WorldWideScience

Sample records for denki kagaku tokusei

  1. Fundamental characteristics on electric system of solar electric vehicle; Solar car no denki keito ni kansuru kiso tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, S.; Sasaki, M.; Kaga, T.; Koyama, N. [Hachinohe Institute of Technology, Aomori (Japan)

    1996-10-27

    The electric system of a solar vehicle was removed and the fundamental characteristics examined in order to carry out a basic experiment on the electric system. Using a basic circuit with panels, batteries and loads connected, the voltage and current were measured in the presence/absence of the trackers, batteries, etc., and then, their effects were examined. Simultaneously, the quantity of solar radiation was also measured. The lowering of the output voltage was somewhat relaxed with the use of the trackers. Further, with the trackers used, the output voltage of the panel was small in spite of a large quantity of solar radiation compared to the case without the trackers, which was due to the restriction of the output voltage by the trackers. When measured without batteries, the output voltage of the panel was such that the load current was also influenced by the variation of insolation, so that, with a large decrease in insolation, the load current was decreased with the supply of current suspended from the panel. 7 figs., 1 tab.

  2. Coal Liquefaction characteristics and chemical structure of product oil; Sekitan ekika hanno tokusei to seiseibutsu no kagaku kozo

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H.; Sato, M.; Chiba, T.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Sasaki, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Through the hydrogenolysis of Wandoan coal and Tanito Harum coal which are used for the NEDOL process, differences of liquefaction characteristics between them were found. The purpose of this study is to grasp these differences as differences of chemical structures of oil fractions. The compound type analysis was conducted for oil fractions obtained at varied reaction temperature for varied reaction time. Coal liquefaction characteristics of these coals were discussed by relating oil yields and chemical structures. For Tanito Harum coal, yields of gas and oil were considered to be lower than those for Wandoan coal, which reflected that the contents of partially hydrogenated hydroaromatics in oil fraction from the former were lower than those from the latter, and that the remarkable change of composition did not occur with the progress of the reaction. For both the coals, the remarkable changes in the average molecular weight of oil fraction were not observed with the progress of the reaction. While, the content of methane gradually increased with the progress of the reaction, which suggested that oil was gradually dealkylated. 5 figs.

  3. Report on research results of the FY 2000 medical/engineering cooperative research project. Fundamental research on microelectrode-aided gene information measurement system (Research and development of gene diagnostic system using superhigh-sensitivity microelectrode DNA chip ECA - electrochemical array); 2000 nendo igaku kogaku renkeigata kenkyu jigyo kenkyu seika hokokusho. Bisho denkyoku riyo idenshi joho keisoku system ni kansuru kiban kenkyu (chokokandogata bisho denkyoku DNA chip ECA (denki kagaku allay) wo mochiita idenshi shindan system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fundamental research is conducted for developing the microelectrode on which a synthetic oligonucletide probe is immobilized, and for establishing the system capable of detecting the hybrid formation simply and quickly, in order to develop the advanced DNA chips for diagnosis. The project results include development of the prototype array electrode with 25 1mm-diameter gold electrodes uniformly arranged at intervals of 4.5mm; development of the electrochemical activity analyzer for multi-electrode systems, showing the performance almost on a level with that of the existing electrochemical analyzer for the single-electrode systems; establishment of the gene databases; development of the method which can produce a sufficient quantity of nucleic acid for DNA chip analysis by studying the method of preparing the nucleic acid from the blood serum, preparing RNA from a trace quantity of the living liver sample and amplifying the genes, wherein the nucleic acid is produced while its profile before the amplification is kept intact; and establishment of the method for detecting the hepatitis B virus by combining the electrochemical detection of DNA by a non-immobilized probe with the PCR method. (NEDO)

  4. Introduction of electric double layer capacitors in the solar-EV; Solar denki jidosha eno denki nijuso condenser no oyo

    Energy Technology Data Exchange (ETDEWEB)

    Fujinaka, M. [Tokyo Denki University, Tokyo (Japan)

    1996-10-27

    A basic experiment was carried out on a supplementary power supply, in which solar cells and electric double layer capacitors(EDLC) were combined for a DC/DC converter, for the use of a solar-electric vehicle (S-EV); and in actuality, an S-EV was loaded with the power supply with a running test conducted on a public road. The EDLC was found effective and useful for avoiding temporary lowering of voltage and momentary break. An electric supply was thereby made possible for an emergency light without the use of the DC/DC converter. However, in a tunnel or a night driving and in case of failure of the DC/DC converter, an operating time of only 7 minutes or so was affordable with the EDLC having a capacity of 100F. Moreover, particularly with a heavy load, it was impossible to maintain a voltage for many hours. Under the circumstances, an S-EV design would primarily require two sets of independent DC/DC converter loaded in the future. The EDLC, young after it was developed, still has a small energy density compared with a lead storage battery. Yet, an EDLC with a higher performance being developed, there is a possibility that it will be applied to S-EV`s by utilizing its characteristics such as a high efficiency and a long service life. 4 refs., 8 figs.

  5. Mongolian coal liquefaction test; Mongorutan no ekika tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Kubo, H. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Tsedevsuren, T. [National Research Center of Chemistry and Technology of Coal in Mongoria (Mongolia)

    1996-10-28

    This paper describes the results of liquefaction tests of Mongolian coals using an autoclave and a flow micro reactor. Uvdughudag coal, Hootiinhonhor coal, and Shivee-Ovoo coal were used for liquefaction tests with an autoclave. Oil yields of Uvdughudag and Hootiinhonhor coals were 55.56 wt% and 55.29 wt%, respectively, which were similar to that of Wyoming coal. Similar results were obtained, as to produced gas and water yields. These coals were found to be suitable for coal liquefaction. Lower oil yield, 42.55 wt% was obtained for Shivee-Ovoo coal, which was not suitable for liquefaction. Liquefaction tests were conducted for Uvdughudag coal with a flow micro reactor. The oil yield was 55.7 wt%, which was also similar to that of Wyoming coal, 56.1 wt%. Hydrogen consumption of Uvdughudag coal was also similar to that of Wyoming coal. From these, Uvdughudag coal can be a prospective coal for liquefaction. From the distillation distribution of oil, distillate fraction yield below 350{degree}C of Uvdughudag coal was 50.7 wt%, which was much higher than that of Wyoming coal, 35.6 wt%. Uvdughudag coal is a coal with high light oil fraction yield. 2 figs., 5 tabs.

  6. Small gap test of electric detonators. Denki raikan no kogata gap shiken

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, A.; Matsuzawa, T.; Yoshida, N. (Nippon Kayaku Co. Ltd., Tokyo (Japan)); Wada, Y.; Yahashi, H.; Tamura, S.; Yoshida, T. (The Univ. of Tokyo, Tokyo (Japan). Faculty of Engineering)

    1990-06-30

    An electric detonator is an important ammunition for initiating explosive. Since it has a high dangerousness in its handling, various measures for the transportation and the storage are being studied. In this paper, small gap test was taken as a preliminary test to assess safety package of electric detonators. Meanwhile, to examine the effect of cushioning materials, five kinds of materials such as styrene foam and river sand were used as specimen. Shock sensitivity of the detonator depended on a position which was added a shock from the detonator. Positions where contain more sensitive explosives showed more sensitivity. River sand and phenol foam absorbed shock wave from detonators more effectively than other materials which were tested, and were thought to be useful as a buffer for preventing the sympathetic detonation. In the underwater small gap test, different gap materials, i.e. cards or sticks, gave different results, though the total gap lengths were same. Critical gap lengths were also different in air and underwater. These results are the subjects to be studied in future. 5 refs., 3 figs., 2 tabs.

  7. Field tests of electric survey using capacitive electrodes; Kyapashita denkyoku wo mochiita denki tansarei

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, I.; Iseki, S.; Kobayashi, T. [OYO Corp., Tokyo (Japan)

    1997-10-22

    This paper describes field test results of electric survey using capacitive electrodes. When two metal plates are approached without contacting with the ground and voltage is applied between the plates, current flows in the ground. The metal plates and the ground work as a capacitor. Charges are stored between them. These metal plates having insulation with the ground are called capacitive electrodes. When ac voltage is applied between a pair of capacitors, current flows continuously in the ground without saturating the capacitors. Resistivity of the ground can be determined by measuring the level of current flowing in the ground and the level of potential. As a result of the field tests, it was found that the present method is superior to the conventional method in around ten times. However, to obtain high quality data, water spraying, reduced towing speed at the low resistivity ground such as clay and soil, and grass mowing are required. 3 refs., 5 figs., 1 tab.

  8. Development and environment of new electric automobile, `Ecovehicle`; Shingata denki jidosha eko vehicle kaihatsu to kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, H. [National Inst. for Environmental Studies, Tsukuba (Japan)

    1996-10-27

    This paper introduces history of the development of an electric automobile, `Ecovehicle`. It is provided with a high overall energy efficiency compared with an engine vehicle. The Ecovihicle is 1.2m in width, 3.3m in length, 2 seating capacities and 910kg in overall weight with serially connected 56 batteries of each 4V, 40Ah and having the total weight of 269kg. Its travel distance per charging is 130km at a speed of 80 k.p.h. This vehicle is capable of running with an energy of approximately one third as much as that of a light car. In addition, the vehicle is provided with polycrystal solar batteries placed on 0.6m{sup 2} area on the roof and spoiler generating 60W maximum. Assuming the annual duration of sunshine is 1,800 hours, charging is possible for 63kWh annually. Assuming the charging efficiency is 83%, charging is possible about seven times, which is an equivalent of travelling about 1,000km annually. The characteristics for example are the employment of brushless DC motor, use of energy saving switching element IGBT in order to realize a low level of loss in the inverter, in-wheel motor system, and storage of storage batteries in a hollow aluminum frame installed under the floor. 2 refs., 5 figs., 1 tab.

  9. Development of measurement apparatus for high resolution electrical surveys; Komitsudo denki tansa sokuteiki no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Moriuchi, H.; Matsuda, Y.; Shiokawa, Y. [Sumiko Consultants Co. Ltd., Tokyo (Japan); Uchino, Y. [Cosmic Co. Ltd., Tokyo (Japan)

    1996-05-01

    For the enforcement of the {rho}a-{rho}u survey method which is a type of high-density electrical survey, a multichannel resistivity measuring instrument has been developed. This instrument, in addition to the above, conducts resistivity tomography and various other kinds of high-density electrical survey. A potential produced by a low frequency rectangular current of 1Hz or lower outputted by the transmitter of this instrument is received and measured by the receiver connected to electrodes positioned at 100 or less locations. The receiver comprises a scanner that automatically switches from electrode to electrode, conditioner that processes signals, and controller. A transmitter of the standard design outputs a maximum voltage of 800V and maximum current of 2A, making a device suitable for probing 50 to several 100m-deep levels. The receiver is operated by a personal computer that the controller is provided with. The newly-developed apparatus succeeded in presenting high-precision images of the result of a {rho}a-{rho}u analysis for an apparent resistivity section and of the underground structure, verifying the high quality of the data collected by this apparatus. 10 refs., 5 figs., 1 tab.

  10. Ground water contamination by electrical prospecting; Denki tansaho ni yoru chikasui osen chosa

    Energy Technology Data Exchange (ETDEWEB)

    Irie, S.; Fujii, Y.; Sakaguchi, S.; Ushijima, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-05-01

    A report is made about the result of vertical electric sounding conducted in the MK district, Fukuoka City, where Kyushu University is about to move. As for the method of electrical prospecting, in consideration of the need for probing a depth of 50m at the shallowest, vertical electrical sounding with a Schlumberger array of electrodes was employed. Measurements were made for 57 locations on the planar ground, the interval between electrodes gradually increased from 1 to 200m. In the 2D structure model analysis, a 2D inversion program was utilized in the ABIC minimization method. Also investigated were the relationship of electric prospecting and the geology, geological conditions, water level in the well, water quality, salt water, and pore rate from the previously-conducted investigative boring. As the result, it was estimated that the boundary between the first and second layers detected by electric prospecting reflected the level of underground water and that the boundary between the second and third layers reflected the portion where the N-value sharply increases. 4 refs., 8 figs.

  11. Development of practical solar-electric vehicle; Jitsuyo fukyugata solar denki jidosha no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, S.; Fujinaka, M. [Tokyo Denki University, Tokyo (Japan)

    1997-11-25

    The paper reported on a Tokyo-Nagoya travel test on a practical spread type solar-electric vehicle, Solar-EV. A comparative study was made running the same type gasoline vehicle, GV. The measured power consumption amount of Solar-EV is 57.6 kWh. By converting it into Mcal unit, an energy consumption amount of 49.5 Mcal was obtained. Further, as to GV, the energy consumption amount of 316 Mcal was obtained using the amount of supply of gasoline (mean heating value: 8.4 Mcal/h) of 37.6 l and the fuel consumption of 16.2 km/l. Accordingly, the energy consumption amount of Solar-EV became a sixth of that of GV. In the cost comparison, the cost of Solar-EV was 1,440 yen (power source price: 25 yen/kWh), which is about a third of that of GV, 3760 yen (gasoline unit price: 100 yen/l). Monocrystal Si solar cells, 270W, installed on hood/roof are connected to the main 288V system (the auxiliary 12V system is amorphous Si), and generate power 4.4 kWh during travel. A total power consumption amount of Solar-EV in the total travel (Tokyo-Nagoya) is 79.9 kWh including the auxiliary system, approximately 6% of which was to be supplied from solar cells. 1 ref., 6 figs., 3 tabs.

  12. Microchemical device based on microscopic bilayer lipid membranes; Bisho 2 bunshimaku wo mochiiita maikuro kagaku debaisu

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, H. [Electrotechnical Lab., Ibaraki (Japan)

    1996-04-01

    If an organism is regarded as a macromolecular system, the element device to construct the same is the molecular structure of nano meter scale formed by the functional protein existing in biomembranes. A lot of essential functions of organism such as the sense reception including vision, gustation, etc., photosynthesis, energy-substance production and so on are performed therein. In this paper, the structure, preparing process and the functions of the microchemical device using micro-bilipid membranes are described. The simulation of the sense receiving functions of organisms is tried by said microchemical device wherein, same as biomembranes, the base is bilayer lipid molecular membrane and the receptive protein for receiving signals from exterior and output molecules such as ion channels connected to said receptive protein and the like are incorporated in the membranes. Recently, it becomes possible to make a partial imaging of the bilayer lipid membranes fixed on porous membrane by the observation with scanning Maxwell-stress microscope. 4 refs., 3 figs.

  13. Safety (management and technology). Safety of chemical materials; Anzen (manejimento to tekunoroji). Kagaku busshitsu no anzensei

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T. [Hosei Univ., Tokyo (Japan). Faculty of Engineering

    1994-08-05

    In chemical materials there exist hazardous materials causing health damages, environmental pollution, fires and explosions. The hazard analysis has been noted as a means for preventing accidents due to chemical materials. This means leads to an effective method of recognizing hazard, evaluating the risk, and lowering the degree of hazard to an allowable level. This paper describes a hazard analysis of autoreactive materials, out of chemical materials causing fires and explosions, which may react by theirselves and cause accidents. In particular, an example is introduced in which this hazard analysis method is adapted to an experimental production of the next generation gas generating agent for automobile collision safety air-bags. In this manufacturing process, in kneading and granulating processes where lots of materials are handled, materials are used in a moistened state, thus countermeasures for preventing occurrence of combustion and explosion being taken. 5 refs., 2 figs., 4 tabs.

  14. Analysis and scavenging effect of acid fog. Sanseimu no kagaku sosei to senjo koka

    Energy Technology Data Exchange (ETDEWEB)

    Igawa, M.; Hoka, E.; Hosono, T.; Iwase, K.; Nagashima, T. (Kanagawa University, Yokohama (Japan). Faculty of Engineering)

    1991-05-10

    Fog samples were collected for analysis at Mt. Ohyama, the east edge of Tanzawa Mountains in the southwest of Kanto plains. Then, rainwater and aerosol that becomes the core of droplet were analyzed and measured values were compared. As a result, the pH value of the fog samples for 2 years from 1988 to 1990 ranged between 2.6 and 7.0, and the mean pH value was 3.95. According to the measurement of major component concentration of fogwater, rainwater, and aerosol, it was found that concentration of fogwater changed significantly depending on the day but every ion concentration was higher than that of rainwater. The equivalent concentration ratio of sulfuric acid, nitric acid, and chloride ions were almost equal. The concentration value of fogwater varied a lot with the course of time and became higher during the formation and the dissipation of fog. Through the analysis of such changes, atmospheric scavenging effect of precipitation of fogwater upon the trees and the earth surface was observed. It means that pollutants with high concentration were loaded on the plants and the earth surface. 23 refs., 5 figs., 2 tabs.

  15. Electric and VLF-MT survey of Tegatayama tunnel; Tegatayama tunnel no denki tansa oyobi VLF tansa

    Energy Technology Data Exchange (ETDEWEB)

    Nishitani, T. [Akita University, Akita (Japan). Mining College

    1997-05-27

    To survey the structure at the depth between 20 and 30 m, field tests were conducted by means of vertical electric and VFL-MT (magnetotelluric) survey. Tegatayama tunnel has a total length of 276 m, width of 7.5 m, and height of 4.7 m, and the depth from the surface is about 28 m near the top of mountain. Near the tunnel, the thickness of surface soil is about 60 cm, which consists of clay soil including soft mudstone gravel. It was found that terrace deposit is distributed up to the depth of 8 m, and that mudstone is distributed below the depth of 8 m. Weighted four-electrode method was adopted for the vertical electrical survey. Measurements were conducted at the immediately above the tunnel, 10 m apart from the center of tunnel in the right and left, and 20 m apart from the center in the east. For the VLF-MT method, component of frequency 22.2 kHz was used. As a result of the tests, it was difficult to illustrate the existence of tunnel from the vertical electrical survey only at one point. Feature of the tunnel could be well illustrated by means of the VLF-MT method. 3 refs., 9 figs.

  16. Neck electrical impedance for measurement of swallowing; Enge katsudo no keisoku no tame no keibu denki impedance

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Y. [Okayama University, Okayama (Japan)] Nakamura, T. [Okayama University, Okayama (Japan). School of Health Science; Utsunomiya, K.; Akashi, K. [Kawasaki Medical School, Kawasaki (Japan)] Jikuya, K. [Kawasaki College of Allied Health Professions, Kawasaki (Japan)

    1998-03-01

    Recently videofluorography has been used for evaluation of swallowing function in rehabilitation field. But it is not easy to evaluate swallowing disorder simply. And it has problems or exposure for daily use. We have proposed a measurement method of swallowing using bioelectrical impedance method (Impedance Pharyngography, IPG) which has advantages of easy handle and non-invasive measurement. Appropriate electrode positions have been determined. The waveform of IPG can be obtained with some extent reproducibility. The change of neck electrical impedance in pharyngeal phase is mainly caused by the changes of equivalent cross sectional area of near epiglottis. The possibilities of applications for clinical diagnosis have been shown. 7 refs., 10 figs.

  17. Monitoring of IOR/EOR operations by electrical prospecting; Denki tansaho ni yoru IOR/EOR monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Ushijima, K.; Mizunaga, H.; Ikeda, H.; Masuda, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-10-01

    Fluid flow tomography (FFT) was developed to monitor enhanced oil recovery IOR/EOR operations. This method uses a casing pipe as linear current source by connecting a current electrode with a well inlet, and the other electrode is grounded at a point far different from the well. Potentials are rapidly measured at the same time by multi-channel receiving electrodes installed on the ground to obtain time series data composed of charged potential and superimposed spontaneous potential. After separation of both potentials, the charged potential data are processed by the conventional mise-a-la-masse method to extract local anomaly, determine the residual distribution and relative change distribution of time-sliced apparent resistivity, and obtain the 3-D profile of fluid. The spontaneous potential is also processed to obtain the deflection distribution of time-sliced potential at a specific time. Quantitative 3-D interpretation is conducted focusing attention on the generation mechanism of spontaneous potential. Behavior of underground permeated flow is determined as time series animation images to image fluid direction. This method was effective in real fields. 8 refs., 4 figs.

  18. Monitoring of EOR operations by electrical prospecting. 2; Denki tansaho ni yoru sekiyu kyosei kaishuho no monitoring. 2

    Energy Technology Data Exchange (ETDEWEB)

    Ushijima, K.; Mizunaga, H.; Tanaka, T.; Masuda, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tamagawa, T. [Japex Jeoscience Institute, Tokyo (Japan)

    1996-10-01

    Fluid flow tomography (FFT) was applied to monitor the behavior of underground fluid in steam enhanced oil recovery (EOR) for oil sand reservoirs. FFT uses electrode arrangement of a mise-a-la-masse method, and continuously measures time variation in charged and spontaneous potential at various surface points to obtain realtime the images of underground seepage flow. It continuously measures ground surface potentials of 120 channels at intervals of 2s by applying alternative DC between a casing pipe and distant current electrode. It separates charged and spontaneous potential components, and converts them into time series data. It estimates the time and spacial distributions of seepage flow from time variation in spontaneous potential. It determines the change rate distribution of time-sliced apparent resistivity from charged potential to estimate the scale and area of seepage flow. As the experimental result, positive and negative electrodes in the change rate distribution were observed, and the direction connecting each electrode agreed with that of resistivity anomaly. FFT could observe realtime time variation in apparent resistivity due to steam injection. 9 refs., 7 figs.

  19. Toward promotion of recycling electric and electronic devices; Denki denshi kiki no recycle no sokushin ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    Measures for promotion of recycling electric and electronic devices are discussed and proposed. It is necessary to change the traditional framework of recycling in which local governments are required to play major roles. It is also necessary to set more clear responsibilities and expenses to be shared by the parties concerned, establish rules for recovering expenses to keep fairness among the parties concerned, and develop measures to promote smooth recovery and recycling of electric and electronic devices. The framework should be based on market principle, to introduce various types of competition, thereby reducing social expenses as far as possible. It is necessary for all parties to share responsibilities for establishing recycling type economic society; makers and importers should supply durable and recyclable products and implement recovery and recycling of the used products they supply to a required level, and, at the same time, consumers should release the used products in the recycling systems. 3 figs., 1 tab.

  20. Study on solar collector utilizing electro-hydrodynamical effect; Denki ryutai rikigaku koka wo riyosuru taiyo shunetsuki no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Aoki, H.; Wako, Y. [Hachinohe Institute of Technology, Aomori (Japan)

    1997-11-25

    This paper proposes a cone type electro-hydrodynamical (EHD) heat collector, describes its structure and principle, and mentions possibility of improving the heat collecting efficiency. The paper proposes a heat collector with a shape close to a cone. Trees are of cone form so that their every leaf, branch and truck can capture solar energy efficiently. Imitating this fact existing in the natural world, a cone-shaped heat collector was fabricated on a trial basis to discuss its heat collecting efficiency. Furthermore, black round stones are placed in the inner cone of the cone- shaped heat collector of double-glass structure. A low boiling point medium is placed between the inner and outer cones to cause corona discharge in vapor generated by absorbing the solar heat, and generate corona wind for an attempt to accelerate heat transfer into a heat exchanger. Thus, development was made on a cone-shaped high-efficiency heat collector utilizing electro-hydrodynamical (EHD) effect, and elucidation was given on dynamic phenomena of an electro-thermal fluid. Heat transfer in the EHD heat collector has a possibility of being accelerated by generation of ionic wind. In addition, it is thought that there would be an optimum value in applied voltage to increase electric charge supply as a result of corona discharge. 1 ref., 2 figs.

  1. Heat transfer characteristics in a pulsated fluidized bed in relation to bubble characteristics; Parusu ryudoso no dennetsu tokusei to kiho tokusei tono sokan

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, A.; Hasatani, M. [Nagoya Univ., Nagoya (Japan). Dept. of Energy Engineering and Science; Deguchi, S. [Nagoya Univ., Nagoya (Japan). Center for Integrated Research inn Science and Engineering; Matsuda, H. [Nagoya Univ., Nagoya (Japan). Research Center for Advanced Waste and Emission Management; Mujumdar, A.S. [McGill Univ., Quebec (Canada). Dept. of Chemical Engineering

    2000-11-10

    A pulsated fluidized bed is operated with two sequential duration designated as the on-period with injecting fluidization air, and the off-period without injecting fluidization air. The heat transfer coefficient between a vertically immersed heater and bed in a pulsated fluidized bed is measured under various pulse cycles and fluidized particles. The obtained results are compared with those in a normal fluidized bed with continuous fluidization air injection. The relation between heat transfer coefficient and bubble characteristics, evaluated by using a digital video camera, was investigated. For certain fluidized particles and operated pulse cycles, fluidization of particles and increment of heat transfer coefficient can be obtained under lower mean air velocity based on a pulse cycle duration than minimum fluidization air velocity of the normal fluidized bed. Under the pulse cycles where a static ed is formed in off-period duration, the improved heat transfer rate in contrast with the normal fluidized bed can be measured. This because of the large bubbles formation. As the heat transfer in the pulsated fluidized bed is obstructed with increasing time to keep a static bed due to the excess of-period duration it is indicated that there is an optimum off-period duration based on the heat transfer rate. (author)

  2. Agglomeration and reaction characteristics of various coal chars in fluidized-bed coal gasifier; Ryudoso sekitan gas ka ronai deno sekitan no gyoshu tokusei to hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Uemiya, S.; Aoki, K.; Mori, S.; Kojima, T. [Seikei University, Tokyo (Japan). Faculty of Engineering

    1996-10-28

    With relation to the coals delivered as common samples in the coal fundamental technology development project, an experimental study was conducted on agglomeration characteristics and reaction characteristics in the fluidized-bed coal gasifier. For the experiment, used was a fluidized bed gasifier inserted with a cone-shape dispersion plate with a nozzle in the center. After raising the temperature of the gasifier up to 773K, gasification was conducted sending to the gasifier air from the nozzle and steam from the dispersion plate. The mean particle diameter and gas concentration of chars were measured till the temperature reaches 1373K. As a result of the experiment, it was confirmed that the carbon conversion ratio increases with a decrease in coalification degree of the coal. Moreover, influence of the coal kind was markedly observed at the grid zone of the lower part of the bed, and it was clarified that the lower carbon content ratio the coal kind has, the faster the speed of CO formation and water gasification get. The agglomeration temperature of charcoal which is a product of the condensate is lower by as many as several hundred K than the point of softening, and it was considered to be necessary to study the relation with the temperature distribution in the bed. 3 refs., 3 figs., 1 tab.

  3. Identification of modal parameters and spatial matrix in frequency domain. Basic theory; Shuhasu ryoiki ni okeru mode tokusei to tokusei gyoretsu no dotei. Kiso riron no kento

    Energy Technology Data Exchange (ETDEWEB)

    Iwahara, M. [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Sugiura, T.; Takaiwa, H.; Nagamatsu, A. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    An approach is presented for the identification of spatial matrix with modal parameters in the frequency domain. Modal parameters are transformed to spatial matrix with constraints of modal vector orthogonality and characteristic equation. Adding the connecting conditions or unconnected conditions of measuring points, spatial matrix is determined by modal parameters whose number is smaller than that of dimension of spatial matrix. 9 refs., 4 figs., 2 tabs.

  4. Sorption phenomena of methanol on heat treated coal; Netsushori wo hodokoshita sekitan no methanol kyuchaku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, H.; Kaiho, M.; Yamada, O.; Soneda, Y.; Kobayashi, M.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Experiments were carried out to learn methanol sorption characteristics of heat-treated coal. When Taiheiyo coal is heat-treated at 125{degree}C, performed with a first methanol adsorption at 25{degree}C, and then desorption at 25{degree}C, a site with strong interaction with methanol and a site with relatively weak interaction are generated in test samples. A small amount of methanol remains in both sites. Then, when the methanol is desorbed at as low temperature as 70{degree}C, the methanol in the site with strong interaction remains as it has existed therein, but the methanol in the site with relatively weak interaction desorbs partially, hence the adsorption amount in a second adsorption at 25{degree}C increases. However, when desorption is performed at as high temperature as 125{degree}C, the methanol in the site with strong interaction also desorbs, resulting in increased adsorption heat in the second adsorption. The adsorption velocity drops, however. Existence of methanol in a site with strong interaction affects the adsorption velocity, but no effect is given by methanol in a site with weak interaction. 3 refs., 4 figs.

  5. Reservoir characterization using artificial neural network; Neural network wo mochiita choryuso tokusei kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, N.; Kozawa, T. [Japan National Oil Corp., Tokyo (Japan); Nishikawa, N.; Tani, A. [Fuji Research Institute Corp., Tokyo (Japan)

    1997-05-27

    Neural network is used for the prediction of porosity and permeability using logging data as reservoir characteristics, and the validity of this method is verified. For the prediction of reservoir characteristics by the use of seismic survey data, composite seismic survey records obtained by density logging and acoustic logging are used to experiment the prediction of porosity and permeability continuous along lines of wells. A 3-output back propagation network is used for analysis. There is a possibility that this technique when optimized will improve on prediction accuracy. Furthermore, in the case of characteristics mapping, 3-dimensional seismic data is applied to a carbonate rock reservoir for predicting spatial porosity and permeability. This technique facilitates the comprehensive analysis of core data, well data, and seismic survey data, enabling the derivation of a high-precision spatial distribution of reservoir characteristics. Efforts will continue for further improvement on prediction accuracy. 6 refs., 7 figs., 3 tabs.

  6. Improvement of superconducting cylindrical linear induction motor; Chodendo entokeitan ichiji rinia yudo mota no tokusei kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Kikuma, T.; Tomita, M.; Ishiyama, A. [Waseda Univ., Tokyo (Japan)

    1999-11-10

    For the purpose of we examining the effect of characteristics and ac loss under real machine operating environment of the alternating current superconductivity winding for a realization of the superconductive AC machine vessel, cylindrical shortness first linear guiding motor which used NbTi/CuNi superconducting cable for the primary winding was produced experimentally. The coil number was increased from 6 in 14 this time, and the optimization of the primary current was done, and the improvement on characteristics was attempted. Here, starting torque characteristics, quenching detection protection control circuit are reported. (NEDO)

  7. Aerodynamic characteristics of hypersonic flight experiment (HYFLEX) vehicle; Goku choonsoku hiko jikkenki (HYFLEX) no kuriki tokusei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Hypersonic Flight Experiment (HYFLEX) vehicle successfully performed a hypersonic lifting flight. The vehicle was developed to establish the basic technologies necessary for an unmanned shuttle vehicle. In this report, the primary aerodynamic characteristics derived from analysis of the flight data are presented. They are aerodynamic force coefficients, longitudinal trim characteristics, stability and control derivatives, elevon hinge moment coefficient, and surface pressure distribution. The flight results are compared with the preflight predictions based on wind tunnel tests and CFD calculations. The purpose of the comparison is to evaluate the validity of the prediction methods including the development of aerodynamic uncertainties in the vehicle design process. The flight results agreed well with the predictions. This shows that the prediction methods are generally valid for the design of a lifting reentry vehicle with a high angle of attack. On the other hand, some differences between the flight results and the predictions were found in axial force coefficient, elevon trim deflection, and RCS gas-jet interaction. 36 refs., 33 figs., 9 tabs.

  8. Water permeabilities of pulverized fuel ash; Bifuntan sekitanbai no tosui tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ichikawa, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Nagataki, S. [Niigata University, Niigata (Japan); Hosoda, N. [Kumagai Gumi Co. Ltd., Tokyo (Japan); Utsuki, T. [The Coal Mining Research Center, Japan, Tokyo (Japan); Kubo, H. [Obayashi Corp., Tokyo (Japan)

    1996-09-01

    It is intended to establish a technology to utilize coal ash in bulk to deal with its increasing production. In order to expand its use into earth engineering materials, two kinds of combustion ashes produced from dust coal burning power plants were used for studies using different kinds of tests. The tests were carried out on strength properties, water permeability, and characteristics of dissolving trace amounts of chemical constituents, with regard to addition effects of cement into compacted and slurry-state dust coal burned ashes. The derived findings may be summarized as follows: as the strength properties, the strength for both of the compacted and slurry-state ashes increases as the cement addition ratio is increased; growth of the strength due to the cement addition ratio and material age varies depending on the kinds of dust coal burned ash; comparison of strengths of the compacted and the slurry-state ashes indicates the strength of the latter ash is about one-third to quarter of that of the former ash; water permeability of the ashes decreases both in the compacted and slurry- state ashes as the cement addition ratio is increased; and the cement addition ratio gives greater impact to the water permeability than the density of the ashes. 28 figs., 5 tabs.

  9. Characteristics of microtremors in Hanshin area; Hanshin chiiki ni okeru bido no kihon tokusei nitsuite

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Suzuki, K.; Yamanaka, H.; Seo, K. [Tokyo Institute of Technology, Tokyo (Japan)

    1996-10-01

    To increase general understandings of fundamental characteristics of microtremors in Hanshin area, microtremors have been observed at Sumiyoshi River-side, Rokko Island, and Nishinomiya. Relations were discussed among the stability of predominant period, successive fluctuation and meteorological conditions. For the analysis, cosine-type taper was conducted before and after 10% of the observed records, and Fourier spectrum was calculated by smoothing using Parzen window with a band width 0.3 Hz. Geometrical mean of two components was used as a horizontal component. At the observation points except Sumiyoshi River-side, predominance in the short period side was not distinct, and was not stable due to the successive fluctuation of predominant period. However, there was less successive fluctuation of spectrum ratio between different two points in the band with period more than 1 sec. Since there was a close correlation between the successive fluctuation in this band and the wind velocity or air pressure, the microtremors in this band was affected by a single vibration source. Ground characteristics could be illustrated by the averages of ratio against base points of moving observation. 14 refs.

  10. Synthesis and characteristics of antimicrobial sand; Kokinsei suna no gosei to tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Tomoki

    1999-11-01

    It has emphasized insanitary sand pool by the cause in the excretory substance of dog and cat as social problem. Taking this as an opportunity, each school and kindergartens, etc. tackled the pollution abatement of sand pool. Antimicrobe boom by the development of inorganic system antimicrobial agent has already happened before this. Especially, it used the silver inorganic antimicrobial agent in the material field of versatile. Then, the manufacturer of each antimicrobial agent examined the use of antimicrobial agent as a pollution abatement of sand pool. Here, this paper explains pollution present state of sand pool it deprives deprive and manufacturing of the antimicrobe sand and features in respect of the antimicrobe sand. (NEDO)

  11. Solar collecting characteristics of regenerative solar air collector; Chikunetsushiki kuki shunetsuki no shunetsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, H.; Takano, S.; Kamitaira, T. [Hachinohe Institute of Technology, Aomori (Japan)

    1997-11-25

    In order to develop a solar drying equipment for agricultural and marine products, a regenerative solar air collector was fabricated on a trial basis, which uses round stones as a heat storing material. Its heat collecting characteristics were discussed. The air heat collector was installed on a roof of the Hachinohe Engineering University facing due south. The inside of the air heat collector is lined with heat insulating material with a thickness of 30 mm, and black-painted round stones were laid as an heat insulating material on the floor and the north face. The collector is of a natural air circulating system in which outside air enters from an entrance open to atmosphere, and warmed air exits from upper exit. A selectively absorbing face plaque for accelerating the natural circulation was suspended on the upper part of the north face of the collector. An experiment was performed also on a case in which air is forcibly circulated by fan from the air exit hole. In the natural circulation system, high heat collecting efficiency is shown in the forenoon. However, heat loss increases as temperature in the equipment rises, and heat stored in the round stones during daytime was dissipated completely in the afternoon to night. In the case of the forced circulation system, heat collecting efficiency as high as about 90% was shown in sunny days. This is thought because of heat storage buffering action due to storage of heat in and its dissipation from the round stones, and because of suppression of heat dissipation from the glass surface. 1 ref., 9 figs.

