FS calculated theoretically of La 2 CuO 4 and YBa 2 Cu 3 O 7 and experimental data on electron-positron annihilation is carried out. The electron-rate maps and numerical results of various characteristics, i.e., plate areas, mean rates, mean squares of the rates, partial densities of states for each plate of the FS YBa 2 Cu 3 O 7 are given

Melt-spin processing of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Folkerts, T.J.; Kramer, M.J.; McCallum, R.W.; Iowa State Univ. of Science and Technology, Ames, IA

1991-01-01

We introduce a novel containerless melt-spin processing technique for YBa 2 Cu 3 O 7-x using prereacted oxide powders which are rapidly melted and subsequentially quenched in a controlled atmosphere. This results in flakes with typical dimensions of 3000x150x15 μm 3 . Powder XRD indicates that all samples contain Y 2 O 3 , but that the Ba--Cu--O phases present depend on the processing parameters. SEM and TEM studies show these phases are finely dispersed: the typical grain size for Y 2 O 3 is 1--2 μm, and for the Ba--Cu--O phases it is <0.5 μm

Low resistivity contacts to YBa2Cu3O(7-x) superconductors

Science.gov (United States)

Hsi, Chi-Shiung; Haertling, Gene H.

1991-01-01

Silver, gold, platinum, and palladium metals were investigated as electroding materials for the YBa2Cu3O(7-x) superconductors. Painting, embedding, and melting techniques were used to apply the electrodes. Contact resistivities were determined by: (1) type of electrode; (2) firing conditions; and (3) application method. Electrodes fired for long times exhibited lower contact resistivities than those fired for short times. Low-resistivity contacts were found for silver and gold electrodes. Silver, which made good ohmic contact to the YBa2Cu3O(7-x) superconductor with low contact resistivities was found to be the best electroding material among the materials evaluated in this investigation.

Formation of high-Tc YBa2Cu3O(7-delta) films on Y2BaCuO5 substrate

Science.gov (United States)

Wang, W. N.; Lu, H. B.; Lin, W. J.; Yao, P. C.; Hsu, H. E.

1988-07-01

High-Tc superconducting YBa2Cu3O(7-delta) films have been successfully prepared on green Y2BaCuO5 (2115) ceramic substrate. The films have been formed by RF sputtering and screen printing with post annealing at 925 C. Regarding superconducting features, the sharp resistivity drop with Tc onset around 95 K (midpoint 84 K) and 99 K (midpoint 89 K) has been observed for RF sputtered and printed films respectively. Both films show the excellent adhesion towards the 2115 substrate. Powder X-ray diffraction profiles indicate a majority of 1237 phase with preferred orientation for RF sputtered thin film.

Microwave-detected optical response of YBa2Cu3O7-x thin films

International Nuclear Information System (INIS)

Kaplan, R.; Carlos, W.E.; Cukauskas, E.J.; Ryu, J.

1990-01-01

Microwave-detected optical response (MDOR) of YBa 2 Cu 3 O 7-x and other oxide superconductor thin films is shown to yield information complementary to that provided by trasnport photoconductivity measurements. The MDOR technique yields a superposition of response from all illuminated portions of a sample, irrespective of the existence of a resistive macroscopic percolative current path. The response is found to be bolometric at temperatures for which resistance appears in transport measurements. At low temperatures MDOR results imply a nonbolometric response which in some respects is consistent with nonequilibrium quasiparticle concentration due to radiative pair breaking

Laser wavelength dependent properties of YBa2Cu3O7-δ thin films deposited by laser ablation

International Nuclear Information System (INIS)

Koren, G.; Gupta, A.; Baseman, R.J.; Lutwyche, M.I.; Laibowitz, R.B.

1989-01-01

YBa 2 Cu 3 O 7-δ thin films were deposited onto (100) SrTiO 3 substrates using 1064, 532, 355, 248, and 193 nm laser ablation. Transport measurements show lower normal-state resistivities and higher critical currents in films deposited by the shorter wavelength lasers. The surface morphology of the films was rough with large particulates when the 1064 nm laser was used whereas much smoother surfaces with fewer and smaller particulates were obtained with the UV lasers. It is suggested that the better film quality obtained when the UV lasers are used is due to a small absorption depth of the UV photons in the ceramic target and to higher absorption by the ablated fragments. This leads to smaller ablated species and further fragmentation in the hotter plume and, therefore, to smoother and denser films

Infrared refractive index of thin YBa2Cu3O7 superconducting films

International Nuclear Information System (INIS)

Zhang, Z.M.; Choi, B.I.; Le, T.A.; Flik, M.I.; Siegal, M.P.; Phillips, J.M.

1992-01-01

This work investigates whether thin-film optics with a constant refractive index can be applied to high-T c superconducting thin films. The reflectance and transmittance of YBa 2 Cu 3 O 7 films on LaAlO 3 substrates are measured using a Fourier-transform infrared spectrometer at wavelengths from 1 to 100 μm at room temperature. The reflectance of these superconducting films at 10K in the wavelength region from 2.5 to 25 μm is measured using a cryogenic reflectance accessory. The film thickness varies from 10 to 200 nm. By modeling the frequency-dependent complex conductivity in the normal and superconducting states and applying electromagnetic-wave theory, the complex refractive index of YBa 2 Cu 3 O 7 films is obtained with a fitting technique. It is found that a thickness-independent refractive index can be applied even to a 25nm film, and average values of the spectral refractive index for film thicknesses between 25 and 200 nm are recommended for engineering applications

Transport properties of YBa2Cu3O7/PrBa2Cu3O7 superlattices

International Nuclear Information System (INIS)

Jakob, G.; Hahn, T.; Stoelzel, C.; Tome-Rosa, C.; Adrian, H.

1992-01-01

We investigated the transport properties of high-quality YBa 2 Cu 3 O 7 /PrBa 2 Cu 3 O 7 superlattices. The exceptional structural order of the superlattices resulted in satellite peaks up to the ninth order in X-ray diffraction diagrams and high Tc values. We find high superconducting critical transport current densities j c even for ultrafine modulated superlattices which proves the existence of nearly continuous YBa 2 Cu 3 O 7 layers. The activation energy U is found to be constant or to have a linear temperatures dependence over a wide temperature range. (orig.)

Self-generated magnetic flux in YBa$_2$Cu$_3$O$_{7-x}$ grain boundaries

OpenAIRE

Mints, R. G.; Papiashvili, Ilya

2000-01-01

Grain boundaries in YBa$_2$Cu$_3$O$_{7-x}$ superconducting films are considered as Josephson junctions with a critical current density $j_c(x)$ alternating along the junction. A self-generated magnetic flux is treated both analytically and numerically for an almost periodic distribution of $j_c(x)$. We obtained a magnetic flux-pattern similar to the one which was recently observed experimentally.

Structural and pinning properties of Y2Ba4CuMOy (M = Nb,Zr)/YBa2Cu3O7-δ quasi-multilayers fabricated by off-axis pulsed laser deposition

International Nuclear Information System (INIS)

Reich, E; Thersleff, T; Huehne, R; Iida, K; Schultz, L; Holzapfel, B

2009-01-01

Power applications based on YBa 2 Cu 3 O 7-δ coated conductors demand an enhancement of the critical current density J c in magnetic fields to be achieved using artificial pinning centres. A well-known approach to studying pinning by second phase nanoparticles is based on quasi-multilayer deposition of YBa 2 Cu 3 O 7-δ (Y123) and a dopant material. In this study we use the Y 2 Ba 4 CuMO y (M = Nb, Zr; M2411) phase as a dopant material, which proved to be very successful in increasing J c for bulk samples. Although stability of the M2411 phase in bulk Y123 has been reported, experimental evidence of its stability in thin films is still lacking. We found that during the quasi-multilayer deposition, yttrium doped Ba(M 1-x Y x )O 3 forms instead of the M2411 secondary phase, and this causes an increase of J c at high magnetic fields as well as an increase in the irreversibility field below 80 K as compared against pure Y123 thin films.

Improving chemical solution deposited YBa 2Cu 3O 7- δ film properties via high heating rates

Science.gov (United States)

Siegal, M. P.; Dawley, J. T.; Clem, P. G.; Overmyer, D. L.

2003-12-01

The superconducting and structural properties of YBa 2Cu 3O 7- δ (YBCO) films grown from chemical solution deposited (CSD) metallofluoride-based precursors improve by using high heating rates to the desired growth temperature. This is due to avoiding the nucleation of undesirable a-axis grains at lower temperatures, from 650 to 800 °C in p(O 2)=0.1%. Minimizing time spent in this range during the temperature ramp of the ex situ growth process depresses a-axis grain growth in favor of the desired c-axis orientation. Using optimized conditions, this results in high-quality YBCO films on LaAlO 3(1 0 0) with Jc(77 K) ∼ 3 MA/cm 2 for films thicknesses ranging from 60 to 140 nm. In particular, there is a dramatic decrease in a-axis grains in coated-conductors grown on CSD Nb-doped SrTiO 3(1 0 0) buffered Ni(1 0 0) tapes.

Epitaxial growth of textured YBa2Cu3O7-δ films on silver

International Nuclear Information System (INIS)

Liu Dan-Min; Liu Wei-Peng; Suo Hong-Li; Zhou Mei-Ling

2005-01-01

YBa 2 Cu 3 O 7-δ (YBCO) films were deposited on (100), (110) and (111) oriented silver single crystals and {100} left angle 100 right angle, {110} left angle 211 right angle, {110} left angle 100 right angle +{110} left angle 011 right angle {110} left angle 011 right angle and {012} left angle 100 right angle textured Ag substrates using pulsed laser deposition. The relationship between the epitaxial growth YBCO film and silver substrate has been determined. It is shown that among polycrystalline Ag substrates, {110} left angle 011 right angle textured tape is suitable for the deposition of YBCO thin films having strong texture. (orig.)

Characterization and in situ fluorescence diagnostic of the deposition of YBa2Cu3O7-x thin films by pseudo-spark electron beam ablation

International Nuclear Information System (INIS)

Jiang, Q.D.; Matacotta, F.C.; Masciarelli, G.; Fuso, F.; Arimondo, E.; Sandrin, G.

1992-12-01

The pseudo-spark electron beam ablation (PSA) technique is a comparatively simple and inexpensive method to deposit thin films of oxide materials. The effect of the electron beam power density on the efficiency of the PSA is studied. Results concerning the optimization of the deposition process of high quality superconducting YBa 2 Cu 3 O 7-x thin films on single crystal SrTiO 3 substrates are reported. Correlation between processing parameters and superconducting properties of the thin films are presented: in particular, the effects of the break-down voltage of the pseudo-spark and geometrical arrangement of the target-substrate-beam system on the T c of the resulting films. In situ spectral analysis of the radiative emission from the plasma plume has been performed at different distances from the surface of the target and at different break-down voltages of the pseudo-spark. The role of the oxygen pressure in the PSA process, which could be one order of magnitude less than that for a typical laser ablation system, is discussed. (author). 17 refs, 7 figs, 1 tab

Dominant pinning mechanisms in YBa2Cu3O7-x films on single and polycrystalline yttria stabilized zirconia substrates

Science.gov (United States)

Harshavardhan, K. S.; Rajeswari, M.; Hwang, D. M.; Chen, C. Y.; Sands, T.; Venkatesan, T.; Tkaczyk, J. E.; Lay, K. W.; Safari, A.

1992-04-01

Critical-current densities have been measured in YBa2Cu3O7-x films deposited on (100) yttria stabilized zirconia (YSZ) and polycrystalline YSZ substrates as a function of temperature (4.5-88 K), magnetic field (0-1 T) and orientation relative to the applied field. The results indicate that in films on polycrystalline substrates, surface and interface pinning play a dominant role at high temperatures. In films on (100) YSZ, pinning is mainly due to intrinsic layer pinning as well as extrinsic pinning associated with the interaction of the fluxoids with point defects and low energy planar (2D) boundaries. The differences are attributed to the intrinsic rigidity of single fluxoids which is reduced in films on polycrystalline substrates thereby weakening the intrinsic layer pinning.

Fractional Josephson vortices at YBa$_2$Cu$_3$O$_{7-x}$ grain boundaries

OpenAIRE

Mints, R. G.; Papiashvili, Ilya

2001-01-01

We report numerical simulations of magnetic flux patterns in asymmetric 45$^{\\circ}$ [001]-tilt grain boundaries in YBa$_2$Cu$_3$O$_{7-x}$ superconducting films. The grain boundaries are treated as Josephson junctions with the critical current density $j_c(x)$ alternating along the junctions. We demonstrate the existence of Josephson vortices with fractional flux quanta for both periodic and random $j_c(x)$. A method is proposed to extract fractional vortices from experimental flux patterns.

Raman spectroscopic investigation of superconducting YBa2Cu3O7/sub -//sub x/, semiconducting YBa2Cu3O6/sub +//sub x/, and possible impurity phases

International Nuclear Information System (INIS)

Mascarenhas, A.; Geller, S.; Xu, L.C.; Katayama-Yoshida, H.; Pankove, J.I.; Deb, S.K.

1988-01-01

A Raman spectroscopic investigation of specimens of superconducting YBa 2 Cu 3 O/sub 7-//sub x/ and of the possible impurity phases YBa 2 Cu 3 O/sub 6+//sub x/ (semiconductor), Y 2 BaCuO 5 , Y 2 Cu 2 O 5 , BaCuO 2 , CuO, Y 2 O 3 , and BaCO 3 indicates that in the range 100--700 cm -1 , there are six characteristic lines belonging to the superconductor. At 13 K, these lines are at 150, 338, 441, 507, 590, and 644 cm -1 . Comparison of the Raman spectra of the superconductor and the semiconductor indicates a mode stiffening of the pair at 338 and 441 cm -1 , but a mode softening of the pair at 507 and 590 cm -1 . A factor group analysis leads to a tentative assignment of the Raman and infrared allowed modes

High Tc screen-printed YBa2Cu3O(7-x) films - Effect of the substrate material

Science.gov (United States)

Bansal, Narottam P.; Simons, Rainee N.; Farrell, D. E.

1988-08-01

Thick films of YBa2Cu3O(7-x) have been deposited on highly polished alumina, magnesia spinel, nickel aluminum titanate (Ni-Al-Ti), and barium tetratitanate (Ba-Ti) substrates by the screen printing technique. Properties of the films were found to be highly sensitive to the choice of the substrate material. The film on Ba-Ti turned green after firing, due to a reaction with the substrate and were insulating. A film on Ni-Al-Ti had a Tc (onset) of about 95 K and lost 90 percent of its resistance by about 75 K. However, even at 4 K it was not fully superconducting, possibly due to a reaction between the film and the substrate and interdiffusion of the reaction products. The film on alumina had Tc (onset) of about 96 K, Tc (zero) of about 66 K, and Delta Tc of about 10 K. The best film was obtained on spinel and had Tc (onset) of about 94 K, zero resistance at 81 K, and a transition width of about 7 K.

Microstructure of epitaxial YBa2Cu3O7-x thin films grown on LaAlO3 (001)

International Nuclear Information System (INIS)

Hsieh, Y.; Siegal, M.P.; Hull, R.; Phillips, J.M.

1990-01-01

We report a microstructural investigation of the epitaxial growth of YBa 2 Cu 3 O 7-x (YBCO) thin films on LaAlO 3 (001) substrates using transmission electron microscopy (TEM). Epitaxial films grow with two distinct modes: c epitaxy (YBCO) single crystal with the c (axis normal to the surface and a epitaxy (YBCO) single crystal with the c axis in the interfacial plane), where c epitaxy is the dominant mode grown in all samples 35--200 nm thick. In 35 nm YBCO films annealed at 850 degree C, 97±1% of the surface area is covered by c epitaxy with embedded anisotropic a-epitaxial grains. Quantitative analysis reveals the effect of film thickness and annealing temperature on the density, grain sizes, areal coverages, and anisotropic growth of a epitaxy

Rheology of YBa2Cu3O7-x precursors

International Nuclear Information System (INIS)

Green, T.M.; Akinc, M.

