WorldWideScience

Sample records for demonstrate process uniformity

  1. Radiative processes of uniformly accelerated entangled atoms

    CERN Document Server

    Menezes, G

    2015-01-01

    We study radiative processes of uniformly accelerated entangled atoms, interacting with an electromagnetic field prepared in the Minkowski vacuum state. We discuss the structure of the rate of variation of the atomic energy for two atoms travelling in different hyperbolic world lines. We identify the contributions of vacuum fluctuations and radiation reaction to the generation of entanglement as well as to the decay of entangled states. Our results resemble the situation in which two inertial atoms are coupled individually to two spatially separated cavities at different temperatures. In addition, for equal accelerations we obtain that the maximally entangled antisymmetric Bell state is a decoherence-free state.

  2. The Edgewater Coolside process demonstration

    Energy Technology Data Exchange (ETDEWEB)

    McCoy, D.C.; Scandrol, R.O.; Statnick, R.M.; Stouffer, M.R.; Winschel, R.A.; Withum, J.A.; Wu, M.M.; Yoon, H. [CONSOL, Inc., Pittsburgh, PA (United States)

    1992-02-01

    The Edgewater Coolside process demonstration met the program objectives which were to determine Coolside SO{sub 2} removal performance, establish short-term process operability, and evaluate the economics of the process versus a limestone wet scrubber. On a flue gas produced from the combustion of 3% sulfur coal, the Coolside process achieved 70% SO{sub 2} removal using commercially-available hydrated lime as the sorbent. The operating conditions were Ca/S mol ratio 2.0, Na/Ca mol ratio 0.2, and 20{degree}F approach to adiabatic saturation temperature ({del}T). During tests using fresh plus recycle sorbent, the recycle sorbent exhibited significant capacity for additional SO{sub 2} removal. The longest steady state operation was eleven days at nominally Ca/S = 2, Na/Ca = 0.22, {del}T = 20--22{degree}F, and 70% SO{sub 2} removal. The operability results achieved during the demonstration indicate that with the recommended process modifications, which are discussed in the Coolside process economic analysis, the process could be designed as a reliable system for utility application. Based on the demonstration program, the Coolside process capital cost for a hypothetical commercial installation was minimized. The optimization consisted of a single, large humidifier, no spare air compressor, no isolation dampers, and a 15 day on-site hydrated lime storage. The levelized costs of the Coolside and the wet limestone scrubbing processes were compared. The Coolside process is generally economically competitive with wet scrubbing for coals containing up to 2.5% sulfur and plants under 350 MWe. Site-specific factors such as plant capacity factor, SO{sub 2} emission limit, remaining plant life, retrofit difficulty, and delivered sorbent cost affect the scrubber-Coolside process economic comparison.

  3. The Edgewater Coolside process demonstration

    Energy Technology Data Exchange (ETDEWEB)

    McCoy, D.C.; Scandrol, R.O.; Statnick, R.M.; Stouffer, M.R.; Winschel, R.A.; Withum, J.A.; Wu, M.M.; Yoon, H. (CONSOL, Inc., Pittsburgh, PA (United States))

    1992-02-01

    The Edgewater Coolside process demonstration met the program objectives which were to determine Coolside SO[sub 2] removal performance, establish short-term process operability, and evaluate the economics of the process versus a limestone wet scrubber. On a flue gas produced from the combustion of 3% sulfur coal, the Coolside process achieved 70% SO[sub 2] removal using commercially-available hydrated lime as the sorbent. The operating conditions were Ca/S mol ratio 2.0, Na/Ca mol ratio 0.2, and 20[degree]F approach to adiabatic saturation temperature ([del]T). During tests using fresh plus recycle sorbent, the recycle sorbent exhibited significant capacity for additional SO[sub 2] removal. The longest steady state operation was eleven days at nominally Ca/S = 2, Na/Ca = 0.22, [del]T = 20--22[degree]F, and 70% SO[sub 2] removal. The operability results achieved during the demonstration indicate that with the recommended process modifications, which are discussed in the Coolside process economic analysis, the process could be designed as a reliable system for utility application. Based on the demonstration program, the Coolside process capital cost for a hypothetical commercial installation was minimized. The optimization consisted of a single, large humidifier, no spare air compressor, no isolation dampers, and a 15 day on-site hydrated lime storage. The levelized costs of the Coolside and the wet limestone scrubbing processes were compared. The Coolside process is generally economically competitive with wet scrubbing for coals containing up to 2.5% sulfur and plants under 350 MWe. Site-specific factors such as plant capacity factor, SO[sub 2] emission limit, remaining plant life, retrofit difficulty, and delivered sorbent cost affect the scrubber-Coolside process economic comparison.

  4. Uniform dimension results of multi-parameter stable processes

    Institute of Scientific and Technical Information of China (English)

    林火南

    1999-01-01

    The problem of uniform dimensions for multi-parameter processes, which may not possess the uniform stochastic H(?)lder condition, is investigated. The problem of uniform dimension for multi-parameter stable processes is solved. That is, if Z is a stable (N, d, α)-process and αN≤d, then (?)E(?)R_+~N, dimZ(E)=α·dimE holds with probability 1, where Z(E)={x:(?)t∈E, Z_t=x} is the image set of Z on E. The uniform upper bounds for multi-parameter processes with independent increments under general conditions are also given. Most conclusions about uniform dimension can be considered as special cases of our results.

  5. UNIFORM PACKING DIMENSION RESULTS FOR MULTIPARAMETER STABLE PROCESSES

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this article, authors discuss the problem of uniform packing dimension of the image set of multiparameter stochastic processes without random uniform H(o)lder condition, and obtain the uniform packing dimension of multiparameter stable processes.If Z is a stable (N, d, α)-process and αN ≤ d, then the following holds with probability 1 Dim Z(E) = α DimE for any Borel setE ∈ B(R+N),where Z(E) = {x: (E) t ∈ E, Z(t) = x}. Dim(E) denotes the packing dimension of E.

  6. How current ginning processes affect fiber length uniformity index

    Science.gov (United States)

    There is a need to develop cotton ginning methods that improve fiber characteristics that are compatible with the newer and more efficient spinning technologies. A literature search produced recent studies that described how current ginning processes affect HVI fiber length uniformity index. Resul...

  7. ISHIKAWA ITERATIVE PROCESS IN UNIFORMLY SMOOTH BANACH SPACES

    Institute of Scientific and Technical Information of China (English)

    黄震宇

    2001-01-01

    Let E be a uniformly smooth Banach space, K be a nonempty closed convex subset of E, and suppose: T: K → K is a continuous φ-strongly pseudocontractive operator with a bounded range. Using a new analytical method, under general cases, the Ishikawa iterative process { xn } converges strongly to the unique fixed point x * of the operator Twere proved. The paper generalizes and extends a lot of recent corresponding results.

  8. Uniform color processing of scanned topographic maps based on SSR

    Science.gov (United States)

    Fu, Zhongliang; Tong, Chunya; Liu, Lu; Huang, Yan

    2009-10-01

    Nowadays, large amount of paper-based topographic maps are still existed in many government department. The scanned maps of them are very useful for research on city history migration, city planning and so on. However, the brightness of these maps is not uniform, and creases are existed, so uniform color process is always needed. If the classical Retinex algorithm is used, the map would have a low brightness and contrast ratio. Therefore, a normal intercepting SSR algorithm of linear extending is presented in this paper. This algorithm first uses the classical SSR algorithm to process the data, and then the average value of image and variance are introduced to do normal intercepting linear extending on the map. Experiment results show that, the improved SSR can not only efficiently eliminate creases and uniform the map brightness, but also increase the global brightness and contrast ratio. Moreover, this algorithm can also be used in the pretreatment of grid image registration, thus to enhance the precision, velocity and accuracy of registration.

  9. schwimmbad: A uniform interface to parallel processing pools in Python

    Science.gov (United States)

    Price-Whelan, Adrian M.; Foreman-Mackey, Daniel

    2017-09-01

    Many scientific and computing problems require doing some calculation on all elements of some data set. If the calculations can be executed in parallel (i.e. without any communication between calculations), these problems are said to be perfectly parallel. On computers with multiple processing cores, these tasks can be distributed and executed in parallel to greatly improve performance. A common paradigm for handling these distributed computing problems is to use a processing "pool": the "tasks" (the data) are passed in bulk to the pool, and the pool handles distributing the tasks to a number of worker processes when available. schwimmbad provides a uniform interface to parallel processing pools and enables switching easily between local development (e.g., serial processing or with multiprocessing) and deployment on a cluster or supercomputer (via, e.g., MPI or JobLib).

  10. Interactive Image Processing demonstrations for the web

    OpenAIRE

    Tella Amo, Marcel

    2011-01-01

    The main goal in this project is to improve the way how image processing developers can test their algorithms, and show them to other people to demonstrate their performance. This diploma thesis aims to provide a framework for developing web applications for ImagePlus, the software develpment platform in C++ of the Image Processing Group of the Technical University of Catalonia (UPC). These web applications are to demonstrate the functionality of the image processing algorithms to any ...

  11. Experiments To Demonstrate Chemical Process Safety Principles.

    Science.gov (United States)

    Dorathy, Brian D.; Mooers, Jamisue A.; Warren, Matthew M.; Mich, Jennifer L.; Murhammer, David W.

    2001-01-01

    Points out the need to educate undergraduate chemical engineering students on chemical process safety and introduces the content of a chemical process safety course offered at the University of Iowa. Presents laboratory experiments demonstrating flammability limits, flash points, electrostatic, runaway reactions, explosions, and relief design.…

  12. Demonstration of a stable and uniform single-wavelength erbium-doped fiber laser based on microfiber knot resonator

    Science.gov (United States)

    Xu, Yiping; Ren, Liyong; Ma, Chengju; Kong, Xudong; Ren, Kaili

    2016-12-01

    We propose and demonstrate an application of microfiber knot resonator (MKR) in the generation of a stable and uniform single-wavelength erbium-doped fiber laser (EDFL). An MKR was fabricated using a microfiber a few micrometers in diameter. By embedding the MKR to the ring cavity of the EDFL, a laser with a wavelength of 1558.818 nm and a 3-dB linewidth of 0.0149 nm is demonstrated. The side mode suppression ratio of the laser is about 30 dB, and the maximum power fluctuation is about 0.85 dB. The results demonstrate that the MKR can be employed as a high-performance comb filter to realize a stable and uniform fiber laser.

  13. Leveraging Non-Uniform Resources for Parallel Query Processing

    DEFF Research Database (Denmark)

    Mayr, Tobias; Bonnet, Philippe; Gehrke, Johannes

    2003-01-01

    Modular clusters are now composed of non- uniform nodes with different CPUs, disks or network cards so that customers can adapt the cluster configuration to the changing technologies and to their changing needs. This challenges dataflow parallelism as the primary load balancing technique of exist......Modular clusters are now composed of non- uniform nodes with different CPUs, disks or network cards so that customers can adapt the cluster configuration to the changing technologies and to their changing needs. This challenges dataflow parallelism as the primary load balancing technique...

  14. C. elegans Demonstrates Distinct Behaviors within a Fixed and Uniform Electric Field.

    Science.gov (United States)

    Chrisman, Steven D; Waite, Christopher B; Scoville, Alison G; Carnell, Lucinda

    2016-01-01

    C. elegans will orient and travel in a straight uninterrupted path directly towards the negative pole of a DC electric field. We have sought to understand the strategy worms use to navigate to the negative pole in a uniform electric field that is fixed in both direction and magnitude. We examined this behavior by quantifying three aspects of electrotaxis behavior in response to different applied field strengths: the mean approach trajectory angles of the animals' tracks, turning behavior (pirouettes) and average population speeds. We determined that C. elegans align directly to the negative pole of an electric field at sub-preferred field strength and alter approach trajectories at higher field strengths to maintain taxis within a preferred range we have calculated to be ~ 5V/cm. We sought to identify the sensory neurons responsible for the animals' tracking to a preferred field strength. eat-4 mutant animals defective in glutamatergic signaling of the amphid sensory neurons are severely electrotaxis defective and ceh-36 mutant animals, which are defective in the terminal differentiation of two types of sensory neurons, AWC and ASE, are partially defective in electrotaxis. To further elucidate the role of the AWC neurons, we examined the role of each of the pair of AWC neurons (AWCOFF and AWCON), which are functionally asymmetric and express different genes. nsy-5/inx-19 mutant animals, which express both neurons as AWCOFF, are severely impaired in electrotaxis behavior while nsy-1 mutants, which express both neurons as AWCON, are able to differentiate field strengths required for navigation to a specific field strength within an electric field. We also tested a strain with targeted genetic ablation of AWC neurons and found that these animals showed only slight disruption of directionality and turning behavior. These results suggest a role for AWC neurons in which complete loss of function is less disruptive than loss of functional asymmetry in electrotaxis

  15. Electrical and optical characterization of an atmospheric pressure, uniform, large-area processing, dielectric barrier discharge

    Science.gov (United States)

    Zeniou, A.; Puač, N.; Škoro, N.; Selaković, N.; Dimitrakellis, P.; Gogolides, E.; Petrović, Z. Lj

    2017-04-01

    A printed-circuit-board (PCB) based atmospheric pressure dielectric barrier discharge (DBD) capable of uniform processing over a large area was constructed consisting of two parallel plates. The first perforated plate is comprised of four layers: a RF powered metal layer, a polymeric dielectric layer, a floating metal grid and another dielectric layer. The second, grounded, plate was fluorine doped tin oxide (FTO) glass plate with surface of 100  ×  100 mm2 and thickness of 2 mm. The PCB based atmospheric pressure DBD was characterized by (a) measuring electrical characteristics of the device using derivative I-V probes, (b) ICCD imaging and (c) optical emission spectroscopy (OES). Optical and electrical characteristics, as well as plasma uniformity were measured by changing He flow rate and input power, while keeping the gap between the PCB and the FTO glass plate ground electrode constant at 2 mm. The plasma uniformity strongly depends on the applied power and on the flow rate of the buffer gas. When increasing the flow rate, the intensity of the nitrogen-dominated emission drops, while emission of helium and oxygen lines increases. The source allows low temperature, uniform plasma operation over a wide area of 100  ×  100 mm2, which could be essential for numerous applications. Examples of etching rate and hydrophilization are demonstrated.

  16. Leveraging Non-Uniform Resources for Parallel Query Processing

    DEFF Research Database (Denmark)

    Mayr, Tobias; Bonnet, Philippe; Gehrke, Johannes;

    2003-01-01

    of existing parallel database systems. We show in this paper that dataflow parallelism alone is ill suited for modular clusters because running the same operation on different subsets of the data can not fully utilize non-uniform hardware resources. We propose and evaluate new load balancing techniques......Modular clusters are now composed of non- uniform nodes with different CPUs, disks or network cards so that customers can adapt the cluster configuration to the changing technologies and to their changing needs. This challenges dataflow parallelism as the primary load balancing technique...... that confirms the feasibility and effectiveness of the new techniques in a parallel execution engine prototype based on the open-source DBMS Predator....

  17. Integration Process for the Habitat Demonstration Unit

    Science.gov (United States)

    Gill, Tracy; Merbitz, Jerad; Kennedy, Kriss; Tn, Terry; Toups, Larry; Howe, A. Scott; Smitherman, David

    2011-01-01

    The Habitat Demonstration Unit (HDU) is an experimental exploration habitat technology and architecture test platform designed for analog demonstration activities. The HDU previously served as a test bed for testing technologies and sub-systems in a terrestrial surface environment. in 2010 in the Pressurized Excursion Module (PEM) configuration. Due to the amount of work involved to make the HDU project successful, the HDU project has required a team to integrate a variety of contributions from NASA centers and outside collaborators The size of the team and number of systems involved With the HDU makes Integration a complicated process. However, because the HDU shell manufacturing is complete, the team has a head start on FY--11 integration activities and can focus on integrating upgrades to existing systems as well as integrating new additions. To complete the development of the FY-11 HDU from conception to rollout for operations in July 2011, a cohesive integration strategy has been developed to integrate the various systems of HDU and the payloads. The highlighted HDU work for FY-11 will focus on performing upgrades to the PEM configuration, adding the X-Hab as a second level, adding a new porch providing the astronauts a larger work area outside the HDU for EVA preparations, and adding a Hygiene module. Together these upgrades result in a prototype configuration of the Deep Space Habitat (DSH), an element under evaluation by NASA's Human Exploration Framework Team (HEFT) Scheduled activates include early fit-checks and the utilization of a Habitat avionics test bed prior to installation into HDU. A coordinated effort to utilize modeling and simulation systems has aided in design and integration concept development. Modeling tools have been effective in hardware systems layout, cable routing, sub-system interface length estimation and human factors analysis. Decision processes on integration and use of all new subsystems will be defined early in the project to

  18. Demonstration of uniformity of calcium absorption in adult dogs and cats.

    Science.gov (United States)

    Mack, J K; Alexander, L G; Morris, P J; Dobenecker, B; Kienzle, E

    2015-10-01

    A meta-analysis was conducted to understand quantitative aspects of calcium (Ca) and phosphorus (P) absorption in adult dogs and cats. 34 studies in dogs and 14 studies in cats met the criteria for inclusion in the meta-analysis. Intake and faecal excretion values of Ca and P were subjected to a modified Lucas test and subsequent regression analyses. According to the current scientific consensus, Ca true digestibility (absorption) should increase at low Ca intake and decrease at high Ca intake. If true, this should result in a nonlinear relationship between the percentage of Ca excreted and dietary Ca intake. The present meta-analysis showed a highly significant linear relationship (p dogs and cats at maintenance will not efficiently alter quantitative Ca absorption percentage according to the amount ingested. If the latter is true, a dietary Ca supply differing greatly from the recommended dietary intake might impair the health of cats and dogs when fed long term. The data plots for P intake and faecal excretion were less uniform suggesting other factors not just dietary intake influence faecal P excretion. In adult cats, the dietary Ca:P ratio strongly influenced the true digestibility of P, whereas this effect was less marked in adult dogs. Faecal P excretion was significantly correlated to faecal Ca excretion in both species (p < 0.0001), and surprisingly, the level of P intake did not appear to be an important determinant of true digestibility of P. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

  19. DEMONSTRATION BULLETIN: TEXACO GASIFICATION PROCESS TEXACO, INC.

    Science.gov (United States)

    The Texaco Gasification Process (TGP) has operated commercially for nearly 45 years on feeds such as natural gas, liquid petroleum fractions, coal, and petroleum coke. More than 45 plants are either operational or under development in the United States and abroad. Texaco has dev...

  20. High performance GPU processing for inversion using uniform grid searches

    Science.gov (United States)

    Venetis, Ioannis E.; Saltogianni, Vasso; Stiros, Stathis; Gallopoulos, Efstratios

    2017-04-01

    Many geophysical problems are described by systems of redundant, highly non-linear systems of ordinary equations with constant terms deriving from measurements and hence representing stochastic variables. Solution (inversion) of such problems is based on numerical, optimization methods, based on Monte Carlo sampling or on exhaustive searches in cases of two or even three "free" unknown variables. Recently the TOPological INVersion (TOPINV) algorithm, a grid search-based technique in the Rn space, has been proposed. TOPINV is not based on the minimization of a certain cost function and involves only forward computations, hence avoiding computational errors. The basic concept is to transform observation equations into inequalities on the basis of an optimization parameter k and of their standard errors, and through repeated "scans" of n-dimensional search grids for decreasing values of k to identify the optimal clusters of gridpoints which satisfy observation inequalities and by definition contain the "true" solution. Stochastic optimal solutions and their variance-covariance matrices are then computed as first and second statistical moments. Such exhaustive uniform searches produce an excessive computational load and are extremely time consuming for common computers based on a CPU. An alternative is to use a computing platform based on a GPU, which nowadays is affordable to the research community, which provides a much higher computing performance. Using the CUDA programming language to implement TOPINV allows the investigation of the attained speedup in execution time on such a high performance platform. Based on synthetic data we compared the execution time required for two typical geophysical problems, modeling magma sources and seismic faults, described with up to 18 unknown variables, on both CPU/FORTRAN and GPU/CUDA platforms. The same problems for several different sizes of search grids (up to 1012 gridpoints) and numbers of unknown variables were solved on

  1. Temperature model for process impact non-uniformity in genipin recovery by high pressure processing.

    Science.gov (United States)

    Ramos-de-la-Peña, Ana Mayela; Montañez, Julio C; Reyes-Vega, María de la Luz; Contreras-Esquivel, Juan Carlos

    2015-11-15

    A model for the process impact temperature non-uniformity during high pressure processing (HPP) of genipap fruit purees was found during genipin recovery. Purees were subjected to HPP (130-530 MPa) under quasi-isobaric non-isothermal conditions (15 min; 0, 4.6 and 9.3mg pectinases/g fruit). Genipin and protein concentration was determined, and pH was measured. Polygalacturonase activity was quantified indirectly by protein content (mg/g fruit). First order kinetics described temperature changes (0-4 min). Polygalacturonase was activated at 130 MPa, inactivated reversibly at 330 MPa and activated again at 530 MPa. Enzyme reaction rate constant (k) was placed in the 0-4 min model and temperature from 2 to 15 min was described. Protein content and pH characterization in terms of decimal reduction time improved highly the 2-15 min model. Since temperature changes were modeled, more insight of its behavior in an HPP reactor was obtained, avoiding uniformity assumptions, making easier the industrial scale HPP implementation.

  2. Apparatus and process to enhance the uniform formation of hollow glass microspheres

    Science.gov (United States)

    Schumacher, Ray F

    2013-10-01

    A process and apparatus is provided for enhancing the formation of a uniform population of hollow glass microspheres. A burner head is used which directs incoming glass particles away from the cooler perimeter of the flame cone of the gas burner and distributes the glass particles in a uniform manner throughout the more evenly heated portions of the flame zone. As a result, as the glass particles are softened and expand by a released nucleating gas so as to form a hollow glass microsphere, the resulting hollow glass microspheres have a more uniform size and property distribution as a result of experiencing a more homogenous heat treatment process.

  3. Some new almost sure results on the functional increments of the uniform empirical process

    CERN Document Server

    Varron, Davit

    2012-01-01

    Given an observation of the uniform empirical process $\\alp_n$, its functional increments $\\alp_n(u+a_n\\cdot)-\\alp_n(u)$ can be viewed as a single random process, when $u$ is distributed under the Lebesgue measure. We investigate the almost sure limit behaviour of the multivariate versions of these processes as $\

  4. Effects of process parameters on sheet resistance uniformity of fluorine-doped tin oxide thin films.

    Science.gov (United States)

    Hudaya, Chairul; Park, Ji Hun; Lee, Joong Kee

    2012-01-05

    An alternative indium-free material for transparent conducting oxides of fluorine-doped tin oxide [FTO] thin films deposited on polyethylene terephthalate [PET] was prepared by electron cyclotron resonance - metal organic chemical vapor deposition [ECR-MOCVD]. One of the essential issues regarding metal oxide film deposition is the sheet resistance uniformity of the film. Variations in process parameters, in this case, working and bubbler pressures of ECR-MOCVD, can lead to a change in resistance uniformity. Both the optical transmittance and electrical resistance uniformity of FTO film-coated PET were investigated. The result shows that sheet resistance uniformity and the transmittance of the film are affected significantly by the changes in bubbler pressure but are less influenced by the working pressure of the ECR-MOCVD system.

  5. Improving wafer level CD uniformity for logic applications utilizing mask level metrology and process

    Science.gov (United States)

    Cohen, Avi; Trautzsch, Thomas; Buttgereit, Ute; Graitzer, Erez; Hanuka, Ori

    2013-09-01

    Critical Dimension Uniformity (CDU) is one of the key parameters necessary to assure good performance and reliable functionality of any integrated circuit (IC). The extension of 193nm based lithography usage combined with design rule shrinkage makes process control, in particular the wafer level CDU control, an extremely important and challenging task in IC manufacturing. In this study the WLCD-CDC closed loop solution offered by Carl Zeiss SMS was examined. This solution aims to improve the wafer level intra-field CDU without the need to run wafer prints and extensive wafer CD metrology. It combines two stand-alone tools: The WLCD tool which measures CD based on aerial imaging technology while applying the exact scanner-used illumination conditions to the photomask and the CDC tool which utilizes an ultra-short femto-second laser to write intra-volume shading elements (Shade-In Elements™) inside the photomask bulk material. The CDC process changes the dose going through the photomask down to the wafer, hence the wafer level intra-field CDU improves. The objective of this study was to evaluate how CDC process is affecting the CD for different type of features and pattern density which are typical for logic and system on chip (SOC) devices. The main findings show that the linearity and proximity behavior is maintained by the CDC process and CDU and CDC Ratio (CDCR) show a linear behavior for the different feature types. Finally, it was demonstrated that the CDU errors of the targeted (critical) feature have been effectively eliminated. In addition, the CDU of all other features have been significantly improved as well.

  6. The Role of Demonstration Projects in Construction innovation processes

    DEFF Research Database (Denmark)

    Clausen, Lennie

    1999-01-01

    The article is describing the methodology of a case-study approach to the investigation of demonstration projects and their impact on the development of process and product innovations in the construction industry.......The article is describing the methodology of a case-study approach to the investigation of demonstration projects and their impact on the development of process and product innovations in the construction industry....

  7. Radioactive demonstration of the ``late wash`` Precipitate Hydrolysis Process

    Energy Technology Data Exchange (ETDEWEB)

    Bibler, N.E.; Ferrara, D.M.; Ha, B.C.

    1992-06-30

    This report presents results of the radioactive demonstration of the DWPF Precipitate Hydrolysis Process as it would occur in the ``late wash`` flowsheet in the absence of hydroxylamine nitrate. Radioactive precipitate containing Cs-137 from the April, 1983, in-tank precipitation demonstration in Tank 48 was used for these tests.

  8. ACTION OF UNIFORM SEARCH ALGORITHM WHEN SELECTING LANGUAGE UNITS IN THE PROCESS OF SPEECH

    Directory of Open Access Journals (Sweden)

    Nekipelova Irina Mikhaylovna

    2013-04-01

    Full Text Available The article is devoted to research of action of uniform search algorithm when selecting by human of language units for speech produce. The process is connected with a speech optimization phenomenon. This makes it possible to shorten the time of cogitation something that human want to say, and to achieve the maximum precision in thoughts expression. The algorithm of uniform search works at consciousness and subconsciousness levels. It favours the forming of automatism produce and perception of speech. Realization of human's cognitive potential in the process of communication starts up complicated mechanism of self-organization and self-regulation of language. In turn, it results in optimization of language system, servicing needs not only human's self-actualization but realization of communication in society. The method of problem-oriented search is used for researching of optimization mechanisms, which are distinctive to speech producing and stabilization of language.

  9. Effects of process parameters on sheet resistance uniformity of fluorine-doped tin oxide thin films

    OpenAIRE

    2012-01-01

    An alternative indium-free material for transparent conducting oxides of fluorine-doped tin oxide [FTO] thin films deposited on polyethylene terephthalate [PET] was prepared by electron cyclotron resonance - metal organic chemical vapor deposition [ECR-MOCVD]. One of the essential issues regarding metal oxide film deposition is the sheet resistance uniformity of the film. Variations in process parameters, in this case, working and bubbler pressures of ECR-MOCVD, can lead to a change in resist...

  10. Process monitoring in international safeguards for reprocessing plants: A demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Ehinger, M.H.

    1989-01-01

    In the period 1985--1987, the Oak Ridge National Laboratory investigated the possible role of process monitoring for international safeguards applications in fuel reprocessing plants. This activity was conducted under Task C.59, ''Review of Process Monitoring Safeguards Technology for Reprocessing Facilities'' of the US program of Technical Assistance to the International Atomic Energy Agency (IAEA) Safeguards program. The final phase was a demonstration of process monitoring applied in a prototypical reprocessing plant test facility at ORNL. This report documents the demonstration and test results. 35 figs.

  11. Improving Knowledge and Process for International Emergency Medicine Fellowship Applicants: A Call for a Uniform Application

    Directory of Open Access Journals (Sweden)

    Gabrielle A. Jacquet

    2013-01-01

    Full Text Available Background. There are currently 34 International Emergency Medicine (IEM fellowship programs. Applicants and programs are increasing in number and diversity. Without a standardized application, applicants have a difficulty approaching programs in an informed and an organized method; a streamlined application system is necessary. Objectives. To measure fellows’ knowledge of their programs’ curricula prior to starting fellowship and to determine what percent of fellows and program directors would support a universal application system. Methods. A focus group of program directors, recent, and current fellows convened to determine the most important features of an IEM fellowship application process. A survey was administered electronically to a convenience sample of 78 participants from 34 programs. Respondents included fellowship directors, fellows, and recent graduates. Results. Most fellows (70% did not know their program’s curriculum prior to starting fellowship. The majority of program directors and fellows support a uniform application service (81% and 67%, resp. and deadline (85% for both. A minority of program directors (35% and fellows (30% support a formal match. Conclusions. Program directors and fellows support a uniform application service and deadline, but not a formalized match. Forums for disseminating IEM fellowship information and for administering a uniform application service and deadline are currently in development to improve the process.

  12. Uniform lateral etching of tungsten in deep trenches utilizing reaction-limited NF3 plasma process

    Science.gov (United States)

    Kofuji, Naoyuki; Mori, Masahito; Nishida, Toshiaki

    2017-06-01

    The reaction-limited etching of tungsten (W) with NF3 plasma was performed in an attempt to achieve the uniform lateral etching of W in a deep trench, a capability required by manufacturing processes for three-dimensional NAND flash memory. Reaction-limited etching was found to be possible at high pressures without ion irradiation. An almost constant etching rate that showed no dependence on NF3 pressure was obtained. The effect of varying the wafer temperature was also examined. A higher wafer temperature reduced the threshold pressure for reaction-limited etching and also increased the etching rate in the reaction-limited region. Therefore, the control of the wafer temperature is crucial to controlling the etching amount by this method. We found that the uniform lateral etching of W was possible even in a deep trench where the F radical concentration was low.

  13. Line printing solution-processable small molecules with uniform surface profile via ink-jet printer.

    Science.gov (United States)

    Liu, Huimin; Xu, Wei; Tan, Wanyi; Zhu, Xuhui; Wang, Jian; Peng, Junbiao; Cao, Yong

    2016-03-01

    Line printing offers a feasible approach to remove the pixel well structure which is widely used to confine the ink-jet printed solution. In the study, a uniform line is printed by an ink-jet printer. To achieve a uniform surface profile of the printed line, 10vol% low-volatile solvent DMA (3,4-Dimethylanisole) is mixed with high-volatile solvent Pxy (p-xylene) as the solvent. After a solution-processable small molecule is dissolved, the surface tension of DMA solution becomes lower than that of Pxy solution, which creates an inward Marangoni flow during the solvent evaporation. The inward Marangoni flow balances out the outward capillary flow, thereby forming a flat film surface. The line width of the printed line depends on the contact angle of the solution on the hole injection layer.

  14. An effect of dummy cathode on thickness uniformity in electroforming process

    Directory of Open Access Journals (Sweden)

    Chul-Woo Park

    2014-01-01

    Full Text Available This study examines the solution for one of the most difficult problems of electroforming process “thickness deviation”. As an effective solution, an auxiliary electrode (dummy cathode is considered. Generally, the thickness of an edge plating area is almost twice the center area or greater. An auxiliary electrode (intentionally attached dummy cathode has helped to achieve more uniform thickness of the electroformed-nickel layer by preventing excessive electric charge. In addition, computer-aided analysis was performed to determine the optimal condition of electroforming process and to confirm the experimental result.

  15. Effect of spray process conditions on uniformity of carbon nanotube thin films.

    Science.gov (United States)

    Du Choi, Soon; Kim, Duckjong; Kang, Yong-Pil; Jang, Dong Hwan

    2012-07-01

    Industrial use of carbon nanotube (CNT) films is increasing rapidly due to their good physical properties and high economic feasibility. Spray coating process is one of feasible approaches for large area CNT films. Uniform spray coating is an important issue in applications requiring large area conductive films. In the present work, we developed a numerical model for the prediction of CNT deposition thickness distribution in the spray process and validated the numerical work by using experimental data obtained in this study. We investigated the deposition thickness distributions according to various process parameters by using the numerical model. We found that the pitch of the nozzle path is a key parameter affecting the deposition thickness uniformity and that there is optimal pitch value for unfirom and productive coating. We also discussed future research direction for improved numerical simulation tool. Since the present numerical model is also applicable to simulation of spray process on curvy substrate, the numerical model could be an imporatnt step toward a powerful simulation tool for design and optimization of the nanomaterial spray process.

  16. Design of demonstration facility for advanced spent fuel conditioning process

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, W. M.; Koo, J. H.; Jeo, I. J.; Kook, D. H.; Lee, E. P.; Baek, S. R.; Lee, K. I.; You, K. S.; Park, S. W. [KAERI, Taejon (Korea, Republic of)

    2003-10-01

    The Advanced spent fuel Conditioning Process(ACP) was proposed and developed for effective management of the PWR spent fuel. The detail plan was established for demonstration and verification of the ACP, and an existing hot cell will be modified as {alpha}-{gamma} type hot cell. In this study, the process mechanical flow was analysed for the optimum arrangement to ensure effective process operation in hot cell, and the detail design of hot cell including the auxiliary facility and safety analysis was performed to secure conservative safety of hot cell system. And then, this results will be utilized for hot cell refurbishment and license.

  17. A General Law of Moment Convergence Rates for Uniform Empirical Process

    Institute of Scientific and Technical Information of China (English)

    Qing Pei ZANG

    2011-01-01

    Let {Xn; n ≥ 1} be a sequence of independent and identically distributed U[0,1]-distributed random variables.Define the uniform empirical process Fn(t)=n-1/2∑ni=1(I{Xi≤t} -t),0 ≤ t ≤ 1,‖Fn‖ =sup0≤t≤1 |Fn(t)|.In this paper,the exact convergence rates of a general law of weighted infinite series of E{‖Fn‖ - εgs(n)}+ are obtained.

  18. Uniform approximation of Gaussian wavelet for biomedical signal processing in analog domain.

    Science.gov (United States)

    Makkena, Goutham; Bvvsn, Prabhakara Rao; Srinivas, M B

    2013-01-01

    Signal processing in analog domain is favorable when power consumption is a critical design constraint. Continuous Wavelet Transform (CWT), which is increasingly being used in characterizing biomedical signals, when implemented in analog domain consumes less power provided the mother wavelet is properly approximated. This paper presents an approximation of Gaussian wavelet by making use of the Uniform approximation. Simulations of the approximated wavelet and the actual wavelet in MATLAB are performed and the results discussed. Simulations show that (i) approximation obtained closely matches the mother wavelet chosen and (ii) a stable approximation which helps in physical realization using any circuit design methodology.

  19. Manufacturing Demonstration Facility: Roll-to-Roll Processing

    Energy Technology Data Exchange (ETDEWEB)

    Datskos, Panos G [ORNL; Joshi, Pooran C [ORNL; List III, Frederick Alyious [ORNL; Duty, Chad E [ORNL; Armstrong, Beth L [ORNL; Ivanov, Ilia N [ORNL; Jacobs, Christopher B [ORNL; Graham, David E [ORNL; Moon, Ji Won [ORNL

    2015-08-01

    This Manufacturing Demonstration Facility (MDF)e roll-to-roll processing effort described in this report provided an excellent opportunity to investigate a number of advanced manufacturing approaches to achieve a path for low cost devices and sensors. Critical to this effort is the ability to deposit thin films at low temperatures using nanomaterials derived from nanofermentation. The overarching goal of this project was to develop roll-to-roll manufacturing processes of thin film deposition on low-cost flexible substrates for electronics and sensor applications. This project utilized ORNL s unique Pulse Thermal Processing (PTP) technologies coupled with non-vacuum low temperature deposition techniques, ORNL s clean room facility, slot dye coating, drop casting, spin coating, screen printing and several other equipment including a Dimatix ink jet printer and a large-scale Kyocera ink jet printer. The roll-to-roll processing project had three main tasks: 1) develop and demonstrate zinc-Zn based opto-electronic sensors using low cost nanoparticulate structures manufactured in a related MDF Project using nanofermentation techniques, 2) evaluate the use of silver based conductive inks developed by project partner NovaCentrix for electronic device fabrication, and 3) demonstrate a suite of low cost printed sensors developed using non-vacuum deposition techniques which involved the integration of metal and semiconductor layers to establish a diverse sensor platform technology.

  20. PROPOSAL FOR AN UNIFORM DATA STANDARD FOR ICHNOLOGICAL 3D TRACKING AND POST-PROCESSING

    Directory of Open Access Journals (Sweden)

    MARCO PETRUZZELLI

    2011-11-01

    Full Text Available Vertebrate fossil tracks have been studied through 3D modelling techniques during the last two decades to improve tracking procedures. Different laser scanners and software have been used during field investigation and this differentiation caused incompatibility between many analysis programs. Post processing procedures are not standardized among scientists and file precision give different results in additionally constrain comparison. The starting point to find a solution to the problem is to point out the main technologies used to collect data in the field. The resulting protocol does not oblige to uniform hardware but it does suggest combining different laser scanners with a minimum post processing to optimize the result. Important inkling would be to use 2D relief as a reference to organize 3D tracking procedures. Saving formats during post processing are improved by setting fixed landmarks integrated in the 3D model in a multitask file. The D.I.C.O.M. medical standard (*.cdm format and the 3D printing international standard (*.stl format when combined, may be a good solution for uniform the format. This approach might be the first step for the standardization of source and derived files and the creation of a worldwide 3D ichnological catalogue. This will allow creating a scientific improvement in terms of reproducibility and comparison of the experience. 

  1. Processing and properties of magnesium containing a dense uniform dispersion of nanoparticles

    Science.gov (United States)

    Chen, Lian-Yi; Xu, Jia-Quan; Choi, Hongseok; Pozuelo, Marta; Ma, Xiaolong; Bhowmick, Sanjit; Yang, Jenn-Ming; Mathaudhu, Suveen; Li, Xiao-Chun

    2015-12-01

    Magnesium is a light metal, with a density two-thirds that of aluminium, is abundant on Earth and is biocompatible; it thus has the potential to improve energy efficiency and system performance in aerospace, automobile, defence, mobile electronics and biomedical applications. However, conventional synthesis and processing methods (alloying and thermomechanical processing) have reached certain limits in further improving the properties of magnesium and other metals. Ceramic particles have been introduced into metal matrices to improve the strength of the metals, but unfortunately, ceramic microparticles severely degrade the plasticity and machinability of metals, and nanoparticles, although they have the potential to improve strength while maintaining or even improving the plasticity of metals, are difficult to disperse uniformly in metal matrices. Here we show that a dense uniform dispersion of silicon carbide nanoparticles (14 per cent by volume) in magnesium can be achieved through a nanoparticle self-stabilization mechanism in molten metal. An enhancement of strength, stiffness, plasticity and high-temperature stability is simultaneously achieved, delivering a higher specific yield strength and higher specific modulus than almost all structural metals.

  2. ACTION OF UNIFORM SEARCH ALGORITHM WHEN SELECTING LANGUAGE UNITS IN THE PROCESS OF SPEECH

    Directory of Open Access Journals (Sweden)

    Ирина Михайловна Некипелова

    2013-05-01

    Full Text Available The article is devoted to research of action of uniform search algorithm when selecting by human of language units for speech produce. The process is connected with a speech optimization phenomenon. This makes it possible to shorten the time of cogitation something that human want to say, and to achieve the maximum precision in thoughts expression. The algorithm of uniform search works at consciousness  and subconsciousness levels. It favours the forming of automatism produce and perception of speech. Realization of human's cognitive potential in the process of communication starts up complicated mechanism of self-organization and self-regulation of language. In turn, it results in optimization of language system, servicing needs not only human's self-actualization but realization of communication in society. The method of problem-oriented search is used for researching of optimization mechanisms, which are distinctive to speech producing and stabilization of language.DOI: http://dx.doi.org/10.12731/2218-7405-2013-4-50

  3. Uniform Labeled Transition Systems for Nondeterministic, Probabilistic, and Stochastic Process Calculi

    CERN Document Server

    Bernardo, Marco; Loreti, Michele; 10.4204/EPTCS.60.5

    2011-01-01

    Labeled transition systems are typically used to represent the behavior of nondeterministic processes, with labeled transitions defining a one-step state to-state reachability relation. This model has been recently made more general by modifying the transition relation in such a way that it associates with any source state and transition label a reachability distribution, i.e., a function mapping each possible target state to a value of some domain that expresses the degree of one-step reachability of that target state. In this extended abstract, we show how the resulting model, called ULTraS from Uniform Labeled Transition System, can be naturally used to give semantics to a fully nondeterministic, a fully probabilistic, and a fully stochastic variant of a CSP-like process language.

  4. Differences between laminar convections through parallel plain planes with uniform wall temperature and heat flux in terms of process parameter

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Using the process parameter description,we analyzed the difference between the characteristics of laminar convections through parallel plain planes with uniform temperature and heat flux.The results show the following.(1)On the wall surface of the developing region,under uniform heat flux boundary condition,the heat flux normal to the wall surface is transported through a convection process although the velocity is zero;the velocity gradient contributes to this transport,but under uniform temperature boundary condition,the heat flux normal to the wall surface is transported through a difussion process.(2)Inside the flow of the developing region,whether under uniform temperature or heat flux boundary condition,the heat flux along the main flow direction and the heat flux normal to the wall surface are transported through a convection process,and the contributions of velocity and velocity gradient are dependent on the thermal boundary condition.(3)On the wall surface of the fully developed region,under uniform heat flux boundary condition,the heat flux normal to the wall surface is transported through a convection process;the velocity gradient contributes to this transport,but under uniform temperature boundary condition,the heat flux normal to the wall surface is transported through a diffusion process.(4)Inside the flow of the fully developed region,under uniform temperature boundary condition,the heat flux along the main flow direction and the heat flux normal to the wall surface are transported through a convection process,and the velocity and velocity gradient contribute to these transports;under uniform heat flux boundary condition,the heat flux along the main flow direction and the heat flux normal to the wall surface are transported through a convection process.Furthermore,the transport of the heat flux along the main flow direction is a no-net convection process;the velocity gradient contributes to the transport of the heat flux only in the normal direction

  5. FY 2009 Progress: Process Monitoring Technology Demonstration at PNNL

    Energy Technology Data Exchange (ETDEWEB)

    Arrigo, Leah M.; Christensen, Ronald N.; Fraga, Carlos G.; Liezers, Martin; Peper, Shane M.; Thomas, Elizabeth M.; Bryan, Samuel A.; Douglas, Matthew; Laspe, Amy R.; Lines, Amanda M.; Peterson, James M.; Ward, Rebecca M.; Casella, Amanda J.; Duckworth, Douglas C.; Levitskaia, Tatiana G.; Orton, Christopher R.; Schwantes, Jon M.

    2009-12-01

    Pacific Northwest National Laboratory (PNNL) is developing and demonstrating three technologies designed to assist in the monitoring of reprocessing facilities in near-real time. These technologies include 1) a multi-isotope process monitor (MIP), 2) a spectroscopy-based monitor that uses UV-Vis-NIR (ultraviolet-visible-near infrared) and Raman spectrometers, and 3) an electrochemically modulated separations approach (EMS). The MIP monitor uses gamma spectroscopy and pattern recognition software to identify off-normal conditions in process streams. The UV-Vis-NIR and Raman spectroscopic monitoring continuously measures chemical compositions of the process streams including actinide metal ions (uranium, plutonium, neptunium), selected fission products, and major cold flow sheet chemicals. The EMS approach provides an on-line means for separating and concentrating elements of interest out of complex matrices prior to detection via nondestructive assay by gamma spectroscopy or destructive analysis with mass spectrometry. A general overview of the technologies and ongoing demonstration results are described in this report.

  6. Process Improvement: Addressing Attrition from the Uniformed Services University of the Health Sciences Nurse Anesthesia Program.

    Science.gov (United States)

    Wilson, John Tyler; Gibbons, Susanne W; Wofford, Kenneth

    2015-10-01

    This retrospective cohort study examined the Uniformed Services University of the Health Sciences Registered Nurse Anesthesia program to identify reasons for high attrition rates. Relevant data were examined for 180 students enrolled in classes from 2005 through 2011. During that period, 40 students were dismissed or disenrolled, with the highest attrition rate (35%) occurring in the class of 2010. Evidence from this investigation indicates students who completed the program were younger, earned higher grade point averages while completing their undergraduate bachelor of science in nursing, and achieved higher analytic and total Graduate Record Examination scores than did students who withdrew or were dismissed. Gender differences were noted, as a greater proportion of women completed the program compared with men. Personal, family, and other issues frequently overlapped, with academic performance problems leading to attrition. Based on these findings, a number of important changes were made in the admission process to the USUHS RNA program and in the nonacademic mentoring and assistance offered to students.

  7. High Input Voltage, Silicon Carbide Power Processing Unit Performance Demonstration

    Science.gov (United States)

    Bozak, Karin E.; Pinero, Luis R.; Scheidegger, Robert J.; Aulisio, Michael V.; Gonzalez, Marcelo C.; Birchenough, Arthur G.

    2015-01-01

    A silicon carbide brassboard power processing unit has been developed by the NASA Glenn Research Center in Cleveland, Ohio. The power processing unit operates from two sources: a nominal 300 Volt high voltage input bus and a nominal 28 Volt low voltage input bus. The design of the power processing unit includes four low voltage, low power auxiliary supplies, and two parallel 7.5 kilowatt (kW) discharge power supplies that are capable of providing up to 15 kilowatts of total power at 300 to 500 Volts (V) to the thruster. Additionally, the unit contains a housekeeping supply, high voltage input filter, low voltage input filter, and master control board, such that the complete brassboard unit is capable of operating a 12.5 kilowatt Hall effect thruster. The performance of the unit was characterized under both ambient and thermal vacuum test conditions, and the results demonstrate exceptional performance with full power efficiencies exceeding 97%. The unit was also tested with a 12.5kW Hall effect thruster to verify compatibility and output filter specifications. With space-qualified silicon carbide or similar high voltage, high efficiency power devices, this would provide a design solution to address the need for high power electric propulsion systems.

  8. Process makes product: Demonstration green building at Canadian university

    Energy Technology Data Exchange (ETDEWEB)

    Marques, J.; Pagani, F.; Perdue, J.

    1999-07-01

    In 1992 while in the midst of a C$500 million, ten-year capital expansion program, a Canadian university made a commitment to develop a demonstration green building. The building, which had been budgeted and scheduled prior to this commitment, is a 2,700 m{sup 2} (29,000 ft{sup 2}) office and seminar building, which was designed and constructed without any adjustments to the original budget or to the schedule due to green initiatives. At the outset of the project, the university convened a workshop with the consultants, subconsultants, users, and building operators to develop by consensus a set of targets for site ecology, energy use, water use, material reduction, and waste reduction. The building has met or exceeded the majority of the targets and is being monitored on an ongoing basis. Some of the specific achievements of the project team are a 69% reduction in electricity use from ASHRAE 90.1; a lighting intensity of 9 W/m{sup 2} (0.9 W/ft{sup 2}); on-site wastewater treatment through composting toilets and a constructed wetland for grey water; approximately 50% reused, recycled, and recyclable materials, natural stack ventilation supplemented by fans in temperature extremes; workstations next to operable windows with maximum access to natural light; a construction waste management plan to reduce waste from the site. Process innovations included the commitment from the owner, the establishment of targets by the entire project team, and the inclusion of the subconsultants in the design process from the beginning.

  9. Processing and properties of pressable ceramic with non-uniform reinforcement for selective-toughening

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Wei [School of Mechanical and Chemical Engineering, The University of Western Australia, Perth, WA 6009 (Australia); School of Dentistry, The University of Western Australia, WA 6009 (Australia); Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Shenyang 110004 (China); Hu, Xiaozhi, E-mail: xiao.zhi.hu@uwa.edu.au [School of Mechanical and Chemical Engineering, The University of Western Australia, Perth, WA 6009 (Australia); Ichim, Paul [School of Dentistry, The University of Western Australia, WA 6009 (Australia); Sun, Xudong [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Shenyang 110004 (China)

    2012-12-15

    Brittle low-strength and low-toughness pressable dental ceramic can be reinforced by ductile elongated gold-particles (GP). A customized crown structure can be adequately strengthened by distributing GP only in critical sections of the crown, where high tensile stresses are experienced. In the present study, a non-uniformly structured ceramic-matrix composite with excellent interfacial bonding, twofold fracture toughness and strength at desired locations, is fabricated using pressable dental ceramic and GP. The layout pattern and sequence of different GP/ceramic powder mixtures, high-temperature flow properties of these mixtures during hot-pressing and the sample mold geometry are used to control the distribution and locations of GP for selective toughening and strengthening. Nano-crystalline structures of the pressable ceramic-matrix and the nano-scaled interfacial region around GP have been revealed by high-magnification field-emission scanning electron microscopy. Toughening and strengthening mechanisms of the elongated GP including residual stresses from composite processing and ductile fracture of GP are discussed together with SEM observations. Bulk flexural strength and local micro-indentation fracture and deformation characteristics of the selective-toughened ceramic/metal composite have been compared to those of the monolithic pressable ceramic to validate the toughening and strengthening mechanisms.

  10. Engineering scale demonstration of a prospective Cast Stone process

    Energy Technology Data Exchange (ETDEWEB)

    Cozzi, A.; Fowley, M.; Hansen, E.; Fox, K.; Miller, D.; Williams, M.

    2014-09-30

    This report documents an engineering-scale demonstration with non-radioactive simulants that was performed at SRNL using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. Over three days, the SCPF was used to fill a 1600 gallon container, staged outside the facility, with simulated Cast Stone grout. The container, staged outside the building approximately 60 ft from the SCPF, was instrumented with x-, y-, and z-axis thermocouples to monitor curing temperature. The container was also fitted with two formed core sampling vials. For the operation, the targeted grout production rate was 1.5 gpm. This required a salt solution flow rate of approximately 1 gpm and a premix feed rate of approximately 580 lb/h. During the final day of operation, the dry feed rate was increased to evaluate the ability of the system to handle increased throughput. Although non-steady state operational periods created free surface liquids, no bleed water was observed either before or after operations. The final surface slope at a fill height of 39.5 inches was 1-1.5 inches across the 8.5 foot diameter container, highest at the final fill point and lowest diametrically opposed to the fill point. During processing, grout was collected in cylindrical containers from both the mixer discharge and the discharge into the container. These samples were stored in a humid environment either in a closed box proximal to the container or inside the laboratory. Additional samples collected at these sampling points

  11. Modelling of human low frequency sound localization acuity demonstrates dominance of spatial variation of interaural time difference and suggests uniform just-noticeable differences in interaural time difference.

    Directory of Open Access Journals (Sweden)

    Rosanna C G Smith

    Full Text Available Sound source localization is critical to animal survival and for identification of auditory objects. We investigated the acuity with which humans localize low frequency, pure tone sounds using timing differences between the ears. These small differences in time, known as interaural time differences or ITDs, are identified in a manner that allows localization acuity of around 1° at the midline. Acuity, a relative measure of localization ability, displays a non-linear variation as sound sources are positioned more laterally. All species studied localize sounds best at the midline and progressively worse as the sound is located out towards the side. To understand why sound localization displays this variation with azimuthal angle, we took a first-principles, systemic, analytical approach to model localization acuity. We calculated how ITDs vary with sound frequency, head size and sound source location for humans. This allowed us to model ITD variation for previously published experimental acuity data and determine the distribution of just-noticeable differences in ITD. Our results suggest that the best-fit model is one whereby just-noticeable differences in ITDs are identified with uniform or close to uniform sensitivity across the physiological range. We discuss how our results have several implications for neural ITD processing in different species as well as development of the auditory system.

  12. Ishikawa iteration process with errors for nonexpansive mappings in uniformly convex Banach spaces

    OpenAIRE

    Deng Lei; Li Shenghong

    2000-01-01

    We shall consider the behaviour of Ishikawa iteration with errors in a uniformly convex Banach space. Then we generalize the two theorems of Tan and Xu without the restrictions that C is bounded and limsupnsn

  13. The influence of printing substrate on macro non-uniformity and line reproduction quality of imprints printed with electrophotographic process

    Directory of Open Access Journals (Sweden)

    Đorđe Vujčić

    2016-12-01

    Full Text Available Print quality is very important for every printing technique. It depends on many different quality attributes. This research included analysis of macro non-uniformities and line reproduction. 16 different paper substrates printed by electrophotographic process were analyzed. They were separated in two groups: coated and uncoated papers. Analysis of macro non-uniformity showed that print mottle has lower values when printed on coated papers than on uncoated papers. Line reproduction analysis showed that the toner spreaded, during melting and fixation, on line edges for both types of paper. According to these results it can be concluded that paper substrate affects the macro non-uniformity and line reproduction, thus overall print quality.

  14. Effects of Process Parameters on Deformation and Temperature Uniformity of Forged Ti-6Al-4V Turbine Blade

    Science.gov (United States)

    Luo, Shiyuan; Zhu, Dahu; Hua, Lin; Qian, Dongsheng; Yan, Sijie; Yu, Fengping

    2016-11-01

    This work is motivated by the frequent occurrence of macro- and microdefects within forged Ti-6Al-4V turbine blades due to the severely nonuniform strain and temperature distributions. To overcome the problem of nonuniformity during the blade forging operation, firstly, a 2D coupled thermo-mechanical finite element approach using the strain-compensated Arrhenius-type constitutive model is employed to simulate the real movements and processing conditions, and its reliability is verified experimentally. Secondly, two evaluation indexes, standard deviation of equivalent plastic strain and standard deviation of temperature, are proposed to evaluate the uniformity characteristics within the forged blade, and the effects of four process parameters including the forging velocity, friction factor, initial workpiece temperature and dwell time on the uniformity of strain and temperature distributions are carefully studied. Finally, the numerically optimized combination of process parameters is validated by the application in a practical process. The parametric study reveals that a reasonable combination of process parameters considering the flow resistance, flow localization and the effects of deformation and friction heating is crucial for the titanium alloy blade forging with uniformity. This work can provide a significant guidance for the design and optimization of blade forging processes.

  15. Effect of gold wire bonding process on angular correlated color temperature uniformity of white light-emitting diode.

    Science.gov (United States)

    Wu, Bulong; Luo, Xiaobing; Zheng, Huai; Liu, Sheng

    2011-11-21

    Gold wire bonding is an important packaging process of lighting emitting diode (LED). In this work, we studied the effect of gold wire bonding on the angular uniformity of correlated color temperature (CCT) in white LEDs whose phosphor layers were coated by freely dispersed coating process. Experimental study indicated that different gold wire bonding impacts the geometry of phosphor layer, and it results in different fluctuation trends of angular CCT at different spatial planes in one LED sample. It also results in various fluctuating amplitudes of angular CCT distributions at the same spatial plane for samples with different wire bonding angles. The gold wire bonding process has important impact on angular uniformity of CCT in LED package.

  16. On the uniform convergence of random series in Skorohod space and representations of cadlag infinitely divisible processes

    CERN Document Server

    Basse-O'Connor, Andreas

    2011-01-01

    Let $X_n$ be independent random elements in the Skorohod space $D([0,1]; E)$ of cadlag functions taking values in a separable Banach space $E$. Let $S_n = \\sum_{j=1}^{n} X_j$. We show that if $S_n$ converges in finite dimensional distributions to a cadlag process, then $S_n + y_n$ converges a.s. pathwise uniformly over $[0,1]$, for some $y_n \\in D([0,1]; E)$. This result extends the Ito-Nisio Theorem to the space $D([0,1]; E)$, which is surprisingly lacking in the literature even for $E=\\R$. The main difficulties of dealing with $D([0,1]; E)$ in this context are its non-separability under the uniform norm and the discontinuity of the addition under Skorohod's $J_1$-topology. We use this result to prove the uniform convergence of various series representations of cadlag infinitely divisible processes. As a consequence, we obtain explicit representations of the jump process, and of related path functionals, in a general non-Markovian setting. Finally, we illustrate our results on an example of stable processes....

  17. Uniformity and continuity of effective strain in AZ91D processed by multi-pass equal channel angular extrusion

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xiao-hua; LUO Shou-jing; DU Zhi-ming

    2008-01-01

    AZ91D magnesium alloy was processed by equal channel angular extrusion(ECAE). The influence of extrusion temperature, extrusion pass and extrusion route on the ultimate strength of the extruded billet was analyzed. The process of multi-pass extrusion was simulated with the method of finite element analysis, and the continuity and uniformity of effective strain in multi-pass extrusion were investigated. The results show that extrusion pass plays the most important role in improving the ultimate strength of AZ91D magnesium alloy, the extrusion route is the second, and the extrusion temperature is the last. From the numerical simulation, there exists the continuity of the accumulated deformation in multi-pass extrusion and the effective strain increases linearly. The tendency of the strain uniformity is different in multi-pass extrusion with extrusion routes. The results of experiment agree with those of numerical simulation.

  18. Semantic processing in connected speech at a uniformly early stage of autopsy-confirmed Alzheimer's disease.

    Science.gov (United States)

    Ahmed, Samrah; de Jager, Celeste A; Haigh, Anne-Marie; Garrard, Peter

    2013-01-01

    The aim of the present study was to quantify the semantic content of connected speech produced by patients at a uniformly early stage of pathologically proven Alzheimer's disease (AD). A secondary aim was to establish whether semantic units were reduced globally, or whether there was a disproportionate reduction of specific classes of information. Discourse samples were obtained from 18 AD patients and 18 matched controls, all pathologically confirmed. Semantic unit identification was scored overall and for four subclasses: subjects, locations, objects, and actions. Idea density and efficiency were calculated. AD transcripts showed significantly reduced units overall, particularly actions and subjects, as well as reduced efficiency. Total semantic units and a combination of subject-, location-, and object-related units ("noun" units) correlated with the Expression subscore on the Cambridge Cognitive Examination (CAMCOG). Subject related units correlated with the CAMCOG Abstract Thinking scale. Logistic regression analyses confirmed that all measures that were lower in AD than controls were predictive of group membership. An exploratory comparison between units expressed mainly using nouns and those mainly using verbs showed that the latter was the stronger of these two predictors. The present study adds a lexico-semantic dimension to the linguistic profile based on discourse analysis in typical AD, recently described by the same authors. 2012, 83(11): 1056-1062). The suggestion of differential importance of verb and noun use in the present study may be related to the reduction in syntactic complexity that was reported, using the same set of discourse samples, in the earlier study.

  19. Uniform presentation of process evaluation results facilitates the evaluation of complex interventions: development of a graph

    NARCIS (Netherlands)

    Bakker, F.C.; Persoon, A.; Schoon, Y.; Olde Rikkert, M.G.M.

    2015-01-01

    RATIONALE, AIMS AND OBJECTIVES: Process evaluation is a highly essential element for the increasing number of studies regarding multi-component interventions. Yet, researchers are challenged to collect and present appropriate process outcomes in such way that it is easy and valuable to be used by ot

  20. The effect of stirring in the hydrothermal process to convert the mixed municipal solid waste into uniform solid fuel

    Science.gov (United States)

    Prawisudha, P.; Mu'min, G. F.; Yoshikawa, K.; Pasek, A. D.

    2016-06-01

    An innovative waste treatment technology has been developed in Indonesia to treat the mixed municipal solid waste into a solid fuel by employing the hydrothermal process. A mixture of organic and plastic waste was treated in a 2.5 L reactor using saturated steam in the temperature range of 120 to 180 °C. Two modes of operation were employed to achieve two different goals, i.e. without stirring (NS mode) and with stirring (WS mode). It was observed that both modes resulted in increasing density of product up to twofold of the raw MSW. In NS mode, the processed mixed MSW was converted into two different products; however, in WS mode the bulky plastic was converted into small granules, producing a uniform product. The results suggest that by hydrothermal treatment, the organic fibers in the organic parts are trapped into the plastic, and the stirring breaks the bulky plastics, producing uniform granules suitable as solid fuel. Therefore, the stirring during the hydrothermal process can be a solution to treat the MSW as it is, without any separation, to produce a clean and renewable energy source.

  1. Development and demonstration of manufacturing processes for fabricating graphite/LARC 160 polyimide structural elements

    Science.gov (United States)

    Frost, R. K.; Jones, J. S.; Dynes, P. J.; Wykes, D. H.