  12. Survey on bio-chemical complex harmonized with global environment. 3; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted of bio-chemical complex harmonized with the global environment for the purpose of constructing the material production process harmonized with the environment by the process fusion between biological conversion and chemical reaction. Palm oil was taken up as renewable raw material plant resource. The process utilizing bio-chemical reaction advances at normal temperature and pressure and is high in reaction specificity and selectivity. This is a recycling, circulation and environmental harmony type production technology which brings high yield, energy conservation, resource conservation, and low environmental loads. Waste water treatment and production of useful substances from sludge were thought as elementary technology. A possibility was studied of enzyme production by culturing solid waste, and the enzyme was applied to the hydrolysis process. The paper indicated trace components in the palm oil and the extraction method and proposed the production process of new derivatives for adding value to hydrolysate. A study was also made of the overall process flow which integrated these new processes and the material balance. The comprehensive evaluation of this new process was made from the aspect of the product structure, the market, construction cost, economical efficiency, and the environment. 133 refs., 65 figs., 56 tabs.

  13. Survey on bio-chemical complex harmonized with global environment. 2; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The technical background was investigated for the purpose of making an effective use of the environmentally harmonized type production process and biomass resource, and the concept was indicated of a biochemical complex using vegetable fat and oil as a raw material. The vegetable fat and oil used were mainly palm oil and coconut oil. As to the production of commodity chemicals from palm oil, investigations were made on the outlook of the production amount and the composition of fat and oil, and a study was made on a possibility of substituting palm oil for beef fallow as a raw material of fatty acid. Relating to a large amount of the waste of biomass left after collecting the useful part of plants with fat and oil, a process was studied and proposed of producing useful enzymes by the solid culture method in which the biomass waste was used as a raw material. The enzymes produced here were made to be used for conversion of fat and oil and production of bioplastics, etc. Also, as to the plastics produced by microorganism, results of the recent research were examined on fungus bodies and the culture medium, bioreactors, separation and refining after producing fungus bodies, physical properties of the plastics, etc. 178 refs., 77 figs., 68 tabs.

  14. Measurement of organic carbon quantity at chemoautorophic bacterium; Kagaku dokuritsu eiyo saikin ni okeru yuki tansoryo no sokutei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tsuda, I.; Kato, K.; Nozaki, K. [Electrotechnical Laboratory, Tsukuba (Japan); Kurokawa, K. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-27

    Described herein is the method for analyzing quantity of organic carbon synthesized by chemoautotrophic bacterium. It is based on the combustion-infrared spectroscopy, which is normally adopted for quantitative analysis of organic carbon. The problems involved in the measurement of organic compounds synthesized by iron-oxidizing bacteria are noise by culture medium components, aging of gas analyzer and contamination with organic compounds from a silicon plug. The measures taken in this study against these problems include comparison of the results with a medium containing iron-oxidizing bacteria with those with a medium free of these bacteria, calibration with the standard solution for each measurement, and replacement of a silicone plug by a silicon cap. Organic carbon is measured by a TOC-5000 analyzer equipped with an automatic sample feeder ASI-5000. Biomass density is determined by the MPN method. It is confirmed that organic carbon quantity is almost in proportion to biomass density, a phenomenon which can be used to determine organic carbon quantity. 7 refs., 6 figs., 1 tab.

  15. Geoelectrical structure by electrical logs and Schlumberger sounding at the Akinomiya geothermal field, Akita Prefecture; Denki kenso oyobi Schlumberger ho ni yoru Akinomiya chinetsu chiiki no hiteiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Kajiwara, T.; Takemoto, S.

    1997-05-27

    Based on the electrical logging data of the existed well and Schlumberger sounding data obtained in 1974, a two-dimensional inversion analysis of the specific resistance profile was conducted at the Akinomiya geothermal field, Akita Prefecture. From the electrical logging data, relationships between the geology and the specific resistance were illustrated. The specific resistance values of basement rocks showed more than 100 ohm-m, which were higher than those of the other seams. Intrusive rocks and tuffs in the basement rocks showed locally low values less than 100 ohm-m. Younger volcanic rocks showed low values around 10 ohm-m. As a result of the two-dimensional inversion analysis, the basement rocks could be detected as high specific resistance layers. Accordingly, it was considered that the basement rocks in this field can be detected as high specific resistance layers by analyzing the results of field survey sufficiently. Low specific resistance zones were observed in the shallow depth, which corresponded to the fumarolic gases. There were some layers with remarkably varied specific resistance values, which were considered to be related with alteration. 6 refs., 3 figs.

  16. Efficient calculation of potential distribution in two-layer earth; Niso kozo daichikei ni okeru denki tansa no tame no koritsuteki den`i keisan shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, M.; Okamoto, Y. [Chiba Institute of Technology, Chiba (Japan); Endo, M.; Noguchi, K. [Waseda University, Tokyo (Japan); Teramachi, Y.; Akabane, H. [University of Industrial Technology, Kanagawa (Japan); Agu, M. [Ibaraki University, Ibaraki (Japan)

    1997-05-27

    An efficient calculation method of potential distribution in the presence of an embedded body in multi-layer earth has been proposed by expanding the method of image with a consideration of multiple reflection between the ground surface and each underground boundary. For this method, when solving boundary integral equation with the potential of embedded body surface as only one unknown, i.e., when obtaining discretization equation, ordinary boundary element program developed for analyzing the finite closed region can be used. As an example, numerical calculation was conducted for the two-layer earth. The analysis expression of potential distribution in the case of the certain embedded body in two-layer earth has never published. Accordingly, the calculated results were compared with those by the integral equation method. As a result, it was concluded that the primary potential obtained from the present method agreed well with that obtained from the integral equation method. However, there was a disregarded difference in the secondary potential. For confirming the effectiveness, it was necessary to compare with another numerical calculation method, such as finite element method. 5 refs., 5 figs.

  17. Archaeological prospecting using electrical resistivity method. Case history of Kaibukiyama ancient tomb; Denki tansaho ni yoru iseki tansa. Kaibukiyama kofun no chosarei

    Energy Technology Data Exchange (ETDEWEB)

    Mizunaga, H.; Ushijima, K.; Kishikawa, H. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-05-27

    To grasp the three-dimensional structure of ancient tomb during the archaeological prospecting of Kaibukiyama ancient tomb, various electrical resistivity methods were tried. For the survey, firstly, in order to clarify the electrical resistivity structure of rear circular part of ancient tomb, roughly, mapping was conducted by means of two-electrode method using a multi-channel measuring system. Then, the vertical prospecting was conducted densely with a mesh form having VES intervals of 2 m as a detailed survey by means of Schlumberger method. For the three-dimensional inverse analysis of apparent electrical resistivity data by the two-electrode method, a program with high calculation speed was developed by using algorithm where Jacobian with a homogeneous model is adopted for the Jacobian calculation. As a result of the analysis, an outline of underground 3-D resistivity structure was determined. The resistivity anomaly with high values obtained from the results of 2-D inverse analysis of VES curve by means of Schlumberger method agreed well with the central part of the ancient tomb, which was confirmed during the archaeological survey. 4 refs., 8 figs.

  18. The utility of electrical prospecting about the holocene sediment survey in the Mekong delta area; Mekon deruta chiiki no kanshisei taisekibutsu chosa ni okeru denki tansa no yuyosei

    Energy Technology Data Exchange (ETDEWEB)

    Quang, T.D.; Yamauchi, Seiki [Shimane University, Shimane (Japan); Iwata, Akio; Sato, Tsutomu; Saito, Takeshi; Nagira, Yukihiro

    1999-02-01

    The Mekong river is a countable big river in the world, originated from Tibet area of China (an elevation of 4,700 m) and flowing across Burma, Laos, Thailand, Cambodia and Vietnam and its total length is 4,200 m. In the passed 70 years, the survey and research on the Mekong delta area has been carried out in wide fields including geology, geomorphology, hydrology, agronomy and sociology by many researchers from France, America and Vietnam. It could be said that the details on the wide delta formation and deposit would be surveyed and studied from now on. In the Mekong delta area at the lower reaches of the Mekong river, the surface water was seriously polluted, the water supply would be a problem in order to supply a clean water to local residents. For this reason, the underground water survey was carried out, and hydrologic and geological situation has been clarified step by step. It was necessary to carry out the detailed underground water survey since this area is wide and the detailed data were few in the past. This time, the results were reported on the electrical prospecting for the Holocene sediment survey in the upper reaches of the Mekong river. (translated by NEDO)

  19. Conductivity Measurements of Alkali Metal Thiocyanates in Water-Methanol Mixtures; Mizu-metanoru kongoyoubai ni okeru arukari kinzoku chioshiansan`en no denki dendodo sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, Eiji.; Horimoto, Sanaki. [Shinshu University, Nagano (Japan). Faculty of Science

    1999-03-10

    The counductivity of several alkali nmetal thiocyanates in water-methanol mixtures was measured at 25degreeC. the data were analyzed using Lee-Wheaton theory for symmetrical electroyers to cbtain ion association constant, K{sub A}, limiting molar sonductivity, {Lambda}{sub 0}, and limiting ionic molar conductivity, lamnda{sub 0}{+-}. In all the solvent systems, calculated{lambda}{sub 0}{sup +} values of the alkali metal ions increase in the order L{sub i}{sup +}

  20. High temperature electrical conductivity of yttrium sesquioxide under entremely low oxygen pressure; Gokuteion sansoatsuka ni okeru ittoria no koon denki dendosei

    Energy Technology Data Exchange (ETDEWEB)

    Yoneoka, T.; Terai, T. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Takahashi, Y. [Chuo University, Tokyo (Japan)

    1996-01-20

    Yttrium sesquioxide (yttria) is considered to be one of the most hopeful candidate materials for a collector electrode of the separated uranium atom in a laser uranium enrichment system. In order to confirm a required property for the electrode, the conductivity measurement of yttria was performed under a simulated condition in the presence of molten uranium. Because of the extremely low oxygen pressure in the U-UO2 system such a condition was locally realized by placing yttria specimens between plates of titanium or vanadium at high temperature. The specimens were reduced in advance to hypostoichiometry with titanium or vanadium plates under the condition of 1600 K and 2.5 Ms in vacuo. The electrical conductivity measurement was performed by the AC four-probe method in the temperature range of about 900-1600 K and the frequency range of 60 Hz-30 kHz. The electrical conductivity of hypostoichiometric yttria reduced by titanium was higher than that of intrinsic germanium at room temperature (2.1 S/m). This specimen showed the characteristic behavior in the temperature dependence of conductivity; the conductivity showed semiconductor-like behavior in the range of 1400-1600 K, while it had a minimum at about 1250 K and again increased below this temperature. That of hypostoichiometric yttria reduced by vanadium was much lower than that of the specimen, educed with titanium and followed a straight line in the Arrhenius plot above 1000 K. The conductivities of both hypostoichiometric specimens were independent of frequency, which means the conduction carrier was the electron or electron hole. From the oxygen concentration of the metals which were used for the reduction, the oxygen pressures equilibrated with the yttria specimens here estimated to discuss the relation to the measured conductivities. 19 refs., 8 figs., 1 tab.

  1. Charging and discharging time control of electric vehicles for the purpose of load leveling; Fuka heijunka wo mokuteki to suru denki jidosha no juhoden jikan seigyo hosaku

    Energy Technology Data Exchange (ETDEWEB)

    Koyanagi, F.; Uriu, Y. [Seikei University, Tokyo (Japan)

    1998-05-01

    By ZEV regulation of the California government in 1990, not only the United States but also European countries and Japan are largely interested in replacing gasoline car by electric vehicle. Electric utilities expect that the electric vehicle improves the difference between the daytime and nighttime of a recent demand as a new market of electric power demand. There are some reports that indicates on the danger which generates the new peaks as the electric vehicles spread through the market in charging start hour. As the countermeasure for avoiding this problem, the authors propose that 1) inverse load flow by discharging of the contract private use EV is carried out as an energy shift in daytime, 2) the regional charging time shift method is introduced in the midnight charging time zone, in this paper. Therefore, the energy actual consumption of the automobile was investigated, and future demand was predicted by the mathematical consumption modeling. Especially, it is described a strategy of optimum introduction on scheme of effective electric vehicle for energy shift in section 2.2. And authors point out the necessity of market regulation for EV. 14 refs., 10 figs., 1 tab.

  2. Influence of cross-anisotropy material behavior on back-calculation analysis of multi-layered systems

    CSIR Research Space (South Africa)

    Maina, JW

    2008-07-01

    Full Text Available 2008 27 INFLUENCE OF CROSS-ANISOTROPY MATERIAL BEHAVIOR ON BACK-CALCULATION ANALYSIS OF MULTI-LAYERED SYSTEMS Yoshiaki OZAWA Department of Civil and Environmental Engineering, Tokyo Denki University Ishizaka, Hatoyama Town, Hiki-gun, Saitama... and Environmental Engineering, Tokyo Denki University Ishizaka, Hatoyama Town, Hiki-gun, Saitama 350-0394, Japan matsui@g.dendai.ac.jp ABSTRACT Each layer in a pavement structure is compacted during construction. Moreover, since the compaction process...

  3. Desulfurization and oxidation behavior of ultra-fine CaO particles prepared from brown coal; Kattan wo mochiite choseishita CaO chobiryushi no datsuryu tokusei to sanka tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin, G.; Roman, M.; Yamazaki, Y.; Abe, H.; Harano, Y.; Takarada, Y. [Gunma University, Gunma (Japan). Faculty of Engineering

    1996-10-28

    The effect of reaction temperature and oxygen concentration on the desulfurization and oxidation behavior of ion-exchanged brown coal by Ca as new desulfurizing agent was studied. In experiment, Yallourn coal was used for ion- exchange, and limestone produced in Tochigi prefecture was also used for comparative study. Ca-exchanged brown coal was prepared by agitating coal in Ca(OH)2 slurry for 24 hours. The desulfurization behavior of a desulfurizing agent was obtained by measuring H2S and sulfur compounds in outlet gas of a reactor, and the oxidation behavior by measuring SO2 emission in outlet gas after oxidation reaction. As the experimental result, CaO produced from Ca-exchanged brown coal offered the extremely high activity to desulfurization reaction in a temperature range of 850-950{degree}C as compared with limestone. Although the oxidation behavior was dependent on oxidation temperature and oxygen concentration, CaS obtained from Ca-exchanged brown coal was more rapidly converted to CaSO4 than limestone. 3 refs., 8 figs., 2 tabs.

  4. Properties of fiber reinforced plastic rods for prestressing tendons of concrete. 8. ; Dynamic fatigue behavior of reinforced plastics rods. Prestressed concrete yo FRP kinchozai no tokusei. 8. ; FRP rod no doteki hiro tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Uomoto, T.; Nishimura, T. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1994-01-01

    This paper describes the result of experiments on dynamic fatigue and creep characteristics of plastic rods reinforced by aramid, glass and carbon fibers (AFRP rods, GFRP rods, and CFRP rods) used as prestressing tendons of concrete. Although the dynamic fatigue limit for generally used FRP rods is not known, the fatigue strength was found to decrease in the order of AFRP rod > CFRP rod > GFRP rod. However, AFRP rods have shown a sharp decrease in the fatigue strength starting from around one million dynamic loading iterations. The AFRP and GFRP rods have had creep fracture existed in fatigue fracture at a high stress of 100 kg/mm[sup 2] or higher, and fatigue fracture existed due to dynamic fatigue below that stress. Residual tensile strength after fatigue due to two-million iterative loadings was about 83% of the average tensile strength for the AFRP rods, and about 69% for the GFRP rods, whereas that for CFRP rods was about the same as the average strength. 8 refs., 6 figs., 1 tab.

  5. Accuracy of parameters of permeable fractures by hydrophone VSP; Hydrophone VSP ni yoru tosuisei kiretsu no tokusei hyoka no seido

    Energy Technology Data Exchange (ETDEWEB)

    Kiguchi, T.; Ito, H.; Kuwahara, Y.; Miyazaki, T. [Geological Survey of Japan, Tsukuba (Japan); Yabuuchi, S.; Hasegawa, K. [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

    1997-10-22

    Hydrophone VSP (vertical seismic profiling) experiment is under way as a technique for detecting subsurface water-permeable cracks by use of boreholes and for evaluating their characteristics (permeability index, crack direction, dip angle). In this report, tube waves observed by hydrophone VSP are subjected to analysis for the determination of water-permeable crack characteristics, the impact caused by errors in the value inputted for analysis is estimated, and a model calculation is performed in case there is no agreement between data from the borehole and data from VSP, all for examining the VSP records for accuracy. When an error rate of 15% is given to the tube wave/P-wave amplitude ratio, a change of 40% or lower results in the permeability index, and a change of 10deg or less in the dip angle, which means that an error in the amplitude ratio does not affect the analysis very much. Changes in the amplitude ratio resulting from changes in crack direction and dip angle differ, dependent on the offset rate. When angular differences among plural crack directions are within 90deg and dip angles within 60deg, the result of analysis represents the average characteristics of the plural cracks. 7 refs., 5 figs., 2 tabs.

  6. Hydrogenolysis reactions characteristics of deashed coal under low temperature; Teionka ni okeru dakkai shoritan no suisoka bunkai hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Owada, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    In relation to coal liquefaction, the effect of inorganic minerals on liquefaction reactivity and the effect of hydrofluoric acid (HF) treatment on organic molecular structure of coals were studied by demineralization of low-rank coals in HCl or HF solution. In experiment, Taiheiyo coal specimen was deashed in HCl solution at 25-70{degree}C for 6 hours while agitating, and in addition, deashed in HF solution. Hydrogenolysis of the deashed coal specimen was conducted using tetralin or methylnaphthalene as solvent under initial hydrogen pressure of 1.96MPa at reaction temperature of 693K for 60min. The experimental results are as follows. The ash content of Taiheiyo coal hardly offers catalysis in hydrogenolysis reaction. Carboxyl group increases in demineralization of coal because of breakage of bridged bonds. Organic structure of coal changes by demineralization in dense HF solution. Change in organic structure of coal by demineralization in dense HF solution is dependent on treatment temperature. 2 refs., 4 figs., 1 tab.

  7. Studies on characteristics of fluid dynamics in the coal liquefaction reactor; Sekitan ekika hanno tonai no ryudo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sakawaki, K.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Tachikawa, N.; Moki, T.; Ishikawa, I. [Japan Atomic Energy Research Institute, Tokyo (Japan)

    1996-10-28

    To design the coal liquefaction reactor of large scale plant in future, it is important to understand characteristics of fluid dynamics within the coal liquefaction reactor. In this study, to measure the fluid dynamics of liquid phase within the coal liquefaction reactor operated under high temperature and high pressure coal liquefaction condition, neutron attenuating tracer (NAT) technique, one of the tracer test methods, was applied using 1 t/d coal treating PSU. The residence time of liquid phase within the reactor can be measured by utilizing property of neutron of being absorbed by materials. The tracer was injected at the inlets of first and third reactors, and the neutron was counted at each outlet. The concentration of tracer was derived from the discrete value, to determine the residence time distribution of liquid phase. The mean residence time of liquid phase in the single first reactor and in the total three reactors were prolonged under the severe operation conditions of liquefaction. The more severe the liquefaction operation condition was, the more active the mixing of liquid phase was in the first reactor. It was found that the progress of reaction was accelerated. 2 refs., 5 figs., 1 tab.

  8. Prediction of blast vibration level considered propagation characteristics; Denpa tokusei to koryoshita happa shindo level no yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Kunimatsu, S.; Jinguji, M. [National Institute for Resources and Environment, Tsukuba (Japan); Yamada, M.; Hirai, T. [Newjec Inc., Osaka (Japan); Durucan, S.; Farsangi, M.

    1997-10-22

    With an objective to assess environmental influence induced by blast vibration, a study has been carried out on a method to predict vibration levels. The study has discussed a method to calculate vibration levels, in which vibration propagating characteristics are sought on blast vibration generated from an open-cut limestone mine from acceleration waveforms in the vicinity of the blast source and residential housings by using an octave analysis, and waveforms are predicted. The shortest straight line distance from the blast position to a housing is about 150 m, and the height difference is about 30 to 40 meters. The measuring instruments include a vibration level meter used for pollution measurement and a data recorder, with signals lower than 1 Hz and higher than 90 Hz being interrupted. The environmental influence assessment discusses not only the maximum value of the vibration level, but also sizes of values of each band by using a frequency analysis. The result of the discussions revealed that the prediction of the vibration levels is little affected by phase characteristics, and that no problems are caused in the measurement accuracy even if the vibration levels are predicted by using relative decay amount according to a one-third octave analysis for the propagation characteristics. 5 figs., 4 tabs.

  9. Predict optimize the friction characteristics of brake pads; Brake pad no masatsu tokusei no yosoku to saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Saotome, H. [Nissin Kogyo Co., Tokyo (Japan); Kato, T. [The University of Tokyo, Tokyo (Japan)

    1997-10-01

    The effect of the friction and the wear properties of brake pads were experimentally studied using a test rig of scale of 1/10 of the system used in a commercial car. The experimental data were investigated by the Multiple Regression Analysis and the Neural Network, and the effects of volume % of components on the friction and the wear properties were predicted. In addition the components of brake pads are optimized by Genetic Algorithms. 8 refs., 9 figs., 4 tabs.

  10. Improvement of superconducting cylindrical linear induction motor; Chodendo entogata tan'ichiji rinia yudo mota no tokusei kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Kikuma, T.; Ishiyama, A. [Waseda Univ., Tokyo (Japan)

    2000-05-29

    For the purpose of examining the characteristics (effect of stability and ac loss by the higher harmonic wave etc.) of an alternating current superconductivity winding under a real machine operating environment of the super-conductive AC machine vessel, authors produced a cylindrical shortness first linear guiding motor (SCLIM) which used the NbTi/CuNi super-conducting cable for the first excitation winding experimentally. In this study, the evaluation of the start up thrust and operation confirmation of the quenching detection protection circuit were carried out using the produced SCLIM. In the quenching detection protection control circuit, the first excitation winding was divided into an internal layer and an outer layer, and both layers were excited in the 2 layer division and a quenching detection protection circuit was installed on the 2 layers respectively. The circuit of a part of fact by this of the phase in which the quench was generated and observed was cut off, and the operation would be able to be continued in part of the remainder of the phase and other two phases. Here, it is to cut off the quenched phase from the circuit, when the phase current becomes zero, and the other effect on the phase is held as small as possible. (NEDO)

  11. Characterization of kaolinite coated with silicone by low-temperature plasma. Teion plasma de silicone coating shita kaorin no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Suhara, T.; Fukui, H.; Nakano, M.; Yamaguchi, M. (Shiseido BAsic Research Laboratories, Yokohama (Japan))

    1991-06-20

    Any pigment is used as a mixture with other components, and the dispersibility and the catalytic activity affecting the decomposition and oxidation of other components are the very important characteristics. The surface treatment or modification is carried out to improve them. In this paper, the surface of kaolinite was treated by irradiation of low-temperature plasma to a mixture of hexamethylcyclotrisiloxane(D{sub 3}) and kaolinite under atmospheric pressure of nitrogen to study the structure, physical properties and catalytic activity. The treated kaolinite surface changed to hydrophobic and had the effect to suppress the linalool decomposition. It could be estimated from these results that a large part of kaolinite surface would be covered by silicone film. It was verified that the silicone film was stable to solvents such as chloroform and also stable to high temperature. It was confirmed that a part of the structure of silicone film was composed of polymer of straight chains and cyclic chains, and other part of that was made of bridged network structure. 20 refs., 9 figs., 3 tabs.

  12. Geological structure of Osaka basin and characteristic distributions of structural damage caused by earthquake; Osaka bonchi kozo to shingai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, K.; Shiono, K.; Inoue, N.; Senda, S. [Osaka City University, Osaka (JP. Faculty of Science); Ryoki, K. [Osaka Polytechnic Collage, Osaka (Japan); Shichi, R. [Nagoya University, Nagoya (Japan). Faculty of Science

    1996-05-01

    The paper investigates relations between the damage caused by the Hyogo-ken Nanbu earthquake and the deep underground structures. A characteristic of the earthquake damage distribution is that the damage concentrated near faults. Most of the damages were seen on the side of faults` relatively falling rather than right above the faults and of their slightly slanting to the seaside. Distribution like this seems to be closely related to underground structures. Therefore, a distribution map of the depth of basement granite in Osaka sedimentary basin was drawn, referring to the data on basement rock depth obtained from the distribution map of gravity anomaly and the result of the survey using the air gun reflection method. Moreover, cubic underground structures were determined by 3-D gravity analysis. The result was concluded as follows: when observing the M7 zone of the low land, in particular, where the damage was great from an aspect of gravity anomaly, the basement rock below the zone declined near the cliff toward the sea, which indicates a great possibility of its being a fault. There is a high possibility that the zone suffered mostly from the damage caused by focusing by refraction and total reflection of seismic wave rays. 3 refs., 8 figs.

  13. Characteristics of UHF radio wave propagation in an underground gallery. Chika kodo wo tsutawaru goku chotanpa (UHF) no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, T.; Isei, T. (National Research Inst. for Pollution and Resources., Tsukuba, (Japan))

    1990-03-25

    UHF radio wave propagation along underground galleries is formulated using two methods so far proposed by other authors; one is based on characteristic equations and the other one makes use of simple geometrical image sources. Experimental measurements are carried out on the propagation of UHF waves of frequency 100 - 1500 MHz sent along two underground galleries; one of reinforced concrete wall and the other one of wooden timbering, the length being 400m or 200m and the area of cross section being 5.4 or 3.8 square meter respectively. It is demonstracted that the characteristics of wave propagation calculated by means of the geometrical image source method are in better agreement with the result obtained by the measurement compared with those by the characteristic equation method. Furthermore, numerical analysis using the geometrical image source method gives the following results; as the frequency of wave is increased, the attenuation constant of the wave propagating along an underground gallery decreases, becomes almost independent on the area of cross section of the gallery and insensitive to the kind of timbering materials. 5 refs., 11 figs.

  14. Influence of angle of inclination on power of solar module; Taiyo denchi module no keisha kakudo to shutsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K.; Nishitani, M. [Dai Ichi University, College of Technology, Kagoshima (Japan)

    1997-11-25

    Experiment/study were conducted on the influence of angle of inclination on output of solar modules. In the experiment, changing the angle of inclination of the photovoltaic module installed on the top of school building to 0, 30, 60 and 90 degC, the global radiation on an inclined surface was measured by pyranometer equipped with the module, and at the same time output characteristics were measured by I-V curve tracer. In the I-V curve tracer, voltage, current, and output capability diagram are illustrated automatically changing bias voltage to get the maximum output. The global radiation on an inclined surface and the maximum output indicated an almost proportional relation and were expressed in a recursion method. Moreover, measurement of the global radiation is usually conducted using the amount of global radiation on a horizontal surface, and the global radiation on an inclined surface is calculated as a sum of the direct solar radiation amount and the sky solar radiation amount after determining a penetration rate by the relational equation. By calculating the global radiation on an inclined surface, it becomes possible to calculate the maximum output of photovoltaic modules by this recursion method. 1 ref., 6 figs., 1 tab.

  15. Output characteristics of torsion arc blade type horizontal axis windmill; Nejire enko yokugata suiheijiku fusha no shutsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, N.; Kishimura, K. [Meiji University, Tokyo (Japan)

    1997-11-25

    The previous paper theoretically analyzes characteristics of a torsion arc blade type (TABT) horizontal axis windmill to derive the theoretical equations, which give the results in good agreement with the observed ones, when multiplied by a blade shape factor. This paper discusses that the theoretical and observed results are in good agreement with each other by taking into consideration shape-related solidity and number of blades. The following findings are obtained, when parameters related to a 6-blade TABT horizontal axis wind mill are introduced and hysteresis brake is used as the load resistance for torque measurement. Shape factor can be represented by two factors of blade number and solidity. The same equation for shape factor is applicable to both elliptical and rectangular blades. These blades need different theoretical equations to give the results in agreement with the observed ones, when operated at a tip speed ratio (TSR) of 1.77 and 1.58, respectively. Rotational force is affected by the rear blade shape when they are operated at a respective TSR below the above level, but unaffected at beyond the above level. 5 refs., 9 figs., 1 tab.

  16. Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-10

    Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

  17. Leveling of battery load and extension of battery life by serial connection of electric double layer capacitors with batteries for electric vehicles. Experimental results on the small model; Denki jidoshayo denchi to denki nijuso capacitor no chokuretsu setsuzoku ni yoru denchi futan no heijunka oyobi denchijumyo no enshinka. (kogata model ni yoru jikken seika). Kogata model ni yoru jikken seika

    Energy Technology Data Exchange (ETDEWEB)

    Takehara, J.; Okubo, N.; Miyaoka, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1996-10-25

    The load leveling method of batteries for electric vehicles was studied for extension of a battery life and mileage every charging. Under large load fluctuation conditions such as deceleration and acceleration, use of electric power sources other than battery for peek load at acceleration can improve a battery life, output power capacity and mileage every charging. Combination of effective recovery of regenerative power at deceleration with its discharge at acceleration is one of the effective methods. The electric double layer capacitors are serially connected with the batteries, regenerative power is charged only into the capacitors, and both voltages of the battery and capacitor are applied to a power circuit. Battery load is reduced by load on the capacitor. Until the capacitor is re-charged by regenerative power after full discharge, power is supplied only by battery through a diode. Capacitor power is used as effectively as possible until approaching considerably low voltage. As peak load of the battery is reduced by 30%, the mileage increases by 5.7%, and the battery cycle life becomes 1.5 times longer. 7 refs., 5 figs., 3 tabs.

  18. FY 1999 report on the results of the technology development of next-generation chemical process; 1999 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the naphtha catalytic cracking, selective oxidation reaction of saturated hydrocarbon, new reaction mechanism utilization process, etc., as next-generation chemical process technology in FY 1999, and the results were summarized. As to the technology of naphtha catalytic cracking, developed was La203/p/ZMS-5 zeolite catalyst which is high in cracking activity and high in light-olefin selectivity. By the FS, it was confirmed that this is more excellent in case of the fixed bed reactor than in the present process. Concerning the technology of selective oxidation reaction of saturated hydrocarbon, the basic information/knowledge were obtained about the construction of catalytic principle toward the high selective catalytic partial oxidation, elucidation of a reaction mechanism in alkane oxidation and design of high functional catalysts, elucidation of a mechanism in butan oxidation, synthesis of alkane selective oxidation catalysts, etc. In relation to the technology of new reaction mechanism utilization process, the following were carried out: study of ethyl benzene dehydrogenation using the membrane reactor trially fabricated in the previous fiscal year, development of high efficiency hydrogen penetration membranes and low temperature high activity catalysts, study of the new process by membrane reactor. (NEDO)

  19. Proceedings of the papers of the 33rd Coal Science Conference (1996); Dai 33 kai sekitan kagaku kaigi happyo ronbunshu (1996)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-28

    This is a proceedings of the papers made public in the 33rd (fiscal 1996) Coal Science Conference held by the Japan Institute of Energy. The number of the papers included is 82. The processes such as coal liquefaction, coal gasification and pyrolysis are largely influenced by reaction of the carbon compound in coal. However, coal, which is different in reaction characteristics depending on its producing area, is a comprehensive compound. Therefore, the trial has been made for clarifying the molecular structure and skeleton. In the sense, the following papers are taken notice of: Suzuki and others` Estimation for origin of coals by biomaker analysis; Sugimoto and others` Change of unit skeletons during the artificial coalification; Hirado and others` Study on the correlation between chemical and mineral composition of coal ashes; Okawa and others` Coal structure construction system with construction knowledge and partial energy evaluation; Kanbayashi and others` Analysis of the relationship between coal properties and liquefaction characteristics by using the coal database.

  20. Chemical system integrated on micro-chip. Effects expected for liquid phase micro-space; Maikuro chippu ni shusekikashita kagaku shisutemu. ekiso bisho kukan ni kitaisuru koka toha?

    Energy Technology Data Exchange (ETDEWEB)

    hisamoto, H.; Kitamori, T. [The Univ. of Tokyo, Tokyo (Japan)

    2000-11-01

    Integrated chemical system is a system that integrates units required for transportation, reaction, separation, analysis, which are important for chemical experiment, on a glass substrate in a similar way as semiconductor device. Among it, a system to integrate analysis system is called , and is attracting worldwide attention for DNA electrophoresis analysis. Integrated chemical system has merits such as reduction in waste and high speed reaction, which can be expected from micronization, as well as short molecular diffusion distance, large relative interface surface, and small heat capacity, which are large advantages for high-efficient chemical reaction. The authors, with paying attention this technology, have realized analysis devices such as gene diagnosis, cancer immunity analysis, and environmental analysis, which are difficult by conventional analyzers. On the other hand, this technology is hopeful for organic synthesis and is expected as a technology to invite a large renovation in the chemical technology in the 21st century. (NEDO)

  1. FY 2000 report on the results of the development of the next generation chemical process technology; 2000 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the next generation chemical process by which no energy losses are produced and the amount of the waste is made extremely small by the new catalytic reaction, the reaction using next generation separation/reaction membrane, etc., and the FY 2000 results were summed up. As to the development of the selective oxidation technology of saturated hydrocarbon, the basic knowledge/information were obtained on the following: construction of the catalytic principle toward the highly selective catalytic partial oxidation, elucidation of the reaction mechanism in alkane oxidation and design of the high functional catalyst, functional design in butane oxidation, characterization of the alkane oxidation catalyst and the application to the catalytic development, synthesis of the alkane selective oxidation catalyst, etc. Relating to the development of the process technology using the new reaction mechanism, a target value of equilibrium conversion of 10% or more was achieved using membrane reactor in the dehydrogenation of ethyl benzene. Further, as to the high performance selective membrane and low temperature active catalyst that are indispensable to the element technology, the continuous study was made, and at the same time themes in this study were arranged. (NEDO)

  2. Achievement report for fiscal 1998. Development of next-generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches are conducted on the development of a technology of catalytic cracking of naphtha, technology relative to selective oxidation reaction of saturated hydrocarbons, process technology utilizing solid-phase reaction field, and a process technology utilizing novel reaction mechanism. Also, a survey is conducted on chemical processes of the next generation. Concerning the catalytic cracking of naphtha, reaction systems are roughly divided into two groups by whether or not they proceed in the presence of oxygen. As for rare earth oxide catalyst systems and zeolitic catalyst systems, their performance is confirmed and their reaction mechanisms are estimated. Concerning the selective oxidation reaction of hydrocarbons, studies are made to enhance the performance of catalytic systems that have been selected in researches conducted in the past. Concerning the process of solid phase reaction field utilization, the project is summarized and a concept is constructed of 'solid phase catalyst.' Concerning novel reaction mechanism utilizing process technologies, development is discussed of a novel process using membrane reactor, a highly functional hydrogen permeable membrane, a low-temperature dehydrogenation catalyst, etc., and a dehydrogenation membrane reactor is experimentally built. (NEDO)

  3. Survey report on an environmental harmony type production system of chemical products; Kankyo chowagata kagaku seihin seizo system ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As part of establishing an environmental harmony type production system of chemical products, study and survey were made on PET bottles. Using the life cycle analysis method (LCA), a study was made for proposing a material recycle (MR) method which is environmentally and economically excellent in the stage of recycling waste PET bottles. The total cost of recycling can be reduced by 34% supported by a decrease in equipment cost and improvement in yield if there is no mixture of foreign substances such as aluminum caps and PVC bottles. However, the ratio of the amount obtained from the reduction to the total production cost is small, and it is necessary to take measures from a viewpoint of the cost in a total production process and environmental loads. In a survey in Kawaguchi city, PET bottles discharged from the business sector occupied 41% of all the discharge amount. In a survey in Yokohama city, very important data were obtained on PET bottles appointed as the second type under the recycle law. The quality of PET bottles to be brought to the recycling plant is important for effectively processing PET bottles in MR method. For achievement of MR which is low in cost and small in environmental load, needed were cooperation by citizens, the shipping management system in autonomous government, and changes in design and material quality to be made by the industrial circle. 8 refs., 64 figs., 68 tabs.

