WorldWideScience

Sample records for delayed ultimate procedure

  1. ISP-27 OECD/NEA/CSNI International Standard Problem n.27. Bethsy experiment 9.1 B. 2. cold leg break without HPSI and with delayed ultimate procedure. Comparison report. Volume 1 + 2

    International Nuclear Information System (INIS)

    1992-11-01

    This report is the final comparison report for ISP-27, a blind problem which is based on the BETHSY test 9.1b performed in december 1989 at the Nuclear Research Center in Grenoble (France). The BETHSY integral test facility is a scaled down model of a 3 loop 900 e MW FRAMATOME PWR; the overall scaling factor applied to every volume, mass flowrate and power level is close to 1/100, while elevations are 1/1 in order to preserve the gravitational heads. The cold leg break is combined with the High Pressure Injection System (HPIS) failure. In that case, the state oriented approach requires operators to start an Ultimate Procedure, which consists in fully opening the Steam Generator (SG) atmospheric dumps as soon as they are informed of the unavailability of the HPIS. The presently studied scenario assumes a delayed application of this procedure, which is started only when the core outlet temperature rises significantly higher than the saturation temperature. The BETHSY Test 9.1b addresses, besides typical problems relevant to Small Break Loss Of Coolant Accidents (SBLOCA) such as critical 2-phase flow, loop seal clearing, heat-transfer during boil-off or accumulator injection, specific aspects related to the fast depressurization (primary to secondary and structural heat transfer), uncovered core behavior when intense condensation takes place in the SG, and primary side refilling by the Low Pressure Injection System (LPIS)

  2. Ulnar artery: The Ulysses ultimate resort for coronary procedures

    Directory of Open Access Journals (Sweden)

    George Hahalis, MD, PhD

    2016-07-01

    Full Text Available Despite the increasing worldwide adoption of the transradial access site, the ulnar artery (UA only very infrequently serves as a primary option for coronary procedures. In contrast to the uncertainty surrounding previous reports regarding the feasibility and safety, recent data from larger registries and randomized trials provide more conclusive evidence that the transulnar route may be safely selected as an alternative arterial access approach. However, a default transulnar strategy appears time-consuming and is associated with higher crossover rates compared with the radial artery (RA. Once arterial access is obtained, the likelihood of a successful coronary procedure is high and similar between the two forearm arteries. The UA has similar flow-mediating vasodilating properties with and seems at least as vulnerable as the RA with regard to incident occlusion, with UA occlusion (UAO rates being probably higher than previously anticipated. A learning curve effect may not be apparent for crossover rates among experienced radialists, but increasing experience is associated with reduction in the fluoroscopy time, contrast volume and frequency of large hematoma formation. The UA may represents an important alternative access site for coronary procedures, and experienced radial operators should obtain additional skills to perform the transulnar approach. Nevertheless, in view of this method's lower feasibility compared to the RA, an initial ulnar access strategy should be reserved for carefully selected patients to ensure satisfactory cannulation rates.

  3. Ulnar artery: The Ulysses ultimate resort for coronary procedures.

    Science.gov (United States)

    Hahalis, George; Deftereos, Spyridon; Bertrand, Olivier F

    2016-08-20

    Despite the increasing worldwide adoption of the transradial access site, the ulnar artery (UA) only very infrequently serves as a primary option for coronary procedures. In contrast to the uncertainty surrounding previous reports regarding the feasibility and safety, recent data from larger registries and randomized trials provide more conclusive evidence that the transulnar route may be safely selected as an alternative arterial access approach. However, a default transulnar strategy appears time-consuming and is associated with higher crossover rates compared with the radial artery (RA). Once arterial access is obtained, the likelihood of a successful coronary procedure is high and similar between the two forearm arteries. The UA has similar flow-mediating vasodilating properties with and seems at least as vulnerable as the RA with regard to incident occlusion, with UA occlusion (UAO) rates being probably higher than previously anticipated. A learning curve effect may not be apparent for crossover rates among experienced radialists, but increasing experience is associated with reduction in the fluoroscopy time, contrast volume and frequency of large hematoma formation. The UA may represents an important alternative access site for coronary procedures, and experienced radial operators should obtain additional skills to perform the transulnar approach. Nevertheless, in view of this method's lower feasibility compared to the RA, an initial ulnar access strategy should be reserved for carefully selected patients to ensure satisfactory cannulation rates. Copyright © 2016 Hellenic Cardiological Society. Published by Elsevier B.V. All rights reserved.

  4. PSA Update Procedures, an Ultimate Need for Living PSA

    International Nuclear Information System (INIS)

    Hegedus, D.

    1998-01-01

    Nuclear facilities by their complex nature, change with time. These changes can be both physical (plant modification, etc.), operational (enhanced procedures, etc.) and organizational. In addition, there are also changes in our understanding of the plant, due to operational experience, data collection, technology enhancements, etc. Therefore, it is imperative that PSA model must be frequently up-dated or modified to reflect these changes. Over the last ten years. these has been a remarkable growth of the use of Probabilistic Safety Assessments (PSAs). The most rapidly growing area of the PSA Applications is their use to support operational decision-making. Many of these applications are characterized by the potential for not only improving the safety level but also for providing guidance on the optimal use of resources and reducing regulatory burden. To enable a wider use of the PSA model as a tool for safety activities it is essential to maintain the model in a controlled state. Moreover, to fulfill requirements for L iving PSA , the PSA model has to be constantly updated and/or monitored to reflect the current plant configuration. It should be noted that the PSA model should not only represent the plant design but should also represent the operational and emergency procedures. To keep the PSA model up-to-date several issues should be clearly defined including: - Responsibility should be divided among the PSA group, - Procedures for implementing changes should be established, and - QA requirements/program should be established to assure documentation and reporting. (author)

  5. Human performance evaluation: The procedures of ultimate response guideline for nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Kang-Hung, E-mail: alvinks@iner.gov.tw [Institute of Nuclear Energy Research, Atomic Engery Council, No. 1000, Whenhua Road, Jiaan Village, Longtan Township, Taoyuan County, Taiwan (China); Hwang, Sheue-Ling, E-mail: slhwang@ie.nthu.edu.tw [Department of Industrial Engineering and Engineering Management, National Tsing Hua University, No. 101, Section 2, Kuang-Fu Road, Hsinchu, Taiwan 30013, Taiwan (China)

    2014-07-01

    Highlights: • This study adopts SPAR-H to evaluate HEPs in the URG procedures. • The involvement of URG procedures could reduce CDF significantly. • Upgrading the training level of staff will enhance the reliability effectively. • Aiding the plant manager in making URG decision will enhance the reliability. - Abstract: In the nuclear accident which occurred in Japan on March 11, 2011, several units of Fukushima conventional BWR experienced a total loss of power and water supply triggered by a heavy earthquake and subsequent Tsunami which were outside design models. In the past, when an accident occurred, operators in nuclear power plants (NPP) followed emergency operating procedures (EOPs) or severe accident management guidance (SAMG). However, EOP and SAMG are symptom-based procedures to cope with severe transients and accidents, depending on real-time operational parameters. Ultimate response guidelines (URG), a plant specific interim remedy action plan, was developed to manage accidents caused by compound disasters which exceed design models. The URG guides the plant operators’ conduct of reactor depressurization, core cooling water injection, and containment venting. This study adopts NUREG/CR-6883 (Standardized Plant Analysis Risk Human Reliability Analysis, SPAR-H) to evaluate human error probabilities (HEPs) of action and diagnosis in the current URG procedures. We found the human reliability of URG procedures analyzed by SPAR-H is about 85% (depending on different decision makers). Upgrading the training level of staff or enhancing plant managers ability to decide whether to execute URG will enhance the human reliability of URG procedures.

  6. The impact of therapeutic delay time on acute scintigraphic lesion and ultimate scar formation in children with first febrile UTI.

    Science.gov (United States)

    Oh, Mi Mi; Kim, Jin Wook; Park, Min Gu; Kim, Je Jong; Yoo, Kee Hwan; Moon, Du Geon

    2012-03-01

    We assessed the role of therapeutic delay time (TDT) in acute renal cortical scintigraphic lesion (ASL) and ultimate scar formation (USF) in children with first febrile UTI and whether it is affected by the presence of vesico-ureteral reflux (VUR). 230 children, 90 girls and 140 boys with first febrile UTI were included. Radiologic (USG, DMSA, and VCUG), clinical (age, gender, peak fever, therapeutic delay time) and laboratory (CBC with differential count, ANC (absolute neutrophil count), BUN, Creatinine, urine analysis, gram stain, culture, CRP and ESR) variables were analysed. DMSA was performed within 5 days and after six months. VCUG was performed after acute phase of UTI. The differences in TDT according to the presence of ASL, USF and VUR were assessed. And the correlation between ASL or USF with the duration of TDT was assessed. Of 230 patients enrolled, 142 patients had refluxing UTI and 88 patients had non-refluxing UTI. TDT was the risk factor associated with ASL and USF along with presence of VUR. TDT was longer in ASL positive group compared with the ASL negative group. Also USF group showed longer TDT compared with those without USF in both refluxing UTI and non refluxing UTI. The TDT was significantly shorter in USF group with the presence of VUR. Positive linear association was noted between prevalence of ASL and USF and duration of TDT. In conclusion, the impact of UTI on formation of USF may be enhanced by the presence of VUR with shorter duration of TDT.

  7. Sentinel node biopsy (SNB) in malignant melanoma as same day procedure vs delayed procedure

    DEFF Research Database (Denmark)

    Rødgaard, Jes Christian; Kramer, Stine; Stolle, Lars B

    2013-01-01

    The aim of this study was to compare a delayed sentinel node biopsy (dSNB) procedure with a same-day procedure (sSNB) in malignant melanoma. In March 2012, Aarhus University Hospital went from the dSNB to the sSNB procedure defined by lymphoscintigraphy (LS) and sentinel node biopsy (SNB) perform......, essential to keep the morbidity and economic costs low, while keeping the quality of the procedure high....

  8. Efficiency of performing pulmonary procedures in a shared endoscopy unit: procedure time, turnaround time, delays, and procedure waiting time.

    Science.gov (United States)

    Verma, Akash; Lee, Mui Yok; Wang, Chunhong; Hussein, Nurmalah B M; Selvi, Kalai; Tee, Augustine

    2014-04-01

    The purpose of this study was to assess the efficiency of performing pulmonary procedures in the endoscopy unit in a large teaching hospital. A prospective study from May 20 to July 19, 2013, was designed. The main outcome measures were procedure delays and their reasons, duration of procedural steps starting from patient's arrival to endoscopy unit, turnaround time, total case durations, and procedure wait time. A total of 65 procedures were observed. The most common procedure was BAL (61%) followed by TBLB (31%). Overall procedures for 35 (53.8%) of 65 patients were delayed by ≥ 30 minutes, 21/35 (60%) because of "spillover" of the gastrointestinal and surgical cases into the time block of pulmonary procedure. Time elapsed between end of pulmonary procedure and start of the next procedure was ≥ 30 minutes in 8/51 (16%) of cases. In 18/51 (35%) patients there was no next case in the room after completion of the pulmonary procedure. The average idle time of the room after the end of pulmonary procedure and start of next case or end of shift at 5:00 PM if no next case was 58 ± 53 minutes. In 17/51 (33%) patients the room's idle time was >60 minutes. A total of 52.3% of patients had the wait time >2 days and 11% had it ≥ 6 days, reason in 15/21 (71%) being unavailability of the slot. Most pulmonary procedures were delayed due to spillover of the gastrointestinal and surgical cases into the block time allocated to pulmonary procedures. The most common reason for difficulty encountered in scheduling the pulmonary procedure was slot unavailability. This caused increased procedure waiting time. The strategies to reduce procedure delays and turnaround times, along with improved scheduling methods, may have a favorable impact on the volume of procedures performed in the unit thereby optimizing the existing resources.

  9. Two planar polishing methods by using FIB technique: Toward ultimate top-down delayering for failure analysis

    Energy Technology Data Exchange (ETDEWEB)

    Wang, D. D., E-mail: dandan.wang@globalfoundries.com; Huang, Y. M.; Tan, P. K.; Feng, H.; Low, G. R.; Yap, H. H.; He, R.; Tan, H.; Dawood, M. K.; Zhao, Y. Z.; Lam, J.; Mai, Z. H. [GLOBALFOUNDRIES Singapore Pte. Ltd, 60 Woodlands Industrial Park D Street 2, Singapore 738406 (Singapore)

    2015-12-15

    Presently two major limiting factors are hindering the failure analysis (FA) development during the semiconductor manufacturing process and technology improvement: (1) Impossibility of manual polishing on the edge dies due to the amenability of layer peeling off; (2) Abundant demand of multi-locations FA, especially focusing different levels of layers simultaneously. Aiming at resolving these limitations, here we demonstrate two unique high precision polishing methods by using focused ion beam (FIB) technique. One is the vertical top down chemical etching at the aimed location; the other one is the planar top down slicing. Using the FIB for delayering not only solves these problems mentioned above, but also offers significant advantages over physical planar polishing methods such as: (1) having a better control of the delayering progress, (2) enabling precisely milling at a region of interest, (3) providing the prevention of over-delayering and (4) possessing capability to capture images at the region of interest simultaneously and cut into the die directly to expose the exact failure without damaging other sections of the specimen.

  10. Procedure for calculating estimated ultimate recoveries of Bakken and Three Forks Formations horizontal wells in the Williston Basin

    Science.gov (United States)

    Cook, Troy A.

    2013-01-01

    Estimated ultimate recoveries (EURs) are a key component in determining productivity of wells in continuous-type oil and gas reservoirs. EURs form the foundation of a well-performance-based assessment methodology initially developed by the U.S. Geological Survey (USGS; Schmoker, 1999). This methodology was formally reviewed by the American Association of Petroleum Geologists Committee on Resource Evaluation (Curtis and others, 2001). The EUR estimation methodology described in this paper was used in the 2013 USGS assessment of continuous oil resources in the Bakken and Three Forks Formations and incorporates uncertainties that would not normally be included in a basic decline-curve calculation. These uncertainties relate to (1) the mean time before failure of the entire well-production system (excluding economics), (2) the uncertainty of when (and if) a stable hyperbolic-decline profile is revealed in the production data, (3) the particular formation involved, (4) relations between initial production rates and a stable hyperbolic-decline profile, and (5) the final behavior of the decline extrapolation as production becomes more dependent on matrix storage.

  11. Claims Procedure for Plans Providing Disability Benefits; 90-Day Delay of Applicability Date. Final rule; delay of applicability

    Science.gov (United States)

    2017-11-29

    This document delays for ninety (90) days--through April 1, 2018--the applicability of a final rule amending the claims procedure requirements applicable to ERISA-covered employee benefit plans that provide disability benefits (Final Rule). The Final Rule was published in the Federal Register on December 19, 2016, became effective on January 18, 2017, and was scheduled to become applicable on January 1, 2018. The delay announced in this document is necessary to enable the Department of Labor to carefully consider comments and data as part of its effort, pursuant to Executive Order 13777, to examine regulatory alternatives that meet its objectives of ensuring the full and fair review of disability benefit claims while not imposing unnecessary costs and adverse consequences.

  12. A comparison of pecking generated by serial, delay, and trace autoshaping procedures1

    Science.gov (United States)

    Newlin, Robert J.; LoLordo, Vincent M.

    1976-01-01

    Pigeons were exposed to serial, delay, and trace autoshaping procedures. In Experiment I, all conditioned stimuli (CSs) were changes in illumination of the response key. The number of trials to acquisition of the keypeck increased from serial, to 4-sec delay, 8-sec delay, and 8-sec trace procedures, in that order. In Experiment II, which used a longer intertrial interval, trials to criterion increased from 8-sec delay, to 28-sec delay, 8-sec trace, and 28-sec trace procedures, in that order. In Experiment III, two groups received serial procedures in which the first CS was either a tone or a houselight, and the second was a keylight. The tone group acquired the key peck more rapidly than the houselight group. Early in conditioning in these experiments, and when the conditioned stimulus was a change in the keylight, there was a short latency to the onset of pecking and pecking was directed at the CS. After extensive conditioning, or when the CS was relatively diffuse, pecking still occurred, but had a longer latency and was not reliably directed toward the conditioned stimulus. PMID:16811907

  13. Using a Constant Time Delay Procedure to Teach Foundational Swimming Skills to Children with Autism

    Science.gov (United States)

    Rogers, Laura; Hemmeter, Mary Louise; Wolery, Mark

    2010-01-01

    The purpose of this study was to evaluate the effectiveness of using a constant time delay procedure to teach foundational swimming skills to three children with autism. The skills included flutter kick, front-crawl arm strokes, and head turns to the side. A multiple-probe design across behaviors and replicated across participants was used.…

  14. Facilitating relational framing in children and individuals with developmental delay using the relational completion procedure.

    Science.gov (United States)

    Walsh, Sinead; Horgan, Jennifer; May, Richard J; Dymond, Simon; Whelan, Robert

    2014-01-01

    The Relational Completion Procedure is effective for establishing same, opposite and comparative derived relations in verbally able adults, but to date it has not been used to establish relational frames in young children or those with developmental delay. In Experiment 1, the Relational Completion Procedure was used with the goal of establishing two 3-member sameness networks in nine individuals with Autism Spectrum Disorder (eight with language delay). A multiple exemplar intervention was employed to facilitate derived relational responding when required. Seven of nine participants in Experiment 1 passed tests for derived relations. In Experiment 2, eight participants (all of whom, except one, had a verbal repertoire) were given training with the aim of establishing two 4-member sameness networks. Three of these participants were typically developing young children aged between 5 and 6 years old, all of whom demonstrated derived relations, as did four of the five participants with developmental delay. These data demonstrate that it is possible to reliably establish derived relations in young children and those with developmental delay using an automated procedure. © Society for the Experimental Analysis of Behavior.

  15. An adaptive, individualized fMRI delay discounting procedure to increase flexibility and optimize scanner time.

    Science.gov (United States)

    Koffarnus, Mikhail N; Deshpande, Harshawardhan U; Lisinski, Jonathan M; Eklund, Anders; Bickel, Warren K; LaConte, Stephen M

    2017-11-01

    Research on the rate at which people discount the value of future rewards has become increasingly prevalent as discount rate has been shown to be associated with many unhealthy patterns of behavior such as drug abuse, gambling, and overeating. fMRI research points to a fronto-parietal-limbic pathway that is active during decisions between smaller amounts of money now and larger amounts available after a delay. Researchers in this area have used different variants of delay discounting tasks and reported various contrasts between choice trials of different types from these tasks. For instance, researchers have compared 1) choices of delayed monetary amounts to choices of the immediate monetary amounts, 2) 'hard' choices made near one's point of indifference to 'easy' choices that require little thought, and 3) trials where an immediate choice is available versus trials where one is unavailable, regardless of actual eventual choice. These differences in procedure and analysis make comparison of results across studies difficult. In the present experiment, we designed a delay discounting task with the intended capability of being able to construct contrasts of all three comparisons listed above while optimizing scanning time to reduce costs and avoid participant fatigue. This was accomplished with an algorithm that customized the choice trials presented to each participant with the goal of equalizing choice trials of each type. We compared this task, which we refer to here as the individualized discounting task (IDT), to two other delay discounting tasks previously reported in the literature (McClure et al., 2004; Amlung et al., 2014) in 18 participants. Results show that the IDT can examine each of the three contrasts mentioned above, while yielding a similar degree of activation as the reference tasks. This suggests that this new task could be used in delay discounting fMRI studies to allow researchers to more easily compare their results to a majority of previous

  16. The effects of local nitroglycerin on the surgical delay procedure in prefabricated flaps by vascular implant in rats.

    Science.gov (United States)

    Sá, Jairo Zacchê de; Aguiar, José Lamartine de Andrade; Cruz, Adriana Ferreira; Schuler, Alexandre Ricardo Pereira; Lima, José Ricardo Alves de; Marques, Olga Martins

    2012-12-01

    To evaluate the effect of local nitroglycerin on the viable area of a prefabricated flap for vascular implant in rats, and to investigate the surgical delay procedure. A femoral pedicle was implanted under the skin of the abdominal wall in forty Wistar rats. The animals were divided into four groups of ten: group 1 - without surgical delay procedure and local nitroglycerin; group 2 - with surgical delay procedure, but without local nitroglycerin; group 3 - without surgical delay procedure, but with local nitroglycerin; and group 4 - with simultaneous surgical delay procedure and local nitroglycerin. The percentages of the viable areas, in relation to the total flap, were calculated using AutoCAD R 14. The mean percentage value of the viable area was 8.9% in the group 1. 49.4% in the group 2; 8.4% in the group 3 and 1.1% in the group 4. There was significant difference between groups 1 and 2 (p=0.005), 1 and 4 (p=0.024), 2 and 3 (p=0.003), 2 and 4 (p=0.001). These results support the hypothesis that the closure of the arterial venous channels is responsible for the phenomenon of surgical delay procedure. Local nitroglycerin did not cause an increase in the prefabricated viable flap area by vascular implantation and decreased the viable flap area that underwent delay procedures.

  17. Estimating the subjective value of future rewards: comparison of adjusting-amount and adjusting-delay procedures.

    Science.gov (United States)

    Holt, Daniel D; Green, Leonard; Myerson, Joel

    2012-07-01

    The present study examined whether equivalent discounting of delayed rewards is observed with different experimental procedures. If the underlying decision-making process is the same, then similar patterns of results should be observed regardless of procedure, and similar estimates of the subjective value of future rewards (i.e., indifference points) should be obtained. Two experiments compared discounting on three types of procedure: adjusting-delay (AD), adjusting-immediate-amount (AIA), and adjusting-delayed-amount (ADA). For the two procedures for which discounting functions can be established (i.e., AD and AIA), a hyperboloid provided good fits to the data at both the group and individual levels, and individuals' discounting on one procedure tended to be correlated with their discounting on the other. Notably, the AIA procedure produced the more consistent estimates of the degree of discounting, and in particular, discounting on the AIA procedure was unaffected by the order in which choices were presented. Regardless of which of the three procedures was used, however, similar patterns of results were obtained: Participants systematically discounted the value of delayed rewards, and robust magnitude effects were observed. Although each procedure may have its own advantages and disadvantages, use of all three types of procedure in the present study provided converging evidence for common decision-making processes underlying the discounting of delayed rewards. Copyright © 2012 Elsevier B.V. All rights reserved.

  18. Comparison of intraoperative versus delayed enteral feeding tube placement in patients undergoing a Whipple procedure.

    Science.gov (United States)

    Scaife, Courtney L; Hewitt, Kelly C; Mone, Mary C; Hansen, Heidi J; Nelson, Edward T; Mulvihill, Sean J

    2014-01-01

    The intraoperative placement of an enteral feeding tube (FT) during pancreaticoduodenectomy (PD) is based on the surgeon's perception of need for postoperative nutrition. Published preoperative risk factors predicting postoperative morbidity may be used to predict FT need and associated intraoperative placement. A retrospective review of patients who underwent PD during 2005-2011 was performed by querying the National Surgical Quality Improvement Program (NSQIP) database with specific procedure codes. Patients were categorized based on how many of 10 possible preoperative risk factors they demonstrated. Groups of patients with scores of ≤ 1 (low) and ≥ 2 (high), respectively, were compared for FT need, length of stay (LoS) and organ space surgical site infections (SSIs). Of 138 PD patients, 82 did not have an FT placed intraoperatively, and, of those, 16 (19.5%) required delayed FT placement. High-risk patients were more likely to require a delayed FT (29.3%) compared with low-risk patients (9.8%) (P = 0.026). The 16 patients who required a delayed FT had a median LoS of 15.5 days, whereas the 66 patients who did not require an FT had a median LoS of 8 days (P < 0.001). In this analysis, subjects considered as high-risk patients were more likely to require an FT than low-risk patients. Assessment of preoperative risk factors may improve decision making for selective intraoperative FT placement. © 2013 International Hepato-Pancreato-Biliary Association.

  19. Flux scaling: Ultimate regime

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Flux scaling: Ultimate regime. With the Nusselt number and the mixing length scales, we get the Nusselt number and Reynolds number (w'd/ν) scalings: and or. and. scaling expected to occur at extremely high Ra Rayleigh-Benard convection. Get the ultimate regime ...

  20. Procedure for calculating estimated ultimate recoveries of wells in the Mississippian Barnett Shale, Bend Arch–Fort Worth Basin Province of north-central Texas

    Science.gov (United States)

    Leathers-Miller, Heidi M.

    2017-11-28

    In 2015, the U.S. Geological Survey published an assessment of technically recoverable continuous oil and gas resources of the Mississippian Barnett Shale in the Bend Arch–Fort Worth Basin Province of north-central Texas. Of the two assessment units involved in the overall assessment, one included a roughly equal number of oil wells and gas wells as classified by the U.S. Geological Survey’s standard of gas wells having production greater than or equal to 20,000 cubic feet of gas per barrel of oil and oil wells having production less than 20,000 cubic feet of gas per barrel of oil. As a result, estimated ultimate recoveries (EURs) were calculated for both oil wells and gas wells in one of the assessment units. Generally, only gas EURs or only oil EURs are calculated for an assessment unit. These EURs were calculated with data from IHS MarkitTM using DeclinePlus software in the Harmony interface and were a major component of the quantitative resource assessment. The calculated mean EURs ranged from 235 to 2,078 million cubic feet of gas and 21 to 39 thousand barrels of oil for various subsets of wells.

  1. Teaching Generalized Reading of Product Warning Labels to Young Adults with Autism Using the Constant Time Delay Procedure

    Science.gov (United States)

    Dogoe, Maud S.; Banda, Devender R.; Lock, Robin H.; Feinstein, Rita

    2011-01-01

    This study examined the effectiveness of the constant timed delay procedure for teaching two young adults with autism to read, define, and state the contextual meaning of keywords on product warning labels of common household products. Training sessions were conducted in the dyad format using flash cards. Results indicated that both participants…

  2. Single-subject withdrawal designs in delayed matching-to-sample procedures

    OpenAIRE

    Eilifsen, Christoffer; Arntzen, Erik

    2011-01-01

    In most studies of delayed matching-to-sample (DMTS) and stimulus equivalence, the delay has remained fixed throughout a single experimental condition. We wanted to expand on the DMTS and stimulus equivalence literature by examining the effects of using titrating delays with different starting points during the establishment of conditional discriminations prerequisite for stimulus equivalence. In Experiment 1, a variation of a single-subject withdrawal design was used. Ten adults were exposed...

  3. Using Video to Bridge the Gap Between Problem Behavior and a Delayed Time-out Procedure.

    Science.gov (United States)

    Coppage, Sara; Meindl, James N

    2017-09-01

    Treatment plans focused on problem behavior often include punishment contingencies to decrease problem behavior. Immediate punishers are typically more effective than delayed punishers, but immediate delivery of a punisher is not always possible. Strategies need to be developed to increase the suppressive effects of delayed punishers. This study demonstrated the effectiveness of a treatment package involving replaying a video recording of problem behavior immediately before delivering a 15 min delayed time-out. This treatment package may prove to be an accessible and inexpensive strategy when using delayed punishers.

  4. Stalking the ultimate particle

    CERN Multimedia

    2003-01-01

    If you missed the ARTE programme entitled "L'Ultime Particule" broadcast in February, you have another chance to catch it in CERN's Main Auditorium on 13 March. "L'Ultime Particule" is a documentary by the French director Michel Andrieu that seeks to explain particle physics through a contemplative quest for the research physicists of matter of today and yesteryear. Invariably kitted out in a red parka and a soft hat, the programme's investigator scours the planet and the archives in search of the research physicists who are stalking the ultimate particle, the Higgs boson, in their quest to understand the structure of matter. Naturally enough, CERN is an important stage of his journey where Michel Andrieu and his team spent several days last year. Both from the physics and metaphysical points of view, "L'Ultime Particule" is worth seeing. The film's director, Michel Andrieu, will introduce his documentary and answer questions from the audience after the documentary has been shown. L'Ultime Particule by Mic...

  5. The influence of procedure delay on resource use: a national study of patients with open tibial fracture.

    Science.gov (United States)

    Sears, Erika Davis; Burke, James F; Davis, Matthew M; Chung, Kevin C

    2013-03-01

    The purpose of this study was to (1) understand national variation in delay of emergency procedures in patients with open tibial fracture at the hospital level and (2) compare length of stay and cost in patients cared for at the best- and worst-performing hospitals for delay. The authors retrospectively analyzed the 2003 to 2009 Nationwide Inpatient Sample. Adult patients with open tibial fracture were included. Hospital probability of delay in performing emergency procedures beyond the day of admission was calculated. Multilevel linear regression random-effects models were created to evaluate the relationship between the treating hospital's tendency for delay (in quartiles) and the log-transformed outcomes of length of stay and cost. The final sample included 7029 patients from 332 hospitals. Patients treated at hospitals in the fourth (worst) quartile for delay were estimated to have 12 percent (95 percent CI, 2 to 21 percent) higher cost compared with patients treated at hospitals in the first quartile. In addition, patients treated at hospitals in the fourth quartile had an estimated 11 percent (95 percent CI, 4 to 17 percent) longer length of stay compared with patients treated at hospitals in the first quartile. Patients with open tibial fracture treated at hospitals with more timely initiation of surgical care had lower cost and shorter length of stay than patients treated at hospitals with less timely initiation of care. Policies directed toward mitigating variation in care may reduce unnecessary waste.

  6. Treatment of displaced talar neck fractures using delayed procedures of plate fixation through dual approaches.

    Science.gov (United States)

    Xue, Youdi; Zhang, Hui; Pei, Fuxing; Tu, Chongqi; Song, Yueming; Fang, Yue; Liu, Lei

    2014-01-01

    Treatment of talar neck fractures is challenging. Various surgical approaches and fixation methods have been documented. Clinical outcomes are often dissatisfying due to inadequate reduction and fixation with high rates of complications. Obtaining satisfactory clinical outcomes with minimum complications remains a hard task for orthopaedic surgeons. In the period from May 2007 to September 2010, a total of 31 cases with closed displaced talar neck fractures were treated surgically in our department. Injuries were classified according to the Hawkins classification modified by Canale and Kelly. Under general anaesthesia with sufficient muscle relaxation, urgent closed reduction was initiated once the patients were admitted; if the procedure failed, open reduction and provisional stabilisation with Kirschner wires through an anteromedial approach with tibiometatarsal external fixation were performed. When the soft tissue had recovered, definitive fixation was performed with plate and screws through dual approaches. The final follow-up examination included radiological analysis, clinical evaluation and functional outcomes which were carried out according to the Ankle-Hindfoot Scale of the American Orthopaedic Foot and Ankle Society (AOFAS), patient satisfaction and SF-36. Twenty-eight patients were followed up for an average of 25 months (range 18-50 months) after the injury. Only two patients had soft tissue complications, and recovery was satisfactory with conservative treatment. All of the fractures healed anatomically without malunion and nonunion, and the average union time was 14 weeks (range 12-24 weeks). Post-traumatic arthritis developed in ten cases, while six patients suffered from avascular necrosis of the talus. Secondary procedures included three cases of subtalar arthrodesis, one case of ankle arthrodesis and one case of total ankle replacement. The mean AOFAS hindfoot score was 78 (range 65-91). According to the SF-36, the average score of the

  7. The ultimate quotable Einstein

    CERN Document Server

    2011-01-01

    Here is the definitive new edition of the hugely popular collection of Einstein quotations that has sold tens of thousands of copies worldwide and been translated into twenty-five languages. The Ultimate Quotable Einstein features 400 additional quotes, bringing the total to roughly 1,600 in all. This ultimate edition includes new sections--"On and to Children," "On Race and Prejudice," and "Einstein's Verses: A Small Selection"--as well as a chronology of Einstein's life and accomplishments, Freeman Dyson's authoritative foreword, and new commentary by Alice Calaprice.

  8. Using Video to Bridge the Gap Between Problem Behavior and a Delayed Time-out Procedure

    OpenAIRE

    Coppage, Sara; Meindl, James N.

    2017-01-01

    Treatment plans focused on problem behavior often include punishment contingencies to decrease problem behavior. Immediate punishers are typically more effective than delayed punishers, but immediate delivery of a punisher is not always possible. Strategies need to be developed to increase the suppressive effects of delayed punishers. This study demonstrated the effectiveness of a treatment package involving replaying a video recording of problem behavior immediately before delivering a 15 mi...

  9. A TOTP-Based Enhanced Route Optimization Procedure for Mobile IPv6 to Reduce Handover Delay and Signalling Overhead

    Science.gov (United States)

    Shah, Peer Azmat; Hasbullah, Halabi B.; Lawal, Ibrahim A.; Aminu Mu'azu, Abubakar; Tang Jung, Low

    2014-01-01

    Due to the proliferation of handheld mobile devices, multimedia applications like Voice over IP (VoIP), video conferencing, network music, and online gaming are gaining popularity in recent years. These applications are well known to be delay sensitive and resource demanding. The mobility of mobile devices, running these applications, across different networks causes delay and service disruption. Mobile IPv6 was proposed to provide mobility support to IPv6-based mobile nodes for continuous communication when they roam across different networks. However, the Route Optimization procedure in Mobile IPv6 involves the verification of mobile node's reachability at the home address and at the care-of address (home test and care-of test) that results in higher handover delays and signalling overhead. This paper presents an enhanced procedure, time-based one-time password Route Optimization (TOTP-RO), for Mobile IPv6 Route Optimization that uses the concepts of shared secret Token, time based one-time password (TOTP) along with verification of the mobile node via direct communication and maintaining the status of correspondent node's compatibility. The TOTP-RO was implemented in network simulator (NS-2) and an analytical analysis was also made. Analysis showed that TOTP-RO has lower handover delays, packet loss, and signalling overhead with an increased level of security as compared to the standard Mobile IPv6's Return-Routability-based Route Optimization (RR-RO). PMID:24688398

  10. A TOTP-Based Enhanced Route Optimization Procedure for Mobile IPv6 to Reduce Handover Delay and Signalling Overhead

    Directory of Open Access Journals (Sweden)

    Peer Azmat Shah

    2014-01-01

    Full Text Available Due to the proliferation of handheld mobile devices, multimedia applications like Voice over IP (VoIP, video conferencing, network music, and online gaming are gaining popularity in recent years. These applications are well known to be delay sensitive and resource demanding. The mobility of mobile devices, running these applications, across different networks causes delay and service disruption. Mobile IPv6 was proposed to provide mobility support to IPv6-based mobile nodes for continuous communication when they roam across different networks. However, the Route Optimization procedure in Mobile IPv6 involves the verification of mobile node’s reachability at the home address and at the care-of address (home test and care-of test that results in higher handover delays and signalling overhead. This paper presents an enhanced procedure, time-based one-time password Route Optimization (TOTP-RO, for Mobile IPv6 Route Optimization that uses the concepts of shared secret Token, time based one-time password (TOTP along with verification of the mobile node via direct communication and maintaining the status of correspondent node’s compatibility. The TOTP-RO was implemented in network simulator (NS-2 and an analytical analysis was also made. Analysis showed that TOTP-RO has lower handover delays, packet loss, and signalling overhead with an increased level of security as compared to the standard Mobile IPv6’s Return-Routability-based Route Optimization (RR-RO.

  11. A TOTP-based enhanced route optimization procedure for mobile IPv6 to reduce handover delay and signalling overhead.

    Science.gov (United States)

    Shah, Peer Azmat; Hasbullah, Halabi B; Lawal, Ibrahim A; Aminu Mu'azu, Abubakar; Tang Jung, Low

    2014-01-01

    Due to the proliferation of handheld mobile devices, multimedia applications like Voice over IP (VoIP), video conferencing, network music, and online gaming are gaining popularity in recent years. These applications are well known to be delay sensitive and resource demanding. The mobility of mobile devices, running these applications, across different networks causes delay and service disruption. Mobile IPv6 was proposed to provide mobility support to IPv6-based mobile nodes for continuous communication when they roam across different networks. However, the Route Optimization procedure in Mobile IPv6 involves the verification of mobile node's reachability at the home address and at the care-of address (home test and care-of test) that results in higher handover delays and signalling overhead. This paper presents an enhanced procedure, time-based one-time password Route Optimization (TOTP-RO), for Mobile IPv6 Route Optimization that uses the concepts of shared secret Token, time based one-time password (TOTP) along with verification of the mobile node via direct communication and maintaining the status of correspondent node's compatibility. The TOTP-RO was implemented in network simulator (NS-2) and an analytical analysis was also made. Analysis showed that TOTP-RO has lower handover delays, packet loss, and signalling overhead with an increased level of security as compared to the standard Mobile IPv6's Return-Routability-based Route Optimization (RR-RO).

  12. Ethanol induces impulsive-like responding in a delay-of-reward operant choice procedure: impulsivity predicts autoshaping.

    Science.gov (United States)

    Tomie, A; Aguado, A S; Pohorecky, L A; Benjamin, D

    1998-10-01

    Autoshaping conditioned responses (CRs) are reflexive and targeted motor responses expressed as a result of experience with reward. To evaluate the hypothesis that autoshaping may be a form of impulsive responding, within-subjects correlations between performance on autoshaping and impulsivity tasks were assessed in 15 Long-Evans hooded rats. Autoshaping procedures [insertion of retractable lever conditioned stimulus (CS) followed by the response-independent delivery of food (US)] were followed by testing for impulsive-like responding in a two-choice lever-press operant delay-of-reward procedure (immediate small food reward versus delayed large food reward). Delay-of-reward functions revealed two distinct subject populations. Subjects in the Sensitive group (n=7) were more impulsive-like, increasing immediate reward choices at longer delays for large reward, while those in the Insensitive group (n=8) responded predominantly on only one lever. During the prior autoshaping phase, the Sensitive group had performed more autoshaping CRs, and correlations revealed that impulsive subjects acquired the autoshaping CR in fewer trials. In the Sensitive group, acute injections of ethanol (0, 0.25, 0.50, 1.00, 1.50 g/kg) given immediately before delay-of-reward sessions yielded an inverted U-shaped dose-response curve with increased impulsivity induced by the 0.25, 0.50, and 1.00 g/kg doses of ethanol, while choice strategy of the Insensitive group was not influenced by ethanol dose. Ethanol induced impulsive-like responding only in rats that were flexible in their response strategy (Sensitive group), and this group also performed more autoshaping CRs. Data support the hypothesis that autoshaping and impulsivity are linked.

  13. Delayed manifestation of bilateral scleral thinning after I-BRITE® procedure and review of literature for cosmetic eye-whitening procedures

    Science.gov (United States)

    Moshirfar, Majid; McCaughey, Michael V; Fenzl, Carlton R; Santiago-Caban, Luis; Kramer, Gregory D; Mamalis, Nick

    2015-01-01

    Purpose To report a case of delayed-onset bilateral scleral thinning and calcium deposition following a cosmetic ocular-whitening procedure (I-BRITE®). Methods A 33-year-old male patient with a history of right-sided ptosis repair and left-sided anterior uveitis had previously undergone bilateral I-BRITE treatment for chronic conjunctival hyperemia. Four years after the procedure, the patient was referred to our institution with bilateral scleral thinning and overlying calcific depositions. A literature review was performed through PubMed from 1980 through 2014 using the search terms ‘cosmetic’, ‘ocular’, ‘conjunctivectomy’, ‘regional conjunctivectomy’, ‘I-BRITE’, ‘eye-whitening’, ‘scleritis’, ‘necrotizing scleritis’, ‘anterior uveitis’, ‘mitomycin C’, ‘5-fluorouracil’, and ‘bevacizumab’, along with associated cross-referencing from relevant articles. Results Examination of the patient revealed bilateral necrotizing scleritis within the nasal region of both eyes. Calcified plaques were also present within the areas of scleromalacia, along with epithelial defects demonstrated with fluorescein staining. Although evidence of previous intraocular inflammation was apparent within the left eye, there were no active signs of inflammation evident within either eye on initial presentation. Complication rates reported in the literature include: scleral thinning (1.8%), calcific plaque formation (2.9%), fibrovascular proliferation (13%), diplopia (1.2%), elevation of intraocular pressure (4.2%), and recurrence of conjunctival hyperemia (2.1%). Conclusion Cosmetic ocular whitening procedures have an attendant high complication rate, and have been associated with several adverse postoperative complications, which have in turn generated several reservations regarding the veritable benefit of the procedure. Many postsurgical complications may demonstrate delayed apparition, varying from several months to several years after primary

  14. Delayed manifestation of bilateral scleral thinning after I-BRITE(®) procedure and review of literature for cosmetic eye-whitening procedures.

    Science.gov (United States)

    Moshirfar, Majid; McCaughey, Michael V; Fenzl, Carlton R; Santiago-Caban, Luis; Kramer, Gregory D; Mamalis, Nick

    2015-01-01

    To report a case of delayed-onset bilateral scleral thinning and calcium deposition following a cosmetic ocular-whitening procedure (I-BRITE(®)). A 33-year-old male patient with a history of right-sided ptosis repair and left-sided anterior uveitis had previously undergone bilateral I-BRITE treatment for chronic conjunctival hyperemia. Four years after the procedure, the patient was referred to our institution with bilateral scleral thinning and overlying calcific depositions. A literature review was performed through PubMed from 1980 through 2014 using the search terms 'cosmetic', 'ocular', 'conjunctivectomy', 'regional conjunctivectomy', 'I-BRITE', 'eye-whitening', 'scleritis', 'necrotizing scleritis', 'anterior uveitis', 'mitomycin C', '5-fluorouracil', and 'bevacizumab', along with associated cross-referencing from relevant articles. Examination of the patient revealed bilateral necrotizing scleritis within the nasal region of both eyes. Calcified plaques were also present within the areas of scleromalacia, along with epithelial defects demonstrated with fluorescein staining. Although evidence of previous intraocular inflammation was apparent within the left eye, there were no active signs of inflammation evident within either eye on initial presentation. Complication rates reported in the literature include: scleral thinning (1.8%), calcific plaque formation (2.9%), fibrovascular proliferation (13%), diplopia (1.2%), elevation of intraocular pressure (4.2%), and recurrence of conjunctival hyperemia (2.1%). Cosmetic ocular whitening procedures have an attendant high complication rate, and have been associated with several adverse postoperative complications, which have in turn generated several reservations regarding the veritable benefit of the procedure. Many postsurgical complications may demonstrate delayed apparition, varying from several months to several years after primary surgical intervention as in the case reported here.

  15. Experimental investigation of ultimate loads

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, S M; Larsen, G C; Antoniou, I; Lind, S O; Courtney, M [Risoe National Lab., Wind Energy and Atmospheric Physics, Roskilde (Denmark)

    1999-03-01

    Verification of the structural integrity of a wind turbine involves analysis of fatigue loading as well as ultimate loading. With the trend of persistently growing turbines, the ultimate loading seems to become relatively more important. For wind turbines designed according to the wind conditions prescribed in the IEC-61400 code, the ultimate load is often identified as the leading load parameter. Exemplified by the use of an extensive measurement campaign a procedure for evaluation of the extreme flap-wise bending moments, occurring during normal operating of a wind turbine, is presented. The structural measurements are made on a NEG Micon 650 kW wind turbine erected at a complex high wind site in Oak Creek, California. The turbine is located on the top of a ridge. The prevailing wind direction is perpendicular to the ridge, and the annual mean wind speed is 9.5 m/s. The associated wind field measurement, are taken from two instrumented masts erected less than one rotor diameter in front of the turbine in direction of the prevailing wind direction. Both masts are instrumented at different heights in order to gain insight of the 3D-wind speed structure over the entire rotor plane. Extreme distributions, associated with a recurrence period of 10 minutes, conditioned on the mean wind speed and the turbulence intensity are derived. Combined with the wind climate model proposed in the IEC standard, these distributions are used to predict extreme distributions with recurrence periods equal to one and fifty years, respectively. The synthesis of the conditioned PDF`s and the wind climate model is performed by means of Monte Carlo simulation. (au)

  16. The Ultimate Technology

    DEFF Research Database (Denmark)

    Riis, Søren

    2013-01-01

    One of the most influential philosophers of the 20th century, Martin Heidegger (1889-1976), died prior to the remarkable cloning of the sheep Dolly and before Dr. Venter started his experiments on creating synthetic life, and he never explicitly discussed living technologies. However, by reinterp......One of the most influential philosophers of the 20th century, Martin Heidegger (1889-1976), died prior to the remarkable cloning of the sheep Dolly and before Dr. Venter started his experiments on creating synthetic life, and he never explicitly discussed living technologies. However......, by reinterpreting his notion of "modern technology," this article shows how it is possible to philosophically assess living technologies and to recognize ways in which Heidegger anticipated this phenomenon with his notion of cybernetics. The interpretation elucidates the fundamental process of technology becoming...... living and simultaneously presents living technology as the ultimate technology. The thesis of this article is that living technology is not just one more technology; rather, it is the perfection of technology as understood by Aristotle. Aristotle's thinking is in this way a key example of a profound...

  17. Delayed manifestation of bilateral scleral thinning after I-BRITE® procedure and review of literature for cosmetic eye-whitening procedures

    Directory of Open Access Journals (Sweden)

    Moshirfar M

    2015-03-01

    Full Text Available Majid Moshirfar,1 Michael V McCaughey,2 Carlton R Fenzl,3 Luis Santiago-Caban,4 Gregory D Kramer,3 Nick Mamalis3 1Department of Ophthalmology, Francis I Proctor Foundation, University of California San Francisco, San Francisco, CA, USA; 2University of New Mexico School of Medicine, Albuquerque, NM, USA; 3John A Moran Eye Center, University of Utah, Salt Lake City, UT, USA; 4Department of Ophthalmology, University of Puerto Rico School of Medicine, San Juan, PR, USA Purpose: To report a case of delayed-onset bilateral scleral thinning and calcium deposition following a cosmetic ocular-whitening procedure (I-BRITE®.Methods: A 33-year-old male patient with a history of right-sided ptosis repair and left-sided anterior uveitis had previously undergone bilateral I-BRITE treatment for chronic conjunctival hyperemia. Four years after the procedure, the patient was referred to our institution with bilateral scleral thinning and overlying calcific depositions. A literature review was performed through PubMed from 1980 through 2014 using the search terms ‘cosmetic’, ‘ocular’, ‘conjunctivectomy’, ‘regional conjunctivectomy’, ‘I-BRITE’, ‘eye-whitening’, ‘scleritis’, ‘necrotizing scleritis’, ‘anterior uveitis’, ‘mitomycin C’, ‘5-fluorouracil’, and ‘bevacizumab’, along with associated cross-referencing from relevant articles.Results: Examination of the patient revealed bilateral necrotizing scleritis within the nasal region of both eyes. Calcified plaques were also present within the areas of scleromalacia, along with epithelial defects demonstrated with fluorescein staining. Although evidence of previous intraocular inflammation was apparent within the left eye, there were no active signs of inflammation evident within either eye on initial presentation. Complication rates reported in the literature include: scleral thinning (1.8%, calcific plaque formation (2.9%, fibrovascular proliferation (13%, diplopia (1

  18. A procedure to correct the effects of a relative delay between the quadrature components of radar signals at base band

    Directory of Open Access Journals (Sweden)

    Grydeland

    2005-01-01

    Full Text Available The real and imaginary parts of baseband signals are obtained from a real narrow-band signal by quadrature mixing, i.e. by mixing with cosine and sine signals at the narrow band's selected center frequency. We address the consequences of a delay between the outputs of the quadrature mixer, which arise when digital samples of the quadrature baseband signals are not synchronised, i.e. when the real and imaginary components have been shifted by one or more samples with respect to each other. Through analytical considerations and simulations of such an error on different synthetic signals, we show how this error can be expected to afflict different measurements. In addition, we show the effect of the error on actual incoherent scatter radar data obtained by two different digital receiver systems used in parallel at the EISCAT Svalbard Radar (ESR. The analytical considerations indicate a procedure to correct the error, albeit with some limitations due to a small singular region. We demonstrate the correction procedure on actually afflicted data and compare the results to simultaneously acquired unafflicted data. We also discuss the possible data analysis strategies, including some that avoid dealing directly with the singular region mentioned above.

  19. Incidence and root causes of delays in emergency orthopaedic procedures: a single-centre experience of 36,017 consecutive cases over seven years.

    Science.gov (United States)

    Caesar, Ulla; Karlsson, Jon; Hansson, Elisabeth

    2018-01-01

    Emergency surgery is unplanned by definition and patients are scheduled for surgery with minimal preparation. Some patients who have sustained emergency orthopaedic trauma or other conditions must be operated on immediately or within a few hours, while others can wait until the hospital's resources permit and/or the patients' health status has been optimised as needed. This may affect the prioritisation procedures for both emergency and elective surgery and might result in waiting lists, not only for planned procedures but also for emergencies. The main purpose of this retrospective, observational, single-centre study was to evaluate and describe for the number and reasons of delays, as well as waiting times in emergency orthopaedic surgery using data derived from the hospital's records and registers. All the emergency patients scheduled for emergency surgery whose procedures were rescheduled and delayed between 1 January 2007 and 31 December 2013 were studied. We found that 24% (8474) of the 36,017 patients scheduled for emergency surgeries were delayed and rescheduled at least once, some several times. Eighty per cent of these delays were due to organisational causes. Twenty-one per cent of all the delayed patients had surgery within 24 h, whilst 41% waited for more than 24 h, up to 3 days. A large number of the clinic's emergency orthopaedic procedures were rescheduled and delayed and the majority of the delays were related to organisational reasons. The results can be interpreted in two ways; first, organisational reasons are avoidable and the potential for improvement is great and, secondly and most importantly, the delays might negatively affect patient outcomes.

  20. Reliability Of A Novel Intracardiac Electrogram Method For AV And VV Delay Optimization And Comparability To Echocardiography Procedure For Determining Optimal Conduction Delays In CRT Patients

    Directory of Open Access Journals (Sweden)

    N Reinsch

    2009-03-01

    Full Text Available Background: Echocardiography is widely used to optimize CRT programming. A novel intracardiac electrogram method (IEGM was recently developed as an automated programmer-based method, designed to calculate optimal atrioventricular (AV and interventricular (VV delays and provide optimized delay values as an alternative to standard echocardiographic assessment.Objective: This study was aimed at determining the reliability of this new method. Furthermore the comparability of IEGM to existing echocardiographic parameters for determining optimal conduction delays was verified.Methods: Eleven patients (age 62.9± 8.7; 81% male; 73% ischemic, previously implanted with a cardiac resynchronisation therapy defibrillator (CRT-D underwent both echocardiographic and IEGM-based delay optimization.Results: Applying the IEGM method, concordance of three consecutively performed measurements was found in 3 (27% patients for AV delay and in 5 (45% patients for VV delay. Intra-individual variation between three measurements as assessed by the IEGM technique was up to 20 ms (AV: n=6; VV: n=4. E-wave, diastolic filling time and septal-to-lateral wall motion delay emerged as significantly different between the echo and IEGM optimization techniques (p < 0.05. The final AV delay setting was significantly different between both methods (echo: 126.4 ± 29.4 ms, IEGM: 183.6 ± 16.3 ms; p < 0.001; correlation: R = 0.573, p = 0.066. VV delay showed significant differences for optimized delays (echo: 46.4 ± 23.8 ms, IEGM: 10.9 ± 7.0 ms; p <0.01; correlation: R = -0.278, p = 0.407.Conclusion: The automated programmer-based IEGM-based method provides a simple and safe method to perform CRT optimization. However, the reliability of this method appears to be limited. Thus, it remains difficult for the examiner to determine the optimal hemodynamic settings. Additionally, as there was no correlation between the optimal AV- and VV-delays calculated by the IEGM method and the echo

  1. Prescription Drug Marketing Act of 1987; Prescription Drug Amendments of 1992; policies, requirements, and administrative procedures; delay of effective date. Final rule; delay of effective date.

    Science.gov (United States)

    2004-02-23

    The Food and Drug Administration (FDA) is further delaying, until December 1, 2006, the effective date of certain requirements of a final rule published in the Federal Register of December 3, 1999 (64 FR 67720). In the Federal Register of May 3, 2000 (65 FR 25639), the agency delayed until October 1, 2001, the effective date of certain requirements in the final rule relating to wholesale distribution of prescription drugs by distributors that are not authorized distributors of record, and distribution of blood derivatives by entities that meet the definition of a "health care entity" in the final rule. The agency further delayed the effective date of these requirements in three subsequent Federal Register notices. Most recently, in the Federal Register of January 31, 2003 (68 FR 4912), FDA delayed the effective date until April 1, 2004. This action further delays the effective date of these requirements until December 1, 2006. The final rule implements the Prescription Drug Marketing Act of 1987 (PDMA), as modified by the Prescription Drug Amendments of 1992 (PDA), and the Food and Drug Administration Modernization Act of 1997 (the Modernization Act). The agency is taking this action to address concerns about the requirements in the final rule raised by affected parties. As explained in the SUPPLEMENTARY INFORMATION section, FDA is working with stakeholders through its counterfeit drug initiative to facilitate widespread, voluntary adoption of track and trace technologies that will generate a de facto electronic pedigree, including prior transaction history back to the original manufacturer, as a routine course of business. If this technology is widely adopted, it is expected to help fulfill the pedigree requirements of the PDMA and obviate or resolve many of the concerns that have been raised with respect to the final rule by ensuring that an electronic pedigree travels with a drug product at all times. Therefore, it is necessary to delay the effective date of Sec

  2. Procedural Adaptations for Use of Constant Time Delay to Teach Highly Motivating Words to Beginning Braille Readers

    Science.gov (United States)

    Ivy, Sarah E.; Guerra, Jennifer A.; Hatton, Deborah D.

    2017-01-01

    Introduction: Constant time delay is an evidence-based practice to teach sight word recognition to students with a variety of disabilities. To date, two studies have documented its effectiveness for teaching braille. Methods: Using a multiple-baseline design, we evaluated the effectiveness of constant time delay to teach highly motivating words to…

  3. Ultimate Strength of Ship Hulls under Torsion

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Thayamballi, Anil K.; Pedersen, Preben Terndrup

    2001-01-01

    For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength characte......For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength...... characteristics of ships with large hatch openings. The primary aim of the present study is to investigate the ultimate strength characteristics of ship hulls with large hatch openings under torsion. Axial (warping) as well as shear stresses are normally developed for thin-walled beams with open cross sections...... subjected to torsion. A procedure for calculating these stresses is briefly described. As an illustrative example, the distribution and magnitude of warping and shear stresses for a typical container vessel hull cross section under unit torsion is calculated by the procedure. By theoretical and numerical...

  4. Shear wall ultimate drift limits

    International Nuclear Information System (INIS)

    Duffey, T.A.; Goldman, A.; Farrar, C.R.

    1994-04-01

    Drift limits for reinforced-concrete shear walls are investigated by reviewing the open literature for appropriate experimental data. Drift values at ultimate are determined for walls with aspect ratios ranging up to a maximum of 3.53 and undergoing different types of lateral loading (cyclic static, monotonic static, and dynamic). Based on the geometry of actual nuclear power plant structures exclusive of containments and concerns regarding their response during seismic (i.e.,cyclic) loading, data are obtained from pertinent references for which the wall aspect ratio is less than or equal to approximately 1, and for which testing is cyclic in nature (typically displacement controlled). In particular, lateral deflections at ultimate load, and at points in the softening region beyond ultimate for which the load has dropped to 90, 80, 70, 60, and 50 percent of its ultimate value, are obtained and converted to drift information. The statistical nature of the data is also investigated. These data are shown to be lognormally distributed, and an analysis of variance is performed. The use of statistics to estimate Probability of Failure for a shear wall structure is illustrated

  5. Ultimate disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Roethemeyer, H.

    1991-01-01

    The activities developed by the Federal Institution of Physical Engineering PTB and by the Federal Office for Radiation Protection (BfS) concentrated, among others, on work to implement ultimate storage facilities for radioactive wastes. The book illuminates this development from site designation to the preliminary evaluation of the Gorleben salt dome, to the preparation of planning documents proving that the Konrad ore mine is suitable for a repository. The paper shows the legal provisions involved; research and development tasks; collection of radioactive wastes ready for ultimate disposal; safety analysis in the commissioning and post-operational stages, and product control. The historical development of waste management in the Federal Republic of Germany and international cooperation in this area are outlined. (DG) [de

  6. Ultimate fate of constrained voters

    International Nuclear Information System (INIS)

    Vazquez, F; Redner, S

    2004-01-01

    We examine the ultimate fate of individual opinions in a socially interacting population of leftists, centrists and rightists. In an elemental interaction between agents, a centrist and a leftist can both become centrists or both become leftists with equal rates (and similarly for a centrist and a rightist). However leftists and rightists do not interact. This interaction step between pairs of agents is applied repeatedly until the system can no longer evolve. In the mean-field limit, we determine the exact probability that the system reaches consensus (either leftist, rightist or centrist) or a frozen mixture of leftists and rightists as a function of the initial composition of the population. We also determine the mean time until the final state is reached. Some implications of our results for the ultimate fate in a limit of the Axelrod model are discussed

  7. Ultimate fate of constrained voters

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, F [Department of Physics, Center for BioDynamics, Boston University, Boston, MA 02215 (United States); Redner, S [Department of Physics, Center for Polymer Studies, Boston University, Boston, MA 02215 (United States)

    2004-09-03

    We examine the ultimate fate of individual opinions in a socially interacting population of leftists, centrists and rightists. In an elemental interaction between agents, a centrist and a leftist can both become centrists or both become leftists with equal rates (and similarly for a centrist and a rightist). However leftists and rightists do not interact. This interaction step between pairs of agents is applied repeatedly until the system can no longer evolve. In the mean-field limit, we determine the exact probability that the system reaches consensus (either leftist, rightist or centrist) or a frozen mixture of leftists and rightists as a function of the initial composition of the population. We also determine the mean time until the final state is reached. Some implications of our results for the ultimate fate in a limit of the Axelrod model are discussed.

  8. Transanal Pull-Through Procedure with Delayed versus Immediate Coloanal Anastomosis for Anus-Preserving Curative Resection of Lower Rectal Cancer: A Case-Control Study.