    1981-01-01

    The development and demonstration of manufacturing technologies for the structural application of Celion graphite/LARC-160 polyimide composite material is discussed. Process development and fabrication of demonstration components are discussed. Process development included establishing quality assurance of the basic composite material and processing, nondestructive inspection of fabricated components, developing processes for specific structural forms, and qualification of processes through mechanical testing. Demonstration components were fabricated. The demonstration components consisted of flat laminates, skin/stringer panels, honeycomb panels, chopped fiber compression moldings, and a technology demonstrator segment (TDS) representative of the space shuttle aft body flap.

  2. Influence of formulation composition and processing on the content uniformity of low-dose tablets manufactured at kilogram scale.

    Science.gov (United States)

    Morris, Daniel G; Truitt, Brett F; Kong, Angela; Leyva, Norma; Luner, Paul E

    2009-01-01

    The purpose of this study was to investigate the impact of processing, API loading, and formulation composition on the content uniformity of low-dose tablets made using direct compression (DC) and roller compaction (RC) methods at 1 kg scale. Blends of 1:1 microcrystalline cellulose/lactose or 1:1 microcrystalline cellulose/dicalcium phosphate anhydrous with active pharmaceutical ingredient (API) at loadings of 0.2, 1 and 5% were processed either by DC or RC. A statistical analysis showed that DC produced comparable content uniformity results to RC. Microcrystalline cellulose/lactose formulations had improved average potency compared to microcrystalline cellulose/dicalcium phosphate anhydrous formulations for both DC and RC. The impact of segregation in the DC blends and adhesion to equipment surfaces was assessed to aid in understanding potency trends. DC may be as suitable as RC for low-dose regime (e.g. < 1 mg) when manufacturing clinical supplies at small scale provided the API has a suitable particle size and potency loss to equipment is negligible.

  3. Efficient computation of time-bounded reachability probabilities in uniform continuous-time Markov decision processes

    NARCIS (Netherlands)

    Baier, Christel; Hermanns, H.; Katoen, Joost P.; Haverkort, Boudewijn R.H.M.

    2005-01-01

    A continuous-time Markov decision process (CTMDP) is a generalization of a continuous-time Markov chain in which both probabilistic and nondeterministic choices co-exist. This paper presents an efficient algorithm to compute the maximum (or minimum) probability to reach a set of goal states within a

  4. A Process Analysis of the Uniform Chart of Accounts Personnel Utilization System

    Science.gov (United States)

    2002-04-23

    Graduate Dental Education Gen Residency Program Periodontics Residency Endodontics Residency Prosthodontics Residency Oral...cost-accounting systems. American Journal of Hospital Pharmacy; 45, 1103-10. Dean, E.B. (1996). Business Process Reengineering. Retrieved from the...UCAPERS 53 Hughes, M. (1999). Nursing workload: an unquantifiable entity. Journal of Nursing Management, 7, 17-22

  5. Facile microwave synthesis of uniform magnetic nanoparticles with minimal sample processing

    Science.gov (United States)

    Schneider, Thomas; Löwa, Anna; Karagiozov, Stoyan; Sprenger, Lisa; Gutiérrez, Lucía; Esposito, Tullio; Marten, Gernot; Saatchi, Katayoun; Häfeli, Urs O.

    2017-01-01

    We present a simple and rapid method for the synthesis of small magnetic nanoparticles (diameters in the order of 5-20 nm) and narrow size distributions (CV's of 20-40%). The magnetite nanoparticles were synthesized in green solvents within minutes and the saturation magnetization of the particles was tunable by changes in the reaction conditions. We show that this particle synthesis method requires minimal processing steps and we present the successful coating of the particles with reactive bisphosphonates after synthesis without washing or centrifugation. We found minimal batch-to-batch variability and show the scalability of the particle synthesis method. We present a full characterization of the particle properties and believe that this synthesis method holds great promise for facile and rapid generation of magnetic nanoparticles with defined surface coatings for magnetic targeting applications.

  6. UNIFORM TiO2 NANOPARTICLES SYNTHESIS AND CHARACTERIZATION BY THERMOLYSIS PROCESS

    Directory of Open Access Journals (Sweden)

    DEBASHREE BHAKAT

    2012-07-01

    Full Text Available In this communication we present a versatile technique to synthesis spherical TiO2 nanoparticles by thermolysis process. Nanometer-sized Titania particles have been prepared by chemical reactions between Titanium tetrachloride and double distilled water in presence of hydrochloric acid. The size of the particles formed varied in the range of 100 to 300 nm and the morphology of the nanoparticles is spherical in shape having nanorods like structure on the surface of nanoparticles. The shape, size and structure of titanium dioxide products depends on the heating time and the quantity of titanium tetrachloride used in the reaction the powders were analyzed byUV-VIS spectroscopy and X-ray diffraction (XRD and Scanning electron microscopy observation was used for agglomerate observations. In the present research work, the important synthesis issues and applications of these nanoparticles are discussed in detail.

  7. A uniform analysis of HD209458b Spitzer/IRAC lightcurves with Gaussian process models

    CERN Document Server

    Evans, Thomas M; Gibson, Neale; Barstow, Joanna K; Amundsen, David S; Tremblin, Pascal; Mourier, Pierre

    2015-01-01

    We present an analysis of Spitzer/IRAC primary transit and secondary eclipse lightcurves measured for HD209458b, using Gaussian process models to marginalise over the intrapixel sensitivity variations in the 3.6 micron and 4.5 micron channels and the ramp effect in the 5.8 micron and 8.0 micron channels. The main advantage of this approach is that we can account for a broad range of degeneracies between the planet signal and systematics without actually having to specify a deterministic functional form for the latter. Our results do not confirm a previous claim of water absorption in transmission. Instead, our results are more consistent with a featureless transmission spectrum, possibly due to a cloud deck obscuring molecular absorption bands. For the emission data, our values are not consistent with the thermal inversion in the dayside atmosphere that was originally inferred from these data. Instead, we agree with another re-analysis of these same data, which concluded a non-inverted atmosphere provides a b...

  8. Image processing techniques for measuring non-uniform film thickness profiles

    Energy Technology Data Exchange (ETDEWEB)

    Nitta, S.V.; Liu, An-Hong; Plawsky, J.L.; Wayner, P.C. Jr. [Rensselaer Polytechnique Institute, Troy, NY (United States)

    1996-12-31

    The long term objective of this research program is to determine the fluid flow and drying characteristics of thin liquid/solid films using image processing techniques such as Image Analyzing Interferometry (IAI) and Image Scanning Ellipsometry (ISE). The primary purpose of this paper is to present experimental data on the effectiveness of IAI and ISE to measure nonuniform film thickness profiles. Steady-state, non-isothermal profiles of evaporating films were measured using IAI. Transient thickness profiles of a draining film were measured using ISE. The two techniques are then compared and contrasted. The ISE can be used to measure transient as well as steady-state profiles of films with thickness ranging from 1 nm to > 20 {mu}m, whereas IAI can be used to directly measure Steady-state and transient profiles of only films thicker than about 100 nm. An evaluation of the reflected intensity can be used to extend the use of the IAI below 100 nm.

  9. Multidimensional upwind hydrodynamics on unstructured meshes using graphics processing units - I. Two-dimensional uniform meshes

    Science.gov (United States)

    Paardekooper, S.-J.

    2017-08-01

    We present a new method for numerical hydrodynamics which uses a multidimensional generalization of the Roe solver and operates on an unstructured triangular mesh. The main advantage over traditional methods based on Riemann solvers, which commonly use one-dimensional flux estimates as building blocks for a multidimensional integration, is its inherently multidimensional nature, and as a consequence its ability to recognize multidimensional stationary states that are not hydrostatic. A second novelty is the focus on graphics processing units (GPUs). By tailoring the algorithms specifically to GPUs, we are able to get speedups of 100-250 compared to a desktop machine. We compare the multidimensional upwind scheme to a traditional, dimensionally split implementation of the Roe solver on several test problems, and we find that the new method significantly outperforms the Roe solver in almost all cases. This comes with increased computational costs per time-step, which makes the new method approximately a factor of 2 slower than a dimensionally split scheme acting on a structured grid.

  10. The Computer-Aided Analytic Process Model. Operations Handbook for the Analytic Process Model Demonstration Package

    Science.gov (United States)

    1986-01-01

    Research Note 86-06 THE COMPUTER-AIDED ANALYTIC PROCESS MODEL : OPERATIONS HANDBOOK FOR THE ANALYTIC PROCESS MODEL DE ONSTRATION PACKAGE Ronald G...ic Process Model ; Operations Handbook; Tutorial; Apple; Systems Taxonomy Mod--l; Training System; Bradl1ey infantry Fighting * Vehicle; BIFV...8217. . . . . . . .. . . . . . . . . . . . . . . . * - ~ . - - * m- .. . . . . . . item 20. Abstract -continued companion volume-- "The Analytic Process Model for

  11. Comminution process to produce wood particles of uniform size and shape with disrupted grain structure from veneer

    Science.gov (United States)

    Dooley, James H.; Lanning, David N.

    2017-03-28

    Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of wood veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) aligned normal to W and L, wherein the W.times.H dimensions define a pair of substantially parallel end surfaces with end checking between crosscut fibers.

  12. An investigation into the cumulative breakdown process of polymethylmethacrylate in quasi-uniform electric field under nanosecond pulses

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Liang; Cang Su, Jian; Bo Zhang, Xi; Feng Pan, Ya; Min Wang, Li; Peng Fang, Jin; Sun, Xu; Lui, Rui [Science and Technology on High Power Microwave Laboratory, Northwest Institute of Nuclear Technology, P.O. Box 69 Branch 13, Xi' an 710024 (China)

    2013-08-15

    A group of complete images on the discharge channel developed in PMMA in quasi-uniform electric field under nanosecond pulses are observed with an on-line transmission microscope. The characteristics of the cumulative breakdown process are also generalized, which include initiating from the vicinity of the cathode, developing to the anode with a branch-like shape, and taking on a wormhole appearance when final breakdown occurs. The concluded characteristics are explained by referring to the conceptions of “low density domain” and “free radical” and considering the initial discharge channel as a virtual needle. The characteristics are helpful for designers to enhance the lifetime of insulators employed on a nanosecond time scale.

  13. Comminution process to produce wood particles of uniform size and shape with disrupted grain structure from veneer

    Energy Technology Data Exchange (ETDEWEB)

    Dooley, James H.; Lanning, David N.

    2017-03-28

    Comminution process of wood veneer to produce wood particles, by feeding wood veneer in a direction of travel substantially normal to grain through a counter rotating pair of intermeshing arrays of cutting discs arrayed axially perpendicular to the direction of wood veneer travel, wherein the cutting discs have a uniform thickness (Td), to produce wood particles characterized by a length dimension (L) substantially equal to the Td and aligned substantially parallel to grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) aligned normal to W and L, wherein the W.times.H dimensions define a pair of substantially parallel end surfaces with end checking between crosscut fibers.

  14. EPA SITE DEMONSTRATION OF THE INTERNATIONAL WASTE TECHNOLOGIES/GEO-CON IN SITU STABILIZATION/ SOLIDIFICATION PROCESS

    Science.gov (United States)

    This paper presents an EPA evaluation of the first field demonstration of an in situ stabilization/solidification process for contaminated soil under the EPA Superfund Innovative Technology Evaluation (SITE) program. Demonstration of this process was a joint effort of two vendors...

  15. Understanding geodesy and geoscience processes through interactive demonstrations for the general public

    Science.gov (United States)

    Olds, S. E.; Bartel, B. A.

    2016-12-01

    Hands-on demonstrations are an effective way for novice learners, whether they are students, public, or museum visitors, to experience geoscience processes. UNAVCO and community members have developed hands-on demonstrations of a variety of geophysical processes highlighting the geodetic techniques used to measure these processes. These demonstrations illustrate how observations of changes at the earth's surface can be quantified and inform us about forces within the earth that we can't see. They also emphasize the societal impact of research related to each earth process. In this presentation, we will provide descriptions of a suite of these demonstrations, major concepts covered, materials needed, instructions for assembly and how to lead the demonstration, sample questions to ask participants, weaknesses inherent in the model, and a list of supporting handouts that augment the demonstration. Some of the demonstrations to be highlighted include: volcanic deformation using flour or an augmented-reality sandbox; isostatic rebound from glacial melt using flubber; compression of the Pacific Northwest using springs; and tsunami early warning using a tub of water and foam buoys. We will also discuss the process of developing interactive demonstrations and provide initial feedback from classroom and science festival events. Write-ups of the demonstrations are freely available on the UNAVCO Education website (search terms: UNAVCO geodetic demonstrations).

  16. Uniform polyhedra

    CERN Document Server

    Melikhov, Sergey A

    2011-01-01

    Although topological and uniform approaches to foundations of what was then known as Analysis Situs originated in the same works by M. Frechet and F. Riesz, uniform spaces hopelessly lagged behind in development, and were never taken seriously in algebraic and geometric topology, due in part to the lack of a coherent theory of quotient spaces, and of a reasonable notion of a polyhedron in the uniform category. Yet there are painful side effects of the usual topological foundations: for instance, the non-metrizability of the cone over the real line, and the non-metrizability of RP^\\infty (as a CW-complex or as the geometric realization of a simplicial set). We show that (the topology of) quotient uniformity is, after all, far nicer than quotient topology in the context of metrizable spaces, and that (metrizable, possibly locally infinite-dimensional) uniform polyhedra do exist - and behave nicely - which appears to provide a satisfactory solution to an old open-ended problem by Isbell.

  17. Additive Manufacturing of 17-4 PH Stainless Steel: Post-processing Heat Treatment to Achieve Uniform Reproducible Microstructure

    Science.gov (United States)

    Cheruvathur, Sudha; Lass, Eric A.; Campbell, Carelyn E.

    2016-03-01

    17-4 precipitation hardenable (PH) stainless steel is a useful material when a combination of high strength and good corrosion resistance up to about 315°C is required. In the wrought form, this steel has a fully martensitic structure that can be strengthened by precipitation of fine Cu-rich face-centered cubic phase upon aging. When fabricated via additive manufacturing (AM), specifically laser powder-bed fusion, 17-4 PH steel exhibits a dendritic structure containing a substantial fraction of nearly 50% of retained austenite along with body centered cubic/martensite and fine niobium carbides preferentially aligned along interdendritic boundaries. The effect of post-build thermal processing on the material microstructure is studied in comparison to that of conventionally produced wrought 17-4 PH with the intention of creating a more uniform, fully martensitic microstructure. The recommended stress relief heat treatment currently employed in industry for post-processing of AM 17-4 PH steel is found to have little effect on the as-built dendritic microstructure. It is found that, by implementing the recommended homogenization heat treatment regimen of Aerospace Materials Specification 5355 for CB7Cu-1, a casting alloy analog to 17-4 PH, the dendritic solidification structure is eliminated, resulting in a microstructure containing about 90% martensite with 10% retained austenite.

  18. Influence of Process Parameters on Content Uniformity of a Low Dose Active Pharmaceutical Ingredient in a Tablet Formulation According to GMP

    Directory of Open Access Journals (Sweden)

    Muselík Jan

    2014-09-01

    Full Text Available The article describes the development and production of tablets using direct compression of powder mixtures. The aim was to describe the impact of filler particle size and the time of lubricant addition during mixing on content uniformity according to the Good Manufacturing Practice (GMP process validation requirements. Processes are regulated by complex directives, forcing the producers to validate, using sophisticated methods, the content uniformity of intermediates as well as final products. Cutting down of production time and material, shortening of analyses, and fast and reliable statistic evaluation of results can reduce the final price without affecting product quality. The manufacturing process of directly compressed tablets containing the low dose active pharmaceutical ingredient (API warfarin, with content uniformity passing validation criteria, is used as a model example. Statistic methods have proved that the manufacturing process is reproducible. Methods suitable for elucidation of various properties of the final blend, e.g., measurement of electrostatic charge by Faraday pail and evaluation of mutual influences of researched variables by partial least square (PLS regression, were used. Using these methods, it was proved that the filler with higher particle size increased the content uniformity of both blends and the ensuing tablets. Addition of the lubricant, magnesium stearate, during the blending process improved the content uniformity of blends containing the filler with larger particles. This seems to be caused by reduced sampling error due to the suppression of electrostatic charge.

  19. Radioactive demonstration of the late wash'' Precipitate Hydrolysis Process

    Energy Technology Data Exchange (ETDEWEB)

    Bibler, N.E.; Ferrara, D.M.; Ha, B.C.

    1992-06-30

    This report presents results of the radioactive demonstration of the DWPF Precipitate Hydrolysis Process as it would occur in the late wash'' flowsheet in the absence of hydroxylamine nitrate. Radioactive precipitate containing Cs-137 from the April, 1983, in-tank precipitation demonstration in Tank 48 was used for these tests.

  20. DEVELOPMENT AND DEMONSTRATION OF POLYMER MICROENCAPSULATION OF MIXED WASTE USING KINETIC MIXER PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    LAGERAAEN,P.R.; KALB,P.D.; MILIAN,L.W.; ADAMS,J.W.

    1997-11-01

    Thermokinetic mixing was investigated as an alternative processing method for polyethylene microencapsulation, a technology well demonstrated for treatment of hazardous, low-level radioactive and low-level mixed wastes. Polyethylene encapsulation by extrusion has been previously shown to be applicable to a wide range of waste types but often pretreatment of the wastes is necessary due to process limitations regarding the maximum waste moisture content and particle size distribution. Development testing was conducted with kinetic mixing in order to demonstrate technology viability and show improved process applicability in these areas. Testing to establish process capabilities and relevant operating parameters was performed with waste surrogates including an aqueous evaporator concentrate and soil. Using a pilot-scale kinetic mixer which was installed and modified for this program, the maximum waste moisture content and particle size was determined. Following process development with surrogate wastes, the technology was successfully demonstrated at BNL using actual mixed waste.

  1. Stretching the limits of forming processes by robust optimization: A demonstrator

    NARCIS (Netherlands)

    Wiebenga, J.H.; Atzema, E.H.; Atzema, E.H.; van den Boogaard, Antonius H.; Yoon, Jeong Whan; Stoughton, Thomas B.; Rolfe, Bernard; Beynon, John H.; Hodgson, Peter

    2014-01-01

    Robust design of forming processes using numerical simulations is gaining attention throughout the industry. In this work, it is demonstrated how robust optimization can assist in further stretching the limits of metal forming processes. A deterministic and a robust optimization study are performed,

  2. Reliable solution processed planar perovskite hybrid solar cells with large-area uniformity by chloroform soaking and spin rinsing induced surface precipitation

    Directory of Open Access Journals (Sweden)

    Yann-Cherng Chern

    2015-08-01

    Full Text Available A solvent soaking and rinsing method, in which the solvent was allowed to soak all over the surface followed by a spinning for solvent draining, was found to produce perovskite layers with high uniformity on a centimeter scale and with much improved reliability. Besides the enhanced crystallinity and surface morphology due to the rinsing induced surface precipitation that constrains the grain growth underneath in the precursor films, large-area uniformity with film thickness determined exclusively by the rotational speed of rinsing spinning for solvent draining was observed. With chloroform as rinsing solvent, highly uniform and mirror-like perovskite layers of area as large as 8 cm × 8 cm were produced and highly uniform planar perovskite solar cells with power conversion efficiency of 10.6 ± 0.2% as well as much prolonged lifetime were obtained. The high uniformity and reliability observed with this solvent soaking and rinsing method were ascribed to the low viscosity of chloroform as well as its feasibility of mixing with the solvent used in the precursor solution. Moreover, since the surface precipitation forms before the solvent draining, this solvent soaking and rinsing method may be adapted to spinless process and be compatible with large-area and continuous production. With the large-area uniformity and reliability for the resultant perovskite layers, this chloroform soaking and rinsing approach may thus be promising for the mass production and commercialization of large-area perovskite solar cells.

  3. The Computer-Aided Analytic Process Model. Operations Handbook for the APM (Analytic Process Model) Demonstration Package. Appendix

    Science.gov (United States)

    1986-01-01

    The Analytic Process Model for System Design and Measurement: A Computer-Aided Tool for Analyzing Training Systems and Other Human-Machine Systems. A...separate companion volume--The Computer-Aided Analytic Process Model : Operations Handbook for the APM Demonstration Package is also available under

  4. Advanced Coal Conversion Process Demonstration Project. Technical progress report, January 1, 1993--December 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-02-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from January 1, 1993, through December 31, 1993. This project demonstrates an advanced, thermal, coal drying process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low- rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal{reg_sign} process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal processing, the coal is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal. Rosebud SynCoal Partnership`s ACCP Demonstration Facility entered Phase III, Demonstration Operation, in April 1992 and operated in an extended startup mode through August 10, 1993, when the facility became commercial. Rosebud SynCoal Partnership instituted an aggressive program to overcome startup obstacles and now focuses on supplying product coal to customers. Significant accomplishments in the history of the SynCoal{reg_sign} process development are shown in Appendix A.

  5. Laboratory Demonstration of the Pretreatment Process with Caustic and Oxidative Leaching Using Actual Hanford Tank Waste

    Energy Technology Data Exchange (ETDEWEB)

    Fiskum, Sandra K.; Billing, Justin M.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Snow, Lanee A.

    2009-01-01

    This report describes the bench-scale pretreatment processing of actual tank waste materials through the entire baseline WTP pretreatment flowsheet in an effort to demonstrate the efficacy of the defined leaching processes on actual Hanford tank waste sludge and the potential impacts on downstream pretreatment processing. The test material was a combination of reduction oxidation (REDOX) tank waste composited materials containing aluminum primarily in the form of boehmite and dissolved S saltcake containing Cr(III)-rich entrained solids. The pretreatment processing steps tested included • caustic leaching for Al removal • solids crossflow filtration through the cell unit filter (CUF) • stepwise solids washing using decreasing concentrations of sodium hydroxide with filtration through the CUF • oxidative leaching using sodium permanganate for removing Cr • solids filtration with the CUF • follow-on solids washing and filtration through the CUF • ion exchange processing for Cs removal • evaporation processing of waste stream recycle for volume reduction • combination of the evaporated product with dissolved saltcake. The effectiveness of each process step was evaluated by following the mass balance of key components (such as Al, B, Cd, Cr, Pu, Ni, Mn, and Fe), demonstrating component (Al, Cr, Cs) removal, demonstrating filterability by evaluating filter flux rates under various processing conditions (transmembrane pressure, crossflow velocities, wt% undissolved solids, and PSD) and filter fouling, and identifying potential issues for WTP. The filterability was reported separately (Shimskey et al. 2008) and is not repeated herein.

  6. Modelling of the reactive sputtering process with non-uniform discharge current density and different temperature conditions

    Science.gov (United States)

    Vašina, P; Hytková, T; Eliáš, M

    2009-05-01

    The majority of current models of the reactive magnetron sputtering assume a uniform shape of the discharge current density and the same temperature near the target and the substrate. However, in the real experimental set-up, the presence of the magnetic field causes high density plasma to form in front of the cathode in the shape of a toroid. Consequently, the discharge current density is laterally non-uniform. In addition to this, the heating of the background gas by sputtered particles, which is usually referred to as the gas rarefaction, plays an important role. This paper presents an extended model of the reactive magnetron sputtering that assumes the non-uniform discharge current density and which accommodates the gas rarefaction effect. It is devoted mainly to the study of the behaviour of the reactive sputtering rather that to the prediction of the coating properties. Outputs of this model are compared with those that assume uniform discharge current density and uniform temperature profile in the deposition chamber. Particular attention is paid to the modelling of the radial variation of the target composition near transitions from the metallic to the compound mode and vice versa. A study of the target utilization in the metallic and compound mode is performed for two different discharge current density profiles corresponding to typical two pole and multipole magnetics available on the market now. Different shapes of the discharge current density were tested. Finally, hysteresis curves are plotted for various temperature conditions in the reactor.

  7. Instrumentation and process control for fossil demonstration plants. Quarterly technical progress report, January--March 1977

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L.G.; O' Fallon, N.M.

    1977-09-01

    Progress during the quarter of January through March 1977 on ANL 189a 49622R2, Instrumentation and Process Control for Fossil Demonstration Plants (FDP) is reported. Work has been performed on updating the study of the state-of-the-art of instrumentation for Fossil Demonstration Plants (FDP), on development of mass-flow and other on-line instruments for FDP, process control analysis for FDP, and organization of a symposium on instrumentation and control for FDP. Progress in these areas is described.

  8. [Optimize the extraction process with supercritical CO2 fluid from lotus leaves by the uniform design and analysis on the chemical constituents by GC-MS].

    Science.gov (United States)

    Yin, Hui-jing; Qian, Yi-fan; Pu, Cun-hai

    2007-04-01

    To study the optimum parameters of the supercritical CO, fluid extraction of lotus leaves and chemical constituents of extractive matters. Supercritical CO2 fluid extraction condition was selected by uniform design. The extraction pressure, extraction temperature, extraction time were three factors in the experiment. GC-MS was applied for analyzing the extraction. The optimum condition were obtained: the extraction pressure was 26 Mpa, the extraction temperature was 40 degrees C, the extracion time was 90 minutes. The major constituent was 1H-Pyrrole-2-carboxaldehyde, 1-ethyl-in extractive matters. Uniform design can optimize the CO2 Supercritical Fluid Extraction process quickly and accuratly with satisfactory results.

  9. Development and Demonstration of a Biomass Boiler for Food Processing Applications

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-02-01

    Burns & McDonnell Engineering Company, in collaboration with Frito-Lay, Inc., Oak Ridge National Laboratory, CPL Systems, Inc., Alpha Boilers, and Kansas State University will demonstrate use of a biomass boiler in the food processing industry. The 60,000 lb/hr innovative biomass boiler system utilizing a combination of wood waste and tire-derived fuel (TDF) waste will offset all natural gas consumption at Frito-Lay's Topeka, Kansas, processing facility.

  10. West Valley demonstration project: alternative processes for solidifying the high-level wastes

    Energy Technology Data Exchange (ETDEWEB)

    Holton, L.K.; Larson, D.E.; Partain, W.L.; Treat, R.L.

    1981-10-01

    In 1980, the US Department of Energy (DOE) established the West Valley Solidification Project as the result of legislation passed by the US Congress. The purpose of this project was to carry out a high level nuclear waste management demonstration project at the Western New York Nuclear Service Center in West Valley, New York. The DOE authorized the Pacific Northwest Laboratory (PNL), which is operated by Battelle Memorial Institute, to assess alternative processes for treatment and solidification of the WNYNSC high-level wastes. The Process Alternatives Study is the suject of this report. Two pretreatment approaches and several waste form processes were selected for evaluation in this study. The two waste treatment approaches were the salt/sludge separation process and the combined waste process. Both terminal and interim waste form processes were studied.

  11. Data acquisition and processing in the ATLAS Tile Calorimeter Phase-II Upgrade Demonstrator

    CERN Document Server

    Valero, Alberto; The ATLAS collaboration

    2017-01-01

    The LHC has planned a series of upgrades culminating in the High Luminosity LHC which will have an average luminosity 5-7 times larger than the nominal Run-2 value. The ATLAS Tile Calorimeter (will undergo an upgrade to accommodate to the HL-LHC parameters. The TileCal readout electronics will be redesigned introducing a new readout strategy. A demonstrator drawer has been built to evaluate the new proposed readout architecture and prototypes of all the components. In the demonstrator, the detector data received in the TilePPr are stored in pipeline buffers and upon the reception of an external trigger signal the data events are processed, packed and readout in parallel through the legacy ROD system, the new Front-End Link eXchange system and an ethernet connection for monitoring purposes. This paper describes in detail the data processing and the hardware, firmware and software components of the TileCal demonstrator readout system.

  12. INTERNET RESOURCES SEARCH METHODOLOGY FOR DEMONSTRATION OF TECHNOLOGICAL PROCESSES IN CHEMISTRY STUDYING

    Directory of Open Access Journals (Sweden)

    Olga M. Naumenko

    2014-01-01

    Full Text Available The question of methodology of organization of search and application of Resources of the Internet is examined for demonstration of technological processes at the study of chemistry in senior school and higher educational establishments of І-ІІ levels of accreditation. Realization of positions of the new State standard of the base and complete secondary education needs creation of the certain methodical going near organization of search and use in the educational process of Resources of the Internet, that can be used in a course of chemistry for demonstration of their practical using, including technological processes. Considerable attention is devoted to advices for teachers in relation to methodology of the use of Resources of the Internet at preparation and realization of practical and laboratory work, other forms of students’ educational-searching activity.

  13. Speech processing system demonstrated by positron emission tomography (PET). A review of the literature

    Energy Technology Data Exchange (ETDEWEB)

    Hirano, Shigeru; Naito, Yasushi; Kojima, Hisayoshi [Kyoto Univ. (Japan)

    1996-03-01

    We review the literature on speech processing in the central nervous system as demonstrated by positron emission tomography (PET). Activation study using PET has been proved to be a useful and non-invasive method of investigating the speech processing system in normal subjects. In speech recognition, the auditory association areas and lexico-semantic areas called Wernicke`s area play important roles. Broca`s area, motor areas, supplementary motor cortices and the prefrontal area have been proved to be related to speech output. Visual speech stimulation activates not only the visual association areas but also the temporal region and prefrontal area, especially in lexico-semantic processing. Higher level speech processing, such as conversation which includes auditory processing, vocalization and thinking, activates broad areas in both hemispheres. This paper also discusses problems to be resolved in the future. (author) 42 refs.

  14. Demonstration of an N7 integrated fab process for metal oxide EUV photoresist

    Science.gov (United States)

    De Simone, Danilo; Mao, Ming; Kocsis, Michael; De Schepper, Peter; Lazzarino, Frederic; Vandenberghe, Geert; Stowers, Jason; Meyers, Stephen; Clark, Benjamin L.; Grenville, Andrew; Luong, Vinh; Yamashita, Fumiko; Parnell, Doni

    2016-03-01

    Inpria has developed a directly patternable metal oxide hard-mask as a robust, high-resolution photoresist for EUV lithography. In this paper we demonstrate the full integration of a baseline Inpria resist into an imec N7 BEOL block mask process module. We examine in detail both the lithography and etch patterning results. By leveraging the high differential etch resistance of metal oxide photoresists, we explore opportunities for process simplification and cost reduction. We review the imaging results from the imec N7 block mask patterns and its process windows as well as routes to maximize the process latitude, underlayer integration, etch transfer, cross sections, etch equipment integration from cross metal contamination standpoint and selective resist strip process. Finally, initial results from a higher sensitivity Inpria resist are also reported. A dose to size of 19 mJ/cm2 was achieved to print pillars as small as 21nm.

  15. Rationale, Design, and Methods for Process Evaluation in the Childhood Obesity Research Demonstration Project.

    Science.gov (United States)

    Joseph, Sitara; Stevens, Andria M; Ledoux, Tracey; O'Connor, Teresia M; O'Connor, Daniel P; Thompson, Debbe

    2015-01-01

    The cross-site process evaluation plan for the Childhood Obesity Research Demonstration (CORD) project is described here. The CORD project comprises 3 unique demonstration projects designed to integrate multi-level, multi-setting health care and public health interventions over a 4-year funding period. Three different communities in California, Massachusetts, and Texas. All CORD demonstration projects targeted 2-12-year-old children whose families are eligible for benefits under Title XXI (CHIP) or Title XIX (Medicaid). The CORD projects were developed independently and consisted of evidence-based interventions that aim to prevent childhood obesity. The interventions promote healthy behaviors in children by applying strategies in 4 key settings (primary care clinics, early care and education centers, public schools, and community institutions). The CORD process evaluation outlined 3 main outcome measures: reach, dose, and fidelity, on 2 levels (researcher to provider, and provider to participant). The plan described here provides insight into the complex nature of process evaluation for consortia of independently designed multi-level, multi-setting intervention studies. The process evaluation results will provide contextual information about intervention implementation and delivery with which to interpret other aspects of the program. Copyright © 2015 Society for Nutrition Education and Behavior. All rights reserved.

  16. A demonstrator analog signal processing circuit in a radiation hard SOI-CMOS technology

    CERN Document Server

    Anghinolfi, Francis; Campbell, M; Heijne, Erik H M; Jarron, Pierre; Meddeler, G; CERN. Geneva. Detector Research and Development Committee

    1990-01-01

    It is proposed to develop a demonstrator integrated circuit for particle detector analog signal processing using the advanced 1.2 micron HSOI3-HD Silicon-on-Insulator (SOI) CMOS radiation hard technology of Thomson-TMS, which has recently become accessible for selected civilian applications. The characteristics announced for this process promise survivability after a total dose in excess of 10 Mrad (SiO2) and 10**14 to 10**15 n/cm2, which is probably satisfactory for applications in LHC detector systems. The properties of such a SOI process look promising, in particular regarding speed. In view of the special analog requirements in the particle physics environment,one should verify the analog characteristics before and after irradiation by producing a demonstrator signal processing circuit which incorporates the most vital functional blocks. This demonstrator would consist of a low noise front-end amplifier, a comparator and an analog pipeline element with associated logic, following the scheme of the Hierarc...

  17. Advanced coal conversion process demonstration. Technical progress report, April 1--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high moisture, low rank coals to a high quality, low sulfur fuel, registered as the SynCoal{reg_sign} process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the coal is put through a deep bed stratifier cleaning process to separate the pyrite rich ash from the coal. The SynCoal process enhances low rank, western coals, usually with a moisture content of 25 to 55 percent, sulfur content of 0.5 to 1.5 percent, and heating value of 5,500 to 9,000 Btu/lb, by producing a stable, upgraded, coal product with a moisture content as low as 1 percent, sulfur content as low as 0.3 percent, and heating value up to 12,000 Btu/lb. The 45 ton per hour unit is located adjacent to a unit train load out facility at Western Energy Company`s Rosebud coal mine near Colstrip, Montana. The demonstration plant is sized at about one-tenth the projected throughput of a multiple processing train commercial facility. During this report period the primary focus has been to continue the operation of the demonstration facility. Production has been going to area power plants. Modifications and maintenance work was also performed this quarter.

  18. Advanced Coal Conversion Process Demonstration Project. Final technical progress report, January 1, 1995--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from January 1, 1995 through December 31, 1995. This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low-rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal Process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the coal is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal. The SynCoal Process enhances low-rank, western coals, usually with a moisture content of 25 to 55 percent, sulfur content of 0.5 to 1.5 percent, and heating value of 5,5000 to 9,000 British thermal units per pound (Btu/lb), by producing a stable, upgraded, coal product with a moisture content as low as 1 percent, sulfur content as low as 0.3 percent, and heating value up to 12,000 Btu/lb. During this reporting period, the primary focus for the ACCP Demonstration Project team was to expand SynCoal market awareness and acceptability for both the products and the technology. The ACCP Project team continued to focus on improving the operation, developing commercial markets, and improving the SynCoal products as well as the product`s acceptance.

  19. An ergonomics action research demonstration: integrating human factors into assembly design processes.

    Science.gov (United States)

    Village, J; Greig, M; Salustri, F; Zolfaghari, S; Neumann, W P

    2014-01-01

    In action research (AR), the researcher participates 'in' the actions in an organisation, while simultaneously reflecting 'on' the actions to promote learning for both the organisation and the researchers. This paper demonstrates a longitudinal AR collaboration with an electronics manufacturing firm where the goal was to improve the organisation's ability to integrate human factors (HF) proactively into their design processes. During the three-year collaboration, all meetings, workshops, interviews and reflections were digitally recorded and qualitatively analysed to inform new 'actions'. By the end of the collaboration, HF tools with targets and sign-off by the HF specialist were integrated into several stages of the design process, and engineers were held accountable for meeting the HF targets. We conclude that the AR approach combined with targeting multiple initiatives at different stages of the design process helped the organisation find ways to integrate HF into their processes in a sustainable way. Researchers acted as a catalyst to help integrate HF into the engineering design process in a sustainable way. This paper demonstrates how an AR approach can help achieve HF integration, the benefits of using a reflective stance and one method for reporting an AR study.

  20. Demonstration of base catalyzed decomposition process, Navy Public Works Center, Guam, Mariana Islands

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, A.J.; Freeman, H.D.; Brown, M.D.; Zacher, A.H.; Neuenschwander, G.N.; Wilcox, W.A.; Gano, S.R. [Pacific Northwest National Lab., Richland, WA (United States); Kim, B.C.; Gavaskar, A.R. [Battelle Columbus Div., OH (United States)

    1996-02-01

    Base Catalyzed Decomposition (BCD) is a chemical dehalogenation process designed for treating soils and other substrate contaminated with polychlorinated biphenyls (PCB), pesticides, dioxins, furans, and other hazardous organic substances. PCBs are heavy organic liquids once widely used in industry as lubricants, heat transfer oils, and transformer dielectric fluids. In 1976, production was banned when PCBs were recognized as carcinogenic substances. It was estimated that significant quantities (one billion tons) of U.S. soils, including areas on U.S. military bases outside the country, were contaminated by PCB leaks and spills, and cleanup activities began. The BCD technology was developed in response to these activities. This report details the evolution of the process, from inception to deployment in Guam, and describes the process and system components provided to the Navy to meet the remediation requirements. The report is divided into several sections to cover the range of development and demonstration activities. Section 2.0 gives an overview of the project history. Section 3.0 describes the process chemistry and remediation steps involved. Section 4.0 provides a detailed description of each component and specific development activities. Section 5.0 details the testing and deployment operations and provides the results of the individual demonstration campaigns. Section 6.0 gives an economic assessment of the process. Section 7.0 presents the conclusions and recommendations form this project. The appendices contain equipment and instrument lists, equipment drawings, and detailed run and analytical data.

  1. Demonstration of base catalyzed decomposition process, Navy Public Works Center, Guam, Mariana Islands

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, A.J.; Freeman, H.D.; Brown, M.D.; Zacher, A.H.; Neuenschwander, G.N.; Wilcox, W.A.; Gano, S.R. [Pacific Northwest National Lab., Richland, WA (United States); Kim, B.C.; Gavaskar, A.R. [Battelle Columbus Div., OH (United States)

    1996-02-01

    Base Catalyzed Decomposition (BCD) is a chemical dehalogenation process designed for treating soils and other substrate contaminated with polychlorinated biphenyls (PCB), pesticides, dioxins, furans, and other hazardous organic substances. PCBs are heavy organic liquids once widely used in industry as lubricants, heat transfer oils, and transformer dielectric fluids. In 1976, production was banned when PCBs were recognized as carcinogenic substances. It was estimated that significant quantities (one billion tons) of U.S. soils, including areas on U.S. military bases outside the country, were contaminated by PCB leaks and spills, and cleanup activities began. The BCD technology was developed in response to these activities. This report details the evolution of the process, from inception to deployment in Guam, and describes the process and system components provided to the Navy to meet the remediation requirements. The report is divided into several sections to cover the range of development and demonstration activities. Section 2.0 gives an overview of the project history. Section 3.0 describes the process chemistry and remediation steps involved. Section 4.0 provides a detailed description of each component and specific development activities. Section 5.0 details the testing and deployment operations and provides the results of the individual demonstration campaigns. Section 6.0 gives an economic assessment of the process. Section 7.0 presents the conclusions and recommendations form this project. The appendices contain equipment and instrument lists, equipment drawings, and detailed run and analytical data.

  2. Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structures

    Science.gov (United States)

    Sheppard, C. H.; Hoggatt, J. T.; Hunter, A. B.

    1979-01-01

    The work included establishing controls on the polymer, the prepreg, composite fabrication, and quality assurance, as well as fabrication of structural elements to demonstrate the developed materials and processes. The fabricated structures were hat sections, I-beam sections, honeycomb sandwich structures, and molded graphite-reinforced fittings. The graphite/PMR-15 polyimide system was shown to be well suited for use in the 550-600 F temperature range; the processing techniques developed were proved and found potentially useful for other commercially available systems.

  3. COMMERCIAL-SCALE DEMONSTRATION OF THE LIQUID PHASE METHANOL (LPMEOH) PROCESS

    Energy Technology Data Exchange (ETDEWEB)

    E.C. Heydorn; B.W. Diamond; R.D. Lilly

    2003-06-01

    This project, which was sponsored by the U.S. Department of Energy (DOE) under the Clean Coal Technology Program to demonstrate the production of methanol from coal-derived synthesis gas (syngas), has completed the 69-month operating phase of the program. The purpose of this Final Report for the ''Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) Process'' is to provide the public with details on the performance and economics of the technology. The LPMEOH{trademark} Demonstration Project was a $213.7 million cooperative agreement between the DOE and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). The DOE's cost share was $92,708,370 with the remaining funds coming from the Partnership. The LPMEOH{trademark} demonstration unit is located at the Eastman Chemical Company (Eastman) chemicals-from-coal complex in Kingsport, Tennessee. The technology was the product of a cooperative development effort by Air Products and Chemicals, Inc. (Air Products) and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} Process is ideally suited for directly processing gases produced by modern coal gasifiers. Originally tested at the Alternative Fuels Development Unit (AFDU), a small, DOE-owned process development facility in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst, and allowing the methanol synthesis reaction to proceed at higher rates. The LPMEOH{trademark} Demonstration Project accomplished the objectives set out in the Cooperative Agreement with DOE for this Clean

  4. Proceedings of the 1977 symposium on instrumentation and process control for fossil demonstration plants

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    The 1977 Symposium on Instrumentation and Process Control for Fossil Demonstration Plants was held at Hyatt Regency O'Hare, Chicago, Illinois, July 13 to 15, 1977. It was sponsored by the Argonne National Laboratory, the U.S. Energy Research and Development Administration and the Instrument Society of America (Chicago Section). Seventeen papers from thee proceedings were entered individually into EDB and ERA (three papers weree entered previously). (LTN)

  5. Cesium removal demonstration utilizing crystalline silicotitanate sorbent for processing Melton Valley Storage Tank supernate: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Walker, J.F. Jr.; Taylor, P.A.; Cummins, R.L. [and others

    1998-03-01

    This report provides details of the Cesium Removal Demonstration (CsRD), which was conducted at Oak Ridge National Laboratory (ORNL) on radioactive waste from the Melton Valley Storage Tanks. The CsRD was the first large-scale use of state-of-the-art sorbents being developed by private industry for the selective removal of cesium and other radionuclides from liquid wastes stored across the DOE complex. The crystalline silicotitanate sorbent used in the demonstration was chosen because of its effectiveness in laboratory tests using bench-scale columns. The demonstration showed that the cesium could be removed from the supernate and concentrated on a small-volume, solid waste form that would meet the waste acceptance criteria for the Nevada Test Site. During this project, the CsRD system processed > 115,000 L (30,000 gal) of radioactive supernate with minimal operational problems. Sluicing, drying, and remote transportation of the sorbent, which could not be done on a bench scale, were successfully demonstrated. The system was then decontaminated to the extent that it could be contact maintained with the use of localized shielding only. By utilizing a modular, transportable design and placement within existing facilities, the system can be transferred to different sites for reuse. The initial unit has now been removed from the process building and is presently being reinstalled for use in baseline operations at ORNL.

  6. ACSEPT, a European project for a new step in the future demonstration of advanced fuel processing

    Energy Technology Data Exchange (ETDEWEB)

    Bourg, S. [CEA Marcoule 30 (France); Hill, C. [CEA Saclay, 91 - Gif sur Yvette (France); Caravaca, C.; Espartero, A. [Ciemat, Madrid (Spain); Rhodes, C.; Taylor, R.; Harrison, M. [National Nuclear Laboratory (United Kingdom); Geist, A. [Fachinformationszentrum Karlsruhe - INE (Germany); Modolo, G. [Forschungszentrum Juelich - FZJ (Germany); Cassayre, L. [Centre National de la Recherche Scientifique (CNRS), 91 - Orsay (France); Malmbeck, R. [Joint Research Centre (JRC) - Institute for Transuranium Elements (ITU) (Germany); De Angelis, G. [ENEA, Bologna (Italy); Bouvet, S. [Alcan, 92 - Courbevoie (France); Klaassen, F. [Nuclear Research and consultancy Group (NRG) (Netherlands); Ekber, C.

    2010-11-15

    Partitioning and transmutation, associated to a multi-recycling of all transuranics should play a key role in the development of sustainable nuclear energy. By joining together 34 partners coming from European universities, nuclear research laboratories and major industrial players, in a multi-disciplinary consortium, the FP7-Euratom-Fission collaborative project ACSEPT (Actinide recycling by separation and transmutation), provides the sound basis and future improvements for future demonstrations of fuel treatment in strong connection with fuel fabrication techniques. ACSEPT is organized into 3 technical domains: 1) selecting and optimizing mature aqueous separation processes (Diamex-Sanex, Ganex); 2) high temperature pyrochemical separation processes, and 3) carrying out engineering and systems studies on hydro- and pyro-chemical processes to prepare for future demonstration at a pilot level. After 2 years of work, 2 successful hot-tests were performed in hydrometallurgy, validating the Sanex and i-Sanex routes. Efforts are now devoted to the Ganex concept. Progress was also made in fuel dissolution and fuel re-fabrication. In pyrometallurgy, promising routes are almost demonstrated for the actinide recovery from aluminium. (A.C.)

  7. FY13 GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATIONS OF THE DWPF CHEMICAL PROCESS CELL WITH SIMULANTS

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Zamecnik, J.; Best, D.

    2014-03-13

    Savannah River Remediation is evaluating changes to its current Defense Waste Processing Facility flowsheet to replace formic acid with glycolic acid in order to improve processing cycle times and decrease by approximately 100x the production of hydrogen, a potentially flammable gas. Higher throughput is needed in the Chemical Processing Cell since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the safety significant gas chromatographs and the potential for production of flammable quantities of hydrogen, eliminating the use of formic acid is highly desirable. Previous testing at the Savannah River National Laboratory has shown that replacing formic acid with glycolic acid allows the reduction and removal of mercury without significant catalytic hydrogen generation. Five back-to-back Sludge Receipt and Adjustment Tank (SRAT) cycles and four back-to-back Slurry Mix Evaporator (SME) cycles were successful in demonstrating the viability of the nitric/glycolic acid flowsheet. The testing was completed in FY13 to determine the impact of process heels (approximately 25% of the material is left behind after transfers). In addition, back-to-back experiments might identify longer-term processing problems. The testing was designed to be prototypic by including sludge simulant, Actinide Removal Product simulant, nitric acid, glycolic acid, and Strip Effluent simulant containing Next Generation Solvent in the SRAT processing and SRAT product simulant, decontamination frit slurry, and process frit slurry in the SME processing. A heel was produced in the first cycle and each subsequent cycle utilized the remaining heel from the previous cycle. Lower SRAT purges were utilized due to the low hydrogen generation. Design basis addition rates and boilup rates were used so the processing time was shorter than current processing rates.

  8. California Food Processing Industry Wastewater Demonstration Project: Phase I Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, Glen; Atkinson, Barbara; Rhyne, Ivin

    2009-09-09

    Wastewater treatment is an energy-intensive process and electricity demand is especially high during the utilities summer peak electricity demand periods. This makes wastewater treatment facilities prime candidates for demand response programs. However, wastewater treatment is often peripheral to food processing operations and its demand response opportunities have often been overlooked. Phase I of this wastewater demonstration project monitored wastewater energy and environmental data at Bell-Carter Foods, Inc., California's largest olive processing plant. For this monitoring activity the project team used Green Energy Management System (GEMS) automated enterprise energy management (EEM) technologies. This report presents results from data collected by GEMS from September 15, 2008 through November 30, 2008, during the olive harvest season. This project established and tested a methodology for (1) gathering baseline energy and environmental data at an industrial food-processing plant and (2) using the data to analyze energy efficiency, demand response, daily peak load management, and environmental management opportunities at the plant. The Phase I goals were to demonstrate the measurement and interrelationship of electricity demand, electricity usage, and water quality metrics and to estimate the associated CO{sub 2} emissions.

  9. Demonstrating Compliance with Stringent Nitrogen Limits Using a Biological Nutrient Removal Process in California's Central Valley.

    Science.gov (United States)

    Merlo, Rion; Witzgall, Bob; Yu, William; Ohlinger, Kurt; Ramberg, Steve; De Las Casas, Carla; Henneman, Seppi; Parker, Denny

    2015-12-01

    The Sacramento Regional County Sanitation District (District) must be compliant with stringent nitrogen limits by 2021 that the existing treatment facilities cannot meet. An 11-month pilot study was conducted to confirm that these limits could be met with an air activated sludge biological nutrient removal (BNR) process. The pilot BNR treated an average flow of 946 m(3)/d and demonstrated that it could reliably meet the ammonia limit, but that external carbon addition may be necessary to satisfy the nitrate limit. The BNR process performed well throughout the 11 months of operation with good settleability, minimal nocardioform content, and high quality secondary effluent. The BNR process was operated at a minimum pH of 6.4 with no noticeable impact to nitrification rates. Increased secondary sludge production was observed during rainfall events and is attributed to a change in wastewater influent characteristics.

  10. Theoretical Analysis of Unit Friction Force Working on the Metal Contact Surface with the Roll Change during Feedstock with Non-Uniform Temperature Distribution Rolling Process

    Directory of Open Access Journals (Sweden)

    Sygut P.

    2016-06-01

    Full Text Available The paper presents the results of theoretical studies influence of non-uniform temperature distribution along the feedstock length to the unit friction force working on the metal contact surface with the roll change during the round bars 70 mm in diameter continuous rolling process. This value is one of the major factors affecting the grooves wear during the rolling process. The studies were carried out based on the actual engineering data for 160 × 160 mm square cross-section feedstock of steel S355J0. Numerical modelling of the rolling process was performed using Forge2008®, a finite-element based computer program.

  11. Thermally dried ink-jet process for 6,13-bis(triisopropylsilylethynyl)-pentacene for high mobility and high uniformity on a large area substrate

    Science.gov (United States)

    Ryu, Gi Seong; Lee, Myung Won; Jeong, Seung Hyeon; Song, Chung Kun

    2012-01-01

    In this study we developed a simple ink-jet process for 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene), which is known as a high-mobility soluble organic semiconductor, to achieve relatively high-mobility and high-uniformity performance for large-area applications. We analyzed the behavior of fluorescent particles in droplets and applied the results to determining a method of controlling the behavior of TIPS-pentacene molecules. The grain morphology of TIPS-pentacene varied depending on the temperature applied to the droplets during drying. We were able to obtain large and uniform grains at 46 degrees C without any "coffee stain". The process was applied to a large-size organic thin-film transistor (OTFT) backplane for an electrophoretic display panel containing 192 x 150 pixels on a 6-in.-sized substrate. The average of mobilities of 36 OTFTs, which were taken from different locations of the backplane, was 0.44 +/- 0.08 cm2.V-1.s-1, with a small deviation of 20%, over a 6-in.-size area comprising 28,800 OTFTs. This process providing high mobility and high uniformity can be achieved by simply maintaining the whole area of the substrate at a specific temperature (46 degrees C in this case) during drying of the droplets.

  12. Quantifying physical structure changes and non-uniform water flow in cattle manure during dry anaerobic digestion process at lab scale: Implication for biogas production.

    Science.gov (United States)

    André, L; Durante, M; Pauss, A; Lespinard, O; Ribeiro, T; Lamy, E

    2015-09-01

    The aim of this study was to investigate and quantify non-uniform water flow during dry AD and its implication for biogas production. Laboratory tracer experiments were performed on cattle manure over the course of AD. The evolution of the permeability, the dry bulk density, the dry porosity, the total and volatile solid contents of cattle manure at different stages of AD, revealed waste structure changes, impacting water flow and methane production. Tracer experiments and numerical modeling performed by using a physical non-equilibrium model indicated non-uniform preferential flow patterns during degradation. According to literature, the increase of inoculum recirculation frequency improved methane production rate. However, these results demonstrated that this improvement occurs only at the beginning of manure degradation. After 19 days of degradation the inoculum recirculation and the flow patterns modification had no effect on methane production rate.

  13. ACSEPT a European project for a new step in the future demonstration of advanced fuel processing

    Energy Technology Data Exchange (ETDEWEB)

    Bourg, S.; Hill, C. [CEA, DRCP - Bat 181, CEA Marcoule, BP17171, 30207 Bagnols/Ceze (France); Caravaca, C.; Espartero, A. [CIEMAT, Avda. Complutense, 22 - 28040 Madrid (Spain); Rhodes, C.; Taylor, R.; Harrison, M. [National Nuclear Laboratory, Sellafield, Seascale, Cumbria, CA20 1PG (United Kingdom); EKBERG, C. [Chalmers tekniska hoegskola, Institutionen foer kemi- och bioteknik, Aemnesomraadets namn, 412 96 Goeteborg (Sweden); GEIST, A. [Forschungszentrum Karlsruhe, Institut fuer Nukleare Entsorgungstechnik, P.O.B. 3640, D-76021 Karlsruhe (Germany); Modolo, G. [Forschungszentrum Juelich - FZJ, D-52425 Juelich (Germany); Cassayre, L. [CNRS, Laboratoire de Genie Chimique, Toulouse (France); Malmbeck, R. [JRC-ITU, Karlsruhe (Germany); De Angelis, G. [ENEA, Casaccia, Rome (Italy); Bouvet, S. [Rio Tinto Alcan, Centre de Recherche de Voreppe, Voreppe (France); Klaassen, F. [NRG, PO Box 25, NL-1755 ZG Petten (Netherlands)

    2010-07-01

    For more than fifteen years, a European scientific community has joined its effort to develop and optimise processes for the partitioning of actinides from fission products. In an international context of 'nuclear renaissance', the upcoming of a new generation of nuclear reactor (Gen IV) will require the development of associated advanced closed fuel cycles which answer the needs of a sustainable nuclear energy: the minimization of the production of long lived radioactive waste but also the optimization of the use of natural resources with an increased resistance to proliferation. Actually, Partitioning and Transmutation (P and T), associated to a multi-recycling of all transuranics (TRUs), should play a key role in the development of this sustainable nuclear energy. By joining together 34 Partners coming from European universities, nuclear research bodies and major industrial players in a multidisciplinary consortium, the FP7 EURATOM-Fission Collaborative Project ACSEPT (Actinide recycling by Separation and Transmutation), started in 2008 for four year duration, provides the sound basis and fundamental improvements for future demonstrations of fuel treatment in strong connection with fuel fabrication techniques. Consistently with potentially viable recycling strategies, ACSEPT therefore provides a structured R and D framework to develop chemical separation processes compatible with fuel fabrication techniques, with a view to their future demonstration at the pilot level. ACSEPT is organized into three technical domains: (i) Considering technically mature aqueous separation processes, ACSEPT works to optimize and select the most promising ones dedicated either to actinide partitioning or to group actinide separation. (ii) Concerning high temperature pyrochemical separation processes, ACSEPT focuses on the enhancement of the two reference cores of process selected within previous projects. R and D efforts are now devoted to key scientific and technical

  14. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1997-09-30

    The Liquid Phase Methanol (LPMEOH) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). Ak Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOITM Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this reporting period, DOE accepted the recommendation to continue with dimethyl ether (DME) design verification testing (DVT). DME design verification testing studies show the liquid phase DME (LPDME) process will have a significant economic advantage for the coproduction of DME for local markets. An LPDME catalyst system with reasonable long-term activity and stzibility is being developed. Planning for a proof-of-concept test run at the LaPorte Alternative Fuels Development Unit (AFDU) was recommended. DOE issued a letter dated 31 July 1997 accepting the recommendation to continue design verification testing. In order to allow for scale-up of the manufacturing technique for the dehydration catalyst from the pilot plant to the commercial scale, the time required to produce the catalyst to the AFDU has slipped. The new estimated delivery date is 01 June 1998.

  15. Integrated DWPF Melter System (IDMS) campaign report: Hanford Waste Vitrification Plan (HWVP) process demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Hutson, N.D.

    1992-08-10

    Vitrification facilities are being developed worldwide to convert high-level nuclear waste to a durable glass form for permanent disposal. Facilities in the United States include the Department of Energy`s Defense Waste Processing Facility (DWPF) at the Savannah River Site, the Hanford Waste Vitrification Plant (HWVP) at the Hanford Site and the West Valley Demonstration Project (WVDP) at West Valley, NY. At each of these sites, highly radioactive defense waste will be vitrified to a stable borosilicate glass. The DWPF and WVDP are near physical completion while the HWVP is in the design phase. The Integrated DWPF Melter System (IDMS) is a vitrification test facility at the Savannah River Technology Center (SRTC). It was designed and constructed to provide an engineering-scale representation of the DWPF melter and its associated feed preparation and off-gas treatment systems. Because of the similarities of the DWPF and HWVP processes, the IDMS facility has also been used to characterize the processing behavior of a reference NCAW simulant. The demonstration was undertaken specifically to determine material balances, to characterize the evolution of offgas products (especially hydrogen), to determine the effects of noble metals, and to obtain general HWVP design data. The campaign was conducted from November, 1991 to February, 1992.

  16. A Novel Self-aligned and Maskless Process for Formation of Highly Uniform Arrays of Nanoholes and Nanopillars

    Directory of Open Access Journals (Sweden)

    Wu Wei

    2008-01-01

    Full Text Available AbstractFabrication of a large area of periodic structures with deep sub-wavelength features is required in many applications such as solar cells, photonic crystals, and artificial kidneys. We present a low-cost and high-throughput process for realization of 2D arrays of deep sub-wavelength features using a self-assembled monolayer of hexagonally close packed (HCP silica and polystyrene microspheres. This method utilizes the microspheres as super-lenses to fabricate nanohole and pillar arrays over large areas on conventional positive and negative photoresist, and with a high aspect ratio. The period and diameter of the holes and pillars formed with this technique can be controlled precisely and independently. We demonstrate that the method can produce HCP arrays of hole of sub-250 nm size using a conventional photolithography system with a broadband UV source centered at 400 nm. We also present our 3D FDTD modeling, which shows a good agreement with the experimental results.

  17. DEVELOPMENT AND DEMONSTRATION OF INTEGRATED CARBON RECOVERY SYSTEMS FROM FINE COAL PROCESSING WASTE

    Energy Technology Data Exchange (ETDEWEB)

    Y.P. Chugh; D. Patil; A. Patwardhan; R.Q. Honaker; B.K. Parekh; D. Tao; Latif Khan

    2000-07-01

    The project involves the development of an efficient, environmentally friendly system for the economical recovery of carbon from fine-coal refuse ponds. The project will be conducted in two phases. Phase I was involved in the development and evaluation of process equipment and techniques to be used in carbon recovery, product dewatering and reconstitution, and refuse management. Phase II will integrate the various units into a continuously operating circuit that will be demonstrated at a site selected based on the results presented in this study.

  18. Instrumentation and process control for fossil demonstration plants. Quarterly technical progress report, April--June 1977

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L.G.

    1977-07-01

    Work has been performed on updating the study of the state-of-the-art of instrumentation for Fossil Demonstration Plants (FDP), development of mass-flow and other on-line instruments for FDP, process control analysis for FDP, and organization of a symposium on instrumentation and control for FDP. A Solids/Gas Flow Test Facility (S/GFTF) under construction for instrument development, testing, evaluation, and calibration is described. The development work for several mass-flow and other on-line instruments is described: acoustic flowmeter, capacitive density flowmeter, neutron activation flowmeter and composition analysis system, gamma ray correlation flowmeter, optical flowmeter, and capacitive liquid interface level meter.

  19. Instrumentation and process control for fossil demonstration plants. Annual technical progress report, October 1976--September 1977

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L. G.; O' Fallon, N. M.

    1977-10-01

    Progress on Instrumentation and Process Control for Fossil Demonstration Plants (FDP) is reported. Work has been performed on updating the study of the state-of-the-art of instrumentation for FDP, development of mass-flow and other on-line instruments for FDP, process control analysis for FDP, and organization of a symposium on instrumentation and control for FDP. A Solids/Gas Flow Test Facility (S/GFTF) under construction for instrument development, testing, evaluation, and calibration is described. The development work for several mass-flow and other on-line instruments is described: acoustic flowmeter, capacitive density flowmeter, neutron activation flowmeter, gamma ray correlation flowmeter, optical flowmeter, composition analysis system, and capacitive liquid interface level meter.