1992-01-01

Nitrate and acetate precursors to YBa 2 Cu 3 O 7-x (123) are prepared using a molten salt technique. The viscosity and shear stress of the paste are controlled by evaporation of water from the paste. The pastes contain ∼ 20--80 vol % solids. Rheometry over strain rates of 0--200 sec -1 shows both systems are shear-thinning. Both systems are thixotropic. The nitrate system may be described by a two-stage Bingham Plastic model, the acetate by a Hershel-Bulkley model. The existence of more than one region of flow behavior suggests that there are at least two mechanisms which contribute to flow. In the low strain rate region, flow resistance is due to the existence of flocs in the colloidal assembly. At higher strain rates, flow is probably controlled by interlaminar drag interactions. Precursors produced by both methods have been used to form fibers of YBa 2 Cu 3 o 7-x , by ram extrusion

Preparation of epitaxial YBa2Cu3O7-y films on CeO2-buffered yttria-stabilized zirconia substrates by fluorine-free metalorganic deposition

International Nuclear Information System (INIS)

Tsukada, Kenichi; Yamaguchi, Iwao; Sohma, Mitsugu; Kondo, Wakichi; Kamiya, Kunio; Kumagai, Toshiya; Manabe, Takaaki

2007-01-01

Epitaxial YBa 2 Cu 3 O 7-y (YBCO) films of 120-550 nm thickness have been prepared by fluorine-free metalorganic deposition using a metal acetylacetonate-based coating solution on yttria-stabilized zirconia (YSZ) substrates with an evaporated CeO 2 buffer layer. The YBCO films were highly (0 0 1)-oriented by X-ray diffraction θ-2θ scanning and φ scanning. The YBCO films 120-400 nm in thickness demonstrated high critical current densities (J c ) with an average in excess of 3 MA/cm 2 at 77 K using an inductive method. In particular, a 210-nm-thick film showed a J c of 4.5 MA/cm 2 . These excellent properties are attributed to the high crystallinity, small in-plane fluctuation due to high epitaxy and to the microstructure free from grain boundaries in the YBCO films. Further increase of film thickness increased the fraction of irregularities, i.e., precipitates and micropores, in the film surfaces, resulting in lower J c values

Subharmonic gap structure in the characteristics of YBa2Cu3O7-x microbridges

International Nuclear Information System (INIS)

Pogrebnyakov, A.V.; Levinsen, M.T.; Sheng, Y.Q.; Freltoft, T.

1996-01-01

The subharmonic gap structures corresponding to large, 2Δ 1 =48 meV, and small, 2Δ 2 =10.3 meV, components of the energy gap were observed in the first derivatives of the current-voltage characteristics of YBa 2 Cu 3 O 7-x epitaxial thin film microbridges. The appearance of the subharmonic gap structures is attributed to Andreev reflection. (orig.)

Yttrium-enriched YBa₂Cu₃O_x thin films for coated conductors fabricated by pulsed laser deposition

DEFF Research Database (Denmark)

Khoryushin, Alexey V.; Mozhaev, Peter B.; Mozhaeva, Julia E.

2013-01-01

The effects of excess yttria on the structural and electrical properties of the YBa2Cu3Ox (YBCO) thin films are studied. The films were deposited on (LaAlO3)0.3–(Sr2AlTaO8)0.7 substrates by pulsed laser ablation from targets with different elemental composition. An increase of yttrium content of ...

The growth of large-area superconducting YBa2Cu3O7-x thin films by pulsed laser ablation

International Nuclear Information System (INIS)

Lai, H.C.; Chang, C.M.; Lin, R.J.; Liu, R.S.

1996-01-01

In-situ growth of 2-in. diameter superconducting YBa 2 Cu 3 O 7-x (YBCO) thin films using an excimer KrF pulsed laser has been studied. Films with critical transition temperature (T c,0 ) of 89±1 K and critical current density (J c,77K ) in excess of 1 x 10 6 A cm -2 have been prepared routinely. Uniformity in film thickness of below ±15% and film composition of ±5% have been measured. The effects of gas nozzle geometry and target evolution during ablation on the superconducting properties and surface morphology of YBCO thin films have also been investigated. (orig.)

Josephson spectroscopy of terahertz losses in [100]-tilt YBa2Cu3O7-x bicrystal junctions

International Nuclear Information System (INIS)

Divin, Y; Lyatti, M

2008-01-01

Terahertz losses in the [100]-tilt YBa 2 Cu 3 O 7-x grain-boundary junctions were studied using admittance Josephson spectroscopy. The I-Vcurves of the [100]-tilt YBa 2 Cu 3 O 7-x junctions, when annealed in atomic oxygen, were described by the resistively shunted junction model (RSJ) with an accuracy of better than 0.5% at the temperature range, where the characteristic voltage I c R n n -1 . At low temperatures, where I c R n >> kT/2e, the absorption of Josephson radiation by optical phonon modes in YBa 2 Cu 3 O 7-x was found to be reflected in the I-V curve of the [100]-tilt junctions. The most prominent structure is situated at the voltages V ∼ 9.5 mV, which gives the corresponding Josephson frequency of 4.6 THz in good agreement with the frequency of the strongest IR active optical phonon mode in YBa 2 Cu 3 O 7-x . Assignment of additional lines in the derived losses is discussed according to available data on lattice dynamic calculations and experimental data for a dynamic conduction Reσ 1 (f) of YBa 2 Cu 3 O 7-x . Josephson spectroscopy might be useful for study of low-energy excitations in high-T c materials

Deposition, characterization, and electronic applications of YBa2Cu3O7 thin films

International Nuclear Information System (INIS)

Kromann, R.

1992-09-01

YBa 2 Cu 3 O 7 thin films were deposited by rf sputtering and laser ablation. In the case of rf sputtering the presence of negative oxygen ions was found to give rise to severe resputtering effects. In contrast, laser ablation is found to be a much simpler and more reliable depostion method. Structural characterization in the form of an X-ray diffraction study of the structure of laser ablated YBCO thin films is reported. Two films on MgO differing by 75% in the critical current density were examined. The difference was ascribed to the fact that about 5% of the grains in the low J c film grow 45 deg. misoriented with respect to the dominant orientation in the a-b plane. Two other films on SrTiO 3 differing by 70% in J c were examined. Various ways of achieving a 45 deg. grain boundary by a biepitaxial process on MgO substrates are described. The grain boundary junctions are used to fabricate DC SQUIDs. It is demonstrated that the SQUIDs exhibit critical current modulation in a magnetic field at temperatures up to 80 K. It is shown that the 1/f noise can be reduced by a factor of 3 by the double modulation technique, indicating that the dominant contribution to the 1/f noise comes from critical current fluctuations. The high level of 1/f noise from critical current fluctuations is ascribed to the nature of the 45 deg. grain boundary and it is argued that it is necessary to develop a bi-epitaxial process for grain boundaries with angles less than 45 deg.. Finally, it is demonstrated that a SQUID and a flux transformer can be fabricated on the same substrate to form an integrated magnetometer. (au) (8 tabs., 58 ills., 97 refs.)

Femtosecond optical detection of quasiparticle dynamics in high-Tc YBa2Cu3O7-δ superconducting thin films

International Nuclear Information System (INIS)

Han, S.G.; Vardeny, Z.V.; Wong, K.S.; Symko, O.G.; Koren, G.

1990-01-01

Femtosecond dynamics of photogenerated quasiparticles in YBa 2 Cu 3 O 7-δ superconducting thin films shows, at T≤T c , two main electronic processes: (i) quasiparticle avalanche production during hot-carrier thermalization, which takes about 300 fsec; (ii) recombination of quasiparticles to form Cooper pairs, which is completed within 5 psec. In contrastr, nonsuperconducting epitaxial films such as PrBa 2 Cu 2 O 7 and YBa 2 Cu 3 O 6 show regular picosecond electronic response

Rapid processing method for solution deposited YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} thin films

Energy Technology Data Exchange (ETDEWEB)

Dawley, J.T.; Clem, P.G.; Boyle, T.J.; Ottley, L.M.; Overmyer, D.L.; Siegal, M.P

2004-02-01

YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films, deposited on buffered metal substrates, are the primary candidate for second-generation superconducting (SC) wires, with applications including expanded power grid transmission capability, compact motors, and enhanced sensitivity magnetic resonance imaging. Feasibility of manufacturing such superconducting wires is dependent on high processing speed, often a limitation of vapor and solution-based YBCO deposition processes. In this work, YBCO films were fabricated via a new diethanolamine-modified trifluoroacetic film solution deposition method. Modifying the copper chemistry of the YBCO precursor solution with diethanolamine enables a hundredfold decrease in the organic pyrolysis time required for MA/cm{sup 2} current density (J{sub c}) YBCO films, from multiple hours to {approx}20 s in atmospheric pressure air. High quality, {approx}0.2 {mu}m thick YBCO films with J{sub c} (77 K) values {>=}2 MA/cm{sup 2} at 77 K are routinely crystallized from these rapidly pyrolyzed films deposited on LaAlO{sub 3}. This process has also enabled J{sub c} (77 K)=1.1 MA/cm{sup 2} YBCO films via 90 m/h dip-coating on Oak Ridge National Laboratory RABiTS textured metal tape substrates. This new YBCO solution deposition method suggests a route toward inexpensive and commercializable {approx}$10/kA m solution deposited YBCO coated conductor wires.

Interactions in YBa2Cu3O7-x aqueous suspensions

International Nuclear Information System (INIS)

Dusoulier, Laurent; Cloots, Rudi; Vertruyen, Benedicte; Garcia-Fierro, Jose L.; Moreno, Rodrigo; Ferrari, Begona

2009-01-01

Surface charging mechanism of YBa 2 Cu 3 O 7-x (YBCO) particles in water has been investigated in order to understand their colloidal behaviour and stabilise concentrated suspensions. A broad study relating the suspension parameters (pH and zeta potential) vs. the conditions of the suspension performance (atmosphere and time) has been shown and discussed. The zeta potential values remain positive in all the pH range for the highest powder concentration studied (10 g l -1 ), evidencing a large influence of the solid content in the particle charge. The chemistry of YBa 2 Cu 3 O 7-x in water has been studied through the chemical analysis of the supernatant by inductively coupled plasma (ICP), and the surface analysis of the particles by X-ray diffraction analysis (XRD) and X-ray photoelectron spectroscopy (XPS). The presence of BaCO 3 , CuO, and the hydrolysed Ba species, such as Ba(OH) 2 and Ba(OH) + , at the particles surface has been evaluated as a function of the powder concentration. Based on these analyses, the dependence of the colloidal behaviour of YBCO on the presence of Ba soluble species has been determined. A stabilisation mechanism for YBCO particles in aqueous suspension focus on the powders deleterious minimization was proposed.

Anisotropic strain in YBa2Cu3O7-δ films analysed by deconvolution of two-dimensional intensity data

International Nuclear Information System (INIS)

Broetz, J.; Fuess, H.

2001-01-01

The influence of the instrumental resolution on two-dimensional reflection profiles of epitaxic YBa 2 Cu 3 O 7-δ films on SrTiO 3 (001) has been studied in order to investigate the strain in the superconducting films. The X-ray diffraction intensity data were obtained by two-dimensional scans in reciprocal space (q-scan). Since the reflection broadening caused by the apparatus differs for each position in reciprocal space, a highly crystalline substrate was used as a standard. Thus it was possible to measure a standard very close to the YBa 2 Cu 3 O 7-δ reflections in reciprocal space. The two-dimensional deconvolution of reflections by a new computer program revealed an anisotropic strain of the two twinning systems of the film. (orig.)

Inducing self-assembly of Y2BaCuO5 nanoparticles via Ca-doping for improved pinning in YBa2Cu3O7-x

International Nuclear Information System (INIS)

Barnes, P.N.; Haugan, T.J.; Baca, F.J.; Varanasi, C.V.; Wheeler, R.; Meisenkothen, F.; Sathiraju, S.

2009-01-01

Different mechanisms may exists as a means to provide additional or specialized enhancement of existing nanoparticulate pinning in YBa 2 Cu 3 O 7-x (YBCO) thin films. In the particular case of Y 2 BaCuO 5 (Y211) nanoparticles, Ca-doping of these nanoparticles via addition to the Y211 target material provides an additional increase to the J c (H). YBCO + Y211 samples were created by pulsed laser deposition with alternating targets of YBCO with Y211 and Y211 doped with Ca. Initial indications suggest that this improvement in pinning results from some scattered short-ranged self-assembly of the nanoparticles into short nanocolumns.

Substrate decoration for improvement of current-carrying capabilities of YBa₂Cu₃O_x thin films

DEFF Research Database (Denmark)

Khoryushin, Alexey; Mozhaev, Peter; Mozhaeva, Julia

2013-01-01

The effects of substrate decoration with yttria and Y:ZrO2 on the structural and electrical properties of the YBa2Cu3Ox (YBCO) thin films are studied. The films were deposited on (LaAlO3)3–(Sr2AlTaO8)7 substrates by pulsed laser deposition. Two different structures of decoration layer were applie...

Epitaxial films of YBa2Cu3O/sub 7-//sub δ/ on NdGaO3, LaGaO3, and SrTiO3 substrates deposited by laser ablation

International Nuclear Information System (INIS)

Koren, G.; Gupta, A.; Giess, E.A.; Segmueller, A.; Laibowitz, R.B.

1989-01-01

Frequency-doubled Nd:YAG laser (532 nm) pulses of 1.7 J/cm 2 and 10 ns duration were used to deposit thin films of YBa 2 Cu 3 O/sub 7-//sub δ/ by laser ablation on NdGaO 3 , LaGaO 3 , and SrTiO 3 substrates held at 725 +- 5 0 C in 0.2 Torr of O 2 ambient. Electrical resistivities versus temperature of all films show normal metallic behavior and sharp superconducting transitions with T/sub c/ (R = 0) at 92--93 K. Critical current densities in 0.3--0.6 μm thick, 200 μm long, and 10--30 μm wide strips were measured to be 10 6 A/cm 2 at 60, 77, and 80 K in the films on LaGaO 3 , NdGaO 3 , and SrTiO 3 , respectively. X-ray diffraction patterns show that all films grew epitaxially, with domains of only two crystalline orientations rotated 90 0 with respect to each other in the a-b plane (consistent with twins), and the c axis perpendicular to the substrates. The closely matched lattice constants of the film and substrates (0.8--2.1%) result in epitaxial growth of the films

Transformational dynamics of BZO and BHO nanorods imposed by Y2O3 nanoparticles for improved isotropic pinning in YBa2Cu3O7 -δ thin films

Science.gov (United States)

Gautam, Bibek; Sebastian, Mary Ann; Chen, Shihong; Shi, Jack; Haugan, Timothy; Xing, Zhongwen; Zhang, Wenrui; Huang, Jijie; Wang, Haiyan; Osofsky, Mike; Prestigiacomo, Joseph; Wu, Judy Z.

2017-07-01

An elastic strain model was applied to evaluate the rigidity of the c-axis aligned one-dimensional artificial pinning centers (1D-APCs) in YBa2Cu3O7-δ matrix films. Higher rigidity was predicted for BaZrO3 1D-APCs than that of the BaHfO3 1D-APCs. This suggests a secondary APC doping of Y2O3 in the 1D-APC/YBa2Cu3O7-δ nanocomposite films would generate a stronger perturbation to the c-axis alignment of the BaHfO3 1D-APCs and therefore a more isotropic magnetic vortex pinning landscape. In order to experimentally confirm this, we have made a comparative study of the critical current density Jc (H, θ, T) of 2 vol.% BaZrO3 + 3 vol.%Y2O3 and 2 vol.%BaHfO3 + 3 vol.%Y2O3 double-doped (DD) YBa2Cu3O7-δ films deposited at their optimal growth conditions. A much enhanced isotropic pinning was observed in the BaHfO3 DD samples. For example, at 65 K and 9.0 T, the variation of the Jc across the entire θ range from θ=0 (H//c) to θ=90 degree (H//ab) is less than 18% for BaHfO3 DD films, in contrast to about 100% for the BaZrO3 DD counterpart. In addition, lower α values from the Jc(H) ˜ H-α fitting were observed in the BaHfO3 DD films in a large θ range away from the H//c-axis. Since the two samples have comparable Jc values at H//c-axis, the improved isotropic pinning in BaHfO3 DD films confirms the theoretically predicted higher tunability of the BaHfO3 1D-APCs in APC/YBa2Cu3O7-δ nanocomposite films.

Out-of-substrate plane orientation control of thin YBa2Cu3O x films on NdGaO3 tilted-axes substrates

International Nuclear Information System (INIS)

Mozhaev, Peter B.; Mozhaeva, Julia E.; Bdikin, Igor K.; Kotelyanskii, Iosif M.; Lusanov, Valery A.; Hansen, Jorn Bindslev; Jacobsen, Claus S.; Kholkin, Andrey L.

2006-01-01

Epitaxial heterostructures YBa 2 Cu 3 O x (YBCO)/CeO 2 /NdGaO 3 were prepared on tilted-axes NdGaO 3 substrates using laser ablation technique. Morphology, crystal structure and electrical properties of the obtained films were characterized. The seeding mechanisms are affected by the tilt angle, resulting in superior YBCO films on NdGaO 3 substrates in an intermediate range of tilt angles of 6-14 o . The introduction of CeO 2 layer leads to change of the YBCO film orientation: at low deposition rate c-oriented films are formed, while at high deposition rates the film grows with c-axis tilted along the [1 1 0] NdGaO 3 direction. Bi-epitaxial films and structures were prepared by removal of part of the CeO 2 layer using ion-beam milling

Studies on Ba(2)YNbO(6) Buffer Layers for Subsequent YBa(2)Cu(3)O(7-x) Film Growth

National Research Council Canada - National Science Library

Sathiraju, Srinivas; Barnes, Paul N; Varanasi, Chakrapani; Wheeler, Robert

2004-01-01

In this paper, we are reporting a dielectric oxide buffer Ba(2)YNbO(6) (BYNO) and its performance on various substrates for a potential buffer layer for the growth of YBa(2)Cu(3)O(7-x) (YBCO) coated conductors. Ba(2)YNbO(6...

