WorldWideScience

Sample records for dental composite resin

  1. Nanomechanical properties of dental resin-composites.

    Science.gov (United States)

    El-Safty, S; Akhtar, R; Silikas, N; Watts, D C

    2012-12-01

    To determine by nanoindentation the hardness and elastic modulus of resin-composites, including a series with systematically varied filler loading, plus other representative materials that fall into the categories of flowable, bulk-fill and conventional nano-hybrid types. Ten dental resin-composites: three flowable, three bulk-fill and four conventional were investigated using nanoindentation. Disc specimens (15mm×2mm) were prepared from each material using a metallic mold. Specimens were irradiated in the mold at top and bottom surfaces in multiple overlapping points (40s each) with light curing unit at 650mW/cm(2). Specimens were then mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. After grinding and polishing, specimens were stored in distilled water at 37°C for 7 days. Specimens were investigated using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius). Each specimen was loaded at one loading rate and three different unloading rates (at room temperature) with thirty indentations, per unloading rate. The maximum load applied by the nanoindenter to examine the specimens was 10mN. Dependent on the type of the resin-composite material, the mean values ranged from 0.73GPa to 1.60GPa for nanohardness and from 14.44GPa to 24.07GPa for elastic modulus. There was a significant positive non-linear correlation between elastic modulus and nanohardness (r(2)=0.88). Nonlinear regression revealed a significant positive correlation (r(2)=0.62) between elastic moduli and filler loading and a non-significant correlation (r(2)=0.50) between nanohardness and filler loading of the studied materials. Varying the unloading rates showed no consistent effect on the elastic modulus and nanohardness of the studied materials. For a specific resin matrix, both elastic moduli and nanohardness correlated positively with filler loading. For the resin-composites investigated, the group-average elastic

  2. Abrasive wear and surface roughness of contemporary dental composite resin.

    Science.gov (United States)

    Han, Jian-min; Zhang, Hongyu; Choe, Hyo-Sun; Lin, Hong; Zheng, Gang; Hong, Guang

    2014-01-01

    The purpose of this study was to evaluate the abrasive wear and surface roughness of 20 currently available commercial dental composite resins, including nanofilled, supra-nanofilled, nanohybrid and microhybrid composite resins. The volume loss, maximum vertical loss, surface roughness (R(a)) and surface morphology [Scanning electron microscopy (SEM)] were determined after wear. The inorganic filler content was determined by thermogravimetric analysis. The result showed that the volume loss and vertical loss varied among the materials. The coefficients of determination (R(2)) of wear volume loss and filler content (wt%) was 0.283. SEM micrographs revealed nanofilled composites displayed a relatively uniform wear surfaces with nanoclusters protrusion, while the performance of nanohybrid composites varied. The abrasive wear resistance of contemporary dental composite resins is material-dependent and cannot be deduced from its category, filler loading and composite matrix; The abrasive wear resistance of some flowable composites is comparable to the universal/posterior composite resins.

  3. Metameric effect between dental porcelain and porcelain repairing resin composite.

    Science.gov (United States)

    Kim, Sung-Hee; Lee, Yong-Keun; Lim, Bum-Soon; Rhee, Sang-Hoon; Yang, Hyeong-Cheol

    2007-03-01

    The objectives were to evaluate the metameric color and hue angle (degrees) changes between dental porcelain and porcelain repairing resin composites. Color of three shades (A2, A3, A3.5) of one brand of dental porcelain and three original shades (A2, A3, A3.5) and three combinations (A2-A3, A3-3.5, A2-A3.5) of three brands of porcelain repairing resin composites (ABT, FSP, TCR) were measured relative to the three standard illuminants (D65, A and F2). Specimen was 2mm in thickness, and 1mm of each shade was layered to make combined shades. Color differences (DeltaEab*) between each shade of dental porcelain and repairing resin composites relative to the three illuminants were calculated, and the ratios of color difference (modified metamerism index) by the change of illuminant were calculated. The ratios of hue angle changes were also compared. Differences in modified metamerism index and the ratio of hue angle changes were influenced by the porcelain shade, brand of resin composites and shade of resin composites. In all three brands of resin composites, A3.5 shade showed the smallest values in modified metamerism index regardless of the shade of porcelain. The average ratio of hue angle changes between each porcelain shade and all the shades of each resin composites showed similar trend when illuminant was changed from D65 to F2. Metameric effect between dental porcelain and repairing resin composites varied depending on the shade of porcelain, brand of resin composite and the illuminant. Therefore, shade matching between porcelain and repairing resin composite should be performed carefully. This study confirmed that shades should be matched under the light corresponding to that of use.

  4. Resin-composite blocks for dental CAD/CAM applications.

    Science.gov (United States)

    Ruse, N D; Sadoun, M J

    2014-12-01

    Advances in digital impression technology and manufacturing processes have led to a dramatic paradigm shift in dentistry and to the widespread use of computer-aided design/computer-aided manufacturing (CAD/CAM) in the fabrication of indirect dental restorations. Research and development in materials suitable for CAD/CAM applications are currently the most active field in dental materials. Two classes of materials are used in the production of CAD/CAM restorations: glass-ceramics/ceramics and resin composites. While glass-ceramics/ceramics have overall superior mechanical and esthetic properties, resin-composite materials may offer significant advantages related to their machinability and intra-oral reparability. This review summarizes recent developments in resin-composite materials for CAD/CAM applications, focusing on both commercial and experimental materials. © International & American Associations for Dental Research.

  5. Degradation, Fatigue, and Failure of Resin Dental Composite Materials

    Energy Technology Data Exchange (ETDEWEB)

    Drummond, J.L. (UIC)

    2008-11-03

    The intent of this article is to review the numerous factors that affect the mechanical properties of particle- or fiber-filler-containing indirect dental resin composite materials. The focus will be on the effects of degradation due to aging in different media, mainly water and water and ethanol, cyclic loading, and mixed-mode loading on flexure strength and fracture toughness. Several selected papers will be examined in detail with respect to mixed and cyclic loading, and 3D tomography with multi-axial compression specimens. The main cause of failure, for most dental resin composites, is the breakdown of the resin matrix and/or the interface between the filler and the resin matrix. In clinical studies, it appears that failure in the first 5 years is a restoration issue (technique or material selection); after that time period, failure most often results from secondary decay.

  6. Dental repair material: a resin-modified glass-ionomer bioactive ionic resin-based composite.

    Science.gov (United States)

    Croll, Theodore P; Berg, Joel H; Donly, Kevin J

    2015-01-01

    This report documents treatment and repair of three carious teeth that were restored with a new dental repair material that features the characteristics of both resin-modified glass-ionomer restorative cement (RMGI) and resin-based composite (RBC). The restorative products presented are reported by the manufacturer to be the first bioactive dental materials with an ionic resin matrix, a shock-absorbing resin component, and bioactive fillers that mimic the physical and chemical properties of natural teeth. The restorative material and base/liner, which feature three hardening mechanisms, could prove to be a notable advancement in the adhesive dentistry restorative materials continuum.

  7. Degradation of dental resin composites during intra-oral wear

    NARCIS (Netherlands)

    Yulianto, Heribertus Dedy Kusuma

    2017-01-01

    Dental resin composites have become an integral part of modern dentistry and used worldwide to restore missing tooth structures, to modify tooth color and anatomical contour, and to enhance aesthetics and function. The dentist should be aware that, the aggressive complexity of the oral environment

  8. High elastic modulus nanopowder reinforced resin composites for dental applications

    Science.gov (United States)

    Wang, Yijun

    2007-12-01

    Dental restorations account for more than $3 billion dollars a year on the market. Among them, all-ceramic dental crowns draw more and more attention and their popularity has risen because of their superior aesthetics and biocompatibility. However, their relatively high failure rate and labor-intensive fabrication procedure still limit their application. In this thesis, a new family of high elastic modulus nanopowder reinforced resin composites and their mechanical properties are studied. Materials with higher elastic modulus, such as alumina and diamond, are used to replace the routine filler material, silica, in dental resin composites to achieve the desired properties. This class of composites is developed to serve (1) as a high stiffness support to all-ceramic crowns and (2) as a means of joining independently fabricated crown core and veneer layers. Most of the work focuses on nano-sized Al2O3 (average particle size 47 nm) reinforcement in a polymeric matrix with 50:50 Bisphenol A glycidyl methacrylate (Bis-GMA): triethylene glycol dimethacrylate (TEGDMA) monomers. Surfactants, silanizing agents and primers are examined to obtain higher filler levels and enhance the bonding between filler and matrix. Silane agents work best. The elastic modulus of a 57.5 vol% alumina/resin composite is 31.5 GPa compared to current commercial resin composites with elastic modulus alumina, diamond/resin composites are studied. An elastic modulus of about 45 GPa is obtained for a 57 vol% diamond/resin composite. Our results indicate that with a generally monodispersed nano-sized high modulus filler, relatively high elastic modulus resin-based composite cements are possible. Time-dependent behavior of our resin composites is also investigated. This is valuable for understanding the behavior of our material and possible fatigue testing in the future. Our results indicate that with effective coupling agents and higher filler loading, viscous flow can be greatly decreased due to the

  9. Early failure of Class II resin composite versus Class II amalgam restorations placed by dental students.

    Science.gov (United States)

    Overton, J D; Sullivan, Diane J

    2012-03-01

    Using the information from remake request slips in a dental school's predoctoral clinic, we examined the short-term survival of Class II resin composite restorations versus Class II dental amalgam restorations. In the student clinic, resin composite is used in approximately 58 percent of Class II restorations placed, and dental amalgam is used in the remaining 42 percent. In the period examined, Class II resin composite restorations were ten times more likely to be replaced at no cost to the patient than Class II dental amalgam restorations. A total of eighty-four resin composite restorations and six amalgam restorations were replaced due to an identified failure.

  10. Elution of monomer from different bulk fill dental composite resins.

    Science.gov (United States)

    Cebe, Mehmet Ata; Cebe, Fatma; Cengiz, Mehmet Fatih; Cetin, Ali Rıza; Arpag, Osman Fatih; Ozturk, Bora

    2015-07-01

    The purpose of this study was to evaluate the elution of Bis-GMA, TEGDMA, HEMA, and Bis-EMA monomers from six bulk fill composite resins over four different time periods, using HPLC. Six different composite resin materials were used in the present study: Tetric Evo Ceram Bulk Fill (Ivoclar Vivadent, Amherst, NY), X-tra Fill (VOCO, Cuxhaven, Germany), Sonic Fill (Kerr, Orange, CA, USA), Filtek Bulk Fill (3M ESPE Dental Product, St. Paul, MN), SDR (Dentsply, Konstanz, Germany), EQUIA (GC America INC, Alsip, IL). The samples (4mm thickness, 5mm diameter) were prepared and polymerized for 20s with a light emitted diode unit. After fabrication, each sample was immediately immersed in 75wt% ethanol/water solution used as extraction fluid and stored in the amber colored bottles at room temperature. Ethanol/water samples were taken (0.5mL) at predefined time intervals:10m (T1), 1h (T2), 24h (T3) and 30 days (T4). These samples were analyzed by HPLC. The obtained data were analyzed with one-way ANOVA and Tukey HSD at significance level of pcomposites (pcomposite resins in all time periods and the amount of eluted monomers was increased with time. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  11. Hygroscopic expansion kinetics of dental resin-composites.

    Science.gov (United States)

    Alrahlah, A; Silikas, N; Watts, D C

    2014-02-01

    To evaluate the extent and rate of hygroscopic expansion of resin composites at 37°C. Eight resin composites were examined: 1 micro-hybrid (Bright Light(®)), 5 nano-hybrids (Experimental Vertise™; Nanoceram-Bright(®); Tetric EvoCeram(®); Grandio(®) SO; Ceram X™ duo) and 2 flowables (X-tra base; Venus(®) Diamond Flow). Five disks (15 mm×2 mm) of each material were prepared. The mean change in specimen diameter was recorded by a custom-built non-contact laser micrometer. Specimens were initially measured dry and then at fixed time intervals, over 150 days, after storage in distilled water at 37±1°C. Data were re-expressed in volumetric terms and analysed by repeated measures ANOVA, one-way ANOVA and Tukey's post hoc test (α=0.05). The volumetric hygroscopic expansion ranged from 0.58 to 2.26 and can be considered in three bands. First, Experimental Vertise had the highest expansion (pGrandio So, Nanoceram-Bright and X-tra base, with no significant difference between them. For the size (2mm thickness) and shape of specimen measured, equilibrium was attained in all cases by 60 days. Within this set of resin-composites the equilibrium expansion varied by almost 400% of the lowest material. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  12. Longevity of posterior resin composite restorations in permanent teeth in Public Dental Health Service

    DEFF Research Database (Denmark)

    Pallesen, Ulla; van Dijken, Jan W V; Halken, Jette

    2013-01-01

    To investigate in a prospective follow up the longevity of posterior resin composites (RC) placed in permanent teeth of children and adolescents attending Public Dental Health Service.......To investigate in a prospective follow up the longevity of posterior resin composites (RC) placed in permanent teeth of children and adolescents attending Public Dental Health Service....

  13. Five-year clinical performance of posterior resin composite restorations placed by dental students.

    NARCIS (Netherlands)

    Opdam, N.J.M.; Loomans, B.A.C.; Roeters, F.J.M.; Bronkhorst, E.M.

    2004-01-01

    OBJECTIVES: To investigate the survival over a five-year period of posterior resin composite restorations placed by students. METHODS: Class I and II resin composite restorations placed by second-fourth year dental students were evaluated. Patients attended the dental school every 6 months for a

  14. Relationship between Color and Translucency of Multishaded Dental Composite Resins

    Directory of Open Access Journals (Sweden)

    Homan Naeimi Akbar

    2012-01-01

    Full Text Available The aim of the present study was to compare the translucency of different shades of two highly aesthetic multilayered restorative composite resins. In total nine shades from Esthet.X and ten shades from Filtek Supreme composite resins were chosen. Discs of each shade were prepared (N=3 and light-cured. Total and diffuse transmittance values for each sample were measured. Statistical analysis showed that the opaque dentine shades of both composites were the least translucent and the enamel shades had the highest translucency. There was a significant decrease in translucency from A2 to C2 of regular body shades and also from A4 to C4 of opaque dentine shades of Esthet.X composite resin. Grey enamel shade had a significantly higher diffuse translucency compared to clear and yellow enamel shades. There was a significant decrease in translucency from A2B to D2B and also in diffuse translucency from A4D to C6D shades of Filtek Supreme composite resin. It can be concluded that the color of the composite resins tested in this study had a significant effect on their translucency. Information on the translucency of different shades of composite resins can be very useful for the clinicians in achieving optimal esthetic restorative outcome.

  15. Interface structure and strength in model dental resin composites

    DEFF Research Database (Denmark)

    Nielsen, Mette Skovgaard

    Most composites for dental restoration are based on a methacrylate polymer matrix and a ceramic filler, often silanized silica or silicate glasses. A problem with these composites is the polymerization shrinkage, which causes the filling to loosen from the tooth under formation of a crack....... This will facilitate discoloration by colorants from e.g. coffee and red wine entering the crack, or even worse lead to secondary caries and infection of dental pulp due to bacteria. The aim of this study was to develop a low shrinkage dental composite based on an expandable metastable zirconia filler A metastable...... the polymer shrinkage and reduces the overall shrinkage of the composite. In this thesis the zirconia filler is characterized and tested for the potential as a filler for use in dental composites. The zirconia powder is composed of highly agglomerated particles of nanosized crystals. The average particle size...

  16. Effect of resin chemistry on depth of cure and cytotoxicity of dental resin composites

    Energy Technology Data Exchange (ETDEWEB)

    Susila Anand, V. [Rehabilitation Bioengineering Group, Department of Engineering Design, Indian Institute of Technology Madras, Chennai 600036 (India); Department of Conservative Dentistry and Endodontics, Saveetha Dental College, Saveetha University, Chennai 600077 (India); Balasubramanian, Venkatesh, E-mail: chanakya@iitm.ac.in [Rehabilitation Bioengineering Group, Department of Engineering Design, Indian Institute of Technology Madras, Chennai 600036 (India)

    2014-02-15

    Highlights: • Dental composites have differences in polymerization within 2 mm thickness. • Degree of conversion alone may not affect the biocompatibility of composite. • Unreacted double bonds in dental composites may influence biocompatibility. • Magnitude of double bonds depends on the polymerization and chemical composition. • These influence biocompatibility especially if they possess lipophylic properties. -- Abstract: New dental composite restorative materials are being introduced aiming to overcome the disadvantages of contemporary materials. Hence there is a need to analyze the critical properties of these composites to aid in clinical application. This study aims to comparatively analyze the degree of conversion (DC), residual reactivity (DBC/reactivity) and cytotoxicity of 2 composites based on different resin chemistry. Ceram X and Filtek P90 were used in the study to prepare disc shaped samples of 2 mm thickness and 4 mm diameter. The samples for cytotoxicity were cured for 40 s and those of Fourier Transform Infra-red Spectroscopy (FTIR) (DBC/reactivity and DC) for 5 s, 10 s, 20 s and 40 s, at an average intensity of 800 mW/cm{sup 2} with Quartz–Tungsten–Halogen (QTH) light. DC was calculated in 60–100 μm thick and 6 mm diameter samples. Double bonds concentration/reactivity was measured in approximately 80 μm thick sections prepared from the 2 mm thick discs using a hard tissue microtome. The cell viability was scored by Trypan blue exclusion staining technique at 24 h and 48 h. Both composites showed a progressive increase in double bonds/reactivity as the distance from curing probe increased which was inversely proportional to the curing time. The DC of Filtek P90 was 20% and 96% and that of Ceram X 33% and 50% at 5 s and 40 s, respectively. Ceram X showed statistically significantly higher cell viability score at both 24 h and 48 h than Filtek P90. The results were statistically analyzed using non-parametric Kruskal

  17. Effect of resin chemistry on depth of cure and cytotoxicity of dental resin composites

    International Nuclear Information System (INIS)

    Susila Anand, V.; Balasubramanian, Venkatesh

    2014-01-01

    Highlights: • Dental composites have differences in polymerization within 2 mm thickness. • Degree of conversion alone may not affect the biocompatibility of composite. • Unreacted double bonds in dental composites may influence biocompatibility. • Magnitude of double bonds depends on the polymerization and chemical composition. • These influence biocompatibility especially if they possess lipophylic properties. -- Abstract: New dental composite restorative materials are being introduced aiming to overcome the disadvantages of contemporary materials. Hence there is a need to analyze the critical properties of these composites to aid in clinical application. This study aims to comparatively analyze the degree of conversion (DC), residual reactivity (DBC/reactivity) and cytotoxicity of 2 composites based on different resin chemistry. Ceram X and Filtek P90 were used in the study to prepare disc shaped samples of 2 mm thickness and 4 mm diameter. The samples for cytotoxicity were cured for 40 s and those of Fourier Transform Infra-red Spectroscopy (FTIR) (DBC/reactivity and DC) for 5 s, 10 s, 20 s and 40 s, at an average intensity of 800 mW/cm 2 with Quartz–Tungsten–Halogen (QTH) light. DC was calculated in 60–100 μm thick and 6 mm diameter samples. Double bonds concentration/reactivity was measured in approximately 80 μm thick sections prepared from the 2 mm thick discs using a hard tissue microtome. The cell viability was scored by Trypan blue exclusion staining technique at 24 h and 48 h. Both composites showed a progressive increase in double bonds/reactivity as the distance from curing probe increased which was inversely proportional to the curing time. The DC of Filtek P90 was 20% and 96% and that of Ceram X 33% and 50% at 5 s and 40 s, respectively. Ceram X showed statistically significantly higher cell viability score at both 24 h and 48 h than Filtek P90. The results were statistically analyzed using non-parametric Kruskal–Wallis, Mann

  18. Dental composite resins: measuring the polymerization shrinkage using optical fiber Bragg grating sensors

    Science.gov (United States)

    Ottevaere, H.; Tabak, M.; Chah, K.; Mégret, P.; Thienpont, H.

    2012-04-01

    Polymerization shrinkage of dental composite materials is recognized as one of the main reasons for the development of marginal leakage between a tooth and filling material. As an alternative to conventional measurement methods, we propose optical fiber Bragg grating (FBG) based sensors to perform real-time strain and shrinkage measurements during the curing process of dental resin cements. We introduce a fully automated set-up to measure the Bragg wavelength shift of the FBG strain sensors and to accurately monitor the linear strain and shrinkage of dental resins during curing. Three different dental resin materials were studied in this work: matrix-filled BisGMA-based resins, glass ionomers and organic modified ceramics.

  19. BACTERIAL ADHESION TO DENTAL AMALGAM AND 3 RESIN COMPOSITES

    NARCIS (Netherlands)

    SULJAK, JP; REID, G; WOOD, SM; MCCONNELL, RJ; VANDERMEI, HC; BUSSCHER, HJ

    Objectives: The ability of three oral bacteria to adhere to hydrophobic amalgam (water contact angle 60 degrees) and hydrophobic resin composites (Prisma-AP.H 56 degrees, Herculite XRV 82 degrees and Z100 89 degrees) was compared using an in vitro assay. Methods and results: Following preincubation

  20. Mechanical properties of dental resin/composite containing urchin-like hydroxyapatite.

    Science.gov (United States)

    Liu, Fengwei; Sun, Bin; Jiang, Xiaoze; Aldeyab, Sultan S; Zhang, Qinghong; Zhu, Meifang

    2014-12-01

    To investigate the reinforcing effect of urchin-like hydroxyapatite (UHA) in bisphenol A glycidyl methacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) dental resin (without silica nanoparticles) and dental composites (with silica nanoparticles), and explore the effect of HA filler morphologies and loadings on the mechanical properties. UHA was synthesized by a facile method of microwave irradiation and studied by X-ray diffraction (XRD), scanning electron microscope (SEM), and thermogravimetric analysis (TGA). Mechanical properties of the dental resin composites containing silanized UHA were tested by a universal mechanical testing machine. Analysis of variance was used for the statistical analysis of the acquired data. The fracture morphologies of tested composites were observed by SEM. Composites with silanized irregular particulate hydroxyapatite (IPHA) and hydroxyapatite whisker (HW) were prepared for comparative studies. Impregnation of lower loadings (5 wt% and 10 wt%) of silanized UHA into dental resin (without silica nanoparticles) substantially improved the mechanical properties; higher UHA loadings (20 wt% and 30 wt%) of impregnation continuously improved the flexural modulus and microhardness, while the strength would no longer be increased. Compared with silanized IPHA and HW, silanized UHA consisting of rods extending radially from center were embedded into the matrix closely and well dispersed in the composite, increasing filler-matrix interfacial contact area and combination. At higher filler loadings, UHA interlaced together tightly without affecting the mobility of monomer inside, which might bear higher loads during fracture of the composite, leading to higher strengths than those of dental resins with IPHA and HW. Besides, impregnation of silanized UHA into dental composites (with silica nanoparticles) significantly improved the strength and modulus. UHA could serve as novel reinforcing HA filler to improve the mechanical properties

  1. Effect of in-office bleaching agents on physical properties of dental composite resins.

    Science.gov (United States)

    Mourouzis, Petros; Koulaouzidou, Elisabeth A; Helvatjoglu-Antoniades, Maria

    2013-04-01

    The physical properties of dental restorative materials have a crucial effect on the longevity of restorations and moreover on the esthetic demands of patients, but they may be compromised by bleaching treatments. The purpose of this study was to evaluate the effects of in-office bleaching agents on the physical properties of three composite resin restorative materials. The bleaching agents used were hydrogen peroxide and carbamide peroxide at high concentrations. Specimens of each material were prepared, cured, and polished. Measurements of color difference, microhardness, and surface roughness were recorded before and after bleaching and data were examined statistically by analysis of variance (ANOVA) and Tukey HSD post-hoc test at P composite resin altered after the bleaching procedure (P composite resins tested (P > .05). The silorane-based composite resin tested showed some color alteration after bleaching procedures. The bleaching procedure did not alter the microhardness and the surface roughness of all composite resins tested.

  2. Interpenetrating network ceramic-resin composite dental restorative materials.

    Science.gov (United States)

    Swain, M V; Coldea, A; Bilkhair, A; Guess, P C

    2016-01-01

    This paper investigates the structure and some properties of resin infiltrated ceramic network structure materials suitable for CAD/CAM dental restorative applications. Initially the basis of interpenetrating network materials is defined along with placing them into a materials science perspective. This involves identifying potential advantages of such structures beyond that of the individual materials or simple mixing of the components. Observations from a number of recently published papers on this class of materials are summarized. These include the strength, fracture toughness, hardness and damage tolerance, namely to pointed and blunt (spherical) indentation as well as to burr adjustment. In addition a summary of recent results of crowns subjected to simulated clinical conditions using a chewing simulator are presented. These results are rationalized on the basis of existing theoretical considerations. The currently available ceramic-resin IPN material for clinical application is softer, exhibits comparable strength and fracture toughness but with substantial R-curve behavior, has lower E modulus and is more damage tolerant than existing glass-ceramic materials. Chewing simulation observations with crowns of this material indicate that it appears to be more resistant to sliding/impact induced cracking although its overall contact induced breakage load is modest. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. Synthesis of wrinkled mesoporous silica and its reinforcing effect for dental resin composites.

    Science.gov (United States)

    Wang, Ruili; Habib, Eric; Zhu, X X

    2017-10-01

    The aim of this work is to explore the reinforcing effect of wrinkled mesoporous silica (WMS), which should allow micromechanical resin matrix/filler interlocking in dental resin composites, and to investigate the effect of silica morphology, loading, and compositions on their mechanical properties. WMS (average diameter of 496nm) was prepared through the self-assembly method and characterized by the use of the electron microscopy, dynamic light scattering, and the N 2 adsorption-desorption measurements. The mechanical properties of resin composites containing silanized WMS and nonporous smaller silica were evaluated with a universal mechanical testing machine. Field-emission scanning electron microscopy was used to study the fracture morphology of dental composites. Resin composites including silanized silica particles (average diameter of 507nm) served as the control group. Higher filler loading of silanized WMS substantially improved the mechanical properties of the neat resin matrix, over the composites loaded with regular silanized silica particles similar in size. The impregnation of smaller secondary silica particles with diameters of 90 and 190nm, denoted respectively as Si90 and Si190, increased the filler loading of the bimodal WMS filler (WMS-Si90 or WMS-Si190) to 60wt%, and the corresponding composites exhibited better mechanical properties than the control fillers made with regular silica particles. Among all composites, the optimal WMS-Si190- filled composite (mass ratio WMS:Si190=10:90, total filler loading 60wt%) exhibited the best mechanical performance including flexural strength, flexural modulus, compressive strength and Vickers microhardness. The incorporation of WMS and its mixed bimodal fillers with smaller silica particles led to the design and formulation of dental resin composites with superior mechanical properties. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  4. Bacterial adhesion on direct and indirect dental restorative composite resins: An in vitro study on a natural biofilm.

    Science.gov (United States)

    Derchi, Giacomo; Vano, Michele; Barone, Antonio; Covani, Ugo; Diaspro, Alberto; Salerno, Marco

    2017-05-01

    Both direct and indirect techniques are used for dental restorations. Which technique should be preferred or whether they are equivalent with respect to bacterial adhesion is unclear. The purpose of this in vitro study was to determine the affinity of bacterial biofilm to dental restorative composite resins placed directly and indirectly. Five direct composite resins for restorations (Venus Diamond, Adonis, Optifil, Enamel Plus HRi, Clearfil Majesty Esthetic) and 3 indirect composite resins (Gradia, Estenia, Signum) were selected. The materials were incubated in unstimulated whole saliva for 1 day. The biofilms grown were collected and their bacterial cells counted. In parallel, the composite resin surface morphology was analyzed with atomic force microscopy. Both bacterial cell count and surface topography parameters were subjected to statistical analysis (α=.05). Indirect composite resins showed significantly lower levels than direct composite resins for bacterial cell adhesion, (Pcomposite resins (P>.05). However, within the indirect composite resins a significantly lower level was found for Gradia than Estenia or Signum (Pcomposite resin roughness and bacterial adhesion when the second and particularly the third-order statistical moments of the composite resin height distributions were considered. Indirect dental restorative composite resins were found to be less prone to biofilm adhesion than direct composite resins. A correlation of bacterial adhesion to surface morphology exists that is described by kurtosis; thus, advanced data analysis is required to discover possible insights into the biologic effects of morphology. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  5. Synthesis of iodine-containing cyclophosphazenes for using as radiopacifiers in dental composite resin

    International Nuclear Information System (INIS)

    Zhao, Yuchen; Lan, Jinle; Wang, Xiaoyan; Deng, Xuliang; Cai, Qing; Yang, Xiaoping

    2014-01-01

    In this study, a strategy of using iodine-containing cyclophosphazenes as radiopacifiers for dental composite resin was evaluated. It was hypothesized that cyclophosphazenes bearing both iodine and acrylate group swere able to endow composite resins radiopacity without compromising mechanical properties. The cyclophosphazene compounds were synthesized by subsequently nucleophilic substitution of hexachlorocyclotriphosphazene with hydroxyethyl methacrylate (HEMA) and 4-iodoaniline. Cyclotriphosphazenes containing two different molar ratios of HEMA to 4-iodoaniline (1:5 and 2:4) were obtained, and were identified with 1 H NMR, FT-IR, UV and mass spectroscopy. The iodine-containing cyclophosphazenes were able to dissolve well in bisphenol A glycidyl methacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) resin, and were added at two contents (10 or 15%wt. of the resin). The resins were photo-cured and post-thermal treated before characterizations. The resulting composite resins demonstrated the ability of blocking X-ray. And the addition of HEMA-co-iodoaniline substituted cyclotriphosphazenes caused minor adverse effect on the mechanical properties of the resins because the cyclotriphosphazenes could mix well and react with the resins. The presence of rigid phosphazene rings between resin backbones displayed an effective function of decreasing polymerization shrinkage. In summary, soluble and reactive iodine-containing cyclotriphosphazenes demonstrated advantages over traditional heavy metals or metal oxides in being used as additives for producing radiopaque dental resins. - Highlights: • Iodine-containing cyclotriphosphazenes were prepared via nucleophilic substitution. • The cyclotriphosphazenes endowed Bis-GMA/TEGDMA resins radiopacity. • The cyclotriphosphazenes caused a minor adverse effect on mechanical properties

  6. Synthesis of iodine-containing cyclophosphazenes for using as radiopacifiers in dental composite resin

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yuchen; Lan, Jinle [State Key Laboratory of Organic–Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Wang, Xiaoyan; Deng, Xuliang [Department of Geriatric Dentistry, Peking University School and Hospital of Stomatology, Beijing 100081 (China); Cai, Qing, E-mail: caiqing@mail.buct.edu.cn [State Key Laboratory of Organic–Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Laboratory of Biomedical Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Yang, Xiaoping [State Key Laboratory of Organic–Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Laboratory of Biomedical Materials, Beijing University of Chemical Technology, Beijing 100029 (China)

    2014-10-01

    In this study, a strategy of using iodine-containing cyclophosphazenes as radiopacifiers for dental composite resin was evaluated. It was hypothesized that cyclophosphazenes bearing both iodine and acrylate group swere able to endow composite resins radiopacity without compromising mechanical properties. The cyclophosphazene compounds were synthesized by subsequently nucleophilic substitution of hexachlorocyclotriphosphazene with hydroxyethyl methacrylate (HEMA) and 4-iodoaniline. Cyclotriphosphazenes containing two different molar ratios of HEMA to 4-iodoaniline (1:5 and 2:4) were obtained, and were identified with {sup 1}H NMR, FT-IR, UV and mass spectroscopy. The iodine-containing cyclophosphazenes were able to dissolve well in bisphenol A glycidyl methacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) resin, and were added at two contents (10 or 15%wt. of the resin). The resins were photo-cured and post-thermal treated before characterizations. The resulting composite resins demonstrated the ability of blocking X-ray. And the addition of HEMA-co-iodoaniline substituted cyclotriphosphazenes caused minor adverse effect on the mechanical properties of the resins because the cyclotriphosphazenes could mix well and react with the resins. The presence of rigid phosphazene rings between resin backbones displayed an effective function of decreasing polymerization shrinkage. In summary, soluble and reactive iodine-containing cyclotriphosphazenes demonstrated advantages over traditional heavy metals or metal oxides in being used as additives for producing radiopaque dental resins. - Highlights: • Iodine-containing cyclotriphosphazenes were prepared via nucleophilic substitution. • The cyclotriphosphazenes endowed Bis-GMA/TEGDMA resins radiopacity. • The cyclotriphosphazenes caused a minor adverse effect on mechanical properties.

  7. Single color attribute index for shade conformity judgment of dental resin composites

    Directory of Open Access Journals (Sweden)

    Yong-Keun Lee

    2015-01-01

    Full Text Available Introduction: Commercial dental resin composites under the same shade designations show color discrepancies by brand. Moreover, three Commission Internationale de l′Eclairage (CIE color coordinates show significant variations by measurement method; therefore, direct comparisons of the color coordinates based on different methods are meaningless. This study aimed to assess a hypothesis that a new color attribute index (CAI, which could reduce the color coordinate variations by measurement method, was applicable for the shade conformity judgment of dental resin composites. The Hypothesis: CAI is applicable in the shade conformity judgment of commercial dental resin composites. Using the CIE color coordinates of shade guide tabs and resin composites, combined color indices such as Wa = CIE aFNx01 × DEFNx01 ab /C ab FNx01 and Wb = CIE bFNx01 × DEFNx01 ab /C ab FNx01 were defined, in which DEFNx01 ab was the color difference with a standard white tile. Ratio of Wa/Wb to that of an arbitrary reference shade (A2 in the same brand and measurement was defined as the CAI. The CAI values were significantly different by the shade designation and showed a logical trend by the shade designation number. The CAI of commercial resin composites and the keyed shade guide tabs showed overlaps. Evaluation of the Hypothesis: The CAI might be used to judge the shade conformity of resin composites using the values based on different measurement methods. The application of the CAI, instead of conventional three-color coordinates, could efficiently simplify the shade conformity judgment of commercial resin composites. Although the hypothesis of the present study was partially confirmed, further studies for the practical application of this index are highly recommended.

  8. Direct spectrometry: a new alternative for measuring the fluorescence of composite resins and dental tissues.

    Science.gov (United States)

    da Silva, Tm; de Oliveira, Hpm; Severino, D; Balducci, I; Huhtala, Mfrl; Gonçalves, Sep

    2014-01-01

    The aim of this study was to evaluate the fluorescence intensity of different composite resins and compare those values with the fluorescence intensity of dental tissues. Different composite resins were used to make 10 discs (2 mm in depth and 4 mm in diameter) of each brand, divided into groups: 1) Z (Filtek Z350, 3M ESPE), 2) ES (Esthet-X, Dentsply), 3) A (Amelogen Plus, Ultradent), 4) DVS (Durafill-VS, Heraeus Kulzer) with 2 mm composite resin for enamel (A2), 5) OES ([Esthet-X] opaque-OA [1 mm] + enamel-A2 [1 mm]); 6) ODVSI ([Charisma-Opal/Durafill-VSI], opaque-OM (1 mm) + translucent [1mm]), and 7) DVSI ([Durafill- VSI] translucent [2 mm]). Dental tissue specimens were obtained from human anterior teeth cut in a mesiodistal direction to obtain enamel, dentin, and enamel/dentin samples (2 mm). The fluorescence intensity of specimens was directly measured using an optic fiber associated with a spectrometer (Ocean Optics USB 4000) and recorded in graphic form (Origin 8.0 program). Data were submitted to statistical analysis using Dunnet, Tukey, and Kruskall-Wallis tests. Light absorption of the composite resins was obtained in a spectral range from 250 to 450 nm, and that of dental tissues was between 250 and 300 nm. All composite resins were excited at 398 nm and exhibited maximum emissions of around 485 nm. Fluorescence intensity values for all of the resins showed statistically significant differences (measured in arbitrary units [AUs]), with the exception of groups Z and DVS. Group DVSI had the highest fluorescence intensity values (13539 AU), followed by ODVS (10440 AU), DVS (10146 AU), ES (3946 AU), OES (3841 AU), A (3540 AU), and Z (1146 AU). The fluorescence intensity values for the composite resins differed statistically from those of dental tissues (E=1380 AU; D=6262 AU; E/D=3251 AU). The opacity interfered with fluorescence intensity, and group Z demonstrated fluorescence intensity values closest to that of tooth enamel. It is concluded that the

  9. Do Dental Resin Composites Accumulate More Oral Biofilms and Plaque than Amalgam and Glass Ionomer Materials?

    Directory of Open Access Journals (Sweden)

    Ning Zhang

    2016-11-01

    Full Text Available A long-time drawback of dental composites is that they accumulate more biofilms and plaques than amalgam and glass ionomer restorative materials. It would be highly desirable to develop a new composite with reduced biofilm growth, while avoiding the non-esthetics of amalgam and low strength of glass ionomer. The objectives of this study were to: (1 develop a protein-repellent composite with reduced biofilms matching amalgam and glass ionomer for the first time; and (2 investigate their protein adsorption, biofilms, and mechanical properties. Five materials were tested: A new composite containing 3% of protein-repellent 2-methacryloyloxyethyl phosphorylcholine (MPC; the composite with 0% MPC as control; commercial composite control; dental amalgam; resin-modified glass ionomer (RMGI. A dental plaque microcosm biofilm model with human saliva as inoculum was used to investigate metabolic activity, colony-forming units (CFU, and lactic acid production. Composite with 3% MPC had flexural strength similar to those with 0% MPC and commercial composite control (p > 0.1, and much greater than RMGI (p < 0.05. Composite with 3% MPC had protein adsorption that was only 1/10 that of control composites (p < 0.05. Composite with 3% MPC had biofilm CFU and lactic acid much lower than control composites (p < 0.05. Biofilm growth, metabolic activity and lactic acid on the new composite with 3% MPC were reduced to the low level of amalgam and RMGI (p > 0.1. In conclusion, a new protein-repellent dental resin composite reduced oral biofilm growth and acid production to the low levels of non-esthetic amalgam and RMGI for the first time. The long-held conclusion that dental composites accumulate more biofilms than amalgam and glass ionomer is no longer true. The novel composite is promising to finally overcome the major biofilm-accumulation drawback of dental composites in order to reduce biofilm acids and secondary caries.

  10. Trends in material choice for posterior restorations in an Israeli dental school: composite resin versus amalgam.

    Science.gov (United States)

    Ben-Gal, Gilad; Weiss, Ervin I

    2011-12-01

    According to a recent American Dental Association survey, posterior composite resin restorations now outnumber amalgam restorations in the United States. Dental schools around the world vary considerably in the extent to which they teach the use of composite resins. We aimed to determine if there has been an increase in the placement of posterior composite restorations in an Israeli dental school and if faculty experience affects the type of posterior restoration placed. In this retrospective study, we recorded and analyzed all the restorations performed by undergraduate students in the last five academic years at the Hebrew University Hadassah School of Dental Medicine in Jerusalem. All clinical records of student treatments between 2004 and 2009 were screened, and direct restorations were registered. Out of 6,094 posterior restorations performed during the study period, 42.3 percent were made of composite resin, increasing from 36.8 percent in 2004-05 to 48.5 percent in 2008-09, an increase of 11.7 percent. When clinical instructors were asked to state their preference if they themselves were to undergo posterior restoration, similar results were obtained. Instructors with less than ten years' experience preferred posterior composite resin restorations in 54.8 percent of the hypothetical situations, compared with 37.2 percent preferred by instructors with ten years of experience or more. It appears that the use of composite resin was influenced mainly by the prevailing trend and was not based on scientific evidence. Dental faculties should define criteria, based on up-to-date clinical studies, for using new materials, taking into consideration differences among instructors regarding treatment concept.

  11. Do Dental Resin Composites Accumulate More Oral Biofilms and Plaque than Amalgam and Glass Ionomer Materials?

    Science.gov (United States)

    Zhang, Ning; Melo, Mary A.S.; Weir, Michael D.; Reynolds, Mark A.; Bai, Yuxing; Xu, Hockin H.K.

    2016-01-01

    A long-time drawback of dental composites is that they accumulate more biofilms and plaques than amalgam and glass ionomer restorative materials. It would be highly desirable to develop a new composite with reduced biofilm growth, while avoiding the non-esthetics of amalgam and low strength of glass ionomer. The objectives of this study were to: (1) develop a protein-repellent composite with reduced biofilms matching amalgam and glass ionomer for the first time; and (2) investigate their protein adsorption, biofilms, and mechanical properties. Five materials were tested: A new composite containing 3% of protein-repellent 2-methacryloyloxyethyl phosphorylcholine (MPC); the composite with 0% MPC as control; commercial composite control; dental amalgam; resin-modified glass ionomer (RMGI). A dental plaque microcosm biofilm model with human saliva as inoculum was used to investigate metabolic activity, colony-forming units (CFU), and lactic acid production. Composite with 3% MPC had flexural strength similar to those with 0% MPC and commercial composite control (p > 0.1), and much greater than RMGI (p control composites (p control composites (p 0.1). In conclusion, a new protein-repellent dental resin composite reduced oral biofilm growth and acid production to the low levels of non-esthetic amalgam and RMGI for the first time. The long-held conclusion that dental composites accumulate more biofilms than amalgam and glass ionomer is no longer true. The novel composite is promising to finally overcome the major biofilm-accumulation drawback of dental composites in order to reduce biofilm acids and secondary caries. PMID:28774007

  12. Do Dental Resin Composites Accumulate More Oral Biofilms and Plaque than Amalgam and Glass Ionomer Materials?

    Science.gov (United States)

    Zhang, Ning; Melo, Mary A S; Weir, Michael D; Reynolds, Mark A; Bai, Yuxing; Xu, Hockin H K

    2016-11-01

    A long-time drawback of dental composites is that they accumulate more biofilms and plaques than amalgam and glass ionomer restorative materials. It would be highly desirable to develop a new composite with reduced biofilm growth, while avoiding the non-esthetics of amalgam and low strength of glass ionomer. The objectives of this study were to: (1) develop a protein-repellent composite with reduced biofilms matching amalgam and glass ionomer for the first time; and (2) investigate their protein adsorption, biofilms, and mechanical properties. Five materials were tested: A new composite containing 3% of protein-repellent 2-methacryloyloxyethyl phosphorylcholine (MPC); the composite with 0% MPC as control; commercial composite control; dental amalgam; resin-modified glass ionomer (RMGI). A dental plaque microcosm biofilm model with human saliva as inoculum was used to investigate metabolic activity, colony-forming units (CFU), and lactic acid production. Composite with 3% MPC had flexural strength similar to those with 0% MPC and commercial composite control ( p > 0.1), and much greater than RMGI ( p biofilm CFU and lactic acid much lower than control composites ( p Biofilm growth, metabolic activity and lactic acid on the new composite with 3% MPC were reduced to the low level of amalgam and RMGI ( p > 0.1). In conclusion, a new protein-repellent dental resin composite reduced oral biofilm growth and acid production to the low levels of non-esthetic amalgam and RMGI for the first time. The long-held conclusion that dental composites accumulate more biofilms than amalgam and glass ionomer is no longer true. The novel composite is promising to finally overcome the major biofilm-accumulation drawback of dental composites in order to reduce biofilm acids and secondary caries.

  13. Dynamic visco-elastic properties of dental composite resins.

    Science.gov (United States)

    Mesquita, Renata V; Axmann, Detlef; Geis-Gerstorfer, Jürgen

    2006-03-01

    This study aimed to examine the visco-elastic properties of dental composites by dynamic mechanical analysis under the influence of clinically relevant temperatures and variable frequencies, after being stored in air or distilled water for up to 3 months. Two direct (Diamond Lite and Grandio) and two indirect (Artglass and Vita Zeta LC) composites were used. Samples were immediately tested (baseline) or stored at 37 degrees C, either in air or distilled water for 1 day, 7 or 90 days before testing. During dynamic testing, elastic modulus, viscous modulus and loss tangent were determined over a frequency range from 0.1 to 10 Hz at constant temperatures between 5 and 55 degrees C. Results were analyzed by one-way ANOVA and Turkey's-test. Elastic and viscous moduli were higher for direct than for indirect composites. No such evidence was found for loss tangent. Only the elastic modulus showed statistically relevant differences in the direct and indirect materials groups: Grandio showed higher modulus than Diamond Lite, while Artglass had higher modulus than Vita Zeta LC. The elastic modulus reduced with increasing temperature and decreasing frequency, while the loss tangent showed the opposite trend. The influence of temperature and frequency on viscous modulus was not conclusive. The elastic modulus was more sensitive to moisture than viscous modulus and loss tangent but all three properties showed no overall consistent trend in the results following the storage periods. Dynamic mechanical analysis was a valuable tool to characterize the visco-elastic properties of dental composites, thus giving us a greater insight into material behavior.

  14. Antimicrobial and mechanical properties of dental resin composite containing bioactive glass.

    Science.gov (United States)

    Korkut, Emre; Torlak, Emrah; Altunsoy, Mustafa

    2016-07-26

    The aim of this study was to evaluate the antimicrobial efficacy and mechanical properties of dental resin composites containing different amounts of microparticulate bioactive glass (BAG). Experimental resin composites were prepared by mixing resin matrix (70% BisGMA and 30% TEGDMA) and inorganic filler with various fractions of BAG to achieve final BAG concentrations of 5, 10 and 30 wt%. Antimicrobial efficacy was assessed in aqueous suspension against Escherichia coli, Staphylococcus aureus and Streptococcus mutans and in biofilm against S. mutans. The effect of incorporation of BAG on the mechanical properties of resin composite was evaluated by measuring the surface roughness, compressive strength and flexural strength. Under the dynamic contact condition, viable counts of E. coli, S. aureus and S. mutans in suspensions were reduced up to 78%, 57% and 50%, respectively, after 90 minutes of exposure to disc-shaped composite specimens, depending on the BAG contents. In 2-day-old S. mutans biofilm, incorporation of BAG into composite at ratios of 10% and 30% resulted in 0.8 and 1.4 log reductions in the viable cell counts compared with the BAG-free composite, respectively. The surface roughness values of composite specimens did not show any significant difference (p>0.05) at any concentration of BAG. However, compressive and flexural strengths of composite were decreased significantly with addition of 30% BAG (p<0.05). The results demonstrated the successful utilization of BAG as a promising biomaterial in resin composites to provide antimicrobial function.

  15. Effect of bench time polymerization on depth of cure of dental composite resin

    Science.gov (United States)

    Harahap, K.; Yudhit, A.; Sari, F.

    2017-07-01

    The aim of this research was to investigate the effect of bench time before light cured polymerization on the depth of cure of dental composite resin. Nanofiller composite resin (Filtek Z350 XT,3M, ESPE,China) was used in this study. Sixty samples of nanofiller composite resin were made and divided into control and test groups with bench time for 0, 15, 30, 45, and 60 min. For the test group, composite resins were stored in refrigerator with 4°C temperatures. Meanwhile, for the control groups, the composite resin was stored at room temperature. The samples were prepared using metal mould with size diameter of 6 mm and 4 mm in thickness. Samples were cured for 20 s by using visible blue light curing unit. Part of samples that unpolymerized were removed by using a plastic spatula. The remaining parts of samples were measured by digital caliper and noted as depth of cure (mm). Data were analyzed to one-way ANOVA and LSD tests (p≤0.05). Results showed there was no significance differences between test groups (p=0.5). A 60 minutes bench time group showed the highest depth of cure value among test group, and it was almost similar with control group value. It can be concluded that longer bench time can increase the depth of cure of composite resin.

  16. Polymerization shrinkage assessment of dental resin composites: a literature review.

    Science.gov (United States)

    Kaisarly, Dalia; Gezawi, Moataz El

    2016-09-01

    Composite restorations are widely used worldwide, but the polymerization shrinkage is their main disadvantage that may lead to clinical failures and adverse consequences. This review reports, currently available in vitro techniques and methods used for assessing the polymerization shrinkage. The focus lies on recent methods employing three-dimensional micro-CT data for the evaluation of polymerization shrinkage: volumetric measurement and the shrinkage vector evaluation through tracing particles before and after polymerization. Original research articles reporting in vitro shrinkage measurements and shrinkage stresses were included in electronic and hand-search. Earlier methods are easier, faster and less expensive. The procedures of scanning the samples in the micro-CT and performing the shrinkage vector evaluation are time consuming and complicated. Moreover, the respective software is not commercially available and the various methods for shrinkage vector evaluation are based on different mathematical principles. Nevertheless, these methods provide clinically relevant information and give insight into the internal shrinkage behavior of composite applied in cavities and how boundary conditions affect the shrinkage vectors. The traditional methods give comparative information on polymerization shrinkage of resin composites, whereas using three-dimensional micro-CT data for volumetric shrinkage measurement and the shrinkage vector evaluation is a highly accurate method. The methods employing micro-CT data give the researchers knowledge related to the application method and the boundary conditions of restorations for visualizing the shrinkage effects that could not be seen otherwise. Consequently, this knowledge can be transferred to the clinical situation to optimize the material manipulation and application techniques for improved outcomes.

  17. Cytotoxic effects of bulk fill composite resins on human dental pulp stem cells.

    Science.gov (United States)

    Şişman, Reyhan; Aksoy, Ayça; Yalçın, Muhammet; Karaöz, Erdal

    2016-01-01

    Five bulk fill composite resins, including SDR, Tetric EvoCeram Bulk Fill (TEC), X-trafil (XTF), Sonic Fill (SF), Filtek Bulk Fill (FBF), were used in this study. Human dental pulp stem cells were cultured in 12-well culture dishes (3 × 104 cells per cm(2)) and stored in an incubator at 37°C and 5% CO2 for 1 day. On days 1, 7, 14, and 21 of co-culture, viable cells were measured using a WST-1 assay. Lower cell viability was observed with XTF and SDR bulk fill composite resins compared to the control group during the WST-1 assay. Although bulk fill composite resins provide advantages in practical applications, they are limited by their cytotoxic properties. (J Oral Sci 58, 299-305, 2016).

  18. Mechanical properties of dental resin composites by co-filling diatomite and nanosized silica particles

    International Nuclear Information System (INIS)

    Wang Hua; Zhu Meifang; Li Yaogang; Zhang Qinghong; Wang Hongzhi

    2011-01-01

    The aim of this study was to investigate the mechanical property effects of co-filling dental resin composites with porous diatomite and nanosized silica particles (OX-50). The purification of raw diatomite by acid-leaching was conducted in a hot 5 M HCl solution at 80 deg. C for 12 h. Both diatomite and nanosized SiO 2 were silanized with 3-methacryloxypropyltrimethoxysilane. The silanized inorganic particles were mixed into a dimethacrylate resin. Purified diatomite was characterized by X-ray diffraction, UV-vis diffuse reflectance spectroscopy and an N 2 adsorption-desorption isotherm. Silanized inorganic particles were characterized using Fourier transform infrared spectroscopy and a thermogravimetric analysis. The mechanical properties of the composites were tested by three-point bending, compression and Vicker's microhardness. Scanning electron microscopy was used to show the cross-section morphologies of the composites. Silanization of diatomite and nanosized silica positively reinforced interactions between the resin matrix and the inorganic particles. The mechanical properties of the resin composites gradually increased with the addition of modified diatomite (m-diatomite). The fracture surfaces of the composites exhibited large fracture steps with the addition of m-diatomite. However, when the mass fraction of m-diatomite was greater than 21 wt.% with respect to modified nanosized silica (mOX-50) and constituted 70% of the resin composite by weight, the mechanical properties of the resin composites started to decline. Thus, the porous structure of diatomite appears to be a crucial factor to improve mechanical properties of resin composites.

  19. Bisphenol A Release: Survey of the Composition of Dental Composite Resins.

    Science.gov (United States)

    Dursun, Elisabeth; Fron-Chabouis, Hélène; Attal, Jean-Pierre; Raskin, Anne

    2016-01-01

    Bisphenol A (BPA) is an endocrine disruptor with potential toxicity. Composite resins may not contain pure BPA, but its derivatives are widely used. Several studies found doses of BPA or its derivatives in saliva or urine of patients after composite resin placement. The aims of this study were to establish an exhaustive list of composite resins marketed in Europe and their composition, and to assess the extent of BPA derivatives used. A research on manufacturers' websites was performed to reference all composite resins marketed in Europe, then their composition was determined from both material safety data sheets and a standardized questionnaire sent to manufacturers. Manufacturers had to indicate whether their product contained the monomers listed, add other monomers if necessary, or indicate "not disclosed". 160 composite resins were identified from 31 manufacturers and 23 manufacturers (74.2%) responded to the survey. From the survey and websites, the composition of 130 composite resins (81.2%) was: 112 (86.2%) based on BPA derivatives, 97 (74.7%) on bis-GMA, 17 (13.1%) without monomer derived from BPA (UDMA, sometimes with TEGDMA) and 6 (4.6%) with UDMA (only); 1 (0.8%) did not contain a BPA derivative or UDMA or TEGDMA. Pure BPA was never reported. This work has established a list of 18 composite resins that contain no BPA derivative. Manufacturers should be required to report the exact composition of their products as it often remains unclear or incomplete.

  20. Temperature-dependence of creep behaviour of dental resin-composites.

    Science.gov (United States)

    El-Safty, S; Silikas, N; Watts, D C

    2013-04-01

    To determine the effect of temperature, over a clinically relevant range, on the creep behaviour of a set of conventional and flowable resin-composites including two subgroups having the same resin matrix and varied filler loading. Eight dental resin-composites: four flowable and four conventional were investigated. Stainless steel split moulds (4 mm × 6 mm) were used to prepare cylindrical specimens for creep examination. Specimens were irradiated in the moulds in layers of 2mm thickness (40s each), as well as from the radial direction after removal from the moulds, using a light-curing unit with irradiance of 650 mW/cm(2). A total of 15 specimens from each material were prepared and divided into three groups (n=5) according to the temperature; Group I: (23°C), Group II: (37°C) and Group III: (45°C). Each specimen was loaded (20 MPa) for 2h and unloaded for 2h. Creep was measured continuously over the loading and unloading periods. At higher temperatures greater creep and permanent set were recorded. The lowest mean creep occurred with GS and GH resin-composites. Percentage of creep recovery decreased at higher temperatures. At 23°C, the materials exhibited comparable creep. At 37°C and 45°C, however, there was a greater variation between materials. For all resin-composites, there was a strong linear correlation with temperature for both creep and permanent set. Creep parameters of resin-composites are sensitive to temperature increase from 23 to 45°C, as can occur intra-orally. For a given resin matrix, creep decreased with higher filler loading. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Rugometric and microtopographic non-invasive inspection in dental-resin composites and zirconia ceramics

    Science.gov (United States)

    Fernández-Oliveras, Alicia; Costa, Manuel F. M.; Pecho, Oscar E.; Rubiño, Manuel; Pérez, María. M.

    2013-11-01

    Surface properties are essential for a complete characterization of biomaterials. In restorative dentistry, the study of the surface properties of materials meant to replace dental tissues in an irreversibly diseased tooth is important to avoid harmful changes in future treatments. We have experimentally analyzed the surface characterization parameters of two different types of dental-resin composites and pre-sintered and sintered zirconia ceramics. We studied two shades of both composite types and two sintered zirconia ceramics: colored and uncolored. Moreover, a surface treatment was applied to one specimen of each dental-resin. All the samples were submitted to rugometric and microtopographic non-invasive inspection with the MICROTOP.06.MFC laser microtopographer in order to gather meaningful statistical parameters such as the average roughness (Ra), the root-mean-square deviation (Rq), the skewness (Rsk), and the kurtosis of the surface height distribution (Rku). For a comparison of the different biomaterials, the uncertainties associated to the surface parameters were also determined. With respect to Ra and Rq, significant differences between the composite shades were found. Among the dental resins, the nanocomposite presented the highest values and, for the zirconia ceramics, the pre-sintered sample registered the lowest ones. The composite performance may have been due to cluster-formation variations. Except for the composites with the surface treatment, the sample surfaces had approximately a normal distribution of heights. The surface treatment applied to the composites increased the average roughness and moved the height distribution farther away from the normal distribution. The zirconia-sintering process resulted in higher average roughness without affecting the height distribution.

  2. The effects of different opacifiers on the translucency of experimental dental composite resins.

    Science.gov (United States)

    Haas, Karine; Azhar, Gulelala; Wood, Duncan J; Moharamzadeh, Keyvan; van Noort, Richard

    2017-08-01

    The aim of this study was to evaluate the effects of different opacifiers on the translucency of experimental dental composite-resins. Three metal oxides that are used as opacifiers were tested in this study: titanium oxide (TiO 2 ), aluminium oxide (Al 2 O 3 ) and zirconium oxide (ZrO 2 ). Experimental composite-resins were fabricated containing 25wt.% urethane dimethacrylate (UDMA)-based resin matrix and 75% total filler including different concentrations of metal oxides (0, 0.25, 0.5, 0.75 and 1wt.%) blended into silane treated barium-silicate filler. The specimens (15.5mm diameter and 1mm thickness) were light-cured and tested in the transmittance mode using a UV/VIS spectrophotometer at wavelengths from 380 to 700nm under a standard illuminant D65. The color differences (ΔE* ab) between different concentrations of opacifiers were also measured in transmittance mode based on their Lab values. Statistical analysis by ANOVA and Tukey's test showed a significant decrease (pcomposite-resins. There was a linear correlation between different concentrations of TiO 2 and Al 2 O 3 and total transmittance. Total transmittance was also found to be wavelength dependent. The color differences for the concentrations of 0-1wt.% of the opacifiers were above 1 ΔE* unit, with Al 2 O 3 showing the smallest color shift. The type and the amount of the opacifiers used in this study had a significant effect on the translucency of the experimental UDMA-based dental composite resins. The most effective opacifier was TiO 2 , followed by ZrO 2 and Al 2 O 3 in decreasing order, respectively. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. Improving mechanical properties of flowable dental composite resin by adding silica nanoparticles

    Directory of Open Access Journals (Sweden)

    Baloš Sebastian

    2013-01-01

    Full Text Available Background/Aim. The main drawback of flowable dental composite resin is low strength compared to conventional composite resin, due to a low amount of filler, neccessary for achieving low viscosity and ease of handling. The aim of this study was to improve mechanical properties of flowable dental composite resin by adding small amount of nanoparticles, which would not compromise handling properties. Methods. A commercially available flowable dental composite resin material was mixed with 7 nm aftertreated hydrophobic fumed silica and cured by an UV lamp. Four sets of samples were made: control sample (unmodified, the sample containing 0.05%, 0.2% and 1% nanosilica. Flexural modulus, flexural strength and microhardness were tested. One-way ANOVA followed by Tukey’s test with the significance value of p < 0.05 was performed to statistically analyze the obtained results. Furthermore, differential scanning calorimetry (DSC and SEM analysis were performed. To asses handling properties, slumping resistance was determined. Results. It was found that 0.05% is the most effective nanosilica content. All the tested mechanical properties were improved by a significant margin. On the other hand, when 0.2% and 1% nanosilica content was tested, different results were obtained, some of the mechanical properties even dropped, while some were insignificantly improved. The difference between slumping resistance of unmodified and modified samples was found to be statistically insignificant. Conclusions. Low nanosilica addition proved more effective in improving mechanical properties compared to higher additions. Furthermore, handling properties are unaffected by nanosilica addition.

  4. Biomechanical model produced from light-activated dental composite resins: a holographic analysis

    Science.gov (United States)

    Pantelić, Dejan; Vasiljević, Darko; Blažić, Larisa; Savić-Šević, Svetlana; Murić, Branka; Nikolić, Marko

    2013-11-01

    Light-activated dental composites, commonly applied in dentistry, can be used as excellent material for producing biomechanical models. They can be cast in almost any shape in an appropriate silicone mold and quickly solidified by irradiation with light in the blue part of the spectrum. In that way, it is possible to obtain any number of nearly identical casts. The models can be used to study the behavior of arbitrary structure under mechanical loads. To test the technique, a simple mechanical model of the tooth with a mesio-occluso-distal cavity was manufactured. Composite resin restoration was placed inside the cavity and light cured. Real-time holographic interferometry was used to analyze the contraction of the composite resin and its effect on the surrounding material. The results obtained in the holographic experiment were in good agreement with those obtained using the finite element method.

  5. Effects of staining and bleaching on color change of dental composite resins.

    Science.gov (United States)

    Villalta, Patricia; Lu, Huan; Okte, Zeynep; Garcia-Godoy, Franklin; Powers, John M

    2006-02-01

    Discoloration of resin-based composites by colored solutions is a common problem. The use of bleaching agents for discolored natural teeth is becoming increasingly popular. It is not clear if bleaching agents can remove the stain from composite resins. The purpose of this study was to investigate the effects of 2 staining solutions and 3 bleaching systems on the color changes of 2 dental composite resins. Forty-five disk-shaped specimens (9 x 2.5 mm) of each of 2 composite resins, Filtek Supreme (FS) and Esthet X (EX), were prepared. The specimens were then divided into 3 groups of 15 specimens each and immersed in 2 staining solutions (coffee or red wine) or distilled water (control) for 3 hours daily over a 40-day test period. The 3 groups were then divided into 3 subgroups (n = 5), and 3 bleaching agents (Crest Night Effects, Colgate Simply White Night, or Opalescence Quick) were applied to the surface of the specimens over a 14-day period. Color of the specimens was measured with a spectrophotometer using CIELAB color space relative to CIE standard illuminant D55 at baseline, after staining, and after bleaching. The color differences (deltaE(ab)*) between the 3 measurements were calculated. The value deltaE(ab)* = 3.3 was used as an acceptable value in subjective visual evaluations. Analysis of variance and nonparametric analysis (Kruskal-Wallis test and Mann-Whitney test) were used to analyze the data. After staining, FS had more color change than EX and was more affected by the wine solution. After bleaching, the color of both EX and FS specimens returned to the baseline. The color differences between bleaching and baseline were less than value deltaE(ab)* = 3.3 for all groups. The nanocomposite (FS) changed color more than the microhybrid composite (EX) as a result of staining in coffee or red wine solutions. After bleaching, discoloration was removed completely from the composite resins tested.

  6. Twelve-year survival of 2-surface composite resin and amalgam premolar restorations placed by dental students.

    Science.gov (United States)

    Naghipur, Safa; Pesun, Igor; Nowakowski, Anthony; Kim, Aaron

    2016-09-01

    Composite resin and amalgam restorations are indicated for the restoration of posterior teeth. With increased esthetic demands, long-term clinical studies are required to evaluate the restorative success and reasons for failure of these materials. The purpose of this retrospective study was to determine the survival and reasons for failure of directly placed 2-surface composite resin restorations and directly placed 2-surface amalgam restorations on premolars placed by Canadian dental students. Using The University of Manitoba's dental management software and paper charts, all 2-surface composite resin and 2-surface amalgam restorations placed on premolars between January 1, 2002, and May 30, 2014, were included. Short-term failure (within 2 years), long-term failure, and reasons for failure were collected. A Kaplan-Meier survival estimate with an associated P value comparing composite resin to amalgam restoration curves was performed using SPSS statistical software. Over 12 years, 1695 composite resin and 1125 amalgam 2-surface premolar restorations were placed. Of these restorations, 134 composite resins (7.9%) and 66 amalgams (5.9%) failed. Short-term failures (2 years or less) consisted of 57 composite resin (4%) and 23 amalgam (2.3%) restorations. Long-term failures (greater than 2 years) consisted of 77 composite resin (4.5%) and 43 amalgam (3.8%) restorations. After 12 years of service, the survival probability of composite resin restorations was 86% and that of amalgam restorations 91.5%. The differences in composite resin and amalgam survival curves were also found to be statistically significant (P=.009 for Log-rank test). The main reasons for failure were recurrent caries and fracture of the tooth being restored. Within the limitations of this study, both composite resin and amalgam restorations had acceptable success rates and similar failure modes. Recurrent caries was still the most common reason for failure. Copyright © 2016 Editorial Council for

  7. Bacterial viability and physical properties of antibacterially modified experimental dental resin composites.

    Directory of Open Access Journals (Sweden)

    Stefan Rüttermann

    Full Text Available PURPOSE: To investigate the antibacterial effect and the effect on the material properties of a novel delivery system with Irgasan as active agent and methacrylated polymerizable Irgasan when added to experimental dental resin composites. MATERIALS AND METHODS: A delivery system based on novel polymeric hollow beads, loaded with Irgasan and methacrylated polymerizable Irgasan as active agents were used to manufacture three commonly formulated experimental resin composites. The non-modified resin was used as standard (ST. Material A contained the delivery system providing 4 % (m/m Irgasan, material B contained 4 % (m/m methacrylated Irgasan and material C 8 % (m/m methacrylated Irgasan. Flexural strength (FS, flexural modulus (FM, water sorption (WS, solubility (SL, surface roughness Ra, polymerization shrinkage, contact angle Θ, total surface free energy γS and its apolar γS (LW, polar γS (AB, Lewis acid γS (+and base γS (- term as well as bacterial viability were determined. Significance was p < 0.05. RESULTS: The materials A to C were not unacceptably influenced by the modifications and achieved the minimum values for FS, WS and SL as requested by EN ISO 4049 and did not differ from ST what was also found for Ra. Only A had lower FM than ST. Θ of A and C was higher and γS (AB of A and B was lower than of ST. Materials A to C had higher γS (+ than ST. The antibacterial effect of materials A to C was significantly increased when compared with ST meaning that significantly less vital cells were found. CONCLUSION: Dental resin composites with small quantities of a novel antibacterially doped delivery system or with an antibacterial monomer provided acceptable physical properties and good antibacterial effectiveness. The sorption material being part of the delivery system can be used as a vehicle for any other active agent.

  8. Are linear elastic material properties relevant predictors of the cyclic fatigue resistance of dental resin composites?

    Science.gov (United States)

    Belli, Renan; Petschelt, Anselm; Lohbauer, Ulrich

    2014-04-01

    The aim of this study was to measure the linear elastic material properties of direct dental resin composites and correlate them with their fatigue strength under cyclic loading. Bar specimens of twelve resin composites were produced according to ISO 4049 and tested for elastic modulus (Emod) in 3-point bending (n=10), flexural strength (FS) (n=15) and single-edge-notch-beam fracture toughness (FT) (n=15), both in 4-point bending. Using the same specimen geometry, the flexural fatigue strength (FFS) was determined using the staircase approach after 10(4) cycles at 0.5 Hz in 4-point bending (n=25). The observation of the fracture surface and fracture profiles was conducted using a scanning electron microscope in order to evaluate the respective fracture mechanisms according to the two different loading conditions. Materials were ranked differently according to the tested parameters. Only weak correlations were found between any of the initial properties and FFS or strength loss. The best correlation to FFS was found to be the Emod (r(2)=0.679), although only slightly. Crack path in both loading conditions was mainly interparticle, with the crack propagating mainly within the matrix phase for fatigued specimens and eventually through the filler/matrix interface for statically loaded specimens. Fracture of large particles or prepolymerized fillers was only observed in specimens of FS and FT. Initial properties were better associated with microstructural features, whereas the fatigue resistance showed to be more dependent on aspects relating to the matrix phase. Our results show that linear elastic properties such as elastic modulus, flexural strength and fracture toughness are not good descriptors of the fatigue resistance of dental resin composite under cyclic bending, and may therefore have limited clinical relevance. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  9. Mechanical fatigue degradation of ceramics versus resin composites for dental restorations.