  20. Strategy for verification and demonstration of the sealing process for canisters for spent fuel

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Christina [Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin (Germany); Oeberg, Tomas [Tomas Oeberg Konsult AB, Lyckeby (Sweden)

    2004-08-01

    Electron beam welding and friction stir welding are the two processes now being considered for sealing copper canisters with Sweden's radioactive waste. This report outlines a strategy for verification and demonstration of the encapsulation process which here is considered to consist of the sealing of the canister by welding followed by quality control of the weld by non-destructive testing. Statistical methodology provides a firm basis for modern quality technology and design of experiments has been successful part of it. Factorial and fractional factorial designs can be used to evaluate main process factors and their interactions. Response surface methodology with multilevel designs enables further optimisation. Empirical polynomial models can through Taylor series expansions approximate the true underlying relationships sufficiently well. The fitting of response measurements is based on ordinary least squares regression or generalised linear methods. Unusual events, like failures in the lid welds, are best described with extreme value statistics and the extreme value paradigm give a rationale for extrapolation. Models based on block maxima (the generalised extreme value distribution) and peaks over threshold (the generalised Pareto distribution) are considered. Experiences from other fields of the materials sciences suggest that both of these approaches are useful. The initial verification experiments of the two welding technologies considered are suggested to proceed by experimental plans that can be accomplished with only four complete lid welds each. Similar experimental arrangements can be used to evaluate process 'robustness' and optimisation of the process window. Two series of twenty demonstration trials each, mimicking assembly-line production, are suggested as a final evaluation before the selection of welding technology. This demonstration is also expected to provide a data base suitable for a baseline estimate of future performance

  1. Rates of uniform convergence for empirical processes of strictly stationaryβ-mixing sequences indexed by an unbounded class of functions

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Dixin张涤新

    2002-01-01

    Assume that {Xn} is a strictly stationary β-mixing random sequence with the β-mixing coefficient βk = O(k-r), 0 2 or p > 4, uniform convergence rates of empirical processes of strictly stationary β-mixing random sequence over the index classes can reach O((nr/(l+r)/logn)-1/2) or O((nr/(1+r)/ log n)-3/4) and that the Central Limit Theorem does not always hold for the empirical processes.``

  2. Advanced aqueous reprocessing in P and T strategies: process demonstrations on genuine fuels and targets

    Energy Technology Data Exchange (ETDEWEB)

    Satmark, B.; Apostolidis, C.; Courson, O.; Malmbeck, R.; Carlos, R.; Pagliosa, G.; Romer, K.; Glatz, J.P. [European Commission, DG-JRC, Institute for Transuranium Elements, Hot Cell Technology, Karlsruhe (Germany)

    2000-07-01

    In the present work the performance of several processes used for advanced reprocessing of commercial LWR fuels as well as transmutation targets is compared. As a first step uranium and plutonium were recovered by PUREX type reprocessing. The raffinate, containing fission products, lanthanides and the minor actinides (MA) were used as feed for the second step in which minor actinides and lanthanides were separated from the bulk of the fission products. The five different processes tested use CMPO, DIDPA, TRPO, Diamide and CYANEX 923 as extractant. In the third step MA are separated from lanthanides. Here three processes were tested, i.e. using CYANEX 301, the synergistic mixture of di-chloro substituted CYANEX 301 and TOPO, and BTP solvents. Column-, batch- and continuous counter-current extraction techniques were used for the tests. The different processes will be described and discussed in terms of performances and efficiencies for Am and Cm. Efficient separation of MA from different genuine fuel solutions could be demonstrated and thereby also the possibility of closing a future transmutation fuel cycle. The combination, Diamide and BTP was found to be the best among extractants tested to achieve an efficient MA recovery from spent fuel. (authors)

  3. Advanced aqueous reprocessing in P and T strategies: process demonstrations on genuine fuels and targets

    Energy Technology Data Exchange (ETDEWEB)

    Christiansen, B.; Apostolidis, C.; Carlos, R.; Courson, O.; Glatz, J.P.; Malmbeck, R.; Pagliosa, G.; Roemer, K.; Serrano-Purroy, D. [European Commission, JRC, Inst. for Transuranium Elements, Karlsruhe (Germany)

    2004-07-01

    In the present work the performance of several processes used for advanced reprocessing of commercial LWR fuels as well as transmutation targets is compared. As a first step uranium and plutonium were recovered by PUREX type reprocessing. The raffinate, containing fission products including lanthanides and the minor actinides (MA) was used as feed for the second step in which minor actinides and lanthanides were separated from the bulk of the fission products. The five different processes tested use CMPO, DIDPA, TRPO, diamide and CYANEX 923 as extractants. In the third step MA are separated from lanthanides. Here three processes were tested, i.e. using CYANEX 301, the synergistic mixture of di-chloro substituted CYANEX 301 and TOPO, and BTP solvents. Column-, batch- and continuous counter-current extraction techniques were used for the tests. The different processes will be described and discussed in terms of performances and efficiencies for Am and Cm separation. Efficient separation of MA from different genuine fuel solutions could be demonstrated and thereby also the possibility of closing a future transmutation fuel cycle. The combination of diamide and BTP seems to be the best, among extractants tested, to achieve an efficient MA recovery from spent fuel. (orig.)

  4. Industrial demonstration plant for the gasification of herb residue by fluidized bed two-stage process.

    Science.gov (United States)

    Zeng, Xi; Shao, Ruyi; Wang, Fang; Dong, Pengwei; Yu, Jian; Xu, Guangwen

    2016-04-01

    A fluidized bed two-stage gasification process, consisting of a fluidized-bed (FB) pyrolyzer and a transport fluidized bed (TFB) gasifier, has been proposed to gasify biomass for fuel gas production with low tar content. On the basis of our previous fundamental study, an autothermal two-stage gasifier has been designed and built for gasify a kind of Chinese herb residue with a treating capacity of 600 kg/h. The testing data in the operational stable stage of the industrial demonstration plant showed that when keeping the reaction temperatures of pyrolyzer and gasifier respectively at about 700 °C and 850 °C, the heating value of fuel gas can reach 1200 kcal/Nm(3), and the tar content in the produced fuel gas was about 0.4 g/Nm(3). The results from this pilot industrial demonstration plant fully verified the feasibility and technical features of the proposed FB two-stage gasification process.

  5. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOTH) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1998-12-21

    The Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOI-P Process Demonstration Unit was built at a site located at the Eastman coal-to-chemicals complex in Kingsport. During this quarter, initial planning and procurement work continued on the seven project sites which have been accepted for participation in the off-site, product-use test program. Approximately 12,000 gallons of fuel-grade methanol (98+ wt% methanol, 4 wt% water) produced during operation on carbon monoxide (CO)-rich syngas at the LPMEOW Demonstration Unit was loaded into trailers and shipped off-site for Mure product-use testing. At one of the projects, three buses have been tested on chemical-grade methanol and on fhel-grade methanol from the LPMEOW Demonstration Project. During the reporting period, planning for a proof-of-concept test run of the Liquid Phase Dimethyl Ether (LPDME~ Process at the Alternative Fuels Development Unit (AFDU) in LaPorte, TX continued. The commercial catalyst manufacturer (Calsicat) has prepared the first batch of dehydration catalyst in large-scale equipment. Air Products will test a sample of this material in the laboratory autoclave. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for freshly reduced catalyst (as determined in the laborato~ autoclave), was monitored for the initial extended operation at the lower initial reactor operating temperature of 235oC. At this condition, the decrease in catalyst activity with time from the period 20 December 1997 through 27 January 1998 occurred at a rate of 1.0% per

  6. Field Demonstration of a Membrane Process to Separate Nitrogen from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    Kaaeid Lokhandwala

    2007-03-31

    The original proposal described the construction and operation of a 1 MMscfd treatment system to be operated at a Butcher Energy gas field in Ohio. The gas produced at this field contained 17% nitrogen. During pre-commissioning of the project, a series of well tests showed that the amount of gas in the field was significantly smaller than expected and that the nitrogen content of the wells was very high (25 to 30%). After evaluating the revised cost of the project, Butcher Energy decided that the plant would not be economical and withdrew from the project. Since that time, Membrane Technology and Research, Inc. (MTR) has signed a marketing and sales partnership with ABB Lummus Global, a large multinational corporation. MTR is working with the company's Randall Gas Technology group, a supplier of equipment and processing technology to the natural gas industry. Randall's engineering group found a new site for the project at a North Texas Exploration (NTE) gas processing plant, which met with limited success. However, a small test system was installed at a Twin Bottoms Energy well in Kentucky. This unit operated successfully for six months, and demonstrated the technology's reliability on a small scale. MTR then located an alternative test site with much larger gas flow rates and signed a contract with Towne Exploration in the third quarter of 2006, for a demonstration plant in Rio Vista, California, to be run through May 2007. The demonstration for Towne has already resulted in the sale of two commercial skids to the company; both units will be delivered by the end of 2007. Total sales of nitrogen/natural gas membrane separation units from the partnership with ABB are now approaching $4.0 million.

  7. West Valley Demonstration Project vitrification process equipment Functional and Checkout Testing of Systems (FACTS)

    Energy Technology Data Exchange (ETDEWEB)

    Carl, D.E.; Paul, J.; Foran, J.M.; Brooks, R.

    1990-09-30

    The Vitrification Facility (VF) at the West Valley Demonstration Project was designed to convert stored radioactive waste into a stable glass for disposal in a federal repository. The Functional and Checkout Testing of Systems (FACTS) program was conducted from 1984 to 1989. During this time new equipment and processes were developed, installed, and implemented. Thirty-seven FACTS tests were conducted, and approximately 150,000 kg of glass were made by using nonradioactive materials to simulate the radioactive waste. By contrast, the planned radioactive operation is expected to produce approximately 500,000 kg of glass. The FACTS program demonstrated the effectiveness of equipment and procedures in the vitrification system, and the ability of the VF to produce quality glass on schedule. FACTS testing also provided data to validate the WVNS waste glass qualification method and verify that the product glass would meet federal repository acceptance requirements. The system was built and performed to standards which would have enabled it to be used in radioactive service. As a result, much of the VF tested, such as the civil construction, feed mixing and holding vessels, and the off-gas scrubber, will be converted for radioactive operation. The melter was still in good condition after being at temperature for fifty-eight of the sixty months of FACTS. However, the melter exceeded its recommended design life and will be replaced with a similar melter. Components that were not designed for remote operation and maintenance will be replaced with remote-use items. The FACTS testing was accomplished with no significant worker injury or environmental releases. During the last FACTS run, the VF processes approximated the remote-handling system that will be used in radioactive operations. Following this run the VF was disassembled for conversion to a radioactive process. Functional and checkout testing of new components will be performed prior to radioactive operation.

  8. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1997-06-30

    The Liquid Phase Methanol (LPMEOHTM) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOIYM Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this quarter, comments from the DOE on the Topical Report "Economic Analysis - LPMEOHTM Process as an Add-on to IGCC for Coproduction" were received. A recommendation to continue with design verification testing for the coproduction of dimethyl ether (DIME) and methanol was made. DME design verification testing studies show the liquid phase DME (LPDME) process will have a significant economic advantage for the coproduction of DME for local markets. An LPDME catalyst system with reasonable long-term activity and stability is being developed. A recommendation document summarizing catalyst targets, experimental results, and the corresponding economics for a commercially successful LPDME catalyst was issued on 30 June 1997. The off-site, product-use test plan was updated in June of 1997. During this quarter, Acurex Environmental Corporation and Air Products screened proposals for this task by the likelihood of the projects to proceed and the timing for the initial methanol requirement. Eight sites from the list have met these criteria. The formal submission of the eight projects for review and concurrence by the DOE will be made during the next reporting period. The site paving and final painting were completed in May of 1997. Start-up activities were completed during the reporting period, and the initial methanol production from the demonstration unit occurred on 02 April 1997. The first extended stable operation at the nameplate capacity of 80,000 gallons per day (260 tons

  9. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1997-06-30

    The Liquid Phase Methanol (LPMEOHTM) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOIYM Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this quarter, comments from the DOE on the Topical Report "Economic Analysis - LPMEOHTM Process as an Add-on to IGCC for Coproduction" were received. A recommendation to continue with design verification testing for the coproduction of dimethyl ether (DIME) and methanol was made. DME design verification testing studies show the liquid phase DME (LPDME) process will have a significant economic advantage for the coproduction of DME for local markets. An LPDME catalyst system with reasonable long-term activity and stability is being developed. A recommendation document summarizing catalyst targets, experimental results, and the corresponding economics for a commercially successful LPDME catalyst was issued on 30 June 1997. The off-site, product-use test plan was updated in June of 1997. During this quarter, Acurex Environmental Corporation and Air Products screened proposals for this task by the likelihood of the projects to proceed and the timing for the initial methanol requirement. Eight sites from the list have met these criteria. The formal submission of the eight projects for review and concurrence by the DOE will be made during the next reporting period. The site paving and final painting were completed in May of 1997. Start-up activities were completed during the reporting period, and the initial methanol production from the demonstration unit occurred on 02 April 1997. The first extended stable operation at the nameplate capacity of 80,000 gallons per day (260 tons

  10. Warm Cleanup of Coal-Derived Syngas: Multicontaminant Removal Process Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Spies, Kurt A.; Rainbolt, James E.; Li, Xiaohong S.; Braunberger, Beau; Li, Liyu; King, David L.; Dagle, Robert A.

    2017-02-15

    Warm cleanup of coal- or biomass-derived syngas requires sorbent and catalytic beds to protect downstream processes and catalysts from fouling. Sulfur is particularly harmful because even parts-per-million amounts are sufficient to poison downstream synthesis catalysts. Zinc oxide (ZnO) is a conventional sorbent for sulfur removal; however, its operational performance using real gasifier-derived syngas and in an integrated warm cleanup process is not well reported. In this paper, we report the optimal temperature for bulk desulfurization to be 450oC, while removal of sulfur to parts-per-billion levels requires a lower temperature of approximately 350oC. Under these conditions, we found that sulfur in the form of both hydrogen sulfide and carbonyl sulfide could be absorbed equally well using ZnO. For long-term operation, sorbent regeneration is desirable to minimize process costs. Over the course of five sulfidation and regeneration cycles, a ZnO bed lost about a third of its initial sulfur capacity, however sorbent capacity stabilized. Here, we also demonstrate, at the bench-scale, a process and materials used for warm cleanup of coal-derived syngas using five operations: 1) Na2CO3 for HCl removal, 2) regenerable ZnO beds for bulk sulfur removal, 3) a second ZnO bed for trace sulfur removal, 4) a Ni-Cu/C sorbent for multi-contaminant inorganic removal, and 5) a Ir-Ni/MgAl2O4 catalyst employed for ammonia decomposition and tar and light hydrocarbon steam reforming. Syngas cleanup was demonstrated through successful long-term performance of a poison-sensitive, Cu-based, water-gas-shift catalyst placed downstream of the cleanup process train. The tar reformer is an important and necessary operation with this particular gasification system; its inclusion was the difference between deactivating the water-gas catalyst with carbon deposition and successful 100-hour testing using 1 LPM of coal-derived syngas.

  11. Lab-scale demonstration of the UREX+1a process using spent nuclear fuel.

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, C.; Vandegrift, G. F.; Regalbuto, M. C.; Bakel, A.; Bowers, D.; Gelia, A. V.; Hebden, A. S.; Maggos, L. E.; Stepinski, D.; Tsai, Y.; Laidler, J. J.; Chemical Engineering

    2007-01-01

    The Global Nuclear Energy Partnership (GNEP) is developing technologies to greatly expand repository capacity, improve proliferation resistance, and recover valuable energy that would otherwise be discarded; thus assuring a stable energy supply for the future. An important element of this initiative is the separation of key radionuclides followed by either superior waste-disposal forms and/or transmutation of long-lived isotopes. To that end, the GNEP is developing advanced fuel reprocessing systems that separate key radionuclides from spent fuel. One of these systems is the UREX+1a process. The UREX+1a process is a series of four solvent-extraction flowsheets that perform the following operations: (1) recovery of U and Tc (UREX), (2) recovery of Cs and Sr (CCD-PEG), and (3) recovery of TRU and rare earth elements (TRUEX), and (4) separation of TRU elements from the rare earths (TALSPEAK). This paper discusses the results of the demonstration of the UREX, TRUEX, and TALSPEAK processes using spent nuclear fuel, as well as future development needs and plans.

  12. CSPonD demonstrative project: Start-up process of a 25 kW prototype

    Science.gov (United States)

    Gil, Antoni; Grange, Benjamin; Perez, Victor G.; Tetreault-Friend, Melanie; Codd, Daniel S.; Calvet, Nicolas; Slocum, Alexander S.

    2017-06-01

    The current concept of commercial concentrated solar power (CSP) plants, based on the concept of a solar field, receiver, storage and power block, experienced significant growth in the past decades. The power block is the most well know part of the plant, while solar field depends on the receiver technology. The dominant receiver technologies are parabolic troughs and central towers. Most thermal energy storage (TES) relies on two tanks of molten salts, one hot and one cold serviced by pumps and piping systems. In spite of the technical development level achieved by these systems, efficiency is limited, mainly caused by thermal losses in piping, parasitic losses due to electric tracing and pumping and receiver limitations. In order to mitigate the these issues, a new concept called Concentrated Solar Power on Demand (CSPonD), was developed, consisting of a direct absorption Solar Salt CSP receiver which simultaneously acts as TES tank. Currently, in the frame of the flagship collaborative project between the Masdar Institute (UAE) and the Massachusetts Institute of Technology (USA) a 25 kW demonstrative prototype is in its final building phase at the Masdar Institute Solar Platform. The present paper, explains the demonstration prototype based on the CSPonD concept, with emphasis on the planned start-up process for the facility.

  13. Functional MRI demonstrates pain perception in hand osteoarthritis has features of central pain processing.

    Science.gov (United States)

    Sofat, Nidhi; Smee, Cori; Hermansson, Monika; Howard, Matthew; Baker, Emma H; Howe, Franklyn A; Barrick, Thomas R

    2013-11-01

    Hand osteoarthritis (HOA) is typified by pain and reduced function. We hypothesised that people with HOA have enhanced sensitivity and activation of peripheral nociceptors in the hand, thereby potentiating chronic pain. In our study we aimed to assess if central sensitisation mediates pain perception in osteoarthritis of the hand. Participants with proximal and distal interphalangeal joint (PIP/DIP) HOA and non-OA controls were recruited. Clinical pain scores using the visual analogue scale (VAS) were recorded before and after performing a painful hand task. Central pain processing was evaluated with functional brain neuroimaging (fMRI) using a finger flexion-extension (FFE) task performed over 3 minutes. Data was analysed with FMRIB software (www.fmrib.ox.ac.uk/fsl). Group mean activation of functional MRI signal between hand osteoarthritis and control non-arthritic participants was compared. Our group of hand OA participants reported high pain levels compared with non-arthritic controls as demonstrated by the mean VAS in hand OA participants of 59.31± 8.19 mm compared to 4.00 ± 1.89 mm in controls (p central sensitisation. People with hand osteoarthritis demonstrated features of central sensitisation that was evident after a finger flexion-extension task using functional MRI. Functional MRI is a useful biomarker in detecting pain in hand osteoarthritis and could be used in future hand osteoarthritis pain studies to evaluate pain modulation strategies.

  14. Data acquisition and processing in the ATLAS Tile Calorimeter Phase-II Upgrade Demonstrator

    CERN Document Server

    Valero, Alberto; The ATLAS collaboration

    2016-01-01

    The LHC has planned a series of upgrades culminating in the High Luminosity LHC (HL-LHC) which will have an average luminosity 5-7 times larger than the nominal Run-2 value. The ATLAS Tile Calorimeter (TileCal) will undergo an upgrade to accommodate to the HL-LHC parameters. The TileCal read-out electronics will be redesigned introducing a new read-out strategy. The photomultiplier signals will be digitized and transferred to the TileCal PreProcessors (TilePPr) located off-detector for every bunch crossing, requiring a data bandwidth of 80 Tbps. The TilePPr will provide preprocessed information to the first level of trigger and in parallel will store the samples in pipeline memories. The data of the events selected by the trigger system will be transferred to the ATLAS global Data AcQuisition (DAQ) system for further processing. A demonstrator drawer has been built to evaluate the new proposed readout architecture and prototypes of all the components. In the demonstrator, the detector data received in the Til...

  15. Wet autoclave pretreatment for immunohistochemical demonstration of oestrogen receptors in routinely processed breast carcinoma tissue.

    Science.gov (United States)

    Bier, B; Bankfalvi, A; Grote, L; Blasius, S; Ofner, D; Böcker, W; Jasani, B; Schmid, K W

    1995-02-01

    The immunohistochemical demonstration of oestrogen receptor (OR) was performed on 32 randomly selected and routinely processed breast carcinomas after wet autoclave pretreatment of sections. The autoclave method was compared to the OR status found on frozen sections as well as to alternative pretreatment methods such as enzymatic predigestion and microwave irradiation. Using four different monoclonal antibody clones (H222, LH1, CC4-5, 1D5.26), the OR status was evaluated for each of the various pretreatment methods applied. All cases with a high OR content on frozen sections (n = 11) also showed a high OR status on wet autoclave-pretreated paraffin tissues using antibody clones 1D5.26 and CC4-5; in cases with low OR content on frozen sections, no false-negative cases were recorded using only the antibody 1D5.26 neither after wet autoclave nor microwave pretreatment. In addition, with this antibody, OR was detectable after autoclave pretreatment in two cases which were considered to be OR-negative even on frozen sections. When the primary antibody was omitted, no false-positive cases were observed after wet autoclave pretreatment. Thus, in our hands, wet autoclave pretreatment, in combination with the antibody 1D5.26, offers a highly sensitive method for the immunohistochemical demonstration of OR in routinely formalin-fixed, paraffin-embedded sections of breast carcinomas.

  16. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1998-12-21

    The Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOW Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this quarter, initial planning and procurement work began on the seven project sites which have been accepted for participation in the off-site, methanol product-use test plan. Two of the projects have begun pre-testing of equipment and three other projects have commenced with equipment procurement, Methanol produced from carbon monoxide (CO)- rich syngas at the Alternative Fuels Development Unit (AFDU) in LaPorte, TX has been shipped to four of the project sites in anticipation of the start of testing during the first quarter of calendar year 1998. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for a freshly reduced catalyst (as determined in the laboratory autoclave), continued to decline more rapidly than expected. In response to concentrations of arsenic and sulfbr detected on catalyst samples from the LPMEOW Reactor, Eastman replaced both the arsine- and sulfiwremoval material in the Eastman guard bed which treats the primary syngas feed stream (&danced Gas) prior to its introduction into both the Eastman fixed-bed methanol plant and the LPMEOWM Demonstration Unit. After restarting the demonstration unit, the catalyst deactivation rate remained essentially unchanged. Parallel testing in the laboratory using arsine-doped, and subsequently arsine- and SuIfi-doped syngas, ako ftiIed to prove that arsine was responsible for the higher-than-expected rate of

  17. Synthetic-aperture imaging laser radar: laboratory demonstration and signal processing.

    Science.gov (United States)

    Beck, Steven M; Buck, Joseph R; Buell, Walter F; Dickinson, Richard P; Kozlowski, David A; Marechal, Nicholas J; Wright, Timothy J

    2005-12-10

    The spatial resolution of a conventional imaging laser radar system is constrained by the diffraction limit of the telescope's aperture. We investigate a technique known as synthetic-aperture imaging laser radar (SAIL), which employs aperture synthesis with coherent laser radar to overcome the diffraction limit and achieve fine-resolution, long-range, two-dimensional imaging with modest aperture diameters. We detail our laboratory-scale SAIL testbed, digital signal-processing techniques, and image results. In particular, we report what we believe to be the first optical synthetic-aperture image of a fixed, diffusely scattering target with a moving aperture. A number of fine-resolution, well-focused SAIL images are shown, including both retroreflecting and diffuse scattering targets, with a comparison of resolution between real-aperture imaging and synthetic-aperture imaging. A general digital signal-processing solution to the laser waveform instability problem is described and demonstrated, involving both new algorithms and hardware elements. These algorithms are primarily data driven, without a priori knowledge of waveform and sensor position, representing a crucial step in developing a robust imaging system.

  18. A Demonstrator Analog Signal Processing Circuit in a Radiation Hard SOI-CMOS Technology

    CERN Multimedia

    2002-01-01

    % RD-9 A Demonstrator Analog Signal Processing Circuit in a Radiation Hard SOI-CMOS Technology \\\\ \\\\Radiation hardened SOI-CMOS (Silicon-On-Insulator, Complementary Metal-Oxide- \\linebreak Semiconductor planar microelectronic circuit technology) was a likely candidate technology for mixed analog-digital signal processing electronics in experiments at the future high luminosity hadron colliders. We have studied the analog characteristics of circuit designs realized in the Thomson TCS radiation hard technologies HSOI3-HD. The feature size of this technology was 1.2 $\\mu$m. We have irradiated several devices up to 25~Mrad and 3.10$^{14}$ neutrons cm$^{-2}$. Gain, noise characteristics and speed have been measured. Irradiation introduces a degradation which in the interesting bandwidth of 0.01~MHz~-~1~MHz is less than 40\\%. \\\\ \\\\Some specific SOI phenomena have been studied in detail, like the influence on the noise spectrum of series resistence in the thin silicon film that constitutes the body of the transistor...

  19. Demonstration of the waste tire pyrolysis process on pilot scale in a continuous auger reactor

    Energy Technology Data Exchange (ETDEWEB)

    Martínez, Juan Daniel, E-mail: juand.martinez@upb.edu.co [Instituto de Carboquímica, ICB-CSIC, Miguel Luesma Castán 4, 50018, Zaragoza (Spain); Grupo de Investigaciones Ambientales, Instituto de Energía, Materiales y Medio Ambiente, Universidad Pontificia Bolivariana, Circular 1 N°70-01, Bloque 11, piso 2, Medellín (Colombia); Murillo, Ramón; García, Tomás; Veses, Alberto [Instituto de Carboquímica, ICB-CSIC, Miguel Luesma Castán 4, 50018, Zaragoza (Spain)

    2013-10-15

    Highlights: • The continuous pyrolysis of waste tire has been demonstrated at pilot scale in an auger reactor. • More than 500 kg of waste tires were processed in 100 operational hours. • The yields and characteristics of the pyrolysis products remained constant. • Mass and energy balances for an industrial scale plant are provided. • The reaction enthalpy necessary to perform the waste tire pyrolysis was determined. -- Abstract: This work shows the technical feasibility for valorizing waste tires by pyrolysis using a pilot scale facility with a nominal capacity of 150 kW{sub th}. A continuous auger reactor was operated to perform thirteen independent experiments that conducted to the processing of more than 500 kg of shredded waste tires in 100 h of operation. The reaction temperature was 550 °C and the pressure was 1 bar in all the runs. Under these conditions, yields to solid, liquid and gas were 40.5 ± 0.3, 42.6 ± 0.1 and 16.9 ± 0.3 wt.% respectively. Ultimate and proximate analyses as well as heating value analysis were conducted for both the solid and liquid fraction. pH, water content, total acid number (TAN), viscosity and density were also assessed for the liquid and compared to the specifications of marine fuels (standard ISO 8217). Gas chromatography was used to calculate the composition of the gaseous fraction. It was observed that all these properties remained practically invariable along the experiments without any significant technical problem. In addition, the reaction enthalpy necessary to perform the waste tire pyrolysis process (907.1 ± 40.0 kJ/kg) was determined from the combustion and formation enthalpies of waste tire and conversion products. Finally, a mass balance closure was performed showing an excellent reliability of the data obtained from the experimental campaign.

  20. Uniform transport performance of a 100 m-class multifilament MgB2 wire fabricated by an internal Mg diffusion process

    Science.gov (United States)

    Wang, Dongliang; Xu, Da; Zhang, Xianping; Yao, Chao; Yuan, Pusheng; Ma, Yanwei; Oguro, Hidetoshi; Awaji, Satoshi; Watanabe, Kazuo

    2016-06-01

    A 100 m long six-filament MgB2 wire was successfully fabricated using an internal magnesium diffusion (IMD) process. We investigated the transport properties and the uniformity of this long multifilament IMD wire. The MgB2 layer and the sub-filament region are regular, and the J c values have a fairly homogenous distribution throughout the wire, suggesting that there were no obvious defects along the length of the wire. The uniformity problem of long multifilament IMD MgB2 wires can be mitigated by optimizing the starting composite parameters, multifilament geometry, fabricating process and annealing conditions. A layer J c as high as 1.2 × 105 A cm-2 at 4.2 K and 8 T was obtained, which was comparable with the highest reported value for a short multifilament IMD wire. The transport layer J c, non-barrier J c and J e values are independent of the wire diameter. In addition, the analysis of the stress-strain characteristics and the n value of the IMD wire is also presented. These results indicate that the long multifilament IMD-processed MgB2 superconducting wire is suitable for practical applications.

  1. Uniform Requirements for Manuscripts

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    @@ Introduction The Uniform requirements are instructions to authors on how to prepare manuscripts.If authors prepare their manuscripts in the style specified in these requirements, editors of the participating journals will not return the manuscripts for changes in style before considering them for publication.In the publishing process, however, the journals may alter accepted manuscripts to conform with details of their publication styles.

  2. Novel bacterial consortia isolated from plastic garbage processing areas demonstrated enhanced degradation for low density polyethylene.

    Science.gov (United States)

    Skariyachan, Sinosh; Manjunatha, Vishal; Sultana, Subiya; Jois, Chandana; Bai, Vidya; Vasist, Kiran S

    2016-09-01

    This study aimed to formulate novel microbial consortia isolated from plastic garbage processing areas and thereby devise an eco-friendly approach for enhanced degradation of low-density polyethylene (LDPE). The LDPE degrading bacteria were screened and microbiologically characterized. The best isolates were formulated as bacterial consortia, and degradation efficiency was compared with the consortia formulated using known isolates obtained from the Microbial Culture Collection Centre (MTCC). The degradation products were analyzed by FTIR, GC-FID, tensile strength, and SEM. The bacterial consortia were characterized by 16S ribosomal DNA (rDNA) sequencing. The formulated bacterial consortia demonstrated 81 ± 4 and 38 ± 3 % of weight reduction for LDPE strips and LDPE pellets, respectively, over a period of 120 days. However, the consortia formulated by MTCC strains demonstrated 49 ± 4 and 20 ± 2 % of weight reduction for LDPE strips and pellets, respectively, for the same period. Furthermore, the three isolates in its individual application exhibited 70 ± 4, 68 ± 4, and 64 ± 4 % weight reduction for LDPE strips and 21 ± 2, 28 ± 2, 24 ± 2 % weight reduction for LDPE pellets over a period of 120 days (p product analysis showed structural changes and formation of bacterial film on degraded LDPE strips. The 16S rDNA characterization of bacterial consortia revealed that these organisms were novel strains and designated as Enterobacter sp. bengaluru-btdsce01, Enterobacter sp. bengaluru-btdsce02, and Pantoea sp. bengaluru-btdsce03. The current study thus suggests that industrial scale-up of these microbial consortia probably provides better insights for waste management of LDPE and similar types of plastic garbage.

  3. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH) Process

    Energy Technology Data Exchange (ETDEWEB)

    None

    1998-12-21

    he Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOEP Process Demonstration Unit was built at a site located at the Eastman coal-to-chemicals complex in Kingsport. The LPMEOHW Demonstration Facility completed its first year of operation on 02 April 1998. The LPMEOW Demonstration Facility also completed the longest continuous operating run (65 days) on 21 April 1998. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for freshly reduced catalyst (as determined in the laboratory autoclave), was monitored throughout the reporting period. During a six-week test at a reactor temperature of 225oC and Balanced Gas flowrate of 700 KSCFH, the rate of decline in catalyst activity was steady at 0.29-0.36% per day. During a second one-month test at a reactor temperature of 220oC and a Balanced Gas flowrate of 550-600 KSCFH, the rate of decline in catalyst activity was 0.4% per day, which matched the pefiorrnance at 225"C, as well as the 4-month proof-of-concept run at the LaPorte AFDU in 1988/89. Beginning on 08 May 1998, the LPMEOW Reactor temperature was increased to 235oC, which was the operating temperature tier the December 1997 restart with the fresh charge of catalyst (50'Yo of design loading). The flowrate of the primary syngas feed stream (Balanced Gas) was also increased to 700-750 KSCFH. During two stable operating periods between 08 May and 09 June 1998, the average catalyst deactivation rate was 0.8% per day. Due to the scatter of the statistical analysis of the results, this test was extended to better

  4. Web services-based text-mining demonstrates broad impacts for interoperability and process simplification.

    Science.gov (United States)

    Wiegers, Thomas C; Davis, Allan Peter; Mattingly, Carolyn J

    2014-01-01

    The Critical Assessment of Information Extraction systems in Biology (BioCreAtIvE) challenge evaluation tasks collectively represent a community-wide effort to evaluate a variety of text-mining and information extraction systems applied to the biological domain. The BioCreative IV Workshop included five independent subject areas, including Track 3, which focused on named-entity recognition (NER) for the Comparative Toxicogenomics Database (CTD; http://ctdbase.org). Previously, CTD had organized document ranking and NER-related tasks for the BioCreative Workshop 2012; a key finding of that effort was that interoperability and integration complexity were major impediments to the direct application of the systems to CTD's text-mining pipeline. This underscored a prevailing problem with software integration efforts. Major interoperability-related issues included lack of process modularity, operating system incompatibility, tool configuration complexity and lack of standardization of high-level inter-process communications. One approach to potentially mitigate interoperability and general integration issues is the use of Web services to abstract implementation details; rather than integrating NER tools directly, HTTP-based calls from CTD's asynchronous, batch-oriented text-mining pipeline could be made to remote NER Web services for recognition of specific biological terms using BioC (an emerging family of XML formats) for inter-process communications. To test this concept, participating groups developed Representational State Transfer /BioC-compliant Web services tailored to CTD's NER requirements. Participants were provided with a comprehensive set of training materials. CTD evaluated results obtained from the remote Web service-based URLs against a test data set of 510 manually curated scientific articles. Twelve groups participated in the challenge. Recall, precision, balanced F-scores and response times were calculated. Top balanced F-scores for gene, chemical and

  5. Ensuring Program Uniformity at the Hearing and Appeals Council Levels of the Administrative Review Process. Final rule.

    Science.gov (United States)

    2016-12-16

    We are revising our rules so that more of our procedures at the hearing and Appeals Council levels of our administrative review process are consistent nationwide. We anticipate that these nationally consistent procedures will enable us to administer our disability programs more efficiently and better serve the public.

  6. Exact solutions of linear reaction-diffusion processes on a uniformly growing domain: criteria for successful colonization.

    Directory of Open Access Journals (Sweden)

    Matthew J Simpson

    Full Text Available Many processes during embryonic development involve transport and reaction of molecules, or transport and proliferation of cells, within growing tissues. Mathematical models of such processes usually take the form of a reaction-diffusion partial differential equation (PDE on a growing domain. Previous analyses of such models have mainly involved solving the PDEs numerically. Here, we present a framework for calculating the exact solution of a linear reaction-diffusion PDE on a growing domain. We derive an exact solution for a general class of one-dimensional linear reaction-diffusion process on 0

  7. Improved electron transportation of dye-sensitized solar cells using uniform mixed CNTs-TiO{sub 2} photoanode prepared by a new polymeric gel process

    Energy Technology Data Exchange (ETDEWEB)

    Bakhshayesh, A. M.; Mohammadi, M. R., E-mail: mrm41@cam.ac.uk; Masihi, N.; Akhlaghi, M. H. [Sharif University of Technology, Department of Materials Science and Engineering (Iran, Islamic Republic of)

    2013-09-15

    A new facile strategy for fabrication of high surface area electrode in the form of mixtures of coated carbon nanotubes (CNTs) and TiO{sub 2} nanoparticles with various weight ratios is reported. The so-called polymeric gel process was used to deposit thick film containing uniform distribution of TiO{sub 2} nanoparticles and coated CNTs with high porosity by dip coating for dye-sensitized solar cells (DSSCs) applications. Based on simultaneous differential thermal analysis, the minimum annealing temperature to obtain inorganic- and organic-free films was determined at 500 Degree-Sign C. X-ray diffraction analysis revealed that deposited films were composed of primary nanoparticles with crystallite size in the range 21-45 nm. Field emission scanning electron microscope images showed that deposited films had porous morphology containing uniform spherical particles with diameter around 2.5 {mu}m and coated CNTs with TiO{sub 2} nanoparticles (TNTs). The spherical particles were composed of small nanoparticles ({approx}60 nm), improving light scattering and dye loading of the DSSC. Moreover, TNTs were uniformly incorporated into the electrodes, improving electron transportation. X-ray photoelectron spectroscopy was presented as an obvious proof for the inclusion of CNTs into the TiO{sub 2} matrix. Ultraviolet-visible spectroscopy showed that CNT introduction enhanced the visible light absorption of photoanode by shifting the absorption onset to visible light region. An enhancement of power conversion efficiency (PCE) from 6.53 % for pure TiO{sub 2} to 7.38 % for CNT-TiO{sub 2} electrode containing 0.025 wt% CNTs was achieved. This well-incorporated study would present an intellectual development in the fabrication of low-cost CNT consolidated DSSCs with high PCE.

  8. Development and demonstration of calculation tool for industrial drying processes ''DryPack''; Udvikling og demonstration af beregningsvaerktoej til industrielle toerreprocesser ''DryPack''

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, P.; Weinkauff Kristoffersen, J.; Blazniak Andreasen, M. [Teknologisk Institut, Aarhus (Denmark); Elmegaard, B.; Kaern, M. [Danmarks Tekniske Univ.. DTU Mekanik, Kgs. Lyngby (Denmark); Monrad Andersen, C. [Lokal Energi, Viby J. (Denmark); Grony, K. [SE Big Blue, Kolding (Denmark); Stihoej, A. [Enervision, Kolding (Denmark)

    2013-03-15

    In this project we have developed a calculation tool for calculating energy consumption in different drying processes - primarily drying processes with air. The program can be used to determine the energy consumption of a current drying process, after which it can be calculated how much energy can be saved by various measures. There is also developed a tool for the simulation of a batch drier, which calculates the drying of a batch depending on the time. The programs have demonstrated their usefulness in connection with three cases that are reviewed in the report. In the project measurements on four different dryers have been carried out, and energy consumption is calculated using ''DryPack''. With ''DryPack'' it is possible to find potential savings by optimizing the drying processes. The program package includes utilities for the calculation of moist air: 1) Calculation of the thermodynamic properties of moist air; 2) Device operation with moist air (mixing, heating, cooling and humidification); 3) Calculation of the relative change of the drying time by changing the process parameters; 4) IX-diagram at a temperature above 100 deg. C. (LN)

  9. Effects of fixation and tissue processing on immunohistochemical demonstration of specific antigens.

    Science.gov (United States)

    Arnold, M M; Srivastava, S; Fredenburgh, J; Stockard, C R; Myers, R B; Grizzle, W E

    1996-09-01

    Identification of biomarkers in archival tissues using immunochemistry is becoming increasingly important for determining the diagnosis and prognosis of tumors, for characterizing preinvasive neoplastic changes in glandular tissues such as prostate, for evaluating the response of tumors and preinvasive neoplastic changes to certain therapies (i.e., as a surrogate intermediate end point), for selecting patients who are candidates for specific therapies (e.g., immunotherapy) and for retrospective studies. For detecting specific biomarkers it is important to understand the limitations imposed by the fixation methods and processing of the tissues. This study was designed to determine the effects of fixation on the detection in archival paraffin blocks of selected antigens postulated to be important in tumor biology. We evaluated the antigens TGF alpha, p185erbB-2, broad spectrum keratins, p53, and TAG-72 (B72.3). Fixatives evaluated included standard preparations of neutral buffered formalin, acid formalin, zinc formalin, alcoholic formalin, ethanol, methanol, and Bouin's fixative. We found that in general neutral buffered formalin is the poorest fixative for maintaining antigen recognition by immunohistochemistry and that no single fixative was best for all antigens. The dehydrating (coagulant) fixatives (e.g., ethanol and methanol) preserved immunorecognition of p53 and broad spectrum keratins best while the slow cross-linking fixatives (e.g., unbuffered zinc formalin) were best for demonstrating TGF alpha and p185erbB-2. Fixatives other than neutral buffered formalin produced equivalent recognition of the epitope of TAG-72 by B72.3. In formalin fixed archival tissues, only a portion of the antigen signal can be detected by routine immunohistologic methods.

  10. A non-uniformly sampled 4D HCC(CO)NH-TOCSY experiment processed using maximum entropy for rapid protein sidechain assignment

    Science.gov (United States)

    Mobli, Mehdi; Stern, Alan S.; Bermel, Wolfgang; King, Glenn F.; Hoch, Jeffrey C.

    2010-05-01

    One of the stiffest challenges in structural studies of proteins using NMR is the assignment of sidechain resonances. Typically, a panel of lengthy 3D experiments are acquired in order to establish connectivities and resolve ambiguities due to overlap. We demonstrate that these experiments can be replaced by a single 4D experiment that is time-efficient, yields excellent resolution, and captures unique carbon-proton connectivity information. The approach is made practical by the use of non-uniform sampling in the three indirect time dimensions and maximum entropy reconstruction of the corresponding 3D frequency spectrum. This 4D method will facilitate automated resonance assignment procedures and it should be particularly beneficial for increasing throughput in NMR-based structural genomics initiatives.

  11. Demonstrating an Interactive Genetic Drift Exercise: Examining the Processes of Random Mating and Selection.

    Science.gov (United States)

    Carter, Ashley J. R.

    2002-01-01

    Presents a hands-on activity on the phenomenon of genetic drift in populations that reinforces the random nature of drift and demonstrates the effect of the population size on the mean frequency of an allele over a few generations. Includes materials for the demonstration, procedures, and discussion topics. (KHR)

  12. The Manufacturing Process for the NASA Composite Crew Module Demonstration Structure

    Science.gov (United States)

    Pelham, Larry; Higgins, John E.

    2008-01-01

    lower tooling cost and less manufacturing risk. Assembly of the top and bottom halves of the pressure shell will allow access to the interior of the shell throughout remaining fabrication sequence and can also potentially permit extensive installation of equipment and .crew facilities prior to final assembly of the two shell halves. A Pi pre-form is a woven carbon composite material which is provided in pre-impregnated form and frozen for long term storage. The cross-section shape allows the top of the pi to be bonded to a flat or curved surface with a second flat plate composite section bonded between two upstanding legs of the Pi. One of the regions relying on the merits of the Pi pre-form is the backbone. All connections among plates of the backbone structure, including the upper flanges, and to the lobe base of the pressure shell are currently joined by Pi pre-forms. The intersection of backbone composite plates is formed by application of two Pi pre-forms, top flanges and lobed surfaces are bonded with one Pi pre-form. The process of applying the pre-impregnated pi-preform will be demonstrated to include important steps like surface preparation, forming, application of pressure dams, vacuum bagging for consolidation, and curing techniques. Chopped carbon fiber tooling was selected over other traditional metallic and carbon fiber tooling. The requirement of schedule and cost economy for a moderate reuse cure tool warranted composite tooling options. Composite tooling schedule duration of 18 weeks compared favorably against other metallic tooling including invar tooling. Composite tooling also shows significant cost savings over low CTE metallic options. The composite tooling options were divided into two groups and the final decision was based on the cost, schedule, tolerance, temperature, and reuse requirements.

  13. Analysis of Monolith Cores from an Engineering Scale Demonstration of a Prospective Cast Stone Process

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States); Hill, K. A. [Savannah River Site (SRS), Aiken, SC (United States)

    2016-06-01

    The primary disposition path of Low Activity Waste (LAW) at the DOE Hanford Site is vitrification. A cementitious waste form is one of the alternatives being considered for the supplemental immobilization of the LAW that will not be treated by the primary vitrification facility. Washington River Protection Solutions (WRPS) has been directed to generate and collect data on cementitious or pozzolanic waste forms such as Cast Stone. This report documents the coring and leach testing of monolithic samples cored from an engineering-scale demonstration (ES Demo) with non-radioactive simulants. The ES Demo was performed at SRNL in October of 2013 using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft. diameter x 3.25 ft. high container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average LAW composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. In 2014 core samples originally obtained approximately six months after filling the ES Demo were tested along with bench scale molded samples that were collected during the original pour. A latter set of core samples were obtained in late March of 2015, eighteen months after completion of the original ES Demo. Core samples were obtained using a 2” diameter x 11” long coring bit. The ES Demo was sampled in three different regions consisting of an outer ring, a middle ring and an inner core zone. Cores from these three lateral zones were further segregated into upper, middle and lower vertical segments. Monolithic core samples were tested using the Environmental Protection Agency (EPA) Method 1315, which is designed to provide mass transfer rates

  14. Small-scale demonstration of high-level radioactive waste processing and solidification using actual SRP waste

    Energy Technology Data Exchange (ETDEWEB)

    Okeson, J K; Galloway, R M; Wilhite, E L; Woolsey, G B; B, Ferguson R

    1980-01-01

    A small-scale demonstration of the high-level radioactive waste solidification process by vitrification in borosilicate glass is being conducted using 5-6 liter batches of actual waste. Equipment performance and processing characteristics of the various unit operations in the process are reported and, where appropriate, are compared to large-scale results obtained with synthetic waste.

  15. 75 FR 56946 - Medicaid Program; Review and Approval Process for Section 1115 Demonstrations

    Science.gov (United States)

    2010-09-17

    ... criteria: Quantitative Research Methods: Quantitative.... In proposed Sec. 431.408(a)(2)(i), we have expanded the methods for States to provide public notice... the State believes to be necessary to authorize the demonstration. The research hypothesis or...

  16. High-Yield Synthesis of Uniform Ag Nanowires with High Aspect Ratios by Introducing the Long-Chain PVP in an Improved Polyol Process

    Directory of Open Access Journals (Sweden)

    Jie-Jun Zhu

    2011-01-01

    Full Text Available Polyvinyl pyrrolidone (PVP with different molecular weights was used as capping agent to synthesize silver nanowires through a polyol process. The results indicated that the yields and aspect ratios of silver nanowires were controlled by the chain length of PVP and increased with increasing the molecular weight (MW of PVP. When the long-chain PVP-K90 (MW = 800,000 was used, the product was uniform in size and was dominated by nanowires with high aspect ratios. The growth mechanism of the nanowires was studied. It is proposed that the chemical adsorption of Ag+ on the PVP chains at the initial stage promotes the growth of Ag nanowires.

  17. A process for ensuring regulatory compliance at the INEL`s buried waste integrated demonstrations

    Energy Technology Data Exchange (ETDEWEB)

    Cannon, P.G.; Watson, L.R.; Blacker, P.B. [EG and G Idaho, Inc., Idaho Falls, ID (United States). Idaho National Engineering Lab.

    1993-03-01

    The Buried Waste Integrated Demonstration Program is funded by the Department of Energy Office of Technology Development. The mission of this Integrated Demonstration is to identify, evaluate, and demonstrate a suite of innovative technologies for the remediation of radioactive and hazardous waste buried throughout the DOE complex between 1950 and 1970. The program approach to development of a long-range strategy for improving buried waste remediation capabilities is to combine systems analysis with already identified remediation needs for DOE complex buried waste. The systems analysis effort has produced several configuration options (a top-level block diagram of a cradle-to-grave remediation system) capable of remediating the transuranic-contaminated waste pits and trenches at the Idaho National Engineering Laboratory. Technologies for demonstration are selected using three criteria: (a) the ability to satisfy a specific buried waste need, (b) the ability to satisfy functional and operational requirements defined for functional sub-elements in a configuration option, and (c) performance against Comprehensive Environmental Restoration and Compensation Liability Act selection criteria, such as effectiveness, implementability, and cost. Early demonstrations experienced problems with missed requirements, prompting the Buried Waste Integrated Demonstration Program Office to organize a Corrective Action Team to identify the cause and recommend corrective actions. The result of this team effort is the focus of this paper.

  18. Uniform sampling table method and its applications: establishment of a uniform sampling method.

    Science.gov (United States)

    Chen, Yibin; Chen, Jiaxi; Wang, Wei

    2013-01-01

    A novel uniform sampling method is proposed in this paper. According to the requirements of uniform sampling, we propose the properties that must be met by analyzing the distribution of samples. Based on this, the proposed uniform sampling method is demonstrated and evaluated strictly by mathematical means such as inference. The uniform sampling tables with respect to Cn(t2) and Cn(t3) are established. Furthermore, a one-dimension uniform sampling method and a multidimension method are proposed. The proposed novel uniform sampling method, which is guided by uniform design theory, enjoys the advantages of simplified use and good representativeness of the whole sample.

  19. An Experimental and Mathematical Study to Evaluate the Role of Ultrasonic Energy in Promoting Microstructural Uniformity During Controlled Directional Solidification Processing

    Science.gov (United States)

    Grugel, R. N.; Fedoseyev, A. I.; Rose, M. Franklin (Technical Monitor)

    2000-01-01

    There are many commercially relevant metal and non-metal "alloy" systems that separate into two different liquids upon cooling from a higher temperature. Consequently during solidification processing the inherent density differences between the two liquid phases leads to rapid, gravity driven, separation and severe segregation, a factor that significantly compromises the desired material properties. Processing in a microgravity environment minimizes settling but segregation still occurs due to gravity independent wetting and coalescence phenomena. This presentation reports on experiments that utilized succinonitrile-glycerol mixtures, a transparent system that 1) separates into two liquids upon cooling and 2) is also well established as an analogue to solidification phenomena observed in metals. Segregation was significantly reduced when the mixtures were subjected to ultrasonic energy during directional solidification processing. The processing parameters introduced by this application have been evaluated in view of optimizing dispersion uniformity. The improvement is in good agreement with a novel model that 1) predicts the achievable size of the droplets as a function of applied ultrasonic energy and then 2) calculates their relative sinking velocity through the bulk liquid.

  20. Gelatin-Filtered Consomme: A Practical Demonstration of the Freezing and Thawing Processes

    Science.gov (United States)

    Lahne, Jacob B.; Schmidt, Shelly J.

    2010-01-01

    Freezing is a key food processing and preservation technique widely used in the food industry. Application of best freezing and storage practices extends the shelf-life of foods for several months, while retaining much of the original quality of the fresh food. During freezing, as well as its counterpart process, thawing, a number of critical…

  1. Dynamic Modeling and Validation of a Biomass Hydrothermal Pretreatment Process - A Demonstration Scale Study

    DEFF Research Database (Denmark)

    Prunescu, Remus Mihail; Blanke, Mogens; Jakobsen, Jon Geest

    2015-01-01

    Hydrothermal pretreatment of lignocellulosic biomass is a cost effective technology for second generation biorefineries. The process occurs in large horizontal and pressurized thermal reactors where the biomatrix is opened under the action of steam pressure and temperature to expose cellulose...... for the enzymatic hydrolysis process. Several by-products are also formed, which disturb and act as inhibitors downstream. The objective of this study is to formulate and validate a large scale hydrothermal pretreatment dynamic model based on mass and energy balances, together with a complex conversion mechanism...... of the process, outlining the value of the model for simulation, control design, and optimization for full-scale applications....

  2. SITE PROGRAM DEMONSTRATION ECO LOGIC INTERNATIONAL GAS-PHASE CHEMICAL REDUCTION PROCESS, BAY CITY, MICHIGAN TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    The SITE Program funded a field demonstration to evaluate the Eco Logic Gas-Phase Chemical Reduction Process developed by ELI Eco Logic International Inc. (ELI), Ontario, Canada. The Demonstration took place at the Middleground Landfill in Bay City, Michigan using landfill wa...

  3. Demonstrating Reliable High Level Waste Slurry Sampling Techniques to Support Hanford Waste Processing

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Steven E.

    2013-11-11

    The Hanford Tank Operations Contractor (TOC) and the Hanford Waste Treatment and Immobilization Plant (WTP) contractor are both engaged in demonstrating mixing, sampling, and transfer system capability using simulated Hanford High-Level Waste (HL W) formulations. This work represents one of the remaining technical issues with the high-level waste treatment mission at Hanford. The TOC must demonstrate the ability to adequately mix and sample high-level waste feed to meet the WTP Waste Acceptance Criteria and Data Quality Objectives. The sampling method employed must support both TOC and WTP requirements. To facilitate information transfer between the two facilities the mixing and sampling demonstrations are led by the One System Integrated Project Team. The One System team, Waste Feed Delivery Mixing and Sampling Program, has developed a full scale sampling loop to demonstrate sampler capability. This paper discusses the full scale sampling loops ability to meet precision and accuracy requirements, including lessons learned during testing. Results of the testing showed that the Isolok(R) sampler chosen for implementation provides precise, repeatable results. The Isolok(R) sampler accuracy as tested did not meet test success criteria. Review of test data and the test platform following testing by a sampling expert identified several issues regarding the sampler used to provide reference material used to judge the Isolok's accuracy. Recommendations were made to obtain new data to evaluate the sampler's accuracy utilizing a reference sampler that follows good sampling protocol.

  4. DEMONSTRATION BULLETIN: CAV-OX ULTRAVIOLET OXIDATION PROCESS MAGNUM WATER TECHNOLOGY

    Science.gov (United States)

    The CAV-OX® technology (see Fig- ure 1) destroys organic contaminants, including chlorinated hy- drocarbons, in water. The process uses hydrogen peroxide, hy- drodynamic cavitation, and ultraviolet (UV) radiation to photolyze and oxidize organic compounds present in water at ...

  5. DEMONSTRATION BULLETIN: CAV-OX ULTRAVIOLET OXIDATION PROCESS MAGNUM WATER TECHNOLOGY

    Science.gov (United States)

    The CAV-OX® technology (see Fig- ure 1) destroys organic contaminants, including chlorinated hy- drocarbons, in water. The process uses hydrogen peroxide, hy- drodynamic cavitation, and ultraviolet (UV) radiation to photolyze and oxidize organic compounds present in water at ...

  6. Advanced coal conversion process demonstration. Technical progress report for the period July 1, 1995--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from July 1, 1995 through September 30, 1995. The ACCP Demonstration Project is a US Department of Energy (DOE) Clean Coal Technology Project. This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low-rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the cola is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal.

  7. Dynamic Modeling and Validation of a Biomass Hydrothermal Pretreatment Process - A Demonstration Scale Study

    DEFF Research Database (Denmark)

    Prunescu, Remus Mihail; Blanke, Mogens; Jakobsen, Jon Geest;

    2015-01-01

    Hydrothermal pretreatment of lignocellulosic biomass is a cost effective technology for second generation biorefineries. The process occurs in large horizontal and pressurized thermal reactors where the biomatrix is opened under the action of steam pressure and temperature to expose cellulose for...... of the process, outlining the value of the model for simulation, control design, and optimization for full-scale applications. This article is protected by copyright. All rights reserved....

  8. Micellar casein concentrate production with a 3X, 3-stage, uniform transmembrane pressure ceramic membrane process at 50°C.

    Science.gov (United States)

    Hurt, E; Zulewska, J; Newbold, M; Barbano, D M

    2010-12-01

    The production of serum protein (SP) and micellar casein from skim milk can be accomplished using microfiltration (MF). Potential commercial applications exist for both SP and micellar casein. Our research objective was to determine the total SP removal and SP removal for each stage, and the composition of retentates and permeates, for a 3×, continuous bleed-and-feed, 3-stage, uniform transmembrane pressure (UTP) system with 0.1-μm ceramic membranes, when processing pasteurized skim milk at 50°C with 2 stages of water diafiltration. For each of 4 replicates, about 1,100 kg of skim milk was pasteurized (72°C, 16s) and processed at 3× through the UTP MF system. Retentate from stage 1 was cooled to Kjeldahl methods; sodium dodecyl sulfate-PAGE analysis was also performed on the retentates from each stage. Theoretically, a 3-stage, 3× MF process could remove 97% of the SP from skim milk, with a cumulative SP removal of 68 and 90% after the first and second stages, respectively. The cumulative SP removal using a 3-stage, 3× MF process with a UTP system with 0.01-μm ceramic membranes in this experiment was 64.8 ± 0.8, 87.8 ± 1.6, and 98.3 ± 2.3% for the first, second, and third stages, respectively, when calculated using the mass of SP removed in the permeate of each stage. Various methods of calculation of SP removal were evaluated. Given the analytical limitations in the various methods for measuring SP removal, calculation of SP removal based on the mass of SP in the skim milk (determined by Kjeldahl) and the mass SP present in all of the permeate produced by the process (determined by Kjeldahl) provided the best estimate of SP removal for an MF process.

  9. 均匀设计优化杏鲍菇酒发酵工艺%Optimization of Fermentation Process for Pleurotus Eryngii Wine by Uniform Design

    Institute of Scientific and Technical Information of China (English)

    田广文; 王莹; 陈德育

    2014-01-01

    Using defective pleurotus eryngii as the raw material, research to optimize the fermentation process of pleurotus eryngii Wine by uniform design principle. The results showed that, the mash acidity and the amount of yeast is not significant on the quality of the wine; the eryngii amount, Brix, the main fermentation time is extremely significant on the quality of the wine, and the order is the main fermentation time> Brix> eryngii amount. The optimal fermentation technical parameters from the regression analysis of uniform experiment is eryngii amount 8%, Brix 22%, acidity 0.4%, inoculum size 6%, 26℃17 d. The eryngii wine is wine degree 11.7, sensory score of 92, and has a unique typical the eryngii aroma and pure flavor of wine.%以残次杏鲍菇为原料,采用均匀试验设计原理优化杏鲍菇酿酒发酵工艺。结果表明,醪液酸度和酵母接种量对酒品质影响不显著;而菇浆量、糖度、主发酵时间对酒品质影响极其显著,次序为主发酵时间>糖度>菇浆量。试验均匀回归分析得出最优发酵工艺参数为:菇浆量8%,糖度22%,酸度0.4%,接种量6%,26℃下主发酵17 d,由此酿制的杏鲍菇酒酒度11.7,感官评分92,具有独特典型的杏鲍菇香气和纯正的酒香风味。

  10. Fuel and power coproduction: The Liquid Phase Methanol (LPMEOH{trademark}) process demonstration at Kingsport

    Energy Technology Data Exchange (ETDEWEB)

    Drown, D.P.; Brown, W.R.; Heydorn, E.C.; Moore, R.B.; Schaub, E.S.; Brown, D.M.; Jones, W.C.; Kornosky, R.M.

    1997-12-31

    The Liquid Phase Methanol (LPMEOH{trademark}) process uses a slurry bubble column reactor to convert syngas (primarily a mixture of carbon monoxide and hydrogen) to methanol. Because of its superior heat management, the process is able to be designed to directly handle the carbon monoxide (CO)-rich syngas characteristic of the gasification of coal, petroleum coke, residual oil, wastes, or of other hydrocarbon feedstocks. When added to an integrated gasification combined cycle (IGCC) power plant, the LPMEOH{trademark} process converts a portion of the CO-rich syngas produced by the gasifier to methanol, and the remainder of the unconverted gas is used to fuel the gas turbine combined-cycle power plant. The LPMEOH{trademark} process has the flexibility to operate in a daily electricity demand load-following manner. Coproduction of power and methanol via IGCC and the LPMEOH{trademark} process provides opportunities for energy storage for electrical demand peak shaving, clean fuel for export, and/or chemical methanol sales.

  11. Field Demonstration of a Novel Biotreatment Process for Perchlorate Reduction in Groundwater

    Science.gov (United States)

    2010-12-01

    Certification Program FeCO3 siderite FOB freight on board ID inside diameter Mo molybdenum MPN most probably number NaHCO3 sodium bicarbonate...of an organic substrate.  Possibility of treating both perchlorate and possible co-contaminants such as nitrate, chlorinated solvents such as TCE...continuously extracted from a single well, from where it was distributed to the different demonstration projects. The water average contaminant

  12. Optimization of H2O2 dosage in microwave-H2O2 process for sludge pretreatment with uniform design method

    Institute of Scientific and Technical Information of China (English)

    Qingcong Xiao; Hong Yan; Yuansong Wei; Yawei Wang; Fangang Zeng; Xiang Zheng

    2012-01-01

    A microwave-H2O2 process for sludge pretreatment exhibited high efficiencies of releasing organics,nitrogen,and phosphorus,but large quantities of H2O2 residues were detected.A uniform design method was thus employed in this study to further optimize H2O2 dosage by investigating effects of pH and H2O2 dosage on the amount of H2O2 residue and releases of organics,nitrogen,and phosphorus.A regression model was established with pH and H2O2 dosage as the independent variables,and H2O2 residue and releases of organics,nitrogen,and phosphorus as the dependent variables.In the optimized microwave-H2O2 process,the pH value of the sludge was firstly adjusted to 11.0,then the sludge was heated to 80C and H2O2 was dosed at a H2O2:mixed liquor suspended solids (MLSS) ratio of 0.2,and the sludge was finally heated to 100℃ by microwave irradiation.Compared to the microwave-H2O2 process without optimization,the H2O2 dosage and the utilization rate of H2O2 in the optimized microwave-H2O2 process were reduced by 80% and greatly improved by 3.87 times,respectively,when the H2O2:MLSS dosage ratio was decreased from 1.0 to 0.2,resulting in nearly the same release rate of soluble chemical oxygen demand in the microwave-H2O2 process without optimization at H2O2:MLSS ratio of 0.5.