Transport in reversibly laser-modified YBa2Cu3O/sub 7-//sub x/ superconducting thin films

International Nuclear Information System (INIS)

Krchnavek, R.R.; Chan, S.; Rogers, C.T.; De Rosa, F.; Kelly, M.K.; Miceli, P.F.; Allen, S.J.

1989-01-01

A focused argon ion laser beam in a controlled ambient is used to modify the transport properties of superconducting YBa 2 Cu 3 O/sub 7-//sub x/ thin films. The laser-modified region shows a sharp transition temperature (T/sub c/≅76 K) that is reduced from the unmodified regions of the film (T/sub c/≅87 K). In situ monitoring of the room-temperature electrical resistance is used to control the laser processing and prevent formation of the semiconducting phase. The original properties of the superconducting film can be recovered by plasma oxidation indicating that the laser-induced phase is oxygen deficient

YBa{sub 2}Cu{sub 3}O{sub 7-x} thin films prepared by chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Apetrii, Claudia

2009-11-25

The discovery of superconductivity in ceramic materials by Bednorz and Mueller in early 1987, immediately followed by Wu et al., who showed that YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO) becomes superconducting (92 K) well above the boiling point of nitrogen (77 K) created a great excitement in superconductivity research. Potential applications of high T{sub c}-superconductors require large critical currents and high-applied magnetic fields. Effective ways to increase the critical current density at high magnetic fields in YBCO are the introduction of nanoparticles and chemical substitution of yttrium by other rare earth elements. Since low costs and environmental compatibility are essential conditions for the preparation of long length YBCO films, the cost effective chemical solution deposition (CSD) procedure was selected, given that no vacuum technology is required. To reveal the flexibility and the good optimization possibilities of the CSD approach two main processes were chosen for comparison: a fluorine-free method, namely the polymer-metal precursor technique, and a fluorine-based method, the metalorganic deposition (MOD) using the trifluoroacetates (TFA) technique. Sharp transition temperature widths {delta}T{sub c} of 1.1 K for the polymer metal method, 0.8 K for TFA method and critical current densities J{sub c} of {approx}3.5 MA/cm{sup 2} shows that high quality YBCO thin films can be produced using both techniques. Especially interesting is the magnetic field dependence of the critical current density J{sub c}(B) of the Y(Dy)BCO (80 %) films showing that for the lower magnetic fields the critical current density J{sub c}(B) is higher for a standard YBCO film, but at fields higher than 4.5 T the critical current density J{sub c}(B) of Y(Dy)BCO is larger than that for the YBCO. Above 8 T, J{sub c}(B) of the Y(Dy)BCO film is more than one order of magnitude higher than in pure YBCO film. (orig.)

Is LaAlO3 a viable substrate for the deposition of high quality thin films of YBa2Cu3O7-δ?

International Nuclear Information System (INIS)

Koren, Gad; Polturak, Emil

2002-01-01

A systematic study of the surface morphology of epitaxial thin films of YBa 2 Cu 3 O 7-δ on (100) LaAlO 3 wafers is reported. The films were prepared by high pressure dc sputtering or laser ablation deposition, on wafers of 0.5-2.8 mm thickness and 2 or 3 inch diameter. Optical and atomic force microscopy (AFM) were used to characterize the surfaces, while transport was used to verify the high quality of the films. For films prepared under the same conditions, we found a systematic increase in size and number of extended defects in the films with wafer thickness. In some cases, a clear correlation was observed between the defect structure and the twin boundaries of the LaAlO 3 substrate. We specify the conditions for minimizing these defects. (author)

Critical current density and microstructure of YBa2Cu3O7-x films as a function of film thickness

International Nuclear Information System (INIS)

Mogro-Campero, A.; Turner, L.G.; Hall, E.L.; Lewis, N.

1990-01-01

Thin films of nominal composition YBa 2 Cu 3 O 7-x (YBCO) were produced on (100) SrTiO 3 substrates by coevaporation and furnace annealing. Film thicknesses in the range of 0.2 to 2.4 μm were analyzed. Microstructural investigations by cross sectional transmission electron microscopy (TEM) reveal a continuous layer of about 0.4 μm thickness adjacent to the substrate with c-axis normal to the substrate plane. In thicker films the remaining top portion has the c-axis in the film plane. The critical current density (J c ) at 77 K decreases with increasing thickness in the thickness range exceeding 0.4 μm, qualitatively consistent with the microstructural observation, but quantitatively inconsistent with a simple model based on the microstructural data

MOCVD with gas phase composition control for the growth of high quality YBa2Cu3O7-x thin films for microwave applications

International Nuclear Information System (INIS)

Musolf, J.

1997-01-01

The MOCVD growth technique has demonstrated YBa 2 Cu 3 O 7-x thin films with adequate transport properties (T c >90 K, J c > x 10 6 A cm -2 , R s p /C v ) and the species concentrations. After determining the correlation between gas phase and solid phase composition this technique enables the reproducible growth of YBa 2 Cu 3 O 7-x thin films by MOCVD with composition very close to 123. Further refinement of growth temperature, total pressure, oxygen partial pressure and total flow rates has produced films with excellent properties. Smooth surface morphology with a low density of outgrowths ( 4 cm -2 ), narrow XRD rocking curve peaks FWHM c =92 K), low surface resistance (device R s <350 μΩ at 77 K, 10 GHz) have been demonstrated using this growth concept. Special focus was placed on optimization of the performance of a microwave test device which serves as a process control monitor of the suitability of these films for passive microwave applications. (orig.)

Transport measurements on superconducting YBa2Cu3O7-δ thin film lines

International Nuclear Information System (INIS)

Moeckly, B.H.; Lathrop, D.K.; Redinbo, G.F.; Russek, S.E.; Buhrman, R.A.

1990-01-01

Critical current densities, magnetic field response, and microwave response have been measured for laser ablated YBa 2 Cu 3 O 7-δ thin film lines on MgO and SrTiO 3 substrates. Films on SrTiO 3 have critical current densities > 1 x 10 6 A/cm 2 at 77 K and show uniform transport properties in lines of all sizes. Films on MgO have critical current densities which range between 10 2 and 10 6 A/cm 2 at 77 K and show considerable variation from device to device on the same chip. Narrow lines on MgO with low critical current densities show Josephson weak link structure which includes RSJ-like IV curves, microwave induced constant voltage steps, and a high sensitivity to magnetic field. The presence of the Josephson weak links if correlated with small amounts of misaligned grains in film on MgO

Penetration depth of YBa2Cu3O7 measured by polarised neutron reflectometry

International Nuclear Information System (INIS)

Reynolds, J.M.; Nunez, V.; Boothroyd, A.T.; Bucknall, D.G.; Penfold, J.

1998-01-01

We have applied the technique of polarised neutron reflectometry (PNR) to investigate the magnetic field profile near the surface of YBa 2 Cu 3 O 7 films at 4.3 K. The samples comprised 700-1400 nm of c-axis oriented, single crystal YBa 2 Cu 3 O 7 deposited by laser ablation on SrTiO 3 substrates. The measurements were carried out on the CRISP reflectometer at the ISIS facility. The PNR technique measures the magnetic induction profile perpendicular to the surface, and so in our case the decay of flux in the c-direction was measured with a field applied parallel to the ab plane. We present preliminary data for the polarised and unpolarised reflectivity (orig.)

Epitaxial growth of YBa2Cu3O7-δ thin films on LiNbO3 substrates

International Nuclear Information System (INIS)

Lee, S.G.; Koren, G.; Gupta, A.; Segmuller, A.; Chi, C.C.

1989-01-01

In situ epitaxial growth of YBa 2 Cu 3 O 7-δ thin films on Y-cut LiNbO 3 substrates using a standard laser ablation technique is reported. Resistance of the films shows a normal metallic behavior and a very sharp ( c (R=0) of 92 K. High critical current density of J c (77 K)=2x10 5 A/cm 2 is observed, which is in accordance with epitaxial growth. Film orientation observed from x-ray diffraction spectra indicates that the c axis is normal to the substrate plane and the a axis is at 45 degree to the [11.0] direction of the hexagonal lattice of the substrate with two domains in mirror image to the (110) plane

Magnetization studies in ceramic YBa sub 2 Cu sub 3 O sub 7-x. Issledovanie namagnichennosti v keramicheskom YBa sub 2 Cu sub 3 O sub 7-x

Energy Technology Data Exchange (ETDEWEB)

Gamtsemlidze, G A; Bibiluri, D I; Gamkrelidze, K P; Mirzoeva, M I; Sharikadze, L A; Shoniya, G K [Tbilisskij Gosudarstvennyj Univ., Tbilisi (Georgia)

1991-05-01

The behaviour of ceramic YBa{sub 2}Cu{sub 3}O{sub 7-x} sample magnetization is studied as a function of the external field, prehistory and temperature using the ballistic method. The results obtained are interpreted is terms of the vortex model.

Interface structure and electronic properties of SrTiO{sub 3} and YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} crystals and thin films

Energy Technology Data Exchange (ETDEWEB)

Thiess, S.

2007-07-01

Two new extensions of the X-ray standing wave (XSW) technique, made possible by the intense highly collimated X-ray beams from undulators at the ESRF, are described in this thesis. First, the XSW method was applied in a structural study to solve the nucleation mechanism of the high temperature superconductor YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} on the (001) surface of SrTiO{sub 3}. Second, the valence electronic structures of SrTiO{sub 3} and YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} were investigated. Finally, recent developments in the field of photoelectron spectroscopy in the hard X-ray region are described. The X-ray standing wave method is used in combination with fluorescence, Auger or photoelectron spectroscopy and lends very high spatial resolution power to these analytical techniques. Previously, the XSW method has been used for structure determination of surfaces and interfaces. The currently available X-ray intensities permit extensions to the XSW technique. Two recently established applications, described in this thesis, are XSW real space imaging and XSW valence electronic structure analysis. XSW real space imaging was employed to analyse the atomic structure of 0.5 and 1.0 layers of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} deposited on SrTiO{sub 3}(001). Three-dimensional images of the atomic distributions were reconstructed for each of the elements from experimentally determined Fourier components of the atomic distribution functions. The images confirmed the formation of a perovskite precursor phase prior to the formation of the YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} phase during the growth of the first monolayer of the film. XSW valence electronic structure analysis applied to SrTiO{sub 3} identified the valence band contributions arising from the strontium, titanium, and oxygen sites of the crystal lattice. Relations between the site-specific valence electronic structure and the lattice structure were established. The experimental results agree very well with

Macro and micro Raman spectroscopy of YBa2Cu3O7 films and microbridges

International Nuclear Information System (INIS)

Bock, A.

1993-01-01

In the present work Raman spectroscopy is used as a method to characterize the properties of YBa 2 Cu 3 O 7 -films. This is done in the usual (macro-)Raman set-up as well as in the micro-Raman set-up where the spatial resolution is about one micron. To obtain comparable results the Raman spectra have to be corrected for the spectral response of the spectrometer. Therefore a calibration of the set-up was performed. The calibration can be used to determine spot temperatures by comparing Stokes and Anti-Stokes spectra. Two different methods are developed to correct for the straylight which is additionally observed in Raman-spectra of YBa 2 Cu 3 O 7 -films. Macro- as well as micro-Raman measurements are used to characterize the film properties, where care has been taken to avoid damages by the laser itself. The macro-Raman set-up is used to identify the properties of the film, such as orientation, oxygen-content and morphology. Outgrowths and other particles on the surface are on the other hand investigated by micro-Raman spectroscopy. The surface morphology is additionally characterized by scanning-electron-microscopy. This is compared to the Raman data. Raman spectra of epitaxial YBa 2 Cu 3 O 7 -films are taken as a function of the temperature and exciting wavelength. The influence on the phonons and on the electronic background is discussed separately. The obtained results are analyzed by comparison with single-crystal measurements. The investigation of YBa 2 Cu 3 O 7 -microbridges in the macro-Raman set-up allows a correlation between the local optical and electrical properties of the bridge. A method is presented which can account for the heating in the laser spot with high accuracy. This method allows to determine local critical current densities as well as local critical temperatures on the microbridge. It provides also the possibility to take Raman spectra at precise spot temperatures. (orig./WL)

Scaling properties of YBa{sub 2}Cu{sub 3}O{sub x} films

Energy Technology Data Exchange (ETDEWEB)

Arushanov, E [Institute of Applied Physics, Academy of Sciences of the Moldova Republic, Academie street 5, Chisinau, MD 2028 (Moldova, Republic of); Levcenko, S [Institute of Applied Physics, Academy of Sciences of the Moldova Republic, Academie street 5, Chisinau, MD 2028 (Moldova, Republic of); Alami, H El [GPMD-Universite Paris 12, 61 avenue De Gaulle, 94010 CRETEIL Cedex (France); Cavellin, C Deville [GPMD-Universite Paris 12, 61 avenue De Gaulle, 94010 CRETEIL Cedex (France)

2005-11-01

An alternative simple method is proposed for analysing the scaling properties of the high-T{sub c} superconductor cuprates. The temperature is rescaled with a parameter T{sub R} determined from the precise analysis of R{sub H}(1/T), where R{sub H} is the Hall coefficient, in the high-temperature range. To illustrate this new method, the resistivity and Hall effect data obtained on underdoped YBa{sub 2}Cu{sub 3}O{sub x} epitaxial thin films are analysed. It is shown that the temperature-dependent resistivity {rho}(T), Hall coefficient R{sub H}(T) and the cotangent of the Hall angle cot {theta}{sub H}(T) of underdoped YBa{sub 2}Cu{sub 3}O{sub x} can be scaled into universal curves using this parameter T{sub R} to make a linear transformation of temperature and {rho}(T), R{sub H}(T) or cot{theta}{sub H}(T)

Positron annihilation in thermally quenched YBa2Cu3O7-x

International Nuclear Information System (INIS)

Hong Zhang; Xiao-Gang Wang; Yao-Xian Fu

1988-01-01

Trapping effects related directly with the oxygen vacancy in YBa 2 Cu 3 O 7-x are studied by the aid of positron lifetime and positron annihilation Doppler energy spectra of a thermally quenched sample. Results indicate that the trapping center is linearly related with the oxygen vacancy. Vacancies are ordered in the orthorhombic phase and disordered in the tetragonal phase on the Cu-O plane

Processing of La/sub 1.8/Sr/sub 0.2/CuO4 and YBa2Cu3O7 superconducting thin films by dual-ion-beam sputtering

International Nuclear Information System (INIS)

Madakson, P.; Cuomo, J.J.; Yee, D.S.; Roy, R.A.; Scilla, G.

1988-01-01

High quality La/sub 1.8/Sr/sub 0.2/CuO 4 and YBa 2 Cu 3 O 7 superconducting thin films, with zero resistance at 88 K, have been made by dual-ion-beam sputtering of metal and oxide targets at elevated temperatures. The films are about 1.0 μm thick and are single phase after annealing. The substrates investigated are Nd-YAP, MgO, SrF 2 , Si, CaF 2 , ZrO 2 -9% Y 2 O 3 , BaF 2 , Al 2 O 3 , and SrTiO 3 . Characterization of the films was carried out using Rutherford backscattering spectroscopy, resistivity measurements, transmission electron microscopy, x-ray diffraction, and secondary ion mass spectroscopy. Substrate/film interaction was observed in every case. This generally involves diffusion of the substrate into the film, which is accompanied by, for example, the replacement of Ba by Sr in the YBa 2 Cu 2 O 7 structure, in the case of SrTiO 3 substrate. The best substrates were those that did not significantly diffuse into the film and which did not react chemically with the film. In general, the superconducting transition temperature is found to depend on substrate temperature and ion beam energy, film composition, annealing conditions, and the nature and the magnitude of the substrate/film interaction

The effect of YBa2Cu3O7-x powder characteristics on thick coatings prepared by atmospheric plasma spraying

International Nuclear Information System (INIS)

Georgiopoulos, E.; Tsetsekou, A.