    Science.gov (United States)

    Xiong, Yong; Huang, Ping; Ren, Qing-Gui

    2016-06-01

    This case-control study compared the effectiveness and safety of transanal pull-through procedure (TPP) with delayed or immediate coloanal anastomosis (CAA) for anus-preserving curative resection of lower rectal cancer. Lower rectal cancer patients (n = 128) were hospitalized between January 2003 and December 2013 for elective anus-preserving curative resection through a TPP with delayed (n = 72) or immediate (n = 56) CAA. Main outcome measures including surgical safety, resection radicality, and defecation function were assessed. The two groups were comparable in age, sex, gross pathology, histology, and tumor-node-metastasis staging. Both the delayed and immediate CAA TPPs had similar resection radicality and safety profiles. The immediate CAA was associated with a significantly higher risk of anastomotic leakage and defecation impairment. None of patients in the delayed CAA group experienced anastomotic leakage. In conclusion, TPP with delayed CAA may be superior to immediate CAA in minimizing the risk of anastomotic leakage and relevant surgical morbidities, and does not require a temporary ileostomy and second-look restoration of ostomy.

  9. Hypothetical intertemporal choice and real economic behavior: delay discounting predicts voucher redemptions during contingency-management procedures.

    Science.gov (United States)

    Bickel, Warren K; Jones, Bryan A; Landes, Reid D; Christensen, Darren R; Jackson, Lisa; Mancino, Michael

    2010-12-01

    Delay discounting rates are predictive of drug use status, the likelihood of becoming abstinent, and a variety of health behaviors. Rates of delay discounting may also be related to other relevant behaviors associated with addiction, such as the frequency at which individuals redeem contingency management voucher earnings. This study examined the discounting rates of 152 participants in a buprenorphine treatment program for opioid abuse. Participants received up to 12 weeks of buprenorphine treatment combined with contingency management. Participant's drug use was measured via urine specimens submitted three times a week. Successive negative urine specimens were reinforced with increasing amounts of money. After each negative urine specimen, a participant could either redeem his or her earnings or accumulate it in an account. Analysis of the frequency of redemptions showed that participants with higher rates of delay discounting at study intake redeemed their earnings significantly more often than participants with lower rates of discounting. Age and income also predicted redemption rates. We suggest that delay discounting rates can be used to predict redemption behaviors in a contingency management treatment program and that these findings are consistent with the recent theory of the competing neurobehavioral decision systems. PsycINFO Database Record (c) 2010 APA, all rights reserved.

  10. Delay Discounting Rates Are Temporally Stable in an Equivalent Present Value Procedure Using Theoretical and Area under the Curve Analyses

    Science.gov (United States)

    Harrison, Justin; McKay, Ryan

    2012-01-01

    Temporal discounting rates have become a popular dependent variable in social science research. While choice procedures are commonly employed to measure discounting rates, equivalent present value (EPV) procedures may be more sensitive to experimental manipulation. However, their use has been impeded by the absence of test-retest reliability data.…

  11. Ultimate Explanations of the Universe

    CERN Document Server

    Heller, Michael

    2009-01-01

    We humans are collectively driven by a powerful - yet not fully explained - instinct to understand. We would like to see everything established, proven, laid bare. The more important an issue, the more we desire to see it clarified, stripped of all secrets, all shades of gray. What could be more important than to understand the Universe and ourselves as a part of it? To find a window onto our origin and our destiny? This book examines how far our modern cosmological theories - with their sometimes audacious models, such as inflation, cyclic histories, quantum creation, parallel universes - can take us towards answering these questions. Can such theories lead us to ultimate truths, leaving nothing unexplained? Last, but not least, Heller addresses the thorny problem of why and whether we should expect to find theories with all-encompassing explicative power.

  12. Ultimate loading of wind turbines

    DEFF Research Database (Denmark)

    Larsen, Gunner Chr.; Ronold, K.; Ejsing Jørgensen, Hans

    1999-01-01

    An extreme loading study has been conducted comprising a general wind climate analysis as well as a wind turbine reliability study. In the wind climate analysis, the distribution of the (horizontal) turbulence standard deviation, conditioned on the meanwind speed, has been approximated by fitting......, a design turbulence intensity for off-shore application is proposed which, in the IEC code framework, is applicable for extreme as well as for fatigue loaddetermination. In order to establish a rational method to analyse wind turbine components with respect to failure in ultimate loading, and in addition...... a three parameter Weibull distribution to the measured on-shore and off-shore data for wind speed variations. Specific recommendations on off-shore design turbulence intensities are lacking in the presentIEC-code. Based on the present analysis of the off-shore wind climate on two shallow water sites...

  13. UHS, Ultimate Heat Sink Cooling Pond Analysis

    International Nuclear Information System (INIS)

    Codell, R.; Nuttle, W.K.

    1998-01-01

    1 - Description of program or function: Three programs model performance of an ultimate heat sink cooling pond. National Weather Service data is read and analyzed to predict periods of lowest cooling performance and highest evaporative loss. The data is compared to local site data for significant differences. Then the maximum pond temperature is predicted. Five programs model performance of an ultimate heat sink spray pond. The cooling performance, evaporative water loss, and drift water loss as a function of wind speed are estimated for a spray field. These estimates are used in conjunction with National Weather Service data to predict periods of lowest cooling performance and highest evaporative loss. This data is compared to local site data for significant differences. Then the maximum pond temperature is predicted. 2 - Method of solution: The transfer of heat and water vapor is modeled using an equilibrium temperature procedure for an UHS cooling pond. The UHS spray pond model considers heat, mass, and momentum transfer from a single water drop with the surrounding air, and modification of the surrounding air resulting from the heat, mass, and momentum transfer from many drops in different parts of a spray field. 3 - Restrictions on the complexity of the problem: The program SPRCO uses RANF, a uniform random number generator which is an intrinsic function on the CDC. All programs except COMET use the NAMELIST statement, which is non standard. Otherwise these programs conform to the ANSI Fortran 77 standard. The meteorological data scanning procedure requires tens of years of recorded data to be effective. The models and methods, provided as useful tool for UHS analyses of cooling ponds and spray ponds, are intended as guidelines only. Use of these methods does not automatically assure NRC approval, nor are they required procedures for nuclear-power-plant licensing

  14. Development and validation of a screening procedure to identify speech-language delay in toddlers with cleft palate

    DEFF Research Database (Denmark)

    Jørgensen, Line Dahl; Willadsen, Elisabeth

    2017-01-01

    condition based on assessment of consonant inventory using a real-time listening procedure in combination with parent-reported expressive vocabulary. These measures allowed evaluation of early speech-language skills found to correlate significantly with later speech-language difficulties in longitudinal......The purpose of this study was to develop and validate a clinically useful speech-language screening procedure for young children with cleft palate +/- cleft lip (CP) to identify those in need of speech-language intervention. Twenty-two children with CP were assigned to a +/- need for intervention...... studies of children with CP. The external validity of this screening procedure was evaluated by comparing the +/- need for intervention assignment determined by the screening procedure to experienced speech-language pathologists’ (SLPs’) clinical judgment of whether or not a child needed early...

  15. Ultimate explanations and suboptimal choice.

    Science.gov (United States)

    Vasconcelos, Marco; Machado, Armando; Pandeirada, Josefa N S

    2018-07-01

    Researchers have unraveled multiple cases in which behavior deviates from rationality principles. We propose that such deviations are valuable tools to understand the adaptive significance of the underpinning mechanisms. To illustrate, we discuss in detail an experimental protocol in which animals systematically incur substantial foraging losses by preferring a lean but informative option over a rich but non-informative one. To understand how adaptive mechanisms may fail to maximize food intake, we review a model inspired by optimal foraging principles that reconciles sub-optimal choice with the view that current behavioral mechanisms were pruned by the optimizing action of natural selection. To move beyond retrospective speculation, we then review critical tests of the model, regarding both its assumptions and its (sometimes counterintuitive) predictions, all of which have been upheld. The overall contention is that (a) known mechanisms can be used to develop better ultimate accounts and that (b) to understand why mechanisms that generate suboptimal behavior evolved, we need to consider their adaptive value in the animal's characteristic ecology. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. Influence of initial imperfections on ultimate strength of spherical shells

    Directory of Open Access Journals (Sweden)

    Chang-Li Yu

    2017-09-01

    Full Text Available Comprehensive consideration regarding influence mechanisms of initial imperfections on ultimate strength of spherical shells is taken to satisfy requirement of deep-sea structural design. The feasibility of innovative numerical procedure that combines welding simulation and non-linear buckling analysis is verified by a good agreement to experimental and theoretical results. Spherical shells with a series of wall thicknesses to radius ratios are studied. Residual stress and deformations from welding process are investigated separately. Variant influence mechanisms are discovered. Residual stress is demonstrated to be influential to stress field and buckling behavior but not to the ultimate strength. Deformations are proved to have a significant impact on ultimate strength. When central angles are less than critical value, concave magnitudes reduce ultimate strengths linearly. However, deformations with central angles above critical value are of much greater harm. Less imperfection susceptibility is found in spherical shells with larger wall thicknesses to radius ratios.

  17. THE ULTIMATE STATE CONCEPT APPLIED TO TUNNEL SUPPORT

    Directory of Open Access Journals (Sweden)

    Mladen Hudec

    2000-12-01

    Full Text Available The most questionable are the values of pressures between rock and support resulting from common deformations on the contact area between rock and support. Therefore the modelling and design of the tunnel support is not reliable, if it is based on active rock pressure resulting from this common deformations. The inversion of the design procedure is proposed. Instead of the active extreme pressure of the rock on support, the influence of ultimate reaction of the support on the rock has to be analysed. This procedure can be performed using the ultimate load principle, as proposed by Eurocodc 7 (Geotechnies. Normally, the rock has the tendency to increase the common conver¬gence until the support reaches its ultimate state. So, loading of profile boundary with the ultimate possible reaction of the support is very plausible. The reactive support pressures have to be probable and itself in equilibrium. The ultimate reactive load has to be reduced by Euro-code safety factor for structural elements and applied on the rock with given properties, or alternatively (as proposed by Eurocode 7 the soil or rock properties have to be diminished and calculated with full ultimate support pressures. If the rock with given (or proposed pro¬perties and loaded with ultimate reactive pressures resulting from supposed support, satisfy its failure criterion, then is the compound system support-rock verificatcd. By this procedure, the number of relevant material properties is reduce to the primary stress ratio and the constants defining the failure criterion. The verification can be performed by any of numerical methods, but we prefer here used boundary elements method (the paper is published in Croatian.

  18. No More Waits and Delays: Streamlining Workflow to Decrease Patient Time of Stay for Image-guided Musculoskeletal Procedures.

    Science.gov (United States)

    Cheung, Yvonne Y; Goodman, Eric M; Osunkoya, Tomiwa O

    2016-01-01

    Long wait times limit our ability to provide the right care at the right time and are commonly products of inefficient workflow. In 2013, the demand for musculoskeletal (MSK) procedures increased beyond our department's ability to provide efficient and timely service. We initiated a quality improvement (QI) project to increase efficiency and decrease patient time of stay. Our project team included three MSK radiologists, one senior resident, one technologist, one administrative assistant/scheduler, and the lead technologist. We adopted and followed the Lean Six Sigma DMAIC (define, measure, analyze, improve, and control) approach. The team used tools such as voice of the customer (VOC), along with affinity and SIPOC (supplier, input, process, output, customer) diagrams, to understand the current process, identify our customers, and develop a project charter in the define stage. During the measure stage, the team collected data, created a detailed process map, and identified wastes with the value stream mapping technique. Within the analyze phase, a fishbone diagram helped the team to identify critical root causes for long wait times. Scatter plots revealed relationships among time variables. Team brainstorming sessions generated improvement ideas, and selected ideas were piloted via plan, do, study, act (PDSA) cycles. The control phase continued to enable the team to monitor progress using box plots and scheduled reviews. Our project successfully decreased patient time of stay. The highly structured and logical Lean Six Sigma approach was easy to follow and provided a clear course of action with positive results. (©)RSNA, 2016.

  19. The dream of an ultimate theory

    International Nuclear Information System (INIS)

    Weinberg, S.

    1997-10-01

    Steven Weinberg describes how the dream of an ultimate theory began when one tried to unify the fundamental laws governing the stars constellations as elementary particles: electromagnetism, weak-electro theory then standard model which gives only one quantity out of its fields, the gravitation. He tries to explain to what an ultimate theory could look like. but the dream of an ultimate theory is not yet realized, there are some elementary particles to find before and then to build superconducting super colliders. The europe made it. the dream of an ultimate theory became an european dream. (N.C.)

  20. Concussion Prevalence in Competitive Ultimate Frisbee Players

    Science.gov (United States)

    Lazar, Damien J.; Lichtenstein, Jonathan D.; Tybor, David J.

    2018-01-01

    Background: Ultimate Frisbee (ultimate) is a fast-growing, popular sport played nationally by over 4 million athletes. While several studies have examined injury rates in ultimate, no work has investigated the prevalence of concussions specifically or players’ knowledge and management of those injuries. Purpose: To estimate the lifetime prevalence of concussions in ultimate and to assess players’ knowledge of concussions as well as their concussion management behaviors. Study Design: Descriptive epidemiology study. Methods: From June to November 2015, we collected ultimate-related concussion data via an anonymous web-based survey, the Concussion in Ultimate Frisbee Survey, from a convenience sample of 787 male and female ultimate players across the United States. Results: There were 553 male and 234 female respondents included in the analysis; 26.58% of men and 24.79% of women reported that they had sustained at least 1 concussion while playing ultimate, with 45.58% and 43.10% of those men and women, respectively, reporting multiple concussions. A total of 67.81% of men and 78.21% of women stated that they would remove themselves from play after sustaining a given concussion, although 45.99% of men and 37.62% of women indicated that they had returned to play in the same game or practice. Conclusion: Our preliminary data suggest that concussions do commonly occur in competitive ultimate and that better education and management of concussions in ultimate athletes are needed. This study is an important first step in deepening our understanding of these issues. PMID:29552572

  1. Physical demands in competitive ultimate frisbee

    DEFF Research Database (Denmark)

    Krustrup, Peter; Mohr, Magni

    2015-01-01

    The objective was to study game demands in competitive ultimate Frisbee by performing match analysis during a game. Thirteen moderately trained (Yo-Yo intermittent recovery test levels 1 and 2 [Yo-Yo IR1 and IR2] performance: 1790 ± 382 m and 657 ± 225 m, respectively) competitive male ultimate...... = 0.74, p ≤ 0.05). Ultimate Frisbee is an intense intermittent team sport with high cardiovascular loading and clear indications of fatigue toward the end of each half. Yo-Yo IR test performances correlate with physical match performance....

  2. Ultimate Electrical Means for Severe Accident and Multi Unit Event Management

    International Nuclear Information System (INIS)

    Guisez, Xavier

    2015-01-01

    Following the Multi Unit Severe Accident that occurred at Fukushima as a result of the tsunami on 11 March 2011, the European Council decided to submit its Nuclear Power Plants to a Stress Test. In Belgium, this Stress Test, named BEST (Belgian Stress Test), was successfully concluded at the end of 2011. Nevertheless, Electrabel decided, in agreement with the Authorities, to start a beyond design basis action plan, with the goal to mitigate the consequences of a Beyond Design Basis Accident and a Multi Unit Event. Consequently, this has led to an improvement of the robustness of its Nuclear Power Plants. Considering the importance of electrical power supply to a nuclear power plant, a significant part of this action plan consisted of setting up a mobile, 'plug and play' method for the electrical power supply to some major safety systems. In order to install this ultimate power supply, three factors were retained as essential. First, important reactor monitoring instrumentation is preserved. Second, core cooling is provided at all times. Finally, systems are easily made operational within a very short delay of time. During normal operation and Design Basis Events, core cooling is provided by High Voltage equipment. However, during high stress circumstances, it is too complex to realize connections on this equipment. Therefore, analysis was performed to realize core cooling with, easier to handle, Low Voltage equipment. These systems are powered by several GenSets, especially designed and manufactured for this application. The outcome of this project are easy to use, ultimate means, that supply electric power to important safety systems in order to drastically reduce the risk of core damage, during a beyond design basis event. Additionally, for all ultimate means, procedures and training modules were developed for the operators. (authors)

  3. Ultimate and proximate explanations of strong reciprocity.

    Science.gov (United States)

    Vromen, Jack

    2017-08-23

    Strong reciprocity (SR) has recently been subject to heated debate. In this debate, the "West camp" (West et al. in Evol Hum Behav 32(4):231-262, 2011), which is critical of the case for SR, and the "Laland camp" (Laland et al. in Science, 334(6062):1512-1516, 2011, Biol Philos 28(5):719-745, 2013), which is sympathetic to the case of SR, seem to take diametrically opposed positions. The West camp criticizes advocates of SR for conflating proximate and ultimate causation. SR is said to be a proximate mechanism that is put forward by its advocates as an ultimate explanation of human cooperation. The West camp thus accuses advocates of SR for not heeding Mayr's original distinction between ultimate and proximate causation. The Laland camp praises advocates of SR for revising Mayr's distinction. Advocates of SR are said to replace Mayr's uni-directional view on the relation between ultimate and proximate causes by the bi-directional one of reciprocal causation. The paper argues that both the West camp and the Laland camp misrepresent what advocates of SR are up to. The West camp is right that SR is a proximate cause of human cooperation. But rather than putting forward SR as an ultimate explanation, as the West camp argues, advocates of SR believe that SR itself is in need of ultimate explanation. Advocates of SR tend to take gene-culture co-evolutionary theory as the correct meta-theoretical framework for advancing ultimate explanations of SR. Appearances notwithstanding, gene-culture coevolutionary theory does not imply Laland et al.'s notion of reciprocal causation. "Reciprocal causation" suggests that proximate and ultimate causes interact simultaneously, while advocates of SR assume that they interact sequentially. I end by arguing that the best way to understand the debate is by disambiguating Mayr's ultimate-proximate distinction. I propose to reserve "ultimate" and "proximate" for different sorts of explanations, and to use other terms for distinguishing

  4. Ultimate justification: Wittgenstein and medical ethics.

    Science.gov (United States)

    Hughes, J

    1995-02-01

    Decisions must be justified. In medical ethics various grounds are given to justify decisions, but ultimate justification seems illusory and little considered. The philosopher Wittgenstein discusses the problem of ultimate justification in the context of general philosophy. His comments, nevertheless, are pertinent to ethics. From a discussion of Wittgensteinian notions, such as 'bedrock', the idea that 'ultimate' justification is grounded in human nature as such is derived. This discussion is relevant to medical ethics in at least five ways: it shows generally what type of certainty there is in practical ethics; it seems to imply some objective foundation to our ethical judgements; it squares with our experience of making ethical decisions; it shows something of the nature of moral arguments; and, finally, it has implications for teaching medicine and ethics.

  5. Prescription Drug Marketing Act of 1987; Prescription Drug Amendments of 1992; policies, requirements, and administrative procedures; delay of effective date; reopening of administrative record. Food and Drug Administration, HHS. Final rule; delay of effective date; reopening of administrative record.

    Science.gov (United States)

    2000-05-03

    The Food and Drug Administration (FDA) is delaying until October 1, 2001, the effective date and reopening the administrative record to receive additional comments regarding certain requirements of a final rule published in the Federal Register of December 3, 1999 (64 FR 67720). The other provisions of the final rule become effective on December 4, 2000. The final rule implements the Prescription Drug Marketing Act of 1987 (PDMA), as modified by the Prescription Drug Amendments of 1992 (PDA) and the FDA Modernization Act of 1997 (the Modernization Act). FDA is delaying the effective date for certain requirements relating to wholesale distribution of prescription drugs by distributors that are not authorized distributors of record. FDA is also delaying the effective date of another requirement that would prohibit blood centers functioning as "health care entities" to act as wholesale distributors of blood derivatives. The agency is taking this action to address numerous concerns about the provisions raised by affected parties.

  6. 78 FR 55117 - Ultimate Heat Sink for Nuclear Power Plants; Draft Regulatory Guide

    Science.gov (United States)

    2013-09-09

    ... NUCLEAR REGULATORY COMMISSION [NRC-2013-0203] Ultimate Heat Sink for Nuclear Power Plants; Draft... (DG), DG-1275, ``Ultimate Heat Sink for Nuclear Power Plants.'' This regulatory guide (RG) describes methods and procedures acceptable to the NRC staff that nuclear power plant facility licensees and...

  7. Librarians Are the Ultimate Knowledge Managers?

    Science.gov (United States)

    Koina, Cathie

    2003-01-01

    Librarians are the ultimate knowledge managers. Everyone knows that. After all, haven't they been the custodians of documented knowledge for centuries? Who could possibly do it better than them? Well, then why aren't people knocking down their doors, begging them to be the knowledge managers of the organisation? Are they just ignorant of how…

  8. Ultimate gradient in solid-state accelerators

    International Nuclear Information System (INIS)

    Whittum, D.H.

    1998-08-01

    The authors recall the motivation for research in high-gradient acceleration and the problems posed by a compact collider. They summarize the phenomena known to appear in operation of a solid-state structure with large fields, and research relevant to the question of the ultimate gradient. They take note of new concepts, and examine one in detail, a miniature particle accelerator based on an active millimeter-wave circuit and parallel particle beams

  9. The ultimate disposition of depleted uranium

    Energy Technology Data Exchange (ETDEWEB)

    Lemons, T.R. [Uranium Enrichment Organization, Oak Ridge, TN (United States)

    1991-12-31

    Depleted uranium (DU) is produced as a by-product of the uranium enrichment process. Over 340,000 MTU of DU in the form of UF{sub 6} have been accumulated at the US government gaseous diffusion plants and the stockpile continues to grow. An overview of issues and objectives associated with the inventory management and the ultimate disposition of this material is presented.

  10. Hydrogeological problems in the ultimate storage of radioactive wastes

    International Nuclear Information System (INIS)

    Uerpmann, E.P.

    1980-01-01

    The following work shows how one can achieve the safe closure of ultimate-stored radioactive wastes by connecting a series of various barriers to the biosphere. The propagation of radionuclides by ground water is considered to be the most important long-term transport mechanism. Salt occurences in the Federal Republic of Germany are considered to be the best form suitable for end storage formations for known reasons. When not observing mining and hydrogeological knowledge, the danger of uncontrollable water flow in the end storage can arise from the water solubility of the salt rocks. Therefore the filling of salt mines and the subsequent procedures are dealt with in detail. The leading of radioactive nuclides is influenced by the properties of the ultimately stored wastes and by the quality of the remaining filling of the caves. These problems are dealt with in detail. A series of barriers to the closure of the underground caves are suggested and discussed. The most important barriers consist of the stability of the corresponding selected end storage structure. Possible arrangements of the storage cave are given which even after storage must maintain a high stability. Proposals are made on how the ultimately stored wastes can protect themselves against contact with free water or salt solutions. (orig.) [de

  11. The ultimate disposition of depleted uranium

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-01

    Significant amounts of the depleted uranium (DU) created by past uranium enrichment activities have been sold, disposed of commercially, or utilized by defense programs. In recent years, however, the demand for DU has become quite small compared to quantities available, and within the US Department of Energy (DOE) there is concern for any risks and/or cost liabilities that might be associated with the ever-growing inventory of this material. As a result, Martin Marietta Energy Systems, Inc. (Energy Systems), was asked to review options and to develop a comprehensive plan for inventory management and the ultimate disposition of DU accumulated at the gaseous diffusion plants (GDPs). An Energy Systems task team, under the chairmanship of T. R. Lemons, was formed in late 1989 to provide advice and guidance for this task. This report reviews options and recommends actions and objectives in the management of working inventories of partially depleted feed (PDF) materials and for the ultimate disposition of fully depleted uranium (FDU). Actions that should be considered are as follows. (1) Inspect UF{sub 6} cylinders on a semiannual basis. (2) Upgrade cylinder maintenance and storage yards. (3) Convert FDU to U{sub 3}O{sub 8} for long-term storage or disposal. This will include provisions for partial recovery of costs to offset those associated with DU inventory management and the ultimate disposal of FDU. Another recommendation is to drop the term tails'' in favor of depleted uranium'' or DU'' because the tails'' label implies that it is waste.'' 13 refs.

  12. Manipulation of Motivating Operations and Use of a Script-Fading Procedure to Teach Mands for Location to Children with Language Delays

    Science.gov (United States)

    Howlett, Melissa A.; Sidener, Tina M.; Progar, Patrick R.; Sidener, David W.

    2011-01-01

    The effects of contriving motivating operations (MOs) and script fading on the acquisition of the mand "Where's [object]?" were evaluated in 2 boys with language delays. During each session, trials were alternated in which high-preference items were present (abolishing operation [AO] trials) or missing (establishing operation [EO] trials) from…

  13. MANIPULATION OF MOTIVATING OPERATIONS AND USE OF A SCRIPT-FADING PROCEDURE TO TEACH MANDS FOR LOCATION TO CHILDREN WITH LANGUAGE DELAYS

    OpenAIRE

    Howlett, Melissa A; Sidener, Tina M; Progar, Patrick R; Sidener, David W

    2011-01-01

    The effects of contriving motivating operations (MOs) and script fading on the acquisition of the mand “Where's [object]?” were evaluated in 2 boys with language delays. During each session, trials were alternated in which high-preference items were present (abolishing operation [AO] trials) or missing (establishing operation [EO] trials) from their typical locations. Both participants learned to mand during EO trials and not to mand during AO trials during training. Generalization of manding...

  14. Ultimately short ballistic vertical graphene Josephson junctions

    Science.gov (United States)

    Lee, Gil-Ho; Kim, Sol; Jhi, Seung-Hoon; Lee, Hu-Jong

    2015-01-01

    Much efforts have been made for the realization of hybrid Josephson junctions incorporating various materials for the fundamental studies of exotic physical phenomena as well as the applications to superconducting quantum devices. Nonetheless, the efforts have been hindered by the diffusive nature of the conducting channels and interfaces. To overcome the obstacles, we vertically sandwiched a cleaved graphene monoatomic layer as the normal-conducting spacer between superconducting electrodes. The atomically thin single-crystalline graphene layer serves as an ultimately short conducting channel, with highly transparent interfaces with superconductors. In particular, we show the strong Josephson coupling reaching the theoretical limit, the convex-shaped temperature dependence of the Josephson critical current and the exceptionally skewed phase dependence of the Josephson current; all demonstrate the bona fide short and ballistic Josephson nature. This vertical stacking scheme for extremely thin transparent spacers would open a new pathway for exploring the exotic coherence phenomena occurring on an atomic scale. PMID:25635386

  15. Ultimate-gradient accelerators physics and prospects

    CERN Document Server

    Skrinsky, Aleksander Nikolayevich

    1995-01-01

    As introduction, the needs and ways for ultimate acceleration gradients are discussed briefly. The Plasma Wake Field Acceleration is analized in the most important details. The structure of specific plasma oscillations and "high energy driver beam SP-plasma" interaction is presented, including computer simulation of the process. Some pratical ways to introduce the necessary mm-scale bunching in driver beam and to arrange sequential energy multiplication are dicussed. The influence of accelerating beam particle - plasma binary collisions is considered, also. As applications of PWFA, the use of proton super-colliders beams (LHC and Future SC) to drive the "multi particle types" accelerator, and the arrangements for the electron-positron TeV range collider are discussed.

  16. Ultimate load capacities of expansion anchor bolts

    International Nuclear Information System (INIS)

    Czarnecki, R.M.; Manrique, M.A.; Samaddar, S.K.

    1993-01-01

    A summary of available experimental expansion anchor bolt test data is presented. These data were collected as part of programs by the nuclear industry to address generic issues related to verification of seismic adequacy of equipment in nuclear power plants. Some of the data presented are suitable for use in seismic probabilistic risk assessments. For example, mean values of ultimate strength, along with their standard deviation and coefficients of variation, for a range of most typical expansion anchor bolt sizes are presented. Effects of interaction between shear and tension, edge distance, spacing, and cracking of the concrete are presented in a manner that is more suitable for use in deterministic evaluations. Related industry programs to derive anchor bolt capacities are briefly discussed. Recommendations for areas of further investigation are also presented

  17. Focused ion beam technology and ultimate applications

    International Nuclear Information System (INIS)

    Gierak, Jacques

    2009-01-01

    In this topical review, the potential of the focused ion beam (FIB) technology and ultimate applications are reviewed. After an introduction to the technology and to the operating principles of liquid metal ion sources (LMIS), of ion optics and instrument architectures, several applications are described and discussed. First, the application of FIB for microcircuit inspection, metrology and failure analysis is presented. Then, we introduce and illustrate some advanced patterning schemes we propose as next generation FIB processing examples. These patterning schemes are (i) local defect injection or smoothing in magnetic thin film direct patterning, (ii) functionalization of graphite substrates to guide organization of clusters, (iii) local and selective epitaxy of III–V semiconductor quantum dots and (iv) FIB patterned solid-state nanopores for biological molecules manipulation and analysis. We conclude this work by giving our vision of the future developments for FIB technology. (topical review)

  18. Transcending matter: physics and ultimate meaning.

    Science.gov (United States)

    Paulson, Steve; Frank, Adam; Kaiser, David; Maudlin, Tim; Natarajan, Priyamvada

    2015-12-01

    From the discovery of new galaxies and nearly undetectable dark energy to the quantum entanglement of particles across the universe, new findings in physics naturally elicit a sense of awe and wonder. For the founders of modern physics-from Einstein and Bohr to Heisenberg, Pauli, and Bohm-a fascination with deeper questions of meaning and ultimate reality led some of them to explore esoteric traditions and metaphysics. More recently, however, physicists have largely shunned such philosophical and spiritual associations. What can contemporary physics offer us in the quest to understand our place in the universe? Has physics in some ways become a religion unto itself that rejects the search for existential meaning? Discussion of these and related questions is presented in this paper. © 2015 New York Academy of Sciences.

  19. Delayed fission

    Energy Technology Data Exchange (ETDEWEB)

    Hatsukawa, Yuichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-07-01

    Delayed fission is a nuclear decay process that couples {beta} decay and fission. In the delayed fission process, a parent nucleus undergoes {beta} decay and thereby populates excited states in the daughter. If these states are of energies comparable to or greater than the fission barrier of the daughter, then fission may compete with other decay modes of the excited states in the daughter. In this paper, mechanism and some experiments of the delayed fission will be discussed. (author)

  20. Healthy aging: The ultimate preventative medicine.

    Science.gov (United States)

    Kaeberlein, Matt; Rabinovitch, Peter S; Martin, George M

    2015-12-04

    Age is the greatest risk factor for nearly every major cause of mortality in developed nations. Despite this, most biomedical research focuses on individual disease processes without much consideration for the relationships between aging and disease. Recent discoveries in the field of geroscience, which aims to explain biological mechanisms of aging, have provided insights into molecular processes that underlie biological aging and, perhaps more importantly, potential interventions to delay aging and promote healthy longevity. Here we describe some of these advances, along with efforts to move geroscience from the bench to the clinic. We also propose that greater emphasis should be placed on research into basic aging processes, because interventions that slow aging will have a greater effect on quality of life compared with disease-specific approaches. Copyright © 2015, American Association for the Advancement of Science.

  1. Wall roughness induces asymptotic ultimate turbulence

    Science.gov (United States)

    Zhu, Xiaojue; Verschoof, Ruben A.; Bakhuis, Dennis; Huisman, Sander G.; Verzicco, Roberto; Sun, Chao; Lohse, Detlef

    2018-04-01

    Turbulence governs the transport of heat, mass and momentum on multiple scales. In real-world applications, wall-bounded turbulence typically involves surfaces that are rough; however, characterizing and understanding the effects of wall roughness on turbulence remains a challenge. Here, by combining extensive experiments and numerical simulations, we examine the paradigmatic Taylor-Couette system, which describes the closed flow between two independently rotating coaxial cylinders. We show how wall roughness greatly enhances the overall transport properties and the corresponding scaling exponents associated with wall-bounded turbulence. We reveal that if only one of the walls is rough, the bulk velocity is slaved to the rough side, due to the much stronger coupling to that wall by the detaching flow structures. If both walls are rough, the viscosity dependence is eliminated, giving rise to asymptotic ultimate turbulence—the upper limit of transport—the existence of which was predicted more than 50 years ago. In this limit, the scaling laws can be extrapolated to arbitrarily large Reynolds numbers.

  2. On the ultimate uncertainty of the top quark pole mass

    Energy Technology Data Exchange (ETDEWEB)

    Beneke, M. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Marquard, P. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Nason, P. [INFN, Sezione di Milano Bicocca (Italy); Steinhauser, M. [Karlsruher Institut fuer Technologie (Germany). Inst. fuer Theoretische Teilchenphysik

    2016-05-15

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS mass, and conclude that this uncertainty is around 70 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be 250 MeV.

  3. On the ultimate uncertainty of the top quark pole mass

    International Nuclear Information System (INIS)

    Beneke, M.; Nason, P.; Steinhauser, M.

    2016-05-01

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS mass, and conclude that this uncertainty is around 70 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be 250 MeV.

  4. On the ultimate uncertainty of the top quark pole mass

    Science.gov (United States)

    Beneke, M.; Marquard, P.; Nason, P.; Steinhauser, M.

    2017-12-01

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS ‾ mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS ‾ mass. Including an estimate of the internal bottom and charm quark mass effect, we conclude that this uncertainty is around 110 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be around 300 MeV.

  5. Ultimate disposal: a plan for achievement

    International Nuclear Information System (INIS)

    Bartlett, J.W.

    1975-01-01

    Four major topics relevant to R and D plans for disposal were: functions of planning, plans development procedures, R and D program procedures, and R and D plans content. Comments on these topics emphasize four major points: plans and their results support decisions on disposal methods; decisions will winnow options on the basis of comprehensive assessments; the R and D plan for disposal will be comprehensive and maintain options; time frame for the R and D program may be about 20 years. Prior and on-going work has provided a good foundation for this planning effort and the content of the plans. The R and D plans are expected to be developed this year and updated periodically

  6. The ultimate challenge of cloacal exstrophy.

    Science.gov (United States)

    Schober, Justine M; Carmichael, Polly A; Hines, Melissa; Ransley, Philip G

    2002-01-01

    Our review addresses the various system abnormalities associated with cloacal exstrophy and revisits the question of gender assignment. Gender assignment decisions and psychological aspects of gender issues have become the "ultimate challenge." Exploration of gender identity, gender role behavior and sexual orientation has just begun. A comprehensive literature review was performed with all world literature regarding the current management of cloacal exstrophy. Research focused on management principles, outcomes and documentation of concurrent anomalies. We also describe original research evaluating gender identity in our own series of patients raised as girls to illustrate the challenge of treatment and augment the available literature, which is scant. Abnormalities of the vertebral column ranged from hemivertebra to myelomeningocele. With magnetic resonance imaging, the incidence of spinal dysraphism approached 100% and cord tethering was also more frequently recognized. For children with the short bowel syndrome, advances in antibiotic usage, and parenteral and enteral nutrition have increased the survival rate and reduced morbidity. A neurological component has been recognized for bladder function, bladder neck continence, lower extremity function and erectile capacity. Mitrofanoff-type reconstruction with bladder neck closure and continent catheterizable stoma dramatically increased continence. Diminutive or absent penis has been documented in 30% of males, and no documentation of paternity exists. The majority of females have bicornuate uterus. However, ovaries and tubes were generally normal. No reports of proven fertility exist. The strategy and timing of surgery relating to gender assignment remain controversial. A desperate need exists for research focusing on gender development and quality of life. Until that time, a cautious watchful approach may be most appropriate as our patients with cloacal exstrophy mature into adulthood.

  7. Maintained ship hull girder ultimate strength reliability considering corrosion and fatigue

    DEFF Research Database (Denmark)

    Hu, Yong; Cui, W.; Pedersen, Preben Terndrup

    2004-01-01

    The prupose of this paper is to propose a methodology to assess the time-variant ultimate strength of ship hull girder under the degradations of corrosion and fatigue. The effects of fatigue cracks on the tensile and compressive residual ultimate strength of stiffened panels and unstiffened plates......, webs and flanges, respectively. The effects of inspections and repair are taken into account. A minimum net thickness rule is used to determine repair policies. A procedure is proposed to determine the maximum allowable corrosion thickness of different parts of the hull cross section. The procedure...

  8. Delayed Ejaculation

    Science.gov (United States)

    ... cases, it is due to a combination of physical and psychological concerns. Psychological causes of delayed ejaculation include: Depression, anxiety or other mental health conditions Relationship problems due to stress, poor communication ...

  9. Delayed growth

    Science.gov (United States)

    ... Slow rate of growth; Retarded growth and development; Growth delay Images Toddler development References Cooke DW, Divall SA, Radovick S. Normal and aberrant growth in children. In: Melmed S, Polonsky KS, Larsen PR, ...

  10. A study on nonlinear behavior of reactor containment structures during ultimate accident condition(I)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Hoon; Kim, Young Jin; Park, Joo Yeon [Youngdong Univ., Yeongdong (Korea, Republic of)] (and others)

    2003-03-15

    In this study, the following scope and contents are established for first year's study of determining ultimate pressure capacity of CANDU-type reactor containment. State-of-arts on the prediction of the ultimate pressure capacity of prestressed concrete reactor containment. Comparative study on structural characteristics and analysis model of CANDU-type reactor containment. State-of-arts on evaluation method of the ultimate pressure capacity of prestressed concrete reactor containment. Enhancement of evaluation method of the ultimate pressure capacity for PWR containment structure. In order to determine a realistic lower bound of a typical reactor containment structural capacity for internal pressure, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate capacity are required. Especially, the in-depth evaluation of modeling technique and analysis procedure for determining ultimate pressure capacity of CANDU-type reactor containment is required. Therefore, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate pressure capacity of CANDU-type reactor containment for internal pressure will be suggested in this study.

  11. A study on nonlinear behavior of reactor containment structures during ultimate accident condition(I)

    International Nuclear Information System (INIS)

    Kim, Sun Hoon; Kim, Young Jin; Park, Joo Yeon

    2003-03-01

    In this study, the following scope and contents are established for first year's study of determining ultimate pressure capacity of CANDU-type reactor containment. State-of-arts on the prediction of the ultimate pressure capacity of prestressed concrete reactor containment. Comparative study on structural characteristics and analysis model of CANDU-type reactor containment. State-of-arts on evaluation method of the ultimate pressure capacity of prestressed concrete reactor containment. Enhancement of evaluation method of the ultimate pressure capacity for PWR containment structure. In order to determine a realistic lower bound of a typical reactor containment structural capacity for internal pressure, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate capacity are required. Especially, the in-depth evaluation of modeling technique and analysis procedure for determining ultimate pressure capacity of CANDU-type reactor containment is required. Therefore, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate pressure capacity of CANDU-type reactor containment for internal pressure will be suggested in this study

  12. Progressive loss of pancreatic function in chronic pancreatitis is delayed by main pancreatic duct decompression. A longitudinal prospective analysis of the modified puestow procedure.

    Science.gov (United States)

    Nealon, W H; Thompson, J C

    1993-05-01

    This study evaluated the effect of operative drainage of the main pancreatic duct (MPD) on functional derangements associated with chronic pancreatitis (CP). The author previously reported delayed functional impairment in an evaluation of the impact of operative drainage in patients with CP. The author now reports on a prospective study of 143 patients with this diagnosis. Each patient underwent 1) ERCP, 2) the Bentiromide PABA, 3) 72-hour fecal fat test, 4) oral glucose tolerance test (OGTT) and 5) fat meal (LIPOMUL)--stimulated pancreatic polypeptide release (PP). All patients were stratified as mild/moderate (M/M) or severe CP on the basis of a 5-point system that was developed by the author. Patients were studied at 16-month intervals. All 143 patients underwent initial and follow-up evaluations in a mean follow-up of 47.3 months; 83 of 143 patients had M/M grade at initial evaluation. Eighty-seven patients underwent (MPD) decompression to relieve abdominal pain. In a separate prospective 17 patients with a diagnosis of CP, a grade of M/M and non-disabling abdominal pain were randomized to operative or non-operative treatment; 9 of these randomized patients were operated upon and 8 were not. No patient improved their grade during follow-up; 47 of 83 M/M patients had operative drainage and 36 did not. This grade was preserved in 41 of 47 (87%) operated patients but in only 8 of the 36 non-operated patients (22%). In the randomized trial, seven of nine operated patients retained their functional status in follow-up, whereas only two of eight patients (25%) randomized to non-operation preserved their functional grade. These data in this large study as well as among a previous randomized sample, support a policy of early operative drainage before the development of irreversible functional impairment in patients with chronic pancreatitis and associated dilation of the main pancreatic duct.

  13. Developmental delay

    Science.gov (United States)

    Nutrition support is essential for the care of the child with developmental delay. After a thorough evaluation, an individualized intervention plan that accounts for the child’s nutrition status, feeding ability, and medical condition may be determined. Nutrition assessments may be performed at leas...

  14. Direct ultimate disposal of spent fuel DEAB. Systems analysis. Ultimate disposal concepts. Final report. Main volume

    International Nuclear Information System (INIS)

    Wahl, A.

    1995-10-01

    The results elaborated under the project, systems analysis of mixed radwaste disposal concepts and systems analysis of ultimate disposal concepts, provide a comprehensive description and assessment of a radwaste repository, for heat generating wastes and for wastes with negligible heat generation, and thus represent the knowledge basis for forthcoming planning work for a repository in an abandoned salt mine. A fact to be considered is that temperature field calculations have shown that there is room for further optimization with regard to the mine layout. The following aspects have been analysed: (1) safety of operation; (2) technical feasibility and realisation and licensability of the concepts; (3) operational aspects; (4) varieties of utilization of the salt dome for the intended purpose (boreholes for waste emplacement, emplacement in galleries, multi-horizon systems); (5) long-term structural stability of the mine; (6) economic efficiency; (7) nuclear materials safeguards. (orig./HP) [de

  15. Delayed breast implant reconstruction

    DEFF Research Database (Denmark)

    Hvilsom, Gitte B.; Hölmich, Lisbet R.; Steding-Jessen, Marianne

    2012-01-01

    We evaluated the association between radiation therapy and severe capsular contracture or reoperation after 717 delayed breast implant reconstruction procedures (288 1- and 429 2-stage procedures) identified in the prospective database of the Danish Registry for Plastic Surgery of the Breast during...... of radiation therapy was associated with a non-significantly increased risk of reoperation after both 1-stage (HR = 1.4; 95% CI: 0.7-2.5) and 2-stage (HR = 1.6; 95% CI: 0.9-3.1) procedures. Reconstruction failure was highest (13.2%) in the 2-stage procedures with a history of radiation therapy. Breast...... reconstruction approaches other than implants should be seriously considered among women who have received radiation therapy....

  16. Optimized molten salt receivers for ultimate trough solar fields

    Science.gov (United States)

    Riffelmann, Klaus-J.; Richert, Timo; Kuckelkorn, Thomas

    2016-05-01

    Today parabolic trough collectors are the most successful concentrating solar power (CSP) technology. For the next development step new systems with increased operation temperature and new heat transfer fluids (HTF) are currently developed. Although the first power tower projects have successfully been realized, up to now there is no evidence of an all-dominant economic or technical advantage of power tower or parabolic trough. The development of parabolic trough technology towards higher performance and significant cost reduction have led to significant improvements in competitiveness. The use of molten salt instead of synthetic oil as heat transfer fluid will bring down the levelized costs of electricity (LCOE) even further while providing dispatchable energy with high capacity factors. FLABEG has developed the Ultimate TroughTM (UT) collector, jointly with sbp Sonne GmbH and supported by public funds. Due to its validated high optical accuracy, the collector is very suitable to operate efficiently at elevated temperatures up to 550 °C. SCHOTT will drive the key-innovations by introducing the 4th generation solar receiver that addresses the most significant performance and cost improvement measures. The new receivers have been completely redesigned to provide a product platform that is ready for high temperature operation up to 550 °C. Moreover distinct product features have been introduced to reduce costs and risks in solar field assembly and installation. The increased material and design challenges incurred with the high temperature operation have been reflected in sophisticated qualification and validation procedures.

  17. Ultimate Educational Aims, Overridingness, and Personal Well-Being

    Science.gov (United States)

    Haji, Ishtiyaque; Cuypers, Stefaan E.

    2011-01-01

    Discussion regarding education's aims, especially its ultimate aims, is a key topic in the philosophy of education. These aims or values play a pivotal role in regulating and structuring moral and other types of normative education. We outline two plausible strategies to identify and justify education's ultimate aims. The first associates these…

  18. Sensitivity analysis on ultimate strength of aluminium stiffened panels

    DEFF Research Database (Denmark)

    Rigo, P.; Sarghiuta, R.; Estefen, S.

    2003-01-01

    This paper presents the results of an extensive sensitivity analysis carried out by the Committee III.1 "Ultimate Strength" of ISSC?2003 in the framework of a benchmark on the ultimate strength of aluminium stiffened panels. Previously, different benchmarks were presented by ISSC committees on ul...

  19. The importance of mines for ultimate storage at Deilmann-Haniel Shaft Sinking

    International Nuclear Information System (INIS)

    Greinacher, Jochen; Oellers, Thomas; Ahlbrecht, Thomas

    2011-01-01

    Deilmann-Haniel Shaft Sinking GmbH and its predecessor and associate companies have been involved in projects for underground ultimate storage in Germany, Europe and America for over 45 years. The field of activities previously comprised surveying, planning and sinking of shafts, repair and conversion work, design of underground sealing structures, planning of conveyors and support of the BfS in planning approval procedures. Following discontinuation of activities in the German coal mining industry the use of mines for ultimate storage is an important support for German specialist mining companies. The use of mines for ultimate storage ensures that the existing mining know how in Germany is maintained, because training of the younger generation on the commercial and engineering side of the companies is made possible by the imminent major projects.

  20. Delayed Puberty

    DEFF Research Database (Denmark)

    Kolby, Nanna; Busch, Alexander Siegfried; Juul, Anders

    2017-01-01

    . The underlying reasons for the large variation in the age at pubertal onset are not fully established; however, nutritional status and socioeconomic and environmental factors are known to be influencing, and a significant amount of influencing genetic factors have also been identified. The challenges...... optimal in discriminating especially CDGP from HH. Management of the delayed puberty depends on the etiology. For boys with CDGP an observational period will often reveal imminent puberty. If puberty is not progressing spontaneously, sex steroid replacement is effective in stimulating the development...

  1. Ultimate Lateral Capacity of Rigid Pile in c- φ Soil

    Science.gov (United States)

    Zhang, Wei-min

    2018-03-01

    To date no analytical solution of the pile ultimate lateral capacity for the general c- φ soil has been obtained. In the present study, a new dimensionless embedded ratio was proposed and the analytical solutions of ultimate lateral capacity and rotation center of rigid pile in c- φ soils were obtained. The results showed that both the dimensionless ultimate lateral capacity and dimensionless rotation center were the univariate functions of the embedded ratio. Also, the ultimate lateral capacity in the c- φ soil was the combination of the ultimate lateral capacity ( f c ) in the clay, and the ultimate lateral capacity ( f φ ) in the sand. Therefore, the Broms chart for clay, solution for clay ( φ=0) put forward by Poulos and Davis, solution for sand ( c=0) obtained by Petrasovits and Awad, and Kondner's ultimate bending moment were all proven to be the special cases of the general solution in the present study. A comparison of the field and laboratory tests in 93 cases showed that the average ratios of the theoretical values to the experimental value ranged from 0.85 to 1.15. Also, the theoretical values displayed a good agreement with the test values.

  2. The Influence of Wagon Structure Part Shape Optimization on Ultimate Fatigue Strength

    OpenAIRE

    Milovanović, Vladimir; Živković, Miroslav; Jovičić, Gordana; Živković, Jelena; Kozak, Dražan

    2016-01-01

    This study investigates how shape optimisation affects the ultimate fatigue strength of a mechanical part. The mechanical part chosen for this investigation is an axle guard of running gear elements of the Hccrrs 2x2 axle car-carrying wagon. The static and fatigue strength analysis procedure according to the UIC 517 standard and numerical methods have been applied. Material properties were determined experimentally and the necessary numerical calculations were performed by using the finite el...

  3. Ultimate guide to YouTube for business

    CERN Document Server

    2018-01-01

    Ultimate Guide to YouTube for Business helps small business owners create marketing videos to help promote their products, share their story, build a community around their brand without spending a fortune-all the while making money.

  4. Ultimate Opening Combined with Area Stability Applied to Urban Scenes

    OpenAIRE

    Marcotegui , Beatriz; Serna , Andrés; Hernández , Jorge

    2017-01-01

    International audience; This paper explores the use of ultimate opening in urban analysis context. It demonstrates the efficiency of this approach for street level elevation images, derived from 3D point clouds acquired by terrestrial mobile mapping systems. An area-stability term is introduced in the residual definition, reducing the over-segmentation of the vegetation while preserving small significant regions. We compare two possible combinations of the Ultimate Opening and the Area Stabil...

  5. Direct ultimate disposal - state of investigations and prospects

    International Nuclear Information System (INIS)

    Gasterstaedt, N.

    1991-01-01

    Based on a decision adopted by the Prime Ministers on 25/10/90, the principles governing preventive waste management of nuclear power plants are reviewed. Increasing importance is attached to the direct ultimate disposal alternative. The legal and political framework, the technology involved, the state of developments, future activities under the R and D programme as well as a cost estimate of direct ultimate disposal are presented. (orig.) [de

  6. Assessment and characterization of radioactive waste for ultimate storage

    International Nuclear Information System (INIS)

    Brennecke, P.; Warnecke, E.

    1986-01-01

    The waste specifications determined from site safety analyses define the requirements to be met by waste forms for ultimate storage. Product quality control is the process step ensuring compliance with the conditions to be met for ultimate storage. For this purpose, radionuclide inventory, fixation method, container type, waste form and quantity, and type of waste are the most significant items on the checking list. (DG) [de

  7. Ultimate - a new generation of gasoline and diesel fuels; Ultimate - eine neue Generation von Otto- und Dieselkraftstoffen

    Energy Technology Data Exchange (ETDEWEB)

    Strempel, G. [Aral Forschung/Global Fuels Technology, Bochum (Germany); Beckwith, P. [BP Fuels Management Group, Pangbourne (United Kingdom); Froehling, J. [Aral Forschung, Bochum (Germany). Labor/Analytik; Baron, U. [Aral Forschung, Bochum (Germany). Motor- und Fahrzeuglaboratorium; Sauermann, P.; Balfanz, U. [Aral Forschung, Bochum (Germany). Produktentwicklung; Doermer, W. [Aral Forschung, Bochum (Germany). Produktqualitaet

    2005-06-01

    With the launch of Ultimate 100 gasoline and Ultimate Diesel, motorists in Germany now have the opportunity to choose new advanced performance fuels designed to get the very best from their engines. This article gives details of the technical development behind these fuels, their wide range of benefits, and how it is possible to manufacture fuels which meet the considerable technical challenge of achieving both more performance and less pollution. (orig.)

  8. Ultimate strength of a large wind turbine blade

    Energy Technology Data Exchange (ETDEWEB)

    Moelholt Jensen, Find

    2008-05-15

    The present PhD project contains a study of the structural static strength of wind turbine blades loaded in flap-wise direction. A combination of experimental and numerical work has been used to address the most critical failure mechanisms and to get an understanding of the complex structural behaviour of wind turbine blades. Four failure mechanisms observed during the fullscale tests and the corresponding FE-analysis are presented. Elastic mechanisms associated with failure, such as buckling, localized bending and the Brazier effect, are studied. Six different types of structural reinforcements helping to prevent undesired structural elastic mechanisms are presented. The functionality of two of the suggested structural reinforcements was demonstrated in full-scale tests and the rest trough FE-studies. The blade design under investigation consisted of an aerodynamic airfoil and a load carrying box girder. In total, five full-scale tests have been performed involving one complete blade and two shortened box girders. The second box girder was submitted to three independent tests covering different structural reinforcement alternatives. The advantages and disadvantages of testing a shortened load carrying box girder vs. an entire blade are discussed. Changes in the boundary conditions, loads and additional reinforcements, which were introduced in the box girder tests in order to avoid undesired structural elastic mechanisms, are presented. New and advanced measuring equipment was used in the fullscale tests to detect the critical failure mechanisms and to get an understanding of the complex structural behaviour. Traditionally, displacement sensors and strain gauges in blade tests are arranged based on an assumption of a Bernoulli-Euler beam structural response. In the present study it is shown that when following this procedure important information about distortions of the cross sections is lost. In the tests presented here, one of the aims was to measure distortion

  9. Robust control of time-delay chaotic systems

    International Nuclear Information System (INIS)

    Hua Changchun; Guan Xinping

    2003-01-01

    Robust control problem of nonlinear time-delay chaotic systems is investigated. For such uncertain systems, we propose adaptive feedback controller and novel nonlinear feedback controller. They are both independent of the time delay and can render the corresponding closed-loop systems globally uniformly ultimately bounded stable. The simulations on controlling logistic system are made and the results show the controllers are feasible

  10. Ultimate load capacity assessment of reinforced concrete shell structures

    International Nuclear Information System (INIS)

    Gupta, Amita; Singh, R.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1993-01-01

    The objective of this study is to develop capability for prediction of ultimate load capacity of reinforced concrete shell structures. The present finite element code ULCA (Ultimate Load Capacity Assessment) adopts a degenerate concept of formulating general isoparametric shell element with a layered approach in the thickness direction. Different failure modes such as crushing, tensile cracking and reinforcement yielding are recognised for various problems. The structure fails by crushing of concrete when the concrete strain/stress reaches the ultimate stress or strain of concrete. Material nonlinearities as a result of tension cracking, tension stiffening between reinforcement and concrete in cracked region and yielding of reinforcement are considered along with geometric nonlinearity. Thus with this code it is possible to predict the pressure at which the first cracking, first through thickness cracking, first yielding of reinforcement occurs. After validating the code with few bench mark problems for different failure modes a reinforced concrete nuclear containment is analysed for its ultimate capacity and the results are matched with the published results. Further the ultimate load capacity of outer containment wall of Narora Atomic Power Station is predicted. It is observed that containment fails in membrane region and has a sufficient margin against design pressure. (author). 9 refs., 56 figs., 3 tabs., 1 appendix with 4 tabs

  11. Delayed Partial Nephrectomy for Hydronephrosis After Renal Trauma.

    Science.gov (United States)

    Setia, Shaan; Jackson, Jessica Nicole; Herndon, C D Anthony; Corbett, Sean T

    2017-03-01

    Delayed sequelae following conservative management of renal trauma in the pediatric population are uncommon. Reports of delayed operations to manage these sequelae are even less common. Here we present the case of a 16-year-old male patient who had delayed development of upper urinary tract obstruction with recurrent infections following high-grade renal trauma managed conservatively. Ultimately, he required a robotic-assisted partial nephrectomy 2 years after initial nonoperative management. This is unique as no prior studies to our knowledge have described delayed hydronephrosis and delayed partial nephrectomy over a year following renal trauma. Copyright © 2016 Elsevier Inc. All rights reserved.

  12. Ductility and Ultimate Capacity of Prestressed Steel Reinforced Concrete Beams

    Directory of Open Access Journals (Sweden)

    Chengquan Wang

    2017-01-01

    Full Text Available Nonlinear numerical analysis of the structural behaviour of prestressed steel reinforced concrete (PSRC beams was carried out by using finite element analysis software ABAQUS. By comparing the load-deformation curves, the rationality and reliability of the finite element model have been confirmed; moreover, the changes of the beam stiffness and stress in the forcing process and the ultimate bearing capacity of the beam were analyzed. Based on the model, the effect of prestressed force, and H-steel to the stiffness, the ultimate bearing capacity and ductility of beam were also analyzed.

  13. Ultimate load model test for Sizewell 'B' primary containment

    International Nuclear Information System (INIS)

    Crowder, R.

    1988-01-01

    This paper considers the factors influencing the adoption of an ultimate load factor for the Sizewell 'B' PWR primary containment structure. As part of the validation process for the ultimate load analysis method, a proposal has been made by Nuclear Design Associates to build and test a 1/10th scale model of the containment structure, which would proceed following the granting of section 2 consent for Sizewell 'B'. The modelling principles, construction method and test proposals are examined in some detail. The proposal is currently being considered by the CEGB's Project Management Team. (author)

  14. Ultimate pressure capacity of CANDU 6 containment structures

    International Nuclear Information System (INIS)

    Radulescu, J.P.; Pradolin, L.; Mamet, J.C.

    1997-01-01

    This paper summarizes the analytical work carried out and the results obtained when determining the ultimate pressure capacity (UPC) of the containment structures of CANDU 6 nuclear power plants. The purpose of the analysis work was to demonstrate that such containment structures are capable of meeting design requirements under the most severe accident conditions. For this concrete vessel subjected to internal pressure, the UPC was defined as the pressure causing through cracking in the concrete. The present paper deals with the overall behaviour of the containment. The presence of openings, penetrations and the ultimate pressure of the airlocks were considered separately. (author)

  15. ''Project Crystal'' for ultimate storage of highly radioactive waste

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    NAGRA (The National Association for storage of radioactive waste) in Baden has launched in North Switzerland an extensive geological research program. The current research program, under the title of ''Project Crystal'', aims at providing the scientific knowledge which is required for the assessment of the suitability of the crystalline sub-soil of North Switzerland for the ultimate storage of highly radioactive waste. Safety and feasibility of such ultimate storage are in the forefront of preoccupations. Scientific institutes of France, Germany, USA and Canada are cooperating more particularly on boring research and laboratory analyses. Technical data are given on the USA and German installations used. (P.F.K.)

  16. Trump er gældsøkonomiens ultimative illusionist

    DEFF Research Database (Denmark)

    Nielsen, Peter

    2018-01-01

    Trump giver ikke kun gevaldige skattelettelser og nærer en illusion om, at vækst vil løse alle problemer. Han fortrænger også gældsøkonomiens ultimative bundlinje i form af klimaforandringerne.......Trump giver ikke kun gevaldige skattelettelser og nærer en illusion om, at vækst vil løse alle problemer. Han fortrænger også gældsøkonomiens ultimative bundlinje i form af klimaforandringerne....