  13. 77 FR 11677 - Medicaid Program; Review and Approval Process for Section 1115 Demonstrations

    Science.gov (United States)

    2012-02-27

    ... should assure public input. From time to time that process has come under criticism. In recent years, the..., as well as to provide information on historical expenditures. Response: The information requested by... budget neutrality, we require States to submit historical Medicaid expenditure data for all...

  14. Demonstration of a crown ether process for partitioning strontium from high level liquid waste (HLLW)

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jianchen; Jing, Shan; Chen, Jing [Tsinghua Univ., Beijing (China). Inst. of Nuclear and New Energy Technology (INET); Tsinghua Univ., Beijing (China). Beijing Key Lab of Radioactive Waste Treatment

    2016-05-01

    Chinese HLLW with a higher-salt liquid that was generated via plutonium uranium recovery by extraction (PUREX) processing was temporarily stored in stainless steel tanks and is waiting for treatment. The volume and heat-loading of the glass block are reduced if the strontium, cesium, actinides and other long-life radioactive elements, such as Tc in the HLLW, are partitioned before the HLLW verification. This process is beneficial to preserve the capacity of the geological disposal repository and to minimize long-term hazards. The process of partitioning strontium from Chinese HLLW using Dicyclohexano-18Crown-6(DCH18C-6) was developed in past decades, including such fundamental studies as the small scale cold and hot test. In this work, new studies are introduced, including the cold and the long time hot cascade tests, using a miniature centrifugal contactor set and the pilot-scale cold test using pulse extraction columns. The results indicate that the crown process is promising for partitioning strontium from Chinese HLLW.

  15. Demonstration of Geomorphic Processes and Landform Evolution Through MATLAB GUI Apps

    Science.gov (United States)

    Adams, P. N.

    2016-12-01

    Although some rapid events can alter the landscape almost instantaneously (e.g. landslides, cliff failures), many geomorphic processes operate on time scales that are slower than human observation intervals (e.g. hillslope diffusion, isostatic uplift). Because these "slower" processes are more challenging for undergraduate students to conceptualize, it is illustrative to present topographic change through computer simulations that honor the physics of the geomorphic processes, but have the ability to speed up geologic time thereby providing a clear visualization of landscape evolution. As part of a project to produce a series of visualizations to illustrate coupled geomorphic processes and the landforms they produce, I present two MATLAB Apps that provide Graphical User Interfaces (GUIs) that allow students to manipulate rates and magnitudes of processes and observe the computed geomorphic results. In a GUI app that simulates hillslope diffusion in response to an evolving topographic gradient, the student user sets the rate of bedrock river downcutting, the rate of regional uplift, and the diffusivity parameter, then the model produces an animation that shows how the interfluves evolve through gradient-driven hillslope material transport. In a GUI app that simulates regional isostatic uplift in response to bedrock river incision, the student user sets the incision rate and the densities of crust and mantle, respectively, then the model produces an animation that shows how the mountain peaks uplift higher than the original ridgeline and how the Moho rises while the mean topographic surface elevation lowers. By providing students with a range of values for the input parameters, students can explore the computed landscape evolution results by simple inspection of the graphical output. In addition, students are introduced to the code that produced the GUI, in an effort to demystify the production of apps and encourage the use of MATLAB to complete assignments that

  16. Test plan: the Czechowice Oil Refinery bioremediation demonstration of a process waste lagoon

    Energy Technology Data Exchange (ETDEWEB)

    Altman, D.J.; Lombard, K.H.; Hazen, T.C.

    1997-03-31

    The remediation strategies that will be applied at the Czechowice Oil Refinery waste lagoon in Czechowice, Poland are designed, managed, and implemented under the direction of the Westinghouse Savannah River Company (WSRC) for the United States Department of Energy (DOE). WSRC will be assisted in the demonstration by The Institute for Ecology of Industrial Areas (IETU). This collaboration between IETU and DOE will provide the basis for international technology transfer of new and innovative remediation technologies that can be applied in Poland and the Eastern European Region as well.

  17. Demonstrating compliance with WAPS 1.3 in the Hanford waste vitrification plant process

    Energy Technology Data Exchange (ETDEWEB)

    Bryan, M.F.; Piepel, G.F.; Simpson, D.B.

    1996-03-01

    The high-level waste (HLW) vitrification plant at the Hanford Site was being designed to immobilize transuranic and high-level radioactive waste in borosilicate glass. This document describes the statistical procedure to be used in verifying compliance with requirements imposed by Section 1.3 of the Waste Acceptance Product Specifications (WAPS, USDOE 1993). WAPS 1.3 is a specification for ``product consistency,`` as measured by the Product Consistency Test (PCT, Jantzen 1992b), for each of three elements: lithium, sodium, and boron. Properties of a process batch and the resulting glass are largely determined by the composition of the feed material. Empirical models are being developed to estimate some property values, including PCT results, from data on feed composition. These models will be used in conjunction with measurements of feed composition to control the HLW vitrification process and product.

  18. Instrumentation and process control for fossil demonstration plants. Quarterly technical progress report, October--December 1976

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L. G.; O' Fallon, N. M; Bump, T. R.; Cohn, C. E.; Doering, R. W.; Duffey, D.; Kirsch,; Lipinski, W. C.; Managan, W. W.; Porges, K. G.; Raptis, A. C.

    1977-01-01

    The final report of the state-of-the-art study of instrumentation for process control and safety in large-scale coal conversion and fluidized-bed combustion systems was distributed in November. A conceptual design for the Solids/Gas Flow Test Facility has been initiated, the major components identified, and vendors located. Work on acoustic flow measurement has included theoretical feasibility studies of acoustic/ultrasonic techniques for mass-flow measurements of slurries and solid/gas media. Initial planning was conducted to establish a laboratory facility necessary to verify theoretical findings. A survey of the literature relating to capacitive measurements was begun to provide a basis for conceptual designs and preliminary bench tests of the feasibility of these designs. Conceptual design of a capacitive on-line solids density measuring device and calculations to select the type of system for initial feasibility tests were carried out. Preliminary tests of neutron capture gamma analysis for on-line elemental composition of liquid and solid streams in coal plants indicate that most coal elements can be detected quantitatively through the pipe walls. A computer program for peak-fitting in the gamma spectrum was modified for requirements of this work. A literature search was started to determine the state-of-the-art in dynamic process modeling of fossil energy system components, physical property models, and process control models. A partial review of abstracts from a computerized literature search has identified over 50 references having possible application to process analysis activities in this program.

  19. DEMONSTRATION OF THE STRATEGY FORMATION PROCESS: A CASE STUDY IN A INNOVATIVE ORGANIZATION

    Directory of Open Access Journals (Sweden)

    Daniel Teodoro Gomes

    2012-05-01

    Full Text Available This paper presents a study of strategy formation process with the following starting question: "How the strategy is shaped in an innovative company and how the factors manifesting in the process?". The research builds on a case study of a company considered innovative leader in its industry and a pioneer in providing various services in the area of mobile phone in Brazil. Data collection was through interviews semi-structured with directors and managers involved in strategy formation, supplemented by documents and direct observation. Data analysis is based on the techniques of discourse analysis, from the persuasion strategies suggested by Linhares and Faria (1993. The company's strategy studied can be defined as an entrepreneurial vision, focused on growth supported by a process of diversification of product lines from a new direction composed of three elements: (i componentization; (ii segmentation by products chain and; (iii external to finance leverage in order to resumption of innovative projects. It was concluded that the company's strategy focused on these three factors, supported by a deliberate vision of the future, conditions its historical trajectory type standard cultural, its core values, which acts as a motivator and guide for members of the organization decisions and actions.

  20. Great gas plants : these five natural gas processing facilities demonstrate decades of top-flight technology

    Energy Technology Data Exchange (ETDEWEB)

    Byfield, M.

    2010-07-15

    The natural gas purification and pipeline sector is a major economic driver in Canada. Gas processing facilities are growing in number, and several large gas projects are being planned for future construction in the western provinces. This article outlined 5 gas plants in order to illustrate the sector's history and breadth in Canada. The Shell Jumping Pound gas complex was constructed in 1951 after a sulfur-rich gas discovery near Calgary in 1944. The Empress Straddle plant was built in 1971 in southeastern Alberta and is one of the largest single industrial consumers of electrical power in the province. The Fort Nelson gas processing plant is North America's largest sour gas processing facility. The Shell Caroline complex was built 1993. The Sable offshore energy project is located on the coast of Nova Scotia to handle gas produced from the Thebaud wells. A consortium is now considering the development of new gas fields in the Sable area. 5 figs.

  1. Quasi-uniform Space

    Directory of Open Access Journals (Sweden)

    Coghetto Roland

    2016-09-01

    Full Text Available In this article, using mostly Pervin [9], Kunzi [6], [8], [7], Williams [11] and Bourbaki [3] works, we formalize in Mizar [2] the notions of quasiuniform space, semi-uniform space and locally uniform space.

  2. Test plan, the Czechowice Oil Refinery bioremediation demonstration of a process waste lagoon. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Altman, D.J.; Hazen, T.C.; Tien, A.J. [Westinghouse Savannah River Co., Aiken, SC (United States). Savannah River Technology Center; Worsztynowicz, A.; Ulfig, K. [Inst. for Ecology of Industrial Areas, Katowice (Poland)

    1997-05-10

    The overall objective of the bioremediation project is to provide a cost effective bioremediation demonstration of petroleum contaminated soil at the Czechowice Oil Refinery. Additional objectives include training of personnel, and transfer of this technology by example to Poland, and the Risk Abatement Center for Central and Eastern Europe (RACE). The goal of the remediation is to reduce the risk of PAH compounds in soil and provide a green zone (grassy area) adjacent to the site boundary. Initial project discussions with the Czechowice Oil Refinery resulted in helping the refinery find an immediate cost effective solution for the dense organic sludge in the lagoons. They found that when mixed with other waste materials, the sludge could be sold as a fuel source to local cement kilns. Thus the waste was incinerated and provided a revenue stream for the refinery to cleanup the lagoon. This allowed the bioremediation project to focus on remediation of contaminated soil that unusable as fuel, less recalcitrant and easier to handle and remediate. The assessment identified 19 compounds at the refinery that represented significant risk and would require remediation. These compounds consisted of metals, PAH`s, and BTEX. The contaminated soil to be remediated in the bioremediation demonstration contains only PAH (BTEX and metals are not significantly above background concentrations). The final biopile design consists of (1) dewatering and clearing lagoon A to clean clay, (2) adding a 20 cm layer of dolomite with pipes for drainage, leachate collection, air injection, and pH adjustment, (3) adding a 1.1 m layer of contaminated soil mixed with wood chips to improve permeability, and (4) completing the surface with 20 cm of top soil planted with grass.

  3. Event Detection Intelligent Camera: Demonstration of flexible, real-time data taking and processing

    Energy Technology Data Exchange (ETDEWEB)

    Szabolics, Tamás, E-mail: szabolics.tamas@wigner.mta.hu; Cseh, Gábor; Kocsis, Gábor; Szepesi, Tamás; Zoletnik, Sándor

    2015-10-15

    Highlights: • We present EDICAM's operation principles description. • Firmware tests results. • Software test results. • Further developments. - Abstract: An innovative fast camera (EDICAM – Event Detection Intelligent CAMera) was developed by MTA Wigner RCP in the last few years. This new concept was designed for intelligent event driven processing to be able to detect predefined events and track objects in the plasma. The camera provides a moderate frame rate of 400 Hz at full frame resolution (1280 × 1024), and readout of smaller region of interests can be done in the 1–140 kHz range even during exposure of the full image. One of the most important advantages of this hardware is a 10 Gbit/s optical link which ensures very fast communication and data transfer between the PC and the camera, enabling two level of processing: primitive algorithms in the camera hardware and high-level processing in the PC. This camera hardware has successfully proven to be able to monitoring the plasma in several fusion devices for example at ASDEX Upgrade, KSTAR and COMPASS with the first version of firmware. A new firmware and software package is under development. It allows to detect predefined events in real time and therefore the camera is capable to change its own operation or to give warnings e.g. to the safety system of the experiment. The EDICAM system can handle a huge amount of data (up to TBs) with high data rate (950 MB/s) and will be used as the central element of the 10 camera overview video diagnostic system of Wendenstein 7-X (W7-X) stellarator. This paper presents key elements of the newly developed built-in intelligence stressing the revolutionary new features and the results of the test of the different software elements.

  4. Do School Uniforms Fit?

    Science.gov (United States)

    White, Kerry A.

    2000-01-01

    In 1994, Long Beach (California) Unified School District began requiring uniforms in all elementary and middle schools. Now, half of all urban school systems and many suburban schools have uniform policies. Research on uniforms' effectiveness is mixed. Tightened dress codes may be just as effective and less litigious. (MLH)

  5. School Uniforms Redux.

    Science.gov (United States)

    Dowling-Sendor, Benjamin

    2002-01-01

    Reviews a recent decision in "Littlefield" by the 5th Circuit upholding a school uniform policy. Advises board member who wish to adopt a school uniform policy to solicit input from parents and students, research the experiences of other school districts with uniform policies, and articulate the interests they wish to promote through uniform…

  6. Towards an optimized flow-sheet for a SANEX demonstration process using centrifugal contactors

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, D. [European Commission, Joint Research Center, Karlsruhe (Germany). Inst. for Transuranium Elements; Chalmers Univ. of Technology, Gothenburg (Sweden). Nuclear Chemistry, Dept. of Chemical and Biological Engineering; Christiansen, B.; Glatz, J.P.; Malmbeck, R.; Serrano-Purroy, D. [European Commission, Joint Research Center, Karlsruhe (Germany). Inst. for Transuranium Elements; Modolo, G. [Forschungszentrum Juelich GmbH (Germany). Inst. for Energy Research, Safety Research and Reactor Technology; Sorel, C. [Commissariat a l' Energie Atomique Valrho (CEA), DRCP/SCPS, Bagnols-sur-Ceze (France)

    2009-07-01

    The design of an efficient process flow-sheet requires accurate extraction data for the experimental set-up used. Often this data is provided as equilibrium data. Due to the small hold-up volume compared to the flow rate in centrifugal contactors the time for extraction is often too short to reach equilibrium D-ratios. In this work single stage kinetics experiments have been carried out to investigate the D-ratio dependence of the flow rate and to compare this with equilibrium batch experiments for a SANEX system based on CyMe{sub 4}-BTBP. The first centrifuge experiment was run with spiked solutions while in the second a genuine actinide/lanthanide fraction from a TODGA process was used. Three different flow rates were tested with each set-up. The results show that even with low flow rates, only around 9% of the equilibrium D-ratio (Am) was reached for the extraction in the spiked test and around 16% in the hot test (the difference is due to the size of the centrifuges). In the hot test the lanthanide scrubbing was inefficient whereas in the stripping both the actinides and the lanthanides showed good results. Based on these results improvements of the suggested flow-sheet is discussed. (orig.)

  7. Demonstration of the waste tire pyrolysis process on pilot scale in a continuous auger reactor.

    Science.gov (United States)

    Martínez, Juan Daniel; Murillo, Ramón; García, Tomás; Veses, Alberto

    2013-10-15

    This work shows the technical feasibility for valorizing waste tires by pyrolysis using a pilot scale facility with a nominal capacity of 150 kWth. A continuous auger reactor was operated to perform thirteen independent experiments that conducted to the processing of more than 500 kg of shredded waste tires in 100 h of operation. The reaction temperature was 550°C and the pressure was 1 bar in all the runs. Under these conditions, yields to solid, liquid and gas were 40.5 ± 0.3, 42.6 ± 0.1 and 16.9 ± 0.3 wt.% respectively. Ultimate and proximate analyses as well as heating value analysis were conducted for both the solid and liquid fraction. pH, water content, total acid number (TAN), viscosity and density were also assessed for the liquid and compared to the specifications of marine fuels (standard ISO 8217). Gas chromatography was used to calculate the composition of the gaseous fraction. It was observed that all these properties remained practically invariable along the experiments without any significant technical problem. In addition, the reaction enthalpy necessary to perform the waste tire pyrolysis process (907.1 ± 40.0 kJ/kg) was determined from the combustion and formation enthalpies of waste tire and conversion products. Finally, a mass balance closure was performed showing an excellent reliability of the data obtained from the experimental campaign.

  8. Uniformly rotating neutron stars

    CERN Document Server

    Boshkayev, Kuantay

    2016-01-01

    In this chapter we review the recent results on the equilibrium configurations of static and uniformly rotating neutron stars within the Hartle formalism. We start from the Einstein-Maxwell-Thomas-Fermi equations formulated and extended by Belvedere et al. (2012, 2014). We demonstrate how to conduct numerical integration of these equations for different central densities ${\\it \\rho}_c$ and angular velocities $\\Omega$ and compute the static $M^{stat}$ and rotating $M^{rot}$ masses, polar $R_p$ and equatorial $R_{\\rm eq}$ radii, eccentricity $\\epsilon$, moment of inertia $I$, angular momentum $J$, as well as the quadrupole moment $Q$ of the rotating configurations. In order to fulfill the stability criteria of rotating neutron stars we take into considerations the Keplerian mass-shedding limit and the axisymmetric secular instability. Furthermore, we construct the novel mass-radius relations, calculate the maximum mass and minimum rotation periods (maximum frequencies) of neutron stars. Eventually, we compare a...

  9. Interated Intelligent Industrial Process Sensing and Control: Applied to and Demonstrated on Cupola Furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed Abdelrahman; roger Haggard; Wagdy Mahmoud; Kevin Moore; Denis Clark; Eric Larsen; Paul King

    2003-02-12

    The final goal of this project was the development of a system that is capable of controlling an industrial process effectively through the integration of information obtained through intelligent sensor fusion and intelligent control technologies. The industry of interest in this project was the metal casting industry as represented by cupola iron-melting furnaces. However, the developed technology is of generic type and hence applicable to several other industries. The system was divided into the following four major interacting components: 1. An object oriented generic architecture to integrate the developed software and hardware components @. Generic algorithms for intelligent signal analysis and sensor and model fusion 3. Development of supervisory structure for integration of intelligent sensor fusion data into the controller 4. Hardware implementation of intelligent signal analysis and fusion algorithms

  10. Microarray meta-analysis database (M2DB: a uniformly pre-processed, quality controlled, and manually curated human clinical microarray database

    Directory of Open Access Journals (Sweden)

    Cheng Wei-Chung

    2010-08-01

    Full Text Available Abstract Background Over the past decade, gene expression microarray studies have greatly expanded our knowledge of genetic mechanisms of human diseases. Meta-analysis of substantial amounts of accumulated data, by integrating valuable information from multiple studies, is becoming more important in microarray research. However, collecting data of special interest from public microarray repositories often present major practical problems. Moreover, including low-quality data may significantly reduce meta-analysis efficiency. Results M2DB is a human curated microarray database designed for easy querying, based on clinical information and for interactive retrieval of either raw or uniformly pre-processed data, along with a set of quality-control metrics. The database contains more than 10,000 previously published Affymetrix GeneChip arrays, performed using human clinical specimens. M2DB allows online querying according to a flexible combination of five clinical annotations describing disease state and sampling location. These annotations were manually curated by controlled vocabularies, based on information obtained from GEO, ArrayExpress, and published papers. For array-based assessment control, the online query provides sets of QC metrics, generated using three available QC algorithms. Arrays with poor data quality can easily be excluded from the query interface. The query provides values from two algorithms for gene-based filtering, and raw data and three kinds of pre-processed data for downloading. Conclusion M2DB utilizes a user-friendly interface for QC parameters, sample clinical annotations, and data formats to help users obtain clinical metadata. This database provides a lower entry threshold and an integrated process of meta-analysis. We hope that this research will promote further evolution of microarray meta-analysis.

  11. Uniform, High Efficiency, Hybrid CIGS Process with Application to Novel Device Structures: Annual Technical Report, 15 March 2005 - 14 March 2006

    Energy Technology Data Exchange (ETDEWEB)

    Delahoy, A. E.; Chen, L.; Sang, B.

    2006-06-01

    One of the main Phase I objectives of this subcontract was for EPV to demonstrate 14%-efficient CIGS devices using a hybrid process. The processing was also required to have good control ability. These goals were successfully accomplished. It will be seen that during Phase I, we successfully developed a new, simplified hybrid process. A highlight of intensive work was the achievement of a 14.0% NREL-verified device at a CIGS thickness of 1.13 ..mu..m. The simplified hybrid process considerably reduces CIGS film formation time and offers the promise of being a truly cost-effective and manufacturable one. It is considered to be one of the more attractive CIGS processes in the industry.

  12. Accelerating electrostatic interaction calculations with graphical processing units based on new developments of Ewald method using non-uniform fast Fourier transform.

    Science.gov (United States)

    Yang, Sheng-Chun; Wang, Yong-Lei; Jiao, Gui-Sheng; Qian, Hu-Jun; Lu, Zhong-Yuan

    2016-01-30

    We present new algorithms to improve the performance of ENUF method (F. Hedman, A. Laaksonen, Chem. Phys. Lett. 425, 2006, 142) which is essentially Ewald summation using Non-Uniform FFT (NFFT) technique. A NearDistance algorithm is developed to extensively reduce the neighbor list size in real-space computation. In reciprocal-space computation, a new algorithm is developed for NFFT for the evaluations of electrostatic interaction energies and forces. Both real-space and reciprocal-space computations are further accelerated by using graphical processing units (GPU) with CUDA technology. Especially, the use of CUNFFT (NFFT based on CUDA) very much reduces the reciprocal-space computation. In order to reach the best performance of this method, we propose a procedure for the selection of optimal parameters with controlled accuracies. With the choice of suitable parameters, we show that our method is a good alternative to the standard Ewald method with the same computational precision but a dramatically higher computational efficiency.

  13. Uniform decoration of vanadium oxide nanocrystals on reduced graphene-oxide balls by an aerosol process for lithium-ion battery cathode material.

    Science.gov (United States)

    Choi, Seung Ho; Kang, Yun Chan

    2014-05-19

    VO2-decorated reduced graphene balls were prepared by a one-pot spray-pyrolysis process from a colloidal spray solution of well-dispersed graphene oxide and ammonium vanadate. The graphene-VO2 composite powders prepared directly by spray pyrolysis had poor electrochemical properties. Therefore, the graphene-VO2 composite powders were transformed into a reduced graphene ball (RGB)-V2O5 (RGB) composite by post-treatment at 300 °C in an air atmosphere. The TEM and dot-mapping images showed a uniform distribution of V and C components, originating from V2O5 and graphene, consisting the composite. The graphene content of the RGB-V2O5 composite, measured by thermogravimetric analysis, was approximately 5 wt %. The initial discharge and charge capacities of RGB-V2O5 composite were 282 and 280 mA h g(-1), respectively, and the corresponding Coulombic efficiency was approximately 100 %. On the other hand, the initial discharge and charge capacities of macroporous V2O5 powders were 205 and 221 mA h g(-1), respectively, and the corresponding Coulombic efficiency was approximately 93 %. The RGB-V2O5 composite showed a better rate performance than the macroporous V2O5 powders.

  14. FIELD DEMONSTRATION OF A MEMBRANE PROCESS TO RECOVER HEAVY HYDROCARBONS AND TO REMOVE WATER FROM NATURAL GAS

    Energy Technology Data Exchange (ETDEWEB)

    R. Baker; T. Hofmann; J. Kaschemekat; K.A. Lokhandwala; Membrane Group; Module Group; Systems Group

    2001-01-11

    The objective of this project is to design, construct and field demonstrate a 3-MMscfd membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world conditions is required to convince industry users of the efficiency and reliability of the process. The system will be designed and fabricated by Membrane Technology and Research, Inc. (MTR) and then installed and operated at British Petroleum (BP)-Amoco's Pascagoula, MS plant. The Gas Research Institute will partially support the field demonstration and BP-Amoco will help install the unit and provide onsite operators and utilities. The gas processed by the membrane system will meet pipeline specifications for dewpoint and Btu value and can be delivered without further treatment to the pipeline. Based on data from prior membrane module tests, the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. At the end of this demonstration project the process will be ready for commercialization. The route to commercialization will be developed during this project and may involve collaboration with other companies already servicing the natural gas processing industry.

  15. FIELD DEMONSTRATION OF A MEMBRANE PROCESS TO RECOVER HEAVY HYDROCARBONS AND TO REMOVE WATER FROM NATURAL GAS

    Energy Technology Data Exchange (ETDEWEB)

    R. Baker; R. Hofmann; K.A. Lokhandwala

    2003-02-14

    The objective of this project is to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world conditions would convince industry users of the efficiency and reliability of the process. The system has been designed and fabricated by Membrane Technology and Research, Inc. (MTR) and will be installed and operated at British Petroleum (BP)-Amoco's Pascagoula, MS plant. The Gas Research Institute will partially support the field demonstration and BP-Amoco will help install the unit and provide onsite operators and utilities. The gas processed by the membrane system will meet pipeline specifications for dewpoint and Btu value and can be delivered without further treatment to the pipeline. Based on data from prior membrane module tests, the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. At the end of this demonstration project the process will be ready for commercialization. The route to commercialization will be developed during this project and may involve collaboration with other companies already servicing the natural gas processing industry.

  16. Field Demonstration of a Membrane Process to Recover Heavy Hydrocarbons and to Remove Water from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    R. Baker; T. Hofmann; K. A. Lokhandwala

    2006-09-29

    The objective of this project is to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world high-pressure conditions is being conducted to convince industry users of the efficiency and reliability of the process. The system was designed and fabricated by Membrane Technology and Research, Inc. (MTR) and installed and operated at BP Amoco's Pascagoula, MS plant. The Gas Research Institute is partially supporting the field demonstration and BP-Amoco helped install the unit and provides onsite operators and utilities. The gas processed by the membrane system meets pipeline specifications for dew point and BTU value and can be delivered without further treatment to the pipeline. Based on data from prior membrane module tests, the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. During the course of this project, MTR has sold 13 commercial units related to the field test technology, and by the end of this demonstration project the process will be ready for broader commercialization. A route to commercialization has been developed during this project and involves collaboration with other companies already servicing the natural gas processing industry.

  17. Field Demonstration of a Membrane Process to Recover Heavy Hydrocarbons and to Remove Water from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    R. Baker; T. Hofmann; K. A. Lokhandwala

    2004-09-29

    The objective of this project is to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world conditions would convince industry users of the efficiency and reliability of the process. The system has been designed and fabricated by Membrane Technology and Research, Inc. (MTR) and will be installed and operated at British Petroleum (BP)-Amoco's Pascagoula, MS plant. The Gas Research Institute will partially support the field demonstration and BP-Amoco will help install the unit and provide onsite operators and utilities. The gas processed by the membrane system will meet pipeline specifications for dewpoint and BTU value and can be delivered without further treatment to the pipeline. Based on data from prior membrane module tests, the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. At the end of this demonstration project the process will be ready for commercialization. The route to commercialization will be developed during this project and may involve collaboration with other companies already servicing the natural gas processing industry.

  18. Field Demonstration of a Membrane Process to Recover Heavy Hydrocarbons and to Remove Water from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    R. Baker; T. Hofmann; K. A. Lokhandwala

    2005-09-29

    The objective of this project is to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world high-pressure conditions is being conducted to convince industry users of the efficiency and reliability of the process. The system was designed and fabricated by Membrane Technology and Research, Inc. (MTR) and installed and operated at BP Amoco's Pascagoula, MS plant. The Gas Research Institute is partially supporting the field demonstration and BP-Amoco helped install the unit and provided onsite operators and utilities. The gas processed by the membrane system meets pipeline specifications for dewpoint and BTU value and can be delivered without further treatment to the pipeline. Based on data from prior membrane module tests, the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. During the course of this project, MTR has sold 11 commercial units related to the field test technology, and by the end of this demonstration project the process will be ready for broader commercialization. A route to commercialization has been developed during this project and involves collaboration with other companies already servicing the natural gas processing industry.

  19. Development and Demonstration of a Sulfate Precipitation Process for Hanford Waste Tank 241-AN-107

    Energy Technology Data Exchange (ETDEWEB)

    SK Fiskum; DE Kurath; BM Rapko

    2000-08-16

    A series of precipitation experiments were conducted on Hanford waste tank 241-AN-107 samples in an effort to remove sulfate from the matrix. Calcium nitrate was added directly to AN-107 sub-samples to yield several combinations of Ca:CO{sub 3} mole ratios spanning a range of 0:1 to 3:1 to remove carbonate as insoluble CaCO{sub 3}. Similarly barium nitrate was added directly to the AN-107 aliquots, or to the calcium pretreated AN-107 aliquots, giving of Ba:SO{sub 4} mole ratios spanning a range of 1:1 to 5:1 to precipitate sulfate as BaSO{sub 4}. Initial bulk carbonate removal was required for successful follow-on barium sulfate precipitation. A {ge} 1:1 mole ratio of Ca:CO{sub 3} was found to lower the carbonate concentration such that Ba would react preferentially with the sulfate. A follow-on 1:1 mole ratio of Ba:SO{sub 4} resulted in 70% sulfate removal. The experiment was scaled up with a 735-mL aliquot of AN-107 for more complete testing. Calcium carbonate and barium sulfate settling rates were determined and fates of selected cations, anions, and radionuclides were followed through the various process steps. Seventy percent of the sulfate was removed in the scale-up test while recovering 63% of the filtrate volume. Surprisingly, during the scale-up test a sub-sample of the CaCO{sub 3}/241-AN-107 slurry was found to lose fluidity upon standing for {le} 2 days. Metathesis with BaCO{sub 3} at ambient temperature was also evaluated using batch contacts at various BaCO{sub 3}:SO{sub 4} mole ratios with no measurable success.

  20. Experimental demonstration of a format-flexible single-carrier coherent receiver using data-aided digital signal processing.

    Science.gov (United States)

    Elschner, Robert; Frey, Felix; Meuer, Christian; Fischer, Johannes Karl; Alreesh, Saleem; Schmidt-Langhorst, Carsten; Molle, Lutz; Tanimura, Takahito; Schubert, Colja

    2012-12-17

    We experimentally demonstrate the use of data-aided digital signal processing for format-flexible coherent reception of different 28-GBd PDM and 4D modulated signals in WDM transmission experiments over up to 7680 km SSMF by using the same resource-efficient digital signal processing algorithms for the equalization of all formats. Stable and regular performance in the nonlinear transmission regime is confirmed.

  1. Commercial Demonstration of the Manufactured Aggregate Processing Technology Utilizing Spray Dryer Ash

    Energy Technology Data Exchange (ETDEWEB)

    Milton Wu; Paul Yuran

    2006-12-31

    Universal Aggregates LLC (UA) was awarded a cost sharing Co-operative Agreement from the Department of Energy (DOE) through the Power Plant Improvement Initiative Program (PPII) to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia in October 2001. The Agreement was signed in November 2002. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the UA share is $12.3 million (63%). The original project team consists of UA, SynAggs, LLC, CONSOL Energy Inc. and P. J. Dick, Inc. Using 115,000 ton per year of spray dryer ash (SDA), a dry FGD by-product from the power station, UA will produce 167,000 tons of manufactured lightweight aggregate for use in production of concrete masonry units (CMU). Manufacturing aggregate from FGD by-products can provide an economical high-volume use and substantially expand market for FGD by-products. Most of the FGD by-products are currently disposed of in landfills. Construction of the Birchwood Aggregate Facility was completed in March 2004. Operation startup was begun in April 2004. Plant Integration was initiated in December 2004. Integration includes mixing, extrusion, curing, crushing and screening. Lightweight aggregates with proper size gradation and bulk density were produced from the manufacturing aggregate plant and loaded on a stockpile for shipment. The shipped aggregates were used in a commercial block plant for CMU production. However, most of the production was made at low capacity factors and for a relatively short time in 2005. Several areas were identified as important factors to improve plant capacity and availability. Equipment and process control modifications and curing vessel clean up were made to improve plant operation in the first half of 2006. About 3,000 tons of crushed aggregate was produced in August 2006. UA is continuing to work to improve plant

  2. Demonstrating the Effects of Shop Flow Process Variability on the Air Force Depot Level Reparable Item Pipeline

    Science.gov (United States)

    1992-09-01

    DO41). AFLCR 57-4. Wright-Patterson AFB OH: HQ AFLC, 29 April 1983. 137 12. Goldratt , Eliyahu M. and Jeff Cox. The Goal. Croton-On-Hudson NY: North...manufacturing process (14:411). Goldratt and Cox give another example of the same impact of variability in their book The Goal when they demonstrated what

  3. A Finite Element Model for Wafer Materiall Removal Rate and Non-uniformity in Chemical Mechanical Polishing Process%机械化学抛光中晶圆材料切削率和非均匀性有限元模型

    Institute of Scientific and Technical Information of China (English)

    郭跃彬

    2001-01-01

    提出了一个机械化学抛光中晶圆材料非均匀性的有限元模型.通过分析压力、摩擦力、抛光垫和承载膜的可压缩性对晶圆的应力分布的影响,研究了抛光过程中晶圆厚度的不均匀性.结果证明非均匀剪应力是晶圆厚度变化的一个主要原因.这个模型也建立了声发射信号的变化和晶圆厚度不均匀性的关系.通过对晶圆材料切削率的声发射信号监测,证明了实验结果和模型预测值的一致性.%A 3D finite element model is presented for wafer non-uniformity in chemicalmechanical polishing(CMP)process. Film thickness non-uniformity of the wafer during CMPprocess was investigated by examining the influence of applied pressure, friction force,pad andcarrier film compressibility on stress distribution across the wafer diameter. It shows that non-uniform shear stress distribution on wafer plays an important role on the non-uniformity. Themodel relates the variation of acoustic emission (AE)signal from non-uniform stress distribu-tion on the wafer to its non-uniformity. The agreement between model prediction and experi-mental results is demonstrated by AE monitoring of material removal rate in CMP process.

  4. Accomplishing equilibrium in ALSEP: demonstrations of modified process chemistry on 3-D printed enhanced annular centrifugal contactors

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Wardle, K.E.; Gelis, A.V. [Nuclear Engineering Division, Argonne National Laboratory, Lemont, IL, 60439 (United States); Lumetta, G. [Paccific Northwest National Laboratory, Richland, WA (United States)

    2016-07-01

    The ALSEP (Actinide Lanthanide Separation Process) was developed to treat a PUREX raffinate stream by liquid-liquid extraction with the intent of separating trivalent minor actinides (Am/Cm; An) from trivalent fission-product lanthanides (Ln) and selected transition metals. The major components of the modified ALSEP process have been demonstrated on a modified 2-cm annular centrifugal contactor with an enhanced mixing zone using stable fission products and radiotracers. The results show that by decreasing the pH of the minor actinide stripping solution, using HEDTA instead of DTPA, and increasing contact time, the process is very effective in separating americium from the lanthanides and the fission products.

  5. Field Demonstration of a Membrane Process to Recover Heavy Hydrocarbons and to Remove Water from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    Kaaeid Lokhandwala

    2007-03-30

    The objective of this project was to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. An extended field test to demonstrate system performance under real-world high-pressure conditions was conducted to convince industry users of the efficiency and reliability of the process. The system was designed and fabricated by Membrane Technology and Research, Inc. (MTR) and installed and operated at BP Amoco's Pascagoula, MS plant. The Gas Research Institute partially supported the field demonstration and BP-Amoco helped install the unit and provide onsite operators and utilities. The gas processed by the membrane system meets pipeline specifications for dew point and BTU value and can be delivered without further treatment to the pipeline. During the course of this project, MTR has sold thirteen commercial units related to the field test technology. Revenue generated from new business is already more than four times the research dollars invested in this process by DOE. The process is ready for broader commercialization and the expectation is to pursue the commercialization plans developed during this project, including collaboration with other companies already servicing the natural gas processing industry.

  6. Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structural elements. [space shuttle aft body flap

    Science.gov (United States)

    Sheppard, C. H.; Hoggatt, J. T.; Symonds, W. A.

    1979-01-01

    The processing requirements for graphite/PMR-15 polyimide composites developed to demonstrate the structural integrity of polyimide composite structural elements at temperatures up to 589K (600 F) are described. Major tasks included: quality assurance development; materials and process development; specification verification; flat panel fabrication; stiffened panel fabrication; honeycomb panel fabrication; chopped fiber moldings; and demonstration component fabrication. Materials, processing, and quality assurance documents were prepared from experimentally derived data. Structural elements consisting of flat panels, corrugated stiffeners, I-beams, hat stiffeners, honeycomb panels, and chopped fiber moldings were made and tested. Property data from 219K (-65 F) to 589K (600 F) were obtained. All elements were made in a production environment. The size of each element was sufficient to insure production capability and structural component applicability. Problems associated with adhesive bonding, laminate and structural element analysis, material variability, and test methods were addressed.

  7. Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structural elements. [space shuttle aft body flap

    Science.gov (United States)

    Sheppard, C. H.; Hoggatt, J. T.; Symonds, W. A.

    1979-01-01

    The processing requirements for graphite/PMR-15 polyimide composites developed to demonstrate the structural integrity of polyimide composite structural elements at temperatures up to 589K (600 F) are described. Major tasks included: quality assurance development; materials and process development; specification verification; flat panel fabrication; stiffened panel fabrication; honeycomb panel fabrication; chopped fiber moldings; and demonstration component fabrication. Materials, processing, and quality assurance documents were prepared from experimentally derived data. Structural elements consisting of flat panels, corrugated stiffeners, I-beams, hat stiffeners, honeycomb panels, and chopped fiber moldings were made and tested. Property data from 219K (-65 F) to 589K (600 F) were obtained. All elements were made in a production environment. The size of each element was sufficient to insure production capability and structural component applicability. Problems associated with adhesive bonding, laminate and structural element analysis, material variability, and test methods were addressed.

  8. Analysis of Basis Weight Uniformity of Microfiber Nonwovens and Its Impact on Permeability and Filtration Properties

    Science.gov (United States)

    Amirnasr, Elham

    It is widely recognized that nonwoven basis weight non-uniformity affects various properties of nonwovens. However, few studies can be found in this topic. The development of uniformity definition and measurement methods and the study of their impact on various web properties such as filtration properties and air permeability would be beneficial both in industrial applications and in academia. They can be utilized as a quality control tool and would provide insights about nonwoven behaviors that cannot be solely explained by average values. Therefore, for quantifying nonwoven web basis weight uniformity we purse to develop an optical analytical tool. The quadrant method and clustering analysis was utilized in an image analysis scheme to help define "uniformity" and its spatial variation. Implementing the quadrant method in an image analysis system allows the establishment of a uniformity index that can be used to quantify the degree of uniformity. Clustering analysis has also been modified and verified using uniform and random simulated images with known parameters. Number of clusters and cluster properties such as cluster size, member and density was determined. We also utilized this new measurement method to evaluate uniformity of nonwovens produced with different processes and investigated impacts of uniformity on filtration and permeability. The results of quadrant method shows that uniformity index computed from quadrant method demonstrate a good range for non-uniformity of nonwoven webs. Clustering analysis is also been applied on reference nonwoven with known visual uniformity. From clustering analysis results, cluster size is promising to be used as uniformity parameter. It is been shown that non-uniform nonwovens has provide lager cluster size than uniform nonwovens. It was been tried to find a relationship between web properties and uniformity index (as a web characteristic). To achieve this, filtration properties, air permeability, solidity and

  9. Complete Demonstration.

    Science.gov (United States)

    Yelon, Stephen; Maddocks, Peg

    1986-01-01

    Describes four-step approach to educational demonstration: tell learners they will have to perform; what they should notice; describe each step before doing it; and require memorization of steps. Examples illustrate use of this process to demonstrate a general mental strategy, and industrial design, supervisory, fine motor, and specific…

  10. School Uniforms. Research Brief

    Science.gov (United States)

    Walker, Karen

    2007-01-01

    Does clothing make the person or does the person make the clothing? How does what attire a student wears to school affect their academic achievement? In 1996, President Clinton cited examples of school violence and discipline issues that might have been avoided had the students been wearing uniforms ("School uniforms: Prevention or suppression?").…

  11. Games Uniforms Unveiled

    Institute of Scientific and Technical Information of China (English)

    Linda

    2008-01-01

    The uniforms for Beijing Olympics’ workers, technical staff and volunteers have been unveiled to mark the 200-day countdown to the Games. The uniforms feature the key element of the clouds of promise and will be in three colors:red for Beijing Olympic Games Committee staff, blue

  12. Uniform magnesium oxide adsorbents

    Science.gov (United States)

    Dash, J. G.; Ecke, R.; Stoltenberg, J.; Vilches, O. E.; Whittemore, O. J., Jr.

    1978-01-01

    Kr adsorption on MgO is used to characterize the surface uniformity of MgO smoke and thermally decomposed Mg(OH)2. It is found that initially heterogeneous samples develop progressively sharper stepwise isotherms with increasingly-high-temperature heat treatment, apparently due to the removal of imperfections and high-energy facets, leaving surfaces of highly uniform (100) planes.

  13. Uniform-droplet spray forming

    Energy Technology Data Exchange (ETDEWEB)

    Blue, C.A.; Sikka, V.K. [Oak Ridge National Lab., TN (United States); Chun, Jung-Hoon [Massachusetts Institute of Technology, Cambridge, MA (United States); Ando, T. [Tufts Univ., Medford, MA (United States)

    1997-04-01

    The uniform-droplet process is a new method of liquid-metal atomization that results in single droplets that can be used to produce mono-size powders or sprayed-on to substrates to produce near-net shapes with tailored microstructure. The mono-sized powder-production capability of the uniform-droplet process also has the potential of permitting engineered powder blends to produce components of controlled porosity. Metal and alloy powders are commercially produced by at least three different methods: gas atomization, water atomization, and rotating disk. All three methods produce powders of a broad range in size with a very small yield of fine powders with single-sized droplets that can be used to produce mono-size powders or sprayed-on substrates to produce near-net shapes with tailored microstructures. The economical analysis has shown the process to have the potential of reducing capital cost by 50% and operating cost by 37.5% when applied to powder making. For the spray-forming process, a 25% savings is expected in both the capital and operating costs. The project is jointly carried out at Massachusetts Institute of Technology (MIT), Tuffs University, and Oak Ridge National Laboratory (ORNL). Preliminary interactions with both finished parts and powder producers have shown a strong interest in the uniform-droplet process. Systematic studies are being conducted to optimize the process parameters, understand the solidification of droplets and spray deposits, and develop a uniform-droplet-system (UDS) apparatus appropriate for processing engineering alloys.

  14. FIELD DEMONSTRATION OF A MEMBRANE PROCESS TO RECOVER HEAVY HYDROCARBONS AND TO REMOVE WATER FROM NATURAL GAS

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2002-04-10

    The objective of this project is to design, construct and field demonstrate a 3-MMscfd membrane system to recover natural gas liquids (NGL) and remove water from raw natural gas. The gas processed by the membrane system will meet pipeline specifications for dew point and Btu value, and the process is likely to be significantly less expensive than glycol dehydration followed by propane refrigeration, the principal competitive technology. The BP-Amoco gas processing plant in Pascagoula, MS was finalized as the location for the field demonstration. Detailed drawings of the MTR membrane skid (already constructed) were submitted to the plant in February, 2000. However, problems in reaching an agreement on the specifications of the system compressor delayed the project significantly, so MTR requested (and was subsequently granted) a no-cost extension to the project. Following resolution of the compressor issues, the goal is to order the compressor during the first quarter of 2002, and to start field tests in mid-2002. Information from potential users of the membrane separation process in the natural gas processing industry suggests that applications such as fuel gas conditioning and wellhead gas processing are the most promising initial targets. Therefore, most of our commercialization effort is focused on promoting these applications. Requests for stream evaluations and for design and price quotations have been received through MTR's web site, from direct contact with potential users, and through announcements in industry publications. To date, about 90 commercial quotes have been supplied, and orders totaling about $1.13 million for equipment or rental of membrane units have been received.

  15. An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring

    Directory of Open Access Journals (Sweden)

    Tien-Kan Chung

    2016-02-01

    Full Text Available An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers, criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence. Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.

  16. An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring.

    Science.gov (United States)

    Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

    2016-02-23

    An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.

  17. High-intensity drying processes: Impulse drying. Progress report on furnish evaluations for impulse drying commercialization demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Orloff, D.I.; Phelan, P.M.; Rudman, I.

    1995-02-01

    Laboratory and pilot scale experiments were performed to identify potential furnishes and operating parameters for upcoming high-speed pilot scale trials and commercial demonstration of impulse drying of heavy weight grades of paper. Results indicate that hydrodynamic specific surface is highly dependent on sheet formation and prehandling. Mill refined pulp and machine paper were comparable to laboratory prepared samples in regards to permeability and impulse drying. Process variables such as platen surface coating, felt type, felt moisture, and presteaming temperature profiles were investigated. Substantial improvements in sheet smoothness were achieved.

  18. Hydrogen production coupled to nuclear waste treatment: the safe treatment of alkali metals through a well-demonstrated process

    Energy Technology Data Exchange (ETDEWEB)

    Rahier, A. [Studie Centrum Voor Kernenergie (SCK-CEN), Boeretang, Mol (Belgium)]. E-mail: arahier@sckcen.be; Mesrobian, G. [Euro Chlor, Brussels (Belgium)]. E-mail: guy.mesrobian@wanadoo.fr

    2006-07-01

    In 1992, the United Nations emphasised the urgent need to act against the perpetuation of disparities between and within nations, the worsening of poverty, hunger, ill health and illiteracy and the continuing deterioration of ecosystems on which we depend for our well-being. In this framework, taking into account the preservation of both worldwide energy resources and ecosystems, the use of nuclear energy to produce clean energy carriers, such as hydrogen, is undoubtedly advisable. However, coping fully with the Agenda 21 statements requires defining adequate treatment processes for nuclear wastes. This paper discusses the possible use of a well-demonstrated process to convert radioactively contaminated alkali metals into sodium hydroxide while producing hydrogen. We conclude that a synergy between Chlor-Alkali specialists and nuclear specialists may help find an acceptable solution for radioactively contaminated sodium waste. (author)

  19. Extremely Preterm-Born Infants Demonstrate Different Facial Recognition Processes at 6-10 Months of Corrected Age.

    Science.gov (United States)

    Frie, Jakob; Padilla, Nelly; Ådén, Ulrika; Lagercrantz, Hugo; Bartocci, Marco

    2016-05-01

    To compare cortical hemodynamic responses to known and unknown facial stimuli between infants born extremely preterm and term-born infants, and to correlate the responses of the extremely preterm-born infants to regional cortical volumes at term-equivalent age. We compared 27 infants born extremely preterm (infrared spectroscopy. In the preterm group, we also performed structural brain magnetic resonance imaging and correlated regional cortical volumes to hemodynamic responses. The preterm-born infants demonstrated different cortical face recognition processes than the term-born infants. They had a significantly smaller hemodynamic response in the right frontotemporal areas while watching their mother's face (0.13 μmol/L vs 0.63 μmol/L; P recognition process compared with term-born infants. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Commercial-scale demonstration of the Liquid Phase Methanol process. Technical progress report number 8, April 1--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The project involves the construction of an 80,000 gallon per day (260 tons per day (TPD)) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. Originally tested at a small (10 TPD), DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology is being integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading.

  1. Uniformly Exponential Growth and Mapping Class Groups of Surfaces

    OpenAIRE

    Anderson, J. W.; Aramayona, J.; Shackleton, K.J.

    2005-01-01

    We show that the mapping class group (as well as closely related groups) of an orientable surface with finitely generated fundamental group has uniformly exponential growth. We further demonstrate the uniformly non-amenability of many of these groups.

  2. Field Demonstration of a Membrane Process to Separate Nitrogen from Natural Gas: Nineteenth Quarterly Progress Report (Second Quarter 2006)

    Energy Technology Data Exchange (ETDEWEB)

    Kaaeid Lokhandwala

    2006-06-30

    The original proposal described the construction and operation of a 1 MMscfd treatment system to be operated at a Butcher Energy gas field in Ohio. The gas produced at this field contained 17% nitrogen. During pre-commissioning of the project, a series of well tests showed that the amount of gas in the field was significantly smaller than expected and that the nitrogen content of the wells was very high (25 to 30%). After evaluating the revised cost of the project, Butcher Energy decided that the plant would not be economical and withdrew from the project. Since that time, Membrane Technology and Research, Inc. (MTR) signed a marketing and sales partnership with ABB Lummus Global, a large multinational corporation, and is working with the company's Randall Gas Technology group, a supplier of equipment and processing technology to the natural gas industry. Randall's engineering group found a new site for the project at a North Texas Exploration (NTE) gas processing plant, and we continue, but have as yet been unsuccessful in our attempts, to negotiate with Atmos Energy for a final test of the project demonstration unit. In the meantime, MTR has located an alternative testing opportunity and signed a contract for a demonstration plant in Rio Vista, CA. Several commercial sales have resulted from the partnership with ABB, and total sales of nitrogen/natural gas membrane separation units are now approaching $2.6 million.

  3. Metrological Needs for Monitoring Aquatic Environments: From the Demonstration of Metrological Traceability to the Decision Making Process

    Science.gov (United States)

    Lardy-Fontan, Sophie; Guigues, Nathalie; Lalere, Béatrice; Vaslin-Reimann, Sophie

    2014-08-01

    In Europe, the implementation of the Water Framework Directive WFD, in 2001, marks a strong standpoint. In addition to its objectives of a return to good chemical and good ecological status by the year 2015, it fixes the achievement of trends over space and time. The new requirements that arise from the WFD put considerable financial pressure on water management authorities. Because the overall decision-making process relies most of the time on acquired data, it puts considerable pressures on the display of high quality biological as well as chemical environmental measurements. However, performing measurements implies that i) the demonstration of their metrological traceability ii) the evidence of their achievement thanks to accurate and sensitive analytical methods and iii) their statement with a reliable estimate of expanded uncertainty is thoroughly addressed. Moreover, the measurement representativeness, especially in highly dynamic environment, is of prime interest in a context where comparability over space and time is needed. As a consequence, considerable challenges are dwelt on metrologists with great emphasis on parameters that are under regulation. This paper will discuss a panorama of the unavoidable metrological questions that have to be addressed: from the definition of the measurand to the final estimation of uncertainty; from the initial performances demonstration of methods to the final demonstration of mastery and capabilities through inter comparison laboratories and reference materials. A focus will be made on upcoming alternative monitoring approaches that are seldom addressed from a metrological point of view.

  4. Optimization of a micro-scale, high throughput process development tool and the demonstration of comparable process performance and product quality with biopharmaceutical manufacturing processes.

    Science.gov (United States)

    Evans, Steven T; Stewart, Kevin D; Afdahl, Chris; Patel, Rohan; Newell, Kelcy J

    2017-07-14

    In this paper, we discuss the optimization and implementation of a high throughput process development (HTPD) tool that utilizes commercially available micro-liter sized column technology for the purification of multiple clinically significant monoclonal antibodies. Chromatographic profiles generated using this optimized tool are shown to overlay with comparable profiles from the conventional bench-scale and clinical manufacturing scale. Further, all product quality attributes measured are comparable across scales for the mAb purifications. In addition to supporting chromatography process development efforts (e.g., optimization screening), comparable product quality results at all scales makes this tool is an appropriate scale model to enable purification and product quality comparisons of HTPD bioreactors conditions. The ability to perform up to 8 chromatography purifications in parallel with reduced material requirements per run creates opportunities for gathering more process knowledge in less time. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  5. One-pot synthesis of biocompatible Te-phenol formaldehyde resin core-shell nanowires with uniform size and unique fluorescent properties by a synergized soft-hard template process

    Energy Technology Data Exchange (ETDEWEB)

    Qian Haisheng; Zhu Enbo; Zheng Shunji; Yang Xingyun; Li Liangchao; Tong Guoxiu [Department of Chemistry, College of Chemistry and Life Science, Zhejiang Normal University, Jinhua 321004 (China); Li Zhengquan; Hu Yong; Guo Changfa [Institute of Physical Chemistry, Zhejiang Normal University, Jinhua 321004 (China); Guo Huichen, E-mail: shqian@zjnu.cn, E-mail: ghch-2004@hotmail.com [State Key Laboratory of Veterinary Etiological Biology and Key Laboratory of Animal Virology of Ministry of Agriculture, Lanzhou Veterinary Research Institute, Chinese Academy of Agricultural Sciences, Xujiaping 11, Lanzhou, Gansu 730046 (China)

    2010-12-10

    One-pot hydrothermal process has been developed to synthesize uniform Te-phenol formaldehyde resin core-shell nanowires with unique fluorescent properties. A synergistic soft-hard template mechanism has been proposed to explain the formation of the core-shell nanowires. The Te-phenol formaldehyde resin core-shell nanowires display unique fluorescent properties, which give strong luminescent emission in the blue-violet and green regions with excitation wavelengths of 270 nm and 402 nm, respectively.

  6. Demonstration of a TODGA based Extraction Process for the Partitioning of Minor Actinides from a PUREX Raffinate

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, D.; Christiansen, B.; Glatz, J.P.; Malmbeck, R.; Serrano-Purroy, D. [Commiss European Communities, Joint Res Ctr, Inst Transuranium Elements, D-76125 Karlsruhe, (Germany); Modolo, G. [Forschungszentrum Julich, Inst Energy Res Safety Res and Reactor Technol, D-52425 Julich, (Germany); Sorel, Ch. [Commissariat Energie Atom Valrho CEA, DRCP SCPS, F-30207 Bagnols Sur Ceze, (France); Magnusson, D. [Chalmers, Dept Chem and Biol Engn, S-41296 Gothenburg, (Sweden)

    2009-07-01

    Efficient recovery of minor actinides (MA) from genuine PUREX raffinate has been successfully demonstrated by the TODGA + TBP extractant mixture dissolved in an industrial aliphatic solvent TPH. The process was carried out in centrifugal contactors using an optimized flow-sheet involving a total of 32 stages, divided into 4 stages for extraction, 12 stages for scrubbing and 16 stages for back-extraction. Very high feed decontamination factors were obtained (Am, Cm 40 000) and the recovery of these elements was higher than 99.99%. Of the non-lanthanide fission products only Y and a small part of Ru were co-separated into the product fraction together with the lanthanides and the MA. (authors)

  7. Role and demonstration of structural integrity of LMFBR structures within the frame of the safety assessment process

    Energy Technology Data Exchange (ETDEWEB)

    Laue, H. (Siemens/KWU, Bergisch Gladbach (Germany)); Morgenstern, F. (Siemens/KWU, Bergisch Gladbach (Germany)); Rohdenburg, F. (Siemens/KWU, Bergisch Gladbach (Germany)); Hosemann, B. (Siemens/KWU, Bergisch Gladbach (Germany))

    1993-11-01

    The Structural Integrity DEmonstration Strategy (SIDES) has to satisfy two basic needs, namely to assure that the necessary safety precautions are fulfilled and to prove a well based safety and reliability argument for passive structures within the frame of the safety assessment process. The elements of this approach are related to five principles. The intention is to systematically compile all these elements for LMFBRs in order to assess the completeness, consistency and adequacy of the measures provided and to assure that their contribution to the plant's safety and reliability is adequate. The application of SIDES orientates itself on the three safety design levels, which could possibly result in a reclassification of events initiated by failures in passive structures such as leaks and breaks determined by the 'Lines of Defense' method. (orig.)

  8. Field Demonstration of a Membrane Process to Recover Heavy Hydrocarbons and to Remove Water from Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    Kaaeid Lokhandwala

    2003-09-29

    The objective of this project is to design, construct and field demonstrate a membrane system to recover natural gas liquids (NGLs) and remove water from raw natural gas. To convince industry users of the efficiency and reliability of the process, we plan to conduct an extended field test to demonstrate system performance under real-world conditions. The membrane system has been designed and fabricated by Membrane Technology and Research, Inc. (MTR). The MTR membrane system and the compressor are now onsite at BP's Pascagoula, MS plant. The plant is undergoing a very significant expansion and the installation of the membrane unit into the test location is being implemented, albeit at a slower rate than we expected. The startup of the system and conducting of tests will occur in the next six months, depending on the availability of the remaining budget. In the interim, significant commercial progress has been made regarding the introduction of the NGL membrane and systems into the natural gas market.

  9. Uniformly Convex Metric Spaces

    OpenAIRE

    Kell Martin

    2014-01-01

    In this paper the theory of uniformly convex metric spaces is developed. These spaces exhibit a generalized convexity of the metric from a fixed point. Using a (nearly) uniform convexity property a simple proof of reflexivity is presented and a weak topology of such spaces is analyzed. This topology called co-convex topology agrees with the usualy weak topology in Banach spaces. An example of a $CAT(0)$-spaces with weak topology which is not Hausdorff is given. This answers questions raised b...

  10. Demonstration Plant Equipment Design and Scale-Up from Pilot Plant of a Leaching and Solvent Extraction Process

    Directory of Open Access Journals (Sweden)

    Fátima Arroyo

    2015-05-01

    Full Text Available Germanium recovery from coal fly ash by hydrometallurgical procedures was studied at the pilot scale (5 kg of fly ash/h. Results were used to design the equipment of a demonstration-sized plant (200 kg of fly ash/h. The process is based on hydrometallurgical operations: firstly a germanium extraction from fly ash by leaching and a consequent Ge separation from the other elements present in the solution by solvent extraction procedures. Based on the experimental results, mass balances and McCabe-Thiele diagrams were applied to determine the number of steps of the solvent extraction stage. Different arrangements have been studied and a countercurrent process with three steps in extraction and six steps in elution was defined. A residence time of 5 min was fixed in both the extraction and elution stages. Volumetric ratios in extraction and stripping were: aqueous phase/organic phase = 5 and organic phase/stripping phase = 5, so a concentration factor of 25 is achieved. Mixers and decanters were completely defined. The maximum extracted and eluted germanium was estimated and a global efficiency of 94% was achieved. The cost-effectiveness of the equipment was estimated using the Lang factors.

  11. Demonstrating the effects of phonological similarity and frequency on item and order memory in Down syndrome using process dissociation.

    Science.gov (United States)

    Smith, Elizabeth; Jarrold, Christopher

    2014-12-01

    It is important to distinguish between memory for item information and memory for order information when considering the nature of verbal short-term memory (vSTM) performance. Although other researchers have attempted to make this distinction between item and order memory in children, none has done so using process dissociation. This study shows that such an approach can be particularly useful and informative. Individuals with Down syndrome (DS) tend to experience a vSTM deficit. These two experiments explored whether phonological similarity (Experiment 1) and item frequency (Experiment 2) affected vSTM for item and order information in a group of individuals with DS compared with typically developing (TD) vocabulary-matched children. Process dissociation was used to obtain measures of item and order memory via Nairne and Kelley's procedure (Journal of Memory and Language, 50 (2004) 113-133). Those with DS were poorer than the matched TD group for recall of both item and order information. However, in both populations, phonologically similar items reduced order memory but enhanced item memory, whereas high-frequency items resulted in improvements in both item and order memory-effects that are in line with previous research in the adult literature. These results indicate that, despite poorer vSTM performance in DS, individuals experience phonological coding of verbal input and a contribution of long-term memory knowledge to recall. These findings inform routes for interventions for those with DS, highlighting the need to enhance both item and order memory. Moreover, this work demonstrates that process dissociation is applicable and informative for studying special populations and children.

  12. Uniform random number generators

    Science.gov (United States)

    Farr, W. R.

    1971-01-01

    Methods are presented for the generation of random numbers with uniform and normal distributions. Subprogram listings of Fortran generators for the Univac 1108, SDS 930, and CDC 3200 digital computers are also included. The generators are of the mixed multiplicative type, and the mathematical method employed is that of Marsaglia and Bray.