2000-01-01

The development of superconducting YBa 2 Cu 3 O 7-x plasma sprayed coatings on metal substrates can be very useful for applications such as targets for thin-film deposition techniques (sputtering, laser ablation, ion assisted deposition) or magnetic shielding, due to the brittle nature of bulk superconductors. The plasma spraying technique is very flexible and can be used for manufacturing components with a large variety of geometries. This technique requires the use of powders with good rheological characteristics. In this study, YBa 2 Cu 3 O 7-x powders were produced by using the conventional solid-state reaction route and also by spray drying a solution of nitrate precursors. Both powders, as well as mixtures of them, were plasma sprayed to develop coatings on stainless-steel substrates, with the aim of studying the effect of the feedstock powder characteristics on the coating properties. It was found that by optimizing the plasma spraying conditions, good quality coatings could be obtained. However, the powder morphology and homogeneity significantly affect the coating quality. More homogeneous powders lead to better results, the spray-dried powder being the best because of its enhanced rheological properties and good morphology. (author)

The effects of H+ implants on YBa2Cu3O7 superconducting materials

International Nuclear Information System (INIS)

Luo Chenglin; Pan Guoqiang; Han Ming; Wang Guanghou

1993-09-01

The variations of microstructure and electrical properties of Y-Ba-Cu O with and without H + implantation have been studied by scanning electron microscope, X-ray diffraction and IR spectrum techniques. The results have shown that these variations are directly relative to the intrinsic quality of YBa 2 Cu 3 O 7 . Microstructural change is responsible for the variations of electrical properties of YBa 2 Cu 3 O 7 superconductor. The Cu H bond formed by H + implanted into YBa 2 Cu 3 O 7 is not a key factor for these variations

Synthesis of in-plane aligned a-axis YBa2Cu3O7-δ thin films

International Nuclear Information System (INIS)

Young, K.H.; Sun, J.Z.

1991-01-01

We report the successful synthesis of superconducting YBa 2 Cu 3 O 7-δ (YBCO) (100) thin films with alignment of the in-plane c axis. These films were grown on single crystal NdGaO 3 (110) substrates. The twofold symmetry of the substrate surface is believed to lead to anisotropic alignment of the in-plane c axis of the epitaxial YBCO (100) film. X-ray diffraction studies indicate that over 80% of the film grew epitaxially with the YBCO [100] perpendicular to the substrate surface, and YBCO [001] aligned along one pseudo-cubic axis of the NdGaO 3 . The superconductivity onset of the film was measured to be 89 K by ac susceptibility

Epitaxial solution deposition of YBa2Cu3O7-6 coated conductors.

Energy Technology Data Exchange (ETDEWEB)

Overmyer, Donald L.; Clem, Paul Gilbert; Siegal, Michael P.; Holesinger, Terry A. (Los Alamos National Laboratory, Los Alamos, NM); Voigt, James A.; Richardson, Jacob J.; Dawley, Jeffrey Todd

2004-11-01

A variety of solution deposition routes have been reported for processing complex perovskite-based materials such as ferroelectric oxides and conductive electrode oxides, due to ease of incorporating multiple elements, control of chemical stoichiometry, and feasibility for large area deposition. Here, we report an extension of these methods toward long length, epitaxial film solution deposition routes to enable biaxially oriented YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO)-coated conductors for superconducting transmission wires. Recent results are presented detailing an all-solution deposition approach to YBCO-coated conductors with critical current densities J{sub c} (77 K) > 1 MA/cm{sup 2} on rolling-assisted, biaxially textured, (200)-oriented Ni-W alloy tapes. Solution-deposition methods such as this approach and those of other research groups appear to have promise to compete with vapor phase methods for superconductor electrical properties, with potential advantages for large area deposition and low cost/kA {center_dot} m of wire.

Directly coupled direct current superconducting quantum interference device magnetometers based on ramp-edge Ag:YBa2Cu3O7-x/PrBa2Cu3O7-x/Ag:YBa2Cu3O7-x junctions

International Nuclear Information System (INIS)

Jia, Q.X.; Yan, F.; Mombourquette, C.; Reagor, D.

1998-01-01

Directly coupled dc superconducting quantum interference device (SQUID) magnetometers on LaAlO 3 substrates were fabricated using ramp-edge superconductor/normal-metal/superconductor junctions, where Ag-doped YBa 2 Cu 3 O 7-x was used for the electrode and PrBa 2 Cu 3 O 7-x for the normal-metal barrier. A flux noise of 8x10 -6 Φ 0 Hz -1/2 at 10 kHz measured with a dc bias current was achieved at 75 K, which corresponded to a field sensitivity of 400fTHz -1/2 for a magnetometer with a pick-up loop area of 8.5mmx7.5mm. Most significantly, the noise floor increased at lower frequencies with a frequency dependence slightly less than 1/f. The field noise of the SQUID magnetometers increased by only 25% after cycling the devices from zero field to 500 mG. In a static earth close-quote s magnetic field background, the field noise of the SQUID magnetometers increased by less than a factor of 2. copyright 1998 American Institute of Physics

Characterization of Microstructure and Performance of YBa2Cu3O7−x Films Synthesized Through Sol–Gel Aqueous Precursors with DEA/TEA Addition

DEFF Research Database (Denmark)

Tang, Xiao; He, Dong; Zhao, Yichun

2013-01-01

YBa2Cu3O7−x (YBCO) superconducting thin films are synthesized through non-fluorine sol–gel aqueous processes. Diethanolamine (DEA) and triethonalamine (TEA), which have similar molecular structures but different complexation abilities and molecular weights, are separately used as chelating agents...

Densification of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Zhou, J.P.; Sorrell, C.C.; Dou, S.X.; Liu, H.K.; Bourdillon, A.J.

1991-01-01

YBa 2 Cu 3 O 7-x is normally densified by solid-state reaction at 935deg-980deg C for 2-4 h in air or at 940deg-1000deg C for 5-10 h in flowing oxygen. Typical densities achieved these ways are 70-80% of theoretical. Rahaman et al. obtained 95% density by rapidly inserting samples in a furnace at 800deg C. Densities of 94-100% can be achieved by sinter-forging, hot pressing, and hot isostatic pressing. The present work reports a rapid sintering technique whereby 100% density can be achieved without the use of specialised equipment

Yttrium-enriched YBa{sub 2}Cu{sub 3}O{sub x} thin films for coated conductors fabricated by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Khoryushin, Alexey V., E-mail: khoryushin@ya.ru [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark); Mozhaev, Peter B.; Mozhaeva, Julia E.; Andersen, Niels H. [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark); Grivel, Jean-Claude [Department of Energy Conversion and Storage, Technical University of Denmark, DK-4000 Roskilde (Denmark); Hansen, Jørn Bindslev; Jacobsen, Claus S. [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark)

2013-02-14

Highlights: ► YBCO films were fabricated by PLD from targets of various elemental compositions. ► The Y-enriched films contain yttria nanoparticles which provide efficient pinning. ► The best film has 5.5× higher j{sub c}(5 T,50 K) = 2.6MA/cm{sup 2} comparing with a reference film. ► The Y-enriched films remain c-oriented up to 500 nm. ► Films demonstrate no j{sub c} suppression with thickness and remarkable stability with time. -- Abstract: The effects of excess yttria on the structural and electrical properties of the YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) thin films are studied. The films were deposited on (LaAlO{sub 3}){sub 0.3}–(Sr{sub 2}AlTaO{sub 8}){sub 0.7} substrates by pulsed laser ablation from targets with different elemental composition. An increase of yttrium content of the target leads to formation of porous films with significantly improved current-carrying capabilities. Structural studies of these films reveal presence of yttria nanoparticles embedded into the YBCO matrix. The highest obtained critical current density in an external magnetic field of 5 T was 2.6 MA/cm{sup 2} at 50 K and 9.4 MA/cm{sup 2} at 20 K. The fabricated Y-enriched YBCO films remain c-oriented at least up to 600 nm thickness with no significant suppression of the critical current density.

Bi-epitaxial YBa{sub 2}Cu{sub 3}O{sub x} Thin Films on Tilted-axes NdGaO{sub 3} Substrates with CeO{sub 2} Seeding Layer

Energy Technology Data Exchange (ETDEWEB)

Mozhaev, P B [Institute of Physics and Technology RAS, 117218, Moscow (Russian Federation); Mozhaeva, J E [Institute of Physics and Technology RAS, 117218, Moscow (Russian Federation); Jacobsen, C S [Technical University of Denmark, Physics Department, Lyngby, DK-2800, Denmark (Denmark); Hansen, J Bindslev [Technical University of Denmark, Physics Department, Lyngby, DK-2800, Denmark (Denmark); Bdikin, I K [CICECO, University of Aveiro, Aveiro, 3810-193 (Portugal); Luzanov, V A [Institute of Radio Engineering and Electronics, Moscow, 125009 (Russian Federation); Kotelyanskii, I M [Institute of Radio Engineering and Electronics, Moscow, 125009 (Russian Federation); Zybtsev, S G [Institute of Radio Engineering and Electronics, Moscow, 125009 (Russian Federation)

2006-06-01

Bi-epitaxial YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) thin films with out-of-plane tilt angle in the range 18 - 27{sup 0} were manufactured using pulsed laser deposition on NdGaO{sub 3} tilted-axes substrates with CeO{sub 2} seeding layers. The YBCO thin film orientation over the seeding layer depended on deposition conditions. Removal of the seeding layer from part of the substrate surface by ionbeam etching resulted in formation of a bi-epitaxial thin film with different c-axis orientation of two parts of the film. The bi-epitaxial film orientation and structure were studied using X-ray diffraction techniques, and surface morphology was observed with atomic force microscope (AFM). Photolithography and ion-beam etching techniques were used for patterning bi-epitaxial thin films. Electrical characterization of the obtained structures was performed.

Positron implantation studies of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Anwand, W.; Brauer, G.; Coleman, P.G.; Knights, A.P.; Teske, K.; Schuster, G.; Rudolph, K.

1995-01-01

Slow positron implantation spectroscopy has been applied to the study of a set of samples of superconducting YBa 2 Cu 3 O 7-x . The depth-sensitive positron response to oxygen content and preparation history is presented. An outline is given of the experimental method - solid electrolyte coulometry in carrier-gas mode - used to measure oxygen exchange for the same set of samples. (orig.)

Precipitates in YBa2Cu3O7-δ thin films annealed at low oxygen partial pressure

International Nuclear Information System (INIS)

Hou, S.Y.; Phillips, J.M.; Werder, D.J.; Tiefel, T.H.; Fleming, R.M.; Marshall, J.H.; Siegal, M.P.

1993-01-01

We have studied the precipitates in YBa 2 Cu 3 O 7-δ (YBCO) thin films grown by the BaF 2 process in p O 2 =4 Torr and 700 degree C. While stoichiometric films result in BaCuO 2 surface precipitates, we have found Y 2 Cu 2 O 5 precipitates embedded in the matrix of the same film. Off stoichiometric films with Ba/Y 2 Cu 2 O 5 in the film matrix. The estimated densities of the two precipitates favor a stoichiometric YBCO film matrix. This behavior is not explainable in terms of phase equilibria and is attributed to kinetic effects. The electrical properties of the films degrade as the Ba/Y ratio deviates from 2.00

Epitaxial YBa2Cu3O7-x nanocomposite films and coated conductors from BaMO3 (M = Zr, Hf) colloidal solutions

Science.gov (United States)

Obradors, X.; Puig, T.; Li, Z.; Pop, C.; Mundet, B.; Chamorro, N.; Vallés, F.; Coll, M.; Ricart, S.; Vallejo, B.; Pino, F.; Palau, A.; Gázquez, J.; Ros, J.; Usoskin, A.

2018-04-01

Superconducting nanocomposites are the best material choice to address the performance required in power applications and magnets working under high magnetic fields. However, it is still challenging to sort out how to achieve the highest superconducting performance using attractive and competitive manufacturing processes. Colloidal solutions have been recently developed as a novel and very promising low cost route to manufacture nanocomposite coated conductors. Well dispersed and stabilized preformance nanoparticle solutions are first prepared with high concentrations and then mixed with the YBa2Cu3O7 metalorganic precursor solutions to generate colloidal solutions to grow the nanocomposite films. Here we demonstrate, for the first time, that non-reactive BaZrO3 and BaHfO3 perovskite preformed nanoparticles are suitable for growing high quality thin and thick films, and coated conductors with a homogeneous distribution and controlled particle size using this fabrication method. Additionally, we extend the nanoparticle content of the nanocomposites up to 20%-25% mol without any degradation of the superconducting properties. Thick nanocomposite films, up to 0.8 μm, have been prepared with a single deposition of low-fluorine solutions using an ink jet printing dispenser and we demonstrate that the preformed nanoparticles display only a very limited coarsening during the growth process and so high critical current densities J c (B) under high magnetic fields. These films show the highest critical currents achieved so far based on the colloidal solution approach, I c = 220 A/cm-w at 77 K and self-field, and they still have a high potential for further increase in the film thickness. Finally, we also show that nanocomposite YBa2Cu3O7-BaZrO3 coated conductors based on an alternating beam assisted deposited YSZ buffer layer on stainless steel metallic substrates can be developed based on these novel colloidal solutions. Non-reactive preformed oxide perovskite

On the Fermi surface of YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Peter, M.; Manuel, A.A.; Hoffmann, L.; Sadowski, W.

1992-01-01

We show that the signature of a Fermi surface sheet of YBa 2 Cu 3 O 7-δ may be obtained unambiguously from twinned crystals. Comparison of electron-positron momentum density from YBa 2 Cu 3 O 7-δ measured both in insulating and (superconducting) twinned phases leads to a decisive further proof of the existence of the Fermi surface in the metallic YBa 2 Cu 3 O 7-δ . In addition, measurements on untwinned YBA 2 Cu 3 O 7-δ single crystals reveal also a ridge Fermi surface sheet attributed by band structure calculations to CuO chains. 14 refs., 3 figs

Improving chemical solution deposited YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} film properties via high heating rates

Energy Technology Data Exchange (ETDEWEB)

Siegal, M.P.; Dawley, J.T.; Clem, P.G.; Overmyer, D.L

2003-12-01

The superconducting and structural properties of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films grown from chemical solution deposited (CSD) metallofluoride-based precursors improve by using high heating rates to the desired growth temperature. This is due to avoiding the nucleation of undesirable a-axis grains at lower temperatures, from 650 to 800 deg. C in p(O{sub 2})=0.1%. Minimizing time spent in this range during the temperature ramp of the ex situ growth process depresses a-axis grain growth in favor of the desired c-axis orientation. Using optimized conditions, this results in high-quality YBCO films on LaAlO{sub 3}(1 0 0) with J{sub c}(77 K) {approx} 3 MA/cm{sup 2} for films thicknesses ranging from 60 to 140 nm. In particular, there is a dramatic decrease in a-axis grains in coated-conductors grown on CSD Nb-doped SrTiO{sub 3}(1 0 0) buffered Ni(1 0 0) tapes.

RBS and ion channeling studies of Ag-doped YBa2Cu3O7-δ targets and films

International Nuclear Information System (INIS)

Li Yupu; Liu, J.R.; Cui, X.T.; Chu, W.K.

1998-01-01

The location of Ag in Ag-doped YBa 2 Cu 3 O 7-δ (YBCO) films and other high-T c materials (such as Ag-doped BiSrCaCuO films and Ag-sheathed textured BiSrCaCuO wires) is a very important issue for improving high-T c materials. In this work, laser ablated and DC magnetron sputtered YBCO films on (100) LaAlO 3 and (100) SrTiO 3 were prepared from sintered Ag-YBCO composite targets (nominally containing 5 wt% Ag) and studied by Rutherford backscattering spectrometry (RBS) and ion channeling techniques using 2.0 MeV 4 He + and 7 Li + beams. We have found that the Ag-YBCO targets contain about 3 wt% Ag and most of the retained Ag atoms form some small size Ag precipitates with a typical size smaller than a few microns. We have demonstrated that in very good single crystalline YBCO films, the percentage of retained Ag in substitutional sites can be estimated by ion channeling technique. For example, we have found that about 1.2 wt% Ag atoms remain in the laser ablated Ag-doped films prepared from the Ag-YBCO target and about two-thirds of the retained Ag atoms occupy substitutional sites. The sputtered films contain less retained Ag atoms since the deposition temperature is higher and deposition time is longer than those for laser ablated films. (orig.)

Temperature and depth dependence of positron annihilation parameters in YBa2Cu3O/sub 7-x/ and La/sub 1.85/Sr/sub 0.15/CuO4

International Nuclear Information System (INIS)

Lynn, K.G.; Usmar, S.G.; Nielsen, B.; van der Kolk, G.; Kanazawa, I.; Sferlazzo, P.; Moodenbaugh, A.R.