    Science.gov (United States)

    Belli, Renan; Geinzer, Eva; Muschweck, Anna; Petschelt, Anselm; Lohbauer, Ulrich

    2014-04-01

    For posterior partial restorations an overlap of indication exists where either ceramic or resin-based composite materials can be successfully applied. The aim of this study was to compare the fatigue resistance of modern dental ceramic materials versus dental resin composites in order to address such conflicts. Bar specimens of five ceramic materials and resin composites were produced according to ISO 4049 and stored for 14 days in distilled water at 37°C. The following ceramic materials were selected for testing: a high-strength zirconium dioxide (e.max ZirCAD, Ivoclar), a machinable lithium disilicate (e.max CAD, Ivoclar), a pressable lithium disilicate ceramic (e-max Press, Ivoclar), a fluorapatite-based glass-ceramic (e.max Ceram, Ivoclar), and a machinable color-graded feldspathic porcelain (Trilux Forte, Vita). The composite materials selected were: an indirect machinable composite (Lava Ultimate, 3M ESPE) and four direct composites with varying filler nature (Clearfil Majesty Posterior, Kuraray; GrandioSO, Voco; Tetric EvoCeram, Ivoclar-Vivadent; and CeramX Duo, Dentsply). Fifteen specimens were tested in water for initial strength (σin) in 4-point bending. Using the same test set-up, the residual flexural fatigue strength (σff) was determined using the staircase approach after 10(4) cycles at 0.5 Hz (n=25). Weibull parameters σ0 and m were calculated for the σin specimens, whereas the σff and strength loss in percentage were obtained from the fatigue experiment. The zirconium oxide ceramic showed the highest σin and σff (768 and 440 MPa, respectively). Although both lithium disilicate ceramics were similar in the static test, the pressable version showed a significantly higher fatigue resistance after cyclic loading. Both the fluorapatite-based and the feldspathic porcelain showed equivalent initial and cyclic fatigue properties. From the composites, the highest filled direct material Clearfil Majesty Posterior showed superior fatigue performance

  10. Resin composites

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

    2014-01-01

    OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

  11. Reduction of bacterial adhesion on dental composite resins by silicon–oxygen thin film coatings

    International Nuclear Information System (INIS)

    Mandracci, Pietro; Pirri, Candido F; Mussano, Federico; Ceruti, Paola; Carossa, Stefano

    2015-01-01

    Adhesion of bacteria on dental materials can be reduced by modifying the physical and chemical characteristics of their surfaces, either through the application of specific surface treatments or by the deposition of thin film coatings. Since this approach does not rely on the use of drugs or antimicrobial agents embedded in the materials, its duration is not limited by their possible depletion. Moreover it avoids the risks related to possible cytotoxic effects elicited by antibacterial substances released from the surface and diffused in the surrounding tissues. In this work, the adhesion of Streptococcus mutans and Streptococcus mitis was studied on four composite resins, commonly used for manufacturing dental prostheses. The surfaces of dental materials were modified through the deposition of a-SiO x thin films by plasma enhanced chemical vapor deposition. The chemical bonding structure of the coatings was analyzed by Fourier-transform infrared spectroscopy. The morphology of the dental materials before and after the coating deposition was assessed by means of optical microscopy and high-resolution mechanical profilometry, while their wettability was investigated by contact angle measurements. The sample roughness was not altered after coating deposition, while a noticeable increase of wettability was detected for all the samples. Also, the adhesion of S. mitis decreased in a statistically significant way on the coated samples, when compared to the uncoated ones, which did not occur for S. mutans. Within the limitations of this study, a-SiO x coatings may affect the adhesion of bacteria such as S. mitis, possibly by changing the wettability of the composite resins investigated. (paper)

  12. Reduction of bacterial adhesion on dental composite resins by silicon-oxygen thin film coatings.

    Science.gov (United States)

    Mandracci, Pietro; Mussano, Federico; Ceruti, Paola; Pirri, Candido F; Carossa, Stefano

    2015-01-29

    Adhesion of bacteria on dental materials can be reduced by modifying the physical and chemical characteristics of their surfaces, either through the application of specific surface treatments or by the deposition of thin film coatings. Since this approach does not rely on the use of drugs or antimicrobial agents embedded in the materials, its duration is not limited by their possible depletion. Moreover it avoids the risks related to possible cytotoxic effects elicited by antibacterial substances released from the surface and diffused in the surrounding tissues. In this work, the adhesion of Streptococcus mutans and Streptococcus mitis was studied on four composite resins, commonly used for manufacturing dental prostheses. The surfaces of dental materials were modified through the deposition of a-SiO(x) thin films by plasma enhanced chemical vapor deposition. The chemical bonding structure of the coatings was analyzed by Fourier-transform infrared spectroscopy. The morphology of the dental materials before and after the coating deposition was assessed by means of optical microscopy and high-resolution mechanical profilometry, while their wettability was investigated by contact angle measurements. The sample roughness was not altered after coating deposition, while a noticeable increase of wettability was detected for all the samples. Also, the adhesion of S. mitis decreased in a statistically significant way on the coated samples, when compared to the uncoated ones, which did not occur for S. mutans. Within the limitations of this study, a-SiO(x) coatings may affect the adhesion of bacteria such as S. mitis, possibly by changing the wettability of the composite resins investigated.

  13. Stickiness of dental resin composite materials to steel, dentin and bonded dentin.

    Science.gov (United States)

    Ertl, Kathrin; Graf, Alexandra; Watts, David; Schedle, Andreas

    2010-01-01

    Stickiness is a vital rheological parameter for the clinical handling behavior of unset resin composite restoratives. The aim of this study was to investigate the stickiness of three different resin composites at 23 degrees C and 37 degrees C tested on steel, dentin and dentin covered with different bonding agents. The stickiness instrument, used in this study consists of a vertical cylindrical stainless steel rod, with a flat circular end, and a platform with a cylindrical mold (diameter: 6.1mm, depth: 2.2mm). The test-material surface temperature and the speed of the rod can be modified. It moves slowly into the prepared mold which is filled with unset composite materials. The degree of stickiness is deducted from the height of the "elevation" the material forms when the plunger is withdrawn from the mold until the steelhead detaches itself from the composite. In this study, stickiness was tested directly to the steel plunger and to dentin slices (uncovered or covered with two different bonding agents) fixed to the plunger rod with a clamp. The coefficients of variation (CVs) were generally less than 0.10, indicating that the stickiness instrument offers an adequately reproducible way of testing stickiness. The tested composite materials varied significantly in stickiness. For all investigated materials a decrease of peak heights with increasing speed was found (for all three materials: psteel and least on bonded dentin. The order of stickiness of composites was not affected by testing the stickiness on the different materials. This method allows the characterization of composite resin materials stickiness to steel, as equivalent to dental steel instruments, and to bonded dentin as equivalent to the tooth cavity after preparation. An ideal material should have a sufficient difference between stickiness on steel and dentin so that it remains in the cavity and is not pulled back by the steel instrument.

  14. Nanoindentation creep versus bulk compressive creep of dental resin-composites.

    Science.gov (United States)

    El-Safty, S; Silikas, N; Akhtar, R; Watts, D C

    2012-11-01

    To evaluate nanoindentation as an experimental tool for characterizing the viscoelastic time-dependent creep of resin-composites and to compare the resulting parameters with those obtained by bulk compressive creep. Ten dental resin-composites: five conventional, three bulk-fill and two flowable were investigated using both nanoindentation creep and bulk compressive creep methods. For nano creep, disc specimens (15mm×2mm) were prepared from each material by first injecting the resin-composite paste into metallic molds. Specimens were irradiated from top and bottom surfaces in multiple overlapping points to ensure optimal polymerization using a visible light curing unit with output irradiance of 650mW/cm(2). Specimens then were mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. Following grinding and polishing, specimens were stored in distilled water at 37°C for 24h. Using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius), the nano creep was measured at a maximum load of 10mN and the creep recovery was determined when each specimen was unloaded to 1mN. For bulk compressive creep, stainless steel split molds (4mm×6mm) were used to prepare cylindrical specimens which were thoroughly irradiated at 650mW/cm(2) from multiple directions and stored in distilled water at 37°C for 24h. Specimens were loaded (20MPa) for 2h and unloaded for 2h. One-way ANOVA, Levene's test for homogeneity of variance and the Bonferroni post hoc test (all at p≤0.05), plus regression plots, were used for statistical analysis. Dependent on the type of resin-composite material and the loading/unloading parameters, nanoindentation creep ranged from 29.58nm to 90.99nm and permanent set ranged from 8.96nm to 30.65nm. Bulk compressive creep ranged from 0.47% to 1.24% and permanent set ranged from 0.09% to 0.38%. There was a significant (p=0.001) strong positive non-linear correlation (r(2)=0.97) between bulk

  15. Effect of the Purple Corn Beverage “Chicha Morada” in Composite Resin during Dental Bleaching

    Directory of Open Access Journals (Sweden)

    Eric Dario Acuña

    2016-01-01

    Full Text Available During dental bleaching the staining potential of the surface would increase. This study aims to evaluate the staining susceptibility of one bleached composite resin after the exposure to three different beverages: Peruvian purple corn based beverage (chicha morada, green tea, and distilled water. Thirty disk-shaped specimens of one nanofill composite resin were prepared. The specimens were then divided into six groups (n=5: purple corn (P, purple corn + bleaching (PB, green tea (T, green tea + bleaching (TB, distilled water (W, and distilled water + bleaching (WB. In groups that received bleaching, two sessions of bleaching with 35% hydrogen peroxide were done. Following bleaching, specimens were exposed to each liquid thirty minutes daily. Color was measured with a digital spectrophotometer. For statistical analysis, color measurement differences between the obtained results were used: during bleaching, after bleaching, and during + after bleaching. Two-way ANOVA was used to compare the color changes in the resins of all groups (p3.3.

  16. Influence of aging solutions on wear resistance and hardness of selected resin-based dental composites.

    Science.gov (United States)

    Chladek, Grzegorz; Basa, Katarzyna; Żmudzki, Jarosław; Malara, Piotr; Nowak, Agnieszka J; Kasperski, Jacek

    2016-01-01

    The purpose of this study was to investigate the effect of different plasticizing aging solutions on wear resistance and hardness of selected universal resin-based dental composites. Three light cured (one nanofilled, two microhybride) and one hybride chemical cured composites were aged at 37 °C for 48 h in distillated water, ethyl alcohol solution or Listerine mouthwash. After aging the microhardness tests were carried out and then tribological tests were performed in the presence of aging solution at 37 °C. During wear testing coefficients of friction were determined. The maximal vertical loss in micrometers was determined with profilometer. Aging in all liquids resulted in a significant decrease in hardness of the test materials, with the largest values obtained successively in ethanol solution, mouthwash and water. The effect of the liquid was dependent on the particular material, but not the type of material (interpreted as the size of filler used). Introduction of mouthwash instead of water or ethanol solution resulted in a significant reduction in the coefficient of friction. The lowest wear resistance was registered after aging in ethanol and for the chemical cured hybrid composite, but the vertical loss was strongly material dependent. The effect of different aging solution, including commercial mouthrinse, on hardness and wear was material dependent, and cannot be deduced from their category or filler loading. There is no simple correlation between hardness of resin-based dental composites and their wear resistance, but softening of particular composites materials during aging leads to the reduction of its wear resistance.

  17. Analytical methods for the measurement of polymerization kinetics and stresses of dental resin-based composites: A review

    Directory of Open Access Journals (Sweden)

    Mehrsima Ghavami-Lahiji

    2017-01-01

    Full Text Available Resin-based composites are commonly used restorative materials in dentistry. Such tooth-colored restorations can adhere to the dental tissues. One drawback is that the polymerization shrinkage and induced stresses during the curing procedure is an inherent property of resin composite materials that might impair their performance. This review focuses on the significant developments of laboratory tools in the measurement of polymerization shrinkage and stresses of dental resin-based materials during polymerization. An electronic search of publications from January 1977 to July 2016 was made using ScienceDirect, PubMed, Medline, and Google Scholar databases. The search included only English-language articles. Only studies that performed laboratory methods to evaluate the amount of the polymerization shrinkage and/or stresses of dental resin-based materials during polymerization were selected. The results indicated that various techniques have been introduced with different mechanical/physical bases. Besides, there are factors that may contribute the differences between the various methods in measuring the amount of shrinkages and stresses of resin composites. The search for an ideal and standard apparatus for measuring shrinkage stress and volumetric polymerization shrinkage of resin-based materials in dentistry is still required. Researchers and clinicians must be aware of differences between analytical methods to make proper interpretation and indications of each technique relevant to a clinical situation.

  18. Effect of light intensity and irradiation time on the polymerization process of a dental composite resin

    Directory of Open Access Journals (Sweden)

    Discacciati José Augusto César

    2004-01-01

    Full Text Available Polymerization shrinkage is a critical factor affecting the longevity and acceptability of dental composite resins. The aim of this work was to evaluate the effect of light intensity and irradiation time on the polymerization process of a photo cured dental composite resin by measuring the Vickers hardness number (VHN and the volumetric polymerization shrinkage. Samples were prepared using a dental manual light-curing unit. The samples were submitted to irradiation times of 5, 10, 20 and 40 s, using 200 and 400 mW.cm-2 light intensities. Vickers hardness number was obtained at four different moments after photoactivation (immediate, 1 h, 24 h and 168 h. After this, volumetric polymerization shrinkage values were obtained through a specific density method. The values were analyzed by ANOVA and Duncan's (p = 0.05. Results showed increase in hardness values from the immediate reading to 1 h and 24 h readings. After 24 h no changes were observed regardless the light intensities or activation times. The hardness values were always smaller for the 200 mW.cm-2 light intensity, except for the 40 s irradiation time. No significant differences were detected in volumetric polymerization shrinkage considering the light intensity (p = 0.539 and the activation time (p = 0.637 factors. In conclusion the polymerization of the material does not terminate immediately after photoactivation and the increase of irradiation time can compensate a lower light intensity. Different combinations between light intensity and irradiation time, i.e., different amounts of energy given to the system, have not affected the polymerization shrinkage.

  19. [Dental plaque microcosm biofilm behavior on a resin composite incorporated with nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt].

    Science.gov (United States)

    Junling, Wu; Qiang, Zhang; Ruinan, Sun; Ting, Zhu; Jianhua, Ge; Chuanjian, Zhou

    2015-12-01

    To develop a resin composite incorporated with nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt, and to measure its effect on human dental plaque microcosm biofilm. A novel nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt was synthesized according to methods introduced in previous research. Samples of the novel nano-antibacterial inorganic fillers were modified by a coupling agent and then added into resin composite at 0%, 5%, 10%, 15% or 20% mass fractions; 0% composite was used as control. A flexural test was used to measure resin composite mechanical properties. Results showed that a dental plaque microcosm biofilm model with human saliva as inoculum was formed. Colony-forming unit (CFU) counts, lactic acid production, and live/dead assay of biofilm on the resin composite were calculated to test the effect of the resin composite on human dental plaque microcosm biofilm. The incorporation of nano-antibacterial inorganic fillers with as much as 15% concentration into the resin composite showed no adverse effect on the mechanical properties of the resin composite (P > 0.05). Resin composite containing 5% or more nano-antibacterial inorganic fillers significantly inhibited the metabolic activity of dental plaque microcosm biofilm, suggesting its strong antibacterial potency (P < 0.05). This novel resin composite exhibited a strong antibacterial property upon the addition of up to 5% nano-antibacterial inorganic fillers, thereby leading to effective caries inhibition in dental application.

  20. Curing efficiency of dental resin composites formulated with camphorquinone or trimethylbenzoyl-diphenyl-phosphine oxide.

    Science.gov (United States)

    Schneider, Luis Felipe J; Cavalcante, Larissa Maria; Prahl, Scott A; Pfeifer, Carmem S; Ferracane, Jack L

    2012-04-01

    Since photoinitiator systems for dental resins based on camphorquinone (CQ) present color disadvantages, trimethylbenzoyl-diphenyl-phosphine oxide (TPO) has been proposed as an alternative. However, there are remaining considerations about its curing efficiency. The aims of the present investigation were: to characterize the relationship between the photoinitiator absorption spectra and the light spectrum emitted from a QTH light (absorbed power density, PD(abs)); to evaluate the kinetics of polymerization, and the depth of cure for filled dimethacrylate resins formulated with different photoinitiator systems. CQ+EDMAB (control); TPO and TPO+EDMAB were used in 50:50 Bis-GMA/TEGDMA resins. Photoinitiator absorption and QTH-light emission were evaluated using a spectrophotometer and kinetics of polymerization with differential scanning calorimetry (DSC) (n=3). Depth of cure was analyzed by the scraping method (n=5), as recommended by ISO4049. One-way ANOVA/Tukey's (p<0.05) was used to analyze the results. CQ presented higher PD(abs) than TPO (364 and 223 mW/cm(3), respectively). The DSC revealed that TPO and TPO+EDMAB produced a faster reaction than CQ+EDMAB. Composite formulated with CQ+EDMAB produced higher depth of cure (6.3±0.4 mm) than those with TPO (4.3±0.1) or TPO+EDMAB (4.2±0.3). Although CQ presented higher PD(abs) than TPO, formulations containing TPO exhibited higher reactivity than that with CQ. On the other hand, materials formulated with TPO demonstrated lower depth of cure than that with CQ. Therefore, its use as an alternative photoinitiator requires further investigation, with higher concentrations. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  1. Effects of silane-modified fillers on properties of dental composite resin.

    Science.gov (United States)

    Aydınoğlu, Aysu; Yoruç, Afife Binnaz Hazar

    2017-10-01

    The effect of silanization on the mechanical, chemical, and physical properties of dental composites was investigated. Silica fillers were obtained from colloidal silica solution, Ludox® HS-40 and they were silanized by using 3-methacryloxypropyl trimethoxysilane (MPTMS) in an acidic media. Mineralogical and chemical structures of unsilanized and silanized fillers were determined by using XRD and FT-IR analyses. The modification of unsilanized/silanized fillers were investigated by performing XPS and TGA analyses. The morphological evaluations, surface area, and particle size measurements were performed by using SEM, BET, and Zeta-Sizer, respectively. Eventually, pure and amorphous silica fillers were obtained. Furthermore, the weight percentage of the silane in silica/silane structure was compatible with theoretical values. SEM images, surface area, and particle size measurements showed that agglomeration tendencies of silanized fillers were lower compared to silanized fillers because of the MPTMS addition. Experimental composites (5/10/10/5BisGMA/HEMA/UDMA/TEGDMA resin reinforced with 70wt% silanized/unsilanized SiO 2 ) were fabricated into 4mm diameter×6mm thick discs for compressive strength (CS), angular flexural strength (AFS), curing depth (CD), and polymerization shrinkage (PS) on a 25×2×2mm rectangular Teflon mold for flexural strength (FS) and modulus of elasticity (E) tests. The curing depth (CD) and degree of polymerization percentage (DP) of composites were determined. Consequently, results showed that mechanical properties and DP of composite resins can be greatly influenced by silanization as a result of the organic matrix-inorganic filler interface bonding formed by silane structures. Despite of these findings, silanization of the SiO 2 was not effected DC and PS values. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Fracture strength and fatigue resistance of dental resin-based composites

    NARCIS (Netherlands)

    Keulemans, F.; Palav, P.; Aboushelib, M.M.N.; van Dalen, A.; Kleverlaan, C.J.; Feilzer, A.J.

    2009-01-01

    Objectives: The aim of this study was to evaluate in vitro the influence of fiber-reinforcement on the fracture strength and fatigue resistance of resin-based composites. Methods: One hundred rectangular bar-shaped specimens (2 mm × 2 mm × 25 mm) made of resin-based composite were prepared in a

  3. Detection of composite resin restorations using an ultraviolet light-emitting diode flashlight during forensic dental identification.

    Science.gov (United States)

    Guzy, Gerald; Clayton, Mary Ann

    2013-06-01

    With the increased use of composite resin and the decreased use of amalgam as a dental restorative material, the forensic dental identification of unidentified human remains has become more difficult. Various methods have been used to detect the presence of composite resin restorations including dyes, forensic alternative light sources, quantitative light-induced fluorescence, and ultraviolet lights. Although these methods may be helpful, the expense of the equipment, the electrical requirements, and the need for water to wash the dye from the mouth may make these methods impractical especially in a temporary morgue situation during a mass disaster. The fluorescent properties of composite resins, when exposed to ultraviolet light, are well documented. Standard tube ultraviolet lights have been used to detect the presence of composite resin, but these lights are large and bulky, and the tubes are fragile. The development of ultraviolet light emitting diode flashlights has provided forensic odontologists with a tool that is small, inexpensive, and battery operated. The two forensic dental identification cases described here demonstrate the value of ultraviolet light emitting diode flashlights as an adjunct to a careful clinical and radiographic examination.

  4. Inconsistency in the strength testing of dental resin-based composites among researchers.

    Science.gov (United States)

    Kumar, Naresh

    2013-01-01

    The aims of this paper were to review the current strength testing methods of the dental resin-based composites (RBCs) and to explore the inconsistencies with regard to strength testing among researchers. Data selection/extraction: An outline of the most relevant aspects of RBCs was created, and a subsequent literature search for articles published during last four decades (1970-2010) was conducted using the databases, namely PubMed, Science Direct and ISI Web of Knowledge. The literature review highlighted a lack of consensus among researchers regarding the reliability of ISO recommended three-point flexure strength testing method. Several investigators have used Weibull statistics for the analysis of RBCs strength data, however their applicability might be questioned as many RBCs contain greater resin content and may exhibit sufficient viscous deformation prior to brittle failure. In addition, variability in the selection of cross-head speed and mould material for strength testing was evident which may lead to variation in the strength data and render the interpretation difficult among researchers.

  5. Mathematical modeling of cross-linking monomer elution from resin-based dental composites.

    Science.gov (United States)

    Manojlovic, Dragica; Radisic, Marina; Lausevic, Mila; Zivkovic, Slavoljub; Miletic, Vesna

    2013-01-01

    Elution of potentially toxic substances, including monomers, from resin-based dental composites may affect the biocompatibility of these materials in clinical conditions. In addition to the amounts of eluted monomers, mathematical modeling of elution kinetics reveals composite restorations as potential chronic sources of leachable monomers. The aim of this work was to experimentally quantify elution of main cross-linking monomers from four commercial composites and offer a mathematical model of elution kinetics. Composite samples (n = 7 per group) of Filtek Supreme XT (3M ESPE), Tetric EvoCeram (Ivoclar Vivadent), Admira (Voco), and Filtek Z250 (3M ESPE) were prepared in 2-mm thick Teflon moulds and cured with halogen or light-emitting diode light. Monomer elution in ethanol and water was analyzed using high-performance liquid chromatography up to 28 days postimmersion. The mathematical model was expressed as a sum of two exponential regression functions representing the first-order kinetics law. Elution kinetics in all cases followed the same mathematical model though differences in rate constants as well as the extent of monomer elution were material-, LCU-, medium-dependent. The proposed mechanisms of elution indicate fast elution from surface and subsurface layers and up to 100 times slower monomer extraction from the bulk polymer. Copyright © 2012 Wiley Periodicals, Inc.

  6. Synthesis and study of properties of dental resin composites with different nanosilica particles size.

    Science.gov (United States)

    Karabela, Maria M; Sideridou, Irini D

    2011-08-01

    The aim of this work was the synthesis of light-cured resin nanocomposites using nanosilica particles with different particle size and the study of some physical-mechanical properties of the composites. Various types of silica nanoparticles (Aerosil) with average particle size of 40, 20, 16, 14, and 7 nm, used as filler were silanized with the silane 3-methacryloxypropyl-trimethoxysilane (MPS). The total amount of silane used was kept constant at 10 wt% relative to the filler weight to ensure the complete silanization of nanoparticles. The silanizated silica nanoparticles were identified by FT-IR spectroscopy and thermogravimetric analysis (TGA). Then the silanized nanoparticles (55 wt%) were mixed with a photoactivated Bis-GMA/TEGDMA (50/50 wt/wt) matrix. Degree of conversion of composites was determined by FT-IR analysis. The static flexural strength and flexural modulus were measured using a three-point bending set up. The dynamic thermomechanical properties were determined by dynamic mechanical analyzer (DMA). Sorption, solubility and volumetric change were determined after storage of composites in water or ethanol/water solution 75 vol% for 30 days. The TGA for composites was performed in nitrogen atmosphere from 30 to 700 °C. As the average silica particle size decreases, the percentage amount of MPS attached on the silica surface increases. However, the number of MPS molecules attached on the silica surface area of 1 nm(2) is independent of filler particle size. As the average filler particles size decreases a progressive increase in the degree of conversion of composites and an increase in the amount of sorbed water is observed. The prepared composites containing different amount of silica filler, with different particle size, but with the same amount of silanized silica and organic matrix showed similar flexural strength and flexural modulus, except composite with the lowest filler particle size, which showed lower flexural modulus. Copyright © 2011

  7. Compatibility between dental adhesive systems and dual-polymerizing composite resins.

    Science.gov (United States)

    Michaud, Pierre-Luc; MacKenzie, Alexandra

    2016-10-01

    Information is lacking about incompatibilities between certain types of adhesive systems and dual-polymerizing composite resins, and universal adhesives have yet to be tested with these resins. The purpose of this in vitro study was to investigate the bonding outcome of dual-polymerizing foundation composite resins by using different categories of adhesive solutions and to determine whether incompatibilities were present. One hundred and eighty caries-free, extracted third molar teeth were allocated to 9 groups (n=20), in which 3 different bonding agents (Single Bond Plus [SB]), Scotchbond Multi-purpose [MP], and Scotchbond Universal [SU]) were used to bond 3 different composite resins (CompCore AF [CC], Core Paste XP [CP], and Filtek Supreme Ultra [FS]). After restorations had been fabricated using an Ultradent device, the specimens were stored in water at 37°C for 24 hours. The specimens were tested under shear force at a rate of 0.5 mm/min. The data were analyzed with Kruskal-Wallis tests and post hoc pairwise comparisons (α=.05). All 3 composite resins produced comparable shear bond strengths when used with MP (P=.076). However, when either SB or SU was used, the light-polymerized composite resin (FS) and 1 dual-polymerized foundation composite resin (CC) bonded significantly better than the other dual-polymerized foundation composite resin (CP) (Pcomposite resins can obtain equally good bond strengths as light-polymerizing alternatives. However, not all dual-polymerizing composite resins perform well with all bonding systems; some incompatibilities exist between different products. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  8. The strengthening of resin cemented dental ceramic materials

    OpenAIRE

    Hooi, Paul

    2013-01-01

    The aim of the current investigation was to advance the understanding of the mechanism of resin-strengthening conferred to dental ceramic materials by resin-based composite materials. The investigation is presented as a series of manuscripts. In the first study (Manuscript 3.1), dental porcelain disc-shaped specimens were resin-coated with three resin-based composite materials with different flexural moduli at discrete resin thicknesses. The discs were loaded to failure in a biaxial flexure t...

  9. [Effect of amount of silane coupling agent on flexural strength of dental composite resins reinforced with aluminium borate whisker].

    Science.gov (United States)

    Zhu, Ming-yi; Zhang, Xiu-yin

    2015-06-01

    To evaluate the effect of amount of silane coupling agent on flexural strength of dental composite resins reinforced with aluminium borate whisker (ABW). ABW was surface-treated with 0%, 1%, 2%, 3% and 4% silan coupling agent (γ-MPS), and mixed with resin matrix to synthesize 5 groups of composite resins. After heat-cured at 120 degrees centigrade for 1 h, specimens were tested in three-point flexure to measure strength according to ISO-4049. One specimen was selected randomly from each group and observed under scanning electron microscope (SEM). The data was analyzed with SAS 9.2 software package. The flexural strength (117.93±11.9 Mpa) of the group treated with 2% silane coupling agent was the highest, and significantly different from that of the other 4 groups (α=0.01). The amount of silane coupling agent has impact on the flexural strength of dental composite resins reinforced with whiskers; The flexual strength will be reduced whenever the amount is higher or lower than the threshold. Supported by Research Fund of Science and Technology Committee of Shanghai Municipality (08DZ2271100).

  10. Development of metal-resin composite for dental magnet keepers, Part 2: Optimum 4-META content.

    Science.gov (United States)

    Soma, Hiroko; Miyagawa, Yukio

    2011-01-01

    Six kinds of experimental magnetic resin composites containing SUS447J1 stainless steel particles as filler were prepared. UDMA/MAA resin with an MAA mole fraction of 0.67 was used as the matrix resin. The effects of six levels of 4-META content (2, 4, 6, 8, 10, and 12 mass%) on the setting and flexural properties were studied. The metal filler content in each paste was 90 mass%. Although working time and setting time significantly diminished with the increase of the BPO and DMPT contents, both working time and setting time satisfied the ISO 4049 requirements for all experimental levels. Flexural strength and elastic modules significantly improved with the increase of 4-META content up to 10%. The optimum 4-META content necessary to develop better composite resins for magnetic attachment has been clarified.

  11. Formation of functionalized nanoclusters by solvent evaporation and their effect on the physicochemical properties of dental composite resins.

    Science.gov (United States)

    Rodríguez, Henry A; Giraldo, Luis F; Casanova, Herley

    2015-07-01

    The aim of this work was to study the effect of silica nanoclusters (SiNC), obtained by a solvent evaporation method and functionalized by 3-methacryloxypropyltrimethoxysilane (MPS) and MPS+octyltrimethoxysilane (OTMS) (50/50wt/wt), on the rheological, mechanical and sorption properties of urethane dimethylacrylate (UDMA)/triethylenglycol dimethacrylate (TEGDMA) (80/20wt/wt) resins blend. Silica nanoparticles (SiNP) were silanized with MPS or MPS+OTMS (50/50wt/wt) and incorporated in an UDMA-isopropanol mix to produce functionalized silica nanoclusters after evaporating the isopropanol. The effect of functionalized SiNC on resins rheological properties was determined by large and small deformation tests. Mechanical, thermal, sorption and solubility properties were evaluated for composite materials. The UDMA/TEGDMA (80/20wt/wt) resins blend with added SiNC (ca. 350nm) and functionalized with MPS showed a Newtonian flow behavior associated to their spheroidal shape, whereas the resins blend with nanoclusters silanized with MPS+OTMS (50/50wt/wt) (ca. 400nm) showed a shear-thinning behavior due to nanoclusters irregular shape. Composite materials prepared with bare silica nanoclusters showed lower compressive strength than functionalized silica nanoclusters. MPS functionalized nanoclusters showed better mechanical properties but higher water sorption than functionalized nanoclusters with both silane coupling agents, MPS and OTMS. The solvent evaporation method applied to functionalized nanoparticles showed to be an alternative way to the sinterization method for producing nanoclusters, which improved some dental composite mechanical properties and reduced water sorption. The shape of functionalized silica nanoclusters showed to have influence on the rheological properties of SiNC resin suspensions and the mechanical and sorption properties of light cured composites. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  12. Academy of Dental Materials guidance-Resin composites: Part II-Technique sensitivity (handling, polymerization, dimensional changes).

    Science.gov (United States)

    Ferracane, J L; Hilton, T J; Stansbury, J W; Watts, D C; Silikas, N; Ilie, N; Heintze, S; Cadenaro, M; Hickel, R

    2017-11-01

    The objective of this work, commissioned by the Academy of Dental Materials, was to review and critically appraise test methods to characterize properties related to critical issues for dental resin composites, including technique sensitivity and handling, polymerization, and dimensional stability, in order to provide specific guidance to investigators planning studies of these properties. The properties that relate to each of the main clinical issues identified were ranked in terms of their priority for testing, and the specific test methods within each property were ranked. An attempt was made to focus on the tests and methods likely to be the most useful, applicable, and supported by the literature, and where possible, those showing a correlation with clinical outcomes. Certain methods are only briefly mentioned to be all-inclusive. When a standard test method exists, whether from dentistry or another field, this test has been identified. Specific examples from the literature are included for each test method. The properties for evaluating resin composites were ranked in the priority of measurement as follows: (1) porosity, radiopacity, sensitivity to ambient light, degree of conversion, polymerization kinetics, depth of cure, polymerization shrinkage and rate, polymerization stress, and hygroscopic expansion; (2) stickiness, slump resistance, and viscosity; and (3) thermal expansion. The following guidance is meant to aid the researcher in choosing the most appropriate test methods when planning studies designed to assess certain key properties and characteristics of dental resin composites, specifically technique sensitivity and handling during placement, polymerization, and dimensional stability. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  13. Effect of light-curing units on microleakage under dental composite resins

    Science.gov (United States)

    Queiroz, R. S.; Bandéca, M. C.; Calixto, L. R.; Saade, E. G.; Nadalin, M. R.; Andrade, M. F.; Porto-Neto, S. T.

    2009-09-01

    The aim of this study was to determine the effect of two light-curing units (QTH and LED) on microleakage of Class II composite resin restorations with dentin cavosurface margins. Twenty extracted mandibular first premolars, free of caries and fractures were prepared two vertical “slot” cavities in the occluso-mesial and -destal surfaces (2 mm buccal-lingually, 2 mm proximal-axially and cervical limit in enamel) and divided into 4 equal groups ( n = 8): GI and GII: packable posterior composite light-activated with LED and QTH, respectively; GIII and GIV: micro-hybrid composite resin light-activated with LED and QTH, respectively. The composite resins were applied following the manufacturer’s instructions. After 24 h of water storage specimens were subjected to thermocycling for a total of 500 cycles at 5 and 55°C and the teeth were then sealed with impermeable material. Teeth were immersed in 0.5% Basic fuchsin during 24 h at room temperature, and zero to three levels of penetration score were attributed. The Mann-Whitney and Kruskal-Wallis tests showed significant statistically similar ( P > 0.05) from GI to GII and GIII to GIV, which the GII (2.750) had the highest mean scores and the GIII and GIV (0.875) had lowest mean scores. The use of different light-curing units has no influence on marginal integrity of Class II composite resin restorations and the proprieties of composite resins are important to reduce the microleakage.

  14. Fatigue behavior of dental resin composites: flexural fatigue in vitro versus 6 years in vivo

    NARCIS (Netherlands)

    Garcia-Godoy, F.; Frankenberger, R.; Lohbauer, U.; Feilzer, A.J.; Krämer, N.

    2012-01-01

    Objectives: To evaluate fatigue behavior of direct resin composite restorations (Tetric Ceram vs. Grandio) in vitro and in vivo over an observation period of 6 years. Methods: For the in vitro part, Young's moduli (YM) were calculated and both initial (FS: flexural strength) and fatigue flexural

  15. Review: Resin Composite Filling

    OpenAIRE

    Desmond Ng; Jimmy C. M. Hsiao; Keith C. T. Tong; Harry Kim; Yanjie Mai; Keith H. S. Chan

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin ...

  16. SORPTION AND SOLUBILITY OF LOW-SHRINKAGE RESIN-BASED DENTAL COMPOSITES

    Directory of Open Access Journals (Sweden)

    Sevda Yantcheva

    2016-04-01

    Full Text Available Background: Resin-based composites are well-established restorative materials. However, these materials may absorb significant amounts of water when exposed to aqueous environments. Sorption and solubility are affecting composite restorations by two different mechanisms; the first is the up taking of water producing an increased weight and the second is the dissolution of materials in water, leading to a weight reduction of the final conditioned samples. Objective: To measure the water sorption and solubility of different low-shrinkage resin-based composites. Six materials were selected: Filtek P60, Filtek Ultimate, SonicFill, Filtek Silorane, Kalore and Venus Diamond. Materials and methods: Five disc specimens were prepared of each material and polymerized with diode light-curing unit. Water sorption and solubility of the different materials were were calculated by means of weighting the samples before and after water immersion and desiccation. Data were statistically analyzed using Shapiro-Wilk One Way Analysis of Variance followed by the Holm-Sidak comparison test . Results: There were significant differences (p<=0.001 between materials regarding sorption and solubility. Regarding sorption F. Silorane showed lowest values, followed by SonicFill, without significant difference between them. Statistical significant differences exist between F. Silorane and F.P60, F. Ultimate, Kalore. Significant differences exist between SonicFill and F. Ultimate. F.Silorane (-0.018 and Kalore (-0.010 showed lowest values of solubility but there were marginal difference among all composites investigated. Conclusions: 1.The material with lowest values of sorption and solubility was F.Silorane. 2. The attained sorption and solubility values for composites are influenced by the differences in resin matrix composition and filler contend. 3. Modifications of dimethacrylate matrix did not minimize significantly sorption and solubility of composites. 4. Besides water

  17. Effects of molecular structure of the resins on the volumetric shrinkage and the mechanical strength of dental restorative composites.

    Science.gov (United States)

    Kim, L U; Kim, J W; Kim, C K

    2006-09-01

    To prepare a dental composite that has a low amount of curing shrinkage and excellent mechanical strength, various 2,2-bis[4-(2-hydroxy-3-methacryloyloxy propoxy) phenyl] propane (Bis-GMA) derivatives were synthesized via molecular structure design, and afterward, properties of their mixtures were explored. Bis-GMA derivatives, which were obtained by substituting methyl groups for hydrogen on the phenyl ring in the Bis-GMA, exhibited lower curing shrinkage than Bis-GMA, whereas their viscosities were higher than that of Bis-GMA. Other Bis-GMA derivatives, which contained a glycidyl methacrylate as a molecular end group exhibited reduced curing shrinkage and viscosity. Methoxy substitution for hydroxyl groups on the Bis-GMA derivatives was performed for the further reduction of the viscosity and curing shrinkage. Various resin mixtures, which had the same viscosity as the commercial one, were prepared, and their curing shrinkage was examined. A resin mixture containing 2,2-bis[3,5-dimethyl, 4-(2-methoxy-3-methacryloyloxy propoxy) phenyl] propane] (TMBis-M-GMA) as a base resin and 4-tert-butylphenoxy-2-methyoxypropyl methacrylate (t-BP-M-GMA) as a diluent exhibited the lowest curing shrinkage among them. The composite prepared from this resin mixture also exhibited the lowest curing shrinkage along with enhanced mechanical properties.

  18. Fatigue behavior of dental resin composites: flexural fatigue in vitro versus 6 years in vivo.

    Science.gov (United States)

    Garcia-Godoy, Franklin; Frankenberger, Roland; Lohbauer, Ulrich; Feilzer, Albert J; Krämer, Norbert

    2012-05-01

    To evaluate fatigue behavior of direct resin composite restorations (Tetric Ceram vs. Grandio) in vitro and in vivo over an observation period of 6 years. For the in vitro part, Young's moduli (YM) were calculated and both initial (FS: flexural strength) and fatigue flexural strength (FFL: flexural fatigue limit) were evaluated in a four-point bending setup (n = 15) in distilled water at 37°C. For the in vivo part, 30 patients received 68 direct resin composite restorations of the same materials (Grandio bonded with Solobond M; Tetric Ceram bonded with Syntac). Patients revealed a minimum of two different class II restorations in different quadrants. Epoxy replicas of restored teeth were analyzed under a scanning electron microscope (SEM) at 30× magnification for fatigue characteristics, and 11 selected restorations per group were assessed for marginal fatigue characteristics at 200×. In vitro, YM was 15.7 GPa (Grandio) and 8.7 GPa (Tetric Ceram; p Grandio) versus 101.5 MPa (Tetric Ceram; p > 0.05), and FFL was 63.0 MPa (Grandio) versus 44.3 MPa (Tetric Ceram; p Grandio; p Grandio, clinical outcome for both resin composite materials over 6 years of clinical service was similar. Higher FFLs in vitro seem to be related to less marginal composite fractures in vivo but without any influence on clinical outcome until the 6 years recall. Copyright © 2012 Wiley Periodicals, Inc.

  19. Influence of the light-curing unit, storage time and shade of a dental composite resin on the fluorescence

    Science.gov (United States)

    Queiroz, R. S.; Bandéca, M. C.; Calixto, L. R.; Gaiao, U.; Cuin, A.; Porto-Neto, S. T.

    2010-07-01

    The aim of this study was to determine the influence of three light-curing units, storage times and colors of the dental composite resin on the fluorescence. The specimens (diameter 10.0 ± 0.1 mm, thickness 1.0 ± 0.1 mm) were made using a stainless steel mold. The mold was filled with the microhybrid composite resin and a polyethylene film covered each side of the mold. After this, a glass slide was placed on the top of the mold. To standardize the top surface of the specimens a circular weight (1 kg) with an orifice to pass the light tip of the LCU was placed on the top surface and photo-activated during 40 s. Five specimens were made for each group. The groups were divided into 9 groups following the LCUs (one QTH and two LEDs), storage times (immediately after curing, 24 hours, 7 and 30 days) and colors (shades: A2E, A2D, and TC) of the composite resin. After photo-activation, the specimens were storage in artificial saliva during the storage times proposed to each group at 37°C and 100% humidity. The analysis of variance (ANOVA) and Tukey’s posthoc tests showed no significant difference between storage times (immediately, 24 hours and 30 days) ( P > 0.05). The means of fluorescence had difference significant to color and light-curing unit used to all period of storage ( P 0.05).

  20. Curing kinetics of visible light curing dental resin composites investigated by dielectric analysis (DEA).

    Science.gov (United States)

    Steinhaus, Johannes; Hausnerova, Berenika; Haenel, Thomas; Großgarten, Mandy; Möginger, Bernhard

    2014-03-01

    During the curing process of light curing dental composites the mobility of molecules and molecule segments is reduced leading to a significant increase of the viscosity as well as the ion viscosity. Thus, the kinetics of the curing behavior of 6 different composites was derived from dielectric analysis (DEA) using especially redesigned flat sensors with interdigit comb electrodes allowing for irradiation at the top side and measuring the ion viscosity at the bottom side. As the ion viscosities of dental composites change 1-3 orders of magnitude during the curing process, DEA provides a sensitive approach to evaluate their curing behavior, especially in the phase of undisturbed chain growth. In order to determine quantitative kinetic parameters a kinetic model is presented and examined for the evaluation of the ion viscosity curves. From the obtained results it is seen that DEA might be employed in the investigation of the primary curing process, the quality assurance of ingredients as well as the control of processing stability of the light curing dental composites. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  1. On the design of dental resin-based composites: a micromechanical approach.

    Science.gov (United States)

    Kahler, Bill; Kotousov, Andrei; Swain, Michael V

    2008-01-01

    Adhesive resin-based restorative materials have the potential to considerably strengthen teeth and offer more economically viable alternatives to traditional materials such as gold, amalgam or ceramics. Other advantages are direct and immediate placement and the elimination of the use of mercury. However, polymerization shrinkage during curing of an adhesive restoration and mismatch in mechanical properties can lead to the initiation and development of interfacial defects. These defects could have a detrimental effect on the longevity of the restored tooth. The current study is focused on some design issues of resin-based composites affecting the longevity of the tooth-restoration interface. The theoretical approach is based on self-consistent micromechanical modelling that takes into account the effect of the material properties, volume concentration of the dispersed particle phase as well as the shape of these particles on the overall thermomechanical properties of the composite. Results obtained for resin-based composites reinforced with spherical, disc and short fibre particles highlight the advantages of disc shaped and short fibre particles.

  2. Adherence of Streptococcus Mutans to Microhybrid and Nanohybrid Resin Composites and Dental Amalgam: An In Vitro Study

    Directory of Open Access Journals (Sweden)

    Fariba Motevasselian

    2017-12-01

    Full Text Available Objectives: Streptococcus mutans (S. mutans is a cariogenic microorganism. The restorative materials which harbor a biofilm with high levels of S. mutans can accelerate the occurrence of dental caries. The purpose of this study was to evaluate the influence of different restorative materials on S. mutans colonization in a simple in-vitro biofilm formation model.Materials and Methods: Thirteen discs of each material (nanohybrid resin composite, microhybrid resin composite, and amalgam were prepared, polished, and sterilized in a gamma radiation chamber. The saliva-free specimens were exposed to the S. mutans bacterial suspension (0.5 McFarland and were incubated for 4 hours. Afterwards, the specimens were rinsed and sonicated in normal saline. 10µl of the obtained suspension was cultured in a sterile blood agar medium. After 24 hours, the number of colony forming units (CFU of S. mutans was counted. A sterility test control was considered for each group of materials. The data were analyzed by one-way ANOVA at 5% significance level.Results: The means and standard deviations of the logarithmic values of the colonies on the surfaces of amalgam, microhybrid, and nanohybrid resin composites were equal to 3.76±0.64, 3.91±0.52 and 3.34±0.74, respectively.Conclusions: There were no significant differences between the restorative materials in terms of S. mutans adhesion rate. The evaluated resin composites showed comparable numbers of CFUs, which could imply the importance of the polishing procedures.

  3. Review: Resin Composite Filling

    Directory of Open Access Journals (Sweden)

    Desmond Ng

    2010-02-01

    Full Text Available The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  4. Review: Resin Composite Filling

    Science.gov (United States)

    Chan, Keith H. S.; Mai, Yanjie; Kim, Harry; Tong, Keith C. T.; Ng, Desmond; Hsiao, Jimmy C. M.

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  5. Physical properties of current dental nanohybrid and nanofill light-cured resin composites.

    Science.gov (United States)

    Sideridou, Irini D; Karabela, Maria M; Vouvoudi, Evangelia Ch

    2011-06-01

    The purpose of this work was the detailed study of sorption characteristics of water or artificial saliva, the determination of flexural strength and the flexural modulus, and the study of the thermal stability of some current commercial dental light-cured nanocomposites containing nano-sized filler particles. Three nanohydrid dental composites (Tetric EvoCeram (TEC), Grandio (GR) and Protofill-nano (PR)) and two nanofill composites (Filtek Supreme Body (FSB) and the Filtek Supreme Translucent (FST)) were used in this work. The volumetric shrinkage due to polymerization was first determined. Also the sorption, solubility and volumetric increase were measured after storage of composites in water or artificial saliva for 30 days. The flexural strength and flexural modulus were measured using a three-point bending set-up according to the ISO-4049 specification, after immersion of samples in water or artificial saliva for 1 day or 30 days. Thermal analysis technique TGA method was used to investigate the thermal stability of composites. GR and TEC composites showed statistically no difference in volumetric shrinkage (%) which is lower than the other composites, which follow the order PRGrandio had the lowest polymer matrix content, consisting mainly of Bis-GMA. It showed the lowest polymerization shrinkage and water sorption and the highest flexural strength and flexural modulus after immersion in water or artificial saliva for 30 days. The water and artificial saliva generally showed the same effect on physical properties of the studied composites. Thermogravimetric analysis gave good information about the structure and the amount of organic polymer matrix of composites. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  6. R-curve behavior and micromechanisms of fracture in resin based dental restorative composites.

    Science.gov (United States)

    Shah, M B; Ferracane, J L; Kruzic, J J

    2009-10-01

    The fracture properties and micromechanisms of fracture for two commercial dental composites, one microhybrid (FiltekZ250) and one nanofill (FiltekSupreme Plus), were studied by measuring fracture resistance curves (R-curves) using pre-cracked compact-tension specimens and by conducting both unnotched and double notched four point beam bending experiments. Four point bending experiments showed about 20% higher mean flexural strength of the microhybrid composite compared to the nanofill. Rising fracture resistance was observed over approximately 1 mm of crack extension for both composites, and higher overall fracture resistance was observed for the microhybrid composite. Such fracture behavior was attributed to crack deflection and crack bridging toughening mechanisms that developed with crack extension, causing the toughness to increase. Despite the lower strength and toughness of the present nanofill composite, based on micromechanics observations, large nanoparticle clusters appear to be as effective at deflecting cracks and imparting toughening as solid particles. Thus, with further microstructural refinement, it should be possible to achieve a superior combination of aesthetic and mechanical performance using the nanocluster approach for dental composites.

  7. General dental practitioners' knowledge of polymerisation of resin-based composite restorations and light curing unit technology.

    Science.gov (United States)

    Santini, A; Turner, S

    2011-09-23

    Clinical successful use of resin-based composite restorations (RBCs) depends on knowledge of material and light curing unit (LCU) related factors. The purpose of this study was to evaluate general dental practitioners' knowledge of polymerisation of RBCs and LCU technology. Members of the Active Research Group of the Faculty of General Dental Practice (UK) in England, Scotland and Wales engaged in primary dental care were sent a letter introducing the study and asking for their cooperation, followed by an email containing a link to the online survey questionnaire, hosted on Surveymonkey.com. The questionnaire enquired about current LCUs, and asked a series of questions on material science. Sixty-six percent of the 274 members contacted responded. Fifty-seven percent used LED units, 25% quartz tungsten halogen (QTH), and 1% plasma arc (missing: 17%). Thirty percent reported having access to a radiometer. Appropriate responses regarding the degree of conversion of composite and adhesive materials were given by 32% and 23% respectively, and 22% agreed that LED and QTH LCUs had comparable efficiency in polymerising composites. Thirty-three percent were aware that RBCs eluted substances that may have adverse local or systemic consequences. Fifty-eight percent stated that if polymerisation of RBC is slowed down, polymerisation stress will be lower, and 43% said that polymerisation shrinkage will be reduced if the degree of conversion is reduced. Knowledge (measured by appropriate responses to these questions) was not related to years since qualification (r=-0.05, n=168, p=0.53). The study suggests that dentists' knowledge of curing RBC restorations and LCUs is poor. This indicates that there is a need for training and guidance in this aspect of primary dental care.

  8. Influence of retainer design on two-unit cantilever resin-bonded glass fiber reinforced composite fixed dental prostheses: An in vitro and finite element analysis study

    NARCIS (Netherlands)

    Keulemans, F.; de Jager, N.; Kleverlaan, C.J.; Feilzer, A.J.

    2008-01-01

    Purpose: The aim of this study was to evaluate in vitro the influence of retainer design on the strenght of two-unit cantilever resin-bonded glass fiber-reinforced composite (FRC) fixed dental prostheses (FDP). Conclusion: A dual-wing retainer is the optimal design for replacement of a single

  9. Simultaneous determination of components released from dental composite resins in human saliva by liquid chromatography/multiple-stage ion trap mass spectrometry.

    Science.gov (United States)

    Hsu, Wei-Yi; Wang, Ven-Shing; Lai, Chien-Chen; Tsai, Fuu-Jen

    2012-02-01

    Dental composite resins are widely used for fixing teeth; however, the monomers used in dental composite resins have been found to be cytotoxic and genotoxic, namely triethylene glycol dimethacrylate (TEGDMA), urethane dimethacrylate (UDMA), and bisphenol A glycol dimethacrylate (Bis-GMA). In this study, we incubated dental composite resins with human saliva for demonstrating the released monomers and biodegradation products. A simple saliva sample dilution method without purification or derivatization was used for quantification. We found that liquid chromatography coupled with multiple-stage ion trap mass spectrometry (LC-MS(n) ) operated in selected reaction monitoring (SRM) mode was able to separate the three monomers within 10 min. The calibration curves were linear (R² >0.996) over a wide range for each monomer in saliva: TEGDMA, 5-500 ppb; UDMA, 5-100 ppb, and Bis-GMA, 5-700 ppb. Furthermore, several biodegradation products were discovered with data-dependent MS/MS scan techniques. Although TEGMA degradation products have previously been reported, we identified two previously unknown UDMA degradation products. The LC-MS/MS method developed in this study was able to successfully quantify monomers and their principal biodegradation products from dental composite resins in human saliva. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. A novel zirconia fibre-reinforced resin composite for dental use.

    Science.gov (United States)

    Wang, Ting; Tsoi, James Kit-Hon; Matinlinna, Jukka Pekka

    2016-01-01

    The purpose of this study was to evaluate and compare some biomechanical properties such as fracture toughness, Vickers hardness and compressive strength of an experimental fibre-reinforced composite (FRC) filled with various percentages (0 wt%, 1 wt%, 3 wt%, and 5 wt%) of zirconia (ZrO2) fibres. A resin matrix (78.4 wt% bis-GMA, 19.6 wt% MMA, 1-wt% CEMA and 1 wt% CQ) with different percentages of silanized zirconia fibres (0%, 1%, 3%, and 5% by weight of the resin matrix) was prepared. Silanization was carried out using an experimental silane blend (0.5 vol% bis-1,2-(triethoxysilyl)ethane+1.0 vol% 3-acryloxypropyltrimethoxysilane in ethanol, at pH 4.0). Each group of specimens was stored in two conditions - either at room temperature for one day or water storage at 37 °C for 7 days. They were randomly divided into study groups according to the test method. For fracture toughness, a notchless triangular prism (NTP) test (n=6) was undertaken. Hardness values (n=6) were measured by using a Vickers hardness testing machine and compressive strength (n=6) was tested. Scanning electron microscopy (SEM) images were taken at the fracture sites after fracture toughness test. The data were analysed by 1-way ANOVA (analysis of variance) and Bonferroni post-hoc tests (α=0.05). The ANOVA test revealed that the experimental FRCs with 1 wt% and 3 wt% zirconia fibres showed statistically significant differences in Vickers hardness at dry condition and NTP fracture toughness after 7-day water storage, respectively. However, compressive strength of experimental groups exhibited no significant difference (p>0.05). Silanized zirconia fibres reinforcement in resin is a novel FRC which have shown promising biomechanical properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Surface Hardness of Dental Composite Resin Restorations in Response to Preventive Agents.

    Science.gov (United States)

    Al-Samadani, Khalid H

    2016-12-01

    To assess the impact of using preventive mouthwash agents on the surface hardness of various resins composites. Hundred specimens were prepared from five types of composite resin material in a Teflon mold. Five specimens from each type of restorative materials (Herculite XRV Ultra, Estelite Σ Quick, Z Hermack, Versa Comp Sultan, and Empress Direct IPS) were evaluated posttreatment with immersion in four types of preventive mouthwashes gels and rinses - group 1: Flocare gel (0.4% stannous fluoride), group 2: Pascal gel (topical APF fluoride), group 3: Pro-relief mouthwash (Na fluoride), and group 4: Plax Soin mouthwash (Na fluoride) - at 37°C in a dark glass container at 24, 48, and 72 hours. Surface hardness measurement was made for each tested material. Statistically, we analyzed the mean values with one-way analysis of variance (ANOVA) and Tukey's test, with significance level of p surface hardness with the time elapsed (24, 48, and 72 hours) postimmersion in the preventive mouthwashes and gels except the Herculite XRV Ultra and Versa Comp Sultan materials. Flocare gel group showed increase in the surface hardness after 48 hours of immersion than the other periods and in Estelite Σ Quick after 72 hours. There was significant differences in all materials tested with the immersion in the preventive mouthwashes and gels, such as Flocare gel (0.4% stannous fluoride), Pro-relief mouthwash (Na fluoride), and Plax Soin mouthwash (Na fluoride) except Pascal gel (topical APF fluoride) (p > 0.05), at time intervals mentioned earlier (p surface hardness with the time elapse of immersion for all materials except the Flocare gel group, which contains 0.4% stannous fluoride as a preventive ingredient increases the surface hardness after 48 h for Herculite XRV Ultra and Versa Comp Sultan and Estelite Σ Quick after 72 hours. The preventive agents in the form of mouthwash and gel are used to prevent oral diseases that affect the surface hardness of composite resin, and this

  12. Longevity of posterior resin composite restorations in permanent teeth in Public Dental Health Service: a prospective 8 years follow up.

    Science.gov (United States)

    Pallesen, Ulla; van Dijken, Jan W V; Halken, Jette; Hallonsten, Anna-Lena; Höigaard, Ruth

    2013-04-01

    To investigate in a prospective follow up the longevity of posterior resin composites (RC) placed in permanent teeth of children and adolescents attending Public Dental Health Service. All posterior RC placed, in the PDHS clinics in the cities of Copenhagen and Frederiksberg in Denmark between November 1998 and December 2002, in permanent teeth of children and adolescents up to 18 years, were evaluated in an up to 8 years follow up. The endpoint of each restoration was defined, when repair or replacement was performed. Survival analyses were performed between subgroups with Kaplan-Meier analysis. The individual contribution of different cofactors to predict the outcome was performed with Cox regression analysis. Totally 2881 children with a mean age of 13.7 years (5-18) received 4355 RC restorations placed by 115 dentists. Eighty percent were placed in molars and 49% were Class I. Two percent of restorations with base material and 1% of the restorations without base material showed postoperative sensitivity (n.s.). Replacements were made in 406 and repairs in 125 restorations. Kaplan-Meier analysis showed a cumulative survival at 8 years of 84.3%, resulting in an annual failure rate of 2%. Lower patient age, more than one restoration per patient, placement of a base material and placement of RC: in molars, in cavities with high number of surfaces, in lower jaw teeth, showed all significant higher failure rates. Five variables had significant importance for the end point, replacement/repair of the resin composite restorations: age of patient, age of operator, jaw, tooth type and cavity size. Posterior RC restorations placed in children and adolescents in Public Dental Health clinics showed an acceptable durability with annual failure rates comparable with those of randomized controlled RC studies in adults. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. The antifungal effects and mechanical properties of silver bromide/cationic polymer nano-composite-modified Poly-methyl methacrylate-based dental resin.

    Science.gov (United States)

    Zhang, Yu; Chen, Yin-Yan; Huang, Li; Chai, Zhi-Guo; Shen, Li-Juan; Xiao, Yu-Hong

    2017-05-08

    Poly-methyl methacrylate (PMMA)-based dental resins with strong and long-lasting antifungal properties are critical for the prevention of denture stomatitis. This study evaluated the antifungal effects on Candida albicans ATCC90028, the cytotoxicity toward human dental pulp cells (HDPCs), and the mechanical properties of a silver bromide/cationic polymer nano-composite (AgBr/NPVP)-modified PMMA-based dental resin. AgBr/NPVP was added to the PMMA resin at 0.1, 0.2, and 0.3 wt%, and PMMA resin without AgBr/NPVP served as the control. Fungal growth was inhibited on the AgBr/NPVP-modified PMMA resin compared to the control (P  0.05) between the experimental and control groups. These data indicate that the incorporation of AgBr/NPVP conferred strong and long-lasting antifungal effects against Candida albicans to the PMMA resin, and it has low toxicity toward HDPCs, and its mechanical properties were not significantly affected.

  14. A prospective 8-year follow-up of posterior resin composite restorations in permanent teeth of children and adolescents in Public Dental Health Service: reasons for replacement

    DEFF Research Database (Denmark)

    Pallesen, Ulla; van Dijken, Jan W.V.; Halken, Jette

    2014-01-01

    Objectives: the aim of the study was to investigate reasons for replacement and repair of posterior resin composite (RC) restorations placed in permanent teeth of children and adolescents attending Public Dental Health Service in Denmark. Material and method: all posterior RC placed consecutively...... in general practice showed a good durability with annual failure rates of 2 %. The main reason for failure was secondary caries followed by post-operative sensitivity and resin composite fracture. A high proportion of replaced/repaired RC restorations were caused by primary caries in a non-filled surface...

  15. Effect of food simulating liquids on release of monomers from two dental resin composites

    Directory of Open Access Journals (Sweden)

    Ghavam M

    2010-06-01

    Full Text Available "nBackground and Aims: The elution of residual monomers from cured dental composites to oral cavity has a harmful effect on human health and can affect their clinical durability. The purpose of this study was to evaluate the amount of eluted monomers (Bis-GMA, TEGDMA, UDMA from two types of composites (Gradia and P60 after exposure to food simulating liquids such as ethanol (25, 50, 75 % and heptane 50 % for 24 hours and 7 days. "nMaterials and Methods: Forty specimens of each composite were prepared. Equal numbers of each composite were immersed in tubes containing 2cc volumes of 25, 50, 75 % ethanole and 50 % heptane. The amount of eluted monomers in standard condition such as Bis-GMA, TEGDMA and UDMA was measured by GC/MS (Gas Chromatography/Mass Spectroscopy and results were statistically analysed by three way and one way ANOVA. P<0.05 was considered as the level of significancy. "nResults: The results showed that Gradia released more TEGDMA than P60. In assessing the effect of environment, the result showed that ethanol caused releasing monomers more than heptane and the concentration rate of 75 % ethanole resulted in most releasing of monomers. In assessing the effect of time, the observation showed that more monomers were released 7 days compared to 24 hours. Bis-GMA and UDMA were not detected in any solutions in these conditions. "nConclusion: Ethanole caused more release of monomers than heptane and 75 % ethanole released the most amount of monomers. Gradia released more amount of TEGDMA than P60.

  16. In vitro toothbrushing abrasion of dental resin composites: packable, microhybrid, nanohybrid and microfilled materials

    Directory of Open Access Journals (Sweden)

    Rafael Ratto de Moraes

    2008-06-01

    Full Text Available This study evaluated weight loss and surface roughening after toothbrushing of different resin composites: one packable (Solitaire 2, Heraeus Kulzer, one microhybrid (Charisma, Heraeus Kulzer, one nanohybrid (Simile, Pentron and one microfilled (Durafill VS, Heraeus Kulzer. Cylindrical specimens (n = 20 were prepared. Half of the samples were submitted to 60,000 strokes, at 4 Hz, with a dentifrice-water slurry. Control samples (n = 10 remained stored at 37°C. Pre- and post-abrasion parameters for weight (mg and surface roughness (Ra, µm were determined on an analytical balance and a surface profilometer. Data were separately submitted to Repeated Measures ANOVA and Tukey's test (a = 0.05. Percentages of weight loss were analyzed by ANOVA and Tukey's test (a = 0.05. The relationship between both evaluations was assessed by Pearson's test (a = 0.05. The means (% for weight loss (standard deviation were 0.65(0.2, 0.93(0.2, 1.25(0.6 and 1.25(0.4 for Simile, Durafill, Charisma and Solitaire, respectively. Baseline roughness means ranged from 0.065(0.01, 0.071(0.01, 0.066(0.02 and 0.074(0.01 for Simile, Durafill, Charisma and Solitaire, respectively, to 0.105(0.04, 0.117(0.03, 0.161(0.03 and 0.214(0.07 after testing. The composites with larger fillers presented higher weight loss and roughening than the finer materials (p < 0.05. For both evaluations, control specimens showed no significant alteration. No significant relationship between loss of weight and roughness alteration was detected (r = 0.322, p = 0.429.

  17. Protective effects of resin sealant and flowable composite coatings against erosive and abrasive wear of dental hard tissues.

    Science.gov (United States)

    Zhao, Xiaoyi; Pan, Jie; Malmstrom, Hans S; Ren, Yan-Fang

    2016-06-01

    To test the effectiveness of sealant and flowable composite coating on eroded enamel, dentin and cementum under erosive/abrasive challenges in vitro. A total of 108 tissue sections (36 each for enamel, dentin and cementum) from third molars were assigned to three groups: Seal & Protect sealant (S&P), Tetric EvoFlow composite (TEF) and control. Erosive/abrasive lesions were created on each specimen by citric acid and brushing with toothpaste. S&P and TEF were applied to the lesions and subjected to erosive/abrasive cycling included 24 cycles of immersion in citric acid (pH 3.6) for 60min, followed by remineralization for 120min and brushing with toothpastes for 600 strokes at 150g. Erosive wear of materials or dental tissues were measured with 3D scanning microscopy and data were analyzed using ANOVA. Treatments with S&P and TEF created a protective material coating of 42.7±17.8μm and 150.8±9.9μm in thickness, respectively. After 24 cycles of erosive/abrasive challenges, tissue losses were -346.9±37.3μm for enamel, -166.5±26.3μm for dentin and -164.7±18.2μm for cementum in untreated controls, as compared to material losses of -24.4±3.3μm for S&P, and -10.8±4.4μm for TEF, respectively. Both S&P and TEF were effective in protecting enamel, dentin and cementum against erosive tooth wear (pwear than TEF (pabrasive challenges. A thin coating of flowable composite resin 150μm in thickness may provide long-term protection against erosive/abrasive tooth wear. Resin sealant may provide adequate protection for dental hard tissues in short-term and may require repeated applications if long-term protection is desired. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Effect of food/oral-simulating liquids on dynamic mechanical thermal properties of dental nanohybrid light-cured resin composites.

    Science.gov (United States)

    Vouvoudi, Evangelia C; Sideridou, Irini D

    2013-08-01

    The purpose of this work was the study of the effect of food/oral simulating liquids on the dynamic mechanical thermal properties (viscoelastic properties) of current commercial dental light-cured resin composites characterized as nanohybrids. These nanohybrids were Grandio, Protofill-nano and Tetric EvoCeram. The properties were determined under dry conditions (1h at 37°C after light-curing) and also after storage in dry air, distilled water, artificial saliva SAGF(®) or ethanol/water solution (75 vol%) at 37°C for up 1, 7, 30 or 90 days. Dynamic mechanical thermal analysis tests were performed on a Diamond Dynamic Mechanical Analyzer in bending mode. A frequency of 1Hz and a temperature range of 25-185°C were applied, while the heating rate of 2°C/min was selected to cover mouth temperature and the materials' likely Tg. Storage modulus, loss modulus and tangent delta were plotted against temperature over this period. The Tg of composites was obtained as the temperature indicated by tanδ peak. Moreover, the maximum height of tanδ peak, the width at the half of tanδ maximum and a parameter known as "ζ" parameter were determined. All composites analyzed 1h after light-curing and 1 day in air or in food/oral simulating liquids showed two Tg. All composites stored for 7, 30 or 90 days in any medium showed unique Tg value. Also among the various properties studied the most sensible in the structural changes of composites seems to be the Tg. Storage of composites in dry air at 37°C which is very close to their Tg (40°C) for 1 or 7 days caused post curing reactions, while storage for 30 or 90 days has no further effect on composites. Storage in water or artificial saliva 37°C for 1 or 7 days caused post curing reactions, while storage for 30 or 90 days seems to cause plasticization effect affecting some parameters analogously. Storage in ethanol/water solution (75vol%) 37°C for 1 or 7 days caused also post curing reactions, while storage for 30 or 90 days

  19. Dielectric analysis of depth dependent curing behavior of dental resin composites.

    Science.gov (United States)

    Steinhaus, Johannes; Moeginger, Bernhard; Grossgarten, Mandy; Rosentritt, Martin; Hausnerova, Berenika

    2014-06-01

    The aim of this study is to investigate depth dependent changes of polymerization process and kinetics of visible light-curing (VLC) dental composites in real-time. The measured quantity - "ion viscosity" determined by dielectric analysis (DEA) - provides the depth dependent reaction rate which is correlated to the light intensity available in the corresponding depths derived from light transmission measurements. The ion viscosity curves of two composites (VOCO Arabesk Top and Grandio) were determined during irradiation of 40s with a light-curing unit (LCU) in specimen depths of 0.5/0.75/1.0/1.25/1.5/1.75 and 2.0mm using a dielectric cure analyzer (NETZSCH DEA 231 with Mini IDEX sensors). The thickness dependent light transmission was measured by irradiation composite specimens of various thicknesses on top of a radiometer setup. The shape of the ion viscosity curves depends strongly on the specimen thickness above the sensor. All curves exhibit a range of linear time dependency of the ion viscosity after a certain initiation time. The determined initiation times, the slopes of the linear part of the curves, and the ion viscosities at the end of the irradiation differ significantly with depth within the specimen. The slopes of the ion viscosity curves as well as the light intensity values decrease with depth and fit to the Lambert-Beer law. The corresponding attenuation coefficients are determined for Arabesk Top OA2 to 1.39mm(-1) and 1.48mm(-1), respectively, and for Grandio OA2 with 1.17 and 1.39mm(-1), respectively. For thicknesses exceeding 1.5mm a change in polymerization behavior is observed as the ion viscosity increases subsequent to the linear range indicating some kind of reaction acceleration. The two VLC composites and different specimen thicknesses discriminate significantly in their ion viscosity evolution allowing for a precise characterization of the curing process even with respect to the polymerization mechanism. Copyright © 2014. Published by

  20. Effect of Colgate Sensitive Pro-Relief paste on the strength of adhesion of composite resin in dental pieces

    International Nuclear Information System (INIS)

    Davila Rodriguez, Amanda; Sas Rosero, Cristina de

    2013-01-01

    The effect of the toothpaste Colgate Sensitive Pro-Relief on the strength of adhesion was analyzed, through in vitro studies, in dental pieces that have been previously treated with a protocol that simulates dental hypersensitivity. Several dental pieces were taken as study samples and divided into groups. The Colgate Sensitive Pro-Relief TM desensitizing paste was applied to the non-crown surfaces of the teeth, with the exception of the negative control group which remained without the application. Positive control protocols, prophylaxis with the use of fluorinated prophylactic paste, 400 grit sandpaper, phosphoric acid and negative control were applied. Subsequently, a Brilliant NG TM dentin photocurable resin crown was constructed for the groups to which the indicated protocols were applied. The greatest strength of adhesion was presented by the group Prophylaxis. It is assumed that a second application of orthophosphoric acid is able to de-blot even more the dental tubules and with this improve the adhesion. An improvement in the adhesion of resin on the tooth surface is provided when performing a dental prophylaxis using prophylactic paste and a rubber cup, before restoring a tooth. Sandpaper 400 prevents an improvement in the adhesion of resins. The results with the negative control group were unexpected and may be due to errors in the treatment process [es

  1. COMPARATIVE STUDY OF THE SHEAR BOND STRENGTH OF COMPOSITE RESIN TO DENTAL ENAMEL CONDITIONED WITH PHOSPHORIC ACID OR Nd: YAG LASER

    Directory of Open Access Journals (Sweden)

    EDUARDO Carlos de Paula

    1997-01-01

    Full Text Available This study has been focused on a comparison between the shear bond strength of a composite resin attached to dental enamel surface, after a 35% phosphoric acid etching and after a Nd:YAG laser irradiation with 165.8 J/cm2 of energy density per pulse. After etching and attaching resin to these surfaces, the specimens were thermocycled and then underwent the shearing bond strength tests at a speed of 5 mm/min. The results achieved, after statistical analysis with Student's t-test, showed that the adhesion was significantly greater in the 35% phosphoric acid treated group than in the group treated with the Nd:YAG laser, thus demonstrating the need for developing new studies to reach the ideal parameters for an effective enamel surface conditioning as well as specific adhesives and composite resins when Nd:YAG laser is used

  2. Evaluation of microleakage of class II dental composite resin restorations cured with LED or QTH dental curing light; Blind, Cluster Randomized, In vitro cross sectional study.

    Science.gov (United States)

    Zakavi, Faramarz; Golpasand Hagh, Leila; Sadeghian, Soheila; Freckelton, Virginia; Daraeighadikolaei, Arash; Ghanatir, Elham; Zarnaghash, Najmeh

    2014-07-03

    The aim of this study is to compare the microleakage of Class II dental composite resin restorations which have been cured by three different LED (light emitting diode) light curing modes compared to control samples cured by QTH (quartz tungsten halogen) light curing units (LCUs), to determine the most effective light curing unit and mode of curing. In this experimental study, class II cavities were prepared on 100 sound human premolars which have been extracted for orthodontic treatment. The teeth were randomly divided into four groups; three experimental and one control group of 25 teeth each. Experimental groups were cured by either conventional, pulse-delay, or ramped curing modes of LED. The control group was cured for 20 seconds by QTH. The restorations were thermocycled (1000 times, between 5 and 55°C, for 5 seconds dwell time), dyed, sectioned mesio-distally and viewed under stereo-microscope (40×) magnification. Teeth were then scored on a 0 to 4 scale based on the amount of microleakage. The data were analyzed by Chi-square test.No significant difference was demonstrated between the different LCUs (light curing units), or modes of curing, at the enamel side (p > 0.05). At the dentin side, all modes of LED curing could significantly reduce microleakage (p curing improves marginal integrity and seal. High intense curing endangers those aims. Comparison between the three LED mode cured composite resin restorations and QTH curing showed LED curing in all modes is more effective than QTH for reducing microleakage. Both LED and QTH almost completely eliminate the microleakage on the enamel side, however none of them absolutely eliminated microleakage on the dentin side.