  13. Testing for uniformity in multidimensional data.

    Science.gov (United States)

    Smith, S P; Jain, A K

    1984-01-01

    Testing for uniformity in multidimensional data is important in exploratory pattern analysis, statistical pattern recognition, and image processing. The goal of this paper is to determine whether the data follow the uniform distribution over some compact convex set in K-dimensional space, called the sampling window. We first provide a simple, computationally efficient method for generating a uniformly distributed sample over a set which approximates the convex hul of the data. We then test for uniformity by comparing this generated sample to the data by using Friedman-Rafsky's minimal spanning tree (MST) based test. Experiments with both simulated and real data indicate that this MST-based test is useful in deciding if data are uniform.

  14. Deposition uniformity inspection in IC wafer surface

    Science.gov (United States)

    Li, W. C.; Lin, Y. T.; Jeng, J. J.; Chang, C. L.

    2014-03-01

    This paper focuses on the task of automatic visual inspection of color uniformity on the surface of integrated circuits (IC) wafers arising from the layering process. The oxide thickness uniformity within a given wafer with a desired target thickness is of great importance for modern semiconductor circuits with small oxide thickness. The non-uniform chemical vapor deposition (CVD) on a wafer surface will proceed to fail testing in Wafer Acceptance Test (WAT). Early detection of non-uniform deposition in a wafer surface can reduce material waste and improve production yields. The fastest and most low-priced inspection method is a machine vision-based inspection system. In this paper, the proposed visual inspection system is based on the color representations which were reflected from wafer surface. The regions of non-uniform deposition present different colors from the uniform background in a wafer surface. The proposed inspection technique first learns the color data via color space transformation from uniform deposition of normal wafer surfaces. The individual small region statistical comparison scheme then proceeds to the testing wafers. Experimental results show that the proposed method can effectively detect the non-uniform deposition regions on the wafer surface. The inspection time of the deposited wafers is quite compatible with the atmospheric pressure CVD time.

  15. Develop and demonstrate manufacturing processes for fabricating graphite filament reinforced polymide (Gr/PI) composite structural elements

    Science.gov (United States)

    Chase, V. A.; Harrison, E. S.

    1985-01-01

    A study was conducted to assess the merits of using graphite/polyimide, NR-150B2 resin, for structural applications on advanced space launch vehicles. The program was divided into two phases: (1) Fabrication Process Development; and (2) Demonstration Components. The first phase of the program involved the selection of a graphite fiber, quality assurance of the NR-150B2 polyimide resin, and the quality assurance of the graphite/polyimide prepreg. In the second phase of the program, a limited number of components were fabricated before the NR-150B2 resin system was removed from the market by the supplier, Du Pont. The advancement of the NR-150B2 polyimide resin binder was found to vary significantly based on previous time and temperature history during the prepregging operation. Strength retention at 316C (600F) was found to be 50% that of room temperature strength. However, the composite would retain its initial strength after 200 hours exposure at 316C (600F). Basic chemistry studies are required for determining NR-150B2 resin binder quality assurance parameters. Graphite fibers are available that can withstand high temperature cure and postcure cycles.

  16. Optimization of process parameters in a large-area hot-wire CVD reactor for the deposition of amorphous silicon (a-Si:H) for solar cell application with highly uniform material quality

    Energy Technology Data Exchange (ETDEWEB)

    Pflueger, A.; Mukherjee, C.; Schroeder, B. [Department of Physics, Center of Materials Science, University of Kaiserslautern, P.O. Box 3049, D-67653 Kaiserslautern (Germany)

    2002-07-01

    Scale-up of a-Si:H-based thin film applications such as solar cells, entirely or partly prepared by hot-wire chemical vapor deposition (HWCVD), requires research on the deposition process in a large-area HWCVD system. The influence of gas supply and filament geometry on thickness uniformity has already been reported, but their influence on material quality is systematically studied for the first time. The optimization of deposition parameters for obtaining best material quality in our large-area HWCVD system resulted in an optimum filament temperature, T{sub fil}{approx}1600C, pressure, p=8mTorr and silane flow, F(SiH{sub 4})=100sccm, keeping the substrate temperature at T{sub S}=200C. A special gas supply (gas shower with tiny holes of uniform size) and a filament grid, consisting of six filaments with an interfilament distance, d{sub fil}=4cm were used. The optimum filament-to-substrate distance was found to be d{sub fil-S}=8.4cm. While studying the influence of different d{sub fil} and gas supply configurations on the material quality, the above-mentioned setup and parameters yield best results for both uniformity and material quality. With the setup mentioned, we could achieve device quality a-Si:H films with a thickness uniformity of {+-}2.5% on a circular area of 20cm in diameter. The material, grown at a deposition rate of r{sub d}{approx}4A/s, was characterized on nine positions of the 30cmx30cm substrate area, and revealed reasonable uniformity of the opto-electronic properties, e.g photosensitivity, {sigma}{sub Ph}/{sigma}{sub D}=(2.46{+-}0.7)x10{sup 5}, microstructure factor, R=0.17{+-}0.05, defect densities, N{sub d(PDS)}=(2.06{+-}0.6)x10{sup 17}cm{sup -3} and N{sub d(CPM)}=(2.05{+-}0.5)x10{sup 16}cm{sup -3} (film properties are given as mean values and standard deviations). Finally, we fabricated pin solar cells, with the i-layer deposited on small-area p-substrates distributed over an area of 20cmx20cm in this large-area deposition system, and

  17. Optimization of the enzymatic saccharification process conditions of cowpea beverage with uniform design method%豇豆饮料糖化工艺的优化

    Institute of Scientific and Technical Information of China (English)

    高愿军; 石瑞华; 詹现璞; 唐艳红; 路源

    2012-01-01

    通过单因素和均匀试验,对豇豆饮料加工中葡萄糖淀粉酶酶解最佳工艺条件进行研究.结果表明,豇豆浆液经α淀粉酶液化后,最佳糖化条件:葡萄糖淀粉酶添加0.15%,pH为4.2,60 ℃条件下反应3.5h.访工艺条件生产的豇豆饮料色泽鲜亮,口感细腻.%By using univariale and uniform design experiment, the optimum conditions for the glucoamylase enzymatic hydrolysis of the cowpea heverage are studied in this article. The results showed that, the best sacchanfication conditions were : after liquefying by α-amyl-ase, 0. 15% glucoamylase were added into cowpea serous, reacted 3. 5 h under the conditions of pH 4. 2 and temperature 60℃. The cowpea drinks have bright color and delicate taste by the technology.

  18. Demonstrating the Qualitative Differences between Semantic Aphasia and Semantic Dementia: A Novel Exploration of Nonverbal Semantic Processing

    Directory of Open Access Journals (Sweden)

    Krist A. Noonan

    2013-01-01

    Full Text Available Semantic dementia (SD implicates the anterior temporal lobes (ATL as a critical substrate for semantic memory. Multi-modal semantic impairment can also be a feature of post-stroke aphasia (referred to here as “semantic aphasia” or SA where patients show impaired regulatory control accompanied by lesions to the frontal and/or temporo-parietal cortices, and thus the two patient groups demonstrate qualitatively different patterns of semantic impairment [1]. Previous comparisons of these two patient groups have tended to focus on verbal receptive tasks. Accordingly, this study investigated nonverbal receptive abilities via a comparison of reality decision judgements in SD and SA. Pictures of objects were presented alongside non-real distracters whose features were altered to make them more/less plausible for the semantic category. The results highlighted a number of critical differences between the two groups. Compared to SD patients, SA patients: (1 were relatively unimpaired on the two alternative forced choice (2AFC decisions despite showing a comparable degree of semantic impairment on other assessments; (2 showed minimal effects of the plausibility manipulation; (3 were strongly influenced by variations in the regulatory requirements of tasks; and (4 exhibited a reversed effect of familiarity–i.e., better performance on less commonly encountered items. These results support a distinction between semantic impairments which arise from impaired regulatory processes (e.g., SA versus those where degraded semantic knowledge is the causal factor (e.g., SD. SA patients performed relatively well because the task structure reduced the requirement for internally generated control. In contrast, SD patients performed poorly because their degraded knowledge did not allow the fine-grained distinctions required to complete the task.

  19. Requalification of the 235-F Metallograph Facility gloveboxes for use in the 773-A Pre-Processing/Re-Processing Laboratory and plutonium ``Can in Can`` demonstrations

    Energy Technology Data Exchange (ETDEWEB)

    Hinds, S.; Hidlay, J.

    1997-04-16

    The proposed use for these gloveboxes are: (1) to utilize the Pu metal glovebox system for the primary containment associated with the Pre-Processing/Re-Processing Laboratory for obtaining radioactive glass compound viscometer analysis, and (2) to utilize the Pu oxide glovebox system for primary containment associated with the Pu Can in Can Demonstration for proof of principle testing specific to long term Pu immobilization and storage technology. This report presents objective evidence that supports the engineering judgment indicating the existing gloveboxes can be requalified for the proposed uses indicated above. SRS has the ability to duplicate the test parameters, with site forces, that will meet or exceed the identical acceptance criteria established to qualify the existing gloveboxes. The qualification effort will be a documented procedure using the leak test criteria characteristic of the original glovebox purchase. Two equivalent tests will be performed, one for post modification leak test acceptance and one for post installation leak test acceptance. Assurance of this approach is substantiated by thorough reviews of glovebox, leak test and weld standard guidance documents, as well as review of historical Project 3253 design and vendor information specific to the existing gloveboxes. Reuse of these gloveboxes will eliminate the need for competitive procurement of new gloveboxes.

  20. Impact of the freeze-drying process on product appearance, residual moisture content, viability, and batch uniformity of freeze-dried bacterial cultures safeguarded at culture collections.

    Science.gov (United States)

    Peiren, Jindrich; Hellemans, Ann; De Vos, Paul

    2016-07-01

    In this study, causes of collapsed bacterial cultures in glass ampoules observed after freeze-drying were investigated as well as the influence of collapse on residual moisture content (RMC) and viability. Also, the effect of heat radiation and post freeze-drying treatments on the RMC was studied. Cake morphologies of 21 bacterial strains obtained after freeze-drying with one standard protocol could be classified visually into four major types: no collapse, porous, partial collapse, and collapse. The more pronounced the collapse, the higher residual moisture content of the freeze-dried product, ranging from 1.53 % for non-collapsed products to 3.62 % for collapsed products. The most important cause of collapse was the mass of the inserted cotton plug in the ampoule. Default cotton plugs with a mass between 21 and 30 mg inside the ampoule did not affect the viability of freeze-dried Aliivibrio fischeri LMG 4414(T) compared to ampoules without cotton plugs. Cotton plugs with a mass higher than 65 mg inside the ampoule induced a full collapsed product with rubbery look (melt-back) and decreasing viability during storage. Heat radiation effects in the freeze-drying chamber and post freeze-drying treatments such as exposure time to air after freeze-drying and manifold drying time prior to heat sealing of ampoules influenced the RMC of freeze-dried products. To produce uniform batches of freeze-dried bacterial strains with intact cake structures and highest viabilities, inserted cotton plugs should not exceed 21 mg per ampoule. Furthermore, heat radiation effects should be calculated in the design of the primary drying phase and manifold drying time before heat sealing should be determined as a function of exposure time to air.

  1. Collocation on uniform grids

    Energy Technology Data Exchange (ETDEWEB)

    Amore, Paolo; Saenz, Ricardo A; Salvo, Koen [Facultad de Ciencias, CUICBAS, Universidad de Colima, Bernal DIaz del Castillo 340 Colima, Colima (Mexico); Fernandez, Francisco M [INIFTA (UNLP, CCT La Plata-Conicet), Diag. 113 y 64 S/N, Sucursal 4, Casilla de Correo 16, 1900 La Plata (Argentina)], E-mail: paolo.amore@gmail.com, E-mail: fernande@quimica.unlp.edu.ar, E-mail: rasaenz@ucol.mx, E-mail: koen.salvo@gmail.com

    2009-03-20

    In this paper we derive four sets of sinc-like functions, defined on a finite interval and obeying different boundary conditions. The functions in each set are orthogonal and their nodes are uniformly distributed on the interval. We have applied each set to solve a large class of eigenvalue equations, with different boundary conditions, both on finite intervals and on the real line, showing that precise numerical results can be obtained efficiently and rapidly. A comparison with results available in the literature is also performed.

  2. Women in service uniforms

    Directory of Open Access Journals (Sweden)

    Hanna Karaszewska

    2012-12-01

    Full Text Available The article discusses the problems of women who work in the uniformed services with the particular emphasis on the performing of the occupation of the prison service. It presents the legal issues relating to equal treatment of men and women in the workplace, formal factors influencing their employment, the status of women in prison, and the problems of their conducting in the professional role. The article also presents the results of research conducted in Poland and all over the world, on the functioning of women in prison and their relations with officers of the Prison Service, as well as with inmates.

  3. The uniform electron gas

    CERN Document Server

    Loos, Pierre-François

    2016-01-01

    The uniform electron gas or UEG (also known as jellium) is one of the most fundamental models in condensed-matter physics and the cornerstone of the most popular approximation --- the local-density approximation --- within density-functional theory. In this article, we provide a detailed review on the energetics of the UEG at high, intermediate and low densities, and in one, two and three dimensions. We also report the best quantum Monte Carlo and symmetry-broken Hartree-Fock calculations available in the literature for the UEG and discuss the phase diagrams of jellium.

  4. Uniform gradient expansions

    Directory of Open Access Journals (Sweden)

    Massimo Giovannini

    2015-06-01

    Full Text Available Cosmological singularities are often discussed by means of a gradient expansion that can also describe, during a quasi-de Sitter phase, the progressive suppression of curvature inhomogeneities. While the inflationary event horizon is being formed the two mentioned regimes coexist and a uniform expansion can be conceived and applied to the evolution of spatial gradients across the protoinflationary boundary. It is argued that conventional arguments addressing the preinflationary initial conditions are necessary but generally not sufficient to guarantee a homogeneous onset of the conventional inflationary stage.

  5. Uniform distribution of sequences

    CERN Document Server

    Kuipers, L

    2006-01-01

    The theory of uniform distribution began with Hermann Weyl's celebrated paper of 1916. In later decades, the theory moved beyond its roots in diophantine approximations to provide common ground for topics as diverse as number theory, probability theory, functional analysis, and topological algebra. This book summarizes the theory's development from its beginnings to the mid-1970s, with comprehensive coverage of both methods and their underlying principles.A practical introduction for students of number theory and analysis as well as a reference for researchers in the field, this book covers un

  6. Uniform gradient expansions

    Energy Technology Data Exchange (ETDEWEB)

    Giovannini, Massimo, E-mail: massimo.giovannini@cern.ch [Department of Physics, Theory Division, CERN, 1211 Geneva 23 (Switzerland); INFN, Section of Milan-Bicocca, 20126 Milan (Italy)

    2015-06-30

    Cosmological singularities are often discussed by means of a gradient expansion that can also describe, during a quasi-de Sitter phase, the progressive suppression of curvature inhomogeneities. While the inflationary event horizon is being formed the two mentioned regimes coexist and a uniform expansion can be conceived and applied to the evolution of spatial gradients across the protoinflationary boundary. It is argued that conventional arguments addressing the preinflationary initial conditions are necessary but generally not sufficient to guarantee a homogeneous onset of the conventional inflationary stage.

  7. Influence of relative rolling reduction and thickness layers bimetallic plate at the non-uniformity of the strain after rolling process

    Science.gov (United States)

    Rydz, D.; Stradomski, G.; Dyja, H.

    2017-02-01

    In the article were made numerical and laboratory tests of two-layers rolling process sheet composed of Al99,8 + M1E. Laboratory tests made with use of 150 mm diameter working rolls mill. To the modeling of the bimetallic plate rolling were taken the FEM Forge 2D software based on the theory of plasticity and MathCad program (in which to the rolling process modeling were used the mathematical model developed in the work [5] based on the theory of viscoelasticity). The aim of study was to determine the influence of layer thickness HT0/HM0 and relative deformation ε on the uneven distribution of steel sheet deformation after rolling process. Calculations based on the theory of viscoelasticity allowed additionally take into account the impact of the delayed effects of the variation of viscoelastic deformation of layers of the bimetallic plate rolling process.

  8. Application of CRAFT (Complete Reduction to Amplitude Frequency Table) in non-uniformly sampled (NUS) two-dimensional NMR data processing.

    Science.gov (United States)

    Krishnamurthy, Krish; Hari, Natarajan

    2017-09-15

    The recently published CRAFT (Complete Reduction to Amplitude Frequency Table) technique converts the raw FID data (i.e., time domain data) into a table of frequencies, amplitudes, decay rate constants and phases. It offers an alternate approach to decimate time-domain data, with minimal pre-processing step. It has been shown that application of CRAFT technique to process the t1 dimension of the 2D data, significantly improved the detectable resolution by it ability to analyze without the use of ubiquitous apodization of extensively zero-filled data. It was noted earlier that CRAFT did not resolve sinusoids that were not already resolvable in time-domain (i.e., t1 max dependent resolution). We present a combined NUS-IST-CRAFT approach wherein the NUS acquisition technique (sparse sampling technique) increases the intrinsic resolution in time-domain (by increasing t1 max), IST fills the gap in the sparse sampling, and CRAFT processing extracts the information without loss due to any severe apodization. NUS and CRAFT are thus complementary techniques to improve intrinsic and usable resolution. We show that significant improvement can be achieved with this combination over conventional NUS-IST processing. With reasonable sensitivity, the models can be extended to significantly higher t1 max to generate an indirect-DEPT spectrum that rivals the direct observe counterpart. This article is protected by copyright. All rights reserved.

  9. Uniform Exponential Growth in Algebras /

    OpenAIRE

    Briggs, Christopher Alan

    2013-01-01

    We consider uniform exponential growth in algebras. We give conditions for the uniform exponential growth of descending-filtered algebras and prove that an N-graded algebra has uniform exponential growth if it has exponential growth. We use this to prove that Golod- Shafarevich algebras and group algebras of Golod- Shafarevich groups have uniform exponential growth. We prove that the twisted Laurent extension of a free commutative polynomial algebra with respect to an endomorphism with some e...

  10. Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph C

    Science.gov (United States)

    1981-01-01

    Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control methods, and the fabrication of Space Shuttle composite structure components is reported. The formulation and processing limits for three batches of resin are presented. Process improvements for simplification of the imidizing and autoclave cure cycles are described. Imidized and autoclave cured test panels were prepared. Celion/LARC-160 cure process verification and the fabrication of honeycomb sandwich panel elements and skin/stringer panels are described. C-scans of laminates imidized at 163 C to 218 C for periods from 30 to 180 minutes, and of process verification laminates made from different batches of prepreg are presented. Failure modes and load/strain characteristics of sandwich elements and C-scans of stringer to skin bond joints are also given.

  11. Modulated grayscale UV pattern for uniform photopolymerization based on a digital micromirror device system

    Science.gov (United States)

    Yoon, Jinsik; Kim, Kibeom; Park, Wook

    2017-07-01

    We present an essential method for generating microparticles uniformly in a single ultraviolet (UV) light exposure area for optofluidic maskless lithography. In the optofluidic maskless lithography process, the productivity of monodisperse microparticles depends on the size of the UV exposure area. An effective fabrication area is determined by the size of the UV intensity profile map, satisfying the required uniformity of UV intensity. To increase the productivity of monodisperse microparticles in optofluidic maskless lithography, we expanded the effective UV exposure area by modulating the intensity of the desired UV light pattern based on the premeasured UV intensity profile map. We verified the improvement of the uniformity of the microparticles generated by the proposed modulation technique, providing histogram analyses of the conjugated fluorescent intensities and the sizes of the microparticles. Additionally, we demonstrated the generation of DNA uniformly encapsulated in microparticles.

  12. Should School Nurses Wear Uniforms?

    Science.gov (United States)

    Journal of School Health, 2001

    2001-01-01

    This 1958 paper questions whether school nurses should wear uniforms (specifically, white uniforms). It concludes that white uniforms are often associated with the treatment of ill people, and since many people have a fear reaction to them, they are not necessary and are even undesirable. Since school nurses are school staff members, they should…

  13. The Uniform Rugosity Effect

    Science.gov (United States)

    Bonnivard, Matthieu; Bucur, Dorin

    2012-06-01

    Relying on the effect of microscopic asperities, one can mathematically justify that viscous fluids adhere completely on the boundary of an impermeable domain. The rugosity effect accounts asymptotically for the transformation of complete slip boundary conditions on a rough surface in total adherence boundary conditions, as the amplitude of the rugosities vanishes. The decreasing rate (average velocity divided by the amplitude of the rugosities) computed on close flat layers is definitely influenced by the geometry. Recent results prove that this ratio has a uniform upper bound for certain geometries, like periodical and "almost Lipschitz" boundaries. The purpose of this paper is to prove that such a result holds for arbitrary (non-periodical) crystalline boundaries and general (non-smooth) periodical boundaries.

  14. Uniform quantized electron gas

    Science.gov (United States)

    Høye, Johan S.; Lomba, Enrique

    2016-10-01

    In this work we study the correlation energy of the quantized electron gas of uniform density at temperature T  =  0. To do so we utilize methods from classical statistical mechanics. The basis for this is the Feynman path integral for the partition function of quantized systems. With this representation the quantum mechanical problem can be interpreted as, and is equivalent to, a classical polymer problem in four dimensions where the fourth dimension is imaginary time. Thus methods, results, and properties obtained in the statistical mechanics of classical fluids can be utilized. From this viewpoint we recover the well known RPA (random phase approximation). Then to improve it we modify the RPA by requiring the corresponding correlation function to be such that electrons with equal spins can not be on the same position. Numerical evaluations are compared with well known results of a standard parameterization of Monte Carlo correlation energies.

  15. Optimization of microwave processing procedure of semen raphani by uniform-design%均匀设计优选莱菔子微波炮制工艺

    Institute of Scientific and Technical Information of China (English)

    李彦博; 孙静

    2011-01-01

    目的 优选莱菔子微波炮制的最佳工艺.方法 以微波火力和加热时间为变量,采用均匀实验设计,以外观性状、水溶性浸出物、醇溶性浸出物、脂肪油和芥子碱硫氰酸盐含量为考察指标.结果 莱菔子微波炮制的最佳工艺为微波大火力,加热3 min.结论 微波法炮制莱菔子合理、稳定、可行.%Objective To select the best microwave processing procedure of semen raphani. Methods The u-niform-design was used with the variables of microwave power and heating time, on the basis of the indexes of macro-scopical character, water-soluble extractives, ethanol-soluble extractives, fatty oil content and Sinapine thiocyanate content. Results The best microwave process of semen raphani was strong microwave power and heating for 3 min. Conclusion The Microwave processing procedure of semen raphani is proved to be reasonable, stable and feasible.

  16. Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph B

    Science.gov (United States)

    1981-01-01

    Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control, and the fabrication of Space Shuttle composite structure components is reported. Liquid chromatographic analyses of three repeatibility batches were performed and are compared to previous Hexcel standard production and to variables study LARC-160 intermediate resins. Development of processes for chopped fiber molding are described and flexural strength, elastic modulus, and other physical and mechanical properties of the molding are presented.

  17. Demonstration of an approach to waste form qualification through simulation of liquid-fed ceramic melter process operations

    Energy Technology Data Exchange (ETDEWEB)

    Reimus, P.W.; Kuhn, W.L.; Peters, R.D.; Pulsipher, B.A.

    1986-07-01

    During fiscal year 1982, the US Department of Energy (DOE) assigned responsibility for managing civilian nuclear waste treatment programs in the United States to the Nuclear Waste Treatment Program (NWTP) at the Pacific Northwest Laboratory (PNL). One of the principal objectives of this program is to establish relationships between vitrification process control and glass quality. Users of the liquid-fed ceramic melter (LFCM) process will need such relationships in order to establish acceptance of vitrified high-level nuclear waste at a licensed federal repository without resorting to destructive examination of the canisters. The objective is to be able to supply a regulatory agency with an estimate of the composition, durability, and integrity of the glass in each waste glass canister produced from an LFCM process simply by examining the process data collected during the operation of the LFCM. The work described here will continue through FY-1987 and culminate in a final report on the ability to control and monitor an LFCM process through sampling and process control charting of the LFCM feed system.

  18. On fixed points and uniformly convex spaces

    OpenAIRE

    Gelander, Tsachik

    2008-01-01

    The purpose of this note is to present two elementary, but useful, facts concerning actions on uniformly convex spaces. We demonstrate how each of them can be used in an alternative proof of the triviality of the first $L_p$-cohomology of higher rank simple Lie groups, proved in [BFGM].

  19. Demonstrating the Effects of Processing on the Structure and Physical Properties of Plastic Using Disposable PETE Cups

    Science.gov (United States)

    Erk, Kendra A.; Rhein, Morgan; Krafcik, Matthew J.; Ydstie, Sophie

    2015-01-01

    An educational activity is described in which the structure and physical properties of disposable plastic cups were directly related to the method of processing. The mechanical properties of specimens cut from the walls of poly(ethylene terephthalate) (PETE) cups, oriented parallel and perpendicular to the thermoforming direction, were measured in…

  20. A complete process for production of flexible large area polymer solar cells entirely using screen printing-First public demonstration

    DEFF Research Database (Denmark)

    Krebs, Frederik C; Jørgensen, Mikkel; Norrman, Kion;

    2009-01-01

    , complete processing in air using commonly available screen printing, and finally, simple mechanical encapsulation using a flexible packaging material and electrical contacting post-production using crimped contacts. We detail the production of more than 2000 modules in one production run and show...

  1. GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATION OF THE DWPF CHEMICAL PROCESS CELL WITH SLUDGE AND SUPERNATE SIMULANTS

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Stone, M.; Newell, J.; Best, D.; Zamecnik, J.

    2012-08-28

    Savannah River Remediation (SRR) is evaluating changes to its current Defense Waste Processing Facility (DWPF) flowsheet to improve processing cycle times. This will enable the facility to support higher canister production while maximizing waste loading. Higher throughput is needed in the Chemical Process Cell (CPC) since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the DWPF gas chromatographs (GC) and the potential for production of flammable quantities of hydrogen, reducing or eliminating the amount of formic acid used in the CPC is being developed. Earlier work at Savannah River National Laboratory has shown that replacing formic acid with an 80:20 molar blend of glycolic and formic acids has the potential to remove mercury in the SRAT without any significant catalytic hydrogen generation. This report summarizes the research completed to determine the feasibility of processing without formic acid. In earlier development of the glycolic-formic acid flowsheet, one run (GF8) was completed without formic acid. It is of particular interest that mercury was successfully removed in GF8, no formic acid at 125% stoichiometry. Glycolic acid did not show the ability to reduce mercury to elemental mercury in initial screening studies, which is why previous testing focused on using the formic/glycolic blend. The objective of the testing detailed in this document is to determine the viability of the nitric-glycolic acid flowsheet in processing sludge over a wide compositional range as requested by DWPF. This work was performed under the guidance of Task Technical and Quality Assurance Plan (TT&QAP). The details regarding the simulant preparation and analysis have been documented previously.

  2. A uniform LMI formulation for tuning PID, multi-term fractional-order PID, and Tilt-Integral-Derivative (TID) for integer and fractional-order processes.

    Science.gov (United States)

    Merrikh-Bayat, Farshad

    2017-03-15

    In this paper first the Multi-term Fractional-Order PID (MFOPID) whose transfer function is equal to [Formula: see text] , where kj and αj are unknown and known real parameters respectively, is introduced. Without any loss of generality, a special form of MFOPID with transfer function kp+ki/s+kd1s+kd2s(μ) where kp, ki, kd1, and kd2 are unknown real and μ is a known positive real parameter, is considered. Similar to PID and TID, MFOPID is also linear in its parameters which makes it possible to study all of them in a same framework. Tuning the parameters of PID, TID, and MFOPID based on loop shaping using Linear Matrix Inequalities (LMIs) is discussed. For this purpose separate LMIs for closed-loop stability (of sufficient type) and adjusting different aspects of the open-loop frequency response are developed. The proposed LMIs for stability are obtained based on the Nyquist stability theorem and can be applied to both integer and fractional-order (not necessarily commensurate) processes which are either stable or have one unstable pole. Numerical simulations show that the performance of the four-variable MFOPID can compete the trivial five-variable FOPID and often excels PID and TID.

  3. Processing of Ni30Pt20Ti50 High-Temperature Shape-Memory Alloy Into Thin Rod Demonstrated

    Science.gov (United States)

    Noebe, Ronald D.; Draper, Susan L.; Biles, Tiffany A.; Leonhardt, Todd

    2005-01-01

    High-temperature shape-memory alloys (HTSMAs) based on nickel-titanium (NiTi) with significant ternary additions of palladium (Pd), platinum (Pt), gold (Au), or hafnium (Hf) have been identified as potential high-temperature actuator materials for use up to 500 C. These materials provide an enabling technology for the development of "smart structures" used to control the noise, emissions, or efficiency of gas turbine engines. The demand for these high-temperature versions of conventional shape-memory alloys also has been growing in the automotive, process control, and energy industries. However these materials, including the NiPtTi alloys being developed at the NASA Glenn Research Center, will never find widespread acceptance unless they can be readily processed into useable forms.

  4. Tested Demonstrations.

    Science.gov (United States)

    Sands, Robert; And Others

    1982-01-01

    Procedures for two demonstrations are provided. The solubility of ammonia gas in water is demonstrated by introducing water into a closed can filled with the gas, collapsing the can. The second demonstration relates scale of standard reduction potentials to observed behavior of metals in reactions with hydrogen to produce hydrogen gas. (Author/JN)

  5. Assessment indices for uniform and non-uniform thermal environments

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Different assessment indices for thermal environments were compared and selected for proper assessment of indoor thermal environments.30 subjects reported their overall thermal sensation,thermal comfort,and thermal acceptability in uniform and non-uniform conditions.The results show that these three assessment indices provide equivalent evaluations in uniform environments.However,overall thermal sensation differs from the other two indices and cannot be used as a proper index for the evaluation of non-uniform environments.The relationship between the percentage and the mean vote for each index is established.

  6. Uniform Sampling Table Method and its Applications II--Evaluating the Uniform Sampling by Experiment.

    Science.gov (United States)

    Chen, Yibin; Chen, Jiaxi; Chen, Xuan; Wang, Min; Wang, Wei

    2015-01-01

    A new method of uniform sampling is evaluated in this paper. The items and indexes were adopted to evaluate the rationality of the uniform sampling. The evaluation items included convenience of operation, uniformity of sampling site distribution, and accuracy and precision of measured results. The evaluation indexes included operational complexity, occupation rate of sampling site in a row and column, relative accuracy of pill weight, and relative deviation of pill weight. They were obtained from three kinds of drugs with different shape and size by four kinds of sampling methods. Gray correlation analysis was adopted to make the comprehensive evaluation by comparing it with the standard method. The experimental results showed that the convenience of uniform sampling method was 1 (100%), odds ratio of occupation rate in a row and column was infinity, relative accuracy was 99.50-99.89%, reproducibility RSD was 0.45-0.89%, and weighted incidence degree exceeded the standard method. Hence, the uniform sampling method was easy to operate, and the selected samples were distributed uniformly. The experimental results demonstrated that the uniform sampling method has good accuracy and reproducibility, which can be put into use in drugs analysis.

  7. GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATION OF THE DWPF CHEMICAL PROCESSING CELL WITH MATRIX SIMULANTS AND SUPERNATE

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Stone, M.; Newell, J.; Best, D.

    2012-05-07

    Savannah River Remediation (SRR) is evaluating changes to its current DWPF flowsheet to improve processing cycle times. This will enable the facility to support higher canister production while maximizing waste loading. Higher throughput is needed in the CPC since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the DWPF gas chromatographs (GC) and the potential for production of flammable quantities of hydrogen, reducing or eliminating the amount of formic acid used in the CPC is being developed. Earlier work at Savannah River National Laboratory has shown that replacing formic acid with an 80:20 molar blend of glycolic and formic acids has the potential to remove mercury in the SRAT without any significant catalytic hydrogen generation. This report summarizes the research completed to determine the feasibility of processing without formic acid. In earlier development of the glycolic-formic acid flowsheet, one run (GF8) was completed without formic acid. It is of particular interest that mercury was successfully removed in GF8, no formic acid at 125% stoichiometry. Glycolic acid did not show the ability to reduce mercury to elemental mercury in initial screening studies, which is why previous testing focused on using the formic/glycolic blend. The objective of the testing detailed in this document is to determine the viability of the nitric-glycolic acid flowsheet in processing sludge over a wide compositional range as requested by DWPF. This work was performed under the guidance of Task Technical and Quality Assurance Plan (TT and QAP). The details regarding the simulant preparation and analysis have been documented previously.

  8. Lab-scale demonstration of recuperative thickening technology for enhanced biogas production and dewaterability in anaerobic digestion processes.

    Science.gov (United States)

    Cobbledick, Jeffrey; Aubry, Nicholas; Zhang, Victor; Rollings-Scattergood, Sasha; Latulippe, David R

    2016-05-15

    There is growing interest in the use of high performance anaerobic digestion (AD) processes for the production of biogas at wastewater treatment facilities to offset the energy demands associated with wastewater treatment. Recuperative thickening (RT) is a promising technique which involves recycling a portion of the digested solids back to the incoming feed. In general there exists a significant number of knowledge gaps in the field of RT because the studies that have been conducted to date have almost exclusively occurred in pilot plant or full scale trials; this approach greatly limits the amount of process optimization that can be done in a given trial. In this work, a detailed and comprehensive study of RT was conducted at the lab scale; two custom designed digesters (capacity = 1.5 L) were operated in parallel with one acting as a 'control' digester and the other operating under a semi-batch RT mode. There was no significant change in biogas methane composition for the two digesters, however the RT digester had an average biogas productivity over two times higher than the control one. It was found that the recycling of the polymer flocculant back into the RT digester resulted in a significant improvement in dewatering performance. At the highest polymer concentration tested, the capillary suction time (CST) values for flocculated samples for the RT digester were over 6 times lower than the corresponding values for the control digester. Thus, there exists an opportunity to decrease the overall consumption of polymer flocculants through judicious selection of the dose of polymer flocculant that is used both for the thickening and end-stage dewatering steps in RT processes. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Development of a process control sensor for the glass industry. Phase 2: Prototype design, development and demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, M.; Candee, A.; Koppang, R.

    1994-06-01

    This report describes an advanced multichannel, on-line optical system for the non-contact measurement of forehearth glass melt temperatures at depth. The analyzer employs multiple narrow infrared (IR) band measurements of glass radiation to reconstruct the glass temperature profiles at depth. The TAS replaces expensive Tri-plex thermocouples, which frequently have service lives as short as 6 months to 1 years. By using passive non-contact sensor heads and fiber optic cables, temperature sensitive electronic components can be located at a safe distance from the hostile process environment. This provides significantly better reliability of the vulnerable electro-optic components and ready access for maintenance.

  10. Functional uniform priors for nonlinear modeling.

    Science.gov (United States)

    Bornkamp, Björn

    2012-09-01

    This article considers the topic of finding prior distributions when a major component of the statistical model depends on a nonlinear function. Using results on how to construct uniform distributions in general metric spaces, we propose a prior distribution that is uniform in the space of functional shapes of the underlying nonlinear function and then back-transform to obtain a prior distribution for the original model parameters. The primary application considered in this article is nonlinear regression, but the idea might be of interest beyond this case. For nonlinear regression the so constructed priors have the advantage that they are parametrization invariant and do not violate the likelihood principle, as opposed to uniform distributions on the parameters or the Jeffrey's prior, respectively. The utility of the proposed priors is demonstrated in the context of design and analysis of nonlinear regression modeling in clinical dose-finding trials, through a real data example and simulation.

  11. Conformational analysis of processivity clamps in solution demonstrates that tertiary structure does not correlate with protein dynamics.

    Science.gov (United States)

    Fang, Jing; Nevin, Philip; Kairys, Visvaldas; Venclovas, Ceslovas; Engen, John R; Beuning, Penny J

    2014-04-08

    The relationship between protein sequence, structure, and dynamics has been elusive. Here, we report a comprehensive analysis using an in-solution experimental approach to study how the conservation of tertiary structure correlates with protein dynamics. Hydrogen exchange measurements of eight processivity clamp proteins from different species revealed that, despite highly similar three-dimensional structures, clamp proteins display a wide range of dynamic behavior. Differences were apparent both for structurally similar domains within proteins and for corresponding domains of different proteins. Several of the clamps contained regions that underwent local unfolding with different half-lives. We also observed a conserved pattern of alternating dynamics of the α helices lining the inner pore of the clamps as well as a correlation between dynamics and the number of salt bridges in these α helices. Our observations reveal that tertiary structure and dynamics are not directly correlated and that primary structure plays an important role in dynamics.

  12. Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways.

    Science.gov (United States)

    Mulat, Daniel Girma; Jacobi, H Fabian; Feilberg, Anders; Adamsen, Anders Peter S; Richnow, Hans-Hermann; Nikolausz, Marcell

    2015-10-23

    Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes.

  13. Changing Feeding Regimes To Demonstrate Flexible Biogas Production: Effects on Process Performance, Microbial Community Structure, and Methanogenesis Pathways

    Science.gov (United States)

    Mulat, Daniel Girma; Jacobi, H. Fabian; Feilberg, Anders; Adamsen, Anders Peter S.; Richnow, Hans-Hermann

    2015-01-01

    Flexible biogas production that adapts biogas output to energy demand can be regulated by changing feeding regimes. In this study, the effect of changes in feeding intervals on process performance, microbial community structure, and the methanogenesis pathway was investigated. Three different feeding regimes (once daily, every second day, and every 2 h) at the same organic loading rate were studied in continuously stirred tank reactors treating distiller's dried grains with solubles. A larger amount of biogas was produced after feeding in the reactors fed less frequently (once per day and every second day), whereas the amount remained constant in the reactor fed more frequently (every 2 h), indicating the suitability of the former for the flexible production of biogas. Compared to the conventional more frequent feeding regimes, a methane yield that was up to 14% higher and an improved stability of the process against organic overloading were achieved by employing less frequent feeding regimes. The community structures of bacteria and methanogenic archaea were monitored by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA and mcrA genes, respectively. The results showed that the composition of the bacterial community varied under the different feeding regimes, and the observed T-RFLP patterns were best explained by the differences in the total ammonia nitrogen concentrations, H2 levels, and pH values. However, the methanogenic community remained stable under all feeding regimes, with the dominance of the Methanosarcina genus followed by that of the Methanobacterium genus. Stable isotope analysis showed that the average amount of methane produced during each feeding event by acetoclastic and hydrogenotrophic methanogenesis was not influenced by the three different feeding regimes. PMID:26497462

  14. Magnetostatics of the uniformly polarized torus

    DEFF Research Database (Denmark)

    Beleggia, Marco; De Graef, Marc; Millev, Yonko

    2009-01-01

    We provide an exhaustive description of the magnetostatics of the uniformly polarized torus and its derivative self-intersecting (spindle) shapes. In the process, two complementary approaches have been implemented, position-space analysis of the Laplace equation with inhomogeneous boundary...

  15. On Uniform Weak König's Lemma

    DEFF Research Database (Denmark)

    Kohlenbach, Ulrich

    2002-01-01

    is of interest in the context of explicit mathematics as developed by S. Feferman. The elimination process in Kohlenbach [10] actually can be used to eliminate even this uniform weak Konig's lemma provided that PRA only has a quantifier-free rule of extensionality QF-ER instead of the full axioms (E...

  16. Graphene Conductance Uniformity Mapping

    DEFF Research Database (Denmark)

    Buron, Jonas Christian Due; Petersen, Dirch Hjorth; Bøggild, Peter

    2012-01-01

    We demonstrate a combination of micro four-point probe (M4PP) and non-contact terahertz time-domain spectroscopy (THz-TDS) measurements for centimeter scale quantitative mapping of the sheet conductance of large area chemical vapor deposited graphene films. Dual configuration M4PP measurements......, demonstrated on graphene for the first time, provide valuable statistical insight into the influence of microscale defects on the conductance, while THz-TDS has potential as a fast, non-contact metrology method for mapping of the spatially averaged nanoscopic conductance on wafer-scale graphene with scan times......, dominating the microscale conductance of the investigated graphene film....

  17. Brain tissue oxygen amperometry in behaving rats demonstrates functional dissociation of dorsal and ventral hippocampus during spatial processing and anxiety

    Science.gov (United States)

    McHugh, Stephen B; Fillenz, Marianne; Lowry, John P; Rawlins, J Nicolas P; Bannerman, David M

    2011-01-01

    Traditionally, the function of the hippocampus (HPC) has been viewed in unitary terms, but there is growing evidence that the HPC is functionally differentiated along its septotemporal axis. Lesion studies in rodents and functional brain imaging in humans suggest a preferential role for the septal HPC in spatial learning and a preferential role for the temporal HPC in anxiety. To better enable cross-species comparison, we present an in vivo amperometric technique that measures changes in brain tissue oxygen at high temporal resolution in freely-moving rats. We recorded simultaneously from the dorsal (septal; dHPC) and ventral (temporal; vHPC) HPC during two anxiety tasks and two spatial tasks on the radial maze. We found a double-dissociation of function in the HPC, with increased vHPC signals during anxiety and increased dHPC signals during spatial processing. In addition, dHPC signals were modulated by spatial memory demands. These results add a new dimension to the growing consensus for a differentiation of HPC function, and highlight tissue oxygen amperometry as a valuable tool to aid translation between animal and human research. PMID:21105915

  18. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 2, July 1--September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    The project involves the construction of a 260 tons-per-day (TPD) or 80,000 gallon per day methanol demonstration unit utilizing an existing coal-derived synthesis gas from Eastman. The new equipment consists of synthesis gas feed preparation and compression, liquid phase reactor and auxiliaries, product distillation, and utilities. The technology to be demonstrated was developed by Air Products in a DOE sponsored program that started in 1981. Originally tested at a small, DOE-owned experimental facility in LaPorte, Texas, the LPMEOH{trademark} process offers several advantages over current methods of making methanol. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The liquid dissipates heat from the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the gas-to-methanol reaction to proceed at higher rates. The process is ideally suited to the type of gas produced by modern coal gasifiers. At the Eastman Chemical complex, the technology will be integrated with existing coal gasifiers to demonstrate the commercially important aspects of the operation of the LPMEOH{trademark} Process to produce methanol. A four-year demonstration will prove the commercial applicability of the process. An off-site product-use test program will prove the suitability of the methanol as a transportation fuel and as a fuel for stationary applications in the power industry.

  19. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1983-01-01

    Free radical chlorination of methane is used in organic chemistry to introduce free radical/chain reactions. In spite of its common occurrence, demonstrations of the reaction are uncommon. Therefore, such a demonstration is provided, including background information, preparation of reactants/reaction vessel, introduction of reactants, irradiation,…

  20. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1983-01-01

    Discusses a supplement to the "water to rose" demonstration in which a pink color is produced. Also discusses blood buffer demonstrations, including hydrolysis of sodium bicarbonate, simulated blood buffer, metabolic acidosis, natural compensation of metabolic acidosis, metabolic alkalosis, acidosis treatment, and alkalosis treatment. Procedures…

  1. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1987-01-01

    Describes two laboratory demonstrations in chemistry. One uses dry ice, freon, and freezer bags to demonstrate volume changes, vapor-liquid equilibrium, a simulation of a rain forest, and vaporization. The other uses the clock reaction technique to illustrate fast reactions and kinetic problems in releasing carbon dioxide during respiration. (TW)

  2. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1986-01-01

    Outlines a simple, inexpensive way of demonstrating electroplating using the reaction between nickel ions and copper metal. Explains how to conduct a demonstration of the electrolysis of water by using a colored Na2SO4 solution as the electrolyte so that students can observe the pH changes. (TW)

  3. Signal Detection for Uniform Renewal Processes.

    Science.gov (United States)

    1982-06-01

    a surface) are N N 2 A N N 2-N X ajqj ,f= aj; T N ! b~.Ij bN I a J q1 j bjqj 1 b Jul Jul jul ’ jl For N > 2, after some algebraic simplification the... Durbin , J. (1961). Sow methods of constructing exact tests, Biometrika, 48, 41-55. S. Durbin , J. (1973). Distribution Iheo for Tests &smd a the Sample

  4. 基于m-相依序列的学习机器相对一致收敛的界%Bounds on the Rate of Relative Uniform Convergence for Learning Machine with m-dependent Processes

    Institute of Scientific and Technical Information of China (English)

    王华丽

    2011-01-01

    The generalization performance is the main purpose of machine learning theoretical research.To study the generalization ability with the dependent observations in this paper,we extend the results to the case where the i.i.d.sequence replaced by m-dependent processes.We derive the bounds on the rate of relative uniform convergence of the empirical risks to their expected risks,and improve current results with m-dependent processes.We also establish the bound that describes the generalization ability of ERM(Empirical risk minimization)algorithm with m-dependent processes.%为了研究m-相依序列下学习机器的推广性能,把基于独立同分布的结果推广到m-相依序列,建立采用ERM算法的学习机器的经验风险到它的期望风险相对一致收敛速率的界.并对m-相依序列现有的结论进行改进,得到了m-相依序列下,采用经验风险最小化算法学习机器的推广性能的界.

  5. Processing of Bimodal Grain-Sized Ultrafine-Grained Dual Phase Microalloyed V-Nb Steel with 1370 MPa Strength and 16 pct Uniform Elongation Through Warm Rolling and Intercritical Annealing

    Science.gov (United States)

    Papa Rao, M.; Subramanya Sarma, V.; Sankaran, S.

    2014-11-01

    Ultrafine-grained dual phase microalloyed V-Nb steel with ultimate tensile strength of 1371 MPa and uniform elongation of 16 pct characterized by bimodal ferrite grain structure was obtained through warm rolling and subsequent intercritical annealing. The bimodal ferrite grain structure with uniform dispersion of Nb/V carbides and strong γ-fiber texture promoted high strain hardening rate and high uniform elongation and high strength is attributed to ultrafine-grained ferrite and martensite.

  6. UMAPRM: Uniformly sampling the medial axis

    KAUST Repository

    Yeh, Hsin-Yi Cindy

    2014-05-01

    © 2014 IEEE. Maintaining clearance, or distance from obstacles, is a vital component of successful motion planning algorithms. Maintaining high clearance often creates safer paths for robots. Contemporary sampling-based planning algorithms That utilize The medial axis, or The set of all points equidistant To Two or more obstacles, produce higher clearance paths. However, They are biased heavily Toward certain portions of The medial axis, sometimes ignoring parts critical To planning, e.g., specific Types of narrow passages. We introduce Uniform Medial Axis Probabilistic RoadMap (UMAPRM), a novel planning variant That generates samples uniformly on The medial axis of The free portion of Cspace. We Theoretically analyze The distribution generated by UMAPRM and show its uniformity. Our results show That UMAPRM\\'s distribution of samples along The medial axis is not only uniform but also preferable To other medial axis samplers in certain planning problems. We demonstrate That UMAPRM has negligible computational overhead over other sampling Techniques and can solve problems The others could not, e.g., a bug Trap. Finally, we demonstrate UMAPRM successfully generates higher clearance paths in The examples.

  7. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report No. 1, October 1, 1993--June 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    The Liquid Phase Methanol (LPMEOH{trademark}) Demonstration Project at Kingsport, Tennessee is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products and Chemicals, Inc. (Air Products). This document describes major accomplishments in project development for Fiscal Year 1993. The preliminary process hazards review, project safety plan, schedule, and cost management report are included as appendices. The demonstration is sited at the Eastman Chemical Company (Eastman) complex in Kingsport. Air Products and Eastman are working on a partnership agreement which will form the Air Products Liquid Phase Conversion Company, L.P. As a limited partner in the venture, Eastman will own and operate the demonstration unit. The project involves the construction of a 260 tons-per-day (TPD) or 80,000 gallon per day methanol demonstration unit utilizing an existing coal-derived synthesis gas from Eastman. The new equipment consists of synthesis gas feed preparation and compression, liquid phase reactor and auxiliaries, product distillation, and utilities. The technology to be demonstrated was developed by Air Products in a DOE sponsored program that started in 1981. Originally tested at a small, DOE-owned experimental facility in LaPorte, Texas, the LPMEOH{trademark} process offers several advantages over current methods of making methanol. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The liquid dissipates heat from the chemical reaction away from the catalyst surface, protecting the catalyst, and allowing the gas-to-methanol reaction to proceed at higher rates. The process is ideally suited to the type of gas produced by modem coal gasifiers. At the Eastman Chemical complex, the technology will be integrated with existing coal gasifiers to demonstrate the commercially important aspects of the operation of the LPMEOH{trademark} Process to produce methanol.

  8. A uniform parameterization of moment tensors

    Science.gov (United States)

    Tape, C.; Tape, W.

    2015-12-01

    A moment tensor is a 3 x 3 symmetric matrix that expresses an earthquake source. We construct a parameterization of the five-dimensional space of all moment tensors of unit norm. The coordinates associated with the parameterization are closely related to moment tensor orientations and source types. The parameterization is uniform, in the sense that equal volumes in the coordinate domain of the parameterization correspond to equal volumes of moment tensors. Uniformly distributed points in the coordinate domain therefore give uniformly distributed moment tensors. A cartesian grid in the coordinate domain can be used to search efficiently over moment tensors. We find that uniformly distributed moment tensors have uniformly distributed orientations (eigenframes), but that their source types (eigenvalue triples) are distributed so as to favor double couples. An appropriate choice of a priori moment tensor probability is a prerequisite for parameter estimation. As a seemingly sensible choice, we consider the homogeneous probability, in which equal volumes of moment tensors are equally likely. We believe that it will lead to improved characterization of source processes.

  9. Naturalness preserved enhancement algorithm for non-uniform illumination images.

    Science.gov (United States)

    Wang, Shuhang; Zheng, Jin; Hu, Hai-Miao; Li, Bo

    2013-09-01

    Image enhancement plays an important role in image processing and analysis. Among various enhancement algorithms, Retinex-based algorithms can efficiently enhance details and have been widely adopted. Since Retinex-based algorithms regard illumination removal as a default preference and fail to limit the range of reflectance, the naturalness of non-uniform illumination images cannot be effectively preserved. However, naturalness is essential for image enhancement to achieve pleasing perceptual quality. In order to preserve naturalness while enhancing details, we propose an enhancement algorithm for non-uniform illumination images. In general, this paper makes the following three major contributions. First, a lightness-order-error measure is proposed to access naturalness preservation objectively. Second, a bright-pass filter is proposed to decompose an image into reflectance and illumination, which, respectively, determine the details and the naturalness of the image. Third, we propose a bi-log transformation, which is utilized to map the illumination to make a balance between details and naturalness. Experimental results demonstrate that the proposed algorithm can not only enhance the details but also preserve the naturalness for non-uniform illumination images.

  10. School Uniforms: Esprit de Corps.

    Science.gov (United States)

    Ryan, Rosemary P.; Ryan, Thomas E.

    1998-01-01

    The benefits of school uniforms far outweigh their short-term costs. School uniforms not only keep students safe, but they increase their self-esteem, promote a more positive attitude toward school, lead to improved student behavior, and help blur social-class distinctions. Students are allowed to wear their own political or religious messages,…

  11. How do video-based demonstration assessment tasks affect problem-solving process, test anxiety, chemistry anxiety and achievement in general chemistry students?

    Science.gov (United States)

    Terrell, Rosalind Stephanie

    2001-12-01

    Because paper-and-pencil testing provides limited knowledge about what students know about chemical phenomena, we have developed video-based demonstrations to broaden measurement of student learning. For example, students might be shown a video demonstrating equilibrium shifts. Two methods for viewing equilibrium shifts are changing the concentration of the reactants and changing the temperature of the system. The students are required to combine the data collected from the video and their knowledge of chemistry to determine which way the equilibrium shifts. Video-based demonstrations are important techniques for measuring student learning because they require students to apply conceptual knowledge learned in class to a specific chemical problem. This study explores how video-based demonstration assessment tasks affect problem-solving processes, test anxiety, chemistry anxiety and achievement in general chemistry students. Several instruments were used to determine students' knowledge about chemistry, students' test and chemistry anxiety before and after treatment. Think-aloud interviews were conducted to determine students' problem-solving processes after treatment. The treatment group was compared to a control group and a group watching video demonstrations. After treatment students' anxiety increased and achievement decreased. There were also no significant differences found in students' problem-solving processes following treatment. These negative findings may be attributed to several factors that will be explored in this study.

  12. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L.

    1990-01-01

    Included are three demonstrations that include the phase change of ice when under pressure, viscoelasticity and colloid systems, and flame tests for metal ions. The materials, procedures, probable results, and applications to real life situations are included. (KR)

  13. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1980-01-01

    Presented is a Corridor Demonstration which can be set up in readily accessible areas such as hallways or lobbies. Equipment is listed for a display of three cells (solar cells, fuel cells, and storage cells) which develop electrical energy. (CS)

  14. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1987-01-01

    Presents three demonstrations suitable for undergraduate chemistry classes. Focuses on experiments with calcium carbide, the induction by iron of the oxidation of iodide by dichromate, and the classical iodine clock reaction. (ML)

  15. Develop and Demonstrate the Cellulose to Ethanol Process: Executive Summary of the Final Technical Report, 17 September 1980 - 17 March 1982

    Energy Technology Data Exchange (ETDEWEB)

    Emert, George H.; Becker, Dana K.; Bevernitz, Kurt J.; Gracheck, Stephen J.; Kienholz, Eldon W.; Rivers, Dougals B.; Zoldak, Bernadette R.; Woodford, Lindley C.

    1982-01-01

    The Biomass Research Center at the University of Arkansas was contracted by the Solar Energy Research Institute to 'Develop and Demonstrate the Cellulose to Ethanol Process.' The purpose of the contract was to accelerate site selection, site specific engineering, and research and development leading to the determination of the feasibility of economically operating a cellulose to ethanol commercial scale plant.

  16. ARSENIC REMOVAL FROM DRINKING WATER BY PROCESS MODIFICATION TO COAGULATION/FILTRATION. USEPA DEMONSTRATION PROJECT AT LIDGERWOOD, ND. FINAL PERFORMANCE EVALUATION REPORT

    Science.gov (United States)

    This report documents the activities performed and the results obtained for the arsenic removal treatment technology demonstration project at the Lidgerwood, North Dakota site. The objectives of the project were to evaluate: (1) the effectiveness of process modifications to an e...

  17. Statistical Test for Bivariate Uniformity

    Directory of Open Access Journals (Sweden)

    Zhenmin Chen

    2014-01-01

    Full Text Available The purpose of the multidimension uniformity test is to check whether the underlying probability distribution of a multidimensional population differs from the multidimensional uniform distribution. The multidimensional uniformity test has applications in various fields such as biology, astronomy, and computer science. Such a test, however, has received less attention in the literature compared with the univariate case. A new test statistic for checking multidimensional uniformity is proposed in this paper. Some important properties of the proposed test statistic are discussed. As a special case, the bivariate statistic test is discussed in detail in this paper. The Monte Carlo simulation is used to compare the power of the newly proposed test with the distance-to-boundary test, which is a recently published statistical test for multidimensional uniformity. It has been shown that the test proposed in this paper is more powerful than the distance-to-boundary test in some cases.

  18. Uniformity microsprinkler irrigation system using statistical quality control

    OpenAIRE

    Maurício Guy de Andrade; Marcio Antonio Vilas Boas; Jair Antonio Cruz Siqueira; Mireille Sato; Jonathan Dieter; Eliane Hermes; Erivelto Mercante

    2017-01-01

    ABSTRACT: The objective of this study was to evaluate the use of statistical quality control tools in the analysis of the uniformity of a microsprinkler irrigation system. For the analysis of irrigation Christiansen uniformity coefficient (CUC) and the distribution uniformity coefficient (DU) were statistically analyzed by means of the Shewhart control charts and process capability index (Cp). For the experiment 25 tests were carried out with a single micro sprinkler and subsequently seven di...

  19. Fine uniform filament superconductors

    Science.gov (United States)

    Riley, Jr., Gilbert N.; Li, Qi; Roberts, Peter R.; Antaya, Peter D.; Seuntjens, Jeffrey M.; Hancock, Steven; DeMoranville, Kenneth L.; Christopherson, Craig J.; Garrant, Jennifer H.; Craven, Christopher A.

    2002-01-01

    A multifilamentary superconductor composite having a high fill factor is formed from a plurality of stacked monofilament precursor elements, each of which includes a low density superconductor precursor monofilament. The precursor elements all have substantially the same dimensions and characteristics, and are stacked in a rectilinear configuration and consolidated to provide a multifilamentary precursor composite. The composite is thereafter thermomechanically processed to provide a superconductor composite in which each monofilament is less than about 50 microns thick.

  20. Índice de capacidade do processo na avaliação da irrigação por aspersão Process capacity index in the uniformity evaluation of sprinkler irrigation

    Directory of Open Access Journals (Sweden)

    André L Justi

    2010-04-01

    Full Text Available Analisar a qualidade da irrigação, além de avaliar seu bom funcionamento, é uma forma de verificar a viabilidade de sua implantação e operação. Como a uniformidade de distribuição é um dos parâmetros mais utilizados para essa avaliação, este trabalho objetivou utilizar técnicas de engenharia de qualidade, usando o índice de capacidade do processo (Cpl para avaliar a uniformidade de distribuição de água em um sistema de irrigação por aspersão convencional. Os ensaios foram conduzidos no Núcleo Experimental de Engenharia Agrícola, UNIOESTE, com dois aspersores modelo Super10, marca NAANDAN, espaçados 9 m entre si, durante 25 irrigações de 1 h cada. Os dados climáticos foram coletados a cada 10 min, por uma estação meteorológica sem fio. Encontraram-se um CUC médio de 79,72% e velocidade do vento média de 1,85 m s-1. Foram aplicados os testes de controle de qualidade, elaborando os gráficos de controle de Shewhart e calculado o índice de capacidade do processo (Cpl, sendo que os resultados obtidos permitem afirmar que a utilização do índice de capacidade do processo torna-se uma ferramenta poderosa para classificar sistemas de irrigação em função de sua uniformidade de distribuição.Analyzing the irrigation quality, besides evaluating its good operation, is a form of verifying the viability of its implantation and operation. As the distribution uniformity is one of the most used parameters for that evaluation, this work aimed to use techniques of quality engineering, by using the process capacity index (Cpl to evaluate the uniformity of water distribution in overhead irrigation by sprinkler. The research was carried out at the Experimental Center of Agricultural Engineering, UNIOESTE, with 2 sprinklers Super10 model, NAANDAN, spaced 9m between themselves, during 25 irrigations with 1 h each. The Weather data were collected every 10 min. by a wireless weather station. It was found a medium CUC of 79.72% and

  1. Experiments Demonstrate Geothermal Heating Process

    Science.gov (United States)

    Roman, Harry T.

    2012-01-01

    When engineers design heat-pump-based geothermal heating systems for homes and other buildings, they can use coil loops buried around the perimeter of the structure to gather low-grade heat from the earth. As an alternative approach, they can drill well casings and store the summer's heat deep in the earth, then bring it back in the winter to warm…

  2. Tested Demonstrations.

    Science.gov (United States)

    Gilbert, George L., Ed.

    1987-01-01

    Describes two demonstrations to illustrate characteristics of substances. Outlines a method to detect the changes in pH levels during the electrolysis of water. Uses water pistols, one filled with methane gas and the other filled with water, to illustrate the differences in these two substances. (TW)

  3. ICT Demonstration

    DEFF Research Database (Denmark)

    Jensen, Tine Wirenfeldt; Bay, Gina

    In this demonstration we present and discuss two interrelated on-line learning resources aimed at supporting international students at Danish universities in building study skills (the Study Metro) and avoiding plagiarism (Stopplagiarism). We emphasize the necessity of designing online learning r...

  4. Uniform Acceleration in General Relativity

    CERN Document Server

    Friedman, Yaakov

    2016-01-01

    We extend de la Fuente and Romero's defining equation for uniform acceleration in a general curved spacetime from linear acceleration to the full Lorentz covariant uniform acceleration. In a flat spacetime background, we have explicit solutions. We use generalized Fermi-Walker transport to parallel transport the Frenet basis along the trajectory. In flat spacetime, we obtain velocity and acceleration transformations from a uniformly accelerated system to an inertial system. We obtain the time dilation between accelerated clocks. We apply our acceleration transformations to the motion of a charged particle in a constant electromagnetic field and recover the Lorentz-Abraham-Dirac equation.