1988-01-01

The temperature dependence of the positron annihilation parameters for YBa 2 Cu 3 O/sub 7-//sub x/ x = 0.7, 0.4 and 0.0 and La/sub 1.85/Sr/sub 0.15/CuO 4 were measured. The depth dependence of the YBa 2 Cu 3 O 7 was studied using a variable-energy positron beam showing a strong depth dependence in the Doppler line-shape extending up to an average depth of ∼5.0 μm. It was found that a transition in the Doppler line-shape parameter, ''S'', was associated with the superconducting transition temperature (T/sub c/) in YBa 2 Cu 3 O/sub 7-x/ x = 0.4 and 0.0 while no transition was observed in the nonsuperconducting YBa 2 Cu 3 O/sub 6.3/. Positron lifetime parameters in YBa 2 Cu 3 O 7 were found to be consistent with positrons localized at open volume regions (probably unoccupied crystallographic sites) in this material with a lifetime of 210 psec at 300 K. These results indicate that the electron density at these unoccupied sites increases, using a free electron model, approximately 9% between 100 and 12 K

Characterization of defect modes in YBa2Cu3O7-δ thin films probed by Raman scattering

International Nuclear Information System (INIS)

Hong, Seongsik; Jo, Hyunchul; Cheong, Hyeonsik; Park, Gwangseo

2005-01-01

A Raman analysis is performed on a series of fully oxygenated YBa 2 Cu 3 O 7-δ thin films, on MgO(1 0 0) substrates, deposited by the pulsed laser technique at temperatures between 680 deg C and 820 deg C. θ - 2θ scans of the films by the X-ray diffraction show that the YBCO films are oriented in the c-axis. There are no extra peaks appearing in the X-ray diffraction data. Besides the well-known active modes, however, Raman spectra reveal a number of defect modes. The defect mode at 594 cm -1 redshifts and merges toward the O(4)-A g mode at 502 cm -1 with decreasing deposition temperatures. This mode is significantly asymmetrical and broad, whereas the mode at 243 cm -1 is symmetrical, with a small full width at half maximum remaining unchanged at a value around its own frequency. The intensity of the mode at 243 cm -1 seems to depend on the intensity of the mode at 594 cm -1 . Quantitative calculations concerning the relative intensities show that the two modes are related to each other

Solid-state interaction between nickel and YBa/sub 2/Cu/sub 3/O/sub x/

Energy Technology Data Exchange (ETDEWEB)

Champagne, B; Parent, L; Moreau, C

1989-01-01

As part of a search for suitable metals for use in composite cables made up of high-temperature superconductors in a metallic matrix, the solid-state reaction between nickel and YBa/sub 2/Cu/sub 3/O/sub x/ was studied. Green compacts of YBa/sub 2/Cu/sub 3/O/sub x/ were hot isostatically pressed (HIPed) in nickel. The microstructure, density and nature of phases present in HIPed parts were characterized. Resistivity measurements indicated that HIPed parts are not superconducting owing to the loss of oxygen and required an annealing step in oxygen for restoring superconductivity. The diffusion of nickel into YBa/sub 2/Cu/sub 3/O/sub x/ as well as the diffusion of Ba, Cu and Y into nickel was very limited. However, a thin interaction zone consisting of a nickel-rich oxide compound was formed at the Ni-YBa/sub 2/Cu/sub 3/O/sub x/ interface. The presence of such an interaction zone could have a detrimental effect on the thermal stabilization of Ni-YBa/sub 2/Cu/sub 3/O/sub x/ composite wires. 7 refs., 6 figs., 1 tab.

On a possibility of cold fusion in deuterium-saturated YBa2Cu3O7-x ceramics in superconducting state

International Nuclear Information System (INIS)

Lipson, A.G.; Sakov, D.M.; Toporov, Yu.P.; Gromov, V.V.; Deryagin, B.V.

1991-01-01

A possibility to generate neutrons by deuterated YBa 2 Cu 3 O 7-x ceramics in superconducting (T c ) and normal (T>T c ) states is studied. The presented data points to a relationship between the processes of cold nuclear fusion and high-temperature superconductivity in YBa 2 Cu 3 O 7-x pellets deuterated at T c (77< T<90 K)

Preparation of YBa2Cu3O7-x precursors from a fused eutectic of sodium and potassium hydroxides

International Nuclear Information System (INIS)

Coppa, N.; Nichols, D.H.; Schwegler, J.W.; Crow, J.E.; Myer, G.H.; Salamon, R.E.

1989-01-01

A method for preparing YBa 2 Cu 3 O 7-x from the simultaneous thermal decomposition of the nitrates of yttrium, barium, and copper in an anhydrous fused eutectic of sodium and potassium hydroxide is described. This method eliminates the need for any mechanical grinding or the introduction of carbon containing anions. Products formed are fine powders (∼1 μm) having mole ratios 1.00 Y:2.00 Ba:3.06 Cu. X-ray diffraction analysis reveal that the initial products are Y(OH) 3 , BaO 2 , and CuO, which when air calcinated/ oxygen annealed at 900--950 degree C form the superconducting YBa 2 Cu 3 O 7-x . A mechanism is postulated for product formation as a function of reaction conditions

Paramagnetic moments in YBa2Cu3O7−δ nanocomposite films

International Nuclear Information System (INIS)

Dias, F.T.; Vieira, V.N.; Silva, D.L.; Albino Aguiar, J.; Valadão, D.R.B.; Obradors, X.; Puig, T.; Wolff-Fabris, F.; Kampert, E.

2014-01-01

Highlights: • The paramagnetic Meissner effect was observed in a nanocomposite YBaCuO thin film. • The paramagnetic moments in FC experiments were observed up to 10 T. • The paramagnetic Meissner effect increases when the magnetic field is increased. • Results may be explained based on the flux compression scenario and vortex pinning. • An apparent saturation tendency of the paramagnetic moments could be observed. - Abstract: We report on magnetization studies in YBa 2 Cu 3 O 7−δ thin films with dispersed Ba 2 YTaO 6 nanoparticles. The magnetization measurements were made using a superconducting quantum interference device (SQUID) and a vibrating sample magnetometer (VSM). Magnetic moments were measured as functions temperature using zero-field cooling (ZFC) and field-cooled (FC) prescriptions for magnetic fields up to 10 T applied parallel and perpendicular to the ab planes. A paramagnetic response related to the superconducting state was observed during the FC experiments. This effect, known as paramagnetic Meissner effect (PME), apparently increases when the magnetic field is increased. We discuss our PME results in terms of the strong pinning scenario modulated by Ba 2 YTaO 6 nanoparticles dispersed into the superconducting matrix

Role of atomic oxygen in the low-temperature growth of YBa2Cu3O/sub 7-//sub δ/ thin films by laser ablation deposition

International Nuclear Information System (INIS)

Koren, G.; Gupta, A.; Baseman, R.J.

1989-01-01

Thin films of YBa 2 Cu 3 O/sub 7-//sub δ/ were deposited on (100) SrTiO 3 substrates held at 600 and 700 0 C in N 2 O and O 2 ambients using 355 nm Nd-YAG laser pulses for ablation of the target. The experiments were done either in the presence or absence of 193 nm excimer laser irradiation of the ambient gas between the target and the substrate. Results without the excimer irradiation show that in 0.2 Torr of both N 2 O and O 2 , at 700 0 C substrate surface temperature, excellent smooth films with T/sub c/ (R = 0) of 93 K and J/sub c/ (88 K) of 1.3 x 10 6 A/cm 2 were obtained. At 600 0 C, semiconducting films with no superconducting transition were obtained in O 2 ambient, whereas in N 2 O, semiconducting normal state behavior with broad superconducting transition was found. With the 193 nm irradiation, no change was observed in the electrical properties of the films deposited in O 2 at 600 0 C, whereas in N 2 O reasonably good superconducting films with normal metallic behavior and T/sub c/ (R = 0) of 84 K were found. Since the 193 nm photons hardly dissociate O 2 molecules, but very efficiently photodissociate the N 2 O molecules to form N 2 and O( 1 D), it is concluded that the atomic oxygen produced by photodissociation of N 2 O is responsible for the superconducting film deposition at 600 0 C

Observation of distinct, temperature dependent flux noise near bicrystal grain boundaries in YBa2Cu3O7-x films

DEFF Research Database (Denmark)

Bukh, K. R.; Jacobsen, Claus Schelde; Hansen, Jørn Bindslev

2000-01-01

The characteristics of the magnetic flux noise in high temperature superconducting thin-films of yttrium-barium-copper-oxide (YBa2Cu3O7) in the vicinity of artificial grain boundaries have been studied by means of a low critical temperature superconducting quantum interference device (SQUID...

Secondary phase formation in YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} thin films and YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}/SrTiO{sub 3} superlattices

Energy Technology Data Exchange (ETDEWEB)

Johnson, C.N.L.

1996-06-01

Studies of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) thin films and YBCO/STO superlattices has been performed. The dc magnetron sputtered YBCO single layer investigation concerned the dependence of the secondary phase formation and superconducting transport properties on sputtering target and ambient gas composition. YBCO/STO superlattices, grown by dc and rf magnetron sputtering, respectively, were analyzed with respect to microstructure and formation of secondary phases. The main characterization techniques used in this study have been x-ray diffraction to identify phases and to obtain orientational relationships, scanning electron microscopy to study surface morphology, transmission electron microscopy for microstructural characterization, and energy-dispersive x-ray spectroscopy for chemical characterization. With the aim to reduce or avoid the formation of copper-rich surface particles and still maintain satisfactory superconducting transport properties, YBCO films were deposited using copper-poor or yttrium-rich sputtering targets in an Ar:O{sub 2} or Ar:O{sub 2}:N{sub 2}O sputtering gas mixture. It was found that the use of yttrium-rich targets and N{sub 2}O in the sputtering gas is a reliable way to achieve smooth films without surface particles and with satisfactory superconducting properties, while the use of copper-poor targets and N{sub 2}O deteriorates those properties. Based on the previous results, YBCO/STO superlattices were grown using yttrium-rich YBCO targets and stoichiometric STO targets, respectively, in a Ar:O{sub 2}:N{sub 2}O sputtering gas mixture. The superlattices were found to have sharp interfaces and no indications of interface reactions were detected. 61 refs, 18 figs, 3 tabs

Out-of-substrate plane orientation control of thin YBa{sub 2}Cu{sub 3}O {sub x} films on NdGaO{sub 3} tilted-axes substrates

Energy Technology Data Exchange (ETDEWEB)

Mozhaev, Peter B. [Institute of Physics and Technology RAS, Moscow 117218 (Russian Federation) and Department of Physics, Technical University of Denmark, Lyngby, DK-2800 (Denmark)]. E-mail: pbmozh@nm.ru; Mozhaeva, Julia E. [Institute of Physics and Technology RAS, Moscow 117218 (Russian Federation); Department of Physics, Technical University of Denmark, Lyngby, DK-2800 (Denmark); Bdikin, Igor K. [Institute of Solid State Physics RAS, Chernogolovka, Moscow distr., 142432 (Russian Federation); CICECO, University of Aveiro, Aveiro 3810-193 (Portugal); Kotelyanskii, Iosif M. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation); Lusanov, Valery A. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation); Hansen, Jorn Bindslev [Department of Physics, Technical University of Denmark, Lyngby, DK-2800 (Denmark); Jacobsen, Claus S. [Department of Physics, Technical University of Denmark, Lyngby, DK-2800 (Denmark); Kholkin, Andrey L. [CICECO, University of Aveiro, Aveiro 3810-193 (Portugal)

2006-02-01

Epitaxial heterostructures YBa{sub 2}Cu{sub 3}O {sub x}(YBCO)/CeO{sub 2}/NdGaO{sub 3} were prepared on tilted-axes NdGaO{sub 3} substrates using laser ablation technique. Morphology, crystal structure and electrical properties of the obtained films were characterized. The seeding mechanisms are affected by the tilt angle, resulting in superior YBCO films on NdGaO{sub 3} substrates in an intermediate range of tilt angles of 6-14{sup o}. The introduction of CeO{sub 2} layer leads to change of the YBCO film orientation: at low deposition rate c-oriented films are formed, while at high deposition rates the film grows with c-axis tilted along the [1 1 0] NdGaO{sub 3} direction. Bi-epitaxial films and structures were prepared by removal of part of the CeO{sub 2} layer using ion-beam milling.

The ab-anisotropy of twinfree YBa2Cu3O7-delta above and below Tc

NARCIS (Netherlands)

Dam, B.; Rector, J.; Surdeanu, R.; Wijngaarden, R.J.; Koster, Gertjan; Peerdeman, F.; van Berkum, J.; de Groot, D.G.; Griessen, R.

1998-01-01

High quality twin-free c-axis oriented YBa2Cu3O7 films were grown by pulsed laser deposition on NdGaO3. We find resistive anisotropies between 1 < a/b < 1.6. The resistive anisotropy above Tc appears to be correlated to the anisotropy in the critical current below Tc. The normal state properties of

Depth profiling of transport properties of in-situ grown YBa_2Cu_3O_7-x films for coated conductor applications

Science.gov (United States)

Jo, William; Huh, J.-U.; Hammond, R. H.; Beasley, M. R.

2003-03-01

We report depth profiling of the local critical current density and resistivity of YBa_2Cu_3O_7-x (YBCO) films grown by in-situ electron beam evaporation. The method provides important information on the uniformity of the films, and therefore on the commonly observed property that the critical currents of coated conductor high temperature superconductor films do not scale linearly with thickness. Using a methodology of layer-by-layer etching, depth profiling of critical currents and resistivity of the films has been achieved. We use a Bromine methanol mixture to etch down YBCO films with an etch rate of 60 nm/min. At each step, we also observe surface morphology using high resolution scanning electron microscopy. In this talk, we report further study of the results found earlier that YBCO films deposited at high rates are composed of an upper layer of defected YBCO with a local Jc of 5 - 7 MA/cm^2 and a lower more perfect layer with no critical current capacity. The information derived may be useful in the characterization and optimization of superconducting thin films for electrical power and other applications.

Particulates reduction in laser-ablated YBa2Cu3O7-δ thin films by laser-induced plume heating

International Nuclear Information System (INIS)

Koren, G.; Baseman, R.J.; Gupta, A.; Lutwyche, M.I.; Laibowitz, R.B.

1990-01-01

Experimental demonstration of reduction in the number and size of particulates formed in the laser ablation deposition of YBa 2 Cu 3 O 7-δ thin films is obtained by the use of a second laser which further heats and fragments the blowoff material in the plume formed by the first laser. This results in a smoother film with higher critical current density as compared to that obtained without the second laser irradiation of the plume

Effect of cooling rate on the structure and properties of thick films of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Li, S.R.; Oleinikov, N.N.; Gas'kov, A.M.

1993-01-01

A problem associated with the production of quality films is chemical interaction of the HTSC material with the substrate. This leads to a considerable worsening or complete loss of the superconducting properties of a functional material. A second problem is selection of a substrate whose thermal expansion coefficient (TCE) is as close as possible to the TCE of the superconducting material. Omission of this condition leads to production of a HTSC material which is subject to perturbing mechanical stresses (compressive or tensile stress), and this is a potential cause of the reduction of the functional parameters of the material. The authors note that other substrate requirements should be considered only during production of thin films. Unfortunately, the production of quality thick films is apparently not worked out with resolution of the latter two problems. It is very important in production of HTSC materials to consider the rate of cooling at the moment of formation of the orthorhombic phase (in the following, the tetragonal-orthorhombic transition). Undesirable relaxation can be avoided if the cooling rate is lowered below some critical value. According to the computations, this problem is solved most successfully in HTSC materials of the composition YBa 2 Cu 3 O 7-x if their ceramic structure consists of crystallites whose size does not exceed 1-2 μm. The goal of this work is to elucidate the effect of the cooling rate of thick films of composition YBa 2 Cu 3 O 7-x in the temperature range corresponding to transition of the tetragonal to the orthorhombic phase on their structure and properties

The influence of growth temperature on the structural characteristics of YBa2Cu3O7-δ films: a Raman scattering study

International Nuclear Information System (INIS)

Belousov, M.V.; Davydov, V.Yu.; Sherman, A.B.

1993-01-01

Orientation of YBa 2 Cu 3 O 7-δ films at the surface and at the film-(100) MgO substrate interface for various growth temperatures T s have been studied using Raman scattering. On the film-substrate interface the films were c-oriented for T s >670 degrees C and a-oriented for lower growth temperatures. Films grown at T s approximately=670 degrees C to a thickness >0.2 mu m contained a transition from the c- to the a-orientation near the surface. A possible mechanism for the influence of growth temperature on the YBa 2 Cu 3 O 7-δ film orientation is discussed. (author)

The growth and characterisation of YBa2Cu3O7-δ superconducting thin films

International Nuclear Information System (INIS)

McCurry, M.P.