  3. Measurement of J-integral in CAD/CAM dental ceramics and composite resin by digital image correlation.

    Science.gov (United States)

    Jiang, Yanxia; Akkus, Anna; Roperto, Renato; Akkus, Ozan; Li, Bo; Lang, Lisa; Teich, Sorin

    2016-09-01

    Ceramic and composite resin blocks for CAD/CAM machining of dental restorations are becoming more common. The sample sizes affordable by these blocks are smaller than ideal for stress intensity factor (SIF) based tests. The J-integral measurement calls for full field strain measurement, making it challenging to conduct. Accordingly, the J-integral values of dental restoration materials used in CAD/CAM restorations have not been reported to date. Digital image correlation (DIC) provides full field strain maps, making it possible to calculate the J-integral value. The aim of this study was to measure the J-integral value for CAD/CAM restorative materials. Four types of materials (sintered IPS E-MAX CAD, non-sintered IPS E-MAX CAD, Vita Mark II and Paradigm MZ100) were used to prepare beam samples for three-point bending tests. J-integrals were calculated for different integral path size and locations with respect to the crack tip. J-integral at path 1 for each material was 1.26±0.31×10(-4)MPam for MZ 100, 0.59±0.28×10(-4)MPam for sintered E-MAX, 0.19±0.07×10(-4)MPam for VM II, and 0.21±0.05×10(-4)MPam for non-sintered E-MAX. There were no significant differences between different integral path size, except for the non-sintered E-MAX group. J-integral paths of non-sintered E-MAX located within 42% of the height of the sample provided consistent values whereas outside this range resulted in lower J-integral values. Moreover, no significant difference was found among different integral path locations. The critical SIF was calculated from J-integral (KJ) along with geometry derived SIF values (KI). KI values were comparable with KJ and geometry based SIF values obtained from literature. Therefore, DIC derived J-integral is a reliable way to assess the fracture toughness of small sized specimens for dental CAD/CAM restorative materials; however, with caution applied to the selection of J-integral path. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Clinical study of indirect composite resin inlays in posterior stress-bearing cavities placed by dental students: results after 4 years.

    Science.gov (United States)

    Huth, Karin Christine; Chen, Hong Yan; Mehl, Albert; Hickel, Reinhard; Manhart, Juergen

    2011-07-01

    This longitudinal randomized controlled clinical trial evaluated the longevity of composite resin inlays in single- or multi-surface cavities up to 4 years. 21 dental students placed 75 Artglass and 80 Charisma composite resin inlays in class I and II cavities in posterior teeth (89 adult patients) luted with dual-curing resin cements. Clinical evaluation was performed up to 4 years using modified USPHS criteria. 87.2% of Artglass and 76.6% of Charisma inlays were assessed to be clinically excellent or acceptable. Up to the 4-year recall 5 Artglass and 11 Charisma inlays failed mainly because of postoperative symptoms, bulk fracture, and loss of marginal integrity. No significant differences between both composite resin materials could be detected at 4 years for all clinical criteria (Mann-Whitney U-test, p>0.05). The comparison of restoration performance with time yielded a significant increase in marginal discolouration and postoperative symptoms (pinlay systems. However, the changes were mainly effects of scoring shifts from alfa to bravo. Small inlays compared to large inlays and premolar restorations compared to molar restorations showed significant better outcome for some of the tested clinical parameters for the Artglass inlays (pinlays no such influences were revealed. Clinical assessment of Artglass and Charisma composite resin inlays exhibited an annual failure rate of 3.2% and 5.9% that is within the range of published data. Within the limitations of this study indirect composite inlays are a competitive restorative procedure in stress-bearing preparations. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Influence of retainer design on two-unit cantilever resin-bonded glass fiber reinforced composite fixed dental prostheses: an in vitro and finite element analysis study.

    Science.gov (United States)

    Keulemans, Filip; De Jager, Niek; Kleverlaan, Cornelis J; Feilzer, Albert J

    2008-10-01

    The aim of this study was to evaluate in vitro the influence of retainer design on the strength of two-unit cantilever resin-bonded glass fiber-reinforced composite (FRC) fixed dental prostheses (FDP). Four retainer designs were tested: a proximal box, a step-box, a dual wing, and a step-box-wing. Of each design on 8 human mandibular molars, FRC-FDPs of a premolar size were produced. The FRC framework was made of resin impregnated unidirectional glass fibers (Estenia C&B EG Fiber, Kuraray) and veneered with hybrid resin composite (Estenia C&B, Kuraray). Panavia F 2.0 (Kuraray) was used as resin luting cement. FRC-FDPs were loaded to failure in a universal testing machine. One-way ANOVA and Tukey's post-hoc test were used to evaluate the data. The four designs were analyzed with finite element analysis (FEA) to reveal the stress distribution within the tooth/restoration complex. Significantly lower fracture strengths were observed with inlay-retained FDPs (proximal box: 300 +/- 65 N; step-box: 309 +/- 37 N) compared to wing-retained FDPs (p optimal design for replacement of a single premolar by means of a two-unit cantilever FRC-FDPs.

  6. Clinical study of indirect composite resin inlays in posterior stress-bearing preparations placed by dental students: results after 6 months and 1, 2, and 3 years.

    Science.gov (United States)

    Manhart, Juergen; Chen, Hong-Yan; Mehl, Albert; Hickel, Reinhard

    2010-05-01

    This longitudinal randomized controlled clinical trial evaluated composite resin inlays for clinical acceptability in single- or multisurface preparations and provides a survey of the results up to 3 years. Twenty-one dental students placed 75 Artglass (Heraeus Kulzer) and 80 Charisma (Heraeus Kulzer) composite resin inlays in Class 1 and 2 preparations in posterior teeth (89 adults). Clinical evaluation was performed at baseline and up to 3 years by two other dentists using modified USPHS criteria. A total of 89.8% of Artglass and 84.1% of Charisma inlays were assessed as clinically excellent or acceptable with predominating Alfa scores. Up to the 3-year recall, five Artglass and 10 Charisma inlays failed mainly because of postoperative symptoms, bulk fracture, and loss of marginal integrity. No significant differences between composite resin materials could be detected at 3 years for all clinical criteria (P > .05). The comparison of restoration performance with time within both groups yielded a significant increase in marginal discoloration (P inlay systems. However, both changes were mainly effects of scoring shifts from Alfa to Bravo. No significant differences (P > .05) were recorded comparing premolars and molars. Small inlays showed significantly better outcome for some of the tested clinical parameters (P inlays exhibited an annual failure rate of 3.4% and 5.3% that is within the range of published data. Indirect composite inlays are a competitive restorative procedure in stress-bearing preparations.

  7. EFFECT OF LIGHT CURING UNIT CHARACTERISTICS ON LIGHT INTENSITY OUTPUT, DEPTH OF CURE AND SURFACE MICRO-HARDNESS OF DENTAL RESIN COMPOSITE.

    Science.gov (United States)

    Kassim, B A; Kisumbi, B K; Lesan, W R; Gathece, L W

    2013-09-01

    Modern dental composite restorations are wholly dependent on the use of Visible Light Curing devices. The characteristics of these devices may influence the quality of composite resin restorations. To determine the characteristics of light curing units (LCUs) in dental clinics in Nairobi and their effect on light intensity output, depth of cure (DOC) and surface micro-hardness (SMH) of dental resin composite. Laboratory based, cross-sectional analytical study. Public and private dental clinics in Nairobi, Kenya. Eighty three LCUs which were in use in private and public dental health facilities in Nairobi, Kenya and resin composite specimens. Of the 83 LCUs studied, 43 (51.8%) were Light Emitting Diodes (LEDs) and 39(47.0%) were Quartz-Tungsten-Halogen (QTH) and 1 (1.2%) was Plasma Arc Curing (PAC) light. Mean light intensity for QTH and LED lights was 526.59 mW/cm2 and 493.67 mW/cm2 respectively (p=0.574), while the mean DOC for QTH lights was 1.71 mm and LED was 1.67 mm (p=0.690). Mean Vickers Hardness Number (VHN) for LED was 57.44 and for QTH was 44.14 (p=0.713). Mean light intensity for LCUs units > 5 years old (p=0.024). The mean DOC for the two age groups was 1.74 mm and 1.57 mm respectively (p=0.073). For SMH, the 5 years age groups gave a mean VHN of 58.81 and 51.46 respectively (p=0.1). On maintenance history, the frequency of routine inspection, duration since the last repair/replacement of a part or other maintenance activity and the nature of the last maintenance activity were determined and were not found to have influenced the light intensity, DOC and SMH. The LCU age has a statistically significant influence on its light intensity (p=0.024) while the type and maintenance history have no significant influence on its light intensity and composite DOC and SMH (p=0.574, p=0.690, p=0.713 respectively).

  8. Modeling the Residual Stresses in Reactive Resins-Based Materials: a Case Study of Photo-Sensitive Composites for Dental Applications

    Science.gov (United States)

    Grassia, Luigi; D'Amore, Alberto

    2010-06-01

    Residual stresses in reactive resins-based composites are associated to the net volumetric contraction (shrinkage) arising during the cross-linking reactions. Depending on the restoration geometry (the ratio of the free surface area to the volume of the cavity) the frozen-in stresses can be as high as the strength of the dental composites. This is the main reason why the effectiveness and then the durability of restorations with composites remains quite lower than those realized with metal alloys based materials. In this paper we first explore the possibility to circumvent the mathematical complexity arising from the determination of residual stresses in reactive systems three-dimensionally constrained. Then, the results of our modeling approach are applied to a series of commercially available composites showing that almost all samples develop residual stresses such that the restoration undergoes failure as soon as it is realized.

  9. Modeling the Residual Stresses in Reactive Resins-Based Materials: a Case Study of Photo-Sensitive Composites for Dental Applications

    International Nuclear Information System (INIS)

    Grassia, Luigi; D'Amore, Alberto

    2010-01-01

    Residual stresses in reactive resins-based composites are associated to the net volumetric contraction (shrinkage) arising during the cross-linking reactions. Depending on the restoration geometry (the ratio of the free surface area to the volume of the cavity) the frozen-in stresses can be as high as the strength of the dental composites. This is the main reason why the effectiveness and then the durability of restorations with composites remains quite lower than those realized with metal alloys based materials. In this paper we first explore the possibility to circumvent the mathematical complexity arising from the determination of residual stresses in reactive systems three-dimensionally constrained. Then, the results of our modeling approach are applied to a series of commercially available composites showing that almost all samples develop residual stresses such that the restoration undergoes failure as soon as it is realized.

  10. Changes in the temperature of a dental light-cured composite resin by different light-curing units

    Science.gov (United States)

    Rastelli, A. N. S.; Jacomassi, D. P.; Bagnato, V. S.

    2008-08-01

    The purpose of this study was to evaluate the temperature increase during the polymerization process through the use of three different light-curing units with different irradiation times. One argon laser (Innova, Coherent), one halogen (Optilight 501, Demetron), and one blue LED (LEC 1000, MM Optics) LCU with 500 mW/cm2 during 5, 10, 20, 30, 40, 50, and 60 s of irradiation times were used in this study. The composite resin used was a microhybrid Filtek Z-250 (3M/ESPE) at color A2. The samples were made in a metallic mold 2 mm in thickness and 4 mm in diameter and previously light-cured during 40 s. A thermocouple (Model 120 202 EAJ, Fenwal Electronic, Milford, MA, USA) was introduced in the composite resin to measure the temperature increase during the curing process. The highest temperature increase was recorded with a Curing Light 2500 halogen LCU (5 and 31°C after 5 and 60 s, respectively), while the lowest temperature increase was recorded for the Innova LCU based on an argon laser (2 and 11°C after 5 and 60 s, respectively). The temperature recorded for LCU based on a blue LED was 3 and 22°C after 5 and 60 s, respectively. There was a quantifiable amount of heat generated during the visible light curing of a composite resin. The amount of heat generated was influenced by the characteristics of the light-curing units used and the irradiation times.

  11. Color stability of nano-filled, micro-hybrid, and silorane-based dental composite resin materials

    Directory of Open Access Journals (Sweden)

    Mohsen Saud M ALShetili

    2016-01-01

    Full Text Available Aim: The purpose of this study was to investigate the color stability of nano-hybrid, micro-hybrid, and silorane-based composite resin restorative materials upon exposure to staining agents. Materials and Methods: One hundred twenty composites samples were prepared, 40 from each composite material (Filtek ® Z350, Filtek ® P90, and Filtek ® Z250. The specimens were randomly divided into four groups (10 of each sample. The specimens were incubated for 24 h in distilled water and then for 72 h in corresponding mediums (distilled water, red grape juice, green tea, coffee. The color of all the specimens was assessed before and after exposure with a spectrophotometer and total color change (ΔE was calculated using ΔEFNx01 = [(ΔLFNx012 + (ΔaFNx012 + (ΔbFNx012]1/2. The data were analyzed with one-way analysis of variance (ANOVA and Kolmogorov-Smirnov and the means of the solutions were compared by Tukey′s honestly significant difference (HSD (P 0.05 discoloration compared with other media. Conclusions: Within the limitations of this study, it may be concluded that silorane-based composites are more resistant to discoloration than bis-GMA-based composites and coffee had the highest effect on composite discoloration compared to other media.

  12. Immobilization of simulated reducing agent at the surface of SiO2 fillers in dental composite resins.

    Science.gov (United States)

    Shibata, Satoki; Hirata, Isao; Nomura, Yuji; Shirai, Kenichi; Fujitani, Morioki; Shintani, Hideaki; Okazaki, Masayuki

    2007-07-01

    To reduce the leachability of reducing agents from composite resins, immobilization of a simulated reducing agent at the surface of SiO2 fillers was examined. SiO2 plates were immersed in 2% 3-aminopropyltriethoxy silane/ethanol solution, and then immersed in dimethyl sulfoxide with 0.25 wt% 4-dimethyl amino benzoic acid (DMABA), 2.0 wt% 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride, and 0.5 wt% N-hydroxysuccinimide. Wide-scan spectrum of X-ray photoelectron spectroscopy did not detect carbon contamination. However, narrow scan detected an O=C-N peak at 399.8 eV, suggesting that DMABA could be immobilized on silane-coupled SiO2 plates. Further, surface plasmon resonance analysis indicated the adsorption of MMA at the surface of reducing agent-immobilized plate.

  13. Clinical Impact of Dental Adhesives on Postoperative Sensitivity in Class I and Class II Resin-Composite Restorations

    Directory of Open Access Journals (Sweden)

    Manchorova-Veleva Neshka A.

    2015-12-01

    Full Text Available BACKGROUND: Self-etch adhesives are believed to prevent postoperative sensitivity when used under posterior resin-based composite restorations. STUDY OBJECTIVE: A hypothesis that a one-step self-etch adhesive (1-SEA would result in less postoperative sensitivity than a three-step etch-and-rinse adhesive (3-E&RA was tested. PATIENTS AND METHODS: One hundred restorations were placed with a 1-SEA and 100 restorations with a 3-E&RA. Teeth were restored with Filtek Supreme nanofilled resin-composite and were evaluated for sensitivity to cold and masticatory forces at baseline, 7 days, 14 days, 30 days, and 6 months postoperatively. Vitality test scores of the teeth were recorded at the same periods. RESULTS: The evaluation of cold sensitivity intensity (VAS score for all observation periods in both restoration groups did not reveal any statistical significance. The differences in the response time to cold stimulation (0 - 15 sec for the restorations made with a 1-SEA and those made with a separate etch step are statistically insignificant. There are no significant differences in the vitality of the restored teeth at intra- or inter-group comparison. The statistical analysis revealed significant differences in postoperative sensitivity to masticatory forces at postoperative day 14 and day 30 in the 3-E&RA group. CONCLUSIONS: Postoperative sensitivity depends on the type of dentin adhesive used. More intensive complaints of postoperative sensitivity were recorded under masticatory forces at postoperative day 14 and day 30 in 3-E&RA in comparison with 1-SEA.

  14. Bulk-Fill Resin Composites

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Havndrup-Pedersen, Cæcilie; Honoré, Daniel

    2015-01-01

    the restorative procedure. The aim of this study, therefore, was to compare the depth of cure, polymerization contraction, and gap formation in bulk-fill resin composites with those of a conventional resin composite. To achieve this, the depth of cure was assessed in accordance with the International Organization...... for Standardization 4049 standard, and the polymerization contraction was determined using the bonded-disc method. The gap formation was measured at the dentin margin of Class II cavities. Five bulk-fill resin composites were investigated: two high-viscosity (Tetric EvoCeram Bulk Fill, SonicFill) and three low......-viscosity (x-tra base, Venus Bulk Fill, SDR) materials. Compared with the conventional resin composite, the high-viscosity bulk-fill materials exhibited only a small increase (but significant for Tetric EvoCeram Bulk Fill) in depth of cure and polymerization contraction, whereas the low-viscosity bulk...

  15. Effect of photoactivation on the reduction of composite resin contamination.

    Science.gov (United States)

    Pauletti, Natalia A; Girotto, Luiza P S; Leite, Françoise H S; Mario, Débora N

    2017-06-01

    Composite resins are predominantly marketed in developing countries in tube form, and the contents of the tube may be used in numerous procedures for different patients. This represents a problem because of the risk of cross-contamination. This study aimed to evaluate contamination in vitro of the internal contents of composite resin tubes in the dental clinics of a higher-education institution, as well as the effect of photoactivation on the level of contamination. Twenty-five tubes containing composite resin were randomly chosen (by lottery). From each tube, two samples of approximately 2 mm of composite resin were removed, and then one sample, but not the other, was photoactivated. These samples were plated on Brain-Heart Infusion (BHI), Sabouraud and MacConkey agars, and the plates were incubated at 37°C for 24-48 h. Colony counting and Gram staining were performed for subsequent microscopic identification of fungi and bacteria. The non-photoactivated composite resin group presented significantly higher microbial contamination in relation to the photoactivated composite resin group. The photoactivation of camphorquinone present in composite resin produces reactive oxygen species, which might promote cell death of contaminant microorganisms. Thus, although the same tube of composite resin may be used for a number of different patients in the dental clinics of developing countries, the photoactivation process potentially reduces the risk of cross-contamination. © 2017 Eur J Oral Sci.

  16. Heat generated by Er:YAG laser in the pulp chamber of teeth submitted to removal of dental tissue and composite resin

    Science.gov (United States)

    Zanin, Fatima; Brugnera, Aldo, Jr.; Pecora, Jesus D.; Pinheiro, Antonio; Spano, Julio; Barbin, Eduardo; Marchesan, Melissa A.

    2004-05-01

    The knowledge about and control of thermal energy produced by Er:YAG laser after irradiating hard dental tissues and compound resin is important because the pulp, like all vital biological tissue, has a certain capacity for supporting stimulus. The objective of this study was to analyze the thermal variation generated by Er:YAG laser (λ=2.94μm) during the preparation of a Class I cavity in the dental structure and in the removal of microhybrid Z100 (3M) compound resin. An evaluation was made of 30 maxillary human pre-molar teeth from the bank of the Endodontic Laboratory Center of Ribeirao Preto Dental School, Brasil. The sample was divided into 6 groups of 5 teeth each: Group 1, preparation of Class I cavity with Er:YAG laser (350mJ, 3Hz, 343 impulses, 120J, 113 seconds); Group 2, preparation of Class I cavity with Er:YAG laser (350mJ, 4Hz, 343 impulses, 120J, 81 seconds); Group 3, preparation of Class I cavity with Er:YAG laser (350mJ, 6Hz, 343 impulses, 120J, 58 seconds); Group 4, removal of compound resin from Class I preparation with Er:YAG laser (350mJ, 3Hz, 258 impulses, 90J, 85 seconds); Group 5, removal of compound resin from Class I preparation with Er:YAG laser (350mJ, 4Hz, 258 impulses, 90J, 67 seconds); Group 6, removal of compound resin from Class I preparation with Er:YAG laser (350mJ, 6Hz, 258 impulses, 42 seconds). The laser used was KaVo Key 2 (Biberach, Germany), λ=2,94μm, P=3 Watts, pulse duration of 250μs, with air-water cooling. The increase in temperature during dental preparation and the removal of the compound resin was evaluated by means of a Tektronix DMM916 Thermocouple (Consitec, Brasil). The results showed that the application of laser for the removal of the hard dental tissues and for the removal of compound resins with the pulse frequencies 3, 4 and 6 Hz did not generate heating greater than 3.1°C and remained within the histopathological limits permitted for pulp tissue (5.5°C) and there was a significant statistical

  17. A prospective 8-year follow-up of posterior resin composite restorations in permanent teeth of children and adolescents in Public Dental Health Service: reasons for replacement.

    Science.gov (United States)

    Pallesen, Ulla; van Dijken, Jan W V; Halken, Jette; Hallonsten, Anna-Lena; Höigaard, Ruth

    2014-04-01

    The aim of the study was to investigate reasons for replacement and repair of posterior resin composite (RC) restorations placed in permanent teeth of children and adolescents attending Public Dental Health Service in Denmark. All posterior RC placed consecutively by 115 dentists over a period of 4 years were evaluated at baseline and up to 8 years later. The endpoint of each restoration was defined when repair or replacement was performed. The influence of patient, dentist and material factors on reasons for repair or replacement was investigated. A total of 4,355 restorations were placed. Replacements comprised 406 and repairs 125 restorations. The cumulative survival rate at 8 years was 84 %. Failed restorations were most frequently seen due to secondary caries (57 %), post-operative sensitivity (POS) (10 %) and RC fracture (6 %). POS was observed in 1.5 % of the evaluations and reported more often in girls and from teeth restored with a base material. Older dentists showed lower proportion of replaced restorations due to secondary caries than younger dentists. Posterior RC restorations in children and adolescents performed in general practice showed a good durability with annual failure rates of 2 %. The main reason for failure was secondary caries followed by post-operative sensitivity and resin composite fracture. A high proportion of replaced/repaired RC restorations were caused by primary caries in a non-filled surface. Secondary caries was the main reason for failure of RC in children and young adults. More teeth with post-operative sensitivity and a shorter longevity of restorations were observed when a base material was used.

  18. Biphenyl liquid crystalline epoxy resin as a low-shrinkage resin-based dental restorative nanocomposite.

    Science.gov (United States)

    Hsu, Sheng-Hao; Chen, Rung-Shu; Chang, Yuan-Ling; Chen, Min-Huey; Cheng, Kuo-Chung; Su, Wei-Fang

    2012-11-01

    Low-shrinkage resin-based photocurable liquid crystalline epoxy nanocomposite has been investigated with regard to its application as a dental restoration material. The nanocomposite consists of an organic matrix and an inorganic reinforcing filler. The organic matrix is made of liquid crystalline biphenyl epoxy resin (BP), an epoxy resin consisting of cyclohexylmethyl-3,4-epoxycyclohexanecarboxylate (ECH), the photoinitiator 4-octylphenyl phenyliodonium hexafluoroantimonate and the photosensitizer champhorquinone. The inorganic filler is silica nanoparticles (∼70-100 nm). The nanoparticles were modified by an epoxy silane of γ-glycidoxypropyltrimethoxysilane to be compatible with the organic matrix and to chemically bond with the organic matrix after photo curing. By incorporating the BP liquid crystalline (LC) epoxy resin into conventional ECH epoxy resin, the nanocomposite has improved hardness, flexural modulus, water absorption and coefficient of thermal expansion. Although the incorporation of silica filler may dilute the reinforcing effect of crystalline BP, a high silica filler content (∼42 vol.%) was found to increase the physical and chemical properties of the nanocomposite due to the formation of unique microstructures. The microstructure of nanoparticle embedded layers was observed in the nanocomposite using scanning and transmission electron microscopy. This unique microstructure indicates that the crystalline BP and nanoparticles support each other and result in outstanding mechanical properties. The crystalline BP in the LC epoxy resin-based nanocomposite was partially melted during exothermic photopolymerization, and the resin expanded via an order-to-disorder transition. Thus, the post-gelation shrinkage of the LC epoxy resin-based nanocomposite is greatly reduced, ∼50.6% less than in commercialized methacrylate resin-based composites. This LC epoxy nanocomposite demonstrates good physical and chemical properties and good biocompatibility

  19. Evaluation of microshear bond strength of resin composites to enamel of dental adhesive systems associated with Er,Cr:YSGG laser

    Science.gov (United States)

    Cassimiro-Silva, Patricia F.; Zezell, Denise M.; Monteiro, Gabriela Q. d. M.; Benetti, Carolina; de Paula Eduardo, Carlos; Gomes, Anderson S. L.

    2016-02-01

    The aim of this in vitro study was to evaluate the microshear bond strength (μSBS) of resin composite to enamel etching by Er,Cr:YSGG laser with the use of two differents adhesives systems. Fifty freshly extracted human molars halves were embedded in acrylic resin before preparation for the study, making a total of up to 100 available samples. The specimens were randomly assigned into six groups (η=10) according to substrate pre-treatment and adhesive system on the enamel. A two-step self-etching primer system (Clearfil SE Bond) and a universal adhesive used as an etch-andrinse adhesive (Adper Single Bond Universal) were applied to the nonirradiated enamel surface according to manufacturer's instructions, as control groups (Control CF and Control SB, respectively). For the other groups, enamel surfaces were previously irradiated with the Er,Cr:YSGG laser with 0.5 W, 75 mJ and 66 J/cm2 (CF 5 Hz and SB 5 Hz) and 1.25 W, 50 mJ and 44 J/cm2 (CF 15 Hz and SB 15 Hz). Irradiation was performed under air (50%) and water (50%) cooling. An independent t-test was performed to compare the adhesive systems. Mean μSBS ± sd (MPa) for each group was 16.857 +/- 2.61, 17.87 +/- 5.83, 12.23 +/- 2.02, 9.88 +/- 2.26, 15.94 +/- 1.98, 17.62 +/- 2.10, respectively. The control groups and the 50 mJ laser groups showed no statistically significant differences, regardless of the adhesive system used. The results obtained lead us to affirm that the bonding interaction of adhesives to enamel depends not only on the morphological aspects of the dental surface, but also on the characteristics of the adhesive employed and the parameters of the laser.

  20. In vitro evaluation of failure loads of nonmetal cantilevered resin-bonded fixed dental prostheses

    NARCIS (Netherlands)

    van Dalen, A.; Feilzer, A.J.; Kleverlaan, C.J.

    2008-01-01

    Purpose: To evaluate in vitro the influence of fiber reinforcement on the failure loads of resin composite beams, simulating cantilevered two-unit resin-bonded fixed dental prostheses, and compare the results with similarly obtained failure loads of ZrO2 and CoCr beams of a comparable design.

  1. Comparative Effect of Self- or Dual-Curing on Polymerization Kinetics and Mechanical Properties in a Novel, Dental-Resin-Based Composite with Alkaline Filler. Running Title: Resin-Composites with Alkaline Fillers

    Directory of Open Access Journals (Sweden)

    Nicoleta Ilie

    2018-01-01

    Full Text Available Dental bulk-fill restorations with resin-composites (RBC are increasing in popularity, but doubts concerning insufficient curing in depth still disconcert clinicians. An alternative might be offered by modern dual-cured RBCs, which additionally provide bioactive properties. This study assessed the impact of additional light-curing on polymerization kinetics, the degree of conversion (DC and mechanical properties of a novel, dual-cured RBC with alkaline fillers. Since the bioactivity of a material often implies a release of compounds, the mechanical stability in simulated clinical environments was also evaluated. Polymerization kinetics and DC were assessed at 2- and 4-mm specimen depths in real-time up to one hour (n = 6. Incident and transmitted irradiance and radiant exposure were recorded at 2- and 4-mm depths. Micro-mechanical profiles (n = 6 were assessed in 100-µm steps along 6-mm deep specimens at 24 h post-polymerization. Flexural strength and modulus (n = 10 were determined up to three months of immersion in neutral (6.8 and acidic (4 pH conditions. DC variation in time was best described by a sigmoidal function (R2 > 0.98, revealing a retarded (3.4 ± 0.4 min initiation in C=C double bond conversion in self-cured versus dual-cured specimens. The setting reaction kinetic was identical at 2- and 4-mm depths for the self-cure mode. For the dual-cure mode, polymerization initiated at 2-mm depth instantly with light-irradiation, while being retarded (0.8 min at 4-mm depth. The material behaves similarly, irrespective of curing mode or depth, later than 11 min after mixing. Flexural strength and modulus was comparable to regular RBCs and maintained up to three months in both neutral and acidic conditions. Additional light-curing initially accelerates the polymerization kinetic and might help shorten the restauration procedure by hardening the material on demand, however with no effect on the final properties.

  2. Evaluation of fracture toughness and mechanical properties of ternary thiol-ene-methacrylate systems as resin matrix for dental restorative composites.

    Science.gov (United States)

    Beigi, Saeed; Yeganeh, Hamid; Atai, Mohammad

    2013-07-01

    Study and evaluation of fracture toughness, flexural and dynamic mechanical properties, and crosslink density of ternary thiol-ene-methacrylate systems and comparison with corresponding conventional methacrylate system were considered in the present study. Urethane tetra allyl ether monomer (UTAE) was synthesized as ene monomer. Different formulations were prepared based on combination of UTAE, BisGMA/TEGDMA and a tetrathiol monomer (PETMP). The photocuring reaction was conducted under visible light using BD/CQ combination as photoinitiator system. Mechanical properties were evaluated via measuring flexural strength, flexural modulus and fracture toughness. Scanning electron microscopy (SEM) was utilized to study the morphology of the fractured specimen's cross section. Viscoelastic properties of the samples were also determined by dynamic mechanical thermal analysis (DMTA). The same study was performed on a conventional methacrylate system. The data were analyzed and compared by ANOVA and Tukey HSD tests (significance level=0.05). The results showed improvement in fracture toughness of the specimens containing thiol-ene moieties. DMTA revealed a lower glass transition temperature and more homogenous structure for thiol-ene containing specimens in comparison to the system containing merely methacrylate monomer. The flexural modulus and flexural strength of the specimens with higher thiol-ene content were lower than the neat methacrylate system. The SEM micrographs of the fractured surface of specimens with higher methacrylate content were smooth and mirror-like (shiny) which represent brittle fracture. The thiol-ene-methacrylate system can be used as resin matrix of dental composites with enhanced fracture toughness in comparison to the methacrylate analogous. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. A 24-month evaluation of amalgam and resin-based composite restorations: Findings from The National Dental Practice-Based Research Network.

    Science.gov (United States)

    McCracken, Michael S; Gordan, Valeria V; Litaker, Mark S; Funkhouser, Ellen; Fellows, Jeffrey L; Shamp, Douglass G; Qvist, Vibeke; Meral, Jeffrey S; Gilbert, Gregg H

    2013-06-01

    Knowing which factors influence restoration longevity can help clinicians make sound treatment decisions. The authors analyzed data from The National Dental Practice-Based Research Network to identify predictors of early failures of amalgam and resin-based composite (RBC) restorations. In this prospective cohort study, the authors gathered information from clinicians and offices participating in the network. Clinicians completed a baseline data collection form at the time of restoration placement and annually thereafter. Data collected included patient factors, practice factors and dentist factors, and the authors analyzed them by using mixed-model logistic regression. A total of 226 practitioners followed up 6,218 direct restorations in 3,855 patients; 386 restorations failed (6.2 percent) during the mean (standard deviation) follow-up of 23.7 (8.8) months. The number of tooth surfaces restored at baseline helped predict subsequent restoration failure; restorations with four or more restored surfaces were more than four times more likely to fail. Restorative material was not associated significantly with longevity; neither was tooth type. Older patient age was associated highly with failure (P amalgam and RBC restorations: patient's age, a higher number of surfaces restored at baseline, the dentist's sex and the practice workload. Material choice was not significantly predictive in these early results. Practical Implications. If clinicians can recognize and identify the risk factors associated with early restoration failure, more effective treatment plans may be offered to the patient.

  4. Bactericidal and Bioactive Dental Composites.

    Science.gov (United States)

    Chatzistavrou, Xanthippi; Lefkelidou, Anna; Papadopoulou, Lambrini; Pavlidou, Eleni; Paraskevopoulos, Konstantinos M; Fenno, J Christopher; Flannagan, Susan; González-Cabezas, Carlos; Kotsanos, Nikos; Papagerakis, Petros

    2018-01-01

    Aim: Antimicrobial and bioactive restorative materials are needed to develop a bacteria free environment and tight bond with the surrounding tissue, preventing the spread of secondary caries and thus extending the lifetime of dental restorations. The characteristic properties of new dental bioactive and antibacterial composites are presented in this work. The new composites have been microstructurally characterized and both long and short term properties have been studied. Methods: The Ag-doped sol-gel derived bioactive glass (Ag-BG) was incorporated into resin composite in concentrations 5, 10, and 15 wt.%, to fabricate new Ag-doped bioactive and antibacterial dental composites (Ag-BGCOMP). The microstructural properties and elemental analysis of the developed Ag-BGCOMP was observed. The total bond strength (TBS) was measured immediately and after long term of immersion in medium using microtensile testing. The capability of Ag-BGCOMPs to form apatite layer on their surface after immersion in Simulated Body Fluid (SBF) as well as the bacteria growth inhibition in a biofilm formed by Streptococcus mutans ( S. mutans ) were evaluated. Results: Homogeneous distribution of Ag-BG particles into the resin composite was observed microstructurally for all Ag-BGCOMPs. The TBS measurements showed non-statistically significant difference between control samples (Ag-BG 0 wt.%) and Ag-BGCOMP specimens. Moreover, the total bond strength between the surrounding tooth tissue and the material of restoration does not present any statistically significant change for all the cases even after 3 months of immersion in the medium. The bioactivity of the Ag-BGCOMPs was also shown by the formation of a calcium-phosphate layer on the surface of the specimens after immersion in SBF. Antibacterial activity was observed for all Ag-BGCOMPs, statistically significant differences were observed between control samples and Ag-BGCOMPs. Accordingly, the number of dead bacteria in the biofilm found

  5. Conjugation of diisocyanate side chains to dimethacrylate reduces polymerization shrinkage and increases the hardness of composite resins

    Directory of Open Access Journals (Sweden)

    Yih-Dean Jan

    2014-04-01

    Conclusion: Conjugation of diisocyanate side chains to dimethacrylate represents an effective means of reducing polymerization shrinkage and increasing the surface hardness of dental composite resins.

  6. Resin impregnation process for producing a resin-fiber composite

    Science.gov (United States)

    Palmer, Raymond J. (Inventor); Moore, William E. (Inventor)

    1994-01-01

    Process for vacuum impregnation of a dry fiber reinforcement with a curable resin to produce a resin-fiber composite, by drawing a vacuum to permit flow of curable liquid resin into and through a fiber reinforcement to impregnate same and curing the resin-impregnated fiber reinforcement at a sufficient temperature and pressure to effect final curing. Both vacuum and positive pressure, e.g. autoclave pressure, are applied to the dry fiber reinforcement prior to application of heat and prior to any resin flow to compact the dry fiber reinforcement, and produce a resin-fiber composite of reduced weight, thickness and resin content, and improved mechanical properties. Preferably both a vacuum and positive pressure, e.g. autoclave pressure, are also applied during final curing.

  7. The Bond Strength of Composite Resin to Dental Casting Alloys Using an Electro-Chemical Tin Plating System.

    Science.gov (United States)

    1985-06-01

    and ultrasonically cleaned for 10 minutes in 18 percent hydrochloric acid to remove the black film 26 Figure 3. Completed Castings Removed from...of Isosit to electrolytically etched nickel-chromium substrate. J. Dent. Res., 62: 220. Blankenau, R.J., Kelsey, W.P., Cavel , W.T., and Blankenau, D...position of Assistant Director Area Dental Laboratory, Kadena AFB, Okinawa. He will assume this position in August, 1985. FILMED 12-85 DTIC

  8. In Vitro Color Change of Three Dental Veneering Resins in Tea, Coffee and Tamarind Extracts

    Directory of Open Access Journals (Sweden)

    S. Muttagi

    2011-09-01

    Full Text Available Objective: To study the in vitro color changes of three dental resin veneering materials when immersed in tea, coffee and tamarind extracts.Materials and Methods: The color changes of heat polymerized tooth colored acrylic resin (Stellondetrey, B, F14, DPI Dental products of India Ltd, Mumbai, auto polymerized tooth colored acrylic resin (DPI, B, QV5, DPI Dental products of India Ltd, Mumbai andlight polymerized resin composite (Herculite XRV, Enamel A2, part no. 22860, lot no. 910437, Kerr Corporation, West Collins Avenue, Orange, CA, USA when immersed in water extracts of tea (Tata Tea Ltd. Bangalore, India, coffee (Tata Coffee Ltd. Coorg, Indiaand tamarind were evaluated using computer vision systems. The color images were recorded in R (red, G (green and B (blue form and converted into H (hue, S (saturationand V (value.Results: Significant color change occurred for auto polymerized tooth colored acrylic resin in tamarind extract, for heat polymerized tooth colored acrylic resin in tea extract andfor light polymerized resin composite in coffee extract. Auto polymerized tooth colored acrylic resin samples showed an overall higher color change. However, for all the material samples coffee extract produced more color change.Conclusion: These results suggest that the color stability of the resins is influenced by the presence of secondary metabolites such as tartaric acid, tannins, caffeine, saponins and phenols in tamarind, tea and coffee extracts.

  9. Thermal cycling effects on adhesion of resin-bovine enamel junction among different composite resins.

    Science.gov (United States)

    Chen, Wen-Cheng; Ko, Chia-Ling; Wu, Hui-Yu; Lai, Pei-Ling; Shih, Chi-Jen

    2014-10-01

    Thermal cycling is used to mimic the changes in oral cavity temperature experienced by composite resins when used clinically. The purpose of this study is to assess the thermal cycling effects of in-house produced composite resin on bonding strength. The dicalcium phosphate anhydrous filler surfaces are modified using nanocrystals and silanization (w/NP/Si). The resin is compared with commercially available composite resins Filtek Z250, Z350, and glass ionomer restorative material GIC Fuji-II LC (control). Different composite resins were filled into the dental enamel of bovine teeth. The bond force and resin-enamel junction graphical structures of the samples were determined after thermal cycling between 5 and 55°C in deionized water for 600 cycles. After thermal cycling, the w/NP/Si 30wt%, 50wt% and Filtek Z250, Z350 groups showed higher shear forces than glass ionomer GIC, and w/NP/Si 50wt% had the highest shear force. Through SEM observations, more of the fillings with w/NP/Si 30wt% and w/NP/Si 50wt% groups flowed into the enamel tubule, forming closed tubules with the composite resins. The push-out force is proportional to the resin flow depth and uniformity. The push-out tubule pore and resin shear pattern is the most uniform and consistent in the w/NP/Si 50wt% group. Accordingly, this developed composite resin maintains great mechanical properties after thermal cycling. Thus, it has the potential to be used in a clinical setting when restoring non-carious cervical lesions. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Amalgam stained dentin: a proper substrate for bonding resin composite?

    NARCIS (Netherlands)

    Scholtanus, J.D.

    2016-01-01

    Nowadays the use of dental amalgam is mostly abandoned and substituted by tooth colored resin composites that can be bonded to teeth tissues by adhesive techniques. The aim of this thesis was to find out whether dark stained dentin, as often observed after removal of amalgam restorations and

  11. Resin composite repair: Quantitative microleakage evaluation of resin-resin and resin-tooth interfaces with different surface treatments

    OpenAIRE

    Celik, Cigdem; Cehreli, Sevi Burcak; Arhun, Neslihan

    2015-01-01

    Objective: The aim was to evaluate the effect of different adhesive systems and surface treatments on the integrity of resin-resin and resin-tooth interfaces after partial removal of preexisting resin composites using quantitative image analysis for microleakage testing protocol. Materials and Methods: A total of 80 human molar teeth were restored with either of the resin composites (Filtek Z250/GrandioSO) occlusally. The teeth were thermocycled (1000?). Mesial and distal 1/3 parts of the res...

  12. Effect of Amount of 3-Methacryloxy Propyl Thrimethoxysilane Coupling Agent and Nano Filling Structure on Physic-Mechanical Properties of Dental Resin Composite

    Directory of Open Access Journals (Sweden)

    Farbod Tondnevis

    2017-07-01

    Full Text Available Many researchers in the field of dental polymeric base nano composite investigated the effect filling morphology and filling material content on mechanical and physical properties of construction after setting reaction. Our present study concentrated on the effect of ϒ metacryloxy propyloxt tri metoxy silane (ϒ MPS content as coupling agent (orgnic material on physical and mechanical performance of nano composite material. It was shown that despite of contraction after setting reaction, all this properties improved and efficient silanization can efficiently affect structural integrity of dental filling nano composite

  13. Inhibition of odontogenic differentiation of human dental pulp cells by dental resin monomers

    OpenAIRE

    Kwon, Ji Hyun; Park, Hee Chul; Zhu, Tingting; Yang, Hyeong-Cheol

    2015-01-01

    Background Dental resin monomers that are leached from the resin matrix due to incomplete polymerization can affect the viability and various functions of oral tissues and cells. In this study, the effects of triethylene glycol dimethacrylate (TEGDMA) and 2-hydroxyethyl methacrylate (HEMA) on odontogenic differentiation of human dental pulp cells (HDPCs) were examined. To mimic clinical situations, dental pulp cells were treated with resin monomers for 24?h prior to the analysis of alkaline p...

  14. Effects of 35% Carbamide Peroxide Gel on Surface Roughness and Hardness of Composite Resins

    OpenAIRE

    Sharafeddin, F.; Jamalipour, GR.

    2010-01-01

    Objective: Bleaching agents may not be safe for dental materials. The purpose of this in-vitro study was to evaluate the effects of Opalescent Quick ?in-office bleaching gel? containing 35% carbamide peroxide on the surface roughness and hardness of microfilled (Heliomolar) and hybride (Spectrum TPH) composite resins. Materials and Methods: Twenty specimens of Spectrum TPH composite resins and twenty Heliomolar composite resins were fabricated using a metallic ring (6.5 mm diameter and 2.5 mm...

  15. Carbon-Fiber Framework for Full-Arch Implant-Supported Fixed Dental Prostheses Supporting Resin-Based Composite and Lithium Disilicate Ceramic Crowns: Case Report and Description of Features.

    Science.gov (United States)

    Castorina, Giuseppe

    2017-12-15

    This case report presents a new approach for shock-absorbing carbon-fiber composite frameworks for full-arch implant-supported fixed dental prostheses supporting resin-based and lithium disilicate ceramic crowns. It describes the characteristics of the materials used, the procedures for implementing the framework, and the requirements to achieve the best mechanical and clinical properties. The result is a full-arch prosthesis with masticatory load shock-absorption capacities, chemical bonding between materials, good esthetics, and wear similar to natural enamel. A 24-month follow-up full-arch bimaxillary implant-supported rehabilitation, performed with computer-guided surgery, is described.

  16. In vitro evaluation of failure loads of nonmetal cantilevered resin-bonded fixed dental prostheses.

    Science.gov (United States)

    van Dalen, Andy; Feilzer, Albert J; Kleverlaan, Cornelis J

    2008-12-01

    To evaluate in vitro the influence of fiber reinforcement on the failure loads of resin composite beams, simulating cantilevered two-unit resin-bonded fixed dental prostheses, and compare the results with similarly obtained failure loads of ZrO2 and CoCr beams of a comparable design. Peel tests were performed using resin composite, fiber-reinforced resin composite, and zirconia beams, simulating two-unit cantilevered resin-bonded fixed dental prostheses, luted with Panavia F2.0 onto flat-ground buccal surfaces of bovine mandibular incisors. The recorded failure loads were compared with those of CoCr beams of a similar size and design from earlier research. Finite element analysis revealed the stress concentrations within the cement layers at failure. The failure loads (N) of the peel tests, depending on the beam type and including the type of failure, were statistically analyzed. The highest failure values were obtained with the fiber-reinforced resin composite beams, which were luted with the exposed fibers directly on the bovine enamel. Finite element analysis showed that peak stress locations depend on the beam type and facilitate the explanation of the different failure modes. Fiber-reinforcement of simulated two-unit cantilevered resin composite resin-bonded fixed dental prostheses does not necessarily lead to higher failure loads. This study identified significant differences in peel failure loads between identical specimens, depending on whether or not the fiber reinforcement was exposed on the luting surface. Further research needs to be carried out regarding the combination of resin composite and fiber reinforcement.

  17. Subsurface degradation of resin-based composites.

    Science.gov (United States)

    Bagheri, Rafat; Tyas, Martin J; Burrow, Michael F

    2007-08-01

    To determine the depth of a degraded subsurface layer produced in dental composites as a result of exposure to lactic acid or NaOH, by observing the penetration of AgNO(3) solution. Specimens were prepared from four resin composites; Point 4 (Kerr), Premise (Kerr), Filtek Supreme (3M/ESPE), Ceram X (Dentsply), and two polyacid-modified resin composites; Dyract (Dentsply) and F2000 (3M/ESPE). The specimens were immersed in distilled water for 1 week, transferred to one of three aqueous media at 60 degrees C for 2 weeks; distilled water, 0.01mol/L lactic acid or 0.1N NaOH, washed and immersed in 50% (w/w) aqueous silver nitrate for 10 days at 60 degrees C and placed in a photodeveloper solution. After reduction of the silver, specimens were embedded in epoxy resin, sectioned and polished, coated with carbon, and examined by backscattered mode scanning electron microscopy. The depth of silver penetration into the degraded area was measured from the SEM micrographs. Energy dispersive analysis X-ray (EDAX) was used to confirm the presence of silver. NaOH produced the greatest depth of degradation and lactic acid the least. Premise showed the greatest depth of silver penetration when subjected to NaOH, and Filtek Supreme the second with peeling of the surface and cracking, whereas F2000 and Point 4 showed the least in NaOH and lactic acid. ANOVA and Tukey's test showed that the depth of silver penetration was material and solution dependent, and the differences were significant for most of the materials (P<0.05).

  18. Volumetric polymerization shrinkage of contemporary composite resins

    OpenAIRE

    Nagem Filho, Halim; Nagem, Haline Drumond; Francisconi, Paulo Afonso Silveira; Franco, Eduardo Batista; Mondelli, Rafael Francisco Lia; Coutinho, Kennedy Queiroz

    2007-01-01

    The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill ...

  19. Effect of configuration factor on gap formation in hybrid composite resin, low-shrinkage composite resin and resin-modified glass ionomer.

    Science.gov (United States)

    Boroujeni, Parvin M; Mousavinasab, Sayyed M; Hasanli, Elham

    2015-05-01

    Polymerization shrinkage is one of the important factors in creation of gap between dental structure and composite resin restorations. The aim of this study was to evaluate the effect of configuration factor (C-factor) on gap formation in a hybrid composite resin, a low shrinkage composite resin and a resin modified glass ionomer restorative material. Cylindrical dentin cavities with 5.0 mm diameter and three different depths (1.0, 2.0 and 3.0 mm) were prepared on the occlusal surface of 99 human molars and the cavities assigned into three groups (each of 33). Each group contained three subgroups depend on the different depths and then cavities restored using resin modified glass ionomer (Fuji II LC Improved) and two type composite resins (Filtek P90 and Filtek Z250). Then the restorations were cut into two sections in a mesiodistal direction in the middle of restorations. Gaps were measured on mesial, distal and pulpal floor of the cavities, using a stereomicroscope. Data analyses using Kruskal-Wallist and Mann-Whitney tests. Increasing C-factor from 1.8 to 3.4 had no effect on the gap formation in two type composite resins, but Fuji II LC Improved showed significant effect of increasing C-factor on gap formation. Taken together, when C-factor increased from 1.8 up to 3.4 had no significant effect on gap formation in two tested resin composites. Although, Filtek P90 restorations showed smaller gap formation in cavities walls compared to Filtek Z250 restorations. High C-factor values generated the largest gap formation. Silorane-based composite was more efficient for cavity sealing than methacrylate-based composites and resin modified glass ionomer. © 2014 Wiley Publishing Asia Pty Ltd.

  20. Foam, Foam-resin composite and method of making a foam-resin composite

    Science.gov (United States)

    Cranston, John A. (Inventor); MacArthur, Doug E. (Inventor)

    1995-01-01

    This invention relates to a foam, a foam-resin composite and a method of making foam-resin composites. The foam set forth in this invention comprises a urethane modified polyisocyanurate derived from an aromatic amino polyol and a polyether polyol. In addition to the polyisocyanurate foam, the composite of this invention further contains a resin layer, wherein the resin may be epoxy, bismaleimide, or phenolic resin. Such resins generally require cure or post-cure temperatures of at least 350.degree. F.

  1. SEM and elemental analysis of composite resins

    International Nuclear Information System (INIS)

    Hosoda, H.; Yamada, T.; Inokoshi, S.

    1990-01-01

    Twenty-four chemically cured, 21 light-cured anterior, three light-cured anterior/posterior, and 18 light-cured posterior composite resins were examined using scanning electron microscopy, and the elemental composition of their filler particles was analyzed with an energy dispersive electron probe microanalyzer. According to the results obtained, the composite resins were divided into five groups (traditional, microfilled type, submicrofilled type, hybrid type, and semihybrid), with two additional hypothetical categories (microfilled and hybrid). Characteristics of each type were described with clinical indications for selective guidance of respective composite resins for clinical use

  2. Effect of dental surface treatment with Nd:YAG and Er:YAG lasers on bond strength of resin composite to recently bleached enamel.

    Science.gov (United States)

    Rocha Gomes Torres, Carlos; Caneppele, Taciana Marco Ferraz; Del Moral de Lazari, Regina; Ribeiro, Carolina Ferraz; Borges, Alessandra Buhler

    2012-07-01

    The aim of this work is to evaluate the effect of surface treatment with Er:YAG and Nd:YAG lasers on resin composite bond strength to recently bleached enamel. In this study, 120 bovine incisors were distributed into two groups: group C: without bleaching treatment; group B: bleached with 35% hydrogen peroxide. Each group was divided into three subgroups: subgroup N: without laser treatment; subgroup Nd: irradiation with Nd:YAG laser; subgroup Er: irradiation with Er:YAG laser. The adhesive system (Adper Single Bond 2) was then applied and composite buildups were constructed with Filtek Supreme composite. The teeth were sectioned to obtain enamel-resin sticks (1 × 1 mm) and submitted to microtensile bond testing. The data were statistically analyzed by the ANOVA and Tukey tests. The bond strength values in the bleached control group (5.57 MPa) presented a significant difference in comparison to the group bleached and irradiated with Er:YAG laser (13.18 MPa) or Nd:YAG (25.67 MPa). The non-bleached control group presented mean values of 30.92 MPa, with statistical difference of all the others groups. The use of Nd:YAG and Er:YAG lasers on bleached specimens was able to improve the bond strengths of them.

  3. Microshear bond strength between restorative composites and resin cements

    OpenAIRE

    Rubens Nazareno GARCIA; Mário Fernando de GÓES; Marcelo GIANNINI

    2008-01-01

    Introduction and objective: The techniques of adhesive cementationhave been widely used in dental restoration. The purpose of this studywas to evaluate the microshear bond strength between restorativecomposites and resin cements. Material and methods: Twenty composites blocks were prepared in order to obtain a flat surface, using 600-grid sandpaper. The samples were randomly divided in four groups(n=15) according to the experimental groups: [1] Z250 block + Single Bond + cylinder of RelyX ARC...

  4. Resin selection criteria for tough composite structures

    Science.gov (United States)

    Chamis, C. C.; Smith, G. T.

    1983-01-01

    Resin selection criteria are derived using a structured methodology consisting of an upward integrated mechanistic theory and its inverse (top-down structured theory). These criteria are expressed in a "criteria selection space" which are used to identify resin bulk properties for improved composite "toughness". The resin selection criteria correlate with a variety of experimental data including laminate strength, elevated temperature effects and impact resistance.

  5. Bonding of Glass Ceramic and Indirect Composite to Non-aged and Aged Resin Composite

    NARCIS (Netherlands)

    Gresnigt, Marco; Ozcan, Mutlu; Muis, Maarten; Kalk, Warner

    2012-01-01

    Purpose: Since adhesion of the restorative materials to pre-polymerized or aged resin composites presents a challenge to the clinicians, existing restorations are often removed and remade prior to cementation of fixed dental prostheses (FDPs). This study evaluated bond strength of non-aged and aged

  6. Treatment planning and smile design using composite resin.

    Science.gov (United States)

    Marus, Robert

    2006-05-01

    Recent advances in dental materials and adhesive protocols have expanded the restorative procedures available to today's clinicians. Used in combination with proper treatment planning, these innovations enable dental professionals to provide enhanced aesthetic care that achieves the increasing expectations of their patients. Using a case presentation, this article will document the steps required to harmoniously integrate smile design, material selection, and patient communication that are involved in the provisional of aesthetic dental care. This article discusses the utilization of composite resin as a tool to enhance the patient's smile. Upon reading this article, the reader should: Become familiar with a smile-enhancing technique which can be completed in one office visit. Realize the benefits that intraoral composite mockups offer in terms of prototyping and confirming patient satisfaction.

  7. Posterior bulk-filled resin composite restorations.

    DEFF Research Database (Denmark)

    van Dijken, Jan WV; Pallesen, Ulla

    2016-01-01

    Purpose/aim: To evaluate in a randomized controlled study the 5-year clinical durability of a flowable resin composite bulk-fill technique in Class I and Class II restorations. Materials and methods: 38 pairs Class I and 62 pairs Class II restorations were placed in 44 male and 42 female (mean age...... 52.4 years). Each patient received at least two, as similar as possible, extended Class I or Class II restorations. In all cavities, a 1-step self-etch adhesive (Xeno V+) was applied. Randomized, one of the cavities of each pair received the flowable bulk-filled resin composite (SDR), in increments...... up to 4mm as needed to fill the cavity 2mm short of the occlusal cavosurface. The occlusal part was completed with the nano-hybrid resin composite (Ceram X mono+). In the other cavity, the resin composite-only (Ceram X mono+) was placed in 2mm increments. The restorations were evaluated using...

  8. Design of a metal primer containing a dithiooctanoate monomer and a phosphonic acid monomer for bonding of prosthetic light-curing resin composite to gold, dental precious and non-precious metal alloys.

    Science.gov (United States)

    Ikemura, Kunio; Fujii, Toshihide; Negoro, Noriyuki; Endo, Takeshi; Kadoma, Yoshinori

    2011-01-01

    The effect of metal primers on adhesion of a resin composite to dental metal alloys was investigated. Experimental primers containing a dithiooctanoate monomer [10-methacryloyloxydecyl 6,8-dithiooctanoate (10-MDDT) or 6-methacryloyloxyhexyl 6,8-dithiooctanoate (6-MHDT)] and a phosphonic acid monomer [6-methacryloyloxyhexyl phosphonoacetate (6-MHPA) or 6-methacryloyloxyhexyl 3-phosphonopropionate (6-MHPP)] were prepared. After treating Au, Au alloy, Ag alloy, Au-Ag-Pd alloy, and Ni-Cr alloy with the experimental primers, their shear bond strengths (SBSs) with a prosthetic light-curing resin composite (Solidex, Shofu Inc., Japan) were measured after 1-day storage followed by 5,000 thermal cycles. The SBSs between Solidex and the primer-treated metals which were incubated in air at 50°C for 2 months were further measured. Results showed that the SBSs [mean (SD)] of all metal adherends treated with primer DT-PA-1 (5.0 wt% 10-MDDT, 1.0 wt% 6-MHPA) ranged between 31.2 (5.2) and 34.5 (5.8) MPa. The SBSs of the primer-treated metals did not degrade after 2-month incubation at 50°C. Therefore, a combined primer application consisting of a dithiooctanoate monomer and a phosphonic acid monomer provided efficacious bonding to Au as well as precious and non-precious metal alloys.

  9. Statistical failure analysis of adhesive resin cement bonded dental ceramics

    Science.gov (United States)

    Wang, Yaou; Katsube, Noriko; Seghi, Robert R; Rokhlin, Stanislav I.

    2007-01-01

    The goal of this work is to quantitatively examine the effect of adhesive resin cement on the probability of crack initiation from the internal surface of ceramic dental restorations. The possible crack bridging mechanism and residual stress effect of the resin cement on the ceramic surface are examined. Based on the fracture-mechanics-based failure probability model, we predict the failure probability of glass-ceramic disks bonded to simulated dentin subjected to indentation loads. The theoretical predictions match experimental data suggesting that both resin bridging and shrinkage plays an important role and need to be considered for accurate prognostics to occur. PMID:18670583

  10. Volumetric polymerization shrinkage of contemporary composite resins

    Directory of Open Access Journals (Sweden)

    Halim Nagem Filho

    2007-10-01

    Full Text Available The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill Magic, Alert, and Solitaire to determine whether there are differences among these materials. The tests were conducted with precision of 0.1 mg. The volumetric shrinkage was measured by hydrostatic weighing before and after polymerization and calculated by known mathematical equations. One-way ANOVA (a or = 0.05 was used to determine statistically significant differences in volumetric shrinkage among the tested composite resins. Suprafill (1.87±0.01 and Definite (1.89±0.01 shrank significantly less than the other composite resins. SureFil (2.01±0.06, Filtek Z250 (1.99±0.03, and Fill Magic (2.02±0.02 presented intermediate levels of polymerization shrinkage. Alert and Solitaire presented the highest degree of polymerization shrinkage. Knowing the polymerization shrinkage rates of the commercially available composite resins, the dentist would be able to choose between using composite resins with lower polymerization shrinkage rates or adopting technical or operational procedures to minimize the adverse effects deriving from resin contraction during light-activation.

  11. Mechanical evaluation of five flowable resin composites by the dynamic micro-indentation method.

    Science.gov (United States)

    Hirayama, Satoshi; Iwai, Hirotoshi; Tanimoto, Yasuhiro

    2014-01-01

    Measurement of the strength of brittle materials, such as resin composites, is extremely difficult. Micro-indentation hardness testing is a convenient way of investigating the mechanical properties of a small volume of material. In this study, the mechanical properties of five commercially available flowable resin composites were investigated by the dynamic micro-indentation method. Additionally, the effects of inorganic-filler content on the dynamic hardness and elastic modulus of flowable composites obtained by this method were investigated. The weight percentages of the inorganic fillers in the resin composites were determined by the ashing technique. The results indicate that the mechanical properties of flowable composites are affected by not only the filler content but also the properties of the resin matrix. In conclusion, the dynamic micro-indentation method is a useful technique for determining the mechanical behavior of dental resin composites as brittle material.

  12. Fatigue resistance of CAD/CAM resin composite molar crowns.

    Science.gov (United States)

    Shembish, Fatma A; Tong, Hui; Kaizer, Marina; Janal, Malvin N; Thompson, Van P; Opdam, Niek J; Zhang, Yu

    2016-04-01

    To demonstrate the fatigue behavior of CAD/CAM resin composite molar crowns using a mouth-motion step-stress fatigue test. Monolithic leucite-reinforced glass-ceramic crowns were used as a reference. Fully anatomically shaped monolithic resin composite molar crowns (Lava Ultimate, n=24) and leucite reinforced glass-ceramic crowns (IPS Empress CAD, n=24) were fabricated using CAD/CAM systems. Crowns were cemented on aged dentin-like resin composite tooth replicas (Filtek Z100) with resin-based cements (RelyX Ultimate for Lava Ultimate or Multilink Automix for IPS Empress). Three step-stress profiles (aggressive, moderate and mild) were employed for the accelerated sliding-contact mouth-motion fatigue test. Twenty one crowns from each group were randomly distributed among these three profiles (1:2:4). Failure was designated as chip-off or bulk fracture. Optical and electron microscopes were used to examine the occlusal surface and subsurface damages, as well as the material microstructures. The resin composite crowns showed only minor occlusal damage during mouth-motion step-stress fatigue loading up to 1700N. Cross-sectional views revealed contact-induced cone cracks in all specimens, and flexural radial cracks in 2 crowns. Both cone and radial cracks were relatively small compared to the crown thickness. Extending these cracks to the threshold for catastrophic failure would require much higher indentation loads or more loading cycles. In contrast, all of the glass-ceramic crowns fractured, starting at loads of approximately 450N. Monolithic CAD/CAM resin composite crowns endure, with only superficial damage, fatigue loads 3-4 times higher than those causing catastrophic failure in glass-ceramic CAD crowns. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  13. Polymerization shrinkage stress of composite resins and resin cements - What do we need to know?

    Science.gov (United States)

    Soares, Carlos José; Faria-E-Silva, André Luis; Rodrigues, Monise de Paula; Vilela, Andomar Bruno Fernandes; Pfeifer, Carmem Silvia; Tantbirojn, Daranee; Versluis, Antheunis

    2017-08-28

    Polymerization shrinkage stress of resin-based materials have been related to several unwanted clinical consequences, such as enamel crack propagation, cusp deflection, marginal and internal gaps, and decreased bond strength. Despite the absence of strong evidence relating polymerization shrinkage to secondary caries or fracture of posterior teeth, shrinkage stress has been associated with post-operative sensitivity and marginal stain. The latter is often erroneously used as a criterion for replacement of composite restorations. Therefore, an indirect correlation can emerge between shrinkage stress and the longevity of composite restorations or resin-bonded ceramic restorations. The relationship between shrinkage and stress can be best studied in laboratory experiments and a combination of various methodologies. The objective of this review article is to discuss the concept and consequences of polymerization shrinkage and shrinkage stress of composite resins and resin cements. Literature relating to polymerization shrinkage and shrinkage stress generation, research methodologies, and contributing factors are selected and reviewed. Clinical techniques that could reduce shrinkage stress and new developments on low-shrink dental materials are also discussed.

  14. Two-body wear simulation influence on some direct and indirect dental resin biocomposites - A qualitative analysis.

    Science.gov (United States)

    Caracostea, Adriana; Morar, Nadina; Florea, Adrian; Soanca, Andrada; Badea, Mindra Eugenia

    2016-01-01

    The aim of this study was to qualitatively assess the outcomes of two in vitro aging methods, thermal-cycling and twobody wear simulation accomplished with a dual-axis chewing device, on the surface characteristics of eight direct and indirect dental resin biocomposites. Eighty mesial-occlusal-distal dental cavities were restored with four direct nanohybrid composite materials and with four nano- and micro-hybrid lab-fabricated resin composite inlays. After the restored teeth were subjected to thermal-cycling and wear simulation based on mechanical loading, the surface texture features of the restorations were separately analysed for each of the methods, on epoxy resin models using a digital camera, computer-aided-design system, optical stereo-microscopy and scanning electron microscopy. All the dental restorative resin based composites used in this investigation displayed different cyclic wear patterns after undergoing mechanical loading. After thermal-cycling, the group of resin composite inlays showed a better adaptation, a smoother and more polished occlusal surface compared with direct restorative materials. Only two of direct nanohybrid resin composites performed better after two aging methods. One nanohybrid and the other two microhybrid resin inlays did not perform as expected when they were subjected to simulated wear compared to the rest of test materials. The use of the two-body wear simulation method revealed important information about the behavior of the dental resin-based composites when multiple oral factors are involved in a lab-simulated condition. Furthermore, the macro- and micro-morphological analysis showed different abrasion patterns among the materials being tested according to the filler percentage and distribution of the particles within the resin matrix.

  15. Flexural properties of experimental nanofiber reinforced composite are affected by resin composition and nanofiber/resin ratio.

    Science.gov (United States)

    Vidotti, Hugo A; Manso, Adriana P; Leung, Victor; do Valle, Accácio L; Ko, Frank; Carvalho, Ricardo M

    2015-09-01

    To evaluate the influence of different resin blends concentrations and nanofibers mass ratio on flexural properties of experimental Poliacrylonitrile (PAN) nanofibers reinforced composites. Poliacrylonitrile (PAN) nanofibers mats were produced by electrospinning and characterized by tensile testing and scanning electron microscopy (SEM). Experimental resin-fiber composite beams were manufactured by infiltrating PAN nanofiber mats with varied concentrations of BisGMA-TEGDMA resin blends (BisGMA/TEGDMA: 30/70, 50/50 and 70/30weight%). The mass ratio of fiber to resin varied from 0% to 8%. Beams were cured and stored in water at 37°C. Flexural strength (FS), flexural modulus (FM) and work of fracture (WF) were evaluated by three-point bending test after 24h storage. The tensile properties of the PAN nanofibers indicated an anisotropic behavior being always higher when tested in a direction perpendicular to the rotation of the collector drum. Except for WF, the other flexural properties (FS and FM) were always higher as the ratio of BisGMA to TEGDMA increased in the neat resin beams. The addition of different ratios of PAN fibers did not affect FS and FM of the composite beams as compared to neat resin beams (p>0.05). However, the addition of fibers significantly increased the WF of the composite beams, and this was more evident for the blends with higher TEGDMA ratios (presin blends did not negatively affect the properties of the composite and resulted in an increase in toughness that is a desirable property for a candidate material for prosthodontics application. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  16. Polymerization Behavior and Mechanical Properties of High-Viscosity Bulk Fill and Low Shrinkage Resin Composites.

    Science.gov (United States)

    Shibasaki, S; Takamizawa, T; Nojiri, K; Imai, A; Tsujimoto, A; Endo, H; Suzuki, S; Suda, S; Barkmeier, W W; Latta, M A; Miyazaki, M

    The present study determined the mechanical properties and volumetric polymerization shrinkage of different categories of resin composite. Three high viscosity bulk fill resin composites were tested: Tetric EvoCeram Bulk Fill (TB, Ivoclar Vivadent), Filtek Bulk Fill posterior restorative (FB, 3M ESPE), and Sonic Fill (SF, Kerr Corp). Two low-shrinkage resin composites, Kalore (KL, GC Corp) and Filtek LS Posterior (LS, 3M ESPE), were used. Three conventional resin composites, Herculite Ultra (HU, Kerr Corp), Estelite ∑ Quick (EQ, Tokuyama Dental), and Filtek Supreme Ultra (SU, 3M ESPE), were used as comparison materials. Following ISO Specification 4049, six specimens for each resin composite were used to determine flexural strength, elastic modulus, and resilience. Volumetric polymerization shrinkage was determined using a water-filled dilatometer. Data were evaluated using analysis of variance followed by Tukey's honestly significant difference test (α=0.05). The flexural strength of the resin composites ranged from 115.4 to 148.1 MPa, the elastic modulus ranged from 5.6 to 13.4 GPa, and the resilience ranged from 0.70 to 1.0 MJ/m 3 . There were significant differences in flexural properties between the materials but no clear outliers. Volumetric changes as a function of time over a duration of 180 seconds depended on the type of resin composite. However, for all the resin composites, apart from LS, volumetric shrinkage began soon after the start of light irradiation, and a rapid decrease in volume during light irradiation followed by a slower decrease was observed. The low shrinkage resin composites KL and LS showed significantly lower volumetric shrinkage than the other tested materials at the measuring point of 180 seconds. In contrast, the three bulk fill resin composites showed higher volumetric change than the other resin composites. The findings from this study provide clinicians with valuable information regarding the mechanical properties and

  17. Bonding of glass ceramic and indirect composite to non-aged and aged resin composite.

    Science.gov (United States)

    Gresnigt, Marco; Özcan, Mutlu; Muis, Maarten; Kalk, Warner

    2012-02-01

    Since adhesion of the restorative materials to pre-polymerized or aged resin composites presents a challenge to the clinicians, existing restorations are often removed and remade prior to cementation of fixed dental prostheses (FDPs). This study evaluated bond strength of non-aged and aged resin composite to an indirect resin composite and pressed glass ceramic using two resin cements. Disk-shaped specimens (diameter: 3.5, thickness: 3 mm) (N = 160) produced from a microhybrid resin composite (Quadrant Anterior Shine) were randomly divided into eight groups. While half of the specimens were kept dry at 37°C for 24 h, the other half was aged by means of thermocycling (6000 times, 5°C to 55°C). The non-aged and aged resin composites were bonded to a highly filled indirect composite (Estenia) and a pressed glass ceramic (IPS Empress II) using either a photopolymerizing (Variolink Veneer) or a dual-polymerizing (Panavia F2.0) resin cement. While cementation surfaces of both the direct and indirect composite materials were silica coated (30 µm SiO2, CoJet-Sand) and silanized (ESPE-Sil), ceramic surfaces were conditioned with hydrofluoric acid (20 s), neutralized, and silanized prior to cementation. All specimens were cemented under a load of 750 g. Shear force was applied to the adhesive interface in a universal testing machine (1 mm/min). Failure types of the specimens were identified after debonding. Significant effects of aging (p ceramic in combination with both cements showed no significant difference (p > 0.05). Both indirect composite (24.3 ± 5.1 MPa) and glass ceramic in combination with Variolink (22 ± 9 MPa) showed the highest results on non-aged composites, but were not significantly different from one another (p > 0.05). On the aged composites, indirect composite and glass ceramic showed no significant difference in bond strength within each material group (p > 0.05), with both Panavia (17.2 ± 6 and 15 ± 5.5 MPa, respectively) and Variolink (19 ± 8

  18. Alternative methods for determining shrinkage in restorative resin composites.

    Science.gov (United States)

    de Melo Monteiro, Gabriela Queiroz; Montes, Marcos Antonio Japiassú Resende; Rolim, Tiago Vieira; de Oliveira Mota, Cláudia Cristina Brainer; de Barros Correia Kyotoku, Bernardo; Gomes, Anderson Stevens Leônidas; de Freitas, Anderson Zanardi

    2011-08-01

    The purpose of this study was to evaluate polymerization shrinkage of resin composites using a coordinate measuring machine, optical coherence tomography and a more widely known method, such as Archimedes Principle. Two null hypothesis were tested: (1) there are no differences between the materials tested; (2) there are no differences between the methods used for polymerization shrinkage measurements. Polymerization shrinkage of seven resin-based dental composites (Filtek Z250™, Filtek Z350™, Filtek P90™/3M ESPE, Esthet-X™, TPH Spectrum™/Dentsply 4 Seasons™, Tetric Ceram™/Ivoclar-Vivadent) was measured. For coordinate measuring machine measurements, composites were applied to a cylindrical Teflon mold (7 mm × 2 mm), polymerized and removed from the mold. The difference between the volume of the mold and the volume of the specimen was calculated as a percentage. Optical coherence tomography was also used for linear shrinkage evaluations. The thickness of the specimens was measured before and after photoactivation. Polymerization shrinkage was also measured using Archimedes Principle of buoyancy (n=5). Statistical analysis of the data was performed with ANOVA and the Games-Howell test. The results show that polymerization shrinkage values vary with the method used. Despite numerical differences the ranking of the resins was very similar with Filtek P90 presenting the lowest shrinkage values. Because of the variations in the results, reported values could only be used to compare materials within the same method. However, it is possible rank composites for polymerization shrinkage and to relate these data from different test methods. Independently of the method used, reduced polymerization shrinkage was found for silorane resin-based composite. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  19. Fluorinated Alkyl Ether Epoxy Resin Compositions and Applications Thereof

    Science.gov (United States)

    Wohl, Christopher J. (Inventor); Connell, John W. (Inventor); Smith, Joseph G. (Inventor); Siochi, Emilie J. (Inventor); Gardner, John M. (Inventor); Palmieri, Frank M. (Inventor)

    2017-01-01

    Epoxy resin compositions prepared using amino terminated fluoro alkyl ethers. The epoxy resin compositions exhibit low surface adhesion properties making them useful as coatings, paints, moldings, adhesives, and fiber reinforced composites.