  17. Ultimate uniaxial compressive strength of stiffened panel with opening under lateral pressure

    Directory of Open Access Journals (Sweden)

    Chang-Li Yu

    2015-03-01

    Full Text Available This paper concentrated on the ultimate uniaxial compressive strength of stiffened panel with opening under lateral load and also studied the design-oriented formulae. For this purpose, three series of well executed experiments on longitudinal stiffened panel with rectangular opening subjected to the combined load have been selected as test models. The finite element analysis package, ABAQUS, is used for simulation with considering the large elasticplastic deflection behavior of stiffened panels. The feasibility of the numerical procedure is verified by a good agreement of experimental results and numerical results. More cases studies are executed employing nonlinear finite element method to analyze the influence of design variables on the ultimate strength of stiffened panel with opening under combined pressure. Based on data, two design formulae corresponding to different opening types are fitted, and accuracy of them is illustrated to demonstrate that they could be applied to basic design of practical engineering structure.

  18. Ultimate deformation capacity of reinforced concrete slabs underblast load

    NARCIS (Netherlands)

    Doormaal, J.C.A.M. van; Weerheijm, J.

    1996-01-01

    In this paper a test method to determine the deformation capacity and the resistance-deformation curve of blast-loaded slabs is described. This method was developed at TNO-PML. The method has been used to determine the ultimate deformation capacity of some simply supported reinforced concrete slabs

  19. 49 Stories That Make an Ultimate STEM Lesson Plan

    Science.gov (United States)

    Mehta, Swati; Mehta, Rohit; Berzina-Pitcher, Inese; Seals, Christopher; Mishra, Punya

    2016-01-01

    In this paper we reviewed what 49 large urban public school district STEM teachers enrolled in a year-long graduate certificate and fellowship program at a large Midwestern university considered as their amazing teaching moments. They were asked to share their amazing teaching moments that would make an Ultimate Lesson Plan in STEM. In smaller…

  20. Ultimate capabilities of soft x-ray optics

    International Nuclear Information System (INIS)

    Vinogradov, A.V.; Zorev, N.N.; Kozhevnikov, I.V.

    1988-01-01

    Nonimaging soft X-ray optics is examined. The ultimate capabilities of a number of X-ray optical components designed for concentration and collimation of radiation from point sources are determined. The applications of X-ray optics are discussed together with the properties of materials in the X-ray range

  1. Safety related aspects of ultimate disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Goemmel, R.

    1992-01-01

    Solutions and questions related to nuclear waste management are presented. In particular, long-term safety of repositories in Germany and Sweden is considered, with special attention being paid to methods of detection, geotechnical barriers and post-operational phase of salt dome repositories, and conditioning of wastes to make them fit for ultimate disposal. (DG) [de

  2. Analysis of ultimate-heat-sink spray ponds. Technical report

    International Nuclear Information System (INIS)

    Codell, R.

    1981-08-01

    This report develops models which can be utilized in the design of certain types of spray ponds used in ultimate heat sinks at nuclear power plants, and ways in which the models may be employed to determine the design basis required by U.S. Nuclear Regulatory Commission Regulatory Guide 1.27

  3. Delayed puberty in girls

    Science.gov (United States)

    ... sexual development - girls; Pubertal delay - girls; Constitutional delayed puberty ... In most cases of delayed puberty, growth changes just begin later than usual, sometimes called a late bloomer. Once puberty begins, it progresses normally. This pattern runs ...

  4. Delayed Puberty (For Teens)

    Science.gov (United States)

    ... Safe Videos for Educators Search English Español Delayed Puberty KidsHealth / For Teens / Delayed Puberty What's in this ... wonder if there's anything wrong. What Is Delayed Puberty? Puberty is the time when your body grows ...

  5. Ultimate internal pressure capacity of concrete containment structures

    International Nuclear Information System (INIS)

    Krishnaswamy, C.N.; Namperumal, R.; Al-Dabbagh, A.

    1983-01-01

    Lesson learned from the accident at Three-Mile Island nuclear plant has necessitated the computation of the ultimate internal pressure capacity of containment structures as a licensing requirement in the U.S. In general, a containment structure is designed to be essentially elastic under design accident pressure. However, as the containment pressure builds up beyond the design value due to a more severe postulated accident, the containment response turns nonlinear as it sequentially passes through cracking of concrete, yielding of linear plate, yielding of rebar, and yielding of post-tensioning tendon (if the containment concrete is prestressed). This paper reports on the determination of the ultimate internal pressure capacity and nonlinear behavior of typical reinforced and prestressed concrete BWR containments. The probable modes of failure, the criteria for ultimate pressure capacity, and the most critical sections are described. Simple equations to hand-calculate the ultimate pressure capacity and the nonlinear behavior at membrane sections of the containment shell are presented. A nonlinear finite element analysis performed to determine the nonlinear behavior of the entire shell including nonmembrane sections is briefly discribed. The analysis model consisted of laminated axisymmetric shell finite elements with nonlinear stress-strain properties for each material. Results presented for typical BWR concrete containments include nonlinear response plots of internal pressure versus containment deflection and strains in the liner, rebar, and post-tensioning tendons at the most stressed section in the shell. Leak-tightness of the containment liner and the effect of thermal loads on the ultimate capacity are discussed. (orig.)

  6. Facilitating tolerance of delayed reinforcement during functional communication training.

    Science.gov (United States)

    Fisher, W W; Thompson, R H; Hagopian, L P; Bowman, L G; Krug, A

    2000-01-01

    Few clinical investigations have addressed the problem of delayed reinforcement. In this investigation, three individuals whose destructive behavior was maintained by positive reinforcement were treated using functional communication training (FCT) with extinction (EXT). Next, procedures used in the basic literature on delayed reinforcement and self-control (reinforcer delay fading, punishment of impulsive responding, and provision of an alternative activity during reinforcer delay) were used to teach participants to tolerate delayed reinforcement. With the first case, reinforcer delay fading alone was effective at maintaining low rates of destructive behavior while introducing delayed reinforcement. In the second case, the addition of a punishment component reduced destructive behavior to near-zero levels and facilitated reinforcer delay fading. With the third case, reinforcer delay fading was associated with increases in masturbation and head rolling, but prompting and praising the individual for completing work during the delay interval reduced all problem behaviors and facilitated reinforcer delay fading.

  7. Pseudotumoral delayed cerebral radionecrosis

    International Nuclear Information System (INIS)

    Ciaudo-Lacroix, C.; Lapresle, J.

    1985-01-01

    A 60 year-old woman with a scalp epithelioma underwent radiotherapy, the dose being 57 Gray. A first epileptic seizure occurred twenty months later. Neurological examination revealed signs of left hemisphere involvement. γEG, angiography, CT scans, demonstrated a pseudotumoral avascular process. On account of the localisation, the patient being right-handed, no surgical procedure was performed. In spite of corticotherapy and anticonvulsive treatment, seizures recurred and neurological signs slowly progressed. The patient died, 22 months after the first seizure, of an associated disseminated carcinoma with cachexia. Neuropathological examination showed a massive lesion presenting all the features of delayed radionecrosis in the left hemisphere: situated mainly in the white matter; numerous vascular abnormalities; wide-spread demyelination; disappearance of oligoglial cells. The Authors recall the clinical and anatomical aspects of this condition for which the only successful treatment is surgical removal when location and size of the lesion permit. Finally, the mechanisms which have been proposed to explain this delayed cerebral radionecrosis are discussed [fr

  8. Pseudotumoral delayed cerebral radionecrosis

    Energy Technology Data Exchange (ETDEWEB)

    Ciaudo-Lacroix, C; Lapresle, J [Centre Hospitalier de Bicetre, 94 - Le Kremlin-Bicetre (France)

    1985-01-01

    A 60 year-old woman with a scalp epithelioma underwent radiotherapy, the dose being 57 Gray. A first epileptic seizure occurred twenty months later. Neurological examination revealed signs of left hemisphere involvement. ..gamma..EG, angiography, CT scans, demonstrated a pseudotumoral avascular process. On account of the localisation, the patient being right-handed, no surgical procedure was performed. In spite of corticotherapy and anticonvulsive treatment, seizures recurred and neurological signs slowly progressed. The patient died, 22 months after the first seizure, of an associated disseminated carcinoma with cachexia. Neuropathological examination showed a massive lesion presenting all the features of delayed radionecrosis in the left hemisphere: situated mainly in the white matter; numerous vascular abnormalities; wide-spread demyelination; disappearance of oligoglial cells. The Authors recall the clinical and anatomical aspects of this condition for which the only successful treatment is surgical removal when location and size of the lesion permit. Finally, the mechanisms which have been proposed to explain this delayed cerebral radionecrosis are discussed.

  9. Cable tray ultimate strength test employing a large shaker table

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, K.; Myojin, K.; Imai, K. [The Kansai Electric Power Co., Osaka (Japan); Fuyama, H. [Mitsubishi Heavy Industries Ltd, Takasago (Japan); Kokubo, E. [Mitsubishi Heavy Industdries Ltd, Kobe (Japan)

    2004-07-01

    Ultimate behaviors of cable trays, used in nuclear plants, have not been well studied since cable trays are designed based on conservative design criteria. In this study, by employing a large shaker table, an ultimate strength test was conducted for cable trays used in nuclear power plants. This report describes the results of shaker table test. The following results were obtained. First, in an S{sub 2} earthquake, the damping ratio was so large - more than 30% due to the rubbing of cables - that a large response was not present and the strains in the support were within the elastic limits. Secondly, the support was strong enough to sustain the cable trays even when the strain in the support was 20 times larger than the elastic limit. (authors)

  10. Landau damping: the mechanics model and its ultimate entropy gain

    International Nuclear Information System (INIS)

    Hannay, J H; Kluge, Michel

    2011-01-01

    Classical mechanics has only been invoked to account for Landau damping in a rather half-hearted way, alongside plasma perturbation theory. In particular this invocation is essential for the study of the saturation, or post-linear (or 'nonlinear') regime of the damping initiated by Dawson and O'Neill. By embracing mechanics wholeheartedly here, with its attendant phase space, one can access results, old and new, cleanly and directly, and with one fewer numerical integration for the post-linear regime. By using a summation technique familiar in semiclassical quantum mechanics (Poisson summation), the one remaining numerical integration can be much improved in accuracy. Also accessible from mechanics is the ultimate entropy gain. Though zero for any finite time (in the absence of coarse graining), the entropy gain is ultimately non-zero (at infinite time the required coarse graining is zero). It is calculated analytically by using the appropriate asymptotics, hitherto not fully exploited.

  11. Management and ultimate storage of wastes from nuclear power generation

    International Nuclear Information System (INIS)

    1989-09-01

    The annotation on R and D prorgam 86 parts I-II have been brought together in the present report part I, together with some general viewpoints, and been classified according to subject. Part II of the present report comprises viewpoints of 'Research Program 1987-1992' and part III of 'Alternative methods of ultimate storage'. Swedish and French viewpoints are presented in Swedish, the remaining foreign material in English. The comments are grouped in subject catergories. (O.S.)

  12. The ultimate challenge of pregnancy-associated breast carcinoma

    International Nuclear Information System (INIS)

    Raja, R.; Tahira, A.

    2005-01-01

    Pregnancy associated breast carcinoma requires making judicious use of all diagnostic modalities and the therapeutic options of surgery, irradiation, chemotherapy and hormonal therapy to enhance survival rates. Individualization of treatment for each patient is the key to success. The effects on future fertility, the time interval before next conception, and whether to breast feed or not are all well-documented. A multidisciplinary coordinated team approach to this ultimate challenge of patient care will prove fruitful. (author)

  13. Ultimate Gradient Limitation in Niobium Superconducting Accelerating Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Checchin, Mattia [Illinois Inst. of Technology, Chicago, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Grassellino, Anna [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Martinello, Martina [Illinois Inst. of Technology, Chicago, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Posen, Sam [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Romanenko, Alexander [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Zasadzinski, John [Illinois Inst. of Technology, Chicago, IL (United States)

    2016-06-01

    The present study is addressed to the theoretical description of the ultimate gradient limitation in SRF cavities. Our intent is to exploit experimental data to confirm models which provide feed-backs on how to improve the current state-of-art. New theoretical insight on the cavities limiting factor can be suitable to improve the quench field of N-doped cavities, and therefore to take advantage of high Q0 at high gradients.

  14. Ultimate capacity of piles penetrating in weak soil layers

    Directory of Open Access Journals (Sweden)

    Al-Obaidi Ahmed

    2018-01-01

    Full Text Available A pile foundation is one of the most popular forms of deep foundations. They are routinely employed to transfer axial structure loads through the soft soil to stronger bearing strata. Piles generally used to increase the load carrying capacity of the foundation and reduce the settlement of the foundation. On the other hand, many cases in practice where piles pass through different layers of soil that contain weak layers located at different depths and extension, also some time cavities with a different shape, size, and depth are found. In this study, a total of 96 cases is considered and simulated in PLAXIS 2D program aiming to understand the influence of weak soil on the ultimate pile capacity. The piles embedded in the dense sand with a layer of weak soil at different extension and location. The cross section of the geometry used in this study was designed as an axisymmetric model with the 15-node element; the boundary condition recommended at least 5D in the horizontal direction, and (L+5D in the vertical direction where D and L are the diameter and length of pile, respectively. The soil is modeled as Mohr-Coulomb, with five input parameters and the behavior of pile material represented by the linear elastic model. The results of the above cases are compared with the results found in a pile embedded in dense soil without weak layers or cavities. The results indicated that the existence of weak soil layer within the surrounding soil around the pile decreases the ultimate capacity. Furthermore, it has been found that increase in the weak soil width (extension leads to reduction in the ultimate capacity of the pile. This phenomenon is applicable to all depth of weak soil. The influence of weak layer extension on the ultimate capacity is less when it is presentin the upper soil layers.

  15. Ultimate survival in anomalous ψ(2S) decays

    International Nuclear Information System (INIS)

    Gérard, Jean-Marc; Martini, Antony

    2014-01-01

    The hierarchy among the radiative γ(π 0 ,η,η ′ ) decay channels for the ψ ′ looks quite different from the J/ψ one. The fate of charm, namely an ultimate survival of on-shell cc ¯ intermediate states, might give us the clue for this new puzzle in exclusive charmonium decays. A similar self-preservation has already been invoked in the past to solve the so-called ρπ puzzle.

  16. Ultimate concerns in late modernity: Archer, Bourdieu and reflexivity.

    Science.gov (United States)

    Farrugia, David; Woodman, Dan

    2015-12-01

    Through a critique of Margaret Archer's theory of reflexivity, this paper explores the theoretical contribution of a Bourdieusian sociology of the subject for understanding social change. Archer's theory of reflexivity holds that conscious 'internal conversations' are the motor of society, central both to human subjectivity and to the 'reflexive imperative' of late modernity. This is established through critiques of Bourdieu, who is held to erase creativity and meaningful personal investments from subjectivity, and late modernity is depicted as a time when a 'situational logic of opportunity' renders embodied dispositions and the reproduction of symbolic advantages obsolete. Maintaining Archer's focus on 'ultimate concerns' in a context of social change, this paper argues that her theory of reflexivity is established through a narrow misreading and rejection of Bourdieu's work, which ultimately creates problems for her own approach. Archer's rejection of any pre-reflexive dimensions to subjectivity and social action leaves her unable to sociologically explain the genesis of 'ultimate concerns', and creates an empirically dubious narrative of the consequences of social change. Through a focus on Archer's concept of 'fractured reflexivity', the paper explores the theoretical necessity of habitus and illusio for understanding the social changes that Archer is grappling with. In late modernity, reflexivity is valorized just as the conditions for its successful operation are increasingly foreclosed, creating 'fractured reflexivity' emblematic of the complex contemporary interaction between habitus, illusio, and accelerating social change. © London School of Economics and Political Science 2015.

  17. Speech and Language Delay

    Science.gov (United States)

    ... OTC Relief for Diarrhea Home Diseases and Conditions Speech and Language Delay Condition Speech and Language Delay Share Print Table of Contents1. ... Treatment6. Everyday Life7. Questions8. Resources What is a speech and language delay? A speech and language delay ...

  18. Delays in the management of retroperitoneal sarcomas

    DEFF Research Database (Denmark)

    Seinen, Jojanneke; Almquist, Martin; Styring, Emelie

    2010-01-01

    Retroperitoneal sarcomas are rare and treatment should optimally be centralized. Despite successful centralization with 90% of the patients referred prior to surgery, delays occur, which led us to assess lead times in a population-based series. Method. Patients diagnosed with retroperitoneal...... sarcoma in the southern Sweden health care region 2003-2009 were eligible for the study. Data on referrals and diagnostic investigations were collected from clinical files from primary health care, local hospitals, and from the sarcoma centre. Lead times were divided into patient delays and health care...... delays caused by primary health care, local hospitals, or procedures at the sarcoma centre. Results. Complete data were available from 33 patients and demonstrated a median patient delay of 23¿days (0-17¿months) and median health care delay of 94¿days (1-40¿months) with delays of median 15¿days...

  19. Methods of Synthesis of Automatic Control Systems with Delay

    Directory of Open Access Journals (Sweden)

    Aliaksandr Lapeta

    2013-05-01

    Full Text Available The paper investigates the procedure for introduction of systems containing delay elements. Shortcomings and difficulties in the synthesis of regulators and precompensators of control systems with delays in output and control channel where determined. The author focused on two approaches for the formation of promatrix and synthesis of control systems, considering the factor of delay.

  20. Rapid population growth and environmental degradation: ultimate versus proximate factors.

    Science.gov (United States)

    Shaw, R P

    1989-01-01

    This philosophical review of 2 arguments about responsibility for and solutions to environmental degradation concludes that both sides are correct: the ultimate and the proximal causes. Ultimate causes of pollution are defined as the technology responsible for a given type of pollution, such as burning fossil fuel; proximate causes are defined as situation-specific factors confounding the problem, such as population density or rate of growth. Commoner and others argue that developed countries with low or negative population growth rates are responsible for 80% of world pollution, primarily in polluting technologies such as automobiles, power generation, plastics, pesticides, toxic wastes, garbage, warfaring, and nuclear weapons wastes. Distortionary policies also contribute; examples are agricultural trade protection, land mismanagement, urban bias in expenditures, and institutional rigidity., Poor nations are responsible for very little pollution because poverty allows little waste or expenditures for polluting, synthetic technologies. The proximal causes of pollution include numbers and rate of growth of populations responsible for the pollution. Since change in the ultimate cause of pollution remains out of reach, altering the numbers of polluters can make a difference. Predictions are made for proportions of the world's total waste production, assuming current 1.6 tons/capita for developed countries and 0.17 tons/capita for developing countries. If developing countries grow at current rates and become more wealthy, they will be emitting half the world's waste by 2025. ON the other hand, unsustainable population growth goes along with inadequate investment in human capital: education, health, employment, infrastructure. The solution is to improve farming technologies in the 117 non-self-sufficient countries, fund development in the most unsustainable enclaves of growing countries, break institutionalized socio-political rigidity in these enclaves, and focus on

  1. Adobe Photoshop CS5 for Photographers The Ultimate Workshop

    CERN Document Server

    Evening, Martin

    2010-01-01

    If you already have a good knowledge of Adobe Photoshop and are looking to advance your skills, Adobe Photoshop CS5 for Photographers: The Ultimate Workshop is the book you've been waiting for.  Renowned photographers Martin Evening and Jeff Schewe impart their Photoshop tips and workflow, showing you how to use a vast array of rarely seen advanced Photoshop techniques.  Whether the subject is serious retouching work, weird and wonderful compositions, or planning a shoot before you've even picked up a camera, you can be sure that the advice is based on years of practical experience.

  2. Ultimate survival in anomalous ψ(2S) decays

    Energy Technology Data Exchange (ETDEWEB)

    Gérard, Jean-Marc; Martini, Antony

    2014-03-07

    The hierarchy among the radiative γ(π{sup 0},η,η{sup ′}) decay channels for the ψ{sup ′} looks quite different from the J/ψ one. The fate of charm, namely an ultimate survival of on-shell cc{sup ¯} intermediate states, might give us the clue for this new puzzle in exclusive charmonium decays. A similar self-preservation has already been invoked in the past to solve the so-called ρπ puzzle.

  3. Determination of Ultimate Torque for Multiply Connected Cross Section Rod

    Directory of Open Access Journals (Sweden)

    V. L. Danilov

    2015-01-01

    Full Text Available The aim of this work is to determine load-carrying capability of the multiply cross-section rod. This calculation is based on the model of the ideal plasticity of the material, so that the desired ultimate torque is a torque at which the entire cross section goes into a plastic state.The article discusses the cylindrical multiply cross-section rod. To satisfy the equilibrium equation and the condition of plasticity simultaneously, two stress function Ф and φ are introduced. By mathematical transformations it has been proved that Ф is constant along the path, and a formula to find its values on the contours has been obtained. The paper also presents the rationale of the line of stress discontinuity and obtained relationships, which allow us to derive the equations break lines for simple interaction of neighboring circuits, such as two lines, straight lines and circles, circles and a different sign of the curvature.After substitution into the boundary condition at the end of the stress function Ф and mathematical transformations a formula is obtained to determine the ultimate torque for the multiply cross-section rod.Using the doubly connected cross-section and three-connected cross-section rods as an example the application of the formula of ultimate torque is studied.For doubly connected cross-section rod, the paper offers a formula of the torque versus the radius of the rod, the aperture radius and the distance between their centers. It also clearly demonstrates the torque dependence both on the ratio of the radii and on the displacement of hole. It is shown that the value of the torque is more influenced by the displacement of hole, rather than by the ratio of the radii.For the three-connected cross-section rod the paper shows the integration feature that consists in selection of a coordinate system. As an example, the ultimate torque is found by two methods: analytical one and 3D modeling. The method of 3D modeling is based on the Nadai

  4. Bootstrap calculation of ultimate strength temperature maxima for neutron irradiated ferritic/martensitic steels

    Science.gov (United States)

    Obraztsov, S. M.; Konobeev, Yu. V.; Birzhevoy, G. A.; Rachkov, V. I.

    2006-12-01

    The dependence of mechanical properties of ferritic/martensitic (F/M) steels on irradiation temperature is of interest because these steels are used as structural materials for fast, fusion reactors and accelerator driven systems. Experimental data demonstrating temperature peaks in physical and mechanical properties of neutron irradiated pure iron, nickel, vanadium, and austenitic stainless steels are available in the literature. A lack of such an information for F/M steels forces one to apply a computational mathematical-statistical modeling methods. The bootstrap procedure is one of such methods that allows us to obtain the necessary statistical characteristics using only a sample of limited size. In the present work this procedure is used for modeling the frequency distribution histograms of ultimate strength temperature peaks in pure iron and Russian F/M steels EP-450 and EP-823. Results of fitting the sums of Lorentz or Gauss functions to the calculated distributions are presented. It is concluded that there are two temperature (at 360 and 390 °C) peaks of the ultimate strength in EP-450 steel and single peak at 390 °C in EP-823.

  5. Ultimate response time of high electron mobility transistors

    International Nuclear Information System (INIS)

    Rudin, Sergey; Rupper, Greg; Shur, Michael

    2015-01-01

    We present theoretical studies of the response time of the two-dimensional gated electron gas to femtosecond pulses. Our hydrodynamic simulations show that the device response to a short pulse or a step-function signal is either smooth or oscillating time-decay at low and high mobility, μ, values, respectively. At small gate voltage swings, U 0  = U g  − U th , where U g is the gate voltage and U th is the threshold voltage, such that μU 0 /L < v s , where L is the channel length and v s is the effective electron saturation velocity, the decay time in the low mobility samples is on the order of L 2 /(μU 0 ), in agreement with the analytical drift model. However, the decay is preceded by a delay time on the order of L/s, where s is the plasma wave velocity. This delay is the ballistic transport signature in collision-dominated devices, which becomes important during very short time periods. In the high mobility devices, the period of the decaying oscillations is on the order of the plasma wave velocity transit time. Our analysis shows that short channel field effect transistors operating in the plasmonic regime can meet the requirements for applications as terahertz detectors, mixers, delay lines, and phase shifters in ultra high-speed wireless communication circuits

  6. 75 FR 60133 - Agency Information Collection Activities: Declaration of Ultimate Consignee That Articles Were...

    Science.gov (United States)

    2010-09-29

    ... Activities: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or... the Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or...: Title: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or...

  7. The prospects of transition metal dichalcogenides for ultimately scaled CMOS

    Science.gov (United States)

    Thiele, S.; Kinberger, W.; Granzner, R.; Fiori, G.; Schwierz, F.

    2018-05-01

    MOSFET gate length scaling has been a main source of progress in digital electronics for decades. Today, researchers still spend considerable efforts on reducing the gate length and on developing ultimately scaled MOSFETs, thereby exploring both new device architectures and alternative channel materials beyond Silicon such as two-dimensional TMDs (transition metal dichalcogenide). On the other hand, the envisaged scaling scenario for the next 15 years has undergone a significant change recently. While the 2013 ITRS edition required a continuation of aggressive gate length scaling for at least another 15 years, the 2015 edition of the ITRS suggests a deceleration and eventually a levelling off of gate length scaling and puts more emphasis on alternative options such as pitch scaling to keep Moore's Law alive. In the present paper, future CMOS scaling is discussed in the light of emerging two-dimensional MOSFET channel, in particular two-dimensional TMDs. To this end, the scaling scenarios of the 2013 and 2015 ITRS editions are considered and the scaling potential of TMD MOSFETs is investigated by means of quantum-mechanical device simulations. It is shown that for ultimately scaled MOSFETs as required in the 2013 ITRS, the heavy carrier effective masses of the Mo- and W-based TMDs are beneficial for the suppression of direct source-drain tunneling, while to meet the significantly relaxed scaling targets of the 2016 ITRS heavy-effective-mass channels are not needed.

  8. The ultimate security bounds of quantum key distribution protocols

    International Nuclear Information System (INIS)

    Nikolopoulos, G.M.; Alber, G.

    2005-01-01

    Full text: Quantum key distribution (QKD) protocols exploit quantum correlations in order to establish a secure key between two legitimate users. Recent work on QKD has revealed a remarkable link between quantum and secret correlations. In this talk we report on recent results concerning the ultimate upper security bounds of various QKD schemes (i.e., the maximal disturbance up to which the two legitimate users share quantum correlations) under the assumption of general coherent attacks. In particular, we derive an analytic expression for the ultimate upper security bound of QKD schemes that use two mutually unbiased bases. As long as the two legitimate users focus on the sifted key and treat each pair of data independently during the post processing, our results are valid for arbitrary dimensions of the information carriers. The bound we have derived is well below the predictions of optimal cloning machines. The possibility of extraction of a secret key beyond entanglement distillation is also discussed. In the case of qutrits we argue that any eavesdropping strategy is equivalent to a symmetric one. For higher dimensions, however, such equivalence is generally no longer valid. (author)

  9. Ultimate internal pressure capacity assessment of SC structure

    International Nuclear Information System (INIS)

    Park, Hyungkui; Choi, Inkil

    2013-01-01

    An SC structure applied to a containment building can be quite effective. However, an SC structure cannot be applied to a containment building, because its internal pressure resistance performance has not been verified. The containment building, which undergoes ultimate internal pressure, resists the internal pressure through a pre-stress tendon. It is hard to apply a tendon to an SC structure because of its structural characteristics. Therefore, the internal pressure resistance performance of the SC structure itself should be ensured to apply it to a structure with internal pressure resistance. In this study, the suitability of an SC structure as a substitution for the tendon of a pressure resistant structure was evaluated. A containment structure model was used in this study, because it was representative structures that resistance of ultimate internal pressure be required. In this study, a nonlinear analysis was performed to evaluate and compare the behaviors of tendon model and SC structure model. By comparing the internal pressure-displacement according to the structure type, the stability of SC structure model was assessed

  10. Emergency procedures

    International Nuclear Information System (INIS)

    Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

    2004-01-01

    The following subjects are discussed - Emergency Procedures: emergency equipment, emergency procedures; emergency procedure involving X-Ray equipment; emergency procedure involving radioactive sources

  11. UAVs and Control Delays

    National Research Council Canada - National Science Library

    de Vries, S. C

    2005-01-01

    .... Delays of about 250-300 ms often lead to unacceptable airplane handling qualities. Techniques such as filtering and predictive displays may extend the range of acceptable delays up to about 400 ms...

  12. Delayed puberty in boys

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/007695.htm Delayed puberty in boys To use the sharing features on this page, please enable JavaScript. Delayed puberty in boys is when puberty does not begin ...

  13. ONE FINANCIAL REPORTING GLOBAL LANGUAGE: THE ULTIMATE GOAL?

    Directory of Open Access Journals (Sweden)

    Amelia Limijaya

    2017-05-01

    Full Text Available This article aims to analyse the extent to which international accounting standards is applied and whether it is the ultimate goal. Up until the end of 2016, approximately there are 84% of the 149 jurisdictions analysed which require IFRS for all or most domestic publicly accountable entities. This may indicate that we are not that much further from having a single set of globally-accepted accounting standards. However, there is more to financial reporting than just accounting standards alone, such as the political aspect of accounting standard-setting, translation issues surrounding IFRS adoption, the US position and the complexity of financial reporting. Improving financial reporting quality needs more than just having global accounting standards, rather, it is also essential to consider the preparers’ incentives and other institutions surrounding the firm. Stakeholders need to broaden the perspective when viewing financial reporting, so that it will not be focused merely on accounting standards alone.

  14. Multiple (Two) Met Bel 601 In Series Ultimate Vacuum Testing

    Energy Technology Data Exchange (ETDEWEB)

    Restivo, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-09-30

    SRNL Environmental and Chemical Process Technology (E&CPT) was requested to perform testing of vacuum pumps per a verbal request from the Customer, SRNL Hydrogen Processing Technology. Tritium Operations is currently having difficulties procuring the Normetex™® Model 15 m3/hr (9 CFM) vacuum pump (formerly Normetex Pompes, now EumecaSARL). One possible solution proposed by Hydrogen Processing Technology personnel is to use two Senior Aerospace Metal Bellows MB-601 vacuum pumps piped with the heads in series, and the pumps in series (Figure 1 below). This memorandum documents the ultimate vacuum testing that was performed to determine if this concept was a viable alternate vacuum pump strategy. This testing dovetails with previous pump evaluations documented in references 1 and 2.

  15. Ultimate Drivers and Proximate Correlates of Polyandry in Predatory Mites.

    Directory of Open Access Journals (Sweden)

    Peter Schausberger

    Full Text Available Polyandry is more widespread than anticipated from Bateman's principle but its ultimate (evolutionary causes and proximate (mechanistic correlates are more difficult to pinpoint than those of polygyny. Here, we combined mating experiments, quantification of reproductive traits and microsatellite genotyping to determine the fitness implications of polyandry in two predatory mite species, where males are highly polygynous (up to 45 fertilized females during life, whereas females range from monandry to various polyandry levels. The medium-level polyandrous (up to eight male mates possible Neoseiulus californicus received clear direct and indirect benefits: multiply mated females produced more offspring with higher survival chances over longer times than singly mated females. In contrast, singly and multiply mated females of the low-level polyandrous (commonly two male mates at maximum Phytoseiulus persimilis produced similar numbers of offspring having similar survival chances. In both species, multiple mating resulted in mixed offspring paternities, opening the chance for indirect fitness benefits such as enhanced genetic compatibility, complementarity and/or variability. However, the female re-mating likelihood and the paternity chance of non-first male mates were lower in P. persimilis than in N. californicus. Regarding proximate factors, in both species first mating duration and female re-mating likelihood were negatively correlated. Based on occasional fertilization failure of first male mates in P. persimilis, and mixed offspring paternities in both species, we argue that fertilization assurance and the chance to gain indirect fitness benefits are the ultimate drivers of polyandry in P. persimilis, whereas those of N. californicus are higher offspring numbers coupled with enhanced offspring viability and possibly other indirect fitness benefits. Overall, the adaptive significance and proximate events well reflected the polyandry levels. Our

  16. Ultimate Drivers and Proximate Correlates of Polyandry in Predatory Mites.

    Science.gov (United States)

    Schausberger, Peter; Patiño-Ruiz, J David; Osakabe, Masahiro; Murata, Yasumasa; Sugimoto, Naoya; Uesugi, Ryuji; Walzer, Andreas

    2016-01-01

    Polyandry is more widespread than anticipated from Bateman's principle but its ultimate (evolutionary) causes and proximate (mechanistic) correlates are more difficult to pinpoint than those of polygyny. Here, we combined mating experiments, quantification of reproductive traits and microsatellite genotyping to determine the fitness implications of polyandry in two predatory mite species, where males are highly polygynous (up to 45 fertilized females during life), whereas females range from monandry to various polyandry levels. The medium-level polyandrous (up to eight male mates possible) Neoseiulus californicus received clear direct and indirect benefits: multiply mated females produced more offspring with higher survival chances over longer times than singly mated females. In contrast, singly and multiply mated females of the low-level polyandrous (commonly two male mates at maximum) Phytoseiulus persimilis produced similar numbers of offspring having similar survival chances. In both species, multiple mating resulted in mixed offspring paternities, opening the chance for indirect fitness benefits such as enhanced genetic compatibility, complementarity and/or variability. However, the female re-mating likelihood and the paternity chance of non-first male mates were lower in P. persimilis than in N. californicus. Regarding proximate factors, in both species first mating duration and female re-mating likelihood were negatively correlated. Based on occasional fertilization failure of first male mates in P. persimilis, and mixed offspring paternities in both species, we argue that fertilization assurance and the chance to gain indirect fitness benefits are the ultimate drivers of polyandry in P. persimilis, whereas those of N. californicus are higher offspring numbers coupled with enhanced offspring viability and possibly other indirect fitness benefits. Overall, the adaptive significance and proximate events well reflected the polyandry levels. Our study provides a

  17. Delayed Orgasm and Anorgasmia

    OpenAIRE

    Jenkins, Lawrence C.; Mulhall, John P.

    2015-01-01

    Delayed orgasm/anorgasmia defined as the persistent or recurrent difficulty, delay in, or absence of attaining orgasm after sufficient sexual stimulation, which causes personal distress. Delayed orgasm and anorgasmia are associated with significant sexual dissatisfaction. A focused medical history can shed light on the potential etiologies; which include: medications, penile sensation loss, endocrinopathies, penile hyperstimulation and psychological etiologies, amongst others. Unfortunately, ...

  18. Future Synchrotron Light Sources Based on Ultimate Storage Rings

    International Nuclear Information System (INIS)

    Cai, Yunhai

    2012-01-01

    The main purpose of this talk is to describe how far one might push the state of the art in storage ring design. The talk will start with an overview of the latest developments and advances in the design of synchrotron light sources based on the concept of an 'ultimate' storage ring. The review will establish how bright a ring based light source might be, where the frontier of technological challenges are, and what the limits of accelerator physics are. Emphasis will be given to possible improvements in accelerator design and developments in technology toward the goal of achieving an ultimate storage ring. An ultimate storage ring (USR), defined as an electron ring-based light source having an emittance in both transverse planes at the diffraction limit for the range of X-ray wavelengths of interest for a scientific community, would provide very high brightness photons having high transverse coherence that would extend the capabilities of X-ray imaging and probe techniques beyond today's performance. It would be a cost-effective, high-coherence 4th generation light source, competitive with one based on energy recovery linac (ERL) technology, serving a large number of users studying material, chemical, and biological sciences. Furthermore, because of the experience accumulated over many decades of ring operation, it would have the great advantage of stability and reliability. In this paper we consider the design of an USR having 10-pm-rad emittance. It is a tremendous challenge to design a storage ring having such an extremely low emittance, a factor of 100 smaller than those in existing light sources, especially such that it has adequate dynamic aperture and beam lifetime. In many ultra-low emittance designs, the injection acceptances are not large enough for accumulation of the electron beam, necessitating on-axis injection where stored electron bunches are completely replaced with newly injected ones. Recently, starting with the MAX-IV 7-bend achromatic cell, we

  19. Future Synchrotron Light Sources Based on Ultimate Storage Rings

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yunhai; /SLAC

    2012-04-09

    The main purpose of this talk is to describe how far one might push the state of the art in storage ring design. The talk will start with an overview of the latest developments and advances in the design of synchrotron light sources based on the concept of an 'ultimate' storage ring. The review will establish how bright a ring based light source might be, where the frontier of technological challenges are, and what the limits of accelerator physics are. Emphasis will be given to possible improvements in accelerator design and developments in technology toward the goal of achieving an ultimate storage ring. An ultimate storage ring (USR), defined as an electron ring-based light source having an emittance in both transverse planes at the diffraction limit for the range of X-ray wavelengths of interest for a scientific community, would provide very high brightness photons having high transverse coherence that would extend the capabilities of X-ray imaging and probe techniques beyond today's performance. It would be a cost-effective, high-coherence 4th generation light source, competitive with one based on energy recovery linac (ERL) technology, serving a large number of users studying material, chemical, and biological sciences. Furthermore, because of the experience accumulated over many decades of ring operation, it would have the great advantage of stability and reliability. In this paper we consider the design of an USR having 10-pm-rad emittance. It is a tremendous challenge to design a storage ring having such an extremely low emittance, a factor of 100 smaller than those in existing light sources, especially such that it has adequate dynamic aperture and beam lifetime. In many ultra-low emittance designs, the injection acceptances are not large enough for accumulation of the electron beam, necessitating on-axis injection where stored electron bunches are completely replaced with newly injected ones. Recently, starting with the MAX-IV 7-bend

  20. Efficiency Of Different Teaching Models In Teaching Of Frisbee Ultimate

    Directory of Open Access Journals (Sweden)

    Žuffová Zuzana

    2015-05-01

    Full Text Available The aim of the study was to verify the efficiency of two frisbee ultimate teaching models at 8-year grammar schools relative to age. In the experimental group was used a game based model (Teaching Games for Understanding and in the control group the traditional model based on teaching techniques. 6 groups of female students took part in experiment: experimental group 1 (n=10, age=11.6, experimental group 2 (n=12, age=13.8, experimental group 3 (n=14, age =15.8, control group 1 (n=11, age =11.7, control group 2 (n=10, age =13.8 and control group 3 (n=9, age =15.8. Efficiency of the teaching models was evaluated based of game performance and special knowledge results. Game performance was evaluated by the method of game performance assessment based on GPAI (Game Performance Assessment Instrument through video record. To verify level of knowledge, we used a knowledge test, which consisted of questions related to the rules and tactics knowledge of frisbee ultimate. To perform statistical evaluation Mann-Whitney U-test was used. Game performance assessment and knowledge level indicated higher efficiency of TGfU in general, but mostly statistically insignificant. Experimental groups 1 and 2 were significantly better in the indicator that evaluates tactical aspect of game performance - decision making (p<0.05. Experimental group 3 was better in the indicator that evaluates skill execution - disc catching. The results showed that the students of the classes taught by game based model reached partially better game performance in general. Experimental groups achieved from 79.17 % to 80 % of correct answers relating to the rules and from 75 % to 87.5 % of correct answers relating to the tactical knowledge in the knowledge test. Control groups achieved from 57.69 % to 72.22 % of correct answers relating to the rules and from 51.92 % to 72.22 % of correct answers relating to the tactical knowledge in the knowledge test.

  1. Process Inherent Ultimate Safety (PIUS) reactor evaluation study: Final report

    International Nuclear Information System (INIS)

    1987-02-01

    This report presents the results of an independent study by United Engineers and Constructors (UNITED) of the SECURE-P Process Inherent Ultimate Safety (PIUS) Reactor Concept which is presently under development by the Swedish light water reactor vendor ASEA-ATOM of Vasteras, Sweden. This study was performed to investigate whether there is any realistic basis for believing that the PIUS reactor could be a viable competitor in the US energy market in the future. Assessments were limited to the technical, economic and licensing aspects of PIUS. Socio-political issues, while certainly important in answering this question, are so broad and elusive that it was considered that addressing them with the limited perspective of one small group from one company would be of questionable value and likely be misleading. Socio-political issues aside, the key issue is economics. For this reason, the specific objectives of this study were to determine if the estimated PIUS plant cost will be competitive in the US market and to identify and evaluate the technical and licensing risks that might make PIUS uneconomical or otherwise unacceptable

  2. ZIO: The Ultimate Linux I/O Framework

    CERN Document Server

    Gonzalez Cobas, J D; Rubini, A; Nellaga, S; Vaga, F

    2014-01-01

    ZIO (with Z standing for “The Ultimate I/O” Framework) was developed for CERN with the specific needs of physics labs in mind, which are poorly addressed in the mainstream Linux kernel. ZIO provides a framework for industrial, high-bandwith, high-channel count I/O device drivers (digitizers, function generators, timing devices like TDCs) with performance, generality and scalability as design goals. Among its features, it offers abstractions for • both input and output channels, and channel sets • run-time selection of trigger types • run-time selection of buffer types • sysfs-based configuration • char devices for data and metadata • a socket interface (PF ZIO) as alternative to char devices In this paper, we discuss the design and implementation of ZIO, and describe representative cases of driver development for typical and exotic applications: drivers for the FMC (FPGAMezzanine Card, see [1]) boards developed at CERN like the FMC ADC 100Msps digitizer, FMC TDC timestamp counter, and FMC DEL ...

  3. Episodic foresight and anxiety: Proximate and ultimate perspectives.

    Science.gov (United States)

    Miloyan, Beyon; Bulley, Adam; Suddendorf, Thomas

    2016-03-01

    In this paper, we examine the relationship between episodic foresight and anxiety from an evolutionary perspective, proposing that together they confer an advantage for modifying present moment decision-making and behaviour in the light of potential future threats to fitness. We review the body of literature on the role of episodic foresight in anxiety, from both proximate and ultimate perspectives. We propose that anxious feelings associated with episodic simulation of possible threat-related future events serve to imbue these simulations with motivational currency. Episodic and semantic details of a future threat may be insufficient for motivating its avoidance, but anxiety associated with a simulation can provoke adaptive threat management. As such, we detail how anxiety triggered by a self-generated, threat-related future simulation prepares the individual to manage that threat (in terms of its likelihood and/or consequences) over greater temporal distances than observed in other animals. We then outline how anxiety subtypes may represent specific mechanisms for predicting and managing particular classes of fitness threats. This approach offers an inroad for understanding the nature of characteristic future thinking patterns in anxiety disorders and serves to illustrate the adaptive function of the mechanism from which clinical anxiety deviates. © 2015 The British Psychological Society.

  4. Yield, utilization, storage and ultimate storage of depleted uranium

    International Nuclear Information System (INIS)

    Aumueller, L.; Hermann, J.

    1977-11-01

    More than 80% of the uranium leaving uranium enrichment plants is depleted to a residual content of about 0,25% U 235. Due to the present ineconomical further depletion to the technically possible residual content of 0,1% U 235, the so-called 'tails' are first of all stored. The quantity of stored depleted uranium in the FRG should be about 100.000 t by the year 2000. It represents a strategic reserve for future energy supply regardless of profitableness. The study analysis the conceivable possible uses for the tails quantity considered. These are, besides further depletion whose profitableness is considered, also the use as breeder material in breeder reactors and the use in the non-nuclear field. The main part of the study deals with the various storage possibilities of the depleted uranium in oxidic or fluoride form. A comparison of costs of alternative storage concepts showed a clear advantage for the storage of UF 6 in 48 inch containers already in use. The conceivable accidents in storing are analyzed and measures to reduce the consequences are discussed. Finally, the problems of ultimate storage for the remaining waste after further depletion or use are investigated and the costs arising here are also estimated. (RB) [de

  5. Accounting conservatism,ultimate ownership and investment efficiency

    Institute of Scientific and Technical Information of China (English)

    Xiaodong Xu; Xia Wang; Nina Han

    2012-01-01

    Purpose-The purpose of this paper is to analyze and examine the role of accounting conservatism on firm investment behavior in China.Design/methodology/approach-By combining a developed theoretical framework and empirical study,this paper examines the impacts of accounting conservatism on firm investment.The sample and data are all collected from Wind and CAMAR databases.Findings-The paper finds that the association between accounting conservatism and capital expenditure is significantly positive when inside capital is not enough to use for investment,suggesting that conservatism can expend the level of investment by decreasing information asymmetry and cost of capital;however,the association between accounting conservatism and capital expenditure is significantly negative when inside capital is enough to use for investment,suggesting that conservatism can curtail the level of investment by mitigating the interest conflicts between management and outside shareholders and decreasing agency costs.Additionally,the paper finds that the severity of information asymmetry and agency problem affects the role of accounting conservatism on firm investment behaviour,and the association between accounting conservatism and capital expenditure is weaker for firms with ultimate ownership controller as local government or individuals.Originality/value-This is the first paper to analyze and examine the impacts of accounting conservatism on firm investment in China directly.The findings are also useful to explain the awkward predicament found by prior literature.

  6. Ultimate storage of radioactive wastes annual report, 1973

    International Nuclear Information System (INIS)

    The present report is a cooperative effort by the Company for Radiation and Environmental Research, Munich, and the Company for Nuclear Research, Karlsruhe, and provides a survey of work carried out during 1973 in the area of ultimate storage of radioactive wastes. Mining and construction works which were carried out in the Asse Salt Mine near Remlingen both underground as well as above the ground and which were used for repair, maintenance and expansion of the operation consistent with its future tasks are reported. The storage of low-level wastes at the 750 m level and also the test-oriented storage of medium-level waste materials at the 490 m level were carried out within the reporting period. Shielded storage casks S7V developed by the GfK were used for the first time in September for transporting 200 l iron-hooped drums filled with medium-level radioactive wastes to Asse, each shipment always containing seven drums. With two round-trips a week taking place between the Nuclear Research Center, Karlsruhe and the Asse II shaft installation, 14 drums were brought each week so that, by the end of the year, the quantity in storage amounted to a total of 233 drums. Further information is provided concerning the present status of research work in the fields of oromechanics, geology and hydrology as well as other findings. Further, storage techniques are discussed which are presently in the planning stage

  7. Thermal performance measurements on ultimate heat sinks--cooling ponds

    International Nuclear Information System (INIS)

    Hadlock, R.K.; Abbey, O.B.

    1977-12-01

    The primary objective of the studies described is to obtain the requisite data, with respect to modeling requirements, to characterize thermal performance of heat sinks for nuclear facilities existing at elevated water temperatures in result of experiencing a genuinely large heat load and responding to meteorological influence. The data should reflect thermal performance for combinations leading to worst-case meteorological influence. A geothermal water retention basin has been chosen as the site for the first measurement program and data have been obtained in the first of several experiments scheduled to be performed there. These data illustrate the thermal and water budgets during episodes of cooling from an initially high pond water bulk temperature. Monitoring proceeded while the pond experienced only meteorological and seepage influence. The data are discussed and are presented as a data volume which may be used for calculation purposes. Suggestions for future measurement programs are stated with the intent to maintain and improve relevance to nuclear ultimate heat sinks while continuing to examine the performance of the analog geothermal pond. It is further suggested that the geothermal pond, with some modification, may be a suitable site for spray pond measurements

  8. Exploring Ultimate Water Capillary Evaporation in Nanoscale Conduits.

    Science.gov (United States)

    Li, Yinxiao; Alibakhshi, Mohammad Amin; Zhao, Yihong; Duan, Chuanhua

    2017-08-09

    Capillary evaporation in nanoscale conduits is an efficient heat/mass transfer strategy that has been widely utilized by both nature and mankind. Despite its broad impact, the ultimate transport limits of capillary evaporation in nanoscale conduits, governed by the evaporation/condensation kinetics at the liquid-vapor interface, have remained poorly understood. Here we report experimental study of the kinetic limits of water capillary evaporation in two dimensional nanochannels using a novel hybrid channel design. Our results show that the kinetic-limited evaporation fluxes break down the limits predicated by the classical Hertz-Knudsen equation by an order of magnitude, reaching values up to 37.5 mm/s with corresponding heat fluxes up to 8500 W/cm 2 . The measured evaporation flux increases with decreasing channel height and relative humidity but decreases as the channel temperature decreases. Our findings have implications for further understanding evaporation at the nanoscale and developing capillary evaporation-based technologies for both energy- and bio-related applications.

  9. Delayed orgasm and anorgasmia.

    Science.gov (United States)

    Jenkins, Lawrence C; Mulhall, John P

    2015-11-01

    Delayed orgasm/anorgasmia defined as the persistent or recurrent difficulty, delay in, or absence of attaining orgasm after sufficient sexual stimulation, which causes personal distress. Delayed orgasm and anorgasmia are associated with significant sexual dissatisfaction. A focused medical history can shed light on the potential etiologies, which include medications, penile sensation loss, endocrinopathies, penile hyperstimulation, and psychological etiologies. Unfortunately, there are no excellent pharmacotherapies for delayed orgasm/anorgasmia, and treatment revolves largely around addressing potential causative factors and psychotherapy. Copyright © 2015 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

  10. Ultimate methane yield from beef cattle manure: effect of temperature, ration constituents, antibiotics and manure age

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, A G; Varel, V H; Chen, Y R

    1981-10-01

    The effects of temperature, ration constituents, antibiotics and manure age on the ultimate methane yield (Bo, litre CH4/g volatile solids fed (VSf)) were investigated using 4-litre batch fermenters. The average Bo for fermenters maintained at 30-60 degrees Celcius (at 5 degrees Celcius intervals) was 0.328 litre CH4/g VSf. The Bo at 65 degrees Celcius averaged 0.118 litre CH4g VSf, but this low yield was attributed to unstable fermentation rather than decreased substrate availability at that temperature. These results agreed well with Bo values estimated from daily-fed fermenters. Chlortetracycline and monensin did not affect Bo; however, monensin did delay the start of active fermentation in batch fermenters. The average Bo of manure from cattle fed 91.5, 40 and 7% corn silage were 0.173, 0.232 and 0.290 litre CH4/g VSf, respectively. The average Bo for 6-8 week old manure from a dirt feedlot was 0.210 litre CH4/g VSf. (Refs. 14).

  11. Ultimate resistance of a reinforced concrete foundation under impulsive loading

    International Nuclear Information System (INIS)

    Aquaro, D.; Forasassi, G.; Marconi, M.

    2003-01-01

    The impact of a spent nuclear fuel cask against a reinforced concrete slab of a temporary repository for spent nuclear fuel is numerically analysed. The analysis considers accidental events in which a spent nuclear fuel cask would drop against the floor of a repository during lifting operations. Two types of solutions have been taken into account: a simple reinforced concrete structure and a structure provided with a 40 mm thick steel liner on the impacted surface, connected to a 1600 mm thick concrete bed. The model is assumed to be axisymmetric and positioned on an elastic ground (Winkler model). The concrete has been simulated as: elastic perfectly plastic under compressive stresses limited by a crushing strain; elastic linear under tensile stresses until a cracking stress value and a following decrease of stress characterized by a constant or variable softening modulus; limited ability to resist at shear stresses after cracking characterized by a shear retention factor. The steel of the reinforcement bars and of the cask has been simulated as an elastic perfectly plastic material. Several numerical simulations have been performed in order to determine the influence, on the ultimate resistance of the structure under examination, of the steel liner, of some characteristic parameters of concrete (as the softening module and the shear retention factor) and of the Winkler coefficient values, simulating the elastic behaviour of the ground. The obtained results demonstrate that a steel liner produces a lower stress in the concrete as well as in the reinforcement but the bed is still subjected to the cracking phenomenon throughout its entire width although the crushing is localized to only a few elements near the impact zone. The use of a more complex constitutive equation for the concrete considering the shear retention factor and the softening module has given results which do not differ greatly from those related to a more simplified model. A different degree of

  12. American Dream Delayed

    DEFF Research Database (Denmark)

    Khorunzhina, Natalia; Miller, Robert A.

    This paper investigates the delay in homeownership and a subsequent reduction in homeownership rate observed over the past decades. We focus on the delay in giving birth to children and increased labor market participation as contributing factors to homeownership dynamics for prime-age female hou...

  13. Radiochemical Means of Investigating Delayed Neutron Precursors

    International Nuclear Information System (INIS)

    Marmol, P. del

    1968-01-01

    Fast radiochemical methods used now for the determination of delayed neutron precursors are classified and reviewed: precipitations, solvent extractions, range experiments, milking, gas sweeping, isotopic and ion exchange, hot atom reactions and diffusion loss. Advantages and limitations of irradiation systems with respect to fast separations are discussed: external beams which allow faster separations only have low neutron fluxes, internal beams which are mostly fit for gaseous reactions; and rabbits for solution irradiations. Future prospects of radiochemical procedures are presented; among these, studies should be mostly oriented towards gaseous reactions which offer possibilities of isolating very short-lived delayed neutron precursors. Chemical procedures for delayed neutron precursor detection are compared with mass spectrometric and isotope separator techniques; it is concluded that the methods are complementary. (author)

  14. Radiochemical Means of Investigating Delayed Neutron Precursors

    International Nuclear Information System (INIS)

    Marmol, P. del

    1968-01-01

    Fast radiochemical methods used now for the determination of delayed neutron precursors are classified and reviewed: precipitations, solvent extractions, range experiments, milking, gas sweeping, isotopic and ion exchange, hot-atom reactions and diffusion loss. Advantages and limitations of irradiation systems with respect to fast separations are discussed: external beams which allow faster separations only have low neutron fluxes, internal beams which are mostly fit for gaseous reactions; and rabbits for solution irradiations. Future prospects of radiochemical procedures are presented; among these, studies should be mostly oriented towards gaseous reactions which offer possibilities of isolating very short-lived delayed neutron precursors. Chemical procedures for delayed neutron precursor detection are compared with mass spectrometric and isotope-separator techniques; it is concluded that the methods are complementary. (author)

  15. Delays in the operating room: signs of an imperfect system.

    Science.gov (United States)

    Wong, Janice; Khu, Kathleen Joy; Kaderali, Zul; Bernstein, Mark

    2010-06-01

    Delays in the operating room have a negative effect on its efficiency and the working environment. In this prospective study, we analyzed data on perioperative system delays. One neurosurgeon prospectively recorded all errors, including perioperative delays, for consecutive patients undergoing elective procedures from May 2000 to February 2009. We analyzed the prevalence, causes and impact of perioperative system delays that occurred in one neurosurgeon's practice. A total of 1531 elective surgical cases were performed during the study period. Delays were the most common type of error (33.6%), and more than half (51.4%) of all cases had at least 1 delay. The most common cause of delay was equipment failure. The first cases of the day and cranial cases had more delays than subsequent cases and spinal cases, respectively. A delay in starting the first case was associated with subsequent delays. Delays frequently occur in the operating room and have a major effect on patient flow and resource utilization. Thorough documentation of perioperative delays provides a basis for the development of solutions for improving operating room efficiency and illustrates the principles underlying the causes of operating room delays across surgical disciplines.

  16. R&D paths toward achieving ultimate capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Peter Kneisel

    2004-09-01

    Superconducting niobium cavities for particle accelerator application are performing nowadays better than ever and a series of procedures have been established--if applied properly--which will result in multi-cell cavity gradients of up to E{sub acc} = 35 MV/m, the design goal for the International Linear Collider (ILC). In several cases gradients above 40 MV/m have been measured in single cell tests. These gradients are close to or at the critical magnetic field value for niobium--at least what is believed to be the fundamental limitation of the material. However, there are still some open questions, whether the value for the superheated magnetic field of {approx} 180 mT is the final answer.

  17. A Delay Discounting Model of Psychotherapy Termination

    Science.gov (United States)

    Swift, Joshua K.; Callahan, Jennifer L.

    2009-01-01

    Delay discounting (DD) procedures are emerging as an important new method for psychotherapy researchers. In this paper a framework for conceptualizing existing, seemingly discrepant, research findings on termination is introduced and new directions for research are described. To illustrate the value of a DD framework, the common psychotherapy…

  18. Medicare program; update of ratesetting methodology, payment rates, payment policies, and the list of covered procedures for ambulatory surgical centers effective October 1, 1998; reopening of comment period and delay in adoption of the proposed rule as final--HCFA. Notice of reopening of comment period for proposed rule and delay in adoption of provisions of the proposed rule as final.

    Science.gov (United States)

    1998-10-01

    This notice reopens the comment period for a proposed rule affecting Medicare payments to ambulatory surgical centers (ASCs) that was originally published in the Federal Register on June 12, 1998 (63 FR 32290). This document gives notice of a delay in the adoption of the provisions of the June 12, 1998 ASC proposed rule as a final rule to be concurrent with the adoption as final of the hospital outpatient prospective payment system (PPS) that is the subject of a proposed rule published in the Federal Register on September 8, 1998 (63 FR 47551). In addition this document confirms that the current ASC payment rates that are effective for services furnished on or after October 1, 1998, will remain in effect until rebased ASC rates and the provisions of the June 12, 1998 ASC proposed rule are adopted as final to be concurrent with the adoption as final of the Medicare hospital PPS.

  19. Measurement of ultimate tensile strength and Young modulus in LYSO scintillating crystals

    Energy Technology Data Exchange (ETDEWEB)

    Scalise, Lorenzo, E-mail: l.scalise@univpm.it [Dipartimento di Meccanica, Universita Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Rinaldi, Daniele [Dipartimento di Fisica e Ingegneria dei Materiali e del Territorio, Universita Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Istituto Nazionale di Fisica Nucleare, Section of Perugia (Italy); Davi, Fabrizio [Dipartimento di Architettura Costruzioni e Strutture, Universita Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Paone, Nicola [Dipartimento di Meccanica, Universita Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy)

    2011-10-21

    Scintillating crystals are employed in high energy physics, in medical imaging, diagnostic and security. Two mechanical properties of lutetium-yttrium oxyorthosilicate cerium-doped Lu{sub 2(1-x)}Y{sub 2x}SiO{sub 5}:Ce with x=0.1 (LYSO) crystals have been measured: the ultimate tensile stress ({sigma}{sub UTS}) and the Young elastic modulus (E). Measurements are made by means of a 4-points loading device and the experimental results account for an elastic-brittle stress-strain relation, which depends heavily on the specimen preparation and the material defects. {sigma}{sub UTS} along the [0 1 0] tensile direction ranges within 68.14 and 115.61 MPa, which, in the lowest case, is more than twice with respect to those measured for PbWO{sub 4} (PWO), exhibiting a marked difference between the annealed and the not-annealed samples. The mean elastic modulus (E), along the same direction, is E=1.80x10{sup 11} ({+-}2.15x10{sup 10}) N/m{sup 2}, with lower dispersion respect to UTS data. This type of analysis and study can be included into quality control procedures of crystals, based on samples taken out of production; such procedures can be established for industrial processing of crystals aimed to the high energy physics (calorimeters) and medical imaging (PET, etc.) applications.