1999-02-01

The normal state properties of YBa 2 Cu 3 O 7-δ (YBCO) are not completely understood. It is known that the oxygen doping play a large part in determining these properties. The optical conductivity of a series of c-axis YBCO thin films was investigated in this thesis. The films were grown on (100) MgO substrates using a pulsed laser deposition (PLD) system and characterised using X-ray diffraction, atomic force microscopy and resistance-temperature measurements. The optimum parameters for c-axis YBCO thin film growth were determined by systematically varying the main deposition parameters. The best quality films had a transition temperature T c ∼ 88K, with a transition width ∼ 1-2K. Critical current densities of J c ∼ 10 7 Acm -2 were obtained. Substrate and target morphology affected the quality of the films. a-axis YBCO films were grown using a PrBa 2 Cu 3 O 7 (PBCO) film as a template for growth. The choice of target and substrate were again important, with a smooth substrate essential for the multi-layering. T c ∼ 83K and J c ∼ 10 6 Acm -2 were the best values obtained. These values compare with data published on the 'best' YBCO films deposited by PLD. A series of c-axis films was controllably under-doped using an ex-situ annealing process. The as-grown films were assumed to be optimally doped with δ ∼ 0.05. Doping levels in the 'metallic' region, 0.05 -2 mbar. Another tetragonal film was obtained by cooling it after deposition in a nitrogen atmosphere. Neither had a superconducting transition; the c-axes of both films were elongated. The films could be successfully re-doped with oxygen, with a subsequent return to optimal values of T c and c-axis lattice parameter. The dielectric function of optimally doped and under-doped c-axis YBCO films was determined using the attenuated total reflection (ATR) technique. This data was obtained at a fixed frequency of 2984 cm -1 , (0.366eV), at temperatures ranging from 300K to 80K. The data was analysed in

Thin film YBa{sub 2}Cu{sub 3}O{sub 7} junctions with La{sub 2/3}Ca{sub 1/3}MnO{sub 3} barrier

Energy Technology Data Exchange (ETDEWEB)

Hepting, Matthias; Stoehr, Andreas; Werner, Robert; Kleiner, Reinhold; Koelle, Dieter [Physikalisches Institut - Experimentalphysik II and Center for Collective Quantum Phenomena in LISAplus, Universitaet Tuebingen, Auf der Morgenstelle 14, 72076 Tuebingen (Germany)

2012-07-01

We report on the fabrication and electric transport properties of thin film YBa{sub 2}Cu{sub 3}O{sub 7} (YBCO) junctions with La{sub 2/3}Ca{sub 1/3}MnO{sub 3} (LCMO) barrier. Heteroepitaxial YBCO/LCMO/YBCO multilayers were grown in-situ by pulsed laser deposition and subsequently patterned by photolithography and Ar ion milling to form rectangular junctions with typical area 5 {mu}m x 30 {mu}m. A self-alignment process was used for electrical contact via an Au wiring layer to the upper YBCO electrode, similarly as described. Samples were characterized at temperature T=4.2 K either in magnetically shielded environment or in in-plane magnetic fields B up to the Tesla range. We present and discuss current-voltage-characteristics and measurements of critical current vs B.

Bi-epitaxial YBa2Cu3Ox Thin Films on Tilted-axes NdGaO3 Substrates with CeO2 Seeding Layer

International Nuclear Information System (INIS)

Mozhaev, P B; Mozhaeva, J E; Jacobsen, C S; Hansen, J Bindslev; Bdikin, I K; Luzanov, V A; Kotelyanskii, I M; Zybtsev, S G

2006-01-01

Bi-epitaxial YBa 2 Cu 3 O x (YBCO) thin films with out-of-plane tilt angle in the range 18 - 27 0 were manufactured using pulsed laser deposition on NdGaO 3 tilted-axes substrates with CeO 2 seeding layers. The YBCO thin film orientation over the seeding layer depended on deposition conditions. Removal of the seeding layer from part of the substrate surface by ionbeam etching resulted in formation of a bi-epitaxial thin film with different c-axis orientation of two parts of the film. The bi-epitaxial film orientation and structure were studied using X-ray diffraction techniques, and surface morphology was observed with atomic force microscope (AFM). Photolithography and ion-beam etching techniques were used for patterning bi-epitaxial thin films. Electrical characterization of the obtained structures was performed

Raman measurements of epitaxial YBa2Cu3O7-δ films

International Nuclear Information System (INIS)

Burns, G.; Dacol, F.H.; Gield, C.A.; Gupta, A.; Holtzberg, F.; Koren, G.; Laibowitz, R.; McGuire, T.R.; Segmuller, A.P.; Worthington, T.K.

1990-01-01

The authors report Raman measurements on good (high J c ) epitaxial YBa 2 Cu 3 O -δ (Y123) films (δ ∼ 0). The results are compared to those from oriented Y123 single crystals. The comparisons are made for superconducting δ ∼ 0 and semiconducting δ ∼ 1 materials

Enhancement of critical current density of YBa2Cu3O7-δ thin films by nanoscale CeO2 pretreatment of substrate surfaces

International Nuclear Information System (INIS)

Cui, X.M.; Liu, G.Q.; Wang, J.; Huang, Z.C.; Zhao, Y.T.; Tao, B.W.; Li, Y.R.

2007-01-01

YBa 2 Cu 3 O 7-δ (YBCO) films were prepared on single-crystal SrTiO 3 substrates with metal-organic deposition using trifluoroacetates (TFA-MOD). Positive results have been acquired in controlled study to investigate the effects of substrate surface modification on the growth-induced flux-pinning nanostructures in YBCO films. Nanoscale CeO 2 particles were applied to single-crystal SrTiO 3 substrate surfaces using pulsed laser deposition before YBCO precursors coating. Superconducting properties of the YBCO films grown on the controlled CeO 2 -modified substrates have shown substantial improvement in the critical current densities (J c ) at 77 K over those grown on untreated substrates in almost all the field (78% increment at 1 T, 77 K). We think the reason is that the CeO 2 nanoparticles act as pinning centers

Epitaxial growth of YBa2Cu307−δ films on SrTiO3 (100) by direct solution precursor deposition

International Nuclear Information System (INIS)

Bustamante, A; Garcia, Jorge; Osorio, Ana M; Valladares, Luis De Los Santos; Barnes, C H W; González, J C; Azuma, Y; Majima, Y; Aguiar, J Albino

2014-01-01

We study the optimal temperature to obtain YBa 2 Cu 3 O 7-δ epitaxial films grown onto SrTiO 3 substrates by direct solution deposition. The samples received heat treatment at 820, 840 and 860 °C, then characterized by XRD, observing the (00l) profiles; and magnetic susceptibility measurements. The T C-onset for all the samples was 90 K. In addition, the current – voltage (I-V) measurements shows typical tunneling signals corresponding to normal metal-superconducting junctions indicating the films are promising for potential electrical applications.

Annihilation of positrons with localized electrons in oxides and YBa2Cu3O7-x ceramics

International Nuclear Information System (INIS)

Nishchenko, M.M.; Likhtorovich, S.P.

1997-01-01

The angular correlation of annihilation photons (ACAP) has been studied in CuO, Cu 2 O,BaO,Y 2 O 3 and YBa 2 Cu 3 O 7-x oxides. Localization radius of the electron wave function is found to be about 0,8 A. It is also shown that with the more localization of the electron its probability of annihilation with positrons is less

Studies of metallic species incorporation during growth of SrBi2Ta2O9 films on YBa2Cu3O7-x substrates using mass spectroscopy of recoiled ions

International Nuclear Information System (INIS)

Dhote, A. M.

1999-01-01

The incorporation of metallic species (Bi, Sr and Ta) during the growth of layered perovskite SrBi 2 Ta 2 O 9 (SBT) on a-axis oriented YBa 2 Cu 3 O 7-x (YBCO) conducting oxide substrates has been investigated using in situ low energy mass spectroscopy of recoiled ions (MSRI). This technique is capable of providing monolayer-specific surface information relevant to the growth of single and multi-component thin films and layered heterostructures. The data show a temperature dependence of metallic species incorporation during co-deposition of Sr, Bi and Ta on YBCO surfaces. At high temperatures (400 400 C. SBT films grown at temperatures ≤ 400 C and annealed in oxygen or air at 800 C exhibit a polycrystalline structure with partial a-axis orientation

Crystal growth of YBa2Cu3O(7-x) and reaction of gold crucible with Ba-Cu-rich flux

Science.gov (United States)

Tao, Y. K.; Chen, H. C.; Martini, L.; Bechtold, J.; Huang, Z. J.; Hor, P. H.

1991-01-01

YBa2Cu3O(7-x) crystals are grown in a gold crucible by a self-flux method. The flux moves along the gold surface due to surface wetting and leaves Y123 crystals behind. The obtained crystals are clean and have a size up to two millimeters and a Tc is greater than 90 K. In an effort to recycle the used crucibles, it is found that the used gold is contaminated by copper. A CuO thin film is easily formed on the surface of the crucible that is made of the used gold. This film provides good surface wetting and a buffer layer, which reduces the reaction between gold and the Y-Ba-Cu-oxide melt.

Fabrication of nanometer flat areas onto YBa2Cu3O7-x thin film surfaces by scanning tunneling microscope

International Nuclear Information System (INIS)

Virtanen, J.A.; Suketu, P.; Huth, G.C.; Cho, Z.H.

1991-01-01

A scanning tunneling microscope was used to mechanically ''mill'' nanometer flat areas of up to 1600 μm 2 on high temperature superconducting (HTS) films of YBa 2 Cu 3 O 7-x which were originally formed by laser ablation. Flatness to a standard deviation of 2 nm in height was found to be characteristic of milled areas. It was subsequently possible to mill trenches and ditches onto these flat areas. Scanning tunneling measurements of the exposed layered structure of the milled HTS surface are also reported. Surface modifications are also possible by the application of voltage pulse to the tunneling tip. The combination of electrical pulses and milling offer a possibility of mixed electromechanical patterning of the film

Geometric and compositional factors on critical current density in YBa2Cu3O7‑δ films containing nanorods

Science.gov (United States)

Horide, Tomoya; Nagao, Sho; Izutsu, Ryosuke; Ishimaru, Manabu; Kita, Ryusuke; Matsumoto, Kaname

2018-06-01

Critical current density (J c) was investigated in YBa2Cu3O7‑δ films containing nanorods prepared with various nanorod materials, with variation of nanorod content, substrate temperature, and oxidization condition. Three types of compositional situation were realized: films containing strain induced oxygen vacancies; fully oxidized films containing cation compositional deviation; and oxygen deficient films. Normalized J c‑B behavior was determined via the matching field, which is a geometric factor, regardless of the compositional details. A J c‑critical temperature (T c) relation depending on distribution and fraction of compositional deviation (cation compositional deviation and strain induced oxygen vacancies) was found: the J c values decreased with decreasing T c due to the effect of T c on nanorod pinning strength in the fully oxidized films; J c decreased with decreasing oxygen pressure in the film cooling process after film deposition in spite of T c remaining almost the same, due to reduction of the effective area for current flow in the oxygen deficient films. Thus, a J c landscape based on geometric and compositional factors was obtained. The study highlights the importance of the J c‑T c analysis in the understanding of J c in YBa2Cu3O7‑δ films containing nanorods.

Microstructure and transport current characterization of YBa2Cu3O7-x thick films prepared by modified solid-liquid melt growth and powder melt process routes

International Nuclear Information System (INIS)

Langhorn, J.; McGinn, P.J.

1999-01-01

From the characterization of superconducting YBa 2 Cu 3 O 7-x (YBCO) thick films processed by melt texturing on yttria-stabilized zirconia substrates from YBCO precursors it is clear that the properties are highly dependent on the precursor powder. Increased YBCO grain sizes have been induced in thick films processed from by modified solid-liquid melt growth (SLMG) and powder melt (PMP) processes with respect to those processed from pre-reacted YBCO materials. The SLMG and PMP routes utilize precursors consisting of BaCuO 2 -CuO flux material mixed with Y 2 O 3 and Y 2 BaCuO 5 respectively. Cross-sectional analysis of films textured by these routes shows a decreased Y 2 BaCuO 5 size and an increased homogeneity within the matrix with respect to films processed from YBCO powder. Such microstructural improvements lead to an improvement of both the flux pinning and current-carrying characteristics of the processed YBCO films. (author)

Stoichiometry and superconductive properties of YBaCuO films deposited by spray pyrolysis

International Nuclear Information System (INIS)

Conde-Gallardo, A.; Falcony, C.; Ortiz, A.

1994-01-01

The dependence of the stoichiometry and the superconducting characteristics of YBaCuO films deposited by spray pyrolysis on the spraying solution composition and the deposition conditions is reported. It has been found that a proper optimization of the starting materials concentration in the spraying solution results in superconducting films with zero resistance temperature of 91 K and a transition to superconducting state within a 3 K range. X-ray diffraction and resistance vs temperature measurements have been used to monitor the crystal composition and the conductive characteristics of the films as a function of the spraying solution composition and the deposition parameters

Structure/Property Relationships for Sol-gel Derived YBa2Cu3O7-d and SrTiO3 Films

Science.gov (United States)

Dawley, Jeff; Clem, Paul; Siegal, Michael; Overmyer, Don

2001-03-01

Solution deposition of c-axis oriented YBa2Cu3O7-d (YBCO) films on buffered RABiT substrates is a potential method for rapid, low cost production of superconducting tapes for power transmission and other applications. For this work, 100-250 nm thick YBCO and SrTiO3 (STO) films have been prepared by spin-coating and dip-coating sol-gel solutions onto LaAlO3 (100) and RABiT Ni (200) substrates. Biaxially textured STO coatings have been deposited on LaAlO3 and RABiT Ni by using a "templating" technique and controlling growth temperature and pO2. YBCO films grown on STO coated LaAlO3 possess comparable superconducting properties to YBCO films grown directly on LaAlO3 ( 1 MA/cm2 at 77K), indicating that a high quality STO layer does not degrade the crystalline quality of the YBCO. The effects of processing parameters on the STO buffer layer and novel processing techniques for decreasing the processing time and simplifying the integration of sol-gel YBCO with Ni substrates will be discussed. Sandia is a multiprogram laboratory operated by Sandia Corp., a Lockheed Martin Company, for the US Dept. Of Energy under contract DE-AC04-94A185000.

Morphology, structure, and electrical properties of YBa{sub 2}Cu{sub 3}O{sub x} thin films on tilted NdGaO{sub 3} substrates, deposited by DC-sputtering

Energy Technology Data Exchange (ETDEWEB)

Mozhaev, Peter B. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation)]. E-mail: pbmozh@nm.ru; Kotelyanskii, Iosif M. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation); Luzanov, Valery A. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation); Mozhaeva, Julia E. [Institute of Radio Engineering and Electronics RAS, Moscow 125009 (Russian Federation); Donchev, Todor [Institute of Electronics BAS, Sofia (Bulgaria); Mateev, Emil [Institute of Electronics BAS, Sofia (Bulgaria); Nurgaliev, Timur [Institute of Electronics BAS, Sofia (Bulgaria); Bdikin, Igor K. [Institute of Solid State Physics RAS, Chernogolovka, Moscow 142432 (Russian Federation); Department of Ceramic and Glass Engineering, CICECO, University of Aveiro, Aveiro 3810-193 (Portugal); Narymbetov, Bakhyt Zh. [Complex Institute of Natural Sciences UzAS, Nukus (Uzbekistan)

2005-02-15

Thin YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) films were deposited using DC-sputtering technique on NdGaO{sub 3} substrates, tilted from (1 1 0) orientation by 0-26 deg . The structure and surface quality of the substrates were carefully characterized to obtain reliable results of thin films deposition. Structural, morphological and electrical properties of the YBCO thin films show three different ranges of inclination angle: vicinal, intermediate and high. In the vicinal range the properties of the film are generally the same as of the standard films deposited on (1 1 0) NdGaO{sub 3} substrate. An increase of the inclination angle to the intermediate range results in a significant improvement of morphology and structural quality of the film. Best electrical parameters are measured for the films of the intermediate range also. Probable reason for such behavior is simultaneous and regular seeding of the film in the joints of facets on the substrate surface. Further increase of inclination angle leads to step bunching and oxygen out-diffusion, destroying both structural and electrical perfection of the tilted-axes YBCO film.

Growth of Highly Epitaxial YBa2Cu3O7-δ Films from a Simple Propionate-Based Solution

DEFF Research Database (Denmark)

Yue, Zhao; Torres, Pol; Tang, Xiao

2015-01-01

Intensive investigations have been conducted to develop epitaxial oxide thin films with superior electromagnetic performance by low-cost chemical solution deposition routes. In this paper, a novel propionate-based precursor solution without involving any other additive was proposed and employed...... to grow superconducting YBa2Cu3O7-δ (YBCO) films on LaAlO3 (LAO) single crystals. The precursor solutions are stable with a long shelf life of up to several months. Since the primary compositions are propionates after evaporating the solvent, the toxic reagents and evolved gases during solution synthesis...... and heat treatment can be eliminated completely. In this process, rapid pyrolysis and high conversation rate can also be achieved during growth of YBCO films in comparison with the conventional trifluoroacetate metal organic deposition routes. Remarkably, a 210 nm YBCO film exhibits high superconducting...

High J{sub c} YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} Films via Rapid, Low pO{sub 2} Pyrolysis

Energy Technology Data Exchange (ETDEWEB)

DAWLEY,JEFFREY T.; CLEM,PAUL G.; SIEGAL,MICHAEL P.; OVERMYER,DONALD L.

2000-09-21

In this investigation, YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} (YBCO) films were fabricated via a metal acetate, trifluoroacetic acid based sol-gel route, and spin-coat deposited on (100) LaAlO{sub 3} with a focus on maximizing J{sub c}, while minimizing processing time. We demonstrate that the use of a low pO{sub 2} atmosphere during the pyrolysis stage can lead to at least a tetiold reduction in pyrolysis time, compared to a 1 atm. O{sub 2} ambient. High-quality YBCO films on LaAlO{sub 3}, with J{sub c} values up to 3 MA/cm{sup 2} at 77 K, can be routinely crystallized from these rapidly pyrolyzed films.