  4. Safety (management and technology). Reality of anti-earthquake measures in chemical plants; Anzen (manejimento to tekunoroji). Kagaku kojo no jishin taisaku no jissai

    Energy Technology Data Exchange (ETDEWEB)

    Wataya, I. [Asahi Chemical Industry Co. Ltd., Osaka (Japan)

    1994-08-05

    In Japan where there have been occurring many earthquakes, anti-earthquake measures is one of important things that corporations should take as risk management. In particular, in the chemical industry where a large amount of combustible materials, toxic materials and high-pressure gases are used which has high potential hazard, it is its social responsibility to prevent leakage, fires and explosions of those materials due to earthquakes, and to take in advance measures for minimizing damages if they happen. This paper introduces, as actual anti-earthquake measures, mainly the anti-earthquake measures for facilities and equipment and the plans of prevention of disasters by earthquake of the Kawasaki Plant of Asahi Kasei Co., Ltd. The points in anti-earthquake design are to determine design idea and anti-earthquake design standards based on the investigations into the locational conditions of plants, the evaluation of plant safety and estimation of damage at the time of earthquake; and to adopt a fail safe mechanism for operating a plant on the safe side in the event of earthquake in its design. 2 refs., 1 fig.

  5. Environmental endocrine disruptors and developmental abnormalities in wildlife; Kankyo horumon (gaiinsei naibunpi kakuran kagaku busshitsu) no kankyo seibutsu ni taisuru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Iguchi, T. [Yokohama City Univ., Yokohama (Japan)

    1998-04-15

    The environmental endocrine disruptor, or the so-called environmental hormone, is outlined. Hormones are secreted from endocrine glands in trace amounts, transported by blood, and exert influence on the target organs and distal cells, this to sustain constancy in living organisms. There are two types: peptide hormones which are rows of amino acids and steroid hormones which are composed of cholesterol. Endocrine disruptors are chemical substances discharged into the environment which, once taken into human organisms, disrupt endocrine systems, some acting like female sex hormones and others resisting male sex hormones. Many a wild animal are found affected by them. They are accumulating in human organisms too. Synthesized chemical substances such as DDT, PCB, dioxins, and alkylphenols present in the water system affect a fish by disrupting its endocrine, immunity, nerve, growth, and regeneration. Embryos and larvae are quite susceptible, easy to turn abnormal. Voices are high across the world for the study of environmental endocrine disruptors. Introduced in this report are some animal experiments, typical cases of impact on the ecosystem, and systems for detecting environmental endocrine disruptors. 36 refs., 1 tab.

  6. Survey report for fiscal 2000. Survey on lifelong education system for chemical engineers; 2000 nendo chosa hokokusho. Kagaku gijutsusha shogai kyoiku system chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to identify social needs for continuous education of chemical engineers, a questionnaire survey was performed on member corporations and research institutes in chemical industries. The result of the survey revealed that, among the 1,032 replies, about 60% of the corporations are conducting the continuous education systematically, and 73% is planning to continue it into the future. With regard to its implementation, about 70% of them use the combination of in-house and outside educational organizations, while in using the outside organizations, expectation toward academic societies is as overwhelmingly high as about 60%. Themes of the seminars include the 'latest waste water treatment', 'latest air pollution preventing technologies', and 'latest industrial wastes recovery and treatment technologies' occupying the top three ranks, followed by the 'safety evaluation' and 'safe design' indicating high interest in environment and safety. For engineer ethics, planning and personnel departments showed as high interest as about 80% or higher, but it is about 60% in manufacturing departments. It was revealed that academic societies in Europe and America are paying efforts in the continuous education of member engineers, which, in turn, contribute to financial bases of the academic societies. (NEDO)

  7. Chemistry for preserving the global environment. Part 5. Offensive odor; its present condition and control technique; Kankyo sozai no kagaku. 5. Akushu no genjo to taisaku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Saiki, Y.

    1996-07-01

    Offensive odor substances belongs to a quite different field from the perfume inspire of the same sense of smell, and is a substance forming a lot of troubles which is formed in intimate resident environments such as manufacturing factories of the chemicals, incineration and decomposition treatment process of living body relating substances, stock raising facilities, restaurants and others. A material called the offensive odor substance is generally in very low concentration in the atmosphere, most of which is ppm order in its detection limit. And, the offensive odor intensity is proportional to logarithm of its concentration. For example, even removing 99.9% of the offensive odor substance from its forming source, there is remained its difficult countermeasuring problem of no removing as its offensive odor. At present, the offensive odor is severely regulated by means of laws and acts, research on its relating field is active, and its relating publications have become plenty. In this paper, outline on recent state of the offensive odor and its measuring technique was summarized. 14 refs., 6 figs., 8 tabs.

  8. Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

  9. Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

  10. FY1998 report on the surveys and studies on developing next generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For further resource and energy conservation and environmental load reduction, development is necessary on innovative chemical reaction technologies. This paper describes surveys on next generation chemical processes. As non-halogen processes subject to development of new catalysts, new processes were investigated and searching experiments and discussions were given on isocyanate, propylene oxide, and phenol. Technological progress in the C1 chemistry was investigated. Problems in hydrocarbon compound oxidation, hydroxylation, and decomposition by utilizing microorganisms were put into order as application of environmentally friendly technologies. Marine biotechnical possibilities were surveyed. The surveys were given on new processes utilizing the phase transfer catalyst forming a third phase, manufacture of biodegradable plastics, and a novel reaction system combined with self-separation process using molecular assembly. Possibilities were searched on designing a truly simple production system of highly energy saving type. Such fundamental common technologies as structure analysis, property control and reaction engineering were investigated for methods to manufacture functional micro-powder chemical materials. Development was discussed on a system for technology assessment over whole product life cycle to structure a technology assessment basis. (NEDO)

  11. Study on recent research trends in the chemical fields; Kagaku bun`ya ni okeru saikin no kenkyu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This research is conducted to search study themes of chemistry expected towards the 21st century. The complex compound in the fundamental chemistry field and the bio-medical materials in the applied chemistry field are taken up. Bio-medical materials are used for the restoration, rehabilitation, and treatment of the organ and the improvement of its functions. For implants such as hearts, anti-thrombin and anti-calcium precipitation effects and high endurance are required. In this field, special copolymers and bio-membrane-emulating surfaces are studied. For artificial organs, hybrid type materials combining cells, and physiologically active and artificial materials are also studied. There are studies on the missile therapy of drugs and DDS (drug delivery system). The complex compounds contain metallic elements, such as Fe, Mn, Co and Cu, and groups known as ligands which combine these metal elements. They can have a variety of stereo-structures and physical properties. They also exhibit a diversity of functions including electron donor bonding, molecular recognition, chemical substitution, and pharmaceutical activity. These features open up a promising potential for their prospective use as physiologically active substances, cancerostats, new materials, artificial photosynthesis, memory elements, and complex catalysts. 88 refs., 35 figs., 6 tabs.

  12. Research and development project of production method of advanced chemicals by utilizing marine organisms. Kokino kagaku seihin nado seizoho (kaiyo seibutsu katsuyo) no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-01

    The research results in fiscal 1989 were reported of Research and development project of production method of advanced chemicals by utilizing marine organisms'' promoted by NEDO. After marine organisms were sampled in warm current and subtropical sea areas, aerobic bacteria, yeasts, algae and invertebrates were separated each other. The separation method of microorganisms habitable in cold areas was also found by their separated culture. Amounts and species of zooplanktons and phytoplanktons were surveyed in tropical sea areas to settle on organim sampling plans. The analysis method of lipide in marine microorganisms was found by applying conventional chemical analysis methods to it, and features of its constitutive fatty acids were clarified. The screening method of adhesive microorganisms with protein-decomposing function was found, and such bacteria could be separated. Patents and documents of the equipment related to sampling, separation, culture and preservation of marine organisms were surveyed, and a remote control organism sampler was designed basically.

  13. Synthetic focused array of electrical prospecting using pole-pole array potential data; Sanjigen denki tansaho ni okeru nikyokuho den`i data wo mochiita denryu shusoku haichi no goseiho

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-22

    Various methods have been put into practice for the conventional two-dimensional pole configuration using a single line in three-dimensional electrical prospecting. Pole configuration effective for the three-dimensional exploration has not been investigated. This paper describes synthetic focused array using four pairs of guarded poles based on pole-pole array potential data in the case of arrangement of measuring points on a grid. Results of the numerical simulation are also described. For the focused array, laterolog of electrical logging is applied to the surface prospecting. Directivity can be given to the current from the main pole by controlling the current from guarded pole. It was found from the simulation that the resistivity anomaly is concentrated directly on the embedded ball for the focused array rather than for the pole-pole array. It was also found that two conductive balls can be clearly separated for the focused array rather than for the dipole-dipole array. Accordingly, it was considered that results approximating the original structures can be obtained by analyzing using the both arrays. 5 refs., 6 figs.

  14. Effect of insolation forecasting error on reduction of electricity charges for solar hot water system; Taiyonetsu kyuto system no denki ryokin sakugen koka ni oyobosu nissharyo yosoku gosa no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

    1996-10-27

    A solar hot water system can be economically operated if inexpensive midnight power is purchased to cover the shortage of solar energy predicted for the following day. Investigations were conducted because error in insolation prediction affects the system operation and electric charge reduction effect. The target temperature of the heat accumulation tank at every predetermined time point is calculated on the previous evening in consideration of predicted insolation so that the water will be as hot as prescribed at the feeding time on the following day. Midnight power is used for uniform heating to attain the target temperature for 7 o`clock on the following morning. The uniform heating continues from 8 o`clock to the feeding time, this time using solar energy and daytime power to attain the target temperature. Accordingly, the division between the midnight power and daytime power is determined in view of the target temperature for 7 o`clock on the following morning, which target temperature is so set that the charge will be the minimum by optimizing the allocation of the above-said two. When the insolation prediction error rate is beyond 30%, the electric charge grows higher as the rate rises. But, when the rate is not higher than 30%, the charge is little affected by a rise in the rate. 5 refs., 10 figs., 1 tab.

  15. Operational environment of American electric business which has been critical under restrictions on power rates. Part 4. ; Investment risk and penaltu against capital cost. Ryokin kisei de shinkokukashita bei denki jigyo no keiei kankyo. 4. ; Toshi risk to shihon penalty

    Energy Technology Data Exchange (ETDEWEB)

    Nagao, T. (Japan Electric Power Information Center Inc., Tokyo (Japan))

    1991-10-01

    Regarding the policy to impose restrictions on the heightening in electric power rates by the state authorities to be a penalty against the capital cost against the electric power dusiness, the following contents are explaine: Whichaver bond or stock may be selected for the flotation as a method of raising the construction fund, newly necessary for the electric power business, the restrictions on electric power rates cause a heightening in fund raising cost to the electric power company. When those restrictions were severe in the USA, most electric power companies were lowered in evaluation rank to classify the bond. The lowering in evaluation rank to classify the bond flotation company heightens the burden of monetary interest and causes, in some cases, even a stoppage of bond flotation. The electric power company, if raising the fund under so severe restrictions on electric power rates as to have risk occur for the stock investment, suffers losses, i.e., lowering in stock prices and heightening in flotation cost. Further, there occur many cases that an enormous investment fund is lost due to the postponement or canellation of electric power station construction, caused by the restrictions on electric power rates.

  16. 55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-10

    Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

  17. Optimization of dynamic source depth for seismic surveys. Part 7; Dynamite shingen no hasshin shindo no saitekika ni tsuite (hyoso kozo no suitei (kusssetsuho jishin tansa oyobi denki denjiho tansa)). 7

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H.; Murayama, R.; Mitsuhata, Y.; Ishikawa, H. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-05-01

    For the improvement of quality of data collected by reflection aided seismic exploration using dynamite as the seismic source, information has to be collected about the surface layer structure before the charge depth is determined. For this purpose, refraction, electric, and electromagnetic exploration methods were tried. In the refraction method, an impactor was used as the seismic source. In the records, the surface wave prevails because vibration was generated on the surface. Analysis was made by the use of the initial travel time tomography. In the electric exploration, a double pole array was used to measure resistivity. The measured data was subjected to a fully automatic inversion for analysis. As the result, it was disclosed that it was useful to know the deep-level structure directly by use of tomographic methods in refraction seismic exploration so as to find the optimum charge level. Furthermore, about the electric and electromagnetic exploration techniques, it was found that these methods can be applied making use of resistivity to the evaluation of groundwater saturation. 7 refs., 5 figs., 3 tabs.

  18. Verification test for an electric vehicle using capacitor-battery series connection for battery load levelling; Denchi no fuka heijunka no tame no kyapashita to denchi no chokuretsu setsuzoku hoshiki wo saiyoshita denki jidosha no jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    Miyaoka, K.; Takehara, J.; Kato, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-03-25

    For the prolongation of the distance that an electric vehicle (EV) can cover on a single charge and of the service life of the EV battery unit, a system is developed, in which the battery unit and the capacitor unit are connected in series for the levelling-off of battery peak loads, and the system is tested aboard a running real vehicle. Installed on the real vehicle is a battery unit that is a series connection of 20 12V-38Ah seal-type lead-acid batteries, each battery consisting of two cells connected in parallel. Driving the vehicle is a DC brushless motor capable of a maximum operation of 9000rpm. Also installed is a capacitor unit that is a parallel connection of 40 2.3V-1800F capacitors, each capacitor consisting of two capacitors connected in parallel. Findings are described below. In a 0-400m acceleration test, 22.5 seconds is recorded with the capacitor unit in operation, meaning an improvement of 0.7 seconds. The maximum speed remains unchanged at 110km/h, which agrees with the pre-calculated value. Although the battery peak load reduction rate in a 15-mode drive pattern marks 23%, the distances covered on a single charge in this drive pattern turn out to be almost the same whether the capacitor unit is in operation or not. 3 refs., 15 figs., 3 tabs.

  19. Development of a high temperature electric resistance measuring apparatus and the applications to measurements for carbon materials. Koon denki teiko sokutei sochi no shisaku to tansokei zairyo eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Sato, S.; Kurumada, A.; Kawamata, K. (Ibaraki University, Ibaraki (Japan). Faculty of Engineering); Sasaki, T.; Shibano, M. (Ibaraki University, Ibaraki (Japan))

    1990-12-20

    A trial fabrication was done to build a vertical type high temperature electric resistance measuring apparatus utilizing an ultra high temperature electric furnace using graphite as a heater for the purpose of studying application of carbon materials under ultra high temperatures. Electric specific resistance was measured on carbon materials to a temperature of up to 2,400 {degree}C. The test pieces are of composite material composed of fine grain isotropic graphite, electrode graphite for steel furnace made by Arc, and C/C. The electric resistance was obtained using a voltage drop method at a reference current of 100 mA, and the specific resistance was calculated using the test piece diameter and the distance between electrodes. The temperature was raised at a rate of 550-600 {degree}C/h. All the graphite materials have their own individual values of electric specific resistance at the room temperature. As the temperature is raised, the specific resistance decreases, shows a minimum value, and then increases gradually showing a nearly constant increase rate until the temperature approaches the graphitization temperature of 3000 {degree}C. At low temperatures, the current carrier mobility is constant, but at higher than the normal temperature, mobility reducing speed becomes dominant because of heat excitation scattering, which is believed to increase the electric specific resistance. 5 refs., 12 figs., 5 tabs.

  20. Utilization of two-way multicore cables and comparison of various electrode configurations in electrical prospecting; Denki tansa ni okeru sohokogata tashin cable no riyo to kakushu dekyoku haichi no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Takakura, S. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1996-10-01

    For more precise electrical prospecting, the new multicore cable was developed to allow high-density measurement by conventional equipment. Since conventional multicore cables are inferior in cost, length and weight, the new cable is composed of an n-conductor cable, two n-conductor male connectors and n lead wires. For connection of the multi-conductor cable and lead wires, cable sheath is peeled at n points at specific intervals. Sheath of the k-th conductor is peeled at k-th point from the terminal, and restored for insulation after connection of the conductor and lead wire. The male connectors are attached to the both ends of the multi-conductor cable. Since this two-way type cable can be used at every end, the measuring equipment can measure at one divisional point after another of a long measuring line while shifting the equipment from one point to another. All measurements are perfected only with two short cables. Resistivities were successfully measured along the long measuring line of 480m long with 97 electrodes arranged at intervals of 5m. Various electrode configurations were also compared. 1 ref., 4 figs., 2 tabs.

  1. Study on the best utilization of solar energy. Experimental study of hydrogen generation by water electrolysis using solar battery; Taiyo energy no yuko riyo ni kansuru kenkyu. Taiyo denchi riyosui denki bunkai suiso hassei field test

    Energy Technology Data Exchange (ETDEWEB)

    Kawashima, Y.; Murai, K.; Nakai, T. [Himeji Institute of Technology, Hyogo (Japan)

    1997-11-25

    Shortcomings of solar energy are that it is subject to weather and is not available in the nighttime. The weak points may be effectively made up for when solar energy collected on a fine day is stored in the form of hydrogen energy for recovery as required. In this report, power generated by solar cells is used for the electrolysis of water for the generation of hydrogen. The amounts of the thus-generated hydrogen and hydrogen energy are determined and, on the basis of the measured amount of insolation, the solar energy availability rate (hydrogen conversion performance) is calculated. The amount of hydrogen generated in fiscal 1996 is also calculated for every month. The hydrogen generation level is quite low in the TiO2 wet type solar cell, approximately 0.2% at most. The current efficiency is fairly high in hydrogen generation using electrolysis, which is approximately 96-97%. The efficiency is higher when several units of electrolyte are connected in series until the solar cell optimum voltage is attained. A linear relationship is found between the daily summation of insolation and the amount of hydrogen generated. 1 ref., 7 figs., 2 tabs.

  2. Improvements in gate-dielectric characteristics of nitrided oxides prepared by rapid thermal processing. Kyusoku kanetsu chikka sankamaku ni yoru gate zetsuenmaku tokusei no kojo

    Energy Technology Data Exchange (ETDEWEB)

    Hori, T. (Matsushita Electric Industral Co. Ltd., Osaka (Japan))

    1991-11-10

    This paper indicates that, in improving gate-dielectric characteristics of MOSFET, a nitriding treatment (light nitridation) using the rapid thermal processing (RTP) is superior to a treatment using resistance heating furnace (heavy nitridation) in terms of the controllability of the teatment processes. Although a nitridation treatment alone will not be able to achive simultaneously the suppression of the interface level generation in the gate insulation films, and the reduction of electron capturing, the paper claims that both requirements can be met if nitrided oxide films generated by the nitridation are re-oxidezed by the RTP. It is suggested that when the re-oxidized nitrided oxide films (provided they are re-oxidized after light nitridation) are used for the gate insulation films in place of the conventional SiO{sub 2} films, the various characteristics representing the performance and reliability of micronized MOS devices (subthreshold characteristics, characteristics of insulation break-down with time, etc.) in general can be equivalent or better. 18 refs., 7 figs., 2 tabs.

  3. Mechanical properties and failure criterion of normally and over consolidated cement-treated soil; Seiki kaatsumitsu cement kairyodo no sendan tokusei to hakai kijun

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, J.; Nagaoka, T.; Tanizaki, S. [Tekken Corp., Tokyo (Japan)

    1997-03-21

    The shear properties and failure criterion of normally overconsolidated cement-treated soil were examined to solve the mechanical characteristics of cement-treated soil. As a result, the shear properties of normally consolidated cement-treated soil vary depending on the degree of the confining pressure and consolidated yield stress. Like the overconsolidated value, the shear properties of overconsolidated cement-treated soil are influenced by the confining pressure and consolidated yield stress values. Moreover, the failure criterion cannot be prescribed by the normally overconsolidated history, but the maximum and residual stress state line. The dependency of drainage conditions and confining pressures is detected when the rupture line of cement-treated soil is arranged by the whole stress. The rupture line obtained during drained shearing is excellent in the internal friction angle. The rupture line obtained during undrained shearing is excellent in cohesion. The rupture line in the maximum axial difference stress state is designed to cross with that in the residual stress state near the drained stress route in which the confining pressure and consolidated yield stress are the same. 11 refs., 13 figs., 3 tabs.

  4. Fatigue properties of austempered ductile cast iron at room and elevated temperatures; Austemper kyujo kokuen chutetsu no chukoon ni okeru hiro tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Fukuyama, K.; Hasegawa, N.; Inaga, K. [Gifu University, Gifu (Japan)

    1995-06-15

    Austempered ductile cast iron (ADI) is used widely as a structural material with high strength and toughness. However, since few studies have been made on investigation of fatigue properties at medium to high temperatures, this paper describes rotating bending tests carried out in temperature range between room temperature and 400{degree}C to investigate the fatigue properties and the fatigue crack generating behavior. The following results were obtained: the fatigue limit (fatigue strength after 10{sup 7} bendings) showed a remarkable maximizing phenomenon at temperatures around 300{degree}C; micronization of the base structure caused by transformation of residual austenite was recognized above 300{degree}C, and so was rise in the hardness; heating to this temperature led to rise in the Ms point, making the transformation occur more easily; the effect of repetitive stress causes a processing induced transformation; the temperature at which the transformation and the micronization are completed declines by about 50{degree}C lower than in the non-transformed region; and the fatigue fracture at middle to high temperatures is caused more frequently by internally existing graphite and development of cracks from very small casting cavities. 31 refs., 10 figs., 7 tabs.

  5. Which site-specific characteristics estimated from microtremors are useful?; Bido kara suitei sareta jiban tokusei no uchi nani ga riyo dekiruka

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, B.; Horike, M.; Takeuchi, Y. [Osaka Inst. of Tech. (Japan)

    1998-07-30

    Microtremors are in existence anywhere and at any time, and are possible to be applied to the estimation method for practical site-specific characters because their observation is easy and most efficient. Using the records of microtremors and earthquake observed by arrays installed on the alluvial and diluvial grounds in the Osaka plain and on reclaimed land in the Kyoto basin, possibility of estimating site-specific characteristics from microtremors is investigated, and the validity of the conclusion drawn by the use of Kushiro array is examined. HV (horizontal-to-vertical) spectral ratio is superior to power spectrum as the method of estimating dominant frequency of ground using microtremors. When a distinct peak appears in the HV spectral ratio, it indicates that the ground structure has large contrast, and the peak coincide with the predominant frequency of ground motion. HV spectral ratios of microtremors are possible to be used for estimating spatial variation of earthquake motion in areas with diameters of a few hundred meters where the degree of input of the microtremor source is considered to be nearly equal. HV spectral ratio of microtremor seems to be possible to be applied to the estimation of the vertical components of earthquake motion from the horizontal motion. 25 refs., 12 figs., 1 tab.

  6. Antibacterial characteristics of heated zinc oxide powders on Escherichia coli and Staphylococcus aureus; Kanetsu shori sareta sanka aen funmatsu no daichokin oyobi oshoku budoukyukin ni taisuru kokin tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sawai, J.; Yamamoto, O.; Hotta, M.; Kojima, H.; Sasamoto, T. [Kanagawa Inst. of Tech., Kanagawa (Japan)

    1998-09-10

    Influence of heat treatment temperature of zinc oxide (ZnO) powders on antibacterial property against Escherichia coli and Staphylococcus aureus was studied. The values of the minimal inhibitory concentrations (MIC) were determined by the electric conductance method to examine the antibacterial property. MIC is defined as concentration at lowest temperature where no changes of the conductance are detected. MIC of ZnO powders increases with an increase in heating temperature. The variation of MIC against E. coli is larger than that against Staph. aureus. Concentration dependence of antibacterial effect by hydrogen peroxide is larger against E. coli than that against Staph. aureus and agrees to the variation tendency of MIC with ZnO powders. The difference in the sensitivity against E. coli and Staph. aureus is suggested to be due to the action of hydrogen peroxide generated from ZnO powders. 8 refs., 3 figs., 1 tab.

  7. Heat storage characteristics of latent microcapsules using hot air bubbles by direct contact heat exchange; Onshitsu kihogun to sennetsu microcapsule tono chokusetsu sesshohku kokan ni yoru chikunetsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, K.; Sugiura, T. [Toyohashi University of Technology, Aichi (Japan)

    2000-05-25

    This paper has dealt with the heat storage characteristics of fine microcapsules packed with latent heat storage material in the water layer. The heat storage operation to the latent microcapsules was carried out using hot air bubbles by direct contact heat exchange. The microcapsule consists of n-paraffin as a core latent-heat storage material and melamine resin as a coating substance. The relation of the completion time of latent-heat storage to some parameters was examined experimentally. The non-dimensional correlation equations for the completion time of latent-heat storage process had were derived in terms of the ratio of water layer height to diameter of microcapsule, Reynolds number for air flow, Stefan number and modified Stefan number for absolute humidity of flowing air. (author)

  8. Physical properties and microstructure of silica ore, and their effect on phase transition; Keiseki genryo no butsusei{center_dot}bikozo to soteni tokusei tono sokan

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K.; Hatae, E.; Mishima, M.; Asano, K.; Yamato, T.

    1999-12-01

    Physical properties, microstructure and phase transition of silica ore produced in Japan, China and India were investigated. Japanese ore is a composite quartzite structured by fine crystals and large crystals of hundreds micron m., while Indian and Chinese ores are quartzite such as recrystallized quartzite and sandy quartzite, composed mainly by large crystalline. What promotes phase transition is supposed to be mainly Al{sub 2}O{sub 3}, and quartz in the composite quartzite show quick phase transition at lower temperature than the quartz in other materials. (NEDO)

  9. Effect of burn-off on physical and chemical properties of coal char; Gas ka shinko ni tomonau sekitan char no tokusei henka

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, T.; Tamura, K.; Hashimoto, H.; Funaki, M.; Suzuki, T. [Kitami Institute of Technology, Hokkaido (Japan)

    1996-10-28

    For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the gasification. However, their catalytic effect is related with chemical forms, and complex as they may change into inactive sulfides and silicates under severe reaction conditions. Change in forms of calcium compounds may also be involved in decline of the reactivity in the latter stage. 8 refs., 4 figs.

  10. Crack wave propagation along fracture with an induced low-velocity layer; Teisokudo no chika kiretsu zone wo denpasuru kiretsuha no bunsan tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nagano, K. [Muroran Institute of Technology, Hokkaido (Japan)

    1997-10-22

    A study has been performed on underground cracks working as a geothermy reservoir layer, with respect to characteristics of elastic waves propagating with their energy concentrated on a boundary between rocks around the cracks and fluid in the underground cracks, or `crack waves`. The study has modeled a multi-crack reservoir layer according to the three-layer structure of the fluid layer and low-velocity solid layers around the former layer, whereas crack waves propagating therein were discussed for their dispersion characteristics. As a result of discussions, a guideline to the crack wave measurement at actual fields was put together as follows: because the low-velocity layer affects the dispersion characteristics of the crack waves, the structure and characteristics of the multi-crack reservoir layer may possibly be evaluated by measuring the velocity of the crack waves; evaluating the low-velocity layers requires proper selection of frequency of the crack wave to be measured; for example, at the Higashi Hachimantai field, a crack wave of several hundred hertz must be analyzed; and thickness of the low-velocity layers around main cracks, which can be estimated from the velocity of the crack wave is two meters at the greatest. 6 refs., 3 figs., 2 tabs.

  11. Output characteristics of floating type wave power generator system using a ball screw; Fuyugata nejishiki haryoku hatsuden sochi no shutsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Abe, T.; Omata, K. [Meiji University, Tokyo (Japan)

    1996-10-27

    A floating type wave power generator system using a ball screw is proposed. Output characteristics are simulated on the supposition of its employment aboard a navigational aid buoy. The relative linear movement produced by waves between the main body and float is transmitted via a load column to a ball nut and is converted into a rotary movement of a threaded shaft engaging the ball nut. Attached to the bottom end of the threaded shaft is a one-way clutch which connects to the generator axle when the relative velocity between the float and main body is positive. The simulation was conducted for a wave activated power generation buoy, 2.6m in outer diameter, 4.5m in length, and 6000kg in total mass. The buoy generated a mechanical output of 340kW when exposed to a sinusoidal wave 2.5 seconds in period and 40cm in wave height. A tank test was performed using a reduced scale model consisting of a ball screw, bicycle dynamo, and float, with the main body being 318mm in diameter and 833mm in length, when an average output of 4.51W was obtained at 60% efficiency. The results of the experiment agreed in some degree with the results of calculation, verifying the righteousness of the theoretical formula. 3 refs., 7 figs., 4 tabs.

  12. Ultrafiltration performance of tubular membrane modules fitted with turbulent promoter. Twisted tape and static mixer; Ranryu sokushintai wo sobishita kangata gengai roka tokusei. Twist tape to static mixer

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, T.; Kobayashi, H.; Ishikawa, T.; Kamiya, T. [Kogakuin University, Tokyo (Japan); Niitsu, T.; Inoue, H. [Soka University, Tokyo (Japan)

    1996-01-20

    The permeate flux of a membrane module fitted with a twisted tape or static mixer was 4-7.7 times higher than that of a membrane module without any turbulent promoter. Use of a twisted tape or static mixer shortened separation time. The energy consumption per unit mass of permeate due to pressure drop in the membrane module with twisted tape or static mixer was 2-3 times higher than that in the membrane module without turbulent promoter. The permeate flux solved by introducing the value of mass transfer coefficient into the osmotic pressure model coincided well with experimental results, where the mass transfer coefficient was obtained by simulating experimental formula of heat transfer in a pipe fitted with a twisted tape or static mixer into a mass transfer correlation by the heat transfer-mass transfer analogy. The mass transfer coefficient in a membrane module with twisted tape or static mixer increased to about 4 to 8 times that of a membrane module without turbulent promoter. 7 refs., 10 figs.

  13. Study of human interface for narrow road drive assist system considered characteristic of driver; Driver no tokusei wo koryoshita kyoro soko shien system no human interface no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, A. [Subaru Research Center Co., Tokyo (Japan); Amada, N.; Kawashima, H. [Keio University, Tokyo (Japan)

    1997-10-01

    The measurement of driver`s watching point, driving time on narrow road and the evaluation of stress etc. were conducted in order to construct the narrow road drive assist system using the stereo image recognition system. Consequently, the driver`s thinking process, stress factor and the indispensable information for this system were clarified. 4 refs., 8 figs., 3 tabs.

  14. Ground characteristics at observation site of strong motion in Hachinohe Inst. Tech. Hachinohe, Aomori; Hachinohe Kodai konai ni secchishita kyoshin kansokuten no jiban tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sakajiri, N. [Hachinohe Institute of Technology, Aomori (Japan)

    1997-10-22

    Discussions were given on ground structures in the city of Hachinohe and vibration characteristics of the grounds during earthquakes. In order to identify ground structures and vibration characteristics thereof in the city of Hachinohe, strong motion seismographs were installed in five locations of the city and in the Tohoku University. At the Hachinohe Institute of Technology, strong motion seismographs were installed underground (-65 m) and on the ground, where S-wave logging experiments were performed using the plank hammering method. The records therefrom were used to estimate Q values, and the Q values were used to compare the computed ground amplification characteristics with the spectral ratio of seismic waves in and on the ground. The analysis has conducted the Q value estimation on each bed from a depth greater than 4 m, whereas relatively reasonable values were derived only from sections from 4 m to 13 m, and other sections showed no stable values. According to the result of observations derived from the seismographs installed in and on the ground, the maximum amplitude of the ground surface seismograph was found about five times greater than that of underground in the NS components, about eight times in the EW components, and about six times in vertical movements. The result indicates that the amplitude is obviously affected greatly by the characteristics of the ground. 4 refs., 8 figs., 1 tab.

  15. Losses of new type HTS wires with transposed Bi-2223 filaments; Fuiramento ten'igata Bi-2223 tashin senzai no sonshitsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Watabe, K.; Yamashita, K.; Sumiyoshi, F. [Kagoshima Univ., Kagoshima (Japan); Hayashi, H.; Irie, F. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    2000-05-29

    In Bi-2223 multifilamentary wire, large hysteresis loss occurs by 'self-magnetic field effect' where transport current flows on the surface. To prevent from this, uniformity of transport current distribution by filament transposition is effective. Round wire with two layers of helical coil around Ag core material by four Bi-2223 multifilamentary wires was fabricated as trial. Uniform condition of current distribution was explored and twist angle was found to be an important parameter. Hysteresis loss of wound wire in a reverse direction was reduced by 1/3 compared with one of wound wire in a same direction and known wire. (NEDO)

  16. Study on property-gradient polymer electrolyte for rechargeable lithium batteries; Lithium niji denchi no tame no keisha tokusei kobunshi denkaishitsu no sosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kokumi, Z.; Kanemura, S.; Inaba, M.; Takehara, Z.; Yao, K.; Uchimoto, Y. [Kyoto University, Kyoto (Japan)

    1997-02-01

    This paper describes the fundamental experiments for creating property-gradient polymer electrolyte for rechargeable lithium batteries. The rechargeable lithium battery is composed of an anodic composite agent section with high ion conductivity, a separator equivalent section with high mechanical strength (high bridging degree), and a section surpressing the precipitation of metal lithium by contacting with it. The continuous property-gradient polymer electrolyte was tried to be synthesized by means of the plasma polymerization method. As a result, plasma polymerization electrolyte with high ion conductivity could be prepared from the liquid phase by using a monomer with low vapor pressure. Porous material simulating the anodic composite agent was impregnated by the monomer, which was plasma-polymerized. As a result, it was found that the bridging degree decreased from the surface towards the inside of the plasma-polymerized porous material. In addition, polymer was prepared using fluorine-base monomer. Thus, LiF thin film could be prepared through the reaction between the polymer and metal lithium. 3 figs.