  20. The effects of local nitroglycerin on the surgical delay procedure in prefabricated flaps by vascular implant in rats Efeitos da nitroglicerina tópica na autonomização de retalhos pré-fabricados por implante vascular em ratos

    Directory of Open Access Journals (Sweden)

    Jairo Zacchê de Sá

    2012-12-01

    Full Text Available PURPOSE: To evaluate the effect of local nitroglycerin on the viable area of a prefabricated flap for vascular implant in rats, and to investigate the surgical delay procedure. METHODS: A femoral pedicle was implanted under the skin of the abdominal wall in forty Wistar rats. The animals were divided into four groups of ten: group 1 - without surgical delay procedure and local nitroglycerin; group 2 - with surgical delay procedure, but without local nitroglycerin; group 3 - without surgical delay procedure, but with local nitroglycerin; and group 4 - with simultaneous surgical delay procedure and local nitroglycerin. The percentages of the viable areas, in relation to the total flap, were calculated using AutoCAD R 14. RESULTS: The mean percentage value of the viable area was 8.9% in the group 1. 49.4% in the group 2; 8.4% in the group 3 and 1.1% in the group 4. There was significant difference between groups 1 and 2 (p=0.005, 1 and 4 (p=0.024, 2 and 3 (p=0.003, 2 and 4 (p=0.001. These results support the hypothesis that the closure of the arterial venous channels is responsible for the phenomenon of surgical delay procedure. CONCLUSION: Local nitroglycerin did not cause an increase in the prefabricated viable flap area by vascular implantation and decreased the viable flap area that underwent delay procedures.OBJETIVO: Avaliar o efeito da nitroglicerina tópica sobre a área viável de um modelo de retalho pré-fabricado por implante vascular em ratos e analisar o mecanismo de autonomização cirúrgica aplicada a retalhos pré-fabricados. MÉTODOS: Foram utilizados 40 ratos Wistar. No primeiro tempo cirúrgico - 20 ratos foram submetidos a implante do pedículo femoral na região subdérmica da parede abdominal, e 20 submetidos à autonomização cirúrgica de retalho cutâneo de parede abdominal e, simultaneamente, implante do pedículo femoral na região subdérmica deste retalho. No segundo tempo - após três semanas e em todos os animais

  1. 78 FR 69101 - Agency Information Collection Activities: Declaration of the Ultimate Consignee That Articles...

    Science.gov (United States)

    2013-11-18

    ... Activities: Declaration of the Ultimate Consignee That Articles Were Exported for Temporary Scientific or... the Declaration of the Ultimate Consignee that Articles were Exported for Temporary Scientific or...: Title: Declaration of the Ultimate Consignee that Articles were Exported for Temporary Scientific or...

  2. Delayed power analysis

    International Nuclear Information System (INIS)

    Adamovich, L.A.; Azarov, V.V.

    1999-01-01

    Time dependent core power behavior in a nuclear reactor is described with well-known neutron kinetics equations. At the same time, two portions are distinguished in energy released from uranium nuclei fission; one released directly at fission and another delayed (residual) portion produced during radioactive decay of fission products. While prompt power is definitely described with kinetics equations, the delayed power presentation still remains outstanding. Since in operation the delayed power part is relatively small (about 6%) operation, it can be neglected for small reactivity disturbances assuming that entire power obeys neutron kinetics equations. In case of a high negative reactivity rapidly inserted in core (e.g. reactor scram initiation) the prompt and delayed components can be calculated separately with practically no impact on each other, employing kinetics equations for prompt power and known approximation formulas for delayed portion, named residual in this specific case. Under substantial disturbances the prompt component in the dynamic process becomes commensurable with delayed portion, thus making necessary to take into account their cross impact. A system of differential equations to describe time-dependent behavior of delayed power is presented. Specific NPP analysis shows a way to significantly simplify the task formulation. (author)

  3. The establishment of MELCOR/SNAP model of Chinshan nuclear power plant for Ultimate Response Guideline

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Wen-Sheng, E-mail: wshsu@ess.nthu.edu.tw [Nuclear Science and Technology Development Center, Institute of Nuclear Engineering and Science, National Tsing Hua University, Nuclear and New Energy Education and Research Foundation, No. 101, Section 2, Kuang Fu Rd., HsinChu 30013, Taiwan, ROC (China); Chiang, Yu, E-mail: s101013702@m101.nthu.edu.tw [Nuclear Science and Technology Development Center, Institute of Nuclear Engineering and Science, National Tsing Hua University, Nuclear and New Energy Education and Research Foundation, No. 101, Section 2, Kuang Fu Rd., HsinChu 30013, Taiwan, ROC (China); Wang, Jong-Rong, E-mail: jongrongwang@gmail.com [Nuclear Science and Technology Development Center, Institute of Nuclear Engineering and Science, National Tsing Hua University, Nuclear and New Energy Education and Research Foundation, No. 101, Section 2, Kuang Fu Rd., HsinChu 30013, Taiwan, ROC (China); Wang, Ting-Yi, E-mail: minired1119@gmail.com [Nuclear Science and Technology Development Center, Institute of Nuclear Engineering and Science, National Tsing Hua University, Nuclear and New Energy Education and Research Foundation, No. 101, Section 2, Kuang Fu Rd., HsinChu 30013, Taiwan, ROC (China); Wang, Te-Chuan, E-mail: tcwang@iner.gov.tw [Institute of Nuclear Energy Research Atomic Energy Council, R.O.C., 1000, Wenhua Road Jiaan Village, Longtan Township, Taoyuan County 32546, Taiwan (China); Teng, Jyh-Tong, E-mail: jyhtong@cycu.edu.tw [Department of Mechanical Engineering, Chung Yuan Christian University, 200, Chung Pei Rd, Chung Li 32023, Taiwan, ROC (China); Chen, Shao-Wen, E-mail: chensw@mx.nthu.edu.tw [Nuclear Science and Technology Development Center, Institute of Nuclear Engineering and Science, National Tsing Hua University, Nuclear and New Energy Education and Research Foundation, No. 101, Section 2, Kuang Fu Rd., HsinChu 30013, Taiwan, ROC (China); and others

    2017-01-15

    Highlights: • The establishment of a MELCOR/SNAP model of Chinshan (BWR/4). • MELCOR/SNAP model was used to estimate the effectiveness of URG for Chinshan. • The MELCOR results were compared to MAAP, TRACE and PCTRAN. • URG is a new method to prevent a Fukushima-like accident. • The low raw water (150 GPM) can make the cladding temperature below 1088.7 K. - Abstract: After Fukushima Daiichi disaster, the safety analysis of severe accidents became one of the safety concerns in Taiwan. The Emergency Operating Procedure (EOP) cannot cope with a multiple system failure situation under a severe accident since it is a “Symptom-basis” procedure. To deal with that, Taiwan Power Company built up a new strategy for Fukushima-like accident called Ultimate Response Guideline (URG). It is a simple strategy with three main conditions: loss of regular motor driven injection system, loss of all AC power and tsunami/earthquake warning. If two of three happen, the operating procedure will change from EOP to URG and start the main works by following the strategy. There are three main works in URG: controlled-depressurization, line up low pressure injection water and prepare containment venting. In this study, MELCOR2.1 was used to calculate the cases of URG and checked the goal of the strategy that prevents the accident or not. There were three steps in this research. First, a model of Chinshan nuclear power plant (NPP) was built. Second, one was the case with URG and the other was not by using the above MELCOR model. The results were compared to MAAP5.0, TRACE and PCTRAN. Finally, some sensitivity studies of depressurization and water injection rate were done.

  4. BOOK REVIEW: Seeking Ultimates. An Intuitive Guide to Physics

    Science.gov (United States)

    Brown, Neil

    2000-05-01

    Physics has the reputation of being a difficult and dry subject. Many books have been written in attempts to show that the difficulties are not insurmountable, even for the layman, and to convey some of the fascination it provides for those within it. In Seeking Ultimates Peter Landsberg avoids mathematics, the source of so many difficulties, entirely, and seeks to make physics comprehensible by what he terms intuition. He also emphasizes that there is almost no part of science that is completely understood; there are always areas of incompleteness and uncertainty, capable of providing exciting new results, and examples of this are highlighted throughout the book. After an introduction Landsberg starts with macroscopic phenomena for ease of understanding, though one might question whether the chosen topic of thermodynamics is ever going to be easy. Next he looks at microscopic effects, from atomic structure to the fundamental particles of the standard model and their interactions. There follow chapters on time and entropy, on chaos theory, on quantum mechanics and then cosmology. The final chapters look at physical constants (including the anthropic principle), whether physics has room for a creator God (the conclusion is that this is not the province of science), and some thoughts on science as a human activity. The chosen topics are those which have been important in the late twentieth century and remain important. Each chapter cites an eminent scientist as a `hero', though little is made of this. There are occasional historical notes, set in boxes, and a few short poems to leaven the text. What the book achieves is difficult to assess. Removing mathematics and adding a glossary of technical terms do not necessarily allow non-scientists to enjoy the text, as the publisher's note on the back cover suggests. The concepts can baffle the layman even more than the mathematics, and one of the most difficult of all physical concepts permeates so much of this book

  5. Delayed interval delivery in twin pregnancy without cerclage: Case ...

    African Journals Online (AJOL)

    After the loss of the first foetus, delayed delivery in multiple pregnancies can be successful in selected cases as exemplified by the case presentation. In well prepared perinatal centers, with physically and psychologically balanced patients who are well informed about the risks and benefits of the procedure, delayed interval ...

  6. Neutron delayed choice experiments

    International Nuclear Information System (INIS)

    Bernstein, H.J.

    1986-01-01

    Delayed choice experiments for neutrons can help extend the interpretation of quantum mechanical phenomena. They may also rule out alternative explanations which static interference experiments allow. A simple example of a feasible neutron test is presented and discussed. (orig.)

  7. Quad nanosecond delay module

    International Nuclear Information System (INIS)

    McDonald, R.J.; Hunter, J.B.; Wozniak, G.J.

    1986-04-01

    Four nanosecond (ns) delay units have been designed to fit in a single-width NIM module. This module is particularly suited for use in conjunction with quad constant fraction timing discriminators (CFTDs) since it has four delay units that can be placed adjacent to the four units of the CFTD. A series of different length cables connected via DIP toggle switches provide delays of 0.60 ns in 4 ns increments. Thus, the CFTD delay can be optimized for pulses of different rise times from approx.10-100 ns. Design work for the PC board and silkscreening of the front panel were done with the MacDraw program on the Apple Mackintosh computer and printed with the Lasewriter printer. 6 refs

  8. Delayed rule following

    OpenAIRE

    Schmitt, David R.

    2001-01-01

    Although the elements of a fully stated rule (discriminative stimulus [SD], some behavior, and a consequence) can occur nearly contemporaneously with the statement of the rule, there is often a delay between the rule statement and the SD. The effects of this delay on rule following have not been studied in behavior analysis, but they have been investigated in rule-like settings in the areas of prospective memory (remembering to do something in the future) and goal pursuit. Discriminative even...

  9. Vernier Delay Unit

    International Nuclear Information System (INIS)

    Pierce, W.B.

    1984-10-01

    This module will accept differential ECL pulses from the auxiliary rear panel or NIM level pulses from the front panel. The pulses are produced at the output with a fixed delay that is software programmable in steps of 0.1 ns over the range of 0.1 to 10.5 ns. Multiple outputs are available at the front panel. Minimum delay through the module is 9 ns

  10. Quad precision delay generator

    International Nuclear Information System (INIS)

    Krishnan, Shanti; Gopalakrishnan, K.R.; Marballi, K.R.

    1997-01-01

    A Quad Precision Delay Generator delays a digital edge by a programmed amount of time, varying from nanoseconds to microseconds. The output of this generator has an amplitude of the order of tens of volts and rise time of the order of nanoseconds. This was specifically designed and developed to meet the stringent requirements of the plasma focus experiments. Plasma focus is a laboratory device for producing and studying nuclear fusion reactions in hot deuterium plasma. 3 figs

  11. Modelling delays in pharmacokinetics

    International Nuclear Information System (INIS)

    Farooqi, Z.H.; Lambrecht, R.M.

    1990-01-01

    Linear system analysis has come to form the backbone of pharmacokinetics. Natural systems usually involve time delays, thus models incorporating them would be an order closer approximation to the real world compared to those that do not. Delays may be modelled in several ways. The approach considered in this study is to have a discrete-time delay dependent rate with the delay respresenting the duration between the entry of a drug into a compartment and its release in some form (may be as a metabolite) from the compartment. Such a delay may be because of one or more of several physiological reasons, like, formation of a reservoir, slow metabolism, or receptor binding. The mathematical structure this gives rise to is a system of delay-differential equations. Examples are given of simple one and two compartment systems with drugs like bumetanide, carbamazepine, and quinolone-caffeine interaction. In these examples generally a good fit is obtained and the suggested models form a good approximation. 21 refs., 6 figs

  12. Ultimate disposal of radioactive waste in the FRG - current progress of projects and perspectives

    International Nuclear Information System (INIS)

    Roesel, H.

    1989-01-01

    In the Federal Republic of Germany, the state is responsible for providing for the ultimate disposal of radioactive waste, whereas the cost is borne by the waste producing establishments. The Federal Ministry for the Environment, Nature Conservation and Reactor Safety, (BMU), as the competent state authority has delegated its responsibilities in this matter to the Physikalisch-Technische Bundesanstalt (PTB). The PTB is allowed to have work done by third parties. For this purpose, the Deutsche Gesellschaft zum Bau und Betrieb von Endlagern fuer Abfallstoffe mbH (DBE) has been founded, which since 1979 is investigating the Gorleben salt dome for suitability to serve as a repository for all type of solid, radioactive waste. The final decisions on site approval can be taken after completion of the underground exploration work, which according to current schedules is expected to be achieved at the end of the 1990s. The other candidate site, the Konrad mine, has been investigated by the GSF in the years 1976 to 1982, and on August 31, 1982 the PTB has filed an application to institute the plan approval procedure for the Konrad mine to be prepared to serve as a waste repository. The plan is expected to be laid open in the first half of 1989, and hearings possibly be held in the second half. In case of plan approval, the site preparation will probably take 3 years, so that the Konrad mine will be ready to receive radioactive waste by the year 1993. (orig.) [de

  13. A hybrid approach to parameter identification of linear delay differential equations involving multiple delays

    Science.gov (United States)

    Marzban, Hamid Reza

    2018-05-01

    In this paper, we are concerned with the parameter identification of linear time-invariant systems containing multiple delays. The approach is based upon a hybrid of block-pulse functions and Legendre's polynomials. The convergence of the proposed procedure is established and an upper error bound with respect to the L2-norm associated with the hybrid functions is derived. The problem under consideration is first transformed into a system of algebraic equations. The least squares technique is then employed for identification of the desired parameters. Several multi-delay systems of varying complexity are investigated to evaluate the performance and capability of the proposed approximation method. It is shown that the proposed approach is also applicable to a class of nonlinear multi-delay systems. It is demonstrated that the suggested procedure provides accurate results for the desired parameters.

  14. Optimal Joint Expected Delay Forwarding in Delay Tolerant Networks

    OpenAIRE

    Jia Xu; Xin Feng; Wen Jun Yang; Ru Chuan Wang; Bing Qing Han

    2013-01-01

    Multicopy forwarding schemes have been employed in delay tolerant network (DTN) to improve the delivery delay and delivery rate. Much effort has been focused on reducing the routing cost while retaining high performance. This paper aims to provide an optimal joint expected delay forwarding (OJEDF) protocol which minimizes the expected delay while satisfying a certain constant on the number of forwardings per message. We propose a comprehensive forwarding metric called joint expected delay (JE...

  15. Research On Variable-Length Transfer Delay and Delayed Signal Cancellation Based PLLs

    DEFF Research Database (Denmark)

    Golestan, Saeed; Guerrero, Josep M.; Quintero, Juan Carlos Vasquez

    2018-01-01

    large frequency drifts are anticipated and a high accuracy is required. To the best of authors' knowledge, the small-signal modeling of a variable-length delay-based PLL has not yet been conducted. The main aim of this paper is to cover this gap. The tuning procedure and analysis of these PLLs...

  16. 75 FR 80536 - Procedures for the Surrender of Unwanted Controlled Substances by Ultimate Users; Notice of Meeting

    Science.gov (United States)

    2010-12-22

    ... third parties to express their views at the meeting or by written comment concerning the most safe and... 2006. Teens abuse prescription drugs more than any illicit drug except marijuana--more than cocaine...

  17. 75 FR 32273 - Representation Election Procedure

    Science.gov (United States)

    2010-06-08

    ... Representation Election Procedure AGENCY: National Mediation Board. ACTION: Final rule; delay of effective date. SUMMARY: The National Mediation Board (NMB) is delaying the effective date of its rule regarding... participants under the Railway Labor Act (RLA) that the rule will apply to applications filed on or after June...

  18. Quantization Procedures

    International Nuclear Information System (INIS)

    Cabrera, J. A.; Martin, R.

    1976-01-01

    We present in this work a review of the conventional quantization procedure, the proposed by I.E. Segal and a new quantization procedure similar to this one for use in non linear problems. We apply this quantization procedures to different potentials and we obtain the appropriate equations of motion. It is shown that for the linear case the three procedures exposed are equivalent but for the non linear cases we obtain different equations of motion and different energy spectra. (Author) 16 refs

  19. Energy management - The delayed flap approach

    Science.gov (United States)

    Bull, J. S.

    1976-01-01

    Flight test evaluation of a Delayed Flap approach procedure intended to provide reductions in noise and fuel consumption is underway using the NASA CV-990 test aircraft. Approach is initiated at a high airspeed (240 kt) and in a drag configuration that allows for low thrust. The aircraft is flown along the conventional ILS glide slope. A Fast/Slow message display signals the pilot when to extend approach flaps, landing gear, and land flaps. Implementation of the procedure in commercial service may require the addition of a DME navigation aid co-located with the ILS glide slope transmitter. The Delayed Flap approach saves 250 lb of fuel over the Reduced Flap approach, with a 95 EPNdB noise contour only 43% as large.

  20. Assessing delay discounting in mice

    OpenAIRE

    Mitchell, Suzanne H.

    2014-01-01

    Delay discounting (also intertemporal choice or impulsive choice) is the process by which delayed outcomes, such as delayed food delivery, are valued less than the same outcomes delivered immediately or with a shorter delay. This process is of interest because many psychopathologies, including substance dependence, pathological gambling, attention deficit hyperactivity disorder and conduct disorder, are characterized by heightened levels of delay discounting. Some of these disorders are herit...

  1. Ultimate architecture

    CERN Multimedia

    Jencks, Charles

    2007-01-01

    "European physics hothouse CERN recently unveiled Atlas, the world's most powerful particle detector, which it will use to search for the fundamental building blocks of nature from May next year. Charles Jencks describes the experience of getting up clsoe to the engineering marvel that could en up creating a mini-black hole."(5 pages with photos).

  2. Ultimate energy

    International Nuclear Information System (INIS)

    1994-01-01

    An explanation is given of the complexity faced by the scientific researcher in an effort to achieve fusion power. Outlines the theory and current experiments being pursued in this complex project, including visits to five major fusion research laboratories, and interviews with physicists

  3. Estimating Delays In ASIC's

    Science.gov (United States)

    Burke, Gary; Nesheiwat, Jeffrey; Su, Ling

    1994-01-01

    Verification is important aspect of process of designing application-specific integrated circuit (ASIC). Design must not only be functionally accurate, but must also maintain correct timing. IFA, Intelligent Front Annotation program, assists in verifying timing of ASIC early in design process. This program speeds design-and-verification cycle by estimating delays before layouts completed. Written in C language.

  4. Permissible Delay in Payments

    Directory of Open Access Journals (Sweden)

    Yung-Fu Huang

    2007-01-01

    Full Text Available The main purpose of this paper wants to investigate the optimal retailer's lot-sizing policy with two warehouses under partially permissible delay in payments within the economic order quantity (EOQ framework. In this paper, we want to extend that fully permissible delay in payments to the supplier would offer the retailer partially permissible delay in payments. That is, the retailer must make a partial payment to the supplier when the order is received. Then the retailer must pay off the remaining balance at the end of the permissible delay period. In addition, we want to add the assumption that the retailer's storage space is limited. That is, the retailer will rent the warehouse to store these exceeding items when the order quantity is larger than retailer's storage space. Under these conditions, we model the retailer's inventory system as a cost minimization problem to determine the retailer's optimal cycle time and optimal order quantity. Three theorems are developed to efficiently determine the optimal replenishment policy for the retailer. Finally, numerical examples are given to illustrate these theorems and obtained a lot of managerial insights.

  5. Delayed neutrons in ANSTO

    International Nuclear Information System (INIS)

    Wall, T.

    1988-01-01

    Delayed neutron analysis carried out at the Australian Nuclear Scientific and Technology Organization facilities, provides a fast, high sensitivity, low cost, reliable method, particularly suitable for large batches of samples, and for non destructive analysis of a range of materials. While its main use has been in uranium exploration, other applications include archeological investigations, agriculture, oceanography and biology

  6. Development of a statistically based access delay timeline methodology.

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, W. Gary; Robinson, David Gerald; Wyss, Gregory Dane; Hendrickson, Stacey M. Langfitt

    2013-02-01

    The charter for adversarial delay is to hinder access to critical resources through the use of physical systems increasing an adversarys task time. The traditional method for characterizing access delay has been a simple model focused on accumulating times required to complete each task with little regard to uncertainty, complexity, or decreased efficiency associated with multiple sequential tasks or stress. The delay associated with any given barrier or path is further discounted to worst-case, and often unrealistic, times based on a high-level adversary, resulting in a highly conservative calculation of total delay. This leads to delay systems that require significant funding and personnel resources in order to defend against the assumed threat, which for many sites and applications becomes cost prohibitive. A new methodology has been developed that considers the uncertainties inherent in the problem to develop a realistic timeline distribution for a given adversary path. This new methodology incorporates advanced Bayesian statistical theory and methodologies, taking into account small sample size, expert judgment, human factors and threat uncertainty. The result is an algorithm that can calculate a probability distribution function of delay times directly related to system risk. Through further analysis, the access delay analyst or end user can use the results in making informed decisions while weighing benefits against risks, ultimately resulting in greater system effectiveness with lower cost.

  7. Data Assimilation by delay-coordinate nudging

    Science.gov (United States)

    Pazo, Diego; Lopez, Juan Manuel; Carrassi, Alberto

    2016-04-01

    A new nudging method for data assimilation, delay-coordinate nudging, is presented. Delay-coordinate nudging makes explicit use of present and past observations in the formulation of the forcing driving the model evolution at each time-step. Numerical experiments with a low order chaotic system show that the new method systematically outperforms standard nudging in different model and observational scenarios, also when using an un-optimized formulation of the delay-nudging coefficients. A connection between the optimal delay and the dominant Lyapunov exponent of the dynamics is found based on heuristic arguments and is confirmed by the numerical results, providing a guideline for the practical implementation of the algorithm. Delay-coordinate nudging preserves the easiness of implementation, the intuitive functioning and the reduced computational cost of the standard nudging, making it a potential alternative especially in the field of seasonal-to-decadal predictions with large Earth system models that limit the use of more sophisticated data assimilation procedures.

  8. Time delay interferometry with moving spacecraft arrays

    International Nuclear Information System (INIS)

    Tinto, Massimo; Estabrook, F.B.; Armstrong, J.W.

    2004-01-01

    Space-borne interferometric gravitational wave detectors, sensitive in the low-frequency (millihertz) band, will fly in the next decade. In these detectors the spacecraft-to-spacecraft light-travel-times will necessarily be unequal, time varying, and (due to aberration) have different time delays on up and down links. The reduction of data from moving interferometric laser arrays in solar orbit will in fact encounter nonsymmetric up- and down-link light time differences that are about 100 times larger than has previously been recognized. The time-delay interferometry (TDI) technique uses knowledge of these delays to cancel the otherwise dominant laser phase noise and yields a variety of data combinations sensitive to gravitational waves. Under the assumption that the (different) up- and down-link time delays are constant, we derive the TDI expressions for those combinations that rely only on four interspacecraft phase measurements. We then turn to the general problem that encompasses time dependence of the light-travel times along the laser links. By introducing a set of noncommuting time-delay operators, we show that there exists a quite general procedure for deriving generalized TDI combinations that account for the effects of time dependence of the arms. By applying our approach we are able to re-derive the 'flex-free' expression for the unequal-arm Michelson combinations X 1 , and obtain the generalized expressions for the TDI combinations called relay, beacon, monitor, and symmetric Sagnac

  9. 75 FR 76746 - Agency Information Collection Activities: Declaration of Ultimate Consignee That Articles Were...

    Science.gov (United States)

    2010-12-09

    ... Activities: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or... That Articles Were Exported for Temporary Scientific or Educational Purposes. This is a proposed... forms of information. Title: Declaration of Ultimate Consignee That Articles Were Exported for Temporary...

  10. 7 CFR 4280.21 - Eligible REDG Ultimate Recipients and Projects.

    Science.gov (United States)

    2010-01-01

    ... care providers; (5) Projects that utilize Advanced Telecommunications or computer networks to... 7 Agriculture 15 2010-01-01 2010-01-01 false Eligible REDG Ultimate Recipients and Projects. 4280... Economic Development Loan and Grant Programs § 4280.21 Eligible REDG Ultimate Recipients and Projects. The...

  11. Influence of cracks and pitting corrosion on residual ultimate strength of stiffened plates

    Directory of Open Access Journals (Sweden)

    ZHANG Jing

    2018-02-01

    Full Text Available [Objectives] Ships and offshore platforms serve in the harsh sea environment for a long time. Cracks and pitting corrosion will occur in such a structure and the damage will affect its ultimate strength.[Methods] To investigate the influence of cracks and pitting corrosion on ultimate bearing capacity, the ultimate strength of a structure under axial compression is studied by using a nonlinear finite element. The mesh size of a stiffened plate with cracks and pitting corrosion is first discussed. Then the influence of the relative positions of cracks and pitting corrosion, number of corrosion points and crack length impact on the residual ultimate strength of damaged stiffened plates is discussed via a series of calculations.[Results] The results indicate that the increase in crack length and pitting corrosion significantly decreases the ultimate strength of a stiffened plate. [Conclusions] This provides a useful reference for designing and maintaining ships and offshore structures in their life cycles.

  12. Ultimate capacity and influenced factors analysis of nuclear RC containment subjected to internal pressure

    International Nuclear Information System (INIS)

    Song Chenning; Hou Gangling; Zhou Guoliang

    2014-01-01

    Ultimate compressive bearing capacity, influenced factors and its rules of nuclear RC containment are key problems of safety assessment, accident treatment and structure design, etc. Ultimate compressive bearing capacity of nuclear RC containment is shown by concrete damaged plasticity model and steel double liner model of ABAQUS. The study shows that the concrete of nuclear RC containment cylinder wall becomes plastic when the internal pressure is up to 0.87 MPa, the maximum tensile strain of steel liner exceeds 3000 × 10 6 and nuclear RC containment reaches ultimate status when the internal pressure is up to 1.02 MPa. The result shows that nuclear RC containment is in elastic condition under the design internal pressure and the bearing capacity meets requirement. Prestress and steel liner play key parts in the ultimate internal pressure and failure mode of nuclear RC containment. The study results have value for the analysis of ultimate compressive bearing capacity, structure design and safety assessment. (authors)

  13. Delayed breast implant reconstruction

    DEFF Research Database (Denmark)

    Hvilsom, Gitte B.; Hölmich, Lisbet R.; Steding-Jessen, Marianne

    2011-01-01

    the period 1999 to 2006; 239 one-stage procedures and 353 two-stage procedures. The postoperative course through November 2009 was evaluated by cumulative incidence adjusting for competing risks for the selected outcomes; hematoma, infection, seroma, implant rupture, severe capsular contracture (modified...

  14. Topological Acoustic Delay Line

    Science.gov (United States)

    Zhang, Zhiwang; Tian, Ye; Cheng, Ying; Wei, Qi; Liu, Xiaojun; Christensen, Johan

    2018-03-01

    Topological protected wave engineering in artificially structured media is at the frontier of ongoing metamaterials research that is inspired by quantum mechanics. Acoustic analogues of electronic topological insulators have recently led to a wealth of new opportunities in manipulating sound propagation with strikingly unconventional acoustic edge modes immune to backscattering. Earlier fabrications of topological insulators are characterized by an unreconfigurable geometry and a very narrow frequency response, which severely hinders the exploration and design of useful devices. Here we establish topologically protected sound in reconfigurable phononic crystals that can be switched on and off simply by rotating its three-legged "atoms" without altering the lattice structure. In particular, we engineer robust phase delay defects that take advantage of the ultrabroadband reflection-free sound propagation. Such topological delay lines serve as a paradigm in compact acoustic devices, interconnects, and electroacoustic integrated circuits.

  15. Delayed traumatic intracranial hematoma

    International Nuclear Information System (INIS)

    Tomita, Hiroki

    1984-01-01

    CT was performed serially within 24 hours after head injury in 64 patients having Glasgow Coma Scale of 14 or less or cranial fracture shown on roentgenogram. Delayed traumatic extradural hematoma was observed within 7-12 hours after head injury in 6 cases (9.4%). This was prominent in the frontal and occipital regions (67%). Good recovery was seen in 83.3%. Delayed traumatic intracerebral hematoma was observed within 6-24 hours after head injury in 17 cases (26.6%). This higher incidence was related to contre coup injury. Conservative treatment was possible in 14 of the 17 patients (82.4%), showing good recovery in 70%. (Namekawa, K.)

  16. Time-Delay Interferometry

    Directory of Open Access Journals (Sweden)

    Massimo Tinto

    2014-08-01

    Full Text Available Equal-arm detectors of gravitational radiation allow phase measurements many orders of magnitude below the intrinsic phase stability of the laser injecting light into their arms. This is because the noise in the laser light is common to both arms, experiencing exactly the same delay, and thus cancels when it is differenced at the photo detector. In this situation, much lower level secondary noises then set the overall performance. If, however, the two arms have different lengths (as will necessarily be the case with space-borne interferometers, the laser noise experiences different delays in the two arms and will hence not directly cancel at the detector. In order to solve this problem, a technique involving heterodyne interferometry with unequal arm lengths and independent phase-difference readouts has been proposed. It relies on properly time-shifting and linearly combining independent Doppler measurements, and for this reason it has been called time-delay interferometry (TDI. This article provides an overview of the theory, mathematical foundations, and experimental aspects associated with the implementation of TDI. Although emphasis on the application of TDI to the Laser Interferometer Space Antenna (LISA mission appears throughout this article, TDI can be incorporated into the design of any future space-based mission aiming to search for gravitational waves via interferometric measurements. We have purposely left out all theoretical aspects that data analysts will need to account for when analyzing the TDI data combinations.

  17. Summative Mass Analysis of Algal Biomass - Integration of Analytical Procedures: Laboratory Analytical Procedure (LAP)

    Energy Technology Data Exchange (ETDEWEB)

    Laurens, Lieve M. L.

    2016-01-13

    This procedure guides the integration of laboratory analytical procedures to measure algal biomass constituents in an unambiguous manner and ultimately achieve mass balance closure for algal biomass samples. Many of these methods build on years of research in algal biomass analysis.

  18. Seismic shear wall ISP NUPEC's seismic ultimate dynamic response test. Comparison report

    International Nuclear Information System (INIS)

    1996-01-01

    In the seismic design of a nuclear power plant, evaluation of the ultimate strength of the nuclear reactor building is an important subject for assessment of seismic reliability of the plant. In order to carry out the evaluation, the response characteristics of reinforced concrete seismic shear walls up to their ultimate state have to be understood. For this purpose, there is a need to develop reliable non-linear response analysis methods which enables the reliable ultimate strength evaluation of nuclear reactor buildings. Along with this need, many computer codes have been developed. These computer codes are compared. (K.A.)

  19. Distributed Optimal Consensus Control for Multiagent Systems With Input Delay.

    Science.gov (United States)

    Zhang, Huaipin; Yue, Dong; Zhao, Wei; Hu, Songlin; Dou, Chunxia; Huaipin Zhang; Dong Yue; Wei Zhao; Songlin Hu; Chunxia Dou; Hu, Songlin; Zhang, Huaipin; Dou, Chunxia; Yue, Dong; Zhao, Wei

    2018-06-01

    This paper addresses the problem of distributed optimal consensus control for a continuous-time heterogeneous linear multiagent system subject to time varying input delays. First, by discretization and model transformation, the continuous-time input-delayed system is converted into a discrete-time delay-free system. Two delicate performance index functions are defined for these two systems. It is shown that the performance index functions are equivalent and the optimal consensus control problem of the input-delayed system can be cast into that of the delay-free system. Second, by virtue of the Hamilton-Jacobi-Bellman (HJB) equations, an optimal control policy for each agent is designed based on the delay-free system and a novel value iteration algorithm is proposed to learn the solutions to the HJB equations online. The proposed adaptive dynamic programming algorithm is implemented on the basis of a critic-action neural network (NN) structure. Third, it is proved that local consensus errors of the two systems and weight estimation errors of the critic-action NNs are uniformly ultimately bounded while the approximated control policies converge to their target values. Finally, two simulation examples are presented to illustrate the effectiveness of the developed method.

  20. Ultimate Bound of a 3D Chaotic System and Its Application in Chaos Synchronization

    Directory of Open Access Journals (Sweden)

    Jiezhi Wang

    2014-01-01

    Full Text Available Two ellipsoidal ultimate boundary regions of a special three-dimensional (3D chaotic system are proposed. To this chaotic system, the linear coefficient of the ith state variable in the ith state equation has the same sign; it also has two one-order terms and one quadratic cross-product term in each equation. A numerical solution and an analytical expression of the ultimate bounds are received. To get the analytical expression of the ultimate boundary region, a new result of one maximum optimization question is proved. The corresponding ultimate boundary regions are demonstrated through numerical simulations. Utilizing the bounds obtained, a linear controller is proposed to achieve the complete chaos synchronization. Numerical simulation exhibits the feasibility of the designed scheme.

  1. LRFD software for design and actual ultimate capacity of confined rectangular columns.

    Science.gov (United States)

    2013-04-01

    The analysis of concrete columns using unconfined concrete models is a well established practice. On the : other hand, prediction of the actual ultimate capacity of confined concrete columns requires specialized nonlinear : analysis. Modern codes and...

  2. [Deniss Hanovs, Valdis Tēraudkalns: Ultimate Freedom - no choice] / Olaf Mertelsmann

    Index Scriptorium Estoniae

    Mertelsmann, Olaf, 1969-

    2014-01-01

    Arvustus: Deniss Hanovs, Valdis Tēraudkalns: Ultimate Freedom - no choice. The culture of authoritarianism in Latvia, 1934-1940. (Central and Eastern Europe. Reginal perspectives in global context, Bd. 2.) Brill. Leiden-Boston 2013

  3. Reduced design load basis for ultimate blade loads estimation in multidisciplinary design optimization frameworks

    DEFF Research Database (Denmark)

    Pavese, Christian; Tibaldi, Carlo; Larsen, Torben J.

    2016-01-01

    The aim is to provide a fast and reliable approach to estimate ultimate blade loads for a multidisciplinary design optimization (MDO) framework. For blade design purposes, the standards require a large amount of computationally expensive simulations, which cannot be efficiently run each cost...... function evaluation of an MDO process. This work describes a method that allows integrating the calculation of the blade load envelopes inside an MDO loop. Ultimate blade load envelopes are calculated for a baseline design and a design obtained after an iteration of an MDO. These envelopes are computed...... for a full standard design load basis (DLB) and a deterministic reduced DLB. Ultimate loads extracted from the two DLBs with the two blade designs each are compared and analyzed. Although the reduced DLB supplies ultimate loads of different magnitude, the shape of the estimated envelopes are similar...

  4. Delayed child-bearing.

    Science.gov (United States)

    Johnson, Jo-Ann; Tough, Suzanne

    2012-01-01

    To provide an overview of delayed child-bearing and to describe the implications for women and health care providers. Delayed child-bearing, which has increased greatly in recent decades, is associated with an increased risk of infertility, pregnancy complications, and adverse pregnancy outcome. This guideline provides information that will optimize the counselling and care of Canadian women with respect to their reproductive choices. Maternal age is the most important determinant of fertility, and obstetric and perinatal risks increase with maternal age. Many women are unaware of the success rates or limitations of assisted reproductive technology and of the increased medical risks of delayed child-bearing, including multiple births, preterm delivery, stillbirth, and Caesarean section. This guideline provides a framework to address these issues. Studies published between 2000 and August 2010 were retrieved through searches of PubMed and the Cochrane Library using appropriate key words (delayed child-bearing, deferred pregnancy, maternal age, assisted reproductive technology, infertility, and multiple births) and MeSH terms (maternal age, reproductive behaviour, fertility). The Internet was also searched using similar key words, and national and international medical specialty societies were searched for clinical practice guidelines and position statements. Data were extracted based on the aims, sample, authors, year, and results. The quality of evidence was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). The Society of Obstetricians and Gynaecologists of Canada. RECOMMENDATIONS 1. Women who delay child-bearing are at increased risk of infertility. Prospective parents, especially women, should know that their fecundity and fertility begin to decline significantly after 32 years of age. Prospective parents should know that assisted reproductive technologies cannot guarantee a live birth or completely

  5. The Aviation System Analysis Capability Airport Capacity and Delay Models

    Science.gov (United States)

    Lee, David A.; Nelson, Caroline; Shapiro, Gerald

    1998-01-01

    The ASAC Airport Capacity Model and the ASAC Airport Delay Model support analyses of technologies addressing airport capacity. NASA's Aviation System Analysis Capability (ASAC) Airport Capacity Model estimates the capacity of an airport as a function of weather, Federal Aviation Administration (FAA) procedures, traffic characteristics, and the level of technology available. Airport capacity is presented as a Pareto frontier of arrivals per hour versus departures per hour. The ASAC Airport Delay Model allows the user to estimate the minutes of arrival delay for an airport, given its (weather dependent) capacity. Historical weather observations and demand patterns are provided by ASAC as inputs to the delay model. The ASAC economic models can translate a reduction in delay minutes into benefit dollars.

  6. Recommendation for basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes

    International Nuclear Information System (INIS)

    2006-12-01

    In 2003 the Danish Parliament consented to let the government start the preparation of a basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes. The present report is the result of the preparation process, and it describes the fundamental safety and environmental principles for establishing an ultimate storage, including determining the principles for the site selection, storage construction, and safety analyses. (LN)

  7. A Technique for Temperature and Ultimate Load Calculations of Thin Targets in a Pulsed Electron Beam

    DEFF Research Database (Denmark)

    Hansen, Jørgen-Walther; Lundsager, Per

    1979-01-01

    A technique is presented for the calculation of transient temperature distributions and ultimate load of rotationally symmetric thin membranes with uniform lateral load and exposed to a pulsed electron beam from a linear accelerator. Heat transfer by conduction is considered the only transfer...... mechanism. The ultimate load is calculated on the basis of large plastic strain analysis. Analysis of one aluminum and one titanium membrane is shown....

  8. Ultimate storage of spent fuel elements from the AVR experimental nuclear power plant in the Asse Salt Mine

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, J.

    1975-02-15

    The present paper is intended to serve as the basis for the licensing procedures both in respect of the transport and storage techniques and also for the ultimate storage itself. In regard to the technique it will be shown on the basis of design drawings and calculations that the handling, transport and storage of the fuel elements can be safely carried out in accordance with the regulations in force. In regard to the ultimate storage itself, since no highly radioactive wastes with a long-lived actinide content have yet been stored, it will be necessary to show that an unacceptable contamination of the biosphere will be avoided even in the long term under all anticipated conditions. It will further be necessary to show by calculations and suitable tests, in view of the radioactive gas and fissile material content, that no danger due to gas release from the fuel elements will arise during the operating life of the mine and that a nuclear criticality risk can be excluded for all time.

  9. Delaying information search

    Directory of Open Access Journals (Sweden)

    Yaniv Shani

    2012-11-01

    Full Text Available In three studies, we examined factors that may temporarily attenuate information search. People are generally curious and dislike uncertainty, which typically encourages them to look for relevant information. Despite these strong forces that promote information search, people sometimes deliberately delay obtaining valuable information. We find they may do so when they are concerned that the information might interfere with future pleasurable activities. Interestingly, the decision to search or to postpone searching for information is influenced not only by the value and importance of the information itself but also by well-being maintenance goals related to possible detrimental effects that negative knowledge may have on unrelated future plans.

  10. Educational attainment and ultimate fertility among Swedish women born in 1955-59

    Directory of Open Access Journals (Sweden)

    Gerda Neyer

    2006-05-01

    Full Text Available This is the second of two companion papers addressing the association between educational attainment and fertility for some sixty educational groups of Swedish women, defined according to field of education as well as level of education. The first paper is about childlessness and education, the present one about the mean number of children ever born. We find that ultimate fertility decreases somewhat with an increasing educational level, but its dependence on the field of education is much more impressive. In general, educational groups with relatively little childlessness also have relatively high ultimate fertility, and educational groups with much childlessness have relatively low ultimate fertility. In particular, women educated for the teaching or health-care professions have less childlessness and a higher ultimate fertility than others. Conversely, women with an education for esthetic or (non-teacher humanist occupations have unusually high fractions childless and low ultimate fertility. Women with religious educations stand out by having very high fractions childless but quite ordinary mean ultimate fertility nevertheless; such women have very little childbearing outside of marriage. Women with research degrees have remarkably ordinary childbearing behavior; they do not forego motherhood to the extent that some theories would predict.

  11. Excess glycogen does not resolve high ultimate pH of oxidative muscle.

    Science.gov (United States)

    England, Eric M; Matarneh, Sulaiman K; Oliver, Emily M; Apaoblaza, Ariel; Scheffler, Tracy L; Shi, Hao; Gerrard, David E

    2016-04-01

    Skeletal muscle glycogen content can impact the extent of postmortem pH decline. Compared to glycolytic muscles, oxidative muscles contain lower glycogen levels antemortem which may contribute to the higher ultimate pH. In an effort to explore further the participation of glycogen in postmortem metabolism, we postulated that increasing the availability of glycogen would drive additional pH decline in oxidative muscles to equivalent pH values similar to the ultimate pH of glycolytic muscles. Glycolysis and pH declines were compared in porcine longissimus lumborum (glycolytic) and masseter (oxidative) muscles using an in vitro system in the presence of excess glycogen. The ultimate pH of the system containing longissimus lumborum reached a value similar to that observed in intact muscle. The pH decline of the system containing masseter samples stopped prematurely resulting in a higher ultimate pH which was similar to that of intact masseter muscle. To investigate further, we titrated powdered longissimus lumborum and masseter samples in the reaction buffer. As the percentage of glycolytic sample increased, the ultimate pH decreased. These data show that oxidative muscle produces meat with a high ultimate pH regardless of glycogen content and suggest that inherent muscle factors associated with glycolytic muscle control the extent of pH decline in pig muscles. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Assessment on Ultimate Load of Cold-formed Steel Channel (CFSC Stub Column

    Directory of Open Access Journals (Sweden)

    Mohd Sani Mohd Syahrul Hisyam

    2015-01-01

    Full Text Available Cold-formed steel is used as the non-structural and structural material in civil engineering work and building. Cold-formed steel channel is selected and cut into 100 mm, 200 mm, 300 mm, 400 mm and 500 mm. The slenderness ratio is calculated and noted as a stub or short column because below 40. The column is tested by using Universal Testing Machine to determine the ultimate load of the stub column. Besides, the CFSC is determined the material properties of CFSC for checking it’s the originality of steel based material. The experimental data are tested and compared with the Direct Strength Method (DSM. It showed that the CFSC1 with a height of 100 mm is reported to have a higher value of ultimate load when compared with other samples. When the height of the stub column increased, the ultimate load of the sample is decreased. Then, the CFSC1 also showed a higher in initial stiffness when compared with other samples. All samples are shown having a higher data in ultimate load when compared with the Direct Strength Method prediction. The ultimate load of experimental and DSM all gave a ratio below 1.03. Finally, all samples can further recommend determining the relation between the ultimate loads with variations of height of the column.

  13. Vehicle barrier with access delay

    Science.gov (United States)

    Swahlan, David J; Wilke, Jason

    2013-09-03

    An access delay vehicle barrier for stopping unauthorized entry into secure areas by a vehicle ramming attack includes access delay features for preventing and/or delaying an adversary from defeating or compromising the barrier. A horizontally deployed barrier member can include an exterior steel casing, an interior steel reinforcing member and access delay members disposed within the casing and between the casing and the interior reinforcing member. Access delay members can include wooden structural lumber, concrete and/or polymeric members that in combination with the exterior casing and interior reinforcing member act cooperatively to impair an adversarial attach by thermal, mechanical and/or explosive tools.

  14. Platelet-rich plasma, the ultimate secret for youthful skin elixir and hair growth triggering.

    Science.gov (United States)

    Elghblawi, Ebtisam

    2017-09-08

    The clinical application of platelet-rich plasma (PRP) is based on the increase in the concentration of growth factors that are released from alpha-granule of the concentrated platelets and in the secretion of proteins which are able to capitalize on the healing process at the cellular level. It has been invented to restore the natural beauty by starting the natural rejuvenation process of the skin and aiming to make it function as a younger one and to keep the skin youthful and maintain it. Besides that, it is also emerged to include hairs as a new injectable procedure to enable stimulating hair growth locally and topically; preventing its fall; improving hair shaft, hair stem, and its caliber; increasing its shine, vitality, and pliability; and declining hair splitting and breakage. Thus, youth is in your blood as it has a magical power imposed in the platelet factors. There is, however, no standardization of the techniques besides insufficient description of the adopted procedures. Not long, autologous platelet-rich plasma (PRP) has surfaced strongly in diverse medical specialties including plastic, wound healing and diabetic ulcers, orthopedic, trauma, ocular surgery, dry eye for eyelid injection, urology for urinary incontinence, sexual wellness, cutaneous surgery, sport medicine, dentistry and dermatology, and aesthetic applications. PRP proved to promote wound healing and aid in facelift, volumetric skin, skin rejuvenation, regeneration, and reconstruction; improve wrinkling; stimulate hair growth; increase hair follicle viability and its survival rate; prevent apoptosis; increase and prolong the anagen hair growth stage; and delay the progression to catagen hair cycle stage with increased density in hair loss and hair transplantation. The aims of this extensive review were to cover all PRP application aspects that are carried out in aesthetic dermatology and to assess the literature on platelet-rich plasma outcomes on main aesthetic practices of general

  15. The establishment and analysis of TRACE model for ultimate response guideline of Chinshan nuclear power plant - 15448

    International Nuclear Information System (INIS)

    Huang, J.J.; Wang, J.R.; Shih, C.; Chen, S.W.; Liao, L.Y.; Lin, H.T.

    2015-01-01

    The purpose of this research is to use TRACE code to perform a simulation that executes the procedures of URG (Ultimate Response Guidelines) to deal with Fukushima-like accidents. TRACE is an advanced thermal hydraulic code that has been developed by the United States Nuclear Regulatory Commission for NPP safety analysis. In this work TRACE has been used to analyze the thermal hydraulic model for the URG of the Chinshan nuclear power plant that is composed of 2 BWR-type reactors. URG includes 2-stage depressurization, alternative water injection and removing decay heat through the ejection from containment. The 2-stage depressurization strategy includes controlled depressurization and emergency depressurization to replace traditional one-stage depressurization. Results show that by comparing with one-stage depressurization strategy, 2-stage depressurization strategy is able to reduce peak cladding temperature (PCT) effectively and needs much less minimum flow rate of alternative water injection in the accident

  16. Delayed rule following.

    Science.gov (United States)

    Schmitt, D R

    2001-01-01

    Although the elements of a fully stated rule (discriminative stimulus [S(D)], some behavior, and a consequence) can occur nearly contemporaneously with the statement of the rule, there is often a delay between the rule statement and the S(D). The effects of this delay on rule following have not been studied in behavior analysis, but they have been investigated in rule-like settings in the areas of prospective memory (remembering to do something in the future) and goal pursuit. Discriminative events for some behavior can be event based (a specific setting stimulus) or time based. The latter are more demanding with respect to intention following and show age-related deficits. Studies suggest that the specificity with which the components of a rule (termed intention) are stated has a substantial effect on intention following, with more detailed specifications increasing following. Reminders of an intention, too, are most effective when they refer specifically to both the behavior and its occasion. Covert review and written notes are two effective strategies for remembering everyday intentions, but people who use notes appear not to be able to switch quickly to covert review. By focusing on aspects of the setting and rule structure, research on prospective memory and goal pursuit expands the agenda for a more complete explanation of rule effects.

  17. Stability and delay sensitivity of neutral fractional-delay systems.

    Science.gov (United States)

    Xu, Qi; Shi, Min; Wang, Zaihua

    2016-08-01

    This paper generalizes the stability test method via integral estimation for integer-order neutral time-delay systems to neutral fractional-delay systems. The key step in stability test is the calculation of the number of unstable characteristic roots that is described by a definite integral over an interval from zero to a sufficient large upper limit. Algorithms for correctly estimating the upper limits of the integral are given in two concise ways, parameter dependent or independent. A special feature of the proposed method is that it judges the stability of fractional-delay systems simply by using rough integral estimation. Meanwhile, the paper shows that for some neutral fractional-delay systems, the stability is extremely sensitive to the change of time delays. Examples are given for demonstrating the proposed method as well as the delay sensitivity.

  18. Characteristics of hypertrophic cardiomyopathy on delayed contrast-enhanced MRI

    International Nuclear Information System (INIS)

    Yan Chaowu; Zhao Shihua; Li Hua; Jiang Shiliang; Lu Minjie; Zhang Yan; Wei Yunqing; Ling Jian; Fang Wei

    2010-01-01

    Objective: To analyze the characteristics of hypertrophic cardiomyopathy (HCM) on delayed contrast-enhanced cardiac magnetic resonance imaging (CMRI). Methods: All patients underwent delayed contrast-enhanced CMRI. The left ventricle was divided into 9 segments to assess the location, extent and function of the hypertrophic segments. The t test was applied for the statistics. Results: Of 154 patients, delayed enhancement of' hypertrophic segment was found in 95 cases and non-delayed enhancement in 59 cases. The thickness and number of hypertrophic segment in patients with delayed enhancement were larger than those with non-delayed enhancement [(24.8±5.5) mm vs (20.4± 3.8) mm, t=3.82, P<0.05; (3.3±1.9) vs (2.4±1.7), t=2.26, P<0.05], and the age was younger [(46.0±15.2) years vs (55.0±11.9) years, t=-3.67, P<0.05]. The diffuse enhancement was found in 62 patients, and confluent enhancement in 33 patients. Confluent enhancement was found in all 14 patients after the alcohol ablation procedure. Conclusion: The age, thickness and number of hypertrophic segments in patients with delayed enhancement are different from those with non-delayed enhancement. (authors)

  19. Delay tolerant networks

    CERN Document Server

    Gao, Longxiang; Luan, Tom H

    2015-01-01

    This brief presents emerging and promising communication methods for network reliability via delay tolerant networks (DTNs). Different from traditional networks, DTNs possess unique features, such as long latency and unstable network topology. As a result, DTNs can be widely applied to critical applications, such as space communications, disaster rescue, and battlefield communications. The brief provides a complete investigation of DTNs and their current applications, from an overview to the latest development in the area. The core issue of data forward in DTNs is tackled, including the importance of social characteristics, which is an essential feature if the mobile devices are used for human communication. Security and privacy issues in DTNs are discussed, and future work is also discussed.

  20. Dynamical Behaviors of Stochastic Reaction-Diffusion Cohen-Grossberg Neural Networks with Delays

    Directory of Open Access Journals (Sweden)

    Li Wan

    2012-01-01

    Full Text Available This paper investigates dynamical behaviors of stochastic Cohen-Grossberg neural network with delays and reaction diffusion. By employing Lyapunov method, Poincaré inequality and matrix technique, some sufficient criteria on ultimate boundedness, weak attractor, and asymptotic stability are obtained. Finally, a numerical example is given to illustrate the correctness and effectiveness of our theoretical results.

  1. Stochastic Delay Population Dynamics under Regime Switching: Global Solutions and Extinction

    Directory of Open Access Journals (Sweden)

    Zheng Wu

    2013-01-01

    Full Text Available This paper is concerned with a delay Lotka-Volterra model under regime switching diffusion in random environment. By using generalized Itô formula, Gronwall inequality and Young’s inequality, some sufficient conditions for existence of global positive solutions and stochastically ultimate boundedness are obtained, respectively. Finally, an example is given to illustrate the main results.

  2. Ultimate dynamics of the Kirschner-Panetta model: Tumor eradication and related problems

    Science.gov (United States)

    Starkov, Konstantin E.; Krishchenko, Alexander P.

    2017-10-01

    In this paper we consider the ultimate dynamics of the Kirschner-Panetta model which was created for studying the immune response to tumors under special types of immunotherapy. New ultimate upper bounds for compact invariant sets of this model are given, as well as sufficient conditions for the existence of a positively invariant polytope. We establish three types of conditions for the nonexistence of compact invariant sets in the domain of the tumor-cell population. Our main results are two types of conditions for global tumor elimination depending on the ratio between the proliferation rate of the immune cells and their mortality rate. These conditions are described in terms of simple algebraic inequalities imposed on model parameters and treatment parameters. Our theoretical studies of ultimate dynamics are complemented by numerical simulation results.

  3. Revisiting perceptions of quality of hospice care: managing for the ultimate referral.

    Science.gov (United States)

    Churchman, Richard; York, Grady S; Woodard, Beth; Wainright, Charles; Rau-Foster, Mary

    2014-08-01

    Hospice services provided in the final months of life are delivered through complex interpersonal relationships between caregivers, patients, and families. Often, service value and quality are defined by these interpersonal interactions. This understanding provides hospice leaders with an enormous opportunity to create processes that provide the optimal level of care during the last months of life. The authors argue that the ultimate referral is attained when a family member observes the care of a loved one, and the family member conveys a desire to receive the same quality of services their loved one received at that facility. The point of this article is to provide evidence that supports the methods to ultimately enhance the patient's and family's experience and increase the potential for the ultimate referral. © The Author(s) 2013.

  4. Ultimate Owner and Firm Performance - Evidence from Romanian Mining and Quarrying Listed Firms

    Directory of Open Access Journals (Sweden)

    Cosmin MIHAI

    2012-08-01

    Full Text Available The main objectives of this paper are to describe the necessary steps to identify the ultimate owner and to investigate the relation between the ultimate ownership and the financial performance of Romanian mining and quarrying listed firms. The study was conducted for the companies listed on Bucharest Stock Exchange, in both regulated and non-regulated segments. The final sample included 17 companies of mining and quarrying. Return on Equity was used for measuring the financial performance of the firms. The ultimate ownership was measured by the percentage of voting rights held by a shareholder. Econometric tools like multiple linear regression analysis were used for analysis. The results of the study suggest that there is a significant negative link between financial performance and divergence between voting rights and cash-flow rights.

  5. Location Estimation using Delayed Measurements

    DEFF Research Database (Denmark)

    Bak, Martin; Larsen, Thomas Dall; Nørgård, Peter Magnus

    1998-01-01

    When combining data from various sensors it is vital to acknowledge possible measurement delays. Furthermore, the sensor fusion algorithm, often a Kalman filter, should be modified in order to handle the delay. The paper examines different possibilities for handling delays and applies a new techn...... technique to a sensor fusion system for estimating the location of an autonomous guided vehicle. The system fuses encoder and vision measurements in an extended Kalman filter. Results from experiments in a real environment are reported...

  6. Modeling delay in genetic networks: from delay birth-death processes to delay stochastic differential equations.

    Science.gov (United States)

    Gupta, Chinmaya; López, José Manuel; Azencott, Robert; Bennett, Matthew R; Josić, Krešimir; Ott, William

    2014-05-28

    Delay is an important and ubiquitous aspect of many biochemical processes. For example, delay plays a central role in the dynamics of genetic regulatory networks as it stems from the sequential assembly of first mRNA and then protein. Genetic regulatory networks are therefore frequently modeled as stochastic birth-death processes with delay. Here, we examine the relationship between delay birth-death processes and their appropriate approximating delay chemical Langevin equations. We prove a quantitative bound on the error between the pathwise realizations of these two processes. Our results hold for both fixed delay and distributed delay. Simulations demonstrate that the delay chemical Langevin approximation is accurate even at moderate system sizes. It captures dynamical features such as the oscillatory behavior in negative feedback circuits, cross-correlations between nodes in a network, and spatial and temporal information in two commonly studied motifs of metastability in biochemical systems. Overall, these results provide a foundation for using delay stochastic differential equations to approximate the dynamics of birth-death processes with delay.

  7. Modeling delay in genetic networks: From delay birth-death processes to delay stochastic differential equations

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Chinmaya; López, José Manuel; Azencott, Robert; Ott, William [Department of Mathematics, University of Houston, Houston, Texas 77004 (United States); Bennett, Matthew R. [Department of Biochemistry and Cell Biology, Rice University, Houston, Texas 77204, USA and Institute of Biosciences and Bioengineering, Rice University, Houston, Texas 77005 (United States); Josić, Krešimir [Department of Mathematics, University of Houston, Houston, Texas 77004 (United States); Department of Biology and Biochemistry, University of Houston, Houston, Texas 77204 (United States)

    2014-05-28

    Delay is an important and ubiquitous aspect of many biochemical processes. For example, delay plays a central role in the dynamics of genetic regulatory networks as it stems from the sequential assembly of first mRNA and then protein. Genetic regulatory networks are therefore frequently modeled as stochastic birth-death processes with delay. Here, we examine the relationship between delay birth-death processes and their appropriate approximating delay chemical Langevin equations. We prove a quantitative bound on the error between the pathwise realizations of these two processes. Our results hold for both fixed delay and distributed delay. Simulations demonstrate that the delay chemical Langevin approximation is accurate even at moderate system sizes. It captures dynamical features such as the oscillatory behavior in negative feedback circuits, cross-correlations between nodes in a network, and spatial and temporal information in two commonly studied motifs of metastability in biochemical systems. Overall, these results provide a foundation for using delay stochastic differential equations to approximate the dynamics of birth-death processes with delay.