  5. Design of Production Test IP-262-A-11-FP -- Evaluation of projection fuel elements for use in ribbed process tubes -- Demonstration loading

    Energy Technology Data Exchange (ETDEWEB)

    Hodgson, W.H.; Hall, R.E.

    1959-06-29

    For several years, a major category of fuel element failures has been the side corrosion type, characterized by localized accelerated fuel element jacket corrosion. Since it has been demonstrated {sup 1} that misalignment of fuel elements in a process tube will produce flow patterns and accelerated corrosion, termed ``hot spots``, failure to align the fuel elements in process tubes is considered a contributing factor in the production of side corrosion failures. Preliminary testing of both self-supporting and ``bumper`` fuel elements is underway. Data on the self-supporting fuel elements have demonstrated that the bridge-rail projections have sufficient support strength, do not of themselves create a corrosion problem and in actuality probably eliminate any hot-spot areas. Although one tube of bumper fuel elements in KW Reactor {sup 3} has been discharged, data are not as yet available. Potentially, the most sever corrosion conditions exist during the summer months when reactor inlet temperatures are high. It is desirable then, provided bumper fuel elements limit hot- spot corrosion, to evaluate the bumper concept for large scale use possibly by the summer of 1960. To accomplish this, a demonstration loading of the bumper type fuel elements must be underway by about July, 1959. The purpose of this report is to present the design of a test to evaluate the fabrication process and irradiation performance of fuel elements having projections, which may prevent misalignment in ribbed process tubes and meet the aforementioned goals.

  6. 基于均匀设计的定量指纹图谱优选丹黄凝胶醇提工艺%Optimization of Ethanol Extraction Process for Quantified Fingerprint of Danhuang Gel Based on Uniform Design

    Institute of Scientific and Technical Information of China (English)

    陈新民; 李俊松; 李文; 刘训红; 蔡宝昌

    2011-01-01

    Objective: To optimize the ethanol extraction process and the condition of Danhuang gel for quantified fingerprint technique by uniform design. Method: An U8 (82 × 42) uniform design was used to prepare the samples according to the results and the effects of ethanol concentration, ethanol amount, times of extraction and the number of extraction on the yield of extract by HPLC fingerprint technology. Multi-nonlinear mathematic models were used to estimate the relationship between response index and factor variables with multi-index of the content of chrysophanol and berberine, the total area of characteristic peaks of HPLC and the yield of powdered extract. The response surface and contour plots were delineated according to best-fit mathematic model, and the optimum range of technological parameters and optimum ethanol extraction condition were selected by the response surface and contour plots. Result: Two order quadratic equation described the relationship between response indexes and factor variables with a regression coefficient of 0.983 3. The optimum condition of the ethanol extraction was obtained that the raw material amount was extracted with 7 volumes of 65% ethanol three times for 2 h per extraction process.Conclusion: The extraction method optimized by quantified fingerprint technique combined with uniform design and response surface analysis is stable and feasible. The study could provide the references and groundwork for its further investigation.%目的:运用均匀设计并结合定量指纹图技术优化丹黄凝胶醇提工艺参数.方法:采用HPLC指纹图谱技术,按U8(82×42)均匀设计考察乙醇体积分数、乙醇用量、提取次数和提取时间4个因素,以大黄酚和小檗碱含量、HPLC指纹图谱特征峰总面积之和以及干浸膏得率为综合评价指标,采用多元非线性拟合,建立效应指标和考察因素之间的数学模型,根据最佳数学模型描绘效应面图和等高线图,确定醇提工艺

  7. Sckool Dress Rule, Uniform Policies

    Institute of Scientific and Technical Information of China (English)

    潘志强

    2005-01-01

    Our schools believe that a uniform policy will provide a better environment, promote positive selfesteem, encourage an atmosphere for greater discipline, and increase learning opportunities for students by removing many of the distractions associated with various types of clothing.

  8. Uniform polyhedra: old and new

    CERN Document Server

    Melikhov, Sergey A

    2011-01-01

    We develop a theory of metric polyhedra, including locally infinite dimensional ones. Motivated by algebraic topology, we focus on their uniform properties (i.e., those preserved by homeomorphisms that are uniformly continuous in both directions) but in doing so we also study their metric and Lipschitz properties. On the combinatorial side, (the face posets of) simplicial or cubical complexes do not suffice for this, and we have to rework some basic PL topology into a purely combinatorial machinery (with all homeomorphisms eliminated in favor of combinatorial isomorphisms) based on posets and their canonical subdivision (which is just the poset of all order intervals of the given poset, ordered by inclusion). Antecedents of this approach to PL topology are found in van Kampen's 1929 dissertation and in modern Topological Combinatorics. Our main results establish, in particular, close but troubled relations between uniform polyhedra and uniform ANRs, and appear to provide a satisfactory solution to an open-end...

  9. Landing the uniformly accelerating observers

    OpenAIRE

    Rothenstein, Bernhard; Popescu, Stefan; Gruber, Ronald P.

    2006-01-01

    Observers of the uniformly accelerating observers or the observers who make up the system of uniformly accelerating observers reach the same velocity V at different times ti which depends on V and on theirs acceleration gi. Considering a platform that moves with constant velocity V, the observers can land smoothly on it. Their ages and locations in the inertial reference frame attached to the platform are reckoned and compared.

  10. Evaluation of Processing Technology for Jianchangbang Cyperus rotundus Based on Uniform Design Method%基于均匀设计法的建昌帮四制香附炮制工艺评价

    Institute of Scientific and Technical Information of China (English)

    胡志方; 胡律江; 郭慧玲; 金鑫; 赵晓娟; 闫柏屹

    2012-01-01

    Objective: To investigate effect of the amount of accessories, processing time and temperature on main active components from Jiangxi Jianchangbang Cyperus rotundus. Method: With a-cyperone and total flavonoids as indexes, the content of a-cyperone was determined by HPLC, processing technology of Jiangxi Jianchangbang C. rotundus was optimized by uniform design test. Result: The smaller the dosage of salt and vinegar, the lower processing temperature and the shorter frying time, the higher the content of a-cyperone; The dosage of ginger and rice wine had no significant influence on the content of a-cyperone. The greater the dosage of salt and vinegar, the higher frying temperature, the higher the content of total flavonoids; Ginger, wine and processing time had no significant impact on the content of total flavonoids. Conclusion:The dosage of salt and vinegar, processing temperature and time had a certain influence on the content of a-cyperone and total flavonoids from Jianchangbang C. rotundus, both of them showed negative correlation, it suggested that evaluation of processing technology should be comprehensive consideration by combining with of pharmacodynamic index.%目的:探讨辅料用量、炮制温度及时间对江西建昌帮四制香附主要活性成分的影响.方法:以α-香附酮及总黄酮为考察指标,HPLC测定α-香附酮含量,采用均匀设计法优选江西建昌帮四制香附炮制工艺.结果:盐、醋的用量越小、温度越低、炒制时间越短,α-香附酮含量越高;生姜和黄酒的用量对α-香附酮含量无显著性影响.盐、醋的用量越大、炒制的温度越高,则总黄酮含量越高;生姜、酒及炮制时间对总黄酮含量无显著性影响.结论:建昌帮四制香附炮制辅料盐和醋的用量、炮制温度及时间对主要活性成分α-香附酮及总黄酮的含量有一定影响,且两者呈负相关,提示对炮制工艺的评价应结合药效指标综合考虑.

  11. Micro-cantilevers for non-destructive characterization of nanograss uniformity

    DEFF Research Database (Denmark)

    Petersen, Dirch Hjorth; Wang, Fei; Olesen, Mikkel Buster

    2011-01-01

    measurements may be useful for process uniformity characterization. The method is applied for characterization of TiW coated nanograss uniformity. Three-way flexible L-shaped cantilever electrodes are used to avoid damage to the fragile surface, and a relative standard deviation on measurement repeatability......We demonstrate an application of three-way flexible micro four-point probes for indirect uniformity characterization of surface morphology. The mean sheet conductance of a quasi-planar 3D nanostructured surface is highly dependent on the surface morphology, and thus accurate sheet conductance...... of 0.12 % is obtained with a measurement yield of 97%. Finally, variations in measured sheet conductance are correlated to the surface morphology as characterized by electron microscopy....

  12. Temperature Uniformity of Wafer on a Large-Sized Susceptor for a Nitride Vertical MOCVD Reactor

    Institute of Scientific and Technical Information of China (English)

    LI Zhi-Ming; JIANG Hai-Ying; HAN Yan-Bin; LI Jin-Ping; YIN Jian-Qin; ZHANG Jin-Cheng

    2012-01-01

    The effect of coil location on wafer temperature is analyzed in a vertical MOCVD reactor by induction heating.It is observed that the temperature distribution in the wafer with the coils under the graphite susceptor is more uniform than that with the coils around the outside wall of the reactor.For the case of coils under the susceptor,we find that the thickness of the susceptor,the distance from the coils to the susceptor bottom and the coil turns significantly affect the temperature uniformity of the wafer. An optimization process is executed for a 3-inch susceptor with this kind of structure,resulting in a large improvement in the temperature uniformity.A further optimization demonstrates that the new susceptor structure is also suitable for either multiple wafers or large-sized wafers approaching 6 and 8 inches.

  13. Downsampling Non-Uniformly Sampled Data

    Directory of Open Access Journals (Sweden)

    Fredrik Gustafsson

    2007-10-01

    Full Text Available Decimating a uniformly sampled signal a factor D involves low-pass antialias filtering with normalized cutoff frequency 1/D followed by picking out every Dth sample. Alternatively, decimation can be done in the frequency domain using the fast Fourier transform (FFT algorithm, after zero-padding the signal and truncating the FFT. We outline three approaches to decimate non-uniformly sampled signals, which are all based on interpolation. The interpolation is done in different domains, and the inter-sample behavior does not need to be known. The first one interpolates the signal to a uniformly sampling, after which standard decimation can be applied. The second one interpolates a continuous-time convolution integral, that implements the antialias filter, after which every Dth sample can be picked out. The third frequency domain approach computes an approximate Fourier transform, after which truncation and IFFT give the desired result. Simulations indicate that the second approach is particularly useful. A thorough analysis is therefore performed for this case, using the assumption that the non-uniformly distributed sampling instants are generated by a stochastic process.

  14. A conceptual demonstration of freeze desalination-membrane distillation (FD-MD) hybrid desalination process utilizing liquefied natural gas (LNG) cold energy.

    Science.gov (United States)

    Wang, Peng; Chung, Tai-Shung

    2012-09-01

    The severe global water scarcity and record-high fossil oil price have greatly stimulated the research interests on new desalination technologies which can be driven by renewable energy or waste energy. In this study, a hybrid desalination process comprising freeze desalination and membrane distillation (FD-MD) processes was developed and explored in an attempt to utilize the waste cold energy released from re-gasification of liquefied natural gas (LNG). The concept of this technology was demonstrated using indirect-contact freeze desalination (ICFD) and direct-contact membrane distillation (DCMD) configurations. By optimizing the ICFD operation parameters, namely, the usage of nucleate seeds, operation duration and feed concentration, high quality drinkable water with a low salinity ∼0.144 g/L was produced in the ICFD process. At the same time, using the optimized hollow fiber module length and packing density in the DCMD process, ultra pure water with a low salinity of 0.062 g/L was attained at a condition of high energy efficiency (EE). Overall, by combining FD and MD processes and adopting the optimized operation parameters, the hybrid FD-MD system has been successfully demonstrated. A high total water recovery of 71.5% was achieved, and the water quality obtained met the standard for drinkable water. In addition, with results from specific energy calculation, it was proven that the hybrid process is an energy-saving process and utilization of LNG cold energy could greatly reduce the total energy consumption. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. ICT Demonstration

    DEFF Research Database (Denmark)

    Jensen, Tine Wirenfeldt; Bay, Gina

    the consequences students can expect if they do plagiarize. The second section presents the basic tools for ensuring academic integrity by introducing the basic concepts necessary to avoid plagiarism: quotations, in-text citations and summarizing. A quiz allows students to test their knowledge about plagiarism......., and the designer of the Study Metro shares an educational developer’s perspective on the concept of plagiarism in a podcast in ‘Stop Plagiarism’. Both learning resources reflect a holistic understanding of the academic learning process which views finding information, handling sources, choosing a topic......, formulating a research problem as well as writing techniques as deeply integrated elements of the academic work process. The importance of creating an engaging and supportive learning environment: When teaching subjects such as plagiarism and study skills, the student can easily be constructed as a cheater...

  16. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 6, October 1--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The project involves the construction of an 80,000 gallons per day (260 TPD) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates. At the Eastman complex, the technology will be integrated with existing coal-gasifiers. A carefully developed test plan will allow operations at Eastman to simulate electricity demand load-following in coal-based IGCC facilities. The operations will also demonstrate the enhanced stability and heat dissipation of the conversion process, its reliable on/off operation, and its ability to produce methanol as a clean liquid fuel without additional upgrading. An off-site product testing program will be conducted to demonstrate the suitability of the methanol product as a transportation fuel and as a fuel for stationary applications for small modular electric power generators for distributed power.

  17. A practical technique for the generation of highly uniform LIPSS

    Energy Technology Data Exchange (ETDEWEB)

    Ardron, Marcus, E-mail: ma745@hw.ac.uk [School of Engineering and Physical Sciences, Heriot Watt University, Edinburgh EH14 4AS (United Kingdom); Renishaw PLC, Research Avenue North, Riccarton, Edinburgh EH14 4AP (United Kingdom); Weston, Nick [Renishaw PLC, Research Avenue North, Riccarton, Edinburgh EH14 4AP (United Kingdom); Hand, Duncan [School of Engineering and Physical Sciences, Heriot Watt University, Edinburgh EH14 4AS (United Kingdom)

    2014-09-15

    Highlights: • Formation of uniform LIPSS on stainless steel is greatly aided by polishing in an orthogonal direction to the expected periodic features. Roughness of a sample surface must avoid vector spatial frequency content near to that of the expected LIPSS. • A very simple polishing technique was found to be suitable. • Surface finish requirement was predicted based on the efficacy factor theory; one of the few theories to give qualitatively strong agreement with experimental evidence in a field that is not fully explained by current theories. • Modelled and experimental results presented. • Using a line focused beam from an ultrafast laser facilitated the rapid production of relatively large areas of LIPSS with a modest laser repetition rate. - Abstract: Laser-induced periodic surface structures (LIPSS) can be reliably produced with ultrashort (<10 ps) laser pulses given fluence near the ablation threshold. Neat, parallel, uniform structures are harder to reproduce. Electrodynamic models show a field at normal incidence interacts with the surface resulting in periodicity in intensity along the surface in the direction of the incident E-field producing ridges and toughs on the surface orthogonal to the E-field. A completely smooth surface offers nothing to perturb the eventual periodic feature formation but is very difficult to achieve: we have demonstrated that simply avoiding surface roughness components near the frequency and direction of the emergent features significantly improves uniform feature production. An appropriate unidirectional polishing process can be realised using an inexpensive spinning cloth wheel. By using a cylindrical lens we were also able to process stainless steel surfaces at 5 mm{sup 2} s{sup −1} so indicating useful industrial potential.

  18. DARPA/USAF/USN J-UCAS X-45A System Demonstration Program: A Review of Flight Test Site Processes and Personnel

    Science.gov (United States)

    Cosentino, Gary B.

    2008-01-01

    The Joint Unmanned Combat Air Systems (J-UCAS) program is a collaborative effort between the Defense Advanced Research Project Agency (DARPA), the US Air Force (USAF) and the US Navy (USN). Together they have reviewed X-45A flight test site processes and personnel as part of a system demonstration program for the UCAV-ATD Flight Test Program. The goal was to provide a disciplined controlled process for system integration and testing and demonstration flight tests. NASA's Dryden Flight Research Center (DFRC) acted as the project manager during this effort and was tasked with the responsibilities of range and ground safety, the provision of flight test support and infrastructure and the monitoring of technical and engineering tasks. DFRC also contributed their engineering knowledge through their contributions in the areas of autonomous ground taxi control development, structural dynamics testing and analysis and the provision of other flight test support including telemetry data, tracking radars, and communications and control support equipment. The Air Force Flight Test Center acted at the Deputy Project Manager in this effort and was responsible for the provision of system safety support and airfield management and air traffic control services, among other supporting roles. The T-33 served as a J-UCAS surrogate aircraft and demonstrated flight characteristics similar to that of the the X-45A. The surrogate served as a significant risk reduction resource providing mission planning verification, range safety mission assessment and team training, among other contributions.

  19. GASIS demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Vidas, E.H. [Energy and Environmental Analysis, Inc., Arlington, VA (United States)

    1995-04-01

    A prototype of the GASIS database and retrieval software has been developed and is the subject of this poster session and computer demonstration. The prototype consists of test or preliminary versions of the GASIS Reservoir Data System and Source Directory datasets and the software for query and retrieval. The prototype reservoir database covers the Rocky Mountain region and contains the full GASIS data matrix (all GASIS data elements) that will eventually be included on the CD-ROM. It is populated for development purposes primarily by the information included in the Rocky Mountain Gas Atlas. The software has been developed specifically for GASIS using Foxpro for Windows. The application is an executable file that does not require Foxpro to run. The reservoir database software includes query and retrieval, screen display, report generation, and data export functions. Basic queries by state, basin, or field name will be assisted by scrolling selection lists. A detailed query screen will allow record selection on the basis of any data field, such as depth, cumulative production, or geological age. Logical operators can be applied to any-numeric data element or combination of elements. Screen display includes a {open_quotes}browse{close_quotes} display with one record per row and a detailed single record display. Datasets can be exported in standard formats for manipulation with other software packages. The Source Directory software will allow record retrieval by database type or subject area.

  20. Fast contactless vibrating structure characterization using real time field programmable gate array-based digital signal processing: demonstrations with a passive wireless acoustic delay line probe and vision.

    Science.gov (United States)

    Goavec-Mérou, G; Chrétien, N; Friedt, J-M; Sandoz, P; Martin, G; Lenczner, M; Ballandras, S

    2014-01-01

    Vibrating mechanical structure characterization is demonstrated using contactless techniques best suited for mobile and rotating equipments. Fast measurement rates are achieved using Field Programmable Gate Array (FPGA) devices as real-time digital signal processors. Two kinds of algorithms are implemented on FPGA and experimentally validated in the case of the vibrating tuning fork. A first application concerns in-plane displacement detection by vision with sampling rates above 10 kHz, thus reaching frequency ranges above the audio range. A second demonstration concerns pulsed-RADAR cooperative target phase detection and is applied to radiofrequency acoustic transducers used as passive wireless strain gauges. In this case, the 250 ksamples/s refresh rate achieved is only limited by the acoustic sensor design but not by the detection bandwidth. These realizations illustrate the efficiency, interest, and potentialities of FPGA-based real-time digital signal processing for the contactless interrogation of passive embedded probes with high refresh rates.

  1. UNIFORMITY ASSESSMENT OF CARBON FIBRES DISPERSION IN CEMENT PASTE BY IMPEDANCE MEASUREMENTS

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    An alternating current was applied to measure the impedance of a hardened cement paste with various contents of carbon fibres.When the free water content in the hardened cement paste is 90%-98%,and the measuring frequency 500Hz,an approximate linear relationship was found between fibre content and impedance of the composite.Based on this relationship,a new attempt was made to evaluate the dispersion uniformity of carbon fibres in cement paste by impedance measurement.The standard deviation S and the coefficient of vriation S/(X-)i of impedance of the fibre-cement specimens randomly taken locating in different points were used as main parameters for the uniformity assessment.As a case,four different mixing processes were designed for dispersing carbon fibres into the cement paste.The results demonstrate that the relative longer mixing time increases the dispersion uniformity of carbon fibres in cement paste,and the addition of the water reducer dramatically improves the uniformity due to the change of the fluidity of the paste.The ground fly ash can increase the uniformity to a certain extent.

  2. 均匀水流冲击下扭王字块断裂失稳过程的数值模拟研究%Numerical study on failure process of accropode under the impact of uniform flow

    Institute of Scientific and Technical Information of China (English)

    冯春; 李世海; 赵颖; 刘晓宇

    2014-01-01

    扭王字块是一种重要的港口防波堤护面块体,其断裂失稳过程与所受水流冲击力密切相关。文章以基于连续介质力学的离散元方法(CDEM )为基础,通过引入FVM 算法及半弹簧-半棱联合接触模型,分别实现了大位移下单元变形的准确计算及单元接触的快速更新。基于改进后的CDEM 方法,通过在扭王字块表面施加按流速方向逐渐增加的动态面力,对均匀水流冲击下单扭王字块的断裂过程及扭王字块群的失稳滑移过程进行了数值分析。通过分析,不同方向水流冲击下单扭王字块的主要断裂模式为沿着根部的折断,其断裂流速约为21~25 m/s;不同吨位下扭王字块群的失稳模式为扭王字块单体从群体中跳出,其失稳流速约为4~11 m/s。%Accropode is considered as an important breakwater armour block ,and the failure process is closely related to impact force of flow .Based on Continuum-based Discrete Element Method (CDEM ) , and by introducing FVM algorithm and semi-spring & semi-edge combined contact model ,the precise calculation of element deformation and quick update of element contact under large displacement are real-ized .According to modified CDEM above mentioned ,and by applying gradually increased dynamic face force on accropode surface with the direction of flow ,the numerical simulations are taken .The crack process of single accropode and instability process of accropodes group under impact load of uniform flow are studied .Numerical results show that ,the main crack mode of single accropode is root fracture ,with the crack velocity 20~24 m/s in different impact direction ;and the main instability mode of accropodes group is single accropode jumping out of group ,with the instability velocity 4~12 m/s in different ton-nage .

  3. 均匀设计优化荷叶半仿生提取工艺%Optimization of Semi-Bionic Extraction Process of Lotus Leaf by Uniform Design

    Institute of Scientific and Technical Information of China (English)

    郑丹丹; 刘丽娜; 王京龙; 王占一; 邓艳美

    2016-01-01

    Uniform design was used to optimize semi-bionic extraction( SBE)process of Lotus leaf. The optimum process conditions of semi-bionic extraction of Lotus leaf were studied with total flavonoids and dried extract weight as the index. Be-sides,effects of the pH value and extraction time of the three-time extraction were investigated. Spectrophotography method was conducted to determine the content of total flavonoids. Combined with the industrial production practice,the optimal ex-traction process was as follows:pH value of water in the three-time extraction was 3. 5,6. 5 and 9. 0,with the extraction time of 2. 0 h,1. 5 h and 1. 5h,respectively. The obtained method was easy and simple to operate and the extract rate of total fla-vonoids was relatively high,which provided a theoretical basis for the extraction optimization of Lotus leaf.%采用均匀设计法优选荷叶半仿生提取的最佳工艺条件.本研究以荷叶主要有效成分总黄酮得率以及干浸膏得率为评价指标,对荷叶的半仿生提取工艺条件进行优选,考察三煎pH、提取总时间对荷叶总黄酮提取率的影响,采用分光光度法测定总黄酮的含量.通过优化实验并结合生产实际,确定荷叶半仿生提取的最佳工艺为3煎pH依次为3.5、6.5、9.0,3煎时间依次为2.0 h、1.5 h、1.5 h,所得荷叶总黄酮的提取率为9.7﹪.本法操作简便,提取率较高,为荷叶总黄酮提取工艺的改进提供了理论依据.

  4. Optimization on processing of low-temperature drying of chilled meat by uniform design method%均匀设计法优化冷鲜肉低温干燥工艺

    Institute of Scientific and Technical Information of China (English)

    赵惠麟; 周林

    2014-01-01

    The low-temperature food drying equipment was running at 0-10℃ to simulate the win-ter climate. The chilled meat with little salt and without food additives was dried. Through single factor ex-periment and uniform design method, the optimal processing technology was optimized. The quality differ-ences of product processed by low-temperature drying, natural drying and hot air drying was compared and analyzed. The result showed that the optimal low-temperature drying technology of chilled meat was 60% humidity, dried 72h at 5℃. The quality of product reached the best state with neat appearance, fresh color, cured flavor, smooth taste and modest hardness and the moisture content was 60. 2%. The product processed by low-temperature drying technology had significant advantages compared with natural drying and hot air drying.%利用低温食品干燥机在0~10℃运行,全年模拟冬季气候,用于低盐化无添加风干冷鲜肉,采用单因素实验法和均匀设计法优化了冷鲜肉低温干燥的最佳工艺,并对比分析了低温干燥与自然晾晒及热风干燥两种干燥方式的产品品质差异。结果表明:冷鲜肉的最佳低温干燥工艺为:5℃、60%湿度、干燥72h;产品外观整齐、色泽鲜嫩、腊味浓郁,含水率为60.2%,口感爽滑软硬适中,产品品质达到最佳状态;低温干燥与自然晾晒及热风干燥两种干燥方式相比,低温干燥产品品质优势明显。

  5. On topological spaces possessing uniformly distributed sequences

    CERN Document Server

    Bogachev, V I

    2007-01-01

    Two classes of topological spaces are introduced on which every probability Radon measure possesses a uniformly distributed sequence or a uniformly tight uniformly distributed sequence. It is shown that these classes are stable under multiplication by completely regular Souslin spaces

  6. Sublogarithmic uniform Boolean proof nets

    CERN Document Server

    Aubert, Clément

    2012-01-01

    Using a proofs-as-programs correspondence, Terui was able to compare two models of parallel computation: Boolean circuits and proof nets for multiplicative linear logic. Mogbil et. al. gave a logspace translation allowing us to compare their computational power as uniform complexity classes. This paper presents a novel translation in AC0 and focuses on a simpler restricted notion of uniform Boolean proof nets. We can then encode constant-depth circuits and compare complexity classes below logspace, which were out of reach with the previous translations.

  7. Uniform excitations in magnetic nanoparticles

    DEFF Research Database (Denmark)

    Mørup, Steen; Frandsen, Cathrine; Hansen, Mikkel Fougt

    2010-01-01

    We present a short review of the magnetic excitations in nanoparticles below the superparamagnetic blocking temperature. In this temperature regime, the magnetic dynamics in nanoparticles is dominated by uniform excitations, and this leads to a linear temperature dependence of the magnetization...... and the magnetic hyperfine field, in contrast to the Bloch T3/2 law in bulk materials. The temperature dependence of the average magnetization is conveniently studied by Mössbauer spectroscopy. The energy of the uniform excitations of magnetic nanoparticles can be studied by inelastic neutron scattering....

  8. Uniform excitations in magnetic nanoparticles

    DEFF Research Database (Denmark)

    Mørup, Steen; Frandsen, Cathrine; Hansen, Mikkel Fougt

    2010-01-01

    We present a short review of the magnetic excitations in nanoparticles below the superparamagnetic blocking temperature. In this temperature regime, the magnetic dynamics in nanoparticles is dominated by uniform excitations, and this leads to a linear temperature dependence of the magnetization...... and the magnetic hyperfine field, in contrast to the Bloch T3/2 law in bulk materials. The temperature dependence of the average magnetization is conveniently studied by Mössbauer spectroscopy. The energy of the uniform excitations of magnetic nanoparticles can be studied by inelastic neutron scattering....

  9. Demonstration of a SANEX Process in Centrifugal Contactors using the CyMe{sub 4}-BTBP Molecule on a Genuine Fuel Solution

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, D.; Christiansen, B.; Glatz, J.P.; Malmbeck, R.; Serrano-Purroy, D. [European Commiss, Joint Res Ctr, Inst Transuranium Elements, D-76125 Karlsruhe, (Germany); Foreman, M.R.S. [Univ Reading, Dept Chem, Reading RG6 6AD, Berks, (United Kingdom); Geist, A. [Forschungszentrum Karlsruhe, Inst Nukl Entsorgung, D-76021 Karlsruhe, (Germany); Modolo, G. [Forschungszentrum Julich, Inst Energy Res Safety Res and Reactor Technol, D-52425 Julich, (Germany); Sorel, C. [Commissariat Energie Atom Valrho, CEA, DRCP SCPS, F-30207 Bagnols Sur Ceze, (France)

    2009-07-01

    Efficient recovery of minor actinides from a genuine spent fuel solution has been successfully demonstrated by the CyMe{sub 4}-BTBP/DMDOHEMA extractant mixture dissolved in octanol. The continuous countercurrent process, in which actinides(III) were separated from lanthanides(III), was carried out in laboratory centrifugal contactors using an optimized flow-sheet involving a total of 16 stages. The process was divided into 9 stages for extraction from a 2 M nitric acid feed solution, 3 stages for lanthanide scrubbing, and 4 stages for actinide back-extraction. Excellent feed decontamination factors for Am (7000) and Cm (1000) were obtained and the recoveries of these elements were higher than 99.9%. More than 99.9% of the lanthanides were directed to the raffinate except Gd for which 0.32% was recovered in the product. (authors)

  10. The Power Unit Coordinated Control via Uniform Differential Evolution

    OpenAIRE

    Zain Abdalla Zahran; Rui Feng Shi; Xiang Jie Liu

    2013-01-01

    This paper modified the differential evolution (DE) algorithm adaptively to solve the power unit coordinated control (PUCC) problem. It was modified in two aspects: 1) a uniform initialization, which was controlled and regulated by a zone factor (m), 2) a regular mutation process, to develop an effective searching process and improve the convergence of the basic DE algorithm. A numerical case study was employed to verify the performance of our proposed uniform differential evolution (UDE) a...

  11. A process for polyhydroxyalkanoate (PHA) production from municipal wastewater treatment with biological carbon and nitrogen removal demonstrated at pilot-scale.

    Science.gov (United States)

    Bengtsson, Simon; Karlsson, Anton; Alexandersson, Tomas; Quadri, Luca; Hjort, Markus; Johansson, Peter; Morgan-Sagastume, Fernando; Anterrieu, Simon; Arcos-Hernandez, Monica; Karabegovic, Lamija; Magnusson, Per; Werker, Alan

    2017-03-25

    A process was developed for biological treatment of municipal wastewater for carbon and nitrogen removal while producing added-value polyhydroxyalkanoates (PHAs). The process comprised steps for pre-denitrification, nitrification and post-denitrification and included integrated fixed-film activated sludge (IFAS) with biofilm carrier media to support nitrification. In a pilot-scale demonstration (500-800L), wastewater treatment performance, in line with European standards, were achieved for total chemical oxygen demand (83% removal) and total nitrogen (80% removal) while producing a biomass that was able to accumulate up to 49% PHA of volatile suspended solids with acetic acid or fermented organic residues as substrates. Robust performance in wastewater treatment and enrichment of PHA-producing biomass was demonstrated under realistic conditions including influent variability during 225days of operation. The IFAS system was found to be advantageous since maintaining nitrification on the biofilm allowed for a relatively low (2days) solids retention time (SRT) for the suspended biomass in the bulk phase. Lower SRT has advantages in higher biomass yield and higher active fraction in the biomass which leads to higher PHA productivity and content. The outcomes show that production of added-value biopolymers may be readily integrated with carbon and nitrogen removal from municipal wastewater. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. School Uniforms: Guidelines for Principals.

    Science.gov (United States)

    Essex, Nathan L.

    2001-01-01

    Principals desiring to develop a school-uniform policy should involve parents, teachers, community leaders, and student representatives; beware restrictions on religious and political expression; provide flexibility and assistance for low-income families; implement a pilot program; align the policy with school-safety issues; and consider legal…

  13. Uniformer på arbejde

    DEFF Research Database (Denmark)

    Leilund, Helle

    Afhandlingen , Uniformer på arbejde - nutidige praksisser omkring ensartet arbejdstøj , har afsæt i det kulturhistoriske museums arbejde med ’ dragt ’ . På trods af at ensart et eller uniformt arbejdstøj er et velkendt dagligdags fænomen, som bruges af medarbejdere på mange nutidige arbejdspladser...

  14. Uniform approximation by (quantum) polynomials

    NARCIS (Netherlands)

    Drucker, A.; de Wolf, R.

    2011-01-01

    We show that quantum algorithms can be used to re-prove a classical theorem in approximation theory, Jackson's Theorem, which gives a nearly-optimal quantitative version of Weierstrass's Theorem on uniform approximation of continuous functions by polynomials. We provide two proofs, based respectivel

  15. Uniform Slavic Transliteration Alphabet (USTA).

    Science.gov (United States)

    Dekleva, Borut

    The Uniform Slavic Transliteration Alphabet (USTA) was designed primarily with the following objectives: to aid librarians (catalogers and bibliographers), information scientists, transliterators, and editors of bibliographic works of the many Slavic tongues; and to serve as original research for the further development of a machine-readable…

  16. The best uniform approximation of ellipse with degree two

    Science.gov (United States)

    Rababah, Abedallah; AlMeraj, Zainab

    2017-07-01

    A uniform quadratic approximation of degree 2 is created in explicit parametric form to represent elliptical arcs. The error function is identical to that of the Chebyshev polynomial of degree 4 and equioscillates five times with an approximation order of four. In this paper we provide the approximation method, show it is efficient, its error bound to be accurate and demonstrate that it satisfies properties of the best uniform approximation.

  17. Pulse sequences for uniform perfluorocarbon droplet vaporization and ultrasound imaging.

    Science.gov (United States)

    Puett, C; Sheeran, P S; Rojas, J D; Dayton, P A

    2014-09-01

    Phase-change contrast agents (PCCAs) consist of liquid perfluorocarbon droplets that can be vaporized into gas-filled microbubbles by pulsed ultrasound waves at diagnostic pressures and frequencies. These activatable contrast agents provide benefits of longer circulating times and smaller sizes relative to conventional microbubble contrast agents. However, optimizing ultrasound-induced activation of these agents requires coordinated pulse sequences not found on current clinical systems, in order to both initiate droplet vaporization and image the resulting microbubble population. Specifically, the activation process must provide a spatially uniform distribution of microbubbles and needs to occur quickly enough to image the vaporized agents before they migrate out of the imaging field of view. The development and evaluation of protocols for PCCA-enhanced ultrasound imaging using a commercial array transducer are described. The developed pulse sequences consist of three states: (1) initial imaging at sub-activation pressures, (2) activating droplets within a selected region of interest, and (3) imaging the resulting microbubbles. Bubble clouds produced by the vaporization of decafluorobutane and octafluoropropane droplets were characterized as a function of focused pulse parameters and acoustic field location. Pulse sequences were designed to manipulate the geometries of discrete microbubble clouds using electronic steering, and cloud spacing was tailored to build a uniform vaporization field. The complete pulse sequence was demonstrated in the water bath and then in vivo in a rodent kidney. The resulting contrast provided a significant increase (>15 dB) in signal intensity.

  18. Toward Uniformly Dispersed Battery Electrode Composite Materials: Characteristics and Performance.

    Science.gov (United States)

    Kwon, Yo Han; Huie, Matthew M; Choi, Dalsu; Chang, Mincheol; Marschilok, Amy C; Takeuchi, Kenneth J; Takeuchi, Esther S; Reichmanis, Elsa

    2016-02-10

    Battery electrodes are complex mesoscale systems comprised of electroactive components, conductive additives, and binders. In this report, methods for processing electrodes with dispersion of the components are described. To investigate the degree of material dispersion, a spin-coating technique was adopted to provide a thin, uniform layer that enabled observation of the morphology. Distinct differences in the distribution profile of the electrode components arising from individual materials physical affinities were readily identified. Hansen solubility parameter (HSP) analysis revealed pertinent surface interactions associated with materials dispersivity. Further studies demonstrated that HSPs can provide an effective strategy to identify surface modification approaches for improved dispersions of battery electrode materials. Specifically, introduction of surfactantlike functionality such as oleic acid (OA) capping and P3HT-conjugated polymer wrapping on the surface of nanomaterials significantly enhanced material dispersity over the composite electrode. The approach to the surface treatment on the basis of HSP study can facilitate design of composite electrodes with uniformly dispersed morphology and may contribute to enhancing their electrical and electrochemical behaviors. The conductivity of the composites and their electrochemical performance was also characterized. The study illustrates the importance of considering electronic conductivity, electron transfer, and ion transport in the design of environments incorporating active nanomaterials.

  19. Progress toward Biomass and Coal-Derived Syngas Warm Cleanup: Proof-of-Concept Process Demonstration of Multicontaminant Removal for Biomass Application

    Energy Technology Data Exchange (ETDEWEB)

    Howard, Christopher J.; Dagle, Robert A.; Lebarbier, Vanessa MC; Rainbolt, James E.; Li, Liyu; King, David L.

    2013-06-19

    Systems comprising of multiple sorbent and catalytic beds have been developed for the warm syngas cleanup of coal- and biomass-derived syngas. Tailored specifically for biomass application the process described here consists of six primary unit operations: 1) Na2CO3 bed for HCl removal, 2) two regenerable ZnO beds for bulk H2S removal, 3) ZnO bed for H2S polishing, 4) NiCu/SBA-16 sorbent for trace metal (e.g. AsH3) removal, 5) steam reforming catalyst bed for tars and light hydrocarbons reformation and NH3 decomposition, and a 6) Cu-based LT-WGS catalyst bed. Simulated biomass-derived syngas containing a multitude of inorganic contaminants (H2S, AsH3, HCl, and NH3) and hydrocarbon additives (methane, ethylene, benzene, and naphthalene) was used to demonstrate process effectiveness. The efficiency of the process was demonstrated for a period of 175 hours, during which no signs of deactivation were observed. Post-run analysis revealed small levels of sulfur slipped through the sorbent bed train to the two downstream catalytic beds. Future improvements could be made to the trace metal polishing sorbent to ensure complete inorganic contaminant removal (to low ppb level) prior to the catalytic steps. However, dual, regenerating ZnO beds were effective for continuous removal for the vast majority of the sulfur present in the feed gas. The process was effective for complete AsH3 and HCl removal. The steam reforming catalyst completely reformed all the hydrocarbons present in the feed (methane, ethylene, benzene, and naphthalene) to additional syngas. However, post-run evaluation, under kinetically-controlled conditions, indicates deactivation of the steam reforming catalyst. Spent material characterization suggests this is attributed, in part, to coke formation, likely due to the presence of benzene and/or naphthalene in the feed. Future adaptation of this technology may require dual, regenerable steam reformers. The process and materials described in this report hold

  20. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 5, July 1--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The project involves the construction of an 80,000 gallons per day (260 TPD) methanol unit utilizing coal-derived synthesis gas from Eastman`s integrated coal gasification facility. The new equipment consists of synthesis gas feed preparation and compression facilities, the liquid phase reactor and auxiliaries, product distillation facilities, and utilities. The technology to be demonstrated is the product of a cooperative development effort by Air Products and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} process is ideally suited for directly processing gases produced by modern-day coal gasifiers. Originally tested at a small, DOE-owned experimental unit in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst and allowing the methanol synthesis reaction to proceed at higher rates.

  1. Toward sustainability: a case study demonstrating transdisciplinary learning through the selection and use of indicators in a decision-making process.

    Science.gov (United States)

    Stahl, Cynthia; Cimorelli, Alan; Mazzarella, Christine; Jenkins, Bill

    2011-07-01

    The purpose of this article is to use a case study example to demonstrate how a transparent, transdisciplinary approach to decision making allows the US Environmental Protection Agency Region III (USEPA Region III) to fulfill its decision-making responsibilities while taking critical steps toward engaging in sustainability discussions. The case study goals were to use information about environmental condition to inform staff and fiscal resource prioritization and allocation for the federal 2010 fiscal year. This article will use a select group of 3 indicators to show 1) that data are not the same as indicators, 2) the feasibility of using disparate data in the same analysis, and 3) specific discussions about indicators can lead to transdisciplinary learning, supporting more informed decision making. We show that, when used in a transdisciplinary learning process, these indicator lessons provide a stepping stone for organizations like USEPA Region III to consider sustainability as more than just a lofty, ethical concept. Instead, these kinds of organizations can more routinely and substantively address sustainability through a progression of individual decisions. We discuss how sustainability can be linked to decision making through a process that requires stakeholders to articulate and confront their values. In this process, selecting indicators and understanding what those choices imply regarding the issues that are highlighted and the population affected is part of the assessment of environmental condition, which is the focus of the case study.

  2. Technological assessment of demonstration plants for environmentally compatible processing and utilization of liquid manure. Final report; Technologische Bewertung von Demonstrationsanlagen zur umweltvertraeglichen Guelleaufbereitung und -verwertung. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Weiland, P.; Huettner, A.

    1997-09-01

    The aim of the BMBF-sponsored research programme ``Environmentally compatible liquid manure processing and utilization`` was to develop and test technical processing methods permitting environmentally friendly storage, application and harnessing of liquid manure. For practical testing and optimization, five demonstration plants were erected, which achieve partial or total cleaning of liquid manure by applying different techniques. All processes had the objective of eliminating from the liquid manure nutrients, organic constituents and odourous components, recovering the nutrients in the form of transportable products, and harnessing the liquid manure for biogas generation. (orig.) [Deutsch] Ziel des BMBF-Foerderschwerpunktes `Umweltvertraegliche Guelleaufbereitung und -verwertung` war es, technische Aufbereitungsverfahren zu entwickeln und zu erproben, die eine umweltvertraegliche Lagerung, Ausbringung und Verwertung der Guelle ermoeglichen. Zur Praxiserprobung und Optimierung wurden fuenf Demonstrationsanlagen errichtet, die durch Anwendung unterschiedlicher Verfahren eine Teil- bzw. Totalreinigung der Guelle bewirken. Aufgabe saemtlicher Verfahren war es, die Guelle von Naehrstoffen, organischen Inhaltsstoffen und Geruchsstoffen zu befreien, die Naehrstoffe in Form transportwuerdiger Produkte zurueckzugewinnen und die Guelle durch Erzeugung von Biogas energetisch zu nutzen. (orig.)

  3. Pilot-Scale Demonstration of a Novel, Low-Cost Oxygen Supply Process and its Integration with Oxy-Fuel Coal-Fired Boilers

    Energy Technology Data Exchange (ETDEWEB)

    Krish Krishnamurthy; Divy Acharya; Frank Fitch

    2008-09-30

    In order to achieve DOE targets for carbon dioxide capture, it is crucial not only to develop process options that will generate and provide oxygen to the power cycle in a cost-effective manner compared to the conventional oxygen supply methods based on cryogenic air separation technology, but also to identify effective integration options for these new technologies into the power cycle with carbon dioxide capture. The Linde/BOC developed Ceramic Autothermal Recovery (CAR) process remains an interesting candidate to address both of these issues by the transfer of oxygen from the air to a recycled CO{sub 2} rich flue-gas stream in a cyclic process utilizing the high temperature sorption properties of perovskites. Good progress was made on this technology in this project, but significant challenges remain to be addressed before CAR oxygen production technology is ready for commercial exploitation. Phase 1 of the project was completed by the end of September 2008. The two-bed 0.7 tons/day O2 CAR process development unit (PDU) was installed adjacent to WRI's pilot scale coal combustion test facility (CTF). Start-up and operating sequences for the PDU were developed and cyclic operation of the CAR process demonstrated. Controlled low concentration methane addition allowed the beds to be heated up to operational temperature (800-900 C) and then held there during cyclic operation of the 2-bed CAR process, in this way overcoming unavoidable heat losses from the beds during steady state operation. The performance of the PDU was optimized as much as possible, but equipment limitations prevented the system from fully achieving its target performance. Design of the flue gas recirculation system to integrate CAR PDU with the CTF and the system was completed and integrated tests successfully performed at the end of the period. A detailed techno-economic analysis was made of the CAR process for supplying the oxygen in oxy-fuel combustion retrofit option using AEP's 450

  4. 热镀锌过程挡板对镀层均匀性影响的模拟研究%Computational studies on coating uniformity influenced by baffle in hot dip galvanizing process

    Institute of Scientific and Technical Information of China (English)

    富聿晶; 张红梅; 李培兴; 赵红阳

    2015-01-01

    为解决热镀锌过程中常出现的边部过镀锌缺陷,利用数值模拟方法对热镀锌气刀射流喷吹过程进行仿真研究,分析了挡板厚度对带钢边部压力场的影响;并借助镀层厚度计算模型,计算挡板厚度和边部角度对镀层厚度的作用关系;同时通过不同拉钢速度、气刀狭缝总压等工况,对挡板的厚度及边部角度进行优化。结果表明:随挡板厚度减小,带钢边部作用力增大并逐渐接近中心处;带钢边部镀层厚度随挡板厚度的减小而变薄,随挡板边部角度的增加而先减小后增大;挡板厚度2 mm、边部角度90°时,能有效提高带钢横向作用力和镀层分布的均匀性。%Numerical simulation of the gas⁃jet wiping in hot dip galvanizing process was conducted, aiming to reduce the possible of edge over coating ( EOC) . The effects of baffle thickness and edge angle on pressure fields of strip edge were studied. By using the analytic model of film thickness, the correlation betweent the coating thickness and baffle thickness and edge angle was revealed. Considering different conditions of steel moving speed and total gas knife pressure, the baffle thickness and edge angle were optimized .The results show that the coating thickness of strip edge increases with the decrease of baffle thickness. In addition, with the increase of baffle edge angle, the coating thickness decreases firstly and then increases. When the baffle thickness is 2 mm and the angle is 90°, uniformity distribution of the pressure and coating on the strip is achieved.

  5. Uniformity Analysis for Index of Retail Price

    Institute of Scientific and Technical Information of China (English)

    潘竞红; 曾庆洪; 刘梅英

    2002-01-01

    Using the Hodges-Ajne testing method, the uniformity of China retail price index was tested. The result, that population is submitting to uniform dist ribution, was obtained. The uniformity of CRPI indicates that the general price level is stable in the Ninth Five-Year Plan. Finally, the reasons causing the uniformity was analyzed.

  6. 46 CFR 310.11 - Cadet uniforms.

    Science.gov (United States)

    2010-10-01

    ... for State, Territorial or Regional Maritime Academies and Colleges § 310.11 Cadet uniforms. Cadet uniforms shall be supplied at the school in accordance with the uniform regulations of the School. Those... 46 Shipping 8 2010-10-01 2010-10-01 false Cadet uniforms. 310.11 Section 310.11 Shipping...

  7. Efficient Analysis of Surface-Wire Configurations Using AIM and Best Uniform Rational Approximation

    Institute of Scientific and Technical Information of China (English)

    DONG Hailin; GONG Shuxi; WANG Xing; ZHANG Penfei; ZHAO Bo

    2015-01-01

    The Adaptive integral method (AIM) in conjunction with the best uniform approximation tech-nique is applied to analyze the electromagnetic problems of surface-wire junction geometries over a wide frequency band. To improve the computation efficiency, the best uniform approximation method is utilized. The AIM can reduce memory requirements and accelerate the matrix-vector multiplications in iterative process. Some numeri-cal examples are shown to demonstrate the efficiency and accuracy of the proposed method. Compared with the di-rect solution method and Asymptotic waveform evaluation (AWE) technique, the proposed technique is found to be efficient in a broadband with the lower Central processing unit (CPU) time required and without loss of accuracy.

  8. Weak, strong, and uniform quantum simulations

    Science.gov (United States)

    Wang, Dong-Sheng

    2015-01-01

    In this work, we introduce different types of quantum simulations according to different operator topologies on a Hilbert space, namely, uniform, strong, and weak quantum simulations. We show that they have the same computational power that the efficiently solvable problems are in bounded-error quantum polynomial time. For the weak simulation, we formalize a general weak quantum simulation problem and construct an algorithm which is valid for all instances. Also, we analyze the computational power of quantum simulations by proving the query lower bound for simulating a general quantum process.

  9. Uniform Approximation of Vapnik-Chervonenkis Classes

    CERN Document Server

    Adams, Terrence M

    2010-01-01

    For any family of measurable sets in a probability space, we show that either (i) the family has infinite Vapnik-Chervonenkis (VC) dimension or (ii) for every epsilon > 0 there is a finite partition pi such the pi-boundary of each set has measure at most epsilon. Immediate corollaries include the fact that a family with finite VC dimension has finite bracketing numbers, and satisfies uniform laws of large numbers for every ergodic process. From these corollaries, we derive analogous results for VC major and VC graph families of functions.

  10. Processus empirique des rapports de $m$-espacements uniformes disjoints

    CERN Document Server

    Jérémie, Moïse

    2011-01-01

    We consider an empirical process based upon ratio of selected pair of the non-overlapping spacings generated by independent samples of arbitrary sizes. As a main result we show that when both samples are uniformly distributed on intervals of equal lengths, this empirical process converges to a gaussian process limiting, which we specify the structure when the sample sizes tend to infinity.

  11. High consistency forming process for paper making. Part 1. A research, development, and demonstration program plan for the US Papermaking Industry. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-04-01

    The subject of research, development, and demonstration (RD and D) of energy conserving technologies applicable to papermaking operations downstream of the pulping process is addressed. An RD and D Program Plan is presented based on a survey of leading representatives of the papermaking industry, equipment manufacturers, consulting engineering firms, the American Paper Institute, and the Technical Association of the Pulp and Paper Industry. For perspective, the program plan is presented against the general background of the industry's current issues and concerns. The second part of the paper, Phase I, final report, deals with papermaking test facilities. The case for a centralized test facility is discussed. The results of a survey of existing pilot paper machines are presented. The energy saving potential of high consistency forming is considered and related to existing evidence. Simple theoretical models for the press nip action and the drying process are developed to predict where high consistency forming will reduce energy consumption. A special dynamic former has been designed, fabricated, and commissioned to allow development of a laboratory high consistency headbox. The design and construction of a low speed headbox has been completed and the complete system operated. Special equipment and techniques for the measurement of the water and air permeability of sheet samples have been developed and are described.

  12. Uniformity microsprinkler irrigation system using statistical quality control

    Directory of Open Access Journals (Sweden)

    Maurício Guy de Andrade

    Full Text Available ABSTRACT: The objective of this study was to evaluate the use of statistical quality control tools in the analysis of the uniformity of a microsprinkler irrigation system. For the analysis of irrigation Christiansen uniformity coefficient (CUC and the distribution uniformity coefficient (DU were statistically analyzed by means of the Shewhart control charts and process capability index (Cp. For the experiment 25 tests were carried out with a single micro sprinkler and subsequently seven different spacing between micro sprinklers were simulated. Control charts contributed to the diagnosis of the treatments to be under control and with satisfactory uniformity outcomes. Increase in process capability index was directly proportional to the average of CUC and DU.

  13. Demonstration of a Universal Solvent Extraction Process for the Separation of Cesium and Strontium from Actual Acidic Tank Waste at the INEEL

    Energy Technology Data Exchange (ETDEWEB)

    Law, Jack Douglas; Herbst, Ronald Scott; Todd, Terry Allen; Brewer, Ken Neal; Romanovskiy, V.N.; Esimantovskiy, V.M.; Smirnov, I.V.; Babain, V.A.; Zaitsev, B.N.

    1999-09-01

    A universal solvent extraction process is being evaluated for the simultaneous separation of Cs, Sr, and the actinides from acidic high-activity tank waste at the Idaho National Engineering and Environmental Laboratory (INEEL) with the goal of minimizing the high-activity waste volume to be disposed in a deep geological repository. The universal solvent extraction process is being developed as a collaborative effort between the INEEL and the Khlopin Radium Institute in St. Petersburg, Russia. The process was recently demonstrated at the INEEL using actual radioactive, acidic tank waste in 24 stages of 2-cm diameter centrifugal contactors located in a shielded cell facility. With this testing, removal efficiencies of 99.95%, 99.985%, and 95.2% were obtained for 137 Cs, 90 Sr, and total alpha, respectively. This is sufficient to reduce the activities of 137 Cs and 90 Sr to below NRC Class A LLW requirements. The total alpha removal efficiency was not sufficient to reduce the activity of the tank waste to below NRC Class A non-TRU requirements. The lower than expected removal efficiency for the actinides is due to loading of the Ph2Bu2CMPO in the universal solvent exiting the actinide strip section and entering the wash section resulted in the recycle of the actinides back to the extraction section. This recycle of the actinides contributed to the low removal efficiency. Significant amounts of the Zr (>97.7%), Ba (>87%), Pb (>98.5%), Fe (6.9%), Mo (19%), and K (17%) were also removed from the feed with the universal solvent extraction flowsheet.

  14. Local self-uniformity in photonic networks

    Science.gov (United States)

    Sellers, Steven R.; Man, Weining; Sahba, Shervin; Florescu, Marian

    2017-01-01

    The interaction of a material with light is intimately related to its wavelength-scale structure. Simple connections between structure and optical response empower us with essential intuition to engineer complex optical functionalities. Here we develop local self-uniformity (LSU) as a measure of a random network's internal structural similarity, ranking networks on a continuous scale from crystalline, through glassy intermediate states, to chaotic configurations. We demonstrate that complete photonic bandgap structures possess substantial LSU and validate LSU's importance in gap formation through design of amorphous gyroid structures. Amorphous gyroid samples are fabricated via three-dimensional ceramic printing and the bandgaps experimentally verified. We explore also the wing-scale structuring in the butterfly Pseudolycaena marsyas and show that it possesses substantial amorphous gyroid character, demonstrating the subtle order achieved by evolutionary optimization and the possibility of an amorphous gyroid's self-assembly. PMID:28211466

  15. Uniform and Non-Uniform Single Image Deblurring Based on Sparse Representation and Adaptive Dictionary Learning

    Directory of Open Access Journals (Sweden)

    Ashwini M. Deshpande

    2014-02-01

    Full Text Available Considering the sparseness property of images, a sparse representation based iterative deblurring method is presented for single image deblurring under uniform and non-uniform motion blur. The approach taken is based on sparse and redundant representations over adaptively training dictionaries from single blurred-noisy image itself. Further, the K-SVD algorithm is used to obtain a dictionary that describes the image contents effectively. Comprehensive experimental evaluation demonstrate that the proposed framework integrating the sparseness property of images, adaptive dictionary training and iterative deblurring scheme together significantly improves the deblurring performance and is comparable with the state-of-the art deblurring algorithms and seeks a powerful solution to an ill-conditioned inverse problem.

  16. A Non-Uniformly Under-Sampled Blade Tip-Timing Signal Reconstruction Method for Blade Vibration Monitoring

    Directory of Open Access Journals (Sweden)

    Zheng Hu

    2015-01-01

    Full Text Available High-speed blades are often prone to fatigue due to severe blade vibrations. In particular, synchronous vibrations can cause irreversible damages to the blade. Blade tip-timing methods (BTT have become a promising way to monitor blade vibrations. However, synchronous vibrations are unsuitably monitored by uniform BTT sampling. Therefore, non-equally mounted probes have been used, which will result in the non-uniformity of the sampling signal. Since under-sampling is an intrinsic drawback of BTT methods, how to analyze non-uniformly under-sampled BTT signals is a big challenge. In this paper, a novel reconstruction method for non-uniformly under-sampled BTT data is presented. The method is based on the periodically non-uniform sampling theorem. Firstly, a mathematical model of a non-uniform BTT sampling process is built. It can be treated as the sum of certain uniform sample streams. For each stream, an interpolating function is required to prevent aliasing in the reconstructed signal. Secondly, simultaneous equations of all interpolating functions in each sub-band are built and corresponding solutions are ultimately derived to remove unwanted replicas of the original signal caused by the sampling, which may overlay the original signal. In the end, numerical simulations and experiments are carried out to validate the feasibility of the proposed method. The results demonstrate the accuracy of the reconstructed signal depends on the sampling frequency, the blade vibration frequency, the blade vibration bandwidth, the probe static offset and the number of samples. In practice, both types of blade vibration signals can be particularly reconstructed by non-uniform BTT data acquired from only two probes.

  17. Image Correlation Microscopy for Uniform Illumination

    Science.gov (United States)

    Gaborski, Thomas R.; Sealander, Michael N.; Ehrenberg, Morton; Waugh, Richard E.; McGrath, James L.

    2011-01-01

    Image cross-correlation microscopy (ICM) is a technique that quantifies the motion of fluorescent features in an image by measuring the temporal autocorrelation function decay in a time-lapse image sequence. ICM has traditionally employed laser-scanning microscopes because the technique emerged as an extension of laser-based fluorescence correlation spectroscopy (FCS). In this work, we show that image correlation can also be used to measure fluorescence dynamics in uniform illumination or wide-field imaging systems and we call our new approach uniform illumination image correlation microscopy (UI-ICM). Wide-field microscopy is not only a simpler, less expensive imaging modality, but it offers the capability of greater temporal resolution over laser-scanning systems. In traditional laser-scanning ICM, lateral mobility is calculated from the temporal de-correlation of an image, where the characteristic length is the illuminating laser beam width. In wide-field microscopy, the diffusion length is defined by the feature size using the spatial autocorrelation function (SACF). Correlation function decay in time occurs as an object diffuses from its original position. We show that theoretical and simulated comparisons between Gaussian and uniform features indicate the temporal autocorrelation function (TACF) depends strongly on particle size and not particle shape. In this report, we establish the relationships between the SACF feature size, TACF characteristic time and the diffusion coefficient for UI-ICM using analytical, Monte-Carlo and experimental validation with particle tracking algorithms. Additionally, we demonstrate UI-ICM analysis of adhesion molecule domain aggregation and diffusion on the surface of human neutrophils. PMID:20055917

  18. Thomas Precession by Uniform Acceleration

    CERN Document Server

    Pardy, Miroslav

    2015-01-01

    We determine the nonlinear transformations between coordinate systems which are mutually in a constant symmetrical accelerated motion. The maximal acceleration limit follows from the kinematical origin and it is an analogue of the maximal velocity in special relativity. We derive the dependence of mass, length, time, Doppler effect, Cherenkov effect and transition radiation angle on acceleration as an analogue phenomena in special theory of relativity. The last application of our method is the Thomas precession by uniform acceleration with the possible role in the modern physics and cosmology. The comparison of derived results with other relativistic methods is necessary.

  19. Non-uniform sediment incipient velocity

    Institute of Scientific and Technical Information of China (English)

    Haitao XU; Jinyou LU; Xiaobin LIU

    2008-01-01

    Based on the mechanism of non-uniform sediment incipient motion,the dragging force and uplift force coefficient expressions are put forward for the non-uniform bed material exposure and close alignment state.The incipient veiocity formula of the non-uniform sediment is then established.It is shown that the formula structure is reasonable,and fine particles of the non-uniform sediment are more difficult to set into motion than the same sized uniform particles,whereas coarser particles are easier to set into motion than their uniform equivalents.The validity of the formula is verified by field and experiment data.

  20. Gravitational memory for uniformly accelerated observers

    Science.gov (United States)

    Kolekar, Sanved; Louko, Jorma

    2017-07-01

    Recently, Hawking, Perry and Strominger described a physical process that implants supertranslational hair on a Schwarzschild black hole by an infalling matter shock wave without spherical symmetry. Using the Bondi-Metzner-Sachs-type symmetries of the Rindler horizon, we present an analogous process that implants supertranslational hair on a Rindler horizon by a matter shock wave without planar symmetry, and we investigate the corresponding memory effect on the Rindler family of uniformly linearly accelerated observers. We assume each observer to remain linearly uniformly accelerated through the wave, in the sense of the curved spacetime generalization of the Letaw-Frenet equations. Starting with a family of observers who follow the orbits of a single boost Killing vector before the wave, we find that after the wave has passed, each observer still follows the orbit of a boost Killing vector but this boost differs from trajectory to trajectory, and the trajectory dependence carries a memory of the planar inhomogeneity of the wave. We anticipate this classical memory phenomenon to have a counterpart in Rindler space quantum field theory.

  1. Real-Time On-Board Airborne Demonstration of High-Speed On-Board Data Processing for Science Instruments (HOPS)

    Science.gov (United States)

    Beyon, Jeffrey Y.; Ng, Tak-Kwong; Davis, Mitchell J.; Adams, James K.; Bowen, Stephen C.; Fay, James J.; Hutchinson, Mark A.

    2015-01-01

    The project called High-Speed On-Board Data Processing for Science Instruments (HOPS) has been funded by NASA Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST) program since April, 2012. The HOPS team recently completed two flight campaigns during the summer of 2014 on two different aircrafts with two different science instruments. The first flight campaign was in July, 2014 based at NASA Langley Research Center (LaRC) in Hampton, VA on the NASA's HU-25 aircraft. The science instrument that flew with HOPS was Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) CarbonHawk Experiment Simulator (ACES) funded by NASA's Instrument Incubator Program (IIP). The second campaign was in August, 2014 based at NASA Armstrong Flight Research Center (AFRC) in Palmdale, CA on the NASA's DC-8 aircraft. HOPS flew with the Multifunctional Fiber Laser Lidar (MFLL) instrument developed by Excelis Inc. The goal of the campaigns was to perform an end-to-end demonstration of the capabilities of the HOPS prototype system (HOPS COTS) while running the most computationally intensive part of the ASCENDS algorithm real-time on-board. The comparison of the two flight campaigns and the results of the functionality tests of the HOPS COTS are presented in this paper.