  17. Improvement of magnetic properties of Fe-50mass%Ni in MIM process; MIM process ni okeru Fe-50mass%Ni no jiki tokusei kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Miura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Fujita, S. [Kumamoto University, Kumamoto (Japan); Fujita, M.; Ninomiya, R. [Mitsuikinzoku Co. Ltd., Tokyo (Japan)

    2000-12-15

    Metal injection molding (MIM) process is hoped to be one of processing for required to more complicated parts of magnetic components. In this study, the effect of different types of powders (prealloyed and mixed elemental powders) on the magnetic properties of permalloy (Fe-50mass%Ni) through the MIM technique was investigated. Approximately 94% of theoretical density was obtained by using the prealloyed powder, and the retained carbon and oxygen contents were controlled to be low. On the other hand, 96% of theoretical density was obtained by using the mixed elemental powder, but the magnetic properties were inferior to that of prealloyed powder's because of high retained oxygen content. By using the carbonyl Fe powder with high carbon, the retained oxygen and carbon content could be controlled to be low, resulting in the improved magnetic properties. (author)

  18. Influence of strain hardening and thickness changes occurring in press forming process; Seikeiji no kako koka/itaatsu henka no buzai akkai tokusei ni oyobosu eikyo bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, M.; Hirota, K. [Mazda Motor Corp., Hiroshima (Japan); Nakazawa, Y. [Sumitomo Metal Industries Ltd., Osaka (Japan)

    1997-10-01

    Most components of the body structure are produced by press forming. This process make a uniform metal sheet into a component that have various material characteristics and thickness. This paper describes the estimation method of material characteristics and thickness changes based on the measured Vickers hardness, and the influence of these changes on the crush performance by using FE analysis. 4 refs., 12 figs., 2 tabs.

  19. Hear recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system no fuirudotesuto ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Amanuma, H. [NTT Integrated Information and Energy Systems Laboratories Tokyo (Japan); Uekusa, T.; Waragai, S. [NTT Power and Building Eacilities Inc., Tokyo (Japan)

    1997-12-20

    NTT is developing a phosphoric acid fuel cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerator to cool the telecommunication rooms throughout the year. We fieldtested this fuel cell energy system in a telephone office for three years. Heat recovered water from fuel cell stack coolant was supplied to the absorption refrigerator and further extra-heat was recovered by a heat exchanger. The toral heat recovery amount was about 86000 kca/h (the heat recovery efficiency was 20%) under 200kW operation. The absorption refrigerator was supplied about 49000kcal/h of heat and operated with 0.7 of coefficient of performance throughtout the year. The electrical efficiency was maintained more than 38% after 13000h operation. 12 refs., 10 figs., 3 tabs.

  20. Heat recovery properties from fuel cell system for telecommunications use; Tsushin`yo nenryo denchi system ni okeru hainetsu kaishu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishizawa, M.; Iida, S.; Abe, I.; Yamamoto, M. [NTT Integrated Information and Energy Systems Laboratories, Tokyo (Japan)

    1997-08-20

    NTT is developing a phosphoric-acid fuel-cell energy system for telecommunication co-generation systems to reduce energy costs and help preserve the environment. Fuel cells are used to provide electrical power to telecommunication equipment and the heat energy that is generated is used by the absorption refrigerators to cool the telecommunication rooms throughout the year. We field-tested this fuel-cell energy system in a telephone office. Two heat recovery methods were applied in the test: one uses direct steam heat recovery from fuel-cell stack coolant to keep the heat recovery temperature high and to avoid requiring a heat exchanger for the recovery; the other uses heat recovery from the reformer exhaust gas that is directly in contact with the heat recovery water to recover heat more economically. Our field tests confirmed that the average efficiency of heat recovery from fuel-cell stack coolant is 16%, and from the reformer exhaust gas is 9% under 80-kW continuous operation. Maximum total efficiency including electrical power efficiency was confirmed to be about 73% under the condition of 100-kW and an S/C ratio of 2.5 in the winter period: heat recovery from the fuel-cell stack coolant was 23%, from the reformer exhaust gas was 10%, and from electrical conversion was about 40%. 9 refs., 12 figs., 1 tab.

  1. Properties of YBCO films grown by the sputtering method in low gas pressure; Tei gas sputtering ho ni yori keiseishita YBCO maku no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, T.; Kimura, H.; Suzuki, T. [Fuji Electric Corporate Research and Development, Ltd., Kanagawa (Japan)

    1996-06-10

    Formation of YBa2Cu3O2 (YBCO) films by low gas pressure sputtering and their characteristics are outlined. The film formation process proceeded at the substrate temperature of 650{degree}C, using a Y-Ba-Cu-O sintered body as the target, the (110) plane of MgO or SrTiO3 as the substrate, and Ar+50%O2 as the sputtering gas. When the substrate is positioned in the flight path of negative ions of oxygen, ions strike the film, causing re-sputtering and damage on crystals. When the substrate is positioned so that the distance between the target and substrate is approximately equal to the mean free path, crystals are damaged less, and an excellently oriented film is formed, the rate of growth being several times faster than that in the high gas pressure sputtering process. It has been found that film formation in pure Ar under the same low pressure (0.5Pa) also results in the formation of a YBCO structure, which means that oxygen required for film formation is supplied from the target. The relationship between film resistivity and temperature, or the dependence of film resistivity upon temperature, suggests that the film grows into an orthorhombic system. This is because the oxygen emitted by the target under low gas pressure is in the activated state when it lands on the film. 8 refs., 5 figs.

  2. Characteristic on photovoltaic/thermal hybrid collector. Evaluation of excergetic theory; Taiyoko netsu hybrid collector no tokusei. Exergy ni yoru hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Iwawaki, H.; Morita, Y.; Fujisawa, T.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Described herein are characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/Ts), in which a PV module is combined with a plate-shape solar heat collector to simultaneously produce electric power and heat. Their efficiency is assessed by exergy. The test results indicate that the PV/T system gives a 1.07 times higher exergy than the PV system, 86.3 versus 80.7kWh. In terms of energy, the optimum values (OVs) are 5, 44 and 37% lower than the measuring values (MVs) for electrical energy, thermal energy and total exergy. In terms of exergy, on the other hand, OV is 5% lower than MV for electrical energy, but 893 times higher for thermal energy and 1.26 times higher for total exergy. As a result, the exergy level is 26% higher than that of a system which generates power as the main product and heat as the auxiliary product. 3 refs., 6 figs., 5 tabs.

  3. High-field electrical properties of new LDPE films prepared using metallocene catalyst; Metallocene shokubai ni yori sakuseisareta shinki polyethylene film no kodenkai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ishimatsu, K.; Banmongkol, C.; Mori, T.; Mizutani, T. [Nagoya University, Nagoya (Japan); Ishioka, M.

    1998-07-01

    New Low Density Polyethylene (M-LDPE) prepared using metallocene catalyst has narrower composition distribution and molecular weight distributions than Linear-Low Density Polyethylene (LLDPE) using Ziegler catalyst. The authors compared the electrical insulating properties of M-LDPE films and conventional LLDPE films. The high-field current of M-LDPE was found to be lower than that of LLDPE. The difference in current increased with the decrease of temperature. The high-field current was much suppressed in M-LDPE with a low melting point. The impulse breakdown strength of M-LDPE raised with the decrease of temperature. The insulating properties of M-LDPE with a low melting point were improved at 30degC. These results were explained by a fact that M-LDPE with a low melting point includes more low-molecular-weight components. We also discussed the effects of antioxidant on the electrical properties of MLDPE. We compared the electrical conduction and breakdown strength of undoped M-LDPE and antioxidant-doped M-LDPE. The difference of their electrical properties were little. It was found that the excellent properties of M-LDPE do not depend on the effects or antioxidant. 11 refs., 12 figs., 2 tabs.

  4. Running characteristics of the superconducting magnetically levitated train in the case of the superconducting coil quenching; Chodendo jiki fujo ressha no chodendo coil quenching ji no soko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, H. [Kansai University, Osaka (Japan); Osaki, H.; Masada, E. [The University of Tokyo, Tokyo (Japan)

    1998-07-01

    A superconducting (SC) magnetically levitated (Maglev) transportation system has been developed in Japan and various experiments have been done in the new test line at Yamanashi prefecture. Although the superconducting electrodynamic suspension (EDS) system has the advantage of stable levitation without active control, various electromagnetic or mechanical disturbances can cause the change of gap length and the displacement or oscillation of the bogie. In this system, the severest disturbance is SC coil quenching. Therefore it is important to show the running characteristics of the Maglev train and to increase the stability in this case. We developed three dimensional numerical simulation program for the Maglev train. Using this program, running simulation of the train for Yamanashi new test track was undertaken in the case of SC coil quenching. Because of the damping characteristics of the EDS system, influence of the coil quenching is smaller at a higher speed. In the train model, electromagnetic spring strength of the EDS system is larger than mechanical spring of the secondary suspension system connecting a bogie and cabins. Therefore influence of the quenching is only seen in the cabins connected to the quenched bogie. Demagnetization of the SC coil quenching is considered to increase the stability of the train. Although this method is useful to decrease large guidance force, lateral displacement, yaw and roll angle of the bogie, vertical displacement and pitch angle become large. 10 refs., 17 figs., 2 tabs.

  5. Estimation of tire characteristics by concerning test data of vehicles; Jidosha no senkai shiken data ni yoru dire tokusei no suisan

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M.; Sekine, T.; Nagae, H. [Nihon University, Tokyo (Japan)

    1997-10-01

    To study and/or develop the vehicle motion of a braking in turns theoretically, the cornering characteristics of the tire under the action of braking forces must be required. On the other hand, such data are very few to be published and also there be few tire testing machine to be able to use. The authors tried to derive such data from the vehicle behaviors in steady turns and braking in turns. Because each wheel loads are unknown factors, the two wheeled vehicle model are employed in analysis. The methodology of analysis and the reasonable results are presented in this paper. 5 refs., 10 figs., 2 tabs.

  6. Breakdown characteristics of electro-negative gases under needle-plane gap. Hari-hiraita gap ni okeru denkiteki fusei gas no zetsuen hakai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, H.; Onoda, M.; Amakawa, K. (Himeji Institute of Technology, Hyogo (Japan)); Kuroda, S. (Nitto Denko Corp., Tokyo (Japan))

    1990-07-20

    The voltage-time (V-t) characteristics of corona onset and breakdown were examined in electro-negative gases as SF {sub 6} and CCl {sub 2} F {sub 2}, using a needle-plane electrode with small gap and {mu} s square pulse voltage with various wave fronts. The V-t characteristics in electro-neutral gas as N {sub 2} ordinarily descended rightwards, but those in SF {sub 6} descended rightwards only in smaller gaps and lower gas pressures. In the pulse voltage with shorter wave fronts, those in SF {sub 6} also offered a particular shape descending leftwards. The particular shape was dependent on the steepness of the pulse wave front, being strongly affected by shorter wave fronts, and also strongly related to the onset and development length of corona. The particular phenomenon of V-t characteristics was observed more obviously at a positive needle than negative one without any extremely long corona lengths at negative one, indicating a polarity effect. The phenomenon was also observed in CCl {sub 2} F {sub 2} as particular one in electro-negative gases. 21 refs., 12 figs.

  7. Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, H.; Nakada, T. [Isuzu Advanced Engineering Center, Tokyo (Japan)

    1997-10-01

    The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

  8. Development of C14 laves phase alloy for battery with good high-rate dischargeability; Koritsu hoden tokusei no sugureta denchiyo C14gata laves sogokin no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, H.; Wakao, S. [Tokai Univ., Tokyo (Japan); Mori, K. [Daido Steel Co. Ltd., Aichi (Japan)

    1998-07-05

    Authors have studied to develop Zr-Ti-V-Ni-Mn-Co(Fe,Mo) laves phase alloys for Ni-MH secondary batteries. The object of this study was to develop C14 laves phase alloys with good high-rate dischargeability. Alloys with enthalpy -triangleH for hydride formation in the range of 35 to 37 kJ/molH2 were designed using relations among the enthalpy, cell volume, and average atomic radius. The agreement between designed values and experimental results, and the differences of the enthalpy, cell volume and electrochemical characteristics, alloys with and without heat treatment, were studied. This paper describes first the principle of designing the alloys. Then the method of the experiment was explained The results and considerations were stated under the headings, i.e. Percentage of phase and cell volume, Enthalpy for hydride formation, Electrochemical characteristics of heat treated alloys and the same of as-cast alloys. 12 refs., 5 figs., 3 tabs.

  9. Forced convection heat transfer with microencapsulated phase-change-material slurries. Turbulent flow in a circular tube; Microcapsuleka sohenka busshitsu slurries no kyosei tairyu netsudentatsu tokusei. Enkannai ranryu

    Energy Technology Data Exchange (ETDEWEB)

    Yamagishi, Y.; Sugano, T. [Daido Hoxan Inc., Hokkaido (Japan); Takeuchi, H.; Pyatenko, A. [Hokkaido National Industrial Research Institute Sapporo (Japan)

    1998-01-01

    An experimental study using a slurry of micro-encapsulated phase change material (MCPCM) in water is conducted in order to investigate the increase in convection heat transfer coefficients of slurry flows as well as the increase in thermal capacity of a slurry by using the latent heat from a solid-liquid phase change material (PCM). Experiments were done for turbulent, hydrodynamically fully developed flows in a circular tube with constant wall heat flux. Local convective heat transfer coefficients were measured along the heating test section in order to study the effects of the melting phenomena inside MCPCMs. Experimental data are presented for various particle concentrations, slurry flow rates, and heating rates. Results show that an increase in the local convective heat transfer coefficient is found when the MCPCMs melted. Enhancement of heat transfer due to phase change is affected to varying degrees by Reynolds numbers of slurry flows, the fraction of PCM which is solid phase and heating rates. This paper provides and presents an explanation of the physical mechanism of the convective heat transfer enhancement due to the phase change of MCPCMs and a set of data available for the adjustments of system operating conditions for optimum heat transfer performance. 15 refs., 11 figs., 4 tabs.

  10. Evaluation of fatigue crack growth characteristics of WC-Co cemented carbides; WC-Co choko gokin no hiro kiretsu shinten tokusei no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, Y.; Boo, M. [Kanazawa University, Ishikawa (Japan). Faculty of Science; Kishi, Y. [Nippon Institute of Technology, Saitama (Japan); Park, Y. [Dong-A University, Pusan (Korea, Republic of)

    1997-07-15

    The fatigue crack growth tests of WC-Co Cemented Carbides were carried out in a wide range of fatigue crack growth rate covering the threshold stress intensity factor range {Delta} Kth. The effects of the stress ratio, Co volume fraction and the phase transformation of Co on the fatigue crack growth characteristics were investigated on the basis of fracture mechanics and fractography. The crack growth rate was measured using 3-point bending specimens. Crack growth tests were carried out at 10 HZ and the stress ratio R=0.1 and 0.5. The main results obtained are as follows; (1) The Paris rule can be applied between da/dN and{Delta}K and it is shown to be da/dN=C({Delta}K){sup m}. (2) The fractography of the fracture surface, shows that brittle fracture occurs in the Co binder phase at the stress rate R = 0.1 but ductile fracture occurs in the Co binder phase at R= 0.5. (3) The relation of da/dn-{Delta}Keff / E of WC-Co cemented carbides shows the characteristic in the middle of the other metals and the alumina ceramics. (4) The Co binder phase undergoes phase transformation by repeated deformation and so it affects the characteristics delicately. 22 refs., 9 figs., 3 tabs.

  11. Dynamic response of sliding isolating system using low yield strength steel; Goku nanko riyo suberishiki menshin sochi no doteki oto tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nagamachi, K.; Koike, T.; Wakinaga, T.; Nishimura, N. [Kawasaki Steel Corp., Tokyo (Japan)

    1998-01-01

    Bridge structure provided with the seismic isolation system discussed in this paper is subjected to analysis for its response to seismic motion for the study of the effect of the seismic isolation system. The isolation system has a low yield strength steel damper sandwiched between the upper and lower structures, and the relative displacement between the upper and lower structures is absorbed when the low yield strength tube is distorted for the absorption of seismic energy. In the analysis of its response to seismic motion, data of the Tokachioki-Hachinohe earthquake is used to represent a level 1 input and that of the Hyogo-ken Nambu earthquake a level 2 input. Findings are obtained as mentioned below. The isolation system is effective against level-2 seismic waves from earthquakes taking place just under and from those taking place between plates in the ocean. When the isolating system is optimally designed, as compared with the rigid system in the absence of an isolating system, the displacement of the lower structure due to seismic motion is reduced by 80% with the isolation system and by 70% with a damper. The sliding isolation system discussed in this report is applied to a steel bridge model built after the Ministry of Construction`s manual for isolating roads and bridges from seismic motion, and it is confirmed that the new system is effective in isolating the structures from seismic motion. 2 refs., 11 figs., 2 tabs.

  12. Shunt and series resistance of photovoltaic module evaluated from the I-V curve; I-V tokusei kara hyokashita taiyo denchi no shunt teiko to chokuretsu teiko

    Energy Technology Data Exchange (ETDEWEB)

    Asano, K.; Kawamura, H.; Yamanaka, S.; Kawamura, H.; Ono, H. [Meijo University, Nagoya (Japan)

    1997-11-25

    With an objective of discussing I-V characteristics when a shadow has appeared on part of a photovoltaic module, evaluations were given as a first stage of the study on saturation current, shunt resistance and series resistance for the solar cell module. As a result of measuring change in amount of power generated in a sunny day with a shadow appearing over the solar cell module, reduction in power generation capability of about 23% was verified. In other words, the I-V characteristics of the solar cell module change largely because of existence of the shadow caused on the module. The I-V characteristics curve may be expressed and calculated as a function of the shunt resistance and series resistance. By curve-fitting measurement data for a case of changing insolation without existence of partial shadow, values of the shunt resistance and series resistance were derived. As a result, it was found that the calculations agree well with measurements. It was made also clear that each parameter shows temperature dependence. 6 refs., 10 figs., 1 tab.

  13. Generation characteristics of photovoltaic power generation equipment at TEPCO R and D center; Gijutsu kaihatsu center taiyoko hatsuden setsubi no hatsuden tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Amano, K.; Natori, K. [Tokyo Electric Power Co. Inc., Tokyo (Japan)

    1997-11-25

    Solar battery arrays are installed at different tilt angles for actual measurement in an experiment conducted by TEPCO (Tokyo Electric Power Company, Inc.) Research and Development Center for the examination of their power generation characteristics. Arrays of polycrystalline silicon solar battery modules are positioned facing a direction +7 degrees swung from the south on the Center rooftop and verandah, and they are installed at tilt angles of 0, 30, 60, and 90 degrees. An analysis of system characteristics is conducted, and findings mentioned below are obtained. In fiscal 1996, the highest utilization factor of a yearly average of 11.3% is attained with the ones tilted at 30 degrees. As for the utilization factors at the other angles, they are 10.2% at 60 degrees, 8.8% at 0 degrees, and 8.0% at 90 degrees. The integrated design coefficient remains approximately constant irrespective of the different tilt angles of 0, 30, and 60 degrees. The overall design coefficient of the 90 degree-tilted array installed on the verandah is found to be 0.75, which is higher than those exhibited by the others. Appropriate routes of wirings for modules should be worked out to avoid the ill effect of the shadows of steel towers. 2 refs., 11 figs.

  14. Analysis of output characteristics of PV modules under natural sunlight; Shizen taiyokoka ni okeru taiyo denchi module shutsuryoku tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Murai, Y.; Igari, S. [Japan Quality Assurance of Organization, Tokyo (Japan)

    1997-11-25

    The paper measured current/voltage characteristics of various PV modules under natural light and analyzed various characteristics such as generated output and module power generation efficiency. In the experiment, installing various PV modules at the solar techno center located at north latitude 34.7deg and east longitude 137.6deg, measurement was made by I-V curve tracer, pyranometer, and thermocouple buried on the module back. As a result, the following were confirmed: As to the monthly mean power generation efficiency, the crystalline system is lowest in summer and highest in winter, and the amorphous system highest in summer and lowest in winter. Concerning the power generation efficiency and illuminance, the gap of power generation efficiency between at high illuminance and at low illuminance is large in the crystalline system and small in amorphous system. Relating to the azimuth angle of module installation and the generated output, the installation inclined 15deg angle west in summer and 15deg angle east in fall/winter generates more power in the crystalline system. On the contrary, the installation on the south face generates more power in the amorphous system. 4 refs., 8 figs., 3 tabs.

  15. Fundamental analysis of thermally regenerative fuel cell utilizing solar heat; Taiyonetsu wo riyosuru netsu saiseigata nenryo denchi no kiso tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Y.; Tanaka, T.; Takashima, T.; Doi, T. [Electrotechnical Laboratory, Tsukuba (Japan); Aosawa, T.; Kogoshi, S. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Study was made on a thermally regenerative fuel cell using solar heat. The thermally regenerative fuel cell was devised which is composed of 2-propanol liquid-phase endothermic dehydrogenation at nearly 100degC, and acetone liquid- phase exothermic hydrogenation at nearly 30degC as reverse reaction. This low-temperature dehydrogenation can relatively easily utilize a flat solar heat concentrator. 2-propanol dehydrogenation generates acetone and hydrogen. Generated acetone generates electric power in hydrogenation, generating propanol. This propanol regenerates acetone and hydrogen in dehydrogenation. The activity of Ru and Pt composite catalyst was considerably higher than that of Ru or Pt single catalyst. The activity was also higher in carbon felt or carbon cloth carrier than carbon plate carrier. The open circuit voltage of the fuel cell was estimated to be 110-120mV, nearly consisting with theoretical values. Short circuit current was also estimated to be 9-11mA, suggesting reduction of its internal resistance as an important subject. 4 refs., 5 figs., 2 tabs.

  16. Concentration characteristics and cell arrangement in luminescent concentrator PV modules; Keiko shukogata taiyo denchi module no cell haichi to shuko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, A. [Science University of Tokyo, Tokyo (Japan); Sakuta, K. [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    A luminescent concentrator PV module requires no tracking equipment and can use scattered light. A mini PV module was prepared from a luminescent plate of 100times100times3mm, and a single-crystalline PV cell of 100times20mm. Characteristics of various prototype modules with different PV cell areas and cell arrangements were also measured. Four kinds of edge reflecting materials with different reflectances by various white coating were applied to Al sashes for module frames, and each sash was fixed on one edge of the luminescent plate. In experiment, 3 other edges were covered with black tapes to reduce each reflectance to 0%. Although PV module output was affected by reflectance of edges, the output was satisfactory at 90% or more in reflectance showing no difference in output. A concentrating efficiency decreased with an increase in luminescent plate (concentrator) area, while it was improved by cell arrangement with short optical pass length, and cell arrangement hardly affected by edge reflection. 4 refs., 7 figs.

  17. Luminescence property and lowest excited singlet state level of various carotenes; Shuju no karochinrui no hako tokusei to saitei reiki -juko jotai jun'i

    Energy Technology Data Exchange (ETDEWEB)

    Ito, T. [Miyagi Midical Univ., Miyagi (Japan)

    2000-01-01

    Specification of the lowest excited singlet state (S{sub l}) of the butadiene which is the simplest {pi} electron conjugated system molecule has not sufficiently clarified at present. Recently, Andersson et al. found the weak light emission which was considered to be the S{sub 1} fluorescence in a near infrared region in a room temperature solution of {beta}- carotene (n=11), and specified the S{sub 1} level in 14,200{+-}500cm {sup -1}. And, Fujii et al. reported the S{sub 1} fluorescence of spheroidine (n=10). In very recent, Christensen et al. measured the comparatively clear fluorescence spectrum of carotenes n=5 to 11 separated by HPLC in EPA glass at 77K, and systematically examined the unique luminescence property observed in polyene. Christensen et al. issued the warning for the rough conventional method that the S{sub 1} level was estimated from the S{sub 1} fluorescence lifetime of the polyene molecule using the comprehensive energy gap law, because the ratio of quantum yield of the S{sub 1} and S{sub 2} fluorescence is different by the substituent type of the polyene end even if n is same. (NEDO)

  18. Fatigue life prediction of CFRP using evolution of creep property; Hiro katei ni okeru creep tokusei no henka wo mochiita CFRP no hiro jumyo yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Kanagawa, Y.; Fujii, T.; Sato, A. [Nagoya University, Nagoya (Japan). Faculty of Engineering

    1996-05-15

    A damage criterion on CFRP under fatigue loading defined in terms viscoelasticity is proposed. In order to elucidate the change in viscoelastic property of CFRP composites rider cyclic loadings this to matrix hardening, matrix crack, interface debonding and delamination a series of creep tests was incorporated during monotonic tensile fatigue test. A generalized Voigt model was applied to describe the creep behavior of the damaged composites. By use of the increment of creep strain induced by internal damage growth, a damage variable was proposed in the framework of Kachanov-Ravotnov`s classical damage theory. The evolution of the damage variable in relation to the maximum stress is discussed. Lemaitre-Chaboche`s damage evolution equation was employed to estimate the fatigue life of composites successfully. 8 refs., 8 figs.

  19. Characteristics on the heat storage and recovery by the underground spiral heat exchange pipe; Chichu maisetsu spiral kan ni yoru chikunetsu shunetsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Imai, I. [Kure National College of Technology, Hiroshima (Japan); Taga, M. [Kinki University, Osaka (Japan)

    1996-10-27

    The consistency between the experimental value of a soil temperature and the calculation value of a soil temperature given by a non-steady heat conduction equation was confirmed. The experimental value is obtained by laying a spiral heat exchange pipe in the heat-insulated soil box and circulating hot water forcibly in the pipe. The temperature conductivity in soil significantly influences the heat transfer in soil. The storage performance is improved when the temperature conductivity increases because of the contained moisture. As the difference between the initial soil temperature and circulating water temperature becomes greater, the heat storage and recovery values increase. A thermal core heat transfer is done in the spiral pipe. Therefore, the diameter of the pipe little influences the heat storage performance, and the pitch influences largely. About 50 hours after heat is stored, the storage performance is almost the same as for a straight pipe that uses the spiral diameter as a pipe diameter. To obtain the same heat storage value, the spiral pipe is made of fewer materials than the straight pipe and low in price. The spiral pipe is more advantageous than the straight pipe in the necessary motive power and supply heat of a pump. 1 ref., 11 figs., 1 tab.

  20. Development of metal complexes which has a novel type of dhotocatalysis activity; Shinki hikari shokubai tokusei wo yusuru kinzoku sakutai no sousei

    Energy Technology Data Exchange (ETDEWEB)

    Ishitani, Osamu [Saitama University, Saitama (Japan). Graduate School of Sceince and Engineering

    1999-12-16

    Purpose of this research are (1) development of photocatalysts which selectively drive hydride transfer and (2) their application to the enantioselective reduction of an unsaturated substrate. photocatalysis of [Ru(bpy){sub 2}(py){sub 2}]{sup 2+} (1) and [Ru(tpy)(bpy)(py)]{sup 2+} (2) (bpy=2,2'-bipyridine, tpy=2,2' : 6',2' '-terpyridine, py=pyridine) for reduction of unsaturated compounds was investigated using triethylamine as a reductant. Formation of the hydrogenated compounds was observed but the corresponding one electron reduced compounds were not detected at all. The complex 1 photocatalysed the reduction of trifluoroacetophenone (5) and gave the alcohol in a 67% yield but 2 gave only a 27% yield. The reaction proceeds via the photosubstitution of a py ligand of the ruthenium complex, followed by photochemical formation of the hydride complex. The ruthenium hydride complex reacts with 5 to give [Ru(tpy)(bpy)(OCHPhCF{sub 3})]{sup +} (4). Dissociation of 4 to the alcohol was not efficient and the yield was 10%. (author)

  1. Effect of Water Environment on Subcritical Crack Growth of Machinable Ceramics; Kaisakusei seramikkusu no kiretsu shinten tokusei ni oyobosu mizu kankyo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Kaizu, K.; Inotani, T. [Miyazaki Univ., Miyazaki (Japan); Yoshikawa, A.; Adachi, K.; Igaki, H. [Osaka Sangyo Univ., Osaka (Japan)

    1997-06-15

    The fatigue behavior of ceramics has been discussed on the basis of the relation between stress intensity facter (KI) and crack velocity (V). In this paper, the effect of environment on the relation between KI and V was studied on machinable ceramics (mica glass ceramics) and two kinds of glass ceramics with different grain sizes. The double torsion (DT) technique was used for the determination of the KI-V characteristics under different environments of air and ion-exchanged water. The characteristics of acoustic emission (AE) during stress corrosion cracking of mica glass ceramics was also examined. In water environment, the region II in the KI-V curve, in which crack velocity varies slowly with KI, disappeared. From this experimental fact, it was considered that at high KI, the crack velocity is encouraged by diffusion of the corrosive species to the crack and thus depended on the amount of water. SEM farc tography revealed that mica single crystals in the material caused crack arrest and deflection to occur. It is also found that AE event rate is quantitatively related to the crack velocity. AE measurement can be used in studying the crack propagation behavior of mica glass ceramics. 11 refs., 12 figs., 3 tabs.

  2. Linear elastic analysis of pavement structure under non-circular loading

    CSIR Research Space (South Africa)

    Maina, JW

    2012-10-01

    Full Text Available , South Africa b Century-techno Inc., Geo-technology Analysis Section, 2-8 Nihonbashi Kodenba-cho Chuo-ku Tokyo 103-0001, Japan c Department of Civil and Environmental Engineering, Tokyo Denki University, Hatoyama- Cho, Hiki-Gun, Saitama, 350...

  3. Transient response of CMRR in guard shielded isolation amplifier. Overall CMRR characteristics of an analog input system composed of a signal source, a wiring, a multiplexer and an isolation amplifier; Hogo shaheitsuki zetsuen zofukuki no CMRR kato tokusei. Shingosen, maruchipurekusa oyobi zofukuki kara naru sogotekina anarogu nyuryoku system no CMRR tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Maehana, Y. [Alphatech Co. Ltd., Tokyo (Japan); Nitta, S. [Tokyo Univ., of Aguriculture and Technology, Tokyo (Japan)

    1994-12-20

    In the measuring system like the computers used in industry, the analog input system for inputting the multi-signals from the sensors of pressure, temperature, flow into the data-processing device is installed. Analog input system is composed of a multiplexer for switching, choosing and inputting multi-signals; an insulating amplifier for amplifying the chosen signals and meanwhile insulating the signal source and data processing system; and a transducer for changing the analog signals into digital signals. In this paper, for making it possible to design quantitatively the frequency characteristics and transient responses of CMRR in analog system with multiplexer using guard shielded isolation amplifier with consideration of the effect of signal line, the analysis using an equivalent circuit with the simple input unit comprising signal line and analog input system, and its transfer function as well as the transfer function of amplifier is proposed. Then the experiments on three kinds of cases are carried out and the conformity thereof are verified. 9 refs., 11 figs., 6 tabs.

  4. Characteristics of gas-liquid two-phase flow in rotating pipe. 2nd Report. Pressure characteristics in downstream of the entrance of rotating pipe; Kaiten enkannai kieki nisoryu no ryudo tokusei ni kansuru kenkyu. 2. Kaitenkan iriguchi karyuiki ni okeru atsuryoku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, H.; Osaka, Y. [Doshisha University, Kyoto (Japan). Faculty of Engineering

    1997-04-25

    In the present study, we report experimental results obtained from air-water two-phase flows in the downstream region of a rotating pipe which consists of three independent rotating parts with a total length of 3 m. The pressure drop characteristics associated with the change in flow behavior due to effect of the pipe rotation are examined. Particular attention is paid to the length of the rotating pipe on the pressure drop characteristics. From the results of experiment, it is revealed that the effect of the rotating pipe becomes significant in the downstream of the entrance. A correlation based on the consideration of bubble fusion number applied to the bubble fusion model (proposed in the previous report) can be used to estimate the friction multiplication factor {phi}L{sup 2} satisfactory in bubble flow and plug flow regimes for the developed rotating two-phase flows. 9 refs., 6 figs.

  5. Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kamimori, K.; Sakai, K.; Ishihara, O. [Kumamoto University, Kumamoto (Japan)

    1996-10-27

    The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

  6. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  7. FY1999 Meeting of The Society of Heating, Air-Conditioning and Sanitary Engineering of Japan. Reduction measures against indoor air pollution due to chemical substances; 1999 nendo gakujutsu koenkai gaiyo. Kagaku busshitsu ni yoru shitsunai kuki osen teigen taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Iwata, T. [Tokai University, Tokyo (Japan)

    1999-12-05

    Serial A-10 and A-11 reported the experimental result on a bake-out effect by using composite materials, and reduction of formaldehyde and VOC generation after bake-out of building elements such as floor and baseboard. Specific combination of composite materials and ignored rebound were pointed out. A-12 reported the study on the effects of specific building materials, draft and ventilation, bake-out, and an air conditioning system using formaldehyde-removed materials for residences in cold areas. Bake-out time too short was pointed out. A-13 reported the formaldehyde reduction effect of low-formaldehyde building materials, ventilation and scavenger based on measurement in a new residence before dwelling. Discussion was held on the use method of formaldehyde scavenger. A-14 reported the considerable removal effect of a portable formaldehyde remover using a diffusion scrubber method based on the experimental research result at high and low formaldehyde concentrations. On a question about its applicability to a space there is continuous generation of formaldehyde and a humidity problem, the speaker answered that those remain unsolved for future studies. (translated by NEDO)

  8. History and recent practices of chemical cleaning for power plant boilers in China. Chugoku ni okeru hatsuden'yo boiler no kagaku senjo no hensen to saikin no jisshirei

    Energy Technology Data Exchange (ETDEWEB)

    Jie, H. (East China Electric Power Test and Research Institute, (China))

    1993-06-01

    This paper summarizes the change and the latest technologies for chemical cleaning for power plant boilers in China quoting a large number of the practices. High-pressure boilers have become constructed since the 1960's, for which water quality control has been applied, as well as hydrochloric and sulfuric acid cleaning, degreasing using alkaline chemicals, and phosphate passivation process. Thereafter, as ultra high-pressure facilities like once-through boilers, ultra high critical pressure facilities, and nuclear power facilities have entered into operations, organic acid cleaning, chelate cleaning, and EDTA-formic acid-hydroxy acetic acid cleaning have become used. Being carried out in addition to ordinary processes are use of solution accelerating agents, oxidizing ammonification, addition of thiourea, use of rinsing agents, and use of passivating agents. Evaluations and considerations were given on cleaning cycles, application procedures, and cleaning chemicals used on 336 units in total. As a result, it was indicated that chemical cleaning before starting operation of a new boiler is important, and futuristic EDTA would be more advantageous. 5 tabs.