  8. Modeling delay in genetic networks: From delay birth-death processes to delay stochastic differential equations

    International Nuclear Information System (INIS)

    Gupta, Chinmaya; López, José Manuel; Azencott, Robert; Ott, William; Bennett, Matthew R.; Josić, Krešimir

    2014-01-01

    Delay is an important and ubiquitous aspect of many biochemical processes. For example, delay plays a central role in the dynamics of genetic regulatory networks as it stems from the sequential assembly of first mRNA and then protein. Genetic regulatory networks are therefore frequently modeled as stochastic birth-death processes with delay. Here, we examine the relationship between delay birth-death processes and their appropriate approximating delay chemical Langevin equations. We prove a quantitative bound on the error between the pathwise realizations of these two processes. Our results hold for both fixed delay and distributed delay. Simulations demonstrate that the delay chemical Langevin approximation is accurate even at moderate system sizes. It captures dynamical features such as the oscillatory behavior in negative feedback circuits, cross-correlations between nodes in a network, and spatial and temporal information in two commonly studied motifs of metastability in biochemical systems. Overall, these results provide a foundation for using delay stochastic differential equations to approximate the dynamics of birth-death processes with delay

  9. On the decrease of ultimate elongation of gum elastomer by irradiation

    International Nuclear Information System (INIS)

    Ito, Masayuki

    1986-01-01

    The reason why the ultimate elongation of gum elastomer decreases by irradiation was studied. The sample used is tetrafluoroethylenepropylene copolymer vulcanized which is a heat resistant elastomer. The sample was irradiated by a electron beam at room temperature. Cross-linking predominate in the operation. (Case 1) Scission predominant condition (Case 2) was given by irradiation of Co-60 γ ray at 100 deg C. Alternative irradiation of γ ray and electron beam under above condition can keep the original cross-linking density by the appropriate choice of each of the doses. (Case 3) The three cases mentioned above involve all of the cases of radiation induced aging of elastomers. Therefor, the following explanation for three cases shows the reason why the ultimate elongation of gum elastomer decreases by irradiation. Case 1. Cross-linking predominant condition. Ultimate elongation is proportional to -0.5 power of the dose. This fact can be explicable by the model of Buche, i.e. the breaking of a short chain causes another to break and that so on throughout the whole sample. Case 2. Chain scission predominant condition. Ultimate elongation increases by irradiation for a certain dose. This fact can understand by the model of Buche. But from a certain dose ultimate elongation does not increase. In the period the structure of the sample turned to be the same structure as the low molecular weight amorphose polymer vulcanized. Case 3. Rate of cross-linking and scission is the same. The average chain length does not chainge in the condition. But the distribution of chain length became wider and wider by irradiation. The increase of short chain result the decrease in ultimate elongation. (author)

  10. Systematic of delayed neutron parameters

    International Nuclear Information System (INIS)

    Isaev, S.G.; Piksaikin, V.M.

    2000-01-01

    The experimental studies of the energy dependence of the delayed neutron (DN) parameters for various fission systems has shown that the behaviour of a some combination of delayed neutron parameters has a similar features. On the basis of this findings the systematics of delayed neutron experimental data for thorium, uranium, plutonium and americium isotopes have been investigated with the purpose to find a correlation of DN parameters with characteristics of fissioning system as well as a correlation between the delayed neutron parameters themselves. It was presented the preliminary results which were obtained during study the physics interpretation of the results [ru

  11. Time Delay of CGM Sensors

    Science.gov (United States)

    Schmelzeisen-Redeker, Günther; Schoemaker, Michael; Kirchsteiger, Harald; Freckmann, Guido; Heinemann, Lutz; del Re, Luigi

    2015-01-01

    Background: Continuous glucose monitoring (CGM) is a powerful tool to support the optimization of glucose control of patients with diabetes. However, CGM systems measure glucose in interstitial fluid but not in blood. Rapid changes in one compartment are not accompanied by similar changes in the other, but follow with some delay. Such time delays hamper detection of, for example, hypoglycemic events. Our aim is to discuss the causes and extent of time delays and approaches to compensate for these. Methods: CGM data were obtained in a clinical study with 37 patients with a prototype glucose sensor. The study was divided into 5 phases over 2 years. In all, 8 patients participated in 2 phases separated by 8 months. A total number of 108 CGM data sets including raw signals were used for data analysis and were processed by statistical methods to obtain estimates of the time delay. Results: Overall mean (SD) time delay of the raw signals with respect to blood glucose was 9.5 (3.7) min, median was 9 min (interquartile range 4 min). Analysis of time delays observed in the same patients separated by 8 months suggests a patient dependent delay. No significant correlation was observed between delay and anamnestic or anthropometric data. The use of a prediction algorithm reduced the delay by 4 minutes on average. Conclusions: Prediction algorithms should be used to provide real-time CGM readings more consistent with simultaneous measurements by SMBG. Patient specificity may play an important role in improving prediction quality. PMID:26243773

  12. Environmental procedures

    International Nuclear Information System (INIS)

    1992-01-01

    The European Bank has pledged in its Agreement to place environmental management at the forefront of its operations to promote sustainable economic development in central and eastern Europe. The Bank's environmental policy is set out in the document titled, Environmental Management: The Bank's Policy Approach. This document, Environmental Procedures, presents the procedures which the European Bank has adopted to implement this policy approach with respect to its operations. The environmental procedures aim to: ensure that throughout the project approval process, those in positions of responsibility for approving projects are aware of the environmental implications of the project, and can take these into account when making decisions; avoid potential liabilities that could undermine the success of a project for its sponsors and the Bank; ensure that environmental costs are estimated along with other costs and liabilities; and identify opportunities for environmental enhancement associated with projects. The review of environmental aspects of projects is conducted by many Bank staff members throughout the project's life. This document defines the responsibilities of the people and groups involved in implementing the environmental procedures. Annexes contain Environmental Management: The Bank's Policy Approach, examples of environmental documentation for the project file and other ancillary information

  13. Ultimate strength and ductility of steel reinforced concrete beam-columns

    International Nuclear Information System (INIS)

    Shohara, Ryoichi

    1991-01-01

    The ultimate strength and ductility of SRC beam-columns are investigated using the data gathered in Architectural Institute of Japan. Though the simple superposed strength formula in AIJ standard underestimates the strength of SRC beam-column failed in flexure, the generalized superposed strength formula estimates it satisfactory. The strength formula in AIJ standard does not good agreement with test data. The SRC beam-column failed in shear has almost equalductility with that failed in flexure owing to the encased steel. Author presents the formulas which estimate the ultimate deformation angle for SRC beam-columns. (author)

  14. Behaviour of concrete nuclear containment structures upto ultimate failure with special reference to MAPP-1 containment

    International Nuclear Information System (INIS)

    Appa Rao, T.V.S.R.

    1975-01-01

    Theoretical and experimental methods for investigating the behaviour of concrete secondary containment structures subjected to loads upto their ultimate failure have been discussed in the paper. Need for inelastic nonlinear analysis of containments has been emphasized. Different contitutive models of concrete that can be employed in the nonlinear analysis of concrete structures were briefly reviewed. Based on the experimental results obtained in a 1:12 scale model test conducted at the Structural Engineering Research (Regional) Centre, Madras, behaviour of the MAPP-1 containment to internal pressure loading upto its ultimate failure has been discussed. (author)

  15. Decision basis for a Danish ultimate storage for low and intermediate radioactive wastes

    International Nuclear Information System (INIS)

    2008-11-01

    In 2003 the Danish Parliament consented to let the government start the preparation of a basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes. The present report was prepared by a working group and it presents the final proposal for such a decision basis. The report describes the fundamental safety and environmental principles for establishing an ultimate storage, including determining the principles for site selection, storage construction, and safety analysis. In an appendix, the amount, types, and activity level of the Danish radioactive wastes are presented. (ln)

  16. Conception of electron beam-driven subcritical molten salt ultimate safety reactor

    Energy Technology Data Exchange (ETDEWEB)

    Abalin, S.S.; Alekseev, P.N.; Ignat`ev, V.V. [Kurchatov Institute, Moscow (Russian Federation)] [and others

    1995-10-01

    This paper is a preliminary sketch of a conception to develop the {open_quotes}ultimate safety reactor{close_quotes} using modern reactor and accelerator technologies. This approach would not require a long-range R&D program. The ultimate safety reactor could produce heat and electric energy, expand the production of fuel, or be used for the transmutation of long-lived wastes. The use of the combined double molten salt reactor system allows adequate neutron multiplication to permit using an electron accelerator for the initial neutron flux. The general parameters of such a system are discussed in this paper.

  17. New approach to design and performance assessment of delay lines for radioactive rare gases

    International Nuclear Information System (INIS)

    Wilhelmova, L.; Dvorak, Z.; Cejnar, F.

    1981-01-01

    The evaluation and analysis are discussed of the dynamic adsorption of rare gases in the delay lines of nuclear power plants. The method of statistical momenta was used for deriving relations for the calculation of penetration curves of radioactive isotopes of rare gases through a delay line. Relations were also derived for the calculation of the capacity of delay line adsorption beds for both continuous and discontinuous operation. The procedures for the design and the derivation of the function of delay lines take into account the actual conditions of delay line operation in nuclear power plants. (author)

  18. Isolating the delay component of impulsive choice in adolescent rats

    Directory of Open Access Journals (Sweden)

    Jesse eMcClure

    2014-01-01

    Full Text Available Impulsive choice — the preference for small immediate rewards over larger delayed rewards — has been linked to various psychological conditions ranging from behavioral disorders to addiction. These links highlight the critical need to dissect the various components of this multifaceted behavioral trait. Delay discounting tasks allow researchers to study an important factor of this behavior: how the subjective value of a rewards changes over a delay period. However, existing methods of delay discounting include a confound of modifying reward sizes during the procedure. Here we present a new approach of using a single constant reward size to assess delay discounting. A complementary approach could hold delay constant and assess the utility of changing quantities of a reward. Isolating these behavioral components can advance our ability to explore the behavioral complexity of impulsive choice. We present the methods for isolating delay in detail, and further capitalize on this method by pairing it with a standard peak interval task to test whether individual variation in delay discounting can be explained by differences in perception of time in male and female adolescent rats. We find that rats that were more precise in discriminating time intervals were also less impulsive in their choice. Our data suggest that differences in timing and delay discounting are not causally related, but instead are more likely influenced by a common factor. Further, the mean-level change in our measure between postnatal day 28 and 42 suggests this test may be capturing a developmental change in this factor. In summary, this new method of isolating individual components of impulsive choice (delay or quantity can be efficiently applied in either adolescent or adult animal models and may help elucidate the mechanisms underlying impulsivity and its links to psychological disorders.

  19. Radiochemical procedures

    International Nuclear Information System (INIS)

    Lyon, W.S.

    1982-01-01

    The modern counting instrumentation has largely obviated the need for separation processes in the radiochemical analysis but problems in low-level radioactivity measurement, environmental-type analyses, and special situations caused in the last years a renaissance of the need for separation techniques. Most of the radiochemical procedures, based on the classic works of the Manhattan Project chemists of the 1940's, were published in the National Nuclear Energy Series (NNES). Improvements such as new solvent extraction and ion exchange separations have been added to these methods throughout the years. Recently the Los Alamos Group have reissued their collected Radiochemical Procedures containing a short summary and review of basic inorganic chemistry - 'Chemistry of the Elements on the Basis of Electronic Configuration'. (A.L.)

  20. Prediction of Local Ultimate Strain and Toughness of Trabecular Bone Tissue by Raman Material Composition Analysis

    Directory of Open Access Journals (Sweden)

    Roberto Carretta

    2015-01-01

    Full Text Available Clinical studies indicate that bone mineral density correlates with fracture risk at the population level but does not correlate with individual fracture risk well. Current research aims to better understand the failure mechanism of bone and to identify key determinants of bone quality, thus improving fracture risk prediction. To get a better understanding of bone strength, it is important to analyze tissue-level properties not influenced by macro- or microarchitectural factors. The aim of this pilot study was to identify whether and to what extent material properties are correlated with mechanical properties at the tissue level. The influence of macro- or microarchitectural factors was excluded by testing individual trabeculae. Previously reported data of mechanical parameters measured in single trabeculae under tension and bending and its compositional properties measured by Raman spectroscopy was evaluated. Linear and multivariate regressions show that bone matrix quality but not quantity was significantly and independently correlated with the tissue-level ultimate strain and postyield work (r=0.65–0.94. Principal component analysis extracted three independent components explaining 86% of the total variance, representing elastic, yield, and ultimate components according to the included mechanical parameters. Some matrix parameters were both included in the ultimate component, indicating that the variation in ultimate strain and postyield work could be largely explained by Raman-derived compositional parameters.

  1. Molar mass of poly(ethylene terephthalate) (PET) during ultimate uniaxial drawing

    NARCIS (Netherlands)

    Göschel, U.; Cools, P.J.C.H.

    2000-01-01

    The changes of the average molar mass Mw, Mn, Mz, and molar mass distributions during multistep uniaxial drawing of poly(ethylene terephthalate) (PET) to achieve ultimate mechanical properties have been studied in detail by means of size exclusion chromatography (SEC) with triple detection:

  2. Molar-Mass of Poly(Ethylene-Terephthalate) (PET) During Ultimate Uniaxial Drawing

    NARCIS (Netherlands)

    Göschel, A.G.P.U.; Cools, P.J.C.H.

    2000-01-01

    The changes of the average molar mass Mw, Mn, Mz, and molar mass distributions during multistep uniaxial drawing of poly(ethylene terephthalate) (PET) to achieve ultimate mechanical properties have been studied in detail by means of size exclusion chromatography (SEC) with triple detection:

  3. Prisoner Fasting as Symbolic Speech: The Ultimate Speech-Action Test.

    Science.gov (United States)

    Sneed, Don; Stonecipher, Harry W.

    The ultimate test of the speech-action dichotomy, as it relates to symbolic speech to be considered by the courts, may be the fasting of prison inmates who use hunger strikes to protest the conditions of their confinement or to make political statements. While hunger strikes have been utilized by prisoners for years as a means of protest, it was…

  4. Reliability analysis of production ships with emphasis on load combination and ultimate strength

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaozhi

    1995-05-01

    This thesis deals with ultimate strength and reliability analysis of offshore production ships, accounting for stochastic load combinations, using a typical North Sea production ship for reference. A review of methods for structural reliability analysis is presented. Probabilistic methods are established for the still water and vertical wave bending moments. Linear stress analysis of a midships transverse frame is carried out, four different finite element models are assessed. Upon verification of the general finite element code ABAQUS with a typical ship transverse girder example, for which test results are available, ultimate strength analysis of the reference transverse frame is made to obtain the ultimate load factors associated with the specified pressure loads in Det norske Veritas Classification rules for ships and rules for production vessels. Reliability analysis is performed to develop appropriate design criteria for the transverse structure. It is found that the transverse frame failure mode does not seem to contribute to the system collapse. Ultimate strength analysis of the longitudinally stiffened panels is performed, accounting for the combined biaxial and lateral loading. Reliability based design of the longitudinally stiffened bottom and deck panels is accomplished regarding the collapse mode under combined biaxial and lateral loads. 107 refs., 76 refs., 37 tabs.

  5. Magnetic surfaces, particle orbits and neutral injection in conventional and ultimate torsatrons

    International Nuclear Information System (INIS)

    Anderson, D.T.; Derr, J.A.; Kruckewitt, T.; Shohet, J.L.; Rehker, S.; Tataronis, J.A.

    1979-01-01

    Capabilities in fully non-axisymmetric numerical methods have resulted in a parametric study of various conventional and ultimate torsatron configurations. No superbananas are found in torsatrons without local magnetic wells. Neutral injection calculations show that, if the vacuum magnetic surfaces are well defined, tangential injection is very efficient

  6. Study of ultimate heat sink to Angra-1,2 and 3 Nuclear Power Plants

    International Nuclear Information System (INIS)

    Moreira, R.M.; Pinto, A.M.F.

    1985-03-01

    This report presents the premises, results and conclusion of study done to ultimate heat sink of Angra 1,2 and 3 units, with base in postulated accidents that generate transient heat discharges to environment. It's explicitily presumed the eventuality of discharging heat water recirculation. (C.M.) [pt

  7. Method for ultimate disposition of borate containing radioactive wastes by vitrification

    International Nuclear Information System (INIS)

    Bege, D.; Faust, H.J.; Puthawala, A.; Stunkel, H.

    1984-01-01

    Method for the ultimate disposition of radioactive wastes by vitrification, in which weak to medium radioactive waste concentrates from borate-containing radioactive liquids are mixed with added glass-forming materials, maximally in a ratio of 1:3, and the mixture heated to obtain a glass-forming melt

  8. 26 CFR 48.6427-10 - Kerosene; claims by registered ultimate vendors (blocked pumps).

    Science.gov (United States)

    2010-04-01

    ... (blocked pumps). 48.6427-10 Section 48.6427-10 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE...; claims by registered ultimate vendors (blocked pumps). (a) Overview. This section provides rules under... allowed by section 6427(l)(5)(B)(i). These claims relate to kerosene sold from a blocked pump. Claims...

  9. Discussion of the Method to Determine the Ultimate Bearing Capacity of Soil Foundation

    Science.gov (United States)

    Du, Peng; Liu, Xiaoling; Zhang, Yangfu

    2017-12-01

    Combining literature examples, this paper has carried out Contrastive analysis of the theoretical formula method and finite element method about the ultimate bearing capacity of foundation, To verify rationality and superiority of the incremental load method in finite element ABAQUS in solving the bearing capacity of foundation soil. The study can provide certain reference for practical engineering calculation and analysis of foundation bearing capacity.

  10. Too many journals? Towards a theory of repeated rejections and ultimate acceptance

    NARCIS (Netherlands)

    Oosterhaven, Jan

    Under a set of reasonable assumptions, it is shown that all manuscripts submitted to any journal will ultimately be published, either by the first journal or by one of the following journals to which a manuscript is resubmitted. This suggests that low quality manuscripts may also be published, which

  11. A comparison of international criteria for the ultimate storage of radioactive wastes

    International Nuclear Information System (INIS)

    Mielke, H.

    1985-01-01

    In countries other than the Federal Republic of Germany and internationally there are no comprehensive codes referring to criteria and safety requirements except those of the IAEA and USA. In other countries there exist safety goals for the ultimate storage or for purely geological criteria. The degree of detailing regulations differs widely abroad and internationally. Safety goals abroad and internationally as well as measures for their realisation in the ultimate storage of radioactive wastes in deep geological formations are in line with the German safety goals. The IAEA refers to general aspects of geological, waste technology and ultimate storage technology criteria. In the USA, ultimate storage technology criteria have been quantified in part. The quantitative geological criteria existing in Great Britain and in the Netherlands are only relevant in as much as safety analyses must be performed for a specific site to provide evidence for the safety of this site. The comparison shows that most requirements pronounced abroad are also made for the Federal Republic of Germany. Some requirements are more specified in the Federal Republic of Germany, some are more detailed abroad. (orig./HP) [de

  12. proximate and ultimate analysis of fuel pellets from oil palm residues

    African Journals Online (AJOL)

    HOD

    Keywords: Oil Palm Residues, Fuel Pellets, Proximate Analysis, Ultimate Analysis. 1. INTRODUCTION ... Pelletizing of this biomass resources into pellets is a way of ensuring a ... demand for pellets [3], and alternative feed-stocks such as palm kernel ... agro-residues, selection of the best pellets has to be made based on ...

  13. 7 CFR 4280.29 - Supplemental financing required for the Ultimate Recipient Project.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Supplemental financing required for the Ultimate Recipient Project. 4280.29 Section 4280.29 Agriculture Regulations of the Department of Agriculture... AND GRANTS Rural Economic Development Loan and Grant Programs § 4280.29 Supplemental financing...

  14. Delayed Auditory Feedback and Movement

    Science.gov (United States)

    Pfordresher, Peter Q.; Dalla Bella, Simone

    2011-01-01

    It is well known that timing of rhythm production is disrupted by delayed auditory feedback (DAF), and that disruption varies with delay length. We tested the hypothesis that disruption depends on the state of the movement trajectory at the onset of DAF. Participants tapped isochronous rhythms at a rate specified by a metronome while hearing DAF…

  15. #FakeNobelDelayReasons

    CERN Multimedia

    2013-01-01

    Tuesday’s hour-long delay of the Nobel Prize in Physics announcement was (and still is) quite the cause for speculation. But on the Twittersphere, it was simply the catalyst for some fantastic puns, so-bad-they're-good physics jokes and other shenanigans. Here are some of our favourite #FakeNobelDelayReasons.    

  16. Picosecond resolution programmable delay line

    International Nuclear Information System (INIS)

    Suchenek, Mariusz

    2009-01-01

    The note presents implementation of a programmable delay line for digital signals. The tested circuit has a subnanosecond delay range programmable with a resolution of picoseconds. Implementation of the circuit was based on low-cost components, easily available on the market. (technical design note)

  17. Delayed primary realignment of posterior urethral rupture | Shittu ...

    African Journals Online (AJOL)

    The treatment of acute posterior urethral rupture is controversial. Twelve patients who presented with acute posterior urethral rupture over a five--year period were treated by delayed primary realignment of the injury. The technique of this procedure and the outcome are the subject of this presentation. Eight patients had ...

  18. Fusion cross sections from measurements of delayed X-rays

    International Nuclear Information System (INIS)

    Pacheco, A.J.; Gregorio, D.E. di; Fernandez Niello, J.O; Elgue, M.

    1988-01-01

    The program XRAY is a FORTRAN 77 computer code for the extraction of fusion cross sections from delayed X-ray measurements. This is accomplished by calculating the theoretical expressions of the time dependence of the evaporation-residue cross sections and taking them as adjustable parameters in a χ 2 minimization procedure. (orig.)

  19. Project delay analysis of HRSG

    Science.gov (United States)

    Silvianita; Novega, A. S.; Rosyid, D. M.; Suntoyo

    2017-08-01

    Completion of HRSG (Heat Recovery Steam Generator) fabrication project sometimes is not sufficient with the targeted time written on the contract. The delay on fabrication process can cause some disadvantages for fabricator, including forfeit payment, delay on HRSG construction process up until HRSG trials delay. In this paper, the author is using semi quantitative on HRSG pressure part fabrication delay with configuration plant 1 GT (Gas Turbine) + 1 HRSG + 1 STG (Steam Turbine Generator) using bow-tie analysis method. Bow-tie analysis method is a combination from FTA (Fault tree analysis) and ETA (Event tree analysis) to develop the risk matrix of HRSG. The result from FTA analysis is use as a threat for preventive measure. The result from ETA analysis is use as impact from fabrication delay.

  20. Delayed radiation neuropathy

    Energy Technology Data Exchange (ETDEWEB)

    Nagashima, T.; Miyamoto, K.; Beppu, H.; Hirose, K.; Yamada, K. (Tokyo Metropolitan Neurological Hospital (Japan))

    1981-07-01

    A case of cervical plexus neuropathy was reported in association with chronic radio-dermatitis, myxedema with thyroid adenoma and epiglottic tumor. A 38-year-old man has noticed muscle weakness and wasting of the right shoulder girdle since age 33. A detailed history taking revealed a previous irradiation to the neck because of the cervical lymphadenopathy at age 10 (X-ray 3,000 rads), keroid skin change at age 19, obesity and edema since 26, and hoarseness at 34. Laryngoscopic examination revealed a tumor on the right vocal cord, diagnosed as benign papilloma by histological study. In addition, there were chronic radio-dermatitis around the neck, primary hypothyroidism with a benign functioning adenoma on the right lobe of the thyroid, the right phrenic nerve palsy and the right recurrent nerve palsy. All these lesions were considered to be the late sequellae of radiation to the neck in childhood. Other neurological signs were weakness and amyotrophy of the right shoulder girdle with patchy sensory loss, and areflexia of the right arm. Gross power was fairly well preserved in the right hand. EMG showed neurogenic changes in the tested muscles, suggesting a peripheral nerve lesion. Nerve conduction velocities were normal. No abnormal findings were revealed by myelography and spinal CT. The neurological findings of the patient were compatible with the diagnosis of middle cervical plexus palsy apparently due to late radiation effect. In the literature eight cases of post-radiation neuropathy with a long latency have been reported. The present case with the longest latency after the radiation should be included in the series of the reported cases of ''delayed radiation neuropathy.'' (author).

  1. Delayed radiation neuropathy

    International Nuclear Information System (INIS)

    Nagashima, Toshiko; Miyamoto, Kazuto; Beppu, Hirokuni; Hirose, Kazuhiko; Yamada, Katsuhiro

    1981-01-01

    A case of cervical plexus neuropathy was reported in association with chronic radio-dermatitis, myxedema with thyroid adenoma and epiglottic tumor. A 38-year-old man has noticed muscle weakness and wasting of the right shoulder girdle since age 33. A detailed history taking revealed a previous irradiation to the neck because of the cervical lymphadenopathy at age 10 (X-ray 3,000 rads), keroid skin change at age 19, obesity and edema since 26, and hoarseness at 34. Laryngoscopic examination revealed a tumor on the right vocal cord, diagnosed as benign papilloma by histological study. In addition, there were chronic radio-dermatitis around the neck, primary hypothyroidism with a benign functioning adenoma on the right lobe of the thyroid, the right phrenic nerve palsy and the right recurrent nerve palsy. All these lesions were considered to be the late sequellae of radiation to the neck in childhood. Other neurological signs were weakness and amyotrophy of the right shoulder girdle with patchy sensory loss, and areflexia of the right arm. Gross power was fairly well preserved in the right hand. EMG showed neurogenic changes in the tested muscles, suggesting a peripheral nerve lesion. Nerve conduction velocities were normal. No abnormal findings were revealed by myelography and spinal CT. The neurological findings of the patient were compatible with the diagnosis of middle cervical plexus palsy apparently due to late radiation effect. In the literature eight cases of post-radiation neuropathy with a long latency have been reported. The present case with the longest latency after the radiation should be included in the series of the reported cases of ''delayed radiation neuropathy.'' (author)

  2. Delayed Single Stage Perineal Posterior Urethroplasty

    International Nuclear Information System (INIS)

    Ali, S.; Shahnawaz; Shahzad, I.; Baloch, M. U.

    2015-01-01

    Objective: To determine the delayed single stage perineal posterior urethroplasty for treatment of posterior urethral stricture/distraction defect. Study Design: Descriptive case series. Place and Duration of Study: Department of Urology, Jinnah Postgraduate Medical Centre, Karachi, from January 2009 to December 2011. Methodology: Patients were selected for delayed single stage perineal posterior urethroplasty for treatment of posterior urethral stricture / distraction defect. All were initially suprapubically catheterized followed by definitive surgery after at least 3 months. Results: Thirty male patients were analyzed with a mean follow-up of 10 months, 2 patients were excluded as they developed failure in first 3 months postoperatively. Mean patients age was 26.25 ± 7.9 years. On follow-up, 7 patients (23.3 percentage) experienced recurrent stricture during first 10 months. Five (16.6 percentage) patients were treated successfully with single direct visual internal urethrotomy. Two patients (6.6 percentage) had more than one direct visual internal urethrotomy and considered failed. Re-do perineal urethroplasty was eventually performed. The overall success rate was 93.3 percentage with permissive criteria allowing single direct visual internal urethrotomy and 76.6% with strict criteria allowing no more procedures postoperatively. Conclusion: Posterior anastomotic urethroplasty offers excellent long-term results to patients with posterior urethral trauma and distraction defect even after multiple prior procedures. (author)

  3. Delayed Single Stage Perineal Posterior Urethroplasty.

    Science.gov (United States)

    Ali, Shahzad; Shahnawaz; Shahzad, Iqbal; Baloch, Muhammad Umar

    2015-06-01

    To determine the delayed single stage perineal posterior urethroplasty for treatment of posterior urethral stricture/distraction defect. Descriptive case series. Department of Urology, Jinnah Postgraduate Medical Centre, Karachi, from January 2009 to December 2011. Patients were selected for delayed single stage perineal posterior urethroplasty for treatment of posterior urethral stricture / distraction defect. All were initially suprapubically catheterized followed by definitive surgery after at least 3 months. Thirty male patients were analyzed with a mean follow-up of 10 months, 2 patients were excluded as they developed failure in first 3 months postoperatively. Mean patient's age was 26.25 ± 7.9 years. On follow-up, 7 patients (23.3%) experienced recurrent stricture during first 10 months. Five (16.6%) patients were treated successfully with single direct visual internal urethrotomy. Two patients (6.6%) had more than one direct visual internal urethrotomy and considered failed. Re-do perineal urethroplasty was eventually performed. The overall success rate was 93.3% with permissive criteria allowing single direct visual internal urethrotomy and 76.6% with strict criteria allowing no more procedures postoperatively. Posterior anastomotic urethroplasty offers excellent long-term results to patients with posterior urethral trauma and distraction defect even after multiple prior procedures.

  4. Attosecond Delays in Molecular Photoionization.

    Science.gov (United States)

    Huppert, Martin; Jordan, Inga; Baykusheva, Denitsa; von Conta, Aaron; Wörner, Hans Jakob

    2016-08-26

    We report measurements of energy-dependent photoionization delays between the two outermost valence shells of N_{2}O and H_{2}O. The combination of single-shot signal referencing with the use of different metal foils to filter the attosecond pulse train enables us to extract delays from congested spectra. Remarkably large delays up to 160 as are observed in N_{2}O, whereas the delays in H_{2}O are all smaller than 50 as in the photon-energy range of 20-40 eV. These results are interpreted by developing a theory of molecular photoionization delays. The long delays measured in N_{2}O are shown to reflect the population of molecular shape resonances that trap the photoelectron for a duration of up to ∼110 as. The unstructured continua of H_{2}O result in much smaller delays at the same photon energies. Our experimental and theoretical methods make the study of molecular attosecond photoionization dynamics accessible.

  5. The Assessment of the Ultimate Hull Girder Strength of RO-RO Ship after Damages

    Science.gov (United States)

    Zubair Muis Alie, Muhammad; Sitepu, Ganding; Izaak Latumahin, Samuel

    2018-03-01

    Many accidents of Ro-Ro ships happen in Indonesia such as collision and grounding. When the collision or grounding takes place on the Ro-Ro ship, the ultimate strength of hull structure after damage becomes decrease. Car and passenger decks are critical location since collision and/or grounding occur. In the present study, the assessment of the ultimate hull girder strength is conducted. The cross section of Ro-Ro ship is taken to be analyzed. The collision and grounding damages are assumed to be palced on the side and bottom area, respectively. The damages are created by removing the element from the side shell and bottom part. Finally, the result obtained is compared with one another.

  6. Accelerator physics and technology limitations to ultimate energy and luminosity in very large hadron colliders

    Energy Technology Data Exchange (ETDEWEB)

    P. Bauer et al.

    2002-12-05

    The following presents a study of the accelerator physics and technology limitations to ultimate energy and luminosity in very large hadron colliders (VLHCs). The main accelerator physics limitations to ultimate energy and luminosity in future energy frontier hadron colliders are synchrotron radiation (SR) power, proton-collision debris power in the interaction regions (IR), number of events-per-crossing, stored energy per beam and beam-stability [1]. Quantitative estimates of these limits were made and translated into scaling laws that could be inscribed into the particle energy versus machine size plane to delimit the boundaries for possible VLHCs. Eventually, accelerator simulations were performed to obtain the maximum achievable luminosities within these boundaries. Although this study aimed at investigating a general VLHC, it was unavoidable to refer in some instances to the recently studied, [2], 200 TeV center-of-mass energy VLHC stage-2 design (VLHC-2). A more thorough rendering of this work can be found in [3].

  7. Ultimate Limit State Model Basis for Assessment of Offshore Wind Energy Converters

    DEFF Research Database (Denmark)

    Thöns, Sebastian; Faber, M. H.; Rücker, W.

    2012-01-01

    then in combina-tion with the ultimate limit state requirements leads to the specific constitutive relations. As a result finite element models based on shell elements incorporating a structural and a loading model are introduced and described in detail. Applying these models the ultimate capacity of the support...... on the basis of literature review and measurement data from a prototype Multibrid M5000 support structure. In combination with the developed structural and loading models, sensitivity analyses in regard to the responses are peiformed to enhance the understanding and to refine the developed models. To this end...... variables on the responses including nonlinearity the refinement of the model is performed on a quantitative basis....

  8. Evaluation of time-accelerated irradiation method of elastomer by modulus-ultimate elongation profile

    International Nuclear Information System (INIS)

    Ito, Masayuki; Oka, Toshitaka; Hama, Yosimasa

    2009-01-01

    'Generalized modulus-ultimate elongation profile' was induced from the relationship between the modulus and the ultimate elongation of an elastomer that was quantitatively added crosslinking and scission. This profile can be used to evaluate the time-accelerated irradiation methods of ethylene-propylene-diene elastomer. The irradiation under low dose rate (0.33 kGy/h) at room temperature was the reference condition. The short-time irradiation condition was 4.2 kGy/h in 0.5 MPa oxygen at room temperature and 5.0 kGy/h in air at 70 o C. The former tended to bring about the higher ratio of scission than the reference condition; the latter tended to bring about the higher ratio of crosslinking.

  9. Out-of-plane ultimate shear strength of RC mat-slab foundations

    International Nuclear Information System (INIS)

    Kumagai, Hitoshi; Nukui, Yasushi; Imamura, Akira; Terayama, Takeshi; Hagiwara, Tetsuya; Kojima, Isao

    2011-01-01

    There have been few studies on the out-of-plane shear in RC mat-slab foundations, and the reasonable method has been demanded to estimate ultimate shear strength of RC mat-slab foundations in the nuclear facilities. In the previous study, the out-of-plane loading tests on the 20 square slab specimens had been performed to collect the fundamental data. In this study, the test results were successfully predicted by 3D non-linear Finite Element Analysis. It has been confirmed that the ultimate shear stress in the slab specimen can be estimated by the Arakawa's formula, which is commonly used to estimate the shear strength of RC beams. (author)

  10. Ultimate analysis of PWR prestressed concrete containment subjected to internal pressure

    International Nuclear Information System (INIS)

    Hu, H.-T.; Lin, Y.-H.

    2006-01-01

    Numerical analyses are carried out by using the ABAQUS finite element program to predict the ultimate pressure capacity and the failure mode of the PWR prestressed concrete containment at Maanshan nuclear power plant. Material nonlinearity such as concrete cracking, tension stiffening, shear retention, concrete plasticity, yielding of prestressing tendon, yielding of steel reinforcing bar and degradation of material properties due to high temperature are all simulated with proper constitutive models. Geometric nonlinearity due to finite deformation has also been considered. The results of the analysis show that when the prestressed concrete containment fails, extensive cracks take place at the apex of the dome, the junction of the dome and cylinder, and the bottom of the cylinder connecting to the base slab. In addition, the ultimate pressure capacity of the containment is higher than the design pressure by 86%

  11. Nonlinear finite element analysis of nuclear reinforced prestressed concrete containments up to ultimate load capacity

    International Nuclear Information System (INIS)

    Gupta, A.; Singh, R.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1996-01-01

    For safety evaluation of nuclear structures a finite element code ULCA (Ultimate Load Capacity Assessment) has been developed. Eight/nine noded isoparametric quadrilateral plate/shell element with reinforcement as a through thickness discrete but integral smeared layer of the element is presented to analyze reinforced and prestressed concrete structures. Various constitutive models such as crushing, cracking in tension, tension stiffening and rebar yielding are studied and effect of these parameters on the reserve strength of structures is brought out through a number of benchmark tests. A global model is used to analyze the prestressed concrete containment wall of a typical 220 MWe Pressurized Heavy Water Reactor (PHWR) up to its ultimate capacity. This demonstrates the adequacy of Indian PHWR containment design to withstand severe accident loads

  12. Exponential stability of switched linear systems with time-varying delay

    Directory of Open Access Journals (Sweden)

    Satiracoo Pairote

    2007-11-01

    Full Text Available We use a Lyapunov-Krasovskii functional approach to establish the exponential stability of linear systems with time-varying delay. Our delay-dependent condition allows to compute simultaneously the two bounds that characterize the exponential stability rate of the solution. A simple procedure for constructing switching rule is also presented.

  13. Comparison of apical leakage between immediate versus delayed post space preparation using two resin sealers

    Directory of Open Access Journals (Sweden)

    Priyanka Kaushal Kalra

    2009-01-01

    Full Text Available Post & Core Procedures have became an integral part of a dentist′s arsenal. This study was carried out in order to assess the microleakage when immediate and delayed post space preparations were done using resin sealers. Immediate post space preparations showed lesser apical leakage as opposed to delayed post space preparation.

  14. Break-before-make CMOS inverter for power-efficient delay implementation.

    Science.gov (United States)

    Puhan, Janez; Raič, Dušan; Tuma, Tadej; Bűrmen, Árpád

    2014-01-01

    A modified static CMOS inverter with two inputs and two outputs is proposed to reduce short-circuit current in order to increment delay and reduce power overhead where slow operation is required. The circuit is based on bidirectional delay element connected in series with the PMOS and NMOS switching transistors. It provides differences in the dynamic response so that the direct-path current in the next stage is reduced. The switching transistors are never ON at the same time. Characteristics of various delay element implementations are presented and verified by circuit simulations. Global optimization procedure is used to obtain the most power-efficient transistor sizing. The performance of the modified CMOS inverter chain is compared to standard implementation for various delays. The energy (charge) per delay is reduced up to 40%. The use of the proposed delay element is demonstrated by implementing a low-power delay line and a leading-edge detector cell.

  15. 75 FR 13238 - Processed Raspberry Promotion, Research, and Information Order; Delay of Referendum

    Science.gov (United States)

    2010-03-19

    ... Promotion, Research, and Information Order; Delay of Referendum AGENCY: Agricultural Marketing Service... further modifications to its proposal. FOR FURTHER INFORMATION CONTACT: Kimberly Coy, Marketing Specialist... Part 1208 Administrative practice and procedure, Advertising, Consumer information, Marketing...

  16. An existence theorem for a type of functional differential equation with infinite delay

    NARCIS (Netherlands)

    Izsak, F.

    We prove an existence theorem for a functional differential equation with infinite delay using the Schauder fixpoint theorem. We extend a result in [19] applying the fixed point procedure in an appropriate function space.

  17. Qualtum cosmics-and-chaotics--the ultimate tortoise in physics and modern medicine.

    Directory of Open Access Journals (Sweden)

    Kothari M

    1997-10-01

    Full Text Available Qualtum cosmics is the qualitative opposite of quantum mechanics. The flip-side of qualtum cosmics is qualtum chaotics, the two governing much of what is seen as inscrutable in medicine. The Ultimate (Last Tortoise is close to Einsteinean idea of a Unified Theory, a single concept that can explain whatsoever there is in physics, (and in medicine, or what have you.

  18. Utilization of metal scrap for the production of waste drums for ultimate disposal

    International Nuclear Information System (INIS)

    Janberg, K.; Rittscher, D.

    1988-01-01

    The contribution reviews the history of development of the techniques for treatment of decommissioning scrap from the beginning of the 1980's onwards (decommissioning of the Niederaichbach and Gundremmingen nuclear power stations), together with the radiological measuring methods required for regulatory purposes. The advantages of the recycling of the metal scrap by means of melting, and of materials utilization for production of waste containers for ultimate storage are discussed together with product quality assurance criteria. (RB) [de

  19. The ultimate safe (US) Reactor: A concept for the third millenium

    International Nuclear Information System (INIS)

    Gat, U.

    1986-01-01

    The Ultimate Safe (U.S.) Reactor is based on a novel safety concept. Fission products in the reactor are allowed to accumulate only to a level at which they would constitute a harmless source term. Removal of fission products also removes the decay heat - the driving force for the source term. The reactor has no excess criticality and is controlled by the reactivity temperature coefficient. Safety is inherent and passive. Waste is removed from the site promptly

  20. Modeling and simulation of loss of the ultimate heat sink in a typical material testing reactor

    International Nuclear Information System (INIS)

    El-Khatib, Hisham; El-Morshedy, Salah El-Din; Higazy, Maher G.; El-Shazly, Karam

    2013-01-01

    Highlights: ► A thermal–hydraulic model has been developed to simulate loss of the ultimate heat sink in MTR. ► The model involves three coupled sub-models for core, heat exchanger and cooling tower. ► The model is validated against PARET for steady-state and verified by operation data for transients. ► The model is used to simulate the behavior of the reactor under a loss of the ultimate heat sink. ► The model results are analyzed and discussed. -- Abstract: A thermal–hydraulic model has been developed to simulate loss of the ultimate heat sink in a typical material testing reactor (MTR). The model involves three interactively coupled sub-models for reactor core, heat exchanger and cooling tower. The model is validated against PARET code for steady-state operation and verified by the reactor operation records for transients. Then, the model is used to simulate the thermal–hydraulic behavior of the reactor under a loss of the ultimate heat sink event. The simulation is performed for two operation regimes: regime I representing 11 MW power and three cooling tower cells operated, and regime II representing 22 MW power and six cooling tower cells operated. In regime I, the simulation is performed for 1, 2 and 3 cooling tower cells failed while in regime II, it is performed for 1, 2, 3, 4, 5 and 6 cooling tower cells failed. The simulation is performed under protected conditions where the safety action called power reduction is triggered by reactor protection system to decrease the reactor power by 20% when the coolant inlet temperature to the core reaches 43 °C and scram is triggered if the core inlet temperature reaches 44 °C. The model results are analyzed and discussed.

  1. Tasks of radiation protection in the centralized collection and ultimate disposal of radioactive waste

    International Nuclear Information System (INIS)

    Boerst, F.M.; Fasten, C.; Koerner, W.; Oppermann, U.; Werner, H.J.; Zappe, D.

    1988-01-01

    In the GDR, the ERAM (Endlager fuer radioaktive Abfaelle, Morsleben), an operating unit of Volkseigenes Kombinat Kernkraftwerke 'Bruno Leuschner' in Greifswald, is responsible for the central collection and ultimate disposal of radioactive waste. From the licensing body's point of view an assessment is given of the legislation for radioactive wastes, especially as to their collection, transport to and handling in the final repository. As a result, some conclusions are drawn concerning future work in this field. 9 tabs., 34 refs. (author)

  2. Effects of urbanization on animal behaviour : patterns, underlying mechanisms and ultimate causes

    OpenAIRE

    Miranda, Ana Catarina Sequeira Nunes Coutinho de

    2014-01-01

    Human-altered environmental conditions affect many species at the global scale. An extreme form of anthropogenic alteration is the existence and rapid increase of urban areas. A key question is how animals cope with urbanization. In order to live in cities, animals have to adjust their behaviour and life histories to the urban novel environment.The main objectives of this thesis were to investigate (i) the existence of behavioural changes related to the urbanization process, (ii) the ultimate...

  3. Dual characteristics of yield and ultimate strength as applied to two grades of beryllium

    International Nuclear Information System (INIS)

    Priddy, T.G.; Benzley, S.E.; Johnson, R.L.

    1977-02-01

    Published yield and ultimate biaxial strength data for two grades of beryllium are correlated with the use of a macroscopic failure model. Cross sections of the resulting surfaces in three-dimensional stress space are drawn to illustrate the expected transition from ductile to brittle fracture for triaxial tension states of stress. The usefulness of these models to the prediction of fracture in ductile materials is discussed. 5 tables, 8 figures, 11 references

  4. Numerical Study on Ultimate Behaviour of Bolted End-Plate Steel Connections

    Directory of Open Access Journals (Sweden)

    R.E.S. Ismail

    Full Text Available Abstract Bolted end-plate steel connections have become more popular due to ease of fabrication. This paper presents a three dimension Finite Element Model (FEM, using the multi-purpose software ABAQUS, to study the effect of different geometrical parameters on the ultimate behavior of the connection. The proposed model takes into account material and geometrical non-linearities, initial imperfection, contact between adjacent surfaces and the pretension force in the bolts. The Finite Element results are calibrated with published experimental results ''briefly reviewed in this paper'' and verified that the numerical model can simulate and analyze the overall and detailed behavior of different types of bolted end-plate steel connections. Using verified FEM, parametric study is then carried out to study the ultimate behavior with variations in: bolt diameter, end-plate thickness, length of column stiffener, angle of rib stiffener. The results are examined with respect to the failure modes, the evolution of the resistance, the initial stiffness, and the rotation capacity. Finally, the ultimate behavior of the bolted end-plate steel connection is discussed in detail, and recommendations for the design purpose are made.

  5. Methodology for predicting ultimate pressure capacity of the ACR-1000 containment structure

    International Nuclear Information System (INIS)

    Saudy, A.M.; Awad, A.; Elgohary, M.

    2006-01-01

    The Advanced CANDU Reactor or the ACR-1000 is developed by Atomic Energy of Canada Limited (AECL) to be the next step in the evolution of the CANDU product line. It is based on the proven CANDU technology and incorporates advanced design technologies. The ACR containment structure is an essential element of the overall defense in depth approach to reactor safety, and is a physical barrier against the release of radioactive material to the environment. Therefore, it is important to provide a robust design with an adequate margin of safety. One of the key design requirements of the ACR containment structure is to have an ultimate pressure capacity that is at least twice the design pressure Using standard design codes, the containment structure is expected to behave elastically at least up to 1.5 times the design pressure. Beyond this pressure level, the concrete containment structure with reinforcements and post-tension tendons behaves in a highly non-linear manner and exhibits a complex response when cracks initiate and propagate. To predict the structural non-linear responses, at least two critical features are involved. These are: the structural idealization by the geometry and material property models, and the adopted solution algorithm. Therefore, detailed idealization of the concrete structure is needed in order to accurately predict its ultimate pressure capacity. This paper summarizes the analysis methodology to be carried out to establish the ultimate pressure capacity of the ACR containment structure and to confirm that the structure meets the specified design requirements. (author)

  6. Transition to the Ultimate Regime in Two-Dimensional Rayleigh-Bénard Convection

    Science.gov (United States)

    Zhu, Xiaojue; Mathai, Varghese; Stevens, Richard J. A. M.; Verzicco, Roberto; Lohse, Detlef

    2018-04-01

    The possible transition to the so-called ultimate regime, wherein both the bulk and the boundary layers are turbulent, has been an outstanding issue in thermal convection, since the seminal work by Kraichnan [Phys. Fluids 5, 1374 (1962), 10.1063/1.1706533]. Yet, when this transition takes place and how the local flow induces it is not fully understood. Here, by performing two-dimensional simulations of Rayleigh-Bénard turbulence covering six decades in Rayleigh number Ra up to 1 014 for Prandtl number Pr =1 , for the first time in numerical simulations we find the transition to the ultimate regime, namely, at Ra*=1013 . We reveal how the emission of thermal plumes enhances the global heat transport, leading to a steeper increase of the Nusselt number than the classical Malkus scaling Nu ˜Ra1 /3 [Proc. R. Soc. A 225, 196 (1954), 10.1098/rspa.1954.0197]. Beyond the transition, the mean velocity profiles are logarithmic throughout, indicating turbulent boundary layers. In contrast, the temperature profiles are only locally logarithmic, namely, within the regions where plumes are emitted, and where the local Nusselt number has an effective scaling Nu ˜Ra0.38 , corresponding to the effective scaling in the ultimate regime.

  7. Ultimate strength analysis of ring-stiffened cylinders subjected to hydrostatic pressure

    International Nuclear Information System (INIS)

    Park, Chi Mo

    1990-01-01

    In this study, ultimate strength analysis of ring-stiffened cylinders have been performed, considering the elasto-plastic large deflection. In the elasto-plastic analysis, von Mises yield criteria, the plastic flow theory and the layered approach have been adopted. In order to take into account the follower force effect of the hydrostatic pressure, the incremental load components have been updated at every loading step. As collapse modes, axisymmetric yielding, interframe shell buckling and general buckling are considered, while local buckling of ring-stiffener is not considered. Initial shape imperfection is assumed to be the elastic buckling mode to obtain the lower bound of the ultimate strength. Results of numerical analysis are compared with the experimental results to show the validity of the present approach. It has been drawn that the present numerical results are closely correlated with the experimental results. On the other hand, the effects of initial shape imperfection and condition on the ultimate strength have been investigated. (Author)

  8. Ultimate load design and testing of a cylindrical prestressed concrete vessel

    International Nuclear Information System (INIS)

    Stefanou, G.D.

    1982-01-01

    The object of this research was to design, construct and test to failure a prestressed concrete pressure vessel model that could be used to investigate the behavior of a full scale structure underworking and ultimate load. The properties and the design of the model was based generally on full scale vessels already constructed to house the nuclear reactors used in atomic power stations. To design the model the ultimate load approach was adopted throughout. All load factors associated with the prestressing have been defined and kept to a minimum in order that the vessel's behavior may be predicted. The tests on the vessel were carried out first on the elastic range to observe its behavior at working load and then at the ultimate range to observe the modes of failure and compare the actual results in both cases with the predicted values. Although full agreement between observed results and predicted values was not obtained, the conclusions drawn from the study were useful for the design of full scale vessels. (author)

  9. Delays and networked control systems

    CERN Document Server

    Hetel, Laurentiu; Daafouz, Jamal; Johansson, Karl

    2016-01-01

    This edited monograph includes state-of-the-art contributions on continuous time dynamical networks with delays. The book is divided into four parts. The first part presents tools and methods for the analysis of time-delay systems with a particular attention on control problems of large scale or infinite-dimensional systems with delays. The second part of the book is dedicated to the use of time-delay models for the analysis and design of Networked Control Systems. The third part of the book focuses on the analysis and design of systems with asynchronous sampling intervals which occur in Networked Control Systems. The last part of the book exposes several contributions dealing with the design of cooperative control and observation laws for networked control systems. The target audience primarily comprises researchers and experts in the field of control theory, but the book may also be beneficial for graduate students. .

  10. Linear rotary optical delay lines

    Science.gov (United States)

    Guerboukha, Hichem; Qu, Hang; Skorobogatiy, Maksim

    2016-03-01

    We present a semi-analytical solution for the design of a high-speed rotary optical delay line that use a combination of two rotating curvilinear reflectors. We demonstrate that it is possible to design an infinite variety of the optical delay lines featuring linear dependence of the optical delay on the rotation angle. This is achieved via shape optimization of the rotating reflector surfaces. Moreover, a convenient spatial separation of the incoming and outgoing beams is possible. For the sake of example, we present blades that fit into a circle of 10cm diameter. Finally, a prototype of a rotary delay line is fabricated using CNC machining, and its optical properties are characterized.

  11. Systematics in delayed neutron yields

    Energy Technology Data Exchange (ETDEWEB)

    Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan). Atomic Energy Research Inst.

    1998-03-01

    An attempt was made to reproduce the systematic trend observed in the delayed neutron yields for actinides on the basis of the five-Gaussian representation of the fission yield together with available data sets for delayed neutron emission probability. It was found that systematic decrease in DNY for heavier actinides is mainly due to decrease of fission yields of precursors in the lighter side of the light fragment region. (author)

  12. Isolating behavioral mechanisms of intertemporal choice: nicotine effects on delay discounting and amount sensitivity.

    Science.gov (United States)

    Locey, Matthew L; Dallery, Jesse

    2009-03-01

    Many drugs of abuse produce changes in impulsive choice, that is, choice for a smaller-sooner reinforcer over a larger-later reinforcer. Because the alternatives differ in both delay and amount, it is not clear whether these drug effects are due to the differences in reinforcer delay or amount. To isolate the effects of delay, we used a titrating delay procedure. In phase 1, 9 rats made discrete choices between variable delays (1 or 19 s, equal probability of each) and a delay to a single food pellet. The computer titrated the delay to a single food pellet until the rats were indifferent between the two options. This indifference delay was used as the starting value for the titrating delay for all future sessions. We next evaluated the acute effects of nicotine (subcutaneous 1.0, 0.3, 0.1, and 0.03 mg/kg) on choice. If nicotine increases delay discounting, it should have increased preference for the variable delay. Instead, nicotine had very little effect on choice. In a second phase, the titrated delay alternative produced three food pellets instead of one, which was again produced by the variable delay (1 s or 19 s) alternative. Under this procedure, nicotine increased preference for the one pellet alternative. Nicotine-induced changes in impulsive choice are therefore likely due to differences in reinforcer amount rather than differences in reinforcer delay. In addition, it may be necessary to include an amount sensitivity parameter in any mathematical model of choice when the alternatives differ in reinforcer amount.

  13. Misdiagnosis of Child Abuse Related to Delay in Diagnosing a Paediatric Brain Tumour

    Directory of Open Access Journals (Sweden)

    Lynne Wrennall Ph.D.

    2008-01-01

    Full Text Available Conflicting opinion regarding the relative weight that should be allocated to the investigation of organic causes of child illness, compared to the pursuit of suspicions of child abuse, has generated considerable public debate. The discourse of Munchausen Syndrome by Proxy/Fabricated and Induced Illness is at the centre of contention. In particular, concern has arisen that children's medical needs are being neglected when their conditions are misdiagnosed as child abuse. This paper documents a case study in which the use of Child Protection procedures was linked to the belief that the child's illness had “no organic cause.” The case study is contextualised in a review of literature relevant to the diagnostic process. The deployment of the Child Protection perspective resulted in significant delay in the diagnosis of the child's brain tumour. The child was ultimately found to be suffering from an optic chasm mass lesion involving the hypothalamus and the medial temporal regions, resulting in Diencephalic Syndrome. The evidence in this case is that erring on the side of suspecting Munchausen Syndrome by Proxy/Fabricated and Induced Illness, was not “erring on the side of the child.” Several lessons need to be learned from the case. The importance of ensuring that the Child Protection perspective does not displace adequate assessment of alternative explanations for the child's condition is emphasised, as is the need for good communication in medical relationships. Strategies involving empathy, mediation, negotiation and conflict resolution may provide a more appropriate and therapeutic alternative to the use of Child Protection procedures in cases where the diagnosis is contentious. The need to re-write relevant policy, protocols and guidance is imperative.

  14. Analytical applications for delayed neutrons

    International Nuclear Information System (INIS)

    Eccleston, G.W.

    1983-01-01

    Analytical formulations that describe the time dependence of neutron populations in nuclear materials contain delayed-neutron dependent terms. These terms are important because the delayed neutrons, even though their yields in fission are small, permit control of the fission chain reaction process. Analytical applications that use delayed neutrons range from simple problems that can be solved with the point reactor kinetics equations to complex problems that can only be solved with large codes that couple fluid calculations with the neutron dynamics. Reactor safety codes, such as SIMMER, model transients of the entire reactor core using coupled space-time neutronics and comprehensive thermal-fluid dynamics. Nondestructive delayed-neutron assay instruments are designed and modeled using a three-dimensional continuous-energy Monte Carlo code. Calculations on high-burnup spent fuels and other materials that contain a mix of uranium and plutonium isotopes require accurate and complete information on the delayed-neutron periods, yields, and energy spectra. A continuing need exists for delayed-neutron parameters for all the fissioning isotopes

  15. Analog Group Delay Equalizers Design Based on Evolutionary Algorithm

    Directory of Open Access Journals (Sweden)

    M. Laipert

    2006-04-01

    Full Text Available This paper deals with a design method of the analog all-pass filter designated for equalization of the group delay frequency response of the analog filter. This method is based on usage of evolutionary algorithm, the Differential Evolution algorithm in particular. We are able to design such equalizers to be obtained equal-ripple group delay frequency response in the pass-band of the low-pass filter. The procedure works automatically without an input estimation. The method is presented on solving practical examples.

  16. Adolescent Pregnancy and Its Delay.

    Science.gov (United States)

    Bell, Lloyd H.

    This paper examines some probable reasons for the black adolescent male's contribution to increased pregnancy in the black community. Using a situation analysis, it presents the following testable suppositions: (1) black males' fear of retribution for impregnating a girl has diminished, leading to increased sexual intercourse and ultimately to…

  17. Impact of leakage delay on bifurcation in high-order fractional BAM neural networks.

    Science.gov (United States)

    Huang, Chengdai; Cao, Jinde

    2018-02-01

    The effects of leakage delay on the dynamics of neural networks with integer-order have lately been received considerable attention. It has been confirmed that fractional neural networks more appropriately uncover the dynamical properties of neural networks, but the results of fractional neural networks with leakage delay are relatively few. This paper primarily concentrates on the issue of bifurcation for high-order fractional bidirectional associative memory(BAM) neural networks involving leakage delay. The first attempt is made to tackle the stability and bifurcation of high-order fractional BAM neural networks with time delay in leakage terms in this paper. The conditions for the appearance of bifurcation for the proposed systems with leakage delay are firstly established by adopting time delay as a bifurcation parameter. Then, the bifurcation criteria of such system without leakage delay are successfully acquired. Comparative analysis wondrously detects that the stability performance of the proposed high-order fractional neural networks is critically weakened by leakage delay, they cannot be overlooked. Numerical examples are ultimately exhibited to attest the efficiency of the theoretical results. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Pretreatment procedures

    International Nuclear Information System (INIS)

    Anon.