  20. The mechanical properties of nanofilled resin-based composites: characterizing discrete filler particles and agglomerates using a micromanipulation technique.

    LENUS (Irish Health Repository)

    Curtis, Andrew R

    2009-02-01

    To assess the mechanical properties of discrete filler particles representative of several inorganic fillers in modern dental resin-based composites (RBCs) and to assess the validity of a novel micromanipulation technique.

  1. Radiopacity of 28 Composite Resins for Teeth Restorations.

    Science.gov (United States)

    Raitz, Ricardo; Moruzzi, Patrizia Dubinskas; Vieira, Glauco; Fenyo-Pereira, Marlene

    2016-02-01

    Radiopacity is a fundamental requisite to check marginal adaptation of restorations. Our objective was to assess the radiopacity of 28 brands of light-cured composite resins and compare their radiopacity with that of enamel, dentin, and aluminum of equivalent thickness. Composite resin disks (0.2, 0.5, and 1 mm) were radiographed by the digital method, together with an aluminum penetrometer and a human tooth equivalent tooth section. The degree of radiopacity of each image was quantified using digital image processing. Wilcoxon nonparametric test was used for comparison of the mean thickness of each material. All of the materials tested had an equal or greater radiopacity than that of aluminum of equivalent thickness. Similar results for enamel were found with the exception of Durafill, which was less radiopaque than enamel (p composite resins comply with specification #27 of the American Dental Association. The radiopacity of Amelogen Plus, Aph, Brilhiante, Charisma, Concept Advanced, Evolux X, Exthet X, Inten S, Llis, Master Fill, Natural Look, Opallis, P60, Tetric, Tph, Z100, and Z250 was significantly higher than that of enamel (p composites, it is possible to observe the boundaries between restoration and tooth structure, thus allowing clinicians to establish the presence of microleakage or restoration gap. Suitable radiopacity is an essential requisite for good-quality esthetic restorative materials. We demonstrate that only some composites have the sufficient radiopacity to observe the boundaries between restoration and tooth structure, which is the main cause of restoration failure.

  2. Restoration of traumatized teeth with resin composites

    DEFF Research Database (Denmark)

    Pallesen, Ulla; van Dijken, Jan WV

    2018-01-01

    For a long time, the primary choice for initial restoration of a crown-fractured front tooth has been resin composite material. The restoration can in most cases be performed immediately after injury if there is no sign of periodontal injury. The method’s adhesive character is conservative to tooth......-structure and with minimal risk of pulpal complication. In addition, it offers an aesthetic solution to the patient immediately after an injury, which may bring a little comfort in a sad situation. The resin composite build-up is often changed or repaired a couple of times, before the tooth is restored with a porcelain...... present an aesthetic problem due to exposure of un-aesthetic crown-margins. The invasive permanent crown restorations are therefore often not suc-cessful on a long-term scale. On the other hand, a conservative direct restoration of an extensively fractured incisor crown with resin composite may...

  3. Factors influencing Saudi dental students′ preference of amalgam or composite for posterior dental restorations

    Directory of Open Access Journals (Sweden)

    Sharat Chandra Pani

    2014-01-01

    Conclusion: The findings of our study suggest that dental students in the Kingdom of Saudi Arabia seem to possess the ability to work confidently with posterior composite resins and seem to be comfortable in doing so; however, there is a significant difference in the factors influencing their choice of material.

  4. Composite resin fillings and inlays: An 11-year evaluation

    DEFF Research Database (Denmark)

    Pallesen, U.; Qvist, V.

    2003-01-01

    Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth......Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth...

  5. Novel self-healing dental resin with microcapsules of polymerizable triethylene glycol dimethacrylate and N,N-dihydroxyethyl-p-toluidine.

    Science.gov (United States)

    Wu, Junling; Weir, Michael D; Zhang, Qiang; Zhou, Chuanjian; Melo, Mary Anne S; Xu, Hockin H K

    2016-02-01

    Bulk fracture is one of the primary reasons for resin-based dental restoration failures. To date, there has been no report on the use of polymerizable dental monomers with acceptable biocompatibility to develop a resin with substantial self-healing capability. The objectives of this study were to: (1) develop a self-healing resin containing microcapsules with triethylene glycol dimethacrylate (TEGDMA)-N,N-dihydroxyethyl-p-toluidine (DHEPT) healing liquid in poly(urea-formaldehyde) (PUF) shells for the first time, and (2) determine the physical and mechanical properties, self-healing efficiency, and fibroblast cytotoxicity. Microcapsules of polymerizable TEGDMA-DHEPT in PUF were prepared via an in situ polymerization method. Microcapsules were added into a BisGMA-TEGDMA resin at microcapsule mass fractions of 0%, 5%, 10%, 15% and 20%. A flexural test was used to measure composite strength and elastic modulus. A single edge V-notched beam method was used to measure fracture toughness KIC and self-healing efficiency. Flexural strength and elastic modulus (mean±sd; n=6) of resin containing 5-15% microcapsules were similar to control without microcapsules (p>0.1). Adding microcapsules into the resin increased the virgin KIC, which was about 40% higher at 15% microcapsules than that with 0% microcapsules (pmicrocapsules. All specimens with 0-20% microcapsules had fibroblast viability similar to control without resin eluents (p>0.1). Self-healing dental resin containing microcapsules with polymerizable TEGDMA-DHEPT healing liquid in PUF shells were prepared for the first time with excellent self-healing capability. These microcapsules and self-healing resins containing them may be promising for dental restorations to heal cracks/damage and increase durability. Copyright © 2015 Academy of Dental Materials. All rights reserved.

  6. Extended Resin Composite Restorations: Techniques and Procedures

    NARCIS (Netherlands)

    Loomans, B.A.C.; Hilton, T.

    2016-01-01

    This article gives an overview of the state of the art of different restorative treatment procedures and techniques needed for placing extended posterior resin composite restorations. Clinical aspects related to the procedure are discussed and reviewed based on the current literature, such as the

  7. Composite fabrication via resin transfer molding technology

    Energy Technology Data Exchange (ETDEWEB)

    Jamison, G.M.; Domeier, L.A.

    1996-04-01

    The IMPReS (Integrated Modeling and Processing of Resin-based Structures) Program was funded in FY95 to consolidate, evaluate and enhance Sandia`s capabilities in the design and fabrication of composite structures. A key driver of this and related programs was the need for more agile product development processes and for model based design and fabrication tools across all of Sandia`s material technologies. A team of polymer, composite and modeling personnel was assembled to benchmark Sandia`s existing expertise in this area relative to industrial and academic programs and to initiate the tasks required to meet Sandia`s future needs. RTM (Resin Transfer Molding) was selected as the focus composite fabrication technology due to its versatility and growing use in industry. Modeling efforts focused on the prediction of composite mechanical properties and failure/damage mechanisms and also on the uncured resin flow processes typical of RTM. Appropriate molds and test composites were fabricated and model validation studies begun. This report summarizes and archives the modeling and fabrication studies carried out under IMPReS and evaluates the status of composite technology within Sandia. It should provide a complete and convenient baseline for future composite technology efforts within Sandia.

  8. Inhibition of odontogenic differentiation of human dental pulp cells by dental resin monomers.

    Science.gov (United States)

    Kwon, Ji Hyun; Park, Hee Chul; Zhu, Tingting; Yang, Hyeong-Cheol

    2015-01-01

    Dental resin monomers that are leached from the resin matrix due to incomplete polymerization can affect the viability and various functions of oral tissues and cells. In this study, the effects of triethylene glycol dimethacrylate (TEGDMA) and 2-hydroxyethyl methacrylate (HEMA) on odontogenic differentiation of human dental pulp cells (HDPCs) were examined. To mimic clinical situations, dental pulp cells were treated with resin monomers for 24 h prior to the analysis of alkaline phosphatase (ALP) activity and mRNA expression of genes related to pulp cell differentiation. To elucidate the underlying signaling pathways, regulation of mitogen-activated protein (MAP) kinases by resin monomers was also investigated. The ALP activity of HDPCs was reduced by TEGDMA and HEMA at noncytotoxic concentrations. The mRNA expression of dentin sialophosphoprotein (DSPP), osteocalcin (OCN), and osteopontin (OPN) was also downregulated by resin monomers. However, DSPP expression was not affected by hydrogen peroxide (H2O2). Among the MAP kinases examined, ERK activation (ERK phosphorylation) was not affected by either resin monomers or H2O2, whereas JNK was phosphorylated by TEGDMA and HEMA. Phospho-p38 was upregulated by HEMA, while TEGDMA and H2O2 suppressed p38 phosphorylation. Exposure to TEGDMA and HEMA for a limited period suppresses differentiation of HDPCs via different signaling pathways.

  9. [A new machinability test machine and the machinability of composite resins for core built-up].

    Science.gov (United States)

    Iwasaki, N

    2001-06-01

    A new machinability test machine especially for dental materials was contrived. The purpose of this study was to evaluate the effects of grinding conditions on machinability of core built-up resins using this machine, and to confirm the relationship between machinability and other properties of composite resins. The experimental machinability test machine consisted of a dental air-turbine handpiece, a control weight unit, a driving unit of the stage fixing the test specimen, and so on. The machinability was evaluated as the change in volume after grinding using a diamond point. Five kinds of core built-up resins and human teeth were used in this study. The machinabilities of these composite resins increased with an increasing load during grinding, and decreased with repeated grinding. There was no obvious correlation between the machinability and Vickers' hardness; however, a negative correlation was observed between machinability and scratch width.

  10. New bismaleimide matrix resins for graphite fiber composites

    Science.gov (United States)

    Hsu, M.-T. S.; Chen, T. S.; Parker, J. A.; Heimbuch, A. H.

    1985-01-01

    Two new bismaleimide resins based on the N,N'-m-phenylene-bis(m-amino-benzamide) structure have been synthesized and characterized. The mixtures of the two resins gave better handling, processing, mechanical, and thermal properties in graphite composites than did the individual resins. The mechanical strength of the cured graphite composites prepared from the 1:1 copolymer of the two bismaleimide resins was excellent at both ambient and elevated temperatures. The physical and mechanical properties of the composites from the new bismaleimide matrix resin systems are compared with conventional composites based on epoxy and other bismaleimide systems. The copolymer system provides another method for improving bismaleimide resins.

  11. Color change of composite resins subjected to accelerated artificial aging.

    Science.gov (United States)

    Tornavoi, Denise Cremonezzi; Agnelli, José Augusto Marcondes; Panzeri, Heitor; Dos Reis, Andréa Cândido

    2013-01-01

    The aim of this study was to evaluate the influence of accelerated artificial aging (AAA) on the color change of composite resins used in dentistry. Three composite resins were evaluated: Two microhybrids and one hybrid of higher viscosity, with different amounts and sizes of filler particles, shades C2 and B2. A total of 54 specimens were obtained (18 for each composite resin), made of a Teflon matrix (15 mm in diameter and 2 mm in height). The color measurements were obtained with a Spectrophotometer, (PCB 6807 BYK Gardner) before and after AAA. Data were submitted to the Kolmogorov-Smirnov test (α >0.05), ANOVA and Tukey test (α composite resins with the same shades was analyzed. All composite resins showed unacceptable color changes after AAA (ΔE > 3). Considering the variable ∆E, it was observed that the color tone C2 was already statistically different for the microhybrid composite resin prior to AAA (P composite resins (P composite resin group, before aging the composite resin hybrid of higher viscosity B2 showed the highest color variation rate and microhybrid with zirconium/silica C2 showed the lowest. All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2) and after (B2). It was also observed color difference within a group of the same composite resin and same hue.

  12. Color change of composite resins subjected to accelerated artificial aging

    Directory of Open Access Journals (Sweden)

    Denise Cremonezzi Tornavoi

    2013-01-01

    Conclusions: All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2 and after (B2. It was also observed color difference within a group of the same composite resin and same hue.

  13. Vickers microhardness comparison of 4 composite resins with different types of filler.

    Directory of Open Access Journals (Sweden)

    René García-Contreras

    2015-10-01

    Full Text Available Composite resins are the material of choice to restore minimal invasive cavities; conversely, it is important to explore the mechanical properties of commercially available dental materials. Objective: To compare the Vickers microhardness (VHN of four available commercial composite resins using standardized samples and methods. Methodology: Composite cylinders were manufactured in a Teflon mould. We used the follow composite resins (n=4/gp: Microhybrid resins [Feeling Lux (Viarden and Amelogen Plus (Ultradent], Hybrid resin [Te-Econom Plus (Ivoclar] and Nanohybrid resin [Filtek Z350 (3M ESPE]. All samples were incubated in distilled water at 37ºC for five days. The test was carried out with microhardness indenter at 10 N, and a dwelling time of 10 s for 9 indentations across the specimens resulting in a total of 36 indentations for each group. Data were subjected to Kolmogorov-Smirnov normality test and ANOVA (post-hoc Tukey test. Results: The VHN mean values ranged from harder to softer as follows: Filtek Z350 (71.96±6.44 (p Amelogen Plus (59.90±4.40 (p Feeling lux (53.52±5.72> Te-Econom Plus (53.26±5.19. Conclusion: According to our results, the microhardness of the evaluated conventional composite resins can withstand the masticatory forces; however nanohybrid composite resins showed better Vickers microhardness and therefore are a more clinically suitable option for minimal invasion treatments.

  14. Anterior makeover on fractured teeth by simple composite resin restoration

    Directory of Open Access Journals (Sweden)

    Eric Priyo Prasetyo

    2011-09-01

    Full Text Available Background: In daily practice dentists usually treat tooth fractures with more invasive treatments such as crown, veneer and bridges which preparation require more tooth structure removal. While currently there is trend toward minimal invasive dentistry which conserves more tooth structure. This is enhanced with the vast supply of dental materials and equipment in the market, including restorative materials. Provided with these supporting materials and equipment and greater patient’s demand for esthetic treatment, dentists must aware of the esthetics and basic principle of conserving tooth which should retain tooth longevity. Purpose: This article showed that a simple and less invasive composite resin restoration can successfully restore anterior esthetic and function of fractured teeth which generally treated with more invasive treatment options. Case: A 19 year-old female patient came with fracture on 21 and 22. This patient had a previous history of dental trauma about nine years before and was brought to a local dentist for debridement and was given analgesic, the involved teeth were not given any restorative treatment. Case management: The fractured 21 and 22 were conventionally restored with simple composite resin restoration. Conclusion: Fracture anterior teeth would certainly disturbs patient’s appearance, but these teeth could be managed conservatively and economically by simple composite resin restoration.Latar belakang: Dalam praktek sehari-hari pada umumnya dokter gigi merawat fraktur dengan restorasi invasif seperti mahkota, veneer dan jembatan yang semuanya memerlukan pengambilan jaringan gigi lebih banyak, sedangkan saat ini trend perawatan gigi lebih menuju kearah invasif minimal yang mempertahankan jaringan gigi sebanyak mungkin. Keadaan ini ditunjang oleh tersedianya berbagai macam bahan dan peralatan kedokteran gigi di pasaran, termasuk bahan restorasi. Dengan tersedianya bahan dan peralatan yang mendukung serta tingginya

  15. Variations in survival time for amalgam and resin composite restorations: a population based cohort analysis.

    Science.gov (United States)

    Birch, S; Price, R; Andreou, P; Jones, G; Portolesi, A

    2016-09-01

    To estimate the association between the restorative material used and time to further treatment across population cohorts with universal coverage for dental treatment. Cohort study of variation in survival time for tooth restorations over time and by restoration material used based on an Accelerated Failure Time model. Primary dental care clinics. Members of Canada's First Nations and Inuit population covered by the Non-Insured Health Benefits program of Health Canada for the period April 1, 1999 to March 31, 2012. Tooth restorations using resin composite or amalgam material. Survival time of restoration to further treatment. Median survival time for resin composite was 51 days longer than amalgam, for restorations placed in 1999-2000. This difference was not statistically significant (p⟩0.05). Median survival times were lower for females, older subjects. Those visiting the dentist annually, and decreased monotonically over time from 11.2 and 11.3 years for resin composite and amalgam restorations respectively placed in 1999-2000 to 6.9 and 7.0 years for those placed in 2009-10. Resin composite restorations performed no better than amalgams over the study period, but cost considerably more. With the combination of the overall decrease in survival times for both resin composite and amalgam restorations and the increase in use of resin composite, the costs of serving Health Canada's Non-Insured Health Benefits population will rise considerably, even without any increase in the incidence of caries. Copyright© 2016 Dennis Barber Ltd

  16. A comparative study to determine strength of autopolymerizing acrylic resin and autopolymerizing composite resin influenced by temperature during polymerization: An In Vitro study

    Directory of Open Access Journals (Sweden)

    Anuj Chhabra

    2017-01-01

    Full Text Available Aim: Temporary coverage of a prepared tooth is an important step during various stages of the fixed dental prosthesis. Provisional restorations should satisfy proper mechanical requirements to resist functional and nonfunctional loads. A few studies are carried out regarding the comparison of the effect of curing environment, air and water, on mechanical properties of autopolymerizing acrylic and composite resin. Hence, the aim of this study was to compare the transverse strength of autopolymerizing acrylic resin and autopolymerizing composite resin as influenced by the temperature of air and water during polymerization. Materials and Methods: Samples of autopolymerizing acrylic resin and composite resin were prepared by mixing as per manufacturer's instructions and were placed in a preformed stainless steel mold. The mold containing the material was placed under different controlled conditions of water temperature and air at room temperature. Polymerized samples were then tested for transverse strength using an Instron universal testing machine. Results: Alteration of curing condition during polymerization revealed a significant effect on the transverse strength. The transverse strength of acrylic resin specimens cured at 60°C and composite resin specimens cured at 80°C was highest. Polymerizing the resin in cold water at 10°C reduced the mechanical strength. Conclusions: Polymerization of the resin in hot water greatly increased its mechanical properties. The method of placing resin restoration in hot water during polymerization may be useful for improving the mechanical requirements and obtaining long-lasting performance.

  17. Effect of proximal box elevation with resin composite on marginal quality of resin composite inlays in vitro.

    Science.gov (United States)

    Roggendorf, Matthias J; Krämer, Norbert; Dippold, Christoph; Vosen, Vera E; Naumann, Michael; Jablonski-Momeni, Anahita; Frankenberger, Roland

    2012-12-01

    To evaluate marginal quality and resin-resin transition of lab made resin composite inlays in deep proximal cavities with and without 3 mm proximal box elevation (PBE) using resin composites before and after thermo-mechanical loading (TML). MOD cavities with one proximal box beneath the cementoenamel junction were prepared in 40 extracted human third molars. Proximal boxes ending in dentine were elevated 3 mm with different resin composites (G-Cem, Maxcem Elite as self-adhesive resin cements and Clearfil Majesty Posterior as restorative resin composite in one or three layers bonded with AdheSE), or left untreated. Clearfil Majesty Posterior inlays were luted with Syntac and Variolink II (n = 8). Marginal quality as well as the PBE-composite inlay interface was analyzed under an SEM using epoxy resin replicas before and after thermomechanical loading (100,000 × 50 N and 2500 thermocylces between +5 °C and +55 °C). Bonding resin composite inlays directly to dentine showed similar amounts of gap-free margins in dentine compared to PBE applied in three consecutive layers (p > 0.05). The groups with self-adhesive resin cements for PBE exhibited significantly more gaps in dentine (p < 0.05). With layered resin composite, PBE is effective in indirect resin composite bonding to deep proximal boxes. Self-adhesive resin cements are not suitable for this indication. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. A conservative treatment approach using direct composite resins for anterior teeth eroded by lemon sucking.

    Science.gov (United States)

    Passos, Vanara Florencio; de Souza, Andre Mattos Brito; Rodrigues, Lidiany Karla Azevedo; Bombonatti, Juliana Campos Fraga Soares; Santiago, Sergio Lima

    2013-08-01

    An excessively acidic diet results in the progressive deterioration of dental health, with functional, esthetic, and biological consequences. Previously, rehabilitation required placing numerous full crowns and root canal treatments; however, with improved adhesive techniques, a more conservative approach may be utilized to preserve tooth structure. This article describes 2 cases that utilized conservative dental treatments (involving direct composite resins with minimal preparation of the tooth structure) to treat eroded dentition induced by lemon sucking.

  19. Effects of toothbrush hardness on in vitro wear and roughness of composite resins.

    Science.gov (United States)

    Kyoizumi, Hideaki; Yamada, Junji; Suzuki, Toshimitsu; Kanehira, Masafumi; Finger, Werner J; Sasaki, Keiichi

    2013-11-01

    To investigate and compare the effects of toothbrushes with different hardness on abrasion and surface roughness of composite resins. Toothbrushes (DENT. EX Slimhead II 33, Lion Dental Products Co. Ltd., Tokyo, Japan) marked as soft, medium and hard, were used to brush 10 beam-shaped specimens of each of three composites resins (Venus [VEN], Venus Diamond [VED] and Venus Pearl [VEP]; HeraeusKulzer) with standardized calcium carbonate slurry in a multistation testing machine (2N load, 60 Hz). After each of five cycles with 10k brushing strokes the wear depth and surface roughness of the specimens were determined. After completion of 50k strokes representative samples were inspected by SEM. Data were treated with ANOVA and regression analyses (p composite resins increased linearly with increasing number of brushing cycles (r² > 0.9). Highest wear was recorded for VEN, lowest for VED. Hard brushes produced significantly higher wear on VEN and VEP, whereas no difference in wear by toothbrush type was detected for VED. Significantly highest surface roughness was found on VED specimens (Ra > 1.5 µm), the lowest one on VEN (Ra composite resins produced by toothbrushing with dentifrice depend mainly on the type of restorative resin. Hardness grades of toothbrushes have minor effects only on abrasion and surface roughness of composite resins. No relationship was found between abrasion and surface roughness. The grade of the toothbrush used has minor effect on wear, texture and roughness of the composite resin.

  20. A 24-month evaluation of amalgam and resin-based composite restorations

    DEFF Research Database (Denmark)

    McCracken, Michael S; Gordan, Valeria V; Litaker, Mark S

    2013-01-01

    Knowing which factors influence restoration longevity can help clinicians make sound treatment decisions. The authors analyzed data from The National Dental Practice-Based Research Network to identify predictors of early failures of amalgam and resin-based composite (RBC) restorations....

  1. Contact angle and surface free energy of experimental resin-based dental restorative materials after chewing simulation.

    Science.gov (United States)

    Rüttermann, Stefan; Beikler, Thomas; Janda, Ralf

    2014-06-01

    To investigate contact angle and surface free energy of experimental dental resin composites containing novel delivery systems of polymeric hollow beads and low-surface tension agents after chewing simulation test. A delivery system of novel polymeric hollow beads differently loaded with two low-surface tension agents was used in different amounts to modify commonly formulated experimental dental resin composites. The non-modified resin was used as standard. Surface roughness Ra, contact angle Θ, total surface free energy γS, its apolar γS(LW), polar γS(AB), Lewis acid γS(+) and base γS(-) terms were determined and the results prior to and after chewing simulation test were compared. Significance was phollow beads highly loaded with low-surface tension agents were found to significantly increase contact angle and thus to reduce surface free energy of experimental dental resin composites prior to and after chewing simulation test. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  2. BisGMA/TEGDMA dental composite containing high aspect-ratio hydroxyapatite nanofibers

    Science.gov (United States)

    Chen, Liang; Yu, Qingsong; Wang, Yong; Li, Hao

    2011-01-01

    Objectives The objectives of this study are to investigate the properties of high aspect-ratio hydroxyapatite (HAP) nanofibers and the reinforcing effect of such fibers on bisphenol A glycidyl methacrylate (BisGMA)/triethylene glycol dimethacrylate (TEGDMA) dental resins (without silica microparticle filler) and dental composites (with silica microparticle filler) with various mass fractions (loading rates). Methods HAP nanofibers were synthesized using a wet-chemical method and characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and thermal gravimetric analysis (TGA). Biaxial flexural strength (BFS) of the HAP nanofibers reinforced dental resins without any microsized filler and dental composites with silica microparticle filler was tested and analysis of variance (ANOVA) was used for the statistically analysis of acquired data. The morphology of fracture surface of tested dental composite samples was examined by SEM. Results The HAP nanofibers with aspect-ratios of 600 to 800 can be successfully fabricated with a simple wet-chemical method in aqueous solution. Impregnation of small mass fractions of the HAP nanofibers (5 wt% or 10 wt%) into the BisGMA/TEGDMA dental resins or impregnation of small mass fractions of the HAP nanofibers (2 wt% or 3 wt%) into the dental composites can substantially improve the biaxial flexural strength of the resulting dental resins and composites. A percolation threshold of HAP nanofibers, beyond which more nanofibers will no longer further increase the mechanical properties of dental composites containing HAP nanofibers, was observed for the dental composites with or without silica microparticle filler. Our mechanical testing and fractographic analysis indicated that the relatively good dispersion of HAP nanofibers at low mass fraction is the key reason for the significantly improved biaxial flexural strength, while higher mass fraction of HAP nanofibers tends to lead to bundles that cannot effectively

  3. Physical Property Investigation of Two Recently Marketed Resin Composite Restorative Materials

    Science.gov (United States)

    2015-06-18

    Huysmans  MCDNJM.  12-­‐year   Survival  of   Composite  vs.   Amalgam  Restorations.  J  Dent  Res  2010;  89:1063-­‐   1067...Marketed Resin Composite Restorative Materials 7. Intended publication/meeting: International Association of Dental Research Annual Meeting 8...Marketed Resin Composite Restorative Materials Major Marcus P. Kropf APPROVED; Colo71 Howard W. Roberts Date APPROVED: Col Drew W. Fallis Dean, Air

  4. Fracture Resistance of Endodontically Treated Teeth Restored with Biodentine, Resin Modified GIC and Hybrid Composite Resin as a Core Material.

    Science.gov (United States)

    Subash, Dayalan; Shoba, Krishnamma; Aman, Shibu; Bharkavi, Srinivasan Kumar Indu; Nimmi, Vijayan; Abhilash, Radhakrishnan

    2017-09-01

    The restoration of a severely damaged tooth usually needs a post and core as a part of treatment procedure to provide a corono - radicular stabilization. Biodentine is a class of dental material which possess high mechanical properties with excellent biocompatibility and bioactive behaviour. The sealing ability coupled with optimum physical properties could make Biodentine an excellent option as a core material. The aim of the study was to determine the fracture resistance of Biodentine as a core material in comparison with resin modified glass ionomer and composite resin. Freshly extracted 30 human permanent maxillary central incisors were selected. After endodontic treatment followed by post space preparation and luting of Glass fibre post (Reforpost, Angelus), the samples were divided in to three groups based on the type of core material. The core build-up used in Group I was Biodentine (Septodont, France), Group II was Resin-Modified Glass Ionomer Cement (GC, Japan) and Group III was Hybrid Composite Resin (TeEconom plus, Ivoclar vivadent). The specimens were subjected to fracture toughness using Universal testing machine (1474, Zwick/Roell, Germany) and results were compared using One-way analysis of variance with Tukey's Post hoc test. The results showed that there was significant difference between groups in terms of fracture load. Also, composite resin exhibited highest mean fracture load (1039.9 N), whereas teeth restored with Biodentine demonstrated the lowest mean fracture load (176.66 N). Resin modified glass ionomer exhibited intermediate fracture load (612.07 N). The primary mode of failure in Group I and Group II was favourable (100%) while unfavourable fracture was seen in Group III (30%). Biodentine, does not satisfy the requirements to be used as an ideal core material. The uses of RMGIC's as a core build-up material should be limited to non-stress bearing areas. Composite resin is still the best core build-up material owing to its high fracture

  5. Effectiveness of composite resin polymerization using light-emitting diodes (LEDs) or halogen-based light-curing units

    OpenAIRE

    Micali,Bianca; Basting,Roberta Tarkany

    2004-01-01

    The clinical performance of composite resins is greatly influenced by the quality of the light-curing unit used. The aim of this study was to compare the efficiency of a commercial light-emitting diode (LED) with that of a halogen-based light-curing unit by means of dye penetration of a micro hybrid composite resin. The composite resin evaluated was Filtek Z250 (3M Dental). The composite was filled into acrylic moulds that were randomly polymerized for 40 seconds by each of the light-emitting...

  6. Mechanical and antibacterial properties of benzothiazole-based dental resin materials.

    Science.gov (United States)

    Zhu, Wenbin; Lao, Chonghui; Luo, Shuzhen; Liu, Fang; Huang, Qiting; He, Jingwei; Lin, Zhengmei

    2018-04-01

    A synthesized benzothiazole containing mono-methacrylate monomer BTTMA was incorporated into Bis-GMA/TEGDMA dental resin system with a series of mass concentration from 5 to 30 wt.% as an antibacterial agent. The influence of BTTMA on physicochemical properties of dental resin system, such as double bond conversion (DC), volumetric shrinkage (VS), flexural strength (FS) and modulus (FM), water sorption (WS) and solubility (SL) were investigated. Direct contact testing and agar diffusion testing were used to evaluate the antibacterial activity of BTTMA containing dental resin. The results showed that BTTMA could endow dental resin with significant antibacterial activity when its concentration reached a certain amount (20 wt.%), and the antibacterial activity of BTTMA containing dental resin was mainly attributed to the immobilized BTTMA instead of the unreacted leachable BTTMA. BTTMA had no negative effect on physicochemical properties of dental resin, and even some BTTMA containing dental resins had advantages like higher DC, lower VS and WS when compared with control resin. Therefore, BTTMA could be considered as a suitable antibacterial agent in dental material, but much more researches concerned about biocompatibility should be done in future to prove whether it could be applied in clinic.

  7. Effect of nano SiO{sub 2} particles on the morphology and mechanical properties of POSS nanocomposite dental resins

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yizhi; Sun, Yi, E-mail: sunyi@hit.edu.cn; Zeng, Fanlin [Harbin Institute of Technology, Department of Astronautic Science and Mechanics (China); Xie, Weili, E-mail: xwl811@126.com [Harbin Medical University, Department of Stomatology (China); Liu, Yang [Harbin Stomatology Hospital (China); Geng, Lin [Harbin Institute of Technology, School of Materials Science and Engineering (China)

    2014-12-15

    Nanocomposite dental resins composed of polyhedral oligomeric silsesquioxane nanocomposite matrix and 0, 0.5,1, 1.5 and 2 wt% nano SiO{sub 2} as filler were prepared by light curing method. The nanocomposite resins were characterized by performing compressive, three-point flexure, nanoindentation and nanoscratch testings as well as optical microscopy and scanning electron microscope analysis. The effects of different nano SiO{sub 2} contents were studied on compressive strength, flexural strength, hardness and resistance of composite resin. From the mechanical results, it was found that nano SiO{sub 2} effectively enhanced the mechanical properties of the composite resins at low content. With the increase of the nano SiO{sub 2} content, the mechanical properties decreased. It was attributed to the content of nano SiO{sub 2} and dispersion of nanoparticles in matrix.

  8. Effect of Layering Methods, Composite Type, and Flowable Liner on the Polymerization Shrinkage Stress of Light Cured Dental Composites

    Science.gov (United States)

    2011-08-01

    18 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS 1 Introduction Composite restoration has become an essential part of everyday dental ...thickness of flowable liner, use of RMGI (resin modified glass ionomer ) liner, and light curing methods on the cuspal deflection should be...polymerization shrinkage stress in polymer-based restoratives . J Dent, Vol. 25, pp 435-440, 1997. [4] J. Ferracane. Placing dental composites-A stressful

  9. Preparation and Evaluation of Dental Resin with Antibacterial and Radio-Opaque Functions

    Directory of Open Access Journals (Sweden)

    Pekka K. Vallittu

    2013-03-01

    Full Text Available In order to prepare antibacterial and radio-opaque dental resin, a methacrylate monomer named 2-Dimethyl-2-dodecyl-1-methacryloxyethyl ammonium iodine (DDMAI with both antibacterial and radio-opaque activities was added into a 2,2-bis[4-(2-hydroxy-3-methacryloyloxypropyl-phenyl]propane (Bis-GMA/methyl methacrylate (MMA dental resin system. Degree of conversion (DC, flexural strength (FS and modulus (FM, water sorption (WS and solubility (WSL, antibacterial activity, and radio-opacity (ROX of the obtained dental resin system were investigated. Bis-GMA/MMA resin system without DDMAI was used as a control. The results showed that DDMAI could endow BIS-GMA/MMA resin system with good antibacterial (p 0.05. However, incorporating DDMAI into Bis-GMA/MMA resin could reduce mechanical properties (p < 0.05 and increase WS and WSL (p < 0.05, thus further work is needed in order to optimize the resin formulation.

  10. Polymerisation efficiency and shrinkage effects in resin based dental restoratives

    Science.gov (United States)

    Al-Hindi, Abdusalam M.

    The aim of this study was to investigate the polymerisation efficiency and shrinkage effects in resin based dental restorative materials. The study highlights factors affecting the polymerisation efficiency, but the efficiency of the light curing units was first measured. The output light intensity and the temperature rise produced by two units were measured using a radiometer with a flat-response characteristic. The units were the Elipar Highlight (Espe Dental AG) and XL3000 (3M Co). The former unit has a dual-intensity mode of operation: 10 slow plus 30 s high (termed "soft-start") and a Ml-intensity mode: 40 s high. Its "high" intensity was significantly greater than the XL3000 Unit, and produced correspondingly greater temperature rises. One of the hypotheses to be tested was whether any useful network-conversion (polymerisation) was attained by application of the 10 slow-intensity phase of the "soft-start" mode. To address this question, the polymerisation efficiency of three representative resin-based restorative materials was studied by measuring depth-of-cure, exotherm, surface hardness and degree of conversion. The Elipar Unit was used principally m these studies, with four modes of radiation: "full" and "soft- start", as above, and either 10 s or 40 s of low intensity light. Most measurements were performed at 23°C, but some specimen groups were also pre-conditioned at 37°C. Depth-of-cure values obtained by "soft-start" were as great as with "full" radiation. Low- intensity irradiation alone gave significantly reduced, but non-zero cure-depths. The exotherm of the specimens cured by "soft-start" was lower than those cured by "full" light-intensity. This pattern was also apparent when the lower-intensity (XL3000) Unit was deployed. Surface hardness was measured on upper and lower surfaces of specimens radiated by different modes. The hardness was greater at upper, relative to lower surfaces with "full" intensity. The lower-surface hardness with low

  11. Comparison of Cashew Nut Shell Liquid (CNS Resin with Polyester Resin in Composite Development

    Directory of Open Access Journals (Sweden)

    C. C. Ugoamadi

    2013-12-01

    Full Text Available Natural resins can compete effectively with the synthetic ones in composite development. In this research, cashew nuts were picked and processed for the extraction of the resin content. The resin (natural resin so obtained was mixed with cobalt amine (accelerator, methyl ethyl ketone peroxide (catalyst to develop two sets of composite specimens – specimens without fibres and specimens reinforced with glass fibres. This method of sample specimen development was repeated with polyester (synthetic resin. Compressive and tensile strength tests conducted proved that composites developed with cashew nut shell liquid (CNSL resin were comparable to those developed with polyester resin. In the results, CNSL has an ultimate compressive strength of 55MPa compared to that of polyester resin with an ultimate strength of 68MPa. The result of tensile strength proved cashew nut shell liquid resin (with ultimate strength of 44MPa to be better than polyester resin with 39MPa as ultimate tensile strength. This means that natural resins could be a better substitute for the synthetic ones when the required quantities of fibers (reinforcements and fillers are used in the fibre-reinforced plastic composite developments.

  12. Versatile composite resins simplifying the practice of restorative dentistry.

    Science.gov (United States)

    Margeas, Robert

    2014-01-01

    After decades of technical development and refinement, composite resins continue to simplify the practice of restorative dentistry, offering clinicians versatility, predictability, and enhanced physical properties. With a wide range of products available today, composite resins are a reliable, conservative, multi-functional restorative material option. As manufacturers strive to improve such properties as compression strength, flexural strength, elastic modulus, coefficient of thermal expansion, water sorption, and wear resistance, several classification systems of composite resins have been developed.

  13. Prevalence of cusp fractures in teeth restored with amalgam and with resin-based composite.

    Science.gov (United States)

    Wahl, Michael J; Schmitt, Margaret M; Overton, Donald A; Gordon, M Kathleen

    2004-08-01

    Complete cusp fracture in restored teeth is a common problem observed in general dental practice. Many dentists believe that teeth restored with amalgam are more likely to be associated with cusp fractures than are those restored with resin-based composite. METHODS. The authors noted the condition of 10,869 posterior teeth with amalgam or resin-based composite restorations with at least one cusp present, unrestored or missing in 1,902 consecutively seen adult patients in a private general dental practice. For each patient, the authors recorded age, type of restorations, number of surfaces of each restoration, and presence or absence of a complete cusp fracture and of caries. There was a lower percentage of cusp fractures in younger subjects than in older subjects and in teeth with a single restored surface than in those with more than one restored surface. There was no significant difference in the prevalence of cusp fracture rates in amalgam-restored teeth versus composite-restored teeth in subjects aged 18 through 54 years. In subjects aged 55 through 96 years, there was a marginally significantly greater cusp fracture rate in composite-restored teeth than in those restored with amalgam. Overall, there was no significant difference in the prevalence of cusp fracture in teeth restored with amalgam (1.88 percent) versus composite-restored teeth (2.29 percent). The prevalence of cusp fractures in amalgam-restored teeth and resin-based composite-restored teeth is not significantly different. Teeth with more than one surface restored with either resin-based composite or amalgam and teeth in older subjects were more likely to suffer a cusp fracture. Teeth restored with amalgam and with resin-based composite exhibited equally low cusp fracture prevalence. When choosing between amalgam and resin-based composite in consideration of the likelihood of a future cusp fracture, either restorative material is acceptable.

  14. The Effect of Novel Mercapto Silane Systems on Resin Bond Strength to Dental Noble Metal Alloys.

    Science.gov (United States)

    Lee, Yangho; Kim, Kyo-Han; Kim, Young Kyung; Son, Jun Sik; Lee, Eunkyung; Kwon, Tae-Yub

    2015-07-01

    Self-assembled monolayers of thiols (RSH), which are key elements in nanoscience and nanotechnology, have been used to link a range of materials to planar gold surfaces or gold nanoparticles. In this study, the adhesive performance of mercapto silane systems to dental noble metal alloys was evaluated in vitro and compared with that of commercial dental primers. Dental gold-palladium-platinum (Au-Pd-Pt), gold-palladium-silver (Au-Pd-Ag), and palladium-silver (Pd-Ag) alloys were used as the bonding substrates after air-abrasion (sandblasting). One of the following primers was applied to each alloy: (1) no primer treatment (control), (2) three commer- cial primers: V-Primer, Metal Primer II, and M.L. Primer, and (3) two experimental silane primer systems: 2-step application with 3-mercaptopropyltrimethoxysilane (SPS) (1.0 wt%) and then 3-methacryloxypropyltrimethoxysilane (MPS) (1.0 wt%), and a silane blend consisting of SPS and MPS (both 1.0 wt%). Composite resin cylinders with a diameter of 2.38 mm were bonded to the surfaces and irradiated for 40 sec using a curing light. After storage in water at 37 °C for 24 h, all the bonded specimens were thermocycled 5000 times before the shear bond strength test. Regardless of the alloy type, the mercapto silane systems (both the 2-step and blend systems) consistently showed superior bonding performance than the commercial primers. Contact angle analysis of the primed surfaces indicated that higher resin bond strengths were produced on more hydrophilic alloy surfaces. These novel mercapto silane systems are a promising alternative for improving resin bonding to dental noble metal alloys.

  15. Color of bulk-fill composite resin restorative materials.

    Science.gov (United States)

    Barutcigil, Çağatay; Barutcigil, Kubilay; Özarslan, Mehmet Mustafa; Dündar, Ayşe; Yilmaz, Burak

    2017-09-28

    To evaluate the color stability of novel bulk-fill composite resins. Color measurements of a nanohybrid composite resin (Z550) and 3 bulk-fill composite resins (BLK, AFX, XTF; n = 45) were performed before polymerization. After polymerization, color measurements were repeated and specimens were immersed in distilled water or red wine, or coffee. Color change [CIEDE2000 (ΔE 00 )] was calculated after 24 h, 1 and 3 weeks. Data were analyzed with Kruskal-Wallis, Mann-Whitney U and Wilcoxon tests (α = 0.05). Color changes observed after polymerization were significant for all groups. Color changes observed in distilled water for Z550 and AFX were significant. Color changes after stored in red wine and coffee were significant for all groups. Bulk-fill composite resin color change increased over time for all groups in red wine and coffee (P composite resin and bulk-fill composite resins. AFX had the highest color change in distilled water. The color of tested bulk-fill composite resins significantly changed after immersion in beverages and over time. Color change observed with the nanohybrid composite resin after 1 week was stable. Clinicians should keep in mind that tested composite resins may change color when exposed to water and significantly change color immediately after they are polymerized. In addition, the color change continues over time should the patient is a coffee and/or red wine consumer. © 2017 Wiley Periodicals, Inc.

  16. Method for curing alkyd resin compositions by applying ionizing radiation

    International Nuclear Information System (INIS)

    Watanabe, T.; Murata, K.; Maruyama, T.

    1975-01-01

    An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

  17. Microhardness of resin composite materials light-cured through fiber reinforced composite.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Ray, N.J.; Creugers, N.H.J.; Kreulen, C.M.

    2009-01-01

    OBJECTIVES: To compare polymerization efficiency of resin composite basing materials when light-cured through resin composite and fiber reinforced composite (FRC) by testing microhardness. METHODS: Simulated indirect restorations were prepared by application of resin composite (Clearfil AP-X) or FRC

  18. Evaluation of Resin-Resin Interface in Direct Composite Restoration Repair

    Science.gov (United States)

    Stoleriu, S.; Andrian, S.; Pancu, G.; Nica, I.; Iovan, G.

    2017-06-01

    The aim of this study was to evaluate the resin-resin interface when a universal bonding agent was used in two different strategies in direct restoration repair. Two composite resins (a micro-filled hybrid and a nano-filled hybrid) as old restorations that have to be repair, a universal bonding agent and a micro-filled hybrid composite resin (different then that aged) as new material for repair were chosen for the study. Non-aged samples were used as control and aged samples were used as study groups. The universal bonding agent was applied in etch-and-rinse and in self-etch strategies. The interface between old and new composite resins was evaluated by SEM and the microleakage was assessed by scoring the dye penetration. Very good adaptation of the two different composite resins placed in direct contact in non-aged samples was recorded. No gaps or defects were visible and strong resin-resin contact was observed. After aging, enlargement of resin-resin junction were observed in most of the samples and a increased dye penetration was recorded irrespective of the strategy (etch-and-rinse or self-etch) used for bonding agent application.

  19. Characterization of Composite Fan Case Resins

    Science.gov (United States)

    Dvoracek, Charlene M.

    2004-01-01

    The majority of commercial turbine engines that power today s aircraft use a large fan driven by the engine core to generate thrust which dramatically increases the engine s efficiency. However, if one of these fan blades fails during flight, it becomes high energy shrapnel, potentially impacting the engine or puncturing the aircraft itself and thus risking the lives of passengers. To solve this problem, the fan case must be capable of containing a fan blade should it break off during flight. Currently, all commercial fan cases are made of either just a thick metal barrier or a thinner metal wall surrounded by Kevlar-an ultra strong fiber that elastically catches the blade. My summer 2004 project was to characterize the resins for a composite fan case that will be lighter and more efficient than the current metal. The composite fan case is created by braiding carbon fibers and injecting a polymer resin into the braid. The resin holds the fibers together, so at first using the strongest polymer appears to logically lead to the strongest fan case. Unfortunately, the stronger polymers are too viscous when melted. This makes the manufacturing process more difficult because the polymer does not flow as freely through the braid, and the final product is less dense. With all of this in mind, it is important to remember that the strength of the polymer is still imperative; the case must still contain blades with high impact energy. The research identified which polymer had the right balance of properties, including ease of fabrication, toughness, and ability to transfer the load to the carbon fibers. Resin deformation was studied to better understand the composite response during high speed impact. My role in this research was the testing of polymers using dynamic mechanical analysis and tensile, compression, and torsion testing. Dynamic mechanical analysis examines the response of materials under cyclic loading. Two techniques were used for dynamic mechanical analysis

  20. An in vitro quantitative antibacterial analysis of amalgam and composite resins.

    Science.gov (United States)

    Beyth, Nurit; Domb, Abraham J; Weiss, Ervin I

    2007-03-01

    Antibacterial properties of restorative dental materials such as amalgam and composite resins may improve the restorative treatment outcome. This study evaluates the antibacterial properties of three composite resins: Z250, Tetric Ceram, P60 and a dental amalgam in vitro. Streptococcus mutans and Actinomyces viscosus served as test microorganisms. Three quantitative microtiter spectrophotometric assays were used to evaluate the effect of the restorative materials on: (i) early-stage biofilm using a direct contact test (DCT); (ii) planktonic bacterial growth; (iii) bacterial growth in the materials' elute. For comparison purposes, agar diffusion test (ADT) was also performed. The effect of the composite resins on bacterial growth was minimal and limited to a few days only. One-week-aged composites promoted growth of S. mutans and A. viscosus. The antibacterial properties in direct contact were more potent than in planktonic bacterial growth. Amalgam showed complete inhibition of both bacteria in all phases, and the effect lasted for at least 1 week. The materials' elute had no effect on both bacterial growth with the exception of complete inhibition of S. mutans in amalgam. The later results correlated with the ADT. The present findings demonstrate potent and lasting antibacterial properties of amalgam, which are lacking in composite resins. This may explain the clinical observation of biofilm accumulated more on composites compared to amalgams. It follows that the assessment of antibacterial properties of poorly-soluble materials has to employ more than one assay.

  1. Synthesis of none Bisphenol A structure dimethacrylate monomer and characterization for dental composite applications.

    Science.gov (United States)

    Liang, Xiaoxu; Liu, Fang; He, Jingwei

    2014-08-01

    In this study, new dimethacrylate monomer SiMA without Bisphenol A (BPA) structure was synthesized and used as base resin of dental composite materials with the aim of reducing human exposure to BPA derivatives. SiMA was synthesized through ring-opening addition reaction between 1,3-bis[2(3,4-epoxycyclohex-1-yl)ethyl]tetra-methyldisiloxane and methacrylic acid, and its structure was confirmed by FT-IR and (1)H NMR spectra. SiMA was mixed with TEGDMA (50/50, wt/wt) and photoinitiation system (0.7 wt% of CQ and 0.7 wt% of DMAEMA) to form resin system. Experimental composite EC was then prepared by SiMA based resin loading with BaAlSiO2 microfillers (72wt%). Double bond conversion (DC) was determined by FT-IR analysis. Volume shrinkage (VS) was measured through variation of density before and after irradiation. Water sorption (WS) and solubility (SL) were obtained until the mass variation of polymer in distilled water kept stable. Flexural strength (FS) and modulus (FM) of the polymer were measured using a three-point bending set up. Extract of composite was used to evaluate its cytotoxic effect on humane dental pulp cells, and relative growth rate (RGR) was obtained by CCK-8 assay. Bis-GMA/TEGDMA (50/50, wt/wt) resin system and universal dental restorative materials 3M ESPE Filtek™ Z250 were used as references for neat resin system and composite material, respectively. FT-IR and (1)H NMR spectra showed that structure of SiMA was the same as designed. For the neat resin systems: DC of SiMA based resin was higher than that of Bis-GMA based resin (p0.05); FS and FM of SiMA based resin were lower than those of Bis-GMA based resin (pcomposite materials: DC of EC was higher than that of Z250 (p0.05). SiMA had potential to replace Bis-GMA as base resin of dental composite materials. However, formulation of SiMA based resin and composite should be optimized in terms of mechanical strength to satisfy the requirements of resin based dental materials for clinical application

  2. Effect of metal primers and tarnish treatment on bonding between dental alloys and veneer resin.

    Science.gov (United States)

    Choo, Seung-Sik; Huh, Yoon-Hyuk; Cho, Lee-Ra; Park, Chan-Jin

    2015-10-01

    The aim of this study was to evaluate the effect of metal primers on the bonding of dental alloys and veneer resin. Polyvinylpyrrolidone solution's tarnish effect on bonding strength was also investigated. Disk-shape metal specimens (diameter 8 mm, thickness 1.5 mm) were made from 3 kinds of alloy (Co-Cr, Ti and Au-Ag-Pd alloy) and divided into 4 groups per each alloy. Half specimens (n=12 per group) in tarnished group were immersed into polyvinylpyrrolidone solution for 24 hours. In Co-Cr and Ti-alloy, Alloy Primer (MDP + VBATDT) and MAC-Bond II (MAC-10) were applied, while Alloy Primer and V-Primer (VBATDT) were applied to Au-Ag-Pd alloys. After surface treatment, veneering composite resin were applied and shear bond strength test were conducted. Alloy Primer showed higher shear bond strength than MAC-Bond II in Co-Cr alloys and Au-Ag-Pd alloy (PAg-Pd alloy surfaces presented significantly decreased shear bond strength. Combined use of MDP and VBATDT were effective in bonding of the resin to Co-Cr and Au-Ag-Pd alloy. Tarnish using polyvinylpyrrolidone solution negatively affected on the bonding of veneer resin to Co-Cr and Au-Ag-Pd alloys.

  3. Has resin-based composite replaced amalgam?

    Science.gov (United States)

    Christensen, Gordon J; Child, Paul L

    2010-02-01

    The major health organizations in the world continue to accept amalgam use, but the "amalgam war" of the 1800s is still going on. The end is not in sight. There is little disagreement that amalgam serves well and, although controversial, it appears to have minimal to no health hazards. There is a wide variation in the relative amount of amalgam placed in developed countries, and many dentists in North America do not use it. However, amalgam is still being used at least some of the time by the majority of practitioners in North America, and most of those practitioners also place resin-based composite in Class II locations. The evolution from amalgam to tooth-colored restorations has been a slow and tumultuous journey. The acceptability of resin-based composite in Class II locations continues to be a question for some dentists, while others have concluded that amalgam is "dead." It would be highly desirable if some of dentists using the alleged poisonous properties of amalgam as a "practice building" ploy would find more legitimate methods to increase their practice activity.

  4. A new approach to influence contact angle and surface free energy of resin-based dental restorative materials.

    Science.gov (United States)

    Rüttermann, Stefan; Trellenkamp, Taina; Bergmann, Nora; Raab, Wolfgang H-M; Ritter, Helmut; Janda, Ralf

    2011-03-01

    The purpose of the present study was to identify novel delivery systems and active agents which increase the water contact angle and reduce the surface free energy when added to resin-based dental restorative materials. Two delivery systems based on zeolite or novel polymeric hollow beads (Poly-Pore), loaded with two low surface tension active agents (hydroxy functional polydimethylsiloxane and polydimethylsiloxane) or a polymerizable active agent (silicone polyether acrylate) were used to modify commonly formulated experimental dental resin composites. The non-modified resin was used as a standard (ST). Flexural strength, flexural modulus, water sorption, solubility, polymerization shrinkage, surface roughness Ra, contact angle θ, total surface free energy γS, and the apolar γSLW, polar γSAB, Lewis acid γS+ and base γS- components, and the active agents surface tensions γL were determined (Ptension active agents were found not to influence the physical properties but to significantly increase the water contact angle and thus reduce surface free energy of dental resin composites. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  5. Effect of various teas on color stability of resin composites.

    Science.gov (United States)

    Dinç Ata, Gül; Gokay, Osman; Müjdeci, Arzu; Kivrak, Tugba Congara; Mokhtari Tavana, Armin

    2017-12-01

    To investigate the effect of various teas on color stability of resin composites. Two methacrylate-based (Arabesk Top, Grandio) and a silorane-based (Filtek Silorane) resin composites were used. 110 cylindrical samples of each resin composite were prepared (2 mm thickness and 8 mm diameter), polished and stored in distilled water (37°C for 24 hours). They were randomly divided into 11 groups (n= 10) and color measurements were taken. Then the samples were immersed in tap water (control), a black tea, a green tea or one of the eight herbal-fruit teas (37°C for 1 week) and subsequently subjected to the final color measurements. The color change of samples (ΔE*) was calculated, data were subjected to two-way ANOVA and Tukey's HSD tests. Teas, resin composites and their interactions were significant (P= 0.000). All the teas and control caused color changes in all three resin composites. Rosehip tea caused the most color changes, while tap water showed the least in all resin composites. Arabesk Top had the most staining potential in all the teas and control, whereas Filtek Silorane was the most stain resistant except Grandio immersed in sage tea. Color stability of all resin composites used were affected from both structure of resin materials and constituents of teas used. All resin composites were susceptible to staining by all teas especially rosehip tea. Arabesk Top composite showed the greatest color susceptibility in all teas and Filtek Silorane the least with one exception. Color of resin composites can be negatively affected from teas consumed. Clinicians should advise patients that drinking different kind of teas could intensify surface staining of resin based restorations.

  6. How much do resin-based dental materials release? A meta-analytical approach.

    Science.gov (United States)

    Van Landuyt, K L; Nawrot, Tim; Geebelen, B; De Munck, J; Snauwaert, J; Yoshihara, K; Scheers, Hans; Godderis, Lode; Hoet, P; Van Meerbeek, B

    2011-08-01

    Resin-based dental materials are not inert in the oral environment, and may release components, initially due to incomplete polymerization, and later due to degradation. Since there are concerns regarding potential toxicity, more precise knowledge of the actual quantity of released eluates is necessary. However, due to a great variety in analytical methodology employed in different studies and in the presentation of the results, it is still unclear to which quantities of components a patient may be exposed. The objective of this meta-analytical study was to review the literature on the short- and long-term release of components from resin-based dental materials, and to determine how much (order of magnitude) of those components may leach out in the oral cavity. Out of an initial set of 71 studies, 22 were included. In spite of the large statistical incertitude due to the great variety in methodology and lack of complete information (detection limits were seldom mentioned), a meta-analytical mean for the evaluated eluates was calculated. To relate the amount of potentially released material components with the size of restorations, the mean size of standard composite restorations was estimated using a 3D graphical program. While the release of monomers was analyzed in many studies, that of additives, such as initiators, inhibitors and stabilizers, was seldom investigated. Significantly more components were found to be released in organic than in water-based media. Resin-based dental materials might account for the total burden of orally ingested bisphenol A, but they may release even higher amounts of monomers, such as HEMA, TEGDMA, BisGMA and UDMA. Compared to these monomers, similar or even higher amounts of additives may elute, even though composites generally only contain very small amounts of additives. A positive correlation was found between the total quantity of released eluates and the volume of extraction solution. There is a clear need for more accurate

  7. 5-year clinical performance of resin composite versus resin modified glass ionomer restorative system in non-carious cervical lesions

    DEFF Research Database (Denmark)

    Franco, Eduardo Batista; Benetti, Ana Raquel; Ishikiriama, Sérgio Kiyoshi

    2006-01-01

    To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions.......To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions....

  8. [Comparison of surface roughness of nanofilled and microhybrid composite resins after curing and polishing].

    Science.gov (United States)

    Jiang, Hong; Lv, Da; Liu, Kailei; Zhang, Weisheng; Yao, Yao; Liao, Chuhong

    2014-05-01

    To compare the surface roughness of nanofilled dental composite resin and microhybrid composite resins after curing and polishing. A nanofilled composite (Z350) and 4 microhybrid composites (P60, Z250, Spectrum, and AP-X) were fabricated from the lateral to the medial layers to prepare 8 mm×8 mm×5 mm cubical specimens. The 4 lateral surfaces of each specimens were polished with abrasive disks (Super-Snap). Profilometer was used to test the mean surface roughness (Ra) after polishing. P60 had the lowest Ra (0.125∓0.030 µm) followed by Z250 and Spectrum. The Ra of Z350 (0.205∓0.052 µm) was greater than that of the other 3 resins, and AP-X had the roughest surfaces. Under scanning electron microscope, the polished faces of P60 resin were characterized by minor, evenly distributed particles with fewer scratches; the polished faces of Z350 presented with scratches where defects of the filling material could be seen. The nanofilled composite Z350 has smooth surface after polishing by abrasive disks, but its smoothness remains inferior to that of other micro-hybrid composite resins.

  9. Fatigue resistance of CAD/CAM resin composite molar crowns.

    NARCIS (Netherlands)

    Shembish, F.A.; Tong, H.; Kaizer, M.; Janal, M.N.; Thompson, V.P.; Opdam, N.J.M.; Zhang, Y.

    2016-01-01

    OBJECTIVE: To demonstrate the fatigue behavior of CAD/CAM resin composite molar crowns using a mouth-motion step-stress fatigue test. Monolithic leucite-reinforced glass-ceramic crowns were used as a reference. METHODS: Fully anatomically shaped monolithic resin composite molar crowns (Lava

  10. Effect of light-emitting diode and halogen light curing on the micro-hardness of dental composite and resin-modified glass ionomer cement: an in vitro study.

    Science.gov (United States)

    Bhalla, M; Patel, D; Shashikiran, N D; Mallikarjuna, R M; Nalawade, T M; Reddy, H K

    2012-01-01

    This in vitro study was conducted to evaluate and compare the micro-hardness of composite resin and resin-modified glass ionomer cement using light-emitting diode (LED) and halogen curing and also to inter-compare the effect of LED and halogen curing. The study sample comprised of 4 stainless steel plates with a thickness of 2 mm. For these stainless steel plates, holes were made to a diameter of 3 mm. The samples were divided into 4 groups of 8 each and labeled as group I, group II, group III, group IV, thus making provision for the two different modes of light exposure. In each group, the hole was restored with its respective restorative material and cured with light-curing unit according to manufacturer instructions. The results were statistically analyzed using Mann-Whitney test. It was concluded that the curing efficacy of the LED lamp was comparable to that of conventional halogen lamp, even with a 50% reduction in cure time, and resin composite (Filtek Z-250) presented the highest hardness values, whereas complete hardening of resin-modified glass ionomer cement (RMGIC) (Vitremer) was observed because of its self-curing system even after the removal of light source.

  11. Effect of light-emitting diode and halogen light curing on the micro-hardness of dental composite and resin-modified glass ionomer cement: An in vitro study

    Directory of Open Access Journals (Sweden)

    M Bhalla

    2012-01-01

    Full Text Available Aims : This in vitro study was conducted to evaluate and compare the micro-hardness of composite resin and resin-modified glass ionomer cement using light-emitting diode (LED and halogen curing and also to inter-compare the effect of LED and halogen curing. Materials and Methods : The study sample comprised of 4 stainless steel plates with a thickness of 2 mm. For these stainless steel plates, holes were made to a diameter of 3 mm. The samples were divided into 4 groups of 8 each and labeled as group I, group II, group III, group IV, thus making provision for the two different modes of light exposure. In each group, the hole was restored with its respective restorative material and cured with light-curing unit according to manufacturer instructions. The results were statistically analyzed using Mann-Whitney test. Results and conclusion: It was concluded that the curing efficacy of the LED lamp was comparable to that of conventional halogen lamp, even with a 50% reduction in cure time, and resin composite (Filtek Z-250 presented the highest hardness values, whereas complete hardening of resin-modified glass ionomer cement (RMGIC (Vitremer was observed because of its self-curing system even after the removal of light source.

  12. Analysis of the microstructure and mechanical performance of composite resins after accelerated artificial aging.

    Science.gov (United States)

    De Oliveira Daltoé, M; Lepri, C Penazzo; Wiezel, J Guilherme G; Tornavoi, D Cremonezzi; Agnelli, J A Marcondes; Reis, A Cândido Dos

    2013-03-01

    Researches that assess the behavior of dental materials are important for scientific and industrial development especially when they are tested under conditions that simulate the oral environment, so this work analyzed the compressive strength and microstructure of three composite resins subjected to accelerated artificial aging (AAA). Three composites resins of 3M (P90, P60 and Z100) were analyzed and were obtained 16 specimens for each type (N.=48). Half of each type were subjected to UV-C system AAA and then were analyzed the surfaces of three aged specimens and three not aged of each type through the scanning electron microscope (SEM). After, eight specimens of each resin, aged and not aged, were subjected to compression test. After statistical analysis of compressive strength values, it was found that there was difference between groups (α resin specimens aged P60 presented lower values of compressive strength statistically significant when compared to the not subject to the AAA. For the other composite resins, there was no difference, regardless of aging, a fact confirmed by SEM. The results showed that the AAA influenced the compressive strength of the resin aged P60; confirmed by surface analysis by SEM, which showed greater structural disarrangement on surface material.

  13. Effect of water storage and additional polymerization on the color parameters of flowable resin composites.

    Science.gov (United States)

    Harorli, Osman Tolga; Barutcigil, Çagatay; Bayindir, Yusuf Ziya; Bayindir, Funda

    2013-11-01

    Tooth colored dental restorative materials should maintain their chromatic properties throughout their service period. The aim of this study was to examine the possible color changes of flowable resin composite filling materials following water storage. The effect of additional light curing on color stability of restorative materials was also investigated. Six brands of light-cured flowable resin composites of the same shade (A3) were prepared from two groups generated by curing for 20 or 60 seconds. The initial color parameters of the flowable composite samples were measured with a dental colorimeter according to the CIELAB color scale, and the samples were stored in distilled water at 37°C. Following 2 weeks' water storage, the measurements were repeated. The color differences (ΔE*(ab)) were calculated according to the CIELAB formula. Statistical differences between the measurements were analyzed by ANOVA and Duncan's tests. No initial color variation between the samples cured for 20 seconds and 60 seconds was perceptible (ΔE*(ab)3.3, was detected in Eco-flow, Filtek Supreme and Grandio samples in both polymerization groups. Flowable resin composites may exhibit a significant color change as a result of water storage. Sixty seconds exposure period does not influence the final color. Clinicians should be aware of color shifts in flowable resins.

  14. In vitro study of Streptococcus mutans adhesion on composite resin coated with three surface sealants

    Directory of Open Access Journals (Sweden)

    Da Hye Kim

    2017-02-01

    Full Text Available Objectives Although the coating of surface sealants to dental composite resin may potentially reduce bacterial adhesion, there seems to be little information regarding this issue. This preliminary in vitro study investigated the adhesion of Streptococcus mutans (S. mutans on the dental composite resins coated with three commercial surface sealants. Materials and Methods Composite resin (Filtek Z250 discs (8 mm in diameter, 1 mm in thickness were fabricated in a mold covered with a Mylar strip (control. In group PoGo, the surfaces were polished with PoGo. In groups PS, OG, and FP, the surfaces polished with PoGo were coated with the corresponding surface sealants (PermaSeal, PS; OptiGuard, OG; Fortify Plus, FP. The surfaces of the materials and S. mutans cells were characterized by various methods. S. mutans adhesion to the surfaces was quantitatively evaluated using flow cytometry (n = 9. Results Group OG achieved the lowest water contact angle among all groups tested (p 0.05 or significantly lower (group OG, p < 0.001 bacterial adhesion when compared with the control group. Conclusions The application of the surface sealants significantly reduced S. mutans adhesion to the composite resin polished with the PoGo.

  15. Effects of Prepolymerized Particle Size and Polymerization Kinetics on Volumetric Shrinkage of Dental Modeling Resins

    Directory of Open Access Journals (Sweden)

    Tae-Yub Kwon

    2014-01-01

    Full Text Available Dental modeling resins have been developed for use in areas where highly precise resin structures are needed. The manufacturers claim that these polymethyl methacrylate/methyl methacrylate (PMMA/MMA resins show little or no shrinkage after polymerization. This study examined the polymerization shrinkage of five dental modeling resins as well as one temporary PMMA/MMA resin (control. The morphology and the particle size of the prepolymerized PMMA powders were investigated by scanning electron microscopy and laser diffraction particle size analysis, respectively. Linear polymerization shrinkage strains of the resins were monitored for 20 minutes using a custom-made linometer, and the final values (at 20 minutes were converted into volumetric shrinkages. The final volumetric shrinkage values for the modeling resins were statistically similar (P>0.05 or significantly larger (P<0.05 than that of the control resin and were related to the polymerization kinetics (P<0.05 rather than the PMMA bead size (P=0.335. Therefore, the optimal control of the polymerization kinetics seems to be more important for producing high-precision resin structures rather than the use of dental modeling resins.

  16. Interfacial microscopic examination and chemical analysis of resin-dentin interface of self-adhering flowable resin composite [version 3; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Tamer M. Hamdy

    2017-10-01

    Full Text Available Background: The newly introduced self-adhering flowable resin-composites decrease the required time for application by incorporation of an acidic adhesive monomer, thus reducing the number of steps, but its bonding is still uncertain. The aim of this study was to evaluate the interfacial microscopic examination and chemical analysis at the resin-dentin interface of a self-adhering flowable resin composite (Vertise™Flow Self-Adhering Flowable Composite, Kerr Dental, USA versus a total-etch (Te-Econom Plus resin composite, using an etching agent (Eco-Etch gel and bonding agent (Single Bond Universal. Methods: Sixteen freshly extracted sound human posterior teeth were used. The teeth were randomly divided into two groups: 8 specimens per type of composite. Standard-shaped class V cavities were prepared on the buccal surface. One group was restored by Te-Econom Plus resin composite by total-etch technique using Eco-Etch gel, which was applied to dentine for 15 seconds, followed by rinsing, drying and bonding agent application (Single Bond Universal. The other group restored directly with self-adhering resin composite (Vertise-Flow without application of etch or bond. Curing was done for 20 seconds using a light emitting diode light curing unit. Evaluation of the resin-dentin interface was done microscopically by examination of marginal gap distance in μm using scanning electron microscope (SEM, and chemical analysis of silver particles was observed using SEM with energy-dispersive X-ray spectrometry after 24 hours of specimen storage in ammoniacal silver nitrate. Results: Regarding marginal gap distance (µm and silver atomic % mean values, teeth restored with self-adhering resin composite (Vertise-Flow showed significantly higher mean values than the multi-step etch and rinse resin composite group (5.2 vs 0; 12.2 vs 8.2, respectively. Conclusions: Resin-dentin bonding using total-etch resin composite technique was more effective than self

  17. Microshear bond strength of composite resins to enamel and porcelain substrates utilizing unfilled versus filled resins.

    Science.gov (United States)

    Najafi-Abrandabadi, Ahmad; Najafi-Abrandabadi, Siamak; Ghasemi, Amir; Kotick, Philip G

    2014-11-01

    Failures such as marginal discoloration and composite chipping are still the problems of tooth-colored restorations on the substrate of enamel and porcelain, which some of these problems are consequently as a result of failures in the bonding layer. Using filled resin has been recently introduced to increase the bond strength of this layer. The aim of this study was to compare the microshear bond strength (μ-SBS) of composite resins to enamel incubated in periods of 24 h and 9 months and porcelain with unfilled resin and flowable composites (filled resin). In this in vitro study, two groups of 75 enamel samples with different storage times (24 h and 9 months) and a group of 75 porcelain samples were used. They were divided into 5 experimental groups of 15 samples in each. Composite cylinders in tygon tubes were bonded on the surface of acid-etched enamel and pretreated porcelain. Wave, Wave MV, Wave HV, Grandioflow and Margin Bond were used as bonding agents. The μ-SBS was measured at the speed of 1.0 mm/min. The bond strengths were analyzed with one-way analysis of variance (ANOVA) test followed by Tukey test. P composites (filled resins) can be used instead of unfilled resins in bonding composite resins to enamel and porcelain substrates.