Improved flux-pinning properties of REBa{sub 2}Cu{sub 3}O{sub 7-z} films by low-level Co doping

Energy Technology Data Exchange (ETDEWEB)

Wang, Wentao; Pu, Minghua; Wang, Weiwei; Lei, Ming [Key Laboratory of Magnetic Levitation and Maglev Trains, Ministry of Education of China, Superconductivity R and D Centre (SRDC), Southwest Jiaotong University, Erhuanlu Beiyiduan 111, 610031 Chengdu (China); Cheng, Cuihua [Superconductivity Research Group, School of Materials Science and Engineering, University of New South Wales, 2052 NSW, Sydney (Australia); Zhao, Yong [Key Laboratory of Magnetic Levitation and Maglev Trains, Ministry of Education of China, Superconductivity R and D Centre (SRDC), Southwest Jiaotong University, Erhuanlu Beiyiduan 111, 610031 Chengdu (China); Superconductivity Research Group, School of Materials Science and Engineering, University of New South Wales, 2052 NSW, Sydney (Australia)

2011-09-15

Biaxially textured REBa{sub 2}Cu{sub 3-x}Co{sub x}O{sub 7-z} (RE = Gd,Y) films were prepared on (00l) LaAlO{sub 3} substrate using self-developed fluorine-free chemical solution deposition (CSD) approach. The in-field J{sub c} values are significantly improved for REBa{sub 2}Cu{sub 3-x}Co{sub x}O{sub 7-z} films through low-level Co doping. Co-doped GdBa{sub 2}Cu{sub 3}O{sub 7-z} film shows the highest J{sub c} values at higher temperatures and fields, whereas the J{sub c} values of Co-doped YBa{sub 2}Cu{sub 3}O{sub 7-z} film surpass that of other films at lower temperatures and fields. In addition, the volume pinning force densities of films with Co doping have been distinctly enhanced in the applied fields, indicating improved flux-pinning properties. The possible reasons are discussed in detail. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Preparation of YBa2Cu3O7 films by low pressure MOCVD using liquid solution sources

International Nuclear Information System (INIS)

Weiss, F.; Froehlich, K.; Haase, R.; Labeau, M.; Selbmann, D.; Senateur, J.P.; Thomas, O.

1993-01-01

A hybrid low pressure MOCVD process is described for reproducible preparation of superconducting thin films of YBa 2 Cu 3 O 7 . The process uses a single solution source of Y, Ba, and Cu β-diketonates dissolved in suitable organic solvents. This liquid precursor is atomized using an ultrasonic aerosol generator and transported as small droplets (∼1μm) into a CVD reactor where solvent and precursor are first evaporated before deposition takes place at low pressure on heated substrates in a cold wall geometry. This process allows, with stable evaporation rates for all three precursors, to grow in-situ superconducting films with constant composition from film to film. Thin and thick films with high critical temperatures and critical currents have been obtained (Tc>80K, Jc>10 4 A/cm 2 at 77K in self field) which are highly c-axis oriented. Experimental details of this new process are described and the effects of different process parameters are studied in order to improve the quality of the deposited layers. (orig.)

Strategic Research on Performance Optimization of YBa2Cu3O7 Coated Conductors

International Nuclear Information System (INIS)

Aytug, Tolga; Christen, David K.; Kim, Kyunghoon; Lupini, Andrew R.; Paranthaman, Mariappan Parans; Polat, Ozgur; Thompson, James R.; Xiong, X.; Selvamanickam, V.; Meyer, Harry M. III; Qiu, Xiaofeng

2008-01-01

Practical applications of second generation (2G) high temperature superconductor (HTS) wires require high critical current density, Jc, at high temperatures and magnetic fields. It has been well established that Jc can be increased via nanostructural engineering of artificial pinning centers within the HTS matrix. In the present work, composite LaMnO3:MgO (LMO:MgO) cap buffer layers with varying MgO contents 5 vol% up to 75 vol% have been grown on homo-epi MgO/IBAD(MgO) substrates to enhance the performance of YBa2Cu3O7-x (YBCO) films. Results showed formation of phase separated MgO nanocolumns within the LMO matrix. The impact of these nanocolumns on the superconducting properties of YBCO films deposited on the nanostructured layer was investigated by electrical transport measurements. Such YBCO films showed better in-field performance compared to that of YBCO films on standard LMO cap films. In particular, measurements of the field-angle dependence revealed c-axis correlated pinning for YBCO films on these composite cap layers. The present results demonstrate a practical approach to obtain high performance superconducting wires.

Josephson edge junctions on YBa2Cu3O7 thin films prepared with Br-ethanol etching

International Nuclear Information System (INIS)

Faley, M.I.; Poppe, U.; Daehne, U.; Goncharov, Yu.G.; Klein, N.; Urban, K.; Soltner, H.

1993-01-01

To produce damage-free edges is one of the main problems in the preparation of the Josephson edge-type junctions and interconnects in multilayer structures including high temperature superconductors. The commonly used ion beam etching has the disadvantages of the risk of contamination by redeposited material and structural damage to the surface of the edge. Vasquez et al and Gurvitch et al introduced a nonaqueous Br-ethanol etching for the preparation of clean surfaces of YBa 2 Cu 3 O 7 single crystals and thin films. We have developed a procedure of deep-UV-photolithography combined with nonaqueous Br-ethanol etching for the preparation of the Josephson edge-type junctions. Here we present the improvement of this method and report further results on the study of the electron transport properties of Josephson junctions with the edges of YBa 2 Cu 3 O 7 thin films produced by this technique. (orig.)

Mechanical properties of partially meltable superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/

International Nuclear Information System (INIS)

Selvamanickam, V.; Salama, K.

1988-01-01

Partial melting has been suggested as a method for the processing of the high temperatures superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ to improve the current carrying capacity in this material. The authors have investigated the possibility of using this method for the improvement of bulk mechanical properties in addition to those related to superconductivity. Four parameters, namely, oxygen annealing temperature, melting temperature, melting time and cooling rate are identified and studied. Each parameter is varied individually and its effects on microstructure and mechanical and superconducting properties are examined. The results indicate that the properties of superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ can be improved significantly using the proper melting temperature, melting time, cooling rate and oxygen annealing temperature

Fabrication and characterization of Ba sub x Sr sub 1 sub - sub x TiO sub 3 /YBa sub 2 Cu sub 3 O sub x /SrTiO sub 3 structure

CERN Document Server

Choi, J; Park, S Y; Lee Jae Sik; No, K; Sung, T H; Park, Y

2002-01-01

Ba sub x Sr sub 1 sub - sub x TiO sub 3 (BST)/YBa sub 2 Cu sub 3 O sub x (YBCO)/SrTiO sub 3 (STO) structures were deposited, and the microstructure, orientation and electrical characteristics were investigated. (00l) oriented YBCO thin films were deposited on STO substrates using pulsed laser deposition, and (h00) oriented BST thin films were deposited on YBCO/STO substrates using electron cyclotron resonance (ECR) plasma assisted metal organic chemical vapor deposition (MOCVD). A new phase was formed at the interface between YBCO and BST films and was speculated to be (Ba sub x Y sub 1 sub - sub x)(Ti sub y Y sub 1 sub - sub y)O sub 3. Ba-rich BST films showed a higher dielectric loss than Sr-rich BST films did, which indicates that Sr-rich BST films are more suited for application to microwave devices. The dielectric loss of the films was reduced as temperature decreased, which may be due to the conductivity change of YBCO film and the formation of a conduction path rather than a dielectric property change ...

Momentum Dependence of Charge Excitations in YBa2Cu3O7-δ and Nd2-xCexCuO4

Science.gov (United States)

Ishii, Kenji

2006-03-01

Resonant inelastic x-ray scattering (RIXS) studies at Cu K-edge on high-Tc superconducting cuprates, YBa2Cu3O7-δ and Nd2-xCexCuO4 are presented. The superconductivity occurs in the vicinity of the Mott insulating state and it is important to clarify the nature of the Mott gap and its doping dependence. Because RIXS has an advantage that we can measure charge excitation in a wide energy-momentum space, it gives a unique opportunity to study the electronic structure of materials. We apply this technique to high-Tc superconducting cuprates. In particular the electronic structure of strongly correlated metals is in the focus of our RIXS study. The experiments were performed at BL11XU of SPring-8, Japan, where a specially designed spectrometer for inelastic x-ray scattering is installed. In optimally doped YBa2Cu3O7-δ, anisotropic spectra are observed in the ab plane of a twin-free crystal. The Mott gap excitation from the one-dimensional CuO chain is enhanced at 2 eV near the zone boundary of the chain direction, while the excitation from the CuO2 plane is broad at 1.5-4 eV and almost independent of momentum. Theoretical calculation based on the one-dimensional and two-dimensional Hubbard model reproduces the observed features in the RIXS spectra when smaller values of the on-site Coulomb energy of the chain than that of the plane are assumed. This means that the charge transfer gap of the chain is smaller than that of the plane. On the other hand, both interband excitation across the Mott gap and intraband excitation in the upper Hubbard band are observed in the electron-doped Nd2-xCexCuO4. The intensity of the interband excitation is concentrated at ˜ 2 eV near the zone boundary while a dispersion relation with a momentum-dependent width emerges in the intraband excitation. The author would like to acknowledge to his collaborators, K. Tsutsui, Y. Endoh, T. Tohyama, K. Kuzushita, T. Inami, K. Ohwada, M. Hoesch, M. Tsubota, Y. Murakami, J. Mizuki, S. Maekawa, T

High T/sub c/ screen-printed YBa2Cu3O/sub 7-//sub x/ films: Effect of the substrate material

International Nuclear Information System (INIS)

Bansal, N.P.; Simons, R.N.; Farrell, D.E.

1988-01-01

Thick films of YBa 2 Cu 3 O/sub 7-//sub x/ have been deposited on highly polished alumina, magnesia spinel, nickel aluminum titanate (Ni-Al-Ti), and barium tetratitanate (Ba-Ti) substrates by the screen printing technique. They were baked at 1000 0 C for 15 min, oxygen annealed at a lower temperature, and characterized by electrical resistivity measurements, x-ray diffraction, and optical and scanning electron microscopy. Properties of the films were found to be highly sensitive to the choice of the substrate material. The film on Ba-Ti turned green after firing, due to a reaction with the substrate and were insulating. A film on Ni-Al-Ti had a T/sub c/ (onset) ∼95 K and lost 90% of its resistance by ∼75 K. However, even at 4 K it was not fully superconducting, possibly due to a reaction between the film and the substrate and interdiffusion of the reaction products. The film on alumina had T/sub c/ (onset) ∼96 K, T/sub c/ (zero) ∼66 K, and ΔT/sub c/ (10--90%) ∼10 K. Our best film was obtained on spinel and had T/sub c/ (onset) ∼94 K, zero resistance at 81 K, and a transition width (10--90%) of ∼7 K

ab-Plane Anisotropy of Transport Properties in Unidirectionally Twinned YBa2Cu3O7-δ Films

International Nuclear Information System (INIS)

Villard, C.; Chateignier, D.; Thrane, B.; Koren, G.; Cohen, D.; Polturak, E.

1996-01-01

A unidirectionally twinned, c oriented YBa 2 Cu 3 O 7-δ film was prepared on a (001) NdGaO 3 substrate. In the normal state between 100 and 300K, the unidirectional twin plane lattice induces a strong anisotropy of ρ ab , leading to a temperature independent ratio of 6 between the resisitivities across and along the twin boundaries. At 77K, the self-field critical current parallel to twin planes is 1.2x10 6 A/cm 2 , a value which is 25 times higher than along the perpendicular direction. This shows that, at this temperature, twin boundaries control the critical current values in YBCO films by either channeling or pinning effects. copyright 1996 The American Physical Society

Laser writing and rewriting on YBa2Cu3O7 films

International Nuclear Information System (INIS)

Shen, Y.Q.; Freltoft, T.; Vase, P.

1991-01-01

High-resolution patterning (4 μm) has been achieved on epitaxial thin films of the high-temperature superconductor YBa 2 Cu 3 O 7-δ using laser writing. A focused laser beam is applied to write semiconducting patterns on superconducting films in a vacuum or in a nitrogen atmosphere. The semiconducting patterns are shown to be formed by a reduction of the oxygen content due to local heating caused by the laser beam. The process does not cause any structural damage and does not change the surface morphology. When reapplying the same laser beam and rewriting the film in an oxygen atmosphere, it is possible to restore the superconductive properties. The application of this method for production of superconducting microelectronic circuits is discussed

Morphology, structure, and electrical properties of YBa2Cu3Ox thin films on tilted NdGaO3 substrates, deposited by DC-sputtering

International Nuclear Information System (INIS)

Mozhaev, Peter B.; Kotelyanskii, Iosif M.; Luzanov, Valery A.; Mozhaeva, Julia E.; Donchev, Todor; Mateev, Emil; Nurgaliev, Timur; Bdikin, Igor K.; Narymbetov, Bakhyt Zh.

2005-01-01

Thin YBa 2 Cu 3 O x (YBCO) films were deposited using DC-sputtering technique on NdGaO 3 substrates, tilted from (1 1 0) orientation by 0-26 deg . The structure and surface quality of the substrates were carefully characterized to obtain reliable results of thin films deposition. Structural, morphological and electrical properties of the YBCO thin films show three different ranges of inclination angle: vicinal, intermediate and high. In the vicinal range the properties of the film are generally the same as of the standard films deposited on (1 1 0) NdGaO 3 substrate. An increase of the inclination angle to the intermediate range results in a significant improvement of morphology and structural quality of the film. Best electrical parameters are measured for the films of the intermediate range also. Probable reason for such behavior is simultaneous and regular seeding of the film in the joints of facets on the substrate surface. Further increase of inclination angle leads to step bunching and oxygen out-diffusion, destroying both structural and electrical perfection of the tilted-axes YBCO film

Femtosecond optical detection of quasiparticle dynamics in high- T sub c YBa sub 2 Cu sub 3 O sub 7 minus. delta. superconducting thin films

Energy Technology Data Exchange (ETDEWEB)

Han, S.G.; Vardeny, Z.V.; Wong, K.S.; Symko, O.G. (Department of Physics, University of Utah, Salt Lake City, UT (USA)); Koren, G. (Department of Physics, Technion, 32000 Haifa (Israel))

1990-11-19

Femtosecond dynamics of photogenerated quasiparticles in YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} superconducting thin films shows, at {ital T}{le}{ital T}{sub {ital c}}, two main electronic processes: (i) quasiparticle avalanche production during hot-carrier thermalization, which takes about 300 fsec; (ii) recombination of quasiparticles to form Cooper pairs, which is completed within 5 psec. In contrastr, nonsuperconducting epitaxial films such as PrBa{sub 2}Cu{sub 2}O{sub 7} and YBa{sub 2}Cu{sub 3}O{sub 6} show regular picosecond electronic response.

Raman scattering studies on superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/, semiconducting YBa/sub 2/Cu/sub 3/O/sub 6+x/, and possible impurity phases

International Nuclear Information System (INIS)

Mascarenhas, A.; Katayama-Yoshida, H.; Geller, S.; Pankove, J.I.; Deb, S.K.

1988-01-01

A Raman spectroscopic investigation of specimens of superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ and semiconducting YBa/sub 2/Cu/sub 3/O/sub 6+x/ indicates that in the range 100 to 700 cm/sup -1/, the characteristic lines of the superconductor at 13 K, are at 150, 338, 441, 507, 590, and 644 cm/sup -1/. Comparison of the Raman spectra of the superconductor and the semiconductor indicates a mode stiffening of the pair at 338 and 441 cm/sup -1/, but a mode softening of the pair at 507 and 590 cm/sup -1/. A factor group analysis leads to a tentative assignment of the Raman and infrared allowed modes. At temperatures 12K ≤ T ≤ 180K the Raman spectra of the superconductor indicate that the phonon mode at 338 cm/sup -1/ has an anomaloys temperature dependence below the superconducting critical temperature (T/sub c/)

Formation of nanoparticles and defects in YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} prepared by the metal organic deposition process

Energy Technology Data Exchange (ETDEWEB)

Goswami, R. [Naval Research Laboratory, Washington, DC 20375 (United States); SAIC, Washington, DC 20003 (United States)], E-mail: goswami@anvil.nrl.navy.mil; Holtz, R.L. [Naval Research Laboratory, Washington, DC 20375 (United States); Rupich, M.W. [American Superconductors Inc., Westborough, MA 01581 (United States); Spanos, G. [Naval Research Laboratory, Washington, DC 20375 (United States)

2007-11-15

Nanoparticles and defects have been investigated using transmission electron microscopy in fully reacted YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO), prepared by the metal-organic deposition (MOD) process. Two types of particles, Y{sub 2}O{sub 3} and CuY{sub 2}O{sub 5}, ranging from 10 to 100 nm, have been observed in the YBCO matrix. The YBCO contains a large number of planar defects and a considerable number of (1 1 0) rotational twins. Details of the nanoparticles and defects in the MOD-processed YBCO films are presented in this paper.