  2. 100 GHz Demonstrations Based on the Single-Flux-Quantum Cell Library for the 10 kA/cm2 Nb Multi-Layer Process

    Science.gov (United States)

    Yamanashi, Yuki; Kainuma, Toshiki; Yoshikawa, Nobuyuki; Kataeva, Irina; Akaike, Hiroyuki; Fujimaki, Akira; Tanaka, Masamitsu; Takagi, Naofumi; Nagasawa, Shuichi; Hidaka, Mutsuo

    A single flux quantum (SFQ) logic cell library has been developed for the 10kA/cm2 Nb multi-layer fabrication process to efficiently design large-scale SFQ digital circuits. In the new cell library, the critical current density of Josephson junctions is increased from 2.5kA/cm2 to 10kA/cm2 compared to our conventional cell library, and the McCumber-Stwart parameter of each Josephson junction is increased to 2 in order to increase the circuit operation speed. More than 300 cells have been designed, including fundamental logic cells and wiring cells for passive interconnects. We have measured all cells and confirmed they stably operate with wide operating margins. On-chip high-speed test of the toggle flip-flop (TFF) cell has been performed by measuring the input and output voltages. The TFF cell at the input frequency of up to 400GHz was confirmed to operate correctly. Also, several fundamental digital circuits, a 4-bit concurrent-flow shift register and a bit-serial adder have been designed using the new cell library, and the correct operations of the circuits have been demonstrated at high clock frequencies of more than 100GHz.

  3. Uniform generation of combinatorial structures

    Energy Technology Data Exchange (ETDEWEB)

    Zito, M.; Pu, I.; Amos, M.; Gibbons, A. [Univ. of Warwick, Coventry (United Kingdom)

    1996-12-31

    We describe several RNC algorithms for generating graphs and subgraphs uniformly at random. For example, unlabelled undirected graphs are generated in O(log{sup 3} n lg lg n) time using O({epsilon}n{sup 1.5}/lg{sup 3} n lg lg n) processors if their number is n lg lg n known in advance and in O(lg n) time using O ({epsilon}n{sup 2}/lg n) processors otherwise. In both cases the error probability is the inverse of a polynomial in {epsilon}. Thus {epsilon} may be chosen to trade-off processors for error probability. Also, for an arbitrary graph, we describe RNC algorithms for the uniform generation of its subgraphs that are either non-simple paths or spanning trees. The work measure for the subgraph algorithms is essentially determined by the transitive closure bottleneck. As for sequential algorithms, the general notion of constructing generators from counters also applies to parallel algorithms although this approach is not employed by all the algorithms of this paper.

  4. LIMB Demonstration Project Extension and Coolside Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Goots, T.R.; DePero, M.J.; Nolan, P.S.

    1992-11-10

    This report presents results from the limestone Injection Multistage Burner (LIMB) Demonstration Project Extension. LIMB is a furnace sorbent injection technology designed for the reduction of sulfur dioxide (SO[sub 2]) and nitrogen oxides (NO[sub x]) emissions from coal-fired utility boilers. The testing was conducted on the 105 Mwe, coal-fired, Unit 4 boiler at Ohio Edison's Edgewater Station in Lorain, Ohio. In addition to the LIMB Extension activities, the overall project included demonstration of the Coolside process for S0[sub 2] removal for which a separate report has been issued. The primary purpose of the DOE LIMB Extension testing, was to demonstrate the generic applicability of LIMB technology. The program sought to characterize the S0[sub 2] emissions that result when various calcium-based sorbents are injected into the furnace, while burning coals having sulfur content ranging from 1.6 to 3.8 weight percent. The four sorbents used included calcitic limestone, dolomitic hydrated lime, calcitic hydrated lime, and calcitic hydrated lime with a small amount of added calcium lignosulfonate. The results include those obtained for the various coal/sorbent combinations and the effects of the LIMB process on boiler and plant operations.

  5. A Systematic Approach of Employing Quality by Design Principles: Risk Assessment and Design of Experiments to Demonstrate Process Understanding and Identify the Critical Process Parameters for Coating of the Ethylcellulose Pseudolatex Dispersion Using Non-Conventional Fluid Bed Process.

    Science.gov (United States)

    Kothari, Bhaveshkumar H; Fahmy, Raafat; Claycamp, H Gregg; Moore, Christine M V; Chatterjee, Sharmista; Hoag, Stephen W

    2016-07-14

    The goal of this study was to utilize risk assessment techniques and statistical design of experiments (DoE) to gain process understanding and to identify critical process parameters for the manufacture of controlled release multiparticulate beads using a novel disk-jet fluid bed technology. The material attributes and process parameters were systematically assessed using the Ishikawa fish bone diagram and failure mode and effect analysis (FMEA) risk assessment methods. The high risk attributes identified by the FMEA analysis were further explored using resolution V fractional factorial design. To gain an understanding of the processing parameters, a resolution V fractional factorial study was conducted. Using knowledge gained from the resolution V study, a resolution IV fractional factorial study was conducted; the purpose of this IV study was to identify the critical process parameters (CPP) that impact the critical quality attributes and understand the influence of these parameters on film formation. For both studies, the microclimate, atomization pressure, inlet air volume, product temperature (during spraying and curing), curing time, and percent solids in the coating solutions were studied. The responses evaluated were percent agglomeration, percent fines, percent yield, bead aspect ratio, median particle size diameter (d50), assay, and drug release rate. Pyrobuttons® were used to record real-time temperature and humidity changes in the fluid bed. The risk assessment methods and process analytical tools helped to understand the novel disk-jet technology and to systematically develop models of the coating process parameters like process efficiency and the extent of curing during the coating process.

  6. Uniformly accelerated observer in a thermal bath

    CERN Document Server

    Kolekar, Sanved

    2013-01-01

    We investigate the quantum field aspects in flat spacetime for an uniformly accelerated observer moving in a thermal bath. In particular, we obtain an exact closed expression of the reduced density matrix for an uniformly accelerated observer with acceleration $a = 2\\pi T$ when the state of the quantum field is a thermal bath at temperature $T^\\prime$. We find that the density matrix has a simple form with an effective partition function $Z$ being a product, $Z = Z_T Z_{T^\\prime}$, of two thermal partition functions corresponding to temperatures $T$ and $T^\\prime$ and hence is not thermal, even when $T = T^\\prime$. We show that, even though the partition function has a product structure, the two thermal baths are, in fact, interacting systems; although in the high frequency limit $\\omega_k \\gg T$ and $\\omega_k \\gg T^\\prime$, the interactions are found to become sub-dominant. We further demonstrate that the resulting spectrum of the Rindler particles can be interpreted in terms of spontaneous and stimulated em...

  7. Practical Non-Uniform Channelization for Multistandard Base Stations

    Institute of Scientific and Technical Information of China (English)

    Alvaro Palomo Navarro; Rudi Villing; Ronan J. Farrell

    2011-01-01

    A multistandard software-defined radio base station must perform non-uniform channelization of multiplexed frequency bands. Non-uniform channelization accounts for a significant portion of the digital signal processing workload in the base station receiver and can be difficult to realize in a physical implementation. In non-uniform channelization methods based on generalized DFT filter banks, large prototype filter orders are a significant issue for implementation. In this paper, a multistage filter design is applied to two different non-uniform generalized DFT-based channelizers in order to reduce their filter orders. To evaluate the approach, a TETRA and TEDS base station is used. Experimental results show that the new multistage design reduces both the number of coefficients and operations and leads to a more feasible design and practical physical implementation.

  8. Calculation of Uniform of Beam Scanning

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    For the electron beam application, it is always scanned by a dipole magnet. The uniform of the scanning has great influence for some application, such as the irradiation of the thyristor. There are two methods for improving the scanning uniform:

  9. Direction of Arrival Estimation Based on MUSIC Algorithm Using Uniform and Non-Uniform Linear Arrays

    Directory of Open Access Journals (Sweden)

    Eva Kwizera

    2017-03-01

    Full Text Available In signal processing, the direction of arrival (DOA estimation denotes the direction from which a propagating wave arrives at a point, where a set of antennas is located. Using the array antenna has an advantage over the single antenna in achieving an improved performance by applying Multiple Signal Classification (MUSIC algorithm. This paper focuses on estimating the DOA using uniform linear array (ULA and non-uniform linear array (NLAof antennas to analyze the performance factors that affect the accuracy and resolution of the system based on MUSIC algorithm. The direction of arrival estimation is simulated on a MATLAB platform with a set of input parameters such as array elements, signal to noise ratio, number of snapshots and number of signal sources. An extensive simulation has been conducted and the results show that the NLA with DOA estimation for co-prime array can achieve an accurate and efficient DOA estimation

  10. Uniform temperature profile for a dense array CPV receiver under non uniform illumination profile

    Science.gov (United States)

    Riera, Sara; Barrau, Jérôme; Perona, Arnaud; Dollet, Alain; Rosell, Joan I.; Fréchette, Luc

    2014-09-01

    Previous experimental and numerical studies of hybrid cooling devices for CPV receivers were developed under uniform illumination profile conditions; but literature review shows that this uniformity assumption is difficult to satisfy in real conditions. This investigation presents the design and the validation of a hybrid cooling device able to tailor its local heat extraction capacity to 2D illumination profiles in order to provide a uniform temperature profile of the PV receiver as well as a low global thermal resistance coefficient. The inputs of the design procedure are the solar concentration, the coolant flow rate and its inlet temperature. As the illumination profile is 2D dependent, a matrix of pin fins is implemented and a hybrid Jet Impingement /Matrix of Pin Fins cooling device is experimentally tested and compared to a hybrid Jet Impingement / Microchannels cooling device developed previously. The results demonstrate similar performances for both designs. Furthermore, in contrast to the cooling scheme using longitudinal fins, the distribution of the pin fins can be tailored, in two dimensions, to the local need of heat extraction capacity.

  11. Extending maps between pre-uniform spaces

    OpenAIRE

    Adalberto García-Máynez; Rubén Mancio-Toledo

    2012-01-01

    We give sufficient conditions on a uniformly continuous map f: (X,U) → (Y, V ) between completable T1-pre-uniform spaces (X,U), (Y, V ) to have a continuous or a uniformly continuous extension f:X → Y between the corresponding completions.

  12. Attitudes of Parents about School Uniforms.

    Science.gov (United States)

    West, Charles K.; Tidwell, Diane K.; Bomba, Anne K.; Elmore, Patsy Alexander

    1999-01-01

    Responses from 144 parents of fourth graders showed that 56% favored uniforms in public schools; most agreed that uniforms contributed to a conducive learning environment, promoted school spirit, and discouraged violence; and most disagreed that uniforms cost more than other types of clothing. (SK)

  13. Commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) process. Technical progress report number 11, January 1--March 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-11

    During this quarter, the third draft of the Topical Report on Process Economics Studies was issued for review. A recommendation to continue with design verification testing on the coproduction of methanol and dimethyl ether (DME) was made. A liquid phase dimethyl ether (LPDME) catalyst system with reasonable long-term activity and stability is being developed, and a decision to proceed with a proof-of-concept test run at the LaPorte Alternative Fuels Development Unit (AFDU) is pending the release of a memo from Air Products on the catalyst targets and corresponding economics for a commercially successful LPDME catalyst. The off-site product-use test plan is to be updated in June of 1997. During this quarter, Air Products and Acurex Environmental Corporation continued developing the listing of product-use test participants who are involved in fuel cell, transportation, and stationary power plant applications. Start-up activities (Task 3.1) began during the reporting period, and coal-derived synthesis gas (syngas) was introduced to the demonstration unit. The recycle compressor was tested successfully on syngas at line pressure of 700 psig, and the reactor loop reached 220 C for carbonyl burnout. Iron carbonyl in the balanced gas feed remained below the 10 ppbv detection limit for all samples but one. Within the reactor loop, iron carbonyl levels peaked out near 200 ppbv after about 40 hours on-stream, before decreasing to between 10--20 ppbv at 160 hours on -stream. Nickel carbonyl measurements reached a peak of about 60 ppbv, and decreased at all sampling locations to below the 10 ppbv detection limit by 70 hours on-stream. Catalyst activation of the nine 2,250 lb batches required for the initial catalyst charge began and concluded. All batches met or slightly exceeded the theoretical maximum uptake of 2.82 SCF of reducing gas/lb catalyst.

  14. Uniform magnetic excitations in nanoparticles

    DEFF Research Database (Denmark)

    Mørup, Steen; Hansen, Britt Rosendahl

    2005-01-01

    We have used a spin-wave model to calculate the temperature dependence of the (sublattice) magnetization of magnetic nanoparticles. The uniform precession mode, corresponding to a spin wave with wave vector q=0, is predominant in nanoparticles and gives rise to an approximately linear temperature...... dependence of the (sublattice) magnetization well below the superparamagnetic blocking temperature for both ferro-, ferri-, and antiferromagnetic particles. This is in accordance with the results of a classical model for collective magnetic excitations in nanoparticles. In nanoparticles of antiferromagnetic...... materials, quantum effects give rise to a small deviation from the linear temperature dependence of the (sublattice) magnetization at very low temperatures. The complex nature of the excited precession states of nanoparticles of antiferromagnetic materials, with deviations from antiparallel orientation...

  15. BASIS WEIGHT UNIFORMITY OF LIGHTLY NEEDLED HYDROENTANGLED COTTON AND COTTON BLEND WEBS

    Directory of Open Access Journals (Sweden)

    D.V. Parikh

    2006-08-01

    Full Text Available New nonwoven products containing cotton and Lyocell (Trademarked name Tencel, low temperature thermal-bondable bicomponent olefin/polyester, or comber noils were developed using needlepunching and spunlacing (hydroentanglement. Webs containing five different blends were prepared by either light needlepunching, or light needlepunching followed by hydroentangling. We acquired detailed basis weight uniformity measurements to learn about processing and the influence of fiber blend composition on web uniformity. Basis weight uniformity was evaluated without regard to web direction ("Total" uniformity, along the machine direction (MD uniformity and across the cross direction (CD uniformity at numerous size resolutions. We observed that blending manufactured fibers (either Tencel or olefin/polyester with bleached cotton and comber noils substantially improved basis weight uniformity of both types of nonwovens. We also observed that subjecting needled webs to hydroentangling significantly improved Total and MD uniformities.

  16. Investigation of multiple spindle characteristics under non-uniform bearing preload

    Directory of Open Access Journals (Sweden)

    Yanfei Zhang

    2016-02-01

    Full Text Available The non-uniform distribution load during machining and assembly process is crucial for spindle system, especially in complex working conditions. The conception of non-uniform preload adjustment approach was proposed and experimentally investigated in this article. Based on the mechanical equivalent principle, the non-uniform preload was theoretically transformed to the combination of uniform preload and an extra moment. Then, the non-uniform preload of rolling bearing was experimentally measured and analyzed via a spacer with 15-µm wear loss on the end face. The spindle performance factors, such as rotation accuracy, temperature rising, acceleration, and vibration, were all monitored. The rotation center of spindle was deviated in different non-uniform preload conditions. Meanwhile, the temperature and vibration performance of non-uniform preload are superior to those of uniform bearing preload.

  17. Uniform convergence of Vapnik--Chervonenkis classes under ergodic sampling

    CERN Document Server

    Adams, Terrence M; 10.1214/09-AOP511

    2010-01-01

    We show that if $\\mathcal{X}$ is a complete separable metric space and $\\mathcal{C}$ is a countable family of Borel subsets of $\\mathcal{X}$ with finite VC dimension, then, for every stationary ergodic process with values in $\\mathcal{X}$, the relative frequencies of sets $C\\in\\mathcal{C}$ converge uniformly to their limiting probabilities. Beyond ergodicity, no assumptions are imposed on the sampling process, and no regularity conditions are imposed on the elements of $\\mathcal{C}$. The result extends existing work of Vapnik and Chervonenkis, among others, who have studied uniform convergence for i.i.d. and strongly mixing processes. Our method of proof is new and direct: it does not rely on symmetrization techniques, probability inequalities or mixing conditions. The uniform convergence of relative frequencies for VC-major and VC-graph classes of functions under ergodic sampling is established as a corollary of the basic result for sets.

  18. Calculus Demonstrations Using MATLAB

    Science.gov (United States)

    Dunn, Peter K.; Harman, Chris

    2002-01-01

    The note discusses ways in which technology can be used in the calculus learning process. In particular, five MATLAB programs are detailed for use by instructors or students that demonstrate important concepts in introductory calculus: Newton's method, differentiation and integration. Two of the programs are animated. The programs and the…

  19. 基于GUI的数字信号处理课程演示系统研究%Demonstration system of digital signal processing course based on GUI

    Institute of Scientific and Technical Information of China (English)

    陶玉恒; 乔丽红

    2016-01-01

    MATLAB guide is specialized in the graphical user interface environment for rapid development, using optional control of the guide tool to design a friendly interface, then in the corresponding button callback function in programming, designed to generate a typical digital signal. Then we deal with it, and the results show that the "digital signal processing" teaching in a number of important content of the demonstration system design. The designed system can log on and enter the main interface of the system, and then enter the corresponding sub module. The sub module totals seven blocks, were used to develop the design of discrete time signal, the design of discrete time system, the design of discrete linear convolution, the design of discrete Fourier transform, the design of discrete time signal in the Fourier transform, the design of system frequency response, the design of the FIR digital iflter and the design of IIR digital iflter. Among them, we focus on the design of discrete convolution and iflter design and presentation system. This system is helpful to the classroom teaching and can be able to give students intuitive feelings. Even people who not understand the MATLAB language programming can also master and understand it easily, and enjoy the dynamic sense of the picture, which can improve their learning interest in this area.%MATLAB中的Guide是专用于图形用户界面的快速开发环境,利用该Guide工具可以辅助数字信号课程教学。文章设计了基于GUI的数字信号处理课程演示系统,该系统可以登录界面,共有7块,分别开发了离散时间信号设计、离散时间系统设计、离散线性卷积设计、离散傅里叶变换设计、离散时间信号的傅里叶变换、系统频率响应设计,FIR数字滤波器的设计和IIR数字滤波器的设计。其中我们重点设计了离散卷积和滤波器设计演示系统。此系统可以辅助课堂教学,即便不懂MATLAB语言编程的人也

  20. Designing divertor targets for uniform power load

    Science.gov (United States)

    Dekeyser, W.; Reiter, D.; Baelmans, M.

    2015-08-01

    Divertor design for next step fusion reactors heavily relies on 2D edge plasma modeling with codes as e.g. B2-EIRENE. While these codes are typically used in a design-by-analysis approach, in previous work we have shown that divertor design can alternatively be posed as a mathematical optimization problem, and solved very efficiently using adjoint methods adapted from computational aerodynamics. This approach has been applied successfully to divertor target shape design for more uniform power load. In this paper, the concept is further extended to include all contributions to the target power load, with particular focus on radiation. In a simplified test problem, we show the potential benefits of fully including the radiation load in the design cycle as compared to only assessing this load in a post-processing step.

  1. Uniform guidelines improve client care.

    Science.gov (United States)

    Barnett, B

    1994-12-01

    Uniform national guidelines on the delivery of family planning methods and services improve client care, assuming these guidelines are based on current scientific information. Compliance with these guidelines yields safe and efficient delivery of family planning services. Service providers need information, training, supplies, and guidelines to deliver quality services. Guidelines contribute to consistency among family planning programs in different settings. Even though clinics may not provide the same services, the guidelines allow them to provide the same standards of care. Specifically, eligibility criteria, contraindications, and follow-up schedules are the same regardless of the service delivery point. Various international health organizations (such as World Health Organization, USAID, Program for International Training in Health, International Planned Parenthood Federation, and Association for Voluntary Surgical Contraception) have developed guidelines for family planning service delivery. Governments can use these documents to develop national family planning guidelines and policies. They should adapt the guidelines to local needs and consider program resources. After development of the national guidelines, training, workshops, and dissemination of written materials should be provided for policymakers, physicians, nurses, and other health providers. Countries that have either developed or are working to draft their own national guidelines are Cameroon, Ghana, Mexico, and Nepal.

  2. Discovery of Uniformly Expanding Universe

    Directory of Open Access Journals (Sweden)

    Cahill R. T.

    2012-01-01

    Full Text Available Saul Perlmutter and the Brian Schmidt – Adam Riess teams reported that their Friedmann-model GR-based analysis of their supernovae magnitude-redshift data re- vealed a new phenomenon of “dark energy” which, it is claimed, forms 73% of the energy / matter density of the present-epoch universe, and which is linked to the further claim of an accelerating expansion of the universe. In 2011 Perlmutter, Schmidt and Riess received the Nobel Prize in Physics “for the discovery of the accelerating ex- pansion of the Universe through observations of distant supernovae”. Here it is shown that (i a generic model-independent analysis of this data reveals a uniformly expanding universe, (ii their analysis actually used Newtonian gravity, and finally (iii the data, as well as the CMB fluctuation data, does not require “dark energy” nor “dark matter”, but instead reveals the phenomenon of a dynamical space, which is absent from the Friedmann model.

  3. Demonstration of the potential for energy conservation in two Midwestern pork processing plants. Final report, December 15, 1977-December 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, P.; Okos, M.

    1981-01-19

    Two Midwestern pork processing plants were studied to quantify present energy consumption and to determine potential energy savings with modification of existing processing equipment or adoption of alternative equipment. Process energy consumption was measured in each plant at each processing step or at each unit operation and pertinent costs obtained. Energy utilized was categorized by type such as gas, electricity, steam, etc. Process conditions such as temperature, pressure, flow rates, etc., were also measured so that they could be related to energy consumption. Through measurement of operating parameters and the calculation of material and energy balances, patterns of energy loss in the major unit operations were determined. The total yearly steam and gas energy consumed by the processes studied in Plant A amounted to 133.6 billion Btu's and 207.8 billion Btu's in Plant B. Of that total, Plant A uses approximately 15.5% and Plant B uses 7.5% for sanitation and cleaning. The remaining energy is used to operate the various unit operations. The energy used in the major unit operations can be broken down into lost energy and recoverable energy. Lost energy is that energy that will not effect production if eliminated. For the processes studied in Plant A, non-productive energy amounts to 48% of the energy supplied. The nonproductive energy in Plant B amounted to 60.6% of the total process energy. On the other hand, recoverable energy is that energy that was used for some productive purpose but still has value upon completion of the process. For the processes studied in Plant A, a recoverable energy amounts to 40% of the energy supplied. The potentially recoverable energy for Plant B is 35.8% of the process energy supplied.

  4. Repair or Violation Detection? Pre-Attentive Processing Strategies of Phonotactic Illegality Demonstrated on the Constraint of g-Deletion in German

    Science.gov (United States)

    Steinberg, Johanna; Jacobsen, Thomas Konstantin; Jacobsen, Thomas

    2016-01-01

    Purpose: Effects of categorical phonotactic knowledge on pre-attentive speech processing were investigated by presenting illegal speech input that violated a phonotactic constraint in German called "g-deletion." The present study aimed to extend previous findings of automatic processing of phonotactic violations and to investigate the…

  5. Demonstrating marketing accountability.

    Science.gov (United States)

    Gombeski, William R; Britt, Jason; Taylor, Jan; Riggs, Karen; Wray, Tanya; Adkins, Wanda; Springate, Suzanne

    2008-01-01

    Pressure on health care marketers to demonstrate effectiveness of their strategies and show their contribution to organizational goals is growing. A seven-tiered model based on the concepts of structure (having the right people, systems), process (doing the right things in the right way), and outcomes (results) is discussed. Examples of measures for each tier are provided and the benefits of using the model as a tool for measuring, organizing, tracking, and communicating appropriate information are provided. The model also provides a framework for helping management understand marketing's value and can serve as a vehicle for demonstrating marketing accountability.

  6. Scale-up of counter-current chromatography: demonstration of predictable isocratic and quasi-continuous operating modes from the test tube to pilot/process scale.

    Science.gov (United States)

    Sutherland, Ian; Hewitson, Peter; Ignatova, Svetlana

    2009-12-11

    Predictable scale-up from test tube derived distribution ratios and analytical-scale sample loading optimisation is demonstrated using a model sample system of benzyl alcohol and p-cresol in a heptane:ethyl acetate:methanol:water phase system with the new 18 L Maxi counter-current chromatography centrifuge. The versatility of having a liquid stationary phase with its high loading capacity and flexible operating modes is demonstrated at two different scales by separating and concentrating target compounds using a mixture of caffeine, vanillin, naringenin and carvone using a quasi-continuous technique called intermittent counter-current extraction.

  7. The symbolism and myth surrounding nurses' uniform.

    Science.gov (United States)

    Richardson, M

    This article addresses nurses' uniform from the perspective of the symbolic, myth, legend and competing discourse. The analysis touches upon why nurses working with people who have learning disabilities discarded the nurses' uniform and why other nurses may consider doing so, particularly if suitable alternatives exist. The analysis draws from various areas of nursing practice, including the nursing of disabled people, elderly people and people with learning disabilities. Nurses' uniform is revealed as a totem of considerable potency such that to wear a uniform in just any setting or context has to be cautioned. The practicalities of protective clothing are addressed. A differentiation is drawn between uniform and protective clothing such that much of the undesirable symbolism associated with uniform may be discarded with a consequent enhancement of the image of the nurse.

  8. A novel lithography technique for formation of large areas of uniform nanostructures

    Science.gov (United States)

    Wu, Wei; Dey, Dibyendu; Memis, Omer G.; Katsnelson, Alex; Mohseni, Hooman

    2008-08-01

    With nanotechnology becoming widely used, many applications such as plasmonics, sensors, storage devices, solar cells, nano-filtration and artificial kidneys require the structures with large areas of uniform periodic nanopatterns. Most of the current nano-manufacturing techniques, including photolithography, electron-beam lithography, and focal ion beam milling, are either slow or expensive to be applied into the areas. Here, we demonstrate an alternative and novel lithography technique - Nanosphere Photolithography (NSP) - that generates a large area of highly uniform periodic nanoholes or nanoposts by utilizing the monolayer of hexagonally close packed (HCP) silica microspheres as super-lenses on top of photoresist. The size of the nanopatterns generated is almost independent of the sphere sizes and hence extremely uniform patterns can be obtained. We demonstrate that the method can produce hexagonally packed arrays of hole of sub-250 nm size in positive photoresist using a conventional exposure system with a broadband UV source centered at 400 nm. We also show a large area of highly uniform gold nanoholes (~180 nm) and nanoposts (~300nm) array with the period of 1 μm fabricated by the combination of lift-off and NSP. The process is not limited to gold. Similar structures have been shown with aluminum and silicon dioxide layer. The period and size of the structures can also be tuned by changing proper parameters. The technique applying self-assembled and focusing properties of micro-/nano-spheres into photolithography establishes a new paradigm for mask-less photolithography technique, allowing rapid and economical creation of large areas of periodic nanostructures with a high throughput.

  9. School uniforms: tradition, benefit or predicament?

    OpenAIRE

    Van Aardt, Annette Marie; Wilken, Ilani

    2012-01-01

    This article focuses on the controversies surrounding school uniforms. Roleplayers in this debate in South Africa are parents, learners and educators, and arguments centre on aspects such as identity, economy and the equalising effect of school uniforms, which are considered in the literature to be benefits. Opposing viewpoints highlight the fact that compulsory uniforms infringe on learners’ constitutional rights to self-expression. The aim of this research was to determine the perspectives ...

  10. Learning From Demonstration?

    DEFF Research Database (Denmark)

    Koch, Christian; Bertelsen, Niels Haldor

    2014-01-01

    , and micro combined heat and power using hydrogen. Using sociological and business economic theories of innovation, the paper discusses how early movers of innovation tend to obtain only partial success when demonstrating their products and often feel obstructed by minor details. The empirical work...... encompasses both an evaluation of the design and Construction process as well as a post-occupancy evaluation. Process experiences include the use of a multidisciplinary competence group and performance measurement. The commencement of the project was enthusiastic, but it was forced into more traditional forms...

  11. Collaborative Filtering in a Non-Uniform World: Learning with the Weighted Trace Norm

    CERN Document Server

    Salakhutdinov, Ruslan

    2010-01-01

    We show that matrix completion with trace-norm regularization can be significantly hurt when entries of the matrix are sampled non-uniformly. We introduce a weighted version of the trace-norm regularizer that works well also with non-uniform sampling. Our experimental results demonstrate that the weighted trace-norm regularization indeed yields significant gains on the (highly non-uniformly sampled) Netflix dataset.

  12. On the Compactly Locally Uniformly Rotund Points of Orlicz Spaces

    Indian Academy of Sciences (India)

    Lili Chen; Yunan Cui

    2007-11-01

    In this paper, locally uniformly rotund points and compactly locally uniformly rotund points are introduced. Moreover, criteria for compactly locally uniformly rotund points in Orlicz spaces are given.

  13. Transistor bonding pad configuration for uniform injection and low inductance

    Science.gov (United States)

    Jacobson, D. S.

    1970-01-01

    Modification of process for fabricating transistors, which comprises a metallization-pattern design for emitter and base areas together with a double bonding configuration for each emitter and base-bonding lead, improves uniformity of carrier injection in transistors and of reducing lead inductances at base-emitter terminals.

  14. Solar renovation demonstration projects

    Energy Technology Data Exchange (ETDEWEB)

    Bruun Joergensen, O. [ed.

    1998-10-01

    In the framework of the IEA SHC Programme, a Task on building renovation was initiated, `Task 20, Solar Energy in Building Renovation`. In a part of the task, Subtask C `Design of Solar Renovation Projects`, different solar renovation demonstration projects were developed. The objective of Subtask C was to demonstrate the application of advanced solar renovation concepts on real buildings. This report documents 16 different solar renovation demonstration projects including the design processes of the projects. The projects include the renovation of houses, schools, laboratories, and factories. Several solar techniques were used: building integrated solar collectors, glazed balconies, ventilated solar walls, transparent insulation, second skin facades, daylight elements and photovoltaic systems. These techniques are used in several simple as well as more complex system designs. (au)

  15. Extending maps between pre-uniform spaces

    OpenAIRE

    Adalberto García-Máynez; Rubén Mancio-Toledo

    2012-01-01

    [EN] We give sufficient conditions on a uniformly continuous map f: (X,U) → (Y, V ) between completable T1-pre-uniform spaces (X,U), (Y, V ) to have a continuous or a uniformly continuous extension f:X → Y between the corresponding completions. García-Máynez, A.; Mancio-Toledo, R. (2012). Extending maps between pre-uniform spaces. Applied General Topology. 13(1):21-25. doi:10.4995/agt.2012.1634. 21 25 13 1

  16. Concentration uniformity of extemporaneously prepared ranitidine suspension.

    Science.gov (United States)

    Karnes, H T; Harris, S R; Garnett, W R; March, C

    1989-02-01

    The concentration uniformity of an extemporaneously prepared ranitidine suspension was studied. To prepare the ranitidine suspension, 36 150-mg tablets were pulverized and suspended in 180 mL of distilled water. This mixture was diluted with simple syrup to a total volume of 360 mL, resulting in a final ranitidine concentration of 150 mg/10 mL. Samples from each of three bottles that had been filled with 60 mL of the suspension were assayed for ranitidine content by high-performance liquid chromatography. The sedimentation of suspended ranitidine tablet particles was studied by visual observation of the setting process in 10-mL samples from the same batch. The overall mean concentrations (in milligrams per milliliter) of ranitidine were 14.53, 15.25, 13.92, 12.67, and 12.72 at 0, 3, 7, 14, and 21 days, respectively. Compared with baseline, the difference in the ranitidine concentration was not significant over days 0-7. The ranitidine concentration was significantly reduced during the following time intervals: days 0-14, days 0-21, and days 7-21. In the settling experiments, the mean time (+/- S.D.) for sediment to first appear on the test tube bottom was 14.67 +/- 5.35 seconds. Approximately 40-50% (mean level = 3.2 mm) of the total sedimentation level (mean level = 7.3 mm) was observed one minute after shaking. The uniformity of ranitidine suspensions compounded according to procedures described in this report possibly could be improved with sonication. The ranitidine suspension should be well shaken, the dosage should be measured immediately after shaking, and the suspension should be used within seven days of compounding.

  17. Uniform: an evidence review of the microbiological significance of uniforms and uniform policy in the prevention and control of healthcare-associated infections. Report to the Department of Health (England).

    Science.gov (United States)

    Wilson, J A; Loveday, H P; Hoffman, P N; Pratt, R J

    2007-08-01

    A systematic search and quality assessment of published literature was conducted to establish current knowledge on the role of healthcare workers uniforms' as vehicles for the transfer of healthcare-associated infections. This review comprised a systematic search of national and international guidance, published literature and data on recent advances in laundry technology and processes. We found only a small number of relevant studies that provided limited evidence directly related to the decontamination of uniforms. Studies concerning domestic laundry processes are small scale and largely observational. Current practice and guidance for laundering uniforms is extrapolated from studies of industrial hospital linen processing. Healthcare workers' uniforms, including white coats, become progressively contaminated in use with bacteria of low pathogenicity from the wearer and of mixed pathogenicity from the clinical environment and patients. The hypothesis that uniforms/clothing could be a vehicle for the transmission of infections is not supported by existing evidence. All components of the laundering process contribute to the removal or killing of micro-organisms on fabric. There is no robust evidence of a difference in efficacy of decontamination of uniforms/clothing between industrial and domestic laundry processes, or that the home laundering of uniforms provides inadequate decontamination.

  18. Textile drying using solarized can dryers to demonstrate the application of solar energy to industrial drying or dehydration processes, Phase II. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, P.D.; Beesing, M.E.; Bessler, G.L.

    1979-12-01

    This program has resulted in the installation of a solar energy collection system for providing process heat to a textile drying process. The solar collection subsystem uses 700 square meters (7500 square feet) of parabolic trough, single-axis tracking, concentrating collectors to heat water in a high temperature water (HTW) loop. The solar collectors nominally generate 193/sup 0/C (380/sup 0/F) water with the HTW loop at 1.9 x 10/sup 6/ Pa (275 psi). A steam generator is fueled with the HTW and produces 450 kg/hour (1000 pounds per hour) of process steam at the nominal design point conditions. The solar-generated process steam is at 0.5 x 10/sup 6/ Pa (75 psi) and 160/sup 0/C (321/sup 0/F). It is predicted that the solar energy system will provide 1.2 x 10/sup 6/ MJ/year (1.1 x 10/sup 9/ Btu/year) to the process. This is 46 percent of the direct isolation available to the collector field during the operational hours (300 days/year of the Fairfax mill. The process being solarized is textile drying using can dryers. The can dryers are part of a slashing operation in a WestPoint Pepperell mill in Fairfax, Alabama. Over 50 percent of all woven goods are processed through slashers and dried on can dryers. The collectors were fabricated by Honeywell at a pilot production facility in Minneapolis, Minnesota, under a 3000-square-meter (32,000-square-foot) production run. The collectors and other system components were installed at the site by the Bahnson Service Company and their subcontractors, acting as the project general contractor. System checkout and start-up was conducted. Preliminary system performance was determined from data collected during start-up. System design, fabrication and installation, data analysis, operation and maintenance procedures, and specifications and drawings are presented.

  19. Development of a CMPO based extraction process for partitioning of minor actinides and demonstration with genuine fast reactor fuel solution (155 GWd/Te)

    Energy Technology Data Exchange (ETDEWEB)

    Antony, M.P.; Kumaresan, R.; Suneesh, A.S. [Indira Gandhi Centre for Atomic Research, Kalpakkam (IN). Fuel Chemistry Div.] (and others)

    2011-07-01

    A method has been developed for partitioning of minor actinides from fast reactor (FR) fuel solution by a TRUEX solvent composed of 0.2 M n-octyl(phenyl)-N,N-diisobutylcarbamoyl-methylphosphine oxide (CMPO)-1.2 M tri-n-butylphosphate (TBP) in n-dodecane (n-DD), and subsequently demonstrated with genuine fast reactor dissolver solution (155 GWd/Te) using a novel 16-stage ejector mixer settler in hot cells. Cesium, plutonium and uranium present in the dissolver solution were removed, prior to minor actinide partitioning, by using ammonium molybdophosphate impregnated XAD-7 (AMP-XAD), methylated poly(4-vinylpyridine) (PVP-Me), and macroporous bifunctional phosphinic acid (MPBPA) resins respectively. Extraction of europium(III) and cerium(III) from simulated and real dissolver solution, and their stripping behavior from loaded organic phase was studied in batch method using various citric acid-nitric acid formulations. Based on these results, partitioning of minor actinides from fast reactor dissolver solution was demonstrated in hot cells. The extraction and stripping profiles of {sup 154}Eu, {sup 144}Ce, {sup 106}Ru and {sup 137}Cs, and mass balance of {sup 241}Am(III) achieved in the demonstration run have been reported in this paper. (orig.)

  20. Enhanced Deposition Uniformity via an Auxiliary Electrode in Massive Electrospinning.

    Science.gov (United States)

    Wu, Dezhi; Xiao, Zhiming; Deng, Lei; Sun, Yu; Tan, Qiulin; Dong, Linxi; Huang, Shaohua; Zhu, Rui; Liu, Yifang; Zheng, Wanxi; Zhao, Yang; Wang, Lingyun; Sun, Daoheng

    2016-07-22

    Uniform deposition of nanofibers in the massive electrospinning process is critical in the industrial applications of nanofibers. Tip-Induced Electrospinning (TIE) is a cost-effective large-scale nanofiber-manufacturing method, but it has poor deposition uniformity. An auxiliary conductive electrode connected to the emitting electrode was introduced to improve the deposition uniformity of the nanofibers. The effects of the auxiliary electrode shape, the tilted angles and the position of the boat-like electrode on the electric field distribution, the diameter of the nanofibers, the jet control and the deposition uniformity were explored by using finite element analysis of the electric field and experiments. Experiments showed that the boat-like electrode at 20 mm above the reservoir bottom with a 5° tilted angle helped to decrease the relative deposition error of nanofibers in the greatest extent to about 5.66%, indicating such an auxiliary electrode is a good candidate method to greatly improve the deposition uniformity of nanofibers in massive electrospinning.

  1. Uniform grid upsampling of 3D lidar point cloud data

    Science.gov (United States)

    Gurram, Prudhvi; Hu, Shuowen; Chan, Alex

    2013-03-01

    Airborne laser scanning light detection and ranging (LiDAR) systems are used for remote sensing topology and bathymetry. The most common data collection technique used in LiDAR systems employs a linear mode scanning. The resulting scanning data form a non-uniformly sampled 3D point cloud. To interpret and further process the 3D point cloud data, these raw data are usually converted to digital elevation models (DEMs). In order to obtain DEMs in a uniform and upsampled raster format, the elevation information from the available non-uniform 3D point cloud data are mapped onto the uniform grid points. After the mapping is done, the grid points with missing elevation information are lled by using interpolation techniques. In this paper, partial di erential equations (PDE) based approach is proposed to perform the interpolation and to upsample the 3D point cloud onto a uniform grid. Due to the desirable e ects of using higher order PDEs, smoothness is maintained over homogeneous regions, while sharp edge information in the scene well preserved. The proposed algorithm reduces the draping e ects near the edges of distinctive objects in the scene. Such annoying draping e ects are commonly associated with existing point cloud rendering algorithms. Simulation results are presented in this paper to illustrate the advantages of the proposed algorithm.

  2. An Implementation of the REpresentation and MAintenance of Process Knowledge(REMAP) Model in the Knowledge-Based Software Assistant Concept Demonstration System

    Science.gov (United States)

    1993-09-01

    D.M. Elefante , p. 8, 1988. 8. Debellis, M., "The Concept Demonstration Rapid Prototype System", PROCEEDINGS OF THE FIFTH CONFERENCE ON KBSA, p. 222...1987. 11. Elefante , loc. cit., p. 8. 12. White, op. cit., p. 3. 13. White, op. cit., p. 4. 14. Goldberg, A., et al., "KBSA Performance Estimation...Assistant Program Specification," Documentation, RADC Contract F30602-86-C-0026. 71 15. White, op.cit., p. 5. 16. White, op. cit., pp. 3-4. 17. Elefante , op

  3. Demonstration of GTS Duratek Process for Stabilizing Mercury Contaminated (<260 ppm) Mixed Wastes. Mixed Waste Focus Area. OST Reference No. 2409

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    1999-09-01

    Mercury-contaminated wastes in many forms are present at various U. S. Department of Energy (DOE) sites. At least 26 different DOE sites have this type of mixed low-level waste in their storage facilities, totaling approximately 6,000 m3. Mercury contamination in the wastes at DOE sites presents a challenge because it exists in various forms, such as soil, sludges, and debris, as well as in different chemical species of mercury. Stabilization is of interest for radioactively contaminated mercury waste (<260 ppm Hg) because of its success with particular wastes, such as soils, and its promise of applicability to a broad range of wastes. However, stabilization methods must be proven to be adequate to meet treatment standards. They must also be proven feasible in terms of economics, operability, and safety. This report summarizes the findings from a stabilization technology demonstration conducted by GTS Duratek, Inc. Phase I of the study involved receipt and repackaging of the material, followed by preparations for waste tracking. Phase II examined the bench-scale performance of grouting at two different loadings of waste to grouted mass. Phase III demonstrated in-drum mixing and solidification using repackaged drums of sludge. Phase IV initially intended to ship final residues to Envirocare for disposal. The key results of the demonstration are as follows: (1) Solidification tests were performed at low and high waste loading, resulting in stabilization of mercury to meet the Universal Treatment Standard of 0.025 mg/L at the low loading and for two of the three runs at the high loading. The third high-loading run had a Toxicity Characteristic Leaching Procedure (TCLP) of 0.0314 mg/L. (2) Full-drum stabilization using the low loading formula was demonstrated. (3) Organic compound levels were discovered to be higher than originally reported, including the presence of some pesticides. Levels of some radionuclides were much higher than initially reported. (4

  4. Quantitative proteome analysis of Streptomyces coelicolor Nonsporulating liquid cultures demonstrates a complex differentiation process comparable to that occurring in sporulating solid cultures

    DEFF Research Database (Denmark)

    Manteca, Angel; Jung, Hye R; Schwämmle, Veit

    2010-01-01

    Streptomyces species produce many clinically important secondary metabolites and present a complex developmental cycle that includes programmed cell death (PCD) phenomena and sporulation. Industrial fermentations are usually performed in liquid cultures, conditions in which Streptomyces strains...... of the different developmental stages in liquid and solid S. coelicolor cultures, in order to give new insights in Streptomyces biology, and improve industrial fermentations. Using iTRAQ labeling and LC-MS/MS analysis of peptides, we demonstrate that differentiation in S. coelicolor liquid cultures is comparable...

  5. Uniform and Non-Uniform Optimum Scalar Quantizers Performances: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Fendy Santoso

    2008-05-01

    Full Text Available The aim of this research is to investigate source coding, the representation of information source output by finite R bits/symbol. The performance of optimum quantisers subject to an entropy constraint has been studied. The definitive work in this area is best summarised by Shannon’s source coding theorem, that is, a source with entropy H can be encoded with arbitrarily small error probability at any rate R (bits/source output as long as R>H. Conversely, If R the error probability will be driven away from zero, independent of the complexity of the encoder and the decoder employed. In this context, the main objective of engineers is however to design the optimum code. Unfortunately, the rate-distortion theorem does not provide the recipe for such a design. The theorem does, however, provide the theoretical limit so that we know how close we are to the optimum. The full understanding of the theorem also helps in setting the direction to achieve such an optimum. In this research, we have investigated the performances of two practical scalar quantisers, i.e., a Lloyd-Max quantiser and the uniformly defined one and also a well-known entropy coding scheme, i.e., Huffman coding against their theoretically attainable optimum performance due to Shannon’s limit R. It has been shown that our uniformly defined quantiser could demonstrate superior performance. The performance improvements, in fact, are more noticeable at higher bit rates.

  6. A Uniform Syntax and Discourse Structure

    DEFF Research Database (Denmark)

    Hardt, Daniel

    2013-01-01

    I present arguments in favor of the Uniformity Hypothesis: the hypothesis that discourse can extend syntax dependencies without conflicting with them. I consider arguments that Uniformity is violated in certain cases involving quotation, and I argue that the cases presented in the literature...

  7. School Uniform Policies in Public Schools

    Science.gov (United States)

    Brunsma, David L.

    2006-01-01

    The movement for school uniforms in public schools continues to grow despite the author's research indicating little if any impact on student behavior, achievement, and self-esteem. The author examines the distribution of uniform policies by region and demographics, the impact of these policies on perceptions of school climate and safety, and…

  8. Student Dress Codes and Uniforms. Research Brief

    Science.gov (United States)

    Johnston, Howard

    2009-01-01

    According to an Education Commission of the States "Policy Report", research on the effects of dress code and school uniform policies is inconclusive and mixed. Some researchers find positive effects; others claim no effects or only perceived effects. While no state has legislatively mandated the wearing of school uniforms, 28 states and…

  9. School Uniforms and Discourses on Childhood.

    Science.gov (United States)

    Bodine, Ann

    2003-01-01

    This ethnographic study examined the introduction of school uniforms in the public schools of one California city. Findings indicated that the uniform issue intersected with issues such as student safety and violence, family stress, egalitarianism, competitive dressing, and a power struggle over shaping the childhood environment. It was concluded…

  10. School Uniform Policies: Students' Views of Effectiveness.

    Science.gov (United States)

    McCarthy, Teresa M.; Moreno, Josephine

    2001-01-01

    Focus-group interviews of New York City middle-school students about their perceptions of the effectiveness of the school-uniform policy. Finds that students' perceptions of the effects of school-uniform policy on school culture varied considerably with those intended by the principal. (Contains 40 references.) (PKP)

  11. A School Uniform Program That Works.

    Science.gov (United States)

    Loesch, Paul C.

    1995-01-01

    According to advocates, school uniforms reduce gang influence, decrease families' clothing expenditures, and help mitigate potentially divisive cultural and economic differences. Aiming to improve school climate, a California elementary school adopted uniforms as a source of pride and affiliation. This article describes the development of the…

  12. On Uniform Convexity of Banach Spaces

    Institute of Scientific and Technical Information of China (English)

    Qing Jin CHENG; Bo WANG; Cui Ling WANG

    2011-01-01

    This paper gives some relations and properties of several kinds of generalized convexity in Banach spaces. As a result, it proves that every kind of uniform convexity implies the Banach-Sakes property, and several notions of uniform convexity in literature are actually equivalent.

  13. Uniformly convex-transitive function spaces

    OpenAIRE

    Rambla-Barreno, Fernando; Talponen, Jarno

    2009-01-01

    We introduce a property of Banach spaces called uniform convex-transitivity, which falls between almost transitivity and convex-transitivity. We will provide examples of uniformly convex-transitive spaces. This property behaves nicely in connection with some Banach-valued function spaces. As a consequence, we obtain new examples of convex-transitive Banach spaces.

  14. School Dress Codes and Uniform Policies.

    Science.gov (United States)

    Anderson, Wendell

    2002-01-01

    Opinions abound on what students should wear to class. Some see student dress as a safety issue; others see it as a student-rights issue. The issue of dress codes and uniform policies has been tackled in the classroom, the boardroom, and the courtroom. This Policy Report examines the whole fabric of the debate on dress codes and uniform policies…

  15. A biological/chemical process for reduced waste and energy consumption, Caprolactam production: Phase 1, Select microorganisms and demonstrate feasibility. Final report

    Energy Technology Data Exchange (ETDEWEB)

    St.Martin, E.J.

    1995-08-01

    A novel biological/chemical process for converting cyclohexane into caprolactam was investigated. Microorganisms in a bioreactor would be used to convert cyclohexane into caprolactone followed by chemical synthesis of caprolactam using ammonia. The proposed bioprocess would be more energy efficient and reduce byproducts and wastes that are generated by the current chemical process. We have been successful in isolating from natural soil and water samples two microorganisms that can utilize cyclohexane as a sole source of carbon and energy for growth. These microorganisms were shown to have the correct metabolic intermediates and enzymes to convert cyclohexane into cyclohexanol, cyclohexanone and caprolactone. Genetic techniques to create and select for caprolactone hydrolase negative-mutants are being developed. These blocked-mutants will be used to convert cyclohexane into caprolactone but, because of the block, be unable to metabolize the caprolactone further and excrete it as a final end product.

  16. Analysis of weld seam uniformity through temperature distribution by spatially resolved detector elements in the wavelength range of 0.3μm to 5μm for the detection of structural changing heating and cooling processes

    Science.gov (United States)

    Lempe, B.; Maschke, R.; Rudek, F.; Baselt, T.; Hartmann, P.

    2016-03-01

    Online process control systems often only detecting temperatures at a local area of the machining point and determining an integrated value. In order to determine the proper welding quality and the absence of defects, such as temperature induced stress cracks, it is necessary to do time and space resolved measurements before, during and after the production process. The system under development consists of a beam splitting unit which divides the electromagnetic radiation of the heated component on two different sensor types. For high temperatures, a sensor is used which is sensitive in the visible spectrum and has a dynamic range of 120dB.1 Thus, very high intensity differences can be displayed and a direct analysis of the temperature profile of the weld spots is possible.2 A second sensor is operating in the wavelength range from 1 micron to 5 microns and allows the determination of temperatures from approximately 200°C.3 At the beginning of a welding process, the heat-up phase of the metal is critical to the resultant weld quality. If a defined temperature range exceeded too fast, the risk of cracking is significantly increased.4 During the welding process the thermal supervision of the central processing location is decisive for a high secure weld. In the border areas as well as in connection of the welding process especially cooling processes are crucial for the homogeneity of the results. In order to obtain sufficiently accurate resolution of the dynamic heating- and cooling-processes, the system can carry out up to 500 frames per second.

  17. Characterization of new class III lantibiotics--erythreapeptin, avermipeptin and griseopeptin from Saccharopolyspora erythraea, Streptomyces avermitilis and Streptomyces griseus demonstrates stepwise N-terminal leader processing.

    Science.gov (United States)

    Völler, Ginka H; Krawczyk, Joanna M; Pesic, Alexander; Krawczyk, Bartlomiej; Nachtigall, Jonny; Süssmuth, Roderich D

    2012-05-29

    Lantibiotics are a large group of ribosomally synthesized peptides post-translationally modified to incorporate the amino acid lanthionine. They are classified, according to their biosynthetic pathway and bioactivity, into three major subtypes. Of Actinomycetes type III lantibiotics, only four peptides (SapB, SapT, LabA1, and LabA2) have been described and structurally characterized, although homologous gene clusters are abundant in other Actinomycetes. All these gene clusters share a similar architecture with a characteristic Ser/Ser/Cys motif in precursor peptides, which has previously been suggested to act as a precursor for lanthionine (SapB) and labionin (LabA2) rings. Mass spectrometry screening led to the discovery and characterization of three new representatives of type III lantibiotics: Avermipeptin (Avi), Erythreapeptin (Ery), and Griseopeptin (Gri) from Streptomyces avermitilis DSM 46492, Saccharopolyspora erythraea NRRL 2338, and Streptomyces griseus DSM 40236, respectively. Apart from the assignment of these peptides to their corresponding gene clusters, additional investigations on Avi, Ery and Gri peptides indicate stepwise leader processing by putative aminopeptidase-like protease(s), thus yielding mixtures of differently N-terminal-processed lantibiotic peptides. Similar peptide processing was observed for a heterologously expressed eryth biosynthetic gene cluster expressed in a Streptomyces host system. Remarkably, all isolates of the new type III lantibiotics contain both the amino acids lanthionine and labionin, thus implying dual-mode cyclase activity of the processing lyase-kinase-cyclase enzymes. These findings have implications for the structures and maturation of other type III lantibiotics from Actinomycetes.

  18. Some results on uniform arithmetic circuit complexity

    DEFF Research Database (Denmark)

    Frandsen, Gudmund Skovbjerg; Valence, Mark; Barrington, David A. Mix

    1994-01-01

    We introduce a natural set of arithmetic expressions and define the complexity class AE to consist of all those arithmetic functions (over the fieldsF 2n) that are described by these expressions. We show that AE coincides with the class of functions that are computable with constant depth...... that if some such representation is X-uniform (where X is P or DLOGTIME), then the arithmetic complexity of a function (measured with X-uniform unbounded fan-in arithmetic circuits) is identical to the Boolean complexity of this function (measured with X-uniform threshold circuits). We show the existence...... and polynomial-size unbounded fan-in arithmetic circuits satisfying a natural uniformity constraint (DLOGTIME-uniformity). A 1-input and 1-output arithmetic function over the fieldsF2n may be identified with ann-input andn-output Boolean function when field elements are represented as bit strings. We prove...

  19. Uniform Determinstic Discrete Method for Radiative Viewfactors in Complex Geometric Systems

    Institute of Scientific and Technical Information of China (English)

    1995-01-01

    Based on the analysis of uniform sampling theorem,this paper presented the uniform deterministic discrete method(UDDM) for computing the diffuse radiation viewfactors in complex geometrical sys-tems.The accuracy,speed and convergence are discussed or compared with that of Monte Carlo Method(MCM) in order to demonstrate the advantages of UDDM.

  20. Nanosecond laser texturing of uniformly and non-uniformly wettable micro structured metal surfaces for enhanced boiling heat transfer

    Science.gov (United States)

    Zupančič, Matevž; Može, Matic; Gregorčič, Peter; Golobič, Iztok

    2017-03-01

    Microstructured uniformly and non-uniformly wettable surfaces were created on 25-μm-thin stainless steel foils by laser texturing using a marking nanosecond Nd:YAG laser (λ = 1064 nm) and utilizing various laser fluences and scan line separations. High-speed photography and high-speed IR thermography were used to investigate nucleate boiling heat transfer on the microstructured surfaces. The most pronounced results were obtained on a surface with non-uniform microstructure and non-uniform wettability. The obtained results show up to a 110% higher heat transfer coefficients and 20-40 times higher nucleation site densities compared to the untextured surface. We show that the number of active nucleation sites is significantly increased in the vicinity of microcavities that appeared in areas with the smallest (10 μm) scan line separation. Furthermore, this confirms the predictions of nucleation criteria and proves that straightforward, cost-effective nanosecond laser texturing allows the production of cavities with diameters of up to a few micrometers and surfaces with non-uniform wettability. Additionally, this opens up important possibilities for a more deterministic control over the complex boiling process.

  1. Nucla CFB Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-01

    This report documents Colorado-Ute Electric Association's Nucla Circulating Atmospheric Fluidized-Bed Combustion (AFBC) demonstration project. It describes the plant equipment and system design for the first US utility-size circulating AFBC boiler and its support systems. Included are equipment and system descriptions, design/background information and appendices with an equipment list and selected information plus process flow and instrumentation drawings. The purpose of this report is to share the information gathered during the Nucla circulating AFBC demonstration project and present it so that the general public can evaluate the technical feasibility and cost effectiveness of replacing pulverized or stoker-fired boiler units with circulating fluidized-bed boiler units. (VC)

  2. Mercury Contamination - Amalgamate (contract with NFS and ADA). Demonstration of DeHgSM Process. Mixed Waste Focus Area. OST Reference Number 1675

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    1999-09-01

    Through efforts led by the Mixed Waste Focus Area (MWFA) and its Mercury Working Group (HgWG), the inventory of bulk elemental mercury contaminated with radionuclides stored at various U.S. Department of Energy (DOE) sites is thought to be approximately 16 m3 (Conley et al. 1998). At least 19 different DOE sites have this type of mixed low-level waste in their storage facilities. The U.S. Environmental Protection Agency (EPA) specifies amalgamation as the treatment method for radioactively contaminated elemental mercury. Although the chemistry of amalgamation is well known, the practical engineering of a sizable amalgamation process has not been tested (Tyson 1993). To eliminate the existing DOE inventory in a reasonable timeframe, scalable equipment is needed that can produce waste forms that meet the EPA definition of amalgamation, produce waste forms that pass the EPA Toxicity Characteristic Leaching Procedure (TCLP) limit of 0.20 mg/L, limit mercury vapor concentrations during processing to below the Occupational Safety and Health Administration’s (OSHA) 8-h worker exposure limit (50 mg/m3) for mercury, and perform the above economically.

  3. Mercury Contamination - Amalgamate (contract with NFS and ADA). Demonstration of DeHgSM Process. Mixed Waste Focus Area. OST Reference Number 1675

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    1999-09-01

    Through efforts led by the Mixed Waste Focus Area (MWFA) and its Mercury Working Group (HgWG), the inventory of bulk elemental mercury contaminated with radionuclides stored at various U.S. Department of Energy (DOE) sites is thought to be approximately 16 m3 (Conley et al. 1998). At least 19 different DOE sites have this type of mixed low-level waste in their storage facilities. The U.S. Environmental Protection Agency (EPA) specifies amalgamation as the treatment method for radioactively contaminated elemental mercury. Although the chemistry of amalgamation is well known, the practical engineering of a sizable amalgamation process has not been tested (Tyson 1993). To eliminate the existing DOE inventory in a reasonable timeframe, scalable equipment is needed that can produce waste forms that meet the EPA definition of amalgamation, produce waste forms that pass the EPA Toxicity Characteristic Leaching Procedure (TCLP) limit of 0.20 mg/L, limit mercury vapor concentrations during processing to below the Occupational Safety and Health Administration’s (OSHA) 8-h worker exposure limit (50 mg/m3) for mercury, and perform the above economically.

  4. The role of reservoir characterization in the reservoir management process (as reflected in the Department of Energy`s reservoir management demonstration program)

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, M.L. [BDM-Petroleum Technologies, Bartlesville, OK (United States); Young, M.A.; Madden, M.P. [BDM-Oklahoma, Bartlesville, OK (United States)] [and others

    1997-08-01

    Optimum reservoir recovery and profitability result from guidance of reservoir practices provided by an effective reservoir management plan. Success in developing the best, most appropriate reservoir management plan requires knowledge and consideration of (1) the reservoir system including rocks, and rock-fluid interactions (i.e., a characterization of the reservoir) as well as wellbores and associated equipment and surface facilities; (2) the technologies available to describe, analyze, and exploit the reservoir; and (3) the business environment under which the plan will be developed and implemented. Reservoir characterization is the essential to gain needed knowledge of the reservoir for reservoir management plan building. Reservoir characterization efforts can be appropriately scaled by considering the reservoir management context under which the plan is being built. Reservoir management plans de-optimize with time as technology and the business environment change or as new reservoir information indicates the reservoir characterization models on which the current plan is based are inadequate. BDM-Oklahoma and the Department of Energy have implemented a program of reservoir management demonstrations to encourage operators with limited resources and experience to learn, implement, and disperse sound reservoir management techniques through cooperative research and development projects whose objectives are to develop reservoir management plans. In each of the three projects currently underway, careful attention to reservoir management context assures a reservoir characterization approach that is sufficient, but not in excess of what is necessary, to devise and implement an effective reservoir management plan.