  18. Effect of Children's Drinks on Color Stability of Different Dental Composites: An in vitro Study.

    Science.gov (United States)

    Habib, Ahmed Nour El-Din Ahmed; Abdelmoniem, Soad Abdelmoniem; Mahmoud, Sara Ahmed

    To assess the effect of four different children's drinks on color stability of resin dental composites. A total of one hundred and twenty specimens were prepared from Grandio SO, Filtek Z350 XT and Filtek Z250 XT (forty specimens each). Specimens were thermocycled, then each group was further subdivided into four subgroups (n=10) according to the immersion media which were chocolate milk, mango juice, orange fizzy drink, and water (control). The initial color parameters of each specimen were recorded before immersion (baseline) and color change values were recorded three and seven days after immersion in each solution using a digital spectrophotometer. Atomic force microscope was used to measure the surface roughness in randomly selected samples after one week immersion in children's drinks. All the children's drinks produced color changes in the examined resin dental composites, yet there was no statistical significant difference between the effects of tested drinks on the color changes (mean ΔE) of the three different dental composites (P>0.05). All tested children's drinks caused clinically unacceptable color changes of the tested resin dental composites. Immersion in chocolate milk and orange fizzy led to the highest color changes in the tested resin dental composites.

  19. Development of a low-color, color stable, dual cure dental resin.

    Science.gov (United States)

    Oei, James D; Mishriky, Maged; Barghi, Nasser; Rawls, H Ralph; Cardenas, H Lee; Aguirre, Rene; Whang, Kyumin

    2013-04-01

    Dual-cure (DC) resins are mainly used as cements due to high initial color (generally yellow) and large color shift (ΔE*) after polymerization as compared to light-cured resins. However, even as cements, this color shift is clinically unacceptable, especially when used to cement thin veneers. To develop a novel DC initiator system with both lower initial color (less yellow, i.e., whiter) and smaller ΔE*. The effect of using an allyl thiourea (T)/cumene hydroperoxide (CH) self-cure (SC) initiator system in combination with a photo-co-initiator, p-octyloxy-phenyl-phenyl iodonium hexafluoroantimonate (OPPI), in a commercial DC resin cement (PermaFlo DC, Ultradent Products, Inc.) was investigated. Initial color and ΔE* were assessed for 6 weeks in vitro under accelerated aging conditions (75°C water bath). Rockwell15T hardness was used to assess degree of cure (DoC) and the three-point bending test was used to assess mechanical properties. PermaFlo DC (control) was significantly harder than all experimental groups without OPPI but had up to three times higher initial color and four times greater color shift (ΔE*=27 vs. 8). With OPPI, hardness in the experimental groups increased significantly and several were comparable to the controls. Initial color and ΔE* increased slightly (ΔE*=9), but was still 3 times less than that of PermaFlo DC. DC samples containing OPPI had comparable modulus and ultimate transverse strengths to those of the controls. DC resins that use the T/CH initiator system are weaker but have extremely low color and ΔE*. The addition of OPPI increases DoC and mechanical properties to clinically acceptable levels and maintains extremely low color and ΔE*. With this novel initiator system, DC resins potentially can now have comparable color and color stability to light-cure resins and be used in broader esthetic dental applications to improve color stability and reduce shrinkage stress in restorative composites. Copyright © 2013 Academy of

  20. Preparation and Characterizations of Composite Material Based on Carbon Fiber and Two Thermoset Resins

    OpenAIRE

    Fouda Hany; Guo Lin; Elsharkawy Karim

    2017-01-01

    In the present investigation, we used two types of thermoset resins (epoxy resin and phenol formaldehyde resin) with carbon fiber (CF) to produce composite materials. CF/epoxy resin composite and CF/phenolformaldhyde resin composite were fabricated and compared between their mechanical properties as compression, tension and flexural. it was found that mechanical properties of CF/epoxy composite higher than mechanical properties of CF/phenolformaldhyde resin composite such as flexural strength...

  1. Color Stability of IDM Composite Resin

    Directory of Open Access Journals (Sweden)

    Ghavam M

    2000-06-01

    Full Text Available Discoloration of composite resins is considered to be a major factor in esthetic restoration"nfailures. The aim of this study was to evaluate color stability of IDM composite (both light and self cure"nsamples namely IL and IS, and to compare it with a self-cure composite (Degufill named DS and a light"ncure ormocer composite (Definite, called DL in the Report. 60 disk shaped samples of each composite"nwere prepared, according to ISO-7491. The samples were divided into 3 groups and aged as follows:"nA- (Control 7 days in dark 37°c chamber"nB- Foil covered and kept in 100% humidity, and 37°c in xenotest chamber for 24 hours, then transferred"nto a dark 37°c chamber for 6 more days."nC- Kept in 37°c, 100% humidity under the emission of xiiion lamp of xenotest chamber for 24 hours,"nand then transferred to 37°c dark chamber for 6 more days"nThe lightness and chromaticity values of samples were measured both before and after aging using a"nspectrophotometer (Data Flash. The total color changes as well as changes in lightness and chromaticity"nvalues were measured in the CIE L * a * b * scale, and analyzed. Color change was recorded to be"nsignificant in all samples after aging. The maximum change belonged to IL, which was significantly"ndifferent from DL and DS. It seems, in order to have a durable esthetic restoration using IDM, more"nscientific and professional consideration is needed in the production process.

  2. Synthesis and Characterization of a Polyimide-Epoxy Composite for Dental Applications

    Science.gov (United States)

    Yang, An; Xu, Chun

    2018-03-01

    Epoxy (EP) resins have been employed in dentistry for years, but their intrinsic brittleness demands a reinforcement to make them an ideal dental material that combines strength, toughness, and aesthetics. In this study, an EP resin was reinforced with a low-molecular-weight polyimide (PI). The PI/EP composites were subjected to three-point bending tests and examined by the scanning electron microscopy. It was found that blending PI with EP in proper proportions strengthened EP without sacrificing its toughness. The PI/EP composite could be employed in dentistry as the matrix of fiber-reinforced dental root canal posts.

  3. Are resin composites suitable replacements for amalgam? A study of two-body wear.

    Science.gov (United States)

    Lazaridou, Dimitra; Belli, Renan; Petschelt, Anselm; Lohbauer, Ulrich

    2015-07-01

    Wear resistance is an important property of the dental materials, particularly for large restorations in the posterior regions and for the patients suffering from parafunctional activities. Additionally, the wear resistance of flowable composite resin materials is a clinical concern, although they are popular among dentists because of their easy handling. The aims of the present study were to evaluate the wear resistance of nine composite resins both condensable (G-aenial posterior, Venus, GrandioSO, Tetric EvoCeram, Ceram X duo, Filtek Supreme XTE) and new-generation flowable resin composites (G-aenial Universal Flo, GrandioSO Flow and GrandioSO Heavy Flow) and to compare these results with amalgam. Eight specimens of each material were subjected to two-body wear tests, using a chewing simulator. The wear region of each material was examined under profilometer, measuring the vertical loss (μm) and the volume loss (mm(3)) of the materials. Additionally, SEM analysis was performed to assess surfaces irregularities. The results showed significant difference of the vertical loss and the volume loss of the examined materials (p amalgam had the best wear resistance, two condensable resin composites (GrandioSO, Ceram X duo) and all flowable materials had no significant difference with amalgam. GrandioSO had the highest wear resistance and Filtek Supreme XTE the lowest wear resistance. The majority of resin composites had good wear resistance and similar to amalgam. Based on the in vitro measurements of two-body wear resistance, the new resin composites could replace amalgam for restorations placed in occlusal stress-bearing regions. New-generation flowable resin materials may also be used in occlusal contact restorations.

  4. Cytotoxicity Evaluation of Two Bis-Acryl Composite Resins Using Human Gingival Fibroblasts.

    Science.gov (United States)

    Gonçalves, Fabiano Palmeira; Alves, Gutemberg; Guimarães, Vladi Oliveira; Gallito, Marco Antônio; Oliveira, Felipe; Scelza, Míriam Zaccaro

    2016-01-01

    Bis-acryl resins are used for temporary dental restorations and have shown advantages over other materials. The aim of this work was to evaluate the in vitro cytotoxicity of two bis-acryl composite resins (Protemp 4 and Luxatemp Star), obtained at 1, 7 and 40 days after mixing the resin components, using a standardized assay employing human primary cells closely related to oral tissues. Human gingival fibroblast cell cultures were exposed for 24 h to either bis-acryl composite resins, polystyrene beads (negative control) and latex (positive control) extracts obtained after incubation by the different periods, at 37 °C under 5% CO2. Cell viability was evaluated using a multiparametric procedure involving sequential assessment (using the same cells) of mitochondrial activity (XTT assay), membrane integrity (neutral red test) and total cell density (crystal violet dye exclusion test). The cells exposed to the resin extracts showed cell viability indexes exceeding 75% after 24 h. Even when cells were exposed to extracts prepared with longer conditioning times, the bis-acryl composite resins showed no significant cytotoxic effects (p>0.05), compared to the control group or in relation to the first 24 h of contact with the products. There were no differences among the results obtained for the bis-acryl composite resins evaluated 24 h, 7 days and 40 days after mixing. It may be concluded that the bis-acryl resins Protemp 4 and Luxatemp Star were cytocompatible with human gingival fibroblasts, suggesting that both materials are suitable for use in contact with human tissues.

  5. Preparation and Characterizations of Composite Material Based on Carbon Fiber and Two Thermoset Resins

    Directory of Open Access Journals (Sweden)

    Fouda Hany

    2017-01-01

    Full Text Available In the present investigation, we used two types of thermoset resins (epoxy resin and phenol formaldehyde resin with carbon fiber (CF to produce composite materials. CF/epoxy resin composite and CF/phenolformaldhyde resin composite were fabricated and compared between their mechanical properties as compression, tension and flexural. it was found that mechanical properties of CF/epoxy composite higher than mechanical properties of CF/phenolformaldhyde resin composite such as flexural strength of CF/epoxy resin composite increased by 30 % than flexural strength of CF/phenolformaldhyde resin composite, tensile strength of CF/epoxy resin composite increased by 11.4 % than flexural strength of CF/phenolformaldhyde resin and axial compression strength of CF/epoxy resin composite increased by 14.5 % than flexural strength of CF/phenolformaldhyde resin.

  6. Radiopacity Of Glass-ionomer/composite Resin Hybrid Materials.

    OpenAIRE

    Hara A.T.; Serra M.C.; Rodrigues Junior A.L.

    2001-01-01

    This study visually compared the radiopacity of seven restorative materials (3 resin-modified glass-ionomer cements, 3 polyacid-modified composite resins, and 1 conventional glass-ionomer cement) to a sound tooth structure sample, and an aluminium stepwedge. All hybrid materials were more radiopaque, except for one resin-modified glass-ionomer cement, than both the tooth structure and conventional glass-ionomer cement.

  7. Resin composite for sealing and its use in a solar cell. Fushiyo jushi soseibutsu oyobi sore wo mochiita taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Toma, H.; Mimura, T.; Takehara, N.

    1994-01-28

    This invention presents resin composites for sealing of a solar cell composed of a hardening resin and a thermoplastic resin which has a number average molecular weight larger than that of the hardening resin and is soluble in the hardening resin, and the invention affords a solar cell to endure a long-term stable operation and to give a good performance. The hardening resin includes unsaturated polyester resin, phenolic resin, alkyd resin, unsaturated acrylic resin, epoxy resin, polyurethane resin, melamine resin, diallyl phthalate resin, their oligomers and their modifications. The thermoplastic resin includes saturated polyester resin, phenolic resin, acrylic resin, styrene resin, epoxy resin, polyurethane resin, polyvinyl acetate resin, polyvinyl chloride resin, polyvinyl alcohol resin, polyacetal resin, their modifications and their copolymer resin. 2 figs., 3 tabs.

  8. Properties of Graphene Oxide/Epoxy Resin Composites

    OpenAIRE

    Jijun Tang; Haijun Zhou; Yunxia Liang; Xinlan Shi; Xin Yang; Jiaoxia Zhang

    2014-01-01

    The graphene oxide (GO) was obtained by pressurized oxidation method using natural graphite as raw materials. Then the GO/epoxy resin composites were prepared by casting. The mechanical and damping properties of composites were studied. As a result, the impact intensity of GO/epoxy resin composites was prominently improved with the content of the graphene oxide increasing. The glass transition temperature decreased and the damping capacity is improved.

  9. Shear Bond Strength between Fiber-Reinforced Composite and Veneering Resin Composites with Various Adhesive Resin Systems.

    Science.gov (United States)

    AlJehani, Yousef A; Baskaradoss, Jagan K; Geevarghese, Amrita; AlShehry, Marey A; Vallittu, Pekka K

    2016-07-01

    The aim of this research was to evaluate the shear bond strength of different laboratory resin composites bonded to a fiber-reinforced composite substrate with some intermediate adhesive resins. Mounted test specimens of a bidirectional continuous fiber-reinforced substrate (StickNet) were randomly assigned to three equal groups. Three types of commercially available veneering resin composites - BelleGlass®, Sinfony®, and GC Gradia® were bonded to these specimens using four different adhesive resins. Half the specimens per group were stored for 24 hours; the remaining were stored for 30 days. There were 10 specimens in the test group (n). The shear bond strengths were calculated and expressed in MPa. Data were analyzed statistically, and variations in bond strength within each group were additionally evaluated by calculating the Weibull modulus. Shear bond values of those composites are influenced by the different bonding resins and different indirect composites. There was a significant difference in the shear bond strengths using different types of adhesive resins (p = 0.02) and using different veneering composites (p veneering composite to bidirectional continuous fiber-reinforced substrate is influenced by the brand of the adhesive resin and veneering composite. © 2015 by the American College of Prosthodontists.

  10. Esthetic recovery of smile using composite resin and "biological posts" and crowns.

    Science.gov (United States)

    Vieira-Andrade, Raquel Gonçalves; Ribondi, Juliano Rodrigues; Botelho, Adriana Maria; Fernandes, Anacélia Mendes; Tavano, Karine Taís Aguiar

    2012-01-01

    The recovery of teeth that have been extensively destroyed by dental caries can be achieved through direct and indirect restorative procedures. This paper presents a case of the esthetic and functional recovery of permanent maxillary incisors with extensive dental caries in an adolescent patient through the use of a composite resin and "biological posts and crowns". A case report was drafted to describe the direct restoration of central maxillary incisors using composite resin and endodontic treatment of the lateral maxillary incisors, the construction of dentinal posts, the adaptation and cementing of the posts to the root canals, preparation and molding of crown portions, model construction, the choice of extracted teeth and the making and cementing of "biological crowns". The use of a composite resin and the cementing of "biological posts and crowns" reestablish dental esthetics and function. Biological restorations maintain all the characteristics of natural teeth and have a significant psychosocial impact on the patient's quality of life. However it should be stressed that this technique was only indicated in the present case after the determination of a significant improvement in oral hygiene.

  11. Comparative study between the radiopacity levels of high viscosity and of flowable composite resins, using digital imaging.

    Science.gov (United States)

    Arita, Emiko S; Silveira, Gilson P; Cortes, Arthur R; Brucoli, Henrique C

    2012-01-01

    The development of countless types and trends of high viscosite and flowable composite resins, with different physical and chemical properties applicable to their broad use in dental clinics calls for further studies regarding their radiopacity level. The aim of this study was to evaluate the radiopacity levels of high viscosity and the flowable composite resins, using digital imaging. 96 composite resin discs 5 mm in diameter and 3 mm thick were radiographed and analyzed. The image acquisition system used was the Digora® Phosphor Storage System and the images were analyzed with the Digora software for Windows. The exposure conditions were: 70 kVp, 8 mA, and 0.2 s. The focal distance was 40 cm. The image densities were obtained with the pixel values of the materials in the digital image. Most of the high viscosity composite resins presented higher radiopacity levels than the flowable composite resins, with statistically significant differences between the trends and groups analyzed (P composite resins, Tetric®Ceram presented the highest radiopacity levels and Glacier® presented the lowest. Among the flowable composite resins, Tetric®Flow presented the highest radiopacity levels and Wave® presented the lowest.

  12. Aerospace Composite Materials Delivery Order 0003: Nanocomposite Polymeric Resin Enhancements for Improved Composite Performance

    National Research Council Canada - National Science Library

    Chen, Chenggang

    2002-01-01

    .... The addition of clays does not significantly alter the viscosity or cure kinetics so that the modified resin will still be suitable for liquid composite molding techniques such as resin transfer molding...

  13. Moisture diffusion parameter characteristics for epoxy composites and neat resins

    Science.gov (United States)

    Long, E. R., Jr.

    1979-01-01

    The moisture absorption characteristics of two graphite/epoxy composites and their corresponding cured neat resins were studied in high humidity and water immersion environments at elevated temperatures. Moisture absorption parameters, such as equilibrium moisture content and diffusion coefficient derived from data taken on samples exposed to high humidity and water soak environments, were compared. Composite swelling in a water immersion environment was measured. Tensile strengths of cured neat resin were measured as a function of their equilibrium moisture content after exposure to different moisture environments. The effects of intermittent moderate tensile loads on the moisture absorption parameters of composite and cured neat resin samples were determined.

  14. Influence of nanometric silicon carbide on phenolic resin composites ...

    Indian Academy of Sciences (India)

    Phenolic resin; nanometric silicon carbide; nanocomposites; friction coefficient. 1. Introduction. Phenolic resin composites have their applications in a wide range of fields ... Curing time and temperature as well as mold materials influence the resulting homogeneity, glass transition temperature and mechanical properties.

  15. The measurement of polymerization shrinkage of composite resins with ESPI

    Science.gov (United States)

    Zhang, Zhang; Yang, Guo Biao

    2008-09-01

    In the current study, we used the method of electronic speckle pattern interferometry (ESPI) to measure polymerization shrinkage of composite resins. Standardized cavities were prepared and placed into the ESPI apparatus before the cavities were filled with composites (n=2) .The ESPI apparatus was constructed to measure the out-of-plane displacement of the resins surface during the polymerization. Experiments demonstrated that the ESPI technique was a viable method to measure the deformation of composite resins. It was responsive and sensitive to dimensional changes. We found that cavity shape, size and C- factor influenced the date of resins shrinkage. And the tooth deformation in response to polymerization of resins was measured by the ESPI too. We concluded that ESPI was a feasible method for assessing resins deformation induced by its polymerization shrinkage when it was bonded in tooth cavities. And the results were greatly influenced by the dimensions of cavities , or interface adhesive and so on. It could also measure the tooth deformation induced by shrinkage of bonded composite resins. We found that resins polymerization shrinkage date may overestimate shrinkage-induced tooth deformation.

  16. Fiber-reinforced Composite Resin Prosthesis to Restore Missing ...

    African Journals Online (AJOL)

    A fiber-reinforced composite inlay-onlay FPD was used for a single posterior tooth replacement in a patient refusing implant for psychological reasons. The FRC-FPD was made of pre-impregnated E-glass fibers (everStick, StickTeck, Turku, Finland) embedded in a resin matrix (Stick Resin, StickTeck, Turku, Finland).

  17. Synthesis of nanosized barium titanate/epoxy resin composites and ...

    Indian Academy of Sciences (India)

    Barium titanate/epoxy resin composites have been synthesized and tested for microwave absorption/ transmission. Nanocrystalline barium titanate (BaTiO3 or BT) ... Anechoic chamber; barium titanate; electromagnetic interference and compatibility; epoxy resin ..... electromagnetic waves, the two port calibrations have been.

  18. Characterization and Process Development of Cyanate Ester Resin and Composite

    Energy Technology Data Exchange (ETDEWEB)

    Frame, B.J.

    1998-03-01

    Cyanate ester (or polycyanate) resins offer advantages as composite matrices because of their high thermal stability, low outgassing, low water absorption and radiation resistance. This report describes the results of a processing study to develop high-strength hoop-wound composite by the wet-filament winding method using Toray T1000G carbon fiber and YLA RS-14A polycyanate resin as the constituent materials. Process trials, tests and analyses were conducted in order to gain insight into factors that can affect final properties of the cured cyanate ester resin and its composites. The study shows that the cyanate ester resin has a broad process envelope but that an inert-atmosphere cure is essential for obtaining optimum resin and composite properties. Minimizing moisture exposure prior to cure is also crucial as it affects the T{sub g} of the resin and composite. Recommendations for reducing moisture contact with the resin during wet-winding are presented. High fiber volume fraction ({approximately}80%) composites wound and cured with these methods yielded excellent hoop tensile strengths (660 to 670 ksi average with individual rings failing above 700 ksi), which are believed to be the highest recorded strengths for this class of materials. The measured transverse properties were also exceptional for these high fiber fraction composites. Based on the available data, this cyanate ester resin system and its composites are recommended for space and vacuum applications only. Further testing is required before these materials can be recommended for long term use at elevated temperatures in an ambient air environment. The results of all analyses and tests performed as part of this study are presented as well as baseline process for fabricating thick, stage-cured composites. The manufacture of a 1 in. thick composite cylinder made with this process is also described.

  19. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic

    International Nuclear Information System (INIS)

    Moradabadi, Ashkan; Roudsari, Sareh Esmaeily Sabet; Yekta, Bijan Eftekhari; Rahbar, Nima

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30 × magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. - Highlights: • Understanding the dominant mechanism of bonding

  20. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Moradabadi, Ashkan [Department of Electrochemistry, Universität Ulm, Ulm (Germany); Roudsari, Sareh Esmaeily Sabet [Department of Optoelectonics, Universität Ulm, Ulm (Germany); Yekta, Bijan Eftekhari [School of Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Rahbar, Nima, E-mail: nrahbar@wpi.edu [Department of Civil and Environmental Engineering, Worcester Polytechnic Institute, Worcester, MA 01609 (United States)

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30 × magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. - Highlights: • Understanding the dominant mechanism of bonding

  1. A Pragmatic Study Shows Failure of Dental Composite Fillings Is Genetically Determined: A Contribution to the Discussion on Dental Amalgams.

    Science.gov (United States)

    Vieira, Alexandre R; Silva, Marília B; Souza, Kesia K A; Filho, Arnôldo V A; Rosenblatt, Aronita; Modesto, Adriana

    2017-01-01

    Composite resins for posterior tooth restorations have become a viable alternative to dental amalgam. Failures sometimes cannot be easily explained, and we hypothesize that a genetic component may influence longevity of restorations. We aimed to determine if there is any evidence for a difference in the performance of amalgams versus composite resin in extensive posterior restorations. We also aimed to determine if risk factors such as age, sex, smoking tobacco, alcohol drinking, diabetes status, and periodontal health status may have a role in the failures of extensive anterior composite restorations. Finally, we investigated if genetic variation in matrix metalloproteinases that are present in the mineralized dentin is associated with failure of composite resin. The data used to perform this research were obtained from the Dental Registry and DNA Repository project after screening 4,856 patients. All restorations were evaluated at times of 1, 2, and 5 years after the restoration placement. 6,266 amalgam and 2,010 composite restorations were analyzed in a total of 807 patients in a period of approximately 10 years (period corresponding to the database existence). An additional 443 extensive direct composite resin restorations in anterior teeth were also studied. Failure rates of amalgam and composite restorations are similar, and by the end of 5 years, composites outperformed amalgams slightly. Failures of anterior composite restorations occurred more often in males who smoked tobacco ( p  = 0.05), despite a similar number of females and males that smoked tobacco in the sample (116 individuals smoked tobacco, 54 females and 62 males). Alcohol drinking increased failure rate within 2 years ( p  = 0.03). We found a statistically significant association between matrix metalloproteinase 2 rs9923304 and failure of composite restorations ( p  = 0.007). Composite resins can replace amalgam restorations. Smoking tobacco and drinking alcohol will

  2. A Pragmatic Study Shows Failure of Dental Composite Fillings Is Genetically Determined: A Contribution to the Discussion on Dental Amalgams

    Directory of Open Access Journals (Sweden)

    Alexandre R. Vieira

    2017-11-01

    Full Text Available Composite resins for posterior tooth restorations have become a viable alternative to dental amalgam. Failures sometimes cannot be easily explained, and we hypothesize that a genetic component may influence longevity of restorations. We aimed to determine if there is any evidence for a difference in the performance of amalgams versus composite resin in extensive posterior restorations. We also aimed to determine if risk factors such as age, sex, smoking tobacco, alcohol drinking, diabetes status, and periodontal health status may have a role in the failures of extensive anterior composite restorations. Finally, we investigated if genetic variation in matrix metalloproteinases that are present in the mineralized dentin is associated with failure of composite resin. The data used to perform this research were obtained from the Dental Registry and DNA Repository project after screening 4,856 patients. All restorations were evaluated at times of 1, 2, and 5 years after the restoration placement. 6,266 amalgam and 2,010 composite restorations were analyzed in a total of 807 patients in a period of approximately 10 years (period corresponding to the database existence. An additional 443 extensive direct composite resin restorations in anterior teeth were also studied. Failure rates of amalgam and composite restorations are similar, and by the end of 5 years, composites outperformed amalgams slightly. Failures of anterior composite restorations occurred more often in males who smoked tobacco (p = 0.05, despite a similar number of females and males that smoked tobacco in the sample (116 individuals smoked tobacco, 54 females and 62 males. Alcohol drinking increased failure rate within 2 years (p = 0.03. We found a statistically significant association between matrix metalloproteinase 2 rs9923304 and failure of composite restorations (p = 0.007. Composite resins can replace amalgam restorations. Smoking tobacco and drinking alcohol

  3. Surface roughness of etched composite resin in light of composite repair

    NARCIS (Netherlands)

    Loomans, B.A.C.; Cardoso, M.V.; Opdam, N.J.M.; Roeters, F.J.M.; Munck, J. De; Huysmans, M.C.D.N.J.M.; Meerbeek, B. Van

    2011-01-01

    OBJECTIVES: In search for clinically effective composite repair protocols, the effect of various etching protocols on the surface roughness of composite resins with different filler composition were investigated. METHODS: Of two composite resins (hybrid-filled Clearfil AP-X; nano-filled Filtek

  4. Fracture toughness, compressive strength and load-bearing capacity of short glass fibre-reinforced composite resin.

    Science.gov (United States)

    Garoushi, Sufyan; Vallittu, Pekka K; Lassila, Lippo V

    2011-01-01

    To investigate the reinforcing effect of short E-glass fibre fillers on fracture related mechanical properties of dental composite resin with a semi-interpenetrating polymer network (IPN) polymer matrix. Experimental short fibre composite (FC) resin was prepared by mixing 22.5 wt% of short E-glass fibres, 22.5 wt% of IPN-resin and 55 wt% of silane treated silica fillers using a high speed mixing machine. Test specimens were made bar shaped (3 × 6 × 25 mm3), cylindrical (6 mm length × 3 mm diameter) and cubic (9.5 × 5.5 × 3 mm3) from the experimental FC resin and conventional particulate composite resin (Grandio) as control. The test specimens (n = 8) were either dry stored or water stored (37°C for 30 days) before the mechanical tests. A three-point loading test and compression test were carried out according to ISO 10477 and a static loading test was carried out using a steel ball (Ø 3.0 mm) with a speed of 1.0 mm/min until fracture. Experimental fibre composite had a significantly higher mechanical performance for fracture toughness (14 MNm-1.5), compression strength (129 MPa) and static load-bearing capacity (1584 N) than the control composite (2 MNm-1.5, 112 MPa and 1031 N). The resin with short E-glass fibre fillers and IPN-polymer matrix yielded improved mechanical performance compared to the conventional particulate composite resin.

  5. Synthesis and characterization of dental composites

    Science.gov (United States)

    Djustiana, Nina; Greviana, Nadia; Faza, Yanwar; Sunarso

    2018-02-01

    During the last few decades, the increasing demands in esthetic dentistry have led to the development of dental composites material that provide similar appearance to the natural teeth. Recently, esthetic trend was an issue which increase the demand for teeth restorations that is similar with the origin. The esthetics of dental composite are more superior compared to amalgam, since its color look similar with natural teeth. Various dental composites have been developed using many type of fillers such as amorphous silica, quartz), borosilicate, Li-Sr-Ba-Al glass and oxide: zirconia and alumina. Researchers in Faculty of Dentistry University of Padjadjaran have prepared dental composites using zirconia-alumina-silica (ZAS) system as the filler. The aim is to improve the mechanical properties and the esthetic of the dental composites. The ZAS was obtained from chemical grade purity chemicals and Indonesia's natural sand as precursors its characterization were also presented. This novel method covers the procedure to synthesis and characterize dental composites in Padjadjaran University and some review about dental composites in global research.

  6. Monomer priming of denture teeth and its effects on the bond strength of composite resin.

    Science.gov (United States)

    Perea, Leila; Matinlinna, Jukka P; Tolvanen, Mimmi; Lassila, Lippo V; Vallittu, Pekka K

    2014-08-01

    The bond strength of acrylic resin denture teeth used as pontics in fiber-reinforced composite fixed dental prostheses needs to be improved. The purpose of this study was to assess the influence of various chemical surface-conditioning monomers on the ridge-lap surface of acrylic resin denture teeth by determining the strength of their bonding to a composite resin and changes in surface hardness. Acrylic resin denture teeth of 2 different brands (Artic 8 and Vitapan Cuspiform) (n=120) were tested. Four monomer systems were used as surface primers (conditioning): a flowable composite resin, methylmethacrylate 99%, composite primer, and a photopolymerizable dimethacrylate resin. Five surface-conditioning exposure times were used: no conditioning, 1, 5, 15, and 60 minutes. Surface microhardness measurements were made after the application of the monomer systems. Shear bond strength tests were subsequently performed, followed by a new surface microhardness indentation after the application of the load. The evaluation of the changes on specimen surfaces was performed with a scanning electron microscope. The differences between the shear bond strength and the surface hardness were evaluated for statistical significance by using a 3-way ANOVA. Tooth brand, monomer used, exposure time, and their 2- and 3-way interactions had a significant effect on the shear bond strength and hardness before and after testing, except for the 3-way interaction effect on hardness before testing. The chemical pretreatment of the ridge-lap surface of acrylic resin denture teeth increased the shear bond strength and influenced the surface hardness. The monomer systems caused dissolution on the denture surfaces. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  7. Repair Strength in Simulated Restorations of Methacrylate- or Silorane-Based Composite Resins.

    Science.gov (United States)

    Consani, Rafael Leonardo Xediek; Marinho, Tatiane; Bacchi, Atais; Caldas, Ricardo Armini; Feitosa, Victor Pinheiro; Pfeifer, Carmem Silvia

    2016-01-01

    The study verified the bond strength in simulated dental restorations of silorane- or methacrylate-based composites repaired with methacrylate-based composite. Methacrylate- (P60) or silorane-based (P90) composites were used associated with adhesive (Adper Single Bond 2). Twenty-four hemi-hourglass-shaped samples were repaired with each composite (n=12). Samples were divided according to groups: G1= P60 + Adper Single Bond 2+ P60; G2= P60 + Adper Single Bond 2 + P60 + thermocycling; G3= P90 + Adper Single Bond 2 + P60; and G4= P90 + Adper Single Bond 2 + P60 + thermocycling. G1 and G3 were submitted to tensile test 24 h after repair procedure, and G2 and G4 after submitted to 5,000 thermocycles at 5 and 55 ?#61616;C for 30 s in each bath. Tensile bond strength test was accomplished in an universal testing machine at crosshead speed of 0.5 mm/min. Data (MPa) were analyzed by two-way ANOVA and Tukey's test (5%). Sample failure pattern (adhesive, cohesive in resin or mixed) was evaluated by stereomicroscope at 30?#61655; and images were obtained in SEM. Bond strength values of methacrylate-based composite samples repaired with methacrylate-based composite (G1 and G2) were greater than for silorane-based samples (G3 and G4). Thermocycling decreased the bond strength values for both composites. All groups showed predominance of adhesive failures and no cohesive failure in composite resin was observed. In conclusion, higher bond strength values were observed in methacrylate-based resin samples and greater percentage of adhesive failures in silorane-based resin samples, both composites repaired with methacrylate-based resin.

  8. Surface discoloration of composite resins: Effects of staining and bleaching

    Science.gov (United States)

    Poggio, Claudio; Beltrami, Riccardo; Scribante, Andrea; Colombo, Marco; Chiesa, Marco

    2012-01-01

    Background: The purpose of this in vitro study was to evaluate surface discoloration of three microhybrid composite resins (Esthet•X HD, Clearfil AP-X, Gradia Direct) and five nanohybrid composite resins (Ceram•X, GC Kalore, G-aenial, Grandio, GrandioSO), after staining and bleaching procedures. Materials and Methods: The composite resins were polymerized with a curing light (Celalux II, Voco, Cuxhaven, Germany) into 160 silicon molds (6,4 mm in diameter and 2 mm in thickness) to obtain identical specimens. Twenty samples for each composite resin were prepared. The specimens were polished using an automated polishing machine with the sequence of 600-, 800-, 1000-grit abrasive paper under water irrigation. The specimens were immersed in tea and distilled water: the specimens were dipped for 20 min, once a day (every 24 h), for 14 days into the drinks. The specimens were then bleached with carbamide peroxide at 17% (Perfect Bleach-Voco). The color of specimens was measured with a spectrophotometer according to the CIE L*a*b* system after light-polymerization of composite resin specimens, after 7 days, after 14 days, and after bleaching. The color difference h index (DEab*) between each measurement was calculated. Statistical analysis was made using analysis of variance (ANOVA). Results: All specimens showed a significant increase in staining with a similar trend and no significant differences between microhybrid and nanohybrid composite resins. After whitening procedures, materials tested showed both significant and unsignificant differences of the h index. Conclusions: Microhybrid and nanohybrid composite resins had similar in vitro surface discoloration in tea. After bleaching, discoloration was removed from some composite resins tested. PMID:23559921

  9. Surface discoloration of composite resins: Effects of staining and bleaching

    Directory of Open Access Journals (Sweden)

    Claudio Poggio

    2012-01-01

    Full Text Available Background: The purpose of this in vitro study was to evaluate surface discoloration of three microhybrid composite resins (Esthet·X HD, Clearfil AP-X, Gradia Direct and five nanohybrid composite resins (Ceram·X, GC Kalore, G-aenial, Grandio, GrandioSO, after staining and bleaching procedures. Materials and Methods: The composite resins were polymerized with a curing light (Celalux II, Voco, Cuxhaven, Germany into 160 silicon molds (6,4 mm in diameter and 2 mm in thickness to obtain identical specimens. Twenty samples for each composite resin were prepared. The specimens were polished using an automated polishing machine with the sequence of 600-, 800-, 1000-grit abrasive paper under water irrigation. The specimens were immersed in tea and distilled water: the specimens were dipped for 20 min, once a day (every 24 h, for 14 days into the drinks. The specimens were then bleached with carbamide peroxide at 17% (Perfect Bleach-Voco. The color of specimens was measured with a spectrophotometer according to the CIE LFNx01aFNx01bFNx01 system after light-polymerization of composite resin specimens, after 7 days, after 14 days, and after bleaching. The color difference h index (DE abFNx01 between each measurement was calculated. Statistical analysis was made using analysis of variance (ANOVA. Results: All specimens showed a significant increase in staining with a similar trend and no significant differences between microhybrid and nanohybrid composite resins. After whitening procedures, materials tested showed both significant and unsignificant differences of the h index. Conclusions: Microhybrid and nanohybrid composite resins had similar in vitro surface discoloration in tea. After bleaching, discoloration was removed from some composite resins tested.

  10. Surface discoloration of composite resins: Effects of staining and bleaching.

    Science.gov (United States)

    Poggio, Claudio; Beltrami, Riccardo; Scribante, Andrea; Colombo, Marco; Chiesa, Marco

    2012-09-01

    The purpose of this in vitro study was to evaluate surface discoloration of three microhybrid composite resins (Esthet•X HD, Clearfil AP-X, Gradia Direct) and five nanohybrid composite resins (Ceram•X, GC Kalore, G-aenial, Grandio, GrandioSO), after staining and bleaching procedures. The composite resins were polymerized with a curing light (Celalux II, Voco, Cuxhaven, Germany) into 160 silicon molds (6,4 mm in diameter and 2 mm in thickness) to obtain identical specimens. Twenty samples for each composite resin were prepared. The specimens were polished using an automated polishing machine with the sequence of 600-, 800-, 1000-grit abrasive paper under water irrigation. The specimens were immersed in tea and distilled water: the specimens were dipped for 20 min, once a day (every 24 h), for 14 days into the drinks. The specimens were then bleached with carbamide peroxide at 17% (Perfect Bleach-Voco). The color of specimens was measured with a spectrophotometer according to the CIE L(*)a(*)b(*) system after light-polymerization of composite resin specimens, after 7 days, after 14 days, and after bleaching. The color difference h index (DEab(*)) between each measurement was calculated. Statistical analysis was made using analysis of variance (ANOVA). All specimens showed a significant increase in staining with a similar trend and no significant differences between microhybrid and nanohybrid composite resins. After whitening procedures, materials tested showed both significant and unsignificant differences of the h index. Microhybrid and nanohybrid composite resins had similar in vitro surface discoloration in tea. After bleaching, discoloration was removed from some composite resins tested.

  11. Resin flow/fiber deformation model for composites

    International Nuclear Information System (INIS)

    Gutowski, T.G.

    1985-01-01

    This paper presents a resin flow/fiber deformation model that can be used to predict the behavior of composites during the molding cycle. The model can take into account time varying pressure and viscosity and output the time history of the fiber volume fraction. With this known, the composite thickness, resin pressure, and fiber pressure can all be determined as a function of time. The results of this model are in good agreement with experimentally measured values. 10 references, 9 figures

  12. Microleakage of four composite resin systems in class II restorations.

    Science.gov (United States)

    Majeed, A; Osman, Y I; Al-Omari, T

    2009-11-01

    To compare the microleakage at the enamel and dentine/cementum margins of three nanocomposites and a microhybrid composite in Class II restorations. Four light-cured dental resin restorative materials in combination with their respective bonding agents were investigated. Eighty non-carious, extracted human molars were divided into 4 groups of 20 teeth each. The apices of the teeth were sealed with a resin modified glass ionomer cement. Standardized Class II slot cavities were prepared on the proximal surfaces of each tooth. Each group had an equal number of cavities with gingival margins on enamel and on dentine/cementum. Restorations were placed as indicated: Group 1 (G1): Ceram-X mono/Prime & Bond NT (Dentsply), G2: Premise/ OptiBond Solo Plus (Kerr), G3: Grandio/Admira Bond (VOCO), G4: Z100/Adper Scotchbond Multi-Purpose (3M ESPE). After thermocycling and immersion in 0.5% methylene blue dye solution, the teeth were sectioned and dye penetration was scored on a scale of 0 to 3 on both the enamel and dentine/cementum margins. The data were analyzed using a Kruskal-Wallis one way ANOVA and Mann-Whitney U test of ranks (significance at p Grandio/Admira Bond showed significantly lower microleakage when compared to the other materials tested while Z100/Adper Scotchbond Multi-Purpose showed the largest microleakage (p Grandio/Admira Bond showing the least microleakage when compared to the other three materials tested. At the enamel margins, all materials tested performed reasonably well.

  13. Marginal adaptation of composite resins under two adhesive techniques.

    Science.gov (United States)

    Dačić, Stefan; Veselinović, Aleksandar M; Mitić, Aleksandar; Nikolić, Marija; Cenić, Milica; Dačić-Simonović, Dragica

    2016-11-01

    In the present research, different adhesive techniques were used to set up fillings with composite resins. After the application of etch and rinse or self etch adhesive technique, marginal adaptation of composite fillings was estimated by the length of margins without gaps, and by the microretention of resin in enamel and dentin. The study material consisted of 40 extracted teeth. Twenty Class V cavities were treated with 35% phosphorous acid and restored after rinsing by Adper Single Bond 2 and Filtek Ultimate-ASB/FU 3M ESPE composite system. The remaining 20 cavities were restored by Adper Easy One-AEO/FU 3M ESPE composite system. Marginal adaptation of composite fillings was examined using a scanning electron microscope (SEM). The etch and rinse adhesive technique showed a significantly higher percentage of margin length without gaps (in enamel: 92.5%, in dentin: 57.3%), compared with the self-etch technique with lower percentage of margin length without gaps, in enamel 70.4% (p resin tugs in interprismatic spaces of enamel, while the dentin microretention was composed of adhesive and hybrid layers with resin tugs in dentin canals. In the second technique, resin tugs were rarely seen and a microgap was dominant along the border of restoration margins. The SEM analysis showed a better marginal adaptation of composite resin to enamel and dentin with better microretention when the etch and rinse adhesive procedure was applied. © 2016 Wiley Periodicals, Inc.

  14. Flowable resin used as a sealant in molars affected by dental fluorosis: a comparative study.

    Science.gov (United States)

    Loyola-Rodriguez, Juan Pablo; Mendoza-Razo, Veronica; Rodriguez-Juarez, Fernando; Campos-Cambranis, Rafael

    2005-01-01

    The decline in prevalence and incidence of dental caries in developed countries over the last two decades is considered to be due mainly to the widespread use of fluoride in different forms, but simultaneously with decline in caries, an increase in dental fluorosis has been reported. The aim of this study was to compare the Conventional Sealant Technique (CST) and Enameloplasty Sealant Technique (EST) using a flowable resin as sealant in molars affected by dental fluorosis. A total of 40 extracted third molars affected by dental fluorosis were divided at random into two groups of 20 teeth each, and Tetric Flow resin was used as sealant. All teeth were studied for lateral adaptation and resin penetration by direct and indirect techniques; all samples were replicated in epoxy resin and were evaluated with Scanning Electron Microscopy (SEM). The results demonstrated that EST allowed a deeper sealant penetration and a superior sealant adaptation than CST, both in direct and indirect evaluations by SEM. The most important variables being penetration-interface and penetration depth both being statistically significant (pceromer is an excellent material alternative to be used as sealant and that EST is quite necessary in molars affected by dental fluorosis, the combination of both being a reliable method to be used as primary prevention approach of dental caries in endemic areas of dental fluorosis.

  15. Direct composite resin layering techniques for creating lifelike CAD/CAM-fabricated composite resin veneers and crowns.

    Science.gov (United States)

    LeSage, Brian

    2014-07-01

    Direct composite resin layering techniques preserve sound tooth structure and improve function and esthetics. However, intraoral placement techniques present challenges involving isolation, contamination, individual patient characteristics, and the predictability of restorative outcomes. Computer-aided design and computer-aided manufacturing (CAD/CAM) restorations enable dentists to better handle these variables and provide durable restorations in an efficient and timely manner; however, milled restorations may appear monochromatic and lack proper esthetic characteristics. For these reasons, an uncomplicated composite resin layering restoration technique can be used to combine the benefits of minimally invasive direct restorations and the ease and precision of indirect CAD/CAM restorations. Because most dentists are familiar with and skilled at composite resin layering, the use of such a technique can provide predictable and highly esthetic results. This article describes the layered composite resin restoration technique. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  16. Assessment of polymerization contraction stress of three composite resins

    NARCIS (Netherlands)

    Cadenaro, M.; Biasotto, M.; Scuor, N.; Breschi, L.; Davidson, C.L.; Di Lenarda, R.

    2008-01-01

    Objectives: The purpose of this study was to measure the development of contraction stress of three composite resin restorative materials during photo-polymerization: a micro-hybrid composite (Filtek Z250, 3M ESPE, St. Paul, MN, USA); a nano-filled composite (Filtek Supreme, 3M ESPE, St. Paul, MN,

  17. Studying Room Temperature Curing of Phenolic Resin and their Composites

    Directory of Open Access Journals (Sweden)

    M.H. Beheshty

    2007-10-01

    Full Text Available Phenolic resins are synthetic low molecular weight thermoset resins which are polymerized and cured to higher molecular weights by condensation method. These resins have high weathering resistance, high oxidative thermal properties and good chemical resistance. Phenolic resins can be cured thermally or by acid curing. The most common method of curing phenolic resin is by thermal curing that takes place in the range of 130-180oC. At room temperature, however, phenolic resins are cured by acid catalysts. In this paper, room temperature curing of resol phenolic resin by para toluene sulphonic acid has been investigated. The acid quantity has been determined for room temperature curing of two types of resols to achieve a reasonable hardness and gelation time. Temperature curing and thermal stability of respective resins have been investigated by DSC and TGA, respectively. A glass-phenolic composite plate has been prepared and cured by these two methods. The results show that the optimum amount of acid is 20% by weight. Optimum mechanical properties, chemical resistance and thermal properties have been achieved for acid cured system. The hot cured resin, however, has better properties.

  18. In vitro two-body wear of inlay-onlay composite resin restoratives.

    Science.gov (United States)

    Burgoyne, A R; Nicholls, J I; Brudvik, J S

    1991-02-01

    Inlay-onlay composite resin restorations have been introduced to the profession as alternatives to amalgam and direct composite resins. Two-body wear testing was performed on three inlay-onlay resins and one direct composite resins using a machine designed to produce sliding wear. The composite resins were opposed by human enamel, type III gold alloy, and porcelain. Of the investigated materials, the homogeneously microfilled inlay-onlay material showed significantly less wear. The direct composite resin showed significantly the greatest wear. The hybrid inlay-onlay resins showed intermediate wear. The hybrid inlay-onlay resins and the direct composite (small particle, heavily filled) resin created wear tracks in the opposing surfaces while the homogeneous microfill inlay-onlay resin did not. The depth of the observed wear tracks in the opposing surface was sufficiently substantial to warrant further investigation into the wear of materials that oppose composite resin restorations.

  19. Influence of Finishing and Polishing Techniques and Abrasion on Transmittance and Roughness of Composite Resins.

    Science.gov (United States)

    Carneiro, Pma; Ramos, T M; de Azevedo, C S; de Lima, E; de Souza, Shj; Turbino, M L; Cesar, P F; Matos, A B

    The aim of this study was to evaluate the influence of finishing and polishing systems and toothbrush abrasion on transmittance (T) and surface roughness (Ra) of three composite resins (Filtek Z350 XT, Tetric N-Ceram, and IPS Empress Direct). Eighteen resin disks (10 mm diameter × 2 mm thick) finished by polyester strips had initial surface smoothness recorded, representing phase 1 (P1). Specimens were divided into three groups (n=6) according to the finishing/polishing instrument used (OneGloss, TopGloss, and Sof-Lex) to compose phase 2 samples (P2). Then specimens were subjected to 514 cycles of toothbrush simulation using a toothpaste slurry, with a constant load applied to soft bristles, and were then washed (phase 3=P3). After each phase, the specimens were examined by an optical profiler and spectrophotometer to measure Ra and T. Data were analyzed by analysis of variance, Tukey and Pearson tests. T values were statistically influenced by composite resin ( p=0.000) and phase of measurement ( p=0.000) factors, while the finishing/polishing system used ( p=0.741) did not affect T. On the other hand, Ra values were statistically affected by the factor finishing/polishing system ( p=0.000), but not by composite resin ( p=0.100) and phase of measurement ( p=0.451). Tetric N-Ceram and Empress Direct presented higher values of roughness when polished by OneGloss, while TopGloss and Sof-Lex showed a lower roughness. It can be concluded that composite resins transmitted more light after dental abrasion. Transmittance of composite resins was not modified by the distinct roughness created by finishing/polishing instruments.

  20. Radiation processed composite materials of wood and elastic polyester resins

    International Nuclear Information System (INIS)

    Tapolcai, I.; Czvikovszky, T.

    1983-01-01

    The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of wood composite materials. (author)

  1. Effect of ultraviolet light irradiation on bonding of experimental composite resin artificial teeth.

    Science.gov (United States)

    Loyaga-Rendon, Paola G; Takahashi, Hidekazu; Iwasaki, Naohiko; Reza, Fazal

    2007-11-01

    The purpose of the present study was to evaluate how ultraviolet light (UV) irradiation using an ordinary UV sterilizer would affect the bonding of experimental composite resins to an autopolymerizing acrylic resin. To this end, three composite resins and one unfilled resin--of which the compositions were similar to commercial composite resin artificial teeth--were prepared as repair composites. Their shear bond strengths after UV irradiation for one to 60 minutes were significantly greater than those before UV irradiation regardless of composite resin type. Failure mode after UV irradiation for one to 60 minutes was mainly cohesive failure of the composite resins, but that before UV irradiation and after 24 hours' irradiation was mainly adhesive failure. These results thus suggested that a short period of UV irradiation on composite resin teeth would improve the bonding efficacy of composite resin artificial teeth to autopolymerizing resin.

  2. Dynamic cure measurement of dental polymer composites using optical coherence tomography

    Science.gov (United States)

    Tomlins, Peter H.; Palin, Will M.; Shortall, Adrian C.

    2008-02-01

    Dental amalgam is being increasingly replaced by Light-activated resin-based dental composites. However, these materials are limited by inefficient setting reactions as a function of depth, constraining the maximum extent of cure and reducing biocompatibility. In this paper we demonstrate a novel metrological tool for dynamic monitoring of refractive index and thickness change through curing resins using spectral-domain optical coherence tomography. We present real-time measurements from pre- to post-cure of a series of un-filled bisphenol-A diglycidyl ether dimethacrylate (bisGMA) and triethylene glycol dimethacrylate (TEGDMA) resins with different inhibitor concentrations. Our results demonstrate that refractive index measurements are sensitive to the extent of cure of such resins and that the inhibitor concentration strongly affects the cure dynamics and final extent of cure.

  3. Shrinkage reduction of dental composites by addition of expandable zirconia filler

    DEFF Research Database (Denmark)

    Skovgaard, M.; Almdal, Kristoffer; Sørensen, Bent F.

    2011-01-01

    A problem with dental resin composites is the polymerization shrinkage, which makes the filling loosen from the tooth or induces crack formation. We have developed an expandable metastable tetragonal zirconia filler, which upon reaction with water, is able to counter the polymer shrinkage...

  4. Fiber reinforced silicon-containing arylacetylene resin composites

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available A silicon-containing arylacetylene resin (SAR, a poly(dimethylsilyleneethynylene phenyleneethynylene (PMSEPE, was synthesized. The PMSEPE is a solid resin at ambient temperature with a softening temperature about 60°C and soluble in some solvents like tetrahydrofuran. The melt viscosity of the PMSEPE resin is less than 1 Pa•s. The resin could cure at the temperature of lower than 200°C. Fiber reinforced PMSEPE composites were prepared from prepregs which were made by the impregnation of fibers in PMSEPE resin solution. The composites exhibit good mechanical properties at room temperature and 250°C. The observation on fracture surfaces of the composites reinforced by glass fibers and carbon fibers demonstrates that the adhesion between the fibers and resin is good. The results from an oxyacetylene flame test show that the composites have good ablation performance and XRD analyses indicate that SiC forms in the residues during the ablation of the composites.

  5. A comparative study to determine strength of autopolymerizing acrylic resin and autopolymerizing composite resin influenced by temperature during polymerization: An In Vitro study

    OpenAIRE

    Anuj Chhabra; I V Rudraprasad; D B Nandeeshwar; C Nidhi

    2017-01-01

    Aim: Temporary coverage of a prepared tooth is an important step during various stages of the fixed dental prosthesis. Provisional restorations should satisfy proper mechanical requirements to resist functional and nonfunctional loads. A few studies are carried out regarding the comparison of the effect of curing environment, air and water, on mechanical properties of autopolymerizing acrylic and composite resin. Hence, the aim of this study was to compare the transverse strength of autopolym...

  6. Correlating cytotoxicity to elution behaviors of composite resins in term of curing kinetic.

    Science.gov (United States)

    Meng, Junquan; Yang, Huichuan; Cao, Man; Li, Lei; Cai, Qing

    2017-09-01

    Cytotoxicity of photocurable composite resins is a key issue for their safe use in dental restoration. Curing kinetic and elution behaviors of the composite resin would have decisive effects on its cytotoxicity. In this study, composite resins composed of bisphenol-glycidyl dimethacrylate (Bis-GMA), triethyleneglycol dimethacrylate (TEGDMA), camphorquinone (CQ), N,N-dimethylaminoethyl methacrylate (DMAEMA) and barium glass powders were prepared by setting the photoinitiators CQ/DMAEMA at 0.5wt%, 1wt% or 3wt% of the total weight of Bis-GMA/TEGDMA. The ratio of Bis-GMA/TEGDMA was 6:4, the ratio of CQ/DMAEMA was 1:1, and the incorporated inorganic powder was 75wt%. Then, curing kinetics were studied by using real-time Fourier transform infrared spectroscopy (FTIR) and photo-DSC (differential scanning calorimeter). Elution behaviors in both ethanol solution and deionized water were monitored by using liquid chromatogram/mass spectrometry (LC/MS). Cytotoxicity was evaluated by in vitro culture of L929 fibroblasts. Finally, they were all analyzed and correlated in terms of initiator contents. It was found that the commonly used 0.5wt% of photoinitiators was somewhat insufficient in obtaining composite resin with low cytotoxicity. Copyright © 2017. Published by Elsevier B.V.

  7. Composition of asphaltenes and resins of west Siberian petroleums

    Energy Technology Data Exchange (ETDEWEB)

    Goncharov, I.V.; Babicheva, T.A.; Bodak, A.N.; Nemirovskaya, G.B.; Mashigorov, A.A.

    1985-01-01

    ESR and X-ray diffraction analysis was used to examine asphaltene and resin samples of West Siberia. Experiments were carried out to simulate the effect of catagenesis on resin and asphaltene composition. Processes of thermocatalytic transformations of crude oil in the deposit were found to have no marked effect on asphaltene and resin composition. Transformation of the organic input at sedimentation was assumed to be the main factor determining the qualitative and quantitative composition of crude oil resins and asphaltenes of West Siberia. Petroleums formed from organic matter, accumulating under reducing conditions, contain more asphaltenes and resins, they include much tetravalent vanadium and the asphaltenes have abundant paramagnetic centres. Petroleums formed from oxidized organic matter contain very little asphaltene low concentrations of paramagnetic centers, and little tetravalent vanadium. Resins of these petroleums are rich in oxygen. High levels of asphalt-resin matter in petroleums is related to the presence in the initial organic progenitors of polyunsaturated fatty acids and various nitrogen- and sulfur-containing compounds.

  8. Effects of Wet and Dry Finishing and Polishing on Surface Roughness and Microhardness of Composite Resins

    Directory of Open Access Journals (Sweden)

    Negin Nasoohi

    2017-08-01

    Full Text Available Objectives: This study aimed to assess the effect of wet and dry finishing and polishing on microhardness and roughness of microhybrid and nanohybrid composites.Materials and Methods: Thirty samples were fabricated of each of the Polofil Supra and Aelite Aesthetic All-Purpose Body microhybrid and Grandio and Aelite Aesthetic Enamel nanohybrid composite resins. Each group (n=30 was divided into three subgroups of D, W and C (n=10. Finishing and polishing were performed dry in group D and under water coolant in group W. Group C served as the control group and did not receive finishing and polishing. Surface roughness of samples was measured by a profilometer and their hardness was measured by a Vickers hardness tester. Data were analyzed using two-way ANOVA (P<0.05.Results: The smoothest surfaces with the lowest microhardness were obtained under Mylar strip without finishing/polishing for all composites (P<0.0001. The highest surface roughness was recorded for dry finishing/polishing for all composites (P<0.0001. Dry finishing/polishing increased the microhardness of all composites (P<0.0001.Conclusions: Dry finishing and polishing increases the microhardness and surface roughness of microhybrid and nanohybrid composite resins. Keywords: Composite Resins; Dental Polishing; Hardness

  9. Influence of irradiance on Knoop hardness, degree of conversion, and polymerization shrinkage of nanofilled and microhybrid composite resins.

    Science.gov (United States)

    Fugolin, Ana Paula Piovezan; Correr-Sobrinho, Lourenço; Correr, Américo Bortolazzo; Sinhoreti, Mário Alexandre Coelho; Guiraldo, Ricardo Danil; Consani, Simonides

    2016-01-01

    The purpose of this study was to investigate the influence of the irradiance emitted by a light-curing unit on microhardness, degree of conversion (DC), and gaps resulting from shrinkage of 2 dental composite resins. Cylinders of nanofilled and microhybrid composites were fabricated and light cured. After 24 hours, the tops and bottoms of the specimens were evaluated via indentation testing and Fourier transform infrared spectroscopy to determine Knoop hardness number (KHN) and DC, respectively. Gap width (representing polymerization shrinkage) was measured under a scanning electron microscope. The nanofilled composite specimens presented significantly greater KHNs than did the microhybrid specimens (P composite resin exhibited significantly greater DC and gap width than the nanofilled material (P composite resins.

  10. Clinical performance of a hybrid resin composite with and without an intermediate layer of flowable resin composite: a 7-year evaluation

    DEFF Research Database (Denmark)

    van Dijken, Jan W V; Pallesen, Ulla

    2011-01-01

    The objective of this prospective clinical follow up was to evaluate the long term clinical performance of a hybrid resin composite in Class II restorations with and without intermediate layer of flowable resin composite.......The objective of this prospective clinical follow up was to evaluate the long term clinical performance of a hybrid resin composite in Class II restorations with and without intermediate layer of flowable resin composite....

  11. Restored viability and function of dental pulp cells on poly-methylmethacrylate (PMMA)-based dental resin supplemented with N-acetyl cysteine (NAC).

    Science.gov (United States)

    Kojima, N; Yamada, M; Paranjpe, A; Tsukimura, N; Kubo, K; Jewett, A; Ogawa, T

    2008-12-01

    This study examines cytotoxicity of poly-methylmethacrylate (PMMA)-based dental temporary filling resin to dental pulp cells, and the potential amelioration of the toxicity with an anti-oxidant amino-acid, N-acetyl cysteine (NAC). Dental pulp cells extracted from rat maxillary incisors were cultured on the resin material with or without NAC incorporation, or on the polystyrene. The cultures were supplied with osteoblastic media, containing dexamethasone. Forty five percent of cells on the PMMA dental resin were necrotic at 24h after seeding. However, this percentage was reduced to 27% by incorporating NAC in the resin, which was the level equivalent to that in the culture on polystyrene. The culture on the untreated resin was found to be negative for alkaline phosphate (ALP) activity at days 5 and 10 or von Kossa mineralized nodule formation at day 20. In contrast, some areas of the cultures on NAC-incorporated resin substrates were ALP and von Kossa positive. Collagen I and dentin sialoprotein genes were barely expressed in day 7 culture on the untreated resin. However, those genes were expressed in the culture on the resin with NAC. These results suggest that the decreased cell viability and the nearly completely suppressed odontoblast-like cell phenotype of dental pulp cells cultured on PMMA dental resin can be salvaged to a biologically significant degree by the incorporation of NAC in the resin.

  12. Conjugation of diisocyanate side chains to dimethacrylate reduces polymerization shrinkage and increases the hardness of composite resins.

    Science.gov (United States)

    Jan, Yih-Dean; Lee, Bor-Shiunn; Lin, Chun-Pin; Tseng, Wan-Yu

    2014-04-01

    Polymerization shrinkage is one of the main causes of dental restoration failure. This study tried to conjugate two diisocyanate side chains to dimethacrylate resins in order to reduce polymerization shrinkage and increase the hardness of composite resins. Diisocyanate, 2-hydroxyethyl methacrylate, and bisphenol A dimethacrylate were reacted in different ratios to form urethane-modified new resin matrices, and then mixed with 50 wt.% silica fillers. The viscosities of matrices, polymerization shrinkage, surface hardness, and degrees of conversion of experimental composite resins were then evaluated and compared with a non-modified control group. The viscosities of resin matrices increased with increasing diisocyanate side chain density. Polymerization shrinkage and degree of conversion, however, decreased with increasing diisocyanate side chain density. The surface hardness of all diisocyanate-modified groups was equal to or significantly higher than that of the control group. Conjugation of diisocyanate side chains to dimethacrylate represents an effective means of reducing polymerization shrinkage and increasing the surface hardness of dental composite resins. Copyright © 2012. Published by Elsevier B.V.

  13. The effect of a leucite-containing ceramic filler on the abrasive wear of dental composites.

    Science.gov (United States)

    Atai, Mohammad; Yassini, Esmaeil; Amini, Maryam; Watts, David C

    2007-09-01

    The aim of this study was to evaluate abrasive wear of a dental composite based on a leucite-containing (KAlSi2O2 ceramic filler, and to compare it with the wear of a composite based on commonly used aluminum barium silicate glass filler. IPS Empress (Ivoclar-Vivadent) ingots were ball milled, passed through an 800 mesh (ASTM) sieve, and used as the leucite ceramic filler. Experimental composites were prepared by mixing the silane-treated fillers with the resin monomers. The resin consisted of 70 wt% Bis-GMA and 30 wt% TEGDMA containing camphorquinone and DMAEMA as the photoinitiator system. Glass-based composites were also prepared using silane-treated aluminum barium silicate glass fillers and the same resin system. TetricCeram, a commercially available dental composite, was used as control. Spherical specimens of the composites were then prepared and kept in water for 2 weeks to reach equilibrium with water. An abrasive wear test was performed using a device designed in our laboratory and weight loss of the specimens was measured as an abrasion parameter after each 50 h. SEMs were taken from worn and fractured surfaces. Degree-of-conversion of the composites was measured using FTIR spectroscopy. Vickers surface microhardness, flexural strength, and flexural modulus of the composites were also measured. The data were analyzed and compared using ANOVA and Tukey HSD tests (significance level=0.05). The results showed that there were significant differences among the abrasive wear of the composites (pwear resistance of leucite-based composite could be related to its higher surface hardness. Using leucite-containing glass as an alternative for aluminum barium silicate glass fillers in dental composites generated a significant increase in the wear resistance of the resin composites which should be beneficial in the development of dental materials.

  14. Biocompatibility of 4-META/MMA-TBB resin used as a dental luting agent.

    Science.gov (United States)

    Nakagawa, Kaori; Saita, Makiko; Ikeda, Takayuki; Hirota, Makoto; Park, Wonhee; Lee, Masaichi Chang-Il; Ogawa, Takahiro

    2015-07-01

    The bonding and biological properties of currently used luting/cementing materials need to be improved. 4-Acryloyloxyethyl trimellitate anhydride/methyl methacrylate-tri-n-butylborane (4-META/MMA-TBB) resin is primarily used for splinting mobile teeth or treating fractured teeth. It undergoes moisture-resistant polymerization and bonds strongly to dentin and metals. The purpose of this in vitro study was to compare the biological and biochemical properties META/MMA-TBB resin with those of conventional polymethyl methacrylate (PMMA)-MMA resin and other currently used luting materials in order to determine whether it may be a viable dental luting agent. The degree of polymerization of 4-META/MMA-TBB resin, PMMA-MMA autopolymerizing resin, 10-methacryloyloxydecyl dihydrogen phosphate-dimethacrylate (MDP-DMA) adhesive resin, and a glass ionomer cement was measured by Fourier-transformed infrared spectroscopy. Free radical production during setting was evaluated by electron spin resonance (ESR) spectroscopy. Rat dental pulp cells cultured on these materials were examined for cell viability, attachment, proliferation, and functional phenotype. The degree of polymerization of 4-META/MMA-TBB resin was 82% thirty minutes after preparation, compared to 66% for PMMA-MMA autopolymerizing resin. ESR spectroscopy revealed free radical production from 4-META/MMA-TBB resin and glass ionomer cement was equivalent 24 hours after preparation, with no spike in radical generation observed. In contrast, free radical production from PMMA-MMA and MDP-DMA adhesive resins was rapid and sustained and 10 to 20 times greater than that from 4-META/MMA-TBB. The percentage of viable dental pulp cells 24 hours after seeding was considerably higher on MDP-DMA and 4-META/MMA-TBB resin than on glass ionomer cement. Cell number, proliferation, and alkaline phosphatase activity were highest on 4-META/MMA-TBB resin and lowest on the glass ionomer cement. 4-META/MMA-TBB resin is at least as biocompatible

  15. The interaction between lining materials and composite resin restorative materials.

    Science.gov (United States)

    Lingard, G L; Davies, E H; Von Fraunhofer, J A

    1981-03-01

    The effects of four lining materials, Dycal, Procal, Cavitec and Poly F cement on Adaptic and Concise have been investigated in vitro. The parameters studied were surface roughness, hardness and colour both with and without an intermediate (or bonding) resin being present between the restorative material and the liner. The effects of the four liners on the composites varied both between the lining materials themselves and with the composite resin. Two materials, Procal and Dycal, had little interaction with the composites, provided an intermediate resin was used with the latter. Cavitec appeared to have an adverse reaction with the composites and Poly F, whilst having no effect on the colour of the composites, did increase surface roughness. The adverse effects of linig materials were ascribed to minor constituents, particularly methyl salicylate, present in the formulation.

  16. Comparison of Mechanical Properties of Resin Composites with Resin Modified Glass Ionomers

    Directory of Open Access Journals (Sweden)

    Taha NA

    2015-06-01

    Full Text Available Statement of Problem: There are controversial reports regarding physical and mechanical properties of resin composites and glass ionomer cements. Some revealed higher strength and hardness for resin composites while others showed a comparable value for glass ionomer cements. Evaluation of mechanical properties of different types of resin composites in comparison with resin modified glass ionomers is not widely studied. Objectives: To measure and compare the flexural strength and Vickers hardness of three resin composites and two resins modified glass ionomer cements before and after ageing. Materials and Methods: Three resin composites, i.e. Filtek Supreme XTE (3M ESPE, Ice (SDI, Gradia (GC, and two resins modified glass ionomers, i.e. Fuji II LC (GC and Riva Light Cure (SDI, were selected. Ten barshaped specimens were prepared for each material and cured using LED curing light. After 24 hours storage in distilled water at 37oC, the specimens were randomly divided into two equal groups (n=5. The first group was tested as a baseline and the second group was restored at 37oC for another 29 days. Flexural strength was performed by four-point bending test using universal testing machine at crosshead speed of 0.5mm/min, and the maximum load at failure was recorded. The specimen’s halves were used for evaluating Vickers hardness, using a Digital Hardness Tester (300 g/15 sec and the Vickers hardness number (VHN was recorded. Data were analyzed using one-way analysis of variance (ANOVA, Tukey’s and student’s t-test. Results: After 24 hours of immersion, the highest hardness number was found for Filtek Supreme and Ice and the highest flexural strength was obtained for Gradia. After 30 days of storage, hardness of Fuji II LC and Gradia showed a significant decrease; flexural strength of Ice and Fuji II LC revealed a significant increase while Gradia and Filtek Supreme showed a significant decrease. Conclusions: Resin modified glass ionomers showed

  17. Analysis of surface hardness of artificially aged resin composites

    Directory of Open Access Journals (Sweden)

    Denise Cremonezzi Tornavoi

    2012-02-01

    Full Text Available This study evaluated the effect of artificially accelerated aging (AAA on the surface hardness of eight composite resins: Filtek Z250, Filtek Supreme, 4 Seasons, Herculite, P60, Tetric Ceram, Charisma, and Filtek Z100. Sixteen specimens were made from the test piece of each material, using an 8.0 × 2.0 mm teflon matrix. After 24 hours, eight specimens from each material were submitted to three surface hardness readings using a Shimadzu Microhardness Tester for 5 seconds at a load of 50 gf. The other eight specimens remained in the artificially accelerated aging machine for 382 hours and were submitted to the same surface hardness analysis. The means of each test specimen were submitted to the Kolmogorov-Smirnov test (p > 0.05, ANOVA and Tukey test (p < 0.05. With regard to hardness (F = 86.74, p < 0.0001 the analysis showed significant differences among the resin composite brands. But aging did not influence the hardness of any of the resin composites (F = 0.39, p = 0.53. In this study, there was interaction between the resin composite brand and the aging factors (F = 4.51, p < 0.0002. It was concluded that notwithstanding the type of resin, AAA did not influence surface hardness. However, with regard to hardness there was a significant difference among the resin brands.

  18. Resin composite blocks via high-pressure high-temperature polymerization.

    Science.gov (United States)

    Nguyen, Jean-François; Migonney, Véronique; Ruse, N Dorin; Sadoun, Michaël

    2012-05-01

    The aim of this study was to thermo-polymerize under high pressure four commercially available dental resin composites to obtain and characterize composite blocks suitable for CAD/CAM procedures. Gradia (GC, Japan), Vita VM LC (Vita Zahnfabrik, Germany), Grandio (VOCO, Germany), and EsthetX (Dentsply, Germany), were selected for this study. Paradigm (3 M ESPE, USA), a CAD/CAM composite block, was included for comparison. Composite blocks were obtained through polymerization at high-temperature high-pressure (HT/HP). Samples for mechanical/physical characterizations were cut from Paradigm and HT/HP composite blocks while control samples were obtained by photo-polymerizing (PP) the materials in molds. Flexural strength (σ(f)), fracture toughness (K(IC)), hardness, and density (ρ) were determined and compared by pairwise t-tests (α=0.05). Fractured surfaces were characterized under a scanning electron microscope. The results have shown that HT/HP polymerization resulted in a significant (p<0.05) increase in σ(f), hardness, and ρ for all composites investigated. Even if K(IC) of all materials was increased by HT/HP polymerization, significant increases were detected only for Gradia and EsthetX. The Weibull modulus of HT/HP polymerized composites was higher than that of PP counterparts. HT/HP materials had higher σ(f), Weibull modulus, and K(IC) compared to Paradigm. The most significant SEM observation of fractured K(IC) specimens from all the materials tested was the presence of fewer and smaller voids in HT/HP polymerized composites. The results of this study suggest that HT/HP polymerization could be used to obtain dental resin composite blocks with superior mechanical properties, suitable for CAD/CAM processing. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  19. Reducing composite restoration polymerization shrinkage stress through resin modified glass-ionomer based adhesives.