    1989-01-01

    It is frequently in the patient's best interest that radiation treatments are initiated soon after the decision to treat is made. However, it is essential to good radiation therapy that the patient's treatment course be planned and beam-modifying devices be fabricated with utmost care prior to treatment. The objectives of the treatment, along with the treatment parameters and techniques necessary to achieve these objectives, must be discussed prior to initiating planning procedures. Determination of the target volume is made by the radiation oncologist; this is based on knowledge of the history of the tumor, the patterns of spread of the disease, and on diagnostic findings during the work-up of each patient. It is then necessary to obtain several measurements of the patient and also to identify the position of the target volume and of adjacent normal organs with respect to known external skin marks before the actual treatment planning is begun. Such localization can be done through several methods. The two most commonly used methods are radiographic and computed tomography (CT), both of which are discussed in this chapter. The measurements often include contours of the patient's external surface, usually in the axial plane of the central axis of the beam, and often in multiple levels within the region to be treated. Three dimensional localization and treatment planning requires thorough understanding of geometry as well as of patient positioning and immobilization. This chapter attempts to clarify some of these complicated but essential preparations for treatment

  19. 15 CFR Supplement No. 3 to Part 748 - BIS-711, Statement by Ultimate Consignee and Purchaser Instructions

    Science.gov (United States)

    2010-01-01

    ...” include: contractual, franchise, distributor, wholesaler, continuing and regular individual business, etc... persons, other than employees of the ultimate consignee or purchaser, who assisted in the preparation of...

  20. Parametric Study on Ultimate Failure Criteria of Elbow Piping Components in Seismically Isolated NPP

    Energy Technology Data Exchange (ETDEWEB)

    Hahm, Dae Gi; Ki, Min Kyu [KAERI, Daejeon (Korea, Republic of); Jeon, Bub Gyu; Kim, Nam Sik [Pusan National University, Busan (Korea, Republic of)

    2016-05-15

    It is well known that the interface pipes between isolated and non-isolated structures will become the most critical in the seismically isolated NPPs. Therefore, seismic performance of such interface pipes should be evaluated comprehensively especially in terms of the seismic fragility capacity. To evaluate the seismic capacity of interface pipes in the isolated NPP, firstly, we should define the failure mode and failure criteria of critical pipe components. Hence, in this study, we performed the dynamic tests of elbow components which were installed in a seismically isolated NPP, and evaluated the ultimate failure mode and failure criteria by using the test results. To do this, we manufactured 25 critical elbow component specimens and performed cyclic loading tests under the internal pressure condition. The failure mode and failure criteria of a pipe component will be varied by the design parameters such as the internal pressure, pipe diameter, loading type, and loading amplitude. From the tests, we assessed the effects of the variation parameters onto the failure criteria. For the tests, we generated the seismic input protocol of relative displacement between the ends of elbow component. In this paper, elbow in piping system was defined as a fragile element and numerical model was updated by component test. Failure mode of piping component under seismic load was defined by the dynamic tests of ultimate pipe capacity. For the interface piping system, the seismic capacity should be carefully estimated since that the required displacement absorption capacity will be increased significantly by the adoption of the seismic isolation system. In this study, the dynamic tests were performed for the elbow components which were installed in an actual NPPs, and the ultimate failure mode and failure criteria were also evaluated by using the test results.

  1. Measurement of delayed neutron-emitting fission products in nuclear reactor coolant water during reactor operation

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The method covers the detection and measurement of delayed neutron-emitting fission products contained in nuclear reactor coolant water while the reactor is operating. The method is limited to the measurement of the delayed neutron-emitting bromine isotope of mass 87 and the delayed neutron-emitting iodine isotope of mass 137. The other delayed neutron-emitting fission products cannot be accurately distinguished from nitrogen 17, which is formed under some reactor conditions by neutron irradiation of the coolant water molecules. The method includes a description of significance, measurement variables, interferences, apparatus, sampling, calibration, standardization, sample measurement procedures, system efficiency determination, calculations, and precision

  2. Ultimate pressures achieved in TiZrV sputter-coated vacuum chambers

    CERN Document Server

    Benvenuti, Cristoforo; Ruzinov, V

    2001-01-01

    Two metre long, cylindrical vacuum chambers of diameter ranging from 34 to 100 mm, coated with TiZrV getter films by sputtering, have been baked for about 24 h at temperatures from 120 to 250 degrees C. The ultimate pressures achieved after bakeout were found to correspond to the ratio of the pressure gauge degassing to the effective pumping speed provided by the chamber at the location of the gauge. The results covering a pressure range from 10/sup -11/ Torr down to 10 /sup -13/ Torr are presented and discussed. (6 refs).

  3. DHC in Helsinki - The Ultimate Heating and Cooling Solution for a Large Urban Area

    Energy Technology Data Exchange (ETDEWEB)

    Wirgentius, Niko; Riipinen, Marko

    2010-09-15

    Since the 1950s there has been successful district energy business in Helsinki. It has been the main factor for superior energy efficiency and low CO2 emissions both in heating and cooling as well as providing clean air for the metropolitan area. The system has been grown by commercial basis based on customers' own willingness to select district energy solution. It also provided a profitable energy business to local energy company, Helsinki Energy. Helsinki DHC system is a good example of ultimate urban energy solution that provides benefits for the customer, energy company, metropolitan area and for the whole society as well.

  4. Investigations on the ultimate compressive strength of composite plates with geometrical imperfections

    DEFF Research Database (Denmark)

    Misirlis, K.; Downes, J.; Dow, R.S.

    2009-01-01

    with initial geometric imperfections. This paper presents the validation of finite element models against a series of plate tests that were performed within this framework and parametric studies that were carried out to identify the effects of geometric imperfections on the ultimate compressive strength......A series of studies has been performed within the MARSTRUCT Network of Excellence on Marine Structures in order to investigate the buckling response of glass fibre reinforced polymer plates. These studies include the fabrication, testing and finite element analysis of a large number of plates...

  5. Lava ultimate resin nano ceramic for CAD/ CAM: customization case study.

    Science.gov (United States)

    Koller, M; Arnetzl, G V; Holly, L; Arnetzl, G

    2012-01-01

    Lava Ultimate Resin Nano Ceramic (RNC) blocks are innovative new CAD/CAM materials that make it possible to achieve superior esthetic results in easy steps. The blocks are made of nano ceramic particles embedded in a highly cured resin matrix. Therefore, composite materials can be used to characterize and adjust resin nano ceramic restorations after milling. The milled RNC restorations can be individualized intra-orally or extra-orally, either before or after insertion. Unlike conventional ceramic restorations, customization and glaze firing is neither necessary nor possible with RNC restorations. This opens up the opportunity for intraoral individualization and adaptation of the restorations.

  6. Reflecting on impact, changes and continuities: restructuring workplace cultures: the ultimate work-family challenge.

    OpenAIRE

    Lewis, Suzan

    2010-01-01

    Purpose – The purpose of this paper is to reflect on the paper “Restructuring workplace cultures: the ultimate work-family challenge?” is published in Women in Management Review, Vol. 16 No. 1, 2001, pp. 21-9. \\ud \\ud Design/methodology/approach – The impact of the paper is considered within a framework that takes account of national discursive and political contexts in the UK in 2001 and in the present and uses a gendered organisation lens. \\ud \\ud Findings – The 2001 paper demonstrates that...

  7. The legal ensurance of underground ultimate storage of radioactive wastes without risk

    International Nuclear Information System (INIS)

    Prasse, R.

    1974-01-01

    1. The legal position towards the property owner: a) with a view to the freedom of property claim, b) in the light of the influence of the property owner. 2. The legal position towards the neighbouring property owners: a) resistance rights of the body corporate responsible for the ultimate storage, b) resistance rights of the neighbouring property owner. 3. The legal position towards those authorized to mine: a) mining free minerals, b) mining minerals reserved for the state. 4. The legal position towards prospectors. (orig./HP) [de

  8. Seismic proving test of ultimate piping strength (current status of preliminary tests)

    International Nuclear Information System (INIS)

    Suzuki, K.; Namita, Y.; Abe, H.; Ichihashi, I.; Suzuki, K.; Ishiwata, M.; Fujiwaka, T.; Yokota, H.

    2001-01-01

    In 1998 Fiscal Year, the 6 year program of piping tests was initiated with the following objectives: i) to clarify the elasto-plastic response and ultimate strength of nuclear piping, ii) to ascertain the seismic safety margin of the current seismic design code for piping, and iii) to assess new allowable stress rules. In order to resolve extensive technical issues before proceeding on to the seismic proving test of a large-scale piping system, a series of preliminary tests of materials, piping components and simplified piping systems is intended. In this paper, the current status of the material tests and the piping component tests is reported. (author)

  9. A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

    OpenAIRE

    Ali Asghar Khodayari

    2013-01-01

    One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing...

  10. UWB delay and multiply receiver

    Energy Technology Data Exchange (ETDEWEB)

    Dallum, Gregory E.; Pratt, Garth C.; Haugen, Peter C.; Romero, Carlos E.

    2013-09-10

    An ultra-wideband (UWB) delay and multiply receiver is formed of a receive antenna; a variable gain attenuator connected to the receive antenna; a signal splitter connected to the variable gain attenuator; a multiplier having one input connected to an undelayed signal from the signal splitter and another input connected to a delayed signal from the signal splitter, the delay between the splitter signals being equal to the spacing between pulses from a transmitter whose pulses are being received by the receive antenna; a peak detection circuit connected to the output of the multiplier and connected to the variable gain attenuator to control the variable gain attenuator to maintain a constant amplitude output from the multiplier; and a digital output circuit connected to the output of the multiplier.

  11. Langevin approach to synchronization of hyperchaotic time-delay dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Budini, Adrian A [Consejo Nacional de Investigaciones CientIficas y Tecnicas, Centro Atomico Bariloche, Av. E Bustillo Km 9.5, (8400) Bariloche (Argentina); Consortium of the Americas for Interdisciplinary Science and Department of Physics and Astronomy, University of New Mexico, Albuquerque, NM 87131 (United States)

    2008-11-07

    In this paper, we characterize the synchronization phenomenon of hyperchaotic scalar nonlinear delay dynamics in a fully-developed chaos regime. Our results rely on the observation that, in that regime, the stationary statistical properties of a class of hyperchaotic attractors can be reproduced with a linear Langevin equation, defined by replacing the nonlinear delay force by a delta-correlated noise. Therefore, the synchronization phenomenon can be analytically characterized by a set of coupled Langevin equations. We apply this formalism to study anticipated synchronization dynamics subject to external noise fluctuations as well as for characterizing the effects of parameter mismatch in a hyperchaotic communication scheme. The same procedure is applied to second-order differential delay equations associated with synchronization in electro-optical devices. In all cases, the departure with respect to perfect synchronization is measured through a similarity function. Numerical simulations in discrete maps associated with the hyperchaotic dynamics support the formalism.

  12. The theoretical ultimate magnetoelectric coefficients of magnetoelectric composites by optimization design

    International Nuclear Information System (INIS)

    Wang, H.-L.; Liu, B.

    2014-01-01

    This paper investigates what is the largest magnetoelectric (ME) coefficient of ME composites, and how to realize it. From the standpoint of energy conservation, a theoretical analysis is carried out on an imaginary lever structure consisting of a magnetostrictive phase, a piezoelectric phase, and a rigid lever. This structure is a generalization of various composite layouts for optimization on ME effect. The predicted theoretical ultimate ME coefficient plays a similar role as the efficiency of ideal heat engine in thermodynamics, and is used to evaluate the existing typical ME layouts, such as the parallel sandwiched layout and the serial layout. These two typical layouts exhibit ME coefficient much lower than the theoretical largest values, because in the general analysis the stress amplification ratio and the volume ratio can be optimized independently and freely, but in typical layouts they are dependent or fixed. To overcome this shortcoming and achieve the theoretical largest ME coefficient, a new design is presented. In addition, it is found that the most commonly used electric field ME coefficient can be designed to be infinitely large. We doubt the validity of this coefficient as a reasonable ME effect index and consider three more ME coefficients, namely the electric charge ME coefficient, the voltage ME coefficient, and the static electric energy ME coefficient. We note that the theoretical ultimate value of the static electric energy ME coefficient is finite and might be a more proper measure of ME effect

  13. Experimental study on ultimate strength and strain behavior of concrete under biaxial compressive stresses

    International Nuclear Information System (INIS)

    Onuma, Hiroshi; Aoyagi, Yukio

    1976-01-01

    The purpose of this investigation was to study the ultimate strength failure mode and deformation behavior of concrete under short-term biaxial compressive stresses, as an aid to design and analyze the concrete structures subjected to multiaxial compression such as prestressed or reinforced concrete vessel structures. The experimental work on biaxial compression was carried out on the specimens of three mix proportions and different ages with 10cm x 10cm x 10cm cubic shape in a room controlled at 20 0 C. The results are summarized as follows. (1) To minimize the surface friction between specimens and loading platens, the pads of teflon sheets coated with silicone grease were used. The coefficient of friction was measured and was 3 percent on the average. (2) The test data showed that the strength of the concrete subjected to biaxial compression increased as compared to uniaxial compressive strength, and that the biaxial strength increase was mainly dependent on the ratio of principal stresses, and it was hardly affected by mix proportions and ages. (3) The maximum increase of strength, which occurred at the stress ratio of approximately sigma 2 /sigma 1 = 0.6, was about 27 percent higher than the uniaxial strength of concrete. (4) The ultimate strength in case of biaxial compression could be approximated by the parabolic equation. (Kako, I.)

  14. Secondary Moments due to Prestressing with Different Bond at the Ultimate Limit State

    Directory of Open Access Journals (Sweden)

    Halvoník Jaroslav

    2018-03-01

    Full Text Available Secondary effects of prestressing develop in statically indeterminate structures (e.g., continuous beams due to the restraint of deformations imposed by hyperstatic restraints. These effects may significantly influence internal forces and stresses in prestressed structures. Secondary effects are influenced by the redundancy of a structural system, which raises the question of whether they will remain constant after a change in the structural system, e.g., due to the development of plastic hinge(s in a critical cross-section(s or after the development of a kinematic mechanism, or if they will disappear when the structure changes into a sequence of simply supported beams. The paper deals with an investigation of the behavior of continuous post-tensioned beams subjected to an ultimate load with significant secondary effects from prestressing. A total of 6 two-span beams prestressed by tendons with different bonds were tested in a laboratory with a load that changed their structural system into a kinematic mechanism. The internal forces and secondary effects of the prestressing were controlled through measurements of the reactions in all the supports. The results revealed that the secondary effects remained as a permanent part of the action on the experimental beams, even after the development of the kinematic mechanism. The results obtained confirmed that secondary effects should be included in all combinations of actions for verifications of ultimate limit states (ULS.

  15. Secondary Moments due to Prestressing with Different Bond at the Ultimate Limit State

    Science.gov (United States)

    Halvoník, Jaroslav; Pažma, Peter; Vida, Radoslav

    2018-03-01

    Secondary effects of prestressing develop in statically indeterminate structures (e.g., continuous beams) due to the restraint of deformations imposed by hyperstatic restraints. These effects may significantly influence internal forces and stresses in prestressed structures. Secondary effects are influenced by the redundancy of a structural system, which raises the question of whether they will remain constant after a change in the structural system, e.g., due to the development of plastic hinge(s) in a critical cross-section(s) or after the development of a kinematic mechanism, or if they will disappear when the structure changes into a sequence of simply supported beams. The paper deals with an investigation of the behavior of continuous post-tensioned beams subjected to an ultimate load with significant secondary effects from prestressing. A total of 6 two-span beams prestressed by tendons with different bonds were tested in a laboratory with a load that changed their structural system into a kinematic mechanism. The internal forces and secondary effects of the prestressing were controlled through measurements of the reactions in all the supports. The results revealed that the secondary effects remained as a permanent part of the action on the experimental beams, even after the development of the kinematic mechanism. The results obtained confirmed that secondary effects should be included in all combinations of actions for verifications of ultimate limit states (ULS).

  16. Application of risk-informed design methods to select the PSACS ultimate heat sink

    International Nuclear Information System (INIS)

    Elliott, Michael A.; Apostolakis, George E.

    2009-01-01

    In the early phases of advanced system design, information is scarce. The technologies, components and processes to be used have not been specified adequately or are not well understood and uncertainties are very large. Yet, it is during these early phases that design teams and other stakeholders are required to make critical decisions to guide the development of the system. To aid in this decision making, a formal process is proposed based on the Analytic-Deliberative Decision-Making Process (ADP) that allows stakeholders to synthesize rationally their knowledge and experience and facilitate learning and sharing of best practices. The ADP identifies and prioritizes attributes relevant to a decision problem and supports the formulation of metrics to measure the performance of different design options. This paper reports on an application of the ADP to the selection of an ultimate heat sink for the Flexible Conversion Ratio (FCR) reactor's Passive Secondary Auxiliary Cooling System (PSACS). Two ultimate heat sink options are identified and evaluated, air and water.

  17. Plasticity and constraints on social evolution in African mole-rats: ultimate and proximate factors.

    Science.gov (United States)

    Faulkes, Chris G; Bennett, Nigel C

    2013-05-19

    Here, we review comparative studies of African mole-rats (family Bathyergidae) to explain how constraints acting at the ultimate (environmental) and proximate (organismal) levels have led to convergent gains and losses of sociality within this extensive adaptive radiation of subterranean rodents endemic to sub-Saharan Africa. At the ultimate level, living in environments that range from mesic through to arid has led to both variation and flexibility in social organization among species, culminating in the pinnacle of social evolution in the eusocial naked and Damaraland mole-rats (Heterocephalus glaber and Fukomys damarensis). The common mole-rat (Cryptomys hottentotus) provides a model example of how plasticity in social traits exists within a single species inhabiting areas with different ecological constraint. At the proximate level, reproductive strategies and cooperative breeding may be constrained by the correlated evolution of a suite of traits including physiological suppression of reproduction, the development of physiological and morphological castes, and the mode of ovulatory control and seasonality in breeding. Furthermore, recent neurobiological advances indicate that differential patterns of neurotransmitter expression within the forebrain may underpin (and limit) either a solitary or group living/cooperative lifestyle not only in mole-rats, but also more widely among disparate mammalian taxa.

  18. Evaluation of the ultimate pressure capacity of rectangular HVAC ducts for nuclear pwoer plants

    International Nuclear Information System (INIS)

    Wedellsborg, B.W.

    1984-01-01

    Typical Category I HVAC ducts in a nuclear plant must be designed for loads and load combinations including positive and negative pressure loads which are generated due to the normal operation and postulated accident conditions. These pressure loads most often govern the design of the HVAC ducts. Structural design criteria are presently based on the AISI Code which limits the duct panel width-to-thickness ratio to a maximum of 500 and the maximum height-to-thickness ratio to 200, unless it can be shown by structural tests that larger ratios can be used. Test Programs performed on rectangular HVAC ducts subjected to vacumm loads have substantiated the use of ducts having panel width to thickness ratios of up to 1600. The results of the test programs were subsequently incorporated into the design through a more rational analytical design method which was developed from and correlates well with the test results. The purpose of this paper is to present the analytical design method and its correlation with the test results. Simple formulae for the design of rectangular HVAC ducts are presented. Lower bound values of duct sheet, and stiffener ultimate loads are derived, and correlated with recent test results. Analytically predicted ultimate pressures are also compared with other available duct test data

  19. ULtiMATE system for rapid assembly of customized TAL effectors.

    Directory of Open Access Journals (Sweden)

    Junjiao Yang

    Full Text Available Engineered TAL-effector nucleases (TALENs and TALE-based constructs have become powerful tools for eukaryotic genome editing. Although many methods have been reported, it remains a challenge for the assembly of designer-based TALE repeats in a fast, precise and cost-effective manner. We present an ULtiMATE (USER-based Ligation Mediated Assembly of TAL Effector system for speedy and accurate assembly of customized TALE constructs. This method takes advantage of uracil-specific excision reagent (USER to create multiple distinct sticky ends between any neighboring DNA fragments for specific ligation. With pre-assembled templates, multiple TALE DNA-binding domains could be efficiently assembled in order within hours with minimal manual operation. This system has been demonstrated to produce both functional TALENs for effective gene knockout and TALE-mediated gene-specific transcription activation (TALE-TA. The feature of both ease-of-operation and high efficiency of ULtiMATE system makes it not only an ideal method for biologic labs, but also an approach well suited for large-scale assembly of TALENs and any other TALE-based constructions.

  20. Ultimate shearing strength of aseismatic walls with many small holes for reactor buildings

    International Nuclear Information System (INIS)

    Yoshizaki, Seiji; Ezaki, Tetsuro; Korenaga, Takeyoshi; Sotomura, Kentaro.

    1984-01-01

    The aseismatic walls for reactor buildings have complicated forms, and are characterized by large wall thickness and high reinforcement ratio as compared with ordinary aseismatic walls. The forms are mainly box, cylinder or irregular polygonal prism and their combination. The design of the walls with many small holes has been performed on the basis of the reinforced concrete structure calculation standard of the Architectural Institute of Japan, following the case with large opening. When there are many small holes, the arrangement of reinforcement for the openings becomes complex, and the construction is difficult. It is necessary to rationalize the design and to simplify the reinforcement work. Under the background like this, the experiment to examine the shearing property in bending of the aseismatic walls with many small holes for reactor buildings was carried out, and horizontal loading test was performed on 43 specimens. The method of calculating the ultimate shearing strength of a wall without opening was proposed, and the method of applying it to a wall with many small holes is shown. The experimental method and the results, the examination of the experimental results, and the ultimate shearing strength of the aseismatic walls are reported. (Kako, I.)

  1. Ultimate strength performance of tankers associated with industry corrosion addition practices

    Directory of Open Access Journals (Sweden)

    Kim Do Kyun

    2014-09-01

    Full Text Available In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR, Common Structural Rules (CSR, and harmonised Common Structural Rules (CSRH are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS, and Time-Dependent Corrosion Wastage Model (TDCWM. To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures

  2. Ultimate strength performance of tankers associated with industry corrosion addition practices

    Directory of Open Access Journals (Sweden)

    Do Kyun Kim

    2014-09-01

    Full Text Available In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR, Common Structural Rules (CSR, and harmonised Common Structural Rules (CSRH are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS, and Time-Dependent Corrosion Wastage Model (TDCWM. To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures.

  3. A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

    Directory of Open Access Journals (Sweden)

    Ali Asghar Khodayari

    2013-12-01

    Full Text Available One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing ultimate pit limits. Some of these methods, such as floating cone algorithm, are heuristic and do not guarantee to generate optimum pit limits. Other methods, like Lerchs–Grossmann algorithm, are rigorous and always generate the true optimum pit limits. In this paper, a new rigorous algorithm is introduced. The main logic in this method is that only positive blocks, which can pay costs of their overlying non-positive blocks, are able to appear in the final pit. Those costs may be paid either by positive block itself or jointly with other positive blocks, which have the same overlying negative blocks. This logic is formulated using a network model as a Linear Programming (LP problem. This algorithm can be applied to two- and three-dimension block models. Since there are many commercial programs available for solving LP problems, pit limits in large block models can be determined easily by using this method.

  4. Chaos in the delay logistic equation with discontinuous delays

    International Nuclear Information System (INIS)

    Sen, Ayan; Mukherjee, Debasis

    2009-01-01

    This paper analyzes a delay logistic equation which models a feedback control problem. Interval map associated to the system is derived. By calculating Lyapunov exponent, we indicate stable orbit and chaotic phenomenon respectively. The results are verified through computer simulation. We identify the parameter which controls the dynamics.

  5. Postraumatic delayed loss of vision

    International Nuclear Information System (INIS)

    Partington, C.R.; Graves, V.B.; Ruetenacht, D.A.; Weinstein, J.M.; Strother, C.M.

    1989-01-01

    The imaging studies and clinical findings in 10 patients who suffered delayed vision loss beginning 1 day to 13 years after head trauma have been reviewed. Two different primary lesions could be identified: pseudoaneurysm of the internal carotid artery and carotid cavernous fistula. The pathologic changes associated with pseudoaneurysm included compression of the optic nerves and/or chiasm by arterial aneurysm and intracranial hematoma. Carotid cavernous fistula caused delayed vision loss by compression of the optic nerves and chiasm by saccular dilatation of the cavernous sinus and by abnormal orbital venous drainage with retinal venous stasis, retinal edema, and glaucoma

  6. Time delayed Ensemble Nudging Method

    Science.gov (United States)

    An, Zhe; Abarbanel, Henry

    Optimal nudging method based on time delayed embedding theory has shows potentials on analyzing and data assimilation in previous literatures. To extend the application and promote the practical implementation, new nudging assimilation method based on the time delayed embedding space is presented and the connection with other standard assimilation methods are studied. Results shows the incorporating information from the time series of data can reduce the sufficient observation needed to preserve the quality of numerical prediction, making it a potential alternative in the field of data assimilation of large geophysical models.

  7. Delayed wound healing after forefoot surgery in patients with rheumatoid arthritis.

    Science.gov (United States)

    Ishie, Shinichiro; Ito, Hiromu; Azukizawa, Masayuki; Furu, Moritoshi; Ishikawa, Masahiro; Ogino, Hiroko; Hamamoto, Yosuke; Matsuda, Shuichi

    2015-05-01

    To elucidate the systemic and local risk factors and the effect of surgical procedures for delayed wound healing after forefoot surgery in patients with rheumatoid arthritis (RA). Fifty forefoot surgeries were performed in 39 patients using resection arthroplasty or a joint-preserving procedure (25 feet for each procedure). The associations between the occurrence of delayed wound healing and clinical variables, radiological assessment, or surgical procedures were analyzed. Delayed wound healing was recorded in nine feet of eight patients. The duration of RA was significantly longer in the delayed healing group than that in the healed group. Age, sex, smoking history, concomitant diabetes, and RA medication did not differ between the groups. Radiological evaluation showed significant differences between groups in metatarsophalangeal dorsal flexion angle. The shortened length of the fourth and the fifth metatarsal bones affected the occurrence of the complication. The joint-preserving procedure had significantly less delayed wound healing compared with resection arthroplasty. Preoperative dorsoplantar deformity and perioperative tissue damage can cause delayed wound healing after forefoot surgery in RA patients.

  8. 49 CFR 236.563 - Delay time.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Delay time. 236.563 Section 236.563 Transportation... Cab Signal Systems Rules and Instructions; Locomotives § 236.563 Delay time. Delay time of automatic... requirements of § 236.24 shall take into consideration the delay time. ...

  9. Long-term experience in salt mining and experience in salt mine decommissioning - a chance for ultimate storage?

    International Nuclear Information System (INIS)

    Sitz, P.; Rauche, H.

    2003-01-01

    The author discusses similarities between salt mining and ultimate storage and the possibility of using abandoned salt mines as ultimate storage site. He states that with all the numeric prediction tools now available, expert knowledge of mining engineers is still indispensable [de

  10. Delayed Development of Pneumothorax After Pulmonary Radiofrequency Ablation

    International Nuclear Information System (INIS)

    Clasen, Stephan; Kettenbach, Joachim; Kosan, Bora; Aebert, Hermann; Schernthaner, Melanie; Kroeber, Stefan-Martin; Boemches, Andrea; Claussen, Claus D.; Pereira, Philippe L.

    2009-01-01

    Acute pneumothorax is a frequent complication after percutaneous pulmonary radiofrequency (RF) ablation. In this study we present three cases showing delayed development of pneumothorax after pulmonary RF ablation in 34 patients. Our purpose is to draw attention to this delayed complication and to propose a possible approach to avoid this major complication. These three cases occurred subsequent to 44 CT-guided pulmonary RF ablation procedures (6.8%) using either internally cooled or multitined expandable RF electrodes. In two patients, the pneumothorax, being initially absent at the end of the intervention, developed without symptoms. One of these patients required chest drain placement 32 h after RF ablation, and in the second patient therapy remained conservative. In the third patient, a slight pneumothorax at the end of the intervention gradually increased and led into tension pneumothorax 5 days after ablation procedure. Underlying bronchopleural fistula along the coagulated former electrode track was diagnosed in two patients. In conclusion, delayed development of pneumothorax after pulmonary RF ablation can occur and is probably due to underlying bronchopleural fistula, potentially leading to tension pneumothorax. Patients and interventionalists should be prepared for delayed onset of this complication, and extensive track ablation following pulmonary RF ablation should be avoided.

  11. Health care quality, access, cost, workforce, and surgical education: the ultimate perfect storm.

    Science.gov (United States)

    Schwartz, Marshall Z

    2012-01-01

    The discussions on health care reform over the past two years have focused on cost containment while trying to maintain quality of care. Focusing on just cost and quality unfortunately does not address other very important factors that impact on our health care delivery system. Availability of a well-trained workforce, maintaining the sophisticated medical/surgical education system, and ultimately access to quality care by the public are critical to maintaining and enhancing our health care delivery system. Unfortunately, all five of these components are under at risk. Thus, we have evolving the ultimate perfect storm affecting our health care delivery system. Although not ideal and given the uniqueness of our population and their expectations, our current delivery system is excellent compared to other countries. However, the cost of our current system is rising at an alarming rate. Currently, health care consumes 17% of our gross domestic product. If our system is not revised this will continue to rise and by 2025 it will consume 48%. The dilemma, given the current state of our overall economy and rising debt, is how to address this major problem. Unfortunately, the Affordable Care Act, which is now law, does not address most of the issues and the cost was initially grossly under estimated. Furthermore, the law does not address the issues of workforce, maintaining our medical education system or ultimately, access. A major revision of our system will be necessary to truly create a system that protects and enhances all five of the components of our health care delivery system. To effectively accomplish this will require addressing those issues that lead to wasteful spending and diversion of our health care dollars to profit instead of care. Improved and efficient delivery systems that reduce complications, reduction of duplication of tertiary and quaternary programs or services within the same markets (i.e. regionalization of care), health insurance reform, and

  12. Early-delayed radiation rhombencephalopathy

    International Nuclear Information System (INIS)

    Nightingale, S.; Dawes, P.J.D.K.; Cartlidge, N.E.F.; Newcastle upon Tyne Univ.

    1982-01-01

    A 37-year-old woman developed an early-delayed rhombencephalopathy 7 weeks after completing a course of radiotherapy to a glomus jugulare tumour. The clinical features, comprising nystagmus, skew strabismus, unilateral facial weakness, dysarthria and ataxia, are compared with four previously reported patients with this syndrome. (author)

  13. Another definition for time delay

    International Nuclear Information System (INIS)

    Narnhofer, H.

    1980-01-01

    Time delay is defined by geometrical considerations which work in classical as well as in quantum mechanics, and its connection with the S-matrix and the virial is proven for potentials with V(x vector) and x vector V(x vector) vanishing as rsup(-1-epsilon) for r -> infinity. (Author)

  14. Weather delay costs to trucking.

    Science.gov (United States)

    2012-11-01

    Estimates of the nations freight sector of transportation range to upwards of $600 billion of total gross domestic product with 70 percent of total value and 60 percent of total weight moving by truck. Weather-related delays can add significantly ...

  15. Diagnostic Delay in Rheumatoid Arthritis

    DEFF Research Database (Denmark)

    Mølbaek, Karen; Hørslev-Petersen, Kim; Primdahl, Jette

    2016-01-01

    BACKGROUND: To prevent joint damage among patients with rheumatoid arthritis (RA), there is a need to minimize delays from the onset of symptoms until the initiation of appropriate therapy. The present study explored the factors that have an impact on the time it takes for Danish patients with RA...

  16. Design flaw could delay collider

    CERN Multimedia

    Cho, Adrian

    2007-01-01

    "A magnet for the Large Hadron Collider (LHC) failed during a key test at the European particle physics laboratory CERN last week. Physicists and engineers will have to repair the damaged magnet and retrofit others to correct the underlynig design flaw, which could delay the start-up of the mammouth subterranean machine." (1,5 page)

  17. Concurrent Delay in Construction Disputes

    DEFF Research Database (Denmark)

    Cavaleri, Sylvie Cécile

    the delay is contractually defined as a contractor's risk, the contractor is liable to pay liquidated damages to the employer; if it is not, the contractor can under certain circumstances claim an extension of time and in some cases also economic compensation from the employer. The situation where a given...

  18. Deconstructing delayed posttraumatic stress disorder

    NARCIS (Netherlands)

    Smid, G

    2011-01-01

    According to the Diagnostic and Statistical Manual of Mental Disorders, delayed posttraumatic stress disorder (PTSD) must be diagnosed in individuals fulfilling criteria for PTSD if the onset of symptoms is at least six months after the trauma. The purpose of this thesis was to establish the

  19. Livermore blasted for project delay

    CERN Multimedia

    1999-01-01

    In a 12 page report issued last week, a review committee set up by the University of California has concluded that mismanagement and poor planning are to blame for significant cost overruns and delays in the construction of NIF, the worlds largest laser (1 page).

  20. Providing delay guarantees in Bluetooth

    NARCIS (Netherlands)

    Ait Yaiz, R.; Heijenk, Geert; Titsworth, F.

    2003-01-01

    Bluetooth polling, also referred to as Bluetooth MAC scheduling or intra-piconet scheduling, is the mechanism that schedules the traffic between the participants in a Bluetooth network. Hence, this mechanism is highly determining with respect to the delay packets experience in a Bluetooth network.

  1. First-Case Operating Room Delays: Patterns Across Urban Hospitals of a Single Health Care System

    Directory of Open Access Journals (Sweden)

    Callie M. Cox Bauer

    2016-08-01

    Full Text Available Purpose: Operating room delays decrease health care system efficiency and increase costs. To improve operating room efficiency in our system, we retrospectively investigated delay frequencies, causes and costs. Methods: We studied all first-of-the-day nonemergent surgical cases performed at three high-volume urban hospitals of a large health system from July 2012 to November 2013. Times for patient flow from arrival to procedure start and documented reasons for delay were obtained from electronic medical records. Delay was defined as patient placement in the operating room later than scheduled surgery time. Effects of patient characteristics, late patient arrival to the hospital, number of planned procedures, years of surgeon experience, service department and hospital facility on odds of delay were examined using logistic regression. Results: Of 5,598 cases examined, 88% were delayed. Patients arrived late to the hospital (surgery in 65% of first cases. Mean time from arrival to scheduled surgery and in-room placement was 104.6 and 127.4 minutes, respectively. Mean delay time was 28.2 minutes. Nearly 60% of delayed cases had no documented reason for delay. For cases with documentation, causes included the physician (52%, anesthesia (15%, patient (13%, staff (9%, other sources (6% and facility (5%. Regression analysis revealed age, late arrival, department and facility as significant predictors of delay. Estimated delay costs, based on published figures and representing lost revenue, were $519,388. Conclusions: To improve operating room efficiency, multidisciplinary strategies are needed for increasing patient adherence to recommended arrival times, documentation of delay by medical staff and consistency in workflow patterns among facilities and departments.

  2. The ecological rationality of delay tolerance: insights from capuchin monkeys.

    Science.gov (United States)

    Addessi, Elsa; Paglieri, Fabio; Focaroli, Valentina

    2011-04-01

    Both human and non-human animals often face decisions between options available at different times, and the capacity of delaying gratification has usually been considered one of the features distinguishing humans from other animals. However, this characteristic can widely vary across individuals, species, and types of task and it is still unclear whether it is accounted for by phylogenetic relatedness, feeding ecology, social structure, or metabolic rate. To disentangle these hypotheses, we evaluated temporal preferences in capuchin monkeys, South-American primates that, despite splitting off from human lineage approximately 35 million years ago, show striking behavioural analogies with the great apes. Then, we compared capuchins' performance with that of the other primate species tested so far with the same procedure. Overall, capuchins showed a delay tolerance significantly higher than closely related species, such as marmosets and tamarins, and comparable to that shown by great apes. Capuchins' tool use abilities might explain their comparatively high preference for delayed options in inter-temporal choices. Moreover, as in humans, capuchin females showed a greater delay tolerance than males, possibly because of their less opportunistic foraging style. Thus, our results shed light on the evolutionary origins of self-control supporting explanations of delay tolerance in terms of feeding ecology. Copyright © 2010 Elsevier B.V. All rights reserved.

  3. Delay Discounting: Pigeon, Rat, Human – Does it Matter?

    Science.gov (United States)

    Vanderveldt, Ariana; Oliveira, Luís; Green, Leonard

    2016-01-01

    Delay discounting refers to the decrease in subjective value of an outcome as the time to its receipt increases. Across species and situations, animals discount delayed rewards, and their discounting is well-described by a hyperboloid function. The current review begins with a comparison of discounting models and the procedures used to assess delay discounting in nonhuman animals. We next discuss the generality of discounting, reviewing the effects of different variables on the degree of discounting delayed reinforcers by nonhuman animals. Despite the many similarities in discounting observed between human and nonhuman animals, several differences have been proposed (e.g., the magnitude effect; nonhuman animals discount over a matter of seconds whereas humans report willing to wait months, if not years before receiving a reward), raising the possibility of fundamental species differences in intertemporal choice. After evaluating these differences, we discuss delay discounting from an adaptationist perspective. The pervasiveness of discounting across species and situations suggests it is a fundamental process underlying decision making. PMID:26881899

  4. Choice between delayed food and immediate oxycodone in rats.

    Science.gov (United States)

    Secci, Maria E; Factor, Julie A; Schindler, Charles W; Panlilio, Leigh V

    2016-12-01

    The choice to seek immediate drug effects instead of more meaningful but delayed rewards is a defining feature of addiction. To develop a rodent model of this behavior, we allowed rats to choose between immediate intravenous delivery of the prescription opioid oxycodone (50 μg/kg) and delayed delivery of palatable food pellets. Rats preferred food at delays up to 30 s, but they chose oxycodone and food equally at 60-s delay and preferred oxycodone over food at 120-s delay. Comparison of food-drug choice, food-only, and drug-only conditions indicated that food availability decreased drug intake, but drug availability increased food intake. In the food-only condition, food was effective as a reinforcer even when delayed by 120 s. Pre-session feeding with chow slowed acquisition of food and drug self-administration, but did not affect choice. To establish procedures for testing potential anti-addiction medications, noncontingent pre-treatment with oxycodone or naltrexone (analogous to substitution and antagonist therapies, respectively) were tested on a baseline in which oxycodone was preferred over delayed food. Naltrexone pre-treatment decreased drug intake and increased food intake. Oxycodone pre-treatment decreased drug intake, but also produced extended periods with no food or drug responding. These findings show that the contingencies that induce preference for drugs over more meaningful but less immediate rewards in humans can be modeled in rodents, and they suggest that the model could be useful for assessing the therapeutic potential of treatments and exploring the underlying behavioral and neural mechanisms involved in addiction.

  5. Controlling uncertain neutral dynamic systems with delay in control input

    International Nuclear Information System (INIS)

    Park, Ju H.; Kwon, O.

    2005-01-01

    This article gives a novel criterion for the asymptotic stabilization of the zero solutions of a class of neutral systems with delays in control input. By constructing Lyapunov functionals, we have obtained the criterion which is expressed in terms of matrix inequalities. The solutions of the inequalities can be easily solved by efficient convex optimization algorithms. A numerical example is included to illustrate the design procedure of the proposed method

  6. Answering the ultimate question "what is the proximal cause of aging?".

    Science.gov (United States)

    Blagosklonny, Mikhail V

    2012-12-01

    Recent discoveries suggest that aging is neither driven by accumulation of molecular damage of any cause, nor by random damage of any kind. Some predictions of a new theory, quasi-programmed hyperfunction, have already been confirmed and a clinically-available drug slows aging and delays diseases in animals. The relationship between diseases and aging becomes easily apparent. Yet, the essence of aging turns out to be so startling that the theory cannot be instantly accepted and any possible arguments are raised for its disposal. I discuss that these arguments actually support a new theory. Are any questions remaining? And might accumulation of molecular damage still play a peculiar role in aging?

  7. Ultimate storage of spent fuel elements of the AVR test power station in the Asse salt mine

    International Nuclear Information System (INIS)

    Wolf, J.

    1975-02-01

    With regard to the ultimate storage of irradiated AVR pebble-bed reactor carbide fuel elements in the saline of Asse, a number of tests and calculations are presented to demonstrate that there is no credible possibility of the MCA (maximum credible accident) defined for the saline. The safety of persons is not threatened during the operation of spent fuel storage nor at any later time (extrapolation up to approx. 1,000 years after storage). 1,000 fuel elements at a time are packed up in gas-tight containers which are stacked in boreholes. The boreholes are then sealed with concrete. Lay-out and functions of the special airlock and transportation systems - from the packing of the containers in a hot cell to the final storage in the borehole - are described with special reference to aspects of the safety of the overall procedure. The possible accidents in the mine are discussed in detail. 85 Kr and T release rates are determined in laboratory tests by heating of the spherical fuel elements. Tests with fuel elements embedded in salt or stagnant brine were carried out at varies temperatures to investigate their behaviour in final storage. Kr and T release, extraction of fission products, mechanical resistance and corrosion were examined in these tests. Finally, the permeability of salt and salt concrete to radioactive gases were investigated in a special experimental arrangement. The diffusion and permeability coefficients obtained for 85 Kr, HT and HTO allow an estimation of the gas discharge of the stored fuel element. (RB/AK) [de

  8. Aging characteristics of containment building and sensitivity on ultimate pressure capacity

    International Nuclear Information System (INIS)

    Seo, Jeong Moon; Choun, Young Sun; Choi, In Kil; Ha, Jae Joo

    1998-03-01

    For the reliable safety assessment of the containment building, structural and material conditions can be investigated in detail and pertinent assessment technologies have to be established. Also, an understanding on the aging-related degradations for the construction materials is required to predict long-term structural safety of the containment building. For the development of reliable aging prediction models, an extensive data base system related to aging properties of the containment building has to be prepared. The objectives of this research are to develop aging models representing long-term degradation of materials and a structural performance assessment program for containment building considering aging-related degradation. According to the results of sensitivity analysis, as the mechanical properties of the constituent materials degrade, the ultimate pressure capacity of containment building may decrease and severe damage may occur around the mid-level of the containment wall. (author). 28 refs., 11 tabs., 36 figs

  9. Ultimate Limit State Design Of Sheet Pile Walls By Finite Elements And Nonlinear Programming

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Damkilde, Lars; Krabbenhøft, Sven

    2002-01-01

    Limit analysis has been used for decades in civil and mechanical engineering practice as a means of analyzing structures of materials which with reasonable accuracy can be described as being rigid-perfectly plastic. Such materials include steel, concrete and soils. Traditionally, most attention has...... been given to the problem which consists of determining the ultimate magnitude of a given set of loads acting on a structure with a given geometry. This problem is relevant when determining e.g. the necessary extrusion pressure in metal forming problems, when evaluating the bearing capacity...... is the load intensity. In the paper we consider the latter of these problems with particular reference to the design of sheet pile walls....

  10. Patient dose rate: An ultimate limit for spatial and density resolution of scanning systems

    International Nuclear Information System (INIS)

    Kowalski, G.; Wagner, W.

    1979-01-01

    In X-ray scanning systems, picture quality of the reconstructed slices is limited to a maximum spatial as well as density resolution by the applied radiation dose. Density resolution can be improved in proportion to the root of the patient dose, whereas a doubled spatial resolving power requires an eight times higher patient dose, assuming a fixed slice thickness. Only a careful trade-off between the applied patient dose, density resolution and spatial resolution yields a maximal diagnostic value for the physician. Specifications of a scanning system have to take into account these ultimate restrictions, so that picture quality really is limited by the patient's dose rather than by technical constraints. In addition a method is given by which the applied dose can be reduced by focusing the main intensity onto the region of interest, in case that region is known a priori. (orig.) [de

  11. Methodological Challenges of Identifying Ultimate Land Use Changes Caused by Biofuel Production

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Kløverpris, Jesper; Nielsen, Per Henning

    2007-01-01

    that is only poorly dealt with by LCA methods. Even though the use of land, or change of land cover and its eco-systems, is acknowledged to be a very important impact of human activities, a methodology for assessing this impact category has not yet  been properly developed within LCA. Some LCA scientists have...... looked into methods for assessing the impacts of given changes of land use, i.e. the impact assessment component of the LCA, but very few have looked into how to actually do the inventory modelling, i.e. how to identify which land is ultimately affected by the decision and system under study. State...... in the systems being studied. The aims of this paper is to analyse the mechanisms influencing the long-term land use consequences of changes in crop demand and propose a methodological framework for identifying these consequences within a global scope. The outset of the paper is the principles of consequential...

  12. SoundScapes - Beyond Interaction... in search of the ultimate human-centred interface

    DEFF Research Database (Denmark)

    Brooks, Tony

    2006-01-01

    that can also benefit communication. To achieve this a new generation of intuitive natural interfaces will be required and SoundScapes (see below) is a step toward this goal to discover the ultimate interface for matching the human experience to technology. Emergent hypothesis that have developed...... as a result of the SoundScapes research will be discussed. Introduction to SoundScapes SoundScapes is a contemporary art concept that has become widely known as an interdisciplinary platform for knowledge exchange, innovative product creation of creative and scientific work that uses non-invasive sensor...... Resonance. The multimedia content is adaptable so that the environment is tailored for each participant according to a user profile. This full body movement or the smallest of gesture results in human data input to SoundScapes. The same technology that enables this empowerment is used for performance art...

  13. An experimental investigation on the ultimate strength of epoxy repaired braced partial infilled RC frames

    Science.gov (United States)

    Dubey, Shailendra Kumar Damodar; Kute, Sunil

    2014-09-01

    Due to earthquake, buildings are damaged partially or completely. Particularly structures with soft storey are mostly affected. In general, such damaged structures are repaired and reused. In this regard, an experimental investigation was planned and conducted on models of single-bay, single-storey of partial concrete infilled reinforced concrete (RC) frames up to collapse with corner, central and diagonal steel bracings. Such collapsed frames were repaired with epoxy resin and retested. The initiative was to identify the behaviour, extent of restored ultimate strength and deflection of epoxy-retrofitted frames in comparison to the braced RC frames. The performance of such frames has been considered only for lateral loads. In comparison to bare RC frames, epoxy repaired partial infilled frames have significant increase in the lateral load capacity. Central bracing is more effective than corner and diagonal bracing. For the same load, epoxy repaired frames have comparable deflection than similar braced frames.

  14. Silicon coupled-ring resonator structures for slow light applications: potential, impairments and ultimate limits

    International Nuclear Information System (INIS)

    Canciamilla, A; Torregiani, M; Ferrari, C; Morichetti, F; Melloni, A; De La Rue, R M; Samarelli, A; Sorel, M

    2010-01-01

    Coupled-ring resonator-based slow light structures are reported and discussed. By combining the advantages of high index contrast silicon-on-insulator technology with an efficient thermo-optical activation, they provide an on-chip solution with a bandwidth of up to 100 GHz and a slowdown factor of up to 16, as well as a continuous reconfiguration scheme and a fine tunability. The performance of these devices is investigated in detail for both static and dynamic operation, in order to evaluate their potential in optical signal processing applications at high bit rate. The main impairments imposed by fabrication imperfections are also discussed in relation to the slowdown factor. In particular, the analysis of the impact of backscatter, disorder and two-photon absorption on the device transfer function reveals the ultimate limits of these structures and provides valuable design rules for their optimization

  15. Process for extracting residual heat and device for the ultimate absorption of heat for nuclear reactors

    International Nuclear Information System (INIS)

    Bernard, Lawrence Jr.

    1980-01-01

    This invention concerns a 'heat sink' or device for the ultimate absorption of heat for electric power stations using the most widespread thermal neutron nuclear reactors, namely 'light water' reactors such as boiling or pressurized water reactors. The residual heat given off by these reactors can be safely extracted with this method by using dry cooling. However, the invention does not concern the problems arising from the cooling of the steam used for actuating the steam turbine nor the cooling of the steam exhausted by the turbine or coming from it, but it does concern the 'safety' part of the nuclear power station in which the residual heat discharged in the reactor is controlled and dissipated [fr

  16. Design proposal for ultimate shear strength of tapered steel plate girders

    Directory of Open Access Journals (Sweden)

    A. Bedynek

    2017-03-01

    Full Text Available Numerous experimental and numerical studies on prismatic plate girders subjected to shear can be found in the literature. However, the real structures are frequently designed as non-uniform structural elements. The main objective of the research is the development of a new proposal for the calculation of the ultimate shear resistance of tapered steel plate girders taking into account the specific behaviour of such members. A new mechanical model is presented in the paper and it is used to show the differences between the behaviour of uniform and tapered web panels subjected to shear. EN 1993-1-5 design specifications for the determination of the shear strength for rectangular plates are improved in order to assess the shear strength of tapered elements. Numerical studies carried out on tapered steel plate girders subjected to shear lead to confirm the suitability of the mechanical model and the proposed design expression.

  17. Determination of the ultimate load in concrete slabs by the yield line finite element method

    International Nuclear Information System (INIS)

    Vaz, L.E.; Feijo, B.; Martha, L.F.R.; Lopes, M.M.

    1984-01-01

    A method for calculating the ultimate load in reinforced concrete slabs is proposed. The method follows the finite element aproach representating the continuum slab as an assembly of rigid triangular plates connected along their sides through yield line elements. This approach leads to the definition of the displacement configuration of the plate only as a function of the transversal displacement at the nodes of the mesh (1 DOF per node) reducing significantly the number of DOF's in relation to the conventional formulation by means of the finite element method (minimum of 3 DOF per node). Nonlinear behaviour of the reinforced concrete section is considered in the definition of the moment rotation curve of the yield lines. The effect of the in plane forces acting in the middle surface of the plate is also taken into account. The validity of the model is verified comparing the numerical solutions with the results of the classical yield line theory. (Author) [pt

  18. Fuzzy stochastic analysis of serviceability and ultimate limit states of two-span pedestrian steel bridge

    Science.gov (United States)

    Kala, Zdeněk; Sandovič, GiedrÄ--

    2012-09-01

    The paper deals with non-linear analysis of ultimate and serviceability limit states of two-span pedestrian steel bridge. The effects of random material and geometrical characteristics on limit states are analyzed. The Monte Carlo method was applied to stochastic analysis. For the serviceability limit state, also influence of fuzzy uncertainty of the limit deflection value on random characteristics of load capacity of variable action was studied. The results prove that, for the type of structure studied, the serviceability limit state is decisive from the point of view of design. The present paper opens a discussion on the use of stochastic analysis to verify the limit deflections given in the standards EUROCODES.

  19. Review of ultimate pressure capacity test of containment structure and scale model design techniques

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jeong Moon; Choi, In Kil [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-03-01

    This study was performed to obtain the basic knowledge of the scaled model test through the review of experimental studies conducted in foreign countries. The results of this study will be used for the wall segment test planed in next year. It was concluded from the previous studies that the larger the model, the greater the trust of the community in the obtained results. It is recommended that a scale model 1/4 - 1/6 be suitable considering the characteristics of concrete, reinforcement, liner and tendon. Such a large scale model test require large amounts of time and budget. Because of these reasons, it is concluded that the containment wall segment test with analytical studies is efficient for the verification of the ultimate pressure capacity of the containment structures. 57 refs., 46 figs., 11 tabs. (Author)

  20. Assessment of Wind Parameter Sensitivity on Ultimate and Fatigue Wind Turbine Loads: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Amy N [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sethuraman, Latha [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jonkman, Jason [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Quick, Julian [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-02-13

    Wind turbines are designed using a set of simulations to ascertain the structural loads that the turbine could encounter. While mean hub-height wind speed is considered to vary, other wind parameters such as turbulence spectra, sheer, veer, spatial coherence, and component correlation are fixed or conditional values that, in reality, could have different characteristics at different sites and have a significant effect on the resulting loads. This paper therefore seeks to assess the sensitivity of different wind parameters on the resulting ultimate and fatigue loads on the turbine during normal operational conditions. Eighteen different wind parameters are screened using an Elementary Effects approach with radial points. As expected, the results show a high sensitivity of the loads to the turbulence standard deviation in the primary wind direction, but the sensitivity to wind shear is often much greater. To a lesser extent, other wind parameters that drive loads include the coherence in the primary wind direction and veer.

  1. Ultimate Pressure Capacity of Prestressed Concrete Containment Vessels with Steel Fibers

    Energy Technology Data Exchange (ETDEWEB)

    Hahm, Dae Gi; Choun, Young Sun; Choi, In Kil [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-10-15

    The ultimate pressure capacity (UPC) of the prestressed concrete containment vessel (PCCV) is very important since the PCCV are final protection to prevent the massive leakage of a radioactive contaminant caused by the severe accident of nuclear power plants (NPPs). The tensile behavior of a concrete is an important factor which influence to the UPC of PCCVs. Hence, nowadays, it is interested that the application of the steel fiber to the PCCVs since that the concrete with steel fiber shows an improved performance in the tensile behavior compared to reinforced concrete (RC). In this study, we performed the UPC analysis of PCCVs with steel fibers corresponding to the different volume ratio of fibers to verify the effectiveness of steel fibers on PCCVs

  2. La simplexité, ultime avatar de la complexité ?

    OpenAIRE

    Demongeot, Jacques; Amor, Hedi Ben; Hazgui, Hana; Lontos, Athanasios

    2014-01-01

    1. Introduction La simplexité peut être considérée comme l’émergence de nouvelles fonctionnalités, issues des interactions entre sous-systèmes (ou modules) d’un système complexe : elle apparaît ainsi comme l’ultime avatar de la complexité, ce qui permet de la définir, sans rupture épistémologique avec le courant scientifique des systèmes complexes, comme la tendance qu’a la nature de sélectionner les fonctions vitales des êtres vivants, en particulier celles les plus utiles à la spécificité e...

  3. Assessing Fatigue and Ultimate Load Uncertainty in Floating Offshore Wind Turbines Due to Varying Simulation Length

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, G.; Lackner, M.; Haid, L.; Matha, D.; Jonkman, J.; Robertson, A.

    2013-07-01

    With the push towards siting wind turbines farther offshore due to higher wind quality and less visibility, floating offshore wind turbines, which can be located in deep water, are becoming an economically attractive option. The International Electrotechnical Commission's (IEC) 61400-3 design standard covers fixed-bottom offshore wind turbines, but there are a number of new research questions that need to be answered to modify these standards so that they are applicable to floating wind turbines. One issue is the appropriate simulation length needed for floating turbines. This paper will discuss the results from a study assessing the impact of simulation length on the ultimate and fatigue loads of the structure, and will address uncertainties associated with changing the simulation length for the analyzed floating platform. Recommendations of required simulation length based on load uncertainty will be made and compared to current simulation length requirements.

  4. Stapledon's Interplanetary Man: A Commonwealth of Worlds and the Ultimate Purpose of Space Colonisation

    Science.gov (United States)

    Crawford, Ian A.

    In his 1948 lecture to the British Interplanetary Society Stapledon considered the ultimate purpose of colonising other worlds. Having examined the possible motivations arising from improved scientific knowledge and access to extraterrestrial raw materials, he concludes that the ultimate benefits of space colonisation will be the increased opportunities for developing human (and post-human) diversity, intellectual and aesthetic potential and, especially, `spirituality'. By the latter concept he meant a striving for ``sensitive and intelligent awareness of things in the universe (including persons), and of the universe as a whole.'' A key insight articulated by Stapledon in this lecture was that this should be the aspiration of all human development anyway, with or without space colonisation, but that the latter would greatly increase the scope for such developments. Another key aspect of his vision was the development of a diverse, but connected, `Commonwealth of Worlds' extending throughout the Solar System, and eventually beyond, within which human potential would be maximised. In this paper I analyse Stapledon's vision of space colonisation, and will conclude that his overall conclusions remain sound. However, I will also argue that he was overly utopian in believing that human social and political unity are prerequisites for space exploration (while agreeing that they are desirable objectives in their own right), and that he unnecessarily downplayed the more prosaic scientific and economic motivations which are likely to be key drivers for space exploration (if not colonisation) in the shorter term. Finally, I draw attention to some recent developments in international space policy which, although probably not influenced by Stapledon's work, are nevertheless congruent with his overarching philosophy as outlined in `Interplanetary Man?'.

  5. Ultimate internal pressure capacity of a reinforced concrete Mark III containment

    International Nuclear Information System (INIS)

    McGaughy, J.P. Jr.; Lin, F.T.; Sen, S.K.

    1983-01-01

    The static ultimate capacity of a Mark III BWR pressure suppression type containment has been investigated with a view to determine its capability to withstand the internal pressure associated with a postulated hydrogen burn. The reinforced concrete containment consists of a right circular cylinder covered by a hemispherical dome and supported on a flat circular foundation mat. A 1/4'' thick welded steel liner plate covers the inside surface of the containment shell. The cylinder is a 3.5 ft. thick shell with an inside radius of 62.0 feet. The thickness of the dome is 3.5 feet. Reinforcement in the shell is comprised of multi-layers of circumferential, meridional and diagonal rebars. Major containment penetrations consists of a circular equipment hatch and two personnel airlock assemblies. The containment ultimate capacity is determined by performing a non-linear analysis using the proprietary finite element computer code 'FINEL'. The code has the capability of modelling concrete cracking in tension and redistribution forces and moments to account for such phenomenon. For analysis purposes, the finite element model included the containment dome and the upper portion of the containment cylinder with appropriate boundary conditions applied at the model cut off region. This portion of the containment structure is selected because the segment of the cylinder that is included in the model has the least amount of hopp reinforcement, and when the general yield state is reached, the hoop reinforcement will be the limiting element. The containment structure has been treated as an axisymmetric shell using axisymmetric quadrilateral finite elements in the radial plane to model the liner plate and concrete. The reinforcing steel have been idealized by finite elements with unidirectional stiffness. (orig./RW)

  6. Ultimate refrigerating conditions, behavior turning and a thermodynamic analysis for absorption–compression hybrid refrigeration cycle

    International Nuclear Information System (INIS)

    Zheng Danxing; Meng Xuelin

    2012-01-01

    Highlights: ► Two novel fundamental concepts of the absorption refrigeration cycle were proposed. ► The interaction mechanism of compressor pressure increasing with other key-parameters was investigated. ► A set of optimal operating condition of hybrid refrigeration cycle was found. ► A simulation and investigation for R134a-DMF hybrid refrigeration cycle was performed. - Abstract: The absorption–compression hybrid refrigeration cycle has been considered as an effective approach to reduce the mechanical work consumption by using low-grade heat, such as solar energy. This work aims at studying the thermodynamic mechanism of the hybrid refrigeration cycle. Two fundamental concepts have been proposed, which are the ultimate refrigerating temperature (or the ultimate temperature lift) and the behavior turning. On the basis of that, the interaction mechanism of compressor pressure increasing with other key-parameters and the impact of compressor pressure increasing on the cycle performance have been investigated. The key-parameters include the concentration difference, the circulation ratio of working fluid, etc. The work points out that the hybrid refrigeration cycle performance varies with the change of compressor outlet pressure and depends on which one achieves dominance in the hybrid refrigeration cycle, the absorption sub-system or the compression sub-system. The behavior turning point during parameters changing corresponds to a maximum value of the heat powered coefficient of performance. In this case, the hybrid refrigeration cycle performance is optimal because the low-grade heat utilization is the most effective. In addition, to validate the theoretical analysis, a solar hybrid refrigeration cycle with R134a–DMF as working pair was simulated. The Peng–Robinson equation of state was adopted to calculate thermophysical properties when the reliability assessment of the prediction models on the available literature data of R134a–DMF system had been

  7. Evaluating strategic environmental assessment in the Netherlands: Content, process and procedure as indissoluble criteria for effectiveness

    NARCIS (Netherlands)

    M.W. van Buuren (Arwin); S.G. Nooteboom (Sibout)

    2009-01-01

    textabstractTo assess the effectiveness of strategic environmental assessment (SEA) we distinguish between its contribution to the quality of the ultimate policy choice (usefulness, applicability), the procedural quality of the planning process (transparency, timeliness) and the quality of

  8. Analysis of a first-order delay differential-delay equation containing two delays

    Science.gov (United States)

    Marriott, C.; Vallée, R.; Delisle, C.