  9. Report on evaluation on endocrine disturbing effect of chemicals and development of test methods; 1999 nendo kagaku busshitsu no naibunpi kakuran koka ni kansuru hyoka oyobi shikenho no kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With regard to endocrine disturbing effect being the new deleteriousness of chemicals, data were collected and evaluated by using the existing testing methods, data were collected by using the screening test, the testing methods were developed, and international investigation was carried out to establish the risk evaluation methods. In the evaluation by using the existing test methods, seven substance groups deficient in deleteriousness data qualitatively and quantitatively were given reproduction toxicity tests to evaluate availability of the endocrine activity. Development of the screening test method has been carried out by participating the validation test by OECD to make the uterotrophic assay method and the Hershberger assay method a test guideline having international matching property. International investigations to establish the risk evaluation were executed on the molecular mechanism of nuclear receptors, the chemical, metabolic and environmental behaviors of endocrine active substances, the effects of the endocrine active substances on experimental animals and human, the utilization thereof for risk assessment in human, and the effects of endocrine disturbance acting substances in wildlife species. (NEDO)

  10. Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-07

    Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

  11. Numerical simulation of hypersonic non-equilibrium wake flow using a higher-resolution method; Goku choonsoku netsu kagaku hiheiko wo koryoshita donto buttai koryu no kokaizodo suchi kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Nagatomo, H.; Yamamoto, S.; Daiguji, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-08-25

    An object which flies hypersonic speed, such as an aeroassisted orbital transfer vehicle, is affected greatly by not only the bow shock but also the expansion around the shoulder and the recompression of separated flow. Though the experiments to analyze this flow have been performed by some groups recently, there are some difficulties in measuring the flow because of limitations of instrumentation. Both experimental and numerical approaches are necessary to analyze the phenomena. The efficient numerical code which has been developed by the authors for hypersonic thermochemical non-equilibrium flow is applied to simulate the problem. The calculated results of different accuracies in space, the perfect gas and the experimental data are compared. 12 refs., 10 figs., 1 tab.

  12. FY 2000 study report on the study on technological development of the chemical processes of the next generation; 2000 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The technological development of the innovative chemical reaction processes is studied, in order to accomplish further energy saving, and reduction of resource consumption and environmental loads. Described herein are the FY 2000 study results. The program for systematization of the next-generation chemical processes systematically pigeonholes the undergoing projects and subjects to be studied, based on the principles of simplification, and sets the study fields of organic bulk chemicals, organic fine chemicals, highpolymer materials and inorganic materials. The program for investigation on next-generation chemical processes reviews creation and technological use of tailor-made biocatalysts, polymer materials which utilize wood resources, tailor-made reaction process engineering for handling fine particles in high-temperature reaction fields, production and processing of materials for high-performance polymer batteries, and extreme energy saving process for polyolefins, and proposes the revisions. The newly proposed study themes include novel C1 catalytic processes toward minimal wastes, and high utilization of biotechnology for novel processes to create materials. (NEDO)

  13. Water-stable Lewis acids. Aiming at a chemical reaction which is friendly to human being and the environment; Suichu de anteina ruisusan - hito to kankyo ni yasashii kagaku hanno wo mezashite -

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, S. [Science Univ. of Tokyo (Japan)

    1997-10-01

    A series of groups of compounds including rare earth triflates has been found which break the common knowledge of chemistry that Lewis acids are hydrolyzed in water and consequently inactivated. These compounds are stable in water and , in addition, function as a Lewis acid in water. This report describes the properties of and methods for preparing the above compounds. In particular, since the rare earth triflates have a higher solubility in water tan in organic solvents, they can be recovered merely by extraction after the completion of the reaction. Further, the reuse of the recovered compounds does not lower the catalytic activity, enabling the rare earth triflates to construct a system which can basically eliminate the need to dispose of the catalyst. This leads to realization of a chemical reaction which uses an aqueous solution and is the so called `an environmentally friendly chemical reaction.` The Mannich reaction in an aqueous solution, direct allylation of saccharides, and an alder reaction in a micelle system using a Lewis acid are described as examples of reactions using water-stable Lewis acids. 6 refs., 1 tab.

  14. 電力連盟と電気委員会 : 電力業におけるカルテルと公益規制

    OpenAIRE

    橘川, 武郎

    1982-01-01

    The purpose of this paper is to compare the origin and function of Denryoku Renmei with those of Denki Iinkai, and to make clear the relation between the cartel control and the public regulation concerning the electric power industry in the first half of the 1930s. Denryoku Renmei (the League of Electric Power Companies) was the cartel organized by five big electric power companies, Tokyo Electric Light Co., Great Consolidated Electric Power Co., Toho Electric Power Co., Nippon Electric Power...

  15. Cognitive and Neural Bases of Skilled Performance.

    Science.gov (United States)

    1987-10-04

    the NYU Neuromagnetism Laboratory. Finally, two of us attended the World Biomagnetism Conference in Japan in September 1987, and a paper was presented...Lloyd Kaufman 10/16/87 0 TV . Tech Report Page 19 "%,€ of Spontaneous Activity, to appear in: Biomagnetism 󈨛: Proceedings of the 6th International...Conference on Biomagnetism , Tokyo Denki University Press, Tokyo), in press. V.O. Kelhl, J. M. Pukki, R. S. Peltonen, A. J. Penttinen, R. J. ilmoniemi

  16. Estimation of site effects in Higashinada Ward, Kobe City using aftershock records of the 1995 Hyogo-Ken Nanbu Earthquake; Hyogoken nanbu jishin no yoshin kiroku wo mochiita Kobeshihigashinadaku no jiban zofuku tokusei no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kurita, K.; Yamanaka, H.; Seo, K. [Tokyo Inst. of Tech. (Japan)

    1998-07-30

    Source spectra and site effects are separated using the aftershock records, and the characteristics of short period earthquake motion in Higashinada Ward, Kobe City including the area to the south of seismic intensity 7 area are investigated placing emphasis on how far the site effects can be explained by 1-D ground structure. The shape and amplitude of the site effect of KNN and KYC located outside the seismic intensity 7 area can be explained fairly well by 1-D multiple reflection theory of S wave. However, peaks near 3 to 4Hz of KNN and UOZ in seismic intensity 7 area can not be explained. This suggests that the site effects of seismic intensity 7 area obtained by the aftershock records might include 2-D effects of underground structure. Inversion is performed using site effects as the objective functions to determine S wave velocity structure and Qs in the sedimentary layer. S wave velocity structure shows no systematical difference from those of the past models. 22 refs., 13 figs., 2 tabs.

  17. Initiation and propagation life distributions of fatigue cracks and the life evaluation in high cycle fatigue of ADI; ADI zai no ko cycle hiro kiretsu hassei shinten jumyo bunpu tokusei to jumyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ochi, Y.; Ishii, A. [University of Electro Communications, Tokyo (Japan); Ogata, T. [Hitachi Metals, Ltd., Tokyo (Japan); Kubota, M. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-15

    Rotating bending fatigue tests were carried out on austempered ductile cast iron (ADI) in order to investigate the statistical properties of life distributions of crack initiation and propagation, and also the evaluation of fatigue life. The results are summarized as follows: (1) The size of crack initiation sites of the material was represented by a Weibull distribution without regarding to the kinds of crack initiation sites such as microshrinkage and graphite grain. The crack initiation life scattered widely, but the scatter became much smaller as soon as the cracks grew. (2) The crack propagation life Nac which was defined as the minimum crack propagation rate showed lower scatter than the crack initation life. (3) The fatigue life of the material was evaluated well by Nac and the propagation rate after Nac. It was clear that the fatigue life of ductile cast iron was goverened by the scatter of Nac. 8 refs., 13 figs., 4 tabs.

  18. Estimation of spectral solar radiation based on global insolation and characteristics of spectral solar radiation on a tilt surface; Zenten nissharyo ni motozuku zenten nissha supekutoru no suitei to keishamen bunko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Baba, H.; Kanayama, K.; Endo, N.; Koromohara, K.; Takayama, H. [Kitami Institute of Technology, Hokkaido (Japan)

    1996-10-27

    Use of global insolation for estimating the corresponding spectral distribution is proposed. Measurements of global insolation spectrum throughout a year were compiled for clear days and cloudy days, ranked by 100W/m{sup 2}, for the clarification of spectral distribution. Global insolation quantity for a clear day was subject mainly to sun elevation. The global insolation spectral distribution with the sun elevation not lower than 15{degree} was similar to Bird`s model. Under the cloudy sky, energy density was lower in the region of wavelengths longer than the peak wavelength of 0.46{mu}m, and the distribution curve was sharper than that under the clear sky. Values given by Bird`s model were larger than measured values in the wavelength range of 0.6-1.8{mu}m, which was attributed to absorption by vapor. From the standard spectral distribution charts for the clear sky and cloudy sky, and from the dimensionless spectral distributions obtained by dividing them by the peak values, spectral distributions could be estimated of insolation quantities for the clear sky, cloudy sky, etc. As for the characteristics of spectral solar radiation on a tilt surface obtained from Bird`s model, they agreed with actually measured values at an angle of inclination of 60{degree} or smaller. 6 refs., 10 figs., 1 tab.

  19. Development of air conditioning system using ecological shading window. Part 1. Characteristics of temperature transpiration rate on liana; Ecological shading window system no kaihatsu. 1. Tsuru shokubutsu no josan sokudo no ondo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Kudo, T.; Tanaka, H.; Tokunaga, M. [Kajima Corp., Tokyo (Japan)

    1994-10-31

    This paper summarizes an air conditioning system using an ecological shading window. The system uses plants in a double window in place of a blind to cut off sunlight, and operates the room air conditioning equipment combined with the plant utilization. Its features may be summarized as follows: perimeter cooling load in summer and perimeter heating load in winter can be reduced; and the plants purify the air in rooms, making clean humidification possible. Four kinds of liana were used to experiment the temperature characteristics of their transpiration. The transpiration rate, photosynthesizing rate and leaf temperature were measured, and the following findings were obtained: such plants that are adapted to weak light as philodendron and potos cannot control the leaf temperature under such a high illuminance and temperature as in the experimental condition, hence are not suitable for this system; and plants that have high transpiration rate under high temperatures such as ivy and cucumber can control the leaf temperature, performing photosynthesis stably, hence are suitable for the system. Insolation reducing effect was trially calculated. In the case of using ivy, the insolation can be cut down by 41% because of the transpiration cooling effect. 5 refs., 5 figs., 1 tab.

  20. Relationship between Vickers hardness and mechanical properties for austenitic stainless steels at cryogenic temperatures; Gokuteion ni okeru osutenaito kei sutenresu ko no bikkasu katasa to kikaiteki tokusei tono kankei

    Energy Technology Data Exchange (ETDEWEB)

    Iwabuchi, A.; Shimizu, T.; Onodera, R. [Iwate Univ., Iwate (Japan); Yoshino, Y.

    1999-11-10

    Of the material the hardness have be yield stress ductility-brittleness characteristics elastic recovery creep property contact electricity resistance frictional wear characteristics close. It is generally known that the following equation is established even in the inside between Vickers hardness and yield stress. However, whether it establishes this relation in the very low temperature has not clarified present place. Vickers hardness test was carried out at 293,77,4.2K each temperature of the tensile test in this study in very low temperature for the material. (NEDO)

  1. Analysis of the relationship between the coal properties and their liquefaction characteristics by using the coal data base; Tanshu data base ni yoru tanshitsu to ekika tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Kanbayashi, Y.; Okada, K. [Coal Mining Research Center, Tokyo (Japan)

    1996-10-28

    The relationship between coal properties and liquefaction or gasification characteristics was analyzed by using the analysis and test results and liquefaction characteristics in the coal data base. On liquefaction reaction, the close relation between an oil yield and coal constituent composition or a coal rank is well-known. Various multivariable regression analyses were conducted by using 6 factors as variables such as calorific value, volatile component, O/C and H/C atomic ratios, exinite+vitrinite content and vitrinite reflectance, and liquefaction characteristics as variate. On liquefaction characteristics, the oil yield of dehydrated and deashed coals, asphaltene yield, hydrogen consumption, produced water and gas quantities, and oil+asphaltene yield were predicted. The theoretical gasification efficiency of each specimen was calculated to evaluate the liquefaction reaction obtained. As a result, the oil yield increased with H/C atomic ratio, while the theoretical gasification efficiency increased with O/C atomic ratio. 5 figs., 1 tab.

  2. Effect of intermolecular cohesion on coal liquefaction. 3. Reactivity of oxygen methylated coal; Sekitan teibunshika hanno ni okeru bunshikan gyoshuryoku no koka. 3. O-methyl ka tan no hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, M.; Nagaishi, H.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    The reactivity of oxygen methylated coal was studied to control hydrogen bond in bituminous coal liquefaction and intermolecular cohesion such as van der Waals force. In experiment, crushed and dried Illinois coal of 100mesh or less was used as specimen, and oxygen methylated coal was prepared by Liotta`s method using tetrabutylammonium halide. Coal liquefaction was conducted in an electromagnetic agitation autoclave using tetralin solvent under initial hydrogen pressure of 100kg/cm{sup 2} while heating. The molecular weight distribution of the products obtained was measured by gel permeation chromatography (GPC) analysis. The experimental results are as follows. The effect of intermolecular cohesion in bituminous coal on the reactivity is mainly derived from decomposing reaction from preasphaltene to oil. Yields of oil fraction by methylation increase corresponding to release of intermolecular cohesion. Since the thermal release is promoted with temperature rise, the difference in yield due to different treatments decreases. 5 refs., 3 figs., 1 tab.

  3. Effect of coal rank and mineral matter on gasification reactivity of coal char treated at high temperature; Netsushorishita sekitan char no gas ka tokusei ni taisuru tanshu oyobi kobutsushitsu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Morishita, K.; Takei, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

    1996-10-28

    In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks depends on the temperature of heat treatment, and the lower the heat treatment temperature is, the more largely the gasification rate is influenced by catalysis of mineral matters included in the coal. As causes of the decrease in gasification rate associated with the rise in temperature of heat treatment, indicated were release of alkali metal having catalysis and decrease of active sites by carbonaceous crystallinity. 6 figs.

  4. Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Seo, K.; Yamanaka, H. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-05-27

    The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

  5. Effects of short fiber reinforcement and mean stress on tensile fatigue strength characteristics of polyethersulfone; Tansen`i kyoka porieterusaruhon no hippari hiro tokusei ni oyobosu heikin oryoku no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Furue, H.; Nonaka, K. [Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan)

    1996-01-15

    Thermoplastics are often reinforced with short fibers with aims of improvement of their strengths, rigidities and hardness or maintenance of their dimensional stabilities. Such short fiber reinforced plastic materials have more expectation for high performance plastics. Authors already examined of some effects of reinforced fiber and of orientation in injection molding on flexural fatigue characteristics of the injection-molded high performance thermoplastic materials. However, the examination of short fiber reinforced effects on fatigue strength characteristics was not always sufficient. In this study, in order to obtain a guiding principle for fatigue resistant design of the short fiber reinforced injection molding materials, polyethersulfones (PES) was examined on its tensile fatigue strength and an effect of short fiber reinforcement for improvement of its fundamental dynamic properties on its fatigue characteristics. Especially, its fatigue life characteristics was elucidated mainly on relationship of mean stress, stress amplitude and number of repeating fracture in tensile fatigue behavior. 10 refs., 15 figs., 2 tabs.

  6. 3Wave propagation in rock samples under medium and low temperature conditions. Characteristics of methane hydrate-BSR phenomena; Chu teion ryoiki ni okeru ganseki shiryo no hado denpa tokusei. 1. Methane hydrate BSR gensho no kosatsu suitei

    Energy Technology Data Exchange (ETDEWEB)

    Rokugawa, S.; Kato, Y.; Matsushima, J.; Sano, A. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-10-22

    In relation to sea-bottom pseudo reflection face and methane hydrate in seismic exploration records, fundamental experimental studies have been made. In order to get a handhold to elucidate phenomena accompanying methane hydrate, the studies have investigated wave propagation behavior of rock samples and sandy sediments under medium and low temperature conditions. The experiments have used a constant-temperature cooling water circulating equipment to control temperatures of each sample. The samples were placed in a cooler box with the vibration transmitter and receiver fixedly installed, and changes of the waves against temperature change were measured. Sand-stones and two kinds of tuffs were used as rock samples for the measurement. Artificial sand sample soaked in water was used as a substitute for a methane hydrate layer. As a result of the experiments, the relation between the hydrate layer and the gas layer was comprehended. In addition, the blanking phenomenon was thought occurring as a result of the nearly whole substance presenting the speed of ice due to freezing of the sediments, rather than by what is described in the ground homogeneousness theory. 5 refs., 9 figs.

  7. Strength evaluation for modified 12Cr steel and A286 steel of USC turbine rotor material. Chocho rinkaiatsu turbine rotorzai kairyo 12Cr ko oyobi A286 ko no kyodo tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, Takashi; Nitta, Akito.; (Central Research Inst. of Electric Power Industry, Tokyo, Japan)

    1990-01-01

    For candidate materials of the ultra super critical (USC) turbine rotor in a coal fired power plant, the modified 12Cr steel and A286 steel are subjects of the study under the first step steam condition (316 atg, 593 centigrade) and under the second step steam condition (350 atg, 650 centigrade), respectively. The strength evaluation tests of the modified 12Cr steel untreated material and aging (630 centigrade, 4860 hours) material I were conducted previously, and obtained a prospect that the material can be applied to the first step turbine rotor. In this report, the strength evaluation tests and microstructure observation of the long period aging (630 centigrade, 8190 hours) material II, and the strength tests of the A286 steel have been conducted. As a result, it was found that the modified 12Cr steel is a stable material in the microstructure and has enough strength characteristics to apply the first step rotor, and the A286 steel also can be applied to the second step rotor. 9 refs., 27 figs., 8 tabs.

  8. Thermoelectric characteristics of iron silicide thermoelectric converter with the transition metallic compound as an additive; Sen`i kinzoku kagobutsu wo tenkabutsu to shita keikatetsu netsuden soshi no netsuden tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hayashibara, M.; Oda, M. [Hitachi, Ltd., Tokyo (Japan)

    1994-04-13

    The thin film must be converted into a bulky shape in order that the high electric power may be produced by the iron silicide thermoelectric converter. Study was then made to establish the homogeneous bulk production method, in which the additive must diffuse sufficiently in the iron silicide and bond strongly to it during the sintering. Selected as an additive in the present study, Co compounds were all decomposed below the sintering temperature and remained in the iron silicide. The Co sulfide, phosphide, bromide and iodide were particularly high in reactivity with the iron silicide. The Co, of which the added quantity was proportional to the electric conductivity, was almost homogenized into a solid solution. In the experiment, both Co sulfide and phosphide were equal in thermoelectric power as an additive. The Co bromide and iodide were maximally about 10% and 50%, respectively lower in thermoelectric power than the Co sulfide. It is attributable to the FeSi2 reformed to the electrically insulating SiO2 and low-thermoelectric power FeSi, because both Co bromide and iodide are oxidizing compounds. 7 refs., 10 figs.

  9. Changes of the temperature coefficients of the characteristics which accompany degradation and recovery of a-Si solar cells; A-Si taiyo denchi no hikari (denryu) rekka oyobi kaifuku ni tomonau tokusei ondo keisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Yanagisawa, T.; Koyanagi, T.; Nakamura, K.; Takahisa, K.; Kojima, T. [electrotechnical Laboratory, Tsukuba (Japan)

    1996-10-27

    Pursuant to the measuring of temperature dependency of the characteristics such as conversion efficiency, during the process of degradation in a-Si solar cells due to light and electric current and the process of recovery by annealing, this paper describes changes in temperature coefficients, correlation between the characteristic parameters and the degradation, and the results of the examination of their characteristics. The conversion efficiency {mu} degraded approximately by 45% of the initial value each by the irradiation under a light intensity with 3 SUN accelerated and by the infusion of current at 20mA/cm{sup 2}; and then, the efficiency recovered to 70-75% of the degradation by subsequent annealing. In addition, in the temperature dependency at 80{degree}C against at 20{degree}C, Isc slightly increased while Vcc greatly decreased. This slight increase in Isc was mainly due to the decrease in the width of the forbidden band, while the decrease in Vcc was due to the increase in the reverse saturation current. The temperature dependency of {mu}N was negative, becoming small in accordance with the degradation. The temperature dependency of FF/FFO was negative initially both in light and current, but it decreased with the degradation and turned to positive. The temperature coefficients of I-V parameters reversibly changed corresponding to the degradation and recovery of these parameters and stayed in a good correlation. 7 refs., 8 figs., 1 tab.

  10. Model experiment on change of seismic properties of a fracture caused by injecting/draining water; Chusui/haisui ni yoru kison kiretsu no dansei denpa tokusei no henka ni kansuru model jikken

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Koizumi, T.; Sassa, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1997-05-27

    Effect of water injection/draining on elastic waves penetrating through cracks is examined by measuring elastic waves before, during, and after the injection/draining of water into/from cracks in presence in granite. Two blocks of rock, with their crack-containing surfaces in contact with each other, are placed in a vessel, and water injection/draining is done through a hole on a vessel bottom side so that water will penetrate into the cracks. When the blocks are dry, there is almost no contact between the cracks, and so no crack penetrating waves are observed. Crack penetrating waves are produced when water is injected, and the position of the receiver sensing the penetrating waves changes as the water level rises. When the water level is lowered from the high water level, the waveform changes again as the level changes. The change in waveform is not so remarkable, however, as that observed during water injection thanks to the water residual in the cracks. It is now inferred that crack investigation is more effective when it is carried out with water being injected into dry cracks. The difference produced between the dry state and wet state when water is injected into dry cracks is used to detect the presence of cracks in this experiment, and this may be applied also to the investigation of cracks in the shallow part of the ground. 4 refs., 11 figs.

  11. Aliasing characteristics of tau-P transform and is application to signal and noise separation; Tau-P henkan no aliasing tokusei to hakei iji wo koryoshita S/N bunri

    Energy Technology Data Exchange (ETDEWEB)

    Kawabuchi, H.; Rokugawa, S.; Matsushima, J.; Ichie, Y. [The University of Tokyo, Tokyo (Japan); Minegishi, M.; Tsuburaya, Y. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    With respect to the tau-P transform method as a signal and noise (S/N) separation technology used in seismic exploration using the reflection method, a discussion has been given on conditions for the post S/N separation by the tau-P transform to function more effectively. Averaging the energy in performing the tau-P transform makes the wave energy scatter to a certain range. As a result, an aliasing phenomenon appears, in which noise is superimposed on the post-processing record. As a result of the discussion, it was verified that satisfying the two equations of G. Turner is effective in order to reduce the aliasing and maintain the relative amplitude. However, in actual calculation accuracy, waveform change was recognized to some extent, particularly amplification of events in low frequencies, and low restorability in higher frequencies. It was also observed that a method to give the tau-P region a two-dimensional Fourier transform and perform the same processing as an f-k filter can remove aliasing more simply and effectively than the HVF, and improve the S/N ratio maintaining the amplitude at the current level. 5 refs., 13 figs.

  12. Effects of barrier on creeping discharge characteristics in SF6 and N2 Gases under pulse voltages; SF6 oyobi N2 gas chu no pulse den`atsu ni yoru enmen hoden tokusei ni oyobosu barrier no koka

    Energy Technology Data Exchange (ETDEWEB)

    Watabe, K.; Kamatani, H.; Kobayashi, N.; Onoda, M.; Nakayama, H. [Himeji Inst. of Tech., Hyogo (Japan)

    1997-10-20

    This paper describes the effect of barrier upon creeping discharge characteristics in SF6, N2 and their mixture. The barrier height effect on the discharge voltage was investigated under the positive pulse voltage. The discharge voltage increased as increasing the barrier height in SF6 gas. On the other hand, the discharge voltage hardly changed with the barrier height in N2 gas. In order to make clear the mechanism of the initial creeping corona, it was observed with the optical technique such as ultra-high speed electronic imaging system (IMACON 468). As the result, creeping corona path revealed the difference in images under various barrier height. And the charge accumulated on the barrier induced with the initial corona in SF6 gas could suppress the development of the later creeping corona in contrast with N2 gas. 19 refs., 7 figs.

  13. Study on characteristics and effecting factors of nitrification in media-added activated sludge process; Tantai tonyugata kassei odeiho no shoka tokusei to sono eikyo inshi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Mishima, K. [Ebara Corp., Tokyo (Japan); Nishimura, T. [Kawasaki City Office, Kawasaki (Japan); Fujita, M. [Osaka University, Osaka (Japan). Faculty of Engineering

    1998-04-10

    The characteristics and the effecting factors of the nitrification in the media-added activated sludge process (M-AS) were studied using pilot-plants. The hydrophilic gels and sponges were used as the adhesion media for microorganisms. The nitrification rate of the hydrophilic gels showed 60-109 g-N/m{sup 3}-media/h{sup 1}, and the concentration of the attached microorganisms on the media were 1,500-6,900 mg/l{sup 1} as MLSS in the bioreactor. Although the MLSS of the sponges was approximately equivalent to that of the hydrophilic gels, the nitrification rates of the sponges were lower than those of the hydrophilic gels because the principal place for the growth of the nitrifier was considered as the outer surface of the sponges. The media nitrification rate increased in proportion to the increase of the adhesion area of the added media. The DO dependency of the media nitrification was higher than that of the suspended activated sludge. The specific nitrification rate of the attached microorganisms showed 4-5 times higher than that of the suspended activated sludge. The authors considered that this was caused by the low BOD/NH3-H ratio of the bioreactor influent. 11 refs., 12 figs., 3 tabs.

  14. On the approximation with Chebyshev`s Q-function to ABR waveform and the estimation of its characteristics; Chebyshev q kansu ni yoru ABR hakei kinji to tokusei suitei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ikawa, N.; Kurata, T. [Chiba University, Chiba (Japan); Kato, S. [Teikyo Heisei University, Tokyo (Japan); Aruga, M. [Tokai University, Tokai (Japan)

    1998-10-01

    It is well known that ABR (Auditory Brainstem Responses) waveforms are used when the judge of the brain death or the check of some hearing troubles and so on are needed. The physiological side of this responses is nearly made clear, but the systematic mechanism of them is not investigated sufficiently. Therefore the quantitative estimation of those systematic mechanism is not yet obtained sufficiently. In this paper, firstly the polynomial approximation results of the entire ABR waveform are shown by using the Chebyshev`s q-function. Secondarily the tendency of the latency (a parameter of ABR) is considered and compared with the experimental formula which was independently derived from the another data and analysis. Through these discussion it was shown that the indices of the quantitative analysis of characteristics of ABR parameters were given as the polynomial approximate functions of the use of the approximate method applying the Chebyshev`s q-function. 6 refs., 1 figs., 2 tabs.

  15. Fiscal 1999 research result report. Research on improvement of boiling heat transfer characteristics by photocatalyst wall; 1999 nendo hikari shokubai hekimen ni yoru futto netsu dentatsu tokusei kaizen ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research was made on improvement of the wettability and boiling heat transfer characteristics of a photocatalyst wall. Measurement experiment of the wettability was made for anatase type titan oxide-coated Al, SUS and Pb plates, rutil type titan oxide-flame coated SUS plate, raw plate, and oxide-plasma coated titan plate. In the ground experiment, the contact angles of distilled water and oil on specimen surfaces were measured. In the microgravity experiment, falling droplet images were recorded by using the facility of Japan Microgravity Center (JAMIC). For obtaining the effect of radioactive emission, UV irradiation, {gamma} ray and neutron beam irradiation by nuclear reactor, and {gamma} ray irradiation by Co-60 were carried out. As the experiment result, the rutil type titan oxide-flame coated SUS plate, nonconductor-coated titan plate, and zircaloy plate showed large improvement of the wettability by {gamma} ray irradiation with Co-60. It was also confirmed that in particular, titan shows the large effect of radioactive emission, and the wettability deteriorates rapidly after {gamma} ray irradiation. (NEDO)

  16. Improvement of the characteristics of a diagonal-flow fan in low flow range with casing-bleed-holes; Keshingu kiko ni yoru sharyu sofuki no teiryu ryoiki tokusei no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Yoichi; Sasaki, Kazuto; Yamaguchi, Sumio; Yamashita, Shoji; Shimada, Taichiro

    1999-09-01

    Generally, a high specific speed diagonal flow fan with a small pressure rise coefficient has a slight positive gradient part of the pressure rise - flow rate characteristics. In addition, the pressure fall is small, between the flow rate at which the impeller stall in the throttle closer and the stalling flow rate. In the case, Kaneko et al. suggest a way of improvement on performance characteristics by an inlet annular wing which removes a low-momentum fluid from a rotor tip region. However, in case of a fan that has a sharp drop of pressure rise in the stall characteristics, it is not clear that the stall characteristics can be improved by this way. In this study, in order to improve the unstable characteristics of a high pressure rise coefficient diagonal flow fan, Tip clearance flow has been investigated on five rotor-casings with various holes to bleed low-momentum fluid in the range of flow rate from design point to stall point. (author)

  17. Improvement of low temperature oxidation resistance in MoSi{sub 2}-oxides composites; Sankabutsu no fukugoka ni yoru MoSi{sub 2} zairyo no teion sanka tokusei no kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, W.; Uchiyama, T. [Riken Corp., Saitama (Japan)

    1999-11-15

    MoSi{sub 2}-oxides composites using fine aluminosilicate powder (< 0.2{mu}m) have demonstrated excellent low temperature oxidation resistance and thermal shock resistance. These properties strongly depend on microstructural morphology and are obtained in composites that network-structures of both phases of MoSi{sub 2} and oxides are developed, i.e., in composites with oxides of 20 {approx} 40 vol. %. When one phase is independently dispersed in the other phase, on the other hand, problems of low temperature oxidation and thermal shock occur. The low temperature oxidation problem occurs in the composites with oxides less than 15 vol. % and the thermal shock problem occurs in the composites with oxides more than 50 vol. %. These results will contribute to material design approaches for high temperature structural applications of MoSi{sub 2}. (author)

  18. Heat and fluid flow properties of circular impinging jet with a low nozzle to plate spacing. Improvement by nothched nozzle; Nozzle heibankan kyori ga chiisai baai no enkei shototsu funryu no ryudo dennetsu tokusei. Kirikaki nozzle ni yoru kaizen kojo

    Energy Technology Data Exchange (ETDEWEB)

    Shakouchih, T. [Mie University, Mie (Japan). Faculty of Engineering; Matsumoto, A.; Watanabe, A.

    2000-10-25

    It is well known that as decreasing the nozzle to plate spacing considerably the heat transfer coefficient of circular impinging jet, which impinges to the plate normally, increases remarkably. At that time, the flow resistance of nozzle-plate system also increases rapidly. In this study, in order to reduce the flow resistance and to enhance the heat transfer coefficient of the circular impinging jet with a considerably low nozzle to plate spacing, a special nozzle with notches is proposed, and considerable improvement of the flow and heat transfer properties are shown. The mechanism of enhancement of the heat transfer properties is also discussed. (author)

  19. Spray characteristics of dimethyl ether (D.M.E.) as on alternative fuel for diesel engine; Daitai diesel nenryo to shite no dimethyl ether (D.M.E.) no funmu tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, K.; Nishida, K.; Yoshizaki, T.; Hiroyasu, H. [Hiroshima University, Hiroshima (Japan)

    1997-10-01

    D.M.E. which was paid attention to as on alternative fuel for a diesel engine, was injected by using Bosch type injection pump and a hole nozzle into a high pressure and high temperature vessel. The spray was observed by using schlieren photography. Spray characteristics, such as, the tip penetration, the cone angle and the volume of the spray were and were compared with a diesel fuel spray. The following thing, and so on were found out as a results. The spray angle of the DME spray of atmosphere pressure Pa=0.1Mpa spreads out large in comparison with the diesel fuel spray, and the way of the change by the pressure is contrary to the case of the diesel fuel spray. 3 refs., 6 figs., 1 tab.

  20. Three-dimensional analysis of internal flow characteristics in the injection nozzle tip of direct-injection diesel engines; Sanjigen suchi kaiseki ni yoru DI diesel kikan no nenryo funsha nozzle nai ryudo tokusei no kaimei

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, H.; Matsui, Y.; Kimura, S. [Nissan Motor Co. Ltd. Tokyo (Japan)

    1997-10-01

    To reduce the exhaust emissions and fuel consumption of direct-injection diesel engines, it is essential to optimize the fuel injection equipment closely related to combustion and emission characteristics. In this study, three-dimensional computation has been applied to investigate the effects of the injection nozzle specifications (e.g., sac volume, round shape at the inlet of the nozzle hole) and needle tip deviation on internal flow characteristics. The computational results revealed that the effects of the nozzle specifications and needle tip deviation with a smaller needle lift on internal flow characteristics and a general approach to optimize the injection nozzle specifications were obtained. 3 refs., 10 figs., 1 tab.

  1. Injection and spray characteristics of a variable orifice nozzle applied the jerk type fuel injection pump for DI diesel engine; Jerk shiki nenryo funsha pump wo mochiita kahen funko nozzle no funsha funmu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T.; Matsui, K.; Iwasaki, T.; Kobayashi, T. [Zexel Corp., Tokyo (Japan); Matsumoto, Y. [The University of Tokyo, Tokyo (Japan)

    1997-10-01

    A Variable Orifice Nozzle (VON) by changing a cross-sectional area of the nozzle injection hole, for improving a rate of injection and injection duration, has been developed to study its injection and spray characteristics. The nozzle geometry was optimized to analyze a nozzle internal flow by computational method. Results show that, injection and spray pattern responded to the nozzle orifice cross-sectional area which is changing larger to smaller in the part load range. This results suggest to contribute a combustion improvement which decreasing NOx and soot. 14 refs., 10 figs.

  2. Experimental consideration on the contact resistance caused by the distribution of contact spots with the contact model using electrolyte bath; Denkai yokuso wo mochiita sesshoku model ni yoru sesshokuten no bunpu to sesshoku teiko tokusei ni kansuru jikkenteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Aichi, H. [Daido Institute of Technology, Aichi (Japan); Miyachi, I. [Aichi Institute of Technology, Aichi (Japan)

    1996-09-20

    Electric contact members are classified by the form such as a point, a line, and a plane. Particularly, the point contact member which makes a small circular contact spot is basis of the contact form. Also, the plane contact member will make many contact spots which are different in size and distributing over the contacting portion. Authors have been developing the contact model to measure the contact resistance. In this model, it is available to select the size, the number, and the arrangement of contact spots by the macroscopical contact spots which are formed with some metal electrodes arranged in electrolyte solution of dilute sulfuric acid. In this paper, the fundamental characteristics of the contact resistance caused by the construction of current are investigated with 1 to 3 contact spot models. Then the relations between the contact resistance and the distribution of the contact spots are examined with 2 to 9 multi-contact spot models. As the results, it is cleared that the proposed contact model presents the successful experimental method for the analysis of the contact resistance. 9 refs., 8 tabs.

  3. Control of a jet impinging on a wedge having a circular cylinder at the vertex. Mean flow and turbulence properties; Sentan enchu ni yoru kusabimen shototsu funryu no seigyo. Heikinryu to midare no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, H.; Matsuda, K. [Daido Institute of Technology, Nagoya (Japan); Nakamura, I. [Nagoya University, Nagoya (Japan). Faculty of Engineering

    1995-07-25

    An experimental study has been performed on the mean flow and turbulence properties of a two-dimensional jet impinging on a wedge having a circular cylinder with various diameters at the wedge vertex. The nondimensional profiles of the mean velocity in the fully developed flow region of the wall jet approach those of the conventional two-dimensional wall jet when a cylinder is attached to the wedge vertex and if the cylinder diameter is increased. Also both the slopes of the growth of the half-width and of the decay of the maximum velocity approach these of the two-dimensional case. The non-dimensional profiles of the turbulence intensities and of Reynolds stress in the fully developed flow region of the wall jet behave in the same manner, as mentioned above. In the variations along the wall of the integral value of the total production term of Reynolds stress, there exists the negative value region of it near the wedge vertex, and it extends as the cylinder diameter increases. 21 refs., 16 figs.