    Science.gov (United States)

    Naoum, S J; Mutzelburg, P R; Shumack, T G; Thode, Djg; Martin, F E; Ellakwa, A E

    2015-12-01

    The aim of this study was to determine whether employing resin modified glass-ionomer based adhesives can reduce polymerization contraction stress generated at the interface of restorative composite adhesive systems. Five resin based adhesives (G Bond, Optibond-All-in-One, Optibond-Solo, Optibond-XTR and Scotchbond-Universal) and two resin modified glass-ionomer based adhesives (Riva Bond-LC, Fuji Bond-LC) were analysed. Each adhesive was applied to bond restorative composite Filtek-Z250 to opposing acrylic rods secured within a universal testing machine. Stress developed at the interface of each adhesive-restorative composite system (n = 5) was calculated at 5-minute intervals over 6 hours. The resin based adhesive-restorative composite systems (RBA-RCS) demonstrated similar interface stress profiles over 6 hours; initial rapid contraction stress development (0-300 seconds) followed by continued contraction stress development ≤0.02MPa/s (300 seconds - 6 hours). The interface stress profile of the resin modified glass-ionomer based adhesive-restorative composite systems (RMGIBA-RCS) differed substantially to the RBA-RCS in several ways. Firstly, during 0-300 seconds the rate of contraction stress development at the interface of the RMGIBA-RCS was significantly (p glass-ionomer based adhesives can significantly reduce the magnitude and rate of polymerization contraction stress developed at the interface of adhesive-restorative composite systems. © 2015 Australian Dental Association.

  20. Resin bond to indirect composite and new ceramic/polymer materials: a review of the literature.

    Science.gov (United States)

    Spitznagel, Frank A; Horvath, Sebastian D; Guess, Petra C; Blatz, Markus B

    2014-01-01

    Resin bonding is essential for clinical longevity of indirect restorations. Especially in light of the increasing popularity of computer-aided design/computer-aided manufacturing-fabricated indirect restorations, there is a need to assess optimal bonding protocols for new ceramic/polymer materials and indirect composites. The aim of this article was to review and assess the current scientific evidence on the resin bond to indirect composite and new ceramic/polymer materials. An electronic PubMed database search was conducted from 1966 to September 2013 for in vitro studies pertaining the resin bond to indirect composite and new ceramic/polymer materials. The search revealed 198 titles. Full-text screening was carried out for 43 studies, yielding 18 relevant articles that complied with inclusion criteria. No relevant studies could be identified regarding new ceramic/polymer materials. Most common surface treatments are aluminum-oxide air-abrasion, silane treatment, and hydrofluoric acid-etching for indirect composite restoration. Self-adhesive cements achieve lower bond strengths in comparison with etch-and-rinse systems. Thermocycling has a greater impact on bonding behavior than water storage. Air-particle abrasion and additional silane treatment should be applied to enhance the resin bond to laboratory-processed composites. However, there is an urgent need for in vitro studies that evaluate the bond strength to new ceramic/polymer materials. This article reviews the available dental literature on resin bond of laboratory composites and gives scientifically based guidance for their successful placement. Furthermore, this review demonstrated that future research for new ceramic/polymer materials is required. © 2014 Wiley Periodicals, Inc.

  1. Photothermal radiometric determination of thermal diffusivity depth profiles in a dental resin

    International Nuclear Information System (INIS)

    MartInez-Torres, P; Alvarado-Gil, J J; Mandelis, A

    2010-01-01

    The depth of curing due to photopolymerization in a commercial dental resin is studied using photothermal radiometry. The sample consists of a thick layer of resin on which a thin metallic layer is deposited guaranteeing full opacity of the sample. In this case, purely thermal-wave inverse problem techniques without the interference of optical profiles can be used. Thermal profiles are obtained by heating the coating with a modulated laser beam and performing a modulation frequency scan. Before each frequency scan, photopolymerization was induced using a high power blue LED. However due to the fact that dental resins are highly light dispersive materials, the polymerization process depends strongly on the optical absorption coefficient inducing a depth dependent thermal diffusion in the sample. It is shown that using a robust depth profilometric inverse method one can reconstruct the thermal diffusivity profile of the photopolymerized resin.

  2. Adhesive system affects repair bond strength of resin composite

    OpenAIRE

    Irmak, Ozgur; Celiksoz, Ozge; Yilmaz, Begum; Yaman, Batu Can

    2017-01-01

    Purpose: This study evaluated the effects of different adhesive systems on repair bond strength of aged resin composites. Materials and Methods: Ninety composite discs were built and half of them were subjected to thermal aging. Aged and non-aged specimens were repaired with resin composite using three different adhesive systems; a two-step self-etch adhesive, a two-step total-etch adhesive and a one-step self-etch adhesive; then they were subjected to shear forces. Data were analyzed stat...

  3. Cosmetic Remodeling of the Smile: Combining Composite Resin and Ceramics over Teeth and Implants

    Directory of Open Access Journals (Sweden)

    Leonardo Fernandes da Cunha

    2017-01-01

    Full Text Available The aim of this paper is to describe a restorative approach to the cosmetic remodeling of the teeth of a young adult patient with right maxillary lateral hypodontia and left lateral microdontia. A conservative restorative management was proposed to improve smile esthetics by combining direct composite resins and ceramics. Initially, periodontal therapy and dental bleaching were performed. Subsequently, direct composite resins were applied to the central incisors and canines to reestablish the sizes and shapes of these teeth. Finally, ceramics were placed on the implant and the microdontia to unite with the new alignment and color of the anterior teeth. Thus, conservative remodeling to improve the harmony of the smile was provided.

  4. Synthesis of nanosized barium titanate/epoxy resin composites and ...

    Indian Academy of Sciences (India)

    Anechoic chamber; barium titanate; electromagnetic interference and compatibility; epoxy resin composites; microwave absorbers; radio frequency absorbers. ... The reflection loss (RL) and transmission loss (TL) of the composite materials were measured by the reflection/transmission method using a vector network ...

  5. [Water absorption of five dental resins used in bonded restorations].

    Science.gov (United States)

    Gillet, D; Dupuis, V

    2002-12-01

    The actual restorative dentistry need to bond material which are under the constraint of saliva likely, as all liquid, to enter inside the product with time and to modify its characteristics. In this study, we compare the behaviour of five materials opposite water absorption, in vitro, until one year: two composite resins (Tetric et Pertac II), two ceromer (ceromer (Tetric ceram et Tetric flow) and one compomer (Hytac(r)). Each pastille weight is expressed in percentage of initial weight. All materials loose weight in the first hours except Tetric ceram which stay stable. At 48 h, all materials except Pertac II get back their initial weight. At long-term, all the materials are stable with a profit of 1% for Hytac, 0.5% for Tetric, Tetric ceram et Tetric flow and a loss of à 0.3% for Pertac II. As a result of this study, we understand why the clinical used of Hytac must be done following strict conditions.

  6. Wear of human enamel opposing monolithic zirconia, glass ceramic, and composite resin: an in vitro study.

    Science.gov (United States)

    Sripetchdanond, Jeerapa; Leevailoj, Chalermpol

    2014-11-01

    Demand is increasing for ceramic and composite resin posterior restorations. However, ceramics are recognized for their high abrasiveness to opposing dental structure. The purpose of this study was to investigate the wear of enamel as opposed to dental ceramics and composite resin. Twenty-four test specimens (antagonists), 6 each of monolithic zirconia, glass ceramic, composite resin, and enamel, were prepared into cylindrical rods. Enamel specimens were prepared from 24 extracted human permanent molar teeth. Enamel specimens were abraded against each type of antagonist with a pin-on-disk wear tester under a constant load of 25 N at 20 rpm for 4800 cycles. The maximum depth of wear (Dmax), mean depth of wear (Da), and mean surface roughness (Ra) of the enamel specimens were measured with a profilometer. All data were statistically analyzed by 1-way ANOVA, followed by the Tukey test (α=.05). A paired t test was used to compare the Ra of enamel at baseline and after testing. The wear of both the enamel and antagonists was evaluated qualitatively with scanning electron microscopic images. No significant differences were found in enamel wear depth (Dmax, Da) between monolithic zirconia (2.17 ±0.80, 1.83 ±0.75 μm) and composite resin (1.70 ±0.92, 1.37 ±0.81 μm) or between glass ceramic (8.54 ±2.31, 7.32 ±2.06 μm) and enamel (10.72 ±6.31, 8.81 ±5.16 μm). Significant differences were found when the enamel wear depth caused by monolithic zirconia and composite resin was compared with that of glass ceramic and enamel (Pglass ceramic, and enamel (Pglass ceramic and enamel. All test materials except composite resin similarly increased the enamel surface roughness after wear testing. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  7. Antibacterial effect of composite resins containing quaternary ammonium polyethyleneimine nanoparticles

    International Nuclear Information System (INIS)

    Yudovin-Farber, Ira; Beyth, Nurit; Weiss, Ervin I.; Domb, Abraham J.

    2010-01-01

    Quaternary ammonium polyethyleneimine (QA-PEI)-based nanoparticles were synthesized by crosslinking with dibromopentane followed by N-alkylation with various alkyl halides and further N-methylation with methyl iodide. Insoluble pyridinium-type particles were prepared by suspension polymerization of 4-vinyl pyridine followed by N-alkylation with alkyl halides. Polyamine-based nanoparticles embedded in restorative composite resin at 1% w/w were tested for antibacterial activity against Streptococcus mutans using direct contact test. Activity analysis revealed that the alkyl chain length of the QA-PEI nanoparticles plays a significant role in antibacterial activity of the reagent. The most potent compound was octyl-alkylated QA-PEI embedded in restorative composite resin at 1% w/w that totally inhibited S. mutans growth in 3-month-aged samples. This data indicates that restorative composite resin with antibacterial properties can be produced by the incorporation of QA-PEI nanoparticles.

  8. Antibacterial effect of composite resins containing quaternary ammonium polyethyleneimine nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Yudovin-Farber, Ira [Hebrew University of Jerusalem, Department of Medicinal Chemistry and Natural Products, School of Pharmacy, Faculty of Medicine (Israel); Beyth, Nurit; Weiss, Ervin I. [Hebrew University of Jerusalem, Department of Prosthodontics, Faculty of Dentistry (Israel); Domb, Abraham J., E-mail: avid@ekmd.huji.ac.i [Hebrew University of Jerusalem, Department of Medicinal Chemistry and Natural Products, School of Pharmacy, Faculty of Medicine (Israel)

    2010-02-15

    Quaternary ammonium polyethyleneimine (QA-PEI)-based nanoparticles were synthesized by crosslinking with dibromopentane followed by N-alkylation with various alkyl halides and further N-methylation with methyl iodide. Insoluble pyridinium-type particles were prepared by suspension polymerization of 4-vinyl pyridine followed by N-alkylation with alkyl halides. Polyamine-based nanoparticles embedded in restorative composite resin at 1% w/w were tested for antibacterial activity against Streptococcus mutans using direct contact test. Activity analysis revealed that the alkyl chain length of the QA-PEI nanoparticles plays a significant role in antibacterial activity of the reagent. The most potent compound was octyl-alkylated QA-PEI embedded in restorative composite resin at 1% w/w that totally inhibited S. mutans growth in 3-month-aged samples. This data indicates that restorative composite resin with antibacterial properties can be produced by the incorporation of QA-PEI nanoparticles.

  9. Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin

    International Nuclear Information System (INIS)

    Yap, A.U.J.

    1997-01-01

    This study examined the post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin using a digital microhardness tester. Change in hardness of these materials over a period of 6 months was compared to that of conventional glass ionomer cements and a composite resin. With the exception of the composite resin, all materials showed a significant increase in hardness over 24 h after their initial set. Dual-cure resin-modified glass ionomer cements showed decreased hardness with increased storage time in saline at 37 o C. Results suggest that the addition of resins to glass ionomer cements does not improve initial hardness and does not negate the acid-base reaction of conventional cements. Resin addition may, however, lead to increased water sorption and decreased hardness. (author)

  10. Class II composite resin restorations: faster, easier, predictable.

    Science.gov (United States)

    Jackson, R D

    2016-11-18

    Composite resin continues to displace amalgam as the preferred direct restorative material in developed countries. Even though composite materials have evolved to include nanoparticles with high physical properties and low shrinkage stress, dentists have been challenged to efficiently create quality, long lasting, predictable restorations. Unlike amalgam, composite resin cannot be condensed making the establishment of a predictable, proper contact more difficult. In addition, composite requires an understanding of adhesives and an appreciation for their exacting application. These facts combined with the precise adaptation and light-curing of multiple layers makes placement of quality Class II composite restorations tedious and time-consuming. For private practicing dentists, it can also have an effect on economic productivity. Clinicians have always wanted an easier, efficient placement technique for posterior composite restorations that rivals that for amalgam. It appears that advances in instrumentation, materials and technology have finally delivered it.

  11. Ultraviolet light and ultraviolet light-activated composite resins

    International Nuclear Information System (INIS)

    Murray, G.A.; Yates, J.L.; Newman, S.M.

    1981-01-01

    In a comparison of the UV light--activated composite resins, Estilux was polymerized to a significantly greater depth than the other composite resins. In general, Lee-fill polymerized the least. When comparing the UV light sources, the Lee light and the Duralux light did not significantly differ from each other, but both polymerized the materials tested to a significantly greater depth than the other light sources. Of the two time exposures, 60-second exposure provided a significantly greater depth of polymerization than 20 seconds for each light with each material

  12. Graphene Oxide and Thermally Exfoliated Graphene Cyanate Ester Resin Composites

    Science.gov (United States)

    2013-05-01

    arranged in a honey -comb lattice, its high surface to volume ratio allows property improvements at lower weight fractions than other composite fillers...Resin Composites 5a. CONTRACT NUMBER In-House 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Josiah T. Reams, Kevin R. Lamison...materials for space and propulsion applications have brought attention to the need for high temperature composite materials with improved stiffness

  13. Benzoxazine resin/carbon nanotube nanostructured composite's degradation kinetic.

    Science.gov (United States)

    Untem, Flávia O; Botelho, Edson C; Rezende, Mirabel C; Costa, Michelle Leali

    2014-07-01

    In the last decades a new class of thermoset phenolic resin is emerging as a substitute of the traditional epoxy and phenolic resins in the aircraft industry. This new class is called polybenzoxazines and its associates the epoxy resin's mechanical properties and phenolic resin's thermal and flame retardant properties, resulting in a resin with superior properties when analyzed with the others singly. The introduction of carbon nanotubes in low concentration into polymeric matrices can produce nanostructured materials with good properties. Thus, in this study, nanostructured composites of benzoxazine resin were processed with different concentration of carbon nanotubes (0.1%, 0.5% and 1.0% w/w). In order to evaluate the thermostability of the benzoxazine resin and its nanostructured composites, it was performed a degradation kinetic study using the thermogravimetric technique. For that, the analysis have been done with the temperature ranging from 25 degrees C to 1000 degrees C at nitrogen atmosphere (100 mL x min(-1)) and in different heating rates (2, 4, 6, 8, 10 and 20 degrees C x min(-1)), in order to obtain the kinetic parameters (activation energy, E(a), and pre-exponential factor, A), based on Ozawa-Wall-Flynn model. The results showed excellent agreement between the thermogravimetric curves obtained and the Ozawa-Wall-Flynn method. The degradation kinetic study showed that the introduction of carbon nanotubes in the benzoxazine matrix does not change the thermostability of the resin, so that it does not have a significant influence in the shelf life of the material.

  14. [Comparative study of polymerization shrinkage and related properties of flowable composites and an unfilled resin].

    Science.gov (United States)

    Bukovinszky, Katalin; Molnár, Lilla; Bakó, József; Szalóki, Melinda; Hegedus, Csaba

    2014-03-01

    The polymerization shrinkage and shrinkage stress of dental composites are in the center of the interest of researchers and manufacturers. It is a great challenge to minimize this important property as low as possible. Many factors are related and are in complicated correlation with each other affecting the polymerization shrinkage. Polymerization shrinkage stress degree of conversion and elasticity has high importance from this aspect. Our aim was to study the polymerization shrinkage and related properties (modulus of elasticity, degree of conversion, shrinkage stress) of three flowable composite (Charisma Opal Flow, SDR, Filtek Ultimate) and an unfilled composite resin. Modulus of elasticity was measured using three point flexure tests on universal testing machine. The polymerization shrinkage stress was determined using bonded-disc technique. The degree of conversion measurements were performed by FT-IR spectroscopy. And the volumetric shrinkage was investigated using Archimedes principle and was measured on analytical balance with special additional equipment. The unfilled resin generally showed higher shrinkage (8,26%), shrinkage stress (0,8 MPa) and degree of conversion (38%), and presented the lowest modulus of elasticity (3047,02MPa). Highest values of unfilled resin correspond to the literature. The lack of fillers enlarges the shrinkage, and the shrinkage stress, but gives the higher flexibility and higher degree of conversion. Further investigations needs to be done to understand and reveal the differences between the composites.

  15. Surface Modified Characteristics of the Tetracalcium Phosphate as Light-Cured Composite Resin Fillers

    Directory of Open Access Journals (Sweden)

    Wen-Cheng Chen

    2014-01-01

    Full Text Available The objectives of this study are to characterize the properties of light-cured composite resins that are reinforced with whisker surface-modified particles of tetracalcium phosphate (TTCP and to investigate the influence of thermal cycling on the reinforced composites properties. The characteristics of ultimate diametral tensile strength (DTS, moduli, pH values, and fracture surfaces of the samples with different amounts of surface-modified TTCP (30%–60% were determined before and after thermal cycling between 5°C and 55°C in deionized water for 600 cycles. The trends of all groups were ductile prior to thermal cycling and the moduli of all groups increased after thermal cycling. The ductile property of the control group without filler was not significantly affected. Larger amounts of fillers caused the particles to aggregate, subsequently decreasing the resin’s ability to disperse external forces and leading to brittleness after thermal cycling. Therefore, the trend of composite resins with larger amounts of filler would become more brittle and exhibited higher moduli after thermal cycling. This developed composite resin with surface modified-TTCP fillers has the potential to be successful dental restorative materials.

  16. Fatigue Resistance of CAD/CAM Resin Composite Molar Crowns

    Science.gov (United States)

    Shembish, Fatma A.; Tong, Hui; Kaizer, Marina; Janal, Malvin N.; Thompson, Van P.; Opdam, Niek J.; Zhang, Yu

    2016-01-01

    Objective To demonstrate the fatigue behavior of CAD/CAM resin composite molar crowns using a mouth-motion step-stress fatigue test. Monolithic leucite-reinforced glass-ceramic crowns were used as a reference. Methods Fully anatomically shaped monolithic resin composite molar crowns (Lava Ultimate, n = 24) and leucite reinforced glass-ceramic crowns (IPS Empress CAD, n = 24) were fabricated using CAD/CAM systems. Crowns were cemented on aged dentin-like resin composite tooth replicas (Filtek Z100) with resin-based cements (RelyX Ultimate for Lava Ultimate or Multilink Automix for IPS Empress). Three step-stress profiles (aggressive, moderate and mild) were employed for the accelerated sliding-contact mouth-motion fatigue test. Twenty one crowns from each group were randomly distributed among these three profiles (1:2:4). Failure was designated as chip-off or bulk fracture. Optical and electronic microscopes were used to examine the occlusal surface and subsurface damages, as well as the material microstructures. Results The resin composite crowns showed only minor occlusal damage during mouth-motion step-stress fatigue loading up to 1700 N. Cross-sectional views revealed contact-induced cone cracks in all specimens, and flexural radial cracks in 2 crowns. Both cone and radial cracks were relatively small compared to the crown thickness. Extending these cracks to the threshold for catastrophic failure would require much higher indentation loads or more loading cycles. In contrast, all of the glass-ceramic crowns fractured, starting at loads of approximately 450 N. Significance Monolithic CAD/CAM resin composite crowns endure, with only superficial damage, fatigue loads 3 – 4 times higher than those causing catastrophic failure in glass-ceramic CAD crowns. PMID:26777092

  17. Anterior Cantilever Resin-Bonded Fixed Dental Prostheses: A Review of the Literature.

    Science.gov (United States)

    Mourshed, Bilal; Samran, Abdulaziz; Alfagih, Amal; Samran, Ahalm; Abdulrab, Saleem; Kern, Matthias

    2018-03-01

    This review evaluated the survival rate of single retainer anterior resin-bonded fixed dental prostheses (RBFDPs) to determine whether the choice of material affects their clinical outcome. An electronic search of the English peer-reviewed dental literature in PubMed was conducted to identify all publications reporting on cantilever RBFDPs until May 2016. Study information extraction and methodological quality assessments were accomplished by two reviewers independently. The searched keywords were as follows: "resin-bonded, single retainer, all-ceramic resin-bonded fixed dental prostheses (RBFDPs), all-ceramic RBFDPs, cantilever resin, RBFDPs, cantilever resin-bonded bridge, two units cantilevered, two-unit cantilevered, metal-ceramic cantilever, and metal-ceramic." Furthermore, the ''Related Articles'' feature of PubMed was used to identify further references of interest within the primary search. The bibliographies of the obtained references were used to identify pertinent secondary references. Review articles were also used to identify relevant articles. After the application of exclusion criteria, the definitive list of articles was screened to extract the qualitative data, and the results were analyzed. Overall 2588 articles were dedicated at the first review phase; however, only 311 studies were left after the elimination of duplicates and unrelated studies. Seventeen studies passed the second review phase. Five studies were excluded because they were follow-up studies of the same study cohort. Twelve studies were finally selected. The use of cantilever RBFDPs showed promising results and high survival rates. © 2016 by the American College of Prosthodontists.

  18. Cell death effects of resin-based dental material compounds and mercurials in human gingival fibroblasts

    Energy Technology Data Exchange (ETDEWEB)

    Reichl, Franz-Xaver [Walther-Straub-Institute of Pharmacology and Toxicology, Munich (Germany); Ludwig-Maximilians-University, Department of Operative Dentistry and Periodontology, Munich (Germany); Esters, Magali; Simon, Sabine; Seiss, Mario [Walther-Straub-Institute of Pharmacology and Toxicology, Munich (Germany); Kehe, Kai [Bundeswehr Institute of Pharmacology and Toxicology, Munich (Germany); Kleinsasser, Norbert [University of Regensburg, Head and Neck Surgery, Department of Otolaryngology, Regensburg (Germany); Folwaczny, Matthias; Glas, Juergen; Hickel, Reinhard [Ludwig-Maximilians-University, Department of Operative Dentistry and Periodontology, Munich (Germany)

    2006-06-15

    In order to test the hypothesis that released dental restorative materials can reach toxic levels in human oral tissues, the cytotoxicities of the resin-based dental (co)monomers hydroxyethylmethacrylate (HEMA), triethyleneglycoldimethacrylate (TEGDMA), urethanedimethacrylate (UDMA), and bisglycidylmethacrylate (BisGMA) compared with methyl mercury chloride (MeHgCl) and the amalgam component mercuric chloride (HgCl{sub 2}) were investigated on human gingival fibroblasts (HGF) using two different test systems: (1) the modified XTT-test and (2) the modified H 33342 staining assay. The HGF were exposed to various concentrations of the test-substances in all test systems for 24 h. All tested (co)monomers and mercury compounds significantly (P<0.05) decreased the formazan formation in the XTT-test. EC{sub 50} values in the XTT assay were obtained as half-maximum-effect concentrations from fitted curves. Following EC{sub 50} values were found (mean [mmol/l]; s.e.m. in parentheses; n=12; * significantly different to HEMA): HEMA 11.530 (0.600); TEGDMA* 3.460 (0.200); UDMA* 0.106 (0.005); BisGMA* 0.087 (0.001); HgCl{sub 2}* 0.013 (0.001); MeHgCl* 0.005 (0.001). Following relative toxicities were found: HEMA 1; TEGDMA 3; UDMA 109; BisGMA 133; HgCl{sub 2} 887; MeHgCl 2306. A significant (P<0.05) increase of the toxicity of (co)monomers and mercurials was found in the XTT-test in the following order: HEMA < TEGDMA < UDMA < BisGMA < HgCl{sub 2} < MeHgCl. TEGDMA and MeHgCl induced mainly apoptotic cell death. HEMA, UDMA, BisGMA, and HgCl{sub 2} induced mainly necrotic cell death. The results of this study indicate that resin composite components have a lower toxicity than mercury from amalgam in HGF. HEMA, BisGMA, UDMA, and HgCl{sub 2} induced mainly necrosis, but it is rather unlikely that eluted substances (solely) can reach concentrations, which might induce necrotic cell death in the human physiological situation, indicating that other (additional) factors may be involved in

  19. Interactions of self-etch adhesives with resin composites.

    Science.gov (United States)

    Kurokawa, Rie; Finger, Werner J; Hoffmann, Marcus; Endo, Tatsuo; Kanehira, Masafumi; Komatsu, Masashi; Manabe, Atsufumi

    2007-12-01

    Aim of this in vitro study was to investigate the correlation of shear bond strength and marginal cavity adaptation, together with polymerization shrinkage and contraction stress, using the combination of four self-etch adhesives and three resin composites. Interactions were studied between one two-step and three one-step adhesives, and the hybrid-type resin composites, Beautifil (BEU, Shofu) and Venus (VEN, Heraeus), and an experimental nano-hybrid resin composite NEUN (NEU, Heraeus). For all 12 combinations shear bond strengths (SBS) were determined on human dentin. Marginal adaptation (MGW) was assessed in cylindrical butt-joint dentin cavities. Further, polymerization contraction and contraction stress of the resin restoratives were measured. Significant determinants of SBSs on dentin were time of testing (10min or 24h) and adhesives (presin composite used was a highly significant determinant of cavity adaptation. Polymerization shrinkage after 5min was 2.58, 2.74, and 1.53% for BEU, VEN, and NEU, respectively. Polymerization contraction stresses were largest for BEU, less for VEN, and smallest for NEU (presin composites were identified as important determinants of marginal cavity adaptation.

  20. Depth of cure of bulk-fill flowable composite resins.

    Science.gov (United States)

    Pedalino, Inaam; Hartup, Grant R; Vandewalle, Kraig S

    2015-01-01

    In recent years, manufacturers have introduced flowable composite resins that reportedly can be placed in increments of 4 mm or greater. The purpose of this study was to evaluate the depth of cure of bulk-fill flowable composite resins (SureFil SDR Flow, Grandio Flow, and Venus Bulk Fill) and a conventional flowable composite resin (Revolution Formula 2). Depth of cure was measured in terms of bottom-maximum Knoop hardness number (KHN) ratios and the International Organization for Standardization (ISO) 4049 scrape technique. Shades A2 and A3 of SureFil SDR Flow, Grandio Flow, and Revolution Formula 2 were tested. Venus Bulk Fill was tested in its only available shade (universal). Specimens in thicknesses of 2, 3, 4, 5, and 6 mm were polymerized for 20 or 40 seconds, and a hardness tester was used to determine the hardness ratios for each shade at each thickness. For the scraping technique, after specimens were exposed to the curing light, unpolymerized composite resin was removed with a plastic instrument, the polymerized composite was measured, and the length was divided by 2 per ISO guidelines. According to the KHN ratios and the scrape test, Venus Bulk Fill predictably exceeded the manufacturer's claim of a 4-mm depth of cure at both 20 and 40 seconds of curing time. The overall results for depth of cure showed that Venus Bulk Fill ≥ SureFil SDR Flow ≥ Grandio Flow ≥ Revolution Formula 2.

  1. Effect of Ingested Liquids on Color Change of Composite Resins.

    Science.gov (United States)

    Malek Afzali, Beheshteh; Ghasemi, Amir; Mirani, Asrin; Abdolazimi, Zahra; Akbarzade Baghban, Alireza; Kharazifard, Mohammad Javad

    2015-08-01

    Color change of composite restorations is well known to dentists. However, the effect of commonly consumed drinks on discoloration of composite resins has yet to be determined. This study sought to assess the color change of a nanofilled (Premise) and a flowable composite resin (Premise flowable) following simulated consumption of tea, cola, iron drops and multivitamin syrup. Forty disk-shaped specimens (7 mm in diameter and 2 mm thick) were fabricated from each composite resin. The baseline color values were measured according to the CIE L*a*b* system using digital imaging. The specimens of each restorative material were randomly divided into five groups (eight each) according to the storage media namely tea, cola, iron drops, multivitamin syrup or distilled water (control). The specimens were immersed in staining solutions for three hours daily over a 40-day test period. Following this, the color change values (ΔE*) were calculated. For statistical analyses, the color differences were analyzed using two-way ANOVA and Tukey's test (Pcomposite resins (P>0.05). In both composite materials, the difference among the solutions was not significant (P>0.05). Under the tested experimental conditions, both restorative materials were susceptible to discoloration by all four staining solutions. The color change values were not related to the solution or the type of material used.

  2. Long-term performance of resin based fissure sealants placed in a general dental practice.

    NARCIS (Netherlands)

    Hevinga, M.A.; Opdam, N.J.M.; Bronkhorst, E.M.; Truin, G.J.; Huysmans, M.C.D.N.J.M.

    2010-01-01

    OBJECTIVES: The aim of the present retrospective study was to evaluate the long-term performance of resin based fissure sealants applied in a general dental practice. METHODS: Regularly attending patients visiting the practice between July 2006 until November 2007 and who had received sealants

  3. Confirmation of theoretical colour predictions for layering dental composite materials.

    Science.gov (United States)

    Mikhail, Sarah S; Johnston, William M

    2014-04-01

    The aim of this study is to confirm the theoretical colour predictions for single and double layers of dental composite materials on an opaque backing. Single and double layers of composite resins were fabricated, placed in optical contact with a grey backing and measured for spectral radiance. The spectral reflectance and colour were directly determined. Absorption and scattering coefficients as previously reported, the measured thickness of the single layers and the effective reflectance of the grey backing were utilized to theoretically predict the reflectance of the single layer using corrected Kubelka-Munk reflectance theory. For double layers the predicted effective reflectance of the single layer was used as the reflectance of the backing of the second layer and the thickness of the second layer was used to predict the reflectance of the double layer. Colour differences, using both the CIELAB and CIEDE2000 formulae, measured the discrepancy between each directly determined colour and its corresponding theoretical colour. The colour difference discrepancies generally ranged around the perceptibility threshold but were consistently below the respective acceptability threshold. This theory can predict the colour of layers of composite resin within acceptability limits and generally also within perceptibility limits. This theory could therefore be incorporated into computer-based optical measuring instruments that can automate the shade selections for layers of a more opaque first layer under a more translucent second layer for those clinical situations where an underlying background colour and a desirable final colour can be measured. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Electrospun nanofiber reinforcement of dental composites with electromagnetic alignment approach

    International Nuclear Information System (INIS)

    Uyar, Tansel; Çökeliler, Dilek; Doğan, Mustafa; Koçum, Ismail Cengiz; Karatay, Okan; Denkbaş, Emir Baki

    2016-01-01

    Polymethylmethacrylate (PMMA) is commonly used as a base acrylic denture material with benefits of rapid and easy handling, however, when it is used in prosthetic dentistry, fracturing or cracking problems can be seen due to the relatively low strength issues. Besides, acrylic resin is the still prominent material for denture fabrication due to its handy and low cost features. Numerous proposed fillers that are used to produce PMMA composites, however electrospun polyvinylalcohol (PVA) nanofiber fillers for production of PMMA composite resins are not studied as much as the others. The other focus of the practice is to compare both mechanical properties and efficiency of aligned fibers versus non-aligned PVA nanofibers in PMMA based dental composites. Field-controlled electrospinning system is manufactured and provided good alignment in lab scale as one of contributions. Some novel auxiliary electrodes in controlled structure are augmented to obtain different patterns of alignment with a certain range of fiber diameters. Scanning electron microscopy is used for physical characterization to determine the range of fiber diameters. Non-woven fiber has no unique pattern due to chaotic nature of electrospinning process, but aligned fibers have round pattern or crossed lines. These produced fibers are structured as layer-by-layer form with different features, and these features are used in producing PMMA dental composites with different volume ratios. The maximum flexural strength figure shows that fiber load by weight of 0.25% w/w and above improves in the maximum level. As a result, mechanical properties of PMMA dental composites are improved by using PVA nanofibers as a filler, however the improvement was higher when aligned PVA nanofibers are used. The maximum values were 5.1 MPa (flexural strength), 0.8 GPa (elastic modulus), and 170 kJ/m 3 (toughness) in three-point bending test. In addition to the positive results of aligned and non-aligned nanofibers it was found

  5. Electrospun nanofiber reinforcement of dental composites with electromagnetic alignment approach

    Energy Technology Data Exchange (ETDEWEB)

    Uyar, Tansel [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Çökeliler, Dilek, E-mail: cokeliler@baskent.edu.tr [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Doğan, Mustafa [Department of Electrical and Electronics Engineering, Başkent University, Ankara 06180 (Turkey); Koçum, Ismail Cengiz [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Karatay, Okan [Department of Electrical and Electronics Engineering, Başkent University, Ankara 06180 (Turkey); Denkbaş, Emir Baki [Department of Chemistry, Biochemistry Division, Hacettepe University, Ankara (Turkey)

    2016-05-01

    Polymethylmethacrylate (PMMA) is commonly used as a base acrylic denture material with benefits of rapid and easy handling, however, when it is used in prosthetic dentistry, fracturing or cracking problems can be seen due to the relatively low strength issues. Besides, acrylic resin is the still prominent material for denture fabrication due to its handy and low cost features. Numerous proposed fillers that are used to produce PMMA composites, however electrospun polyvinylalcohol (PVA) nanofiber fillers for production of PMMA composite resins are not studied as much as the others. The other focus of the practice is to compare both mechanical properties and efficiency of aligned fibers versus non-aligned PVA nanofibers in PMMA based dental composites. Field-controlled electrospinning system is manufactured and provided good alignment in lab scale as one of contributions. Some novel auxiliary electrodes in controlled structure are augmented to obtain different patterns of alignment with a certain range of fiber diameters. Scanning electron microscopy is used for physical characterization to determine the range of fiber diameters. Non-woven fiber has no unique pattern due to chaotic nature of electrospinning process, but aligned fibers have round pattern or crossed lines. These produced fibers are structured as layer-by-layer form with different features, and these features are used in producing PMMA dental composites with different volume ratios. The maximum flexural strength figure shows that fiber load by weight of 0.25% w/w and above improves in the maximum level. As a result, mechanical properties of PMMA dental composites are improved by using PVA nanofibers as a filler, however the improvement was higher when aligned PVA nanofibers are used. The maximum values were 5.1 MPa (flexural strength), 0.8 GPa (elastic modulus), and 170 kJ/m{sup 3} (toughness) in three-point bending test. In addition to the positive results of aligned and non-aligned nanofibers it was

  6. Development and Validation of a Constitutive Model for Dental Composites during the Curing Process

    Science.gov (United States)

    Wickham Kolstad, Lauren

    Debonding is a critical failure of a dental composites used for dental restorations. Debonding of dental composites can be determined by comparing the shrinkage stress of to the debonding strength of the adhesive that bonds it to the tooth surface. It is difficult to measure shrinkage stress experimentally. In this study, finite element analysis is used to predict the stress in the composite during cure. A new constitutive law is presented that will allow composite developers to evaluate composite shrinkage stress at early stages in the material development. Shrinkage stress and shrinkage strain experimental data were gathered for three dental resins, Z250, Z350, and P90. Experimental data were used to develop a constitutive model for the Young's modulus as a function of time of the dental composite during cure. A Maxwell model, spring and dashpot in series, was used to simulate the composite. The compliance of the shrinkage stress device was also taken into account by including a spring in series with the Maxwell model. A coefficient of thermal expansion was also determined for internal loading of the composite by dividing shrinkage strain by time. Three FEA models are presented. A spring-disk model validates that the constitutive law is self-consistent. A quarter cuspal deflection model uses separate experimental data to verify that the constitutive law is valid. Finally, an axisymmetric tooth model is used to predict interfacial stresses in the composite. These stresses are compared to the debonding strength to check if the composite debonds. The new constitutive model accurately predicted cuspal deflection data. Predictions for interfacial bond stress in the tooth model compare favorably with debonding characteristics observed in practice for dental resins.

  7. Technique for fabricating individualized dentures with a gingiva-shade composite resin.

    Science.gov (United States)

    Park, Beom-Woo; Kim, Nam-Jin; Lee, Jonghyuk; Lee, Hae-Hyoung

    2016-05-01

    More natural dental esthetics have been sought by patients who wear conventional complete or partial dentures. Recently, gingiva-shade composite resins (GSCRs) have become available for replicating soft tissue for both fixed and removable prostheses. The technique presented is for fabricating individualized complete dentures. First the acrylic resin is mixed with a coloring agent and processed to modify the base shade of the denture. GSCRs are light polymerized onto a prepared space on the buccal surfaces of denture base to replicate the appearance of gingival tissues including blood vessels. The technique provides an outstanding natural, gingiva-like, appearance and allows complete dentures to harmonize with the individual patient's surrounding oral tissues. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  8. Composite Resin – A Versatile Restorative Tool | Koleoso | Nigerian ...

    African Journals Online (AJOL)

    ... the use of composite resin restorations as a treatment option in several situations where conventional aesthetic restorations such as porcelain veneers, crowns and cream-metal crown could otherwise be placed. Methods and Materials: Patients who presented with restoration aesthetic challenges over a six months period ...

  9. Bond strength of resin composite to differently conditioned amalgam

    NARCIS (Netherlands)

    Ozcan, M; Vallittu, PK; Huysmans, MC; Kalk, W; Vahlberg, T

    Bulk fracture of teeth, where a part of the amalgam restoration and/or the cusp is fractured, is a common clinical problem. The aim of this study was to evaluate the effect of different surface conditioning methods on the shear bond strength of a hybrid resin composite to fresh amalgam. Amalgams (N

  10. Repair of Defective Composite Resin Restoration: Current Trend ...

    African Journals Online (AJOL)

    Background: Repair of defective composite resins restorations is being increasingly recognized as a viable alternative to replacement. there is however no consensus yet on the treatment protocol. Objective: To determine the views and practice of specialists in Conservative Dentistry in Nigeria as regard to repair procedure ...

  11. Fracture strength of cusp replacing resin composite restorations.

    NARCIS (Netherlands)

    Kuys, R.H.; Fennis, W.M.M.; Kreulen, C.M.; Roeters, F.J.M.; Burgersdijk, R.C.W.

    2003-01-01

    PURPOSE: To assess the influence of an additional shoulder preparation on the fracture strength of a cusp-replacing direct resin composite restoration in a premolar that previously had an amalgam MOD restoration followed by fracture of a cusp. MATERIALS AND METHODS: Two preparation designs were

  12. Resin transfer molding for advanced composite primary aircraft structures

    Science.gov (United States)

    Markus, Alan; Palmer, Ray

    1991-01-01

    Resin Transfer Molding (RTM) has been identified by Douglas Aircraft Company (DAC) and industry to be one of the promising processes being developed today which can break the cost barrier of implementing composite primary structures into a commercial aircraft production environment. The RTM process developments and scale-up plans Douglas Aircrart will be conducting under the NASA ACT contract are discussed.

  13. Chemical composition and palaeobotanical origin of Miocene resins ...

    Indian Academy of Sciences (India)

    The terpenoid composition of resins from the Miocene lignite horizons from the Kerala –Konkan Coast,western India was analyzed by Curie-point pyrolysis –gas chromatography –mass spectrometry (Cupy –GC –MS).The major pyrolysates were cadalene-based bicyclic sesquiterpenoids including some C30-C31 ...

  14. Chemical composition and palaeobotanical origin of Miocene resins ...

    Indian Academy of Sciences (India)

    The terpenoid composition of resins from the Miocene lignite horizons from the Kerala –Konkan Coast,western India was analyzed by Curie-point pyrolysis –gas ... These sesquiterpenoids which are commonly detected in many SE Asian crude oils may be utilised as useful biomarkers for petroleum exploration in the ...

  15. Resistance to bond degradation between dual-cure resin cements and pre-treated sintered CAD-CAM dental ceramics.

    Science.gov (United States)

    Osorio, Raquel; Castillo-de Oyagüe, Raquel; Monticelli, Francesca; Osorio, Estrella; Toledano, Manuel

    2012-07-01

    To evaluate the bond stability of resin cements when luted to glass-reinforced alumina and zirconia CAD/CAM dental ceramics. Eighteen glass-infiltrated alumina and eighteen densely sintered zirconia blocks were randomly conditioned as follows: Group 1: No treatment; Group 2: Sandblasting (125 µm Al₂O₃-particles); and Group 3: Silica-coating (50 µm silica-modified Al₂O₃-particles). Composite samples were randomly bonded to the pretreated ceramic surfaces using different resin cements: Subgroup 1: Clearfil Esthetic Cement (CEC); Subgroup 2: RelyX Unicem (RXU); and Subgroup 3: Calibra (CAL). After 24 h, bonded specimens were cut into 1 ± 0.1 mm² sticks. One-half of the beams were tested for microtensile bond strength (MTBS). The remaining one-half was immersed in 10 % NaOCl aqueous solution (NaOClaq) for 5 h before testing. The fracture pattern and morphology of the debonded surfaces were assessed with a field emission gun scanning electron microscope (FEG-SEM). A multiple ANOVA was conducted to analyze the contributions of ceramic composition, surface treatment, resin cement type, and chemical challenging to MTBS. The Tukey test was run for multiple comparisons (p Resin-ceramic interfacial longevity depended on cement selection rather than on surface pre-treatments. The MDP-containing and the self-adhesive resin cements were both suitable for luting CAD/CAM ceramics. Despite both cements being prone to degradation, RXU luted to zirconia or untreated or sandblasted alumina showed the most stable interfaces. CAL experimented spontaneous debonding in all tested groups.

  16. New acrylic resin composite with improved thermal diffusivity.

    Science.gov (United States)

    Messersmith, P B; Obrez, A; Lindberg, S

    1998-03-01

    Studies have shown that physical characteristics of denture base materials may affect patient acceptance of denture prostheses by altering sensory experience of food during mastication. Thermal diffusivity is one material property that has been cited as being important in determining gustatory response, with denture base acrylic resins having low thermal diffusivity compared with denture base metal alloys. This study prepared and characterized experimental acrylic resin composite material with increased thermal diffusivity. Sapphire (Al2O3) whiskers were added to conventional denture base acrylic resin during processing to achieve loadings of 9.35% and 15% by volume. Cylindrical test specimens containing an embedded thermocouple were used to determine thermal diffusivity over a physiologic temperature range (0 degree to 70 degrees C). Thermal diffusivities of the sapphire containing composites were found to be significantly higher than the unmodified acrylic resin. Thermal diffusivity was found to increase in proportion to the volume percentage of sapphire filler, which suggested that the high aspect ratio ceramic particles formed a pathway for heat conduction through the insulating polymer matrix. The thermal diffusivity of denture base acrylic resin was increased by the addition of thermally conducting sapphire whiskers.

  17. Creep deformation of restorative resin-composites intended for bulk-fill placement.

    Science.gov (United States)

    El-Safty, S; Silikas, N; Watts, D C

    2012-08-01

    To determine the creep deformation of several "bulk-fill" resin-composite formulations in comparison with some other types. Six resin-composites; four bulk-fill and two conventional were investigated. Stainless steel split molds (4 mm × 6 mm) were used to prepare cylindrical specimens for creep testing. Specimens were thoroughly irradiated with 650 mW cm(-2). A total of 10 specimens for each material were divided into two groups (n = 5) according to the storage condition; Group A stored dry at 37 °C for 24h and Group B stored in distilled water at 37 °C in an incubator for 24h. Each specimen was loaded (20 MPa) for 2h and unloaded for 2h. The strain deformation was recorded continuously for 4h. Statistical analysis was performed using a two-way ANOVA followed by one-way ANOVA and the Bonferroni post hoc test at a significance level of a = 0.05. The maximum creep strain % ranged from 0.72% up to 1.55% for Group A and the range for Group B increased from 0.79% up to 1.80% due to water sorption. Also, the permanent set ranged from 0.14% up to 0.47% for Group A and from 0.20% up to 0.59% for Group B. Dependent on the material and storage condition, the percentage of creep strain recovery ranged between 64% and 81%. Increased filler loading in the bulk-fill materials decreased the creep strain magnitude. Creep deformation of all studied resin-composites increased with wet storage. The "bulk-fill" composites exhibited an acceptable creep deformation and within the range exhibited by other resin-composites. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  18. Comparative study to evaluate shear bond strength of RMGIC to composite resin using different adhesive systems

    Science.gov (United States)

    Chandak, Manoj G.; Pattanaik, Navdheeraj; Das, Ayan

    2012-01-01

    Aim: The aim of the study is to compare and evaluate the role of new dental adhesives to bond composite to the resinmodified glass inomer cement (RMGIC). Materials and Methods: Thirty specimens were prepared on acrylic blocks, with wells prepared in it by drilling holes, to retain the RMGIC. The specimens were randomly divided into three groups of ten specimens each. In Group a thin layer of selfetch adhesive (3M ESPE) was applied between the RMGIC and the composite resin FILTEK P60 (3M SPE). In Group II, total etch adhesive (Adeper Scotch bond 2, 3M ESPE) was applied, and in Group III, there was no application of any adhesive between RMGIC and the composite resin. After curing all the specimens, the shear bond strength was measured using an Instron universal testing machine. Results: The results were drawn and tabulated using ANOVA-fishers and Dunnet D statistical tests.The maximum shear bond strength values were recorded in Group I specimens with self-etch adhesive showing a mean value of 2.74 when compared to the Group II adhesive (Total etch) showing a mean shear strength of value 1.89, where no adhesive was used, showed a minimum mean shear bond strength of 1.42. There was a great and significant difference between Group I and Group II (P value 0.05) whereas, both Group I and Group II showed a vast and significant difference from Group III (P value = 0–001). Conclusion: Hence, this present study concludes that application of self-etch adhesive (3M ESPE, U.S.A) in between RMGIC and composite resin increases the shear bond strength between RMGIC and the resin composites, as compared to the total-etch type adhesive (Adeper Scotch bond 2,3M ESPE, U.S.A) as well as without application of the adhesive agent. PMID:23293476

  19. Influence of light curing and sample thickness on microhardness of a composite resin

    Directory of Open Access Journals (Sweden)

    Flávio HB Aguiar

    2009-05-01

    Full Text Available Flávio HB Aguiar1, Kelly RM Andrade1, Débora AN Leite Lima1, Gláucia MB Ambrosano2, José R Lovadino11Department of Restorative Dentistry; 2Department of Social Dentistry/Statistics, Piracicaba Dental School, State University of Campinas, SP, BrazilAbstract: The aim of this in vitro study was to evaluate the influence of light-curing units and different sample thicknesses on the microhardness of a composite resin. Composite resin specimens were randomly prepared and assigned to nine experimental groups (n = 5: considering three light-curing units (conventional quartz tungsten halogen [QTH]: 550 mW/cm2 – 20 s; high irradiance QTH: 1160 mW/cm2 – 10 s; and light-emitting diode [LED]: 360 mW/cm2 – 40 s and three sample thicknesses (0.5 mm, 1 mm, and 2 mm. All samples were polymerized with the light tip 8 mm away from the specimen. Knoop microhardness was then measured on the top and bottom surfaces of each sample. The top surfaces, with some exceptions, were almost similar; however, in relation to the bottom surfaces, statistical differences were found between curing units and thicknesses. In all experimental groups, the 0.5-mm-thick increments showed microhardness values statistically higher than those observed for 1- and -2-mm increments. The conventional and LED units showed higher hardness mean values and were statistically different from the high irradiance unit. In all experimental groups, microhardness mean values obtained for the top surface were higher than those observed for the bottom surface. In conclusion, higher levels of irradiance or thinner increments would help improve hybrid composite resin polymerization.Keywords: photo-polymerization, light-curing distance, light-curing units, composite resin, composite thickness, microhardness

  20. Comparative study to evaluate shear bond strength of RMGIC to composite resin using different adhesive systems

    Directory of Open Access Journals (Sweden)

    Manoj G Chandak

    2012-01-01

    Full Text Available Aim: The aim of the study is to compare and evaluate the role of new dental adhesives to bond composite to the resinmodified glass inomer cement (RMGIC. Materials and Methods: Thirty specimens were prepared on acrylic blocks, with wells prepared in it by drilling holes, to retain the RMGIC. The specimens were randomly divided into three groups of ten specimens each. In Group a thin layer of selfetch adhesive (3M ESPE was applied between the RMGIC and the composite resin FILTEK P60 (3M SPE. In Group II, total etch adhesive (Adeper Scotch bond 2, 3M ESPE was applied, and in Group III, there was no application of any adhesive between RMGIC and the composite resin. After curing all the specimens, the shear bond strength was measured using an Instron universal testing machine. Results: The results were drawn and tabulated using ANOVA-fishers and Dunnet D statistical tests.The maximum shear bond strength values were recorded in Group I specimens with self-etch adhesive showing a mean value of 2.74 when compared to the Group II adhesive (Total etch showing a mean shear strength of value 1.89, where no adhesive was used, showed a minimum mean shear bond strength of 1.42. There was a great and significant difference between Group I and Group II (P value 0.05 whereas, both Group I and Group II showed a vast and significant difference from Group III (P value = 0-001. Conclusion: Hence, this present study concludes that application of self-etch adhesive (3M ESPE, U.S.A in between RMGIC and composite resin increases the shear bond strength between RMGIC and the resin composites, as compared to the total-etch type adhesive (Adeper Scotch bond 2,3M ESPE, U.S.A as well as without application of the adhesive agent.

  1. Ten-year clinical assessment of three posterior resin composites and two amalgams.

    Science.gov (United States)

    Mair, L H

    1998-08-01

    The long-term clinical performance of three posterior resin composites and two amalgams was assessed. Thirty Class II restorations each of P-30, Occlusin, Clearfil Posterior (composites), New True Dentalloy, and Solila Nova (amalgams) were placed. Reviews took place at 6 months and at 1, 2, 3, 4, 5, and 10 years. At each visit the gingival condition, the contact point status, and the presence of ledges, gaps, or recurrent caries were assessed. The color match, cavosurface marginal stain, general surface stain, tarnish, and corrosion were also scored where applicable. Epoxy resin replicas were used to measure the maximum depth of wear. After 10 years, there had been corrosion of both the high- and low-copper amalgams and a slight deterioration in color match of a number of composite restorations. Eighteen (of 20) Occlusin restorations had obvious cavosurface marginal stain, attributed to staining of the unfilled bonding resin layer. Statistical analysis indicated that New True Dentalloy, Solila Nova, and Clearfil-P exhibited significantly less wear than Occlusin and P-30. None of the restorations examined at the 10-year recall required replacement. The five materials, placed in a dental school environment, provided adequate clinical service for 10 years.

  2. Ceramic matrix and resin matrix composites - A comparison

    Science.gov (United States)

    Hurwitz, Frances I.

    1987-01-01

    The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.

  3. Ceramic matrix and resin matrix composites: A comparison

    Science.gov (United States)

    Hurwitz, Frances I.

    1987-01-01

    The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.

  4. Process Optimization of Bismaleimide (BMI) Resin Infused Carbon Fiber Composite

    Science.gov (United States)

    Ehrlich, Joshua W.; Tate, LaNetra C.; Cox, Sarah B.; Taylor, Brian J.; Wright, M. Clara; Faughnan, Patrick D.; Batterson, Lawrence M.; Caraccio, Anne J.; Sampson, Jeffery W.

    2013-01-01

    Engineers today are presented with the opportunity to design and build the next generation of space vehicles out of the lightest, strongest, and most durable materials available. Composites offer excellent structural characteristics and outstanding reliability in many forms that will be utilized in future aerospace applications including the Commercial Crew and Cargo Program and the Orion space capsule. NASA's Composites for Exploration (CoEx) project researches the various methods of manufacturing composite materials of different fiber characteristics while using proven infusion methods of different resin compositions. Development and testing on these different material combinations will provide engineers the opportunity to produce optimal material compounds for multidisciplinary applications. Through the CoEx project, engineers pursue the opportunity to research and develop repair patch procedures for damaged spacecraft. Working in conjunction with Raptor Resins Inc., NASA engineers are utilizing high flow liquid infusion molding practices to manufacture high-temperature composite parts comprised of intermediate modulus 7 (IM7) carbon fiber material. IM7 is a continuous, high-tensile strength composite with outstanding structural qualities such as high shear strength, tensile strength and modulus as well as excellent corrosion, creep, and fatigue resistance. IM7 carbon fiber, combined with existing thermoset and thermoplastic resin systems, can provide improvements in material strength reinforcement and deformation-resistant properties for high-temperature applications. Void analysis of the different layups of the IM7 material discovered the largest total void composition within the [ +45 , 90 , 90 , -45 ] composite panel. Tensile and compressional testing proved the highest mechanical strength was found in the [0 4] layup. This paper further investigates the infusion procedure of a low-cost/high-performance BMI resin into an IM7 carbon fiber material and the

  5. Fissure sealant materials: Wear resistance of flowable composite resins.

    Science.gov (United States)

    Asefi, Sohrab; Eskandarion, Solmaz; Hamidiaval, Shadi

    2016-01-01

    Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow), Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists). A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm(2) and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm(2)of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics.

  6. Fissure sealant materials: Wear resistance of flowable composite resins

    Directory of Open Access Journals (Sweden)

    Sohrab Asefi

    2016-08-01

    Full Text Available Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow, Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists. A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm2 and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm2of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics.

  7. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic.

    Science.gov (United States)

    Moradabadi, Ashkan; Roudsari, Sareh Esmaeily Sabet; Yekta, Bijan Eftekhari; Rahbar, Nima

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30× magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. © 2013.

  8. Characterization of selected LDEF polymer matrix resin composite materials

    Science.gov (United States)

    Young, Philip R.; Slemp, Wayne S.; Witte, William G., Jr.; Shen, James Y.

    1991-01-01

    The characterization of selected graphite fiber reinforced epoxy (934 and 5208) and polysulfone (P1700) matrix resin composite materials which received 5 years and 10 months of exposure to the LEO environment on the Long Duration Exposure Facility is reported. Resin loss and a decrease in mechanical performance as well as dramatic visual effects were observed. However, chemical characterization including infrared, thermal, and selected solution property measurements showed that the molecular structure of the polymeric matrix had not changed significantly in response to this exposure. The potential effect of a silicon-containing molecular contamination of these specimens is addressed.

  9. ADHESIVE SYSTEM AFFECTS REPAIR BOND STRENGTH OF RESIN COMPOSITE

    Directory of Open Access Journals (Sweden)

    Özgür IRMAK

    2017-10-01

    Full Text Available Purpose: This study evaluated the effects of different adhesive systems on repair bond strength of aged resin composites. Materials and Methods: Ninety composite discs were built and half of them were subjected to thermal aging. Aged and non-aged specimens were repaired with resin composite using three different adhesive systems; a two-step self-etch adhesive, a two-step total-etch adhesive and a one-step self-etch adhesive; then they were subjected to shear forces. Data were analyzed statistically. Results: Adhesive type and aging significantly affected the repair bond strengths (p<0.0001. No statistical difference was found in aged composite groups repaired with two-step self- etch or two-step total-etch adhesive. One-step self-etch adhesive showed lower bond strength values in aged composite repair (p<0.0001. Conclusion: In the repair of aged resin composite, two-step self-etch and two-step total-etch adhesives exhibited higher shear bond strength values than that of one-step self-etch adhesive.

  10. Dental composites and amalgam and physical development in children.

    Science.gov (United States)

    Maserejian, N N; Hauser, R; Tavares, M; Trachtenberg, F L; Shrader, P; McKinlay, S

    2012-11-01

    Resin-based composite dental restoration materials may release bisphenol-A, an endocrine-disrupting chemical. Using secondary analysis of a randomized clinical safety trial of amalgam vs. composites, we tested the hypothesis that dental restoration materials affect children's growth. Children (N = 218 boys, N = 256 girls) aged 6 to 10 yrs at baseline with ≥ 2 decayed posterior teeth were randomized to amalgam or composites (bisphenol-A-diglycidyl-dimethacrylate composite for permanent teeth, urethane-dimethacrylate compomer for primary teeth) for treatment of posterior caries throughout follow-up. Primary outcomes for this analysis were 5-year changes in BMI-for-age z-scores, body fat percentage (BF%), and height velocity; exploratory analyses (n = 113) examined age at menarche. Results showed no significant differences between treatment assignment and changes in physical development in boys [(composites vs. amalgam) BF%, 4.9 vs. 5.7, p = 0.49; (BMI-z-score) 0.13 vs. 0.25, p = 0.36] or girls (8.8 vs. 7.7, p = 0.95; 0.36 vs. 0.21, p = 0.49). Children with more treatment on primary teeth had greater increases in BF% regardless of material type. Girls assigned to composites had lower risk of menarche during follow-up (hazard ratio = 0.57, 95% CI 0.35-0.95). Overall, there were no significant differences in physical development over 5 years in children treated with composites or amalgam. Additional studies examining these restoration materials in relation to age at menarche are warranted (clinicaltrials.gov number NCT00065988).

  11. Microwave absorption properties of graphite flakes-phenolic resin composite

    Science.gov (United States)

    Gogoi, Jyoti P.; Gogoi, Pragyan J.; Bhattacharyya, Nidhi S.

    2013-01-01

    In the present investigation, microwave absorption properties of a conductor back single layer designed on graphite flakes (GF)-novolac phenolic resin (NPR) composites is studied. The complex permittivity of the developed composite enhance for higher GF percentages. The reflection loss(RL) measured using E8362C VNA shows a maximum RL values -25 dB at 9.8 GHz for 7 wt. % composition with -10 dB bandwidth of 0.3 GHz. The developed composites are being light weight and cost effective shows potential to be used as dielectric absorber.

  12. Correlations of norbornenyl crosslinked polyimide resin structures with resin thermo-oxidative stability, resin glass transition temperature and composite initial mechanical properties

    Science.gov (United States)

    Alston, William B.

    1988-01-01

    PMR (polymerization of monomeric reactants) methodology was used to prepare 70 different polyimide oligomeric resins and 30 different unidirectional graphite fiber/polyimide composites. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on resin thermo-oxidative stability and glass transition temperature (Tg) of the cured/postcured resins. A linear correlation of decreasing 316 C resin weight loss/surface area versus (1) decreasing aliphatic content, or (2) increasing benzylic/aliphatic content stoichiometry ratio over a wide range of resin compositions was observed. An almost linear correlation of Tg versus molecular distance between the crosslinks was also observed. An attempt was made to correlate Tg with initial composite mechanical properties (flexural strength and interlaminar shear strength). However, the scatter in mechanical strength data prevented obtaining a clear correlation. Instead, only a range of composite mechanical properties was obtained at 25, 288, and 316 C. Perhaps more importantly, what did become apparent during the correlation study was (1) the PMR methodology could be used to prepare composites from resins containing a wide variety of monomer modifications, (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins formulated exhibited satisfactory processing flow, and (3) that PMR resins exhibited predictable rates of 316 C weight loss/surface area based on their benzylic/aliphatic stoichiometery ratio.

  13. Toxicity test of a dental commercial composite

    OpenAIRE

    Ponce-Bravo, Santa; Ledesma-Montes, Constantino; Mart?nez-Rivera, Jos?-Luis; Garc?s-Ort?z, Maricela

    2015-01-01

    Background International rules must be followed for testing biosecurity in dental materials. A new brand of restorative material appeared in the market and regulations indicated that it should be tested for toxicity. Objectives The aim of this study was to determine the 90-day sub chronic toxicity of one triethylene glycol dimethacrylate containing composite (MEDENTAL Light-Cure Composite?) orally administered to rats according to Organization for Economic Co-Operation and Development no. 48 ...

  14. Resin composite repair for implant-supported crowns.

    Science.gov (United States)

    Bonfante, Estevam A; Suzuki, Marcelo; Hirata, Ronaldo; Bonfante, Gerson; Fardin, Vinicius P; Coelho, Paulo G

    2017-08-01

    This study evaluated the reliability of implant-supported crowns repaired with resin composites. Fifty-four titanium abutments were divided in three groups (n = 18 each) to support resin nanoceramic molar crowns, as follows: (LU) (Lava Ultimate, 3M ESPE); LU repaired with either a direct or an indirect resin composite. Samples were subjected to mouth-motion accelerated-life testing in water (n = 18). Cumulative damage with a use stress of 300 N was used to plot Weibull curves for group comparison. Reliability was calculated for a mission of 100,000 cycles at 400 N load. Beta values were 0.83 for LU, 0.31 and 0.27 for LU repaired with Filtek and Ceramage, respectively. Weibull modulus for LU was 9.5 and η = 1047 N, m = 6.85, and η = 1002 N for LU repaired with Ceramage, and m = 4.65 and η = 766 N for LU repaired with Filtek (p material, and detailed fractography is presented. The performance of resin nanoceramic material repaired with an indirect composite was maintained after accelerated-life testing compared to unrepaired controls. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1481-1489, 2017. © 2016 Wiley Periodicals, Inc.

  15. Ten-year Clinical Performance of Posterior Resin Composite Restorations.

    Science.gov (United States)

    Krämer, Norbert; Reinelt, Christian; Frankenberger, Roland

    2015-08-01

    To investigate the clinical behavior of two different resin-based restorative systems in Class II cavities in a controlled prospective split-mouth study over 10 years. Thirty patients received 68 resin composite restorations (Solobond M + Grandio: n = 36; Syntac + Tetric Ceram: n = 32) by one dentist in a private practice. 35% of cavities revealed no enamel at the bottom of the proximal box, 48% of cavities provided Grandio restoration suffered marginal fracture with exposed dentin and one Tetric Ceram restoration failed due to cusp fracture. After 10 years, Grandio showed higher surface roughness (p = 0.03) and less color match (p = 0.024; Mann-Whitney U-test). Molar restorations performed worse than premolar fillings regarding marginal integrity (4 and 10 years), filling integrity (4, 8, and 10 years), and tooth integrity (4, 8, and 10 years). The main reasons for degradation of resin composites were chipping and cracks in molar restorations after 8 years. Beyond the 4-year recall, marginal staining increased (43% bravo for stained margins at four years, 52% at 8 years, and 71% at 10 years). Tooth integrity deteriorated significantly due to more enamel cracks and chipping over time (9% at baseline and 89% after 10 years (p<0.05). Direct resin composite restorations performed satisfactorily over 10 years of clinical service.

  16. Development of a novel resin-based dental material with dual biocidal modes and sustained release of Ag+ ions based on photocurable core-shell AgBr/cationic polymer nanocomposites.

    Science.gov (United States)

    Cao, Weiwei; Zhang, Yu; Wang, Xi; Chen, Yinyan; Li, Qiang; Xing, Xiaodong; Xiao, Yuhong; Peng, Xuefeng; Ye, Zhiwen

    2017-07-01

    Research on the incorporation of cutting-edge nano-antibacterial agent for designing dental materials with potent and long-lasting antibacterial property is demanding and provoking work. In this study, a novel resin-based dental material containing photocurable core-shell AgBr/cationic polymer nanocomposite (AgBr/BHPVP) was designed and developed. The shell of polymerizable cationic polymer not only provided non-releasing antibacterial capability for dental resins, but also had the potential to polymerize with other methacrylate monomers and prevented nanoparticles from aggregating in the resin matrix. As a result, incorporation of AgBr/BHPVP nanocomposites did not adversely affect the flexural strength and modulus but greatly increased the Vicker's hardness of resin disks. By continuing to release Ag + ions without the impact of anaerobic environment, resins containing AgBr/BHPVP nanoparticles are particularly suitable to combat anaerobic cariogenic bacteria. By reason of the combined bactericidal effect of the contact-killing cationic polymers and the releasing-killing Ag + ions, AgBr/BHPVP-containing resin disks had potent bactericidal activity against S. mutans. The long-lasting antibacterial activity was also achieved through the sustained release of Ag + ions due to the core-shell structure of the nanocomposites. The results of macrophage cytotoxicity showed that the cell viability of dental resins loading less than 1.0 wt% AgBr/BHPVP was close to that of neat resins. The AgBr/BHPVP-containing dental resin with dual bactericidal capability and long term antimicrobial effect is a promising material aimed at preventing second caries and prolonging the longevity of resin composite restorations.

  17. Comparative analysis of the shrinkage stress of composite resins

    Directory of Open Access Journals (Sweden)

    Rosana Aparecida Pereira

    2008-02-01

    Full Text Available The aim of this study was to compare the shrinkage stress of composite resins by three methods. In the first method, composites were inserted between two stainless steel plates. One of the plates was connected to a 20 kgf load cell of a universal testing machine (EMIC-DL-500. In the second method, disk-shaped cavities were prepared in 2-mm-thick Teflon molds and filled with the different composites. Gaps between the composites and molds formed after polymerization were evaluated microscopically. In the third method, the wall-to-wall shrinkage stress of the resins that were placed in bovine dentin cavities was evaluated. The gaps were measured microscopically. Data were analyzed by one-way ANOVA and Tukey's test (alpha=0.05. The obtained contraction forces were: Grandio = 12.18 ± 0.428N; Filtek Z 250 = 11.80 ± 0.760N; Filtek Supreme = 11.80 ± 0.707 N; and Admira = 11.89 ± 0.647 N. The gaps obtained between composites and Teflon molds were: Filtek Z 250 = 0.51 ± 0.0357%; Filtek Supreme = 0.36 ± 0.0438%; Admira = 0.25 ± 0.0346% and Grandio = 0.16 ± 0.008%. The gaps obtained in wall-to-wall contraction were: Filtek Z 250 = 11.33 ± 2.160 µm; Filtek Supreme = 10.66 ± 1.211µm; Admira = 11.16 ± 2.041 µm and Grandio = 10.50 ± 1.224 µm. There were no significant differences among the composite resins obtained with the first (shrinkage stress generated during polymerization and third method (wall-to-wall shrinkage. The composite resins obtained with the second method (Teflon method differed significantly regarding gap formation.

  18. Comparative analysis of the shrinkage stress of composite resins.

    Science.gov (United States)

    Pereira, Rosana Aparecida; Araujo, Paulo Amarante de; Castañeda-Espinosa, Juan Carlos; Mondelli, Rafael Francisco Lia

    2008-01-01

    The aim of this study was to compare the shrinkage stress of composite resins by three methods. In the first method, composites were inserted between two stainless steel plates. One of the plates was connected to a 20 kgf load cell of a universal testing machine (EMIC-DL-500). In the second method, disk-shaped cavities were prepared in 2-mm-thick Teflon molds and filled with the different composites. Gaps between the composites and molds formed after polymerization were evaluated microscopically. In the third method, the wall-to-wall shrinkage stress of the resins that were placed in bovine dentin cavities was evaluated. The gaps were measured microscopically. Data were analyzed by one-way ANOVA and Tukey's test (alpha=0.05). The obtained contraction forces were: Grandio = 12.18 +/- 0.428N; Filtek Z 250 = 11.80 +/- 0.760N; Filtek Supreme = 11.80 +/- 0.707 N; and Admira = 11.89 +/- 0.647 N. The gaps obtained between composites and Teflon molds were: Filtek Z 250 = 0.51 +/- 0.0357%; Filtek Supreme = 0.36 +/- 0.0438%; Admira = 0.25 +/- 0.0346% and Grandio = 0.16 +/- 0.008%. The gaps obtained in wall-to-wall contraction were: Filtek Z 250 = 11.33 +/- 2.160 microm; Filtek Supreme = 10.66 +/- 1.211 microm; Admira = 11.16 +/- 2.041 microm and Grandio = 10.50 +/- 1.224 microm. There were no significant differences among the composite resins obtained with the first (shrinkage stress generated during polymerization) and third method (wall-to-wall shrinkage). The composite resins obtained with the second method (Teflon method) differed significantly regarding gap formation.

  19. Differences in color, translucency and fluorescence between flowable and universal resin composites.

    Science.gov (United States)

    Yu, Bin; Lee, Yong-Keun

    2008-10-01

    To evaluate the optical properties such as color, translucency and fluorescence of flowable resin composites, and compare them with the corresponding shade universal resin composites of the same brand. Four brands of flowable and universal resin composites of the same shade designation (A2) were investigated. Color of specimens (2mm in thickness) was measured after polymerization on a reflection spectrophotometer over background of white, black and each corresponding composite material itself. Color differences (DeltaE(ab)(*)) between each combination of resin composites were determined. Translucency parameter (TP) and color difference by the fluorescent emission (DeltaE(ab)(*)-FL) of materials were also calculated. Differences in the optical properties of flowable and universal resin composites were analyzed with one-way ANOVA. DeltaE(ab)(*) between the flowable and the corresponding universal resin composites was in the range of 1.0-6.0 DeltaE(ab)(*) units, which was perceptible (DeltaE(ab)(*)>2.6) in three brands. Flowable resin composites revealed lower TP values in two of the four brands. DeltaE(ab)(*) between flowable and the corresponding universal resin composites was influenced by their difference in translucency. All the four universal resin composites and two flowable resin composites showed fluorescent peak, and the range of DeltaE(ab)(*)-FL was 0.3-2.3 DeltaE(ab)(*) units. Optical properties of flowable and universal resin composites was significantly different (presin composites should be considered for clinically acceptable color matching.