    1989-09-01

    An experimental and numerical analysis of the behavior of a two-delay differential equation is presented. It is shown that much of the system's behavior can be related to the stability behavior of the underlying linearized modes. A new phenomenon, mode crossing, is explored.

  9. A prospective survey of delayed adverse reactions to iohexol in urography and computed tomography

    International Nuclear Information System (INIS)

    Munechika, Hirotsugu; Hiramatsu, Yoshihiro; Kudo, Sho; Sugimura, Kazuro; Hamada, Chikuma; Yamaguchi, Koichi; Katayama, Hitoshi

    2003-01-01

    We investigated 7505 inpatients who underwent intravenous urography or contrast-enhanced computed tomography to assess risk factors for delayed adverse drug reactions to iohexol, a non-ionic iodinated contrast medium. Focusing on delayed adverse reactions, all adverse events were prospectively investigated for 7 days after injection of iohexol. To explore the relevant risk factors, the relationship between occurrence of adverse reactions to iohexol and 17 different variables was evaluated by logistic regression analysis. To assess the influence of seasonal factors, adverse reactions were separately evaluated during two periods: February to April (the pollinosis period in Japan) and July to September (the non-pollinosis period). The prevalence of delayed adverse events and delayed adverse reactions was 3.5 and 2.8%, respectively, whereas the prevalence of adverse events and adverse reactions was 5.7 and 5.0%, respectively. Multivariate analysis showed that six parameters had a significant influence on delayed adverse reactions to iohexol, including (a) a history of allergy, (b) season, (c) radiographic procedure, (d) age, (e) concomitant surgery or other invasive procedures, and (f) concomitant medication. The prevalence of delayed reactions was lower than in previous large-scale studies. Significant risk factors included a history of allergy and performance of radiography during the pollinosis period, suggesting that allergy was involved in delayed adverse reactions. The type of radiographic procedure also had an influence. (orig.)

  10. [To delay may be wise].

    Science.gov (United States)

    Melfa, G; Bernardi, L; Tettamanti, M; Mangano, S

    2004-01-01

    We report a case of acute renal failure, quickly evolved, in which the coexistence of parenchimal nephropaty and renal mass, have induced not a common diagnostic and therapeutic approach, finalized to optimize the interventional nephrology procedures, with the use of various imaging procedures. It is followed a multidisciplinar therapeutic approach, with the employment of dialysis, steroid therapy and surgical treatment.

  11. Is early cord clamping, delayed cord clamping or cord milking best?

    Science.gov (United States)

    Vatansever, Binay; Demirel, Gamze; Ciler Eren, Elif; Erel, Ozcan; Neselioglu, Salim; Karavar, Hande Nur; Gundogdu, Semra; Ulfer, Gozde; Bahadir, Selcen; Tastekin, Ayhan

    2018-04-01

    To compare the antioxidant status of three cord clamping procedures (early clamping, delayed clamping and milking) by analyzing the thiol-disulfide balance. This randomized controlled study enrolled 189 term infants who were divided into three groups according to the cord clamping procedure: early clamping, delayed clamping and milking. Blood samples were collected from the umbilical arteries immediately after clamping, and the thiol/disulfide homeostasis was analyzed. The native and total thiol levels were significantly (p total thiol ratio was significantly (p = .026) lower in the delayed cord clamping and milking groups compared with the early clamping groups. Early cord clamping causes the production of more disulfide bonds and lower thiol levels, indicating that oxidation reactions are increased in the early cord clamping procedure compared with the delayed cord clamping and milking procedures. The oxidant capacity is greater with early cord clamping than with delayed clamping or cord milking. Delayed cord clamping or milking are beneficial in neonatal care, and we suggest that they be performed routinely in all deliveries.

  12. Minimum Delay Moving Object Detection

    KAUST Repository

    Lao, Dong

    2017-11-09

    We present a general framework and method for detection of an object in a video based on apparent motion. The object moves relative to background motion at some unknown time in the video, and the goal is to detect and segment the object as soon it moves in an online manner. Due to unreliability of motion between frames, more than two frames are needed to reliably detect the object. Our method is designed to detect the object(s) with minimum delay, i.e., frames after the object moves, constraining the false alarms. Experiments on a new extensive dataset for moving object detection show that our method achieves less delay for all false alarm constraints than existing state-of-the-art.

  13. Depressive illness delayed Hamlet's revenge.

    Science.gov (United States)

    Shaw, A B; Pickering, Neil

    2002-12-01

    If Hamlet had not delayed his revenge there would have been no play. Many explanations of the delay have been offered in the last four centuries. None is convincing. The interpretation which best fits the evidence best is that Hamlet was suffering from an acute depressive illness, with some obsessional features. He could not make a firm resolve to act. In Shakespeare's time there was no concept of acute depressive illness, although melancholy was well known. Melancholy, however, would have been seen as a character defect. In the tragic model the hero brings himself and others to ruin because of a character defect. Thus, at the time, the play conformed to the tragic model. With today's knowledge, it does not. This analysis adds to, but does not replace, other insights into the play.

  14. Air congestion delay: a review

    Directory of Open Access Journals (Sweden)

    Daniel Alberto Pamplona

    2016-04-01

    Full Text Available This article is a literature review of the air congestion delay and its costs. Air congestion is a worldwide problem. Its existence brings costs for airlines and discomfort for passengers. With the increasing demand for air transport, the study of air congestion has attracted the attention of many researchers around the world. The cause for the delays is erroneously attributed only to the lack of infrastructure investments. The literature review shows that other factors such as population growth, increasing standards of living, lack of operational planning and environmental issues exercise decisive influence. Several studies have been conducted in order to analyze and propose solutions to this problem that affects society as a whole.

  15. Minimum Delay Moving Object Detection

    KAUST Repository

    Lao, Dong

    2017-01-08

    We present a general framework and method for detection of an object in a video based on apparent motion. The object moves relative to background motion at some unknown time in the video, and the goal is to detect and segment the object as soon it moves in an online manner. Due to unreliability of motion between frames, more than two frames are needed to reliably detect the object. Our method is designed to detect the object(s) with minimum delay, i.e., frames after the object moves, constraining the false alarms. Experiments on a new extensive dataset for moving object detection show that our method achieves less delay for all false alarm constraints than existing state-of-the-art.

  16. Minimum Delay Moving Object Detection

    KAUST Repository

    Lao, Dong; Sundaramoorthi, Ganesh

    2017-01-01

    We present a general framework and method for detection of an object in a video based on apparent motion. The object moves relative to background motion at some unknown time in the video, and the goal is to detect and segment the object as soon it moves in an online manner. Due to unreliability of motion between frames, more than two frames are needed to reliably detect the object. Our method is designed to detect the object(s) with minimum delay, i.e., frames after the object moves, constraining the false alarms. Experiments on a new extensive dataset for moving object detection show that our method achieves less delay for all false alarm constraints than existing state-of-the-art.

  17. Investigation of Ultimate Strength of Composite Open-Web Joist-Girders

    OpenAIRE

    Showalter, Sheldon Lee

    1999-01-01

    The goal of this research was to study several methods of generating composite action using open-web joist-girders, designed and manufactured by Nucor Corporation. In addition to comparing the relative performance of these systems, it was intended to determine whether the current accepted design procedure for composite joists could be extended to joist-girders.

  18. Teriparatide Induced Delayed Persistent Hypercalcemia

    Directory of Open Access Journals (Sweden)

    Nirosshan Thiruchelvam

    2014-01-01

    Full Text Available Teriparatide, a recombinant PTH, is an anabolic treatment for osteoporosis that increases bone density. Transient hypercalcemia is a reported side effect of teriparatide that is seen few hours following administration of teriparatide and resolves usually within 16 hours of drug administration. Persistent hypercalcemia, although not observed in clinical trials, is rarely reported. The current case describes a rare complication of teriparatide induced delayed persistent hypercalcemia.

  19. Assembly delay line pulse generators

    CERN Multimedia

    CERN PhotoLab

    1971-01-01

    Assembly of six of the ten delay line pulse generators that will power the ten kicker magnet modules. One modulator part contains two pulse generators. Capacitors, inductances, and voltage dividers are in the oil tank on the left. Triggered high-pressure spark gap switches are on the platforms on the right. High voltage pulse cables to the kicker magnet emerge under the spark gaps. In the centre background are the assembled master gaps.

  20. Emergency evacuation/transportation plan update: Traffic model development and evaluation of early closure procedures. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-10-28

    Prolonged delays in traffic experienced by Laboratory personnel during a recent early dismissal in inclement weather, coupled with reconstruction efforts along NM 502 east of the White Rock Wye for the next 1 to 2 years, has prompted Los Alamos National Laboratory (LANL) to re-evaluate and improve the present transportation plan and its integration with contingency plans maintained in other organizations. Facilities planners and emergency operations staff need to evaluate the transportation system`s capability to inefficiently and safely evacuate LANL under different low-level emergency conditions. A variety of potential procedures governing the release of employees from the different technical areas (TAs) requires evaluation, perhaps with regard to multiple emergency-condition scenarios, with one or more optimal procedures ultimately presented for adoption by Lab Management. The work undertaken in this project will hopefully lay a foundation for an on-going, progressive transportation system analysis capability. It utilizes microscale simulation techniques to affirm, reassess and validate the Laboratory`s Early Dismissal/Closure/Delayed Opening Plan. The Laboratory is required by Federal guidelines, and compelled by prudent practice and conscientious regard for the welfare of employees and nearby residents, to maintain plans and operating procedures for evacuation if the need arises. The tools developed during this process can be used outside of contingency planning. It is anticipated that the traffic models developed will allow site planners to evaluate changes to the traffic network which could better serve the normal traffic levels. Changes in roadway configuration, control strategies (signalization and signing), response strategies to traffic accidents, and patterns of demand can be modelled using the analysis tools developed during this project. Such scenarios typically are important considerations in master planning and facilities programming.

  1. Recreating the scene: an effective way to provide delayed punishment for inappropriate motor behavior.

    OpenAIRE

    Van Houten, R; Rolider, A

    1988-01-01

    A mediated punishment procedure that involved recreating a behavioral sequence by guiding the subject through the behavior in the situation in which it occurred was used to suppress several severe problem behaviors in two developmentally delayed children. The mediational procedure was first used with a 4-year-old autistic boy for biting and then for foot stomping. Next the procedure was used for stealing and hoarding behavior with a multiply handicapped 17-year-old girl. Results indicated tha...

  2. Minimum Delay Moving Object Detection

    KAUST Repository

    Lao, Dong

    2017-05-14

    This thesis presents a general framework and method for detection of an object in a video based on apparent motion. The object moves, at some unknown time, differently than the “background” motion, which can be induced from camera motion. The goal of proposed method is to detect and segment the object as soon it moves in an online manner. Since motion estimation can be unreliable between frames, more than two frames are needed to reliably detect the object. Observing more frames before declaring a detection may lead to a more accurate detection and segmentation, since more motion may be observed leading to a stronger motion cue. However, this leads to greater delay. The proposed method is designed to detect the object(s) with minimum delay, i.e., frames after the object moves, constraining the false alarms, defined as declarations of detection before the object moves or incorrect or inaccurate segmentation at the detection time. Experiments on a new extensive dataset for moving object detection show that our method achieves less delay for all false alarm constraints than existing state-of-the-art.

  3. Development of delayed radiation necrosis

    International Nuclear Information System (INIS)

    Ohara, ShigFeki; Takagi, Terumasa; Shibata, Taichiro; Nagai, Hajime.

    1983-01-01

    The authors discussed the developing process of delayed radiation necrosis of the brain from the case of a 42-year-old female who developed intracranial hypertension and left hemiparesis 5 and a half years after radiotherapy for pituitary adenoma. The initial sign of radiation necrosis was from a CT scan taken 3 and a half years after radiotherapy showing an irregular low density lesion in the right temporal lobe. CT scan 2 years later demonstrated displacement of the midline structures to the left and a larger low density lesion with partially high density in the right MCA territory that was enhanced with intravenous contrast medium. Recovery after a right temporal lobectomy and administration of steroid hormone were uneventful. Eight months later there were no signs of raised intracranial pressure nor of neurological deficits. Tissues obtained from the right temporal lobe at lobectomy revealed the characteristic changes of delayed radiation necrosis; a mixture of fresh, recent, and old vascular lesions in the same specimen. From these findings, it was speculated that delayed radiation necrosis might initially occur within several years after radiotherapy and might gradually take a progressive and extended course, even in cases whose clinical symptoms develop much later. (author)

  4. Treatment of the loss of ultimate heat sink initiating events in the IRSN level 1 PSA

    International Nuclear Information System (INIS)

    Dupuy, Patricia; Georgescu, Gabriel; Corenwinder, Francois

    2014-01-01

    The total loss of the ultimate heat sink is an initiating event which, even it is mainly of external origin, has been considered in the frame of internal events Level 1 PSA by IRSN. The on-going actions on the development of external hazards PSA and the recent incident of loss of the heat sink induced by the ingress of vegetable matter that occurred in France in 2009 have pointed out the need to improve the modeling of the loss of the heat sink initiating event and sequences to better take into account the fact that this loss may be induced by external hazards and thus affect all the site units. The paper presents the historical steps of the modeling of the total loss of the heat sink, the safety stakes of this modeling, the main assumptions used by IRSN in the associated PSA for the 900 MWe reactors and the results obtained. The total loss of the heat sink was not initially addressed in the safety demonstration of French NPPs. On the basis of the insights of the first probabilistic assessments performed in the 80's, the risks associated to this 'multiple failure situation' turned out to be very significant and design and organisational improvements were implemented on the plants. Reviews of the characterization of external hazards and of their consequences on the installations and French operating feedback have revealed that extreme hazards may induce a total loss of the heat sink. Moreover, the accident that occurred at Fukushima in 2011 has pointed out the risk of such a loss of long duration at all site units in case of extreme hazards. In this context, it seems relevant to further improve the modelling of the total loss of the heat sink by considering the external hazards that may cause this loss. In a first step, IRSN has improved the assumptions and data used in the loss of the heat sink PSA model, in particular by considering that such a loss may affect all the site units. The next challenge will be the deeper analysis of the impact of external hazards on

  5. NEOCE: a new external occulting coronagraph experiment for ultimate observations of the chromosphere, corona and interface

    Science.gov (United States)

    Damé, Luc; Fineschi, Silvano; Kuzin, Sergey; Von Fay-Siebenburgen, Erdélyi Robert

    Several ground facilities and space missions are currently dedicated to the study of the Sun at high resolution and of the solar corona in particular. However, and despite significant progress with the advent of space missions and UV, EUV and XUV direct observations of the hot chromosphere and million-degrees coronal plasma, much is yet to be achieved in the understanding of these high temperatures, fine dynamic dissipative structures and of the coronal heating in general. Recent missions have shown the definite role of a wide range of waves and of the magnetic field deep in the inner corona, at the chromosphere-corona interface, where dramatic and physically fundamental changes occur. The dynamics of the chromosphere and corona is controlled and governed by the emerging magnetic field. Accordingly, the direct measurement of the chromospheric and coronal magnetic fields is of prime importance. The solar corona consists of many localised loop-like structures or threads with the plasmas brightening and fading independently. The plasma evolution in each thread is believed to be related to the formation of filaments, each one being dynamic, in a non-equilibrium state. The mechanism sustaining this dynamics, oscillations or waves (Alfvén or other magneto-plasma waves), requires both very high-cadence, multi-spectral observations, and high resolution and coronal magnetometry. This is foreseen in the future Space Mission NEOCE (New External Occulting Coronagraph Experiment), the ultimate new generation high-resolution coronagraphic heliospheric mission, to be proposed for ESA M4. NEOCE, an evolution of the HiRISE mission, is ideally placed at the L5 Lagrangian point (for a better follow-up of CMEs), and provides FUV imaging and spectro-imaging, EUV and XUV imaging and spectroscopy, and ultimate coronagraphy by a remote external occulter (two satellites in formation flying 375 m apart minimizing scattered light) allowing to characterize temperature, densities and

  6. Answering the ultimate question “What is the Proximal Cause of Aging?”

    Science.gov (United States)

    Blagosklonny, Mikhail V.

    2012-01-01

    Recent discoveries suggest that aging is neither driven by accumulation of molecular damage of any cause, nor by random damage of any kind. Some predictions of a new theory, quasi-programmed hyperfunction, have already been confirmed and a clinically-available drug slows aging and delays diseases in animals. The relationship between diseases and aging becomes easily apparent. Yet, the essence of aging turns out to be so startling that the theory cannot be instantly accepted and any possible arguments are raised for its disposal. I discuss that these arguments actually support a new theory. Are any questions remaining? And might accumulation of molecular damage still play a peculiar role in aging? PMID:23425777

  7. Kansas Department of Transportation column expert : ultimate shear capacity of circular columns using the simplified modified compression field theory.

    Science.gov (United States)

    2015-09-01

    The importance of the analysis of circular columns to accurately predict their ultimate confined : capacity under shear-flexure-axial force interaction domain is recognized in light of the extreme load event : imposed by the current American Associat...

  8. Classification of radioactive waste and determination of waste specifications as well as conditions of acceptance for ultimate storage

    International Nuclear Information System (INIS)

    Merz, E.

    1983-04-01

    The determination of waste specification and conditions of acceptance must follow a certain scheme, the basics of which will be presented. First the types of waste and the ultimate storage facilities will be characterized. The various categories of waste will be listed in a universally valid system, and the preliminary conditioning options will be determined. Based on the results of safety analysis taking into account the whole system - geological circumstances, ultimate store mines, types and forms of waste - specifications for the various ultimate store products are to be derived following iterative methods. Suggestions though not of a binding nature and probably subject to eventual revisions in part will be presented. To ensure the safety goals, i.e. the exclusion of radioactivity from the human biosphere, appropriate quality control is required concerning the production and the acceptance at the ultimate store. The guiding principles to be heeded will be discussed in brief. (orig./HP) [de

  9. The effects of physical activity on impulsive choice: Influence of sensitivity to reinforcement amount and delay.

    Science.gov (United States)

    Strickland, Justin C; Feinstein, Max A; Lacy, Ryan T; Smith, Mark A

    2016-05-01

    Impulsive choice is a diagnostic feature and/or complicating factor for several psychological disorders and may be examined in the laboratory using delay-discounting procedures. Recent investigators have proposed using quantitative measures of analysis to examine the behavioral processes contributing to impulsive choice. The purpose of this study was to examine the effects of physical activity (i.e., wheel running) on impulsive choice in a single-response, discrete-trial procedure using two quantitative methods of analysis. To this end, rats were assigned to physical activity or sedentary groups and trained to respond in a delay-discounting procedure. In this procedure, one lever always produced one food pellet immediately, whereas a second lever produced three food pellets after a 0, 10, 20, 40, or 80-s delay. Estimates of sensitivity to reinforcement amount and sensitivity to reinforcement delay were determined using (1) a simple linear analysis and (2) an analysis of logarithmically transformed response ratios. Both analyses revealed that physical activity decreased sensitivity to reinforcement amount and sensitivity to reinforcement delay. These findings indicate that (1) physical activity has significant but functionally opposing effects on the behavioral processes that contribute to impulsive choice and (2) both quantitative methods of analysis are appropriate for use in single-response, discrete-trial procedures. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Tests and Procedures

    Science.gov (United States)

    ... Something Good Come From This? Overview Exploring the Idea of Personal Growth Helping My Child Find Personal ... Unite! Ultimate Hike CureSearch Gold CureSearch Challenge Back Business Partnerships Launch a Corporate Partnership Our Partners Connect ...

  11. Anxiety Around Medical Procedures

    Science.gov (United States)

    ... Something Good Come From This? Overview Exploring the Idea of Personal Growth Helping My Child Find Personal ... Unite! Ultimate Hike CureSearch Gold CureSearch Challenge Back Business Partnerships Launch a Corporate Partnership Our Partners Connect ...

  12. A probabilistics safety assessment of ultimate response guidelines of Maanshan Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Wang, P-Y.; Lee, M. [National Tsing Hua Univ., Hsinchu, Taiwan (China); Chao, C-C. [Inst. of Nuclear Energy Research, Taoyuan, Taiwan (China)

    2014-07-01

    Ultimate Response Guidelines (URGs) was proposed to mitigate the so called 'Fukushima type accident' of nuclear power plants (NPPs). As specified in URGs, if it is necessary, operators will depressurize the secondary side of steam generators (SGs) to bring in the low pressure water. The injection damages the economic value of the plant. However, the injection prevents the cladding temperature from rising above 1500 F (1089 K), which is the temperature that release of volatile fission products from gap is initiated. In the present study, the impact of URGs on the Core Damage Frequency (CDF) in a SBO (Station Blackout) accident of a Pressurized Water Reactor (PWR) designed by Westinghouse and adopts large dry containment is quantified. In the Base Case analysis of the study, the actions in the URGs are not considered. The CDF of SBO in the base case calculation is 2.49x10{sup -7} year. The actions specified in URGs can reduce CDF by 62%. The strategies in URGs are very effective in enhancing the reliability of decay heat removal via SG secondary side. Therefore, the implementation of these strategies can reduce the CDF of sequences involving late failure of AFWS. After the incorporation URGs, the dominant sequences of SBO are the sequences with seal failure. (author)

  13. Ultimate pressure capacity assessment of R FRC PCCV based on the tension stiffening tests

    International Nuclear Information System (INIS)

    Hahm, Dae Gi; Choun, Young Sun

    2012-01-01

    The use of fibers in concrete or cement composites can enhance the performance of structural elements. Fibers have been used for a cement mixture to increase the toughness and tensile strength, and to improve the cracking and deformation characteristics. The addition of fibers into concrete can improve the ductility and increase the tensile resistance of concrete structures. Recently, the application of fibers to prestressed concrete containment vessels (PCCVs) has been a major research topic. However, the tensile stiffening behavior of reinforced - fiber reinforced concrete (RFRC) is not fully developed yet especially for specimens using large diameter re bars. In nuclear power plant (NPP) PCCVs, large diameter re bars are applied. Therefore, the tensile stiffening behavior model should be developed to assess ultimate pressure capacity (UPC) of R FRC PCCVs. In this study, we modeled the tensile stiffening behavior of R FRC PCCVs by using recently developed model, and assessed the UPC of R FRC PCCVs. To do this, we performed tension stiffening test of R FRC with large diameter re bar

  14. An Experimental Investigation on the Ultimate Strength of Partially Infilled: Braced Steel Frames

    Science.gov (United States)

    Dubey, Shailendra Kumar Damodar; Kute, Sunil Y.

    2017-12-01

    Infilled walls are usually, considered as non-structural elements. However, these walls are effective in carrying lateral loads. In this regard, an experimental investigation was planned and conducted to study the effect of braced and partially infilled steel frames with cement mortar and concrete in comparison to the bare frames. All these frames were tested up to collapse and subjected only to horizontal loads to obtain an effective and possible solution for soft storey which are generally not infilled. In comparison to bare steel frames, partially infilled frames have an increase of lateral load capacity by 45-60%. Central bracing is more effective than that of the corner bracing. For the same load partially infilled frames have significantly less deflection than that of the bare frames. A reduced load factor is suggested for the design of soft storey columns with the partial infills. A mathematical model has been proposed to calculate the theoretical ultimate load for the braced, cement mortar and concrete partial infilled frames.

  15. Hierarchical nanoporous metals as a path toward the ultimate three-dimensional functionality.

    Science.gov (United States)

    Fujita, Takeshi

    2017-01-01

    Nanoporous metals prepared via dealloying or selective leaching of solid solution alloys and compounds represent an emerging class of materials. They possess a three-dimensional (3D) structure of randomly interpenetrating ligaments/nanopores with sizes between 5 nm and several tens of micrometers, which can be tuned by varying their preparation conditions (such as dealloying time and temperature) or additional thermal coarsening. As compared to other nanostructured materials, nanoporous metals have many advantages, including their bicontinuous structure, tunable pore sizes, bulk form, good electrical conductivity, and high structural stability. Therefore, nanoporous metals represent ideal 3D materials with versatile functionality, which can be utilized in various fields. In this review, we describe the recent applications of nanoporous metals in molecular detection, catalysis, 3D graphene synthesis, hierarchical pore formation, and additive manufacturing (3D printing) together with our own achievements in these areas. Finally, we discuss possible ways of realizing the ultimate 3D functionality beyond the scope of nanoporous metals.

  16. COLLECTIVE VORTEX BEHAVIORS: DIVERSITY, PROXIMATE, AND ULTIMATE CAUSES OF CIRCULAR ANIMAL GROUP MOVEMENTS.

    Science.gov (United States)

    Delcourt, Johann; Bode, Nikolai W F; Denoël, Mathieu

    2016-03-01

    Ant mill, caterpillar circle, bat doughnut, amphibian vortex, duck swirl, and fish torus are different names for rotating circular animal formations, where individuals turn around a common center. These "collective vortex behaviors" occur at different group sizes from pairs to several million individuals and have been reported in a large number of organisms, from bacteria to vertebrates, including humans. However, to date, no comprehensive review and synthesis of the literature on vortex behaviors has been conducted. Here, we review the state of the art of the proximate and ultimate causes of vortex behaviors. The ubiquity of this behavioral phenomenon could suggest common causes or fundamental underlying principles across contexts. However, we find that a variety of proximate mechanisms give rise to vortex behaviors. We highlight the potential benefits of collective vortex behaviors to individuals involved in them. For example, in some species, vortices increase feeding efficiency and could give protection against predators. It has also been argued that vortices could improve collective decision-making and information transfer. We highlight gaps in our understanding of these ubiquitous behavioral phenomena and discuss future directions for research in vortex studies.

  17. Ultimate intra-wafer critical dimension uniformity control by using lithography and etch tool corrections

    Science.gov (United States)

    Kubis, Michael; Wise, Rich; Reijnen, Liesbeth; Viatkina, Katja; Jaenen, Patrick; Luca, Melisa; Mernier, Guillaume; Chahine, Charlotte; Hellin, David; Kam, Benjamin; Sobieski, Daniel; Vertommen, Johan; Mulkens, Jan; Dusa, Mircea; Dixit, Girish; Shamma, Nader; Leray, Philippe

    2016-03-01

    With shrinking design rules, the overall patterning requirements are getting aggressively tighter. For the 7-nm node and below, allowable CD uniformity variations are entering the Angstrom region (ref [1]). Optimizing inter- and intra-field CD uniformity of the final pattern requires a holistic tuning of all process steps. In previous work, CD control with either litho cluster or etch tool corrections has been discussed. Today, we present a holistic CD control approach, combining the correction capability of the etch tool with the correction capability of the exposure tool. The study is done on 10-nm logic node wafers, processed with a test vehicle stack patterning sequence. We include wafer-to-wafer and lot-to-lot variation and apply optical scatterometry to characterize the fingerprints. Making use of all available correction capabilities (lithography and etch), we investigated single application of exposure tool corrections and of etch tool corrections as well as combinations of both to reach the lowest CD uniformity. Results of the final pattern uniformity based on single and combined corrections are shown. We conclude on the application of this holistic lithography and etch optimization to 7nm High-Volume manufacturing, paving the way to ultimate within-wafer CD uniformity control.

  18. PEP-X: An Ultimate Storage Ring Based on Fourth-Order Geometric Achromats

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yunhai; Bane, Karl; Hettel, Robert; Nosochkov, Yuri; Wang, Min-Huey; /SLAC

    2012-04-06

    We have designed an 'ultimate' storage ring for the PEP-X light source that achieves the diffraction limited emittances (at 1.5 {angstrom}) of 12 pm-rad in both horizontal and vertical planes with a 4.5-GeV beam. These emittances include the contribution of intrabeam scattering at a nominal current of 200 mA in 3300 bunches. This quality beam in conjunction with a conventional 4-m undulator in a straight section can generate synchrotron radiation having a spectral brightness above 10{sup 22} [photons/s/mm{sup 2}/mrad{sup 2}/0.1% BW] at a 10 keV photon energy. The high coherence at the diffraction limit makes PEP-X competitive with 4th generation light sources based on an energy recovery linac. In addition, the beam lifetime is several hours and the dynamic aperture is large enough to allow off-axis injection. The alignment and stability tolerances, though challenging, are achievable. A ring with all these properties is only possible because of several major advances in mitigating the effects of nonlinear resonances.

  19. A new approach to the modeling of ultimate heat sink cooling ponds

    International Nuclear Information System (INIS)

    Policastro, A.J.; Wastag, M.; Paul, J.; Carhart, R.A.

    1996-01-01

    Ultimate heat sink (UHS) cooling pond thermal performance is analyzed by a new method in which zero, one, and three-dimensional models are used in combination. A typical UHS pond has an irregular shape covering 20 hectares at an average depth of 4 m with a heavy thermal load of 40 MWt (megawatts thermal) per hectare. The resulting flow field can be one, two or three dimensional. A three-dimensional numerical model (Paul 1983) is modified and used to determine the effective dimensionality of the pond under accident conditions. The model's surface heat transfer formulas and its predictions of thermal hydraulics are verified using laboratory and field data. The Paul model shows that, unlike normal cooling ponds, a typical UHS pond is vertically-mixed with only a longitudinal temperature variation. Buoyancy-driven circulations, strong discharge-to-intake flow, and rapid surface heat removal break down the usual vertical stratification. Predictions of the one-dimensional MITEMP model are shown to agree with Paul model predictions for a typical UHS pond at the Catawba Nuclear Power Plant

  20. Test research and analysis for ultimate capacity of Qinshan NPP PCCV

    International Nuclear Information System (INIS)

    Zufeng, X.

    1994-01-01

    This paper introduces design and research for containment of Qinshan NPP which is the first PWR in CHINA designed and constructed by ourselves. The PCCV design is basically in conformity to ASME code. To verify the structural integrity capacity of Qinshan NPP containment, we fulfilled SIT and ILRT successfully in June, 1991. The special attention of the paper is focused on the ultimate capacity of the PCCV under severe accidents and earthquake. A study comprised of five different independent parts has been performed for the development of containment model test and corresponding nonlinear analysis. There are two prestressed concrete containment models with equipment hatch. One is 1/15 scale with steel liner tested on shake table and then moved out loaded with atmospheric pressure. The other is 1/10 scale without steel liner loaded with water pressure until destruction. From different methods including model test and nonlinear analysis, all obtained unanimous conclusion. The capacity under internal pressure and earthquake is reliable. The safety margin is enough. Consequently, in the second phase of Qinshan NPP and other PWR NPP under design, PCCV should be a better selection in China since it's more economic, rational and safe. (author)

  1. Ultimate disposition of aluminum clad spent nuclear fuel in the United States

    International Nuclear Information System (INIS)

    Messick, C.E.; Clark, W.D.; Clapper, M.; Mustin, T.P.

    2001-01-01

    Treatment and disposition of spent nuclear fuel (SNF) in the United States has changed significantly over the last decade due to change in world climate associated with nuclear material. Chemical processing of aluminum based SNF is ending and alternate disposition paths are being developed that will allow for the ultimate disposition of the enriched uranium in this SNF. Existing inventories of aluminum based SNF are currently being stored primarily in water-filled basins at the Savannah River Site (SRS) while these alternate disposition paths are being developed and implemented. Nuclear nonproliferation continues to be a worldwide concern and it is causing a significant influence on the development of management alternatives for SNF. SRS recently completed an environmental impact statement for the management of aluminum clad SNF that selects alternatives for all of the fuels in inventory. The U.S. Department of Energy and SRS are now implementing a dual strategy of processing small quantities of 'problematic' SNF while developing an alternative technology to dispose of the remaining aluminum clad SNF in the proposed monitored geologic repository. (author)

  2. Structural Phenomenon of Cement-Based Composite Elements in Ultimate Limit State

    Directory of Open Access Journals (Sweden)

    I. Iskhakov

    2016-01-01

    Full Text Available Cement-based composite materials have minimum of two components, one of which has higher strength compared to the other. Such materials include concrete, reinforced concrete (RC, and ferrocement, applied in single- or two-layer RC elements. This paper discusses experimental and theoretical results, obtained by the authors in the recent three decades. The authors have payed attention to a structural phenomenon that many design features (parameters, properties, etc. at ultimate limit state (ULS of a structure are twice higher (or lower than at initial loading state. This phenomenon is evident at material properties, structures (or their elements, and static and/or dynamic structural response. The phenomenon is based on two ideas that were developed by first author: quasi-isotropic state of a structure at ULS and minimax principle. This phenomenon is supported by experimental and theoretical results, obtained for various structures, like beams, frames, spatial structures, and structural joints under static or/and dynamic loadings. This study provides valuable indicators for experiments’ planning and estimation of structural state. The phenomenon provides additional equation(s for calculating parameters that are usually obtained experimentally and can lead to developing design concepts and RC theory, in which the number of empirical design coefficients will be minimal.

  3. Thermal performance experiments on ultimate heat sinks, spray ponds, and cooling ponds

    International Nuclear Information System (INIS)

    Hadlock, R.K.

    1976-12-01

    A program of measurement on a Battelle-Northwest (BNW) spray pond has been completed to prove an integrated instrumentation system for application in future field experiments. The measurement programs in the field will produce data of relevance to the design and understanding of performance for ultimate heat sinks as components of emergency core cooling systems. In the absence of active emergency cooling systems, the data will be obtained on analog systems--prime candidates among these are the naturally-occurring hot ponds at Yellowstone National Park and man-made hot cooling ponds at Savannah River National Laboratory as well as spray ponds at various industrial facilities. The proof experiment has provided data that not only illustrate the effectiveness of the instrumentation system but also display interesting site-specific heat transfer processes. The data to be obtained in the field will also be site specific but must be of generic applicability in modeling for design and performance purposes. The integrated instrumentation system will evolve, through modest modifications and substantial supplementation, to provide the requisite data for the more demanding situation of work in and about hot water

  4. Genotyping by sequencing (GBS, an ultimate marker-assisted selection (MAS tool to accelerate plant breeding

    Directory of Open Access Journals (Sweden)

    Jiangfeng eHe

    2014-09-01

    Full Text Available Marker-assisted selection (MAS refers to the use of molecular markers to assist phenotypic selections in crop improvement. Several types of molecular markers, such as single nucleotide polymorphism (SNP, have been identified and effectively used in plant breeding. The application of next-generation sequencing (NGS technologies has led to remarkable advances in whole genome sequencing, which provides ultra-throughput sequences to revolutionize plant genotyping and breeding. To further broaden NGS usages to large crop genomes such as maize and wheat, genotyping by sequencing (GBS has been developed and applied in sequencing multiplexed samples that combine molecular marker discovery and genotyping. GBS is a novel application of NGS protocols for discovering and genotyping SNPs in crop genomes and populations. The GBS approach includes the digestion of genomic DNA with restriction enzymes followed by the ligation of barcode adapter, PCR amplification and sequencing of the amplified DNA pool on a single lane of flow cells. Bioinformatic pipelines are needed to analyze and interpret GBS datasets. As an ultimate MAS tool and a cost-effective technique, GBS has been successfully used in implementing genome-wide association study (GWAS, genomic diversity study, genetic linkage analysis, molecular marker discovery and genomic selection (GS under a large scale of plant breeding programs.

  5. Ultimate pressure capacity assessment of R FRC PCCV based on the tension stiffening tests

    Energy Technology Data Exchange (ETDEWEB)

    Hahm, Dae Gi; Choun, Young Sun [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    The use of fibers in concrete or cement composites can enhance the performance of structural elements. Fibers have been used for a cement mixture to increase the toughness and tensile strength, and to improve the cracking and deformation characteristics. The addition of fibers into concrete can improve the ductility and increase the tensile resistance of concrete structures. Recently, the application of fibers to prestressed concrete containment vessels (PCCVs) has been a major research topic. However, the tensile stiffening behavior of reinforced - fiber reinforced concrete (RFRC) is not fully developed yet especially for specimens using large diameter re bars. In nuclear power plant (NPP) PCCVs, large diameter re bars are applied. Therefore, the tensile stiffening behavior model should be developed to assess ultimate pressure capacity (UPC) of R FRC PCCVs. In this study, we modeled the tensile stiffening behavior of R FRC PCCVs by using recently developed model, and assessed the UPC of R FRC PCCVs. To do this, we performed tension stiffening test of R FRC with large diameter re bar.

  6. The CRISPR-Cas9 technology: Closer to the ultimate toolkit for targeted genome editing.

    Science.gov (United States)

    Quétier, Francis

    2016-01-01

    The first period of plant genome editing was based on Agrobacterium; chemical mutagenesis by EMS (ethyl methanesulfonate) and ionizing radiations; each of these technologies led to randomly distributed genome modifications. The second period is associated with the discoveries of homing and meganuclease enzymes during the 80s and 90s, which were then engineered to provide efficient tools for targeted editing. From 2006 to 2012, a few crop plants were successfully and precisely modified using zinc-finger nucleases. A third wave of improvement in genome editing, which led to a dramatic decrease in off-target events, was achieved in 2009-2011 with the TALEN technology. The latest revolution surfaced in 2013 with the CRISPR-Cas9 system, whose high efficiency and technical ease of use is really impressive; scientists can use in-house kits or commercially available kits; the only two requirements are to carefully choose the location of the DNA double strand breaks to be induced and then to order an oligonucleotide. While this close-to- ultimate toolkit for targeted editing of genomes represents dramatic scientific progress which allows the development of more complex useful agronomic traits through synthetic biology, the social acceptance of genome editing remains regularly questioned by anti-GMO citizens and organizations. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  7. Design Dependent Cutoff Frequency of Nanotransistors Near the Ultimate Performance Limit

    Science.gov (United States)

    Kordrostami, Zoheir; Sheikhi, M. Hossein; Zarifkar, Abbas

    2012-12-01

    We have studied the effect of different structural designs of double gate MOSFETs (DG-MOSFETs) and carbon nanotube field effect transistors (CNTFETs) on the cutoff frequency (fT). The effects of metallic contacts with Schottky barriers, gate work function, dual material gate (DMG), halo doped channel and lightly doped drain and source (LDDS) architectures on the fT have been investigated for DG-MOSFETs and CNTFETs and the design dependent fT for both types of transistors has been studied for the first time. The simulations are based on the Schrödinger-Poisson solvers developed for each nanotransistor separately. The ballistic limit has been studied as the ultimate performance limit of the DG-MOSFETs and CNTFETs. The results of this paper, for the first time, show how some designations used for modification of short channel effects or current-voltage characteristics affect the fT. The results revealed that the cutoff frequencies of both types of the transistors exhibit the same behavior with changing design parameters. We have shown that the Schottky barriers, parasitic capacitances and halo doping reduce the fT and have proposed the DMG and LDDS artchitectures as ways to increase the fT for DG-MOSFETs and CNTFETs for the first time.

  8. Pareto-Optimal Evaluation of Ultimate Limit States in Offshore Wind Turbine Structural Analysis

    Directory of Open Access Journals (Sweden)

    Michael Muskulus

    2015-12-01

    Full Text Available The ultimate capacity of support structures is checked with extreme loads. This is straightforward when the limit state equations depend on a single load component, and it has become common to report maxima for each load component. However, if more than one load component is influential, e.g., both axial force and bending moments, it is not straightforward how to define an extreme load. The combination of univariate maxima can be too conservative, and many different combinations of load components can result in the worst value of the limit state equations. The use of contemporaneous load vectors is typically non-conservative. Therefore, in practice, limit state checks are done for each possible load vector, from each time step of a simulation. This is not feasible when performing reliability assessments and structural optimization, where additional, time-consuming computations are involved for each load vector. We therefore propose to use Pareto-optimal loads, which are a small set of loads that together represent all possible worst case scenarios. Simulations with two reference wind turbines show that this approach can be very useful for jacket structures, whereas the design of monopiles is often governed by the bending moment only. Even in this case, the approach might be useful when approaching the structural limits during optimization.

  9. Value measurement of nuclear medicine procedures

    International Nuclear Information System (INIS)

    Potchen, E.J.; Harris, G.I.; Schonbein, W.R.; Rashford, N.J.

    1977-01-01

    The difficulty in measuring the benefit component for cost/benefit analysis of diagnostic procedures in medicine is portrayed as a complex issue relating the objective of intent to a classification of types of decisions a physician must make in evaluating a patient's problem. Ultimately, it seems desirable to develop measuring instruments such as attitude measurement tools by which the relative value of alternative diagnostic procedures could be measured in terms of what they contribute to diminishing the patient's personal perception of disease. Even without this idealized objective, it is reasonable to assume that diagnostic tests which do not contain information, defined as a change in the randomness of a state of knowledge, could not be expected to ultimately benefit the patient. Thus diagnostic information should provide a rational direction for the physician to modify the course of the patient's illness. Since information can be measured as a change in randomness of a knowledge state, we can determine the information content of a specific nuclear medicine procedure when faced with an array of diagnostic problems. These measurements remain to be made for clinical nuclear medicine procedures and are currently under study

  10. Synchronization in networks with heterogeneous coupling delays

    Science.gov (United States)

    Otto, Andreas; Radons, Günter; Bachrathy, Dániel; Orosz, Gábor

    2018-01-01

    Synchronization in networks of identical oscillators with heterogeneous coupling delays is studied. A decomposition of the network dynamics is obtained by block diagonalizing a newly introduced adjacency lag operator which contains the topology of the network as well as the corresponding coupling delays. This generalizes the master stability function approach, which was developed for homogenous delays. As a result the network dynamics can be analyzed by delay differential equations with distributed delay, where different delay distributions emerge for different network modes. Frequency domain methods are used for the stability analysis of synchronized equilibria and synchronized periodic orbits. As an example, the synchronization behavior in a system of delay-coupled Hodgkin-Huxley neurons is investigated. It is shown that the parameter regions where synchronized periodic spiking is unstable expand when increasing the delay heterogeneity.

  11. Asymptotic Behaviour and Extinction of Delay Lotka-Volterra Model with Jump-Diffusion

    Directory of Open Access Journals (Sweden)

    Dan Li

    2014-01-01

    Full Text Available This paper studies the effect of jump-diffusion random environmental perturbations on the asymptotic behaviour and extinction of Lotka-Volterra population dynamics with delays. The contributions of this paper lie in the following: (a to consider delay stochastic differential equation with jumps, we introduce a proper initial data space, in which the initial data may be discontinuous function with downward jumps; (b we show that the delay stochastic differential equation with jumps associated with our model has a unique global positive solution and give sufficient conditions that ensure stochastically ultimate boundedness, moment average boundedness in time, and asymptotic polynomial growth of our model; (c the sufficient conditions for the extinction of the system are obtained, which generalized the former results and showed that the sufficiently large random jump magnitudes and intensity (average rate of jump events arrival may lead to extinction of the population.

  12. OPPORTUNITY COSTS OF REWARD DELAYS AND THE DISCOUNTING OF HYPOTHETICAL MONEY AND CIGARETTES

    Science.gov (United States)

    Johnson, Patrick S.; Herrmann, Evan S.; Johnson, Matthew W.

    2015-01-01

    Humans are reported to discount delayed rewards at lower rates than nonhumans. However, nonhumans are studied in tasks that restrict reinforcement during delays, whereas humans are typically studied in tasks that do not restrict reinforcement during delays. In nonhuman tasks, the opportunity cost of restricted reinforcement during delays may increase delay discounting rates. The present within-subjects study used online crowdsourcing (Amazon Mechanical Turk, or MTurk) to assess the discounting of hypothetical delayed money (and cigarettes in smokers) under four hypothetical framing conditions differing in the availability of reinforcement during delays. At one extreme, participants were free to leave their computer without returning, and engage in any behavior during reward delays (modeling typical human tasks). At the opposite extreme, participants were required to stay at their computer and engage in little other behavior during reward delays (modeling typical nonhuman tasks). Discounting rates increased as an orderly function of opportunity cost. Results also indicated predominantly hyperbolic discounting, the “magnitude effect,” steeper discounting of cigarettes than money, and positive correlations between discounting rates of these commodities. This is the first study to test the effects of opportunity costs on discounting, and suggests that procedural differences may partially account for observed species differences in discounting. PMID:25388973

  13. Synchronization analysis of coloured delayed networks under ...

    Indian Academy of Sciences (India)

    This paper investigates synchronization of coloured delayed networks under decentralized pinning intermittent control. To begin with, the time delays are taken into account in the coloured networks. In addition, we propose a decentralized pinning intermittent control for coloured delayed networks, which is different from that ...

  14. Delayed neutrons as a probe of nuclear charge distribution in fission of heavy nuclei by neutrons

    CERN Document Server

    Isaev, S G; Piksaikin, V M; Roshchenko, V A

    2001-01-01

    A method of the determination of cumulative yields of delayed neutron precursors is developed. This method is based on the iterative least-square procedure applied to delayed neutron decay curves measured after irradiation of sup 2 sup 3 sup 5 U sample by thermal neutrons. Obtained cumulative yields in turns were used for deriving the values of the most probable charge in low-energy fission of the above-mentioned nucleus.

  15. Delayed neutrons as a probe of nuclear charge distribution in fission of heavy nuclei by neutrons

    International Nuclear Information System (INIS)

    Isaev, S.G.; Piksaikin, V.M.; Kazakov, L.E.; Roshchenko, V.A.

    2002-01-01

    A method of the determination of cumulative yields of delayed neutron precursors is developed. This method is based on the iterative least-square procedure applied to delayed neutron decay curves measured after irradiation of 235 U sample by thermal neutrons. Obtained cumulative yields in turns were used for deriving the values of the most probable charge in low-energy fission of the above-mentioned nucleus. (author)

  16. Cracking chaos-based encryption systems ruled by nonlinear time delay differential equations

    International Nuclear Information System (INIS)

    Udaltsov, Vladimir S.; Goedgebuer, Jean-Pierre; Larger, Laurent; Cuenot, Jean-Baptiste; Levy, Pascal; Rhodes, William T.

    2003-01-01

    We report that signal encoding with high-dimensional chaos produced by delayed feedback systems with a strong nonlinearity can be broken. We describe the procedure and illustrate the method with chaotic waveforms obtained from a strongly nonlinear optical system that we used previously to demonstrate signal encryption/decryption with chaos in wavelength. The method can be extended to any systems ruled by nonlinear time-delayed differential equations

  17. Two weeks delayed bleeding in blunt liver injury: case report and review of the literature

    Directory of Open Access Journals (Sweden)

    Chulsky Alexander

    2011-04-01

    Full Text Available Abstract Most cases of blunt hepatic trauma are treated nowadays non-operatively. This type of conservative treatment has resulted in increased complication rate. Delayed complications occur in cases that didn't require surgical intervention during the first 24 hours. The most common late complication is hemorrhage. We report a case of two weeks delayed hemorrhage after blunt hepatic trauma in an adult. We describe the diagnostic procedures, the surgical treatment and review the relevant literature.

  18. Factors associated with delayed bleeding after resection of large nonpedunculated colorectal polyps.

    Science.gov (United States)

    Elliott, Timothy R; Tsiamoulos, Zacharias P; Thomas-Gibson, Siwan; Suzuki, Noriko; Bourikas, Leonidas A; Hart, Ailsa; Bassett, Paul; Saunders, Brian P

    2018-04-06

    Delayed bleeding is the most common significant complication after piecemeal endoscopic mucosal resection (p-EMR) of large nonpedunculated colorectal polyps (NPCPs). Risk factors for delayed bleeding are incompletely defined. We aimed to determine risk factors for delayed bleeding following p-EMR.  Data were analyzed from a prospective tertiary center audit of patients with NPCPs ≥ 20 mm who underwent p-EMR between 2010 and 2012. Patient, polyp, and procedure-related data were collected. Four post p-EMR defect factors were evaluated for interobserver agreement and included in analysis. Delayed bleeding severity was reported in accordance with guidelines. Predictors of bleeding were identified.  Delayed bleeding requiring hospitalization occurred after 22 of 330 procedures (6.7 %). A total of 11 patients required blood transfusion; of these, 4 underwent urgent colonoscopy, 1 underwent radiological embolization, and 1 required surgery. Interobserver agreement for identification of the four post p-EMR defect factors was moderate (kappa range 0.52 - 0.57). Factors associated with delayed bleeding were visible muscle fibers ( P  = 0.03) and the presence of a "cherry red spot" ( P  = 0.05) in the post p-EMR defect. Factors not associated with delayed bleeding were American Association of Anesthesiologists class, aspirin use, polyp size, site, and use of argon plasma coagulation.  Visible muscle fibers and the presence of a "cherry red spot" in the resection defect were associated with delayed bleeding after p-EMR. These findings suggest evaluation and photodocumentation of the post p-EMR defect is important and, when considered alongside other patient and procedural factors, may help to reduce the incidence and severity of delayed bleeding. © Georg Thieme Verlag KG Stuttgart · New York.

  19. The U.S. Gas Flooding Experience: CO2 Injection Strategies and Impact on Ultimate Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Nunez-Lopez, Vanessa [The University of Texas at Austin; Hosseini, Seyyed; Gil-Egui, Ramon

    2017-09-29

    The Permian Basin in West Texas and southwestern New Mexico has seen 45 years of oil reserve growth through CO2 enhanced oil recovery (CO2 EOR). More than 60 CO2 EOR projects are currently active in the region’s limestone, sandstone and dolomite reservoirs. Water alternating gas (WAG) has been the development strategy of choice in the Permian for several technical and economic reasons. More recently, the technology started to get implemented in the much more porous and permeable clastic depositional systems of the onshore U.S. Gulf Coast. Continued CO2 injection (CGI), as opposed to WAG, was selected as the injection strategy to develop Gulf Coast oil fields, where CO2 injection volumes are significantly larger (up to 6 times larger) than those of the Permian. We conducted a compositional simulation based study with the objective of comparing the CO2 utilization ratios (volume of CO2 injected to produce a barrel of oil) of 4 conventional and novel CO2 injection strategies: (1) continuous gas injection (CGI), (2) water alternating gas (WAG), (3) water curtain injection (WCI), and (4) WAG and WCI combination. These injection scenarios were simulated using the GEM module from the Computer Modeling Group (CMG). GEM is an advanced general equation-of-state compositional simulator, which includes equation of state, CO2 miscible flood, CO2/brine interactions, and complex phase behavior. The simulator is set up to model three fluid phases including water, oil, and gas. Our study demonstrates how the selected field development strategy has a significant impact on the ultimate recovery of CO2-EOR projects, with GCI injection providing maximum oil recovery in absolute volume terms, but with WAG offering a more balanced technical-economical approach.

  20. Squat Biomechanical Modeling Results from Exercising on the Hybrid Ultimate Lifting Kit

    Science.gov (United States)

    Gallo, Christopher A.; Thompson, William K.; Lewandowski, Beth E.; Jagodnik, Kathleen M.

    2016-01-01

    Long duration space travel will expose astronauts to extended periods of reduced gravity. Since gravity is not present to aid loading, astronauts will use resistive and aerobic exercise regimes for the duration of the space flight to minimize loss of bone density, muscle mass and aerobic capacity that occurs during exposure to a reduced gravity environment. Unlike the International Space Station (ISS), the area available for an exercise device in the next generation of spacecraft is limited and therefore compact resistance exercise device prototypes are being developed. The Advanced Resistive Exercise Device (ARED) currently on the ISS is being used as a benchmark for the functional performance of these new devices. Biomechanical data collection and computational modeling aid the device design process by quantifying the joint torques and the musculoskeletal forces that occur during exercises performed on the prototype devices. The computational models currently under development utilize the OpenSim software, an open source code for musculoskeletal modeling, with biomechanical input data from test subjects for estimation of muscle and joint loads. The subjects are instrumented with reflective markers for motion capture data collection while exercising on the Hybrid Ultimate Lifting Kit (HULK) prototype device. Ground reaction force data is collected with force plates under the feet and device loading is recorded through load cells internal to the HULK. Test variables include applied device load, narrow or wide foot stance, slow or fast cadence and the harness or long bar interface between the test subject and the device. Data is also obtained using free weights for a comparison to the resistively loaded exercise device. This data is input into the OpenSim biomechanical model, which has been scaled to match the anthropometrics of the test subject, to calculate the body loads. The focus of this presentation is to summarize the results from the full squat exercises

  1. The ultimate response guideline simulation and analysis by using (TRACE) for Lungmen ABWR nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Hao-Tzu [Atomic Energy Council, Inst. of Nuclear Energy Research, Taoyuan City, Taiwan (China); Yang, Shu-Ming; Chen, Shao-Wen; Wang, Jong-Rong; Shih, Chunkuan [National Tsing Hua Univ., Inst. of Nuclear Engineering and Science, HsinChu, Taiwan (China)

    2015-07-15

    In this research, the TRACE/SNAP model of Lungmen ABWR nuclear power plant (NPP) has been established for the simulation and analysis of ultimate response guideline (URG). The main actions of URG are depressurization and low pressure water injection of reactor and containment venting. This research focuses to assess the URG utility of Lungmen NPP under Fukushima-like conditions. This study consists of three steps. The first step is the establishment of Lungmen NPP TRACE/SNAP model. In order to evaluate the system response of TRACE/SNAP model, FSAR data (MSIV closure and loss of feedwater flow transient) were used to compare with the results of TRACE. The second step is the URG simulation and analysis under Fukushima-like conditions by using Lungmen NPP TRACE/SNAP model. In this step, the no URG case was also performed in order to evaluate the URG effectiveness of Lungmen NPP. In order to confirm the mechanical property and integrity of fuel rods, the final step is FRAPTRAN analysis. According to TRACE analysis results, the URG can keep the peak cladding temperature (PCT) below the criteria 1088.7 K under Fukushima-like conditions which indicates that Lungmen NPP can be controlled in a safe situation. Nevertheless, if Lungmen NPP does not perform the URG under Fukushima-like conditions, the water level may drop lower than TAF after 1100 s which means a safety issue about the fuel rods may be generated. The analysis results of FRAPTRAN also indicate the integrity of fuel rods cannot be kept under the above conditions.

  2. The in vitro digestibility of beef varies with its inherent ultimate pH.

    Science.gov (United States)

    Farouk, Mustafa M; Wu, Guojie; Frost, Deborah A; Clerens, Stefan; Knowles, Scott O

    2014-11-01

    Animal carcasses and cuts of meat are usually differentiated and valued according to size and compositional attributes. An underappreciated variable of red meat is its inherent ultimate pH (pHu) value, which affects organoleptic and processing characteristics. This study tests the hypothesis that high pHu aged meat would be more digestible than low pHu unaged (fresh) meat. Longissimus dorsi muscles collected from 59 bull carcasses had pHu values of 5.6-6.9. These were aged for 21 days at -1.5 °C, then raw and cooked (72 °C) samples were enzymatically digested at 37 °C with pepsin (pH 1.9 for 90 min) followed by pancreatin (pH 8.0 for an additional 120 min) to simulate conditions in the stomach and small intestine, respectively. Meat proteins and peptides in the digests were separated by 1D SDS PAGE. Regardless of pHu, ageing or cooking, most sarcoplasmic and myofibrillar proteins were rapidly digested by pepsin, with concomitant release of products identified by LC-MS/MS as mainly myosin-1, -2 and -7, α-actinin-2 or -3 and tropomyosin beta and alpha chains. These products were resistant to further digestion for the entire 210 min duration of the incubation. In terms of rate and extent of digestibility of these resistant products, high pHu > low pHu (P unaged (P meat samples increased with increasing pHu (P meat was highly digestible but could be further differentiated on the basis of its pHu and the ease of digestibility of proteins. Specific carcasses or cuts could be targeted to consumer groups in order to provide benefits and add value.

  3. Long-time safety aspects of ultimate storage of transuranium elements

    International Nuclear Information System (INIS)

    Storck, R.

    1992-10-01

    Based on the amounts of transuranium elements generated in nuclear reactors, the inventories of these elements in the repository are described for various ultimate disposal strategies. The data are used to give an outline description of accident-induced ingress of brines into the backfilled repository shaft during the post-closure period and the resulting mechanisms of a mobilization of the transuranium elements and their escape from the repository, and to calculate amounts released. The effects of the released transuranium elements on the biosphere and the different contributions of the various isotopes to the calculated radiation exposure are given as an estimate and are described in more detail by means of data determined by parameter variation. The effects of transuranium elements during the entire migration process are restricted to the production of daughter nuclides, especially of the uranium isotopes. They give no particular contribution to environmental radiation exposure because of their low mobility. With the only exception of Np-237 which, due to its long half-time and relatively good migration capacity, can reach the biosphere. The contributions of the transuranium elements to the dose maxima, caused by the daughter products, of the uranium isotopes or the neptunium are calculated to be about 50%. All publications to date presenting a safety analysis of the site of the Gorleben repository assume the dose maxima of all uranium isotopes together to be approx. 10%, and those of the neptunium isotope approx. 20%, referring to the most significant fission products. This indicates that uranium or neptunium are of secondary significance in the process, and the other transuranium elements are only third-rate. (orig./HP) [de

  4. BNL NONLINEAR PRE TEST SEISMIC ANALYSIS FOR THE NUPEC ULTIMATE STRENGTH PIPING TEST PROGRAM

    International Nuclear Information System (INIS)

    DEGRASSI, G.; HOFMAYER, C.; MURPHY, C.; SUZUKI, K.; NAMITA, Y.