  4. Experiments on the turbulent boundary layer on a thin cylinder rotating in an axial flow. 1st Report. Properties of mean flow and turbulence; Jikuryuchu no hosonaga kaiten entojo no ranryu kyokaiso no jikken. 1. Heikinryu to nagare no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yano, H. [Daido Institute of Technology, Nagoya (Japan); Yamashita, S.; Naruse, Y.; Kondo, K. [Gifu University, Gifu (Japan). Faculty of Engineering

    1996-09-25

    The mean velocity and turbulent field in a three-dimensional turbulent boundary layer on a thin cylinder rotating in a uniform stream are examined experimentally. Measurements of mean velocity and all Reynolds stresses are made by means of a single rotatable hot-wire method. Mean velocity distribution is well represented in the relative main flow direction with respect to the rotating cylinder by a logarithmic law deduced in an earlier study. Johnston`s logarithmic law for 3-D turbulent boundary layers also accurately describes the present flow. Although turbulent intensities and Reynolds stresses all increased with rotation speed of the cylinder, their distributions are well represented by non-dimensionalization using the resultant velocity of the main flow and the peripheral velocity of the cylinder. Both eddy viscosities and mixing lengths increase with the rotation speed, and there is no evidence of isotropic eddy viscosity. 21 refs., 15 figs., 1 tab.

  5. Influence of the added oxide power on the magnetic property of the iron-chromium magnetic sintered alloy in alternating field; FeCr kei shoketsu jisei gokin no koryu jiki tokusei ni oyobosu sakabutsu funmatsu tenka no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kato, T.; Kanazawa, H. [Daido Institute of Technology, Nagoya (Japan); Kawamura, M.; Kono, T.; Kusaka, K. [Daido Steel Co., Nagoya (Japan)

    1994-07-15

    This paper describes effects of addition of mixed oxide powder on the magnetic properties of low carbon Fe-13Cr-0.8Si sintered alloy. The mixed powder composed of SiO2, CaO, and Al2O3 was added. It was found that the magnetic characteristics of specimens in direct magnetic field degraded with addition of oxide powder. However, they were improved with rising the sintering temperature. On the other hand, the amplitude relative permeability of specimens in alternating magnetic field was higher in the case of 0.1 to 0.2% addition of oxide powder than no addition one. The relative permeability showed a change of increase and then decrease with rising the sintering temperature. However, it was found that the proportion of the decrease in relative permeability at the higher sintering temperature was restrained by addition of the oxide powder. These phenomena were discussed in relation to sintered density, porosity, and electrical resistivity. 8 refs., 13 figs., 2 tabs.

  6. Characteristics of contact resistance for Ag, Cu and Al spot contact under DC current flow of 300A; Gin, do oyobi arumi tensesshokushi no chokuryu 300A tsudenji ni okeru sesshoku teiko tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Aichi, H. [Daido Institute of Technology, Nagoya (Japan); Matsumura, T. [Nagoya University, Nagoya (Japan); Miyachi, I. [Aichi Inst. of Technology, Aichi (Japan)

    1997-07-01

    The temperature rise of the contact spot by Joule`s heat under high current flow may result in the softening or welding of the contact materials. Contact resistances of Ag, Cu and Al spot contacts have been observed under the current flow of up to 300A DC. The contact resistances of Ag and Cu with clean surfaces were revealed to be kept constant independent of the magnitude of the applied current flow. On the other hand, contact resistances of Al and Cu with oxidized surfaces were greatly reduced with the increasing current flow. 7 refs., 5 figs., 2 tabs.

  7. Tensile properties and cyto-toxicity of new biomedical {beta}-type titanium alloys; Atarashii seitaiyo {beta}gata chitan gokin no sekkei to sono kikaiteki tokusei oyobi saibo dokusei

    Energy Technology Data Exchange (ETDEWEB)

    Kuroda, D.; Niinomi, M. [Toyohashi University of Technology, Aichi (Japan); Fukui, H. [Aichi Gakuin University, Aichi (Japan). School of Dentistry; Morinaga, M. [Nagoya University, Nagoya (Japan); Suzuki, A. [Daido Steel Co. Ltd., Nagoya (Japan)

    2000-09-01

    Co-Cr alloy, SUS 316L stainless steel, pure Ti and Ti-6Al-4V ELI have been used as implant materials. Ti-6Al-4V ELI has been most widely used as an implant material to date because of its excellent combination of biocompatibility, corrosion resistance and mechanical properties. Since toxicity of V etc., and high moduli of elasticity have been pointed out, {beta}-type biomedical titanium alloys are recently getting much attentions, New {beta}-type biomedical titanium alloys composed of non-toxic elements such as Nb, Ta, Mo, Zr and Sn with lower moduli of elasticity and greater strength were, therefore, designed using alloy design method based on the d-electron theory in this study. Tensile test, measurement of modulus of elasticity and evaluation of biocompatibility were conducted in order to investigate the mechanical properties and biocompatibility of the designed alloy. Tensile strength and elongation of Ti-29Nb-13Ta-4.6Zr are, in particular, equivalent to those of conventional biomedical titanium alloy such as Ti-6Al-4V ELI, and modulus of elasticity of Ti-29Nb-13Ta-4.6Zr is lower than that of Ti-6Al-4V ELI. The moduli of elasticity of the designed alloys are equivalent or lower comparing with those of conventional biomedical titanium alloys such as Ti-6Al-4V ELI and Ti-13Nb--13Zr. The biocomparibility of Ti-29Nb-13Ta-4.6Zr is equivalent to pure-Ti, and biocompatibility of Ti-29Nb-13Ta-4.6Zr is much greater than that of Ti-6Al-4V. The new {beta}-type titanium alloy, Ti-Nb-Ta-Zr, designed in this study is expected to have greater performance for implant materials. (author)

  8. Experiments on the injection of a circular jet into a wake of an airfoil. Mean flow properties; Tsubasa no koryuchu ni fukidasareru enkei funryu ni kansuru jikken. Heikinryu no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, H.; Komori, N. [Daido Institute of Technology, Nagoya (Japan); Nakamura, I. [Nagoya University, Nagoya (Japan). Faculty of Engineering

    1995-01-25

    This paper reports the result obtained when a circular jet was injected into a wake of a two-dimensional symmetrical airfoil in a uniform air current and when the three-dimensional mixing process in the jet was examined. In these experiments, the attack angle ({alpha}) of the airfoil was set to 0{degree} and 5{degree}, and the circular jet was injected from near the trailing edge of the airfoil to the airfoil surface. The relative velocity distribution of the mean jet velocity to the wake is axisymmetric and almost coincides with the Gaussian distribution (reported by Mr. Ishigaki) for a two-dimensional free jet. The maximum relative velocity of the jet and the state of attenuation vary depending on the ambient wake field. In relative velocity distribution, the half-value width in the Y direction (perpendicular to the uniform flow direction and airfoil width direction) and Z direction (perpendicular to the uniform flow direction and Y direction) has hardly any difference when {alpha} is 0{degree}. The half-value width in the Z direction is slightly higher than that in the Y direction when {alpha} is 5{degree}. In this case, the jet is extended near the center in the Z direction. 15 refs., 14 figs.

  9. Research and development of photovoltaic power system. Study of carrier dynamics in a-Si from optical and optoelectronic properties; Taiyoko hatsuden system no kenky kaihatsu. Amorphous silicon no koden tokusei to sono carrier dynamics no kogakuteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hamakawa, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on an optical study of optoelectronic properties of amorphous silicon and its carrier dynamics. Studies have been performed on elucidation of the optoelectronic conversion mechanism in an a-Si film p-i-n junction system and the relationship of the mechanism with the optoelectronic properties. In the studies, optically induced defect level distribution was evaluated by using the modulated optical current spectroscopy, and confirmation was made on model forecast and qualitative agreement, such as large increase in neutral defect levels in association with beam irradiation. In research on elucidation of a film forming mechanism for a-Si based alloys, and material property control, a high-sensitivity reflective infrared spectroscopy was used to observe mechanisms such as treatments and processes given in device fabrication. In research on optical and optoelectronic properties of an s-Si alloy thin film by using the modulated spectroscopy, a new evaluation technology dealing with amorphous semiconductors was developed. The technology separately evaluates carrier migration factors of electrons and holes by combining polarization angle dependence of electro-absorption signals with hole migration measurements. 4 figs.

  10. Thermal infrared spectra of surface rocks. Comparison of in the laboratory, in situ, and remote sensing data; Chihyo ganseki no netsusekigaiiki bunko tokusei. Chijo sokutei data to remote sensing data no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Ninomiya, Y.; Matsunaga, T. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    An ASTER (advanced spaceborne thermal emission and reflection radiometer) is one of the image sensors. It is to be installed in an earth survey polar orbit platform satellite, EOS-AM1, which is to be launched in 1998, and it is going to start its operation. Data observed by the thermal infrared remote sensing of ASTER include the spectral emissivity, and the spectral emission reflectivity which is expressed by the function of temperature. It is required to overcome technical problems how to extract the spectral emissivity from the observed data. The spectral emissivity extracted from the remote sensing data by the MMD method, measured for samples collected in Cuprite area, Nevada, and/or measured at sampled points were compared to each other and discussed. The hemisphere spectral reflectivity, which is indirect spectral emissivity, agreed well with the direct spectral emissivity. Data suggesting the establishment of Kirchhoff`s law were obtained even for the weathered samples. The spectral emissivity derived from the remote sensing data by the MMD method was in harmony with the spectral characteristics measured strictly on the ground. 14 refs., 3 figs.

  11. Degradation characteristics of total organic carbon in UV-C oxidation pilot plant accompanied by hydogen peroxide addition; Kasanka suiso heiyo UV-C sanka pairotto puranto ni okeru zen yukitai tanso bunkai tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamakoshi, Y. [Photoscience Japan Corp., Tokyo (Japan); Sugawara, K.; Sugawara, T. [Akita Univ., Akita (Japan). Mining College

    1997-03-10

    Degradation characteristics of total organic carbon (TOC) for the dilute water of super LSI cleaning waste water used in semiconductor factory was studied by pilot plant experiment using low pressure mercury lamp and UV-C oxidation accompanied by hydrogen peroxide method. Firstly, decomposition rates of methanol, acetone and isopropyl alcohol (IPA) were compared. As a result, the initial TOC concentration of each organic compound was 1mg-C.l{sup -1}, and decomposition rate of methanol was most faster and acetone and IPA showed almost same rates at a condition of initial concentration of 10 ppm of hydrogen peroxide. Secondly, experiment using different light intensity lamps was carried out in order to study the effect of light intensity on TOC decomposition rate. As a result, it was revealed that the decomposition constant was proportional to the light intensity. Further, from the experiment with different number of lamps that are on, it was clarified that the effect of inner filter due to hydrogen peroxide differed when lamp density inside the same reactor was different. 7 refs., 8 figs.

  12. Study of an optimization of regeneration for an absorbent used in the solar desiccant cooling system; Taiyonetsu riyo desiccant reibo ni mochiirareru kyushuzai saisei tokusei no saitekika ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y. [Osaka Institute of Technology, Osaka (Japan)

    1997-11-25

    A desiccant cooling system uses concentrated aqueous solution of an absorbent to reduce humidity, hence the resultant absorbent solution becomes dilute. Regeneration of the dilute solution uses solar heat, where the regeneration characteristics are affected by solution temperature, vapor pressure, water content, air-liquid flow rate, and other factors. Therefore, mutual relationship among these different factors were investigated, and an optimum operating condition was discussed. The regeneration characteristics of the absorbent is strongly affected by temperature of triethylene glycol (TEG). This is because vapor pressure, Ps, in the TEG aqueous solution increases as the TEG temperature rises. This means that preheating the solution is effective in regenerating the absorbent. As the regeneration progresses, the water content, Ww, decreases, and the regeneration rate decreases. This is because of reduction in the Ps in association with decrease in the Ww of the TEG. This suggests that it is important in the absorbent regeneration to reduce flow rate of the TEG aqueous solution as low as possible. Raised air temperature reduces difference in vapor partial pressure between the TEG and the air, resulting in reduced regeneration rate. 5 refs., 9 figs.

  13. Fundamental study on hydrogen storage with hydrogen absorbing alloys. Operating characteristics of storage tank; Suiso kyuzo gokin wo mochiita suiso chozo ni kansuru kiso kenkyu. Chozo yoki no dosa tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sekiguchi, S.; Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Hydrogen absorption by a hydrogen storage (MH storage) is investigated for static characteristics, with a constant current applied to the hydrogen generator, and dynamic characteristics, with a fluctuating current applied to the same simulating actual insolation. In the experiment, alloy temperature (MH temperature) in the storage and a current for the generator are preset, and then automatic measurement is allowed to proceed at 10-second intervals of the differential pressure, hydrogen temperature in the piping, absolute pressure, MH temperature, room temperature, and water tank temperature. It is found as the result of the experiment that absorption performance is improved when the MH storage is cooled; that the mean absorption rate which is 1 without cooling increases to 1.62 at 7degC; that the mean absorption rate changes in proportion to the applied current (introduced hydrogen flow rate); that the rate which is 1 at 32A decreases to 0.53 that at 16A; that the absorption rate is dependent more on the current applied to the storage than the temperature of the heat exchanging medium; and that, even in the presence of fluctuation halfway in the applied current, the total absorption will be equal to a case of constant current application if the total amount of applied current is equal. 2 refs., 7 figs., 5 tabs.

  14. Output characteristic of photovoltaic module on different installing conditions. Comparison with calculated value and measured value; Secchi joken no kotonaru taiyo denchi module no shutsuryoku tokusei. Suchi kaiseki to jissokuchi tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, T.; Morita, Y.; Iwawaki, H.; Fujisawa, T.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    The paper studied output characteristics of photovoltaic modules different in installation conditions on the basis of the energy balance state. In the study, an energy balance equation was constructed for insolation intensity, heat losses from PV surface/back, and output, in order to calculate cell temperatures in each installation condition. A comparative study was made between calculated results and measured data obtained on the top of the school building. The results indicated the following: The thickness of thermal boundary layer became approximately 27mm at insolation intensity of 800 W/m{sup 2}, ambient air temperature of 25degC, and wind velocity of 0.5m/s. When widening air gap from 20mm to 40mm, the cell temperature decreased 4degC, and the output increased 1.6%. In the case of installing photovoltaic modules on the roof considering the relation between the air gap in the heat balance state and the thickness of thermal boundary layer, heat from PV back was released outside the air gap if widening the air gap to more than 30-40mm. The type with a heat insulating material on the panel back decreased in output from other types. 5 refs., 7 figs., 4 tabs.

  15. Non-contact evaluation of mechanical properties of electroplated wear resistant Ni-P layer from the velocity dispersion of laser SAW; Laser reiki Rayleigh ha no sokudo bunsan wo mochiita taimamo Ni-P mekkiso tokusei no hisesshoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Morikawa, Y.; Cho, H.; Takemoto, M. [Aoyama Gakuin University, Tokyo (Japan). Faculty of Science and Engineering; Nakayama, T. [Kobe Steel Ltd., Kobe (Japan)

    1996-11-01

    We developed a new laser surface acoustic wave (SAW) system and applied this to estimate the mechanical properties of the wear-resistant Ni-P layer electroplated on a stainless steel. The velocity dispersions of Rayleigh wave of the as -plated and heat-treated Ni-P layer were obtained by the one point time domain signal processing. The Ni-P layers with excellent wear resistance produced by the heated treatment higher than 725K were found to show higher Rayleigh velocities than that of the substrate steel, while the Ni-P layer with poor wear resistance showed lower velocities. Young`s moduli of the Ni-P layer, estimated so as the computed velocity dispersion agreed with the measured one, increased with the increase of wear resistance. 10 refs., 9 figs., 2 tabs.

  16. Characteristics of a Ti:sapphire laser pumped by a Nd:YAG laser and its analysis. Nd:YAG laser reiki Ti:sapphire laser no dosa tokusei to sono kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okada, T.; Masumoto, J.; Mizunami, T.; Maeda, M.; Muraoka, K. (Kyushu Univ., Fukuoka (Japan). Faculty of Engineering)

    1991-06-29

    Although Ti: Sapphire expects of a possibility of being a light source much superior to a dye laser having been used as a wavelength variable laser for spectral analyses, it has a limitation that it does not oscillate directly in the visible and ultraviolet regions. In order to develop a light source that is synchronizable over ultraviolet-near infrared regions, by means of combining a Ti: Sapphire laser of a high peak power, comprising an oscillator and a multistage amplifier, with a non-linear frequency conversion method for harmonic generation and Raman conversion, a prototype Ti:Sapphire laser that is excited by YAG laser second harmonic, and that synchronizes with a prism was fabricated, and its operational characteristics were investigated. As a result, an output energy of 35.6 mJ at a maximum was obtained at a wavelength of 773 nm against an excitation energy of 129 mJ, a conversion efficiency of 38.2% was obtained against the absorption energy of the crystals, and a continuous synchronism was achieved over 750 to 900 nm. 4 refs., 9 figs., 1 tab.

  17. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer.; Effects of acoustic excitation on combustion properties; Soshiki kozo wo tomonau sendan kakusan kaen no onkyo reiki.; Onkyo reiki ni yoru nensho tokusei no henka

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. [Nagoya Institute of Technology, Nagoya (Japan)

    1993-10-25

    This paper reports on experiments for acoustic excitation of plane shear structured flame. Flows of air separated into the higher velocity side and the lower velocity side by a partition on the center of a flow path merge at the measuring point to form a mixed layer with coherent structure. Fuel is supplied to this mixed layer with the flows so adjusted that the generated flame will attach to the partition on the lower velocity side. Acoustic excitation (at a sound pressure level of 100 dB to 120 dB) is performed in a speaker fitted on a wall on the higher velocity side. The paper mentions the results of the experiments as follows: the acoustic excitation produces such changes to diffusion flame in the plane shear layer as shorter flame and blue flame combustion and clarification of flame structures; as seen from spectral characteristics of temperature change in the flames, a flame acoustically excited strongly presents remarkable improvements in periodicity of the structure; as seen from sound pressure distribution in the flow direction at the measuring point, the flame zone of the flame acoustically excited strongly is positioned at the middle of the node and loop of a standing wave. 6 refs., 9 figs., 1 tab.

  18. Master curves for creep properties of CFRP, GFRP and CF/GF sandwich laminates. CFRP oyobi CF/GF sanso FRP no mage creep tokusei ni kansuru jikan-ondo kansansoku no tekiyosei

    Energy Technology Data Exchange (ETDEWEB)

    Furue, H. (Mechanical Engineering Laboratory, Tsukuba (Japan))

    1994-04-15

    An attempt has been made to apply a time/temperature conversion law in order to estimate creep characteristics of CFRP, GFRP and three-ply laminate using them. It was recognized from a creep distortion versus time curve that the creep distortion is dependent on time and temperature. The creep elasticity versus time curve showed that the creep elasticity decreases as the GFRP ratio increases, temperature rises, and creep time grows longer. The latter curve was used to derive a master curve for the creep elasticity. A comparison of this curve with the creep test result revealed that the estimation by using the time/temperature conversion law agreed with the result within the range of temperatures lower than Tg and [theta]=0-45[degree] (angles in fiber texture directions) in the case of CFRP. This relationship was not established in the three-ply laminate and GFRP because of material variance being too great. If the conversion becomes possible in wider range by selecting appropriate experiment temperature interval and measurement duration with respect to CFRP, the time/temperature conversion law could be more useful in estimating still longer time. 4 refs., 5 figs., 2 tabs.

  19. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium--Creation of key industries (Research and development of emission-free material separation and recycling process technologies for spent electric/electronic products); 1998 nendo shiyozomi denki denshi kogyo seihin no emissionless sozai bunri saisei junkan system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The personal computer is taken up as a sample, and studies are conducted about a system for separating and recovering recyclable materials. For the high-speed cutting and crushing of materials and their compaction, a water-jet cutting method is employed, which enables the unification of chip sizes after cutting, the prevention of dust generation, and the realization of clean working environments. For the separation of copper wires from their coats, a high-speed peeling machine is developed, and the copper wires are recovered for reuse. Fluorine plastics and polyester resin that constitute the coats do not show deterioration in their resin properties when put back into use. As for the powder resulting from the crushing of print circuit boards, it produces gas and unburnt carbon when subjected to heat treatment at 600 degrees C in inactive gas. The problem to arise from this recovery method is how to lower the cost. The separation of pelletized polymers and metal constituents can be accomplished by changing the ablation generation limit energy level during excimer laser irradiation, and this allows them to be recycled. (NEDO)

  20. Fiscal 1998 research report on the history and succession of industrial technologies. Research on the originality and creativity of electric and electronic technologies in the Japanese industry; 1998 nendo chosa hokokusho. Sangyo gijutsu rekishi keisho chosa (kokunai sangyo no denki denshi gijutsu no dokusosei to sozosei no chosahen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the interview survey results on development, introduction and succession of industrial technologies from pioneers with many concrete valuable experiences, aiming at technology succession and acquisition of suggestions. The interview survey was made on 'My course until now' and 'My electric power and slow concentrated accomplishment' from two pioneers, honorary professor Dr. Okamura Sogo of the University of Tokyo (department of electrical engineering), and honorary professor Dr. Miyaji Iwao of Nagoya University (department of electrical engineering). Dr. Okamura mentioned a precious encouraging word 'Learn the past for the future' for the young easy-to- lose sight of targets from the viewpoint that the 21st century is an age of education and welfare after the high economic growth age. Dr. Miyaji mentioned the basic attitude 'Continuity of selection day after day' and a precious word 'Maintain continuous friendship' for the young, leaving a deep impression to the interviewers. (NEDO)

  1. JPRS Report, Science & Technology, Japan: Symposium on Applications of Advanced Technology: Sensors

    Science.gov (United States)

    1992-03-02

    Yamada), Kagaku Dojin 1. Suzuki, K., et al., FRAGRANCE JOURNAL, No 87, Publishers, 1983. 1987 p 60. 11. Yamano, Y., PETROLEUM CHEMISTRY, Vol 35, 2...issues or single copies of the DAILY Documents, U.S. Government Printing Office, Wash- REPORTs and JPRS publications are not available. ington, D.C

  2. JPRS Report, Science & Technology, Japan

    Science.gov (United States)

    1988-03-03

    in space and recovery of the rock - et’s nose portion from the ocean. The overall shape of the rocket is shown in Figure 6. It is a two-stage rocket...Industrial Machinery Nippon Sharyo Seizo Kobe Steel, Ltd. Riken Kagaku Tosh in Toyo Seiki Seisa- kusho Nakatani Machines Function Furnaces

  3. Industrial science and technology research and development business for fiscal 1998. Research and development achievement report on glycoconjugate production and utilization technologies (Development of technologies of glycoconjugate-aided CO{sub 2} fixation and utilization); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu seika hokokusho (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Enzymatic and chemical methods were combined and methods were developed for synthesizing mucin type sugar chains and glycopeptides. The influence of sugar chain positions and structures on glycoconjugate stereo structures and physiological activities was analyzed, and glycopeptide structural activities and glycoconjugate remodelling were studied. To create an industrial advantage in a glycoprotein production system by use of zooblasts, sugar chain structure control through sugar transfase occurrence control was studied. For the production of man-adaptive sugar chains using yeast, new yeast variations were subjected to molecular breeding, and tested for the resultant improvement on productivity. Sugar chain marking and refining techniques and various responding mechanisms on the solid surface were elucidated, which enabled structure analyses using sugar chain recognition molecules such as lectins and antibodies. A database on interactions between sugar chains and sugar chain recognition molecules was constructed using the said findings. An analyzing program was also formulated tentatively. This paper also covers general surveys and studies on technologies of producing and utilizing glycoconjugates. (NEDO)

  4. Fiscal 1997 report on the results of the international standardization R and D. Measurement of ultra-micro chemical substances and measuring methods of hormone effects; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Chobiryo kagaku busshitsu no keisoku horumon eikyo sayo sokuteiho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the measurement system of ultra-micro hazardous chemical substances in the global environment, the paper examined the present situation of chemical substances such as dioxins, made an experimental study on the method to analyze dioxins in exhaust gas from an aspect of international consistency, and worked out a JIS draft. As to the standard measuring method of hormone effects of chemical substances, the paper developed the competitive bonding experiment system to measure bonding ability of chemical substances to homo sapiens estrogen receptor (ER). By measuring ER bonding ability of 78 kinds of chemical substances, the measuring method was developed. In the development of the assay system for detection of hormone-like compounds, the assay system with transfer activity via estrogen receptor as an index was established using cultured cells and yeast. Further, the development was made of a measuring method of receptor bonding activity of hormone-like substances. 33 refs., 151 figs., 66 tabs.

  5. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Research and development of ultrahigh temperature gas turbine for power generation); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden'yo chokoon gas turbine no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fruits of fiscal 2000 efforts to develop high temperature energy materials and ultraprecision materials are briefly described. Activities are conducted in the four fields of (1) materials derivation and advanced evaluation/design technologies, (2) application technologies, (3) common base technologies, and (4) multifunction realization process evaluation. Discussed in field (1) are high temperature energy materials, high performance active materials, fundamental technologies for member designing, active materials for dealing with environmental gas, silicon based high resistance energy materials, porous multiple layer ceramic materials, macro-/micro-scale stress analysis technology, and microfracture analysis technology. Discussed in field (2) are heat resistant and damage tolerant materials, heat shielding materials and energy absorbing materials, and nanofilter materials capable of selective separation. In the study of active materials specific for environmental gas, a catalyst is developed, stable at high temperatures and capable of treating NOx selectively. The catalyst is a layered product comprising Ba hexaaluminate layers and stabilized zirconia layers. (NEDO)

  6. Model project for enhancing energy consumption efficiency in developing countries. Report on changes of energy conservation technology and environmental protection technology in the chemical industry of Japan; Hatten tojokoku energy shohi koritsuka model jigyo. Nippon kagaku kogyo ni okeru sho energy gijutsu to kankyo taisaku gijutsu no hensen hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the economic growth and the global environmental protection in the Asian area, an investigation was carried out into energy conservation technology and environmental protection technology in the chemical industry of Japan. Measures for energy conservation are shifting from those which do not cost so much such as reduction in excess air rate of the heating furnace, and reduction in reflux ratio of the distillation tower to those with equipment investment such as waste heat recovery of the heating furnace and waste heat recovery of the distillation tower. In the 1980s, the utilization of low temperature waste heat by absorption type refrigerator and heat pump was promoted and the energy utilization efficiency by computer control was enhanced. Concerning environmental measures, the following were carried out: installation of the flue gas desulfurization device and reconstruction of high-rise stack, reduction of NOx by combustion control, smoke/dust disposal of electrostatic precipitator, combustion of hydrocarbon causing photochemical oxidant, catalytic oxidation, condensation, treatment by activated carbon, activated sludge treatment for BOD/COD, diaphragm process for dimethylmercury, ion exchange resin process, etc. 21 refs., 29 figs., 27 tabs.

  7. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. Cluster ion beam process technology; 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seido seika hokokusho. Cluster ion beam process technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of development of cluster ion beams. This technology generates the strong ion beams of atom and molecule clusters, and irradiate them onto the solid surfaces, to create new materials or treat materials. It allows the nano-level treatment. The program for high-current cluster ion beam generation/irradiation technology for industrial purposes attains the target high-current beam of 500{mu}m. It is necessary to establish the optimum cluster size, irradiated energy and ion species for the highly functional surface treatment, for which applicable technologies, e.g., those related to time of flight and molecular dynamics, are developed. Studies on high-current, large-area irradiation technologies are started. The program for material processing technologies involves evaluation of crystalline defects formed during the beam implantation by photoluminescence spectroscopy, and studies on semiconductor surface processing technologies. The surface smoothening technology is investigated to reduce crystalline defects and stress-induced strains for difficult-to-process materials, e.g., SiC and diamond, and the good results are produced. The program for development of superflat/superhard thin film formation technology involves irradiation of the Ar ion beams during the deposition of C{sub 60}(fullerene), to produce the superhard thin film. (NEDO)

  8. Report on survey for fiscal 1997. Survey concerning the effective use of the products of Industrial and Scientific Technologies Research and Development System; 1997 nendo chosa hokokusho. Sangyo kagaku gijutsu kenkyu kaihatsu seido no seika no katsuyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey aims at formulating measures for further soliciting the effective use of the products yielded up to date by the above-named system and at suggesting them to NEDO (New Energy and Industrial Technology Development Organization) who operate the system. In the survey, questionnaires are given and replied, about how the results of the industrial technology system and the public request for proposition system have been utilized, respectively. As for the enforcement of in-house research and development efforts after the project, 54% answer affirmative, 46% negative. The enforcement rate is relatively high in `recombinant DNA utilization technology,` `photoreactive materials,` `bio-element,` and `super-advanced processing system.` The enforcement rate is low in `fine ceramics` and `technology for creating space at great depth.` As for the feasibility of the products of the system, 76% are judged feasible and 23% unfeasible. Ranked high in feasibility are `processing technology creating advanced functions,` `fine ceramics,` `ultimate work robot,` and `super-advanced processing system.` Feasibility is judged low in `recombinant DNA utilization technology,` `photoreactive materials,` and `bio-element.` 2 refs., 16 figs., 6 tabs.

  9. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

  10. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  11. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  12. Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and increase in density of matrixes, and harmonization with long fibers. Silicon nitride was trially made with low lubrication/friction coefficients and high strength. A simulation method for crack progress behavior evaluation was developed using a testing notched specimen heterogeneous microstructures. Analyses were made of brittle fracture mechanics and reliability evaluation. 273 refs., 344 figs., 29 tabs.

  13. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  14. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  15. Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

  16. Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

  17. Industrial science and technology research and development project of university cooperative type in fiscal 2000. Report on achievements in semiconductor device manufacturing processes using Cat-CVD method (Development of technology to rationalize energy usage); 2000 nendo daigaku renkeigata sangyo kagaku gijutsu kenkyu kaihatsu project. Cat-CVD ho ni yoru handotai device seizo process seika hokokusho (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The catalytic chemical vapor deposition (Cat-CVD) method is a low-temperature thin film depositing technology that can achieve improvement in quality of semiconductor thin films and can perform inexpensive film deposition in a large area. This paper summarizes the achievements in fiscal 2000 in the demonstrative research and development theme of the present project, centering on the following five areas: 1) discussions on application of the Cat-CVD method to the mass production process for gallium arsenide integrated circuits, 2) studies on the possibility to apply the Cat-CVD method to the process to fabricate nitrided silicon protective film for ferroelectric memory devices, 3) formation of nitrided silicon films for silicon integrated circuits by means of the Cat-CVD method, and development of a chamber cleaning technology, 4) fabrication of high-mobility poly-crystalline silicon thin film transistors formed by using the Cat-CVD method and large particle size poly-crystalline silicon films by using the catalytic chemical sputtering process, and 5) discussions on properties of amorphous silicon thin film transistors formed by using the Cat-CVD method and formation of large area films by using a catalyst integrated shower head. (NEDO)

  18. Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

  19. Fiscal 1998 R and D project on global environmental industrial technology. R and D result report on environment- friendly production technology (advanced chemical synthesis reactor); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bio reactor) kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For high-efficiency production of substances by bioreactor, study was made on a bio-control mechanism as its elementary technology. On the study of breeding technology by expression control, the structure design of a control region and development of new expression vectors had been finished, and study was made on breeding of high-efficiency recombinant production cells by using candidate expression vectors. On the study of breeding technology by multi-stage enzyme reaction control, the enzyme gene of a system synthesizing cysteine from glycerol was searched, and hydroxypyruvaldehyde hydrogenase gene was isolated as substance production model. Cysteine production Escherichia coli combined with serineacetyl transferase gene was also prepared. In addition, study started on cloning of hydroxyacetone oxidase gene. On development of reactor system technology, for conversion of serine to cysteine, study was made on optimization of a reaction condition by theory of enzyme reaction rate. (NEDO)

  20. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  1. Determination of the crystallite orientation distribution from direct pole figures

    International Nuclear Information System (INIS)

    Araujo Gomes, P.A.M. de.

    1977-01-01

    A method is described which allows to calculate the crystallite orientation distribution in polycrystalline material, from direct pole figures data of its crystallographic planes (Roe's Method). The programme was applied to (1010), (0002), (1011) and (1120) complete pole figures data for a commercial, thin sheet Zircaloy-4 tubing specimen. A semi-automatic Rigaku-Denki texture goniometer, which scans the reciprocal lattice sphere pointwise outputting the data in a punched tape, was used to obtain the pole figures. This is consistent with the results obtained through direct conclusion from the pole figures. (author)

  2. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use unused hydrocarbon resource, technology of solid electrolyte fuel cells for high-efficient electric vehicles); 1993 nendo kokusai kenkyu kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kokoritsu denki jidosha no kotai denkaishitsu nenryo denchi gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) solid electrolyte fuel cell (SOFC) technology for high-efficient electric vehicles. In 1), bio-remediation is a choice as the result of trially using technologies for remediation of the environment polluted by pollutant, but it is not a technically completed one, but one which will be improved by trial and error. By the application of gene engineering, the use of gene recombination enables wide spread of decomposition genes. In 2), technical subjects were studied such as superheavy distillate, oil shale, coalhead methane and methane hydrate. In 3), designed were cylinder type and planar type SOFC of 850degC operation and 10kW output. Accumulation and weight of a total SOFC system are 81 liters and 100 kg in cylinder type and 136 liters and 200 kg in planar type. The vehicle can be equipped with the SOFC. 171 refs., 72 figs., 54 tabs.