  20. Development of new addition-type composite resins

    Science.gov (United States)

    Kray, R. J.

    1981-01-01

    The most promising of a number of new addition type polyimides and polyaromatic melamine (NCNS) resins for use in high performance composite materials. Three different cure temperature ranges were of interest: 530-560 K (500-550 F), 475-530 K (400-500 F), and 450 K (350 F). Examined were a wide variety of polyimide precursors terminated with 5 norbornene groups and addition polymerized at 560 K similar to PMR-15 and LARC-160 polyimides. In addition, a number of lower curing cinnamal end capped polyimides and a bismaleimide were investigated but were not found promising. A group of NCNS resins were investigated and some were found to be superior to current epoxy resins in moisture resistance, oxidative aging and flame and smoke properties.

  1. Translucency and masking ability of various composite resins at different thicknesses.

    Science.gov (United States)

    Darabi, Farideh; Radafshar, Golpar; Tavangar, Maryam; Davaloo, Reza; Khosravian, Aref; Mirfarhadi, Nastaran

    2014-09-01

    Optical properties of the composite resins, concerning their translucency and thickness, are affected by discolored tooth structure or inherent darkness of the oral cavity. This study aimed to compare the translucency parameter (TP) of five different composite resins in different thicknesses and to evaluate their masking ability in black backgrounds. Five brands of composite resins; Gradia (GC) and Crystalline (Confi-dental) in opaque A2 (OA2), Vit-l-escence (Ultradent) in opaque snow (OS), Herculite XRV (Kerr) and Opallis (FGM) in dentin A2 (DA2) shades were selected to enroll the study. Color coordinates of each composite were determined at 0.5, 1, and 1.5 mm thicknesses on a white backing, the backing of material itself and a black backing were calculated by using a spectrophotometer to evaluate the translucency parameter (TP) of the study materials. The masking ability was also calculated from the specimens on the material itself and on black backing. The values under 2 were estimated as imperceptible. One-way ANOVA, T-test and Tukey HSD were employed for statistical analysis. The masking ability values, recorded for the 1.5 mm-thick specimens, were in the range of imperceptible except for the Herculite. There was no difference in TP values of the materials at 1.5 mm thickness. Opaque snow shade of Vit-l-escence and opaque A2 shade of Gradia showed lower TP values in comparison with the other 1 and 0.5 mm-thick materials and this difference was statistically significant (pcomposite resins could not mask the black background color.

  2. Repair of amalgam restorations with composite resin and bonded amalgam: a microleakage study.

    Science.gov (United States)

    Popoff, Daniela Araújo Veloso; Gonçalves, Fabiana Santos; Magalhães, Cláudia Silami; Moreira, Allyson Nogueira; Ferreira, Raquel Conceição; Mjör, Ivar A

    2011-01-01

    Total replacement is the most common technique for defective amalgam restorations, and it represents a major part of restorative dental treatment. Repair is an alternative option for amalgam restorations with localized defects. This study compared microleakage of amalgam restorations repaired by bonded amalgam or composite resin. Thirty extracted human pre-molars were prepared and restored with class I amalgam. A simulated defect was prepared that included the cavosurface margin on restorations, and the pre-molars were assigned to two treatment groups (n=15): In group 1, premolars were treated by composite resin (34% Tooth Conditioner Gel + Adper Single Bond 2 + Z100) and in group 2, premolars were repaired by bonded amalgam (34% Tooth Conditioner Gel + Prime and Bond 2.1 + Permite C). The teeth were immersed in a 50% silver nitrate solution, thermocycled, sectioned longitudinally and then observed by three examiners using a stereomicroscope. Microleakage was evaluated using a 0-4 scale for dye penetration, and data was analyzed by Kruskal Wallis and Dunn tests. Neither of the two methods eliminated microleakage completely. Composite resin was significantly the most effective for repair/tooth interface sealing (score 0 = 80.0%; P=0.0317). For the repair/restoration interface, composite resin was also statistically more effective as a sealant (score 0=66%; P=0.0005) when compared to the bonded amalgam technique (score 0=13%; P=0.0005). The use of adhesive systems significantly affected the ability to seal the repair/ tooth interface. However, at the level of the repair/restoration interface, the bonded amalgam technique may increase microleakage.

  3. Shear bond strength of the amalgam-resin composite interface.

    Science.gov (United States)

    Machado, Camilo; Sanchez, Eliana; Alapati, Satish; Seghi, Robert; Johnston, William

    2007-01-01

    This study compared the initial and one year shear bond strengths (SBS) of resin composite bonded to amalgam using Amalgambond-Plus. Resin composite cylinders (Point 4, Kerr Corporation) were bonded to either etched-enamel (A), 50% etched enamel-50% polished amalgam (B), airborne-particle abraded amalgam (C), carbide bur prepared amalgam (D) and airborne-particle abraded 50% amalgam-50% etched-enamel (E). Shear bond strengths were determined using a standardized testing device (Ultradent Products) in a universal testing machine (Instron model 4204). The failed interfaces were evaluated with SEM to obtain visual evidence of the failure mode. ANOVA indicated significant differences among the groups (p composite masking has the strongest, most durable SBS on airborne-particle abraded amalgam and airborne-particle abraded enamel-amalgam surfaces and could be used as a method to improve the esthetics of amalgam restorations.

  4. Effects of abrasive and fiber components in medium on wear of composite resins.

    Science.gov (United States)

    Kakuta, Kiyoshi; Ogura, Hideo

    2008-09-01

    Effects of abrasive and fiber components in a medium on the wear behavior of composite resins were evaluated. Calcium diphosphate and methyl cellulose were included in the medium as abrasive and fiber components respectively. A range of 0, 4, or 8% abrasive- or fiber-containing media were applied on a composite resin specimen during a simulated occlusal wear test. Four composite resins, Clearfil AP-X, Z100 Restorative, SOLARE P, and SOLIDEX F, were tested to evaluate the effects of these components in the medium. Presence of abrasive material in the medium increased the wear of composite resins significantly, but its effect differed among the composite resins. Presence of fiber material in the medium significantly decreased the wear of two composite resins, whereas the other two composites showed no significant differences. Nonetheless, presence of fiber in the medium generally tended to prevent the wear of composite resins.

  5. Effect of Sandblasting on Shear Bond Strength Composite Resin Veneer

    Directory of Open Access Journals (Sweden)

    Octarina Octarina

    2013-07-01

    Full Text Available Attachment between restoration and enamel surface in indirect resin composite veneer restoration (IRCV is obtained using multi-step (MS resin cement. Recently, a one step self-adhesive dual-cured resin cement (SADRC was introduced. Objective: To determine the effect of sandblasting on shear bond strength (SBS of IRCV to enamel using MS resin cement and SADRC. Methods: Forty specimens of buccal surface of enamel human were light-cured in Solidilite chamber and were divided into two groups: IRCV without sandblasting (n=20 and with sandblasting for 10 seconds (n=20 and then bonded to enamel using MS (n=10 and SADRC (n=10, respectively. After 24h SBS of specimens were tested using a Universal Testing Machine. Data were analyzed statistically by one-way ANOVA. Results: The average SBS value of IRCV without SB and bonded with MS was 18.95+7.80MPa and MS with SB was 19.30+ SB (4.85+2.12MPa and SADRC with SB (9.57+3.45MPa(p<0.05. Conclusion: increased SBS VIRK to enamel using MS resin cement than SADRC.  

  6. Does the light source affect the repairability of composite resins?

    Science.gov (United States)

    Karaman, Emel; Gönülol, Nihan

    2014-01-01

    The aim of this study was to examine the effect of the light source on the microshear bond strength of different composite resins repaired with the same substrate. Thirty cylindrical specimens of each composite resin--Filtek Silorane, Filtek Z550 (3M ESPE), Gradia Direct Anterior (GC), and Aelite Posterior (BISCO)--were prepared and light-cured with a QTH light curing unit (LCU). The specimens were aged by thermal cycling and divided into three subgroups according to the light source used--QTH, LED, or PAC (n = 10). They were repaired with the same substrate and a Clearfil Repair Kit (Kuraray). The specimens were light-cured and aged for 1 week in distilled water at 37 °C. The microshear bond strength and failure modes were assessed. There was no significant difference in the microshear bond strength values among the composite resins, except for the Filtek Silorane group that showed significantly lower bond strength values when polymerized with the PAC unit compared to the QTH or LED unit. In conclusion, previously placed dimethacrylate-based composites can be repaired with different light sources; however, if the composite to be repaired is silorane-based, then using a QTH or LED device may be the best option.

  7. Comparison of Microleakage of Composite Resin Veneering Systems at the Alloy Interface

    Science.gov (United States)

    1988-09-01

    technique that there is leakage around resin veneers in gold crowns. Microleakage studies have been used primarily for the evaluation of direct...investigation is to evaluate the bond between veneering composite resin and metal substructure. Measurement of microleakage at the composite resin-alloy...34OVERPRINT" COMPARISON OF MICROLEAKAGE OF COMPOSITE RESIN VENEERING SYSTEMS AT THE ALLOY INTERFACE A THESIS Presented to the Faculty of The University

  8. Fracture frequency and longevity of fractured resin composite, polyacid-modified resin composite, and resin-modified glass ionomer cement class IV restorations: an up to 14 years of follow-up

    DEFF Research Database (Denmark)

    van Dijken, Jan W V; Pallesen, Ulla

    2010-01-01

    The aim of this study was to evaluate the fracture frequency and longevity of fractured class IV resin composite (RC), polyacid-modified resin composite (compomer; PMRC), and resin-modified glass ionomer cement (RMGIC) restorations in a longitudinal long-term follow-up. Eighty-five class IV RC (43...

  9. Influence of polymerization time and depth of cure of resin composites determined by Vickers hardness

    Directory of Open Access Journals (Sweden)

    Marco Lombardini

    2012-01-01

    Conclusion: Among the materials tested, the nanofilled and the nanohybrid resin composites were rather insensible to thickness variations. Miicrohybrid composites, instead, had features different from one another.

  10. Study on thermal conductive BN/novolac resin composites

    International Nuclear Information System (INIS)

    Li, Shasha; Qi, Shuhua; Liu, Nailiang; Cao, Peng

    2011-01-01

    Highlights: → Boron nitride (BN) particles were used to modify novolac resin. → BN particles were pretreated by γ-aminopropyltriethoxysilane. → The thermal conductivity trend of composite almost agrees with the predicted data from the Maxwell-Eucken model. → At BN concentration of 80 wt.%, thermal conductivity value of composite is 4.5 times that of pure novolac resin. → Combined use of the larger and smaller particles with a mass ratio of 1:2 provides the composites with the maximum thermal conductivity among the testing systems. → The composite thermal property also increases with an increase in the BN concentration. - Abstract: In this study, γ-aminopropyltriethoxysilane-treated boron nitride (BN) particles were used to modify novolac resin. The effect of varying the BN concentration, particle size, and hybrid BN fillers with the binary particle size distribution on the thermal conductivity of the composites was investigated. Scanning electron microscopy (SEM) imaging showed homogeneously dispersed treated BN particles in the matrix. Furthermore, the thermal conductivity increased as the BN concentration was increased. This behavior was also observed when the filler size was increased. Experimentally obtained thermal conductivity values agree with the predicted data from the Maxwell-Eucken model well at less than 70 wt.% BN loading. A larger particle size BN-filled novolac resin exhibits a higher thermal conductivity than a smaller particle size BN-filled one. The combined use of 0.5 and 15 μm particles with a mass ratio of 2:1 achieved the maximum thermal conductivity among the testing systems. The thermal resistance properties of the composites were also studied.

  11. Advancing Discontinuous Fiber-Reinforced Composites above Critical Length for Replacing Current Dental Composites and Amalgam.

    Science.gov (United States)

    Petersen, Richard C

    2017-02-01

    Clinicians have been aware that posterior dental particulate-filled composites (PFCs) have many placement disadvantages and indeed fail clinically at an average rate faster than amalgam alloys. Secondary caries is most commonly identified as the chief failure mechanism for both dental PFCs and amalgam. In terms of a solution, fiber-reinforced composites (FRCs) above critical length (L c ) can provide mechanical property safety factors with compound molding packing qualities to reduce many problems associated with dental PFCs. Discontinuous chopped fibers above the necessary L c have been incorporated into dental PFCs to make consolidated molding compounds that can be tested for comparisons with PFC controls on mechanical properties, wear resistance, void-defect occurrence and packing ability to reestablish the interproximal contact. Further, imaging characterizations can aid in providing comparisons for FRCs with other materials using scanning electron microscopy, atomic force microscopy and photographs. Also, the amalgam filling material has finally been tested by appropriate ASTM flexural bending methods that eliminate shear failure associated with short span lengths in dental standards for comparison with dental PFCs to best explain increased longevity for the amalgam when compared to dental PFCs. Accurate mechanical tests also provide significant proof for superior advantages with FRCs. Mechanical properties tested included flexural strength, yield strength, modulus, resilience, work of fracture, critical strain energy release and critical stress intensity factor. FRC molding compounds with fibers above L c extensively improve all mechanical properties over PFC dental paste and over the amalgam for all mechanical properties except modulus. The dental PFC also demonstrated superior mechanical properties over the amalgam except modulus to provide a better explanation for increased PFC failure due to secondary caries. With lower PFC modulus, increased adhesive

  12. Effect of organoclay incorporation on dental resin morphology;Efeito da incorporacao de argila oganofilica na morfologia de resina adontologica

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Nadja M.S.; Reis, Romulo P.B. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Programa de Pos-graduacao em Ciencia e Engenharia de Materiais; Leite, Itamara F. [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Programa de Pos-Graduacao em Ciencia de Materiais; Morais, Crislene R.S.; Silva, Suedina M.L., E-mail: suedina@dema.ufcg.edu.b [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2009-07-01

    The objective of the present work was to incorporate nanosilicates in commercial dental resins in order to prepare dental nanocomposites competitive as commercial nanoparticulates dental resins. Thus, a silicate, Cloisite 20A (C20A), was incorporated in a microhybrid dental resin (Z100) and morphological properties of the nanocomposites evaluated as a function of the incorporation method and the amount of filler employed. The samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD results evidence that nanocomposites have been obtained and according to SEM results, the morphology of microhybrid resin was modified when C20A nanoparticulate was incorporated improve the size distribution and reduce the agglomeration of the particles. (author)

  13. Color Stability Assessment of Two Different Composite Resins with Variable Immersion Time Using Various Beverages: An In vitro Study.

    Science.gov (United States)

    Kumar, M Senthil; Ajay, R; Miskeen Sahib, S A; Chittrarasu, M; Navarasu, M; Ragavendran, N; Burhanuddin Mohammed, Omar Farooq

    2017-11-01

    The aim of the study was to evaluate the difference in the color of microhybrid (MH) and nanofilled (NF) composite resins after 24 and 48 h in beverages such as red wine (RW), Coca-Cola, and distilled water. The specific objective of this study was to investigate the cumulative effect of the colorant solutions on the dental composites. MH and NF composite resins (A2 shade) were used in this current study. Sixty disk-shaped material specimens (10 mm in diameter × 2 mm in thickness) were prepared using a fiber mold (ring), with the desired dimensions. The specimen surfaces were polished using super-snap polishing system. Sixty specimens were divided into two groups of 30 each (Group I: MH resin composite; Group II: NF resin composite). Both the groups divided into six subgroups (Subgroup I: RW for 24 h [RW-24]; Subgroup II: RW for 48 h; Subgroup III: Coca-Cola for 24 h [CC-24]; Subgroup IV: Coca-Cola for 48 h [CC-48]; Subgroup V: Distilled water for 24 h [DW-24]; Subgroup VI: Distilled water for 48 h [DW-48]). All the samples were immersed in respective drinks for a period of 24 h, and color differences were measured using ultraviolet spectrophotometer. Once again, all the samples were immersed for another 24 h in the same drinks. After 48 h, the color change of the samples was measured. Measurements were made according to the CIE L × a × b × color space relative to the CIE standard illuminant D65. The color changes of the specimens were evaluated using the following formula: Statistical analysis was performed. The data were analyzed using the one-way ANOVA and t -test at a significance level of 0.05. Color stability of MH composite resin was found to be inferior than the NF resin composite irrespective of immersion medium and time. In RW, the color change observed was maximum for both composite resins followed by Coca-Cola. Immersing the resin composites in distilled water for 24 and 48 h had negligible color change. A 48-h immersion of both composite resins in

  14. Color stability assessment of two different composite resins with variable immersion time using various beverages: An In vitro study

    Directory of Open Access Journals (Sweden)

    M Senthil Kumar

    2017-01-01

    Full Text Available Purpose of the Study: The aim of the study was to evaluate the difference in the color of microhybrid (MH and nanofilled (NF composite resins after 24 and 48 h in beverages such as red wine (RW, Coca-Cola, and distilled water. The specific objective of this study was to investigate the cumulative effect of the colorant solutions on the dental composites. Materials and Methods: MH and NF composite resins (A2 shade were used in this current study. Sixty disk-shaped material specimens (10 mm in diameter × 2 mm in thickness were prepared using a fiber mold (ring, with the desired dimensions. The specimen surfaces were polished using super-snap polishing system. Sixty specimens were divided into two groups of 30 each (Group I: MH resin composite; Group II: NF resin composite. Both the groups divided into six subgroups (Subgroup I: RW for 24 h [RW-24]; Subgroup II: RW for 48 h; Subgroup III: Coca-Cola for 24 h [CC-24]; Subgroup IV: Coca-Cola for 48 h [CC-48]; Subgroup V: Distilled water for 24 h [DW-24]; Subgroup VI: Distilled water for 48 h [DW-48]. All the samples were immersed in respective drinks for a period of 24 h, and color differences were measured using ultraviolet spectrophotometer. Once again, all the samples were immersed for another 24 h in the same drinks. After 48 h, the color change of the samples was measured. Measurements were made according to the CIE L × a × b × color space relative to the CIE standard illuminant D65. The color changes of the specimens were evaluated using the following formula: [INSIDE:1]Statistical analysis was performed. The data were analyzed using the one-way ANOVA and t-test at a significance level of 0.05. Conclusion: Color stability of MH composite resin was found to be inferior than the NF resin composite irrespective of immersion medium and time. In RW, the color change observed was maximum for both composite resins followed by Coca-Cola. Immersing the resin composites in distilled water for 24 and

  15. Dynamic thermo-mechanical properties of various flowable resin composites

    Science.gov (United States)

    Balthazard, Rémy; Vincent, Marin; Dahoun, Abdessellam; Mortier, Eric

    2016-01-01

    Background This study compared the storage modulus (E’), the loss modulus (E’’) and the loss tangent (tan δ) of various flowable resin composites. Material and Methods Grandio Flow (GRF), GrandioSo Heavy Flow (GHF), Filtek Supreme XTE (XTE) and Filtek Bulk Fill (BUL) flowable resins and Clinpro Sealant (CLI) ultra-flowable pit and fissure sealant resin were used. 25 samples were tested using a dynamical mechanical thermal analysis system in bending mode. Measurements were taken within a temperature range of 10 to 55°C. The results were statistically analyzed using mixed-effect and repeated-measure analysis of variance followed by paired multiple comparisons. Results For all the materials, the E’ values decrease with temperature, whereas the tan δ values increase. Irrespective of the temperature, GHF and GRF present E’ and E’’ values significantly higher than all the other materials and CLI presents values significantly lower than all the other materials. Observation of the values for all the materials reveals a linear progression of the tan δ values with temperature. Conclusions A variation in temperature within a physiological range generates modifications in mechanical properties without damaging the material, however. Filler content in volume terms appears to be the crucial parameter in the mechanical behavior of tested materials. Key words:Dynamic mechanical thermal analysis, elastic modulus, filler content, flowable resin composites, loss modulus, loss tangent. PMID:27957266

  16. Silicone Resin Applications for Ceramic Precursors and Composites

    Directory of Open Access Journals (Sweden)

    Masaki Narisawa

    2010-06-01

    Full Text Available This article reviews the applications of silicone resins as ceramic precursors. The historical background of silicone synthesis chemistry is introduced to explain the production costs and supply availability of various silicones. Thermal degradation processes of silicones are classified in terms of the main chain structure and cyclic oligomer expulsion process, which determine the resulting ceramic yield and the chemical composition. The high temperature decomposition of Si-O-C beyond 1,400 °C in an inert atmosphere and formation of a protective silica layer on material surfaces beyond 1,200 °C in an oxidative atmosphere are discussed from the viewpoints of the wide chemical composition of the Si-O-C materials. Applications of the resins for binding agents, as starting materials for porous ceramics, matrix sources with impregnation, fiber spinning and ceramic adhesions are introduced. The recent development of the process of filler or cross-linking agent additions to resin compounds is also introduced. Such resin compounds are useful for obtaining thick coatings, MEMS parts and bulk ceramics, which are difficult to obtain by pyrolysis of simple organometallic precursors without additives.

  17. Amalgam and composite posterior restorations: curriculum versus practice in operative dentistry at a US dental school.

    Science.gov (United States)

    Ottenga, Marc E; Mjör, Ivar

    2007-01-01

    This study recorded the number of preclinical lecture and simulation laboratory sessions spent teaching the preparation and placement of amalgam and resin composite posterior restorations. These data were compared to the use of both materials in the operative clinic as placed by third- and fourth-year students. The number of posterior restorations inserted by the students, expressed as a function of the number of restoration surfaces, was also evaluated. The results show that the teaching of posterior restorations pre-clinically has consistently favored amalgam 2.5 to 1 during the last three years. However, clinically, resin composite is being used for posterior restorations 2.3 times more often than amalgam. The only instance that favored amalgam over composite during the last year was in the placement of four surface posterior restorations. This shift in emphasis from amalgam to composite needs to be addressed within dental educational institutions so that newly graduated dentists are prepared to place composite restorations properly.

  18. Profile of Fluoride Release from a Nanohybrid Composite Resin

    Directory of Open Access Journals (Sweden)

    Raquel Assed Bezerra Silva

    2015-02-01

    Full Text Available The aim of this study was to evaluate in vitro the amount and profile of fluoride release from a fluoride-containing nanohybrid composite resin (Tetric® N-Ceram by direct potentiometry. Thirty specimens (5 mm diameter x 3 mm high; n=10/material were made of Tetric® N-Ceram, Vitremer® resin-modified glass ionomer cement (RMGIC (positive control or Filtek® Z350 nanofill composite resin (negative control. The specimens were stored individually in plastic tubes containing 1 mL of artificial saliva at 37°C, which was daily renewed during 15 days. At each renewal of saliva, the amount of fluoride ions released in the solution was measured using a fluoride ion-selective electrode with ion analyzer, and the values obtained in mV were converted to ppm (µg/mL. Data were analyzed statistically by ANOVA and Tukey’s post-hoc test at a significance level of 5%. The results showed that the resins Tetric® N-Ceram and Filtek® Z350 did not release significant amounts of fluoride during the whole period of evaluation (p>0.05. Only Vitremer® released significant amounts of fluoride ions during the 15 days of the experiment, with greater release in first 2 days (p0.05. In conclusion, the nanohybrid composite resin Tetric® N-Ceram did not present in vitro fluoride-releasing capacity throughout the 15 days of study.

  19. Resin infusion of layered metal/composite hybrid and resulting metal/composite hybrid laminate

    Science.gov (United States)

    Cano, Roberto J. (Inventor); Grimsley, Brian W. (Inventor); Weiser, Erik S. (Inventor); Jensen, Brian J. (Inventor)

    2009-01-01

    A method of fabricating a metal/composite hybrid laminate is provided. One or more layered arrangements are stacked on a solid base to form a layered structure. Each layered arrangement is defined by a fibrous material and a perforated metal sheet. A resin in its liquid state is introduced along a portion of the layered structure while a differential pressure is applied across the laminate structure until the resin permeates the fibrous material of each layered arrangement and fills perforations in each perforated metal sheet. The resin is cured thereby yielding a metal/composite hybrid laminate.

  20. Interactions between resin monomers and commercial composite resins with human saliva derived esterases.

    Science.gov (United States)

    Jaffer, F; Finer, Y; Santerre, J P

    2002-04-01

    Cholesterol esterase (CE) and pseudocholinesterase (PCE) have been reported to degrade commercial and model composite resins containing bisphenylglycidyl dimethacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA) or the latter in combination with urethane modified BisGMA monomer systems. In addition, human saliva has been shown to contain esterase like activities similar to CE and PCE. Hence, it was the aim of the current study to determine to what extent human saliva could degrade two common commercial composite resins (Z250 from 3M Inc. and Spectrum TPH from L.D. Caulk) which contain the above monomer systems. Saliva samples from different volunteers were collected, processed, pooled, and freeze-dried. TEGDMA and BisGMA monomers were incubated with human saliva derived esterase activity (HSDEA) and their respective hydrolysis was monitored using high performance liquid chromatography (HPLC). Both monomers were completely hydrolyzed within 25 h by HSDEA. Photopolymerized composites were incubated with buffer or human saliva (pH 7.0 and 37 C) for 2, 8 and 16 days. The incubation solutions were analyzed using HPLC and mass spectrometry. Surface morphology characterization was carried out using scanning electron microscopy. Upon biodegradation, the Z250 composite yielded higher amounts of BisGMA and TEGDMA related products relative to the TPH composite. However, there were higher amounts of ethoxylated bis-phenol A released from the TPH material. In terms of total mass of products released, human saliva demonstrated a greater ability to degrade Z250. In summary, HSDEA has been shown to contain esterase activities that can readily catalyze the biodegradation of current commercial composite resins.

  1. Boron/aluminum graphite/resin advanced fiber composite hybrids

    Science.gov (United States)

    Chamis, C. C.; Lark, R. F.; Sullivan, T. L.

    1975-01-01

    Fabrication feasibility and potential of an adhesively bonded metal and resin matrix fiber-composite hybrid are determined as an advanced material for aerospace and other structural applications. The results show that using this hybrid concept makes possible a composite design which, when compared with nonhybrid composites, has greater transverse strength, transverse stiffness, and impact resistance with only a small penalty on density and longitudinal properties. The results also show that laminate theory is suitable for predicting the structural response of such hybrids. The sequence of fracture modes indicates that these types of hybrids can be readily designed to meet fail-safe requirements.

  2. Nanotechnology strategies for antibacterial and remineralizing composites and adhesives to tackle dental caries

    Science.gov (United States)

    Cheng, Lei; Zhang, Ke; Weir, Michael D; Melo, Mary Anne S; Zhou, Xuedong; Xu, Hockin HK

    2015-01-01

    Dental caries is the most widespread disease and an economic burden. Nanotechnology is promising to inhibit caries by controlling biofilm acids and enhancing remineralization. Nanoparticles of silver were incorporated into composites/adhesives, along with quaternary ammonium methacrylates (QAMs), to combat biofilms. Nanoparticles of amorphous calcium phosphate (NACP) released calcium/phosphate ions, remineralized tooth-lesions and neutralized acids. By combining NAg/QAM/NACP, a new class of composites and adhesives with antibacterial and remineralization double benefits was developed. Various other nanoparticles including metal and oxide nanoparticles such as ZnO and TiO2, as well as polyethylenimine nanoparticles and their antibacterial capabilities in dental resins were also reviewed. These nanoparticles are promising for incorporation into dental composites/cements/sealants/bases/liners/adhesives. Therefore, nanotechnology has potential to significantly improve restorative and preventive dentistry. PMID:25723095

  3. Surface roughness of composite resins subjected to hydrochloric acid.

    Science.gov (United States)

    Roque, Ana Carolina Cabral; Bohner, Lauren Oliveira Lima; de Godoi, Ana Paula Terossi; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

    2015-01-01

    The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

  4. Survival of anterior cantilevered all-ceramic resin-bonded fixed dental prostheses made from zirconia ceramic.

    Science.gov (United States)

    Sasse, Martin; Kern, Matthias

    2014-06-01

    This study evaluated the clinical outcome of all-ceramic resin-bonded fixed dental prostheses (RBFDPs) with a cantilevered single-retainer design made from zirconia ceramic. Forty-two anterior RBFDPs with a cantilevered single-retainer design were made from yttrium oxide-stabilized zirconium oxide ceramic. RBFDPs were inserted using Panavia 21 TC as luting agent after air-abrasion of the ceramic bonding surface. During a mean observation time of 61.8 months two debondings occurred. Both RBFDPs were rebonded using Panavia 21 TC and are still in function. A caries lesion was detected at one abutment tooth during recall and was treated with a composite filling. Therefore, the overall six-year failure-free rate according to Kaplan-Meier was 91.1%. If only debonding was defined as failure the survival rate increased to 95.2%. Since all RBFDPs are still in function the overall survival rate was 100% after six years. Cantilevered zirconia ceramic RBFDPs showed promising results within the observation period. Single-retainer resin-bonded fixed dental prostheses made from zirconia ceramic show very good mid-term clinical survival rates. They should therefore be considered as a viable treatment alternative for the replacement of single missing anterior teeth especially as compared to an implant therapy. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Impact of head and neck radiotherapy on the mechanical behavior of composite resins and adhesive systems: A systematic review.

    Science.gov (United States)

    Madrid Troconis, Cristhian Camilo; Santos-Silva, Alan Roger; Brandão, Thaís Bianca; Lopes, Marcio Ajudarte; de Goes, Mario Fernando

    2017-11-01

    To analyze the evidence regarding the impact of head and neck radiotherapy (HNRT) on the mechanical behavior of composite resins and adhesive systems. Searches were conducted on PubMed, Embase, Scopus and ISI Web of Science databases using "Radiotherapy", "Composite resins" and "Adhesive systems" as keywords. Selected studies were written in English and assessed the mechanical behavior of composite resins and/or adhesive systems when bonding procedure was conducted before and/or after a maximum radiation dose ≥50Gy, applied under in vitro or in vivo conditions. In total, 115 studies were found but only 16 were included, from which five evaluated the effect of in vitro HNRT on microhardness, wear resistance, diametral tensile and flexural strength of composite resins, showing no significant negative effect in most of reports. Regarding bond strength of adhesive systems, 11 studies were included from which five reported no meaningful negative effect when bonding procedure was conducted before simulated HNRT. Conversely, five studies showed that bond strength diminished when adhesive procedure was done after in vitro radiation therapy. Only two studies about dental adhesion were conducted after in vivo radiotherapy but the results were not conclusive. The mechanical behavior of composite resins and adhesive systems seems not to be affected when in vitro HNRT is applied after bonding procedure. However, bond strength of adhesive systems tends to decrease when simulated radiotherapy is used immediately before bonding procedure. Studies assessing dentin bond strength after in-vivo HNRT were limited and controversial. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  6. The Influence of Hydroxylated Carbon Nanotubes on Epoxy Resin Composites

    Directory of Open Access Journals (Sweden)

    Jiaoxia Zhang

    2012-01-01

    Full Text Available Hydroxylated multiwall carbon nanotubes (MWNTs/epoxy resin nanocomposites were prepared with ultrasonic dispersion and casting molding. The effect of hydroxylated MWNTs content on reactive activity of composites is discussed. Then the flexural and electrical properties were studied. Transmission electron microscope was employed to characterize the microstructure of nanocomposites. As a result, the reactive activity of nanocomposites obtained increases with the increasing content of MWNTs. When MWNTs content of the composites is 1 wt%, as compared to neat resin, the flexural strength increases from 143 Mpa to 156 MPa, the modulus increases from 3563 Mpa to 3691 MPa, and the volume and surface resistance of nanocomposites decrease by two orders of magnitude, respectively.

  7. Resin composites: Modulus of elasticity and marginal quality.

    Science.gov (United States)

    Benetti, Ana R; Peutzfeldt, Anne; Lussi, Adrian; Flury, Simon

    2014-09-01

    To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity but quite similar polymerization contraction. MOD cavities (n=30) were prepared in extracted premolars, restored and then subjected to thermocyclic and mechanical loading. Marginal quality of the restorations before and after loading was analyzed on epoxy replicas under a scanning electron microscope. The percentage of gap-free margins and occurrence of paramarginal fractures were registered. Modulus of elasticity and polymerization contraction were analyzed with parametric and margins with nonparametric ANOVA and post hoc Tukey HSD or Wilcoxon rank-sum tests, respectively. The number of paramarginal fractures was analyzed with exact Fisher tests (α=0.05). Grandio demonstrated significantly more gap-free enamel margins than Charisma and Filtek Supreme XTE, before and after loading (p0.05). No significant effect of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (pGrandio when compared to Charisma (p=0.008). The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. The results from this study suggest that the marginal quality of restorations can be improved by the selection of a resin composite with modulus of elasticity close to that of dentine, although an increase in paramarginal enamel fractures can result as a consequence. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Effects of polishing procedures on color stability of composite resins.

    Science.gov (United States)

    Güler, Ahmet Umut; Güler, Eda; Yücel, Ali Cağin; Ertaş, Ertan

    2009-01-01

    The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme). Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd), polishing discs then diamond polishing paste (PdP), polishing discs then a liquid polishing system (Biscover) (PdB), and combinations of these (PdPB) were used. Unpolished specimens served as the control (C). The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DeltaE*) were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (alpha=0.05). The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme). The posterior (Filtek P60) and universal (Filtek Z250) composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA), were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme) and universal (Quadrant LC) composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  9. Effects of polishing procedures on color stability of composite resins

    Directory of Open Access Journals (Sweden)

    Ahmet Umut Güler

    2009-04-01

    Full Text Available The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme. Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd, polishing discs then diamond polishing paste (PdP, polishing discs then a liquid polishing system (Biscover (PdB, and combinations of these (PdPB were used. Unpolished specimens served as the control (C. The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DE* were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (a=0.05. The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme. The posterior (Filtek P60 and universal (Filtek Z250 composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA, were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme and universal (Quadrant LC composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  10. COMPOSITE RESIN BOND STRENGTH TO ETCHED DENTINWITH ONE SELF PRIMING ADHESIVE

    Directory of Open Access Journals (Sweden)

    P SAMIMI

    2002-09-01

    Full Text Available Introduction. The purpose of this study was to compare shear bond strength of composite resins to etched dentin in both dry and wet dentin surface with active and inactive application of a single-bottle adhesive resin (Single Bond, 3M Dental products. Methods. Fourthy four intact human extracted molars and premolars teeth were selected. The facial surfaces of the teeth were grounded with diamond bur to expose dentin. Then specimens were divided into four groups of 11 numbers (9 Molars and 2 Premolars. All the samples were etched with Phosphoric Acid Gel 35% and then rinsed for 10 seconds. The following stages were carried out for each group: Group I (Active-Dry: After rinsing, air drying of dentin surface for 15 seconds, active priming of adhesive resin for 15 seconds, air drying for 5 seconds, the adhesive resin layer was light cured for 10 seconds. Group III (Inactive-Dry:After rinsing, air drying of dentin surface for 15 seconds, adhesive resin was applied and air dryied for 5 seconds, the adhesive layer was light cured for 10 seconds. Group III (Active-Wet:After rinsing, removal of excess water of dentin surface with a cotton roll, active priming of adhesive resin for 15 seconds and air drying for 5 seconds, the adhesive layer was light cured for 10 seconds. Group IV (Inactive-Wet:After rinsing, removal of excess water of dentin surface with a cotton roll, the adhesive resin was applied and air dryied for 5 seconds and then cured for 10 seconds. After adhesive resin application, composite resin (Z250, 3M Dental products was applied on prepared surface with cylindrical molds (with internal diameter of 2.8mm, & height of 5mm and light-cured for 100 seconds (5x20s. The samples were then thermocycled. They were located in 6±3c water .temperature for 10 seconds and then 15 seconds in inviromental temperature, 10s in 55±3c water temperature and then were located at room temperature for 15s. This test was repeated for 100s. All of the specimens

  11. Evaluation of inorganic particles of composite resins with nanofiller content.

    Science.gov (United States)

    Mota, Eduardo Gonçalves; Hörlle, Lucas; Oshima, Hugo Mitsuo; Hirakata, Luciana Mayumi

    2012-01-01

    The purposes of this study were evaluate by energy dispersed X-ray (EDS) and scanning electron microscopy (SEM) the inorganic particles of three nanofilled composite resins, comparing particles sizes, shape and composition, and the filler weight content by thermogravimetric analyzes (TGA). Three composite resins classified as nanofilled were selected to this study: Esthet-X; Grandio; Filtek Supreme XT. The shade was standardized (A2) for enamel (E) or dentin (D). Ten samples with 20 mg (±10 mg) of each composite resin were submitted to thermogravimetric analyzes (TGA) in order to record the filler weight content (wt%). The amount of inorganic phase ranged from 75.75 to 87 wt%, to Esthet-X (D) and Grandio (D), respectively. The filler composition was analyzed by energy dispersed X-ray (EDS), and the size and shape were evaluated by scanning electron microscopy (SEM). The filler average size (µm) obtained by SEM were: Esthet-X (E) 1.16; Esthet-X (D) 1.39; Filtek Supreme XT (E) 0.6 (nanocluster); Filtek Supreme XT (D) 1.14 (nanocluster); Grandio (E) 2.05 and Grandio (D) 3.1. Silica (SiO2), Ba and Al were observed through EDS. The shape of Esthet-X and Grandio fillers showed similar characteristics with high quantity of irregular inorganic particles and heterogeneous filler. However, Filtek Supreme XT showed spherical and regular particles with homogeneous distribution and sizes. Based in the analysis of nanofilled composites inorganic phase, inconsistencies of weight content, composition, shape and size can be stated between the literature and manufacturer's instructions.

  12. Radiopacity of bulk fill flowable resin composite materials | Yildirim ...

    African Journals Online (AJOL)

    Objectives: The purpose of this study was to evaluate the radiopacity of currently marketed bulk fill flowable dental composite materials (Beautifil Bulk Flowable, SDR Flow, Filtek Bulk Fill Flow, and x‑tra Base Bulk Fill). Materials and Methods: Six specimens of each material with a thickness of 1 mm were prepared, and ...

  13. Radiopacity of bulk fill flowable resin composite materials

    African Journals Online (AJOL)

    2015-08-23

    Aug 23, 2015 ... Objectives: The purpose of this study was to evaluate the radiopacity of currently marketed bulk fill flowable dental composite materials (Beautifil Bulk Flowable, SDR Flow, Filtek Bulk Fill Flow, and x‑tra Base Bulk Fill). Materials and Methods: Six specimens of each material with a thickness of 1 mm were ...

  14. Effect of surface treatments on the bond strengths of facing composite resins to zirconia copings.

    Science.gov (United States)

    Tsumita, M; Kokubo, Y; Kano, T

    2012-09-01

    The present study evaluated and compared the bond strength between zirconia and facing composite resin using different surface conditioning methods before and after thermocycling. Four primers, three opaque resins, and two facing composite resins were used, and 10 surface treatment procedures were conducted. The bond strength was measured before and after 4,000 cycles of thermocycling. The mean values of each group were statistically analyzed using one-way analysis of variance (ANOVA). The bond strengths of facing composite resins to zirconia after various treatments varied depending on the primers, opaque resins, body resins, and thermocycling. The application of primers and opaque resins to the zirconia surface after sandblasting is expected to yield strong bond strength of the facing composite resin (Estenia CG&B) even after thermocycling.

  15. Shear bond strength of a self‑etched resin cement to an indirect ...

    African Journals Online (AJOL)

    ... however there were not statistical difference among the tested surface treatment methods. Conclusion: In Shear bond strength of resin, cement was independent of the surface conditioning methods applied on tested indirect resin composite. Key words: Composite resins, dental bonding, resin cements, surface properties ...

  16. Mimicking the Nanostructure for Perfect Dental Treatment

    OpenAIRE

    Tamer M. Hamdy

    2017-01-01

    Nanotechnology is set to alter clinical dental practice. In no distant future, dental restorative materials will become very accurate, the same as natural one and smart. Thus all efforts should be done to achieve dental restorative materials in nanoscale including dental medicament, resin composite, cements, sealers, ceramics, impression materials, remineralizing agent, dentures, bone replacement agent,root fillings and dental implant materials.

  17. Reconstruction of attached soft tissue around dental implants by acelluar dermal matrix grafts and resin splint

    Science.gov (United States)

    Liu, Changying; Su, Yucheng; Tan, Baosheng; Ma, Pan; Wu, Gaoyi; Li, Jun; Geng, Wei

    2014-01-01

    Objectives: The purpose of this study was to recommend a new method using acellular dermal matrix graft and resin splint to reconstruct the attached soft tissue around dental implants in patients with maxillofacial defects. Materials and methods: Total 8 patients (3 male and 5 female patients) diagnosed with maxillofacial defects and dentition defects caused by tumors, fractures or edentulous jaw, were selected for this study. Dental implants were routinely implanted at the edentulous area. Acellular dermal matrix heterografts and resin splint were used to increase the attached soft tissue. The width of attached gingiva in the labial or buccal surface at edentulous area was measured before surgical procedures and after the completion of superstructures. Paired t-test was applied to assess the change of quantitative variables. All tests were 2-tailed, and P implants could be reconstructed one month after the completion of surgical procedures, and the epithelial cuff around the implant neck established very well. The width of attached gingival tissue in the patients increased significantly from a mean of 0.61 ± 0.75 mm to 6.25 ± 1.04 mm. The patients were fully satisfied with the esthetic and functional results achieved. Conclusions: The acellular dermal matrix graft could be used to increase the attached gingiva around dental implants in these patients with maxillofacial defects. The resin splint could facilitate the healing of graft. PMID:25663964

  18. CURING OF POLYMERIC COMPOSITES USING MICROWAVE RESIN TRANSFER MOULDING (RTM

    Directory of Open Access Journals (Sweden)

    R. YUSOFF

    2007-08-01

    Full Text Available The main objective of this work is to compare the difference between microwave heating and conventional thermal heating in fabricating carbon/epoxy composites. Two types of epoxy resin systems were used as matrices, LY5052-HY5052 and DGEBA-HY917-DY073. All composite samples were fabricated using resin transfer moulding (RTM technique. The curing of the LY5052-HY5052-carbon and the DGEBA-HY917-DY073-carbon composite systems, were carried out at 100 °C and 120 °C, respectively. Microwave heating showed better temperature control than conventional heating, however, the heating rate of the microwave cured samples were slower than the conventionally cured samples. This was attributed to the lower power (250 W used when heating with microwaves compared to 2000 W used in conventional heating. Study of thermal characteristics as curing progressed showed that the polymerisation reaction occurred at a faster rate during microwave curing than in conventional curing for both the DGEBA and the LY/HY5052 carbon composite systems. The actual cure cycle was reduced from 60 minutes to 40 minutes when using microwaves for curing DGEBA-carbon composites. As for LY/HY5052-carbon composites, the actual cure cycle was reduced from 3 hours to 40 minutes. Both conventional and microwave heating yielded similar glass transition temperatures (120 °C for DGEBA systems and 130 °C for LY/HY5052 systems. Microwave cured composites had higher void contents than conventionally cured composites (2.2-2.8% and 1.8-2.4% for DGEBA and LY/HY5052 microwave cured composites, respectively, compared to 0.2-0.4% for both DGEBA and LY/HY5052 thermally cured composites. C-scan traces showed that all composites, regardless of methods of curing, had minimal defects.

  19. Dental composite restorations and psychosocial function in children.

    Science.gov (United States)

    Maserejian, Nancy N; Trachtenberg, Felicia L; Hauser, Russ; McKinlay, Sonja; Shrader, Peter; Tavares, Mary; Bellinger, David C

    2012-08-01

    Resin-based dental materials may intraorally release their chemical components and bisphenol A. The New England Children's Amalgam Trial found that children randomized to amalgam had better psychosocial outcomes than those assigned to composites for posterior tooth restorations. The objective of this study was to examine whether greater exposure to dental composites is associated with psychosocial problems in children. Analysis of treatment-level data from the New England Children's Amalgam Trial, a 2-group randomized safety trial comparing amalgam with the treatment plan of bisphenol A-glycidyl methacrylate (bisGMA)-based composite and urethane dimethacrylate-based polyacid-modified composite (compomer), among 534 children aged 6 to 10 years at baseline. Psychosocial function at follow-up (n = 434) was measured by using the self-reported Behavior Assessment System for Children (BASC-SR) and parent-reported Child Behavior Checklist (CBCL). Children with higher cumulative exposure to bisGMA-based composite had poorer follow-up scores on 3 of 4 BASC-SR global scales: Emotional Symptoms (β = 0.8, SE = 0.3, P = .003), Clinical Maladjustment (β = 0.7, SE = 0.3, P = .02), and Personal Adjustment (β = -0.8, SE = 0.2, P = .002). Associations were stronger with posterior-occlusal (chewing) surfaces, where degradation of composite was more likely. For CBCL change, associations were not statistically significant. At-risk or clinically significant scores were more common among children with greater exposure for CBCL Total Problem Behaviors (16.3% vs 11.2%, P-trend = .01) and numerous BASC-SR syndromes (eg, ≥ 13 vs 0 surface-years, Interpersonal Relations 13.7% vs 4.8%, P-trend = .01). No associations were found with compomer, nor with amalgam exposure levels among children randomized to amalgam. Greater exposure to bisGMA-based dental composite restorations was associated with impaired psychosocial function in children, whereas no adverse psychosocial outcomes were

  20. Non-destructive evaluation of teeth restored with different composite resins using synchrotron based micro-imaging.

    Science.gov (United States)

    Fatima, A; Kulkarni, V K; Banda, N R; Agrawal, A K; Singh, B; Sarkar, P S; Tripathi, S; Shripathi, T; Kashyap, Y; Sinha, A

    2016-01-01

    Application of high resolution synchrotron micro-imaging in microdefects studies of restored dental samples. The purpose of this study was to identify and compare the defects in restorations done by two different resin systems on teeth samples using synchrotron based micro-imaging techniques namely Phase Contrast Imaging (PCI) and micro-computed tomography (MCT). With this aim acquired image quality was also compared with routinely used RVG (Radiovisiograph). Crowns of human teeth samples were fractured mechanically involving only enamel and dentin, without exposure of pulp chamber and were divided into two groups depending on the restorative composite materials used. Group A samples were restored using a submicron Hybrid composite material and Group B samples were restored using a Nano-Hybrid restorative composite material. Synchrotron based PCI and MCT was performed with the aim of visualization of tooth structure, composite resin and their interface. The quantitative and qualitative comparison of phase contrast and absorption contrast images along with MCT on the restored teeth samples shows comparatively large number of voids in Group A samples. Quality assessment of dental restorations using synchrotron based micro-imaging suggests Nano-Hybrid resin restorations (Group B) are better than Group A.

  1. Direct composite resin fillings versus amalgam fillings for permanent or adult posterior teeth.

    Science.gov (United States)

    Rasines Alcaraz, M Graciela; Veitz-Keenan, Analia; Sahrmann, Philipp; Schmidlin, Patrick Roger; Davis, Dell; Iheozor-Ejiofor, Zipporah

    2014-03-31

    Amalgam has been the traditional material for filling cavities in posterior teeth for the last 150 years and, due to its effectiveness and cost, amalgam is still the restorative material of choice in certain parts of the world. In recent times, however, there have been concerns over the use of amalgam restorations (fillings), relating to the mercury release in the body and the environmental impact following its disposal. Resin composites have become an esthetic alternative to amalgam restorations and there has been a remarkable improvement of its mechanical properties to restore posterior teeth.There is need to review new evidence comparing the effectiveness of both restorations. To examine the effects of direct composite resin fillings versus amalgam fillings for permanent posterior teeth, primarily on restoration failure. We searched the Cochrane Oral Health Group's Trials Register (to 22 October 2013), the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2013, Issue 9), MEDLINE via OVID (1946 to 22 October 2013), EMBASE via OVID (1980 to 22 October 2013), and LILACs via BIREME Virtual Health Library (1980 to 22 October 2013). We applied no restrictions on language or date of publication when searching the electronic databases. We contacted manufacturers of dental materials to obtain any unpublished studies. Randomized controlled trials comparing dental resin composites with dental amalgams in permanent posterior teeth. We excluded studies having a follow-up period of less than three years. We used standard methodological procedures expected by The Cochrane Collaboration. Of the 2205 retrieved references, we included seven trials (10 articles) in the systematic review. Two trials were parallel group studies involving 1645 composite restorations and 1365 amalgam restorations (921 children) in the analysis. The other five trials were split-mouth studies involving 1620 composite restorations and 570 amalgam restorations in an unclear

  2. Comparative evaluation of shear bond strength of conventional composite resin and nanocomposite resin to sandblasted primary anterior stainless steel crown.

    Science.gov (United States)

    Khatri, A; Nandlal, B

    2007-01-01

    To evaluate and compare the shear bond strength of conventional composite resin and nanocomposite resin to sandblasted primary anterior stainless steel crown. The study samples consisted of 30 primary anterior stainless steel crowns (Unitek TM, size R4), embedded in resin blocks with crown, in test groups of 15 samples each. Mounting of the crown was done using resin block with one crown each. Sandblasting was done and the bonding agent Prime and Bond NT (Dentsply) was applied on the labial surface of the primary anterior sandblasted crown. The composite resin and nanocomposite resin were placed into the well of Teflon jig and bonded to Stainless Steel Crowns. The cured samples were placed in distilled water and stored in incubator at 37 degrees C for 48 hours. Shear bond strength was measured using universal testing machine (Hounsefield U.K. Model, with a capacity of 50 KN). Independent sample 't' test revealed a nonsignificant (P resin and nanocomposite resin had statistically similar mean shear bond strength, with nanocomposite having little more strength compared to conventional composite.

  3. Process for curing ionizing radiation-highly sensitive resin composition

    International Nuclear Information System (INIS)

    Araki, K.; Sasaki, T.; Tabei, K.; Goto, K.

    1979-01-01

    A process is described for curing a radiation curable composition consisting essentially of (a) an amide represented by the formula R,CONR 2 R 3 and (b) an unsaturated polyester resin by irradiating the composition with an ionizing radiation. R 1 is H, an alkyl groups having from 1 to 17 carbon atoms or an alkenyl groups having from 1 to 17 carbon atoms, and R 2 and R 3 are each -H, -CH 3 , or -CH 2 OH. R 1 and R 2 taken together represent alkylene having 2 to 5 carbon atoms

  4. Longevity of dental amalgam in comparison to composite materials

    Directory of Open Access Journals (Sweden)

    Windisch, Friederike

    2008-11-01

    Full Text Available Health political background: Caries is one of the most prevalent diseases worldwide. For (direct restaurations of carious lesions, tooth-coloured composite materials are increasingly used. The compulsory health insurance pays for composite fillings in front teeth; in posterior teeth, patients have to bear the extra cost. Scientific background: Amalgam is an alloy of mercury and other metals and has been used in dentistry for more than one hundred and fifty years. Composites consist of a resin matrix and chemically bonded fillers. They have been used for about fifty years in front teeth. Amalgam has a long longevity; the further development of composites has also shown improvements regarding their longevity. Research questions: This HTA-report aims to evaluate the longevity (failure rate, median survival time (MST, median age of direct amalgam fillings in comparison to direct composite fillings in permanent teeth from a medical and economical perspective and discusses the ethical, legal and social aspects of using these filling materials. Methods: The systematic literature search yielded a total of 1,149 abstracts. After a two-step selection process based on defined criteria 25 publications remained to be assessed. Results: The medical studies report a longer longevity for amalgam fillings than for composite fillings. However, the results of these studies show a large heterogeneity. No publication on the costs or the cost-effectiveness of amalgam and composite fillings exists for Germany. The economic analyses (NL, SWE, GB report higher costs for composite fillings when longevity is assumed equal (for an observation period of five years or longer for amalgam compared to composite fillings. These higher costs are due to the higher complexity of placing composite fillings. Discussion: Due to different study designs and insufficient documentation of study details, a comparison of different studies on longevity of direct amalgam and composite

  5. Longevity of dental amalgam in comparison to composite materials.

    Science.gov (United States)

    Antony, Katja; Genser, Dieter; Hiebinger, Cora; Windisch, Friederike

    2008-11-13

    Caries is one of the most prevalent diseases worldwide. For (direct) restaurations of carious lesions, tooth-coloured composite materials are increasingly used. The compulsory health insurance pays for composite fillings in front teeth; in posterior teeth, patients have to bear the extra cost. Amalgam is an alloy of mercury and other metals and has been used in dentistry for more than one hundred and fifty years. Composites consist of a resin matrix and chemically bonded fillers. They have been used for about fifty years in front teeth. Amalgam has a long longevity; the further development of composites has also shown improvements regarding their longevity. This HTA-report aims to evaluate the longevity (failure rate, median survival time (MST), median age) of direct amalgam fillings in comparison to direct composite fillings in permanent teeth from a medical and economical perspective and discusses the ethical, legal and social aspects of using these filling materials. The systematic literature search yielded a total of 1,149 abstracts. After a two-step selection process based on defined criteria 25 publications remained to be assessed. The medical studies report a longer longevity for amalgam fillings than for composite fillings. However, the results of these studies show a large heterogeneity. No publication on the costs or the cost-effectiveness of amalgam and composite fillings exists for Germany. The economic analyses (NL, SWE, GB) report higher costs for composite fillings when longevity is assumed equal (for an observation period of five years) or longer for amalgam compared to composite fillings. These higher costs are due to the higher complexity of placing composite fillings. Due to different study designs and insufficient documentation of study details, a comparison of different studies on longevity of direct amalgam and composite fillings in posterior teeth is difficult. Apart from the difficulties in conducting a randomized, controlled long-term study

  6. Temperature-dependent polymerization shrinkage stress kinetics of resin-composites.

    Science.gov (United States)

    Watts, D C; Alnazzawi, A

    2014-06-01

    To determine temperature dependence of shrinkage stress kinetics for a set of resin composites formulated with dimethacrylate monomer matrices. Six representative resin composites with a range of resin matrices were selected. Two of them were considered as low shrinking resin composites: Kalore and Venus Diamond. The shrinkage stress kinetics at 23°C and 37°C were measured continuously using a Bioman instrument for 60min. Stress levels between materials were compared at two intervals: 2min and 60min. Specimen temperatures were controlled by a newly designed heating device. Stress measurements were monitored for 1h, after irradiation for 40s at 550mW/cm(2) (energy density=22J/cm(2)). Three specimens (n=3) were used at each temperature per material. Shrinkage stress at 23°C ranged from 2.93MPa to 4.71MPa and from 3.57MPa to 5.42MPa for 2min and 60min after photo-activation, respectively. The lowest stress-rates were recorded for Kalore and Venus Diamond (0.34MPas(-1)), whereas the highest was recorded for Filtek Supreme XTE (0.63MPas(-1)). At 37°C, shrinkage stress ranged from 3.27MPa to 5.35MPa and from 3.36MPa to 5.49MPa for 2min and 60min after photo-activation, respectively. Kalore had the lowest stress-rate (0.44MPas(-1)), whereas Filtek Supreme XTE had the highest (0.85MPas(-1)). Materials exhibited a higher stress at 37°C than 23°C except for Kalore and Venus Diamond. Positive correlations were found between shrinkage stress and stress-rate at 23°C and 37°C (r=0.70 and 0.92, respectively). Resin-composites polymerized at elevated temperature (37°C) completed stress build up more rapidly than specimens held at 23°C. Two composites exhibited atypical reduced stress magnitudes at the higher temperature. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  7. Aesthetic Closure of Maxillary and Mandibular Anterior Spaces Using Direct Composite Resin Build-Ups: A Case Report

    Directory of Open Access Journals (Sweden)

    Schick Simona-Georgiana

    2016-07-01

    Full Text Available The presence of multiple spaces in the anterior aesthetic zone can produce discomfort for patients and its treatment can be difficult for dental professionals. A variety of treatment options are available and these include orthodontic movement, prosthetic indirect restorations or direct composite resin build-ups. Among these, the closure of interdental spaces using composite build-ups combined with orthodontic treatment is considered to be most conservative. This type of treatment has several advantages like the maximum preservation of tooth substance (no tooth preparation, no need for anesthesia, no multiple time-consuming visits, no provisional restorations and also comparably low costs. Clinical Consideration: This case report describes the clinical restorative procedure of direct composite resin build-ups for the closure of multiple anterior spaces.

  8. Double Vacuum Bag Process for Resin Matrix Composite Manufacturing

    Science.gov (United States)

    Hou, Tan-Hung (Inventor); Jensen, Brian J. (Inventor)

    2007-01-01

    A double vacuum bag molding assembly with improved void management and laminate net shape control which provides a double vacuum enviromnent for use in fabricating composites from prepregs containing air and/or volatiles such as reactive resin matrix composites or composites from solvent containing prepregs with non-reactive resins matrices. By using two vacuum environments during the curing process, a vacuum can be drawn during a B-stage of a two-step cycle without placing the composite under significant relative pressure. During the final cure stage, a significant pressure can be applied by releasing the vacuum in one of the two environments. Inner and outer bags are useful for creating the two vacuum environments with a perforated tool intermediate the two. The composite is placed intermediate a tool plate and a caul plate in the first environment with the inner bag and tool plate defining the first environment. The second environment is characterized by the outer bag which is placed over the inner bag and the tool plate.

  9. Does the light source affect the repairability of composite resins?

    Directory of Open Access Journals (Sweden)

    Emel KARAMAN

    2014-08-01

    Full Text Available The aim of this study was to examine the effect of the light source on the microshear bond strength of different composite resins repaired with the same substrate. Thirty cylindrical specimens of each composite resin—Filtek Silorane, Filtek Z550 (3M ESPE, Gradia Direct Anterior (GC, and Aelite Posterior (BISCO—were prepared and light-cured with a QTH light curing unit (LCU. The specimens were aged by thermal cycling and divided into three subgroups according to the light source used—QTH, LED, or PAC (n = 10. They were repaired with the same substrate and a Clearfil Repair Kit (Kuraray. The specimens were light-cured and aged for 1 week in distilled water at 37 °C. The microshear bond strength and failure modes were assessed. There was no significant difference in the microshear bond strength values among the composite resins, except for the Filtek Silorane group that showed significantly lower bond strength values when polymerized with the PAC unit compared to the QTH or LED unit. In conclusion, previously placed dimethacrylate-based composites can be repaired with different light sources; however, if the composite to be repaired is silorane-based, then using a QTH or LED device may be the best option.

  10. One Year Clinical Evaluation of a Low Shrinkage Composite Compared with a Packable Composite Resin: A Randomized Clinical Trial

    Directory of Open Access Journals (Sweden)

    Razieh Hoseinifar

    2017-08-01

    Full Text Available Objectives: The aim of this study was to evaluate the clinical performance of a packable and a low shrinkage methacrylate-based composite after one year.Materials and Methods: In this clinical trial, 50 class I or II restorations were placed in 25 patients. Each patient received two restorations. The tested materials were: (I Filtek P60 + Single Bond 2 and (II Kalore GC + Single Bond 2. The restorations were evaluated by two independent examiners after one week (baseline, six months and one year according to the modified United States Public Health Service (USPHS criteria. The evaluated parameters included color match, marginal adaptation, anatomical form, retention, surface texture, postoperative sensitivity, marginal staining and secondary caries. Data were then analyzed using Friedman and conditional (matched logistic regression tests at P<0.05 level of significance. Results: P60 and Kalore performed similarly at six months and one year (P>0.05. When each composite resin was evaluated independently at baseline and after one year, no statistically significant differences were found except for marginal adaptation (P60 where four restorations were rated Bravo (clinically acceptable. In 8% of restorations, patients expressed postoperative sensitivity.Conclusions: Kalore GC and Filtek P60 showed acceptance clinical performance after one year of service.Keywords: Composite Resins; Dental Marginal Adaptation; Patients

  11. Effect of resin-composite filler particle size and shape on shrinkage-stress.

    Science.gov (United States)

    Satterthwaite, Julian D; Maisuria, Amit; Vogel, Karin; Watts, David C

    2012-06-01

    The aim of this study was to investigate the effect of variations in filler particle size and shape on the polymerization shrinkage-stress kinetics of resin-composites. A model series of 12 VLC resin-composites were studied. The particulate dispersed phase volume fraction was 56.7%: these filler particles were systematically graded in size, and further were either spherical or irregular. A Bioman instrument (cantilever beam method) was employed to determine the shrinkage-stress kinetics following 40s irradiation (600 mW/cm(2)) at 23°C (n=3). All data were captured for 60 min and the final shrinkage-stress calculated. Shrinkage-stress varied between 3.86 MPa (SD 0.14) for S3 (spherical filler particles of 500 nm) and 8.44 MPa (SD 0.41) for I1 (irregular filler particles of 450 nm). The shrinkage-stress values were generally lower for those composites with spherical filler particles than those with irregular filler particles. The differences in shrinkage-stress with filler particle size and shape were statistically significant (pparticles exhibit lower shrinkage-stress values compared to those with irregular filler particles. Shrinkage-stress and shrinkage-stress rate vary in a complex manner with variations in the size of the dispersed phase particles: a hypothesized explanation for the effect of filler particle size and shape is presented. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  12. Protein A chromatography resin lifetime-impact of feed composition.

    Science.gov (United States)

    Pathak, Mili; Rathore, Anurag S; Lintern, Katherine; Bracewell, Daniel G

    2018-01-05

    Adsorbent lifetime during protein A chromatography is not readily predicted or understood, representing a key challenge to be addressed for biopharmaceutical manufacturers. This article focuses on the impact of feed composition on the performance of a typical agarose-based protein A resin across a lifetime of 50 cycles. Cycling studies were performed using three different feed materials with varying levels of feed components including proteases, histones, DNA, and nonhistone proteins. Changes in the process and quality attributes were measured. The DBCs were not seen to vary between conditions although there was a reduction in particle porosity in all cases. Fluorescence spectroscopy and LC-MS/MS were used to identify the contribution and extent of fouling to the observed capacity loss. Residual protein A ligand density and deposition of foulants (HCP, residual mAb, and DNA) varied between the three feed materials. Resins cycled in feed materials containing high concentrations of HCP and histones were seen to have greater extents of capacity loss. The mode of performance loss, capacity loss, or impact on product quality was seen to vary depending on the feed material. The results indicate that feed material composition may be correlated to the rate and mode of resin aging as a basis for improved process understanding. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 2018. © 2018 American Institute of Chemical Engineers.

  13. Influence of colorant solutions in properties of indirect resin composites.

    Science.gov (United States)

    Dos Santos, Daniela Micheline; De Paula, Adrielle Mendes; Bonatto, Liliane da Rocha; Da Silva, Emily Vivianne Freitas; Vechiato Filho, Aljomar José; Moreno, Amália; Goiato, Marcelo Coelho

    2015-08-01

    To evaluate the influence of colorant solutions on color stability and surface roughness of indirect resin composites submitted to prior immersion in mouthwashes. Five brands of indirect resin composites were assessed: Adoro, Resilab, Cristobal, Sinfony and Epricord. The specimens were immersed in five different solutions (n = 10): four mouthwashes (Listerine, Oral-B, Plax, Periogard) and artificial saliva (control). 60 hours after immersion in mouthwashes, the specimens were exposed to coffee solution. Shade stability and surface roughness were tested by a spectrophotometer and by a profilometer, respectively. A three-way repeated-measures ANOVA was performed. Differences between the values were compared by the Tukey-Kramer test (P color change. Greater color change was observed after immersion in coffee, except for Cristobal. The color change was even higher for specimens previously immersed in mouthwashes. The Epricord resin showed the lowest roughness value and the Cristobal showed the highest value, regardless of the period. The highest roughness change occurred after immersion in Listerine.

  14. Electron Beam Cured Epoxy Resin Composites for High Temperature Applications

    Science.gov (United States)

    Janke, Christopher J.; Dorsey, George F.; Havens, Stephen J.; Lopata, Vincent J.; Meador, Michael A.

    1997-01-01

    Electron beam curing of Polymer Matrix Composites (PMC's) is a nonthermal, nonautoclave curing process that has been demonstrated to be a cost effective and advantageous alternative to conventional thermal curing. Advantages of electron beam curing include: reduced manufacturing costs; significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; and improvement in material handling. In 1994 a Cooperative Research and Development Agreement (CRADA), sponsored by the Department of Energy Defense Programs and 10 industrial partners, was established to advance the electron beam curing of PMC technology. Over the last several years a significant amount of effort within the CRADA has been devoted to the development and optimization of resin systems and PMCs that match the performance of thermal cured composites. This highly successful materials development effort has resulted in a board family of high performance, electron beam curable cationic epoxy resin systems possessing a wide range of excellent processing and property profiles. Hundreds of resin systems, both toughened and untoughened, offering unlimited formulation and processing flexibility have been developed and evaluated in the CRADA program.

  15. Effect of sandblasting, silica coating, and laser treatment on the microtensile bond strength of a dental zirconia ceramic to resin cements.

    Science.gov (United States)

    Mahmoodi, Nasrin; Hooshmand, Tabassom; Heidari, Solmaz; Khoshro, Kimia

    2016-02-01

    The purpose of this in vitro study was to evaluate the effect of laser irradiation as well as other surface treatment methods on the microtensile bond strength of a dental zirconia ceramic to the two types of resin cements. Zirconia ceramic blocks (ICE Zirkon) were sintered according to the manufacturer's instructions and duplicated in resin composites. The ceramic specimens were divided into four groups according to the following surface treatments: no surface treatment (control), sandblasting with alumina, silica coating plus silanization, and Nd:YAG laser irradiation. The specimens were divided equally and then bonded with Panavia F2.0 (self-etching resin cement) and Clearfil SA Luting (self-adhesive resin cement) to the composite blocks. The bonded ceramic-composite blocks were stored in distilled water at 37 °C for 72 h, cut to prepare bar-shaped specimens with a bonding area of approximately 1 mm(2), and thermocycled for 3000 cycles between 5 and 55 °C, and the microtensile bond strengths were measured using a universal testing machine. The data were analyzed by ANOVA and Tukey post hoc test. The results showed that the self-adhesive resin cement used in this study did not improve the microtensile bond strength when the zirconia surface was sandblasted by alumina. The use of the Nd:YAG laser did not enhance the bond strength between the zirconia and both types of resin cements. In addition, silica coating of the zirconia surfaces plus silane application significantly improved the bond strength regardless of the type of resin cement utilized.

  16. Effect of preheat repetition on color stability of methacrylate- and silorane-based composite resins.

    Science.gov (United States)

    Abed Kahnamouei, Mehdi; Gholizadeh, Sarah; Rikhtegaran, Sahand; Daneshpooy, Mehdi; Kimyai, Soodabeh; Alizadeh Oskoee, Parnian; Rezaei, Yashar

    2017-01-01

    Background. The aim of this study was to investigate the effect of preheating methacrylate- and silorane-based composite resins on their color stability up to 40 times at 55‒60°C. Methods. Seventy-six methacrylate and silorane-based composite resin samples, with a diameter of 10 mm and a height of 2 mm, were divided into 4 groups (n=19). After the samples were prepared, their color parameters were determined using a reflective spectrophotometer. The composite resin samples were separately stored in a solution of tea for 40 consecutive days. Then the samples underwent a color determination procedure again using a spectrophotometer and color changes were recorded. Finally two-way ANOVA was used to study the effect of composite temperature on its staining (Pcomposite resin samples compared to non-heated samples at P=0.005 and P=0.029 for silorane-based and Z250 composite resin samples, respectively. Results. Both composite resin type (P=0.014) and preheating (Pcomposite resin samples, up to 55‒60°C for 40 rounds, resulted in more color changes compared with unheated composite resin samples. After storage in a solution of tea the color change rate in the composite resin samples of silorane-based was higher than the Z250 composite resin samples.

  17. Comparison of the resin cement bond strength to an indirect composites treated by Er;YAG laser and sandblast

    Directory of Open Access Journals (Sweden)

    Mansure Mirzaee

    2014-04-01

    Full Text Available   Background and Aims: Indirect composites are designed to overcome the shortcomings of direct composites such as polymerization shrinkage and low degree of conversion. But, good adhesion of resin cements to indirect composites is still difficult. This research was designed to assess the effect of different powers of Er;YAG laser compared with sandblasting. On the micro tensil bond strength of resin cement to indirect composites.   Materials and Methods: Specimens were prepred using dental resin composite (Gradia GC and metallic mold (15×5×5 mm and were cured according to the manufacturer’s instructions. 24 blocks were prepared and randomly divided into 12 groups. G1:no treatment (as control, G 2-6: Er; YAG laser irradiation (2, 3, 4, 5, 6 Watt, G7: sandblast. Two composite blocks were bonded to each other with Panavia F.2. resin cement. The cylindrical sections with dimensions of 1 mm were tested in a microtensile bond strength tester device using 0.5 mm/min speed until fracture points. Data were analyzed using 2-way ANOVA and T-test.   Results: Interaction between lasers irradiation and sandblast treatments were significant (P0.05 whether samples were sandblasted or not. Samples which received 300 mJ of laser showed lower bond strength compared with no laser treatment. Other groups showed no significant difference (P>0.05.   Conclusion: It seems that application of sandblast with proper variables, is a good way to improve bond strength.Laser application had no influence in improving the bond strength between the indirect composite and resin cement.