    2003-01-01

    The Nuclear Power Engineering Corporation (NUPEC) of Japan has been conducting a multi-year research program to investigate the behavior of nuclear power plant piping systems under large seismic loads. The objectives of the program are: to develop a better understanding of the elasto-plastic response and ultimate strength of nuclear piping; to ascertain the seismic safety margin of current piping design codes; and to assess new piping code allowable stress rules. Under this program, NUPEC has performed a large-scale seismic proving test of a representative nuclear power plant piping system. In support of the proving test, a series of materials tests, static and dynamic piping component tests, and seismic tests of simplified piping systems have also been performed. As part of collaborative efforts between the United States and Japan on seismic issues, the US Nuclear Regulatory Commission (USNRC) and its contractor, the Brookhaven National Laboratory (BNL), are participating in this research program by performing pre-test and post-test analyses, and by evaluating the significance of the program results with regard to safety margins. This paper describes BNL's pre-test analysis to predict the elasto-plastic response for one of NUPEC's simplified piping system seismic tests. The capability to simulate the anticipated ratcheting response of the system was of particular interest. Analyses were performed using classical bilinear and multilinear kinematic hardening models as well as a nonlinear kinematic hardening model. Comparisons of analysis results for each plasticity model against test results for a static cycling elbow component test and for a simplified piping system seismic test are presented in the paper

  5. The Ultimate Pile Bearing Capacity from Conventional and Spectral Analysis of Surface Wave (SASW) Measurements

    Science.gov (United States)

    Faizah Bawadi, Nor; Anuar, Shamilah; Rahim, Mustaqqim A.; Mansor, A. Faizal

    2018-03-01

    A conventional and seismic method for determining the ultimate pile bearing capacity was proposed and compared. The Spectral Analysis of Surface Wave (SASW) method is one of the non-destructive seismic techniques that do not require drilling and sampling of soils, was used in the determination of shear wave velocity (Vs) and damping (D) profile of soil. The soil strength was found to be directly proportional to the Vs and its value has been successfully applied to obtain shallow bearing capacity empirically. A method is proposed in this study to determine the pile bearing capacity using Vs and D measurements for the design of pile and also as an alternative method to verify the bearing capacity from the other conventional methods of evaluation. The objectives of this study are to determine Vs and D profile through frequency response data from SASW measurements and to compare pile bearing capacities obtained from the method carried out and conventional methods. All SASW test arrays were conducted near the borehole and location of conventional pile load tests. In obtaining skin and end bearing pile resistance, the Hardin and Drnevich equation has been used with reference strains obtained from the method proposed by Abbiss. Back analysis results of pile bearing capacities from SASW were found to be 18981 kN and 4947 kN compared to 18014 kN and 4633 kN of IPLT with differences of 5% and 6% for Damansara and Kuala Lumpur test sites, respectively. The results of this study indicate that the seismic method proposed in this study has the potential to be used in estimating the pile bearing capacity.

  6. Effect of Incorporation of Antifungal Agents on the Ultimate Tensile Strength of Temporary Soft Denture Liners.

    Science.gov (United States)

    Neppelenbroek, Karin Hermana; Lima, Jozely Francisca Mello; Hotta, Juliana; Galitesi, Lucas Lulo; Almeida, Ana Lucia Pompéia Fraga; Urban, Vanessa Migliorini

    2018-02-01

    To investigate the ultimate tensile strength of temporary soft denture liners modified by minimum inhibitory concentrations (MICs) of antifungal agents for Candida albicans biofilm (SC5314) determined in previous microbiological research. Dumbbell-shaped specimens (n = 7) with a central cross-sectional area of 6 × 3 × 33 mm were produced by Softone and Trusoft, without (control) or with incorporation of drugs in powder form at MICs for C. albicans biofilm (per g of material powder): nystatin (0.032 g), chlorhexidine diacetate (0.064 g), ketoconazole (0.128 g), miconazole (0.256 g), and itraconazole (0.256 g). After plasticization, specimens were immersed in distilled water at 37°C for 24 hours, 7 or 14 days, and then tested in tension in a universal testing machine at 40 mm/min. Data of tensile strength (MPa) and elongation percentage (%) were submitted to 3-way ANOVA and Tukey's test (α = 0.05). At the end of 14 days, the tensile strength for both materials was significantly lower in the groups modified by miconazole and itraconazole compared to the other groups (p 0.05). After 7 and 14 days in water, miconazole and itraconazole added into both materials resulted in significantly lower elongation percentages compared to the other antifungal agents and control (p 0.05). The addition of the nystatin, chlorhexidine, and ketoconazole at MICs for C. albicans biofilm resulted in no harmful effects on the tensile strength and elongation percentage of the temporary soft denture liner materials up to 14 days. © 2017 by the American College of Prosthodontists.

  7. Different Ultimate Factors Define Timing of Breeding in Two Related Species.

    Directory of Open Access Journals (Sweden)

    Veli-Matti Pakanen

    Full Text Available Correct reproductive timing is crucial for fitness. Breeding phenology even in similar species can differ due to different selective pressures on the timing of reproduction. These selection pressures define species' responses to warming springs. The temporal match-mismatch hypothesis suggests that timing of breeding in animals is selected to match with food availability (synchrony. Alternatively, time-dependent breeding success (the date hypothesis can result from other seasonally deteriorating ecological conditions such as intra- or interspecific competition or predation. We studied the effects of two ultimate factors on the timing of breeding, synchrony and other time-dependent factors (time-dependence, in sympatric populations of two related forest-dwelling passerine species, the great tit (Parus major and the willow tit (Poecile montanus by modelling recruitment with long-term capture-recapture data. We hypothesized that these two factors have different relevance for fitness in these species. We found that local recruitment in both species showed quadratic relationships with both time-dependence and synchrony. However, the importance of these factors was markedly different between the studied species. Caterpillar food played a predominant role in predicting the timing of breeding of the great tit. In contrast, for the willow tit time-dependence modelled as timing in relation to conspecifics was more important for local recruitment than synchrony. High caterpillar biomass experienced during the pre- and post-fledging periods increased local recruitment of both species. These contrasting results confirm that these species experience different selective pressures upon the timing of breeding, and hence responses to climate change may differ. Detailed information about life-history strategies is required to understand the effects of climate change, even in closely related taxa. The temporal match-mismatch hypothesis should be extended to consider

  8. Assessment of cooling tower (ultimate heat sink) performance in the Byron individual plant examination

    International Nuclear Information System (INIS)

    Campbell, H.D.; Hawley, J.T.; Klopp, G.T.; Thelen, W.A.

    2004-01-01

    A time-dependent model of the Byron Nuclear Generation Station safety-related cooling towers has been developed for use with the Byron PRA (IPE). The model can either be run in a stand-alone program with externally supplied heat loads, or can be directly coupled into MAAP (Modular Accident Analysis Program). The primary feature of the model is a careful tracking of the basin temperature through the progression of different severe accidents. Heat removal rates from containment, both from containment fan-coolers and the residual heat removal system, are determined by the feed-back of this time-varying return temperature. Also, the inventory of the basin is tracked in time, and this is controlled by make-up, evaporative losses due to the heat load supplied to the towers, and the possibility of unsecured blowdown. The model has been used to determine the overall capabilities and vulnerabilities of the Byron Ultimate Heat Sink (UHS). It was determined that the UHS is very reliable with respect to maintaining acceptably low basin temperatures, requiring only at most two of eight operating cooling tower fans. Further, when the two units have their Essential Service Water (ESW) systems cross-tied, one of four ESW operating pumps is sufficient to handle the loads from the accident unit with the other unit proceeding to an orderly shutdown. The major vulnerability of the Byron UHS is shown to be the ability to maintain inventory, although the time-scales for basin dry-out are relatively long, being eight to twenty-one hours, depending upon when blowdown is secured. (author)

  9. Proximate and ultimate controls on carbon and nutrient dynamics of small agricultural catchments

    Science.gov (United States)

    Thomas, Zahra; Abbott, Benjamin W.; Troccaz, Olivier; Baudry, Jacques; Pinay, Gilles

    2016-03-01

    Direct and indirect effects from human activity have dramatically increased nutrient loading to aquatic inland and estuarine ecosystems. Despite an abundance of studies investigating the impact of agricultural activity on water quality, our understanding of what determines the capacity of a watershed to remove or retain nutrients remains limited. The goal of this study was to identify proximate and ultimate controls on dissolved organic carbon and nutrient dynamics in small agricultural catchments by investigating the relationship between catchment characteristics, stream discharge, and water chemistry. We analyzed a 5-year, high-frequency water chemistry data set from three catchments in western France ranging from 2.3 to 10.8 km2. The relationship between hydrology and solute concentrations differed between the three catchments and was associated with hedgerow density, agricultural activity, and geology. The catchment with thicker soil and higher surface roughness had relatively invariant carbon and nutrient chemistry across hydrologic conditions, indicating high resilience to human disturbance. Conversely, the catchments with smoother, thinner soils responded to both intra- and interannual hydrologic variation with high concentrations of phosphate (PO43-) and ammonium (NH4+) in streams during low flow conditions and strong increases in dissolved organic carbon (DOC), sediment, and particulate organic matter during high flows. Despite contrasting agricultural activity between catchments, the physical context (geology, topography, and land-use configuration) appeared to be the most important determinant of catchment solute dynamics based on principle components analysis. The influence of geology and accompanying topographic and geomorphological factors on water quality was both direct and indirect because the distribution of agricultural activity in these catchments is largely a consequence of the geologic and topographic context. This link between inherent

  10. Research and development on ultimate storage of radioactive wastes. Annual report, 1977

    International Nuclear Information System (INIS)

    The present deals with the activities of the Entwicklungsgemeinschaft Tieflagerung which was founded on 1 January 1978 and consists of institutes, branches and working groups both of the Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen and the Kernforschungszentrum Karlsruhe which are engaged in the field of radioactive waste disposal. This report presents a survey of the work performed in that field in 1977. The mining and construction work is discussed, which was carried out both underground and above at the Asse Salt Mine near Remlingen and which was done for repair, maintenance, and expansion of operation in accordance with its future purpose. The experimental disposal of low-level wastes on the 750-m and 725-m level was continued in the time period under review. Only seven drums of intermediate-level waste were experimentally disposed of in 1977. The disposal field and the operational equipment for the single test disposal of spent fuel elements from the AVR reactor were completed and are ready for operation. Due to legal, political, and transport problems there is a delay of the start of the test disposal. The mining of the prototype cavity was finished reaching a fina depth of 996.1 m. Moreover, the report gives information on means for radiation protection and the results of the environmental surveillance program. Also the present status of the research activities and their results, especially in the field of disposal of high-level waste, rock mechanics, and safety studies is reported

  11. A Polynomial Estimate of Railway Line Delay

    DEFF Research Database (Denmark)

    Cerreto, Fabrizio; Harrod, Steven; Nielsen, Otto Anker

    2017-01-01

    Railway service may be measured by the aggregate delay over a time horizon or due to an event. Timetables for railway service may dampen aggregate delay by addition of additional process time, either supplement time or buffer time. The evaluation of these variables has previously been performed...... by numerical analysis with simulation. This paper proposes an analytical estimate of aggregate delay with a polynomial form. The function returns the aggregate delay of a railway line resulting from an initial, primary, delay. Analysis of the function demonstrates that there should be a balance between the two...

  12. Delay Variation Model with Two Service Queues

    Directory of Open Access Journals (Sweden)

    Filip Rezac

    2010-01-01

    Full Text Available Delay in VoIP technology is very unpleasant issue and therefore a voice packets prioritization must be ensured. To maintain the high call quality a maximum information delivery time from the sender to the recipient is set to 150 ms. This paper focuses on the design of a mathematical model of end-to-end delay of a VoIP connection, in particular on a delay variation. It describes all partial delay components and mechanisms, their generation, facilities and mathematical formulations. A new approach to the delay variation model is presented and its validation has been done by experimention.

  13. Fuzzy delay model based fault simulator for crosstalk delay fault test ...

    Indian Academy of Sciences (India)

    In this paper, a fuzzy delay model based crosstalk delay fault simulator is proposed. As design trends move towards nanometer technologies, more number of new parameters affects the delay of the component. Fuzzy delay models are ideal for modelling the uncertainty found in the design and manufacturing steps.

  14. A Fast Time-Delay Calculation Method in Through-Wall-Radar Detection Scenario

    Directory of Open Access Journals (Sweden)

    Zhang Qi

    2016-01-01

    Full Text Available In TWR (Through Wall Radar signal processing procedure, time delay estimation is one of the key steps in target localization and high resolution imaging. In time domain imaging procedure such as back projection imaging algorithm, round trip propagation time delay at the path of “transmitter-target-receiver” needs to be calculated for each pixel in imaging region. In typical TWR scenario, transmitter and receiver are at one side and targets at the other side of a wall. Based on two-dimensional searching algorithm or solving two variables equation of four times, traditional time delay calculation algorithms are complex and time consuming, and cannot be used to real-time imaging procedure. In this paper, a new fast time-delay (FTD algorithm is presented. Because of that incident angle at one side equals to refracting angle at the other side, an equation of lateral distance through the wall can be established. By solving this equation, the lateral distance can be obtained and total propagation time delay can be calculated subsequently. Through processing simulation data, the result shows that new algorithm can be applied effectively to real-time time-delay calculation in TWR signal processing.

  15. On the synchronization of neural networks containing time-varying delays and sector nonlinearity

    International Nuclear Information System (INIS)

    Yan, J.-J.; Lin, J.-S.; Hung, M.-L.; Liao, T.-L.

    2007-01-01

    We present a systematic design procedure for synchronization of neural networks subject to time-varying delays and sector nonlinearity in the control input. Based on the drive-response concept and the Lyapunov stability theorem, a memoryless decentralized control law is proposed which guarantees exponential synchronization even when input nonlinearity is present. The supplementary requirement that the time-derivative of time-varying delays must be smaller than one is released for the proposed control scheme. A four-dimensional Hopfield neural network with time-varying delays is presented as the illustrative example to demonstrate the effectiveness of the proposed synchronization scheme

  16. HASL procedures manual

    International Nuclear Information System (INIS)

    Harley, J.H.

    1977-08-01

    Additions and corrections to the following sections of the HASL Procedures Manual are provided: General, Sampling, Field Measurements; General Analytical Chemistry, Chemical Procedures, Data Section, and Specifications

  17. Procedure automation: the effect of automated procedure execution on situation awareness and human performance

    International Nuclear Information System (INIS)

    Andresen, Gisle; Svengren, Haakan; Heimdal, Jan O.; Nilsen, Svein; Hulsund, John-Einar; Bisio, Rossella; Debroise, Xavier

    2004-04-01

    As advised by the procedure workshop convened in Halden in 2000, the Halden Project conducted an experiment on the effect of automation of Computerised Procedure Systems (CPS) on situation awareness and human performance. The expected outcome of the study was to provide input for guidance on CPS design, and to support the Halden Project's ongoing research on human reliability analysis. The experiment was performed in HAMMLAB using the HAMBO BWR simulator and the COPMA-III CPS. Eight crews of operators from Forsmark 3 and Oskarshamn 3 participated. Three research questions were investigated: 1) Does procedure automation create Out-Of-The-Loop (OOTL) performance problems? 2) Does procedure automation affect situation awareness? 3) Does procedure automation affect crew performance? The independent variable, 'procedure configuration', had four levels: paper procedures, manual CPS, automation with breaks, and full automation. The results showed that the operators experienced OOTL problems in full automation, but that situation awareness and crew performance (response time) were not affected. One possible explanation for this is that the operators monitored the automated procedure execution conscientiously, something which may have prevented the OOTL problems from having negative effects on situation awareness and crew performance. In a debriefing session, the operators clearly expressed their dislike for the full automation condition, but that automation with breaks could be suitable for some tasks. The main reason why the operators did not like the full automation was that they did not feel being in control. A qualitative analysis addressing factors contributing to response time delays revealed that OOTL problems did not seem to cause delays, but that some delays could be explained by the operators having problems with the freeze function of the CPS. Also other factors such as teamwork and operator tendencies were of importance. Several design implications were drawn

  18. Precise delay measurement through combinatorial logic

    Science.gov (United States)

    Burke, Gary R. (Inventor); Chen, Yuan (Inventor); Sheldon, Douglas J. (Inventor)

    2010-01-01

    A high resolution circuit and method for facilitating precise measurement of on-chip delays for FPGAs for reliability studies. The circuit embeds a pulse generator on an FPGA chip having one or more groups of LUTS (the "LUT delay chain"), also on-chip. The circuit also embeds a pulse width measurement circuit on-chip, and measures the duration of the generated pulse through the delay chain. The pulse width of the output pulse represents the delay through the delay chain without any I/O delay. The pulse width measurement circuit uses an additional asynchronous clock autonomous from the main clock and the FPGA propagation delay can be displayed on a hex display continuously for testing purposes.

  19. Reasons for diagnostic delay in gynecological malignancies

    DEFF Research Database (Denmark)

    Vandborg, Mai Partridge; Christensen, René dePont Christensen; Kragstrup, Jakob

    2011-01-01

    (≤ or > 60 years), performance of gynecological examination by the GP and notification of cancer suspicion on first referral from GP’s on the diagnostic delay (short delay ≤90 days and long delay >90 days). Results Across cancer type a median total delay of 101 days was observed. The 10% of women......Aim The primary aim of this study was to identify and describe different delay types in women with gynecologic cancer, and to analyze the relationship between diagnostic delay and a number of characteristics for patients, cancers and the health care system. Setting A cohort study of women newly......) and The Danish Gynecological Cancer Database (DGCD). 161 women were included; ovarian cancer: 63, endometrial cancer: 50, cervical cancer: 34 and vulvar cancer: 14. Outcome measures were different delay types counted in days and the influence of four clinical important variables: Presence of alarm symptoms, age...

  20. Temperature Dependent Wire Delay Estimation in Floorplanning

    DEFF Research Database (Denmark)

    Winther, Andreas Thor; Liu, Wei; Nannarelli, Alberto

    2011-01-01

    Due to large variations in temperature in VLSI circuits and the linear relationship between metal resistance and temperature, the delay through wires of the same length can be different. Traditional thermal aware floorplanning algorithms use wirelength to estimate delay and routability. In this w......Due to large variations in temperature in VLSI circuits and the linear relationship between metal resistance and temperature, the delay through wires of the same length can be different. Traditional thermal aware floorplanning algorithms use wirelength to estimate delay and routability....... In this work, we show that using wirelength as the evaluation metric does not always produce a floorplan with the shortest delay. We propose a temperature dependent wire delay estimation method for thermal aware floorplanning algorithms, which takes into account the thermal effect on wire delay. The experiment...

  1. Elite athletes and pubertal delay.

    Science.gov (United States)

    Kapczuk, Karina

    2017-10-01

    Intensive physical training and participation in competitive sports during childhood and early adolescence may affect athletes' pubertal development. On the other hand, pubertal timing, early or late, may impact on an athlete selection for a particular sport. Genetic predisposition, training load, nutritional status and psychological stress determine athletes' pubertal timing. Athletes that practice esthetic sports, especially gymnasts, are predisposed to a delay in pubertal development. The growing evidence indicates that energy deficiency, not a systemic training per se, plays a crucial role in the pathogenesis of functional hypothalamic hypogonadism in female athletes. Metabolic and psychologic stress activate hypothalamic-pituitary-adrenal axis and suppress hypothalamic-pituitary-ovarian axis. Female athletes who do not begin secondary sexual development by the age of 14 or menstruation by the age of 16 warrant a comprehensive evaluation and a targeted treatment. Somatic growth and sexual maturation of elite female athletes are largely sport-specific since each sport favors a particular somatotype and requires a specific training. Chronic negative energy balance resulting from a systemic physical training and inadequate energy intake may delay pubertal development in elite athletes. Youth athletes, especially those engaged in competitive sports that emphasize prepubertal or lean appearance, are at risk of developing relative energy deficiency in sport associated with disordered eating or eating disorders. Management strategies should address the complex conditions underlying functional hypothalamic hypogonadism.

  2. Delayed recombination and cosmic parameters

    International Nuclear Information System (INIS)

    Galli, Silvia; Melchiorri, Alessandro; Bean, Rachel; Silk, Joseph

    2008-01-01

    Current cosmological constraints from cosmic microwave background anisotropies are typically derived assuming a standard recombination scheme, however additional resonance and ionizing radiation sources can delay recombination, altering the cosmic ionization history and the cosmological inferences drawn from the cosmic microwave background data. We show that for recent observations of the cosmic microwave background anisotropy, from the Wilkinson microwave anisotropy probe satellite mission (WMAP) 5-year survey and from the arcminute cosmology bolometer array receiver experiment, additional resonance radiation is nearly degenerate with variations in the spectral index, n s , and has a marked effect on uncertainties in constraints on the Hubble constant, age of the universe, curvature and the upper bound on the neutrino mass. When a modified recombination scheme is considered, the redshift of recombination is constrained to z * =1078±11, with uncertainties in the measurement weaker by 1 order of magnitude than those obtained under the assumption of standard recombination while constraints on the shift parameter are shifted by 1σ to R=1.734±0.028. From the WMAP5 data we obtain the following constraints on the resonance and ionization sources parameters: ε α i <0.058 at 95% c.l.. Although delayed recombination limits the precision of parameter estimation from the WMAP satellite, we demonstrate that this should not be the case for future, smaller angular scales measurements, such as those by the Planck satellite mission.

  3. Asymptotic Delay Analysis for Cross-Layer Delay-Based Routing in Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Philippe Jacquet

    2007-01-01

    Full Text Available This paper addresses the problem of the evaluation of the delay distribution via analytical means in IEEE 802.11 wireless ad hoc networks. We show that the asymptotic delay distribution can be expressed as a power law. Based on the latter result, we present a cross-layer delay estimation protocol and we derive new delay-distribution-based routing algorithms, which are well adapted to the QoS requirements of real-time multimedia applications. In fact, multimedia services are not sensitive to average delays, but rather to the asymptotic delay distributions. Indeed, video streaming applications drop frames when they are received beyond a delay threshold, determined by the buffer size. Although delay-distribution-based routing is an NP-hard problem, we show that it can be solved in polynomial time when the delay threshold is large, because of the asymptotic power law distribution of the link delays.

  4. Geologic mapping procedure: Final draft

    International Nuclear Information System (INIS)

    1987-09-01

    Geologic mapping will provide a baseline record of the subsurface geology in the shafts and drifts of the Exploratory Shaft Facility (ESF). This information will be essential in confirming the specific repository horizon, selecting representative locations for the in situ tests, providing information for construction and decommissioning seal designs, documenting the excavation effects, and in providing information for performance assessment, which relates to the ultimate suitability of the site as a nuclear waste repository. Geologic mapping will be undertaken on the walls and roof, and locally on the floor within the completed At-Depth Facility (ADF) and on the walls of the two access shafts. Periodic mapping of the exposed face may be conducted during construction of the ADF. The mapping will be oriented toward the collection and presentation of geologic information in an engineering format and the portrayal of detailed stratigraphic information which may be useful in confirmation of drillhole data collected as part of the surface-based testing program. Geologic mapping can be considered as a predictive tool as well as a means of checking design assumptions. This document provides a description of the required procedures for geologic mapping for the ESF. Included in this procedure is information that qualified technical personnel can use to collect the required types of geologic descriptions, at the appropriate level of detail. 5 refs., 3 figs., 1 tab

  5. Concept for an ultimate storage facility for heat-generating radioactive waste in clay stone in Germany

    International Nuclear Information System (INIS)

    Bollingerfehr, Wilhelm; Poehler, Matthias

    2010-01-01

    According to the German reference ultimate storage concept heat-generating radioactive waste from the operation of nuclear power stations should be stored permanently maintenance-free and in a non-recoverable manner in a salt formation. Within the framework of investigations into the utilisation of alternative host rocks a concept for an ultimate storage facility in clay stone was developed in an R and D project. For this purpose all important aspects of the design, development, operation and shutdown were taken into account for a model region in northern Germany. It was established that storage in 50 m deep vertical boreholes in a mine at a depth of about 350 m appears to be the most practical solution for an ultimate storage facility in clay stone. Compared to the reference concept in salt an ultimate storage facility in clay stone requires solid support of all mine openings with steel arches or shotcrete. Because of the lower maximum permissible temperature in the backfilling material (bentonite) the area required for the ultimate storage facility is about five times larger. A period of more than 100 years is estimated from survey to shutdown. (orig.)

  6. Maximal monotone model with delay term of convolution

    Directory of Open Access Journals (Sweden)

    Claude-Henri Lamarque

    2005-01-01

    Full Text Available Mechanical models are governed either by partial differential equations with boundary conditions and initial conditions (e.g., in the frame of continuum mechanics or by ordinary differential equations (e.g., after discretization via Galerkin procedure or directly from the model description with the initial conditions. In order to study dynamical behavior of mechanical systems with a finite number of degrees of freedom including nonsmooth terms (e.g., friction, we consider here problems governed by differential inclusions. To describe effects of particular constitutive laws, we add a delay term. In contrast to previous papers, we introduce delay via a Volterra kernel. We provide existence and uniqueness results by using an Euler implicit numerical scheme; then convergence with its order is established. A few numerical examples are given.

  7. Predictors of binge drinking in adolescents: ultimate and distal factors - a representative study

    Directory of Open Access Journals (Sweden)

    Donath Carolin

    2012-04-01

    Full Text Available Abstract Background As epidemiological surveys have shown, binge drinking is a constant and wide-spread problem behavior in adolescents. It is not rare to find that more than half of all adolescents engage in this behavior when assessing only the last 4 weeks of time independent of the urbanity of the region they live in. There have been several reviews on predictors of substance consumption in adolescents in general, but there has been less high quality research on predictors of binge drinking, and most studies have not been theoretically based. The current study aimed to analyze the ultimate and distal factors predicting substance consumption according to Petraitis' theory of triadic influence. We assessed the predictive value of these factors with respect to binge drinking in German adolescents, including the identification of influence direction. Methods In the years 2007/2008, a representative written survey of N = 44,610 students in the 9th grade of different school types in Germany was carried out (net sample. The return rate of questionnaires was 88% regarding all students whose teachers or school directors had agreed to participate in the study. In this survey, prevalence of binge drinking was investigated as well as potential predictors from the social/interpersonal, the attitudinal/environmental, and the intrapersonal fields (3 factors of Petraitis. In a multivariate logistic regression analysis, these variables were included after testing for multicollinearity in order to assess their ability to predict binge drinking. Results Prevalence of binge drinking in the last 30 days was 52.3% for the surveyed adolescents with a higher prevalence for boys (56.9% than for girls (47.5%. The two most influential factors found to protect against binge drinking with p p Conclusions Whereas some of the risk and protective factors for binge drinking are not surprising since they are known for substance abuse in general, there are two points that

  8. Proximate and Ultimate Compositional Changes in Corn Stover during Torrefaction using Thermogravimetric Analyzer and Microwaves

    Energy Technology Data Exchange (ETDEWEB)

    Jaya Shankar Tumuluru

    2012-07-01

    regular and microwaves and their effect on proximate and ultimate composition. Studies indicated that microwave torrefaction is a good way to torrefy the biomass in short periods of time. A maximum calorific value of 21 MJ/kg is achievable at 6 min residence time compared to 15 min using the dry torrefaction technique. Increasing the residence time increased the carbon content where a maximum carbon content of 52.20 % was achievable at lower residence time. The loss of volatiles is comparatively lower compared to dry torrefaction technique. Moisture content of microwave torrefied samples was in between 2-2.5 % (w.b).

  9. Ultimate Tensile Strength as a Function of Test Rate for Various Ceramic Matrix Composites at Elevated Temperatures

    Science.gov (United States)

    Choi, Sung R.; Bansal, Narottam P.; Gyekenyesi, John P.

    2002-01-01

    Ultimate tensile strength of five different continuous fiber-reinforced ceramic composites, including SiC/BSAS (2D 2 types), SiC/MAS-5 (2D), SiC/SiC (2D enhanced), and C/SiC(2D) was determined as a function of test rate at I 100 to 1200 'C in air. All five composite materials exhibited a significant dependency of ultimate strength on test rate such that the ultimate strength decreased with decreasing test rate, similar to the behavior observed in many advanced monolithic ceramics at elevated temperatures. The application of the preloading technique as well as the prediction of life from one loading configuration (constant stress rate) to another (constant stress loading) for SiC/BSAS suggested that the overall macroscopic failure mechanism of the composites would be the one governed by a power-law type of damage evolution/accumulation, analogous to slow crack growth commonly observed in advanced monolithic ceramics.

  10. Duties of the Physikalisch-Technische Bundesanstalt (PTB) in connection with radioactive waste safeguarding and ultimate storage

    International Nuclear Information System (INIS)

    Roethemeyer, H.

    1977-01-01

    An outline of the history and duties of the Physikalisch-Technische Bundesanstalt (PTB) is to illustrate that the new duties of the PTB in connection with radioactive substance safeguarding and ultimate storage fit in very well with the range of duties of the PTB. The organisatory and technical accomplishment of these duties in cooperation with a building and operating company and with industry is explained. The department of the PTB for the 'safeguarding and ultimate storage of radioactive wastes' has an examining, appraising and licensing function in connection with construction, operation and shutdown of safety facilities. Methods for the safeguarding and ultimate storage of all the radioactive wastes in the Federal Republic of Germany are described. (HS) [de

  11. Experimental research on the ultimate strength of hard aluminium alloy 2017 subjected to short-time radioactive heating

    International Nuclear Information System (INIS)

    Dafang, Wu; Yuewu, Wang; Bing, Pan; Meng, Mu; Lin, Zhu

    2012-01-01

    Highlights: ► Ultimate strength at transient heating is critical to security design of missiles. ► We measure the ultimate strength of alloy 2017 subjected to transient heating. ► Experimental results at transient heating are lacking in strength design handbook. ► Ultimate strength of alloy 2017 experimented is much higher than handbook value. ► The results provide a new method for optimal design of high-speed flight vehicles. -- Abstract: Alloy 2017 (Al–Cu–Mg) is a hard aluminium alloy strengthened by heat treatment. Because of its higher strength, finer weldability and ductility, hard aluminium alloy 2017 has been widely used in the field of aeronautics and astronautics. However, the ultimate strength and other characteristic mechanical parameters of aluminium alloy 2017 in a transient heating environment are still unclear, as these key mechanical parameters are lacking in the existing strength design handbook. The experimental characterisation of these critical parameters of aluminium alloy 2017 is undoubtedly meaningful for reliably estimating life span of and improving safety in designing high-speed flight vehicles. In this paper, the high-temperature ultimate strength, loading time and other mechanical properties of hard aluminium alloy 2017 under different transient heating temperatures and loading conditions are investigated by combining a transient aerodynamic heating simulation system and a material testing machine. The experimental results reveal that the ultimate strength and loading capability of aluminium alloy 2017 subjected to transient thermal heating are much higher than those tested in a long-time stable high-temperature environment. The research of this work not only provides a substantial basis for the loading capability improvement and optimal design of aerospace materials and structures subject to transient heating but also presents a new research direction with a practical application value.

  12. Risk factors for delayed healing at the free anterolateral thigh flap donor site

    Directory of Open Access Journals (Sweden)

    Yoshiro Abe

    2018-01-01

    Full Text Available Background The free anterolateral thigh (ALT flap has been widely used for various kinds of reconstructions. However, delayed healing at the donor site occasionally occurs due to wound dehiscence or the partial loss of grafted skin at the donor site. The aim of the present study was to identify reliable predictive factors for delayed healing at the donor site after the harvest of a free ALT flap. Methods This study included 52 patients who underwent reconstructive procedures using free ALT flaps. The delayed healing group included patients with wounds at the donor site that had not healed over 3 weeks after surgery, and the normal healing group included patients who showed wound healing within 3 weeks after surgery. Multivariate logistic regression models were created to identify the risk factors for delayed healing at the ALT flap donor site. Results Among the 52 patients, 24 (46.2% showed delayed healing at the donor site, and 6 patients required additional operative treatment. A high preoperative body mass index (BMI, smoking, and skin grafting were found to be significantly associated with delayed healing at the ALT donor site. Of the 37 patients who underwent skin grafting, 23 (62% experienced delayed healing at the donor site. Conclusions A high preoperative BMI, smoking, and skin grafting were risk factors for delayed healing at the free ALT donor site. Skin grafting at the ALT donor site should be avoided in patients with a high BMI or a habit of smoking.

  13. Dynamic IQC-Based Control of Uncertain LFT Systems With Time-Varying State Delay.

    Science.gov (United States)

    Yuan, Chengzhi; Wu, Fen

    2016-12-01

    This paper presents a new exact-memory delay control scheme for a class of uncertain systems with time-varying state delay under the integral quadratic constraint (IQC) framework. The uncertain system is described as a linear fractional transformation model including a state-delayed linear time-invariant (LTI) system and time-varying structured uncertainties. The proposed exact-memory delay controller consists of a linear state-feedback control law and an additional term that captures the delay behavior of the plant. We first explore the delay stability and the L 2 -gain performance using dynamic IQCs incorporated with quadratic Lyapunov functions. Then, the design of exact-memory controllers that guarantee desired L 2 -gain performance is examined. The resulting delay control synthesis conditions are formulated in terms of linear matrix inequalities, which are convex on all design variables including the scaling matrices associated with the IQC multipliers. The IQC-based exact-memory control scheme provides a novel approach for delay control designs via convex optimization, and advances existing control methods in two important ways: 1) better controlled performance and 2) simplified design procedure with less computational cost. The effectiveness and advantages of the proposed approach have been demonstrated through numerical studies.

  14. Pinning synchronization of hybrid-coupled directed delayed dynamical network via intermittent control.

    Science.gov (United States)

    Cai, Shuiming; Zhou, Peipei; Liu, Zengrong

    2014-09-01

    This paper concerns the problem of exponential synchronization for a class of general delayed dynamical networks with hybrid coupling via pinning periodically intermittent control. Both the internal delay and coupling delay are taken into account in the network model. Meanwhile, the transmission delay and self-feedback delay are involved in the delayed coupling term. By establishing a new differential inequality, several simple and useful exponential synchronization criteria are derived analytically. It is shown that the controlled synchronization state can vary in comparison with the conventional synchronized solution, and the degree of the node and the inner delayed coupling matrix play important roles in the controlled synchronization state. By choosing different inner delayed coupling matrices and the degrees of the node, different controlled synchronization states can be obtained. Furthermore, the detail pinning schemes deciding what nodes should be chosen as pinned candidates and how many nodes are needed to be pinned for a fixed coupling strength are provided. The simple procedures illuminating how to design suitable intermittent controllers in real application are also given. Numerical simulations, including an undirected scale-free network and a directed small-world network, are finally presented to demonstrate the effectiveness of the theoretical results.

  15. When good pigeons make bad decisions: Choice with probabilistic delays and outcomes.

    Science.gov (United States)

    Pisklak, Jeffrey M; McDevitt, Margaret A; Dunn, Roger M; Spetch, Marcia L

    2015-11-01

    Pigeons chose between an (optimal) alternative that sometimes provided food after a 10-s delay and other times after a 40-s delay and another (suboptimal) alternative that sometimes provided food after 10 s but other times no food after 40 s. When outcomes were not signaled during the delays, pigeons strongly preferred the optimal alternative. When outcomes were signaled, choices of the suboptimal alternative increased and most pigeons preferred the alternative that provided no food after the long delay despite the cost in terms of obtained food. The pattern of results was similar whether the short delays occurred on 25% or 50% of the trials. Shortening the 40-s delay to food sharply reduced suboptimal choices, but shortening the delay to no food had little effect. The results suggest that a signaled delay to no food does not punish responding in probabilistic choice procedures. The findings are discussed in terms of conditioned reinforcement by signals for good news. © Society for the Experimental Analysis of Behavior.

  16. Survey of transmission line corridors. [Data on delays in transmission line construction

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-05

    The intent of this study is to determine the extent of delays experienced in planning and constructing transmission lines in the continental United States. The reasons for the delays are identified for each line studied and their effect on the total electrical system is sought. Data was collected for 136 different lines either recently built or currently under study. Statistics were developed for each line in several categories and comparisons of lines delayed were made by company, area served and generation capacity. From the study presented here it was found that: right-of-way acquisition procedures including condemnation and easement negotiation practices delay more projects than local, state and federal regulatory requirements combined; load growth reductions particularly in the east have reduced the impact of regulatory delays; the south, southeast and southwestern areas of the country experience fewer delays in constructing transmission lines than the more populated states, and the cost for corridor delays was responded to for only 17 of the 142 projects surveyed. By far the most costly delay is the expense of condemning land for transmission right-of-way.

  17. Review and evaluation of information on the thermal performance of ultimate heat sinks: spray ponds and cooling ponds

    International Nuclear Information System (INIS)

    Drake, R.L.

    1975-09-01

    A report is presented which identifies and evaluates available information and data useful in validating and improving existing models for the thermal performance of ultimate heat sinks. Included are discussions of the thermal elements of cooling ponds and spray ponds, the available information and data pertinent to the problem, and the requirements and needs for further research and performance data. An outline is presented of the necessary elements required for a performance test of an ultimate heat sink before the system is thermally approved. (auth)

  18. Comparison between field data and ultimate heat-sink cooling-pond and spray-pond models

    International Nuclear Information System (INIS)

    Codell, R.

    1982-09-01

    Two previously published reports, NUREG-0693 and NUREG-0733, presented models and methods by which ultimate heat sink cooling ponds and spray ponds used for safety-related water supplies in nuclear power plants could be analyzed for design-basis conditions of heat load and meteorology. These models were only partially verified with field data. The present report compares the NRC models to data collected for NRC by Battelle Pacific Northwest Laboratories on the performance of small geothermally heated ponds and spray ponds. These comparisons generally support the conclusion that the NRC models are useful tools in predicting ultimate heat sink performance

  19. Computer assisted procedure maintenance

    International Nuclear Information System (INIS)

    Bisio, R.; Hulsund, J. E.; Nilsen, S.

    2004-04-01

    The maintenance of operating procedures in a NPP is a tedious and complicated task. Through the whole life cycle of the procedures they will be dynamic, 'living' documents. Several aspects of the procedure must be considered in a revision process. Pertinent details and attributes of the procedure must be checked. An organizational structure must be created and responsibilities allotted for drafting, revising, reviewing and publishing procedures. Available powerful computer technology provides solutions within document management and computerisation of procedures. These solutions can also support the maintenance of procedures. Not all parts of the procedure life cycle are equally amenable to computerized support. This report looks at the procedure life cycle in todays NPPs and discusses the possibilities associated with introduction of computer technology to assist the maintenance of procedures. (Author)

  20. Factors affecting professional delay in diagnosis and treatment of oral cancer in Iran.

    Science.gov (United States)

    Esmaelbeigi, Farhad; Hadji, Maryam; Harirchi, Iraj; Omranipour, Ramesh; vand Rajabpour, Mojtaba; Zendehdel, Kazem

    2014-04-01

    Oral cancer is the most common malignant tumor among head and neck cancers. Delay in diagnosis affects the treatment and prognosis of oral cancer. We measured the professional delay in the diagnosis and its attributes in the Cancer Institute of Iran, the largest referral center for oral cancer patients in the country.  We interviewed oral cancer patients to measure the delay and used case-control approach to study association of various prognostic factors with professional delay and tumor stage. Out of 206 patients, 71.4% were diagnosed at the advanced stage. The median of the patient, professional and total delays were 45, 86 and 140 day, receptively. In the univariate model, prescription of medicines like analgesics (OR = 5.3, 95% CI 2.2-12.9) and history of dental procedure (OR=6.8, 95% CI 1.7-26.9) were associated with higher risk of delay compared to patient who were biopsied from the beginning. History of loose teeth increased risk of delay 4 times (OR = 4.0, 95% CI 1.6-9.8). Patients with primary education had 70% lower risk of delay compared to the illiterate patients (OR = 0.3, 95% CI 0.1-0.7) and the risk was lower among patients who had diploma (OR = 0.04, 95% CI 0-0.7) and college education (OR = 0.1, 95% CI 0-0.4). The delayed patients were diagnosed in more advanced stage compared to the patients without delay (OR = 2.1, 95% CI 1.0-4.4). Development of a national guideline for follow-up of oral lesions, training and awareness of health care professionals about oral cancer diagnosis may decrease the delay and improve the oral cancer outcome in Iran.

  1. The delay of the environmental licensing in oil activities and legal implications regarding the oil block; O atraso do licenciamento ambiental nas atividades petroliferas e as implicacoes atinentes ao cumprimento de prazo de bloco licitados

    Energy Technology Data Exchange (ETDEWEB)

    Cavalcante, Hellen Priscilla Marinho; Xavier, Yanko Marcius de Alencar [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2012-07-01

    This work intends to demonstrate how the delay in issuing environmental licenses by the appropriate bodies affect the correct fulfillment of the exploratory phase of blocks already bid and rendered to the lessees. Thus, it will be conducted a study of the pertaining legislation to the subject, such as Law n. 6.938/81 and its recent amendment by Complementary Law n. 140/2011, as well as the Resolutions issued by the National Environmental Council (CONAMA), addressing the vital importance of the environmental licensing process to the preservation of the environment ante the installation of potentially harmful activities. It is also acknowledged, through the analysis of articles and paragraphs, that there is a legal gap concerning the deadline for issuance of certain documents required to start the licensing procedure by the companies, which ultimately jeopardizes the fulfillment of their exploration activities in due time. Furthermore, there is not a provision regarding the return of the deadline to the lessee when it is suspended or extended due to licensing delays for reasons beyond its control, which cannot lack a reasonable answer. Therefore, as a conclusion, it will be presented a possible solution, so as to ensure the proper accomplishment of the oil activities combined with the preservation of the environment. (author)

  2. Lev Shestov as a Theologian and the Theology of the Great and Ultimate Battle

    Directory of Open Access Journals (Sweden)

    Natalya Bonetskaya

    2015-04-01

    Full Text Available Lev Shestov’s early period in which he developed his religious views is the subject of this article. Shestov was a well-known Russian thinker. The author sheds some light on the furtive character of his thought as well as attempts to reconstruct the sources of his religious consciousness. He was formed at the border between two religious worlds — that of Judaism and that of Christianity. Traces of Jewish free-thinking typical of the end of the nineteenth century color his Weltanschauung together with the infl uence of Nietzsche and the Bible, the last as it was interpreted by the western tradition. Shestov understands God in a way akin to that of anthropomorphic psychology, an understanding which develops the concept of the deity into a form of radical apophatic ignorance or the complete absence of the ability to know God. The author points out that Shestov’s God is not the God of life and religious experience but rather a product of a kind of radicalized rationality. This notwithstanding, the original theological perceptions of Shestov were generated by his search for an authentic philosophical life. The author concentrates her attention on two main tendencies in Shestov’s understanding of life — a holistic tendency and a personalistic tendency. From a reading of Shestov’s first book (Shakespeare and his critic Brandes published in 1898 it becomes clear that the personalistic tendency won out. The concept of rebellion takes first place in Shestov’s thought as well as that of the great and ultimate battle. As a result Shestov’s thought becomes dominated by anthopology rather than theology and the concept of God gives way to that of man as the rebel. Shestov’s thought, particularly in his works dating from the second half of the twentieth century, falls under the influence of Nietzsche and the man from the underground of Dostoevsky. His God becomes the God of Manichaeism, on the far side of neither good nor evil, and his

  3. Dynamics of Nonlinear Time-Delay Systems

    CERN Document Server

    Lakshmanan, Muthusamy

    2010-01-01

    Synchronization of chaotic systems, a patently nonlinear phenomenon, has emerged as a highly active interdisciplinary research topic at the interface of physics, biology, applied mathematics and engineering sciences. In this connection, time-delay systems described by delay differential equations have developed as particularly suitable tools for modeling specific dynamical systems. Indeed, time-delay is ubiquitous in many physical systems, for example due to finite switching speeds of amplifiers in electronic circuits, finite lengths of vehicles in traffic flows, finite signal propagation times in biological networks and circuits, and quite generally whenever memory effects are relevant. This monograph presents the basics of chaotic time-delay systems and their synchronization with an emphasis on the effects of time-delay feedback which give rise to new collective dynamics. Special attention is devoted to scalar chaotic/hyperchaotic time-delay systems, and some higher order models, occurring in different bran...

  4. Group Delay of High Q Antennas

    DEFF Research Database (Denmark)

    Bahramzy, Pevand; Pedersen, Gert Frølund

    2013-01-01

    Group Delay variations versus frequency is an essential factor which can cause distortion and degradation in the signals. Usually this is an issue in wideband communication systems, such as satellite communication systems, which are used for transmitting wideband data. However, group delay can also...... become an issue, when working with high Q antennas, because of the steep phase shift over the frequency. In this paper, it is measured how large group delay variations can become, when going from a low Q antenna to a high Q antenna. The group delay of a low Q antenna is shown to be around 1.3 ns, whereas...... a high Q antenna has group delay of around 22 ns. It is due to this huge group delay variation characteristics of high Q antennas, that signal distortion might occur in the radio system with high Q antennas....

  5. Permutation entropy with vector embedding delays

    Science.gov (United States)

    Little, Douglas J.; Kane, Deb M.

    2017-12-01

    Permutation entropy (PE) is a statistic used widely for the detection of structure within a time series. Embedding delay times at which the PE is reduced are characteristic timescales for which such structure exists. Here, a generalized scheme is investigated where embedding delays are represented by vectors rather than scalars, permitting PE to be calculated over a (D -1 ) -dimensional space, where D is the embedding dimension. This scheme is applied to numerically generated noise, sine wave and logistic map series, and experimental data sets taken from a vertical-cavity surface emitting laser exhibiting temporally localized pulse structures within the round-trip time of the laser cavity. Results are visualized as PE maps as a function of embedding delay, with low PE values indicating combinations of embedding delays where correlation structure is present. It is demonstrated that vector embedding delays enable identification of structure that is ambiguous or masked, when the embedding delay is constrained to scalar form.

  6. Time Delay Estimation Algoritms for Echo Cancellation

    Directory of Open Access Journals (Sweden)

    Kirill Sakhnov

    2011-01-01

    Full Text Available The following case study describes how to eliminate echo in a VoIP network using delay estimation algorithms. It is known that echo with long transmission delays becomes more noticeable to users. Thus, time delay estimation, as a part of echo cancellation, is an important topic during transmission of voice signals over packetswitching telecommunication systems. An echo delay problem associated with IP-based transport networks is discussed in the following text. The paper introduces the comparative study of time delay estimation algorithm, used for estimation of the true time delay between two speech signals. Experimental results of MATLab simulations that describe the performance of several methods based on cross-correlation, normalized crosscorrelation and generalized cross-correlation are also presented in the paper.

  7. CGI delay compensation. [Computer Generated Image

    Science.gov (United States)

    Mcfarland, R. E.

    1986-01-01

    Computer-generated graphics in real-time helicopter simulation produces objectionable scene-presentation time delays. In the flight simulation laboratory at Ames Research Center, it has been determined that these delays have an adverse influence on pilot performance during agressive tasks such as nap of the earth (NOE) maneuvers. Using contemporary equipment, computer generated image (CGI) time delays are an unavoidable consequence of the operations required for scene generation. However, providing that magnitude distortions at higher frequencies are tolerable, delay compensation is possible over a restricted frequency range. This range, assumed to have an upper limit of perhaps 10 or 15 rad/sec, conforms approximately to the bandwidth associated with helicopter handling qualities research. A compensation algorithm is introduced here and evaluated in terms of tradeoffs in frequency responses. The algorithm has a discrete basis and accommodates both a large, constant transport delay interval and a periodic delay interval, as associated with asynchronous operations.

  8. Memorized discrete systems and time-delay

    CERN Document Server

    Luo, Albert C J

    2017-01-01

    This book examines discrete dynamical systems with memory—nonlinear systems that exist extensively in biological organisms and financial and economic organizations, and time-delay systems that can be discretized into the memorized, discrete dynamical systems. It book further discusses stability and bifurcations of time-delay dynamical systems that can be investigated through memorized dynamical systems as well as bifurcations of memorized nonlinear dynamical systems, discretization methods of time-delay systems, and periodic motions to chaos in nonlinear time-delay systems. The book helps readers find analytical solutions of MDS, change traditional perturbation analysis in time-delay systems, detect motion complexity and singularity in MDS; and determine stability, bifurcation, and chaos in any time-delay system.

  9. Mnemonic abilities of primary school children with delayed mental development.

    Directory of Open Access Journals (Sweden)

    Murafa S.V.

    2015-07-01

    Full Text Available This paper presents the results of research regarding the mnemonic abilities of primary school children with developmental delays. Empirical studies of impaired mental development offer an opportunity to elucidate the psychological mechanisms underlying the process of normal development and enable us to consider at a micro level the formation of mental processes in ontogeny, which would, under normal conditions, be nondescript and not always amenable to psychological analysis. The research addresses an experimental investigation of productivity and qualitative characteristics of mnemonic abilities among primary school students with developmental delays. V.D. Shadrikov’s Theory of Abilities, developed in a systemic approach framework, is the theoretical basis of the research. The method of deploying a memorization activity, as elaborated by V.D. Shadrikov and L.V. Cheremoshkina, was the investigation tool used. The sample included students in grades 1 to 4 between ages 7 to 12 and included a total of 100 children (66 boys and 34 girls. The control group of primary school students with typical development included 105 children (50 boys and 55 girls. The research consisted of several stages: a pilot study, experimental research (the test task was to memorize card #1; the basic task was to memorize cards #2 and #3; to reproduce cards #2 and #3; and to poll the students, mathematical data processing, and a description of the levels of mnemonic ability development among primary students with developmental delays. The following procedures were employed during statistical analysis: Spearman r3, Mann-Whitney U-test, Jonckheere-Terpstra test, and Kruskal-Wallis test. The structure of mnemonic abilities in primary schoolchildren with developmental delays was determined to vary according to the underdevelopment of their operational mechanisms. For example, memory functions are based on the use of inborn mechanisms, and a portion of children differ in the

  10. Magnetic pulse sharpener and delay-line

    International Nuclear Information System (INIS)

    Li Jin; Dai Guangsen; Xia Liansheng

    2002-01-01

    This paper describes a method to achieve short rise time pulse which has been delayed with a delay-line and magnetic pulse sharpener. A delay-line and two shock-lines are designed to carry pulsed signal with a maximum voltage magnitude up to 80 kV. A pulse of High voltage with arise time of 48 ns at a level of 0.1%-0.9% were achieved, and the attenuation in the line is very small

  11. Does Bilingualism Delay the Development of Dementia?

    OpenAIRE

    Amy L Atkinson

    2016-01-01

    It has been suggested that bilingualism (where individuals speak two languages) may delay the development of dementia. However, much of the research is inconclusive. Some researchers have reported that bilingualism delays the onset and diagnosis of dementia, whilst other studies have found weak or even detrimental effects. This paper reviews a series of nine empirical studies, published up until March 2016, which investigated whether bilingualism significantly delays the onset of dementia. Th...

  12. Delayed enhanced MRI in intraparenchymal tumors

    International Nuclear Information System (INIS)

    Eguchi, Takahiko; Morimoto, Tetsuya; Takeshima, Toshikazu

    1991-01-01

    Delayed enhanced MRI was performed on 20 intraparenchymal tumors, and these findings were compared with those of early enhanced MRI. Using the spin-echo technique (SE: 400-500/20 msec), early scans were obtained 5 minutes, and delayed scans were obtained 60 minutes, after the intravenous injection of 0.1 nmol of gadolinium-DTPA/Kg. We discussed the changes in the delayed scan with regard to the change in the pattern of enhancement and the boundary of enhancement. In these twenty intraparenchymal tumors, there were three low-grade astrocytomas, two anaplastic astrocytomas, seven glioblastomas, and eight metastatic tumors. The changes in the enhanced pattern showed three types as follows: Type I: heterogeneous enhancement in both early and delayed scans; Type II: heterogeneous enhancement in early scan and homogeneous enhancement in delayed scan; Type III: homogeneous enhancement in both early and delayed scans. Most malignant tumors, such as glioblastomas (6/8), anaplastic astrocytomas (2/2), and metastatic tumors (7/8), revealed Type I, although low-grade astrocytomas showed Type II (3/2) and Type III (1/3). The heterogeneous enhancement in delayed scan was found in malignant tumors and in low-grade astrocytoma; even if the early scan revealed heterogeneous enhancement, the delayed scan showed homogeneous enhancement. In the delayed scan, most enhanced boundaries spread out of the boundaries in the early scan. Glioblastomas spread markedly in the delayed scan, although none of the low-grade astrocytomas, anaplastic astrocytomas, or metastases revealed marked spreading. We called these marked increases in the delayed scan a 'spreading sign' and thought that this sign was specific to glioblastomas. Recently some authors have emphasized the usefulness of serial scans. Delayed enhanced MRI 60 minutes after the administration of a contrast medium was here found also to be useful for the accurate diagnosis for brain tumors. (author)

  13. Response procedure, memory, and dichotic emotion recognition.

    Science.gov (United States)

    Voyer, Daniel; Dempsey, Danielle; Harding, Jennifer A

    2014-03-01

    Three experiments investigated the role of memory and rehearsal in a dichotic emotion recognition task by manipulating the response procedure as well as the interval between encoding and retrieval while taking into account order of report. For all experiments, right-handed undergraduates were presented with dichotic pairs of the words bower, dower, power, and tower pronounced in a sad, angry, happy, or neutral tone of voice. Participants were asked to report the two emotions presented on each trial by clicking on the corresponding drawings or words on a computer screen, either following no delay or a five second delay. Experiment 1 applied the delay conditions as a between-subjects factor whereas it was a within-subject factor in Experiment 2. In Experiments 1 and 2, more correct responses occurred for the left than the right ear, reflecting a left ear advantage (LEA) that was slightly larger with a nonverbal than a verbal response. The LEA was also found to be larger with no delay than with the 5s delay. In addition, participants typically responded first to the left ear stimulus. In fact, the first response produced a LEA whereas the second response produced a right ear advantage. Experiment 3 involved a concurrent task during the delay to prevent rehearsal. In Experiment 3, the pattern of results supported the claim that rehearsal could account for the findings of the first two experiments. The findings are interpreted in the context of the role of rehearsal and memory in models of dichotic listening. Copyright © 2013 Elsevier Inc. All rights reserved.

  14. Delayed replantation of avulsed teeth

    Directory of Open Access Journals (Sweden)

    Adil N

    2007-05-01

    Full Text Available Dental injuries are very common and their extent has been classified by Ellis. Avulsion of tooth is a grievous injury and ranges from 1-16% among the traumatic injuries, of which maxillary anterior are commonest. Reimplantation of avulsed teeth is a standard procedure. However, it has certain limitations. Most often their management is very challenging. In this case report we are presenting the management of maxillary incisors by replantation after 36 hrs in a 12 year old girl.

  15. Queerspawn Speak out: A Review of "Let's Get This Straight: The Ultimate Handbook for Youth with LGBTQ Parents"

    Science.gov (United States)

    Ryan, Caitlin L.

    2012-01-01

    "Let's Get This Straight: The Ultimate Handbook for Youth With LGBTQ Parents" provides an engaging and accessible set of tools for youth from LGBTQ-headed families. The stories and resources shared encourage these youth to take pride in their families, value their diverse experiences, and work against homophobia, transphobia, and other forms of…

  16. 26 CFR 48.6420-1 - Credits or payments to ultimate purchaser of gasoline used on a farm.

    Science.gov (United States)

    2010-04-01

    ... gasoline used on a farm. 48.6420-1 Section 48.6420-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT... § 48.6420-1 Credits or payments to ultimate purchaser of gasoline used on a farm. (a) In general. If gasoline is used on a farm for farming purposes after June 30, 1965, a credit (under the circumstances...

  17. The ultimate SharePoint performance guide ! configuring SharePoint, SQL and Office 365 for maximum performance

    CERN Document Server

    Catrinescu, Vlad

    2017-01-01

    This is an ultimate guidance on performance for SharePoint Server 2013, 2016 and SharePoint Online inspired both by Microsoft’s best practices and real life experiences from countless deployments on the field.This book was Tech Reviewed by Microsoft MVP & RD Jussi Roine and includes an awesome foreword by SharePoint MVP Christian Buckley.

  18. Experimental investigation on ultimate strength and failure response of composite box beams used in wind turbine blades

    DEFF Research Database (Denmark)

    Tang, Jing; Chen, Xiao

    2018-01-01

    This study focuses on the ultimate strength and failure response of composite box beams under three-point bending. The box beams consist of spar caps and shear webs and they are typically used in wind turbine blades as load-carrying members. Different spar cap configurations and loading directions...

  19. The stiffness change and the increase in the ultimate capacity for a stiff pile resulting from a cyclic loading

    DEFF Research Database (Denmark)

    Lada, Aleksandra; Ibsen, Lars Bo; Nicolai, Giulio

    In the paper the experimental results of small-scale tests on a stiff monopile are presented to outline the change in stiffness during the cyclic loading and the change in the ultimate pile capacity. The results confirm the increase of stiffness and the increase in bearing capacity resulting from...

  20. Ultimate Attainment in Late Second Language Acquisition: Phonetic and Grammatical Challenges in Advanced Dutch-English Bilingualism

    Science.gov (United States)

    Schmid, Monika S.; Gilbers, Steven; Nota, Amber

    2014-01-01

    The present article provides an exploration of ultimate attainment in second language (L2) and its limitations. It is argued that the question of maturational constraints can best be investigated when the reference population is bilingual and exposed on a regular basis to varieties of their first language (L1) that show cross-linguistic influence.…