  3. JPRS Report, Science & Technology, Japan, 28th Ceramics Science Discussion

    Science.gov (United States)

    1990-11-13

    Hiroshi Asakura , Hiroshi Yamamura] .............................. 59 Microstructure, Dielectric Properties of Tungsten Bronze-Type Ceramics [Yoji Ueda...67 Synthesis of Ag-Added Bi-Pb-Ca-Cu-O Powder by Spray Drying, Superconductivity of Powder [ Hiroko Higuma, Mitsunobu Wakata, et al...SERAMIKKUSU KISO KAGAKU TORONKAI in Japanese 24 Jan 90 p 160 [Article by Hiroshi Asakura and Hiroshi Yamamura, TOSO Corp.] [Text] 1. Introduction In cases

  4. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Basic study of measurement of human characteristics); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (Ningen tokusei keisoku ni kansuru kiban kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the development of working conditions fit for aged people and devices for them to operate, their visual function and behavioral characteristics are measured and analyzed. In the study of visual functions, 50 people from local cities and regions and another 50 from Osaka and its neighboring cities are subjected to measurement regarding visual acuity required in daily life, color discrimination, dark adaptation, glare, and the like. In the study of performing characteristics, 500 people are subjected to measurement regarding the scope of movement of upper limbs, their reach, and skillfulness with which the people can move fingers. When brightness, luminance, and contrast are caused to change relative to letters and background, aging is found to exert a great influence on the ease of reading, dark adaptation, and glare. As for the upper limb work range and reachability and the skillfulness in finger movement, it is found that aging narrows down the tolerant work area, lowers the working pace, and greatly affects skillfulness depending on the device operating method, all these disclosing actualities of difference attributable to age and sex. Concerning the device operating position and the ease of device operating force application, new measuring and evaluating methods are worked out, and correlations between the contents of operation and the operating position are seized. (NEDO)

  5. Response characteristics of a long life type floating offshore airport in waves. 3rd Report. Response due to short waves and an attempt of active inclination control; Chojumyogata futaishiki kaijo kuko no harochu oto tokusei. Tanhachoiki no oto oyobi shisei seigyo no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, T.; Ma, N.; Nishio, O.; Sato, N. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1996-12-31

    Notice was given on response characteristics in a short wavelength range of a large floating structure for an offshore airport consisting of semi-submersible replaceable type units, and influence of unit lacking. An attempt was also made on performing restoration of inclination change during unit lacking and suppression of long-cycle variation in waves by using air pressure control. The result of a numerical calculation based on a three-dimensional singular point method may be summarized as follows: mass force added vertically on columns in short wavelength range differs in the outer edges and the central part; relatively uniform values are shown in the central part; and interactive interference is recognized in wave forces in the vertical direction, but the influence therefrom decreases as the wave length decreases. Calculations on vertical movements and bending moments in waves were performed by using a mode synthesizing method. The calculations used fluid force which was calculated based on the three-dimensional singular point method utilizing symmetry with respect to each condition for a complete model plus unit lacking and unit lacking plus inclination control. As a result of verifying the calculations by using an experiment, relatively good agreement was achieved in either case. A high-frequency vibration experiment made clear the characteristics of elastic response in the short-wave length range. 14 refs., 14 figs.

  6. Method for estimation of the output electric power of PV module with considering environmental factors. Method for estimation of output using I-V curves; Kankyo inshi wo koryoshita taiyo denchi module no shutsuryoku keisanho. I-V tokusei curve ni yoru keisan

    Energy Technology Data Exchange (ETDEWEB)

    Yamagami, Y.; Tani, T. [Science University of Tokyo, Tokyo (Japan)

    1996-10-27

    Based on the basic quality equation of photovoltaic (PV) cell, a quality equation of PV module has been constructed by considering the spectral distribution of solar radiation and its intensity. A calculation method has been also proposed for determining the output from current-voltage (I-V) curves. Effectiveness of this method was examined by comparing calculated results and observed results. Amorphous Si (a-Si) and polycrystal Si PV modules were examined. By considering the environmental factors, differences of the annual output between the calculated and observed values were reduced from 2.50% to 0.95% for the a-Si PV module, and from 2.52% to 1.24% for the polycrystal Si PV module, which resulted in the reduction more than 50%. For the a-Si PV module, the environmental factor most greatly affecting the annual output was the spectral distribution of solar radiation, which was 3.86 times as large as the cell temperature, and 1.04 times as large as the intensity of solar radiation. For the polycrystal PV module, the environmental factor most greatly affecting the annual output was the cell temperature, which was 7.05 times as large as the spectral distribution of solar radiation, and 1.74 times as large as the intensity of solar radiation. 6 refs., 4 figs., 1 tab.

  7. Creeping discharge characteristics in N{sub 2}/SF{sub 6} and N{sub 2}/O{sub 2} gas mixture; N{sub 2}/SF{sub 6}, N{sub 2}/O{sub 2} kongo gas chu ni okeru enmen hoden tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, H.; Watabe, K.; Nakayama, H. [Himeji Institute of Technology, Hyogo (Japan). Faculty of Engineering

    1999-11-05

    Creeping flashover characteristics of a composite insulating system with a solid insulator between a needle electrode and a plane electrode have been investigated. A negative creeping flashover voltage drastically decreased by the 0.5% admixture of electronegative gas (SF{sub 6}, O{sub 2}) into N{sub 2}, gas, and a highly emissive region at the top of a creeping corona was found in their gas mixtures. However, a photon emission in the creeping corona extension process in N{sub 2}/SF{sub 6} and N{sub 2}/O{sub 2} was very similar to that in pure N{sub 2}. These results suggest that a formation of negative ion by the electron attachment would not be so effective in N{sub 2}/SF{sub 6} and N{sub 2}/O{sub 2} at a low electronegative gas content. (author)

  8. Properties of P/M forged Al-Si alloys made by premixed powders. 1. Influences of dispersion and sizes of proeutectic Si on wear resistance; Kongoho ni yotte sakuseishita Al-Si kei shoketsu tanzo gokin no tokusei. 1. Taimamosei ni oyobosu shosho Si no bunsan jotai to ryukei no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishijima, Z.; Ichikawa, J.; Sasaki, s.; Shikata, H. [Hitachi Powdered Metals Co. Ltd., Tokyo (Japan)

    1995-10-15

    Influences of dispersion and sizes of proeutectic Si on wear resistance of P/M Al-Si alloys using the prealloying method and premixing method have been investigated. As a result, discretely dispersed proeutectic Si showed excellent wear resistance in compassion with uniformly dispersed one. The cause is considered to be the unclosed Si soft phase which has been preferentially worn away, consequently acting on forming oil grooves and burying worn particles. Further more the existence of the optimum size of proeutectic Si on wear resistance was confirmed. In the case of finer particles, only Al-Si alloy (pin) was warned away substantially. On the other handgun the case of larger particles, both the Al-Si alloy (pin) and the mating malarial (steel disc) were excessively warned away. It is assumed therefore that the finer proeutectic Si particles are not effective as hard particles, on the contrary, larger proeutectic Si particles increase the abrasive wear against the mating material, and those buried into the mating material initiate wear of Al-Si alloy at the same time. 2 refs., 10 figs., 1 tab.

  9. Development of a 4K/80K multiple operating type of GM refrigeration system for the superconducting magnet in maglev use. Cooling characteristics of the nitrogen self-circulated cooling-type radiation shield plate; Fujoshiki tetsudoyo chodendojishaku no 4K/80K ryoyo GM reito sisutemu no kaihatsu. Chisso shizen junkanhoshiki netsu shirudo no reikyaku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakao, Hiroyuki; Takahashi, Masahiko; Sanada, Yoshinao; Yamashita, Tomohiro; Yamaji, Mutsuhiko [Toshiba Corp., Tokyo (Japan); Terai, Motoaki [Central Japan Railway Corp., Tokyo (Japan); Igarashi, Motohiro; Yamaguchi, Mitsugu [Niigata Unviersity, Niigata (Japan)

    1999-02-25

    An onboard refrigeration system is one of the most important components in the superconducting magnetically levitated system (Maglev system). In the superconducting magnet, liquid helium and nitrogen are used to cool the superconducting coils and the radiation shields. At the Yamanashi Maglev Test Line, the operation of the superconducting magnet without a supplement of liquid helium has been achieved by the onboard 4 K Gifford-McMahon/Joule-Thomson (GM/JT) refrigerators- . As for the liquid nitrogen, it is supplied to the radiation shields periodically. Our final target for an onboard refrigeration system for commercial use is to operate magnets with no supplementation of cryogen. That is the operations of magnets should not depend on a helium liquefaction plant or a liquid nitrogen supplying system in the train depot, except for occasions of the magnet's precooling or when the vehicle is being overhauled. To meet these requirements, we have been developing a new type of onboard GM refrigeration (GM refrigerator application) system that features a combination of a 4K/80K multiple-operating type of GM refrigerator and a self-circulated cooling-type radiation shield. The nitrogen self-circulated cooling-type radiation shield plate was demonstrated by using the radiation shield plate mock-up. (author)

  10. Unstable brittle crack-arrest toughness of newly developed steel plate with surface layers having ultra fine grain microstructure. Part 2. Crack-arrest toughness of the plate after plastic damage and its application to prevent crack expansion after a collision; Hyoso chosairyuko no zeisei kiretsu denpa teishi seino. 2. Sosei sonsho go no tokusei oyobi shototsugo no kiretsu kakudai boshi eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, T.; Hagiwara, Y.; Inoue, T.; Oshita, S. [Nippon Steel Corp., Tokyo (Japan); Kuroiwa, T.; Hashimoto, T. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Tada, M. [Mitsubishi Heavy Industries Ltd., Nagasaki (Japan). Nagasaki Technical Inst.; Yajima, H. [Hiroshima Univ. (Japan). Faculty of Engineering

    1995-12-01

    Use of ships with high safety and reliability that can suppress the casualties and ocean pollution accidents caused by ships failure to a minimum, are in demand. Therefore, in order to study the improvement of safety when steel plates with surface layers having ultra fine grain microstructure and having extremely improved arrest characteristic are used for ship structures, fracture simulation of collision and comparative evaluation of the arrest properties with the conventional steel plate were carried out. Firstly, fracture simulation of the ship bodycaused by the collision of very large crude oil carries (VLCC) was carried out and the plastic strain caused during the collision was quantified. After that, as for steel plate with surface layers having ultrafine grain microstructure and normal KE 36 steel plate, comparative study of arrestability of steel plate under 10% plastic strain was made. As a result, it was revealed that sufficient arrest efficiency was secured by using steel plate with surface layers having ultra fine grain structure even for the case where arrestability for long big crack is not secured in case of normal KE 36 steel plate due to the plastic strain effect on VLCC caused by collision. 11 refs., 18 figs., 5 tabs.

  11. Influence of bow-tie trees on the residual AC breakdown voltage of dry-cured XLPE power cables under immersed accelerated aging test. Shinsui kadenka ni okeru kanshiki kakyo polyethylene cable no zanson hakai den'atsu tokusei ni oyobosu bow tie jo mizu tree no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Hashizume, T.; Shinoda, C.; Nakamura, K.; Hotta, M.; Tani, T. (Yazaki Electric Wire Co. Ltd., Tokyo (Japan))

    1994-03-20

    A 6-kV class polyethylene cable manufactured by using a dry-cured three-layer extrusion system has been subjected to accelerated deterioration under immersed condition (at a voltage of 6.9V and a frequency of 1 kHz for an application period as long as 18 months as maximum). The cable had then been given a breakdown test by means of an application method based on the electric power standard to derive the residual breakdown voltage characteristics. Causes of the breakdown have been discussed by using a pre-interruption method. This paper reports the result of the discussion. The following findings have been obtained: the residual breakdown voltage values vary largely on the whole, but no trend has been observed that the voltage decreases as the application period for accelerated deterioration becomes longer; generation of bow-tie trees (with a length of about 600 [mu]m or longer) in contact with internal or external semiconduction layer largely reduces the breakdown voltage values, and presence of bow-tie trees has increased the variation in the breakdown values; and the breakdown voltage values vary largely due to moisture in the bow-tie trees contacting the semiconduction layer. 12 refs., 13 figs., 3 tabs.

  12. Alternating current carrying features of copper spot-contacts with powder contamination produced by arc discharges in SF sub 6 gas. SF sub 6 bunkai seiseibutsu ga kaizaishita do ten sesshokushi no koryu denryu tsuden tokusei ni kansuru jikken teki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Aichi, H.; Satone, H. (Daido Inst. of Tech., Nagoya (Japan)); Matsumura, T. (Kyoto Univ., Kyoto (Japan)); Kito, Y. (Nagoya Univ., Nagoya (Japan)); Mukaiyama, Y.; Takagi, I. (Chubu Electric Power Co. Inc., Nagoya (Japan))

    1991-05-20

    The voltage and its waveform were experimentally investigated when alternating current was carried by copper spot-contacts contaminated by the powder products produced between them by the arc discharge or the like in SF {sub 6}. The voltage between the contacts and the abnormal phenomena of its waveform were studied when the decomposed product powder of SF {sub 6} adhered the contact area. It was observed that the waveform of the voltage is square in the early stage of current carrying which becomes triangular with the increases in current carrying and passage of time, and then changes further into sinusoidal form. As a result, it was confirmed that the square and triangular voltage waveforms were produced because the spot-contacts are contaminated with powder substances. 4 refs., 9 figs., 1 tab.

  13. Characteristics of combustion and heat transfer of excess enthalpy flames stabilized in a stagnation flow. 2nd Report. ; Heat flux at high flow rate and effects of Lewis number. Yodomi nagarechu ni anteika sareta choka enthalpy kaen no nensho oyobi etsudentatsu tokusei. 2. ; Koryuryo ni okeru netsuryusoku oyobi Lewis su no koka

    Energy Technology Data Exchange (ETDEWEB)

    Ito, S. (Daido Institute of Technology, Nagoya (Japan)); Asato, K.; Kawamura, T. (Gifu University, Gifu (Japan). Faculty of Engineerirng); Mazaki, T. (Daido Senior High School, Nagoya (Japan)); Umemura, H. (Mitsubishi Electric Corp., Tokyo (Japan))

    1993-08-25

    For the purpose of developing small-sized combustors of high heat transfer efficiency for household and business uses, a study has been carried out on the characteristics of an excess enthalpy flame stabilized in a stagnant flow, the maximum heat flux utilizable from flames through a heat receiver wall, the heat transfer characteristics near the extinction limits, and the effects of Lewis number (Le). Even when heat is drawn from the heat receiver wall in the downstream of flames, stable flames are kept until they extremely approach the heat receiver wall by the effect of preheating for lean methane-air flames of Le[approx equal]1.0 and lean propane-air flames of Le>1.0 and by the effect of preheating and Lewis effect for lean hydrogen-air flames of Le<1.0. In any flames, therefore, the heat flux to the heat receiver wall increases abruptly with the increase of stagnant velocity gradient and thereby the heat transfer characteristics at the heat receiver wall are improved. Heat transfer in the cases where flames exist on the outside and inside of the temperature boundary layer depend not on the thickness of the temperature boundary layer but on the position of flames. 6 refs., 9 figs.

  14. Change of photovoltaic module conversion efficiency with the environmental factors in different site. Comparison of the conversion efficiency in Tokyo with the one in Nagano; Kotonaru chiten ni okeru taiyo denchi module no shutsuryoku tokusei no henka. Tokyoto Shinjukuku to Naganoken Chinoshi tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, T.; Tani, T.; Hirata, Y.; Inasaka, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Assuming that photovoltaic power systems were installed at two points, Shinjuku Tokyo and Chino Nagano, a study was conducted of difference in generated output of the systems caused by the difference in environmental factors. In the study, it was assumed that two of the photovoltaic power system with rated capacity of 3kW were installed at the two points, and the annual generated output was calculated and compared by the conventional method considering only cell temperature and the output estimation method considering intensity of solar radiation, cell temperature, and spectral distribution of solar radiation. The result of the study was as follows: the difference in output ratio at the two points was 1.7% or lower under the influence of intensity of solar radiation and cell temperature. On the other hand, under the influence of the distribution of spectral solar radiation, the difference is larger than under other environmental factors, 2.4% in polycrystalline Si and 5.5% in amorphous Si. The generated output estimated by the conventional method and the spectral method produced a difference between 81 kWh in Tokyo and 258 kWh in Nagano in amorphous Si. This is because environmental factors such as intensity of solar radiation and distribution of spectral solar radiation are different between the two points. 1 ref., 2 figs., 3 tabs.

  15. Experimentation to seek the local speciality in kWh of P.V. system, and a study of its measuring method and instruments and apparatus; Taiyoko hatsuden system no jibetsu hatsudenryo no chiiki tokusei wo motomeru jissho shiken narabini, sono sokutei kansoku no hoho kiki ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Anno, T.

    1997-11-25

    Introduced in this paper are some problems that the author encounters in relation with a 2.6kW photovoltaic power generation system installed at the author`s residence for the purpose of measuring the hourly amounts of generated power. Giving rise to questions in the inverter and the control system are the conversion efficiency under a partial load, the scope of little amounts that are omitted, the maximum power point tracking system and its performance, etc. The author wants to learn how to land on an appropriate conductor thickness and to know the special specifications if any for heavy-snow regions and their effect. Much has been learned from presenters, moderators, and participants at scientific events and through private talks. Although it seems that there exists some relationship between the maximum power point tracking system and the diameter of conductors suitable for the system, yet the manufacturers fail to give clear-cut answers. The author thinks that end-users find many black box-like parts in the system, which the author leaves uncared for now for later study. It is learned that there is no specification intended exclusively for heavy-snow regions. The author`s system is in operation with hourly output recording and data accumulation started. 2 figs.

  16. 1998 Annual Study Report. Standardization of methods for evaluating characteristics of high-strength, large-diameter steel pipes for superhigh-pressure natural gas pipelines; 1998 nendo seika hokokusho. Chokoatsu tennen gas pipeline yo kokyodo daikei kokan no tokusei hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The pipelines for safely transmitting superhigh-pressure natural gas should have excellent characteristics. The steel pipe is required to have a sufficient toughness, more concretely Charpy impact-absorbing energy, to prevent propagating shear fracture characteristic of natural gas pipelines. Recently, the natural gas pipeline is increasingly required to have higher design pressures (15 Mpa or higher) and grade (X80 or higher). In order to develop the techniques for simulating crack propagation in the propagating shear fracture of natural gas pipe lines as part of the programs to cope with these trends, the 1998 efforts were directed to reviewing the research results obtained so far and analysis of the problems to be solved and tasks to be taken, based on which the analytical procedure for gas releasing phenomena during the fracture process was basically developed, the material characteristic data were collected by the laboratory scale toughness tests, and the preliminary tests with rupture disks were conducted to verify the above analytical procedure. These efforts have established the bases for evaluating the characteristics of high-strength, large-diameter steel pipes in the light of safety against fracture, and greatly advanced the program towards the final target of developing the international specification drafts for toughness. (NEDO)

  17. Discharge-current characteristics in UV-preionized Kr/He, F2/He gas-mixtures and KrF excimer laser gas. Shigaisen yobi denri Kr/He, F2/He kongo kitai hoden oyobi KrF laser reiki hoden no denryu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, N.; Kawakami, H.; Yukimura, K. (Doshisha University, Kyoto (Japan))

    1992-08-15

    In order to study effects of Kr and F2 on discharge characteristics of KrF excimer laser gas, gap phenomena in Kr/He and F2/He gas-mixtures were observed and discharge current (I[sub d]) was measured. In the range where Kr concentration was over 10% in Kr/He gas, in which production of filamentation as well as glow discharge started, discontinuous change in I[sub d] in the second or third half cycle was observed. According to the results of experiments and model analyses, it was considered that the discontinuity of the current showed the transition point to filamentation. When F2 concentration was in the range between 0.1 and 0.3% in F2/He mixture gas, filamentation and arc with glow were observed. Sine-waveform I[sub d] ended in the first half cycle, and began to flow again after cessation or had almost constant current due to arc and others. When F2 was over 0.4%, only are discharge was observed. It was thus found that F2 has a large effect on discharge characteristics of KrF laser gas. 18 refs., 9 figs.

  18. Combustion characteristics of stratified mixture. 1st Report. Measurement of mixture distribution in a constant-volume combustion chamber using laser-induced NO2 fluorescence; Sojo kongoki no nensho tokusei ni kansuru kenkyu. 1. Laser reiki NO2 keikoho ni yoru teiyo nenshokinai kongoki bunpu no keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, M.; Nishida, K.; Hiroyasu, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Tabata, M. [Mazda Motor Corp., Hiroshima (Japan)

    1996-06-25

    Laser-induced fluorescence from nitrogen dioxide (NO2) as gas fuel tracer was applied to determine mixture stratification in a pancake-type constant-volume combustion chamber using propane and hydrogen fuels. The second-harmonic output of a pulsed Nd: YAG laser was used as a light source for fluorescence excitation. The fluorescence images were corrected by a gated image-intensified CCD camera. The quantitative analysis of fuel concentration was made possible by the application of linearity between fluorescence intensity and NO2 concentration at a low trace level. The stratified mixture (center-rich or center-lean) was concentrically formed in the central region of the chamber by a jet flow from a tangentially oriented port. The concentration difference in the radial direction of the chamber decreased with time from the start of injection. The rate of decrease was faster for hydrogen than for propane. After 300 ms from start of injection, however, the time histories of the concentration difference were nearly constant for both fuels regardless of overall concentration. 10 refs., 16 figs., 1 tab.

  19. Boltzmann equation analysis of electrons swarm parameters and properties of excited particle number densities in Xe/Ne plasmas. Laser absorption effect; Xe/Ne plasma chudenshi yuso keisu narabi ni reiki ryushisu mitsudo tokusei no Boltzmann hoteishiki kaiseki. Laser ko kyushu koka

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, S.; Sugawara, H.; Ventzek, P.; Sakai, Y. [Hokkaido University, Sapporo (Japan)

    1998-06-01

    Xe/Ne plasmas are important for plasma display panels and VUV light sources. However, reactions between electrons and excited particles in the mixtures are so complicated that influence of the reactions on the plasma properties is not understood well. In this work, taking account of reactions through which electrons are produced, such as cumulative and Penning ionization, and of transition between excited levels, the electron and excited particle properties in Xe/Ne plasmas are calculated using the Boltzmann equation. The ionization coefficient and electron drift velocity agreed with experimental data. The influence of laser absorption in Xe/Ne plasmas on the plasma properties is also discussed. 25 refs., 15 figs.

  20. Preparation of spherical fine particulate pigments within water-in-oil emulsions and their properties. (II). ; Formation mechanism and characteristic of spherical fine particulate pigment of tartrazine. W/O emulsion wo mochiita kyujo biryushi ganryo no chosei to seishitsu(dai 2 ho). ; Kiiro 4 go kyujo biryushi ganryo no seisei kiko to tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Imai, T.; Iwano, K.; Hotta, H.; Takano, S.; Tsutsumi, H. (Kao Corporation, Tokyo (Japan))

    1991-12-20

    The previous report explained that an excellent spherical particulate pigment with a grain size of 0.5 mm or less can be obtained by preparing multinuclear aluminum lakes from acidic dyes and multinuclear aluminum salt using water droplets in a W/O emulsion as reaction fields. This paper describes preparing pigments varying the charging concentrations of the pigments in a W/O emulsion and the droplet particle size to discuss the mechanism of forming the pigments. As a result, it was found that the particle sizes in the produced pigments have a clear correlation with the charging concentrations of the pigments and the droplet particle sizes in the W/O emulsion. A pigment produced in the W/O emulsion forms only in its own droplets, and reflects its particle sizes. Films dispersed with pigments having different particle sizes were prepared to discuss their tinting abilities, whereas it was clarified that the smaller the particle size, the higher the tinting ability and the higher saturation in colored paint films. 6 refs., 9 figs., 3 tabs.

  1. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  2. FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 1/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (1/2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. The plant at installation site has been run since 1995, having a production capacity of 50,000-60,000 tons. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. (NEDO)

  3. FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 2/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (2/2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. The separate volume (2/2) included drawings of valve, fire detector, orifice, thermocouple, motor control equipment, etc. (NEDO)

  4. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  5. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  6. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

  7. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  8. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

  9. Industrial science and technology research and development project of university cooperative type in fiscal 2000. Report on achievements in semiconductor device manufacturing processes using Cat-CVD method (Semiconductor device manufacturing processes using Cat-CVD method); 2000 nendo daigaku renkeigata sangyo kagaku gijutsu kenkyu kaihatsu project. Cat-CVD ho ni yoru handotai device seizo process seika hokokusho (Cat-CVD ho ni yoru handotai device seizo process)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The catalytic chemical vapor deposition (Cat-CVD) method is a low-temperature thin film depositing technology that can achieve improvement in quality of semiconductor thin films and can perform inexpensive film deposition in a large area. The present project is composed of the basic research and development theme and the demonstrative research and development theme for the Cat-CVD method. This report summarizes the achievements in fiscal 2000 centering on the former theme. Discussions were given on the following five areas: 1) simulation on film thickness distribution in the Cat-CVD method, 2) life extension by preventing the catalyst converting into silicide and development of a catalyst integrated shear head, 3) vapor diagnosis in the film forming process by the Cat-CVD method using silane, hydrogen and ammonia, 4) a technology for high-speed deposition of hydrogenated amorphous silicon films for solar cells using the Cat-CVD method, and the low-temperature silicon oxide nitriding technology using heated catalysts, and 5) discussions on compatibility of transparent oxide electrode materials to the process of manufacturing thin-film silicon-based solar cells by using the Cat-CVD method. (NEDO)

  10. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  11. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

  12. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  13. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

  14. Biotechnology of Tohoku Electric Power Co. Application of plant biotechnology/Biomass utilization/Development of technology to control cold resistance of plant/Practical application of passion fruit growing technology/Identification of useful genes of plant/Light supplement growing of rose/Electric stimulus growing of shiitake mushroom,etc; Tohoku Denryoku no biotechnology. Shokubutsu biotechnology oyo, biomass riyo, shokubutsu no taireisei seigyo gijutsu kaihatsu, passion fruit saibai gijutsu no jitsuyoka, shokubutsu no yuyo idenshi dotei, bara no hoko saibai, shiitake denki shigeki saibai gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-10-01

    The paper introduced the biotechnology study in Tohoku Electric Power Co. in terms of the above-captioned items. In the study of the plant biotechnology application, with garlic growing as a target, technology to increase seedlings in large quantity by texture cultivation technology was studied. In the biomass utilization study, as to one of the biomass crops, its economical efficiency was studied in case of using it as energy. In the development of the technology to control cold resistance of plant, genes of Superoxide dismutase, etc. were introduced to rice plant to obtain a result which indicates enhancement of cold resistance. In the development of the technology to grow passion fruit, a method was established to grow a tropical fruit, passion fruit produced in Brazil, without heating in winter and to enable two harvests a year, for the contribution to the regional activation. In the study on the identification of useful genes of plant, the development of DNA markers was conducted, trying the identification of a rice blight true resistance gene, Pi-Z{sup t}. 32 figs., 2 tabs.

  15. Handbook of the Infrared Optical Properties of Al2O3. Carbon, MGO and ZrO2. Volume 1

    Science.gov (United States)

    1975-06-04

    J. F. 0., "Influence de la Rugosite Sur Le Rayonnement Thermique Emis Par les Surfaces Opaques: Essai de Modele," Int. Heat Mass Transfer 15, 1451... Transfer 92, 257 (1970). IR-6 Clark, H. E.,and Moore, D, G., "Method and Equipment for0 Measuring Thermal Emittance of Ceramic Oxides from 1200 to 1800 K...K., Bunseki Kagaku. .,, 1050 (1967). 1T-8 Lee, D. W., Kingergy, W. D., "Radiation Energy Transfer and Thermal Conductivity of Ceramic Oxides, " J. Am

  16. JPRS Report, Science & Technology, Japan.

    Science.gov (United States)

    1988-04-13

    Streptococcus equinus 0. 66 ± 0. 01 0.19 0.04 47 Streptococcus mitis 0. 65 ± 0. 01 0.27 0.09 33 Streptococcus salivarius 0. 66 ± 0. 01 0.42 0.15 36...96 Creativity Discussed [Shunichi Akasofu; KAGAKU ASAHI, Au8 87] . 103 TELECOMMUNICATIONS MPT, MITI Proposals (ENERUGI FORAMU, Nov 87) no...it is made up of persons of learning and experience, financial institutions and the like, and MITI -related persons as observers. Furthermore, it has

  17. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Research and development concerning relations between sintered body textural structure and material characteristics in fine ceramics); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (fine ceramics no shoketsutai soshiki kozo to zairyo tokusei tono kankei ni kansuru kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development was carried out involving fine ceramic sintered body textural structure evaluation methods for the development of process technologies for achieving higher quality and lower cost. Studies centered about a method for evaluating coarse pores and coarse grains in sintered bodies, relations between sintered body fracture strength and textural structure, and the standardization of evaluation methods. As the result, an evaluation method for observing pore structures in a sintered body flake specimen under an optical microscope and another for observing coarse grains under a polarization microscope were proposed. As for the effect of coarse defects on the fracture strength of ceramics, it was demonstrated experimentally and theoretically that coarse defects several tens of micrometers in size greatly affected the fracture strength. In the study of methods for sintered body grain size evaluation, findings were obtained about the processing of the specimen surface. (NEDO)

  18. Internal oxidation of ag-Y1Ba2Cu3,-Bi2Sr2Ca1Cu2 and -Bi(1. 8)Pb(0. 3)Sr2Ca2Cu3 alloys, and their resulting superconducting properties. Ag-Y1Ba2Cu3, -Bi2Sr2Ca1Cu2, -Bi(1. 8)Pb(0. 3)Sr2Ca2Cu3 gokin no naibu sanka to sono chodendo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Numazawa, T.; Kimura, H.; Kimura, T.; Fukamachi, M. (National Research Inst. for Metals, Tsukuba, Ibaraki (Japan))

    1994-02-20

    Concerning wire rods for magnets and materials for magnetic shielding, etc. using oxide superconducting substances, studies and development are being made for making the above materials to be composite materials using Ag. In this study, concerning the solute composition of Ag-based alloys, Y1Ba2Cu3, Bi2Sr2Ca1Cu2, and Bi(1.8)Pb(0.3)Sr2Ca2Cu3 have been selected imaging the 123 phase at the Y system, and the 2212 low Tc phase as well as the 2223 high Tc phase at the Bi system. And oxide superconducting substances have been made precipitated in Ag by internal oxidation and thermal treatment of the dissolved alloys compound of Ag-Y1Ba2Cu3, Ag-Bi2Sr2Ca1Cu2, and Ag-Bi(1.8)Pb(0.3)Sr2Ca2Cu3, and its superconducting properties have been studied. Thereby electroconducting paths have been formed by the precipitated oxide superconducting substances and the critical current, though at a low value, has been attained. Also the composition of the above oxide superconducting substances has been image-analyzed from the observation result with an electron beam probe X-ray microanalyzer. With regard to the Ag-Bi(1.8)Pb(0.3)Sr2Ca2Cu3 alloy, precipitation of the single phase of the 2223 phase has not been able to obtain by thermal treatment. 11 refs., 8 figs.

  19. Industrial and scientific technology research and development project fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Report on research and development of a brain type computer architecture `trial fabrication and high-level evaluation on chips for a large-scale artificial neural system` and on results of evaluation studies on the chips; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Nogata computer architecture no kenkyu kaihatsu `daikibo jinko shinkei kairo system yo chip no shisaku to kodo hyoka` chip hyoka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop a brain type computer architecture, a brain mimic processor (BMP) has been developed (which was made in LSI in fiscal 1997), and studies are being made on developing its applications. Development has been made on an element in which linkage of one million cells with one thousand neural cells can be realized. Evaluation substrates mounted with the BMP, control software, and compilers were provided to 15 organizations including the National Research Institutes, universities, corporations, and other societies (for 19 themes) to evaluate capability of the LSI and its application development. All of the research organizations are using these items utilizing features of the LSI or the network for such purposes as learning, storage, recognition and control. The applicable theme may include infrared spectrum pattern recognition and domain division of document images using neural network functions. It can also include structural analysis of mass spectrum molecules, time series pattern recognition, location of corresponding points in images, estimation of moving images, satellite control, character recognition, short time storage, long-term association memory models, and invention process studies, all utilizing the functions of the BMP. 71 refs., 89 figs., 9 tabs.

  20. Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

  1. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  2. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

  3. Assessing the realism of colonoscopy simulation: the development of an instrument and systematic comparison of 4 simulators.

    Science.gov (United States)

    Hill, Andrew; Horswill, Mark S; Plooy, Annaliese M; Watson, Marcus O; Karamatic, Rozemary; Basit, Tabinda A; Wallis, Guy M; Riek, Stephan; Burgess-Limerick, Robin; Hewett, David G

    2012-03-01

    No useful comparative data exist on the relative realism of commercially available devices for simulating colonoscopy. To develop an instrument for quantifying realism and provide the first wide-ranging empiric comparison. Repeated measures, observational study. Nineteen experienced colonoscopists completed cases on 4 colonoscopy simulators (AccuTouch, GI Mentor II, Koken, and Kyoto Kagaku) and evaluated each device. A medical simulation center in a large tertiary hospital. For each device, colonoscopists completed the newly developed Colonoscopy Simulator Realism Questionnaire (CSRQ), which contains 58 items grouped into 10 subscales measuring the realism of different aspects of the simulation. Subscale scores are weighted and combined into an aggregated score, and there is also a single overall realism item. Overall, current colonoscopy simulators were rated as only moderately realistic compared with real human colonoscopy (mean aggregated score, 56.28/100; range, 48.39-60.45, where 0 = "extremely unrealistic" and 100 = "extremely realistic"). On both overall realism measures, the GI Mentor II was rated significantly less realistic than the AccuTouch, Kyoto Kagaku, and Koken (P realism. There is no clear "first choice" simulator among those assessed. Each has unique strengths and weaknesses, reflected in the differing results observed across 9 subscales. These findings may facilitate the targeted selection of simulators for various aspects of colonoscopy training. Copyright © 2012 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.

  4. TH-CD-207B-12: Quantification of Clinical Feedback On Image Quality Differences Between Two CT Scanner Models

    International Nuclear Information System (INIS)

    Bache, S; Liu, X; Loyer, E; Rong, J

    2016-01-01

    Purpose: This work sought to quantify a radiology team’s assessment of image quality differences between two CT scanner models currently in clinical use, with emphasis on noise and low-contrast detectability (LCD). Methods: A water phantom and a Kagaku anthropomorphic body phantom were scanned on GE Discovery CT750 HD and LightSpeed VCT scanners (4 each) with identical scan parameters and reconstructed to 2.5mm/5.0mm thicknesses. Images of water phantom were analyzed at the scanner console with a built-in LCD tool that uses statistical methods to compute requisite CT-number contrast for 95% confidence in detection of a user-defined object size. LCD value was computed for 5mm, 3mm, and 1mm objects. Analysis of standard deviation and LCD values were performed on Kagaku phantom images within liver, stomach, and spleen. LCD value was computed for 4mm, 3mm, and 1mm objects using a benchmarked MATLAB implementation of the GE scanner-console tool. Results: Water LCD values were larger (poorer performance) for all HD scanners compared to VCT scanners. Mean scanner model difference in requisite CT-number contrast for 5mm, 3mm, and 1mm objects for 5.0mm/2.5mm images was 3.0%/3.4% (p=0.02/p=0.10), 5.3%/5.7% (0.00002/0.02), and 8.5%/8.2% (0.0004/0.002), respectively. Mean standard deviations within Kagaku phantom ROIs were greater in HD compared to VCT images, with mean differences for the liver, stomach, and spleen for 5.0mm/2.5mm of 16%/12% (p=0.04/0.10), 8%/12% (0.15/0.11), and 16%/15% (0.05/0.11), respectively. Mean LCD value difference between HD and VCT scanners over all ROIs for 4mm, 3m, and 1mm objects and 5.0mm/2.5mm was 34%/9%, 16%/8%, and 18%/10%, respectively. HD scanners outperformed VCT scanners only for the 4mm stomach object. Conclusion: Using both water and anthropomorphic phantoms, it was shown that HD scanners are outperformed by VCT scanners with respect to noise and LCD in a consistent and in most cases statistically significant manner. The relationship

  5. Assessment of colonoscopy by use of magnetic endoscopic imaging

    DEFF Research Database (Denmark)

    Nerup, Nikolaj; Preisler, Louise; Svendsen, Morten Bo Søndergaard

    2015-01-01

    performance. OBJECTIVE: The aim of this study was to develop and explore the validity of an automated, unbiased assessment tool. DESIGN: We tested 10 experienced endoscopists and 11 trainees in colonoscopy on a physical simulator (Kagaku Colonoscope Training Model). Participants were tested with an easy...... and a difficult case. SETTING: Center for Clinical Education, Capital Region of Denmark. MAIN OUTCOME MEASUREMENTS: By using magnetic endoscopic imaging, we developed a colonoscopy progression score (CoPS). A pass/fail score was established by using the contrast-group method. RESULTS: We found significant...... in the group. The CoPS does not consider polyp detection rate, tissue damage, or patient discomfort. CONCLUSIONS: We developed a score of progression in colonoscopy, based on magnetic endoscopic imaging. With the same tool, a map of progression in colonoscopy can be provided. The CoPS and map of progression...