  18. Thermal Cyclic Resistance Polyester Resin Composites Reinforce Fiber Nut Shell

    Science.gov (United States)

    Fahmi, Hendriwan

    2017-12-01

    The purpose of study is to determine the effect of fiber length and thermal cyclic of the bending strength of polyester resin composite reinforced by fibers nut shell. The materials used in this study is a nut shell fibers with fiber length of 1 cm, 2 cm and 3 cm and polyester resin with composition 70-30%wt. Fiber nut shell treated soaking in NaOH 30% for 30 minutes, then rinse with clean water so that the fiber free of alkali and then dried. Furthermore, the composite is heated in an oven to a temperature of 100°C for 1 hour and then cooled in the open with a variety of thermal cyclic 30, 40, and 50 times. Bending properties of composites known through the testing process using a three-point bending test equipment universal testing machine. The test results show that the bending strength bending highest in fiber length of 3 cm with 30 treatment cycles of thermal to the value of 53.325 MPa, while the lowest occurred in bending strength fiber length of 1 cm with no cycles of thermal treatment to the value of 30.675 MPa.

  19. Polishing and toothbrushing alters the surface roughness and gloss of composite resins.

    Science.gov (United States)

    Kamonkhantikul, Krid; Arksornnukit, Mansuang; Takahashi, Hidekazu; Kanehira, Masafumi; Finger, Werner J

    2014-01-01

    This study aimed to investigate the surface roughness and gloss of composite resins after using two polishing systems and toothbrushing. Six composite resins (Durafill VS, Filtek Z250, Filtek Z350 XT, Kalore, Venus Diamond, and Venus Pearl) were evaluated after polishing with two polishing systems (Sof-Lex, Venus Supra) and after toothbrushing up to 40,000 cycles. Surface roughness (Ra) and gloss were determined for each composite resin group (n=6) after silicon carbide paper grinding, polishing, and toothbrushing. Two-way ANOVA indicated significant differences in both Ra and gloss between measuring stages for the composite resins tested, except Venus Pearl, which showed significant differences only in gloss. After polishing, the Filtek Z350 XT, Kalore, and Venus Diamond showed significant increases in Ra, while all composite resin groups except the Filtek Z350 XT and Durafill VS with Sof-Lex showed increases in gloss. After toothbrushing, all composite resin demonstrated increases in Ra and decreases in gloss.

  20. Microtensile bond strength of indirect resin composite to resin-coated dentin: interaction between diamond bur roughness and coating material.

    Science.gov (United States)

    Kameyama, Atsushi; Oishi, Takumi; Sugawara, Toyotarou; Hirai, Yoshito

    2009-02-01

    This aim of this study was to determine the effect of type of bur and resin-coating material on microtensile bond strength (microTBS) of indirect composite to dentin. Dentin surfaces were first ground with two types of diamond bur and resin-coated using UniFil Bond (UB) or Adper Single Bond (SB), and then bonded to a resin composite disc for indirect restoration with adhesive resin cement. After storage for 24 hr in distilled water at 37 degrees C, microTBS was measured (crosshead speed 1 mm/min). When UB was applied to dentin prepared using the regular-grit diamond bur, microTBS was significantly lower than that in dentin prepared using the superfine-grit bur. In contrast, no significant difference was found between regular-grit and superfine-grit bur with SB. However, more than half of the superfine-grit specimens failed before microTBS testing. These results indicate that selection of bur type is important in improving the bond strength of adhesive resin cement between indirect resin composite and resin-coated dentin.

  1. Incorporation of antibacterial agent derived deep eutectic solvent into an active dental composite.

    Science.gov (United States)

    Wang, Jing; Dong, Xiaoqing; Yu, Qingsong; Baker, Sheila N; Li, Hao; Larm, Nathaniel E; Baker, Gary A; Chen, Liang; Tan, Jingwen; Chen, Meng

    2017-12-01

    To incorporate an antibacterial agent derived deep eutectic solvent (DES) into a dental resin composite, and investigate the resulting mechanical properties and antibacterial effects. The DES was derived from benzalkonium chloride (BC) and acrylic acid (AA) and was incorporated into the dental resin composite through rapid mixing. A three-point bending test was employed to measure the flexural strength of the composite. An agar diffusion test was used to investigate antibacterial activity. Artificial (accelerated) aging was undertaken by immersing the composites in buffer solutions at an elevated temperature for up to 4 weeks. UV-vis spectrophotometry and NMR analysis were conducted to study BC release from the composite. Finally, the biocompatibility of the composite materials was evaluated using osteoblast cell culture for 7 days. Results were compared to those of a control composite which contained no BC. The DES-incorporated composite (DES-C) displayed higher flexural strength than a similar BC-incorporated composite BC (BC-C) for the same level of BC. The inclusion of BC conferred antibacterial activity to both BC-containing composites, although BC-C produced larger inhibition halos than DES-C at the same loading of BC. Control composites which contained no BC showed negligible antibacterial activity. After artificial aging, the DES-C composite showed better maintenance of the mechanical properties of the control compared with BC-C, although a decrease was observed during the three-point bending test, particularly upon storage at elevated temperatures. No BC release was detected in the aged solutions of DES-C, whereas the BC-C showed a linear increase in BC release with storage time. Significantly, cell viability results indicated that DES-C has better biocompatibility than BC-C. The incorporation of a BC-based DES into a dental resin composite provides a new strategy to develop antibacterial dental materials with better biocompatibility and longer effective

  2. Retention of cast crowns cemented to amalgam and composite resin cores.

    Science.gov (United States)

    Hormati, A A; Denehy, G E

    1981-05-01

    An in vitro study was conducted to determine the tensile bond strength of complete cast gold restorations cemented with zinc phosphate cement on composite resin and amalgam crown cores. The samples were thermocycled and tested at 1-week, 1-month, and 3-month intervals. Results of the study showed that: (1) the amalgam core provides more retention for the cast gold crown than does the composite resin core and (2) the composite resin core provides increasing retention over a longer time period.

  3. Diametral tensile strength of four composite resin core materials with and without centered fiber dowels.

    Science.gov (United States)

    Driessen, Cornel H; Ji, Donatta Y-J; Rizkalla, Amin S; Santos, Gildo C

    2011-01-01

    This study evaluated the diametral tensile strength of composite resin core materials with and without fiber dowels. Eight groups were established (n = 20), four with composite resins and four with fiber dowels. Samples were tested using a universal testing machine and evaluated using scanning electron microscopy. One-way ANOVA and a Tukey B-rank order test (P = 0.05) indicated that the tensile values of two of the four composite resins decreased significantly when their matching fiber dowels were introduced.

  4. Diffusion through composite materials made with thermosetting resins

    International Nuclear Information System (INIS)

    Morin, Bruno.

    1981-08-01

    Medium and low-level radioactive wastes may be coated in a solid matrix mainly made with thermosetting resins: the study of water and cesium migration through composite materials made with thermosetting resins is usefull to compare the water tightness of different coatings. Disks with a thickness of two millimeters were used to measure the water absorption. Diffusion cells including a plane membrane the thickness of which was at least 70μ were used to measure the diffusion of cesium 137. The diffusion coefficient of water in pure thermosetting resins, polyester or epoxyde, is about 10 -9 cm 2 .s -1 ; the diffusion coefficients of cesium in the same materials are about 10 -12 cm 2 .s -1 ; the introduction of solid particles in these polymers generally induces an acceleration of the diffusion process: the diffusion coefficient may reach 10 -8 cm 2 .s -1 . This lost of water-tightness may be reduced either by rendering insoluble the filler mixed to the polymer, or by diminushing the porosity of the interfacial zones by improving the bonding between the polymer and the filler [fr

  5. Epoxy Resin Composite Based on Functional Hybrid Fillers.

    Science.gov (United States)

    Oleksy, Mariusz; Szwarc-Rzepka, Karolina; Heneczkowski, Maciej; Oliwa, Rafał; Jesionowski, Teofil

    2014-08-22

    A study was carried out involving the filling of epoxy resin (EP) with bentonites and silica modified with polyhedral oligomeric silsesquioxane (POSS). The method of homogenization and the type of filler affect the functional and canceling properties of the composites was determined. The filler content ranged from 1.5% to 4.5% by mass. The basic mechanical properties of the hybrid composites were found to improve, and, in particular, there was an increase in tensile strength by 44%, and in Charpy impact strength by 93%. The developed hybrid composites had characteristics typical of polymer nanocomposites modified by clays, with a fine plate morphology of brittle fractures observed by SEM, absence of a plate separation peak in Wide Angles X-ray Scattering (WAXS) curves, and an exfoliated structure observed by TEM.

  6. Epoxy Resin Composite Based on Functional Hybrid Fillers

    Directory of Open Access Journals (Sweden)

    Mariusz Oleksy

    2014-08-01

    Full Text Available A study was carried out involving the filling of epoxy resin (EP with bentonites and silica modified with polyhedral oligomeric silsesquioxane (POSS. The method of homogenization and the type of filler affect the functional and canceling properties of the composites was determined. The filler content ranged from 1.5% to 4.5% by mass. The basic mechanical properties of the hybrid composites were found to improve, and, in particular, there was an increase in tensile strength by 44%, and in Charpy impact strength by 93%. The developed hybrid composites had characteristics typical of polymer nanocomposites modified by clays, with a fine plate morphology of brittle fractures observed by SEM, absence of a plate separation peak in Wide Angles X-ray Scattering (WAXS curves, and an exfoliated structure observed by TEM.

  7. Volumetric dimensional changes of dental light-cured dimethacrylate resins after sorption of water or ethanol.

    Science.gov (United States)

    Sideridou, Irini D; Karabela, Maria M; Vouvoudi, Evagelia Ch

    2008-08-01

    This study evaluated the influence of water and ethanol sorption on the volumetric dimensional changes of resins prepared by light curing of Bis-GMA, Bis-EMA, UDMA, TEGDMA or D(3)MA. The resin specimens (15mm diameterx1mm height) were immersed in water or ethanol 37+/-1 degrees C for 30 days. Volumetric changes of specimens were obtained via accurate mass measurements using Archimedes principle. The specimens were reconditioned by dry storage in an oven at 37+/-1 degrees C until constant mass was obtained and then immersed in water or ethanol for 30 days. The volumetric changes of specimens were determined and compared to those obtained from the first sorption. Resins showed similar volume increase during the first and second sorptions of water or ethanol. The volume increase due to water absorption is in the following order: poly-TEGDMA>poly-Bis-GMA>poly-UDMA>poly-Bis-EMA>poly-D(3)MA. On the contrary, the order in ethanol is poly-Bis-GMA>poly-UDMA>poly-TEGDMA>poly-Bis-EMA approximately poly-D(3)MA. The volume increase was found to depend linearly on the amount of water or ethanol absorbed. In the choice of monomers for preparation of composite resin matrix the volume increase in the resin after immersion in water or ethanol must be taken into account. Resins of Bis-EMA and D(3)MA showed the lowest values.

  8. Epoxy resin/carbon black composites below the percolation threshold.

    Science.gov (United States)

    Macutkevic, J; Kuzhir, P; Paddubskaya, A; Maksimenko, S; Banys, J; Celzard, A; Fierro, V; Stefanutti, E; Cataldo, A; Micciulla, F; Bellucci, S

    2013-08-01

    A set of epoxy resin composites filled with 0.25-2.0 wt.% of commercially available ENSACO carbon black (CB) of high and low surface area (CBH and CBL respectively) has been produced. The results of broadband dielectric spectroscopy of manufactured CB/epoxy below the percolation threshold in broad temperature (200 K to 450 K) and frequency (20 Hz to 1 MHz) ranges are reported. The dielectric properties of composites below the percolation threshold are mostly determined by alpha relaxation in pure polymer matrix. The glass transition temperature for CB/epoxy decreases in comparison with neat epoxy resin due to the extra free volume at the polymer-filler interface. At room temperature, the dielectric permittivity is higher for epoxy loaded with CBH additives. In contrast, at high temperature, the electrical conductivity was found to be higher for composites with CBL embedded. The established influence of the CB surface area on the broadband dielectric characteristics can be exploited for the production of effective low-cost antistatic paints and coatings working at different temperatures.

  9. Mechanical properties of composite resin blocks for CAD/CAM.

    Science.gov (United States)

    Lauvahutanon, Sasipin; Takahashi, Hidekazu; Shiozawa, Maho; Iwasaki, Naohiko; Asakawa, Yuya; Oki, Meiko; Finger, Werner J; Arksornnukit, Mansuang

    2014-01-01

    This study compared commercial composite resin blocks with one ceramic block for use in computer-aided design/computer aided manufacturing (CAD/CAM). Four composite resins, one composite ceramic, and one feldspar-ceramic block were investigated. Flexural strength (FS), flexural modulus (FM), and Vickers hardness (VH) were determined under three conditions: dry storage; immersion in water at 37°C for 7 days; and immersion in water at 37°C for 7 days followed by 10,000 thermocycles. After dry storage, FS ranged from 127 to 242 MPa, FM from 9.6 to 51.5 GPa, and VH from 64 to 455. Two-way ANOVA was performed for FS, FM and VH followed by Tukey's multiple comparison (α<0.05). Results demonstrated that the materials degraded after water immersion and thermocycling, but their properties were within the acceptable range for fabrication of single restorations according to the ISO standard for ceramics (ISO 6872:2008).

  10. Surface roughness comparison of methacrylate and silorane-based composite resins after 40% hydrogen peroxide application

    Directory of Open Access Journals (Sweden)

    Rori Sasmita

    2018-01-01

    Full Text Available The change of the tooth colour could be restored with bleaching. The tooth bleaching will affects the surface roughness of the composite resins. Recently, the material basis for composite resins has developed, among others are methacrylate-based and silorane based composite resins. The objective of this study was to distinguish the surface roughness value of methacrylate-based composite resin and silorane based composite resins. This research was quasi-experimental. The sample used in this study were methacrylate and silorane based composite resins in discs form, with the size of 6 mm and the thickness of 3 mm, manufactured into 20 specimens and divided into 2 groups. The control group was immersed in the artificial saliva, and the treatment group was applied with 40% hydrogen peroxide. The result of the experiment analyzed using unpaired sample t-test showed significant differences in the average value of the surface roughness after the application of 40% hydrogen peroxide. The average value of methacrylate and silorane based composite resins were 2.744 μm and 3.417 μm, respectively. There was a difference in the surface roughness of methacrylate and silorane based composite resin compounds after the application of 40% hydrogen peroxide. The surface roughness value of the silorane-based composite resin was higher than the methacrylate-based.

  11. Characteristics of low polymerization shrinkage flowable resin composites in newly-developed cavity base materials for bulk filling technique.

    Science.gov (United States)

    Nitta, Keiko; Nomoto, Rie; Tsubota, Yuji; Tsuchikawa, Masuji; Hayakawa, Tohru

    2017-11-29

    The purpose of this study was to evaluate polymerization shrinkage and other physical properties of newly-developed cavity base materials for bulk filling technique, with the brand name BULK BASE (BBS). Polymerization shrinkage was measured according to ISO/FDIS 17304. BBS showed the significantly lowest polymerization shrinkage and significantly higher depth of cure than conventional flowable resin composites (p<0.05). The Knoop hardness, flexural strength and elastic modulus of that were significantly lower than conventional flowable resin composites (p<0.05). BBS had the significantly greatest filler content (p<0.05). SEM images of the surface showed failure of fillers. The lowest polymerization shrinkage was due to the incorporation of a new type of low shrinkage monomer, which has urethane moieties. There were no clear correlations between inorganic filler contents and polymerization shrinkage, flexural strength and elastic modulus. In conclusion, the low polymerization shrinkage of BBS will be useful for cavity treatment in dental clinics.

  12. Determination of ablation threshold for composite resins and amalgam irradiated with femtosecond laser pulses

    Science.gov (United States)

    Freitas, A. Z.; Freschi, L. R.; Samad, R. E.; Zezell, D. M.; Gouw-Soares, S. C.; Vieira, N. D., Jr.

    2010-03-01

    The use of laser for caries removal and cavity preparation is already a reality in the dental clinic. The objective of the present study was to consider the viability of ultrashort laser pulses for restorative material selective removal, by determining the ablation threshold fluence for composite resins and amalgam irradiated with femtosecond laser pulses. Lasers pulses centered at 830 nm with 50 fs of duration and 1 kHz of repetition rate, with energies in the range of 300 to 770 μJ were used to irradiate the samples. The samples were irradiated using two different geometrical methods for ablation threshold fluence determinations and the volume ablation was measured by optical coherence tomography. The shape of the ablated surfaces were analyzed by optical microscopy and scanning electron microscopy. The determined ablation threshold fluence is 0.35 J/cm2 for the composite resins Z-100 and Z-350, and 0.25 J/cm2 for the amalgam. These values are half of the value for enamel in this temporal regime. Thermal damages were not observed in the samples. Using the OCT technique (optical coherence tomography) was possible to determine the ablated volume and the total mass removed.

  13. Fatigue resistance and failure mode of adhesively restored custom metal-composite resin premolar implant abutments.

    Science.gov (United States)

    Boff, Luís Leonildo; Oderich, Elisa; Cardoso, Antônio Carlos; Magne, Pascal

    2014-01-01

    To evaluate the fatigue resistance and failure mode of composite resin and porcelain onlays and crowns bonded to premolar custom metal-composite resin premolar implant abutments. Sixty composite resin mesostructures were fabricated with computer assistance with two preparation designs (crown vs onlay) and bonded to a metal implant abutment. Following insertion into an implant with a tapered abutment interface (Titamax CM), each metal-composite resin abutment was restored with either composite resin (Paradigm MZ100) or ceramic (Paradigm C) (n = 15) and attached with adhesive resin (Optibond FL) and a preheated light-curing composite resin (Filtek Z100). Cyclic isometric chewing (5 Hz) was then simulated, starting with 5,000 cycles at a load of 50 N, followed by stages of 200, 400, 600, 800, 1,000, 1,200, and 1,400 N (25,000 cycles each). Samples were loaded until fracture or to a maximum of 180,000 cycles. The four groups were compared using life table survival analysis (log-rank test). Previously published data using zirconia abutments of the same design were included for comparison. Paradigm C and MZ100 specimens fractured at average loads of 1,133 N and 1,266 N, respectively. Survival rates ranged from 20% to 33.3% (ceramic crowns and onlays) to 60% (composite resin crowns and onlays) and were significantly different (pooled data for restorative material). There were no restoration failures, but there were adhesive failures at the connection between the abutment and the mesostructure. The survival of the metal-composite resin premolar abutments was inferior to that of identical zirconia abutments from a previous study (pooled data for abutment material). Composite resin onlays/crowns bonded to metal-composite resin premolar implant abutments presented higher survival rates than comparable ceramic onlays/crowns. Zirconia abutments outperformed the metal-composite resin premolar abutments.

  14. Hardness Evaluation of Composite Resins Cured with QTH and LED

    Directory of Open Access Journals (Sweden)

    Behnaz Esmaeili

    2014-03-01

    Full Text Available Background and aims. Today light cured composites are widely used. Physical and mechanical properties of composites are related to the degree of conversion. Light curing unit (LCU is an important factor for composite polymerization. Aim of this study is evaluation of composite resins hardness using halogen and LED light curing units. Materials and methods. In this study, 30 samples of Filtek Z250 and C-Fill composite resins were provided. Samples were light cured with Ultralume2, Valo and Astralis7. Vickers hardness number (VHN was measured in 0, 1, 2 mm depth. Statistical analysis used: Data were analysed by SPSS software and compared with each other by T-test, one-way and twoway ANOVA and Post-hoc Tukey test. Results. In Filtek Z250, at top surface, VHN of Ultralume2 was higher than VHN of Valo (P = 0.02 and Astralis7 (P = 0.04, but in depth of 1, 2 mm, VHN of Ultralume2 and Astralis7 were almost the same and both LCUs were more than Valo which the difference between Ultralume2 and Valo was significant in depth of 1mm (0.05 and 2mm (0.02. In C-Fill composite, at top surface, Astralis7 showed higher VHN, but in depth of 2 mm, performance of all devices were rather similar. Conclusion. In Z250, which contains camphorquinone initiator, light cure LED Ultra-lume2 with narrow wavelength showed higher hardness number than Valo. In C-fill, in top surface, Astralis7 with more exposure time, resulted higher VHN. But In depth of 2 mm, various light curing devices had rather similar hardness number.

  15. Penggunaan Fiber Reinforced Composite Sebagai Resin Bonded Prosthesis Pada Gigi Anterior

    OpenAIRE

    Pintadi, Hastoro

    2007-01-01

    Resin bonded prosthesis is a fixed bridge which replace a space where one or two teeth have been lost or extracted, by using acid etched technique and resin bonding. The main goals in selecting a Resin bonded prosthesis were to preserve tooth structure, maintain esthetics and lower patient fees while providing restorations that had the potential for long-term service. This case report discuss about fiber reinforced composite used as a main material for resin bondedprosthesis to replace incivu...

  16. Selecting the Best Materials Compositions of Resin Based Bioasphalt

    Science.gov (United States)

    Setyawan, Ary; Widiharjo, Budi; Djumari

    2017-07-01

    Damar asphalt is one type of bioaspal which is a mixture with the main ingredient is a resin as a binder and cooking oil as a solvent. One major drawback of this damar asphalt is the low ductility. To improve the ductility values, then use the added material Filler. Filler serves as a divider between the impurities with damar asphalt, increases ductility and increase the ability of cohesion or bonding between the particles of material damar asphalt. The purpose of this study was to determine damar asphalt modifications to the properties in accordance with the properties of damar asphalt test specifications based on the value of penetration. This method uses some variant on material such as powder bricks and fly ash as a binder. Solvent in constituent used oil and used cooking oil. It also added the polymer latex up to 10% at intervals of 2%. The best composition of damar asphalt materials were obtained with gum rosin, Fly Ash, Oil and Latex. Damar asphalt modification damar asphalt optimum mix of resin (100g pure resin or resin chunk + 350g powder), Fly Ash powder (150g), cooking oil (205g), and latex 4%, ductility increased from 63.5 cm to 119.5 cm, the value of the flash point was originally at temperature of 240 °C to 260 °C, damar asphalt penetration of 68.2 dmm to 43 dmm, and the value of density decreases from 1.01 g / cm3 to 0.99 g / cm3. Damar asphalt at these modifications meet the specifications in terms of solubility in trichlore ethylene is equal to 99.5%, and also meet the affinity of damar asphalt at 99%. With the optimum value, damar asphalt could be categorized as bitumen 40/60 penetration.

  17. Utilization of iTero digital impression unit for resin composite inlay.

    Science.gov (United States)

    Laman, Stephen A; Frey, Gary N; Patel, Shalizeh A; Quock, Ryan L

    2014-01-01

    Historically, traditional elastomeric impression techniques for indirect fixed procedures have presented challenges for the operator, laboratory, and patient. Recent digital impression unit technology offers a compelling alternative to elastomeric impressions. The iTero system applies parallel confocal imaging to create a virtual impression that can be easily captured, edited, and uploaded electronically to the dental laboratory. Computer-aided design/computer-aided manufacturing technology is applied to the virtual impression to create an unlimited number of identical polyurethane models. This case report is presented from the perspectives of the clinicians and the laboratory technician using an iTero system to treat a left mandibular second premolar with a resin composite inlay.

  18. Stain susceptibility of composite and ceramic CAD/CAM blocks versus direct resin composites with different resinous matrices.

    Science.gov (United States)

    Alharbi, Amal; Ardu, Stefano; Bortolotto, Tissiana; Krejci, Ivo

    2017-04-01

    To evaluate the stain susceptibility of CAD/CAM blocks and direct composite after long term exposure to various staining agents. 40 disk-shaped samples were fabricated from each of nine materials; six CAD/CAM (Vitablocs Mark II, Paradigm MZ100, Experimental Vita Hybrid Ceramic, Vita Enamic, Experimental Kerr and Lava Ultimate) and three direct composites (Filtek Supreme, Venus Diamond and Filtek Silorane). Samples were randomly divided into five groups (n = 8) according to different staining solutions (distilled water, tea, red wine, coffee and artificial saliva). Initial L*a*b* values were assessed using a calibrated digital spectrophotometer. Specimens were immersed in staining solutions and stored in an incubator at 37 °C for 120 days. L*a*b* values were assessed again and color change (∆E) was calculated as difference between recorded L*a*b* values. ANOVA, and Duncan test were used to identify differences between groups (α = 0.05). Significant differences in ∆E values were detected between materials (p = 0.000). Among all staining solutions, the highest ∆E value was observed with red wine. The new CAD/CAM blocks (Vita Enamic, Vita Hybrid Ceramic and Lava Ultimate) showed the highest resistance to staining compared to the MZ100 composite resin blocks. Filtek Silorane, a direct composite, showed high stain resistance values compared to CAD/CAM materials and other direct composites. Ceramic and composite CAD/CAM blocks had lower staining susceptibility than methacrylate based direct composite. Staining susceptibility of the new resin based CAD/CAM materials Vita Enamic and Lava Ultimate was comparable to feldspathic ceramic blocks (Vitablocs Mark II). Filtek Silorane showed promising results that were comparable to some CAD/CAM blocks.

  19. Effects of resin content and preparing conditions on the properties of polyphenylene sulfide resin/graphite composite for bipolar plate

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Li-gang; Li, Ai-ju; Yin, Qiang [Key Laboratory for Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Shandong Key Laboratory of Engineering Ceramics, Shandong University, Jinan 250061 (China); Wang, Wei-qiang [School of Mechanical Engineering, Shandong University, Jinan 250061 (China); Lin, Heng; Zhao, Yi-bo [School of Material Science and Engineering, Shandong University, Jinan 250061 (China)

    2008-03-15

    In the paper, a kind of polyphenylene sulfide (PPS) resin/graphite (G) composite for bipolar plate was prepared by using the PPS resin as adhesive and simple hot pressing. The influences of the resin content, the molding temperature and holding time on the conductivity and the bending strength of the PPS/G composite bipolar plate were investigated firstly and then the optimum content and the preparing conditions of the composite were obtained. The experimental results show that the electrical conductivity decreases and the bending strength reveals a serrated variation with increase in PPS resin content; when the holding time is certain, the conductivity decreases and the bending strength increases with the molding temperature increasing. The experimental results further show that the effect of the holding time on the properties of the composite is different at different molding temperatures. The PPS/G composite with 20% PPS resin content has electrical conductivity of 118.9 S cm{sup -1} and bending strength of 52.4 MPa when it molded at 380 C for 30 min, and has electrical conductivity of 105 S cm{sup -1}, bending strength of 55.7 MPa when it molded at 390 C for 30 min. The properties of the composites can meet the requirements of United States Department of Energy (DOE). (author)

  20. Protein-repellent and antibacterial dental composite to inhibit biofilms and caries.

    Science.gov (United States)

    Zhang, Ning; Ma, Jianfeng; Melo, Mary A S; Weir, Michael D; Bai, Yuxing; Xu, Hockin H K

    2015-02-01

    Biofilm acids contribute to secondary caries, which is a main reason for dental restoration failures. The objectives of this study were to: (1) develop a protein-repellent and antibacterial composite, and (2) investigate the effects of combining 2-methacryloyloxyethyl phosphorylcholine (MPC) with quaternary ammonium dimethylaminohexadecyl methacrylate (DMAHDM) on composite mechanical properties and biofilm response for the first time. MPC, DMAHDM and glass particles were mixed into a dental resin composite. Mechanical properties were measured in three-point flexure. Protein adsorption onto the composites was measured by a micro bicinchoninic acid method. A human saliva microcosm model was used to grow biofilms on composites. Colony-forming unit (CFU) counts, live/dead assay, metabolic activity, and lactic acid production of biofilms were determined. Incorporation of 3% MPC and 1.5% DMAHDM into composite achieved protein-repellent and antibacterial capabilities without compromising the mechanical properties. Composite with 3% MPC+1.5% DMAHDM had protein adsorption that was 1/10 that of a commercial composite (pbiofilm growth than using MPC or DMAHDM alone (pBiofilm CFU counts on composite with 3% MPC+1.5% DMAHDM were more than three orders of magnitude lower than that of commercial control. Dental composite with a combination of strong protein-repellent and antibacterial capabilities was developed for the first time. Composite containing MPC and DMAHDM greatly reduced biofilm growth and lactic acid production, without compromising mechanical properties of the composite. Novel composite with MPC and DMAHDM greatly reduced biofilm activity and is promising to inhibit secondary caries. The dual agents of MPC plus DMAHDM may have wide applicability to other dental materials. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Effectiveness of bleaching agent on composite resin discoloration

    Directory of Open Access Journals (Sweden)

    Galih Sampoerno

    2012-03-01

    Full Text Available Background: The discoloration of teeth, especially anterior teeth, is one of aesthetic problems. The use of tooth bleaching agents for discolored natural teeth is becoming increasingly popular. Many dentists, however, get many problems when they conduct bleaching process since there is much composite filling on patient’s anterior teeth. Although many research have focused on the discoloration of composite resin after bleaching process, the problem still becomes debatable. Purpose: The purpose of this study was to investigate the difference of the discoloration between hybrid composite and nano composite before and after the application of tooth bleaching agent, 38% hydrogen peroxide. Methods: Eighteen disk-shaped specimens (5 mm of each of two composite resins, hybrid and nano filler, were prepared. The each group was treated 3 times and the specimens were divided into two groups consisted of 9 specimens for each, and then immersed in black tea solutions for 72 hours. Next, after having staining and bleaching processes, the color of the specimens was measured with a optic spectrophotometer by using photo with type BPY-47 and digital microvolt. The differences of the light intensity among three measurements were then calculated. Afterwards, GLM MANOVA Repeated Measure and parametric analysis (Independent t-test and Paired t-test were then used to analyze the data. Results: After staining process, it is then known that the nano composite had more discoloration and more affected by the black tea solution than the hybrid one. Conclusion: After bleaching, the discoloration was finally removed completely from both hybride and nano filler composite resins and became brighter from the baseline color.Latar belakang: Salah satu problem estetik adalah adanya perubahan warna pada gigi anterior. Peningkatan pemakaian bahan bleaching semakin popular. Banyak dokter gigi mempunyai problem ketika mereka akan melakukan proses bleaching dan ditemukan banyak

  2. Mechanical behaviour of dental composite filling materials using digital holography

    OpenAIRE

    Monteiro, J.M.; Lopes, H.; Vaz, M.A.P.; Campos, J.C. Reis

    2010-01-01

    One of the most common clinical problems in dentistry is tooth decay. Among the dental filling materials used to repair tooth structure that has been destroyed by decay are dental amalgam and composite materials based on acrylics. Dental amalgam has been used by dentists for the past 150 years as a dental restorative material due to its low cost, ease of application, strength, durability, and bacteriostatic effects. However its safety as a filling material has been questioned due to th...

  3. Young's modulus and degree of conversion of different combination of light-cure dental resins.

    Science.gov (United States)

    Emami, N; Söderholm, Kj

    2009-10-01

    To evaluate Young's modulus and degree of conversion of several combinations of bisGMA, UEDMA, TEGDMA light-cure dental resin. Young's modulus and DC% were studied for 21 different resin combinations of bisGMA, TEGDMA and UEDMA. Small universal testing machine and photo-calorimetry were used for the tests. The results were evaluated using ANOVA and Duncan's multiple range tests and regular t-test. Young's modulus varied between 2.37±0.2 GPa (100% TEGDMA) and 4.15±0.2 GPa (100% bisGMA). By adding TEGDMA to bisGMA or UEDMA, the Young's modulus decreased significantly (pphysical properties of the mixtures.

  4. Effect of sealant agents on the color stability and surface roughness of nanohybrid composite resins.

    Science.gov (United States)

    Dede, Doğu Ömür; Şahin, Onur; Koroglu, Aysegül; Yilmaz, Burak

    2016-07-01

    The effect of sealant agents on the surface roughness and color stability of nanohybrid composite resins is unknown. The purpose of this in vitro study was to evaluate the effect of sealant agents on the surface roughness and color stability of 4 nanohybrid composite resin materials. Forty disks (10×2 mm) were fabricated for each nanohybrid composite resin material (Z-550, Tetric EvoCeram, Clearfill Majesty, Ice) (N=160) and divided into 4 surface treatment groups: 1 conventional polishing (control) and 3 different sealant agent (Palaseal, Optiglaze, BisCover) coupling groups (n=10). The specimens were thermocycled, and surface roughness (Ra) values were obtained with a profilometer. Scanning electron microscope images were also recorded. CIELab color parameters of each specimen were measured with a spectrophotometer before and after 7 days of storage in a coffee solution. Color differences were calculated by the CIEDE 2000 (ΔE00) formula. The data were statistically analyzed by 2-way ANOVA and by the Tukey HSD test (α=.05). The surface treatment technique significantly affected the Ra values of the composite resins tested (Pcomposite resin material was also significant for ΔE00 values (Pcomposite resin groups, significant decreases in Ra were observed only for the Palaseal agent coupled composite resin groups (except Ice) compared with the control groups (Pcomposite resin group, except for BisCover applied Clearfill Majesty (Pcomposite resin groups, significant differences were observed between the color change seen with BisCover and other sealants for Clearfill Majesty composite resin (Pcomposite resins except for Ice produced smoother surfaces. All surface sealant agents provided less discoloration of nanohybrid composite resins after coffee staining compared with conventional polishing except for BisCover applied Clearfill Majesty composite resin. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All

  5. Process for hardening an alkyd resin composition using ionizing radiation

    International Nuclear Information System (INIS)

    Watanabe, Tadashi; Murata, Koichiro; Maruyama, Tsutomu.

    1969-01-01

    In an alkyd resin composition having free hydroxide radicals and containing a conjugated unsaturated fatty acid and/or oil as a component thereof, a process for hardening an alkyd resin composition comprises the steps of dissolving into a vinyl monomer, the product obtained by the semi-esterification reaction of said hydroxide radicals with acid anhydrides having polymerizable radicals and hardening by ionizing radiation to provide a coating with a high degree of cross-linking, with favorable properties such as toughness, hardness, chemical resistance and resistance to weather and with the feasibility of being applied as the ground and finish coat on metals, wood, paper, outdoor construction or the like. Any kind of ionization radiation, particularly accelerated electron beams, γ radiation can be used at 50 0 C to -5 0 C for a few seconds or minutes, permitting continuous operation. In one example, 384 parts of phthalic anhydride, 115 parts of pentaerythritol, 233 parts of trimethylol ethane, 288 parts of tung fatty acid and 49 parts of para-tertiary-butyl benzoic acid are mixed and heated with 60 parts of xylene to an acid value of 12. In addition, 271 parts of maleic anhydride and 0.6 parts of hydroquinone are admixed with the content and heated to terminate the reaction. 100 parts of a 50% stylene solution of this alkyd resin are mixed with 1 part of a 60% toluene solution of cobalt naphthenate, and then coated on a glass plate and irradiated with high energy electron beams of 300 kV with a dose of 5 Mrad for 1 sec. (Iwakiri, K.)

  6. Epoxy Resin Based Composites, Mechanical and Tribological Properties: A Review

    Directory of Open Access Journals (Sweden)

    S.A. Bello

    2015-12-01

    Full Text Available High fuel consumption by automobile and aerospace vehicles built from legacy alloys has been a great challenge to global design and material engineers. This has called for researches into material development for the production of lighter materials of the same or even superior mechanical properties to the existing materials in this area of applications. This forms a part of efforts to achieve the global vision 2025 i.e to reduce the fuel consumption by automobile and aerospace vehicles by at least 75 %. Many researchers have identified advanced composites as suitable materials in this regard. Among the common matrices used for the development of advanced composites, epoxy resin has attained a dominance among its counterparts because of its excellent properties including chemical, thermal and electrical resistance properties, mechanical properties and dimensional stability. This review is a reflection of the extensive study on the currently ongoing research aimed at development of epoxy resin hybrid nanocomposites for engineering applications. In this paper, brief explanation has been given to different terms related to the research work and also, some previous works (in accordance with materials within authors’ reach in the area of the ongoing research have been reported.

  7. Nano-sized aerosol classification, collection and analysis--method development using dental composite materials.

    Science.gov (United States)

    Bogdan, Axel; Buckett, Mary I; Japuntich, Daniel A

    2014-01-01

    This article presents a methodical approach for generating, collecting, and analyzing nano-size (1-100 nm) aerosol from abraded dental composite materials. Existing aerosol sampling instruments were combined with a custom-made sampling chamber to create and sample a fresh, steady-state aerosol size distribution before significant Brownian coagulation. Morphological, size, and compositional information was obtained by Transmission Electron Microscopy (TEM). To create samples sizes suitable for TEM analysis, aerosol concentrations in the test chamber had to be much higher than one would typically expect in a dental office, and therefore, these results do not represent patient or dental personnel exposures. Results show that nano-size aerosol was produced by the dental drill alone, with and without cooling water drip, prior to abrasion of dental composite. During abrasion, aerosol generation seemed independent of the percent filler load of the restorative material and the operator who generated the test aerosol. TEM investigation showed that "chunks" of filler and resin were generated in the nano-size range; however, free nano-size filler particles were not observed. The majority of observed particles consisted of oil droplets, ash, and graphitic structures.

  8. Resin composites: strength of the bond to dentin versus mechanical properties.

    Science.gov (United States)

    Thomsen, Kasper Boel; Peutzfeldt, Anne

    2007-03-01

    This study (1) investigated whether the combination of an adhesive system from one manufacturer with a resin composite from the same manufacturer provides superior bonding of the resin composite to dentin compared with the combination of an adhesive system from one manufacturer with a resin composite from another manufacturer, and (2) tested for a possible influence on bond strength of mechanical properties of the resin composite. After application of an adhesive system, a resin composite was bonded to flattened human dentin and tested in shear after 1 week. Five adhesive systems (AdheSE, Adper Prompt L-Pop, Clearfil SE Bond, Optibond Solo Plus, and Xeno III) were tested with each of five resin composites (Tetric Ceram, Filtek Supreme, Clearfil AP-X, Premise, and EsthetX). The mechanical properties flexural strength and flexural modulus were determined by three-point loading. Bond strengths were influenced by the brand of adhesive system (P resin composite (P resin composite from the same manufacturer did not provide bond strengths that were superior to those obtained when an adhesive system from one manufacturer was combined with a resin composite from another manufacturer. Independent of the brand of resin composite, the adhesive system Clearfil SE Bond mediated the highest bond strength to dentin. For each adhesive system, the resin composite Clearfil AP-X resulted in the highest bond strength to dentin. Significant positive correlations were found between bond strength and flexural strength (P < 0.0026, r = 0.21) and between bond strength and flexural modulus (P < 0.0017, r = 0.22).

  9. Marginal microleakage of resin-modified glass-ionomer and composite resin restorations: Effect of using etch-and-rinse and self-etch adhesives

    Directory of Open Access Journals (Sweden)

    Maryam Khoroushi

    2012-01-01

    Full Text Available Objectives: Previous studies have shown that dental adhesives increase the bond strength of resin-modified glass-ionomer (RMGI restorative materials to dentin. This in vitro study has evaluated the effect of etch-and-rinse and self-etch bonding systems v/s cavity conditioner, and in comparison to similar composite resin restorations on maintaining the marginal sealing of RMGI restorations. Materials and Methods: 98 rectangular cavities (2.5×3×1.5 mm were prepared on buccal and palatal aspects of 49 human maxillary premolars, randomly divided into 7 groups (N=14. The cavities in groups 1, 2 and 3 were restored using a composite resin (APX. The cavities in groups 4, 5, 6 and 7 were restored using a resin-modified glass-ionomer (Fuji II LC. Before restoring, adhesive systems (Optibond FL = OFL, three-step etch-and-rinse; One Step Plus = OSP, two-step etch-and-rinse; Clearfil Protect Bond = CPB, two-step self-etch were used as bonding agents in groups 1-6 as follow: OFL in groups 1 and 4, OSP in groups 2 and 5, and CPB in groups 3 and 6, respectively. The specimens in group 7 were restored with GC cavity conditioner and Fuji II LC. All the specimens were thermo-cycled for 1000 cycles. Microleakage scores were determined using dye penetration method. Statistical analyzes were carried out with Kruskal-Wallis and Mann-Whitney U tests (α=0.05. Results: There were significant differences in microleakage scores at both enamel and dentinal margins between the study groups (P<0.05. The lowest microleakage scores at enamel and dentin margins of RMGI restorations were observed in group 6. Conclusion: Use of two-step self-etch adhesive, prior to restoring cervical cavities with RMGIC, seems to be more efficacious than the conventional cavity conditioner in decreasing marginal microleakage.

  10. Marginal integrity of low-shrinkage and methacrylate-based composite resins: Effect of three different hemostatic agents

    Science.gov (United States)

    Khoroushi, Maryam; Sahraneshin-Samani, Mahsa

    2016-01-01

    Background Moisture control is very important in restorative procedures in dentistry. Use of hemostatic agents helps control moisture; however, they might result in changes on enamel and dentin surfaces, affecting composite resin bond quality. The aim of this in vitro study was to evaluate the marginal microleakage of two different composite resins with the use of three different hemostatic agents. Material and Methods Standardized Class V cavities were prepared on the buccal and lingual surfaces of 48 premolars with cervical margins 1 mm apical to the cementoenamel junction (CEJ). The samples were randomly divided into 8 groups. In groups 1 to 4, an etch-and-rinse adhesive (Adper Single Bond) was applied as the bonding system, followed by exposure to different hemostatic agent: group 1: no hemostatic agent (control); group 2: ViscoStat; group 3: ViscoStat Clear; and group 4: trichloracetic acid, as hemostatic agents. The cavities were restored with Z-250 composite resin. In group 5 to 8 Silorane System Adhesive (Filtek P90 Adhesive) was applied as a bonding agent, followed by exposure to different hemostatic agents in a manner similar to that in groups 1to 4. The cavities were restored with Filtek P90, a low-shrinkage composite resin. The samples in each group were evaluated for dye penetration under a stereomicroscope at ×36 after 24 hours and a 500-round thermocycling procedure at enamel and dentin margins. Statistical analysis was carried out using Kruskal-Wallis and Mann-Whitney tests (α=0.05). Results Z-250 composite resin exhibited significantly higher dentin microleakage scores compared to Filtek P90 (P = 0.004). Trichloracetic acid increased dentin microleakage with Filtek P90 (P=0.033). Conclusions Under the limitations of this in vitro study, application of hemostatic agents did not affect microleakage of the two tested composite resins except for trichloracetic acid that increased marginal microleakage when used with Filtek P90. Key words:Composite

  11. The effect of toothbrushing on surface gloss of resin composites.

    Science.gov (United States)

    Lefever, Dorien; Perakis, Nikolaos; Roig, Miguel; Krejci, Ivo; Ardu, Stefano

    2012-02-01

    To determine the changes in surface gloss of different composite materials after laboratory toothbrushing simulation. 36 specimens were fabricated for each material and polished with 120-, 220-, 500-, 1200-, 2400- and 4000-grit SiC abrasive paper, respectively. Gloss measurements were made with a glossmeter (Novocurve) prior to testing procedures and then subjected to simulated toothbrushing for 5, 15, 30 and 60 minutes by means of an electric toothbrush with a pressure of 2N while being immersed in a 50 RDA toothpaste slurry. Four supplementary samples per group were analyzed under SEM immediately after polishing procedures and four samples after 60 minutes simulated toothbrushing in order to evaluate the causes of the gloss decrease. The tested resin composite materials were Filtek Supreme XTE, Durafill, HRi Enamel Plus, Miris 2, Empress Direct, Venus Diamond, Gradia Direct, Clearfil Photo Posterior and G-aenial. Natural enamel represented the control group. Statistical analysis was performed using Kruskal Wallis and Tukey post-hoc test, with a level of significance set at 0.05. Resin composite initial gloss values ranged from 68.9 to 100.5 at baseline to 10.6 to 62.6 after 1 hour of brushing. Highest gloss values were obtained by Filtek Supreme XTE, followed by Empress Direct and Durafill. Lowest values were obtained by Clearfil Photoposterior, Miris 2, Enamel HRi and Venus Diamond. Natural enamel was the only substrate to maintain its gloss throughout the brushing procedure (110.4 after 60 minutes). SEM analysis revealed different patterns of surface degradation depending on the composite material.

  12. Characterization of Bis-Acryl Composite Resins for Provisional Restorations.

    Science.gov (United States)

    Schwantz, Júlia K; Oliveira-Ogliari, Aline; Meereis, Carine T; Leal, Fernanda B; Ogliari, Fabrício A; Moraes, Rafael R

    2017-01-01

    This study investigated the in vitro performance of the commercial bis-acryl composite resins Systemp C&B II (SYS, Ivoclar Vivadent), Protemp 4 (PT4, 3M ESPE), Structur 2C (ST2, Voco) and ProviPlast (PVP, Biodinamica). Characterization involved optical (color stability, translucency parameter, fluorescence), surface (roughness, morphology and elemental composition), physical-chemical (viscosity, polymerization kinetics) and mechanical analyses (Poisson ratio, biaxial flexural strength, flexural modulus). Most tests were carried out after 24 h, but optical and mechanical analyses were carried out after storage in water at 37 °C for 1, 15, and 30 days. Data were statistically analyzed (a=0.05). Most results were material dependent. SYS and PT4 showed stability in color and translucency over time. All materials had similar or higher fluorescence than human enamel. SC2 and PVP showed rougher surfaces than the other bis-acryl composites. Smaller filler particles were observed on the surface of PT4 and PVP compared with the coarser particles from ST2 and SYS. Viscosity readings indicated a thixotropic behavior for all tested materials. SYS had the lowest and PT4 the highest degree of C=C conversion after 10 min. In the polymerization kinetics, PT4 had the highest maximum polymerization rate and reached earlier the transition between polymerization autoacceleration and autodeceleration. PT4 and SYS had significantly higher flexural strength and modulus than ST2 and PVP for most storage times. Results for Poisson ratio varied between materials. Longer storage periods were generally associated with higher frequency of catastrophic failures in the flexural tests. In conclusion, the performance of bis-acryl composite resins varied largely among materials.

  13. Effect of TiO2 Nanoparticles on Tensile Strength of Dental Acrylic Resins.

    Science.gov (United States)

    Shirkavand, Saeed; Moslehifard, Elnaz

    2014-01-01

    Background and aims. Adding further fillers to dental resins may enhance their physical characteristics. The aim of this study was to evaluate the tensile strength of heat-curing acrylic resin reinforced by TiO2nanoparticles added into the resin matrix. Materials and methods. Commercially available TiO2 nanoparticles were obtained and characterized using X-ray diffrac-tion (XRD) and scanning electron microscopy (SEM) to determine their crystalline structure, particle size and morphology. TiO2-acrylic resin nanocomposite was prepared by mixing 0.5, 1 and 2 (wt%) of surface modified TiO2 nanoparticles in an amalgamator providing three groups of samples. Before curing, the obtained paste was packed into steel molds. After cur-ing, the specimens were removed from the molds. The tensile strength test samples were prepared according to ISO 1567. Results. Two crystalline phases were found in TiO2 nanoparticles including: (i) anatase as the major one, and (ii) rutile. The average particle size calculated according to the Scherrer equation was 20.4 nm, showing a normal size distribution. According to SEM images, the nanocomposite with 1wt% TiO2 nanoparticles had a better distribution compared to other groups. In addition, the group by 1wt% TiO2 exhibited higher tensile strength with a significant difference compared to other groups. ANOVA showed significant differences between the contents of TiO2 particles in acrylic resin (F = 22.19; P tensile strength was observed with titania NPs reinforcement agents in 1wt% by weight. Further increase of TiO2 nanoparticles decreased the tensile strength.

  14. Comparison of stabilities in translucency, fluorescence and opalescence of direct and indirect composite resins.

    Science.gov (United States)

    Yu, Bin; Lee, Young-Keun

    2013-01-01

    To evaluate translucency, fluorescence and opalescence stabilities of direct and indirect composite resins after aging. One direct (16 shades) and two indirect composite resins (16 and 26 shades) were investigated. Resins were filled in a mold (1 mm thick) and light cured; post-curings were performed for indirect resins. Color was measured before and after 5,000 cycles of thermocycling on a reflection spectrophotometer in reflectance and transmittance modes to calculate parameters for translucency (TP), fluorescence (FL) and opalescence (OP). Differences in the changes of TP, FL and OP after aging by the type of resin were determined by t test, and those were also determined by one-way ANOVA with the factor of the brand or the shade group (P resins; and were -2.0 to 1.8, -0.9 to 0.4 and -2.9 to 3.7, respectively, for indirect resins. Changes in TP were not significantly different by the type of resin, but those in FL and OP were different (P = 0.05). Changes in optical parameters were influenced by the brand or the shade group of the resins (P resins varied depending on type, brand or shade group. Aging significantly affected fluorescence and opalescence, but not translucency, of indirect resins compared to those of direct resins.

  15. The effect of processing on autohesive strength development in thermoplastic resins and composites

    Science.gov (United States)

    Howes, Jeremy C.; Loos, Alfred C.; Hinkley, Jeffrey A.

    1989-01-01

    In the present investigation of processing effects on the autohesive bond strength of neat polysulfone resin and graphite-reinforced polysulfone-matrix composites measured resin bond strength development in precracked compact tension specimens 'healed' by heating over a contact period at a given temperature. The critical strain energy release rate of refractured composite specimens did not exhibit the strong time or temperature dependence of the neat resin tests; only 80-90 percent of the undamaged fracture energy is recoverable.

  16. Histological evaluation to study the effects of dental amalgam and composite restoration on human dental pulp: an in vivo study.

    Science.gov (United States)

    Chandwani, Neelam D; Pawar, Mansing G; Tupkari, Jagdish V; Yuwanati, Monal

    2014-01-01

    To study and compare the effects of dental amalgam and composite restorations on human dental pulp. One hundred sound premolars scheduled for orthodontic extraction were divided equally into two groups: group A, teeth restored with silver amalgam, and group B, teeth restored with composite resin. Each group was equally subdivided into two subgroups [extracted after 24 h (A-1 and B-1) or 7 days (A-2 and B-2)], and the histological changes in the pulp related to the two different materials at the two different intervals were studied. It was found that after 24 h, the inflammatory response of the pulp in teeth restored with amalgam and composite was similar (p = 1.00). However, after 7 days, the severity of the inflammatory response of the pulp in teeth restored with amalgam was less compared to that in teeth restored with composite (p = 0.045). This study confirmed that amalgam continues to be the mechanically as well as biologically more competent restorative material. Composite could be a promising restorative material to satisfy esthetic needs for a considerable period of time. However, its biological acceptance is still in doubt. © 2013 S. Karger AG, Basel.

  17. The physical characteristics of resin composite-calcium silicate interface as part of a layered/laminate adhesive restoration.

    Science.gov (United States)

    Hashem, Danya F; Foxton, Richard; Manoharan, Andiappan; Watson, Timothy F; Banerjee, Avijit

    2014-03-01

    To compare in-vitro micro-shear bond strengths (μSBS) of resin composite to calcium silicate cement (Biodentine™) vs. glass ionomer cement vs. resin modified glass ionomer cement (RM-GIC) using an adhesive in self-etch (SE)/total etch (TE) mode after aging three substrates and bond and characterizing their failure modes. Resin composite was SE/TE bonded to 920 standardized disks of Biodentine™, GIC & RM-GIC. Dividing samples into two groups, the first underwent early (t=0min, 5min, 20min, 24h) or delayed (t=2wk, 1 month, 3 months, 6 months) substrate aging before bonding and μSBS (t=24h) testing. In the second, adhesive was applied after either early (t=5min) or delayed (t=2wk) substrate aging and then tested after bond aging (t=2wk, 1 month, 3 months, 6 months). The failure modes were identified using stereomicroscope. SEM images of selected samples were analyzed. No significant differences were observed between (SE)/(TE) bonding modes (P=0.42). With substrate aging, a significant reduction in μSBS occurred between early and delayed time intervals for Biodentine™ (P=0.001), but none for the GIC/RM-GIC (P=0.465, P=0.512 respectively). With bond aging, there was no significant difference between time intervals for all groups, except at 6 months for the GIC (PBiodentine™ is a weak restorative material in its early setting phase. Placing the overlying resin composite as part of the laminate/layered definitive restoration is best delayed for >2wk to allow sufficient intrinsic maturation to withstand contraction forces from the resin composite. A total-etch or self-etch adhesive may be used. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  18. Advanced resin systems and 3D textile preforms for low cost composite structures

    Science.gov (United States)

    Shukla, J. G.; Bayha, T. D.

    1993-01-01

    Advanced resin systems and 3D textile preforms are being evaluated at Lockheed Aeronautical Systems Company (LASC) under NASA's Advanced Composites Technology (ACT) Program. This work is aimed towards the development of low-cost, damage-tolerant composite fuselage structures. Resin systems for resin transfer molding and powder epoxy towpreg materials are being evaluated for processability, performance and cost. Three developmental epoxy resin systems for resin transfer molding (RTM) and three resin systems for powder towpregging are being investigated. Various 3D textile preform architectures using advanced weaving and braiding processes are also being evaluated. Trials are being conducted with powdered towpreg, in 2D weaving and 3D braiding processes for their textile processability and their potential for fabrication in 'net shape' fuselage structures. The progress in advanced resin screening and textile preform development is reviewed here.

  19. Shrinkage-stress kinetics of photopolymerised resin-composites

    Science.gov (United States)

    Satterthwaite, Julian D.

    The use of directly-placed substances as restorative materials in teeth remains the technique of choice for preserving function and form in teeth that have cavities. The current aesthetic restorative materials of choice are resin-composite materials, although these undergo molecular densification during polymerisation, which has deleterious effects. Although shrinkage-strain is the cause, it is the shrinkage-stress effects that may be seen as being responsible for the problems with adhesive resin-based restorations that are encountered clinically, the bond may fail with separation of the material from the cavity wall, leading to marginal discolouration, pulpal irritation and subsequent necrosis, post operative sensitivity, recurrent caries and eventual failure of restorations. Other outcomes include cohesive fracture of enamel or cusps, cuspal movement (strain) and persistent pain. The aims of this research were to characterise the effects of variations in resin-composite formulation on shrinkage-strain and shrinkage-stress kinetics. In particular, the influence of the size and morphology of the dispersed phase was investigated through the study of experimental formulations. Polymerisation shrinkage-strain kinetics were assessed with the bonded-disk method. It was found that resin-composites with spherical filler particles had significantly lower shrinkage-strain compared to those with irregular filler particles. Additionally, shrinkage-strain was found to be dependent on the size of filler particle, and this trend was related, in part, to differences in the degree of conversion. The data were also used to calculate the activation energy for each material, and a relationship between this and filler particle size for the irregular fillers was demonstrated. A fixed-compliance cantilever beam instrument (Bioman) was used for characterisation of shrinkage-stress kinetics. Significant differences were identified between materials in relation to filler particle size and

  20. In vitro enamel remineralization capacity of composite resins containing sodium trimetaphosphate and fluoride.

    Science.gov (United States)

    Tiveron, Adelisa Rodolfo Ferreira; Delbem, Alberto Carlos Botazzo; Gaban, Gabriel; Sassaki, Kikue Takebayashi; Pedrini, Denise

    2015-11-01

    This study evaluated the in vitro enamel remineralization capacity of experimental composite resins containing sodium trimetaphosphate (TMP) combined or not with fluoride (F). Bovine enamel slabs were selected upon analysis of initial surface hardness (SH1) and after induction of artificial carious lesions (SH2). Experimental resins were as follows: resin C (control—no sodium fluoride (NaF) or TMP), resin F (with 1.6% NaF), resin TMP (with 14.1% TMP), and resin TMP/F (with NaF and TMP). Resin samples were made and attached to enamel slabs (n = 12 slabs per material). Those specimens (resin/enamel slab) were subjected to pH cycling to promote remineralization, and then final surface hardness (SH3) was measured to calculate the percentage of surface hardness recovery (%SH). The integrated recovery of subsurface hardness (ΔKHN) and F concentration in enamel were also determined. Data was analyzed by ANOVA and Student-Newman-Keuls test (p Resins F and TMP/F showed similar SH3 values (p = 0.478) and %SH (p = 0.336) and differed significantly from the other resins (p resin TMP/F presented the lowest area of lesion (p resins (p = 0.042), but higher than in the other resins (p composite resin enhanced its capacity for remineralization of enamel in vitro. The combination of two agents with action on enamel favored remineralization, suggesting that composite resins containing sodium trimetaphosphate and fluoride could be indicated for clinical procedures in situations with higher cariogenic challenges.

  1. Avaliação clínica de uma resina composta modificada por poliácido, utilizada como selante oclusal, quando aplicada por dentista, THD e graduando Clinical evaluation of a polyacid-modified resin composite, used as an occlusal sealant, when applied by dentist, dental hygienist and undergraduate

    Directory of Open Access Journals (Sweden)

    Roberta Tarkany BASTING

    1999-04-01

    Full Text Available O presente trabalho tem por finalidade comparar as diferenças de retenção de uma resina composta modificada por poliácido (Variglass V.L.C., utilizada como selante oclusal, quando aplicada por dentista, THD e graduando em Odontologia. Foram seladas as superfícies oclusais de 370 primeiros molares permanentes superiores de crianças entre 6 e 8 anos de idade provenientes de escolas públicas do município de Piracicaba. As avaliações clínicas foram realizadas após seis e oito meses da aplicação do selante. Aos seis meses, verificou-se que 78,42% dos selantes clinicamente aceitáveis permaneceram retidos sobre a superfície oclusal. O índice de perdas totais corresponderam a 10,20% do total de selantes aplicados. O melhor índice de retenção total foi obtido quando aplicado por graduando. Aos 12 meses, houve um aumento do número de selantes perdidos (43,79% e conseqüente decréscimo do número de selantes totalmente retidos (18,96%, não havendo diferenças significativas de retenção do selante quando aplicado por dentista, THD e graduando. Nos casos de perdas totais do selante, não se constatou presença de lesão cariosa.The aim of this work is to evaluate the differences of clinical retention of a polyacid-modified resin composite (Variglass V.L.C., used as an occlusal sealant, when applied by dentist, dental hygienist and undergraduate in Dentistry. The occlusal surfaces of 370 superior first molars of children ageing from 6 to 8 years from public schools in Piracicaba, were sealed. The presented data are related to the final evaluation after 6 and 12 months. It was observed that after 6 months, 78.42% of the sealants clinically acceptable, remained on the occlusal surfaces and that the completely lost sealants reached 10.20%. The best results of the sealants retention were obtained when the sealants were applied by an undergraduate. After 12 months, there was an increase of completely lost sealants (43.79% and a decrease of

  2. Effect of surface conditioning methods on the microtensile bond strength of resin composite to composite after aging conditions

    NARCIS (Netherlands)

    Ozcan, Mutlu; Barbosa, Silvia Helena; Melo, Renata Marques; Galhano, Graziela Avila Prado; Bottino, Marco Antonio

    2007-01-01

    Objectives. This study evaluated the effect of two different surface conditioning methods on the repair bond strength of a bis-GMA-adduct/bis-EMA/TEGDMA based resin composite after three aging conditions. Methods. Thirty-six composite resin blocks (Esthet X, Dentsply) were prepared (5 mm x 6 mm x 6

  3. An evaluation of replacement rates for posterior resin-based composite and amalgam restorations in U.S. Navy and marine corps recruits.

    Science.gov (United States)

    Simecek, John W; Diefenderfer, Kim E; Cohen, Mark E

    2009-02-01

    Restoration replacement is a clinical concern that has not been studied among military personnel. The authors determined the prevalence of placement of posterior amalgam and resin-based composite restorations and the incidence of replacement among U.S. Navy and Marine Corps personnel. The authors analyzed dental records from 2,780 personnel to determine the relative risk of replacement for initially sound restorations during subjects' first years of military service. At the initial examination, 964 (15.2 percent) of amalgam restorations and 199 (17.4 percent) of resin-based composite restorations required re-treatment. Of those judged clinically acceptable, 14.2 percent of amalgam and 16.7 percent of resin-based composite restorations required replacement during the observation period. The authors found significant increases in replacement rates for resin-based composite restorations compared with amalgam restorations for replacement due to all causes (adjusted hazard ratio, 1.28; P composite restorations in place at the initial examination will require replacement than will amalgam restorations. Multi-surface restorations had higher rates of replacement than did one-surface restorations, and subjects at high caries risk experienced significantly higher replacement rates than did those at low caries risk. The number of surfaces restored and subjects' caries risk status may influence the longevity of resin-based composite and amalgam restorations.

  4. Shade distribution of commercial resin composites and color difference with shade guide tabs.

    Science.gov (United States)

    Park, Seung-Kook; Lee, Yong-Keun

    2007-10-01

    To determine the shade distribution of varied shades of contemporary resin composites, and to measure the color difference (deltaE*ab) between individual shades of resin composites and the nearest shade tabs, which showed the smallest color difference with each shade of resin composite, in the VITA shade guide. Eight light-curing resin composites, with a total of 41 shades, were studied. Color of specimens was measured on a reflection spectrophotometer over a white background. Ranges and distributions of CIE L*, C*ab, a* and b* values of each brand of resin composites were determined. Color difference between each shade of resin composites and each shade of the shade guide tabs were calculated, and the nearest shade guide tab was selected. The range of CIE L* value for eight brands of resin composites was 3.2-9.0, that of C*ab was 2.5-11.6, that of CIE a* value was 1.1-5.8, and that of CIE b* value was 5.9-11.5. Color differences (deltaE*ab) between each shade of resin composites and the nearest shade tab of the shade guide was 0.9-12.8.

  5. The effect of proximal contour on marginal ridge fracture of Class II composite resin restorations.

    NARCIS (Netherlands)

    Loomans, B.A.C.; Roeters, F.J.M.; Opdam, N.J.M.; Kuijs, R.H.

    2008-01-01

    OBJECTIVES: To compare the marginal ridge fracture strength of Class II composite resin restorations placed with a straight or contoured matrix band using composite resins with different modulus of elasticity. METHODS: In 60 artificial first molars standardized MO-preparations were ground. Two

  6. [Effect of bleaching agents on the color of indirect and direct composite resins].

    Science.gov (United States)

    Xing, Wenzhong; Jiang, Tao; Chen, Xiaodong; Wang, Yining

    2014-09-01

    To evaluate the effect of bleaching agents on the color of indirect and direct composite resins. Five resin composite materials were tested in this in vitro study. The five composites were as follow: two indirect composite resins (Adoro SR, Ceramage) and three direct composite resins (Filtek Z350, Clearfil Majesty Esthetic, and Gradia Direct Anterior). For each material, twenty disk-shaped specimens were prepared and randomly divided into five groups according to the color parameters of specimens before bleaching treatment. The composite resin specimens were treated by one of five sample solutions which were at-home bleaching agents (10% and 15% carbarmide peroxide), in- office bleaching agents (38% H(2)O(2) and 35%H(2)O(2)) and deionized water (control group). The color parameters of specimens were measured by spectrophotometer at baseline and after bleaching treatments. The color differences (ΔE values) between baseline and post-treatments were calculated. The data of color differences were evaluated statistically using two-way analysis with a significance level of 0.05. The color changes of the resin composites were less than 2.0 after bleaching agent treatment, therefore were not perceptible. Slight increase of L(*) values and decrease of C(*)ab values in color parameters of specimens were observed. There were statistically significant differences in ΔE values for different bleaching treatments and resin materials (P = 0.001). The bleaching agents did not affect the color of indirect and direct composite resins tested.

  7. Composite panels made with biofiber or office wastepaper bonded with thermoplastic and/or thermosetting resin

    Science.gov (United States)

    James H. Muehl; Andrzej M. Krzysik; Poo Chow

    2004-01-01

    The purpose of this study was to evaluate two groups of composite panels made from two types of underutilized natural fiber sources, kenaf bast fiber and office wastepaper, for their suitability in composite panels. All panels were made with 5% thermosetting phenol-formaldehyde (PF) resin and 1.5% wax. Also, an additional 10% polypropylene (PP) thermoplastic resin was...

  8. The effectiveness of different polymerization protocols for class II composite resin restorations.

    NARCIS (Netherlands)

    Jong, L.C.G. de; Opdam, N.J.M.; Bronkhorst, E.M.; Roeters, F.J.M.; Wolke, J.G.C.; Geitenbeek, B.

    2007-01-01

    OBJECTIVES: To investigate the effect of reduced light exposure times on Vickers hardness (VH) of class II composite resin restorations. METHODS: Class II restorations were made in vitro in three 2mm thick increments in a human molar. Two composite resins (Clearfil AP-X; Esthet-X) were polymerized

  9. Clinical success and survival of indirect resin composite crowns: results of a 3-year prospective study

    NARCIS (Netherlands)

    Jongsma, L.A.; Kleverlaan, C.J.; Feilzer, A.J.

    2012-01-01

    Objectives The aim of this study was to test the new resin composite "NECO" as a material for indirect restorations clinically. Methods Forty-five patients were selected, of which 12 men and 33 women, with a mean age of 53. A total of 91 post-canine indirect resin composite NECO (Heraeus Kulzer,

  10. Influence of salivary enzymes and alkaline pH environment on fatigue behavior of resin composites

    NARCIS (Netherlands)

    Mirmohammadi, H.; Kleverlaan, C.J.; Aboushelib, M.N.; Feilzer, A.J.

    2011-01-01

    Purpose: To evaluate the effect of enzymatic activity and alkaline medium on flexural strength and rotary fatigue resistance of direct and indirect resin composite restorative materials. Methods: Three direct resin composite materials Filtek Z100, Filtek Z250 and Filtek Silorane (3M ESPE), and two

  11. The bond of different post materials to a resin composite cement and a resin composite core material.

    Science.gov (United States)

    Stewardson, D; Shortall, A; Marquis, P

    2012-01-01

    To investigate the bond of endodontic post materials, with and without grit blasting, to a resin composite cement and a core material using push-out bond strength tests. Fiber-reinforced composite (FRC) posts containing carbon (C) or glass (A) fiber and a steel (S) post were cemented into cylinders of polymerized restorative composite without surface treatment (as controls) and after grit blasting for 8, 16, and 32 seconds. Additional steel post samples were sputter-coated with gold before cementation to prevent chemical interaction with the cement. Cylindrical composite cores were bonded to other samples. After sectioning into discs, bond strengths were determined using push-out testing. Profilometry and electron microscopy were used to assess the effect of grit blasting on surface topography. Mean (standard deviation) bond strength values (MPa) for untreated posts to resin cement were 8.41 (2.80) for C, 9.61(1.88) for A, and 19.90 (3.61) for S. Prolonged grit blasting increased bond strength for FRC posts but produced only a minimal increase for S. After 32 seconds, mean values were 20.65 (4.91) for C, 20.41 (2.93) for A, and 22.97 (2.87) for S. Gold-coated steel samples produced the lowest bond strength value, 7.84 (1.40). Mean bond strengths for untreated posts bonded to composite cores were 6.19 (0.95) for C, 13.22 (1.61) for A, and 8.82 (1.18) for S, and after 32 seconds of grit blasting the values were 17.30 (2.02) for C, 26.47 (3.09) for A, and 20.61 (2.67) for S. FRC materials recorded higher roughness values before and after grit blasting than S. With prolonged grit blasting, roughness increased for A and C, but not for S. There was no evidence of significant bonding to untreated FRC posts, but significant bonding occurred between untreated steel posts and the resin cement. Increases in the roughness of FRC samples were material dependent and roughening significantly increased bond strength values (ptested FRC posts is required for effective bonding.

  12. Process Optimization of Bismaleimide (BMI) Resin Infused Carbon Fiber Composite

    Science.gov (United States)

    Ehrlich, Joshua W.; Tate, LaNetra C.; Cox, Sarah B.; Taylor, Brian J.; Wright, M. Clara; Caraccio, Anne J.; Sampson, Jeffery W.

    2013-01-01

    Bismaleimide (BMI) resins are an attractive new addition to world-wide composite applications. This type of thermosetting polyimide provides several unique characteristics such as excellent physical property retention at elevated temperatures and in wet environments, constant electrical properties over a vast array of temperature settings, and nonflammability properties as well. This makes BMI a popular choice in advance composites and electronics applications [I]. Bismaleimide-2 (BMI-2) resin was used to infuse intermediate modulus 7 (IM7) based carbon fiber. Two panel configurations consisting of 4 plies with [+45deg, 90deg]2 and [0deg]4 orientations were fabricated. For tensile testing, a [90deg]4 configuration was tested by rotating the [0deg]4 configirration to lie orthogonal with the load direction of the test fixture. Curing of the BMI-2/IM7 system utilized an optimal infusion process which focused on the integration of the manufacturer-recommended ramp rates,. hold times, and cure temperatures. Completion of the cure cycle for the BMI-2/IM7 composite yielded a product with multiple surface voids determined through visual and metallographic observation. Although the curing cycle was the same for the three panellayups, the surface voids that remained within the material post-cure were different in abundance, shape, and size. For tensile testing, the [0deg]4 layup had a 19.9% and 21.7% greater average tensile strain performance compared to the [90deg]4 and [+45deg, 90deg, 90deg,-45degg] layups, respectively, at failure. For tensile stress performance, the [0deg]4 layup had a 5.8% and 34.0% greater average performance% than the [90deg]4 and [+45deg, 90deg, 90deg,-45deg] layups.

  13. Effects of Topical Fluoride on the Marginal Microleakage of Composite Resin and Resin-Modified Glass Ionomer Restorations in Primary Molars: An In-vitro Study

    Directory of Open Access Journals (Sweden)

    Fatemeh Mir

    2017-12-01

    Full Text Available Introduction: Topical