  5. Pathways to commercial wind power in the US, Europe and Japan. The role of demonstration projects and field trials in the innovation process

    Energy Technology Data Exchange (ETDEWEB)

    Harborne, Paul; Hendry, Chris [Cass Business School, City University, 106 Bunhill Row, London EC1Y 8TZ (United Kingdom)

    2009-09-15

    A growing, but little understood area of Government involvement in promoting renewable energy, is the use of demonstration projects and field trials (DTs) as a policy tool. This paper explores the historical role of DTs in the commercialisation of wind turbines. We review information from government, academic and industry sources, together with the newly created Cass Wind DT database, and consider the context, objectives, participants and nature of wind DTs in the EU, US and Japan. Overall, it is difficult to identify the benefits of wind DTs for many of the key actors. Government funding of DTs does not appear to be shaped by coherent or targeted strategic objectives-indeed governments use DTs differently despite similar stated objectives. A common theme has been the involvement of many stakeholders, with local authorities, utilities and operators taking the lead rather than manufacturers. Wind DTs appear to have neither enabled participating manufacturers to become significant global suppliers-with a few exceptions driven by additional financial and legislative support from national governments-nor to have established a dominant design. The major benefit of wind DTs appears to have been 'learning by using' for utilities and wind farm operators, reducing operational costs. (author)

  6. Pathways to commercial wind power in the US, Europe and Japan: The role of demonstration projects and field trials in the innovation process

    Energy Technology Data Exchange (ETDEWEB)

    Harborne, Paul [Cass Business School, City University, 106 Bunhill Row, London EC1Y 8TZ (United Kingdom)], E-mail: p.harborne@city.ac.uk; Hendry, Chris [Cass Business School, City University, 106 Bunhill Row, London EC1Y 8TZ (United Kingdom)], E-mail: c.n.hendry@city.ac.uk

    2009-09-15

    A growing, but little understood area of Government involvement in promoting renewable energy, is the use of demonstration projects and field trials (DTs) as a policy tool. This paper explores the historical role of DTs in the commercialisation of wind turbines. We review information from government, academic and industry sources, together with the newly created Cass Wind DT database, and consider the context, objectives, participants and nature of wind DTs in the EU, US and Japan. Overall, it is difficult to identify the benefits of wind DTs for many of the key actors. Government funding of DTs does not appear to be shaped by coherent or targeted strategic objectives-indeed governments use DTs differently despite similar stated objectives. A common theme has been the involvement of many stakeholders, with local authorities, utilities and operators taking the lead rather than manufacturers. Wind DTs appear to have neither enabled participating manufacturers to become significant global suppliers-with a few exceptions driven by additional financial and legislative support from national governments-nor to have established a dominant design. The major benefit of wind DTs appears to have been 'learning by using' for utilities and wind farm operators, reducing operational costs.

  7. Developing Work Uniforms for Women

    DEFF Research Database (Denmark)

    Bjerck, Mari

    2016-01-01

    This article is makes use of fieldwork to discuss and analyse a Norwegian product development project aimed at developing workwear for women in male dominated manual occupations. Making use of ethnographic methods and analysis can be valuable in showing how users’ experiences and practices can...... relations and achieving action-oriented results may be a challenge in innovation and development processes. This article explores such challenges in studying the use of clothes in specific work contexts, as well as capturing and mediating this experience with workwear in use....

  8. Luminescence from cavitation bubbles deformed in uniform pressure gradients

    OpenAIRE

    Supponen, Outi; Obreschkow, Danail; Kobel, Philippe; Farhat, Mohamed

    2017-01-01

    Presented here are observations that demonstrate how the deformation of millimetric cavitation bubbles by a uniform pressure gradient quenches single collapse luminescence. Our innovative measurement system captures a broad luminescence spectrum (wavelength range 300-900 nm) from the individual collapses of laser-induced bubbles in water. By varying the bubble size, driving pressure and the perceived gravity level aboard parabolic flights, we probed the limit from aspherical to highly spheric...

  9. Uniform supersaturated design and its construction

    Institute of Scientific and Technical Information of China (English)

    方开泰; 葛根年; 刘民千

    2002-01-01

    Supersaturated designs are factorial designs in which the number of main effects is greater than the number of experimental runs. In this paper, a discrete discrepancy is proposed as a measure of uniformity for supersaturated designs, and a lower bound of this discrepancy is obtained asa benchmark of design uniformity. A construction method for uniform supersaturated designs via resolvable balanced incomplete block designs is also presented along with the investigation of properties of the resulting designs. The construction method shows a strong link between these two different kinds of designs.

  10. Whiteness formula in CIELAB uniform color space

    Institute of Scientific and Technical Information of China (English)

    Guoxin He; Mingxun Zhou

    2007-01-01

    @@ Many attempts have been made to standardize the calculation of whiteness. Whiteness formulas currently in use satisfactorily characterize the appearance of commercial whiteness. However, they have poor correlations with the observers' evaluations, and are often unsuccessful in assessing tinted white samples.A whiteness formula in the CIELAB uniform color space is developed in this paper. Several whiteness formulas are analyzed and compared. The experimental results show that the whiteness formula in the CIELAB uniform color space agrees well with the visual ranking, and it is superior to the CIE whiteness formula and the others in visual correlativity, uniformity and applicability.

  11. Temporal high-pass non-uniformity correction algorithm based on grayscale mapping and hardware implementation

    Science.gov (United States)

    Jin, Minglei; Jin, Weiqi; Li, Yiyang; Li, Shuo

    2015-08-01

    In this paper, we propose a novel scene-based non-uniformity correction algorithm for infrared image processing-temporal high-pass non-uniformity correction algorithm based on grayscale mapping (THP and GM). The main sources of non-uniformity are: (1) detector fabrication inaccuracies; (2) non-linearity and variations in the read-out electronics and (3) optical path effects. The non-uniformity will be reduced by non-uniformity correction (NUC) algorithms. The NUC algorithms are often divided into calibration-based non-uniformity correction (CBNUC) algorithms and scene-based non-uniformity correction (SBNUC) algorithms. As non-uniformity drifts temporally, CBNUC algorithms must be repeated by inserting a uniform radiation source which SBNUC algorithms do not need into the view, so the SBNUC algorithm becomes an essential part of infrared imaging system. The SBNUC algorithms' poor robustness often leads two defects: artifacts and over-correction, meanwhile due to complicated calculation process and large storage consumption, hardware implementation of the SBNUC algorithms is difficult, especially in Field Programmable Gate Array (FPGA) platform. The THP and GM algorithm proposed in this paper can eliminate the non-uniformity without causing defects. The hardware implementation of the algorithm only based on FPGA has two advantages: (1) low resources consumption, and (2) small hardware delay: less than 20 lines, it can be transplanted to a variety of infrared detectors equipped with FPGA image processing module, it can reduce the stripe non-uniformity and the ripple non-uniformity.

  12. Three-Dimensional Morphology Control Yielding Enhanced Hole Mobility in Air-Processed Organic Photovoltaics: Demonstration with Grazing-Incidence Wide-Angle X-ray Scattering

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Levi M. J. [School of Polymers; Bhattacharya, Mithun [School of Polymers; Wu, Qi [School of Polymers; Youm, Sang Gil [Department of Chemistry, Louisiana State University, 232 Choppin Hall, Baton Rouge, Louisiana 70803, United States; Nesterov, Evgueni E. [Department of Chemistry, Louisiana State University, 232 Choppin Hall, Baton Rouge, Louisiana 70803, United States; Morgan, Sarah E. [School of Polymers

    2017-06-28

    Polymer organic photovoltaic (OPV) device performance is defined by the three-dimensional morphology of the phase-separated domains in the active layer. Here, we determine the evolution of morphology through different stages of tailored solvent vapor and thermal annealing techniques in air-processed poly(3-hexylthiophene-2,5-diyl)/phenyl-C61-butyric acid methyl ester-based OPV blends. A comparative evaluation of the effect of solvent type used for vapor annealing was performed using grazing-incidence wide-angle X-ray scattering, atomic force microscopy, and UV–vis spectroscopy to probe the active-layer morphology. A nonhalogenated orthogonal solvent was found to impart controlled morphological features within the exciton diffusion length scales, enhanced absorbance, greater crystallinity, increased paracrystalline disorder, and improved charge-carrier mobility. Low-boiling, fast-diffusing isopropanol allowed the greatest control over the nanoscale structure of the solvents evaluated and yielded a cocontinuous morphology with narrowed domains and enhanced paths for the charge carrier to reach the anode.

  13. Green Building Challenge 98 (GBC 98) - process, boundary conditions, tools of assessment, demonstration projects. Final report; Green Building Challenge 98 (GBC 98) - Prozess, Rahmenwerk, Bewertungstool, Demonstrationsgebaeude. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Loehnert, G. [Solidar Planungsgesellschaft Architekten und Ingenieure, Berlin (Germany); Luetzkendorf, T. [Bauhaus-Universitaet Weimar (DE). Inst. fuer Ressourcenschonendes Bauen (IREB); Schuler, M. [TRANSSOLAR Energietechnik GmbH, Stuttgart (Germany); Kohler, N. [ifib, Universitaet Karlsruhe (TH) (Germany)

    2000-06-01

    Project goals: (a) Establishment of general definitions for green buildings on the basis of national and regional conditions for individualized application of an assessment system; (b) Transfer of environmentally and energy-relevant planning indicators from successful projects to other projects in order to produce multiplication effects; (c) Development of internationally comparable orientation aids and standards for green buildings, identification and documentation of exceptional and standard-setting buildings; (d) Development and follow-up of a long-term development process and information exchange for providing the preconditions for advertizing and marketing of green building concepts. [German] Zielsetzung und Anlass des Vorhabens: Entwicklung und Information ueber die Fortschritte und Umsetzungsmoeglichkeiten in der Bewertung von Leistungen und Qualitaeten umweltentlastender Bauweisen fuer Wissenschaftler, Planer und Bauherren. Die Projektziele verfolgen im einzelnen die: (a) Schaffung allgemeingueltiger Definitionen umweltgerechter Bauweisen (green buildings) auf der Basis nationaler / regional-spezifischer Bedingungen fuer die individuelle Anwendung eines Bewertungssystems (b) Uebertragung von umwelt- und energierelevanten Planungsindikatoren aus erfolgreichen Einzelprojekten auf andere Projekte zur Erzeugung von Multiplikatoreneffekten (c) Entwicklung international vergleichbarer Orientierungshilfen und Massstaebe fuer das umweltgerechte Gebaeude sowie die Identifizierung und Dokumentation aussergewoehnlicher und vorbildlicher Gebaeude (d) Foerderung und Pflege eines langfristigen Entwicklungsprozesses und Informationsaustausches mit dem Ziel, Voraussetzungen zur Werbung und Marktumsetzung 'gruener' Gebaeude-/Baukonzepte zu liefern. (orig.)

  14. Uniform spinning sampling gradient electron paramagnetic resonance imaging.

    Science.gov (United States)

    Johnson, David H; Ahmad, Rizwan; Liu, Yangping; Chen, Zhiyu; Samouilov, Alexandre; Zweier, Jay L

    2014-02-01

    To improve the quality and speed of electron paramagnetic resonance imaging (EPRI) acquisition by combining a uniform sampling distribution with spinning gradient acquisition. A uniform sampling distribution was derived for spinning gradient EPRI acquisition (uniform spinning sampling, USS) and compared to the existing (equilinear spinning sampling, ESS) acquisition strategy. Novel corrections were introduced to reduce artifacts in experimental data. Simulations demonstrated that USS puts an equal number of projections near each axis whereas ESS puts excessive projections at one axis, wasting acquisition time. Artifact corrections added to the magnetic gradient waveforms reduced noise and correlation between projections. USS images had higher SNR (85.9 ± 0.8 vs. 56.2 ± 0.8) and lower mean-squared error than ESS images. The quality of the USS images did not vary with the magnetic gradient orientation, in contrast to ESS images. The quality of rat heart images was improved using USS compared to that with ESS or traditional fast-scan acquisitions. A novel EPRI acquisition which combines spinning gradient acquisition with a uniform sampling distribution was developed. This USS spinning gradient acquisition offers superior SNR and reduced artifacts compared to prior methods enabling potential improvements in speed and quality of EPR imaging in biological applications. Copyright © 2013 Wiley Periodicals, Inc.

  15. DOA and Polarization Estimation Using an Electromagnetic Vector Sensor Uniform Circular Array Based on the ESPRIT Algorithm

    Directory of Open Access Journals (Sweden)

    Na Wu

    2016-12-01

    Full Text Available In array signal processing systems, the direction of arrival (DOA and polarization of signals based on uniform linear or rectangular sensor arrays are generally obtained by rotational invariance techniques (ESPRIT. However, since the ESPRIT algorithm relies on the rotational invariant structure of the received data, it cannot be applied to electromagnetic vector sensor arrays (EVSAs featuring uniform circular patterns. To overcome this limitation, a fourth-order cumulant-based ESPRIT algorithm is proposed in this paper, for joint estimation of DOA and polarization based on a uniform circular EVSA. The proposed algorithm utilizes the fourth-order cumulant to obtain a virtual extended array of a uniform circular EVSA, from which the pairs of rotation invariant sub-arrays are obtained. The ESPRIT algorithm and parameter pair matching are then utilized to estimate the DOA and polarization of the incident signals. The closed-form parameter estimation algorithm can effectively reduce the computational complexity of the joint estimation, which has been demonstrated by numerical simulations.

  16. Improving uniformity in brain death determination policies over time

    Science.gov (United States)

    Wang, Hilary H.; Varelas, Panayiotis N.; Henderson, Galen V.; Wijdicks, Eelco F.M.

    2017-01-01

    Objective: To demonstrate that progress has been made in unifying brain death determination guidelines in the last decade by directly comparing the policies of the US News and World Report's top 50 ranked neurologic institutions from 2006 and 2015. Methods: We solicited official hospital guidelines in 2015 from these top 50 institutions, generated summary statistics of their criteria as benchmarked against the American Academy of Neurology Practice Parameters (AANPP) and the comparison 2006 cohort in 5 key categories, and statistically compared the 2 cohorts' compliance with the AANPP. Results: From 2008 to 2015, hospital policies exhibited significant improvement (p = 0.005) in compliance with official guidelines, particularly with respect to criteria related to apnea testing (p = 0.009) and appropriate ancillary testing (p = 0.0006). However, variability remains in other portions of the policies, both those with specific recommendation from the AANPP (e.g., specifics for ancillary tests) and those without firm guidance (e.g., the level of involvement of neurologists, neurosurgeons, or physicians with education/training specific to brain death in the determination process). Conclusions: While the 2010 AANPP update seems to be concordant with progress in achieving greater uniformity in guidelines at the top 50 neurologic institutions, more needs to be done. Whether further interventions come as grassroots initiatives that leverage technological advances in promoting adoption of new guidelines or as top-down regulatory rulings to mandate speedier approval processes, this study shows that solely relying on voluntary updates to professional society guidelines is not enough. PMID:28077490

  17. Uniform Stability of a Class of Fractional-Order Nonautonomous Systems with Multiple Time Delays

    Directory of Open Access Journals (Sweden)

    Tao Zou

    2014-01-01

    sufficient condition is established for the existence and uniqueness of solutions for such systems involving Caputo fractional derivative, and the uniform stability of solution is studied. At last, two examples are given to demonstrate the applicability of our results.

  18. Uniform Facility Data Set US (UFDS-1997)

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Uniform Facility Data Set (UFDS), formerly the National Drug and Alcohol Treatment Unit Survey or NDATUS, was designed to measure the scope and use of drug abuse...

  19. Uniform Facility Data Set US (UFDS-1998)

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Uniform Facility Data Set (UFDS) was designed to measure the scope and use of drug abuse treatment services in the United States. The survey collects information...

  20. 7 CFR 29.3563 - Uniformity.

    Science.gov (United States)

    2010-01-01

    ... INSPECTION Standards Official Standard Grades for Dark Air-Cured Tobacco (u.s. Types 35, 36, 37 and Foreign... tobacco as it is prepared for market. Uniformity is expressed in grade specifications as a percentage....

  1. On uniform exponential growth for solvable groups

    OpenAIRE

    Breuillard, Emmanuel

    2006-01-01

    Using a theorem of J. Groves we give a ping-pong proof of Osin's uniform exponential growth for solvable groups. We discuss slow exponential growth and show that this phenomenon disappears as one passes to a finite index subgroup.

  2. Orbifoldization, covering surfaces and uniformization theory

    CERN Document Server

    Bántay, P

    1998-01-01

    The connection between the theory of permutation orbifolds, covering surfaces and uniformization is investigated, and the higher genus partition functions of an arbitrary permutation orbifold are expressed in terms of those of the original theory.

  3. Completions of pre–uniform spaces

    OpenAIRE

    Adalberto García-Máynez; Rubén Mancio-Toledo

    2007-01-01

    [EN] In this paper we prove the existence of a completion of a T0–pre-uniform space (X,U), with the property that each Cauchy filter in (X,U) contains a weakly round filter. García-Máynez, A.; Mancio-Toledo, R. (2007). Completions of pre–uniform spaces. Applied General Topology. 8(2):213-221. doi:10.4995/agt.2007.1882. 213 221 8 2

  4. A facile electrochemical route to the preparation of uniform and monoatomic copper shells for gold nanoparticles.

    Science.gov (United States)

    Gründer, Y; Ramasse, Q M; Dryfe, R A W

    2015-02-28

    Copper on gold forms a monolayer deposit via underpotential deposition. For gold particles adsorbed at a liquid-liquid interface this results in a uniform one monolayer thick shell. This approach offers a new route for the uniform functionalisation of nanoparticles and presents a way to probe fundamental processes that underlie nanoparticle synthesis.

  5. 硝化体系及精制棉干燥处理对硝化棉含氮量均匀性的影响%Effect of Nitrification System and Refined Cotton Drying Process on the Nitrogen Distribution Uniformity of Nitrocellulose

    Institute of Scientific and Technical Information of China (English)

    张云华; 邵自强; 王文俊; 王飞後; 吕少一

    2013-01-01

    Polarizing microscope has been used to investigate the nitrogen distribution uniformity of nitrocellulose (NC) prepared from cotton linters which are refined by different pretreatment methods, and one of nitrating system is ordinary mixtures of nitric and sulfuric acids and water while the other one is green sulfur-free nitrating system - HNO3/CH2C12. The results show that the uniformity of the product of nitrification will change obviously as the treatment of raw cotton cellulose changing, the performance of NC has a more obvious change if the raw cotton cellulose containing water be dried, because of the role of keratinization during the drying process of the cotton cellulose. The role of the keratinization makes the nitrogen content and nitrogen distribution uniformity of NC worse than that NC prepared from cotton linters without being dried. The homogeneity of nitrocellulose changes regularly at different nitrogen content levels, NC with mid-nitrogen content, such as 12%, has a better uniformity than those with 13% or 11%.%将不同预处理方法得到的精制棉在普通硝硫混酸体系和绿色无硫硝化体系(HNO3/CH2Cl2)中进行硝化,采用偏光显微镜研究了产物硝化的均匀性.结果表明,改变原料棉纤维素处理方法,产物硝化的均匀性有较明显的变化,对原料棉纤维素进行干燥处理后,硝化产物性能有较明显的变化,适当含有水分的棉纤维素干燥处理后,由于角质化作用,制得的硝化棉(NC)含氮量和硝化均匀性比干燥处理前均有所降低;含氮量不同,产品的硝化均匀性有规律性变化,在中含氮量(如12%)时,NC的均匀性比含氮量为13%或11%的硝化棉好.

  6. Uniform and Complementary Social Interaction: Distinct Pathways to Solidarity.

    Science.gov (United States)

    Koudenburg, Namkje; Postmes, Tom; Gordijn, Ernestine H; van Mourik Broekman, Aafke

    2015-01-01

    We examine how different forms of co-action give rise to feelings of solidarity. We propose that (a) coordinated action elicits a sense of solidarity, and (b) the process through which such solidarity emerges differs for different forms of co-action. We suggest that whether solidarity within groups emerges from uniform action (e.g. synchronizing, as when people speak in unison) or from more complementary forms of action (e.g. alternating, when speaking in turns) has important consequences for the emergent position of individuals within the group. Uniform action relies on commonality, leaving little scope for individuality. In complementary action each individual makes a distinctive contribution to the group, thereby increasing a sense of personal value to the group, which should contribute to the emergence of solidarity. The predictions receive support from five studies, in which we study groups in laboratory and field settings. Results show that both complementary and uniform co-action increase a sense of solidarity compared to control conditions. However, in the complementary action condition, but not in the uniform action (or synchrony) condition, the effect on feelings of solidarity is mediated by a sense of personal value to the group.

  7. Gravitation collapse of spherical symmetry with non-uniform density

    Institute of Scientific and Technical Information of China (English)

    GU Chao-hao

    2006-01-01

    A star with sufficiently large mass will collapse in its senectitude because of gravitation.Many researchers have tried to describe this collapse process.Investigations have been conducted in the case that the star has spherical symmetry and the initial density is uniform.In this article,the case that the initial density is not uniform will be considered.When the density function is high in the center and decreasing with the radius,the collapse process will be described,and in this case,the singularity will only come out in the center because of collision.If the density is not monotonic and there is a crust with high density around the star,it is proved that the non-central collision singularity may come out either in the Schwarzschild sphere or outside of it,i.e.,the naked singularize may come out.

  8. Modified Richardson Number in Non-Uniform Saturated Moist Flow

    Institute of Scientific and Technical Information of China (English)

    YANG Shuai; GAO Shou-Ting

    2006-01-01

    @@ As a useful index, I.e. The Richardson number Ri, is modified in non-uniform saturated moist flow, based on the fact that liquid water is partially dropped out in parcel air. This is more realistic in real moist atmosphere,especially in the rainfall process. The modified Ri presents adequately the influence of numerator, I.e. Brunt-Vaisala frequency (BVF), on instability. Compared to several former formulae generalized by Durran and Klemp,the modified Ri evidently decreases the stability in rainy regions. In theory, the modified BVF and Ri fix the discontinuity of latent heat release in the transition areas between saturated and unsaturated air by introducing the condensation probability function. Furthermore, the diagnostic analysis of the modilied Ri validates the rationality of its application in the non-uniform saturated moist process.

  9. Fabrication of uniform DNA-conjugated hydrogel microparticles via replica molding for facile nucleic acid hybridization assays.

    Science.gov (United States)

    Lewis, Christina L; Choi, Chang-Hyung; Lin, Yan; Lee, Chang-Soo; Yi, Hyunmin

    2010-07-01

    We identify and investigate several critical parameters in the fabrication of single-stranded DNA conjugated poly(ethylene glycol) (PEG) microparticles based on replica molding (RM) for highly uniform and robust nucleic acid hybridization assays. The effects of PEG-diacrylate, probe DNA, and photoinitiator concentrations on the overall fluorescence and target DNA penetration depth upon hybridization are examined. Fluorescence and confocal microscopy results illustrate high conjugation capacity of the probe and target DNA, femtomole sensitivity, and sequence specificity. Combined, these findings demonstrate a significant step toward simple, robust, and scalable procedures to manufacture highly uniform and high-capacity hybridization assay particles in a well-controlled manner by exploiting many advantages that the batch processing-based RM technique offers. We envision that the results presented here may be readily applied to rapid and high-throughput hybridization assays for a wide variety of applications in bioprocess monitoring, food safety, and biological threat detection.

  10. A micro-reactor for preparing uniform molecularly imprinted polymer beads.

    Science.gov (United States)

    Zourob, Mohammed; Mohr, Stephan; Mayes, Andrew G; Macaskill, Alexandra; Pérez-Moral, Natalia; Fielden, Peter R; Goddard, Nicholas J

    2006-02-01

    In this study, uniform spherical molecularly imprinted polymer beads were prepared via controlled suspension polymerization in a spiral-shaped microchannel using mineral oil and perfluorocarbon liquid as continuous phases. Monodisperse droplets containing the monomers, template, initiator, and porogenic solvent were introduced into the microchannel, and particles of uniform size were produced by subsequent UV polymerization, quickly and without wasting polymer materials. The droplet/particle size was varied by changing the flow conditions in the microfluidic device. The diameter of the resulting products typically had a coefficient of variation (CV) below 2%. The specific binding sites that were created during the imprinting process were analysed via radioligand binding analysis. The molecularly imprinted microspheres produced in the liquid perfluorocarbon continuous phase had a higher binding capacity compared with the particles produced in the mineral oil continuous phase, though it should be noted that the aim of this study was not to optimize or maximize imprinting performance, but rather to demonstrate broad applicability and compatibility with known MIP production methods. The successful imprinting against a model compound using two very different continuous phases (one requiring a surfactant to stabilize the droplets the other not) demonstrates the generality of this current simple approach.

  11. Optimization of forging process concerning deformation uniformity and crack%关于变形均匀性与金属裂纹的锻造工艺优化设计

    Institute of Scientific and Technical Information of China (English)

    肖石霞; 梅益; 陈美丽; 王艳晓

    2011-01-01

    针对平砧镦粗过程中变形不均匀,出现鼓形,金属产生裂纹甚至断裂等现象,以刚粘塑性有限元法为基础,提出了基于数值模拟的优化方法.建立数学模型、构造总目标函数,并结合正交试验,以每步压下量、始锻温度和锻锤击打速度为设计变量进行模拟,分析每个变量对目标函数的影响,并将得到的最优工艺方案成功运用到实际生产.%In view of existence of inhomogeneous deformation, drum, crack and even fracture in the process of flat anvil and upsetting, an optimization method based on rigid-visco-plastic FEM and numerical simulation was presented. In this study, a mathematical model and a general objective function were built up, and combining orthogonal test, parameters like every step reduction amount, initial forging temperature and speed of forging hammer were used as variables to carry out simulation, in which way the effect of each variable on the objective function was researched.

  12. Depreciation accounting in the uniform chart of accounts.

    OpenAIRE

    George, Charles Lee

    1982-01-01

    Approved for public release; distribution is unlimited This paper examines depreciation's contribution to the total cost of providing health care. In particular it analyzes the depreciation method used to measure the consumption of health care resources, the validity of the depreciation process and the subsequent allocation procedures. As defined by the Uniform Chart of Accounts, the usefulness of depreciation in determining the total cost of providing health care is atte...

  13. Jennings Demonstration PLant

    Energy Technology Data Exchange (ETDEWEB)

    Russ Heissner

    2010-08-31

    Verenium operated a demonstration plant with a capacity to produce 1.4 million gallons of cellulosic ethanol from agricultural resiues for about two years. During this time, the plant was able to evaluate the technical issues in producing ethanol from three different cellulosic feedstocks, sugar cane bagasse, energy cane, and sorghum. The project was intended to develop a better understanding of the operating parameters that would inform a commercial sized operation. Issues related to feedstock variability, use of hydrolytic enzymes, and the viability of fermentative organisms were evaluated. Considerable success was achieved with pretreatment processes and use of enzymes but challenges were encountered with feedstock variability and fermentation systems. Limited amounts of cellulosic ethanol were produced.

  14. Layer-modulated synthesis of uniform tungsten disulfide nanosheet using gas-phase precursors.

    Science.gov (United States)

    Park, Jusang; Lee, Wonseon; Choi, Taejin; Hwang, Sung-Hwan; Myoung, Jae Min; Jung, Jae-Hoon; Kim, Soo-Hyun; Kim, Hyungjun

    2015-01-28

    The synthesis of layered transition-metal-disulfide (MS2, M = Mo, W) nanosheets with layer controllability and large-area uniformity is an essential requirement for their application in electronic and optical devices. In this report, we describe a synthesis process of WS2 nanosheets with layer controllability and high uniformity using chemical vapor deposition (CVD) and WCl6 and H2S as gas-phase precursors. Through this process, we can systematically modulate the thickness of WS2 nanosheets by controlling the duration of the reaction between WCl6 and H2S. The CVD-grown WS2 nanosheets exhibit good stoichiometry as well as dependencies of a clear Raman shift and bandgap on the number of layers. These properties are confirmed by X-ray photoemission spectroscopy, Raman spectroscopy, and photoluminescence measurements. The number of layers of WS2 nanosheets is confirmed by atomic force microscopy. Finally, we demonstrate the fabrication and performance of a photodetector based on a hybrid structure consisting of graphene and a WS2 nanosheet.

  15. Non-uniform sampled scalar diffraction calculation using non-uniform fast Fourier transform

    CERN Document Server

    Shimobaba, Tomoyoshi; Oikawa, Minoru; Okada, Naohisa; Endo, Yutaka; Hirayama, Ryuji; Ito, Tomoyoshi

    2013-01-01

    Scalar diffraction calculations such as the angular spectrum method (ASM) and Fresnel diffraction, are widely used in the research fields of optics, X-rays, electron beams, and ultrasonics. It is possible to accelerate the calculation using fast Fourier transform (FFT); unfortunately, acceleration of the calculation of non-uniform sampled planes is limited due to the property of the FFT that imposes uniform sampling. In addition, it gives rise to wasteful sampling data if we calculate a plane having locally low and high spatial frequencies. In this paper, we developed non-uniform sampled ASM and Fresnel diffraction to improve the problem using the non-uniform FFT.

  16. Spherical Accretion in a Uniformly Expanding Universe

    Science.gov (United States)

    Colpi, Monica; Shapiro, Stuart L.; Wasserman, Ira

    1996-10-01

    We consider spherically symmetric accretion of material from an initially homogeneous, uniformly expanding medium onto a Newtonian point mass M. The gas is assumed to evolve adiabatically with a constant adiabatic index F, which we vary over the range Γ ɛ [1, 5/3]. We use a one-dimensional Lagrangian code to follow the spherical infall of material as a function of time. Outflowing shells gravitationally bound to the point mass fall back, giving rise to a inflow rate that, after a rapid rise, declines as a power law in time. If there were no outflow initially, Bondi accretion would result, with a characteristic accretion time-scale ta,0. For gas initially expanding at a uniform rate, with a radial velocity U = R/t0 at radius R, the behavior of the flow at all subsequent times is determined by ta,0/t0. If ta,0/t0 ≫ 1, the gas has no time to respond to pressure forces, so the fluid motion is nearly collisionless. In this case, only loosely bound shells are influenced by pressure gradients and are pushed outward. The late-time evolution of the mass accretion rate Mdot is close to the result for pure dust, and we develop a semianalytic model that accurately accounts for the small effect of pressure gradients in this limit. In the opposite regime, ta,0/t0 ≪ 1, pressure forces significantly affect the motion of the gas. At sufficiently early times, t ≤ ttr, the flow evolved along a sequence of quasi-stationary, Bondi-like states, with a time-dependent Mdot determined by the slowly varying gas density at large distances. However, at later times, t ≥ ttr, the fluid flow enters a dustllke regime; ttr is the time when the instantaneous Bondi accretion radius reaches the marginally bound radius. The transition time ttr depends sensitively on ta,0/t0 for a given Γ and can greatly exceed t0. We show that there exists a critical value Γ = 11/9, below which the transition from fluid to ballistic motion disappears. As one application of our calculations, we consider the

  17. Development of a phantom and assessment of (141)Ce as a surrogate radionuclide for flood field uniformity testing of gamma cameras.

    Science.gov (United States)

    Saxena, Sanjay Kumar; Kumar, Yogendra; Malpani, Basant; Rakshit, Sutapa; Dash, Ashutosh

    2016-06-01

    This paper describes an indigenous method for development and deployment of rechargeable liquid filled phantom with newly proposed radionuclide (141)Ce for determination of extrinsic uniformity of gamma cameras. Details about design of phantom, neutron irradiation of cerium targets, chemical processing of (141)Ce, charging of phantom with (141)Ce solution and their performance evaluation are presented. Suitability of (141)Ce in quality assurance of gamma cameras used in in-vivo diagnostic imaging procedures has been amply demonstrated.

  18. Nurses' uniform: an investigation of mobility.

    Science.gov (United States)

    Stubbs, D A; Buckle, P W; Hudson, M P; Butler, P E; Rivers, P M

    1985-01-01

    An investigation of the mobility of nurses under three clothing conditions is reported. The need for such a study has arisen as a result of the concern over a possible mismatch between mobility and patient handling requirements. Thirty-seven nurses participated under two of the clothing conditions ('National' dress uniform, Trouser/tunic combination). In addition, ten of these nurses volunteered to provide control data by being measured in a leotard or a swimming costume. Eleven static and sixteen dynamic anthropometric measures were considered. Each nurse was asked to complete a short questionnaire, relating to her subjective attitudes to the uniform and to her own physical state at the time of measurement. Whilst both uniforms imposed restrictions on the shoulder girdle and trunk of up to 10%, the area of greatest concern was the mobility of the hip joint. Hip flexion was reduced by 26% in the dress uniform. The implications of these findings for patient handling procedures are discussed, as are those of the relationship between the environment and the material. Uniform and the nursing image is also considered.

  19. Mask CD uniformity improvement by electron scanning exposure based Global Loading Effect Correction

    Science.gov (United States)

    Li, Rivan; Tian, Eric; Shi, Irene; Guo, Eric; Lu, Max

    2015-07-01

    Critical Dimension (CD) Uniformity is one of the necessary parameters to assure good performance and reliable functionality of any integrated circuit (IC), and towards the advanced technology node 28nm and beyond, corresponding CD Uniformity becomes more and more crucial. It is found that bad mask CD Uniformity is a significant error source at 28nm process. The CD Uniformity on mask, if not controlled well, will badly impact wafer CD performance, and it has been well-studied that CD Uniformity issue from gate line-width in transistors would affect the device performance directly. In this paper we present a novel solution for mask global CD uniformity error correction, which is called as global loading effect correction (GLEC) method and applied nesting in the mask exposure map during the electron beam exposure. There are factors such as global chip layout, writing sequence and chip pattern density distribution (Global Loading), that work on the whole mask CD Uniformity, especially Global Loading is the key factor related to mask global CD error. From our experimental results, different pattern density distribution on mask significantly influenced the final mask CD Uniformity: the mask with undulating pattern density distribution provides much worse CD Uniformity than that with uniform one. Therefore, a GLEC model based on pattern density has been created to compensate the global error during the electron beam exposure, which has been proved to be efficacious to improve mask global CD Uniformity performance. Furthermore, it 's also revealed that pattern type is another important impact factor, and GLEC coefficient need be modified due to the specific pattern type (e.g. dense line-space only, iso-space only or an average of them) to improve the corresponding mask CD uniformity.

  20. The segmented non-uniform dielectric module design for uniformity control of plasma profile in a capacitively coupled plasma chamber

    Directory of Open Access Journals (Sweden)

    Huanxiong Xia

    2014-12-01

    Full Text Available Low-temperature plasma technique is one of the critical techniques in IC manufacturing process, such as etching and thin-film deposition, and the uniformity greatly impacts the process quality, so the design for the plasma uniformity control is very important but difficult. It is hard to finely and flexibly regulate the spatial distribution of the plasma in the chamber via controlling the discharge parameters or modifying the structure in zero-dimensional space, and it just can adjust the overall level of the process factors. In the view of this problem, a segmented non-uniform dielectric module design solution is proposed for the regulation of the plasma profile in a CCP chamber. The solution achieves refined and flexible regulation of the plasma profile in the radial direction via configuring the relative permittivity and the width of each segment. In order to solve this design problem, a novel simulation-based auto-design approach is proposed, which can automatically design the positional sequence with multi independent variables to make the output target profile in the parameterized simulation model approximate the one that users preset. This approach employs an idea of quasi-closed-loop control system, and works in an iterative mode. It starts from initial values of the design variable sequences, and predicts better sequences via the feedback of the profile error between the output target profile and the expected one. It never stops until the profile error is narrowed in the preset tolerance.

  1. The Complexity of Synthesizing Uniform Strategies

    Directory of Open Access Journals (Sweden)

    Bastien Maubert

    2013-03-01

    Full Text Available We investigate uniformity properties of strategies. These properties involve sets of plays in order to express useful constraints on strategies that are not μ-calculus definable. Typically, we can state that a strategy is observation-based. We propose a formal language to specify uniformity properties, interpreted over two-player turn-based arenas equipped with a binary relation between plays. This way, we capture e.g. games with winning conditions expressible in epistemic temporal logic, whose underlying equivalence relation between plays reflects the observational capabilities of agents (for example, synchronous perfect recall. Our framework naturally generalizes many other situations from the literature. We establish that the problem of synthesizing strategies under uniformity constraints based on regular binary relations between plays is non-elementary complete.

  2. Uniform dimension results for Gaussian random fields

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Let X = {X(t),t ∈ RN} be a Gaussian random field with values in Rd defined by X(t) =(X1(t),...,Xd(t)), t ∈ RN.(1) The properties of space and time anisotropy of X and their connections to uniform Hausdorff dimension results are discussed.It is shown that in general the uniform Hausdorff dimension result does not hold for the image sets of a space-anisotropic Gaussian random field X.When X is an(N,d)-Gaussian random field as in(1),where X1,...,Xd are independent copies of a real valued,centered Gaussian random field X0 which is anisotropic in the time variable.We establish uniform Hausdorff dimension results for the image sets of X.These results extend the corresponding results on one-dimensional Brownian motion,fractional Brownian motion and the Brownian sheet.

  3. Elastic stability of non-uniform columns

    Science.gov (United States)

    Lee, S. Y.; Kuo, Y. H.

    1991-07-01

    A simple and efficient method is proposed to investigate the elastic stability of three different tapered columns subjected to uniformly distributed follower forces. The influences of the boundary conditions and taper ratio on critical buckling loads are investigated. The critical buckling loads of columns of rectangular cross section with constant depth and linearly varied width ( T1), constant width and linearly varied depth ( T2) and double taper ( T3) are investigated. Among the three different non-uniform columns considered, taper ratio has the greatest influence on the critical buckling load of column T3 and the lowest influence on that of column T1. The types of instability mechanisms for hinged-hinged and cantilever non-uniform columns are divergence and flutter respectively. However, for clamped-hinged and clamped-clamped non-uniform columns, the type of instability mechanism for column T1 is divergence, while that for columns T2 and T3 is divergence only when the taper ratio of the columns is greater than certain critical values and flutter for the rest value of taper ratio. When the type of instability mechanism changes from divergence to flutter, there is a finite jump for the critical buckling load. The influence of taper ratio on the elastic stability of cantilever column T3 is very sensitive for small values of the taper ratio and there also exist some discontinieties in the critical buckling loads of flutter instability. For a hinged-hinged non-uniform column ( T2 or T3) with a rotational spring at the left end of the column, when the taper ratio is less than the critical value the instability mechanism changes from divergence to flutter as the rotational spring constant is increased. For a clamped-elastically supported non-uniform column, when the taper ratio is greater than the critical value the instability mechanism changes from flutter to divergence as the translational spring constant is increased.

  4. Non-uniformly weighted sampling for faster localized two-dimensional correlated spectroscopy of the brain in vivo

    Science.gov (United States)

    Verma, Gaurav; Chawla, Sanjeev; Nagarajan, Rajakumar; Iqbal, Zohaib; Albert Thomas, M.; Poptani, Harish

    2017-04-01

    Two-dimensional localized correlated spectroscopy (2D L-COSY) offers greater spectral dispersion than conventional one-dimensional (1D) MRS techniques, yet long acquisition times and limited post-processing support have slowed its clinical adoption. Improving acquisition efficiency and developing versatile post-processing techniques can bolster the clinical viability of 2D MRS. The purpose of this study was to implement a non-uniformly weighted sampling (NUWS) scheme for faster acquisition of 2D-MRS. A NUWS 2D L-COSY sequence was developed for 7T whole-body MRI. A phantom containing metabolites commonly observed in the brain at physiological concentrations was scanned ten times with both the NUWS scheme of 12:48 duration and a 17:04 constant eight-average sequence using a 32-channel head coil. 2D L-COSY spectra were also acquired from the occipital lobe of four healthy volunteers using both the proposed NUWS and the conventional uniformly-averaged L-COSY sequence. The NUWS 2D L-COSY sequence facilitated 25% shorter acquisition time while maintaining comparable SNR in humans (+0.3%) and phantom studies (+6.0%) compared to uniform averaging. NUWS schemes successfully demonstrated improved efficiency of L-COSY, by facilitating a reduction in scan time without affecting signal quality.

  5. Uniform wire segmentation algorithm of distributed interconnects

    Institute of Scientific and Technical Information of China (English)

    Yin Guoli; Lin Zhenghui

    2007-01-01

    A uniform wire segmentation algorithm for performance optimization of distributed RLC interconnects was proposed in this paper. The optimal wire length for identical segments and buffer size for buffer insertion are obtained through computation and derivation, based on a 2-pole approximation model of distributed RLC interconnect. For typical inductance value and long wires under 180nm technology, experiments show that the uniform wire segmentation technique proposed in the paper can reduce delay by about 27% ~ 56% , while requires 34%~69% less total buffer usage and thus 29% to 58% less power consumption. It is suitable for long RLC interconnect performance optimization.

  6. Uniform topology on EQ-algebras

    Directory of Open Access Journals (Sweden)

    Yang Jiang

    2017-04-01

    Full Text Available In this paper, we use filters of an EQ-algebra E to induce a uniform structure (E, , and then the part induce a uniform topology in E. We prove that the pair (E, is a topological EQ-algebra, and some properties of (E, are investigated. In particular, we show that (E, is a first-countable, zero-dimensional, disconnected and completely regular space. Finally, by using convergence of nets, the convergence of topological EQ-algebras is obtained.

  7. Asynchronous signal-dependent non-uniform sampler

    Science.gov (United States)

    Can-Cimino, Azime; Chaparro, Luis F.; Sejdić, Ervin

    2014-05-01

    Analog sparse signals resulting from biomedical and sensing network applications are typically non-stationary with frequency-varying spectra. By ignoring that the maximum frequency of their spectra is changing, uniform sampling of sparse signals collects unnecessary samples in quiescent segments of the signal. A more appropriate sampling approach would be signal-dependent. Moreover, in many of these applications power consumption and analog processing are issues of great importance that need to be considered. In this paper we present a signal dependent non-uniform sampler that uses a Modified Asynchronous Sigma Delta Modulator which consumes low-power and can be processed using analog procedures. Using Prolate Spheroidal Wave Functions (PSWF) interpolation of the original signal is performed, thus giving an asynchronous analog to digital and digital to analog conversion. Stable solutions are obtained by using modulated PSWFs functions. The advantage of the adapted asynchronous sampler is that range of frequencies of the sparse signal is taken into account avoiding aliasing. Moreover, it requires saving only the zero-crossing times of the non-uniform samples, or their differences, and the reconstruction can be done using their quantized values and a PSWF-based interpolation. The range of frequencies analyzed can be changed and the sampler can be implemented as a bank of filters for unknown range of frequencies. The performance of the proposed algorithm is illustrated with an electroencephalogram (EEG) signal.

  8. New process for the wastewater reclamation. ACTDisc process demonstration in the WWTP at Castellon de la Plana (Spain); Nuevos procesos de regeneracion de aguas depuradas: demostracion del proceso ACTDisc en la EDAR de Castellon de la Plana

    Energy Technology Data Exchange (ETDEWEB)

    Sanz, J.; Guerrero, L.; Ortega, J. M.; Ferrer, C.; Migeul, D.; Martinez, F.; Morenilla Martinez, J. J.; Bernacer Bonora, I.

    2006-07-01

    During May 2005, the efficiency of ACTIDis process has been rested in Castellon de la Plana WWTP, in collaboration with Fecsa and Entitat de Sanejament d'Aigues Residuals de la Generalitat Valenciana. Test purpose has been to prove the suitability of ACTIDisc process in wastewater reclamation of this WWTP secondary effluent. The aim has been, mainly, to achieve a low level of suspended solid and turbidity in compliance with the regulations proposal for direct reuse of treated effluents as AEAS guidelines suggested in 2005. (Author) 6 refs.

  9. Non-Uniform Heat Transfer in Thermal Regenerators

    DEFF Research Database (Denmark)

    Jensen, Jesper Buch

    This thesis presents investigations on the heat transfer in complex heat ex- changers in general and in regenerative heat exchangers (regenerators) in par- ticular. The motivation for this work is a result of inconsistencies obeserved in the results from a series of experiments on active magnetic...... regenerators (AMRs) with parallel plates. The results suggest that random variations in the regenerator geometries causes maldistributed fluid flow inside the regener- ators, which affects the regenerator performance. In order to study the heat transfer processes in regenerators with non-uniform geometries......, a numerical model, which simulates a single-blow operation in a parallel-plate regenerator, was developed and used to model the heat transfer under various conditions. In addition to the modeling of the heat transfer, a series of experiments on passive regenerators with non-uniform, but precisely controlled...

  10. Contiguous Uniform Deviation for Multiple Linear Regression in Pattern Recognition

    Science.gov (United States)

    Andriana, A. S.; Prihatmanto, D.; Hidaya, E. M. I.; Supriana, I.; Machbub, C.

    2017-01-01

    Understanding images by recognizing its objects is still a challenging task. Face elements detection has been developed by researchers but not yet shows enough information (low resolution in information) needed for recognizing objects. Available face recognition methods still have error in classification and need a huge amount of examples which may still be incomplete. Another approach which is still rare in understanding images uses pattern structures or syntactic grammars describing shape detail features. Image pixel values are also processed as signal patterns which are approximated by mathematical function curve fitting. This paper attempts to add contiguous uniform deviation method to curve fitting algorithm to increase applicability in image recognition system related to object movement. The combination of multiple linear regression and contiguous uniform deviation method are applied to the function of image pixel values, and show results in higher resolution (more information) of visual object detail description in object movement.

  11. Strategy Uniform Crossover Adaptation Evolution in a Minority Game

    Institute of Scientific and Technical Information of China (English)

    杨伟松; 汪秉宏; 全宏俊; 胡进锟

    2003-01-01

    We propose a new adaptation minority game for understanding the complex dynamical behaviour characterized by agent interactions competing limited resources in many natural and social systems. Intelligent agents may modify a part of their strategies periodically, depending on the strategyperformances. In the present model, the strategies will be updated according to a uniform-crossover variation process inspired by genetic evolution algorithm in biology. The performances of the agents in our model are calculated for different parameter conditions. It has been found that the new system may evolve via the strategy uniform crossover adaptation mechanism into a frozen equilibrium state in which the performance of the system may reach the best limit, implying the strongest cooperation among agents and the most effective utilization of the social resources.

  12. Application of uniform DFT filter bank in radar jamming system

    Institute of Scientific and Technical Information of China (English)

    Dai Le; Gao Meiguo

    2006-01-01

    The principle of Uniform DFT filter bank is presented. Exploiting poly-phase structure, radar jamming system samples the intercepted wideband radar signals through analysis filter bank by different channels and linearly modulates the intercepted radar signal according to the theory of signal and system, then synthesizes the jamming signal through the synthesis filter bank. The method merely requires lower sample frequency, reduces the computational complexity and the data quantity to be processed. The un-ideal filter's influence to the result of signals processing is analyzed by simulating the match filter in radar jamming system.

  13. Stability analysis of uniform equilibrium foam states for EOR processes

    NARCIS (Netherlands)

    Ashoori, E.; Marchesin, D.; Rossen, W.R.

    2011-01-01

    The use of foam for mobility control is a promising mean to improve sweep efficiency in EOR. Experimental studies discovered that foam exhibits three different states (weak foam, intermediate foam, and strong foam). The intermediate-foam state is found to be unstable in the lab whereas the weak- and

  14. Uniform design of experiments with mixtures

    Institute of Scientific and Technical Information of China (English)

    王元; 方开泰

    1996-01-01

    Consider a design of experiments with mixtures:0≤aiuniform distribution in number theory.

  15. Apartness and uniformity a constructive development

    CERN Document Server

    Bridges, Douglas S

    2011-01-01

    This book presents a theory of apartness encompassing both point-set topology and the theory of uniform spaces. The first book on the apartness approach to constructive topology, it is a valuable addition to the literature on topology in computer science.

  16. Towards a uniform analysis of 'any'

    NARCIS (Netherlands)

    van Rooij, R.

    2008-01-01

    In this paper, Universal any and Negative Polarity Item any are uniformly analyzed as ‘counterfactual’ donkey sentences (in disguise). Their difference in meaning is reduced here to the distinction between strong and weak readings of donkey sentences. It is shown that this explains the universal and

  17. School Uniforms in Urban Public High Schools

    Science.gov (United States)

    Draa, Virginia Ann Bendel

    2005-01-01

    The purpose of this study was to determine whether or not the implementation of a mandatory uniform policy in urban public high schools improved school performance measures at the building level for rates of attendance, graduation, academic proficiency, and student conduct as measured by rates of suspensions and expulsions. Sixty-four secondary…

  18. School Uniform Revisited: Procedure, Pressure and Equality

    Science.gov (United States)

    Carney, Damian; Sinclair, Adele

    2006-01-01

    The House of Lords' decision in "R. (on the application of Begum) v. The Headteacher and Governors of Denbigh High School" considered whether a particular school uniform policy infringed a student's right to manifest her religion under Article 9. This paper analyses the content of this decision, and explores how schools should approach…

  19. Mandatory School Uniforms and Freedom of Expression

    Science.gov (United States)

    Vopat, Mark C.

    2010-01-01

    On 10 December 2007 the Akron City School Board--following the precedent set by many school systems across the United States and the world--instituted a policy of mandatory school uniforms for all students in grades K-8. The measure was met with mixed reviews. While many parents supported the measure, a small group of parents from a selective,…

  20. Uniforms: Are They a Good Fit?

    Science.gov (United States)

    Boutelle, Marsha

    2008-01-01

    In an era where some parents seem unwilling or unable to draw the "clothes" line with their children, where pop culture influences kids' clothing choices as never before, and school safety--including gang violence--is at the top of everyone's minds, school uniforms and dress codes can play a significant role. What that role should be,…

  1. School Uniforms: A Blueprint for Legal Challenges.

    Science.gov (United States)

    Simonson, Mary Ellen

    1998-01-01

    This article discusses some of the options and strategies available to school districts in defending dress codes which mandate uniforms. Three components are essential to a successful defense: the dress code must bear a reasonable relation to the school's pedagogical purpose, it must include alternative avenues of expression, and it must…

  2. Uniformly convex and strictly convex Orlicz spaces

    Science.gov (United States)

    Masta, Al Azhary

    2016-02-01

    In this paper we define the new norm of Orlicz spaces on ℝn through a multiplication operator on an old Orlicz spaces. We obtain some necessary and sufficient conditions that the new norm to be a uniformly convex and strictly convex spaces.

  3. Stone stability under non-uniform flow

    NARCIS (Netherlands)

    Hoan, N.T.; Booij, R.; Hofland, B.; Stive, M.J.F.; Verhagen, H.J.

    2007-01-01

    The current research is aimed at finding a dimensionless stability parameter for non-uniform flow in which the effect of turbulence is incorporated. To this end, experiments were carried out in which both the bed response (quantified by a dimensionless entrainment rate) and the flow field (velocity

  4. MODERATOR ELEMENTS FOR UNIFORM POWER NUCLEAR REACTOR

    Science.gov (United States)

    Balent, R.

    1963-03-12

    This patent describes a method of obtaining a flatter flux and more uniform power generation across the core of a nuclear reactor. The method comprises using moderator elements having differing moderating strength. The elements have an increasing amount of the better moderating material as a function of radial and/or axial distance from the reactor core center. (AEC)

  5. Improving rooting uniformity in rose cuttings

    NARCIS (Netherlands)

    Telgen, van H.J.; Eveleens-Clark, B.A.; Garcia Victoria, N.

    2007-01-01

    Studies to improve rooting uniformity of single node stem cuttings for rose are reported. We found that the variation in shoot growth in a young rose crop depended on the variation in root number of the cuttings, which, in turn, was related to the auxin concentration applied to the cutting before ro

  6. Segmented blockcopolymers with uniform amide segments

    NARCIS (Netherlands)

    Husken, D.; Krijgsman, J.; Gaymans, R.J.

    2004-01-01

    Segmented blockcopolymers based on poly(tetramethylene oxide) (PTMO) soft segments and uniform crystallisable tetra-amide segments (TxTxT) are made via polycondensation. The PTMO soft segments, with a molecular weight of 1000 g/mol, are extended with terephthalic groups to a molecular weight of 6000

  7. Uniforms: Are They a Good Fit?

    Science.gov (United States)

    Boutelle, Marsha

    2008-01-01

    In an era where some parents seem unwilling or unable to draw the "clothes" line with their children, where pop culture influences kids' clothing choices as never before, and school safety--including gang violence--is at the top of everyone's minds, school uniforms and dress codes can play a significant role. What that role should be, however, is…

  8. Uniform color spaces and natural image statistics.

    Science.gov (United States)

    McDermott, Kyle C; Webster, Michael A

    2012-02-01

    Many aspects of visual coding have been successfully predicted by starting from the statistics of natural scenes and then asking how the stimulus could be efficiently represented. We started from the representation of color characterized by uniform color spaces, and then asked what type of color environment they implied. These spaces are designed to represent equal perceptual differences in color discrimination or appearance by equal distances in the space. The relative sensitivity to different axes within the space might therefore reflect the gamut of colors in natural scenes. To examine this, we projected perceptually uniform distributions within the Munsell, CIE L(*)u(*)v(*) or CIE L(*)a(*)b(*) spaces into cone-opponent space. All were elongated along a bluish-yellowish axis reflecting covarying signals along the L-M and S-(L+M) cardinal axes, a pattern typical (though not identical) to many natural environments. In turn, color distributions from environments were more uniform when projected into the CIE L(*)a(*)b(*) perceptual space than when represented in a normalized cone-opponent space. These analyses suggest the bluish-yellowish bias in environmental colors might be an important factor shaping chromatic sensitivity, and also suggest that perceptually uniform color metrics could be derived from natural scene statistics and potentially tailored to specific environments.

  9. Scheduling identical jobs on uniform parallel machines

    NARCIS (Netherlands)

    M. Dessouky (Mohamed); B. Lageweg (Ben); J.K. Lenstra; S.L. van de Velde (Steef)

    1990-01-01

    textabstractWe address the problem of scheduling n identical jobs on m uniform parallel machines to optimize scheduling criteria that are nondecreasing in the job completion times. It is well known that this can be formulated as a linear assignment problem, and subsequently solved in O(n3) time. We

  10. Towards a uniform analysis of 'any'

    NARCIS (Netherlands)

    van Rooij, R.

    2008-01-01

    In this paper, Universal any and Negative Polarity Item any are uniformly analyzed as ‘counterfactual’ donkey sentences (in disguise). Their difference in meaning is reduced here to the distinction between strong and weak readings of donkey sentences. It is shown that this explains the universal and

  11. Uniform spray coating for large tanks

    Science.gov (United States)

    Carter, J. M.

    1977-01-01

    System employs spray facility located within ventilated plastic booth to uniformly coat exterior of large cylindrical tanks with polyurethane foam insulation. Coating target is rotated on turntable while movable spray guns apply overlapping spirals of foam. Entire operation may be controlled by single operator from remote station.

  12. A NUMERICAL STUDY OF UNIFORM SUPERCONVERGENCE OF LDG METHOD FOR SOLVING SINGULARLY PERTURBED PROBLEMS

    Institute of Scientific and Technical Information of China (English)

    Ziqing Xie; Zuozheng Zhang; Zhimin Zhang

    2009-01-01

    In this paper,we consider the local discontinuous Galerkin method (LDG) for solving singularly perturbed convection-diffusion problems in one-and two-dimensional settings.The existence and uniqueness of the LDG solutions are verified.Numerical experiments demonstrate that it seems impossible to obtain uniform superconvergence for numerical fluxes under uniform meshes.Thanks to the implementation of two-type different anisotropic meshes,i.e.,the Shishkin and art improved grade meshes,the uniform 2p+1-order superconvergence is observed numerically for both one-dimensional and twodimensional cases.

  13. Energy feedback freeform lenses for uniform illumination of extended light source LEDs.

    Science.gov (United States)

    Li, Zongtao; Yu, Shudong; Lin, Liwei; Tang, Yong; Ding, Xinrui; Yuan, Wei; Yu, Binhai

    2016-12-20

    Using freeform lenses to construct uniform illumination systems is important in light-emitting diode (LED) devices. In this paper, the energy feedback design is used for freeform lens (EFFL) constructions by solving a set of partial differential equations that describe the mapping relationships between the source and the illumination pattern. The simulation results show that the method can overcome the illumination deviation caused by the extended light source (ELS) problem. Furthermore, a uniformity of 95.6% is obtained for chip-on-board (COB) compact LED devices. As such, prototype LEDs manufactured with the proposed freeform lenses demonstrate significant improvements in luminous efficiency and emission uniformity.

  14. Polarized Light Corridor Demonstrations.

    Science.gov (United States)

    Davies, G. R.

    1990-01-01

    Eleven demonstrations of light polarization are presented. Each includes a brief description of the apparatus and the effect demonstrated. Illustrated are strain patterns, reflection, scattering, the Faraday Effect, interference, double refraction, the polarizing microscope, and optical activity. (CW)

  15. Non-uniform impact excitation of a cylindrical bar

    Science.gov (United States)

    Karp, Baruch; Dorogoy, Avraham; Wang, Zonggang

    2009-06-01

    An experimental and numerical study of a non-uniform impact excitation of a circular bar is reported. In experiments, nine strikers with different contact area were accelerated against a circular bar. Axial surface strain of the impacted bar was measured at several distances from the impinged end to include the near and the far fields. The same experimental conditions were solved numerically using a commercial finite element code. It was demonstrated that the far-field response is insensitive to both the size and the form of the striker's colliding end. The distance at which such insensitivity is set is estimated to be approximately one and a half bar diameters.

  16. Demonstration of thermal control, microstructure control, defect mitigation and process parameter database generation for Ti-6Al-4V Direct Digital Manufacturing - Understanding defect mitigation and process parameter database generation for direct digital manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Dehoff, Ryan R [ORNL; Niyanth S, Niyanth [ORNL; Dinwiddie, Ralph Barton [ORNL; Robson, Alan [University of Tennessee (UT); Jordan, Brian H [ORNL; Chaudhary, Anil [Applied Optimization; Babu, Prof. Sudarsanam Suresh [University of Tennessee, Knoxville (UTK)

    2015-09-01

    Researchers from Manufacturing Demonstration Facility (MDF) at Oak Ridge National Laboratory (ORNL) worked with Applied Optimization (AO) to understand and evaluate the propensity for defect formation in builds manufactured using DM3D-POM laser direct metal deposition. The main aim of this collaboration was to understand the character of powder jet behavior as a function of the nozzle parameters such as cover gas, carrier gas, and shaping gas. In order to evaluate the sensitivities of the parameters used in model, various experiments were performed with in-situ monitoring of the powder stream characteristics using a high speed camera. A wide variety of conditions while keeping the hopper motor rpm constant, including laser power and travel speed were explored. The cross sections of the deposits were characterized using optical microscopy.

  17. The POSEIDON Demonstrator

    NARCIS (Netherlands)

    Laar, P.J.L.J. van de

    2013-01-01

    In this chapter, we discuss the Poseidon demonstrator: a demonstrator that integrates the individual research results of all partners of the Poseidon project. After describing how the Poseidon demonstrator was built, deployed, and operated, we will not only show many results obtained from the demons

  18. Overhead Projector Demonstrations.

    Science.gov (United States)

    Kolb, Doris, Ed.

    1988-01-01

    Details two demonstrations for use with an overhead projector in a chemistry lecture. Includes "A Very Rapidly Growing Silicate Crystal" and "A Colorful Demonstration to Simulate Orbital Hybridization." The materials and directions for each demonstration are included as well as a brief explanation of the essential learning involved. (CW)

  19. [Development of Fuzi precision decoction pieces (PDP) (I): Specification and quality uniformity].

    Science.gov (United States)

    Zhang, Ding-kun; Han, Xue; Zhou, Yong-feng; Tan, Peng; Yang, Ming; Peng, Cheng; Wang, Jia-bo; Xiao, Xiao-he

    2015-09-01

    The specification of decoction pieces and quality uniformity are the important factors to influence the efficacy of clinical medicine. Considering the deficiency of diversity, poor quality uniformity and confusion of decoction pieces specifications, we first propose a new idea of precision decoction pieces (PDP) based on clinical demands and fresh-processed technology. In order to explain the idea, a study case of aconite SUP is provided, including the optimized specification design, processing technology, extraction effects, quality uniformity, and toxic and efficacy variation and so on. The results showed that preparing 5 mm PDP by fresh-cutting is rather simple and practicable, with high efficiency and large yield; then, this technology could significantly decrease the ingredients loss and increase the efficacy components; moreover, it was helpful for achieving the quality uniformity and best extraction effects. This work revealed the quality superiority of PDP, and provided a good strategy and example for the standard of decoction pieces specification and modernization of processing technology.

  20. State-Space Based Approach to Particle Creation in Spatially Uniform Electric Fields

    CERN Document Server

    Dolby, C E; Dolby, Carl E.; Gull, Stephen F.

    2001-01-01

    Our formalism described recently in (Dolby et al, hep-th/0103228) is applied to the study of particle creation in spatially uniform electric fields, concentrating on the cases of a time-invariant electric field and a so-called `adiabatic' electric field. Several problems are resolved by incorporating the `Bogoliubov coefficient' approach and the `tunnelling' approaches into a single consistent, gauge invariant formulation. The value of a time-dependent particle interpretation is demonstrated by presenting a coherent account of the time-development of the particle creation process, in which the particles are created with small momentum (in the frame of the electric field) and are then accelerated by the electric field to make up the `bulge' of created particles predicted by asymptotic calculations. An initial state comprising one particle is also considered, and its evolution is described as being the sum of two contributions: the `sea of current' produced by the evolved vacuum, and the extra current arising f...