  6. Chimpanzee pinworm, Enterobius anthropopitheci (Nematoda: Oxyuridae), maintained for more than twenty years in captive chimpanzees in Japan.

    Science.gov (United States)

    Hasegawa, Hideo; Udono, Toshifumi

    2007-08-01

    The chimpanzee pinworm, Enterobius anthropopitheci (Gedoelst, 1916), was found in chimpanzees, Pan troglodytes, reared in Kumamoto Primate Research Park, Sanwa Kagaku Kenkyusho Co., Ltd., Kumamoto, Japan, in 2006. Because the chimpanzees in this institution originated from chimpanzees imported from Africa before 1984, it is considered that E. anthropopitheci infection has persisted for more than 20 yr in the chimpanzees. Analysis of pinworm specimens preserved in the institution revealed that transition of predominant pinworm species occurred, responding to the change of anthelmintics used for pinworm treatment. Present dominance of E. anthropopitheci is surmised to be caused by fenbendazole, which has been adopted from 2002. Scarcity of mixed infection with E. anthropopitheci and Enterobius vermicularis suggests interspecific competition between the pinworms.

  7. Measurements of cosmic radiation doses in civil aircraft by pocket dosimeter. Results for domestic aviation routes in Japan

    International Nuclear Information System (INIS)

    Furukawa, Masahide

    2000-01-01

    The author reported results of cosmic radiation dose measurement done at his tours in civil aircraft by the pocket dosimeter for the purpose to obtain preliminary data. The pocket dosimeter used was of the semiconductor detector (Aloka PDM-101). Measurement was performed in 21 flights of 9 domestic routes ranging from Wakkanai to Miyako-jima and was started during the time from taking off to landing in order to avoid the influence of ground γ-ray. In addition, in 2 flights between Haneda and Wakkanai, neutron dose was measured with Fuji-Denki neutron rem counter NSN10014 and in the 2 flights above and 1 flight between Haneda and Naha, ionization components were measured with NaI(Tl) scintillation spectro-surveymeter (Aloka JSM-102). From results obtained, the equation D=Rc (Tc+10)/60 was gotten: here, D (μSv) was the whole cosmic radiation dose, Tc (min), the time of flight, Rc (μSv/h), the whole component dose rate and that during flying up and down=10 min D. (K.H.)

  8. Background approximation in automatic qualitative X-ray-fluorescent analysis

    International Nuclear Information System (INIS)

    Jordanov, J.; Tsanov, T.; Stefanov, R.; Jordanov, N.; Paunov, M.

    1982-01-01

    An empirical method of finding the dependence of the background intensity (Isub(bg) on the wavelength is proposed, based on the approximation of the experimentally found values for the background in the course of an automatic qualitative X-ray fluorescent analysis with pre-set curve. It is assumed that the dependence I(lambda) will be well approximated by a curve of the type Isub(bg)=(lambda-lambda sub(o)sup(fsub(1)(lambda))exp[fsub(2)(lambda)] where fsub(1) (lambda) and f 2 (lambda) are linear functions with respect to the sought parameters. This assumption was checked out on a ''pure'' starch background, in which it is not known beforehand which points belong to the background. It was assumed that the dependence I(lambda) can be found from all minima in the spectrum. Three types of minima has been distinguished: 1. the lowest point between two well-solved X-ray lines; 2. a minimum obtained as a result of statistical fluctuations of the measured signal; 3. the lowest point between two overlapped lines. The minima strongly deviating from the background are removed from the obtained set. The sum-total of the remaining minima serves as a base for the approximation of the dependence I(lambda). The unknown parameters are determined by means of the LSM. The approximated curve obtained by this method is closer to the real background than the background determined by the method described by Kigaki Denki, as the effect of all recorded minima is taken into account. As an example the PbTe spectrum recorded with crystal LiF 220 is shown graphically. The curve well describes the background of the spectrum even in the regions in which there are no minima belonging to the background. (authors)

  9. Using motion capture to assess colonoscopy experience level.

    Science.gov (United States)

    Svendsen, Morten Bo; Preisler, Louise; Hillingsoe, Jens Georg; Svendsen, Lars Bo; Konge, Lars

    2014-05-16

    To study technical skills of colonoscopists using a Microsoft Kinect™ for motion analysis to develop a tool to guide colonoscopy education. Ten experienced endoscopists (gastroenterologists, n = 2; colorectal surgeons, n = 8) and 11 novices participated in the study. A Microsoft Kinect™ recorded the movements of the participants during the insertion of the colonoscope. We used a modified script from Microsoft to record skeletal data. Data were saved and later transferred to MatLab for analysis and the calculation of statistics. The test was performed on a physical model, specifically the "Kagaku Colonoscope Training Model" (Kyoto Kagaku Co. Ltd, Kyoto, Japan). After the introduction to the scope and colonoscopy model, the test was performed. Seven metrics were analyzed to find discriminative motion patterns between the novice and experienced endoscopists: hand distance from gurney, number of times the right hand was used to control the small wheel of the colonoscope, angulation of elbows, position of hands in relation to body posture, angulation of body posture in relation to the anus, mean distance between the hands and percentage of time the hands were approximated to each other. Four of the seven metrics showed discriminatory ability: mean distance between hands [45 cm for experienced endoscopists (SD 2) vs 37 cm for novice endoscopists (SD 6)], percentage of time in which the two hands were within 25 cm of each other [5% for experienced endoscopists (SD 4) vs 12% for novice endoscopists (SD 9)], the level of the right hand below the sighting line (z-axis) (25 cm for experienced endoscopists vs 36 cm for novice endoscopists, P < 0.05) and the level of the left hand below the z-axis (6 cm for experienced endoscopists vs 15 cm for novice endoscopists, P < 0.05). By plotting the distributions of the percentages for each group, we determined the best discriminatory value between the groups. A pass score was set at the intersection of the distributions, and the

  10. Performance evaluation of iterative reconstruction algorithms for achieving CT radiation dose reduction - a phantom study.

    Science.gov (United States)

    Dodge, Cristina T; Tamm, Eric P; Cody, Dianna D; Liu, Xinming; Jensen, Corey T; Wei, Wei; Kundra, Vikas; Rong, X John

    2016-03-08

    The purpose of this study was to characterize image quality and dose performance with GE CT iterative reconstruction techniques, adaptive statistical iterative recontruction (ASiR), and model-based iterative reconstruction (MBIR), over a range of typical to low-dose intervals using the Catphan 600 and the anthropomorphic Kyoto Kagaku abdomen phantoms. The scope of the project was to quantitatively describe the advantages and limitations of these approaches. The Catphan 600 phantom, supplemented with a fat-equivalent oval ring, was scanned using a GE Discovery HD750 scanner at 120 kVp, 0.8 s rotation time, and pitch factors of 0.516, 0.984, and 1.375. The mA was selected for each pitch factor to achieve CTDIvol values of 24, 18, 12, 6, 3, 2, and 1 mGy. Images were reconstructed at 2.5 mm thickness with filtered back-projection (FBP); 20%, 40%, and 70% ASiR; and MBIR. The potential for dose reduction and low-contrast detectability were evaluated from noise and contrast-to-noise ratio (CNR) measurements in the CTP 404 module of the Catphan. Hounsfield units (HUs) of several materials were evaluated from the cylinder inserts in the CTP 404 module, and the modulation transfer function (MTF) was calculated from the air insert. The results were con-firmed in the anthropomorphic Kyoto Kagaku abdomen phantom at 6, 3, 2, and 1mGy. MBIR reduced noise levels five-fold and increased CNR by a factor of five compared to FBP below 6mGy CTDIvol, resulting in a substantial improvement in image quality. Compared to ASiR and FBP, HU in images reconstructed with MBIR were consistently lower, and this discrepancy was reversed by higher pitch factors in some materials. MBIR improved the conspicuity of the high-contrast spatial resolution bar pattern, and MTF quantification confirmed the superior spatial resolution performance of MBIR versus FBP and ASiR at higher dose levels. While ASiR and FBP were relatively insensitive to changes in dose and pitch, the spatial resolution for MBIR

  11. Construction of the quantitative analysis environment using Monte Carlo simulation

    International Nuclear Information System (INIS)

    Shirakawa, Seiji; Ushiroda, Tomoya; Hashimoto, Hiroshi; Tadokoro, Masanori; Uno, Masaki; Tsujimoto, Masakazu; Ishiguro, Masanobu; Toyama, Hiroshi

    2013-01-01

    The thoracic phantom image was acquisitioned of the axial section to construct maps of the source and density with Monte Carlo (MC) simulation. The phantom was Heart/Liver Type HL (Kyoto Kagaku Co., Ltd.) single photon emission CT (SPECT)/CT machine was Symbia T6 (Siemence) with the collimator LMEGP (low-medium energy general purpose). Maps were constructed from CT images with an in-house software using Visual studio C Sharp (Microsoft). The code simulation of imaging nuclear detectors (SIMIND) was used for MC simulation, Prominence processor (Nihon Medi-Physics) for filter processing and image reconstruction, and the environment DELL Precision T7400 for all image processes. For the actual experiment, the phantom was given 15 MBq of 99m Tc assuming the uptake 2% at the dose of 740 MBq in its myocardial portion and SPECT image was acquisitioned and reconstructed with Butter-worth filter and filter back projection method. CT images were similarly obtained in 0.3 mm thick slices, which were filed in one formatted with digital imaging and communication in medicine (DICOM), and then processed for application to SIMIND for mapping the source and density. Physical and mensuration factors were examined in ideal images by sequential exclusion and simulation of those factors as attenuation, scattering, spatial resolution deterioration and statistical fluctuation. Gamma energy spectrum, SPECT projection and reconstructed images given by the simulation were found to well agree with the actual data, and the precision of MC simulation was confirmed. Physical and mensuration factors were found to be evaluable individually, suggesting the usefulness of the simulation for assessing the precision of their correction. (T.T.)

  12. Renoprotective effects of topiroxostat for hyperuremic patients with overt diabetic nephropathy study (ETUDE Study): A prospective, randomized, multicenter clinical trial.

    Science.gov (United States)

    Mizukoshi, Toshihiro; Kato, Sawako; Ando, Masahiko; Sobajima, Hiroshi; Ohashi, Norimi; Naruse, Tomohiko; Saka, Yosuke; Shimizu, Hideaki; Nagata, Takanobu; Maruyama, Shoichi

    2017-10-09

    We aimed to evaluate the anti-albuminuric effects of topiroxostat in Japanese hyperuricemic patients with diabetic nephropathy. In this 24-week, multicenter, open-label, randomized (1:1) trial, we assigned hyperuricemic patients with diabetic nephropathy (estimated glomerular filtration rate ≥ 20 mL/min/1.73m 2 ) and overt proteinuria (0.3 ≤ urine protein to creatinine ratio (UPCR) <3.5 g/g Cr) to either high dose (160 mg daily) or low dose (40 mg daily) topiroxostat. The primary endpoint was the change in albuminuria indicated by urine albumin-to-creatinine ratio (UACR) from the baseline at the final time point. A total of 80 patients underwent randomization. The changes in UACR after 24 weeks of treatment (or at the final time point if patients failed to reach 24 weeks) relative to the baseline were -122 mg/gCr (95% CI: -5.1 to -240.1, P = 0.041) in patients treated with high dose, while treatment with low dose topiroxostat could not show significant reduction (P = 0.067). In the linear mixed model including baseline albuminuria, eGFR, age, and sex as covariates, the decreases in UACR were still significant from baseline to 12 weeks by 228.7 ± 83.2 mg/gCr (P = 0.0075) in the high dose group. The adverse-event profile during this study was not different between the groups. Topiroxostat 160 mg daily reduced albuminuria in patients with diabetic nephropathy. (Funded by Sanwa Kagaku Kenkyusho; Trial registration, UMIN000015403). This article is protected by copyright. All rights reserved.

  13. Validation study of the thorax phantom Lungman for optimization purposes

    Science.gov (United States)

    Rodríguez Pérez, Sunay; Marshall, Nicholas W.; Struelens, Lara; Bosmans, Hilde

    2017-03-01

    This work aims to investigate the advantages and limitations of the Kyoto Kagaku thorax phantom Lungman for use in chest radiography optimization studies. First, patient survey data were gathered for chest posterior anterior (PA) and lateral (LAT) examinations in a standard chest X-ray room over a period of one year, using a Caesium Iodide (CsI) based flat panel detector with automatic exposure control (AEC). Parameters surveyed included exposure index (EI), dose area product (DAP) and AEC exposure time. PA and LAT projections of the phantom were then compared to these values. Additionally, the equivalence in millimetres of poly (methyl methacrylate) (PMMA) was established for the different regions of the Lungman phantom (lungs and mediastinum). Finally, a voxel model of the Lungman phantom was developed by the segmentation of a volumetric dataset of the phantom acquired using CT scanning. Subsequently, the model was used in Monte Carlo simulations with PENELOPE/penEasy code to calculate the energy deposited in the organs of the phantom. This enabled comparison of the phantom tissue-equivalent materials with materials defined by ICRP 89 in terms of energy deposition. For the survey data, close agreement was found between phantom and the median values for the patient data (deviations ranged from 4% to 31%, one outlier). The phantom lung region is equivalent to 89 mm to 106 mm of PMMA, depending on tube voltage. Energy deposited in the phantom material compared to those for ICRP defined material differed by at most 36% in AP irradiations and 49% in PA irradiations.

  14. Latent class evaluation of a milk test, a urine test, and the fat-to-protein percentage ratio in milk to diagnose ketosis in dairy cows.

    Science.gov (United States)

    Krogh, M A; Toft, N; Enevoldsen, C

    2011-05-01

    In this study, 3 commonly used tests to diagnose ketosis were evaluated with a latent class model to avoid the assumption of an available perfect test. The 3 tests were the KetoLac BHB (Sanwa Kagaku Kenkyusho Co. Ltd., Nagoya, Japan) test strip that tests milk for β-hydroxybutyrate, the KetoStix (Bayer Diagnostics Europe Ltd., Dublin, Ireland) test strip that tests urine for acetoacetate, and the fat-to-protein percentage ratio (FPR) in milk. A total of 8,902 cows were included in the analysis. The cows were considered to be a random sample from the population of Danish dairy cattle under intensive management, thus representing a natural spectrum of ketosis as a disease. All cows had a recorded FPR between 7 and 21 d postpartum. The KetoLac BHB recordings were available from 2,257 cows and 6,645 cows had a KetoStix recording. The recordings were analyzed with a modified Hui-Walter model, in a Bayesian framework. The specificity of the KetoLac BHB test and the KetoStix test were both high [0.99 (0.97-0.99)], whereas the specificity of FPR was somewhat lower [0.79 (0.77-0.81)]. The best sensitivity was for the KetoStix test [0.78 (0.55-0.98)], followed by the FPR [0.63 (0.58-0.71)] and KetoLac BHB test [0.58 (0.35-0.93)]. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  15. Contamination profiles of short-chain polychlorinated n-alkanes in foodstuff samples from Japan

    Energy Technology Data Exchange (ETDEWEB)

    Matsukami, Hidenori; Kurunthachalam, S.; Ohi, Etsumasa; Takasuga, Takumi [Shimadzu Techno Research, Inc., Kyoto (Japan); Iino, Fukuya; Nakanishi, Junko [National Inst. of Advanced Industrial Science and Technology, Tsukuba (Japan)

    2004-09-15

    Polychlorinated n-alkanes (PCAs) are group of chemicals manufactured by chlorination of liquid n-paraffin or paraffin wax that contain 30 to 70% chlorine by weight. Large amounts of PCAs are widely used as plasticizers for vinyl chloride, lubricants, paints, and flame retardants and number of other industrial applications. Annual global production of PCAs is approximately 300 kilo tones, with a majority having medium-carbon-chain (C14-C19) length. According to the investigation made by Kagaku Kogyo Nippon-Sha, the annual consumption of PCAs in Japan was about 83,000 tons in between 1986-2001. Short-carbon-chain (C10-C13) has been placed on the Priority Substance List under Canadian Environmental Protection Act and on the Environmental Protection Agency Toxic Release Inventory in the USA due to its potential to act as tumor promoters in mammals. Data on environment levels of PCAs is meager, nevertheless, PCAs have been measured at relatively high concentrations in biota from Sweden, biota, sediment from Canada and marine biota and human milk from the Canadian Arctic. In our earlier study, we reported concentrations of short-chain PCAs from sewage treatment plant (STP) collected from Tama River, Tokyo and river water and sediment from Tokyo and Osaka. STP influent water contained greater shortchain PCAs concentrations than STP effluent. In addition, some river water and sediment samples contained detectable concentrations of short-chain PCAs, which was similar to other industrial countries. However, there is no study conducted to explore the contamination profiles of short-chain PCAs in human foodstuff samples. In the present study, we analyzed eleven foodstuff samples that were purchased from various supermarkets in order to know the short-chain PCAs concentrations in the foodstuff and possible human total daily intake (TDI) amounts.

  16. Evaluation of a transfer system for calibration of kVp meters and ionization chambers

    International Nuclear Information System (INIS)

    Potiens, M.P.A.; Caldas, L.V.E.

    2002-01-01

    The assessment and control of the performance characteristics of X-ray generators and tubes is an essential part of a quality assurance programme, because the use of the X-rays in medicine for diagnosis of injuries and diseases represents the largest man-made source of public exposure to ionizing radiation. Others authors have suggested methods to determine the correct X-ray tube voltage to complete the characterization of standard radiation qualities. A method by spectrometry to calibrate ionization chambers and kVp meters used for quality control tests in diagnostic radiology has been applied at the Calibration Laboratory at IPEN. A transfer system for diagnostic radiology calibration was developed at IPEN as an alternative to calibrate those instruments that measure kVp and air kerma values. It consists of a pair of identical ionization chambers in form, but differing only by the electrode material: one is made of aluminum, and the other is made of graphite. It was calibrated using a spectrometer and a standard ionization chamber traceable to the German Primary Laboratory (Physikalisch-Technische Bundesanstalt - PTB). In this study the behaviour of the transfer system was analysed in the standard beams of two X-ray equipment of the Calibration Laboratory. The low energy X-ray generating system consists of a Rigaku Denki generator, model Geigerflex, coupled to a Philips tube model PW/2184/00 (Tungsten target and Beryllium window). Measurements were taken from 30 to 50 kV. The diagnostic radiology X-ray generating system consists of a Medicor Moevek Roentgengyara X-ray generator, model Neo-Diagnomax (125 kV). Measurements were taken from 50 to 90 kV. The established qualities are listed. As reference to the air kerma rate determination, a 1.0 cm 3 parallel plate ionization chamber, Physikalisch-Technische Werkstaetten (PTW), model 77334, traceable to PTB, Germany, was utilized in this work. The transfer system was placed in the X-ray beams, using a Lucite holder

  17. A stylized computational model of the head for the reference Japanese male

    International Nuclear Information System (INIS)

    Yamauchi, M.; Ishikawa, M.; Hoshi, M.

    2005-01-01

    Computational models of human anatomy, along with Monte Carlo radiation transport simulations, have been used by Snyder et al. [MIRD Pamphlet No. 5, revised (The Society of Nuclear Medicine, New York, 1978)], Cristy and Eckerman [ORNL/TM-8381/VI, Oak Ridge National Laboratory, Oak Ridge, TN (1987)] and Zubal et al. [Med. Phys. 21, 299-302 (1994)] to estimate internal organ doses from internal and external radiation sources. These were created using physiological data from Caucasoid subjects but not from other races. There is a need for research to determine whether the obvious differences from the Caucasoid anatomy make these models unsuitable for estimating the absorbed dose in other races such as the Mongoloid. We used the cranial region of the adult Japanese male to represent the Mongoloid race. This region contains organs that are highly sensitive to radiation. The cranial region of a physical phantom produced by KYOTO KAGAKU Co., LTD. using numerical data from a Japanese Reference Man [Tanaka, Nippon Acta. Radiol. 48, 509-513 (1988)] was used to supply the data for the geometry of a stylized computational model. Our computational model was constructed with equations rather than voxel-based, in order to deal with as small a number of parameters as possible in the computer simulation experiment. The accuracy of our computational model was checked by comparing simulated experimental results obtained with MCNP4C with actual doses measured with thermoluminescence dosimeters (TLDs) inside the physical phantom from which our computational model was constructed. The TLDs, whose margin of error is less than ±10%, were arranged at six positions. Co-60 was used as the radiation source. The irradiated dose was 2 Gy in terms of air kerma. In the computer simulation experiments, we used our computational model and Cristy's computational model, whose component data are those of the tissue substitute materials and of the human body as published in ICRU Report 46. The

  18. SU-F-J-16: Planar KV Imaging Dose Reduction Study

    Energy Technology Data Exchange (ETDEWEB)

    Gershkevitsh, E; Zolotuhhin, D [North Estonia Medical Centre, Tallinn (Estonia)

    2016-06-15

    Purpose: IGRT has become an indispensable tool in modern radiotherapy with kV imaging used in many departments due to superior image quality and lower dose when compared to MV imaging. Many departments use manufacturer supplied protocols for imaging which are not always optimised between image quality and radiation dose (ALARA). Methods: Whole body phantom PBU-50 (Kyoto Kagaku ltd., Japan) for imaging in radiology has been imaged on Varian iX accelerator (Varian Medical Systems, USA) with OBI 1.5 system. Manufacturer’s default protocols were adapted by modifying kV and mAs values when imaging different anatomical regions of the phantom (head, thorax, abdomen, pelvis, extremities). Images with different settings were independently reviewed by two persons and their suitability for IGRT set-up correction protocols were evaluated. The suitable images with the lowest mAs were then selected. The entrance surface dose (ESD) for manufacturer’s default protocols and modified protocols were measured with RTI Black Piranha (RTI Group, Sweden) and compared. Image quality was also measured with kVQC phantom (Standard Imaging, USA) for different protocols. The modified protocols have been applied for clinical work. Results: For most cases optimized protocols reduced the ESD on average by a factor of 3(range 0.9–8.5). Further reduction in ESD has been observed by applying bow-tie filter designed for CBCT. The largest reduction in dose (12.2 times) was observed for Thorax lateral protocol. The dose was slightly increased (by 10%) for large pelvis AP protocol. Conclusion: Manufacturer’s default IGRT protocols could be optimised to reduce the ESD to the patient without losing the necessary image quality for patient set-up correction. For patient set-up with planar kV imaging the bony anatomy is mostly used and optimization should focus on this aspect. Therefore, the current approach with anthropomorphic phantom is more advantageous in optimization over standard kV quality

  19. A field study to determine the prevalence, dairy herd management systems, and fresh cow clinical conditions associated with ketosis in western European dairy herds.

    Science.gov (United States)

    Berge, Anna C; Vertenten, Geert

    2014-01-01

    The aim of this study was to determine the prevalence, major management systems, and fresh cow clinical conditions associated with ketosis in western European dairy herds. A total of 131 dairies were enrolled in Germany, France, Italy, the Netherlands, and the United Kingdom during 2011 to 2012. A milk-based test for ketones (Keto-Test; Sanwa Kagaku Kenkyusho Co. Ltd., Nagoya, Japan; distributed by Elanco Animal Health, Antwerp, Belgium) was used for screening cows between d 7 and 21 after calving and ketosis was defined as a Keto-Test ≥100µmol/L. Study cows were observed for clinical disease up to 35d postcalving. Multivariate analysis (generalized estimating equation logistic regression) was performed to determine country, farm, management, feed, and cow factors associated with ketosis and to determine associations between ketosis and fresh cow diseases. Thirty-nine percent of the cows were classified as having ketosis. The herd average of ketosis was 43% in Germany, 53% in France, 31% in Italy, 46% in the Netherlands, and 31% in the United Kingdom. Of the 131 farms, 112 (85%) had 25% or more of their fresh cows resulting as positive for ketosis. Clinical ketosis was not reported in most farms and the highest level of clinical ketosis reported was 23%. The risks of ketosis were significantly lower in Italy and the United Kingdom compared with France, the Netherlands, and Germany. Larger herd size was associated with a decreased risk of ketosis. The farms that fed partially mixed rations had 1.5 times higher odds of ketosis than those that fed total mixed rations. Cows that calved in April to June had the highest odds of ketosis, with about twice as high odds compared with cows that calved in July to September. The cows that calved in January to March tended to have 1.5 times higher risk of ketosis compared with cows that calved in July to September. The odds of ketosis in parity 2 and parity 3 to 7 was significantly higher (1.5 and 2.8 times higher

  20. Quantitative comparison of commercial and non-commercial metal artifact reduction techniques in computed tomography.

    Directory of Open Access Journals (Sweden)

    Dirk Wagenaar

    Full Text Available Typical streak artifacts known as metal artifacts occur in the presence of strongly attenuating materials in computed tomography (CT. Recently, vendors have started offering metal artifact reduction (MAR techniques. In addition, a MAR technique called the metal deletion technique (MDT is freely available and able to reduce metal artifacts using reconstructed images. Although a comparison of the MDT to other MAR techniques exists, a comparison of commercially available MAR techniques is lacking. The aim of this study was therefore to quantify the difference in effectiveness of the currently available MAR techniques of different scanners and the MDT technique.Three vendors were asked to use their preferential CT scanner for applying their MAR techniques. The scans were performed on a Philips Brilliance ICT 256 (S1, a GE Discovery CT 750 HD (S2 and a Siemens Somatom Definition AS Open (S3. The scans were made using an anthropomorphic head and neck phantom (Kyoto Kagaku, Japan. Three amalgam dental implants were constructed and inserted between the phantom's teeth. The average absolute error (AAE was calculated for all reconstructions in the proximity of the amalgam implants.The commercial techniques reduced the AAE by 22.0±1.6%, 16.2±2.6% and 3.3±0.7% for S1 to S3 respectively. After applying the MDT to uncorrected scans of each scanner the AAE was reduced by 26.1±2.3%, 27.9±1.0% and 28.8±0.5% respectively. The difference in efficiency between the commercial techniques and the MDT was statistically significant for S2 (p=0.004 and S3 (p<0.001, but not for S1 (p=0.63.The effectiveness of MAR differs between vendors. S1 performed slightly better than S2 and both performed better than S3. Furthermore, for our phantom and outcome measure the MDT was more effective than the commercial MAR technique on all scanners.

  1. Techniques for virtual lung nodule insertion: volumetric and morphometric comparison of projection-based and image-based methods for quantitative CT

    Science.gov (United States)

    Robins, Marthony; Solomon, Justin; Sahbaee, Pooyan; Sedlmair, Martin; Choudhury, Kingshuk Roy; Pezeshk, Aria; Sahiner, Berkman; Samei, Ehsan

    2017-09-01

    Virtual nodule insertion paves the way towards the development of standardized databases of hybrid CT images with known lesions. The purpose of this study was to assess three methods (an established and two newly developed techniques) for inserting virtual lung nodules into CT images. Assessment was done by comparing virtual nodule volume and shape to the CT-derived volume and shape of synthetic nodules. 24 synthetic nodules (three sizes, four morphologies, two repeats) were physically inserted into the lung cavity of an anthropomorphic chest phantom (KYOTO KAGAKU). The phantom was imaged with and without nodules on a commercial CT scanner (SOMATOM Definition Flash, Siemens) using a standard thoracic CT protocol at two dose levels (1.4 and 22 mGy CTDIvol). Raw projection data were saved and reconstructed with filtered back-projection and sinogram affirmed iterative reconstruction (SAFIRE, strength 5) at 0.6 mm slice thickness. Corresponding 3D idealized, virtual nodule models were co-registered with the CT images to determine each nodule’s location and orientation. Virtual nodules were voxelized, partial volume corrected, and inserted into nodule-free CT data (accounting for system imaging physics) using two methods: projection-based Technique A, and image-based Technique B. Also a third Technique C based on cropping a region of interest from the acquired image of the real nodule and blending it into the nodule-free image was tested. Nodule volumes were measured using a commercial segmentation tool (iNtuition, TeraRecon, Inc.) and deformation was assessed using the Hausdorff distance. Nodule volumes and deformations were compared between the idealized, CT-derived and virtual nodules using a linear mixed effects regression model which utilized the mean, standard deviation, and coefficient of variation (Mea{{n}RHD} , ST{{D}RHD} and C{{V}RHD}{) }~ of the regional Hausdorff distance. Overall, there was a close concordance between the volumes of the CT-derived and

  2. Techniques for virtual lung nodule insertion: volumetric and morphometric comparison of projection-based and image-based methods for quantitative CT.

    Science.gov (United States)

    Robins, Marthony; Solomon, Justin; Sahbaee, Pooyan; Sedlmair, Martin; Roy Choudhury, Kingshuk; Pezeshk, Aria; Sahiner, Berkman; Samei, Ehsan

    2017-08-22

    Virtual nodule insertion paves the way towards the development of standardized databases of hybrid CT images with known lesions. The purpose of this study was to assess three methods (an established and two newly developed techniques) for inserting virtual lung nodules into CT images. Assessment was done by comparing virtual nodule volume and shape to the CT-derived volume and shape of synthetic nodules. 24 synthetic nodules (three sizes, four morphologies, two repeats) were physically inserted into the lung cavity of an anthropomorphic chest phantom (KYOTO KAGAKU). The phantom was imaged with and without nodules on a commercial CT scanner (SOMATOM Definition Flash, Siemens) using a standard thoracic CT protocol at two dose levels (1.4 and 22 mGy CTDI vol ). Raw projection data were saved and reconstructed with filtered back-projection and sinogram affirmed iterative reconstruction (SAFIRE, strength 5) at 0.6 mm slice thickness. Corresponding 3D idealized, virtual nodule models were co-registered with the CT images to determine each nodule's location and orientation. Virtual nodules were voxelized, partial volume corrected, and inserted into nodule-free CT data (accounting for system imaging physics) using two methods: projection-based Technique A, and image-based Technique B. Also a third Technique C based on cropping a region of interest from the acquired image of the real nodule and blending it into the nodule-free image was tested. Nodule volumes were measured using a commercial segmentation tool (iNtuition, TeraRecon, Inc.) and deformation was assessed using the Hausdorff distance. Nodule volumes and deformations were compared between the idealized, CT-derived and virtual nodules using a linear mixed effects regression model which utilized the mean, standard deviation, and coefficient of variation ([Formula: see text], [Formula: see text] and [Formula: see text] of the regional Hausdorff distance. Overall, there was a close concordance between the volumes of

  3. Techniques for virtual lung nodule insertion: volumetric and morphometric comparison of projection-based and image-based methods for quantitative CT

    Science.gov (United States)

    Robins, Marthony; Solomon, Justin; Sahbaee, Pooyan; Sedlmair, Martin; Choudhury, Kingshuk Roy; Pezeshk, Aria; Sahiner, Berkman; Samei, Ehsan

    2017-01-01

    Virtual nodule insertion paves the way towards the development of standardized databases of hybrid CT images with known lesions. The purpose of this study was to assess three methods (an established and two newly developed techniques) for inserting virtual lung nodules into CT images. Assessment was done by comparing virtual nodule volume and shape to the CT-derived volume and shape of synthetic nodules. 24 synthetic nodules (three sizes, four morphologies, two repeats) were physically inserted into the lung cavity of an anthropomorphic chest phantom (KYOTO KAGAKU). The phantom was imaged with and without nodules on a commercial CT scanner (SOMATOM Definition Flash, Siemens) using a standard thoracic CT protocol at two dose levels (1.4 and 22 mGy CTDIvol). Raw projection data were saved and reconstructed with filtered back-projection and sinogram affirmed iterative reconstruction (SAFIRE, strength 5) at 0.6 mm slice thickness. Corresponding 3D idealized, virtual nodule models were co-registered with the CT images to determine each nodule’s location and orientation. Virtual nodules were voxelized, partial volume corrected, and inserted into nodule-free CT data (accounting for system imaging physics) using two methods: projection-based Technique A, and image-based Technique B. Also a third Technique C based on cropping a region of interest from the acquired image of the real nodule and blending it into the nodule-free image was tested. Nodule volumes were measured using a commercial segmentation tool (iNtuition, TeraRecon, Inc.) and deformation was assessed using the Hausdorff distance. Nodule volumes and deformations were compared between the idealized, CT-derived and virtual nodules using a linear mixed effects regression model which utilized the mean, standard deviation, and coefficient of variation (MeanRHD, and STDRHD CVRHD) of the regional Hausdorff distance. Overall, there was a close concordance between the volumes of the CT-derived and virtual nodules

  4. SU-E-I-22: Dependence On Calibration Phantom and Field Area of the Conversion Factor Used to Calculate Skin Dose During Neuro-Interventional Fluoroscopic Procedures

    International Nuclear Information System (INIS)

    Rana, V K; Vijayan, S; Rudin, S R; Bednarek, D R

    2014-01-01

    Purpose: To determine the appropriate calibration factor to use when calculating skin dose with our real-time dose-tracking system (DTS) during neuro-interventional fluoroscopic procedures by evaluating the difference in backscatter from different phantoms and as a function of entrance-skin field area. Methods: We developed a dose-tracking system to calculate and graphically display the cumulative skin-dose distribution in real time. To calibrate the DTS for neuro-interventional procedures, a phantom is needed that closely approximates the scattering properties of the head. We compared the x-ray backscatter from eight phantoms: 20-cm-thick solid water, 16-cm diameter water-filled container, 16-cm CTDI phantom, modified-ANSI head phantom, 20-cm-thick PMMA, Kyoto-Kagaku PBU- 50 head, Phantom-Labs SK-150 head, and RSD RS-240T head. The phantoms were placed on the patient table with the entrance surface at 15 cm tube-side from the isocenter of a Toshiba Infinix C-arm, and the entrance-skin exposure was measured with a calibrated 6-cc PTW ionization chamber. The measurement included primary radiation, backscatter from the phantom and forward scatter from the table and pad. The variation in entrance-skin exposure was also measured as a function of the skin-entrance area for a 30x30 cm by 20-cm-thick PMMA phantom and the SK-150 head phantom using four different added beam filters. Results: The entranceskin exposure values measured for eight different phantoms differed by up to 12%, while the ratio of entrance exposure of all phantoms relative to solid water showed less than 3% variation with kVp. The change in entrance-skin exposure with entrance-skin area was found to differ for the SK-150 head compared to the 20-cm PMMA phantom and the variation with field area was dependent on the added beam filtration. Conclusion: To accurately calculate skin dose for neuro-interventional procedures with the DTS, the phantom for calibration should be carefully chosen since different