Junction structures based on the high-Tc superconductor YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Gijs, M.A.M.

1993-01-01

An overview is given of the investigations of the Josephson effect in junction structures based on the high-T c superconductor YBa 2 Cu 3 O 7-δ , which were carried out at the Philips Research Laboratories in Eindhoven in the 1988-1990 period. The reported results are presented in their international scientific context, without attempting a complete review of the subject. However, the various junction types studied give a good idea of the scientific pursuits of high-T c junction researchers in this period. The following junctions are considered: in the category of 'weak link'-type junctions we have investigated YBa 2 Cu 3 O 7-δ -Ag-Nb point contact junctions, YBa 2 Cu 3 O 7-δ Dayem bridges and YBa 2 Cu 3 O 7-δ -Ag(-Al)-Pb proximity junctions. In these structures we combine a high-T c with a low-T c superconductor. We also fabricated planar 'all high-T c ' YBa 2 Cu 3 O 7-δ -Ag-YBa 2 Cu 3 O 7-δ junctions using a submicron structuring process. Next we have made tunnel junctions to study density of states effects of the high-T c superconductor : YBa 2 Cu 3 O 7-δ -Pb junctions using the degraded YBa 2 Cu 3 O 7-δ -Pb interface as a tunnel barrier, and YBa 2 Cu 3 O 7-δ -Ag-Al/Al 2 O 3 /Pb tunnel junctions based on the superconducting proximity effect. Our junction structures are electrically characterized and mostly studied in microwave and magnetic fields. Results are compared with current theoretical models. (orig.)

High resolution electron microscopy and electron diffraction of YBa2Cu3O(7-x)

International Nuclear Information System (INIS)

Krakow, W.; Shaw, T.M.

1988-01-01

Experimental high resolution electron micrographs and computer simulation experiments have been used to evaluate the visibility of the atomic constituents of YBa 2 Cu 3 O(7-x). In practice, the detection of oxygen has not been possible in contradiction to that predicted by modelling of perfect crystalline material. Preliminary computer experiments of the electron diffraction patterns when oxygen vacancies are introduced on the Cu-O sheets separating Ba layers show the diffuse streaks characteristic of short range ordering. 7 references

Current transport and electronic states in a,b-axis-oriented YBa2Cu3O7/PrBa2Cu3O7/YBa2Cu3O7 sandwich-type junctions

International Nuclear Information System (INIS)

Yoshida, J.; Nagano, T.; Hashimoto, T.

1996-01-01

Precise measurement of the temperature and voltage dependence of junction conductance has been carried out for a,b-axis-oriented YBa 2 Cu 3 O 7 /PrBa 2 Cu 3 O 7 /YBa 2 Cu 3 O 7 sandwich-type junctions to investigate the possible origin of Josephson coupling in these junctions. Regardless of the presence or absence of the Josephson effect, most of the junctions exhibited a dip in conductance around zero voltage in their dI/dV profiles at low temperatures. This dI/dV anomaly was attributed to the existence of a minimum in the density of states due to electron-electron interaction in disordered metals in the vicinity of a tunneling barrier within the junctions. The complex temperature dependence of junction conductance was reproduced well by a theoretical model in which both tunneling conduction paths and variable range hopping paths were assumed to exist within the PrBa 2 Cu 3 O 7 barrier layer. No definite evidence of current transport through a small number of localized levels or a metallic conduction path in PrBa 2 Cu 3 O 7 has been confirmed, even for junctions with a 20-nm-thick barrier layer. copyright 1996 The American Physical Society

LaNiO3 buffer layers for high critical current density YBa2Cu3O7-δ and Tl2Ba2CaCu2O8-δ films

International Nuclear Information System (INIS)

Carlson, C.M.; Parilla, P.A.; Siegal, M.P.; Ginley, D.S.; Wang, Y.; Blaugher, R.D.; Price, J.C.; Overmyer, D.L.; Venturini, E.L.

1999-01-01

We demonstrate high critical current density superconducting films of YBa 2 Cu 3 O 7-δ (YBCO) and Tl 2 Ba 2 CaCu 2 O 8-δ (Tl-2212) using LaNiO 3 (LNO) buffer layers. YBCO films grown on an LNO buffer layer have only a slightly lower J c (5 K, H=0) than films grown directly on a bare LaAlO 3 substrate. YBCO films grown on LNO buffer layers exhibit minor microstructural disorder and enhanced flux pinning. LNO-buffered Tl-2212 samples show large reductions in J c at all temperatures and fields compared to those grown on bare LaAlO 3 , correlating to both a-axis grain and nonsuperconducting phase formation. LNO could be a promising buffer layer for both YBCO and Tl-based superconducting films in coated conductor applications. copyright 1999 American Institute of Physics

LaNiO3 Buffer Layers for High Critical Current Density YBa2Cu3O7δ and Tl2Ba2CaCu2O8δ Films

International Nuclear Information System (INIS)

Carlson, C.M.; Parilla, P.A.; Siegal, M.P.; Ginley, D.S.; Wang, Y.-T.; Blaugher, R.D.; Price, J.C.; Overmyer, D.L.; Venturini, E.L.

1999-01-01

We demonstrate high critical current density superconducting films of YBa 2 Cu 3 O 7-δ (YBCO) and Tl 2 Ba 2 CaCu 2 O 8-δ (Tl-2212) using LaNiO 3 (LNO) buffer layers. YBCO films grown on an LNO buffer layer have only a slightly lower J c (5K, H=0) than films grown directly on a bare LaAlO 3 substrate. It is noteworthy that YBCO films grown on LNO buffer layers exhibit minor microstructural disorder and enhanced flux pinning. LNO-buffered Tl-2212 samples show large reductions in J c at all temperatures and fields compared to those grown on bare LaAlO 3 , correlating to both a-axis grain and nonsuperconducting phase formation. With additional optimization, LNO could be a promising buffer layer for both YBCO and Tl-based superconducting films, perhaps ideally suited for coated conductor applications

Flux pinning enhancements in YBa2Cu3O7-8 superconductors through phase separated, self-assembled LaMnO3-MgO nanocomposite films.

Energy Technology Data Exchange (ETDEWEB)

Polat, Ozgur [ORNL; Aytug, Tolga [ORNL; Paranthaman, Mariappan Parans [ORNL; Leonard, Keith J [ORNL; Pennycook, Stephen J [ORNL; Kim, Kyunghoon [ORNL; Cook, Sylvester W [ORNL; Thompson, James R [ORNL; Christen, David K [ORNL; Goyal, Amit [ORNL; Selvamanickam, V. [SuperPower Incorporated, Schenectady, New York; Lupini, Andrew R [ORNL; Meyer, Hendrik [ORNL; Qiu, Xiaofeng [ORNL; Xiong, X. [SuperPower Incorporated, Schenectady, New York

2011-01-01

Technological applications of high temperature superconductors (HTS) require high critical current density, Jc, under operation at high magnetic field strengths. This requires effective flux pinning by introducing artificial defects through creative processing. In this work, we generated correlated disorder for strong vortex pinning in the YBa2Cu3O7- (YBCO) films by replacing the standard LaMnO3 (LMO) cap buffer layers in ion beam assisted deposited MgO templates with LMO:MgO composite films. Such films revealed formation of two phase-separated, but at the same time vertically aligned, self-assembled composite nanostructures that extend throughout the entire thickness of the film. Measurements of magnetic-field orientation-dependent Jc of YBCO coatings deposited on these nanostructured cap layers showed correlated c-axis pinning and improved in-field Jc performance compared to those of YBCO films deposited on standard LMO buffers. The present results demonstrate feasibility of novel and potentially practical approaches in the pursuit of more efficient, economical, and high performance superconducting devices.

Growth and properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/YBa{sub 2}Cu{sub 3}O{sub 7−δ}/La{sub 0.7}Sr{sub 0.3}MnO{sub 3} epitaxial trilayer films

Energy Technology Data Exchange (ETDEWEB)

Sharma, Minaxi, E-mail: meenanith@gmail.com; Kumar, Arvind; Sharma, K. K. [Department of Physics, National Institute of Technology, Hamirpur -177005 (India); Kumar, Ravi [Centre for Materials Science and Engineering, National Institute of Technology, Hamirpur -177005 (India); Beant College of Engineering and Technology, Gurdaspur Punjab-143521 (India); Choudhary, R. J. [UGC-DAE-Consortium for Scientific Research, Khandwa Road, Indore-452001 (India)

2015-08-28

We report the growth and properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/YBa{sub 2}Cu{sub 3}O{sub 7−δ}/La{sub 0.7}Sr{sub 0.3}MnO{sub 3} LSMO/YBCO/LSMO epitaxial trilayer films, fabricated on SrTiO{sub 3} substrate using pulsed laser deposition technique. From x-ray diffraction and high resolution x-ray diffraction measurements, it is confirmed that the grown trilayered films are single phase and epitaxial in nature. Magneto-transport and magnetic properties are found to be dependent on the thickness of YBCO spacer layer. We infer that for fixed thickness of top and bottom LSMO layers, superconductivity is completely suppressed. At 100 K, the hysteresis loops reveal the ferromagnetic signature of trilayered film. At room temperature, we obtain a butterfly type scenario, signifies the co-existence of ferromagnetic and antiferromagnetic interaction. In addition, at room temperature, the YBCO spacer layer allowing the top and bottom LSMO layers to interact antiferromagnetically.

Preparation and properties of Y{sub 1-x}Ho{sub x}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} thin films by TFA-MOD method

Energy Technology Data Exchange (ETDEWEB)

Jian Hongbin [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China); Li Qi; Shi Dongqi [Institute for Superconducting and Electronic Materials, University of Wollongong, Wollongong 2522 (Australia); Zhang Li [Department of Mathematic and Physics, Anhui University of Architecture, Hefei 230022 (China); Yang Zhaorong [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China); Dou Shixue [Institute for Superconducting and Electronic Materials, University of Wollongong, Wollongong 2522 (Australia); Zhu Xuebin, E-mail: xbzhu@issp.ac.cn [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China); Sun Yuping [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2011-12-15

Y{sub 1-x}Ho{sub x}BCO thin films were prepared by TFA-MOD. The best performances were obtained for the Y{sub 0.6}Ho{sub 0.4}BCO thin film. The pinning mechanism was {delta}l-type for all derived thin films. Y{sub 1-x}Ho{sub x}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) thin films were prepared on LaAlO{sub 3} (0 0 1) substrates by trifluoroacetate metal organic deposition (TFA-MOD) without change of the processing parameters. The highest J{sub c} was attributed to the sample of Y{sub 0.6}Ho{sub 0.4}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} thin film, whose critical current density is about 1.6 times as compared to that of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} thin film at 77 K and self field. The flux pinning type was not varied with Ho substitution and can be attributed to {delta}l pinning model, which is attributed to the close ionic radius between the Y{sup 3+} and Ho{sup 3+} ions. The improvement of J{sub c} by Ho substitution without change of the processing parameters will provide an effective route to enhance the J{sub c} of YBCO-based thin films using TFA-MOD method.

Oxygen desorption from YBa2Cu3O(7-x) and Bi2CaSr2Cu2O(8 + delta) superconductors

Science.gov (United States)

Mesarwi, A.; Levenson, L. L.; Ignatiev, A.

1991-01-01

Oxygen desorption experiments from YBa2Cu3O(7-x) (YBCO) and Bi2CaSr2Cu2O(8 + delta) (BSCCO) superconductors were carried out using a quadrupole mass spectrometer for monitoring the desorbing species and X-ray photoemission spectroscopy for surface characterization. Molecular oxygen was found to desorb from both superconductors following photoirradiation with ultraviolet/optical radiation and subsequent heating at over 150 C. Both YBCO and BSCCO were found to have similar oxygen desorption rates and similar activation energies. The desorption data as well as the X-ray photoemission data indicate that the oxygen desorption is not intrinsic to the superconductors but rather due to molecular oxygen entrapped in the material.

Análisis de la textura fuera-del-plano en capas superconductoras de YBa2Cu3O7-X

OpenAIRE

Sanchez, H.; Bustamante, A.; Osorio, A.; De los Santos, L.; González, J.C.; Barnes, C.H.W.

2015-01-01

En el presente trabajo estudiamos la textura de capas superconductoras de YBa2Cu3O7-da través de la difracción de rayos-X. Las capas fueron crecidas sobre el sustrato monocristalino SrTiO3 (100) mediante la deposición de solución química. Posteriormente se sometió la muestra a tratamientos térmicos en una atmósfera oxidante. Una caracterización mediante difracción de rayos-X revela la presencia de reflexiones (00l) para la fase de YBa2Cu3O7-d con una fracción de granos superconductores orient...

Barium contributions to the valence electronic structure of YBa2Cu3O7-δ, PrBa2Cu3O7-δ, and other barium-containing compounds

International Nuclear Information System (INIS)

Mueller, D.R.; Wallace, J.S.; Jia, J.J.; O'Brien, W.L.; Dong, Q.; Callcott, T.A.; Miyano, K.E.; Ederer, D.L.

1995-01-01

Monochromatic photon beams were used to excite barium N IV,V soft x-ray emission spectra from YBa 2 Cu 3 O 7-δ , PrBa 2 Cu 3 O 7-δ , BaF 2 , and BaTiO 3 . Near threshold excitation was used to demonstrate that small contributions to the barium N V and N IV emission spectra in the energy region above the 5p→4d core-core transitions do not arise as satellite emission from transitions in multiply excited atoms but rather occur as a result of transitions from the valence states. The emission spectrum of YBa 2 Cu 3 O 7-δ and PrBa 2 Cu 3 O 7-δ reveals a contribution to the electronic density of states at the barium site in the region near the Fermi level. The YBa 2 Cu 3 O 7-δ compound is a superconductor and PrBa 2 Cu 3 O 7-δ is an insulator. It has been proposed that the difference between them is due to mixing of praseodymium and barium among the sites occupied by yttrium and barium, with an accompanying change in electronic structure. However, our measurements indicate that the barium partial density of states for the two compounds are essentially identical

High Ic, YBa2Cu3O7-x films grown at very high rates by liquid assisted growth incorporating lightly Au-doped SrTiO3 buffers

International Nuclear Information System (INIS)

Kursumovic, A; Durrell, J H; Harrington, S; Wimbush, S; MacManus-Driscoll, J L; Maiorov, B; Zhou, H; Stan, L; Holesinger, T G; Wang, H

2009-01-01

YBa 2 Cu 3 O 7-x (YBCO) thick films were grown by hybrid liquid phase epitaxy (HLPE) on (001) SrTiO 3 (STO) substrates. In the presence of a 100 nm thick, 5 mol% Au-doped STO buffer, self-field critical current densities, J c sf , at 77 K of ∼2.4 MA cm -2 and critical currents, I c sf , up to 700 A (cm-width) -1 were achieved. The J c value is virtually independent of thickness and the growth rates are very high (∼1 μm min -1 ). From transmission electron microscopy (TEM), Y 2 O 3 nanocloud extended defects (∼100 nm in size) were identified as the pinning defects in the films. Enhanced random pinning was induced by the presence of Au in the buffer.

Interaction of RBa sub 2 Cu sub 3 O sub x (R = Y or Nd) coatings with alumina and zirconia substrates. [YBaCuO; NdBaCuO

Energy Technology Data Exchange (ETDEWEB)

Moreau, C; Parent, L; Champagne, B; Dallaire, S [National Research Council of Canada, Industrial Materials Research Inst., Boucherville, PQ (Canada)

1989-12-10

As-deposited YBa{sub 2}Cu{sub 3}O{sub x} coatings by plasma spraying are not superconducting because of their inadequate crystalline structure and low oxygen content. A post-deposition heat treatment in oxygen is required to restore the appropriate superconducting YBa{sub 2}Cu{sub 3}O{sub x} structure. During heat treatment, deterimental reactions between coatings and substrates may occur and lead to the degradation or destruction of the coating superconducting properties. In the present paper, interactions of RBa{sub 2}Cu{sub 3}O{sub x} (R = Y, Nd) coatings with alumina and zirconia substrates are examined. The modifications of the coating electrical properties and microstructure are studied using X-ray diffraction, energy dispersive X-ray analysis and resistivity measurements. Coating degradation is shown to occur by diffusion of the barium atoms out of the coating leading to the formation of Y{sub 2}BaCuO{sub 5} and CuO in yttrium-based coatings, and to the formation of nonstoichiometric Nd{sub 1+y}Ba{sub 2-y}Cu{sub 3}O{sub x} and CuO in neodymium-based coatings. The coating degradation is more important on alumina substrates that on zirconia substrates for both yttrium- and neodymium-based coatings. (orig.).

LaNiO(3) Buffer Layers for High Critical Current Density YBa(2)Cu(3)O(7-delta) and Tl(2)Ba(2)CaCu(2)O(8-delta) Films

Energy Technology Data Exchange (ETDEWEB)